Implementation of an analytical technique for Samarium; Implementacion de una tecnica analitica para Samario

Energy Technology Data Exchange (ETDEWEB)

Garcia G, N. [ININ, Carretera Mexico-Toluca Km. 36.5, 52045 Estado de Mexico (Mexico)

2004-07-01

Since the Samarium presents the same chemical properties that the plutonium, it has been used as homologous in studies that allow us to know the behavior that the plutonium presents in solution, with the advantage of working with an inactive and not very dangerous element. At the moment studies of sorption of plutonium or samarium are made on some mineral matrices that present certain surface properties. Due to the low concentrations that are used in the studies of sorption of samarium on those reagent substrates, their detection becomes very difficult for the conventional analysis media. The luminescence is a technique that can detect lower concentrations, smaller at 1 X 10{sup -} {sup 2} M, but when fluorofors are used this limit of detection increases in several orders of magnitude. In this work it has been used the arsenazo-III as fluorofor agent since it reacts in a specific way with the samarium, forming a complex that presents a proportional luminescence to the concentration of the present samarium. The advantage of making the quantification of samarium by luminescence is that it can use the same instrumental equipment to determine the speciation of the samarium sipped in the zircon. (Author)

Adsorption and the initial stages of samarium condensation on iridium coated by graphite monolayer

International Nuclear Information System (INIS)

Abdullaev, R.M.; Tontegode, A.Ya.; Yusifov, F.K.

1978-01-01

Adsorption and the initial stages of vacuum samarium condensation on iridium coated by graphite monolayer (valent-saturated neutral substrate) were studied by the thermodesorption mass-spectrometry and thermoemission methods, and were compared with samarium adsorption and condensation on iridium. Desorption heat of samarium atoms with thin coating of Ir-C, equal to E approximately 1.9 eV has been determined. For desorption with Ir E is approximately 6 eV. Such a great difference in desorption heats is connected with the reduction of covalent constituent of adsorption bond in a neutral substrate. Samarium on Ir-C is found to be condensated in two states: loosely bound and tightly bound which sharply differ in properties. The tightly bound state is characterized by abnormally low vapour pressure. Possible nature of this state is discussed. Double effect on the condensation of the substrate valent saturation is noted. On the one hand, the reduction of the particle bond with the substrate decreases their concentration on the surface, preventing condensation. On the other hand, the release of the valent eloctrons of adatous brings about strong lateral interaction between them, which in its turn, promotes condensation during eased migration on the neutral substrate

Effective visible light-active nitrogen and samarium co-doped BiVO{sub 4} for the degradation of organic pollutants

Energy Technology Data Exchange (ETDEWEB)

Wang, Min; Niu, Chao [College of Environmental and Chemical Engineering, Shenyang Ligong University, Shenyang 110165 (China); Liu, Jun, E-mail: minwang62@msn.com [Shenyang Military General Hospital, Shenyang 110016 (China); Wang, Qianwu; Yang, Changxiu; Zheng, Haoyan [College of Environmental and Chemical Engineering, Shenyang Ligong University, Shenyang 110165 (China)

2015-11-05

Nitrogen and samarium co-doped BiVO{sub 4} (N–xSm–BiVO{sub 4}) nanoparticles were synthesized using a sol–gel method with a corn stem template. The physicochemical properties of the resultant N–xSm–BiVO{sub 4} particles were characterized using various methods: XPS, XRD, SEM, BET, and UV–Vis DRS analyses. The visible-light photocatalytic activity was successfully demonstrated by degrading a model dye, namely, methyl orange. The dopant content was optimized, and the nitrogen and samarium co-doped BiVO{sub 4} extended the light absorption spectrum toward the visible region, significantly enhancing the photodegradation of the model dye. The Sm and N co-doped BiVO{sub 4} exhibited the highest photocatalytic activity compared to materials with a single dopant or no dopant. The significantly enhanced photocatalytic activity of the N–Sm co-doped BiVO{sub 4} under visible-light irradiation can be attributed to the synergistic effects of the nitrogen and samarium. - Highlights: • The N–Sm codoped BiVO{sub 4} were synthesized using a sol–gel method with a corn stem template. • The N and Sm codoped BiVO{sub 4} has excellent photocatalytic activity of methyl orange degradation. • The maximum activity was observed when the molar ratio of Sm/Bi was 1.0. • The high photocatalytic activity was caused by the synergistic effects between N doping and Sm doping.

Biodistribution study of 153Sm-EDTMP produced by irradiation of natural and enriched Samarium, in rats

International Nuclear Information System (INIS)

Meftahi, M.; Bahrami Samani, A.; Babaei, M. H.; Shamsaei Zafarghandi, M.; Ghannadi Maragheh, M.

2010-01-01

''1 53 Sm-EDTMP is one of the well known radiopharmaceuticals for pain palliation of bone metastases. Despite that, it is used just in a few countries. It is due to some reasons like being costly enriched samarium that usually used as target for irradiation and short half-life of 153 Sm. In this investigation, certain amounts of radiopharmaceuticals prepared by irradiation of enriched and natural samarium were injected to some normal rats. Then, the rodents were sacrificed and some of their organs were removed. All of the mentioned stages were performed in order to consider the possibility of exploiting natural samarium instead of enriched samarium by study of biodistribution of both radiopharmaceuticals in various organs especially in bone as the target tissue. At the end, the acceptable results were obtained using natural samarium in comparison with the enriched samarium from the point of view of the biodistribution studies.

A NOVEL SAMARIUM COMPLEX WITH INTERESTING ...

African Journals Online (AJOL)

delocalized π-electrons of the pyridyl rings obtains increasing attention in ... BaSO4 plate was used as a reference (100% reflectance), on which the finely ground .... several are samarium-containing complex with bipy [41-45]. Figure 2.

Solubility isotherms in ternary systems of samarium nitrate, water and nitrates of amidopyrine, benzotriazole

International Nuclear Information System (INIS)

Starikova, L.I.

1991-01-01

Solubility in the system of samarium nitrate-amidopyrine nitrate-water at 25 and 50 deg C was studied. Solubility isotherms consist of three branches, corresponding to crystallization of samarium nitrate tetrahydrate, amidopyrine nitrate and congruently soluble compounds of Sm(NO 3 ) 3 · 2C 13 H 17 ON 3 ·HNO 3 composition. Its thermal behaviour was studied. The system of samarium nitrate-benzotriazole nitrate-water is referred to eutonic type

Pressure and irradiation effects on transport properties of samarium compounds with instable valence

International Nuclear Information System (INIS)

Morillo, J.

1981-01-01

Electron transport properties in samarium compounds with instable valence are studied in this thesis: from SmS in its integer valence phases at common pressure to SmB 6 compound IV at common pressure through SmSsub(1-x)Psub(x) (x 6 is presented [fr

Basis for developing samarium AMS for fuel cycle analysis

International Nuclear Information System (INIS)

Buchholz, Bruce A.; Biegalski, Steven R.; Whitney, Scott M.; Tumey, Scott J.; Jordan Weaver, C.

2010-01-01

Modeling of nuclear reactor fuel burnup indicates that the production of samarium isotopes can vary significantly with reactor type and fuel cycle. The isotopic concentrations of 146 Sm, 149 Sm, and 151 Sm are potential signatures of fuel reprocessing, if analytical techniques can overcome the inherent challenges of lanthanide chemistry, isobaric interferences, and mass/charge interferences. We review the current limitations in measurement of the target samarium isotopes and describe potential approaches for developing Sm-AMS. AMS sample form and preparation chemistry will be discussed as well as possible spectrometer operating conditions.

4f and 5d magnetism in samarium

International Nuclear Information System (INIS)

Stunault, A.; Bernhoeft, N.; Vettier, C.; Dumesnil, K.; Dufour, C.

2001-01-01

We report on resonant magnetic X-ray scattering studies of a samarium epitaxial film at the samarium L 3 edge. We observe one quadrupolar resonance below the edge, reflecting the polarization of the 4f electrons, and two dipolar resonances above the edge, related to the polarization of the 5d band. We demonstrate, by following the thermal evolution of resonant magnetic intensities of both types, that the polarization of the 4f and 5d electrons present exactly the same temperature dependence, even very close to the ordering temperature, in agreement with the RKKY model for long-range magnetic order in rare earths

Studies on ultrasonic velocity and electrical conductivity of samarium soaps in non-aqueous medium

International Nuclear Information System (INIS)

Mehrotra, K.N.; Chauhan, M.; Shukla, R.K.

1990-01-01

The ultrasonic velocity of solutions of samarium soaps in non-aqueous medium has been measured at a constant temperature and the results have been used to evaluate the various acoustic parameters. The pre-micellar association and the formation of micelles in samarium soap solutions have been determined by conductometric measurements. The molar conductance at infinite dilution, degree of ionisation and ionisation constant have been evaluated. The results show that samarium soaps behave as weak electrolyte in dilute solutions. (Authors)

Nonlinear Faraday rotation in samarium vapor

International Nuclear Information System (INIS)

Barkov, L.M.; Melik-Pashaev, D.A.; Zolotorev, M.S.

1988-01-01

Experiments on nonlinear magnetic optical (Faraday) rotation on resonance transitions of atomic samarium are described. Measurements were carried out on transitions with different angular momenta of upper and lower states: 1→0, 0→1 and 1→1. Qualitative explanations of observed phenomena are given

Plasma sprayed samarium--cobalt permanent magnets

International Nuclear Information System (INIS)

Willson, M.C.; Janowiecki, R.J.

1975-01-01

Samarium--Co permanent magnets were fabricated by arc plasma spraying. This process involves the injection of relatively coarse powder particles into a high temperature gas for melting and spraying onto a substrate. The technique is being investigated as an economical method for fabricating Co--rare earth magnets for advanced traveling wave tubes and cross-field amplifiers. Plasma spraying permits deposition of material at high rates over large areas with optional direct bonding to the substrate, and offers the ability to fabricate magnets in a variety of shapes and sizes. Isotropic magnets were produced with high coercivity and good reproducibility in magnetic properties. Post-spray thermal treatments were used to enhance the magnetic properties of sprayed deposits. Samarium--Co magnets, sprayed from Sm-rich powder and subjected to post-spray heat treatment, displayed energy products in excess of 9 million G-Oe and coercive forces of approximately 6000 Oe. Bar magnet arrays were constructed by depositing magnets on ceramic substrates

Magnetoresistance of samarium in the 4.2-300 K range

International Nuclear Information System (INIS)

Trubitsyn, V.A.; Shalashov, V.F.

1980-01-01

Electric conductivity, transverse and longitudinal magnetoresistance of polycrystalline samarium with the purity of 99.9% in the 4.2-300 K temperature range and in magnetic fields up to 50 ke, are measured. The constituent of specific electric conductivity caused by spin disorder is 30.7 μOhmxcm, m*/m=2.6, the exchange parameter is G=3.1 eVxA 3 . Both transverse and longitudinal magnetoresistance are positive at 4.2 K; and the increase of temperature reveals a number of anomalies, evidently conditioned by the alteration of samarium magnetic structure

Conductometric investigations on samarium soaps

International Nuclear Information System (INIS)

Mehrotra, K.N.; Chauhan, Mithlesh; Shukla, R.K.

1989-01-01

The critical micelle concentration (CMC), degree of dissociation and dissociation constant of samarium soaps (valerate, caproate, caprylate and caprate) in a mixture of 60 per cent benzene and 40 per cent methanol were determined by using conductometric measurements. The soaps behaved as simple electrolyte in dilute solutions and the CMC was found to decrease with increasing chainlength of the fatty acid constituent of the soap. (author). 7 refs., 2 tabs

Optical isotope shifts for unstable samarium isotopes

International Nuclear Information System (INIS)

Eastham, D.A.; Walker, P.M.; Griffith, J.A.R.; Evans, D.E.; Grant, I.S.; England, J.G.; Fawcett, M.J.

1984-01-01

Using a tunable dye laser beam intersecting a thermal atomic beam, optical isotope shifts and hyperfine splittings have been measured for the four unstable samarium isotopes between 144 Sm and 154 Sm, covering the well known transition region from spherical to deformed shapes. (orig.)

The samarium Grignard reaction. In situ formation and reactions of primary and secondary alkylsamarium(III) reagents

Energy Technology Data Exchange (ETDEWEB)

Curran, D.P.; Totleben, M.J. [Univ. of Pittsburgh, PA (United States)

1992-07-15

This work shows that primary and secondary radicals are rapidly reduced in THF/HMPA to form primary- and secondary-alkylsamarium reagents. The primary- and secondary-radicals can be formed either by direct SmI{sup 2} reductions of primary- and secondary-halides or by a previous rapid radical cyclization. The samarium reagents have moderate stability in solution, and they react with a variety of typical electrophiles, including aldehydes and ketones. The work further shows that organosamarium intermediates can be involved in the traditional samarium Barbier reaction of aldehydes and ketones conducted in THF/HMPA. A new procedure called the {open_quotes}samarium Grignard{close_quotes} method is introduced, and it is suggested that this new procedure will have considerably more scope and generality than the samarium Barbier reaction. 37 refs., 4 tabs.

Memory effect of calcined layered samarium hydroxy chlorides in aqueous solution

International Nuclear Information System (INIS)

Lee, Byung Il; Byeon, Song Ho

2015-01-01

The decomposition and recovery behavior of layered samarium hydroxychloride (Sm 2 (OH) 5 Cl·nH 2 O, LSmH) has been closely studied in various conditions. Although the heat treatment of LSmH at 700 °C completely collapsed typical layered structure, the calcined LSmH (c-LSmH) recovered its layered characteristics and consequently its ability to intercalate anions into the interlayer space when it was rehydroxylated and rehydrated in aqueous solutions containing organic and inorganic anions. This phenomenon is similar to the memory effect observed in classical layered double hydroxides (LDHs), where LDHs calcined to a mixture of metal oxides can recover their layered structures in aqueous solutions. In contrast, the recovery reaction of c-LSmH in water without any counter anions was unsuccessful and instead resulted in the formation of Sm(OH) 3 . Such a difference was interpreted on the basis of the salt effect on Sm 2 (OH) 5 Cl·nH 2 O–Sm(OH) 3 phase equilibria in water

Influence of pretreatment temperature cycling on the radiating defect formation in silicon doped by samarium

International Nuclear Information System (INIS)

Abdurakhmanov, K.P.; Nazyrov, D.E.

2006-01-01

Full text: The raise of thermal and radiation stability as it is known, is one of actual problems of physics semiconductors. Recently it is established, that the rare-earth elements (REE) raise a stability of silicon to exterior action. In this connection the investigation of silicon doped REE by samarium and influence on its properties of heat treatments and radiation exposure is important. In sectional operation the outcomes of investigations of influence of samarium on thermal (600 degree C are reduced; 600 deg. + 900 deg. C; 900 deg. C; 900 deg. C + 600 deg. C; 1100 deg. C; 600 deg. C + 900 deg. C + 1100 deg. C; 900 deg. C + 600 deg. C + 1100 deg. C) thermal defect formation and radiation defect formation (exposure of γ-quanta 60 Co) both in beforehand wrought, and in thermally unfinished samples. After each cycle of heat treatments samples cool fast (throwing off in oil) or slowly (together with the furnace). Doping n-silicon REE by gadolinium and samarium was carried out during cultivation. The concentration of gadolinium and samarium in silicon, on sectional of a neutron-activation analysis was equaled 10 14 - 10 18 cm -3 . As control is model monocrystal silicon such as KEP-15/50. Para-meters of deep levels originating in control and doped REE samples, both past heat treatment or temperature cycling, and irradiated by the γ-quanta are defined by methods of a capacity spectroscopy: DLTS and IRC. The obtained outcomes have shown, that in irradiated with the γ-quanta 60 Co deep levels samples are formed with energies: E C -0,17 eV, E C -0,32 eV, EC-0,41 eV. Thus the parameters of deep levels vary depending on requirements of prestress heat treatment. For example heat treatment at 600 deg. C essentially increments a velocity of introduction of and centre (deep level of E C -0,17 eV), in comparison with a velocity of introduction of this level in samples with prestress heat treatment at 900 deg. C. In samples n-Si doped by samarium effectiveness of formation

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

Energy Technology Data Exchange (ETDEWEB)

Shaorong Liu; Jian Meng (Beijing Research Institute of Chemical Engineering and Metallurgy (China)); Wenhua Liu (General Research Institute for Non-Ferrous Metals (China))

1992-08-24

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs.

Fluorimetric determination of samarium(III) and europium(III) in neodymium oxide by separation with a resin column

International Nuclear Information System (INIS)

Shaorong Liu; Jian Meng; Wenhua Liu

1992-01-01

When thenoyltrifluoroacetone-phenanthroline-Triton X-100 is used to determine samarium(III) and europium(III) fluorimetrically, only a limited amount of neodymium(III) can be tolerated. By using an on- line separation which can partially separate neodymium(III) from samarium(III), a practical and convenient method was developed to detect samarium(III) at concentrations >0.05% and europium(III) at concentrations >0.005% in neodymium oxide. (author). 7 refs.; 4 figs.; 3 tabs

ppt level detection of samarium(III) with a coated graphite sensor based on an antibiotic.

Science.gov (United States)

Ganjali, Mohammad Reza; Rezapour, Morteza; Pourjavid, Mohammad Reza; Haghgoo, Soheila

2004-07-01

N-[2-[4-[[[(Cyclohexylamino)carbonyl]amino]sulfonyl]phenyl]ethyl]-5-methyl pyrazine carboxamide (glipizid) was explored as an electro-active material for preparing a polymeric membrane-based sensor selective to samarium ions. The membrane incorporated 30% poly(vinyl chloride) (PVC), 53% benzyl acetate (BA), 11% glipizid and 6% sodium tetraphenyl borate. When coated on the surface of a graphite electrode, it exhibits Nernstian responses in the concentration range of 1.0 x 10(-5) to 1.0 x 10(-10) M, with a detection limit of 8.0 x 10(-11)M samarium. The electrode shows high selectivity towards samarium over several cations (alkali, alkaline earth, transition and heavy metal ions), and specially lanthanide ions. The proposed sensor has a very short response time (pH range for at least ten weeks. It was used as an indicator electrode in potentiometric titration of Sm(III) ions with an EDTA solution, and for determination of samarium in binary and ternary mixtures.

Laser spectroscopy of atomic samarium

International Nuclear Information System (INIS)

Barkov, L.M.; Melik-Pashaev, D.A.; Zolotorev, M.S.

1988-01-01

Samarium spectrum was studied with a purpose to find transitions to be used in experiments on parity nonconservation. Macaluso-Corbino effect - Faraday rotation near resonance was used for the search and study of spectral lines. We have identified previously unknown energy levels belonging to the 4f 5 6s 2 5 D term: 15914.55(3) cm -4 (J=1), 17864.29(3) cm -4 (J=2), 20195.76(3) cm -4 (J=3). M1-transitions to these levels from the levels of the ground 4f 5 6s 2 7 F term were observed. There are several peculiarities of these transitions which are due to the fact that they occut within an inner 4f 5 -shell, particularly, a very small presuure broadening by inert gases. 44 refs.; 17 figs.; 7 tabs

Solar nebula heterogeneity in p-process samarium and neodymium isotopes.

Science.gov (United States)

Andreasen, Rasmus; Sharma, Mukul

2006-11-03

Bulk carbonaceous chondrites display a deficit of approximately 100 parts per million (ppm) in 144Sm with respect to other meteorites and terrestrial standards, leading to a decrease in their 142Nd/144Nd ratios by approximately 11 ppm. The data require that samarium and neodymium isotopes produced by the p process associated with photodisintegration reactions in supernovae were heterogeneously distributed in the solar nebula. Other samarium and neodymium isotopes produced by rapid neutron capture (r process) in supernovae and by slow neutron capture (s process) in red giants were homogeneously distributed. The supernovae sources supplying the p- and r-process nuclides to the solar nebula were thus disconnected or only weakly connected.

Removal of trivalent samarium from aqueous solutions by activated biochar derived from cactus fibres

Institute of Scientific and Technical Information of China (English)

Loukia Hadjittofi; Styliana Charalambous; Ioannis Pashalidis

2016-01-01

The efficiency of activated biochar fibres obtained fromOpuntia Ficus Indica regarding the sorption of trivalent samarium (Sm(III)) from aqueous solutions was investigated by batch experiments. The effect of various physicochemical parameters (e.g. pH, initial metal concentration, ionic strength, temperature and contact time) on the Sm(III) adsorption was studied and the surface species were characterized by FTIR spectroscopy prior to and after the lanthanide sorption. The experimental results showed that the acti-vated biochar fibres possessed extraordinary sorption capacity for Sm(III) in acidic solutions (qmax=90 g/kg, pH 3.0) and near neutral solutions (qmax=350 g/kg, pH 6.5). This was attributed to the formation of samarium complexes with the surface carboxylic moieties, available in high density on the lamellar structures of the bio-sorbent.

Crystallization of Yttrium and Samarium Aluminosilicate Glasses

OpenAIRE

Lago, Diana Carolina; Prado, Miguel Oscar

2016-01-01

Aluminosilicate glasses containing samarium and yttrium (SmAS and YAS glasses) exhibit high glass transition temperatures, corrosion resistance, and glass stability on heating which make them useful for technological applications. Yttrium aluminosilicate glass microspheres are currently being used for internal selective radiotherapy of liver cancer. During the preparation process, crystallization needs to be totally or partially avoided depending on the final application. Thus knowing the cry...

Determination of 0.01–0.1% of samarium in 40–100 mg of lead chloride

NARCIS (Netherlands)

Agterdenbos, J.; Jütte, B.A.H.G.; Schuring, J.

1971-01-01

A method is described for the determination of 5–25 μg of samarium in about 40 mg of lead chloride, based on the removal of the lead by electrolysis and determination of the samarium by extraction with PAN and measurement of the extinction of the complex at 552 nm.

Synthesis and structure of unprecedented samarium complex with bulky bis-iminopyrrolyl ligand via intramolecular C=N bond activation

Energy Technology Data Exchange (ETDEWEB)

Das, Suman; Anga, Srinivas; Harinath, Adimulam; Panda, Tarun K. [Department of Chemistry, Indian Institute of Technology, Hyderabad (India); Pada Nayek, Hari [Department of Applied Chemistry, Indian Institute of Technology, (ISM) Dhanbad, Jharkhand (India)

2017-12-29

An unprecedentate samarium complex of the molecular composition [{κ"3-{(Ph_2CH)N=CH}{sub 2}C{sub 4}H{sub 2}N}{κ"3-{(Ph_2CHN=CH)(Ph_2CHNCH)C_4H_2N}Sm}{sub 2}] (2), which was isolated by the reaction of a potassium salt of 2,5-bis{N-(diphenylmethyl)-iminomethyl}pyrrolyl ligand [K(THF){sub 2}{(Ph_2CH)N=CH}{sub 2}C{sub 4}H{sub 2}N] (1) with anhydrous samarium diiodide in THF at 60 C through the in situ reduction of imine bond is presented. The homoleptic samarium complex [[κ{sup 3}-{(Ph_2CH)-N=CH}{sub 2}C{sub 4}H{sub 2}N]{sub 3}Sm] (3) can also be obtained from the reaction of compound 1 with anhydrous samarium triiodide (SmI{sub 3}) in THF at 60 C. The molecular structures of complexes 2 and 3 were established by single-crystal X-ray diffraction analysis. The molecular structure of complex 2 reveals the formation of a C-C bond in the 2,5-bis{N-(diphenylmethyl)iminomethyl}pyrrole ligand moiety (Ph{sub 2}Py{sup -}). However, complex 3 is a homoleptic samarium complex of three bis-iminopyrrolyl ligands. In complex 2, the samarium ion adopts an octahedral arrangement, whereas in complex 3, a distorted three face-centered trigonal prismatic mode of nine coordination is observed around the metal ion. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Graphite furnace atomic absorption spectrometry with a tantalum boat for the determination of yttrium, samarium, and dysprosium in a mish metal

International Nuclear Information System (INIS)

Daidoji, Hidehiro; Tamura, Shohei

1982-01-01

The determination of yttrium, samarium, and dysprodium by means of graphite-furnace atomic absorption spectrometry (AAS) was studied by a tantalum boat inserted into a graphite tube atomizer. These elements could not be determined by the use of a commercial graphite tube, In the atomization from a tantalum boat, better analytical sensitivities and negligible memory effects for these rare earths are obtained. The analytical sensitivities of yttrium, samarium, and dysprodium with the tantalum boat were 0.60 ng, 0.86 ng, and 0.17 ng respectively. This method was applied for the determination of yttrium, samarium, and dysprosium in a mish metal. The measurements were performed with slightly acidified solutions (0.01 mol dm 3 HCI or HNO 3 ). The sensitivities and the precisions for these elements decreased with increasing acid concentration. An enhancement in the sensitivities of yttrium and dysprosium upon the addition of a large excess of lanthanum, neodymium, and praseodymium salts were observed. The yttrium, samarium, and dysprosium in a mish metal were determined with both analytical curves of standard solutions containing an excess of lanthanum, cerium, and neodymium ions and of the standard addition. The precisions for this work were in the 3 - 9.3% range. (author)

Ultrasonic and viscosimetric studies of samarium laurate in benzene-dimethylsulfoxide mixtures

International Nuclear Information System (INIS)

Mehrotra, K.N.; Anis, M.

1995-01-01

Ultrasonic and viscosity measurements of samarium laurate in benzene-DMSO mixtures of different compositions (7:3 and 1:1 V/V) have been used to determine the critical micelle concentration (CMC), soap-solvent interaction, and various acoustic parameters of the system. The values of critical micelle concentration increase with increasing amount of DMSO in the solvent mixtures. The viscosity results have been explained on the basis of equations proposed by Einstein, Vand. Moulik, and Jones-Dole. The values of CMC for samarium laurate obtained from the viscosity measurements are in agreement with the results obtained from ultrasonic measurements. The results show that the soap molecules do not aggregate appreciably below CMC there is a marked change in the aggregation behaviour at CMC. (author)

Behavior of Samarium III during the sorption process; Comportamiento del Samario-III durante el proceso de sorcion

Energy Technology Data Exchange (ETDEWEB)

Ordonez R, E.; Garcia G, N.; Garcia R, G. [ININ, Carr. Mexico-Toluca Km 36.5, Salazar, Estado de Mexico (Mexico)]. e-mail: edo@nuclear.inin.mx

2004-07-01

In this work the results of the behavior of samarium in solution are presented, in front of a fine powder of zirconium silicate (zircon). For that which is necessary to characterize the zircon, studying the crystallinity, the morphology, the surface area and the isoelectric point. The behavior of samarium in solution is studied by means of the elaboration of isotherm of sorption, using the technique by lots. One observes that to pH values of nearer to the isoelectric point (pH = 7.23) the process of sorption of the samarium begins, reaching a maximum to near pH at 9. The technique of luminescence is used to determine the concentration of the sipped samarium (phosphorescence) and also to make the speciation of the species formed in the surface of the zircon (phosphorescence). The results can be extrapolated with the plutonium when making the modeling of the migration of alpha emitting coming from the repositories of radioactive waste since both they have similar chemical properties (they are homologous). (Author)

Inductively coupled plasma optical emission spectrometry analysis of lanthanum, samarium and gadolinium oxides for rare earths impurities

International Nuclear Information System (INIS)

Reino, L.C.P.; Lordello, A.R.

1990-09-01

An inductively coupled plasma optical emission spectrometry method is described for the determination of Sm, Eu, La, Gd, Dy, Pr, Ho, Nd, Tb and Y in purified oxides of lanthanum, samarium and gadolinium. The method enables a simple, precise and readily available determination. Dissolution of the samples is achieved with diluted hydrochloric acid (1:1). The solutions are diluted to volume for a concentration of 1mg/ml. The lowest determination limit is 0,01% for most elements and 0,05 or 0,1% for a few rare earths in samarium and gadolinium matrices. Lanthanum, Samarium and Gadolinium concentrates with purity grade of 99,9%, 99,6% and 99,8%, respectively, can be analysed by this procedure. (author)

Pemisahan Unsur Samarium dan Yttrium dari Mineral Tanah Jarang dengan Teknik Membran Cair Berpendukung (Supported Liquid Membrane

Directory of Open Access Journals (Sweden)

Amri Amin

2009-06-01

Full Text Available he increasing use of rare earth elements in high technology industries needs to be supported by developmental work for the separation of elements. The research objective is fiercely attracting and challenging considering the similarity of bath physical and chemical properties among these elements. The rate separation of samarium and yttrium elements using supported liquid membrane has been studied. Polytetrafluoroethylene (PTFE with pore size of 0.45 µm has been used as the membrane and di(2-ethylhexyl phosphate (D2EHP in hexane has been used as a carrier and nitric acid solution has been used as receiving phase. Result of experiments showed that the best separation rate of samarium and yttrium elements could be obtained at feeding phase of pH 3.0, di(2-ethylhexyl phosphate (D2EHP concentration of 0.3 M, agitation rate of 700 rpm, agitation time of 2 hours, and nitric acid and its solution concentrations of 1.0 M and 0.1 M, respectively. At this condition, separation rates of samarium and yttrium were 64.4 and 67.6%, respectively.   Keywords: liquid membrane, rare earth elements, samarium, yttrium

Australian manufacture of QuadrametTM (Samarium-153 EDTMP)

International Nuclear Information System (INIS)

Wood, N.R.; Whitwell, J.

1997-01-01

Quadramet T (Samarium-153 EDTMP) has been shown overseas to be potentially useful in the palliation of painful osteoblastic skeletal metastases and has been approved this year for general marketing in the USA. Australian Radioisotopes (ARI) has licensed this product from the Australian patent holders, Dow Chemical. Within the facilities of ARI, a hot cell has been dedicated to this product and fitted out to manufacture it weekly on a cycle related to the operating cycle of the Australian reactor HIFAR. Due to neutron flux limitations of HIFAR, the local formulation has an elemental Samarium content up to 200μg/mL whereas the overseas formulation has a level of 20-46μg/mL. All other specifications of the two products are essentially the same. In 1995 and 1996 a small clinical trial with 19 patients was held which demonstrated that the pharmacokinetic behaviour was also essentially the same by measuring blood clearance rates and skeletal uptake dynamics. Soft tissue uptake was also qualitatively determined. The ARI version is now the subject of an application for general marketing within Australia. Some useful characteristics of this agent are: almost complete excretion or fixation in the skeleton within 6 hours, rapid onset of clinical effect, applicability in most cases where an abnormal diagnostic bone scan correlates with painful sites, dosage can be tailored to individual patient uptake due to easy dose measurement and retreatment is quite possible. The use of this class of agents in pain palliation continues to increase. Australian manufacture of Quadramet TM provides a further option in the management of these difficult cases

Sorption-desorption of samarium in Febex bentonite

International Nuclear Information System (INIS)

Ramirez-Guinart, O.; Rigol, A.; Vidal, M.; Fernandez-Poyatos, P.; Alba, M. D.

2012-01-01

with a Be window. Determination of Sm in the solutions derived from sorption-desorption experiments. Samarium concentrations were determined with ICP-OES and ICP-MS. The wavelength used in the ICP-OES was 359.3 nm, whereas the isotope 147 Sm was used in the ICP-MS. The quantification limits for the ICP-OES and ICP-MS were 30 μg L -1 and 10 ng L -1 , respectively. The initial sample shows an asymmetric 001 reflexion whose maximum corresponds to a basal spacing of 14.6 A and a shoulder to a higher 2θ. This is compatible with a heterogeneity composition of the interlayer space where divalent cations predominate. After sorption in water and at increasing Sm concentrations, the peaks became symmetric and the 001 reflexion shifted progressively to lower 2θ up to a basal spacing of 15.3 A compatible with a more homogeneous composition of the interlayer space and the exchange of the original interlayer divalent cations with Sm. These results indicated that whereas at lower concentration sorption was controlled by inner-sphere mechanisms, at higher initial Sm concentrations the predominant sorption mechanism was cationic exchange. The scenario differed when the sorption took place in the interstitial water medium, as the 001 reflexion did not shift to lower 2θ, but it widened and slightly shifted to higher 2θ. Both facts indicate competitiveness between Sm and the cations in the solution. Although the affinity for the interlayer space, in general, increases with the cation charge and then favors Sm, this was only observed for the highest initial Sm concentrations. Samarium sorption-desorption Samarium sorption was higher in water than in the interstitial, basically due to the cationic competition effect both for specific and for ionic-exchange, regular sites. This was consistent with results from the XRD analyses, and it was corroborated by the increase in the divalent cation concentrations in the final solutions after sorption when increasing samarium initial

Preparation and examination of properties of samarium-153-EDTMP complex

International Nuclear Information System (INIS)

Nowak, M.; Garnuszek, P.; Lukasiewicz, A.; Wozniak, I.; Zulczyk, W.; Licinska, I.

1995-01-01

Preparation and properties of ethylenediaminetetramethylenephosphonic acid (EDTMP) as well as some properties of 153 Sm-EDTMP chelate have been examined. The chelate formed by samarium-153 (46.3 h, β - -decay) with EDTMP exhibits high bone uptake and can be used for treatment of disseminated, painful skeletal metastases. The purity and stability of solutions of 153 Sm-EDTMP chelate were examined in a broad range of samarium concentration and 153 Sm specific activity. The complex under study was examined by radio-TLC, -electrophoresis and radio-HPLC. The results obtained suggest the small size of molecules of 153 Sm-EDTMP chelate as compared with molecules of ''free''EDTMP. The results of biodistribution of 153 Sm-EDTMP determined in rats indicate the quick blood clearance, high deposition of radioactivity in bone and quick excretion of radioactivity into urine. No specific uptake of 153 Sm-EDTMP in extra-skeletal organs was found. (author). 42 refs, 13 figs, 22 tabs

Expedient Method for Samarium(II) Iodide Preparation Utilizing a Flow Approach

Czech Academy of Sciences Publication Activity Database

Voltrová, Svatava; Šrogl, Jiří

2013-01-01

Roč. 24, č. 3 (2013), s. 394-396 ISSN 0936-5214 R&D Projects: GA MŠk LH12013 Institutional support: RVO:61388963 Keywords : flow * samarium * iodide * reduction Subject RIV: CC - Organic Chemistry Impact factor: 2.463, year: 2013

Thermomechanical behavior of Fe-Mn-Si-Cr-Ni shape memory alloys modified with samarium

International Nuclear Information System (INIS)

Shakoor, R.A.; Khalid, F. Ahmad

2009-01-01

The deformation and training behavior of Fe-14Mn-3Si-10Cr-5Ni (wt.%) shape memory alloys containing samarium addition has been studied in the iron-based shape memory alloys. It is noticed that thermomechanical treatment (training) has significant influence on proof stress, critical stress and shape memory behavior of the alloys. The improvement in shape memory behavior can be attributed to the decrease in the proof stress and critical stress which facilitates the formation of ε (hcp martensite). It is also observed that alloy 2 containing samarium undergoes less softening as compared to alloy 1 with training which inhibits the formation of α (bcc martensite) and thus enhances the shape memory behavior. The excessive thermomechanical treatment with increase in the training cycle has led to the formation of α (bcc martensite) along with ε (hcp martensite) in the alloy 1 which appeared to have decline in the shape memory effect. This has been demonstrated by the examination of microstructure and identification of α (bcc martensite) martensite in the alloy 1 as compared to alloy 2

Optical properties of zinc–vanadium glasses doped with samarium ...

Indian Academy of Sciences (India)

Abstract. Zinc–vanadium glasses doped with samarium oxide having the chemical composition Sm2O3(x). ZnO(40−x)V2O5(60)(where x = 0·1–0·5 mol%) were prepared by melt quenching method. The density of these glasses was measured by Archimedes method; the corresponding molar volumes have also been ...

X-ray spectrum in the range (6-12) A emitted by laser-produced plasma of samarium

International Nuclear Information System (INIS)

Louzon, Einat; Henis, Zohar; Levi, Izhak; Hurvitz, Gilad; Ehrlich, Yosi; Fraenkel, Moshe; Maman, Shlomo; Mandelbaum, Pinchas

2009-01-01

A detailed analysis of the x-ray spectrum emitted by laser-produced plasma of samarium (6-12 A) is presented, using ab initio calculations with the HULLAC relativistic code and isoelectronic considerations. Resonance 3d-nf (n=4 to 7), 3p-4d, 3d-4p, and 3p-4s transitions in Ni samarium ions and in neighboring ionization states (from Mn to Zn ions) were identified. The experiment results show changes in the fine details of the plasma spectrum for different laser intensities.

Synthesis of samarium binding bleomycin - a possible NCT radiosensitizer

Energy Technology Data Exchange (ETDEWEB)

Mendes, B.M., E-mail: bmm@cdtn.b [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Mendes, T.M.; Campos, T.P.R., E-mail: campos@nuclear.ufmg.b [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)

2011-07-01

Bleomycin (BLM) is a drug that has attractive features for the development of a new radiopharmaceutical, particularly with regard to neutron capture therapy (NCT) sensitized by Sm-149. It has the ability to chelate many metal ions. In vitro studies have shown that up to 78% of BLM present in a cell is accumulated inside the nucleus or in the nuclear membrane. In addition, this drug has higher affinity for tumor tissues than for normal tissues. Radioactive isotopes carried by this antibiotic would be taken preferentially to one important cellular targets DNA. Besides, BLM displays intrinsic anti-tumor activity - it is a chemotherapic antibiotic clinically used against some cancers. This study aimed to obtain bleomycin molecules bound to samarium (BLM-Sm) for NCT studies in vitro and in vivo. The binding technique employed in this work has great simplicity and low cost. Thin layer chromatography, high performance liquid chromatography, fast protein liquid chromatography and analysis by ICP-AES were applied to verify the binding molecule. ICP-AES results showed the presence of samarium in the sample peaks related to BLM-Sm. However, efficiency and stability of this bond needs to be investigated. (author)

Synthesis of samarium binding bleomycin - a possible NCT radiosensitizer

International Nuclear Information System (INIS)

Mendes, B.M.; Mendes, T.M.; Campos, T.P.R.

2011-01-01

Bleomycin (BLM) is a drug that has attractive features for the development of a new radiopharmaceutical, particularly with regard to neutron capture therapy (NCT) sensitized by Sm-149. It has the ability to chelate many metal ions. In vitro studies have shown that up to 78% of BLM present in a cell is accumulated inside the nucleus or in the nuclear membrane. In addition, this drug has higher affinity for tumor tissues than for normal tissues. Radioactive isotopes carried by this antibiotic would be taken preferentially to one important cellular targets DNA. Besides, BLM displays intrinsic anti-tumor activity - it is a chemotherapic antibiotic clinically used against some cancers. This study aimed to obtain bleomycin molecules bound to samarium (BLM-Sm) for NCT studies in vitro and in vivo. The binding technique employed in this work has great simplicity and low cost. Thin layer chromatography, high performance liquid chromatography, fast protein liquid chromatography and analysis by ICP-AES were applied to verify the binding molecule. ICP-AES results showed the presence of samarium in the sample peaks related to BLM-Sm. However, efficiency and stability of this bond needs to be investigated. (author)

Sorption of samarium in iron (II) and (III) phosphates in aqueous systems

International Nuclear Information System (INIS)

Diaz F, J.C.

2006-01-01

The radioactive residues that are stored in the radioactive confinements its need to stay isolated of the environment while the radioactivity levels be noxious. An important mechanism by which the radioactive residues can to reach the environment, it is the migration of these through the underground water. That it makes necessary the investigation of reactive materials that interacting with those radionuclides and that its are able to remove them from the watery resources. The synthesis and characterization of materials that can be useful in Environmental Chemistry are very important because its characteristics are exposed and its behavior in chemical phenomena as the sorption watery medium is necessary to use it in the environmental protection. In this work it was carried out the sorption study of the samarium III ion in the iron (II) and (III) phosphate; obtaining the sorption isotherms in function of pH, of the phosphate mass and of the concentration of the samarium ion using UV-visible spectroscopy to determine the removal percentage. The developed experiments show that as much the ferrous phosphate as the ferric phosphate present a great affinity by the samarium III, for what it use like reactive material in contention walls can be very viable because it sorption capacity has overcome 90% to pH values similar to those of the underground and also mentioning that the form to obtain these materials is very economic and simple. (Author)

Impact of educational strategies in positioning Samarium-153 EDTMP as a treatment for metastatic bone pain

International Nuclear Information System (INIS)

Seminario, C.; Morales, R.; Castro, M.; Cano, R.A.; Mendoza, G.

2005-01-01

To educate is a difficult task but its results make efforts worthwhile. Many patients in Peru suffer from intractable bone pain due to metastases. Since 1993 radionuclides were used to palliate bone pain due to metastases in Peru. First, with the help of the IAEA, Peru participated in a clinical trial using Phosphorus 32 and Strontium 89. Then, efforts were performed to produce Samarium 153 EDMTP locally, which was achieved in 1995. Nevertheless, years passed and Samarium use did not increase proportionally to the needs of people with cancer and bone pain, mainly the poor. Educational strategies have been proven useful for delivering solutions to many health problems in other diseases and also in cancer. Health education makes patients and their relatives assume responsible care of their problems. The purpose of this work was to increase Samarium EDTMP use as palliative treatment in patients with bone pain due to metastases, using educational strategies as means to change attitudes towards this health problem. In September 2003, a task group conducted studies in order to apply several methods to achieve the goal of increasing Samarium EDTMP use. Educational strategies employed were performed to provide verbal and written information to patients, physicians, medical students, residents, pain specialists, oncologists and neurologists, as well as general public. Verbal information included radio interviews, television spots and a phone number (in charge of two secretaries, prepared for answering and if not possible, a physician was in charge of attending patient consultation), e-mail and a web page for consultation. Written material was delivered to several newspapers, including clinical use of Samarium, possibilities of being elected for treatment, benefits and risks and a photography of the product. Politics of the institution producing Samarium changed, in order to achieve minimum cost of the product and it was delivered to all publics at the lowest cost for a year

Lanthanum (samarium) nitrate-4-aminoantipyrine nitrate-water systems

International Nuclear Information System (INIS)

Starikova, L.I.; Zhuravlev, E.F.

1985-01-01

Using the isothermal method of cross-sections at 50 deg C systems lanthanum nitrate-4-aminoantipyrine nitrate-water (1), samarium nitrate-4-aminoantipyrine nitrate-water (2), are studied. Isotherms of system 1 consist of two crystallization branches of initial salt components. In system 2 formation of congruently soluble compounds of the composition Sm(No) 3 ) 3 xC 11 H 13 ON 3 xHNO 3 is established. Analytical, X-ray phase and thermogravimetric analysis of the isolated binary salt are carried out

Synthesis of samarium, europium and ytterbium acetylenides

International Nuclear Information System (INIS)

Bochkarev, M.N.; Fedorova, E.A.; Glushkova, N.V.; Protchenko, A.V.; Druzhkov , O.N.; Khorshev, S.Ya.

1995-01-01

Ethynyl complexes of samarium, europium and ytterbium were prepared by interaction of naphthalinides of metals with acetylene in tetrahydrofuran. The compounds are isolated in the form of dark-coloured pyrophore powders. Data of magnetic measurements suggest that in the course of the reaction Sm(2) is oxidized completely to Sm(3), Yb(2) transforms into Yb(3) partially, whereas europium preserves its initial bivalent state. Hydrolysis of the compounds prepared provides acetylene, ethylene, ethane and hydrogen which indicates the presence of acethylenide Ln 2 C 2 and hydride LnH groupings (Ln = Sm, Eu, Yb). 9 refs., 2 tabs

Synthesis of samarium complexes with the derivative binder of Schiff Quinolinic base. Characterization and photophysical study

International Nuclear Information System (INIS)

Lucas H, J.

2016-01-01

In this work we determined the metal: binder stoichiometry of the species formed during the UV/Vis spectrophotometric titration of the derivative binder of Schiff quinolinic base, L1 with the samarium nitrate pentahydrate in methanol. Statistical analysis of the data allowed proposing the metal: binder stoichiometry for the synthesis of the complexes which was one mole of samarium salt by 2.5 moles of binder and thus favor the formation of complexes with 1M: 1L and 1M: 2L stoichiometries. They were synthesized in aqueous-organic medium (water-ethanol), isolated and purified two complexes with stoichiometry 1 Sm: 1 L1, complex 1 and 1 Sm: 2 L1, complex 2. The overall yield of the reaction was 76%. The characterization of the formed complexes was performed by visible ultraviolet spectrometry (UV/Vis), nuclear magnetic resonance, X-ray photoelectron spectroscopy (XP S), thermal gravimetric analysis with differential scanning calorimetry (TGA/DSC), and radial distribution function. These complexes were studied by fluorescence and emission phosphorescence at variable temperature. Spectroscopic techniques used in both solution and solid demonstrated the formation and stability of these complexes. In addition XP S indicated that in both complexes the samarium retains its oxidation state 3+. Luminescence studies indicated that there is intra-binding charge transfer which decreases the transfer of light energy from the binder to the samarium. Based on the experimental results, L1 binder molecules and complexes 1 and 2 were modeled that demonstrated the proposed Nc for each complex, as well as allowed to visualize the structural arrangement of the molecules, complexes and binder. (Author)

Myelotoxicity of Samarium Sm153 lexidronam in patients with painful bony metastases

International Nuclear Information System (INIS)

Ben Ghachem, T.; Mhiri, A.; Slim, I.; Bahloul, A.; Yeddes, I.; Elbez, I.; Meddeb, I.; Ben Slimene, M.F.

2015-01-01

Full text of publication follows. Introduction: the management of bone pain includes analgesia, radiation, hormones, radiofrequency (RF) ablation, chemotherapy, and surgery. Bone pain palliation therapy with radiopharmaceuticals is a cost-effective systemic therapy to relieve pain from skeletal metastases with a consequent decrease in morbidity and an improvement in quality of life. The aim of our study is to evaluate the effect of myelotoxicity of samarium lexidronam (Sm 153 ) in patients with painful bony metastasis. Methods: we reviewed 116 patients aged from 14 to 87 years old, 91 males (78%) and 25 females (22%), having received 1 to 4 treatments of Sm 153 (37 MBq/kg) for painful bony metastases from different primitive tumors: 67 cases of prostate cancer (57.7%), 22 cases of breast cancer (18.9%), 10 cases of pulmonary cancer (8.6%) and others in 14.6% of cases. Clinical follow-up was available for 159 treatments, consisting on blood count each week over at least two months, in order to evaluate myelotoxicity according to WHO classification. Results: no patients had grade 4 toxicity after its cures. A grade 2-3 myelotoxicity was observed after 52 treatments (34%) during the second week and after 50 treatments (32.6%) during the fourth week with a satisfactory reversibility. At 10 weeks of treatment, myelotoxicity was reclassified from 0 to 2 for 139 cures (90,8%). Moreover, we found that prior treatment with radiotherapy or chemotherapy did not affect the rates of myelotoxicity. Conclusion: multiple treatments with samarium Sm 153 lexidronam had no significant effect on myelotoxicity. Patients with bone predominant metastatic disease may survive for extended periods of time and may safely be treated with multiple modalities of therapy. (authors)

On the effects of pressure and irradiation on the transport properties of samarium compounds with unstable valence

International Nuclear Information System (INIS)

Morillo, J.

1983-06-01

We present the first extensive study of electronic transport properties of ''quasi-stoichiometric'' SmS as a function of pressure P, temperature T, magnetic field B and defect concentration C. SmS which is a semiconductor, undergoes with increasing P a first order transition towards an homogeneous intermediate valence state. In the semiconducting phase (s.c.), the energie epsilon(f) necessary to delocalize a 4f electron increases greatly with T and is about 250meV at 300K. The phase diagram for the first order electronic transition Sm 2 + →Smsup(2+epsilon) with P has been determined for T 6 has been investigated by resistivity measurements under irradiation at 21K. The threshold energy Ed for displacement of Sm in SmS has been determined: Ed(Sm) = 20 +- 2 eV, and the observed effects of irradiation have been associated to samarium displacements (vacancies and interstitials) [fr

Polypyrrole-coated samarium oxide nanobelts: fabrication, characterization, and application in supercapacitors

Science.gov (United States)

Liu, Peng; Wang, Yunjiao; Wang, Xue; Yang, Chao; Yi, Yanfeng

2012-11-01

Polypyrrole-coated samarium oxide nanobelts were synthesized by the in situ chemical oxidative surface polymerization technique based on the self-assembly of pyrrole on the surface of the amine-functionalized Sm2O3 nanobelts. The morphologies of the polypyrrole/samarium oxide (PPy/Sm2O3) nanocomposites were characterized using transmission electron microscope. The UV-vis absorbance of these samples was also investigated, and the remarkable enhancement was clearly observed. The electrochemical behaviors of the PPy/Sm2O3 composites were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge. The results indicated that the PPy/Sm2O3 composite electrode was fully reversible and achieved a very fast Faradaic reaction. After being corrected into the weight percentage of the PPy/Sm2O3 composite at a current density of 20 mA cm-2 in a 1.0 M NaNO3 electrolyte solution, a maximum discharge capacity of 771 F g-1 was achieved in a half-cell setup configuration for the PPy/Sm2O3 composites electrode with the potential application to electrode materials for electrochemical capacitors.

Peculiarities of electronic, phonon and magnon subsystems of lanthanum and samarium tetraborides

Energy Technology Data Exchange (ETDEWEB)

Novikov, V.V., E-mail: vvnovikov@mail.ru; Mitroshenkov, N.V.; Matovnikov, A.V.

2015-10-15

Experimental research was carried out to study the temperature dependences of heat capacity C{sub p}(T = 2–300 K), lattice parameters a(T), and ≿(T), (5–300 K) of lanthanum and samarium tetraborides. A comparison with data obtained previously for LuB{sub 4} reveals the peculiar influence of lanthanide contraction and the rare-earths mass on the thermodynamic properties of rare earth tetraborides at low and high temperatures. Sharp anomalies were found in the heat capacity and thermal expansion for SmB{sub 4} at T{sub N} = 25.1 K, conditioned by the phase transition into antiferromagnetic state. The more poorly defined heat capacity anomaly around 7 K is referred to the quadrupole orbital fluctuation of the atomic magnetic moments for Sm{sup 3+} ions. The electronic, lattice, and magnetic contributions to the heat capacity and thermal expansion of samarium tetraboride were defined. Our approach makes it possible to adequately approximate the lattice components of heat capacity and thermal expansion by combining the Debye and Einstein contributions, which are based on the joint analysis of calorimetric and X-ray data. The influence of the frustration of the atomic magnetic moment system for Sm{sup 3+} ions on the thermodynamic characteristics of the samarium tetraboride magnetic phase transition was revealed. - Highlights: • The heat capacity and lattice parameters for LaB{sub 4} and SmB{sub 4} were determined at 2–300 K. • The anomalies of C{sub p}(T), a(T), c(T) for SmB{sub 4} due to the phase transition are revealed. • The lattice contributions to the thermal properties of LaB{sub 4} and SmB{sub 4} are analyzed.

Ekstraksi Pemisahan Neodimium dari Samarium, Itrium dan Praseodimium Memakai Tri Butil Fosfat

Directory of Open Access Journals (Sweden)

Maria Veronica Purwani

2017-05-01

Full Text Available The extraction of Nd(OH3 (neodymium hydroxide concentrate containing Y (yttrium, Sm (samarium and Pr (praseodymium as product of monazite processed has been done. The purpose of this study is to determine the separation of Nd from Y, Pr and Nd Sm in Nd concentrate. The aqueous phase was concentrated Nd (OH3 in HNO3 and extractant while organic phase was Tri Butyl Phosphate (TBP in kerosene. Parameters studied were pH and concentration feed, concentration of TBP in kerosene, extraction time and stirring speed. The result showed that the optimization of separation extraction neodymium from samarium, yttrium and praseodymium in Nd(OH3 concentrated with TBP, obtained the optimum condition of pH = 0.2, concentration of feed 100 g /L, concentration of TBP in kerosene 5%, extraction time 15 minutes and stirring speed 150 rpm. With the conditions, Separation Factor (SF obtained for Nd-Y, Nd-Pr, Nd-Sm are 2.242, 4.811, 4.002 respectively, while D and extraction efficiency of Nd are 0.236 and 19.07%.

Polypyrrole-coated samarium oxide nanobelts: fabrication, characterization, and application in supercapacitors

Energy Technology Data Exchange (ETDEWEB)

Liu Peng, E-mail: pliu@lzu.edu.cn; Wang Yunjiao; Wang Xue; Yang Chao; Yi Yanfeng [College of Chemistry and Chemical Engineering, Lanzhou University, Key Laboratory of Nonferrous Metal Chemistry and Resources Utilization of Gansu Province and State Key Laboratory of Applied Organic Chemistry (China)

2012-11-15

Polypyrrole-coated samarium oxide nanobelts were synthesized by the in situ chemical oxidative surface polymerization technique based on the self-assembly of pyrrole on the surface of the amine-functionalized Sm{sub 2}O{sub 3} nanobelts. The morphologies of the polypyrrole/samarium oxide (PPy/Sm{sub 2}O{sub 3}) nanocomposites were characterized using transmission electron microscope. The UV-vis absorbance of these samples was also investigated, and the remarkable enhancement was clearly observed. The electrochemical behaviors of the PPy/Sm{sub 2}O{sub 3} composites were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, and galvanostatic charge-discharge. The results indicated that the PPy/Sm{sub 2}O{sub 3} composite electrode was fully reversible and achieved a very fast Faradaic reaction. After being corrected into the weight percentage of the PPy/Sm{sub 2}O{sub 3} composite at a current density of 20 mA cm{sup -2} in a 1.0 M NaNO{sub 3} electrolyte solution, a maximum discharge capacity of 771 F g{sup -1} was achieved in a half-cell setup configuration for the PPy/Sm{sub 2}O{sub 3} composites electrode with the potential application to electrode materials for electrochemical capacitors.

Production of SmCo5 alloy by calciothermic reduction of samarium oxide

International Nuclear Information System (INIS)

Krishnan, T.S.; Gupta, C.K.

1988-01-01

Among the established permanent magnets, SmCo 5 magnet occupies the foremost position as it offers a unique combination of high energy product, coercivity and curie temperature. The SmCo 5 magnets are thus extensively used for high field applications. These are also best suited for use in environments where high demagnetizing field and high temperature are operative. Also, for applications where high performance and miniaturization are the over-riding considerations, the choice again falls on SmCo 5 magnets. The main deterrent to the widespread use of SmCo 5 magnet is its high cost. Both samarium and cobalt metals are high priced, and the magnets prepared from their directly melted alloy are thus naturally very expensive. An alternate process involving calcium reduction of their oxide intermediates has, therefore, been studied and the alloy prepared by this process has been evaluated and found satisfactory for magnet production. The process essentially involves compaction of the charge mix containing samarium oxide, cobalt oxide (or metal) and calcium metal and reduction of the charge compact at 1000-1300 degrees C in hydrogen atmosphere, followed by water and acid leaching, drying and classification

Effects of increasing doses of samarium-153-ethylenediaminetetramethylene phosphonate on axial and appendicular skeletal growth in juvenile rabbits

International Nuclear Information System (INIS)

Essman, Stephanie C.; Lewis, Michael R.; Fox, Derek B.

2008-01-01

Introduction: Targeted radiotherapy using samarium-153-ethylenediaminetetramethylene phosphonate ( 153 Sm-EDTMP) is currently under investigation for treatment of osteosarcoma. Osteosarcoma often occurs in children, and previous studies on a juvenile rabbit model demonstrated that clinically significant damage to developing physeal cartilage may occur as a result of systemic 153 Sm-EDTMP therapy. The aim of this study was to evaluate the late effects of 153 Sm-EDTMP on skeletal structures during growth to maturity and to determine if there is a dose response of 153 Sm-EDTMP on growth of long bones. Methods: Female 8-week-old New Zealand white rabbits were divided into three treatment groups plus controls. Each rabbit was intravenously administered a predetermined dose of 153 Sm-EDTMP. Multiple bones of each rabbit were radiographed every 2 months until physeal closure, with subsequent measurements made to assess for abbreviated bone growth. Statistical analyses were performed to determine the differences in bone length between groups, with significance set at P 153 Sm-EDTMP. Further investigation regarding the effects of bone-seeking radiopharmaceuticals on bone growth and physeal cartilage is warranted

Samarium oxide as a radiotracer to evaluate the in vivo biodistribution of PLGA nanoparticles

CSIR Research Space (South Africa)

Mandiwana, V

2015-09-01

Full Text Available the biodistribution of poly(D,L-lactide-co-glycolide) (PLGA) nanoparticles containing samarium-153 oxide ([(sup153)Sm]Sm(sub2)O(sub3)) in vivo to prove that orally administered nanoparticles alter the biodistribution of a drug. These were then activated in a nuclear...

Synthesis of Samarium Cobalt Nanoblades

Energy Technology Data Exchange (ETDEWEB)

Darren M. Steele

2010-08-25

As new portable particle acceleration technologies become feasible the need for small high performance permanent magnets becomes critical. With particle accelerating cavities of a few microns, the photonic crystal fiber (PCF) candidate demands magnets of comparable size. To address this need, samarium cobalt (SmCo) nanoblades were attempted to be synthesized using the polyol process. Since it is preferable to have blades of 1-2 {micro}m in length, key parameters affecting size and morphology including method of stirring, reaction temperature, reaction time and addition of hydroxide were examined. Nanoparticles consisting of 70-200 nm spherical clusters with a 3-5 nm polyvinylpyrrolidone (PVP) coating were synthesized at 285 C and found to be ferromagnetic. Nanoblades of 25nm in length were observed at the surface of the nanoclusters and appeared to suggest agglomeration was occurring even with PVP employed. Morphology and size were characterized using a transmission electron microscope (TEM). Powder X-Ray Diffraction (XRD) analysis was conducted to determine composition but no supportive evidence for any particular SmCo phase has yet been observed.

Neutron Capture and Transmission Measurements and Resonance Parameter Analysis of Samarium

International Nuclear Information System (INIS)

Leinweber, G.; Burke, J.A.; Knox, H.D.; Drindak, N.J.; Mesh, D.W.; Haines, W.T.; Ballad, R.V.; Block, R.C.; Slovacek, R.E.; Werner, C.J.; Trbovich, M.J.; Barry, D.P.; Sato, T.

2001-01-01

The purpose of the present work is to accurately measure the neutron cross sections of samarium. The most significant isotope is 149 Sm, which has a large neutron absorption cross section at thermal energies and is a 235 U fission product with a 1% yield. Its cross sections are thus of concern to reactor neutronics. Neutron capture and transmission measurements were performed by the time-of-flight technique at the Rensselaer Polytechnic institute (RPI) LINAC facility using metallic and liquid Sm samples. The capture measurements were made at the 25 meter flight station with a multiplicity-type capture detector, and the transmission total cross-section measurements were performed at 15- and 25-meter flight stations with 6 Li glass scintillation detectors. Resonance parameters were determined by a combined analysis of six experiments (three capture and three transmission) using the multi-level R-matrix Bayesian code SAMMY version M2. The significant features of this work are as follows. Dilute samples of samarium nitrate in deuterated water (D 2 O) were prepared to measure the strong resonances at 0.1 and 8 eV without saturation. Disk-shaped spectroscopic quartz cells were obtained with parallel inner surfaces to provide a uniform thickness of solution. The diluent feature of the SAMMY program was used to analyze these data. The SAMMY program also includes multiple scattering corrections to capture yield data and resolution functions specific to the RPI facility. Resonance parameters for all stable isotopes of samarium were deduced for all resonances up to 30 eV. Thermal capture cross-section and capture resonance integral calculations were made using the resultant resonance parameters and were compared to results obtained using resonance parameters from ENDF/B-VI updated through release 3. Extending the definition of the capture resonance integral to include the strong 0.1 eV resonance in 149 Sm, present measurements agree within estimated uncertainties with En

Phase Composition of Samarium Niobate and Tantalate Thin Films Prepared by Sol-Gel Method

Science.gov (United States)

Bruncková, H.; Medvecký, Ľ.; Múdra, E.; Kovalčiková, A.; Ďurišin, J.; Šebek, M.; Girman, V.

2017-12-01

Samarium niobate SmNbO4 (SNO) and tantalate SmTaO4 (STO) thin films ( 100 nm) were prepared by sol-gel/spin-coating process on alumina substrates with PZT interlayer and annealing at 1000°C. The precursors of films were synthesized using Nb or Ta tartrate complexes. The improvement of the crystallinity of monoclinic M'-SmTaO4 phase via heating was observed through the coexistence of small amounts of tetragonal T-SmTa7O19 phase in STO precursor at 1000°C. The XRD results of SNO and STO films confirmed monoclinic M-SmNbO4 and M'-SmTaO4 phases, respectively, with traces of orthorhombic O-SmNbO4 (in SNO). In STO film, the single monoclinic M'-SmTaO4 phase was revealed. The surface morphology and topography of thin films were investigated by SEM and AFM analysis. STO film was smoother with roughness 3.2 nm in comparison with SNO (6.3 nm). In the microstructure of SNO film, small spherical ( 50 nm) and larger cuboidal particles ( 100 nm) of the SmNbO4 phase were observed. In STO, compact clusters composed of fine spherical SmTaO4 particles ( 20-50 nm) were found. Effect of samarium can contribute to the formation different polymorphs of these films for the application to environmental electrolytic thin film devices.

Identification of the lines in the L emission spectrum of cerium and samarium

International Nuclear Information System (INIS)

Shrivastava, B.D.; Singh, D.

1992-01-01

The occurrence of a line at 2.1556 A in the L emission spectrum of cerium and two lines at 1.6679 and 1.8379 A in the L emission spectrum of samarium, reported many years ago, has remained a puzzle. These have now been identified as EXAFS minima occurring at the L absorption edges of the respective elements. (author)

Samarium-153-EDTMP in the metastatic bone pain treatment

International Nuclear Information System (INIS)

Lins Filho, M.L.M.; Santos, A.O.; Nappi, A.P.B.; Meirelles, M.B.; Arouca, P.T.; Ramos, C.D.; Etchebehere, E.C.S.C.; Teixeira, L.C.; Netto Junior, N.R.; D'Ancona Cal; Camargo, E.E.

1997-01-01

Full text: Bone metastasis is the most reason of pain in prostate and mammary cancer patients. The Samarium-153-EDTMP has been showed as an alternative to the treatment of the metastasis bone pain. With the objective to evaluate the use of the Sm-153-EDTMP as a systemic therapy for the metastasis bone pain, 30 patients (19 male, 11 female, average age of 64,5 years) were studied. 19 patients with prostate cancer and 11 with mammary cancer. All the patients presented previous bone scintiscanning with multiple metastasis; interruption of the chemotherapy or radiotherapy for two or more weeks and leukocyte count higher than 2,000 leukocytes/mm 3 and platelets higher than 80,000/mm 3 . The patients were classified previously to the radioisotope therapy, as far the intensity of the pain in a scale from 0 to 10 is concerned. All the patients received 37 MBq/kg (1m Ci/kg) of weight of Sm-153-EDTMP by venous via. The evaluation 6 weeks after the therapy showed complete or partial pain relief in 22 patients (73,3%). Complete or partial pain relief has been obtained in 91,0% (10 in 11) of the patients with mammary cancer and in 62,2% (12 in 19) of the patients with prostate cancer. Transitory leukopenia (lower than 2,000 leukocytes/mm 3 ) and platelet count (lower than 80,000/mm 3 ) occurred in 33,3% of the patients. 8 patients (26,7%) did not responded to the therapy. The therapy with Samarium-153-EDTMP is a simple, safe and efficient method in the treatment of the bone pain caused by metastasis

Dependence of samarium-soil interaction on samarium concentration: Implications for environmental risk assessment.

Science.gov (United States)

Ramírez-Guinart, Oriol; Salaberria, Aitor; Vidal, Miquel; Rigol, Anna

2018-03-01

The sorption and desorption behaviour of samarium (Sm), an emerging contaminant, was examined in soil samples at varying Sm concentrations. The obtained sorption and desorption parameters revealed that soil possessed a high Sm retention capacity (sorption was higher than 99% and desorption lower than 2%) at low Sm concentrations, whereas at high Sm concentrations, the sorption-desorption behaviour varied among the soil samples tested. The fractionation of the Sm sorbed in soils, obtained by sequential extractions, allowed to suggest the soil properties (pH and organic matter solubility) and phases (organic matter, carbonates and clay minerals) governing the Sm-soil interaction. The sorption models constructed in the present work along with the sorption behaviour of Sm explained in terms of soil main characteristics will allow properly assessing the Sm-soil interaction depending on the contamination scenario under study. Moreover, the sorption and desorption K d values of radiosamarium in soils were strongly correlated with those of stable Sm at low concentrations (r = 0.98); indicating that the mobility of Sm radioisotopes and, thus, the risk of radioactive Sm contamination can be predicted using data from low concentrations of stable Sm. Copyright © 2017 Elsevier Ltd. All rights reserved.

Electrochemical extraction of samarium from molten chlorides in pyrochemical processes

International Nuclear Information System (INIS)

Castrillejo, Y.; Fernandez, P.; Medina, J.; Hernandez, P.; Barrado, E.

2011-01-01

This work concerns the electrochemical extraction of samarium from molten chlorides. In this way, the electrochemical behaviour of samarium ions has been investigated in the eutectic LiCl-KCl at the surface of tungsten, aluminium and aluminium coated tungsten electrodes. On a W inert electrode the electro-reduction of Sm(III) takes place in only one soluble-soluble electrochemical step Sm(III)/Sm(II). The electrochemical system Sm(II)/Sm(0) has not been observed within the electrochemical window, because of the prior reduction of Li(I) ions from the solvent, which inhibits the electro-extraction of Sm species from the salt on such a substrate. Sm metal in contact with the melt react to give Li(0) according to the reaction: Sm(0) + 2Li(I) ↔ Sm(II) + 2Li(0). On the contrary, on reactive Al electrodes the electrochemical system Sm(II)/Sm(0) was observed within the electroactive range. The potential shift of the redox couple is caused by the decrease of Sm activity in the metal phase due to the formation of Sm-Al alloys at the interface. The formation mechanism of the intermetallic compounds was studied in a melt containing: (i) both Sm(III) and Al(III) ions, using W and Al coated tungsten electrodes, and (ii) Sm(III) ions using an Al electrode. Analysis of the samples after potentiostatic electrolysis by X-ray diffraction and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), allowed the identification of Al 3 Sm and Al 2 Sm.

Electrochemical extraction of samarium from molten chlorides in pyrochemical processes

Energy Technology Data Exchange (ETDEWEB)

Castrillejo, Y., E-mail: ycastril@qa.uva.es [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Fernandez, P. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Medina, J. [Dept Fisica Materia Condensada Cristalografia y Mineralogia, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain); Hernandez, P. [Centro de Investigaciones Quimicas, Universidad Autonoma del Estado de Hidalgo, Carr. Pachuca-Tulancingo Km. 4.5, C.P. 42076 Pachuca, Hidalgo (Mexico); Barrado, E. [QUIANE/Dept Quimica Analitica, F. de Ciencias, Universidad de Valladolid, Prado de la Magdalena s/n, 47005 Valladolid (Spain)

2011-10-01

This work concerns the electrochemical extraction of samarium from molten chlorides. In this way, the electrochemical behaviour of samarium ions has been investigated in the eutectic LiCl-KCl at the surface of tungsten, aluminium and aluminium coated tungsten electrodes. On a W inert electrode the electro-reduction of Sm(III) takes place in only one soluble-soluble electrochemical step Sm(III)/Sm(II). The electrochemical system Sm(II)/Sm(0) has not been observed within the electrochemical window, because of the prior reduction of Li(I) ions from the solvent, which inhibits the electro-extraction of Sm species from the salt on such a substrate. Sm metal in contact with the melt react to give Li(0) according to the reaction: Sm(0) + 2Li(I) {r_reversible} Sm(II) + 2Li(0). On the contrary, on reactive Al electrodes the electrochemical system Sm(II)/Sm(0) was observed within the electroactive range. The potential shift of the redox couple is caused by the decrease of Sm activity in the metal phase due to the formation of Sm-Al alloys at the interface. The formation mechanism of the intermetallic compounds was studied in a melt containing: (i) both Sm(III) and Al(III) ions, using W and Al coated tungsten electrodes, and (ii) Sm(III) ions using an Al electrode. Analysis of the samples after potentiostatic electrolysis by X-ray diffraction and scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDS), allowed the identification of Al{sub 3}Sm and Al{sub 2}Sm.

