Energy Technology Data Exchange (ETDEWEB)

Anomalous features in Gulf Coast Salt domes exhibit deviations from normally pure salt and vary widely in form from one dome to the next, ranging considerably in length and width. They have affected both conventional and solution mining in several ways. Gas outbursts, insolubles, and potash (especially carnallite) have led to the breakage of tubing in a number of caverns, and caused irregular shapes of many caverns through preferential leaching. Such anomalous features essentially have limited the lateral extent of conventional mining at several salt mines, and led to accidents and even the closing of several other mines. Such anomalous features, are often aligned in anomalous zones, and appear to be related to diapiric processes of salt dome development. Evidence indicates that anomalous zones are found between salt spines, where the differential ...

Energy Technology Data Exchange (ETDEWEB)

Completion of the Phase III evaluation and comparison of salt disposition alternatives was supported with enhanced computer models and analysis for each case on the ''short list'' of four options. SPEEDUP(TM) models and special purpose models describing mass and energy balances and flow rates were developed and used to predict performance and production characteristics for each of the options. Results from the computational analysis were a key part of the input used to select a primary and an alternate salt disposition alternative.

Energy Technology Data Exchange (ETDEWEB)

This research investigated the inhibiting effects that sodium salts of linear monocarboxylic acids displayed towards the corrosion process of AZ31 Mg alloy in ASTM D 1387 saline solution (a synthetic industrial cooling water). The length of the aliphatic chain of the acids ranged between 7 and 15 carbon atoms. The inhibiting action of these salts can be related to the precipitation of an insoluble magnesium salt, which mainly affected the anodic reaction. The aliphatic chain length controlled the anion solubility and the reaction rate of magnesium carboxylate formation. For all the salts, an optimum concentration was experienced: 10{sup -2} M for sodium decanoate (caprate), 10{sup -3} M for sodium dodecanoate (laurate), 10{sup -4} M for sodium tetradecanoate (myristate); when this concentration was exceeded, a diminution (even a disappearance) in the inhibiting action was found. ...

International Nuclear Information System (INIS)

The static thermophysical properties of the molten salt system like LiF-NaF-BeF_2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 0.15LiF-0.58NaF-0.27BeF_2, over the temperature range from 873.15K to 1073.15K at one atmosphere pressure, is described by using modified Peng-Robinson equation. The density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermophysical properties such as the enthalpy, entropy and heat capacity at constant pressure are evaluated by the fugacity coefficient and residual function methods respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity ...

Science.gov (United States)

The static thermophysical properties of the molten salt system like LiF-NaF-BeF2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 0.15LiF-0.58NaF-0.27BeF2, over the temperature range from 873.15K to 1073.15K at one atmosphere pressure, is described by using modified Peng-Robinson equation. The density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermophysical properties such as the enthalpy, entropy and heat capacity at constant pressure are evaluated by the fugacity coefficient and residual function methods respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity evaluated ...

UK PubMed Central (United Kingdom)

Norepinephrine stimulates the growth of a range of bacterial species in nutritionally poor SAPI minimal salts medium containing 30% serum. Addition of size-fractionated serum components to SAPI...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Mixtures of organic-inorganic substances are studied for their performance as energy storage media. Use is made of the fact that organic substances give higher amounts of energy but within a wide range of temperature on the one side and the fact that inorganic substances give lower amounts of energy at constant temperature on the other side. Mixtures of both types of substances, in different ratios, are investigated for the object of determining that optimum composition which stores a higher amount of energy and, meanwhile, releases it at a constant temperature or within a narrow range of temperature. The mixtures used are composed of Glauber`s salt (Na{sub 2}SO{sub 4}.10H{sub 2}O) and stearic acid in different proportions. The effect of cooling fluid flow rate and ambient temperature as well as the effect of addition of a nucleating agent is studied. The results showed that the highest amount of energy stored could be ...

DEFF Research Database (Denmark)

The syntheses of N-alkylated deoxynojirimycin and 1,5-dideoxy-1,5-iminoxylitol derivatives having either a D- or an L-erythritol-3-sulfate functionalized N-substituent are reported. The alkylating agent used was a cyclic sulfate derivative, whereby selective attack of the nitrogen atom at the least hindered primary center afforded the desired ammonium salt. In aqueous solution, these salts were configurationally labile at the ammonium center. Sulfonium and/or selenonium analogues of the ammonium salts were prepared by analogous reactions. The chalcogen salts were obtained as mixtures of diastereomers, separable in some cases, differing only in the stereochemistry at the configurationally stable sulfur or selenium atoms. Proof of configuration and conformation of each compound was obtained by detailed NMR experiments. The compounds are six-membered ring analogues of salacinol, a ...

British Library Electronic Table of Contents (United Kingdom)

Soils of arid regions of Central Asia contain salts of different types that may differentially affect seed germination and plant development. We studied effect of NaCl, Na2SO4, 2NaCl + KCl + CaCl2 and 2Na2SO4+K2SO4+MgSO4 on germination of Kochia prostrata and Kochia scoparia seeds under a range of concentrations from 0.5 to 5% and at two constant temperature regimes +22 degrees C and +6 degrees C. The observed salt tolerance limit of germination at constant temperature +22 degrees C for both species was 5-6%, while at low temperature (+6 degrees C) this limit was 2%. The salt tolerance of young plants (before flowering) was 3% for NaCl. Low concentrations of sulfuric and mixed salts had a stimulating effect on seed germination in K. prostrata. Despite similarity of salt-tolerance limits...

International Nuclear Information System (INIS)

The precipitation reaction of some rare earth chlorides (La/Ce/Nd/GdCl3) in a LiCl-KCl molten salt has been carried out by using the oxygen sparging method. In this study, regardless of the oxygen sparging time and the molten salt temperature, oxychlorides (REOCl) for LaCl3, NdCl3 and GdCl3, and an oxide (REO2) for CeCl3 are formed as a precipitate. The conversion of rare-earth chlorides into insoluble precipitates was described by using a conversion ratio. The conversion ratio increased exponentially with the oxygen sparging time and finally showed asymptotic value at 1,023K of the molten salt temperature condition. The conversion ratios of LaCl3, NdCl3 and GdCl3 were increased with the molten salt temperature, however, even though the conversion ratio was increased from 0.660 to 0.995 with increasing molten salt temperature from 823 to 923 K at 60 min of a sparging time, the ...

Energy Technology Data Exchange (ETDEWEB)

The solubilities of plutonium and uranium have been determined for alkaline salt solutions having compositions which bound those which will be processed in the In-Tank Precipitation (ITP) process. Loadings of plutonium and uranium onto monosodium titanate (MST) have been determined at temperatures bounding those expected to occur during ITP and using a salt solution which was determined to have the maximum solubility for uranium and plutonium. Fissile loadings increase with decreasing amounts of MST in contact with the salt solutions saturated in plutonium and uranium. At MST concentrations bounding those which are planned for the ITP process, expressions for the maximum loadings (wt %) are determined to be 0.29 - 0.20x[MST] for plutonium and 1.8 - 0.29x[MST] for uranium, where [MST] is the concentration of MST in grams/liter. These expressions are valid over the range of MST concentrations from 0.05 to ...

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

An experimental technique has been developed to examine the interaction between deformation and the exposure of certain high temperature structural alloys to oxidizing molten salt environments. The experimental program involved performing a series of long-term tensile tests over a wide range of strain rates. Fracture strain reduction in area and ultimate strength (UTS) were monitored as parameters indicative of an alloy's susceptibility to environmental degradation. For Incoloy Alloy 800 tested at 600/sup 0/C in the salt medium and at initial strain rates between 2 x 10/sup -7/ sec/sup -1/ and 1 x 10/sup -5/ sec/sup -/1 no appreciable loss of ductility, as measured by reduction in area, was observed relative to control specimens tested in air at the same temperature and strain rates. Similarly, fracture strain and UTS were essentially unaffected by exposure to the oxidizing environment. The structure of the oxide ...

International Nuclear Information System (INIS)

It is shown that bending tests on microsamples can be used to study the conditions in which hydrogen brittleness develops. In such tests hydrogen brittleness develops in the VTI5 alloy within the temperature range +5 to -20"0C. The tendency of VTI5 to develop hydrogen brittleness is enhanced with bending in salt water. (author).

Science.gov (United States)

Norepinephrine stimulates the growth of a range of bacterial species in nutritionally poor SAPI minimal salts medium containing 30% serum. Addition of size-fractionated serum components to SAPI medium indicated that transferrin was required for norepinephrine stimulation of growth of Escherichia coli. Since bacteriostasis by serum is primarily due to the iron-withholding capacity of transferrin, we considered the possibility that norepinephrine can overcome this effect by supplying transferrin-bound iron for growth. Incubation with concentrations of norepinephrine that stimulated bacterial growth in serum-SAPI medium resulted in loss of bound iron from iron-saturated transferrin, as indicated by the appearance of monoferric and apo- isoforms upon electrophoresis in denaturing gels. Norepinephrine also caused the loss of iron from lactoferrin. The pharmacologically inactive metabolite norepinephrine 3-O-sulfate, by contrast, did not result in ...

Energy Technology Data Exchange (ETDEWEB)

The effects of TANOL radical have been examined on chemical shifts and relaxation rates of /sup 109/Ag NMR in aqueous solution of silver salts. The silver ion in aqueous solution is found to coordinate with TANOL radical. A small amount of TANOL is added as a doping agent(0.020M), since /sup 109/Ag signals are obtained for (1.0M) silver ion within 30 minutes. The /sup 109/Ag chemical shifts of silver salt in aqueous solutions were found within the range of 0 to -1000 ppm relative to that of 1.0M AgNo/sub 3/.

International Nuclear Information System (INIS)

Influence of alkali elements on formation, composition, solubility and region of stability of complex hafnium sulfates, separated in the HfO"2-H"2SO"4-Me"2SO"4-H"2O (Me-Na, K, Rb, Cs and NH"4 group) systems is studied. In all cases hafnium forms the complex sulfates of three types differing by basicity or ratio HfO"2:SO"3 1:1, 1:1.5, 1:2. Three basic and three medium sulfates are crystallized in the systems with sodium; with rubidium, cesium and ammonium - two basic and two medium sulfates and with potassium - two basic and one medium salts. Anhydrous salts do not form in the investigated systems. Potassium salt approximately 0.3% according to HfO"2 is characterized by minimum solubility from the salts of 2HfOSO"4x(1-3)Me"2SO"4x(4-6)xH"2O while solubility of the same salts with rubidium, cesium and sodium increases from (0.25-1.0); (0.5-1.5) till (1.0-5)% ...

Energy Technology Data Exchange (ETDEWEB)

Color formation in aqueous solutions of the ditetrazolium salt blue tetrazolium (BT{sup 2+}) in the absence or presence of oxygen is a complex radiation chemical reaction. The final stable product is the poorly soluble diformazan violet to blue pigment having a broad spectral absorption band ({lambda}{sub max}=552 nm). The reaction of BT{sup 2+} with the hydrated electron proceeds by rapid reduction of BT{sup 2+} followed by protonation at the nitrogen closest to the unsubstituted phenyl group, via the two intermediate tetrazolinyl radicals shared by the ditetrazole ring nitrogens. The effect of solution pH, N{sub 2}O saturation, and the presence of the reducing agent dextrose are examined. The system serves as a radiochromic sensor and a dosimeter of ionizing radiations. Solutions of 5 mmol l{sup -1} BT{sup 2+} at pH 7.3 serve as dosimeters over an absorbed-dose range of approximately 0.2-6 kGy (dearated, with a range of ...

Energy Technology Data Exchange (ETDEWEB)

The initiation and inhibition of pitting corrosion on zirconium and hafnium in aqueous solutions have been investigated by potentiodynamic, potentiostatic and galvanostatic measurements at 25/sup 0/C. Effects of Cl/sup -/, Br/sup -/and I/sup -/ have been examined over a range of salt concentrations and pH. All three halide ions cause pitting attack on the two metals, but this may be inhibited by other anions. The results show that hafnium is more easily protected against pitting than is zirconium. The data are treated by the Butler-Volmer equation to yield more information about the mechanisms of the pitting corrosion.

Energy Technology Data Exchange (ETDEWEB)

Heat-of-fusion storage materials for low temperature latent heat storage in the temperature range 0-120 C are reviewed. Organic and inorganic heat storage materials classified as paraffins, fatty acids, inorganic salt hydrates and eutectic compounds are considered. The melting and freezing behavior of the various substances is investigated using the techniques of Thermal Analysis and Differential Scanning Calorimetry. The importance of thermal cycling tests for establishing the long-term stability of the storage materials is discussed. Finally, some data pertaining to the corrosion compatibility of heat-of-fusion substances with conventional materials of construction is presented.

International Nuclear Information System (INIS)

Relative densities and relative massic heat capacities have been measured for aqueous solutions of Y(ClO_4)_3, Yb(ClO_4)_3, Dy(ClO_4)_3, and Sm(ClO_4)_3 at T=(288.15,298.15,313.15, and 328.15) K and p=0.1 MPa. These measurements were made in the concentration range 0.01624#<=#m/(mol#centre dot#kg"-"1)#<=#0.41822 using a Sodev 02D Vibrating Tube Densimeter and a Picker Microflow Calorimeter, respectively. To counter the potential effects of hydrolysis, aqueous solutions of the investigated salts were acidified with perchloric acid. After correcting for the presence of the acid, the measured properties were used to calculate apparent molar volumes and apparent molar heat capacities for solutions of the perchlorate salts in water. The calculated apparent molar properties were modeled at each investigated temperature using Pitzer ion interaction equations to produce estimates of apparent molar volumes and heat capacities ...

International Nuclear Information System (INIS)

Cholangiocarcinoma is synonymous with bile duct carcinoma, and can originate in a small intrahepatic bile duct (peripheral type), a major intrahepatic duct including the hepatic hills, an extrahepatic duct, or near the papilla of Vater (central type). In a sense bile duct carcinoma of the peripheral type is cholangiocarcinoma of the liver; it has the same gross configuration as hepatocellular carcinoma, resulting in difficulty to differentiate on the CT. The authors studied CT findings of 14 cases of pathologically proven peripheral type cholangiocarcinoma of the liver during the last 4 years. The results were as follows: 1. Of 14 cases, 8 were female and 6 were male, and the age ranged from 5th to 7th decades. 2. Preoperative clinical diagnosis were as follows: hepatoma 8 cases, abscess 5 cases and metastasis 1 case in order of frequency. 3. Diagnosis were ...

