Surface Movement Incidents Reported to the NASA Aviation Safety Reporting System

Science.gov (United States)

Connell, Linda J.; Hubener, Simone

1997-01-01

Increasing numbers of aircraft are operating on the surface of airports throughout the world. Airport operations are forecast to grow by more that 50%, by the year 2005. Airport surface movement traffic would therefore be expected to become increasingly congested. Safety of these surface operations will become a focus as airport capacity planning efforts proceed toward the future. Several past events highlight the prevailing risks experienced while moving aircraft during ground operations on runways, taxiways, and other areas at terminal, gates, and ramps. The 1994 St. Louis accident between a taxiing Cessna crossing an active runway and colliding with a landing MD-80 emphasizes the importance of a fail-safe system for airport operations. The following study explores reports of incidents occurring on an airport surface that did not escalate to an accident event. The Aviation Safety Reporting System has collected data on surface movement incidents since 1976. This study sampled the reporting data from June, 1993 through June, 1994. The coding of the data was accomplished in several categories. The categories include location of airport, phase of ground operation, weather /lighting conditions, ground conflicts, flight crew characteristics, human factor considerations, and airport environment. These comparisons and distributions of variables contributing to surface movement incidents can be invaluable to future airport planning, accident prevention efforts, and system-wide improvements.

Report of safety of the characterizing system of radioactive waste

International Nuclear Information System (INIS)

Angeles C, A.; Jimenez D, J.; Reyes L, J.

1998-09-01

Report of safety of the system of radioactive waste of the ININ: Installation, participant personnel, selection of the place, description of the installation, equipment. Proposed activities: operations with radioactive material, calibration in energy, calibration in efficiency, types of waste. Maintenance: handling of radioactive waste, physical safety. Organization: radiological protection, armor-plating, personal dosemeter, risks and emergency plan, environmental impact, medical exams. (Author)

Reporter Concerns in 300 Mode-Related Incident Reports from NASA's Aviation Safety Reporting System

Science.gov (United States)

McGreevy, Michael W.

1996-01-01

A model has been developed which represents prominent reporter concerns expressed in the narratives of 300 mode-related incident reports from NASA's Aviation Safety Reporting System (ASRS). The model objectively quantifies the structure of concerns which persist across situations and reporters. These concerns are described and illustrated using verbatim sentences from the original narratives. Report accession numbers are included with each sentence so that concerns can be traced back to the original reports. The results also include an inventory of mode names mentioned in the narratives, and a comparison of individual and joint concerns. The method is based on a proximity-weighted co-occurrence metric and object-oriented complexity reduction.

Using a quantitative risk register to promote learning from a patient safety reporting system.

Science.gov (United States)

Mansfield, James G; Caplan, Robert A; Campos, John S; Dreis, David F; Furman, Cathie

2015-02-01

Patient safety reporting systems are now used in most health care delivery organizations. These systems, such as the one in use at Virginia Mason (Seattle) since 2002, can provide valuable reports of risk and harm from the front lines of patient care. In response to the challenge of how to quantify and prioritize safety opportunities, a risk register system was developed and implemented. Basic risk register concepts were refined to provide a systematic way to understand risks reported by staff. The risk register uses a comprehensive taxonomy of patient risk and algorithmically assigns each patient safety report to 1 of 27 risk categories in three major domains (Evaluation, Treatment, and Critical Interactions). For each category, a composite score was calculated on the basis of event rate, harm, and cost. The composite scores were used to identify the "top five" risk categories, and patient safety reports in these categories were analyzed in greater depth to find recurrent patterns of risk and associated opportunities for improvement. The top five categories of risk were easy to identify and had distinctive "profiles" of rate, harm, and cost. The ability to categorize and rank risks across multiple dimensions yielded insights not previously available. These results were shared with leadership and served as input for planning quality and safety initiatives. This approach provided actionable input for the strategic planning process, while at the same time strengthening the Virginia Mason culture of safety. The quantitative patient safety risk register serves as one solution to the challenge of extracting valuable safety lessons from large numbers of incident reports and could profitably be adopted by other organizations.

Integrated care: an Information Model for Patient Safety and Vigilance Reporting Systems.

Science.gov (United States)

Rodrigues, Jean-Marie; Schulz, Stefan; Souvignet, Julien

2015-01-01

Quality management information systems for safety as a whole or for specific vigilances share the same information types but are not interoperable. An international initiative tries to develop an integrated information model for patient safety and vigilance reporting to support a global approach of heath care quality.

LOFT integral test system final safety analysis report

International Nuclear Information System (INIS)

1974-03-01

Safety analyses are presented for the following LOFT Reactor systems: engineering safety features; support buildings and facilities; instrumentation and controls; electrical systems; and auxiliary systems. (JWR)

Safety system function trends

International Nuclear Information System (INIS)

Johnson, C.

1989-01-01

This paper describes research to develop risk-based indicators of plant safety performance. One measure of the safety-performance of operating nuclear power plants is the unavailability of important safety systems. Brookhaven National Laboratory and Science Applications International Corporation are evaluating ways to aggregate train-level or component-level data to provide such an indicator. This type of indicator would respond to changes in plant safety margins faster than the currently used indicator of safety system unavailability (i.e., safety system failures reported in licensee event reports). Trends in the proposed indicator would be one indication of trends in plant safety performance and maintenance effectiveness. This paper summarizes the basis for such an indicator, identifies technical issues to be resolved, and illustrates the potential usefullness of such indicators by means of computer simulations and case studies

Replacement cross-site transfer system project W-058 safety class upgrade summary report

International Nuclear Information System (INIS)

Schlosser, R.L.

1998-01-01

This report evaluates the design of the replacement cross-site transfer system structures, systems, and components for safety related applications as defined in the Tank Waste Remediation Systems Basis for Interim Operations

The elements of a commercial human spaceflight safety reporting system

Science.gov (United States)

Christensen, Ian

2017-10-01

In its report on the SpaceShipTwo accident the National Transportation Safety Board (NTSB) included in its recommendations that the Federal Aviation Administration (FAA) ;in collaboration with the commercial spaceflight industry, continue work to implement a database of lessons learned from commercial space mishap investigations and encourage commercial space industry members to voluntarily submit lessons learned.; In its official response to the NTSB the FAA supported this recommendation and indicated it has initiated an iterative process to put into place a framework for a cooperative safety data sharing process including the sharing of lessons learned, and trends analysis. Such a framework is an important element of an overall commercial human spaceflight safety system.

Can Patient Safety Incident Reports Be Used to Compare Hospital Safety? Results from a Quantitative Analysis of the English National Reporting and Learning System Data.

Science.gov (United States)

Howell, Ann-Marie; Burns, Elaine M; Bouras, George; Donaldson, Liam J; Athanasiou, Thanos; Darzi, Ara

2015-01-01

The National Reporting and Learning System (NRLS) collects reports about patient safety incidents in England. Government regulators use NRLS data to assess the safety of hospitals. This study aims to examine whether annual hospital incident reporting rates can be used as a surrogate indicator of individual hospital safety. Secondly assesses which hospital characteristics are correlated with high incident reporting rates and whether a high reporting hospital is safer than those lower reporting hospitals. Finally, it assesses which health-care professionals report more incidents of patient harm, which report more near miss incidents and what hospital factors encourage reporting. These findings may suggest methods for increasing the utility of reporting systems. This study used a mix methods approach for assessing NRLS data. The data were investigated using Pareto analysis and regression models to establish which patients are most vulnerable to reported harm. Hospital factors were correlated with institutional reporting rates over one year to examine what factors influenced reporting. Staff survey findings regarding hospital safety culture were correlated with reported rates of incidents causing harm; no harm and death to understand what barriers influence error disclosure. 5,879,954 incident reports were collected from acute hospitals over the decade. 70.3% of incidents produced no harm to the patient and 0.9% were judged by the reporter to have caused severe harm or death. Obstetrics and Gynaecology reported the most no harm events [OR 1.61(95%CI: 1.12 to 2.27), p<0.01] and pharmacy was the hospital location where most near-misses were captured [OR 3.03(95%CI: 2.04 to 4.55), p<0.01]. Clinicians were significantly more likely to report death than other staff [OR 3.04(95%CI: 2.43 to 3.80) p<0.01]. A higher ratio of clinicians to beds correlated with reduced rate of harm reported [RR = -1.78(95%Cl: -3.33 to -0.23), p = 0.03]. Litigation claims per bed were

Lessons learnt from the development of the Patient Safety Incidents Reporting an Learning System for the Spanish National Health System: SiNASP.