Structural and luminescence properties of samarium doped lead alumino borate glasses

Science.gov (United States)

Mohan, Shaweta; Kaur, Simranpreet; Singh, D. P.; Kaur, Puneet

2017-11-01

The study reports the effect of samarium concentration on the physical, structural and spectroscopic characteristics of samarium doped lead alumino borate glasses having composition 20PbO-(10-x)Al2O3-70B2O3-xSm2O3; x = 0.1, 0.5, 1.0 and 2.0 mol %. The glasses were fabricated by conventional melt-quenching technique and then characterized by XRD, FTIR, optical absorption and fluorescence spectra. X-ray diffraction studies confirmed the amorphous nature of the prepared glasses. FTIR spectra indicate the presence of BO3, BO4, AlO6 and a few other structural groups. Various physical properties such as density, molar volume, refractive index, rare earth ion concentration, boron-boron distance and polarizability etc. were determined using conventional methods and standard formulae. The Judd-Ofelt theory was applied on the optical absorption spectra of the glasses to evaluate the three phenomenological intensity parameters Ω2, Ω4 and Ω6. The value of Ω2 was found to be highest for glass with 1 mol% Sm2O3 and attributed to the asymmetry of the ligand field at the rare earth ion site and the rare earth oxygen (Sm-O) covalency. The calculated intensity parameters and fluorescence spectra were further used to predict the radiative transition probability (A), radiative lifetime (τR), branching ratio (βR), peak wavelength (λp), effective line widths (Δλeff) and stimulated emission cross-section (σ) for the characteristic 4G5/2 → 6H5/2, 6H7/2 and 6H9/2 transitions of the Sm3+ ion. Concentration quenching was observed for 2 mol% concentration of Sm2O3 and ascribed to energy transfer through various cross-relaxation channels between Sm3+ ions. Reasonably high values of branching ratios and stimulated emission cross-section for the prepared glasses points towards their utility in the development of visible lasers emitting in the reddish-orange spectral region. However, the glass with 1 mol% Sm2O3 was found to show better radiative properties.

Resonances of coherent population trapping in samarium vapours

International Nuclear Information System (INIS)

Kolachevsky, Nikolai N; Akimov, A V; Kiselev, N A; Papchenko, A A; Sorokin, Vadim N; Kanorskii, S I

2001-01-01

Resonances of coherent population trapping were detected in atomic vapours of the rare-earth element samarium. The coherent population trapping was produced by two external-cavity diode lasers (672 and 686 nm) in a Λ-system formed by the three levels of 154 Sm: the 4f 6 6s 2 ( 7 F 0 ) ground state, the first fine-structure 4f 6 6s 2 ( 7 F 1 ) sublevel of the ground state and the 4f 6 ( 7 F)6s6p( 3 P o ) 9 F o 1 upper level. The dependence of the spectral shapes and resonance contrasts on the polarisation of the laser beams and the direction of the applied magnetic field was studied. The obtained results were analysed. (nonlinear optical phenomena)

The systems lanthanum (cerium, samarium) nitrate-tetramethyl-ammonium nitrate-water

International Nuclear Information System (INIS)

Zhuravlev, E.F.; Khisaeva, D.A.; Semenova, Eh.B.

1984-01-01

The method of cross sections at 25 and 50 deg C has been applied to study solubility in the systems lanthanum nitrate-tetramethyl ammonium nitrate-water (1), cesium (3) nitrate-tetramethyl ammonium nitrate-water (2) and samarium nitrate-tetramethyl ammonium nitrate-water (3). Crystallization fields of congruently dissolving compounds with 1:3 ratio of salt components (in system 1) and 1:2 ratio (in systems 2 and 3) are found in the systems. New solid phases are separated preparatively and subjected to chemical, differential thermal and IR spectroscopic analyses. Compositions of formed compounds are compared with the compositions known for nitrates of other representatives of light lanthanides

The systems cerium(3) (samarium) nitrate-quinoline nitrate-water

International Nuclear Information System (INIS)

Khisaeva, D.A.; Zhuravlev, E.F.; Semenova, Eh.B.

1982-01-01

Using the method of cross sections at 25 and 50 deg C the solubility in the systems cerium (3) nitrate-quinoline nitrate-water and samarium nitrate-quinoline nitrate-water has been studied. It is established that in the systems during chemical interaction of components congruently melting compounds of the composition: Ce(NO 3 ) 2 x2[C 9 H 7 NxHNO 3 ]x6H 2 O and Sm(NO 3 ) 3 x2[C 9 H 7 NxHNO 3 ]x2H 2 O are formed. New solid phases are separated preparatively and are subjected to chemical, differential thermal and IR spectroscopic analyses. The investigation results are compared with similar ones for nitrates of other representatives of lanthanide group

Samarium (III Selective Membrane Sensor Based on Tin (IV Boratophosphate

Directory of Open Access Journals (Sweden)

Ashok S. K. Kumar

2004-08-01

Full Text Available Abstract: A number of Sm (III selective membranes of varying compositions using tin (IV boratophosphate as electroactive material were prepared. Polyvinyl chloride, polystyrene and epoxy resin were used as binding materials. Membrane having composition of 40% exchanger and 60% epoxy resin exhibited best performance. This membrane worked well over a wide concentration range of 1x10-5M to 1x10-1 M of samarium ions with a Super-Nernstian slope of 40 mV/decade. It has a fast response time of less than 10 seconds and can be used for at least six months without any considerable divergence in potentials. The proposed sensor revealed good selectivities with respect to alkali, alkaline earth, some transition and rare earth metal ions and can be used in the pH range of 4.0-10.0. It was used as an indicator electrode in the potentiometric titration of Sm (III ions against EDTA. Effect of internal solution was studied and the electrode was successfully used in non-aqueous media, too.

Body composition analysis by DEXA by using dynamically changing samarium filtration

DEFF Research Database (Denmark)

Gotfredsen, Arne; Baeksgaard, L; Hilsted, J

1997-01-01

Dual-energy X-ray absorptiometry (DEXA) has a high accuracy for body composition analysis but is influenced by beam hardening and other error sources in the extremes of measurement. To compensate for beam hardening, the Norland XR-36 introduces a dynamically changing samarium filtration system......). Scans of six healthy volunteers covered with combinations of beef and lard (approximately 5-15 kg) showed a good agreement (r = 0.99) between reference and DEXA values of added soft tissue mass and fat percentage. We conclude that the DEXA method (and, in particular, the Norland XR-36 using dynamic...

Ferrites Ni0,5Zn0,5Fe2O4 doped with samarium: structural analysis, morphological and electromagnetic

International Nuclear Information System (INIS)

Costa, A.C.F.M.; Diniz, A.P.; Viana, K.M.S.; Cornejo, D.R.; Kiminami, R.H.G.A.

2010-01-01

This paper proposes to investigate the sintering at 1200 deg C/2h of Ni 0.5 Zn 0.5 Fe 2-x Sm x O 4 ferrite doped with 0.05; 0.075 e 0.1 mol of Sm synthesized by combustion reaction to evaluate the performance materials as absorbers of electromagnetic radiation. The influence of the concentration of samarium on the structure, morphology and electromagnetic properties of ferrites was studied. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), magnetic measurements and reflectivity measurements in the frequency range between 8-12 GHz. The results showed that increasing the concentration of samarium caused a decrease in particle size of the samples, encouraging, therefore, to obtain materials with better values of magnetization and reflectivity, allowing for use as absorbers in narrow-band frequency between 9-10 GHz. (author)

The effectiveness of samarium-153 (153Sm) lexidronam (EDTMP) in treatment of bone metastases

International Nuclear Information System (INIS)

Ma Yubo; Huang Gang; Liu Jianjun

2004-01-01

Objectives: To evaluate the effectiveness of samarium-153 (153Sm) lexidronam (EDTMP) in treatment of bone metastases. Methods: 380 patients with bone metastases were studied (221 men, 159 women; average age 65.3 y; ranged 27-91 y; average weight 59.3 kg, ranged 39-95 kg). The tumor types were prostate carcinoma (n=155), pulmonary carcinoma (n=92), breast cancer (n=57), gastric carcinoma (n=12), colorectal carcinoma (n=22), nasopharyngeal carcinoma (n=8), lymphoma (n=8), hepatic carcinoma (n=6), ovary carcinoma (n=4) and others (n=16). All patients were received 135Sm-EDTMP 0.8 or 1.0 mCi/kg during 1 to 7 course of treatment. Patients and physician evaluations were used to assess pain relief. Numbers of metastatic foci and activity of ROIs were used to observe post-therapy change in bone scanning. Results: In 380 patients, pain relief was observed in 257 patients (67.6%). Persistence of pain relief was seen through 2 to 24 weeks. The mean relief time is 5.8±3.4 weeks. KPS score was higher 10% than pre-therapy (71.2%±9.6% Vs 80.9%±10.3%, p<0.001). Numbers of metastatic foci (11.2+8.8 Vs 8.4±5.7, p<0.001) and activity of ROIs (3.28±2.04 Vs 2.15±0.94, p<0.01) were less than pre-therapy. Bone marrow suppression was mild and reversible (5.87±1.56 Vs 4.94±1.16 x 109/L). Conclusions: 153Sm-EDTMP provided relief of pain associated with bone metastases and inhibition of metastatic foci. As a relief drug of painful bone metastases, 153Sm-EDTMP is safe and effective. (authors)

Fluorometric determination of samarium and europium in rare earth minerals with. beta. -diketoneternary complex

Energy Technology Data Exchange (ETDEWEB)

Huang, H; Hiraki, K; Nishikawa, Y [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1981-07-01

This communication reported the optimum conditions for the fluorometric determination of these ions, and the method was adopted in the simultaneous determination of samarium and europium in xenotime and monazite minerals. From the experimental results on the effect of diverse ions and the extraction pH of the aqueous phase, it became clear that TTA-TOPO hexane method was the best system for the determination of samarium and europium because of the highest fluorescence sensitivity of the ternary complex, and also because the lower extraction pH eliminated the effect of diverse ions. Moreover, the very high detection limit (2 ppb) of Sm was achieved by the use of a red sensitive photomultiplier. Which was used at 644 nm, and that of Eu (0.02 ppb) at 614 nm. The procedure was established as follows: The rare earth minerals (xenotime, monazite) sample was treated with hot conc. H/sub 2/SO/sub 4/ and twice precipitated with 0.5 mol dm/sup -3/ oxalic acid (pH was adjusted to 2.0 -- 2.2). Then the precipitate was filtered and ignited to give the rare earth oxide. Fifty milligrams of the oxide was dissolved in HCl and diluted with water in order to obtain the solution containing 5 ..mu..g cm/sup -3/ rare earth oxide. An aliquot of the solution ((1.0 -- 3.0) cm/sup 3/) was adjusted to pH 5.5 with sodium acetate and shaken with 1 x 10/sup -4/ mol dm/sup -3/ TTA- 2 x 10/sup -2/ mol dm/sup -3/ TOPO hexane solution. Then the fluorescence intensity of the organic layer was measured at 644 nm for Sm and 614 nm for Eu. In this procedure, the recovery of Sm and Eu was found to be about 96%. Xenotime contained 0.70% of Sm and 0.004% of Eu, and monazite contained 1.84% of Sm and 0.003% of Eu.

Effect of Zinc Oxide Doping on Electroluminescence and Electrical Behavior of Metalloporphyrins-Doped Samarium Complex

Science.gov (United States)

Janghouri, Mohammad; Amini, Mostafa M.

2018-02-01

Samarium complex [(Sm(III)] as a new host material was used for preparation of red organic light-emitting diodes (OLEDs). Devices with configurations of indium-doped tin oxide (ITO)/poly(3,4-ethylenedioxythiophene):(poly(styrenesulfonate) (PEDOT:PSS (50 nm)/polyvinyl carbazole (PVK):[zinc oxide (ZnO)] (50 nm)/[(Sm(III)]:[zinc(II) 2,3-tetrakis(dihydroxyphenyl)-porphyrin and Pt(II) 2,3-dimethoxyporphyrin] (60 nm)/2,9-dimethyl-4,7-diphenyl-1,10-phenanthroline (BCP) (15 nm)/Al (150 nm) have been fabricated and investigated. An electroplex occurring at the (PVK/Sm: Pt(II) 2,3-dimethoxyporphyrin) interface has been suggested when ZnO nanoparticles were doped in PVK. OLED studies have revealed that the photophysical characteristics and electrical behavior of devices with ZnO nanoparticles are much better than those of devices with pure PVK. The efficiency of devices based on [(Sm(III)] was superior than that of known aluminum tris(8-hydroxyquinoline) (Alq3) and also our earlier reports on red OLEDs under the same conditions.

Determination of micro amounts of samarium and europium by analogue derivative spectrophotometry

International Nuclear Information System (INIS)

Ishii, H.; Satoh, K.

1982-01-01

Derivative spectrophotometry using the analogue differentiation circuit was applied to the determination of samarium and europium at ppm levels. By measuring the second or the fourth derivative spectra of the characteristic absorption bands of both the rare earth ions around 400 nm, they can be determined directly and selectively in the presence of large amounts of most other rare earths without any prior separation. Further, aptly selecting conditions for the measurement of the derivative spectra, the simultaneous determination of both the rare earth elements was feasible. The principle and the characteristics of analogue derivative spectrophotometry are also described. (orig.) [de

Enhancement of the fluorescence of the samarium (III) complex by gadolinium (III)

International Nuclear Information System (INIS)

Yun-Xiang, C.; Zhang-Hua, L.

1988-01-01

The increase in sensitivity and selectivity of reactions in which colored species are formed by the addition of different metal ions is an area of research that has recently been developed. This phenomenon, which is sometimes called cocolaration effect, has been explained by the formation of mixed metal complex. The authors found an analogous phenomenon of reactions forming fluorescent complexes. The complexes of Sm(III)-thenoyltrifluoroacetone (TTA)-phenanthroline (Phen)-Triton-X-100 (TX-100) and Gd(III) (or La(III), Lu(III) and Y(III))-TTA-Phen-TX-100 had practically no fluorescence separately. Instead, a fluorescence-enhancement phenomenon caused by adding Gd or La, Lu and Y ions to the system was observed for the first time. The intensity of the enhanced fluorescence of Sm(III) complex was increased in the following order: La< Y< Lu< Gd. By analogy with cocoloration effect, the authors call this new fluorescence-enhancement phenomenon the co-fluorescence effect. The object of this work was to study the enhancement effect of Gd(III) on the fluorescence of the Sm(III)-TTA-Phen-TX-100 system. The recommended fluorimetric method has been applied to the determination of trace amounts of samarium in ytterbium oxide with satisfactory results. A general reaction mechanism for the system studied was proposed

New reduced variant in gadolinium and samarium monoxide thin films

Energy Technology Data Exchange (ETDEWEB)

Bist, B M.S.; Kumar, J; Srivastava, O N [Banaras Hindu Univ. (India). Dept. of Physics

1977-01-01

A new reduced phase has been observed in the thin films of gadolinium and samarium monoxides. This phase results on imparting an annealing treatment to the monoxides and is formed as a result of the creation and ordering of vacancies in the oxygen sublattice. The new phase has been analysed to possess a rhombohedral unit cell with lattice parameters a/sub R/ = a/sub 0/ square root of (3/2) and c/sub R/ = a/sub 0/ square root of 3 (based on hexagonal axes, a/sub 0/ being the lattice parameter of the fundamental zinc blende type unit cell of the monoxide). Based on the proposed structure, the new phase can be assigned the solid state chemical formula RO/sub x/ where R = Gd, Sm and x = 0.66.

Enhanced electron-lattice coupling under uniaxial stress in layered double hydroxides intercalated with samarium complexes

International Nuclear Information System (INIS)

Park, Ta-Ryeong

2004-01-01

We have applied uniaxial stress to samarium complexes by intercalating them into the gallery of a layered material and by using a diamond-anvil cell at 28 K. Although uniaxial stress reduces symmetry and removes degeneracy, the overall number of photoluminescence (PL) peaks evidently decreased with the application of uniaxial stress. This contradictory observation is explained by an increased electron-lattice coupling strength under uniaxial stress. This behavior is also confirmed by time-resolved PL data.

Evaluation of samarium-153 and holmium-166-EDTMP in the normal baboon model

Energy Technology Data Exchange (ETDEWEB)

Louw, W.K.A.; Dormehl, I.C.; Rensburg, A.J. van; Hugo, N.; Alberts, A.S.; Forsyth, O.E.; Beverley, G.; Sweetlove, M.A.; Marais, J.; Loetter, M.G.; Aswegen, A. van

1996-11-01

Bone-seeking radiopharmaceuticals such as ethylenediaminetetramethylene phosphonate (EDTMP) complexes of samarium-153 and holmium-166 are receiving considerable attention for therapeutic treatment of bone metastases. In this study, using the baboon experimental model, multicompartmental analysis revealed that with regard to pharmacokinetics, biodistribution, and skeletal localisation, {sup 166}Ho-EDTMP was significantly inferior to {sup 153}Sm-EDTMP and {sup 99m}Tc-MDP. A more suitable {sup 166}Ho-bone-seeking agent should thus be sought for closer similarity to {sup 153}Sm-EDTMP to exploit fully the therapeutic potential of its shorter half-life and more energetic beta radiation.

Performance analysis of samarium cobalt P.M. synchronous motor fed from PWM inverters

International Nuclear Information System (INIS)

Rahman, M.A.; Choudhury, M.A.

1985-01-01

This paper presents an analysis and performance of samarium cobalt permanent magnet (P.M.) synchronous motors fed from two types of voltage source pulse width modulated (PWM) inverters. The analysis and test results on the steady state performance of a P.M. motor fed from PWM inverters are presented. PWM inverters are used in variable voltage variable frequency applications to avoid a double conversion process of ordinary inverters. In drives, they are used for voltage and speed regulation of motors. Use of modulation technique in inverters also allow to eliminate or minimize selected harmonics from the inverter output voltage

JAEA thermodynamic database for performance assessment of geological disposal of high-level and TRU wastes. Refinement of thermodynamic data for trivalent actinoids and samarium

International Nuclear Information System (INIS)

Kitamura, Akira; Fujiwara, Kenso; Yui, Mikazu

2010-01-01

Within the scope of the JAEA thermodynamic database project for performance assessment of geological disposal of high-level radioactive and TRU wastes, the refinement of the thermodynamic data for the inorganic compounds and complexes of trivalent actinoids (actinium(III), plutonium(III), americium(III) and curium(III)) and samarium(III) was carried out. Refinement of thermodynamic data for these elements was based on the thermodynamic database for americium published by the Nuclear Energy Agency in the Organisation for Economic Co-operation and Development (OECD/NEA). Based on the similarity of chemical properties among trivalent actinoids and samarium, complementary thermodynamic data for their species expected under the geological disposal conditions were selected to complete the thermodynamic data set for the performance assessment of geological disposal of radioactive wastes. (author)

Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues

International Nuclear Information System (INIS)

Garcia G, N.

2006-01-01

Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH PCN ) and density of surface sites (D s ). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

Optical properties and electronic transitions of zinc oxide, ferric oxide, cerium oxide, and samarium oxide in the ultraviolet and extreme ultraviolet

DEFF Research Database (Denmark)

Pauly, N; Yubero, F; Espinós, J P

2017-01-01

Optical properties and electronic transitions of four oxides, namely zinc oxide, ferric oxide, cerium oxide, and samarium oxide, are determined in the ultraviolet and extreme ultraviolet by reflection electron energy loss spectroscopy using primary electron energies in the range 0.3-2.0 ke...

Magnetic behavior study of samarium nitride using density functional theory

Science.gov (United States)

Som, Narayan N.; Mankad, Venu H.; Dabhi, Shweta D.; Patel, Anjali; Jha, Prafulla K.

2018-02-01

In this work, the state-of-art density functional theory is employed to study the structural, electronic and magnetic properties of samarium nitride (SmN). We have performed calculation for both ferromagnetic and antiferromagnetic states in rock-salt phase. The calculated results of optimized lattice parameter and magnetic moment agree well with the available experimental and theoretical values. From energy band diagram and electronic density of states, we observe a half-metallic behaviour in FM phase of rock salt SmN in while metallicity in AFM I and AFM III phases. We present and discuss our current understanding of the possible half-metallicity together with the magnetic ordering in SmN. The calculated phonon dispersion curves shows dynamical stability of the considered structures. The phonon density of states and Eliashberg functional have also been analysed to understand the superconductivity in SmN.

Preparation and biological behaviour of samarium-153-hydroxyapatite particles for radiation synovectomy

International Nuclear Information System (INIS)

Agrueelles, M.G.; Luppi Berlanga, I.S.; Torres, E.A.; Rutty Sola, G.A.; Rimoldi, G.

1998-01-01

The preparation and labelling procedures of 153 Sm-hydroxyapatite ( 153 Sm-HA) are described in this paper. Hydroxyapatite (HA) was prepared and studied as a radiosynovectomy agent. HA particles were prepared from the reaction of calcium nitrate and ammonia phosphate at high pH Samarium-153 labelling was done in two steps with citric acid. A serie of experimental conditions, such as specific activity, citric acid mass, radioactive solution volume, in-vitro stability, have been carried out. Radiolabelling efficiency was greater than 95%. In vitro studies showed high stability (≥99%). Animal studies showed a good retention in the synovium, with a very low extra-articular leakage over 6 days after administration. (author)

Fabrication of a PVC membrane samarium(III) sensor based on N,N′,N″-tris(4-pyridyl)trimesic amide as a selectophore

International Nuclear Information System (INIS)

Zamani, Hassan Ali; Naghavi-Reyabbi, Fatemeh; Faridbod, Farnoush; Mohammadhosseini, Majid; Ganjali, Mohammad Reza; Tadjarodi, Azadeh; Rad, Maryam

2013-01-01

A new ion-selective electrode for Sm 3+ ion is described based on the incorporation of N,N′,N″-tris(4-pyridyl)trimesic amide (TPTA) in a poly(vinylchloride) (PVC) matrix. The membrane sensor comprises nitrobenzene (NB) as a plasticizer, and oleic acid (OA) as an anionic additive. The sensor with the optimized composition shows a Nernstian potential response of 19.8 ± 0.5 mV decade −1 over a wide concentration range of 1.0 × 10 −2 and 1 × 10 −6 mol L −1 , with a lower detection limit of 4.7 × 10 −7 mol L −1 and satisfactor applicable pH range of 3.6–9.2. Having a short response time of less than 10 s and a very good selectivity towards the Sm 3+ over a wide variety of interfering cations (e.g. alkali, alkaline earth, transition and heavy metal ions) the sensor seemed to be a promising analytical tool for determination of the Sm 3+ . Hence, it was used as an indicator electrode in the potentiometric titration of samarium ion with EDTA. It was also applied to the direct samarium recovery in binary mixtures. - Highlights: ► A new Sm 3+ -PVC membrane sensor is introduced for determination of Sm 3+ ions in the solutions. ► N,N′,N″-tris(4-pyridyl)trimesic amide was used as a suitable selectophore for samarium sensor. ► Detection limit of the sensor is 4.7 × 10 −7 mol L −1 with a short response time of less than 10 s.

Optical and physical properties of samarium doped lithium diborate glasses

Science.gov (United States)

Hanumantharaju, N.; Sardarpasha, K. R.; Gowda, V. C. Veeranna

2018-05-01

Sm3+ doped lithium di-borate glasses with composition 30Li2O-60B2O3-(10-x) PbO, (where 0 molar volume with samarium ion content indicates the openness of the glass structure. The gradual increase in average separation of boron-boron atoms with VmB clearly indicates deterioration of borate glass network, which in turn leads to decrease in the oxygen packing density. The replacements of Sm2O3 for PbO depolymerise the chain structure and that would increase the concentration of non-bridging oxygens. The marginal increase of optical band gap energy after 1.0 mol.% of Sm2O3 is explained by considering the structural modification in lead-borate. The influence of Sm3+ ion on physical and optical properties in lithium-lead-borate glasses is investigated and the results were discussed in view of the structure of borate glass network.

Pyroelectric properties and electrical conductivity in samarium doped BiFeO 3 ceramics

KAUST Repository

Yao, Yingbang

2012-06-01

Samarium (Sm 3+) doped BiFeO 3 (BFO) ceramics were prepared by a modified solid-state-reaction method which adopted a rapid heating as well as cooling during the sintering process. The pyroelectric coefficient increased from 93 to 137 μC/m 2 K as the Sm 3+ doping level increased from 1 mol% to 8 mol%. Temperature dependence of the pyroelectric coefficient showed an abrupt decrease above 80 °C in all samples, which was associated with the increase of electrical conductivity with temperature. This electrical conduction was attributed to oxygen vacancy existing in the samples. An activation energy of ∼0.7 eV for the conduction process was found to be irrespective of the Sm 3+ doping level. On the other hand, the magnetic Néel temperature (T N) decreased with increasing Sm 3+ doping level. On the basis of our results, the effects of Sm doping level on the pyroelectric and electrical properties of the BFO were revealed. © 2011 Elsevier Ltd. All rights reserved.

Preparation and examination of properties of samarium-153-EDTMP complex; Otrzymywanie chelatu kwasu etylenodiaminotetrametylenofosfonowego (EDTMP) z samarem-153 i badanie jego wlasciwosci

Energy Technology Data Exchange (ETDEWEB)

Nowak, M. [Institute of Atomic Energy, Otwock-Swierk (Poland); Garnuszek, P.; Lukasiewicz, A.; Wozniak, I.; Zulczyk, W. [Osrodek Badawczo-Rozwojowy Izotopow, Otwock-Swierk (Poland); Licinska, I. [Instytut Lekow, Warsaw (Poland)

1995-12-31

Preparation and properties of ethylenediaminetetramethylenephosphonic acid (EDTMP) as well as some properties of {sup 153}Sm-EDTMP chelate have been examined. The chelate formed by samarium-153 (46.3 h, {beta}{sup -}-decay) with EDTMP exhibits high bone uptake and can be used for treatment of disseminated, painful skeletal metastases. The purity and stability of solutions of {sup 153}Sm-EDTMP chelate were examined in a broad range of samarium concentration and {sup 153}Sm specific activity. The complex under study was examined by radio-TLC, -electrophoresis and radio-HPLC. The results obtained suggest the small size of molecules of {sup 153}Sm-EDTMP chelate as compared with molecules of ``free``EDTMP. The results of biodistribution of {sup 153}Sm-EDTMP determined in rats indicate the quick blood clearance, high deposition of radioactivity in bone and quick excretion of radioactivity into urine. No specific uptake of {sup 153}Sm-EDTMP in extra-skeletal organs was found. (author). 42 refs, 13 figs, 22 tabs.

Results after therapy of pain from bone metastases with Samarium-153 in our centers in Lima, Peru

International Nuclear Information System (INIS)

Alvarado, N.; Eskenazi, S.; Valle, M.P.; Montoya, J.; Castro, M.; Montiel, L.; Velarde, V.; Jauregui, I.; Cueto, C.

2004-01-01

Full text: 105 patients with bone metastases from prostate and breast cancer; between 42 and 78 years age (median 61 years) were evaluated. Patients had intense pain that could not be managed with combinations of analgesic and anti tumoral drugs. All patients received 1.2 mCi/kg of Samarium-153 intravenously as treatment for pain due to bony metastases. The isotope obtained from atomic reactor placed in Lima - Peru, was provided by Peruvian Nuclear Energy Institute (IPEN). One week before therapy, all the patients had a bone scan study with Tc99m-MDP that showed the presence of multiple bone metastases with high blastic activity. Haematology and biochemical parameter checked were: Creatinine ( 150,000 mm3), Leukocytes (> 5,000 mm3), Red cells (>3,500,000 mm3). No problems were encountered during intravenous administration of the radioisotope. The side effects after treatment were: Primary effects: 16 cases of nausea, 2 of vomiting, 3 of headache, 28 had increment of pain, 6 had flushing. 50 patients did not have the primary symptoms. Secondary effects: 3 Patients showed drop in leukocyte count between 2nd and 3rd week of therapy. Red cells showed 10-15% decrease between 6th to 8th week. Platelets showed a decrease of about 15% with one peak between 1st and 2nd week post Samarium therapy. Data was analysed using an analogue visual scale of the pain with values from 0 - 10 (0-no pain; 10-maximum pain) and in the same way using the E.C.O.G. scale (Eastern Cooperative Oncology Group) in relationship with the Karnofsky index in order to establish functional recovery for each patient. The decrease of pain was seen between 4th-7th days (average 8 days). A second dose was given after 60 days in 12 patients and a third dose in 3 cases.11 patients died due to different causes between 30 - 60 days post treatment. The analgesic dose came down significantly in 80% of patients. We conclude that palliative therapy of metastatic bone pain in Peru is possible with radionuclides. It

Potentiometric study of samarium oxides formation from its chloride in a molten eutectic mixture of sodium and cesium chlorides

International Nuclear Information System (INIS)

Smolenskij, V.V.; Bove, A.L.; Del'mukhamedov, R.D.; Borodina, N.P.; Gavrilov, A.G.

1997-01-01

Interaction of trivalent samarium cations with oxide-ions in NaCl-2CsCl melt at 973 K has been studied by potentiometric method using electrochemical cell with two platinum-oxygen electrodes with a solid electrolyte membrane. The mechanism of the interaction and composition of the reaction products, depending on the medium oxyacidity, have been considered. Certain thermodynamic characteristics of the process have been calculated

Structural phase transition and electronic properties in samarium chalcogenides

Energy Technology Data Exchange (ETDEWEB)

Panwar, Y. S., E-mail: yspanwar2011@gmail.com [Department of Physics, Govt. New Science College Dewas-455001 (India); Aynyas, Mahendra [Department of Physics, C.S.A. Govt. P.G. College, Sehore, 466001 (India); Pataiya, J.; Sanyal, Sankar P. [Department of Physics, Barkatullah University, Bhopal, 462026 (India)

2016-05-06

The electronic structure and high pressure properties of samarium monochalcogenides SmS, SmSe and SmTe have been reported by using tight binding linear muffin-tin-orbital (TB-LMTO) method within the local density approximation (LDA). The total energy as a function of volume is evaluated. It is found that these monochalcogenides are stable in NaCl-type structure under ambient pressure. We predict a structural phase transition from NaCl-type (B{sub 1}-phase) structure to CsCl-type (B{sub 2}-type) structure for these compounds. Phase transition pressures were found to be 1.7, 4.4 and 6.6 GPa, for SmS, SmSe and SmTe respectively. Apart from this, the lattice parameter (a{sub 0}), bulk modulus (B{sub 0}), band structure (BS) and density of states (DOS) are calculated. From energy band diagram we observed that these compounds exhibit metallic character. The calculated values of equilibrium lattice parameter and phase transition pressure are in general good agreement with available data.

Effects of increasing doses of samarium-153-ethylenediaminetetramethylene phosphonate on axial and appendicular skeletal growth in juvenile rabbits

Energy Technology Data Exchange (ETDEWEB)

Essman, Stephanie C. [Department of Veterinary Medicine and Surgery, College of Veterinary Medicine, University of Missouri-Columbia, Columbia, MO 65211 (United States)], E-mail: essmans@missouri.edu; Lewis, Michael R. [Department of Veterinary Medicine and Surgery, College of Veterinary Medicine, University of Missouri-Columbia, Columbia, MO 65211 (United States); Department of Radiology, University of Missouri-Columbia, Columbia, MO 65211 (United States); Nuclear Science and Engineering Institute, University of Missouri-Columbia, Columbia, MO 65211 (United States); Research Service, Harry S. Truman Memorial Veterans' Hospital, Columbia, MO 65201 (United States); Fox, Derek B. [Department of Veterinary Medicine and Surgery, College of Veterinary Medicine, University of Missouri-Columbia, Columbia, MO 65211 (United States)

2008-02-15

Introduction: Targeted radiotherapy using samarium-153-ethylenediaminetetramethylene phosphonate ({sup 153}Sm-EDTMP) is currently under investigation for treatment of osteosarcoma. Osteosarcoma often occurs in children, and previous studies on a juvenile rabbit model demonstrated that clinically significant damage to developing physeal cartilage may occur as a result of systemic {sup 153}Sm-EDTMP therapy. The aim of this study was to evaluate the late effects of {sup 153}Sm-EDTMP on skeletal structures during growth to maturity and to determine if there is a dose response of {sup 153}Sm-EDTMP on growth of long bones. Methods: Female 8-week-old New Zealand white rabbits were divided into three treatment groups plus controls. Each rabbit was intravenously administered a predetermined dose of {sup 153}Sm-EDTMP. Multiple bones of each rabbit were radiographed every 2 months until physeal closure, with subsequent measurements made to assess for abbreviated bone growth. Statistical analyses were performed to determine the differences in bone length between groups, with significance set at P<.05. Results: Significant differences in lengths of multiple bones were detected between the high-dose group and other treatment groups and controls at each time interval. A significant difference in lengths of the tibias was also noted in the medium-treatment group, compared to controls. Mean reduction of bone length was first detected at 4 months and did not increase significantly over time. Conclusions: These data suggest that clinically significant bone shortening may occur as a result of high-dosage administration of {sup 153}Sm-EDTMP. Further investigation regarding the effects of bone-seeking radiopharmaceuticals on bone growth and physeal cartilage is warranted.

Effect of samarium (Sm) addition on the microstructures and mechanical properties of Al–7Si–0.7Mg alloys

International Nuclear Information System (INIS)

Qiu, Hongxu; Yan, Hong; Hu, Zhi

2013-01-01

Highlights: •Sm affected the secondary dendrite arm spacing of Al–7Si–0.7Mg alloy. •The coarse plate-like eutectic silicon was fully modified into a fine branched and particle structure when 0.6 wt.% Sm added. •The tensile properties were enhanced by the addition of Sm. •Sm has marked effects on eutectic temperature and the latent heat ΔH R on remelting behavior. •The morphology and chemical composition of Sm-rich intermetallics were studied. -- Abstract: The effects of samarium (Sm) additions (0–0.9 wt.%) on the microstructures and mechanical properties of Al–7Si–0.7Mg alloys have been studied in this article. The microstructures of the as-cast samples were examined by optical microscopy (OM) and scanning electron microscopy (SEM). The experimental results indicated that the rare earth Sm affected the secondary dendrite arm spacing (SDAS) of Al–7Si–0.7Mg alloy. And it was found that Sm had great modification effects on the microstructures of eutectic silicon. When 0.6 wt.% Sm was added to the alloy, the coarse plate-like eutectic silicon was fully modified into a fine fibrous structure; the dendrites of Al–7Si–0.7Mg alloy was best refined. The mechanical properties were investigated by tensile test. The findings indicate that the tensile properties and elongation were improved by the addition of Sm. And a good combination of ultimate tensile strength (215 MPa) and elongation (3.3%) was obtained when the Sm addition was up to 0.6 wt.%. Furthermore the results of thermal analysis reveal that Sm addition had marked effects on eutectic temperature and the latent heat ΔH R on remelting behavior

Sorption of samarium in iron (II) and (III) phosphates in aqueous systems; Sorcion de samario en fosfatos de hierro (II) y (III) en sistemas acuosos

Energy Technology Data Exchange (ETDEWEB)

Diaz F, J C

2006-07-01

The radioactive residues that are stored in the radioactive confinements its need to stay isolated of the environment while the radioactivity levels be noxious. An important mechanism by which the radioactive residues can to reach the environment, it is the migration of these through the underground water. That it makes necessary the investigation of reactive materials that interacting with those radionuclides and that its are able to remove them from the watery resources. The synthesis and characterization of materials that can be useful in Environmental Chemistry are very important because its characteristics are exposed and its behavior in chemical phenomena as the sorption watery medium is necessary to use it in the environmental protection. In this work it was carried out the sorption study of the samarium III ion in the iron (II) and (III) phosphate; obtaining the sorption isotherms in function of pH, of the phosphate mass and of the concentration of the samarium ion using UV-visible spectroscopy to determine the removal percentage. The developed experiments show that as much the ferrous phosphate as the ferric phosphate present a great affinity by the samarium III, for what it use like reactive material in contention walls can be very viable because it sorption capacity has overcome 90% to pH values similar to those of the underground and also mentioning that the form to obtain these materials is very economic and simple. (Author)

Separation of lanthanum from samarium on solid aluminum electrode in LiCl-KCl eutectic melts

International Nuclear Information System (INIS)

De-Bin Ji; Mi-Lin Zhang; Xing Li; Xiao-Yan Jing; Wei Han; Yong-De Yan; Yun Xue; Zhi-Jian Zhang; Harbin Engineering University, Harbin

2015-01-01

This paper presents an electrochemical study on the separation of lanthanum from samarium on aluminum electrode at 773 K. The results from different electrochemical methods showed that Sm(III) and La(III) formed Al-Sm and Al-La intermetallic compounds on an aluminum electrode at electrode potential around -1.67 and -1.46 V, respectively. The electrochemical separation of lanthanum was carried out in LiCl-KCl-LaCl 3 -SmCl 3 melts on solid aluminum electrodes at 773 K by potentiostatic electrolysis at -1.45 V for 40 h and the separation efficiency was 99.1 %. (author)

Europium and samarium doped calcium sulfide thin films grown by PLD

International Nuclear Information System (INIS)

Christoulakis, S.; Suchea, M; Katsarakis, N.; Koudoumas, E

2007-01-01

Europium and samarium doped calcium sulfide thin films (CaS:Eu,Sm) with different thickness were prepared by the pulsed laser deposition technique using sintered targets. A typical homemade deposition chamber and XeCl excimer laser (308 nm) were employed and the films were deposited in helium atmosphere onto silicon and corning glass substrates. Structural investigations carried out by X-ray diffraction and atomic force microscopy showed a strong influence of the deposition parameters on the film properties. The films grown had an amorphous or polycrystalline structure depending on growth temperature and the number of pulses used, the same parameters affecting the film roughness, the grain shape and dimensions, the film thickness and the optical transmittance. This work indicates that pulsed laser deposition can be a suitable technique for the preparation of CaS:Eu,Sm thin films, the film characteristics being controlled by the growth conditions

The dynamics of the laser-induced metal-semiconductor phase transition of samarium sulfide (SmS)

International Nuclear Information System (INIS)

Kaempfer, Tino

2009-01-01

The present thesis is dedicated to the experimental study of the metal-semiconductor phase transition of samarium sulfide (SmS): Temperature- and time-resolved experiments on the characterization of the phase transition of mixed-valence SmS samples (M-SmS) are presented. The measurement of the dynamics of the laser-induced phase transition pursues via time-resolved ultrashort-time microscopy and by X-ray diffraction with sub-picosecond time resolution. The electronic and structural processes, which follow an excitation of M-SmS with infrared femtosecond laser pulses, are physically interpreted on the base of the results obtained in this thesis and model imaginations. [de

Determination of trace amounts of rare earth elements in samarium, terbium and disprosium oxides by graphite furnace atomic-absorption spectrometry

International Nuclear Information System (INIS)

Dantas, E.S.K.

1990-01-01

A graphite furnace atomic-absorption spectrometry method for the determination of neodymium, europium, terbium, dysprosium and yttrium at trace level in samarium oxide; of samarium, europium, dysprosium, holmium, erbium and yttrium in terbium oxide and of europium, terbium, holmium, erbium and yttrium in dysprosium oxide was established. The best pyrolysis and atomization temperatures were determined for each lanthanide considered. Calibration curves were obtained for the pure elements, for binary mixtures formed by the matrix and each of the lanthanides studied and, finally, for the complex mixtures constituted by the matrix and all the other lanthanide of the group under scrutiny. This study has been carried out to examine the interference of the presence of one lanthanide on the behaviour of the other, since a lack of linearity on the calibration curves has been observed in some cases. Detection and determination limits have been determined as well. The detection limits encountered were within the range 0.002 to 0.3% for different elements. The precision of the method expressed as the relative standard deviation was calculated for each element present in each of the matrices studied. The conclusion arrived at is that the method can be applied for determining the above mentioned lanthanides present in the matrices studied with purity up to 99.50%. (author)

Synthesis of samarium complexes with the derivative binder of Schiff Quinolinic base. Characterization and photophysical study; Sintesis de complejos de samario con el ligante derivado de base de Schiff Quinolinica. Caracterizacion y estudio fotofisico

Energy Technology Data Exchange (ETDEWEB)

Lucas H, J.

2016-07-01

In this work we determined the metal: binder stoichiometry of the species formed during the UV/Vis spectrophotometric titration of the derivative binder of Schiff quinolinic base, L1 with the samarium nitrate pentahydrate in methanol. Statistical analysis of the data allowed proposing the metal: binder stoichiometry for the synthesis of the complexes which was one mole of samarium salt by 2.5 moles of binder and thus favor the formation of complexes with 1M: 1L and 1M: 2L stoichiometries. They were synthesized in aqueous-organic medium (water-ethanol), isolated and purified two complexes with stoichiometry 1 Sm: 1 L1, complex 1 and 1 Sm: 2 L1, complex 2. The overall yield of the reaction was 76%. The characterization of the formed complexes was performed by visible ultraviolet spectrometry (UV/Vis), nuclear magnetic resonance, X-ray photoelectron spectroscopy (XP S), thermal gravimetric analysis with differential scanning calorimetry (TGA/DSC), and radial distribution function. These complexes were studied by fluorescence and emission phosphorescence at variable temperature. Spectroscopic techniques used in both solution and solid demonstrated the formation and stability of these complexes. In addition XP S indicated that in both complexes the samarium retains its oxidation state 3+. Luminescence studies indicated that there is intra-binding charge transfer which decreases the transfer of light energy from the binder to the samarium. Based on the experimental results, L1 binder molecules and complexes 1 and 2 were modeled that demonstrated the proposed Nc for each complex, as well as allowed to visualize the structural arrangement of the molecules, complexes and binder. (Author)

Fabrication of a PVC membrane samarium(III) sensor based on N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide as a selectophore

Energy Technology Data Exchange (ETDEWEB)

Zamani, Hassan Ali, E-mail: haszamani@yahoo.com [Department of Applied Chemistry, Mashhad Branch, Islamic Azad University, Mashhad (Iran, Islamic Republic of); Naghavi-Reyabbi, Fatemeh [Resident of General Surgery, Endoscopic and Minimaly Invasive Surgery Research Center, Ghaem Hospital, Faculty of Medicine, Mashhad University of Medical Sciences, Mashhad (Iran, Islamic Republic of); Faridbod, Farnoush [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Mohammadhosseini, Majid [Department of Chemistry, Faculty of Basic Sciences, Shahrood Branch, Islamic Azad University, Shahrood (Iran, Islamic Republic of); Ganjali, Mohammad Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Tadjarodi, Azadeh; Rad, Maryam [Department of Chemistry, Iran University of Science and Technology, Tehran (Iran, Islamic Republic of)

2013-03-01

A new ion-selective electrode for Sm{sup 3+} ion is described based on the incorporation of N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide (TPTA) in a poly(vinylchloride) (PVC) matrix. The membrane sensor comprises nitrobenzene (NB) as a plasticizer, and oleic acid (OA) as an anionic additive. The sensor with the optimized composition shows a Nernstian potential response of 19.8 {+-} 0.5 mV decade{sup -1} over a wide concentration range of 1.0 Multiplication-Sign 10{sup -2} and 1 Multiplication-Sign 10{sup -6} mol L{sup -1}, with a lower detection limit of 4.7 Multiplication-Sign 10{sup -7} mol L{sup -1} and satisfactor applicable pH range of 3.6-9.2. Having a short response time of less than 10 s and a very good selectivity towards the Sm{sup 3+} over a wide variety of interfering cations (e.g. alkali, alkaline earth, transition and heavy metal ions) the sensor seemed to be a promising analytical tool for determination of the Sm{sup 3+}. Hence, it was used as an indicator electrode in the potentiometric titration of samarium ion with EDTA. It was also applied to the direct samarium recovery in binary mixtures. - Highlights: Black-Right-Pointing-Pointer A new Sm{sup 3+}-PVC membrane sensor is introduced for determination of Sm{sup 3+} ions in the solutions. Black-Right-Pointing-Pointer N,N Prime ,N Double-Prime -tris(4-pyridyl)trimesic amide was used as a suitable selectophore for samarium sensor. Black-Right-Pointing-Pointer Detection limit of the sensor is 4.7 Multiplication-Sign 10{sup -7} mol L{sup -1} with a short response time of less than 10 s.

Solar Hydrogen Production via a Samarium Oxide-Based Thermochemical Water Splitting Cycle

Directory of Open Access Journals (Sweden)

Rahul Bhosale

2016-04-01

Full Text Available The computational thermodynamic analysis of a samarium oxide-based two-step solar thermochemical water splitting cycle is reported. The analysis is performed using HSC chemistry software and databases. The first (solar-based step drives the thermal reduction of Sm2O3 into Sm and O2. The second (non-solar step corresponds to the production of H2 via a water splitting reaction and the oxidation of Sm to Sm2O3. The equilibrium thermodynamic compositions related to the thermal reduction and water splitting steps are determined. The effect of oxygen partial pressure in the inert flushing gas on the thermal reduction temperature (TH is examined. An analysis based on the second law of thermodynamics is performed to determine the cycle efficiency (ηcycle and solar-to-fuel energy conversion efficiency (ηsolar−to−fuel attainable with and without heat recuperation. The results indicate that ηcycle and ηsolar−to−fuel both increase with decreasing TH, due to the reduction in oxygen partial pressure in the inert flushing gas. Furthermore, the recuperation of heat for the operation of the cycle significantly improves the solar reactor efficiency. For instance, in the case where TH = 2280 K, ηcycle = 24.4% and ηsolar−to−fuel = 29.5% (without heat recuperation, while ηcycle = 31.3% and ηsolar−to−fuel = 37.8% (with 40% heat recuperation.

The effect of samarium doping on structure and enhanced thermionic emission properties of lanthanum hexaboride fabricated by spark plasma sintering

Energy Technology Data Exchange (ETDEWEB)

Zhou, Shenlin; Hu, Qianglin [College of Mathematics and Physics, Jinggangshan University, Jian (China); Zhang, Jiuxing; Liu, Danmin [Key Laboratory of Advanced Functional Materials, Ministry of Education, College of Materials Science and Engineering, Beijing University of Technology, Beijing (China); Huang, Qingzhen [NIST Center for Neutron Research, National Institute of Standards and Technology, MD (United States)

2014-03-15

Single-phase polycrystalline solid solutions (La{sub 1-x}Sm{sub x})B{sub 6} (x = 0, 0.2, 0.4, 0.8, 1) are fabricated by spark plasma sintering (SPS). This study demonstrates a systematic investigation of structure-property relationships in Sm-doped LaB{sub 6} ternary rare-earth hexaborides. The microstructure, crystallographic orientation, electrical resistivity, and thermionic emission performance of these compounds are investigated. Analysis of the results indicates that samarium (Sm) doping has a noticeable effect on the structure and performance of lanthanum hexaboride (LaB{sub 6}). The analytical investigation of the electron backscatter diffraction confirms that (La{sub 0.6}Sm{sub 0.4})B{sub 6} exhibits a clear (001) texture that results in a low work function. Work functions are determined by pulsed thermionic diode measurements at 1500-1873 K. The (La{sub 0.6}Sm{sub 0.4})B{sub 6} possesses improved thermionic emission properties compared to LaB{sub 6}. The current density of (La{sub 0.6}Sm{sub 0.4})B{sub 6} is 42.4 A cm{sup -2} at 1873 K, which is 17.5% larger than that of LaB{sub 6}. The values of Φ{sub R} for (La{sub 0.6}Sm{sub 0.4})B{sub 6} and LaB{sub 6} are 1.98 ± 0.03 and 1.67 ± 0.03 eV, respectively. Furthermore, the Sm substitution of lanthanum (La) effectively increases the electrical resistivity. These results reveal that Sm doping lead to significantly enhanced thermionic emission properties of LaB{sub 6}. The compound (La{sub 0.6}Sm{sub 0.4})B{sub 6} appears most promising as a future emitter material. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The properties of samarium-doped zinc oxide/phthalocyanine structure for optoelectronics prepared by pulsed laser deposition and organic molecular evaporation

Czech Academy of Sciences Publication Activity Database

Novotný, Michal; Marešová, Eva; Fitl, Přemysl; Vlček, Jan; Bergmann, M.; Vondráček, Martin; Yatskiv, Roman; Bulíř, Jiří; Hubík, Pavel; Hruška, Petr; Drahokoupil, Jan; Abdellaoui, N.; Vrňata, M.; Lančok, Ján

2016-01-01

Roč. 122, č. 3 (2016), 1-8, č. článku 225. ISSN 0947-8396 R&D Projects: GA MŠk(CZ) LG15050; GA ČR(CZ) GAP108/11/0958; GA MŠk(CZ) LM2011029; GA ČR(CZ) GA14-10279S; GA MŠk(CZ) 7AMB14FR010 Institutional support: RVO:68378271 ; RVO:67985882 Keywords : samarium-doped zinc oxide zinc/phthalocyanine deposition * evaporation * pulsed laser deposition * thin films Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.455, year: 2016

Cross sections for d-{sup 3}H neutron interactions with samarium isotopes

Energy Technology Data Exchange (ETDEWEB)

Luo, Junhua; He, Long [Hexi Univ., Zhangye (China). School of Physics and Electromechanical Engineering; Wu, Chunlei; Jiang, Li [Chinese Academy of Engineering Physics, Mianyang (China). Inst. of Nuclear Physics and Chemistry

2016-11-01

The cross sections for (n,x) reactions on samarium isotopes were measured at (d-T) neutron energies of 13.5 and 14.8 MeV with the activation technique. Samples were activated along with Nb and Al monitor foils to determine the incident neutron flux. Theoretical calculations of excitation functions were performed using the nuclear model codes TALYS-1.6 and EMPIRE-3.2 Malta with default parameters, at neutron energies varying from the reaction threshold to 20 MeV. The results were discussed and compared with experimental data found in the literature. At neutron energies 13.5 and 14.8 MeV, the cross sections of the {sup 149}Sm(n,p){sup 149}Pm reaction are reported for the first time. The cross sections of the {sup 150}Sm(n,p){sup 150}Pm, {sup 144}Sm(n,p){sup 144}Pm, {sup 152}Sm(n,α){sup 149}Nd and {sup 144}Sm(n,α){sup 141}Nd reactions at different neutron energies reported in the present work can be added as new data in the nuclear databases.

Charge and transition densities of samarium isotopes in the interacting Boson model

International Nuclear Information System (INIS)

Moinester, M.A.; Alster, J.; Dieperink, A.E.L.

1982-01-01

The interacting boson approximation (IBA) model has been used to interpret the ground-state charge distributions and lowest 2 + transition charge densities of the even samarium isotopes for A = 144-154. Phenomenological boson transition densities associated with the nucleons comprising the s-and d-bosons of the IBA were determined via a least squares fit analysis of charge and transition densities in the Sm isotopes. The application of these boson trasition densities to higher excited 0 + and 2 + states of Sm, and to 0 + and 2 + transitions in neighboring nuclei, such as Nd and Gd, is described. IBA predictions for the transition densities of the three lowest 2 + levels of 154 Gd are given and compared to theoretical transition densities based on Hartree-Fock calculations. The deduced quadrupole boson transition densities are in fair agreement with densities derived previously from 150 Nd data. It is also shown how certain moments of the best fit boson transition densities can simply and sucessfully describe rms radii, isomer shifts, B(E2) strengths, and transition radii for the Sm isotopes. (orig.)

Thermodynamics of coproportionation reactions of homogeneous samarium (3) and yttrium (3) nitrates solvates with neutral organic phosphorus compounds

International Nuclear Information System (INIS)

Pyartman, A.K.

1995-01-01

Reaction heats of homogeneous samarium (3) and yttrium (3) nitrate solvates coproportionation with neutral organophosphoric compounds (tri-n.-butylphosphate, diisooctylmethylphosphonate, diisoamylmethylphosphonate) at T=298.15 K in hexane have been measured by thermochemical method. It has been ascertained that enthalpies of coproportionation reactions practically do not depend on the nature, concentration of rare earth metal (3) nitrate solvates in hexane, nature of neutral organophosphoric compound and constitute 1.1±-.2 kJ/mol. The Gibbs free energy of coproportionation reactions is -5.43 kJ/mol, while entropy of the reactions in 14.5±0.7 J/mol·K. 8 refs., 1 tab

Study of samarium modified lead zirconate titanate and nickel zinc ferrite composite system

Energy Technology Data Exchange (ETDEWEB)

Rani, Rekha [Department of Physics, SD PG College, Panipat 132103 (India); School of Physics and Materials Science, Thapar University, Patiala 147004 (India); Juneja, J.K., E-mail: jk_juneja@yahoo.com [Department of Physics, Hindu College, Sonepat 131001 (India); Singh, Sangeeta [Department of Physics, GVM Girls College, Sonepat 131001 (India); Raina, K.K. [School of Physics and Materials Science, Thapar University, Patiala 147004 (India); Prakash, Chandra [Solid State Physics Laboratory, Timarpur, Delhi 110054 (India)

2015-03-15

In the present work, composites of samarium substituted lead zirconate titanate and nickel zinc ferrite with compositional formula 0.95Pb{sub 1−3x/2} Sm{sub x}Zr{sub 0.65}Ti{sub 0.35}O{sub 3}–0.05Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} (x=0, 0.01, 0.02 and 0.03) were prepared by the conventional solid state route. X-ray diffraction analysis was carried out to confirm the coexistence of individual phases. Microstructural study was done by using scanning electron microscope. Dielectric constant and loss were studied as a function of temperature and frequency. To study ferroelectric and magnetic properties of the composite samples, corresponding P–E and M–H hysteresis loops were recorded. Change in magnetic properties of electrically poled composite sample (x=0.02) was studied to confirm the magnetoelectric (ME) coupling. ME coefficient (dE/dH) of the samples (x=0 and 0.02) was measured as a function of DC magnetic field. - Highlights: • We are reporting the effect of Sm substitution on PZT–NiZn ferrite composites. • Observation of both P–E and M–H loops confirms ferroelectric and magnetic ordering. • With Sm substitution, significant improvement in properties was observed. • Increase in magnetization for electrically poled sample is evidence of ME coupling. • Electric polarization is generated by applying magnetic field.

Efficacy and toxicity of Samarium-153-EDTMP locally produced in the treatment of painful skeletal metastases

International Nuclear Information System (INIS)

Olea, E.; Quintana, J.C.; Nagel, J.; Arenas, L.; Tomicic, M.; Gil, M.C.; Araya, G.

2001-01-01

Samarium-153 emits medium-energy beta particles an a gamma photon with a physical half-life of 46,3 hours. When chelated to ethylenediaminetetramethylenephosphonic acid (EDTMP), it is remarkably stable in vitro and in vivo. In this study we administered randomly 0,5 and 1,0 mCi/Kg body weight (two groups), to 30 patients with painful metastatic bone cancer. Slight and spontaneously reversible myelotoxicity was observed. A bigger leukocyte and platelet suppression was obtained with 1,0 mCi/kg than 0,5 mCi/Kg dose. Pain palliation was obtained in 66% of the treated patients. Our preliminary results indicate that 153 Sm-EDTMP is a promising radiotherapeutic agent for palliative treatment of metastatic bone cancer pain where a reactor is available and at a very affordable cost. (author)

Determination of the nuclear electric charge distribution of samarium isotopes 144, 148, 150, 152, 154 by the muonic atom method

International Nuclear Information System (INIS)

Barreau, Pierre.

1977-01-01

The theory of the nucleus-negative muon system in the case of electrical interactions is discussed. The interactions of muons with the samarium isotopes 152, 154, 144, 148, 150 are investigated. After a description of the experimental device, from muon beam production to data acquisition (detection of the gamma spectra), the results are analyzed and the nuclear charge distribution parameters determined: for each isotope the absolute value of c (half-density radius) and t (skin thickness); for 152 Sm and 154 Sm the parameter β 2 (quadrupolar defomation). Nuclear polarization was accounted for throughout the analysis [fr

Pharmacokinetics of labelled compounds with technetium-99m and samarium-153

International Nuclear Information System (INIS)

Borda O, L.B.; Torres L, M.N.

1997-01-01

The purpose of this investigation was to establish the different pharmacokinetics parameters of the main radiopharmaceuticals labeled with technetium-99m and samarium-153. These parameters could be subsequently used as reference to compare other products with the same use. Mathematical models and a computerized pharmacokinetic program were used to this purpose. A biodistribution study in quadruplicate and/or quintuplicate was conducted for each radiopharmaceutical, data was was obtained in injection dose percentages. The biodistribution study involved the injection of a predetermined dose of the radiopharmaceutical into animals (rats or mice), which were subsequently put away at different time intervals, removing the relevant organs. Activity in each organ was read by means of a well-type NaI scintillation counter, data obtained in activity counts was transformed into injection dose percentages. Based on these percentages, the mathematical model was constructed and the pharmacokinetic parameters were obtained using the computerized program Expo 2 v. 1, which is written in C language and works in windows. Analyzing the results obtained, we can conclude that the use of the Expo 2 v. 1 program for a bi compartmental analysis allowed us to obtain reliable pharmacokinetic parameters which describe what happens in the organism when the radiopharmaceutical passes from the central compartment to the peripheral one and vice versa

Studies on the structural, optical and dielectric properties of samarium coordinated with salicylic acid single crystal

Science.gov (United States)

Singh, Harjinder; Slathia, Goldy; Gupta, Rashmi; Bamzai, K. K.

2018-04-01

Samarium coordinated with salicylic acid was successfully grown as a single crystal by low temperature solution technique using mixed solvent of methanol and water in equal ratio. Structural characterization was carried out by single crystal X-ray diffraction analysis and it crystallizes in centrosymmetric space group P121/c1. FTIR and UV-Vis-NIR spectroscopy confirmed the compound formation and help to determine the mode of binding of the ligand to the rare earth-metal ion. Dielectric constant and dielectric loss have been measured over the frequency range 100 Hz - 30MHz. The decrease in dielectric constant with increases in frequency is due to the transition from interfacial polarization to dipolar polarization. The small value of dielectric constant at higher frequency ensures that the crystal is good candidate for NLO devices. Dielectric loss represents the resistive nature of the material.

Synthesis and characterization of samarium-doped ZnS nanoparticles: A novel visible light responsive photocatalyst

Energy Technology Data Exchange (ETDEWEB)

Hanifehpour, Younes, E-mail: y_hanifehpour@yu.ac.kr [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Soltani, Behzad; Amani-Ghadim, Ali Reza; Hedayati, Behnam [Department of Chemistry, Faculty of Basic Sciences, Azarbaijan Shahid Madani University, Tabriz (Iran, Islamic Republic of); Khomami, Bamin [Department of Chemical and Biomolecular Engineering, University of Tennessee, Knoxville, TN 37996 (United States); Joo, Sang Woo, E-mail: swjoo1@gmail.com [School of Mechanical Engineering, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of)

2016-04-15

Highlights: • Sm-doped ZnS Nanomaterials were synthesized by hydrothermal method. • The as-prepared compounds were characterized by XRD, TEM, XPS, SEM and UV techniques. • The photocatalytic effect of compounds was determined by Reactive Red 43 degradation. • The degradation of RRed 43 followed the Langmuir–Hinshelwood kinetic model. - Abstract: We prepared pure and samarium-doped ZnS (Sm{sub x}Zn{sub 1−x}S{sub 1+0.5x}) nanoparticles via hydrothermal process at 160 °C for 24 h. XRD analysis shows that the particles were well crystallized and corresponds to a cubic sphalerite phase. SEM and TEM images indicate that the sizes of the particles were in the range of 20–60 nm. The photocatalytic activity of Sm-doped ZnS nanoparticles was evaluated by monitoring the decolorization of Reactive Red 43 in aqueous solution under visible light irradiation. The color removal efficiency of Sm{sub 0.04}Zn{sub 0.96}S and pure ZnS was 95.1% and 28.7% after 120 min of treatment, respectively. Among the different amounts of dopant agent used, 4% Sm-doped ZnS nanoparticles indicated the highest decolorization. We found that the presence of inorganic ions such as Cl{sup −}, CO{sub 3}{sup 2−} and other radical scavengers such as buthanol and isopropyl alcohol reduced the decolorization efficiency.

Study of unstable valences of cadmium and samarium by pulse radiolysis. Influence of complexation by some synthetical ionophores

International Nuclear Information System (INIS)

Lerat-Parizot, O.

1992-01-01

Instable valences of cations in solution are evidenced by pulse radiolysis, in spite of a lifetime often lower than a milli-second they participate to electron transfer reactions, owing to their redox potential. In this work are studied Cd + and Sm 2+ obtained respectively by reduction of Cd 2+ and Sm 3+ by a solvated electron. The reactivity of Cd + in a cryptand and in a coronand is studied; it is a powerful reducing agent (redox potential -2V) going back to the stable valence by electron transfer to an acceptor. Transfer kinetics is studied by reduction of organic molecules, effect of solvents and ligands is also examined. For samarium the reduction kinetics by hydrated electrons is increased when the ion is in a cryptand in agreement with electrochemical observations, showing that the valence 2+ is stabilized in respect to the valence 3+ for lanthanides. The difference of behaviour between Cd + and Sm 2+ is probably due to the fact that for Cd the transferred electron comes from the external layer and for Sm it is a f electron protected by the 5s and 5p orbitals

Detonation nanodiamond introduced into samarium doped ceria electrolyte improving performance of solid oxide fuel cell

Science.gov (United States)

Pei, Kai; Li, Hongdong; Zou, Guangtian; Yu, Richeng; Zhao, Haofei; Shen, Xi; Wang, Liying; Song, Yanpeng; Qiu, Dongchao

2017-02-01

A novel electrolyte materials of introducing detonation nanodiamond (DNDs) into samarium doped ceria (SDC) is reported here. 1%wt. DNDs doping SDC (named SDC/ND) can enlarge the electrotyle grain size and change the valence of partial ceria. DNDs provide the widen channel to accelerate the mobility of oxygen ions in electrolyte. Larger grain size means that oxygen ions move easier in electrolyte, it can also reduce the alternating current (AC) impedance spectra of internal grains. The lower valence of partial Ce provides more oxygen vacancies to enhance mobility rate of oxygen ions. Hence all of them enhance the transportation of oxygen ions in SDC/ND electrolyte and the OCV. Ultimately the power density of SOFC can reach 762 mw cm-2 at 800 °C (twice higher than pure SDC, which is 319 mw cm-2 at 800 °C), and it remains high power density in the intermediate temperature (600-800 °C). It is relatively high for the electrolyte supported (300 μm) cells.

Use of dispersive liquid-liquid microextraction for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium

International Nuclear Information System (INIS)

Mallah, M.H.; Atomic Energy Organization of Iran, Tehran; Shemirani, F.; Ghannadi Maragheh, M.

2008-01-01

A new preconcentration method of dispersive liquid-liquid microextraction (DLLME) was developed for simultaneous preconcentration of samarium, europium, gadolinium and dysprosium. DLLME technique was successfully used as a sample preparation method. In this preconcentration method, an appropriate mixture of extraction solvent, disperser solvent was injected rapidly into an aqueous solution containing Sm, Eu, Gd and Dy after complex formation using chelating reagent of the 1-(2-pyridylazo)-2-naphthol (PAN). After phase separation, 0.5 mL of the settled phase containing enriched analytes was determined by inductively coupled plasma optical emission spectrometry (ICP-OES). The main factors affected the preconcentration of Sm, Eu, Gd and Dy were extraction and dispersive solvent type and their volume, extraction time, volume of chelating agent (PAN), centrifuge speed and drying temperature of the samples. Under the best operating condition simultaneous preconcentration factors of 80, 100, 103 and 78 were obtained for Sm, Eu, Gd and Dy, respectively. (author)

Characterization of luminescent samarium doped HfO2 coatings synthesized by spray pyrolysis technique

International Nuclear Information System (INIS)

Chacon-Roa, C; Guzman-Mendoza, J; Aguilar-Frutis, M; Garcia-Hipolito, M; Alvarez-Fragoso, O; Falcony, C

2008-01-01

Trivalent samarium (Sm 3+ ) doped hafnium oxide (HfO 2 ) films were deposited using the spray pyrolysis deposition technique. The films were deposited on Corning glass substrates at temperatures ranging from 300 to 550 deg. C using chlorides as raw materials. Films, mostly amorphous, were obtained when deposition temperatures were below 350 deg. C. However, for temperatures higher than 400 deg. C, the films became polycrystalline, presenting the HfO 2 monoclinic phase. Scanning electron microscopy of the films revealed a rough surface morphology with spherical particles. Also, electron energy dispersive analysis was performed on these films. The photoluminescence and cathodoluminescence characteristics of the HfO 2 : SmCl 3 films, measured at room temperature, exhibited four main bands centred at 570, 610, 652 and 716 nm, which are due to the well-known intra-4f transitions of the Sm 3+ ion. It was found that the overall emission intensity rose as the deposition temperature was increased. Furthermore, a concentration quenching of the luminescence intensity was also observed

The theoretical basis and clinical methodology for stereotactic interstitial brain tumor irradiation using iododeoxyuridine as a radiation sensitizer and samarium-145 as a brachytherapy source

International Nuclear Information System (INIS)

Goodman, J.H.; Gahbauer, R.A.; Kanellitsas, C.; Clendenon, N.R.; Laster, B.H.; Fairchild, R.G.