Energy Technology Data Exchange (ETDEWEB)

In the San Joaquin River Basin, California, a realtime water quality forecasting model was developed to help improve the management of saline agricultural and wetland drainage to meet water quality objectives. Predicted salt loads from the water quality forecasting model, SJRIODAY, were consistently within +- 11 percent of actual, within +- 14 percent for seven-day forecasts, and with in +- 26 percent for 14-day forecasts for the 16-month trial period. When the 48 days dominated by rainfall/runoff events were eliminated from the data set, the error bar decreased to +- 9 percent for the model and +- 11 percent and +- 17 percent for the seven-day and 14-day forecasts, respectively. Constraints on the use of the model for salinity management on the San Joaquin River include the number of entities that control or influence water quality and the lack of a centralized authority to direct their activities. The lack of real-time monitoring sensors for other primary ...

British Library Electronic Table of Contents (United Kingdom)

The electroreduction process of Zr(IV) was studied at molybdenum electrode in LiCl-KCl-K2ZrF6 molten salt. The transient electrochemical techniques, such as cyclic voltammetry and chronopotenimetry were used. The experimental results showed that the electrochemical reduction of Zr(II)/Zr and Zr(IV)/Zr(II) were both diffusion-controlled process. In the 773-973K range, the diffusion coefficients of Zr(ii) and Zr(IV) were determined: DZr(II)=0.15567exp{-69.65x10^3RT(K)}cm^2/s, DZr(IV)=1.09x10^-^4exp{-44.39x10^3RT(K)}cm^2/s. The activation energy values for the diffusion process were 69.65kJ/mol and 44.39kJ/mol, respectively.

UK PubMed Central (United Kingdom)

BackgroundGlycochenodeoxycholate (GCDA) is one of the major human bile salts. Bile salts stimulate cell survival and proliferation through the mitogen-activated protein kinase, but...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Salt stress elicits betaine accumulation to high levels in species from several diverse dicot families (Chenopodiaceae, Amaranthaceae, Convolvulaceae, Solanaceae, and Asteraceae). FAM-MS studies with deuterated precursors showed that species from all these families synthesize betaine from choline. Enzyme assays and immunotitration data showed that all accumulating species contained betaine aldehyde dehydrogenase (BADH) enzyme activity recognized by antibodies raised against purified BADH isolated from Spinacia oleracea. Immunoblotting indicated that the BADH monomer was in all cases of Mr {approx} 63,000. The similarity of BADH in the different species is consistent with a single evolutionary origin for the betaine pathway. This was supported by the presence in immunoblots of a cross-reacting band at Mr {approx} 63,000 in Magnolia x Soulangiana, a primitive angiosperm.

Energy Technology Data Exchange (ETDEWEB)

Metal nanoparticles have many potential technological applications. Biological routes to the synthesis of these particles have been proposed including production by vascular plants, known as phytoextraction. While many studies have looked at metal uptake by plants, particularly with regard to phytoremediation and hyperaccumulation, few have distinguished between metal deposition and metal salt accumulation. This work describes the uptake of AgNO{sub 3}, Na{sub 3}Ag(S{sub 2}O{sub 3}){sub 2}, and Ag(NH{sub 3}){sub 2}NO{sub 3} solutions by hydroponically grown Brassica juncea and the quantitative measurement of the conversion of these salts to silver metal nanoparticles. Using X-ray absorption near edge spectroscopy (XANES) to determine the metal speciation within the plants, combined with atomic absorption spectroscopy (AAS) for total Ag, the quantity of reduction of Ag{sup I} to Ag{sup 0} is reported. Transmission electron microscopy (TEM) ...

Science.gov (United States)

The aim for deterministic control of the interactions between macroions in aqueous media has motivated widespread experimental and theoretical work. Although it has been well established that like-charged macromolecules can aggregate under the influence of oppositely charged condensing agents, the specific conditions for the stability of such aggregates can only be determined empirically. We examine these conditions, which involve an interplay of electrostatic and osmotic effects, by using a well defined model system composed of F-actin, an anionic rod-like polyelectrolyte, and lysozyme, a cationic globular protein with a charge that can be genetically modified. The structure and stability of actin-lysozyme complexes for different lysozyme charge mutants and salt concentrations are examined by using synchrotron x-ray scattering and molecular dynamics simulations. We provide evidence that supports a structural transition from columnar arrangements of F-actin held ...

International Nuclear Information System (INIS)

Apparent molar volumes of aqueous methyldiethanolamine and its salt were determined with platinum vibrating tube densitometers over a range of temperatures from 283K=range of 283K=salt show increasingly positive and negative values, respectively, at high temperatures and ...

UK PubMed Central (United Kingdom)

Clostridium difficile (C. difficile) is a common causative agent of pseudomembranous colitis (PMC). C. difficile-associated diarrhea (CDAD) ranges...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The use of standard cementitious material creates pulses of pH in the magnitude of 12-13 in the leachates and release alkalis. Such a high pH is detrimental and also unnecessarily complicates the safety analysis of the repository. As no reliable pH-plume models exist, the use of products giving a pH below 11 in the leachates facilitates the safety analysis. Also, according to current understanding, the use of low-pH cement (pH = 11) will not disturb the functioning of the bentonite, although limiting the amount of low-pH cement is recommended. A result of the project is that there are both low-pH cementitious material for grouting larger fractures (= 100 {mu}m) and non-cementitious material for grouting smaller fractures (< 100 {mu}m) that will, after further optimisation work, be recommended for grouting of deep repositories. This project concentrated on the technical development of properties for the low pH grouts. Long-term safety and environmental aspects and durability of ...

Energy Technology Data Exchange (ETDEWEB)

Motivated by the discovery of superconductivity in alkali and alkaline earth fullerides, this program was undertaken both to understand the nature of and expand the range of materials demonstrating superconductivity. The first approach involved attempts to modify the fullerene cage by incorporating heteroatoms in the structure and the preparation and photophysical properties of nitrogen and sulfur doped fullerenes were studied in detail. The second approach involved examining the stoichiometry and effect of preparative conditions on the behavior of alkali, alkaline earth, lanthanide and mixed ion fullerides. In particular, the authors have elaborated on a technique for making such salts using liquid ammonia or aliphatic amines as solvents. Thirdly, modeling studies were undertaken to predict the properties of heterohedral fullerines and metal - C60 complexes, and theoretical guidelines were developed for understanding the reactivity of the ...

British Library Electronic Table of Contents (United Kingdom)

The influence of headspace solid-phase microextraction (HS-SPME) variables, namely, sample concentration, salt concentration and sample amount, on the equilibrium headspace analysis of the main volatile flavor compounds released from soursop was investigated. A total of 35 volatile compounds, comprising 19 esters, six alcohols, three terpenes, two acids, two aromatics, two ketones and an aldehyde, were identified. The results indicated that all response-surface models were significantly (p<0.05) fitted for 10 target volatile flavor compounds. The results further indicated that more than 65% of the variation in the equilibrium headspace concentrations of target volatile flavor compounds could be explained by the final reduced models, with high R2 values ranging from 0.658 to 0.944. Multiple...

International Nuclear Information System (INIS)

Doping of manganese (Mn3+/Mn4+) into the Aurivillius phase Pb1-xBi4+xTi4-xMnxO15 was carried out using the molten salt technique for various Mn concentrations (x=0, 0.2, 0.4, 0.6, 0.8, and 1). Single phase samples could be obtained in the composition range with x up to 0.6 as confirmed by X-ray and neutron diffraction analysis. Dielectric measurements show a peak at 801, 803, 813 and 850 K for samples with x=0, 0.2, 0.4, and 0.6, respectively, related to the ferroelectric transition temperature (Tc). The main contribution of the in-plane polarization for x?0.2 which was calculated from the atomic positions obtained by the structure analysis is the dipole moment in the Ti(1)O6 layer; however, for x?0.4 the polarization originates from the dipole moment in the Ti(2)O6 layer. Mn doping in the Pb1-xBi4+xTi4-xMnxO15 does not show any long range magnetic ordering. -- Graphical abstract: The dipole moment of TiO6 dependence of x ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

For the advanced fusion reactor FFHR2 (Force Free Helical Reactor) that has been proposed by NIFS, molten salt Flibe (LiF:BeF2=64:36) breeder blanket system is selected because of Flibe's features such as chemical stability, low-pressure operation and low electric conductivity. The Flibe is however high Prandtl number fluid since it has high viscosity and low thermal conductivity. Therefore its heat transfer performance is low compared with liquid Li or Pb-Li. In addition to heat removal of 1MW/m2 on the first wall, electrolysis of molten salt due to MHD effect will take place under high flow rate condition. This indicates that heat transfer enhancement under low flow rate is essential for the Flibe blanket system. In our laboratory, heat transfer characteristics of molten salt HTS (KNO3:NaNO2:NaNO3=53:40:7), have been evaluated, which is used as a simulant fluid of Flibe from the points of view of Be's toxicity and similar ...

CERN Document Server

We review the interplay of frustration and strong electronic correlations in quasi-two-dimensional organic charge transfer salts, such as k-(BEDT-TTF)_2X and Et_nMe_{4-n}Pn[Pd(dmit)2]2. These two forces drive a range of exotic phases including spin liquids, valence bond crystals, pseudogapped metals, and unconventional superconductivity. Of particular interest is that in several materials there is a direct transition as a function of pressure from a spin liquid Mott insulating state to a superconducting state. Experiments on these materials raise a number of profound questions about the quantum behaviour of frustrated systems, particularly the intimate connection between spin liquids and superconductivity. Insights into these questions have come from a wide range of theoretical techniques including first principles electronic structure, quantum many-body theory and quantum field theory. In this review we introduce the basic ...

International Nuclear Information System (INIS)

Uranium dendrites which were deposited at a solid cathode of an electrorefiner contained a certain amount of salts. These salts should be removed for the recovery of pure metal using a cathode processor. In the uranium deposits from the electrorefining process, there are actinide chlorides and rare earth chlorides in addition to uranium chloride in the LiCl-KCl eutectic salt. The evaporation behaviors of the actinides and rare earth chlorides in the salts should be investigated for the removal of salts in the deposits. Experiments on the salt evaporation of rare earth chlorides in a LiCl-KCl eutectic salt were carried out. Though the vapor pressures of the rare earth chlorides were lower than those of the LiCl and KCl, the rare earth chlorides were co-evaporized with the LiCl-KCl eutectic salt. The Hertz-Langmuir ...

Energy Technology Data Exchange (ETDEWEB)

Objective of the project is characterization of electrode reactions in molten salt by using metal oxides and silica-based electrode. The scope of project are characterization of metal oxide properties in molten salt and miniaturization of 3-electrode electrochemical test cell. Electrochemical micro-cell for actinide-LiCl-KCl molten salt was newly designed. Electroless and electrochemical deposition technique was applied to Mo coating on quartz tube. From the design of electrode and 3-electrode electrochemical cell suitable for the tests in molten salt electrolyte, so it is anticipated to get the information on the electrochemical behavior of metallic electrode in molten salt and to secure the information on oxidation/reduction behavior of actinide

International Nuclear Information System (INIS)

The COSA II (computer codes for salt) benchmark problem has been pursued with the ADINA (Automatic Dynamic Incremental Nonlinear Analysis) program code. With the use of this, the code should be validated by means of experimental data and the ability to reproduce real-life calculation results of the KfK (Kernforschungszentrum Karlsruhe/Nuclear Research Center in Karlsruhe) should be proven. A successful validation of the code then forms the foundation stone for the ability to use different calculation problems in the final (ultimate) storage. This also accompanies the consequent reaction of replacing the STEALTH (Solids and Thermal Hydraulics Code for EPRI Adapted from LAGRANGE TOODY and HEMP) program which has a number of program-specific weaknesses compared to the ADINA computer code. In order to reproduce the approximate values from the KfK, the same values have been used. Differences were evident in the discretion and the selection of the initial values for ...

Energy Technology Data Exchange (ETDEWEB)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after electrochemical surface nitriding, a technique proven to have an effect analogous to N alloying. It was shown that nitrogen, nickel and molybdenum additions independently and in certain combinations stimulate selective dissolution of iron, resulting in a significant enrichment of chromium beneath the passive film. ...

Energy Technology Data Exchange (ETDEWEB)

Recently the authors showed that tetrazolium salts can be obtained during the oxidation of substituted 1,3,5-triarylformazans with potassium permanganate in a two-phase organic solvent-water system. The role of phase-transfer catalyst in this reaction is played by the tetrazolium salt, which is formed in a small amount as the result of oxidation of the formazan at the phase boundary. The method is distinguished by its extreme simplicity. However, the yield of the tetrazolium salts fluctuates within wide limits and does not exceed 62%. This is due to the fact that as the reaction proceeds the pH of the aqueous phase increases from 6 to 12. At the same time it is known that tetrazolium salts are unstable in aqueous alkaline solutions. They found that if the aqueous phase is replaced by aqueous hydrochloric acid (5 wt. %) the yields of the tetrazolium salts (Ia-g) are increased to ...

Energy Technology Data Exchange (ETDEWEB)

The performance of four different organic coating systems applied to carbon and weathering steel coupons has been assessed in this investigation. applied on the surface of carbon steel and weathering steel coupons. The coupons have been evaluated using five different tests, three field tests and two accelerated tests. The field tests were carried out at three atmospheric stations, located at COSIPA in Cubatao-SP, at Alto da Serra in Cubatao-SP and at Paula Souza in Sao Paulo city. The accelerated tests consisted of (a) exposure to alternate cycles of ultraviolet radiation/condensation combined with salt spray cycles (UVCON combined with Salt Spray) and of (b) exposure to alternate cycles of ultraviolet radiation/condensation combined with the Prohesion test. The performance of the coatings was assessed by visual observation and photographs, using a method based on ASTM D-610, ASTM D-714 and ASTM-1654 standards to rank them. The oxide phases ...

Energy Technology Data Exchange (ETDEWEB)

Maximum metal loss rate of Alloy 800 coupons was about 0.5 mil/year and occurred at the maximum temperature of 600/sup 0/C. Significantly greater oxide penetration into the alloy occurred in unabraded as-received tubing. Since the corrosion rate of unabraded tubing was less temperature sensitive than polished coupons, and attained a maximum value at temperatures in the range of 550 to 565/sup 0/C, a value of 1 mil/year should be used as the corrosion rate for design purposes. Because daily thermal cycling is inherent in solar central receiver operation, oxidation and chromium depletion rates can be expected to increase if surface oxide layers spall. The oxide layers formed on Alloy 800 appeared to be adherent, and adherence will benefit further from growth-derived compressive stresses in oxide layers on the salt-exposed inner diameter of receiver tubes. Since the lower duty factor in diurnal solar service may offset the accelerated metal loss ...

Science.gov (United States)

The Bureau of Mines investigated energy-efficient methods for recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite, and carnallite. Six sulfate-chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2 to 22.2% K/sub 2/O, and recoveries from 84 to 99%. Sylvite flotation from chloride evaporites, with amine collector, recovered 90 to 97% of the potash in a concentrate containing 54.3 to 60.3% K/sub 2/O. Fatty acid flotation of the high-sulfate evaporite recovered 78% of the sulfate minerals in a 27.8%-K/sub 2/O concentrate. Flotation of the chloride minerals with amine collector recovered 80% of the potash in a 59.7%-K/sub 2/O concentrate. Solar evaporation of 10,000 gal of brine recovered 99% of the potash in a crude ...

