GLASS COMPOSITION-TCLP RESPONSE MODEL FOR WASTE GLASSES

International Nuclear Information System (INIS)

Kim, Dong-Sang; Vienna, John D.

2004-01-01

A first-order property model for normalized Toxicity Characteristic Leaching Procedure (TCLP) release as a function of glass composition was developed using data collected from various studies. The normalized boron release is used to estimate the release of toxic elements based on the observation that the boron release represents the conservative release for those constituents of interest. The current TCLP model has two targeted application areas: (1) delisting of waste-glass product as radioactive (not mixed) waste and (2) designating the glass wastes generated from waste-glass research activities as hazardous or non-hazardous. This paper describes the data collection and model development for TCLP releases and discusses the issues related to the application of the model

MEASUREMENT OF SPECIFIC HEAT CAPACITY OF SALTSTONE

International Nuclear Information System (INIS)

Harbour, J.; Williams, V.

2008-01-01

One of the goals of the Saltstone variability study is to identify (and quantify the impact of) the operational and compositional variables that control or influence the important processing and performance properties of Saltstone grout mixtures. The heat capacity of the Saltstone waste form is one of the important properties of Saltstone mixes that was last measured at SRNL in 1997. It is therefore important to develop a core competency for rapid and accurate analysis of the specific heat capacity of the Saltstone mixes in order to quantify the impact of compositional and operational variations on this property as part of the variability study. The heat capacity, coupled with the heat of hydration data obtained from isothermal calorimetry for a given Saltstone mix, can be used to predict the maximum temperature increase in the cells within the vaults of the Saltstone Disposal Facility (SDF). The temperature increase controls the processing rate and the pour schedule. The maximum temperature is also important to the performance properties of the Saltstone. For example, in mass pours of concrete or grout of which Saltstone is an example, the maximum temperature increase and the maximum temperature difference (between the surface and the hottest location) are controlled to ensure durability of the product and prevent or limit the cracking caused by the thermal gradients produced during curing. This report details the development and implementation of a method for the measurement of the heat capacities of Saltstone mixes as well as the heat capacities of the cementitious materials of the premix and the simulated salt solutions used to batch the mixes. The developed method utilizes the TAM Air isothermal calorimeter and takes advantage of the sophisticated heat flow measurement capabilities of the instrument. Standards and reference materials were identified and used to validate the procedure and ensure accuracy of testing. Heat capacities of Saltstone mixes were �

MEASUREMENT OF SPECIFIC HEAT CAPACITY OF SALTSTONE

Energy Technology Data Exchange (ETDEWEB)

Harbour, J; Vickie Williams, V

2008-09-29

One of the goals of the Saltstone variability study is to identify (and quantify the impact of) the operational and compositional variables that control or influence the important processing and performance properties of Saltstone grout mixtures. The heat capacity of the Saltstone waste form is one of the important properties of Saltstone mixes that was last measured at SRNL in 1997. It is therefore important to develop a core competency for rapid and accurate analysis of the specific heat capacity of the Saltstone mixes in order to quantify the impact of compositional and operational variations on this property as part of the variability study. The heat capacity, coupled with the heat of hydration data obtained from isothermal calorimetry for a given Saltstone mix, can be used to predict the maximum temperature increase in the cells within the vaults of the Saltstone Disposal Facility (SDF). The temperature increase controls the processing rate and the pour schedule. The maximum temperature is also important to the performance properties of the Saltstone. For example, in mass pours of concrete or grout of which Saltstone is an example, the maximum temperature increase and the maximum temperature difference (between the surface and the hottest location) are controlled to ensure durability of the product and prevent or limit the cracking caused by the thermal gradients produced during curing. This report details the development and implementation of a method for the measurement of the heat capacities of Saltstone mixes as well as the heat capacities of the cementitious materials of the premix and the simulated salt solutions used to batch the mixes. The developed method utilizes the TAM Air isothermal calorimeter and takes advantage of the sophisticated heat flow measurement capabilities of the instrument. Standards and reference materials were identified and used to validate the procedure and ensure accuracy of testing. Heat capacities of Saltstone mixes were

Benzene Evolution Rates from Saltstone Prepared with 2X ITP Flowsheet Concentrations of Phenylborates and Heated to 85 Degrees C

International Nuclear Information System (INIS)

Poirier, M.R.

2000-01-01

The Saltstone Facility provides the final treatment and disposal of low level liquid wastes streams. At the Saltstone Facility, the waste is mixed with cement, flyash, and slag to form a grout, which is pumped into large concrete vaults where it cures. The facility started radioactive operations in June 1990. High Level Waste Engineering requested Savannah River Technology Center to determine the effect of TPB and its decomposition products (i.e., 3PB, 2PB, and 1PB) on the saltstone process. Previous testing performed by SRTC determined saltstone benzene evolution rates a function of ITP filtrate composition. Testing by the Thermal Fluids Laboratory has shown at design operation, the temperature in the Z-area vaults could reach 85 degrees Celsius. Saltstone asked SRTC to perform additional testing to determine whether curing at 85 degrees Celsius could change saltstone benzene evolution rates. This document describes the test performed to determine the effect of curing temperature on the benzene evolution rates

MEASUREMENT OF WASTE LOADING IN SALTSTONE

International Nuclear Information System (INIS)

Harbour, J; Vickie Williams, V

2008-01-01

One of the goals of the Saltstone variability study is to identify the operational and compositional variables that control or influence the important processing and performance properties of Saltstone grout mixtures. One of those properties of importance is the Waste Loading (WL) of the decontaminated salt solution (DSS) in the Saltstone waste form. Waste loading is a measure of the amount of waste that can be incorporated within a waste form. The value of the Saltstone waste loading ultimately determines the number of vaults that will be required to disposition all of the DSS. In this report, the waste loading is defined as the volume in milliliters of DSS per liter of Saltstone waste form. The two most important parameters that determine waste loading for Saltstone are water to cementitious material (w/cm) ratio and the cured grout density. Data are provided that show the dependence of waste loading on the w/cm ratio for a fixed DSS composition using the current premix material (45% Blast Furnace Slag (BFS), 45% Fly Ash (FA) and 10% Ordinary Portland Cement (OPC)). The impact of cured grout density on waste loading was also demonstrated. Mixes (at 0.60 w/cm) made with a Modular Caustic side extraction Unit (MCU) simulant and either OPC or BFS have higher cured grout densities than mixes made with premix and increase the WL to 709 mL/L for the OPC mix and 689 mL/L for the BFS mix versus the value of 653 mL/L for MCU in premix at 0.60 w/cm ratio. Bleed liquid reduces the waste loading and lowers the effective w/cm ratio of Saltstone. A method is presented (and will be used in future tasks) for correcting the waste loading and the w/cm ratio of the as-batched mixes in those cases where bleed liquid is present. For example, the Deliquification, Dissolution and Adjustment (DDA) mix at an as-batched 0.60 w/cm ratio, when corrected for % bleed, gives a mix with a 0.55 w/cm ratio and a WL that has been reduced from 662 to 625 mL/L. An example is provided that

Lysimeter study of vegetative uptake from saltstone

Energy Technology Data Exchange (ETDEWEB)

Murphy, C.E. Jr.

1990-06-08

At the Savannah River Site, liquid, low-level nuclear waste will be disposed of by incorporating the waste in concrete, a wasteform called saltstone. Saltstone monoliths will then be buried in the earth. To study the potential uptake of radionuclides by trees and other plants growing in the soil in the area containing buried saltstone, a lysimeter study has been in progress since 1984. Thirty two lysimeters were designed, constructed, and filled with soil. Saltstone samples, containing the liquid, low-level supernate from the tank 50 in-tank precipitation demonstration, were buried in some of the lysimeters. Other lysimeters, not containing saltstone, were used as controls. Crops, grass, and trees were planted in the lysimeters and sampled periodically to determine radionuclide concentrations. Water samples were also collected from the lysimeter sumps and analyzed for radionuclide content. This report documents the results of vegetative and lysimeter sump water measurements from the beginning of the project in November of 1984 through September of 1989. 6 refs., 22 figs., 6 tabs.

Leaching of saltstone: Laboratory and field testing and mathematical modeling

International Nuclear Information System (INIS)

Grant, M.W.; Langton, C.A.; Oblath, S.B.; Pepper, D.W.; Wallace, R.M.; Wilhite, E.L.; Yau, W.W.F.

1987-01-01

A low-level alkaline salt solution will be a byproduct in the processing of high-level waste at the Savannah River Plant (SRP). This solution will be incorporated into a wasteform, saltstone, and disposed of in surface vaults. Laboratory and field leach testing and mathematical modeling have demonstrated the predictability of contaminant release from cement wasteforms. Saltstone disposal in surface vaults will meet the design objective, which is to meet drinking water standards in shallow groundwater at the disposal area boundary. Diffusion is the predominant mechanism for release of contaminants to the environment. Leach testing in unsaturated soil, at soil moisture levels above 1 wt %, has shown no difference in leach rate compared to leaching in distilled water. Field leach testing of three thirty-ton blocks of saltstone in lysimeters has been underway since January 1984. Mathematical models were applied to assess design features for saltstone disposal. One dimensional infinite-composite and semi-infinite analytical models were developed for assessing diffusion of nitrate from saltstone through a cement barrier. Numerical models, both finite element and finite difference, were validated by comparison of model predictions with the saltstone lysimeter results. Validated models were used to assess the long-term performance of the saltstone stored in surface vaults. The maximum concentrations of all contaminants released from saltstone to shallow groundwater are predicted to be below drinking water standards at the disposal area boundary. 5 refs., 11 figs., 5 tabs

Nitrate Diffusional Releases from the Saltstone Facility, Vault 2, with Respect to Different Concrete Wall Thicknesses

International Nuclear Information System (INIS)

ROBERT, HIERGESELL

2005-01-01

To assist the Saltstone Vault 2 Design Team, an investigation was conducted to evaluate the effectiveness of alternative concrete wall thicknesses in limiting nitrate diffusion away from the planned facility. While the current design calls for 18-inch concrete walls, alternative thicknesses of 12-in, 8-in, and 6-in were evaluated using a simplified 1-D numerical model. To serve as a guide for Saltstone Vault 2 conceptual design, the results of this investigation were applied to Saltstone Vault 4 to determine what the hypothetical limits would be for concrete wall thicknesses thinner than the planned 18-inches. This was accomplished by adjusting the Vault 4 Limits, based on the increased nitrate diffusion rates through the thinner concrete walls, such that the 100-m well limit of 44 mg/L of nitrate as nitrate was not exceeded. The implication of these preliminary results is that as thinner vault walls are implemented there is a larger release of nitrate, thus necessitating optimal vault placement to minimize the number of vaults placed along a single groundwater flow path leading to the discharge zone

Leaching of saltstones containing fly ash

International Nuclear Information System (INIS)

Barnes, M.W.; Roy, D.M.; Langton, C.A.

1985-01-01

Two types of fly ash were incorporated in saltstones designed for potential encapsulation of Savannah River Plant low level defense waste. These fly ashes have some cementitious properties while at the same time their presence in substitution for cement slows early hydration. Class C fly ash has a high calcium content and is considered cementitious; Class F fly ash has a low calcium content and is not classified as cementitious. Leach tests were performed and physical properties were measured for saltstones containing each class, to see the differences in the effect of the fly ashes. The four waste ions nitrate, nitrite, sodium and sulfate were shown to leach by diffusion. Effective diffusivities were determined for these ions. Data for nitrate, the most important species from the environmental point of view, are shown in Table A. Saltstones made with Class C fly ash have substantially lower leach rates than those made with Class F fly ash. The leach rates, and therefore the square roots of the effective diffusivities, have been found to be proportional to the pore surface area per unit volume (or the ratio of pore volume to pore radius), to the fraction of waste containing solution, and to the inverse of the fraction of calcium in the saltstone. Rates and diffusivities are not proportional to the water to cement ratio, because this number depends on whether the fly ash is counted as cementitious, as in Class C cement, or not cementitious, as in Class F cement. In fact the relatively small amount of calcium in Class F cement contributes to the cementitious properties overall, though not so much as Class C cement. 4 refs., 2 figs., 6 tabs

Process Formulations And Curing Conditions That Affect Saltstone Properties

Energy Technology Data Exchange (ETDEWEB)

Reigel, M. M.; Pickenheim, B. R.; Daniel, W. E.

2012-09-28

The first objective of this study was to analyze saltstone fresh properties to determine the feasibility of reducing the formulation water to premix (w/p) ratio while varying the amount of extra water and admixtures used during processing at the Saltstone Production Facility (SPF). The second part of this study was to provide information for understanding the impact of curing conditions (cure temperature, relative humidity (RH)) and processing formulation on the performance properties of cured saltstone.

Concept development for saltstone and low level waste disposal

International Nuclear Information System (INIS)

Wilhite, E.L.

1987-03-01

A low-level alkaline salt solution will be a byproduct in the processing of high-level waste at the Savannah River Plant (SRP). This solution will be incorporated into a cement wasteform, saltstone, and placed in surface vaults. Laboratory and field testing and mathematical modeling have demonstrated the predictability of contaminant release from cement wasteforms. Saltstone disposal in surface vaults will meet drinking water standards in shallow groundwater at the disposal area boundary. Planning for new Low-Level Waste (LLW) disposal could incorporate concepts developed for saltstone disposal

Leaching Behavior of Heavy Metals from Cement Pastes Using a Modified Toxicity Characteristic Leaching Procedure (TCLP).

Science.gov (United States)

Huang, Minrui; Feng, Huajun; Shen, Dongsheng; Li, Na; Chen, Yingqiang; Shentu, Jiali

2016-03-01

As the standard toxicity characteristic leaching procedure (TCLP) can not exhaust the acid neutralizing capacity of the cement rotary kiln co-processing solid wastes products which is particularly important for the assessment of the leaching concentrations of heavy metals. A modified TCLP was proposed. The extent of leaching of heavy metals is low using the TCLP and the leaching performance of the different metals can not be differentiated. Using the modified TCLP, however, Zn leaching was negligible during the first 180 h and then sharply increased (2.86 ± 0.18 to 3.54 ± 0.26 mg/L) as the acidity increased (pH leaching is enhanced using the modified TCLP. While Pb leached readily during the first 126 h and then leachate concentrations decreased to below the analytical detection limit. To conclude, this modified TCLP is a more suitable method for these cement rotary kiln co-processing products.

Saltstone studies using the scaled continuous processing facility

Energy Technology Data Exchange (ETDEWEB)

Fowley, M. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hansen, E. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-08-01

The Savannah River National Laboratory (SRNL) has supported the Saltstone Facility since its conception with bench-scale laboratory experiments, mid-scale testing at vendor facilities, and consultations and testing at the Saltstone Facility. There have been minimal opportunities for the measurement of rheological properties of the grout slurry at the Saltstone Production Facility (SPF); thus, the Scaled Continuous Processing Facility (SCPF), constructed to provide processing data related to mixing, transfer, and other operations conducted in the SPF, is the most representative process data for determining the expected rheological properties in the SPF. These results can be used to verify the laboratory scale experiments that support the SPF using conventional mixing processes that appropriately represent the shear imparted to the slurry in the SPF.

Development and Implementation of a Scaled Saltstone Facility at Savannah River National Laboratory - 13346

International Nuclear Information System (INIS)

Reigel, Marissa M.; Fowley, Mark D.; Hansen, Erich K.; Hera, Kevin R.; Marzolf, Athneal D.; Cozzi, Alex D.

2013-01-01

The Savannah River National Laboratory (SRNL) has supported the Saltstone Production Facility (SPF) since its conception. However, bench scaled tests have not always provided process or performance data related to the mixing, transfer, and other operations utilized in the SPF. A need was identified to better understand the SPF processes and to have the capabilities at SRNL to simulate the SPF unit operations to support an active low-level radioactive waste (LLW) processing facility. At the SPF, the dry premix is weighed, mixed and transferred to the Readco '10-inch' continuous mixer where it is mixed with the LLW salt solution from the Salt Feed Tank (SFT) to produce fresh Saltstone slurry. The slurry is discharged from the mixer into a hopper. The hopper feeds the grout pump that transfers the slurry through at least 457.2 meters of piping and discharges it into the Saltstone Disposal Units (SDU) for permanent disposal. In conjunction with testing individual SPF processes over several years, SRNL has designed and fabricated a scaled Saltstone Facility. Scaling of the system is primarily based on the volume capacity of the mixer and maintaining the same shear rate and total shear at the wall of the transfer line. At present, SRNL is utilizing the modular capabilities of the scaled Saltstone Facility to investigate the erosion issues related to the augers and paddles inside the SPF mixer. Full implementation of the scaled Saltstone Facility is still ongoing, but it is proving to be a valuable resource for testing alternate Saltstone formulations, cleaning sequences, the effect of pumping Saltstone to farther SDU's, optimization of the SPF mixer, and other operational variables before they are implemented in the SPF. (authors)

Verification of Sulfate Attack Penetration Rates for Saltstone Disposal Unit Modeling

Energy Technology Data Exchange (ETDEWEB)

Flach, G. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-05-12

Recent Special Analysis modeling of Saltstone Disposal Units consider sulfate attack on concrete and utilize degradation rates estimated from Cementitious Barriers Partnership software simulations. This study provides an independent verification of those simulation results using an alternative analysis method and an independent characterization data source. The sulfate penetration depths estimated herein are similar to the best-estimate values in SRNL-STI-2013-00118 Rev. 2 and well below the nominal values subsequently used to define Saltstone Special Analysis base cases.

Large-scale demonstration of waste solidification in saltstone

International Nuclear Information System (INIS)

McIntyre, P.F.; Oblath, S.B.; Wilhite, E.L.

1988-05-01

The saltstone lysimeters are a large scale demonstration of a disposal concept for decontaminated salt solution resulting from in-tank processing of defense waste. The lysimeter experiment has provided data on the leaching behavior of large saltstone monoliths under realistic field conditions. The results also will be used to compare the effect of capping the wasteform on contaminant release. Biweekly monitoring of sump leachate from three lysimeters has continued on a routine basis for approximately 3 years. An uncapped lysimeter has shown the highest levels of nitrate and 99 Tc release. Gravel and clay capped lysimeters have shown levels equivalent to or slightly higher than background rainwater levels. Mathematical model predictions have been compared to lysimeter results. The models will be applied to predict the impact of saltstone disposal on groundwater quality. 9 refs., 5 figs., 3 tabs

Degradation Of Cementitious Materials Associated With Saltstone Disposal Units

International Nuclear Information System (INIS)

Flach, G. P; Smith, F. G. III

2013-01-01

(CE) and more defensible than the best estimate (BE). The combined effects of multiple phenomena are then considered to determine the most limiting degradation time scale for each cementitious material. Degradation times are estimated using a combination of analytic solutions from literature and numerical simulation codes provided through the DOE Cementitious Barriers Partnership (CBP) Software Toolbox (http://cementbarriers.org). For the SDU 2 design, the roof, wall, and floor components are projected to become fully degraded under Nominal conditions at 3866, 923, and 1413 years, respectively. For SDU 4 the roof and floor are estimated to be fully degraded under Nominal conditions after 1137 and 1407 years, respectively; the wall is assumed to be fully degraded at time zero in the most recent PA simulations. Degradation of these concrete barriers generally occurs from combined sulfate attack and corrosion of embedded steel following carbonation. Saltstone is projected to degrade very slowly by decalcification, with complete degradation occurring in excess of 200,000 years for any SDU type. Complete results are provided

Technical Insights for Saltstone PA Maintenance

International Nuclear Information System (INIS)

Flach, G.; Sarkar, S.; Mahadevan, S.; Kosson, D.

2011-01-01

The Cementitious Barriers Partnership (CBP) is a collaborative program sponsored by the US DOE Office of Waste Processing. The objective of the CBP is to develop a set of computational tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers and waste forms used in nuclear applications. CBP tools are expected to better characterize and reduce the uncertainties of current methodologies for assessing cementitious barrier performance and increase the consistency and transparency of the assessment process, as the five-year program progresses. In September 2009, entering its second year of funded effort, the CBP sought opportunities to provide near-term tangible support to DOE Performance Assessments (PAs). The Savannah River Saltstone Disposal Facility (SDF) was selected for the initial PA support effort because (1) cementitious waste forms and barriers play a prominent role in the performance of the facility, (2) certain important long-term behaviors of cementitious materials composing the facility are uncertain, (3) review of the SDF PA by external stakeholders is ongoing, and (4) the DOE contractor responsible for the SDF PA is open to receiving technical assistance from the CBP. A review of the current (SRR Closure and Waste Disposal Authority 2009) and prior Saltstone PAs (e.g., Cook et al. 2005) suggested five potential opportunities for improving predictions. The candidate topics considered were (1) concrete degradation from external sulfate attack, (2) impact of atmospheric exposure to concrete and grout before closure, such as accelerated slag and Tc-99 oxidation, (3) mechanistic prediction of geochemical conditions, (4) concrete degradation from rebar corrosion due to carbonation, and (5) early age cracking from drying and/or thermal shrinkage. The candidate topics were down-selected considering the feasibility of addressing each issue within approximately six months, and

Technical Insights for Saltstone PA Maintenance

Energy Technology Data Exchange (ETDEWEB)

Flach, G.; Sarkar, S.; Mahadevan, S.; Kosson, D.

2011-07-20

The Cementitious Barriers Partnership (CBP) is a collaborative program sponsored by the US DOE Office of Waste Processing. The objective of the CBP is to develop a set of computational tools to improve understanding and prediction of the long-term structural, hydraulic, and chemical performance of cementitious barriers and waste forms used in nuclear applications. CBP tools are expected to better characterize and reduce the uncertainties of current methodologies for assessing cementitious barrier performance and increase the consistency and transparency of the assessment process, as the five-year program progresses. In September 2009, entering its second year of funded effort, the CBP sought opportunities to provide near-term tangible support to DOE Performance Assessments (PAs). The Savannah River Saltstone Disposal Facility (SDF) was selected for the initial PA support effort because (1) cementitious waste forms and barriers play a prominent role in the performance of the facility, (2) certain important long-term behaviors of cementitious materials composing the facility are uncertain, (3) review of the SDF PA by external stakeholders is ongoing, and (4) the DOE contractor responsible for the SDF PA is open to receiving technical assistance from the CBP. A review of the current (SRR Closure & Waste Disposal Authority 2009) and prior Saltstone PAs (e.g., Cook et al. 2005) suggested five potential opportunities for improving predictions. The candidate topics considered were (1) concrete degradation from external sulfate attack, (2) impact of atmospheric exposure to concrete and grout before closure, such as accelerated slag and Tc-99 oxidation, (3) mechanistic prediction of geochemical conditions, (4) concrete degradation from rebar corrosion due to carbonation, and (5) early age cracking from drying and/or thermal shrinkage. The candidate topics were down-selected considering the feasibility of addressing each issue within approximately six months, and

Investigations of metal leaching from mobile phone parts using TCLP and WET methods.

Science.gov (United States)

Yadav, Satyamanyu; Yadav, Sudesh

2014-11-01

Metal leaching from landfills containing end-of-life or otherwise discarded mobile phones poses a threat to the environment as well as public health. In the present study, the metal toxicity of printed wire boards (PWBs), plastics, liquid crystal displays (LCDs) and batteries of mobile phones was assessed using the Toxicity Characteristics Leaching Procedures (TCLP) and the Waste Extraction Test (WET). The PWBs failed TCLP for Pb and Se, and WET for Pb and Zn. In WET, the two PWB samples for Pb and Zn and the battery samples for Co and Cu failed the test. Furthermore, the PWBS for Ni and the battery samples for Ni and Co failed the WET in their TCLP leachates. Both, Ni and Co are the regulatory metals in only WET and not covered under TCLP. These observations indicate that the TCLP seems to be a more aggressive test than the WET for the metal leaching from the mobile phone parts. The compositional variations, nature of leaching solution (acetate in TCLP and citrate in WET) and the redox conditions in the leaching solution of the PWBs resulted in different order of metals with respect to their amounts of leaching from PWBs in TCLP (Fe > Pb > Zn > Ni > Co > Cu) and WET (Zn > Fe > Ni > Pb > Cu). The metal leaching also varied with the make, manufacturing year and part of the mobile phone tested. PWBs, plastics and batteries should be treated as hazardous waste. Metal leaching, particularly of Se and Pb, from mobile phones can be harmful to the environment and human health. Therefore, a scientifically sound and environmentally safe handling and disposal management system needs to be evolved for the mobile phone disposal. Copyright © 2014 Elsevier Ltd. All rights reserved.

Degradation Of Cementitious Materials Associated With Saltstone Disposal Units

Energy Technology Data Exchange (ETDEWEB)

Flach, G. P; Smith, F. G. III

2013-03-19

estimate (CE) and more defensible than the best estimate (BE). The combined effects of multiple phenomena are then considered to determine the most limiting degradation time scale for each cementitious material. Degradation times are estimated using a combination of analytic solutions from literature and numerical simulation codes provided through the DOE Cementitious Barriers Partnership (CBP) Software Toolbox (http://cementbarriers.org). For the SDU 2 design, the roof, wall, and floor components are projected to become fully degraded under Nominal conditions at 3866, 923, and 1413 years, respectively. For SDU 4 the roof and floor are estimated to be fully degraded under Nominal conditions after 1137 and 1407 years, respectively; the wall is assumed to be fully degraded at time zero in the most recent PA simulations. Degradation of these concrete barriers generally occurs from combined sulfate attack and corrosion of embedded steel following carbonation. Saltstone is projected to degrade very slowly by decalcification, with complete degradation occurring in excess of 200,000 years for any SDU type. Complete results are provided.

EVALUATION OF SULFATE ATTACK ON SALTSTONE VAULT CONCRETE AND SALTSTONESIMCO TECHNOLOGIES, INC. PART1 FINAL REPORT

International Nuclear Information System (INIS)

Langton, C.

2008-01-01

This report summarizes the preliminary results of a durability analysis performed by SIMCO Technologies Inc. to assess the effects of contacting saltstone Vaults 1/4 and Disposal Unit 2 concretes with highly alkaline solutions containing high concentrations of dissolved sulfate. The STADIUM(reg s ign) code and data from two surrogate concretes which are similar to the Vaults 1/4 and Disposal Unit 2 concretes were used in the preliminary durability analysis. Simulation results for these surrogate concrete mixes are provided in this report. The STADIUM(reg s ign) code will be re-run using transport properties measured for the SRS Vaults 1/4 and Disposal Unit 2 concrete samples after SIMCO personnel complete characterization testing on samples of these materials. Simulation results which utilize properties measured for samples of Vaults 1/4 and Disposal Unit 2 concretes will be provided in Revision 1 of this report after property data become available. The modeling performed to date provided the following information on two concrete mixes that will be used to support the Saltstone PA: (1) Relationship between the rate of advancement of the sulfate front (depth of sulfate ion penetration into the concrete) and the rate of change of the concrete permeability and diffusivity. (2) Relationship between the sulfate ion concentration in the corrosive leachate and the rate of the sulfate front progression. (3) Equation describing the change in hydraulic properties (hydraulic conductivity and diffusivity) as a function of sulfate ion concentration in the corrosive leachate. These results have been incorporated into the current Saltstone PA analysis by G. Flach (Flach, 2008). In addition, samples of the Saltstone Vaults 1/4 and Disposal Unit 2 concretes have been prepared by SIMCO Technologies, Inc. Transport and physical properties for these materials are currently being measured and sulfate exposure testing to three high alkaline, high sulfate leachates provided by SRNL is

FOAM FORMATION IN THE SALTSTONE PRODUCTION FACILITY: EVALUATION OF SOURCES AND MITIGATION

Energy Technology Data Exchange (ETDEWEB)

Cozzi, A.

2011-01-18

The Saltstone Production Facility receives waste from Tank 50H for treatment. Influents into Tank 50H include the Effluent Treatment Project waste concentrate, H-Canyon low activity waste and General Purpose Evaporator bottoms, Modular Caustic Side Solvent Extraction Unit decontaminated salt solution, and salt solution from the Deliquification, Dissolution and Adjust campaign. Using the Waste Characterization System (WCS), this study tracks the relative amounts of each influent into Tank 50H, as well as the total content of Tank 50H, in an attempt to identify the source of foaming observed in the Saltstone Production Facility hopper. Saltstone has been using antifoam as part of routine processing with the restart of the facility in December 2006. It was determined that the maximum admix usage in the Saltstone Production Facility, both antifoam and set retarder, corresponded with the maximum concentration of H-Canyon low activity waste in Tank 50H. This paper also evaluates archived salt solutions from Waste Acceptance Criteria analysis for propensity to foam and the antifoam dosage required to mitigate foaming. It was determined that Effluent Treatment Project contributed to the expansion factor (foam formation) and General Purpose Evaporator contributed to foaminess (persistence). It was also determined that undissolved solids contribute to foam persistence. It was shown that additions of Dow Corning Q2-1383a antifoam reduced both the expansion factor and foaminess of salt solutions. The evaluation of foaming in the grout hopper during the transition from water to salt solution indicated that higher water-to-premix ratios tended to produce increased foaming. It was also shown that additions of Dow Corning Q2-1383a antifoam reduced foam formation and persistence.

Savannah River Site - Salt-stone Disposal Facility Performance Assessment Update

International Nuclear Information System (INIS)

Newman, J.L.

2009-01-01

The Savannah River Site (SRS) Salt-stone Facility is currently in the midst of a Performance Assessment revision to estimate the effect on human health and the environment of adding new disposal units to the current Salt-stone Disposal Facility (SDF). These disposal units continue the ability to safely process the salt component of the radioactive liquid waste stored in the underground storage tanks at SRS, and is a crucial prerequisite for completion of the overall SRS waste disposition plan. Removal and disposal of low activity salt waste from the SRS liquid waste system is required in order to empty tanks for future tank waste processing and closure operations. The Salt-stone Production Facility (SPF) solidifies a low-activity salt stream into a grout matrix, known as salt-stone, suitable for disposal at the SDF. The ability to dispose of the low-activity salt stream in the SDF required a waste determination pursuant to Section 3116 of the Ronald Reagan National Defense Authorization Act of 2005 and was approved in January 2006. One of the requirements of Section 3116 of the NDAA is to demonstrate compliance with the performance objectives set out in Subpart C of Part 61 of Title 10, Code of Federal Regulations. The PA is the document that is used to ensure ongoing compliance. (authors)

Modified TCLP test for evaluating the leachability of site-specific wastes

International Nuclear Information System (INIS)

Pier, J.

1996-01-01

The Weldon Spring Site Remedial Action Project (WSSRAP) has developed a site-specific test to assess the leachability of wastes that will be placed in its on-site disposal cell. This test is modelled after the TCLP, but examines an expanded list of parameters and uses an extraction solution that is representative of conditions that are expected to exist in the disposal facility. Following the same logic that guided development of TCLP protocols, the WSSRAP developed concentration guidelines for non-TCLP parameters that were contaminants of concern in its wastes. Response actions, specific to the WSSRAP cell and wastes, were also developed to address constituents that failed to meet these guides. From 1955 to 1966, the US Atomic Energy Commission operated a uranium feed materials plant on this site. Nitroaromatic, and later, radiological wastes were disposed of in the quarry from 1945 until 1970. This paper describes testing to determine whether contaminant concentrations in leachates derived from the major waste-types that will be placed in its on-site disposal cell conform with the Department of Energy's (DOE) as low as reasonably achievable (ALARA) policy. Although the WSSRAP will continue to use the TCLP test to determine if any waste is classified RCRA-hazardous, the site-specific test described in this paper will be used to further assess whether leachate from any waste-type has the potential to adversely impact groundwater

TCLP Preparation and Analysis of K East Basin Composite Sludge Samples

International Nuclear Information System (INIS)

Silvers, K.L.; Wagner, J.J.; Steele, R.T.

2000-01-01

Sludge samples from the Hanford K East Basin were analyzed by the Toxicity Characterization Leaching Procedure (TCLP) to assist in the appropriate Resource Conservation and Recovery Act (RCIL4) designation of this material. Sludge samples were collected by Fluor Hanford, Inc. using the consolidated sludge sampling system (system that allows collection of a single sample from multiple sample locations). These samples were shipped to the Postirradiation Testing Laboratory (PTL, 327 Building) and then transferred to the Pacific Northwest National Laboratory (PNNL) Radiochemical Processing Laboratory (RPL, 325 Building) for recovery and testing. Two sludge composites were prepared, using the consolidated sludge samples, to represent K East canister sludge (sample KC Can Comp) and K East floor sludge (sample KC Floor Comp). Each composite was extracted in duplicate and analyzed in duplicate following pre-approved(a) TCLP extraction and analyses procedures. In addition, these samples and duplicates were analyzed for total RCRA metals (via acid digestion preparation). The work was conducted in accordance with the requirements of the Hanford Analytical Quality Assurance Requirements Document (HASQARD). A PNNL Quality Assurance Program compliant with J HASQARD was implemented for this effort. The results from the TCLP analyses showed that all RCRA metal concentrations were less than the TCLP limits for both the canister and floor composite samples and their respective duplicates

Method Evaluation And Field Sample Measurements For The Rate Of Movement Of The Oxidation Front In Saltstone

Energy Technology Data Exchange (ETDEWEB)

Almond, P. M. [Savannah River Site (SRS), Aiken, SC (United States); Kaplan, D. I. [Savannah River Site (SRS), Aiken, SC (United States); Langton, C. A. [Savannah River Site (SRS), Aiken, SC (United States); Stefanko, D. B. [Savannah River Site (SRS), Aiken, SC (United States); Spencer, W. A. [Savannah River Site (SRS), Aiken, SC (United States); Hatfield, A. [Clemson University, Clemson, SC (United States); Arai, Y. [Clemson University, Clemson, SC (United States)

2012-08-23

The objective of this work was to develop and evaluate a series of methods and validate their capability to measure differences in oxidized versus reduced saltstone. Validated methods were then applied to samples cured under field conditions to simulate Performance Assessment (PA) needs for the Saltstone Disposal Facility (SDF). Four analytical approaches were evaluated using laboratory-cured saltstone samples. These methods were X-ray absorption spectroscopy (XAS), diffuse reflectance spectroscopy (DRS), chemical redox indicators, and thin-section leaching methods. XAS and thin-section leaching methods were validated as viable methods for studying oxidation movement in saltstone. Each method used samples that were spiked with chromium (Cr) as a tracer for oxidation of the saltstone. The two methods were subsequently applied to field-cured samples containing chromium to characterize the oxidation state of chromium as a function of distance from the exposed air/cementitious material surface.

Special Analysis: Revision of Saltstone Vault 4 Disposal Limits (U)

Energy Technology Data Exchange (ETDEWEB)

Cook, J

2005-05-26

New disposal limits have been computed for Vault 4 of the Saltstone Disposal Facility based on several revisions to the models in the existing Performance Assessment and the Special Analysis issued in 2002. The most important changes are the use of a more rigorous groundwater flow and transport model, and consideration of radon emanation. Other revisions include refinement of the aquifer mesh to more accurately model the footprint of the vault, a new plutonium chemistry model accounting for the different transport properties of oxidation states III/IV and V/VI, use of variable infiltration rates to simulate degradation of the closure system, explicit calculation of gaseous releases and consideration of the effects of settlement and seismic activity on the vault structure. The disposal limits have been compared with the projected total inventory expected to be disposed in Vault 4. The resulting sum-of-fractions of the 1000-year disposal limits is 0.2, which indicates that the performance objectives and requirements of DOE 435.1 will not be exceeded. This SA has not altered the conceptual model (i.e., migration of radionuclides from the Saltstone waste form and Vault 4 to the environment via the processes of diffusion and advection) of the Saltstone PA (MMES 1992) nor has it altered the conclusions of the PA (i.e., disposal of the proposed waste in the SDF will meet DOE performance measures). Thus a PA revision is not required and this SA serves to update the disposal limits for Vault 4. In addition, projected doses have been calculated for comparison with the performance objectives laid out in 10 CFR 61. These doses are 0.05 mrem/year to a member of the public and 21.5 mrem/year to an inadvertent intruder in the resident scenario over a 10,000-year time-frame, which demonstrates that the 10 CFR 61 performance objectives will not be exceeded. This SA supplements the Saltstone PA and supersedes the two previous SAs (Cook et al. 2002; Cook and Kaplan 2003).

Lessons Learned from an External Review of the Savannah River Site Saltstone Performance Assessment Program

International Nuclear Information System (INIS)

Cook, J.R.

2006-01-01

The Savannah River National Laboratory is actively working on a total revision of the Saltstone Performance Assessment. 'Lessons Learned' from the review are being applied to this effort. Examples of the areas in which significant new work is being done are development of a methodology to do probabilistic uncertainty analyses, employing quantitative analytical tools to represent long-term chemical degradation of both concrete and the Saltstone wasteform, and then using those tools to come to a better understanding of how changes in the vault and Saltstone will affect the performance of the overall disposal system over long periods of time. (authors)

Saltstone processing startup at the Savannah River Plant

International Nuclear Information System (INIS)

Wilhite, E.L.; Langton, C.A.; Sturm, H.F.; Hooker, R.L.; Occhipinti, E.S.

1988-01-01

High-level nuclear wastes are stored in large underground tanks at the Savannah River Plant. Processing of this waste in preparation for ultimate disposal will begin in 1988. The waste will be processed to separate the high-level radioactive fraction from the low-level radioactive fraction. The separation will be made in existing waste tanks by a process combining precipitation, adsorption, and filtration. The high-level fraction will be vitrified into borosilicate glass in the Defense Waste Processing Facility (DWPF) for permanent disposal in a federal repository. The low-level fraction (decontaminated salt solution) will be mixed with a cementitious slag-flyash blend. The resulting wasteform, saltstone, will be disposed of onsite by emplacement in an engineered facility. Waste properties, disposal facility details, and wasteform characteristics are discussed. In particular, details of saltstone processing, focusing on experience obtained from facility startup, are presented

Evaluation of ISDP Batch 2 Qualification Compliance to 512-S, DWPF, Tank Farm, and Saltstone Waste Acceptance Criteria

Energy Technology Data Exchange (ETDEWEB)

Shafer, A.

2010-05-05

The purpose of this report is to document the acceptability of the second macrobatch (Salt Batch 2) of Tank 49H waste to H Tank Farm, DWPF, and Saltstone for operation of the Interim Salt Disposition Project (ISDP). Tank 49 feed meets the Waste Acceptance Criteria (WAC) requirements specified by References 11, 12, and 13. Salt Batch 2 material is qualified and ready to be processed through ARP/MCU to the final disposal facilities.

SALTSTONE VARIABILITY STUDY - MEASUREMENT OF POROSITY

International Nuclear Information System (INIS)

Harbour, J; Vickie Williams, V; Tommy Edwards, T; Russell Eibling, R; Ray Schumacher, R

2007-01-01

One of the goals of the Saltstone Variability Study is to identify the operational and compositional variables that control or influence the important processing and performance properties of Saltstone mixes. One of the key performance properties is porosity which is a measure of the volume percent of a cured grout that is occupied by salt solution (for the saturated case). This report presents (1) the results of efforts to develop a method for the measurement of porosity of grout samples and (2) initial results of porosity values for samples that have been previously produced as part of the Saltstone Variability Study. A cost effective measurement method for porosity was developed that provides reproducible results, is relatively fast (30 to 60 minutes per sample) and uses a Mettler Toledo HR83 Moisture Analyzer that is already operational and routinely calibrated at Aiken County Technology Laboratory. The method involves the heating of the sample at 105 C until no further mass loss is observed. This mass loss value, which is due to water evaporation, is then used to calculate the volume percent porosity of the mix. The results of mass loss for mixes at 105 C were equivalent to the results obtained using thermal gravimetric analysis. The method was validated by comparing measurements of mass loss at 105 C for cured portland cement in water mixes to values presented in the literature for this system. A stereopycnometer from Quantachrome Instruments was selected to measure the cured grout bulk densities. Density is a property that is required to calculate the porosities. A stereopycnometer was already operational at Aiken County Technology Laboratory, has been calibrated using a solid stainless steel sphere of known volume, is cost effective and fast (∼15 minutes per sample). Cured grout densities are important in their own right because they can be used to project the volume of waste form produced from a given amount of salt feed of known composition. For mixes

Evaluation of Proposed New LLW Disposal Activity: Disposal of Aqueous PUREX Waste Stream in the Saltstone Disposal Facility

International Nuclear Information System (INIS)

Cook, J.R.

2003-01-01

The Aqueous PUREX waste stream from Tanks 33 and 35, which have been blended in Tank 34, has been identified for possible processing through the Saltstone Processing Facility for disposal in the Saltstone Disposal Facility

Estimated release from the saltstone landfill effect of landfill caps and landfill-cap/monolith-liner combinations

International Nuclear Information System (INIS)

Wilhite, E.L.

1985-01-01

The effect of capping the entire saltstone landfill is dependent on the effectiveness of the clay cap in preventing infiltration. A cap that is 99% effective will reduce releases from the saltstone landfill by a factor of 7.7. Several combinations of landfill design alterations will result in meeting ground water standards

Key Factors That Influence The Performance Properties Of ARP/MCU Saltstone Mixes

International Nuclear Information System (INIS)

Harbour, J.; Edwards, T.; Williams, V.

2009-01-01

At the Saltstone Production Facility (SPF), decontaminated salt solution (DSS) is combined with premix (a cementitious mixture of portland cement (PC), blast furnace slag (BFS) and Class F fly ash (FA)) in a Readco mixer to produce fresh (uncured) Saltstone. After transfer to the Saltstone Disposal Facility (SDF) the hydration reactions initiated during the contact of the premix and salt solution continue during the curing period to produce the hardened waste form product. The amount of heat generated from hydration and the resultant temperature increase in the vaults depend on the composition of the decontaminated salt solution being dispositioned as well as the grout formulation (mix design). This report details the results from Task 3 of the Saltstone Variability Study for FY09 which was performed to identify, and quantify when possible, those factors that drive the performance properties of the projected ARP/MCU Batches. A baseline ARP/MCU mix (at 0.60 water to cementitious materials (w/cm) ratio) was established and consisted of the normal premix composition and a salt solution that was an average of the projected compositions of the last three ARP/MCU batches developed by T. A. Le. This task introduced significant variation in (1) wt % slag, w/cm ratio, and wt % portland cement about the baseline mix and (2) the temperature of curing in order to better assess the dependence of the performance properties on these factors. Two separate campaigns, designated Phase 10 and Phase 11, were carried out under Task 3. Experimental designs and statistical analyses were used to search for correlation among properties and to develop linear models to predict property values based on factors such as w/cm ratio, slag concentration, and portland cement concentration. It turns out that the projected salt compositions contained relatively high amounts of aluminate (0.22 M) even though no aluminate was introduced due to caustic aluminate removal from High Level Waste. Previous

Composite analysis E-area vaults and saltstone disposal facilities

Energy Technology Data Exchange (ETDEWEB)

Cook, J.R.

1997-09-01

This report documents the Composite Analysis (CA) performed on the two active Savannah River Site (SRS) low-level radioactive waste (LLW) disposal facilities. The facilities are the Z-Area Saltstone Disposal Facility and the E-Area Vaults (EAV) Disposal Facility. The analysis calculated potential releases to the environment from all sources of residual radioactive material expected to remain in the General Separations Area (GSA). The GSA is the central part of SRS and contains all of the waste disposal facilities, chemical separations facilities and associated high-level waste storage facilities as well as numerous other sources of radioactive material. The analysis considered 114 potential sources of radioactive material containing 115 radionuclides. The results of the CA clearly indicate that continued disposal of low-level waste in the saltstone and EAV facilities, consistent with their respective radiological performance assessments, will have no adverse impact on future members of the public.

Composite analysis E-area vaults and saltstone disposal facilities

International Nuclear Information System (INIS)

Cook, J.R.

1997-09-01

This report documents the Composite Analysis (CA) performed on the two active Savannah River Site (SRS) low-level radioactive waste (LLW) disposal facilities. The facilities are the Z-Area Saltstone Disposal Facility and the E-Area Vaults (EAV) Disposal Facility. The analysis calculated potential releases to the environment from all sources of residual radioactive material expected to remain in the General Separations Area (GSA). The GSA is the central part of SRS and contains all of the waste disposal facilities, chemical separations facilities and associated high-level waste storage facilities as well as numerous other sources of radioactive material. The analysis considered 114 potential sources of radioactive material containing 115 radionuclides. The results of the CA clearly indicate that continued disposal of low-level waste in the saltstone and EAV facilities, consistent with their respective radiological performance assessments, will have no adverse impact on future members of the public

UK-Nuclear decommissioning authority and US Salt-stone waste management issues

International Nuclear Information System (INIS)

Lawless, William; Whitton, John

2007-01-01

Available in abstract form only. Full text of publication follows: We update two case studies of stakeholder issues in the UK and US. Earlier versions were reported at Waste Management 2006 and 2007 and at ICEM 2005. UK: The UK nuclear industry has begun to consult stakeholders more widely in recent years. Historically, methods of engagement within the industry have varied, however, recent discussions have generally been carried out with the explicit understanding that engagement with stakeholders will be 'dialogue based' and will 'inform' the final decision made by the decision maker. Engagement is currently being carried out at several levels within the industry; at the national level (via the Nuclear Decommissioning Authority's (NDA) National Stakeholder Group (NSG)); at a local site level (via Site Stakeholder Groups) and at a project level (usually via the Best Practicable Environmental Option process (BPEO)). This paper updates earlier results by the co-author with findings from a second questionnaire issued to the NSG in Phase 2 of the engagement process. An assessment is made regarding the development of stakeholder perceptions since Phase 1 towards the NDA process. US: The US case study reviews the resolution of issues on salt-stone by Department of Energy's (DOE) Savannah River Site (SRS) Citizens Advisory Board (CAB), in Aiken, SC. Recently, SRS-CAB encouraged DOE and South Carolina's regulatory Department of Health and Environmental Control (SC-DHEC) to resolve a conflict preventing SC-DHEC from releasing a draft permit to allow SRS to restart salt-stone operations. It arose with a letter sent from DOE blaming the Governor of South Carolina for delay in restarting salt processing. In reply, the Governor blamed DOE for failing to assure that Salt Waste Processing Facility (SWPF) would be built. SWPF is designed to remove most of the radioactivity from HLW prior to vitrification, the remaining fraction destined for salt-stone. (authors)

Groundwater Monitoring Plan for the Z-Area Saltstone Disposal Facility, Revision 3

International Nuclear Information System (INIS)

WELLS, DANIEL

2005-01-01

Groundwater monitoring has been conducted at the Z-Area Saltstone Disposal Facility since 1987. At that time, groundwater monitoring was not required by the industrial landfill regulations, but a modest monitoring program was required by the operating permit. At the time of the 1996 permit renewal, it was determined that a more robust monitoring program was needed. The draft permit required new monitoring wells within 25 feet of each active disposal cell. As an alternative, SRS proposed a program based on direct push sampling. This program called for biennial direct push sampling within 25 feet of each waste-containing cell with additional samples being taken in areas where excessive cracking had been observed. The direct push proposal was accepted by The South Carolina Department of Health and Environmental Control (SCDHEC), and was incorporated by reference into the Z-Area Saltstone Industrial Solid Waste Permit, No.025500-1603. The Industrial Solid Waste Landfill Regulations were revised in 1998 and now include specific requirements for groundwater monitoring. SRS's plan for complying with those regulations is discussed below. The plan calls for a return to traditional monitoring with permanent wells. It also proposes a more technically sound monitoring list based on the actual composition of saltstone

GAS MIXING ANALYSIS IN A LARGE-SCALED SALTSTONE FACILITY

Energy Technology Data Exchange (ETDEWEB)

Lee, S

2008-05-28

Computational fluid dynamics (CFD) methods have been used to estimate the flow patterns mainly driven by temperature gradients inside vapor space in a large-scaled Saltstone vault facility at Savannah River site (SRS). The purpose of this work is to examine the gas motions inside the vapor space under the current vault configurations by taking a three-dimensional transient momentum-energy coupled approach for the vapor space domain of the vault. The modeling calculations were based on prototypic vault geometry and expected normal operating conditions as defined by Waste Solidification Engineering. The modeling analysis was focused on the air flow patterns near the ventilated corner zones of the vapor space inside the Saltstone vault. The turbulence behavior and natural convection mechanism used in the present model were benchmarked against the literature information and theoretical results. The verified model was applied to the Saltstone vault geometry for the transient assessment of the air flow patterns inside the vapor space of the vault region using the potential operating conditions. The baseline model considered two cases for the estimations of the flow patterns within the vapor space. One is the reference nominal case. The other is for the negative temperature gradient between the roof inner and top grout surface temperatures intended for the potential bounding condition. The flow patterns of the vapor space calculated by the CFD model demonstrate that the ambient air comes into the vapor space of the vault through the lower-end ventilation hole, and it gets heated up by the Benard-cell type circulation before leaving the vault via the higher-end ventilation hole. The calculated results are consistent with the literature information. Detailed results and the cases considered in the calculations will be discussed here.

Design of saltstone vaults

International Nuclear Information System (INIS)

Aiyar, G.S.; Hsiu, F.J.

1987-01-01

Radioactive waste from processed spent nuclear fuel at the Savannah River Plant, South Carolina, are stored in underground tanks. The wastes consist of sludge and supernate. Most of the radionuclides and some nonradioactive constituents are removed from the supernate. These along with the sludge are converted into a glass-crystallite matrix and cast into stainless steel cansisters for future disposal in a geological repository. The decontaminated salt solution is mixed with cement, fly ash, and a set-retarding agent, and the resulting grout is transferred to reinforced concrete vaults where it sets into a monolith termed saltstone. The vault is then capped with concrete. A total of 21 vaults measuring 600 x 100 x 27 ft are planned for disposal of the existing supernate plus any additional supernate generated up to the year 2000

Atmospheric Pathway Screening Analysis for Saltstone Disposal Facility Vault 4

International Nuclear Information System (INIS)

COOK, JAMES

2004-01-01

A sequential screening process using a methodology developed by the National Council on Radiation Protection and Measurements, professional judgment and process knowledge has been used to produce a list of radionuclides requiring detailed analysis to derive disposal limits for the Saltstone Disposal Facility based on the atmospheric pathway

Computational Fluid Dynamics Model for Saltstone Vault 4 Vapor Space

International Nuclear Information System (INIS)

Lee, Si Young

2005-01-01

Computational fluid dynamics (CFD) methods have been used to estimate the flow patterns for vapor space inside the Saltstone Vault No.4 under different operating scenarios. The purpose of this work is to examine the gas motions inside the vapor space under the current vault configurations. A CFD model took three-dimensional transient momentum-energy coupled approach for the vapor space domain of the vault. The modeling calculations were based on prototypic vault geometry and expected normal operating conditions as defined by Waste Solidification Engineering. The modeling analysis was focused on the air flow patterns near the ventilated corner zones of the vapor space inside the Saltstone vault. The turbulence behavior and natural convection mechanism used in the present model were benchmarked against the literature information and theoretical results. The verified model was applied to the Saltstone vault geometry for the transient assessment of the air flow patterns inside the vapor space of the vault region using the boundary conditions as provided by the customer. The present model considered two cases for the estimations of the flow patterns within the vapor space. One is the reference baseline case. The other is for the negative temperature gradient between the roof inner and top grout surface temperatures intended for the potential bounding condition. The flow patterns of the vapor space calculated by the CFD model demonstrate that the ambient air comes into the vapor space of the vault through the lower-end ventilation hole, and it gets heated up by the Benard-cell type circulation before leaving the vault via the higher-end ventilation hole. The calculated results are consistent with the literature information

Benzene TCLP results from saltstone prepared with 2X ITP flowsheet concentrations of phenylborates

International Nuclear Information System (INIS)

Poirier, M.R.

2000-01-01

The Savannah River Site (SRS) teamed with the Pacific Northwest National Laboratory (PNNL), Oak Ridge National Laboratory (ORNL), and ITT Flygt Corporation to conduct a test program evaluating shrouded axial propeller mixers (Flygt mixers) for heel removal in SRS Tank 19. SRS is identifying and investigating techniques to remove sludge heels from waste tanks such as Tank 19

IMPACT OF INCREASED ALUMINATE CONCENTRATIONS ON PROPERTIES OF SALTSTONE MIXES

International Nuclear Information System (INIS)

Harbour, J; Tommy Edwards, T; Erich Hansen, E; Vickie Williams, V

2007-01-01

trends observed as the aluminate concentration increased in the salt solution were decreased Bingham Plastic yield stress and plastic viscosity, greater flowability of the grout, and reduced gel times and bleed volume for SWPF based mixes. On the other hand, the set times increased significantly with increasing aluminate concentration in the salt solutions. For the SWPF mixes, the set time increased from 1 to 4 days and for the Tank 11 mixes, the set time increased from 1 to 2 days. Heat of hydration measurements were consistent with the increased set times with extended induction periods (2 to 4 days) as aluminate concentration increased in the salt solution. This extended induction period of heat evolution observed with increasing aluminate concentrations must be addressed for Saltstone operations to avoid exceeding temperature limits. It is anticipated that the induction period will be temperature dependent and should be measured for future projections and included in the thermal modeling. The overall heat generation was greater in the mixes containing higher concentrations of aluminate. In fact, for the total heat release values calculated using curve fitting for longer times, the amount of heat was increased by 33% for SWPF based solutions and by 46% for Tank 11 based solutions. The larger amount of heat from mixes containing higher aluminate concentration must be accounted for in the modeling effort which determines the pour schedule for Saltstone. The increased induction periods were shown to be associated with hydration reactions of the blast furnace slag. The rate of heat generation with high aluminate solutions and Portland cement were only accelerated whereas high aluminate mixes containing blast furnace slag only showed the characteristic increase in induction time that was observed with mixes prepared using the premix blend of cementitious materials. It was shown that fly ash does not react significantly during the first seven days of curing but then

Lysimeter study of vegetative uptake from saltstone. Part I. Design, installation, and data collection plan

International Nuclear Information System (INIS)

Johnson, T.L.

1986-02-01

A field test facility has been designed and installed to obtain data on the vegetative uptake of radionuclides from buried low-level radioactive waste. The waste is a cement-like, solidified salt solution known as saltstone. The facility consists of 32 lysimeters (containers 6 feet in diameter and 6 to 10 feet in depth) holding buried saltstone at varying depths, and with varying types of vegetation grown at the surface. Vegetation, soil, and groundwater samples will be analyzed for Tc-99, Sr-90, I-129, Cs-137, and other radionuclides. Groundwater will also be analyzed for other water quality parameters, including nitrates

Saltstone: cement-based waste form for disposal of Savannah River Plant low-level radioactive salt waste

International Nuclear Information System (INIS)

Langton, C.A.

1984-01-01

Defense waste processing at the Savannah River Plant will include decontamination and disposal of approximately 400 million liters of waste containing NaNO 3 , NaOH, Na 2 SO 4 , and NaNO 2 . After decontamination, the salt solution is classified as low-level waste. A cement-based waste form, saltstone, has been designed for disposal of Savannah River Plant low-level radioactive salt waste. Bulk properties of this material have been tailored with respect to salt leach rate, permeability, and compressive strength. Microstructure and mineralogy of leached and unleached specimens were characterized by SEM and x-ray diffraction analyses. The disposal system for the DWPF salt waste includes reconstitution of the crystallized salt as a solution containing 32 wt % solids. This solution will be decontaminated to remove 137 Cs and 90 Sr and then stabilized in a cement-based waste form. Laboratory and field tests indicate that this stabilization process greatly reduces the mobility of all of the waste constitutents in the surface and near-surface environment. Engineered trenches for subsurface burial of the saltstone have been designed to ensure compatibility between the waste form and the environment. The total disposal sytem, saltstone-trench-surrounding soil, has been designed to contain radionuclides, Cr, and Hg by both physical encapsulation and chemical fixation mechanisms. Physical encapsulation of the salts is the mechanism employed for controlling N and OH releases. In this way, final disposal of the SRP low-level waste can be achieved and the quality of the groundwater at the perimeter of the disposal site meets EPA drinking water standards

Adaptation of the TCLP and SW-846 methods to radioactive mixed waste

International Nuclear Information System (INIS)

Griest, W.H.; Schenley, R.L.; Caton, J.E.; Wolfe, P.F.

1994-01-01

Modifications of conventional sample preparation and analytical methods are necessary to provide radiation protection and to meet sensitivity requirements for regulated constituents when working with radioactive samples. Adaptations of regulatory methods for determining ''total'' Toxicity Characteristic Leaching Procedure (TCLP) volatile and semivolatile organics and pesticides, and for conducting aqueous leaching are presented

Performance Properties Of Saltstone Produced Using SWPF Simulants

International Nuclear Information System (INIS)

Harbour, J.; Edwards, T.

2010-01-01

The overwhelming majority of waste to be immobilized at the Saltstone Production Facility will come from the waste stream exiting the Salt Waste Processing Facility (SWPF). These SWPF batches are salt solutions that result from pretreatment of the High Level Waste (HLW) supernate by an Actinide Removal Process followed by Caustic Side Solvent Extraction. The concentration of aluminate within these streams will vary and be determined by (1) the concentration in the incoming salt waste stream, (2) the degree of aluminum leaching from the HLW, (3) the method for introducing the aluminate into the waste stream (continuous or batch) and (4) and any operational or regulatory limitations. The overall Performance Assessment outcome for the Saltstone Disposal Facility will depend significantly on the performance properties of the SWPF Saltstone grouts. This report identifies and quantifies, when possible, those factors that drive the performance properties of the projected SWPF grouts. Previous work has identified aluminate concentration in the salt waste stream as a key factor in determining performance. Consequently, significant variation in the aluminate concentration to a maximum level of 0.65 M was investigated in this report. The SWPF baseline grout is a mix with a 0.60 water to cementitious ratio and a premix composition of 45 wt % slag, 45 wt % fly ash and 10 wt % portland cement. The key factors that drive performance of the SWPF mixes were determined to be (1) the time/temperature profile for curing, (2) water to cementitious materials ratio, (3) aluminate concentration in the waste stream, and (4) wt % slag in the premix. An increase in the curing temperature for mixes with 45 wt % slag resulted in a 2.5 times decrease in Young's modulus. The reduction of Young's modulus measured at 60 C versus 22 C was mitigated by an increase in the aluminate concentration but was still significant. For mixes containing 60 wt % slag, the reduction in Young's modulus between

Waste Incidental to Reprocessing Evaluation for Disposing Saltcake to Saltstone

International Nuclear Information System (INIS)

Jones, R.T.

2002-01-01

This Waste Incidental to Reprocessing Evaluation is performed in accordance with Department of Energy Order 435.1, Radioactive Waste Management. This evaluation is performed in order to determine whether saltcake currently stored in the Tank Farms, when separated from supernate, meets WIR requirements and can therefore be managed as Low Level Waste and disposed in the Saltstone Production and Disposal Facility in Z-Area

Addendum to the composite analysis for the E-Area Vaults and Saltstone Disposal Facilities

Energy Technology Data Exchange (ETDEWEB)

Cook, J.R.

2000-03-13

This report documents the composite analysis performed on the two active SRS low-level radioactive waste disposal facilities. The facilities are the Z-Area Saltstone Disposal Facility and the E-Area Vaults Disposal Facility.