1989-01-01

High grade astrocytomas have proven resistant to all conventional therapy. A technique to produce radiation enhancement during interstitial brain tumor irradiation by using a radiation sensitizer (IdUrd) and by stimulation of Auger electron cascades through absorption of low energy photons in iodine (Photon activation) is described. Clinical studies using IdUrd, 192 Ir as a brachytherapy source, and external radiation have produced promising results. Substituting samarium-145 for 192 Ir in this protocol is expected to produce enhanced results. 15 refs

Effects of samarium (Sm) additions on the microstructure and mechanical properties of as-cast and hot-extruded Mg-5 wt%Al-3 wt%Ca-based alloys

International Nuclear Information System (INIS)

Son, Hyeon-Taek; Lee, Jae-Seol; Kim, Dae-Guen; Yoshimi, Kyosuke; Maruyama, Kouichi

2009-01-01

Samarium (Sm) additions to as-cast Mg-5Al-3Ca-based alloys result in changes, such as equiaxed grains and a refined grain size. The microstructure of as-cast Mg-5Al-3Ca-xSm alloys consists of an α-Mg matrix, a (Mg, Al) 2 Ca eutectic phase, and an Al 2 Sm intermetallic compound. In as-cast alloys, the (Mg, Al) 2 Ca eutectic phase was located at grain boundaries with a chain structure, and the Al 2 Sm intermetallic compounds were homogeneously distributed at the α-Mg matrix and grain boundaries. The eutectic phase of the extruded alloys was elongated in the extrusion direction and crushed into fine particles because of severe deformation during hot extrusion, and the grain size was refined with an increased amount of Sm addition. The maximum values of the yield strength and tensile strength were 313 MPa and 330 MPa at 2 wt%Sm alloy content, respectively

Biodistribution of samarium-153-EDTMP in rats treated with docetaxel Biodistribuição de EDTMP-153-samário em ratos tratados com docetaxel

Directory of Open Access Journals (Sweden)

Arthur Villarim Neto

2009-02-01

Full Text Available PURPOSE: Many patients with metastatic bone disease have to use radiopharmaceuticals associated with chemotherapy to relieve bone pain. The aim of this study was to assess the influence of docetaxel on the biodistribution of samarium-153-EDTMP in bones and other organs of rats. METHODS: Wistar male rats were randomly allocated into 2 groups of 6 rats each. The DS (docetaxel/samarium group received docetaxel (15 mg/kg intraperitoneally in two cycles 11 days apart. The S (samarium/control group rats were not treated with docetaxel. Nine days after chemotherapy, all the rats were injected with 0.1ml of samarium-153-EDTMP via orbital plexus (25µCi. After 2 hours, the animals were killed and samples of the brain, thyroid, lung, heart, stomach, colon, liver, kidney and both femurs were removed. The percentage radioactivity of each sample (% ATI/g was determined in an automatic gamma-counter (Wizard-1470, Perkin-Elmer, Finland. RESULTS: On the 9th day after the administration of the 2nd chemotherapy cycle, the rats had a significant weight loss (314.50±22.09g compared (pOBJETIVO: Muitos pacientes com metástases ósseas são tratados com radiofármacos associados com quimioterapia para alívio da dor óssea. O objetivo do trabalho foi estudar a influência do docetaxel na biodistribuição do EDTMP-153-samário nos ossos e outros órgãos de ratos. MÉTODOS: Ratos Wistar foram aleatoriamente alocados em 2 grupos de 6 animais cada. O grupo DS (docetaxel/samário recebeu docetaxel (15 mg/kg intraperitoneal em dois ciclos com 11 dias de intervalo. Os ratos do grupo S (samário/controle não foram tratados com docetaxel. Nove dias após a quimioterapia, todos os animais receberam 0,1ml de EDTMP-153-samário via plexo orbital (25µCi. Após 2 horas, os animais foram mortos e feitas biópsias de cérebro, tireóide, pulmão, coração, estômago, cólon, fígado, rim e fêmures. O percentual de radioatividade por grama (%ATI/g de tecido de cada bi

Samarium-153 Oksabifor in the treatment of metastatic bone disease

International Nuclear Information System (INIS)

Solodyannikova, O.; Voit, N.; Sukach, G.; Sagan, D.

2015-01-01

patients - reducing the number of foci and the level of radiopharmaceutical uptake in them. Conclusions: radionuclide therapy in patients with BM can effectively suppress pain and significantly reduce the number of analgesics. Post-treatment patients, life quality statistically significantly improved. Samarium-153 has the ability to reduce BM number and intensity of radiopharmaceutical accumulation in spots in the control study. (authors)

Development and evaluation of copper-67 and samarium-153 labeled conjugates for tumor radioimmunotherapy

International Nuclear Information System (INIS)

Srivastava, S.C.; Mausner, L.F.; Mease, R.C.; Meinken, G.E.; Joshi, V.; Kolsky, K.; Sweet, M.; Steplewski, Z.

1995-01-01

The potential of utilizing receptor-specific agents such as monoclonal antibodies (MAb), and MAb-derived smaller molecules, as carriers of radionuclides for the selective destruction of tumors has stimulated much research activity. The success of such applications depends on many factors, especially the tumor binding properties of the antibody reagent, the efficiency of labeling and in-vivo stability of the radioconjugate and, on the careful choice of the radionuclide best suited to treat the tumor under consideration. The radiolabeled antibody technique for radioimmunotherapy (RIT), however, has experienced many limitations, and its success has not matched the expectations that were raised more than a decade ago. The problems that have been identified include: (i) degradation of antibody immunoreactivity resulting from chemical manipulations required for labeling; (ii) lack of suitable radioisotopes and methods for stable attachment of the radiolabel; (iii) in-vivo instability of the radioimmunoconjugates; (iv) excessive accumulation of activity in non-target locations; and (v) lack of radioimmunoconjugate accessibility to cells internal to a tumor mass. A careful choice of the radionuclide(s) best suited to treat the tumor under consideration is one of the most important requirements for successful radioimmunotherapy. This study evaluates copper 67 and samarium 153 for tumor radioimmunotherapy

Retention capacity of samarium (III) in zircon for it possible use in retaining walls for confinement of nuclear residues; Capacidad de retencion de samario (III) en circon para su posible uso en barreras de contencion para confinamiento de residuos nucleares

Energy Technology Data Exchange (ETDEWEB)

Garcia G, N

2006-07-01

Mexico, as country that produces part of its electric power by nuclear means, should put special emphasis in the development of technologies guided to the sure and long term confinement of the high level nuclear residuals. This work studies the capacity that has the natural zircon to retain to the samarium (III) in solution, by what due, firstly, to characterize the zircon for technical instrumental to determine the purity and characteristic of the mineral in study. The instrumental techniques that were used to carry out the physicochemical characterization were the neutron activation analysis (NAA), the infrared spectroscopy (IS), the thermal gravimetric analysis (TGA), scanning electron microscopy (SEM), transmission electron microscopy (TEM), semiquantitative analysis, dispersive energy spectroscopy (EDS), X-ray diffraction (XRD) and luminescence technique. The characterization of the surface properties carries out by means of the determination of the surface area using the BET multipoint technique, acidity constants, hydration time, the determination of the point of null charge (pH{sub PCN}) and density of surface sites (D{sub s}). The luminescence techniques were useful to determine the optimal point hydration of the zircon and for the quantification of the samarium, for that here intends the development of both analysis techniques. With the adjustment of the titration curves in the FITEQL 4 package the constants of surface acidity in the solid/liquid interface were determined. To the finish of this study it was corroborated that the zircon is a mineral that presents appropriate characteristics to be proposed as a contention barrier for the deep geologic confinement. With regard to the study of adsorption that one carries out the samarium retention it is superior to 90% under the described conditions. This investigation could also be applicable in the confinement of dangerous industrial residuals. (Author)

Ferrites Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} doped with samarium: structural analysis, morphological and electromagnetic; Ferritas Ni{sub 0,5}Zn{sub 0,5}Fe{sub 2}O{sub 4} dopada com samario: analise estrutural, morfologica e eletromagnetica

Energy Technology Data Exchange (ETDEWEB)

Costa, A.C.F.M.; Diniz, A.P., E-mail: anacristina@dema.ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil). Unidade Academinca de Engenharia de Materiais; Viana, K.M.S. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, PE (Brazil). Escola de Ciencias e Tecnologia; Cornejo, D.R. [Universidade de Sao Paulo (USP), SP (Brazil). Instituto de Fisica; Kiminami, R.H.G.A. [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

2010-07-01

This paper proposes to investigate the sintering at 1200 deg C/2h of Ni{sub 0.5}Zn{sub 0.5}Fe{sub 2-x}Sm{sub x}O{sub 4} ferrite doped with 0.05; 0.075 e 0.1 mol of Sm synthesized by combustion reaction to evaluate the performance materials as absorbers of electromagnetic radiation. The influence of the concentration of samarium on the structure, morphology and electromagnetic properties of ferrites was studied. The resulting samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), magnetic measurements and reflectivity measurements in the frequency range between 8-12 GHz. The results showed that increasing the concentration of samarium caused a decrease in particle size of the samples, encouraging, therefore, to obtain materials with better values of magnetization and reflectivity, allowing for use as absorbers in narrow-band frequency between 9-10 GHz. (author)

An estimation of influence of humic acid and organic matter originated from bentonite on samarium solubility

International Nuclear Information System (INIS)

Kanaji, Mariko; Sato, Haruo; Sasahira, Akira

1999-10-01

Organic acids in groundwater are considered to form complexes and increase the solubility of radionuclides released from vitrified waste in a high-level radioactive waste (HLW) repository. To investigate whether the solubility of samarium (Sm) is influenced by organic substances, we measured Sm solubility in the presence of different organic substances and compared those values with results from thermodynamic predictions. Humic acid (Aldrich) is commercially available and soluble organic matter originated from bentonite were used as organic substances in this study. Consequently, the solubility of Sm showed a tendency to apparently increase with increasing the concentration of humic acid, but in the presence of carbonate, thermodynamic predictions suggested that the dominant species are carbonate complexes and that the effect of organic substances are less than that of carbonate. Based on total organic carbon (TOC), the increase of Sm solubility measured with humic acid (Aldrich) was more significant than that in the case with soluble organic matter originated from bentonite. Since bentonite is presumed to include also simple organic matters of which stability constant for forming complexes is low, the effect of soluble organic matter originated from bentonite on the solubility of Sm is considered to be less effective than that of humic acid (Aldrich). Experimental values were compared with model prediction, proposed by Kim, based on data measured in a low pH region. Tentatively we calculated the increase in Sm solubility assuming complexation with humic acid. Trial calculations were carried out on the premise that the complexation reaction of metal ion with humic acid is based on neutralization process by 1-1 complexation. In this process, it was assumed that one metal ion coordinates with one unit of complexation sites which number of proton exchange sites is equal to ionic charge. Consequently, Kim's model indicated that carbonate complexes should be dominant

Observation of near infrared and enhanced visible emissions from electroluminescent devices with organo samarium(III) complex

Energy Technology Data Exchange (ETDEWEB)

Chu, B [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, W L [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Hong, Z R [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Zang, F X [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wei, H Z [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Wang, D Y [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Li, M T [Key Laboratory of the Excited States Process, Changchun Institute of Optics, Fine Mechanics and Physics, Chinese Academy of Sciences, 16-Dong NanHu Road, Economic Development Area, Changchun, 130033 (China); Lee, C S [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China); Lee, S T [Department of Physics and Materials Science, City University of Hong Kong, Hong Kong (China)

2006-11-07

Samarium (dibenzoylmethanato){sub 3} bathophenanthroline (Sm(DBM){sub 3} bath) was employed as an emitting and electron transport layer in organic light emitting diodes (OLEDs), and narrow electroluminescent (EL) emissions of a Sm{sup 3+} ion were observed in the visible and near infrared (NIR) region, differing from those of the same devices with Eu{sup 3+}- or Tb{sup 3+}-complex EL devices with the same structure. The EL emissions of the Sm{sup 3+}-devices originate from transitions from {sup 4}G{sub 5/2} to the lower respective levels of Sm{sup 3+} ions. A maximum luminance of 490 cd m{sup -2} at 15 V and an EL efficiency of 0.6% at 0.17 mA cm{sup -2} were obtained in the visible region, and the improved efficiency should be attributed to introducing a transitional layer between the N,N'-diphenyl-N,N'-bis(3-methylphenyl)-1,1'-diphenyl-4,4'-diamine (TPD) film and the Sm(DBM){sub 3} bath film and the avoidance of interfacial exciplex emission in devices. Sharp emissions of Sm{sup 3+} ions in the NIR region were also observed under a lower threshold value less than 4.5 V.

Study for the determination of samarium, europium,terbium, dysprosium and yttrium in gadolinium oxide matrix by means of atomic absorption spectrophotometry using a graphite furnace

International Nuclear Information System (INIS)

Caires, A.C.F.

1985-01-01

A study for determination of samarium, europium, terbium, dysprosium and yttrium in a gadolinium oxide matrix by atomic absorption spectrophotometry using a graphite furnace is presented. The best charrring and atomization conditions were estabilished for each element, the most convenient ressonance lines being selected as well. The study was carried out for the mentioned lanthanides both when pure and when in binary mixtures with gadolinium, besides those where all for them were together with gadolinium. The determination limits for pure lanthanides were found to be between 1.3 and 9.6 ng assuming a 20% relative standard deviation as acceptable. The detection limits were in the range 0.51 and 7.5 ng, assuming as positive any answer higher than twofold the standard deviation. (author) [pt

Anchoring samarium oxide nanoparticles on reduced graphene oxide for high-performance supercapacitor

Energy Technology Data Exchange (ETDEWEB)

Dezfuli, Amin Shiralizadeh [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Ganjali, Mohammad Reza, E-mail: ganjali@khayam.ut.ac.ir [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of); Biosensor Research Center, Endocrinology & Metabolism Molecular-Cellular Sciences Institute, Tehran University of Medical Sciences, Tehran (Iran, Islamic Republic of); Naderi, Hamid Reza [Center of Excellence in Electrochemistry, Faculty of Chemistry, University of Tehran, Tehran (Iran, Islamic Republic of)

2017-04-30

Highlights: • Samarium oxide nanoparticles have been anchored on the surface of reduced graphene oxide for the first time. • Sm{sub 2}O{sub 3}/RGO nanocomposite show high capacitance, good rate and cycling performance. • Sm{sub 2}O{sub 3}/RGO nanocomposite can serve as efficient electrode material for energy storage. • The best composite electrode exhibits specific capacitance of 321 F g{sup −1} in 2 mV s{sup −1}. - Abstract: We have synthesized Sm{sub 2}O{sub 3} nanoparticles (SmNs) and anchored them onto the surface of reduced graphene oxide (RGO) through a self-assembly thereof by utilizing a facile sonochemical procedure. The nanomaterials were characterized by means of powder X-ray diffraction (XRD), Field-emission scanning electron microscopy (FE-SEM), fourier transform infrared spectroscopy (FT-IR) spectra, and X-ray photoelectron spectroscopy (XPS). As the next step, the supercapacitive behavior of the resulting nanocomposites were investigated when used as electrode material, through with cyclic voltammetric (CV), galvanostatic charge-discharge and electrochemical impedance spectroscopy (EIS) techniques. The SmNs decorated RGO (SmN-RGO) nanocomposites were found to possess a specific capacitance (SC) of 321 F g{sup −1} when used in a 0.5 M Na{sub 2}SO{sub 4} solution as an electrolyte, in a scan rate of 2 mV s{sup −1}. The SC of the SmN-RGO based electrodes were also found to be 268 F g{sup −1} at a current density of 2 A g{sup −1} through galvanostatic charge-discharge tests. The outstanding properties of the SmN-RGOs were attributed to synergy of the high charge mobility of SmNs and the flexibility of the sheets of RGOs. Additionally, the nano-composite revealed a unique cycling durability (maintaining 99% of its SC even after 4000 cycles).

Samarium-modified vanadium phosphate catalyst for the selective oxidation of n-butane to maleic anhydride

International Nuclear Information System (INIS)

Wu, Hua-Yi; Wang, Hai-Bo; Liu, Xin-Hua; Li, Jian-Hui; Yang, Mei-Hua; Huang, Chuan-Jing; Weng, Wei-Zheng; Wan, Hui-Lin

2015-01-01

Graphical abstract: The addition of a small amount of Sm into VPO catalyst brought about great changes in its physicochemical properties such as surface area, surface morphology, phase composition and redox property, thus leading to a higher catalytic performance in the selective oxidation of n-butane to maleic anhydride, as compared to the undoped VPO catalyst. - Highlights: • The addition of Sm leads to great changes in the structure of VPO catalyst. • Sm improves performance of VPO for oxidation of n-butane to maleic anhydride. • Catalytic performance is closely related to structure of VPO catalyst. - Abstract: A series of samarium-modified vanadium phosphate catalysts were prepared and studied in selective oxidation of n-butane to maleic anhydride. The catalytic evaluation showed that Sm modification significantly increased the overall n-butane conversion and intrinsic activity. N 2 -adsorption, XRD, SEM, Raman, XPS, EPR and H 2 -TPR techniques were used to investigate the intrinsic difference among these catalysts. The results revealed that the addition of Sm to VPO catalyst can increase the surface area of the catalyst, lead to a significant change in catalyst morphology from plate-like structure into rosette-shape clusters, and largely promote the formation of (VO) 2 P 2 O 7 . All of these were related to the different catalytic performance of Sm-doped and undoped VPO catalysts. The roles of the different VOPO 4 phases and the influence of Sm were also described and discussed

Dgroup: DG01196 [KEGG MEDICUS

Lifescience Database Archive (English)

Full Text Available DG01196 Chemical ... DGroup Samarium (153Sm) lexidronam ... D08504 ... Samarium (153Sm) lexidron...am (INN) D05795 ... Samarium Sm 153 lexidronam pentasodium (USAN); Samarium (153Sm) lexidronam sodium (JA

An experiment using neutron activation analysis and a rare earth element to mark cotton plants and two insects that feed on them

Energy Technology Data Exchange (ETDEWEB)

Showler, Allan T. [USDA-ARS IFNRRU, Kika de la Garza Subtropical Agricultural Research Center, 2413 East Highway 83, Weslaco, TX 78596 (United States)]. E-mail: ashowler@weslaco.ars.usda.gov; James, William D. [Elemental Analysis Laboratory, 3144 Texas A and M University, College Station, TX 77843-3144 (United States); Armstrong, John S. [USDA-ARS BIRU, Kika de la Garza Subtropical Agricultural Research Center, 2413 East Highway 83, Weslaco, TX 78596 (United States); Westbrook, John K. [USDA-ARS APMRU, 2771 F and B Road, College Station, TX 77845-4966 (United States)

2006-08-15

Studies on insect dispersal and other behaviors can benefit from using markers that will not alter flight and fitness. Rare earth elements, such as samarium (Sm), have been used as ingested markers of some insects and detected using neutron activation analysis (NAA). In this study, samarium nitrate hexahydrate was mixed into artificial diet for boll weevils, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), at different dosages and in water used to irrigate cotton, Gossypium hirsutum L. Samarium was detected in adult boll weevils fed on the samarium-labeled diet, but not after 5 or 10 days of being switched to non-labeled diet, even if the insects were given labeled diet for as long as 7 consecutive days. Introduced in irrigation water, 1% samarium (m/m) was detectable in cotton squares and leaf tissue. However, boll weevil adults fed samarium-labeled squares did not retain detectable levels of samarium, nor did boll weevil adults reared to adulthood from samarium-labeled squares. Fourth instar beet armyworms, Spodoptera exigua (Huebner) (Noctuidae: Lepidoptera), fed on samarium-labeled cotton leaves obtained enough samarium for NAA detection, but adult moths reared from them did not have detectable amounts of samarium. Although samarium can be useful as a marker when insects are presented with a continuous pulse of the label, elements that are assimilated by the insect would be more useful if a continuous infusion of the marker cannot be provided.

Fabrication and properties of samarium doped calcium sulphate thin films using spray pyrolysis technique

Energy Technology Data Exchange (ETDEWEB)

Reghima, Meriem [Université Tunis El Manar, Faculté des Sciences de Tunis, Département de Physique, LR99ES13 Laboratoire de Physique de la Matière Condensée (LPMC), 2092 Tunis, Tunisie (Tunisia); Institut d' Electronique et des systèmes, Unité Mixte de Recherche 5214 UM2-CNRS (ST2i) – Université Montpellier, 860 rue de Saint Priest, Bâtiment 5, 34097 Montpellier (France); Faculté des Sciences de Bizerte, Université de Carthage, Zarzouna 7021 (Tunisia); Guasch, Cathy [Institut d' Electronique et des systèmes, Unité Mixte de Recherche 5214 UM2-CNRS (ST2i) – Université Montpellier, 860 rue de Saint Priest, Bâtiment 5, 34097 Montpellier (France); Azzaza, Sonia; Alleg, Safia [Laboratoire de Magnétisme et Spectroscopie des Solides (LM2S), Département de Physique, Faculté des Sciences, Université Badji Mokhtar Annaba, B.P. 12, 23000 Annaba (Algeria); Kamoun-Turki, Najoua [Université Tunis El Manar, Faculté des Sciences de Tunis, Département de Physique, LR99ES13 Laboratoire de Physique de la Matière Condensée (LPMC), 2092 Tunis, Tunisie (Tunisia)

2016-10-01

Using low cost spray pyrolysis technique, polycrystalline CaSO{sub 4} thin films were successfully grown on a glass substrate with a thickness of about 1 μm. Samarium doping has been performed on CaSO{sub 4} thin films to explore luminescence properties. The characterizations of these films were carried out using X-ray diffraction, Scanning Electron Microscopy and optical measurements. The structural analyses reveal the existence of hexagonal CaSO{sub 4} phase with a (200) preferred orientation belonging to CaS compound for substrate temperatures below 350 °C. It is shown that the crystallinity of the sprayed thin films can be improved by increasing substrate temperature up to 250 °C. Warren-Averbach analysis has been applied on X-ray diffractogram to determine structural parameters involving the phase with its amount, the grain size and the lattice parameters using Maud software. The surface topography shows a rough surface covered by densely packed agglomerated clusters having faceted and hexagonal shapes. Energy dispersive microscopy measurements confirm the presence of calcium and sulfur in equal proportions as well as high percentage of oxygen. Photoluminescence at room temperature revealed that luminescence peaks are attributed to the intrinsic emission of pure CaSO{sub 4} phase. - Highlights: • Warren Averbach analysis reveal the presence of hcp structure of CaSO{sub 4} phase. • A mixture of CaSO{sub 4} and CaHO{sub 4.5}S phases has been detected for lower T{sub s}. • For increasing T{sub s}, the CaHO{sub 4.5}S phase has been disappeared. • The origin of PL peaks has been identified.

Samarium oxide as a radiotracer to evaluate the in vivo biodistribution of PLGA nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Mandiwana, Vusani, E-mail: VMandiwana@csir.co.za; Kalombo, Lonji, E-mail: LKalombo@csir.co.za [Centre of Polymers and Composites, CSIR (South Africa); Venter, Kobus, E-mail: Kobus.Venter@mrc.ac.za [South African Medical Research Council (South Africa); Sathekge, Mike, E-mail: Mike.Sathekge@up.ac.za [University of Pretoria and Steve Biko Academic Hospital, Department of Nuclear Medicine (South Africa); Grobler, Anne, E-mail: Anne.Grobler@nwu.ac.za; Zeevaart, Jan Rijn, E-mail: zeevaart@necsa.co.za [North-West University, DST/NWU Preclinical Drug Development Platform (South Africa)

2015-09-15

Developing nanoparticulate delivery systems that will allow easy movement and localization of a drug to the target tissue and provide more controlled release of the drug in vivo is a challenge in nanomedicine. The aim of this study was to evaluate the biodistribution of poly(d,l-lactide-co-glycolide) (PLGA) nanoparticles containing samarium-153 oxide ([{sup 153}Sm]Sm{sub 2}O{sub 3}) in vivo to prove that orally administered nanoparticles alter the biodistribution of a drug. These were then activated in a nuclear reactor to produce radioactive {sup 153}Sm-loaded-PLGA nanoparticles. The nanoparticles were characterized for size, zeta potential, and morphology. The nanoparticles were orally and intravenously (IV) administered to rats in order to trace their uptake through imaging and biodistribution studies. The {sup 153}Sm-loaded-PLGA nanoparticles had an average size of 281 ± 6.3 nm and a PDI average of 0.22. The zeta potential ranged between 5 and 20 mV. The [{sup 153}Sm]Sm{sub 2}O{sub 3} loaded PLGA nanoparticles, orally administered were distributed to most organs at low levels, indicating that there was absorption of nanoparticles. While the IV injected [{sup 153}Sm]Sm{sub 2}O{sub 3}-loaded PLGA nanoparticles exhibited the highest localization of nanoparticles in the spleen (8.63 %ID/g) and liver (3.07 %ID/g), confirming that nanoparticles are rapidly removed from the blood by the RES, leading to rapid uptake in the liver and spleen. From the biodistribution data obtained, it is clear that polymeric nanoscale delivery systems would be suitable for improving permeability and thus the bioavailability of therapeutic compounds.

sup 8 sup 9 Sr and sup 1 sup 5 sup 3 Sm-EDTMP therapy of disseminated skeletal metastasis

CERN Document Server

Zhang Jun Ning; Zhu Shou Peng

2001-01-01

A retrospective analysis was performed on 72 patients with disseminated skeletal metastasis to evaluate the effect of strontium-89 or samarium-153 EDTMP therapy. There existed 87.88% of clinical response, 12.12% of no response in the group treated with strontium-89 as compared with 90.24% of clinical response, 9.76% no response in one treated with samarium-153 EDTMP; and there were no correlation between the treatment results and the amounts of isotopes administrated. The results suggest that strontium-89 or samarium-153 EDTMP therapy is a method of first choice in the palliative treatment for disseminated skeletal metastasis

89Sr and 153Sm-EDTMP therapy of disseminated skeletal metastasis

International Nuclear Information System (INIS)

Zhang Junning; Hong Chengjiao; Zhu Shoupeng

2001-01-01

A retrospective analysis was performed on 72 patients with disseminated skeletal metastasis to evaluate the effect of strontium-89 or samarium-153 EDTMP therapy. There existed 87.88% of clinical response, 12.12% of no response in the group treated with strontium-89 as compared with 90.24% of clinical response, 9.76% no response in one treated with samarium-153 EDTMP; and there were no correlation between the treatment results and the amounts of isotopes administrated. The results suggest that strontium-89 or samarium-153 EDTMP therapy is a method of first choice in the palliative treatment for disseminated skeletal metastasis

{sup 89}Sr and {sup 153}Sm-EDTMP therapy of disseminated skeletal metastasis

Energy Technology Data Exchange (ETDEWEB)

Junning, Zhang; Chengjiao, Hong; Shoupeng, Zhu [Suzhou Univ., Suzhou (China)

2001-07-01

A retrospective analysis was performed on 72 patients with disseminated skeletal metastasis to evaluate the effect of strontium-89 or samarium-153 EDTMP therapy. There existed 87.88% of clinical response, 12.12% of no response in the group treated with strontium-89 as compared with 90.24% of clinical response, 9.76% no response in one treated with samarium-153 EDTMP; and there were no correlation between the treatment results and the amounts of isotopes administrated. The results suggest that strontium-89 or samarium-153 EDTMP therapy is a method of first choice in the palliative treatment for disseminated skeletal metastasis.

Fabrication of samarium strontium aluminate ceramic and deposition of thermal barrier coatings by air plasma spray process

Directory of Open Access Journals (Sweden)

Baskaran T

2018-01-01

Full Text Available Thermal barrier coatings (TBC with the metallic NiCrAlY bond coat are often used in many aircraft engines to protect superalloy components from high-temperature corrosion thereby to improve the life of gas turbine components. The search for new TBC material has been intensified in recent years due to lack of thermo-physical properties of conventionally used Yttria stabilized Zirconia (YSZ TBCs. Recently, the rare earth containing Samarium Strontium Aluminate (SSA based ceramic was proposed as a new TBC material due to its matching thermo-physical properties with the substrate. The present work focused on the synthesis of SSA ceramics for TBCs application and its coatings development on Ni-based superalloy Inconel 718 substrate by air plasma spray process. The X-ray photoelectron spectroscopy (XPS result confirmed the formation of single phase SSA ceramic after synthesis. The surface morphology of SSA TBCs is mainly composed of melted splats, semi and un-melted particles. The cross-sectional SEM micrographs did not show any spallation at the interface which indicated good mechanical interlocking between the bond coat and ceramic top coat. The Young’s modulus and hardness of SSA TBCs were found to be 80 and 6.1 GPa, respectively. The load-depth curve of SSA TBC showed good elastic recovery about 47 %.

Structural and superconducting properties of (Y,Gd)Ba2Cu3O7-δ grown by MOCVD on samarium zirconate buffered IBAD-MgO

International Nuclear Information System (INIS)

Stan, L; Holesinger, T G; Maiorov, B; Feldmann, D M; Usov, I O; DePaula, R F; Civale, L; Foltyn, S R; Jia, Q X; Chen, Y; Selvamanickam, V

2008-01-01

Textured samarium zirconate (SZO) films have been grown by reactive cosputtering directly on an ion beam assisted deposited (IBAD) MgO template, without an intermediate homoepitaxial MgO layer. The subsequent growth of 0.9 μm thick (Y,Gd)Ba 2 Cu 3 O 7-δ ((Y, Gd)BCO) films by metal organic chemical vapor deposition (MOCVD) yielded well textured films with a full width at half maximum of 1.9 0 and 3.4 0 for the out-of-plane and in-plane texture, respectively. Microstructural characterizations of the SZO buffered samples revealed clean interfaces. This indicates that the SZO not only provides a diffusion barrier, but also functions as a buffer for (Y, Gd)BCO grown by MOCVD. The achievement of self-field critical current densities (J c ) of over 2 MA cm -2 at 75.5 K is another proof of the effectiveness of SZO as a buffer on the IBAD-MgO template. The in-field measurements revealed an asymmetric angular dependence of J c and a shift of the ab-plane maxima due to the tilted nature of the template and (Y,Gd) 2 O 3 particles existing in the (Y, Gd)BCO matrix. The present results are especially important because they demonstrate that high temperature superconducting coated conductors with simpler architecture can be fabricated using commercially viable processes

Contribution of current carrier mobility variation to piezo-resistive effect in SmS

International Nuclear Information System (INIS)

Vasil'ev, L.N.; Kaminskij, V.V.

1999-01-01

The value of the contribution from the change in the current carriers mobility and pressure to the piezo-resistive effect value in the materials on the basis of the samarium, monosulfide is studied. The conclusion, that the value of the piezoresistance of comprehensive compression should not exceed 7x10 -3 MPa -1 at T=300 K, experimental data [ru

Determination of the speciation and bioavailability of samarium to Chlamydomonas reinhardtii in the presence of natural organic matter.

Science.gov (United States)

Rowell, Justine-Anne; Fillion, Marc-Alexandre; Smith, Scott; Wilkinson, Kevin J

2018-06-01

As technological interest and environmental emissions of the rare earth elements increase, it is becoming more important to assess their potential environmental impact. Samarium (Sm) is a lanthanide of intermediate molar mass that is used in numerous high-technology applications including wind turbines, solar panels, and electric vehicles. The present study relates the speciation of Sm determined in the presence of natural organic matter (NOM) to its bioavailability to the unicellular green alga Chlamydomonas reinhardtii. The free ion concentration was determined using a cation exchange resin (ion exchange technique) in dynamic mode and compared with thermodynamic modeling. Short-term biouptake experiments were performed in the presence of 4 types of NOM: Suwannee River fulvic acids, Pahokee Peat fulvic acids, Suwannee River humic acids, and a Luther Marsh dissolved organic matter isolate (90-95% humic acids). It was clearly shown that even a small amount of NOM (0.5 mg C L -1 ) resulted in a significant decrease (10 times) in the Sm internalization fluxes. Furthermore, complexation with humic acids (and the corresponding reduction in Sm bioavailability) was stronger than that with fulvic acids. The results showed that the experimentally measured (free) Sm was a better predictor of Sm internalization than either the total concentrations or the free ion concentrations obtained using thermodynamic modeling. Environ Toxicol Chem 2018;37:1623-1631. © 2018 SETAC. © 2018 SETAC.

Fluorescence properties of europium and samarium. beta. -diketonates and their use in fluorometry

Energy Technology Data Exchange (ETDEWEB)

Huang, H; Hiraki, K; Nishikawa, Y [Kinki Univ., Higashi-Osaka, Osaka (Japan). Faculty of Science and Technology

1981-01-01

Several europium and samarium ..beta..-diketonates (tta, ntfa, bfa) complexed with 1, 10-phenanthroline, or with trioctylphosphine oxide (topo) were synthesized. The fluorescence properties of these compounds in benzene or hexane have been studied. Absorption and fluorescence spectra, fluorescence quantum yield, fluorescence sensitivity index (F.S.I.), and fluorescence lifetime were measured. From the measurement of fluorescence lifetime of the ..beta..-diketonates, the velocity of radiative process (k sub(f)/phi sub(f)) has almost the same value for benzene and hexane solvent. The red fluorescence (Em. max. : 619 nm) of Eu(III) in these chelates is attributed to transitions from /sup 5/D/sub 0/ ..-->.. /sup 7/F/sub 2/ levels of this ion, and the three-band spectrum (Em. max. : 569 nm, 606 nm, 650 nm) indicates the transitions from the /sup 4/G sub(5/2) ..-->.. /sup 6/H sub(5/2), /sup 4/G sub(5/2) ..-->.. /sup 6/H sub(7/2), and /sup 4/G sub(5/2) ..-->.. /sup 6/H sub(9/2) levels of Sm(III), respectively. These spectra are not changed by any solvents and ligands. From the results, the fluorescence of the ..beta..-diketonates in organic solvent has been attributed to m* ..-->.. m luminescence transition. The complexes of Eu(III) and Sm(III) show radiative transition within orbitals, composed exclusively of 4f orbitals of rare earth ions (m* ..-->.. m radiative transition). Fluorinated ligands show better sensitivity than unfluorinated ligands, and the best sensitivity is obtained with TTA-phen system, and/or TTA-topo system for the spectrofluorometric determination of the two metals. In the case of Eu determination, 619 nm emission wavelength is used (the determinable range : 0.2 -- 10 ppb Eu), and in the case of Sm determination, 650 nm emission wavelength is adopted (the determinable range : 0.1 -- 1 ppm Sm), because of much higher sensitivity than the other two peaks (569, 606 nm) without interference from europium complex.

Carmen system: a code block for neutronic PWR calculation by diffusion theory with spacedependent feedback effects

International Nuclear Information System (INIS)

Ahnert, C.; Aragones, J.M.

1982-01-01

The Carmen code (theory and user's manual) is described. This code for assembly and core calculations uses diffusion theory (Citation), with feedback in the cross sections by zone due to the effects of burnup, water density, fuel temperature, Xenon and Samarium. The burnup calculation of a full cycle is solved in only an execution of Carmen, and in a reduced computer time. (auth.)

Retrospective evaluation of bone pain palliation after samarium-153-EDTMP therapy Avaliação retrospectiva do tratamento da dor óssea metastática com Samário-153-EDTMP

Directory of Open Access Journals (Sweden)

Marcelo Tatit Sapienza

2004-01-01

Full Text Available PURPOSE: The aim of this study was to evaluate the degree of metastatic bone pain palliation and medullar toxicity associated with samarium-153-EDTMP treatment. METHODS: Seventy-three patients with metastatic bone pain having previously undergone therapy with samarium-153-EDTMP (1 mCi/kg were retrospectively evaluated. Routine follow-up included pain evaluation and blood counts for 2 months after treatment. Pain was evaluated using a subjective scale (from 0 to 10 before and for 8 weeks after the treatment. Blood counts were obtained before treatment and once a week for 2 months during follow-up. Dosimetry, based upon the urinary excretion of the isotope, was estimated in 41 individuals, and the resulting radiation absorbed doses were correlated with hematological data. RESULTS: Reduction in pain scores of 75% to 100% was obtained in 36 patients (49%, with a decrease of 50% to 75%, 25% to 50%, and 0% to 25% in, respectively, 20 (27%, 10 (14%, and 7 (10% patients. There was no significant relationship between the pain response and location of the primary tumor (breast or prostate cancer. Mild to moderate myelosuppression was noted in 75.3% of patients, usually with hematological recovery at 8 weeks. The mean bone marrow dose was 347 ± 65 cGy, and only a weak correlation was found between absorbed dose and myelosuppression (Pearson coefficient = .4. CONCLUSIONS: Samarium-153-EDTMP is a valuable method for metastatic bone pain palliation. A mild to moderate and transitory myelosuppression is the main toxicity observed after samarium therapy, showing a weak correlation with dosimetric measures.OBJETIVO: O presente trabalho teve por objetivo avaliar o efeito paliativo da dor e a toxicidade medular associados ao tratamento com Samário-153-EDTMP em pacientes com metástases ósseas. MÉTODOS: O estudo foi realizado de forma retrospectiva, a partir do levantamento de prontuário de 178 pacientes submetidos a tratamento com 1mCi/kg de 153Sm

Studies on the rare earth complexes with pyridine derivatives and their N-oxide(II) - Synthesis and properties of fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with 2,2'-bipyridine-N,N'-dioxide

International Nuclear Information System (INIS)

Minyu, T.; Ning, T.; Yingli, Z.; Jiyuan, B.

1985-01-01

The solid complexes of rare earth nitrates perchlorates and thiocyanates with 2,2'-bipyridine-N,N'-dioxide (bipyO/sub 2/) have been reported. However, the corresponding complexes of other rear earth chlorides have not been investigated except lanthanum, cerium and yttrium. As an extension of our previous work on the synthesis of complexes of praseodymium and neodymium chlorides wiht bipoyO/sub 2/, the authors have now prepared fluorescent solid complexes of samarium, europium, gadolium and terbium chlorides with biphyO/sub 2/, using methanol as a reaction medium. The new synthesized compounds have been identified by means of elemental analysis, infrared spectrometry, conductometry, differential thermal analysis (DTA), thermogravimetry (TG) and X-ray powder diffraction

Multicentre trial on the efficacy and toxicity of single-dose samarium-153-ethylene diamine tetramethylene phosphonate as a palliative treatment for painful skeletal metastases in China

International Nuclear Information System (INIS)

Tian Jia-he; Zhang Jin-ming; He Yi-jie; Hou Qing-tian; Oyang Qiao-hong; Wang Jian-min; Chuan Ling

1999-01-01

A multicentre trial was organized in China as part of an international coordinated research project to study the efficacy and toxicity of single-dose samarium-153 ethylene diamine tetramethylene phosphonate (EDTMP) as a palliative treatment for painful skeletal metastases. One hundred and five patients with painful bone metastases from various primaries were treated with 153 Sm-EDTMP at a dose of 37 MBq/kg(group I) or 18.5 MBq/kg (group II). The effects were evaluated according to change in daily analgesic consumption, pain score, sum of effect product (SEP), Physician's Global Assessment (PGA), blood counts, and organ function tests conducted regularly for 16 weeks. Fifty-eight of 70 patients in group I and 30 of 35 in group II had a positive response, with SEPs of 22.29±14.47 and 20.13±13.90 respectively. Of 72 patients who had been receiving analgesics, 63 reduced their consumption. PGA showed that the Karnofsky score (KS) increased from 58.54±25.90 to 71.67±26.53, indicating improved general condition, but the difference was not significant. Among subgroups of patients, only those with breast cancer showed a significant change in the Karnofsky score after treatment. Inter-group differences were found for net change in KS between patients with lung and patients with breast cancer, and between patients with lung and patients with oesophageal cancer. Seventeen patients showed no response. No serious side-effects were noted, except for falls in the white blood cell (nadir 1.5 x 10 9 /l) and platelet (nadir 6.0 x 10 10 /l) counts in 44/105 and 34/105 cases, respectively. Ten patients had an abnormal liver function test. Response and side-effects were both independent of dose. In conclusion, 153 Sm-EDTMP provided effective palliation in 83.8% of patients with painful bone metastases; the major toxicity was temporary myelosuppression. Further studies are needed to identify better ways of determining the appropriate dose in the individual case and the efficacy of

Pharmacokinetics of labelled compounds with technetium-99m and samarium-153; Farmacocinetica de compuestos marcados con tecnecio-99m y samario-153

Energy Technology Data Exchange (ETDEWEB)

Borda O, L B; Torres L, M N

1997-07-01

The purpose of this investigation was to establish the different pharmacokinetics parameters of the main radiopharmaceuticals labeled with technetium-99m and samarium-153. These parameters could be subsequently used as reference to compare other products with the same use. Mathematical models and a computerized pharmacokinetic program were used to this purpose. A biodistribution study in quadruplicate and/or quintuplicate was conducted for each radiopharmaceutical, data was was obtained in injection dose percentages. The biodistribution study involved the injection of a predetermined dose of the radiopharmaceutical into animals (rats or mice), which were subsequently put away at different time intervals, removing the relevant organs. Activity in each organ was read by means of a well-type NaI scintillation counter, data obtained in activity counts was transformed into injection dose percentages. Based on these percentages, the mathematical model was constructed and the pharmacokinetic parameters were obtained using the computerized program Expo 2 v. 1, which is written in C language and works in windows. Analyzing the results obtained, we can conclude that the use of the Expo 2 v. 1 program for a bi compartmental analysis allowed us to obtain reliable pharmacokinetic parameters which describe what happens in the organism when the radiopharmaceutical passes from the central compartment to the peripheral one and vice versa.

HF Propagation Effects Caused by an Artificial Plasma Cloud in the Ionosphere

Science.gov (United States)

Joshi, D. R.; Groves, K. M.; McNeil, W. J.; Caton, R. G.; Parris, R. T.; Pedersen, T. R.; Cannon, P. S.; Angling, M. J.; Jackson-Booth, N. K.

2014-12-01

In a campaign carried out by the NASA sounding rocket team, the Air Force Research Laboratory (AFRL) launched two sounding rockets in the Kwajalein Atoll, Marshall Islands, in May 2013 known as the Metal Oxide Space Cloud (MOSC) experiment to study the interactions of artificial ionization and the background plasma and measure the effects on high frequency (HF) radio wave propagation. The rockets released samarium metal vapor in the lower F-region of the ionosphere that ionized forming a plasma cloud that persisted for tens of minutes to hours in the post-sunset period. Data from the experiments has been analyzed to understand the impacts of the artificial ionization on HF radio wave propagation. Swept frequency HF links transiting the artificial ionization region were employed to produce oblique ionograms that clearly showed the effects of the samarium cloud. Ray tracing has been used to successfully model the effects of the ionized cloud. Comparisons between observations and modeled results will be presented, including model output using the International Reference Ionosphere (IRI), the Parameterized Ionospheric Model (PIM) and PIM constrained by electron density profiles measured with the ALTAIR radar at Kwajalein. Observations and modeling confirm that the cloud acted as a divergent lens refracting energy away from direct propagation paths and scattering energy at large angles relative to the initial propagation direction. The results confirm that even small amounts of ionized material injected in the upper atmosphere can result in significant changes to the natural propagation environment.

Structural and superconducting properties of (Y,Gd)Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} grown by MOCVD on samarium zirconate buffered IBAD-MgO

Energy Technology Data Exchange (ETDEWEB)

Stan, L; Holesinger, T G; Maiorov, B; Feldmann, D M; Usov, I O; DePaula, R F; Civale, L; Foltyn, S R; Jia, Q X [Los Alamos National Laboratory, PO Box 1663, Los Alamos, NM 87545 (United States); Chen, Y; Selvamanickam, V [SuperPower, Incorporated, 450 Duane Avenue, Schenectady, NY 12304 (United States)

2008-10-01

Textured samarium zirconate (SZO) films have been grown by reactive cosputtering directly on an ion beam assisted deposited (IBAD) MgO template, without an intermediate homoepitaxial MgO layer. The subsequent growth of 0.9 {mu}m thick (Y,Gd)Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} ((Y, Gd)BCO) films by metal organic chemical vapor deposition (MOCVD) yielded well textured films with a full width at half maximum of 1.9{sup 0} and 3.4{sup 0} for the out-of-plane and in-plane texture, respectively. Microstructural characterizations of the SZO buffered samples revealed clean interfaces. This indicates that the SZO not only provides a diffusion barrier, but also functions as a buffer for (Y, Gd)BCO grown by MOCVD. The achievement of self-field critical current densities (J{sub c}) of over 2 MA cm{sup -2} at 75.5 K is another proof of the effectiveness of SZO as a buffer on the IBAD-MgO template. The in-field measurements revealed an asymmetric angular dependence of J{sub c} and a shift of the ab-plane maxima due to the tilted nature of the template and (Y,Gd){sub 2}O{sub 3} particles existing in the (Y, Gd)BCO matrix. The present results are especially important because they demonstrate that high temperature superconducting coated conductors with simpler architecture can be fabricated using commercially viable processes.

Kondo effect and non-Fermi liquid behavior in metallic glasses containing Yb, Ce, and Sm

Science.gov (United States)

Huang, B.; Yang, Y. F.; Wang, W. H.

2013-04-01

The low temperature properties of metallic glasses containing different concentrations of ytterbium, cerium, and samarium are studied. It is found that the Kondo effect caused by exchange interactions between the conduction and 4f electrons and non-Fermi liquid behavior appear in the strongly disordered alloys. We study the origins for these unique features and demonstrate that the found Kondo effect is inherited from the crystalline counterparts. The results might have significance on investigating the strong electron-electron interaction systems with structural disorder and be helpful for designing new metallic glasses with functional properties.

Thermodynamics and statistical mechanics of some hydrides of the lanthanides and actinides

International Nuclear Information System (INIS)

Mintz, M.H.

1976-06-01

This work deals mainly with the thermodynamic and physical properties of the hydrides of the lanthanides and actinides. In addition, statistical models have been developed and applied to metal-hydrogen systems. A kinetic study of the uranium-hydrogen system was performed. The thermodynamic properties of the hydrides of neptunium, thorium, praseodymium, neodymium, samarium and europium were determined. In addition the samarium-europium-hydrogen ternary system was investigated. Moessbauer effect measurements of cubic neptunium hydrides were interpreted according to a model presented. A comparison. (author)

Synergistic Effects of Sm and C Co-Doped Mixed Phase Crystalline TiO2 for Visible Light Photocatalytic Activity

Directory of Open Access Journals (Sweden)

Fuchang Peng

2017-02-01

Full Text Available Mixed phase TiO2 nanoparticles with element doping by Sm and C were prepared via a facile sol-gel procedure. The UV-Vis light-diffuse reflectance spectroscopy analysis showed that the absorption region of co-doped TiO2 was shifted to the visible-light region, which was attributed to incorporation of samarium and carbon into the TiO2 lattice during high-temperature reaction. Samarium effectively decreased the anatase-rutile phase transformation. The grain size can be controlled by Sm doping to achieve a large specific surface area useful for the enhancement of photocatalytic activity. The photocatalytic activities under visible light irradiation were evaluated by photocatalytic degradation of methylene blue (MB. The degradation rate of MB over the Sm-C co-doped TiO2 sample was the best. Additionally, first-order apparent rate constants increased by about 4.3 times compared to that of commercial Degusssa P25 under the same experimental conditions. Using different types of scavengers, the results indicated that the electrons, holes, and •OH radicals are the main active species for the MB degradation. The high visible-light photocatalytic activity was attributed to low recombination of the photo-generated electrons and holes which originated from the synergistic effect of the co-doped ions and the heterostructure.

Optimal Timing of Bisphosphonate Administration in Combination with Samarium-153 Oxabifore in the Treatment of Painful Metastatic Bone Disease

International Nuclear Information System (INIS)

Rasulova, Nigora; Lyubshin, Vladimir; Arybzhanov, Dauranbek; Sagdullaev, Sh.; Krylov, Valery; Khodjibekov, Marat

2013-01-01

While bisphosphonates are indicated for prevention of skeletal-related events, radionuclide therapy is widely used for treatment of painful bone metastases. Combined radionuclide therapy with bisphosphonates has demonstrated improved effectiveness in achieving bone pain palliation in comparison to mono therapy with radionuclides or bisphosphonates alone. However, there are conflicting reports as to whether bisphosphonates adversely influence skeletal uptake of the bone-seeking radiotracers used for therapy. Recent studies analyzing influence of Zoledronic acid on total bone uptake of Samarium-153 EDTMP (Sm-153 EDTMP) by measuring cumulative urinary activity of Sm-153 on baseline study, as well as in combination with bisphosphonates (administrated 48 hours prior to Sm-153) did not provide any statistically significant difference in urinary excretion of Sm-153 between the two groups. It may be noted that the exact temporal sequence of bisphosphonate administration vis a vis radionuclide therapy has not yet been studied. One of the side effects of bisphosphonates is transient flare effect on bone pain. Radionuclide therapy may also have similar side effect. Keeping in view the above the current study was designed with the main objective of determining the exact timing of bisphosphonate administration in patients receiving combined therapy so as to achieve optimal efficacy of bone pain palliation. Ninety-three patients suffering from metastatic bone pain who received combination therapy with Sm-153 oxabifore (an analog of Sm-153 EDTMP) and Zoledronic acid were divided into three groups according to the timing of Zoledronic acid administration: Group I: 39 patients who received Zoledronic acid 7 or more days prior to Sm-153 oxabifore treatment; Group II: 32 patients who received Zoledronic acid 48-72 hours prior to Sm-153 oxabifore treatment and Group III: 22 patients who received Zoledronic acid 7 days after Sm-153 oxabifore treatment. Sm-153 oxabifore was administered

Sorption of samarium in soils: influence of soil properties and Sm concentration

Energy Technology Data Exchange (ETDEWEB)

Ramirez-Guinart, Oriol; Salaberria, Aitor; Rigol, Anna; Vidal, Miquel [Analytical Chemistry department, Faculty of Chemistry, University of Barcelona, Marti i Franques 1-11, 08028, Barcelona (Spain)

2014-07-01

Due to the fact that barriers of Deep Geological Repositories (DGR) may lose efficiency before the radioisotopes present in the High Level Radioactive Waste (HLRW) completely decay, it is possible that, in the long-term, radioactive leachates may escape from the DGR and reach the soil and water compartments in the biosphere. Therefore, it is required to examine the interaction and mobility of radionuclides present in the HLRW, or their chemical analogues, to predict the impact of their eventual incorporation in the biosphere and to assess the derived risk. Although relevant data have been recently obtained for a few radionuclides in soils, there are still some important gaps for some radionuclides, such us for samarium (Sm). Sm is a lanthanide that, besides being considered as a natural analogue of actinides, may also be present in HLRW in the form of the radioactive isotope {sup 151}Sm. The main objective of this work was to obtain sorption data (K{sub d}) of {sup 151}Sm gathered from a set of soil samples physicochemical fully-characterized (pH, texture, cationic exchange capacity, soil solution cationic composition, organic matter, carbonate and metallic oxides content, etc.). Additionally, as an alternative for testing sorption capacity of radionuclides in soils is the use of the corresponding stable isotope or a chemical analogue, the influence of Sm concentration was also checked. To evaluate {sup 151}Sm sorption, batch assays were carried out for each soil sample, which consisted in a pre-equilibration step of 2 g of each soil with 50 ml of double deionised water, and a subsequent equilibration step with the same solution, but labelled with {sup 151}Sm. The activity of {sup 151}Sm in initial and final solutions was measured by liquid scintillation and K{sub d} ({sup 151}Sm) data were calculated. The reversibly sorbed fraction was estimated by the application of a single extraction test, with double deionised water, to soil residues coming from the previous

Effect Of Neutron Activation Factor On The Physico-Chemical Properties Of Hydrophilic And Hydrophobic Polymer Formulation Of Matrix Tablets

International Nuclear Information System (INIS)

Ibrahim Ijang; Bohari Yaacob; Nordiana, N.R.

2011-01-01

This study was to investigate effect of neutron activation on the physicochemical properties and in vitro dissolution of sustained-release matrix tablets. The tablets incorporation of Samarium oxide (Sm 2 O 3 ) and were compared before and after irradiation with thermal neutron for 5 minutes at 1.2 x 10 12 neutron cm -2 s -1 . The neutron activation factor did not influence the compression properties of the tablets. The dissolution tests showed that irradiation increased the release of the model drug ketoprofen from the tablets. This effect might be explained by polymer degradation. Incorporation of Sm 2 O 3 in the matrix tablets did not influence the release. (author)

Stable isotope tracer marking of individual boll weevils

International Nuclear Information System (INIS)

James, W.D.; Showler, A.T.; Armstrong, J.S.; Westbrook, J.K.

2006-01-01

Stable isotope markers have been used to study animal nutrition for several decades and more recently to study the foraging and cultural habits of imported fire ants. In this work, we have extended that effort to evaluate the potential for marking boll weevils, Anthonomus grandis grandis Boheman (Coleoptera: Curculionidae), with the rare earth element samarium to aid in studies of insect invasion and pest eradication protocols. Neutron activation analysis (NAA) was performed on the marked boll weevils as well as plant material from the cotton squares on which the insects were fed. Samarium levels in non-dosed insects average about 20 ng/g or about 100 pg total element per insect. Our computed average determination limit was 36 pg samarium/weevil. The determination limit for cotton plant squares and leaves averaged 3.5 ng/g and 8.2 ng/g, respectively. These initial results indicate the NAA method is capable of identifying individual marked insects which have assimilated 1 ng of samarium, a ten-fold increase in content over average blank values. (author)

The Level of Europium-154 Contaminating Samarium-153-EDTMP Activates the Radiation Alarm System at the US Homeland Security Checkpoints

Directory of Open Access Journals (Sweden)

Mohammed Najeeb Al Hallak

2009-08-01

Full Text Available 153Sm-EDTMP is a radiopharmaceutical composed of EDTMP (ethylenediamine-tetramethylenephosphonate and Samarium-153 [1]. 153Sm-EDTMP has an affinity for skeletal tissue and concentrates in areas with increased bone turnover; thus, it is successfully used in relieving pain related to diffuse bone metastases [1]. The manufacturing process of 153Sm-EDTMP leads to contamination with 154Eu (Europium-154 [2]. A previous study only alluded to the retention of 154Eu in the bones after receiving treatment with 153Sm-EDTMP [2]. Activation of the alarm at security checkpoints after 153Sm-EDTMP therapy has not been previously reported. Two out of 15 patients who received 153Sm-EDTMP at Roger Maris Cancer Center (Fargo, N. Dak., USA activated the radiation activity sensors while passing through checkpoints; one at a US airport and the other while crossing theAmerican-Canadian border. We assume that the 154Eu which remained in the patients’ bones activated the sensors. Methods: In order to investigate this hypothesis, we obtained the consent from 3 of our 15 patients who received 153Sm-EDTMP within the previous 4 months to 2 years, including the patient who had activated the radiation alarm at the airport. The patients were scanned with a handheld detector and a gamma camera for energies from 511 keV to 1.3 MeV. Results: All three patients exhibited identical spectral images, and further analysis showed that the observed spectra are the result of 154Eu emissions. Conclusion: Depending on the detection thresholds and windows used by local and federal authorities, the remaining activity of 154Eu retained in patients who received 153Sm-EDTMP could be sufficient enough to increase the count rates above background levels and activate the sensors. At Roger Maris Cancer Center, patients are now informed of the potential consequences of 153Sm-EDTMP therapy prior to initiating treatment. In addition, patients treated with 153Sm-EDTMP at Roger Maris Cancer Center

2. Home 3. Journals 4. Bulletin of Materials Science 5. Volume 28 6 ...

Indian Academy of Sciences (India)

483. Acceptor. Study on electrical properties of Ni-doped SrTiO3 ceramics .... Effect of Cr and Ni on diffusion bonding of Fe3Al with steel. 63. Creep ... Oriented growth of thin films of samarium oxide by MOCVD. 49 .... Grain boundary. Study on ...

Effect of Samarium Oxide on the Electrical Conductivity of Plasma-Sprayed SOFC Anodes

Science.gov (United States)

Panahi, S. N.; Samadi, H.; Nemati, A.

2016-10-01

Solid oxide fuel cells (SOFCs) are rapidly becoming recognized as a new alternative to traditional energy conversion systems because of their high energy efficiency. From an ecological perspective, this environmentally friendly technology, which produces clean energy, is likely to be implemented more frequently in the future. However, the current SOFC technology still cannot meet the demands of commercial applications due to temperature constraints and high cost. To develop a marketable SOFC, suppliers have tended to reduce the operating temperatures by a few hundred degrees. The overall trend for SOFC materials is to reduce their service temperature of electrolyte. Meanwhile, it is important that the other components perform at the same temperature. Currently, the anodes of SOFCs are being studied in depth. Research has indicated that anodes based on a perovskite structure are a more promising candidate in SOFCs than the traditional system because they possess more favorable electrical properties. Among the perovskite-type oxides, SrTiO3 is one of the most promising compositions, with studies demonstrating that SrTiO3 exhibits particularly favorable electrical properties in contrast with other perovskite-type oxides. The main purpose of this article is to describe our study of the effect of rare-earth dopants with a perovskite structure on the electrical behavior of anodes in SOFCs. Sm2O3-doped SrTiO3 synthesized by a solid-state reaction was coated on substrate by atmospheric plasma spray. To compare the effect of the dopant on the electrical conductivity of strontium titanate, different concentrations of Sm2O3 were used. The samples were then investigated by x-ray diffraction, four-point probe at various temperatures (to determine the electrical conductivity), and a scanning electron microscope. The study showed that at room temperature, nondoped samples have a higher electrical resistance than doped samples. As the temperature was increased, the electrical

Investigation of doped Perovskite systems RAIO3 using density functional theory based electronic structure and thermoelectric studies

International Nuclear Information System (INIS)

Sandeep; Ghimire, M. P.; Thapa, R. K.; Rai, D. P.; Shankar, A

2016-01-01

Samarium doping effects on the thermoelectric properties in Eu 1-x Sm x AlO 3 (x=0%, 50%, and 100%) were studied using first principles calculations based thermal transport property measurement. The result indicate that the compound is an intrinsic n-type material. Samarium doping has a positive effect on the overall thermoelectric performance of the Eu 1-x Sm x AlO 3 system, with sharp increase in figure of merit (ZT) observed when x=0, 50 and 100% up to 150K. Compared to x=0 and 100%, the case of x=50% was found to have more positive increment in ZT value suggesting that the doing to have positive effect on figure of merit in Eu 1-x Sm x AlO 3 . Furthermore, all the samples show stable thermoelectric compatibility factors over a broad temperature range from 700 to 1000 K, which could have great benefits for their practical applications. It is concluded that the overall thermoelectric performance of the Eu 1-x Sm x AlO 3 could be highly enhanced using doping techniques. (paper)

Microwave studies on the dielectric properties of Sm3+ and Sm3+/CdTe doped sol-gel silica glasses

International Nuclear Information System (INIS)

Mathew, Siby; Rejikumar, P.R.; Yohannan, Jaimon; Mathew, K.T.; Unnikrishnan, N.V.

2008-01-01

Complex permittivity and conductivity studies of Samarium and Samarium/semiconductor cadmium telluride sol-gel silica glass samples were done. We use cavity perturbation technique at S band frequencies using TE 10p Mode. Structural evolution of the matrix on annealing is discussed based on FTIR analysis/XRD power diffraction. In cavity perturbation technique dielectric parameters like complex permittivity and conductivity are determined by measuring changes in resonant frequency due to small perturbation inside the cavity produced by the introduction of the samples. The addition of the semiconductor along with the samarium was found to lower the permittivity, loss factor and conductivity. Variations of permittivity values with annealing temperature find applications in IC Technology, optic fibre communication, etc. The Sm 3+ /CdTe doped glasses can also be used in the fabrication of new and improved materials for microwave electronic circuits and in electromagnetic shielding devices

Udvikling af materialer til brintpermeable membraner

DEFF Research Database (Denmark)

Bentzer, Henrik Karnøe

doped samarium titanate, lanthanum magnesium titanate and strontium cerate doped with yttrium and nickel. Concentration cell measurements were used to estimate transport numbers for protons and oxide ions in yttrium doped strontium cerate and calcium doped samarium titanate. Furthermore, the voltage......Due to global warming as well as other factors, it is necessary to find alternatives to the current consumption of fossil fuels. Oxide materials with high protonic conductivity can potentially find application within many different technological fields in a society that is based on renewable energy...

Contribution to the study of the diffusion of fission products in uranium; Contribution a l'etude de la diffusion des produits de fission dans l'uranium

Energy Technology Data Exchange (ETDEWEB)

Tournier, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-10-15

In this work we have developed a simple method for determining the diffusion constants and the solid-state solubilities of a metal which is volatile and only slightly soluble in second metal. This method has been applied to the behaviour of certain fission products in {gamma} uranium: strontium, barium, lanthanum, samarium and cerium. This work has made it possible to show the effect of the atomic radius of the solute on the diffusion constants. (author) [French] Dans ce travail nous avons mis au point une methode simple permettant de determiner les constantes de diffusion ainsi que les solubilites a l'etat solide d'un metal volatil et peu soluble dans un autre. Cette methode a ete appliquee au comportement de certains produits de fission dans l'uranium {gamma}: strontium, baryum, lanthane, samarium et cerium. Cette etude a permis de mettre en evidence le role du rayon atomique du solute sur les constantes de diffusion. (auteur)

Effect of samaria-doped ceria (SDC) interlayer on the performance of La0.6Sr0.4Co0.2Fe0.8O3-δ/SDC composite oxygen electrode for reversible solid oxide fuel cells

International Nuclear Information System (INIS)

Shimura, Kazuki; Nishino, Hanako; Kakinuma, Katsuyoshi; Brito, Manuel E.; Uchida, Hiroyuki

2017-01-01

In order to establish clear criteria for designing highly active and highly durable oxygen electrode for reversible solid oxide fuel cells, we have focused on the effect of samaria-doped ceria (SDC) interlayers prepared on YSZ solid electrolyte surface on the performances of La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF)-SDC composite oxygen electrode. Symmetrical cells with the configuration, LSCF-SDC|SDC interlayer|YSZ|SDC interlayer|LSCF-SDC, were constructed. We prepared two kinds of SDC interlayers, one from a mixed solution of cerium 2-ethylhexanoate (denoted as octoate) and samarium octoates (o-interlayer) and another from a mixed solution of cerium and samarium nitrates (n-interlayer). The LSCF-SDC electrodes with o-interlayer and n-interlayer exhibited very similar performances in both the anodic and cathodic reactions at 900 °C. When temperature was decreased to 800 °C, an increase in overpotentials was observed. However, the LSCF-SDC electrode with o-interlayer exhibited superior performance to that with n-interlayer. It was found that the entire surface of the YSZ electrolyte disk was well covered with a dense o-interlayer of uniform thickness. Such an interlayer enables uniform transport of oxide ions to and from the LSCF-SDC electrode, resulting in an enlarged effective reaction zone (ERZ). The I-E performance of the LSCF-SDC|o-interlayer|YSZ cell was found to be comparable to that of the identical electrode prepared on a dense SDC sintered electrolyte disk (as a reference). This observation supports our views regarding the essential role of a dense interlayer with uniform thickness in enhancing the performance of reversible solid oxide cells.

Influence of extragent dilution upon light rare earths separation

International Nuclear Information System (INIS)

Korpusova, R.D.; Smirnova, N.N.

1978-01-01

The effect of diluting the extragent on separation of REE in the presence of 6 g-equiv. of LiNO 3 has been studied. For experiments use was made of TBP diluted with kerosene or butylbenzene (40,50,70 vol.%). The separation coefficients have been determined under conditions of saturation. The content of trace amounts of the components has been determined by the weight method; the content of macroimpurities - by the radiometric method. It has been established that the coefficient of Ce-La, Pr-La separation is not affected by the dilution of the extragent. The only exception is the Pr 142 -La pair; in the presence of trace amounts of better extracted element and two-fold dilution the separation coefficient increases almost by 150%. For the Pr-Ce pair the effect of dilution is better noticeable in that case when more extracted element is present in trace amounts. However, a comparison of the effect of dilution on separation coefficients of all REE pairs under study has shown that this effect is the strongest for the samarium-neodymium pair. The data obtained allow an assumption to be made that kerosene, as a diluent, affects the steric factor and coordination. Therefore, upon dilution the coefficient of the samarium-neodymium pair separation is affected most of all

Valency state changes in lanthanide-contained systems under high pressure

Energy Technology Data Exchange (ETDEWEB)

Jayaraman, A

1980-08-01

Changes in valency state induced by pressure in samarium sulphide SmS remind one of alchemy, as the mat black initial substance shines golden after the electron transition. The alchemist's dream is of course not realized, however the compound does exhibit an unusually interesting behaviour in the new state. The valency state of samarium as newly appeared fluctuated very rapidly between two electron configurations. Manipulation of the valency state by pressure or chemical substitution can basically change the physical properties of systems containing lanthanides. The phenomena are described and discussed in the following survey.

Neutron capture cross section measurement of $^{151}Sm$ at the CERN neutron Time of Flight Facility (nTOF)

CERN Document Server

Abbondanno, U; Alvarez-Velarde, F; Alvarez-Pol, H; Andriamonje, Samuel A; Andrzejewski, J; Badurek, G; Baumann, P; Becvar, F; Benlliure, J; Berthoumieux, E; Calviño, F; Cano-Ott, D; Capote, R; Cennini, P; Chepel, V; Chiaveri, Enrico; Colonna, N; Cortés, G; Cortina-Gil, D; Couture, A; Cox, J; Dababneh, S; Dahlfors, M; David, S; Dolfini, R; Domingo-Pardo, C; Durán, I; Embid-Segura, M; Ferrant, L; Ferrari, A; Ferreira-Marques, R; Frais-Kölbl, H; Furman, W; Gonçalves, I; Gallino, R; Gonzalez-Romero, E; Goverdovski, A; Gramegna, F; Griesmayer, E; Gunsing, F; Haas, B; Haight, R; Heil, M; Herrera-Martínez, A; Isaev, S; Jericha, E; Kappeler, F; Kadi, Y; Karadimos, D; Kerveno, M; Ketlerov, V; Köhler, P; Konovalov, V; Krticka, M; Lamboudis, C; Leeb, H; Lindote, A; Lopes, I; Lozano, M; Lukic, S; Marganiec, J; Marrone, S; Martinez-Val, J; Mastinu, P; Mengoni, A; Milazzo, P M; Molina-Coballes, A; Moreau, C; Mosconi, M; Neves, F; Oberhummer, Heinz; O'Brien, S; Pancin, J; Papaevangelou, T; Paradela, C; Pavlik, A; Pavlopoulos, P; Perlado, J M; Perrot, L; Pignatari, M; Plag, R; Plompen, A; Plukis, A; Poch, A; Policarpo, Armando; Pretel, C; Quesada, J; Raman, S; Rapp, W; Rauscher, T; Reifarth, R; Rosetti, M; Rubbia, Carlo; Rudolf, G; Rullhusen, P; Salgado, J; Soares, J C; Stéphan, C; Tagliente, G; Taín, J L; Tassan-Got, L; Tavora, L; Terlizzi, R; Vannini, G; Vaz, P; Ventura, A; Villamarín, D; Vincente, M C; Vlachoudis, V; Voss, F; Wendler, H; Wiescher, M; Wissha, K

2004-01-01

The measurement of **1**5**1Sm(n, gamma)**1**5**2Sm (samarium) cross section showed improved performance of the new spallation neutron facility. It covered a wide energy range with good resolution, high neutron flux, low backgrounds and a favourable duty factor. The samarium cross section was found to be of great importance for characterizing neutron capture nucleosynthesis in asymptotic giant stars. The combination of these features provided a promising basis for a broad experimental program directed towards application in astrophysics and advanced nuclear technologies. (Edited abstract)

Radiochemical and biological studies, including in non-human primates, towards indigenous development of 153Sm-EDTMP for metastatic bone pain palliation

International Nuclear Information System (INIS)

Saraswathy, P.; Mehra, K.S.; Ranganatha, D.K.; Das, M.K.; Balasubramanian, P.S.; Ananthakrishnan, M.; Ramamoorthy, N.; Gunasekaran, S.; Shanthly, N.; Retna Ponmalar, J.; Narasimhan, S.