International Nuclear Information System (INIS)

In the early 1980s, AECL built a Waste Treatment Centre (WTC) for managing low-level solid and aqueous liquid wastes for converting CANDU wastes. At present, two liquid waste streams are being treated at the WTC. The liquid waste streams are volume-reduced by a combination of continuous crossflow microfiltration (MF), spiral wound reverse osmosis (SWRO) and tubular reverse osmosis (TRO) membrane technologies. The concentrate produced from the TRO system and the volume-reduced MF backwash solutions are evaporated while simultaneously adding bitumen in a thin-film evaporator. A water-free product of chemical and radiochemical salts and bitumen is removed in 200-L galvanized steel drums for storage. The radiation field of product drums on contact typically has a value of 0.5 to 3 R/h depending upon the feed concentration of radioactivity to the evaporator. The total solids content in the 200-L drum ranges from 25 to 35%. Encapsulated in the ...

International Nuclear Information System (INIS)

The crossed electron-ion beams technique was used to measure absolute cross sections for single ionization of Ar"2"+, Kr"2"+ and Xe"2"+ ions at electron energies ranging from threshold to 2000 eV. In contrast to some previous measurements, the metastable contents of the ion beams were small even in the case of Xe"2"+. All measured cross section curves show significant contributions from excitation-autoionization and possibly direct ionization of inner-shell electrons. There is evidence for resonance-excitation-double-autoionization in the case of Xe"2"+. (author).

Energy Technology Data Exchange (ETDEWEB)

Waste form dissolution studies and preliminary performance analyses were carried out to contribute a part of the data needed for the selection of a waste form for the disposal of Savannah River Plant defense waste in a deep geologic repository. The first portion of this work provides descriptions of the chemical interactions between the waste form and the geologic environment. We reviewed critically the dissolution/leaching data for borosilicate glass and SYNROC. Both chemical kinetic and thermodynamic models were developed to describe the dissolution process of these candidate waste forms so as to establish a fundamental basis for interpretation of experimental data and to provide directions for future experiments. The complementary second portion of this work is an assessment of the impacts of alternate waste forms upon the consequences of disposal in various proposed geological media. Employing systems analysis methodology, we began to evaluate the performance of a generic waste ...

Energy Technology Data Exchange (ETDEWEB)

An air conditioner intakes open-air from an open-air intake port to remove sands and sea salt particles by air filters. Then, natural and artificial radioactive particles of less than 1 {mu}m are removed by high performance particulate filters. After controlling the temperature by an air heater or an air cooler, air is sent to each of chambers in a facility under pressure elevation by a blower. In this case, glass fibers are used as the filter material for the high performance particulate filter, which has a performance of more than 99.97% for the particles of 0.3 {mu}m grain size. Since this can sufficiently remove the natural radioactive materials intruded from the outside, a detection limit value in each of the chambers of the facility can be set 10{sup -13} to 10{sup -14} {mu}ci/cm{sup 3} in respect of radiation control. Accordingly, radiation control can be conducted smoothly and appropriately. (I.N.).

Energy Technology Data Exchange (ETDEWEB)

The purpose of the conversion process is to convert the {sup 233}U fluoride compounds that are being extracted from the Molten Salt Reactor Experiment (MSRE) equipment to a stable oxide for long-term storage at Bldg. 3019.

UK PubMed Central (United Kingdom)

The conformation of the self-complimentary DNA dodecamer d(br5CGbr5CGAATTbr5CGbr5CG) has been investigated in a variety of salt and solvent conditions by one and two-dimensional 1H NMR. In low salt...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The effect of associative interactions of monomers and propagating macroradicals in homopolymerization of N-[3-(dimethylamino)propyl]methacrylamide salts and their copolymerization with acrylonitrile and acrylamide in aqueous solution was studied.

Energy Technology Data Exchange (ETDEWEB)

The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the model -- one for the ...

UK PubMed Central (United Kingdom)

This study examined the genetic basis of hypertension and renal disease in Dahl SS/Mcwi (Dahl Salt-Sensitive) rats using a complete chromosome substitution panel of consomic rats in which each of the...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

YIG precursor powder was obtained by homogeneous precipitation in chloride salt solution by thermal decomposition of urea. It was found that ferric ions precipitated prior to yttrium ions. The precipitate was minute and spherical in shape. The precipitate formed consisted of the mixture of amorphous and ferric oxyhydroxide. Crystallization of YIG was proceeded by solid state reaction of intermediate YFeO{sub 3} and Fe{sub 2}O{sub 3} in the temperature range of 850 deg. C to 1400 deg. C. Single phase of YIG was obtained by heat-treatment of the powder at 1400 deg. C for 6 hrs in air. The powder calcined was molded into pellets and sintered in air. The maximum density of 4.92 g/cm{sup 3} (95.1% of theoretical density) was obtainable for the pellet sintered at 1450 deg. C using the powder calcined at 900 deg. C. (author) 20 refs., 8 figs., 1 tab.

British Library Electronic Table of Contents (United Kingdom)

Headspace solid-phase microextraction (HS-SPME) coupled to comprehensive two-dimensional gas chromatography time-of-flight mass spectrometry (GCxGC-TOFMS) was applied for equilibrium headspace analysis of Malaysian soursop (Annona muricata) volatile flavor compounds. A two-level fractional factorial design (25-1) was used to determine the effect of SPME variables, namely, SPME fibers, adsorption temperature, extraction time, amount of salt, sample amount and sample concentration on the extraction efficiency of volatile flavor compounds. A total of 37 volatile compounds were identified, comprising 21 esters, 6 alcohols, 3 terpenes, 2 acids, 2 ketones, 2 aldehydes and an aromatic with different hydrophobicities (log P) ranging between -0.14 and 4.83. Extraction using 10g of diluted (5% w/w) ...

International Nuclear Information System (INIS)

Human complement protein C9 is shown to be a metalloprotein that binds 1 mol of Ca"2"+/mol of C9 with a dissociation constant of 3 #mu#m as measured by equilibrium dialysis. Incubation with EDTA removes the bound calcium, resulting in a apoprotein with decreased thermal stability. This loss in stability leads to aggregation and, therefore, to loss of hemolytic activity upon heating to a few degrees above the physiological temperature. Heat-induced aggregation of apoC9 can be prevented by salts that stabilize proteins according to the Hofmeister series of lyotropic ions, suggesting that the ion in native C9 may ligand with more than one structural element of domain of the protein. Ligand blotting indicates that the calcium binding site is located in the amino-terminal half of the protein. Removal of calcium by inclusion of EDTA in assay mixtures has no effect on the hemolytic activity of C9, and its capacity to bind to C8 in solution, or to small unilamellar lipid ...

Science.gov (United States)

A miniature, high-voltage, thermally activated battery has been developed. This battery weighs 41 grams, occupies a volume of 16.4 cu cm, and contains two separate 500-v channels, each designed to charge a 5.25 microfarad capacitor within 300 milli-seconds and remain operational under a 640-kohm load for a minimum of 28 seconds over the temperature range from +16 to +71 C. The electrochemical system utilizes a calcium anode, LiCl-KCl molten salt electrolyte, a CaCrO4-K2CrO4 mixture as the depolarizer or active cathode material, and an iron cathode. The depolarizer and electrolyte, along with a silica binder, are formed into homogeneous pellets, and these pellets are stacked alternately with calcium-iron bimetal disks in beryllium oxide tubes to form cell stacks. The cells are activated by an iron-potassium perchlorate pyrotechnic heat source external to the BeO tubes.

Energy Technology Data Exchange (ETDEWEB)

Extra-fine powdered activated charcoal has been used as stationary phase (coating layer) in solid-phase microextraction (SPME). The efficiency and reliability of the prepared device have been investigated for the extraction of some volatile organic compounds such as benzene, toluene, ethylbenzene and xylene isomers (BTEX) from the headspace of water samples. Monitoring of the extracted compounds and further quantitative analysis of the real samples have been performed by capillary GC-FID. Effects of several factors such as temperature, addition of salt, and stirring speed on extraction efficiency and exposure time have been studied. Under optimum conditions, extraction recoveries for these compounds from 50 mL water were >95%. The calibration graphs were linear in the range 5 to 10{sup 4} pg mL{sup -1} and the detection limit for each BTEX compound was 1.5-2 pg mL{sup -1}. The results obtained by use of this porous layer activated charcoal ...

International Nuclear Information System (INIS)

Russian (Jul 1974). USSR Buslaev, Yu.A. Petrosyants, SP Tarasov,

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Serum ferritin levels were measured in 72 normal subjects and in 214 cases with various diseases by an immunoradiometric assay. In normal subjects, the serum ferritin levels were 27-230 ng/ml. Elevated serum ferritins were observed in most cases with iron excess and acute hepatitis. Markedly elevated levels were found in the majority of cases with acute leukemia, malignant lymphoma, hepatoma, and pancreatic cancer. High ferritin levels were also found in other malignant diseases. However, the range overlapped broadly with that of nonmalignant diseases. The serum ferritin correlated significantly with serum iron in normals and in those with iron deficiency anemia. In most nonmalignant cases, the serum ferritin and iron levels distributed on a regression line obtained from levels in normals and those with iron deficiency anemia. However, 92% of the malignant cases ...

Energy Technology Data Exchange (ETDEWEB)

The neutron detector is cased in a metal envelop and has one detector with a very sensitive fission chamber and a second detector with a fission chamber less sensitive that the first one and a boron coated ionisation chamber for reducing gamma radiation detection.

Energy Technology Data Exchange (ETDEWEB)

One of the effective methods of deep modification of the surface of steels and alloys is the combination of ion implantation and plasma nitriding. In this work, the long-range effect is demonstrated in the case of combination of the effect of high- and low-energy ions of nitrogen on a martensitic steel for each ion implantation is usually not effective, and a titanium alloy used widely in industry.

Environmental Research Database

DescriptionThe objective of this project is to relate the processing quality of wheat to the composition of the developing and mature grain using material grown under a range of nutrient regimes including long term organic and fertilised systems from the Rothamsted Broadbalk experiment, variety trials and organically grown wheat. Preliminary studies have indicated substantial differences in the transcriptome profiles of wheat grown with artificial fertiliser and with organic fertiliser on Broadbalk and tru [continued...

Energy Technology Data Exchange (ETDEWEB)

An integrated voltage regulator and power system stabilizer based on one step ahead prediction is presented. The fixed parameter predictive control scheme is shown capable of providing consistently good voltage response and contribution to system damping over a wide range of operating conditions and system configuration. This is in contrast to the case with conventional automatic voltage regulator and power system stabilizer where performance varies widely with the operating situation and can even cause system instability. (author)

Energy Technology Data Exchange (ETDEWEB)

Applications of molten salts technology to separation and synthesis of materials have been studied eagerly, which would develop new fields of materials science. Research Group for Actinides Science, Department of Materials Science, Japan Atomic Energy Research Institute (JAERI), together with Reprocessing and Recycle Technology Division, Atomic Energy Society of Japan, organized the Workshop on Molten Salts Technology and Computer Simulation at Tokai Research Establishment, JAERI on July 18, 2001. In the workshop eleven lectures were made and lively discussions were there on the fundamentals and applications of the molten salts technology that covered the structure and basic properties of molten salts, the pyrochemical reprocessing technology and the relevant computer simulation. The 10 of the presented papers are indexed individually. (J.P.N.)

Energy Technology Data Exchange (ETDEWEB)

In the electrorefining step of the pyrochemical process, actinide ions dissolved in the LiCl-KCl eutectic salt are recovered as pure actinide metals at a cathode for a re-use as a nuclear fuel from the aspect of its nonproliferation of the nuclear fuel cycles. The lanthanide species dissolved in the LiCl-KCl eutectic salt play an important role in an effective metal purification during the electrorefining step, so it is necessary to understand the chemical and physical behaviors of lanthanides in molten salt. The in situ spectroscopic measurement system and studies according to temperature changes are essential for better understandable information. To our knowledge, the absorption studies of lanthanides at high temperatures have been reported before, but the fluorescence studies of those at high temperature are not reported yet. We will discuss here the fluorescence behaviors of lanthanides in LiCl-KCl molten ...

International Nuclear Information System (INIS)

Identification of factors that determine individual patient risk for recurrence and progression in superficial papillary carcinoma of the bladder is a subject of extensive research as it would be a major outcome in patient management. It has been well recognized that traditional prognostic markers as tumor grade and stage are not accurate enough in predicting biological behavior. A large number of markers have been investigated as potential prognostic factors and relatively few can help in predicting outcome. Material and Methods: Forty-nine cases undergoing complete transurethral resection for primary superficial papillary transitional cell carcinoma were subjected to clinicopathologic evaluation as well as immunohistochemical staining for p53, bcl-2, cytokeratin 20 and Ki-67. The CAS-200 image analyzer was used to estimate the Ki-67 labeling index. Results: Recurrence was observed in 19 cases (38.8%) and progression in 7 ...

International Nuclear Information System (INIS)

The purpose of this work was to study and quantify the differences in dose distributions computed with some of the newest dose calculation algorithms available in commercial planning systems. The study was done for clinical cases originally calculated with pencil beam convolution (PBC) where large density inhomogeneities were present. Three other dose algorithms were used: a pencil beam like algorithm, the anisotropic analytic algorithm (AAA), a convolution superposition algorithm, collapsed cone convolution (CCC), and a Monte Carlo program, voxel Monte Carlo (VMC++). The dose calculation algorithms were compared under static field irradiations at 6 MV and 15 MV using multileaf collimators and hard wedges where necessary. Five clinical cases were studied: three lung and two breast cases. We found that, in terms of accuracy, the CCC algorithm performed better overall than AAA compared to VMC++, but AAA remains an attractive ...

Energy Technology Data Exchange (ETDEWEB)

Manganese is an essential metal of toxicologic concern primarily because of exposure via inhalation. Environmental forms of Mn exist mainly as insoluble oxides, yet much of the research information available relates to the soluble salts. In the present study, adult male Sprague-Dawley rats were intratracheally instilled with either soluble MnCl/sub 2/ or insoluble Mn/sub 3/O/sub 4/ labeled with /sup 54/Mn. Lungs and other major organs were sampled over a span of 3 mo after dosing with the respective chemicals, which were equivalent to 8 ..mu..Ci and 1 ..mu..mol of manganese in 0.2 ml of buffer. There was rapid clearance of Mn from the lungs in the case of both chemicals; the chloride cleared at an initial rate of nearly four times that of the oxide. Despite this early difference, the amount of /sup 54/Mn remaining in the lungs after 2 wk was similar for both compounds. The level of /sup 54/Mn in the liver, kidney, spleen, and testes peaked at ...