Science.gov (United States)

Vallejo-Gutiérrez, Paula; Bañeres-Amella, Joaquim; Sierra, Eduardo; Casal, Jesús; Agra, Yolanda

2014-01-01

To describe the development process and characteristics of a patient safety incidents reporting system to be implemented in the Spanish National Health System, based on the context and the needs of the different stakeholders. Literature review and analysis of most relevant reporting systems, identification of more than 100 stakeholder's (patients, professionals, regional governments representatives) expectations and requirements, analysis of the legal context, consensus of taxonomy, development of the software and pilot test. Patient Safety Events Reporting and Learning system (Sistema de Notificación y Aprendizajepara la Seguridad del Paciente, SiNASP) is a generic reporting system for all types of incidents related to patient safety, voluntary, confidential, non punitive, anonymous or nominative with anonimization, system oriented, with local analysis of cases and based on the WHO International Classification for Patient Safety. The electronic program has an on-line form for reporting, a software to manage the incidents and improvement plans, and a scoreboard with process indicators to monitor the system. The reporting system has been designed to respond to the needs and expectations identified by the stakeholders, taking into account the lessons learned from the previous notification systems, the characteristics of the National Health System and the existing legal context. The development process presented and the characteristics of the system provide a comprehensive framework that can be used for future deployments of similar patient safety systems. Copyright © 2013 SECA. Published by Elsevier Espana. All rights reserved.

IAEA/NEA incident reporting system (IRS). Reporting guidelines. Feedback from safety related operating experience for nuclear power plants

International Nuclear Information System (INIS)

1998-01-01

The Incident Reporting System (IRS) is an international system jointly operated by the International Atomic Energy Agency (IAEA) and the Nuclear Energy Agency of the Organisation for Economic Cooperation and Development (OECD/NEA). The fundamental objective of the IRS is to contribute to improving the safety of commercial nuclear power plants (NPPs) which are operated worldwide. This objective can be achieved by providing timely and detailed information on both technical and human factors related to events of safety significance which occur at these plants. The purpose of these guidelines, which supersede the previous IAEA Safety Series No. 93 (Part II) and the NEA IRS guidelines, is to describe the system and to give users the necessary background and guidance to enable them to produce IRS reports meeting a high standard of quality while retaining the high efficiency of the system expected by all Member States operating nuclear power plants. These guidelines have been jointly developed and approved by the NEA/IAEA

Barriers to Implementing a Reporting and Learning Patient Safety System: Pediatric Chiropractic Perspective.

Science.gov (United States)

Pohlman, Katherine A; Carroll, Linda; Hartling, Lisa; Tsuyuki, Ross T; Vohra, Sunita

2016-04-01

A reporting and learning system is a method of monitoring the occurrence of incidents that affect patient safety. This cross-sectional survey asked pediatric chiropractors about factors that may limit their participation in such a system. The list of potential barriers for participation was developed using a systematic approach. All members of the 2 pediatric councils associated with US national chiropractic organizations were invited to complete the survey (N = 400). The cross-sectional survey was created using an online survey tool (REDCap) and sent directly to member emails addressed by the respective executive committees. Of the 400 potential respondents, 81 responded (20.3%). The most common limitations to participating were identified as time pressure (96%) and patient concerns (81%). Reporting and learning systems have been utilized to increase safety awareness in many high-risk industries. To be successful, future patient safety studies with pediatric chiropractors need to ensure these barriers are understood and addressed. © The Author(s) 2015.

Safety analysis report 231-Z Building

Energy Technology Data Exchange (ETDEWEB)

Powers, C.S.

1989-03-01

This report provides an intensive review of the nuclear safety of the operation of the 231-Z Building. For background information complete descriptions of the floor plan, building services, alarm systems, and glove box systems are included in this report. In addition, references are included to The Plutonium Laboratory Radiation Work Procedures, Safety Guides, 231-Z Operating Procedures Manual and Nuclear Materials accountability Procedures. Engineered and administrative features contribute to the overall safety of personnel, the building, and environs. The consequences of credible incidents were considered and are discussed.

Model for safety reports including descriptive examples

International Nuclear Information System (INIS)

1995-12-01

Several safety reports will be produced in the process of planning and constructing the system for disposal of high-level radioactive waste in Sweden. The present report gives a model, with detailed examples, of how these reports should be organized and what steps they should include. In the near future safety reports will deal with the encapsulation plant and the repository. Later reports will treat operation of the handling systems and the repository

Progress report: 1996 Radiation Safety Systems Division

International Nuclear Information System (INIS)

Bhagwat, A.M.; Sharma, D.N.; Abani, M.C.; Mehta, S.K.

1997-01-01

The activities of Radiation Safety Systems Division include (i) development of specialised monitoring systems and radiation safety information network, (ii) radiation hazards control at the nuclear fuel cycle facilities, the radioisotope programmes at Bhabha Atomic Research Centre (BARC) and for the accelerators programme at BARC and Centre for Advanced Technology (CAT), Indore. The systems on which development and upgradation work was carried out during the year included aerial gamma spectrometer, automated environment monitor using railway network, radioisotope package monitor and air monitors for tritium and alpha active aerosols. Other R and D efforts at the division included assessment of risk for radiation exposures and evaluation of ICRP 60 recommendations in the Indian context, shielding evaluation and dosimetry for the new upcoming accelerator facilities and solid state nuclear track detector techniques for neutron measurements. The expertise of the divisional members was provided for 36 safety committees of BARC and Atomic Energy Regulatory Board (AERB). Twenty three publications were brought out during the year 1996. (author)

Annual report on reactor safety research projects. Reporting period 2011. Progress report

International Nuclear Information System (INIS)

2011-01-01

Within its competence for energy research the Federal Ministry of Economics and Technology (BMWi) sponsors research projects on the safety of nuclear power plants currently in operation. The objective of these projects is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS)mbH, by order of the BMWi, continuously issues information on the status of such research projects by publishing semi-annual and annual progress reports within the series of GRSF- Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the research organisations themselves as documentation of their progress in work. The progress reports are published by the Project Management Agency/Authority Support Division of GRS. The reports as of the year 2000 are available in the Internet-based information system on results and data of reactor safety research (http://www.grs-fbw.de). The compilation of the reports is classified according to the classification system ''Joint Safety Research Index (JSRI)''. The reports are arranged in sequence of their project numbers. It has to be pointed out that the authors of the reports are responsible for the contents of this compilation. The BMWi does not take any responsibility for the correctness, exactness and completeness of the information nor for the observance of private claims of third parties. (orig.)

Annual report on reactor safety research projects. Reporting period 2014. Progress report

Energy Technology Data Exchange (ETDEWEB)

NONE

2014-07-01

Within its competence for energy research the Federal Ministry for Economic Affairs and Energy (BMWi) sponsors research projects on the safety of nuclear power plants currently in operation. The objective of these projects is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, by order of the BMWi, continuously issues information on the status of such research projects by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the research organisations themselves as documentation of their progress in work. The progress reports are published by the Project Management Agency/Authority Support Division of GRS. The reports as of the year 2000 are available in the lnternet-based information system on results and data of reactor safety research (http://www.grs-fbw.de). The compilation of the reports is classified according to the classification system ''Joint Safety Research Index (JSRI)''. The reports are arranged in sequence of their project numbers. lt has to be pointed out that the authors of the reports are responsible for the contents of this compilation. The BMWi does not take any responsibility for the correctness, exactness and completeness of the information nor for the observance of private claims of third parties.

