Quantitative assessment of safety barrier performance in the prevention of domino scenarios triggered by fire

International Nuclear Information System (INIS)

Landucci, Gabriele; Argenti, Francesca; Tugnoli, Alessandro; Cozzani, Valerio

2015-01-01

The evolution of domino scenarios triggered by fire critically depends on the presence and the performance of safety barriers that may have the potential to prevent escalation, delaying or avoiding the heat-up of secondary targets. The aim of the present study is the quantitative assessment of safety barrier performance in preventing the escalation of fired domino scenarios. A LOPA (layer of protection analysis) based methodology, aimed at the definition and quantification of safety barrier performance in the prevention of escalation was developed. Data on the more common types of safety barriers were obtained in order to characterize the effectiveness and probability of failure on demand of relevant safety barriers. The methodology was exemplified with a case study. The results obtained define a procedure for the estimation of safety barrier performance in the prevention of fire escalation in domino scenarios. - Highlights: • We developed a methodology for the quantitative assessment of safety barriers. • We focused on safety barriers aimed at preventing domino effect triggered by fire. • We obtained data on effectiveness and availability of the safety barriers. • The methodology was exemplified with a case study of industrial interest. • The results showed the role of safety barriers in preventing fired domino escalation

Crossing safety barriers: influence of children's morphological and functional variables.

Science.gov (United States)

Cordovil, Rita; Vieira, Filomena; Barreiros, João

2012-05-01

Thirty-three children between 3 and 6 years of age were asked to climb four different types of safety barriers. Morphological and functional variables of the children, which were expected to influence climbing or passing through skills, were collected. The influence of those variables on children's success rate and time to cross was tested. No barrier offered a total restraining efficacy. The horizontal bars barrier was crossed by 97% of the children. In the group of children that succeeded in crossing the four barriers, mean time to cross the most difficult barrier was 15 s. Age was the best predictor for success in crossing most barriers but morphology and strength were important predictors of time to cross. The influence of anthropometric variables in time to cross was dependent upon the characteristics of the barrier. A good design of safety barriers should consider children's age, morphology and strength. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

A simple reliability block diagram method for safety integrity verification

International Nuclear Information System (INIS)

Guo Haitao; Yang Xianhui

2007-01-01

IEC 61508 requires safety integrity verification for safety related systems to be a necessary procedure in safety life cycle. PFD avg must be calculated to verify the safety integrity level (SIL). Since IEC 61508-6 does not give detailed explanations of the definitions and PFD avg calculations for its examples, it is difficult for common reliability or safety engineers to understand when they use the standard as guidance in practice. A method using reliability block diagram is investigated in this study in order to provide a clear and feasible way of PFD avg calculation and help those who take IEC 61508-6 as their guidance. The method finds mean down times (MDTs) of both channel and voted group first and then PFD avg . The calculated results of various voted groups are compared with those in IEC61508 part 6 and Ref. [Zhang T, Long W, Sato Y. Availability of systems with self-diagnostic components-applying Markov model to IEC 61508-6. Reliab Eng System Saf 2003;80(2):133-41]. An interesting outcome can be realized from the comparison. Furthermore, although differences in MDT of voted groups exist between IEC 61508-6 and this paper, PFD avg of voted groups are comparatively close. With detailed description, the method of RBD presented can be applied to the quantitative SIL verification, showing a similarity of the method in IEC 61508-6

Safety assessment of discharge chute isolation barrier preparation and installation

International Nuclear Information System (INIS)

Meichle, R.H.

1994-01-01

This analysis examines activities associated with the installation of isolation barriers in the K Basins at the Hanford Reservation. This revision adds evaluation of barrier drops on stored fuel and basin floor, identifies fuel which will be moved and addresses criticality issues with sludge. The safety assessment is made for the activities for the preparation and installation of the discharge chute isolation barriers. The safety assessment includes a hazard assessment and comparisons of potential accidents/events to those addressed by the current safety basis documentation. No significant hazards were identified. An evaluation against the USQ evaluation questions was made and the determination made that the activities do not represent a USQ. Hazard categorization techniques were used to provide a basis for readiness review classifications

Identifying Food Safety Concerns when Communication Barriers Exist

Science.gov (United States)

Neal, Jack A.; Dawson, Mary; Madera, Juan M.

2011-01-01

Abstract: Students must be prepared to lead a diverse workforce. The objective of this study was to establish a teaching method that helps students identify barriers to food safety while working in a simulated environment with communication barriers. This study employed a perspective taking exercise based upon the principles of social learning…

Modeling Safety Barriers and Defense in Depth with Mulitlevel Flow Modeling

DEFF Research Database (Denmark)

Lind, Morten

2012-01-01

in MFM is a barrier function. It is shown that other barrier types can be represented andthat their combination into barrier chains may be used to analyze and design levels of safety in automated processes.Suggestion for further research on barrier modeling with MFM are included....

Analysis of developed transition road safety barrier systems.

Science.gov (United States)

Soltani, Mehrtash; Moghaddam, Taher Baghaee; Karim, Mohamed Rehan; Sulong, N H Ramli

2013-10-01

Road safety barriers protect vehicles from roadside hazards by redirecting errant vehicles in a safe manner as well as providing high levels of safety during and after impact. This paper focused on transition safety barrier systems which were located at the point of attachment between a bridge and roadside barriers. The aim of this study was to provide an overview of the behavior of transition systems located at upstream bridge rail with different designs and performance levels. Design factors such as occupant risk and vehicle trajectory for different systems were collected and compared. To achieve this aim a comprehensive database was developed using previous studies. The comparison showed that Test 3-21, which is conducted by impacting a pickup truck with speed of 100 km/h and angle of 25° to transition system, was the most severe test. Occupant impact velocity and ridedown acceleration for heavy vehicles were lower than the amounts for passenger cars and pickup trucks, and in most cases higher occupant lateral impact ridedown acceleration was observed on vehicles subjected to higher levels of damage. The best transition system was selected to give optimum performance which reduced occupant risk factors using the similar crashes in accordance with Test 3-21. Copyright © 2013 Elsevier Ltd. All rights reserved.

Language barriers and patient safety risks in hospital care. A mixed methods study.

Science.gov (United States)

van Rosse, Floor; de Bruijne, Martine; Suurmond, Jeanine; Essink-Bot, Marie-Louise; Wagner, Cordula

2016-02-01

A language barrier has been shown to be a threat for quality of hospital care. International studies highlighted a lack of adequate noticing, reporting, and bridging of a language barrier. However, studies on the link between language proficiency and patient safety are scarce, especially in Europe. The present study investigates patient safety risks due to language barriers during hospitalization, and the way language barriers are detected, reported, and bridged in Dutch hospital care. We combined quantitative and qualitative methods in a sample of 576 ethnic minority patients who were hospitalized on 30 wards within four urban hospitals. The nursing and medical records of 17 hospital admissions of patients with language barriers were qualitatively analyzed, and complemented by 12 in-depth interviews with care providers and patients and/or their relatives to identify patient safety risks during hospitalization. The medical records of all 576 patients were screened for language barrier reports. The results were compared to patients' self-reported Dutch language proficiency. The policies of wards regarding bridging language barriers were compared with the reported use of interpreters in the medical records. Situations in hospital care where a language barrier threatened patient safety included daily nursing tasks (i.e. medication administration, pain management, fluid balance management) and patient-physician interaction concerning diagnosis, risk communication and acute situations. In 30% of the patients that reported a low Dutch proficiency, no language barrier was documented in the patient record. Relatives of patients often functioned as interpreter for them and professional interpreters were hardly used. The present study showed a wide variety of risky situations in hospital care for patients with language barriers. These risks can be reduced by adequately bridging the language barrier, which, in the first place, demands adequate detecting and reporting of a

A decision model to allocate protective safety barriers and mitigate domino effects

International Nuclear Information System (INIS)

Janssens, Jochen; Talarico, Luca; Reniers, Genserik; Sörensen, Kenneth

2015-01-01

In this paper, we present a model to support decision-makers about where to locate safety barriers and mitigate the consequences of an accident triggering domino effects. Based on the features of an industrial area that may be affected by domino accidents, and knowing the characteristics of the safety barriers that can be installed to stall the fire propagation between installations, the decision model can help practitioners in their decision-making. The model can be effectively used to decide how to allocate a limited budget in terms of safety barriers. The goal is to maximize the time-to-failure of a chemical installation ensuring a worst case scenario approach. The model is mathematically stated and a flexible and effective solution approach, based on metaheuristics, is developed and tested on an illustrative case study representing a tank storage area of a chemical company. We show that a myopic optimization approach, which does not take into account knock-on effects possibly triggered by an accident, can lead to a distribution of safety barriers that are not effective in mitigating the consequences of a domino accident. Moreover, the optimal allocation of safety barriers, when domino effects are considered, may depend on the so-called cardinality of the domino effects. - Highlights: • A model to allocate safety barriers and mitigate domino effects is proposed. • The goal is to maximize the escalation time of the worst case scenario. • The model provides useful recommendations for decision makers. • A fast metaheuristic approach is proposed to solve such a complex problem. • Numerical simulations on a realistic case study are shown

Project Guarantee 1985. Final repository for high-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

Final disposal of radioactive waste involves preventing the waste from returning from the repository location into the biosphere by means of successively arranged containment measures known as safety barriers. In the present volume NGB 85-04 of the series of reports for Project 'Guarantee' 1985, the safety barrier system for the type C repository for high-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). Safety barriers take the form of both technically constructed containment measures and the siting of the repository in suitable geological formations. The technical safety barrier system in the case of high-level waste comprises: the waste solidification matrix (borosilicate glass), massive steel canisters, encasement of the waste canisters, encasement of the waste canisters in highly compacted bentonite, sealing of vacant storage space and access routes on repository closure. The natural geological safety barriers - the host rock and overlying formations provide sufficiently long deep groundwater flow times from the repository location to the earth's surface and for additional lengthening of radionuclide migration times by means of various chemical and physical retardation mechanisms. The stability of the geological formations is so great that hydrogeological system is protected for a sufficient length of time from deterioration caused, in particular, by erosion. Observations in the final section of the report indicate that input data for the type C repository safety

Safety performance evaluation of cable median barriers on freeways in Florida.

Science.gov (United States)

Alluri, Priyanka; Haleem, Kirolos; Gan, Albert; Mauthner, John

2016-07-03

This article aims to evaluate the safety performance of cable median barriers on freeways in Florida. The safety performance evaluation was based on the percentages of barrier and median crossovers by vehicle type, crash severity, and cable median barrier type (Trinity Cable Safety System [CASS] and Gibraltar system). Twenty-three locations with cable median barriers totaling about 101 miles were identified. Police reports of 6,524 crashes from years 2005-2010 at these locations were reviewed to verify and obtain detailed crash information. A total of 549 crashes were determined to be barrier related (i.e., crashes involving vehicles hitting the cable median barrier) and were reviewed in further detail to identify crossover crashes and the manner in which the vehicles crossed the barriers; that is, by either overriding, underriding, or penetrating the barriers. Overall, 2.6% of vehicles that hit the cable median barrier crossed the median and traversed into the opposite travel lane. Overall, 98.1% of cars and 95.5% of light trucks that hit the barrier were prevented from crossing the median. In other words, 1.9% of cars and 4.5% of light trucks that hit the barrier had crossed the median and encroached on the opposite travel lanes. There is no significant difference in the performance of cable median barrier for cars versus light trucks in terms of crossover crashes. In terms of severity, overrides were more severe compared to underrides and penetrations. The statistics showed that the CASS and Gibraltar systems performed similarly in terms of crossover crashes. However, the Gibraltar system experienced a higher proportion of penetrations compared to the CASS system. The CASS system resulted in a slightly higher percentage of moderate and minor injury crashes compared to the Gibraltar system. Cable median barriers are successful in preventing median crossover crashes; 97.4% of the cable median barrier crashes were prevented from crossing over the median. Of all of

76 FR 34145 - Safety Zone, Barrier Testing Operations, Chicago Sanitary and Ship Canal, Romeoville, IL

Science.gov (United States)

2011-06-13

...-AA00 Safety Zone, Barrier Testing Operations, Chicago Sanitary and Ship Canal, Romeoville, IL AGENCY.... Construction on Barrier IIB has been completed. Operational and safety testing was conducted in February 2011... dispersal barrier IIA and IIB. This safety zone will be enforced daily from 7 a.m. to 11 a.m. and from 1 p.m...

Barriers to occupational health and safety management in small Brazilian enterprises

OpenAIRE

Garnica, Guilherme Besse; Barriga, Gladys Dorotea Cacsire

2018-01-01

Abstract Paper aims To determine main barriers to the implementation of occupational health and safety management systems OHSMS in the context of small Brazilian enterprises from the perspectives of owners/managers, labor auditors, and OHS consultants. Originality: Survey with three different perspectives on small Brazilian enterprises. Research method: Survey conducted with stakeholders who influence the safety culture in small enterprises to identify the main barriers to the implementati...

Final disposal in deep boreholes using multiple geological barriers. Digging deeper for safety. Proceedings

Energy Technology Data Exchange (ETDEWEB)

Bracke, Guido; Hurst, Stephanie; Merkel, Broder; Mueller, Birgit; Schilling, Frank

2016-03-15

The proceedings of the workshop on final disposal in deep boreholes using multiple geological barriers - digging deeper for safety include contributions on the following topics: international status and safety requirements; geological and physical barriers; deep drilling - shaft building; technical barriers and emplacement technology for high P/T conditions; recovery (waste retrieval); geochemistry and monitoring.

Modelling of safety barriers including human and organisational factors to improve process safety

DEFF Research Database (Denmark)

Markert, Frank; Duijm, Nijs Jan; Thommesen, Jacob

2013-01-01

It is believed that traditional safety management needs to be improved on the aspect of preparedness for coping with expected and unexpected deviations, avoiding an overly optimistic reliance on safety systems. Remembering recent major accidents, such as the Deep Water Horizon, the Texas City....... A valuable approach is the inclusion of human and organisational factors into the simulation of the reliability of the technical system using event trees and fault trees and the concept of safety barriers. This has been demonstrated e.g. in the former European research project ARAMIS (Accidental Risk...

Project Guarantee 1985. Final repository for low- and intermediate-level radioactive wastes: The system of safety barriers

International Nuclear Information System (INIS)

Anon.

1985-01-01

The safety barrier system for the type B repository for low- and intermediate-level waste is described. The barrier parameters which are relevant for safety analysis are quantified and associated error limits and data scatter are given. The aim of the report is to give a summary documentation of the safety analysis input data and their scientific background. For secure containment of radioactive waste safety barriers are used which effectively limit the release of radioactive material from the repository (release barriers) and effectively retard the entry of the original radioactive material into the biosphere (time barriers). In the case of low- and intermediate-level waste the technical safety barrier system comprises: waste solidification matrix (cement, bitumen and resin), immobilisation of the waste packages in containers using liquid cement, concrete repository containers, backfilling of remaining vacant storage space with special concrete, concrete lining of the repository caverns, sealing of access tunnels on final closure of the repository. Natural geological safety barriers - host rock and overlying formations - have the following important functions. Because of its stability, the host rock in the repository zone protects the technical safety barrier system from destruction caused by climatic effects and erosion for a sufficient length of time. It also provides for low water flow and favourable chemistry (reducing conditions)

Barrier and system performances within a safety case: their functioning and evolution with time

International Nuclear Information System (INIS)

Hedin, A.; Voinis, S.; Fillion, E.; Keller, S.; Lalieux, Ph.; Nachmilner, L.; Nys, V.; Rodriguez, J.; Sevougian, D.; Wollrath, J.

2002-01-01

The following six questions were used as the basis for the discussions in a Working Group: - What is the role of each barrier as a function of time or in the different time frames? What is its contribution to the overall system performance or safety as a function of time? - Which are the main uncertainties on the performance of barriers in the timescales? To what extent should we enhance the robustness of barriers because of the uncertainties of some component behaviour with time? - What is the requested or required performance versus the expected realistic or conservative behaviour with time? How are these safety margins used as arguments in a safety case? - What is the issue associated with the geosphere stability for different geological systems? - How are barriers and system performances, as a function of time, evaluated (presented and communicated) in a safety case? - What kind of measures are used for siting, designing and optimising robust barriers corresponding to situations that can vary with time? Are human actions considered to be relevant? (authors)

Use of safety case to accomplish with Brazilian regulations for drilling units; Uso de caso de seguranca para cumprir com as normas brasileiras para unidades de perfuracao: metodologia Bow Tie

Energy Technology Data Exchange (ETDEWEB)

Bardy, Mariana; Silveira, Paula Dias; Oliveira, Katia [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil). Risk Advisory

2012-07-01

The last accidents on the industry, mainly after BP accident in Texas City and Macondo blowout, showed and increased the importance of safety barriers on prevention of such events. The safety barriers can be identified in risk analysis studies such as Preliminary Hazard Analysis or HAZOP. But, the identification of safety barriers is not enough, it is necessary to maintain their integrity to guarantee that when demanded they work properly as expected. The methodology presented in this document aim to evaluate the integrity condition of safety barriers and their compliance with the project original characteristics using the Bow Tie and an audit process, and searching for actions that can guarantee the barriers integrity when demanded in a proactive way. The Bow Tie diagrams provide a graphic picture of accidental scenarios, join a relational perspective between event, cause, consequence and barriers, and additionally provide a clear view of possible threats and consequences related with events with high damage potential. The application of methodology described in this document is presented based on a case study related to an accidental release of flammable liquid due to dropped objects on the topside of an offshore unit. Among the benefits identified using this proposed methodology it can be highlighted the possibility to form an integrated overview of management system and of factors that can reduce losses. The Bow Tie diagram provides an overview of process accidents, in several different organization levels, and the integration between different areas responsible for management of different barriers groups. Complementing those diagrams with an audit process it can be determined the real image of company management system related to process safety, which make possible the identification of main points for improvement. (author)

Safety barriers to prevent release of hydrocarbons during production of oil and gas

OpenAIRE

Sklet, Snorre; Hauge, Stein

2004-01-01

This report documents a set of scenarios related to release of hydrocarbons during production on oil and gas platforms. For each release scenario, initiating events, barrier functions aimed to prevent loss of containment, and barrier systems that realize these barrier functions are identified and described. Safety barriers to prevent release of hydrocarbons during production of oil and gas

Barriers to occupational health and safety management in small Brazilian enterprises

Directory of Open Access Journals (Sweden)

Guilherme Besse Garnica

2018-02-01

Full Text Available Abstract Paper aims To determine main barriers to the implementation of occupational health and safety management systems OHSMS in the context of small Brazilian enterprises from the perspectives of owners/managers, labor auditors, and OHS consultants. Originality: Survey with three different perspectives on small Brazilian enterprises. Research method: Survey conducted with stakeholders who influence the safety culture in small enterprises to identify the main barriers to the implementation of OHSMS. Main findings: Owners/managers tend to blame employees and the government for difficulty in implementing OHSMS, and external actors tend to blame management and resource allocation. Opinions converge on inappropriate management behavior, ineffective information and communication and production prioritization. Implications for theory and practice: These barriers should be overcome not only to facilitate the implementation of OHSMS but also to improve the conditions for the management of all small business operations.

PReSaFe: A model of barriers and facilitators to patients providing feedback on experiences of safety.

Science.gov (United States)

De Brún, Aoife; Heavey, Emily; Waring, Justin; Dawson, Pamela; Scott, Jason

2017-08-01

The importance of involving patients in reporting on safety is increasingly recognized. Whilst studies have identified barriers to clinician incident reporting, few have explored barriers and facilitators to patient reporting of safety experiences. This paper explores patient perspectives on providing feedback on safety experiences. Patients (n=28) were invited to take part in semi-structured interviews when given a survey about their experiences of safety following hospital discharge. Transcripts were thematically analysed using NVivo10. Patients were recruited from four hospitals in the UK. Three themes were identified as barriers and facilitators to patient involvement in providing feedback on their safety experiences. The first, cognitive-cultural, found that whilst safety was a priority for most, some felt the term was not relevant to them because safety was the "default" position, and/or because safety could not be disentangled from the overall experience of care. The structural-procedural theme indicated that reporting was facilitated when patients saw the process as straightforward, but that disinclination or perceived inability to provide feedback was a barrier. Finally, learning and change illustrated that perception of the impact of feedback could facilitate or inhibit reporting. When collecting patient feedback on experiences of safety, it is important to consider what may help or hinder this process, beyond the process alone. We present a staged model of prerequisite barriers and facilitators and hypothesize that each stage needs to be achieved for patients to provide feedback on safety experiences. Implications for collecting meaningful data on patients' safety experiences are considered. © 2016 The Authors. Health Expectations Published by John Wiley & Sons Ltd.

Stabilization with guaranteed safety using Control Lyapunov–Barrier Function

NARCIS (Netherlands)

Romdlony, Muhammad Zakiyullah; Jayawardhana, Bayu

2016-01-01

We propose a novel nonlinear control method for solving the problem of stabilization with guaranteed safety for nonlinear systems. The design is based on the merging of the well-known Control Lyapunov Function (CLF) and the recent concept of Control Barrier Function (CBF). The proposed control

Safety Performance Evaluations for the Vehicle Based Movable Barriers Using Full Scale Crash Tests

Directory of Open Access Journals (Sweden)

Jin Minsoo

2017-01-01

Full Text Available The present study aims to develop a prototype of large-size movable barriers to protect roadside workers from incoming vehicles to the road work area with the following functions: maximization of work space in the right and left directions, convenient mobility, and minimization of impact without modification of the inside of movable barriers into traffic lanes and perform safety performance assessment on passengers through full scale crash tests. The large movable barrier was divided into folder type and telescope type and the development stage was now at the prototype phase. A full scale crash test was conducted prior to certification test at a level of 90%. The full scale crash test result showed that both types of folder type movable barrier and telescope type movable barrier satisfied the standard of the passenger safety performance evaluation at a level of 90%.

Barriers to Safety Event Reporting in an Academic Radiology Department: Authority Gradients and Other Human Factors.

Science.gov (United States)

Siewert, Bettina; Swedeen, Suzanne; Brook, Olga R; Eisenberg, Ronald L; Hochman, Mary

2018-05-15

Purpose To investigate barriers to reporting safety concerns in an academic radiology department and to evaluate the role of human factors, including authority gradients, as potential barriers to safety concern reporting. Materials and Methods In this institutional review board-approved, HIPAA-compliant retrospective study, an online questionnaire link was emailed four times to all radiology department staff members (n = 648) at a tertiary care institution. Survey questions included frequency of speaking up about safety concerns, perceived barriers to speaking up, and the annual number of safety concerns that respondents were unsuccessful in reporting. Respondents' sex, role in the department, and length of employment were recorded. Statistical analysis was performed with the Fisher exact test. Results The survey was completed by 363 of the 648 employees (56%). Of those 363 employees, 182 (50%) reported always speaking up about safety concerns, 134 (37%) reported speaking up most of the time, 36 (10%) reported speaking up sometimes, seven (2%) reported rarely speaking up, and four (1%) reported never speaking up. Thus, 50% of employees spoke up about safety concerns less than 100% of the time. The most frequently reported barriers to speaking up included high reporting threshold (69%), reluctance to challenge someone in authority (67%), fear of disrespect (53%), and lack of listening (52%). Conclusion Of employees in a large academic radiology department, 50% do not attain 100% reporting of safety events. The most common human barriers to speaking up are high reporting threshold, reluctance to challenge authority, fear of disrespect, and lack of listening, which suggests that existing authority gradients interfere with full reporting of safety concerns. © RSNA, 2018.

Language barriers and patient safety risks in hospital care: a mixed methods study.

NARCIS (Netherlands)

Rosse, F. van; Bruijne, M. de; Suurmond, J.; Essink-Bot, M.L.; Wagner, C.

2016-01-01

Introduction: A language barrier has been shown to be a threat for quality of hospital care. International studies highlighted a lack of adequate noticing, reporting, and bridging of a language barrier. However, studies on the link between language proficiency and patient safety are scarce,

Language barriers and patient safety risks in hospital care. A mixed methods study

NARCIS (Netherlands)

van Rosse, Floor; de Bruijne, Martine; Suurmond, Jeanine; Essink-Bot, Marie-Louise; Wagner, Cordula

2016-01-01

A language barrier has been shown to be a threat for quality of hospital care. International studies highlighted a lack of adequate noticing, reporting, and bridging of a language barrier. However, studies on the link between language proficiency and patient safety are scarce, especially in Europe.

Pembuatan Kakas Bantu untuk Mendeteksi Ketidaksesuaian Diagram Urutan (Sequence Diagram dengan Diagram Kasus Penggunaan (Use Case Diagram

Directory of Open Access Journals (Sweden)

Andrias Meisyal Yuwantoko

2017-03-01

Full Text Available Sebuah diagram urutan dibuat  berdasarkan alur yang ada pada deskripsi kasus penggunaan. Alur tersebut dire- presentasikan dalam  bentuk  interaksi antara aktor  dan  sistem. Pemeriksaan rancangan diagram urutan perlu dilakukan untuk mengetahui ketidaksesuaian urutan alur  kasus penggunaan dengan urutan pesan yang dikirimkan oleh objek-objek pada diagram urutan. Rancangan diagram yang sesuai merupakan kunci ketepatan (correctness implementasi  perangkat lunak. Namun, pemeriksaan ketidaksesuaian masih dilakukan secara manual. Hal ini menjadi masalah apabila sebuah proyek perangkat lunak memiliki banyak  rancangan diagram dan sumber daya manusia tidak  mencukupi. Pemeriksaan membutuhkan waktu yang lama dan memiliki dampak pada waktu pengembangan perangkat lunak. Penelitian ini mengusulkan pembuatan kakas bantu  untuk mendeteksi ketidaksesuaian diagram urutan dengan diagram kasus penggunaan. Ketidaksesuaian dilihat dari kemiripan semantik kalimat antara alur pada deskripsi kasus penggunaan dan triplet. Dari hasil pembuatan kakas bantu, kakas bantu yang dibuat dapat mendeteksi ketidaksesuaian diagram urutan dengan diagram kasus penggunaan. Kakas  bantu ini diharapkan tidak hanya membantu pemeriksaan rancangan diagram akan tetapi mempercepat waktu pengembangan perangkat lunak.

From State Diagram to Class Diagram

DEFF Research Database (Denmark)

Borch, Ole; Madsen, Per Printz

2009-01-01

UML class diagram and Java source code are interrelated and Java code is a kind of interchange format. Working with UML state diagram in CASE tools, a corresponding xml file is maintained. Designing state diagrams is mostly performed manually using design patterns and coding templates - a time...... consuming process. This article demonstrates how to compile such a diagram into Java code and later, by reverse engineering, produce a class diagram. The process from state diagram via intermediate SAX parsed xml file to Apache Velocity generated Java code is described. The result is a fast reproducible...

Barriers and limitations during implementation of the surgical safety checklist of the World Health Organization

OpenAIRE

Rosa Amalia Arboleda; Andrés Felipe Ausenón; Jairo Alberto Ayala; Diana Carolina Cabezas; Lina Gissella Calvache; Juan Pablo Caicedo; Jose Andres Calvache

2014-01-01

Introduction: The surgical safety checklist of the World Health Organization (WHO) is a tool that checks and evaluates each procedure in the operating room. Despite its demonstrated effectiveness, it has many limitations and barriers to its implementation. The aim of this article was to present the current evidence regarding limitations and barriers to achieve a successful implementation of the surgical safety WHO checklist. Methods: A narrative review was designed. We performed a systematic ...

[Identification of meridian-acupoint diagrams and meridian diagrams].

Science.gov (United States)

Shen, Wei-hong

2008-08-01

In acu-moxibustion literature, there are two kinds of diagrams, meridian-acupoint diagrams and meridian diagrams. Because they are very similar in outline, and people now have seldom seen the typical ancient meridian diagrams, meridian-acupoint diagrams have been being incorrectly considered to be the meridian diagrams for a long time. It results in confusion in acu-moxibustion academia. The present paper stresses its importance in academic research and introduces some methods for identifying them correctly. The key points for identification of meridian-acupoint diagrams and meridian diagrams are: the legend of diagrams and the drawing style of the ancient charts. In addition, the author makes a detailed explanation about some acu-moxibustion charts which are easily confused. In order to distinguish meridian-acupoint diagrams and meridian diagrams correctly, he or she shoulnd understand the diagrams' intrinsic information as much as possible and make a comprehensive analysis about them.

Quantitative assessment of probability of failing safely for the safety instrumented system using reliability block diagram method

International Nuclear Information System (INIS)

Jin, Jianghong; Pang, Lei; Zhao, Shoutang; Hu, Bin

2015-01-01

Highlights: • Models of PFS for SIS were established by using the reliability block diagram. • The more accurate calculation of PFS for SIS can be acquired by using SL. • Degraded operation of complex SIS does not affect the availability of SIS. • The safe undetected failure is the largest contribution to the PFS of SIS. - Abstract: The spurious trip of safety instrumented system (SIS) brings great economic losses to production. How to ensure the safety instrumented system is reliable and available has been put on the schedule. But the existing models on spurious trip rate (STR) or probability of failing safely (PFS) are too simplified and not accurate, in-depth studies of availability to obtain more accurate PFS for SIS are required. Based on the analysis of factors that influence the PFS for the SIS, using reliability block diagram method (RBD), the quantitative study of PFS for the SIS is carried out, and gives some application examples. The results show that, the common cause failure will increase the PFS; degraded operation does not affect the availability of the SIS; if the equipment was tested and repaired one by one, the unavailability of the SIS can be ignored; the corresponding occurrence time of independent safe undetected failure should be the system lifecycle (SL) rather than the proof test interval and the independent safe undetected failure is the largest contribution to the PFS for the SIS

Impact of changed fuel performances on safety barrier effectiveness at normal operation of NPP with WWER

International Nuclear Information System (INIS)

Zhurbenko, A. V.; Semchenkov, Y. M.; Slavyagin, P.D.

2007-01-01

The paper presents the analysis of adopted safety barriers against propagation of fission product released from WWER core of active power plants. Relationship between system and equipment performances and safety barriers is demonstrated. The fundamental principles of methodological approach to the operational limit determination based on the assessment of iodine-131 specific activity in the primary circuit are discussed. Problems of substantiating the operational limit for primary coolant activity are analyzed for conditions of growing burnup (Authors)

Barriers to Implementing a Reporting and Learning Patient Safety System: Pediatric Chiropractic Perspective.

Science.gov (United States)

Pohlman, Katherine A; Carroll, Linda; Hartling, Lisa; Tsuyuki, Ross T; Vohra, Sunita

2016-04-01

A reporting and learning system is a method of monitoring the occurrence of incidents that affect patient safety. This cross-sectional survey asked pediatric chiropractors about factors that may limit their participation in such a system. The list of potential barriers for participation was developed using a systematic approach. All members of the 2 pediatric councils associated with US national chiropractic organizations were invited to complete the survey (N = 400). The cross-sectional survey was created using an online survey tool (REDCap) and sent directly to member emails addressed by the respective executive committees. Of the 400 potential respondents, 81 responded (20.3%). The most common limitations to participating were identified as time pressure (96%) and patient concerns (81%). Reporting and learning systems have been utilized to increase safety awareness in many high-risk industries. To be successful, future patient safety studies with pediatric chiropractors need to ensure these barriers are understood and addressed. © The Author(s) 2015.

Linking Safety Analysis to Safety Requirements

DEFF Research Database (Denmark)

Hansen, Kirsten Mark

Software for safety critical systems must deal with the hazards identified by safety analysistechniques: Fault trees, event trees,and cause consequence diagrams can be interpreted as safety requirements and used in the design activity. We propose that the safety analysis and the system design use...

Safety indicators used to prove the role of natural barrier for Saligny near surface disposal system

International Nuclear Information System (INIS)

Niculae, Ortenzia; Durdun, I.; Ionita, Gh.

2007-01-01

Full text: The siting process for a near surface repository suitable for the radioactive waste resulted from Cernavoda NPP operation and decommissioning (low level radioactive waste with small amounts of long lived radionuclides) started in 1992 and it included the collection of data from specific field and laboratory works for each site selection stage as well as different safety performance evaluation. According to the IAEA standards (Safety Guide No.111-G-3.1, 1994), the purpose of the siting process is not to get the best solution but to find out 'an acceptable solution, with sufficient safety reserves'. Since 1996, detailed field and investigation works were performed in Saligny preferred site including an experimental area to test the improvement method proposed for the foundation ground of repository, as well as detailed performance assessments using specific computer codes. The paper presents the results of recent performance assessments for the natural barrier of disposal system. The calculations were done using HYDRUS 2D, FEHM and AMBER computer codes. The endpoint of the Safety Report for Siting a Near Surface Repository at Saligny Site [CITON and SCN, Safety Report for Siting a Near Surface Repository at Saligny Site, 2007, pages 8.2.1-1 to 8.2.1-22 and 8-63 to 8-70] was the assessment of safety indicators. Individual annual effective dose for exposed peoples (both workers and general public) was the main safety indicator. In the same document, the radionuclide concentration in the disposal system compartments has been evaluated, as supplementary safety indicator of repository barriers (especially to confirm the natural barrier performance). The results confirmed the performance of natural barrier: the maximum extension of H-3 and Co-60 contaminant plume after repository closure remains more above underground water level. In the aquifer, iodine concentration reaches a value of 10 -15 mol/l, at the same magnitude order with the admitted limit from CFR

Fulfillment of the long-term safety functions by the different barriers during the main time frames after repository closure

International Nuclear Information System (INIS)

Preter, P. de; Lalieux, Ph.

2002-01-01

In general terms the basis long-term safety functions of a disposal system (i.e. the engineered barrier system, including the waste forms and the host rock) are the functions that the system as a whole or its constituents must fulfill in order to assure an adequate level of long-term radiological safety. The long-term safety functions of a disposal system constitute a generic and methodological tool that can be used in a double sense. In the first place these functions provide an a priori instrument for designing the system: the implementer must ensure that these safety functions are fulfilled by a series of robust system barriers and components. These functions can also be used as an a posteriori means to describe and assess in general terms the functioning of the system. In this way they are an important qualitative element to help to support the safety case and to identify further R and D priorities. By providing a general description of system functioning they are also a communication tool to stakeholders who are less familiar with the details of a safety case. Instead of limiting the description to a multi-barrier system, the safety functions enable to better explain how the different barriers contribute to one or more safety functions and by which processes this is performed. By doing so the system description moves from multi-barrier to multi-function. The aim of this paper is to provide such a general description of the system functioning for the Belgian case of deep disposal of high-level waste (mainly spent fuel or vitrified waste from fuel reprocessing) in the Boom Clay, o poorly-indurated argillaceous formation. From the detailed safety and performance evaluations the main time frames after repository closure are identified. Each time frame relates to a period during which the successive safety functions play a key role. Also, in each time frame the radiological impact on the environment is distinctly different. (authors)

Understanding parental motivators and barriers to uptake of child poison safety strategies: a qualitative study.

Science.gov (United States)

Gibbs, L; Waters, E; Sherrard, J; Ozanne-Smith, J; Robinson, J; Young, S; Hutchinson, A

2005-12-01

To develop an understanding of factors acting as barriers and motivators to parental uptake of child poison safety strategies. A qualitative study involving semistructured interviews and focus groups. A grounded theory approach was used for the collection and analysis of data. Sixty five parents of children under 5 years of age, some of whom had experienced an unintentional child poisoning incident. A range of knowledge based, environmental, and behavioral barriers to comprehensive parental uptake of poison safety practices were identified. As a result there tended to be only partial implementation of safety initiatives in the home. Selection of safety practices was often guided by the interests and behaviors of the child. This made the child vulnerable to changes in the home environment, inadequate supervision, and/or shifts in their own behavior and developmental ability. Personal or vicarious exposure of a parent to a child poisoning incident was a significant motivator for parental review of safety practices. Environmental measures targeting child resistant containers, warning labels, and lockable poisons cupboards will support parents' efforts to maintain poison safety. Additional education campaigns using stories of actual poisoning incidents may help to increase awareness of risk and encourage increased uptake.

Engineered barrier systems (EBS) in the context of the entire safety case

International Nuclear Information System (INIS)

2003-01-01

A joint NEA-EC workshop entitled 'Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case' was organised in Oxford on 25-27 September 2002 and hosted by United Kingdom Nirex Limited. The main objectives of the workshop were to provide a status report on engineered barrier systems in various national radioactive waste management programmes considering deep geological disposal; to establish the value to member countries of a project on EBS; and to define such a project's scope, timetable and modus operandi. This report presents the outcomes of this workshop. (author)

Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case

International Nuclear Information System (INIS)

2005-01-01

A joint NEA-EC workshop entitled ''Engineered Barrier Systems (EBS) in the Context of the Entire Safety Case'' was organised in Oxford on 25-27 September 2002 and hosted by United Kingdom Nirex Limited. The main objectives of the workshop were to provide a status report on engineered barrier systems in various national radioactive waste management programmes considering deep geological disposal; to establish the value to member countries of a project on EBS; and to define such a project scope, timetable and modus operandi. This report presents the outcomes of this workshop. (author)

Simulation of crash tests for high impact levels of a new bridge safety barrier

Science.gov (United States)

Drozda, Jiří; Rotter, Tomáš

2017-09-01

The purpose is to show the opportunity of a non-linear dynamic impact simulation and to explain the possibility of using finite element method (FEM) for developing new designs of safety barriers. The main challenge is to determine the means to create and validate the finite element (FE) model. The results of accurate impact simulations can help to reduce necessary costs for developing of a new safety barrier. The introductory part deals with the creation of the FE model, which includes the newly-designed safety barrier and focuses on the application of an experimental modal analysis (EMA). The FE model has been created in ANSYS Workbench and is formed from shell and solid elements. The experimental modal analysis, which was performed on a real pattern, was employed for measuring the modal frequencies and shapes. After performing the EMA, the FE mesh was calibrated after comparing the measured modal frequencies with the calculated ones. The last part describes the process of the numerical non-linear dynamic impact simulation in LS-DYNA. This simulation was validated after comparing the measured ASI index with the calculated ones. The aim of the study is to improve professional public knowledge about dynamic non-linear impact simulations. This should ideally lead to safer, more accurate and profitable designs.

Language Differences as a Barrier to Quality and Safety in Health Care: The Joint Commission Perspective

OpenAIRE

Schyve, Paul M.

2007-01-01

Effective communication with patients is critical to the safety and quality of care. Barriers to this communication include differences in language, cultural differences, and low health literacy. Evidence-based practices that reduce these barriers must be integrated into, rather than just added to, health care work processes.

Safety assessment of discharge chute isolation barrier preparation and installation activities. Revision 3

International Nuclear Information System (INIS)

Meichle, R.H.

1994-01-01

This revision adds a section addressing impacts of dropping surfacing tool and rack cutter on the basin floor, and corrects typographical errors. The safety assessment is made for the activities for the preparation and installation of the discharge chute isolation barriers. The safety assessment includes a hazard assessment and comparisons of potential accidents/events to those addressed by the current safety basis documentation. No significant hazards were identified. An evaluation against the USQ evaluation questions was made and the determination made that the activities do not represent a USQ. Hazard categorization techniques were used to provide a basis for readiness review classifications

Translational safety biomarkers of colonic barrier integrity in the rat.

Science.gov (United States)

Erkens, Tim; Bueters, Ruud; van Heerden, Marjolein; Cuyckens, Filip; Vreeken, Rob; Goeminne, Nick; Lammens, Lieve

2018-05-20

The intestinal barrier controls intestinal permeability, and its disruption has been associated with multiple diseases. Therefore, preclinical safety biomarkers monitoring barrier integrity are essential during the development of drugs targeting the intestines, particularly if starting treatment early after onset of disease. Classical toxicology endpoints are not sensitive enough and therefore our objective was to identify non-invasive markers enabling early in vivo detection of colonic barrier perturbation. Male Sprague-Dawley rats were dosed intracolonically via the rectum, using sodium caprate or ibuprofen as tool compounds to alter barrier integrity. Several potentially translational biomarkers and probe molecules related to permeability, inflammation or tissue damage were evaluated, using various analytical platforms, including immunoassays, targeted metabolomics and highly sensitive ultra-performance liquid chromatography-tandem mass spectrometry. Several markers were identified that allow early in vivo detection of colonic barrier integrity changes, before histopathological evidence of tissue damage. The most promising permeability markers identified were plasma fluorescein isothiocyanate-dextran 4000 and a lactulose/mannitol/sucralose mixture in urine. These markers showed maximum increases over 100-fold or approximately 10-50-fold, respectively. Intracolonic administration of the above probe molecules outperformed oral administration and inflammatory or other biomarkers, such as α 2 -macroglobulin, calprotectin, cytokines, prostaglandins and a panel of metabolic molecules to identify early and subtle changes in barrier integrity. However, optimal timing of probe administration and sample collection is important for all markers evaluated. Inclusion of these probe molecules in preclinical toxicity studies might aid in risk assessment and the design of a clinical biomarker plan, as several of these markers have translational potential. Copyright © 2018 John

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips and Selby has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top node). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

Effect of joint mechanism on vehicle redirectional capability of water-filled road safety barrier systems.

Science.gov (United States)

Thiyahuddin, M I; Thambiratnam, D P; Gu, Y T

2014-10-01

Portable water-filled barriers (PWFBs) are roadside appurtenances that prevent vehicles from penetrating into temporary construction zones on roadways. PWFBs are required to satisfy the strict regulations for vehicle re-direction in tests. However, many of the current PWFBs fail to re-direct the vehicle at high speeds due to the inability of the joints to provide appropriate stiffness. The joint mechanism hence plays a crucial role in the performance of a PWFB system at high speed impacts. This paper investigates the desired features of the joint mechanism in a PWFB system that can re-direct vehicles at high speeds, while limiting the lateral displacement to acceptable limits. A rectangular "wall" representative of a 30m long barrier system was modeled and a novel method of joining adjacent road barriers was introduced through appropriate pin-joint connections. The impact response of the barrier "wall" and the vehicle was obtained and the results show that a rotational stiffness of 3000kNm/rad at the joints seems to provide the desired features of the PWFB system to re-direct impacting vehicles and restrict the lateral deflection. These research findings will be useful to safety engineers and road barrier designers in developing a new generation of PWFBs for increased road safety. Copyright © 2014 Elsevier Ltd. All rights reserved.

Investigating the influence on safety of retrofitting Italian motorways with barriers meeting a new EU standard.

Science.gov (United States)

Cafiso, Salvatore; D'Agostino, Carmelo; Persaud, Bhagwant

2017-04-03

A new European Union (EU) regulation for safety barriers, which is based on performance, has encouraged road agencies to perform an upgrade of old barriers, with the expectation that there will be safety benefits at the retrofitted sites. The new class of barriers was designed and installed in compliance with the 1998 (European Norm) EN 1317 standards for road restraint systems, which lays down common requirements for the testing and certification of road restraint systems in all countries of the European Committee for Standardization (CEN). Both the older and new barriers are made of steel and are installed in such a way as to avoid vehicle intrusion, but the older ones are thought to be only effective at low speeds and large angles of impact. The new standard seeks to remedy this by providing better protection at higher speeds. This article seeks to quantify the effect on the frequency of fatal and injury crashes of retrofitting motorways with barriers meeting the new standards. The estimation of the crash modification was carried out by performing an empirical Bayes before-after analysis based on data from the A18 Messina-Catania motorway in Italy. The methodology has the great advantage to account for the regression to the mean effects. Besides, to account for time trend effects and dispersion of crash data, a modified calibration methodology of safety performance was used. This study, based on data collected on 76 km of motorway in the period 2000-2012, derived Crash Modification Factor point estimates that indicate reductions of 72% for run-off-road fatal and injury crashes and 38% in total fatal and injury crashes that could be expected by upgrading an old safety barrier by complying with new EU 1317 standards. The estimated benefit-cost ratio of 5.57 for total crashes indicates that the treatment is cost effective. The magnitude of this benefit indicates that the retrofits are cost-effective even for total crashes and should continue in any European country

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1984-01-01

Recent work by Phillips et al., and Selby et al., has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. An influence diagram is a graphical representation of probabilistic dependence within a system or event sequence. Bayesian statistics are employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top event). As with fault trees, top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. Purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies. In addition, the computing efficiency of both methods is discussed

Diagram Size vs. Layout Flaws: Understanding Quality Factors of UML Diagrams

DEFF Research Database (Denmark)

Störrle, Harald

2016-01-01

, though, is our third goal of extending our analysis aspects of diagram quality. Method: We improve our definition of diagram size and add a (provisional) definition of diagram quality as the number of topographic layout flaws. We apply these metrics on 60 diagrams of the five most commonly used types...... of UML diagram. We carefully analyze the structure of our diagram samples to ensure representativeness. We correlate diagram size and layout quality with modeler performance data obtained in previous experiments. The data set is the largest of its kind (n-156). Results: We replicate earlier findings......, and extend them to two new diagram types. We provide an improved definition of diagram size, and provide a definition of topographic layout quality, which is one more step towards a comprehensive definition of diagram quality as such. Both metrics are shown to be objectively applicable. We quantify...

Barriers and limitations during implementation of the surgical safety checklist of the World Health Organization

Directory of Open Access Journals (Sweden)

Rosa Amalia Arboleda

2014-04-01

Full Text Available Introduction: The surgical safety checklist of the World Health Organization (WHO is a tool that checks and evaluates each procedure in the operating room. Despite its demonstrated effectiveness, it has many limitations and barriers to its implementation. The aim of this article was to present the current evidence regarding limitations and barriers to achieve a successful implementation of the surgical safety WHO checklist. Methods: A narrative review was designed. We performed a systematic literature search in PubMed/MEDLINE. Articles that describe or present as primary or secondary endpoints barriers or limitations during the implementation of the checklist WHO were selected. Observational or experimental articles were included from the date of the official launch of the WHO list. To describe the data a summary table was designed. Detailed results were organized qualitatively extracting the most prevalent limitations. Results: 17 studies were included in the final review process. The main findings were: 1 a large number of constraints reported in the literature that hinder the implementation process, 2 limitations were grouped into 9 categories according to their similarities and 3 the most frequently reported category was “knowledge”. Discussion: There are several factors that limit the proper implementation of the surgical safety checklist WHO. Among these, cultural factors, knowledge, indifference and / or relevance, communication, filling completeness, among others. Effective implementation strategies would reach its successful implementation.

Roundhouse Diagrams.

Science.gov (United States)

Ward, Robin E.; Wandersee, James

2000-01-01

Students must understand key concepts through reasoning, searching out related concepts, and making connections within multiple systems to learn science. The Roundhouse diagram was developed to be a concise, holistic, graphic representation of a science topic, process, or activity. Includes sample Roundhouse diagrams, a diagram checklist, and…

Improving safety culture in hospitals: Facilitators and barriers to implementation of Systemic Falls Investigative Method (SFIM).

Science.gov (United States)

Zecevic, Aleksandra A; Li, Alvin Ho-Ting; Ngo, Charity; Halligan, Michelle; Kothari, Anita

2017-06-01

The purpose of this study was to assess the facilitators and barriers to implementation of the Systemic Falls Investigative Method (SFIM) on selected hospital units. A cross-sectional explanatory mixed methods design was used to converge results from a standardized safety culture survey with themes that emerged from interviews and focus groups. Findings were organized by six elements of the Ottawa Model of Research Use framework. A geriatric rehabilitation unit of an acute care hospital and a neurological unit of a rehabilitation hospital were selected purposefully due to the high frequency of falls. Hospital staff who took part in: surveys (n = 39), interviews (n = 10) and focus groups (n = 12), and 38 people who were interviewed during falls investigations: fallers, family, unit staff and hospital management. Implementation of the SFIM to investigate fall occurrences. Percent of positive responses on the Modified Stanford Patient Safety Culture Survey Instrument converged with qualitative themes on facilitators and barriers for intervention implementation. Both hospital units had an overall poor safety culture which hindered intervention implementation. Facilitators were hospital accreditation, strong emphasis on patient safety, infrastructure and dedicated champions. Barriers included heavy workloads, lack of time, lack of resources and poor communication. Successful implementation of SFIM requires regulatory and organizational support, committed frontline staff and allocation of resources to identify active causes and latent contributing factors to falls. System-wide adjustments show promise for promotion of safety culture in hospitals where falls happen regularly. © The Author 2017. Published by Oxford University Press in association with the International Society for Quality in Health Care. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com

Nurse-physician communication in the long-term care setting: perceived barriers and impact on patient safety.