Addendum to the composite analysis for the E-Area Vaults and Saltstone Disposal Facilities

International Nuclear Information System (INIS)

Cook, J.R.

2000-01-01

This report documents the composite analysis performed on the two active SRS low-level radioactive waste disposal facilities. The facilities are the Z-Area Saltstone Disposal Facility and the E-Area Vaults Disposal Facility

PHYSICAL PROPERTY MEASUREMENTS OF LABORATORY PREPARED SALTSTONE GROUT

Energy Technology Data Exchange (ETDEWEB)

Hansen, E.; Cozzi, A.; Edwards, T.

2014-05-05

The Saltstone Production Facility (SPF) built two new Saltstone Disposal Units (SDU), SDU 3 and SDU 5, in 2013. The variable frequency drive (VFD) for the grout transfer hose pump tripped due to high current demand by the motor during the initial radioactive saltstone transfer to SDU 5B on 12/5/2013. This was not observed during clean cap processing on July 5, 2013 to SDU 3A, which is a slightly longer distance from the SPF than is SDU 5B. Saltstone Design Authority (SDA) is evaluating the grout pump performance and capabilities to transfer the grout processed in SPF to SDU 3/5. To assist in this evaluation, grout physical properties are required. At this time, there are no rheological data from the actual SPF so the properties of laboratory prepared samples using simulated salt solution or Tank 50 salt solution will be measured. The physical properties of grout prepared in the laboratory with de-ionized water (DI) and salt solutions were obtained at 0.60 and 0.59 water to premix (W/P) ratios, respectively. The yield stress of the DI grout was greater than any salt grout. The plastic viscosity of the DI grout was lower than all of the salt grouts (including salt grout with admixture). When these physical data were used to determine the pressure drop and fluid horsepower for steady state conditions, the salt grouts without admixture addition required a higher pressure drop and higher fluid horsepower to transport. When 0.00076 g Daratard 17/g premix was added, both the pressure drop and fluid horsepower were below that of the DI grout. Higher concentrations of Daratard 17 further reduced the pressure drop and fluid horsepower. The uncertainty in the single point Bingham Plastic parameters is + 4% of the reported values and is the bounding uncertainty. Two different mechanical agitator mixing protocols were followed for the simulant salt grout, one having a total mixing time of three minutes and the other having a time of 10 minutes. The Bingham Plastic parameters

Special Analysis: Revised 14C Disposal Limits for the Saltstone Disposal Facility

International Nuclear Information System (INIS)

Kaplan, D.I.

2004-01-01

The Saltstone Special Analysis calculated a limit for 14C based on the atmospheric pathway of 52 pCi/mL using some very conservative assumptions. This was compared to the estimated Low Curie Salt concentration of 0.45 pCi/mL and since the limit was two orders of magnitude greater than the estimated concentration, the decision was made that no further analysis was needed. The 14C concentration in Tank 41 has been found to be much greater than the estimated concentration and to exceed the limit derived in the Special Analysis. A rigorous analysis of the release of 14C via the air pathway that considers the chemical effects of the Saltstone system has shown that the flux of 14C is significantly less than that assumed in the Special Analysis. The net result is an inventory limit for 14C that is significantly higher than that derived in the Special Analysis that will also meet the performance objectives of DOE Order 435.1

PORFLOW Simulations Supporting Saltstone Disposal Unit Design Optimization

Energy Technology Data Exchange (ETDEWEB)

Flach, G. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hang, T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Taylor, G. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-12-10

SRNL was requested by SRR to perform PORFLOW simulations to support potential cost-saving design modifications to future Saltstone Disposal Units in Z-Area (SRR-CWDA-2015-00120). The design sensitivity cases are defined in a modeling input specification document SRR-CWDA-2015-00133 Rev. 1. A high-level description of PORFLOW modeling and interpretation of results are provided in SRR-CWDA-2015-00169. The present report focuses on underlying technical issues and details of PORFLOW modeling not addressed by the input specification and results interpretation documents. Design checking of PORFLOW modeling is documented in SRNL-L3200-2015-00146.

SENSITIVITY ANALYSIS FOR SALTSTONE DISPOSAL UNIT COLUMN DEGRADATION ANALYSES

Energy Technology Data Exchange (ETDEWEB)

Flach, G.

2014-10-28

PORFLOW related analyses supporting a Sensitivity Analysis for Saltstone Disposal Unit (SDU) column degradation were performed. Previous analyses, Flach and Taylor 2014, used a model in which the SDU columns degraded in a piecewise manner from the top and bottom simultaneously. The current analyses employs a model in which all pieces of the column degrade at the same time. Information was extracted from the analyses which may be useful in determining the distribution of Tc-99 in the various SDUs throughout time and in determining flow balances for the SDUs.

Comparative Study on the Leaching Characteristics of Industrial Sludge and Fly Ash using KSLP and TCLP Techniques

International Nuclear Information System (INIS)

Lee, B.K.; Hwang, H.W.

2010-01-01

Leaching characteristics of industrial sludge and fly ash using Korean Standard Leaching Procedure (KSLP) and Toxicity Characteristics Leaching Procedure (TCLP) were studied. Possibilities of re-adsorption of heavy metal ions on the surface of sludge and ash during the course of leaching were also investigated. KSLP looked relatively more aggressive than the TCLP in leaching heavy metal ions. Concentrations of metal ions leached in both the methods, however, were found very low in comparison to the concentration of ions present in the original samples. In case of sludge, heavy metal ions showed relatively high rate of leaching at fourth and fifth stages of sequential extraction while ash showed high rate of leaching at the first three stages of extraction. Some of the concentrations of heavy metal ions leached out in the tests also found to be adsorbed on the surface of sludge and ash. Heavy metal ions present in high concentrations in the sample showed lower rate of adsorption than their leaching rate. No distinct difference in the results of KSLP and TCLP was observed. However, variations in the leaching results could be due to the different nature of hazardous waste and leaching conditions. More information like kinetics of leaching, mineralogical characteristics of waste and site characteristics of landfill were required to predict more accurate leaching behavior of ions in natural conditions. (author)

Z-Area Saltstone Disposal Facility Groundwater Monitoring Report. 1997 Annual Report

International Nuclear Information System (INIS)

Roach, J.L. Jr.

1997-12-01

Samples from the ZBG wells at the Z-Area Saltstone Disposal Facility are analyzed for constituents required by South Carolina Department of Health and Environmental Control (SCDHEC) Industrial Solid Waste Permit number-sign 025500-1603 (formerly IWP-217). No constituents were reported above SCDHEC-proposed groundwater monitoring standards or final Primary Drinking Water Standards during first or third quareters 1997. No constituents were detected above SRS flagging criteria during first or third quarters 1997

Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

Energy Technology Data Exchange (ETDEWEB)

Bowers, J.S.; Anson, J.R.; Painter, S.M. [Lawrence Livermore National Lab., CA (United States)] [and others

1995-12-31

Stabilization is a best demonstrated available technology, or BDAT. This technology traps toxic contaminants in a matrix so that they do not leach into the environment. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP the federal leach test) or the Soluble Threshold Leachate Concentration (STLC the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California`s and EPA`s, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. The concentration in the leachate is approximately ten times higher for the STLC procedure than the TCLP. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory (LLNL), additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens) when formulating a stabilization matrix, and they have a neutral pH. By using these clays and additives, LLNL`s highly concentrated wastewater treatment sludges have passed the TCLP and STLC tests. The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements.

[Evaluation of phosphate-containing amendments on remediation effect and influential factors in a lead/zinc mining tailings contaminated soil using TCLP and forms].

Science.gov (United States)

Chen, Jian-Jun; Yu, Tian-Ming; Wang, Bi-Ling; Xie, Zheng-Miao

2010-01-01

A pot experiment was conducted to evaluate the effects of phosphate-containing (P) amendments on the toxicity and bioavailability of Pb and Zn in a soil contaminated by mining tailings using toxicity characteristic leaching procedure (TCLP) and water soluble, exchangeable leaching procedures in order to find out the appropriate P application rates to reduce the soil TCLP extractable Pb to below the USA EPA's regulatory limit levels. The results showed that TCLP extractable Pb concentrations were significantly decreased by up to 93.3% for MPP treatments and up to 68.5% for SSP treatments after P application. The dose required to reduce leachable Pb below the EPA's regulatory limit level was found to be around the molar ratio of v(P/Pb) = 0.6 for MPP and 1.8 for SSP. It was also found both MPP and SSP could reduce the exchangeable Pb and Zn concentrations that all bio-available Zn forms including water soluble, exchangeable, and TCLP extractable forms in soil were significantly and negatively correlated to soil pH values, indicating that the content of Zn in the soil was mostly controlled by soil pH value even after P application. These results suggest that P as MPP and SSP could successfully decrease the toxicity and bioavailability of Pb and Zn in the contaminated soil.

Radiological performance assessment for the Z-Area Saltstone Disposal Facility

Energy Technology Data Exchange (ETDEWEB)

Cook, J.R.; Fowler, J.R. [Westinghouse Savannah River Co., Aiken, SC (United States)

1992-12-18

This radiological performance assessment (RPA) for the Savannah River Site (SRS) Saltstone Disposal Facility (SDF) was prepared in accordance with the requirements of Chapter III of the US Department of Energy Order 5820.2A. The Order specifies that an RPA should provide reasonable assurance that a low-level waste (LLW) disposal facility will comply with the performance objectives of the Order. The performance objectives require that: (1) exposures of the general public to radioactivity in the waste or released from the waste will not result in an effective dose equivalent of 25 mrem per year; (2) releases to the atmosphere will meet the requirements of 40 CFR 61; (3) inadvertent intruders will not be committed to an excess of an effective dose equivalent of 100 mrem per year from chronic exposure, or 500 mrem from a single acute exposure; and (4) groundwater resources will be protected in accordance with Federal, State and local requirements.

Radiological performance assessment for the Z-Area Saltstone Disposal Facility

International Nuclear Information System (INIS)

Cook, J.R.; Fowler, J.R.

1992-01-01

This radiological performance assessment (RPA) for the Savannah River Site (SRS) Saltstone Disposal Facility (SDF) was prepared in accordance with the requirements of Chapter III of the US Department of Energy Order 5820.2A. The Order specifies that an RPA should provide reasonable assurance that a low-level waste (LLW) disposal facility will comply with the performance objectives of the Order. The performance objectives require that: (1) exposures of the general public to radioactivity in the waste or released from the waste will not result in an effective dose equivalent of 25 mrem per year; (2) releases to the atmosphere will meet the requirements of 40 CFR 61; (3) inadvertent intruders will not be committed to an excess of an effective dose equivalent of 100 mrem per year from chronic exposure, or 500 mrem from a single acute exposure; and (4) groundwater resources will be protected in accordance with Federal, State and local requirements

Delisting petition for 300-M saltstone (treated F006 sludge) from the 300-M liquid effluent treatment facility

Energy Technology Data Exchange (ETDEWEB)

1989-04-04

This petition seeks exclusion for stabilized and solidified sludge material generated by treatment of wastewater from the 300-M aluminum forming and metal finishing processes. The waste contains both hazardous and radioactive components and is classified as a mixed waste. The objective of this petition is to demonstrate that the stabilized sludge material (saltstone), when properly disposed, will not exceed the health-based standards for the hazardous constituents. This petition contains sampling and analytical data which justify the request for exclusion. The results show that when the data are applied to the EPA Vertical and Horizontal Spread (VHS) Model, health-based standards for all hazardous waste constituents will not be exceeded during worst case operating and environmental conditions. Disposal of the stabilized sludge material in concrete vaults will meet the requirements pertaining to Waste Management Activities for Groundwater Protection at the Savannah River Site in Aiken, S.C. Documents set forth performance objectives and disposal options for low-level radioactive waste disposal. Concrete vaults specified for disposal of 300-M saltstone (treated F006 sludge) assure that these performance objectives will be met.

Groundwater Monitoring Plan for the Z-Area Saltstone Facility

International Nuclear Information System (INIS)

Wells, D.

2002-01-01

Groundwater monitoring has been conducted at the Z-Area Saltstone Disposal Facility since 1987. At that time, groundwater monitoring was not required by the industrial landfill regulations, but a modest monitoring program was required by the operating permit. In 1996 SRS proposed a program based on direct push sampling. This program called for biennial direct push sampling within 25 feet of each waste-containing cell with additional samples being taken in areas where excessive cracking had been observed. The direct push proposal was accepted by The South Carolina Department of Health and Environmental Control (SCDHEC). The Industrial Solid Waste Landfill Regulations were revised in 1998 and now include requirements for groundwater monitoring. The major elements of those regulations and their application at Z-Area are discussed. These are a point of compliance, groundwater protection standards, the groundwater monitoring system, sampling and analysis, and data evaluation and reporting

Large-scale demonstration of disposal of decontaminated salt as saltstone. Part I. Construction, loading, and capping of lysimeters

International Nuclear Information System (INIS)

Wolf, H.C.

1984-06-01

The installation phase of a large-scale demonstration of the disposal concept for decontaminated, low-level radioactive salt waste at the Savannah River Plant was completed in December 1983 and January 1984. The installation entailed immobilizing 7500 gallons of decontaminated salt solution with a blended cement formulation and pouring the resulting grout, saltstone, into three specially designed lysimeters for extended in-field leaching tests under natural conditions. 4 references, 35 figures, 4 tables

Miscibility Evaluation Of The Next Generation Solvent With Polymers Currently Used At DWPF, MCU, And Saltstone

Energy Technology Data Exchange (ETDEWEB)

Fondeur, F. F.

2013-04-17

The Office of Waste Processing, within the Office of Technology Innovation and Development, funded the development of an enhanced Caustic-Side Solvent Extraction (CSSX) solvent for deployment at the Savannah River Site for removal of cesium from High Level Waste. This effort lead to the development of the Next Generation Solvent (NGS) with Tris (3,7-dimethyl octyl) guanidine (TiDG). The first deployment target for the NGS solvent is within the Modular CSSX Unit (MCU). Deployment of a new chemical within an existing facility requires verification that the new chemical components are compatible with the installed equipment. In the instance of a new organic solvent, the primary focus is on compatibility of the solvent with organic polymers used in the affected facility. This report provides the calculated data from exposing these polymers to the Next Generation Solvent. An assessment of the dimensional stability of polymers known to be used or present in the MCU, Defense Waste Processing Facility (DWPF), and Saltstone facilities that will be exposed to the NGS showed that TiDG could selectively affect the elastomers and some thermoplastics to varying extents, but the typical use of these polymers in a confined geometry will likely prevent the NGS from impacting component performance. The polymers identified as of primary concern include Grafoil® (flexible graphite), Tefzel®, Isolast®, ethylene-propylene-diene monomer (EPDM) rubber, nitrile-butadiene rubber (NBR), styrene-butadiene rubber (SBR), ultra high molecular weight polyethylene (UHMWPE), and fluorocarbon rubber (FKM). Certain polymers like NBR and EPDM were found to interact mildly with NGS but their calculated swelling and the confined geometry will impede interaction with NGS. In addition, it was found that Vellumoid (cellulose fibers-reinforced glycerin and protein) may leach protein and Polyvinyl Chloride (PVC) may leach plasticizer (such as Bis-Ethylhexyl-Phthalates) into the NGS solvent. Either case

Electrical conductivity of cobalt doped La 0.8Sr 0.2Ga 0.8Mg 0.2O 3- δ

Science.gov (United States)

Wang, Shizhong; Wu, Lingli; Liang, Ying

La 0.8Sr 0.2Ga 0.8Mg 0.2O 3- δ (LSGM8282), La 0.8Sr 0.2Ga 0.8Mg 0.15Co 0.05O 3- δ (LSGMC5) and La 0.8Sr 0.2Ga 0.8Mg 0.115Co 0.085O 3- δ (LSGMC8.5) were prepared using a conventional solid-state reaction. Electrical conductivities and electronic conductivities of the samples were measured using four-probe impedance spectrometry, four-probe dc polarization and Hebb-Wagner polarization within the temperature range of 973-1173 K. The electrical conductivities in LSGMC5 and LSGMC8.5 increased with decreasing oxygen partial pressures especially in the high (>10 -5 atm) and low oxygen partial pressure regions (lanthanum gallate samples increased with increasing concentration of cobalt, suggesting that the concentration of cobalt should be optimized carefully to maintain a high electrical conductivity and close to 1 oxygen ion transference number.

Data Package for Secondary Waste Form Down-Selection-Cast Stone

International Nuclear Information System (INIS)

Serne, R. Jeffrey; Westsik, Joseph H.

2011-01-01

Available literature on Cast Stone and Saltstone was reviewed with an emphasis on determining how Cast Stone and related grout waste forms performed in relationship to various criteria that will be used to decide whether a specific type of waste form meets acceptance criteria for disposal in the Integrated Disposal Facility (IDF) at Hanford. After the critical review of the Cast Stone/Saltstone literature, we conclude that Cast Stone is a good candidate waste form for further consideration. Cast stone meets the target IDF acceptance criteria for compressive strength, no free liquids, TCLP leachate are below the UTS permissible concentrations and leach rates for Na and Tc-99 are suiteably low. The cost of starting ingredients and equipment necessary to generate Cast Stone waste forms with secondary waste streams are low and the Cast Stone dry blend formulation can be tailored to accommodate variations in liquid waste stream compositions. The database for Cast Stone short-term performance is quite extensive compared to the other three candidate waste solidification processes. The solidification of liquid wastes in Cast Stone is a mature process in comparison to the other three candidates. Successful production of Cast Stone or Saltstone has been demonstrated from lab-scale monoliths with volumes of cm3 through m3 sized blocks to 210-liter sized drums all the way to the large pours into vaults at Savannah River. To date over 9 million gallons of low activity liquid waste has been solidified and disposed in concrete vaults at Savannah River.

Data Package for Secondary Waste Form Down-Selection—Cast Stone

Energy Technology Data Exchange (ETDEWEB)

Serne, R. Jeffrey; Westsik, Joseph H.

2011-09-05

Available literature on Cast Stone and Saltstone was reviewed with an emphasis on determining how Cast Stone and related grout waste forms performed in relationship to various criteria that will be used to decide whether a specific type of waste form meets acceptance criteria for disposal in the Integrated Disposal Facility (IDF) at Hanford. After the critical review of the Cast Stone/Saltstone literature, we conclude that Cast Stone is a good candidate waste form for further consideration. Cast stone meets the target IDF acceptance criteria for compressive strength, no free liquids, TCLP leachate are below the UTS permissible concentrations and leach rates for Na and Tc-99 are suiteably low. The cost of starting ingredients and equipment necessary to generate Cast Stone waste forms with secondary waste streams are low and the Cast Stone dry blend formulation can be tailored to accommodate variations in liquid waste stream compositions. The database for Cast Stone short-term performance is quite extensive compared to the other three candidate waste solidification processes. The solidification of liquid wastes in Cast Stone is a mature process in comparison to the other three candidates. Successful production of Cast Stone or Saltstone has been demonstrated from lab-scale monoliths with volumes of cm3 through m3 sized blocks to 210-liter sized drums all the way to the large pours into vaults at Savannah River. To date over 9 million gallons of low activity liquid waste has been solidified and disposed in concrete vaults at Savannah River.

A non-toxic fluorogenic dye for mitochondria labeling.

Science.gov (United States)

Han, Junyan; Han, Myung Shin; Tung, Ching-Hsuan

2013-11-01

Mitochondria, powerhouses of cells, are responsible for many critical cellular functions, such as cell energy metabolism, reactive oxygen species production, and apoptosis regulation. Monitoring mitochondria morphology in live cells temporally and spatially could help with the understanding of the mechanisms of mitochondrial functional regulation and the pathogenesis of mitochondria-related diseases. A novel non-cytotoxic fluorogenic compound, AcQCy7, was developed as a mitochondria-specific dye. AcQCy7 emitted no fluorescent signal outside of cells, but it became fluorescent after intracellular hydrolysis of the acetyl group. The hydrolyzed fluorescent product was well retained in mitochondria, enabling long-lasting fluorescence imaging of mitochondria without cell washing. A 2-day culture study using AcQCy7 showed no sign of cytotoxicity, whereas a commonly used mitochondria-staining probe, Mitochondria Tracker Green, caused significant cell death even at a much lower concentration. Apoptosis-causing mitochondria fission was monitored clearly in real time by AcQCy7. A simple add-and-read mitochondria specific dye AcQCy7 has been validated in various cell models. Bright mitochondria specific fluorescent signal in treated cells lasted several days without noticeable toxicity. The probe AcQCy7 has been proofed to be a non-toxic agent for long-term mitochondria imaging. © 2013.

Crystal structure and optical property of complex perovskite oxynitrides ALi0.2Nb0.8O2.8N0.2, ANa0.2Nb0.8O2.8N0.2, and AMg0.2Nb0.8O2.6N0.4 (A = Sr, Ba)

Science.gov (United States)

Moon, Keon Ho; Avdeev, Maxim; Kim, Young-Il

2017-10-01

Oxynitride type complex perovskites AM0.2Nb0.8O3-xNx (A = Sr, Ba; M = Li, Na, Mg) were newly synthesized by the solid state diffusion of Li+, Na+, or Mg2+ into the layered oxide, A5Nb4O15, with concurrent O/N substitution. Neutron and synchrotron X-ray Rietveld refinement showed that SrLi0.2Nb0.8O2.8N0.2, SrNa0.2Nb0.8O2.8N0.2, and SrMg0.2Nb0.8O2.6N0.4 had body-centered tetragonal symmetry (I4/mcm), while those with A = Ba had simple cubic symmetry (Pm 3 ̅ m). In the tetragonal Sr-compounds, the nitrogen atoms were localized on the c-axial 4a site. However, the octahedral cations, M/Nb (M = Li, Na, Mg) were distributed randomly in all six compounds. The lattice volume of AM0.2Nb0.8O3-xNx was dependent on various factors including the type of A and the electronegativity of M. Compared to the simple perovskites, ANbO2N (A = Sr, Ba), AM0.2Nb0.8O3-xNx had wider band gaps (1.76-2.15 eV for A = Sr and 1.65-2.10 eV for A = Ba), but significantly lower sub-gap absorption.

Stabilization of inorganic mixed waste to pass the TCLP and STLC tests using clay and pH-insensitive additives

International Nuclear Information System (INIS)

Bowers, J.S.; Anson, J.R.; Painter, S.M.; Maitino, R.E.

1995-03-01

Stabilization traps toxic contaminants (usually both chemically and physically) in a matrix so that they do not leach into the environment. Typical contaminants are metals (mostly transition metals) that exhibit the characteristic of toxicity. The stabilization process routinely uses pozzolanic materials. Portland cement, fly ash-lime mixes, gypsum cements, and clays are some of the most common materials. In many instances, materials that can pass the Toxicity Characteristic Leaching Procedure (TCLP-the federal leach test) or the Soluble Threshold Leachate Concentration (STLC-the California leach test) must have high concentrations of lime or other caustic material because of the low pH of the leaching media. Both leaching media, California's and EPA's, have a pH of 5.0. California uses citric acid and sodium citrate while EPA uses acetic acid and sodium acetate. These media can form ligands that provide excellent metal leaching. Because of the aggressive nature of the leaching medium, stabilized wastes in many cases will not pass the leaching tests. At the Lawrence Livermore National Laboratory, additives such as dithiocarbamates and thiocarbonates, which are pH-insensitive and provide resistance to ligand formation, are used in the waste stabilization process. Attapulgite, montmorillonite, and sepiolite clays are used because they are forgiving (recipe can be adjusted before the matrix hardens). The most frequently used stabilization process consists of a customized recipe involving waste sludge, clay and dithiocarbamate salt, mixed with a double planetary mixer into a pasty consistency. TCLP and STLC data on this waste matrix have shown that the process matrix meets land disposal requirements

A theoretical study of the complexes of N2O with H+, Li+, and HF using various correlation methods

International Nuclear Information System (INIS)

Del Bene, J.E.; Stahlberg, E.A.; Shavitt, I.

1990-01-01

Binding energies for complexes of N 2 O with the acids H + , Li + , and HF have been computed using the following correlation methods: many-body (Moller-Plesset) perturbation theory at second (MP2), third (MP3), and fourth (MP4) order; the quadratic CI method with single and double excitations (QCISD) and with noniterative inclusion of triple excitations (QCISD(T)); the linearized coupled-cluster method (LCCM); the averaged coupled-pair functional (ACPF); configuration interaction with all single and double excitations (CISD); and CISD with the Davidson and Pople corrections. The convergence of the Moller-Plesset expansion is erratic, predicting that the terminal nitrogen is the preferred binding site for the complexes at the MP2 and MP4 levels, in disagreement with Hartree-Fock and MP3 and all other models (including the infinite-order QCI). The effect of triple excitations at MP4 and QCI is to destabilize complexes bound at O and stabilize those bound at N, but this effect is greatly overestimated at MP4 relative to QCI. Except for the LCCM result for N-protonated N 2 O, ACPF and LCCM binding energies are similar to the QCISD values. The size-consistency error in the ACPF binding energies of the complexes of N 2 O with HF is about 0.5 kcal/mol. The CISD size-consistency error for these complexes is 23 kcal/mol, leading to negative binding energies when computed relative to isolated N 2 O and HF

NUMERICAL FLOW AND TRANSPORT SIMULATIONS SUPPORTING THE SALTSTONE FACILITY PERFORMANCE ASSESSMENT

Energy Technology Data Exchange (ETDEWEB)

Flach, G.

2009-02-28

The Saltstone Disposal Facility Performance Assessment (PA) is being revised to incorporate requirements of Section 3116 of the Ronald W. Reagan National Defense Authorization Act for Fiscal Year 2005 (NDAA), and updated data and understanding of vault performance since the 1992 PA (Cook and Fowler 1992) and related Special Analyses. A hybrid approach was chosen for modeling contaminant transport from vaults and future disposal cells to exposure points. A higher resolution, largely deterministic, analysis is performed on a best-estimate Base Case scenario using the PORFLOW numerical analysis code. a few additional sensitivity cases are simulated to examine alternative scenarios and parameter settings. Stochastic analysis is performed on a simpler representation of the SDF system using the GoldSim code to estimate uncertainty and sensitivity about the Base Case. This report describes development of PORFLOW models supporting the SDF PA, and presents sample results to illustrate model behaviors and define impacts relative to key facility performance objectives. The SDF PA document, when issued, should be consulted for a comprehensive presentation of results.

Addendum to the Composite Analysis for the E-Area Vaults and Saltstone Disposal Facilities

International Nuclear Information System (INIS)

Cook, J.R.

2002-01-01

Revision 1 of the Composite Analysis (CA) Addendum has been prepared to respond to the U.S. Department of Energy (DOE) Low-Level Waste Disposal Facilities Federal Review Group review of the CA. This addendum to the composite analysis responds to the conditions of approval. The composite analysis was performed on the two active SRS low-level radioactive waste disposal facilities. The facilities are the Z-Area Saltstone Disposal Facility and the E-Area Vaults Disposal Facility. The analysis calculated potential releases to the environment from all sources of residual radioactive material expected to remain in the General Separations Area (GSA). The GSA is the central part of the Savannah River Site and contains all of the waste disposal facilities, the chemical separation facilities and associated high-level waste storage facilities, as well as numerous other sources of radioactive material

Evaluation of Mobility, Bioavailability and Toxicity of Pb and Cd in Contaminated Soil Using TCLP, BCR and Earthworms

Science.gov (United States)

Kede, Maria Luiza F. M.; Correia, Fabio V.; Conceição, Paulo F.; Salles Junior, Sidney F.; Marques, Marcia; Moreira, Josino C.; Pérez, Daniel V.

2014-01-01

The objective of the present study was to investigate the reduction of mobility, availability and toxicity found in soil contaminated with lead (Pb) and cadmium (Cd) from Santo Amaro Municipality, Bahia, Brazil using two combined methods, commonly tested separately according to the literature: metal mobilization with phosphates and phytoextraction. The strategy applied was the treatment with two sources of phosphates (separately and mixed) followed by phytoremediation with vetiver grass (Vetiveria zizanioides (L.)). The treatments applied (in triplicates) were: T1—potassium dihydrogen phosphate (KH2PO4); T2—reactive natural phosphate fertilizer (NRP) and; T3—a mixture 1:1 of KH2PO4 and NRP. After this step, untreated and treated soils were planted with vetiver grass. The extraction procedures and assays applied to contaminated soil before and after the treatments included metal mobility test (TCLP); sequential extraction with BCR method; toxicity assays with Eisenia andrei. The soil-to-plant transfer factors (TF) for Pb and Cd were estimated in all cases. All treatments with phosphates followed by phytoremediation reduced the mobility and availability of Pb and Cd, being KH2PO4 (T1) plus phytoremediation the most effective one. Soil toxicity however, remained high after all treatments. PMID:25386955

Evaluation of Mobility, Bioavailability and Toxicity of Pb and Cd in Contaminated Soil Using TCLP, BCR and Earthworms

Directory of Open Access Journals (Sweden)

Maria Luiza F. M. Kede

2014-11-01

Full Text Available The objective of the present study was to investigate the reduction of mobility, availability and toxicity found in soil contaminated with lead (Pb and cadmium (Cd from Santo Amaro Municipality, Bahia, Brazil using two combined methods, commonly tested separately according to the literature: metal mobilization with phosphates and phytoextraction. The strategy applied was the treatment with two sources of phosphates (separately and mixed followed by phytoremediation with vetiver grass (Vetiveria zizanioides (L.. The treatments applied (in triplicates were: T1—potassium dihydrogen phosphate (KH2PO4; T2—reactive natural phosphate fertilizer (NRP and; T3—a mixture 1:1 of KH2PO4 and NRP. After this step, untreated and treated soils were planted with vetiver grass. The extraction procedures and assays applied to contaminated soil before and after the treatments included metal mobility test (TCLP; sequential extraction with BCR method; toxicity assays with Eisenia andrei. The soil-to-plant transfer factors (TF for Pb and Cd were estimated in all cases. All treatments with phosphates followed by phytoremediation reduced the mobility and availability of Pb and Cd, being KH2PO4 (T1 plus phytoremediation the most effective one. Soil toxicity however, remained high after all treatments.

Oxygen Non-Stoichiometry and Electrical Conductivity of LA0.2Sr0.8Fe0.8B0.2O3-d, B = Fe, Ti, Ta

NARCIS (Netherlands)

Lohne, O.F.; Phung, T.N.; Grande, T.; Bouwmeester, Henricus J.M.; Hendriksen, P.V.; Sogaard, M.; Wiik, K.

2014-01-01

The oxygen non-stoichiometry was determined by coulometric titration for the perovskite oxides La0.2Sr0.8FeO3−δ and La0.2Sr0.8Fe0.8B0.2O3−δ (B = Ti4+ and Ta5+) in the temperature range 600 ◦C ≤ T ≤ 900 ◦C and the oxygen partial pressure range: 1 · 10−15 ≤ pO2 ≤ 0.209 atm. The non-stoichiometry (δ)

THERMAL EXPANSION BEHAVIOR OF THE Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF WITH Sm0.2Ce0.8O1.9

Directory of Open Access Journals (Sweden)

M. AHMADREZAEI

2014-03-01

Full Text Available Nanostructured perovskite oxides of Ba0.2Sr0.8Co0.8Fe0.2O3−δ (BSCF were synthesized through the co-precipitation method. The thermal decomposition, phase formation and thermal expansion behavior of BSCF were characterized by thermogravimetric analysis, X-ray diffraction (XRD, and dilatometry, respectively. XRD peaks were indexed to a cubic perovskite structure with a Pm3m (221 space group. All the combined oxides produced the desired perovskite-phase BSCF. The microstructures were characterized by scanning electron microscopy (SEM and transmission electron microscopy (TEM. The TEM analysis showed that BSCF powders had uniform nanoparticle sizes and high homogeneity. The cross-sectional SEM micrograph of BSCF exhibited a continuous and no delaminated layer from the electrolyte-supported cell. The thermal expansion coefficient (TEC of BSCF was 16.2×10-6 K-1 at a temperature range of 600°C to 800°C. Additional experiments showed that the TEC of BSCF is comparable to that of Sm0.2Ce0.8O1.9 (SDC within the same temperature range. The results demonstrate that BSFC is a promising cathode material for intermediate-temperature solid-oxide fuel cells.

Energy Auditor and Quality Control Inspector Competency Model

Energy Technology Data Exchange (ETDEWEB)

Head, Heather R [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Kurnik, Charles W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schroeder, Derek [U.S. Department of Energy; Cutchin, Kelly [Simonson Management Services

2018-05-02

The Energy Auditor (EA) and Quality Control Inspector (QCI) Competency model was developed to identify the soft skills, foundational competencies and define the levels of Knowledge, Skills, and Abilities (KSAs) required to successfully perform the tasks defined in the EA and QCI Job Task Analysis (JTAs), the U.S. Department of Energy (DOE) used the U.S. Department of Labor's (DOL) Competency Model Clearinghouse resources to develop a QCI and EA Competency Model. To keep the QCI and EA competency model consistent with other construction and energy management competency models, DOE and the National Renewable Energy Laboratory used the existing 'Residential Construction Competency Model' and the 'Advanced Commercial Building Competency Model' where appropriate.

QCI Common

Energy Technology Data Exchange (ETDEWEB)

2016-11-18

There are many common software patterns and utilities for the ORNL Quantum Computing Institute that can and should be shared across projects. Otherwise we find duplication of code which adds unwanted complexity. This is a software product seeks to alleviate this by providing common utilities such as object factories, graph data structures, parameter input mechanisms, etc., for other software products within the ORNL Quantum Computing Institute. This work enables pure basic research, has no export controlled utilities, and has no real commercial value.

(La, Pr)0.8Sr0.2FeO3-δ-Sm 0.2Ce0.8O2-δ composite cathode for proton-conducting solid oxide fuel cells

KAUST Repository

Chen, Yonghong

2014-08-01

Mixed rare-earth (La, Pr)0.8Sr0.2FeO 3-δ-Sm0.2Ce0.8O2-δ (LPSF-SDC) composite cathode was investigated for proton-conducting solid oxide fuel cells based on protonic BaZr0.1Ce0.7Y 0.2O3-δ (BZCY) electrolyte. The powders of La 0.8-xPrxSr0.2FeO3-δ (x = 0, 0.2, 0.4, 0.6), Sm0.2Ce0.8O2-δ (SDC) and BaZr0.1Ce0.7Y0.2O3-δ (BZCY) were synthesized by a citric acid-nitrates self-propagating combustion method. The XRD results indicate that La0.8-xPrxSr 0.2FeO3-δ samples calcined at 950 °C exhibit perovskite structure and there are no interactions between LPSF0.2 and SDC at 1100 °C. The average thermal expansion coefficient (TEC) of LPSF0.2-SDC, BZCY and NiO-BZCY is 12.50 × 10-6 K-1, 13.51 × 10-6 K-1 and 13.47 × 10-6 K -1, respectively, which can provide good thermal compatibility between electrodes and electrolyte. An anode-supported single cell of NiO-BZCY|BZCY|LPSF0.2-SDC was successfully fabricated and operated from 700 °C to 550 °C with humidified hydrogen (∼3% H2O) as fuel and the static air as oxidant. A high maximum power density of 488 mW cm -2, an open-circuit potential of 0.95 V, and a low electrode polarization resistance of 0.071 Ω cm2 were achieved at 700 °C. Preliminary results demonstrate that LPSF0.2-SDC composite is a promising cathode material for proton-conducting solid oxide fuel cells. © 2014, Hydrogen Energy Publications, LLC. Published by Elsevier Ltd. All rights reserved.

Electrical conductivity of cobalt doped La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.2}O{sub 3-{delta}}

Energy Technology Data Exchange (ETDEWEB)

Wang, Shizhong; Wu, Lingli; Liang, Ying [Department of Chemistry, Xiamen University, Xiamen 361005, Fujian (China)

2007-03-30

La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.2}O{sub 3-{delta}} (LSGM8282), La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.15}Co{sub 0.05}O{sub 3-{delta}} (LSGMC5) and La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.115}Co{sub 0.085}O{sub 3-{delta}} (LSGMC8.5) were prepared using a conventional solid-state reaction. Electrical conductivities and electronic conductivities of the samples were measured using four-probe impedance spectrometry, four-probe dc polarization and Hebb-Wagner polarization within the temperature range of 973-1173 K. The electrical conductivities in LSGMC5 and LSGMC8.5 increased with decreasing oxygen partial pressures especially in the high (>10{sup -5} atm) and low oxygen partial pressure regions (<10{sup -15} atm). However, the electrical conductivity in LSGM8282 had no dependency on the oxygen partial pressure. At temperatures higher than 1073 K, P{sub O{sub 2}} dependencies of the free electron conductivities in LSGM8282, LSGMC5 and LSGMC8.5 were about -1/4, and P{sub O{sub 2}} dependencies of the electron hole conductivities were about 0.25, 0.12 and 0.07, respectively. Oxygen ion conductivities in LSGMC5 and LSGMC8.5 increased with decreasing oxygen partial pressures especially in the high and low oxygen partial pressure regions, which was due to the increase in the concentration of oxygen vacancies. The change in the concentration of oxygen vacancies and the valence of cobalt with oxygen partial pressure were determined using a thermo-gravimetric technique. Both the electronic conductivity and oxygen ion conductivity in cobalt doped lanthanum gallate samples increased with increasing concentration of cobalt, suggesting that the concentration of cobalt should be optimized carefully to maintain a high electrical conductivity and close to 1 oxygen ion transference number. (author)

AcEST: DK950587 [AcEST

Lifescience Database Archive (English)

Full Text Available e uncharacterized protein OS=Oryza... 35 0.050 tr|Q68LQ2|Q68LQ2_9ROSI Maturase (Fragment) OS=Sapria himalaya...na ... 37 0.50 tr|Q5QCI0|Q5QCI0_9ROSI Maturase (Fragment) OS=Sapria himalayana ... 37 0.50 tr|Q6FQH7|Q6FQH7_...C Sbjct: 115 LSRTCGDVDFLLVMGDESDATRELC 139 >tr|Q68LQ2|Q68LQ2_9ROSI Maturase (Fragment) OS=Sapria himalayana ...ase (Fragment) OS=Sapria himalayana GN=matR PE=4 SV=1 Length = 584 Score = 37.4 b

Characteristics of LiMO2 (M = Co, Ni, Ni0.2Co0.8, Ni0.8Co0.2) powders prepared from solution of their acetates

International Nuclear Information System (INIS)

Arof, A.K.

2008-01-01

Stoichiometric quantities of the acetates of lithium, cobalt and nickel were dissolved in distilled water and stirred with a magnetic stirrer. After complete dissolution was obtained, the solutions were heated at 120 deg. C under continuous stirring until some dark colored powder materials were formed. These precursor materials were divided into three batches and heated at 250 deg. C (for 24 h), 370 deg. C (for 24 h) and 800 deg. C for 10 h. The precursor and calcined samples were X-rayed. The X-ray diffractograms for the prepared samples were compared to that of commercialized samples and those published in the literature. The Bragg peak with Miller indices (0 0 3) in the diffractogram of the LiNi 0.8 Co 0.2 O 2 prepared sample showed a lower intensity compared to the (1 0 4) peak. The ratio of the (0 0 3) to (1 0 4) peaks for the LiNi 0.2 Co 0.8 O 2 sample is 1.56. Lattice parameters showed that the LiCoO 2 and LiNi 0.2 Co 0.8 O 2 samples produced by the method in the present investigation have potential to exhibit good electrochemical performance when used as electrodes in lithium ion batteries

A review on economic emission dispatch problems using quantum computational intelligence

Science.gov (United States)

Mahdi, Fahad Parvez; Vasant, Pandian; Kallimani, Vish; Abdullah-Al-Wadud, M.

2016-11-01

Economic emission dispatch (EED) problems are one of the most crucial problems in power systems. Growing energy demand, limitation of natural resources and global warming make this topic into the center of discussion and research. This paper reviews the use of Quantum Computational Intelligence (QCI) in solving Economic Emission Dispatch problems. QCI techniques like Quantum Genetic Algorithm (QGA) and Quantum Particle Swarm Optimization (QPSO) algorithm are discussed here. This paper will encourage the researcher to use more QCI based algorithm to get better optimal result for solving EED problems.

Hydrogen separation through tailored dual phase membranes with nominal composition BaCe0.8Eu0.2O3-δ:Ce0.8Y0.2O2-δ at intermediate temperatures

Science.gov (United States)

Ivanova, Mariya E.; Escolástico, Sonia; Balaguer, Maria; Palisaitis, Justinas; Sohn, Yoo Jung; Meulenberg, Wilhelm A.; Guillon, Olivier; Mayer, Joachim; Serra, Jose M.

2016-11-01

Hydrogen permeation membranes are a key element in improving the energy conversion efficiency and decreasing the greenhouse gas emissions from energy generation. The scientific community faces the challenge of identifying and optimizing stable and effective ceramic materials for H2 separation membranes at elevated temperature (400-800 °C) for industrial separations and intensified catalytic reactors. As such, composite materials with nominal composition BaCe0.8Eu0.2O3-δ:Ce0.8Y0.2O2-δ revealed unprecedented H2 permeation levels of 0.4 to 0.61 mL·min-1·cm-2 at 700 °C measured on 500 μm-thick-specimen. A detailed structural and phase study revealed single phase perovskite and fluorite starting materials synthesized via the conventional ceramic route. Strong tendency of Eu to migrate from the perovskite to the fluorite phase was observed at sintering temperature, leading to significant Eu depletion of the proton conducing BaCe0.8Eu0.2O3-δ phase. Composite microstructure was examined prior and after a variety of functional tests, including electrical conductivity, H2-permeation and stability in CO2 containing atmospheres at elevated temperatures, revealing stable material without morphological and structural changes, with segregation-free interfaces and no further diffusive effects between the constituting phases. In this context, dual phase material based on BaCe0.8Eu0.2O3-δ:Ce0.8Y0.2O2-δ represents a very promising candidate for H2 separating membrane in energy- and environmentally-related applications.

Louisiana SIP: LAC 33:III Ch. 7 - Table 2 - Ambient Air--Methods of Contaminant Measurements; SIP effective 1989-05-08 (LAc49) and 1989-08-14 (LAc50) to 2011-08-03 (LAd34 - Moved to Section 711 and revised [adds PM-2.5])

Science.gov (United States)

Louisiana SIP: LAC 33:III Ch. 7 - Table 2 - Ambient Air--Methods of Contaminant Measurements; SIP effective 1989-05-08 (LAc49) and 1989-08-14 (LAc50) to 2011-08-03 (LAd34 - Moved to Section 711 and revised [adds PM-2.5])

La0.8Sr0.2Co0.8Ni0.2O3-δ impregnated oxygen electrode for H2O/CO2 co-electrolysis in solid oxide electrolysis cells

Science.gov (United States)

Zheng, Haoyu; Tian, Yunfeng; Zhang, Lingling; Chi, Bo; Pu, Jian; Jian, Li

2018-04-01

High-temperature H2O/CO2 co-electrolysis through reversible solid oxide electrolysis cell (SOEC) provides potentially a feasible and eco-friendly way to convert electrical energy into chemicals stored in syngas. In this work, La0.8Sr0.2Co0.8Ni0.2O3-δ (LSCN) impregnated Gd0.1Ce0.9O1.95 (GDC)-(La0.8Sr0.2)0.95MnO3-δ (LSM) composite oxygen electrode is studied as high-performance electrode for H2O/CO2 co-electrolysis. The LSCN impregnated cell exhibits competitive performance with the peak power density of 1057 mW cm-2 at 800 °C in solid oxide fuel cell (SOFC) mode; in co-electrolysis mode, the current density can reach 1.60 A cm-2 at 1.5 V at 800 °C with H2O/CO2 ratio of 2/1. With LSCN nanoparticles dispersed on the surface of GDC-LSM to maximize the reaction active sites, the LSCN impregnated cell shows significant enhanced electrochemical performance at both SOEC and SOFC modes. The influence of feed gas composition (H2O-H2-CO2) and operating voltages on the performance of co-electrolysis are discussed in detail. The cell shows a very stable performance without obvious degradation for more than 100 h. Post-test characterization is analyzed in detail by multiple measurements.

Oxygen Non-Stoichiometry and Electrical Conductivity of La0.2Sr0.8Fe0.8B0.2O3 − δ, B = Fe, Ti, Ta

DEFF Research Database (Denmark)

Lohne, Ørjan Fossmark; Phung, Tan Nhut; Grande, Tor

2014-01-01

The oxygen non-stoichiometry was determined by coulometric titration for the perovskite oxides La0.2Sr0.8FeO3 − δ and La0.2Sr0.8Fe0.8B0.2O3 − δ (B = Ti4+ and Ta5+) in the temperature range 600 °C ⩽ T ⩽ 900 °C and the oxygen partial pressure range: 1⋅10-15≤po2≤0.209 atm. The non-stoichiometry (δ...... for the substituted materials. The electrical conductivity was measured at T = 900 °C in the oxygen partial pressure range: 1⋅10-17≤po2≤0.209 atm. The electrical conductivity and charge carrier mobility decrease upon 20% substitution of Fe roughly by a factor of 2, but do not show a significant dependence......) is observed to decrease with B-site substitution of Fe. The data can be well fitted with simple defect chemistry models. At low oxygen non-stoichiometry all compositions show a deviation from a localized electrons defect model. The standard and partial molar thermodynamic quantities were obtained...

Saltstone SDU6 Modeling Study

International Nuclear Information System (INIS)

Lee, Si Y.; Hyun, Sinjae

2013-01-01

A new disposal unit, designated as Saltstone Disposal Unit 6 (SDU6), is being designed for support of site accelerated closure goals and salt waste projections identified in the new Liquid Waste System Plan. The unit is a cylindrical disposal cell of 375 ft in diameter and 43 ft in height, and it has a minimum 30 million gallons of capacity. SRNL was requested to evaluate the impact of an increased grout placement height on the flow patterns radially spread on the floor and to determine whether grout quality is impacted by the height. The primary goals of the work are to develop the baseline Computational Fluid Dynamics (CFD) model and to perform the evaluations for the flow patterns of grout material in SDU6 as a function of elevation of grout discharge port and grout rheology. Two transient grout models have been developed by taking a three-dimensional multiphase CFD approach to estimate the domain size of the grout materials radially spread on the facility floor and to perform the sensitivity analysis with respect to the baseline design and operating conditions such as elevation height of the discharge port and fresh grout properties. For the CFD modeling calculations, air-grout Volume of Fluid (VOF) method combined with Bingham plastic and time-dependent grout models were used for examining the impact of fluid spread performance for the initial baseline configurations and to evaluate the impact of grout pouring height on grout quality. The grout quality was estimated in terms of the air volume fraction for the grout layer formed on the SDU6 floor, resulting in the change of grout density. The study results should be considered as preliminary scoping analyses since benchmarking analysis is not included in this task scope. Transient analyses with the Bingham plastic model were performed with the FLUENTTM code on the high performance parallel computing platform in SRNL. The analysis coupled with a transient grout aging model was performed by using ANSYS-CFX code

Alternate paddle configuration for improved wear resistance in the saltstone mixer

Energy Technology Data Exchange (ETDEWEB)

Reigel, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fowley, M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2013-09-23

The Saltstone Production Facility has a 10-inch Readco-Kurimoto continuous mixer that mixes the premix dry feeds and low-level waste salt solution to make fresh (uncured) saltstone. Inspection of the mixer in January 2013 showed significant wear on the third, fourth and fifth paddle pairs after the conveying augers. A 2-inch Readco-Kurimoto continuous mixer was used to test alternate paddle configurations for use in the 10-inch mixer to decrease the wear rate on the paddles. Two wear tests were conducted to investigate a method of reducing wear on the mixer paddles. The first test (wear test 2a) had a paddle configuration similar to the currently installed 10-inch mixer in the SPF. This test established baseline wear. The second test (wear test 2b) had a reconfigured paddle arrangement that replaced the flat paddles with helical paddles for paddle pairs 2 - 6 and aligned paddle pair 1 with the augers. The intent of the reconfiguration was to more effectively convey the partially wetted dry feeds through the transition region and into the liquid feed where paddle wear is reduced due to dry feeds and salt solution being mixed at the intended water to premix ratio. The design of the helical paddles provides conveyance through the transition region to the liquid feed inlet. The alignment with the auger is aimed to provide a smoother transition (minimizing the discontinuity between the auger and paddle pair 1) into the downstream paddles. A soft metal with low wear resistance (6000 series aluminum) was used for the wear testing paddles to determine wear patterns while minimizing run time and maximizing wear rate. For the two paddle configurations tested using the scaled 2-inch Readco-Kurimoto continuous mixer, with the first six paddles after the augers replaced by the wear paddles and the remaining paddles were stainless steel. Since the 10-inch SPF mixer is designed with the liquid inlet centered over paddle pairs 5 and 6, the scaled 2-inch mixer was configured the

Electrochemical performance of Ni0.8Cu0.2/Ce0.8Gd0.2O1.9 cermet anodes with functionally graded structures for intermediate-temperature solid oxide fuel cell fueled with syngas

Science.gov (United States)

Miyake, Michihiro; Iwami, Makoto; Takeuchi, Mizue; Nishimoto, Shunsuke; Kameshima, Yoshikazu

2018-06-01

The electrochemical performance of layered Ni0.8Cu0.2/Ce0.8Gd0.2O1.9 (GDC) cermet anodes is investigated for intermediate-temperature solid oxide fuel cells (IT-SOFCs) at 600 °C using humidified (3% H2O) model syngas with a molar ratio of H2/CO = 3/2 as the fuel. From the results obtained, the electrochemical performance of the functionally graded multi-layered anodes is found to be superior to the mono-layered anodes. The test cell with a bi-layered anode consisting of 100 mass% Ni0.8Cu0.2/0 mass% GDC (10M/0E) and 70 mass% Ni0.8Cu0.2/30 mass% GDC (7M/3E) exhibits high power density. The test cell with a tri-layered anode consisting of 10M/0E, 7M/3E, and 50 mass% Ni0.8Cu0.2/50 mass% GDC (5M/5E) exhibits an even higher power density, suggesting that 10M/0E and 5M/5E layers contribute to the current collecting part and active part, respectively.

Stability and oxygen permeation behavior of Ce0.8Sm0.2O2−δ–La0.8Sr0.2CrO3−δ composite membrane under large oxygen partial pressure gradients

NARCIS (Netherlands)

Wang, Bo; Yi, Jianxin; Winnubst, Aloysius J.A.; Chen, Chusheng

2006-01-01

The stability and oxygen permeation behavior of the Ce0.8Sm0.2O2−δ–La0.8Sr0.2CrO3−δ dual-phase composite were investigated under a large oxygen gradient with one side of it exposed to air and the other side to CO, CH4 or H2 at elevated temperatures. An oxygen permeation flux of 8.6 × 10−7 mol cm−2

First principles simulation on the K0.8Fe2Se2 high-temperature structural superconductor

International Nuclear Information System (INIS)

Guo, Rui; Yang, Shizhong; Khosravi, Ebrahim; Zhao, Guang-Lin; Bagayoko, Diola

2013-01-01

Highlights: • The superconductor K 0.8 Fe 2 Se 2 super cell size, shape, and atomic positions are fully optimized using first principles density functional theory method. • Each K atom donates 0.8 |e| with K vacancies in the supercell, each Fe atom donates 0.4 |e|, while each Se atom gains 0.7 |e| ∼ 0.8 |e|. • Fe atoms show magnetic moment fluctuation and possible strong spin-orbital coupling. -- Abstract: Since the synthesis of the first ones in 2008, iron-based high temperature superconductors have been the subject of many studies. This great interest is partly due to their higher, upper magnetic field, smaller Fermi surface around the Γ point, and a larger coherence length. This work is focused on A x Fe 2 Se 2 structural superconductor (FeSe, 11 hierarchy; A = K, Cs) as recently observed. ARPES data show novel, electronic structure and a hole-free Fermi surface which is different from previously observed Fermi surface images. We use ab initio density functional theory method to simulate the electronic structure of the novel superconductor A x Fe 2 Se 2 . We compare this electronic structure with those of other Fe-based superconductors

Study on magnetic properties of (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) alloys

Science.gov (United States)

Tan, G. S.; Xu, H.; Yu, L. Y.; Tan, X. H.; Zhang, Q.; Gu, Y.; Hou, X. L.

2017-09-01

In the present work, (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) permanent alloys are prepared by melt-spinning method. The hard magnetic properties of (Nd0.8Ce0.2)2-xFe12Co2B (x = 0-0.6) alloys annealed at optimum temperatures have been investigated systematically. Depending on the Nd, Ce concentration, the maximum energy product ((BH)max) and remanence (Br) increase gradually with x in the range of 0 ≤ x ≤ 0.4, whereas decrease gradually in the alloys with 0.4 plays a certain role in the magnetization reversal behavior and can improve the microstructure of (Nd0.8Ce0.2)1.6Fe12Co2B alloy.

BENCH SCALE SALTSTONE PROCESS DEVELOPMENT MIXING STUDY

Energy Technology Data Exchange (ETDEWEB)

Cozzi, A.; Hansen, E.

2011-08-03

The Savannah River National Laboratory (SRNL) was requested to develop a bench scale test facility, using a mixer, transfer pump, and transfer line to determine the impact of conveying the grout through the transfer lines to the vault on grout properties. Bench scale testing focused on the effect the transfer line has on the rheological property of the grout as it was processed through the transfer line. Rheological and other physical properties of grout samples were obtained prior to and after pumping through a transfer line. The Bench Scale Mixing Rig (BSMR) consisted of two mixing tanks, grout feed tank, transfer pump and transfer hose. The mixing tanks were used to batch the grout which was then transferred into the grout feed tank. The contents of the feed tank were then pumped through the transfer line (hose) using a progressive cavity pump. The grout flow rate and pump discharge pressure were monitored. Four sampling stations were located along the length of the transfer line at the 5, 105 and 205 feet past the transfer pump and at 305 feet, the discharge of the hose. Scaling between the full scale piping at Saltstone to bench scale testing at SRNL was performed by maintaining the same shear rate and total shear at the wall of the transfer line. The results of scaling down resulted in a shorter transfer line, a lower average velocity, the same transfer time and similar pressure drops. The condition of flow in the bench scale transfer line is laminar. The flow in the full scale pipe is in the transition region, but is more laminar than turbulent. The resulting plug in laminar flow in the bench scale results in a region of no-mixing. Hence mixing, or shearing, at the bench scale should be less than that observed in the full scale, where this plug is non existent due to the turbulent flow. The bench scale tests should be considered to be conservative due to the highly laminar condition of flow that exists. Two BSMR runs were performed. In both cases, wall

Nanoparticles of La0.8Ca0.2Fe0.8Ni0.2O3-δ perovskite for solid oxide fuel cell application

International Nuclear Information System (INIS)

Ortiz-Vitoriano, N.; Ruiz de Larramendi, I.; Gil de Muro, I.; Ruiz de Larramendi, J.I.; Rojo, T.

2010-01-01

Polycrystalline samples of La 0.8 Ca 0.2 Fe 0.8 Ni 0.2 O 3-δ (LCFN) with perovskite type structure have been prepared by combustion, freeze drying, citrate-gel process and liquid mix method. The analysis of X-ray powder diffraction indicated that the samples were single phase and crystallized in an orthorhombic (space group, Pnma no. 62) structure. Transmission electron microscopy (TEM) analysis on the synthesized powder at 600 o C by liquid mix method showed clusters of 150 nm formed by nanoparticles of 20 nm. Electrochemical performance of LCFN cathodes, which are used for intermediate temperature solid oxide fuel cells, were investigated. The polarization resistance was studied using two different electrolytes: Y-doped zirconia (YSZ) and Sm-doped ceria (SDC). The dc four-probe measurement exhibits a total electrical conductivity, over 100 S cm -1 at T ≥ 600 o C, pointing out that strontium can be substituted for the cheaper calcium cation without destroying the electrochemical properties. Experimental results indicate that nanoparticles have more advantages in terms of smaller particle size and better electrochemical performance.

Mechanisms of contaminant migration from grouted waste

International Nuclear Information System (INIS)

Magnuson, S.O.; Yu, A.D.

1992-01-01

Low-level radioactive decontaminated salt solution is generated at the Savannah River Site (SRS) from the In-Tank Precipitation process. The solution is mixed with cement, slag, and fly ash, to form a grout, termed ''Saltstone'', that will be disposed in concrete vaults at the Saltstone Disposal Facility (SDF) [1]. Of the contaminants in the Saltstone, the greatest concern to SRS is the potential release of nitrate to the groundwater because of the high initial nitrate concentration (0.25 g/cm 3 ) in the Saltstone and the low Safe Drinking Water Act (SDWA) maximum contaminant level (MCL) of 44 mg/L. The SDF is designed to allow a slow, controlled release over thousands of years. This paper addresses a modeling study of nitrate migration from intact non-degraded concrete vaults in the unsaturated zone for the Radiological Performance Assessment (PA) of the SRS Saltstone Disposal Facility [3]. The PA addresses the performance requirements mandated by DOE Order 5820.2A [4

Ab initio investigation of isomerism, structure and stability of dimer molecules of (LiMgH3)2 and (LiMgF3)2salts and their fragments

International Nuclear Information System (INIS)

Charkin, O.P.; Klimenko, N.M.; MakKi, M.L.

2000-01-01

Ab initio calculations of potential energy surfaces in neighborhood of key structures of non rigid dimer molecules of lithium salts of (LiMgX 3 ) 2 and binuclear anions Mg 2 X 5 - , dianions MgX 6 2- and molecules Mg 2 X 4 (X=H, F) are done in the framework of QCI-SD(T)/6-31(+)G**//MP2/6-31G* + ZPE(MP2/6-31G*) and MP2/6-31G*//HF/6-31G* + ZPE(HF/6-31G*) approximations. Equilibrium geometric parameters, relative energy and energy of decomposition of isomers, frequencies and IR-intensities of normal vibrations are determined. Data obtained are compared with results of analogous calculations for beryllium related compounds [ru

Structural and compositional optimization of the LiNi0.8Co0.2O2 electrode by new synthesis conditions

International Nuclear Information System (INIS)

Mosqueda L, Y.; Milian P, C. R.; Pomares A, M.; Rodriguez H, J.; Perez C, E.