Annual report on reactor safety research projects. Reporting period 2013. Progress report

International Nuclear Information System (INIS)

2013-01-01

Within its competence for energy research the Federal Ministry of Economics and Technology (BMWi) sponsors research projects on the safety of nuclear power plants currently in operation. The objective of these projects is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS)mbH, by order of the BMWi, continuously issues information on the status of such research projects by publishing semi-annual and annual progress reports within the series of GRSF- Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the research organisations themselves as documentation of their progress in work. The progress reports are published by the Project Management Agency/Authority Support Division of GRS. The reports as of the year 2000 are available in the Internet-based information system on results and data of reactor safety research (http://www.grs-fbw.de). The compilation of the reports is classified according to the classification system ''Joint Safety Research Index (JSRI)''. The reports are arranged in sequence of their project numbers. It has to be pointed out that the authors of the reports are responsible for the contents of this compilation. The BMWi does not take any responsibility for the correctness, exactness and completeness of the information nor for the observance of private claims of third parties. (orig.)

Annual report on reactor safety research projects. Reporting period 2015. Progress report

International Nuclear Information System (INIS)

2015-01-01

Within its competence for energy research the Federal Ministry for Economic Affairs and Energy (BMWi) sponsors research projects on the safety of nuclear power plants currently in operation. The objective of these projects is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft tor Anlagen- und Reaktorsicherheit (GRS) gGmbH, by order of the BMWi, continuously issues information on the status of such research projects by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are ·' prepared in a standard form by the research organisations themselves as documentation of their progress in work. The progress reports are published by the Project Management Agency/Authority Support Division of GRS. The reports as of the year 2000 are available in the lnternet-based information system on results and data of reactor safety research (http://www.grs-fbw.de). The compilation of the reports is classified according to the classification system ''Joint Safety Research Index (JSRI)''. The reports are arranged in sequence of their project numbers. it has to be pointed out that the authors of the reports are responsible for the contents of this compilation. The BMWi does not take any responsibility for the correctness, exactness and completeness of the information nor for the observance of private claims of third parties.

Safety analysis report for packaging (onsite) sample pig transport system

International Nuclear Information System (INIS)

MCCOY, J.C.

1999-01-01

This Safety Analysis Report for Packaging (SARP) provides a technical evaluation of the Sample Pig Transport System as compared to the requirements of the U.S. Department of Energy, Richland Operations Office (RL) Order 5480.1, Change 1, Chapter III. The evaluation concludes that the package is acceptable for the onsite transport of Type B, fissile excepted radioactive materials when used in accordance with this document

Safety analysis report for packaging (onsite) sample pig transport system

Energy Technology Data Exchange (ETDEWEB)

MCCOY, J.C.

1999-03-16

This Safety Analysis Report for Packaging (SARP) provides a technical evaluation of the Sample Pig Transport System as compared to the requirements of the U.S. Department of Energy, Richland Operations Office (RL) Order 5480.1, Change 1, Chapter III. The evaluation concludes that the package is acceptable for the onsite transport of Type B, fissile excepted radioactive materials when used in accordance with this document.

Safety analysis report for packaging (onsite) doorstop samplecarrier system

Energy Technology Data Exchange (ETDEWEB)

Obrien, J.H.

1997-02-24

The Doorstop Sample Carrier System consists of a Type B certified N-55 overpack, U.S. Department of Transportation (DOT) specification or performance-oriented 208-L (55-gal) drum (DOT 208-L drum), and Doorstop containers. The purpose of the Doorstop Sample Carrier System is to transport samples onsite for characterization. This safety analysis report for packaging (SARP) provides the analyses and evaluation necessary to demonstrate that the Doorstop Sample Carrier System meets the requirements and acceptance criteria for both Hanford Site normal transport conditions and accident condition events for a Type B package. This SARP also establishes operational, acceptance, maintenance, and quality assurance (QA) guidelines to ensure that the method of transport for the Doorstop Sample Carrier System is performed safely in accordance with WHC-CM-2-14, Hazardous Material Packaging and Shipping.

78 FR 71036 - Pipeline Safety: Random Drug Testing Rate; Contractor Management Information System Reporting...

Science.gov (United States)

2013-11-27

... PHMSA-2013-0248] Pipeline Safety: Random Drug Testing Rate; Contractor Management Information System Reporting; and Obtaining Drug and Alcohol Management Information System Sign-In Information AGENCY: Pipeline... Management Information System (MIS) Data; and New Method for Operators to Obtain User Name and Password for...

Safety Basis Report

International Nuclear Information System (INIS)

R.J. Garrett

2002-01-01

As part of the internal Integrated Safety Management Assessment verification process, it was determined that there was a lack of documentation that summarizes the safety basis of the current Yucca Mountain Project (YMP) site characterization activities. It was noted that a safety basis would make it possible to establish a technically justifiable graded approach to the implementation of the requirements identified in the Standards/Requirements Identification Document. The Standards/Requirements Identification Documents commit a facility to compliance with specific requirements and, together with the hazard baseline documentation, provide a technical basis for ensuring that the public and workers are protected. This Safety Basis Report has been developed to establish and document the safety basis of the current site characterization activities, establish and document the hazard baseline, and provide the technical basis for identifying structures, systems, and components (SSCs) that perform functions necessary to protect the public, the worker, and the environment from hazards unique to the YMP site characterization activities. This technical basis for identifying SSCs serves as a grading process for the implementation of programs such as Conduct of Operations (DOE Order 5480.19) and the Suspect/Counterfeit Items Program. In addition, this report provides a consolidated summary of the hazards analyses processes developed to support the design, construction, and operation of the YMP site characterization facilities and, therefore, provides a tool for evaluating the safety impacts of changes to the design and operation of the YMP site characterization activities

Safety Basis Report

Energy Technology Data Exchange (ETDEWEB)

R.J. Garrett

2002-01-14

As part of the internal Integrated Safety Management Assessment verification process, it was determined that there was a lack of documentation that summarizes the safety basis of the current Yucca Mountain Project (YMP) site characterization activities. It was noted that a safety basis would make it possible to establish a technically justifiable graded approach to the implementation of the requirements identified in the Standards/Requirements Identification Document. The Standards/Requirements Identification Documents commit a facility to compliance with specific requirements and, together with the hazard baseline documentation, provide a technical basis for ensuring that the public and workers are protected. This Safety Basis Report has been developed to establish and document the safety basis of the current site characterization activities, establish and document the hazard baseline, and provide the technical basis for identifying structures, systems, and components (SSCs) that perform functions necessary to protect the public, the worker, and the environment from hazards unique to the YMP site characterization activities. This technical basis for identifying SSCs serves as a grading process for the implementation of programs such as Conduct of Operations (DOE Order 5480.19) and the Suspect/Counterfeit Items Program. In addition, this report provides a consolidated summary of the hazards analyses processes developed to support the design, construction, and operation of the YMP site characterization facilities and, therefore, provides a tool for evaluating the safety impacts of changes to the design and operation of the YMP site characterization activities.

Supplement to safety analysis report. 306-W building operations safety requirement

International Nuclear Information System (INIS)

Richey, C.R.