Science.gov (United States)

Tjia, Jennifer; Mazor, Kathleen M; Field, Terry; Meterko, Vanessa; Spenard, Ann; Gurwitz, Jerry H

2009-09-01

Clear and complete communication between health care providers is a prerequisite for safe patient management and is a major priority of the Joint Commission's 2008 National Patient Safety Goals. The goal of this study was to describe nurses' perceptions of nurse-physician communication in the long-term care (LTC) setting. Mixed-method study including a self-administered questionnaire and qualitative semistructured telephone interviews of licensed nurses from 26 LTC facilities in Connecticut. The questionnaire measured perceived openness to communication, mutual understanding, language comprehension, frustration, professional respect, nurse preparedness, time burden, and logistical barriers. Qualitative interviews focused on identifying barriers to effective nurse-physician communication that may not have previously been considered and eliciting nurses' recommendations for overcoming those barriers. Three hundred seventy-five nurses completed the questionnaire, and 21 nurses completed qualitative interviews. Nurses identified several barriers to effective nurse-physician communication: lack of physician openness to communication, logistic challenges, lack of professionalism, and language barriers. Feeling hurried by the physician was the most frequent barrier (28%), followed by finding a quiet place to call (25%), and difficulty reaching the physician (21%). In qualitative interviews, there was consensus that nurses needed to be brief and prepared with relevant clinical information when communicating with physicians and that physicians needed to be more open to listening. A combination of nurse and physician behaviors contributes to ineffective communication in the LTC setting. These findings have important implications for patient safety and support the development of structured communication interventions to improve quality of nurse-physician communication.

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips et al and Selby et al has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances, an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g., the top node). In the references cited above, the authors demonstrated the usefulness of influence diagrams for assessing the reliability of operator performance during pressurized thermal shock transients. In addition, the use of influence diagrams identified the critical variables that had the greatest impact on operator reliability for a particular scenario (e.g., control room design, procedures, etc.). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

MAPLE-X10 reactor safety assessment

International Nuclear Information System (INIS)

Cotnam, K.D.; Lounsbury, R.I.; Gillespie, G.E.

1990-01-01

This paper reports on the safety assessment of the 10 MW MAPLE-X10 reactor which has involved a substantial component of PSA analysis to supplement deterministic analysis. Initiating events are identified through the use of a master logic diagram. The events are then examined through event sequence diagrams, at the concept design stage, followed by a set of reliability analyses that are coordinated with the event sequence diagrams. Improvements identified through the reliability analyses are incorporated into the design to ensure that safety objectives are attained

Exploring Barriers to Medication Safety in an Ethiopian Hospital Emergency Department: A Human Factors Engineering Approach

Directory of Open Access Journals (Sweden)

Ephrem Abebe

2018-02-01

Full Text Available Objective: To describe challenges associated with the medication use process and potential medication safety hazards in an Ethiopian hospital emergency department using a human factors approach. Methods: We conducted a qualitative study employing observations and semi-structured interviews guided by the Systems Engineering Initiative for Patient Safety model of work system as an analytical framework. The study was conducted in the emergency department of a teaching hospital in Ethiopia. Study participants included resident doctors, nurses, and pharmacists. We performed content analysis of the qualitative data using accepted procedures. Results: Organizational barriers included communication failures, limited supervision and support for junior staff contributing to role ambiguity and conflict. Compliance with documentation policy was minimal. Task related barriers included frequent interruptions and work-related stress resulting from job requirements to continuously prioritize the needs of large numbers of patients and family members. Person related barriers included limited training and work experience. Work-related fatigue due to long working hours interfered with staff’s ability to document and review medication orders. Equipment breakdowns were common as were non-calibrated or poorly maintained medical devices contributing to erroneous readings. Key environment related barriers included overcrowding and frequent interruption of staff’s work. Cluttering of the work space compounded the problem by impeding efforts to locate medications, medical supplies or medical charts. Conclusions: Applying a systems based approach allows a context specific understanding of medication safety hazards in EDs from low-income countries. When developing interventions to improve medication and overall patient safety, health leaders should consider the interactions of the different factors. Conflict of Interest We declare no conflicts of interest or

Communication barriers in counselling foreign-language patients in public pharmacies: threats to patient safety?

Science.gov (United States)

Schwappach, David L B; Meyer Massetti, Carla; Gehring, Katrin

2012-10-01

Foreign-language (FL) patients are at increased risk for adverse drug events. Evidence regarding communication barriers and the safety of pharmaceutical care of FL patients in European countries is scarce despite large migrant populations. To investigate Swiss public pharmacists' experiences and current practices in counselling FL patients with a focus on patient safety. In a cross-sectional study heads of public pharmacies in Switzerland were surveyed using an electronic questionnaire. The survey assessed the frequency of communication barriers encountered in medication counselling of FL patients, perceptions of risks for adverse drug events, satisfaction with the quality of counselling provided to FL patients, current strategies to reduce risks, and preferences towards tools to improve safety for FL patients. 498 pharmacists completed the survey (43 % response rate). More than every second pharmacist reported at least weekly encounters at which they cannot provide good medication counselling to FL patients in the regional Swiss language. Ad-hoc interpreting by minors is also common at a considerable number of pharmacies (26.5 % reported at least one weekly occurrence). Approximately 10 % of pharmacies reported that they fail at least weekly to explain the essentials of drug therapy (e.g. dosing of children's medications) to FL patients. 79.8 % perceived the risk of FL patients for adverse drug events to be somewhat or much higher compared to other patients. 22.5 % of pharmacists reported being concerned at least monthly about medication safety when FL patients leave their pharmacy. However, the majority of pharmacists were satisfied with the quality of care provided to FL patients in their pharmacy [78.6 % (very) satisfied]. The main strategy used to improve counselling for FL patients was the employment of multilingual staff. Participants would use software for printing foreign-language labels (41.2 %) and multilingual package inserts (42.0 %) if these were

MORT User's Manual for use with the Management Oversight and Risk Tree analytical logic diagram. [Contains a list of System Safety Development Center publications

Energy Technology Data Exchange (ETDEWEB)

Knox, N.W.; Eicher, R.W.

1992-02-01

This report contains the User's Manual for MORT (Management Oversight and Risk Tree), a logic diagram in the form of a work sheet'' that illustrates a long series of interrelated questions. MORT is a comprehensive analytical procedure that provides a disciplined method for determining the causes and contributing factors of major accidents. Alternatively, it serves as a tool to evaluate the quality of an existing system. While similar in many respects to fault tree analysis, MORT is more generalized and presents over 1,500 specific elements of an ideal universal'' management program for optimizing environment, safety and health, and other programs. This User's Manual is intended to be used with the MORT diagram dated February 1992.

Bow tie methodology: a tool to enhance the visibility and understanding of nuclear safety cases

International Nuclear Information System (INIS)

Vannerem, Marc

2013-01-01

There is much common ground between the nuclear industry and other major hazard industries such as those subject to the Seveso II regulations, e.g. oil, gas and chemicals. They are all subject to legal requirements to identify and control hazards, and to demonstrate that all necessary measures have been taken to minimise risks posed by the site with regard to people and the environment. This places a requirement on the Operators of major hazard installations, whether nuclear or conventional, to understand and identify the hazards of their operations, the initiating events, the consequences, the prevention and mitigation measures. However, in the UK, nuclear and 'Seveso' type facilities seem to adopt a different approach to the presentation of their safety cases. Given the magnitude of the hazards, safety cases developed for nuclear fuel cycle facilities are rigorous, detailed and complex, which can have the effect of reducing the visibility of the key hazards and corresponding protective measures. In contrast, on installations in the oil and gas and chemical industries, a real attempt has been made over recent years to improve the visibility and accessibility of the safety case to all operating personnel, through the use of visual aids / diagrams. In particular, many Operators are choosing to use 'bow tie methodology', in which very simple overview diagrams are produced to illustrate, in a form understandable by all: - what the key hazards are; - the initiating events; - the consequences of an incident; - the barriers or 'Layers of Protection' which prevent an initiating event from developing into an incident; - the barriers or 'Layers of Defence' which mitigate the consequences of an incident, i.e. which prevent the incident from escalating into major consequences. The bow tie method is one of a number of methodologies that can be used to make safety cases more accessible. It is used in this paper to illustrate ways to

Promoters and Barriers to Implementation of Tracheal Intubation Airway Safety Bundle: A Mixed-Method Analysis.

Science.gov (United States)

Finn Davis, Katherine; Napolitano, Natalie; Li, Simon; Buffman, Hayley; Rehder, Kyle; Pinto, Matthew; Nett, Sholeen; Jarvis, J Dean; Kamat, Pradip; Sanders, Ronald C; Turner, David A; Sullivan, Janice E; Bysani, Kris; Lee, Anthony; Parker, Margaret; Adu-Darko, Michelle; Giuliano, John; Biagas, Katherine; Nadkarni, Vinay; Nishisaki, Akira

2017-10-01

To describe promoters and barriers to implementation of an airway safety quality improvement bundle from the perspective of interdisciplinary frontline clinicians and ICU quality improvement leaders. Mixed methods. Thirteen PICUs of the National Emergency Airway Registry for Children network. Remote or on-site focus groups with interdisciplinary ICU staff. Two semistructured interviews with ICU quality improvement leaders with quantitative and qualitative data-based feedbacks. Bundle implementation success (compliance) was defined as greater than or equal to 80% use for tracheal intubations for 3 consecutive months. ICUs were classified as early or late adopters. Focus group discussions concentrated on safety concerns and promoters and barriers to bundle implementation. Initial semistructured quality improvement leader interviews assessed implementation tactics and provided recommendations. Follow-up interviews assessed degree of acceptance and changes made after initial interview. Transcripts were thematically analyzed and contrasted by early versus late adopters. Median duration to achieve success was 502 days (interquartile range, 182-781). Five sites were early (median, 153 d; interquartile range, 146-267) and eight sites were late adopters (median, 783 d; interquartile range, 773-845). Focus groups identified common "promoter" themes-interdisciplinary approach, influential champions, and quality improvement bundle customization-and "barrier" themes-time constraints, competing paperwork and quality improvement activities, and poor engagement. Semistructured interviews with quality improvement leaders identified effective and ineffective tactics implemented by early and late adopters. Effective tactics included interdisciplinary quality improvement team involvement (early adopter: 5/5, 100% vs late adopter: 3/8, 38%; p = 0.08); ineffective tactics included physician-only rollouts, lack of interdisciplinary education, lack of data feedback to frontline clinicians

Algorithmic phase diagrams

Science.gov (United States)

Hockney, Roger

1987-01-01

Algorithmic phase diagrams are a neat and compact representation of the results of comparing the execution time of several algorithms for the solution of the same problem. As an example, the recent results are shown of Gannon and Van Rosendale on the solution of multiple tridiagonal systems of equations in the form of such diagrams. The act of preparing these diagrams has revealed an unexpectedly complex relationship between the best algorithm and the number and size of the tridiagonal systems, which was not evident from the algebraic formulae in the original paper. Even so, for a particular computer, one diagram suffices to predict the best algorithm for all problems that are likely to be encountered the prediction being read directly from the diagram without complex calculation.

Involvement of patients with cancer in patient safety: a qualitative study of current practices, potentials and barriers.

Science.gov (United States)

Martin, Helle Max; Navne, Laura Emdal; Lipczak, Henriette

2013-10-01

Patient involvement in patient safety is widely advocated but knowledge regarding implementation of the concept in clinical practice is sparse. To investigate existing practices for patient involvement in patient safety, and opportunities and barriers for further involvement. A qualitative study of patient safety involvement practices in patient trajectories for prostate, uterine and colorectal cancer in Denmark. Observations from four hospital wards and interviews with 25 patients with cancer, 11 hospital doctors, 10 nurses, four general practitioners and two private practicing gynaecologists were conducted using ethnographic methodology. Patient safety was not a topic of attention for patients or dominant in communication between patients and healthcare professionals. The understanding of patient safety in clinical practice is almost exclusively linked to disease management. Involvement of patients is not systematic, but healthcare professionals and patients express willingness to engage. Invitation and encouragement of patients to become involved could be further systematised and developed. Barriers include limited knowledge of patient safety, of specific patient safety involvement techniques and concern regarding potential negative impact on doctor-patient relationship. Involvement of patients in patient safety must take into account that despite stated openness to the idea of involvement, patients and health professionals may not in practice show immediate concern. Lack of systematic involvement can also be attributed to limited knowledge about how to implement involvement beyond the focus of self-monitoring and compliance and a concern about the consequences of patient involvement for treatment outcomes. To realise the potential of patients' and health professionals' shared openness towards involvement, there is a need for more active facilitation and concrete guidance on how involvement can be practiced by both parties.

A multicentre, randomised, controlled trial to assess the safety, ease of use, and reliability of hyaluronic acid/carboxymethylcellulose powder adhesion barrier versus no barrier in colorectal laparoscopic surgery.

Science.gov (United States)

Berdah, Stéphane V; Mariette, Christophe; Denet, Christine; Panis, Yves; Laurent, Christophe; Cotte, Eddy; Huten, Nöel; Le Peillet Feuillet, Eliane; Duron, Jean-Jacques

2014-10-27

Intra-peritoneal adhesions are frequent following abdominal surgery and are the most common cause of small bowel obstructions. A hyaluronic acid/carboxymethylcellulose (HA/CMC) film adhesion barrier has been shown to reduce adhesion formation in abdominal surgery. An HA/CMC powder formulation was developed for application during laparoscopic procedures. This was an exploratory, prospective, randomised, single-blind, parallel-group, Phase IIIb, multicentre study conducted at 15 hospitals in France to assess the safety of HA/CMC powder versus no adhesion barrier following laparoscopic colorectal surgery. Subjects ≥18 years of age who were scheduled for colorectal laparoscopy (Mangram contamination class I‒III) within 8 weeks of selection were eligible, regardless of aetiology. Participants were randomised 1:1 to the HA/CMC powder or no adhesion barrier group using a centralised randomisation list. Patients assigned to HA/CMC powder received a single application of 1 to 10 g on adhesion-prone areas. In the no adhesion barrier group, no adhesion barrier or placebo was applied. The primary safety assessments were the incidence of adverse events, serious adverse events, and surgical site infections (SSIs) for 30 days following surgery. Between-group comparisons were made using Fisher's exact test. Of those randomised to the HA/CMC powder (n = 105) or no adhesion barrier (n = 104) groups, one patient in each group discontinued prior to the study end (one death in each group). Adverse events were more frequent in the HA/CMC powder group versus the no adhesion barrier group (63% vs. 39%; P barrier group in SSIs (21% vs. 14%; P = 0.216) and serious SSIs (12% vs. 9%; P = 0.38), or in the most frequent serious SSIs of pelvic abscess (5% and 2%; significance not tested), anastomotic fistula (3% and 4%), and peritonitis (2% and 3%). This exploratory study found significantly higher rates of adverse events and serious adverse events in the HA/CMC powder group compared with

Barriers to Construction Health and Safety Self-regulation: A Scoping Case of Nigeria

Directory of Open Access Journals (Sweden)

Umeokafor Nnedinma

2017-03-01

Full Text Available This scoping study builds on the recent uncovering that in terms of health and safety (H&S, the Nigerian construction industry is self-regulated in various forms, not unregulated and that the size of company can further explain H&S self-regulation. Consequently, the barriers identified through literature review were assessed using questionnaires. Analysis of the data collected from construction practitioners in Nigeria shows that ‘economic factors’ mostly explains the barriers to construction H&S self-regulation. This is followed by the ‘ability to self-regulate’ and ‘lack of awareness’. Furthermore, the results show significant differences among small, medium and large construction contractors on seven factors of which include ‘normative case’ factors, ‘H&S is a duty’, ‘H&S is the right thing’ and ‘unfair H&S standards or legislation’. Although a scoping study, the study draws attention to the barriers to construction H&S self-regulation in Nigeria and demonstrates an alternative to state regulation of H&S.

Safety assurance logic techniques for evaluation of accident prevention and mitigation

International Nuclear Information System (INIS)

McWethy, L.M.; Hagan, J.W.

1976-01-01

Safety assurance methods have been developed and applied in reactor safety assessments of FFTF. These methods promote visibility of the total safety provided by the plant, both in prevention of off-normal or accident conditions as well as provision of various features which terminate conditions within acceptable bounds if such conditions should occur. One of the primary techniques applied in safety assurance is the development of safety assurance diagrams. These diagrams explicitly identify the multiple lines of defense which prevent accident progression. The diagrams graphically demonstrate the defense-in-depth provided by the plant for each postulated occurrence. Lines of defense are shown against ever having an occurrence in the first place; thus giving appropriate emphasis on accident prevention, and visibility to the designer's role in promoting this level of safety. These diagrams, or accident process trees, also show graphically the various paths of postulated accident progression to their logical termination. Evaluation of the importance and strength of each line-of-defense assures fulfillment of the safety objectives of the overall plant system

The development of an audit technique to assess the quality of safety barrier management

International Nuclear Information System (INIS)

Guldenmund, Frank; Hale, Andrew; Goossens, Louis; Betten, Jeroen; Duijm, Nijs Jan

2006-01-01

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed

The development of an audit technique to assess the quality of safety barrier management

Energy Technology Data Exchange (ETDEWEB)

Guldenmund, Frank [Safety Science Group, Delft University of Technology (Netherlands)]. E-mail: f.w.guldenmund@tbm.tudelft.nl; Hale, Andrew [Safety Science Group, Delft University of Technology (Netherlands); Goossens, Louis [Safety Science Group, Delft University of Technology (Netherlands); Betten, Jeroen [Safety Science Group, Delft University of Technology (Netherlands); Duijm, Nijs Jan [Riso National Laboratory (Denmark)

2006-03-31

This paper describes the development of a management model to control barriers devised to prevent major hazard scenarios. Additionally, an audit technique is explained that assesses the quality of such a management system. The final purpose of the audit technique is to quantify those aspects of the management system that have a direct impact on the reliability and effectiveness of the barriers and, hence, the probability of the scenarios involved. First, an outline of the management model is given and its elements are explained. Then, the development of the audit technique is described. Because the audit technique uses actual major hazard scenarios and barriers within these as its focus, the technique achieves a concreteness and clarity that many other techniques often lack. However, this strength is also its limitation, since the full safety management system is not covered with the technique. Finally, some preliminary experiences obtained from several test sites are compiled and discussed.

Viral pathogenesis in diagrams

National Research Council Canada - National Science Library

Tremblay, Michel; Berthiaume, Laurent; Ackermann, Hans-Wolfgang

2001-01-01

.... The 268 diagrams in Viral Pathogenesis in Diagrams were selected from over 800 diagrams of English and French virological literature, including one derived from a famous drawing by Leonardo da Vinci...

Identifying Facilitators and Barriers for Patient Safety in a Medicine Label Design System Using Patient Simulation and Interviews

DEFF Research Database (Denmark)

Dieckmann, Peter; Clemmensen, Marianne Hald; Sørensen, Trine Kart

2016-01-01

Objectives Medicine label design plays an important role in improving patient safety. This study aimed at identifying facilitators and barriers in a medicine label system to prevent medication errors in clinical use by health care professionals. Methods The study design is qualitative and explora......Objectives Medicine label design plays an important role in improving patient safety. This study aimed at identifying facilitators and barriers in a medicine label system to prevent medication errors in clinical use by health care professionals. Methods The study design is qualitative...... of the system and some inconsistencies (different meaning of colors) posed challenges, when considered with the actual application context, in which there is little time to get familiar with the design features. Conclusions For optimizing medicine labels and obtaining the full benefit of label design features...

Removing bridge barriers stimulates suicides: an unfortunate natural experiment.

Science.gov (United States)

Beautrais, Annette L; Gibb, Sheree J; Fergusson, David M; Horwood, L John; Larkin, Gregory Luke

2009-06-01

Safety barriers to prevent suicide by jumping were removed from Grafton Bridge in Auckland, New Zealand, in 1996 after having been in place for 60 years. This study compared the number of suicides due to jumping from the bridge after the reinstallation of safety barriers in 2003. National mortality data for suicide deaths were compared for three time periods: 1991-1995 (old barrier in place); 1997-2002 (no barriers in place); 2003-2006 (after barriers were reinstated). Removal of barriers was followed by a fivefold increase in the number and rate of suicides from the bridge. These increases led to a decision to reinstall safety barriers. Since the reinstallation of barriers, of an improved design, in 2003, there have been no suicides from the bridge. This natural experiment, using a powerful a-b-a (reversal) design, shows that safety barriers are effective in preventing suicide: their removal increases suicides; their reinstatement prevents suicides.

Diagram, a Learning Environment for Initiation to Object-Oriented Modeling with UML Class Diagrams

Science.gov (United States)

Py, Dominique; Auxepaules, Ludovic; Alonso, Mathilde

2013-01-01

This paper presents Diagram, a learning environment for object-oriented modelling (OOM) with UML class diagrams. Diagram an open environment, in which the teacher can add new exercises without constraints on the vocabulary or the size of the diagram. The interface includes methodological help, encourages self-correcting and self-monitoring, and…

VennDiagram: a package for the generation of highly-customizable Venn and Euler diagrams in R

Directory of Open Access Journals (Sweden)

Boutros Paul C

2011-01-01

Full Text Available Abstract Background Visualization of orthogonal (disjoint or overlapping datasets is a common task in bioinformatics. Few tools exist to automate the generation of extensively-customizable, high-resolution Venn and Euler diagrams in the R statistical environment. To fill this gap we introduce VennDiagram, an R package that enables the automated generation of highly-customizable, high-resolution Venn diagrams with up to four sets and Euler diagrams with up to three sets. Results The VennDiagram package offers the user the ability to customize essentially all aspects of the generated diagrams, including font sizes, label styles and locations, and the overall rotation of the diagram. We have implemented scaled Venn and Euler diagrams, which increase graphical accuracy and visual appeal. Diagrams are generated as high-definition TIFF files, simplifying the process of creating publication-quality figures and easing integration with established analysis pipelines. Conclusions The VennDiagram package allows the creation of high quality Venn and Euler diagrams in the R statistical environment.

VennDiagram: a package for the generation of highly-customizable Venn and Euler diagrams in R.

Science.gov (United States)

Chen, Hanbo; Boutros, Paul C

2011-01-26

Visualization of orthogonal (disjoint) or overlapping datasets is a common task in bioinformatics. Few tools exist to automate the generation of extensively-customizable, high-resolution Venn and Euler diagrams in the R statistical environment. To fill this gap we introduce VennDiagram, an R package that enables the automated generation of highly-customizable, high-resolution Venn diagrams with up to four sets and Euler diagrams with up to three sets. The VennDiagram package offers the user the ability to customize essentially all aspects of the generated diagrams, including font sizes, label styles and locations, and the overall rotation of the diagram. We have implemented scaled Venn and Euler diagrams, which increase graphical accuracy and visual appeal. Diagrams are generated as high-definition TIFF files, simplifying the process of creating publication-quality figures and easing integration with established analysis pipelines. The VennDiagram package allows the creation of high quality Venn and Euler diagrams in the R statistical environment.

Introduction to Feynman diagrams

CERN Document Server

Bilenky, Samoil Mikhelevich

1974-01-01

Introduction to Feynman Diagrams provides Feynman diagram techniques and methods for calculating quantities measured experimentally. The book discusses topics Feynman diagrams intended for experimental physicists. Topics presented include methods for calculating the matrix elements (by perturbation theory) and the basic rules for constructing Feynman diagrams; techniques for calculating cross sections and polarizations; processes in which both leptons and hadrons take part; and the electromagnetic and weak form factors of nucleons. Experimental physicists and graduate students of physics will

Pourbaix Diagrams at Elevated Temperatures A Study of Zinc and Tin

Science.gov (United States)

Palazhchenko, Olga

Metals in industrial settings such as power plants are often subjected to high temperature and pressure aqueous environments, where failure to control corrosion compromises worker and environment safety. For instance, zircaloy (1.2-1.7 wt.% Sn) fuel rods are exposed to aqueous 250-310 °C coolant in CANDU reactors. The Pourbaix (EH-pH) diagram is a plot of electrochemical potential versus pH, which shows the domains of various metal species and by inference, corrosion susceptibility. Elevated temperature data for tin +II and tin +IV species were obtained using solid-aqueous phase equilibria with the respective oxides, in a batch vessel with in-situ pH measurement. Solubilities, determined via spectroscopic techniques, were used to calculate equilibrium constants and the Gibbs energies of Sn complexes for E-pH diagram construction. The SnOH3+ and Sn(OH )-5 species were incorporated, for the first time, into the 298.15 K and 358.15 K diagrams, with novel Go values determined at 358.15 K. Key words: Pourbaix diagrams, EH-pH, elevated temperatures, solubility, equilibrium, metal oxides, hydrolysis, redox potential, pH, thermochemical data, tin, zinc, zircaloy, corrosion, passivity.

Diagrams benefit symbolic problem-solving.

Science.gov (United States)

Chu, Junyi; Rittle-Johnson, Bethany; Fyfe, Emily R

2017-06-01

The format of a mathematics problem often influences students' problem-solving performance. For example, providing diagrams in conjunction with story problems can benefit students' understanding, choice of strategy, and accuracy on story problems. However, it remains unclear whether providing diagrams in conjunction with symbolic equations can benefit problem-solving performance as well. We tested the impact of diagram presence on students' performance on algebra equation problems to determine whether diagrams increase problem-solving success. We also examined the influence of item- and student-level factors to test the robustness of the diagram effect. We worked with 61 seventh-grade students who had received 2 months of pre-algebra instruction. Students participated in an experimenter-led classroom session. Using a within-subjects design, students solved algebra problems in two matched formats (equation and equation-with-diagram). The presence of diagrams increased equation-solving accuracy and the use of informal strategies. This diagram benefit was independent of student ability and item complexity. The benefits of diagrams found previously for story problems generalized to symbolic problems. The findings are consistent with cognitive models of problem-solving and suggest that diagrams may be a useful additional representation of symbolic problems. © 2017 The British Psychological Society.

Teams, tribes and patient safety: overcoming barriers to effective teamwork in healthcare.

Science.gov (United States)

Weller, Jennifer; Boyd, Matt; Cumin, David

2014-03-01

Modern healthcare is delivered by multidisciplinary, distributed healthcare teams who rely on effective teamwork and communication to ensure effective and safe patient care. However, we know that there is an unacceptable rate of unintended patient harm, and much of this is attributed to failures in communication between health professionals. The extensive literature on teams has identified shared mental models, mutual respect and trust and closed-loop communication as the underpinning conditions required for effective teams. However, a number of challenges exist in the healthcare environment. We explore these in a framework of educational, psychological and organisational challenges to the development of effective healthcare teams. Educational interventions can promote a better understanding of the principles of teamwork, help staff understand each other's roles and perspectives, and help develop specific communication strategies, but may not be sufficient on their own. Psychological barriers, such as professional silos and hierarchies, and organisational barriers such as geographically distributed teams, can increase the chance of communication failures with the potential for patient harm. We propose a seven-step plan to overcome the barriers to effective team communication that incorporates education, psychological and organisational strategies. Recent evidence suggests that improvement in teamwork in healthcare can lead to significant gains in patient safety, measured against efficiency of care, complication rate and mortality. Interventions to improve teamwork in healthcare may be the next major advance in patient outcomes.

Safety evaluation methodology of engineering barriers at repository for low and intermediate level radioactive waste

International Nuclear Information System (INIS)

Zarnic, R.; Bokan Bosiljkov, V.; Giacomelli, M.

2007-01-01

Analyses of the roles of cement-based barriers in radioactive waste isolation show that models used to estimate their characteristics during the lifetime of the repository must consider the alteration of material properties with time due to degradation processes. Reinforced concrete barriers at repositories shall be designed in such manner that they fulfil besides isolative capabilities also the required functions of mechanical resistance and stability. Key elements of safety evaluation are mainly the correct selection of materials for mineral composites with cement binder (cements, aggregates, mineral additives and chemical admixtures) and their design, execution of construction works and production of precast concrete containers (continuous casting of concrete - no cold joints, limited number of construction joints, proper placing and consolidation, finishing and curing), strict control of used materials and inspection of works, as well as investigation after the construction (visual inspection, non-destructive testing, monitoring, ageing assessment on test containers). According to the methodology presented in this paper the lifetime of the repository can be estimated and, if shorter than 300 years or shorter than the period resulting from safety analysis, appropriate corrective measures shall be taken. (author)

Facilitators and barriers of implementing enhanced recovery in colorectal surgery at a safety net hospital: A provider and patient perspective.

Science.gov (United States)

Alawadi, Zeinab M; Leal, Isabel; Phatak, Uma R; Flores-Gonzalez, Juan R; Holihan, Julie L; Karanjawala, Burzeen E; Millas, Stefanos G; Kao, Lillian S

2016-03-01

Enhanced Recovery After Surgery (ERAS) pathways are known to decrease complications and duration of stay in colorectal surgery patients. However, it is unclear whether an ERAS pathway would be feasible and effective at a safety-net hospital. The aim of this study was to identify local barriers and facilitators before the adoption of an ERAS pathway for patients undergoing colorectal operations at a safety-net hospital. Semistructured interviews were conducted to assess the perceived barriers and facilitators before ERAS adoption. Stratified purposive sampling was used. Interviews were audiotaped, transcribed verbatim, and analyzed using content analysis. Analytic and investigator triangulation were used to establish credibility. Interviewees included 8 anesthesiologists, 5 surgeons, 6 nurses, and 18 patients. Facilitators identified across the different medical professions were (1) feasibility and alignment with current practice, (2) standardization of care, (3) smallness of community, (4) good teamwork and communication, and (5) caring for patients. The barriers were (1) difficulty in adapting to change, (2) lack of coordination between different departments, (3) special needs of a highly comorbid and socioeconomically disadvantaged patient population, (4) limited resources, and (5) rotating residents. Facilitators identified by the patients were (1) welcoming a speedy recovery, (2) being well-cared for and satisfied with treatment, (3) adequate social support, (4) welcoming early mobilization, and (5) effective pain management. The barriers were (1) lack of quiet and private space, (2) need for more patient education and counseling, and (3) unforeseen complications. Although limited hospital resources are perceived as a barrier to ERAS implementation at a safety-net hospital, there is strong support for such pathways and multiple factors were identified that may facilitate change. Inclusion of patient perspectives is critical to identifying challenges and

Addressing safety liabilities of TfR bispecific antibodies that cross the blood-brain barrier.

Science.gov (United States)

Couch, Jessica A; Yu, Y Joy; Zhang, Yin; Tarrant, Jacqueline M; Fuji, Reina N; Meilandt, William J; Solanoy, Hilda; Tong, Raymond K; Hoyte, Kwame; Luk, Wilman; Lu, Yanmei; Gadkar, Kapil; Prabhu, Saileta; Ordonia, Benjamin A; Nguyen, Quyen; Lin, Yuwen; Lin, Zhonghua; Balazs, Mercedesz; Scearce-Levie, Kimberly; Ernst, James A; Dennis, Mark S; Watts, Ryan J

2013-05-01

Bispecific antibodies using the transferrin receptor (TfR) have shown promise for boosting antibody uptake in brain. Nevertheless, there are limited data on the therapeutic properties including safety liabilities that will enable successful development of TfR-based therapeutics. We evaluate TfR/BACE1 bispecific antibody variants in mouse and show that reducing TfR binding affinity improves not only brain uptake but also peripheral exposure and the safety profile of these antibodies. We identify and seek to address liabilities of targeting TfR with antibodies, namely, acute clinical signs and decreased circulating reticulocytes observed after dosing. By eliminating Fc effector function, we ameliorated the acute clinical signs and partially rescued a reduction in reticulocytes. Furthermore, we show that complement mediates a residual decrease in reticulocytes observed after Fc effector function is eliminated. These data raise important safety concerns and potential mitigation strategies for the development of TfR-based therapies that are designed to cross the blood-brain barrier.

Optimizing UML Class Diagrams

Directory of Open Access Journals (Sweden)

Sergievskiy Maxim

2018-01-01

Full Text Available Most of object-oriented development technologies rely on the use of the universal modeling language UML; class diagrams play a very important role in the design process play, used to build a software system model. Modern CASE tools, which are the basic tools for object-oriented development, can’t be used to optimize UML diagrams. In this manuscript we will explain how, based on the use of design patterns and anti-patterns, class diagrams could be verified and optimized. Certain transformations can be carried out automatically; in other cases, potential inefficiencies will be indicated and recommendations given. This study also discusses additional CASE tools for validating and optimizing of UML class diagrams. For this purpose, a plugin has been developed that analyzes an XMI file containing a description of class diagrams.

Treatment of barrier evolution: the SKB perspective

International Nuclear Information System (INIS)

Hedin, A.

2002-01-01

This paper serves as a point of departure for the discussions to be held within the Working Group of Technical Topic entitled 'Barriers and System Performances within a safety case: Their functioning and Evolution with Time'. The paper gives the SKB perspective of the issues to be discussed within the Working Group for this Topic. The following issues to be discussed by the Working Group are: What is the role of each barrier as a function of time or in the different time frames? What is its contribution to the overall system performance or safety as a function of time? Which are the main uncertainties on the performance of barriers in the timescales? To what extent should we enhance the robustness of barriers because of the uncertainties of some component behaviour with time? What is the requested or required performance versus the expected or realistic or conservative behaviour with time? How are these safety margins used as arguments in a safety case? What is the issue associated with the geosphere stability for different geological systems? How is barriers and system performances as a function of time evaluated (and presented and communicated) in a safety case? What kind of measures are used for siting, designing and optimising robust barriers corresponding to situations that can vary with time? Are human actions considered to be relevant? (authors)

Stage line diagram: An age-conditional reference diagram for tracking development

NARCIS (Netherlands)

Buuren, S. van; Ooms, J.C.L.

2009-01-01

This paper presents a method for calculating stage line diagrams, a novel type of reference diagram useful for tracking developmental processes over time. Potential fields of applications include: dentistry (tooth eruption), oncology (tumor grading, cancer staging), virology (HIV infection and

Stage line diagram: an age-conditional reference diagram for tracking development.

NARCIS (Netherlands)

Van Buuren, S.; Ooms, J.C.L.

2009-01-01

This paper presents a method for calculating stage line diagrams, a novel type of reference diagram useful for tracking developmental processes over time. Potential fields of applications include: dentistry (tooth eruption), oncology (tumor grading, cancer staging), virology (HIV infection and

CERPHASE: Computer-generated phase diagrams

International Nuclear Information System (INIS)

Ruys, A.J.; Sorrell, C.C.; Scott, F.H.

1990-01-01

CERPHASE is a collection of computer programs written in the programming language basic and developed for the purpose of teaching the principles of phase diagram generation from the ideal solution model of thermodynamics. Two approaches are used in the generation of the phase diagrams: freezing point depression and minimization of the free energy of mixing. Binary and ternary phase diagrams can be generated as can diagrams containing the ideal solution parameters used to generate the actual phase diagrams. Since the diagrams generated utilize the ideal solution model, data input required from the operator is minimal: only the heat of fusion and melting point of each component. CERPHASE is menu-driven and user-friendly, containing simple instructions in the form of screen prompts as well as a HELP file to guide the operator. A second purpose of CERPHASE is in the prediction of phase diagrams in systems for which no experimentally determined phase diagrams are available, enabling the estimation of suitable firing or sintering temperatures for otherwise unknown systems. Since CERPHASE utilizes ideal solution theory, there are certain limitations imposed on the types of systems that can be predicted reliably. 6 refs., 13 refs

The Food Safety Modernization Act: a barrier to trade? Only if the science says so.

Science.gov (United States)

McNeill, Naomi

2012-01-01

The Food Safety Modernization Act improves oversight of America's food safety system. Title III, which regulates imported food, may create extra burdens for importers and therefore act as a barrier to trade. What will be on trial before the World Trade Organization (WTO), however, is not the law's content, but the science supporting it. Under the WTO regime, food safety laws that could restrict the free movement of food commodities must be sufficiently justified by scientific evidence. Member states must engage in risk assessments and regulate food imports in a manner that is "no more restrictive than necessary" to protect against the health risks identified by scientific evidence. This article examines the requirements of the WTO to evaluate the FSMA's legality under WTO rules. It analyzes the case law of the WTO Panel and Appellate Body and compares the FMSA to the EU's General Food Law.

Synergistic effects of the safety factor and shear flows on development of internal transport barriers in reversed shear plasmas

International Nuclear Information System (INIS)

Wang, A.K.; Dong, J.Q.; Qu, W.X.; Qiu, X.M.

2002-01-01

A new suppression mechanism of turbulent transport, characteristic of the synergism between safety factor and shear flows, is proposed to explain the internal transport barriers (ITBs) observed in neutral-beam-heated tokamak discharges with reversed magnetic shear. It is shown that the evolution of turbulent transport with the strength of the suppression mechanism reproduces the basic features of the formation and development of ITBs observed in experiments. In addition, the present analyses predict the possibility of global ion and electron heat transport barriers

Para-equilibrium phase diagrams

International Nuclear Information System (INIS)

Pelton, Arthur D.; Koukkari, Pertti; Pajarre, Risto; Eriksson, Gunnar

2014-01-01

Highlights: • A rapidly cooled system may attain a state of para-equilibrium. • In this state rapidly diffusing elements reach equilibrium but others are immobile. • Application of the Phase Rule to para-equilibrium phase diagrams is discussed. • A general algorithm to calculate para-equilibrium phase diagrams is described. - Abstract: If an initially homogeneous system at high temperature is rapidly cooled, a temporary para-equilibrium state may result in which rapidly diffusing elements have reached equilibrium but more slowly diffusing elements have remained essentially immobile. The best known example occurs when homogeneous austenite is quenched. A para-equilibrium phase assemblage may be calculated thermodynamically by Gibbs free energy minimization under the constraint that the ratios of the slowly diffusing elements are the same in all phases. Several examples of calculated para-equilibrium phase diagram sections are presented and the application of the Phase Rule is discussed. Although the rules governing the geometry of these diagrams may appear at first to be somewhat different from those for full equilibrium phase diagrams, it is shown that in fact they obey exactly the same rules with the following provision. Since the molar ratios of non-diffusing elements are the same in all phases at para-equilibrium, these ratios act, as far as the geometry of the diagram is concerned, like “potential” variables (such as T, pressure or chemical potentials) rather than like “normal” composition variables which need not be the same in all phases. A general algorithm to calculate para-equilibrium phase diagrams is presented. In the limit, if a para-equilibrium calculation is performed under the constraint that no elements diffuse, then the resultant phase diagram shows the single phase with the minimum Gibbs free energy at any point on the diagram; such calculations are of interest in physical vapor deposition when deposition is so rapid that phase

A prospective, randomized, multicenter, controlled study of the safety of Seprafilm adhesion barrier in abdominopelvic surgery of the intestine.

NARCIS (Netherlands)

Beck, D.E.; Cohen, Z.; Fleshman, J.W.; Kaufman, H.S.; Goor, H. van; Wolff, B.G.

2003-01-01

INTRODUCTION: Seprafilm adhesion barrier (Seprafilm) has been proven to prevent adhesion formation after abdominal and pelvic surgery. This article reports safety results, including the postoperative incidence of abdominal and pelvic abscess and pulmonary embolism, from a large, multicenter trial

Sintering diagrams of UO2

International Nuclear Information System (INIS)

Mohan, A.; Soni, N.C.; Moorthy, V.K.

1979-01-01

Ashby's method (see Acta Met., vol. 22, p. 275, 1974) of constructing sintering diagrams has been modified to obtain contribution diagrams directly from the computer. The interplay of sintering variables and mechanisms are studied and the factors that affect the participation of mechanisms in UO 2 are determined. By studying the physical properties, it emerges that the order of inaccuracies is small in most cases and do not affect the diagrams. On the other hand, even a 10% error in activation energies, which is quite plausible, would make a significant difference to the diagram. The main criticism of Ashby's approach is that the numerous properties and equations used, communicate their inaccuracies to the diagrams and make them unreliable. The present study has considerably reduced the number of factors that need to be refined to make the sintering diagrams more meaningful. (Auth.)

Feynman diagram drawing made easy

International Nuclear Information System (INIS)

Baillargeon, M.

1997-01-01

We present a drawing package optimised for Feynman diagrams. These can be constructed interactively with a mouse-driven graphical interface or from a script file, more suitable to work with a diagram generator. It provides most features encountered in Feynman diagrams and allows to modify every part of a diagram after its creation. Special attention has been paid to obtain a high quality printout as easily as possible. This package is written in Tcl/Tk and in C. (orig.)

The Semiotic Structure of Geometry Diagrams: How Textbook Diagrams Convey Meaning

Science.gov (United States)

Dimmel, Justin K.; Herbst, Patricio G.

2015-01-01

Geometry diagrams use the visual features of specific drawn objects to convey meaning about generic mathematical entities. We examine the semiotic structure of these visual features in two parts. One, we conduct a semiotic inquiry to conceptualize geometry diagrams as mathematical texts that comprise choices from different semiotic systems. Two,…

Stage line diagram: an age-conditional reference diagram for tracking development.

Science.gov (United States)

van Buuren, Stef; Ooms, Jeroen C L

2009-05-15

This paper presents a method for calculating stage line diagrams, a novel type of reference diagram useful for tracking developmental processes over time. Potential fields of applications include: dentistry (tooth eruption), oncology (tumor grading, cancer staging), virology (HIV infection and disease staging), psychology (stages of cognitive development), human development (pubertal stages) and chronic diseases (stages of dementia). Transition probabilities between successive stages are modeled as smoothly varying functions of age. Age-conditional references are calculated from the modeled probabilities by the mid-P value. It is possible to eliminate the influence of age by calculating standard deviation scores (SDS). The method is applied to the empirical data to produce reference charts on secondary sexual maturation. The mean of the empirical SDS in the reference population is close to zero, whereas the variance depends on age. The stage line diagram provides quick insight into both status (in SDS) and tempo (in SDS/year) of development of an individual child. Other measures (e.g. height SDS, body mass index SDS) from the same child can be added to the chart. Diagrams for sexual maturation are available as a web application at http://vps.stefvanbuuren.nl/puberty. The stage line diagram expresses status and tempo of discrete changes on a continuous scale. Wider application of these measures scores opens up new analytic possibilities. (c) 2009 John Wiley & Sons, Ltd.

Ring diagrams and phase transitions

International Nuclear Information System (INIS)

Takahashi, K.

1986-01-01

Ring diagrams at finite temperatures carry most infrared-singular parts among Feynman diagrams. Their effect to effective potentials are in general so significant that one must incorporate them as well as 1-loop diagrams. The author expresses these circumstances in some examples of supercooled phase transitions

Stereo 3D spatial phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Kang, Jinwu, E-mail: kangjw@tsinghua.edu.cn; Liu, Baicheng, E-mail: liubc@tsinghua.edu.cn

2016-07-15

Phase diagrams serve as the fundamental guidance in materials science and engineering. Binary P-T-X (pressure–temperature–composition) and multi-component phase diagrams are of complex spatial geometry, which brings difficulty for understanding. The authors constructed 3D stereo binary P-T-X, typical ternary and some quaternary phase diagrams. A phase diagram construction algorithm based on the calculated phase reaction data in PandaT was developed. And the 3D stereo phase diagram of Al-Cu-Mg ternary system is presented. These phase diagrams can be illustrated by wireframe, surface, solid or their mixture, isotherms and isopleths can be generated. All of these can be displayed by the three typical display ways: electronic shutter, polarization and anaglyph (for example red-cyan glasses). Especially, they can be printed out with 3D stereo effect on paper, and watched by the aid of anaglyph glasses, which makes 3D stereo book of phase diagrams come to reality. Compared with the traditional illustration way, the front of phase diagrams protrude from the screen and the back stretches far behind of the screen under 3D stereo display, the spatial structure can be clearly and immediately perceived. These 3D stereo phase diagrams are useful in teaching and research. - Highlights: • Stereo 3D phase diagram database was constructed, including binary P-T-X, ternary, some quaternary and real ternary systems. • The phase diagrams can be watched by active shutter or polarized or anaglyph glasses. • The print phase diagrams retains 3D stereo effect which can be achieved by the aid of anaglyph glasses.

Magnetization switching diagram of a perpendicular synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer

Energy Technology Data Exchange (ETDEWEB)

Koplak, O. [Immanuel Kant Baltic Federal University, 236041 Kaliningrad (Russian Federation); Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Talantsev, A. [Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Lu, Y.; Hamadeh, A.; Pirro, P.; Hauet, T. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine (France); Morgunov, R., E-mail: morgunov2005@yandex.ru [Institute of Problems of Chemical Physics, 142432 Chernogolovka, Moscow (Russian Federation); Tambov State Technical University, 392000 Tambov (Russian Federation); Mangin, S. [Institut Jean Lamour, UMR 7198 CNRS, Université de Lorraine (France)

2017-07-01

Highlights: • Anisotropy, Zeeman and exchange energy determine sequence of magnetic transitions. • Three temperature ranges manifest different shapes of the hysteresis loop. • The critical transition fields are temperature dependent. - Abstract: Magnetic configurations in synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer with strong perpendicular anisotropy have been systematically studied. Magnetization versus field hysteresis loop has been measured for different temperature ranging from 5 to 300 K. The applied field – temperature (H-T) magnetization switching diagram has been constructed by extracting the different switching fields as a function of temperature. This switching diagram can be well explained by considering the competition between energy barrier of layer’s magnetization reversal, interlayer exchange coupling, and Zeeman energy.

Magnetization switching diagram of a perpendicular synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer

International Nuclear Information System (INIS)

Koplak, O.; Talantsev, A.; Lu, Y.; Hamadeh, A.; Pirro, P.; Hauet, T.; Morgunov, R.; Mangin, S.

2017-01-01

Highlights: • Anisotropy, Zeeman and exchange energy determine sequence of magnetic transitions. • Three temperature ranges manifest different shapes of the hysteresis loop. • The critical transition fields are temperature dependent. - Abstract: Magnetic configurations in synthetic ferrimagnet CoFeB/Ta/CoFeB bilayer with strong perpendicular anisotropy have been systematically studied. Magnetization versus field hysteresis loop has been measured for different temperature ranging from 5 to 300 K. The applied field – temperature (H-T) magnetization switching diagram has been constructed by extracting the different switching fields as a function of temperature. This switching diagram can be well explained by considering the competition between energy barrier of layer’s magnetization reversal, interlayer exchange coupling, and Zeeman energy.

Hexagon and stripe patterns in dielectric barrier streamer discharge

International Nuclear Information System (INIS)

Dong Lifang; He Yafeng; Yin Zengqian; Chai Zhifang

2004-01-01

We present a specially designed dielectric barrier discharge (DBD) system for the study of pattern formation. Hexagon and stripe patterns have been observed in a streamer discharge in a DBD for the first time. The phase diagram of pattern types as a function of applied voltage is given

Importance diagrams - a novel presentation of the response of a material to neutron irradiation

International Nuclear Information System (INIS)

Forrest, R.A.

1998-01-01

Activation of fusion materials following neutron irradiation is of great technological importance, especially in the study of safety and environmental impacts. Currently, activation calculations are performed for a particular neutron spectrum, appropriate to a region in a particular fusion device, which makes it difficult to extract generic information. The present work gives details of a method to present the dominant nuclides for the radiological responses or an irradiated material in a fashion that is independent of the neutron spectrum and almost independent of the flux. The importance diagrams show regions in the decay time versus neutron energy space where a nuclide contributes >50% of the response. The importance diagrams for pure iron and SS316 are described, and it is noted that the shapes of the various regions vary very little with the total neutron flux. Variation of the diagrams with irradiation time occurs at short decay times in a systematic fashion. The use of the diagrams in a realistic spectrum relies on an expansion, which while not generally true, does hold approximately for many of the nuclides of interest. The diagrams are therefore a valuable summary of the universal, device-independent, response of the materials, and when combined with pathway information give a comprehensive description of activation for that material. (orig.)

Free energy diagram for the heterogeneous enzymatic hydrolysis of glycosidic bonds in cellulose

DEFF Research Database (Denmark)

Westh, Peter; Cruys-Bagger, Nicolaj; Sørensen, Trine Holst

2015-01-01

for all stable and activated complexes defined by the reaction scheme, and hence propose a free energy diagram for the full heterogeneous process. For other Cel7A enzymes, including variants with and without carbohydrate binding module (CBM), we obtained activation parameters for the association...... no influence on the transition state for association, but increased the free energy barrier for dissociation. Hence, the CBM appeared to promote the stability of the complex by delaying dissociation rather than accelerating association....

Using social marketing to address barriers and motivators to agricultural safety and health best practices.

Science.gov (United States)

Yoder, Aaron M; Murphy, Dennis J

2012-01-01

Social marketing is an intervention development strategy that pays considerable attention to barriers to and motivators for behavioral change or adoption of recommended behaviors. Barriers are obstacles that prevent individuals from changing or adopting behaviors and are often referred to as the "cons" or "costs" of doing something. Motivators, on the other hand, are factors that encourage individuals to change or adopt behaviors and are often referred to as the "pros," "benefits," or "influencing factors" of doing something. Importantly, social marketing does not target education or knowledge change as an end point; rather, it targets behavior change. Studies across several types of desired behaviors (e.g., smoking cessation, weight control, more exercise, sunscreen use, radon testing) using the Stages of Change model have found systematic relationships between stages of change and pros and cons of changing behavior. A review of literature identifies numerous research and intervention studies that directly reference social marketing in agricultural safety and health, studies that identify reasons why parents allow their children to be exposed to hazardous situations on the farm, and reasons why youth engage in risky behaviors, but only two studies were found that show evidence of systematically researching specific behavioral change motivating factors. The authors offer several suggestions to help address issues relating to social marketing and agricultural safety and health.

Automation of Feynman diagram evaluations

International Nuclear Information System (INIS)

Tentyukov, M.N.