Energy Technology Data Exchange (ETDEWEB)

Six patients with eosinophilic granuloma were studied retrospectively in order to correlate the MRI appearances with the pathology. Ages ranged from 2 years 6 months to 11 years. The bones involved were the humerus, ulna, radius, femur, clavicle and ilium. Plain films, MRI and pathology specimens were obtained. A lytic lesion with indistinct margins, endosteal erosions and periosteal reaction was seen in all cases on plain radiographs. Bone marrow signal was decreased on T1-weighted images and increased on T2-weighted images throughout the bony lesion in all cases. T2-weighted images showed extensive soft-tissue abnormalities suggesting inflammatory changes in four cases. In two cases abnormalities were limited. Extensive changes correlated histologically with an early phase lesion. Localized minor changes were associated with a mid-phase lesion. Inflammatory soft-tissue changes ...

Energy Technology Data Exchange (ETDEWEB)

Development of a number of original 3-D migration methods and algorithms is described. The computational efficiency of these algorithms is demonstrated by implementing them on vector and parallel supercomputers. Two-dimensional post-stack and pre-stack depth migration algorithms in the frequency - space domain using implicit finite difference method were also developed and implemented on a parallel computer, and adapted for applications that range from deep crustal imaging of seismic wavefields that involve wide ranging travel times and frequencies. All implicit finite difference migration algorithms were highly prallelized . The one pass 3-D post-stack depth migration algorithm was extensively used for imaging of seismic monitoring data from Cold Lake, Alberta. Experience shows that it provides the right trade-off between accuracy and computational efficiency. A new formulation of the 3-D reverse-time migration method was developed using ...

International Nuclear Information System (INIS)

In this paper, the widely used models of Taitel-Dukler and Weisman et al. are extrapolated to microgravity levels to compare predicted flow pattern boundaries for horizontal and vertical flows. Efforts have been made to analyze how the two-phase flow models available in the literature predict flow regime transitions in microgravity. The models of Taitel-Dukler and Weisman et al. have been found to be more suitable for extrapolation to a wide range of system parameters than the other two-phase flow regime maps available in the literature. The original criteria for all cases are used to predict the transition lines, except for the transition to dispersed flow regime in case of the Weisman model for horizontal flow. The constant 0.97 on the righthand side of this correlation should be two times that value, i.e., 1.94, in order to match this transition line in their original paper.

International Nuclear Information System (INIS)

The influence of 3d-transition metal impurities on the superconducting properties of the A-15 compounds V_3Si and V_3Ga have been investigated. In the case of V_3Si, the Fe impurities replacing V were found to have a local moment. A compensation effect was found in this case, resulting in a 20KOe increase in the upper critical field at dilute concentrations of Fe. It was demonstrated that long range order V_3Ga possessed higher transition temperature and upper critical field than found hitherto. Investigations on Nb_3Ge/sub 1-x/Ga/sub x/ films obtained by chemical vapor deposition has clearly shown the relation between the transition temperature and structural characteristics. The influence of generalized defects on the superconducting properties in A-15 type Nb_3X compounds has been discussed.

Energy Technology Data Exchange (ETDEWEB)

The evolution of Bianchi type-I and type-IX universes for a theory of gravity with an {epsilon}{ital R}{sup 2} term added to the usual Lagrangian is considered. As in the spatially flat Robertson-Walker case considered previously by others, inflation is found to occur. For any amount of initial anisotropy, the anisotropy decays quickly relative to the length of the inflationary epoch, and the amount of expansion is enhanced by the anisotropy. The exceptions are Bianchi type-IX universes near or at isotropy. In these cases a wide range of initial parameters causes the universe to recollapse, thus reducing the phase space in which inflation can occur. The diagonal metric is shown to be the most general form in the {ital R}{sup 2} theory for both Bianchi type-I universes with a perfect fluid and vacuum Bianchi type-IX models.

Energy Technology Data Exchange (ETDEWEB)

The intrinsic energy levels in the doubly odd isotopes of Np with mass number 238 and of Am with mass numbers 240, 242 and 244 are calculated using the zero-range neutron-proton residual interaction whose parameters are evaluated using the atomic masses and the ground state Gallagher-Moszkowski splitting energy in each case. A configuration dependence of the residual interaction is in evidence in several cases. The results are compared with the experimental data and the comparison is used to check on the two-particle configuration assignments to the intrinsic states in the respective spectra. Encouraged by the nature and the degree of the agreement of the theory with the available experimental data, predictions are made about the expected location of the as yet unobserved two-quasiparticle states in these nuclei.

Energy Technology Data Exchange (ETDEWEB)

The performance of five well-known photosynthesis-light equations is compared by presenting a wide range of solutions in the form of dimensionless nomographs for the case where photosynthetically available radiation (PAR) reduces exponentially down the water column and is distributed sinusoidally through the photoperiod. These provide a simple means of calculating daily photosynthesis at any depth (e.g. at a benthic layer), or through a water column, avoiding the need to perform complex integrations. An examination is made of the accuracy of common approximate methods for calculating daily photosynthesis, assuming constant PAR. For optically deep water a modification is proposed to Talling's planimetric solution, to enable daily photosynthesis to be calculated more accurately, yet simply, over the whole range of possible PAR values. The errors induced by approximating the daily PAR distribution as a half-sinusoid ...

Energy Technology Data Exchange (ETDEWEB)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO{sub 2}, PrO{sub 2}), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The conversion efficiencies of the rare earth elements ...

Energy Technology Data Exchange (ETDEWEB)

The patent is for a method of preparing drilling muds that are notable for their chemical resistance to Zechstein deposits, especially to magnesium, carbonate and carboxylic acid ions. To achieve chemical resistance of the drilling mud to Zechstein deposits, it is suggested to saturate them with salt (the amount of added salt depends on the absorption properties of the solution), and then to process them with caustic soda or potassium oxide hydrate and lime in proportions that would cause filtrate alkalinity not to exceed 0.5. For example, to prepare drilling solution to bore through mediums containing magnesium salts, potassium salts, rock salt, anhydrate, dolomite, limestone, red salt clay: add 340 kg potassium chloride into 1 m/sup 3/ drilling solution with weighed bentonic clay, 10 kg. ferro-chromate lignosulfite, 7 kg. unslaked lime, 2 kg. sodium hydroxide, ...

Energy Technology Data Exchange (ETDEWEB)

Experimental data on the gas holdup and the mean bubble size in a bubble column with a single nozzle was obtained for gas-molten salt systems of a eutectic mixture of LiCl (58 mol %)-KCl (42 mol %) and molten NaNO/sub 3/. The liquid-phase mass transfer coefficient K /SUB L/ was evaluated from the specific surface area a and the volumetric coefficient K /SUB L/ a data for oxygen and carbon dioxide absorption into molten NaNO/sub 3/. The dimensionless correlations of the performance of bubble columns for aqueous solutions can be extended to the gas-molten salt systems.

International Nuclear Information System (INIS)

Lithium was selectively extracted from near-neutral aqueous solutions of alkali metal salts. The mechanism by which this was achieved involves the formation of the trioctylphosphine oxide adduct of a lithium chelate of a fluorinated #beta#-diketone, which is then readily extractable into an organic diluent. High separation factors were obtained from sodium, potassium, rubidium, and cesium. The selectivity of the fluorinated #beta#-diketones for lithium over the alkaline earths was found to be poor. A suggested general flowsheet for the recovery of lithium from a salt brine concentrate is included. (author).

CERN Document Server

We study the expected properties of starbursts in order to provide the point of reference for interpretation of high-z galaxy surveys and of very metal-poor galaxies. We concentrate mainly on the UV characteristics such as the ionizing spectra, the UV continuum, the Ly alpha and HeII 1640 A line and two-photon continuum emission. We use evolutionary synthesis models covering metallicities from Pop III to solar and a wide range of IMFs. We also combine the synthetic SEDs with the CLOUDY photoionization code for more accurate predictions of nebular emission, and to study possible departures from case B assumed in the synthesis models. The ionizing fluxes, UV continuum properties, and predicted Ly alpha and HeII 1640 A line strengths are presented for synthesis models covering a wider range of parameter space than our earlier calculations. Strong departures from case B predictions are obtained for Ly alpha ...

Energy Technology Data Exchange (ETDEWEB)

An oxidative precipitation reaction of rare-earth chlorides in a LiCl-KCl molten salt was successfully carried out by a lab-scale apparatus. The conversion efficiency of the used rare earth chlorides into the insoluble precipitates was increased with the sparging time and temperature and was affected on oxygen sparger type. In the conditions of 700 .deg. C molten salt temperature and above 540min sparging time, the final conversion efficiencies were over 99% for all the experimented rare-earth chlorides. The hydrodynamic characteristics of an oxygen-molten salt two phase flow system are very important for a co-oxidative precipitation of rare earth elements.

Energy Technology Data Exchange (ETDEWEB)

Results are presented from a numerical model of the steady-state energy transfer in molten-salt-in-tube solar cavity receivers that includes convective energy transfer at a local (spatially resolved) level. Molten salt energy absorption and gray radiative transfer between all cavity surfaces are also included. This model is applied to the Molten Salt Subsystem Component Test Experiment (MSS/CTE) cavity receiver. Results for this receiver indicate the global (entire cavity) receiver thermal efficiency is invariant within a few percent to most parameters investigated, although front surface temperatures of the nonabsorbing walls vary considerably, and are particularly sensitive to the type of convective submodel used. Absorption efficiencies indicate the effects of the cavity enclosure environment. For all conditions investigated, tube inner wall temperatures remain under 855 K, ensuring that the salt ...

Science.gov (United States)

Adipocyte lipid-binding protein (ALBP or aP2) is an intracellular fatty acid-binding protein that is

International Nuclear Information System (INIS)

The electrochemical/spectroscopic integrated measurement system was designed and set up for spectro-electrochemical measurements of lanthanide and actinide ions in high temperature molten salt media. A compact electrochemical cell and electrode system was also developed for the minimization of reactants, and consequently minimization of radioactive waste generation. By applying these equipment, oxidation and reduction behavior of lanthanide and actinide ions in molten salt media have been made. Also, thermodynamic parameter values are determined by interpreting the results obtained from electrochemical measurements. Several lanthanide ions exhibited fluorescence properties in molten salt. Also, UV-VIS measurement provided the detailed information regarding the oxidation states of lanthanide and actinide ions in high temperature molten salt media

Energy Technology Data Exchange (ETDEWEB)

To our knowledge, the fluorescence studies of lanthanides in LiCl-KCl eutectic molten salt at a high temperature are not reported yet. The fluorescence of the lanthanide-ions was generally decreased when the temperature was increased. Moreover, the fluorescence of the lanthanides was strong when the sample was solidified to or from the melt. The temperature, where the fluorescence was decreased, was identified to be different depending on the species of the lanthanides and the substrates was considered to possibly be from quenching of the fluorescence due to either the collisions of melted samples induced by high temperature media or the re-absorption of fluorescence by the samples. Several comparison experiments were performed to explain and understand this phenomenon and improve the fluorescence. In this way, an on-line monitoring of chemical species and the concentration for lanthanides elements in molten salt media of pyrochemical process ...

Science.gov (United States)

Ultimate Compressive Strength of Short Sheet - Stringer Panels With Special. Reference to the Influence of the Riveted Connection Between Sheet and Stringer ...

Science.gov (United States)

... 3004505040***, MEDICAMENTS, DOSED, VITAMINS, MULTIPLE, OTHER COMBINATIONS, FD3***. 3104100000**, CARNALLITE, SYLVITE AND OTHER CRUDE POTASSIUM SALTS, FD3**. ...

International Nuclear Information System (INIS)

Pyrochemical processing of nuclear fuels using molten salts has attracted much attention because of its potential to be applied for a future spent nuclear fuel management. In the pyrochemical processing, there are a number of steps to electro-refine and electro-win each element of lanthanides and actinides, commonly called trans-uranic elements (TRU). In order to materialize the pyrochemical processing in the nuclear power plant environments, qualitatively and quantitatively monitoring of each elements is necessary. Thus, we have undertaken to develop an on-line observing system of the TRU in LiCl-KCl molten salt media by using electrochemical and spectroscopic methods. In this work, the electrochemical and spectroscopic behaviors of europium as a proxy material for TRU were investigated simultaneously in the LiCl-KCl molten salt

Science.gov (United States)

Interactions (FCCI) University of Wisconsin, Madison Thermal Properties of LiCl-KCl Molten Salt for Nuclear Waste Separation University of Wisconsin, Madison Next Generation...

Energy Technology Data Exchange (ETDEWEB)

The properties of a helium film on the surface of solid parahydrogen are investigated. It is shown that wetting of the solid hydrogen by the liquid helium occurs. The transport velocities along the He II film on the solid parahydrogen surface are measured in broad temperature, film height, and level difference ranges. It is shown that the transport velocity in this case has the least value as compared with its value on other substrates. The thickness of the helium-saturated film is determined on the solid hydrogen surface on the basis of the data obtained, and the value is in good agreement with the results of a computation performed within the framework of the Frenkel' theory.

Energy Technology Data Exchange (ETDEWEB)

Currently it can be observed that in the case of generator drives as well as 'mechanical drives' smaller units are demanded with a steam turbine capacity of up to 150 MW and clearly higher efficiencies. MAN TURBO is meeting the challenge through realisation of a comprehensive development project aiming at the extension of the application range of the current steam turbine series.

International Nuclear Information System (INIS)

The magnetorheological suspension (MRS) brake is of the monoblock type. The main part of the electromagnetic brake is an electromagnet, between whose poles two MRS disks are placed. For distances between disks of 0.65x10"-"3 m#+-#10%, revolutions of the electric motor, coupled to the electromagnetic brake, ranging between 200 and 1600 rev/min and braking powers of up to 85 W, there are no differences in revolutions between the disks of the electromagnetic brake. For fixed revolutions of the electric motor, the revolution of the parallel disk can be modified continuously by means of the intensity of the magnetic field. In all cases, the quantity of MRS is of 0.35x10"-"3 kg.

International Nuclear Information System (INIS)

By the methods of small-angle X-ray scattering and translucent electron microscopy the existence of inhomogeneity of electron density in hydrogenated films of amorphous silicon is confirmed. The decreased density regions are extended and form a branched network of channels oriented mostly by the normal direction to the films surface. The typical size of the decreased density regions network constitutes 10 nm in the 100-800 nm films thickness range. The increase of hydrogen total partial pressure in gas mixture in case of films growth results at first in the decrease of extension of these regions and than to micropores generation in the network nodal points of the decreased electron density regions.

Energy Technology Data Exchange (ETDEWEB)

This paper describes an exact solution to the problem of absorbing nitrogen dioxide into aqueous solution, in which case the nitrogen dioxide concentration is allowed to vary over a wide range. The authors have worked on the rate of calcium sulfate dihydrate scale formation on the reverse osmosis membrane and find this phenomena can be treated by the crystallization theory. The authors performed long-term experiments using calcium sulfate dihydrate solution with addition of sodium hexametaphosphate (SHMP) and commercially available organophosphates and investigated the mechanism of the inhibitor's action quantitatively.