1979-08-01

The operations safety requirements (OSRs) presented in this report define the conditions, safe boundaries, and management control needed for safely conducting operations with radioactive materials in the Pacific Northwest Laboratory (PNL) 306-W building. The safety requirements are organized in five sections. Safety limits are safety-related process variables that are observable and measurable. Limiting conditions cover: equipment and technical conditions and characteristics of the facility and operations necessary for continued safe operation. Surveillance requirements prescribe the requirements for checking systems and components that are essential to safety. Equipment design controls require that changes to process equipment and systems be independently checked and approved to assure that the changes will have no adverse effect on safety. Administrative controls describe and discuss the organization and administrative systems and procedures to be used for safe operation of the facility. Details of the implementation of the operations safety requirements are prescribed by internal PNL documents such as criticality safety specifications and radiation work procedures

Safety system status monitoring

International Nuclear Information System (INIS)

Lewis, J.R.; Morgenstern, M.H.; Rideout, T.H.; Cowley, P.J.

1984-03-01

The Pacific Northwest Laboratory has studied the safety aspects of monitoring the preoperational status of safety systems in nuclear power plants. The goals of the study were to assess for the NRC the effectiveness of current monitoring systems and procedures, to develop near-term guidelines for reducing human errors associated with monitoring safety system status, and to recommend a regulatory position on this issue. A review of safety system status monitoring practices indicated that current systems and procedures do not adequately aid control room operators in monitoring safety system status. This is true even of some systems and procedures installed to meet existing regulatory guidelines (Regulatory Guide 1.47). In consequence, this report suggests acceptance criteria for meeting the functional requirements of an adequate system for monitoring safety system status. Also suggested are near-term guidelines that could reduce the likelihood of human errors in specific, high-priority status monitoring tasks. It is recommended that (1) Regulatory Guide 1.47 be revised to address these acceptance criteria, and (2) the revised Regulatory Guide 1.47 be applied to all plants, including those built since the issuance of the original Regulatory Guide

Safety system status monitoring

Energy Technology Data Exchange (ETDEWEB)

Lewis, J.R.; Morgenstern, M.H.; Rideout, T.H.; Cowley, P.J.

1984-03-01

The Pacific Northwest Laboratory has studied the safety aspects of monitoring the preoperational status of safety systems in nuclear power plants. The goals of the study were to assess for the NRC the effectiveness of current monitoring systems and procedures, to develop near-term guidelines for reducing human errors associated with monitoring safety system status, and to recommend a regulatory position on this issue. A review of safety system status monitoring practices indicated that current systems and procedures do not adequately aid control room operators in monitoring safety system status. This is true even of some systems and procedures installed to meet existing regulatory guidelines (Regulatory Guide 1.47). In consequence, this report suggests acceptance criteria for meeting the functional requirements of an adequate system for monitoring safety system status. Also suggested are near-term guidelines that could reduce the likelihood of human errors in specific, high-priority status monitoring tasks. It is recommended that (1) Regulatory Guide 1.47 be revised to address these acceptance criteria, and (2) the revised Regulatory Guide 1.47 be applied to all plants, including those built since the issuance of the original Regulatory Guide.

Safety Test Report for the SNF Dry Storage System

Energy Technology Data Exchange (ETDEWEB)

Bang, K. S.; Seo, K. S.; Lee, J. H.; Lee, J. C.; Choi, W. S

2008-11-15

This is technical report conducted by KAERI under the contract with NETEC for safety test for the PWR S/F dry storage system. Leak Test was performed after drop test and turn-over test, the measured leakage rate was lower than allowable leakage rate. It is revealed that the containment integrity of the dry storage system is maintained. In the seismic test, the moving of the model was measured at SRTH seismic response of 0.4 g and 0.8 g. Therefore the seismic test results can be used fully to the test data for verification of the seismic analysis. In the thermal test, the direction of the inlet and outlet of the air has no effect on the heat transfer performance. The passive heat removal system of the horizontal storage module was designed well.

Systems Analysis of NASA Aviation Safety Program: Final Report

Science.gov (United States)

Jones, Sharon M.; Reveley, Mary S.; Withrow, Colleen A.; Evans, Joni K.; Barr, Lawrence; Leone, Karen

2013-01-01

A three-month study (February to April 2010) of the NASA Aviation Safety (AvSafe) program was conducted. This study comprised three components: (1) a statistical analysis of currently available civilian subsonic aircraft data from the National Transportation Safety Board (NTSB), the Federal Aviation Administration (FAA), and the Aviation Safety Information Analysis and Sharing (ASIAS) system to identify any significant or overlooked aviation safety issues; (2) a high-level qualitative identification of future safety risks, with an assessment of the potential impact of the NASA AvSafe research on the National Airspace System (NAS) based on these risks; and (3) a detailed, top-down analysis of the NASA AvSafe program using an established and peer-reviewed systems analysis methodology. The statistical analysis identified the top aviation "tall poles" based on NTSB accident and FAA incident data from 1997 to 2006. A separate examination of medical helicopter accidents in the United States was also conducted. Multiple external sources were used to develop a compilation of ten "tall poles" in future safety issues/risks. The top-down analysis of the AvSafe was conducted by using a modification of the Gibson methodology. Of the 17 challenging safety issues that were identified, 11 were directly addressed by the AvSafe program research portfolio.

Radiation safety systems at the NSLS

International Nuclear Information System (INIS)

Dickinson, T.

1987-04-01

This report describes design principles that were used to establish the radiation safety systems at the National Synchrotron Light Source. The author described existing safety systems and the history of partial system failures. 1 fig

Template for safety reports with descriptive example

International Nuclear Information System (INIS)

1995-12-01

This report provides a template for future safety reports on long-term safety in support of important decisions and permit applications in connection with the construction of a deep repository system. The template aims at providing a uniform structure for describing long-term safety, after the repository has been closed and sealed. The availability of such a structure will simplify both preparation and review of the safety reports, and make it possible to follow how safety assessments are influenced by the progressively more detailed body of data that emerges. A separate section containing 'descriptive examples' has been appended to the template. This section illustrates what the different chapters of the template should contain. 279 refs

Template for safety reports with descriptive example

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

This report provides a template for future safety reports on long-term safety in support of important decisions and permit applications in connection with the construction of a deep repository system. The template aims at providing a uniform structure for describing long-term safety, after the repository has been closed and sealed. The availability of such a structure will simplify both preparation and review of the safety reports, and make it possible to follow how safety assessments are influenced by the progressively more detailed body of data that emerges. A separate section containing `descriptive examples` has been appended to the template. This section illustrates what the different chapters of the template should contain. 279 refs.

Considerations on nuclear reactor passive safety systems

International Nuclear Information System (INIS)

2016-01-01

After having indicated some passive safety systems present in electronuclear reactors (control bars, safety injection system accumulators, reactor cooling after stoppage, hydrogen recombination systems), this report recalls the main characteristics of passive safety systems, and discusses the main issues associated with the assessment of new passive systems (notably to face a sustained loss of electric supply systems or of cold water source) and research axis to be developed in this respect. More precisely, the report comments the classification of safety passive systems as it is proposed by the IAEA, outlines and comments specific aspects of these systems regarding their operation and performance. The next part discusses the safety approach, the control of performance of safety passive systems, issues related to their reliability, and the expected contribution of R and D (for example: understanding of physical phenomena which have an influence of these systems, capacities of simulation of these phenomena, needs of experimentations to validate simulation codes)

System and safety studies of accelerator driven transmutation. Annual Report 2003

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

System and safety studies of accelerator driven transmutation. Annual Report 2003

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Tucek, Kamil [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics] [and others