1998-01-01

A C-program DIANA (DIagram ANAlyser) for the automation of Feynman diagram evaluations is presented. It consists of two parts: the analyzer of diagrams and the interpreter of a special text manipulating language. This language can be used to create a source code for analytical or numerical evaluations and to keep the control of the process in general

VennDiagramWeb: a web application for the generation of highly customizable Venn and Euler diagrams.

Science.gov (United States)

Lam, Felix; Lalansingh, Christopher M; Babaran, Holly E; Wang, Zhiyuan; Prokopec, Stephenie D; Fox, Natalie S; Boutros, Paul C

2016-10-03

Visualization of data generated by high-throughput, high-dimensionality experiments is rapidly becoming a rate-limiting step in computational biology. There is an ongoing need to quickly develop high-quality visualizations that can be easily customized or incorporated into automated pipelines. This often requires an interface for manual plot modification, rapid cycles of tweaking visualization parameters, and the generation of graphics code. To facilitate this process for the generation of highly-customizable, high-resolution Venn and Euler diagrams, we introduce VennDiagramWeb: a web application for the widely used VennDiagram R package. VennDiagramWeb is hosted at http://venndiagram.res.oicr.on.ca/ . VennDiagramWeb allows real-time modification of Venn and Euler diagrams, with parameter setting through a web interface and immediate visualization of results. It allows customization of essentially all aspects of figures, but also supports integration into computational pipelines via download of R code. Users can upload data and download figures in a range of formats, and there is exhaustive support documentation. VennDiagramWeb allows the easy creation of Venn and Euler diagrams for computational biologists, and indeed many other fields. Its ability to support real-time graphics changes that are linked to downloadable code that can be integrated into automated pipelines will greatly facilitate the improved visualization of complex datasets. For application support please contact Paul.Boutros@oicr.on.ca.

Genus Ranges of Chord Diagrams.

Science.gov (United States)

Burns, Jonathan; Jonoska, Nataša; Saito, Masahico

2015-04-01

A chord diagram consists of a circle, called the backbone, with line segments, called chords, whose endpoints are attached to distinct points on the circle. The genus of a chord diagram is the genus of the orientable surface obtained by thickening the backbone to an annulus and attaching bands to the inner boundary circle at the ends of each chord. Variations of this construction are considered here, where bands are possibly attached to the outer boundary circle of the annulus. The genus range of a chord diagram is the genus values over all such variations of surfaces thus obtained from a given chord diagram. Genus ranges of chord diagrams for a fixed number of chords are studied. Integer intervals that can be, and those that cannot be, realized as genus ranges are investigated. Computer calculations are presented, and play a key role in discovering and proving the properties of genus ranges.

First Safety and Performance Evaluation of T45K, a Self-Assembling Peptide Barrier Hemostatic Device, After Skin Lesion Excision.

Science.gov (United States)

Rahmani, George; Prats, Jayne; Norchi, Terrence; Kates, Steven; McInerney, Veronica; Woods, Jack; Kelly, Jack

2018-01-29

The self-assembling peptide barrier T45K (SAPB-T45K) is an oligopeptide that rapidly forms a biocompatible hemostatic barrier when applied to wounds. Evaluate safety and performance of SAPB-T45K in cutaneous surgery. In this single-blind study, after sequential shave excision of 2 lesions, wounds were randomized (intrapatient) to SAPB-T45K or control treatment. Safety was assessed at treatment, Day 7, and Day 30. Performance was evaluated using time to hemostasis (TTH) and ASEPSIS wound scores, with a subgroup analysis for patients with or without antiplatelet therapy. Each of 46 patients (10 [22%] with antiplatelet therapy) received randomized SAPB-T45K or control treatment for 2 wounds. Safety assessments were similar, and ASEPSIS scores reflected normal healing in both wound groups. SAPB-T45K demonstrated significantly faster median TTH (24.5 [range, 7-165] seconds) compared with control (44 [10-387] seconds), for a 41% median TTH reduction (18 [95% confidence interval, 7-35] seconds, p safety profiles were similar.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

Barriers to the Adoption of Wearable Sensors in the Workplace: A Survey of Occupational Safety and Health Professionals.

Science.gov (United States)

Schall, Mark C; Sesek, Richard F; Cavuoto, Lora A

2018-05-01

To gather information on the (a) types of wearable sensors, particularly personal activity monitors, currently used by occupational safety and health (OSH) professionals; (b) potential benefits of using such technologies in the workplace; and (c) perceived barriers preventing the widespread adoption of wearable sensors in industry. Wearable sensors are increasingly being promoted as a means to improve employee health and well-being, and there is mounting evidence supporting their use as exposure assessment and personal health tools. Despite this, many workplaces have been hesitant to adopt these technologies. An electronic survey was emailed to 28,428 registered members of the American Society of Safety Engineers (ASSE) and 1,302 professionals certified by the Board of Certification in Professional Ergonomics (BCPE). A total of 952 valid responses were returned. Over half of respondents described being in favor of using wearable sensors to track OSH-related risk factors and relevant exposure metrics at their respective workplaces. However, barriers including concerns regarding employee privacy/confidentiality of collected data, employee compliance, sensor durability, the cost/benefit ratio of using wearables, and good manufacturing practice requirements were described as challenges precluding adoption. The broad adoption of wearable technologies appears to depend largely on the scientific community's ability to successfully address the identified barriers. Investigators may use the information provided to develop research studies that better address OSH practitioner concerns and help technology developers operationalize wearable sensors to improve employee health and well-being.

Assessing the adequacy and reliability of fire barriers in nuclear power plants

International Nuclear Information System (INIS)

Beard, A.N.

1991-01-01

Fire barriers on nuclear power plants are essential for proper segregation of redundant trains of safety equipment. The contribution they make to nuclear safety is obviously significant, but difficult to quantify. As a result, the analysis of fire barriers for nuclear safety justification purposes tends to concentrate on demonstrating that they are adequate instead. The paper discusses various methods of analysing fire barriers and introduces work being completed on a method for quantifying the reliability of a fire barrier. (orig.)

Collaborative diagramming during problem based learning in medical education: Do computerized diagrams support basic science knowledge construction?

Science.gov (United States)

De Leng, Bas; Gijlers, Hannie

2015-05-01

To examine how collaborative diagramming affects discussion and knowledge construction when learning complex basic science topics in medical education, including its effectiveness in the reformulation phase of problem-based learning. Opinions and perceptions of students (n = 70) and tutors (n = 4) who used collaborative diagramming in tutorial groups were collected with a questionnaire and focus group discussions. A framework derived from the analysis of discourse in computer-supported collaborative leaning was used to construct the questionnaire. Video observations were used during the focus group discussions. Both students and tutors felt that collaborative diagramming positively affected discussion and knowledge construction. Students particularly appreciated that diagrams helped them to structure knowledge, to develop an overview of topics, and stimulated them to find relationships between topics. Tutors emphasized that diagramming increased interaction and enhanced the focus and detail of the discussion. Favourable conditions were the following: working with a shared whiteboard, using a diagram format that facilitated distribution, and applying half filled-in diagrams for non-content expert tutors and\\or for heterogeneous groups with low achieving students. The empirical findings in this study support the findings of earlier more descriptive studies that diagramming in a collaborative setting is valuable for learning complex knowledge in medicine.

Integrated system of safety features for spent fuel interim storage

International Nuclear Information System (INIS)

Pantazi, Doina; Stanciu, Marcela; Mateescu, Silvia; Marin, Ion

1999-01-01

The design of the spent fuel interim storage facility (SFISF) must meet the applicable safety requirements in order to ensure radiological protection of the personnel, public and environment during all phases of the facility. To elaborate the safety documentation necessary for licensing, we were trying to chose the most appropriate approach related to safety features for SFISF, based on national and international regulations, standards and recommendations, as well as on the experience of other countries with similar facilities and finally, on our own experience in designing other nuclear objectives in Romania. The paper presents the issues that we consider important for the safety evaluation and are developed as a detailed diagram. The diagram contains in a logical succession the following issues: - fundamental principles of radioprotection; - fundamental safety principles of radioactive waste management; - safety objectives of SFISF; - safety criteria for SFISF; - safety requirements for SFISF; - siting criteria for SFISF; - siting requirements for SFISF. (authors)

Asymptotic laws for random knot diagrams

Science.gov (United States)

Chapman, Harrison

2017-06-01

We study random knotting by considering knot and link diagrams as decorated, (rooted) topological maps on spheres and pulling them uniformly from among sets of a given number of vertices n, as first established in recent work with Cantarella and Mastin. The knot diagram model is an exciting new model which captures both the random geometry of space curve models of knotting as well as the ease of computing invariants from diagrams. We prove that unknot diagrams are asymptotically exponentially rare, an analogue of Sumners and Whittington’s landmark result for self-avoiding polygons. Our proof uses the same key idea: we first show that knot diagrams obey a pattern theorem, which describes their fractal structure. We examine how quickly this behavior occurs in practice. As a consequence, almost all diagrams are asymmetric, simplifying sampling from this model. We conclude with experimental data on knotting in this model. This model of random knotting is similar to those studied by Diao et al, and Dunfield et al.

Safety Concepts in Structural Glass Engineering : Towards an Integrated Approach

NARCIS (Netherlands)

Bos, F.P.

2009-01-01

This dissertation proposes the Integrated Approach to Structural Glass Safety, based on four clearly defined element safety properties, damage sensitivity, relative resistance, redundancy, and fracture mode. The Element Safety Diagram (ESD) is introduced to provide an easy-to-read graphical

Drawing Euler Diagrams with Circles

OpenAIRE

Stapleton, Gem; Zhang, Leishi; Howse, John; Rodgers, Peter

2010-01-01

Euler diagrams are a popular and intuitive visualization tool which are used in a wide variety of application areas, including biological and medical data analysis. As with other data visualization methods, such as graphs, bar charts, or pie charts, the automated generation of an Euler diagram from a suitable data set would be advantageous, removing the burden of manual data analysis and the subsequent task of drawing an appropriate diagram. Various methods have emerged that automatically dra...

49 CFR 587.18 - Dimensions of fixed rigid barrier.

Science.gov (United States)

2010-10-01

... TRAFFIC SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) DEFORMABLE BARRIERS Offset Deformable Barrier § 587.18 Dimensions of fixed rigid barrier. (a) The fixed rigid barrier has a mass of not... 49 Transportation 7 2010-10-01 2010-10-01 false Dimensions of fixed rigid barrier. 587.18 Section...

Roadside design in The Netherlands for enhancing safety : contribution to the conference `Traffic safety on Two Continents', Lisbon, Portugal, September 22-24, 1997.

NARCIS (Netherlands)

Schoon, C.C.

1998-01-01

Safety barriers are often used on motorways. Accident figures, however, show that a safety barrier is involved in approximately 20% of all fatal accidents. This paper considers safety barriers within the context of safe designs for shoulders on motorways. This research is related to the European

Rigorous analysis of image force barrier lowering in bounded geometries: application to semiconducting nanowires

International Nuclear Information System (INIS)

Calahorra, Yonatan; Mendels, Dan; Epstein, Ariel

2014-01-01

Bounded geometries introduce a fundamental problem in calculating the image force barrier lowering of metal-wrapped semiconductor systems. In bounded geometries, the derivation of the barrier lowering requires calculating the reference energy of the system, when the charge is at the geometry center. In the following, we formulate and rigorously solve this problem; this allows combining the image force electrostatic potential with the band diagram of the bounded geometry. The suggested approach is applied to spheres as well as cylinders. Furthermore, although the expressions governing cylindrical systems are complex and can only be evaluated numerically, we present analytical approximations for the solution, which allow easy implementation in calculated band diagrams. The results are further used to calculate the image force barrier lowering of metal-wrapped cylindrical nanowires; calculations show that although the image force potential is stronger than that of planar systems, taking the complete band-structure into account results in a weaker effect of barrier lowering. Moreover, when considering small diameter nanowires, we find that the electrostatic effects of the image force exceed the barrier region, and influence the electronic properties of the nanowire core. This study is of interest to the nanowire community, and in particular for the analysis of nanowire I−V measurements where wrapped or omega-shaped metallic contacts are used. (paper)

A comparison of freeway median crash frequency, severity, and barrier strike outcomes by median barrier type.

Science.gov (United States)

Russo, Brendan J; Savolainen, Peter T

2018-08-01

Median-crossover crashes are among the most hazardous events that can occur on freeways, often resulting in severe or fatal injuries. The primary countermeasure to reduce the occurrence of such crashes is the installation of a median barrier. When installation of a median barrier is warranted, transportation agencies are faced with the decision among various alternatives including concrete barriers, beam guardrail, or high-tension cable barriers. Each barrier type differs in terms of its deflection characteristics upon impact, the required installation and maintenance costs, and the roadway characteristics (e.g., median width) where installation would be feasible. This study involved an investigation of barrier performance through an in-depth analysis of crash frequency and severity data from freeway segments where high-tension cable, thrie-beam, and concrete median barriers were installed. A comprehensive manual review of crash reports was conducted to identify crashes in which a vehicle left the roadway and encroached into the median. This review also involved an examination of crash outcomes when a barrier strike occurred, which included vehicle containment, penetration, or re-direction onto the travel lanes. The manual review of crash reports provided critical supplementary information through narratives and diagrams not normally available through standard fields on police crash report forms. Statistical models were estimated to identify factors that affect the frequency, severity, and outcomes of median-related crashes, with particular emphases on differences between segments with varying median barrier types. Several roadway-, traffic-, and environmental-related characteristics were found to affect these metrics, with results varying across the different barrier types. The results of this study provide transportation agencies with important guidance as to the in-service performance of various types of median barrier. Copyright © 2018 Elsevier Ltd. All rights

Applications of nanotechnology in food packaging and food safety: barrier materials, antimicrobials and sensors.

Science.gov (United States)

Duncan, Timothy V

2011-11-01

In this article, several applications of nanomaterials in food packaging and food safety are reviewed, including: polymer/clay nanocomposites as high barrier packaging materials, silver nanoparticles as potent antimicrobial agents, and nanosensors and nanomaterial-based assays for the detection of food-relevant analytes (gasses, small organic molecules and food-borne pathogens). In addition to covering the technical aspects of these topics, the current commercial status and understanding of health implications of these technologies are also discussed. These applications were chosen because they do not involve direct addition of nanoparticles to consumed foods, and thus are more likely to be marketed to the public in the short term. Published by Elsevier Inc.

Current collectors for improved safety

Science.gov (United States)

Abdelmalak, Michael Naguib; Allu, Srikanth; Dudney, Nancy J.; Li, Jianlin; Simunovic, Srdjan; Wang, Hsin

2017-12-19

A battery electrode assembly includes a current collector with conduction barrier regions having a conductive state in which electrical conductivity through the conduction barrier region is permitted, and a safety state in which electrical conductivity through the conduction barrier regions is reduced. The conduction barrier regions change from the conductive state to the safety state when the current collector receives a short-threatening event. An electrode material can be connected to the current collector. The conduction barrier regions can define electrical isolation subregions. A battery is also disclosed, and methods for making the electrode assembly, methods for making a battery, and methods for operating a battery.

Radioactive wastes. Safety of storage facilities

International Nuclear Information System (INIS)

Devillers, Ch.

2001-01-01

A radioactive waste storage facility is designed in a way that ensures the isolation of wastes with respect to the biosphere. This function comprises the damping of the gamma and neutron radiations from the wastes, and the confinement of the radionuclides content of the wastes. The safety approach is based on two time scales: the safety of the insulation system during the main phase of radioactive decay, and the assessment of the radiological risks following this phase. The safety of a surface storage facility is based on a three-barrier concept (container, storage structures, site). The confidence in the safety of the facility is based on the quality assurance of the barriers and on their surveillance and maintenance. The safety of a deep repository will be based on the site quality, on the design and construction of structures and on the quality of the safety demonstration. This article deals with the safety approach and principles of storage facilities: 1 - recall of the different types of storage facilities; 2 - different phases of the life of a storage facility and regulatory steps; 3 - safety and radiation protection goals (time scales, radiation protection goals); 4 - safety approach and principles of storage facilities: safety of the isolation system (confinement system, safety analysis, scenarios, radiological consequences, safety principles), assessment of the radiation risks after the main phase of decay; 5 - safety of surface storage facilities: safety analysis of the confinement system of the Aube plant (barriers, scenarios, modeling, efficiency), evaluation of radiological risks after the main phase of decay; experience feedback of the Manche plant; variants of surface storage facilities in France and abroad (very low activity wastes, mine wastes, short living wastes with low and average activity); 6 - safety of deep geological disposal facilities: legal framework of the French research; international context; safety analysis of the confinement system

Converse Barrier Certificate Theorem

DEFF Research Database (Denmark)

Wisniewski, Rafael; Sloth, Christoffer

2013-01-01

This paper presents a converse barrier certificate theorem for a generic dynamical system.We show that a barrier certificate exists for any safe dynamical system defined on a compact manifold. Other authors have developed a related result, by assuming that the dynamical system has no singular...... points in the considered subset of the state space. In this paper, we redefine the standard notion of safety to comply with generic dynamical systems with multiple singularities. Afterwards, we prove the converse barrier certificate theorem and illustrate the differences between ours and previous work...

Drug safety is a barrier to the discovery and development of new androgen receptor antagonists.

Science.gov (United States)

Foster, William R; Car, Bruce D; Shi, Hong; Levesque, Paul C; Obermeier, Mary T; Gan, Jinping; Arezzo, Joseph C; Powlin, Stephanie S; Dinchuk, Joseph E; Balog, Aaron; Salvati, Mark E; Attar, Ricardo M; Gottardis, Marco M

2011-04-01

Androgen receptor (AR) antagonists are part of the standard of care for prostate cancer. Despite the almost inevitable development of resistance in prostate tumors to AR antagonists, no new AR antagonists have been approved for over a decade. Treatment failure is due in part to mutations that increase activity of AR in response to lower ligand concentrations as well as to mutations that result in AR response to a broader range of ligands. The failure to discover new AR antagonists has occurred in the face of continued research; to enable progress, a clear understanding of the reasons for failure is required. Non-clinical drug safety studies and safety pharmacology assays were performed on previously approved AR antagonists (bicalutamide, flutamide, nilutamide), next generation antagonists in clinical testing (MDV3100, BMS-641988), and a pre-clinical drug candidate (BMS-501949). In addition, non-clinical studies with AR mutant mice, and EEG recordings in rats were performed. Non-clinical findings are compared to disclosures of clinical trial results. As a drug class, AR antagonists cause seizure in animals by an off-target mechanism and are found in vitro to inhibit GABA-A currents. Clinical trials of candidate next generation AR antagonists identify seizure as a clinical safety risk. Non-clinical drug safety profiles of the AR antagonist drug class create a significant barrier to the identification of next generation AR antagonists. GABA-A inhibition is a common off-target activity of approved and next generation AR antagonists potentially explaining some side effects and safety hazards of this class of drugs. Copyright © 2010 Wiley-Liss, Inc.

On-shell diagrams for N=8 supergravity amplitudes

Energy Technology Data Exchange (ETDEWEB)

Heslop, Paul; Lipstein, Arthur E. [Department of Mathematical Sciences, Durham University,Lower Mountjoy, Stockton Road, Durham, DH1 3LE (United Kingdom)

2016-06-10

We define recursion relations for N=8 supergravity amplitudes using a generalization of the on-shell diagrams developed for planar N=4 super-Yang-Mills. Although the recursion relations generically give rise to non-planar on-shell diagrams, we show that at tree-level the recursion can be chosen to yield only planar diagrams, the same diagrams occurring in the planar N=4 theory. This implies non-trivial identities for non-planar diagrams as well as interesting relations between the N=4 and N=8 theories. We show that the on-shell diagrams of N=8 supergravity obey equivalence relations analogous to those of N=4 super-Yang-Mills, and we develop a systematic algorithm for reading off Grassmannian integral formulae directly from the on-shell diagrams. We also show that the 1-loop 4-point amplitude of N=8 supergravity can be obtained from on-shell diagrams.

Phase diagram of ammonium nitrate

Energy Technology Data Exchange (ETDEWEB)

Dunuwille, Mihindra; Yoo, Choong-Shik, E-mail: csyoo@wsu.edu [Department of Chemistry and Institute for Shock Physics, Washington State University, Pullman, Washington 99164 (United States)

2013-12-07

Ammonium Nitrate (AN) is a fertilizer, yet becomes an explosive upon a small addition of chemical impurities. The origin of enhanced chemical sensitivity in impure AN (or AN mixtures) is not well understood, posing significant safety issues in using AN even today. To remedy the situation, we have carried out an extensive study to investigate the phase stability of AN and its mixtures with hexane (ANFO–AN mixed with fuel oil) and Aluminum (Ammonal) at high pressures and temperatures, using diamond anvil cells (DAC) and micro-Raman spectroscopy. The results indicate that pure AN decomposes to N{sub 2}, N{sub 2}O, and H{sub 2}O at the onset of the melt, whereas the mixtures, ANFO and Ammonal, decompose at substantially lower temperatures. The present results also confirm the recently proposed phase IV-IV{sup ′} transition above 17 GPa and provide new constraints for the melting and phase diagram of AN to 40 GPa and 400°C.

Phase diagram of ammonium nitrate

International Nuclear Information System (INIS)

Dunuwille, Mihindra; Yoo, Choong-Shik

2013-01-01

Ammonium Nitrate (AN) is a fertilizer, yet becomes an explosive upon a small addition of chemical impurities. The origin of enhanced chemical sensitivity in impure AN (or AN mixtures) is not well understood, posing significant safety issues in using AN even today. To remedy the situation, we have carried out an extensive study to investigate the phase stability of AN and its mixtures with hexane (ANFO–AN mixed with fuel oil) and Aluminum (Ammonal) at high pressures and temperatures, using diamond anvil cells (DAC) and micro-Raman spectroscopy. The results indicate that pure AN decomposes to N 2 , N 2 O, and H 2 O at the onset of the melt, whereas the mixtures, ANFO and Ammonal, decompose at substantially lower temperatures. The present results also confirm the recently proposed phase IV-IV ′ transition above 17 GPa and provide new constraints for the melting and phase diagram of AN to 40 GPa and 400°C

Barriers to the future

Energy Technology Data Exchange (ETDEWEB)

Massey, C T

1986-09-01

Opportunities for the British coal industry seem vast yet there are still barriers to progress. Seven areas are identified and discussed: mining mobility (for example, longwall mining systems are rigid and inflexible compared with American stall and pillar working); mine structure (many mines are more suitable to pit ponies than to large pieces of equipment); financial barriers (Government requires the industry to break even in 1987/88); personnel barriers (less specialization, better use of skills); safety barriers (increased use of remote control, ergonomics and robotics to protect workers); microelectronic management (nationalization has cushioned management from the market place; there is a need for a more multidisciplinary approach to the industry); and legal barriers (most legislation in the past has been in response to accidents; legislation external to the industry but affecting it is more fundamental).

The mean squared writhe of alternating random knot diagrams

Energy Technology Data Exchange (ETDEWEB)

Diao, Y; Hinson, K [Department of Mathematics and Statistics University of North Carolina at Charlotte, NC 28223 (United States); Ernst, C; Ziegler, U, E-mail: ydiao@uncc.ed [Department of Mathematics and Computer Science, Western Kentucky University, Bowling Green, KY 42101 (United States)

2010-12-10

The writhe of a knot diagram is a simple geometric measure of the complexity of the knot diagram. It plays an important role not only in knot theory itself, but also in various applications of knot theory to fields such as molecular biology and polymer physics. The mean squared writhe of any sample of knot diagrams with n crossings is n when for each diagram at each crossing one of the two strands is chosen as the overpass at random with probability one-half. However, such a diagram is usually not minimal. If we restrict ourselves to a minimal knot diagram, then the choice of which strand is the over- or under-strand at each crossing is no longer independent of the neighboring crossings and a larger mean squared writhe is expected for minimal diagrams. This paper explores the effect on the correlation between the mean squared writhe and the diagrams imposed by the condition that diagrams are minimal by studying the writhe of classes of reduced, alternating knot diagrams. We demonstrate that the behavior of the mean squared writhe heavily depends on the underlying space of diagram templates. In particular this is true when the sample space contains only diagrams of a special structure. When the sample space is large enough to contain not only diagrams of a special type, then the mean squared writhe for n crossing diagrams tends to grow linearly with n, but at a faster rate than n, indicating an intrinsic property of alternating knot diagrams. Studying the mean squared writhe of alternating random knot diagrams also provides some insight into the properties of the diagram generating methods used, which is an important area of study in the applications of random knot theory.

Using Affinity Diagrams to Evaluate Interactive Prototypes

DEFF Research Database (Denmark)

Lucero, Andrés

2015-01-01

our particular use of affinity diagramming in prototype evaluations. We reflect on a decade’s experience using affinity diagramming across a number of projects, both in industry and academia. Our affinity diagramming process in interaction design has been tailored and consists of four stages: creating...

The amplituhedron from momentum twistor diagrams

International Nuclear Information System (INIS)

Bai, Yuntao; He, Song

2015-01-01

We propose a new diagrammatic formulation of the all-loop scattering amplitudes/Wilson loops in planar N=4 SYM, dubbed the “momentum-twistor diagrams”. These are on-shell-diagrams obtained by gluing trivalent black and white vertices in momentum twistor space, which, in the reduced diagram case, are known to be related to diagrams in the original twistor space. The new diagrams are manifestly Yangian invariant, and they naturally represent factorization and forward-limit contributions in the all-loop BCFW recursion relations in momentum twistor space, in a fashion that is completely different from those in momentum space. We show how to construct and evaluate momentum-twistor diagrams, and how to use them to obtain tree-level amplitudes and loop-level integrands; in particular the latter involve isolated bubble-structures for loop variables arising from forward limits, or the entangled removal of particles. From each diagram, the generalized “boundary measurement” directly gives the C, D matrices, thus a cell in the amplituhedron associated with the amplitude, and we expect that our diagrammatic representations of the amplitude provide triangulations of the amplituhedron. To demonstrate the computational power of the formalism, we give explicit results for general two-loop integrands, and the cells of the amplituhedron for two-loop MHV amplitudes.

Diagram Techniques in Group Theory

Science.gov (United States)

Stedman, Geoffrey E.

2009-09-01

Preface; 1. Elementary examples; 2. Angular momentum coupling diagram techniques; 3. Extension to compact simple phase groups; 4. Symmetric and unitary groups; 5. Lie groups and Lie algebras; 6. Polarisation dependence of multiphoton processes; 7. Quantum field theoretic diagram techniques for atomic systems; 8. Applications; Appendix; References; Indexes.

ENA study cites barriers to NPSG compliance.

Science.gov (United States)

2009-04-01

There are many barriers to compliance with the National Patient Safety Goals, as a recent study shows. However, emergency medicine experts say there are several strategies you can adopt to help overcome those barriers. Send the right message to your staff by establishing a culture of shared responsibility for safety. Establish scripts for talking with patients. Standardization will help ensure they are getting the correct information. Put standardized abbreviations on posters in your department, and list them on your medication reconciliation form.

Enhancement of Hole Confinement by Monolayer Insertion in Asymmetric Quantum-Barrier UVB Light Emitting Diodes

KAUST Repository

Janjua, Bilal; Alyamani, Ahmed Y.; El-Desouki, M. M.; Ng, Tien Khee; Ooi, Boon S.

2014-01-01

We study the enhanced hole confinement by having a large bandgap AlGaN monolayer insertion (MLI) between the quantum well (QW) and the quantum barrier (QB). The numerical analysis examines the energy band alignment diagrams, using a self

Break down these barriers to medication safety.

Science.gov (United States)

2009-06-01

Survey says of 2,200 ED nurses from 131 EDs, barriers to complying with medication-related NPSGs are common. Consider additional education of employees. One hospital uses computerized charting system to quicken triage process.

Memory-induced acceleration and slowdown of barrier crossing

Science.gov (United States)

Kappler, Julian; Daldrop, Jan O.; Brünig, Florian N.; Boehle, Moritz D.; Netz, Roland R.

2018-01-01

We study the mean first-passage time τMFP for the barrier crossing of a single massive particle with non-Markovian memory by Langevin simulations in one dimension. In the Markovian limit of short memory time τΓ, the expected Kramers turnover between the overdamped (high-friction) and the inertial (low-friction) limits is recovered. Compared to the Markovian case, we find barrier crossing to be accelerated for intermediate memory time, while for long memory time, barrier crossing is slowed down and τMFP increases with τΓ as a power law τM F P˜τΓ2. Both effects are derived from an asymptotic propagator analysis: while barrier crossing acceleration at intermediate memory can be understood as an effective particle mass reduction, slowing down for long memory is caused by the slow kinetics of energy diffusion. A simple and globally accurate heuristic formula for τMFP in terms of all relevant time scales of the system is presented and used to establish a scaling diagram featuring the Markovian overdamped and the Markovian inertial regimes, as well as the non-Markovian intermediate memory time regime where barrier crossing is accelerated and the non-Markovian long memory time regime where barrier crossing is slowed down.

The role of barriers in the final storage of alpha-contaminated waste

International Nuclear Information System (INIS)

Sousselier, Y.

1981-01-01

The long-term safety of the final storage of waste, for which durations of the order of 10 4 -10 5 years may reasonably be foreseen, is based on the use of various barriers. The first barrier, which is essential in intermediate storage, should have the lowest possible leaching rate in order to play its part in final storage. The role of the second barrier is to provide protection to the first or to serve as a constituent of the overall protection system. The third barrier is expected to be the artificial barrier with the longest lifetime, and should be combined with the fourth so as to add to its effectiveness. The safety analysis should thus study the overall behaviour of the barriers as a whole, which should ensure a very high degree of safety, and also take into account the hazard of intrusion, intentional or otherwise, by future generations. (author)

Logic verification system for power plant sequence diagrams

International Nuclear Information System (INIS)

Fukuda, Mitsuko; Yamada, Naoyuki; Teshima, Toshiaki; Kan, Ken-ichi; Utsunomiya, Mitsugu.

1994-01-01

A logic verification system for sequence diagrams of power plants has been developed. The system's main function is to verify correctness of the logic realized by sequence diagrams for power plant control systems. The verification is based on a symbolic comparison of the logic of the sequence diagrams with the logic of the corresponding IBDs (interlock Block Diagrams) in combination with reference to design knowledge. The developed system points out the sub-circuit which is responsible for any existing mismatches between the IBD logic and the logic realized by the sequence diagrams. Applications to the verification of actual sequence diagrams of power plants confirmed that the developed system is practical and effective. (author)

Comprehending 3D Diagrams: Sketching to Support Spatial Reasoning.

Science.gov (United States)

Gagnier, Kristin M; Atit, Kinnari; Ormand, Carol J; Shipley, Thomas F

2017-10-01

Science, technology, engineering, and mathematics (STEM) disciplines commonly illustrate 3D relationships in diagrams, yet these are often challenging for students. Failing to understand diagrams can hinder success in STEM because scientific practice requires understanding and creating diagrammatic representations. We explore a new approach to improving student understanding of diagrams that convey 3D relations that is based on students generating their own predictive diagrams. Participants' comprehension of 3D spatial diagrams was measured in a pre- and post-design where students selected the correct 2D slice through 3D geologic block diagrams. Generating sketches that predicated the internal structure of a model led to greater improvement in diagram understanding than visualizing the interior of the model without sketching, or sketching the model without attempting to predict unseen spatial relations. In addition, we found a positive correlation between sketched diagram accuracy and improvement on the diagram comprehension measure. Results suggest that generating a predictive diagram facilitates students' abilities to make inferences about spatial relationships in diagrams. Implications for use of sketching in supporting STEM learning are discussed. Copyright © 2016 Cognitive Science Society, Inc.

Reliability model for helicopter main gearbox lubrication system using influence diagrams

International Nuclear Information System (INIS)

Rashid, H.S.J.; Place, C.S.; Mba, D.; Keong, R.L.C.; Healey, A.; Kleine-Beek, W.; Romano, M.

2015-01-01

The loss of oil from a helicopter main gearbox (MGB) leads to increased friction between components, a rise in component surface temperatures, and subsequent mechanical failure of gearbox components. A number of significant helicopter accidents have been caused due to such loss of lubrication. This paper presents a model to assess the reliability of helicopter MGB lubricating systems. Safety risk modeling was conducted for MGB oil system related accidents in order to analyse key failure mechanisms and the contributory factors. Thus, the dominant failure modes for lubrication systems and key contributing components were identified. The Influence Diagram (ID) approach was then employed to investigate reliability issues of the MGB lubrication systems at the level of primary causal factors, thus systematically investigating a complex context of events, conditions, and influences that are direct triggers of the helicopter MGB lubrication system failures. The interrelationships between MGB lubrication system failure types were thus identified, and the influence of each of these factors on the overall MGB lubrication system reliability was assessed. This paper highlights parts of the HELMGOP project, sponsored by the European Aviation Safety Agency to improve helicopter main gearbox reliability. - Highlights: • We investigated methods to optimize helicopter MGB oil system run-dry capability. • Used Influence Diagram to assess design and maintenance factors of MGB oil system. • Factors influencing overall MGB lubrication system reliability were identified. • This globally influences current and future helicopter MGB designs

Return-to-work barriers for workers with contact dermatitis.

Science.gov (United States)

Holness, D Linn

2003-12-01

There is little information available regarding barriers to return-to-work (RTW) in workers with contact dermatitis. The purpose of this study was to survey occupational health and safety personnel to determine their perceptions regarding RTW barriers for workers with contact dermatitis. The study was conducted during an occupational health and safety research conference attended by stakeholders from labour, management, injured workers, government, safety associations, occupational health and safety practitioners and researchers. The attendees were presented with 3 pictures of varying degrees of work-related hand contact dermatitis and were asked to list the 3 key barriers or challenges in RTW for individuals with contact dermatitis. 21 individuals completed the survey. Issues identified in descending order of frequency were concern of ongoing dermatitis, ability to do the job safely, appearance, ability to accommodate, personal protective equipment, fear that the rash was contagious, workplace attitudes and pain. While some of these issues are potentially common to RTW situations in general, others are more specific to health problems which have a visible manifestation. Increased awareness of and attention to these possible barriers to RTW may lead to better RTW outcomes.

Satake diagrams of affine Kac-Moody algebras

Energy Technology Data Exchange (ETDEWEB)

Tripathy, L K [S B R Government Womens' College, Berhampur, Orissa 760 001 (India); Pati, K C [Department of Physics, Khallikote College, Berhampur, Orissa 760 001 (India)

2006-02-10

Satake diagrams of affine Kac-Moody algebras (untwisted and twisted) are obtained from their Dynkin diagrams. These diagrams give a classification of restricted root systems associated with these algebras. In the case of simple Lie algebras, these root systems and Satake diagrams correspond to symmetric spaces which have recently found many physical applications in quantum integrable systems, quantum transport problems, random matrix theories etc. We hope these types of root systems may have similar applications in theoretical physics in future and may correspond to symmetric spaces analogue of affine Kac-Moody algebras if they exist.

The role of PSA in safety management

International Nuclear Information System (INIS)

Szikszai, T.

1997-01-01

The presentation discusses the following issues: defence in depth principle (the role of the barriers, how does PSA represents the barriers?); the safety management and nuclear power plants; the probabilistic and deterministic approaches; the PSA applications and safety management

Safety barriers and lighting columns.

NARCIS (Netherlands)

Schreuder, D.A.

1972-01-01

Problems arising from the sitting of lighting columns on the central reserve are reviewed, and remedial measures such as break-away lighting supports and installation of safety fences on the central reserve on both sides of the lighting columns are examined.

Contingency diagrams as teaching tools

OpenAIRE

Mattaini, Mark A.

1995-01-01

Contingency diagrams are particularly effective teaching tools, because they provide a means for students to view the complexities of contingency networks present in natural and laboratory settings while displaying the elementary processes that constitute those networks. This paper sketches recent developments in this visualization technology and illustrates approaches for using contingency diagrams in teaching.

Delimiting diagrams

NARCIS (Netherlands)

Oostrom, V. van

2004-01-01

We introduce the unifying notion of delimiting diagram. Hitherto unrelated results such as: Minimality of the internal needed strategy for orthogonal first-order term rewriting systems, maximality of the limit strategy for orthogonal higher-order pattern rewrite systems (with maximality of the

ROLE OF UML SEQUENCE DIAGRAM CONSTRUCTS IN OBJECT LIFECYCLE CONCEPT

Directory of Open Access Journals (Sweden)

Miroslav Grgec

2007-06-01

Full Text Available When modeling systems and using UML concepts, a real system can be viewed in several ways. The RUP (Rational Unified Process defines the "4 + 1 view": 1. Logical view (class diagram (CD, object diagram (OD, sequence diagram (SD, collaboration diagram (COD, state chart diagram (SCD, activity diagram (AD, 2.Process view (use case diagram, CD, OD, SD, COD, SCD, AD, 3. Development view (package diagram, component diagram, 4. Physical view (deployment diagram, and 5. Use case view (use case diagram, OD, SD, COD, SCD, AD which combines the four mentioned above. With sequence diagram constructs we are describing object behavior in scope of one use case and their interaction. Each object in system goes through a so called lifecycle (create, supplement object with data, use object, decommission object. The concept of the object lifecycle is used to understand and formalize the behavior of objects from creation to deletion. With help of sequence diagram concepts our paper will describe the way of interaction modeling between objects through lifeline of each of them, and their importance in software development.

A novel decision diagrams extension method

International Nuclear Information System (INIS)

Li, Shumin; Si, Shubin; Dui, Hongyan; Cai, Zhiqiang; Sun, Shudong

2014-01-01

Binary decision diagram (BDD) is a graph-based representation of Boolean functions. It is a directed acyclic graph (DAG) based on Shannon's decomposition. Multi-state multi-valued decision diagram (MMDD) is a natural extension of BDD for the symbolic representation and manipulation of the multi-valued logic functions. This paper proposes a decision diagram extension method based on original BDD/MMDD while the scale of a reliability system is extended. Following a discussion of decomposition and physical meaning of BDD and MMDD, the modeling method of BDD/MMDD based on original BDD/MMDD is introduced. Three case studies are implemented to demonstrate the presented methods. Compared with traditional BDD and MMDD generation methods, the decision diagrams extension method is more computationally efficient as shown through the running time

Initiation and arrest - two approaches to pressure vessel safety

International Nuclear Information System (INIS)

Brumovsky, M.; Filip, R.; Stepanek, S.

1976-01-01

The safety analysis is described of the reactor pressure vessel related to brittle fracture based on the fracture mechanics theory using two different approximations, i.e., the Crack Arrest Temperature (CAT) or Nil Ductility Temperature (NDT), and fracture toughness. The variation of CAT with stress was determined for different steel specimens of 120 to 200 mm in thickness. A diagram is shown of CAT variation with stress allowing the determination of crack arrest temperature for all types of commonly used steels independently of the NDT initial value. The diagram also shows that the difference between fracture transition elastic (FTE) and NDT depends on the type of material and determines the value of the ΔTsub(sigma) factor typical of the safety coefficient. The so-called fracture toughness reference value Ksub(IR) is recommended for the computation of pressure vessel criticality. Also shown is a defect analysis diagram which may be used for the calculation of pressure vessel safety prior to and during operation and which may also be used in making the decision on what crack sizes are critical, what cracks may be arrested and what cracks are likely to expand. The diagram is also important for the fact that it is material-independent and may be employed for the estimates of pre-operational and operational inspections and for pressure vessel life prediction. It is generally applicable to materials of greater thickness in the region where the validity of linear elastic fracture mechanics is guaranteed. (J.P.)

Scheil-Gulliver Constituent Diagrams

Science.gov (United States)

Pelton, Arthur D.; Eriksson, Gunnar; Bale, Christopher W.

2017-06-01

During solidification of alloys, conditions often approach those of Scheil-Gulliver cooling in which it is assumed that solid phases, once precipitated, remain unchanged. That is, they no longer react with the liquid or with each other. In the case of equilibrium solidification, equilibrium phase diagrams provide a valuable means of visualizing the effects of composition changes upon the final microstructure. In the present study, we propose for the first time the concept of Scheil-Gulliver constituent diagrams which play the same role as that in the case of Scheil-Gulliver cooling. It is shown how these diagrams can be calculated and plotted by the currently available thermodynamic database computing systems that combine Gibbs energy minimization software with large databases of optimized thermodynamic properties of solutions and compounds. Examples calculated using the FactSage system are presented for the Al-Li and Al-Mg-Zn systems, and for the Au-Bi-Sb-Pb system and its binary and ternary subsystems.

ANALYSIS OF FLEXIBLE BARRIERS USED AS SAFETY PROTECTION IN WOODWORKING

Directory of Open Access Journals (Sweden)

Ana Pavlovic

2016-03-01

Full Text Available Machine tools use physical barriers, made by flexible thermoplastic materials, to protect the environment and the operators against the projections of wood chips and parts of cutting tools. These barriers constitute a partial closure and allow the passage of the workpiece, being simultaneously able to contain sharp fragments projected at high speed. The present research was conducted with the aim to evaluate the real effectiveness of these barriers, to investigate their dynamic behaviour by numerical simulations. Results showed that these barriers, if properly considered, could retain heavier masses and higher speeds. The research also allowed, in fact, to investigate the influence of several factors in design, selection and use, as material, shape, position, assemblages and many others, highlighting weaknesses and identifying possible measures to increase its effectiveness.

Nuclear safety chains

International Nuclear Information System (INIS)

Robbins, M.C.; Eames, G.F.; Mayell, J.R.

1981-01-01

An original scheme has been developed for expressing the complex interrelationships associated with the engineered safeguards provided for a nuclear power station. This management tool, based upon network diagrams called Nuclear Safety Chains, looks at the function required of a particular item of safety plant, defines all of the vital supplies and support features necessary for successful operation, and expresses them in visual form, to facilitate analysis and optimisation for operations and maintenance staff. The safety chains are confined to manual schemes at present, although they are designed to be compatible with modern computer techniques. Their usefulness with any routine maintenance planning application on high technology plant is already being appreciated. (author)

Operations space diagram for ECRH and ECCD

DEFF Research Database (Denmark)

Bindslev, H.

2004-01-01

at the design phase. At the operations phase it may also prove useful in setting up experimental scenarios by showing operational possibilities, avoiding the need for survey type ray-tracing at the initial planning stages. The diagram may also serve the purpose of communicating operational possibilities to non......A Clemmov-Mullaly-Allis (CMA) type diagram, the ECW-CMA diagram, for representing the operational possibilities of electron cyclotron heating and current drive (ECRH/ECCD) systems for fusion plasmas is presented. In this diagram, with normalized density and normalized magnetic field coordinates......, the parameter range in which it is possible to achieve a given task (e.g. O-mode current drive for stabilizing a neoclassical tearing mode) appears as a region. With also the Greenwald density limit shown, this diagram condenses the information on operational possibilities, facilitating the overview required...

Penguin-like diagrams from the standard model

International Nuclear Information System (INIS)

Ping, Chia Swee

2015-01-01

The Standard Model is highly successful in describing the interactions of leptons and quarks. There are, however, rare processes that involve higher order effects in electroweak interactions. One specific class of processes is the penguin-like diagram. Such class of diagrams involves the neutral change of quark flavours accompanied by the emission of a gluon (gluon penguin), a photon (photon penguin), a gluon and a photon (gluon-photon penguin), a Z-boson (Z penguin), or a Higgs-boson (Higgs penguin). Such diagrams do not arise at the tree level in the Standard Model. They are, however, induced by one-loop effects. In this paper, we present an exact calculation of the penguin diagram vertices in the ‘tHooft-Feynman gauge. Renormalization of the vertex is effected by a prescription by Chia and Chong which gives an expression for the counter term identical to that obtained by employing Ward-Takahashi identity. The on-shell vertex functions for the penguin diagram vertices are obtained. The various penguin diagram vertex functions are related to one another via Ward-Takahashi identity. From these, a set of relations is obtained connecting the vertex form factors of various penguin diagrams. Explicit expressions for the gluon-photon penguin vertex form factors are obtained, and their contributions to the flavor changing processes estimated

Penguin-like diagrams from the standard model

Energy Technology Data Exchange (ETDEWEB)

Ping, Chia Swee [High Impact Research, University of Malaya, 50603 Kuala Lumpur (Malaysia)

2015-04-24

The Standard Model is highly successful in describing the interactions of leptons and quarks. There are, however, rare processes that involve higher order effects in electroweak interactions. One specific class of processes is the penguin-like diagram. Such class of diagrams involves the neutral change of quark flavours accompanied by the emission of a gluon (gluon penguin), a photon (photon penguin), a gluon and a photon (gluon-photon penguin), a Z-boson (Z penguin), or a Higgs-boson (Higgs penguin). Such diagrams do not arise at the tree level in the Standard Model. They are, however, induced by one-loop effects. In this paper, we present an exact calculation of the penguin diagram vertices in the ‘tHooft-Feynman gauge. Renormalization of the vertex is effected by a prescription by Chia and Chong which gives an expression for the counter term identical to that obtained by employing Ward-Takahashi identity. The on-shell vertex functions for the penguin diagram vertices are obtained. The various penguin diagram vertex functions are related to one another via Ward-Takahashi identity. From these, a set of relations is obtained connecting the vertex form factors of various penguin diagrams. Explicit expressions for the gluon-photon penguin vertex form factors are obtained, and their contributions to the flavor changing processes estimated.

Common phase diagram for low-dimensional superconductors

International Nuclear Information System (INIS)

Michalak, Rudi

2003-01-01

A phenomenological phase diagram which has been derived for high-temperature superconductors from NMR Knight-shift measurements of the pseudogap is compared to the phase diagram that is obtained for organic superconductors and spin-ladder superconductors, both low-dimensional systems. This is contrasted to the phase diagram of some Heavy Fermion superconductors, i.e. superconductors not constrained to a low dimensionality

Feynman diagrams without Feynman parameters

International Nuclear Information System (INIS)

Mendels, E.

1978-01-01

Dimensionally regularized Feynman diagrams are represented by means of products of k-functions. The infinite part of these diagrams is found very easily, also if they are overlapping, and the separation of the several kinds of divergences comes out quite naturally. Ward identities are proven in a transparent way. Series expansions in terms of the external momenta and their inner products are possible

Phase diagrams of the elements

International Nuclear Information System (INIS)

Young, D.A.

1975-01-01

A summary of the pressure-temperature phase diagrams of the elements is presented, with graphs of the experimentally determined solid-solid phase boundaries and melting curves. Comments, including theoretical discussion, are provided for each diagram. The crystal structure of each solid phase is identified and discussed. This work is aimed at encouraging further experimental and theoretical research on phase transitions in the elements

Homotopy theory of modules over diagrams of rings

Directory of Open Access Journals (Sweden)

J. P. C. Greenlees

2014-09-01

Full Text Available Given a diagram of rings, one may consider the category of modules over them. We are interested in the homotopy theory of categories of this type: given a suitable diagram of model categories ℳ( (as runs through the diagram, we consider the category of diagrams where the object ( at comes from ℳ(. We develop model structures on such categories of diagrams and Quillen adjunctions that relate categories based on different diagram shapes. Under certain conditions, cellularizations (or right Bousfield localizations of these adjunctions induce Quillen equivalences. As an application we show that a cellularization of a category of modules over a diagram of ring spectra (or differential graded rings is Quillen equivalent to modules over the associated inverse limit of the rings. Another application of the general machinery here is given in work by the authors on algebraic models of rational equivariant spectra. Some of this material originally appeared in the preprint “An algebraic model for rational torus-equivariant stable homotopy theory”, arXiv:1101.2511, but has been generalized here.

The application of diagrams in architectural design

Directory of Open Access Journals (Sweden)

Dulić Olivera

2014-01-01

Full Text Available Diagrams in architecture represent the visualization of the thinking process, or selective abstraction of concepts or ideas translated into the form of drawings. In addition, they provide insight into the way of thinking about and in architecture, thus creating a balance between the visual and the conceptual. The subject of research presented in this paper are diagrams as a specific kind of architectural representation, and possibilities and importance of their application in the design process. Diagrams are almost old as architecture itself, and they are an element of some of the most important studies of architecture during all periods of history - which results in a large number of different definitions of diagrams, but also very different conceptualizations of their features, functions and applications. The diagrams become part of contemporary architectural discourse during the eighties and nineties of the twentieth century, especially through the work of architects like Bernard Tschumi, Peter Eisenman, Rem Koolhaas, SANAA and others. The use of diagrams in the design process allows unification of some of the essential aspects of the profession: architectural representation and design process, as well as the question of the concept of architectural and urban design at a time of rapid changes at all levels of contemporary society. The aim of the research is the analysis of the diagram as a specific medium for processing large amounts of information that the architect should consider and incorporate into the architectural work. On that basis, it is assumed that an architectural diagram allows the creator the identification and analysis of specific elements or ideas of physical form, thereby constantly maintaining concept of the integrity of the architectural work.

The 7 basic tools of quality applied to radiological safety

International Nuclear Information System (INIS)

Gonzalez F, J.A.