Science.gov (United States)

In this paper, model analysis into the time-dependent transmembrane potential at the outer cell membrane is presented, for applied high-intensity electric pulses having durations in the nanosecond range or smaller. It is argued that the frequency-dependent dielectric response of cell membranes could be used to advantage for stronger bioeffects by employing shorter pulses. Our model calculations predict faster transmembrane voltages and larger electroporation densities for a given external energy with pulse durations in the subnanosecond regime. This temporal regime would be used, for example, in the electrotherapy of mixed cell ensembles having different dielectric response properties. PMID:21937300

Energy Technology Data Exchange (ETDEWEB)

Aim: To investigate interpretative accuracy and reporting time for radiologists performing computed tomography (CT) colonography in day-to-day non-academic clinical practice. Materials and methods: Thirteen radiologists from seven centres, who were reporting CT colonography in non-academic daily clinical practice, interpreted a dataset of 15 colonoscopically validated cases in a controlled environment. Ten cases had either a cancer or polyp >10 mm; one case had a medium polyp and four were normal. Correct case categorization and interpretation times were compared using analysis of variance to aggregated results obtained from both experienced observers and observers recently trained using 50 cases, working in an academic environment. The effect of experience was determined using Spearman's rank correlation. Results: Individual accuracy was highly variable, ...

International Nuclear Information System (INIS)

Selective alveolo-bronchography (SAB) has been routinely used to evaluate anatomical changes in the bronchiole and its distal air spaces. A narrowing of the bronchiole and abnormal pooling of contrast medium in the destroyed air space are the prime findings. Since the object of radiography is extremely thin, direct magnification radiography is mandatory to obtain radiologic details. However, the problem with this technique is that radiographic quality varies depending upon the size of the patient and the concentration of contrast medium to be introduced in the lung. This study had two goals. One was to improve the image quality of SAB by Fuji Computed Radiography (FCR). FCR provides radiographs with a good contrast and stable density throughout a wide range of exposure factors which occur in the use of SAB. The other goal was to separately evaluate morphological abnormalities in the outer and inner zones of the lung using X-ray CT. This idea was derived from our ...

International Nuclear Information System (INIS)

In an epidemiological study of the somatic late effects risk following incorporation of a short lived #alpha#-emitter, 1473 ankylosing spondylitis patients treated with repeated intravenous injections of "2"2"4Ra in the years 1948 - 75, have been observed in the GSF. The usual therapeutic plan consisted of a total of 10 - 12 injections of 1.036 MBq (28 #mu#Ci) of "2"2"4Ra each, given at weekly intervals; this would result in an cumulative #alpha#-dose of 0.56 - 0.67 Gy to the marrow-free skeleton of a 70-kg-man (standard man). These patients have been followed together with a control group of ankylosing spondylitis patients not treated with radioactive drugs and/or X-rays. Until May 1993 (mean follow-up time 19.9 yr), 595 patients of the exposure group and 722 patients of the control group have died, causes of death have been ascertained for 578, resp. 668 patients. Among others we observed in the exposure group 10 cases of leukaemia (vs. 2.7 - 2.8 ...

Energy Technology Data Exchange (ETDEWEB)

This study examines the sensitivity of the travel time distribution predicted by a reference case model to (1) scale of representation of the model parameters, (2) size of the model domain, (3) correlation range of log-transmissivity, and (4) cross correlations between transmissivity and effective thickness. The basis for the reference model is the preliminary stochastic travel time model previously documented by the Basalt Waste Isolation Project. Results of this study show the following. The variability of the predicted travel times can be adequately represented when the ratio between the size of the zones used to represent the model parameters and the log-transmissivity correlation range is less than about one-fifth. The size of the model domain and the types of boundary conditions can have a strong impact on the distribution of travel times. Longer log-transmissivity correlation ranges cause larger ...

Energy Technology Data Exchange (ETDEWEB)

Processing in the Defense Waste Processing Facility (DWPF) is controlled by constraints on predicted properties of the product glass. One of these properties is chemical durability, which is measured as the response of various glass constituents to the seven-day Product Consistency Test (PCT) [1]. As currently implemented into the DWPF`s Product Composition Control System (PCCS) the response of boron is taken as representative of all of the constituent responses, and control is in terms of the boron response. This response, in normalized units and in log scale, is taken to be a linear function of the glass`s free energy of hydration, {Delta}G. {Delta}G is a parameter which represents the sum of influences on durability of the various glass oxide components. A generalized relationship between these two variables is documented in [2]. This relationship appears to underpredict releases for glasses in the so-called ``Purex`` range of compositions which comprises a ...

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. This report presents measurements of mass transfer rates for the mixing of water and butanol in two-layer, TBP-aqueous mixtures, where the top layer is primarily TBP and ...

Energy Technology Data Exchange (ETDEWEB)

A solid electrolyte for lithium batteries requires several properties: a good ionic conductivity of about 10{sup -3} S/cm at 298 deg. K, a high cationic transport number (greater than 0.5), a redox stability window higher than 4.5 V, a good stability of the interface with the lithium electrode, and a sufficient mechanical stability. The family of gelled or hybrid electrolytes seems to meet all these requirements. Thus, a systematic study of the gelling of an ethylene carbonate and lithium bistrifluorosulfonimide (LiTFSI) based electrolyte has been carried out. The polymers used for gel or pseudo-gel synthesis are POE, PMMA and PAN which represent 3 different cases of interaction with the electrolyte. All the properties mentioned above have been studied according to the nature of the polymer and to the concentration of lithium salt, showing the advantages and drawbacks of each polymer. The possibility of using some of these gels in lithium-ion ...

Energy Technology Data Exchange (ETDEWEB)

Advanced lithium batteries presently under development operate either at the high temperatures associated with the LiCl-KCl molten salt (350-450/degree/C), or at ambient temperatures employing organic solvent based electrolytes. An intermediate temperature lithium battery is proposed as an alternative if it reduces corrosion problems present at high temperatures and improved kinetic performance with respect to ambient temperature cells. 17 refs.

Energy Technology Data Exchange (ETDEWEB)

A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with an anion such as a dihydrogen phosphate anion or a dihydrogen phosphite anion and additionally with an ammonium salt other than a salt of an inorganic acid of phosphorus. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.

Science.gov (United States)

The phytomanagement of Se-polluted soil and water is one strategy that may be environmentally sustainable and cost-effective for soils and waters enriched with natural-occurring Se. Several plant species, including Indian mustard (Brassica juncea), pickleweed (Salicornia bigelovii), and other salt/S...

Energy Technology Data Exchange (ETDEWEB)

Molten salt oxidation (MSO) is proposed as a {sup 238}Pu waste treatment technology that should be developed for volume reduction and recovery of {sup 238}Pu and as an alternative to the transport and permanent disposal of {sup 238}Pu waste to the WIPP repository. In MSO technology, molten sodium carbonate salt at 800--900 C in a reaction vessel acts as a reaction media for wastes. The waste material is destroyed when injected into the molten salt, creating harmless carbon dioxide and steam and a small amount of ash in the spent salt. The spent salt can be treated using aqueous separation methods to reuse the salt and to recover 99.9% of the precious {sup 238}Pu that was in the waste. Tests of MSO technology have shown that the volume of combustible TRU waste can be reduced by a factor of at least twenty. Using this factor the present inventory of 574 TRU drums ...

International Nuclear Information System (INIS)

Interfacial tension in the system toluene solution of di-2-ethylhexylphosphoric acid HDEHP-aqueous solutions of inorganic salts has been measured by the drop volume method. The ion-exchange constants in the monolayers formed by HDEHP and alkaline-earth metals have been measured.

Energy Technology Data Exchange (ETDEWEB)

When Silk fibre derived from Bombyx mori, a native biopolymer, was dissolved in highly concentrated neutral salts such as CaCl{sub 2}, the regenerated liquid silk, a gradually degraded peptide mixture of silk fibroin, could be obtained. The silk fibroin nanoparticles were prepared rapidly from the liquid silk by using water-miscible protonic and polar aprotonic organic solvents. The nanoparticles are insoluble but well dispersed and stable in aqueous solution and are globular particles with a range of 35-125 nm in diameter by means of TEM, SEM, AFM and laser sizer. Over one half of the {epsilon}-amino groups exist around the protein nanoparticles by using a trinitrobenzenesulfonic acid (TNBS) method. Raman spectra shows the tyrosine residues on the surface of the globules are more exposed than those on native silk fibers. The crystalline polymorph and conformation transition of the silk nanoparticles from random-coil and {alpha}-helix form ...

Energy Technology Data Exchange (ETDEWEB)

This report provides an overview of the scope and status of the US Department of Energy (DOE`s) Salt Repository Project (SRP) at the time when the project was terminated by the Nuclear Waste Policy Amendments Act of 1987. The report reviews the 10-year program of siting a geologic repository for high-level nuclear waste in rock salt formations. Its purpose is to aid persons interested in the information developed during the course of this effort. Each area is briefly described and the major items of information are noted. This report, the three salt Environmental Assessments, and the Site Characterization Plan are the suggested starting points for any search of the literature and information developed by the program participants. Prior to termination, DOE was preparing to characterize three candidate sites for the first mined geologic repository for the permanent disposal of high-level nuclear waste. The sites were in ...

International Nuclear Information System (INIS)

Four very common long term mineralogical changes in salt formations are discussed in the view of the safety considerations for underground repositories. Two of these processes, the 'Hartsalz' and 'Carnallite' dissolution were studied in two scale in situ experiments. The results are presented and compared with the results of the geochemical modelling with the computer code EQ3/6. Furthermore the reactions leading to the formation of the gypsum cap rock on the top of the Zechstein salt formations and to the polyhalitization of anhydrite are discussed. Geological field observations and mineral assemblages agree well with the results of the geochemical modelling employing the Pitzer formalism along with the Harvie, Moller and Weare database. We conclude that once the mechanisms of the chemical reactions are well understood it becomes possible to evaluate realistically whether such processes, when encountered in the repository, are still active or ...

International Nuclear Information System (INIS)

We devised a three-dimensional method for estimation of cerebral development and myelination which measures cerebral volume using MRI. Accuracy of the system was estimated using cadaver brains. The mean percentage error in the calculated volumes compared with the real volumes was 2.33 %, range 0.00-5.33 %. We applied the method to the volume of both cerebral hemispheres (CH), basal ganglia, thalamus and internal capsule (BT), and myelinated white matter (WM) in 44 neurologically normal individuals (4 months to 28 years of age), 13 patients with spastic motor disturbances (2-25 years of age), and 9 patients with athetotic motor disturbances (2-23 years of age). In the neurologically normal cases, the volumes of CH, BT and WM increased with age; the volume of MW more slowly than that of CH. In cases with spastic motor disturbances, the volumes of CH, BT and WM were between -1.4 and 3.5 SD, -1.0 and -3.5 SD, and 0.0 and -5.2 ...

International Nuclear Information System (INIS)

The results of interstitial brachytherapy in 13 patients with malignant brain tumors (malignant glioma 9 cases, metastatic brain tumor 4 cases) were reported. In all patients, Ir-192 thin wires were implanted temporarily in afterloading catheters, which were implanted appropriately by means of MRI or CT guided stereotactic technique. Clinical results on CT scan were as follows: CR (complete response) 1 case, PR (partial response) 6 cases and NC (no change) 6 cases. Even in the NC group, tumor growth was inhibited temporarily. Tumor free intervals were ranged 2-17 months. In early series, the intervals were about 2 months due to incomplete arrangement of radioactive implants. In recent series, prolongation of tumor free interval more than 12 months was achieved due to precise arrangements of implants. MRI guided stereotactic interstitial brachytherapy may provide ...

Energy Technology Data Exchange (ETDEWEB)

It has often been proposed that track diameter in etched detectors can be used for energy spectrometry. To test this proposition, the relationship between track diameter and energy of alpha particles, in the range 0.1-5.5 MeV, incident on CR-39 was studied. Two sets of detectors were irradiated by a collimated normally-incident beam of {alpha}-particles of different energies, using an Am-241 source. Different foils of the first set were etched for variable lengths of time in such a way that, in each case, the etchant reached the end of the latent track. Foils in the second set were etched for a fixed 'short' time of 2 h, for all {alpha}-energies. The linear rate of energy loss as well as the residual range of {alpha}-particles was determined by using Henke and Benton's computer program. It is found that, for 'short' etching times, the track diameter mimics the 'Bragg ...

International Nuclear Information System (INIS)

Large quantities of organic chemicals used in reprocessing spent nuclear-fuels at the Hanford Site have accumulated in underground high-level radioactive waste tanks. The organic content of these tanks must he known so that the potential for hazardous reactions between organic components and sodium nitrate/nitrite salts in the waste can he evaluated. The solubilities of organic compounds described in this report will help determine if they are present in the solid phases (salt cake and sludges) as well as the liquid phase (interstitial liquor/supernate) in the tanks. The solubilities of five significant sodium salts of carboxylic acids and aminocarboxylic acids [sodium oxalate, formate, citrate, nitrilotriacetate (NTA) and ethylendiaminetetraacetate (EDTA)] were measured in a simulated supernate solution at 25 degrees C, 30 degrees C, 40 degrees C, and 50 degrees C.

Energy Technology Data Exchange (ETDEWEB)

The crystal structure of Ca{sub 2}RuD{sub 6} has been determined by neutron powder diffraction: space group Fm3m, K{sub 2}PtCl{sub 6} structure, as found for other hexahydride salts of group 8 metals with alkaline earth or lanthanide counter ions. No structural phase transition was observed between 340 K and 50 K. The deuterium nuclear quadrupole coupling constant, 54.7 kHz, leads to an ionic character of the Ru-D bond of 76%. The known trends in the behaviour of A{sub 2}MH{sub 6} salts are interpreted in terms of the ionization energies of the cation and the central metal atom.

British Library Electronic Table of Contents (United Kingdom)

Spherical nano-sized YSZ (yttria stabilized ZrO2) powders were successfully synthesized via a reverse microemulsion system. The water droplets in the microemulsion system of yclohexane/water/span85/Triton X-100/hexyl alcohol can act as the nano-reactors which solubilize zirconium oxychloride and ammonia water separately. The minute original reactors are favor to the formation of nano-sized spherical YSZ powders and the dispersibility of the powders can be controlled effectually by adjusting the weight ratio of the LiNO3 molten salt to the precursor. The phase transformation from cubic to monoclinic starts at and 500??C and finally monoclinic and cubic phase with increased crytallinity coexist at 800??C. The effect of LiNO3 molten salt in the formation of YSZ powders was also discussed.