2004-12-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics reported here has been focused on different aspects of safety of the Accelerator-Driven Transmutation Systems and on Transmutation research in more general terms. An overview of the topics of our research is given in the Summary which is followed by detailed reports as separate chapters or subchapters. Some of the research topics reported in this report are referred to appendices, which have been published in the open literature. Topics, which are not yet published, are described with more details in the main part of this report. Main focus has been, as before, largely determined by the programme of the European projects of the 5th Framework Programme in which KTH is actively participating. In particular: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features. This activity includes even computer modeling of nuclear fuel production. Three different ADS-core concept are being investigated: Conceptual design of Pb-Bi cooled core with nitride fuel so called Sing-Sing Core developed at KTH; Pb-Bi cooled core with oxide fuel so called ANSALDO design for the European Project PDS-XADS; Gas cooled core with oxide fuel a design investigated for the European Project PDS-XADS. b) analysis of potential of advance fuels, in particular nitrides with high content of minor actinides; c) analysis of ADS-dynamics and assessment of major reactivity feedbacks; d) emergency heat removal from ADS; e) participation in ADS: MUSE (CEA-Cadarache), YALINA subcritical experiment in Minsk and designing of the subcritical experiment SAD in Dubna; f) theoretical and simulation studies of radiation damage in high neutron (and/or proton) fluxes; g) computer code and nuclear data development relevant for simulation and optimization of ADS, validation of the MCB code and sensitivity analysis; h) studies of

Idaho National Laboratory Integrated Safety Management System FY 2012 Effectiveness Review and Declaration Report

Energy Technology Data Exchange (ETDEWEB)

Farren Hunt

2012-12-01

Idaho National Laboratory (INL) performed an Annual Effectiveness Review of the Integrated Safety Management System (ISMS), per 48 Code of Federal Regulations (CFR) 970.5223 1, “Integration of Environment, Safety and Health into Work Planning and Execution.” The annual review assessed Integrated Safety Management (ISM) effectiveness, provided feedback to maintain system integrity, and identified target areas for focused improvements and assessments for fiscal year (FY) 2013. Results of the FY 2012 annual effectiveness review demonstrated that the INL’s ISMS program was significantly strengthened. Actions implemented by the INL demonstrate that the overall Integrated Safety Management System is sound and ensures safe and successful performance of work while protecting workers, the public, and environment. This report also provides several opportunities for improvement that will help further strengthen the ISM Program and the pursuit of safety excellence. Demonstrated leadership and commitment, continued surveillance, and dedicated resources have been instrumental in maturing a sound ISMS program. Based upon interviews with personnel, reviews of assurance activities, and analysis of ISMS process implementation, this effectiveness review concludes that ISM is institutionalized and is “Effective”.

Comprehensive Lifecycle for Assuring System Safety

Science.gov (United States)

Knight, John C.; Rowanhill, Jonathan C.

2017-01-01

CLASS is a novel approach to the enhancement of system safety in which the system safety case becomes the focus of safety engineering throughout the system lifecycle. CLASS also expands the role of the safety case across all phases of the system's lifetime, from concept formation to decommissioning. As CLASS has been developed, the concept has been generalized to a more comprehensive notion of assurance becoming the driving goal, where safety is an important special case. This report summarizes major aspects of CLASS and contains a bibliography of papers that provide additional details.

Nuclear Reactor RA Safety Report, Vol. 8, Auxiliary system

International Nuclear Information System (INIS)

1986-11-01

This volume describes RA reactor auxiliary systems, as follows: special ventilation system, special drainage system, hot cells, systems for internal transport. Ventilation system is considered as part of the reactor safety and protection system. Its role is eliminate possible radioactive particles dispersion in the environment. Special drainage system includes pipes and reservoirs with the safety role, meaning absorption or storage of possible radioactive waste water from the reactor building. Hot cells existing in the RA reactor building are designed for production of sealed radioactive sources, including packaging and transport [sr

Safety report on WWR-S reactor

International Nuclear Information System (INIS)

Horyna, J.; Kaisler, L.; Listik, E.

1981-04-01

The present Safety Report of the WWR-S reactor summarizes findings obtained during the trial and partially also permanent operation of the reactor after two stages of its reconstruction implemented between 1974 and 1976. Most data are presented necessary for assessing probable risks of possible accident conditions whose consequences pose health hazards to individuals of the population, radiation personnel and the facilities themselves. Attention is devoted to the description of the locality, to components and systems, heat removal from the core, design aspects, the quality of new and old parts of the technological circuits, the systems of protection and control, the emergency core cooling system, the problems of radiation safety, and to the safety analyses of the abnormal states envisaged. The Report was compiled with regard to IAEA and CMEA recommendations concerning safe operation of research reactors and to the recommendations and binding decisions of the Czechoslovak Atomic Energy Commission. (author)

Central Safety Department. Annual report 1986

International Nuclear Information System (INIS)

Kiefer, H.; Koenig, L.A.

1987-03-01

The Safety Officer and the Security Officer are responsible for radiation protection and technical safety, both conventional and nuclear, for the physical protection as well as the safeguards of nuclear materials and radioactive substances within the Kernforschungszentrum Karlsruhe GmbH (KfK). To fulfill these functions they rely on the assistance of the Central Safety Department. The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The r+d work concentrates on the following aspects: physical and chemical behavior of biologically particularly active radionuclides, behavior of HT in the air/plant/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. The report gives details of the different duties, indicates the results of 1986 routine tasks and reports about results of investigations and developments of the working groups of the Department. (orig.) [de

Generic safety evaluation report regarding integrity of BWR scram system piping

International Nuclear Information System (INIS)

1981-08-01

Safety concerns associated with postulated pipe breaks in the boiling water reactor (BWR) scram system were identified during the staff's continuing investigation of the Browns Ferry Unit 3 control rod partial insertion failure on June 28, 1980. This report includes an evaluation of the licensing basis for the BWR scram discharge volume (SDV) piping and an assessment of the potential for the SDV piping to fail while in service. A discussion of the means available for mitigation an unlikely SDV system failure is provided. Generic recommendations are made to improve mitigation capability and ensure that system integrity is maintained in service

Classification of Aeronautics System Health and Safety Documents

Data.gov (United States)

National Aeronautics and Space Administration — Most complex aerospace systems have many text reports on safety, maintenance, and associated issues. The Aviation Safety Reporting System (ASRS) spans several...

Central Safety Department, annual report 1987

International Nuclear Information System (INIS)

Kiefer, H.; Koenig, L.A.

1988-02-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The r+d work concentrates on the following aspects: physical and chemical behaviour of biologically particularly active radionuclides, behaviour of HT in the air/plan/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1987 routine tasks and reports about results of investigations and developments of the working groups of the Department. (orig./HP) [de

Program nuclear safety research: report 2000

International Nuclear Information System (INIS)

Muehl, B.

2001-09-01

The reactor safety R and D work of forschungszentrum karlsruhe (FZK) had been part of the nuclear safety research project (PSF) since 1990. In 2000, a new organisational structure was introduced and the Nuclear Safety Research Project was transferred into the nuclear safety research programme (NUKLEAR). In addition to the three traditional main topics - Light Water Reactor safety, Innovative systems, Studies related to the transmutation of actinides -, the new Programme NUKLEAR also covers Safety research related to final waste storage and Immobilisation of HAW. These new topics, however, will only be dealt with in the next annual report. Some tasks related to the traditional topics have been concluded and do no longer appear in the annual report; other tasks are new and are described for the first time. Numerous institutes of the research centre contribute to the work programme, as well as several external partners. The tasks are coordinated in agreement with internal and external working groups. The contributions to this report, which are either written in German or in English, correspond to the status of early/mid 2001. (orig.)