1991-01-01

This work seeks to establish a series of correspondences among the search of the quality and the optimization of the doses received by the occupationally exposed personnel. There are treated about the seven basic statistic tools of the quality: the Pareto technique, Cause effect diagrams, Stratification, Verification sheet, Histograms, Dispersion diagrams and Graphics and control frames applied to the Radiological Safety

Reading fitness landscape diagrams through HSAB concepts

Energy Technology Data Exchange (ETDEWEB)

Vigneresse, Jean-Louis, E-mail: jean-louis.vigneresse@univ-lorraine.fr

2014-10-31

Highlights: • Qualitative information from HSAB descriptors. • 2D–3D diagrams using chemical descriptors (χ, η, ω, α) and principles (MHP, mEP, mPP). • Estimate of the energy exchange during reaction paths. • Examples from complex systems (geochemistry). - Abstract: Fitness landscapes are conceived as range of mountains, with local peaks and valleys. In terms of potential, such topographic variations indicate places of local instability or stability. The chemical potential, or electronegativity, its value changed of sign, carries similar information. In addition to chemical descriptors defined through hard-soft acid-base (HSAB) concepts and computed through density functional theory (DFT), the principles that rule chemical reactions allow the design of such landscape diagrams. The simplest diagram uses electrophilicity and hardness as coordinates. It allows examining the influence of maximum hardness or minimum electrophilicity principles. A third dimension is introduced within such a diagram by mapping the topography of electronegativity, polarizability or charge exchange. Introducing charge exchange during chemical reactions, or mapping a third parameter (f.i. polarizability) reinforces the information carried by a simple binary diagram. Examples of such diagrams are provided, using data from Earth Sciences, simple oxides or ligands.

Selected topics on the nonrelativistic diagram technique

International Nuclear Information System (INIS)

Blokhintsev, L.D.; Narodetskij, I.M.

1983-01-01

The construction of the diagrams describing various processes in the four-particle systems is considered. It is shown that these diagrams, in particular the diagrams corresponding to the simple mechanisms often used in nuclear and atomic reaction theory, are readily obtained from the Faddeev-Yakubovsky equations. The covariant four-dimensional formalism of nonrelativistic Feynman graphs and its connection to the three-dimensional graph technique are briefly discussed

Drawing Euler Diagrams with Circles: The Theory of Piercings.

Science.gov (United States)

Stapleton, Gem; Leishi Zhang; Howse, John; Rodgers, Peter

2011-07-01

Euler diagrams are effective tools for visualizing set intersections. They have a large number of application areas ranging from statistical data analysis to software engineering. However, the automated generation of Euler diagrams has never been easy: given an abstract description of a required Euler diagram, it is computationally expensive to generate the diagram. Moreover, the generated diagrams represent sets by polygons, sometimes with quite irregular shapes that make the diagrams less comprehensible. In this paper, we address these two issues by developing the theory of piercings, where we define single piercing curves and double piercing curves. We prove that if a diagram can be built inductively by successively adding piercing curves under certain constraints, then it can be drawn with circles, which are more esthetically pleasing than arbitrary polygons. The theory of piercings is developed at the abstract level. In addition, we present a Java implementation that, given an inductively pierced abstract description, generates an Euler diagram consisting only of circles within polynomial time.

Multi-currency Influence Diagrams

DEFF Research Database (Denmark)

Nielsen, Søren Holbech; Nielsen, Thomas Dyhre; Jensen, Finn V.

2007-01-01

When using the influence diagrams framework for solving a decision problem with several different quantitative utilities, the traditional approach has been to convert the utilities into one common currency. This conversion is carried out using a tacit transformation, under the assumption...... that the converted problem is equivalent to the original one. In this paper we present an extension of the influence diagram framework. The extension allows for these decision problems to be modelled in their original form. We present an algorithm that, given a linear conversion function between the currencies...

Pourbaix Diagrams for Copper in 5 m Chloride Solution

International Nuclear Information System (INIS)

Beverskog, Bjoern; Pettersson, Sven-Olof

2002-12-01

Pourbaix diagrams for the copper in 5 molal chlorine at 5-100 deg C have been calculated. Predominance diagrams for dissolved copper containing species have also been calculated. Two different total concentrations of dissolved copper, 10 -4 and 10 -6 molal, have been used in the calculations. ChIoride is the predominating chlorine species in aqueous solutions. Therefore Pourbaix diagrams for chlorine can be used to discuss the effect of chloride solutions on the corrosion behavior of a metal. Presence of chloride increases the corrosion regions of copper at the expense of the immunity and passivity regions in the Pourbaix diagrams. Copper corrodes in 5 molal chloride by formation Of CuCl 3 2- in acid and alkaline solutions. At higher potentials in acid solutions CuCl 3 2- is oxidized to CuCl 2 (aq), which at increasing potentials can form CuCI + , Cu 2+ or CuClO 3 + . Copper passivates by formation of Cu 2 O(cr), CuO(cr), or CUO 2 3 Cu(OH) 2 (s). Cu 2 O(cr) does not form at [Cu(aq)] tot = 10 -6 molal in 5 m C1-, which results in a corrosion area between the immunity and passivity areas. Copper at the anticipated repository potentials and pH corrodes at 100 deg C at [Cu(aq)] tot = 10 -4 molal and at 80-100 deg C at [Cu(aq)] tot = 10 -6 molal. Copper at the anticipated repository potentials and pH can corrode at 80 deg C at [Cu(aq)] tot = 10 -4 molal and at 50 deg C at [Cu(aq)] tot = 10 -6 molal. The bentonite clay and copper canisters in the deep repository can be considered as a 'closed' system from macroscopic point of view. The clay barrier limits both inward diffusion of oxygen and aggressive anions as well as outward diffusion of corrosion products from the canisters. Both diffusion phenomena will drive the corrosion potential into the immunity area of the Pourbaix diagram for copper. The corrosion will thereby stop by an automatic mechanism. However, this is only valid if no macro cracks occur in the clay. The auto-stop is valid for the initial, main and

Shutdown Safety in NEK

International Nuclear Information System (INIS)

Gluhak, Mario; Senegovic, Marko

2014-01-01

Industry performance analysis since 2004 has revealed that 23% of the events reported to WANO occurred during outage periods. Given the fact that a plant is in the outage only 5 percent of the time, this emphasizes the importance of shutdown safety and measures station staffs undertake to maintain effective barriers to safety margins during the outage. Back in 1990s, the industry adopted guidance to meet safety requirements by focusing on safety functions. Both WANO and INPO released various documents, reports and guidelines to help accomplish those requirements. However, in the last decade inadequate 'defence in depth' has led to several events affecting shutdown safety and challenging one of the most important nuclear safety principles: 'The special characteristics of nuclear technology are taken into account in all decisions and actions. Reactivity control, continuity of core cooling, and integrity of fission product barriers are valued as essential, distinguishing attributes of nuclear station work environment'. NEK has recognized the importance of 'defence in depth'Industry performance analysis since 2004 has revealed that 23% of the events reported to WANO occurred during outage periods. Given the fact that a plant is in the outage only 5 percent of the time, this emphasizes the importance of shutdown safety and measures station staffs undertake to maintain effective barriers to safety margins during the outage. Back in 1990s, the industry adopted guidance to meet safety requirements by focusing on safety functions. Both WANO and INPO released various documents, reports and guidelines to help accomplish those requirements. However, in the last decade inadequate 'defence in depth' has led to several events affecting shutdown safety and challenging one of the most important nuclear safety principles: 'The special characteristics of nuclear technology are taken into account in all decisions and actions. Reactivity

Covariant diagrams for one-loop matching

International Nuclear Information System (INIS)

Zhang, Zhengkang

2016-10-01

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gaugecovariant quantities and are thus dubbed ''covariant diagrams.'' The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhengkang [Michigan Center for Theoretical Physics (MCTP), University of Michigan,450 Church Street, Ann Arbor, MI 48109 (United States); Deutsches Elektronen-Synchrotron (DESY),Notkestraße 85, 22607 Hamburg (Germany)

2017-05-30

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gauge-covariant quantities and are thus dubbed “covariant diagrams.” The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhengkang [Michigan Univ., Ann Arbor, MI (United States). Michigan Center for Theoretical Physics; Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany)

2016-10-15

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gaugecovariant quantities and are thus dubbed ''covariant diagrams.'' The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Covariant diagrams for one-loop matching

International Nuclear Information System (INIS)

Zhang, Zhengkang

2017-01-01

We present a diagrammatic formulation of recently-revived covariant functional approaches to one-loop matching from an ultraviolet (UV) theory to a low-energy effective field theory. Various terms following from a covariant derivative expansion (CDE) are represented by diagrams which, unlike conventional Feynman diagrams, involve gauge-covariant quantities and are thus dubbed “covariant diagrams.” The use of covariant diagrams helps organize and simplify one-loop matching calculations, which we illustrate with examples. Of particular interest is the derivation of UV model-independent universal results, which reduce matching calculations of specific UV models to applications of master formulas. We show how such derivation can be done in a more concise manner than the previous literature, and discuss how additional structures that are not directly captured by existing universal results, including mixed heavy-light loops, open covariant derivatives, and mixed statistics, can be easily accounted for.

Students’ learning activities while studying biological process diagrams

NARCIS (Netherlands)

Kragten, M.; Admiraal, W.; Rijlaarsdam, G.

2015-01-01

Process diagrams describe how a system functions (e.g. photosynthesis) and are an important type of representation in Biology education. In the present study, we examined students’ learning activities while studying process diagrams, related to their resulting comprehension of these diagrams. Each

Dynamic simulation of collisions of heavy high-speed trucks with concrete barriers

International Nuclear Information System (INIS)

Itoh, Yoshito; Liu, Chunlu; Kusama, Ryuichi

2007-01-01

Real vehicle collision experiments on full-scale road safety barriers are important to determine the outcome of a vehicle versus barrier impact accident. However, such experiments require large investment of time and money. Numerical simulation has therefore been imperative as an alternative method for testing concrete barriers. In this research, spring subgrade models were first developed to simulate the ground boundary of concrete barriers. Both heavy trucks and concrete barriers were modeled using finite element methods (FEM) to simulate dynamic collision performances. Comparison of the results generated from computer simulations and on-site full-scale experiments demonstrated that the developed models could be applied to simulate the collision of heavy trucks with concrete barriers to provide the data to design new road safety barriers and analyze existing ones

Operations space diagram for ECRH and ECCD

International Nuclear Information System (INIS)

Bindslev, Henrik

2004-01-01

A Clemmov-Mullaly-Allis (CMA) type diagram, the ECW-CMA diagram, for representing the operational possibilities of electron cyclotron heating and current drive (ECRH/ECCD) systems for fusion plasmas is presented. In this diagram, with normalized density and normalized magnetic field coordinates, the parameter range in which it is possible to achieve a given task (e.g. O-mode current drive for stabilizing a neoclassical tearing mode) appears as a region. With also the Greenwald density limit shown, this diagram condenses the information on operational possibilities, facilitating the overview required at the design phase. At the operations phase it may also prove useful in setting up experimental scenarios by showing operational possibilities, avoiding the need for survey type ray-tracing at the initial planning stages. The diagram may also serve the purpose of communicating operational possibilities to non-experts. JET and ITER like plasmas are used, but the method is generic. (author)

Near threshold expansion of Feynman diagrams

International Nuclear Information System (INIS)

Mendels, E.

2005-01-01

The near threshold expansion of Feynman diagrams is derived from their configuration space representation, by performing all x integrations. The general scalar Feynman diagram is considered, with an arbitrary number of external momenta, an arbitrary number of internal lines and an arbitrary number of loops, in n dimensions and all masses may be different. The expansions are considered both below and above threshold. Rules, giving real and imaginary part, are derived. Unitarity of a sunset diagram with I internal lines is checked in a direct way by showing that its imaginary part is equal to the phase space integral of I particles

On the question of calculation methods of phase diagrams

International Nuclear Information System (INIS)

Vasil'ev, M.V.

1983-01-01

The technique of determining interaction parameters of components of binary alloys is suggested. U-Mo and Cu-Al systems are used as example with the aid of experimental state diagrams. It is shown that the search for new regularities is necessary with the aim of analytical description of state diagrams and forecast of the shape of phase equilibria curves in real systems. Optimum combinations of experimental investigations with the aim of reliable determination of supporting points and forecasting possibilities of typical equations can considerably decrease the volume of experimental work when preparing state diagrams, in cases of repeated state diagrams of more reliable state diagrams with the application of more advanced methods of investigation. The translation of state diagrams from geometric to analytical language with the use of typical equations opens up new possibilities for establishing a compact information bank for state diagrams

A geometric proof of confluence by decreasing diagrams

NARCIS (Netherlands)

Klop, J.W.; Oostrom, V. van; Vrijer, R. de

The criterion for confluence using decreasing diagrams is a generalization of several well-known confluence criteria in abstract rewriting, such as the strong confluence lemma. We give a new proof of the decreasing diagram theorem based on a geometric study of in finite reduction diagrams, arising

Compact flow diagrams for state sequences

NARCIS (Netherlands)

Buchin, K.A.; Buchin, M.E.; Gudmundsson, J.; Horton, M.J.; Sijben, S.

2016-01-01

We introduce the concept of compactly representing a large number of state sequences, e.g., sequences of activities, as a flow diagram. We argue that the flow diagram representation gives an intuitive summary that allows the user to detect patterns among large sets of state sequences. Simplified,

Voronoi diagram and microstructure of weldment

Energy Technology Data Exchange (ETDEWEB)

Cho, Jung Ho [Chungbuk National University, Cheongju (Korea, Republic of)

2015-01-15

Voronoi diagram, one of the well-known space decomposition algorithms has been applied to express the microstructure of a weldment for the first time due to the superficial analogy between a Voronoi cell and a metal's grain. The area of the Voronoi cells can be controlled by location and the number of the seed points. This can be correlated to the grain size in the microstructure and the number of nuclei formed. The feasibility of representing coarse and fine grain structures were tested through Voronoi diagrams and it is applied to expression of cross-sectional bead shape of a typical laser welding. As result, it successfully described coarsened grain size of heat affected zone and columnar crystals in fusion zone. Although Voronoi diagram showed potential as a microstructure prediction tool through this feasible trial but direct correlation control variable of Voronoi diagram to solidification process parameter is still remained as further works.

The role of perceptual cues in matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; van Amelsvoort, Marije; Anjewierden, A.

An experiment was conducted to assess whether the design of a matrix diagram influences how people study the diagram and whether this has an effect on recall of the presented information. We compared four versions of a matrix diagram on antisocial personality disorder. It consisted of four header

The role of perceptual cues in matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; Amelsvoort, Marije; Anjewierden, Anjo Allert

2015-01-01

An experiment was conducted to assess whether the design of a matrix diagram influences how people study the diagram and whether this has an effect on recall of the presented information. We compared four versions of a matrix diagram on antisocial personality disorder. It consisted of four header

The Eh-pH Diagram and Its Advances

Directory of Open Access Journals (Sweden)

Hsin-Hsiung Huang

2016-01-01

Full Text Available Since Pourbaix presented Eh versus pH diagrams in his “Atlas of Electrochemical Equilibria in Aqueous Solution”, diagrams have become extremely popular and are now used in almost every scientific area related to aqueous chemistry. Due to advances in personal computers, such diagrams can now show effects not only of Eh and pH, but also of variables, including ligand(s, temperature and pressure. Examples from various fields are illustrated in this paper. Examples include geochemical formation, corrosion and passivation, precipitation and adsorption for water treatment and leaching and metal recovery for hydrometallurgy. Two basic methods were developed to construct an Eh-pH diagram concerning the ligand component(s. The first method calculates and draws a line between two adjacent species based on their given activities. The second method performs equilibrium calculations over an array of points (500 × 800 or higher are preferred, each representing one Eh and one pH value for the whole system, then combines areas of each dominant species for the diagram. These two methods may produce different diagrams. The fundamental theories, illustrated results, comparison and required conditions behind these two methods are presented and discussed in this paper. The Gibbs phase rule equation for an Eh-pH diagram was derived and verified from actual plots. Besides indicating the stability area of water, an Eh-pH diagram normally shows only half of an overall reaction. However, merging two or more related diagrams together reveals more clearly the possibility of the reactions involved. For instance, leaching of Au with cyanide followed by cementing Au with Zn (Merrill-Crowe process can be illustrated by combining Au-CN and Zn-CN diagrams together. A second example of the galvanic conversion of chalcopyrite can be explained by merging S, Fe–S and Cu–Fe–S diagrams. The calculation of an Eh-pH diagram can be extended easily into another dimension, such

Compact flow diagrams for state sequences

NARCIS (Netherlands)

Buchin, Kevin; Buchin, Maike; Gudmundsson, Joachim; Horton, Michael; Sijben, Stef

2017-01-01

We introduce the concept of using a flow diagram to compactly represent the segmentation of a large number of state sequences according to a set of criteria. We argue that this flow diagram representation gives an intuitive summary that allows the user to detect patterns within the segmentations. In

Barriers to Physical Activity in East Harlem, New York

Directory of Open Access Journals (Sweden)

Ashley M. Fox

2012-01-01

Full Text Available Background. East Harlem is an epicenter of the intertwining epidemics of obesity and diabetes in New York. Physical activity is thought to prevent and control a number of chronic illnesses, including diabetes, both independently and through weight control. Using data from a survey collected on adult (age 18+ residents of East Harlem, this study evaluated whether perceptions of safety and community-identified barriers were associated with lower levels of physical activity in a diverse sample. Methods. We surveyed 300 adults in a 2-census tract area of East Harlem and took measurements of height and weight. Physical activity was measured in two ways: respondents were classified as having met the weekly recommended target of 2.5 hours of moderate physical activity (walking per week (or not and reporting having engaged in at least one recreational physical activity (or not. Perceived barriers were assessed through five items developed by a community advisory board and perceptions of neighborhood safety were measured through an adapted 7-item scale. Two multivariate logistic regression models with perceived barriers and concerns about neighborhood safety were modeled separately as predictors of engaging in recommended levels of exercise and recreational physical activity, controlling for respondent weight and sociodemographic characteristics. Results. The most commonly reported perceived barriers to physical activity identified by nearly half of the sample were being too tired or having little energy followed by pain with exertion and lack of time. Multivariate regression found that individuals who endorsed a greater number of perceived barriers were less likely to report having met their weekly recommended levels of physical activity and less likely to engage in recreational physical activity controlling for covariates. Concerns about neighborhood safety, though prevalent, were not associated with physical activity levels. Conclusions. Although

What stage are low-income and middle-income countries (LMICs) at with patient safety curriculum implementation and what are the barriers to implementation? A two-stage cross-sectional study

Science.gov (United States)

Ginsburg, Liane R; Dhingra-Kumar, Neelam; Donaldson, Liam J

2017-01-01

Objectives The improvement of safety in healthcare worldwide depends in part on the knowledge, skills and attitudes of staff providing care. Greater patient safety content in health professional education and training programmes has been advocated internationally. While WHO Patient Safety Curriculum Guides (for Medical Schools and Multi-Professional Curricula) have been widely disseminated in low-income and middle-income countries (LMICs) over the last several years, little is known about patient safety curriculum implementation beyond high-income countries. The present study examines patient safety curriculum implementation in LMICs. Methods Two cross-sectional surveys were carried out. First, 88 technical officers in Ministries of Health and WHO country offices were surveyed to identify the pattern of patient safety curricula at country level. A second survey followed that gathered information from 71 people in a position to provide institution-level perspectives on patient safety curriculum implementation. Results The majority, 69% (30/44), of the countries were either considering whether to implement a patient safety curriculum or actively planning, rather than actually implementing, or embedding one. Most organisations recognised the need for patient safety education and training and felt a safety curriculum was compatible with the values of their organisation; however, important faculty-level barriers to patient safety curriculum implementation were identified. Key structural markers, such as dedicated financial resources and relevant assessment tools to evaluate trainees’ patient safety knowledge and skills, were in place in fewer than half of organisations studied. Conclusions Greater attention to patient safety curriculum implementation is needed. The barriers to patient safety curriculum implementation we identified in LMICs are not unique to these regions. We propose a framework to act as a global standard for patient safety curriculum implementation

Diagrams of natural deductions

Energy Technology Data Exchange (ETDEWEB)

Popov, S V

1982-01-01

The concept of natural deductions was investigated by the author in his analysis of the complexity of deductions in propositional computations (1975). Here some natural deduction systems are considered, and an analytical procedure proposed which results in a deduction diagram for each system. Each diagram takes the form of an orientated, charge graph, features of which can be used to establish the equivalence of classes of deductions. For each of the natural deduction systems considered, a system of equivalent transformation schemes is derived, which is complete with respect to the given definition of equivalence. 2 references.

Comparison of residual strength-grounding damage index diagrams for tankers produced by the ALPS/HULL ISFEM and design formula method

Directory of Open Access Journals (Sweden)

Do Kyun Kim

2013-03-01

Full Text Available This study compares the Residual ultimate longitudinal strength – grounding Damage index (R-D diagrams produced by two analysis methods: the ALPS/HULL Intelligent Supersize Finite Element Method (ISFEM and the design formula (modified Paik and Mansour method – used to assess the safety of damaged ships. The comparison includes four types of double-hull oil tankers: Panamax, Aframax, Suezmax and VLCC. The R-D diagrams were calculated for a series of 50 grounding scenarios. The diagrams were efficiently sampled using the Latin Hypercube Sampling (LHS technique and comprehensively analysed based on ship size. Finally, the two methods were compared by statistically analysing the differences between their grounding damage indices and ultimate longitudinal strength predictions. The findings provide a useful example of how to apply the ultimate longitudinal strength analysis method to grounded ships.

Control wiring diagrams

International Nuclear Information System (INIS)

McCauley, T.M.; Eskinazi, M.; Henson, L.L.

1989-01-01

This paper discusses the changes in electrical document requirements that occur when construction is complete and a generating station starts commercial operation. The needs of operations and maintenance (O and M) personnel are analyzed and contrasted with those of construction to illustrate areas in which the construction documents (drawings, diagrams, and databases) are difficult to use for work at an operating station. The paper discusses the O and M electrical documents that the Arizona Nuclear Power Project (ANPP) believes are most beneficial for the three operating units at Palo Verde; these are control wiring diagrams and an associated document cross-reference list. The benefits offered by these new, station O and M-oriented documents are weighted against the cost of their creation and their impact on drawing maintenance

New detectors for powders diagrams

International Nuclear Information System (INIS)

Convert, P.

1975-01-01

During the last few years, all the classical neutron diffractometers for powders have used one or maybe a few counters. So, it takes a long time to obtain a diagram which causes many disadvantages: 1) very long experiments: one or two days (or flux on the sample about 10 6 n/cm 2 /a); 2) necessity of big samples: many cm 3 ; 3) necessity of having the whole diagram before changing anything in the experiment: magnetic field, temperature, quality of the sample; 4) necessity of having collimators of a few times ten minutes to obtain correct statistics in the diagram. Because of these disadvantages, several attempts have been made to speed up the experimental procedure such as using more counters, the detection of neutrons on a resistive wire, etc. In Grenoble, new position-sensitive detectors have been constructed using a digital technique

Functionality of road safety devices – identification and analysis of factors

Directory of Open Access Journals (Sweden)

Jeliński Łukasz

2017-01-01

Full Text Available Road safety devices are designed to protect road users from the risk of injury or death. The principal type of restraint is the safety barrier. Deployed on sites with the highest risk of run-off-road accidents, safety barriers are mostly found on bridges, flyovers, central reservations, and on road edges which have fixed obstacles next to them. If properly designed and installed, safety barriers just as other road safety devices, should meet a number of functional features. This report analyses factors which may deteriorate functionality, ways to prevent this from happening and the thresholds for loss of road safety device functionality.

Causal Diagrams for Empirical Research

OpenAIRE

Pearl, Judea

1994-01-01

The primary aim of this paper is to show how graphical models can be used as a mathematical language for integrating statistical and subject-matter information. In particular, the paper develops a principled, nonparametric framework for causal inference, in which diagrams are queried to determine if the assumptions available are sufficient for identifiying causal effects from non-experimental data. If so the diagrams can be queried to produce mathematical expressions for causal effects in ter...

Graphical matching rules for cardinality based service feature diagrams

Directory of Open Access Journals (Sweden)

Faiza Kanwal

2017-03-01

Full Text Available To provide efficient services to end-users, variability and commonality among the features of the product line is a challenge for industrialist and researchers. Feature modeling provides great services to deal with variability and commonality among the features of product line. Cardinality based service feature diagrams changed the basic framework of service feature diagrams by putting constraints to them, which make service specifications more flexible, but apart from their variation in selection third party services may have to be customizable. Although to control variability, cardinality based service feature diagrams provide high level visual notations. For specifying variability, the use of cardinality based service feature diagrams raises the problem of matching a required feature diagram against the set of provided diagrams.

Quantitative occupational risk model: Single hazard

International Nuclear Information System (INIS)

Papazoglou, I.A.; Aneziris, O.N.; Bellamy, L.J.; Ale, B.J.M.; Oh, J.

2017-01-01

A model for the quantification of occupational risk of a worker exposed to a single hazard is presented. The model connects the working conditions and worker behaviour to the probability of an accident resulting into one of three types of consequence: recoverable injury, permanent injury and death. Working conditions and safety barriers in place to reduce the likelihood of an accident are included. Logical connections are modelled through an influence diagram. Quantification of the model is based on two sources of information: a) number of accidents observed over a period of time and b) assessment of exposure data of activities and working conditions over the same period of time and the same working population. Effectiveness of risk reducing measures affecting the working conditions, worker behaviour and/or safety barriers can be quantified through the effect of these measures on occupational risk. - Highlights: • Quantification of occupational risk from a single hazard. • Influence diagram connects working conditions, worker behaviour and safety barriers. • Necessary data include the number of accidents and the total exposure of worker • Effectiveness of risk reducing measures is quantified through the impact on the risk • An example illustrates the methodology.

Fusion safety data base

International Nuclear Information System (INIS)

Laats, E.T.; Hardy, H.A.

1983-01-01

The purpose of this Fusion Safety Data Base Program is to provide a repository of data for the design and development of safe commercial fusion reactors. The program is sponsored by the United States Department of Energy (DOE), Office of Fusion Energy. The function of the program is to collect, examine, permanently store, and make available the safety data to the entire US magnetic-fusion energy community. The sources of data will include domestic and foreign fusion reactor safety-related research programs. Any participant in the DOE Program may use the Data Base Program from his terminal through user friendly dialog and can view the contents in the form of text, tables, graphs, or system diagrams

Mort User's Manual: For use with the Management Oversight and Risk Tree analytical logic diagram

Energy Technology Data Exchange (ETDEWEB)

Knox, N.W.; Eicher, R.W.

1992-02-01

This report contains the User's Manual for MORT (Management Oversight and Risk Tree), a logic diagram in the form of a work sheet'' that illustrates a long series of interrelated questions. MORT is a comprehensive analytical procedure that provides a disciplined method for determining the causes and contributing factors of major accidents. Alternatively, it serves as a tool to evaluate the quality of an existing system. While similar in many respects to fault tree analysis, MORT is more generalized and presents over 1500 specific elements of an ideal universal'' management program for optimizing environment, safety and health, and other programs. This User's Manual is intended to be used with the MORT diagram dated February 1992.

On the Impact of Layout Quality to Understanding UML Diagrams: Diagram Type and Expertise

DEFF Research Database (Denmark)

Störrle, Harald

2012-01-01

Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only. In the ......Practical experience suggests that the use and understanding of UML diagrams is greatly affected by the quality of their layout. In previous work, we have presented evidence supporting this intuition. This contrasts with earlier experiments that yielded weak or inconclusive evidence only...

Y-12 Plant Remedial Action technology logic diagram. Volume I: Technology evaluation

International Nuclear Information System (INIS)

1994-09-01

The Y-12 Plant Remedial Action Program addresses remediation of the contaminated groundwater, surface water and soil in the following areas located on the Oak Ridge Reservation: Chestnut Ridge, Bear Creek Valley, the Upper and Lower East Fork Popular Creek Watersheds, CAPCA 1, which includes several areas in which remediation has been completed, and CAPCA 2, which includes dense nonaqueous phase liquid wells and a storage facility. There are many facilities within these areas that are contaminated by uranium, mercury, organics, and other materials. This Technology Logic Diagram identifies possible remediation technologies that can be applied to the soil, water, and contaminants for characterization, treatment, and waste management technology options are supplemented by identification of possible robotics or automation technologies. These would facilitate the cleanup effort by improving safety, of remediation, improving the final remediation product, or decreasing the remediation cost. The Technology Logic Diagram was prepared by a diverse group of more than 35 scientists and engineers from across the Oak Ridge Reservation. Most are specialists in the areas of their contributions. 22 refs., 25 tabs

Beyond Feynman Diagrams (1/3)

CERN Multimedia

CERN. Geneva

2013-01-01

For decades the central theoretical tool for computing scattering amplitudes has been the Feynman diagram. However, Feynman diagrams are just too slow, even on fast computers, to be able to go beyond the leading order in QCD, for complicated events with many jets of hadrons in the final state. Such events are produced copiously at the LHC, and constitute formidable backgrounds to many searches for new physics. Over the past few years, alternative methods that go beyond ...

Wind Diagrams in Medieval Iceland

DEFF Research Database (Denmark)

Kedwards, Dale

2014-01-01

This article presents a study of the sole wind diagram that survives from medieval Iceland, preserved in the encyclopaedic miscellany in Copenhagen's Arnamagnæan Institute with the shelf mark AM 732b 4to (c. 1300-25). It examines the wind diagram and its accompanying text, an excerpt on the winds...... from Isidore of Seville's Etymologies. It also examines the perimeter of winds on two medieval Icelandic world maps, and the visual traditions from which they draw....

Bayesian Networks and Influence Diagrams

DEFF Research Database (Denmark)

Kjærulff, Uffe Bro; Madsen, Anders Læsø

 Probabilistic networks, also known as Bayesian networks and influence diagrams, have become one of the most promising technologies in the area of applied artificial intelligence, offering intuitive, efficient, and reliable methods for diagnosis, prediction, decision making, classification......, troubleshooting, and data mining under uncertainty. Bayesian Networks and Influence Diagrams: A Guide to Construction and Analysis provides a comprehensive guide for practitioners who wish to understand, construct, and analyze intelligent systems for decision support based on probabilistic networks. Intended...

Proof test diagrams for Zerodur glass-ceramic

Science.gov (United States)

Tucker, D. S.

1991-01-01

Proof test diagrams for Zerodur glass-ceramics are calculated from available fracture mechanics data. It is shown that the environment has a large effect on minimum time-to-failure as predicted by proof test diagrams.

Atlas of hot isostatic beryllium powder pressing diagrams

International Nuclear Information System (INIS)

Stoev, P.I.; Papirov, I.I.; Tikhinskij, G.F.; Vasil'ev, A.A.

1995-01-01

Diagrams of hot isotopic pressing (HIP) of beryllium powder with different grain size in a wide range of pressing parameters are built by mathematical modeling methods. The HIP diagrams presented are divided into 3 groups: parametric dependencies D=f(P,T); technological HIP diagrams; compacting mechanisms. The created data bank permits to optimise beryllium powder HIP with changing parameters. 4 refs., 23 figs

Barriers to and drivers for UK bioenergy development

Energy Technology Data Exchange (ETDEWEB)

Adams, P.W.; Mezzullo, W.G. [Department of Mechanical Engineering, Faculty of Engineering and Design, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Hammond, G.P.; McManus, M.C. [Department of Mechanical Engineering, Faculty of Engineering and Design, University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom); Institute for Sustainable Energy and Environment (I.SEE), University of Bath, Claverton Down, Bath BA2 7AY (United Kingdom)

2011-02-15

Barriers to UK bioenergy development arise from a number of technical, financial, social and other constraints. Likewise, the drivers for using bioenergy are numerous and diverse. A range of these barriers and drivers have been identified through a comprehensive literature and case study review, and then assessed through an online questionnaire, completed by stakeholders from across the UK bioenergy industry: farmers/suppliers, developers/owners of bioenergy projects, primary end-users, and government/policy stakeholders. The results are presented in the form of 'spider web' diagrams. The most critical barriers and drivers relate to economic factors of bioenergy projects. Farmers/suppliers and developers are influenced by production costs and benefits, whilst primary end-users of bioenergy are concerned mainly with the cost of purchasing energy resources. Common drivers for all stakeholders were found to be reducing carbon emissions and the dependency on fossil fuels. In order to satisfy the needs of stakeholders schemes must be both economically attractive and environmentally sustainable for projects to be successful. (author)

Pourbaix Diagrams for Copper in 5 m Chloride Solution

Energy Technology Data Exchange (ETDEWEB)

Beverskog, Bjoern [OECD Halden Reactor Project (Norway); Pettersson, Sven-Olof [ChemIT, Nykoeping (Sweden)

2002-12-01

Pourbaix diagrams for the copper in 5 molal chlorine at 5-100 deg C have been calculated. Predominance diagrams for dissolved copper containing species have also been calculated. Two different total concentrations of dissolved copper, 10{sup -4} and 10{sup -6} molal, have been used in the calculations. ChIoride is the predominating chlorine species in aqueous solutions. Therefore Pourbaix diagrams for chlorine can be used to discuss the effect of chloride solutions on the corrosion behavior of a metal. Presence of chloride increases the corrosion regions of copper at the expense of the immunity and passivity regions in the Pourbaix diagrams. Copper corrodes in 5 molal chloride by formation Of CuCl{sub 3}{sup 2-} in acid and alkaline solutions. At higher potentials in acid solutions CuCl{sub 3}{sup 2-} is oxidized to CuCl{sub 2}(aq), which at increasing potentials can form CuCI{sup +}, Cu{sup 2+} or CuClO{sub 3}{sup +}. Copper passivates by formation of Cu{sub 2}O(cr), CuO(cr), or CUO{sub 2} 3 Cu(OH){sub 2}(s). Cu{sub 2}O(cr) does not form at [Cu(aq)]{sub tot} = 10{sup -6} molal in 5 m C1-, which results in a corrosion area between the immunity and passivity areas. Copper at the anticipated repository potentials and pH corrodes at 100 deg C at [Cu(aq)]{sub tot} = 10{sup -4} molal and at 80-100 deg C at [Cu(aq)]{sub tot} = 10{sup -6} molal. Copper at the anticipated repository potentials and pH can corrode at 80 deg C at [Cu(aq)]{sub tot} = 10{sup -4} molal and at 50 deg C at [Cu(aq)]{sub tot} = 10{sup -6} molal. The bentonite clay and copper canisters in the deep repository can be considered as a 'closed' system from macroscopic point of view. The clay barrier limits both inward diffusion of oxygen and aggressive anions as well as outward diffusion of corrosion products from the canisters. Both diffusion phenomena will drive the corrosion potential into the immunity area of the Pourbaix diagram for copper. The corrosion will thereby stop by an automatic

75 FR 49536 - Petitions for Modification of Existing Mandatory Safety Standards

Science.gov (United States)

2010-08-13

... wells utilizing the following terms and conditions: 1. District Manager Approval; (a) a safety barrier.... After District Manager approval, the mine operator will then mine within the safety barrier of the well... DEPARTMENT OF LABOR Mine Safety and Health Administration Petitions for Modification of Existing...

Visualizing Metrics on Areas of Interest in Software Architecture Diagrams

NARCIS (Netherlands)

Byelas, Heorhiy; Telea, Alexandru; Eades, P; Ertl, T; Shen, HW

2009-01-01

We present a new method for the combined visualization of software architecture diagrams, Such as UML class diagrams or component diagrams, and software metrics defined on groups of diagram elements. Our method extends an existing rendering technique for the so-called areas of interest in system

Updating the Nomographical Diagrams for Dimensioning the Beams

Directory of Open Access Journals (Sweden)

Pop Maria T.

2015-12-01

Full Text Available In order to reduce the time period needed for structures design it is strongly recommended to use nomographical diagrams. The base for formation and updating the nomographical diagrams, stands on the charts presented by different technical publications. The updated charts use the same algorithm and calculation elements as the former diagrams in accordance to the latest prescriptions and European standards. The result consists in a chart, having the same properties, similar with the nomogragraphical diagrams already in us. As a general conclusion, even in our days, the nomographical diagrams are very easy to use. Taking into consideration the value of the moment it’s easy to find out the necessary reinforcement area and vice-verse, having the reinforcement area you can find out the capable moment. It still remains a useful opportunity for pre-sizing and designs the reinforced concrete sections.

A variable ordering heuristic for risk monitors based on zero-suppressed binary decision diagram

International Nuclear Information System (INIS)

Wang Jin; Wang Fang; Wang Jiaqun; Gu Xiaohui; Yuan Run; Li Yazhou; Hu Liqin; Wu Yican; Yin Yuan; FDS Team

2010-01-01

The probabilistic safety assessment model using for determining the instantaneous risk in a risk monitor are much more complex than the operational model using for determining the average risk. Therefore the development of a fast calculation engine is indispensable and challengeable. the scale of zero-suppressed binary decision diagram. In this paper an optimized method of variables ordering, which fully utilized that features of operational model, was proposed.Not only the theoretical demonstration but also the applications were also brought out. (authors)

Master Logic Diagram: An Approach to Identify Initiating Events of HTGRs

Science.gov (United States)

Purba, J. H.

2018-02-01

Initiating events of a nuclear power plant being evaluated need to be firstly identified prior to applying probabilistic safety assessment on that plant. Various types of master logic diagrams (MLDs) have been proposedforsearching initiating events of the next generation of nuclear power plants, which have limited data and operating experiences. Those MLDs are different in the number of steps or levels and different in the basis for developing them. This study proposed another type of MLD approach to find high temperature gas cooled reactor (HTGR) initiating events. It consists of five functional steps starting from the top event representing the final objective of the safety functions to the basic event representing the goal of the MLD development, which is an initiating event. The application of the proposed approach to search for two HTGR initiating events, i.e. power turbine generator trip and loss of offsite power, is provided. The results confirmed that the proposed MLD is feasiblefor finding HTGR initiating events.

Phase diagram of classical electronic bilayers

International Nuclear Information System (INIS)

Ranganathan, S; Johnson, R E

2006-01-01

Extensive molecular dynamics calculations have been performed on classical, symmetric electronic bilayers at various values of the coupling strength Γ and interlayer separation d to delineate its phase diagram in the Γ-d plane. We studied the diffusion, the amplitude of the main peak of the intralayer static structure factor and the peak positions of the intralayer pair correlation function with the aim of defining equivalent signatures of freezing and constructing the resulting phase diagram. It is found that for Γ greater than 75, crystalline structures exist for a certain range of interlayer separations, while liquid phases are favoured at smaller and larger d. It is seen that there is good agreement between our phase diagram and previously published ones

Phase diagram of classical electronic bilayers

Energy Technology Data Exchange (ETDEWEB)

Ranganathan, S [Department of Physics, Royal Military College of Canada, Kingston, Ontario K7K 7B4 (Canada); Johnson, R E [Department of Mathematics and Computer Science, Royal Military College of Canada, Kingston, Ontario K7K 7B4 (Canada)

2006-04-28

Extensive molecular dynamics calculations have been performed on classical, symmetric electronic bilayers at various values of the coupling strength {gamma} and interlayer separation d to delineate its phase diagram in the {gamma}-d plane. We studied the diffusion, the amplitude of the main peak of the intralayer static structure factor and the peak positions of the intralayer pair correlation function with the aim of defining equivalent signatures of freezing and constructing the resulting phase diagram. It is found that for {gamma} greater than 75, crystalline structures exist for a certain range of interlayer separations, while liquid phases are favoured at smaller and larger d. It is seen that there is good agreement between our phase diagram and previously published ones.

Engineered barrier systems (EBS): design requirements and constraints

International Nuclear Information System (INIS)

2004-01-01

A joint NEA-EC workshop entitled 'Engineered Barrier Systems: Design Requirements and Constraints' was organised in Turku, Finland on 26-29 August 2003 and hosted by Posiva Oy. The main objectives of the workshop were to promote interaction and collaboration among experts responsible for engineering design and safety assessment in order to develop a greater understanding of how to achieve the integration needed for the successful design of engineered barrier systems, and to clarify the role that an EBS can play in the overall safety case for a repository. These proceedings present the outcomes of this workshop. (author)

Development of a methodology for an environmental safety case in the United Kingdom

International Nuclear Information System (INIS)

Bailey, L.E.F.

2008-01-01

This presentation introduced the notion of an environmental safety case that focuses on the protection of both humans and the environment. The UK safety case will address operational, transport and post-closure safety for intermediate-level waste (ILW) and high-level waste (HLW). As there is yet no agreed site or design for a deep geological repository in the UK, the first iteration of the safety case will be generic, drawing on examples from international repository concepts. These concepts will be considered in appropriate generic geological environments typical of those found in the UK. The performance of these example concepts will be assessed using a time frames-based approach that focuses on the evolution of the multiple barriers and their associated safety functions. This approach recognizes that the relative importance of the different barriers in providing safety will evolve over time. For example, at early times the engineered barriers provide containment and the geological barriers protect the engineered barriers and provide isolation of the wastes. At later times, as the engineered barriers degrade, the geosphere provides the major barrier to radionuclide migration back to the surface and ensures the long-term stability of the system. A multi-factor safety case will be presented, using multiple lines of reasoning, including comparisons with natural and anthropogenic analogues, to provide assurance of the intrinsic safety functions of the system and their evolution over time. (author)

Modeling cancer registration processes with an enhanced activity diagram.

Science.gov (United States)

Lyalin, D; Williams, W

2005-01-01

Adequate instruments are needed to reflect the complexity of routine cancer registry operations properly in a business model. The activity diagram is a key instrument of the Unified Modeling Language (UML) for the modeling of business processes. The authors aim to improve descriptions of processes in cancer registration, as well as in other public health domains, through the enhancements of an activity diagram notation within the standard semantics of UML. The authors introduced the practical approach to enhance a conventional UML activity diagram, complementing it with the following business process concepts: timeline, duration for individual activities, responsibilities for individual activities within swimlanes, and descriptive text. The authors used an enhanced activity diagram for modeling surveillance processes in the cancer registration domain. Specific example illustrates the use of an enhanced activity diagram to visualize a process of linking cancer registry records with external mortality files. Enhanced activity diagram allows for the addition of more business concepts to a single diagram and can improve descriptions of processes in cancer registration, as well as in other domains. Additional features of an enhanced activity diagram allow to advance the visualization of cancer registration processes. That, in turn, promotes the clarification of issues related to the process timeline, responsibilities for particular operations, and collaborations among process participants. Our first experiences in a cancer registry best practices development workshop setting support the usefulness of such an approach.

Study on structural seismic margin and probabilistic seismic risk. Development of a structural capacity-seismic risk diagram

International Nuclear Information System (INIS)

Nakajima, Masato; Ohtori, Yasuki; Hirata, Kazuta

2010-01-01

Seismic margin is extremely important index and information when we evaluate and account seismic safety of critical structures, systems and components quantitatively. Therefore, it is required that electric power companies evaluate the seismic margin of each plant in back-check of nuclear power plants in Japan. The seismic margin of structures is usually defined as a structural capacity margin corresponding to design earthquake ground motion. However, there is little agreement as to the definition of the seismic margin and we have no knowledge about a relationship between the seismic margin and seismic risk (annual failure probability) which is obtained in PSA (Probabilistic Safety Assessment). The purpose of this report is to discuss a definition of structural seismic margin and to develop a diagram which can identify a relation between seismic margin and seismic risk. The main results of this paper are described as follows: (1) We develop seismic margin which is defined based on the fact that intensity of earthquake ground motion is more appropriate than the conventional definition (i.e., the response-based seismic margin) for the following reasons: -seismic margin based on earthquake ground motion is invariant where different typed structures are considered, -stakeholders can understand the seismic margin based on the earthquake ground motion better than the response-based one. (2) The developed seismic margin-risk diagram facilitates us to judge easily whether we need to perform detailed probabilistic risk analysis or only deterministic analysis, given that the reference risk level although information on the uncertainty parameter beta is not obtained. (3) We have performed numerical simulations based on the developed method for four sites in Japan. The structural capacity-risk diagram differs depending on each location because the diagram is greatly influenced by seismic hazard information for a target site. Furthermore, the required structural capacity

Calculation and definition of safety indicators

International Nuclear Information System (INIS)

Cristian, I.; Branzeu, N.; Vidican, D.; Vladescu, G.

1997-01-01

This paper presents, based on Cernavoda safety indicators proposal, the purpose definition and calculation formulas for each of the selected safety indicators. Five categories of safety indicators for Cernavoda Unit 1 were identified, namely: overall plant safety performance; initiating events; safety system availability, physical barrier integrity; indirect indicators. Definition, calculation and use of some safety indicators are shown in a tabular form. (authors)

Fishbone Diagrams: Organize Reading Content with a "Bare Bones" Strategy

Science.gov (United States)

Clary, Renee; Wandersee, James

2010-01-01

Fishbone diagrams, also known as Ishikawa diagrams or cause-and-effect diagrams, are one of the many problem-solving tools created by Dr. Kaoru Ishikawa, a University of Tokyo professor. Part of the brilliance of Ishikawa's idea resides in the simplicity and practicality of the diagram's basic model--a fish's skeleton. This article describes how…

Muonium and the Breit-Rabi diagram

International Nuclear Information System (INIS)

Cox, S.F.J.

1984-01-01

This chapter introduces the study of muonium, as opposed to that of unbound muons. The properties and behaviour of muonium are compared and contrasted with those of hydrogen and of positronium. The special significance of muonium in atomic and molecular physics is explained, and its utility as a lightweight or radioactive isotope of hydrogen in solid state physics and chemistry illustrated. The identification of atomic muonium by means of its ground state magnetic properties is described with reference to the Breit-Rabi diagram. This diagram is invaluable for interpreting or predicting MuSR observations, both in transverse and longitudinal magnetic fields, so its construction and properties are explained in some detail. The precession signals observed in transverse-field MuSR correspond to transitions allowed between the energy levels in this diagram; particular attention is paid to the spectra characteristic of the high and low field regimes. The different states of muonium observed in dielectric, semiconducting and metallic materials are introduced. The influence of the host medium on the spectral parameters, hyperfine interaction and linewidth, is considered both for atomic muonium and for muonium which is chemically bound in paramagnetic molecules, for which the Breit-Rabi diagram also applies. (orig.)

Safety factor profile dependence of turbulent structure formation in relevant to internal transport barrier relaxation

International Nuclear Information System (INIS)

Tokunaga, S.; Yagi, M.; Itoh, S.-I.; Itoh, K.

2009-01-01

Full text: It is widely understood that the improved confinement mode with transport barrier is necessary to achieve the self-ignition condition in ITER. The negative magnetic shear, mean ExB flow shear, and zonal flow are considered to play important roles for ITB formation. In our previous study, it is found that the non-linear interaction between the meso-scale modes produces non-local energy transfer to the off-resonant mode in the vicinity of q min surface and brings global relaxation of the temperature profile involving ITB collapse. Experimental studies indicate that a relationship exists between the ITB formation and safety factor q-profile, with a reversed magnetic shear (RS) configuration. Transitional ITB events occur on the low-order rational resonant surface. The ITB shape and location depend on the q-profile and q min position. These observations indicate that the q-profile might play an essential role in determining the turbulent structure. In this study, the effect of safety factor profile on the ion temperature gradient driven drift wave (ITG) turbulence is investigated using a global non-linear simulation code based on the gyro-fluid model. A heat source and toroidal momentum source are introduced. Dependence of safety factor profiles on ITB formation and its stability is examined to clarify the influence of the radial distribution of the rational surfaces and the q min value. It is found that the nonlinearly excited meso-scale mode in the vicinity of q min depends on the value of q min . A detailed analysis of the structure selection rule is in progress. (author)

What stage are low-income and middle-income countries (LMICs) at with patient safety curriculum implementation and what are the barriers to implementation? A two-stage cross-sectional study.

Science.gov (United States)

Ginsburg, Liane R; Dhingra-Kumar, Neelam; Donaldson, Liam J

2017-06-15

The improvement of safety in healthcare worldwide depends in part on the knowledge, skills and attitudes of staff providing care. Greater patient safety content in health professional education and training programmes has been advocated internationally. While WHO Patient Safety Curriculum Guides (for Medical Schools and Multi-Professional Curricula) have been widely disseminated in low-income and middle-income countries (LMICs) over the last several years, little is known about patient safety curriculum implementation beyond high-income countries. The present study examines patient safety curriculum implementation in LMICs. Two cross-sectional surveys were carried out. First, 88 technical officers in Ministries of Health and WHO country offices were surveyed to identify the pattern of patient safety curricula at country level. A second survey followed that gathered information from 71 people in a position to provide institution-level perspectives on patient safety curriculum implementation. The majority, 69% (30/44), of the countries were either considering whether to implement a patient safety curriculum or actively planning, rather than actually implementing, or embedding one. Most organisations recognised the need for patient safety education and training and felt a safety curriculum was compatible with the values of their organisation; however, important faculty-level barriers to patient safety curriculum implementation were identified. Key structural markers, such as dedicated financial resources and relevant assessment tools to evaluate trainees' patient safety knowledge and skills, were in place in fewer than half of organisations studied. Greater attention to patient safety curriculum implementation is needed. The barriers to patient safety curriculum implementation we identified in LMICs are not unique to these regions. We propose a framework to act as a global standard for patient safety curriculum implementation. Educating leaders through the system in

Impulse-Momentum Diagrams

Science.gov (United States)

Rosengrant, David

2011-01-01

Multiple representations are a valuable tool to help students learn and understand physics concepts. Furthermore, representations help students learn how to think and act like real scientists. These representations include: pictures, free-body diagrams, energy bar charts, electrical circuits, and, more recently, computer simulations and…

How design guides learning from matrix diagrams

NARCIS (Netherlands)

van der Meij, Jan; Amelsvoort, Marije; Anjewierden, Anjo

2017-01-01

Compared to text, diagrams are superior in their ability to structure and summarize information and to show relations between concepts and ideas. Perceptual cues, like arrows, are expected to improve the retention of diagrams by guiding the learner towards important elements or showing a preferred

Diagram of state of stiff amphiphilic macromolecules

NARCIS (Netherlands)

Markov, Vladimir A.; Vasilevskaya, Valentina V.; Khalatur, Pavel G.; ten Brinke, Gerrit; Khokhlov, Alexei R.