International Nuclear Information System (INIS)

High-temperature LiCl-KCl molten salt medium provides an efficient way to produce the paramagnetic Eu(II) ion to be magnetically diluted into a diamagnetic host medium. Eu(II) was formed by a dissolution and an auto-reduction processes in a high-temperature LiCl-KCl eutectic melt at 723 K by using Eu_2O_3 as a starting material. By using EPR and luminescence spectroscopic method, we studied the nature of the magnetically isolated paramagnetic Eu(II) ion diluted in a LiCl-KCl medium. With the aid of these spectroscopic tools, it was found that stable Eu(II) species was formed spontaneously at 723 K under anaerobic conditions. EPR and luminescence spectroscopy provided detailed information regarding the nature of the europium ion in a molten salt.

Energy Technology Data Exchange (ETDEWEB)

Decontamination and decommission activities related to the Molten Salt Reactor Experiment (MSRE) involve the trapping and recovery of radiolitically generated uranium hexafluoride and fluorine. Although fission product radiolysis was known to generate F{sub 2}, the formation of UF{sub 6} and its transport from the fuel salt was unexpected. Some of these gaseous radiolysis products have been moving through the gas piping to a charcoal bed since the reactor was shut down in 1969. Current and planned remediation and clean-up activities involve the trapping of the gaseous products, deactivation and treatment of the activated charcoal bed, stabilization and reconditioning of the fuel salt, and recovery of the uranium. The chemical aspects of these processes, including radiolytic generation mechanisms, reactions between uranium hexafluoride and fluorine and trapping materials such as activated charcoal, activated alumina, and ...

Energy Technology Data Exchange (ETDEWEB)

Thermal and mechanical properties for geothermal formations are tabulated for a range of temperatures and stress conditions. Data was obtained from the technical literature and direct contacts with industry. Thermal properties include heat capacity, conductivity, and diffusivity. Undisturbed geothermal profiles are also presented. Mechanical properties include Youngs modulus and Poisson ratio. GEOTEMP thermal simulations of drilling, production and injection are reported for two geothermal regions, the hot dry rock area near Los Alamos and the East Mesa field in the Imperial Valley. Actual drilling, production, and injection histories are simulated. Results are documented in the form of printed GEOTEMP output and plots of temperatures versus depth, radius, and time. Discussion and interpretation of the results are presented for drilling and well completion design to determine: wellbore temperatures during drilling as a function of depth; bit temperatures over the ...

Energy Technology Data Exchange (ETDEWEB)

Cryogenic distillation is the main industrial method for separating hydrogen's isotopes, because it presents the advantage of high separating factors and also the possibility of processing great quantities of gases. In the case of multicomponent mixtures the determination of transport for molecular species between the two phases is very difficult owing to the particularities of physical characteristics of each component from the mixture. The transport of molecular species is also strongly influenced by the hydrodynamics of two phases, in strong connection with the dimension of the interface between the vapor and liquid phase. The characteristics of the interface depend on the type and geometry of the separation area: plates or package. The traditional methods of analysis for exchange processes use the concept 'theoretic plate', a physical entity for which the values of concentrations for vapors and liquid that leaves the plate are in ...

International Nuclear Information System (INIS)

A mixture of crushed rock and bentonite is being considered as backfill and sealant for high-level nuclear waste repositories. Many variables affect the hydraulic conductivity of such a mixture, including the size and shape of the rock particles, method of mixing, water content and density of the clay, and the weight ratio of rock to clay. Mixtures of crushed basalt and bentonite have been tested to determine the relative effects of these variables. Two types of permeameters are used, 20 cm diameter stainless steel permeameters and 10 cm diameter clear PVC permeameters. Plugs are installed as a single lift or in many lifts; the water content of the clay ranged from air-dry (in most cases) to as high as 200%. Preliminary results show that a mixture of 75% crushed basalt and 25% bentonite has a hydraulic conductivity between 1 x 10/sup -9/ cm/s and 2.5 x 10/sup -8/ cm/s. In some cases, preferential flow paths have developed ...

Energy Technology Data Exchange (ETDEWEB)

Phenomena associated with induced currents and voltages on high voltage transmission lines were discussed. Basic principles were reviewed. Action taken by Hydro-Quebec to assess the importance of associated problems on its grid was described. Hydro-Quebec`s findings and recommendations were compared with those of the International Standard, IEC 1129. It was concluded that for most cases, induced currents and voltages were higher than those listed under Class A recommendations of IEC 1129 as rated switching capabilities for ground switches assigned to this duty. For worst case scenarios, it was also found that, values of induced currents and voltages were lower than those of Class B recommendations. Hydro-Quebec and GEC Alsthom T and D collaborated to design and type test a full range of low cost and efficient ground interrupter switches tailored to Hydro-Quebec`s needs. A list of general application criteria of ground ...

International Nuclear Information System (INIS)

High concentrations of self-interstitials are trapped by dopant atoms during ion implantation into Si. For group V dopants, these complexes are sufficiently stable to survive solid-phase-epitaxial (SPE) growth but break up on subsequent thermal processing and cause a transient-enhanced diffusion. Dopant diffusion coefficients are enhanced by up to five orders of magnitude over tracer values and are characterized by an activation energy of approximately one half of the tracer values. In the case of group III dopants, any complexes formed during implantation do not survive SPE growth but a second source of self-interstitials becomes significant and leads to similar transient effects. This is the damaged layer underlying the original amorphous/crystalline interface. These observations provide direct evidence for long-range self-interstitial migration in Si, and we believe these are the first observations of the interstitialcy diffusion mechanism ...

Energy Technology Data Exchange (ETDEWEB)

Live cores were obtained from five reservoirs using special precautions to prevent contamination by exogenous microorganisms and minimize exposure to oxygen. The depths from which the cores were obtained ranged from 2,705 ft to 6,568 ft. Core plugs were cut radially from live cores, encased in heat-shrink plastic tubes, placed in core holders, and fitted with inlets and outlets. Nutrient additions stimulated the in-situ microbial population to increase, dissolve stratal material, produce gases, and release oil. Reduction in flow through the core plugs was observed in some cases, while in other cases flow was increased, probably due to the dissolution of carbonates in the formation. A field demonstration of the ability of the in-situ microbial population to increase oil recovery by blocking the more permeable zones of the reservoir is currently underway. This demonstration is being conducted in the North Blowhorn Creek Unit ...

CERN Document Server

We model the transport of cosmic ray nuclei in the Galaxy by means of a new numerical code. Differently from previous numerical models we account for a generic spatial distribution of the diffusion coefficient. We found that in the case of radially uniform diffusion, the main secondary/primary ratios (B/C, N/O and sub-Fe/Fe) and the modulated antiproton spectrum match consistently the available observations. Convection and re-acceleration do not seem to be required in the energy range we consider: $1 \\le E \\le 10^3$ GeV/nucleon. We generalize these results accounting for radial dependence of the diffusion coefficient, which is assumed to trace that of supernova remnants. While this does not affect the prediction of secondary/primary ratios, the simulated longitude profile of the diffuse $\\gamma$-ray emission is significantly different from the uniform case and may agree with EGRET measurements without invoking {\\it ad ...

Energy Technology Data Exchange (ETDEWEB)

An in situ synthesis of ZnS and CdS quantum dots (QDs) in an aqueous solution of sodium hyaluronate (Hyal) produced foils emitting light on excitation with a UV light. The wavelength of emission was only slightly QDs size and more QDs concentration dependent and reached up to {approx}320 nm in the case of ZnS and {approx}400-450 nm in the case of CdS. Nanoparticles remained as non-agglomerated 10-20 nm nanoclusters. CdS/Hyal and ZnS/Hyal-QDs biocomposites were characterized using photoluminescence (PL), IR spectrometric techniques, and Transmission Electron Microscopy (TEM). The absolute molecular weights, radii of gyration, R{sub g}, and thermodynamic properties of the obtained foils are given. Electric resistivity studies performed for the hyaluronic foil in the 100-1000 V range have revealed that the hyaluronate foil has very weak conducting properties and QDs only insignificantly affect those properties as QDs ...

Energy Technology Data Exchange (ETDEWEB)

This report presents findings from the first year of a two-year study of interactive efforts involving utilities and non-utility parties (NUPS) working together to prepare plans, develop Demand-Side Management (DSM) programs, or otherwise promote integrated planning and the use of cost-effective DSM measures. Of the ten cases covered in the current study, seven involved the collaborative approach to NUP involvement, which generally is marked by intensive utility-NUP interactions designed to reach consensus on a broad range of important issues; in collaboratives, outside consultants often are provided to enhance the technical capabilities of the NUPS. Another of the cases in this study involved a cooperative arrangement,'' whereby a utility and a NLT worked together in a focused short-term effort to develop a single DSM program. The intense interaction involved in this approach makes it very similar to a ...

International Nuclear Information System (INIS)

Mycobacterium xenopi is one of the most common agents responsible for nontubercolar mycobacterial pulmonary disease on AIDS patients. These lesions have been studied with conventional radiography while CT has been used in patients with a specific mycobacterioses or non-AIDS pulmonary conditions from Mycobacterium xenopi. 12 AIDS patients were examined. They had pulmonary lesions from Mycobacterium xenopi, patients age ranged 30 to 46 years. All patients had CD4 blood levels lower than 250 cells/mL and Mycobacterium xenopi in the sputum. All patients underwent a standard chest radiograph and a CT examination. CT images were evaluated by three radiologists independently and the definitive diagnosis was made in the presence of a fourth radiologist. Chest CT showed parenchymal consolidation in 66% of cases, associated with bilateral basal bands in 16% of cases. Consolidation was unilateral in 41% of cases ...

International Nuclear Information System (INIS)

Metastable austenitic steels show excellent mechanical properties, such as high strength combined with excellent ductility and toughness due to martensitic transformation under mechanical loading (transformation induced plasticity effect). A good energy consumption, and, in the case of high-alloyed metastable austenitic steels, a high corrosion resistance, increase the potential of these materials for diverse applications, also in regard of safety requirements. Up to now, numerous wrought alloys were investigated concerning mechanical behaviour, TRIP-effect, martensitic transformation behaviour and modelling of transformation kinetics or stress-strain behaviour. New high alloyed cast CrMnNi-steels, developed at Technical University Bergakademie Freiberg, provide the chance to reduce processing steps, production time and costs. In order to understand the influence of temperature on the martensitic phase transformation behaviour and therefore on mechanical properties ...

Energy Technology Data Exchange (ETDEWEB)

Simultaneous nitriding and ageing heat treatments of precipitation hardenable tool steel was carried out inside a DC-pulsed plasma nitriding reactor. A single heat treatment cycle was done, as the plasma nitriding and age hardening processes occur approximately at the same ranges of temperatures and times. Specimens of Cr-Ni-Mo-Al age hardenable steel, in the solubilized and solubilized and aged conditions, were tested. Plasma nitriding and ageing, carried out at 500 deg. C for times ranging between 2 and 8 h, increased the surface hardness up to 1000 HV, producing case depths between 100 and 200 {mu}m. The core hardness of solubilized samples increased from 30 to 39 Rockwell C after the plasma nitriding treatment proving the possibility of nitriding and ageing at the same treatment cycle. The pre-aged samples did not show any overageing after the simultaneous plasma nitriding and ageing treatments. The corrosion resistance ...

International Nuclear Information System (INIS)

From the indoor radon problem arises a great challenge for the radiation protection of the population. The soil can be considered as the only source for high radon concentrations in buildings. The contribution of common building materials to high indoor concentrations with a range of 30 Bq/m"3 is negligible low. Therefore building materials for radon mitigation should be judged by their tightness against diffusive radon and not by their radon exhalation rate. Also isolation materials for mitigation should be radon tight. The radon diffusion coefficient describes the physical processes in relatively homogeneous samples. The diffusion coefficient D and the diffusion length R are very exactly determined by a self engineered measuring method. The range of D reaches from D = (0.0005 to 2.35) . 10"-"6 m"2/s for building materials and from D = (0.07 to < 10"-"6) . 10"-"6 m"2/s for isolation materials. Applicable mitigation measures like increased ...

International Nuclear Information System (INIS)

In the Harghita volcanic range (Romania) there are many occurrences of dry CO2 emanations, called mofettes. The emanating gas with high carbon dioxide content has a proved curative effect. The gas also contains important quantities of radon. Since the mofettes are used in curative purposes in several illnesses, in most of the cases without medical supervising, has been proposed to determine the radon activity concentration in some of the most frequented mofettes from Romania. The seasonal variations have also been monitored and were calculated the effective doses received by the patients during a cure. The radon activity concentrations' levels above the mofettes indoor air range between 548 and 10 717 Bq/m3 while within the gas pools' values between 3210 and 32 781 Bq/m3 have been measured. The effective dose received by the patients during a cure is between 0.0086 and 0.16 mSv. No major seasonal variations of the radon ...

Energy Technology Data Exchange (ETDEWEB)

Numerical studies are performed to identify an optimal range of geometric parameters in connection with the design of an impingement-conditioned small direct-injection diesel engine. The parametric studies were made in a pressure chamber with a circular protrusion on to which sprays are directed to impinge. Computational runs were made for 24 cases carefully chosen to allow examination of the effects on post-impingement spray characteristics of the following parameters: (a) the nozzle-plate distance and (b) the size and geometry pattern of the protrusion. An optimal range of these parameters has been identified through an analysis of the calculated results in terms of vapour concentration, the Sauter mean diameter of the wall spray and the dispersed wall spray volume. The results obtained also reveals that, by just changing the size of the impingement surface and the impingement distance, local fuel vaporization efficiency ...

International Nuclear Information System (INIS)

The effects of neutron irradiation on the superconducting and normal state properties of alloys and compounds are presented. Particular emphasis is placed on the A-15 compounds where the effects of neutron irradiation on Tsub(c), Hsub(c_2), long range order parameter and lattice parameter are described. Large depressions (up to 80%) in Tsub(c) are observed for all the A-15 compounds studied with the exception of Mo_3Os where much smaller decreases in Tsub(c) are seen. Along with the decrease in Tsub(c) and increase in lattice parameter, the degree of long range order, as measured by X-ray and neutron diffraction, decreases. Also presented are the results of isothermal and isochronal anneals up to 900"0C. The unirradiated value of Tsub(c) can be restored by annealing, and for those systems where measurements have been made, recovery of the lattice parameter and order parameter also takes place. The effects observed in irradiated material, ...

International Nuclear Information System (INIS)

The EUROTRAC sub-project ''Tropospheric Ozone Research'' (TOR) follows a dual strategy: - Observation of the chemical processes contributing to the oxygen balance directly in the atmosphere; - Establishment of a validated data base for model calculations. Both tasks require simultaneous measurements of a wide range of chemical and meteorological components. In the case of the investigation of the chemical processes, it is also desirable to measure the free radicals directly involved in ozone production. In the project described, a measuring station was set up. For a period of two years and a half, continuous measurements were made of ozone and its chemical precursors (NO, NO_2, NO_y, VOC, CO), as well as other photooxidants (H_2O_2 and organic hydroperoxides, organic nitrates), the photolysis frequency of NO_2, and meteorological parameters (wind, temperature, moisture, aerosols). The station was located on the Schauinsland mountain in the ...