2001-01-01

The combination of ease of formulation and superior biological features of 153 Sm-EDTMP in terms of safety and efficacy for metastatic bone pain palliation, together with the prospect of better logistics of production, has prompted extensive efforts by many groups world over for its preparation and evaluation. Our efforts have been directed towards exploring the feasibility for formulation of 153 Sm-EDTMP suitable for human use by neutron activation in medium flux reactors of the freely available and inexpensive natural samarium oxide target. The emphasis in biological studies was placed on tests in larger animals (monkeys) as a prelude to clinical evaluation. Feasibility to achieve reasonably high specific activity of 300-700 mCi/mg Sm at EOB with natural samarium has been adequately demonstrated. The radioeuropium contamination, estimated by γ-spectrometry to be 153 Sm-EDTMP from natural samarium at high radioactive concentrations of 40-50 mCi 153 Sm/mL, acceptable biolocalization, as revealed by both biodistribution studies in rats (femur uptake of 2-3% injected dose at 1h p.i. and retention up to 120 h p.i.) and gamma camera images in monkeys and adequate stability have been feasible. Excellent quality bone images of monkeys were recorded showing rapid clearance from blood, visualization of skeleton, clearance from kidneys within 2 hours and retention in skeleton up to 116 hours p.i. No significant activity in other soft tissues was noted. Comparative evaluation of the product prepared from enriched samarium as well as using in-house synthesized EDTMP has, likewise, revealed identical biolocalization features. EDTMP dose tolerance test in mice showed a safety factor of about 100 for a product made from natural samarium at an adult human dose of 50 mCi 153 Sm. Feasibility for production, reasonable safety and satisfactory biolocalisation of the indigenous product has been adequately established so as to warrant clinical trials in patients. (author)

Photoluminescence and spectroscopic dependence of fluorophosphate glasses on samarium ions concentration and the induced defects by gamma irradiation

Energy Technology Data Exchange (ETDEWEB)

Marzouk, M.A., E-mail: marzouk_nrc@yahoo.com [Glass Research Department, National Research Centre, 33 El Bohouth Street (former EL Tahrir), P.O. 12622, Dokki, Giza (Egypt); Hamdy, Y.M. [Spectroscopy Department, National Research Centre, 33 El Bohouth Street (former EL Tahrir), P.O. 12622, Dokki, Giza (Egypt); ElBatal, H.A. [Glass Research Department, National Research Centre, 33 El Bohouth Street (former EL Tahrir), P.O. 12622, Dokki, Giza (Egypt); Ezz ElDin, F.M. [National Institute for Radiation Research & Technology, Nasr City, Cairo (Egypt)

2015-10-15

/2} and {sup 6}H{sub 11/2}, respectively. The intensity of the emission spectra is observed to increase with the increase of Sm{sub 2}O{sub 3} content. The optical spectra within the visible–near IR region and photoluminescence spectra of Sm{sub 2}O{sub 3}-doped glasses are found to be stable and show almost no variations after gamma irradiation especially when rare-earth ions are present in noticeable contents (1–3%). FTIR spectra of all the studied glasses reveal repetitive and characteristic vibrational bands mainly due to phosphate groups with abundant of Q{sup 2} and Q{sup 3} groups due to the high content of P{sub 2}O{sub 5} (70 mol%). The introduction of 10% NaF and 20% AlF{sub 3} is observed to cause formation of mixed fluorophosphate groups (PO{sub 3}F){sup 2−}. The formation of (AlPO){sub 4} and/or (AlPO{sub 6}) groups needs further justification by combined techniques. The increase of Sm{sub 2}O{sub 3} content to 3% causes obvious increase of the IR absorption bands within the wavenumbers range of about 850–1400 cm{sup −1} due to suggested depolymerization effect. Gamma irradiation causes no distinct variations in the FTIR spectra due to suggested compactness through the formation of additional structural groups from AlF{sub 4} or AlF{sub 6}. - Highlights: • Samarium ions doped in host fluorophosphate glasses were prepared. • Optical and FT infrared absorption techniques were applied to study the spectral properties of the glasses. • Photoluminescence properties were measured. • Collective spectroscopic variations generated by gamma irradiation were investigated.

Reactive Materials for Evaporating Samarium (Pre-Print)

Science.gov (United States)

2016-04-15

further below  in  the  sample were not effectively  heated  and did not ignite.   Heat   transfer  was improved in pressed  pellets, which were, therefore...particles.  This combustion regime is most desired  for Sm  evaporation  based on the measured mass of the remaining coarse  condensed  combustion  products...the  evaporated  Sm could  condense  on top of the cooled burned out pellet,  forming  the surface coating.   Further EDX characterization qualitatively

Nuclear study of Melusine; Etude nucleaire de Melusine

Energy Technology Data Exchange (ETDEWEB)

Cherot, J [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

In this report are reviewed - with respect to starting of experiments - the main nuclear characteristics of a 20 per cent enriched uranium lattice, with light water as moderator and reflector. The reactor is to operate at 1 MW. 1) Study of various critical masses. 2) Control. Effectiveness of cadmium. Control rods and of a stainless steel regulating rod. 3) Study of the effect on reactivity of disturbances in the core center. 4) Study of xenon and samarium poisoning. 5) Temperature factor. 6) Heat exchanges in a fuel element. (author) [French] On etudie, dans ce rapport, les principales proprietes nucleaires d'un reseau a uranium enrichi (20 pour cent), dont le moderateur et le reflecteur sont l'eau legere en vue des experiences de demarrage. Ce reacteur devra fonctionner a 1 MW. 1) Etude de diverses masses critiques. 2) Controle. Efficacite des barres de controle en cadmium et d'une barre de reglage en acier inoxydable. 3) Etude de l'effet sur la reactivite de perturbation au centre du coeur. 4) Etude de l'empoisonnement xenon et samarium. 5) Coefficient de temperature. 6) Echanges thermiques dans un element. (auteur)

Influence of rare earth elements on radiation defect formation in silicon

International Nuclear Information System (INIS)

Nazyrov, D.E.

2006-01-01

Full text: It is known that efficiency of form and kinetics annealing of radiation defects influence greatly presence of initial in controlling electrically active or inactive impurities, their concentration and position in a lattice of a semiconductor. From this point of view of impurities of group of rare earths elements (REE) are of great interest, they interact with primary radiation defects creating electrically passive complexes such as . Thus they increase radiation stability of silicon. The purpose of the given work was the investigation of effect of irradiation by γ-quanta 60 Co properties of silicon doped REE-by samarium, gadolinium and erbium. The doping of silicon was carried out by growth process. Concentration of REE - samarium, gadolinium and erbium in silicon according to neutron-activation analysis equaled 10 14 /5·10 18 cm 2 . Silicon doped by phosphorus - 15/50 Ωcm were used as control samples. The results of investigations were obtained from DLTS (deep level transient spectroscopy) measurements, Hall effect and electrical measurements on definition of a resistivity, lifetime of minority carriers of a charge and optically active of concentrations of oxygen and carbon. The optical recharge by the infrared light emitting diode (P=10 mV, λ=0,95 μm) was used for investigation of deep levels (DL) situated in lower half of band gap. In control samples irradiated by the γ-quanta 60 Co with a dose 10 16 / 5·10 18 cm -2 formation DL was found in band, the parameters of which are well-known: A-, E-centers etc. Depending on a dose of an effect of irradiate in an energy spectrum of radiation defects in Si of essential changes, except for concentration is not observed. The deep levels concentration the E c -0,17 eV and E c -0,4 eV in Si is essentially reduced with respect control samples. The comparison the dose of associations of observable levels in irradiated n-Si with similar associations in control samples shows, that a velocity of introduction

Determination of the {sup 151}Sm half-life

Energy Technology Data Exchange (ETDEWEB)

Be, Marie-Martine; Cassette, Philippe [CEA, LIST, Gif sur Yvette (France). LNE-Laboratoire National Henri Becquerel; Isnard, Helene [CEA-LANIE, Gif sur Yvette (France); and others

2015-07-01

New measurements have been undertaken to determine the half-life of {sup 151}Sm. A pure {sup 151}Sm solution was obtained after chemical separation from a samarium solution resulting from the dissolution of an irradiated samarium sample. The concentration of {sup 151}Sm in the solution was measured by mass spectrometry, combined with the isotope dilution technique. The activity of the solution was measured by liquid scintillation counting by six European laboratories as part of an international comparison. These combined results lead to a half-life of T{sub 1/2} = 94.6(6)a.

Vaporization of Samarium trichloride studied by thermogravimetry

International Nuclear Information System (INIS)

Esquivel, Marcelo R.; Pasquevich, Daniel M.

2003-01-01

In the present work, the vaporization reaction of SmCl 3 (l) obtained from the 'in situ' reaction of Sm 2 O 3 (s) and Cl 2 (g)-C(s) was studied by thermogravimetry under controlled atmosphere. The effects of both the temperature between 825 C degrees and 950 C degrees and the total flow gas on the vaporization rate of the following reaction: SmCl 3 (l) = SmCl 3 (g) were analyzed. The vaporization rate of the process was found to be independent of then total gas flow rate and highly dependent on the temperature. E ap calculation led to a value of 240 ± 10 kJ.mol -1 . A comparison between this value and that of the molar enthalpy of vaporization allow to the conclusion that the reaction occur in conditions near to equilibrium. The SmCl 3 identity was determined by X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS). (author)

OXIDATIVE DEHYDROGENATION OF PROPANE BY RARE EARTH PHOSPHATES SUPPORTED ON AL-PILC

Directory of Open Access Journals (Sweden)

Carolina De Los Santos

2012-12-01

Full Text Available Catalytic activity in propane oxidative dehydrogenation of rare earth phosphates LnPO4 (where Ln = La, Ce, Pr, Nd, Sm and of the same supported by an aluminum pillared clay, of high specific surface area, is presented. The solids were characterized by TGA, XRD, nitrogen adsorption and immediate analysis after reaction in order to determine eventual carbon formation. Catalytic assays were performed at temperatures in the range 400oC-600oC, the reaction mixture was C3H8/O2/Ar = 10/10/80. All the catalysts were active. The reaction products were H2, CO, CO2, CH4, C2H4 and C3H6 and there were no organic oxygenated compounds detected. Although all the investigated systems were active, the Al-PILC supported catalysts presented a higher activity than the bulk materials. In this context, the samarium supported catalyst showed a propene yield increase from 4% to 10% compared with bulk samarium phosphate at 600°C. This effect was attributed to the increase in the specific surface area.

Oklo natural reactor. Study of uranium and rare earths migration on a core drilled through a reaction zone. Application to determination of the date of the nuclear reaction by measurement of fission products

International Nuclear Information System (INIS)

Ruffenach, J.C.

1977-01-01

Isotopic and chemical analysis of uranium and five rare earths: neodymium, samarium, europium, gadolinium and dysprosium were effected on fourteen samples taken in the same core drilled through a reaction zone of the Oklo uranium deposit. This study points out the general stability of uranium and fission rare earths; spatial distributions of these elements are quite analogous. Migrations have affected about 5% only of fission neodymium in the core of the reaction zone; corresponding values for samarium and gadolinium are slightly higher. These migration phenomena have carried rare earths to no more than 80 cm out of the core. By study of the europium it is shown that nuclear reactions have stayed in the ground since the time of reactions. On the other hand it is shown by analysis of the dysprosium that rare earths have not undergone an important movement. This study allow also the datation of nuclear reactions from the measurement of the quantity of fission neodymium produced. A value of 1.98x10 9 years is obtained slightly higher than the value obtained by geochronology [fr

Physical and structural properties of Sm3+ ions doped heavy metal oxide containing lanthanum-boro-telluirte glass

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-05-01

The structural studies of Tellurium oxide substituted by samarium oxide in lathanum-lead-boro-tellurite glass are successfully prepared with physical and optical parameters are determined. Due to the effect of increased number of non-bridging oxygen's in the glass samples few physical parameters are observed to be decreased. For the better structural analysis FTIR was carried out and transformation of BO3 → BO4 is observed. Most effective absorption coefficient OH- group was attained in the present work.

Effect of additives in the baking of electrolytic materials for SOFC; SOFC yo denkaishitsu zairyo no shoseiji ni okeru tenkabutsu no koka

Energy Technology Data Exchange (ETDEWEB)

Yoshida, H. [Kansai Electric Power Co. Inc., Osaka (Japan)

1998-09-10

A technique is discovered for improving on the baking properties of cerium oxide which is one of the solid electrolytic materials for SOFC (solid oxide fuel cell). Cerium oxide, samarium oxide, and gallium oxide are weighed, each to the specified element ratio. The element ratio of cerium is fixed at 0.8 against the other elements except oxygen, and the element ratios of samarium or gallium are caused to change. Specimens containing gallium are designated as CSGa, those not containing as SDC. SDC baked at 1600degC and CSGa (1%) baked at 1450degC are similar to each other in terms of average grain diameter. Specimens with gallium added thereto can be baked at temperatures that are lower than these by approximately 150degC. The conductivity of CSGa (0.2%) baked at 1500degC is higher than that of SDC baked at the same temperature, and is similar to that of SDC baked at 1600degC. Baking is enhanced by the addition of 0.2% gallium. In the domain where more than 1% of gallium is in presence, conductivity lowers with an increase in the amount of gallium added. The conductivity of CSGa (1%) baked at 1450degC is similar to that of SDC baked at 1600degC. 4 figs., 1 tab.

Developing Cost-Effective Dense Continuous SDC Barrier Layers for SOFCs

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Hoang Viet P.; Hardy, John S.; Coyle, Christopher A.; LU, Zigui; Stevenson, Jeffry W.

2017-12-04

Significantly improved performance during electrochemical testing of a cell with a dense continuous pulsed laser deposited (PLD) samarium doped ceria (SDC) layer spurred investigations into the fabrication of dense continuous SDC barrier layers by means of cost-effective deposition using screen printing which is amenable to industrial production of SOFCs. Many approaches to improve the SDC density have been explored including the use of powder with reduced particle sizes, inks with increased solids loading, and doping with sintering aids (1). In terms of sintering aids, dopants like Mo or binary systems of Mo+Cu or Fe+Co greatly enhance SDC sinterability. In fact, adding dopants to a screen printed, prefired, porous SDC layer made it possible to achieve a dense continuous barrier layer atop the YSZ electrolyte without sintering above 1200°C. Although the objective of fabricating a dense continuous layer was achieved, additional studies have been initiated to improve the cell performance. Underlying issues with constrained sintering and dopant-enhanced ceria-zirconia solid solubility are also addressed in this paper.

Extraction of lanthanide elements and bismuth in molten lithium chloride-liquid bismuth-lithium alloy system

International Nuclear Information System (INIS)

Harada, Makoto; Adachi, Motonari; Kai, Yuichi; Koike, Kenichi

1987-01-01

The equilibrium distributions of neodymium and samarium between molten LiCl and liquid Bi-Li alloy were measured in a wide range of Li-mole fraction in the alloy phase, X Li . These lanthanide elements were extracted through redox reactions. In high X Li range, X Li > 0.03, the distributions of neodymium and bismuth in the salt phase increased markedly. The anomalous increase is attributed to the formation of the compound comprized of Nd, Li, Bi and oxygen in the salt phase. The reaction processes in samarium and neodymium were very fast and the extraction rates are controlled by the diffusion processes of the solutes and metallic lithium. (author)

Reductive trapping of [(OC){sub 5}W-W(CO){sub 5}]{sup 2-} in a mixed-valent Sm{sup II/III} calix[4]pyrrolide sandwich

Energy Technology Data Exchange (ETDEWEB)

Deacon, Glen B.; Guo, Zhifang [School of Chemistry, Monash University, VIC (Australia); Junk, Peter C.; Wang, Jun [College of Science and Engineering, James Cook University, Townsville, QLD (Australia)

2017-07-10

Reduction of tungsten hexacarbonyl by the divalent samarium(II) complex [Sm{sub 2}(N{sub 4}Et{sub 8})(thf){sub 4}] ((N{sub 4}Et{sub 8}){sup 4-}=meso-octaethylcalix[4]pyrrolide) in toluene at ambient temperature gave the remarkable heteronuclear mixed-valent samarium(II/III)/tungsten complex [{(thf)_2Sm"I"I(N_4Et_8)Sm"I"I"I(thf)}{sub 2}{(μ-OC)_2W_2(CO)_8}], which features the trapping of a rare [W{sub 2}(CO){sub 10}]{sup 2-} anion with an unsupported W-W bond. (copyright 2017 Wiley-VCH Verlag GmbH and Co. KGaA, Weinheim)

Contamination of YBCO bulk superconductors by samarium and ytterbium

Czech Academy of Sciences Publication Activity Database

Volochová, D.; Jurek, Karel; Radušovská, M.; Piovarči, S.; Antal, V.; Kováč, J.; Jirsa, Miloš; Diko, P.

2014-01-01

Roč. 496, JAN (2014), s. 14-17 ISSN 0921-4534 Institutional support: RVO:68378271 Keywords : YBCO bulk superconductors * critical temperature * critical current density * peak effect Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.942, year: 2014

Reactivity effects of fission product decay in PWRs

International Nuclear Information System (INIS)

Aragones, J.M.; Ahnert, C.

1988-01-01

The purpose of the work reported in this paper is to analyze the effects of fission product chains with radioactive decay on the reactivity in pressurized water reactor (PWR) cores, calculating their accumulation and absorption rates along fuel burnup at continuous operation and after shutdown periods extending from 1 day to a few months. The authors PWR version of the WIMS-D4 code is first used to obtain the individual number densities, absorption rates, and averaged cross sections for every nuclide of the fission product chains with significant decay rates, as a function of fuel burnup at continuous irradiation. Next, by an auxiliary ad hoc code, these data, have been processed together with the required one for fissile nuclides and boron, also taken from WIMS at each burnup step, to calculate the average or effective values relevant for the analysis and the decay and change in overall absorption after several shutdown times. (1) The reactivity effect of fission product decay changes significantly with the shutdown time. The maximum absorption increase by decay is reached in ∼ 10 days' shutdown. (2) The dependence with fuel type, enrichment, and burnup is slight, but the change with previous power density is nearly linear, which might be significant after coast-down in previous cycles. (3) For long shutdown periods, the overall reactivity effect of decay in the three fission product chains considered is much less than if only the samarium peak due to 149 Nd is considered

Sm cluster superlattice on graphene/Ir(111)

Science.gov (United States)

Mousadakos, Dimitris; Pivetta, Marina; Brune, Harald; Rusponi, Stefano

2017-12-01

We report on the first example of a self-assembled rare earth cluster superlattice. As a template, we use the moiré pattern formed by graphene on Ir(111); its lattice constant of 2.52 nm defines the interparticle distance. The samarium cluster superlattice forms for substrate temperatures during deposition ranging from 80 to 110 K, and it is stable upon annealing to 140 K. By varying the samarium coverage, the mean cluster size can be increased up to 50 atoms, without affecting the long-range order. The spatial order and the width of the cluster size distribution match the best examples of metal cluster superlattices grown by atomic beam epitaxy on template surfaces.

Effects of the atomic environment on the electron binding energies in samarium

Czech Academy of Sciences Publication Activity Database

Inoyatov, A. K.; Kovalík, Alojz; Filosofov, D. V.; Ryšavý, Miloš; Vénos, Drahoslav; Yushkevich, Y. V.; Perevoshchikov, L. L.; Zhdanov, V. S.

2016-01-01

Roč. 207, FEB (2016), s. 38-49 ISSN 0368-2048 R&D Projects: GA ČR(CZ) GAP203/12/1896; GA MŠk LG14004 Institutional support: RVO:61389005 Keywords : Sm-149 * atomic environment * electron ginding energy * intermediate-valence state * chemical shift * natural atomic level width Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 1.661, year: 2016

Measurement of solubility of plutonium trifluoride and rare-earth fluorides in molten LiF-BeF2-ZrF4

International Nuclear Information System (INIS)

Naumov, V.S.; Bychkov, A.V.; Kormilitsyn, M.V.

1996-12-01

Data on behavior of plutonium fluoride and fission products (FP) dissolved in fuel composition are needed to calculate the duration of an operating cycle of the ADTT facility (Accelerator-Driver Transmutation Technologies) and to determine the effect of their equilibrium concentrations on nuclear-physical characteristics of reactor operation. The data on the FP fluoride solubility in the molten salts are of great important for some industrial processes (electrolytical metal deposition, development of physical-chemical mean for processes of chemical technology, etc.) As noted above, some information on this question is given in monography and articles. Data concerning fluoride salts are given in reports. However, it was impossible to make the substantial analysis of mutual solubility of fluoride melts. The primary investigation of CeF 3 and neodymium, samarium and lanthanum fluorides showed that the solubility of the melt LiF-BeF 2 and LiF-BeF 2 -ThF 4 was a linear function of reverse temperature and increases from lanthanum to samarium in the row of rare-earth elements. Disagreement in estimation of plutonium trifluoride solubility and incomplete data on the solubility of rare-earth elements prompted this study

Neutron activation analysis of geological material

International Nuclear Information System (INIS)

Greef, G.J.

1977-05-01

In neutron activation analysis the precision and accuracy of results are often misleading, since only the statistical errors which accompany the measuring of radioactivity are taken into consideration. Several other factors can, however, also influence precision and accuracy. It was found that a geological sample was contaminated with the construction material of the mill in which it had been pulverised. Several geometrical differences which could possibly play a role were also investigated. Impurities in the irradiation containers affect the determination of some elements in the samples; the contamination materials in quarts irradiation tubes were determined. The flux gradients which may effect the relative activities of the samples and standards were measured. Suitable standards are necessary to ensure accurate analyses of geological material. Available natural standards were critically evaluated and several methods were investigated by which synthetic standards may be prepared. In order to accurately determine gallium, lanthanum and samarium by means of neutron activation analysis, sodium first had to be removed. After irradiation the sample was dissolved in a mixture of acids and the soidium absorbed from the solution on a hydrated antimony pentoxide column. Gallium, lanthanum and samarium activities were measured by means of precision gamma-spectrometry

Magnetic and magnetoelastic properties of epitaxial SmFe{sub 2} thin film

Energy Technology Data Exchange (ETDEWEB)

Fuente, C de la; Arnaudas, J I; Ciria, M; Del Moral, A [Departamento de Magnetismo de Solidos and Departamento de Fisica de la Materia Condensada, Instituto de Ciencia de los Materiales de Aragon and Universidad de Zaragoza, 50071, Zaragoza (Spain); Dufour, C; Dumesnil, K, E-mail: cesar@unizar.e [Laboratoire de Metallurgie Physique et de Science des Materiaux, Universite Henry Poincare, Nancy 1, BP 239, 54506 (France)

2010-02-03

We report on magnetic and magnetoelastic measurements for a 5000 A (110) SmFe{sub 2} thin film, which was successfully analyzed by means of a point charge model for describing the effect of the epitaxial growth in this kind of system. Some of the main conclusions of the Moessbauer and magnetoelastic results and the new magnetization results up to 5 T allow us to get a full description of the crystal electric field, exchange, and magnetoelastic behavior in this compound. So, new single-ion parameters are obtained for the crystal field interaction of samarium ions, A{sub 4}(r{sup 4}) = +755 K/ion and A{sub 6}(r{sup 6}) = -180 K/ion, and new single-ion magnetoelastic coupling B{sup gamma}{sup ,2}approx =-200 MPa and B{sup epsilon}{sup ,2}approx =800 MPa, which represent the tetragonal and the in-plane shear deformations, respectively. Moreover, the new thermal behavior of the samarium magnetic moment, the exchange coupling parameter, and the magnetocrystalline anisotropy of the iron sublattice are obtained too. From these, the softening of the spin reorientation transition with respect to the bulk case could be accounted for.

Part I. An investigation into the mechanism of the samarium (II)-promoted Barbier reaction: Sequential radical cyclization/organometallic addition. Part II. Conjugate addition reactions of organosamarium reagents by in situ transmetalation to cuprates. Part III. Approximate absolute rate constants for the reaction of tributyltin radicals with aryl and vinyl halides. Part IV. An investigation into the synthetic utility of tri-n-butylgermanium hydride

Energy Technology Data Exchange (ETDEWEB)

Totleben, M.J.

1992-01-01

An investigation of the mechanism of the samarium diiodide mediated Barbier reaction was conducted. Through a series of alkyl halide-carbonyl coupling and deuterium labelling experiments, evidence supportive of an organometallic addition mechanism was collected. Further probing led to an expansion of the utility of SmI[sub 2] in synthesis. The author has shown that radical cyclization of aryl and alkyl radicals to olefins, followed by reduction to primary and secondary organosamarium species is feasible. Organosamarium (III) reagents, produced by the reduction of alkyl and select aryl halides with 2 equiv of SmI[sub 2] in THF/HMPA, were treated with copper (I) salts and complexes to effect in situ transmetalation to cuprates. This allowed the 1,4-addition to [alpha],[beta]-unsaturated ketones. This new methodology allows for the sequential formation of carbon-carbon bonds through a combination of free radical and cuprate chemistry. Absolute rate constants for the abstraction of bromine atoms (k[sub Br]) by tri-n-butyltin radicals from a series of vinyl and aryl bromides have been determined. Atom abstraction was modestly enhanced by proximity of the halogen to a substituent in the following order: para < meta < ortho. Tri-n-butyl germanium hydride is known to be a poorer hydrogen atom donor than its tin analog. This feature makes it attractive for use in slow radical cyclizations where tin hydride would provide mainly for reduction. A brief study was executed to improve on the utility of the reagent as current conditions do not yield desired products in high amounts. Initial investigations examined the effect of initiator on reduction by germanium hydride, and subsequent experiments probed solvent effects. t-Butyl alcohol was determined to be superior to benzene or acetonitrile, giving consistently higher yields of reduction products.

Effect of heavy atoms on the thermal stability of α-amylase from Aspergillus oryzae.

Directory of Open Access Journals (Sweden)

Michihiro Sugahara

Full Text Available Currently, there are no versatile and established methods for improving stability of proteins. In an entirely different approach from conventional techniques such as mutagenesis, we attempted to enhance enzyme stability of α-amylase from Aspergillus oryzae using a heavy-atom derivatization technique. We evaluated changes in stability using differential scanning calorimetry (DSC. Candidate heavy atoms were identified using the Heavy-Atom Database System HATODAS, a Web-based tool designed to assist in heavy-atom derivatization of proteins for X-ray crystallography. The denaturation temperature of α-amylase derivatized with gadolinium (Gd or samarium (Sm ions increased by 6.2 or 5.7°C, respectively, compared to that of the native protein (60.6°C. The binding of six Gd ions was confirmed by X-ray crystallography of the enzyme at 1.5 Å resolution. DSC and dynamic light-scattering data revealed a correlation between stability and the aggregation state upon addition of Gd ions. These results show that HATODAS search is an effective tool for selecting heavy atoms for stabilization of this protein.

Emission properties of Sm(III) complex having ten-coordination structure

International Nuclear Information System (INIS)

Hasegawa, Yasuchika; Tsuruoka, Shin-ichi; Yoshida, Takahiko; Kawai, Hideki; Kawai, Tsuyoshi

2008-01-01

Sammarium(III) complex having ten-coordination structure, bis-(1,10-phenanthroline)tris-(hexafluoroacetylacetonato)samarium(III) (Sm(hfa) 3 (phen) 2 ) was prepared by chelation of tris-(hexafluoroacetylacetonato) samarium(III) (Sm(hfa) 3 (H 2 O) 2 ) with 1,10-phenantroline (phen). The characteristic ten-coordination structure of Sm(hfa) 3 (phen) 2 was determined by 1 H NMR and elemental analyses. Strong deep-red emission (λ max =643 nm) and narrow emission band (FWHM=5 nm) of Sm(hfa) 3 (phen) 2 originated from electronic allowed transition from characteristics ten coordinate structure. The emission quantum yields Sm(hfa) 3 (phen) 2 excited at absorption bands of ligands and Sm(III) ion were found to be 0.36 and 1.4%, respectively

Half-life of samarium-147

CERN Document Server

Kinoshita, N; Nakanishi, T

2003-01-01

The alpha-decay half-life of sup 1 sup 4 sup 7 Sm has been reevaluated. Known amounts of natural Sm and an alpha-emitter standard ( sup 2 sup 1 sup 0 Po, sup 2 sup 3 sup 8 U, or sup 2 sup 4 sup 1 Am) were mixed well to prepare thin sources for the simultaneous counting of sup 1 sup 4 sup 7 Sm and the alpha-emitter standard by means of an alpha-spectrometer using a silicon surface barrier detector. The alpha-disintegration rate of known amounts of sup 1 sup 4 sup 7 Sm was determined by reference to the alpha activity of the standard. The source preparation and counting were repeated to establish the reproducibility of the present half-life determination, and supplementary alpha spectrometry was carried out by a liquid-scintillation spectrometer. The arithmetic mean of the experimental half-life values was obtained to be (1.17 +- 0.02) x 10 sup 1 sup 1 y. This value is about 10% longer than the currently adopted value, (1.06 +- 0.02) x 10 sup 1 sup 1 y, and the possible factors for this difference are discussed...

Isotopic studies on oxidative methane coupling over samarium oxide

International Nuclear Information System (INIS)

Otsuka, Kiyoshi; Inaida, Masakatsu; Wada, Yuji; Komatsu, Takayuki; Morikawa, Akira

1989-01-01

The evident kinetic isotope effect was observed for the formations of ethylene and ethane through the oxidative coupling of methane on Sm 2 O 3 , when CH 4 and CD 4 were used as the reactants. Ethanes formed in the reaction of a mixture of CH 4 , CD 4 , and O 2 were C 2 H 6 , C 2 H 3 D 3 , and C 2 D 6 as major products. These results indicate that the rate-determining step of the reaction is abstraction of hydrogen from methane and that ethane is formed through the coupling of methyl intermediate. (author)

Samarium Hexaboride: The First True 3D Topological Insulator?

Science.gov (United States)

Wolgast, Steven G.

The recent theoretical prediction of a topologically protected surface state in the mixed-valent insulator SmB6 has motivated a series of charge transport studies, which are presented here. It is first studied using a specialized configuration designed to distinguish bulk-dominated conduction from surface-dominated conduction. As the material is cooled below 4 K, it exhibits a crossover from thermally activated bulk transport to metallic surface conduction with a fully insulating bulk. The robustness and magnitude of the surface conductivity, as is manifest in the literature of SmB6, is strong evidence for the topological insulator (TI) metallic surface states predicted for this material. This resolves a decades-old puzzle surrounding the low-temperature behavior of SmB6. Next, the magnetotransport properties of the surface are investigated using a Corbino disk geometry, which can directly measure the conductivity of individual surfaces. Both (011) and (001) crystal surfaces show a strong negative magnetoresistance at all magnetic field angles, due primarily to changes in the carrier density. The low mobility value accounts for the failure so far to observe Shubnikov-de Haas oscillations below 95 T. Small variations in the mobility and temperature dependence suggest a suppression of Kondo scattering from native oxide-layer magnetic moments. At low fields, a dynamical field-sweep-rate-dependent hysteretic behavior is observed. It persists at the slowest sweep rates, and cannot be explained by quantum interference corrections; it is likely due to extrinsic effects such as the magnetocaloric effect or glassy ordering of the native oxide moments. Pulsed magnetic field measurements up to 60 T at temperatures throughout the crossover regime clearly distinguish the surface magnetoresistance from the bulk magnetoresistance. The bulk magnetoresistance is due to a reduction in the bulk gap with increasing magnetic field. Finally, small subsurface cracks formed in SmB6 via

Radiolesão vascular como efeito deletério da braquiterapia intra-arterial com dose elevada de Samário-153 em coelhos hipercolesterolêmicos Vascular radiolesion as a deleterious effect of high-dose-rate intraarterial brachytherapy with Samarium-153 in hypercholesterolemic rabbits

Directory of Open Access Journals (Sweden)

Dalton Bertolim Précoma

2006-10-01

Full Text Available OBJETIVO: Este estudo tem por objetivo avaliar as alterações vasculares morfológicas e morfométricas induzidas pela braquiterapia com Samário-153 (153 Sm em coelhos hipercolesterolêmicos, com doses elevadas. MÉTODOS: Foram analisados 43 coelhos hipercolesterolêmicos, brancos, da raça New Zealand, e o total de 86 artérias ilíacas submetidas a lesão por balão de angioplastia. Divididos em três grupos: dois (GI irradiados com as doses de 15Gy (n=14 e 60Gy (n=36 e um grupo controle (n=36. Foram realizadas avaliação histológica morfométrica e análise histológica qualitativa para análise tecidual. RESULTADOS: Foram observadas uma redução significativa da neoproliferação intimal (NPI no GI 15 Gy (pOBJECTIVE: This study was designed to evaluate vascular morphological and morphometric changes induced by brachytherapy with samarium-153 (Sm-153 at high doses in hypercholesterolemic rabbits. METHODS: Forty-three New Zealand White hypercholesterolemic rabbits were analyzed, and the total of 86 iliac arteries underwent balloon angioplasty injury. The rabbits were divided into three different groups: two irradiation groups (IG assigned to 15 Gy (n=14 and 60 Gy (n=36 irradiation doses, respectively, and a control group (n = 36. Histomorphometric and qualitative histological analyses were performed for tissue evaluation. RESULTS: Significant reductions were found in neointimal proliferation (NIP (p< 0.0001, media area (MA (p<0.0001 and percent stenosis (p<0.0001 in the 15-Gy IG, compared to the other groups. The 60-Gy IG had the higher rate of NIP, increase in media and vessel areas (VA and percent stenosis. The 60-Gy IG also showed the greatest number of xanthomatous cells (60-Gy IG: 86.11% and 15-Gy IG: 14.29%, p<0.0001 and the highest amount of hyaline amorphous tissue (60-Gy IG:58.33% and 15-Gy IG:0%, p=0.0001 and vascular proliferation (60-Gy IG:30.56% and 15-Gy IG:0%, p=0.0221. No statistically significant differences were found

Preparation of plutonium waste forms with ICPP calcined high-level waste

Energy Technology Data Exchange (ETDEWEB)

Staples, B.A.; Knecht, D.A. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States); O`Holleran, T.P. [Argonne National Lab.-West, Idaho Falls, ID (United States)] [and others

1997-05-01

Glass and glass-ceramic forms developed for the immobilization of calcined high-level wastes generated by Idaho Chemical Processing Plant (ICPP) fuel reprocessing activities have been investigated for ability to immobilize plutonium and to simultaneously incorporate calcined waste as an anti-proliferation barrier. Within the forms investigated, crystallization of host phases result in an increased loading of plutonium as well as its incorporation into potentially more durable phases than the glass. The host phases were initially formed and characterized with cerium (Ce{sup +4}) as a surrogate for plutonium (Pu{sup +4}) and samarium as a neutron absorber for criticality control. Verification of the surrogate testing results were then performed replacing cerium with plutonium. All testing was performed with surrogate calcined high-level waste. The results of these tests indicated that a potentially useful host phase, based on zirconia, can be formed either by devitrification or solid state reaction in the glass studied. This phase incorporates plutonium as well as samarium and the calcined waste becomes part of the matrix. Its ease of formation makes it potentially useful in excess plutonium dispositioning. Other durable host phases for plutonium and samarium, including zirconolite and zircon have been formed from zirconia or alumina calcine through cold press-sintering techniques and hot isostatic pressing. Host phase formation experiments conducted through vitrification or by cold press-sintering techniques are described and the results discussed. Recommendations are given for future work that extends the results of this study.

Preparation of plutonium waste forms with ICPP calcined high-level waste

International Nuclear Information System (INIS)

Staples, B.A.; Knecht, D.A.; O'Holleran, T.P.

1997-05-01

Glass and glass-ceramic forms developed for the immobilization of calcined high-level wastes generated by Idaho Chemical Processing Plant (ICPP) fuel reprocessing activities have been investigated for ability to immobilize plutonium and to simultaneously incorporate calcined waste as an anti-proliferation barrier. Within the forms investigated, crystallization of host phases result in an increased loading of plutonium as well as its incorporation into potentially more durable phases than the glass. The host phases were initially formed and characterized with cerium (Ce +4 ) as a surrogate for plutonium (Pu +4 ) and samarium as a neutron absorber for criticality control. Verification of the surrogate testing results were then performed replacing cerium with plutonium. All testing was performed with surrogate calcined high-level waste. The results of these tests indicated that a potentially useful host phase, based on zirconia, can be formed either by devitrification or solid state reaction in the glass studied. This phase incorporates plutonium as well as samarium and the calcined waste becomes part of the matrix. Its ease of formation makes it potentially useful in excess plutonium dispositioning. Other durable host phases for plutonium and samarium, including zirconolite and zircon have been formed from zirconia or alumina calcine through cold press-sintering techniques and hot isostatic pressing. Host phase formation experiments conducted through vitrification or by cold press-sintering techniques are described and the results discussed. Recommendations are given for future work that extends the results of this study

Preparation and dosimetry of radiotherapeutic particles for arthropaties; Preparacion y dosimetria de particulas radioterapeuticas para artropatias

Energy Technology Data Exchange (ETDEWEB)

Gonzalez Z, M A [Departamento de Medicina Nuclear, Instituto Nacional de Pediatria (Mexico); Ferro F, G [Departamento de Materiales Radiactivos, Instituto nacional de Investigaciones Nucleares, Salazar, Estado de Mexico C.P. 52045 (Mexico); Rivera M, T; Azorin N, J [Departamento de Fisica, UAM Iztapalapa, Mexico D.F. (Mexico)

1999-07-01

It was developed a new formulation of macro aggregates of Samarium 153 ({sup 153} Sm-MH) for the arthropaties treatment. The radio pharmaceutic was prepared by reaction of Samarium 153 chloride (SmCl{sub 3}) in aqueous environment with sodium boron hydride in NaOH 0.5 N. The microscopic analysis shown that the particles have an average size of 4% m (range 1-14 {mu} m). The velocity of sedimentation was 0.008 cm/min with high stability in vitro in human serum. The biological studies in healthy rabbits, shown that the complex is retained inside the articulation still eight days after of the administration of the radiopharmaceutical. Likewise, it is presented the data of absorbed dose in the different target organs, which was determined by thermoluminescent dosimetry (TLD) through the use of a REMCAL phantom (radiation equivalent manikin calibration). (Author)

Preparation and dosimetry of radiotherapeutic particles for arthropaties

International Nuclear Information System (INIS)

Gonzalez Z, M.A.; Ferro F, G.; Rivera M, T.; Azorin N, J.

1999-01-01

It was developed a new formulation of macro aggregates of Samarium 153 ( 153 Sm-MH) for the arthropaties treatment. The radio pharmaceutic was prepared by reaction of Samarium 153 chloride (SmCl 3 ) in aqueous environment with sodium boron hydride in NaOH 0.5 N. The microscopic analysis shown that the particles have an average size of 4% m (range 1-14 μ m). The velocity of sedimentation was 0.008 cm/min with high stability in vitro in human serum. The biological studies in healthy rabbits, shown that the complex is retained inside the articulation still eight days after of the administration of the radiopharmaceutical. Likewise, it is presented the data of absorbed dose in the different target organs, which was determined by thermoluminescent dosimetry (TLD) through the use of a REMCAL phantom (radiation equivalent manikin calibration). (Author)

Simplified syntheses of the water-soluble chiral shift reagents Sm-(R)-pdta and Sm-(S)-pdta

Czech Academy of Sciences Publication Activity Database

Hrubá, L.; Buděšínský, Miloš; Pícha, Jan; Jiráček, Jiří; Vaněk, Václav

2013-01-01

Roč. 54, č. 47 (2013), s. 6296-6297 ISSN 0040-4039 Institutional support: RVO:61388963 Keywords : NMR * chiral shift reagents * Sm-pdta * PDTA * samarium * 1,2-diaminopropane Subject RIV: CC - Organic Chemistry Impact factor: 2.391, year: 2013

Effect of 153Sm-EDTMP on survival time in patients with nasopharyngeal carcinoma and multiple bone metastases

International Nuclear Information System (INIS)

Fan Wei; Zheng Zongyuan; Xu Guangpu

2004-01-01

Objective: To evaluate the effect on survival of Samarium-153-ethylene diamine tetramethylene phosphonate (153Sm-EDTMP) in patients with nasopharyngeal carcinoma (NPC) and multiple bone metastases. Methods: From 1993 to 1999, 160 patients (127 men, 33 women; median age 35 years) presented with NPC and multiple bone metastases. Of these, 40 patients had undergone chemotherapy, and 72 palliative radiotherapy. Patients were randomly divided into four groups: Group 1 (N = 20) received analgesics (control); Groups 2, 3 and 4 (N = 80, 40, and 20, respectively) received one, two or three courses, respectively, of 153Sm-EDTMP (77.7 MBq/kg/course; course interval, 4 wk). Results: Eight patients died of non-cancer-related causes, and 24 were lost to follow-up. The median survival time for Group 1 (7.8 months) was significantly less (p < 0.05) than that of Groups 2, 3 and 4 (11.6, 13.4 and 12.8 months, respectively). Patients given 153Sm-EDTMP who had had revious external radiation survived longer (p < 0.05) than those in the other treatment groups. Conclusions: Internal radiotherapy with 153Sm-EDTMP can extend survival time in patients with nasopharyngeal carcinoma and multiple bone metastases; when combined with external radiotherapy in appropriate patients, its effect on survival time is enhanced.. (authors)

The effect of diluents on the extraction of Sm(III using N,N,N’,N’-tetrabutylmalonamide

Directory of Open Access Journals (Sweden)

SUN SI-XIU

2004-09-01

Full Text Available A study has been made of the extraction of samarium(III from nitrate solutions using N,N,N’,N’-tetrabutylmalonamide (TBMA in a series of diluents. The dependence of the extraction distribution on the concentrations of aqueous nitric acid, lithium nitrate and organic TBMA was investigated. The experimental results showed that the extraction efficiency of TMBA in different diluents for Sm(III increases in the order: chloroform, carbon tetrachloride, benzene, xylene, toluene, cyclohexane, n-hexane, n-octane. The stoichiometry of the extracted species conform to Sm(NO33.3TBMA in all the employed diluents. The interaction between extractant or extracted species and diluent is discussed and a quantitative expression relating the extraction constant and the parameters of the diluent has been established.

Radiolabelling of potential colonic delivery systems by neutron activation. An evaluation based on physiochemical properties of excipients and formulations

International Nuclear Information System (INIS)

Ahrabi, Sayeh

1999-01-01

The effects of neutron irradiation on the physicochemical properties of some potential release-controlling excipients for oral delivery to colon (based on microbially degradable polysaccharide or a combination of pH- and time-dependent mechanisms) were initially investigated. The aim was to choose the most irradiation-resistant ones for the development of a colonic delivery system to be radiolabelled by the neutron activation procedure. However, no correlation between the extent of irradiation-induced changes of the release-controlling polymers and the in vitro properties of the final formulation was observed. Incorporation of samarium oxide (Sm 2 O 3 ) resulted in retardation of the drug release through the diffusion layer. The influence of neutron activation factors on the properties of some suppository combinations was also studied. The effect of the admixture of Sm 2 O 3 on the dissolution and disintegration of the suppositories was more profound than the effect of neutron irradiation. In hydrophilic suppositories, the effect of Sm 2 O 3 was dependent on the type, amount and the physicochemical characteristics of the incorporated drug. In lipophilic suppositories, the release-controlling effect of Sm 2 O 3 was hypothesised to be due to its insoluble micronised particles blocking the drug diffusion layer. The neutron activation procedure could be utilised for radiolabelling potential oral and rectal colonic drug delivery systems. However, to avoid alteration in the crucial in vitro characteristics of the formulations, the amount, the particle size and the aggregated particle characteristics of the lanthanide salt (e.g. Sm 2 O 3 or samarium stearate) together with the neutron irradiation dose should be controlled precisely for each dosage system. For the systems investigated in this work the release-controlling mechanism of the dosage form seems to be a key parameter to predict the extent of the influence of neutron activation factors on the in vitro properties

A NOVEL SAMARIUM COMPLEX WITH INTERESTING ...

African Journals Online (AJOL)

2017 Chemical Society of Ethiopia and The Authors ... 1Institute of Applied Chemistry, School of Chemistry and Chemical Engineering, Jinggangshan ... 3State Key Laboratory of Structural Chemistry, Fujian Institute of Research ... INTRODUCTION ..... Fenamate cocrystals with 4,4'-bipyridine: structural and thermodynamic ...

Pramana – Journal of Physics | Indian Academy of Sciences

Indian Academy of Sciences (India)

... and theoretical aspects of fundamental symmetry violations in atoms .... The current status of and achievements in targets are provided and validation experiments are ... of samarium by spectrally resolved laser-induced fluorescence technique .... Surface roughness-aided hard X-ray emission from carbon nanotubes.

Analysis of bioactive glasses obtained by sol-gel processing for radioactive implants

Directory of Open Access Journals (Sweden)

Roberto Wanderley dos Santos

2003-01-01

Full Text Available This paper presents the chemical and physical characterizations of SiO2 and SiO2-CaO bioactive glasses incorporated with samarium atoms, produced by sol-gel synthesis. The objective is to provide biocompatible and biodegradable radioactive seeds as an alternative to be used in Brachytherapy for the treatment of prostate cancer. The glasses were produced and analyzed by X-ray fluorescence spectroscopy (XRF, energy dispersive X-ray spectroscopy (EDS, scanning electron microscopy (SEM, He picnometry and nitrogen adsorption analysis. A theoretical evaluation of the specific activity of the samples upon neutron activation is proposed. The XRF and EDS results demonstrate the incorporation of samarium atoms in the glass matrix. The experimental data coupled with the theoretical studies in neutron activation suggest that it is possible to obtain radioactive seeds with activities equivalent to 125I seeds used in brachytherapy prostatic.

Pain therapy with Samario 153-EDTM in prostate cancer. Pilot experience in Paraguay

International Nuclear Information System (INIS)

Jara Yorg, Jorge

2001-07-01

To relieve the skeletal pain in metastasis disseminated in bones, numerous radiotracers have been used without achieving important clinical acceptance. The SAMARIUM 153 EDT (Etilendiaminetrametilen acid phosphonic) is a radiopharmaceutic that is chemically and biologically stable and preferably concentrates on the skeletal metastasis [es

Electric Field-Assisted Pressureless Sintering of Ceramic Protonic Conductors

DEFF Research Database (Denmark)

Muccillo, R.; Esposito, Vincenzo; Zanetti De Florio, Daniel

2017-01-01

Gadolinium, yttrium and samarium-doped barium cerate (BCGd, BCY and BCSm, respectively) polycrystalline green pellets were submitted to electric field-assisted pressureless sintering experiments isothermally in the temperature range 800-1200oC under 100-200 V cm-1 electric fields, limiting to 1-5...

A convenient method for the conversion of N-acyloxazolidinones to hydroxamic acids.

Science.gov (United States)

Sibi, Mukund P; Hasegawa, Hikaru; Ghorpade, Sandeep R

2002-10-03

Treatment of N-acyloxazolidinones with hydroxylamines using samarium triflate as a Lewis acid provides the corresponding hydroxamic acids in 50-98% yields at room temperature. The conversion proceeds with high degree of chemoselectivity and without racemization of chiral centers alpha- to the acyl group. [reaction: see text

Biological evaluation of 153Sm-ethylenediaminetetra methylene phosphonate (EDTMP)

International Nuclear Information System (INIS)

Ranganatha, D.K.; Lal, Ramji

1997-01-01

Samarium-153 EDTMP has been studied in rats to establish bone localisation in normal bone tissue and the uptake in the soft tissue. Biodistribution results were highly promising with >3% of the injected dose localizing in the femurs and 15 days. (author). 4 refs., 2 tabs

Electric Field-Assisted Pressureless Sintering of Ceramic Protonic Conductors

DEFF Research Database (Denmark)

Muccillo, R.; Esposito, Vincenzo; de Florio, D. Z.

2017-01-01

Gadolinium, yttrium and samarium-doped barium cerate pressed pellets were submitted to flash sintering experiments isothermally in the temperature range 800-1300oC under 200 V cm-1 electric field. The pellets were positioned inside a dilatometer furnace with Pt-Ir electrodes connected either to a...

Kinetic energy of ions produced with first-, second-, and multi-shot femtosecond laser ablation on a solid surface

International Nuclear Information System (INIS)

Kobayashi, Tohru; Kato, Toshiyuki; Kurata-Nishimura, Mizuki; Matsuo, Yukari; Kawai, Jun; Motobayashi, Tohru; Hayashizaki, Yoshihide

2007-01-01

We report that the kinetic energy of samarium (Sm) atom and Sm + ion produced by femtosecond laser ablation of solid samarium is strongly dependent on the number of ablation laser shots in the range from 1 to 10. By ablating the fresh surface (i.e. 1st shot), we find the kinetic energy of both Sm and Sm + ion to be the largest (24 and 250 eV, respectively). Almost 10 times larger kinetic energy of Sm + ion than that of Sm clearly indicates the contribution of Coulomb explosion in the acceleration process. From the second shot, kinetic energies of Sm and Sm + ion are lower than those of the first shot and almost constant (ca. 12 and 80 eV, respectively). This behaviour suggests the change in the nature of the solid surface after femtosecond laser ablation, which can be explained by the amorphization of ablated sample surface reported in recent studies

Spontaneous and stimulated emission in Sm3+-doped YAl3(BO3)4 single crystal

International Nuclear Information System (INIS)

Ryba-Romanowski, Witold; Lisiecki, Radosław; Beregi, Elena; Martín, I.R.

2015-01-01

Single crystals of YAl 3 (BO 3 ) 4 doped with trivalent samarium were grown by the top-seeded high temperature solution method and their absorption and emission spectra were investigated. Optical pumping into prominent absorption band around 405 nm feeds the 4 G 5/2 metastable level giving rise to intense visible luminescence distributed in several spectral lines with the most intense line around 600 nm characterized by a branching ratio of 0.42 and peak emission cross section of 0.25×10 −20 cm 2 . Optical amplification at 600 nm with a gain coefficient of 2.9 cm −1 was achieved during a pump-and-probe experiment. - Highlights: • YAB:Sm crystal grown by the top-seeded high temperature solution method. • Spectroscopic qualities relevant for visible laser operation. • YAB:Sm single crystal used in a pump-and-probe experiment. • Optical amplification properties of samarium doped YAl 3 (BO 3 ) 4

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

It is observed that. the dielectric permittivity () and loss tangent (tan ) are dependent on frequency,; the temperature of dielectric permittivity maximum shifts toward lower temperature side with the increase of samarium ion (Sm+3) concentration at the Pb sites, and; observed and calculated -values of XRD patterns show ...

Tuning the activity of Pt alloy electrocatalysts by means of the lanthanide contraction

DEFF Research Database (Denmark)

Escribano, Maria Escudero; Malacrida, Paolo; Hansen, Martin Hangaard

2016-01-01

is lanthanum, cerium, samarium, gadolinium, terbium, dysprosium, thulium, or calcium. The materials are among the most active polycrystalline Pt-based catalysts reported, presenting activity enhancement by a factor of 3 to 6 over Pt. The active phase consists of a Pt overlayer formed by acid leaching. The ORR...

Bis(phenolate)amine-supported lanthanide borohydride complexes for styrene and trans-1,4-isoprene (co-)polymerisations

NARCIS (Netherlands)

Bonnet, Fanny; Dyer, Hellen E.; El Kinani, Yassine; Dietz, Carin; Roussel, Pascal; Bria, Marc; Visseaux, Marc; Zinck, Philippe; Mountford, Philip

2015-01-01

New bis(phenolate)amine-supported neodymium borohydride complexes and their previously reported samarium analogues were tested as catalysts for the polymerisation of styrene and isoprene. Reaction of Na2O2NL (L = py, OMe, NMe2) with Nd(BH4)3(THF)3 afforded the borohydride complexes

Separation and purification of gadolinium and others rare earths, and yttrium

International Nuclear Information System (INIS)

Awwal, M.A.; Filgueiras, S.A.C.

1988-01-01

The experimental works in laboratories for developing a solvent extraction process with the purpose of gadolinium separation and purification, and secondarily samarium, europium, lanthanum and yttrium are described. Using as solvent di-2-ethylhexylphosphoric acid (DEHPA) a preliminary flow chart for separation for these elements are developed. (author)

Measurement of total angular momentum values of high-lying even ...

Indian Academy of Sciences (India)

Spectrally resolved laser-induced fluorescence technique was used to uniquely assign total angular momentum () values to high-lying even-parity energy levels of atomic samarium. Unique value assignment was done for seven energy levels in the energy region 34,800–36,200 cm-1 , recently observed and reported in ...

Study of 148-152Sm nuclei employing γ - derived from B(E2) values and level energies

International Nuclear Information System (INIS)

Sharma, Aparna; Varshney, A.K.; Singh, M.; Gupta, D.K.; Singh, Yuvraj; Gupta, K.K.; Bihari, Chhail; Varshney, Mani

2011-01-01

The study of samarium nuclei has been a challenging theoretical problem, since they lie in the range from near spherical to well deformed shapes. 148 Sm was believed to be basically spherical while 154 Sm is thought to be well deformed nucleus and 150-15 '2Sm are transitional nuclei

Specification and comparative calculation of enthalpies and Gibbs formation energies of anhydrous lanthanide nitrates

International Nuclear Information System (INIS)

Del' Pino, Kh.; Chukurov, P.M.; Drakin, S.I.

1980-01-01

Analyzed are the results of experimental depermination of formation enthalpies of waterless nitrates of lanthane cerium, praseodymium, neodymium and samarium. Using method of comparative calculation computed are enthalpies of formation of waterless lanthanide and yttrium nitrates. Calculated values of enthalpies and Gibbs energies of waterless lanthanide nitrate formation are tabulated

Perovskite catalysts for oxidative coupling

Science.gov (United States)

Campbell, Kenneth D.

1991-01-01

Perovskites of the structure A.sub.2 B.sub.2 C.sub.3 O.sub.10 are useful as catalysts for the oxidative coupling of lower alkane to heavier hydrocarbons. A is alkali metal; B is lanthanide or lanthanum, cerium, neodymium, samarium, praseodymium, gadolinium or dysprosium; and C is titanium.

Investigation of nozzle shape effect on Sm0.1Ce0.9O1.95 thin film prepared by electrostatic spray deposition

International Nuclear Information System (INIS)

Ksapabutr, Bussarin; Panapoy, Manop; Choncharoen, Kittikhun; Wongkasemjit, Sujitra; Traversa, Enrico

2008-01-01

Dense samarium doped ceria (SDC) thin films are deposited using electrostatic spray deposition (ESD) technique. The influences of nozzle shape on the distribution of liquid jet at the nozzle tip and the morphology of the deposited SDC films are elucidated. Geometries of three nozzles employed are flat, sawtooth and wedge tips. From the observation of jet formation, the nozzle in flat shape gives the highest distribution of emitted droplets. The deposited films are characterized using a combination of XRD, SEM and AFM techniques. XRD results reveal that the single-phase fluorite structure forms at a relatively low deposition temperature of 400 o C. The flat spray tip provides the most uniform and smooth thin films, and also presents the lowest agglomeration of particles on thin-film surface

Conductivity fluctuation in the high temperature superconductor with planar weight disparity Y0.5Sm0.5Ba2Cu3O7-δ

International Nuclear Information System (INIS)

Barrera, E.W.; Rojas Sarmiento, M.P.; Rincon, L.F.; Landinez Tellez, D.A.; Roa-Rojas, J.

2007-01-01

The synthesis of the Y 0.5 Sm 0.5 Ba 2 Cu 3 O 7-δ superconducting material by the standard solid state reaction is reported. DC resistivity measurements reveal the improvement of the critical temperature (T c ) when substitution of exact 50-50 mix of Yttrium and Samarium is performed. A bulk T c = 101 K was determined by the criterion of the maximum in the temperature derivative of electrical resistivity. Structure characterization by means the x-ray diffraction technique shows the crystalline appropriated distribution of Yttrium and Samarium to create substantial planar weight disparity (PWD) in alternating layers. This PWD increases T c in copper-oxide superconductors. In order to examine the effect of PWD on the pairing mechanism close to T c , conductivity fluctuation analysis was performed by the method of logarithmic temperature derivative of the conductivity excess. We found the occurrence of Gaussian and genuinely critical fluctuations. Our results are in agreement with reports on YBa 2 Cu 3 O 7-δ , but an enhancement of the Gaussian fluctuation regimes was experimentally detected as a result of the PWD. The correlations of the critical exponents with the dimensionality of the fluctuation system for each Gaussian regime were performed by using the Aslamazov-Larkin theory. The genuinely critical exponent is interpreted by the 3D-XY model as corresponding with the dynamical universality class of the E-model. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Report on thermic effects in the study of the control and propagation of nuclear reactions

International Nuclear Information System (INIS)

Naudet, R.

It is very likely that nuclear reactions in natural reactors are governed by temperature, chiefly as a result of the moderation rate when the water density is altered. Since reactors operate under high pressure, with supercritical water, high temperatures (at least 350 to 400 0 C in some instances) are required in order to stabilize the reactors. Some typical calculations are shown in order to illustrate the changes in the control temperature during irradiation. The speed and, therefore, the duration of reactions is determined by the need to maintain the necessary temperature required for criticality, with heat dissipation conditions taken into account. Apparent measured durations are compatible with heat dissipation by simple conduction. However, it is likely that convection currents exist, and that their effects are superimposed on those of simple conduction. Reaction propagation must also be taken into consideration since criticality cannot be realized simultaneously at every point. The presence of impurities such as gadolinium or samarium in the mineral ore allows reactions to propagate in initially subcritical increments, through progressive breakdown of the impurities by means of neutronic diffusion. However, it has been shown that this phenomenon is seriously affected by thermic effects. Typical calculations are presented. Results clearly depend on temperature distribution hypotheses; sufficient thermic coupling can totally inhibit reaction propagation. It is concluded that, if convection currents are present, propagation is favored inversely with respect to the currents, and therefore a priori downstream of the reactors. 6 figures

Three-photon laser spectroscopy of even-parity bound states of samarium atom

International Nuclear Information System (INIS)

Gomonaj, O.Yi.; Kudelich, O.Yi.

2002-01-01

The energy spectrum of highly-excited even-parity bound states of a Sm atom, lying in the energy range 34421.1 - 36031.8 cm -1 , is investigated using three-photon resonance-ionization spectroscopy. The energies and total momenta of 48 levels are determined. Eight new levels not observed before are discovered. Thirteen intense two-photon transitions, which can be used in the schemes of Sm atom effective photoionization, are observed

Interstitial pressure dependence of the thermal conductivity of some rare earth oxide powders

International Nuclear Information System (INIS)

Pradeep, P.

1997-01-01

Thermal transport properties of powdered materials depend upon interstitial gas pressure. The present study reports the experimental results for the effective thermal conductivity of three rare earth oxide powders viz. yttrium oxide, samarium oxide, and gadolinium oxide, at various interstitial pressures by using transient plane source (TPS) method. A theoretical model is also proposed for the interpretation of the variation of the effective thermal conductivity with interstitial gas pressure. Its validity is found to be good in low pressure range of 45 mm Hg to normal pressure when compared with the experimental results. Also an attempt has been made to calculate the variation of thermal conductivity with interstitial pressure in the high pressure range up to 2 kbar using the proposed model. (author)

Structural studies of type N superconductive compounds: R2-xCexCuO4±δ (R = Gd, Eu, Sm, Nd, Pr); influences of chemical treatments on physical properties

International Nuclear Information System (INIS)

Vigoureux, P.

1995-06-01

Different chemical treatments of R 2-x Ce x CuO 4±δ compounds monocrystals (gadolinium, europium, samarium, neodymium and praseodymium cuprates) modify their physical properties especially their superconductive properties. The presented chemical treatments are: the substitution of the trivalent rare earth element R by an other trivalent lanthanide, its substitution by tetravalent cerium, and heat treatment under low oxygen pressure. After these chemical treatments, structural modifications are observed by neutrons and X-rays diffraction, and allow to precise their actions: size effect of the rare earth element on the deformation of the CuO 2 planes, links between deformation and superconductivity and magnetic properties. (A.B.)

Radiopharmaceuticals developed at the University of Missouri research reactor

International Nuclear Information System (INIS)

Ketring, A.R.; Ehrhardt, G.J.; Day, D.E.

1997-01-01

The University of Missouri Research Reactor (MURR) has put a great deal of effort in the last two decades into development of radiotherapeutic beta emitters as nuclear medicine radiotherapeutics for malignancies. This paper describes the development of two of these drugs, 153 Sm ethylenediaminetetra-methylene phosphonic acid (EDTMP) (Quadramet trademark) and 90 Y glass microspheres (TheraSphere trademark). Samarium-153 EDTMP is a palliative used to treat the pain of metastatic bone cancer without the side effects of narcotic pain killers. Yttrium-90 glass microspheres are delivered via hepatic artery catheter to embolize the capillaries of liver tumors and deliver a large radiation dose for symptom palliation and life prolonging purposes

Samarium-cobalt type rare earth permanent magnets

International Nuclear Information System (INIS)

Kamat, S.V.

2014-01-01

Permanent magnets are one of the oldest and largest applications of magnetic materials and form an integral part of our modern industrial society. They belong to a special class of functional materials and are characterized for remanence (flux output from the magnet), coercivity (resistance to demagnetization) and energy product (material energy density) from the second quadrant of the magnetic hysteresis loop. The reliability, stability, size, weight, cost and performance of many electro-technical devices depend mainly on the properties of permanent magnets used in them. There are three important families of permanent magnets viz., Ferrites, Alnicos and Rare Earth Permanent Magnets (REPMs) with energy product values ranging from 3 to 50 MGOe and among the front ranking high performance REPMs, SmCo 5 , Sm 2 Co 17 type and NdFeB alloys are technologically the most important materials. They are used in a wide range of applications ranging from consumer products to very specialized areas of tele-communications, microelectronics, defence, space, avionics etc. While NdFeB has the highest energy product, Sm-Co based magnets are preferred for most critical applications where temperature stability of magnetic properties is essential because of their significantly higher Curie temperatures. In this presentation some of the key challenges associated with these Sm-Co based rare earth permanent magnets will be highlighted. (author)

Samarium-cobalt-copper-iron-titanium permanent magnets

International Nuclear Information System (INIS)

Inomata, K.; Yamada, M.

1980-01-01

A permanent magnet, which comprises a composition containing a Sm-Co compound and consisting essentially of 23 to 30 wt.% of Sm, 0.2 to 1.5 wt.% Ti, 9 to 13 wt., Cu, 3 to 12 wt.% Fe and the balance Co, said magnet having a residual flux density (Br) of about 10 (kG), a coercive force (IC) of about 8 (KOe) and a maximum energy product (BH max) of about 25 (MGOe), having the aforesaid magnetic properties without the necessity of an ageing treatment

Radiolabelling of potential colonic delivery systems by neutron activation. An evaluation based on physiochemical properties of excipients and formulations

Energy Technology Data Exchange (ETDEWEB)

Ahrabi, Sayeh

1999-07-01

The effects of neutron irradiation on the physicochemical properties of some potential release-controlling excipients for oral delivery to colon (based on microbially degradable polysaccharide or a combination of pH- and time-dependent mechanisms) were initially investigated. The aim was to choose the most irradiation-resistant ones for the development of a colonic delivery system to be radiolabelled by the neutron activation procedure. However, no correlation between the extent of irradiation-induced changes of the release-controlling polymers and the in vitro properties of the final formulation was observed. Incorporation of samarium oxide (Sm{sub 2}O{sub 3}) resulted in retardation of the drug release through the diffusion layer. The influence of neutron activation factors on the properties of some suppository combinations was also studied. The effect of the admixture of Sm{sub 2}O{sub 3} on the dissolution and disintegration of the suppositories was more profound than the effect of neutron irradiation. In hydrophilic suppositories, the effect of Sm{sub 2}O{sub 3} was dependent on the type, amount and the physicochemical characteristics of the incorporated drug. In lipophilic suppositories, the release-controlling effect of Sm{sub 2}O{sub 3} was hypothesised to be due to its insoluble micronised particles blocking the drug diffusion layer. The neutron activation procedure could be utilised for radiolabelling potential oral and rectal colonic drug delivery systems. However, to avoid alteration in the crucial in vitro characteristics of the formulations, the amount, the particle size and the aggregated particle characteristics of the lanthanide salt (e.g. Sm{sub 2}O{sub 3} or samarium stearate) together with the neutron irradiation dose should be controlled precisely for each dosage system. For the systems investigated in this work the release-controlling mechanism of the dosage form seems to be a key parameter to predict the extent of the influence of neutron

Coupled IVPs to Investigate a Nuclear Reactor Poison Burn Up

Science.gov (United States)

Faghihi, F.; Saidi-Nezhad, M.

2009-09-01

A set of coupled IVPs that describe the change rate of an important poison, in a nuclear reactor, has been written herein. Specifically, in this article, we have focused on the samarium-149 (as a poison) burnup in a desired pressurized water nuclear reactor and its concentration are given using our MATLAB-linked "solver."

Coupled IVPs to Investigate a Nuclear Reactor Poison Burn Up

International Nuclear Information System (INIS)

Faghihi, F.

2009-01-01

A set of coupled IVPs that describe the change rate of an important poison, in a nuclear reactor, has been written herein. Specifically, in this article, we have focused on the samarium-149 (as a poison) burnup in a desired pressurized water nuclear reactor and its concentration are given using our MATLAB-linked 'solver'.

Xe-135 and Sm-149 Isotopic Evolution Analysis Xesamo code; Analisis de la Evolucion Isotopica del Xe-135 y Sm-149. Programa Xesamo

Energy Technology Data Exchange (ETDEWEB)

Caro, R; Gallego, J; Martinez Fanegas, R

1977-07-01

In this report the time evolution analysis of the nuclides concentration Xe-135 and Sm-149 as a function of the neutron flux is carried out. The neutron flux may be any function of time. It is analyzed as well the reactivity changes associated with the xenon and samarium concentration variations. (Author) 5 refs.

Xe-135 and Sm-149 Isotopic Evolution Analysis Xesamo code

International Nuclear Information System (INIS)

Caro, R.; Gallego, J.; Martinez Fanegas, R.

1977-01-01

In this report the time evolution analysis of the nuclides concentration Xe-135 and Sm-149 as a function of the neutron flux is carried out. The neutron flux may be any function of time. It is analyzed as well the reactivity changes associated with the xenon and samarium concentration variations. (Author) 5 refs

Structural and Spectroscopic Studies of Sm3+/CdS Nanocrystallites in Sol-Gel TiO2-ZrO2 Matrix

Science.gov (United States)

Karthika, S.; Prathibha, Vasudevan; Ann, Mary K. A.; Viji, Vidyadharan; Biju, P. R.; Unnikrishnan, N. V.

2014-02-01

A sol-gel method was used to prepare titania-zirconia matrices doped with Sm3+/CdS nanocrystallites. The structural properties of the matrices were characterized using transmission electron microscopy (TEM), thermogravimetric analysis (TGA), differential thermal analysis (DTA), and Fourier-transform infrared spectroscopy studies. The thermal stability of the material was determined by TGA/DTA analysis. The absorption spectrum shows the characteristic peaks of the Sm3+ ions and the absorption peak corresponding to the CdS nanocrystallites. The optical bandgap and size of the CdS nanoparticles were calculated from the absorption spectrum. From TEM, the interplanar distance ( d) was estimated to be 3.533 Å, which matches with the (1 0 0) plane of bulk CdS. The measurements yield a nanocrystallite size of around 7.8 nm. The optical absorption and emission spectra confirmed the formation of CdS nanoparticles along with samarium ions in the titania-zirconia matrices. The fluorescence intensity of the samarium ions was found to be greatly enhanced by codoping with CdS nanocrystallites.