2007-01-01

We studied coil-globule transitions in stiff-chain amphiphilic macromolecules via computer modeling and constructed phase diagrams for such molecules in terms of solvent quality and persistence length. We showed that the shape of the phase diagram essentially depends on the macromolecule degree of

A Formal Verification Method of Function Block Diagram

International Nuclear Information System (INIS)

Koh, Kwang Yong; Seong, Poong Hyun; Jee, Eun Kyoung; Jeon, Seung Jae; Park, Gee Yong; Kwon, Kee Choon

2007-01-01

Programmable Logic Controller (PLC), an industrial computer specialized for real-time applications, is widely used in diverse control systems in chemical processing plants, nuclear power plants or traffic control systems. As a PLC is often used to implement safety, critical embedded software, rigorous safety demonstration of PLC code is necessary. Function block diagram (FBD) is a standard application programming language for the PLC and currently being used in the development of a fully-digitalized reactor protection system (RPS), which is called the IDiPS, under the KNICS project. Therefore, verification issue of FBD programs is a pressing problem, and hence is of great importance. In this paper, we propose a formal verification method of FBD programs; we defined FBD programs formally in compliance with IEC 61131-3, and then translate the programs into Verilog model, and finally the model is verified using a model checker SMV. To demonstrate the feasibility and effective of this approach, we applied it to IDiPS which currently being developed under KNICS project. The remainder of this paper is organized as follows. Section 2 briefly describes Verilog and Cadence SMV. In Section 3, we introduce FBD2V which is a tool implemented to support the proposed FBD verification framework. A summary and conclusion are provided in Section 4

Atomic energy levels and Grotrian diagrams

CERN Document Server

Bashkin, Stanley

1975-01-01

Atomic Energy Levels and Grotrian Diagrams, Volume I: Hydrogen I - Phosphorus XV presents diagrams of various elements that show their energy level and electronic transitions. The book covers the first 15 elements according to their atomic number. The text will be of great use to researchers and practitioners of fields such as astrophysics that requires pictorial representation of the energy levels and electronic transitions of elements.

Updating the Nomographical Diagrams for Dimensioning the Beams

OpenAIRE

Pop Maria T.

2015-01-01

In order to reduce the time period needed for structures design it is strongly recommended to use nomographical diagrams. The base for formation and updating the nomographical diagrams, stands on the charts presented by different technical publications. The updated charts use the same algorithm and calculation elements as the former diagrams in accordance to the latest prescriptions and European standards. The result consists in a chart, having the same properties, similar with the nomogragra...

Nuclear safety

International Nuclear Information System (INIS)

Tarride, Bruno

2015-10-01

The author proposes an overview of methods and concepts used in the nuclear industry, at the design level as well as at the exploitation level, to ensure an acceptable safety level, notably in the case of nuclear reactors. He first addresses the general objectives of nuclear safety and the notion of acceptable risk: definition and organisation of nuclear safety (relationships between safety authorities and operators), notion of acceptable risk, deterministic safety approach and main safety principles (safety functions and confinement barriers, concept of defence in depth). Then, the author addresses the safety approach at the design level: studies of operational situations, studies of internal and external aggressions, safety report, design principles for important-for-safety systems (failure criterion, redundancy, failure prevention, safety classification). The next part addresses safety during exploitation and general exploitation rules: definition of the operation domain and of its limits, periodic controls and tests, management in case of incidents, accidents or aggressions

Statistical analysis of internal transport barriers in JET

Energy Technology Data Exchange (ETDEWEB)

Maget, P [Association Euratom-CEA, Cadarache, F-13108 St Paul-lez-Durance (France); Esposito, B [Associazione Euratom-ENEA sulla Fusione, C.R. Frascati, Frascati (Italy); Joffrin, E [Association Euratom-CEA, Cadarache, F-13108 St Paul-lez-Durance (France); Hawkes, N [Euratom-UKAEA Fusion Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Mazon, D [Association Euratom-CEA, Cadarache, F-13108 St Paul-lez-Durance (France); Baranov, Y [Euratom-UKAEA Fusion Association, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Fourment, C [Association Euratom-CEA, Cadarache, F-13108 St Paul-lez-Durance (France); Hoang, G T [Association Euratom-CEA, Cadarache, F-13108 St Paul-lez-Durance (France)

2003-08-01

The potential role of magnetic shear, rational safety factor surfaces and shearing rate on the confinement is investigated on the basis of a database analysis of JET internal transport barriers (ITBs). The ITB is quantified using the JET ITB criterion (Tresset G et al 2002 Nucl. Fusion 42 520). The relation between the shearing rate and the magnetic shear, already established for positive magnetic shear barrier (Tala T J J et al 2001 Plasma Phys. Control. Fusion 43 507), is investigated at low and negative magnetic shear, where the threshold in shearing rate is found to be lower than for positive magnetic shear barriers. Defining the ITB from the departure from profile stiffness is found to be consistent with the database results, and the critical gradient length is found to be minimum at low magnetic shear. Finally, ITBs are found to be localized in the vicinity of integer safety factor surfaces in positive magnetic shear plasmas, whereas no correlation is found with integer values when the barrier is localized in negative magnetic shear regions.

Influence diagrams and decision trees for severe accident management

Energy Technology Data Exchange (ETDEWEB)

Goetz, W.W.J.

1996-09-01

A review of relevant methodologies based on Influence Diagrams (IDs), Decision Trees (DTs), and Containment Event Trees (CETs) was conducted to assess the practicality of these methods for the selection of effective strategies for Severe Accident Management (SAM). The review included an evaluation of some software packages for these methods. The emphasis was on possible pitfalls of using IDs and on practical aspects, the latter by performance of a case study that was based on an existing Level 2 Probabilistic Safety Assessment (PSA). The study showed that the use of a combined ID/DT model has advantages over CET models, in particular when conservatisms in the Level 2 PSA have been identified and replaced by fair assessments of the uncertainties involved. It is recommended to use ID/DT models complementary to CET models. (orig.).

Influence diagrams and decision trees for severe accident management

International Nuclear Information System (INIS)

Goetz, W.W.J.; Seebregts, A.J.; Bedford, T.J.

1996-08-01

A review of relevent methodologies based on Influence Diagrams (IDs), Decision Trees (DTs), and Containment Event Trees (CETs) was conducted to assess the practicality of these methods for the selection of effective strategies for Severe Accident Management (SAM). The review included an evaluation of some software packages for these methods. The emphasis was on possible pitfalls of using IDs and on practical aspects, the latter by performance of a case study that was based on an existing Level 2 Probabilistic Safety Assessment (PSA). The study showed that the use of a combined ID/DT model has advantages over CET models, in particular when conservatisms in the Level 2 PSA have been identified and replaced by fair assessments of the uncertainties involved. It is recommended to use ID/DT models as complementary to CET models. (orig.)

Influence diagrams and decision trees for severe accident management

International Nuclear Information System (INIS)

Goetz, W.W.J.

1996-09-01

A review of relevant methodologies based on Influence Diagrams (IDs), Decision Trees (DTs), and Containment Event Trees (CETs) was conducted to assess the practicality of these methods for the selection of effective strategies for Severe Accident Management (SAM). The review included an evaluation of some software packages for these methods. The emphasis was on possible pitfalls of using IDs and on practical aspects, the latter by performance of a case study that was based on an existing Level 2 Probabilistic Safety Assessment (PSA). The study showed that the use of a combined ID/DT model has advantages over CET models, in particular when conservatisms in the Level 2 PSA have been identified and replaced by fair assessments of the uncertainties involved. It is recommended to use ID/DT models complementary to CET models. (orig.)

Dynamics of safety performance and culture: a group model building approach.

Science.gov (United States)

Goh, Yang Miang; Love, Peter E D; Stagbouer, Greg; Annesley, Chris

2012-09-01

The management of occupational health and safety (OHS) including safety culture interventions is comprised of complex problems that are often hard to scope and define. Due to the dynamic nature and complexity of OHS management, the concept of system dynamics (SD) is used to analyze accident prevention. In this paper, a system dynamics group model building (GMB) approach is used to create a causal loop diagram of the underlying factors influencing the OHS performance of a major drilling and mining contractor in Australia. While the organization has invested considerable resources into OHS their disabling injury frequency rate (DIFR) has not been decreasing. With this in mind, rich individualistic knowledge about the dynamics influencing the DIFR was acquired from experienced employees with operations, health and safety and training background using a GMB workshop. Findings derived from the workshop were used to develop a series of causal loop diagrams that includes a wide range of dynamics that can assist in better understanding the causal influences OHS performance. The causal loop diagram provides a tool for organizations to hypothesize the dynamics influencing effectiveness of OHS management, particularly the impact on DIFR. In addition the paper demonstrates that the SD GMB approach has significant potential in understanding and improving OHS management. Copyright © 2011 Elsevier Ltd. All rights reserved.

Spin wave Feynman diagram vertex computation package

Science.gov (United States)

Price, Alexander; Javernick, Philip; Datta, Trinanjan

Spin wave theory is a well-established theoretical technique that can correctly predict the physical behavior of ordered magnetic states. However, computing the effects of an interacting spin wave theory incorporating magnons involve a laborious by hand derivation of Feynman diagram vertices. The process is tedious and time consuming. Hence, to improve productivity and have another means to check the analytical calculations, we have devised a Feynman Diagram Vertex Computation package. In this talk, we will describe our research group's effort to implement a Mathematica based symbolic Feynman diagram vertex computation package that computes spin wave vertices. Utilizing the non-commutative algebra package NCAlgebra as an add-on to Mathematica, symbolic expressions for the Feynman diagram vertices of a Heisenberg quantum antiferromagnet are obtained. Our existing code reproduces the well-known expressions of a nearest neighbor square lattice Heisenberg model. We also discuss the case of a triangular lattice Heisenberg model where non collinear terms contribute to the vertex interactions.

The classification of diagrams in perturbation theory

International Nuclear Information System (INIS)

Phillips, D.R.; Afnan, I.R.

1995-01-01

The derivation of scattering equations connecting the amplitudes obtained from diagrammatic expansions is of interest in many branches of physics. One method for deriving such equations is the classification-of-diagrams technique of Taylor. However, as we shall explain in this paper, there are certain points of Taylor's method which require clarification. First, it is not clear whether Taylor's original method is equivlant to the simpler classification-of-diagrams scheme used by Thomas, Rinat, Afnan, and Blankleider (TRAB). Second, when the Taylor method is applied to certain problems in a time-dependent perturbation theory it leads to the over-counting of some diagrams. This paper first restates Taylor's method, in the process uncovering reasons why certain diagrams might be double-counted in the Taylor method. In then explores how far Taylor's method is equivalent to the simpler TRAB method. Finally, it examines precisely why the double-counting occurs in Taylor's method and derives corrections which compensate for this double-counting. copyright 1995 Academic Press, Inc

Influence diagram in evaluating the subjective judgment

International Nuclear Information System (INIS)

Hong, Y.

1997-01-01

The author developed the idea of the subjective influence diagrams to evaluate subjective judgment. The subjective judgment of a stake holder is a primary decision making proposition. It involves a basic decision process an the individual attitude of the stake holder for his decision purpose. The subjective judgment dominates the some final decisions. A complex decision process may include the subjective judgment. An influence diagram framework is a simplest tool for analyzing subjective judgment process. In the framework, the characters of influence diagrams generate the describing the analyzing, and the evaluating of the subjective judgment. The relationship between the information and the decision, such as independent character between them, is the main issue. Then utility function is the calculating tool to evaluation, the stake holder can make optimal decision. Through the analysis about the decision process and relationship, the building process of the influence diagram identically describes the subjective judgment. Some examples are given to explain the property of subjective judgment and the analysis process

Lattice and Phase Diagram in QCD

International Nuclear Information System (INIS)

Lombardo, Maria Paola

2008-01-01

Model calculations have produced a number of very interesting expectations for the QCD Phase Diagram, and the task of a lattice calculations is to put these studies on a quantitative grounds. I will give an overview of the current status of the lattice analysis of the QCD phase diagram, from the quantitative results of mature calculations at zero and small baryochemical potential, to the exploratory studies of the colder, denser phase.

Ferroelectric Phase Diagram of PVDF:PMMA

OpenAIRE

Li, Mengyuan; Stingelin, Natalie; Michels, Jasper J.; Spijkman, Mark-Jan; Asadi, Kamal; Feldman, Kirill; Blom, Paul W. M.; de Leeuw, Dago M.

2012-01-01

We have investigated the ferroelectric phase diagram of poly(vinylidene fluoride) (PVDF) and poly(methyl methacrylate) (PMMA). The binary nonequilibrium temperature composition diagram was determined and melting of alpha- and beta-phase PVDF was identified. Ferroelectric beta-PVDF:PMMA blend films were made by melting, ice quenching, and subsequent annealing above the glass transition temperature of PMMA, close to the melting temperature of PVDF. Addition of PMMA suppresses the crystallizatio...

Gluing Ladder Feynman Diagrams into Fishnets

International Nuclear Information System (INIS)

Basso, Benjamin; Dixon, Lance J.; Stanford University, CA; University of California, Santa Barbara, CA

2017-01-01

We use integrability at weak coupling to compute fishnet diagrams for four-point correlation functions in planar Φ "4 theory. Our results are always multilinear combinations of ladder integrals, which are in turn built out of classical polylogarithms. The Steinmann relations provide a powerful constraint on such linear combinations, which leads to a natural conjecture for any fishnet diagram as the determinant of a matrix of ladder integrals.

Barriers and Facilitators to Online Portal Use Among Patients and Caregivers in a Safety Net Health Care System: A Qualitative Study.

Science.gov (United States)

Tieu, Lina; Sarkar, Urmimala; Schillinger, Dean; Ralston, James D; Ratanawongsa, Neda; Pasick, Rena; Lyles, Courtney R

2015-12-03

Patient portals have the potential to support self-management for chronic diseases and improve health outcomes. With the rapid rise in adoption of patient portals spurred by meaningful use incentives among safety net health systems (a health system or hospital providing a significant level of care to low-income, uninsured, and vulnerable populations), it is important to understand the readiness and willingness of patients and caregivers in safety net settings to access their personal health records online. To explore patient and caregiver perspectives on online patient portal use before its implementation at San Francisco General Hospital, a safety net hospital. We conducted 16 in-depth interviews with chronic disease patients and caregivers who expressed interest in using the Internet to manage their health. Discussions focused on health care experiences, technology use, and interest in using an online portal to manage health tasks. We used open coding to categorize all the barriers and facilitators to portal use, followed by a second round of coding that compared the categories to previously published findings. In secondary analyses, we also examined specific barriers among 2 subgroups: those with limited health literacy and caregivers. We interviewed 11 patients and 5 caregivers. Patients were predominantly male (82%, 9/11) and African American (45%, 5/11). All patients had been diagnosed with diabetes and the majority had limited health literacy (73%, 8/11). The majority of caregivers were female (80%, 4/5), African American (60%, 3/5), caregivers of individuals with diabetes (60%, 3/5), and had adequate health literacy (60%, 3/5). A total of 88% (14/16) of participants reported interest in using the portal after viewing a prototype. Major perceived barriers included security concerns, lack of technical skills/interest, and preference for in-person communication. Facilitators to portal use included convenience, health monitoring, and improvements in patient

A Critical Appraisal of the "Day" Diagram

Science.gov (United States)

Roberts, Andrew P.; Tauxe, Lisa; Heslop, David; Zhao, Xiang; Jiang, Zhaoxia

2018-04-01

The "Day" diagram (Day et al., 1977, https://doi.org/10.1016/0031-9201(77)90108-X) is used widely to make inferences about the domain state of magnetic mineral assemblages. Based on theoretical and empirical arguments, the Day diagram is demarcated into stable "single domain" (SD), "pseudo single domain" ("PSD"), and "multidomain" (MD) zones. It is straightforward to make the necessary measurements for a sample and to plot results within the "domain state" framework based on the boundaries defined by Day et al. (1977, https://doi.org/10.1016/0031-9201(77)90108-X). We discuss 10 issues that limit Day diagram interpretation, including (1) magnetic mineralogy, (2) the associated magnetocrystalline anisotropy type, (3) mineral stoichiometry, (4) stress state, (5) surface oxidation, (6) magnetostatic interactions, (7) particle shape, (8) thermal relaxation, (9) magnetic particle mixtures, and (10) definitional/measurement issues. In most studies, these variables are unknowns and cannot be controlled for, so that hysteresis parameters for single bulk samples are nonunique and any data point in a Day diagram could result from infinite combinations of relevant variables. From this critical appraisal, we argue that the Day diagram is fundamentally ambiguous for domain state diagnosis. Widespread use of the Day diagram has also contributed significantly to prevalent but questionable views, including underrecognition of the importance of stable SD particles in the geological record and reinforcement of the unhelpful PSD concept and of its geological importance. Adoption of approaches that enable correct domain state diagnosis should be an urgent priority for component-specific understanding of magnetic mineral assemblages and for quantitative rock magnetic interpretation.

Pitfalls and feedback when constructing topological pressure-temperature phase diagrams

Science.gov (United States)

Ceolin, R.; Toscani, S.; Rietveld, Ivo B.; Barrio, M.; Tamarit, J. Ll.

2017-04-01

The stability hierarchy between different phases of a chemical compound can be accurately reproduced in a topological phase diagram. This type of phase diagrams may appear to be the result of simple extrapolations, however, experimental complications quickly increase in the case of crystalline trimorphism (and higher order polymorphism). To ensure the accurate positioning of stable phase domains, a topological phase diagram needs to be consistent. This paper gives an example of how thermodynamic feedback can be used in the topological construction of phase diagrams to ensure overall consistency in a phase diagram based on the case of piracetam crystalline trimorphism.

Phase diagram of spiking neural networks.

Science.gov (United States)

Seyed-Allaei, Hamed

2015-01-01

In computer simulations of spiking neural networks, often it is assumed that every two neurons of the network are connected by a probability of 2%, 20% of neurons are inhibitory and 80% are excitatory. These common values are based on experiments, observations, and trials and errors, but here, I take a different perspective, inspired by evolution, I systematically simulate many networks, each with a different set of parameters, and then I try to figure out what makes the common values desirable. I stimulate networks with pulses and then measure their: dynamic range, dominant frequency of population activities, total duration of activities, maximum rate of population and the occurrence time of maximum rate. The results are organized in phase diagram. This phase diagram gives an insight into the space of parameters - excitatory to inhibitory ratio, sparseness of connections and synaptic weights. This phase diagram can be used to decide the parameters of a model. The phase diagrams show that networks which are configured according to the common values, have a good dynamic range in response to an impulse and their dynamic range is robust in respect to synaptic weights, and for some synaptic weights they oscillates in α or β frequencies, independent of external stimuli.

New safety concept for geological disposal in Japan - -16339

International Nuclear Information System (INIS)

Kitayama, Kazumi

2009-01-01

This paper describes a new safety concept for the Japanese geological disposal program, which is a development of the conventional multi-barrier system concept. The Japanese government established the 'Nuclear Waste Management Organization of Japan' (NUMO) as an implementation body in 2000 based on the 'Final disposal act' following the publication of the 'H-12 Report', which confirmed the scientific and engineering feasibility of HLW geological disposal in Japan. Since then, NUMO has undertaken further technical developments aimed at achieving safe and efficient implementation of final disposal. The safety concept developed in the 'H-12 Report' provides sufficient safety on the basis of site-generic considerations. However, it is considered to be over-conservative and therefore does not represent the most probable performance of the engineered or natural barriers. Recently, concrete measures have been proposed requiring the safety case to be presented in terms of a realistic assessment of the most probable performance. This approach takes into account the safety functions of both engineered and natural barriers as well as the long-term static geochemical equilibrium. In particular, the evolution of the safety performance of engineered and natural barriers can be efficiently augmented by the realistic long-term geochemical equilibrium. (author)

Transport Barriers in Bootstrap Driven Tokamaks

Science.gov (United States)

Staebler, Gary

2017-10-01

Maximizing the bootstrap current in a tokamak, so that it drives a high fraction of the total current, reduces the external power required to drive current by other means. Improved energy confinement, relative to empirical scaling laws, enables a reactor to more fully take advantage of the bootstrap driven tokamak. Experiments have demonstrated improved energy confinement due to the spontaneous formation of an internal transport barrier in high bootstrap fraction discharges. Gyrokinetic analysis, and quasilinear predictive modeling, demonstrates that the observed transport barrier is due to the suppression of turbulence primarily due to the large Shafranov shift. ExB velocity shear does not play a significant role in the transport barrier due to the high safety factor. It will be shown, that the Shafranov shift can produce a bifurcation to improved confinement in regions of positive magnetic shear or a continuous reduction in transport for weak or negative magnetic shear. Operation at high safety factor lowers the pressure gradient threshold for the Shafranov shift driven barrier formation. The ion energy transport is reduced to neoclassical and electron energy and particle transport is reduced, but still turbulent, within the barrier. Deeper into the plasma, very large levels of electron transport are observed. The observed electron temperature profile is shown to be close to the threshold for the electron temperature gradient (ETG) mode. A large ETG driven energy transport is qualitatively consistent with recent multi-scale gyrokinetic simulations showing that reducing the ion scale turbulence can lead to large increase in the electron scale transport. A new saturation model for the quasilinear TGLF transport code, that fits these multi-scale gyrokinetic simulations, can match the data if the impact of zonal flow mixing on the ETG modes is reduced at high safety factor. This work was supported by the U.S. Department of Energy under DE-FG02-95ER54309 and DE-FC02

Repair of Partly Misspecified Causal Diagrams.

Science.gov (United States)

Oates, Chris J; Kasza, Jessica; Simpson, Julie A; Forbes, Andrew B

2017-07-01

Errors in causal diagrams elicited from experts can lead to the omission of important confounding variables from adjustment sets and render causal inferences invalid. In this report, a novel method is presented that repairs a misspecified causal diagram through the addition of edges. These edges are determined using a data-driven approach designed to provide improved statistical efficiency relative to de novo structure learning methods. Our main assumption is that the expert is "directionally informed," meaning that "false" edges provided by the expert would not create cycles if added to the "true" causal diagram. The overall procedure is cast as a preprocessing technique that is agnostic to subsequent causal inferences. Results based on simulated data and data derived from an observational cohort illustrate the potential for data-assisted elicitation in epidemiologic applications. See video abstract at, http://links.lww.com/EDE/B208.

Simple method for evaluating Goldstone diagrams in an angular momentum coupled representation

International Nuclear Information System (INIS)

Kuo, T.T.S.; Shurpin, J.; Tam, K.C.; Osnes, E.; Ellis, P.J.

1981-01-01

A simple and convenient method is derived for evaluating linked Goldstone diagrams in an angular momentum coupled representation. Our method is general, and can be used to evaluate any effective interaction and/or effective operator diagrams for both closed-shell nuclei (vacuum to vacuum linked diagrams) and open-shell nuclei (valence linked diagrams). The techniques of decomposing diagrams into ladder diagrams, cutting open internal lines and cutting off one-body insertions are introduced. These enable us to determine angular momentum factors associated with diagrams in the coupled representation directly, without the need for carrying out complicated angular momentum algebra. A summary of diagram rules is given

Diagrams for symmetric product orbifolds

International Nuclear Information System (INIS)

Pakman, Ari; Rastelli, Leonardo; Razamat, Shlomo S.

2009-01-01

We develop a diagrammatic language for symmetric product orbifolds of two-dimensional conformal field theories. Correlation functions of twist operators are written as sums of diagrams: each diagram corresponds to a branched covering map from a surface where the fields are single-valued to the base sphere where twist operators are inserted. This diagrammatic language facilitates the study of the large N limit and makes more transparent the analogy between symmetric product orbifolds and free non-abelian gauge theories. We give a general algorithm to calculate the leading large N contribution to four-point correlators of twist fields.

How Design Guides Learning from Matrix Diagrams

Science.gov (United States)

van der Meij, Jan; van Amelsvoort, Marije; Anjewierden, Anjo

2017-01-01

Compared to text, diagrams are superior in their ability to structure and summarize information and to show relations between concepts and ideas. Perceptual cues, like arrows, are expected to improve the retention of diagrams by guiding the learner towards important elements or showing a preferred reading sequence. In our experiment, we analyzed…

Interrelations between random walks on diagrams (graphs) with and without cycles.

Science.gov (United States)

Hill, T L

1988-05-01

Three topics are discussed. A discrete-state, continuous-time random walk with one or more absorption states can be studied by a presumably new method: some mean properties, including the mean time to absorption, can be found from a modified diagram (graph) in which each absorption state is replaced by a one-way cycle back to the starting state. The second problem is a random walk on a diagram (graph) with cycles. The walk terminates on completion of the first cycle. This walk can be replaced by an equivalent walk on a modified diagram with absorption. This absorption diagram can in turn be replaced by another modified diagram with one-way cycles back to the starting state, just as in the first problem. The third problem, important in biophysics, relates to a long-time continuous walk on a diagram with cycles. This diagram can be transformed (in two steps) to a modified, more-detailed, diagram with one-way cycles only. Thus, the one-way cycle fluxes of the original diagram can be found from the state probabilities of the modified diagram. These probabilities can themselves be obtained by simple matrix inversion (the probabilities are determined by linear algebraic steady-state equations). Thus, a simple method is now available to find one-way cycle fluxes exactly (previously Monte Carlo simulation was required to find these fluxes, with attendant fluctuations, for diagrams of any complexity). An incidental benefit of the above procedure is that it provides a simple proof of the one-way cycle flux relation Jn +/- = IIn +/- sigma n/sigma, where n is any cycle of the original diagram.

Changing An Electrical Safety Culture - The Importance of Understanding Why.

Energy Technology Data Exchange (ETDEWEB)

Waters, Richard Thomas [Idaho National Laboratory

2015-12-01

Abstract – Electrical workers, regardless of experience, are faced with a major barrier when first introduced to NFPA 70E, “The Standard for Electrical Safety in the Workplace,” and an erroneous electrical safety culture pre-exists. This paper describes, from the author’s point of view, the barrier that he and other electrical workers have experienced and his insight into overcoming the barrier. The author in conclusion will present a series of techniques that can be used to assist other electrical workers in overcoming the barrier.

Asymptotic Safety Guaranteed in Supersymmetry

Science.gov (United States)

Bond, Andrew D.; Litim, Daniel F.

2017-11-01

We explain how asymptotic safety arises in four-dimensional supersymmetric gauge theories. We provide asymptotically safe supersymmetric gauge theories together with their superconformal fixed points, R charges, phase diagrams, and UV-IR connecting trajectories. Strict perturbative control is achieved in a Veneziano limit. Consistency with unitarity and the a theorem is established. We find that supersymmetry enhances the predictivity of asymptotically safe theories.

Peircean diagrams of time

DEFF Research Database (Denmark)

Øhrstrøm, Peter

2011-01-01

Some very good arguments can be given in favor of the Augustinean wisdom, according to which it is impossible to provide a satisfactory definition of the concept of time. However, even in the absence of a proper definition, it is possible to deal with conceptual problems regarding time. It can...... be done in terms of analogies and metaphors. In particular, it is attractive to make use of Peirce's diagrams by means of which various kinds of conceptual experimentation can be carried out. This paper investigates how Peircean diagrams can be used within the study of time. In particular, we discuss 1......) the topological properties of time, 2) the implicative structure in tense logic, 3) the notions of open future and branching time models, and finally 4) tenselogical alternatives to branching time models....

Extended sequence diagram for human system interaction

International Nuclear Information System (INIS)

Hwang, Jong Rok; Choi, Sun Woo; Ko, Hee Ran; Kim, Jong Hyun

2012-01-01

Unified Modeling Language (UML) is a modeling language in the field of object oriented software engineering. The sequence diagram is a kind of interaction diagram that shows how processes operate with one another and in what order. It is a construct of a message sequence chart. It depicts the objects and classes involved in the scenario and the sequence of messages exchanged between the objects needed to carry out the functionality of the scenario. This paper proposes the Extended Sequence Diagram (ESD), which is capable of depicting human system interaction for nuclear power plants, as well as cognitive process of operators analysis. In the conventional sequence diagram, there is a limit to only identify the activities of human and systems interactions. The ESD is extended to describe operators' cognitive process in more detail. The ESD is expected to be used as a task analysis method for describing human system interaction. The ESD can also present key steps causing abnormal operations or failures and diverse human errors based on cognitive condition

Simulation modeling on the growth of firm's safety management capability

Institute of Scientific and Technical Information of China (English)

LIU Tie-zhong; LI Zhi-xiang

2008-01-01

Aiming to the deficiency of safety management measure, established simulation model about firm's safety management capability(FSMC) based on organizational learning theory. The system dynamics(SD) method was used, in which level and rate system, variable equation and system structure flow diagram was concluded. Simulation model was verified from two aspects: first, model's sensitivity to variable was tested from the gross of safety investment and the proportion of safety investment; second, variables dependency was checked up from the correlative variable of FSMC and organizational learning. The feasibility of simulation model is verified though these processes.

Methodology of strength calculation under alternating stresses using the diagram of limiting amplitudes

Science.gov (United States)

Konovodov, V. V.; Valentov, A. V.; Kukhar, I. S.; Retyunskiy, O. Yu; Baraksanov, A. S.

2016-08-01

The work proposes the algorithm to calculate strength under alternating stresses using the developed methodology of building the diagram of limiting stresses. The overall safety factor is defined by the suggested formula. Strength calculations of components working under alternating stresses in the great majority of cases are conducted as the checking ones. It is primarily explained by the fact that the overall fatigue strength reduction factor (Kσg or Kτg) can only be chosen approximately during the component design as the engineer at this stage of work has just the approximate idea on the component size and shape.

An Introduction to Binary Decision Diagrams

DEFF Research Database (Denmark)

Andersen, Henrik Reif

1996-01-01

This note is a short introduction to Binary Decision Diagrams (BDDs). It provides some background knowledge and describes the core algorithms. It is used in the course "C4340 Advanced Algorithms" at the Technical University of Denmark, autumn 1996.......This note is a short introduction to Binary Decision Diagrams (BDDs). It provides some background knowledge and describes the core algorithms. It is used in the course "C4340 Advanced Algorithms" at the Technical University of Denmark, autumn 1996....

The Butterfly diagram leopard skin pattern

Science.gov (United States)

Ternullo, Maurizio

2011-08-01

A time-latitude diagram where spotgroups are given proportional relevance to their area is presented. The diagram reveals that the spotted area distribution is higly dishomogeneous, most of it being concentrated in few, small portions (``knots'') of the Butterfly Diagram; because of this structure, the BD may be properly described as a cluster of knots. The description, assuming that spots scatter around the ``spot mean latitude'' steadily drifting equatorward, is challenged. Indeed, spots cluster around at as many latitudes as knots; a knot may appear at either lower or higher latitudes than previous ones, in a seemingly random way; accordingly, the spot mean latitude abruptly drifts equatorward or even poleward at any knot activation, in spite of any smoothing procedure. Preliminary analyses suggest that the activity splits, in any hemisphere, into two or more distinct ``activity waves'', drifting equatorward at a rate higher than the spot zone as a whole.

Construction of UML class diagram with Model-Driven Development

Directory of Open Access Journals (Sweden)

Tomasz Górski

2016-03-01

Full Text Available Model transformations play a key role in software development projects based on Model--Driven Development (MDD principles. Transformations allow for automation of repetitive and well-defined steps, thus shortening design time and reducing a number of errors. In the object-oriented approach, the key elements are use cases. They are described, modelled and later designed until executable application code is obtained. The aim of the paper is to present transformation of a model-to-model type, Communication-2-Class, which automates construction of Unified Modelling Language (UML class diagram in the context of the analysis/design model. An UML class diagram is created based on UML communication diagram within use case realization. As a result, a class diagram shows all of the classes involved in the use case realization and the relationships among them. The plug-in which implements Communication-2-Class transformation was implemented in the IBM Rational Software Architect. The article presents the tests results of developed plug-in, which realizes Communication-2-Class transformation, showing capabilities of shortening use case realization’s design time.[b]Keywords[/b]: Model-Driven Development, transformations, Unified Modelling Language, analysis/design model, UML class diagram, UML communication diagram

Barriers and facilitators for promotoras' success in delivering pesticide safety education to Latino farmworker families: La Familia Sana.

Science.gov (United States)

Trejo, Grisel; Arcury, Thomas A; Grzywacz, Joseph G; Tapia, Janeth; Quandt, Sara A

2013-01-01

Despite widespread use of lay health advisor (LHA) programs, factors related to success of LHAs remain largely unexamined. This study describes experiences and personal transformations of LHAs (promotoras de salud) in a pesticide safety education program targeting farmworker families in North Carolina, using postintervention in-depth interviews conducted with 17 LHAs. LHAs identified assets and barriers that affected their success. LHAs also described increases in self-efficacy and empowerment resulting in perceived improvements in ability to teach and impact their community. Such positive changes are essential benefits to the LHAs. Evaluations that address these topics are needed to better understand continuity and attrition in LHA programs.

Efficient computation of clipped Voronoi diagram for mesh generation

KAUST Repository

Yan, Dongming

2013-04-01

The Voronoi diagram is a fundamental geometric structure widely used in various fields, especially in computer graphics and geometry computing. For a set of points in a compact domain (i.e. a bounded and closed 2D region or a 3D volume), some Voronoi cells of their Voronoi diagram are infinite or partially outside of the domain, but in practice only the parts of the cells inside the domain are needed, as when computing the centroidal Voronoi tessellation. Such a Voronoi diagram confined to a compact domain is called a clipped Voronoi diagram. We present an efficient algorithm to compute the clipped Voronoi diagram for a set of sites with respect to a compact 2D region or a 3D volume. We also apply the proposed method to optimal mesh generation based on the centroidal Voronoi tessellation. Crown Copyright © 2011 Published by Elsevier Ltd. All rights reserved.

Efficient computation of clipped Voronoi diagram for mesh generation

KAUST Repository

Yan, Dongming; Wang, Wen Ping; Lé vy, Bruno L.; Liu, Yang

2013-01-01

The Voronoi diagram is a fundamental geometric structure widely used in various fields, especially in computer graphics and geometry computing. For a set of points in a compact domain (i.e. a bounded and closed 2D region or a 3D volume), some Voronoi cells of their Voronoi diagram are infinite or partially outside of the domain, but in practice only the parts of the cells inside the domain are needed, as when computing the centroidal Voronoi tessellation. Such a Voronoi diagram confined to a compact domain is called a clipped Voronoi diagram. We present an efficient algorithm to compute the clipped Voronoi diagram for a set of sites with respect to a compact 2D region or a 3D volume. We also apply the proposed method to optimal mesh generation based on the centroidal Voronoi tessellation. Crown Copyright © 2011 Published by Elsevier Ltd. All rights reserved.

A Community Based Systems Diagram of Obesity Causes.

Directory of Open Access Journals (Sweden)

Steven Allender

Full Text Available Application of system thinking to the development, implementation and evaluation of childhood obesity prevention efforts represents the cutting edge of community-based prevention. We report on an approach to developing a system oriented community perspective on the causes of obesity.Group model building sessions were conducted in a rural Australian community to address increasing childhood obesity. Stakeholders (n = 12 built a community model that progressed from connection circles to causal loop diagrams using scripts from the system dynamics literature. Participants began this work in identifying change over time in causes and effects of childhood obesity within their community. The initial causal loop diagram was then reviewed and elaborated by 50 community leaders over a full day session.The process created a causal loop diagram representing community perceptions of determinants and causes of obesity. The causal loop diagram can be broken down into four separate domains; social influences; fast food and junk food; participation in sport; and general physical activity.This causal loop diagram can provide the basis for community led planning of a prevention response that engages with multiple levels of existing settings and systems.

An approach for continuous cooling transformation (CCT) diagrams of aluminium alloys

International Nuclear Information System (INIS)

Herding, T.; Kessler, O.; Hoffmann, F.; Mayr, P.

2002-01-01

Two different kinds of time temperature transformation (TTT) diagrams are known. The first one are isothermal transformation (IT) diagrams and the second one continuous cooling transformation (CCT) diagrams. These diagrams are important for the correct heat treatment of aluminium alloys, because they provide information about the required quenching rate, which is necessary to obtain a supersaturated solid solution during age hardening. Furthermore, it is possible to determine the lowest quenching rate, which permits both a high strength and a small distortion of the component after age hardening. In the literature IT diagrams for different aluminium alloys are available. To determine these diagrams, a solution annealing followed by quenching to defined temperatures is necessary. At these temperatures the alloy is kept isothermally until a transformation has started. These diagrams are not directly portable on continuous cooling, because of the different cooling paths. (orig.)

Effects of Three Diagram Instruction Methods on Transfer of Diagram Comprehension Skills: The Critical Role of Inference While Learning

Science.gov (United States)

Cromley, Jennifer G.; Bergey, Bradley W.; Fitzhugh, Shannon; Newcombe, Nora; Wills, Theodore W.; Shipley, Thomas F.; Tanaka, Jacqueline C.

2013-01-01

Can students be taught to better comprehend the diagrams in their textbooks? Can such teaching transfer to uninstructed diagrams in the same domain or even in a new domain? What methods work best for these goals? Building on previous research showing positive results compared to control groups in both laboratory studies and short-term…

eulerAPE: drawing area-proportional 3-Venn diagrams using ellipses.

Science.gov (United States)

Micallef, Luana; Rodgers, Peter

2014-01-01

Venn diagrams with three curves are used extensively in various medical and scientific disciplines to visualize relationships between data sets and facilitate data analysis. The area of the regions formed by the overlapping curves is often directly proportional to the cardinality of the depicted set relation or any other related quantitative data. Drawing these diagrams manually is difficult and current automatic drawing methods do not always produce appropriate diagrams. Most methods depict the data sets as circles, as they perceptually pop out as complete distinct objects due to their smoothness and regularity. However, circles cannot draw accurate diagrams for most 3-set data and so the generated diagrams often have misleading region areas. Other methods use polygons to draw accurate diagrams. However, polygons are non-smooth and non-symmetric, so the curves are not easily distinguishable and the diagrams are difficult to comprehend. Ellipses are more flexible than circles and are similarly smooth, but none of the current automatic drawing methods use ellipses. We present eulerAPE as the first method and software that uses ellipses for automatically drawing accurate area-proportional Venn diagrams for 3-set data. We describe the drawing method adopted by eulerAPE and we discuss our evaluation of the effectiveness of eulerAPE and ellipses for drawing random 3-set data. We compare eulerAPE and various other methods that are currently available and we discuss differences between their generated diagrams in terms of accuracy and ease of understanding for real world data.

eulerAPE: drawing area-proportional 3-Venn diagrams using ellipses.

Directory of Open Access Journals (Sweden)

Luana Micallef

Full Text Available Venn diagrams with three curves are used extensively in various medical and scientific disciplines to visualize relationships between data sets and facilitate data analysis. The area of the regions formed by the overlapping curves is often directly proportional to the cardinality of the depicted set relation or any other related quantitative data. Drawing these diagrams manually is difficult and current automatic drawing methods do not always produce appropriate diagrams. Most methods depict the data sets as circles, as they perceptually pop out as complete distinct objects due to their smoothness and regularity. However, circles cannot draw accurate diagrams for most 3-set data and so the generated diagrams often have misleading region areas. Other methods use polygons to draw accurate diagrams. However, polygons are non-smooth and non-symmetric, so the curves are not easily distinguishable and the diagrams are difficult to comprehend. Ellipses are more flexible than circles and are similarly smooth, but none of the current automatic drawing methods use ellipses. We present eulerAPE as the first method and software that uses ellipses for automatically drawing accurate area-proportional Venn diagrams for 3-set data. We describe the drawing method adopted by eulerAPE and we discuss our evaluation of the effectiveness of eulerAPE and ellipses for drawing random 3-set data. We compare eulerAPE and various other methods that are currently available and we discuss differences between their generated diagrams in terms of accuracy and ease of understanding for real world data.

XLOOPS - a package calculating one- and two-loop diagrams

International Nuclear Information System (INIS)

Bruecher, L.

1997-01-01

A program package for calculating massive one- and two-loop diagrams is introduced. It consists of five parts: - a graphical user interface, - routines for generating diagrams from particle input, - procedures for calculating one-loop integrals both analytically and numerically, - routines for massive two-loop integrals, - programs for numerical integration of two-loop diagrams. Here the graphical user interface and the text interface to Maple are presented. (orig.)

Oak Ridge K-25 Site Technology Logic Diagram. Volume 2, Technology Logic Diagrams

Energy Technology Data Exchange (ETDEWEB)

Fellows, R.L. [ed.

1993-02-26

The Oak Ridge K-25 Technology Logic Diagram (TLD), a decision support tool for the K-25 Site, was developed to provide a planning document that relates envirorunental restoration and waste management problems at the Oak Ridge K-25 Site to potential technologies that can remediate these problems. The TLD technique identifies the research necessary to develop these technologies to a state that allows for technology transfer and application to waste management, remedial action, and decontamination and decommissioning activities. The TLD consists of four separate volumes-Vol. 1, Vol. 2, Vol. 3A, and Vol. 3B. Volume 1 provides introductory and overview information about the TLD. This volume, Volume 2, contains logic diagrams with an index. Volume 3 has been divided into two separate volumes to facilitate handling and use.

Grotrian diagrams of highly ionized iron Fe(VIII)-Fe(XXVI)

International Nuclear Information System (INIS)

Mori, Kazuo; Otsuka, Masamoto; Kato, Takako.

1977-08-01

Energy levels and Grotrian diagrams of Fe(VIII) to Fe(XXVI) are presented. This report summarized the data published recently up to 1976, and the wavelength tables compiled were converted to the Grotrian diagrams. The diagrams showing transition from one energy level to another are called Grotrian diagrams. Typical examples of the diagrams are found in the book by Bashkin et al. In the present diagrams, all lines are drawn in parallel, and connected to the extended lines from lower levels. As the results, locally dense packing of lines and figures is avoided. The ordinate of the diagrams indicates level energy, and the J values are shown on the left side of the levels. The wavelength values in angstrom unit are written in parallel with the vertical transition lines. This vertical lines show the resonance transition having absorption oscillator strength f larger than 0.1. The present diagrams are the combination of the tables of wavelength and energy level. Accordingly, the desired wavelength and level energy are easily found. The figures of wavelength are lined up in various groups, so that the characteristics of the transition can be discriminated at a glance. Wavelength and level energy have been mostly derived from experimental spectra in laboratory or solar plasma, except a few by Fawcett's prediction. (Kato, T.)

Use of Influence Diagrams and Fuzzy Theory to Develop Assessment Method of Organizational Influences on Component Maintenance

International Nuclear Information System (INIS)

Yoonik Kim; Kwang-Won Ahn; Chang-Hyun Chung; Kil Yoo Kim; Joon-Eon Yang

2002-01-01

Organization can make influences on all the systems. Especially in case of nuclear power plants in which safety is established to be one of the most important operating goals, there have been a lot of research efforts for the hardware advancement. However in recent years, it has been widely recognized that organizational factors in nuclear power plants have an important influence on the safety attitudes and the safe behavior of individuals. Until now, any means to include assessments of organizational structure in probabilistic risk assessments have not been universally accepted. The objective of this work is to develop a method to assess organizational influences on component maintenance. Influence diagrams are introduced in this method as a decision making tool and fuzzy theory is used to reflect the vagueness in considering relevance of human activities in maintenance tasks. Introducing fuzzy theory to assess the organizational factors is deemed to a somewhat new trial, which makes it possible to convert linguistic vague descriptions into mathematical ones. Fuzzy linguistic descriptions offer an alternative and often complementary language to conventional, i.e., analytic approaches to modeling systems. Among the existing methodologies to assess organizational factors, the concept of the ω-factor model is utilized and the mechanism that organizational factors have influences on component maintenance is evaluated through composing influence diagrams. These influences go to failure rates and eventually affect component unavailability. Further study will make it possible that the influences of organizational factors on human error probabilities are incorporated into human reliability analysis and furthermore probabilistic safety assessment. (authors)

Triangular Diagrams Teach Steady and Dynamic Behaviour of Catalytic Reactions.

Science.gov (United States)

Klusacek, K.; And Others

1989-01-01

Illustrates how triangular diagrams can aid in presenting some of the rather complex transient interactions that occur among gas and surface species during heterogeneous catalytic reactions. The basic equations and numerical examples are described. Classroom use of the triangular diagram is discussed. Several diagrams and graphs are provided. (YP)

Analysis of Sequence Diagram Layout in Advanced UML Modelling Tools

Directory of Open Access Journals (Sweden)

Ņikiforova Oksana

2016-05-01

Full Text Available System modelling using Unified Modelling Language (UML is the task that should be solved for software development. The more complex software becomes the higher requirements are stated to demonstrate the system to be developed, especially in its dynamic aspect, which in UML is offered by a sequence diagram. To solve this task, the main attention is devoted to the graphical presentation of the system, where diagram layout plays the central role in information perception. The UML sequence diagram due to its specific structure is selected for a deeper analysis on the elements’ layout. The authors research represents the abilities of modern UML modelling tools to offer automatic layout of the UML sequence diagram and analyse them according to criteria required for the diagram perception.

Probabilistic safety assessment model in consideration of human factors based on object-oriented bayesian networks

International Nuclear Information System (INIS)

Zhou Zhongbao; Zhou Jinglun; Sun Quan

2007-01-01

Effect of Human factors on system safety is increasingly serious, which is often ignored in traditional probabilistic safety assessment methods however. A new probabilistic safety assessment model based on object-oriented Bayesian networks is proposed in this paper. Human factors are integrated into the existed event sequence diagrams. Then the classes of the object-oriented Bayesian networks are constructed which are converted to latent Bayesian networks for inference. Finally, the inference results are integrated into event sequence diagrams for probabilistic safety assessment. The new method is applied to the accident of loss of coolant in a nuclear power plant. the results show that the model is not only applicable to real-time situation assessment, but also applicable to situation assessment based certain amount of information. The modeling complexity is kept down and the new method is appropriate to large complex systems due to the thoughts of object-oriented. (authors)

Vesicle computers: Approximating a Voronoi diagram using Voronoi automata

International Nuclear Information System (INIS)

Adamatzky, Andrew; De Lacy Costello, Ben; Holley, Julian; Gorecki, Jerzy; Bull, Larry

2011-01-01

Highlights: → We model irregular arrangements of vesicles filled with chemical systems. → We examine influence of precipitation threshold on the system's computational potential. → We demonstrate computation of Voronoi diagram and skeleton. - Abstract: Irregular arrangements of vesicles filled with excitable and precipitating chemical systems are imitated by Voronoi automata - finite-state machines defined on a planar Voronoi diagram. Every Voronoi cell takes four states: resting, excited, refractory and precipitate. A resting cell excites if it has at least one neighbour in an excited state. The cell precipitates if the ratio of excited cells in its neighbourhood versus the number of neighbours exceeds a certain threshold. To approximate a Voronoi diagram on Voronoi automata we project a planar set onto the automaton lattice, thus cells corresponding to data-points are excited. Excitation waves propagate across the Voronoi automaton, interact with each other and form precipitate at the points of interaction. The configuration of the precipitate represents the edges of an approximated Voronoi diagram. We discover the relationship between the quality of the Voronoi diagram approximation and the precipitation threshold, and demonstrate the feasibility of our model in approximating Voronoi diagrams of arbitrary-shaped objects and in constructing a skeleton of a planar shape.

Study on the creation and destruction of transport barriers via the effective safety factors for energetic particles

Science.gov (United States)

Ogawa, Shun; Leoncini, Xavier; Dif-Pradalier, Guilhem; Garbet, Xavier

2016-12-01

Charged particles with low kinetic energy move along the magnetic field lines, but so do not the energetic particles. We investigate the topological structure changes in the phase space of energetic particles with respect to the magnetic one. For this study, cylindrical magnetic fields with non-monotonic safety factors that induce the magnetic internal transport barrier are considered. We show that the topological structure of the magnetic field line and of the particle trajectories can be quite different. We explain this difference using the concept of an effective particle q-profile. Using this notion, we can investigate the location and existence of resonances for particle orbits that are different from the magnetic ones. These are examined both numerically by integrating an equation of motion and theoretically by the use of Alfvén's guiding center theory and by the use of an effective reduced Hamiltonian for the integrable unperturbed system. It is clarified that, for the energetic particles, the grad B drift effect shifts the resonances and the drift induced by curvature of the magnetic field line leads to the vanishing of the resonances. As a result, we give two different mechanisms that lead to the creation of transport barriers for energetic particles in the region where the magnetic field line is chaotic.