2012-01-01

The optimization of citrate precursor method to obtain the LiNi 0.8 Co 0.2 O 2 oxide from the thermal decomposition of the citrate precursor (NH 4 ) 3 LiNi 0.8 Co 0.2 (C 6 H 5 O 7 ) is presented. The optimization procedure consists of both the lithium atmosphere and the reaction time control during the decomposition of the citrate precursor. Were obtained and characterized two kind of the (Li l-x Ni x )(Ni 0.8 Co 0.2 )O 2 oxides, with and without optimized synthesis conditions, identified as A and B oxides, respectively. The A and B oxides are characterized by compositional, structural and electrochemical studies. The results showed that is possible to reach the ordered oxide phase at smaller reaction time if the lithium atmosphere is controlled. From the combination of the chemical analysis by Icp and the DRX Rietveld structural refinement it is possible to establish the Li, Ni(II), Ni(III) and Co(III) composition with great accuracy. The resulted structural and compositional transformations have a close relation with technological parameters of the rechargeable lithium battery using Li Ni 0.8 Co 0.2 O 2 oxide as cathode. (Author)

Microwave dielectric properties of (Ca0.8Sr0.2)(SnxTi1−x)O3 ceramics

International Nuclear Information System (INIS)

Hsu, Cheng-Hsing; Chang, Chia-Hao

2013-01-01

Highlights: ► New microwave dielectric properties of (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 ceramics were investigated. ► A single-phase solid solution containing orthorhombic Pbnm with different Sn contents was formed. ► A significant improvement of Q × f value and τ f were achieved by (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 system. ► Second phases were formed and affected the dielectric properties of (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 system. ► Low cost and suitable τ f value of (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 demonstrate a good potential for use in microwave device. -- Abstract: In this paper, we study the behavior of the B-site behavior with the incorporation of Sn 4+ ion in (Ca 0.8 Sr 0.2 )TiO 3 ceramics. An excess of Sn 4+ resulted in the formation of a secondary phase of CaSnO 3 and SrSnO 3 affecting the microwave dielectric properties of the (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 ceramics. The dielectric properties of the (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 ceramics were improved because of the solid solution of Sn 4+ substitution in the B-site. The temperature coefficient of resonant frequency (τ f ) of the (Ca 0.8 Sr 0.2 )(Sn x Ti 1−x )O 3 ceramics also improved with increasing Sn content

Raman scattering from In0.2Ga0.8N/GaN superlattices

International Nuclear Information System (INIS)

Kisoda, Kenji; Hirakura, Kohji; Harima, Hiroshi

2006-01-01

We have performed Raman scattering experiments on high quality In 0.2 Ga 0.8 N/GaN superlattices(SLs). The A 1 LO phonon mode from the In 0.2 Ga 0.8 N layer was observed in the Mg doped SL. This was attributable to manifestation of a resonance enhancement via acceptor levels formed by magnesium doping. The peak frequency of the A 1 LO mode shifted to high frequency side with the excitation energy. The frequency shift suggested that the composition of indium was fluctuated along the growth direction in the InGaN layer. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Magnetic ordering and electrical resistivity in Co0.2Zn0.8Fe2O4 spinel oxide

International Nuclear Information System (INIS)

Bhowmik, R.N.; Ranganathan, R.; Ghosh, B.; Kumar, S.; Chattopadhyay, S.

2008-01-01

We report the magnetic, Moessbauer spectroscopy and resistivity measurements in order to understand the electronic behaviour of bulk Co 0.2 Zn 0.8 Fe 2 O 4 spinel oxide. The effect of magnetic order on electrical behaviour is observed from the resistivity measurements in the absence and presence of magnetic field. The analysis of Moessbauer spectra suggests the absence of Fe 2+ ions in the system, which implies that complete hopping of charge carriers between localized Fe 3+ /Co 2+ and Fe 2+ /Co 3+ pair of ions in B sublattice is not the favourable mechanism in Co 0.2 Zn 0.8 Fe 2 O 4 . We suggest that electrical behaviour of the present sample may be consistent with a model of fractional charge transfer via Fe B 3+ -O 2- -Co B 2+ superexchange path

Electrochemical cleaning of Sv-08G2S wire surface

International Nuclear Information System (INIS)

Kozlov, E.I.; Degtyarev, V.G.; Novikov, M.P.

1981-01-01

Results of industrial tests of the Sv-08G2S wire with different state of surface fwith technological lubrication, after mechanical cleaning, with electrochemically cleaned surface) are presented. Advantages of welding-technological properties of the wire with electroe chemically cleaned surface are shown. An operation principle of the electrochemical cleaning facility is described. A brief specf ification f of the facility is given [ru

Grain refining effect of magnetic field on Mg2Ni0.8Mn0.2 hydrogen storage alloys during rapid quenching

International Nuclear Information System (INIS)

Jiang, Chenxi; Wang, Haiyan; Chen, Xiangrong; Tang, Yougen; Lu, Zhouguang; Wang, Yazhi; Liu, Zuming

2013-01-01

The effect of static magnetic field treatment for synthesis of Mg 2 Ni 0.8 Mn 0.2 alloys during rapid quenching was investigated in this paper. X-ray diffraction (XRD) and scanning electron microscope (SEM) results show that the transversal static magnetic field can effectively refine the grain size, producing nanocrystalline inside. This distinct phenomenon is probably attributed to the Lorentz force suppressing the crystallization of the hydrogen storage alloys and the thermoelectric effect. Mainly due to the grain refinement, the discharge capacity of Mg 2 Ni 0.8 Mn 0.2 alloy is raised from 79 to about 200 mA h g −1 . It is confirmed that Mg 2 Ni 0.8 Mn 0.2 alloy by magnetic field assisted approach possesses enhanced electrochemical kinetics and relatively high corrosion resistance against the alkaline solution, thus resulting in higher electrochemical properties

Transport properties of S0.8Se16M0.2 (M = Al, Ag or Cu) system

International Nuclear Information System (INIS)

Wahab, L.A.

2003-01-01

The results are presented of a study of the electrical and optical properties of vacuum evaporated amorphous thin films in the S 0.8 Se 16 M 0.2 (M=Al, Ag or Cu) system. The activation energy and the pre-exponential factor which appear in the dc conductivity are found to be higher in case of Cu than in case of Ag and Al. The reflectance and transmission are used to measure the optical gap. The glass S 0.8 Se 16 Cu 0.2 behaves as a quasi intrinsic semiconductor (the electrical activation energy is about half of the optical gap). The electrical activation energy is about one-third of the optical gap for the chalcogenide glasses S 0.8 Se 16 Al 0.2 and S 0.8 Se 16 Ag 0.2 . The variation in the refractive index and the imaginary part of the dielectric constant with photon energy have also been reported. The influence of composition on the investigated parameters is reported

Ab initio investigation of isomerism, structure and stability of dimer molecules of Beryllate salts (LiBeH3)2, (LiBeF3)2 and their fragments

International Nuclear Information System (INIS)

Charkin, O.P.; Klimenko, N.M.; MakKi, M.L.

2000-01-01

In the framework of correlated approximation method QCI-SD(T)/6-31(+)G** + ZPE(MP2/6-31G*) and MP2/6-31(+)G* + ZPE(HF/6-31G*) ab initio calculations of surfaces and potential energy in the surroundings of key structures of not rigid dimer molecules of beryllate and fluoroberyllate complex salts (LiBeX 3 ) 2 , binuclear anions Be 2 X 5 - , dianions Be 2 X 6 2- and molecules Be 2 X 4 (X=H, F) are done. Equilibrium geometrical parameters of isomers, frequencies and relative IR intensities of normal vibrations, their relative energies and decomposition energies are determined. Similarity and differences of hydrides and fluorides, deformation and polarization of anions under cation effect in the case of their different mutual orientation are analyzed [ru

Electronic and ionic transport in Ce0.8PrxTb0.2-xO2-δ and evaluation of performance as oxygen permeation membranes

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Hendriksen, Peter Vang

2012-01-01

is significantly enhanced relative to that of a Ce0.9Gd0.1O1.95-δ membrane at high oxygen activities of the permeate gas (aO2 an > 10-15) due to the enhanced electronic conductivity of the Ce0.8PrxTb0.2-xO2-δ compounds. Interference between the ionic and electronic flows has a significant positive effect......The electronic conductivity of Ce0.8PrxTb0.2-xO2-δ (x = 0, 0.05, 0.10, 0.15, 0.20) was determined in the oxygen activity range aO2 ≈ 103 to aO2 ≈ 10-17 at 700- 900 °C by means of Hebb-Wagner polarisation. The electronic conductivity of all the Ce0.8PrxTb0.2-xO2-δ compositions was significantly...... enhanced as compared to that of Ce0.9Gd0.1O1.95-δ, and its value was found to increase with increasing Pr/Tb ratio. The ionic mobility of Ce0.8PrxTb0.2-xO2-δ is similar to that of Ce1- 2δGd2δO2-δ at the same oxygen vacancy concentration. The calculated oxygen flux of a Ce0.8PrxTb0.2-xO2-δ membrane...

Design of Rh/Ce0.2Zr0.8O2-Al2O3 nanocomposite for ethanol steam reforming

International Nuclear Information System (INIS)

De Rogatis, Loredana; Montini, Tiziano; Casula, Maria F.; Fornasiero, Paolo

2008-01-01

Rh(1 wt.%)/Ce 0.2 Zr 0.8 O 2 (10 wt.%)-Al 2 O 3 nanocomposite has been investigated as active and thermally stable catalyst for ethanol steam reforming. Rh nanoparticles were synthesised by surfactant assisted route, using N-hexadecyl-N-(2-hydroxyethyl)-N,N-dimethyl ammonium bromide (HEAC16Br). Metal particles with average diameter of 2.1 nm were obtained at 0.53 Rh/HEAC16Br molar ratio, while increasing the amount of surfactant lead to formation of larger particles. The preformed Rh nanoparticles have been effectively embedded into a porous layer of nanocomposite oxides. Low temperature H 2 chemisorption experiments and activity data confirm that most of the Rh atoms are accessible to the reaction mixture. The Ce 0.2 Zr 0.8 O 2 mixed oxide inhibits the dehydration of ethanol to ethylene and favours the water gas shift reaction. The alumina ensures good thermal stability and high surface area of the catalyst. No significant deactivation is observed after repeated run-up and run-down experiments

Comparative studies of the dielectric properties of (1−x)BiFeO{sub 3}-xNi{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} (x=0.0, 0.2, 0.5, 0.8, 1.0) multiferroic nanocomposite with their single phase BiFeO{sub 3} and Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}

Energy Technology Data Exchange (ETDEWEB)

Mani, Angom Devadatta, E-mail: angomdevadattamani@gmail.com; Soibam, Ibetombi

2017-02-15

BiFeO{sub 3} (BFO) and nickel zinc ferrite Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} (NZFO) were prepared by sol gel and auto combustion route respectively. Stoichiometric proportions were mixed to obtain the multiferroic nanocomposites having the compositional formula (1−x)BiFeO{sub 3}-x Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} (x=0.0, 0.2, 0.5, 0.8, 1.0). The phases were confirmed by XRD analyses. SEM micrographs showed the agglomerated nature of the particles with continuous grain growth in all directions. Elemental compositions were confirmed from EDAX studies. FTIR studies showed the stretching and bending vibrations of the various bonds present in the samples. The dielectric properties such as dielectric constant, ε′ and dielectric loss tangent, tanδ were studied for the spinel, perovskite and nanocomposite ferrites. Experimental result shows an increasing trend in the value of dielectric constant in going from spinel to perovskite phase. The frequency dependence of tanδ showed minimum loss for x=0.5 nanocomposite. Possible mechanisms explaining the above results were being discussed.

Magnetic properties and magnetocaloric effects in Mn1.2Fe0.8P1-xGex compounds

International Nuclear Information System (INIS)

Ou, Z Q; Wang, G F; Lin Song; Tegus, O; Brueck, E; Buschow, K H J

2006-01-01

We have studied the magnetic properties and magnetocaloric effects in the Mn 1.2 Fe 0.8 P 1-x Ge x compounds with x = 0.2, 0.22, 0.3, 0.4 and 0.5. X-ray diffraction patterns show that the Mn 1.2 Fe 0.8 P 1-x Ge x compounds crystallize in the hexagonal Fe 2 P-type crystal structure. The magnetic moments of the Mn 1.2 Fe 0.8 P 1-x Ge x compounds measured at 5 K and 5 T increase with increasing Ge content. The Curie temperature increases strongly and the magnetic entropy change has a maximum around 233 K for the compound with x = 0.22, which is about 19 and 31 J kg -1 K -1 for a field change of 2 and 5 T, respectively

Properties of half metallic (Ba0.8Sr0.2)2-x La2x/3x/3FeMoO6 double perovskites

International Nuclear Information System (INIS)

Serrate, D.; De Teresa, J.M.; Blasco, J.; Morellon, L.; Ibarra, M.R.

2005-01-01

Previous work in (Ba 0.8 Sr 0.2 ) 2- x La x FeMoO 6 and Ba 1+ x Sr 1-3 x La 2 x FeMoO 6 have stated electron doping as the most important parameter in terms of T c enhancement. Here we report complementary structural, magnetic and transport properties, say a series where there is no doping and only structural parameters are changed: (Ba 0.8 Sr 0.2 ) 2- x La 2 x /3 x /3 FeMoO 6 . We propose a complete phase diagram where structural and bandfilling impact on the Curie temperature is clearly evidenced

Preparation and characterizations of Ba0.8Ca0.2TiO3 by complex polymerization method (CPM)

International Nuclear Information System (INIS)

Motta, F.V.; Marques, A.P.A.; Escote, M.T.; Melo, D.M.A.; Ferreira, A.G.; Longo, E.; Leite, E.R.; Varela, J.A.

2008-01-01

Ba 0.8 Ca 0.2 TiO 3 (BCT) was prepared by the complex polymerization method (CPM) using Ba 0.8 Ca 0.2 CO 3 and [Ti[OCH(CH 3 ) 2 ] 4 as starting materials. The powders were crystallized at several temperatures from 400 to 1200 deg. C using different times (from 1 to 8 h). The phase evolution and the physical properties were characterized by X-ray diffraction, Raman and IR spectroscopy. Such results indicate that the precursor Ba 0.8 Ca 0.2 CO 3 used in the synthesis of Ba 0.8 Ca 0.2 TiO 3 promotes an effective complexation of the ions Ca 2+ in the matrix of BaTiO 3 . After heat treatment for 2 h at 600 deg. C the phase BCT was obtained with absence of the CaTiO 3 or BaCO 3 phases. The CPM is an efficient method in the synthesis of the BCT, using small reaction time and low temperature and cost for the preparation of these powders

A screen-printed Ce 0.8Sm 0.2O 1.9 film solid oxide fuel cell with a Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ cathode

Science.gov (United States)

Zhang, Yaohui; Huang, Xiqiang; Lu, Zhe; Liu, Zhiguo; Ge, Xiaodong; Xu, Jiahuan; Xin, Xianshuang; Sha, Xueqing; Su, Wenhui

Screen-printing technology was developed to fabricate Ce 0.8Sm 0.2O 1.9 (SDC) electrolyte films onto porous NiO-SDC green anode substrates. After sintering at 1400 °C for 4 h, a gas-tight SDC film with a thickness of 12 μm was obtained. A novel cathode material of Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ was subsequently applied onto the sintered SDC electrolyte film also by screen-printing and sintered at 970 °C for 3 h to get a single cell. A fuel cell of Ni-SDC/SDC (12 μm)/Ba 0.5Sr 0.5Co 0.8Fe 0.2O 3- δ provides the maximum power densities of 1280, 1080, 670, 370, 180 and 73 mW cm -2 at 650, 600, 555, 505, 455 and 405 °C, respectively, using hydrogen as fuel and stationary air as oxidant. When dry methane was used as fuel, the maximum power densities are 876, 568, 346 and 114 mW cm -2 at 650, 600, 555 and 505 °C, respectively. The present fuel cell shows excellent performance at lowered temperatures.

Synthesis of nanocrystalline nickel-zinc ferrite (Ni0.8Zn0.2Fe2O4) thin films by chemical bath deposition method

International Nuclear Information System (INIS)

Pawar, D.K.; Pawar, S.M.; Patil, P.S.; Kolekar, S.S.

2011-01-01

Graphical abstract: Display Omitted Research highlights: → We have successfully synthesized nickel-zinc ferrite (Ni 0.8 Zn 0.2 Fe 2 O 4 ) thin films on stainless steel substrates using a low temperature chemical bath deposition method. → The surface morphological study showed the compact flakes like morphology. → The as-deposited thin films are hydrophilic (10 o o ) whereas the annealed thin films are super hydrophilic (θ o ) in nature. → Ni 0.8 Zn 0.2 Fe 2 O 4 thin films could be used in supercapacitor. - Abstract: The nickel-zinc ferrite (Ni 0.8 Zn 0.2 Fe 2 O 4 ) thin films have been successfully deposited on stainless steel substrates using a chemical bath deposition method from alkaline bath. The films were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), static water contact angle and cyclic voltammetry measurements. The X-ray diffraction pattern shows that deposited Ni 0.8 Zn 0.2 Fe 2 O 4 thin films were oriented along (3 1 1) plane. The FTIR spectra showed strong absorption peaks around 600 cm -1 which are typical for cubic spinel crystal structure. SEM study revealed compact flakes like morphology having thickness ∼1.8 μm after air annealing. The annealed films were super hydrophilic in nature having a static water contact angle (θ) of 5 o .The electrochemical supercapacitor study of Ni 0.8 Zn 0.2 Fe 2 O 4 thin films has been carried out in 6 M KOH electrolyte. The values of interfacial and specific capacitances obtained were 0.0285 F cm -2 and 19 F g -1 , respectively.

Crystal structure of superparamagnetic Mg0.2Ca0.8Fe2O4 nanoparticles synthesized by sol–gel method

International Nuclear Information System (INIS)

Escamilla-Pérez, A.M.; Cortés-Hernández, D.A.; Almanza-Robles, J.M.; Mantovani, D.; Chevallier, P.

2015-01-01

Powders of magnetic iron oxide nanoparticles (Mg 0.2 Ca 0.8 Fe 2 O 4 ) were prepared by a sol–gel method using ethylene glycol and nitrates of Fe, Ca and Mg as starting materials. Those powders were heat treated at different temperatures (573, 673, 773 and 873 K). In order to evaluate the effect of the heat treatment temperature on the nanoferrites properties, X-ray diffraction (XRD), vibrating sample magnetometry (VSM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques were used. It was found that the reaction products exhibit nanometric sizes and superparamagnetic behavior. It is also demonstrated that, as the heat treatment temperature increases, the particle size and the saturation magnetization of the nanoferrites are increased. - Highlights: • Mg 0.2 Ca 0.8 Fe 2 O 4 superparamagnetic nanoparticles were successfully synthesized. • Particle average sizes of Ca–Mg ferrites were within the range of 8–25 nm. • The nanoferrite treated at 873 K showed a stoichiometry close to Mg 0.2 Ca 0.8 Fe 2 O 4 . • The heat treatment temperature has a strong effect on the crystal structure. • These nanoparticles are potential materials for magnetic hyperthermia

Giant room-temperature magnetoresistance in La0.8Tb0.2MnO3 under the low magnetic fields

International Nuclear Information System (INIS)

Zhang Yingtang; Chen Ziyu; Wang Chunchang; Jie Qiu; Lue Huibin

2009-01-01

Polycrystalline perovskite La 0.8 Tb 0.2 MnO 3 (LTMO) with an orthorhombic phase was synthesized by conventional solid-state reaction. The magnetic and electric properties of La 0.8 Tb 0.2 MnO 3 were examined. The striking finding is that the material exhibits giant magnetoresistance at room temperature as high as -31.8% and -35.7% under the low magnetic fields of 100 and 1000 Oe, respectively. This result suggests that La 0.8 Tb 0.2 MnO 3 has a promising potential in future device developments

Oxygen Nonstoichiometry and Defect Chemistry Modeling of Ce0.8Pr0.2O2-delta

OpenAIRE

Chatzichristodoulou, Christodoulos; Hendriksen, Peter Vang

2010-01-01

The oxygen nonstoichiometry (delta) of Ce0.8Pr0.2O2−delta has been measured as a function of PO2 at temperatures between 600 and 900°C by coulometric titration and thermogravimetry. An ideal solution defect model, a regular solution model, and a defect association model, taking into account the association of reduced dopant species and oxygen vacancies, were unable to reproduce the experimental results. However, excellent agreement with the experimentally determined oxygen nonstoichiometry co...

Structural and compositional optimization of the LiNi{sub 0.8}Co{sub 0.2}O{sub 2} electrode by new synthesis conditions

Energy Technology Data Exchange (ETDEWEB)

Mosqueda L, Y.; Milian P, C. R.; Pomares A, M.; Rodriguez H, J.; Perez C, E., E-mail: yodalgis@imre.oc.uh.cu [Havana University, Institute of Materials Science and Technology, Zapata y G, Plaza de la Revolucion, Vedado, 10400 Havana (Cuba)

2012-07-01

The optimization of citrate precursor method to obtain the LiNi{sub 0.8}Co{sub 0.2}O{sub 2} oxide from the thermal decomposition of the citrate precursor (NH{sub 4}){sub 3}LiNi{sub 0.8}Co{sub 0.2}(C{sub 6}H{sub 5}O{sub 7}) is presented. The optimization procedure consists of both the lithium atmosphere and the reaction time control during the decomposition of the citrate precursor. Were obtained and characterized two kind of the (Li{sub l-x}Ni{sub x})(Ni{sub 0.8}Co{sub 0.2})O{sub 2} oxides, with and without optimized synthesis conditions, identified as A and B oxides, respectively. The A and B oxides are characterized by compositional, structural and electrochemical studies. The results showed that is possible to reach the ordered oxide phase at smaller reaction time if the lithium atmosphere is controlled. From the combination of the chemical analysis by Icp and the DRX Rietveld structural refinement it is possible to establish the Li, Ni(II), Ni(III) and Co(III) composition with great accuracy. The resulted structural and compositional transformations have a close relation with technological parameters of the rechargeable lithium battery using Li Ni{sub 0.8}Co{sub 0.2}O{sub 2} oxide as cathode. (Author)

Structural phase transition and multiferroic properties of Bi0.8A0.2Fe0.8Mn0.2O3 (A = Ca, Sr)

Science.gov (United States)

Rout, Jyoshna; Choudhary, R. N. P.

2018-05-01

The multiferroic BiFeO3 and Bi0.8A0.2Fe0.8Mn0.2O3 (A = Ca, Sr) have been synthesized using direct mechanosynthesis. Detailed investigations were made on the influence of Ca-Mn and Sr-Mn co-substitutions on the structure change, electric and magnetic properties of the BFO. Rietveld refinement on the XRD pattern of the modified samples clarifies the structural transition from R3c:H (parent BiFeO3) to the biphasic structure (R3c: H + Pnma). Scanning electron micrographs confirmed the polycrystalline nature of the materials and each of the microstructure comprised of uniformly distributed grains with less porosity. The dielectric measurements reveal that enhancement in dielectric properties due to the reduction of oxygen vacancies by substitutional ions. Studies of frequency-dependence of impedance and related parameters exhibit that the electrical properties of the materials are strongly dependent on temperature, and bear a good correlation with its microstructure. The bulk resistance (evaluated from impedance studies) is found to decrease with increasing temperature for all the samples. The alternating current (ac) conductivity spectra show a typical signature of an ionic conducting system, and are found to obey Jonscher's universal power law. Preliminary studies of magnetic characteristics of the samples reveal enhanced magnetization for Ca-Mn co-substituted sample. The magnetoelectric coefficient as the function of applied dc magnetizing field under fixed ac magnetic field 15.368 Oe is measured and this ME coefficient αME corresponds to induction of polarization by a magnetic field.

Ultrathin ZnO interfacial passivation layer for atomic layer deposited ZrO2 dielectric on the p-In0.2Ga0.8As substrate

Science.gov (United States)

Liu, Chen; Lü, Hongliang; Yang, Tong; Zhang, Yuming; Zhang, Yimen; Liu, Dong; Ma, Zhenqiang; Yu, Weijian; Guo, Lixin

2018-06-01

Interfacial and electrical properties were investigated on metal-oxidesemiconductor capacitors (MOSCAPs) fabricated with bilayer ZnO/ZrO2 films by atomic layer deposition (ALD) on p-In0.2Ga0.8As substrates. The ZnO passivated In0.2Ga0.8As MOSCAPs have exhibited significantly improved capacitance-voltage (C-V) characteristics with the suppressed "stretched out" effect, increased accumulation capacitance and reduced accumulation frequency dispersion as well as the lower gate leakage current. In addition, the interface trap density (Dit) estimated by the Terman method was decreased dramatically for ZnO passivated p-In0.2Ga0.8As. The inherent mechanism is attributed to the fact that an ultrathin ZnO IPL employed by ALD prior to ZrO2 dielectric deposition can effectively suppress the formation of defect-related low-k oxides and As-As dimers at the interface, thus effectively improving the interface quality by largely removing the border traps aligned near the valence band edge of the p-In0.2Ga0.8As substrate.

Study of the Effect of (U0.8Pu0.2O2 Uranium–Plutonium Mixed Fuel Fission Products on a Living Organism

Directory of Open Access Journals (Sweden)

Ayagoz Baimukhanova

2016-08-01

Full Text Available The article describes the results of experiments conducted on pigs to determine the effect of plutonium, which is the most radiotoxic and highly active element in the range of mixed fuel (U0.8Pu0.2O2 fission products, on living organisms. The results will allow empirical prediction of the emergency plutonium radiation dose for various organs and tissues of humans in case of an accident in a reactor running on mixed fuel (U0.8Pu0.2O2.

Effect of buffer thickness on properties of In0.8Ga0.2As/InP with two-step growth technique

International Nuclear Information System (INIS)

Zhang Tiemin; Miao Guoqing; Jin Yixin; Yu Shuzhen; Jiang Hong; Li Zhiming; Song Hang

2009-01-01

In 0.8 Ga 0.2 As was grown by low-pressure metalorganic chemical vapor deposition (LP-MOCVD) on InP(1 0 0) substrate with two-step growth technique. Effect of buffer thickness on crystalline quality, surface morphology, electrical property and stress of In 0.8 Ga 0.2 As epilayer was analyzed, and properties of the In 0.8 Ga 0.2 As epilayer were characterized by X-ray diffraction, scanning electron microscopy, Hall measurements and Raman scattering. The experiments showed that the properties of the In 0.8 Ga 0.2 As epilayer had close relation to the buffer thickness and the optimum buffer thickness was about 100 nm

Structure-activity relationships for flavone interactions with amyloid β reveal a novel anti-aggregatory and neuroprotective effect of 2',3',4'-trihydroxyflavone (2-D08).

Science.gov (United States)

Marsh, Dylan T; Das, Sukanya; Ridell, Jessica; Smid, Scott D

2017-07-15

Naturally-occurring flavonoids have well documented anti-aggregatory and neuroprotective properties against the hallmark toxic protein in Alzheimer's disease, amyloid β (Aβ). However the extensive diversity of flavonoids has limited the insight into the precise structure-activity relationships that confer such bioactive properties against the Aβ protein. In the present study we have characterised the Aβ binding properties, anti-aggregatory and neuroprotective effects of a discreet set of flavones, including the recently described novel protein sumoylation inhibitor 2',3',4'-trihydroxyflavone (2-D08). Quercetin, transilitin, jaceosidin, nobiletin and 2-D08 were incubated with human Aβ 1-42 for 48h in vitro and effects on Aβ fibrillisation kinetics and morphology measured using Thioflavin T (ThT) and electron microscopy respectively, in addition to effects on neuronal PC12 cell viability. Of the flavones studied, only quercetin, transilitin and 2-D08 significantly inhibited Aβ 1-42 aggregation and toxicity in PC12 cells. Of those, 2-D08 was the most effective inhibitor. The strong anti-amyloid activity of 2-D08 indicates that extensive hydroxylation in the B ring is the most important determinant of activity against β amyloid within the flavone scaffold. The lack of efficacy of jaceosidin and nobiletin indicate that extension of B ring hydroxylation with methoxyl groups result in an incremental loss of anti-fibrillar and neuroprotective activity, highlighting the constraint to vicinal hydroxyl groups in the B ring for effective inhibition of aggregation. These findings reveal further structural insights into anti-amyloid bioactivity of flavonoids in addition to a novel and efficacious anti-aggregatory and neuroprotective effect of the semi-synthetic flavone and sumoylation inhibitor 2',3',4'-trihydroxyflavone (2-D08). Such modified flavones may facilitate drug development targeting multiple pathways in neurodegenerative disease. Crown Copyright © 2017

Electrochemical characterization of La0.6Ca0.4Fe0.8Ni0.2O3 cathode on Ce0.8Gd0.2O1.9 electrolyte for IT-SOFC

DEFF Research Database (Denmark)

Ortiz-Vitoriano, N.; Bernuy-Lopez, C.; Hauch, Anne

2014-01-01

For Solid Oxide Fuel Cells (SOFCs) to become an economically attractive energy conversion technology, suitable materials and structures which enable operation at lower temperatures, while retaining high cell performance, must be developed. Recently, the perovskitetype La0.6Ca0.4Fe0.8Ni0.2O3 oxide...... has shown potential as an intermediate temperature SOFC cathode. An equivalent circuit describing the cathode polarization resistances was constructed from analyzing impedance spectra recorded at different temperatures in oxygen. A competitive electrode polarization resistance is reported...... for this oxygen electrode using a Ce0.8Gd0.2O1.9 electrolyte, determined by impedance spectroscopy studies of symmetrical cells sintered at 800 _C and 1000 _C. Scanning electron microscopy (SEM) studies of the symmetrical cells revealed the absence of any reaction layer between cathode and electrolyte...

TOP 08 2 503 Low Volatility Agent Permeation (LVAP) Swatch Testing

Science.gov (United States)

2018-02-20

tipped needle, Type 3, and a repeating Dispenser ( product PB-600), all manufactured by Hamilton® company, Reno, Nevada). TOP 08-2-503 20 February... Production Document CWA chemical warfare agent DA Department of the Army DEET N,N-diethyl-meta-toluamide DI deionized DoE design of experiment DPG U.S...under varying conditions of field use, storage, and/or environmental exposure(s). These procedures are designed to be used as part of an overall

Resistance switching mechanism of La_0_._8Sr_0_._2MnO_3_−_δ thin films

International Nuclear Information System (INIS)

Luo, X.D.; Gao, R.L.; Fu, C.L.; Cai, W.; Chen, G.; Deng, X.L.; Zhang, H.R; Sun, J.R.

2016-01-01

Effects of oxygen vacancies on the electrical transport properties of oxygen stoichiometric La_0_._8Sr_0_._2MnO_3 and oxygen-deficient La_0_._8Sr_0_._2MnO_3_−_δ films have been investigated. The result presents that the oxygen-deficient films annealed in vacuum show obvious increase of resistance and lattice parameter. With the sweeping voltage or temperature increasing, the resistance exhibits obvious bipolar switching effect, no forming process was needed. Oxygen deficiency in the annealed film leads to the formation of a structural disorder in the Mn–O–Mn conduction channel due to the accumulation of oxygen vacancies under high external electric field or temperatures and hence is believed to be responsible for the bipolar resistance switching effect and the enhanced resistivity compared with oxygen stoichiometric La_0_._8Sr_0_._2MnO_3 film. These results may be important for practical applications in photoelectric or storage devices and point to a useful direction for other oxidizing materials.

L-J phase in a Cu2.2Mn0.8Al alloy

Science.gov (United States)

Jeng, S. C.; Liu, T. F.

1995-06-01

A new type of precipitate (designated L-J phase) with two variants was observed within the (DO3 + L21) matrix in a Cu2.2Mn0.8Al alloy. Transmission electron microscopy examinations indicated that the L-J phase has an orthorhombic structure with lattice parameters a = 0.413 nm, b = 0.254 nm and c = 0.728 nm. The orientation relationship between the L-J phase and the matrix is (100)L-J//(011) m , (010)L-J//(111) m and (001)L-J//(211) m . The rotation axis and rotation angle between two variants of the L-J phase are [021] and 90 deg. The L-J phase has never been observed in various Cu-Al, Cu-Mn, and Cu-Al-Mn alloy systems before.

Nanomagnets La0.8Pb0.2(Fe0.8Co0.2)O3 assembled with a bonded surface graphene oxide: sensitive for sensing small gas molecules.

Science.gov (United States)

Bhargav, K K; Ram, S; Majumder, S B

2012-04-01

Nanocrystallites La0.8Pb0.2(Fe0.8Co0.2)O3 (LPFC) when bonded through a surface layer (carbon) in small ensembles display surface sensitive magnetism useful for biological probes, electrodes, and toxic gas sensors. A simple dispersion and hydrolysis of the salts in ethylene glycol (EG) in water is explored to form ensembles of the nanocrystallites (NCs) by combustion of a liquid precursor gel slowly in microwave at 70-80 dgrees C (apparent) in a closed container in air. In a dilute sample, the EG molecules mediate hydrolyzed species to configure in small groups in process to form a gel. Proposed models describe how a residual carbon bridges a stable bonded layer of a graphene-oxide-like hybrid structure on the LPFC-NCs in attenuating the magnetic structure. SEM images, measured from a pelletized sample which was used to study the gas sensing features in terms of the electrical resistance, describe plate shaped NCs, typically 30-60 nm widths, 60-180 nm lengths and -50 m2/g surface area (after heating at -750 degrees C). These NCs are arranged in ensembles (200-900 nm size). As per the X-ray diffraction, the plates (a Pnma orthorhombic structure) bear only small strain -0.0023 N/m2 and oxygen vacancies. The phonon and electronic bands from a bonded surface layer disappear when it is etched out slowly by heating above 550 degrees C in air. The surface layer actively promotes selective H2 gas sensor properties.

Effect of Chlorine Substitution on Sulfide Reactivity with OH Radicals

Science.gov (United States)

2008-09-01

Single point energy: MP2/6-311+G(3df,2p) (LRG) • Zero Point Energy from a vibrational frequency analysis: MP2/6-31++G** ( ZPE ) • Extrapolated energy...E(QCI) + E(LARG) – E(SML) + ZPE • Characterize the TS • Use a three-point fit methodology – fit a harmonic potential to three CCSD single point

Preliminary characterization of abandoned septic tank systems. Volume 2: Appendix D

International Nuclear Information System (INIS)

1995-12-01

In an effort to support remedial investigations of abandoned septic tanks by US DOE, this report contains the results of chemical analyses of the contents of these abandoned tanks. Analytical data are presented for the following: volatile/TCLP volatile organics; semivolatile/TCLP semivolatile organics; PCB organics; total petroleum hydrocarbons; and total metals. The abandoned systems potentially received wastes or effluent from buildings which could have discharged non-domestic, petroleum hydrocarbons, hazardous, radioactive and/or mixed wastes. The 20 sites investigated are located on the Nevada Test Site

Magnetoresistance properties of Fe0,2C0,8 composite materials pre and post gamma irradiated at 250 kGy dose

International Nuclear Information System (INIS)

Yunasfi; Setyo Purwanto; Wisnu A A

2009-01-01

Research about change of, magnetoresistance properties of Fe 0,2 C 0,8 composite materials pre and post gamma irradiation at a dose of 250 kGy was carried out. Fe 0,2 C 0,8 was prepared by mixing of Fe and C powder with the ratio of Fe : C set on 20:80 in weight %. In this research, the phase structure and magnetic properties of Fe 0,2 C 0,8 composite materials after 250 KGy dose of gamma irradiation have been measured and analyzed. The phase structure of Fe 0,2 C 0,8 was analyzed using X-ray diffractometer (XRD), whole the magnetoresistance properties was characterized using Four Point Probe method. The analyzing results showed the decreasing of X-ray diffraction peak intensity, but also in the same time showed the increasing of magnetoresistance properties after gamma irradiation. The enhancement of magnetoresistance value reached 5 times at 7,5 kOe magnetic field. This enhancement was caused due to structure defect within Fe 0,2 C 0,8 composite initiated by interaction between radiation of gamma ray and composite materials that further causes a change of magnetic interaction intensity in this materials. (author)

Giant strain with low cycling degradation in Ta-doped [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 lead-free ceramics

International Nuclear Information System (INIS)

Liu, Xiaoming; Tan, Xiaoli

2016-01-01

Non-textured polycrystalline [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2](Ti_1_−_xTa_x)O_3 ceramics are fabricated and their microstructures and electrical properties are characterized. Transmission electron microscopy reveals the coexistence of the rhombohedral R3c and tetragonal P4bm phases in the form of nanometer-sized domains in [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 with low Ta concentration. When the composition is x = 0.015, the electrostrain is found to be highly asymmetric under bipolar fields of ±50 kV/cm. A very large value of 0.62% is observed in this ceramic, corresponding to a large-signal piezoelectric coefficient d_3_3* of 1240 pm/V (1120 pm/V under unipolar loading). These values are greater than most previously reported lead-free polycrystalline ceramics and can even be compared with some lead-free piezoelectric single crystals. Additionally, this ceramic displays low cycling degradation; its electrostrain remains above 0.55% even after undergoing 10 000 cycles of ±50 kV/cm bipolar fields at 2 Hz. Therefore, Ta-doped [Bi_1_/_2(Na_0_._8K_0_._2)_1_/_2]TiO_3 ceramics show great potential for large displacement devices.

Electronic and Ionic Transport in Ce0.8PrxTb0.2−xO2−δ and Evaluation of Performance as Oxygen Permeation Membranes

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Hendriksen, Peter Vang

2012-01-01

to that of Ce0.9Gd0.1O1.95−δ, and was found to increase with increasing Pr/Tb ratio. The oxide ion mobility in Ce0.8PrxTb0.2−xO2−δ is similar to that in Ce1−2δGd2δO2−δ at the same oxygen vacancy concentration. Based on the measured ionic and electronic conductivities, fluxes through thin film Ce0.8PrxTb0.2−xO2......The electronic conductivity of Ce0.8PrxTb0.2−xO2−δ (x = 0, 0.05, 0.10, 0.15, 0.20) was determined in the oxygen activity range aO2 ≈ 103 – 10−17 at 700–900°C by Hebb-Wagner polarization. The electronic conductivity of all the Ce0.8PrxTb0.2−xO2−δ compositions was significantly enhanced as compared......−δ membranes were calculated. Calculated fluxes exceed 10 Nml min−1 cm−2 under oxyfuel relevant conditions (T = 800°C, aO2,permeate side = 10−3). Hence, in terms of transport properties, these materials are promising for this application. Interference between the ionic and electronic flows has...

Tritium release in Li{sub 4}SiO{sub 4} and Li{sub 4.2}Si{sub 0.8}Al{sub 0.2}O{sub 4} ceramics

Energy Technology Data Exchange (ETDEWEB)

Zhao, Linjie, E-mail: zhaolinjie1989@163.com; Long, Xinggui, E-mail: xingguil@caep.cn; Peng, Shuming, E-mail: pengshuming@caep.cn; Chen, Xiaojun; Xiao, Chengjian; Ran, Guangming; Li, Jiamao

2016-12-15

Li{sub 4+x}Si{sub 1−x}Al{sub x}O{sub 4} solid solution materials, which were designed as the advanced tritium breeders, were obtained by indirect solid state reactions. The behaviors of tritium release from Li{sub 4}SiO{sub 4} and Li{sub 4.2}Si{sub 0.8}Al{sub 0.2}O{sub 4} powders were investigated by temperature programmed desorption. The tritium release curves show different characteristics for the Li{sub 4}SiO{sub 4} and Li{sub 4.2}Si{sub 0.8}Al{sub 0.2}O{sub 4} ceramics. The main tritium release peak in the Li{sub 4}SiO{sub 4} and Li{sub 4.2}Si{sub 0.8}Al{sub 0.2}O{sub 4} powders is at approximately 600 °C after a high dose irradiation. Moreover, the temperature of the tritium release from Li{sub 4.2}Si{sub 0.8}Al{sub 0.2}O{sub 4} was lower than that of the release from Li{sub 4}SiO{sub 4}. This suggests a possible advantage to using the solid solutions as the advanced tritium breeding materials.

Neptunium sorption and co-precipitation of strontium in simulated DWPF salt solution

International Nuclear Information System (INIS)

McIntyre, P.F.; Orebaugh, E.G.; King, C.M.

1988-01-01

Batch experiments performed using crushed slag saltstone (∼40 mesh) removed >80% of 237 Np from simulated Defense Waste Processing Facility (DWPF) salt solution. The concentration of 237 Np (110 pCi/ml) used was 1000x greater than levels in actual DWPF solutions. Neptunium-239 was used as a tracer and was formed by neutron activation of uranyl nitrate. Results showed that small amounts of crushed saltstone (as little as 0.05 grams), removed >80% of neptunium from 15 ml of simulated DWPF solution after several hours equilibration. The neptunium is sorbed on insoluble carbonates formed in and on the saltstone matrix. Further testing showed that addition of 0.01 and 0.10 ml of 1 molar Ca +2 (ie. Ca (NO 3 ) 2 , CaCl 2 ) into 15 ml of simulated DWPF solution yielded a white carbonate precipitate which also removed >80% of the neptunium after 1 hour equilibration. Further experiments were performed to determine the effectiveness of this procedure to co-precipitate strontium

Microwave properties of La{sub 0.8}Ag{sub 0.2}MnO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Rostamnejadi, Ali [Malek Ashtar University of Technology, Electroceram Research Center, Shahin Shahr, Isfahan (Iran, Islamic Republic of)

2016-11-15

In this research, single-phase nanoparticles of La{sub 0.8}Ag{sub 0.2}MnO{sub 3} with mean particle size of 15 nm have been synthesized by sol-gel method. The microwave properties of La{sub 0.8}Ag{sub 0.2}MnO{sub 3}/paraffin nanocomposite are studied by measuring the complex permittivity and permeability in the frequency range of 1-18 GHz. The composite shows both reflection and absorption electromagnetic shielding effectiveness with maximum total value of 36 dB, which is suitable for defense and microwave radiation shielding applications at high temperatures. The electromagnetic absorption properties are described in terms of dielectric relaxation processes. (orig.)

Calorimetric investigation into interaction in Zr0.8Ti0.2CrFe-H2 system

International Nuclear Information System (INIS)

Sirotina, R.A.; Verbetskij, V.N.

1993-01-01

For studying Zr 0.8 Ti 0.2 CrFe-H 2 system is applied the calorimetric method with usage of the Tian-Calve type calorimeter. It is shown that up to 488 K in the system there are three characteristic regions: α (hydrogen solution in an intermetallic compounds (IMC)), β (hydrogen solution in a hydride) and α + β (region of coexistence of two phases). Temperature 448 K is near to critical one, when exceeding of which exists only hydrogen solution in a metal matrix. Pressure dependence of hydrogen content in IMC is described satisfactorily by a linear equation

Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing

Science.gov (United States)

2018-04-27

Final 3. DATES COVERED (From - To) 4. TITLE AND SUBTITLE Test Operations Procedure (TOP) 08-2-188 Chemical Point Detector Vapor Testing 5a. CONTRACT...NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK NUMBER 5f. WORK UNIT NUMBER 7. PERFORMING...ORGANIZATION NAME(S) AND ADDRESS(ES) US Army Dugway Proving Ground West Desert Test Center (TEDT-DPW) Dugway, UT 84022-5000 8. PERFORMING ORGANIZATION

Magnetic ordering and electrical resistivity in Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} spinel oxide

Energy Technology Data Exchange (ETDEWEB)

Bhowmik, R.N. [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700065 (India)], E-mail: rabindranath.bhowmik@saha.ac.in; Ranganathan, R. [Experimental Condensed Matter Physics Division, Saha Institute of Nuclear Physics, 1/AF, Bidhannagar, Kolkata 700065 (India); Ghosh, B.; Kumar, S. [Department of Physics, Jadavpur University, Kolkata 700 032 (India); Chattopadhyay, S. [Department of Physics, University of Calcutta, 92, A.P.C. Road, Kolkata 700009 (India)

2008-05-29

We report the magnetic, Moessbauer spectroscopy and resistivity measurements in order to understand the electronic behaviour of bulk Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} spinel oxide. The effect of magnetic order on electrical behaviour is observed from the resistivity measurements in the absence and presence of magnetic field. The analysis of Moessbauer spectra suggests the absence of Fe{sup 2+} ions in the system, which implies that complete hopping of charge carriers between localized Fe{sup 3+}/Co{sup 2+} and Fe{sup 2+}/Co{sup 3+} pair of ions in B sublattice is not the favourable mechanism in Co{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4}. We suggest that electrical behaviour of the present sample may be consistent with a model of fractional charge transfer via Fe{sub B}{sup 3+}-O{sup 2-}-Co{sub B}{sup 2+} superexchange path.

Temperature-dependent impedance spectroscopy of La0.8Sr0.2FeO3 nano-crystalline material

Science.gov (United States)

Kafa, C. A.; Triyono, D.; Laysandra, H.

2017-04-01

LaFeO3 is a material with perovskite structure which electrical properties frequently investigated. Research are done due to the exhibition of excellent gas sensing behavior through resistivity comparison from the p-type semiconductor. Sr doping on LaFeO3 or La1-xSrxFeO3 are able to improve the electrical conductivity through structural modification. Using Sr dopant concentration (x) of 0.2, La0.8Sr0.2FeO3 nano-crystal pellet was synthesized. The synthesis used sol-gel method, followed by gradual heat treatment and uniaxial compaction. XRD characterization shows that the structure of the sample is Orthorhombic Perovskite. Topography of the sample by SEM reveals grain and grain boundary existence with emerging agglomeration. The electrical properties of the material, as functions of temperature and frequency, were measured by Impedance Spectroscopy method using RLC meter, for temperatures of 303-373K. Through the Nyquist plot and Bode plot, the electrical conductivity of La0.8Sr0.2FeO3 is contributed by the grain and grain boundary. Finally, the electrical permittivities of La0.8Sr0.2FeO3 are increasing with temperature increase, with the highest achieved when measured at 1 kHz frequency.

Band Offset Measurements in Atomic-Layer-Deposited Al2O3/Zn0.8Al0.2O Heterojunction Studied by X-ray Photoelectron Spectroscopy.

Science.gov (United States)

Yan, Baojun; Liu, Shulin; Heng, Yuekun; Yang, Yuzhen; Yu, Yang; Wen, Kaile

2017-12-01

Pure aluminum oxide (Al 2 O 3 ) and zinc aluminum oxide (Zn x Al 1-x O) thin films were deposited by atomic layer deposition (ALD). The microstructure and optical band gaps (E g ) of the Zn x Al 1-x O (0.2 ≤ x ≤ 1) films were studied by X-ray diffractometer and Tauc method. The band offsets and alignment of atomic-layer-deposited Al 2 O 3 /Zn 0.8 Al 0.2 O heterojunction were investigated in detail using charge-corrected X-ray photoelectron spectroscopy. In this work, different methodologies were adopted to recover the actual position of the core levels in insulator materials which were easily affected by differential charging phenomena. Valence band offset (ΔE V ) and conduction band offset (ΔE C ) for the interface of the Al 2 O 3 /Zn 0.8 Al 0.2 O heterojunction have been constructed. An accurate value of ΔE V  = 0.82 ± 0.12 eV was obtained from various combinations of core levels of heterojunction with varied Al 2 O 3 thickness. Given the experimental E g of 6.8 eV for Al 2 O 3 and 5.29 eV for Zn 0.8 Al 0.2 O, a type-I heterojunction with a ΔE C of 0.69 ± 0.12 eV was found. The precise determination of the band alignment of Al 2 O 3 /Zn 0.8 Al 0.2 O heterojunction is of particular importance for gaining insight to the design of various electronic devices based on such heterointerface.

Dielectric behavior of samarium-doped BaZr0.2Ti0.8O3 ceramics

International Nuclear Information System (INIS)

Li, Yuanliang; Wang, Ranran; Ma, Xuegang; Li, Zhongqiu; Sang, Rongli; Qu, Yuanfang

2014-01-01

Graphical abstract: - Highlights: • We investigate dielectric properties and phase transition of Sm 3+ -doped BaZr 0.2 Ti 0.8 O 3 ceramics. • The additive amount of Sm 2 O 3 can greatly affect the dielectric properties. • The materials undergo a diffuse type ferroelectric phase transition. • There is an alternation of substitution preference of Sm 3+ ion for the host cations in perovskite lattice. - Abstract: The dielectric properties and phase transition of Sm 3+ -doped BaZr 0.2 Ti 0.8 O 3 (BZT20) ceramics were investigated. Room temperature X-ray diffraction study suggested that the compositions had single-phase cubic symmetry. Microstructure studies showed that the grain size decreased and that the Sm 2 O 3 amount markedly affected the dielectric properties of BZT20. A dielectric constant of 5700 at 0.2 mol% Sm 2 O 3 and a dissipation factor of only 0.0011 at 2 mol% Sm 2 O 3 were observed, indicating that BZT20 had significant potential applications. Moreover, the dielectric constant, dissipation factor, phase-transition temperature, and maximum dielectric constant increased with increased Sm 2 O 3 amount at ≤0.2 mol% Sm 2 O 3 but decreased with increased Sm 2 O 3 amount at >0.2 mol% Sm 2 O 3

Synthesis of nanocrystalline nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films by chemical bath deposition method

Energy Technology Data Exchange (ETDEWEB)

Pawar, D.K. [Department of Chemistry, Shivaji University, Kolhapur 416 004 (M.S.) (India); Pawar, S.M. [Department of Materials Science and Engineering, Chonnam National University, 500 757 (Korea, Republic of); Patil, P.S. [Department of Physics, Shivaji University, Kolhapur 416 004 (M.S.) (India); Kolekar, S.S., E-mail: kolekarss2003@yahoo.co.in [Department of Chemistry, Shivaji University, Kolhapur 416 004 (M.S.) (India)

2011-02-24

Graphical abstract: Display Omitted Research highlights: > We have successfully synthesized nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films on stainless steel substrates using a low temperature chemical bath deposition method. > The surface morphological study showed the compact flakes like morphology. > The as-deposited thin films are hydrophilic (10{sup o} < {theta} < 90{sup o}) whereas the annealed thin films are super hydrophilic ({theta} < 10{sup o}) in nature. > Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films could be used in supercapacitor. - Abstract: The nickel-zinc ferrite (Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4}) thin films have been successfully deposited on stainless steel substrates using a chemical bath deposition method from alkaline bath. The films were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), static water contact angle and cyclic voltammetry measurements. The X-ray diffraction pattern shows that deposited Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films were oriented along (3 1 1) plane. The FTIR spectra showed strong absorption peaks around 600 cm{sup -1} which are typical for cubic spinel crystal structure. SEM study revealed compact flakes like morphology having thickness {approx}1.8 {mu}m after air annealing. The annealed films were super hydrophilic in nature having a static water contact angle ({theta}) of 5{sup o}.The electrochemical supercapacitor study of Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} thin films has been carried out in 6 M KOH electrolyte. The values of interfacial and specific capacitances obtained were 0.0285 F cm{sup -2} and 19 F g{sup -1}, respectively.

Al{sub 0.2}Ga{sub 0.8}As X-ray photodiodes for X-ray spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Whitaker, M.D.C., E-mail: M.Whitaker@sussex.ac.uk; Lioliou, G.; Butera, S.; Barnett, A.M.

2016-12-21

Three custom-made Al{sub 0.2}Ga{sub 0.8}As p-i-n mesa X-ray photodiodes (200 µm diameter, 3 µm i layer) were electrically characterised and investigated for their response to illumination with soft X-rays from an {sup 55}Fe radioisotope X-ray source (Mn Kα = 5.9 keV; Mn Kβ = 6.49 keV). The AlGaAs photodiodes were shown to be suitable for photon counting X-ray spectroscopy at room temperature. When coupled to a custom-made low-noise charge-sensitive preamplifier, a mean energy resolution (as quantified by the full width at half maximum of the 5.9 keV photopeak) of 1.24 keV was measured at room temperature. Parameters such as the depletion width (1.92 µm at 10 V), charge trapping noise (61.7 e{sup −} rms ENC at 5 V, negligible at 10 V) and the electronic noise components (known dielectric noise (63.4 e{sup −} rms), series white noise (27.7 e{sup −} rms), parallel white noise (9.5 e{sup −} rms) and 1/f series noise (2.2 e{sup −} rms) at 10 V reverse bias) affecting the achieved energy resolution were computed. The estimated charge trapping noise and mean energy resolution were compared to similar materials (e.g. Al{sub 0.8}Ga{sub 0.2}As) previously reported, and discussed. These results are the first demonstration of photon counting X-ray spectroscopy with Al{sub 0.2}Ga{sub 0.8}As reported to date.

Giant room-temperature magnetoresistance in La{sub 0.8}Tb{sub 0.2}MnO{sub 3} under the low magnetic fields

Energy Technology Data Exchange (ETDEWEB)

Zhang Yingtang [Physics of Department, Beijing University of Aeronautics and Astronautics, Beijing 100083 (China); Institute of Physics and Center for Condensed Matter Physics, Chinese Academy of Sciences, Beijing 100080 (China); School of Material Science and Engineering, Shaanxi University of Technology, Hanzhong 723003 (China)], E-mail: zhangyingtang76@sina.com; Chen Ziyu [Physics of Department, Beijing University of Aeronautics and Astronautics, Beijing 100083 (China)], E-mail: chenzy@buaa.edu.cn; Wang Chunchang; Jie Qiu; Lue Huibin [Institute of Physics and Center for Condensed Matter Physics, Chinese Academy of Sciences, Beijing 100080 (China)

2009-05-15

Polycrystalline perovskite La{sub 0.8}Tb{sub 0.2}MnO{sub 3} (LTMO) with an orthorhombic phase was synthesized by conventional solid-state reaction. The magnetic and electric properties of La{sub 0.8}Tb{sub 0.2}MnO{sub 3} were examined. The striking finding is that the material exhibits giant magnetoresistance at room temperature as high as -31.8% and -35.7% under the low magnetic fields of 100 and 1000 Oe, respectively. This result suggests that La{sub 0.8}Tb{sub 0.2}MnO{sub 3} has a promising potential in future device developments.

La0.8Sr0.2MnO3

KAUST Repository

Wang, Q.; Chen, A. P.; Guo, E. J.; Roldan, M. A.; Jia, Q. X.; Fitzsimmons, M. R.

2018-01-01

Using polarized neutron reflectometry, we measured the influence of elastic bending stress on the magnetization depth profile of a La0.8Sr0.2MnO3 (LSMO) epitaxial film grown on a SrTiO3 substrate. The elastic bending strain of +/- 0.03% has no obvious effect on the magnetization depth profile at saturation. This result is in stark contrast to that of (La1-xPrx)(1-y),Ca-y,MnO3 (LPCMO) films for which strain of +/- 0.01% produced dramatic changes in the magnetization profile and Curie temperature. We attribute the difference between the influence of strain on the saturation magnetization in LSMO (weak or none) and LPCMO (strong) to a difference in the ability of LSMO (weak or none) and LPCMO (strong) to phase separate. Our observation provides an upper limit of tuning LSMO saturation magnetization via elastic strain effect.

Co-precipitation in aqueous medium of La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.2}O{sub 3-{delta}} via inorganic precursors

Energy Technology Data Exchange (ETDEWEB)

Pelosato, Renato; Cristiani, Cinzia; Dotelli, Giovanni; Latorrata, Saverio; Zampori, Luca [CMIC - Dipartimento di Chimica, Materiali e Ingegneria Chimica ' ' G. Natta' ' , Politecnico di Milano, P.zza Leonardo da Vinci 32, 20133 Milano (Italy); Ruffo, Riccardo [Dipartimento di Scienza dei Materiali, Universita di Milano-Bicocca, Via Cozzi 53, 20125 Milano (Italy)

2010-12-15

A simple and inexpensive co-precipitation route in aqueous medium is proposed to prepare La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 02}O{sub 3-{delta}} ionic conductor (LSGM). Different synthetic procedures and operating parameters (i.e. nature and amount of the precipitating agents, HNO{sub 3} addition and temperature) have been evaluated in order to underline their influence on the composition and microstructure of the final phase. Intermediate and final products were characterized by Thermal-Gravimetry, IR-spectroscopy, X-ray Powder Diffraction, Rietveld analysis and Scanning Electron Microscopy. The electrical properties were measured by Impedance Spectroscopy in the temperature range 250-800 C. Slight variations of the synthetic procedure (such as precipitating agent amount or no HNO{sub 3} addition) have a considerable and detrimental effect on the ions losses and the subsequent achievement of the final phase. The use NH{sub 4}OH as an alternative precipitating agent is dramatically disadvantageous. Ions losses during precipitation must be controlled (i) to avoid understoichiometry in the LSGM phase and (ii) to prevent the formation of large amounts of secondary phases. In fact, both affect the total electrical conductivity. The use of large excess of (NH{sub 4}){sub 2}CO{sub 3} precipitating agent and the addition of HNO{sub 3} lead to the best material characterized by a rhombohedral structure, small amount of side phases, a relative density of 98% and a total conductivity of 6.44 x 10{sup -2} S cm{sup -1} at 800 C and 1.13 x 10{sup -2} S cm{sup -1} at 600 C. (author)

Deactivation Studies of Rh/Ce0.8Zr0.2O2 Catalysts in Low Temperature Ethanol Steam Reforming

Energy Technology Data Exchange (ETDEWEB)

Platon, Alex; Roh, Hyun-Seog; King, David L.; Wang, Yong

2007-10-30

Rapid deactivation of Rh/Ce0.8Zr0.2O2 catalysts in low temperature ethanol steam reforming was studied. A significant build-up of carbonaceous intermediate, instead of carbon deposit, was observed at a lower reaction temperature which was attributed to the rapid catalyst deactivation. Co-feed experiments indicated that acetone and ethylene caused more severe catalyst deactivation than other oxygenates such as acidic acid and acetaldehyde.

Lattice location studies of deuterium in Pdsub(0.8)Ausub(0.2) and Ta crystals by ion channeling

International Nuclear Information System (INIS)

Takahashi, J.; Yamaguchi, S.; Koiwa, M.; Fujino, Y.; Yoshinari, O.; Hirabayashi, M.

1978-01-01

The channelling of 300 to 400 KeV deuterons combined with the D(d,p)T reaction has been used to study the lattice location of deuterium in a fcc crystal of (Pdsub(0.8)Ausub(0.2))Dsub(0.04) and a bcc crystal of TaDsub(0.10). The channelling angular distributions are measured for , , axial and brace 100 brace, brace 110 brace, brace 111 brace planar directions. It is concluded that deuterium in Pdsub(0.8)Ausub(0.2) occupies the octahedral interstice of the fcc lattice, while that in Ta occupies the tetrahedral interstice of the bcc lattice. (author)

Crystal structure of superparamagnetic Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4} nanoparticles synthesized by sol–gel method

Energy Technology Data Exchange (ETDEWEB)

Escamilla-Pérez, A.M., E-mail: angel.mep@gmail.com [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Cortés-Hernández, D.A., E-mail: dora.cortes@cinvestav.edu.mx [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Almanza-Robles, J.M. [Cinvestav-Unidad Saltillo, Industria Metalúrgica No. 1062, Parque Industrial Saltillo-Ramos Arizpe, C.P. 25900, Ramos Arizpe, Coahuila (Mexico); Mantovani, D.; Chevallier, P. [Laboratory for Biomaterials and Bioengineering, Department of Materials Engineering and University Hospital Research Center, Laval University, Quebec City, QC (Canada)

2015-01-15

Powders of magnetic iron oxide nanoparticles (Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4}) were prepared by a sol–gel method using ethylene glycol and nitrates of Fe, Ca and Mg as starting materials. Those powders were heat treated at different temperatures (573, 673, 773 and 873 K). In order to evaluate the effect of the heat treatment temperature on the nanoferrites properties, X-ray diffraction (XRD), vibrating sample magnetometry (VSM), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS) techniques were used. It was found that the reaction products exhibit nanometric sizes and superparamagnetic behavior. It is also demonstrated that, as the heat treatment temperature increases, the particle size and the saturation magnetization of the nanoferrites are increased. - Highlights: • Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4} superparamagnetic nanoparticles were successfully synthesized. • Particle average sizes of Ca–Mg ferrites were within the range of 8–25 nm. • The nanoferrite treated at 873 K showed a stoichiometry close to Mg{sub 0.2}Ca{sub 0.8}Fe{sub 2}O{sub 4}. • The heat treatment temperature has a strong effect on the crystal structure. • These nanoparticles are potential materials for magnetic hyperthermia.