Viability of biocompatible and biodegradable seeds production with incorporated radionuclides

International Nuclear Information System (INIS)

Roberto, W.S.; Pereira, M.M.; Vasconcelos, W.L.; Campos, T.P.R.

2000-01-01

The present work aims the development of radioactive seeds, biocompatible and biodegradable, with the objective of adding options in the cancer treatment. The work focus on the production of seeds biodegradable that incorporate radioisotopes with half life inferior than the degradation time of the material. The idea of producing devices with biodegradable materials impregnated with radioisotopes of short half life will offer new possibilities in the cancer treatment, since they can be used following the same procedures of the permanent interstitial brachytherapy, but using degradable materials compatible with the physiological environment. It will be discussed in particular the possible application of these seeds in the treatment of prostate cancer. A review of the subject and a preliminary evaluation of the viability of production of the seeds will be presented. The method of production of the seeds is based on the incorporation of Iodine and Samarium in glass matrixes obtained by sol-gel processing. X-ray fluorescence was done in the samples produced and the incorporation of Iodine and Samarium atoms was confirmed. (author)

Viability of biocompatible and biodegradable seeds production with incorporated radionuclides; Viabilidade da producao de sementes biocompativeis e biodegradaveis com radionuclideos incorporados

Energy Technology Data Exchange (ETDEWEB)

Roberto, W.S. [Centro Federal de Educacao Tecnologica de Ouro Preto (CEFET/OP), MG (Brazil); Pereira, M.M.; Vasconcelos, W.L.; Campos, T.P.R. [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)], e-mail: wanderley@nuclear.ufmg.br

2000-07-01

The present work aims the development of radioactive seeds, biocompatible and biodegradable, with the objective of adding options in the cancer treatment. The work focus on the production of seeds biodegradable that incorporate radioisotopes with half life inferior than the degradation time of the material. The idea of producing devices with biodegradable materials impregnated with radioisotopes of short half life will offer new possibilities in the cancer treatment, since they can be used following the same procedures of the permanent interstitial brachytherapy, but using degradable materials compatible with the physiological environment. It will be discussed in particular the possible application of these seeds in the treatment of prostate cancer. A review of the subject and a preliminary evaluation of the viability of production of the seeds will be presented. The method of production of the seeds is based on the incorporation of Iodine and Samarium in glass matrixes obtained by sol-gel processing. X-ray fluorescence was done in the samples produced and the incorporation of Iodine and Samarium atoms was confirmed. (author)

Study of rare earth separation by counter current electromigration

International Nuclear Information System (INIS)

Correa, Sergio Machado

1995-08-01

The counter current electromigration (CCEM) is an electrophoretic technique where the charged species migrate on an electrical field toward an electrolytic flux. Usually this electrolyte is a complexing agent and is necessary to increase the small differences between the species mobilities. A new column was developed, all made of acrylic, in a cylindrical shape. A set of experiments was carried out with the species Na + /K + , K + /Sm +3 , K + /Eu +3 and K + /Sm +3 /Eu +3 using the α-hydrox i-isobutyric acid o,01 M as the counter current electrolytic flux. From a synthetic mixture of 90% of samarium and 10% of europium was obtained the samarium ion in a purity better than 99,9% where the concentration of Eu was determined by the polarography technique. The potassium ion was used as a leading electrolyte. It was also measured the mobilities of the involved species in the α-HIBA medium. Two models are proposed, a stationary model and a dynamic one. A simulator of a simplified stationary model, prepared in FORTRAN language, was developed and tested toward experimental results. (author)

Contribution to the study of samarium-151 excited levels; Contribution a l'etude des niveaux excites du samarium-151

Energy Technology Data Exchange (ETDEWEB)

Locard, P [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Grenoble, 38 (France)

1967-07-01

The nucleus of {sup 151}Sm, which has 89 neutrons, happens to be on the lower edge of the deformed nuclei of region II. Therefore, the study of its levels is very interesting for the verification of the goodness of the collective models for deformed nuclei when the deformation is small (we introduce these models in the first chapter). {sup 151}Sm has often been studied, but the direct gamma spectrum measured with a lithium drift-germanium detector (chapter 3) shows many high energy transitions which did not appear in the previous level schemes. In order to settle these transitions, we have undertaken gamma-gamma coincidence spectra (as well as sum-coincidence spectra) experiments with a scintillation spectrometer designed in our laboratory (chapter 2). The investigation of the intensities of these coincidences leads us to modify the last proposed level schemes: we suppress the levels at 405,5 and 650 keV, we add levels at 245,6 - 306,6 - 522 - 952 and 962 keV. We have also verified the multipolarities of the main transitions and measured the half-lives of a few levels (chapter 3) (we find a half-life of 1.1 {+-} 0.5 nanosecond for the level at 167,7 keV). In chapter 4, we compare our results to the predictions of the models described in chapter 1. (author) [French] Le noyau de {sup 151}Sm, qui possede 89 neutrons, se trouve a la limite inferieure des noyaux deformes de la region II. L'etude de ses niveaux excites est donc d'un interet tout particulier pour la verification de la validite des differents modeles collectifs pour les noyaux deformes, lorsque la deformation est petite (nous introduisons ces modeles dans un premier chapitre). Le {sup 151}Sm a deja fait l'objet de nombreuses etudes, mais le spectre gamma direct fait avec une jonction de germanium compense au lithium (chapitre 3), nous a montre l'existence d'un grand nombre de transitions de hautes energies qui ne sont pas placees dans les schemas proposes jusqu'a ce jour. Pour preciser la place de ces transitions, nous avons donc entrepris des experiences de coincidences gamma-gamma (et de ''spectre de somme'') a l'aide d'un ensemble de spectrometrie a scintillation realise au laboratoire (chapitre 2). L'etude des intensites de ces coincidences (chapitre 3) nous amene a modifier le dernier schema propose: nous supprimons les niveaux a 405,5 et 650 keV, nous ajoutons des niveaux a 245,6 - 306,6 - 522 - 952 et 962 keV. Nous avons egalement verifie la multipolarite des principales transitions et mesure la duree de vie de certains des niveaux (chapitre 3) (nous trouvons une periode de 1,1 {+-} 0,5) nanoseconde pour le niveau a 167,7 keV). Le chapitre 4 est enfin consacre a la comparaison de nos resultats avec les predictions des differents modeles decrits au chapitre 1. (auteur)

Nuclear structure from radioactive decay

International Nuclear Information System (INIS)

Wood, J.L.

1991-01-01

This report discusses nuclear structure from radioactive decay of the following: Neutron-Deficient Iridium Isotopes; Neutron-Deficient Platinum Isotopes; Neutron-Deficient Gold Isotopes; Neutron-Deficient Mercury Isotopes; Neutron-Deficient Thallium Isotopes; Neutron-Deficient Lead Isotopes; Neutron-Deficient Samarium Isotopes; Neutron-Deficient Promethium Isotopes; Neutron-Deficient Neodymium Isotopes; and Neutron-Deficient Praseodymium Isotopes. Also discussed are Nuclear Systematics and Models

Alkaline earth metal and samarium co-doped ceria as efficient electrolytes

Science.gov (United States)

Ali, Amjad; Raza, Rizwan; Kaleem Ullah, M.; Rafique, Asia; Wang, Baoyuan; Zhu, Bin

2018-01-01

Co-doped ceramic electrolytes M0.1Sm0.1Ce0.8O2-δ (M = Ba, Ca, Mg, and Sr) were synthesized via co-precipitation. The focus of this study was to highlight the effects of alkaline earth metals in doped ceria on the microstructure, densification, conductivity, and performance. The ionic conductivity comparisons of prepared electrolytes in the air atmosphere were studied. It has been observed that Ca0.1Sm0.1Ce0.8O2-δ shows the highest conductivity of 0.124 Scm-1 at 650 °C and a lower activation energy of 0.48 eV. The cell shows a maximum power density of 630 mW cm-2 at 650 °C using hydrogen fuel. The enhancement in conductivity and performance was due to increasing the oxygen vacancies in the ceria lattice with the increasing dopant concentration. The bandgap was calculated from UV-Vis data, which shows a red shift when compared with pure ceria. The average crystallite size is in the range of 37-49 nm. DFT was used to analyze the co-doping structure, and the calculated lattice parameter was compared with the experimental lattice parameter.

Conductivity fluctuation in the high temperature superconductor with planar weight disparity Y{sub 0.5}Sm{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}}

Energy Technology Data Exchange (ETDEWEB)

Barrera, E.W.; Rojas Sarmiento, M.P.; Rincon, L.F.; Landinez Tellez, D.A.; Roa-Rojas, J. [Grupo de Fisica de Nuevos Materiales, Departamento de Fisica, Universidad Nacional de Colombia, A.A. 14490, Bogota DC (Colombia)

2007-07-01

The synthesis of the Y{sub 0.5}Sm{sub 0.5}Ba{sub 2}Cu{sub 3}O{sub 7-{delta}} superconducting material by the standard solid state reaction is reported. DC resistivity measurements reveal the improvement of the critical temperature (T{sub c}) when substitution of exact 50-50 mix of Yttrium and Samarium is performed. A bulk T{sub c} = 101 K was determined by the criterion of the maximum in the temperature derivative of electrical resistivity. Structure characterization by means the x-ray diffraction technique shows the crystalline appropriated distribution of Yttrium and Samarium to create substantial planar weight disparity (PWD) in alternating layers. This PWD increases T{sub c} in copper-oxide superconductors. In order to examine the effect of PWD on the pairing mechanism close to T{sub c}, conductivity fluctuation analysis was performed by the method of logarithmic temperature derivative of the conductivity excess. We found the occurrence of Gaussian and genuinely critical fluctuations. Our results are in agreement with reports on YBa{sub 2}Cu{sub 3}O{sub 7-{delta}}, but an enhancement of the Gaussian fluctuation regimes was experimentally detected as a result of the PWD. The correlations of the critical exponents with the dimensionality of the fluctuation system for each Gaussian regime were performed by using the Aslamazov-Larkin theory. The genuinely critical exponent is interpreted by the 3D-XY model as corresponding with the dynamical universality class of the E-model. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Structural studies of type N superconductive compounds: R{sub 2-x}Ce{sub x}CuO{sub 4{+-}{delta}} (R = Gd, Eu, Sm, Nd, Pr); influences of chemical treatments on physical properties; Etudes structurales des composes supraconducteurs de type N: R{sub 2-x}Ce{sub x}CuO{sub 4{+-}{delta}} (R = Gd, Eu, Sm, Nd, Pr); influences des traitements chimiques sur les proprietes physiques

Energy Technology Data Exchange (ETDEWEB)

Vigoureux, P

1995-06-01

Different chemical treatments of R{sub 2-x}Ce{sub x}CuO{sub 4{+-}{delta}} compounds monocrystals (gadolinium, europium, samarium, neodymium and praseodymium cuprates) modify their physical properties especially their superconductive properties. The presented chemical treatments are: the substitution of the trivalent rare earth element R by an other trivalent lanthanide, its substitution by tetravalent cerium, and heat treatment under low oxygen pressure. After these chemical treatments, structural modifications are observed by neutrons and X-rays diffraction, and allow to precise their actions: size effect of the rare earth element on the deformation of the CuO{sub 2} planes, links between deformation and superconductivity and magnetic properties. (A.B.). 394 refs/.

Radiopharmaceuticals developed at the University of Missouri research reactor

Energy Technology Data Exchange (ETDEWEB)

Ketring, A.R.; Ehrhardt, G.J. [Univ. of Missouri, Columbia, MO (United States); Day, D.E. [Univ. of Missouri, Rolla, MO (United States)

1997-12-01

The University of Missouri Research Reactor (MURR) has put a great deal of effort in the last two decades into development of radiotherapeutic beta emitters as nuclear medicine radiotherapeutics for malignancies. This paper describes the development of two of these drugs, {sup 153}Sm ethylenediaminetetra-methylene phosphonic acid (EDTMP) (Quadramet{trademark}) and {sup 90}Y glass microspheres (TheraSphere{trademark}). Samarium-153 EDTMP is a palliative used to treat the pain of metastatic bone cancer without the side effects of narcotic pain killers. Yttrium-90 glass microspheres are delivered via hepatic artery catheter to embolize the capillaries of liver tumors and deliver a large radiation dose for symptom palliation and life prolonging purposes.

A Novel Molecular Fluorescent Technique for Imaging the Somatostatin Receptor 2, Using a DOTATOC Lanthanide Conjugate

DEFF Research Database (Denmark)

Andersen, Rune Wiik; Prakash, Vineet; Stensballe, Allan

-functional DOTATOC component.                       METHOD AND MATERIALS            The chelation of Europium and Samarium to DOTATOC was proven using MALDI-TOF Mass Spectrometry. The rise in quantum yield between unchelated lanthanides and those bound by DOTATOC was examined using fluorescence spectroscopy...

Solid solutions in the system Nd2(SeO4)3 - Sm2(SeO4)3 - H2O

International Nuclear Information System (INIS)

Serebrennikov, V.V.; Tsybukova, T.N.; Velikov, A.A.

1984-01-01

Using the method of isothermal solubility at 25 deg C the system Nd 2 (SeO 4 ) 3 -Sm 2 (SeO 4 ) 3 -H 2 O has been studied. Roentgenographic recording of solid ''residues'' is realized. For solid solutions energies of interchange and formation heats are calculated. Formation heats of solid solutions on the basis of samarium selenates are also found experimentally

Thermoluminescent coactivated rare earth oxyhalide phosphors and x-ray image converters utilizing said phosphors

International Nuclear Information System (INIS)

Rabatin, J.G.

1984-01-01

Oxyhalides of lanthanum, gadolinium and lutetium coactivated with a first activator selected from bismuth and samarium to provide the color of light emission and a second coactivator (e.g. terbium or praseodymium) which increases the amount of stored energy in a stored radiographic latent image are found to be superior in their conversion efficiency of x-rays to visible light. (author)

Self-Q-switched ytterbium-doped cladding-pumped fibre laser

International Nuclear Information System (INIS)

Grukh, Dmitrii A; Kurkov, Andrei S; Razdobreev, I M; Fotiadi, A A

2002-01-01

A self-Q-switched ytterbium-doped double-clad fibre laser is described. A samarium-doped fibre is used as a filter for protecting a pump source. A fibre coupler is employed to obtain a nonlinear feedback. The mechanism of pulse formation in the laser is considered, and the dependence of its output pulse on the coupler parameters is studied. (solitons and optical fibers)

Fundamental studies on multicharged impurities of the Tokamaks

International Nuclear Information System (INIS)

Bernardi, J. de; Geller, R.; Jacquot, B.; Jacquot, C.

1979-11-01

We describe Micromafios which is an Ion source delivering particles up to completely stripped Carbon, Nitrogen and Oxygen ions. The beams are utilized on an experiment device for cross section measurements enabling fondamental studies for Tokamak impurity ions. The source is a miniaturized Supermafios device where the minimum B configuration is obtained with Samarium Cobalt magnetized Ferrites and a solenoidal axial field [fr

Therapy for bone pain palliation in skeletal metastases with Samarium -153 EDTMP (Indonesian experience)

International Nuclear Information System (INIS)

Purnomo, E.

2007-01-01

Full text: Radiopharmaceutical therapy may be used for the treatment of cases with painful skeletal metastases. We evaluate and want to share an experience with application and efficacy of Sm-153 EDTMP in palliative painful bone metastases therapy. Our aim was to determine the efficacy and toxicity of single-dose Sm- 153 EDTMP as a palliative treatment for painful skeletal metastases. Material and methods: we selected 18 patients (9 male, 9 female). The average age 35-65 years weight 40- 60 kg; with metastatic bone confirmed with bone scan examination. 6 with breast cancer, 5 with nasopharyngeal cancer, 5 with prostatic cancer, 2 with lung cancer were treated with 30 mCi ( 1110 MBq) Sm-153 EDTMP. All showed extensive metastatic bone disease. The patients were given intravenous injections of 30 mCi Sm-153 EDTMP, after reconditioning, hydration . We established intensity of pain, haematological parameters, scintigraphic, Karnofsky scale. Clinical assessment was performed one month later. Responses were classified in completed (good response), partial and absent taking into account symptoms and drugs reduction. The discontinuation or the reduction of analgesic drugs like opiate dosage was also considered as successful palliative results of the treatment. Result: pain relief was obtained in 16/18 patients, Sm-153 was effective in patients with reduced drug assumption. The response to Sm-153 was good in 14/18(77,7%) of the patients and partial in 3/18(16,6%) and no response in 1/18(0,5%). The application of Sm-153 in patients with painful disseminated bone metastases has a satisfactory pain alleviating effects. Sides effects were noted, decrease hemoglobin counts and white blood cell and platelets, which gradually returned to near normal after 6 weeks. Easy application and low cost and produced in own country are important factors. Conclusion: radiopharmaceutical therapy can be recommended because of the favorable palliation effect and the low cost of Sm-153, especially

Utilization of Samarium-153 in bone pain and bone tumours in dog

International Nuclear Information System (INIS)

Martin, V. de; Marques, F.L.N.; Okamoto, M.; Guimaraes, M.I.C.C.; Dias-Neto, A.; Fonseca, A.C.

1997-01-01

Full text: The experimental unit of of Centro de Medicina Nuclear of the University of Sao Paulo is working on the utilization of Sm-153-EDTMP, produced by IPEN/CNEN-SP (Brazil), for the treatment of bone pain due either inflammatory process or bone tumours spontaneously developed in dogs. The effect of the injection of the radiopharmaceutical (37 MBq/kg) were analysed by observing the animal behavior against the pain and the evolution of the clinical picture of the inflammatory process. The cases where tumours were diagnosed, bone scintigraphy was performed to follow-up the evolution of those tumours. Preliminary observations indicated that, especially in inflammatory process due to disc spondylitis, there was an improvement concerning pain and consequently a better condition of the life for those animals. Bone tumours even being more difficult to evaluate, have shown a favorable evolution concerning the reduction of pain and consequently the increase in the life span of the animals

Behavior of radioactive metal surrogates under various waste combustion conditions

International Nuclear Information System (INIS)

Yang, Hee Chul; Lee, Jae Hee; Kim, Jung Guk; Yoo, Jae Hyung; Kim, Joon Hyung

2002-01-01

A laboratory investigation of the behavior of radioactive metals under the various waste combustion atmospheres was conducted to predict the parameters that influence their partitioning behavior during waste incineration. Neodymium, samarium, cerium, gadolinium, cesium and cobalt were used as non-radioactive surrogate metals that are representative of uranium, plutonium, americium, curium, radioactive cesium, and radioactive cobalt, respectively. Except for cesium, all of the investigated surrogate metal compounds converted into each of their stable oxides at medium temperatures from 400 to 900 .deg. C, under oxygen-deficient and oxygen-sufficient atmospheres (0.001-atm and 0.21-atm O 2 ). At high temperatures above 1,400 .deg. C, cerium, neodymium and samarium in the form of their oxides started to vaporize but the vaporization rates were very slow up to 1500 .deg. C. Inorganic chlorine (NaCl) as well as organic chlorine (PVC) did not impact the volatility of investigated Nd 2 O 3 , CoO and Cs 2 O. The results of laboratory investigations suggested that the combustion chamber operating parameters affecting the entrainment of particulate and filtration equipment operating parameters affecting particle collection efficiency be the governing parameters of alpha radionuclides partitioning during waste incineration

Preparation and Luminescent Properties of the antibacterial materials of the La3+ Doped Sm3+-Hydroxyapatite

Science.gov (United States)

Lv, Yuguang; Shi, Qi; Jin, Yuling; Ren, Hengxin; Qin, Yushan; Wang, Bo; Song, Shanshan

2018-03-01

In this paper, the La3+-doped Sm3+ hydroxyapatite (La/Sm/HAP) complexes were prepared by a precipitation method. The sample was defined by IR spectra, fluorescence spectra and X ray diffraction analysis et al. The structure of complexes were discussed. The emission wavelength of heat treatment of Sm3+ do not change, but will affect the intensity of the peak Sm3+ luminescence properties and the occupy hydroxyapatite in the lattice Ca( II )and Ca( I ) loci with Sm3+ doped concentration and the proportion of the sintering temperature change and change: The nano hydroxyapatite complex of the La3+ doped samarium obtain the good fluorescence intensity, by La3+ doping content of Sm3+ were hydroxyapatite 6% (La3+, Sm3+ mole ratio) device. The complex of La3+ doped samarium HAP have Stable chemical property, fluorescence property and excellent biological activity. The ligand HAP absorbs energy or captures an electron-hole pair and then transfers it to the lanthanide ions. The catalytic activity influence of the La3+-doped Sm3+hydroxyapatite was discussed, the La/Sm/HAP had excellent antibacterial property, which used as potential biological antibacterial material.

Synthesis, crystal structure and thermal decomposition mechanism of the complex [Sm(p-BrBA)3bipy.H2O]2.H2O

International Nuclear Information System (INIS)

Zhang Haiyan; Zhang Jianjun; Ren Ning; Xu Suling; Tian Liang; Bai Jihai

2008-01-01

A new binuclear samarium (III) complex [Sm(p-BrBA) 3 bipy.H 2 O] 2 .H 2 O (p-BrBA = p-bromobenzoic acid; bipy = 2,2'-bipyridine) has been synthesized and characterized by elemental analysis, UV, IR, molar conductance and TG-DTG techniques. The structure of the complex was established by single crystal X-ray diffraction. It crystallizes in triclinic, space group P1-bar with a = 8.2476(7) A, b = 13.3483(10) A, c = 15.9035(13) A, α 73.9160(10) o , β = 78.9630(10) o , γ = 74.4770(10) o , Z = 1, D c 1.947 g cm -3 , F(000) = 910. The carboxylic groups are bonded to the samarium ion in two modes: bidentate bridging, monodentate. Each center Sm 3+ ion is eight-coordinated by one 2,2'-bipyridine molecular, four bidentate bridging and a monodentate carboxylic group, as well as one water molecular. The coordination polyhedron around each Sm 3+ ion can be described as bi-capped triangular prism geometry. The thermal decomposition behavior of the title complex in a static air atmosphere was investigated by TG-DTG and IR techniques

Study of rare earth separation by counter current electromigration; Estudo da separacao de terras raras por eletromigracao em contra corrente

Energy Technology Data Exchange (ETDEWEB)

Correa, Sergio Machado

1995-08-01

The counter current electromigration (CCEM) is an electrophoretic technique where the charged species migrate on an electrical field toward an electrolytic flux. Usually this electrolyte is a complexing agent and is necessary to increase the small differences between the species mobilities. A new column was developed, all made of acrylic, in a cylindrical shape. A set of experiments was carried out with the species Na{sup +}/K{sup +}, K{sup +}/Sm{sup +3}, K{sup +}/Eu{sup +3} and K{sup +}/Sm{sup +3}/Eu{sup +3} using the {alpha}-hydrox i-isobutyric acid o,01 M as the counter current electrolytic flux. From a synthetic mixture of 90% of samarium and 10% of europium was obtained the samarium ion in a purity better than 99,9% where the concentration of Eu was determined by the polarography technique. The potassium ion was used as a leading electrolyte. It was also measured the mobilities of the involved species in the {alpha}-HIBA medium. Two models are proposed, a stationary model and a dynamic one. A simulator of a simplified stationary model, prepared in FORTRAN language, was developed and tested toward experimental results. (author)

Molecular electrophosphorescence in (Sm, Gd)-β-diketonate complex blend for OLED applications

International Nuclear Information System (INIS)

Reyes, R.; Cremona, M.; Teotonio, E.E.S.; Brito, H.F.; Malta, O.L.

2013-01-01

In this work the preparation and characterization of the triple-layer organic light-emitting diode (OLED) using a mixture of the samarium and gadolinium β-diketonate complexes [Sm 0.5 Gd 0.5 (TTA) 3 (TPPO) 2 ] as emitting layer is reported. The OLED's devices contain 1-(3-methylphenyl)-1,2,3,4-tetrahydroquinoline-6-carboxyaldehyde-1, 1'-diphenylhydrazone (MTCD) as hole-transporting layer and tris(8-hydroxyquinoline aluminum) (Alq 3 ) as electron transporting layer. The electroluminescence spectrum present emission narrow bands from the 4 G 5/2 → 6 H J transitions (where J=5/2, 7/2 and 9/2) characteristic of the Sm 3+ ion. These sharp lines are overlapped with a broad band attributed to the electrophosphorescence from the T 1 →S 0 transition in the ligand TTA. The intramolecular energy transfer is discussed and applied on the change of the emission color of the organic LEDs at different bias voltages. - Highlights: ► Samarium and gadolinium complexes. ► OLED with complex blend (Sm,Gd). ► Electrophosphorescence emission detection. ► Application in OLED changing the color emission.

Clinical and clinicopathologic response of canine bone tumor patients to treatment with samarium-153-EDTMP

International Nuclear Information System (INIS)

Lattimer, J.C.; Corwin, L.A. Jr.; Stapleton, J.; Volkert, W.A.; Ehrhardt, G.J.; Ketring, A.R.; Anderson, S.K.; Simon, J.; Goeckeler, W.F.

1990-01-01

Forty dogs with spontaneous skeletal neoplasia were treated with 153Sm-EDTMP (ethylenediaminetetramethylene phosphonic acid). Both primary and metastatic lesions were treated. Two treatment regimes, a single (37 MBq (1.0 mCi)/kg dose or two 37 MBq (1.0 mCi)/kg doses separated by 1 wk) were tested. Response to treatment was varied. Large lesions with minimal tumor bone formation responded poorly, while primary lesions with substantial ossification usually exhibited a transient response. Small lesions with minimal lysis, metastatic lesions, and axial skeleton lesions generally responded well. The major adverse side effects of treatment were platelet and white blood cell count depression below baseline values for up to 4 wk (p less than 0.05). Minor depression of packed cell volume and transient elevation of serum alkaline phosphatase were also noted (p less than 0.05). No significant differences (p greater than 0.05) between the two treatment groups, either in treatment effect or undesirable side effects, were detected

Derivative spectrophotometry of cobalt alloys

International Nuclear Information System (INIS)

Spitsyn, P.K.

1985-01-01

The method of derivative spectrophotometry is briefly described, and derivative absorption spectra are presented for samarium, cobalt, and commercial Sm-Co alloys. It is shown that the use of derivative spectrophotometry not only improves the accuracy and selectivity of element determinations but also simplifies the analysis of alloys. Results of a statistical evaluation of the metrological characteristics of the analytical procedure described here are presented. 8 references

Nanocrystalline samarium oxide coated fiber optic gas sensor

International Nuclear Information System (INIS)

Renganathan, B.; Sastikumar, D.; Srinivasan, R.; Ganesan, A.R.

2014-01-01

Highlights: • This fiber optic gas sensor works at room temperature. • As-prepared and annealed Sm 2 O 3 nanoparticles are act as sensor materials. • Sm 2 O 3 clad modified fiber detect the ammonia, ethanol and methanol gases. • The response of evanescent wave loss has been studied for different concentrations. - Abstract: Nanocrystalline Sm 2 O 3 coated fiber optic sensor is proposed for detecting toxic gases such as ammonia, methanol and ethanol vapors. Sm 2 O 3 in the as prepared form as well as annealed form have been used as gas sensing materials, by making them as cladding of a PMMA fiber. The spectral characteristics of the Sm 2 O 3 gas sensor are presented for ammonia, methanol and ethanol gases with different concentrations ranging from 0 to 500 ppm. The sensor exhibits a linear variation in the output light intensity with the concentration. The enhanced gas sensitivity and selectivity of the sensor for ethanol is discussed briefly

Samarium-153 EDTMP therapy of disseminated skeletal metastasis

International Nuclear Information System (INIS)

Turner, J.H.; Martindale, A.A.; Fleay, R.F.; Hoffman, R.F.; Claringbold, P.G.

1989-01-01

153 Sm-EDTMP (ethylenediaminetetramethylene phosphonate), prepared from a kit, was administered to 28 patients in a clinical trial of therapy for painful skeletal metastases unresponsive to all conventional treatment. The 103 keV gamma emission of 153 Sm was utilized for prospective individual estimation of beta radiation absorbed dose to red marrow to minimize myelotoxicity and provide optimum internal radiotherapy to skeletal metastases in each patient. Pain relief occurred within 14 days of administration of 153 Sm-EDTMP in 15 of 19 patients (79%) who could vie evaluated at 6 weeks, when clinical response was maximal. Duration of response ranged from 4 to 35 weeks. Recurrence of pain responded to retreatment with 153 Sm-EDTMP in five of eight cases. No dose-response relationship was apparent for pain relief but reversible myelotoxicity was frequently observed at radiation absorbed doses to bone marrow ≥270 cGy. Dosimetry calculation was based on pharmacokinetic studies of a tracer administration of 153 Sm-EDTMP in each patient. Assumptions inherent in this prospective method of predicting dose to bone marrow were validated experimentally. Biodistribution studies in rats demonstrated rapid skeletal uptake and long term retention of 153 Sm-EDTMP in bone over 5 days. Urinary clearance accounted for 40% of injected dose, and less than 0.5% of administered activity was retained in non osseous tissue. Microdensitometry of autoradiographs of sheep vertebra and femur confirmed surface uptake of 153 Sm-EDTMP in cortical bone and demonstrated relatively high trabecular bone activity which is the major component of radiation absorbed dose to bone marrow. Haematological studies in rabbits showed 153 Sm-EDTMP-induced myelotoxicity to be transient and no histopathological abnormalities were demonstrable with doses ten times greater than those administered to patients. (orig.)

Samarium Polystibides Derived from Highly Activated Nanoscale Antimony.

Science.gov (United States)

Schoo, Christoph; Bestgen, Sebastian; Egeberg, Alexander; Klementyeva, Svetlana; Feldmann, Claus; Konchenko, Sergey N; Roesky, Peter W

2018-05-14

Zintl ions in molecular compounds are of fundamental interest for basic research and application. Two reactive antimony sources are presented that allow direct access to molecular polystibide compounds. These are Sb amalgam (Sb/Hg) and ultrasmall Sb 0 nanoparticles (d=6.6±0.8 nm), which were used independently as precursors for the synthesis of the largest f-element polystibide, [(Cp* 2 Sm) 4 Sb 8 ]. Whereas the reaction of the nanoparticles with [Cp* 2 Sm] directly led to [(Cp* 2 Sm) 4 Sb 8 ], Sm/Sb/Hg intermediates were isolated when using Sb/Hg as the precursor. These Sm/Sb/Hg intermediates [{(Cp* 2 Sm) 2 Sb} 2 (μ-Hg)] and [{(Cp* 2 Sm) 3 (μ 4 ,η 1:2:2:2 -Sb 4 )} 2 Hg] were synthetically trapped and structurally characterized, giving insight in the formation mechanism of polystibide compounds. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Hydroxyapatite synthesis and labelling with with Samarium-153

International Nuclear Information System (INIS)

Miranda, J.; Enciso, A.M.; Herrera, J.; Portilla, A.; Carrillo, D.

1999-01-01

153 Sm-labeled hydroxyapatite (HA) is used in synovectomy performed by radiation. HA was synthesized according to the method employed by Hayek and Newesely, using calcium nitrate and ammonium diacid phosphate in basic pH. Chemical characterization of HA was carried out by x-ray diffraction. HA labeling with Sm-153 is conducted using citric acid as ligand; radiochemical purity is greater than 99% and labeled particles are stable up to 9 days. This product is adequate to treat rheumatoid arthritis

Measurement of radiative lifetime in atomic samarium using ...

Indian Academy of Sciences (India)

2014-02-08

Feb 8, 2014 ... gations of radiative lifetime measurement of odd-parity energy level at ... introduced by an electronic delay generator between the two ... cascade repopulation and depopulation, Zeeman and hyperfine quantum beats [6]. The.

Optical properties of samarium doped zinc–tellurite glasses

Indian Academy of Sciences (India)

Unknown

Optical absorption spectra of these glasses were recorded in the range 300–700 nm at room ... cause of their potential as hosts of rare earth elements for ... nature of these glasses was examined by X-ray diffraction ... absorption coefficient).

A novel samarium complex with interesting photoluminescence and ...

African Journals Online (AJOL)

The 4,4'-Hbipy moieties, isolated nitrates and [Sm(H2O)4(NO3)3] species are held together via hydrogen bonds and p…p interactions to form a 3-D supramolecular framework. Luminescent investigation reveals a strong emission in blue region. Optical absorption spectrum of 1 reveals the presence of an optical gap of 3.60 ...

Optical characteristics of transparent samarium oxide thin films ...

Indian Academy of Sciences (India)

2016-10-07

Oct 7, 2016 ... The estimated direct optical band gap energy (Ed g) values were found to ... rpm substrate rotation and power of 150 W. The rate of deposition was 2 .... tion by annealing is due to the generation of oxygen vacancies due to ...

Analysis of the Metal Oxide Space Clouds (MOSC) HF Propagation Environment

Science.gov (United States)

Jackson-Booth, N.; Selzer, L.

2015-12-01

Artificial Ionospheric Modification (AIM) attempts to modify the ionosphere in order to alter the high frequency (HF) propagation environment. It can be achieved through injections of aerosols, chemicals or radio (RF) signals into the ionosphere. The Metal Oxide Space Clouds (MOSC) experiment was undertaken in April/May 2013 to investigate chemical AIM. Two sounding rockets were launched from the Kwajalein Atoll (part of the Marshall Islands) and each released a cloud of vaporized samarium (Sm). The samarium created a localized plasma cloud, with increased electron density, which formed an additional ionospheric layer. The ionospheric effects were measured by a wide range of ground based instrumentation which included a network of high frequency (HF) sounders. Chirp transmissions were made from three atolls and received at five sites within the Marshall Islands. One of the receive sites consisted of an 18 antenna phased array, which was used for direction finding. The ionograms have shown that as well as generating a new layer the clouds created anomalous RF propagation paths, which interact with both the cloud and the F-layer, resulting in 'ghost traces'. To fully understand the propagation environment a 3D numerical ray trace has been undertaken, using a variety of background ionospheric and cloud models, to find the paths through the electron density grid for a given fan of elevation and azimuth firing angles. Synthetic ionograms were then produced using the ratio of ray path length to speed of light as an estimation of the delay between transmission and observation for a given frequency of radio wave. This paper reports on the latest analysis of the MOSC propagation environment, comparing theory with observations, to further understanding of AIM.

Utilization of corn cob biochar in a direct carbon fuel cell

Science.gov (United States)

Yu, Jinshuai; Zhao, Yicheng; Li, Yongdan

2014-12-01

Biochar obtained from the pyrolysis of corn cob is used as the fuel of a direct carbon fuel cell (DCFC) employing a composite electrolyte composed of a samarium doped ceria (SDC) and a eutectic carbonate phase. An anode layer made of NiO and SDC is utilized to suppress the cathode corrosion by the molten carbonate and improves the whole cell stability. The anode off-gas of the fuel cell is analyzed with a gas chromatograph. The effect of working temperature on the cell resistance and power output is examined. The maximum power output achieves 185 mW cm-2 at a current density of 340 mA cm-2 and 750 °C. An anode reaction scheme including the Boudouard reaction is proposed.

'Transitorion' program for the simulation of the liquid zone evolution against power transients

International Nuclear Information System (INIS)

Coutsiers, Ernesto; Rabiti, Arnaldo; Pomerantz, Marcelo E.; Villar, Javier

2003-01-01

This work presents a program that allows to simulate the liquid zones evolution against power transients at Embalse nuclear power plant reactor. This program takes into account the dynamic effects of plutonium, samarium, xenon and iodine. It simulates also fuel burning, coolant void and the behavior of the reactor regulating system. The validation, based in the comparison with plant's real cases, gives a maximum error of 7% in liquid zone's average in periods of around 5 days. However, the typical adjustment has a lower error, around 2% in liquid zone's average. As the main conclusions of this work the good adjustment of the results of the code as well as the building of an important economic tool for the power plant could be highlighted. (author )

A gamma camera count rate saturation correction method for whole-body planar imaging

Science.gov (United States)

Hobbs, Robert F.; Baechler, Sébastien; Senthamizhchelvan, Srinivasan; Prideaux, Andrew R.; Esaias, Caroline E.; Reinhardt, Melvin; Frey, Eric C.; Loeb, David M.; Sgouros, George

2010-02-01

Whole-body (WB) planar imaging has long been one of the staple methods of dosimetry, and its quantification has been formalized by the MIRD Committee in pamphlet no 16. One of the issues not specifically addressed in the formalism occurs when the count rates reaching the detector are sufficiently high to result in camera count saturation. Camera dead-time effects have been extensively studied, but all of the developed correction methods assume static acquisitions. However, during WB planar (sweep) imaging, a variable amount of imaged activity exists in the detector's field of view as a function of time and therefore the camera saturation is time dependent. A new time-dependent algorithm was developed to correct for dead-time effects during WB planar acquisitions that accounts for relative motion between detector heads and imaged object. Static camera dead-time parameters were acquired by imaging decaying activity in a phantom and obtaining a saturation curve. Using these parameters, an iterative algorithm akin to Newton's method was developed, which takes into account the variable count rate seen by the detector as a function of time. The algorithm was tested on simulated data as well as on a whole-body scan of high activity Samarium-153 in an ellipsoid phantom. A complete set of parameters from unsaturated phantom data necessary for count rate to activity conversion was also obtained, including build-up and attenuation coefficients, in order to convert corrected count rate values to activity. The algorithm proved successful in accounting for motion- and time-dependent saturation effects in both the simulated and measured data and converged to any desired degree of precision. The clearance half-life calculated from the ellipsoid phantom data was calculated to be 45.1 h after dead-time correction and 51.4 h with no correction; the physical decay half-life of Samarium-153 is 46.3 h. Accurate WB planar dosimetry of high activities relies on successfully compensating

On three-dimensional nuclear thermo-hydraulic computation techniques for ATR

International Nuclear Information System (INIS)

1997-08-01

The three-dimensional computation code for nuclear thermo-hydraulic combination core LAYMON-2A is used for the calculation of the power distribution and the control rod reactivity value of the ATR. This code possesses various functions which are required for planning the core operation such as the search function for critical boric acid concentration, and can do various simulation calculations such as core burning calculation. Further, the three-dimensional analysis code for xenon dynamic characteristics in the core LAYMON-2C, in which the dynamic characteristic equation of xenon-samarium was incorporated into the LAYMON-2A code can take the change with time lapse of xenon-samarium concentration accompanying the change of power level and power distribution into account, and it is used for the analysis of the spatial vibration characteristics of power and the regional power control characteristics due to xenon in the core. As to the LAYMON-2A, the computation flow, power distribution and thermo-hydraulic computation models, and critical search function are explained. As to the LAYMON-2C, the computation flow is described. The comparison of the calculated values by using the LAYMON-2A code and the operation data of the Fugen is reported. (K.I.)

Neutron scattering studies of mixed-valence semiconductors

Energy Technology Data Exchange (ETDEWEB)

Mignot, J M [Laboratoire Leon Brillouin (LLB) - Centre d` Etudes de Saclay, 91 - Gif-sur-Yvette (France); Alekseev, P A [Kurchatov Institute, Moscow (Russian Federation)

1994-12-31

Neutron scattering experiments on the mixed-valence (MV) compounds SmB{sub 6} are reported. The inelastic magnetic response of SmB{sub 6} at T = 2 K, measured on a double-isotope single crystal,displays a strongly damped peak at 35 meV corresponding to the inter multiplet transition of Sm{sup 2+}. At lower energies ( h.{omega} {approx_equal} 14 meV), a narrow magnetic excitation is observed, with remarkable scattering-vector and temperature dependences of its intensity. This novel feature is discussed in terms of recent theoretical works describing the formation of an anisotropic local bound state in semiconducting MV materials. If the average samarium valence is decreased by substituting La for Sm, a peak is found to appear at high energies. The elastic magnetic form factor of SmB{sub 6} was determined using polarised neutrons and no significant difference is observed in its Q-dependence with respect to that of pure divalent samarium. This surprising behaviour is constant with previous measurements on the gold (high-pressure) phase of SmS. The above results are compared to those already reported for other MV materials. In particular existing information for TmSe is supplemented by recent inelastic scattering measurements carried out on a large stoichiometric single crystal. (author). 44 refs., 7 figs.

Molecular electrophosphorescence in (Sm, Gd)-{beta}-diketonate complex blend for OLED applications

Energy Technology Data Exchange (ETDEWEB)

Reyes, R., E-mail: fisicaplic@hotmail.com [Facultad de Ingenieria Quimica y Textil, Universidad Nacional de Ingenieria, UNI, Av. Tupac Amaru 210, Lima 31, Peru (Peru); Cremona, M. [DIMAT - Divisao de Metrologia de Materiais, Instituto Nacional de Metrologia, Normalizacao e Qualidade Industrial, INMETRO, Duque de Caxias, RJ (Brazil); Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, PUC-Rio, C.P. 38071, Rio de Janeiro, RJ, CEP 22453-970 (Brazil); Teotonio, E.E.S. [Departamento de Quimica, CCEN, Universidade Federal da Paraiba, UFPB, C.P. 5093, Joao Pessoa, PB, CEP 5805-970 (Brazil); Brito, H.F. [Instituto de Quimica, Universidade de Sao Paulo, USP, C.P. 26077, Sao Paulo, SP, CEP 05599-970 (Brazil); Malta, O.L. [Departamento de Quimica Fundamental, CCEN, Universidade Federal de Pernambuco, Cidade Universitaria, Recife, PE, CEP 50670-901 (Brazil)

2013-02-15

In this work the preparation and characterization of the triple-layer organic light-emitting diode (OLED) using a mixture of the samarium and gadolinium {beta}-diketonate complexes [Sm{sub 0.5}Gd{sub 0.5}(TTA){sub 3}(TPPO){sub 2}] as emitting layer is reported. The OLED's devices contain 1-(3-methylphenyl)-1,2,3,4-tetrahydroquinoline-6-carboxyaldehyde-1, 1'-diphenylhydrazone (MTCD) as hole-transporting layer and tris(8-hydroxyquinoline aluminum) (Alq{sub 3}) as electron transporting layer. The electroluminescence spectrum present emission narrow bands from the {sup 4}G{sub 5/2}{yields}{sup 6}H{sub J} transitions (where J=5/2, 7/2 and 9/2) characteristic of the Sm{sup 3+} ion. These sharp lines are overlapped with a broad band attributed to the electrophosphorescence from the T{sub 1}{yields}S{sub 0} transition in the ligand TTA. The intramolecular energy transfer is discussed and applied on the change of the emission color of the organic LEDs at different bias voltages. - Highlights: Black-Right-Pointing-Pointer Samarium and gadolinium complexes. Black-Right-Pointing-Pointer OLED with complex blend (Sm,Gd). Black-Right-Pointing-Pointer Electrophosphorescence emission detection. Black-Right-Pointing-Pointer Application in OLED changing the color emission.

First calorimetric determination of heat of extraction of 248Cm in a bi-phasic system

International Nuclear Information System (INIS)

Martin, Leigh R.; Zalupski, Peter R.

2011-01-01

This report presents a summary of the work performed to meet FCR and D level 2 milestone M21SW050201, 'Complete the first calorimetric determination of heat of extraction of 248Cm in a bi-phasic system'. This work was carried out under the auspices of the Thermodynamics and Kinetics FCR and D work package. To complement previous work undertaken under this work package we have extended out heat of extraction studies by di-2-ethyl-hexyl-phosphoric acid to curium. This report also details the heat of extraction of samarium in the same system. This work was performed to not only test the methodology but also to check for consistency with the heats of extraction obtained with those in the prior literature. The heat of extraction for samarium that was obtained in this study was -9.6 kJ mol-1, which is in reasonable agreement with the previously obtained value of -10.9 kJ mol-1. The curium heat of extraction was performed under two sets of conditions and the obtained heats of extraction were in reasonable agreement with each other at -16.0 ± 1.1 and -16.8 ± 1.5 kJ mol-1.

Obsidian sources characterized by neutron-activation analysis.

Science.gov (United States)

Gordus, A A; Wright, G A; Griffin, J B

1968-07-26

Concentrations of elements such as manganese, scandium, lanthanum, rubidium, samarium, barium, and zirconium in obsidian samples from different flows show ranges of 1000 percent or more, whereas the variation in element content in obsidian samples from a single flow appears to be less than 40 percent. Neutron-activation analysis of these elements, as well as of sodium and iron, provides a means of identifying the geologic source of an archeological artifact of obsidian.

Reductive Bis-addition of Aromatic Aldehydes to α,β-Unsaturated Esters via the Use of Sm/Cu(I) in Air: A Route to the Construction of Furofuran Lignans.

Science.gov (United States)

Liu, Yongjun; Tian, Guang; Li, Jingjing; Qi, Yan; Wen, Yonghong; Du, Feng

2017-06-02

The novel bis-addition of benzaldehydes to acrylates or maleates was achieved by the direct use of samarium metal with the assistance of CuI under mild conditions under dry air, and the useful 2-hydroxylalkyl-γ-butyrolactons and lignan derivatives were thus constructed with high efficiency. The key factors that influence the reaction efficiency were investigated. The use of potassium iodide and molecular sieves as additives can improve the reaction efficiency remarkably.

JPRS Report Proliferation Issues

Science.gov (United States)

1991-10-29

MVLIS) which utilizes carbon dioxide lasers. such an experience in the United States or Europe. They were able to go into uranium enrichment and repro...yttrium, is used like phosphorous in color television Rhodia, Paranapanema, the Belgian Solvay group, and sets. By combining samarium with neodymium, two...use presently. There have been some using thorium and U-233. problems centering on the liquid sodium coolant used in FBTR reportedly accentuated by use

Sm and Y radiolabeled magnetic fluids: magnetic and magneto-optical characterization

Energy Technology Data Exchange (ETDEWEB)

Aquino, R. [Complex Fluids Group, Instituto de Quimica, Universidade de Brasilia, Caixa Postal 04478, 70919-970 Brasilia (DF) (Brazil) and Laboratoire des Milieux Deet Heterogenes, Universite Pierre et Marie Curie (Paris 6), Site de Boucicaut, case 86, 140, Rue de Lourmel, 75015 Paris (France)]. E-mail: reaquino@unb.br; Gomes, J.A. [Complex Fluids Group, Instituto de Fisica, Universidade de Brasilia, 70919-970 Brasilia (DF) (Brazil); Tourinho, F.A. [Complex Fluids Group, Instituto de Quimica, Universidade de Brasilia, Caixa Postal 04478, 70919-970 Brasilia (DF) (Brazil); Dubois, E. [Laboratoire des Liquides Ioniques et Interfaces Chargees, Universite Pierre et Marie Curie (Paris 6), Batiment F, Case 63, 4 place Jussieu, 75252 Paris Cedex 05 (France); Perzynski, R. [Laboratoire des Milieux Deet Heterogenes, Universite Pierre et Marie Curie (Paris 6), Site de Boucicaut, case 86, 140, Rue de Lourmel, 75015 Paris (France); Silva, G.J. da [Complex Fluids Group, Instituto de Fisica, Universidade de Brasilia, 70919-970 Brasilia (DF) (Brazil); Depeyrot, J. [Complex Fluids Group, Instituto de Fisica, Universidade de Brasilia, 70919-970 Brasilia (DF) (Brazil)

2005-03-15

We report on magnetic fluids based on samarium and ytrium-doped nanoparticles. The nanostructures chemical composition is checked and X-ray diffraction provides both their mean size and a structural characterization. Magnetization and magneto-optical birefringence results are presented and well agree with the pure maghemite behavior. Since these particles can become radioactive after neutron activation, they could therefore represent a new perspective for biomedical applications in the radiation therapy of cancer.

Sm and Y radiolabeled magnetic fluids: magnetic and magneto-optical characterization

Science.gov (United States)

Aquino, R.; Gomes, J. A.; Tourinho, F. A.; Dubois, E.; Perzynski, R.; da Silva, G. J.; Depeyrot, J.

2005-03-01

We report on magnetic fluids based on samarium and ytrium-doped nanoparticles. The nanostructures chemical composition is checked and X-ray diffraction provides both their mean size and a structural characterization. Magnetization and magneto-optical birefringence results are presented and well agree with the pure maghemite behavior. Since these particles can become radioactive after neutron activation, they could therefore represent a new perspective for biomedical applications in the radiation therapy of cancer.

Sm and Y radiolabeled magnetic fluids: magnetic and magneto-optical characterization

International Nuclear Information System (INIS)

Aquino, R.; Gomes, J.A.; Tourinho, F.A.; Dubois, E.; Perzynski, R.; Silva, G.J. da; Depeyrot, J.

2005-01-01

We report on magnetic fluids based on samarium and ytrium-doped nanoparticles. The nanostructures chemical composition is checked and X-ray diffraction provides both their mean size and a structural characterization. Magnetization and magneto-optical birefringence results are presented and well agree with the pure maghemite behavior. Since these particles can become radioactive after neutron activation, they could therefore represent a new perspective for biomedical applications in the radiation therapy of cancer

The effect of CTAB on synthesis in butanol of samaria and gadolinia doped ceria - nickel oxide ceramics

International Nuclear Information System (INIS)

Arakaki, A.R.; Cunha, S.M.; Yoshito, W.K.; Ussui, V.; Lazar, D.R.R.

2011-01-01

In this work it was synthesized doped ceria and Samaria gadolinia - nickel oxide ceramics, mainly applied as anodes Fuel Cells Solid Oxide. Powders of composition Ce 0,8 (SmGd) 0,2 O 1,9 /NiO and mass ratio of 40: 60% were initially synthesized by hydroxides coprecipitation and then treated solvo thermically in butanol. Cerium samarium, gadolinium and nickel chlorides and CTAB with molar ratio metal / CTAB ranging from 1 to 3, were used as raw materials Powders were treated in butanol at 150 deg C for 16h. The powders were analyzed by X-ray diffraction, scanning electron microscopy, specific surface area for adsorption of nitrogen and particle size distribution by laser beam scattering. The ceramics were analyzed by scanning electron microscopy and density measurements by immersion technique in water. The results showed that the powders had the characteristic crystalline structures of ceria and nickel hydroxide, and high specific surface area (80 m 2 / g). The characterizations of ceramics demonstrated high chemical homogeneity and porosity values of 30%. (author)

Preparation and luminescence properties of Ca3(VO4)2: Eu3+, Sm3+ phosphor for light-emitting diodes

International Nuclear Information System (INIS)

Huang Jiaping; Li Qiuxia; Chen Donghua

2010-01-01

Rare-earth ions co-activated red phosphors Ca 3 (VO 4 ) 2 : Eu 3+ , Sm 3+ were synthesized by modified solid-state reactions. The samples were characterized by X-ray powder diffractometer (XRD), energy-dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and luminescence spectrometer (LS). The results showed that the Eu-Sm system exhibits higher emission intensity than those of the Eu single-doped system and Sm separate-doped system under blue light. Samarium (III) ions are effective in broadening and strengthening absorptions around 467 nm. Furthermore, they exhibit enhanced luminescence emission. Luminescent measurements showed that the phosphors can be efficiently excited by ultraviolet (UV) to visible region, emitting a red light with a peak wavelength of 616 nm. The material has potential application as a phosphor for light-emitting diodes (LEDs).

Structural phase transition and elastic properties of samarium monopnictides

International Nuclear Information System (INIS)

Pagare, Gitanjali; Chouhan, Sunil Singh; Soni, Pooja; Sanyal, Sankar P.

2011-01-01

In recent years the monopnictides and monochalcogenides of the rare-earth elements with rocksalt structure (B 1 ) have aroused intensive interest due to the presence of strongly correlated f electrons in them. Under pressure, the nature of f-electrons of these compounds can be changed from localized to itinerant leading to significant changes in physical and chemical properties. These unusual structural, electronic, and high-pressure properties make them candidates for advanced industrial applications. For these applications they provide unique physical properties which cannot be achieved with other materials

Optical properties of lead–tellurite glasses doped with samarium ...

Indian Academy of Sciences (India)

Administrator

392. Table 1. Density, molar volume, optical energy bandgap, refractive index, molar refraction and polarizability of oxide ion for. Sm2O3–PbO–TeO2 glasses. Glass composition (mol%). Energy. Molar. Polarizability. Density Molar volume bandgap. Refractive refraction. (αe). Sm2O3. PbO. TeO2. (ρ) (g/cm. 3. ) (Vm) (cm. –3. ).

150 KVA Samarium Cobalt VSCF Starter Generator Electrical System

Science.gov (United States)

1978-12-01

4140 material where inertia welded for the bearing journals and spline interfaces. * Hub - The hub material is ’knconel 750" and is heat treated It...radial Conrad con- struction. The bearing balls and rings were vacuum melted AISI U50 tool steel, beat stabilized, and manu- factored to ABEC-7

Simulated samarium-neodymium thermochronology of garnet-clinopyroxene-plagioclase granulites

International Nuclear Information System (INIS)

Munha, J; Moita, P; Palacios, T

2001-01-01

Cooling and uplift histories (thermochronology) of metamorphic belts can be inferred from radiometric ages measured for appropriate geochronological systems (e.g., McDougall and Harrison, 1999). The strength of this approach lies on the potential to relate radiometric ages to the geothermobarometric conditions of mineral crystallization, and it depends on the interpretation that ages recorded by each decay system correspond to a particular temperature, the 'closure' temperature (Dodson, 1973), yielding a temperature vs. time path. However, closure temperatures should not have a single value for each decay system, since they are expected to be a function of several variables; therefore, it is crucial to assess the relative significance of all influential parameters in order to establish a rigorous thermochronological characterization of metamorphic rocks. Sm-Nd mineral geochronology has been widely used for dating high-grade rocks, including garnet(gt)- clinopyroxene(cpx)-plagioclase(pl) granulites (e.g., Burton et al., 1995). 'Real' ages of granulitic metamorphism and radiometric dates rarely coincide because the measured ages reflect only a fraction of the temperature - time path of the metamorphic process; this is the time during which each rock phase behaved essentially as a closed system, reflecting the progressive blocking of diffusion-limited isotope exchanges between coexisting minerals. The present study is an attempt to assess the time (temperature) bias between the metamorphic thermal peak event and the ages (apparent closure temperatures) obtained through the application of standard Sm-Nd geochronological methods. In particular, the model simulates the influence of variable (initial/boundary) conditions on radiometric ages that would be obtained from 147 Sm/ 144 Nd - 143 Nd/ 14 24Nd systematics of gt - cpx - pl mineral pairs; it should provide preliminary guidance on thermochronological studies of granulitic terranes (au)

Enantioselective cyclizations and cyclization cascades of samarium ketyl radicals

Science.gov (United States)

Kern, Nicolas; Plesniak, Mateusz P.; McDouall, Joseph J. W.; Procter, David J.

2017-12-01

The rapid generation of molecular complexity from simple starting materials is a key challenge in synthesis. Enantioselective radical cyclization cascades have the potential to deliver complex, densely packed, polycyclic architectures, with control of three-dimensional shape, in one step. Unfortunately, carrying out reactions with radicals in an enantiocontrolled fashion remains challenging due to their high reactivity. This is particularly the case for reactions of radicals generated using the classical reagent, SmI2. Here, we demonstrate that enantioselective SmI2-mediated radical cyclizations and cascades that exploit a simple, recyclable chiral ligand can convert symmetrical ketoesters to complex carbocyclic products bearing multiple stereocentres with high enantio- and diastereocontrol. A computational study has been used to probe the origin of the enantioselectivity. Our studies suggest that many processes that rely on SmI2 can be rendered enantioselective by the design of suitable ligands.

Preparation of radiopharmaceutical formulations; Fremstilling av radioaktive farmasoeytiske blandinger

Energy Technology Data Exchange (ETDEWEB)

Simon, J.; Garlich, J.R.; Frank, R.K.; McMillan, K

1998-03-16

Radiopharmaceutical formulations for complexes comprising at least one radionuclide complexed with a ligand, or its physiologically-acceptable salts thereof, especially {sup 153}samarium-ethylenediaminetetramethylenephosphonic acid, which optionally contains a divalent metal ion, e.g. calcium, and is frozen, thawed, and then administered by injection. Alternatively, the radiopharmaceutical formulations must contain the divalent metal and are frozen only if the time before administration is sufficiently long to cause concern for radiolysis of the ligand. 2 figs., 9 tabs.

Preparation of radiopharmaceutical formulations

International Nuclear Information System (INIS)

Simon, J.; Garlich, J.R.; Frank, R.K.; McMillan, K.

1998-01-01

Radiopharmaceutical formulations for complexes comprising at least one radionuclide complexed with a ligand, or its physiologically-acceptable salts thereof, especially 153 samarium-ethylenediaminetetramethylenephosphonic acid, which optionally contains a divalent metal ion, e.g. calcium, and is frozen, thawed, and then administered by injection. Alternatively, the radiopharmaceutical formulations must contain the divalent metal and are frozen only if the time before administration is sufficiently long to cause concern for radiolysis of the ligand. 2 figs., 9 tabs

Investigation of adducts of tris-(acetylacetonato)lanthanides with o-phenanthroline and α,α'-dipyridyl by mass spectroscopy

International Nuclear Information System (INIS)

Gavrishchuk, E.M.; Dzyubenko, N.G.; Martynenko, L.I.

1984-01-01

Mass spectra of adducts of tris-acetylacetonates of REE (REE, Ln, M) with O-phenanthroline (Phen) and α, α 1 -dipyridyl (Dipy) are obtained. A scheme of fragmentation is suggested. Peculiarities of dissociative ionization processes for samarium-, europium-thulium-, and ytterbium compounds are shown to be determined by a possibility of changing the oxidation state of a central ion. Energy characteristics of separation of the first and second ligands of compleXes in the entire REE series are compared

Effects of nanostructuring on luminescence properties of SrS:Ce,Sm phosphor: An experimental and phenomenological study

Science.gov (United States)

Yazdanmehr, Mohsen; Sadeghi, Hossein; Tehrani, Masoud Kavosh; Hashemifar, Seyed Javad; Mahdavi, Mohammad

2018-01-01

In this work, we employ various experimental techniques to illustrate the effects of nanostructuring on improvement of the luminescence properties of the polycrystalline SrS co-activated by cerium and samarium dopants (SrS : Ce , Sm). The nano and microstructure SrS : Ce , Sm powders were synthesized by the co-precipitation and solid state diffusion methods, respectively, followed by the spark plasma sintering (SPS) process to densify powders into pellet shape. It is observed that the photo-luminescence (PL), radio-luminescence (RL), and optically stimulated luminescence (OSL) emission intensity of the nanostructure samples are significantly improved with respect to the microstructure samples. Moreover, by using an accurate photomultiplier tube, we measured the CW-OSL decay curves of the samples to demonstrate much higher and faster sensitivity of the nanostructure SrS : Ce , Sm for in-flight and online OSL radiation dosimetry. The obtained absorption and emission spectra are used for phenomenology of the electronic band structure of the SrS : Ce , Sm micro and nano-phosphors inside the band gap. The proposed phenomenological electronic structures are then used to clarify the role of Ce3+ and Sm3+ localized energy levels in the luminescence properties of the nano and microstructure samples. It is argued that electronic transitions from the 2T2g state of Ce3+ and the 4G5/2 state of Sm3+ have strong contribution to the PL and RL emission spectra, while in the OSL mechanism, the Sm3+ 4G5/2 state is mainly responsible for electrons trapping.

Scanning Electron Microscope-Cathodoluminescence Analysis of Rare-Earth Elements in Magnets.

Science.gov (United States)

Imashuku, Susumu; Wagatsuma, Kazuaki; Kawai, Jun

2016-02-01

Scanning electron microscope-cathodoluminescence (SEM-CL) analysis was performed for neodymium-iron-boron (NdFeB) and samarium-cobalt (Sm-Co) magnets to analyze the rare-earth elements present in the magnets. We examined the advantages of SEM-CL analysis over conventional analytical methods such as SEM-energy-dispersive X-ray (EDX) spectroscopy and SEM-wavelength-dispersive X-ray (WDX) spectroscopy for elemental analysis of rare-earth elements in NdFeB magnets. Luminescence spectra of chloride compounds of elements in the magnets were measured by the SEM-CL method. Chloride compounds were obtained by the dropwise addition of hydrochloric acid on the magnets followed by drying in vacuum. Neodymium, praseodymium, terbium, and dysprosium were separately detected in the NdFeB magnets, and samarium was detected in the Sm-Co magnet by the SEM-CL method. In contrast, it was difficult to distinguish terbium and dysprosium in the NdFeB magnet with a dysprosium concentration of 1.05 wt% by conventional SEM-EDX analysis. Terbium with a concentration of 0.02 wt% in an NdFeB magnet was detected by SEM-CL analysis, but not by conventional SEM-WDX analysis. SEM-CL analysis is advantageous over conventional SEM-EDX and SEM-WDX analyses for detecting trace rare-earth elements in NdFeB magnets, particularly dysprosium and terbium.

Improved transistor-controlled and commutated brushless DC motors for electric vehicle propulsion

Science.gov (United States)

Demerdash, N. A.; Miller, R. H.; Nehl, T. W.; Nyamusa, T. A.

1983-01-01

The development, design, construction, and testing processes of two electronically (transistor) controlled and commutated permanent magnet brushless dc machine systems, for propulsion of electric vehicles are detailed. One machine system was designed and constructed using samarium cobalt for permanent magnets, which supply the rotor (field) excitation. Meanwhile, the other machine system was designed and constructed with strontium ferrite permanent magnets as the source of rotor (field) excitation. These machine systems were designed for continuous rated power output of 15 hp (11.2 kw), and a peak one minute rated power output of 35 hp (26.1 kw). Both power ratings are for a rated voltage of 115 volts dc, assuming a voltage drop in the source (battery) of about 5 volts. That is, an internal source voltage of 120 volts dc. Machine-power conditioner system computer-aided simulations were used extensively in the design process. These simulations relied heavily on the magnetic field analysis in these machines using the method of finite elements, as well as methods of modeling of the machine power conditioner system dynamic interaction. These simulation processes are detailed. Testing revealed that typical machine system efficiencies at 15 hp (11.2 kw) were about 88% and 84% for the samarium cobalt and strontium ferrite based machine systems, respectively. Both systems met the peak one minute rating of 35 hp.

Some practical applications of an ICP-MS instrument

International Nuclear Information System (INIS)

Meddings, B.; Ng, R.

1987-01-01

An early model commercial ICP-MS instrument (PlasmaQuad from VG Isotopes Limited) was acquired more than two years ago. As a typical analytical laboratory in the metallurgical field, the application of the ICP-MS technique to real sample analysis is the authors prime concern. The process of introducing this state-of-the-art instrument into routine analysis will be described. The modifications and limitations necessary to achieve acceptable precision under normal working conditions will be outlined. In most cases, practical problems can be circumvented with some sacrifice in analytical performance in the area of detection limits and dynamic range. In this presentation, specific applications of the ICP-MS technique in the authors laboratory will be discussed. These include trace analysis on high purity metals such as copper, aluminum, cobalt, nickel etc., on refinery feed samples such as nickel sulfate, mixed cobalt and nickel sulfide, cobalt cathode, samarium oxide etc., on alloys such as cobalt-samarium magnetic materials, nickel or cobalt based alloys used in turbine blades etc. Other applications such as the determination of uranium in phosphate rock, trace analysis on fertilizers, water samples and high purity acids will also be mentioned. The solutions to the practical problems encountered in these applications will be discussed. The analytical power of the ICP-MS technique for real sample analysis will be assessed

BIPR-5 program

International Nuclear Information System (INIS)

Petrunin, D.M.; Belyaeva, E.D.; Kireeva, I.L.

1975-01-01

The BIPR-5 program, which solves the relevant one-group equation in a three-dimensional inhomogeneous WWER reactor, makes it possible to simulate all the principal states of the core, including the maintenance of the critical state by means of rods or a liquid absorber on fuel burn-up or in transitional processes on xenon and samarium. The present paper includes a brief description of the program structure and a detailed description of input data and actually represents maintenance instructions

Structural aspects of displacive transformations: what can optical microscopy contribute? Dehydration of Sm2(C2O43·10H2O as a case study

Directory of Open Access Journals (Sweden)

Alexander A. Matvienko

2017-09-01

Full Text Available For martensitic transformations the macroscopic crystal strain is directly related to the corresponding structural rearrangement at the microscopic level. In situ optical microscopy observations of the interface migration and the change in crystal shape during a displacive single crystal to single crystal transformation can contribute significantly to understanding the mechanism of the process at the atomic scale. This is illustrated for the dehydration of samarium oxalate decahydrate in a study combining optical microscopy and single-crystal X-ray diffraction.

Optical isotype shifts of 146Sm and 151Sm

International Nuclear Information System (INIS)

Eastham, D.A.; Walker, P.M.; Griffith, J.A.R.; Evans, D.E.; England, J.G.; Grant, I.S.

1984-01-01

We have measured the optical isotope shifts of 146 Sm and 151 Sm by laser resonance fluorescence. From these measurements the changes in the mean square nuclear radii are: delta 2 > (A=144 to 146)=0.266(10) fm 2 , and delta 2 > (A=151 to 152)=0.262(10) fm 2 . These results, together with those of the stable isotopes, show that the average nuclear expansion of samarium can be accounted for by the liquid drop model with deformations. (orig.)

Geochronology Intermediary Laboratory implantation at the Rio Grande do Norte Federal University: the dating of the Serrinha Granitoid (RN) and the correlate Brasiliana extensional deformation

International Nuclear Information System (INIS)

Macedo, Maria Helena F.; Sa, Emanuel F. Jardim de; Souza, Zorano S.; Mendes, Franklin S.; Ramalho, Karlos A.C.

1997-01-01

The article describes the activities developed by the Geochronology Intermediary Laboratory at the Federal University of the Rio Grande do Norte, a Brazilian university, where there were the preoccupation of establishing strategies for a geochronological development. It relates the Rubidium-Strontium (Rb/Sr) and Samarium-Neodymium (Sm/Nd) methods, describing the analysis realized in these methodologies. Afterward, it presents the geological and petrographic situation of the Granitoide de Serrinha, located at Rio Grande do Norte State, Brazil and its geochronological data

Labeling of fruitflies and their identification by tracer activation

International Nuclear Information System (INIS)

Haisch, A.; Forster, S.; Staerk, H.

1975-01-01

A technique was worked out to label and identify cherry fruit flies (Rhagoletic cerasi L.) in large numbers. For that purpose, the tracers dysprosium and samarium were mingled with a carrier substance (silica gel) which, mixed with silica sand, formed the substrate for emergence. The flies, the pupae of which were in this substrate, took up with their ptilinum-labeled silica gel during their crawling through the sand up to the surface. The tracer was detected after its activation by neutron irradiation

UABUC - Single energy point model burnup computer code for water reactors

International Nuclear Information System (INIS)

El-Meshad, Y.; Morsy, S.; El-Osery, I.A.