Developing Tool Support for Problem Diagrams with CPN and VDM++

DEFF Research Database (Denmark)

Tjell, Simon; Lassen, Kristian Bisgaard

2008-01-01

In this paper, we describe ongoing work on the development of tool support for formal description of domains found in Problem Diagrams. The purpose of the tool is to handle the generation of a CPN model based on a collection of Problem Diagrams. The Problem Diagrams are used for representing the ...

A Generalized Wave Diagram for Moving Sources

Science.gov (United States)

Alt, Robert; Wiley, Sam

2004-12-01

Many introductory physics texts1-5 accompany the discussion of the Doppler effect and the formation of shock waves with diagrams illustrating the effect of a source moving through an elastic medium. Typically these diagrams consist of a series of equally spaced dots, representing the location of the source at different times. These are surrounded by a series of successively smaller circles representing wave fronts (see Fig. 1). While such a diagram provides a clear illustration of the shock wave produced by a source moving at a speed greater than the wave speed, and also the resultant pattern when the source speed is less than the wave speed (the Doppler effect), the texts do not often show the details of the construction. As a result, the key connection between the relative distance traveled by the source and the distance traveled by the wave is not explicitly made. In this paper we describe an approach emphasizing this connection that we have found to be a useful classroom supplement to the usual text presentation. As shown in Fig. 2 and Fig. 3, the Doppler effect and the shock wave can be illustrated by diagrams generated by the construction that follows.

Testing of multidimensional tectonomagmatic discrimination diagrams on fresh and altered rocks

Directory of Open Access Journals (Sweden)

Rivera-Gómez M. Abdelaly

2016-04-01

Full Text Available We evaluated 55 multidimensional diagrams proposed during 2004-2013 for the tectonic discrimination of ultrabasic, basic, intermediate, and acid magmas. The Miocene to Recent rock samples for testing the diagrams had not been used for constructing them. Eighteen test studies (2 from ocean island; 2 from ocean island/continental rift; 6 from continental rift; 4 from continental arc; 2 from island arc; 1 from mid-ocean ridge, and 1 from collision of relatively fresh rocks fully confirmed the satisfactory functioning of these diagrams for all tectonic fields for which they were proposed. Eight additional case studies on hydrothermally altered or moderately to highly weathered rocks were also presented to achieve further understanding of the functioning of these diagrams. For these rocks as well, the diagrams indicated the expected tectonic setting. We also show that for testing or using these diagrams the freely-available geochemistry databases should be used with caution but certainly after ascertaining the correct magma types to select the appropriate diagram sets. The results encourage us to recommend these diagrams for deciphering the tectonic setting of older terranes or areas with complex or transitional tectonic settings.

Logical and Geometrical Distance in Polyhedral Aristotelian Diagrams in Knowledge Representation

Directory of Open Access Journals (Sweden)

Lorenz Demey

2017-09-01

Full Text Available Aristotelian diagrams visualize the logical relations among a finite set of objects. These diagrams originated in philosophy, but recently, they have also been used extensively in artificial intelligence, in order to study (connections between various knowledge representation formalisms. In this paper, we develop the idea that Aristotelian diagrams can be fruitfully studied as geometrical entities. In particular, we focus on four polyhedral Aristotelian diagrams for the Boolean algebra B 4 , viz. the rhombic dodecahedron, the tetrakis hexahedron, the tetraicosahedron and the nested tetrahedron. After an in-depth investigation of the geometrical properties and interrelationships of these polyhedral diagrams, we analyze the correlation (or lack thereof between logical (Hamming and geometrical (Euclidean distance in each of these diagrams. The outcome of this analysis is that the Aristotelian rhombic dodecahedron and tetrakis hexahedron exhibit the strongest degree of correlation between logical and geometrical distance; the tetraicosahedron performs worse; and the nested tetrahedron has the lowest degree of correlation. Finally, these results are used to shed new light on the relative strengths and weaknesses of these polyhedral Aristotelian diagrams, by appealing to the congruence principle from cognitive research on diagram design.

Mollier-h,x diagram for moist flue gas

Energy Technology Data Exchange (ETDEWEB)

Mueller, H; Hultsch, T; Suder, M

1984-07-01

Diagrams and formulae are presented for calculation of enthalpy and moisture content of flue gas from brown coal, heating oil, black coal and brown coal briquet combustion. The enthalpy (in kJ/kg) and moisture (g/kg) diagrams were established by computer graphics for pressure 0.1 MPa. A further diagram is provided for enthalpy and flue gas moisture, varying the combustion air supply according to coal dust and to grate firing. These thermodynamic calculations are regarded as significant for assessing methods of flue gas cooling below the moisture dew point and for waste heat recovery. 3 references.

Research principles and the construction of mnemonic diagrams

Science.gov (United States)

Venda, V. F.; Mitkin, A. A.

1973-01-01

Mnemonic diagrams are defined as a variety of information display devices, the essential element of which is conventional graphical presentation of technological or functional-operational links in a controlled system or object. Graphically displaying the operational structure of an object, the interd dependence between different parameters, and the interdependence between indicators and control organs, the mneomonic diagram reduces the load on the operator's memory and facilitates perception and reprocessing of information and decision making, while at the same time playing the role of visual support to the information activity of the operator. The types of mnemonic diagrams are listed.

Nuclear Reactor RA Safety Report, Vol. 14, Safety protection measures

International Nuclear Information System (INIS)

1986-11-01

Nuclear reactor accidents can be caused by three type of errors: failure of reactor components including (1) control and measuring instrumentation, (2) errors in operation procedure, (3) natural disasters. Safety during reactor operation are secured during its design and construction and later during operation. Both construction and administrative procedures are applied to attain safe operation. Technical safety features include fission product barriers, fuel elements cladding, primary reactor components (reactor vessel, primary cooling pipes, heat exchanger in the pump), reactor building. Safety system is the system for safe reactor shutdown and auxiliary safety system. RA reactor operating regulations and instructions are administrative acts applied to avoid possible human error caused accidents [sr

Infrared thermography method for fast estimation of phase diagrams

Energy Technology Data Exchange (ETDEWEB)

Palomo Del Barrio, Elena [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Cadoret, Régis [Centre National de la Recherche Scientifique, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France); Daranlot, Julien [Solvay, Laboratoire du Futur, 178 Av du Dr Schweitzer, 33608 Pessac (France); Achchaq, Fouzia, E-mail: fouzia.achchaq@u-bordeaux.fr [Université de Bordeaux, Institut de Mécanique et d’Ingénierie, Esplanade des Arts et Métiers, 33405 Talence (France)

2016-02-10

Highlights: • Infrared thermography is proposed to determine phase diagrams in record time. • Phase boundaries are detected by means of emissivity changes during heating. • Transition lines are identified by using Singular Value Decomposition techniques. • Different binary systems have been used for validation purposes. - Abstract: Phase change materials (PCM) are widely used today in thermal energy storage applications. Pure PCMs are rarely used because of non adapted melting points. Instead of them, mixtures are preferred. The search of suitable mixtures, preferably eutectics, is often a tedious and time consuming task which requires the determination of phase diagrams. In order to accelerate this screening step, a new method for estimating phase diagrams in record time (1–3 h) has been established and validated. A sample composed by small droplets of mixtures with different compositions (as many as necessary to have a good coverage of the phase diagram) deposited on a flat substrate is first prepared and cooled down to ambient temperature so that all droplets crystallize. The plate is then heated at constant heating rate up to a sufficiently high temperature for melting all the small crystals. The heating process is imaged by using an infrared camera. An appropriate method based on singular values decomposition technique has been developed to analyze the recorded images and to determine the transition lines of the phase diagram. The method has been applied to determine several simple eutectic phase diagrams and the reached results have been validated by comparison with the phase diagrams obtained by Differential Scanning Calorimeter measurements and by thermodynamic modelling.

A holistic view on Safety Management

DEFF Research Database (Denmark)

Jørgensen, Kirsten

to prevent accidents is to identify the risks in all kinds of situations and take precautions by establishing safety barriers either technically or by improving the processes involved in managing these barriers, as well as bringing about behavioral improvements through good leadership. A project initiated...

Correlation diagram approach to the dissociative ionization mechanisms of methanol

International Nuclear Information System (INIS)

Momigny, J.; Wankenne, H.; Krier, C.

1980-01-01

A systematic survey is made of the dissociation processes from the ground state and from the electronically excited states of CH 3 OH + . Most metastable processes occurring in the mass spectrum of CD 3 OH are studied also, including measurement of the kinetic energy release and appearance potentials. It is shown that if ionic species such as CH 2 OH + , CH 2 O + and HCO + are present in the mass spectrum of CH 3 OH, the isomers CH 3 O + , HCOH + and COH + are also present. The precursors of these ions having been identified by the metastable processes, correlation diagrams are used to show that, from the first ionization potential of CH 3 OH to 14 eV, the only exception being CH 3 O + which results from an electronically spin-forbidden predissociation, the fragment ions can be considered to result from adiabatic decay of the ground state of CH 3 OH + . The potential barriers involved in these adiabatic processes result either from conical intersection or from avoided-crossing between the ground state of CH 3 OH + and the electronically excited states occurring up to 14 eV. At higher energies, many non-adiabatic processes occur; for example, the appearance of CD 2 O + and the electronically excited states of HCO + and COH + ions. It is shown additionally that kinetic energy releases observed in the collision-induced processes CH 3 OH + → CH 2 OH + + H and CH 2 OH + → HCO + + H 2 are in good agreement with the mechanistic approach via the correlation diagram for the appearance of the non-collision-induced ion processes. (orig.)

Improvements in Logic Diagram of Computerized Procedure System of APR1400

Energy Technology Data Exchange (ETDEWEB)

Kang, Sungkweon; Seong, Nokyu [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The Computerized Procedure System (CPS) has been improved since it is installed in Shin-Kori 3 and 4 Nuclear Power Plants. It is one of operating support systems of digital Main Control Room (MCR) and provides many functions to operators in executing the procedure. CPS can effectively remove the human errors by supporting the procedure flow and logic diagram. This paper describes the logic diagram of CPS of reference power plant and shows the improved logic diagram of CPS of Shin-Kori unit 5 and 6. This paper describes the current logic diagram of CPS and suggests improved design for logic diagram. The improved logic diagram shall be validated through human factors engineering verification and validation. The improved design will help operators execute the computerized procedure fast and remove the human error.

Ferrocyanide Safety Program: Data requirements for the ferrocyanide safety issue developed through the data quality objectives (DQO) process

International Nuclear Information System (INIS)

Buck, J.W.; Anderson, C.M.; Pulsipher, B.A.; Toth, J.J.; Turner, P.J.; Cash, R.J.; Dukelow, G.T.; Meacham, J.E.

1993-12-01

This document records the data quality objectives (DQO) process applied to the Ferrocyanide Waste Tank Safety Issue at the Hanford Site by the Pacific Northwest Laboratory and Westinghouse Hanford Company. Specifically, the major recommendations and findings from this Ferrocyanide DQO process are presented so that decision makers can determine the type, quantity, and quality of data required for addressing tank safety issues. The decision logic diagrams and error tolerance equations also are provided. Finally, the document includes the DQO sample-size formulas for determining specific tank sampling requirements

Safety of geologic disposal of high level radioactive waste

International Nuclear Information System (INIS)

Zaitsu, Tomohisa; Ishiguro, Katsuhiko; Masuda, Sumio

1992-01-01

This article introduces current concepts of geologic disposal of high level radioactive waste and its safety. High level radioactive waste is physically stabilized by solidifying it in a glass form. Characteristics of deep geologic layer are presented from the viewpoint of geologic disposal. Reconstruction of multi-barrier system receives much attention to secure the safety of geologic disposal. It is important to research performance assessment of multi-barrier system for preventing dissolution or transfer of radionuclides into the ground water. Physical and chemical modeling for the performance assessment is outlined in the following terms: (1) chemical property of deep ground water, (2) geochemical modeling of artificial barrier spatial water, (3) hydrology of deep ground water, (4) hydrology of the inside of artificial barrier, and (5) modeling of radionuclide transfer from artificial barrier. (N.K.)

State diagram of Pr-Bi system

International Nuclear Information System (INIS)

Abulkhaev, V.L.; Ganiev, I.N.

1994-01-01

By means of thermal differential analysis, X-ray and microstructural analysis the state diagram of Pr-Bi system was studied. Following intermetallic compounds were defined in the system: Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 , Pr Bi, PrBi 2 , Pr 2 Bi, Pr 5 Bi 3 , Pr 4 Bi 3 and PrBi 2 . The data analysis on Ln-Bi diagram allowed to determine the regularity of change of properties of intermetallic compounds in the line of rare earth elements of cerium subgroup.

Fusion Diagrams in the - and - Systems

Science.gov (United States)

Asadov, M. M.; Akhmedova, N. A.

2014-10-01

A calculation model of the Gibbs energy of ternary oxide compounds from the binary components was used. Thermodynamic properties of -- ternary systems in the condensed state were calculated. Thermodynamic data of binary and ternary compounds were used to determine the stable sections. The probability of reactions between the corresponding components in the -- system was estimated. Fusibility diagrams of systems - and - were studied by physical-chemical analysis. The isothermal section of the phase diagram of -- at 298 K is built, as well as the projection of the liquid surface of --.

An Application of Mosaic Diagrams to the Visualization of Set Relationships

OpenAIRE

Luz, Saturnino; Masoodian, Masood

2017-01-01

We present an application of mosaic diagrams to the visualisation of set relations. Venn and Euler diagrams are the best known visual representations of sets and their relationships (intersections, containment or subsets, exclusion or disjointness). In recent years, alternative forms of visualisation have been proposed. Among them, linear diagrams have been shown to compare favourably to Venn and Euler diagrams, in supporting non-interactive assessment of set relationships. Recent studies tha...

Engineered safeguards and passive safety features (safety analysis detailed report no. 6)

Energy Technology Data Exchange (ETDEWEB)

1988-01-15

The Safety-Analysis Summary lists the reactor's safety aspects for passive and active prevention of severe accidents and mitigation of accident consequences, i.e., intrinsic and passive protections of the plant; intrinsic and passive protections of the core; inherent decay-heat removal systems; rapid-shutdown systems; four physical containment barriers. This report goes into further details regarding some of this aspects.

Characterization strategy for the flammable gas safety issue

International Nuclear Information System (INIS)

Stewart, C.W.; Brewster, M.E.; Roberts, J.S.

1997-06-01

The characterization strategy for resolving the flammable gas safety issue for Hanford waste tanks is based on a structured logic diagram (SLD) that displays the outcomes necessary to reach the desired goal of making flammable gas risk acceptable. The diagram provides a structured path that can identify all information inputs, data as well as models, needed to achieve the goal. Tracing the path from need to outcome provides an immediate and clear justification and defense of a specific need. The diagram itself is a open-quote picture of a risk calculation close-quote and forms the basis for a quantitative model of risk. The SLID, with the risk calculation, identifies options for characterization, mitigation, and controls that have the maximum effect in reducing risk. It provides quantitative input to risk-based decision making so that options are chosen for maximum impact at least cost

Plotting and Analyzing Data Trends in Ternary Diagrams Made Easy

Science.gov (United States)

John, Cédric M.

2004-04-01

Ternary plots are used in many fields of science to characterize a system based on three components. Triangular plotting is thus useful to a broad audience in the Earth sciences and beyond. Unfortunately, it is typically the most expensive commercial software packages that offer the option to plot data in ternary diagrams, and they lack features that are paramount to the geosciences, such as the ability to plot data directly into a standardized diagram and the possibility to analyze temporal and stratigraphic trends within this diagram. To address these issues, δPlot was developed with a strong emphasis on ease of use, community orientation, and availability free of charges. This ``freeware'' supports a fully graphical user interface where data can be imported as text files, or by copying and pasting. A plot is automatically generated, and any standard diagram can be selected for plotting in the background using a simple pull-down menu. Standard diagrams are stored in an external database of PDF files that currently holds some 30 diagrams that deal with different fields of the Earth sciences. Using any drawing software supporting PDF, one can easily produce new standard diagrams to be used with δPlot by simply adding them to the library folder. An independent column of values, commonly stratigraphic depths or ages, can be used to sort the data sets.

Adding Value to Force Diagrams: Representing Relative Force Magnitudes

Science.gov (United States)

Wendel, Paul

2011-05-01

Nearly all physics instructors recognize the instructional value of force diagrams, and this journal has published several collections of exercises to improve student skill in this area.1-4 Yet some instructors worry that too few students perceive the conceptual and problem-solving utility of force diagrams,4-6 and over recent years a rich variety of approaches has been proposed to add value to force diagrams. Suggestions include strategies for identifying candidate forces,6,7 emphasizing the distinction between "contact" and "noncontact" forces,5,8 and the use of computer-based tutorials.9,10 Instructors have suggested a variety of conventions for constructing force diagrams, including approaches to arrow placement and orientation2,11-13 and proposed notations for locating forces or marking action-reaction force pairs.8,11,14,15

Phase diagram of an extended Agassi model

Science.gov (United States)

García-Ramos, J. E.; Dukelsky, J.; Pérez-Fernández, P.; Arias, J. M.

2018-05-01

Background: The Agassi model [D. Agassi, Nucl. Phys. A 116, 49 (1968), 10.1016/0375-9474(68)90482-X] is an extension of the Lipkin-Meshkov-Glick (LMG) model [H. J. Lipkin, N. Meshkov, and A. J. Glick, Nucl. Phys. 62, 188 (1965), 10.1016/0029-5582(65)90862-X] that incorporates the pairing interaction. It is a schematic model that describes the interplay between particle-hole and pair correlations. It was proposed in the 1960s by D. Agassi as a model to simulate the properties of the quadrupole plus pairing model. Purpose: The aim of this work is to extend a previous study by Davis and Heiss [J. Phys. G: Nucl. Phys. 12, 805 (1986), 10.1088/0305-4616/12/9/006] generalizing the Agassi model and analyze in detail the phase diagram of the model as well as the different regions with coexistence of several phases. Method: We solve the model Hamiltonian through the Hartree-Fock-Bogoliubov (HFB) approximation, introducing two variational parameters that play the role of order parameters. We also compare the HFB calculations with the exact ones. Results: We obtain the phase diagram of the model and classify the order of the different quantum phase transitions appearing in the diagram. The phase diagram presents broad regions where several phases, up to three, coexist. Moreover, there is also a line and a point where four and five phases are degenerated, respectively. Conclusions: The phase diagram of the extended Agassi model presents a rich variety of phases. Phase coexistence is present in extended areas of the parameter space. The model could be an important tool for benchmarking novel many-body approximations.

Single-particle potential from resummed ladder diagrams

International Nuclear Information System (INIS)

Kaiser, N.

2013-01-01

A recent work on the resummation of fermionic in-medium ladder diagrams to all orders is extended by calculating the complex single-particle potential U(p, k f ) + i W(p, k f ) p > k f . The on-shell single-particle potential is constructed by means of a complex-valued in-medium loop that includes corrections from a test particle of momentum vector p added to the filled Fermi sea. The single-particle potential U(k f , k f ) at the Fermi surface as obtained from the resummation of the combined particle and hole ladder diagrams is shown to satisfy the Hugenholtz-Van-Hove theorem. The perturbative contributions at various orders a n in the scattering length are deduced and checked against the known analytical results at order a 1 and a 2 . The limit a → ∞ is studied as a special case and a strong momentum dependence of the real (and imaginary) single-particle potential is found. This feature indicates an instability against a phase transition to a state with an empty shell inside the Fermi sphere such that the density gets reduced by about 5%. The imaginary single-particle potential vanishes linearly at the Fermi surface. For comparison, the same analysis is performed for the resummed particle-particle ladder diagrams alone. In this truncation an instability for hole excitations near the Fermi surface is found at strong coupling. For the set of particle-hole ring diagrams the single-particle potential is calculated as well. Furthermore, the resummation of in-medium ladder diagrams to all orders is studied for a two-dimensional Fermi gas with a short-range two-body contact interaction. (orig.)

Refined phase diagram of boron nitride

International Nuclear Information System (INIS)

Solozhenko, V.; Turkevich, V.Z.

1999-01-01

The equilibrium phase diagram of boron nitride thermodynamically calculated by Solozhenko in 1988 has been now refined on the basis of new experimental data on BN melting and extrapolation of heat capacities of BN polymorphs into high-temperature region using the adapted pseudo-Debye model. As compared with the above diagram, the hBN left-reversible cBN equilibrium line is displaced by 60 K toward higher temperatures. The hBN-cBN-L triple point has been calculated to be at 3480 ± 10 K and 5.9 ± 0.1 GPa, while the hBN-L-V triple point is at T = 3400 ± 20 K and p = 400 ± 20 Pa, which indicates that the region of thermodynamic stability of vapor in the BN phase diagram is extremely small. It has been found that the slope of the cBN melting curve is positive whereas the slope of hBN melting curve varies from positive between ambient pressure and 3.4 GPa to negative at higher pressures

Human Factors and Safety Culture in Maritime Safety (revised

Directory of Open Access Journals (Sweden)

Heinz Peter Berg

2013-09-01

Full Text Available As in every industry at risk, the human and organizational factors constitute the main stakes for maritime safety. Furthermore, several events at sea have been used to develop appropriate risk models. The investigation on maritime accidents is, nowadays, a very important tool to identify the problems related to human factor and can support accident prevention and the improvement of maritime safety. Part of this investigation should in future also be near misses. Operation of ships is full of regulations, instructions and guidelines also addressing human factors and safety culture to enhance safety. However, even though the roots of a safety culture have been established, there are still serious barriers to the breakthrough of the safety management. One of the most common deficiencies in the case of maritime transport is the respective monitoring and documentation usually lacking of adequacy and excellence. Nonetheless, the maritime area can be exemplified from other industries where activities are ongoing to foster and enhance safety culture.

More asymptotic safety guaranteed

Science.gov (United States)

Bond, Andrew D.; Litim, Daniel F.

2018-04-01

We study interacting fixed points and phase diagrams of simple and semisimple quantum field theories in four dimensions involving non-Abelian gauge fields, fermions and scalars in the Veneziano limit. Particular emphasis is put on new phenomena which arise due to the semisimple nature of the theory. Using matter field multiplicities as free parameters, we find a large variety of interacting conformal fixed points with stable vacua and crossovers inbetween. Highlights include semisimple gauge theories with exact asymptotic safety, theories with one or several interacting fixed points in the IR, theories where one of the gauge sectors is both UV free and IR free, and theories with weakly interacting fixed points in the UV and the IR limits. The phase diagrams for various simple and semisimple settings are also given. Further aspects such as perturbativity beyond the Veneziano limit, conformal windows, and implications for model building are discussed.

Phase diagrams of diluted transverse Ising nanowire

International Nuclear Information System (INIS)

Bouhou, S.; Essaoudi, I.; Ainane, A.; Saber, M.; Ahuja, R.; Dujardin, F.

2013-01-01

In this paper, the phase diagrams of diluted Ising nanowire consisting of core and surface shell coupling by J cs exchange interaction are studied using the effective field theory with a probability distribution technique, in the presence of transverse fields in the core and in the surface shell. We find a number of characteristic phenomena. In particular, the effect of concentration c of magnetic atoms, the exchange interaction core/shell, the exchange in surface and the transverse fields in core and in surface shell of phase diagrams are investigated. - Highlights: ► We use the EFT to investigate the phase diagrams of Ising transverse nanowire. ► Ferrimagnetic and ferromagnetic cases are investigated. ► The effects of the dilution and the transverse fields in core and shell are studied. ► Behavior of the transition temperature with the exchange interaction is given

Homotopy Diagrams of Algebras

Czech Academy of Sciences Publication Activity Database

Markl, Martin

2002-01-01

Roč. 69, - (2002), s. 161-180 ISSN 0009-725X. [Winter School "Geometry and Physics" /21./. Srní, 13.01.2001-20.01.2001] R&D Projects: GA ČR GA201/99/0675 Keywords : colored operad%cofibrant model%homotopy diagram Subject RIV: BA - General Mathematics

Random Young diagrams in a Rectangular Box

DEFF Research Database (Denmark)

Beltoft, Dan; Boutillier, Cédric; Enriquez, Nathanaël

We exhibit the limit shape of random Young diagrams having a distribution proportional to the exponential of their area, and confined in a rectangular box. The Ornstein-Uhlenbeck bridge arises from the fluctuations around the limit shape.......We exhibit the limit shape of random Young diagrams having a distribution proportional to the exponential of their area, and confined in a rectangular box. The Ornstein-Uhlenbeck bridge arises from the fluctuations around the limit shape....

Improved HEPA Filter Technology for Flexible and Rigid Containment Barriers

International Nuclear Information System (INIS)

Pinson, Paul Arthur

1998-01-01

Safety and reliability in glovebox operations can be significantly improved and waste packaging efficiencies can be increased by inserting flexible, lightweight, high capacity HEPA filters into the walls of plastic sheet barriers. This HEPA filter/barrier technology can be adapted to a wide variety of applications: disposable waste bags, protective environmental barriers for electronic equipment, single or multiple use glovebag assemblies, flexible glovebox wall elements, and room partitions. These reliable and inexpensive filtered barriers have many uses in fields such as radioactive waste processing, HVAC filter changeout, vapor or grit blasting, asbestos cleanup, pharmaceutical, medical, biological, and electronic equipment containment. The applications can result in significant cost savings, improved operational reliability and safety, and total waste volume reduction. This technology was developed at the Argonne National Laboratory-West (ANL-W) in 1993 and has been used at ANL-W since then at the TRU Waste Characterization Chamber Gloveboxes. Another 1998 AGS Conference paper titled ''TRU Waste Characterization Gloveboxes'', presented by Mr. David Duncan of ANL-W, describes these boxes

Experimental study of fire barriers preventing vertical fire spread in ETISs

Directory of Open Access Journals (Sweden)

Xin Huang

2013-11-01

Full Text Available In recent years, the external thermal insulation system (ETIS has been applied increasingly in a large amount of buildings for energy conservation purpose. However, the increase use of combustible insulation materials in the ETIS has raised serious fire safety problems. Fires involving this type of ETIS have caused severe damage and loss. In order to improve its fire safety, fire barriers were suggested to be installed. This paper introduces fire experiments that have been done to study the effects of fire barriers on preventing vertical fire spread along the ETIS. The experiments were performed according to BS 8414-1:2002 “Fire performance of external cladding systems – Part 1: Test method for non-loadbearing external cladding systems applied to the face of the building”. The test facility consists of a 9 m high wall. The fire sources were wood cribs with a fire size of 3 ± 0.5 MW. The insulation materials were expanded polystyrene foam (EPS. The fire barrier was a horizontal strip of rockwool with a width of 300 mm. Thermocouples were used to measure temperatures outside and inside the ETIS. A series of experiments with different fire scenarios were done: no fire barrier, two fire barriers and three fire barriers at different heights. Test results were compared. The results show that the ETIS using EPS without fire barriers almost burned out, while the ETIS with fire barriers performed well in preventing fire spread. The temperatures above the fire barrier were much lower than those below the fire barrier, and most of the insulation materials above the top fire barrier stayed in place.

Teaching With Projections in the Geosciences: Windows to Enlightenment or Barriers to Understanding?

Science.gov (United States)

Mogk, D. W.

2009-12-01

Geoscientists are trained to represent multi-component datasets by projecting onto relatively simple diagrams on two-dimensional surfaces. These projections are used to represent a variety of phenomena ranging from spatial relations to physico-chemical processes. By using projections, it is possible to create simple diagrams as models or analogs of complex and heterogeneous natural systems using a limited number of well-defined “end-member” variables. Although projections are widely used in professional practice, the construction, use and interpretation of these diagrams often presents formidable barriers to student learning. This is largely due to the fact that diagrams that display projected data are the composite product of underlying scientific and mathematical principles, spatial relations on the diagrams may serve as proxies for physical or chemical properties or processes (thus co-mingling spatial reasoning with conceptual reasoning), there are myriad hidden or understood assumptions in the creation of the projections, and projections seek to decrease the “dimensionality” (or degrees of freedom) of multi-component (or multi-variable) systems. Additional layers of information may be superposed on projected diagrams by contouring data, using color or other symbols to distinguish discrete populations of data, imposing gradients of related variables (e.g. isotherms on composition diagrams), or using multiple projections to demonstrate time sequences that elucidate processes (e.g. before/after relations conveyed in animations). Thus, the simple forms of graphical projections may belie numerous layers of information that attempt to explain complex and sophisticated relationships in nature. In striving for simplicity in presentation, diagrams that present projected data may confound student understanding due to lack of knowledge about the inherent complexities in their development. Recall Plato’s Myth of the Cave (Republic, Book 7): the shadow on the wall

Formal Analysis Of Use Case Diagrams

Directory of Open Access Journals (Sweden)

Radosław Klimek

2010-01-01

Full Text Available Use case diagrams play an important role in modeling with UML. Careful modeling is crucialin obtaining a correct and efficient system architecture. The paper refers to the formalanalysis of the use case diagrams. A formal model of use cases is proposed and its constructionfor typical relationships between use cases is described. Two methods of formal analysis andverification are presented. The first one based on a states’ exploration represents a modelchecking approach. The second one refers to the symbolic reasoning using formal methodsof temporal logic. Simple but representative example of the use case scenario verification isdiscussed.

Phase Stability Diagrams for High Temperature Corrosion Processes

Directory of Open Access Journals (Sweden)

J. J. Ramos-Hernandez

2013-01-01

Full Text Available Corrosion phenomena of metals by fused salts depend on chemical composition of the melt and environmental conditions of the system. Detail knowledge of chemistry and thermodynamic of aggressive species formed during the corrosion process is essential for a better understanding of materials degradation exposed to high temperature. When there is a lack of kinetic data for the corrosion processes, an alternative to understand the thermodynamic behavior of chemical species is to utilize phase stability diagrams. Nowadays, there are several specialized software programs to calculate phase stability diagrams. These programs are based on thermodynamics of chemical reactions. Using a thermodynamic data base allows the calculation of different types of phase diagrams. However, sometimes it is difficult to have access to such data bases. In this work, an alternative way to calculate phase stability diagrams is presented. The work is exemplified in the Na-V-S-O and Al-Na-V-S-O systems. This system was chosen because vanadium salts is one of the more aggressive system for all engineering alloys, especially in those processes where fossil fuels are used.

Resonant count diagram and solar g mode oscillations

International Nuclear Information System (INIS)

Guenther, D.B.; Demarque, P.

1984-01-01

Evidence is provided to support the hypothesis that, because of the particular frequency separations of the solar g modes, resonant three-wave interactions stimulate only a selected few g modes. A resonant count diagram was obtained by plotting the total number of possible resonant three-wave interactions or a given beat frequency against the inverse of the beat frequency (the beat period), within a given frequency tolerance. The 1 = 1, 2, 3, 4 g modes calculated by Christensen-Dalsgaard, Gough and Morgan (1979) for a standard model of the Sun were used. The diagram has a significant peak at 160 minutes as well as other peaks at longer periods. The g modes that Delache and Scherrer (1983) tentatively identified from the Crimea-Stanford data were also plotted. These modes were found to correspond with the other peaks in the diagram. This coincidence between the observed g modes and the peaks in the resonant count diagram suggest that the observed g modes do owe their observability to resonant three-wave interactions

Comparisons between observational color-magnitude diagrams and synthetic cluster diagrams for young star clusters in the Magellanic Clouds

International Nuclear Information System (INIS)

Recker, S.A.; Brunish, W.M.; Mathews, G.J.

1984-01-01

Young star clusters ( 8 yr) in the Magellanic Clouds (MC) can be used to test the current status of the theory of stellar evolution as applied to intermediate and massive stars. The color-magnitude diagram of many young clusters in the MC shows large numbers of stars in both the main sequence and post main sequence evolutionary phases. Using a grid of stellar evolution models, synthetic cluster H-R diagrams are constructed and compared to observed color-magnitude diagrams to determine the age, age spread, and composition for any given cluster. In addition, for those cases where the data is of high quality, detailed comparisons between theory and observation can provide a diagnostic of the accuracy of the stellar evolution models. Initial indications of these comparisons suggest that the theoretical models should be altered to include: a larger value for the mixing length parameter, a larger rate of mass loss during the asymptotic giant branch phase, and possibly convective overshoot during the core burning phases. (Auth.)

Converse Theorems for Safety and Barrier Certificates

Czech Academy of Sciences Publication Activity Database

Ratschan, Stefan

Online 11 January 2018. (2018) ISSN 0018-9286 R&D Projects: GA ČR GA15-14484S Institutional support: RVO:67985807 Keywords : Safety * Robustness * Radio frequency * Differential equations * Tools * Computer science * Controllability Subject RIV: IN - Informatics, Computer Science Impact factor: 4.270, year: 2016

The Barrier code for predicting long-term concrete performance

International Nuclear Information System (INIS)

Shuman, R.; Rogers, V.C.; Shaw, R.A.

1989-01-01

There are numerous features incorporated into a LLW disposal facility that deal directly with critical safety objectives required by the NRC in 10 CFR 61. Engineered barriers or structures incorporating concrete are commonly being considered for waste disposal facilities. The Barrier computer code calculates the long-term degradation of concrete structures in LLW disposal facilities. It couples this degradation with water infiltration into the facility, nuclide leaching from the waste, contaminated water release from the facility, and associated doses to members of the critical population group. The concrete degradation methodology of Barrier is described

Revised Pourbaix diagrams for Copper at 5-150 C

International Nuclear Information System (INIS)

Beverskog, B.; Puigdomenech, I.

1995-10-01

Pourbaix diagrams have been revised. Predominance diagrams for dissolved copper species have also been calculated. Five different total concentrations for dissolved copper have been used in the calculations (from 10 -3 to 10 -9 ). The complete hydrolysis series of copper(I) and (II) have not been included in earlier published Pourbaix diagrams, and these species are covered for the first time in this work. At acidic pH, increasing temperature decreases the immunity area, and therefore, it increases the corrosion of the copper. At alkaline pH-values corrosion also increases with the temperature due to the decrease of both passivity and immunity areas. The calculated diagrams are used as a base for the discussion of the corrosion behaviour of the copper canisters in the Swedish radioactive waste management program. 62 refs, 37 figs, 3 tabs

Solid gas reaction phase diagram under high gas pressure

International Nuclear Information System (INIS)

Ishizaki, K.

1992-01-01

This paper reports that to evaluate which are the stable phases under high gas pressure conditions, a solid-gas reaction phase diagram under high gas pressure (HIP phase diagram) has been proposed by the author. The variables of the diagram are temperature, reactant gas partial pressure and total gas pressure. Up to the present time the diagrams have been constructed using isobaric conditions. In this work, the stable phases for a real HIP process were evaluated assuming an isochoric condition. To understand the effect of the total gas pressure on stability is of primary importance. Two possibilities were considered and evaluated, those are: the total gas pressure acts as an independent variable, or it only affects the fugacity values. The results of this work indicate that the total gas pressure acts as an independent variable, and in turn also affects the fugacity values

Equational binary decision diagrams

NARCIS (Netherlands)

J.F. Groote (Jan Friso); J.C. van de Pol (Jaco)

2000-01-01

textabstractWe incorporate equations in binary decision diagrams (BDD). The resulting objects are called EQ-BDDs. A straightforward notion of ordered EQ-BDDs (EQ-OBDD) is defined, and it is proved that each EQ-BDD is logically equivalent to an EQ-OBDD. Moreover, on EQ-OBDDs satisfiability and

On the Impact of Diagram Layout: How Are Models Actually Read?

DEFF Research Database (Denmark)

Störrle, Harald; Baltsen, Nick; Christoffersen, Henrik

2014-01-01

This poster presents the latest results from a very large eye tracking study (n=29) that explores how modelers read UML diagrams. We find that various factors like layout quality, modeler experience, and diagram type lead to significant differences in diagram reading strategies. We derive elements...

Phase diagrams and switching of voltage and magnetic field in dilute magnetic semiconductor nanostructures

Energy Technology Data Exchange (ETDEWEB)

Escobedo, R. [Departamento de Matematica Aplicada y Ciencias de la Computacion, Universidad de Cantabria, 39005 Santander (Spain); Carretero, M.; Bonilla, L.L. [G. Millan Institute, Fluid Dynamics, Nanoscience and Industrial Maths., Universidad Carlos III de Madrid, 28911 Leganes (Spain); Unidad Asociada al Instituto de Ciencia de Materiales, CSIC, 28049 Cantoblanco, Madrid (Spain); Platero, G. [Instituto de Ciencia de Materiales, CSIC, 28049 Cantoblanco, Madrid (Spain)

2010-04-15

The response of an n-doped dc voltage biased II-VI multi-quantum well dilute magnetic semiconductor nanostructure having its first well doped with magnetic (Mn) impurities is analyzed by sweeping wide ranges of both the voltage and the Zeeman level splitting induced by an external magnetic field. The level splitting versus voltage phase diagram shows regions of stable self-sustained current oscillations immersed in a region of stable stationary states. Transitions between stationary states and self-sustained current oscillations are systematically analyzed by both voltage and level splitting abrupt switching. Sudden voltage or/and magnetic field changes may switch on current oscillations from an initial stationary state, and reciprocally, current oscillations may disappear after sudden changes of voltage or/and magnetic field changes into the stable stationary states region. The results show how to design such a device to operate as a spin injector and a spin oscillator by tuning the Zeeman splitting (through the applied external magnetic field), the applied voltage and the sample configuration parameters (doping density, barrier and well widths, etc.) to select the desired stationary or oscillatory behavior. Phase diagram of Zeeman level splitting {delta} vs. dimensionless applied voltage {phi} for N = 10 QWs. White region: stable stationary states; black: stable self-sustained current oscillations. (copyright 2010 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

A Three-dimensional Topological Model of Ternary Phase Diagram

International Nuclear Information System (INIS)

Mu, Yingxue; Bao, Hong

2017-01-01

In order to obtain a visualization of the complex internal structure of ternary phase diagram, the paper realized a three-dimensional topology model of ternary phase diagram with the designed data structure and improved algorithm, under the guidance of relevant theories of computer graphics. The purpose of the model is mainly to analyze the relationship between each phase region of a ternary phase diagram. The model not only obtain isothermal section graph at any temperature, but also extract a particular phase region in which users are interested. (paper)

A Critical Appraisal of the `Day' Diagram

Science.gov (United States)

Roberts, A. P.; Tauxe, L.; Heslop, D.

2017-12-01

The `Day' diagram [Day et al., 1977; doi:10.1016/0031-9201(77)90108-X] is used widely to infer the mean domain state of magnetic mineral assemblages. The Day plot coordinates are the ratios of the saturation remanent magnetization to saturation magnetization (Mrs/Ms) and the coercivity of remanence to coercivity (Bcr/Bc), as determined from a major hysteresis loop and a backfield demagnetization curve. Based on theoretical and empirical arguments, Day plots are typically demarcated into stable single domain (SD), `pseudosingle domain' (`PSD'), and multidomain (MD) zones. It is a simple task to determine Mrs/Ms and Bcr/Bc for a sample and to assign a mean domain state based on the boundaries defined by Day et al. [1977]. Many other parameters contribute to variability in a Day diagram, including surface oxidation, mineral stoichiometry, stress state, magnetostatic interactions, and mixtures of magnetic particles with different sizes and shapes. Bulk magnetic measurements usually lack detailed independent evidence to constrain each free parameter, which makes the Day diagram fundamentally ambiguous. This raises questions about its usefulness for diagnosing magnetic particle size variations. The Day diagram is also used to make inferences about binary mixing of magnetic particles, where, for example, mixtures of SD and MD particles give rise to a bulk `PSD' response even though the concentration of `PSD' grains could be zero. In our assessment of thousands of hysteresis measurements of geological samples, binary mixing occurs in a tiny number of cases. Ternary, quaternary, and higher order mixing are usually observed. Also, uniaxial SD and MD end-members are nearly always inappropriate for considering mixing because uniaxial SD particles are virtually non-existent in igneous rocks. Thus, use of mixing lines in Day diagrams routinely provides unsatisfactory representations of particle size variations. We critically appraise the Day diagram and argue that its many

Finding and Accessing Diagrams in Biomedical Publications

OpenAIRE

Kuhn, Tobias; Luong, ThaiBinh; Krauthammer, Michael

2012-01-01

Complex relationships in biomedical publications are often communicated by diagrams such as bar and line charts, which are a very effective way of summarizing and communicating multi-faceted data sets. Given the ever-increasing amount of published data, we argue that the precise retrieval of such diagrams is of great value for answering specific and otherwise hard-to-meet information needs. To this end, we demonstrate the use of advanced image processing and classification for identifying bar...

Phase diagrams of diluted transverse Ising nanowire

Energy Technology Data Exchange (ETDEWEB)

Bouhou, S.; Essaoudi, I. [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Ainane, A., E-mail: ainane@pks.mpg.de [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Max-Planck-Institut für Physik Complexer Systeme, Nöthnitzer Str. 38 D-01187 Dresden (Germany); Saber, M. [Laboratoire de Physique des Matériaux et Modélisation, des Systèmes, (LP2MS), Unité Associée au CNRST-URAC 08, University of Moulay Ismail, Physics Department, Faculty of Sciences, B.P. 11201 Meknes (Morocco); Max-Planck-Institut für Physik Complexer Systeme, Nöthnitzer Str. 38 D-01187 Dresden (Germany); Ahuja, R. [Condensed Matter Theory Group, Department of Physics and Astronomy, Uppsala University, 75120 Uppsala (Sweden); Dujardin, F. [Laboratoire de Chimie et Physique des Milieux Complexes (LCPMC), Institut de Chimie, Physique et Matériaux (ICPM), 1 Bd. Arago, 57070 Metz (France)

2013-06-15

In this paper, the phase diagrams of diluted Ising nanowire consisting of core and surface shell coupling by J{sub cs} exchange interaction are studied using the effective field theory with a probability distribution technique, in the presence of transverse fields in the core and in the surface shell. We find a number of characteristic phenomena. In particular, the effect of concentration c of magnetic atoms, the exchange interaction core/shell, the exchange in surface and the transverse fields in core and in surface shell of phase diagrams are investigated. - Highlights: ► We use the EFT to investigate the phase diagrams of Ising transverse nanowire. ► Ferrimagnetic and ferromagnetic cases are investigated. ► The effects of the dilution and the transverse fields in core and shell are studied. ► Behavior of the transition temperature with the exchange interaction is given.

Human Behaviour Analysis of Barrier Deviations Using a Benefit-Cost-Deficit Model

Directory of Open Access Journals (Sweden)

Philippe Polet

2009-01-01

Full Text Available A Benefit-Cost-Deficit (BCD model is proposed for analyzing such intentional human errors as barrier removal, the deliberate nonrespect of the rules and instructions governing use of a given system. The proposed BCD model attempts to explain and predict barrier removal in terms of the benefits, costs, and potential deficits associated with this human behaviour. The results of an experimental study conducted on a railway simulator (TRANSPAL are used to illustrate the advantages of the BCD model. In this study, human operators were faced with barriers that they could choose to deactivate, or not. Their decisions were analyzed in an attempt to explain and predict their choices. The analysis highlights that operators make their decisions using a balance between several criteria. Though barriers are safety-related elements, the decision to remove them is not guided only by the safety criterion; it is also motivated by such criteria as productivity, workload, and quality. Results of prediction supported by the BCD demonstrate the predictability of barrier violation

The Diagram as Story: Unfolding the Event-Structure of the Mathematical Diagram

Science.gov (United States)

de Freitas, Elizabeth

2012-01-01

This paper explores the role of narrative in decoding diagrams. I focus on two fundamental facets of narrative: (1) the recounting of causally related sequences of events, and (2) the positioning of the narrator through point-of-view and voice. In the first two sections of the paper I discuss philosophical and semiotic frameworks for making sense…

Community pharmacists' perceptions of barriers to communication with migrants.

Science.gov (United States)

Cleland, Jennifer A; Watson, Margaret C; Walker, Leighton; Denison, Alan; Vanes, Neil; Moffat, Mandy

2012-06-01

Effective communication by pharmacists is essential to ensure patient safety in terms of provision and use of medications by patients. Global migration trends mean community pharmacists increasingly encounter patients with a variety of first languages. The aim of this study was to explore community pharmacists' perceptions of communication barriers during the provision of care to A8 (nationals from central/Eastern European states) migrants. A qualitative face-to-face interview study of purposively sampled community pharmacists, North East Scotland. Participants (n = 14) identified a number of barriers to providing optimal care to A8 migrants including: communication (information gathering and giving); confidentiality when using family/friends as translators; the impact of patient healthcare expectations on communication and the length of the consultation; and frustration with the process of the consultation. Several barriers were specific to A8 migrants but most seemed pertinent to any group with limited English proficiency and reflect those found in studies of healthcare professionals caring for more traditional UK migrant populations. Further research is needed using objective outcome measures, such as consultation recordings, to measure the impact of these perceived barriers on pharmacist-patient consultations. Language and cultural barriers impact on the quality of pharmacist-patient communication and thus may have patient safety and pharmacist training implications. © 2011 The Authors. IJPP © 2011 Royal Pharmaceutical Society.

High tension generator for corona barrier discharge

International Nuclear Information System (INIS)

Baltag, O.; Costandache, D.; Gheorghiu, M.; Paraschivescu, A.; Popa, G.

2001-01-01

Different types of high-voltage generators are in use for the study of low pressure (or atmospheric) discharges. Mostly used are the Tesla coils generators or the power generators working in linear or switching regime. The Tesla coils generators have the advantage of a simple bloc diagram. In exchange, they have a number of short-comings, such as: the difficulty in modifying the frequency of the high voltage pulses, generation of a high voltage and frequency pulse train, the amplitude is not constant.This paper presents a high-voltage generator meant to be used in the study of the dielectric barrier discharges (DBD). The bloc diagram is presented. Performances obtained are as follows: - Generated frequency: 10 Hz - 100 Hz, 100 Hz - 1 KHz, 1 KHz - 10 KHz; - High voltage pulses control: a single pulse from an internal or external generator; - Synchronization with the oscilloscope, variable delay: 5 μs - 0.1 s; - Output voltage: variable both smoothly and in steps: 1 kV -15 kV; - High voltage polarity: mono and bipolar; - Output power during the continuous duty: 300 VA (maximum 600 VA for a short time); - Pulse energy: 0.23 J; - Pulse duration: 4 μs - 50 μs

Safety performance monitoring of autonomous marine systems

International Nuclear Information System (INIS)

Thieme, Christoph A.; Utne, Ingrid B.

2017-01-01

The marine environment is vast, harsh, and challenging. Unanticipated faults and events might lead to loss of vessels, transported goods, collected scientific data, and business reputation. Hence, systems have to be in place that monitor the safety performance of operation and indicate if it drifts into an intolerable safety level. This article proposes a process for developing safety indicators for the operation of autonomous marine systems (AMS). The condition of safety barriers and resilience engineering form the basis for the development of safety indicators, synthesizing and further adjusting the dual assurance and the resilience based early warning indicator (REWI) approaches. The article locates the process for developing safety indicators in the system life cycle emphasizing a timely implementation of the safety indicators. The resulting safety indicators reflect safety in AMS operation and can assist in planning of operations, in daily operational decision-making, and identification of improvements. Operation of an autonomous underwater vehicle (AUV) exemplifies the process for developing safety indicators and their implementation. The case study shows that the proposed process leads to a comprehensive set of safety indicators. It is expected that application of the resulting safety indicators consequently will contribute to safer operation of current and future AMS. - Highlights: • Process for developing safety indicators for autonomous marine systems. • Safety indicators based on safety barriers and resilience thinking. • Location of the development process in the system lifecycle. • Case study on AUV demonstrating applicability of the process.

Random matrix models for phase diagrams

International Nuclear Information System (INIS)

Vanderheyden, B; Jackson, A D

2011-01-01

We describe a random matrix approach that can provide generic and readily soluble mean-field descriptions of the phase diagram for a variety of systems ranging from quantum chromodynamics to high-T c materials. Instead of working from specific models, phase diagrams are constructed by averaging over the ensemble of theories that possesses the relevant symmetries of the problem. Although approximate in nature, this approach has a number of advantages. First, it can be useful in distinguishing generic features from model-dependent details. Second, it can help in understanding the 'minimal' number of symmetry constraints required to reproduce specific phase structures. Third, the robustness of predictions can be checked with respect to variations in the detailed description of the interactions. Finally, near critical points, random matrix models bear strong similarities to Ginsburg-Landau theories with the advantage of additional constraints inherited from the symmetries of the underlying interaction. These constraints can be helpful in ruling out certain topologies in the phase diagram. In this Key Issues Review, we illustrate the basic structure of random matrix models, discuss their strengths and weaknesses, and consider the kinds of system to which they can be applied.