RB research reactor safety report; Izvestaj o sigurnsti istrazivackog reaktora RB

Energy Technology Data Exchange (ETDEWEB)

Sotic, O; Pesic, M; Vranic, S [Boris Kidric Institute of Nuclear Sciences Vinca, Beograd (Yugoslavia)

1979-04-15

This new version of the safety report is a revision of the safety report written in 1962 when the RB reactor started operation after reconstruction. The new safety report was needed because reactor systems and components have been improved and the administrative procedures were changed. the most important improvements and changes were concerned with the use of highly enriched fuel (80% enriched), construction of reactor converter outside the reactor vessel, improved control system by two measuring start-up channels, construction of system for heavy water leak detection, new inter phone connection between control room and other reactor rooms. This report includes description of reactor building with installations, rector vessel, reactor core, heavy water system, control system, safety system, dosimetry and alarm systems, experimental channels, neutron converter, reactor operation. Safety aspects contain analyses of accident reasons, method for preventing reactivity insertions, analyses of maximum hypothetical accidents for cores with natural uranium, 2% enriched and 80% enriched fuel elements. Influence of seismic events on the reactor safety and well as coupling between reactor and the converter are parts of this document.

Engineered safeguards and passive safety features (safety analysis detailed report no. 6)

Energy Technology Data Exchange (ETDEWEB)

1988-01-15

The Safety-Analysis Summary lists the reactor's safety aspects for passive and active prevention of severe accidents and mitigation of accident consequences, i.e., intrinsic and passive protections of the plant; intrinsic and passive protections of the core; inherent decay-heat removal systems; rapid-shutdown systems; four physical containment barriers. This report goes into further details regarding some of this aspects.

System and safety studies of accelerator driven transmutation systems. Annual report 1997

International Nuclear Information System (INIS)

Wallenius, J.; Carlsson, Johan; Gudowski, W.

1997-12-01

In November 1996, SKB started financing of the project ''System and safety studies of accelerator driven transmutation systems and development of a spallation target''. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1997

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Carlsson, Johan; Gudowski, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1997-12-01

In November 1996, SKB started financing of the project ``System and safety studies of accelerator driven transmutation systems and development of a spallation target``. The aim of the project was stated as: 1) Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. 2) Build up of competence regarding issues related to spallation targets development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration-experiment. In the present report, activities within the framework of the project performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1997, are accounted for. 13 refs, 6 figs.

System and safety studies of accelerator driven transmutation systems. Annual report 1999

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for

System and safety studies of accelerator driven transmutation systems. Annual report 1999

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Eriksson, Marcus; Carlsson, Johan; Seltborg, Per; Tucek, Kamil [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2000-05-01

In 1996, SKB commenced funding of the project 'System and safety studies of accelerator driven transmutation systems and development of a spallation target'. The aim of the project was stated as: Development of a complete code for simulation of transmutation processes in an accelerator driven system. Application of the code for analysis of neutron flux, transmutation rates, reactivity changes, toxicity and radiation damages in the transmutation core. Build up of competence regarding issues related to spallation targets, development of research activities regarding relevant material issues. Performing of basic experiments in order to investigate the adequacy of using the spallation. target as a neutron source for a transmutation system, and participation in the planning and implementation of an international demonstration experiment. In the present report, activities within and related to the framework of the project, performed at the department of Nuclear and Reactor Physics at the Royal Institute of Technology during 1999, are accounted for.

HTGR safety research program. Progress report, April--June 1975

International Nuclear Information System (INIS)

Kirk, W.L.

1975-09-01

Progress in HTGR safety research is reported under the following headings: fission product technology; primary coolant impurities; structural investigation; safety instrumentation and control systems; phenomena modeling and systems analysis. (JWR)

NPP Temelin safety analysis reports and PSA status

International Nuclear Information System (INIS)

Mlady, O.

1999-01-01

To enhance the safety level of Temelin NPP, recommendations of the international reviews were implemented into the design as well as into organization of the plant construction and preparation for operation. The safety assessment of these design changes has been integrated and reflected in the Safety Analysis Reports, which follow the internationally accepted guidelines. All safety analyses within Safety Analysis Reports were repeated carefully considering technical improvements and replacements to complement preliminary safety documentation. These analyses were performed by advanced western computer codes to the depth and in the structure required by western standards. The Temelin NPP followed a systematic approach in the functional design of the Reactor Protection System and related safety analyses. Modifications of reactor protection system increase defense in depth and facilitate demonstrating that LOCA and radiological limits are met for non-LOCA events. The rigorous safety analysis methodology provides assurance that LOCA and radiological limits are met. Established and accepted safety analysis methodology and accepted criteria were applied to Temelin NPP meeting US NRC and Czech Republic requirements. IAEA guidelines and recommendations

Hot Cell Facility (HCF) Safety Analysis Report

Energy Technology Data Exchange (ETDEWEB)

MITCHELL,GERRY W.; LONGLEY,SUSAN W.; PHILBIN,JEFFREY S.; MAHN,JEFFREY A.; BERRY,DONALD T.; SCHWERS,NORMAN F.; VANDERBEEK,THOMAS E.; NAEGELI,ROBERT E.

2000-11-01

This Safety Analysis Report (SAR) is prepared in compliance with the requirements of DOE Order 5480.23, Nuclear Safety Analysis Reports, and has been written to the format and content guide of DOE-STD-3009-94 Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Safety Analysis Reports. The Hot Cell Facility is a Hazard Category 2 nonreactor nuclear facility, and is operated by Sandia National Laboratories for the Department of Energy. This SAR provides a description of the HCF and its operations, an assessment of the hazards and potential accidents which may occur in the facility. The potential consequences and likelihood of these accidents are analyzed and described. Using the process and criteria described in DOE-STD-3009-94, safety-related structures, systems and components are identified, and the important safety functions of each SSC are described. Additionally, information which describes the safety management programs at SNL are described in ancillary chapters of the SAR.

Hot Cell Facility (HCF) Safety Analysis Report

International Nuclear Information System (INIS)

MITCHELL, GERRY W.; LONGLEY, SUSAN W.; PHILBIN, JEFFREY S.; MAHN, JEFFREY A.; BERRY, DONALD T.; SCHWERS, NORMAN F.; VANDERBEEK, THOMAS E.; NAEGELI, ROBERT E.

2000-01-01

This Safety Analysis Report (SAR) is prepared in compliance with the requirements of DOE Order 5480.23, Nuclear Safety Analysis Reports, and has been written to the format and content guide of DOE-STD-3009-94 Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Safety Analysis Reports. The Hot Cell Facility is a Hazard Category 2 nonreactor nuclear facility, and is operated by Sandia National Laboratories for the Department of Energy. This SAR provides a description of the HCF and its operations, an assessment of the hazards and potential accidents which may occur in the facility. The potential consequences and likelihood of these accidents are analyzed and described. Using the process and criteria described in DOE-STD-3009-94, safety-related structures, systems and components are identified, and the important safety functions of each SSC are described. Additionally, information which describes the safety management programs at SNL are described in ancillary chapters of the SAR

Idaho National Laboratory Integrated Safety Management System FY 2016 Effectiveness Review and Declaration Report

International Nuclear Information System (INIS)

Hunt, Farren J.