Energy Technology Data Exchange (ETDEWEB)

The usually low wear resistance of titanium materials can be increased by the thermochemical surface treatment nitriding. In result of comparative investigations of gas and plasma nitriding it will be shown that it is possible to obtain a specific variation of the properties in the highly stressed case by means of these both technologies on example of the ({alpha}+{beta}) alloy Ti-6Al-4V. Gas and plasma nitriding was carried out in the temperature range from 650 to 800 C over 4 to 48 h in different gas atmospheres, i.e. 100% NH{sub 3} (gas), 100% N{sub 2} (gas and plasma), 20% H{sub 2} + 80% N{sub 2} and 20% Ar + 20% H{sub 2} (plasma). The temperature range was fixed in the middle of ({alpha}+{beta}) region, because the core properties are influenced negative in the field of {beta}-transustemperature. The relations between the applied nitriding technologies, the layer structure (chemical, phases, geometrical) and selected ...

Energy Technology Data Exchange (ETDEWEB)

To develop the automatized crane and to apply the relevant technology to nuclear power plants, in this project and automatized crane control system is developed along with a swing and shock crane. Also, this technology has been transferred to Bando Machinery Co. Ltd. The drive mechanism of crane is designed by adopting vector drives which provide soft acceleration and deceleration characteristics. Also, radio modems and a long-range laser displacement sensor which are commercially available are introduced to accommodate the large scaled crane systems. Also, several devices are developed for the automation of crane system. These are a crane controller, a supervisory controller, a angle measuring device, and laser localizer, a drum grapple device, and crane supervisory program. The performance of developed crane system is revealed to rapidly reduce the residual swingof the transported object and precisely controls the object position in any case. ...

Energy Technology Data Exchange (ETDEWEB)

Radionuclide X-ray fluorescence analysis (RXRFA), as a non-destructive method, relatively simple and allowing measurements to be carried out in situ, is an excellent tool in research on various objects of art. A range of artefacts have been investigated by our laboratory, in part for the purposes of history of art and in part as a basis for restoration works - medieval frescoes in some Czech castles and churches, metal sculptures and objects of applied art, paints and inks of old manuscripts, paintings. Some of these are among the most valuable monuments in the Czech cultural heritage. The contribution of the results of the tests to the investigation of their 'life story' and, in some cases, to their conservation, is not negligible. Later additions and repairs can be recognised, and materials and technologies that are close to their historic counterparts can be used in restoration work.

CERN Document Server

Increasingly, business projects are ephemeral. New Business Intelligence tools must support ad-lib data sources and quick perusal. Meanwhile, tag clouds are a popular community-driven visualization technique. Hence, we investigate tag-cloud views with support for OLAP operations such as roll-ups, slices, dices, clustering, and drill-downs. As a case study, we implemented an application where users can upload data and immediately navigate through its ad hoc dimensions. To support social networking, views can be easily shared and embedded in other Web sites. Algorithmically, our tag-cloud views are approximate range top-k queries over spontaneous data cubes. We present experimental evidence that iceberg cuboids provide adequate online approximations. We benchmark several browser-oblivious tag-cloud layout optimizations.

Energy Technology Data Exchange (ETDEWEB)

Although incompressible fluid flows can be regarded as a particular case of a general problem, numerical methods and the mathematical formulation aimed to solve compressible and incompressible flows have their own peculiarities, in such a way, that it is generally not possible to attain both regimes with a single approach. In this work, we start from a typically compressible formulation, slightly modified to make use of pressure variables and, through augmenting the stabilising parameters, we end up with a simplified model which is able to deal with a wide range of flow regimes, from supersonic to low speed gas flows. The resulting methodology is flexible enough to allow for the simulation of liquid flows as well. Examples using conservative and pressure variables are shown and the results are compared to those published in the literature, in order to validate the method. (author)

International Nuclear Information System (INIS)

The energy dependence of the Yb and Au L_#alpha#/L_l X-ray intensity ratio, produced by 0.5 - 3.0 MeV/u Li, Be, C, N, F, and Si ion bombardment (Malhi and Gray, Phys. Rev. A 44, 7199, (1991)), measured at 90"0 relative to the beam axis, has been explained. While for light ion impact the behaviour of the alignment parameter as a function of impact velocity is dominant, for the impact of heavier ions the multiple ionization effects become important. Using Larkins' prescription in the last case, calculations have been performed, which agree well with the data over the whole energy range investigated. (Author).

CERN Document Server

Spatial Fluorescence Cross Correlation Spectroscopy is a rarely investigated version of Fluorescence Correlation Spectroscopy, in which the fluorescence signals from differ-ent observation volumes are cross-correlated. In the reported experiments, two observation volumes, typically shifted by a few $\\mu$m, are produced, with a Spatial Light Modulator and two adjustable pinholes. We illustrated the feasibility and potentiality of this technique by: i) measuring molecular flows, in the range 0.2 - 1.5 $\\mu$m/ms, of solutions seeded with fluorescent nanobeads or rhodamine molecules (simulating active transport phenomenons); ii) investigating the perme-ability of phospholipidic membrane of Giant Unilamellar Vesicles versus hydrophilic or hydrophobic molecules (in that case the laser spots were set on both sides of the mem-brane). Theoretical descriptions are proposed together with a discussion about FCS based, alternative methods.

International Nuclear Information System (INIS)

A novel system for real-time radiation monitoring in reactor or accelerator facilities has been studied using an imaging plate. The authors made a feasibility study on a new neutron detection system using both photostimulated luminescence (PSL) and prompt luminescence (PL) generated in a neutron imaging plate (NIP) when the NIP is irradiated by neutrons. A readout system consisting of a semiconductor laser and a photomultiplier tube was fabricated for the purpose. It was confirmed that the system can measure both PSL and PL, where Am-Li was used as a neutron source. It may be possible to establish a new wide-range neutron monitoring system using the developed system as a PL mode normally, and as a PSL mode in case of intense neutron dose that cannot be measured in a PL mode because of saturation of the detection system. (author)

International Nuclear Information System (INIS)

The disrupted magnetic braking theory for the period gap of cataclysmic variable systems is used to study the binary evolution of low-mass main-sequence-like stars with white dwarf companions. The model is able to reproduce the observed location and width of the gap provided that the average mass transfer rates above the upper edge of the gap are greater than about 1.9 x 10 to the -9th solar masses/yr. For the case of angular momentum loss by magnetic braking, the slope of the mass transfer rate with respect to orbital period is shown to range from 3.4 to 3.7. For the evolutionary sequences considered, the He-3 abundance at the surface of the secondary exceeds 0.0015 after the complete mixing phase, resulting in modifications in the nuclear burning development of nova explosions. 31 refs.

CERN Document Server

In the paper we investigate a mathematical model describing the growth of tumor in the presence of immune response of a host organism. The dynamics of tumour and immune cells is based on the generic Michaelis-Menten kinetics describing interaction and competition between the tumour and the immune system. The appropriate phenomenological equation modeling cell-mediated immune surveillance against cancer is of the predator-prey form and within a given choice of parameters exhibits bistability. Under the influence of spontaneous weak fluctuations, the model may be analyzed in terms of a stochastic differential equation bearing the form of an overdamped Langevin-like dynamics in the external quasi-potential represented by a double well. We analyze properties of the system within the range of parameters for which the potential wells are of the same depth and when the additional perturbation describing a periodic treatment is insufficient to overcome the barrier height ...

International Nuclear Information System (INIS)

High purity Fe-50mass%Cr alloys containing (C+N) in the range of 30 to 500 mass ppm were prepared and their corrosion resistance was investigated. Pitting potential in a 3.5mass%NaCl solution at 343K rose with reducing (C+N) content. Alloys containing (C+N) at less than 100 mass ppm did not sustain pitting corrosion. However, alloys containing 500 mass ppm (C+N) corroded severely in 6%FeCl_3+1/20N HCl solutions. Heat treatment at 923K was recognized as influencing corrosion resistance due to precipitation of carbonitrides only in the case of the alloy containing 500 mass ppm (C+N). (orig.).

Energy Technology Data Exchange (ETDEWEB)

Wood plastic composite (WPC) of kadom, simul, mango and debdaro were prepared with two monomers methylmethacrylate (MMA) and butylmethacrylate (BMA) using high energy ionizing radiation. X-ray diffraction and scanning electron microscope (SEM) studies reveal that significant grafting occurred with wood fiber. Electric properties like resistivity and dielectric constant of both wood and WPC were measured under different moisture contents and relative humidities. The resistivities of wood decreased dramatically with increase of moisture content, but those of WPC decreased very slowly with moisture content. The dielectric constant of wood increased significantly with moisture content but no significant difference was observed in the case of WPC within the range of moisture contents studied. The dielectric constants of untreated wood also increased with their densities. (author).

Energy Technology Data Exchange (ETDEWEB)

One of the technical options being considered for long term disposition of weapons grade plutonium is geologic storage at Yucca Mountain. Multikilogram quantities of plutonium are to be vitrified, placed within a heavy steel container, and buried in the material know as Nevada tuff. It has been postulated that after ten thousand years, geologic and chemical processes would have disintegrated the steel container and created the possibility for plutonium to form mixtures with Nevada tuff and water that could lead to a nuclear explosion in the range of kilotons. A survey and description of critical homogeneous mixtures of plutonium, silicon dioxide, Nevada tuff, and water which also identified the mixture regimes where autocatalytic dynamic behavior is possible was completed. This study is a follow up of this survey and the major objective is to examine the dynamic behavior of the worst case critical and supercritical configurations of plutonium, ...

Energy Technology Data Exchange (ETDEWEB)

In this paper the concept of a composite power system stabilizer is investigated. This stabilizer comprises a properly designed, robust, conventional power system stabilizer (CPSS) and an auxiliary stabilizer (AS) which can be either a self-tuning stabilizer (ASTS) or a fixed-parameter stabilizer (AFPS). For small disturbances, the CPSS performs satisfactorily over a wide range of operating conditions. When large disturbances occur the auxiliary stabilizer augments the performance of the CPSS. It has been demonstrated that the composite power system stabilizer can significantly improve the dynamic performance of the system when there is a major disturbance such as a short circuit in the system. Because in the case of a single-machine system the parameters of the ASTS do not vary appreciably, it can also be implemented as a fixed-parameter device; this simplifies significantly the implementation of the composite PSS. (Author)

CERN Document Server

Increasingly, business projects are ephemeral. New Business Intelligence tools must support ad-lib data sources and quick perusal. Meanwhile, tag clouds are a popular community-driven visualization technique. Hence, we investigate tag-cloud views with support for OLAP operations such as roll-ups, slices, dices, clustering, and drill-downs. As a case study, we implemented an application where users can upload data and immediately navigate through its ad hoc dimensions. To support social networking, views can be easily shared and embedded in other Web sites. Algorithmically, our tag-cloud views are approximate range top-k queries over spontaneous data cubes. We present experimental evidence that iceberg cuboids provide adequate online approximations. We benchmark several browser-oblivious tag-cloud layout optimizations.

International Nuclear Information System (INIS)

Composite materials of synthetics (based on monomers, oligomers and thermoplastics) and of natural polymers (wood and other fibrous cellulosics) prepared by radiation processing, offer valuable structural materials with enhanced coupling forces between the components. The applied polymer chemistry of such composites shows several common features with that of radiation grafting, e.g. the polymerization rate of oligomer-monomer mixtures in wood remains in most cases proportional to the square-root of the initiating dose-rate, just as in the simultaneous grafting, demonstrating that the chain termination kinetics remain regularly bimolecular in the corresponding dose-rate ranges. In the processing experiences of such composites, low dose requirement, easy process-control, and good technical feasibility have been found for composites of wood with oligomer-monomer mixtures, for coconut fibres with unsaturated polyesters and for pretreated wood fibre ...

Energy Technology Data Exchange (ETDEWEB)

The application of the phased array technique was limited to heavy and thick wall components as present in the nuclear industry. With the improvement of the equipment and probes other application areas are now open for the phased array technique, e.g. the inspection of the turbine blade root, weld inspection in a wall thickness range between 12 and 40 mm, inspection of aircraft components, inspection of spot welds or inspection of concretes. The aim of the use of phased array techniques has not been changed related to the first applications, i.e. the adaptation of the sound beam to the geometry by steering the angel of incidence or the skewing angle as well as the focussing of sound fields. Due to the fact, that the new applications of the phased array techniques in some cases don't leave the laboratories for the time being, the examples of this contribution will focus applications with practical background. (orig.)

CERN Document Server

Mono-layers of stearic and behenic acids and mixtures of them in different proportions, deposited with the Langmuir-Blodgett technique, were used to study the alignment and the alignment dynamics in nematic liquid crystal cells. A relaxation process from a splay-bend flow induced metastable orientation to the homeotropic one occurs. The lifetime of the metastable state was found to depend on the mono-layer composition. The transition between the homeotropic and the conical anchoring was found to be irreversible in the case of the mixed aligning mono-layers: on cooling from the isotropic phase a quasi-planar nematic state (schlieren texture) appears. It is stable in a range of a few degrees below the clearing point and, on decreasing the temperature, relaxes to the homeotropic state in form of expanding domains.

International Nuclear Information System (INIS)

Ultraveiolet spectroscopy of molecules in vapour phase gives valuable information about electronic structure of free molecules. But in many cases vaipour phase investigations are not possible and in order to isolate molecules within solid lattice, we used cryogenic temperature and high vacuum technology to study absorption spectrum within the spectral range (230-270)nm of an isolated benzene molecule in Argon, Krpton, Nitrogen, Carbon and methane matrices. The spectra shifts were measured and calculated in the matrix environment for the electronnic transition (B 24--A 19) in benzene molecule using the matrices mentioned above. Molar extinction coefficients and oscillator strength were measured too. (7 tabs., 32 figs., 50 refs.).

Energy Technology Data Exchange (ETDEWEB)

Results are presented of trials in W. Germany involving Populus tremula X P. tremuloides. In a nursery in late August - early September 1971, some 1300 buds from 38 selected 3-yr-old hybrid aspen seedlings were grafted into T-slits at nodes 10-20 cm above root' collars of 1 and a half yr-old hybrid aspen stock (products of controlled crossings, and in some cases of similar parentage to the transplanted buds). In spring 1972, each stock (from which its own buds were removed) was cut back to a 'peg' 15-20 cm above the level of the graft; the 'peg' was later used to support the new shoot developed from the transplanted bud. By Sept. 1972, 33% of grafts were successful, the success rate being significantly different (3-67%) within clones; average height of scion shoots ranged from 79 to 375 cm (no significant difference between clones). In spring 1973, some 190 grafts from 35 clones were row-planted in ...