Colour-magnitude diagram of NGC 5053

Energy Technology Data Exchange (ETDEWEB)

Walker, M F; Pike, C D [California Univ., Santa Cruz (USA). Lick Observatory; McGee, J D

1976-06-01

The colour-magnitude diagram of NGC 5053 has been derived to V = 21.1 from photographic and electronographic observations. The electronographic observations were obtained with an experimental Spectracon image-converter, having photocathode and exit window dimensions of 20 x 30 mm, mounted at the prime-focus of the 120-in. Lick reflector. The photographic observations were obtained with the 20-in. Carnegie astrograph and the 36-in. Crossley reflector. The colour-magnitude diagram resembles that of M92, with the difference that a red horizontal branch is more pronounced than the asymptotic branch in NGC 5053. The topology of the horizontal branch is that of clusters with an intermediate metal content and is thus at variance with the mean period of the RR Lyr stars and the unreddened colour of the subgiant branch read at the magnitude level of the horizontal branch, both of which would indicate an extremely low metal content. If comparison of the colour-magnitude diagrams of NGC 5053 and M92 is valid, then the reddening of NGC 5053 is Esub(B-V) = 0.02 and the apparent distance modulus is m-M = 16.08 +- 0.08.

Safety of VVER-440 reactors

CERN Document Server

Slugen, Vladimir

2011-01-01

Safety of VVER-440 Reactors endeavours to promote an increase in the safety of VVER-440 nuclear reactors via the improvement of fission products limitation systems and the implementation of special non-destructive spectroscopic methods for materials testing. All theoretical and experimental studies performed the by author over the last 25 years have been undertaken with the aim of improving VVER-440 defence in depth, which is one of the most important principle for ensuring safety in nuclear power plants. Safety of VVER-440 Reactors is focused on the barrier system through which the safety pri

Reactome diagram viewer: data structures and strategies to boost performance.

Science.gov (United States)

Fabregat, Antonio; Sidiropoulos, Konstantinos; Viteri, Guilherme; Marin-Garcia, Pablo; Ping, Peipei; Stein, Lincoln; D'Eustachio, Peter; Hermjakob, Henning

2018-04-01

Reactome is a free, open-source, open-data, curated and peer-reviewed knowledgebase of biomolecular pathways. For web-based pathway visualization, Reactome uses a custom pathway diagram viewer that has been evolved over the past years. Here, we present comprehensive enhancements in usability and performance based on extensive usability testing sessions and technology developments, aiming to optimize the viewer towards the needs of the community. The pathway diagram viewer version 3 achieves consistently better performance, loading and rendering of 97% of the diagrams in Reactome in less than 1 s. Combining the multi-layer html5 canvas strategy with a space partitioning data structure minimizes CPU workload, enabling the introduction of new features that further enhance user experience. Through the use of highly optimized data structures and algorithms, Reactome has boosted the performance and usability of the new pathway diagram viewer, providing a robust, scalable and easy-to-integrate solution to pathway visualization. As graph-based visualization of complex data is a frequent challenge in bioinformatics, many of the individual strategies presented here are applicable to a wide range of web-based bioinformatics resources. Reactome is available online at: https://reactome.org. The diagram viewer is part of the Reactome pathway browser (https://reactome.org/PathwayBrowser/) and also available as a stand-alone widget at: https://reactome.org/dev/diagram/. The source code is freely available at: https://github.com/reactome-pwp/diagram. fabregat@ebi.ac.uk or hhe@ebi.ac.uk. Supplementary data are available at Bioinformatics online.

Limits of Voronoi Diagrams

NARCIS (Netherlands)

Lindenbergh, R.C.

2002-01-01

The classic Voronoi diagram of a configuration of distinct points in the plane associates to each point that part of the plane that is closer to the point than to any other point in the configuration. In this thesis we no longer require all points to be distinct. After the introduction in

Mediating role of critical thinking disposition in the relationship between perceived barriers to research use and evidence-based practice.

Science.gov (United States)

Kim, Sun-Ae; Song, Youngshin; Sim, Hee-Sook; Ahn, Eun-Kyong; Kim, Jung-Hee

2015-01-01

Despite the importance of critical thinking in clinical and educational settings, little is known about its role in evidence-based practice (EBP). This study examined whether critical thinking disposition (CTD) mediates the relationship between perceived barriers to research use and EBP in clinical nurses (N=409). A path diagram using structural equation modeling was used to estimate the direct and indirect effects of perceived barriers to research use on EBP, controlling for CTD as a mediator. CTD partially mediated the relationship between perceived barriers to research use and EBP. Furthermore, the hypothesized mediation model demonstrated an appropriate fit to the data. Individual and organizational efforts are needed to help nurses further improve their critical thinking skills. CTD is important as research barriers to engage effectively in EBP. Without the skills to evaluate evidence carefully, research utilization may be compromised.

Unified Phase Diagram for Iron-Based Superconductors.

Science.gov (United States)

Gu, Yanhong; Liu, Zhaoyu; Xie, Tao; Zhang, Wenliang; Gong, Dongliang; Hu, Ding; Ma, Xiaoyan; Li, Chunhong; Zhao, Lingxiao; Lin, Lifang; Xu, Zhuang; Tan, Guotai; Chen, Genfu; Meng, Zi Yang; Yang, Yi-Feng; Luo, Huiqian; Li, Shiliang

2017-10-13

High-temperature superconductivity is closely adjacent to a long-range antiferromagnet, which is called a parent compound. In cuprates, all parent compounds are alike and carrier doping leads to superconductivity, so a unified phase diagram can be drawn. However, the properties of parent compounds for iron-based superconductors show significant diversity and both carrier and isovalent dopings can cause superconductivity, which casts doubt on the idea that there exists a unified phase diagram for them. Here we show that the ordered moments in a variety of iron pnictides are inversely proportional to the effective Curie constants of their nematic susceptibility. This unexpected scaling behavior suggests that the magnetic ground states of iron pnictides can be achieved by tuning the strength of nematic fluctuations. Therefore, a unified phase diagram can be established where superconductivity emerges from a hypothetical parent compound with a large ordered moment but weak nematic fluctuations, which suggests that iron-based superconductors are strongly correlated electron systems.

Unified Phase Diagram for Iron-Based Superconductors

Science.gov (United States)

Gu, Yanhong; Liu, Zhaoyu; Xie, Tao; Zhang, Wenliang; Gong, Dongliang; Hu, Ding; Ma, Xiaoyan; Li, Chunhong; Zhao, Lingxiao; Lin, Lifang; Xu, Zhuang; Tan, Guotai; Chen, Genfu; Meng, Zi Yang; Yang, Yi-feng; Luo, Huiqian; Li, Shiliang

2017-10-01

High-temperature superconductivity is closely adjacent to a long-range antiferromagnet, which is called a parent compound. In cuprates, all parent compounds are alike and carrier doping leads to superconductivity, so a unified phase diagram can be drawn. However, the properties of parent compounds for iron-based superconductors show significant diversity and both carrier and isovalent dopings can cause superconductivity, which casts doubt on the idea that there exists a unified phase diagram for them. Here we show that the ordered moments in a variety of iron pnictides are inversely proportional to the effective Curie constants of their nematic susceptibility. This unexpected scaling behavior suggests that the magnetic ground states of iron pnictides can be achieved by tuning the strength of nematic fluctuations. Therefore, a unified phase diagram can be established where superconductivity emerges from a hypothetical parent compound with a large ordered moment but weak nematic fluctuations, which suggests that iron-based superconductors are strongly correlated electron systems.

Trench Safety–Using a Qualitative Approach to Understand Barriers and Develop Strategies to Improve Trenching Practices

Science.gov (United States)

FLYNN, MICHAEL A.; SAMPSON, JULIE M.

2015-01-01

Despite efforts to ensure workplace safety and health, injuries and fatalities related to trenching and excavation remain alarmingly high in the construction industry. Because properly installed trenching protective systems can potentially reduce the significant number of trenching fatalities, there is clearly a need to identify the barriers to the use of these systems and to develop strategies to ensure these systems are utilized consistently. The current study reports on the results of focus groups with construction workers and safety management personnel to better understand these barriers and to identify solutions. The results suggest several factors, from poor planning to pressures from experienced workers and supervisors, which present barriers to safe trenching practices. Based on the results, it is recommended that safety trainings incorporate unique messages for new workers, experienced workers and management in an effort to motivate each group to work safely as well as provide them with solutions to overcome the identified barriers. PMID:26550006

Exploring Facilitators and Barriers to Initiation and Completion of the Human Papillomavirus (HPV) Vaccine Series among Parents of Girls in a Safety Net System.

Science.gov (United States)

O'Leary, Sean T; Lockhart, Steven; Barnard, Juliana; Furniss, Anna; Dickinson, Miriam; Dempsey, Amanda F; Stokley, Shannon; Federico, Steven; Bronsert, Michael; Kempe, Allison

2018-01-23

Objective: To assess, among parents of predominantly minority, low-income adolescent girls who had either not initiated (NI) or not completed (NC) the HPV vaccine series, attitudes and other factors important in promoting the series, and whether attitudes differed by language preference. Design/Methods: From August 2013-October 2013, we conducted a mail survey among parents of girls aged 12-15 years randomly selected from administrative data in a Denver safety net system; 400 parents from each group (NI and NC) were targeted. Surveys were in English or Spanish. The response rate was 37% (244/660; 140 moved or gone elsewhere; 66% English-speaking, 34% Spanish-speaking). Safety attitudes of NIs and NCs differed, with 40% NIs vs. 14% NC's reporting they thought HPV vaccine was unsafe ( p HPV vaccine before, but now I am" (English-speaking, 23%, Spanish-speaking, 50%). Items rated as very important among NIs in the decision regarding vaccination included: more information about safety (74%), more information saying it prevents cancer (70%), and if they knew HPV was spread mainly by sexual contact (61%). Conclusions : Safety concerns, being unaware of the need for multiple doses, and low perceived risk of infection remain significant barriers to HPV vaccination for at-risk adolescents. Some parents' safety concerns do not appear until initial vaccination.

Causal diagrams in systems epidemiology

Directory of Open Access Journals (Sweden)

Joffe Michael

2012-03-01

Full Text Available Abstract Methods of diagrammatic modelling have been greatly developed in the past two decades. Outside the context of infectious diseases, systematic use of diagrams in epidemiology has been mainly confined to the analysis of a single link: that between a disease outcome and its proximal determinant(s. Transmitted causes ("causes of causes" tend not to be systematically analysed. The infectious disease epidemiology modelling tradition models the human population in its environment, typically with the exposure-health relationship and the determinants of exposure being considered at individual and group/ecological levels, respectively. Some properties of the resulting systems are quite general, and are seen in unrelated contexts such as biochemical pathways. Confining analysis to a single link misses the opportunity to discover such properties. The structure of a causal diagram is derived from knowledge about how the world works, as well as from statistical evidence. A single diagram can be used to characterise a whole research area, not just a single analysis - although this depends on the degree of consistency of the causal relationships between different populations - and can therefore be used to integrate multiple datasets. Additional advantages of system-wide models include: the use of instrumental variables - now emerging as an important technique in epidemiology in the context of mendelian randomisation, but under-used in the exploitation of "natural experiments"; the explicit use of change models, which have advantages with respect to inferring causation; and in the detection and elucidation of feedback.

Causal diagrams in systems epidemiology.

Science.gov (United States)

Joffe, Michael; Gambhir, Manoj; Chadeau-Hyam, Marc; Vineis, Paolo

2012-03-19

Methods of diagrammatic modelling have been greatly developed in the past two decades. Outside the context of infectious diseases, systematic use of diagrams in epidemiology has been mainly confined to the analysis of a single link: that between a disease outcome and its proximal determinant(s). Transmitted causes ("causes of causes") tend not to be systematically analysed.The infectious disease epidemiology modelling tradition models the human population in its environment, typically with the exposure-health relationship and the determinants of exposure being considered at individual and group/ecological levels, respectively. Some properties of the resulting systems are quite general, and are seen in unrelated contexts such as biochemical pathways. Confining analysis to a single link misses the opportunity to discover such properties.The structure of a causal diagram is derived from knowledge about how the world works, as well as from statistical evidence. A single diagram can be used to characterise a whole research area, not just a single analysis - although this depends on the degree of consistency of the causal relationships between different populations - and can therefore be used to integrate multiple datasets.Additional advantages of system-wide models include: the use of instrumental variables - now emerging as an important technique in epidemiology in the context of mendelian randomisation, but under-used in the exploitation of "natural experiments"; the explicit use of change models, which have advantages with respect to inferring causation; and in the detection and elucidation of feedback.

The laser Megajoule facility personnel security and safety interlocks

International Nuclear Information System (INIS)

Chapuis, J.C.; Arnoul, J.P.; Hurst, A.; Manson, M.

2012-01-01

The LMJ (Laser Megajoule) is designed to deliver about 1.4 MJ of 0.35 μm light to targets for high energy density physics experiments. Such an installation entails specific hazards related to the presence of intense laser beams, and high voltage power laser amplifiers. Furthermore, the thermonuclear fusion reactions induced by the experiment also produce different radiations and neutrons burst, and also activate various materials in the chamber environment. All these hazards could be lethal. The SSP (Personnel Safety System) was designed to prevent accidents and protect personnel working in the LMJ. To satisfy at the lowest cost the requirements of safety regulations and those of the operation management, the choice was made to implement a functional architecture built around two independent technological barriers when required by the risk level. Each technical barrier is composed of two subsets, one dedicated to hazard sources management, and the other one dedicated to worker presence management. The two completely independent barriers, even at the sensor or actuator level, are designed with different technologies adapted to the required Safety Integrity Level. The combination of these 2 barriers is equivalent to a unique barrier with a rate of dangerous failure of about 10 -6 per year

Calculation of Energy Diagram of Asymmetric Graded-Band-Gap Semiconductor Superlattices.

Science.gov (United States)

Monastyrskii, Liubomyr S; Sokolovskii, Bogdan S; Alekseichyk, Mariya P

2017-12-01

The paper theoretically investigates the peculiarities of energy diagram of asymmetric graded-band-gap superlattices with linear coordinate dependences of band gap and electron affinity. For calculating the energy diagram of asymmetric graded-band-gap superlattices, linearized Poisson's equation has been solved for the two layers forming a period of the superlattice. The obtained coordinate dependences of edges of the conduction and valence bands demonstrate substantial transformation of the shape of the energy diagram at changing the period of the lattice and the ratio of width of the adjacent layers. The most marked changes in the energy diagram take place when the period of lattice is comparable with the Debye screening length. In the case when the lattice period is much smaller that the Debye screening length, the energy diagram has the shape of a sawtooth-like pattern.

RNA secondary structure diagrams for very large molecules: RNAfdl

DEFF Research Database (Denmark)

Hecker, Nikolai; Wiegels, Tim; Torda, Andrew E.

2013-01-01

There are many programs that can read the secondary structure of an RNA molecule and draw a diagram, but hardly any that can cope with 10 3 bases. RNAfdl is slow but capable of producing intersection-free diagrams for ribosome-sized structures, has a graphical user interface for adjustments...

Automated Methodologies for the Design of Flow Diagrams for Development and Maintenance Activities

Science.gov (United States)

Shivanand M., Handigund; Shweta, Bhat

The Software Requirements Specification (SRS) of the organization is a text document prepared by strategic management incorporating the requirements of the organization. These requirements of ongoing business/ project development process involve the software tools, the hardware devices, the manual procedures, the application programs and the communication commands. These components are appropriately ordered for achieving the mission of the concerned process both in the project development and the ongoing business processes, in different flow diagrams viz. activity chart, workflow diagram, activity diagram, component diagram and deployment diagram. This paper proposes two generic, automatic methodologies for the design of various flow diagrams of (i) project development activities, (ii) ongoing business process. The methodologies also resolve the ensuing deadlocks in the flow diagrams and determine the critical paths for the activity chart. Though both methodologies are independent, each complements other in authenticating its correctness and completeness.

The Fishbone diagram to identify, systematize and analyze the sources of general purpose technologies

OpenAIRE

COCCIA, Mario

2017-01-01

Abstract. This study suggests the fishbone diagram for technological analysis. Fishbone diagram (also called Ishikawa diagrams or cause-and-effect diagrams) is a graphical technique to show the several causes of a specific event or phenomenon. In particular, a fishbone diagram (the shape is similar to a fish skeleton) is a common tool used for a cause and effect analysis to identify a complex interplay of causes for a specific problem or event. The fishbone diagram can be a comprehensive theo...

Quantum MHV Diagrams

OpenAIRE

Brandhuber, Andreas; Travaglini, Gabriele

2006-01-01

Over the past two years, the use of on-shell techniques has deepened our understanding of the S-matrix of gauge theories and led to the calculation of many new scattering amplitudes. In these notes we review a particular on-shell method developed recently, the quantum MHV diagrams, and discuss applications to one-loop amplitudes. Furthermore, we briefly discuss the application of D-dimensional generalised unitarity to the calculation of scattering amplitudes in non-supersymmetric Yang-Mills.

Impact of removing mucosal barrier injury laboratory-confirmed bloodstream infections from central line-associated bloodstream infection rates in the National Healthcare Safety Network, 2014.

Science.gov (United States)

See, Isaac; Soe, Minn M; Epstein, Lauren; Edwards, Jonathan R; Magill, Shelley S; Thompson, Nicola D

2017-03-01

Central line-associated bloodstream infection (CLABSI) event data reported to the National Healthcare Safety Network from 2014, the first year of required use of the mucosal barrier injury laboratory-confirmed bloodstream infection (MBI-LCBI) definition, were analyzed to assess the impact of removing MBI-LCBI events from CLABSI rates. CLABSI rates decreased significantly in some location types after removing MBI-LCBI events, and MBI-LCBI events will be removed from publicly reported CLABSI rates. Published by Elsevier Inc.

A new safety concept for geological disposal in Japan (II) - 59357

International Nuclear Information System (INIS)

Kitayama, Kazumi

2012-01-01

This paper provides further discussion of a new defence-in-depth safety concept that was presented at ICEM09[1]. The basic idea is that it is rational to assume that the performance of passive engineered barriers with suitably chosen characteristics and the natural barrier will maintain their safety functions for a sufficiently long time due to geochemical buffering occurring deep underground, The approach can be used to enhance and embed public understanding of the long-term safety of geological disposal. This paper summarizes the logic of the approach focusing on the following topics, which are the basic themes of the new safety concept. 1. Applicability of the defence-in-depth concept to the geological disposal of radioactive waste; 2. Natural Analogue approach to explaining the long-term behaviour of the barriers; and 3. Approach for the Social Dialogue with stakeholder, which is the most important issue for site selection. (authors)

Safety of nuclear installations

International Nuclear Information System (INIS)

Esteves, R.G.

1987-01-01

The safety philosophy of a PWR type reactor distinguishing three levels of safety, is presented. At the first level, the concept of reactivity defining coefficients which measure the reactivity variation is introduced. At the second level, the reactor protection system establishing the design criteria to assure the high reliability, is defined. At the third level, the protection barriers to contain the consequences of accident evolution, are defined. (M.C.K.) [pt

Heuristic Diagrams as a Tool to Teach History of Science

Science.gov (United States)

Chamizo, José A.

2012-05-01

The graphic organizer called here heuristic diagram as an improvement of Gowin's Vee heuristic is proposed as a tool to teach history of science. Heuristic diagrams have the purpose of helping students (or teachers, or researchers) to understand their own research considering that asks and problem-solving are central to scientific activity. The left side originally related in Gowin's Vee with philosophies, theories, models, laws or regularities now agrees with Toulmin's concepts (language, models as representation techniques and application procedures). Mexican science teachers without experience in science education research used the heuristic diagram to learn about the history of chemistry considering also in the left side two different historical times: past and present. Through a semantic differential scale teachers' attitude to the heuristic diagram was evaluated and its usefulness was demonstrated.

Bayesian Networks and Influence Diagrams

DEFF Research Database (Denmark)

Kjærulff, Uffe Bro; Madsen, Anders Læsø

Bayesian Networks and Influence Diagrams: A Guide to Construction and Analysis, Second Edition, provides a comprehensive guide for practitioners who wish to understand, construct, and analyze intelligent systems for decision support based on probabilistic networks. This new edition contains six new...

INFRARED COLOR-COLOR DIAGRAMS FOR AGB STARS

Directory of Open Access Journals (Sweden)

Kyung-Won Suh

2007-09-01

Full Text Available We present infrared color-color diagrams of AGB stars from the observations at near and mid infrared bands. We compile the observations for hundreds of OH/IR stars and carbon stars using the data from the Midcourse Space Experiment (MSX, the two micron sky survey (2MASS, and the IRAS point source catalog (PSC. We compare the observations with the theoretical evolutionary tracks of AGB stars. From the new observational data base and the theoretical evolution tracks, we discuss the meaning of the infrared color-color diagrams at different wavelengths.

Examining competing hypotheses for the effects of diagrams on recall for text.

Science.gov (United States)

Ortegren, Francesca R; Serra, Michael J; England, Benjamin D

2015-01-01

Supplementing text-based learning materials with diagrams typically increases students' free recall and cued recall of the presented information. In the present experiments, we examined competing hypotheses for why this occurs. More specifically, although diagrams are visual, they also serve to repeat information from the text they accompany. Both visual presentation and repetition are known to aid students' recall of information. To examine to what extent diagrams aid recall because they are visual or repetitive (or both), we had college students in two experiments (n = 320) read a science text about how lightning storms develop before completing free-recall and cued-recall tests over the presented information. Between groups, we manipulated the format and repetition of target pieces of information in the study materials using a 2 (visual presentation of target information: diagrams present vs. diagrams absent) × 2 (repetition of target information: present vs. absent) between-participants factorial design. Repetition increased both the free recall and cued recall of target information, and this occurred regardless of whether that repetition was in the form of text or a diagram. In contrast, the visual presentation of information never aided free recall. Furthermore, visual presentation alone did not significantly aid cued recall when participants studied the materials once before the test (Experiment 1) but did when they studied the materials twice (Experiment 2). Taken together, the results of the present experiments demonstrate the important role of repetition (i.e., that diagrams repeat information from the text) over the visual nature of diagrams in producing the benefits of diagrams for recall.

On Hardy's paradox, weak measurements, and multitasking diagrams

International Nuclear Information System (INIS)

Meglicki, Zdzislaw

2011-01-01

We discuss Hardy's paradox and weak measurements by using multitasking diagrams, which are introduced to illustrate the progress of quantum probabilities through the double interferometer system. We explain how Hardy's paradox is avoided and elaborate on the outcome of weak measurements in this context. -- Highlights: → Hardy's paradox explained and eliminated. → Weak measurements: what is really measured? → Multitasking diagrams: introduced and used to discuss quantum mechanical processes.

On the phase diagram of non-spherical nanoparticles

CERN Document Server

Wautelet, M; Hecq, M

2003-01-01

The phase diagram of nanoparticles is known to be a function of their size. In the literature, this is generally demonstrated for cases where their shape is spherical. Here, it is shown theoretically that the phase diagram of non-spherical particles may be calculated from the spherical case, at the same surface area/volume ratio, both with and without surface segregation, provided the surface tension is considered to be isotropic.

Bifurcation diagram features of a dc-dc converter under current-mode control

International Nuclear Information System (INIS)

Ruzbehani, Mohsen; Zhou Luowei; Wang Mingyu

2006-01-01

A common tool for analysis of the systems dynamics when the system has chaotic behaviour is the bifurcation diagram. In this paper, the bifurcation diagram of an ideal model of a dc-dc converter under current-mode control is analysed. Algebraic relations that give the critical points locations and describe the pattern of the bifurcation diagram are derived. It is shown that these simple algebraic and geometrical relations are responsible for the complex pattern of the bifurcation diagrams in such circuits. More explanation about the previously observed properties and introduction of some new ones are exposited. In addition, a new three-dimensional bifurcation diagram that can give better imagination of the parameters role is introduced

Differential Rollover Risk in Vehicle-to-Traffic Barrier Collisions

Science.gov (United States)

Gabauer, Douglas J.; Gabler, Hampton C.

2009-01-01

In the roadside safety community, there has been debate over the influence of vehicle and barrier type on rollover rates in traffic barrier crashes. This study investigated rollover rates between sport utility vehicles (SUVs), pickup trucks, and cars in vehicle-traffic barrier crashes and has examined the effect of barrier type on rollover risk for concrete barrier and metal barrier impacts. The analysis included 955 barrier impact cases that were selected from 11-years of in-depth crash data available through the National Automotive Sampling System (NASS) / Crashworthiness Data System (CDS). In real world tow-away level longitudinal barrier collisions, the most important predictors of vehicle rollover were found to be vehicle type and whether the vehicle was tracking prior to barrier impact. Based on binary logistic regression, SUVs were found to have 8 times the risk of rollover as cars in barrier impacts. Although pickups were found to have an increased risk of rollover compared to cars, the risk was not as pronounced as that found for SUVs. This finding has direct implications for the full scale crash testing of longitudinal barriers as the testing procedures have been predicated on the assumption that the pickup truck provides a critical or worst case impact scenario. In towaway crashes, our study does not support the notion that concrete barriers have a higher risk of vehicle rollover than metal beam barriers. PMID:20184839

Work zone safety : physical and behavioral barriers in accident prevention.

Science.gov (United States)

2014-05-01

This report discusses the usefulness of creating a work zone traffic safety culture as a methodology to improve the overall : safety of both work zone personnel and the traveling public in Missouri. As part of this research, the existing MoDOT : w : ...

DIAGRAM SOLVE THE USE OF SIMULINK BLOCK DIAGRAM TO SOLVE MATHEMA THEMATICAL CONTROL EQU MATHEMATICAL MODELS AND CONTROL EQUATIONS

Directory of Open Access Journals (Sweden)

N.M. Ghasem

2003-12-01

Full Text Available In this paper, the simulink block diagram is used to solve a model consists of a set of ordinary differential and algebraic equations to control the temperature inside a simple stirred tank heater. The flexibility of simulink block diagram gives students a better understanding of the control systems. The simulink also allows solution of mathematical models and easy visualization of the system variables. A polyethylene fluidized bed reactor is considered as an industrial example and the effect of the Proportional, Integral and Derivative control policy is presented for comparison.

Transport barriers in bootstrap-driven tokamaks

Science.gov (United States)

Staebler, G. M.; Garofalo, A. M.; Pan, C.; McClenaghan, J.; Van Zeeland, M. A.; Lao, L. L.

2018-05-01

Experiments have demonstrated improved energy confinement due to the spontaneous formation of an internal transport barrier in high bootstrap fraction discharges. Gyrokinetic analysis, and quasilinear predictive modeling, demonstrates that the observed transport barrier is caused by the suppression of turbulence primarily from the large Shafranov shift. It is shown that the Shafranov shift can produce a bifurcation to improved confinement in regions of positive magnetic shear or a continuous reduction in transport for weak or negative magnetic shear. Operation at high safety factor lowers the pressure gradient threshold for the Shafranov shift-driven barrier formation. Two self-organized states of the internal and edge transport barrier are observed. It is shown that these two states are controlled by the interaction of the bootstrap current with magnetic shear, and the kinetic ballooning mode instability boundary. Election scale energy transport is predicted to be dominant in the inner 60% of the profile. Evidence is presented that energetic particle-driven instabilities could be playing a role in the thermal energy transport in this region.

Electroweak penguin diagrams and two-body B decays

International Nuclear Information System (INIS)

Gronau, M.; Hernandez, O.F.; London, D.; Rosner, J.L.

1995-01-01

We discuss the role of electroweak penguin diagrams in B decays to two light pseudoscalar mesons. We confirm that the extraction of the weak phase α through the isospin analysis involving B→ππ decays is largely unaffected by such operators. However, the methods proposed to obtain weak and strong phases by relating B→ππ, B→πK, and B→K bar K decays through flavor SU(3) will be invalidated if eletroweak penguin diagrams are large. We show that, although the introduction of electroweak penguin contributions introduces no new amplitudes of flavor SU(3), there are a number of ways to experimentally measure the size of such effects. Finally, using SU(3) amplitude relations we present a new way of measuring the weak angle γ which holds even in the presence of electroweak penguin diagrams

Anytime decision making based on unconstrained influence diagrams

DEFF Research Database (Denmark)

Luque, Manuel; Nielsen, Thomas Dyhre; Jensen, Finn Verner

2016-01-01

. This paper addresses this problem by proposing an anytime algorithm that at any time provides a qualified recommendation for the first decisions of the problem. The algorithm performs a heuristic-based search in a decision tree representation of the problem. We provide a framework for analyzing......Unconstrained influence diagrams extend the language of influence diagrams to cope with decision problems in which the order of the decisions is unspecified. Thus, when solving an unconstrained influence diagram we not only look for an optimal policy for each decision, but also for a so-called step......-policy specifying the next decision given the observations made so far. However, due to the complexity of the problem, temporal constraints can force the decision maker to act before the solution algorithm has finished, and, in particular, before an optimal policy for the first decision has been computed...

The role of perceived barriers and objectively measured physical activity in adults aged 65-100.

Science.gov (United States)

Gellert, Paul; Witham, Miles D; Crombie, Iain K; Donnan, Peter T; McMurdo, Marion E T; Sniehotta, Falko F

2015-05-01

to test the predictive utility of perceived barriers to objectively measured physical activity levels in a stratified sample of older adults when accounting for social-cognitive determinants proposed by the Theory of Planned Behaviour (TPB), and economic and demographic factors. data were analysed from the Physical Activity Cohort Scotland survey, a representative and stratified (65-80 and 80+ years; deprived and affluent) sample of 584 community-dwelling older people, resident in Tayside, Scotland. Physical activity was measured objectively by accelerometry. perceived barriers clustered around the areas of poor health, lack of interest, lack of safety and lack of access. Perceived poor health and lack of interest, but not lack of access or concerns about personal safety, predicted physical activity after controlling for demographic, economic and TPB variables. perceived person-related barriers (poor health and lack of interest) seem to be more strongly associated with physical activity levels than perceived environmental barriers (safety and access) in a large sample of older adults. Perceived barriers are modifiable and may be a target for future interventions. © The Author 2015. Published by Oxford University Press on behalf of the British Geriatrics Society. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Study on vibration behaviors of engineered barrier system

International Nuclear Information System (INIS)

Mikoshiba, Tadashi; Ogawa, Nobuyuki; Minowa, Chikahiro

1998-01-01

High-level radioactive wastes have been buried underground by packing into a strong sealed container made from carbon steel (over-pack) with buffer material (bentonite). The engineered barrier system constructed with an overpack and buffer materials must be resistant to earthquakes as well as invasion of groundwater for a long period. Therefore, seismic evaluation of barrier system for earthquakes is indispensable especially in Japan to keep its structural safety. Here, the effects of earthquake vibration on the engineered barrier systems were investigated experimentally. Random-wave vibration and practical seismic wave one were loaded for the systems and fundamental data were obtained. For the former vibration the response characteristics of both engineered barrier models constructed with overpack and bentonite were non-linear. For the latter one, the stress in bentonite was increased in proportion to the vibration level. (M.N.)

A new approach to performance assessment of barriers in a repository. Executive summary, draft, technical appendices. Final report

International Nuclear Information System (INIS)

Mueller-Hoeppe, N.; Krone, J.; Niehues, N.; Poehler, M.; Raitz von Frentz, R.; Gauglitz, R.

1999-06-01

Multi-barrier systems are accepted as the basic approach for long term environmental safe isolation of radioactive waste in geological repositories. Assessing the performance of natural and engineered barriers is one of the major difficulties in producing evidence of environmental safety for any radioactive waste disposal facility, due to the enormous complexity of scenarios and uncertainties to be considered. This report outlines a new methodological approach originally developed basically for a repository in salt, but that can be transferred with minor modifications to any other host rock formation. The approach is based on the integration of following elements: (1) Implementation of a simple method and efficient criteria to assess and prove the tightness of geological and engineered barriers; (2) Using the method of Partial Safety Factors in order to assess barrier performance at certain reasonable level of confidence; (3) Integration of a diverse geochemical barrier in the near field of waste emplacement limiting systematically the radiological consequences from any radionuclide release in safety investigations and (4) Risk based approach for the assessment of radionuclide releases. Indicative calculations performed with extremely conservative assumptions allow to exclude any radiological health consequences from a HLW repository in salt to a reference person with a safety level of 99,9999% per year. (orig.)

A Hubble Diagram for Quasars

Directory of Open Access Journals (Sweden)

Susanna Bisogni

2018-01-01

Full Text Available The cosmological model is at present not tested between the redshift of the farthest observed supernovae (z ~ 1.4 and that of the Cosmic Microwave Background (z ~ 1,100. Here we introduce a new method to measure the cosmological parameters: we show that quasars can be used as “standard candles” by employing the non-linear relation between their intrinsic UV and X-ray emission as an absolute distance indicator. We built a sample of ~1,900 quasars with available UV and X-ray observations, and produced a Hubble Diagram up to z ~ 5. The analysis of the quasar Hubble Diagram, when used in combination with supernovae, provides robust constraints on the matter and energy content in the cosmos. The application of this method to forthcoming, larger quasar samples, will also provide tight constraints on the dark energy equation of state and its possible evolution with time.

Impact of Diagrams on Recalling Sequential Elements in Expository Texts.

Science.gov (United States)

Guri-Rozenblit, Sarah

1988-01-01

Examines the instructional effectiveness of abstract diagrams on recall of sequential relations in social science textbooks. Concludes that diagrams assist significantly the recall of sequential relations in a text and decrease significantly the rate of order mistakes. (RS)

A LaTeX graphics routine for drawing Feynman diagrams

International Nuclear Information System (INIS)

Levine, M.J.S.

1990-01-01

FEYNMAN is a LaTeX macropackage which allows the user to construct a versatile range of Feynman diagrams within the text of a document. Diagrams of publication quality may be drawn with relative ease and rapidity. (orig.)

Interactive Land-Use Optimization Using Laguerre Voronoi Diagram with Dynamic Generating Point Allocation

Science.gov (United States)

Chaidee, S.; Pakawanwong, P.; Suppakitpaisarn, V.; Teerasawat, P.

2017-09-01

In this work, we devise an efficient method for the land-use optimization problem based on Laguerre Voronoi diagram. Previous Voronoi diagram-based methods are more efficient and more suitable for interactive design than discrete optimization-based method, but, in many cases, their outputs do not satisfy area constraints. To cope with the problem, we propose a force-directed graph drawing algorithm, which automatically allocates generating points of Voronoi diagram to appropriate positions. Then, we construct a Laguerre Voronoi diagram based on these generating points, use linear programs to adjust each cell, and reconstruct the diagram based on the adjustment. We adopt the proposed method to the practical case study of Chiang Mai University's allocated land for a mixed-use complex. For this case study, compared to other Voronoi diagram-based method, we decrease the land allocation error by 62.557 %. Although our computation time is larger than the previous Voronoi-diagram-based method, it is still suitable for interactive design.

Direct measurements of safety factor profiles with motional Stark effect for KSTAR tokamak discharges with internal transport barriers

Science.gov (United States)

Ko, J.; Chung, J.

2017-06-01

The safety factor profile evolutions have been measured from the plasma discharges with the external current drive mechanism such as the multi-ion-source neutral beam injection for the Korea Superconducting Tokamak Advanced Research (KSTAR) for the first time. This measurement has been possible by the newly installed motional Stark effect (MSE) diagnostic system that utilizes the polarized Balmer-alpha emission from the energetic neutral deuterium atoms induced by the Stark effect under the Lorentz electric field. The 25-channel KSTAR MSE diagnostic is based on the conventional photoelastic modulator approach with the spatial and temporal resolutions less than 2 cm (for the most of the channels except 2 to 3 channels inside the magnetic axis) and about 10 ms, respectively. The strong Faraday rotation imposed on the optical elements in the diagnostic system is calibrated out from a separate and well-designed polarization measurement procedure using an in-vessel reference polarizer during the toroidal-field ramp-up phase before the plasma experiment starts. The combination of the non-inductive current drive during the ramp-up and shape control enables the formation of the internal transport barrier where the pitch angle profiles indicate flat or slightly hollow profiles in the safety factor.

Diagram, Gesture, Agency: Theorizing Embodiment in the Mathematics Classroom

Science.gov (United States)

de Freitas, Elizabeth; Sinclair, Nathalie

2012-01-01

In this paper, we use the work of philosopher Gilles Chatelet to rethink the gesture/diagram relationship and to explore the ways mathematical agency is constituted through it. We argue for a fundamental philosophical shift to better conceptualize the relationship between gesture and diagram, and suggest that such an approach might open up new…

Small-threshold behaviour of two-loop self-energy diagrams: two-particle thresholds

International Nuclear Information System (INIS)

Berends, F.A.; Davydychev, A.I.; Moskovskij Gosudarstvennyj Univ., Moscow; Smirnov, V.A.; Moskovskij Gosudarstvennyj Univ., Moscow

1996-01-01

The behaviour of two-loop two-point diagrams at non-zero thresholds corresponding to two-particle cuts is analyzed. The masses involved in a cut and the external momentum are assumed to be small as compared to some of the other masses of the diagram. By employing general formulae of asymptotic expansions of Feynman diagrams in momenta and masses, we construct an algorithm to derive analytic approximations to the diagrams. In such a way, we calculate several first coefficients of the expansion. Since no conditions on relative values of the small masses and the external momentum are imposed, the threshold irregularities are described analytically. Numerical examples, using diagrams occurring in the standard model, illustrate the convergence of the expansion below the first large threshold. (orig.)

Phase shifts of the paired wings of butterfly diagrams

International Nuclear Information System (INIS)

Li Kejun; Liang Hongfei; Feng Wen

2010-01-01

Sunspot groups observed by the Royal Greenwich Observatory/US Air Force/NOAA from 1874 May to 2008 November and the Carte Synoptique solar filaments from 1919 March to 1989 December are used to investigate the relative phase shift of the paired wings of butterfly diagrams of sunspot and filament activities. Latitudinal migration of sunspot groups (or filaments) does asynchronously occur in the northern and southern hemispheres, and there is a relative phase shift between the paired wings of their butterfly diagrams in a cycle, making the paired wings spatially asymmetrical on the solar equator. It is inferred that hemispherical solar activity strength should evolve in a similar way within the paired wings of a butterfly diagram in a cycle, demonstrating the paired wings phenomenon and showing the phase relationship between the northern and southern hemispherical solar activity strengths, as well as a relative phase shift between the paired wings of a butterfly diagram, which should bring about almost the same relative phase shift of hemispheric solar activity strength. (research papers)

Multiple representations and free-body diagrams: Do students benefit from using them?

Science.gov (United States)

Rosengrant, David R.

2007-12-01

Introductory physics students have difficulties understanding concepts and solving problems. When they solve problems, they use surface features of the problems to find an equation to calculate a numerical answer often not understanding the physics in the problem. How do we help students approach problem solving in an expert manner? A possible answer is to help them learn to represent knowledge in multiple ways and then use these different representations for conceptual understanding and problem solving. This solution follows from research in cognitive science and in physics education. However, there are no studies in physics that investigate whether students who learn to use multiple representations are in fact better problem solvers. This study focuses on one specific representation used in physics--a free body diagram. A free-body diagram is a graphical representation of forces exerted on an object of interest by other objects. I used the free-body diagram to investigate five main questions: (1) If students are in a course where they consistently use free body diagrams to construct and test concepts in mechanics, electricity and magnetism and to solve problems in class and in homework, will they draw free-body diagrams on their own when solving exam problems? (2) Are students who use free-body diagrams to solve problems more successful then those who do not? (3) Why do students draw free-body diagrams when solving problems? (4) Are students consistent in constructing diagrams for different concepts in physics and are they consistent in the quality of their diagrams? (5) What are possible relationships between features of a problem and how likely a student will draw a free body diagram to help them solve the problem? I utilized a mixed-methods approach to answer these questions. Questions 1, 2, 4 and 5 required a quantitative approach while question 3 required a qualitative approach, a case study. When I completed my study, I found that if students are in an

Safety culture in the nuclear versus non-nuclear organization

International Nuclear Information System (INIS)

Haber, S.B.; Shurberg, D.A.

1996-01-01

The importance of safety culture in the safe and reliable operation of nuclear organizations is not a new concept. The greatest barriers to this area of research are twofold: (1) the definition and criteria of safety culture for a nuclear organization and (2) the measurement of those attributes in an objective and systematic fashion. This paper will discuss a proposed resolution of those barriers as demonstrated by the collection of data across nuclear and non-nuclear facilities over a two year period

Energy barriers between metastable states in first-order quantum phase transitions

Science.gov (United States)

Wald, Sascha; Timpanaro, André M.; Cormick, Cecilia; Landi, Gabriel T.

2018-02-01

A system of neutral atoms trapped in an optical lattice and dispersively coupled to the field of an optical cavity can realize a variation of the Bose-Hubbard model with infinite-range interactions. This model exhibits a first-order quantum phase transition between a Mott insulator and a charge density wave, with spontaneous symmetry breaking between even and odd sites, as was recently observed experimentally [Landig et al., Nature (London) 532, 476 (2016), 10.1038/nature17409]. In the present paper, we approach the analysis of this transition using a variational model which allows us to establish the notion of an energy barrier separating the two phases. Using a discrete WKB method, we then show that the local tunneling of atoms between adjacent sites lowers this energy barrier and hence facilitates the transition. Within our simplified description, we are thus able to augment the phase diagram of the model with information concerning the height of the barrier separating the metastable minima from the global minimum in each phase, which is an essential aspect for the understanding of the reconfiguration dynamics induced by a quench across a quantum critical point.

The safety of domestic robotics: A survey of various safety-related publications

OpenAIRE

Tadele, T.S.; de Vries, Theodorus J.A.; Stramigioli, Stefano

2014-01-01

Different branches of technology are striving to come up with new advancements that will enhance civilization and ultimately improve the quality of life. In the robotics community, strides have been made to bring the use of personal robots in office and home environments on the horizon. Safety is one of the critical issues that must be guaranteed for the successful acceptance, deployment, and utilization of domestic robots. Unlike the barrier-based operational safety guarantee that is widely ...

A comparison of two approaches for solving unconstrained influence diagrams

DEFF Research Database (Denmark)

Ahlmann-Ohlsen, Kristian S.; Jensen, Finn V.; Nielsen, Thomas Dyhre

2009-01-01

Influence diagrams and decision trees represent the two most common frameworks for specifying and solving decision problems. As modeling languages, both of these frameworks require that the decision analyst specifies all possible sequences of observations and decisions (in influence diagrams, thi...

Spacelike penguin diagram effects in B implies PP decays

International Nuclear Information System (INIS)

Du, D.; Yang, M.; Zhang, D.

1996-01-01

The spacelike penguin diagram contributions to branching ratios and CP asymmetries in charmless decays of B to two pseudoscalar mesons are studied using the next-to-leading order low energy effective Hamiltonian. Both the gluonic penguin and the electroweak penguin diagrams are considered. We find that the effects are significant. copyright 1995 The American Physical Society

The use of influence diagrams for evaluating severe accident management strategies

International Nuclear Information System (INIS)

Jae, M.; Apostolakis, G.E.

1992-01-01

In this paper, the influence diagram, a new analytical tool for developing and evaluating severe accident management strategies, is presented. Influence diagrams are much simpler than decision trees because they do not lead to the large number of branches that are generated when decision trees are used in realistic problems; furthermore, they show explicitly the dependencies between the variables of the problem. One of the accident management strategies proposed for light water reactors, flooding the reactor cavity as a means of preventing vessel breach during a short-term station blackout sequence, is presented. The influence diagram associated with this strategy is constructed. Finally, the advantages of using influence diagrams in accident management are explored

Towards an international classification for patient safety : the conceptual framework

NARCIS (Netherlands)

Sherman, H.; Castro, G.; Fletcher, M.; Hatlie, M.; Hibbert, P.; Jakob, R.; Koss, R.; Lewalle, P.; Loeb, J.; Perneger, Th.; Runciman, W.; Thomson, R.; Schaaf, van der T.W.; Virtanen, M.

2009-01-01

Global advances in patient safety have been hampered by the lack of a uniform classification of patient safety concepts. This is a significant barrier to developing strategies to reduce risk, performing evidence-based research and evaluating existing healthcare policies relevant to patient safety.

An acceptability and safety study of the Duet cervical barrier and gel delivery system in Zimbabwe.

Science.gov (United States)

Montgomery, Elizabeth T; Woodsong, Cynthia; Musara, Petina; Cheng, Helen; Chipato, Tsungai; Moench, Thomas R; Spielberg, Freya; van der Straten, Ariane

2010-08-05

Adherence problems with coitally dependent, female-initiated HIV prevention methods have contributed to several trials' failure to establish efficacy. Continuous use of a cervical barrier with once-daily cleaning and immediate reinsertion may simplify use for women and improve adherence. We assessed the acceptability and safety of precoital and continuous use of the Duet, a cervical barrier and gel delivery system, in Zimbabwean women. Using a two-arm crossover design with a parallel observation group, we randomized 103 women in a 2:2:1 ratio: (1) to use the Duet continuously for 14 days, followed by a minimum of seven days of washout and then 14 days of precoital use; (2) to use the same Duet regimens in reverse order; or (3) for observation only. Women were aged 18 to 40 years; half were recruited from a pool of previous diaphragm study participants and the other half from the general community. Acceptability and adherence were assessed through an interviewer-administered questionnaire at each of two follow-up visits. Safety was monitored through pelvic speculum exams and report of adverse events. The proportion of women who reported consistent Duet use during sex was virtually identical during continuous and precoital regimens (88.6% vs. 88.9%). Partner refusal was the most common reason cited for non-use during sex in both use regimens. Not having the device handy was the most common reason cited for non-daily use (in the continuous regimen). Most women were "very comfortable" using it continuously (86.3%) and inserting it precoitally (92.8%). The most favoured Duet attribute was that it did not interfere with "natural" sex (55%). The least favoured Duet attribute was the concern that it might come out during sex (71.3%). No serious adverse events were reported during the study; 57 participants reported 90 adverse events classified as mild or moderate. There were no statistically significant differences in: (1) the proportion of women reporting adverse events

Merit exponents and control area diagrams in materials selection

International Nuclear Information System (INIS)

Zander, Johan; Sandstroem, Rolf

2011-01-01

Highlights: → Merit exponents are introduced to generalise the merit indices commonly used in materials selection. → The merit exponents can rank materials in general design situations. → To allow identification of the active merit exponent(s), control area diagrams are used. → Principles for generating the control area diagrams are presented. -- Abstract: Merit indices play a fundamental role in materials selection, since they enable ranking of materials. However, the conventional formulation of merit indices is associated with severe limitations. They are dependent on the explicit solution of the variables in the equations for the constraints from the design criteria. Furthermore, it is not always easy to determine which the controlling merit index is. To enable the ranking of materials in more general design cases, merit exponents are introduced as generalisations of the merit indices. Procedures are presented for how to compute the merit exponents numerically without having to solve equations algebraically. Merit exponents (and indices) are only valid in a certain range of property values. To simplify the identification of the controlling merit exponent, it is suggested that so called control area diagrams are used. These diagrams consist of a number of domains, each showing the active constraints and the controlling merit exponent. It is shown that the merit exponents play a crucial role when the control area diagram (CAD) is set up. The principles in the paper are developed for mechanically loaded components and are illustrated for engineering beams with two or three geometric variables.

Improving Safety through Human Factors Engineering.

Science.gov (United States)

Siewert, Bettina; Hochman, Mary G

2015-10-01

Human factors engineering (HFE) focuses on the design and analysis of interactive systems that involve people, technical equipment, and work environment. HFE is informed by knowledge of human characteristics. It complements existing patient safety efforts by specifically taking into consideration that, as humans, frontline staff will inevitably make mistakes. Therefore, the systems with which they interact should be designed for the anticipation and mitigation of human errors. The goal of HFE is to optimize the interaction of humans with their work environment and technical equipment to maximize safety and efficiency. Special safeguards include usability testing, standardization of processes, and use of checklists and forcing functions. However, the effectiveness of the safety program and resiliency of the organization depend on timely reporting of all safety events independent of patient harm, including perceived potential risks, bad outcomes that occur even when proper protocols have been followed, and episodes of "improvisation" when formal guidelines are found not to exist. Therefore, an institution must adopt a robust culture of safety, where the focus is shifted from blaming individuals for errors to preventing future errors, and where barriers to speaking up-including barriers introduced by steep authority gradients-are minimized. This requires creation of formal guidelines to address safety concerns, establishment of unified teams with open communication and shared responsibility for patient safety, and education of managers and senior physicians to perceive the reporting of safety concerns as a benefit rather than a threat. © RSNA, 2015.