Preparation and dielectric properties of Dy, Er-doped BaZr0.2Ti0.8O3 ceramics

International Nuclear Information System (INIS)

Hao Sue; Sun Liang; Huang Jinxiang

2008-01-01

Ba(Zr x Ti 1-x )O 3 nanopowders and ceramics with different Zr/Ti ratios of 1:9; 2:8; 2.5:7.5; 3.5:6.5 and 4:6 (x = 0.1, 0.2, 0.25, 0.35, 0.4) have been prepared by sol-gel technology using inorganic zirconium as raw materials, and Zr/Ti ratio of 2:8 is determined as the best one according to the measurements of dielectric properties. So the modified Ba(Zr 0.2 ,Ti 0.8 )O 3 ceramics doped by Dy and Er (the additive content is 0.10%, 0.15%, 0.20%, 0.30% and 0.50% molar ratio, respectively) have been prepared, and the effects of rare earth on the microstructure and dielectric properties of Ba(Zr 0.2 ,Ti 0.8 )O 3 ceramics have been studied. The experimental results show that the effect of Er is better than that of Dy in improving the dielectric properties of BaZr 0.2 Ti 0.8 O 3 ceramics. When the content of Er is 0.15 mol%, the dielectric constant is the highest of 12767, while the dielectric loss is lowered to 0.011; the frequency stabilities and the temperature dependence are also better, which is suitable for application in condenser field

Study on magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys

Energy Technology Data Exchange (ETDEWEB)

Tan, G.S.; Xu, H., E-mail: huixu8888@shu.edu.cn; Yu, L.Y.; Tan, X.H.; Zhang, Q.; Gu, Y.; Hou, X.L.

2017-09-01

Highlights: • (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B alloys are prepared by melt-spinning method with simultaneously decreasing of Nd, Ce concentration. • The magnetic properties B{sub r}, (BH){sub max} and squareness are all improved with an appropriate reduction of Nd, Ce concentration. • Magnetic field heat treatment offers a significant improvement in B{sub r}, (BH){sub max} and squareness. - Abstract: In the present work, (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) permanent alloys are prepared by melt-spinning method. The hard magnetic properties of (Nd{sub 0.8}Ce{sub 0.2}){sub 2−x}Fe{sub 12}Co{sub 2}B (x = 0–0.6) alloys annealed at optimum temperatures have been investigated systematically. Depending on the Nd, Ce concentration, the maximum energy product ((BH){sub max}) and remanence (B{sub r}) increase gradually with x in the range of 0 ≤ x ≤ 0.4, whereas decrease gradually in the alloys with 0.4 < x ≤ 0.6. It is found that the optimum magnetic properties are obtained at x = 0.4: H{sub ci} = 4.9 kOe, B{sub r} = 10.1 kG, (BH){sub max} = 13.7 MGOe. Specifically, magnetic field heat treatment below the Curie temperature is applied for (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B (x = 0.4) annealed ribbons. The magnetic properties B{sub r}, (BH){sub max} and squareness are all enhanced after the magnetic field heat treatment. The (BH){sub max} shows a substantial increase from 13.7 MGOe to 16.0 MGOe after the heat treatment at 623 K with a magnetic field of 1 T, which gets 17% improvement compared with that of the sample without a magnetic field heat treatment. We demonstrate that the magnetic field heat treatment plays a certain role in the magnetization reversal behavior and can improve the microstructure of (Nd{sub 0.8}Ce{sub 0.2}){sub 1.6}Fe{sub 12}Co{sub 2}B alloy.

Characterization of Laboratory Prepared Concrete Pastes Exposed to High Alkaline and High Sodium Salt Solutions

Energy Technology Data Exchange (ETDEWEB)

Langton, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-06-30

The objective of this study was to identify potential chemical degradation mechanisms for the Saltstone Disposal Unit (SDU) concretes, which over the performance life of the structures may be exposed to highly alkaline sodium salt solutions containing sulfate, hydroxide, and other potentially corrosive chemicals in salt solution and saltstone flush water, drain water, leachate and / or pore solution. The samples analyzed in this study were cement pastes prepared in the SIMCO Technologies, Inc. concrete laboratory. They were based on the paste fractions of the concretes used to construct the Saltstone Disposal Units (SDUs). SDU 1 and 4 concrete pastes were represented by the PV1 test specimens. The paste in the SDU 2, 3, 5, and 6 concrete was represented by the PV2 test specimens. SIMCO Technologies, Inc. selected the chemicals and proportions in the aggressive solutions to approximate proportions in the saltstone pore solution [2, 3, 5, and 6]. These test specimens were cured for 56 days in curing chamber before being immersed in aggressive solutions. After exposure, the samples were frozen to prevent additional chemical transport and reaction. Selected archived (retrieved from the freezer) samples were sent to the Savannah River National Laboratory (SRNL) for additional characterization using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray (EDX) spectroscopy. Characterization results are summarized in this report. In addition, a correlation between the oxide composition of the pastes and their chemical durability in the alkaline salt solutions is provided.

In situ X-ray and neutron diffraction of the Ruddlesden-Popper compounds (RE2-xSrx)0.98(Fe0.8Co0.2)1-yMgyO4-δ (RE=La, Pr): Structure and CO2 stability

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Hauback, B.C.; Hendriksen, Peter Vang

2013-01-01

The crystal structure of the Ruddlesden-Popper compounds (La 1.0Sr1.0)0.98Fe0.8Co 0.2O4-δ and (La1.2Sr0.8) 0.98(Fe0.8Co0.2)0.8Mg 0.2O4-δ was investigated at 1000 °C in N 2 (aO2=1×10-4) by in-situ powder neutron diffraction. In-situ powder X-ray diffraction (PXD) was also employed to investigate....... The equivalent pseudo-cubic thermal and chemical expansion coefficients are in agreement with values determined by dilatometry. The chemical stability in CO2 containing environments of various Ruddlesden-Popper compounds with chemical formula (RE2-xSr x)0.98(Fe0.8Co0.2) 1-yMgyO4-δ (RE=La, Pr), as well...

Electrochemical synthesis of nanoplatelets-like CuS0.2Se0.8 thin film for photoluminescence applications

Directory of Open Access Journals (Sweden)

Sharma A. K.

2015-06-01

Full Text Available Copper sulfide-selenide (CuS0.2Se0.8 thin films were deposited on FTO coated glass substrate (fluorine doped tin oxide and stainless steel substrates using electrodeposition technique. Deposited thin films were characterized using different characterization techniques viz. X-ray diffraction (XRD, scanning electron microscopy (SEM, UV-Vis spectroscopy, photoluminescence spectroscopy and surface wettability. XRD study showed polycrystalline nature with cubic phase of the films. Scanning electron microscopy showed that the surface area of the substrate was covered by the nanoplatelets structure of a thickness of 140 to 150 nm and optical study showed that the direct band gap was ~1.90 eV. Surface wettability showed hydrophobic nature of the CuS0.2Se0.8 thin films.

Corrosion resistance of welded joints in 08Kh22N6T and 08Kh21N6M2T steels made with new electrodes

International Nuclear Information System (INIS)

Sidorkina, Y.S.; Leibzon, V.M.; Mankevich, T.V.; Sidlin, E.A.; Zheltova, G.A.

1986-01-01

This paper examines the corrosion resistance of 08Kh22N6T and 08Kh21N6M2T steels which would make it possible to ensure equal properties of all the zones of the welded joints. The investigations were carried out on the welded joints in the steels produced with new OZL-40 and OZL-41 electrodes and with standard TsL-11 and EA-400/10u electrodes. The chemical compositions of the steels and deposited metal are presented. The tests of the intercrystalline corrosion resistances of the welded joints in the steels in the as-welded condition and after heat treatment showed that the weld metal is not attacked by intercrystalline corrosion. The tests also showed that the welded joints in 08Kh22N6T steel made with the OZL-40 and TsL-11 electrodes are resistant to corrosion in 55% phosphoric acid at 90 C in 1% sulfuric acid, and in 25% formic acid at 80 C. The investigated steels made with the OZL-40 and OZL-41 electrode respectively show that the welded joints are resistant to intercrystalline and general corrosion, have high mechanical and processing properties and the electrodes, and can be used for welding equipment designed for service in alkaline, neutral, and slightly acid media

Literature review of the potential impact of glycolic acid on the technetium chemistry of srs tank waste

International Nuclear Information System (INIS)

Nash, Charles A.; McCabe, Daniel J.

2017-01-01

This document presents a literature study of the impact of glycolate on technetium chemistry in the Savannah River Site (SRS) waste system and specifically Saltstone. A predominant portion of the Tc at SRS will be sent to the Saltstone Facility where it will be immobilized. The Tc in the tank waste is in the highly soluble chemical form of pertechnetate ion (TcO 4 - ) which is reduced by blast furnace slag (BFS) in Saltstone, rendering it highly insoluble and resistant to leaching.

PDB: CBRC-PABE-08-0030 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-PABE-08-0030 1U34,2JNC,2JND, Region:45-139(Identity=85%) PDB:1U34 Chain:A (NMR),Region:45-139(Identity...=85%) PDB:2JNC Chain:A (NMR),Region:45-139(Identity=85%) PDB:2JND Chain:A (NMR), ...

Quantum control for initiation and detection of explosives

International Nuclear Information System (INIS)

Greenfield, Margo T.; McGrane, Shawn D.; Scharff, R. Jason; Moore, David S.

2010-01-01

We employ quantum control methods towards detection and quantum controlled initiation (QCI) of energetic materials. Ultrafast pulse shaping of broadband Infrared (∼750 nm to 850 run) and ultraviolet (266 nm, 400 nm) light is utilized for control. The underlying principals behind optimal control can be utilized to both detect and initiate explosives. In each case, time dependent phase shaped electric fields drive the chemical systems towards a desired state. For optimal dynamic detection of explosives (ODD-Ex) a phase specific broadband infrared pulse is created which increases not only the sensitivity of detection but also the selectivity of an explosive's spectral signatures in a background of interferents. QCI on the other hand, seeks to initiate explosives by employing shaped ultraviolet light. QCI is ideal for use with explosive detonators as it removes the possibility of unintentional initiation from an electrical source while adding an additional safety feature, initiation only with the proper pulse shape. Quantum control experiments require: (1) the ability to phase and amplitude shape the laser pulse and (2) the ability to effectively search for the pulse shape which controls the reaction. In these adaptive experiments we utilize both global and local optimization search routines such as genetic algorithm, differential evolution, and downhill simplex. Pulse shaping the broadband IR light, produced by focusing 800 nm light through a pressurized tube of Argon, is straightforward as commercial pulse shapers are available at and around 800 nm. Pulse shaping in the UV requires a home built shaper. Our system is an acoustic optical modulator (AOM) pulse shaper in which consists of a fused silica AOM crystal placed in the Fourier plane of a 4-f zero dispersion compressor.

Literature review of the potential impact of glycolic acid on the technetium chemistry of srs tank waste

Energy Technology Data Exchange (ETDEWEB)

Nash, Charles A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, Daniel J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-10-09

This document presents a literature study of the impact of glycolate on technetium chemistry in the Savannah River Site (SRS) waste system and specifically Saltstone. A predominant portion of the Tc at SRS will be sent to the Saltstone Facility where it will be immobilized. The Tc in the tank waste is in the highly soluble chemical form of pertechnetate ion (TcO₄ ^-) which is reduced by blast furnace slag (BFS) in Saltstone, rendering it highly insoluble and resistant to leaching.

Validation of ASTECV2.1 based on the QUENCH-08 experiment

Energy Technology Data Exchange (ETDEWEB)

Gómez-García-Toraño, Ignacio, E-mail: ignacio.torano@kit.edu [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology (INR), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Sánchez-Espinoza, Víctor-Hugo; Stieglitz, Robert [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology (INR), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Stuckert, Juri [Karlsruhe Institute of Technology, Institute for Applied Materials-Applied Materials Physics (IAM-AWP), Hermann-von-Helmholtz-Platz 1, D-76344 Eggenstein-Leopoldshafen (Germany); Laborde, Laurent; Belon, Sébastien [Institut de Radioprotection et de Sûreté Nucléaire (IRSN), Nuclear Safety Division/Safety Research/Severe Accident Department, Saint Paul Lez Durance 13115 (France)

2017-04-01

Highlights: • ASTECV2.1 can reproduce QUENCH-08 experimental trends e.g. hydrogen generation. • Radial temperature gradient and heat transfer through argon gap are underestimated. • Mesh sizes lower than 55 mm needed to capture the strong axial temperature gradient. • Minor variations of external electrical resistance strongly affect bundle heat-up. • Modelling of a bypass and inclusion of currents partially overcome discrepancies. - Abstract: The Fukushima accidents have shown that further improvements of Severe Accident Management Guidelines (SAMGs) are still necessary. Hence, the enhancement of severe accident codes and their validation based on integral experiments is pursued worldwide. In particular, the capabilities of the European integral severe accident ASTECV2.1 code are being extended within the CESAM project through the improvement of physical models, code numerics and an extensive code validation. Among the different strategies encompassed in the plant SAMGs, one of the most important ones to prevent core damage is the injection of water into the overheated core (reflooding). However, under certain conditions, reflooding may trigger a sharp hydrogen generation that may jeopardize the containment. Within this work, ASTECV2.1 models describing the early in-vessel phase of the severe accident and its termination by core reflooding are validated against data from the QUENCH test facility. The QUENCH-08, involving the injection of 15 g/s (about 0.6 g/s/rod) of saturated steam at a bundle temperature of 2073 K, has been selected for this comparison. Results show that ASTECV2.1 is able to reproduce the experimental temperatures and oxide thicknesses at representative bundle locations. The predicted total hydrogen generation (76 g) is similar to the experimental one (84 g). In addition, the choices of an axial mesh size lower than 55 mm and of an external electrical resistance of a 7 mΩ/rod have been justified with parametric analyses. Finally, new

NCBI nr-aa BLAST: CBRC-DSIM-08-0053 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DSIM-08-0053 ref|ZP_01915505.1| hypothetical protein LMED105_09745 [Limnobacter... sp. MED105] gb|EDM83186.1| hypothetical protein LMED105_09745 [Limnobacter sp. MED105] ZP_01915505.1 2e-08 32% ...

Results for the second quarter 2014 tank 50 WAC slurry sample chemical and radionuclide contaminants

International Nuclear Information System (INIS)

Bannochie, C.

2014-01-01

This report details the chemical and radionuclide contaminant results for the characterization of the 2014 Second Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by DWPF & Saltstone Facility Engineering (DSFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System

Results for the Third Quarter 2014 Tank 50 WAC slurry sample: Chemical and radionuclide contaminants

Energy Technology Data Exchange (ETDEWEB)

Crawford, Charles L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-01-08

This report details the chemical and radionuclide contaminant results for the characterization of the 2014 Third Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time.¹ Information from this characterization will be used by DWPF & Saltstone Facility Engineering (DSFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System.

Results For The Fourth Quarter 2014 Tank 50 WAC Slurry Sample: Chemical And Radionuclide Contaminants

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-09-30

This report details the chemical and radionuclide contaminant results for the characterization of the Calendar Year (CY) 2014 Fourth Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by DWPF & Saltstone Facility Engineering (DSFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System.

Results For The Third Quarter 2013 Tank 50 WAC Slurry Sample

Energy Technology Data Exchange (ETDEWEB)

Bannochie, Christopher J.

2013-11-26

This report details the chemical and radionuclide contaminant results for the characterization of the 2013 Third Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by DWPF & Saltstone Facility Engineering (DSFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System.

Results For The Second Quarter 2013 Tank 50 WAC Slurry Sample: Chemical And Radionuclide Contaminants

Energy Technology Data Exchange (ETDEWEB)

Bannochie, Christopher J.

2013-07-31

This report details the chemical and radionuclide contaminant results for the characterization of the 2013 Second Quarter sampling of Tank 50 for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by Saltstone Facility Engineering (SFE) to support the transfer of low-level aqueous waste from Tank 50 to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50 Waste Characterization System.

Magnetisation and AC susceptibility studies of La1-xSrxFe0.8Cr0.2O3-δ (0.0

International Nuclear Information System (INIS)

Ferreira, L.P.; Cruz, M.M.; Ramos, T.; Sa, M.A.; Carvalho, M.D.; Godinho, M.

2007-01-01

Magnetisation and AC magnetic susceptibility measurements have been performed in the perovskite-type compounds La 1-x Sr x Fe 0.8 Cr 0.2 O 3-δ (x=0.2, 0.4, 0.6 and 0.8). All compounds show an overall antiferromagnetic behaviour mainly attributed to predominant Fe 3+ -O-Fe 3+ interactions. For 0.2 ord . The coexistence of AFM and FM interactions leads to reentrant magnetic behaviour for the x=0.4 compound and to spin-glass like behaviour for x=0.8. Between x=0.6 and 0.8, the similar magnetic moments found in the paramagnetic region indicate that the Fe/Cr valences do not change significantly, pointing towards an increased role for oxygen vacancy formation in the charge compensation mechanism

Growth of solid solutions with colquiriite structure LiCa0,2Sr0,8AlF6: Ce3+

International Nuclear Information System (INIS)

Shavelev, A A; Nizamutdinov, A S; Semashko, V V; Marisov, M A

2014-01-01

Aim of this work were experiments on growing new materials based on fluoride crystals with the colquiriite structure LiSr 0,8 Ca 0,2 F 6 , as well as the study of their phase composition. It is shown that for a series of crystals LiSr 0,8 Ca 0,2 F 6 distribution of reflections observed corresponds to the colquiriite structure, and the dependence of the lattice constant in the transition from LiCaAlF 6 crystal to LiSrAlF 6 crystal is linear. Also it found that absorption coefficient in mixed samples is much larger than in not mixed

Magnetocaloric effect in the La0.8Ce0.2Fe11.4-xCoxSi1.6 compounds

International Nuclear Information System (INIS)

Wang, G.F.; Song, L.; Li, F.A.; Ou, Z.Q.; Tegus, O.; Brueck, E.; Buschow, K.H.J.

2009-01-01

The effects of substitution of Co for Fe on the magnetic and magnetocaloric properties of La 0.8 Ce 0.2 Fe 11.4-x Co x Si 1.6 (0, 0.2, 0.4, 0.6, 0.8 and 1.0) compounds have been investigated. X-ray diffraction shows that all compounds crystallize in the NaZn 13 -type structure. Magnetic measurements show that the Curie temperature (T C ) can be tuned between 184 and 294 K by changing the Co content from 0 to 1. A field-induced methamagnetic transition occurs in samples with x=0, 0.2 and 0.4. The magnetic entropy changes of the compounds have been determined from the isothermal magnetization measurements by using the Maxwell relation.

Resistance switching mechanism of La{sub 0.8}Sr{sub 0.2}MnO{sub 3−δ} thin films

Energy Technology Data Exchange (ETDEWEB)

Luo, X.D. [School of Metallurgy and Materials Engineering, Chongqing University of Science and Technology, Chongqing 401331 (China); Chongqing Key Laboratory of Nano/Micro Composite Materials and Devices, Chongqing 401331 (China); Gao, R.L., E-mail: gaorongli2008@163.com [School of Metallurgy and Materials Engineering, Chongqing University of Science and Technology, Chongqing 401331 (China); Chongqing Key Laboratory of Nano/Micro Composite Materials and Devices, Chongqing 401331 (China); Fu, C.L.; Cai, W.; Chen, G.; Deng, X.L. [School of Metallurgy and Materials Engineering, Chongqing University of Science and Technology, Chongqing 401331 (China); Chongqing Key Laboratory of Nano/Micro Composite Materials and Devices, Chongqing 401331 (China); Zhang, H.R; Sun, J.R. [Beijing National Laboratory for Condensed Matter Physics and Institute of Physics, Chinese Academy of Science, Beijing 100190 (China)

2016-02-15

Effects of oxygen vacancies on the electrical transport properties of oxygen stoichiometric La{sub 0.8}Sr{sub 0.2}MnO{sub 3} and oxygen-deficient La{sub 0.8}Sr{sub 0.2}MnO{sub 3−δ} films have been investigated. The result presents that the oxygen-deficient films annealed in vacuum show obvious increase of resistance and lattice parameter. With the sweeping voltage or temperature increasing, the resistance exhibits obvious bipolar switching effect, no forming process was needed. Oxygen deficiency in the annealed film leads to the formation of a structural disorder in the Mn–O–Mn conduction channel due to the accumulation of oxygen vacancies under high external electric field or temperatures and hence is believed to be responsible for the bipolar resistance switching effect and the enhanced resistivity compared with oxygen stoichiometric La{sub 0.8}Sr{sub 0.2}MnO{sub 3} film. These results may be important for practical applications in photoelectric or storage devices and point to a useful direction for other oxidizing materials.

Vortex phase diagram for extremely underdoped Bi2.2Sr1.72La0.08CaCu2O8+δ

International Nuclear Information System (INIS)

Yamaguchi, Yuij; Oka, Kunihiko; Mumtaz, Arif; Bando, Hiroshi

2003-01-01

Vortex phase diagram for H parallel c of extremely underdoped Bi 2.2 Sr 1.72 La 0.08 CaCu 2 O 8+δ superconductor was determined from a magnetization measurement. In the magnetization curve, a second peak in the low temperature region and a sharp change in the high temperature region were observed. The second-peak field and the sharp-change field are explained based on the three-to-two dimensional crossover and the decoupling transition of the vortex lattice, respectively. For the most underdoped sample, which has the transition temperature T c =60.2 K, the anisotropy constant γ and the ab plane penetration length λ 0 have been deduced to be γ=320 and λ 0 ∼340 nm, respectively

High performance Sm{sub 0.5}Sr{sub 0.5}CoO{sub 3}-La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.15}Co{sub 0.05}O{sub 3} composite cathodes

Energy Technology Data Exchange (ETDEWEB)

Wang, Shizhong; Zou, Yuman [College of Chemistry and Chemical Engineering, Department of Chemistry, Xiamen University, Xiamen 361005, Fujian (China)

2006-06-15

High performance Sm{sub 0.5}Sr{sub 0.5}CoO{sub 3}(SSC)-La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.15}Co{sub 0.05}O{sub 3} (LSGMC5) composite cathodes for intermediate temperature solid oxide fuel cells (ITSOFC) were prepared and characterized. The SSC powders were synthesized using the glycine-nitrate method and La{sub 0.8}Sr{sub 0.2}Ga{sub 0.8}Mg{sub 0.15}Co{sub 0.05}O{sub 3}(LSGMC5) powders were synthesized using the citrate method. The calcining temperature for the SSC and LSGMC5 powders had strong effect on the microstructure of the composite electrode and electrode/electrolyte interface, which affected the performance of the SSC-LSGMC5 electrode strongly. The electrode based on SSC calcined at 1223K and LSGMC5 calcined at 1273K exhibited the highest performance among the electrodes studied. The electrode resistance was about 0.07{omega}cm{sup 2}, and the overpotential under 1Acm{sup -2} current density was as low as 0.077V at 973K in oxygen, which could be an ideal cathode for ITSOFC based on lanthanum gallate electrolytes. (author)

Measurement of the factor of dispersion in air for a field of 0,8* 8,0 CM 2

International Nuclear Information System (INIS)

Gomez-Tejedor Alonso, S.; Huertas Martinez, C.; Penedo Cobos, J. M.; Garcia Castejon, M. A.; Rincon Perezx, M.

2013-01-01

The measures of this factor of dispersion in air is usually performed with an ionization chamber cover a cap of balance of such thickness that is achieved the electronic balance, and must be covered completely the CAP by the radiation field. This procedure is not applicable for small fields. The need to measure the Sc of a field of 0.8 * 0.8 cm 2 for a new system of planning led us to try another measure procedure proposed in the literature, using detectors of semiconductor with a sheet of cerrobend by way of balance Cap. (Author)

Absorption spectra between 0.8 {mu} and 30 {mu} of mixtures of H{sub 2}O - D{sub 2}O in the liquid state; Le spectre d'absorption des melanges H{sub 2}O-D{sub 2}O a l'etat liquide entre 0,8 et 30 {mu}

Energy Technology Data Exchange (ETDEWEB)

Ceccaldi, M; Goldman, M; Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

There has been very little work carried out recently on the absorption bands of H{sub 2}O, HDO and D{sub 2}O in the liquid state. We have established the spectra of these molecules in between 0.8 and 30 p. The table of absorption bands of the molecules HDO and D{sub 2}O for which all the bands corresponding to those for H{sub 2}O had not been established has been completed. We have sought a convenient method of representing the variations in optical density of certain HDO bands as a function of the concentration of heavy water in the mixtures studied. (author) [French] Il y a peu de travaux recents sur les bandes d'absorption de H{sub 2}O, HDO et D{sub 2}O a l'etat liquide. Nous avons releve les spectres de ces molecules entre 0,8 et 30 p. Le tableau des bandes d'absorption des molecules HDO et D{sub 2}O, pour lesquelles le releve de toutes les bandes correspondantes a celles de H{sub 2}O n'etait pas encore effectue, a ete complete. Nous avons cherche des modes de representation commodes des variations de densite optique de certaines bandes de HDO en fonction de la teneur en eau lourde des melanges etudies. (auteur)

Ferroelectric switching in epitaxial PbZr0.2Ti0.8O3/ZnO/GaN heterostructures

Science.gov (United States)

Wang, Juan; Salev, Pavel; Grigoriev, Alexei

As a wide-bandgap semiconductor, ZnO has gained substantial interest due to its favorable properties including high electron mobility, strong room-temperature luminescence, etc. The main obstacle of its application is the lack of reproducible and low-resistivity p-type ZnO. P-type doping of ZnO through the interface charge injection, which can be achieved by the polarization switching of ferroelectric films, is a tempting solution. We explored ferroelectric switching behavior of PbZr0.2Ti0.8O3/ZnO/GaN heterostructures epitaxially grown on Sapphire substrates by RF sputtering. The electrical measurements of Pt/PbZr0.2Ti0.8O3/ZnO/GaN ferroelectric-semiconductor capacitors revealed unusual behavior that is a combination of polarization switching and a diode I-V characteristics.

Neutron-diffraction study of the crystal structure of the superconductor TiSr2(Eu0.8Ce0.2)2Cu2Oz

International Nuclear Information System (INIS)

Ishigaki, T.; Ogasawara, Y.; Oikawa, K.; Hoshikawa, A.; Kamiyama, T.

2004-01-01

TiSr 2 (RE 1-x Ce x ) 2 Cu 2 O z superconductors (T c ∼20 K) have a 1222-structure with fluorite blocks. Neutron diffraction has been performed on the Eu-containing compound TiSr 2 (Eu 0.8 Ce 0.2 ) 2 Cu 2 O z , with natural Eu, and its crystal structure was refined. The neutron powder diffraction experiment was carried out on the VEGA diffractometer at KENS. The sample was contained in a thin flat cell of 0.5 mm thickness in order to reduce the large absorption effects of natural Eu. The absorption correction for the flat sample was taken into account in the Rietveld refinement. The results show that the O(1) atom in the Ti-layer is shifted from the 4c-site to the split site (8j), and that the concentration is deficient (g∼0.19)

Experimental determination of the Onsager coefficients of transport for Ce0.8Pr0.2O2−δ

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Park, Woo-Seok; Kim, Hong-Seok

2010-01-01

versa for the flux of electrons (Je). It is common practice to assume that electrons and mobile ions migrate independently, despite the lack of experimental evidence in support of this. Here, all the Onsager coefficients, including the cross coefficients, have been measured for Ce0.8Pr0.2O2−δ within...... the aO2 range 10−21–1 at 800 °C, using local ionic and electronic probes in a four-probe configuration. The cross coefficients of transport were found to be negligible in comparison to the direct coefficients in the aO2 range 10−21–10−4, but of the same order of magnitude as the direct coefficients...

Results for the Fourth Quarter Calendar Year 2015 Tank 50H Salt Solution Sample

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-01-11

In this memorandum, the chemical and radionuclide contaminant results from the Fourth Quarter Calendar Year 2015 (CY15) sample of Tank 50H salt solution are presented in tabulated form. The Fourth Quarter CY15 Tank 50H samples were obtained on October 29, 2015 and received at Savannah River National Laboratory (SRNL) on October 30, 2015. The information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering for the transfer of aqueous waste from Tank 50H to the Salt Feed Tank in the Saltstone Production Facility, where the waste will be treated and disposed of in the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the Task Technical and Quality Assurance Plan (TTQAP) for the Tank 50H saltstone task. The chemical and radionuclide contaminant results from the characterization of the Fourth Quarter Calendar Year 2015 (CY15) sampling of Tank 50H were requested by SRR personnel and details of the testing are presented in the SRNL Task Technical and Quality Assurance Plan.

Giant strain with low cycling degradation in Ta-doped [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} lead-free ceramics

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiaoming; Tan, Xiaoli, E-mail: xtan@iastate.edu [Department of Materials Science and Engineering, Iowa State University, Ames, Iowa 50011 (United States)

2016-07-21

Non-textured polycrystalline [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}](Ti{sub 1−x}Ta{sub x})O{sub 3} ceramics are fabricated and their microstructures and electrical properties are characterized. Transmission electron microscopy reveals the coexistence of the rhombohedral R3c and tetragonal P4bm phases in the form of nanometer-sized domains in [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} with low Ta concentration. When the composition is x = 0.015, the electrostrain is found to be highly asymmetric under bipolar fields of ±50 kV/cm. A very large value of 0.62% is observed in this ceramic, corresponding to a large-signal piezoelectric coefficient d{sub 33}* of 1240 pm/V (1120 pm/V under unipolar loading). These values are greater than most previously reported lead-free polycrystalline ceramics and can even be compared with some lead-free piezoelectric single crystals. Additionally, this ceramic displays low cycling degradation; its electrostrain remains above 0.55% even after undergoing 10 000 cycles of ±50 kV/cm bipolar fields at 2 Hz. Therefore, Ta-doped [Bi{sub 1/2}(Na{sub 0.8}K{sub 0.2}){sub 1/2}]TiO{sub 3} ceramics show great potential for large displacement devices.

Impact of natural and calcined starfish (Asterina pectinifera) on the stabilization of Pb, Zn and As in contaminated agricultural soil.

Science.gov (United States)

Lim, Jung Eun; Sung, Jwa Kyung; Sarkar, Binoy; Wang, Hailong; Hashimoto, Yohey; Tsang, Daniel C W; Ok, Yong Sik

2017-04-01

Metal stabilization using soil amendments is an extensively applied, economically viable and environmentally friendly remediation technique. The stabilization of Pb, Zn and As in contaminated soils was evaluated using natural starfish (NSF) and calcined starfish (CSF) wastes at different application rates (0, 2.5, 5.0 and 10.0 wt%). An incubation study was conducted over 14 months, and the efficiency of stabilization for Pb, Zn and As in soil was evaluated by the toxicity characteristic leaching procedure (TCLP) test. The TCLP-extractable Pb was reduced by 76.3-100 and 91.2-100 % in soil treated with NSF and CSF, respectively. The TCLP-extractable Zn was also reduced by 89.8-100 and 93.2-100 % in soil treated with NSF and CSF, respectively. These reductions could be associated with the increased metal adsorption and the formation of insoluble metal precipitates due to increased soil pH following application of the amendments. However, the TCLP-extractable As was increased in the soil treated with NSF, possibly due to the competitive adsorption of phosphorous. In contrast, the TCLP-extractable As in the 10 % CSF treatment was not detectable because insoluble Ca-As compounds might be formed at high pH values. Thermodynamic modeling by visual MINTEQ predicted the formation of ettringite (Ca 6 Al 2 (SO 4 ) 3 (OH) 12 ·26H 2 O) and portlandite (Ca(OH) 2 ) in the 10 % CSF-treated soil, while SEM-EDS analysis confirmed the needle-like structure of ettringite in which Pb was incorporated and stabilized in the 10 % CSF treatment.

Scholarly productivity and professional advancement of junior researchers receiving KL2, K23, or K08 awards at a large public research institution.

Science.gov (United States)

Amory, John K; Louden, Diana K N; McKinney, Christy; Rich, Joanne; Long-Genovese, Stacy; Disis, Mary L

2017-04-01

How the productivity and careers of KL2 scholars compare with scholars receiving individual K-awards is unknown. The productivity of KL2 scholars (n=21) at our institution was compared with that of K08 (n=34) and K23 (n=26) scholars. KL2 and K23 scholars had greater productivity than K08 scholars ( p =0.01). Professional advancement was similar among groups. At our institution, scholarly productivity and professional advancement did not differ by type of K-award.

17 CFR 8.08 - Disciplinary committee.

Science.gov (United States)

2010-04-01

... 17 Commodity and Securities Exchanges 1 2010-04-01 2010-04-01 false Disciplinary committee. 8.08 Section 8.08 Commodity and Securities Exchanges COMMODITY FUTURES TRADING COMMISSION EXCHANGE PROCEDURES FOR DISCIPLINARY, SUMMARY, AND MEMBERSHIP DENIAL ACTIONS Disciplinary Procedure § 8.08 Disciplinary...

SSR marker analysis on genetic variation of M3 from maize inbred lines 48-2 and R08 after irradiation inducement

International Nuclear Information System (INIS)

Li Qi; Shi Haichun; Ke Yongpei; Yuan Jichao; Yu Xuejie

2011-01-01

Analyzing the biological effects and the genetic variations of maize mutagenic progenies is important to facilitate effective selections and utilization of the mutants. In this study, the genetic variation of 103 mutagenic progenies of M 3 lines of inbred lines 48-2 and R08 with 60 Co γ-rays inducement were evaluated with SSR molecular markers. The results indicated that, the amplitude of polymorphism information content (PIC) of the 48-2 and R08 M 3 lines ranged 0.307 ∼ 0.948 and 0.108 ∼ 0.955, with an average of 0.762 and 0.701, respectively. The amplitude of genetic diversity indexes (H') ranged 0.552 ∼ 2.830 and 0.254 ∼ 3.309, with an average of 1.830 and 1.777, respectively. The average value of genetic similarity coefficient of the 49 M 3 lines of 48-2 with its check (M673) was 0.8194. However, the average value of genetic similarity coefficient of the M 3 lines of R08 with its check (M487) was 0.8373. Based on the genetic similarity coefficient, inbred lines 48-2, R08 and their 101 M 3 lines were clustered in 7 and 5 populations respectively. This phenomenon indicated that massive genetic variation could appear in progenies due to irradiation. The strengthen of selection and utilization of mutants based on the breeding objectives and in accordance with the feature and regularity on genetic variations of main characteristics of mutant lines in various populations could be enhanced in breeding program, to some extent, which can increase the breeding efficiency of irradiation induced mutation in maize. (authors)

Disposal of decontaminated salts at the Savannah River Plant by solidification and burial

International Nuclear Information System (INIS)

Dukes, M.D.; Wolf, H.C.; Langton, C.A.

1983-01-01

The current plan for disposal of waste salt at the Savannah River Plant (SRP) is to immobilize the decontaminated salt solution by mixing with cement and SRP soil, and bury the resulting grout (saltstone) in a landfill. The grout which contains 37.8 wt % salt solution, 22.8 wt % Portland I-P cement, and 39.2 wt % SRP soil, was specially formulated to have a low permeability ( -10 cm/sec). This material will be mixed and placed in trenches. After setting, the saltstone will be covered with a clay cap, and an overburden of compacted native soil will be replaced. 6 references

Band alignment of atomic layer deposited MgO/Zn0.8Al0.2O heterointerface determined by charge corrected X-ray photoelectron spectroscopy

Science.gov (United States)

Yan, Baojun; Liu, Shulin; Yang, Yuzhen; Heng, Yuekun

2016-05-01

Pure magnesium (MgO) and zinc oxide doped with aluminum oxide (Zn0.8Al0.2O) were prepared via atomic layer deposition. We have studied the structure and band gap of bulk Zn0.8Al0.2O material by X-ray diffractometer (XRD) and Tauc method, and the band offsets and alignment of atomic layer deposited MgO/Zn0.8Al0.2O heterointerface were investigated systematically using X-ray photoelectron spectroscopy (XPS) in this study. Different methodologies, such as neutralizing electron gun, the use of C 1s peak recalibration and zero charging method, were applied to recover the actual position of the core levels in insulator materials which were easily influenced by differential charging phenomena. Schematic band alignment diagram, valence band offset (ΔEV) and conduction band offset (ΔEC) for the interface of the MgO/Zn0.8Al0.2O heterostructure have been constructed. An accurate value of ΔEV = 0.72 ± 0.11 eV was obtained from various combinations of core levels of heterojunction with varied MgO thickness. Given the experimental band gaps of 7.83 eV for MgO and 5.29 eV for Zn0.8Al0.2O, a type-II heterojunction with a ΔEC of 3.26 ± 0.11 eV was found. Band offsets and alignment studies of these heterojunctions are important for gaining deep consideration to the design of various optoelectronic devices based on such heterointerface.

Composite Ag-La0.8Sr0.2MnO3-σ Cathode for Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Mosiałek M.

2013-12-01

Full Text Available Na powierzchni elektrolitu stałego wytwarzano kompozytowe katody dla stałotlenkowych ogniw paliwowych zbudowane z metalicznego srebra rozproszonego w osnowie z La0.8Sr0,3MnO3-σ Osnowę o kontrolowanej porowatości otrzymywano przez prażenie mieszaniny proszku La0.8Sr0.2MnO3-σ z kulkami z tworzywa organicznego. Porowatą osnowę nasycano roztworem AgNCb i ponownie wyprażano. Tak otrzymane katody wykazywały wyższą przewodność elektryczną i niższą oporność akty- wacyjną w reakcji redukcji tlenu w porównaniu z katodami z czystej ceramiki.

Characterization of particulate sol-gel synthesis of LiNi0.8Co0.2O2 via maleic acid assistance with different solvents

International Nuclear Information System (INIS)

Zhong, Y.D.; Zhao, X.B.; Cao, G.S.; Tu, J.P.; Zhu, T.J.

2006-01-01

Particulate sol-gel LiNi 0.8 Co 0.2 O 2 has been synthesized by a maleic-acid-assisted process using de-ionized water or ethanol as the solvent. A comparison of the effect on these two different solvents was made on the basis of thermal studies, Fourier transform infrared spectroscopy, X-ray diffraction analysis, chemical diffusion coefficients measurement, and electrochemical cyclability tests. An esterification reaction occurred on the xerogel prepared with ethanol as solvent, reducing Ni and Co from their nitrate salts. LiNi 0.8 Co 0.2 O 2 grew at the expense of Li 2 CO 3 , NiO, and CoO during calcination. Better results of capacity and cyclability were obtained in a DI-water-solvent sample associated with a larger interslab thickness between O-Li-O and lower Ni occupancy on the Li site. The activation energy for the calcinations of DI-water-solvent sample is one-half of that of the ethanol-solvent one, which could be the reason for its better properties. Chemical diffusion coefficients of Li + ion are of the same order 10 -10 cm 2 /s, is not affected by the solvents used and/or the temperature raise to 55 deg. C

Synthesis of LiNi0.8Co0.1Mn0.1O2 cathode material by chloride co-precipitation method

Institute of Scientific and Technical Information of China (English)

李灵均; 李新海; 王志兴; 伍凌; 郑俊超; 李金辉

2010-01-01

LiNi0.8Co0.1Mn0.1O2 was prepared by a chloride co-precipitation method and characterized by thermogravimetric analysis, X-ray diffractometry with Rietveld refinement,electron scanning microscopy and electrochemical measurements.Effects of lithium ion content and sintering temperature on physical and electrochemical performance of LiNi0.8Co0.1Mn0.1O2 were also investigated. The results show that the sample synthesized at 750℃with 105%lithium content has fine particle sizes around 200 nm and homogenous sizes distribution.The initial discharge capacity for the powder is 184 mA·h/g between 2.7 and 4.3 V at 0.1C and room temperature.

Phase transition and conduction mechanism in Pb{sub 2}Na{sub 0.8}R{sub 0.2}Nb{sub 4.8}Fe{sub 0.2}O{sub 15} material (R=rare earth)

Energy Technology Data Exchange (ETDEWEB)

Bouziane, M. [Laboratoire de Chimie du Solide Appliquée, Faculté des Sciences, Université Mohammed V-Agdal, Avenue Ibn Batouta, BP 1014 Rabat (Morocco); Taibi, M., E-mail: taibiens@yahoo.fr [Laboratoire de Physico-Chimie des Matériaux (LAF 502), Ecole Normale Supérieure, Université Mohammed V-Agdal, BP 5118 Rabat (Morocco); Boukhari, A. [Laboratoire de Chimie du Solide Appliquée, Faculté des Sciences, Université Mohammed V-Agdal, Avenue Ibn Batouta, BP 1014 Rabat (Morocco)

2013-11-15

Electrical properties of Pb{sub 2}Na{sub 0.8}Eu{sub 0.2}Nb{sub 4.8}Fe{sub 0.2}O{sub 15} tungsten bronze compound were investigated. Ferroelectric phase transition of diffuse type is observed at 395 °C. Conductivity study as a function of temperature (RT-600 °C) and at three different frequencies (10, 100 and 1000 kHz) suggests the existence of dominant ionic conduction. The rise of ac conductivity on increasing temperature supports the NTCR (negative temperature coefficient of resistance) behaviour of the material. The activation energies have been evaluated from ac conductivity using Arrhenius equation and discussed. Different conduction mechanisms were identified. For comparison, the conducting properties of Pb{sub 2}Na{sub 0.8}R{sub 0.2}Nb{sub 4.8}Fe{sub 0.2}O{sub 15} (R=Dy, Nd, La) were also investigated. - Graphical abstract: Thermal evolution of lnσ{sub ac} of Pb{sub 2}Na{sub 0.8}Eu{sub 0.2}Nb{sub 4.8}Fe{sub 0.2}O{sub 15} at selected frequencies. Display Omitted - Highlights: • We found that TB compounds exhibit a diffuse type of first- order transition. • A negative temperature coefficient of resistance (NTCR) behaviour is observed. • Three conduction mechanisms were identified: n-and/or p-type at low temperatures. • The conduction mechanism in the studied compounds is very complex.

Effect of microstructure on the high temperature mechanical properties of (CeO{sub 2}){sub 0.8}(GdO{sub 1.5}){sub 0.2} electrolytes

Energy Technology Data Exchange (ETDEWEB)

Sammes, N.M.; Zhang, Y. [Univ. of Waikato, Hamilton (New Zealand)

1996-12-31

CeO{sub 2}-based oxides have recently been shown to have great potential as electrolytes in medium temperature solid oxide fuel cell applications, primarily due to their high ionic conductivity. Steele et al., for example, have examined a cell of the type: O{sub 2}, La{sub 0.6}Sr{sub 0.4}Fe{sub 0.8}Co{sub 0.2}O{sub 3}{vert_bar}Ce{sub 0.9}Gd{sub 0.1}O{sub 1.95}{vert_bar}Ni-ZrO{sub 2}, H{sub 2}/H{sub 2}O at 715{degrees}C. Gd{sub 2}O{sub 3} doped CeO{sub 2} has been reported as having one of the highest oxygen ion conductivities of the ceria-based materials. An ionic conductivity of 8.3 x 10{sup -2} s/cm has been reported for (CeO{sub 2}){sub 0.8}(GdO{sub 1.5}){sub 0.2} at 800{degrees}C, which is approximately four times that of Y{sub 2}O{sub 3}-doped ZrO{sub 2}, at the same temperature. Although the electrical properties of the material have been examined in detail, very little work has considered the microstructural/property relationships, particularly in relation to the mechanical properties. It is well know that CeO{sub 2}-based materials are difficult to density and attempts have been performed to examine this. Preliminary studies have also been undertaken to examine the effect of sintering on the mechanical properties of the material. In this paper we examine the effect of microstructure on the high temperature mechanical properties of (CeO{sub 2}){sub 0.8}(GdO{sub 1.5}){sub 0.2}.

Stabilization/solidification of selenium-impacted soils using Portland cement and cement kiln dust

International Nuclear Information System (INIS)

Moon, Deok Hyun; Grubb, Dennis G.; Reilly, Trevor L.

2009-01-01

Stabilization/solidification (S/S) processes were utilized to immobilize selenium (Se) as selenite (SeO 3 2- ) and selenate (SeO 4 2- ). Artificially contaminated soils were prepared by individually spiking kaolinite, montmorillonite and dredged material (DM; an organic silt) with 1000 mg/kg of each selenium compound. After mellowing for 7 days, the Se-impacted soils were each stabilized with 5, 10 and 15% Type I/II Portland cement (P) and cement kiln dust (C) and then were cured for 7 and 28 days. The toxicity characteristic leaching procedure (TCLP) was used to evaluate the effectiveness of the S/S treatments. At 28 days curing, P doses of 10 and 15% produced five out of six TCLP-Se(IV) concentrations below 10 mg/L, whereas only the 15% C in DM had a TCLP-Se(IV) concentration 3 .H 2 O) and selenate substituted ettringite (Ca 6 Al 2 (SeO 4 ) 3 (OH) 12 .26H 2 O), respectively.

Size dependent magnetic and magneto-optical properties of Ni{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Li, Oksana A., E-mail: log85@mail.ru [Department of Applied Physics, National Pingtung University, Pingtung 90003, Taiwan (China); Siberian Federal University, Krasnoyarsk 660041 (Russian Federation); Lin, Chun-Rong, E-mail: crlin@mail.nptu.edu.tw [Department of Applied Physics, National Pingtung University, Pingtung 90003, Taiwan (China); Chen, Hung-Yi; Hsu, Hua-Shu [Department of Applied Physics, National Pingtung University, Pingtung 90003, Taiwan (China); Shih, Kun-Yauh [Department of Applied Chemistry, National Pingtung University, Pingtung 90003, Taiwan (China); Edelman, Irina S. [L.V. Kirensky Institute of Physics, SB RAS, Krasnoyarsk 660036 (Russian Federation); Wu, Kai-Wun; Tseng, Yaw-Teng [Department of Applied Physics, National Pingtung University, Pingtung 90003, Taiwan (China); Ovchinnikov, Sergey G. [Siberian Federal University, Krasnoyarsk 660041 (Russian Federation); L.V. Kirensky Institute of Physics, SB RAS, Krasnoyarsk 660036 (Russian Federation); Lee, Jiann-Shing [Department of Applied Physics, National Pingtung University, Pingtung 90003, Taiwan (China)

2016-06-15

Ni{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} spinel nanoparticles have been synthesized by combustion method. Average particles size varies from 15.5 to 50.0 nm depending on annealing temperature. Correlations between particles size and magnetic and magneto-optical properties are investigated. Magnetization dependences on temperature and external magnetic field correspond to the sum of paramagnetic and superparamagnetic response. Critical size of single-domain transition is found to be 15.9 nm. Magnetic circular dichroism (MCD) studies of nickel zinc spinel are presented here for the first time. The features in magnetic circular dichroism spectrum are assigned to the one-ion d–d transitions in Fe{sup 3+} and Ni{sup 2+} ions, as well to the intersublattice and intervalence charge transfer transitions. The MCD spectrum rearrangement was revealed with the change of the nanoparticles size. - Highlights: • Ni{sub 0.2}Zn{sub 0.8}Fe{sub 2}O{sub 4} nanoparticles were synthesized by combustion method. • Structure and magnetic properties are studied. • Magnetic circular dichroism (MCD) of nickel zinc spinel was measured for the first time. • The MCD spectrum rearrangement was revealed with the change of the nanoparticles size.

Pembuatan La0,8Ca0,2MnO3 sebagai Katoda pada Solid Oxide Fuel Cell (SOFC dan Karakteristiknya

Directory of Open Access Journals (Sweden)

Riska Ekawati

2007-06-01

Full Text Available The making of La0,8Ca0,2MnO3 cathode material of solid oxide fuel cell from lanthanum oxide (La2O3, calcium oxide (CaO, and manganese carbonate hydrate (MnCO3.H2O has been done using tape casting method. Time of firing the La0,8Ca0,2MnO3 varied. The values of t = 30 minutes, 60 minutes and 120 minutes. Microstructure of these materials was analyzed and characterized by means of their electric conductivity, XRD (x ray diffraction and SEM (scanning electron microscope. It is found that formulated micro structure is orthorhombic. The result of measurement shows that density is in linear (positive correlation with increasing of holding time of firing, porosity and coefficient of thermal expansion is negatively correlated with density and electric conductivity is in linear (positive correlation with increase density.

Effect of poling process on piezoelectric properties of BCZT - 0.08 wt.% CeO{sub 2} lead-free ceramics

Energy Technology Data Exchange (ETDEWEB)

Chandrakala, E.; Praveen, J. Paul; Das, Dibakar, E-mail: ddse@uohyd.ernet.in [School of Engineering Sciences & Technology, University of Hyderabad, Hyderabad 500046 (India)

2016-05-06

The properties of lead free piezoelectric materials can be tuned by suitable doping in the A and B sites of the perovskite structure. In the present study, cerium has been identified as a dopant to investigate the piezoelectric properties of lead-free BCZT system. BCZT – 0.08 wt.%CeO{sub 2} lead-free ceramics have been synthesized using sol-gel technique and the effects of CeO{sub 2} dopant on their phase structure and piezoelectric properties were investigated systematically. Poling conditions, such as temperature, electric field, and poling time have been optimized to get enhanced piezoelectric response. The optimized poling conditions (50°C, 3Ec and 30min) resulted in high piezoelectric charge coefficient d{sub 33} ~ 670pC/N, high electromechanical coupling coefficient k{sub p} ~ 60% and piezoelectric voltage coefficient g{sub 33} ~ 14 mV.m/N for BCZT – 0.08wt.% CeO{sub 2} ceramics.

Effects of Zr4+ codoping on the Lu0.8Sc0.2BO3:Ce scintillation materials

International Nuclear Information System (INIS)

Wu, Yuntao; Ren, Guohao; Ding, Dongzhou; Shang, Shanshan; Sun, Dandan; Zhang, Guoqing; Wang, Jiayu; Pan, Shangke; Yang, Fan

2013-01-01

Both Zr-codoped Lu 0.8 Sc 0.2 BO 3 :Ce polycrystalline powders and single crystals were obtained by solid-state reaction and Czochralski method, respectively. The effects of Zr codoping on the optical absorption, Ce 3+ /Ce 4+ ratio, scintillation efficiency, decay time and point defect in Lu 0.8 Sc 0.2 BO 3 :Ce materials were examined systematically. Our results show that there is no positive contribution of Zr 4+ ion codoping to the scintillation efficiency. And the reasons for the deterioration of scintillation efficiency by codoping Zr 4+ were revealed. - Highlights: ► No positive contribution of the Zr 4+ ions on the scintillation efficiency was found. ► New optical absorption band was in the region from 200 to 225 nm. ► Continuously accelerated decay time indicated that Zr 4+ codoping induced new point defects. ► The induced hole trap located at 1.91 eV below the conduction band.

The high-pressure structural configurations of Ca_0.2Sr_0.8Al₂Si ₂O₈ feldspar

DEFF Research Database (Denmark)

Benna, Piera; Nestola, Fabrizio; Boffa Ballaran, Tiziana

2007-01-01

Single-crystal in situ high-P X-ray diffraction was performed at P = 0.0001, 3.2, 4.4, 6.2, and 7.4 GPa on synthetic Ca0.2Sr0.8Al2Si2O8 feldspar (An20SrF80). Data collections conÞ rmed the displacive Þ rst-order triclinic I1-monoclinic I2/c phase transition at P ~4.3 GPa found in a previous high-...

Comparison of leach results from field and laboratory prepared samples

International Nuclear Information System (INIS)

Oblath, S.B.; Langton, C.A.

1985-01-01

The leach behavior of saltstone prepared in the laboratory agrees well with that from samples mixed in the field using the Littleford mixer. Leach rates of nitrates and cesium from the current reference formulation saltstone were compared. The laboratory samples were prepared using simulated salt solution; those in the field used Tank 50 decontaminated supernate. For both nitrate and cesium, the field and laboratory samples showed nearly identical leach rates for the first 30 to 50 days. For the remaining period of the test, the field samples showed higher leach rates with the maximum difference being less than a factor of three. Ruthenium and antimony were present in the Tank 50 supernate in known amounts. Antimony-125 was observed in the leachate and a fractional leach rate was calculated to be at least a factor of ten less than that of 137 Cs. No 106 Ru was observed in the leachate, and the release rate was not calculated. However, based on the detection limits for the analysis, the ruthenium leach rate must also be at least a factor of ten less than cesium. These data are the first measurements of the leach rates of Ru and Sb from saltstone. The nitrate leach rates for these samples were 5 x 10 -5 grams of nitrate per square cm per day after 100 days for the laboratory samples and after 200 days for the field samples. These values are consistent with the previously measured leach rates for reference formulation saltstone. The relative standard deviation in the leach rate is about 15% for the field samples, which all were produced from one batch of saltstone, and about 35% for the laboratory samples, which came from different batches. These are the first recorded estimates of the error in leach rates for saltstone

Degradation of cementitious materials associated with salstone disposal units

Energy Technology Data Exchange (ETDEWEB)

Flach, G. P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Smith, F. G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2014-09-01

The Saltstone facilities at the DOE Savannah River Site (SRS) stabilize and dispose of low-level radioactive salt solution originating from liquid waste storage tanks at the site. The Saltstone Production Facility (SPF) receives treated salt solution and mixes the aqueous waste with dry cement, blast furnace slag, and fly ash to form a grout slurry which is mechanically pumped into concrete disposal cells that compose the Saltstone Disposal Facility (SDF). The solidified grout is termed “saltstone”. Cementitious materials play a prominent role in the design and long-term performance of the SDF. The saltstone grout exhibits low permeability and diffusivity, and thus represents a physical barrier to waste release. The waste form is also reducing, which creates a chemical barrier to waste release for certain key radionuclides, notably Tc-99. Similarly, the concrete shell of a saltstone disposal unit (SDU) represents an additional physical and chemical barrier to radionuclide release to the environment. Together the waste form and the SDU compose a robust containment structure at the time of facility closure. However, the physical and chemical state of cementitious materials will evolve over time through a variety of phenomena, leading to degraded barrier performance over Performance Assessment (PA) timescales of thousands to tens of thousands of years. Previous studies of cementitious material degradation in the context of low-level waste disposal have identified sulfate attack, carbonation influenced steel corrosion, and decalcification (primary constituent leaching) as the primary chemical degradation phenomena of most relevance to SRS exposure conditions. In this study, degradation time scales for each of these three degradation phenomena are estimated for saltstone and concrete associated with each SDU type under conservative, nominal, and best estimate assumptions.

In situ X-ray and neutron diffraction of the Ruddlesden–Popper compounds (RE2−xSrx)0.98(Fe0.8Co0.2)1−yMgyO4−δ (RE=La, Pr): Structure and CO2 stability

International Nuclear Information System (INIS)

Chatzichristodoulou, C.; Hauback, B.C.; Hendriksen, P.V.

2013-01-01

The crystal structure of the Ruddlesden–Popper compounds (La 1.0 Sr 1.0 ) 0.98 Fe 0.8 Co 0.2 O 4−δ and (La 1.2 Sr 0.8 ) 0.98 (Fe 0.8 Co 0.2 ) 0.8 Mg 0.2 O 4−δ was investigated at 1000 °C in N 2 (a O2 =1×10 −4 ) by in-situ powder neutron diffraction. In-situ powder X-ray diffraction (PXD) was also employed to investigate the temperature dependence of the lattice parameters of the compounds in air and the oxygen activity dependence of the lattice parameters at 800 °C and 1000 °C. The thermal and chemical expansion coefficients, determined along the two crystallographic directions of the tetragonal unit cell, are highly anisotropic. The equivalent pseudo-cubic thermal and chemical expansion coefficients are in agreement with values determined by dilatometry. The chemical stability in CO 2 containing environments of various Ruddlesden–Popper compounds with chemical formula (RE 2−x Sr x ) 0.98 (Fe 0.8 Co 0.2 ) 1−y Mg y O 4−δ (RE=La, Pr), as well as their stability limit in H 2 /H 2 O=4.5 were also determined by in-situ PXD for x=0.9, 1.0 and y=0, 0.2. - Graphical abstract: Influence of electronic configuration on bond length, lattice parameters and anisotropic thermal and chemical expansion. Highlights: ► The thermal and chemical expansion coefficients are largely anisotropic. ► The expansion of the perovskite layers is constrained along the a direction. ► The studied compositions show remarkable thermodynamic stability upon reduction. ► The thermal and chemical expansion coefficients are lower than related perovskites. ► The investigated materials decompose in CO 2 containing atmospheres

Results for the First, Second, and Third Quarter Calendar Year 2015 Tank 50H WAC slurry samples chemical and radionuclide contaminants

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-02-18

This report details the chemical and radionuclide contaminant results for the characterization of the Calendar Year (CY) 2015 First, Second, and Third Quarter sampling of Tank 50H for the Saltstone Waste Acceptance Criteria (WAC) in effect at that time. Information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering (D&S-FE) to support the transfer of low-level aqueous waste from Tank 50H to the Salt Feed Tank in the Saltstone Facility in Z-Area, where the waste will be immobilized. This information is also used to update the Tank 50H Waste Characterization System. Previous memoranda documenting the WAC analyses results have been issued for these three samples.

Lead-free Ba0.8Ca0.2(ZrxTi1−x)O3 ceramics with large electrocaloric effect

International Nuclear Information System (INIS)

Asbani, B.; Dellis, J.-L.; Lahmar, A.; Gagou, Y.; El Marssi, M.; Courty, M.; Djellab, K.; Amjoud, M.; Mezzane, D.; Kutnjak, Z.

2015-01-01

The electrocaloric effect was investigated in lead-free Zr doped Ba 0.8 Ca 0.2 (Zr x Ti 1−x )O 3 (BCTZ) ceramics synthesized by a conventional sintering process. Room-temperature x-ray diffraction analysis showed that the tetragonal structure is obtained in BCTZ for x ≤ 0.08 and a pseudo cubic phase for x > 0.08. The dielectric spectroscopy and calorimetry revealed that the Curie temperature decreases as a consequence of Zr doping and that the BCTZ exhibits a first order ferroelectric phase transition. The electrocaloric effect was determined by the calculation of the electrocaloric change of temperature (ΔT) using the Maxwell relation based on the P–E hysteresis loops measured at different temperatures. A large electrocaloric responsivity ΔT/ΔE = 0.34 × 10 −6  Km/V was found for x = 0.04, which significantly exceeds of values found so far in other lead-free electrocaloric materials

Low-temperature resistivity anomaly in underdoped Pr0.8Sr0.2MnO3 manganite nanoparticles

International Nuclear Information System (INIS)

Das, Proloy T.; Giri, S.K.; Panda, J.; Taraphder, A.; Nath, T.K.; Nigam, A.K.