2016-01-01

Idaho National Laboratory's (INL's) Integrated Safety Management System (ISMS) effectiveness review of fiscal year (FY) 2016 shows that INL has integrated management programs and safety elements throughout the oversight and operational activities performed at INL. The significant maturity of Contractor Assurance System (CAS) processes, as demonstrated across INL's management systems and periodic reporting through the Management Review Meeting process, over the past two years has provided INL with current real-time understanding and knowledge pertaining to the health of the institution. INL's sustained excellence of the Integrated Safety and effective implementation of the Worker Safety and Health Program is also evidenced by other external validations and key indicators. In particular, external validations include VPP, ISO 14001, DOELAP accreditation, and key Laboratory level indicators such as ORPS (number, event frequency and severity); injury/illness indicators such as Days Away, Restricted and Transfer (DART) case rate, back & shoulder metric and open reporting indicators, demonstrate a continuous positive trend and therefore improved operational performance over the last few years. These indicators are also reflective of the Laboratory's overall organizational and safety culture improvement. Notably, there has also been a step change in ESH&Q Leadership actions that have been recognized both locally and complex-wide. Notwithstanding, Laboratory management continues to monitor and take action on lower level negative trends in numerous areas including: Conduct of Operations, Work Control, Work Site Analysis, Risk Assessment, LO/TO, Fire Protection, and Life Safety Systems, to mention a few. While the number of severe injury cases has decreased, as evidenced by the reduction in the DART case rate, the two hand injuries and the fire truck/ambulance accident were of particular concern. Aggressive actions continue in order to understand the causes and define actions

Idaho National Laboratory Integrated Safety Management System FY 2016 Effectiveness Review and Declaration Report

Energy Technology Data Exchange (ETDEWEB)

Hunt, Farren J. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2016-12-01

Idaho National Laboratory’s (INL’s) Integrated Safety Management System (ISMS) effectiveness review of fiscal year (FY) 2016 shows that INL has integrated management programs and safety elements throughout the oversight and operational activities performed at INL. The significant maturity of Contractor Assurance System (CAS) processes, as demonstrated across INL’s management systems and periodic reporting through the Management Review Meeting process, over the past two years has provided INL with current real-time understanding and knowledge pertaining to the health of the institution. INL’s sustained excellence of the Integrated Safety and effective implementation of the Worker Safety and Health Program is also evidenced by other external validations and key indicators. In particular, external validations include VPP, ISO 14001, DOELAP accreditation, and key Laboratory level indicators such as ORPS (number, event frequency and severity); injury/illness indicators such as Days Away, Restricted and Transfer (DART) case rate, back & shoulder metric and open reporting indicators, demonstrate a continuous positive trend and therefore improved operational performance over the last few years. These indicators are also reflective of the Laboratory’s overall organizational and safety culture improvement. Notably, there has also been a step change in ESH&Q Leadership actions that have been recognized both locally and complex-wide. Notwithstanding, Laboratory management continues to monitor and take action on lower level negative trends in numerous areas including: Conduct of Operations, Work Control, Work Site Analysis, Risk Assessment, LO/TO, Fire Protection, and Life Safety Systems, to mention a few. While the number of severe injury cases has decreased, as evidenced by the reduction in the DART case rate, the two hand injuries and the fire truck/ambulance accident were of particular concern. Aggressive actions continue in order to understand the causes and

HERBE final safety report; HERBE Finalni sigurnosni izvestaj

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-07-01

The Final safety report of HERBE system constructed at the RB reactor consists of 13 chapters, as follows. Chapter 0 includes a summary and the contents of the Final safety report, fundamental characteristics of the system and conclusion remarks, with the license agreement of the Safety Committee of the Boris Kidric Institute. Chapter 1 describes and analyzes the site of the HERBE system, including demography, topography, meteorology, hydrology, geology, seismicity, ecology. Chapter 3 covers technical characteristics of the system, Chapter 4 deals with safety analysis, Chapter 5 describes organisation of construction and preliminary operational testing of the system. Chapter 6 deals with organisation and program of test and regular operation, relevant procedures. Chapter 7 defines operational conditions and constraints, Chapter 8 and describe methods and means of radiation protection and radioactive materials management respectively. Chapter 10 contains a review of emergency plans, measures and procedures for nuclear accident protection. Chapters 11 and 12 are concerned with quality assurance program and physical protection of the HERBE system and related nuclear material.

Analysis of general aviation single-pilot IFR incident data obtained from the NASA Aviation Safety Reporting System

Science.gov (United States)

Bergeron, H. P.

1983-01-01

An analysis of incident data obtained from the NASA Aviation Safety Reporting System (ASRS) has been made to determine the problem areas in general aviation single-pilot IFR (SPIFR) operations. The Aviation Safety Reporting System data base is a compilation of voluntary reports of incidents from any person who has observed or been involved in an occurrence which was believed to have posed a threat to flight safety. This paper examines only those reported incidents specifically related to general aviation single-pilot IFR operations. The frequency of occurrence of factors related to the incidents was the criterion used to define significant problem areas and, hence, to suggest where research is needed. The data was cataloged into one of five major problem areas: (1) controller judgment and response problems, (2) pilot judgment and response problems, (3) air traffic control (ATC) intrafacility and interfacility conflicts, (4) ATC and pilot communication problems, and (5) IFR-VFR conflicts. In addition, several points common to all or most of the problems were observed and reported. These included human error, communications, procedures and rules, and work load.

International recommendations for national patient safety incident reporting systems: an expert Delphi consensus-building process.

Science.gov (United States)

Howell, Ann-Marie; Burns, Elaine M; Hull, Louise; Mayer, Erik; Sevdalis, Nick; Darzi, Ara

2017-02-01

Patient safety incident reporting systems (PSRS) have been established for over a decade, but uncertainty remains regarding the role that they can and ought to play in quantifying healthcare-related harm and improving care. To establish international, expert consensus on the purpose of PSRS regarding monitoring and learning from incidents and developing recommendations for their future role. After a scoping review of the literature, semi-structured interviews with experts in PSRS were conducted. Based on these findings, a survey-based questionnaire was developed and subsequently completed by a larger expert panel. Using a Delphi approach, consensus was reached regarding the ideal role of PSRSs. Recommendations for best practice were devised. Forty recommendations emerged from the Delphi procedure on the role and use of PSRS. Experts agreed reporting system should not be used as an epidemiological tool to monitor the rate of harm over time or to appraise the relative safety of hospitals. They agreed reporting is a valuable mechanism for identifying organisational safety needs. The benefit of a national system was clear with respect to medication error, device failures, hospital-acquired infections and never events as these problems often require solutions at a national level. Experts recommended training for senior healthcare professionals in incident investigation. Consensus recommendation was for hospitals to take responsibility for creating safety solutions locally that could be shared nationally. We obtained reasonable consensus among experts on aims and specifications of PSRS. This information can be used to reflect on existing and future PSRS, and their role within the wider patient safety landscape. The role of PSRS as instruments for learning needs to be elaborated and developed further internationally. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

RPP-PRT-58489, Revision 1, One Systems Consistent Safety Analysis Methodologies Report. 24590-WTP-RPT-MGT-15-014

Energy Technology Data Exchange (ETDEWEB)

Gupta, Mukesh [URS Professional Solutions LLC, Aiken, SC (United States); Niemi, Belinda [Washington River Protection Solutions, LLC, Richland, WA (United States); Paik, Ingle [Washington River Protection Solutions, LLC, Richland, WA (United States)

2015-09-02

In 2012, One System Nuclear Safety performed a comparison of the safety bases for the Tank Farms Operations Contractor (TOC) and Hanford Tank Waste Treatment and Immobilization Plant (WTP) (RPP-RPT-53222 / 24590-WTP-RPT-MGT-12-018, “One System Report of Comparative Evaluation of Safety Bases for Hanford Waste Treatment and Immobilization Plant Project and Tank Operations Contract”), and identified 25 recommendations that required further evaluation for consensus disposition. This report documents ten NSSC approved consistent methodologies and guides and the results of the additional evaluation process using a new set of evaluation criteria developed for the evaluation of the new methodologies.