The importance of design in learning from node-link diagrams

NARCIS (Netherlands)

Amelsvoort, Marije; van der Meij, Jan; Anjewierden, Anjo Allert; van der Meij, Hans

2013-01-01

Diagrams organize by location. They give spatial cues for finding and recognizing information and for making inferences. In education, diagrams are often used to help students understand and recall information. This study assessed the influence of perceptual cues on reading behavior and subsequent

Re-determination of succinonitrile (SCN) camphor phase diagram

Science.gov (United States)

Teng, Jing; Liu, Shan

2006-04-01

Low-melting temperature transparent organic materials have been extensively used to study the pattern formation and microstructure evolution. It proves to be very challenging to accurately determine the phase diagram since there is no viable way to measure the composition microscopically. In this paper, we presented the detailed experimental characterization of the phase diagram of succinonitrile (SCN)-camphor binary system. Differential scanning calorimetry, a ring-heater, and the directional solidification technique have been combined to determine the details of the phase diagram by using the purified materials. The advantages and disadvantages have been discussed for the different experimental techniques. SCN and camphor constitute a simple binary eutectic system with the eutectic composition at 23.6 wt% camphor and eutectic temperature at 37.65 °C. The solidus and the solubility of the SCN base solid solution have been precisely determined for the first time in this binary system.

Designing a supply chain of ready-mix concrete using Voronoi diagrams

Science.gov (United States)

Kozniewski, E.; Orlowski, M.; Orlowski, Z.

2017-10-01

Voronoi diagrams are used to solve scientific and practical problems in many fields. In this paper Voronoi diagrams have been applied to logistic problems in construction, more specifically in the design of the ready-mix concrete supply chain. Apart from the Voronoi diagram, the so-called time-distance circle (circle of range), which in metric space terminology is simply a sphere, appears useful. It was introduced to solve the problem of supplying concrete-related goods.

Algorithmic approach to diagram techniques

International Nuclear Information System (INIS)

Ponticopoulos, L.

1980-10-01

An algorithmic approach to diagram techniques of elementary particles is proposed. The definition and axiomatics of the theory of algorithms are presented, followed by the list of instructions of an algorithm formalizing the construction of graphs and the assignment of mathematical objects to them. (T.A.)

Diagrams in the polaron model

International Nuclear Information System (INIS)

Smondyrev, M.A.

1985-01-01

The perturbation theory for the polaron energy is systematically treated on the diagrammatic basis. Feynman diagrams being constructed allow to calculate the polaron energy up to the third order in powers of the coupling constant. Similar calculations are performed for the average number of virtual phonons

Relation between time-temperature transformation and continuous heating transformation diagrams of metallic glassy alloys

International Nuclear Information System (INIS)

Louzguine-Luzgin, Dmitri V.; Inoue, Akihisa

2005-01-01

The time-temperature transformation (TTT) diagrams for the onset of devitrification of the Ge-Ni-La and Cu-Hf-Ti glassy alloys were calculated from the isothermal differential calorimetry data using an Arrhenius equation. The continuous heating transformation (CHT) diagrams for the onset of devitrification of the glassy alloys were subsequently recalculated from TTT diagrams. The recalculation method used for conversion of the TTT into CHT diagrams produces reasonable results and is not sensitive to the type of the devitrification reaction (polymorphous or primary transformation). The diagrams allow to perform a comparison of the stabilities of glassy alloys on a long-term scale. The relationship between these diagrams is discussed

Hanford prototype-barrier status report: FY 1995

International Nuclear Information System (INIS)

Gee, G.W.; Ward, A.L.; Gilmore, B.G.; Ligotke, M.W.; Link, S.O.

1995-11-01

Surface barriers (or covers) have been proposed for use at the Hanford Site as a means to isolate certain waste sites that, for reasons of cost or worker safety or both, may not be exhumed. Surface barriers are intende to isolated the wastes from the accessible environment and to provide long-term protection to future populations that might use the Hanford Site. Currently, no ''proven'' long-term barrier system is available. For this reason, the Hanford Site Permanent Isolation Surface-Barrier Development Program (BDP) was organized to develop the technology needed to provide long-term surface barrier capability for the Hanford Site for the US Department of Energy (DOE). Designs have been proposed to meet the most stringent needs for long-term waste disposal. The objective of the current barrier design is to use natural materials to develop a protective barrier system that isolates wastes for at least 1000 years by limiting water, plant, animal, and human intrusion; and minimizing erosion. The design criteria for water drainage has been set at 0.5 mm/yr. While other design criteria are more qualitative, it is clear that waste isolation for an extended time is the prime objective of the design. Constructibility and performance. are issues that can be tested and dealt with by evaluating prototype designs prior to extensive construction and deployment of covers for waste sites at Hanford

The Butterfly Diagram Internal Structure

International Nuclear Information System (INIS)

Ternullo, Maurizio

2013-01-01

A time-latitude diagram, where the spotgroup area is taken into account, is presented for cycles 12 through 23. The results show that the spotted area is concentrated in few, small portions ( k nots ) of the Butterfly Diagram (BD). The BD may be described as a cluster of knots. Knots are distributed in the butterfly wings in a seemingly randomly way. A knot may appear at either lower or higher latitudes than previous ones, in spite of the prevalent tendency to appear at lower and lower latitudes. Accordingly, the spotted area centroid, far from continuously drifting equatorward, drifts poleward or remains stationary in any hemisphere for significant fractions (≈ 1/3) of the cycle total duration. In a relevant number of semicycles, knots seem to form two roughly parallel, oblique c hains , separated by an underspotted band. This picture suggests that two (or more) ''activity streams'' approach the equator at a rate higher than the spot zone as a whole.

Application of the cause-consequence diagram method to static systems

International Nuclear Information System (INIS)

Andrews, J.D.; Ridley, L.M.

2002-01-01

In the last 30 years, various mathematical models have been used to identify the effect of component failures on the performance of a system. The most frequently used technique for system reliability assessment is Fault Tree Analysis (FTA) and a large proportion of its popularity can be attributed to the fact that it provides a very good documentation of the way that the system failure logic was developed. Exact quantification of the fault tree, however, can be problematic for very large systems and in such situations, approximations can be used. Alternatively, an exact result can be obtained via the conversion of the fault tree into a binary decision diagram (BDD). The BDD, however, loses all failure logic documentation during the conversion process. This paper outlines the use of the cause-consequence diagram method as a tool for system risk and reliability analysis. As with the FTA method, the cause-consequence diagram documents the failure logic of the system. In addition to this the cause-consequence diagram produces the exact failure probability in a very efficient calculation procedure. The cause-consequence diagram technique has been applied to a static system and shown to yield the same result as those produced by the solution of the equivalent fault tree and BDD. On the basis of this general rules have been devised for the correct construction of the cause-consequence diagram given a static system. The use of the cause-consequence method in this manner has significant implications in terms of efficiency of the reliability analysis and can be shown to have benefits for static systems

Uniting Control Lyapunov and Control Barrier Functions

NARCIS (Netherlands)

Romdlony, Zakiyullah; Jayawardhana, Bayu

2014-01-01

In this paper, we propose a nonlinear control design for solving the problem of stabilization with guaranteed safety. The design is based on the merging of a Control Lyapunov Function and a Control Barrier Function. The proposed control method allows us to combine the design of a stabilizer based on

Sweden-Lithuania bilateral cooperation in nuclear safety

International Nuclear Information System (INIS)

Nistad, J.H.; Vaisnys, P.

1996-01-01

This cooperation started in early 1992 shortly after Lithuania became a newly independent republic. The results from the bilateral co-operation in the field of nuclear safety are very fruitful and promising. The work is progressing in a very efficient and cost-effective way. The pace of progress is to a great extent governed by the resources the Lithuanian partners can allocate. The Swedish Government has up to now allocated more than 200 MSEK (>30 MUSD) for this bilateral cooperation in nuclear safety enhancement. This paper gives an overview of the main content and achievements of the Swedish-Lithuanian cooperation. 1 tab, 2 diagrams

Conformational properties of rigid-chain amphiphilic macromolecules : The phase diagram

NARCIS (Netherlands)

Markov, V. A.; Vasilevskaya, V. V.; Khalatur, P. G.; ten Brinke, G.; Khokhlov, A. R.

The coil-globule transition in rigid-chain amphiphilic macromolecules was studied by means of computer simulation, and the phase diagrams for such molecules in the solvent quality-persistence length coordinates were constructed. It was shown that the type of phase diagram depends to a substantial

Phase diagram of the disordered Bose-Hubbard model

International Nuclear Information System (INIS)

Gurarie, V.; Pollet, L.; Prokof'ev, N. V.; Svistunov, B. V.; Troyer, M.

2009-01-01

We establish the phase diagram of the disordered three-dimensional Bose-Hubbard model at unity filling which has been controversial for many years. The theorem of inclusions, proven by Pollet et al. [Phys. Rev. Lett. 103, 140402 (2009)] states that the Bose-glass phase always intervenes between the Mott insulating and superfluid phases. Here, we note that assumptions on which the theorem is based exclude phase transitions between gapped (Mott insulator) and gapless phases (Bose glass). The apparent paradox is resolved through a unique mechanism: such transitions have to be of the Griffiths type when the vanishing of the gap at the critical point is due to a zero concentration of rare regions where extreme fluctuations of disorder mimic a regular gapless system. An exactly solvable random transverse field Ising model in one dimension is used to illustrate the point. A highly nontrivial overall shape of the phase diagram is revealed with the worm algorithm. The phase diagram features a long superfluid finger at strong disorder and on-site interaction. Moreover, bosonic superfluidity is extremely robust against disorder in a broad range of interaction parameters; it persists in random potentials nearly 50 (!) times larger than the particle half-bandwidth. Finally, we comment on the feasibility of obtaining this phase diagram in cold-atom experiments, which work with trapped systems at finite temperature.

The Critical Importance of Russell's Diagram

Science.gov (United States)

Gingerich, O.

2013-04-01

The idea of dwarf and giants stars, but not the nomenclature, was first established by Eijnar Hertzsprung in 1905; his first diagrams in support appeared in 1911. In 1913 Henry Norris Russell could demonstrate the effect far more strikingly because he measured the parallaxes of many stars at Cambridge, and could plot absolute magnitude against spectral type for many points. The general concept of dwarf and giant stars was essential in the galactic structure work of Harlow Shapley, Russell's first graduate student. In order to calibrate the period-luminosity relation of Cepheid variables, he was obliged to fall back on statistical parallax using only 11 Cepheids, a very sparse sample. Here the insight provided by the Russell diagram became critical. The presence of yellow K giant stars in globular clusters credentialed his calibration of the period-luminosity relation by showing that the calibrated luminosity of the Cepheids was comparable to the luminosity of the K giants. It is well known that in 1920 Shapley did not believe in the cosmological distances of Heber Curtis' spiral nebulae. It is not so well known that in 1920 Curtis' plot of the period-luminosity relation suggests that he didn't believe it was a physical relation and also he failed to appreciate the significance of the Russell diagram for understanding the large size of the Milky Way.

Warped penguin diagrams

International Nuclear Information System (INIS)

Csaki, Csaba; Grossman, Yuval; Tanedo, Philip; Tsai, Yuhsin

2011-01-01

We present an analysis of the loop-induced magnetic dipole operator in the Randall-Sundrum model of a warped extra dimension with anarchic bulk fermions and an IR brane-localized Higgs. These operators are finite at one-loop order and we explicitly calculate the branching ratio for μ→eγ using the mixed position/momentum space formalism. The particular bound on the anarchic Yukawa and Kaluza-Klein (KK) scales can depend on the flavor structure of the anarchic matrices. It is possible for a generic model to either be ruled out or unaffected by these bounds without any fine-tuning. We quantify how these models realize this surprising behavior. We also review tree-level lepton flavor bounds in these models and show that these are on the verge of tension with the μ→eγ bounds from typical models with a 3 TeV Kaluza-Klein scale. Further, we illuminate the nature of the one-loop finiteness of these diagrams and show how to accurately determine the degree of divergence of a five-dimensional loop diagram using both the five-dimensional and KK formalism. This power counting can be obfuscated in the four-dimensional Kaluza-Klein formalism and we explicitly point out subtleties that ensure that the two formalisms agree. Finally, we remark on the existence of a perturbative regime in which these one-loop results give the dominant contribution.

Nitric Acid Revamp and Upgrading of the Alarm & Protection Safety System at Petrokemija, Croatia

Directory of Open Access Journals (Sweden)

Hoško, I.

2012-04-01

Full Text Available Every industrial production, particularly chemical processing, demands special attention in conducting the technological process with regard to the security requirements. For this reason, production processes should be continuously monitored by means of control and alarm safety instrumented systems. In the production of nitric acid at Petrokemija d. d., the original alarm safety system was designed as a combination of an electrical relay safety system and transistorized alarm module system. In order to increase safety requirements and modernize the technological process of nitric acid production, revamping and upgrading of the existing alarm safety system was initiated with a new microprocessor system. The newly derived alarm safety system, Simatic PCS 7, links the function of "classically" distributed control (DCS and logical systems in a common hardware and software platform with integrated engineering tools and operator interface to meet the minimum safety standards with safety integrity level 2 (SIL2 up to level 3 (SIL3, according to IEC 61508 and IEC 61511. This professional paper demonstrates the methodology of upgrading the logic of the alarm safety system in the production of nitric acid in the form of a logical diagram, which was the basis for a further step in its design and construction. Based on the mentioned logical diagram and defined security requirements, the project was implemented in three phases: analysis and testing, installation of the safety equipment and system, and commissioning. Developed also was a verification system of all safety conditions, which could be applied to other facilities for production of nitric acid. With the revamped and upgraded interlock alarm safety system, a new and improved safety boundary in the production of nitric acid was set, which created the foundation for further improvement of the production process in terms of improved analysis.

Three-body crystallization diagrams and the cooling of white dwarfs.

Science.gov (United States)

Segretain, L.

1996-06-01

The 3-body crystallization diagrams of C/O/Ne ionic mixtures characteristic of white dwarf interiors are examined within the framework of the density-functional theory of freezing. The crystallization process is described more accurately than in former calculations where the three-component system was treated as an effective two-component mixture (Segretain et al. 1994). The distillation process due to neon-crystallization is found to occur only for the late stages of crystallization. At the beginning, the presence of neon plays only a minor role and the phase diagram resembles a pure carbon-oxygen diagram. The final phase diagram is found to exhibit an azeotropic point with a neon concentration x_Ne_=0.22, a carbon concentration x_C_=0.78 and an oxygen concentration x_O_=0, so that during the distillation process, the fluid crystallizes into a pure neon-carbon solid. The critical temperature is T_A_=0.85T_C_, where T_C_ is the pure carbon crystallization temperature. We use this accurate phase diagram to calculate the total gravitational energy released during white dwarf crystallization and the related time delay. The final result yields {DELTA}τ=~2.6Gyr, among which about 20% are due to the neon-distillation process.

Proposal for a research programme on geological disposal of radioactive waste in the Netherlands

International Nuclear Information System (INIS)

1984-06-01

The present report sets out a tentative research program related to radiologic safety of geological disposal of radioactive waste, set against the background of present knowledge in this field. The final stage of this program has to lead to a definitive appraisal of the suitability of the site explored in that stage for disposal of high-level radioactive waste. Subsequent stages of the research effort is outlined in a critical path diagram. Radiological safety figures as the central factor in making choices. The report indicates the state of the art in different specialisms involved in the study of both natural barriers (rheology, hydrology, radionuclide transport, radiation damage) and artificial barriers (mining engineering) for geological disposal. (G.J.P.)

Natural analogues for containment-providing barriers for a HLW repository in salt

Energy Technology Data Exchange (ETDEWEB)

Wolf, J.; Noseck, U.

2015-06-15

In 2005, a German research project was started to develop a novel approach to prove safety for a HLW repository in a salt formation, to refine the safety concept, to identify open scientific issues and to define necessary R&D work. This project aimed at identifying the key information for a HLW repository in salt. One important question is how this information may be best fulfilled by natural analogue studies. This question is answered by starting a review of the required key information needs of the safety case (post-closure phase) in order to assess whether or not these requirements can be supported by natural analogues information. In order to structure the review and to address the key elements of the safety concepts, three types of natural analogues are distinguished: (i) natural analogues for the integrity of the geological barrier, (ii) natural analogues for the integrity of the geotechnical barriers and (iii) natural analogues for release scenarios. For the safety case in salt type (i) and (ii) are of highest importance and are treated in this paper. The assessment documented in this paper on the one hand indicates the high potential benefit of natural analogues for a safety case in salt and on the other hand helps to focus the available human and financial resources for the safety case on the most safety-relevant aspects. (authors)

Protection against malevolent use of vehicles at Nuclear Power Plants. Vehicle barrier system selection guidance

International Nuclear Information System (INIS)

Nebuda, D.T.

1994-08-01

This manual provides a simplified procedure for selecting land vehicle barriers that will stop the design basis vehicle threat adopted by the U.S. Nuclear Regulatory Commission. Proper selection and construction of vehicle barriers should prevent intrusion of the design basis vehicle. In addition, vital safety related equipment should survive a design basis vehicle bomb attack when vehicle barriers are properly selected, sited, and constructed. This manual addresses passive vehicle barriers, active vehicle barriers, and site design features that can be used to reduce vehicle impact velocity

CRASH TEST AND EVALUATION OF RESTRAINED SAFETY-SHAPE CONCRETE BARRIERS ON CONCRETE BRIDGE DECK

Science.gov (United States)

2018-01-01

This research designed and tested a new portable concrete barrier that meets the performance of MASH TL-4 and can be used in temporary and permanent applications on bridge decks. Additionally, this new barrier system will minimize deflection, allowin...

Improving Patient Safety: Improving Communication.

Science.gov (United States)

Bittner-Fagan, Heather; Davis, Joshua; Savoy, Margot

2017-12-01

Communication among physicians, staff, and patients is a critical element in patient safety. Effective communication skills can be taught and improved through training and awareness. The practice of family medicine allows for long-term relationships with patients, which affords opportunities for ongoing, high-quality communication. There are many barriers to effective communication, including patient factors, clinician factors, and system factors, but tools and strategies exist to address these barriers, improve communication, and engage patients in their care. Use of universal precautions for health literacy, appropriate medical interpreters, and shared decision-making are evidence-based tools that improve communication and increase patient safety. Written permission from the American Academy of Family Physicians is required for reproduction of this material in whole or in part in any form or medium.

Effect of a Diagram on Primary Students' Understanding About Electric Circuits

Science.gov (United States)

Preston, Christine Margaret

2017-09-01

This article reports on the effect of using a diagram to develop primary students' conceptual understanding about electric circuits. Diagrammatic representations of electric circuits are used for teaching and assessment despite the absence of research on their pedagogical effectiveness with young learners. Individual interviews were used to closely analyse Years 3 and 5 (8-11-year-old) students' explanations about electric circuits. Data was collected from 20 students in the same school providing pre-, post- and delayed post-test dialogue. Students' thinking about electric circuits and changes in their explanations provide insights into the role of diagrams in understanding science concepts. Findings indicate that diagram interaction positively enhanced understanding, challenged non-scientific views and promoted scientific models of electric circuits. Differences in students' understanding about electric circuits were influenced by prior knowledge, meta-conceptual awareness and diagram conventions including a stylistic feature of the diagram used. A significant finding that students' conceptual models of electric circuits were energy rather than current based has implications for electricity instruction at the primary level.

Barriers to return to work after burn injuries.

Science.gov (United States)

Esselman, Peter C; Askay, Shelley Wiechman; Carrougher, Gretchen J; Lezotte, Dennis C; Holavanahalli, Radha K; Magyar-Russell, Gina; Fauerbach, James A; Engrav, Loren H

2007-12-01

To identify barriers to return to work after burn injury as identified by the patient. A cohort study with telephone interview up to 1 year. Hospital-based burn centers at 3 national sites. Hospitalized patients (N=154) meeting the American Burn Association criteria for major burn injury, employed at least 20 hours a week at the time of injury, and with access to a telephone after discharge. Patients were contacted via telephone every 2 weeks up to 4 months, then monthly up to 1 year after discharge. A return to work survey was used to identify barriers that prevented patients from returning to work. A graphic rating scale determined the impact of each barrier. By 1 year, 79.7% of patients returned to work. Physical and wound issues were barriers early after discharge. Although physical abilities continued to be a significant barrier up to 1 year, working conditions (temperature, humidity, safety) and psychosocial factors (nightmares, flashbacks, appearance concerns) became important issues in those with long-term disability. The majority of patients return to work after a burn injury. Although physical and work conditions are important barriers, psychosocial issues need to be evaluated and treated to optimize return to work.

Asteroseismic Diagram for Subgiants and Red Giants

Energy Technology Data Exchange (ETDEWEB)

Gai, Ning; Tang, Yanke [College of Physics and Electronic information, Dezhou University, Dezhou 253023 (China); Yu, Peng [College of Physics and Electronic Engineering, Chongqing Normal University, Chongqing 401331 (China); Dou, Xianghua, E-mail: ning_gai@163.com, E-mail: tyk450@163.com [Shandong Provincial Key Laboratory of Biophysics, Dezhou University, Dezhou 253023 (China)

2017-02-10

Asteroseismology is a powerful tool for constraining stellar parameters. NASA’s Kepler mission is providing individual eigenfrequencies for a huge number of stars, including thousands of red giants. Besides the frequencies of acoustic modes, an important breakthrough of the Kepler mission is the detection of nonradial gravity-dominated mixed-mode oscillations in red giants. Unlike pure acoustic modes, mixed modes probe deeply into the interior of stars, allowing the stellar core properties and evolution of stars to be derived. In this work, using the gravity-mode period spacing and the large frequency separation, we construct the ΔΠ{sub 1}–Δ ν asteroseismic diagram from models of subgiants and red giants with various masses and metallicities. The relationship ΔΠ{sub 1}–Δ ν is able to constrain the ages and masses of the subgiants. Meanwhile, for red giants with masses above 1.5 M {sub ⊙}, the ΔΠ{sub 1}–Δ ν asteroseismic diagram can also work well to constrain the stellar age and mass. Additionally, we calculate the relative “isochrones” τ , which indicate similar evolution states especially for similar mass stars, on the ΔΠ{sub 1}–Δ ν diagram.

The colour-magnitude diagram of NGC 5053

International Nuclear Information System (INIS)

Walker, M.F.; Pike, C.D.; McGee, J.D.

1976-01-01

The colour-magnitude diagram of NGC 5053 has been derived to V = 21.1 from photographic and electronographic observations. The electronographic observations were obtained with an experimental Spectracon image-converter, having photocathode and exit window dimensions of 20 x 30 mm, mounted at the prime-focus of the 120-in. Lick reflector. The photographic observations were obtained with the 20-in. Carnegie astrograph and the 36-in. Crossley reflector. The colour-magnitude diagram resembles that of M92, with the difference that a red horizontal branch is more pronounced than the asymptotic branch in NGC 5053. The topology of the horizontal branch is that of clusters with an intermediate metal content and is thus at variance with the mean period of the RR Lyr stars and the unreddened colour of the subgiant branch read at the magnitude level of the horizontal branch, both of which would indicate an extremely low metal content. If comparison of the colour-magnitude diagrams of NGC 5053 and M92 is valid, then the reddening of NGC 5053 is Esub(B-V) = 0.02 and the apparent distance modulus is m-M = 16.08 +- 0.08. (author)

Calculation of Fe–B–V ternary phase diagram

International Nuclear Information System (INIS)

Homolová, Viera; Kroupa, Aleš; Výrostková, Anna

2012-01-01

Highlights: ► Phase diagram of Fe–B–V system was modelled by CALPHAD method. ► Database for thermodynamic calculations for Fe–B–V system was created. ► The new ternary phase was found in 67Fe–18B–15V [in at.%] alloy. - Abstract: The phase equilibria of the Fe–B–V ternary system are studied experimentally and theoretically in this paper. Phase diagram of the system was modelled by CALPHAD method. Boron was modelled as an interstitial element in the FCC and BCC solid solutions. The calculations of isothermal sections of phase diagram are compared with our experimental results at 903 and 1353 K and with available literature experimental data. New ternary phase (with chemical composition 28Fe32V40B in at.%) was found in 67Fe–18B–15V alloy [in at.%]. Further experimental studies for the determination of exact nature of the ternary phase including crystallographic information are necessary.

Phase Diagrams of Electrostatically Self-Assembled Amphiplexes

Energy Technology Data Exchange (ETDEWEB)

V Stanic; M Mancuso; W Wong; E DiMasi; H Strey

2011-12-31

We present the phase diagrams of electrostatically self-assembled amphiplexes (ESA) comprised of poly(acrylic acid) (PAA), cetyltrimethylammonium chloride (CTACl), dodecane, pentanol, and water at three different NaCl salt concentrations: 100, 300, and 500 mM. This is the first report of phase diagrams for these quinary complexes. Adding a cosurfactant, we were able to swell the unit cell size of all long-range ordered phases (lamellar, hexagonal, Pm3n, Ia3d) by almost a factor of 2. The added advantage of tuning the unit cell size makes such complexes (especially the bicontinuous phases) attractive for applications in bioseparation, drug delivery, and possibly in oil recovery.

Critical safety issues in the design of fusion machines

International Nuclear Information System (INIS)

Kramer, W.

1991-01-01

In the course of developing fusion machines both general safety considerations and safety assessments for the various components and systems of actual machines increase in number and become more and more coherent. This is particularly true for the NET/ITER projects where safety analysis plays an increasing role for the design of the machine. Since in a D/T tokamak the radiological hazards will be dominant basic radiological safety objectives are discussed. Critical safety issues as identified in particular by the NET/ITER community are reviewed. Subsequently, issues of major concern are considered both for normal operation and for conceivable accidents. The following accidents are considered to be crucial: Loss of cooling in plasma facing components, loss of vacuum, tritium system failure, and magnet system failure. To mitigate accident consequences a confinement concept based on passive features and multiple barriers including detritiation and filtering has to be applied. The reactor building as final barrier needs special attention to cope with both internal and external hazards. (orig.)

Prevent recurrence of nuclear disaster (2). Reconstruction of safety logic diagram of nuclear system

International Nuclear Information System (INIS)

Miyano, Hiroshi; Sekimura, Naoto; Nakamura, Takao; Narumiya, Yoshiyuki

2012-01-01

On March 11, 2011, severe accident occurred at multi units of nuclear power caused by natural disaster, which was the first of nuclear power in the world, and lead to nuclear disaster which contaminated a wide range of land and caused surrounding residents to evacuate for a long-term. Since Cyuetsu-oki earthquake and before this accident, Atomic Energy Society of Japan had activities to investigate 'safety of nuclear system' against earthquake beyond any expectation, identify research items and work out roadmap on future research activities. Correspondence against tsunami such as this accident was discussed but not included as proposal because of low tsunami hazards awareness. Based on this reflection and to prevent recurrence of nuclear disaster, reconsideration of nuclear safety from the standpoint of defense-in-depth against hazards beyond any expectation had been performed and proposed to establish roadmap for its realization. Basic principle of nuclear safety consisted of eleven principles so as to protect personnel and environment from harmful effects of radiation derived from nuclear facilities and their activities, which were categorized into three groups (responsibility and management system, personnel and environmental protection and prevention of accident initiation and effect mitigation). (T. Tanaka)

Safety precautions in atomic pile control (1962)

International Nuclear Information System (INIS)

Furet, J.

1962-01-01

We have been led to study the problem of safety in atomic pile control as a result of our participation on the one hand in the planning of C.E.A. atomic piles, and on the other hand in the pile safety sub omission considering atomic pile safety of operational or planned C.E.A. piles. We have thus had to consider the wishes occurring in piles during their operation and also their behaviour in the dynamic state The present work deals mainly with the importance of intrinsic safety devices, with the influence of reactivity variations on the power fluctuations during accidental operation, and with the development of robust and reliable safety appliances. The starting p accident has been especially studied both for low-flux piles where a compromise is necessary between the response time of the safety appliances and the statistical fluctuations and for high lux piles where xenon poisoning has an effect on the lower limit of the velocity of reactivity liberation. The desirability has been stressed of automation as a safety factor in atomic pile control. The details required for an understanding of the diagrams of the apparatus are given. (author) [fr

Project Management Plan for the INEL technology logic diagrams

International Nuclear Information System (INIS)

Rudin, M.J.

1992-10-01

This Project Management Plan (PjMP) describes the elements of project planning and control that apply to activities outlined in Technical Task Plan (TTP) ID-121117, ''Technology Logic Diagrams For The INEL.'' The work on this project will be conducted by personnel in EG ampersand G Idaho, Inc.'s Waste Technology Development Program. Technology logic diagrams represent a formal methodology to identify technology gaps or needs within Environmental Restoration/Waste Management Operations, which will focus on Office of Environmental Restoration and Waste Management (EM-50) research and development, demonstration, test, and evaluation efforts throughout the US Department of Energy complex. This PjMP describes the objectives, organization, roles and responsibilities, workscope and processes for implementing and managing the technology logic diagram for the Idaho National Engineering Laboratory project

Decorated-box-diagram contributions to Bhabha scattering. Pt. 1

International Nuclear Information System (INIS)

Faeldt, G.; Osland, P.

1994-01-01

We evaluate, in the light-energy limit, s>>vertical stroke tvertical stroke >>m 2 >>λ 2 , the sum of amplitudes corresponding to a class of Feynman diagrams describing two-loop virtual photonic corrections to Bhabha scattering. The diagrams considered are box and crossed-box diagrams with an extra photon decorating one of the fermion lines. The mathematical method employed is that of Mellin transforms. In the eikonal approximation, this sum of two-loop amplitudes has previously been evaluated, and found to be equal to the sum of the box and crossed-box amplitudes, multiplied by the electric form factor of the electron. We obtain a similar factorization, but with the form factor replaced by another expression involving the logarithms log(λ 2 /m 2 ) and log(λ 2 /vertical stroke tvertical stroke ). (orig.)

Nonplanar on-shell diagrams and leading singularities of scattering amplitudes

Energy Technology Data Exchange (ETDEWEB)

Chen, Baoyi; Cheung, Yeuk-Kwan E.; Li, Yunxuan; Xie, Ruofei; Xin, Yuan [Nanjing University, Department of Physics, Nanjing (China); Chen, Gang [Zhejiang Normal University, Department of Physics, Jinhua, Zhejiang (China); Nanjing University, Department of Physics, Nanjing (China)

2017-02-15

Bipartite on-shell diagrams are the latest tool in constructing scattering amplitudes. In this paper we prove that a Britto-Cachazo-Feng-Witten (BCFW) decomposable on-shell diagram process a rational top form if and only if the algebraic ideal comprised the geometrical constraints are shifted linearly during successive BCFW integrations. With a proper geometric interpretation of the constraints in the Grassmannian manifold, the rational top form integration contours can thus be obtained, and understood, in a straightforward way. All rational top form integrands of arbitrary higher loops leading singularities can therefore be derived recursively, as long as the corresponding on-shell diagram is BCFW decomposable. (orig.)

Project Guarantee 1985. Final repository for low- and intermediate level radioactive wastes: Safety report

International Nuclear Information System (INIS)

Anon.

1985-01-01

Storage of radioactive waste must delay the return of radionuclides to the biosphere for a long period of time and must maintain the release rates at a sufficiently low level for all time. This is achieved with the aid of a series of safety barriers which consist, on the one hand, of technical barriers in the repository and, on the other hand , of natural geological barriers as they occur at the repository location. In order to assess the efficiency of the barriers, the working methods of the technical barriers and the host rock must be understood. This understanding is transferred into quantitative models in order to calculate the safety of the repository. The individual barriers and the methods used to modelling their functions were described in volume NGB 85-07 of the Project Guarantee 1985 report series and the data necessary for modelling were given. The models and data are used in the safety analysis, the results of which are contained in the present report. Safety considerations show that models are available in Switzerland which allow, in principle, an assessment of the long-term behaviour of a repository for low- and intermediate-level waste. The evaluation of earlier studies and experimental work, suitable laboratory measurements and results from field research enable compilation of a representative data-set so that the requirements for quantitative statements on safety of final disposal are met from this side also. The safety calculations show that the radiation doses calculated for a base case scenario with realistic/conservative parameter values are negligibly low. Also, radiation doses which are clearly under the protection standard of 10 mrem per year result for conservative values and the cumulation of several conservative assumptions. Even assuming exposure of the repository by erosion, a radiotoxicity of the soil formed results which is under natural values

Integrating Safety and Mission Assurance into Systems Engineering Modeling Practices

Science.gov (United States)

Beckman, Sean; Darpel, Scott

2015-01-01

During the early development of products, flight, or experimental hardware, emphasis is often given to the identification of technical requirements, utilizing such tools as use case and activity diagrams. Designers and project teams focus on understanding physical and performance demands and challenges. It is typically only later, during the evaluation of preliminary designs that a first pass, if performed, is made to determine the process, safety, and mission quality assurance requirements. Evaluation early in the life cycle, though, can yield requirements that force a fundamental change in design. This paper discusses an alternate paradigm for using the concepts of use case or activity diagrams to identify safety hazard and mission quality assurance risks and concerns using the same systems engineering modeling tools being used to identify technical requirements. It contains two examples of how this process might be used in the development of a space flight experiment, and the design of a Human Powered Pizza Delivery Vehicle, along with the potential benefits to decrease development time, and provide stronger budget estimates.

NUCLEAR SAFETY DESIGN BASES FOR LICENSE APPLICATION

International Nuclear Information System (INIS)

Garrett, R.J.

2005-01-01

The purpose of this report is to identify and document the nuclear safety design requirements that are specific to structures, systems, and components (SSCs) of the repository that are important to safety (ITS) during the preclosure period and to support the preclosure safety analysis and the license application for the high-level radioactive waste (HLW) repository at Yucca Mountain, Nevada. The scope of this report includes the assignment of nuclear safety design requirements to SSCs that are ITS and does not include the assignment of design requirements to SSCs or natural or engineered barriers that are important to waste isolation (ITWI). These requirements are used as input for the design of the SSCs that are ITS such that the preclosure performance objectives of 10 CFR 63.111 [DIRS 156605] are met. The natural or engineered barriers that are important to meeting the postclosure performance objectives of 10 CFR 63.113 [DIRS 156605] are identified as ITWI. Although a structure, system, or component (SSC) that is ITS may also be ITWI, this report is only concerned with providing the nuclear safety requirements for SSCs that are ITS to prevent or mitigate event sequences during the repository preclosure period

Quantitative study of FORC diagrams in thermally corrected Stoner– Wohlfarth nanoparticles systems

International Nuclear Information System (INIS)

De Biasi, E.; Curiale, J.; Zysler, R.D.

2016-01-01

The use of FORC diagrams is becoming increasingly popular among researchers devoted to magnetism and magnetic materials. However, a thorough interpretation of this kind of diagrams, in order to achieve quantitative information, requires an appropriate model of the studied system. For that reason most of the FORC studies are used for a qualitative analysis. In magnetic systems thermal fluctuations 'blur' the signatures of the anisotropy, volume and particle interactions distributions, therefore thermal effects in nanoparticles systems conspire against a proper interpretation and analysis of these diagrams. Motivated by this fact, we have quantitatively studied the degree of accuracy of the information extracted from FORC diagrams for the special case of single-domain thermal corrected Stoner– Wohlfarth (easy axes along the external field orientation) nanoparticles systems. In this work, the starting point is an analytical model that describes the behavior of a magnetic nanoparticles system as a function of field, anisotropy, temperature and measurement time. In order to study the quantitative degree of accuracy of our model, we built FORC diagrams for different archetypical cases of magnetic nanoparticles. Our results show that from the quantitative information obtained from the diagrams, under the hypotheses of the proposed model, is possible to recover the features of the original system with accuracy above 95%. This accuracy is improved at low temperatures and also it is possible to access to the anisotropy distribution directly from the FORC coercive field profile. Indeed, our simulations predict that the volume distribution plays a secondary role being the mean value and its deviation the only important parameters. Therefore it is possible to obtain an accurate result for the inversion and interaction fields despite the features of the volume distribution. - Highlights: • Quantify the degree of accuracy of the information obtained using the FORC diagrams. �

Model-Driven Development of Safety Architectures

Science.gov (United States)

Denney, Ewen; Pai, Ganesh; Whiteside, Iain

2017-01-01

We describe the use of model-driven development for safety assurance of a pioneering NASA flight operation involving a fleet of small unmanned aircraft systems (sUAS) flying beyond visual line of sight. The central idea is to develop a safety architecture that provides the basis for risk assessment and visualization within a safety case, the formal justification of acceptable safety required by the aviation regulatory authority. A safety architecture is composed from a collection of bow tie diagrams (BTDs), a practical approach to manage safety risk by linking the identified hazards to the appropriate mitigation measures. The safety justification for a given unmanned aircraft system (UAS) operation can have many related BTDs. In practice, however, each BTD is independently developed, which poses challenges with respect to incremental development, maintaining consistency across different safety artifacts when changes occur, and in extracting and presenting stakeholder specific information relevant for decision making. We show how a safety architecture reconciles the various BTDs of a system, and, collectively, provide an overarching picture of system safety, by considering them as views of a unified model. We also show how it enables model-driven development of BTDs, replete with validations, transformations, and a range of views. Our approach, which we have implemented in our toolset, AdvoCATE, is illustrated with a running example drawn from a real UAS safety case. The models and some of the innovations described here were instrumental in successfully obtaining regulatory flight approval.

Richards Barrier LA Reference Design Feature Evaluation

International Nuclear Information System (INIS)

N.E. Kramer

1999-01-01

The Richards Barrier is one of the design features of the repository to be considered for the License Application (LA), Richards was a soil scientist who first described the diversion of moisture between two materials with different hydrologic properties. In this report, a Richards Barrier is a special type of backfill with a fine-grained material (such as sand) overlaying a coarse-grained material (such as gravel). Water that enters an emplacement drift will first encounter the fine-grained material and be transported around the coarse-grained material covering the waste package, thus protecting the waste package from contact with most of the groundwater. The objective of this report is to discuss the benefits and liabilities to the repository by the inclusion of a Richards Barrier type backfill in emplacement drifts. The Richards Barrier can act as a barrier to water flow, can reduce the waste package material dissolution rate, limit mobilization of the radionuclides, and can provide structural protection for the waste package. The scope of this report is to: (1) Analyze the behavior of barrier materials following the intrusion of groundwater for influxes of 1 to 300 mm per year. The report will demonstrate diversion of groundwater intrusions into the barrier over an extended time period when seismic activity and consolidation may cause the potential for liquefaction and settlement of the Richards Barrier. (2) Review the thermal effects of the Richards Barrier on material behavior. (3) Analyze the effect of rockfall on the performance of the Richards Barrier and the depth of the barrier required to protect waste packages under the barrier. (4) Review radiological and heating conditions on placement of multiple layers of the barrier. Subsurface Nuclear Safety personnel will perform calculations to determine the radiation reduction-time relationship and shielding capacity of the barrier. (5) Evaluate the effects of ventilation on cooling of emplacement drifts and

Development and improvement of safety analysis code for geological disposal

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

In order to confirm the long-term safety concerning geological disposal, probabilistic safety assessment code and other analysis codes, which can evaluate possibility of each event and influence on engineered barrier and natural barrier by the event, were introduced. We confirmed basic functions of those codes and studied the relation between those functions and FEP/PID which should be taken into consideration in safety assessment. We are planning to develop 'Nuclide Migration Assessment System' for the purpose of realizing improvement in efficiency of assessment work, human error prevention for analysis, and quality assurance of the analysis environment and analysis work for safety assessment by using it. As the first step, we defined the system requirements and decided the system composition and functions which should be mounted in them based on those requirements. (author)

Demonstration of Risk Profiling for promoting safety in SME´s

DEFF Research Database (Denmark)

Jørgensen, Kirsten; Duijm, Nijs Jan; Troen, Hanne

2011-01-01

Purpose – The purpose of this paper is to identify and assess the risks and potential risks that may lead to accidents. It aims to look at how to improve risk assessment within SMEs for the benefit of all staff. Design/methodology/approach – The research included results from a Dutch project which...... identifies accident risks and safety barriers that are presented in a huge database and risk calculator. The method was first to develop a simple way of accessing this enormous amount of data, second, to develop a tool to observe risks and safety barriers in SMEs and to investigate the usefulness...... of the developed tools in real life, third, to collect data on risks and safety barriers in SMEs for two occupations by following 20 people for three days each and to create a risk profile for each occupations. Findings – The result is a simple way to go through all types of risks for accidents – a tool for risk...

The annihilation diagram in three-body D-meson decay

International Nuclear Information System (INIS)

Donoghue, J.F.; Holstein, B.R.

1981-01-01

We discuss some features of three-body decays of the D meson cohich are puzzling from the standpoint of the annihilation diagram. As a result, we (1) provide an upper bound on the lifetime ratio of D's, tau + sub(D)/tau 0 sub(D) smaller than 2.5 +- 3.4 and (2) argue that the puzzles are resolved, even if somewhat inelegantly, if final state interactions generate the annihilation diagram. (orig.)

Barriers to Effective Teamwork Relating to Pediatric Resuscitations: Perceptions of Pediatric Emergency Medicine Staff.

Science.gov (United States)

Sherman, Joshua M; Chang, Todd P; Ziv, Nurit; Nager, Alan L

2017-10-09

In the pediatric emergency department (PED), resuscitations require medical teams form ad hoc, rarely communicating beforehand. Literature has shown that the medical community has deficiencies in communication and teamwork. However, we as medical providers do not know or understand the perceived barriers of our colleagues. Physicians may perceive a barrier that is different from nurses, respiratory therapists, pharmacists, or technicians. Perhaps we do not know in which area of teamwork and communication we are deficient. Only when we understand the perceptions of our fellow coworkers can we take steps toward improvement in quality resuscitations and therefore patient safety. The primary objectives of this study were to describe and understand the perceived barriers to effective communication and teamwork among different disciplines forming spontaneous resuscitation teams at a tertiary urban PED and to determine if providers of different disciplines perceived these barriers differently. This was a mixed-methods study conducted in a single, tertiary care freestanding children's hospital emergency department. Survey questions were iteratively developed to measure the construct of barriers and best practices within resuscitation teamwork, which was administered to staff among 5 selected roles: physicians, nurses, respiratory technicians, PED technicians, and PED pharmacists. It contained open-ended questions to provide statements on specific barriers or goals in effective teamwork, as well as a priority ranking on 25 different statements on teamwork extracted from the literature. From the participant data, 9 core themes related to resuscitation teamwork were coalesced using affinity diagramming by the authors. All statements from the survey were coded to the 9 core themes by 2 authors, with high reliability (κ = 0.93). Descriptive statistics were used to summarize the prevalence of themes mentioned by survey participants. A χ test was used to determine differences

Impact of ITER liquid metal design options on safety level and licensing - Sweden

International Nuclear Information System (INIS)

Harfors, C.; Devell, L.; Johansson, Kjell; Lundell, B.; Rolandsson, S.

1993-01-01

The safety level and licensability of five design options for ITER coolant, breeding material and structural material are assessed, with emphasis on some specified accident scenarios. The safety level is assessed in terms of barrier requirements and the feasibility to construct and qualify such a barrier. The licensability in Sweden of each design option is assessed based on the indicated safety level and on a judgement of the technical feasibility to construct and qualify the ITER tokamak itself, based on the selected design option. 20 refs

Neighborhood walking among overweight and obese adults: age variations in barriers and motivators.

Science.gov (United States)

Lee, Chanam; Ory, Marcia G; Yoon, Jeongjae; Forjuoh, Samuel N

2013-02-01

Walking is a popular form of physical activity that can bring many public health benefits. It can be even more beneficial to those who are currently obese or overweight. However, many barriers discourage people from walking, ranging from lack of motivation to unsafe neighborhood environments, and such barriers vary with age. This study addresses barriers and motivators to walking among overweight and obese adults, and examines their age variations. Particular emphasis was given to modifiable environmental factors as the priority intervention targets. A survey of 161 overweight and obese adults recruited from a large integrated healthcare system in central Texas provided data on walking, demographics, motivators and barriers. Descriptive statistics and correlation analysis were conducted. The respondents had a mean age of 48.4 (20-86), and were predominantly female (80.8%), non-Hispanic White (86.0%), and obese (mean BMI = 32.5). Popular environmental barriers to walking were: bad weather, inadequate lighting, no shade, unattended dogs, disconnected sidewalks, poor walking surfaces, no interesting places to walk nearby, and no benches (74.5-38.5%). Even and smooth walking surfaces and benches were more frequently reported by older adults as motivators. Proximity to recreational facilities was a stronger motivator for younger adults. Two safety related barriers, fear of injury (older adults) and traffic safety concerns (younger adults), also showed significant age differences. Overweight and obese adults experience substantial environmental barriers to walking, but many of them are modifiable. Observed age variations suggest that future interventions may be more effective if tailored to address age-specific barriers.

Exploring the QCD phase diagram through relativistic heavy ion collisions

Directory of Open Access Journals (Sweden)

Mohanty Bedangadas

2014-03-01

Full Text Available We present a review of the studies related to establishing the QCD phase diagram through high energy nucleus-nucleus collisions. We particularly focus on the experimental results related to the formation of a quark-gluon phase, crossover transition and search for a critical point in the QCD phase diagram.

Heuristic Diagrams as a Tool to Teach History of Science

Science.gov (United States)

Chamizo, Jose A.

2012-01-01

The graphic organizer called here heuristic diagram as an improvement of Gowin's Vee heuristic is proposed as a tool to teach history of science. Heuristic diagrams have the purpose of helping students (or teachers, or researchers) to understand their own research considering that asks and problem-solving are central to scientific activity. The…

Survey of systems safety analysis methods and their application to nuclear waste management systems

International Nuclear Information System (INIS)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study

Survey of systems safety analysis methods and their application to nuclear waste management systems

Energy Technology Data Exchange (ETDEWEB)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study.

Microsoft Visio 2013 business process diagramming and validation

CERN Document Server

Parker, David

2013-01-01

Microsoft Visio 2013 Business Process Diagramming and Validation provides a comprehensive and practical tutorial including example code and demonstrations for creating validation rules, writing ShapeSheet formulae, and much more.If you are a Microsoft Visio 2013 Professional Edition power user or developer who wants to get to grips with both the essential features of Visio 2013 and the validation rules in this edition, then this book is for you. A working knowledge of Microsoft Visio and optionally .NET for the add-on code is required, though previous knowledge of business process diagramming

Students’ understanding of forces: Force diagrams on horizontal and inclined plane

Science.gov (United States)

Sirait, J.; Hamdani; Mursyid, S.

2018-03-01

This study aims to analyse students’ difficulties in understanding force diagrams on horizontal surfaces and inclined planes. Physics education students (pre-service physics teachers) of Tanjungpura University, who had completed a Basic Physics course, took a Force concept test which has six questions covering three concepts: an object at rest, an object moving at constant speed, and an object moving at constant acceleration both on a horizontal surface and on an inclined plane. The test is in a multiple-choice format. It examines the ability of students to select appropriate force diagrams depending on the context. The results show that 44% of students have difficulties in solving the test (these students only could solve one or two items out of six items). About 50% of students faced difficulties finding the correct diagram of an object when it has constant speed and acceleration in both contexts. In general, students could only correctly identify 48% of the force diagrams on the test. The most difficult task for the students in terms was identifying the force diagram representing forces exerted on an object on in an inclined plane.

New requirements on safety of nuclear power plants according to the IAEA safety standards

International Nuclear Information System (INIS)

Misak, J.

2005-01-01

In this presentation author presents new requirements on safety of nuclear power plants according to the IAEA safety standards. It is concluded that: - New set of IAEA Safety Standards is close to completion: around 40 standards for NPPs; - Different interpretation of IAEA Safety Standards at present: best world practices instead of previous 'minimum common denominator'; - A number of safety improvements required for NPPs; - Requirements related to BDBAs and severe accidents are the most demanding due to degradation of barriers: hardware modifications and accident management; - Large variety between countries in implementation of accident management programmes: from minimum to major hardware modifications; -Distinction between existing and new NPPs is essential from the point of view of the requirements; WWER 440 reactors have potential to reflect IAEA Safety Standards for existing NPPs; relatively low reactor power offers broader possibilities

Diagrams: A Visual Survey of Graphs, Maps, Charts and Diagrams for the Graphic Designer.

Science.gov (United States)

Lockwood, Arthur

Since the ultimate success of any diagram rests in its clarity, it is important that the designer select a method of presentation which will achieve this aim. He should be aware of the various ways in which statistics can be shown diagrammatically, how information can be incorporated in maps, and how events can be plotted in chart or graph form.…

Interactive Cost Configuration Over Decision Diagrams

DEFF Research Database (Denmark)

Andersen, Henrik Reif; Hadzic, Tarik; Pisinger, David

2010-01-01

interaction online. In particular,binary decision diagrams (BDDs) have been successfully used as a compilation target for product and service configuration. In this paper we discuss how to extend BDD-based configuration to scenarios involving cost functions which express user preferences. We first show...... that an efficient, robust and easy to implement extension is possible if the cost function is additive, and feasible solutions are represented using multi-valued decision diagrams (MDDs). We also discuss the effect on MDD size if the cost function is non-additive or if it is encoded explicitly into MDD. We...... then discuss interactive configuration in the presence of multiple cost functions. We prove that even in its simplest form, multiple-cost configuration is NP-hard in the input MDD. However, for solving two-cost configuration we develop a pseudo-polynomial scheme and a fully polynomial approximation scheme...

TEP process flow diagram

Energy Technology Data Exchange (ETDEWEB)