2013-01-01

High resolution electrical resistivity measurements were carried out of under-doped Pr 0.8 Sr 0.2 MnO 3 manganite nanoparticles with grain size modulation down to 40 nm in magnetic fields H, from 0 to 9 T in the low temperature regime down to a temperature of 4.2 K. In the temperature range below 80 K, a distinct resistivity minima is observed for all the samples with different particle sizes for all H. While trying to fit low temperature resistivity data with different models for the observed resistivity minima with negative temperature coefficient of resistance (TCR) for all H, it appears that all the data for different particle sizes, can be best described by electron-electron (e-e) interaction effect in comparison with other models, e.g., Kondo model, coulomb blockades etc. The low temperature data for all H have been fitted with an expression containing three terms, namely, residual resistivity, inelastic scattering, e-e interaction and Kondo effects. We conclude that the e-e interaction is the dominant transport mechanism at low temperatures for the observed negative TCR in this strongly disordered nanometric Pr 0.8 Sr 0.2 MnO 3 phase separated manganite system. (author)

Dicty_cDB: FC-AI08 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available FC (Link to library) FC-AI08 (Link to dictyBase) - G01729 DDB0233148 Contig-U14939-1 FC-AI...08P (Link to Original site) FC-AI08F 654 FC-AI08Z 563 FC-AI08P 1217 - - Show FC-AI08 Library FC (Link... to library) Clone ID FC-AI08 (Link to dictyBase) Atlas ID - NBRP ID G01729 dictyBase ID DDB0233148 Link to ...Contig Contig-U14939-1 Original site URL http://dictycdb.biol.tsukuba.ac.jp/CSM/FC/FC-AI/FC-AI...08Q.Seq.d/ Representative seq. ID FC-AI08P (Link to Original site) Representative DNA sequence >FC-AI08 (FC-AI

Leachability of Arsenic and Heavy Metals from Mine Tailings of Abandoned Metal Mines

Science.gov (United States)

Lim, Mihee; Han, Gi-Chun; Ahn, Ji-Whan; You, Kwang-Suk; Kim, Hyung-Seok

2009-01-01

Mine tailings from an abandoned metal mine in Korea contained high concentrations of arsenic (As) and heavy metals [e.g., As: 67,336, Fe: 137,180, Cu: 764, Pb: 3,572, and Zn: 12,420 (mg/kg)]. US EPA method 6010 was an effective method for analyzing total arsenic and heavy metals concentrations. Arsenic in the mine tailings showed a high residual fraction of 89% by a sequential extraction. In Toxicity Characteristic Leaching Procedure (TCLP) and Korean Standard Leaching Test (KSLT), leaching concentrations of arsenic and heavy metals were very low [e.g., As (mg/L): 0.4 for TCLP and 0.2 for KSLT; cf. As criteria (mg/L): 5.0 for TCLP and 1.5 for KSLT]. PMID:20049231

Assessment of cement kiln dust (CKD) for stabilization/solidification (S/S) of arsenic contaminated soils.

Science.gov (United States)

Moon, Deok Hyun; Wazne, Mahmoud; Yoon, In-Ho; Grubb, Dennis G

2008-11-30

A stabilization/solidification (S/S) process for arsenic (As) contaminated soils was evaluated using cement kiln dust (CKD). Laboratory-prepared slurries, made of either kaolinite or montmorillonite, and field soils spiked with either As(3+) or As(5+) were prepared and treated with CKD ranging from 10 to 25 wt%. Sodium arsenite and sodium arsenate at 0.1 wt% were used to simulate arsenite (As(3+)) and arsenate (As(5+)) source contamination in soils, respectively. The effectiveness of treatment was evaluated at curing periods of 1- and 7-days based on the toxicity characteristic leaching procedure (TCLP). As-CKD and As-clay-CKD slurries were also spiked at 10 wt% to evaluate As immobilization mechanism using X-ray powder diffraction (XRPD) analyses. Overall, the TCLP results showed that only the As(5+) concentrations in kaolinite amended with 25 wt% CKD after 1 day of curing were less than the TCLP regulatory limit of 5mg/L. Moreover, at 7 days of curing, all As(3+) and As(5+) concentrations obtained from kaolinite soils were less than the TCLP criteria. However, none of the CKD-amended montmorillonite samples satisfied the TCLP-As criteria at 7 days. Only field soil samples amended with 20 wt% CKD complied with the TCLP criteria within 1 day of curing, where the source contamination was As(5+). XRPD and scanning electron microscopy (SEM)-energy dispersive X-ray spectroscopy (EDX) results showed that Ca-As-O and NaCaAsO(4).7.5H(2)O were the primary phases responsible for As(3+) and As(5+) immobilization in the soils, respectively.

Assessment of cement kiln dust (CKD) for stabilization/solidification (S/S) of arsenic contaminated soils

International Nuclear Information System (INIS)

Moon, Deok Hyun; Wazne, Mahmoud; Yoon, In-Ho; Grubb, Dennis G.

2008-01-01

A stabilization/solidification (S/S) process for arsenic (As) contaminated soils was evaluated using cement kiln dust (CKD). Laboratory-prepared slurries, made of either kaolinite or montmorillonite, and field soils spiked with either As 3+ or As 5+ were prepared and treated with CKD ranging from 10 to 25 wt%. Sodium arsenite and sodium arsenate at 0.1 wt% were used to simulate arsenite (As 3+ ) and arsenate (As 5+ ) source contamination in soils, respectively. The effectiveness of treatment was evaluated at curing periods of 1- and 7-days based on the toxicity characteristic leaching procedure (TCLP). As-CKD and As-clay-CKD slurries were also spiked at 10 wt% to evaluate As immobilization mechanism using X-ray powder diffraction (XRPD) analyses. Overall, the TCLP results showed that only the As 5+ concentrations in kaolinite amended with 25 wt% CKD after 1 day of curing were less than the TCLP regulatory limit of 5 mg/L. Moreover, at 7 days of curing, all As 3+ and As 5+ concentrations obtained from kaolinite soils were less than the TCLP criteria. However, none of the CKD-amended montmorillonite samples satisfied the TCLP-As criteria at 7 days. Only field soil samples amended with 20 wt% CKD complied with the TCLP criteria within 1 day of curing, where the source contamination was As 5+ . XRPD and scanning electron microscopy (SEM)-energy dispersive X-ray spectroscopy (EDX) results showed that Ca-As-O and NaCaAsO 4 .7.5H 2 O were the primary phases responsible for As 3+ and As 5+ immobilization in the soils, respectively

Isolation and characterization of a novel 2-methyl-4-chlorophenoxyacetic acid-degrading Enterobacter sp. strain SE08.

Science.gov (United States)

Tan, Lin; Hu, Qiulong; Xiong, Xingyao; Su, Xiaojun; Huang, Yanning; Jiang, Ziwei; Zhou, Qingming; Zhao, Songyi; Zeng, Wei-ai

2013-10-01

A bacterial strain (SE08) capable of utilizing 2-methyl-4-chlorophenoxy acetic acid (MCPA) as the sole carbon and energy source for growth was isolated by continuous enrichment culturing in minimal salt medium (MSM) from a long term MCPA exposed soil. This bacterial strain was identified as Enterobacter sp. based on morphological, physiological and biochemical tests, as well as 16S rRNA sequence analysis. Its ability to degrade MCPA was determined using high performance liquid chromatography. The strain SE08 can tolerate unusually high MCPA concentrations (125-2000mg/L). The influences of culturing factors (initial concentration, pH, and temperature) on the bacterial growth and substrate degradation were studied. The results showed that the optimal MCPA degradation occurred at an MCPA concentration of 500mg/L, 30°C and pH 6.0. Under these conditions, 68.5 percent of MCPA in MSM was degraded by SE08, and the OD600nm reached 0.64 after culturing for 72h. The degradation of MCPA could be enhanced by addition of both carbon and nitrogen sources. At an initial MCPA concentration of 500mg/L, when 5g/L glucose and 2.5g/L yeast extract were added into the MSM media, the MCPA degradation was significantly increased to 83.8 percent, and OD600nm was increased to 1.09 after incubation at 30°C and pH 6.0 for 72h. This is the first study showing that an Enterobacter sp. strain is capable of degrading MCPA, which might provide a new approach for the remediation of MCPA contaminated soil and contribute to the limited knowledge about the function of Enterobacter species. Crown Copyright © 2013. Published by Elsevier Inc. All rights reserved.

Amobilisasi Sel Bacillus licheniformis KA-08 dalam Menghasilkan Keratinase Termostabil

Directory of Open Access Journals (Sweden)

Anthoni Agustien

2012-10-01

Full Text Available Isolate local Bacillus licheniformis KA-08 known extracellular thermostable keratinase producers. Scale up of thermostable keratinase production can be with cells immobilized. The objective of the research is to thermostable keratinase production of B. licheniformis KA-08 cells immobilization. Thermostable keratinase activities were determined with modification of Brandelli and Riffel method. Protein concentration of enzyme determined with Lowry method. Immobilization of cells by Ca-alginate matrix with Adinarayana method, alginate concentration and amount of alginate bead effects with Beshay method. The result extracellular thermostable keratinase of B. licheniformis KA-08 cells immobilized was maximum produced at 12 times incubation with activity as 9.25 U/mg. Three percent alginate has optimum activity. Three hundred alginate beads has optimum activity. Cells immobilized ofB. licheniformis KA-08 has scale up of thermostable keratinase activity at 2 times than free cells. Thermostable keratinase produced by cell immobilized was nine cycles.

NCBI nr-aa BLAST: CBRC-DSIM-08-0039 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DSIM-08-0039 ref|YP_026083.1| NADH dehydrogenase subunit 2 [Steinernema carpoc...apsae] gb|AAT00526.1| NADH dehydrogenase subunit 2 [Steinernema carpocapsae] YP_026083.1 7e-06 31% ...

Unigene BLAST: CBRC-DMEL-08-0057 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0057 gnl|UG|Dm#S40593121 DMG1C.2_1.G07.C1 MODENCODE_DM_A Drosophila melanogaster cDNA clone DMG...1-chr3R.3.082.a, mRNA sequence /clone=DMG1-chr3R.3.082.a /gb=EW713160 /gi=156142114 /ug=Dm.27906 /len=1533 2e-06 22% ...

Academic Training - 2nd Term: 08.01.2007 - 31.03.2007

CERN Multimedia

2006-01-01

2006 - 2007 ACADEMIC TRAINING PROGRAMME 2nd Term : 08.01.2007 - 31.03.2007 LECTURE SERIES Applied Superconductivity by V. Palmieri, INFN, Padova, It. 17, 18, 19 January 11:00 -1200 - Auditorium, Bldg 500 String Theory for Pedestrians by B. Zwiebach, M.I.T. Cambridge, USA 29, 30, 31 January 11:00-12:00 - Auditorium, Bldg 500 on 29, 30 January TH Auditorium on 31 January Introduction to Supersymmetry by D. Kaplan, John Hopkins University, Baltimore, USA 12, 13, 14, 15 February 11:00-12:00 - Auditorium, Bldg 500 The Hunt for the Higgs Particle by F. Zwirner, University of Padova, It 27, 28 February, 1st March 11:00-12:00 - Auditorium, Bldg 500 From Evolution Theory to Parallel and Distributed Genetic by F. Fernandez de Vega 15, 16, March 11:00-12:00 - Auditorium, Bldg 500 The lectures are open to all those interested, without application. The abstract of the lectures, as well as any change to the above information (title, dates, time, place etc.) will be published in the CERN bulletin, the WWW, an...

Academic Training - 2nd Term: 08.01.2007 - 31.03.2007

CERN Multimedia

2006-01-01

2006 - 2007 ACADEMIC TRAINING PROGRAMME 2nd Term : 08.01.2007 - 31.03.2007 LECTURE SERIES Applied Superconductivity by V. Palmieri, INFN, Padova, It. 17, 18, 19 January 11:00 -1200 - Auditorium, bldg. 500 String Theory for Pedestrians by B. Zwiebach, M.I.T. Cambridge, USA 29, 30, 31 January 11:00-12:00 - Auditorium, bldg. 500 on 29, 30 January TH Auditorium on 31 January Introduction to Supersymmetry by D. Kaplan, John Hopkins University, Baltimore, USA 12, 13, 14, 15 February 11:00-12:00 - Auditorium, bldg. 500 The Hunt for the Higgs Particle by F. Zwirner, University of Padova, It 27, 28 February, 1st March 11:00-12:00 - Auditorium, bldg. 500 From Evolution Theory to Parallel and Distributed Genetic Programming by F. Fernandez de Vega 15, 16, March 11:00-12:00 - Auditorium, bldg. 500 The lectures are open to all those interested, without application. The abstract of the lectures, as well as any change to the above information (title, dates, time, place etc.) will be published in the WWW, and ...

Radiosensitization and relative mechanisms of vanillin derivative BVAN08 on human glioma U-251 cells

International Nuclear Information System (INIS)

Wang Shubin; Zhang Bo; Sun Weijian; Wang Yu; Liu Xiaodan; Xu Qinzhi; Zhou Pingkun

2010-01-01

Objective: To provide more convincing evidences and experimental data for exploring vanillin derivative BVAN08, 6-bromine-5-hydroxy-4-methoxy-benzaldehyde, as a new anticancer drug, and to investigate the effect on the growth, radiosensitization of human glioma cell line U-251 and the relative mechanism. Methods: The effect of BVAN08 on cell proliferation of U-251 and radiosensitivity to 60 Co γ-rays (irradiation dose rate 2.3 Gy/min) were analyzed with MTT and colony-forming ability assay. Change in cellular morphology was observed by using light microscope. Change in cell cycle and apoptosis was detected with flow cytometry. The autophagy was observed by using TEM (irradiation dose rate is transmission electron microscope). DNA-PKcs protein level was detected through Western blot analysis. Results: BVAN08 exhibited a dose- and time-dependent inhibition on the proliferation of U-251 cells during the concentration range of 10-100 mol/L (t=1.83-3.07, P 50 at 48 h and 72 h after administration with BVAN08 were 55.3 and 52.7 mol/L, respectively. Obvious G 2 /M arrest was induced in U-251 cells after 4 h administration with BVAN08, and reached peck at 12 h. The G 2 /M population reached 63.3% in U-251 cells after 12 h administration of 60 μmol/L BVAN08 and kept increasing with the time, while both apoptosis and autophagic cell death were induced. The most effective radiosensitization time for BVAN08 treatment was 12 h before irradiation. The enhancement ratio of radiosensitivity was 3.14 for 20 μmol/L of BVAN08 12 h before 2 Gy irradiation. Conclusions: BVAN08 can induce apoptosis as radiosensitizing effect might be associated with the induction of G 2 /M arrest and inhibition of DNA-PKcs expression. BVAN08 seemed to be a promising radiosensitizing anticancer drug. (authors)

Effect of Sr substituted La 2−x Sr x NiO 4+δ (x = 0, 0.2, 0.4, 0.6, and 0.8) on oxygen stoichiometry and oxygen transport properties

KAUST Repository

Inprasit, T.; Wongkasemjit, S.; Skinner, S. J.; Burriel, M.; Limthongkul, P.

2015-01-01

© The Royal Society of Chemistry 2015. Stoichiometry and oxygen diffusion properties of La2-xSrxNiO4±δ with x = 0.2, 0.4, 0.6, and 0.8 prepared via a sol-gel method were investigated in this study. Iodometric titration and thermogravimetric analysis were used to determine the oxygen non-stoichiometry. Over the entire compositional range, the samples exhibit oxygen hyperstoichiometry with the minimum value δ = 0.14 at x = 0.4. Mixed effects of reduction of oxygen excess and increasing valence of Ni were found to serve as charge compensation mechanisms; the former dominated at a low level of substitution, x < 0.4, while the latter dominated at higher levels of Sr (0.4 < x < 0.8). The highest oxygen diffusion coefficient was found for the minimum amount of Sr substitution, x = 0.2, continuously decreasing with x until x = 0.6. An unusual increase in D∗ was observed when the Sr content increased up to x = 0.8.

NCBI nr-aa BLAST: CBRC-DSIM-08-0052 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DSIM-08-0052 ref|YP_926427.1| sensor histidine kinase [Shewanella amazonensis ...SB2B] gb|ABL98757.1| sensor histidine kinase [Shewanella amazonensis SB2B] YP_926427.1 1.6 32% ...

76 FR 60871 - In the Matter of Certain Toner Cartridges and Components Thereof; Notice of Commission Final...

Science.gov (United States)

2011-09-30

...-Toner''); Alpha Image Tech of South El Monte, California (``Alpha Image''); ACM Technologies, Inc. of Corona, California (``ACM''); Virtual Imaging Products Inc. of North York, Ontario; Acecom Inc.--San... Image, Copy Tech, LTT, C&R, ACM, Ink Master, Direct Billing, Ink Tech, QCI, IJSS, Acecom, Ninestar Tech...

NCBI nr-aa BLAST: CBRC-MDOM-08-0130 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0130 ref|NP_001138971.1| bitter taste receptor Cafa-T2R3 [Canis lupus ...familiaris] dbj|BAE80329.1| bitter taste receptor [Canis lupus familiaris] NP_001138971.1 2e-66 45% ...

NCBI nr-aa BLAST: CBRC-MDOM-08-0126 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0126 ref|NP_001138971.1| bitter taste receptor Cafa-T2R3 [Canis lupus ...familiaris] dbj|BAE80329.1| bitter taste receptor [Canis lupus familiaris] NP_001138971.1 2e-64 45% ...

NCBI nr-aa BLAST: CBRC-MDOM-08-0135 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0135 ref|NP_001138972.1| bitter taste receptor Cafa-T2R38 [Canis lupus... familiaris] dbj|BAE80335.1| bitter taste receptor [Canis lupus familiaris] NP_001138972.1 2e-80 52% ...

NCBI nr-aa BLAST: CBRC-MDOM-08-0125 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0125 ref|NP_001138971.1| bitter taste receptor Cafa-T2R3 [Canis lupus ...familiaris] dbj|BAE80329.1| bitter taste receptor [Canis lupus familiaris] NP_001138971.1 2e-22 38% ...

A CONSISTENT STUDY OF METALLICITY EVOLUTION AT 0.8 < z < 2.6

International Nuclear Information System (INIS)

Wuyts, Eva; Kurk, Jaron; Förster Schreiber, Natascha M.; Genzel, Reinhard; Wisnioski, Emily; Bandara, Kaushala; Wuyts, Stijn; Beifiori, Alessandra; Bender, Ralf; Buschkamp, Peter; Chan, Jeffrey; Davies, Ric; Eisenhauer, Frank; Fossati, Matteo; Kulkarni, Sandesh K.; Lang, Philipp; Brammer, Gabriel B.; Burkert, Andreas; Carollo, C. Marcella; Lilly, Simon J.

2014-01-01

We present the correlations between stellar mass, star formation rate (SFR), and the [N II]/Hα flux ratio as an indicator of gas-phase metallicity for a sample of 222 galaxies at 0.8 < z < 2.6 and log (M * /M ☉ ) = 9.0-11.5 from the LUCI, SINS/zC-SINF, and KMOS 3D surveys. This sample provides a unique analysis of the mass-metallicity relation (MZR) over an extended redshift range using consistent data analysis techniques and a uniform strong-line metallicity indicator. We find a constant slope at the low-mass end of the relation and can fully describe its redshift evolution through the evolution of the characteristic turnover mass where the relation begins to flatten at the asymptotic metallicity. At a fixed mass and redshift, our data do not show a correlation between the [N II]/Hα ratio and SFR, which disagrees with the 0.2-0.3 dex offset in [N II]/Hα predicted by the ''fundamental relation'' between stellar mass, SFR, and metallicity discussed in recent literature. However, the overall evolution toward lower [N II]/Hα at earlier times does broadly agree with these predictions

Structural, magnetic and transport studies of Mn0.8Cr0.2CoGe alloy

Science.gov (United States)

Das, S. C.; Dutta, P.; Pramanick, S.; Chatterjee, S.

2018-04-01

Different physical and functional properties of Mn0.8Cr0.2CoGe alloy has been investigated through structural, magnetic and electrical transport measurements. Substitution of Cr for Mn results significant decrease in both structural and magnetic transition temperature and brings them well below the room temperature. A reasonable amount of conventional magnetocaloric effect (ΔS˜ - 2.22 J/kg-K for magnetic field (H) changing from 0 to 50 kOe) with large relative cooling power (251.7 J/kg for H changing from 0 to 50 kOe) has also been observed around the region of transition. On thermal cycling through the structural transition, noticeable training effect is found to be associated with the resistivity of the alloy.

Evaluation report on SCTF Core-II test S2-08

International Nuclear Information System (INIS)

Ohnuki, Akira; Iwamura, Takamichi; Abe, Yutaka; Murao, Yoshio; Adachi, Hiromichi.

1991-01-01

The present report investigates the effects of the difference of the core inlet subcooling during reflood in a PWR-LOCA on the thermal-hydraulic behaviors including two-dimensional behaviors in the pressure vessel in the Slab Core Test Facility (SCTF) Core-II tests under gravity feed mode. The following test results are examined: Tests S2-02 (Reference test) and Test S2-08 (High subcooling test). The degree of the difference of the subcooling between the two tests was about 20 to 35 K in the LPCI period. The following conclusions were obtained from this study: (1) Higher the subcooling gave larger amount of water accumulation in the core and gave better core cooling. These tendencies were also recognized in comparisons under the same distance from the quench front. Since the same tendencies can be predicted in the analyses with REFLA code because of the lower steam generation rate below quench front in the high subcooling test, the differences in the tests are supposed to be caused by the same reason. (2) Higher the subcooling gave larger amount of water accumulation in upper plenum. The carry-over liquid mass into hot leg became smaller in the later period in the higher subcooling test. These differences for carry-over and de-entrainment characteristics can be explained by the differences of quench velocity and of steam mass flow rate generated in the core. (3) No significant influence of the different degree of the subcooling was observed on the two-dimensional thermal-hydraulic behaviors in the pressure vessel. Namely, radial differences of sectional void fraction, heat transfer coefficient and the pressure among bundles at the same elevation were almost the same amount for the two tests. Radial differences of liquid levels in the upper plenum was also almost the same amount for the two tests. (J.P.N.)

Study of surface layer on 08Kh15N5D2T steel

International Nuclear Information System (INIS)

Tyurin, A.G.; Povolotskij, V.D.; Zhivotovskij, Eh.A.; Berg, B.N.

1986-01-01

08Kh15N5D2T steel phase composition is investigated. Its surface layer was determined by X-ray diffraction analysis method. It is shown, that a subscale appears to be the reason for corrosion of products, made of EhP410 steel. Under the existing smelling technology the carbon content in it is ≥ 0.05%. Therefore to avoid the metal surface depletion with chromium, one must provide for titanium relation to carbon of not less than 4.5 and carry out the rolled product thermal treatment in a protective atmosphere; otherwise, the technology must include not only the removal of scale from steel but the metal subscale layer as well

Effect of pressure on photo-induced expansion of As0.2Se0.8 layer

International Nuclear Information System (INIS)

Charnovych, S.; Kokenyesi, S.; Erdelyi, G.; Csik, A.

2011-01-01

Complete text of publication follows. Amorphous chalcogenide glasses are well known as materials where different kinds of structure-related transformations, like amorphysation-crystallization, volume and chemical stability changes take place under certain external influences (heat-, light-, and electric field). In spite of a rather long history of investigations and even some important applications in memory devices the mechanism of these effects is not completely clear, since besides the necessary condition of light interaction with glass and charge generation of the mass transport, shift or diffusion of atoms must occur. Unfortunately, we have only very little information about the light induced atomic transport processes in amorphous chalcogenides. Recent investigations on light-induced expansion, and holographic recording in chalcogenide glasses show that As 0.2 Se 0.8 composition reveals giant photo-expansion and photoplasticity effects. We selected this material for more detailed investigations of the direct relief formation process. In this work we investigate the influence of hydrostatic pressure on photo-stimulated surface relief formation in As 0.2 Se 0.8 thin films. 1 μm tick layers were evaporated from bulk glassy materials. Silica glass plates were used as substrate for films. The thickness of the layers were measured with profilometer type Ambios XP-I. The samples were illuminated with red laser beam (633 nm, output power P=7.5mW) through a copper grid, which resulted to an imprint picture on the surface of the film with interference fringes at the edges. In this way surface relief with different heights were formed after the given exposure according to the distribution of light intensity. The measurements were carried out at room temperature in a large-volume (1 cm 3 ) optical cell having sapphire windows. The hydrostatic pressure was generated by means of a 3-stage gas compressor. We used profilometer as well as scanning electron- and atomic force

Oxygen and minority carrier lifetimes in N-and P-type AL0.2GA0.8AS grown by metal organics vapor phase epitaxy

International Nuclear Information System (INIS)

Zahraman, Khaled; Leroux, M.; Gibart, P.; Zaidi, M.A.; Bremond, G.; Guillot, G.

2000-01-01

author.The minority carrier lifetimes in Al x Ga 1-x As grown by Metal-Organics Vapor Phase Epitaxy (MOVPE) is generally lower than in GaAs. This is believed to be due to oxygen incorporation in the layers. We describe a study of radiative and non radiative minority carriers lifetimes in n-and p-type Al 0.2 Ga 0.8 As as a function of growth parameters, in correlation with oxygen concentration measurements and deep level transient spectroscopy (DLTS) studies. Long non radiative lifetimes and low oxygen contents are achieved using temperature growth. A main minority hole lifetime killer appears to be 0.4 eV deep O related electron trap detected by DLTS at concentrations three orders of magnitude lower than the atomic oxygen one. Record lifetimes in MOVPE grown n-and p-type Al 0.2 Ga 0.8 As are obtained. An Al 0.85 Ga 0.15 As/Al 0.2 Ga 0.8 As surface recombination velocity lower than 4.5x10 3 cm.s -1 is measured

Results For The Third Quarter Calendar Year 2016 Tank 50H Salt Solution Sample

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2016-10-13

In this memorandum, the chemical and radionuclide contaminant results from the Third Quarter Calendar Year 2016 (CY16) sample of Tank 50H salt solution are presented in tabulated form. The Third Quarter CY16 Tank 50H samples (a 200 mL sample obtained 6” below the surface (HTF-5-16-63) and a 1 L sample obtained 66” from the tank bottom (HTF-50-16-64)) were obtained on July 14, 2016 and received at Savannah River National Laboratory (SRNL) on the same day. Prior to obtaining the samples from Tank 50H, a single pump was run at least 4.4 hours, and the samples were pulled immediately after pump shut down. The information from this characterization will be used by Defense Waste Processing Facility (DWPF) & Saltstone Facility Engineering for the transfer of aqueous waste from Tank 50H to the Saltstone Production Facility, where the waste will be treated and disposed of in the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the Task Technical and Quality Assurance Plan (TTQAP) for the Tank 50H saltstone task. The chemical and radionuclide contaminant results from the characterization of the Third Quarter CY16 sampling of Tank 50H were requested by Savannah River Remediation (SRR) personnel and details of the testing are presented in the SRNL TTQAP.

Residual mercury content and leaching of mercury and silver from used amalgam capsules.

Science.gov (United States)

Stone, M E; Pederson, E D; Cohen, M E; Ragain, J C; Karaway, R S; Auxer, R A; Saluta, A R

2002-06-01

The objective of this investigation was to carry out residual mercury (Hg) determinations and toxicity characteristic leaching procedure (TCLP) analysis of used amalgam capsules. For residual Hg analysis, 25 capsules (20 capsules for one brand) from each of 10 different brands of amalgam were analyzed. Total residual Hg levels per capsule were determined using United States Environmental Protection Agency (USEPA) Method 7471. For TCLP analysis, 25 amalgam capsules for each of 10 brands were extracted using a modification of USEPA Method 1311. Hg analysis of the TCLP extracts was done with USEPA Method 7470A. Analysis of silver (Ag) concentrations in the TCLP extract was done with USEPA Method 6010B. Analysis of the residual Hg data resulted in the segregation of brands into three groups: Dispersalloy capsules, Group A, retained the most Hg (1.225 mg/capsule). These capsules were the only ones to include a pestle. Group B capsules, Valliant PhD, Optaloy II, Megalloy and Valliant Snap Set, retained the next highest amount of Hg (0.534-0.770 mg/capsule), and were characterized by a groove in the inside of the capsule. Group C, Tytin regular set double-spill, Tytin FC, Contour, Sybraloy regular set, and Tytin regular set single-spill retained the least amount of Hg (0.125-0.266 mg/capsule). TCLP analysis of the triturated capsules showed Sybraloy and Contour leached Hg at greater than the 0.2 mg/l Resource Conservation and Recovery Act (RCRA) limit. This study demonstrated that residual mercury may be related to capsule design features and that TCLP extracts from these capsules could, in some brands, exceed RCRA Hg limits, making their disposal problematic. At current RCRA limits, the leaching of Ag is not a problem.

Potential Degradation of Swainsonine by Intracellular Enzymes of Arthrobacter sp. HW08

Directory of Open Access Journals (Sweden)

Haili Li

2013-11-01

Full Text Available Swainsonine (SW is a toxin produced by locoweeds and harmful to the livestock industry. Degrading SW by Arthrobacter sp. HW08 was demonstrated as a promising way to deal with SW poisoning. However, it is unknown which part of the subcellular enzymes in Arthrobacter sp. HW08 is responsible for biodegrading SW and whether the metabolites are atoxic. In this study, intracellular and extracellular enzymes of Arthrobacter sp. HW08 were isolated and their enzyme activity was evaluated. The metabolites were fed to mice, and physiological and histological properties of the treated mice were investigated. The results showed that only intracellular enzyme of Arthrobacter sp. HW08 (IEHW08 could degrade SW efficiently. Compared with mice in SW treatment group, mice in SW + IEHW08 treatment group (1 increased their body weights; (2 showed higher number of platelets and lower number of white blood cells; (3 decreased the levels of creatinine, urea nitrogen, alanine transaminase and aspartate aminotransferase in serum; (4 reduced the number of vacuolated cells in cerebellum, liver and kidney. All these data demonstrate that IEHW08 was potentially safe for mice, while keeping the capacity of degrading SW. This study indicates a possible application of IEHW08 as an additive in the livestock industry to protect animals from SW poisoning.

Size effect on the magnetic properties of antiferromagnetic La0.2Ca0.8MnO3 nanoparticles

Science.gov (United States)

Markovich, V.; Fita, I.; Wisniewski, A.; Mogilyansky, D.; Puzniak, R.; Titelman, L.; Martin, C.; Gorodetsky, G.

2010-03-01

Magnetic properties of electron-doped La0.2Ca0.8MnO3 manganite nanoparticles with average particle size ranging from 15 to 37 nm, prepared by the glycine-nitrate method, have been investigated in temperature range 5-300 K and in magnetic fields up to 90 kOe. A monotonous enhancement of weak ferromagnetism linked to the reduction in the particle size was observed for all nanoparticles. Magnetic hysteresis loops also indicate size-dependent exchange bias effect displayed by horizontal and vertical shifts in field-cooled processes. The magnetization data reveal two ferromagnetic components: first one appears at T˜200K and may be attributed to surface magnetization and second one appears as a result of spin canting of antiferromagnetic core or is developed at some interfaces inside nanoparticles. Time evolution of magnetization recorded in magnetic fields after the field cooling to low temperatures exhibits a very noisy behavior that may be caused by formation of collective state of nanoparticles with no clear tendency to reach equilibrium state. Magnetic properties of the nanoparticle samples are compared with those of the bulk La0.2Ca0.8MnO3 .

Internet-based interface for STRMDEPL08

Science.gov (United States)

Reeves, Howard W.; Asher, A. Jeremiah

2010-01-01

The core of the computer program STRMDEPL08 that estimates streamflow depletion by a pumping well with one of four analytical solutions was re-written in the Javascript software language and made available through an internet-based interface (web page). In the internet-based interface, the user enters data for one of the four analytical solutions, Glover and Balmer (1954), Hantush (1965), Hunt (1999), and Hunt (2003), and the solution is run for constant pumping for a desired number of simulation days. Results are returned in tabular form to the user. For intermittent pumping, the interface allows the user to request that the header information for an input file for the stand-alone executable STRMDEPL08 be created. The user would add the pumping information to this header information and run the STRMDEPL08 executable that is available for download through the U.S. Geological Survey. Results for the internet-based and stand-alone versions of STRMDEPL08 are shown to match.

Band alignment of atomic layer deposited MgO/Zn{sub 0.8}Al{sub 0.2}O heterointerface determined by charge corrected X-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Yan, Baojun, E-mail: yanbj@ihep.ac.cn [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics of Chinese Academy of Sciences, Beijing P. O. Box 100049 (China); Liu, Shulin [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics of Chinese Academy of Sciences, Beijing P. O. Box 100049 (China); Yang, Yuzhen [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics of Chinese Academy of Sciences, Beijing P. O. Box 100049 (China); Department of Physics, Nanjing University, Nanjing P. O. Box 210093 (China); Heng, Yuekun [State Key Laboratory of Particle Detection and Electronics, Institute of High Energy Physics of Chinese Academy of Sciences, Beijing P. O. Box 100049 (China)

2016-05-15

Highlights: • Band alignment of MgO/Zn{sub 0.8}Al{sub 0.2}O heterojunction were investigated systematically using charge corrected X-ray photoelectron spectroscopy. • Differential charging phenomenon is observed in determination VBOs of insulator/semiconductor heterojunction. • Valence and conduction band offsets have been determined to be 0.72 ± 0.11 eV and 3.26 ± 0.11 eV, respectively, with a type-II band line-up. - Abstract: Pure magnesium (MgO) and zinc oxide doped with aluminum oxide (Zn{sub 0.8}Al{sub 0.2}O) were prepared via atomic layer deposition. We have studied the structure and band gap of bulk Zn{sub 0.8}Al{sub 0.2}O material by X-ray diffractometer (XRD) and Tauc method, and the band offsets and alignment of atomic layer deposited MgO/Zn{sub 0.8}Al{sub 0.2}O heterointerface were investigated systematically using X-ray photoelectron spectroscopy (XPS) in this study. Different methodologies, such as neutralizing electron gun, the use of C 1s peak recalibration and zero charging method, were applied to recover the actual position of the core levels in insulator materials which were easily influenced by differential charging phenomena. Schematic band alignment diagram, valence band offset (ΔE{sub V}) and conduction band offset (ΔE{sub C}) for the interface of the MgO/Zn{sub 0.8}Al{sub 0.2}O heterostructure have been constructed. An accurate value of ΔE{sub V} = 0.72 ± 0.11 eV was obtained from various combinations of core levels of heterojunction with varied MgO thickness. Given the experimental band gaps of 7.83 eV for MgO and 5.29 eV for Zn{sub 0.8}Al{sub 0.2}O, a type-II heterojunction with a ΔE{sub C} of 3.26 ± 0.11 eV was found. Band offsets and alignment studies of these heterojunctions are important for gaining deep consideration to the design of various optoelectronic devices based on such heterointerface.

Polarization properties of La0.6Sr0.4Co0.2Fe0.8O3-based double layer-type oxygen electrodes for reversible SOFCs

International Nuclear Information System (INIS)

Tao, Y.; Nishino, H.; Ashidate, S.; Kokubo, H.; Watanabe, M.; Uchida, H.

2009-01-01

We have developed double layer-type (catalyst layer/current collecting layer) oxygen electrodes (DLE) for reversible SOFCs. As the catalyst layer (cathode for SOFC and anode for steam electrolysis) interfaced with a samaria-doped ceria [(CeO 2 ) 0.8 (SmO 1.5 ) 0.2 , SDC] interlayer/YSZ solid electrolyte, mixed conducting La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) and SDC particles were employed. The current collecting porous LSCF layer was formed on the catalyst layer. By controlling the SDC content, as well as the thickness and porosity of the catalyst layer, the gas diffusion rate and the conduction networks for electrons and oxide ions were optimized, resulting in a marked reduction of the overpotential. The LSCF + SDC/LSCF DLE exhibited higher performance than single-layer electrodes of LSCF + SDC or LSCF; the IR-free anode potential vs. an air reference electrode was 0.12 V (corresponding to an overpotential of 0.08 V) at 0.5 A cm -2 and 900 deg. C under an atmosphere of O 2 (1 atm)

21 CFR 1310.08 - Excluded transactions.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Excluded transactions. 1310.08 Section 1310.08 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RECORDS AND REPORTS OF LISTED...) Colombia (6) Ecuador (7) French Guiana (8) Guyana (9) Panama (10) Paraguay (11) Peru (12) Suriname (13...

INTERNATIONAL PROGRAM: SUMMARY REPORT ON THE PROPERTIES OF CEMENTITIOUS WASTE FORMS

International Nuclear Information System (INIS)

Harbour, J

2007-01-01

-9 cm 2 /sec and a corresponding leaching index of ∼8.2. Leaching tests at the lower bound of concentration and the leaching tests to determine the impact of redox (selenium exists in two oxidation states, selenite (SeO 3 -2 ) and selenate (SeO 4 -2 )) on Se-79 release were not completed due to lack of funding. The heat of hydration of a Saltstone mix limits the processing rate at the Saltstone Production Facility. Therefore, reduction in the heat of hydration of a Saltstone formulation that still complies with the remaining property requirements would provide for a greater rate of production. Initial testing for this task was completed. There was good agreement between the isothermal measurements of heat of hydration performed as part of this task with previous measurements of heat of hydration of Saltstone obtained adiabatically over the same 80 hour time period. The slightly higher heat of hydration per gram of cementitious material measured adiabatically can be explained by the higher temperatures achieved during the adiabatic measurements. The isothermal measurements reveal additional details of the heat generation process that were not evident in the adiabatic measurements. An initial heat release in the first minutes was observed isothermally. A second peak at about 5 hours was also observed isothermally that was not detected adiabatically. The major heat releases in the 10 to 30 hour period were observed by both techniques but at slightly different times and ratios of the two major peaks that comprise that region. The degree of reaction was calculated from these measurements based upon the value assigned to maximum hydration. Using the Schmidt method, the degree of reaction after 80 hours was 36% complete by isothermal calorimetry and 46% complete by adiabatic calorimetry. Using the theoretical maximum wherein the fly ash and slag are hydraulically equivalent to the portland cement, the degree of reaction after 80 hours was 20% complete by isothermal

The nonlinear optical properties of a magneto-exciton in a strained Ga0.2In0.8As/GaAs quantum dot

International Nuclear Information System (INIS)

Kumar, N. R. Senthil; Peter, A. John; Yoo Chang Kyoo

2013-01-01

The magnetic field-dependent heavy hole excitonic states in a strained Ga 0.2 In 0.8 As/GaAs quantum dot are investigated by taking into account the anisotropy, non-parabolicity of the conduction band, and the geometrical confinement. The strained quantum dot is considered as a parabolic dot of InAs embedded in a GaAs barrier material. The dependence of the effective excitonic g-factor as a function of dot radius and the magnetic field strength is numerically measured. The interband optical transition energy as a function of geometrical confinement is computed in the presence of a magnetic field. The magnetic field-dependent oscillator strength of interband transition under the geometrical confinement is studied. The exchange enhancements as a function of dot radius are observed for various magnetic field strengths in a strained Ga 0.2 In 0.8 As/GaAs quantum dot. Heavy hole excitonic absorption spectra, the changes in refractive index, and the third-order susceptibility of third-order harmonic generation are investigated in the Ga 0.2 In 0.8 As/GaAs quantum dot. The result shows that the effect of magnetic field strength is more strongly dependent on the nonlinear optical property in a low-dimensional semiconductor system. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Evaluación de los modelos de predicción del ACI-08, Eurocódigo 2 y EHE-08, para estimar las propiedades mecánicas del hormigón autocompactante

Directory of Open Access Journals (Sweden)

Agranati, G.

2010-12-01

Full Text Available The objective of this study is to evaluate the applicability of the ACI-08, EC-2, and EHE-08 models for the estimating of the mechanical properties of self-compacting concrete (SCC. The mechanical properties considered are the modulus of elasticity, tensile strength, and modulus of rupture. In order to statistically evaluate the applicability of the models it was necessary to compile an extensive database that included the experimental results for the various mechanical properties analyzed and the exact dosifications of the mixtures. The first part of the study includes an analysis of each one of the models, together with a regression analysis in order to evaluate the behavior and the adaptability to the different models. The specific characterization parameters for each concrete mixture were used to calculate the various mechanical properties applying the different estimation models. The second part of the analysis consisted in comparing the experimental results with the estimated results for all the mixtures in order to evaluate the applicability of these models to SCC.

El presente trabajo de investigación tiene como finalidad estudiar la aplicabilidad de los modelos de cálculo del ACI-08, Eurocódigo 2 y de la EHE-08 utilizados para la estimar las propiedades mecánicas del hormigón convencional, en el hormigón autocompactante. Las propiedades mecánicas estudiadas han sido: el módulo de deformación, la resistencia a tracción y la resistencia a flexotracción. Para llevar a cabo la investigación fue necesario construir una extensa base de datos que permitiera albergar en ella una gran cantidad de dosificaciones de hormigón autocompactante y un amplio rango de valores de sus propiedades mecánicas para lograr una muestra lo más representativa posible. En primera instancia se comparó el comportamiento de cada uno de estos modelos normativos de cálculo, con la curva de regresión de los datos obtenidos para el hormig

In situ growth and characterization of La{sub 0.8}Sr{sub 0.2}CoO{sub 3} perovskite mixed conductor films

Energy Technology Data Exchange (ETDEWEB)

Brosha, E.L.; Chung, B.W.; Garzon, F.H.; Raistrick, I.D.; Houlton, R.J.; Hawley, M.E. [Los Alamos National Lab., NM (United States)

1995-05-01

The authors have grown thin films of La{sub 0.8}Sr{sub 0.2}CoO{sub 3} on SrTiO{sub 3} [100], MgO [100], yttrium-stabilized zirconia YSZ [100], and CeO{sub 2} [100]/Al{sub 2}O{sub 3} substrates by using a 90{degree} off-axis RF magnetron sputtering deposition. X-ray diffraction analysis reveals that, depending on substrate, the deposited films grew either epitaxially or highly textured. Scanning tunneling microscopy reveals that the thin films grow with a smooth surface and with different growth mechanisms according to substrate. For La{sub 0.8}Sr{sub 0.2}CoO{sub 3} thin films grown on MgO [100], the low values of the channeling minimum yield from Rutherford backscattering spectroscopy indicated excellent epitaxy with the substrate. Thin films of perovskite materials are among the major focal research areas for optical, sensor, electronic, and superconducting applications.

Correlating thermoelectric properties with microstructure in Bi0.8Sb0.2 thin films

Science.gov (United States)

Siegal, M. P.; Lima-Sharma, A. L.; Sharma, P. A.; Rochford, C.

2017-04-01

The room temperature electronic transport properties of 100 nm-thick thermoelectric Bi0.8Sb0.2 films, sputter-deposited onto quartz substrates and post-annealed in an ex-situ furnace, systematically correlate with the overall microstructural quality, improving with increasing annealing temperature until close to the melting point for the alloy composition. The optimized films have high crystalline quality with ˜99% of the grains oriented with the trigonal axis perpendicular to the substrate surface. Film resistivities and Seebeck coefficients are accurately measured by preventing deleterious surface oxide formation via a SiN capping layer and using Nd-doped Al for contacts. The resulting values are similar to single crystals and significantly better than previous reports from films and polycrystalline bulk alloys.

Structural, optical and vibrational studies of Na{sup +} doped Cd{sub 0.8}Zn{sub 0.2}S semiconductor compounds

Energy Technology Data Exchange (ETDEWEB)

Yellaiah, G., E-mail: johngolluri@yahoo.com; Hadasa, K.; Nagabhushanam, M., E-mail: mamidala_nb@yahoo.com

2013-12-25

Graphical abstract: FTIR spectra of Cd{sub 0.8}Zn{sub 0.2}S: N{sub x} (x = 0.2 mol%). Highlights: •The energy band gaps of Cd{sub 0.8}Zn{sub 02}S: Nasamples were estimated. •Density and porosity percentages were calculated. •From the FTIR study CdS and ZnS stretching bonds were detected. -- Abstract: Cd{sub 0.8}Zn{sub 0.2}S semiconductor powders doped with different amounts of sodium have been synthesized by controlled co-precipitation technique. X-ray diffraction (XRD), Scanning electron microscope (SEM), Optical absorption and Fourier transform infrared spectroscope (FTIR) studies have been done on all these samples. XRD studies have revealed that the samples are polycrystalline with an average crystallite size ranging from 29 to 55 nm and they crystallize in the hexagonal form with wurtzite structure. The optical measurements revealed that the samples possess direct band gap and the band gap increases with an increase in the dopant concentration. The vibrational modes of Cd–S and Zn–S were obtained from FTIR studies and found to be at 812–618 cm{sup −1} respectively. Experimental and theoretical (XRD) densities were calculated and analyzed. Density from XRD and porosity in percentage varied from 92% to 94% and 5% to 8% respectively. The elemental analysis of the compounds was done by energy dispersive spectroscopy (EDS) and found that the cadmium, zinc, sulphur and sodium elements were present in the compound as per the composition taken. From the theoretical estimations it is understood that the dopant (Na) occupies the interstitial of CdZnS.

NCBI nr-aa BLAST: CBRC-PTRO-08-0058 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-PTRO-08-0058 ref|NP_009060.2| zinc finger protein of the cerebellum 2 [Homo sa...piens] sp|O95409|ZIC2_HUMAN Zinc finger protein ZIC 2 (Zinc finger protein of the cerebellum 2) gb|AAG28409....1|AF193855_1 zinc finger protein of cerebellum ZIC2 [Homo sapiens] emb|CAH70367.1| Zic family member 2 (odd-

40 CFR 600.006-08 - Data and information requirements for fuel economy vehicles.

Science.gov (United States)

2010-07-01

... controller, battery configuration, or other components performed within 2,000 miles prior to fuel economy... fuel economy vehicles. 600.006-08 Section 600.006-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel...

Thermophysical Properties and Structural Transition of Hg(0.8)Cd(0.2)Te Melt

Science.gov (United States)

Li, C.; Scripa, R. N.; Ban, H.; Lin, B.; Su, C.; Lehoczky, S. L.

2004-01-01

Thermophysical properties, namely, density, viscosity, and electrical conductivity of Hg(sub o.8)Cd(sub 0.2)Te melt were measured as a function of temperature. A pycnometric method was used to measure the melt density in the temperature range of 1072 to 1122 K. The viscosity and electrical conductivity were simultaneously determined using a transient torque method from 1068 to 1132 K. The density result from this study is within 0.3% of the published data. However, the current viscosity result is approximately 30% lower than the existing data. The electrical conductivity of Hg(sub o.8)Cd(sub 0.2)Te melt as a function of temperature, which is not available in the literature, is also determined. The analysis of the temperature dependent electrical conductivity and the relationship between the kinematic viscosity and density indicated that the structure of the melt appeared to be homogeneous when the temperature was above 1090 K. A structural transition occurred in the Hg(sub 0.8)Cd(0.2)Te melt as the temperature was decreased from 1090 K to the liquidus temperature.

A CONSISTENT STUDY OF METALLICITY EVOLUTION AT 0.8 < z < 2.6

Energy Technology Data Exchange (ETDEWEB)

Wuyts, Eva; Kurk, Jaron; Förster Schreiber, Natascha M.; Genzel, Reinhard; Wisnioski, Emily; Bandara, Kaushala; Wuyts, Stijn; Beifiori, Alessandra; Bender, Ralf; Buschkamp, Peter; Chan, Jeffrey; Davies, Ric; Eisenhauer, Frank; Fossati, Matteo; Kulkarni, Sandesh K.; Lang, Philipp [Max-Planck-Institut für extraterrestrische Physik, Giessenbachstr. 1, D-85741 Garching (Germany); Brammer, Gabriel B. [Space Telescope Science Institute, Baltimore, MD 21218 (United States); Burkert, Andreas [Universitäts-Sternwarte München, Scheinerstr. 1, D-81679 München (Germany); Carollo, C. Marcella; Lilly, Simon J., E-mail: evawuyts@mpe.mpg.de [Institute of Astronomy, Department of Physics, Eidgensösische Technische Hochschule, ETH Zürich, CH-8093 (Switzerland); and others

2014-07-10

We present the correlations between stellar mass, star formation rate (SFR), and the [N II]/Hα flux ratio as an indicator of gas-phase metallicity for a sample of 222 galaxies at 0.8 < z < 2.6 and log (M {sub *}/M {sub ☉}) = 9.0-11.5 from the LUCI, SINS/zC-SINF, and KMOS{sup 3D} surveys. This sample provides a unique analysis of the mass-metallicity relation (MZR) over an extended redshift range using consistent data analysis techniques and a uniform strong-line metallicity indicator. We find a constant slope at the low-mass end of the relation and can fully describe its redshift evolution through the evolution of the characteristic turnover mass where the relation begins to flatten at the asymptotic metallicity. At a fixed mass and redshift, our data do not show a correlation between the [N II]/Hα ratio and SFR, which disagrees with the 0.2-0.3 dex offset in [N II]/Hα predicted by the ''fundamental relation'' between stellar mass, SFR, and metallicity discussed in recent literature. However, the overall evolution toward lower [N II]/Hα at earlier times does broadly agree with these predictions.

Aerosol deposition of Ba0.8Sr0.2TiO3 thin films

Directory of Open Access Journals (Sweden)

Branković Zorica

2009-01-01

Full Text Available In this work we optimized conditions for aerosol deposition of homogeneous, nanograined, smooth Ba0.8Sr0.2TiO3 thin films. Investigation involved optimization of deposition parameters, namely deposition time and temperature for different substrates. Solutions were prepared from titanium isopropoxide, strontium acetate and barium acetate. Films were deposited on Si (1 0 0 or Si covered by platinum (Pt (1 1 1 /Ti/SiO2/Si. Investigation showed that the best films were obtained at substrate temperature of 85ºC. After deposition films were slowly heated up to 650ºC, annealed for 30 min, and slowly cooled. Grain size of BST films deposited on Si substrate were in the range 40-70 nm, depending on deposition conditions, while the same films deposited on Pt substrates showed mean grain size in the range 35-50 nm. Films deposited under optimal conditions were very homogeneous, crackfree, and smooth with rms roughness lower than 4 nm for both substrates.

A Special Extract of Bacopa monnieri (CDRI-08-Restored Memory in CoCl2-Hypoxia Mimetic Mice Is Associated with Upregulation of Fmr-1 Gene Expression in Hippocampus

Directory of Open Access Journals (Sweden)

Anupama Rani

2015-01-01

Full Text Available Fragile X mental retardation protein (FMRP is a neuronal translational repressor and has been implicated in learning, memory, and cognition. However, the role of Bacopa monnieri extract (CDRI-08 in enhancing cognitive abilities in hypoxia-induced memory impairment via Fmr-1 gene expression is not known. Here, we have studied effects of CDRI-08 on the expression of Fmr-1 gene in the hippocampus of well validated cobalt chloride (CoCl2-induced hypoxia mimetic mice and analyzed the data with alterations in spatial memory. Results obtained from Morris water maze test suggest that CoCl2 treatment causes severe loss of spatial memory and CDRI-08 is capable of reversing it towards that in the normal control mice. Our semiquantitative RT-PCR, Western blot, and immunofluorescence microscopic data reveal that CoCl2-induced hypoxia significantly upregulates the expression of Hif-1α and downregulates the Fmr-1 expression in the hippocampus, respectively. Further, CDRI-08 administration reverses the memory loss and this is correlated with significant downregulation of Hif-1α and upregulation of Fmr-1 expression. Our data are novel and may provide mechanisms of hypoxia-induced impairments in the spatial memory and action of CDRI-08 in the recovery of hypoxia led memory impairment involving Fmr-1 gene encoded protein called FMRP.

NCBI nr-aa BLAST: CBRC-DMEL-08-0002 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0002 ref|XP_001545568.1| predicted protein [Botryotinia fuckeliana B05....10] gb|EDN23745.1| predicted protein [Botryotinia fuckeliana B05.10] XP_001545568.1 2e-40 85% ...

NCBI nr-aa BLAST: CBRC-DMEL-08-0035 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0035 ref|XP_001545568.1| predicted protein [Botryotinia fuckeliana B05....10] gb|EDN23745.1| predicted protein [Botryotinia fuckeliana B05.10] XP_001545568.1 2e-40 85% ...

Effect of Manganese Addition on the Structure, Magnetic Properties and Microwave Absorption of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3

Science.gov (United States)

Adi, W. A.; Indro, M. N.; Kusumastuti, A. A.

2017-03-01

We have carried out modification of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 (x = 0.1 - 0.8) magnetic materials by wet milling method. Raw materials of La2O3, BaCO3, Fe2O3, TiO2 and MnCO3 were mixed according to stoichiometry calculation for each composition. The mixture was milled for 5 hours and then sintered at 1000 °C for 5 hours. The refinement results by X-ray diffraction pattern shows that the increasing Mn composition enhances the mass fraction of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 phase which has the same structure as LaMnO3. For x = 0.8 a single phase of LaMnO3 was formed. The single phase has a crystal monoclinic crystal structure with space group of I 1 2 / a 1, with lattice parameters given by a = 5.519(5) Å, b = 5.5537(5) Å and c = 7.8176(9) Å, α = γ = 90o and β = 90.345(6)o, V = 239.64(3) Å3, ρ = 6.463 gr.cm-3, wRp = 5.96, and χ2 (chi-squared) = 1.17. The hysteresis curve shows that the sample with composition x = 0.8 produces ferromagnetic behaviour at room temperature. The ferromagnetic properties arise due to the mixed valence of Mn3+ and Mn4+ ions through a double exchange mechanism. The results of the microwave absorption indicated that there was a broadening of absorption peak frequency at 9.9 GHz. The reflection loss (RL) increases with the increasing of LaMnO3 phase. For x = 0.8 we have the best of RL where the microwave absorption was calculated reaching 95% at the highest peak frequency with a thickness of 1.5 mm. Thus we have been successful in creating a single phase of La0.8Ba0.2MnxFe½(1-x)Ti½(1-x)O3 with application as a microwave absorber.

Microscopic Structure of DX Centers in Cd0.8Zn0.2Te:Cl

International Nuclear Information System (INIS)

Shan, Y.Y.; Lynn, K.G.; Szeles, C.; Asoka-Kumar, P.; Thio, T.; Bennett, J.W.; Beling, C.B.; Fung, S.; Becla, P.

1997-01-01

Photoexcitation of chlorine DX centers induces a transition of the Cl atoms to the shallow-donor state and persistent photoconductivity at low temperature in Cd 0.8 Zn 0.2 Te:Cl. The relaxation of the substitutional Cl atoms to the DX state at 140K is coincident with a decrease of the positron line-shape parameter and an increase of annihilation with high-momentum core electrons. The results indicate positron trapping and annihilation at DX centers and at chlorine A centers. The data support the bond breaking model of the DX centers and the outward relaxation of the Cl and Cd(Zn) atoms along the [111] direction. The thermal barrier for the shallow-deep transition was found to be 0.44eV. copyright 1997 The American Physical Society

Síntese e estudo microestrutural de perovsquitas tipo La0,8Ca0,2MO3 (M: Co e Mn para aplicação em catálise automotiva Synthesis and microstructural study of La0.8Ca0.2MO3 (M: Mn and Co perovskites for automotive catalysis

Directory of Open Access Journals (Sweden)

J. P. Ribeiro

2011-09-01

Full Text Available Materiais com estrutura perovsquita são potenciais catalisadores para prevenir a emissão de componentes indesejáveis ao meio ambiente. Diferentes métodos têm sido propostos para a síntese desses materiais, visando produzir materiais homogêneos com tamanho nanométrico de partículas. Os compostos La0,8Ca0,2MnO3 e La0,8Ca0,2CoO3 foram preparados pelo método dos precursores poliméricos visando sua utilização como catalisadores automotivos. Este método de síntese foi utilizado porque permite a obtenção de pós homogêneos e fases cristalinas a temperaturas mais baixas que os outros métodos tradicionais de síntese. Os materiais foram calcinados a 700 e 900 ºC por 4 h e caracterizados pelas técnicas de análise térmica, difração de raios X e microscopia eletrônica de varredura. As perovsquitas obtidas são nanométricas, monofásicas e com propriedades adequadas para utilização em catálise automotiva.Materials with perovskite structure are potential catalysts for preventing greenhouse gas emissions to the environment. Several methods have been proposed for the synthesis of these materials in order to produce homogeneous powders with nanometric particle size. In the present work, the La0.8Ca0.2MnO3 and La0.8Ca0.2CoO3 systems were prepared by the polymeric precursor method for application in automotive catalysis. This method was chosen because it allows obtaining homogeneous powders and crystalline phases at lower temperatures. The powders were calcined at 700 and 900 ºC for 4 h and characterized by thermal analysis, X-ray diffraction and scanning electron microscopy techniques. The perovskites are nanometric, single phased and present suitable properties for use in automotive catalysis.

Unigene BLAST: CBRC-DMEL-08-0015 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0015 gnl|UG|Dm#S40593121 DMG1C.2_1.G07.C1 MODENCODE_DM_A Drosophila melanogaster cDNA clone DMG...1-chr3R.3.082.a, mRNA sequence /clone=DMG1-chr3R.3.082.a /gb=EW713160 /gi=156142114 /ug=Dm.27906 /len=1533 4e-07 35% ...

Unigene BLAST: CBRC-DMEL-08-0038 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0038 gnl|UG|Dm#S40593121 DMG1C.2_1.G07.C1 MODENCODE_DM_A Drosophila melanogaster cDNA clone DMG...1-chr3R.3.082.a, mRNA sequence /clone=DMG1-chr3R.3.082.a /gb=EW713160 /gi=156142114 /ug=Dm.27906 /len=1533 6e-10 32% ...

Unigene BLAST: CBRC-DMEL-08-0039 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0039 gnl|UG|Dm#S40593121 DMG1C.2_1.G07.C1 MODENCODE_DM_A Drosophila melanogaster cDNA clone DMG...1-chr3R.3.082.a, mRNA sequence /clone=DMG1-chr3R.3.082.a /gb=EW713160 /gi=156142114 /ug=Dm.27906 /len=1533 4e-07 39% ...

Begonia semperflorens FB08-59 and FB08-163 clonal germplasm

Science.gov (United States)

FB08-59 is a dark-foliage, red-flowered wax begonia clone adapted to hot humid summers. It is the product of a recurrent selection breeding procedure to combine and improve the environmental tolerances identified in B. semperflorens ’Kaylen’ and B. cucullata arenosicola into a dark-foliaged, perenn...

NCBI nr-aa BLAST: CBRC-MDOM-08-0152 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0152 ref|NP_001074192.1| taste receptor, type 2, member 41 [Canis lupus... familiaris] dbj|BAE80338.1| bitter taste receptor [Canis lupus familiaris] NP_001074192.1 1e-108 63% ...

Variability Of KD Values In Cementitious Materials And Sediments

International Nuclear Information System (INIS)

Almond, P.; Kaplan, D.; Shine, E.