Energy Technology Data Exchange (ETDEWEB)

Limited demand and high cost has prevented the construction of hard rock caverns in this country for a number of years. The storage of natural gas in mined caverns may prove technically feasible if the geology of the targeted market area is suitable; and economically feasible if the cost and convenience of service is competitive with alternative available storage methods for peak supply requirements. It is believed that mined cavern storage can provide the advantages of high delivery rates and multiple fill-withdrawal cycles in areas where salt cavern storage is not possible. In this research project, PB-KBB merged advanced mining technologies and gas refrigeration techniques to develop conceptual designs and cost estimates to demonstrate the commercialization potential of the storage of refrigerated natural gas in hard rock caverns. Five regions of the U.S.A. were studied for underground storage development and PB-KBB reviewed the literature to determine if the ...

Energy Technology Data Exchange (ETDEWEB)

Alpha continuous air monitors (CAMs) will be used at the Waste Isolation Pilot Plant (WIPP) to measure airborne transuranic radioactivity that might be present in air exhaust or in work-place areas. WIPP CAMs are important to health and safety because they are used to alert workers to airborne radioactivity, to actuate air-effluent filtration systems, and to detect airborne radioactivity so that the radioactivity can be confined in a limited area. In 1993, the Environmental Evaluation Group (EEG) reported that CAM operational performance was affected by salt aerosol, and subsequently, the WIPP CAM design and usage were modified. In this report, operational data and current theories on aerosol collection were reviewed to determine CAM quantitative performance limitations. Since 1993, the overall CAM performance appears to have improved, but anomalous alpha spectra are present when sampling-filter salt deposits are at normal to high levels. This ...

Science.gov (United States)

Describes laboratory and industrial tests on the use of lowasash sulphurous petroleum coke during reduction of barite. Shows the potential of substituting blast furnace coke with petroleum/coke fines in this process.

International Nuclear Information System (INIS)

Starting from the Molten Salt Breeder Reactor project of Oak-Ridge, we have performed parametric studies in terms of safety coefficients, reprocessing requirements and breeding capabilities. In the frame of this major re-evaluation of the molten salt reactor (MSR), we have developed a new concept called Molten Salt Fast Reactor or MSFR, based on the Thorium fuel cycle and a fast neutron spectrum. This concept has been selected for further studies by the MSR steering committee of the Generation IV International Forum in 2009. Our reactor's studies of the MSFR concept rely on numerical simulations making use of the MCNP neutron transport code coupled with a code for materials evolution which resolves the Bateman's equations giving the population of each nucleus inside each part of the reactor at each moment. Because of MSR's fundamental characteristics compared to classical solid-fuelled reactors, the classical Bateman ...

UK PubMed Central (United Kingdom)

OBJECTIVE--To examine the effect of a reduced sodium and increased potassium and magnesium intake on blood pressure. DESIGN--Randomised double blind placebo controlled trial. SETTING--General population...Full Text Available

UK PubMed Central (United Kingdom)

Rat somatotropin (growth hormone) was labelled biosynthetically by incubating anterior pituitary lobes with radioactive amino acids for 24 h in a simple buffered salts medium containing glucose. The...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The estimation of numerical values of the mean distance of closest approach of ions, a, of alkaline-earth metal ion salts in aqueous solutions, determined from activity coefficients, as well as from different theoretical approaches, is presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

For the development of high ionic conductive solid electrolyte, LiTi2(PO4)3 (LTP), one of the promising inorganic solid electrolyte, was synthesized to investigate an effect of additional lithium salt on the ion conductivity. Lithium salt added LTP composite electrolyte sintered at 900{degree}C exhibited highest conductivity, which was two order magnitude higher than pure LTP. Effects of lithium salt addition are as follows. Conductivity of the composite electrolyte provided larger sintering temperature dependence than the pure LTP. From X-ray diffraction analysis, structures and compositions were resemble between two composite electrolytes. Byproducts except LTP provided rather low conductivity. It was suggested that melted constitution in the composite can affect the sintering improvement by the additional lithium salt at temperatures over 800 {degree}C. From the observation of ruptured surface of ...

UK PubMed Central (United Kingdom)

Urmia Lake has been designated as an international park by the United Nations. The lake occupies a 5700 km2 depression in northwestern Iran. Thirteen permanent rivers flow into the lake. Water level...Full Text Available

UK PubMed Central (United Kingdom)

Previously we reported that standard oral rehydration salts (ORS) solution is not as effective as a reduced-osmolarity glucose-based ORS for the treatment of children with acute noncholera diarrhoea:...Full Text Available

UK PubMed Central (United Kingdom)

The objective of this experiment was to determine the effect of dietary grain on calcium homeostasis. Six rumen-fistulated dairy cows with 3 or more previous lactations and no history of parturient...Full Text Available

Science.gov (United States)

Results of feasibility experiments for determining the mineral content of individual stains on special Sensitized Paper are presented. The stains were formed on the paper by the impaction of laboratory generated salt water droplets. Of the techniques exam...

Science.gov (United States)

The perspectives, information and conclusions conveyed in research project abstracts, progress reports, final reports, journal abstracts and journal publications convey the viewpoints of the principal investigator and may not represent the views and policies of ORD and EPA. Concl...

International Nuclear Information System (INIS)

Until 1990, in Tuscany, salt pollution of anti-salt insulators installed on high-tension transmission lines had led to rare breakdowns. On the contrary, in the last months of 1990, in most of Tuscany, following a strong libeccio wind coming from the Tyrrhenian Sea, and due to a long period of drought, salt deposits accumulated on the insulators of the high-voltage transmission lines (380 kV, 220 kV and 132 kV). This phenomenon not only took place in the coastal areas near Livorno, Pisa and Grosseto, but also in areas far away from the sea such as Florence, Prato, Arezzo and Siena. Following this, several high-tension lines, and whole sections of 380 kV electric stations went out of order, damaging the stations' equipment, insulators on the lines, and in particular porcelain insulators. The maintenance operations that were immediately undertaken consisted in washing operations, first focussed on stations, and then on lines. ...

UK PubMed Central (United Kingdom)

A general procedure for stabilization of O2-labile enzymes exploiting "salting out" of oxygen from the microenvironment in the molecular layers immediately adjacent to charged surfaces of polyionic...Full Text Available

CERN Document Server

Single-case and Small-n Experimental Designs

Science.gov (United States)

... projectile. Descriptors : *Combustible cartridge cases, *Patents, Laminates, Ammunition propellants, Nitrocellulose. Subject ...

British Library Electronic Table of Contents (United Kingdom)

Solution and dilution enthalpies of aqueous solutions of potassium diclofenac salt (K_DC) were measured by an isoperibolic calorimeter at 298.15 and 318.5?K. Heat capacities of the solutions with concentrations 0.002?0.09?mol?kg?1 were obtained at the temperature interval of 288.15?318.15?K using a scanning adiabatic microcalorimeter. The virial coefficients were derived from Pitzer?s model, and the excess thermodynamic functions of both the solvent and the solute of the solution were calculated. The concentration and temperature dependencies of thermodynamic characteristics of the solution were analyzed and discussed.

International Nuclear Information System (INIS)

Crystallization points of aqueous solution of the systems M(ClO_4)_2-H_2O (M"2 = Mg"2"+, Ca"2"+, Sr"2"+, Ba"2"+), depending on the salt concentration, were identified by visual-polythermal method. Relying on model notions on the structure of the electrolyte solutions, specific features of strontium perchlorate solubility polytherm and concentration dependence of the relative dynamic viscosity of the salt aqueous solutions are discussed

International Nuclear Information System (INIS)

In PWR steam-generators, the crevice between tube and tube-support plate tends to fill with porous deposits during operation and acts as a concentration site for chemicals in the boiler water, which may lead to corrosion of the tube and tube-support-plate. The rate of concentration, the magnitude of the concentration factor and the rate of release of solute when conditions change are important parameters for devising strategies to minimize corrosion. Values of these parameters for salt concentration have therefore been measured in a laboratory simulation of the crevice and are used to formulate a model of the concentrating process.

Energy Technology Data Exchange (ETDEWEB)

Enzyme-linked Immunosorbent assay systems for the identification of irradiated egg, pork and chicken was developed. Eggs were irradiated in their shells to 0.5{approx}7kGy. Pork was irradiated to 0.5{approx}3kGy and chicken irradiated to 0.5kGy{approx}5kGy. The most sensitive proteins to irradiation were screened by SDS-PAGE and purified. Ovalbumin from egg, salt soluble protein(p) from pork, and salt soluble protein(c) from chicken showed the most sensitivity to irradiation. To investigate for a practical use in identifying of irradiated egg, pork and chicken, competitive ELISA was performed. The binding activity of ovalbumin to anti-ovalbumin IgG was reduced in a dose-dependent manner by irradiating up to 7kGy, and considerably lowered after irradiating at 7kGy. The concentration of 50% inhibition of ovalbumin to IgG was increased to 1.5(0.5kGy){approx}3.7(7kGy) times in an dose-dependent relationship. The binding activity of ...

Energy Technology Data Exchange (ETDEWEB)

For heavy-ion beam driven inertial fusion ''liquid-protected'' reactor designs such as HYLIFE-II, a mixture of molten salts made of F{sup 10}, Li{sup -6}, Li{sup 7} and Be{sup 9} (called flibe) allows small chambers and final-focus magnets closer to the target with superconducting coils suffering higher radiation damage, though they can stand only a certain amount of energy deposited before quenching. This work has been primarily focusing on verifying that total energy deposited by fusion neutrons and induced gamma rays remain under such limit values and the final purpose is the optimization of the shielding of the magnetic lens system from the points of view of the geometrical configuration and of the physical nature of the materials adopted. The system is analyzed in terms of six geometrical models going from simplified up to much more realistic representations of a system of 192 beam lines, each focused by six magnets. A 3-D ...

Energy Technology Data Exchange (ETDEWEB)

Waste is a heterogeneous fuel, often with high levels of chlorine, alkali and heavy metals. This leads to much more severe corrosion problems than combustion of fossil fuels. The corrosion rates of the materials used can be extremely high. Materials used for heat transferring parts are usually carbon steel or low alloyed steel. These are significantly cheaper than other steels. Austenitic stainless steel is also used, but is often avoided due to its sensitivity to stress corrosion cracking. More advanced materials, such as nickel base alloys, can be used in extremely aggressive environments. Since these materials are expensive and do not always have sufficient mechanical properties, they are often used as coatings on carbon steel tubes or as composite tubes. A new method, which shows good results at the first tests in plants, is electroplating with nickel. Plastic materials can be used in low temperature parts if the temperature does not exceed 150 deg C. A glass fibre inforced ...

International Nuclear Information System (INIS)

Ewing's sarcoma is the most common malignant bone tumour occurring in children and adolescents and exists in two different clinico pathological entities: osseous Ewing's sarcoma (OES) and extraosseous Ewing's sarcoma (EES). Five cases of primary epidural EES are described, which presented with non-specific symptoms leading to a long diagnostic delay. The median age at diagnosis was 22 years (range 13-36 years). The median diagnostic delay was 3 months. All patients had one or more neurological deficits. All underwent surgical exploration with a laminectomy and partial resection followed by adjuvant radiotherapy to a dose of 46-50 Gy and chemotherapy with VAC (vincristine, adriamycin and cyclophosphamide) alternating with ICE (ifosphamide, cisplatin and etoposide) for at least six cycles. The mean follow-up period is 21.2 months (range 11-32 months). Four of the five patients achieved a complete remission and are disease ...

International Nuclear Information System (INIS)

The present situation of the researches that have been made for predicting the process and range of diffusion of warm drain is reviewed. This review is divided into eight sections. The first section deals with the present situation of warm drain from power plants. For the establishment of drainage standard, there are many difficult problems to be solved because water temperature differs in its nature from other regulation items. In the second section, the process of diffusion and cooling of warm drain is explained. The third section deals with the diffusion characteristics of warm drain in Japanese coastal sea due to water temperature. Two types of diffusion are known. One is dominant irregular current, and the other is periodical reciprocating stream. The fourth section deals with the methods of prediction of diffusion. Research methods and simulation models are described. The fifth section deals with the prediction with single layer model. Fundamental ...

International Nuclear Information System (INIS)

The temperature dependences of the heat capacity of commercial titanium VT1-0 and alloys on its base, VT5 and VT5-1, have been derived in the temperature range of 4 to 290 K. For comparison, similar measurements have been conducted on pure titanium and specially prepared solid solutions on its base (Ti+3.7 at.% Al and Ti+0.82 at.% Sn). The measurement accuracy has been sufficient for comparing the results with calculation data. The obtained results are interpreted using the known concepts of the role of the mass of interstitial atoms and changes in the interatomic bond forces. It is shown that the phonon components of the molar heat capacities of solid solutions of Al in titanium have lower values in the entire temperature range, as compared to titanium. The corresponding differences are proportional to the Al concentrations. The lower molar heat capacity in the case of dissolution of Al is due to the low mass of the ...

International Nuclear Information System (INIS)

We have studied the application of direct aperture optimization (DAO) as an inverse planning tool for breast IMRT. Additionally, we have analysed the impact of respiratory motion on the quality of the delivered dose distribution. From this analysis, we have developed guidelines for balancing the desire for a high-quality optimized plan with the need to create a plan that will not degrade significantly in the presence of respiratory motion. For a DAO optimized breast IMRT plan, the tangential fields incorporate a flash field to cover the range of respiratory motion. The inverse planning algorithm then optimizes the shapes and weights of additional segments that are delivered in combination with the open fields. IMRT plans were generated using DAO with the relative weights of the open segments varied from 0% to 95%. To assess the impact of breathing motion, the dose distribution for the optimized IMRT plan was recalculated with the isocentre sampled from a predefined ...

International Nuclear Information System (INIS)

Due to thermal gradients and load changes steam-turbine casings suffer combined creep-fatigue loading. Creep and fatigue portions depend on service conditions. Special interest is focused on the behaviour of creep-fatigue cracks, originated from potential defects due to construction and manufacturing weldments, on residual lifetime assessment. The project deals with the crack-growth behaviour at 530deg C and r.t. of welded and unwelded heat-resistant cast steels: 1% CrMoV-cast (GS-17 CrMoV 5 11, two melts: low and high V-content) and 12% CrMoV-cast (G-X 22 CrMoV 12 1). The crack planes of CT-specimens investigated, taken from manual arc-welded plates, were situated in the heat-affected zone (HAZ). The fatigue, creep and combined creep-fatigue crack-growth behaviour was investigated by means of low-frequency (0.5 and 0.05 Hz) tests, holding-time (20 min) tests and constant load tests up to about 5 000 h. Metallographic investigations show that in the ...

ScienceCinema

...introduced english ...the range of simple english ...the range of simple english ...