1981-01-01

UABUC is a single energy point reactor burnup computer program in FORTRAN language. The program calculates the change in the isotopic composition of the uranium fuel as a function of irradiation time with all its associated quantities such as the average point flux, the conversion ratio, macroscopic fuel cross sections, and the point reactivity profile. A step-wise time analytical solution was developed for the nonlinear first order burnup differential equations. The ''Westcott'' convention of the effective cross sections was used except for plutonium-240 and uranium-238. For plutonium-240, an effective microscopic cross section was derived from the direct physical arguments taking into account the selfshielding effect of plutonium-240 as well as the 1 ev. resonance absorption. For uranium-238, an effective cross section, reflecting the effect of fast fission and resonance absorption was used. The fission products were treated in the three groups with 50, 300, and 800 barns. The yields in the groups were treated as functions of the type of fissionable nuclides, the effective neutron temperature, and the epithermal index. Xenon-135 and Samarium-149 were treated separately as functions of irradiation time. (author)

Use of details in secondary emission spectra in order to take into account element composition in the radioisotopic, x-ray-fluorescence method

Energy Technology Data Exchange (ETDEWEB)

Ivanyukovich, G A; Meier, V A; Nakhabtsev, V S

1974-01-01

A study is made of secondary emission spectra applicable to the conditions of determining tin in complex iron ores. Use is made of recorders having an intermediate target of samarium oxide, which assure measurement under geometry of a direct field of vision. It is shown that the integral count rate with a definite selection of the initial condition of discrimination or the count rate in the 32 to 34 keV interval of energies characterizes mainly the composition of the filler. With the purpose of increasing the accuracy and decreasing the effect of equipment factors it is more suitable to estimate the filler composition from the integral count rate. Methods are considered for taking into account the effect of composition of the medium on the measurement results according to the method of spectral ratios by means of a nomogram and analytical expressions. With measurements on models the error of determining the tin content was +- 5 percent in effective atomic number range of 13 to 20, while the error was 50 percent without the introduction of corrections. 10 refs. (tr-auth)

Radium-223 in treatment of castration-resistant prostate cancer with skeletal metastases

Directory of Open Access Journals (Sweden)

V. B. Matveev

2017-01-01

Full Text Available More than 90 % of patients with metastatic castration-resistant prostate cancer (CRPC have radiologically confirmed skeletal metastases. Traditional treatment methods such as administration of painkillers, external beam therapy, bisphosphonates or denosumab, as well as injections of strontium-89 or samarium-153 radionuclides, have only palliative effect and in some cases can postpone development of skeletal complications. Alpha-emitter radium-223 dichloride (Ra-223; alpharadin previously is currently one of the known drugs with proven effectiveness in relation to increasing overall survival of patients with CRPC. Ra-223 was developed specifically for patients with CRPC and symptomatic skeletal metastases. The drug targets the areas of skeletal tissue remodeling. Ra-223 is the therapy of choice in patients with CRPC and skeletal metastases and without confirmed visceral metastases before and after docetaxel chemotherapy. Chemotherapy after treatment with Ra-223 is a possible and satisfactory tolerable treatment option. Combination of Ra-223 with abiraterone, enzalutamide, or denosumab is, apparently, effective and safe, but further studies are necessary.

Analysis and separation of lanthanide elements

International Nuclear Information System (INIS)

Almeida Pimentel, E. de.

1973-01-01

Improvements of rare earth separation by the combined use of acetic and critic acid were studied and analytical methods for determining some of the lanthanides were tryed out. Separations of the R.E. studied were favorable when citric acid (solution A) and acetic acid (solution B) were used in the proportion of 10:1 at pH=4,00. Neutron activation, spectro-photometric, polarographic, volumetric and gravimetric procedures allowed the determination of 8 R.E.; samarium, neodymium, praseodymium, lanthanum, cerium, holmium, erbium and europium

Extraction with tributyl phosphate (TBP) from ferric nitrate solutions

International Nuclear Information System (INIS)

Kolarik, Z.; Grudpan, K.

1985-01-01

Ferric nitrate acts as a strong salting-out agent in the extraction of thorium(IV), uranyl, europium(III), samarium(III) and zirconium(IV) nitrates as well as of nitric acid with tributyl phosphate in dodecane. Nitric acid, if present in the extraction system together with large amounts of ferric nitrate, markedly suppresses the extraction of thorium(IV) and lanthanides(III) but significantly supports the extraction of zirconium(IV). Separation factors of different metal pairs are presented as functions of the concentrations of ferric nitrate and nitric acid

Geochronology Intermediary Laboratory implantation at the Rio Grande do Norte Federal University: the dating of the Serrinha Granitoid (RN) and the correlate Brasiliana extensional deformation; Implantacao do Laboratorio Intermediario de Geocronologia na UFRN: a datacao do granitoide de Serrinha (RN) e da deformacao extensional brasiliana correlata

Energy Technology Data Exchange (ETDEWEB)

Macedo, Maria Helena F.; Sa, Emanuel F. Jardim de; Souza, Zorano S. [Pernambuco Univ., Recife, PE (Brazil). Nucleo de Pesquisa em Geodinamica e Geofisica; Mendes, Franklin S. [Pernambuco Univ., Recife, PE (Brazil). Curso de Quimica; Ramalho, Karlos A.C. [Pernambuco Univ., Recife, PE (Brazil). Curso de Geologia

1997-12-31

The article describes the activities developed by the Geochronology Intermediary Laboratory at the Federal University of the Rio Grande do Norte, a Brazilian university, where there were the preoccupation of establishing strategies for a geochronological development. It relates the Rubidium-Strontium (Rb/Sr) and Samarium-Neodymium (Sm/Nd) methods, describing the analysis realized in these methodologies. Afterward, it presents the geological and petrographic situation of the Granitoide de Serrinha, located at Rio Grande do Norte State, Brazil and its geochronological data 8 refs., 2 figs.

Ab initio calculation of the migration free energy of oxygen diffusion in pure and samarium-doped ceria

Science.gov (United States)

Koettgen, Julius; Schmidt, Peter C.; Bučko, Tomáš; Martin, Manfred

2018-01-01

We have studied the free energy migration barriers Δ F‡ for oxygen diffusion in pure ceria and Sm-doped ceria for the temperatures 300, 700, and 1000 K. We used the density functional theory in the generalized gradient approximation and an additional Hubbard U parameter for the Ce 4 f electronic states. We compare the results for the free energy deduced from three different methods. First, a static harmonic approach is applied in which the temperature dependent vibrational contributions to energy and entropy are deduced from the phonon frequencies of supercells with a fixed volume. Second, a static quasiharmonic approach is used in which a part of the anharmonicity effect is introduced via an implicit dependence of the harmonic frequencies on the thermally expanding cell volume. Third, the free energy barriers are calculated using metadynamics and molecular dynamics in which anharmonicity effects are naturally taken into account. The three methods examined in this study lead to distinctly different results. According to the harmonic approximation, the migration free energy difference Δ F‡ increases with increasing temperature due to an increasing entropic contribution. According to the quasiharmonic approximation, the migration free energy is independent of temperature. Finally, molecular dynamics predicts a thermally induced increase in the migration free energy. We conclude that temperature dependent experimental lattice constants cancel out the increasing entropic contribution with increasing temperature in the static quasiharmonic approach. The full consideration of anharmonicity effects in the metadynamics method again leads to a temperature dependent migration free energy.

The effect of phase assemblages, grain boundaries and domain structure on the local switching behavior of rare-earth modified bismuth ferrite ceramics

International Nuclear Information System (INIS)

Alikin, Denis O.; Turygin, Anton P.; Walker, Julian; Bencan, Andreja; Malic, Barbara; Rojac, Tadej; Shur, Vladimir Ya.; Kholkin, Andrei L.

2017-01-01

Piezoelectric properties and ferroelectric/ferroelastic domain switching behavior of polycrystalline ceramics are strongly influenced by local scale (i.e. <100 nm) phenomena, such as, the phase assemblages, domain structure, and defects. The method of ceramic synthesis strongly effects the local properties and thus plays a critical role in determining the macroscopic ferroelectric and piezoelectric performance. The link between synthesis and local scale properties of ferroelectrics is, however, rarely reported, especially for the emerging lead-free materials systems. In this work, we focus on samarium modified bismuth ferrite ceramics (Bi_0_._8_8Sm_0_._1_2FeO_3, BSFO) prepared by two methods: standard solid state reaction (SSR) and mechanochemi≿ally assisted synthesis (MAS). Each ceramic possesses different properties at the local scale and we used the piezoresponse force microscopy (PFM) complemented by transmission electron microscopy (TEM) to evaluate phase distribution, domain structure and polarization switching to show that an increase in the anti-polar phase assemblages within the polar matrix leads to notable changes in the local polarization switching. SSR ceramics exhibit larger internal bias fields relative to the MAS ceramics, and the grain boundaries produce a stronger effect on the local switching response. MAS ceramics were able to nucleate domains at lower electric-fields and grow them at faster rates, reaching larger final domain sizes than the SSR ceramics. Local evidence of the electric-field induced phase transition from the anti-ferroelectric Pbam to ferroelectric R3c phase was observed together with likely evidence of the existence of head-to-head/tail-to-tail charged domain walls and domain vortex core structures. By comparing the domain structure and local switching behavior of ceramics prepared by two different methods this work brings new insights the synthesis-structure-property relationship in lead-free piezoceramics.

Formation and characterization of samarium oxide generated from different precursors

International Nuclear Information System (INIS)

Hussein, G.A.M.; Buttrey, D.J.; DeSanto, P.; Abd-Elgaber, A.A.; Roshdy, Heba; Myhoub, Ali Y.Z.

2003-01-01

Sm(NO 3 ) 3 ·6H 2 O and Sm 2 (C 2 O 4 ) 3 ·10H 2 O were used as precursors for the formation of Sm 2 O 3 . Thermal processes involved in the decomposition course of both salts up to 800 deg. C in air were monitored by nonisothermal gravimetry and differential thermal analysis. Intermediates and final solid products were characterized by IR-spectroscopy, X-ray diffraction and scanning electron microscopy. The results showed that Sm(NO 3 ) 3 ·6H 2 O decomposes completely through nine endothermic mass loss processes. The dehydration occurs through the first four steps at 90, 125, 195, and 240 deg. C, culminating in a crystalline nitrate monohydrate, which subsequently decomposes to Sm(OH)(NO 3 ) 2 at 355 deg. C. The latter decomposes rapidly to form a stable and crystalline SmO(NO 3 ) at 460 deg. C, through nonstoichoimetric unstable intermediates. Finally Sm 2 O 3 forms at 520 deg. C. For the oxalate, the dehydration occurs in five steps: the anhydrous oxalate is thermally unstable and immediately decomposes to Sm 2 O 3 at 645 deg. C through two unstable intermediates. The crystalline oxide obtained from the nitrate contains larger pores than the oxide obtained from the oxalate, as indicated from scanning electron microscopy (SEM) results

Influence of Samarium on Learning and Memory Function of Rats

Institute of Scientific and Technical Information of China (English)

无

2006-01-01

Sixty-four Spraque-Dawley(SD)big rats with weaning weight of (195±15) g were randomly divided into 4 groups with 8 males and 8 females each group. One group drunk with de-ionized water served as control and was also used for analysis of the background. The other three groups rats were raised by de-ionized water containing low, middle and high concentrations of Sm for four months, then learning and memory tests were carried out in Y-electric maze. Compared with the control rats, the learning and memory of rats in low and middle groups shows a deterioration trend, exhibiting the function degradation of rats' brain. It may results from the rare earth elements through blood-brain barrier affecting the normal physiological functions of rats' brain. In addition, the activity of superoxide dismutase (SOD) in rats' brain decreases, while the content of malondialdehyde (MDA) concentration increases. The decreased SOD activity and the increased MDA mean the degeneration the ability of anti-oxidation in rats' brain, which are accordance with the degradation of learning and memory function of rats in low and middle Sm groups.

Oriented growth of thin films of samarium oxide by MOCVD

Indian Academy of Sciences (India)

Unknown

Very thin layers of rare earth oxides, such as Sm2O3 and epitaxial Gd2O3, grown by thermal ... As the inorganic salts of the lanthanides, such as their halides, are ... sodium hydroxide, followed by the addition of ethanolic. 1,10-phenanthroline ...

Spectroscopy of samarium isotopes in the sdg interacting boson model

International Nuclear Information System (INIS)

Devi, Y.D.; Kota, V.K.B.

1992-01-01

Successful spectroscopic calculations for the 0 1 + , 2 1 + , and 4 1 + levels in 146-158 Sm are carried out in sdg boson space with the restriction that the s-boson number n s ≥2 and the g-boson number n g ≤2. Observed energies, quadrupole and magnetic moments, E2 and E4 transition strengths, nuclear radii, and two-nucleon transfer intensities are reproduced with a simple two-parameter Hamiltonian. For a good simultaneous description of ground, β, and γ bands, a Hamiltonian interpolating the dynamical symmetries in the sdg model is employed. Using the resulting wave functions, in 152,154 Sm, the observed B(E4;0 1 + →4 γ + ) values are well reproduced and E4 strength distributions are predicted. Moreover, a particular ratio scrR involving two-nucleon transfer strengths showing a peak at neutron number 90 is well described by the calculations

Isotopic Ratios of Samarium by TIMS for Nuclear Forensic Application

Energy Technology Data Exchange (ETDEWEB)

Louis Jean, James [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Inglis, Jeremy David [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-08

The isotopic ratio of Nd, Sm, and Gd can provide important information regarding fissile material (nuclear devices, reactors), neutron environment, and device yield. These studies require precise measurement of Sm isotope ratios, by either TIMS or MC-ICP-MS. There has been an increasing trend to measure smaller and smaller quantities of Sm bearing samples. In nuclear forensics 10-100 ng of Sm are needed for precise measurement. To measure sub-ng Sm samples using TIMS for nuclear forensic analysis.

Subcoulomb fusion of 16O in odd Sm isotopes

International Nuclear Information System (INIS)

Pacheco, A.J.

1989-01-01

Cross sections for the formation of evaporation residues were measured for the reaction of 16 O with the odd 147 Sm and 149 Sm nuclei at near barrier energies. The results are well described by statistical model calculations. Fusion cross sections as a function of energy do not show any unusual behaviour that could be attributed to the presence of unpaired nucleons. An analysis based on a one-dimensional penetration model that includes the effect of permanent quadrupolar deformations shows that the extracted values of the parameter β 2 follow the systematics established by the rest of the even samarium isotopes. The dependence of β 2 on the mass of the target nucleus indicates that the influence exerted by collective aspects upon the subbarrier fusion process increases rapidly as a function of the number of neutrons added to the spherical semimagic 144 Sm nucleus. (Author) [es

Testing of the level density segment of the RIPL

International Nuclear Information System (INIS)

Capote, Roberto

2000-01-01

A comparison between RIPL phenomenological state density parameterizations and microscopical state density (SD) codes was performed for nickel and samarium isotopes. All the codes were shown to be complete. More work is needed on calculation of the collective enhancement of the level densities to improve currently used phenomenological recipes. It was shown that phenomenological closed formulae for particle-hole state density fails to describe microscopical calculation for magic nuclei. For deformed nuclei, like Sm-152, the agreement of Williams closed formulae considering Kalbach pairing correction with microscopical SID calculations was very good. (author)

Spectrographic Determination of Trace Constituents in Rare Earths

International Nuclear Information System (INIS)

Capdevila, C.; Alvarez, F.

1962-01-01

A spectrographic method was developed for the determination of 18 trace elements in lanthanum, cerium, praseodimium, neodimium and samarium compounds. The concentrations of the impurities cover the range of 0,5 to 500 ppm. Most of these impurities are determined by the carrier distillation method. Several more refractory elements have been determined by total burning of the sample with a direct current arc or by the conduction briquet excitation technique with a high voltage condensed spark. The work has been carried out with a Hilger Automatic Large Quartz Spectrograph. (Author) 5 refs

Synthesis and physicochemical analysis of Sm (II, III) acetylacetone chelate complexes

International Nuclear Information System (INIS)

Kostyuk, N.N.; Dik, T.A.; Trebnikov, A.G.

2004-01-01

Sm (II, III) acetylacetone chelate complexes were synthesized by electrochemical method. It was shown that anode dissolution of the metal samarium over acetylacetone leads to formation of the Sm (II, III) chelate complexes: xSm(acac)2 · ySm(acac)3 · zH(acac). Factors x, y and z depend on quantity of the electricity, which flew through the electrolysis cell. The compositions of the obtained substances were confirmed by the physicochemical analysis (ultimate analysis, IR-, mass spectroscopy and thermal analysis (thermogravimetric, isothermal warming-up and differential scanning colorimetry). (Authors)

Synthesis and application of a new fluorous-tagged ammonia equivalent

DEFF Research Database (Denmark)

Nielsen, Simon Dalsgaard; Smith, Garrick; Begtrup, Mikael

2010-01-01

A novel fluorous-tagged ammonia equivalent has been developed. It is based on a nitrogen-oxygen bond, which can be cleaved in a traceless manner by a molybdenum complex or samarium diiodide. The application in the synthesis of ureas, amides, sulfonamides, and carbamates is described. The scope of...... of the fluorous N--O linker is exemplified by the synthesis of itopride, a drug used for the treatment of functional dyspepsia. Itopride was synthesized with the aid of fluorous purification methods and the product was isolated in good overall yield, with high purity....

Short-wavelength soft-x-ray laser pumped in double-pulse single-beam non-normal incidence

International Nuclear Information System (INIS)

Zimmer, D.; Ros, D.; Guilbaud, O.; Habib, J.; Kazamias, S.; Zielbauer, B.; Bagnoud, V.; Ecker, B.; Aurand, B.; Kuehl, T.; Hochhaus, D. C.; Neumayer, P.

2010-01-01

We demonstrated a 7.36 nm Ni-like samarium soft-x-ray laser, pumped by 36 J of a neodymium:glass chirped-pulse amplification laser. Double-pulse single-beam non-normal-incidence pumping was applied for efficient soft-x-ray laser generation. In this case, the applied technique included a single-optic focusing geometry for large beam diameters, a single-pass grating compressor, traveling-wave tuning capability, and an optimized high-energy laser double pulse. This scheme has the potential for even shorter-wavelength soft-x-ray laser pumping.

Neutron activation analysis of the rare earth elements in Nasu hot springs

International Nuclear Information System (INIS)

Ikeda, Nagao; Takahashi, Naruto.

1978-01-01

Eleven rare earth elements (lanthanum, cerium, neodymium, samarium, europium, gadolinium, terbium, holmium, thulium, ytterbium and lutetium) in hot spring waters and sinter deposits in the Nasu area were determined by the neutron activation method. The rare earth elements in hot spring water were preconcentrated in ferric hydroxide precipitate and neutron-irradiated. The rare earth elements were chemically separated into lighter and heavier groups and the activity of each group was measured with a Ge(Li) detector. Distribution of the rare earth elements between the hot spring water and the sinter deposit was also discussed. (auth.)

Sm 3+-doped polymer optical waveguide amplifiers

Science.gov (United States)

Huang, Lihui; Tsang, Kwokchu; Pun, Edwin Yue-Bun; Xu, Shiqing

2010-04-01

Trivalent samarium ion (Sm 3+) doped SU8 polymer materials were synthesized and characterized. Intense red emission at 645 nm was observed under UV laser light excitation. Spectroscopic investigations show that the doped materials are suitable for realizing planar optical waveguide amplifiers. About 100 μm wide multimode Sm 3+-doped SU8 channel waveguides were fabricated using a simple UV exposure process. At 250 mW, 351 nm UV pump power, a signal enhancement of ˜7.4 dB at 645 nm was obtained for a 15 mm long channel waveguide.

Potentiometric studies on some ternary complexes of Nd(III), Sm(III), Gd(III) and Ho(III) with cyclohexanediaminetetraacetic acid as primary ligand

International Nuclear Information System (INIS)

Marathe, D.G.; Munshi, K.N.

1983-01-01

The formation constants of the ternary complexes of neodymium(III), samarium(III), gadlonium(III) and holmium(III) with cyclohexanediaminetetraacetic acid (CyDTA) as primary ligand and dihydroxynaphthalene (DHN), dihydroxynaphthalene-6-sulphonic acid (DHNSA) and cateechol-3,5-disulphonic acid (CDSA) as secondary ligands have been investigated by potentiometric titration technique. The secondary ligands have been investigated by potentiometric titration technique. The values of formation constants of 1:1:1 ternary chelates are reported at three different temperatures, and at a fixed ionic strength, μ = 0.1 M (NaClO 4 ). (author)

Time-resolved fluoroimmunoassay of phytoviruses by monoclonal antibodies. Vremenno-razreshennyj fluoroimmunoanaliz fitovirusos pri pomoshchi monoklonal'nykh antitel

Energy Technology Data Exchange (ETDEWEB)

Saarma, M Yu; Yarvekyul' g, L V; Andreeva, E G; Siniyarv, R K

1989-01-01

Monoclonal antibodies (MAbs) to potato viruses were labelled with lanthanides and used for time-resolved fluoroimmunoassay (TRFIA) of these viruses. TRFIA of potato leafroll virus (PLRV) had the sensitivity less than 1 ng/ml and was therefore approx 10 times more sensitive than ELISA. Possibility of simultaneous quantitative detection of several viruses by different MAbs labelled with europium, samarium and terbium provides TRFIA of fundamental advantage. Data on simultaneous sensitive detection of two viruses - PLRV and PVX (0,5 ng/ml of both) and three viruses - PLRV, PVX and PVM are given.

Luminosity enhancements at SLAC

International Nuclear Information System (INIS)

Coward, D.H.

1984-04-01

Several ideas are discussed that have been proposed to improve the luminosity at the SPEAR and PEP electron-positron storage rings and to insure good luminosity at the SLAC Linear Collider. There have been two proposals studied recently for SPEAR: a Microbeta insertion using Samarium Cobalt permanent magnets, and a Minibeta insertion using conventional quadrupole magnets. The notations Microbeta and minibeta used here are somewhat arbitrary since the front faces of the first quadrupole magnets for both insertions are at nearly the same distance from the interaction point

Nuclear deformation in the configuration-interaction shell model

Science.gov (United States)

Alhassid, Y.; Bertsch, G. F.; Gilbreth, C. N.; Mustonen, M. T.

2018-02-01

We review a method that we recently introduced to calculate the finite-temperature distribution of the axial quadrupole operator in the laboratory frame using the auxiliary-field Monte Carlo technique in the framework of the configuration-interaction shell model. We also discuss recent work to determine the probability distribution of the quadrupole shape tensor as a function of intrinsic deformation β,γ by expanding its logarithm in quadrupole invariants. We demonstrate our method for an isotope chain of samarium nuclei whose ground states describe a crossover from spherical to deformed shapes.

Spectrographic Determination of Trace Constituents in Rare Earths; Determinacion espectrografica de impurezas en tierras raras

Energy Technology Data Exchange (ETDEWEB)

Capdevila, C; Alvarez, F

1962-07-01

A spectrographic method was developed for the determination of 18 trace elements in lanthanum, cerium, praseodimium, neodimium and samarium compounds. The concentrations of the impurities cover the range of 0,5 to 500 ppm. Most of these impurities are determined by the carrier distillation method. Several more refractory elements have been determined by total burning of the sample with a direct current arc or by the conduction briquet excitation technique with a high voltage condensed spark. The work has been carried out with a Hilger Automatic Large Quartz Spectrograph. (Author) 5 refs.

Geochronology and structuring of the Ceara State: Borborema Province northwestern part, NE Brazil

International Nuclear Information System (INIS)

Fetter, A.; Van Schmus, W.R.; Santos, Ticiano J. Saraiva dos; Arthaud, M.; Nogueira Neto, J.

1997-01-01

The work confirms that the geochronological new data U/Pb in zircon and Samarium/Neodymium from the Ceara State furnished a refined chronology of the geological activity in the NW part of the Borborema Province, indicating an evolutive history since 2,78 Ga and 532 Ma. Furthermore, these data facilitated the different crust domain outlines in the region, putting age maximum limits in the pre-brasilianas supracrusts rocks deposition, and evidencing the epoch and duration of the Brasiliano magmatism and metamorphism in the northwest part of the State

The trial of obtaining a high-grade gadolinium concentrate using the fractional precipitation together with the ion exchange

International Nuclear Information System (INIS)

Ozga, W.; Soltysiak, I.

1980-01-01

The modified fractional precipitation of lanthanon-potassium double chromate was used for preliminary separation of gadolinium concentrate containing 60% Gd 2 O 3 , 33,3% Sm 2 O 3 . The 1-st fraction enriched with samarium (60% Sm 2 O 3 ) and 2-nd fraction enriched with gadolinium (80% Gd 2 O 3 with efficiency of 82% recounting on Gd 2 O 3 ) were obtained. Both fractions were separated by the elution with EDTA solution buffered with ammonium acetate. The good results were obtained by ion exchange separation only of the 1-st fraction. (author)

Fluorescence enhancement of samarium complex co-doped with terbium complex in a poly(methyl methacrylate) matrix

International Nuclear Information System (INIS)

Jiu Hongfang; Zhang Lixin; Liu Guode; Fan Tao

2009-01-01

The fluorescence property of Sm(DBM) 3 phen- (DBM-dibenzoylmethide, phen-1,10-phenanthroline) and Tb(DBM) 3 phen-co-doped poly(methyl methacrylate) (PMMA) was investigated. The excitation, emission spectra and fluorescence lifetime of the co-doped samples were examined. In the co-doped samples, the luminescence intensities of Sm 3+ enhance with an increase of the Tb(DBM) 3 phen content and with a decrease of the Sm(DBM) 3 phen content. The reason for the fluorescence enhancement effect in the co-doped polymer is the intermolecular energy transfer. To give a vivid picture for this co-doped system, a model for the fluorescence enhancement of Sm(DBM) 3 phen- and Tb(DBM) 3 phen-co-doped PMMA is presented

Adjustable permanent quadrupoles for the next linear collider

International Nuclear Information System (INIS)

Volk, James T.

2001-01-01

The proposed Next Linear Collider (NLC) will require over 1400 adjustable quadrupoles between the main linacs' accelerator structures. These 12.7 mm bore quadrupoles will have a range of integrated strength from 0.6 to 138 Tesla, with a maximum gradient of 141 Tesla per meter, an adjustment range of +0 to -20% and effective lengths from 324 mm to 972 mm. The magnetic center must remain stable to within 1 micron during the 20% adjustment. In an effort to reduce costs and increase reliability, several designs using hybrid permanent magnets have been developed. Four different prototypes have been built. All magnets have iron poles and use Samarium Cobalt to provide the magnetic fields. Two use rotating permanent magnetic material to vary the gradient, one uses a sliding shunt to vary the gradient and the fourth uses counter rotating magnets. Preliminary data on gradient strength, temperature stability, and magnetic center position stability are presented. These data are compared to an equivalent electromagnetic prototype

Adjustable Permanent Quadrupoles for the Next Linear Collider

International Nuclear Information System (INIS)

Spencer, Cherrill M

2001-01-01

The proposed Next Linear Collider (NLC) will require over 1400 adjustable quadrupoles between the main linacs' accelerator structures. These 12.7 mm bore quadrupoles will have a range of integrated strength from 0.6 to 138 Tesla, with a maximum gradient of 141 Tesla per meter, an adjustment range of +0 to - 20% and effective lengths from 324 mm to 972 mm. The magnetic center must remain stable to within 1 micron during the 20% adjustment. In an effort to reduce costs and increase reliability, several designs using hybrid permanent magnets have been developed. Four different prototypes have been built. All magnets have iron poles and use Samarium Cobalt to provide the magnetic fields. Two use rotating permanent magnetic material to vary the gradient, one uses a sliding shunt to vary the gradient and the fourth uses counter rotating magnets. Preliminary data on gradient strength, temperature stability, and magnetic center position stability are presented. These data are compared to an equivalent electromagnetic prototype

Adjustable Permanent Quadrupoles Using Rotating Magnet Material Rods for the Next Linear Collider.

CERN Document Server

Spencer, C M

2002-01-01

The proposed Next Linear Collider (NLC) will require over 1400 adjustable quadrupoles between the main linacs' accelerator structures. These 12.7 mm bore quadrupoles will have a range of integrated strength from 0.6 to 132 Tesla, with a maximum gradient of 135 Tesla per meter, an adjustment range of +0 -20% and effective lengths from 324 mm to 972 mm. The magnetic center must remain stable to within 1 micrometer during the 20% adjustment. In an effort to reduce estimated costs and increase reliability, several designs using hybrid permanent magnets have been developed. All magnets have iron poles and use either Samarium Cobalt or Neodymium Iron to provide the magnetic fields. Two prototypes use rotating rods containing permanent magnetic material to vary the gradient. Gradient changes of 20% and center shifts of less than 20 microns have been measured. These data are compared to an equivalent electromagnet prototype. See High Reliability Prototype Quadrupole for the Next Linear Collider by C.E Rago, C.M SPENC...

Thermodynamic and electrochemical properties of some rare earth cryptates and related complexes in propylene carbonate

International Nuclear Information System (INIS)

Loufouilou, E.L.

1986-03-01

The stability of trivalent lanthanide complexes with [1]-cryptand 22 and [2]-cryptands 222 and 211 and also tris (3.6- dioxa heptyl) amine (TDHA) is studied in propylene carbonate solution by potentiometry with Ag + as an auxiliary cation. Complexation enthalpies and entropies are determined for other complexes of some trivalent lanthanides (La, Er, Pr and Eu) with ligands 222, 221, 211, 22, 21, 18C6 and TDHA. [1]- and [2]- crytands are complexing agents more powerful than TDHA and crown-ethers 15C6 and 18C6. For ligands containing nitrogen complexe stability increase with RE atomic number but decrease for crown-ethers. In propylene carbonate complexes are stabilized by enthalpic effects, entropic contribution is variable. Polarographic reduction of samarium cryptate with ligand 222, 221 and 22 in propylene carbonate is reversible as in more solvating solvents water and methanol. Mixed complexes are formed with chlorides and this cryptate system is more difficult to reduce [fr

HF propagation results from the Metal Oxide Space Cloud (MOSC) experiment

Science.gov (United States)

Joshi, Dev; Groves, Keith M.; McNeil, William; Carrano, Charles; Caton, Ronald G.; Parris, Richard T.; Pederson, Todd R.; Cannon, Paul S.; Angling, Matthew; Jackson-Booth, Natasha

2017-06-01

With support from the NASA sounding rocket program, the Air Force Research Laboratory launched two sounding rockets in the Kwajalein Atoll, Marshall Islands in May 2013 known as the Metal Oxide Space Cloud experiment. The rockets released samarium metal vapor at preselected altitudes in the lower F region that ionized forming a plasma cloud. Data from Advanced Research Project Agency Long-range Tracking and Identification Radar incoherent scatter radar and high-frequency (HF) radio links have been analyzed to understand the impacts of the artificial ionization on radio wave propagation. The HF radio wave ray-tracing toolbox PHaRLAP along with ionospheric models constrained by electron density profiles measured with the ALTAIR radar have been used to successfully model the effects of the cloud on HF propagation. Up to three new propagation paths were created by the artificial plasma injections. Observations and modeling confirm that the small amounts of ionized material injected in the lower F region resulted in significant changes to the natural HF propagation environment.

Ultrasound assisted sonochemical synthesis of samarium doped Y2O3 nanostructures for display applications

Science.gov (United States)

Venkatachalaiah, K. N.; Nagabhushana, H.; Basavaraj, R. B.; Venkataravanappa, M.; Suresh, C.

2018-04-01

Sm3+ doped (1-11 mol %) cubic Y2O3 nanoflowers were fabricated by simple low temperature Sonochemical method using Aloe Vera gel as fuel. The product was characterized by PXRD, SEM, TEM, DRS, PL etc. The powder X-ray diffraction (PXRD) profiles of nanophosphors showed cubic phase structure. The particle size was further confirmed by transmission electron microscope (TEM) and it was found to be in the range of 17-25 nm. The PL emission results reveal that the phosphor nanoparticles (NPs) emit an intensive yellowish light under 367 nm excitation. The excitation spectrum of Y2O3: Sm3+ (5 mol %) obtained by monitoring the emission of the 4f - 4f (4G5/2→6H7/2) transition of Sm3+ at 612 nm As can be seen that the excitation spectrum consists of strong band at 332 nm and a broad band centered at 367 nm which corresponds to host absorption, confirming the effective energy transfer from Y2O3 host to Sm3+ ions. In the present study, CIE and CCT were estimated and found to be (0.45688, 0.51727) and the CCT of Y2O3: Sm3+ at 367 nm excitation was found to be 3357 K which was within the range of vertical daylight. Thus it can be useful for artificial production of illumination devices.

Preparation And Biodistribution Study Of 153sm-Albumin Microspheres As Radiosynovectomy Agent

International Nuclear Information System (INIS)

W, Widyatuti; Tamat, Swasono R.; Indrawati, Teti; Fatimah; Aulya, Anna

2003-01-01

Treatment of rheumatics arthritis previously was done by inflamed synovial membrane surgery called synovectomy. The conventional synovectomy was costly and inconvenient method for the patients, therefore alternative method using radiation synovectomy was considered. Preparation of 153 Sm albumin microspheres as radio synovectomy agent has been candied out. Experiments have been carried out to decide optimal conditions of preparation, such as speed and time of stirring to form microspheres, and to find optimal condition in labelling the microspheres, such as pH, content of sodium citrate, samarium oxide and the amount of microspheres. The albumin particles were expected as spheres with 15-50 μm in diameter, high labelling efficiency and 153 Sm is strongly bound to the microspheres. In-vitro and in-vivo stability were tested by observing 153 Sm released from the particles after incubating the labelled particles in saline and human serum albumin solution for one week, and after administration of labelled particles into Wistar rats via intraarticular injection through one of its knee joint. The result shows the optimal speed and time of stirring to obtain desired shape and size of the particles was 750 rpm in 15 minutes, while the optimal formulation to obtain high labelling efficiency was at pH 5-6, containing 10 μg/mL of sodium citrate, 125 μg/mL of samarium oxide and 10 mg of albumin microspheres. The preparation was stable up to 5 days. In conclusion the 153 Sm-albumin microspheres can be produced and is ready for clinical trial

Uptake and Effects of Six Rare Earth Elements (REEs on Selected Native and Crop Species Growing in Contaminated Soils.

Directory of Open Access Journals (Sweden)

David Carpenter

Full Text Available Rare earth elements (REEs have become increasingly important metals used in modern technology. Processes including mining, oil refining, discarding of obsolete equipment containing REEs, and the use of REE-containing phosphate fertilizers may increase the likelihood of environmental contamination. However, there is a scarcity of information on the toxicity and accumulation of these metals to terrestrial primary producers in contaminated soils. The objective of this work was to assess the phytotoxicity and uptake from contaminated soil of six REEs (chloride forms of praseodymium, neodymium, samarium, terbium, dysprosium, and erbium on three native plants (Asclepias syriaca L., Desmodium canadense (L. DC., Panicum virgatum L. and two crop species (Raphanus sativus L., Solanum lycopersicum L. in separate dose-response experiments under growth chamber conditions. Limited effects of REEs were found on seed germination and speed of germination. Effects on aboveground and belowground biomass were more pronounced, especially for the three native species, which were always more sensitive than the crop species tested. Inhibition concentrations (IC25 and IC50 causing 25 or 50% reductions in plant biomass respectively, were measured. For the native species, the majority of aboveground biomass IC25s (11 out of 18 fell within 100 to 300 mg REE/kg dry soil. In comparison to the native species, IC25s for the crops were always greater than 400 mg REE/kg, with the majority of results (seven out of 12 falling above 700 mg REE/kg. IC50s were often not detected for the crops. Root biomass of native species was also affected at lower doses than in crops. REE uptake by plants was higher in the belowground parts than in the above-ground plant tissues. Results also revealed that chloride may have contributed to the sensitivity of the native species, Desmodium canadense, one of the most sensitive species studied. Nevertheless, these results demonstrated that

Non-destructive testing of assemblies by welding, brazing or bonding, and material to use for this process

International Nuclear Information System (INIS)

Benoit, J.

1983-01-01

The process consists in doing a neutron photography of the pieces assembled with the aid of a joining material containing a neutrophage element, such as gadolinium, samarium, europium, boron, cadmium. The neutrophage element, e.g. gadolinium, is dispersed in the joining material with contents between 0,5 and 7,5% of weight. Its granulometry must be less than 1000 MESH. The incorporation of a neutrophage element in the joining material of metallic pieces by welding or brazing, allows to visualize, among others, the following defects: blistering, cracks, slag inclusions, undercuts, bad distribution of the successive passes [fr

Synthesis and application of a new fluorous-tagged ammonia equivalent.

Science.gov (United States)

Nielsen, Simon D; Smith, Garrick; Begtrup, Mikael; Kristensen, Jesper L

2010-04-19

A novel fluorous-tagged ammonia equivalent has been developed. It is based on a nitrogen-oxygen bond, which can be cleaved in a traceless manner by a molybdenum complex or samarium diiodide. The application in the synthesis of ureas, amides, sulfonamides, and carbamates is described. The scope of the fluorous N-O linker is exemplified by the synthesis of itopride, a drug used for the treatment of functional dyspepsia. Itopride was synthesized with the aid of fluorous purification methods and the product was isolated in good overall yield, with high purity. Copyright © 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Synthesis, characterization and reactivity of some lanthanide organometallics

International Nuclear Information System (INIS)

Marchal, N.

1991-12-01

Organo lanthanides with reactive metal-carbon bonds are obtained by direct synthesis of the metal (powder) and a hydrocarbon in ether medium, like with alkali metals. Two types of synthesis are envisaged: formation of covalent bonds by opening cycles, only biphenylene is reactive enough in regard to ytterbium and samarium, these organometallic compounds can also be prepared by the classical way, i.e. reaction of 2.2'-dilithio biphenyl on rare earth halogenides and coupling of 6.6-dimethylfulvene leading to dicyclopentadienyl compounds with Sm and Yb. The reactivity of these complexes is studied by catalysis of ethylene polymerization

Knudsen cell vaporization of rare earth nitrides: enthalpy of vaporization of HoN098

International Nuclear Information System (INIS)

Brown, R.C.; Clark, N.J.

1975-01-01

The enthalpy of vaporization of HoN 0 . 98 was measured by the weight-loss Knudsen cell technique using Motzfeldt-Whitman extrapolations to zero orifice area. A third-law enthalpy of vaporization of HoN 0 . 98 of 155.9 +- 5 kcal mole -1 was obtained compared to a second-law value of 162.0 +- 5 kcal mole -1 . Similar measurements on the nitrides of samarium, erbium, and ytterbium gave third-law enthalpies of vaporization of 126.8 +-- 5 kcal mole -1 ; 159.6 +- 5 kcal mole -1 , and 121.0 +- 5 kcal mole -1 , respectively. 7 tables

5 nm structures produced by direct laser writing

International Nuclear Information System (INIS)

Pavel, E; Jinga, S; Andronescu, E; Vasile, B S; Rotiu, E; Ionescu, L; Mazilu, C

2011-01-01

Here we present a new approach to overcome the optical diffraction limit by using novel materials. In the paper, we report experimental results obtained by high-resolution transmission electron microscopy (HRTEM) and optical absorption spectroscopy, for a fluorescent photosensitive glass-ceramic containing rare-earth ions such as samarium (Sm). Using a home built dynamic tester, with a low power laser, we recorded nanostructures having 5 nm line widths. In the line structure, measurements reveal the presence of silver nanocrystals with few nanometre sizes. HRTEM shows that there is a random orientation of the nanocrystals. A writing mechanism with three steps is proposed.

Voltage color tunable OLED with (Sm,Eu)-β-diketonate complex blend

Science.gov (United States)

Reyes, R.; Cremona, M.; Teotonio, E. E. S.; Brito, H. F.; Malta, O. L.

2004-09-01

Light emission from organic electroluminescent diodes (OLEDs) in which mixed samarium and europium β-diketonate complexes, [Sm 0.7Eu 0.3(TTA) 3(TPPO) 2], was used as the emitting layer is described. The electroluminescence spectra exhibit narrow peaks arising from 4f-intraconfigurational transitions of the Sm 3+ and Eu 3+ ions and a broad emission band attributed to the electrophosphorescence of the TTA ligand. The intensity ratio of the peaks determined by the bias voltage applied to the OLED, together with the ligand electrophosphorescence, allows to obtain a voltage-tunable color light source.

Prominent spectral features of Sm3+ ion in disordered zinc tellurite glass

Directory of Open Access Journals (Sweden)

Y.A. Tanko

Full Text Available Trivalent rare earth doped glasses with modified spectroscopic features are essential for solid state lasers and diverse photonic applications. Glass composition optimisation may fulfil such demand. Stimulating the spectral properties of samarium (Sm3+ ions in tellurite glass host with desired enhancement is the key issue. Glasses with composition (80 − xTeO2–20ZnO–(xSm2O3, where 0 ⩽ x ⩽ 1.5 mol% are prepared using melt quenching method. The role of varying Sm3+ contents to improving the absorption and emission properties of the prepared glasses are determined. XRD pattern verifies amorphous nature of synthesised glasses. FTIR spectroscopy has been used to observe the structural modification of (TeO4 trigonal bipyramid structural units. DTA traces display prominent transition peaks for glass transition, crystallisation and melting temperature. Samples are discerned to be stable with desired Hruby parameter and superior glass forming ability. The UV–Vis–NIR absorption spectra reveals nine peaks centred at 470, 548, 947, 1085, 1238, 1385, 1492, 1550 and 1589 nm. These bands arise due to 6H5/2 → 4I11/2, 4G5/2, 6F11/2, 6F9/2, 6F7/2, 6F5/2, 6F3/2, 6H15/2 and 6F1/2 transitions, respectively. The direct, indirect band gap and Urbach energy calculated from the absorption edge of UV–Vis–NIR spectra are found to appear within (2.75–3.18 eV, (3.22–3.40 eV, and (0.20–0.31 eV, respectively. The observed increase in refractive index from 2.45 to 2.47 is ascribed to the generation of non-bridging oxygen atoms via the conversion of TeO4 into TeO3 units. Conversely the decrease in refractive index to 2.39 is attributed to the lower ionic radii (1.079 Å of Sm3+. PL spectra under the excitation of 452 nm display four emission bands centred at 563, 600, 644 and 705 nm corresponding to 4G5/2 → 6H5/2, 6H7/2, 6H9/2 and 6H11/2 transitions of samarium ions. Excellent features of the results nominate these compositions

One-step synthesis of samarium-doped ceria and its CO catalysis

Indian Academy of Sciences (India)

Administrator

Key Laboratory for Special Functional Aggregate Materials of Education Ministry,. School of Chemistry ... increases the carbon-tolerance ability of the electrodes.6. All these properties .... which are comparable to the values of the (200) plane.

Experimental determination of anomalous scattering lengths of samarium for thermal neutrons

International Nuclear Information System (INIS)

Engel, D.W.; Koetzle, T.F.

1981-01-01

Anomalous scattering lengths of natural Sm for thermal neutrons with wavelengths between 0.827 and 1.300 A have been determined using a single crysrtal of a Sm-complex of known structure. 140 selected reflections were measured at each wavelength and b 0 + b' and b'' refined in each case. The values obtained are in good agreement with theoretical values obtained from a Breit-Wigner calculation using tabulated resonance parameters for 149 Sm. A value of b 0 = 4.3 +- 0.2 fm is deduced from the diffraction experiment

Grain size effect on Sr and Nd isotopic compositions in eolian dust. Implications for tracing dust provenance and Nd model age

International Nuclear Information System (INIS)

Feng Jinliang; Zhu Liping; Zhen Xiaolin; Hu Zhaoguo

2009-01-01

Strontium (Sr) and neodymium (Nd) isotopic compositions enable identification of dust sources and reconstruction of atmospheric dispersal pathways. The Sr and Nd isotopic compositions in eolian dust change systematically with grain size in ways not yet fully understood. This study demonstrates the grain size effect on the Sr and Nd isotopic compositions in loess and 2006 dust fall, based on analyses of seven separated grain size fractions. The analytical results indicate that Sr isotopic ratios strongly depend on the grain size fractions in samples from all types of eolian dust. In contrast, the Nd isotopic ratios exhibit little variation in loess, although they vary significantly with grain size in samples from a 2006 dust fall. Furthermore, Nd model ages tend to increase with increasing grain size in samples from all types of eolian dust. Comparatively, Sr isotopic compositions exhibit high sensitively to wind sorting, while Nd isotopic compositions show greater sensitively to dust origin. The principal cause for the different patterns of Sr and Nd isotopic composition variability with grain size appears related to the different geochemical behaviors between rubidium (Rb) and Sr, and the similar geochemical behaviors between samarium (Sm) and Nd. The Nd isotope data indicate that the various grain size fractions in loess have similar origins for each sample. In contrast, various provenance components may separate into different grain size fractions for the studied 2006 dust fall. The Sr and Nd isotope compositions further confirm that the 2006 dust fall and Pleistocene loess in Beijing have different sources. The loess deposits found in Beijing and those found on the Chinese Loess Plateau also derive from different sources. Variations between Sr and Nd isotopic compositions and Nd model ages with grain size need to be considered when directly comparing analyses of eolian dust of different grain size. (author)

Effect of temperature on the luminescence of Sm{sup 3+} ions in YAM crystals

Energy Technology Data Exchange (ETDEWEB)

Kaczkan, M. [Institute of Microelectronics and Optoelectronics PW, ul. Koszykowa 75, 00-662 Warsaw (Poland); Boruc, Z., E-mail: z.boruc@stud.elka.pw.edu.pl [Institute of Microelectronics and Optoelectronics PW, ul. Koszykowa 75, 00-662 Warsaw (Poland); Turczyński, S. [Institute of Electronic Materials Technology, ul. Wólczyńska 133, 01-919 Warsaw (Poland); Malinowski, M. [Institute of Microelectronics and Optoelectronics PW, ul. Koszykowa 75, 00-662 Warsaw (Poland)

2014-11-05

Highlights: • Different concentration Sm{sup 3+}-doped Y{sub 4}Al{sub 2}O{sub 9} crystals are fabricated by μ-pulling down method. • Thermally activated {sup 4}F{sub 3/2} → {sup 6}H{sub 5/2} emission of Sm{sup 3+} in YAM is studied. • Temperature dependent quenching mechanism of the {sup 4}G{sub 5/2} luminescence is proposed. - Abstract: The spectroscopic features of samarium Sm{sup 3+} activated Y{sub 4}Al{sub 2}O{sub 9} (YAM) crystals are presented and discussed. Temperature sensing properties of Sm{sup 3+}:YAM phosphor was demonstrated over the 300–1200 K range. Temperature dependent luminescence spectra and decay curves for the {sup 4}G{sub 5/2} level of Sm{sup 3+} in YAM were measured. Ratio of the fluorescence intensities arising from the two close lying {sup 4}F{sub 3/2} and {sup 4}G{sub 5/2} levels (with energy separation of ΔE ∼ 1000 cm{sup −1}) followed a straight line pattern, which confirms the Boltzmann distribution of the population, and can be used to measure temperature. The lifetime for the {sup 4}G{sub 5/2} level in 1% Sm doped sample decreases from 1.65 to 0.08 ms with heating from room temperature to 1200 K. This behavior of decays is discussed in terms of radiative and multiphonon decays as well as cross-relaxation dependence on temperature.

Preparation of 1 Ci of europium 155 without carrier; Une methode de production d'europium 155 sans entraineur au niveau du curie

Energy Technology Data Exchange (ETDEWEB)

Falconi, N; Radicella, R [Commissariat a l' Energie Atomique, Dir. des Materiaux et Combustibles Nucleaires, Saclay (France). Centre d' Etudes Nucleaires

1968-07-01

High activity 'point' sources of {sup 155}Eu are used for medical and industrial applications. For this purpose we have studied a method of obtaining I Ci of carrier free {sup 155}Eu, with a solid residue smaller than 5 mg per Ci. In order to separate the {sup 155}Eu from several grams of a {sup 154}Sm enriched target we propose a procedure which is based on the work of Bouissieres and David, Onstott, and Takekoshi et al. The separation is carried out by electrolysis on a mercury cathode followed by purification on ion exchange resin. The yields of the europium separation and target recovery are 80 per cent and 90 per cent respectively. The time required for the procedure is three days. (authors) [French] L'obtention de sources ponctuelles de haute activite d'europium-l55 est interessante tant pour des usages medicaux qu'industriels. Nous avons cherche le moyen de preparer en une seule fois, une solution d'un curie d'europium-155 sans entraineur presentant un extrait sec inferieur a 5 mg par curie. En se basant sur des travaux de Bouissieres et Davis, d'Onstott, et de Takekoshi et coll., nous avons mis au point une methode permettant de separer l'europium-155 de sa cible de samarium enrichi en {sup 154}Sm par une electrolyse sur cathode de mercure suivie d'une purification sur resine echangeuse d'ions. Les rendements chimiques de separation de l'europium et de recuperation de la cible de samarium enrichi sont respectivement de 80 pour cent et 90 pour cent. La duree de l'operation est de 3 jours. (auteurs)

Evaluation of genotoxic and cytotoxic effects of 153 Sm-EDTMP in peripheral blood lymphocytes of bone metastasis patients

International Nuclear Information System (INIS)

Suzuki, Miriam Fussae

2003-01-01

In this study the cellular damage in peripheral lymphocytes after exposure to 153 Sm-EDTMP (Samarium-153 ethylene-diamine-tetramietylene-phosphonate) was determined using the technique of micronuclei analysis and differential coloration. 153 Sm-EDTMP is a radiopharmaceutical used for pain relief in patients with bone metastases. The analysis of the frequency of micronuclei in patient blood samples obtained one hour after endovenous administration of radiopharmaceutical (41 MBq/kg) showed no statistical difference in relation to basal values in binucleated cells. However the analysis of damage distribution in mononucleated cells, showed that the patients without previous radiotherapy treatment presented a significant increase in the frequency of cells with one micronucleus and in those who had taken previous radiotherapy treatment, in cells with two or more micronuclei. The in vitro experiments conducted with the exposition of total blood to three radiation concentrations of 153 Sm-EDTMP (0.370, 0.555 and 1.110 MBq/mL) during one hour showed an increase in the frequency of micronuclei and necrotic and apoptotic cells with increasing radiation dose. Dose-response curves for healthy donors and patients with bone metastasis without previous radiotherapy treatment were constructed. The comparison of the curves showed that patients presented higher radiosensitivity, either micronuclei or dead cell (necrotic or apoptotic) percentages, than healthy donors. (author)

Systemic Radiopharmaceutical Agents (Sm-153) may be Dangerous in Hepatacellular Carcinoma

Science.gov (United States)

Keskin, Onur; Soydal, Cigdem; Deda, Xheni; Manti, Bengu; Tuzun, Ali

2015-01-01

Palliation of bone metastases in hepatocellular carcinoma (HCC) is sometimes difficult. Systemic pharmaceuticals have been successfully used for the palliation of bone metastasis for many years. Safety of these agents in HCC is not known completely. We presented a male patient with decompensated liver cirrhosis with HCC. Multifocal bone metastases developed in this patient and he had refractory bone pain. We treated this patient with Sm-153 (samarium) after obtaining patient's consent. Two days after treatment, he experienced dyspnea and we detected a massive hemorrhagic pericardial effusion. He died due to this unexpected bleeding. We should use this radiopharmaceutical treatment cautiously in these cytopenic cirrhotic patients. PMID:25709546

Development of atomic spectroscopy technology -Development of ultrasensitive spectroscopic analysis technology

Energy Technology Data Exchange (ETDEWEB)

Cha, Hyung Kee; Suk, Song Kyoo; Kim, Duk Hyun; Hong, Suk Kyung; Lee, Yong Joo; Lee, Jong Hoon; Yang, Kee Hoh [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

For the resonance ionization spectroscopy experiment, erbium and samarium were chosen as test elements and their optimum photoionization schemes for trace analysis have been investigated by using multiphoton spectroscopic techniques. With the optimum scheme, the detection limit of various atoms were measured. For the test of laser induced fluorescence system, calibration curves obtained from lead and cadmium standard solutions were made and Pb concentrations of various unknown solutions were determined. By using the developed differential absorption lidar system, backscattering signals from aerosol and ozone have been measured. Error source, error calibration and data interpretation techniques have been also studied. 60 figs, 8 pix, 28 tabs, 30 refs. (Author).

The usage of Sm/Nd isotopic signature of granites as a tool for defining sub-domains in the southern tectonic domain, Borborema province, NE, Brazil

International Nuclear Information System (INIS)

Silva Filho, A.F. da; Guimaraes, I.P.; Luna, E.B.A.; Van Schmus, W.R.

1997-01-01

The geologic and geotectonic status of the PE-AL Massif (PAM), northeastern region of Brazil, has been debated over the past three decades by various authors and the complexity of the area could have been one among some reasons for such long debate, beside the lack of detailed geologic data. The work presents the characteristics of the various batholiths named as the Toritama -Arcoverde, Jaboatao-Garanhuns, Ipojuca-Atalaia, Maribondo-Correntes, Buique-Paulo Afonso, and Aguas Belas-Caninde batholiths. Finally, it shows the results of a Samarium/Neodymium (Sm/Nd) analysis of 55 samples that suggested the existence of two domains in the eastern PAM

Performance of the Brookhaven photocathode rf gun

International Nuclear Information System (INIS)

Batchelor, K.; Ben-Zvi, I.; Fernow, R.C.; Fischer, J.; Fisher, A.S.; Gallardo, J.; Ingold, G.; Kirk, H.G.; Leung, K.P.; Malone, R.; Pogorelsky, I.; Srinivasan-Rao, T.; Rogers, J.; Tsang, T.; Sheehan, J.; Ulc, S.; Woodle, M.; Xie, J.; Zhang, R.S.; Lin, L.Y.; McDonald, K.T.; Russell, D.P.; Hung, C.M.; Wang, X.J.

1991-01-01

The Brookhaven Accelerator Test Facility (ATF) uses a photocathode rf gun to provide a high-brightness electron beam intended for FEL and laser-acceleration experiments. The rf gun consists of 1 1/2 cells driven at 2856 MHz in π-mode with a maximum cathode field of 100 MV/m. To achieve long lifetimes, the photocathode development concentrates on robust metals such as copper, yttrium and samarium. We illuminate these cathodes with a 10-ps, frequency-quadrupled Nd:YAG laser. We describe the initial operation of the gun, including measurements of transverse and longitudinal emittance, quantum efficiencies, and peak current. The results are compared to models

Raw materials for advanced ceramics: rare earths separation processes

International Nuclear Information System (INIS)

Ricci, D.R.; Nobre, J.S.M.; Paschoal, J.O.A.

1990-01-01

The importance of obtaining purified rare earths oxidesis related, mainly to the increasing use of these compounds as raw materials for advanced ceramics. Processes of rare earths separation and purification are almost always based on the solvent extraction, fractional precipitation and ion exchange chromatography techniques, whose association depends on the initial concentrate and on the desired purity. This paper describes some steps of fractionation of didymium carbonate by using the solvent extraction and fractional precipitation techniques. The experimental conditions presented here have enable the production of lantanium, neodimium - praseodimium, samarium - gadolinium and ytrium concentrates, which constitute the intermediate fractions of the overall process to obtain high purity rare earths. (author) [pt

Green inhibitors. Rare Earth based systems

International Nuclear Information System (INIS)

Aballe, A.; Bethencourt, M.; Botana, F.J.; Perez, J.; Rodriguez, M.A.; Marcos, M.

1997-01-01

Lanthanum, Cerium and Samarium chlorides have been investigated as uniform and pitting corrosion inhibitors of AISI 434 and AISI 304 stainless steels and AA 5083 Al-Mg alloy in 3.5% Na Cl aerated aqueous solutions. Their inhibitor power was evaluated by using electrochemical techniques such as Linear and Cyclic Polarisation. In each case, the highest protection degree was found in the solution dropped with 500 ppm of CeCl 3 . Similar results were obtained for additions of 500 ppm of LaCl 3 . Scanning Electron Microscopy and Energy Dispersive Spectroscopy allowed us to confirm the cathodic nature of the inhibition process. (Author) 27 refs

Determination of micro amounts of praseodymium by analogue derivative spectrophotometry

International Nuclear Information System (INIS)

Ishii, Hajime; Satoh, Katsuhiko.

1986-01-01

Derivative spectrophotometry using the analogue differentiation circuit was applied to the determination of praseodymium at the ppm level. By the proposed method, in which the second or fourth derivative spectrum of the characteristic absorption band of praseodymium(III) at 444 nm is measured, as little as 3 ppm of praseodymium can be determined directly and easily even in the presence of large amounts of other rare earths without any prior separation. Interferences from neodymium, samarium, dysprosium, holmium and erbium ions which have characteristic absorption bands around 444 nm can easily be removed by utilizing the isosbestic point in the derivative spectra of praseodymium(III) and the interfering rare earth(III). (author)

Analytical determination of traced elements in concrete samples used in nuclear reactors of the European Community

International Nuclear Information System (INIS)

May, S.; Piccot, D.

1984-01-01

In reactor dismantling residual radioacting of concrete used, especially in biological shield can brought problems for treatment and disposal. Radioactivity of concrete from reactors can be forecasted if element content is known. Elements producing long life radionuclides are: chlorine, calcium nickel, cobalt, niobium, europium and samarium. Neutron activation analysis is used for determination of these elements whithout chemical separation for Ca, Co, Eu and Sm and with radiochemical separation for Cl, Ni and Nb. A lot of elements, less interesting are also determined by gamma spectrometry after irradiation. It was possible to determine 29 elements in 21 concrete samples from different European Community reactors

Development of atomic spectroscopy technology -Development of ultrasensitive spectroscopic analysis technology

International Nuclear Information System (INIS)

Cha, Hyung Kee; Song Kyoo Suk; Kim, Duk Hyun; Hong, Suk Kyung; Lee, Yong Joo; Lee, Jong Hoon; Yang, Kee Hoh

1995-07-01

For the resonance ionization spectroscopy experiment, erbium and samarium were chosen as test elements and their optimum photoionization schemes for trace analysis have been investigated by using multiphoton spectroscopic techniques. With the optimum scheme, the detection limit of various atoms were measured. For the test of laser induced fluorescence system, calibration curves obtained from lead and cadmium standard solutions were made and Pb concentrations of various unknown solutions were determined. By using the developed differential absorption lidar system, backscattering signals from aerosol and ozone have been measured. Error source, error calibration and data interpretation techniques have been also studied. 60 figs, 8 pix, 28 tabs, 30 refs. (Author)

Some radiation protection problems connected with the use of 186Re-HEDP and 153Sm-EDTMP for palliative therapy of of bone metastases

International Nuclear Information System (INIS)

Husak, V.; Myslivecek, M.

1995-01-01

The aim of this paper was to assess whether the ambulatory (outpatient) therapy with 186 Re-HEDP and 153 Sm-EDTMP is possible in the Czech Republic. Physical characteristics, administered activity, biokinetics of radiopharmaceuticals, radiation protection characteristics, irradiation of patients relatives as well as comparison with limits for rhenium-186 and samarium-153 radiopharmaceuticals are given. The outpatient administration of 186 Re-HEDP and 153 Sm-EDTMP with the subsequent keeping the patient for 6 hours in a department of nuclear medicine appears to be in compliance with regulations proposed in the Czech Republic as well as ICRP Recommendations. (J.K.) 1 tab., 12 refs

Dynamic modeling of brushless dc motor-power conditioner unit for electromechanical actuator application

Science.gov (United States)

Demerdash, N. A.; Nehl, T. W.

1979-01-01

A comprehensive digital model for the analysis of the dynamic-instantaneous performance of a power conditioner fed samarium-cobalt permanent magnet brushless DC motor is presented. The particular power conditioner-machine system at hand, for which this model was developed, is a component of an actual prototype electromechanical actuator built for NASA-JSC as a possible alternative to hydraulic actuators as part of feasibility studies for the shuttle orbiter applications. Excellent correlation between digital simulated and experimentally obtained performance data was achieved for this specific prototype. This is reported on in this paper. Details of one component of the model, its applications and the corresponding results are given in this paper.

The usage of Sm/Nd isotopic signature of granites as a tool for defining sub-domains in the southern tectonic domain, Borborema province, NE, Brazil

Energy Technology Data Exchange (ETDEWEB)

Silva Filho, A.F. da; Guimaraes, I.P.; Luna, E.B.A. [Pernambuco Univ., Recife, PE (Brazil). Dept. de Geologia; Van Schmus, W.R. [Kansas Univ., Lawrence, KS (United States). Dept. of Geology

1997-12-31

The geologic and geotectonic status of the PE-AL Massif (PAM), northeastern region of Brazil, has been debated over the past three decades by various authors and the complexity of the area could have been one among some reasons for such long debate, beside the lack of detailed geologic data. The work presents the characteristics of the various batholiths named as the Toritama -Arcoverde, Jaboatao-Garanhuns, Ipojuca-Atalaia, Maribondo-Correntes, Buique-Paulo Afonso, and Aguas Belas-Caninde batholiths. Finally, it shows the results of a Samarium/Neodymium (Sm/Nd) analysis of 55 samples that suggested the existence of two domains in the eastern PAM

Some radiation protection problems connected with the use of 186Re-HEDP and 153Sm-EDTMP for palliative therapy of of bone metastases

Energy Technology Data Exchange (ETDEWEB)

Husak, V; Myslivecek, M [Univ. Hospital, Olomouc (Czech Republic). Department of Nuclear Medicine

1996-12-31

The aim of this paper was to assess whether the ambulatory (outpatient) therapy with {sup 186}Re-HEDP and {sup 153}Sm-EDTMP is possible in the Czech Republic. Physical characteristics, administered activity, biokinetics of radiopharmaceuticals, radiation protection characteristics, irradiation of patients relatives as well as comparison with limits for rhenium-186 and samarium-153 radiopharmaceuticals are given. The outpatient administration of {sup 186}Re-HEDP and {sup 153}Sm-EDTMP with the subsequent keeping the patient for 6 hours in a department of nuclear medicine appears to be in compliance with regulations proposed in the Czech Republic as well as ICRP Recommendations. (J.K.) 1 tab., 12 refs.

Die selfverstaan van die Samaritane soos dit uit- drukking vind in die feesliturgie צלות מוצד השמיני

Directory of Open Access Journals (Sweden)

J. Beyers

1999-12-01

Full Text Available The self-understanding of the Samaritans, as expressed in the liturgy of the צלות מוצד השמיני festival This study is concerned with the identity and religion of the Samaritans. The way in which the Samaritans understood their identity is highlighted by their perception of God, by the traditions they adhered to and by the selection of texts from the Pentateuch they used in their liturgy. The beliefs and rituals of the Samarium faith found their way into the Samaritan Liturgy. The study of a part of the Samaritan Liturgy shows that the Samaritans are heirs to the religion of the northern tibes of Israel.

X-ray fluorescence analysis of praseodymium oxide/oxalate for rare earth impurities

International Nuclear Information System (INIS)

Chandola, L.C.; Mohile, A.N.

1976-01-01

A method for the determination of lanthanum, cerium, neodymium and samarium oxides in praseodymium oxide is described. The sample in the oxalate form is mixed with boric acid binder in the weight ratio of 1:1 and pressed into a pellet. The pellet is irradiated by X-rays from a tungsten tube and fluorescent X-rays are dispersed by a LiF (200) crystal in a Philips semiautomatic X-ray fluorescence spectrometer. The intensity of the characteristic X-rays of the impurity elements is measured by a flow proportional counter at selected 20 angles. The minium determination limit is 0.01% for all impurities. (author)

A superconducting linear motor drive for a positive displacement bellows pump for use in the g-2 cryogenics system

International Nuclear Information System (INIS)

Green, M.A.

1994-10-01

Forced two-phase cooling of indirectly cooled magnets requires circulation of liquid helium through the magnet cooling channel. A bellows helium pump is one possible way of providing helium flow to a magnet cooling system. Since the bellows type of helium pump is immersed in liquid helium, a superconducting linear motor drive appears to be an attractive option. This report describes a linear motor drive that employs oriented permanent magnet materials such as samarium-cobalt as the stator magnet system and a superconducting loud speaker voice coil type of drive as the armature of the linear motor. This report examines drive motor requirements for a helium pump

Determination of rare earth impurities in thorium by spectrographic methods

Energy Technology Data Exchange (ETDEWEB)

Wray, L W

1957-08-15

A method for determining rare earth impurities in thorium in the fractional ppm range is described. Before spectrographic examination is possible, the impurities must be freed from the thorium matrix. This is accomplished by removing the bulk of the thorium by extraction with TBP-CCl{sub 4} and the remainder by extraction with TTA-C{sub 6}H{sub 6}. This results in a consistent recovery of rare earths of about 85% with an average sensitivity of 0.2 ppm. The experimental error is within 10%. Details of the procedure are given together with working curves for the major neutron absorbing rare earths; i.e. dysprosium, europium, gadolinium and samarium. (author)

Direct two-photon excitation of Sm3+, Eu3+, Tb3+, Tb.DOTA-, and Tb.propargylDO3A in solution

Science.gov (United States)

Sørensen, Thomas Just; Blackburn, Octavia A.; Tropiano, Manuel; Faulkner, Stephen

2012-07-01

We have observed direct two-photon excitation of samarium, europium and terbium ions in solution upon near IR excitation using a tuneable pulsed light source, and have also studied two-photon processes in a pair of related terbium complexes, namely [Tb.DOTA]- and Tb.propargylDO3A. Direct two-photon excitation of lanthanides is observed in simple systems in the absence of sensitizing chromophores. Where even simple chromophores such as a triple bond are present in the complex, then single and two-photon excitation of chromophore excited states competes with direct two-photon excitation of the ions and is the dominant pathway for sensitizing formation of the lanthanide excited state.

Effect of absorption discontinuity on neutron spectra of water assemblies poisoned with non-1/V absorbers

International Nuclear Information System (INIS)

Gupta, I.J.; Trikha, S.K.

1977-01-01

Calculations are presented of the diffusion of thermal neutrons (2.5 x 10 -4 to 7 x 10 -1 eV) across an absorption discontinuity in a water assembly, consisting of pure water on one side and aqueous solutions of three different non-1/V absorbers on the other, which were obtained by solving the Boltzmann transport equation in the diffusion approximation using the multigroup formalism. The gradual appearance and disappearance of the depletion region in the neutron spectra (caused by the resonance absorption peaks at energies 0.096 and 0.179 eV for samarium and cadmium respectively), as one moves from the pure water assembly to the poisoned water assembly and vice versa, have also been studied. The minimum concentrations of Sm and Cd atoms in water for which the depletion region in the spectra just starts building up are found to be 60 x 10 18 Sm atom cm -3 and 125 x 10 18 Cd atom cm -3 respectively. However no such depletion region is observed in gadolinium-poisoned water assembly. At the boundary, the equilibrium neutron distribution gets disturbed and is re-established to the equilibrium distribution of the second medium at some distance from the interface. The diffusion lengths so calculated from the total neutron density curves are in good agreement with the experimental results of Goddard and Johnson (Nucl. Sci. Eng.; 37:127 (1969)) at various concentrations of Gd and Cd atoms in water. (author)

Adjustable Permanent Quadrupoles Using Rotating Magnet Material Rods for the Next Linear Collider

International Nuclear Information System (INIS)

Spencer, Cherrill M

2002-01-01

The proposed Next Linear Collider (NLC) will require over 1400 adjustable quadrupoles between the main linacs' accelerator structures. These 12.7 mm bore quadrupoles will have a range of integrated strength from 0.6 to 132 Tesla, with a maximum gradient of 135 Tesla per meter, an adjustment range of +0 -20% and effective lengths from 324 mm to 972 mm. The magnetic center must remain stable to within 1 micrometer during the 20% adjustment. In an effort to reduce estimated costs and increase reliability, several designs using hybrid permanent magnets have been developed. All magnets have iron poles and use either Samarium Cobalt or Neodymium Iron to provide the magnetic fields. Two prototypes use rotating rods containing permanent magnetic material to vary the gradient. Gradient changes of 20% and center shifts of less than 20 microns have been measured. These data are compared to an equivalent electromagnet prototype. See High Reliability Prototype Quadrupole for the Next Linear Collider by C.E Rago, C.M SPENCER, Z. Wolf submitted to this conference

Energy transfer mechanism from Gd3+ to Sm3+ in K3Gd(PO4)2:Sm3+ phosphor

International Nuclear Information System (INIS)

Gupta, Palvi; Bedyal, A K; Kumar, Vinay; Khajuria, Y; Sharma, Vishal; Ntwaeaborwa, O M; Swart, H C

2015-01-01

Undoped K 3 Gd(PO 4 ) 2 and trivalent samarium (0.5–2.5 mol%) doped K 3 Gd(PO 4 ) 2 phosphors were synthesized by the solid-state method. The phase formation, optical and luminescence properties were investigated by x-ray diffraction (XRD), diffuse reflectance (DR) spectroscopy, and photoluminescence (PL) spectroscopy. The fluorescence decay spectra of the obtained phosphors were also recorded to study the energy transfer from sensitizer (Gd 3+ ) to activator (Sm 3+ ). Energy transfer effects from sensitizer to activator caused by rare-earth ions were mainly observed in the obtained PL and lifetime spectra. The decay curves of K 3 Gd(PO 4 ) 2 phosphor with different Sm 3+ ions concentrations were found to be non-exponential and the data is well fitted with the Inokuti–Hirayama (I–H) model. The energy transfer parameters such as critical distance for the transfer processes were determined. The Commission Internationale de l’Eclairage (CIE) chromatic coordinates and color-correlated temperature were also determined for the prepared phosphor. (paper)

Genetic algorithm based approach to investigate doped metal oxide materials: Application to lanthanide-doped ceria

Science.gov (United States)

Hooper, James; Ismail, Arif; Giorgi, Javier B.; Woo, Tom K.