2012-01-01

Measured distribution coefficients (K d values) for environmental contaminants provide input data for performance assessments (PA) that evaluate physical and chemical phenomena for release of radionuclides from wasteforms, degradation of engineered components and subsequent transport of radionuclides through environmental media. Research efforts at SRNL to study the effects of formulation and curing variability on the physiochemical properties of the saltstone wasteform produced at the Saltstone Disposal Facility (SDF) are ongoing and provide information for the PA and Saltstone Operations. Furthermore, the range and distribution of plutonium K d values in soils is not known. Knowledge of these parameters is needed to provide guidance for stochastic modeling in the PA. Under the current SRS liquid waste processing system, supernate from F and H Tank Farm tanks is processed to remove actinides and fission products, resulting in a low-curie Decontaminated Salt Solution (DSS). At the Saltstone Production Facility (SPF), DSS is mixed with premix, comprised of blast furnace slag (BFS), Class F fly ash (FA), and portland cement (OPC) to form a grout mixture. The fresh grout is subsequently placed in SDF vaults where it cures through hydration reactions to produce saltstone, a hardened monolithic waste form. Variation in saltstone composition and cure conditions of grout can affect the saltstone's physiochemical properties. Variations in properties may originate from variables in DSS, premix, and water to premix ratio, grout mixing, placing, and curing conditions including time and temperature (Harbour et al. 2007; Harbour et al. 2009). There are no previous studies reported in the literature regarding the range and distribution of K d values in cementitious materials. Presently, the Savannah River Site (SRS) estimate ranges and distributions of K d values based on measurements of K d values made in sandy SRS sediments (Kaplan 2010). The actual cementitious material K d

Highly active La0.4Sr0.6Co0.8Fe0.2O3-δ nanocatalyst for oxygen reduction in intermediate temperature-solid oxide fuel cells

Science.gov (United States)

Chanquía, Corina M.; Mogni, Liliana; Troiani, Horacio E.; Caneiro, Alberto

2014-12-01

Pure-phase La0.4Sr0.6Co0.8Fe0.2O3-δ (LSCF) nanocrystallites were successfully synthesized by the combustion method, by employing glycine as fuel and complexing agent, and ammonium nitrate as combustion trigger. The morphological and structural characterization of the LSCF nanopowders was performed by using X-ray diffraction, N2 physisorption and electron microscopy. The LSCF nanopowder consists of interconnected nanocrystallites (∼45 nm) forming a sponge-like structure with meso and macropores, being its specific surface area around 10 m2 g-1. Crystalline structural analyses show that the LSCF nanopowder presents cubic symmetry in the Pm-3m space group. By employing the spin coating technique and different thermal treatments, symmetrical cells with different electrode crystallite size (45 and 685 nm) were built, by using La0.8Sr0.2Ga0.8Mg0.2O3-δ as electrolyte. Electrochemical impedance spectroscopy measurements were performed varying temperature and pO2. The area specific resistance of the nanostructured sample (45 nm) decreases by two orders of magnitude with respect to the submicrostructured sample (685 nm), reaching values as low as 0.8 Ω cm2 at 450 °C. This improvement is attributed to the cathode morphology optimization in the nanoscale, i.e., enlargement of the exposed surface area and shortening of the oxygen diffusion paths, which reduce the polarization resistance associated to the surface exchange and O-ion bulk diffusion process.

NCBI nr-aa BLAST: CBRC-GACU-08-0023 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-GACU-08-0023 ref|NP_001041562.1| prostaglandin F receptor (FP) [Canis lupus fa...miliaris] gb|AAZ53353.1| prostaglandin F2-alpha receptor [Canis lupus familiaris] NP_001041562.1 7e-91 47% ...

Physics at the FMQT'08 conference

Czech Academy of Sciences Publication Activity Database

Špička, Václav; Nieuwenhuizen, T.M.; Keefe, P.D.

2010-01-01

Roč. 42, č. 3 (2010), s. 207-227 ISSN 1386-9477. [International Conference on Frontiers of Quantum and Mesoscopic Thermodynamics (FQMT '08). Praha, 28.07.2008-02.08.2008] Institutional research plan: CEZ:AV0Z10100502 Keywords : foundations of quantum physics * quantum optics * quantum gases * quantum computing and information * thermodynamics Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.304, year: 2010

NCBI nr-aa BLAST: CBRC-MDOM-08-0147 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0147 ref|NP_001138970.1| bitter taste receptor Cafa-T2R39 [Canis lupus... familiaris] dbj|BAE80336.1| bitter taste receptor [Canis lupus familiaris] NP_001138970.1 1e-108 63% ...

NCBI nr-aa BLAST: CBRC-MDOM-08-0131 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MDOM-08-0131 ref|NP_001138971.1| bitter taste receptor Cafa-T2R3 [Canis lupus ...familiaris] dbj|BAE80329.1| bitter taste receptor [Canis lupus familiaris] NP_001138971.1 3e-69 47% ...

Effect of Ca substitution on the electrochemical properties of the Ruddlesden-Popper oxides Sr3.2-xCaxLn0.8Fe1.5Co1.5O10-δ

Science.gov (United States)

Padmasree, K. P.; Lai, Ke-Yu; Kaveevivitchai, Watchareeya; Manthiram, Arumugam

2018-01-01

The Ruddlesden-Popper (R-P) oxides Sr3.2-xCaxLn0.8Fe1.5Co1.5O10-δ with x = 0 and 0.4 and Ln = La, Pr, and Nd, have been synthesized and the effect of Ca on their electrochemical properties as cathodes in solid oxide fuel cells (SOFC) has been investigated. The substitution of Ca for Sr in Sr3.2-xCaxLn0.8Fe1.5Co1.5O10-δ decreases the amount of oxygen loss on heating and the thermal expansion coefficient (TEC). The phase instability of these materials at high temperature is a significant issue that restricts their application as SOFC cathodes, and the substitution of Ca effectively stabilizes the Sr3.2-xCaxLn0.8Fe1.5Co1.5O10-δ phase at 800 °C. Among the different lanthanides with and without Ca in Sr3.2-xCaxLn0.8Fe1.5Co1.5O10-δ, the Ln = Nd samples exhibit an enhancement in cathode performance in SOFC compared to Ln = La and Pr samples, which may be attributed to the higher concentration of oxygen vacancies in the Ln = Nd samples. Comparing the various compositions studied, the Sr2.8Ca0.4Nd0.8Fe1.5Co1.5O10-δ cathode material exhibits superior performance in SOFC with good phase stability.

Structural, magnetic and magnetocaloric properties of La{sub 0.8}Ca{sub 0.2−x}Na{sub x}MnO{sub 3} manganites (0≤x≤0.2)

Energy Technology Data Exchange (ETDEWEB)

Choura Maatar, S. [Laboratoire de Physique des Matériaux, Faculté des Sciences de Sfax, Sfax University, B.P. 1171, 3000 Sfax (Tunisia); M’nassri, R. [Laboratoire de Physique des Matériaux, Faculté des Sciences de Sfax, Sfax University, B.P. 1171, 3000 Sfax (Tunisia); Institut NEEL, CNRS, B.P.166, 38042 Grenoble Cedex 9 (France); Cheikhrouhou Koubaa, W., E-mail: wissem.koubaa@yahoo.fr [Laboratoire de Physique des Matériaux, Faculté des Sciences de Sfax, Sfax University, B.P. 1171, 3000 Sfax (Tunisia); Koubaa, M. [Laboratoire de Physique des Matériaux, Faculté des Sciences de Sfax, Sfax University, B.P. 1171, 3000 Sfax (Tunisia); Cheikhrouhou, A. [Laboratoire de Physique des Matériaux, Faculté des Sciences de Sfax, Sfax University, B.P. 1171, 3000 Sfax (Tunisia); Centre de Recherche en Informatique, Multimédia et Traitement Numérique des Données, Technopole de Sfax, Cité El Ons, Route de Tunis, Km 9, Sfax. B.P. 275, Sakiet Ezzit, 3021 Sfax (Tunisia)

2015-05-15

In this work, we report the effect of Na doping on the structural, magnetic and magnetocaloric properties in La{sub 0.8}Ca{sub 0.2−x}Na{sub x}MnO{sub 3} powder samples. Our polycristalline samples have been synthesized using the solid-state reaction method at high temperatures. The parent compound La{sub 0.8}Ca{sub 0.2}MnO{sub 3} crystallizes in the orthorhombic system with Pbnm space group. Na doping induces a structural transition from orthorhombic (Pbnm space group) to rhombohedral (R-3C space group) symmetry. Magnetization measurements versus temperature in a magnetic applied field of 50 mT showed that all our investigated samples display a paramagnetic-ferromagnetic transition with decreasing temperature. The Curie temperature T{sub C} increases with Na content from 240 K for x=0 to 330 K for x=0.2. A large magnetocaloric effect has been observed in all samples, the maximum entropy change, |∆S{sub M}|{sub max}, shifts to smaller values with increasing Na content, from4.56 J/kg K (x=0.05) to 2.3 J/kg K (x=0.2) under a magnetic field change ∆µ{sub 0}H of 2 T. For the same applied magnetic field of 2 T, the Relative Cooling Power (RCP) values are found to be constant around 91 J/kg. - Graphical abstract: Sodium doping induces an increase of T{sub C} from 240 K for x=0 to 330 K for x=0.2. - Highlights: • La{sub 0.8}Ca{sub 0.2−x}Na{sub x}MnO{sub 3} are synthesized using the ceramic method at high temperatures. • Na doping induces a structural transition from Pbnm to R-3C space group. • T{sub C} increases with Na content from 240 K for x=0 to 330 K for x=0.2. • RCP is constant around 91 J/kg for all compounds under 2 T.

Anomalous low temperature resistivity in CeCr0.8V0.2Ge3

Science.gov (United States)

Singh, Durgesh; Patidar, Manju Mishra; Mishra, A. K.; Krishnan, M.; Ganesan, V.

2018-04-01

Resistivity (8T) and heat capacity (0T) of CeCr0.8V0.2Ge3 at low temperatures and high magnetic fields are reported. Resistivity curve shows a Kondo like behavior at an anomalously high temperature of 250K. A broad peak at 20K is observed in resistivity. A sharp change in resistivity around 7.3K is due to magnetic ordering mediated by coherence effects. Similar low temperature peak is also observed in heat capacity around 7.2K. A small magnetic field of the order of 1T shifts the peak towards lower temperatures confirming the antiferromagnetic ordering. A broad feature, which appears in resistivity at 20K, is absent in heat capacity. This feature shift towards higher temperatures with magnetic field, and may be due to the partial ferromagnetic ordering or due to geometrical frustration which opposes the magnetic ordering. The system shows a moderate heavy fermion behavior with Sommerfeld coefficient (γ) of 111mJ/mol-K2. Debye temperature of the compound is 250K. Shifting of TN in magnetic fields towards 0K indicates a possibility of quantum criticality in this system.

Synthesis of Nano-Structured La0.6Sr0.4Co0.2Fe0.8O3 Perovskite by Co-Precipitation Method

Directory of Open Access Journals (Sweden)

Ebrahim Mostafavi

2015-06-01

Full Text Available Nano-structured lanthanum strontium cobalt ferrite, La0.6Sr0.4Co0.2Fe0.8O3 (LSCF, was successfully synthesized via co-precipitation method using metal nitrates as starting materials. Effects of precipitating agent and calcination temperature on the phase composition and morphology of synthesized powders were systematically studied using X-ray diffraction (XRD and field emission scanning electron microscopy (FESEM, respectively. XRD analysis revealed that a single phase La0.6Sr0.4Co0.2Fe0.8O3 perovskite was obtained in the processed sample using ammonium carbonate as precipitating agent with a NH4+/NO3-molar ratio of 2 after calcination at 1000C for 1 h. The phase composition of products was also affected by changing pH values. Moreover, using sodium hydroxide as a precipitant resulted in a mixture of La0.6Sr0.4Co0.2Fe0.8O3 and cobalt ferrite (CoFe2O4 phases. Careless washing of the precursors can also led to the formation of mixed phase after calcination of final powders. Mean crystallite size of the obtained powders was not noticeably affected by varying calcination temperature from 900 to 1050C and remained almost the same at 10 nm, however increasing calcination temperature to 1100C resulted in sharp structural coarsening. FESEM studies demonstrate that relatively uniform particles with mean particle size of 90 nm were obtained in the sample processed with a NH4+/NO3- molar ratio of 2 after calcination at 1000C for 1 h.

40 CFR 600.007-08 - Vehicle acceptability.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Vehicle acceptability. 600.007-08... FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for 1977 and Later Model Year Automobiles-General Provisions § 600.007-08 Vehicle acceptability. (a) All...

Properties and performance of BaxSr1-xCo0.8Fe0.2O3-d materials for oxygen transport membranes

NARCIS (Netherlands)

Vente, Jaap F.; McIntosh, S.; McIntosh, Steven; Haije, Wim G.; Bouwmeester, Henricus J.M.

2006-01-01

The present paper discusses the oxygen transport properties, oxygen stoichiometry, phase stability, and chemical and mechanical stability of the perovskites $${\\text{Ba}}_{{0.5}} {\\text{Sr}}_{{0.5}} {\\text{Co}}_{{0.8}} {\\text{Fe}}_{{0.2}} {\\text{O}}_{{3 - \\delta }} $$ (BSCF) and

Voltage-controlled ferroelastic switching in Pb(Zr.sub.0.2./sub.Ti.sub.0.8./sub.)O.sub.3./sub. thin films

Czech Academy of Sciences Publication Activity Database

Khan, A.I.; Martí, Xavier; Serrao, C.; Ramesh, R.; Salahuddin, S.

2015-01-01

Roč. 15, č. 4 (2015), s. 2229-2234 ISSN 1530-6984 Institutional support: RVO:68378271 Keywords : nanodomains * ferroelastic switching * ferroelectricity * Pb(Zr 0.2 Ti 0.8 )O 3 * thin film Subject RIV: BE - Theoretical Physics Impact factor: 13.779, year: 2015

In-plain electric properties of [CaMnO3/REMO3] (RE=Bi, La M=Fe, Fe0.8Mn0.2) superlattices grown by pulsed laser deposition method

NARCIS (Netherlands)

Iwata, N.; Watabe, Y.; Oikawa, T.; Takase, K.; Huijben, Mark; Inaba, T.; Oshima, K.; Rijnders, Augustinus J.H.M.; Yamamoto, H.

2014-01-01

The [CaMnO3 (CMO)/REMO3] (RE = Bi, La M = Fe, Fe0.8Mn0.2) superlattices show semiconducting behavior with transition temperatures (TEg) of 71, 127, and 151 K in the [CMO/BiFe0.8Mn0.2O3], [CMO/BiFeO3], and [CMO/LaFeO3] superlattices. The formation of a magnetic polaron is expected in the CMO layer of

Role of Cu2+ Concentration on the Microstructure and Gas Sensing Properties of Ni1-xCuxFe2O4 (0 ≤ x ≤ 0.8 Ferrite

Directory of Open Access Journals (Sweden)

Elena Rezlescu

2008-04-01

Full Text Available The microstructure and gas sensor properties of some nanostructured soft ferrites (Ni1-xCuxFe2O4, x = 0.2, 0.4, 0.6, 0.8 are studied. Using sol-gel self-combustion technology and subsequent heat treatment were prepared ferrite powders, having molecular scale homogeneity and nanosized granulation. The scanning electron microscopy (SEM was used to investigate morphology and pore structure. The effect of operating temperature and copper content on the fundamental features of a sensor element such as sensitivity and response time towards acetone, ethanol and LPG vapour has been studied. All samples are sensitive to ethanol and acetone and have a poor sensitivity to LPG. For a large copper content (x > 0.4 the electrical response to ethanol is larger than that to acetone, at the same working temperature, of 280oC. Among the investigated ferrites, Ni0,2Cu0,8Fe2O4 composition shows the best sensitivity to ethanol (about 70 % at operating temperature of 280ºC. The gas sensitivity increases with increasing gas concentration from 25 to 150 ppm, whereas the response time decreases.

NCBI nr-aa BLAST: CBRC-RMAC-08-0011 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RMAC-08-0011 ref|NP_005276.2| G protein-coupled receptor 7 [Homo sapiens] gb|AAH69117.1| Neuropeptides... B/W receptor 1 [Homo sapiens] gb|AAI07102.1| Neuropeptides B/W receptor 1 [Homo sap...iens] gb|EAW86722.1| neuropeptides B/W receptor 1 [Homo sapiens] NP_005276.2 1e-179 97% ...

NCBI nr-aa BLAST: CBRC-TGUT-08-0001 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-TGUT-08-0001 ref|NP_067250.2| potassium voltage-gated channel, shaker-related ...assium voltage-gated channel, shaker-related subfamily, member 4 [Mus musculus] emb|CAM23761.1| potassium voltage-gated channel, shak...4.1| potassium voltage-gated channel, shaker-related subfamily, member 4 [Mus musculus] NP_067250.2 0.0 79% ...

Results for the first quarter calendar year 2017 tank 50H salt solution sample

Energy Technology Data Exchange (ETDEWEB)

Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-04-12

In this memorandum, the chemical and radionuclide contaminant results from the First Quarter Calendar Year 2017 (CY17) sample of Tank 50H salt solution are presented in tabulated form. The First Quarter CY17 Tank 50H samples [a 200 mL sample obtained 6” below the surface (HTF-50-17-7) and a 1 L sample obtained 66” from the tank bottom (HTF-50-17-8)] were obtained on January 15, 2017 and received at Savannah River National Laboratory (SRNL) on January 16, 2017. Prior to obtaining the samples from Tank 50H, a single pump was run at least 4.4 hours and the samples were pulled immediately after pump shut down. All volatile organic analysis (VOA) and semi-volatile organic analysis (SVOA) were performed on the surface sample and all other analyses were performed on the variable depth sample. The information from this characterization will be used by Savannah River Remediation (SRR) for the transfer of aqueous waste from Tank 50H to the Saltstone Production Facility, where the waste will be treated and disposed of in the Saltstone Disposal Facility. This memorandum compares results, where applicable, to Saltstone Waste Acceptance Criteria (WAC) limits and targets. The chemical and radionuclide contaminant results from the characterization of the First Quarter CY17 sampling of Tank 50H were requested by SRR personnel and details of the testing are presented in the SRNL Task Technical and Quality Assurance Plan (TTQAP). This memorandum is part of Deliverable 2 from SRR request. Data pertaining to the regulatory limits for Resource Conservation and Recovery Act (RCRA) metals will be documented at a later time per the TTQAP for the Tank 50H saltstone task.

Evolution of E-centers during the annealing of Sb-doped Si0.8Ge0.2

DEFF Research Database (Denmark)

Kilpeläinen, S.; Tuomisto, F.; Slotte, J.

2011-01-01

Evolution of the chemical surroundings of vacancy complexes in Sb-doped ([Sb] = 2 × 1018 and 2 × 1019 cm−3) Si0.8Ge0.2 was studied with positron annihilation spectroscopy in Doppler broadening mode. The study was performed by annealing the samples both isochronally and isothermally. Defect...... evolution was observed at the temperature range 450–650 K. Both treatments were shown to induce changes in the chemical surroundings of the E-centers via introduction of Ge near the defects. Moreover, Sb was found to hinder these changes by stabilizing the E-centers and thus preventing them from finding Ge....... The stable state reached after the anneals was found to differ from that measured from an as-grown sample. This difference was deemed to be the result of Ge gathering in small clusters during the annealing thus breaking the initially random Ge distribution....

NCBI nr-aa BLAST: CBRC-HSAP-08-0029 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-HSAP-08-0029 ref|YP_001507265.1| hypothetical protein Franean1_2939 [Frankia s...p. EAN1pec] gb|ABW12359.1| hypothetical protein Franean1_2939 [Frankia sp. EAN1pec] YP_001507265.1 2.8 30% ...

A-Site Deficient (Pr0.6Sr0.4)(1-s)Fe0.8Co0.2O3-delta Perovskites as Solid Oxide Fuel Cell Cathodes

DEFF Research Database (Denmark)

Kammer Hansen, Kent

2009-01-01

Five A-site deficient (Pr0.6Sr0.4)1−sFe0.8Co0.2O3− perovskites (s=0.01, 0.05, 0.10, 0.15, and 0.20) were synthesized using the glycine-nitrate process. The perovskites were characterized with powder X-ray diffraction (XRD), dilatometry, four-point dc conductivity measurements, and electrochemical...... resistance more than 3 times lower than the weakly A-site deficient (Pr0.6Sr0.4)0.99Fe0.8Co0.2O3− perovskite. ©2009 The Electrochemical Society...

Oxygen partial pressure treatment of the electron-doped superconductor (Nd0.92Ce0.08)2CuO4-δ

International Nuclear Information System (INIS)

Suzuki, M.; Ami, T.; Isobe, M.; Tanaka, M.

1992-01-01

The condition under which the superconducting phase in (Nd 1-x Ce x ) 2 CuO 4-δ with x=0.08 is obtained was determined in the 1/T-log Po 2 phase diagram using an oxygen partial pressure (Po 2 ) controllable heat treatment system in conjunction with a quench system. The superconducting area is very narrow and is adjacent to the area of significant decomposition. We determined that the a-axis lattice constant increased slightly as the character of the electric conduction changed from semiconductive to metallic. (orig.)

Oxygen partial pressure treatment of the electron-doped superconductor (Nd0.92Ce0.08)2CuO4-δ

International Nuclear Information System (INIS)

Suzuki, M.; Ami, T.; Isobe, M.; Tanaka, M.

1992-01-01

The condition under which the superconducting phase in (Nd 1-x Ce x ) 2 CuO 4-δ with x = 0.08 is obtained was determined in the 1/T-log Po 2 phase diagram using an oxygen partial pressure (Po 2 ) controllable heat treatment system in conjunction with a quench system. The superconducting area is very narrow and is adjacent to the area of significant decomposition. In this paper, the authors determined that the a-axis lattice constant increased slightly as the character of the electric conduction changed from semiconductive to metallic

The Influence of Deposition Methods of Support Layer on Cordierite Substrate on the Characteristics of a MnO2–NiO–Co3O4/Ce0.2Zr0.8O2/Cordierite Three Way Catalyst

Directory of Open Access Journals (Sweden)

Phuong Thi Mai Pham

2014-09-01

Full Text Available This paper compares different coating methods (in situ solid combustion, hybrid deposition, secondary growth on seed, suspension, double deposition of wet impregnation and suspension to deposit Ce0.2Zr0.8O2 mixed oxides on cordierite substrates, for use as a three way catalyst. Among them, the double deposition was proven to be the most efficient one. The coated sample shows a BET (Brunauer–Emmett–Teller surface area of 25 m2/g, combined with a dense and crack free surface. The catalyst with a layer of MnO2–NiO–Co3O4 mixed oxides on top of the Ce0.2Zr0.8O2/cordierite substrate prepared by this method exhibits good activity for the treatment of CO, NO and C3H6 in exhaust gases (CO conversion of 100% at 250 °C, C3H6 conversion of 100% at 400 °C and NO conversion of 40% at 400 °C.

Large magnetoresistance in Heusler-alloy-based epitaxial magnetic junctions with semiconducting Cu(In{sub 0.8}Ga{sub 0.2})Se{sub 2} spacer

Energy Technology Data Exchange (ETDEWEB)

Kasai, S. [Research Center for Magnetic and Spintronic Materials, National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Center for Emergent Matter Science, RIKEN, 2-1 Hirosawa, Wako 351-0198 (Japan); Takahashi, Y. K.; Ohkubo, T. [Research Center for Magnetic and Spintronic Materials, National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Cheng, P.-H.; Ikhtiar,; Mitani, S.; Hono, K. [Research Center for Magnetic and Spintronic Materials, National Institute for Materials Science (NIMS), 1-2-1 Sengen, Tsukuba 305-0047 (Japan); Graduate School of Pure and Applied Sciences, University of Tsukuba, 1-1-1 Tennodai, Tsukuba 305-8577 (Japan); Kondou, K. [Center for Emergent Matter Science, RIKEN, 2-1 Hirosawa, Wako 351-0198 (Japan); Otani, Y. [Center for Emergent Matter Science, RIKEN, 2-1 Hirosawa, Wako 351-0198 (Japan); Institute for Solid State Physics, University of Tokyo, 5-1-5 Kashiwanoha, Kashiwa 277-8581 (Japan)

2016-07-18

We investigated the structure and magneto-transport properties of magnetic junctions using a Co{sub 2}Fe(Ga{sub 0.5}Ge{sub 0.5}) Heusler alloy as ferromagnetic electrodes and a Cu(In{sub 0.8}Ga{sub 0.2})Se{sub 2} (CIGS) semiconductor as spacers. Owing to the semiconducting nature of the CIGS spacer, large magnetoresistance (MR) ratios of 40% at room temperature and 100% at 8 K were obtained for low resistance-area product (RA) values between 0.3 and 3 Ω μm{sup 2}. Transmission electron microscopy observations confirmed the fully epitaxial growth of the chalcopyrite CIGS layer, and the temperature dependence of RA indicated that the large MR was due to spin dependent tunneling.

Exon: CBRC-DMEL-08-0024 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DMEL-08-0024 atgtcatacttcactgagctcgtaataaaatttccaatcaaactgtgttcaaaaatggaaattaaattttttggccatattttccaaa...ttttgatgacccccatccttacaaaaaatgcgaaaattgatccaaaaattaatttcctaaatccttcaaaaagtaatagggatc ...

Structural and magnetic properties of Ni0.8M0.2Fe2O4 (M = Cu, Co) nano-crystalline ferrites

Science.gov (United States)

Vijaya Babu, K.; Satyanarayana, G.; Sailaja, B.; Santosh Kumar, G. V.; Jalaiah, K.; Ravi, M.

2018-06-01

Nano-crystalline nickel ferrites are interesting materials due to their large physical and magnetic properties. In the present work, two kinds of spinel ferrites Ni0.8M0.2Fe2O4 (M = Cu, Co) are synthesized by using sol-gel auto-combustion method and the results are compared with NiFe2O4. The structural properties of synthesized ferrites are determined by using X-ray powder diffraction; scanning electron microscope and Fourier transform infrared spectroscopy. The cation distribution obtained from X-ray diffraction show that cobalt/copper occupies only tetrahedral site in spinel lattice. The lattice constant increases with the substitution of cobalt/copper. The structural parameters like bond lengths, tetrahedral and octahedral edges have been varied with the substitution. The microstructural study is carried out by using SEM technique and the average grain size is increased with nickel ferrite. The initial permeability (μi) is improving with the substitution. The observed g-value from ESR is approximately equal to standard value.

The dynamics of the quasielastic 16O(e,e'p) reaction at Q2 = 0.8 (GeV/c)2

International Nuclear Information System (INIS)

Fissum, Kevin

2004-01-01

The physics program in Hall A at Jefferson Lab commenced in the summer of 1997 with a detailed investigation of the 16O(e,e'p) reaction in quasielastic, constant (q,w) kinematics at Q 2 ∼ 0.8 (GeV/c) 2 , q ∼ 1 GeV/c, and w ∼ 445 MeV. Use of a self-calibrating, self-normalizing, thin-film waterfall target enabled a systematically rigorous measurement. Differential cross-section data for proton knockout were obtained for 0 < Emiss < 120 MeV and 0 < pmiss < 350 MeV/c. These results have been used to extract the ALT asymmetry and the RL, RT, RLT, and RL+TT effective response functions. Detailed comparisons of the data with Relativistic Distorted-Wave Impulse Approximation, Relativistic Optical-Model Eikonal Approximation, and Relativistic Multiple-Scattering Glauber Approximation calculations are made. The kinematic consistency of the 1p-shell normalization factors extracted from these data with respect to all available 16O(e,e'p) data is examined. The Q2-dependence of the normalization factors is also discussed

Magnetic characterization of Nd0.8Sr0.2(Mn1-x Co x )O3 perovskites

International Nuclear Information System (INIS)

Vidal, Karmele; Lezama, Luis; Arriortua, Maria I.; Rojo, Teofilo; Gutierrez, Jon; Barandiaran, Jose M.

2005-01-01

We present a magnetic study of the family of perovskites Nd 0.8 Sr 0.2 (Mn 1- x Co x )O 3 (x=0.1, 0.2 and 0.3). These compositions have been prepared by using both the sol-gel method and the freeze-drying technique. As a result, we have obtained polycrystalline powder-like samples. We have obtained pure compounds that have been indexed in the Pnma space group. The study of their magnetic properties shows a decrease of the measured low-temperature magnetic moment as the content of Co increases in the composition. However, a similar magnetic ordering temperature of about 130 K has been determined for all samples. All the studied compounds show insulating behaviour of the electrical resistivity

Exon: CBRC-RNOR-08-0271 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RNOR-08-0271 TCAAGAACTCTTCCAGGAACCAGGGAGTGGAAACAAATAGATAtcgtcgtcgtcgtcgtcgtcgt...cgccgccatcatcatcatcatcatcatcaccaccaccaccaccaccaccaccaccaccaccacACCCTTGTTTTCAAATAAGAGTCACTCTGGTATTTATATTCTGTA

Photoemission study of absorption mechanisms in Bi2.0Sr1.8Ca0.8La0.3Cu2.1O8+δ, BaBiO3, and Nd1.85Ce0.15CuO4

International Nuclear Information System (INIS)

Lindberg, P.A.P.; Shen, Z.; Wells, B.O.; Dessau, D.S.; Ellis, W.P.; Borg, A.; Kang, J.; Mitzi, D.B.; Lindau, I.

1989-01-01

Photoemission measurements in the constant-final-state (absorption) mode were performed on three different classes of high-temperature superconductors Bi 2.0 Sr 1.8 Ca 0.8 La 0.3 Cu 2.1 O 8+δ , BaBiO 3 , and Nd 1.85 Ce 0.15 CuO 4 using synchrotron radiation from 20 to 200 eV. Absorption signals from all elements but Ce are identified. The results firmly show that the Bi 6s electrons are more delocalized in BaBiO 3 than in Bi 2.0 Sr 1.8 Ca 0.8 La 0.3 Cu 2.1 O 8+δ , in agreement with the results of band-structure calculations. Differences in the absorption signals due to O and Bi excitations between BaBiO 3 and Bi 2.0 Sr 1.8 Ca 0.8 La 0.3 Cu 2.1 O 8+δ are discussed. Delayed absorption onsets attributed to giant resonances (Ba 4d→4f, La 4d→4f, and Nd 4d→4f transitions) are also reported

Defense waste salt disposal at the Savannah River Plant

International Nuclear Information System (INIS)

Langton, C.A.; Dukes, M.D.

1984-01-01

A cement-based waste form, saltstone, has been designed for disposal of Savannah River Plant low-level radioactive salt waste. The disposal process includes emplacing the saltstone in engineered trenches above the water table but below grade at SRP. Design of the waste form and disposal system limits the concentration of salts and radionuclides in the groundwater so that EPA drinking water standards will not be exceeded at the perimeter of the disposal site. 10 references, 4 figures, 3 tables

The leaching of lead from lead-based paint in landfill environments.

Science.gov (United States)

Wadanambi, Lakmini; Dubey, Brajesh; Townsend, Timothy

2008-08-30

Lead leaching from lead-based paint (LBP) was examined using standardized laboratory protocols and tests with leachate from actual and simulated landfill environments. Two different LBP samples were tested; leaching solutions included leachates from three municipal solid waste (MSW) landfills and three construction and demolition (C&D) debris landfills. The toxicity characteristic leaching procedure (TCLP) and the synthetic precipitation leaching procedure (SPLP) were also performed. Lead concentrations were many times higher using the TCLP compared to the SPLP and the landfill leachates. No significant difference (alpha=0.05) was observed in leached lead concentrations from the MSW landfill and C&D debris landfill leachates. The impact of other building materials present in LBP debris on lead leaching was examined by testing mixtures of LBP (2%) and different building materials (98%; steel, wood, drywall, concrete). The type of substrate present impacted lead leaching results, with concrete demonstrating the most dramatic impact; the lowest lead concentrations were measured in the presence of concrete under both TCLP and SPLP extractions.

Exon: CBRC-RNOR-08-0339 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RNOR-08-0339 ctcccagaaaaaaaaaagaaaaggaaAGGAAAagaaaaggaagggaggggagaaggaaggaaacagaagagaagggggggtgagaag...aggagaggggaagaagaagaggagggagaggagatgggatggggagagaggaaaggggaggggacggggaggagggaagaAAGGAACAAGGGAGACTAAAAGAGAAGGAAG ...

Interrelation of transport properties, defect structure and spin state of Ni3+ in La1.2Sr0.8Ni0.9Fe0.1O4+δ

Science.gov (United States)

Gilev, A. R.; Kiselev, E. A.; Zakharov, D. M.; Cherepanov, V. A.

2017-10-01

The total conductivity, Seebeck coefficient and oxygen non-stoichiometry for La1.2Sr0.8Ni0.9Fe0.1O4+δ have been measured vs temperature and oxygen partial pressure P(O2). The measurements were carried out at 800, 850, 900 and 950 °C within the P(O2) range of 10-5-0.21 atm. La1.2Sr0.8Ni0.9Fe0.1O4+δ was shown to be oxygen deficient in all temperature and P(O2) ranges studied. The calculated values of the partial molar enthalpy of oxygen depend very slightly on oxygen content (δ), indicating that La1.2Sr0.8Ni0.9Fe0.1O4+δ with the oxygen deficiency can be considered an ideal solution. The model of point defect equilibria in La1.2Sr0.8Ni0.9Fe0.1O4+δ has been proposed and fitted to experimental dependencies. Subsequent joint analysis of the defect structure and transport properties revealed that electron holes can coexist in both localized and quasi-delocalized states in the oxide: the former corresponded to high-spin state Ni3+ and the latter - to low-spin state Ni3+. The mobilities of localized electron holes were shown to be significantly lower in comparison to quasi-delocalized ones. The behavior of localized electron holes was explained in terms of a small polaron conduction mechanism; in contrast, quasi-delocalized electron holes were described in terms of a band conduction approach. The small polaron conduction mechanism was shown to be predominant in the Sr- and Fe-co-doped lanthanum nickelate.

Tööaja arvestamine ja lisatasude maksmine tükitöö puhul. Riigikohtu tsiviilkolleegiumi otsus asjas 3-2-1-6-08 / Merle Muda

Index Scriptorium Estoniae

Muda, Merle, 1972-

2009-01-01

Riigikohtu otsusest 3-2-1-6-08: OÜ Arliten (endine OÜ Anubis Expert) kassatsioonkaebus Tartu Ringkonnakohtu 03.10.2007. a otsusele Oliver Surva hagis OÜ Arliten (endine OÜ Anubis Expert) vastu töövaidluses

Exon: CBRC-RNOR-08-0336 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RNOR-08-0336 gaagcgcaaggccctgggttcggtccccagctccgaaaaaaagaaccaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaaagaaa...aaaaaaaaagaaaaaaaaaaaagaaaagaaaagaaaagaaggcaggctgagcaagggtagggaacaagccagtaagcggtgtt...cttcaacaatctcagctttcgtccctgtcctgacaactctcagtgaagaatatgtaagccaaacaaaccctcccctccacacgttggttttggtctgttttaacacagcagtagaaagcaaactagACGACCTTACTGTAAAATCAg ...

Exon: CBRC-MMUS-08-0013 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MMUS-08-0013 aaagaaagaaagaaagaaagaaaaaaagaaagaaagaaagaaagaaagaaggaaggaaggaagga...aggaaggaaggaaggaaggaaggaaggaaggaagggaaggaaggaaggaaggaaggaaggaaggaaggaaggaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaa...gaaagaaagGGCCAGGGATGTGTTTGGtgtttggtggaggcatggtatggtgtgggggaagagggtgcctctgcgggaccatgctga ...

Interaction of hydrogen sulfide with Zr0.92Y0.08O2-δ/40% Ni cermet

International Nuclear Information System (INIS)

Siriwardane, R.V.; Poston, J.A. Jr.; Fisher, E.P.

2005-01-01

The interaction of hydrogen sulfide with a cermet composed of zirconium oxide and yttrium oxide doped with metallic nickel (Ni) in the stoichiometric form Zr 0.92 Y 0.08 O 2-δ /40 vol% Ni and a pure nickel metal was studied at 500 and 650 deg. C utilizing high temperature X-ray photoelectron spectroscopy and high-temperature scanning electron microscopy. The hydrogen sulfide (H 2 S) did not appear to interact with the cermet at 500 deg. C with H 2 S exposures of 6 x 10 -5 Torr for 1 h, but interaction of H 2 S with the cermet was observed at 650 deg. C at similar H 2 S exposures. The amount and the rate of reaction of H 2 S were significantly lower with the cermet than with the pure nickel metal at 650 deg. C with similar H 2 S exposures. The dispersion of nickel in the zirconium and yttrium oxide matrix decreased the reaction of H 2 S with nickel in the cermet

Mn0.8Zn0.2Fe2O4 nanoparticulates spinel ferrites: An approach to enhance the antenna field strength for improved magnitude versus offset (MVO

Directory of Open Access Journals (Sweden)

Majid Niaz Akhtar

2014-08-01

Full Text Available Electromagnetic signals in deep reservoir are very weak so that it is difficult to predict about the presence of hydrocarbon in seabed logging (SBL environment. In the present work, Mn0.8Zn0.2Fe2O4 nanoferrites were prepared by a sol–gel technique at different sintering temperatures of 450 °C, 650 °C and 850 °C to increase the strength of electromagnetic (EM antenna. XRD, FESEM, Raman spectroscopy and HRTEM were used to analyze the phase, surface morphology and size of the nanoferrites. Magnetic properties of the nanoferrites were also measured using an impedance network analyzer. However, nanoferrites sintered at 850 °C with initial permeability of 200 and Q factor of 50 were used as magnetic feeders with the EM antenna. Lab scale experiments were performed to investigate the effect of magnetic field strength in scale tank. SPSS and MATLAB softwares were also used to confirm the oil presence in scale tank. It was observed that the magnitude of the EM waves for the antenna was increased up to 233%. Finally, the correlation values also show 208% increase in the magnetic field strength with the presence of the oil. Therefore, antenna with Mn0.8Zn0.2Fe2O4 nanoferrites based magnetic feeders can be used for deep water and deep target hydrocarbon exploration.

Synthesis and characterization of La0.8Sr0.2Ni(1−xCrxO3 (x = 0.0, 0.2, 0.4, 0.6, 0.8, 1.0 system by the combustion method

Directory of Open Access Journals (Sweden)

Jairo Alberto Gómez-Cuaspud

2017-11-01

Full Text Available This research focuses on the synthesis and characterization of six ceramic perovskite oxides based on La0.8Sr0.2Ni(1−xCrxO3 system, with different levels of chromium modification (x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0, for use as anode material in solid oxide fuel cells (SOFC. The oxides were obtained in two reaction stages, starting from corresponding nitrate salts and citric acid until formation of a solid metal complex consistent with citrate species. The solid metalorganic foams were calcined at 1000 °C for 120 min under oxygen flow conditions and were characterized by infrared and ultraviolet spectroscopy (FTIR-UV, validating the proposed methodology in terms of purity and chemical composition. The characterization by X-ray diffraction (XRD, scanning electron microscopy (SEM and X-ray energy dispersive spectroscopy (EDX confirms the obtention of a homogeneous perovskite structure in all analyzed phases. The evaluation of crystallite size by means of the Debye–Scherrer equation establishes a nanometric prevalence around 3.2–4.4 nm along main diffraction signals. The electrical characterization of materials by solid-state impedance spectroscopy allowed identifying a particular behavior depending on the microstructure of solids for potential applications in SOFC devices. Resumen: Esta investigación se centra en la síntesis y caracterización de seis óxidos de perovskita cerámicos basados en el sistema La0.8Sr0.2Ni(1-xCrxO3, con diferentes niveles de modificación de cromo (x = 0.0, 0.2, 0.4, 0.6, 0.8 y 1.0, para uso como material de ánodo en pilas de combustible de óxido sólido (SOFC. Los óxidos se obtuvieron en dos etapas de reacción, partiendo de las correspondientes sales de nitrato y ácido cítrico hasta la formación de un complejo metálico sólido consistente con especies de citrato. Las espumas sólidas metal-orgánicas se calcinaron a 1000° C

Exon: CBRC-RNOR-08-0339 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RNOR-08-0339 gacagccagggttacaaagagaaatcatcttggaaaaaaaaaGGAAGaggaacgaaggaaggaaggaagcgaaggaaggaaa...gaaggaaggatagaagggaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaaggaaggaaggaaggaaggaaggaaggaaggaaggagagagaaa...gggaaggaaggaagCGAtgtgtttataaaaaaaataaagagagggaggatatgttttgtggag ...

Exon: CBRC-CBRI-08-0163 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-CBRI-08-0163 aatacggtaaaaaattggagacctctaaaattcagaaattcagaaattcagaaattcagaaaatccggaaattcggaatttcagaaaa...tcagaaattcagaaactcagaaattcggaatttcagaaattcagaaattcagaaattcggaatttcgaaattcagaaactcagaaactcggaaattcagaaattcagaaa...ttcagaaattcagaaattcagaaattcagaaattcagaaattcagaaaatccggaaattcggaatttcagaaaatcagaaattcagaaattcagaaattcagaaa...ttcagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaa...ttcaaggattcagaaattcagaaattcagaaattcggaatttgagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaattcagaaatccagaaa

Exon: CBRC-MMUS-08-0013 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MMUS-08-0013 agaaacccccgtctcaaaaaacaaaaCAAACAAACAAAAAATCAAAACAaaagaaagagagaaagagagaaa...gagagaggggggggagagagagagaaagagagaaagagaaagagagaaagaaagaaagagagagagagagagagagagaaagaaagaaagaaagaaaggaa...ggaaggaaggaaggaaggaaggaaggaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaagaaaagtagaggacaagtataaa...gaattatatctgggctgtggtgaaaggatgagggccccttgcagtcagagctccttcacggcatccccaaagtctttttatgaatgtatcaggaa ...

Exon: CBRC-MMUS-08-0051 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MMUS-08-0051 ATGcacacacacatgtgcacacatgcatacacacatgcacacacattctcacacacacatatacacacatgcacacatgatgcacacaca...cgcacacacatgaatgcacatgcacaaacacatataagcacacacagatgcatgcacatgcactcacacataaacccacacacatgtgcacacatgcatgcaca...cttgcatgcacacacatacacacatacacacactcacacacatctacatatatacactctcacacatgcacatatacacacatgcatacatccttgcacccgcacaca...tacacatactcacacacatacacacatacacacacccacacatatagacacacgcatacacgatgcacacacacatacacaca...cccacacatatagtcacacgaatacacgatgcatacacacacatatacacacatgcacacacgatgcacacacacatacacatccacacatagatgcacatgcatacaca

Exon: CBRC-HSAP-08-0044 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-HSAP-08-0044 atgagcatcggcatcgccattatcataatcattactatcattattattgatagtgatatcaccatcaccaccatcacca...tcatcgtcatcaccatgaccatcattatcttcaccatcatcactatcaccatcatcatcatcaccatcaccaccatcaccattatcatcaccattgccatcatcaccatcacca...tcattatcttcatcatcactatcaccatcatcatcaccaccatcaccatcatcatcaccatcaccatcatcatcaccaccatcatcatcacca...tGATGGATAATAATATAATCATTGTCTtcaccatcacaaccatcatcatcatcaccaccaccatcattaacactatgatggataatatcatcttcacca...tcataaccatcaccattactatcatcaccatcaccatcaacaccaccaccactatcatcatgattgccatcatcaccatcatcat

Exon: CBRC-MMUS-08-0013 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-MMUS-08-0013 CCCAGAGTTCAGTTCTCAGCcacacacacacacacacacacacacacacacacacacacacacacacacatacacacacacacacacaca...cacagagagagagagagagagagagagagagagagagagagagagagagagagagagaaacagagaggcagagacagagagag...aCACACAGATATACAAACAGAAACTCAAATAGACACAGAGAGacacacatacagacacatacacacacccacacatacacacgcaTGCATAGAGAGAAAGAAACACCgacaaacagacacagacagagacaca...aacactgatacatacagacagacatactcacacagaggaacagacatatacacagactcacaaacaaccag ...

Engineering Mixed Ionic Electronic Conduction in La 0.8 Sr 0.2 MnO 3+ δ Nanostructures through Fast Grain Boundary Oxygen Diffusivity

KAUST Repository

Saranya, Aruppukottai M.; Pla, Dolors; Morata, Alex; Cavallaro, Andrea; Canales-Vá zquez, Jesú s; Kilner, John A.; Burriel, Mó nica; Tarancó n, Albert

2015-01-01

to implement in nanostructures. Here, an artificial mixed ionic electronic conducting oxide is fabricated by grain boundary (GB) engineering thin films of La0.8Sr0.2MnO3+δ. This electronic conductor is converted into a good mixed ionic electronic conductor

Superconducting single X-ray photon detector based on W0.8Si0.2

Directory of Open Access Journals (Sweden)

Xiaofu Zhang

2016-11-01

Full Text Available We fabricated a superconducting single X-ray photon detector based on W0.8Si0.2, and we characterized its basic detection performance for keV-photons at different temperatures. The detector has a critical temperature of 4.97 K, and it is able to be operated up to 4.8 K, just below the critical temperature. The detector starts to react to X-ray photons at relatively low bias currents, less than 1% of Ic at T = 1.8 K, and it shows a saturated count rate dependence on bias current at all temperatures, indicating that the optimum internal quantum efficiency can always be reached. Dark counts are negligible up to the highest investigated bias currents (99% of Ic and operating temperature (4.8 K. The latching effect affects the detector performance at all temperatures due to the fast recovery of the bias current; however, further modifications of the device geometry are expected to reduce the tendency for latching.

Exon: CBRC-RNOR-08-0342 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-RNOR-08-0342 acacacagacacacacagacacatagacacacacagagacacactcacaaacacacacagacacacacacagacacacacagacacaca...tatatagacacacagacacacacagacacatacacacaaacacacacagacacatacacacagacacagacacagacacacacagacacacagacacacacacacaca...gacacacacagacacacacagacacacagacaatacacagacacacagacacacacatagacacacaaatacacacaaacacacacacaacacacacagacacacaca...aacacacacacagacatacacacagacacacagacacacacagacacacagacacagacacagacacacagacacagacaca...cagacacacagacacacagacacacacagacacacacacacaacacacagacaaacacacagacacacacacagacacagacacacacacacagacacNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN ...

Solvothermal coating LiNi_0_._8Co_0_._1_5Al_0_._0_5O_2 microspheres with nanoscale Li_2TiO_3 shell for long lifespan Li-ion battery cathode materials

International Nuclear Information System (INIS)

Wu, Naiteng; Wu, Hao; Liu, Heng; Zhang, Yun

2016-01-01

LiNi_0_._8Co_0_._1_5Al_0_._0_5O_2 (NCA) microspheres covered by a nanoscale Li_2TiO_3-based shell were synthesized by a facile strategy based on a solvothermal pre-coating treatment combined with a post-sintering lithiation process. The morphology, structure and composition of the Li_2TiO_3-coated NCA samples were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning scanning electron microscope (SEM) with an energy-dispersive X-ray spectroscope (EDS), and transmission electron microscopy (TEM). Owing to the complete, uniform and nanoscale Li_2TiO_3 coating shell, the resultant surface-modified NCA microspheres used as Li-ion battery cathode materials manifest remarkably enhanced cycling performances, attaining 94% and 84% capacity retention after 200 and 400 cycles at 0.5 C, respectively, which is much better than the pristine NCA counterpart (60% retention, 200 cycles). More impressively, the surface-modified NCA also shows an intriguing storage stability. After being stored at 30 °C for 50 days, the coated NCA-based cells are subjected to be cycled both at room and elevated temperatures, in which the aged cells can still remain 84% capacity retention after 200 cycles at 25 °C and 77% capacity retention after 200 cycles at 55 °C, respectively. All these results demonstrate that the Li_2TiO_3-coated LiNi_0_._8Co_0_._1_5Al_0_._0_5O_2 microsphere is a promising cathode material for Li-ion batteries with long lifespan. - Graphical abstract: Nanoscale Li_2TiO_3-based shell encapsulated LiNi_0_._8Co_0_._1_5Al_0_._0_5O_2 (NCA) microspheres are fabricated through a solvothermal pre-coating treatment combined with post-lithiation process. The surface-coated NCA as cathode materials shows a remarkably enhanced cycling performance and storage stability for long lifespan Li-ion batteries. - Highlights: • Li_2TiO_3 is used as coating materials for layer structured LiNi_0_._8Co_0_._1_5Al_0_._0_5O_2 cathode. • Solvothermal coating

ISS Expedition 08 Press Kit

Data.gov (United States)

National Aeronautics and Space Administration — Press kit for ISS mission Expedition 08 from 10/2003-04/2004. Press kits contain information about each mission overview, crew, mission timeline, benefits, and media...

Comparison in the electronic structure of YBa{sub 2}Fe{sub 3}O{sub 8} insulator with YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} superconductors

Energy Technology Data Exchange (ETDEWEB)

Zhang, Y.; Guan, X.Y. [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); Cheng, C.H. [School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia); Pan, M. [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); Zhang, H. [Department of Physics, Peking University, Beijing 100871 (China); Zhao, Y., E-mail: yzhao@home.swjtu.edu.cn [Key Laboratory of Magnetic Suspension Technology and Maglev Vehicle, Ministry of Education, Superconductivity R and D Center, Southwest Jiaotong University, Chengdu 610031 (China); School of Materials Science and Engineering, University of New South Wales, Sydney, 2052 NSW (Australia)

2013-10-15

Highlights: • The electronic structure of YBa{sub 2}Fe{sub 3}O{sub 8}, YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} were investigated by XPS. • The core-level and valence-band structures of these systems are different. • The density of states at Fermi level is related to the superconductivity. -- Abstract: The electronic structure and chemical states of relevant elements of YBa{sub 2}Fe{sub 3}O{sub 8} are investigated using X-ray photoemission spectroscopy (XPS), compared with those of YBa{sub 2}Cu{sub 3}O{sub 7} and SmFeAsO{sub 0.8}F{sub 0.2} superconductors. The typical differences and similarities in core-level and valence-band structures of these systems have been detected, strongly suggesting that the superconductivity have the finite density of states around Fermi level. Several features of O1s, Y3d, Ba3d, and Fe2p core lines in XPS spectra are also carefully compared and analyzed.

Structure refinement of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-d} as cathode materials for intermediate temperature solid oxide fuel cells (IT-SOFC)

Energy Technology Data Exchange (ETDEWEB)

Zakaria, Nurhamidah, E-mail: nurhamidahzakaria@yahoo.com; Idris, Mohd Sobri, E-mail: sobri@unimap.edu.my [Centre of Excellence for Frontier Materials Research, School of Materials Engineering, Universiti Malaysia Perlis (UniMAP), Taman Muhibbah, Jejawi 02600, Arau, Perlis (Malaysia); Osman, Rozana A. M., E-mail: rozana@unimap.edu.my [School of Microelectronics Engineering, Universiti Malaysia Perlis (UniMAP), Pauh Putra, 02600, Arau, Perlis (Malaysia)

2016-07-19

Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} was successfully prepared using modified solid-state synthesis routes. The lowest temperature to obtained single phase of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} is about 900°C for 15 hours. Longer period of time are required compared to only 5 hours at 950°C as established in literatures. The X-ray Diffraction (XRD) data confirmed that Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} is formed a cubic perovskite with the space group of Pm-3m. The lattice parameters of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} are a = 3.990 (1) Å and unit cell volume is V = 63.5 (1) Å{sup 3}. The Rietveld refinement of XRD data revealed that the crystal structure of Ba{sub 0.5}Sr{sub 0.5}Co{sub 0.8}Fe{sub 0.2}O{sub 3-δ} slightly changes as a function of temperature.

Phase stability and oxygen non-stoichiometry of SrCo0.8Fe0.2O3-d measured by in-situ neutron diffraction

NARCIS (Netherlands)

McIntosh, Steven; McIntosh, S.; Vente, Jaap F.; Haije, Wim G.; Blank, David H.A.; Bouwmeester, Henricus J.M.

2006-01-01

The phase stability, oxygen stoichiometry and expansion properties of SrCo0.8Fe0.2O3−δ (SCF) were determined by in situ neutron diffraction between 873 and 1173 K and oxygen partial pressures of 5×10−4 to 1 atm. At a pO2 of 1 atm, SCF adopts a cubic perovskite structure, space group Pm3¯m, across

Ambipolar gate effect and low temperature magnetoresistance of ultrathin La0.8Ca0.2MnO3 films.

Science.gov (United States)

Eblen-Zayas, M; Bhattacharya, A; Staley, N E; Kobrinskii, A L; Goldman, A M

2005-01-28

Ultrathin La(0.8)Ca(0.2)MnO(3) films have been measured in a field-effect geometry. The gate electric field produces a significant ambipolar decrease in resistance at low temperatures. This is attributed to the development of a pseudogap in the density of states and the coupling of localized charge to strain. Within a mixed phase scenario, the gate effect and magnetoresistance are interpreted in the framework of a "general susceptibility," which describes how phase boundaries move through a hierarchical pinning landscape.

The influence of AlCrN coating on the high-temperature corrosion resistance of Ti-46Al-7Nb alloy in an atmosphere containing 9% O{sub 2} + 0.2% HCl + 0.08% SO{sub 2} + N{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Malecka, Joanna [Opole Univ. of Technology (Poland). Faculty of Mechanical Engineering

2013-09-15

The results of investigation of the isothermal oxidation wear mechanism of Ti-46Al-7Nb-0.7Cr-0.1Si-0.2Ni intermetallic alloy with AlCrN coating are presented. Tests in 9% O{sub 2} + 0.2% HCl + 0.08% SO{sub 2} + N{sub 2} atmosphere were performed at a temperature of 700 C. The structure of the specimen and chemical composition of the oxidation products were analysed using scanning electron microscopy and energy dispersive X-ray analysis. In addition, mass changes were investigated.

Stabilization/solidification of selenium-impacted soils using Portland cement and cement kiln dust.

Science.gov (United States)

Moon, Deok Hyun; Grubb, Dennis G; Reilly, Trevor L

2009-09-15

Stabilization/solidification (S/S) processes were utilized to immobilize selenium (Se) as selenite (SeO(3)(2-)) and selenate (SeO(4)(2-)). Artificially contaminated soils were prepared by individually spiking kaolinite, montmorillonite and dredged material (DM; an organic silt) with 1000 mg/kg of each selenium compound. After mellowing for 7 days, the Se-impacted soils were each stabilized with 5, 10 and 15% Type I/II Portland cement (P) and cement kiln dust (C) and then were cured for 7 and 28 days. The toxicity characteristic leaching procedure (TCLP) was used to evaluate the effectiveness of the S/S treatments. At 28 days curing, P doses of 10 and 15% produced five out of six TCLP-Se(IV) concentrations below 10mg/L, whereas only the 15% C in DM had a TCLP-Se(IV) concentration soil-cement slurries aged for 30 days enabled the identification of Se precipitates by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM)-energy dispersive X-ray spectroscopy (EDX). XRD and SEM-EDX analyses of the Se(IV)- and Se(VI)-soil-cement slurries revealed that the key selenium bearing phases for all three soil-cement slurries were calcium selenite hydrate (CaSeO(3).H(2)O) and selenate substituted ettringite (Ca(6)Al(2)(SeO(4))(3)(OH)(12).26H(2)O), respectively.

Comparison of structural and electric properties of PbZr0.2Ti0.8O3 and CoFe2O4/PbZr0.2Ti0.8O3 films on (100)LaAlO3

Science.gov (United States)

Zhang, X. D.; Dho, Joonghoe; Park, Sungmin; Kwon, Hyosang; Hwang, Jihwan; Park, Gwangseo; Kwon, Daeyoung; Kim, Bongju; Jin, Yeryeong; Kim, Bog. G.; Karpinsky, D.; Kholkin, A. L.

2011-09-01

In this work, we investigated structural, electrical, and magnetic properties of ferroelectric PbZr0.2Ti0.8O3 (PZT) and ferrimagnetic/ferroelectric [CoFe2O4(CFO)/PZT] bilayers grown on (100)LaAlO3 (LAO) substrates supplied with bottom 50 nm thick LaNiO3 electrodes. Interestingly, structural and electrical properties of the PZT layer exhibited remarkable changes after the top-layer CFO deposition. X-ray diffraction data suggested that both the c- and a-domains exist in the PZT layer and the tetragonality of the PZT decreases upon the top-layer deposition. A variation in the electrical properties of the PZT layer upon the CFO deposition was investigated by polarization versus voltage (P-V), capacitance versus voltage (C-V), and capacitance versus frequency (C-f) measurements. The CFO deposition induced a slight decrease of the remnant polarization and more symmetric behavior of P-V loops as well as led to the improvement of fatigue behavior. The tentative origin of enhanced fatigue endurance is discussed based on the measurement results. These results were corroborated by local piezoelectric measurements. Ferrimagnetic property of the CFO/PZT bilayer was confirmed by magnetic measurement at room temperature.

40 CFR 600.109-08 - EPA driving cycles.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false EPA driving cycles. 600.109-08 Section... Model Year Automobiles-Test Procedures § 600.109-08 EPA driving cycles. (a) The FTP driving cycle is prescribed in § 86.115 of this chapter. (b) The highway fuel economy driving cycle is specified in this...

Deep levels in as-grown and Si-implanted In(0.2)Ga(0.8)As-GaAs strained-layer superlattice optical guiding structures

Science.gov (United States)

Dhar, S.; Das, U.; Bhattacharya, P. K.

1986-01-01

Trap levels in about 2-micron In(0.2)Ga(0.8)As(94 A)/GaAs(25 A) strained-layer superlattices, suitable for optical waveguides, have been identified and characterized by deep-level transient spectroscopy and optical deep-level transient spectroscopy measurements. Several dominant electron and hole traps with concentrations of approximately 10 to the 14th/cu cm, and thermal ionization energies Delta-E(T) varying from 0.20 to 0.75 eV have been detected. Except for a 0.20-eV electron trap, which might be present in the In(0.2)Ga(0.8)As well regions, all the other traps have characteristics similar to those identified in molecular-beam epitaxial GaAs. Of these, a 0.42-eV hole trap is believed to originate from Cu impurities, and the others are probably related to native defects. Upon Si implantation and halogen lamp annealing, new deep centers are created. These are electron traps with Delta-E(T) = 0.81 eV and hole traps with Delta-E(T) = 0.46 eV. Traps occurring at room temperature may present limitations for optical devices.

Preparation of the La0.8Sr0.2MnO3 films on STO and LAO substrates by excimer laser-assisted metal organic deposition using the KrF laser

International Nuclear Information System (INIS)

Tsuchiya, T.; Daoudi, K.; Manabe, T.; Yamaguchi, I.; Kumagai, T.