2010-06-01

A genetic algorithm (GA)-inspired method to effectively map out low-energy configurations of doped metal oxide materials is presented. Specialized mating and mutation operations that do not alter the identity of the parent metal oxide have been incorporated to efficiently sample the metal dopant and oxygen vacancy sites. The search algorithms have been tested on lanthanide-doped ceria (L=Sm,Gd,Lu) with various dopant concentrations. Using both classical and first-principles density-functional-theory (DFT) potentials, we have shown the methodology reproduces the results of recent systematic searches of doped ceria at low concentrations (3.2% L2O3 ) and identifies low-energy structures of concentrated samarium-doped ceria (3.8% and 6.6% L2O3 ) which relate to the experimental and theoretical findings published thus far. We introduce a tandem classical/DFT GA algorithm in which an inexpensive classical potential is first used to generate a fit gene pool of structures to enhance the overall efficiency of the computationally demanding DFT-based GA search.

Feasibility Study of Coupling the CASMO-4/TABLES-3/SIMULATE-3 Code System to TRACE/PARCS

International Nuclear Information System (INIS)

Demaziere, Christophe; Staalek, Mathias

2004-12-01

This report investigates the feasibility of coupling the Studsvik Scandpower CASMO-4/TABLES-3/SIMULATE-3 codes to the US NRC TRACE/PARCS codes. The data required by TRACE/PARCS are actually the ones necessary to run its neutronic module PARCS. Such data are the macroscopic nuclear cross-sections, some microscopic nuclear cross-sections important for the Xenon and Samarium poisoning effects, the Assembly Discontinuity Factors, and the kinetic parameters. All these data can be retrieved from the Studsvik Scandpower codes. The data functionalization is explained in detail for both systems of codes and the possibility of coupling each of these codes to TRACE/PARCS is discussed. Due to confidentiality restrictions in the use of the CASMO-4 files and to an improper format of the TABLES-3 output files, it is demonstrated that TRACE/PARCS can only be coupled to SIMULATE-3. Specifically-dedicated SIMULATE-3 input decks allow easily editing the neutronic data at specific operating statepoints. Although the data functionalization is different between both systems of codes, such a procedure permits reconstructing a set of data directly compatible with PARCS

New burnup calculation of TRIGA IPR-R1 reactor

International Nuclear Information System (INIS)

Meireles, Sincler P. de; Campolina, Daniel de A.M.; Santos, Andre A. Campagnole dos; Menezes, Maria A.B.C.; Mesquita, Amir Z.

2015-01-01

The IPR-R1 TRIGA Mark I research reactor, located at the Nuclear Technology Development Center - CDTN, Belo Horizonte, Brazil, operates since 1960.The reactor is operating for more than fifty years and has a long history of operation. Determining the current composition of the fuel is very important to calculate various parameters. The reactor burnup calculation has been performed before, however, new techniques, methods, software and increase of the processing capacity of the new computers motivates new investigations to be performed. This work presents the evolution of effective multiplication constant and the results of burnup. This new model has a more detailed geometry with the introduction of the new devices, like the control rods and the samarium discs. This increase of materials in the simulation in burnup calculation was very important for results. For these series of simulations a more recently cross section library, ENDF/B-VII, was used. To perform the calculations two Monte Carlo particle transport code were used: Serpent and MCNPX. The results obtained from two codes are presented and compared with previous studies in the literature. (author)

Research on optical applications in nuclear industry

International Nuclear Information System (INIS)

Kim, Cheol Jung; Shin, Jang Soo; Lee, Sang Mock; Baik, Sung Hoon; Kwon, Seong Ouk; Hong, Suc Kyoung; Kim, Duk Hyeon

1988-12-01

The laser fluorometer developed in 1987 has been modified to compensate the inner filter and quenching effects. The signal processing electronic circuit was redesigned and a computer interface was introduced for data processing. It has been already used in routine chemical analysis in the chemical analysis division. Its application to uranium monitoring in conversion plant is being investigated. Also, we found that it can be used in trace analysis of samarium and europium with detection limit of 1 ppb and 0.1 ppb, respectively. The IRMPA/D process of CDF 3 and CHF 3 have been studied. The pressure effects of CDF 3 ,CHF 3 and added buffer gas were investigated. Mainly, the change in reaction rate was examined while varying the pressure of CDF 3 , CHF 3 and buffer gas. The IRMPD reaction ratio of CDF 3 and CHF 3 from below 0.1 torr up to a few torr was studied and the buffer gas pressure effect was investigated at constant pressure of CDF 3 or CHF 3 of 1 torr. Several kinds of buffer gas, Ar, N 2 , and SF 6 , were used to investigate the buffer gas pressure effect. We applied double exposure holographic interferometry, and analyzed qualitatively the distortion due to thermal heat and vibration. The research on holographic remote inspection will be achieved to apply this technique to the nuclear fuel cycle facilities. (Author)

Determination of first ionization potential of samarium atom using Rydberg series convergence

International Nuclear Information System (INIS)

Jayasekharan, T.; Razvi, M.A.N.; Bhale, G.L.

1999-01-01

The study of Rydberg states has recently received more attention partially because an efficient isotope selective ionization is possible via these states. In addition, their investigation provides useful information on the atomic structure. An electron in a shell with a high principal quantum number is a sensitive probe for the interaction with the ionic core of the atom. Measurements of these Rydberg levels give valuable data on quantum defects, anomalies in fine structure splitting, polarizabilities, configuration interactions, ionization potentials etc

Structural and impedance spectroscopic studies of samarium modified lead zirconate titanate ceramics

Energy Technology Data Exchange (ETDEWEB)

Ranjan, Rajiv [Department of Physics, Jamshedpur Co-operative College, Jamshedpur 831036 (India); Kumar, Rajiv [Department of Physics, Jamshedpur Worker' s College, Jamshedpur 831012 (India); Behera, Banarji [Department of Physics and Meteorology, I.I.T. Kharagpur 721302 (India); Choudhary, R.N.P., E-mail: crnpfl@phy.iitkgp.ernet.i [Department of Physics and Meteorology, I.I.T. Kharagpur 721302 (India)

2009-11-01

The polycrystalline samples of Pb{sub 1-x}Sm{sub x}(Zr{sub 0.60}Ti{sub 0.40}){sub 1-x/4}O{sub 3} (PSZT) where x=0.00, 0.03, 0.06 and 0.09 were prepared by a high-temperature solid-state reaction technique. The preliminary structural analysis using X-ray diffraction (XRD) data collected at room temperature has confirmed the formation of single-phase compounds in tetragonal crystal system. The morphological study of each sample using scanning electron microscope (SEM) has revealed that the grains are uniformly distributed through out the surfaces of the samples. Using complex impedance spectroscopy (CIS) technique, the electrical impedance and modulus properties of the materials were studied in a wide range of temperatures at different frequencies. The impedance analysis indicates the presence of bulk resistive contributions in the materials which is found to decrease on increasing temperature. The nature of variation of resistances with temperature suggests a typical negative temperature coefficient of resistance (NTCR) type behavior of the materials. The complex modulus plots clearly exhibits the presence of grain boundaries along with the bulk contributions in the PSZT materials. The presence of non-Debye type of relaxation has been confirmed by the complex impedance analysis. The variation of dc conductivity (bulk) with temperature demonstrates that the compounds exhibit Arrhenius type of electrical conductivity.

Comment on ''Spectroscopy of samarium isotopes in the sdg interacting boson model''

International Nuclear Information System (INIS)

Kuyucak, S.; Lac, V.

1993-01-01

We point out that the data used in the sdg boson model calculations by Devi and Kota [Phys. Rev. C 45, 2238 (1992)] can be equally well described by the much simpler sd boson model. We present additional data for the Sm isotopes which cannot be explained in the sd model and hence may justify such an extension to the sdg bosons. We also comment on the form of the Hamiltonian and the transition operators used in this paper

Post-assembly magnetization of a 100 kW high speed permanent magnet rotor.

Science.gov (United States)

Lv, Yiliang; Wang, Guobin; Li, Liang

2015-03-01

A post-assembly magnetizing fixture has been designed and successfully used to magnetize the rotor of a 100 kW high speed permanent magnet synchronous motor. The rotor is a solid cylinder with outer diameter of 80 mm and total length of 515 mm. The permanent magnet material is samarium-cobalt (Sm2Co17) with saturation magnetizing field of 6 T. The mechanical stability of the magnetizing fixture has been studied as well as the general design methodology. The magnetizing coil is subdivided in order to reduce the electromagnetic force, and the coils are separately reinforced in different ways. The electromagnetic and structural optimization is performed by finite element analysis and verified by experiments.

Post-assembly magnetization of a 100 kW high speed permanent magnet rotor

International Nuclear Information System (INIS)

Lv, Yiliang; Wang, Guobin; Li, Liang

2015-01-01

A post-assembly magnetizing fixture has been designed and successfully used to magnetize the rotor of a 100 kW high speed permanent magnet synchronous motor. The rotor is a solid cylinder with outer diameter of 80 mm and total length of 515 mm. The permanent magnet material is samarium-cobalt (Sm 2 Co 17 ) with saturation magnetizing field of 6 T. The mechanical stability of the magnetizing fixture has been studied as well as the general design methodology. The magnetizing coil is subdivided in order to reduce the electromagnetic force, and the coils are separately reinforced in different ways. The electromagnetic and structural optimization is performed by finite element analysis and verified by experiments

Post-assembly magnetization of a 100 kW high speed permanent magnet rotor

Energy Technology Data Exchange (ETDEWEB)

Lv, Yiliang; Wang, Guobin [Wuhan National High Magnetic Field Center, Huazhong University of Science and Technology, Wuhan (China); Li, Liang [Wuhan National High Magnetic Field Center, Huazhong University of Science and Technology, Wuhan (China); State Key Laboratory of Advanced Electromagnetic Engineering and Technology, Huazhong University of Science and Technology, Wuhan (China)

2015-03-15

A post-assembly magnetizing fixture has been designed and successfully used to magnetize the rotor of a 100 kW high speed permanent magnet synchronous motor. The rotor is a solid cylinder with outer diameter of 80 mm and total length of 515 mm. The permanent magnet material is samarium-cobalt (Sm{sub 2}Co{sub 17}) with saturation magnetizing field of 6 T. The mechanical stability of the magnetizing fixture has been studied as well as the general design methodology. The magnetizing coil is subdivided in order to reduce the electromagnetic force, and the coils are separately reinforced in different ways. The electromagnetic and structural optimization is performed by finite element analysis and verified by experiments.

Synthesis and characterization of rare-earth-doped calcium tungstate nanocrystals

Science.gov (United States)

Suneeta, P.; Rajesh, Ch.; Ramana, M. V.

2018-02-01

In this paper, we report synthesis and characterization of rare-earth-ion-doped calcium tungstate (CaWO4) nanocrystals (NCs). Rare-earth ions, such as gadolinium (Gd), neodymium (Nd), praseodymium (Pr), samarium (Sm) and holmium (Ho), were successfully doped in the CaWO4 NCs by changing the synthesis conditions. The adopted synthesis route was found to be fast and eco-friendly. Structural characterizations, such as X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and compositional analysis, were performed using energy dispersive analysis of X-rays (EDAX) on as-synthesized NCs. The results indicate the size of the NCs ranging between 47 to 68nm and incorporation of rare-earth ions in CaWO4 NCs.

Raman spectroscopic studies of Nd{sub 0.75}Sm{sub 0.25}GaO{sub 3} single crystals

Energy Technology Data Exchange (ETDEWEB)

Nithya, R., E-mail: nithya@igcar.gov.in; Ravindran, T. R. [Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam-603102, TN (India); Daniel, D. J. [Centre for Crystal Growth, SSN College of Engineering, Kalavakkam-603110, TN (India)

2015-06-24

Single crystals of Nd{sub 1-x}Sm{sub x}GaO{sub 3} (x= 0 and 0.25) were grown by a four mirror IR image furnace using floating zone technique. The crystals are characterized by X-ray diffraction and Raman spectroscopic measurements. NGO adopts orthorhombic structure with Pbnm symmetry and samarium substituted compound also exhibited the same structure as that of the pristine compound without secondary phases. Polarized Raman spectra are measured at ambient temperature in a back scattering geometry. Spectra exhibit low intensity first-order Raman bands. In addition, several high intensity second-order Raman bands have been observed in the frequency range 2000 to 4000 cm{sup −1}.

Electronically commutated dc motors for electric vehicles

Science.gov (United States)

Maslowski, E. A.

1981-01-01

A motor development program to explore the feasibility of electronically commutated dc motors (also known as brushless) for electric cars is described. Two different design concepts and a number of design variations based on these concepts are discussed. One design concept is based on a permanent magnet, medium speed, machine rated at 7000 to 9000 rpm, and powered via a transistor inverter power conditioner. The other concept is based on a permanent magnet, high speed, machine rated at 22,000 to 26,000 rpm, and powered via a thyristor inverter power conditioner. Test results are presented for a medium speed motor and a high speed motor each of which have been fabricated using samarium cobalt permanent magnet material.

Studies of Some Lanthanide(III Nitrate Complexes of Schiff Base Ligands

Directory of Open Access Journals (Sweden)

Kishor Arora Mukesh Sharma

2009-01-01

Full Text Available The studies of 16 new lanthanide(III nitrate complexes of Schiff base ligands are discussed. Schiff bases were obtained by the condensation of 2–methyl–4–N,N–bis–2' –cyanoethyl aminobenzaldehyde with aniline and 3 different substituted anilines. Lanthanide(III nitrates, viz. gadolinium(III nitrate, lanthanum(III nitrate, samarium(III nitrate and cerium(III nitrate were chosen to synthesize new complexes. The complexes were characterized on the basis of physicochemical studies viz. elemental analysis, spectral, viz. IR and electronic spectral and magnetic studies. TGA studies of some of the representative complexes were also done. Some of the representative complexes were also screened for the anti microbial studies.

Dilatometric and dielectric behaviour of Sm modified PCT ceramics

International Nuclear Information System (INIS)

Singh, Sarabjit; Thakur, O.P.; Prakash, Chandra; Raina, K.K.

2005-01-01

Samarium modified PCT ceramics with composition (Pb 0.76-x Sm x Ca 0.24 )(Ti 0.98 Mn 0.02 )O 3 ; x=0-0.08 in steps of 0.02 were prepared by conventional mixed-oxide method. Detailed dilatometric studies were carried out for green specimens in order to study sintering behaviour. Change in the dilatometric behaviour is correlated with the XRD results of powders calcined at different temperatures. Dielectric constant was observed to increase with increasing Sm concentration, which has been attributed to reduced tetragonality and better densification on Sm substitution. SEM micrographs have revealed the grain size of the samples. Ferroelectric hysteresis behaviour was studied for all the compositions

On fluorozirconates and fluorohafnates of rare earths

International Nuclear Information System (INIS)

Korenev, Yu.M.; Antipov, P.I.; Novoselova, A.V.

1980-01-01

It has been shown by the method of X-ray phase analysis that on interaction between rare-earth fluorides and zirconium and hafnium tetrafluorides, compounds with 1:1, 1:2, 1:3 molar ratios of components are formed. Compounds of the LnHfF 4 type are prepared for all rare-earths. Fluoro-metals of the LnHf 2 F 11 composition are typical only of light lanthanides from lanthanum to neodymium, while pentafluorated salts Ln(EF 5 ) 3 are formed in the reaction between EF 4 with fluorides of heavy rare-earth elements from samarium to lutecium, as well as with yttrium trifluoride. Parameters of unit cells of heptafluohafnates and pentafluometallates are determined

UV photoemission studies of metal photocathodes for particle accelerators

International Nuclear Information System (INIS)

Fischer, J.; Srinivasan-Rao, T.

1988-01-01

Photoemission from several metals was studied with 10 ps laser pulses at 266 nm. The yield was linear with energy and with area. Quantum efficiencies (/eta/) were determined (up to 10/sup /minus/3/ e/photons for samarium), and found to vary as (hν-/phi/) 2 . /eta/ also increased with the field. The field assisted efficiencies were calculated for some metals and confirmed by experiment for gold, up to surface fields of /approximately/3/times/10 8 V/m. High charge and current densities, close to 10 5 A/cm 2 from macroscopic areas, were measured or indicated. Results are then related to applications in accelerators. 18 refs., 15 figs., 4 tabs

An electrochemical approach for removal of radionuclidic contaminants of Eu from 153Sm for effective use in metastatic bone pain palliation.

Science.gov (United States)

Chakravarty, Rubel; Chakraborty, Sudipta; Khan, Mohammed Sahiralam; Ram, Ramu; Sarma, Haladhar Dev; Dash, Ashutosh

2018-03-01

Thermal neutron activation of 152 Sm [ 152 Sm(n,γ) 153 Sm] using natural or isotopically enriched (by 152 Sm) samarium target is the established route for production of 153 Sm used for preparation of 153 Sm-EDTMP for pain palliation in cancer patients with disseminated bone metastases. However, some long-lived radionuclidic contaminants of Eu, such as, 154 Eu (t ½ =8.6y) are also produced during the target activation process. This leads to detectable amount of Eu radionuclidic contaminants in patients' skeleton even years after administration with therapeutic doses of 153 Sm-EDTMP. Further, the presence of such contaminants in 153 Sm raises concerns related to radioactive waste management. The aim of the present study was to develop and demonstrate a viable method for large-scale purification of 153 Sm from radionuclidic contaminants of Eu. A radiochemical separation procedure adopting electroamalgamation approach has been critically evaluated. The influence of different experimental parameters for the quantitative removal radionuclidic contaminants of Eu from 153 Sm was investigated and optimized. The effectiveness of the method was demonstrated by purification of ~37 GBq of 153 Sm in several batches. As a proof of concept, 153 Sm-EDTMP was administered in normal Wistar rats and ex vivo γ-spectrometry of bone samples were carried out. After carrying out the electrolysis under the optimized conditions, the radionuclidic contaminants of Eu could not be detected in purified 153 Sm solution by γ-spectrometry. The overall yield of 153 Sm obtained after the purification process was >85%. The reliability of this approach was amply demonstrated in several batches, wherein the performance remained consistent. Ex vivo γ-spectrometry of bone samples of Wistar rats administered with 153 Sm-EDTMP (prepared using electrochemically purified 153 Sm) did not show photo peaks corresponding to radionuclidic contaminants of Eu. A viable electrochemical strategy for the large

Structural and optical characterization of oxygenated CdTe/Sm3+ in sol-gel silica glasses

International Nuclear Information System (INIS)

Mathew, Siby; Rejikumar, P.R.; Adiyodi, Amrutha K.; Jyothy, P.V.; Unnikrishnan, N.V.

2008-01-01

Oxygenated cadmium telluride co-doped with rare earth element samarium is prepared by sol-gel method. Sample is air annealed at 200, 500 and 800 deg. C. The absorption and fluorescence spectra are analysed using Judd-Ofelt analysis to obtain J-O parameters. X-ray spectroscopy analysis shows the presence of thermally grown CdTeO 3 phase developed at the expense of CdTe phase on heat treatment for samples annealed at 800 deg. C. The FT-IR spectrum of the sample is taken at different annealing temperatures and the assignments of the absorption bands are compiled which shows the gradual evolution of the rigid glassy network formed. Enhanced fluorescence from air annealed Co-doped samples are also investigated

The ternary systems Sc-Sm(Dy)-Si at 870 K

International Nuclear Information System (INIS)

Kotur, B.Ya.; Mokra, I.Ya.; Toporinskij, A.Ya.

1991-01-01

Isothermal cross sections of the ternary systems Sc-Sm-Si and Sc-Dy-Si at 870 K have been plotted. Investigation of scandium and disprosium in ternary systems have been examined by X-ray diffraction and microstructure analysis. Besides literary data on binary systems Sc-Si, Sm-Si, Dy-Si have been used. Formation of limited (Sc-Sm-Si, Sc-Dy-Si) and continuous (Sc-Dy-Si) solid solutions based on bisilicides of Sc and Sm(Dy) is discovered. Two and five ternary compounds in Sc-Sm-Si and Sc-Dy-Si systems have been determined and their crystal structure has been established. When investigating of Sc-(rare earth element)-Si ternary systems and should take into account the specific interaction of scandium and samarium with REE

Análise de pesticidas, aflatoxinas e análise de macro e microminerais de polpa cítrica peletizada comercial

Directory of Open Access Journals (Sweden)

N.J.F. Oliveira

2004-10-01

Full Text Available Pesticides, aflatoxins, and nutritional analyses of commercial citrus pulp pellets in Brazil were performed in samples from São Paulo State. They were stored during 86 days and were processed for detection of toxic agents. Residual pesticides (organochlorinated, organophosphorus, pyrethoids, carbamates, chloroalquil tio fungicides, triazols, and the miscellaneous compound propargit and aflatoxins (B1, B2, G1 and G2 were assayed at 0, 43 and 86 days of storage. It was not detected residual pesticide and aflatoxins in any sample. The analysis indicated reduced levels of phosphorous and high values of calcium. Assessment of micro minerals indicated the presence of aluminum, barium, titanium, cooper, manganese, thorium, vanadium, zinc, lanthanum, samarium, cobalt, antimony, arsenic, and scandium.

Structural and spectral properties of MgZnO2:Sm3+ phosphor

Science.gov (United States)

Rajput, Preasha; Sharma, Pallavi; Biswas, Pankaj; Kamni

2018-05-01

The samarium doped MgZnO2 phosphor was synthesized by the low-cost combustion method. The powder X-ray diffraction (XRD) analysis confirmed the crystallinity and phase purity of the phosphor. The lattice parameters were determined by indexing the diffraction peaks. The photoluminescence (PL) study revealed that the phosphor exhibited a broad excitation band in the UV region ranging between 200 to 350 nm. The 601 nm emission was ascribed to 4G5/2 to 6H7/2 transitions of the Sm3+ ion. The optical bandgap of MgZnO2:Sm3+ was obtained to be 3.56 eV. The phosphor can be projected as a useful material in X- and gamma-ray scintillators.

Observation and analysis of X-ray spectra of highly-ionized atoms produced by laser irradiation in the wavelength range 0.60 nm to 0.95 nm

International Nuclear Information System (INIS)

Wyart, J.-F.; Ecole Polytech., Palaiseau; Fajardo, M.; Missalla, T.; Gauthier, J.-C.; Chenais-Popovics, C.; Klopfel, D.; Uschmann, I.; Foerster, E.

1999-01-01

The spectra of highly-charged ions produced by laser irradiation on flat targets at about 5 x 10 14 Wcm -2 are recorded in the range from 0.60 nm to 0.95 nm (6 A to 9.5 A) by means of two spectrographs (a flat ADP crystal and a Johann SiO 2 crystal spectrograph). The identification of the lines is supported by calculations of energies and transition probabilities in the relativistic parametric potential model. New identifications in several spectra of iron (Fe XXIII to Fe XXI), sodium-like strontium, Sr XXVIII, magnesium-like indium. In XXXVIII, and cobalt-like samarium, Sm XXXVI, are given. In the case of Fe XXIII, relativistic and non-relativistic (Cowan) ab initio calculations are compared. (orig.)

Heat capacity of Dy6UO12(s)

International Nuclear Information System (INIS)

Sahu, M.; Nagara, B.K.; Saxena, M.K.; Dash, S.

2010-01-01

There is a need to improve the reactor performance through longer cycle length, which is being carried out by initial fuel enrichment. This additional fuel enrichment is being compensated by introduction of additional neutron absorber material called as burnable poison. Burnable poisons are materials having one or more isotopes which have high neutron absorption cross section and gets converted into other isotopes of relatively low absorption cross section. The use of burnable poison provides the necessary negative moderator reactivity coefficient at the beginning of core life and helps shape core power distribution. Usually rare-earth elements such as gadolinium, dysprosium and samarium have been applied for this purpose. Presently gadolinia doped urania is being used as burnable poison in boiling water reactor (BWR)

Trichloridotris{N-[phenyl(pyridin-2-ylmethylidene]hydroxylamine-κ2N,N′}samarium(III

Directory of Open Access Journals (Sweden)

Yahong Li

2012-03-01

Full Text Available The SmIII ion in the title compound, [SmCl3(C12H10N2O3], shows a coordination number of nine with a slightly distorted tricapped trigonal prismatic geometry based on a Cl3N6 donor set. The molecular structure is stabilized by three intramolecular O—H...Cl hydrogen bonds.

Electronic structure and magnetism of samarium and neodymium adatoms on free-standing graphene

Czech Academy of Sciences Publication Activity Database

Kozub, Agnieszka L.; Shick, Alexander; Máca, František; Kolorenč, Jindřich; Lichtenstein, A.I.

2016-01-01

Roč. 94, č. 12 (2016), 1-7, č. článku 125113. ISSN 2469-9950 R&D Projects: GA ČR GA15-07172S Institutional support: RVO:68378271 Keywords : graphen * rare-earth adatoms * density functional theory Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 3.836, year: 2016

Pyroelectric properties and electrical conductivity in samarium doped BiFeO 3 ceramics

KAUST Repository

Yao, Yingbang; Liu, Wenchao; Mak, C. L.

2012-01-01

. This electrical conduction was attributed to oxygen vacancy existing in the samples. An activation energy of ∼0.7 eV for the conduction process was found to be irrespective of the Sm 3+ doping level. On the other hand, the magnetic Néel temperature (T N) decreased

Preparation method and thermal properties of samarium and europium-doped alumino-phosphate glasses

Energy Technology Data Exchange (ETDEWEB)

Sava, B.A., E-mail: savabogdanalexandru@yahoo.com [National Institute of Research and Development for Optoelectronics, Department for Optospintronics, 409 Atomistilor Street, P.O. Box MG – 5, RO-77125 Magurele (Romania); Elisa, M., E-mail: astatin18@yahoo.com [National Institute of Research and Development for Optoelectronics, Department for Optospintronics, 409 Atomistilor Street, P.O. Box MG – 5, RO-77125 Magurele (Romania); Boroica, L., E-mail: boroica_lucica@yahoo.com [National Institute for Lasers, Plasma and Radiation Physics, 77125 Magurele (Romania); Monteiro, R.C.C., E-mail: rcm@fct.unl.pt [Center of Materials Research/Institute for Nanostructures, Nanomodelling and Nanofabrication, (CENIMAT/I3N), Department of Materials Sciences, Faculty of Sciences and Technology, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal)

2013-12-01

Highlights: • Improved preparation method of rare-earth-doped phosphate glasses was done. • Working and annealing temperatures were lower than for undoped phosphate glass. • Doped glass viscosity is also lower and has quasi-linear variation with temperature. • Exothermic peak appears at about 555 °C and 685 °C, due to devitrification in glass. -- Abstract: The present work investigates alumino-phosphate glasses from Li{sub 2}O–BaO–Al{sub 2}O{sub 3}–La{sub 2}O{sub 3}–P{sub 2}O{sub 5} system containing Sm{sup 3+} and Eu{sup 3+} ions, prepared by two different ways: a wet raw materials mixing route followed by evaporation and melt-quenching, and by remelting of shards. The linear thermal expansion coefficient measured by dilatometry is identical for both rare-earth-doped phosphate glasses. Comparatively to undoped phosphate glass the linear thermal expansion coefficient increases with 2 × 10{sup −7} K{sup −1} when dopants are added. The characteristic temperatures very slowly decrease but can be considered constant with atomic weight, atomic number and f electrons number of the doping ions in the case of T{sub g} (vitreous transition temperature) and T{sub sr} (high annealing temperature) but slowly increase in the case of T{sub ir} (low annealing temperature–strain point) and very slowly increase, being practically constant in the case of T{sub D} (dilatometric softening temperature). Comparatively to undoped phosphate glass the characteristic temperatures of Sm and Eu-doped glasses present lower values. The higher values of electrical conductance for both doped glasses, comparatively to usual soda-lime-silicate glass, indicate a slightly reduced stability against water. The viscosity measurements, showed a quasi-linear variation with temperature the mean square deviation (R{sup 2}) being ranged between 0.872% and 0.996%. The viscosity of doped glasses comparatively to the undoped one is lower at the same temperature. Thermogravimetric analysis did not show notable mass change for any of doped samples. DSC curves for both rare-earth-doped phosphate glasses, as bulk and powdered samples, showed T{sub g} values in the range 435–450 °C. Bulk samples exhibited a very weak exothermic peak at about 685 °C, while powdered samples showed two weak exothermic peaks at about 555 °C and 685 °C due to devitrification of the glasses. Using designed melting and annealing programs, the doped glasses were improved regarding bubbles and cords content and strain elimination.

Lanthanum lead boro-tellurite glasses doped with samarium trioxide for luminescent devices application

Science.gov (United States)

Madhu, A.; Eraiah, B.

2018-04-01

Boro-tellurite based glasses (10La2O3-(20-x) TeO2-30PbO-40B2O3-xSm2O3) (x = 0, 0.5, 1.0 and 2.0 mol %) doped with different concentrations of Sm3+ ions has been investigated. The optical properties have been studied through spectroscopic measurements such as absorption and luminescence. Absorption spectra reveals nine peaks due to 6H5/2→6P3/2, 4I3/2+4F5/2+4I11/2, 6F11/2, 6F9/2, 6F7/2, 6F5/2, 6F3/2, 6H15/2, and 6H13/2 transitions. Luminescence spectra under the excitation of 403 nm display four emission bands due to 4G5/2→6H5/2, 6H7/2, 6H9/2 and 6H11/2 transitions of Sm3+ ions. Among them 6H7/2 bright orange -red is more intense which proves that the present glasses are potential candidates for luminescent device applications in visible range as well as optical fibre communication since its refractive index is 1.65 high compared to other glasses.

Study on irradiation conditions of producing 153Sm with natural abundance samarium target

International Nuclear Information System (INIS)

Du Jin; Jin Xiaohai; Bai Hongsheng; Liu Yuemin; Chen Daming; Wang Fan

1998-01-01

Irradiation conditions of natural abundance 152 Sm targets in different forms are studied in the heavy water reactor and the light water swimming pool reactor at the China Institute of Atomic Energy. The result shows that the specific activity of 153 Sm in liquid form target irradiated in the light water swimming pool reactor is two times greater than that in solid form target. The radionuclide purity of 153 Sm is more than 99%, which can meet the needs of clinical application

Laser resonant ionization spectroscopy and laser-induced resonant fluorescence spectra of samarium atom

International Nuclear Information System (INIS)

Jin, Changtai

1995-01-01

We have measured new high-lying levels of Sm atom by two-colour resonant photoionisation spectroscopy; we have observed the isotope shifts of Sm atom by laser-induced resonant fluorescence spectroscopy; the lifetime of eight low-lying levels of Sm atom were measured by using pulsed laser-Boxcar technique in atomic beam.

Study of Optical and Structural Characteristics of Ceria Nanoparticles Doped with Negative and Positive Association Lanthanide Elements

Directory of Open Access Journals (Sweden)

N. Shehata

2014-01-01

Full Text Available This paper studies the effect of adding lanthanides with negative association energy, such as holmium and erbium, to ceria nanoparticles doped with positive association energy lanthanides, such as neodymium and samarium. That is what we called mixed doped ceria nanoparticles (MDC NPs. In MDC NPs of grain size range around 6 nm, it is proved qualitatively that the conversion rate from Ce4+ to Ce3+ is reduced, compared to ceria doped only with positive association energy lanthanides. There are many pieces of evidence which confirm the obtained conclusion. These indications are an increase in the allowed direct band gap which is calculated from the absorbance dispersion measurements, a decrease in the emitted fluorescence intensity, and an increase in the size of nanoparticles, which is measured using both techniques: transmission electron microscope (TEM and X-ray diffractometer (XRD. That gives a novel conclusion that there are some trivalent dopants, such as holmium and erbium, which can suppress Ce3+ ionization states in ceria and consequently act as scavengers for active O-vacancies in MDC. This promising concept can develop applications which depend on the defects in ceria such as biomedicine, electronic devices, and gas sensors.

Study of the low pressure (Black Phase) SmS properties

International Nuclear Information System (INIS)

Bordier, G.

1987-03-01

SmS has been studied for its transition from the low pressure black phase to the high pressure intermediate valence phase; but the black phase properties seem to be very rich. The variations which pressure of the low-temperature electronic transport properties show the existence of a semi-metallic phase within the black phase domain in a pressure-temperature diagram, for a pressure above 4 kbar, which corresponds to the so-called B'phase. We study the insulating low pressure phase with a model involving acceptor like states. Using electronic paramagnetic resonance experiments we observe a square symmetry trivalent samarium ion neighbour of a sulfure defect, and magnetically coupled with the lattice. This defect exists in two nearly symmetric configurations and the resonance line broadens with temperature in an actived way. It gives rise to metastable effects yielding conductivity relaxations, analysed with stretched exponential laws, because the defect traps magnetically conduction electrons forming a bound magnetic polaron. The relaxation time at zero field is temperature actived. We develop a phenomenological model that gives the good orders of magnitude for the trapping barrier and for the critical field corresponding to the maximum of the low temperature magnetoresistance [fr

Thermochemistry of selected lanthanide and actinide hydroxycarbonates and carbonates

International Nuclear Information System (INIS)

Merli, L.; Fuger, J.

1996-01-01

Lanthanide and actinide carbonates and hydroxycarbonates are, together with the hydroxides, important compounds in the problematics of high level waste disposal, since such and related compounds may appear as solid phases as a result of the interaction of the waste with natural waters. Experimental results on the stability and relationships between these compounds, particularly the hydroxycarbonates, are relatively fragmentary and arise mainly from solubility measurements, and, to a lesser extent, from enthalpy of formation determinations. We report here the enthalpies of formation of a number of well characterized hydroxycarbonates of trivalent lanthanides, namely those of neodymium, samarium, dysprosium, ytterbium, and of americium, as well as that of neodymium sesquicarbonate, using solution calorimetry in acidic media. The obtained values are discussed in the light of literature data on existing solubility and enthalpy of formation of related compounds. Our results have been obtained with a newly conceived sealed calorimeter, briefly described in the paper, in which the CO 2 produced during the dissolution reaction is maintained in solution, thus eliminating the problem of the kinetically slow evolution of the CO 2 (g) from the medium and the irregularities in the associated thermal effect. (orig.)

X-ray induced Sm{sup 3+} to Sm{sup 2+} conversion in fluorophosphate and fluoroaluminate glasses for the monitoring of high-doses in microbeam radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Vahedi, Shahrzad; Okada, Go; Morrell, Brian; Muzar, Edward; Koughia, Cyril; Kasap, Safa [Department of Electrical and Computer Engineering, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5A9 (Canada); Edgar, Andy; Varoy, Chris [School of Chemical and Physical Sciences and MacDiarmid Institute, Victoria University of Wellington, Kelburn Parade (New Zealand); Belev, George; Wysokinski, Tomasz [Canadian Light Source, Inc., University of Saskatchewan, Saskatoon, Saskatchewan S7N 0X4 (Canada); Chapman, Dean [Department of Anatomy and Cell Biology, University of Saskatchewan, Saskatoon, Saskatchewan S7N 5E5 (Canada)

2012-10-01

Fluorophosphate and fluoroaluminate glasses doped with trivalent samarium were evaluated as sensors of x-ray radiation for microbeam radiation therapy at the Canadian Light Source using the conversion of trivalent Sm{sup 3+} to the divalent form Sm{sup 2+}. Both types of glasses show similar conversion rates and may be used as a linear sensor up to {approx}150 Gy and as a nonlinear sensor up to {approx}2400 Gy, where saturation is reached. Experiments with a multi-slit collimator show high spatial resolution of the conversion pattern; the pattern was acquired by a confocal fluorescence microscopy technique. The effects of previous x-ray exposure may be erased by annealing at temperatures exceeding the glass transition temperature T{sub g} while annealing at T{sub A} < T{sub g} enhances the Sm conversion. This enhancement is explained by a thermally stimulated relaxation of host glass ionic matrix surrounding x-ray induced Sm{sup 2+} ions. In addition, some of the Sm{sup 3+}-doped glasses were codoped with Eu{sup 2+}-ions but the results show that there is no marked improvement in the conversion efficiency by the introduction of Eu{sup 2+}.

Resorting the NIST undulator using simulated annealing for field error reduction

International Nuclear Information System (INIS)

Denbeaux, Greg; Johnson, Lewis E.; Madey, John M.J.

2000-01-01

We have used a simulated annealing algorithm to sort the samarium cobalt blocks and vanadium permendur poles in the hybrid NIST undulator to optimize the spectrum of the emitted light. While simulated annealing has proven highly effective in sorting of the SmCo blocks in pure REC undulators, the reliance on magnetically 'soft' poles operating near saturation to concentrate the flux in hybrid undulators introduces a pair of additional variables - the permeability and saturation induction of the poles - which limit the utility of the assumption of superposition on which most simulated annealing codes rely. Detailed magnetic measurements clearly demonstrated the failure of the superposition principle due to random variations in the permeability in the 'unsorted' NIST undulator. To deal with the issue, we measured both the magnetization of the REC blocks and the permeability of the NIST's integrated vanadium permendur poles, and implemented a sorting criteria which minimized the pole-to-pole variations in permeability to satisfy the criteria for realization of superposition on a nearest-neighbor basis. Though still imperfect, the computed spectrum of the radiation from the re-sorted and annealed NIST undulator is significantly superior to that of the original, unsorted device

Photon-activation therapy

International Nuclear Information System (INIS)

Fairchild, R.G.; Bond, V.P.

1982-01-01

Photon Activation Therapy (PAT) is a technique in which radiation dose to tumor is enhanced via introduction of stable 127 I in the form of iodinated deoxyuridine (IdUrd). Stimulation of cytotoxic effects from IdUrd is accomplished by activation with external (or implanted) radiation sources. Thus, accumulations of this nucleoside in actively competing cellpools do not preclude therapy in so far as such tissues can be excluded from the radiation field. Calculations show that 5% replacement of thymidine (Tyd) in tumor DNA should enhance the biological effectiveness of a given photon radiotherapy dose by a factor of approx. 3. Proportionally higher gains would result from higher replacements of Tyd and IdUrd. In addition, biological response is enhanced by chemical sensitization with IdUrd. The data indicate that damage from photon activation as well as chemical sensitization does not repair. Thus, at low dose rates, a further increase in therapeutic gain should accrue as normal tissues are allowed to repair and regenerate. A samarium-145 source has been developed for PAT, with activating x-ray energies of from 38 to 45 keV. Favorable clinical results can be expected through the use of IdUrd and protracted irradiations with low energy x-rays. In particular, PAT may provide unique advantages at selected sites such as brain, or head and neck tumors

Origin of Blue-Green Emission in α-Zn2P2O7 and Local Structure of Ln3+ Ion in α-Zn2P2O7:Ln3+ (Ln = Sm, Eu): Time-Resolved Photoluminescence, EXAFS, and DFT Measurements.

Science.gov (United States)

Gupta, Santosh Kumar; Ghosh, Partha Sarathi; Yadav, Ashok Kumar; Jha, Shambhu Nath; Bhattacharyya, Dibyendu; Kadam, Ramakant Mahadeo

2017-01-03

Considering the fact that pyrophosphate-based hosts are in high demand for making highly efficient luminescence materials, we doped two visible lanthanide ions, viz. Sm 3+ and Eu 3+ , in Zn 2 P 2 O 7 . Interestingly, it was oberved that pure Zn 2 P 2 O 7 displayed blue-green dual emission on irradiation with ultraviolet light. Emission and lifetime spectroscopy shows the presence of defects in pyrophosphate samples which are responsible for such emission. DFT calculations clearly pinpointed that the electronic transitions between defect states located at just below the conduction band minimum (arises due to V O 1+ and V O 2+ defects) and valence band maximum, as well as impurity states situated in the band gap, can lead to dual emission in the blue-green region, as is also indicated by emission and lifetime spectra. X-ray absorption near edge spectroscopy (XANES) shows the stabilization of europium as well as samarium ion in the +3 oxidation state in α-Zn 2 P 2 O 7 . The fact that α-Zn 2 P 2 O 7 has two different coordination numbers for zinc ions, i.e. five- and six-coordinate, the study of dopant ion distribution in this particular matrix will be an important step in realizing a highly efficient europium- and samarium-based red-emitting phosphor. Time resolved photoluminescence (TRPL) shows that both of these ions are heterogeneously distributed between five- and six-coordinated Zn 2+ sites and it is the six-coordinated Zn 2+ site which is the most favorable for lanthanide ion doping. Extended X-ray absorption fine structure (EXAFS) measurements also suggested that a six-coordinated zinc ion is the preferred site occupied by trivalent lanthanide ions, which is in complete agreement with TRPL results. It was observed that there is almost complete transfer of photon energy from Zn 2 P 2 O 7 to Eu 3+ , whereas this transfer is inefficient and almost incomplete in case of Sm 3+ , which is indeed important information for the realization of pyrophosphate

WE-H-207A-07: Image-Based Versus Atlas-Based Internal Dosimetry

Energy Technology Data Exchange (ETDEWEB)

Fallahpoor, M; Abbasi, M [Vali-Asr Hospital, School of Medicine, Tehran University of Medical Science, Tehran, Tehran (Iran, Islamic Republic of); Parach, A [Shahid Sadoughi University of Medical Sciences, Yazd, Yazd (Iran, Islamic Republic of); Kalantari, F [UT Southwestern Medical Center, Dallas, TX (United States)

2016-06-15

Purpose: Monte Carlo (MC) simulation is known as the gold standard method for internal dosimetry. It requires radionuclide distribution from PET or SPECT and body structure from CT for accurate dose calculation. The manual or semi-automatic segmentation of organs from CT images is a major obstacle. The aim of this study is to compare the dosimetry results based on patient’s own CT and a digital humanoid phantom as an atlas with pre-specified organs. Methods: SPECT-CT images of a 50 year old woman who underwent bone pain palliation with Samarium-153 EDTMP for osseous metastases from breast cancer were used. The anatomical date and attenuation map were extracted from SPECT/CT and three XCAT digital phantoms with different BMIs (i.e. matched (38.8) and unmatched (35.5 and 36.7) with patient’s BMI that was 38.3). Segmentation of patient’s organs in CT image was performed using itk-SNAP software. GATE MC Simulator was used for dose calculation. Specific absorbed fractions (SAFs) and S-values were calculated for the segmented organs. Results: The differences between SAFs and S-values are high using different anatomical data and range from −13% to 39% for SAF values and −109% to 79% for S-values in different organs. In the spine, the clinically important target organ for Samarium Therapy, the differences in the S-values and SAF values are higher between XCAT phantom and CT when the phantom with identical BMI is employed (53.8% relative difference in S-value and 26.8% difference in SAF). However, the whole body dose values were the same between the calculations based on the CT and XCAT with different BMIs. Conclusion: The results indicated that atlas-based dosimetry using XCAT phantom even with matched BMI for patient leads to considerable errors as compared to image-based dosimetry that uses the patient’s own CT Patient-specific dosimetry using CT image is essential for accurate results.

Nuclear structure and heavy-ion fusion

International Nuclear Information System (INIS)

Stokstad, R.G.

1980-10-01

A series of lectures is presented on experimental studies of heavy-ion fusion reactions with emphasis on the role of nuclear structure in the fusion mechanism. The experiments considered are of three types: the fusion of lighter heavy ions at subcoulomb energies is studied with in-beam γ-ray techniques; the subbarrier fusion of 16 O and 40 Ar with the isotopes of samarium is detected out of beam by x-radiation from delayed activity; and measurements at very high energies, again for the lighter ions, employ direct particle identification of evaporation residues. The experimental data are compared with predictions based on the fusion of two spheres with the only degree of freedom being the separation of the centers, and which interact via potentials that vary smoothly with changes in the mass and charge of the projectile and target. The data exhibit with the isotopes of samarium, a portion of these deviations can be understood in terms of the changing deformation of the target nucleus, but an additional degree of freedom such as neck formation appears necessary. The results on 10 B + 16 O and 12 C + 14 N → 26 Al at high bombarding energies indicate a maximum limiting angular momentum characteristic of the compound nucleus. At lower energies the nuclear structure of the colliding ion seems to affect strongly the cross section for fusion. Measurements made at subbarrier energies for a variety of projectile-target combinations in the 1p and 2s - 1d shell also indicate that the valence nucleons can affect the energy dependence for fusion. About half the systems studied so far have structureless excitation functions which follow a standard prediction. The other half exhibit large variations from this prediction. The possible importance of neutron transfer is discussed. The two-center shell model appears as a promising approach for gaining a qualitative understanding of these phenomena. 95 references, 52 figures, 1 table

Radioisotopic synovectomy using ferric hydroxide macroaggregated for chronic arthritis treatment

International Nuclear Information System (INIS)

Lima, Carla Flavia; Campos, Tarcisio P.R.

2002-01-01

Synovectomy radioisotopic is an arthritis treatment used in specific clinical conditions whose main goal is to sterilized the synovia. This treatment has specific and precise indications and it is considered to have an adequate response. The present work presents a modeling of an articulation (joint) based on its real geometric anatomy and chemical constitution. The internal dosimetry is evaluated by the Monte Carlo Code. The majority of the radionuclides were considered in the simulations. The syntheses of the ferric hydroxide macroaggregates with dysprosium and samarium have been prepared (Dy 165 -MHF and Sm 153 -MHF). Obtaining the cintilographic images of rabbits in which Dy 165 -MHF is injected is in progress. Biodistribution studies in addition with the internal dosimetry will certify the dose in the membrane of the synovia. (author)

Spectroscopic identification of rare earth elements in phosphate glass

Science.gov (United States)

Devangad, Praveen; Tamboli, Maktum; Muhammed Shameem, K. M.; Nayak, Rajesh; Patil, Ajeetkumar; Unnikrishnan, V. K.; Santhosh, C.; Kumar, G. A.

2018-01-01

In this work, rare earth-doped phosphate glasses were synthesized and characterized using three different spectroscopic techniques. The absorption spectra of the prepared praseodymium (Pr) and samarium (Sm) doped glasses, recorded by a UV-VIS-NIR spectrophotometer, show the characteristic absorption bands of these elements. To confirm this inference, laser-induced fluorescence spectra of Pr and Sm were obtained at a laser excitation of 442 nm. Their emission bands are reported here. The elemental analysis of these samples was carried out using a laser-induced breakdown spectroscopy (LIBS) system. Characteristic emission lines of Pr and Sm have been identified and reported by the recorded LIBS spectra of glass samples. Results prove that using these three complimentary spectroscopic techniques (absorption, fluorescence and LIBS), we can meaningfully characterize rare earth-doped glass samples.

Chemical characterization of gas- and oil-bearing shales by instrumental neutron activation analysis

Science.gov (United States)

Frost, J.K.; Koszykowski, R.F.; Klemm, R.C.

1982-01-01

The concentration of As, Ba, Ca, Co, Cr, Cs, Dy, Eu, Fe, Ga, Hf, K, La, Lu, Mn, Mo, Na, Ni, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, U, Yb, and Zn were determined by instrumental neutron activation analysis in block shale samples of the New Albany Group (Devonian-Mississippian) in the in the Illinois Basin. Uranium content of the samples was as high as 75 ppm and interfered in the determination of samarium, molybdenum, barium and cerium. In the determination of selenium a correction was made for interference from tantalum. U, As, Co, Mo, Ni and Sb as well as Cu, V and pyritic sulphur which were determined by other methods, were found to correlate positively with the organic carbon content of the samples. ?? 1982 Akade??miai Kiado??.

Advanced-technology 30-cm-diameter mercury ion thruster

Science.gov (United States)

Beattie, J. R.; Kami, S.

1982-01-01

An advanced-technology mercury ion thruster designed for operation at high thrust and high thrust-to-power ratio is described. The laboratory-model thruster employs a highly efficient discharge-chamber design that uses high-field-strength samarium-cobalt magnets arranged in a ring-cusp configuration. Ion extraction is achieved using an advanced three-grid ion-optics assembly which utilizes flexible mounts for supporting the screen, accel, and decel electrodes. Performance results are presented for operation at beam currents in the range from 1 to 5 A. The baseline specific discharge power is shown to be about 125 eV/ion, and the acceptable range of net-to-total accelerating-voltage ratio is shown to be in the range of 0.2-0.8 for beam currents in the range of 1-5 A.

X-ray fluorescence analysis of neodymium oxide/oxalate for rare earth impurities

International Nuclear Information System (INIS)

Chandola, L.C.; Mohile, A.N.

1977-01-01

An X-ray fluorescence method for the determination of cesium, praseodymium, samarium, europium and gadolinium in pure neodymium oxide and oxalate is described. The oxide sample is converted to oxalate and mixed with a binder (boric acid) to obtain a pressed circular pellet. The amount of sample needed for analysis is reduced by making use of the double layer pellet technique. A tungsten target X-ray tube is employed to irradiate the sample and a Philips PW 1220 semiautomatic X-ray spectrometer with a LiF (200) crystal is used to analyse the fluorescent X-rays. The minimum determination limit is 0.01 percent for all rare earths determined except for europium for which the limit is 0.005 percent. Three sigma detection limits have been calculated. (author)

Radiological Hazard of Spallation Products in Accelerator-Driven System

International Nuclear Information System (INIS)

Saito, M.; Stankovskii, A.; Artisyuk, V.; Korovin, Yu.; Shmelev, A.; Titarenko, Yu.

2002-01-01

The central issue underlying this paper is related to elucidating the hazard of radioactive spallation products that might be an important factor affecting the design option of accelerator-driven systems (ADSs). Hazard analysis based on the concept of Annual Limit on Intake identifies alpha-emitting isotopes of rare earths (REs) (dysprosium, gadolinium, and samarium) as the dominant contributors to the overall toxicity of traditional (W, Pb, Pb-Bi) targets. The matter is addressed from several points of view: code validation to simulate their yields, choice of material for the neutron producing targets, and challenging the beam type. The paper quantitatively determines the domain in which the toxicity of REs exceeds that of polonium activation products broadly discussed now in connection with advertising lead-bismuth technology for the needs of ADSs

Recoverable immobilization of transuranic elements in sulfate ash

Science.gov (United States)

Greenhalgh, Wilbur O.

1985-01-01

Disclosed is a method of reversibly immobilizing sulfate ash at least about 20% of which is sulfates of transuranic elements. The ash is mixed with a metal which can be aluminum, cerium, samarium, europium, or a mixture thereof, in amounts sufficient to form an alloy with the transuranic elements, plus an additional amount to reduce the transuranic element sulfates to elemental form. Also added to the ash is a fluxing agent in an amount sufficient to lower the percentage of the transuranic element sulfates to about 1% to about 10%. The mixture of the ash, metal, and fluxing agent is heated to a temperature sufficient to melt the fluxing agent and the metal. The mixture is then cooled and the alloy is separated from the remainder of the mixture.

Simultaneous Patterning of Independent Metal/Metal Oxide Multi-Layer Films Using Two-Tone Photo-Acid Generating Compound Systems

Directory of Open Access Journals (Sweden)

Hideo Honma

2012-10-01

Full Text Available (1 The photo-induced solubility and positive-tone direct photo-patterning of iron, copper and lanthanides chelated with 4-(2-nitrobenzyloxycarbonylcatechol (NBOC or 4-(6-nitroveratryloxycarbonylcatechol (NVOC was investigated. Photo-patterning of iron, copper, cerium, samarium, europium, terbium, dysprosium, holmium, erbium and lutetium complexes was accomplished. Continuous films were formed by the pyrolysis of metal complex films at 500 °C. (2 Based on the difference in the photo-reaction excitation wavelength profile of NBOC and NVOC complexes, a short and simple method for simultaneous micro-patterning of two independent films on each side of a transparent glass substrate was developed. Using the developed procedure, indium tin oxide and/or titanium oxide films were formed on each side of a quartz substrate without use of resist or etching.

Coprecipitation experiment with Sm hydroxide using a multitracer produced by nuclear spallation reaction: A tool for chemical studies with superheavy elements

International Nuclear Information System (INIS)

Kasamatsu, Yoshitaka; Yokokita, Takuya; Toyomura, Keigo; Shigekawa, Yudai; Haba, Hiromitsu; Kanaya, Jumpei; Huang, Minghui; Ezaki, Yutaka; Yoshimura, Takashi; Morita, Kosuke; Shinohara, Atsushi

2016-01-01

To establish a new methodology for superheavy element chemistry, the coprecipitation behaviors of 34 elements with samarium hydroxide were investigated using multitracer produced by a spallation of Ta. The chemical reactions were rapidly equilibrated within 10 s for many elements. In addition, these elements exhibited individual coprecipitation behaviors, and the behaviors were qualitatively related to their hydroxide precipitation behaviors. It was demonstrated that the ammine and hydroxide complex formations of superheavy elements could be investigated using the established method. - Highlights: • We established a new methodology for superheavy element (SHE) chemistry. • Coprecipitation behaviors of 34 elements with Sm hydroxide could be simultaneously investigated by using multitracer. • The complex formations were investigated from the coprecipitation behaviors. • The established method will lead to the study on various precipitates of SHEs.

Radioluminescence of rare-earth doped aluminum oxide

Energy Technology Data Exchange (ETDEWEB)

Santiago, M.; Molina, P. [Universidad Nacional del Centro de la Provincia de Buenos Aires, Instituto de Fisica Arroyo Seco, Pinto 399, 7000 Tandil (Argentina); Barros, V. S.; Khoury, H. J.; Elihimas, D. R., E-mail: msantiag@exa.unicen.edu.ar [Universidade Federal de Pernambuco, Departamento de Energia Nuclear, Av. Prof. Luiz Freire 1000, Recife, PE 50740-540 (Brazil)

2011-10-15

Carbon-doped aluminum oxide (Al{sub 2}O{sub 3}:C) is one of the most used radioluminescence (Rl) materials for fiberoptic dosimetry due to its high efficiency and commercial availability. However, this compound presents the drawback of emitting in the spectral region, where the spurious radioluminescence of fibers is also important. In this work, the radioluminescence response of rare-earth doped Al{sub 2}O{sub 3} samples has been evaluated. The samples were prepared by mixing stoichiometric amounts of aluminum nitrate, urea and dopants with different amounts of terbium, samarium, cerium and thulium nitrates varying from 0 to 0.15 mo 1%. The influence of the different activators on the Rl spectra has been investigated in order to determine the feasibility of using these compounds for Rl fiberoptic dosimetry. (Author)

Radioluminescence of rare-earth doped aluminum oxide

International Nuclear Information System (INIS)

Santiago, M.; Molina, P.; Barros, V. S.; Khoury, H. J.; Elihimas, D. R.

2011-10-01

Carbon-doped aluminum oxide (Al 2 O 3 :C) is one of the most used radioluminescence (Rl) materials for fiberoptic dosimetry due to its high efficiency and commercial availability. However, this compound presents the drawback of emitting in the spectral region, where the spurious radioluminescence of fibers is also important. In this work, the radioluminescence response of rare-earth doped Al 2 O 3 samples has been evaluated. The samples were prepared by mixing stoichiometric amounts of aluminum nitrate, urea and dopants with different amounts of terbium, samarium, cerium and thulium nitrates varying from 0 to 0.15 mo 1%. The influence of the different activators on the Rl spectra has been investigated in order to determine the feasibility of using these compounds for Rl fiberoptic dosimetry. (Author)

Effect of lanthanide on the microstructure and structure of LnMn0.5Fe0.5O3 nanoparticles with Ln=La, Pr, Nd, Sm and Gd prepared by the polymer precursor method

International Nuclear Information System (INIS)

Romero, Mariano; Faccio, Ricardo; Martínez, Javier; Pardo, Helena; Montenegro, Benjamín; Plá Cid, Cristiani Campos; Pasa, André A.

2015-01-01

The synthesis of LnMn 0.5 Fe 0.5 O 3 perovskite nanoparticles by the polymer precursor method showed a strong intrinsic dependence with different lanthanides (Ln=La, Pr, Nd, Sm and Gd). The polymerization level reached in the polymer precursor was proportional to the atomic number of lanthanide with exception of samarium, which showed the formation of a different precursor based in a citrate chelate with ethyleneglycol bonded as adduct. The increasing level of polymerization of the polymer precursors showed the formation of large-size perovskite nanoparticles after its calcination. SAXS and TEM analyses suggested that nanoparticles obtained, using this method, have a squared-like microstructure in connection with the polymer precursor microstructure. Structural analysis showed an orthorhombic structure with a slight decline in the Jahn–Teller distortion when the atomic number of lanthanide increases. Mössbauer spectroscopy showed the presence of a majority site in agreement with the Pbnm orthorhombic structure best fitted with Rietveld refinements and in some cases, a more distorted site attributed to local inhomogeneities and oxygen vacancies. - Highlights: • Precursor polymerization level is lower in the presence of lighter lanthanides. • Lighter lanthanide perovskite nanoparticles after calcination are lower-sized. • Nanoparticles obtained by this method have lamellae microstructure. • Jahn–Teller distortion declines for heavier lanthanide perovskites. • Oxygen vacancy phase was observed in lighter lanthanide perovskites

Nuclear and solid state investigations for the non-cubic paramagnetic system europium in samarium

International Nuclear Information System (INIS)

Boehm, R.

1979-01-01

By means of the time-differential perturbed angular gamma distribution after a nuclear reaction (TDPAD) the g-values of the isomer 1 1/2 - states are measured in 145 Eu and 147 Eu in the host metal Sm. The results are g ( 145 Eu) = + 1.356 + 0.008 g ( 147 Eu) = + 1.28 +- 0.01. The temperature dependence of the paramagnetic correction β obeys a Curie-Weiss law β = 1 + C/CT-, with C = -(50 +- 2) K and THETA = -(29 +- 5) K between 90 K and 1000 K, for both systems, 145 EU Sm and 147 Eu Sm. For room temperature the quadrupole coupling constant νsub(Q) is determined for 145 Eu Sm for the 1 1/2 - state: νsub(Q) = (12.5 +- 0.5) MHz and the paramagnetic relaxation time tausub(p) >= 1 μs. The g values are investigated also theoretically. (BHO)

Comparison of xenon-135 and samarium-149 poisoning in the Miniature Neutron Source Reactor

International Nuclear Information System (INIS)

Khattab, K.

2005-05-01

The Xe-135 equilibrium reactivity was calculated previously using the WIMSD4 and CITATION codes to estimate the fission product poisoning factor in the Syrian Miniature Neutron Source Reactor (MNSR). The fission product poisoning factor was used to calculate the Xe-135 concentrations and reactivities during the reactor operation, at saturation, and after shutdown. The fission product poisoning factor is used in this study to calculate the Sm-149 concentrations and reactivities during the reactor operation, at saturation, and after shutdown. The results are compared with Xe-135 concentrations and reactivities which were calculated before. The Xe-135 concentration increases versus the reactor operation time and reaches 2.836*10 13 atoms/cm 3 after 6 hours, where the Sm-149 concentration reaches 0.745*10 12 atoms/cm 3 . The Xe-135 and Sm-149 reactivities reach -0.451 and -0.256*10 -3 mk respectively after 6 hours of the reactor operation time. It is found that the Xe-135 and Sm-149 reactivities do not reach the equilibrium reactivities during typical reactor daily operating time. The Xe-235 concentration and reactivity are increased and reach to maximum values after 30000 second from the reactor shut down. Its maximum reactivity is -0.903 mk. Hence, the Xe-235 generates -0.452 mk extra reactivity after the reactor shutdown. The Sm-149 concentration and reactivates are increased after the reactor shut down. The Sm-149 reactivity reaches -0.249*10 -2 mk after 100000 second from the reactor shut down, and the Sm-149 introduces -2.231*10 -3 mk extra reactivity after the reactor shut down. Finally, the amount of Sm-149 accumulated in the reactor core after 1, 2, 5, and 10 years of the reactor operation time are: 3.995*10 -3 , 7.694*10 -3 , 17.226*10 -3 , and 2.892*10 -2 grams respectively. (Author)

Complexes of lanthanum(III), cerium(III), samarium(III) and dysprosium(III) with substituted piperidines

Energy Technology Data Exchange (ETDEWEB)

Manhas, B S; Trikha, A K; Singh, H; Chander, M

1983-11-01

Complexes of the general formulae M/sub 2/Cl/sub 6/(L)/sub 3/.C/sub 2/H/sub 5/OH and M/sub 2/(NO/sub 3/)/sub 6/(L)/sub 2/.CH/sub 3/OH have been synthesised by the reactions of chlorides and nitrates of La(III), Ce(III), Sm(III) and Dy(III) with 2-methylpiperidine, 3-methylpiperidine and 4-methylpiperidine. These complexes have been characterised on the basis of their elemental analysis, and IR and electronic reflectance spectra. IR spectral data indicate the presence of coordinated ethanol and methanol molecules and bidentate nitrate groups. Coordination numbers of the metal ions vary from 5 to 8. 19 refs.

153Sm-HM for arthritic knee pain. Estimated dosimetry

International Nuclear Information System (INIS)

Hardy-Pérez, Alberto E.; Torres-García, Eugenio; Mitsoura, Eleni; Jiménez-Mancilla, Nallely P.; Arteaga-de-Murphy, Consuelo; Pedraza-López, Martha

2012-01-01

Osteoarthritis is the most common type of arthropathy and after cardiovascular diseases is the most disabling disease in developing countries. The dosimetry for the clinical application of 153-samarium-hydroxymacroaggregates ( 153 Sm-HM) for radiation synovectomy (RSV) and palliative treatment for arthritic pain, as far as we know, has not been reported. The aim of this research was to estimate the radiation dose necessary for synovial ablation and pain palliation with minimum risk to the patient. 153 Sm-HM (370 MBq) was administered intra-articularly in a patient with severe knee pain and hindered motility. Regions of interest drawn on sequential, conjugated, anterior and posterior scintigraphy images were used to obtain the respective activity. The data was entered into a knee joint histological-geometric model designed with micrometric dimensions to represent the synovial cell layers. The Monte Carlo code was used to calculate the absorbed dose in each of the 12 model-cells representing the distance from the synovial liquid to the cartilage or bone. The absorbed dose in the synovial cavity was 114 Gy which is sufficient energy for RSV. The treated patient referred little pain and higher motility with no adverse reactions. 153 Sm-HM is a potentially valid radiopharmaceutical for RSV, which effectively palliates knee pain.

Control of oxygen vacancies and Ce+3 concentrations in doped ceria nanoparticles via the selection of lanthanide element

International Nuclear Information System (INIS)

Shehata, N.; Meehan, K.; Hudait, M.; Jain, N.

2012-01-01

The effect of lanthanides that have positive association energies with oxygen vacancies, such as samarium and neodymium, and the elements with negative association energies, such as holmium and erbium, on ionization state of cerium and, consequentially, the oxygen vacancy concentration in doped ceria nanoparticles are investigated in this article. Structural and optical characterizations of the doped and undoped ceria nanoparticles, synthesized using chemical precipitation, are carried out using transmission electron microscopy, X-ray diffractometry, optical absorption spectroscopy, and fluorescence spectroscopy. It is deduced that the negative association energy dopants decrease the conversion of Ce +4 into Ce +3 and, hence, scavenge the oxygen vacancies, evidenced by the observed increase in the allowed direct bandgap, decrease in the integrated fluorescence intensity, and increased the size of doped nanoparticles. The opposite trends are obtained when the positive association dopants are used. It is concluded that the determining factor as to whether a lanthanide dopant in ceria acts as a generator or scavenger of oxygen vacancies in ceria nanoparticles is the sign of the association energy between the element and the oxygen vacancies. The ability to tailor the ionization state of cerium and the oxygen vacancy concentration in ceria has applications in a broad range of fields, which include catalysis, biomedicine, electronics, and environmental sensing.

(18)O(2) label mechanism of sulfur generation and characterization in properties over mesoporous Sm-based sorbents for hot coal gas desulfurization.

Science.gov (United States)

Liu, B S; Wan, Z Y; Wang, F; Zhan, Y P; Tian, M; Cheung, A S C

2014-02-28

Using a sol-gel method, SmMeOx/MCM-41 or SBA-15 (Me=Fe, Co and Zn) and corresponding unsupported sorbents were prepared. The desulfurization performance of these sorbents was evaluated over a fixed-bed reactor and the effects of reaction temperature, feed and sorbent composition on desulfurization performance were studied. Samarium-based sorbents used to remove H2S from hot coal gas were reported for the first time. The results of successive sulfidation/regeneration cycles revealed that SmFeO3/SBA-15 sorbent was suitable for desulfurization of hot coal gas in the chemical industry. The formation of elemental sulfur during both sulfidation and regeneration processes depended strongly on the catalytic action of Sm2O2S species, which was confirmed for the first time via high sensitive time of flight mass spectrometer (TOF-MS) using 6%vol(18)O2/Ar regeneration gas and can reduce markedly procedural complexity. The sorbents were characterized using N2-adsorption, high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), temperature-programmed reduction of H2 (H2-TPR), thermogravimetry (TG) and time-of-flight mass spectrometry (TOF-MS) techniques. Copyright © 2014 Elsevier B.V. All rights reserved.

Giant magneto resistance and temperature coefficient of resistance in Sm0.55Sr0.30Ag0.15MnO3 perovskite

Directory of Open Access Journals (Sweden)

Masroor Ahmad Bhat

2016-12-01

Full Text Available Silver ions substituted samarium strontium manganite (Sm0.55Sr0.30Ag0.15MnO3 pervoskite was synthesized by using respective oxides in stoichiometric ratio through solid state reaction. The as-prepared sample was characterized by various analytical techniques to confirm its formation and understand the effect of monovalent silver ions in pervoskite lattice. X-ray diffraction pattern confirms the single phase formation while grain morphology in SEM image indicates good connectivity among the grains. The enhancement in metal to insulator transition temperature shows quenched disorder and magnetoresistance phenomena. The magnetoresistance (MR and temperature coefficient of resistance (TCR emerge from grain growth factor and homogeneity induced by Ag+ ions in the lattice. The reduction in hysteresis loss resulted from antiferromagnetic - ferromagnetic (TN and ferromagnetic - paramagnetic (Tc transitions reveals the removal of disorder in perovskite lattice by Ag+ ions substitution. This increases the magnetic moment across distinct ions on the applying magnetic field. The rise in MR% (~99% with silver doping emerging from smooth spin tunneling of the grains across the boundary and suppression of the disordered magnetic fluctuations with increase in magnetic field has been reported. The present compound exhibits the first order nature of magnetism and observed first time the highest value of TCR ~ 95%.

A model for nuclear research reactor dynamics

Energy Technology Data Exchange (ETDEWEB)

Barati, Ramin, E-mail: Barati.ramin@aut.ac.ir; Setayeshi, Saeed, E-mail: setayesh@aut.ac.ir

2013-09-15

Highlights: • A thirty-fourth order model is used to simulate the dynamics of a research reactor. • We consider delayed neutrons fraction as a function of time. • Variable fuel and temperature reactivity coefficients are used. • WIMS, BORGES and CITVAP codes are used for initial condition calculations. • Results are in agreement with experimental data rather than common codes. -- Abstract: In this paper, a useful thirty-fourth order model is presented to simulate the kinetics and dynamics of a research reactor core. The model considers relevant physical phenomena that govern the core such as reactor kinetics, reactivity feedbacks due to coolant and fuel temperatures (Doppler effects) with variable reactivity coefficients, xenon, samarium, boron concentration, fuel burn up and thermal hydraulics. WIMS and CITVAP codes are used to extract neutron cross sections and calculate the initial neuron flux respectively. The purpose is to present a model with results similar to reality as much as possible with reducing common simplifications in reactor modeling to be used in different analyses such as reactor control, functional reliability and safety. The model predictions are qualified by comparing with experimental data, detailed simulations of reactivity insertion transients, and steady state for Tehran research reactor reported in the literature and satisfactory results have been obtained.

Temperature quenching in LAB based liquid scintillator

Energy Technology Data Exchange (ETDEWEB)

Soerensen, A.; Zuber, K. [Technische Universitaet Dresden, Institute for Nuclear- and Particle Physics, Dresden (Germany); Hans, S.; Yeh, M. [Brookhaven National Laboratory, Chemistry Devision, Upton, NY (United States); Junghans, A.R.; Koegler, T.; Wagner, A. [Helmholtz-Zentrum Dresden-Rossendorf, Dresden (Germany); Krosigk, B. v. [Technische Universitaet Dresden, Institute for Nuclear- and Particle Physics, Dresden (Germany); University of British Columbia, Department of Physics and Astronomy, Vancouver, BC (Canada); Lozza, V. [Technische Universitaet Dresden, Institute for Nuclear- and Particle Physics, Dresden (Germany); Laboratorio de Instrumentacao e Fisica Experimental de Particulas, Lisboa (Portugal)

2018-01-15

The effect of temperature changes on the light output of LAB based liquid scintillator is investigated in a range from -5 to 30 C with α-particles and electrons in a small scale setup. Two PMTs observe the scintillator liquid inside a cylindrically shaped aluminum cuvette that is heated or cooled and the temperature dependent PMT sensitivity is monitored and corrected. The α-emitting isotopes in dissolved radon gas and in natural Samarium (bound to a LAB solution) excite the liquid scintillator mixtures and changes in light output with temperature variation are observed by fitting light output spectra. Furthermore, also changes in light output by compton electrons, which are generated from external calibration γ-ray sources, is analysed with varying temperature. Assuming a linear behaviour, a combined negative temperature coefficient of (-0.29 ± 0.01)%/ C is found. Considering hints for a particle type dependency, electrons show (-0.17 ± 0.02)%/ C, whereas the temperature dependency seems stronger for α-particles, with (-0.35 ± 0.03)%/ C. Due to a high sampling rate, a pulse shape analysis can be performed and shows an enhanced slow decay component at lower temperatures, pointing to reduced non-radiative triplet state de-excitations. (orig.)

Evaluation of genotoxic and cytotoxic effects of {sup 153} Sm-EDTMP in peripheral blood lymphocytes of bone metastasis patients; Avaliacao dos efeitos genotoxico e citotoxico do {sup 153} Sm-EDTMP em linfocitos perifericos de pacientes com metastase ossea

Energy Technology Data Exchange (ETDEWEB)

Suzuki, Miriam Fussae

2003-07-01

In this study the cellular damage in peripheral lymphocytes after exposure to {sup 153} Sm-EDTMP (Samarium-153 ethylene-diamine-tetramietylene-phosphonate) was determined using the technique of micronuclei analysis and differential coloration.{sup 153} Sm-EDTMP is a radiopharmaceutical used for pain relief in patients with bone metastases. The analysis of the frequency of micronuclei in patient blood samples obtained one hour after endovenous administration of radiopharmaceutical (41 MBq/kg) showed no statistical difference in relation to basal values in binucleated cells. However the analysis of damage distribution in mononucleated cells, showed that the patients without previous radiotherapy treatment presented a significant increase in the frequency of cells with one micronucleus and in those who had taken previous radiotherapy treatment, in cells with two or more micronuclei. The in vitro experiments conducted with the exposition of total blood to three radiation concentrations of {sup 153} Sm-EDTMP (0.370, 0.555 and 1.110 MBq/mL) during one hour showed an increase in the frequency of micronuclei and necrotic and apoptotic cells with increasing radiation dose. Dose-response curves for healthy donors and patients with bone metastasis without previous radiotherapy treatment were constructed. The comparison of the curves showed that patients presented higher radiosensitivity, either micronuclei or dead cell (necrotic or apoptotic) percentages, than healthy donors. (author)

Synthesis and characterization of Sm0.5Ba0.5MnO3-δ as anode materials for solid oxide fuel cells

International Nuclear Information System (INIS)

Abdalla, A. M.; Radenahmad, N.; Bakar, M. S. Abu; Petra, Pg M .I.; Azad, A. K.

2016-01-01

The material performance is a crucial issue in the current fuel cell technology, and for this reason we present this new series of Samarium family which can be used as electrode giving a high performance in a particular application. Sm 0 . 5 Ba 0 . 5 MnO 3-δ was prepared by solid state reaction method and characterized by using X-ray diffraction (XRD), and thermogravimetric analysis (TGA). Rietveld analysis of XRD data shows that the material has an Orthorhombic crystal structure with cell parameter a = 3.883(1) Å b = 3.8742(5) Å c = 7. 762(4) Å, in the Pmmm space group. TGA analyses shows that the materials is going to decrease by 0.32%. The density of the materials was calculated from structural refinement and found to be 8.372 gm/cm 3 . (paper)

Structural and electrical properties of Sm{sup 3+} substituted PZT ceramics

Energy Technology Data Exchange (ETDEWEB)

Pandey, S.K. [Solid State Physics Laboratory, Timarpur, Delhi 110 054 (India)], E-mail: 628@ssplnet.org; Thakur, O.P.; Bhattacharya, D.K. [Solid State Physics Laboratory, Timarpur, Delhi 110 054 (India); Prakash, Chandra [DRDO Bhawan, DHQ, New Delhi 110 011 (India); Chatterjee, Ratnamala [Department of Physics, Indian Institute of Technology, New Delhi 110 016 (India)

2009-01-22

Samarium modified lead zirconate titanate (PSZT: Pb{sub 1-x}Sm{sub x}(Zr{sub 0.65}Ti{sub 0.35})O{sub 3}: x = 0, 0.02, 0.04, 0.06) ceramics were synthesized by solid state ceramic route. XRD shows single-phase formation with rhombohedral structure up to x = 0.04. With Sm-substitution, the grain size first increases up to x = 0.02 and then decreases. A metal/ferroelectric/metal (MFM) structure was made by depositing gold electrode on the flat surfaces for electrical measurements. All samples show normal ferroelectric behaviour, however, a squareness of P-E loop (polarization vs. electric field) was observed to increase with Sm content. Higher electromechanical coupling coefficients (K{sub p} and K{sub t}) have been achieved for the PZT with 6 mol% Sm substitution and having fine grain size.

Synthesis and magnetic properties of SmOOH crystals

Energy Technology Data Exchange (ETDEWEB)

Samata, Hiroaki, E-mail: samata@maritime.kobe-u.ac.jp [Graduate School of Maritime Sciences, Kobe University, Fukaeminami, Higashinada, Kobe, Hyogo 658-0022 (Japan); Hanioka, Masashi [Graduate School of Maritime Sciences, Kobe University, Fukaeminami, Higashinada, Kobe, Hyogo 658-0022 (Japan); Ozawa, Tadashi C. [Materials Development Group, Superconducting Properties Unit, National Institute for Materials Science, Sengen, Tsukuba, Ibaraki 305-0047 (Japan)

2016-01-15

Samarium oxyhydroxide (SmOOH) crystals were synthesized using a flux method. The as-grown crystals were yellowish, transparent, and elongated with a maximum length of approximately 1.0 mm. SmOOH adopts a monoclinic structure in the space group P2{sub 1}/m with a=0.4356 nm, b=0.3766 nm, c=0.6139 nm, and β=108.464°. The magnetic susceptibility of the SmOOH crystals exhibited typical Van Vleck paramagnetism, and the experimental data at temperatures above 200 K were in close agreement with the calculated results using a spin-orbit coupling constant λ=443 K (308 cm{sup −1}). - Highlights: • SmOOH crystals were synthesized via flux method and characterized. • Magnetic susceptibilities above 200 K agreed with theoretical Van Vleck values. • Discrepancies were observed at lower temperatures based on the crystalline field.

Determination of trace elements in eyeshadow, face powder and rouge make-up cosmetics by neutron activation analysis

International Nuclear Information System (INIS)

Kanias, G.D.

1985-01-01

Some trace elements exist in cosmetics due to the mineral origin of their raw materials and there is no information about their concentration levels in these products. Instrumental neutron activation analysis was applied to determine the elements: cerium, cesium, europium, hafnium, lanthanum, lutetium, potassium, rubidium, samarium, scandium, sodium, tantalum, terbium, tungsten and ytterbium in eyeshadow, face powder and rouge make-up cosmetic products from the Greek market. According to the results, a wide range of values was found between the three examined cosmetics as well as between the different samples belonging to the same kind of cosmetics. This probably could be attributed to the various manufacturers of the analyzed samples. Moreover, the use of neutron activation analysis as a suitable routine method is discussed for the control of some elements which must not be contained in cosmetics. (author)

INFLUENCE OF SINTERING TEMPERATURE ON THE POLARIZATION RESISTANCE OF LaO20.6SrO20.4CoO20.2FeO20.8O3-δ - SDC CARBONATE COMPOSITE CATHODE

Directory of Open Access Journals (Sweden)

Nurul Akidah Baharuddin

2016-05-01

Full Text Available The effects of sintering temperature of an LSCF-samarium-doped ceria carbonate (SDCC cathode composite film on its polarization resistance (Rp were evaluated in this study. An LSCF-SDCC composite cathode was prepared for cathode film development by electrophoretic deposition (EPD. The LSCF-SDCC composite cathode was prepared at 50:50 weight percentage ratio. An EPD suspension which is based on an organic aqueous solution was used, and a mixture of ethanol and deionized water was used as medium with poly diallyl dimethyl ammonium chloride (PDADMAC as a dispersing agent. SDCC substrate was used, and EPD was performed on both sides. A symmetrical cell with cathode composite LSCF-SDCC films on both sides of the substrate was subjected to sintering at five different temperatures (from 550°C to 750°C. A symmetrical cell was painted using silver paste before undergoing electrochemical performance test (air condition, in which the impedance, Z data, was measured. The effects of sintering temperature change on element content and film porosity were first investigated by energy-dispersive X-ray spectroscopy, field emission scanning electron microscopy, and J-image analysis. Ceramic-based cathode LSCF-SDCC that was sintered at 600°C exhibited the lowest Rp at a value of 0.68 Ω when operated at 650°C. This study proved that EPD has potential in developing IT-LT solid oxide fuel cell cathode components with high electrochemical performance in terms of Rp values.

Study of toxicity of Samarium-153-EDTMP in the treatment of painful skeletal metastasis. Final report for the period 15 December 1996 - 14 December 1997

International Nuclear Information System (INIS)

Zhu Shoupeng

1998-02-01

Favourable characteristics of Sm-153 EDTMP make it an effective agent for use in the palliative treatment of metastatic bone pain. It has also been postulated that Sm-153 might have some tumoricidal effect. But until today its mechanism of action in the treatment of skeletal metastasis is not known. This experimental study has been designed to study the cellular and molecular changes occurring in the bone tumour cells (osteosarcoma of femur of wister rats) following irradiation with different doses of Sm-153 EDTMP. Experimental osteosarcorna tumour cells were harvested and treated with Sm-153 EDTMP over different periods of time ranging from 1-24 hours. Electron microscope, fluorescence microscope, MTI assay and 3 HTdR release assay studies were conducted to observe for effects of radiation. Sm-153 EDTMP irradiation of bone tumour cells resulted in significant nuclear fragmentation, margination of condensed chromatin, marked pyknosis and increased formation of membrane bounded apoptotic bodies formation. The quantification analysis of fragmented DNA for bone tumour cells induced by Sm-153 EDTMP showed that the DNA fragmentation was enhanced with prolongation of irradiation time. The inhibition rate of proliferation of bone tumour cells as well as DNA fragmentation in bone tumour cells after irradiation with Sm-153 EDTMP increased significantly and progressively with prolongation of irradiation time, reaching levels of 63% and 78% respectively by 24 hours. (author)

Mechanically induced strong red emission in samarium ions doped piezoelectric semiconductor CaZnOS for dynamic pressure sensing and imaging

Science.gov (United States)

Wang, Wei; Peng, Dengfeng; Zhang, Hanlu; Yang, Xiaohong; Pan, Caofeng

2017-07-01

Piezoelectric semiconductor with optical, electrical and mechanical multifunctions has great potential applications in future optoelectronic devices. The rich properties and applications mainly encompass the intrinsic structures and their coupling effects. Here, we report that lanthanide ions doped piezoelectric semiconductor CaZnOS:Sm3+ showing strong red emission induced by dynamic mechanical stress. Under moderate mechanical load, the doped piezoelectric semiconductor exhibits strong visible red emission to the naked eyes even under the day light. A flexible dynamic pressure sensor device is fabricated based on the prepared CaZnOS:Sm3+ powders. The mechanical-induced emission properties of the device are investigated by the optical fiber spectrometer. The linear characteristic emissions are attributed to the 4G5/2→6H5/2 (566 nm), 4G5/2→6H7/2 (580-632 nm), 4G5/2→6H9/2 (653-673 nm) and 4G5/2→6H11/2 (712-735 nm) f-f transitions of Sm3+ ions. The integral emission intensity is proportional to the value of applied pressure. By using the linear relationship between integrated emission intensity and the dynamic pressure, the real-time pressure distribution is visualized and recorded. Our results highlight that the incorporation of lanthanide luminescent ions into piezoelectric semiconductors as smart materials could be applied into the flexible mechanical-optical sensor device without additional auxiliary power, which has great potential for promising applications such as mapping of personalized handwriting, smart display, and human machine interface.

Needs and accuracy requirements for fission product nuclear data in the physics design of power reactor cores

International Nuclear Information System (INIS)

Rowlands, J.L.

1978-01-01

The fission product nuclear data accuracy requirements for fast and thermal reactor core performance predictions were reviewed by Tyror at the Bologna FPND Meeting. The status of the data was assessed at the Meeting and it was concluded that the requirements of thermal reactors were largely met, and the yield data requirements of fast reactors, but not the cross section requirements, were met. However, the World Request List for Nuclear Data (WRENDA) contains a number of requests for fission product capture cross sections in the energy range of interest for thermal reactors. Recent reports indicate that the fast reactor reactivity requirements might have been met by integral measurements made in zero power critical assemblies. However, there are requests for the differential cross sections of the individual isotopes to be determined in addition to the integral data requirements. The fast reactor requirements are reviewed, taking into account some more recent studies of the effects of fission products. The sodium void reactivity effect depends on the fission product cross sections in a different way to the fission product reactivity effect in a normal core. This requirement might call for different types of measurement. There is currently an interest in high burnup fuel cycles and alternative fuel cycles. These might require more accurate fission product data, data for individual isotopes and data for capture products. Recent calculations of the time dependence of fission product reactivity effects show that this is dependent upon the data set used and there are significant uncertainties. Some recent thermal reactor studies on approximations in the treatment of decay chains and the importance of xenon and samarium poisoning are also summarized. (author)

Rare-Earth-Rich Alloys; Alliages a Teneur Elevee en Terres Rares; Splavy, obogashchennye redkozemel'nymi ehlementami; Aleaciones Ricas en Tierras Raras

Energy Technology Data Exchange (ETDEWEB)

Copeland, M.; Kato, H. [Albany Metallurgy Research Center, Bureau of Mines, United States Department of the Interior, Albany, OR (United States)

1964-06-15

The rare earth metals with high thermal-neutron capture cross-sections are of interest for control of power-producing reactors; however, they are susceptible to corrosion. On the premise that non-rare earth metals may be alloyed with dysprosium, erbium, gadolinium and samarium, thus improving their properties, the effects of selected alloying additions on the rare earths were studied. The solubilities of the non-rare earth metals, zirconium, vanadium, chromium, iron, nickel, copper, aluminium and silicon, in dysprosium, erbium, gadolinium and samarium and their effects on the melting points, solid state transformations and corrosion properties were studied. -Phase diagrams were prepared up to the first rare earth-rich compound or eutectic, whichever occurred first. On completion of that portion of the work, alloys were made, heat-treated to yield maximum solid solubility of the non-rare earth alloying addition, and oxidation- and corrosion-tested. No improvement of the rare earth metals to oxidation resistance in the atmosphere was observed on alloying; in fact, most additions proved to be deleterious. Aluminium greatly improved the hot-Water corrosion resistance of the rare earths tested; other non-rare earth metal additions improved the resistance to a lesser degree. (author) [French] Les terres rares possedent une section efficace de capture des neutrons thermiques elevee; ces metaux presentent un grand interet pour le controle des reacteurs de puissance; toutefois, ils sont attaques par corrosion. En.partant de l'idee qu'il est possible d'allier des metaux autres que les terres rares avec le dysprosium, l 'erbium, le gadolinium et le samarium, et d'ameliorer ainsi leurs proprietes, les auteurs .ont observe les effets de l 'addition de certains metaux sur les terres rares. Ils ont etudie les solubilites du zirconium, du vanadium, du chrome; du fer, du nickel, du cuivre, de l'aluminium et du silicium dans le dysprosium, l'erbium, le gadolinium et le samarium

Dielectric behavior of samarium-doped BaZr0.2Ti0.8O3 ceramics

International Nuclear Information System (INIS)

Li, Yuanliang; Wang, Ranran; Ma, Xuegang; Li, Zhongqiu; Sang, Rongli; Qu, Yuanfang

2014-01-01

Graphical abstract: - Highlights: • We investigate dielectric properties and phase transition of Sm 3+ -doped BaZr 0.2 Ti 0.8 O 3 ceramics. • The additive amount of Sm 2 O 3 can greatly affect the dielectric properties. • The materials undergo a diffuse type ferroelectric phase transition. • There is an alternation of substitution preference of Sm 3+ ion for the host cations in perovskite lattice. - Abstract: The dielectric properties and phase transition of Sm 3+ -doped BaZr 0.2 Ti 0.8 O 3 (BZT20) ceramics were investigated. Room temperature X-ray diffraction study suggested that the compositions had single-phase cubic symmetry. Microstructure studies showed that the grain size decreased and that the Sm 2 O 3 amount markedly affected the dielectric properties of BZT20. A dielectric constant of 5700 at 0.2 mol% Sm 2 O 3 and a dissipation factor of only 0.0011 at 2 mol% Sm 2 O 3 were observed, indicating that BZT20 had significant potential applications. Moreover, the dielectric constant, dissipation factor, phase-transition temperature, and maximum dielectric constant increased with increased Sm 2 O 3 amount at ≤0.2 mol% Sm 2 O 3 but decreased with increased Sm 2 O 3 amount at >0.2 mol% Sm 2 O 3

Nanostructured Samarium Doped Fluorapatites and Their Catalytic Activity towards Synthesis of 1,2,4-Triazoles

Directory of Open Access Journals (Sweden)

Kranthi Kumar Gangu

2016-09-01

Full Text Available An investigation was conducted into the influence of the amino acids as organic modifiers in the facile synthesis of metal incorporated fluorapatites (FAp and their properties. The nanostructured Sm doped fluorapatites (Sm-FAp were prepared by a co-precipitation method using four different amino acids, namely glutamic acid, aspartic acid, glycine and histidine. The materials were characterized by various techniques including X-ray diffraction (XRD, Fourier transform infra-red spectroscopy (FT-IR, field emission scanning electron microscopy (FE-SEM, energy-dispersive X-ray spectroscopy (EDX, high resolution transmission electron microscopy (HR-TEM, N2-adsorption/desorption isotherm, temperature programmed desorption (TPD and fluorescence spectrophotometry. Under similar conditions, Sm-FAp prepared using different amino acids exhibited distinctly different morphological structures, surface area and pore properties. Their activity as catalysts was assessed and Sm-FAp/Glycine displayed excellent efficiency in the synthesis of 1,2,4-triazole catalyzing the reaction between 2-nitrobenzaldehyde and thiosemicarbazide with exceptional selectivity and 98% yield in a short time interval (10 min. The study provides an insight into the role of organic modifiers as controllers of nucleation, growth and aggregation which significantly influence the nature and activity of the catalytic sites on Sm-FAp. Sm-FAp could also have potential as photoactive material.

Influence of samarium ions (Sm3+) on the optical properties of lithium zinc phosphate glasses

Science.gov (United States)

Shwetha, M.; Eraiah, B.

2018-05-01

New glass samples with composition xSm2O3-(15-x) Li2O-45ZnO-40P2O5, where x= 0, 0.1, 0.3 and 0.5 mol % are prepared by conventional melt-quenching method. X-ray Diffraction measurements were performed to confirm their amorphous nature. Densities of these glasses were measured by Archimedes method. Optical properties were studied using optical absorption spectra which was recorded at room temperature in the UV-Vis region. Electronic transitions specific to the rare earth ion were observed from the UV-Visible spectroscopy. Optical direct band gap and indirect band gap energies were measured and their values were found to be between 4.23-4.74 eV and 3.02-3.67 eV, respectively. Refractive index has been measured with respect to different concentrations of Sm2O3. Polaron radius, inter-nuclear distance, field strength, dielectric constant and polarizability of oxide ions have been calculated. Fluorescence spectroscopy measurements have been performed by excitation in the UV-Visible range, which resulted in the significant fluorescence peaks. The luminescence color of the glass system has been characterized using Commission International de l'Eclairage de France 1931 chromaticity diagram.

Multi-factor analysis on events related to hematological toxicity in 153Sm-EDTMP palliative therapy for skeletal metastases

International Nuclear Information System (INIS)

Zhan Hongwei; Yu Xiaoling; Ye Xiaojuan; Bao Chengkan; Sun Da; He Gangqiang

2006-01-01

Objective: To investigate the clinical factors related to hematological toxicity induced by intravenous samarium-153 ethylenediaminetetramethylene phosphonic acid ( 153 Sm-EDTMP) treatment. Methods A total of 206 patients with bony metastases treated with 153 Sm-EDTMP were retrospectively analyzed. Logistic regression (SPSS 10.0 for Windows) and correlation analysis were used to evaluate the factors concerned. Results: Age of the patient, number of bone metastatic lesion, chemotherapy before 153 Sm-EDTMP therapy, concurrent radiotherapy and repeat-times of 153 Sm-EDTMP treatments were found the individual factors related to hematological toxicity. Chemotherapy before 153 Sm-EDTMP, concurrent radiotherapy, medication for normal blood counting and repeat-times of 153 Sm-EDTMP treatments were the hematological toxicity factors in multi-factor analysis. Conclusion: In 153 Sm-EDTMP therapy, several factors were found related to hematological toxicity suggesting more attention be paid to the change of blood cell counting after the palliative therapy. (authors)

Fundamentals of 3-D Neutron Kinetics and Current Status

International Nuclear Information System (INIS)

Aragones, J.M.

2008-01-01

This lecture includes the following topics: 1) A summary of the cell and lattice calculations used to generate the neutron reaction data for neutron kinetics, including the spectral and burnup calculations of LWR cells and fuel assembly lattices, and the main nodal kinetics parameters: mean neutron generation time and delayed neutron fraction; 2) the features of the advanced nodal methods for 3-D LWR core physics, including the treatment of partially inserted control rods, fuel assembly grids, fuel burnup and xenon and samarium transients, and excore detector responses, that are essential for core surveillance, axial offset control and operating transient analysis; 3) the advanced nodal methods for 3-D LWR core neutron kinetics (best estimate safety analysis, real-time simulation); and 4) example applications to 3-D neutron kinetics problems in transient analysis of PWR cores, including model, benchmark and operational transients without, or with simple, thermal-hydraulics feedback.

Rare earth doped M-type hexaferrites; ferromagnetic resonance and magnetization dynamics

Directory of Open Access Journals (Sweden)

Vipul Sharma

2018-05-01

Full Text Available M-type hexagonal barium ferrites come in the category of magnetic material that plays a key role in electromagnetic wave propagation in various microwave devices. Due to their large magnetic anisotropy and large magnetization, their operating frequency exceeds above 50 GHz. Doping is a way to vary its magnetic properties to such an extent that its ferromagnetic resonance (FMR response can be tuned over a broad frequency band. We have done a complete FMR study of rare earth elements neodymium (Nd and samarium (Sm, with cobalt (Co as base, doped hexaferrite nanoparticles (NPs. X-ray diffractometry, vibrating sample magnetometer (VSM, and ferromagnetic resonance (FMR techniques were used to characterize the microstructure and magnetic properties of doped hexaferrite nanoparticles. Using proper theoretical electromagnetic models, various parameters are extracted from FMR data which play important role in designing and fabricating high-frequency microwave devices.

Interpretation of Ferroan Anorthosite Ages and Implications for the Lunar Magma Ocean

Science.gov (United States)

Neal, C. R.; Draper, D. S.

2017-01-01

Ferroan Anorthosites (FANs) are considered to have purportedly crystallized directly from the lunar magma ocean (LMO) as a flotation crust. LMO modeling suggests that such anorthosites started to form only after greater than 70 percent of the LMO had crystallized. Recent age dates for FANs have questioned this hypothesis as they span too large of an age range. This means a younger age for the Moon-forming giant impact or the LMO hypothesis is flawed. However, FANs are notoriously difficult to age-date using the isochron method. We have proposed a mechanism for testing the LMO hypothesis through using plagioclase trace element abundances to calculate equilibrium liquids and compare them with LMO crystallization models. We now examine the petrography of the samples that have Sm-Nd (Samarium-Neodymium) age dates (Rb-Sr (Rubidium-Strontium) isotopic systematics may have been disturbed) and propose a relative way to age date FANs.

Calorimetric investigation on the Pb-Sm and Sn-Sm alloys

International Nuclear Information System (INIS)

Berrada, A.-E.-A.; Claire, Y.; Chafik el Idrissi, M.; Castanet, R.

1997-01-01

The integral enthalpy of formation of the Sm-Pb and Sm-Sn melts at 1203 K, h f , was determined by direct reaction calorimetry (drop method) in the Pb and Sn rich sides with the help of a high-temperature Tian-Calvet calorimeter. The results can be fitted respectively with reference to the mole fraction of samarium, x, as follows: f /kJmol -1 =x(1-x)(-109.8 -372.0.7x) with 0 Sm f /kJmol -1 =x(1- x)(-277.0+105.4x) with 0 Sm -1 respectively. Such negative values suggest the existence of a strong short-range order in the liquid state. The stoichiometry and the thermal stability of these associations needs additional thermodynamic determinations concerning mainly the free enthalpy of formation. It will be determined by Knudsen-effusion combined with mass spetrometry in a further work. (orig.)

Dual-labeled time-resolved fluoroimmunoassay for simultaneous detection of clothianidin and diniconazole in agricultural samples.

Science.gov (United States)

Sheng, Enze; Shi, Haiyan; Zhou, Liangliang; Hua, Xiude; Feng, Lu; Yu, Tong; Wang, Minghua

2016-02-01

Europium (Eu(3+)) and samarium (Sm(3+)) were used as fluorescent labels to develop a highly sensitive dual-labeled time-resolved fluoroimmunoassay (TRFIA) for detect clothianidin and diniconazole in food samples. Under the optimized assay conditions, 50% inhibition concentration (IC50) and the limit of detection (LOD, IC10) of clothianidin were 5.08 and 0.021 μg/L, and 13.14 and 0.029 μg/L for diniconazole. The cross-reactivities (CRs) were negligible except dinotefuran (9.4%) and uniconazole (4.28%). The recoveries of clothianidin and diniconazole ranged from 79.3% to 108.7% in food samples. The results of TRFIA for the authentic samples were validated by gas chromatography (GC) analyses, and a satisfactory correlations were obtained. These results indicated that the method was an alternative tool for simultaneous detection of clothianidin and diniconazole in food samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

Polarized spectral properties of Sm3+:LiYF4 crystal

International Nuclear Information System (INIS)

Wang, G.Q.; Lin, Y.F.; Gong, X.H.; Chen, Y.J.; Huang, J.H.; Luo, Z.D.; Huang, Y.D.

2014-01-01

A trivalent samarium-doped LiYF 4 single crystal was grown by the vertical Bridgman technique. Its polarized absorption and fluorescence spectra and fluorescence decay curves were recorded at room temperature. On the basis of the Judd–Ofelt theory, the spectral parameters of the Sm 3+ :LiYF 4 crystal were calculated. The emission cross sections for the 4 G 5/2 → 6 H J (J=5/2, 7/2. 9/2, and 11/2) transitions of special interest for visible laser application were obtained by the Fuchtbauer–Ladenburg formula. -- Highlights: • Polarized spectral properties of Sm 3+ :LiYF 4 crystal at room temperature were analyzed in detail. • The emission cross sections for the transitions of special interest for visible laser application are calculated. • Sm 3+ :LiYF 4 is a promising laser material for 401 nm GaN LD pumped 605 nm visible laser

Investigation of optimal photoionization schemes for Sm by multi-step resonance ionization

International Nuclear Information System (INIS)

Cha, H.; Song, K.; Lee, J.

1997-01-01

Excited states of Sm atoms are investigated by using multi-color resonance enhanced multiphoton ionization spectroscopy. Among the ionization signals one observed at 577.86 nm is regarded as the most efficient excited state if an 1-color 3-photon scheme is applied. Meanwhile an observed level located at 587.42 nm is regarded as the most efficient state if one uses a 2-color scheme. For 2-color scheme a level located at 573.50 nm from this first excited state is one of the best second excited state for the optimal photoionization scheme. Based on this ionization scheme various concentrations of standard solutions for samarium are determined. The minimum amount of sample which can be detected by a 2-color scheme is determined as 200 fg. The detection sensitivity is limited mainly due to the pollution of the graphite atomizer. copyright 1997 American Institute of Physics

Direct measurement of the energy spectrum of an intense proton beam

International Nuclear Information System (INIS)

Leeper, R.J.; Lee, J.R.; Kissel, L.; Johnson, D.J.; Stygar, W.A.; Hebron, D.E.; Roose, L.D.

1983-01-01

A time-resolved magnetic spectrometer has been used to measure the energy spectrum of an intense (0.5 TW/cm 2 ) proton beam. A thin (2400 A) gold foil placed at the focus of an ion diode Rutherford scattered protons by 90 0 into the spectrometer, reducing the beam intensity to a level suitable for magnetic analysis. The scattered beam was collimated by two 1 mm diameter apertures separated by 12.3 cm. The collimated protons were deflected in a 12.7 cm diameter, 6.65 Kg samarium-cobalt permanent magnet. The deflected protons were recorded simultaneously on CR-39 and eight 1 mm 2 by 35 μm thick PIN diodes. A Monte Carlo computer code was used to calculate the sensitivity and resolution of the spectrometer. Data taken on Proto-I show a 150 keV to 250 keV wide proton energy spectrum at each instant in time

Spatial modification of laser beam under the influence of Λ-type strong pump

International Nuclear Information System (INIS)

Lee, Won Kyu; Noh, Young Chul; Jeon, Jin Ho; Lee, Jai Hyung; Chang, Joon Sung

1999-01-01

The laser beam propagating through the resonant medium undergo severe deformation because of nonlinear interaction such as self-focusing, self-defocusing, etc. When strong pump beam coexists with the probe beam, propagation characteristics can be changed. We use samarium (Sm) vapor as the nonlinear medium. Probe laser is tuned around 4f 6 6s 27 F 0 -> 4f 6 ( 7 F)6s6p( 1 P 0 ) transition line of Sm (561.601 nm) and the pump laser is tuned around 4f 6 6s 27 F 1 -> 4f 6 ( 7 F)6s6p( 1 P 0 ) transition line of Sm (572.019 nm). The probe and the pump beams are Λ-type configuration. The transmission of the probe beam is changed as the intensity and the detuning of the pump beam are varied. The degree of self-focusing is also modified. (author)

Level densities and γ-strength functions in 148,149Sm

International Nuclear Information System (INIS)

Siem, S.; Guttormsen, M.; Ingeberg, K.; Melby, E.; Rekstad, J.; Schiller, A.; Voinov, A.

2002-01-01

The level densities and γ-strength functions of the weakly deformed 148 Sm and 149 Sm nuclei have been extracted. The temperature versus excitation energy curve, derived within the framework of the microcanonical ensemble, shows structures, which we associate with the breakup of Cooper pairs. The nuclear heat capacity is deduced within the framework of both the microcanonical and canonical ensembles. We observe negative heat capacity in the microcanonical ensemble whereas the canonical heat capacity exhibits an S shape as a function of temperature, both signals of a phase transition. The structures in the γ-strength functions are discussed in terms of the pygmy resonance and the scissors mode built on excited states. The samarium results are compared with data for the well-deformed 161,162 Dy, 166,167 Er, and 171,172 Yb isotopes and with data from (n,γ) experiments and giant dipole resonance studies

The relevance of rare earth elements to nuclear medicine

International Nuclear Information System (INIS)

Cox, P.H.

1998-01-01

Full text: The lanthanides are an interesting series of metallic elements which have almost identical chemical characteristics and which offer a variety of radioisotopes with differing energy spectra suitable for open source therapy. Their inorganic salts tend to form chemically and biological stable colloids which have proved to be useful for intercavity therapies, in particular for synovectomy. Yttrium-90 silicate is a standard product for large joints with a thick synovium whilst for smaller joints Erbium-169, with its shorter tissue penetration, is more widely used for smaller joints to reduce the risk of radiation induced bone necrosis. Recently the development of an inert biodegradable colloid, chitosan, labelled with Holmium 166. for intercavity therapy of cystic brain tumours has been reported. Yttrium-90 has been chelated to peptide and antibody fragments for tumour targeting as a potentially more effective radionuclide than Iodine-131. The search for alternatives to Strontium-89 for the palliative treatment of pain arising from bone metastases has led to the introduction of diphosphonate complexes of Samarium-153, Lutetium-177 and Holmium-166. These complexes are of special interest because the radionuclides can be produced economically in developing countries. Terbium-149, an alpha emitter, has been mentioned as a possible therapeutic radionuclide. Yttrium-90 and Holmium-166 can an both be made available as generator products which is an added potential advantage for developing nuclear medical applications

HDDR in Sm-Co alloys - a new method for magnetic hardening of Sm-Co permanent magnets

Energy Technology Data Exchange (ETDEWEB)

Kubis, M.; Handstein, A.; Gebel, B.; Mueller, K.-H.; Schultz, L. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe; Gutfleisch, O. [Institut fuer Festkoerper- und Werkstofforschung Dresden e.V. (Germany). Inst. fuer Metallische Werkstoffe]|[Birmingham Univ. (United Kingdom). School of Metallurgy and Materials

1998-07-01

Investigations on the hydrogen absorption behavior of different Sm-Co alloys with 1:5 and 2:17 structure by differential scanning calorimetry (DSC) at enhanced hydrogen pressures between 1 MPa and 7 MPa indicated different hydrogen absorption events. X-ray diffraction (XRD) studies and microstructural investigations showed clearly the disproportionation of the Sm-Co phases into Sm hydride and Co or Co-rich phases for hydrogen pressures above 0.5 MPa. The favourable effect of high hydrogen pressures can be explained in terms of a decrease of the free enthalpy of the samarium hydride for increasing hydrogen pressures. Additionally, Sm-Co alloys of both types were reactively milled under hydrogen at enhanced temperatures. The reactively milled powders showed again the products of the disproportionation reaction. A recombination of Sm-Co phases by removing the hydrogen in a second heat treatment was successful for both methods. Investigations of the magnetic properties showed coercivities {mu}{sub OJ}H{sub C} of up to 2.1 T for high pressure HDDR powders of SmCo{sub 5} material, demonstrating clearly the positive effect of the hydrogen treatment on the coercivity. The reactively milled powders showed for recombination temperatures {<=}700 C a remanence enhancement which could be attributed to the exchange coupling of the nanoscaled grains. A maximum coercivity {mu}{sub OJ}H{sub C} of 3.7 T was achieved for SmCo{sub 5} and a maximum energy product (BH){sub max} of 82 kJ/m{sup 3} was measured for an Sm-rich Sm{sub 2}Co{sub 17} sample. (orig.)

HDDR in Sm-Co alloys - a new method for magnetic hardening of Sm-Co permanent magnets

International Nuclear Information System (INIS)

Kubis, M.; Handstein, A.; Gebel, B.; Mueller, K.-H.; Schultz, L.; Gutfleisch, O.; Birmingham Univ.

1998-01-01

Investigations on the hydrogen absorption behavior of different Sm-Co alloys with 1:5 and 2:17 structure by differential scanning calorimetry (DSC) at enhanced hydrogen pressures between 1 MPa and 7 MPa indicated different hydrogen absorption events. X-ray diffraction (XRD) studies and microstructural investigations showed clearly the disproportionation of the Sm-Co phases into Sm hydride and Co or Co-rich phases for hydrogen pressures above 0.5 MPa. The favourable effect of high hydrogen pressures can be explained in terms of a decrease of the free enthalpy of the samarium hydride for increasing hydrogen pressures. Additionally, Sm-Co alloys of both types were reactively milled under hydrogen at enhanced temperatures. The reactively milled powders showed again the products of the disproportionation reaction. A recombination of Sm-Co phases by removing the hydrogen in a second heat treatment was successful for both methods. Investigations of the magnetic properties showed coercivities μ OJ H C of up to 2.1 T for high pressure HDDR powders of SmCo 5 material, demonstrating clearly the positive effect of the hydrogen treatment on the coercivity. The reactively milled powders showed for recombination temperatures ≤700 C a remanence enhancement which could be attributed to the exchange coupling of the nanoscaled grains. A maximum coercivity μ OJ H C of 3.7 T was achieved for SmCo 5 and a maximum energy product (BH) max of 82 kJ/m 3 was measured for an Sm-rich Sm 2 Co 17 sample. (orig.)

Sorption of activation products on London clay and Dungeness aquifer gravel

International Nuclear Information System (INIS)

Baston, G.M.N.; Berry, J.A.; Littleboy, A.K.; Pilkington, N.J.

1992-01-01

The sortpion of a series of activation-product radionuclides onto London clay and Dungeness aquifer gravel from the nuclear reactor sites at Bradwell and Dungeness, has been examined. Batch sorption and through-diffusion experiments with clay determined chlorine as the chloride ion to be effectively non-sorbing; calcium to be weakly sorbing, whereas cobalt, nickel, niobium and samarium were moderately to strongly sorbing and silver was strongly sorbing. Distribution ratios (R D values) for Nb, Sm and Ag were found to have a strong dependence on the liquid-solid separation technique employed. The presence of high concentrations of calcium hydroxide led to lower values of R D for radioactive Ca but higher R D values for Sm and Ag. The sorption of Ni showed no apparent dependence on groundwater composition at low levels of dissolved organic carbon (DOC). The values of R D for Co decreased as the DOC content was increased by addition of humic materials. Batch sorption studies with aquifer gravel demonstrated that Ca is weakly sorbing whereas Nb, Ag and Eu are moderately to strongly sorbing. R D values for Ca and for Ag under neutral pH conditions show little sensitivity to the liquid/solid separation technique used. However, R D values for Nb and Eu under neutral pH conditions and for Ag in alkaline solution (pH = 11 - 12) show a marked effect. The aquifer gravel was found to be highly inhomogeneous unlike the clay and sorption was greatest on samples with a high proportion of sand, reflecting the clay mineral content. (orig.)

Development of a methodology for the separation of europium and samarium from a mixture of rare earth oxides by electroreduction/ precipitation

International Nuclear Information System (INIS)

Chepcanoff, Vera

2006-01-01

The rare earths (RE) were first used in 1903, when Welsbach developed a lighter that is still used today. Nowadays, the RE are employed in many different fields, as in the production of super-alloys , as catalysts for petroleum industry, in the manufacture of non-ferrous alloys, color television tubes, x-ray screens, special glasses, ceramics, computer industries, nuclear medicine, lasers, pigments, etc., moving, in the last decade , a market of US$ 2 billions per year. Due to their similar properties, the RE elements are very difficult to separate, requiring complex processes, what make the products very expensive. Elements like Eu and Sm, which contents in the minerals are low (0.05% and 2.0%, respectively, in monazite) are extremely expensive, but their field of application justifies the research for looking for other processes, more simple and/or more effective. Trivalent state is a characteristic of all RE, but some of them presents oxidation state +2, like Ce, Eu, Sm and Yb. In the case of Eu and Sm, the focus of the present work, the divalent state is achieved by electro-reduction in the potentials -0.65 and -1.55 (SCE), respectively. This makes possible the separation of these elements from the other rare earths and from each other. Thus, making use of this characteristic, a process for the individual separation of Eu and Sm in (NH 4 ) 2 SO 4 solution by electro-reduction/precipitation is proposed, where Sm is first separated from the solution as sulfate, and Eu, that remains in the solution, is precipitated after the decrease of temperature and potential applied. The process developed from a synthetic Eu and Sm solution was applied to a mixture of semi-heavy RE oxide, produced at IPEN-CNEN/SP, obtaining the separation of Sm. This product was analyzed by spectrophotometry, showing high purity. (author)

Up-grading a 4.7-cm-period plane electromagnetic undulator

CERN Document Server

Bogachenkov, V A; Papadichev, V A

1999-01-01

Electromagnetic undulators have a number of advantages over permanent-magnet undulators. They are less expensive to fabricate and their field is easily regulated by changing the current, without requiring a complex and expensive precision system for changing the undulator gap. Their main weaknesses are that they require a large power supply and that the field is limited due to yoke saturation mainly because of large axial stray fluxes, particularly in simple constructions. Modernization of a 4.7-cm-period, 20-period long plane electromagnetic undulator of simple design is described. Samarium-cobalt permanent magnets were used to increase the field and decrease power consumption. They were placed between adjacent rings (with opposite sign of field) and while increasing the working field they decreased saturation of the iron yokes. Small lateral displacements of permanent magnets were used to equalize field amplitudes in half periods of the undulator with 0.1% accuracy. Matched input and output to and from the ...

Double Solvent for Extracting Rare Earth Concentrate

International Nuclear Information System (INIS)

Bintarti, AN; Bambang EHB

2007-01-01

An extraction process to rare earth concentrate which contain elements were yttrium (Y), lanthanum (La), cerium (Ce), neodymium (Nd), samarium (Sm), gadolinium (Gd) and dysprosium (Dy) which were dissolved in to nitric acid has been done. The experiment of the extraction by double solvent in batch to mix 10 ml of the feed with 10 ml solvent contained the pair of solvent was TBP and TOA, D2EHPA and TOA, TBP and D2EHPA in cyclohexane as tinner. It was selected a right pairs of solvent for doing variation such as the acidity of the feed from 2 - 6 M and the time of stirring from 5 - 25 minutes gave the good relatively extraction condition to Dy element such as using 10 % volume of TOA in D2EHPA and cyclohexane, the acidity of the feed 3 M and the time stirring 15 minutes produced coefficient distribution to dysprosium = 0.586 and separation factor Dy-Ce = ∼ (unlimited); Dy-Nd = 4.651. (author)

Preparation of Sm2Fe17-xGaxNy/Cy magnets by a hydrogenation-disproportionation-desorption-recombination process

International Nuclear Information System (INIS)

Kubis, M.; Cao, L.; Handstein, A.; Gebel, B.; Mueller, K.; Schultz, L.

1997-01-01

A hydrogenation-disproportionation-desorption-recombination process (HDDR) was applied to Sm 2 Fe 17-x Ga x (x=0.5, 1, and 2). The process was studied by means of temperature-pressure analysis, x-ray diffraction and scanning electron microscopy. It was shown that Ga not only stabilizes the interstitially modified compounds Sm 2 Fe 17-x Ga x C y (0 2 Fe 17-x Ga x against the disproportionation by hydrogen. Therefore, only for x=0.5 can a nearly complete HDDR be performed. The HDDR-treated and subsequently nitrogenated or carburized samples show coercivities μ 0J H C up to 3.1 T and 2.5 T, respectively. Hot compaction increases the density of the Sm 2 Fe 16.5 Ga 0.5 C y powder; however, it leads to a loss of coercivity due to decomposition into α-iron and samarium carbides. copyright 1997 American Institute of Physics

Uranium hydrogeochemical and stream sediment reconnaissance of the Bozeman NTMS quadrangle, Montana, including concentrations of forty-two additional elements

International Nuclear Information System (INIS)

Bolivar, S.L.; Hensley, W.K.; Van Haaften, I.J.; Pirtle, J.; George, W.E.; Gallimore, D.; Apel, C.; Hansel, J.

1980-07-01

This report contains uranium analyses for 1251 water samples and multielement analyses for 1536 sediment samples. Sediments were analyzed for uranium and thorium as well as aluminum, antimony, barium, beryllium, bismuth, cadmium, calcium, cerium, cesium, chlorine, chromium, cobalt, copper, dysprosium, europium, gold, hafnium, iron, lanthanum, lead, lithium, lutetium, magnesium, manganese, nickel, niobium, potassium, rubidium, samarium, scandium, silver, sodium, strontium, tantalum, terbium, tin, titanium, tungsten, vanadium, ytterbium, and zinc. Water samples were initially analyzed for uranium by fluorometry. All water samples containing more than 40 ppB uranium were reanalyzed by delayed-neutron counting (DNC). All sediments were analyzed for uranium by DNC. Other elemental concentrations in sediments were determined by neutron activation analysis for 31 elements, by x-ray fluorescence for 9 elements, and by arc-source emission spectrography for 2 elements. Analytical results for sediments are reported as parts per million. Descriptions of procedures used for analysis of water and sediment samples as well as analytical precisions and detection limits are given

Sulphate-ceria composite ceramics for energy environmental co-generation technology

International Nuclear Information System (INIS)

Liu, X.R.; Zhu, B.; Xu, J.; Sun, J.C.; Mao, Z.Q.

2005-01-01

In this work ion conductivity and FC application were studied for the new type composite material based on SDC (samarium doped ceria) and Li 2 SO 4 . Significant conductivity enhancement was achieved, e.g. 10 -2 -0.4 Scm -1 for the SDC-Li 2 SO 4 compared to 10 -4 -10 -2 Scm -1 for the SDC between 400 and 650 C. Some ion conductivity mechanisms were proposed correspondingly. Using the SDC-Li 2 SO 4 composite materials as the electrolytes, we achieved high performances, 200-540 mWcm -2 , for intermediate temperature (450-650 C) solid oxide FC (ITSOFC) applications. Sulfates, typically Li 2 SO 4 , have an excellent chemical stability in sulfur containing atmosphere. The sulfate-ceria (SDC-Li 2 SO 4 ) composite materials can thus meet the demands to develop the sulfur tolerant and H 2 S FC technologies, which was also demonstrated successfully with significant importance for both fundamental and applied research. (orig.)

Study of non-metallic inclusion sources in steel

International Nuclear Information System (INIS)

Khons, Ya.; Mrazek, L.

1976-01-01

A study of potential inclusion sources was carried out at the Tvinec steel plant using an unified labelling procedure for different sources. A lanthanum oxide labelling method has been used for refractories with the subsequent La determination in steel by the neutron activation analysis. Samarium and cerium oxides and the 141 Ce radionuclide have been used in conjunction with the testing. The following sources of exogenous inclusions have been studied: 1)Refractory material comprising fireclay and corundum for steel-teeming trough in open-heart furnaces; 2) Fireclay bottom-pouring refractories; 3) Steel-teeming laddle lining; 4) Heat-insulating and exothermic compounds for steel ingots; 5) Vacuum treatment plant lining; 6) Open-hearth and electric arc furnace slag. The major oxide inclusion source in steel was found to be represented by the furnace slag, since it forms about 40 p.c. of all oxide inclusions. The contributions of the remaining sources did not exceede 5 p.c. each

Chemical and valence reconstruction at the surface of SmB6 revealed by means of resonant soft x-ray reflectometry

Science.gov (United States)

Zabolotnyy, V. B.; Fürsich, K.; Green, R. J.; Lutz, P.; Treiber, K.; Min, Chul-Hee; Dukhnenko, A. V.; Shitsevalova, N. Y.; Filipov, V. B.; Kang, B. Y.; Cho, B. K.; Sutarto, R.; He, Feizhou; Reinert, F.; Inosov, D. S.; Hinkov, V.

2018-05-01

Samarium hexaboride (SmB6), a Kondo insulator with mixed valence, has recently attracted much attention as a possible host for correlated topological surface states. Here, we use a combination of x-ray absorption and reflectometry techniques, backed up with a theoretical model for the resonant M4 ,5 absorption edge of Sm and photoemission data, to establish laterally averaged chemical and valence depth profiles at the surface of SmB6. We show that upon cleaving, the highly polar (001) surface of SmB6 undergoes substantial chemical and valence reconstruction, resulting in boron termination and a Sm3 + dominated subsurface region. Whereas at room temperature, the reconstruction occurs on a timescale of less than 2 h, it takes about 24 h below 50 K. The boron termination is eventually established, irrespective of the initial termination. Our findings reconcile earlier depth resolved photoemission and scanning tunneling spectroscopy studies performed at different temperatures and are important for better control of surface states in this system.

Structure and properties of electron-doped Ca1-xSmxMnO3 nanoparticles

International Nuclear Information System (INIS)

Sanmathi, C.S.; Retoux, R.; Singh, M.P.; Noudem, J.

2009-01-01

In this paper, we report the structural and magnetic properties of electron-doped Ca 1-x Sm x MnO 3 (CSM) nanoparticles. The samarium's composition 'x' was varied from 0 to 0.2 with the special attention up to 0.05. Spherical 60-70 nm polycrystalline CSM nanoparticles were synthesised by chemical co-precipitation technique. Doping of Sm 3+ in antiferromagnetic CaMnO 3 has drastically altered its magnetic behavior due to the formation of ferromagnetic clusters. For example, the CSM powder with x = 0.04 displays about 115 K magnetic Curie temperature and about 0.1 emu/mole saturation magnetization. Physical properties of our nano-CSM powders are also compared with identical bulk-samples. To understand the differences, we invoked the intra-grain and inter-grain magnetic coupling process that facilitates to enhance their ferromagnetic behaviors. Unlike the bulk samples, such magnetic couplings in nanoparticles are favored by the presence of low-level crystal and interfacial defects

Pyrometallurgical separation processes of radionuclides contained in the irradiated nuclear fuel

International Nuclear Information System (INIS)

De Cordoba, Guadalupe; Caravaca, Concha; Quinones, Javier; Gonzalez de la Huebra, Angel

2005-01-01

Faced with the new options for the high level waste management, the ''Partitioning and Transmutation (P and T)'' of the radio nuclides contained in the irradiated nuclear fuel appear as a promising option from different points of view, such as environmental risk, radiotoxic inventory reduction, economic, etc.. The present work is part of a research project called ''PYROREP'' of the 5th FWP of the EU that studied the feasibility of the actinide separation from the rest of fission products contained in the irradiated nuclear fuel by pyrometallurgical processes with the aim of their transmutation. In order to design these processes it is necessary to determine basic thermodynamic and kinetic data of the radionuclides contained in the nuclear fuel in molten salt media. The electrochemical study of uranium, samarium and molybdenum in the eutectic melt LiCl - KCl has been performed at a tungsten electrode in the temperature range of 450 - 600 deg C in order to obtain these basic properties. (Author)

Measurement of the Slowing-Down and Thermalization Time of Neutrons in Water

Energy Technology Data Exchange (ETDEWEB)

Moeller, E [AB Atomenergi, Nykoeping (Sweden); Sjoestrand, N G [Chalmers Univ. of Technology, Goeteborg (Sweden)

1963-11-15

The experimental equipment for the study of the time behaviour of neutrons during slowing-down and thermalization in a moderator by the use of a pulsed van de Graaff accelerator as a neutron source is described. Information on the change with time of the neutron spectrum is obtained from its reaction with spectrum indicators, the reaction rate being observed by the detection of capture gamma rays. The time resolution may be chosen in the range 0.01 to 5 {mu}s. Measurements have been made for water with cadmium, gadolinium and samarium as indicators dissolved in the medium. A slowing- down time to 0.2 eV of 2.7 {+-} 0.4 {mu}s and a total thermalization time of 25 - 30 {mu}s were obtained. From 9 {mu}s after the injection, the results are well described by the assumption of the flux as a Maxwell distribution cooling down to the moderator temperature with a thermalization time constant of 4.1 {+-} 0.4 {mu}s.

Study of SmS properties in the low pressure phase (black phase)

International Nuclear Information System (INIS)

Bordier, G.

1986-01-01

SmS was studied for the transition from low pressure phase (black phase) to high pressure phase with an intermediate valence. But the study of the black phase is very rich. The variations of electron transport properties with pressure at low temperature show a semi-metal phase located, in the pressure-temperature diagram in the black phase for pressure over 4 kbars, corresponding to the phase B'of the doping-temperature diagram. Electron spin resonance shows a lack of sulfur and nearby this defect a samarium ion, magnetically coupled with the matrix, presents a divalent trivalent transition. Resonance lines are broadened with temperature. Conductivity relaxations occur at low pressure and low temperature by trapping a conduction electron, by magnetic exchange giving a bounded magnetic polaron. The relaxation time at null magnetic field is activated. An approximation of trapping barrier and critical field corresponding the maximum magnetoresistance is given by a model [fr

Theoretical study of the structure and the reactivity of lanthanides and actinides complexes: Activation of small molecules

International Nuclear Information System (INIS)

Castro, Ludovic

2012-01-01

This PhD thesis presents a theoretical study of the structure and the reactivity of organometallic complexes of lanthanides and actinides at the DFT level. After a general introduction of the methods of theoretical chemistry used for the modelling of organometallic reactivity, a study of the participation of 5f electrons in uranium(IV) reactivity is presented. The results show that the large core ECP can be used safely in order to treat the actinide and so that 5f electrons can be treated implicitly. Then, the reactivity of uranium(III) complexes with CO 2 and other analogous molecules is studied via multiple examples from the literature. These studies show that the steric nature of the ligands is very important and controls the reactivity. This study is then extended to samarium(II) complex. Eventually, the reactivity of a hydride complex of cerium(III) with MeOSO 2 Me is investigated and theoretical results are compared with experimental observations. (author) [fr

A novel orange-red emitting NaCaVO{sub 4}:Sm{sup 3+} phosphor for solid state lighting

Energy Technology Data Exchange (ETDEWEB)

Biswas, Pankaj, E-mail: pankaj79biswas@gmail.com; Kumar, Vinay, E-mail: vinaykdhiman@yahoo.com [School of Physics, Shri Mata Vaishno Devi University, Katra-182320 J& K (India); Ntwaeaborwa, O. M.; Swart, H. C. [Department of Physics, University of the Free State, P.O. Box 339, Bloemfontein, ZA9300 (South Africa)

2016-05-06

The samarium doped NaCaVO{sub 4} phosphor was synthesized by the combustion method. The X-ray powder diffraction (XRD) analysis confirmed that the phosphor powder crystallized as orthorhombic structure belonging to space group Cmcm. From Williamson-Hall analysis the grain size and microstrain in the powder was estimated. The Fourier- transform infrared (FT-IR) studies further validated the formation of vanadate phase of the phosphor. Photoluminescence (PL) study revealed that the phosphor could be efficiently excited by UV-VIS from 200 nm to 500 nm. The 565 nm, 602 nm, 648 nm and 713 nm emissions were ascribed to {sup 4}G{sub 5/2} to {sup 6}H{sub J} (J = 5/2, 7/2, 9/2 and 11/2) transitions of the Sm{sup 3+} ion. The present material may be explored as a novel phosphor to be excited by UV light emitting diodes (LEDs) chips for solid-state lighting and display applications.

Lanthanide Phytanates: Liquid-Crystalline Phase Behavior, Colloidal Particle Dispersions, and Potential as Medical Imaging Agents

Energy Technology Data Exchange (ETDEWEB)

Conn, Charlotte E.; Panchagnula, Venkateswarlu; Weerawardena, Asoka; Waddington, Lynne J.; Kennedy, Danielle F.; Drummond, Calum J. (CSIRO/MHT); (CSIRO/MSE)

2010-08-23

Lanthanide salts of phytanic acid, an isoprenoid-type amphiphile, have been synthesized and characterized. Elemental analysis and FTIR spectroscopy were used to confirm the formed product and showed that three phytanate anions are complexed with one lanthanide cation. The physicochemical properties of the lanthanide phytanates were investigated using DSC, XRD, SAXS, and cross-polarized optical microscopy. Several of the hydrated salts form a liquid-crystalline hexagonal columnar mesophase at room temperature, and samarium(III) phytanate forms this phase even in the absence of water. Select lanthanide phytanates were dispersed in water, and cryo-TEM images indicate that some structure has been retained in the dispersed phase. NMR relaxivity measurements were conducted on these systems. It has been shown that a particulate dispersion of gadolinium(III) phytanate displays proton relaxivity values comparable to those of a commercial contrast agent for magnetic resonance imaging and a colloidal dispersion of europium(III) phytanate exhibits the characteristics of a fluorescence imaging agent.

Pressure-induced phase transformation in zircon-type orthovanadate SmVO4 from experiment and theory

International Nuclear Information System (INIS)

Popescu, C; Garg, Alka B; Errandonea, D; Sans, J A; Rodriguez-Hernández, P; Radescu, S; Muñoz, A; Achary, S N; Tyagi, A K

2016-01-01

The compression behavior of zircon-type samarium orthovanadate, SmVO 4 , has been investigated using synchrotron-based powder x-ray diffraction and ab initio calculations of up to 21 GPa. The results indicate the instability of ambient zircon phase at around 6 GPa, which transforms to a high-density scheelite-type phase. The high-pressure phase remains stable up to 21 GPa, the highest pressure reached in the present investigations. On pressure release, the scheelite phase is recovered. The crystal structure of the high-pressure phase and the equations of state for the zircon- and scheelite-type phases have been determined. Various compressibilities, such as the bulk, axial and bond compressibilities, estimated from the experimental data are found to be in good agreement with the results obtained from theoretical calculations. The calculated elastic constants show that the zircon structure becomes mechanically unstable beyond the transition pressure. Overall there is good agreement between the experimental and theoretical findings. (paper)

High pressure measurement of the uniaxial stress of host layers on intercalants and staging transformation of intercalation compounds

CERN Document Server

Park, T R; Kim, H; Min, P

2002-01-01

A layered double-hydroxide intercalation compound was synthesized to measure the uniaxial stress the host layers exert on the intercalants. To measure the uniaxial stress, we employed the photoluminescence (PL) from the intercalated species, the Sm ion complex, as it is sensitive to the deformation of the intercalants. Of the many PL peaks the Sm ion complex produces, the one that is independent of the counter-cation environment was chosen for the measurement since the Sm ion complexes are placed under a different electrostatic environment after intercalation. The peak position of the PL was redshifted linearly with increasing hydrostatic pressure on the intercalated sample. Using this pressure-induced redshifting rate and the PL difference at ambient pressure between the pre-intercalation and the intercalated ions, we found that, in the absence of external pressure, the uniaxial stress exerted on the samarium ion complexes by the host layers was about 13.9 GPa at room temperature. Time-resolved PL data also ...

Preparation of SDC electrolyte thin films on dense and porous substrates by modified sol-gel route

International Nuclear Information System (INIS)

Lin Hongfei; Ding, Changsheng; Sato, Kazuhisa; Tsutai, Yoshifumi; Ohtaki, Hiromichi; Iguchi, Mabito; Wada, Chiharu; Hashida, Toshiyuki

2008-01-01

Nanocrystalline fluorite type samarium doped ceria (SDC) electrolyte thin film for intermediate temperature-solid oxide fuel cells (IT-SOFCs) application were prepared on the dense and porous substrates at low temperatures of 573-1373 K using a novel citrate sol-gel route combined with a sol suspension spray coating technique. Thermogravimetric analysis showed that the decomposition of the citrate gel film and the initial crystallization of the SDC occurred at a low temperature of about 590 K. XRD examination revealed that the annealing of the green film at temperatures of 573-1373 K provided cubic nanocrystalline SDC phase. The crystallite sizes were in the range of 9-19 nm. Microscopic observations indicated that the derived film was homogeneous, dense and crack-free without pinholes. The desired thickness for preparation of thin electrolyte films from hundreds of nm to several μm should be controllable and feasible by repeating the simple and inexpensive citrate sol-gel spray coating process

Lanthanide Phytanates: Liquid-Crystalline Phase Behavior, Colloidal Particle Dispersions, and Potential as Medical Imaging Agents

International Nuclear Information System (INIS)

Conn, Charlotte E.; Panchagnula, Venkateswarlu; Weerawardena, Asoka; Waddington, Lynne J.; Kennedy, Danielle F.; Drummond, Calum J.

2010-01-01

Lanthanide salts of phytanic acid, an isoprenoid-type amphiphile, have been synthesized and characterized. Elemental analysis and FTIR spectroscopy were used to confirm the formed product and showed that three phytanate anions are complexed with one lanthanide cation. The physicochemical properties of the lanthanide phytanates were investigated using DSC, XRD, SAXS, and cross-polarized optical microscopy. Several of the hydrated salts form a liquid-crystalline hexagonal columnar mesophase at room temperature, and samarium(III) phytanate forms this phase even in the absence of water. Select lanthanide phytanates were dispersed in water, and cryo-TEM images indicate that some structure has been retained in the dispersed phase. NMR relaxivity measurements were conducted on these systems. It has been shown that a particulate dispersion of gadolinium(III) phytanate displays proton relaxivity values comparable to those of a commercial contrast agent for magnetic resonance imaging and a colloidal dispersion of europium(III) phytanate exhibits the characteristics of a fluorescence imaging agent.

Crystal structure of a samarium(III nitrate chain cross-linked by a bis-carbamoylmethylphosphine oxide ligand

Directory of Open Access Journals (Sweden)

Julie A. Stoscup

2014-10-01

Full Text Available In the title compound poly[aquabis(μ-nitrato-κ4O,O′:O,O′′tetrakis(nitrato-κ2O,O′{μ4-tetraethyl [(ethane-1,2-diylbis(azanediylbis(2-oxoethane-2,1-diyl]diphosphonate-κ2O,O′}disamarium(III], [Sm2(NO36(C14H30N2O8P2(H2O]n, a 12-coordinate SmIII and a nine-coordinate SmIII cation are alternately linked via shared bis-bidentate nitrate anions into a corrugated chain extending parallel to the a axis. The nine-coordinate SmIII atom of this chain is also chelated by a bidentate, yet flexible, carbamoylmethylphoshine oxide (CMPO ligand and bears one water molecule. This water molecule is hydrogen bonded to nitrate groups bonded to the 12-coordinate SmIII cation. The CMPO ligand, which lies about an inversion center, links neighboring chains along the c axis, forming sheets parallel to the ac plane. Hydrogen bonds between the amide NH group and metal-bound nitrate anions are also present in these sheets. The sheets are packed along the b axis through only van der Waals interactions.

The lattice dynamical studies of rare earth compounds: electron-phonon interactions

International Nuclear Information System (INIS)

Jha, Prafulla K.; Sanyal, Sankar P.; Singh, R.K.

2002-01-01

During the last two decades chalcogenides and pnictides of rare earth (RE) atoms have drawn considerable attention of the solid state physicists because of their peculiar electronic, magnetic, optical and phonon properties. Some of these compounds e.g. sulphides and selenides of cerium (Ce), samarium (Sm), yttrium (Y), ytterbium (Yb), europium (Eu) and thulium (Tm) and their alloys show nonintegral valence (between 2 and 3), arising due to f-d electron hybridization at ambient temperature and pressure. The rare earth mixed valence compounds (MVC) reviewed in this article crystallize in simple cubic structure. Most of these compounds show the existence of strong electron-phonon coupling at half way to the zone boundary. This fact manifests itself through softening of the longitudinal acoustic mode, negative value of elastic constant C 12 etc. The purpose of this contribution is to review some of the recent activities in the fields of lattice dynamics and allied properties of rare earth compounds. The present article is primarily devoted to review the effect of electron-phonon interactions on the dynamical properties of rare earth compounds by using the lattice dynamical model theories based on charged density deformations and long-range many body forces. While the long range charge transfer effect arises due to f-d hybridization of nearly degenerate 4f-5d bands of rare earth ions, the density deformation comes into the picture of breathing motion of electron shells. These effects of charge transfer and charge density deformation when considered in the lattice dynamical models namely the three body force rigid ion model (TRM) and breathing shell model (BSM) are quite successful in explaining the phonon anomalies in these compounds and undoubtedly unraveled many important physical process governing the phonon anomalies in rare earth compounds

Quantitative analysis of thorium in the presence of rare earth by X-ray fluorescence spectrometry

International Nuclear Information System (INIS)

Jesus, Camila S. de; Taam, Isabel; Vianna, Claudio A.

2013-01-01

The occurrence of Thorium in ores is normally associated to other elements such as Uranium and Cerium, as well as some Rare-Earths (RE). The separation of these elements by traditional analytic chemistry techniques is both time and reagent consuming, thus increasing the analysis cost. The hereby proposed method consists in the direct determination of Thorium in rare earths ores and compounds by X-ray fluorescence spectroscopy without any prior chemical separation from other matrix elements. This non-destructive technique is used to determine which elements are present in solid and liquid samples, as well as their concentrations. The studied matrix contains Lanthanum, Cerium, Praseodymium, Neodymium, Samarium, Gadolinium and Yttrium. This study evaluated the analytical lines of radiation emission for each rare earth contained in the matrix, comparing it to the Thorium main analytical line. The Thorium quantification was measured through the Th L line, where there is no influence or interference from the rare earths analytical lines. The studied samples are certified standards and the obtained results have been compared to Ethylenediaminetetraacetic acid (EDTA) titration results, an already well-established and widely trusted method. We also measured the matrix effect thus using complex rare earths liquor. This liquor contains also elements commonly found in monazites sands: phosphates, aluminum, iron. Obtained results state the efficiency of X-ray Fluorescence to determine Thorium in the presence of rare earths without any prior chemical separation. (author)