2007-01-01

La 0.8 Sr 0.2 MnO 3 films were prepared on SrTiO 3 (STO) and LaAlO 3 (LAO) substrates using excimer laser-assisted metal organic deposition (ELAMOD). For the LAO substrate, no epitaxial La 0.8 Sr 0.2 MnO 3 film was obtained by laser irradiation in the fluence range from 60 to 110 mJ/cm 2 with heating at 500 deg. C. On the other hand, an epitaxial La 0.8 Sr 0.2 MnO 3 film on the STO substrate was formed by laser irradiation in the fluence range from 60 to 100 mJ/cm 2 with heating at 500 deg. C. To optimize the electrical properties for an IR sensor, the effects of the laser fluence, the irradiation time and the film thickness on the temperature dependence of the resistance and temperature coefficient of resistance (TCR: defined as 1/R.(dR/dT)) of the LSMO films were investigated. An LSMO film on the STO substrate that showed the maximum TCR of 3.9% at 265 K was obtained by the ELAMOD process using the KrF laser

Equilibrium leaching of toxic elements from cement stabilized soil.

Science.gov (United States)

Voglar, Grega E; Leštan, Domen

2013-02-15

The toxicity characteristics leaching procedure (TCLP) is commonly used to assess the efficiency of solidification/stabilization (S/S) of pollutants in wastes, despite recent objections to this method. In this study, formulations of 7, 10, 15 and 20% (w/w) of calcium aluminate cement (CAC) and sulfate resistant Portland cement (SRC) were used for S/S of soil from brownfield contaminated with 43,149, 10,115, 7631, 6130, 90, 82 mg kg(-1) of Zn, Pb, Cu, As, Cd and Ni, respectively. CAC produced S/S soil monoliths of higher mechanical strength (up to 7.65 N mm(-2)). Mass-transfer analysis indicated surface wash-off as a mechanism of toxic elements release, and equilibrium leaching as a crucial parameter of S/S efficiency assessment. In the expected range of field soil pH after S/S (pH 7-9), the TCLP gave markedly different results than the multi-point pH equilibrium leaching method (using nine targeted pH values): up to 2953-, 94-, 483-, 1.3-, 27- and 1.5-times more Zn, Pb, Cu, As, Cd and Ni, respectively, was determined in the TCLP leachate. S/S with CAC reduced leachability of toxic elements more effectively than SRC. Our results indicate that, under given field conditions, the TCLP significantly underrates the efficiency of S/S of contaminated soil with cementitious binders. Copyright © 2012 Elsevier B.V. All rights reserved.

Assessment of heavy metal mobility in mine tailings in the province of Huelva; Evaluacion de la movilidad de metales pesados en residuos mineros de flotacion de mineria metalica en la provincia de Huelva

Energy Technology Data Exchange (ETDEWEB)

Arranz Gonzalez, J. C.; Cala Rivero, V.

2011-07-01

Metallurgic mine wastes often contain high concentrations of potentially toxic elements, the mobility of which may pose an environmental hazard for water and surrounding ecosystems. We have examined the mobility of Ag, As, Cu, Pb and Zn from composite surface samples (0-20 cm) of different pyritic tailings impoundments in the province of Huelva (Spain). These samples were also subject to physical chemical and mineralogical (XRD) characterization. The total metal content of the tailings ranged between 1.89-11.2 ppm for Ag, 72-610 ppm for As, 245-1194 ppm for Cu, 220-11933 for Pb and 41-706 for Zn, all proving to be highly acidic. The mobility of these elements was assessed by using a seven-step sequential extraction procedure and applying the toxicity characteristic leaching procedure (TCLP). We investigated the applicability of TCLP to the tailings by comparing the results with those of the first steps of the sequential extraction procedure. It was found that the pH values remained buffered (close to 4.97) upon adding the TCLP extraction reagent and that the pH values differed significantly from those of the aqueous extracts. This could result in an underestimation of mobile forms compared with those dissolved in water. We may also conclude that due to the presence of specific minerals or to the preference of some elements for acetate ions the results of any assessment of metal mobility in pyritic tailings using the TCLP test may be questionable. (Author) 42 refs.

Anode-supported single-chamber solid oxide fuel cell based on cobalt-free composite cathode of Nd0.5Sr0.5Fe0.8Cu0.2O3-δ-Sm0.2Ce0.8O1.9 at intermediate temperatures

Science.gov (United States)

Yin, Jie-Wei; Zhang, Chunming; Yin, Yi-Mei; Shi, Huangang; Lin, Ye; Lu, Jun; Ma, Zi-Feng

2015-07-01

As a candidate of cathode material of single-chamber solid oxide fuel cell (SC-SOFC), cobalt-free mixed ionic electronic conductor (MIEC) Nd0.5Sr0.5Fe0.8Cu0.2O3-δ (NSFCu) is synthesized by sol-gel method with ethylene diamine tetraacetic acid and citric acid as co-complexing agents. The XRD shows NSFCu is stable after CO2 treatment and chemical compatible with SDC at high temperatures. CO2-TPD (CO2-temperature programmed desorption) demonstrates both CO2 adsorption and desorption phenomenon on NSFCu surface. However, the polarization resistances (Rp) of NSFCu and SDC (10:4 in weight) composite electrodes showed no decay in 5% CO2. Single cell using N2-O2-CH4 mixed gas (CH4 to O2 ratio = 1.5) as fuel shows maximum power density of 635 mW cm-2 at 700 °C. These results suggest that NSFCu-SDC is a promising composite cathode material for application in single-chamber solid oxide fuel cell.

Produksi Panel Dinding Bangunan Tahan Gempa dan Ramah Lingkungan dari Limbah Bahan Berbahaya dan Beracun Industri Minyak dan Gas

Directory of Open Access Journals (Sweden)

Luqman Hakim

2015-10-01

Full Text Available Berdasarkan hasil uji karakteristik fisik terhadap panel dinding dari komposit limbah industry migas berupa activated alumina, sandblasting dan glasswall yang telah dilakukan pada tahun pertama diketahui bahwa kuat lentur tertinggi diperoleh dari sampel B4 yaitu sebesar 67,8 Kg/Cm2 dengan standar DIN 1101 17 Kg/cm2, kuat desak sampel B 2 68,31 N/mm2 dengan standar bata merah 25 N/mm2 dan batako 20 N/mm2 dan tingkat keausan terendah diperoleh dari sampel 37 streap. Dari hasil tersebut diketahui bahwa uji telah memiliki kemampuan lebih tinggi jika dibandingkan dengan standar yang berlaku. Maka pada penelitian lanjutan yang akan dilakukan bertujuan untuk mempelajari apakah produk panel dinding ini ramah lingkungan sehingga aman bagi kesehatan manusia dan lingkungan sekitarnya.Penelitian dilakukan dengan menggunakan metode uji toxicity characteristic leaching procedure (TCLP dan LC50 terhadap produk panel dinding terbaik. Uji TCLP yang akan dilakukan yaitu dengan cara mendestruksi dan ekstraksi produk panel dinding dengan menggunakan rotating agitator selama 24 jam kemudian diuji dengan menggunakan AAS untuk mengetahui konsentrasi logam berat yang terdapat dalam produl panel dinding. Adapun untuk uji LC50 dilakukan dengan menggunakan hewan uji larva udang atau tikus.Berdasarkan hasil uji TCLP dan LC50 diketahui bahwa: a Kadar kandungan logam berat yang terdapat di dalam wall panel setelah dilakukan uji TCLP ternyata berada dibawah baku mutu seperti yang telah ditetapkan dalam PP No.85 Tahun 1999. Jadi ini artinya produk wall panel dalam penelitian ini ramah lingkungan, b pengujian terhadap bahan baku wall panel, Limbah Activated Alumina, Sandblasting dan Glasswoll sebelum di solidifikasi dapat mematikan sebesar 50% hewan uji pada konsentrasi 116.667 ppm dalam waktu 96 jam, dan c hasil uji LC50 terhadap produk wall panel selama 96 jam tidak menunjukkan adanya kematian hewan uji. Dari hasil penelitian ini dapat disimpulkan bahwa produk wall panel dari

Neutron production in bombardments of thin and thick W, Hg, Pb targets by 0.4, 0.8, 1.2, 1.8 and 2.5 GeV protons

International Nuclear Information System (INIS)

Letrourneau, A.; Galin, J.; Goldenbaum, F.; Lott, B.; Peghaire, A.; Enke, M.; Hilscher, D.; Jahnke, U.; Nuenighoff, K.; Filges, D.; Neef, R.D.; Paul, N.; Schaal, H.; Sterzenbach, G.; Tietze, A.

2000-05-01

Neutron experimental data relevant to the design of the target of neutron spallation sources are presented and discussed. The data include the reaction cross sections for W, Hg and Pb investigated with 0.4, 0.8, 1.2, 1.8 and 2.5 GeV proton beams as well as the neutron production, neutron multiplicity distribution, as determined event per event using a high efficiency detector. The production as a function of target material is investigated for both thin (with a single reaction) and thick targets (multiple reactions). Comparisons are made with the predictions of a high energy transport code. (authors)

Releasing metal catalysts via phase transition: (NiO)0.05-(SrTi0.8Nb0.2O3)0.95 as a redox stable anode material for solid oxide fuel cells.

Science.gov (United States)

Xiao, Guoliang; Wang, Siwei; Lin, Ye; Zhang, Yanxiang; An, Ke; Chen, Fanglin

2014-11-26

Donor-doped perovskite-type SrTiO3 experiences stoichiometric changes at high temperatures in different Po2 involving the formation of Sr or Ti-rich impurities. NiO is incorporated into the stoichiometric strontium titanate, SrTi0.8Nb0.2O3-δ (STN), to form an A-site deficient perovskite material, (NiO)0.05-(SrTi0.8Nb0.2O3)0.95 (Ni-STN), for balancing the phase transition. Metallic Ni nanoparticles can be released upon reduction instead of forming undesired secondary phases. This material design introduces a simple catalytic modification method with good compositional control of the ceramic backbones, by which transport property and durability of solid oxide fuel cell anodes are largely determined. Using Ni-STN as anodes for solid oxide fuel cells, enhanced catalytic activity and remarkable stability in redox cycling have been achieved. Electrolyte-supported cells with the cell configuration of Ni-STN-SDC anode, La0.8Sr0.2Ga0.87Mg0.13O3 (LSGM) electrolyte, and La0.6Sr0.4Co0.2Fe0.8O3 (LSCF) cathode produce peak power densities of 612, 794, and 922 mW cm(-2) at 800, 850, and 900 °C, respectively, using H2 as the fuel and air as the oxidant. Minor degradation in fuel cell performance resulted from redox cycling can be recovered upon operating the fuel cells in H2. Such property makes Ni-STN a promising regenerative anode candidate for solid oxide fuel cells.

Assessment of model chemistries for hydrofluoropolyethers: A DFT/M08-HX benchmark study

DEFF Research Database (Denmark)

da Franca E S C Viegas, Luis Pedro

2017-01-01

a good accuracy and considerable reduction in computational cost with respect to the benchmark, being more than three times faster than M08-HX/aug-pcseg-2//M08-HX/aug-pcseg-1. This cost-effective approach will be essential in future work when studying larger hydrofluoropolyethers, where the computational......n this work, we report the first detailed theoretical comparative conformational investigation between two different classes of hydrofluoropolyethers: dihydro- and dimethoxyfluoropolyethers. The main objective was to determine a cost-effective computational methodology that could accurately...

Magnetic properties and tunable magneto-caloric effect in La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 (x = 0.3, 0.5, and 0.7) compounds

Science.gov (United States)

Wu, Qiming; Wang, Xiangjie; Ding, Zan; Li, Lingwei

2018-05-01

The magnetic and magneto-caloric properties in the ternary elementals doped La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 (x = 0.3, 0.5, and 0.7) compounds were studied. With the increases of Co content x, the Curie temperature TC increases and the thermal hysteresis decreases. All the compounds undergo a second-order magnetic phase transition and exhibit a considerable reversible tunable magneto-caloric effect. The values of maximum magnetic entropy change (-ΔSMmax) and the Relative Cooling Power (RCP) are kept at same high level with different Co content. Under a magnetic field change of 0-5 T, the values of -ΔSMmax for La0.8Ce0.2Fe11.5-xCoxSi1.5C0.2 are 10.5, 10.7, and 9.8 J/kg K for x = 0.3, 0.5, and 0.7, respectively. The corresponding values of RCP are 267.1, 289.9, and 290.2 J/kg.

Transport characteristic in current-in-plane (CIP) geometry of La0.8Sr0.2MnO3/Co heterostructure

International Nuclear Information System (INIS)

Jin, K.X.; Zhao, S.G.; Chen, C.L.

2009-01-01

The thousand-fold change in the resistance with increase in temperature has been observed in the current-in-plane (CIP) geometry of the La 0.8 Sr 0.2 MnO 3 /Co heterostructure prepared using a sol-gel method. The CIP geometry below 300 K exhibits the variable-range hopping (VRH) mechanism. The current-voltage characteristic is nonlinear and the fitting shows that the exponent n decreases with increasing the temperature, which is attributed to the lattice mismatch between the LSMO film and the Co substrate.

A study on sintering aids for Sm{sub 0.2}Ce{sub 0.8}O{sub 1.9} electrolyte

Energy Technology Data Exchange (ETDEWEB)

Zhang, Xinge; Deces-Petit, Cyrille; Yick, Sing; Robertson, Mark; Kesler, Olivera; Maric, Radenka; Ghosh, Dave [Institute for Fuel Cell Innovation, National Research Council Canada, 3250 East Mall, Vancouver, BC (Canada V6T 1W5)

2006-11-08

In this study, an addition of Co oxide or Cu oxide to Sm{sub 0.2}Ce{sub 0.8}O{sub 1.9} (SDC) was studied to improve the sinterability of SDC. It has been found that both Co and Cu oxide are very effective as sintering aids, and the SDC sintering temperature can be reduced from 1400{sup o}C without aids to below 1000{sup o}C with only 1at.% of either Cu oxide or Co oxide. As compared to the pure SDC, a slight decrease of ionic conductivity was observed in SDC with Cu sintering aid. There is no obvious effect on electrochemical property of SDC with Co sintering aid under 2.5at.%. (author)

Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Annual Status Report for Fiscal Year 2006

Energy Technology Data Exchange (ETDEWEB)

R. P. Wells

2007-05-09

This report provides a status of the progress made in Fiscal Year 2006 on tasks identified in the Waste Area Group 10, Operable Unit 10-08, Remedial Investigation/Feasibility Study Work Plan. Major accomplishments include: (1) groundwater sampling and review of the groundwater monitoring data, (2) installation of a Sitewide groundwater-level monitoring network, (3) update of the Groundwater Monitoring and Field Sampling Plan of Operable Unit 10-08, (4) re-evaluation of the risk at Site TSF-08, (5) progress on the Operable Unit 10-08 Sitewide Groundwater Model.

Immobilization of lead in shooting range soils by means of cement, quicklime, and phosphate amendments.

Science.gov (United States)

Cao, Xinde; Dermatas, Dimitris; Xu, Xuanfeng; Shen, Gang

2008-03-01

Lead (Pb) contamination at shooting range sites is increasingly under environmental concern. Controlling Pb leachability from shooting range soil media is an important step to minimize Pb exposure to the surrounding environment. This study investigated stabilization of Pb in shooting range soils treated with cement, quicklime, and phosphate. Two soils were used and collected from two shooting ranges, referred to as SR1 and SR2. The treatment additives were applied to the soils at rates from 2.5% to 10% (w/w). The effectiveness of each treatment was evaluated by Pb (w/w). The effectiveness of each treatment was evaluated by Pb leachability, measured by the Toxicity Characteristic Leaching Procedure (TCLP). The possible mechanisms for Pb immobilization were elucidated using X-ray powder diffraction (XRPD). Cement and quicklime treatments were effective in immobilizing Pb in SR1 soil, with reduction of Pb concentration in TCLP leachate (TCLP-Pb) to be below the U.S. EPA non-hazardous regulatory limit of 5 mg L(-1) at application rates of > or =5% and 28-d incubation. By contrast, cement and quicklime amendments were less effective for Pb stabilization in SR2 soil because the TCLP-Pb levels in the treated soil were still higher than the limit of 5 mg L(-1) at all application rates, although they were significantly reduced in comparison with the untreated soil. Phosphate application was most effective in reducing Pb leach ing in both soils. Even at an application rate as low as 5% and 1-d incubation, phosphate could reduce TCLP-Pb to be below the limit of 5 mg L(-1) in both soils. Immobilization of Pb in the SR1 soil amended with cement and quicklime was attributed to the formation of pozzolanic minerals (e.g., calcium silicate hydrate C-S-H and ettringite) that could encapsulate soil Pb. The pozzolanic reaction was limited in the SR2 soil upon the application of cement and quicklime. Reduction of the TCLP-Pb might result from complexation of Pb on the surface of the

The effects of strain relaxation on the dielectric properties of epitaxial ferroelectric Pb(Zr0.2Ti0.8)TiO3 thin films

Science.gov (United States)

Khan, Asif Islam; Yu, Pu; Trassin, Morgan; Lee, Michelle J.; You, Long; Salahuddin, Sayeef

2014-07-01

We study the effects of strain relaxation on the dielectric properties of epitaxial 40 nm Pb(Zr0.2Ti0.8)TiO3 (PZT) films. A significant increase in the defect and dislocation density due to strain relaxation is observed in PZT films with tetragonality c/a fatigue in ferroelectric materials.

Assessment of Analytic Water hammer Pressure Model of FAI/08-70

International Nuclear Information System (INIS)

Park, Ju Yeop; Yoo, Seung Hun; Seul, Kwang-Won

2016-01-01

In evaluating water hammer effect on the safety related systems, methods developed by the US utility are likely to be adopted in Korea. For example, the US utility developed specific methods to evaluate pressure and loading transient on piping due to water hammer as in FAI/08-70. The methods of FAI/08-70 would be applied in Korea when any regulatory request on the evaluation of water hammer effect due to the non-condensable gas accumulation in the safety related systems. Specifically, FAI/08-70 gives an analytic model which can be used to analyze the maximum transient pressure and maximum transient loading on the piping of the safety-related systems due to the non-condensable induced water hammer effect. Therefore, it seems to be meaningful to review the FAI/08-70 methods and attempt to apply the methods to a specific case to see if they really give reasonable estimate before the application of FAI/08-70 methods to domestic nuclear power plants. In the present study, analytic water hammer pressure model of FAI/08-70 is reviewed in detail and the model is applied to the specific experiment of FAI/08-70 to see if the analytic water hammer pressure model really gives reasonable estimate of the peak water hammer pressure. Specifically, we assess the experiment 52A of FAI/08-70 which adopts flushed initial condition with a short rising piping length and a high level piping length of 51inch. The calculated analytic water hammer pressure peak shows a close agreement with the measured experimental data of 52A. Unfortunately, however, the theoretical value is a little bit less than that of the experimental value. This implies the analytic model of FAI/08-70 is not conservative

Assessment of Analytic Water hammer Pressure Model of FAI/08-70

Energy Technology Data Exchange (ETDEWEB)

Park, Ju Yeop; Yoo, Seung Hun; Seul, Kwang-Won [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2016-10-15

In evaluating water hammer effect on the safety related systems, methods developed by the US utility are likely to be adopted in Korea. For example, the US utility developed specific methods to evaluate pressure and loading transient on piping due to water hammer as in FAI/08-70. The methods of FAI/08-70 would be applied in Korea when any regulatory request on the evaluation of water hammer effect due to the non-condensable gas accumulation in the safety related systems. Specifically, FAI/08-70 gives an analytic model which can be used to analyze the maximum transient pressure and maximum transient loading on the piping of the safety-related systems due to the non-condensable induced water hammer effect. Therefore, it seems to be meaningful to review the FAI/08-70 methods and attempt to apply the methods to a specific case to see if they really give reasonable estimate before the application of FAI/08-70 methods to domestic nuclear power plants. In the present study, analytic water hammer pressure model of FAI/08-70 is reviewed in detail and the model is applied to the specific experiment of FAI/08-70 to see if the analytic water hammer pressure model really gives reasonable estimate of the peak water hammer pressure. Specifically, we assess the experiment 52A of FAI/08-70 which adopts flushed initial condition with a short rising piping length and a high level piping length of 51inch. The calculated analytic water hammer pressure peak shows a close agreement with the measured experimental data of 52A. Unfortunately, however, the theoretical value is a little bit less than that of the experimental value. This implies the analytic model of FAI/08-70 is not conservative.

Potentiometric NO2 Sensors Based on Thin Stabilized Zirconia Electrolytes and Asymmetric (La0.8Sr0.2)0.95MnO3 Electrodes

Science.gov (United States)

Zou, Jie; Zheng, Yangong; Li, Junliang; Zhan, Zhongliang; Jian, Jiawen

2015-01-01

Here we report on a new architecture for potentiometric NO2 sensors that features thin 8YSZ electrolytes sandwiched between two porous (La0.8Sr0.2)0.95MnO3 (LSM95) layers—one thick and the other thin—fabricated by the tape casting and co-firing techniques. Measurements of their sensing characteristics show that reducing the porosity of the supporting LSM95 reference electrodes can increase the response voltages. In the meanwhile, thin LSM95 layers perform better than Pt as the sensing electrode since the former can provide higher response voltages and better linear relationship between the sensitivities and the NO2 concentrations over 40–1000 ppm. The best linear coefficient can be as high as 0.99 with a sensitivity value of 52 mV/decade as obtained at 500 °C. Analysis of the sensing mechanism suggests that the gas phase reactions within the porous LSM95 layers are critically important in determining the response voltages. PMID:26205270

Pretreatment of Tc-Containing Waste and Its Effect on Tc-99 Leaching From Grouts

International Nuclear Information System (INIS)

Aloy, Albert; Kovarskaya, Elena N.; Harbour, John R.; Langton, Christine A.; Holtzscheiter, E. William

2007-01-01

A salt solution (doped with Tc-99), that simulates the salt waste stream to be processed at the Saltstone Production Facility, was immobilized in grout waste forms with and without (1) ground granulated blast furnace slag and (2) pretreatment with iron salts. The degree of immobilization of Tc-99 was measured through monolithic and crushed grout leaching tests. Although Fe (+2) was shown to be effective in reducing Tc-99 to the +4 state, the strong reducing nature of the blast furnace slag present in the grout formulation dominated the reduction of Tc-99 in the cured grouts. An effective diffusion coefficient of 4.75 x 10 -12 (Leach Index of 11.4) was measured using the ANSI/ANS-16.1 protocol. The leaching results show that, even in the presence of a concentrated salt solution, blast furnace slag can effectively reduce pertechnetate to the immobile +4 oxidation state. The measured diffusivity was introduced into a flow and transport model (PORFLOW) to calculate the release of Tc-99 from a Saltstone Vault as a function of hydraulic conductivity of the matrix. (authors)

Tailoring of K0.8Al0.7Fe0.15Si2.25O6 Leucite Based Dental Ceramic Material

Directory of Open Access Journals (Sweden)

Aleksandar Kremenović

2016-06-01

Full Text Available Potassium based ceramic materials composed from leucite in which 5 % of Al is exchanged with Fe and 4 % of hematite was synthesized by mechanochemical homogenization and annealing of K2O-SiO2-Al2O3-Fe2O3 mixtures. Synthesized material was characterized by X-ray Powder Diffraction (XRPD and Scanning Electron Microscopy coupled with Energy Dispersive X-ray spectroscopy (SEM/EDX. The two methods are in good agreement in regard to the specimen chemical composition suggesting that a leucite chemical formula is K0.8Al0.7Fe0.15Si2.25O6. Rietveld structure refinement results reveal that about 20 % of vacancies exist in the position of K atoms. This work is licensed under a Creative Commons Attribution 4.0 International License.

Oxygen tracer diffusion and surface exchange kinetics in Ba0.5Sr0.5Co0.8Fe0.2O3-δ

NARCIS (Netherlands)

Berenov, A.; Atkinson, A.; Kilner, J.; Ananyev, M.; Eremin, V.; Porotnikova, N.; Farlenkov, A.; Kurumchin, E.; Bouwmeester, Henricus J.M.; Bucher, E.; Sitte, W.

2014-01-01

The oxygen tracer diffusion coefficient, Db⁎, and the oxygen tracer surface exchange coefficient, k, were measured in Ba0.5Sr0.5Co0.8Fe0.2O3 − δ (BSCF5582) over the temperature range of 310–800 °C and the oxygen partial pressure range of 1.3 × 10−3–0.21 bar. Several measurement techniques were used:

Final report: survey and removal of radioactive surface contamination at environmental restoration sites, Sandia National Laboratories/New Mexico. Volume 2

International Nuclear Information System (INIS)

Lambert, K.A.; Mitchell, M.M.; Jean, D.; Brown, C.; Byrd, C.S.

1997-09-01

This report contains the Appendices A-L including Voluntary Corrective Measure Plans, Waste Management Plans, Task-Specific Health and Safety Plan, Analytical Laboratory Procedures, Soil Sample Results, In-Situ Gamma Spectroscopy Results, Radionuclide Activity Summary, TCLP Soil Sample Results, Waste Characterization Memoranda, Waste Drum Inventory Data, Radiological Risk Assessment, and Summary of Site-Specific Recommendations

Near-UV and blue wavelength excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} high efficiency red phosphors

Energy Technology Data Exchange (ETDEWEB)

Khanna, A. [Smart Lighting Engineering Research Center, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Dutta, P.S., E-mail: duttap@rpi.edu [Smart Lighting Engineering Research Center, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States); Electrical Computer and Systems Engineering, Rensselaer Polytechnic Institute, Troy, NY 12180 (United States)

2015-05-15

Red phosphors with narrow emission around 615 nm (with FWHM~5–10 nm) having chemical compositions of A{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} (A=Mg, Sr) have been found to exhibit the highest luminescence amongst the molybdate–tungstate family when excited by sources in the 380–420 nm wavelength range. Thus they are most suitable for enhancing color rendering index and lowering color temperature in phosphor converted white LEDs (pc-WLEDs) with near-UV/blue LED excitation sources. The excitation band edge in the near UV/blue wavelength in the reported phosphor has been attributed to the coordination environment of the transition metal ion (Mo{sup 6+}, W{sup 6+}) and host crystal structure. Furthermore the quantum efficiency of the phosphors has been enhanced by adjusting activator concentration, suitable compositional alloying using substitutional alkaline earth metal cations and charge compensation mechanisms. - Graphical abstract: The charge transfer excitation of orthorhombic Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} is significantly higher than tetragonal CaMoO{sub 4}: Eu{sup 3+} phosphors making Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} prime candidates for fabrication of warm white phosphor-converted LEDs. - Highlights: • LED excitable Mg{sub 0.6}Ca{sub 2.16}Mo{sub 0.2}W{sub 0.8}O{sub 6}: Eu{sub 0.12}{sup 3+}/Na{sub 0.12}{sup +} phosphors were synthesized. • These phosphors are 10 times more intense than CaMoO{sub 4}: Eu{sup 3+} red phosphors. • Their intensity and efficiency were enhanced by materials optimization techniques. • Such techniques include compositional alloying, charge compensation, etc.

Robustness of dynamic magnetism in the triangle-based antiferromagnets Ba3Ru1- x Ir x Ti2O9 ( x = 0.5 and 0.8)

Science.gov (United States)

Lee, W.-J.; Do, S.-H.; Lee, S.; Choi, Y.-S.; Choi, K.-Y.; Yoon, Sungwon; Suh, Byoungjin; Jang, Zeehoon

2018-01-01

We report on the spin dynamics of the strong spin-orbit coupled antiferromagnets Ba3Ru1- x Ir x Ti2O9 ( x = 0.5 and 0.8), which comprise a mixture of edge- and corner-sharing triangles. Muon spin-relaxation measurements give no hints of long-range magnetic order down to 25 mK. Rather, the muon spin-relaxation rates λ( T) show persistent spin dynamics below 1 K, indicating that fast fluctuations are dominant in spite of Ir4+( J eff = 1/2)/Ru4+( S = 1) randomness. The muon spin depolarization of both compounds is well described by a stretched exponential function with the stretching exponent β = 0.4 (0.6) for x = 0.5 (0.8) at low temperatures, which is larger than β = 1/3 expected for a spin glass. Our results suggest that randomness in the spin number and the exchange interaction induces a partial spin freezing, but the majority of spins remain dynamically fluctuating.

Nickel-doped (Zr0.8, Sn0.2)TiO4 for microwave and millimeter-wave applications

International Nuclear Information System (INIS)

Ioachim, A.; Banciu, M.G.; Toacsan, M.I.; Nedelcu, L.; Ghetu, D.; Alexandru, H.V.; Stoica, G.; Annino, G.; Cassettari, M.; Martinelli, M.

2005-01-01

(Zr 0.8 , Sn 0.2 )TiO 4 ternary compounds (ZST) have been prepared by conventional solid-state reaction from raw materials. The effects of such sintering parameters as sintering temperature, sintering time, and NiO addition on structural and dielectric properties were investigated. The material exhibits a dielectric constant ε r ∼36.0 and high values of the product Qf of the intrinsic quality factor Q and the frequency f from 32,170 to 50,000 at microwave frequencies. The dielectric loss tan δ values of ZST ceramics are decreased by low-level doping of NiO, while the temperature coefficient of the resonance frequency τ f takes values in the range -2 to +4 ppm/ deg. C. Investigations on whispering gallery modes revealed low dielectric loss in millimetre-wave domain. An intrinsic quality factor of 480 was measured at 115.6 GHz. Dielectric resonators and substrates of ZST material were manufactured. The dielectric properties make the ZST material very attractive to microwave and millimeter-wave applications, such as dielectric resonators, filters, planar antennas, hybrid microwave integrated circuits, etc

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1991-01-01

We used a mixture experimental design for determining a window of operability for a process at the Savannah River Site Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. 137 Cs will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach rate properties of the supernate grout, formed from various mixes of solidified salt waste, needed to be determined. The effective diffusion coefficients for NO 3 and Cr were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag and flyash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used

Rietveld refinement and dielectric studies of Bi{sub 0.8}Ba{sub 0.2}FeO{sub 3} ceramic

Energy Technology Data Exchange (ETDEWEB)

Kaswan, Kavita, E-mail: kaswan.kavita@gmail.com; Agarwal, Ashish; Sanghi, Sujata; Rangi, Manisha; Jangra, Sandhaya; Singh, Ompal [Department of Applied Physics, Guru Jambheshwar University of Science and Technology, Hisar 125001, Haryana (India)

2016-05-23

Polycrystalline Bi{sub 0.8}Ba{sub 0.2}FeO{sub 3} ceramic has been synthesized via conventional solid state reaction technique. The Rietveld refinement of x-ray powder diffraction revealed that the sample has a rhombohedral crystal structure (space group R3c). With increase in temperature, the values of dielectric constant (ϵ′) and dielectric loss (tan δ) are found to be increase at different frequencies which may be the result of increase in the number of charge carriers and their mobilities due to the thermal activation. Further the ac conductivity data is analyzed by using Jonscher’s universal power law. The values of frequency exponent ‘s’ lies in the range 0.2 ≤ s ≤ 0.7 and decreases with increase in temperature which can be explained on the basis of CBH (Correlated Barrier Height) model.

Peak effect and superconducting properties of SmFeAsO{sub 0.8}F{sub 0.2} wires

Energy Technology Data Exchange (ETDEWEB)

Chen, Y L; Cui, Y J; Yang, Y; Zhang, Y; Wang, L; Zhao, Y [Key Laboratory of Magnetic Levitation Technologies and Maglev Trains, Ministry of Education of China, and Superconductivity R and D Center (SRDC), Southwest Jiaotong University, Chengdu, Sichuan 610031 (China); Cheng, C H; Sorrell, C [School of Materials Science and Engineering, University of New South Wales, Sydney, NSW 2052 (Australia)], E-mail: yzhao@swjtu.edu.cn

2008-11-15

Ta-sheathed SmFeAsO{sub 0.8}F{sub 0.2} superconducting wires with T{sub c} = 52.5 K have been fabricated using the powder-in-tube (PIT) method and the superconducting properties of the wires have been investigated. The wires exhibit a very large intragrain critical current density at a temperature below 30 K. A peak effect with maximal J{sub c} = 0.6 MA cm{sup -2} at 10 K under 6 T field was observed. The peak field H{sub pear} is strongly temperature-dependent. A severe weak-link effect depresses the development of global supercurrent owing to a very short coherence length. The wires also show a power law temperature dependence for the irreversibility line with H{sub irr}{approx_equal}(1-T/T{sub c}){sup 1.5}. The H-T phase diagram was found to be similar to that of other superconducting cuprates.

High-strength uranium-0.8 weight percent titanium alloy penetrators

International Nuclear Information System (INIS)

Northcutt, W.G.

1978-09-01

Long-rod kinetic-energy penetrators, produced from a uranium-0.8 titanium (U-0.8 Ti) alloy, are normally water quenched from the gamma phase (approximately 800 0 C) and aged to the desired hardness and strength levels. High cooling rates from 800 0 C in U-0.8 Ti alloy cylindrical bodies larger than about 13 mm in diameter cause internal voids, while slower rates of cooling can produce material that is unresponsive to aging. For the present study, elimination of quenching voids was of paramount importance; therefore, a process including the quenching of plate was explored. Vacuum-induction-cast ingots were forged and rolled into plate and cut into blanks from which the penetrators were obtained. Quenched U-0.8 Ti alloy blanks were aged at 350 to 500 0 C to determine the treatment that would provide maximum tensile and impact strengths. Both tensile and impact strengths were maximized by aging in vacuum for six hours at 450 0 C

Mechanical behaviour of Br0.5Sr0.5Co0.8Fe0.2O3-δ under uniaxial compression

International Nuclear Information System (INIS)

Araki, Wakako; Malzbender, Jürgen

2013-01-01

The present study reports on the mechanical behaviour of Br 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3-δ under uniaxial compression at various temperatures. The stress–strain curve at room temperature shows a small but clear creep deformation, along with a hysteresis and a remnant strain, which could be related to a spin transition of cobalt. The hysteresis as well as Young’s modulus decrease with increasing temperature to 473 K, at which temperature the creep behaviour disappears. The material shows conventional high-temperature creep above 673 K

Physics at the FMQT’08 conference

NARCIS (Netherlands)

Špička, V.; Nieuwenhuizen, T.M.; Keefe, P.D.

2010-01-01

This paper summarizes the recent state of the art of the following topics presented at the FQMT’08 conference: Foundations of quantum physics, Quantum measurement; Quantum noise, decoherence and dephasing; Cold atoms and Bose-Einstein condensation; Physics of quantum computing and information;

Part II. Large scale applications of Ni{sub x}Mn{sub 0.8-x}Mg{sub 0.2}Fe{sub 2}O{sub 4}; 0.1 {<=} x {<=} 0.35 using laser irradiation

Energy Technology Data Exchange (ETDEWEB)

Ahmed, M.A., E-mail: moala1947@yahoo.com [Materials Science. Lab (1), Physics Department, Faculty of Science, Cairo University, Giza (Egypt); Bishay, Samiha T. [Department of Physics, Faculty of Girls for Art, Science and Education, Ain Shams University, Cairo (Egypt); El-dek, S.I.; Omar, G. [Materials Science. Lab (1), Physics Department, Faculty of Science, Cairo University, Giza (Egypt)

2011-07-28

Highlights: >X-ray diffractograms of Ni{sub x}Mn{sub 0.8-x}Mg{sub 0.2}Fe{sub 2}O{sub 4} samples before and after laser irradiation are characteristic of cubic spinel structure with better crystallinity after irradiation. > The crystal size of the ferrite increases after laser irradiation. > The main conduction mechanism in the investigated system is the correlated barrier hopping and it is the same before and laser irradiation. > The conductivity decreases after laser irradiation. - Abstract: Ni{sub x}Mn{sub 0.8-x}Mg{sub 0.2}Fe{sub 2}O{sub 4}; 0.1 {<=} x {<=} 0.35 was prepared by standard ceramic technique at sintering temperature 1200 deg. C using heating / cooling rate 4 deg. C/min. The samples were irradiated by Nd YAG pulsed laser with energy of the pulse 250 mJ. X-ray diffractograms reveal cubic spinel structure for all the samples before and after laser irradiation. After laser irradiation, better crystallinity was obtained in a form of an increase in the calculated crystal size. This increase was discussed as due to the change in the valence of some ions like Fe{sup 3+}, Ni{sup 2+} and Mn{sup 2+}. The conductivity of all the investigated samples decreases after laser irradiation and becomes temperature independent for a wider range than that before irradiation. This was ascribed to electron rearrangement after laser irradiation. Accordingly, these ferrites are recommended to be useful in electronic devices.

Maximum likelihood and Bayesian analyses of a combined nucleotide sequence dataset for genetic characterization of a novel pestivirus, SVA/cont-08.

Science.gov (United States)

Liu, Lihong; Xia, Hongyan; Baule, Claudia; Belák, Sándor

2009-01-01

Bovine viral diarrhoea virus 1 (BVDV-1) and Bovine viral diarrhoea virus 2 (BVDV-2) are two recognised bovine pestivirus species of the genus Pestivirus. Recently, a pestivirus, termed SVA/cont-08, was detected in a batch of contaminated foetal calf serum originating from South America. Comparative sequence analysis showed that the SVA/cont-08 virus shares 15-28% higher sequence identity to pestivirus D32/00_'HoBi' than to members of BVDV-1 and BVDV-2. In order to reveal the phylogenetic relationship of SVA/cont-08 with other pestiviruses, a molecular dataset of 30 pestiviruses and 1,896 characters, comprising the 5'UTR, N(pro) and E2 gene regions, was analysed by two methods: maximum likelihood and Bayesian approach. An identical, well-supported tree topology was observed, where four pestiviruses (SVA/cont-08, D32/00_'HoBi', CH-KaHo/cont, and Th/04_KhonKaen) formed a monophyletic clade that is closely related to the BVDV-1 and BVDV-2 clades. The strategy applied in this study is useful for classifying novel pestiviruses in the future.

Electronic conductivity of Ce(0.9)Gd(0.1)O(1.95-δ) and Ce(0.8)Pr(0.2)O(2-δ): Hebb-Wagner polarisation in the case of redox active dopants and interference

DEFF Research Database (Denmark)

Chatzichristodoulou, Christodoulos; Hendriksen, Peter Vang

2011-01-01

of the steady state I-V curve from the standard Hebb-Wagner equation was observed for the case of Ce(0.8)Pr(0.2)O(2-δ). It is shown that the I-V curve can be successfully reproduced when the presence of the redox active dopant, Pr(3+)/Pr(4+), is taken into account, whereas even better agreement can be reached...

Structural and electrochemical properties of La 0.8Sr 0.2Ga 1-xFe xO 3

Science.gov (United States)

Mori, Kazuhiro; Onodera, Yohei; Kiyanagi, Ryoji; Richardson, James W.; Itoh, Keiji; Sugiyama, Masaaki; Kamiyama, Takashi; Fukunaga, Toshiharu

2009-02-01

Mixed ionic-electronic conductor of Fe doped lanthanum gallate, La 0.8Sr 0.2Ga 1-xFe xO 3, has been studied by the dc four-probe method and the neutron powder diffraction. In the electrical conductivity measurement at RT, insulator-metal transition-like phenomenon was observed at around x˜0.35; this suggests an existence of the percolation limit for the electronic conductivity. Simultaneously, a bond length between O atoms, lO-O, in a MO 6 octahedron (M dbnd Ga 1-xFe x) drastically expands over x˜0.4, according to the result of crystal structure refinement based on the hexagonal phase. Such a drastic expansion in the lO-O would induce the decrease in the oxygen ionic conductivity.

Leaching Behavior of Selected Trace and Toxic Metals in Coal Fly Ash Samples Collected from Two Thermal Power Plants, India.

Science.gov (United States)

Sandeep, P; Sahu, S K; Kothai, P; Pandit, G G

2016-09-01

Studies on leaching behavior of metals associated with coal fly ash (FA) are of great concern because of possible contamination of the aquatic environment. In the present study, leaching behavior of metals (As, Se, Cr, Pb, V, Zn, etc.) in two different FA samples (FA1 and FA2) was investigated at various pH (2-12), temperatures of leachate solution and using TCLP. At pH 2, the highest leaching was observed for Fe (21.6 and 32.8 µg/g), whereas at pH 12, Arsenic was found to have the highest leaching (1.5 and 2.4 µg/g) in FA1 and FA2. Leachate solution temperature showed a positive effect on the metal's leachability. In TCLP, most of the metal's leachability was observed to be higher than that of batch leaching tests. The present study suggests that, leaching of As and Se from FA samples can moderately affect ground/surface water quality at the study locations.

40 CFR 600.510-08 - Calculation of average fuel economy.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 29 2010-07-01 2010-07-01 false Calculation of average fuel economy. 600.510-08 Section 600.510-08 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) ENERGY POLICY FUEL ECONOMY AND CARBON-RELATED EXHAUST EMISSIONS OF MOTOR VEHICLES Fuel Economy Regulations for Model Year 1978 Passenger Automobiles...

Mild hydrothermal synthesis, crystal structure, spectroscopic and magnetic properties of the [MxIIM2.5-xIII(H2O)2(HPIIIO3)y(PVO4)2-yF] [M=Fe, x=2.08, y=1.58; M=Co, Ni, x=2.5, y=2] compounds

International Nuclear Information System (INIS)

Orive, Joseba; Mesa, Jose L.; Legarra, Estibaliz; Plazaola, Fernando; Arriortua, Maria I.; Rojo, Teofilo

2009-01-01

The [M x II M 2.5-x III (H 2 O) 2 (HP III O 3 ) y (P V O 4 ) 2-y F] [M=Fe (1), x=2.08, y=1.58; M=Co (2), x=2.5, y=2; Ni (3), x=2.5, y=2] compounds have been synthesized using mild hydrothermal conditions at 170 deg. C during five days. Single-crystals of (1) and (2), and polycrystalline sample of (3) were obtained. These isostructural compounds crystallize in the orthorhombic system, space group Aba2, with a=9.9598(2), b=18.8149(4) and c=8.5751(2) A for (1), a=9.9142(7), b=18.570(1) and c=8.4920(5) A for (2) and a=9.8038(2), b=18.2453(2) and c=8.4106(1) A for (3), with Z=8 in the three phases. An X-ray diffraction study reveals that the crystal structure is composed of a three-dimensional skeleton formed by [MO 5 F] and [MO 4 F 2 ] (M=Fe, Co and Ni) octahedra and [HPO 3 ] tetrahedra, partially substituted by [PO 4 ] tetrahedra in phase (1). The IR spectra show the vibrational modes of the water molecules and those of the (HPO 3 ) 2- tetrahedral oxoanions. The thermal study indicates that the limit of thermal stability of these phases is 195 deg. C for (1) and 315 deg. C for (2) and (3). The electronic absorption spectroscopy shows the characteristic bands of the Fe(II), Co(II) and Ni(II) high-spin cations in slightly distorted octahedral geometry. Magnetic measurements indicate the existence of global antiferromagnetic interactions between the metallic centers with a ferromagnetic transition in the three compounds at 28, 14 and 21 K for (1), (2) and (3), respectively. Compound (1) exhibits a hysteresis loop with remnant magnetization and coercive field values of 0.72 emu/mol and 880 Oe, respectively. - Abstract: Polyhedral view of the crystal structure of the [M x II M 2.5-x III (H 2 O) 2 (HP III O 3 ) y (P IV O 4 ) 2-y F] [M=Fe, x=2.08, y=1.58; M=Co, Ni, x=2.5, y=2] compounds showing the sheets along the [001] direction.

Structural, magnetic and optical characterization of Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} nano particles prepared by co-precipitation method

Energy Technology Data Exchange (ETDEWEB)

Kannan, Y.B., E-mail: ybkans@gmail.com [Department of Physics, Arumugam Pillai Seethai Ammal College, Tiruppattur 630211 (India); Saravanan, R. [Research Centre & PG Department of Physics, The Madura College, Madurai 625011 (India); Srinivasan, N. [Research Centre & PG Department of Physics, Thiagarajar College, Madurai 625009 (India); Praveena, K. [School of Physics, Univeristy of Hyderabad, Hyderabad 500046 (India); Sadhana, K. [Material Research Center, Indian Institute of Science, Bangalore 560012 (India)

2016-12-01

Bond strength values, between tetrahedral sites and octahedral sites atoms in the unit cell, are evaluated using maximum entropy method (MEM) for the Ni{sub 0.8}Zn{sub 0.2}Fe{sub 2}O{sub 4} nano ferrite particles, prepared by co-precipitation method and sintered at 900 °C. The spinel structure is confirmed from the XRD analysis done using the Rietveld method. Substitution of zinc ion causes increase in lattice parameter value. Thermal behavior, morphology, magnetic properties and optical band gap energy values of the sample are determined by using thermogravimetric analysis and differential thermal analysis, scanning electron microscope, vibrating sample magnetometer and UV–VIS–NIR techniques respectively. Low value of saturation magnetization is attributed to the disorder in cation distribution.

Solvothermal coating LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} microspheres with nanoscale Li{sub 2}TiO{sub 3} shell for long lifespan Li-ion battery cathode materials

Energy Technology Data Exchange (ETDEWEB)

Wu, Naiteng; Wu, Hao; Liu, Heng; Zhang, Yun, E-mail: y_zhang@scu.edu.cn

2016-04-25

LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} (NCA) microspheres covered by a nanoscale Li{sub 2}TiO{sub 3}-based shell were synthesized by a facile strategy based on a solvothermal pre-coating treatment combined with a post-sintering lithiation process. The morphology, structure and composition of the Li{sub 2}TiO{sub 3}-coated NCA samples were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning scanning electron microscope (SEM) with an energy-dispersive X-ray spectroscope (EDS), and transmission electron microscopy (TEM). Owing to the complete, uniform and nanoscale Li{sub 2}TiO{sub 3} coating shell, the resultant surface-modified NCA microspheres used as Li-ion battery cathode materials manifest remarkably enhanced cycling performances, attaining 94% and 84% capacity retention after 200 and 400 cycles at 0.5 C, respectively, which is much better than the pristine NCA counterpart (60% retention, 200 cycles). More impressively, the surface-modified NCA also shows an intriguing storage stability. After being stored at 30 °C for 50 days, the coated NCA-based cells are subjected to be cycled both at room and elevated temperatures, in which the aged cells can still remain 84% capacity retention after 200 cycles at 25 °C and 77% capacity retention after 200 cycles at 55 °C, respectively. All these results demonstrate that the Li{sub 2}TiO{sub 3}-coated LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} microsphere is a promising cathode material for Li-ion batteries with long lifespan. - Graphical abstract: Nanoscale Li{sub 2}TiO{sub 3}-based shell encapsulated LiNi{sub 0.8}Co{sub 0.15}Al{sub 0.05}O{sub 2} (NCA) microspheres are fabricated through a solvothermal pre-coating treatment combined with post-lithiation process. The surface-coated NCA as cathode materials shows a remarkably enhanced cycling performance and storage stability for long lifespan Li-ion batteries. - Highlights: • Li{sub 2}TiO{sub 3} is used as coating

Degradation of dibenzofuran via multiple dioxygenation by a newly isolated Agrobacterium sp. PH-08.

Science.gov (United States)

Le, T T; Murugesan, K; Nam, I-H; Jeon, J-R; Chang, Y-S

2014-03-01

To demonstrate the biodegradation of dibenzofuran (DF) and its structural analogs by a newly isolated Agrobacterium sp. PH-08. To assess the biodegradation potential of newly isolated Agrobacterium sp. PH-08, various substrates were evaluated as sole carbon sources in growth and biotransformation experiments. ESI LC-MS/MS analysis revealed the presence of angular degrading by-products as well as lateral dioxygenation metabolites in the upper pathway. The metabolites in the lower pathway also were detected. In addition, the cometabolically degraded daughter compounds of DF-related compounds such as BP and dibenzothiophene (DBT) in dual substrate degradation were observed. Strain PH-08 exhibited the evidence of meta-cleavage pathway as confirmed by the activity and gene expression of catechol-2,3-dioxygenase. Newly isolated bacterial strain, Agrobacterium sp. PH-08, grew well with and degraded DF via both angular and lateral dioxygenation as demonstrated by metabolites identified through ESI LC-MS/MS and GC-MS analyses. The other heterocyclic pollutants were also cometabolically degraded. Few reports have described the complete degradation of DF by a cometabolic lateral pathway. Our study demonstrates the novel results that the newly isolated strain utilized the DF as a sole carbon source and mineralized it via multiple dioxygenation. © 2013 The Society for Applied Microbiology.

Microstructure and magnetic properties of nanostructured (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} alloy produced by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Boukherroub, N. [UR-MPE, M' hamed Bougara University, Boumerdes 35000 (Algeria); Guittoum, A., E-mail: aguittoum@gmail.com [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Laggoun, A. [UR-MPE, M' hamed Bougara University, Boumerdes 35000 (Algeria); Hemmous, M. [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Martínez-Blanco, D. [SCTs, University of Oviedo, EPM, 33600 Mieres (Spain); Blanco, J.A. [Department of Physics, University of Oviedo, Calvo Sotelo St., 33007 Oviedo (Spain); Souami, N. [Nuclear Research Centre of Algiers, 02 Bd Frantz Fanon, BP 399 Alger-Gare, Algiers (Algeria); Gorria, P. [Department of Physics and IUTA, EPI, University of Oviedo, 33203 Gijón (Spain); Bourzami, A. [Laboratoire d' Etudes des Surfaces et Interfaces des Matériaux Solides (LESIMS), Université Sétif1, 19000 Sétif (Algeria); Lenoble, O. [Institut Jean Lamour, CNRS-Université de Lorraine, Boulevard des aiguillettes, BP 70239, F-54506 Vandoeuvre lès Nancy (France)

2015-07-01

We report on how the microstructure and the silicon content of nanocrystalline ternary (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} powders (x=0, 5, 10, 15 and 20 at%) elaborated by high energy ball milling affect the magnetic properties of these alloys. The formation of a single-phase alloy with body centred cubic (bcc) crystal structure is completed after 72 h of milling time for all the compositions. This bcc phase is in fact a disordered Fe(Al,Si) solid solution with a lattice parameter that reduces its value almost linearly as the Si content is increased, from about 2.9 Å in the binary Fe{sub 80}Al{sub 20} alloy to 2.85 Å in the powder with x=20. The average nanocrystalline grain size also decreases linearly down to 10 nm for x=20, being roughly half of the value for the binary alloy, while the microstrain is somewhat enlarged. Mössbauer spectra show a sextet thus suggesting that the disordered Fe(Al,Si) solid solution is ferromagnetic at room temperature. However, the average hyperfine field diminishes from 27 T (x=0) to 16 T (x=20), and a paramagnetic doublet is observed for the powders with higher Si content. These results together with the evolution of both the saturation magnetization and the coercive field are discussed in terms of intrinsic and extrinsic properties. - Highlights: • Single-phase nanocrystalline (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} (x=0, 5, 10, 15 and 20 at%) powders were successfully fabricated by mechanical alloying for a milling time of 72 h. • The insertion of Si atoms leads to a unit-cell contraction and a decrease in the average crystallite size. • The hyperfine and magnetic properties of (Fe{sub 0.8}Al{sub 0.2}){sub 100–x}Si{sub x} were influenced by the Si content.

A Special Extract of Bacopa monnieri (CDRI-08 Restores Learning and Memory by Upregulating Expression of the NMDA Receptor Subunit GluN2B in the Brain of Scopolamine-Induced Amnesic Mice

Directory of Open Access Journals (Sweden)

Rakesh Rai

2015-01-01

Full Text Available In the present communication, we have investigated effects of the CDRI-08, a well characterized extract of Bacopa monnieri, on expression of the GluN2B subunit of NMDAR in various brain regions of the scopolamine-induced amnesic mice. Our behavioral data reveal that scopolamine-treated amnesic mice exhibit significant decline in the spatial memory compared to the normal control mice. Our RT-PCR and immunoblotting data revealed that the scopolamine treatment resulted in a significant downregulation of the NMDAR GluN2B subunit expression in prefrontal cortex and hippocampus. Our enzyme assay data revealed that scopolamine caused a significant increase in the acetylcholinesterase activity in both the brain regions. Further, oral administration of the CDRI-08 to scopolamine-treated amnesic mice restored the spatial memory which was found to be associated with significant upregulation of the GluN2B subunit expression and decline in the acetylcholinesterase activity in prefrontal cortex as well as hippocampus towards their levels in the normal control mice. Our study provides the evidence for the mechanism underlying role of the Bacopa monnieri extract (CDRI-08 in restoring spatial memory in amnesic mice, which may have therapeutic implications.

Exploring the luminosity evolution and stellar mass assembly of 2SLAQ luminous red galaxies between redshifts 0.4 and 0.8

Science.gov (United States)

Banerji, Manda; Ferreras, Ignacio; Abdalla, Filipe B.; Hewett, Paul; Lahav, Ofer

2010-03-01

We present an analysis of the evolution of 8625 luminous red galaxies (LRGs) between z = 0.4 and 0.8 in the 2dF and Sloan Digital Sky Survey LRG and QSO (2SLAQ) survey. The LRGs are split into redshift bins and the evolution of both the luminosity and stellar mass function with redshift is considered and compared to the assumptions of a passive evolution scenario. We draw attention to several sources of systematic error that could bias the evolutionary predictions made in this paper. While the inferred evolution is found to be relatively unaffected by the exact choice of spectral evolution model used to compute K + e corrections, we conclude that photometric errors could be a source of significant bias in colour-selected samples such as this, in particular when using parametric maximum likelihood based estimators. We find that the evolution of the most massive LRGs is consistent with the assumptions of passive evolution and that the stellar mass assembly of the LRGs is largely complete by z ~ 0.8. Our findings suggest that massive galaxies with stellar masses above 1011Msolar must have undergone merging and star formation processes at a very early stage (z >~ 1). This supports the emerging picture of downsizing in both the star formation as well as the mass assembly of early-type galaxies. Given that our spectroscopic sample covers an unprecedentedly large volume and probes the most massive end of the galaxy mass function, we find that these observational results present a significant challenge for many current models of galaxy formation.

Statistical experimental design for saltstone mixtures

International Nuclear Information System (INIS)

Harris, S.P.; Postles, R.L.

1992-01-01

The authors used a mixture experimental design for determining a window of operability for a process at the U.S. Department of Energy, Savannah River Site, Defense Waste Processing Facility (DWPF). The high-level radioactive waste at the Savannah River Site is stored in large underground carbon steel tanks. The waste consists of a supernate layer and a sludge layer. Cesium-137 will be removed from the supernate by precipitation and filtration. After further processing, the supernate layer will be fixed as a grout for disposal in concrete vaults. The remaining precipitate will be processed at the DWPF with treated waste tank sludge and glass-making chemicals into borosilicate glass. The leach-rate properties of the supernate grout formed from various mixes of solidified coefficients for NO 3 and chromium were used as a measure of leach rate. Various mixes of cement, Ca(OH) 2 , salt, slag, and fly ash were used. These constituents comprise the whole mix. Thus, a mixture experimental design was used. The regression procedure (PROC REG) in SAS was used to produce analysis of variance (ANOVA) statistics. In addition, detailed model diagnostics are readily available for identifying suspicious observations. For convenience, trillinear contour (TLC) plots, a standard graphics tool for examining mixture response surfaces, of the fitted model were produced using ECHIP

Raman Scattering in La0.2Sr0.8FeO3-δ thin film: annealing-induced reduction and phase transformation

Science.gov (United States)

Islam, Mohammad; Xie, Yujun; Scafetta, Mark; May, Steven; Spanier, Jonathan

2015-03-01

Raman scattering in thin film La0.2Sr0.8FeO3-δ on MgO(001) collected at 300 K following different stages of annealing at selected temperatures (300 K topotactic transformation of the crystal structure from that of the rhombohedral ABO3 perovskites to that of Brownmillerite-like structure consisting of octahedrally and tetrahedrally coordinated Fe atoms. We acknowledge the ONR (N00014-11-1-0664), the Drexel Centralized Research Facilities, the Army Research Office DURIP program, the Department of Education (GAANN-RETAIN, Award No. P200A100117), and Leszek Wielunski at Rutgers University.

Vibrational localized motions of hydrogen in the storage compound Ti0.8 Zr0.2 CrMnH3 studied by slow neutron inelastic scattering

International Nuclear Information System (INIS)

Mestnik Filho, J.; Vinhas, L.A.

1988-08-01

The vibrational localized motions of hydrogen in the storage compound Ti 0.8 Zr 0.2 CrMnH 3 have been studied by slow neutron scattering, utilizing a berilium-filter-time-of-flight spectrometer. An energy distribution, consisting of therre peaks 50 MeV wide (FWHM), corresponding to the energy transfer of 85, 115 and 141 MeV has been observed and was attributed to hydrogen localized vibrations in three types of interstices which differs in composition of Ti and Zr atoms. From the analysis of the observed peaks intensities, it was concluded that the lowest measured hydrogen vibrational frequency is correlated with interstices that are rich in zirconium atoms whereas the highest frequency is due o interstices rich in titanium atoms. Therefore the larger radius of the the Zr atoms leads to the formation of interstices with larger intersticial hole sizes, which, in turn, makes possible the absorption of hydrogen in this compound, in contrast to an isostructural compound which contains only atoms with smaller radii, like Ti, in place of the atomic group Ti 0.8 Zr 0.2 . (author) [pt

Lattice defects in semiconducting Hg/1-x/Cd/x/Te alloys. I - Defect structure of undoped and copper doped Hg/0.8/Cd/0.2/Te. II - Defect structure of indium-doped Hg/0.8/Cd/0.2/Te

Science.gov (United States)

Vydyanath, H. R.

1981-01-01

Hall effect and mobility measurements were conducted on undoped Hg(0.8)Cd(0.2)Te crystals which were quenched to room temperature after being subjected to equilibration at temperatures ranging from 400 to 655 C in various Hg atmospheres. The variation of the hole concentration in the cooled crystals at 77 K as a function of Hg's partial pressure at the equilibration temperature, together with a comparison of the hole mobility in the undoped samples with that in copper-doped ones, yields a defect model for the undoped crystals according to which they are intrinsic at the equilibration temperatures and the native acceptor defects are doubly ionized. In the second part of this paper, the effects of indium doping are considered. The concentration of electrons obtained in the cooled crystals was found to be lower than the intrinsic carrier concentration at the equilibration temperatures. A defect model is proposed according to which most of the indium is incorporated as In2Te3(s) dissolved in the crystal, with only a small fraction of indium acting as single donors occupying Hg lattice sites.

Neutron diffraction and low temperature magnetization study of Tb0.8Y0.2MnO3

International Nuclear Information System (INIS)

Chakraborty, Keka R.; Mukadam, M.; Yusuf, S.M.; Shukla, R.; Tyagi, A.K.; Kaushik, S.D.; Siruguri, V.

2012-01-01

Multiferroic materials possess mutually correlated magnetic and electric order parameters which are suitable for device applications but scarcity of such materials and the separation of magnetic and electric ordering temperatures are a major hindrance in technological applications. TbMnO 3 is one of the material which is reported to have higher magnetoelectric coupling. Structurally, TbMnO 3 crystallizes in orthorhombically distorted perovskite structure (space group Pbnm). For TbMnO 3 , several reports are available in the literature which further modify the magnetoelectric coupling by selective doping or reducing the particle size to nano dimensions, or preparing thin films. Here, we study the effect of Y doping at Tb site in nanoparticle form in terms of crystal structure and magnetic properties. Nanoparticles of Tb 0.8 Y 0.2 MnO 3 were synthesized using the gel combustion technique. Crystal structure of this sample is studied at 300 K using neutron diffraction

Vortex dynamics and irreversibility line in optimally doped SmFeAsO0.8F0.2 from ac susceptibility and magnetization measurements

Science.gov (United States)

Prando, G.; Carretta, P.; de Renzi, R.; Sanna, S.; Palenzona, A.; Putti, M.; Tropeano, M.

2011-05-01

Ac susceptibility and static magnetization measurements were performed in the optimally doped SmFeAsO0.8F0.2 superconductor. The field-temperature phase diagram of the superconducting state was drawn, and, in particular, the features of the flux lines were derived. The dependence of the intragrain depinning energy on the magnetic field intensity was derived in the thermally activated flux-creep framework, enlightening a typical 1/H dependence in the high-field regime. The intragrain critical current density was extrapolated in the zero-temperature and zero-magnetic-field limit, showing a remarkably high value Jc0(0)~2×107 A/cm2, which demonstrates that this material is rather interesting for potential future technological applications.

Experimental study on the ionizing radiation field in absorbers irradiated by the 0.8 GeV and 1.2 GeV electrons

International Nuclear Information System (INIS)

Ambrosimov, V.K.; Kalmykov, N.N.; Kovalenko, G.D.

1987-01-01

The measurement results of spatial distribution of aluminium detector energy release and radioactivity in absorbers irradiated by 0.8 and 1.2 GeV electrons are given. Absorbers are made of aluminium, iron and lead, 30x30 cm size across the thickness is about 18 radiation length units. Thermoluminescence dosimeters LiF and radiochromium film dosimeters have been used to measure energy release. Induced activity of 18 F and 24 Na nuclides is determined in aluminium detectors. The experimental data are compared with the results of calculation carried out by the Monte-Carlo method

SiO{sub 2} effect on spectral and colorimetric properties of europium doped SrO{sub 2}-MgO-xSiO{sub 2} (0.8 {<=} x {<=} 1.6) phosphor for white LEDs

Energy Technology Data Exchange (ETDEWEB)

Chen, B J; Jang, K W; Lee, H S; Jayasimhadri, M; Cho, E J [Department of Physics, Changwon National University, Changwon, 641-773 (Korea, Republic of); Yi, S S [Department of Photonics, Silla University, Pusan 617-736 (Korea, Republic of); Jeong, J H [Department of Physics, Pukyong National University, Pusan 608-737 (Korea, Republic of)], E-mail: kwjang@changwon.ac.kr

2009-05-21

Silicate phosphors with compositions 1.99 SrO{sub 2}-1.0 MgO-xSiO{sub 2}-0.01 Eu{sub 2}O{sub 3} (x = 0.8, 1.0, 1.2, 1.4 and 1.6) were prepared in a reducing atmosphere via a solid state reaction. The resultant phosphors were examined by using x-ray diffraction and confirmed to be a mixture of monoclinic Sr{sub 2}SiO{sub 4} and orthorhombic Mg{sub 2}(Si{sub 2}O{sub 4}). The scanning electron microscope images revealed that SiO{sub 2} content does not influence the morphology of the resultant phosphors. It was also observed that the excitation spectra are dependent on the monitored emission wavelength, and the emission spectra are dependent on the excitation wavelength and the SiO{sub 2} content. The energy transfer between Eu{sup 2+} ions occupying different Sr{sup 2+} sites was discussed. The colour coordinates for these phosphors are tunable based on both the excitation wavelength and the SiO{sub 2} content.

The effect of MgO doping on the structure, magnetic and magnetotransport properties of La0.8Sr0.2MnO3 composite

International Nuclear Information System (INIS)

Aezami, A.; Eshraghi, M.; Kameli, P.; Salamati, H.

2007-01-01

Full text: The recent observation of anomalously Colossal Magnetoresistance (CMR) in the La 1-x A x MnO 3 (A = Sr, Ca, Ba or vacancies) system, has spurred renewed interest in studying these doped perovskite manganites. The properties of these materials are explained by double exchange theory of Zener and electron lattice interaction. However, the intrinsic CMR effect in the perovskite manganites is found on a magnetic field scale of several teslas and a narrow temperature range. It was found that, the presence of grain boundaries in polycrystalline samples leads to a large Low Field Magnetoresistance (LFMR) effect over a wide temperature range below the Curie temperature Tc. To achieve LFMR, different properties are considered. One of them is mixing of these CMR materials with secondary insulator phases. In this work, La 0.8 Sr 0.2 MnO 3 (LSMO) was selected as matrix material and MgO as a dopant. The La 0.8 Sr 0.2 MnO 3/x MgO samples with x= 0, 1, 2, 3, 5 and 7.5 Wt.% were prepared by Solid State Reaction method. Studies show that most part of the MgO goes into the perovskite lattice and Mg substituted Mn in LSMO and remainder segregates as a separate phase at the grain boundaries. Results also show that the value of MR decreases for all the doping levels. It seems that, due to the almost same ionic radii of Mg2+ and Mn2+, and at the higher sintering temperature, Mg2+ mostly replaced Mn3+ and weakens double exchange interaction. This speculation has been confirmed by XRD, SEM, susceptibility, resistivity and magnetoresistance analysis and measurements. (authors)

Effect of the temperature, strain rate and microstructure on flow and fracture characteristics of Ti-45Al-2Nb-2Mn+0.8vol.% TiB2 XD alloy

Science.gov (United States)

Erice, B.; Pérez-Martín, M. J.; Cendón, D. A.; Gálvez, F.

2012-05-01

A series of quasi-static and dynamic tensile tests at varying temperatures were carried out to determine the mechanical behaviour of Ti-45Al-2Nb-2Mn+0.8vol.% TiB2 XD as-HIPed alloy. The temperature for the tests ranged from room temperature to 850 ∘C. The effect of the temperature on the ultimate tensile strength, as expected, was almost negligible within the selected temperature range. Nevertheless, the plastic flow suffered some softening because of the temperature. This alloy presents a relatively low ductility; thus, a low tensile strain to failure. The dynamic tests were performed in a Split Hopkinson Tension Bar, showing an increase of the ultimate tensile strength due to the strain rate hardening effect. Johnson-Cook constitutive relation was used to model the plastic flow. A post-testing microstructural of the specimens revealed an inhomogeneous structure, consisting of lamellar α2 + γ structure and γ phase equiaxed grains in the centre, and a fully lamellar structure on the rest. The assessment of the duplex-fully lamellar area ratio showed a clear relationship between the microstructure and the fracture behaviour.

AC conductivity and dielectric properties of Ti-doped CoCr{sub 1.2}Fe{sub 0.8}O{sub 4} spinel ferrite

Energy Technology Data Exchange (ETDEWEB)

Elkestawy, M.A., E-mail: mkestawy@hotmail.co [Physics Department, Faculty of Science, Suez Canal University, Suez (Egypt); Abdel kader, S.; Amer, M.A. [Physics Department, Faculty of Science, Tanta University, Tanta (Egypt)

2010-01-15

Dielectric properties of spinel ferrite samples Co{sub 1+x}Ti{sub x}Cr{sub 1.2-2x}Fe{sub 0.8}O{sub 4} (0<=x<=0.5) were investigated as a function of frequency at different temperatures using a complex impedance technique. Also Cole-Cole diagrams of both permittivity and electric modulus were investigated at different temperatures to have an insight into the electric nature of the studied solids. It has been found that the electric modulus M* is the dominating property clarifying the intrinsic picture of these polycrystalline ferrites. The low conductivity and loss factor values indicate that the studied compositions may be good candidates for practical applications.

Demonstration of New Technologies Required for the Treatment of Mixed Waste Contaminated with {ge}260 ppm Mercury

Energy Technology Data Exchange (ETDEWEB)

Morris, M.I.

2002-02-06

The Resource Conservation and Recovery Act (RCRA) defines several categories of mercury wastes, each of which has a defined technology or concentration-based treatment standard, or universal treatment standard (UTS). RCRA defines mercury hazardous wastes as any waste that has a TCLP value for mercury of 0.2 mg/L or greater. Three of these categories, all nonwastewaters, fall within the scope of this report on new technologies to treat mercury-contaminated wastes: wastes as elemental mercury; hazardous wastes with less than 260 mg/kg [parts per million (ppm)] mercury; and hazardous wastes with 260 ppm or more of mercury. While this report deals specifically with the last category--hazardous wastes with 260 ppm or more of mercury--the other two categories will be discussed briefly so that the full range of mercury treatment challenges can be understood. The treatment methods for these three categories are as follows: Waste as elemental mercury--RCRA identifies amalgamation (AMLGM) as the treatment standard for radioactive elemental mercury. However, radioactive mercury condensates from retorting (RMERC) processes also require amalgamation. In addition, incineration (IMERC) and RMERC processes that produce residues with >260 ppm of radioactive mercury contamination and that fail the RCRA toxicity characteristic leaching procedure (TCLP) limit for mercury (0.20 mg/L) require RMERC, followed by AMLGM of the condensate. Waste with <260 ppm mercury--No specific treatment method is specified for hazardous wastes containing <260 ppm. However, RCRA regulations require that such wastes (other than RMERC residues) that exceed a TCLP mercury concentration of 0.20 mg/L be treated by a suitable method to meet the TCLP limit for mercury of 0.025 mg/L. RMERC residues must meet the TCLP value of {ge}0.20 mg/L, or be stabilized and meet the {ge}0.025 mg/L limit. Waste with {ge}260 ppm mercury--For hazardous wastes with mercury contaminant concentrations {ge}260 ppm and RCRA

THE APPLICATION OF NATURAL ZEOLITE FROM CIAMIS AS TiO2 PHOTOCATALYST SUPPORT FOR RHODAMINE B DYE PHOTODEGRADATION

Directory of Open Access Journals (Sweden)

Intan Cahaya Dani

2016-04-01

Full Text Available Heavy metals such as nickel and cadmium from the waste of human activities (industry, domestic, can lead the pollution and sediments deposited on the seabed. Water pH changing, can lead to the release (leaching metals in the sediment into the water body and then it will be bioaccumulated on biota arround the environment. To see the effect of pH changing on the release (leaching of these metals, extracting the sediment at pH variations has done (TCLP method. From the results of detection metals cadmium (Cd and nickel (Ni release studies, to see the hazards of cadmium and nickel metal, carried out a simulation of bioaccumulation test on biota using bioindikator Cyprinus carpio (OECD Guideline 305. Based on the analysis of data obtained in the nickel content in the sediment extract pH 3, 5 and 7 reached 2.55 to 27.94 µg/g, while for cadmium reaches 4.31 to 4.68 µg/g. Observation of metallic nickel and cadmium bioaccumulation in fish hass done for 28 days by looking at levels of cadmium and nickel on the gills of fish and meat. In the flesh of fish, the highest cadmium concentration of 3.179 µg/g while in the gills is 5.392 µg/g. The highest nickel concentrations in fish flesh is equal to 4.557 µg/g while for gill is equal to 10.417 µg/g. The study results indicate the presence of cadmium and nickel metal accumulation on biota.   Keywords: TCLP method, biota, Cyprinus carpio

CMS results in the Combined Computing Readiness Challenge CCRC'08

International Nuclear Information System (INIS)

Bonacorsi, D.; Bauerdick, L.

2009-01-01

During February and May 2008, CMS participated to the Combined Computing Readiness Challenge (CCRC'08) together with all other LHC experiments. The purpose of this worldwide exercise was to check the readiness of the Computing infrastructure for LHC data taking. Another set of major CMS tests called Computing, Software and Analysis challenge (CSA'08) - as well as CMS cosmic runs - were also running at the same time: CCRC augmented the load on computing with additional tests to validate and stress-test all CMS computing workflows at full data taking scale, also extending this to the global WLCG community. CMS exercised most aspects of the CMS computing model, with very comprehensive tests. During May 2008, CMS moved more than 3.6 Petabytes among more than 300 links in the complex Grid topology. CMS demonstrated that is able to safely move data out of CERN to the Tier-1 sites, sustaining more than 600 MB/s as a daily average for more than seven days in a row, with enough headroom and with hourly peaks of up to 1.7 GB/s. CMS ran hundreds of simultaneous jobs at each Tier-1 site, re-reconstructing and skimming hundreds of millions of events. After re-reconstruction the fresh AOD (Analysis Object Data) has to be synchronized between Tier-1 centers: CMS demonstrated that the required inter-Tier-1 transfers are achievable within a few days. CMS also showed that skimmed analysis data sets can be transferred to Tier-2 sites for analysis at sufficient rate, regionally as well as inter-regionally, achieving all goals in about 90% of >200 links. Simultaneously, CMS also ran a large Tier-2 analysis exercise, where realistic analysis jobs were submitted to a large set of Tier-2 sites by a large number of people to produce a chaotic workload across the systems, and with more than 400 analysis users in May. Taken all together, CMS routinely achieved submissions of 100k jobs/day, with peaks up to 200k jobs/day. The achieved results in CCRC'08 - focussing on the distributed

Development of an accelerated leaching method for incineration bottom ash correlated to toxicity characteristic leaching protocol.

Science.gov (United States)

Lin, Shengxuan; Zhou, Xuedong; Ge, Liya; Ng, Sum Huan; Zhou, Xiaodong; Chang, Victor Wei-Chung

2016-10-01

Heavy metals and some metalloids are the most significant inorganic contaminants specified in toxicity characteristic leaching procedure (TCLP) in determining the safety of landfills or further utilization. As a consequence, a great deal of efforts had been made on the development of miniaturized analytical devices, such as Microchip Electrophoresis (ME) and μTAS for on-site testing of heavy metals and metalloids to prevent spreading of those pollutants or decrease the reutilization period of waste materials such as incineration bottom ash. However, the bottleneck lied in the long and tedious conventional TCLP that requires 18 h of leaching. Without accelerating the TCLP process, the on-site testing of the waste material leachates was impossible. In this study, therefore, a new accelerated leaching method (ALM) combining ultrasonic assisted leaching with tumbling was developed to reduce the total leaching time from 18 h to 30 min. After leaching, the concentrations of heavy metals and metalloids were determined with ICP-MS or ICP-optical emission spectroscopy. No statistical significance between ALM and TCLP was observed for most heavy metals (i.e., cobalt, manganese, mercury, molybdenum, nickel, silver, strontium, and tin) and metalloids (i.e., arsenic and selenium). For the heavy metals with statistical significance, correlation factors derived between ALM and TCLP were 0.56, 0.20, 0.037, and 0.019 for barium, cadmium, chromium, and lead, respectively. Combined with appropriate analytical techniques (e.g., ME), the ALM can be applied to rapidly prepare the incineration bottom ash samples as well as other environmental samples for on-site determination of heavy metals and metalloids. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Liisinguandja kulude hüvitamise nõue kui liisingulepingu ülesütlemise üks tagajärg. Riigikohtu tsiviilkolleegiumi otsus asjas 3-2-1-33-08 / Sirje Saan

Index Scriptorium Estoniae

Saan, Sirje

2008-01-01

Riigikohtu lahendist 3-2-1-33-08 (OÜ Moneta ja Jaanus Jakobson kassatsioonkaebus Tallinna Ringkonnakohtu 21.12.2007. a otsusele AS Hansa Liising Eesti hagis OÜ Moneta, Janek Reinomägi ja Jaanus Jakobsoni vastu 1 222 326 .97 krooni saamiseks)

Structural investigation and microwave characteristics of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing materials

Energy Technology Data Exchange (ETDEWEB)

Manaf, Azwar [Dept. of Physics, Faculty of Mathematics and Natural Sciences, Indonesia of University (Indonesia); Adi, Wisnu Ari, E-mail: dwisnuaa@batan.go.id [Center for Technology of Nuclear Industry Material, National Nuclear Energy Agency (Indonesia)

2014-03-24

Synthesis and characterization of (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} absorbing material by mechanical alloying process has been performed. The absorbing material was prepared by oxide materials, namely BaCO{sub 3}, La{sub 2}O{sub 3}, TiO{sub 2}, Fe{sub 2}O{sub 3}, and MnCO{sub 3}. The mixture was milled for 10 h and then sintered at a temperature of 1000 ° C for 10 h. The refinement results of x-ray diffraction pattern of lanthanum manganite substituted with barium showed that the sample consisted of two phases, namely, La{sub 0.9125}MnO{sub 3} phase which has a structure monoclinic (I12/a1) with lattice parameters a = 5.527(1) Å, b = 5.572(1) Å and c = 7.810(1) Å, α = γ = 90° and β = 89.88(5)°, the unit cell volume of V = 240.57(8) Å{sup 3}, and the atomic density of ρ = 6.238 gr.cm{sup −3}. The microstructure analyses showed that the particle shapes was polygonal with the varied particle sizes of 1 ∼ 3 μm distributed homogeneously on the surface of the samples. The results of the electromagnetic wave absorption curve analysis by using a vector network analyzer (VNA) showed that the sample can absorb microwaves in the frequency range of 8-15 GHz with a very wide absorption bandwidth. It indicates that the as prepared absorber presents potential absorbing property in X and Ku-band. We concluded that the (Ba{sub 0.2}La{sub 0.8})Fe{sub 0.2}Mn{sub 0.4}Ti{sub 0.4}O{sub 3} material can be applied as a candidate absorber material of microwaves or electromagnetic wave.

Influence of ionic conductivity of the nano-particulate coating phase on oxygen surface exchange of La0.58Sr0.4Co0.2Fe0.8O3-δ

NARCIS (Netherlands)

Saher, S.; Naqash, S.; Boukamp, Bernard A.; Hu, Bobing; Xia, Changrong; Bouwmeester, Henricus J.M.

2017-01-01

The oxygen surface exchange kinetics of mixed-conducting perovskite La0.58Sr0.4Co0.2Fe0.8O3 d (LSCF) ceramics coated with a porous nano-particulate layer of either gadolinea (Gd2O3), ceria (CeO2) or 20 mol% Gd-doped ceria (GCO) was determined by electrical conductivity relaxation (ECR). The

40 CFR 600.111-08 - Test procedures.

Science.gov (United States)

2010-07-01

... § 600.109(b) while sampling the exhaust gas. (viii) Sampling must begin two seconds before beginning the... convenience of the user, the revised text is set forth as follows: § 600.111-08 Test procedures. (f) Special...

Electrocaloric effect and freezing temperature in (Pb0.8Ba0.2[(Zn1∕3Nb2∕30.7Ti0.3]O3 relaxor ferroelectric ceramic

Directory of Open Access Journals (Sweden)

A. Peláiz-Barranco

2016-09-01

Full Text Available The electrocaloric effect (ECE is studied in (Pb0.8Ba0.2[(Zn1∕3Nb2∕30.7Ti0.3]O3 relaxor ferroelectric ceramic by using an “indirect method”. The electric dependence for the polarization (hysteresis loops has been obtained for several temperatures showing typical relaxor characteristics. The temperature change ΔT, which is associated with the ECE, is calculated by using the temperature dependence for the polarization. A maximum value for ΔT is observed for temperatures close above the freezing temperature, showing an indirect evidence of that critical temperature. The results are discussed considering the contribution of the polar nanoregions to the polarization.

CO Sensing Properties of Nanostructured La0.8Sr0.2CoO3 Sensors Synthesized by EDTA-Glycol Method

Directory of Open Access Journals (Sweden)

G. N. Chaudhari

2008-11-01

Full Text Available We report a simple method for the preparation of pure LaCoO3 and La1-xSrxCoO3 (x = 0.1, 0.2 and 0.25 nanostructures by the EDTA-Glycol method. The final powders obtained by this method have been investigated by X-ray diffraction (XRD and scanning electron microscopy (SEM measurements. The gas sensitivity of pure and Sr doped LaCoO3 samples were investigated for CO, NH3, H2 and LPG. La0.8Sr0.2CoO3 powders (sample GIII calcined at 6500C, exhibited a good sensor response towards CO gas at 2500C. On impregnation of 1 wt.% Pd over sample GIII, the operation temperature reduced to 2000C with a significant rise in sensitivity. The response time also decreases from about 3.5 min for sample GIII to less than 2.5 min for the Pd loaded element. The electronic interaction between Pd and metal oxide semiconductor is proposed to account for the sensitization effect.

75 FR 5854 - Proposed Collection; Comment Request for NOT-141440-08

Science.gov (United States)

2010-02-04

...- 08, Production Tax Credit for Refined Coal. DATES: Written comments should be received on or before...: Production Tax Credit for Refined Coal. OMB Number: 1545-2158. Notice Number: NOT-141440-08. Abstract: This notice sets forth interim guidance pending the issuance of regulations relating to the tax credit under...

Operation Iraqi Freedom 06-08

Science.gov (United States)

2008-02-14

Managemen 15.6.6 Results Related t 15.6.7 NCOs and Multiple-Deployments 15.6.8 Validated Trainin 15.6.9 Theater Suicide Prevention Program and Suicide...include mental health providers who have deployed to the IT0 and are experienced using AHLTA- T . As noted above, as the operational theater matures in...Mental Health Advisory Team (MHAT) V Operation Iraqi Freedom 06-08 14 February 2008 Office of the Surgeon Multi-National Force-Iraq and Office

Dual functions of zirconium modification on improving the electrochemical performance of Ni-rich LiNi0.8Co0.1Mn0.1O2

Energy Technology Data Exchange (ETDEWEB)

Li, Xing; Zhang, Kangjia; Wang, Mingshan; Liu, Yang; Qu, Meizhen; Zhao, Wengao; Zheng, Jianming

2018-02-28

Trace amount of Zirconium (Zr) has been adopted to modify the crystal structure and surface of the Ni-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material. During cycling at 1.0C, the Zr-modified NCM811 shows an improved capacity retention of 92% after 100 cycles, higher than 75% for pristine NMC811. In addition, the Zr-modified NCM811 is capable of delivering a discharge capacity of 107 mAh g-1 at 10.0C rate, much higher than 28 mAh g-1 delivered by pristine material. These improved electrochemical performances are ascribed to the dual functions of Zr modification. On one hand, part of the Zr enters the crystal lattice, which is beneficial for reducing the Li/Ni cation mixing and enhancing the crystal stability of the cathode. On the other hand, the rest of the Zr forms a 1~2 nm thick coating layer on the surface of the NCM811 cathode, which effectively prevents the direct contact between NCM and the electrolyte, thus suppressing the detrimental interfacial reactions. Therefore, the Zr-modified LiNi0.8Co0.1Mn0.1O2 exhibited significantly enhanced cycling stability and charging/discharging rate capability in comparison with the untreated counterpart.

Charge disproportionation in (X0.6Sr0.4)0.99Fe0.8Co0.2O3-δ perovskites (X = La, Pr, Sm, Gd)

DEFF Research Database (Denmark)

Pedersen, Thomas; Saadi, Souheil; Nielsen, K.H.

2005-01-01

The change in crystal structure and the oxidation state in iron of iron-cobalt-based perovskites with different A-site cations is investigated by the use of powder XRD and Mossbauer spectroscopy. The perovskites investigated are (X0.6Sr0.4)(0.99)Fe0.8Co0.2O3-delta, where X is La, Pr, Sm or Gd...

Instrumentos de avaliação de leitura em adultos: um estudo psicométrico

Directory of Open Access Journals (Sweden)

Natália Martins Dias

Full Text Available RESUMO Objetivo: investigar as propriedades psicométricas de um teste de desempenho para avaliação de reconhecimento de palavras e de um checklist de autorrelato de dificuldades de leitura/indicadores de dislexia, em uma amostra de adultos. Métodos: foram avaliados 54 sujeitos, idades entre 18 e 57 anos (M=24,16; DP = 7,34, com Ensino Médio completo ou cursando a graduação. As avaliações foram realizadas utilizando o Teste Computadorizado de Competência de Leitura de Palavras para Adultos (TCLP-2 e o questionário de autorrelato Adult Dyslexia Checklist (ADC. Resultados: não foram observadas diferenças de desempenho em função da escolaridade e do gênero. O tempo de resposta foi menor no julgamento dos itens Corretos do TCLP-2 em relação aos itens incorretos (inversão, troca fonológica, erro ortográfico e pseudopalavra homófona. 18,5% dos participantes relataram dificuldades mais severas no ADC. Análise de grupos extremos mostrou que participantes com maiores pontuações/dificuldades no ADC tiveram pior desempenho nos itens Corretos do TCLP-2. Análise fatorial retornou solução com fator único para tipos de itens do TCLP-2. Dados de precisão se mostraram adequados para ambos os instrumentos, com valores de Spearman-Brown e alfa de Cronbach maiores que 0,70. Relações de baixa a moderadas foram observadas entre os dois instrumentos, provendo evidências de validade a ambos. Conclusão: o estudo apresentou dados psicométricos de dois instrumentos para avaliação de leitura em adultos. Ambos mostraram índices satisfatórios de precisão e evidências de validade por relação com outras variáveis. Frente à carência de instrumentos padronizados para avaliação de leitura em adultos no contexto nacional, o estudo estende sua contribuição à futura instrumentalização desta área.

Synthesis of capped nanosized Mn1-x Zn x Fe2O4 (0x0.8) by microwave refluxing for bio-medical applications

International Nuclear Information System (INIS)

Giri, Jyotsnendu; Sriharsha, Theerdhala; Asthana, Saket; Gundu Rao, Tumkur K.; Nigam, Arun K.; Bahadur, Dhirendra

2005-01-01

Substituted ferrites [Mn 1- x Zn x Fe 2 O 4 (0x0.8)] of nanoscale dimensions have been prepared by a novel microwave refluxing method. The effect of different parameters [such as pH, reflux time, presence of PEG (MW-3350) molecules] on particle morphology and size has been studied. Characterization of the above capped particles was done by XRD, FTIR, TEM and SQUID magnetometry. The as-prepared particles were further used for magnetoliposome preparation

Elastic wave velocities of iron-bearing Ringwoodite (Mg0.8Fe0.2)2SiO2 to 12GPa at room temperature

Science.gov (United States)

Higo, Y.; Li, B.; Inoue, T.; Irifune, T.; Libermann, R. C.

2002-12-01

At present, it is widely accepted that olivine is the most important mineral in the Earth's upper mantle. The elastic property changes associated with the phase transformations to its high-pressure polymorphs are very important parameters to constrain the composition of the mantle transition zone. In this study, we measured the elastic wave velocity of iron-bearing Ringwoodite (Mg0.8Fe0.2)2SiO4. The specimen was hot-pressed at 18GPa and 1273K in a 2000-ton Uniaxial Split Sphere Apparatus (ORANGE-2000: GRC at ehime university). The recovered polycrystalline specimen was characterized by x-ray diffraction, EPMA, ultrasonic techniques, and the density was determined by Archimedes' method, and found to be single-phase and fine-grained. Bench top measurements of the compressional and shear wave velocities yielded Vp=9.10 km/s and Vs=5.52 km/s. High-pressure ultrasonic measurement was carried out in a 1000-ton Uniaxial Split-Cylinder Apparatus (USCA-1000: SUNY) at pressures up to 12GPa at room temperature using ZnTe as internal pressure marker. The sample was surrounded by lead to minimize the deviatoric stress. Also in this experiment, the travel times of the Al2O3 buffer rod were used for pressure calculation. The travel times of the buffer rod under the same cell geometry have been calibrated as a function of sample pressure by the thermal equation of state of NaCl using in-situ X-ray diffraction techniques. The results of our high-pressure experiment, including the elastic moduli and their pressure dependence, effect of iron on the elastic moduli, as well as their implication for the mantle transition zone, will be presented.

Near-infrared and upconversion properties of neodymium-doped RE0.8La0.2VO4 (RE = Y, Gd) single-crystal fibres grown by the laser-heated pedestal growth technique

International Nuclear Information System (INIS)

Camargo, A S S de; Nunes, L A O; Andreeta, M R B; Hernandes, A C

2002-01-01

Neodymium-doped Y 0.8 La 0.2 VO 4 and Gd 0.8 La 0.2 VO 4 single-crystal fibres were successfully grown by the laser-heated pedestal growth (LHPG) technique. The fibres were completely transparent and no dark inclusions were observed by optical microscopy. In the characterization process, microprobe Raman, optical absorption, fluorescence, lifetime, and gain-excited state absorption spectra were investigated in addition to upconversion measurements. The fibres' structural and spectroscopic properties are very similar to those of YVO 4 and GdVO 4 bulk laser crystals, with the advantageous characteristic of broadened spectral linewidths that facilitate the pumping of the 1064 nm emission by a diode laser. These fairly new crystal compositions, that can be grown in fast and economical processes, are potential candidates for use as compact laser-active media

VLBI and GPS-based Time-Transfer Using CONT08 Data

Science.gov (United States)

Rieck, Carsten; Haas, Ruediger; Jaldehag, Kenneth; Jahansson, Jan

2010-01-01

One important prerequisite for geodetic Very Long Baseline Interferometry (VLBI) is the use of frequency standards with excellent short term stability. This makes VLBI stations, which are often co-located with Global Navigation Satellite System (GNSS) receiving stations, interesting for studies of time- and frequency-transfer techniques. We present an assessment of VLBI time-transfer based on the data of the two week long consecutive IVS CONT08 VLBI campaign by using GPS Carrier Phase (GPSCP). CONT08 was a 15 day long campaign in August 2008 that involved eleven VLBI stations on five continents. For CONT08 we estimated the worst case VLBI frequency link stability between the stations of Onsala and Wettzell to 1e-15 at one day. Comparisons with GPSCP confirm the VLBI results. We also identify time-transfer related challenges of the VLBI technique as used today.

THE EFFECT OF RARE EARTH ELEMENTS ON Cr PRECIPITATIONS IN A Cu-0.8WT%Cr ALLOY

Directory of Open Access Journals (Sweden)

Gewang Shuai

2011-05-01

Full Text Available The microstructural evolution of Cu-based alloys during aging was studied using a quantitative metallographic method. Samples were cut from ingots of Cu-0.8wt%Cr and Cu-0.8wt%Cr-RE alloys. These were solution treated at 1000 ºC for 1.5h and subsequently quenched in water, then separately aged at 480 ºC for different durations. The microstructures were observed by optical microscope, and the characteristic geometric parameters of precipitated Cr phase, including volume fraction VV, face density NA, mean diameter and roundness, were measured. These data provided more details about the process of aging. The results showed that precipitation of Cr phase occurred in the form of particles during aging. Rare earth elements promoted the precipitation of Cr phase and dispersed Cr particles. The phenomenon of overaging came earlier in Cu-Cr-RE than in Cu-Cr. In the present work, the optimal aging time at 480 ºC was 2 hrs for the Cu-0.8wt%Cr-RE alloy and 3 hours for the Cu-0.8wt%Cr alloy.

40 CFR 86.1817-08 - Complete heavy-duty vehicle averaging, trading, and banking program.

Science.gov (United States)

2010-07-01

..., trading, and banking program. 86.1817-08 Section 86.1817-08 Protection of Environment ENVIRONMENTAL... Complete heavy-duty vehicle averaging, trading, and banking program. Section 86.1817-08 includes text that.... (1) Manufacturers of Otto-cycle vehicles may participate in an NMHC averaging, banking and trading...

Molten salt synthesis of La0.8Sr0.2MnO3 powders for SOFC cathode electrode

Science.gov (United States)

Gu, Sin-il; Shin, Hyo-soon; Hong, Youn-woo; Yeo, Dong-hun; Kim, Jong-hee; Nahm, Sahn; Yoon, Sang-ok

2012-08-01

For La0.8Sr0.2MnO3 (LSM) perovskite, used as the cathode material for solid oxide fuel cells (SOFC), it is known that the formation of a triple-phase-boundary is restrained due to the formation of a second phase at the YSZ/electrode interface at high temperature. To decrease the 2nd phase, lowering the sintering temperature has been used. LSM powder was synthesized by molten salt synthesis method to control its particle size, shape, and agglomeration. We have characterized the phase formation, particle size, shape, and sintering behavior of LSM in the synthesis using the variation of KCl, LiCl, KF and its mixed salts as raw materials. In the case of KCl and KCl-KF salts, the particle size and shape of the LSM was well controlled and synthesized. However, in the case of LiCl and KCl-LiCl salts, LiMnOx as 2nd phase and LSM were synthesized simultaneously. In the case of the mixed salt of KCl-KF, the growth mechanism of the LSM particle was changed from `diffusion-controlled' to `reaction-controlled' according to the amount of mixed salt. The sintering temperature can be decreased below 1000 °C by using the synthesized LSM powder.

Electrical and structural properties of La0.8Sr0.2Mn0.5Co0.5O3±δ films produced by pulsed laser deposition

DEFF Research Database (Denmark)

Pryds, Nini; Christensen, Bo Toftmann; Schou, Jørgen

2005-01-01

La0.8Sr0.2Mn0.5Co0.5O3 (LSMCO) films for the use as contact layers or protective coatings in solid oxide fuel cells (SOFC) have been deposited on glass substrates by pulsed laser deposition (PLD). PLD is an obvious technique for thin film production of complex oxides, because of the ability...

NCBI nr-aa BLAST: CBRC-DSIM-08-0021 [SEVENS

Lifescience Database Archive (English)

Full Text Available CBRC-DSIM-08-0021 ref|NP_572183.1| CG6986-PA, isoform A [Drosophila melanogaster] r...ef|NP_726950.1| CG6986-PB, isoform B [Drosophila melanogaster] ref|NP_001014723.1| CG6986-PD, isoform D [Drosophila mela...nogaster] ref|NP_001014724.1| CG6986-PC, isoform C [Drosophila melanogaster] gb|AAM75074.1| RE56254p [Drosophila mela...nogaster] gb|AAF45980.2| CG6986-PA, isoform A [Drosophila mela...nogaster] gb|AAN09130.1| CG6986-PB, isoform B [Drosophila melanogaster] gb|AAX52477.1| CG6986-PC, isoform C [Drosophila mela

Energy dispersions of single-crystalline Bi2.0Sr1.8Ca0.8La0.3Cu2.1O8+δ superconductors determined using angle-resolved photoelectron spectroscopy

International Nuclear Information System (INIS)

Lindberg, P.A.P.; Shen, Z.; Dessau, D.S.; Wells, B.O.; Mitzi, D.B.; Lindau, I.; Spicer, W.E.; Kapitulnik, A.

1989-01-01

Angle-resolved photoemission studies of single-crystalline La-doped Bi-Sr-Ca-Cu- 90-K superconductors (Bi 2.0 Sr 1.8 Ca 0.8 La 0.3 Cu 2.1 O 8+δ ) were performed utilizing synchrotron radiation covering the photon energy range 10--40 eV. The data conclusively reveal a dispersionless character of the valence-band states as a function of the wave-vector component parallel to the c axis, in agreement with the predictions of band calculations. Band effects are evident from both intensity modulations of the spectral features in the valence band and from energy dispersions as a function of the wave vector component lying in the basal a-b plane

Aging phenomena in Cu{sub 0.1}Ni{sub 0.8}Co{sub 0.2}Mn{sub 1.9}O{sub 4} NTC ceramics

Energy Technology Data Exchange (ETDEWEB)

Shpotyuk, O.; Vakiv, M.; Mrooz, O. [Scientific Research Co. ' ' Carat' ' , Lviv (Ukraine); Hadzaman, I. [Scientific Research Co. ' ' Carat' ' , Lviv (Ukraine); Drohobych State Pedagogical Univ., Drohobych (Ukraine); Plewa, J.; Uphoff, H.; Altenburg, H. [Fachhochschule Muenster, Steinfurt (Germany)

2002-07-01

Aging effects in Cu{sub 0.1}Ni{sub 0.8}Co{sub 0.2}Mn{sub 1.9}O{sub 4} NTC ceramics were studied for the first time by electrical and microstructural measurements. The increase in resistivity induced by aging tests at 125 and 170 C during 1000 h was observed. The changes of the electrical properties of the investigated NTC thermistors were explained, using the results of ceramics microstructural characterization, thermogravimetry, optical and electron microscopy techniques. (orig.)

La(0.4)Ba(0.6)Fe(0.8)Zn(0.2)O(3-delta) as cathode in solid oxide fuel cells for simultaneous NO reduction and electricity generation.

Science.gov (United States)

Zhou, Renjie; Bu, Yunfei; Xu, Dandan; Zhong, Qin

2014-01-01

A perovskite-type oxide La(0.4)Ba(0.6)Fe(0.8)Zn(0.2)O(3-delta) (LBFZ) was investigated as the cathode material for simultaneous NO reduction and electricity generation in solid oxide fuel cells (SOFCs). The microstructure of LBFZ was demonstrated by X-ray diffraction and scanning electron microscopy. The results showed that a single cubic perovskite LBFZ was formed after calcined at 1100 degrees C. Meanwhile, the solid-state reaction between LBFZ and Ce(0.8)Sm(0.2)O(1.9) (SDC) at 900 degrees C was negligible. To measure the electrochemical properties, SOFC units were constructed with Sm(0.9)Sr(0.1)Cr(0.5)Fe(0.5)O3 as the anode, SDC as the electrolyte and LBFZ as the cathode. The maximum power density increased with the increasing NO concentration and temperature. The cell resistance is mainly due to the cathodic polarization resistance.

Project SFR 1 SAR-08. Update of priority of FEPs from Project SAFE

International Nuclear Information System (INIS)

Gordon, Anna; Loefgren, Martin; Lindgren, Maria

2008-03-01

SFR 1 is a repository for final disposal of low and intermediate level radioactive waste produced at Swedish nuclear power plants, as well as at Swedish industrial, research, and medical treatment facilities. The repository obtained operational license in March 1988. The aim of Project SFR 1 SAR-08 is to perform an updated safety analysis, according to requirements in the regulations. A major difference between this and previous safety analyses is that repository safety should be demonstrated for 100,000 years after repository closure. This should be compared with the time frame of the safety assessment in Project SAFE that was 10,000 years. Due to the extended time frame, permafrost and glaciation have to be considered in the reference evolution of Project SFR 1 SAR-08. Other rationales for the update are recent input from the authorities concerning SAFE documents and the SFR 1 repository, as well as new data concerning the SFR 1 inventory. This report describes the outcome of revisiting the qualitative FEP (Features, Events and Processes) analysis carried out within Project SAFE for the SFR 1 repository. Each and every interaction definition, as defined in SAFE, has been examined with the aim at assuring that the SAFE interaction matrices are also applicable for SAR-08. It was found that this is generally the case, but seven new interactions were defined in order to make the interaction matrices more applicable for SAR-08. The priority of all interactions assigned priority 1 and many interactions assigned priority 2 in SAFE have been carefully examined. The examination has been made in the context of the general initial and boundary conditions that should also form the basis for the SAR-08 main scenario and less probable scenarios. In 48 cases, the priority of the interaction needed upgrading, compared to in SAFE. In a majority of these cases, the upgrade is due to the extended time frame of the safety assessment, from 10,000 years in SAFE to 100,000 years in SAR

Project SFR 1 SAR-08. Update of priority of FEPs from Project SAFE

Energy Technology Data Exchange (ETDEWEB)

Gordon, Anna (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE)); Loefgren, Martin; Lindgren, Maria (Kemakta Konsult AB, Stockholm (SE)) (eds.)

2008-03-15

SFR 1 is a repository for final disposal of low and intermediate level radioactive waste produced at Swedish nuclear power plants, as well as at Swedish industrial, research, and medical treatment facilities. The repository obtained operational license in March 1988. The aim of Project SFR 1 SAR-08 is to perform an updated safety analysis, according to requirements in the regulations. A major difference between this and previous safety analyses is that repository safety should be demonstrated for 100,000 years after repository closure. This should be compared with the time frame of the safety assessment in Project SAFE that was 10,000 years. Due to the extended time frame, permafrost and glaciation have to be considered in the reference evolution of Project SFR 1 SAR-08. Other rationales for the update are recent input from the authorities concerning SAFE documents and the SFR 1 repository, as well as new data concerning the SFR 1 inventory. This report describes the outcome of revisiting the qualitative FEP (Features, Events and Processes) analysis carried out within Project SAFE for the SFR 1 repository. Each and every interaction definition, as defined in SAFE, has been examined with the aim at assuring that the SAFE interaction matrices are also applicable for SAR-08. It was found that this is generally the case, but seven new interactions were defined in order to make the interaction matrices more applicable for SAR-08. The priority of all interactions assigned priority 1 and many interactions assigned priority 2 in SAFE have been carefully examined. The examination has been made in the context of the general initial and boundary conditions that should also form the basis for the SAR-08 main scenario and less probable scenarios. In 48 cases, the priority of the interaction needed upgrading, compared to in SAFE. In a majority of these cases, the upgrade is due to the extended time frame of the safety assessment, from 10,000 years in SAFE to 100,000 years in SAR

Project SFR 1 SAR-08. Update of priority of FEPs from Project SAFE

Energy Technology Data Exchange (ETDEWEB)

Gordon, Anna [Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE); Loefgren, Martin; Lindgren, Maria [Kemakta Konsult AB, Stockholm (SE); eds.

2008-03-15

SFR 1 is a repository for final disposal of low and intermediate level radioactive waste produced at Swedish nuclear power plants, as well as at Swedish industrial, research, and medical treatment facilities. The repository obtained operational license in March 1988. The aim of Project SFR 1 SAR-08 is to perform an updated safety analysis, according to requirements in the regulations. A major difference between this and previous safety analyses is that repository safety should be demonstrated for 100,000 years after repository closure. This should be compared with the time frame of the safety assessment in Project SAFE that was 10,000 years. Due to the extended time frame, permafrost and glaciation have to be considered in the reference evolution of Project SFR 1 SAR-08. Other rationales for the update are recent input from the authorities concerning SAFE documents and the SFR 1 repository, as well as new data concerning the SFR 1 inventory. This report describes the outcome of revisiting the qualitative FEP (Features, Events and Processes) analysis carried out within Project SAFE for the SFR 1 repository. Each and every interaction definition, as defined in SAFE, has been examined with the aim at assuring that the SAFE interaction matrices are also applicable for SAR-08. It was found that this is generally the case, but seven new interactions were defined in order to make the interaction matrices more applicable for SAR-08. The priority of all interactions assigned priority 1 and many interactions assigned priority 2 in SAFE have been carefully examined. The examination has been made in the context of the general initial and boundary conditions that should also form the basis for the SAR-08 main scenario and less probable scenarios. In 48 cases, the priority of the interaction needed upgrading, compared to in SAFE. In a majority of these cases, the upgrade is due to the extended time frame of the safety assessment, from 10,000 years in SAFE to 100,000 years in SAR

A study of (Ba0.5Sr0.5)1-xSm xCo0.8Fe0.2O3-δ as a cathode material for IT-SOFCs

International Nuclear Information System (INIS)

Li Shuyan; Lue Zhe; Wei Bo; Huang Xiqiang; Miao Jipeng; Cao Gang; Zhu Ruibin; Su Wenhui

2006-01-01

(Ba 0.5 Sr 0.5 ) 1-x Sm x Co 0.8 Fe 0.2 O 3-δ (BSSCF; x = 0.05-0.15) compounds were synthesized with EDTA-Pechini method and characterized by powder X-ray diffraction (XRD), electrical conductivity and thermal expansion coefficient (TEC) measurements, as well as the electrochemical impedance spectra measurement. According to the XRD results, the main phase of the material belongs to the cubic perovskite-type, and the lattice contracting with the increasing contents of Sm 3+ . The TEC of the compounds is 19.1-20.3 x 10 -6 K -1 from 30 to 800 deg. C, which close to the values of Co-based materials, such as Ba 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3-δ (BSCF). And the conductivity of BSSCF is higher than that of BSCF; e.g., about 212% higher at 500 deg. C for the x = 0.15 compound. Electrochemical impedance spectra at intermediate temperature revealed the better electrochemical performance of BSSCF than BSCF; e.g., the total resistance values of BSSCF electrode is 2.98 Ω cm 2 at 500 deg. C, nearly 50% lower than that of BSCF

Size-dependent photocatalytic activity of La0.8Sr0.2MnO3 nanoparticles prepared by hydrothermal synthesis

Science.gov (United States)

Rahmani Afje, F.; Ehsani, M. H.

2018-04-01

Synthesize of La0.8Sr0.2MnO3 (LSMO) manganite were carried out in different particle sizes by hydrothermal method. Structural and optical properties of the prepared specimens were studied by x-ray diffraction (XRD), Fourier transform infra-red (FT-IR) spectroscopy, field emission scanning electron microscopy (FESEM), and UV–vis spectroscopy. The XRD study, coupled with the Rietveld refinement, exhibited rhombohedral structure with R-3C space group. Using the FT-IR and FESEM analyses, the perovskite structure of the samples with Nano-rod-like morphologies were inferred. Furthermore, the average sizes of 48.11, 70.99 and 111.45 nm were obtained for the ones sintered at 800, 900, and 1000 °C temperatures, respectively. The optical research showed that band gap energy is about 2.13 eV, being suitable in visible-light photocatalytic activity for water purification from dyes and toxic organic materials. The photo-degradation efficiency for decolorizing methyl orange solution (10 ppm) for various samples (100 ppm) were systematically probed and a strong relation is concluded between particle size and photocatalytic activity.

Ferroelectric properties of BaTiO3/PbZr0.2Ti.08O3 bilayer thin film

Science.gov (United States)

Salev, Pavel; Yang, Chun; Grigoriev, Alexei

2014-03-01

The thin film ferroelectric BaTiO3/PbZr0.2Ti0.8O3 bilayer was epitaxially grown on SrRuO3/SrTiO3 substrate by RF sputtering. Electrical measurements of polarization switching revealed two different switching regimes - a small ferroelectric hysteresis loop at low applied voltage and a larger loop at a high voltage. The measured dielectric permittivity corresponds to weak electrostatic coupling between two layers according to Landau-Ginsburg-Devonshire theory. This weak coupling may allow for independent polarization states to exist in individual layers. This can lead to stable head-to-head and tail-to-tail polarization domain configurations, which would explain the two switching regimes observed in electrical measurements. The compensation of polarization gradient across the interface can be explained by the enhancement of interface charge carrier density due to strong bending of electron energy bands. This work was supported by NSF award DMR-1057159.

The atomic structure of protons and hydrides in Sm1.92Ca0.08Sn2O7-δ pyrochlore from DFT calculations and FTIR spectroscopy

DEFF Research Database (Denmark)

Bork, Nicolai Christian; Eurenius, K. E. J.; Rossmeisl, Jan

2012-01-01

A combined density functional theory and Fourier transform infrared spectroscopy study of the structure and specific site preference of protons and hydrides in the pyrochlore Sm1.92Ca0.08Sn2O7-δ is presented. Two protonic sites of particular high stability are identified, both located on O(1......) oxygen atoms closely associated with a Ca dopant. Further, the unexpected presence of Ho hydride defects in undoped, oxygen deficient Sm2Sn2O7 is reported. Finally, the stretching frequencies and relative intensities for these and other sites are calculated. The main features of the Fourier transform...

Chemically stable perovskites as cathode materials for solid oxide fuel cells: La-doped Ba0.5Sr0.5Co0.8Fe0.2O(3-δ).

Science.gov (United States)

Kim, Junyoung; Choi, Sihyuk; Jun, Areum; Jeong, Hu Young; Shin, Jeeyoung; Kim, Guntae

2014-06-01

Ba0.5Sr0.5Co0.8Fe0.2O(3-δ) (BSCF) has won tremendous attention as a cathode material for intermediate-temperature solid-oxide fuel cells (IT-SOFC) on the basis of its fast oxygen-ion transport properties. Nevertheless, wide application of BSCF is impeded by its phase instabilities at intermediate temperature. Here we report on a chemically stable SOFC cathode material, La0.5Ba0.25Sr0.25Co0.8Fe0.2O(3-δ) (LBSCF), prepared by strategic approaches using the Goldschmidt tolerance factor. The tolerance factors of LBSCF and BSCF indicate that the structure of the former has a smaller deformation of cubic symmetry than that of the latter. The electrical property and electrochemical performance of LBSCF are improved compared with those of BSCF. LBSCF also shows excellent chemical stability under air, a CO2-containg atmosphere, and low oxygen partial pressure while BSCF decomposed under the same conditions. Together with this excellent stability, LBSCF shows a power density of 0.81 W cm(-2) after 100 h, whereas 25 % degradation for BSCF is observed after 100 h. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Nanoblast synthesis and consolidation of (La0.8Sr0.2)(Ga0.9Mg0.1)O(3-delta) under Spark plasma sintering conditions.

Science.gov (United States)

Vasylkiv, Oleg; Borodianska, Hanna; Badica, Petre; Zhen, Yongda; Tok, Alfred

2009-01-01

Four-cation nanograined strontium and magnesium doped lanthanum gallate (La0.8Sr0.2) (Ga0.9Mg0.1)O(3-delta) (LSGM) and its composite with 2 wt% of ceria (LSGM-Ce) were prepared. Morphologically homogeneous nanoreactors, i.e., complex intermediate metastable aggregates of desired composition were assembled by spray atomization technique, and subsequently loaded with nanoparticles of highly energetic C3H6N6O6. Rapid nanoblast calcination technique was applied and the final composition was synthesized within the preliminary localized volumes of each single nanoreactor on the first step of spark plasma treatment. Subsequent SPS consolidations of nanostructured extremely active LSGM and LSGM-Ce powders were achieved by rapid treatment under pressures of 90-110 MPa. This technique provided the heredity of the final structure of nanosize multimetal oxide, allowed the prevention of the uncontrolled agglomeration during multicomponent aggregates assembling, subsequent nanoblast calcination, and final ultra-rapid low-temperature SPS consolidation of nanostructured ceramics. LaSrGaMgCeO(3-delta) nanocrystalline powder consisting of approximately 11 nm crystallites was consolidated to LSGM-Ce nanoceramic with average grain size of approximately 14 nm by low-temperature SPS at 1250 degrees C. Our preliminary results indicate that nanostructured samples of (La0.8Sr0.2)(Ga0.9Mg0.1)O(3-delta) with 2 wt% of ceria composed of approximataley 14 nm grains can exhibit giant magnetoresistive effect in contrast to the usual paramagnetic properties measured on the samples with larger grain size.

ThPt{sub 3+x}Be (x = 0.08): crystal structure and physical properties

Energy Technology Data Exchange (ETDEWEB)

Gumeniuk, Roman [Institut fuer Experimentelle Physik, TU Bergakademie Freiberg (Germany); Max-Planck-Institut fuer Chemische Physik fester Stoffe, Dresden (Germany); Kohout, Miroslav; Schnelle, Walter; Burkhardt, Ulrich; Leithe-Jasper, Andreas [Max-Planck-Institut fuer Chemische Physik fester Stoffe, Dresden (Germany); Zschornak, Matthias [Institut fuer Experimentelle Physik, TU Bergakademie Freiberg (Germany)

2017-01-03

ThPt{sub 3+x}Be (x = 0.08) is synthesized by arc melting of a mixture of the elements. It crystallizes with its own type of structure [space group I4/mmm (No. 139), a = 7.7370(4), c = 11.4990(6) Aa], which can be related to the cubic Ru{sub 3}Sn{sub 7} and W{sub 2}Cr{sub 21}C{sub 6} types. Measurements of magnetic susceptibility, electrical resistivity and specific heat indicate ThPt{sub 3+x}Be (x = 0.08) to be a diamagnet [χ{sub 0} = -9.0(3) x 10{sup -6} emu mol{sup -1}] with metallic electrical resistivity, in good agreement with the calculated electronic structure [N(E{sub F}) = 3.2 states eV{sup -1} f.u.{sup -1}]. A chemical bonding analysis was performed by the QTAIM and ELI-D approaches. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Characterization of the yttria-stabilized zirconia thin film electrophoretic deposited on La0.8Sr0.2MnO3 substrate

International Nuclear Information System (INIS)

Yang, Koho; Shen, Jung-Hsiung; Yang, Kai-Yun; Hung, I-Ming; Fung, Kuan-Zong; Wang, Moo-Chin

2007-01-01

The yttria-stabilized zirconia (YSZ) thin films electrophoretic deposited on the La 0.8 Sr 0.2 MnO 3 (LSM) substrate have been characterized by using zeta potential analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The La 2 Zr 2 O 7 (LZ) formed at the interface between the YSZ thin film and LSM substrate, after sintered at 1400 o C for 52 h, are identified by XRD. The zeta potential of the YSZ particles in pure ethanol-acetone is about 7.8 mV, but when the I 2 concentration is greater than 0.6 g/1, the zeta potential attains a constant value, 46 mV. The relation between deposit weight of the YSZ films and the applied voltage shows a non-linear behavior. Thickness of the YSZ thin film deposited on the LSM substrate by electrophoretic deposition is controlled by a diffusion process. A larger LZ with the thickness of 200 nm is formed at the interface between the YSZ film and the LSM substrate

Synthesis of capped nanosized Mn 1-xZn xFe 2O 4 (0⩽ x⩽0.8) by microwave refluxing for bio-medical applications

Science.gov (United States)

Giri, Jyotsnendu; Sriharsha, Theerdhala; Asthana, Saket; Gundu Rao, Tumkur K.; Nigam, Arun K.; Bahadur, Dhirendra

2005-05-01

Substituted ferrites [Mn 1-xZn xFe 2O 4 (0⩽ x⩽0.8)] of nanoscale dimensions have been prepared by a novel microwave refluxing method. The effect of different parameters [such as pH, reflux time, presence of PEG (MW-3350) molecules] on particle morphology and size has been studied. Characterization of the above capped particles was done by XRD, FTIR, TEM and SQUID magnetometry. The as-prepared particles were further used for magnetoliposome preparation.

A novel bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector for anode-supported tubular solid oxide fuel cell via slurry-brushing and co-sintering process

Energy Technology Data Exchange (ETDEWEB)

Xu, Yanjie; Wang, Shaorong; Liu, Renzhu; Wen, Tinglian; Wen, Zhaoyin [CAS Key Laboratory of Materials for Energy Conversion, Shanghai Institute of Ceramics, Chinese Academy of Sciences (SICCAS), 1295 Dingxi Road, Shanghai 200050 (China)

2011-02-01

Considering that conventional lanthanum chromate (LaCrO{sub 3}) interconnector is hard to be co-sintered with green anode, we have fabricated a novel bilayered interconnector which consists of La-doped SrTiO{sub 3} (Sr{sub 0.6}La{sub 0.4}TiO{sub 3}) and Sr-doped lanthanum manganite (La{sub 0.8}Sr{sub 0.2}MnO{sub 3}). Sr{sub 0.6}La{sub 0.4}TiO{sub 3} is conductive and stable in reducing atmosphere, locating on the anode side; while La{sub 0.8}Sr{sub 0.2}MnO{sub 3} is on the cathode side. A slurry-brushing and co-sintering method is applied: the Sr{sub 0.6}La{sub 0.4}TiO{sub 3} and La{sub 0.8}Sr{sub 0.2}MnO{sub 3} slurries are successively brushed onto green anode specimen, followed by co-firing course to form a dense bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector. For operating with humidified hydrogen and oxygen at 900 C, the ohmic resistances between anode and cathode/interconnector are 0.33 {omega} cm{sup 2} and 0.186 {omega} cm{sup 2}, respectively. The maximum power density is 290 mW cm{sup -2} for a cell with interconnector, and 420 mW cm{sup -2} for a cell without it, which demonstrates that nearly 70% of the power output can be achieved using this bilayered Sr{sub 0.6}La{sub 0.4}TiO{sub 3}/La{sub 0.8}Sr{sub 0.2}MnO{sub 3} interconnector. (author)

Sample (S): SE57_S08 [Metabolonote[Archive

Lifescience Database Archive (English)

Full Text Available SE57_S08 Lotus japonicus (accessions B129 gifu and MG20 miyakojima) Lotus japonicus... NCBI taxonomy:34305 Lotus japonicus accessions were a gift from Dr. Toshio Aoki (Nihon University, Japan). ...

Temperature dependent optical dispersion and electronic transitions of highly a-axis oriented 0.8Pb(Zn{sub 1/3}Nb{sub 2/3})O{sub 3}-0.2PbTiO{sub 3} films on SrTiO{sub 3} crystals: An ellipsometric evidence

Energy Technology Data Exchange (ETDEWEB)

Li, C.Q.; Zhang, J.Z.; Xu, L.P.; Zhu, J.J.; Duan, Z.H.; Hu, Z.G., E-mail: zghu@ee.ecnu.edu.cn; Chu, J.H.

2016-03-31

The relaxor ferroelectric 0.8Pb(Zn{sub 1/3}Nb{sub 2/3})O{sub 3}-0.2PbTiO{sub 3} (0.8PZN-0.2PT) films have been fabricated on (100) SrTiO{sub 3} substrates by the sol–gel method. The structure, optical properties and electronic transitions have been investigated using X-ray diffraction (XRD), atomic force microscopy, scanning electron microscopy and ellipsometric spectra. The pure perovskite phase with highly a-axis (100)-preferential orientation as well as low screw dislocation are extracted based on high resolution XRD. Moreover, the red-shift trend of the electronic transitions at about 3.01 eV as a function of temperature follows the Bose-Einstein law induced by the electron–phonon interactions and lattice thermal expansion. Interestingly, the different optical behavior and structure variation can be observed at about 500 K, which reveal tetragonal to cubic structural transformations for the 0.8PZN-0.2PT films. It indicates that the potential application of ellipsometric spectra in judging the phase transitions and symmetries of ferroelectric material. - Highlights: • The highly a-axis oriented as well as low screw dislocated films were fabricated. • The temperature-dependent evolution of band gap was investigated. • The tetragonal to cubic structural transformations were observed at about 500 K. • The electronic transition mechanism was discussed mainly by first-principles calculations.

High performance protonic ceramic membrane fuel cells (PCMFCs) with Ba{sub 0.5}Sr{sub 0.5}Zn{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} perovskite cathode

Energy Technology Data Exchange (ETDEWEB)

Ding, Hanping; Lin, Bin; Liu, Xingqin; Meng, Guangyao [Department of Materials Science and Engineering, University of Science and Technology of China (USTC), No. 96 Jinzhai Road, Hefei 230026 (China)

2008-09-15

Protonic ceramic membrane fuel cells (PCMFCs) based on proton-conducting electrolytes have attracted much attention because of many advantages, such as low activation energy and high energy efficiency. BaZr{sub 0.1}Ce{sub 0.7}Y{sub 0.2}O{sub 3-{delta}} (BZCY7) electrolyte based PCMFCs with stable Ba{sub 0.5}Sr{sub 0.5}Zn{sub 0.2}Fe{sub 0.8}O{sub 3-{delta}} (BSZF) perovskite cathode were investigated. Using thin membrane BZCY7 electrolyte (about 15 {mu}m in thickness) synthesized by a modified Pechini method on NiO-BZCY7 anode support, PCMFCs were assembled and tested by selecting stable BSZF perovskite cathode. An open-circuit potential of 1.015 V, a maximum power density of 486 mW cm{sup -2}, and a low polarization resistance of the electrodes of 0.08 {omega} cm{sup 2} was achieved at 700 C. The results have indicated that BZCY7 proton-conducting electrolyte with BSZF cathode is a promising material system for the next generation solid oxide fuel cells. (author)

Microwave melt and offgas analysis results from a Ferro Corporation reg-sign glass frit