A Real-Time Safety and Quality Reporting System: Assessment of Clinical Data and Staff Participation

International Nuclear Information System (INIS)

Rahn, Douglas A.; Kim, Gwe-Ya; Mundt, Arno J.; Pawlicki, Todd

2014-01-01

Purpose: To report on the use of an incident learning system in a radiation oncology clinic, along with a review of staff participation. Methods and Materials: On September 24, 2010, our department initiated an online real-time voluntary reporting system for safety issues, called the Radiation Oncology Quality Reporting System (ROQRS). We reviewed these reports from the program's inception through January 18, 2013 (2 years, 3 months, 25 days) to assess error reports (defined as both near-misses and incidents of inaccurate treatment). Results: During the study interval, there were 60,168 fractions of external beam radiation therapy and 955 brachytherapy procedures. There were 298 entries in the ROQRS system, among which 108 errors were reported. There were 31 patients with near-misses reported and 27 patients with incidents of inaccurate treatment reported. These incidents of inaccurate treatment occurred in 68 total treatment fractions (0.11% of treatments delivered during the study interval). None of these incidents of inaccurate treatment resulted in deviation from the prescription by 5% or more. A solution to the errors was documented in ROQRS in 65% of the cases. Errors occurred as repeated errors in 22% of the cases. A disproportionate number of the incidents of inaccurate treatment were due to improper patient setup at the linear accelerator (P<.001). Physician participation in ROQRS was nonexistent initially, but improved after an education program. Conclusions: Incident learning systems are a useful and practical means of improving safety and quality in patient care

A Real-Time Safety and Quality Reporting System: Assessment of Clinical Data and Staff Participation

Energy Technology Data Exchange (ETDEWEB)

Rahn, Douglas A.; Kim, Gwe-Ya; Mundt, Arno J.; Pawlicki, Todd, E-mail: tpawlicki@ucsd.edu

2014-12-01

Purpose: To report on the use of an incident learning system in a radiation oncology clinic, along with a review of staff participation. Methods and Materials: On September 24, 2010, our department initiated an online real-time voluntary reporting system for safety issues, called the Radiation Oncology Quality Reporting System (ROQRS). We reviewed these reports from the program's inception through January 18, 2013 (2 years, 3 months, 25 days) to assess error reports (defined as both near-misses and incidents of inaccurate treatment). Results: During the study interval, there were 60,168 fractions of external beam radiation therapy and 955 brachytherapy procedures. There were 298 entries in the ROQRS system, among which 108 errors were reported. There were 31 patients with near-misses reported and 27 patients with incidents of inaccurate treatment reported. These incidents of inaccurate treatment occurred in 68 total treatment fractions (0.11% of treatments delivered during the study interval). None of these incidents of inaccurate treatment resulted in deviation from the prescription by 5% or more. A solution to the errors was documented in ROQRS in 65% of the cases. Errors occurred as repeated errors in 22% of the cases. A disproportionate number of the incidents of inaccurate treatment were due to improper patient setup at the linear accelerator (P<.001). Physician participation in ROQRS was nonexistent initially, but improved after an education program. Conclusions: Incident learning systems are a useful and practical means of improving safety and quality in patient care.

Knowledge Representation in Patient Safety Reporting: An Ontological Approach

OpenAIRE

Liang Chen; Yang Gong

2016-01-01

Purpose: The current development of patient safety reporting systems is criticized for loss of information and low data quality due to the lack of a uniformed domain knowledge base and text processing functionality. To improve patient safety reporting, the present paper suggests an ontological representation of patient safety knowledge. Design/methodology/approach: We propose a framework for constructing an ontological knowledge base of patient safety. The present paper describes our desig...

Ignalina Safety Analysis Group's report for the year 1998

International Nuclear Information System (INIS)

Uspuras, E.; Augutis, J.; Bubelis, E.; Cesna, B.; Kaliatka, A.

1999-02-01

Results of Ignalina NPP Safety Analysis Group's research are presented. The main fields of group's activities in 1998 were following: safety analysis of reactor's cooling system, safety analysis of accident localization system, investigation of the problem graphite - fuel channel, reactor core modelling, assistance to the regulatory body VATESI in drafting regulations and reviewing safety reports presented by Ignalina NPP during the process of licensing of unit 1

Fusion safety program Annual report, Fiscal year 1995

International Nuclear Information System (INIS)

Longhurst, G.R.; Cadwallader, L.C.; Carmack, W.J.

1995-12-01

This report summarizes the major activities of the Fusion Safety Program in FY-95. The Idaho National Engineering Laboratory (INEL) is the designated lead laboratory, and Lockheed Idaho Technologies Company is the prime contractor for this program. The Fusion Safety Program was initiated in 1979. Activities are conducted at the INEL, at other DOE laboratories, and at other institutions. Among the technical areas covered in this report are tritium safety, beryllium safety, chemical reactions and activation product release, safety aspects of fusion magnet systems, plasma disruptions, risk assessment failure rate database development, and safety code development and application to fusion safety issues. Most of this work has been done in support of the International Thermonuclear Experimental Reactor (ITER). Also included in the report are summaries of the safety and environmental studies performed by the Fusion Safety Program for the Tokamak Physics Experiment and the Tokamak Fusion Test Reactor and the technical support for commercial fusion facility conceptual design studies. A final activity described is work to develop DOE Technical Standards for Safety of Fusion Test Facilities

78 FR 14877 - Pipeline Safety: Incident and Accident Reports

Science.gov (United States)

2013-03-07

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration [Docket ID PHMSA-2013-0028] Pipeline Safety: Incident and Accident Reports AGENCY: Pipeline and Hazardous Materials... PHMSA F 7100.2--Incident Report--Natural and Other Gas Transmission and Gathering Pipeline Systems and...

Nuclear Reactor RA Safety Report, Format and Contents

International Nuclear Information System (INIS)

1986-11-01

This is a new complete version of the safety report of nuclear reactor RA is made according to the recommendations of the IAEA. Report includes all the relevant data needed for evaluation of safe operation of this nuclear facility. Each of seven volumes of this report cover separate topics as follows: (1) introduction; (2) Site characteristics; (3) description of the reactor building and installations; (4) description of the reactor; (5) description of the coolant system; (6) description of the regulation and safety instrumentation; (7) description of the power supply system; (8) description of the auxiliary systems; (9) radiation protection issues; (10) radioactive waste management (11) reactor operation; (12) accident analysis during previous operation; (13) analysis of possible accident causes; (14) safety analysis and preventive actions: (15) analysis of significant accidents; (16) analysis of maximum possible accident; (17) environmental impact analysis in case of accident [sr

Patient Safety Learning Systems: A Systematic Review and Qualitative Synthesis.

Science.gov (United States)

2017-01-01

A patient safety learning system (sometimes called a critical incident reporting system) refers to structured reporting, collation, and analysis of critical incidents. To inform a provincial working group's recommendations for an Ontario Patient Safety Event Learning System, a systematic review was undertaken to determine design features that would optimize its adoption into the health care system and would inform implementation strategies. The objective of this review was to address two research questions: (a) what are the barriers to and facilitators of successful adoption of a patient safety learning system reported by health professionals and (b) what design components maximize successful adoption and implementation? To answer the first question, we used a published systematic review. To answer the second question, we used scoping study methodology. Common barriers reported in the literature by health care professionals included fear of blame, legal penalties, the perception that incident reporting does not improve patient safety, lack of organizational support, inadequate feedback, lack of knowledge about incident reporting systems, and lack of understanding about what constitutes an error. Common facilitators included a non-accusatory environment, the perception that incident reporting improves safety, clarification of the route of reporting and of how the system uses reports, enhanced feedback, role models (such as managers) using and promoting reporting, legislated protection of those who report, ability to report anonymously, education and training opportunities, and clear guidelines on what to report. Components of a patient safety learning system that increased successful adoption and implementation were emphasis on a blame-free culture that encourages reporting and learning, clear guidelines on how and what to report, making sure the system is user-friendly, organizational development support for data analysis to generate meaningful learning outcomes

Radiological, health, and safety, and occurrence reporting system audit report, Rifle, Colorado

International Nuclear Information System (INIS)

1993-11-01

This paper describes an audit dated September 14--16, 1993. The performance of the contractors and subcontractors responsible for remedial action work at the former uranium ore processing site at Rifle, Colorado, and the uranium tailings disposal cell at Estes Gulch (Colorado) was reviewed during an audit conducted September 14 through 16, 1993. MK-Ferguson Company (MK-F) is the Remedial Action Contractor (RAC) responsible for engineering and construction management of the Rifle operations. The audit focused on radiological issues, occupational safety and health (OS ampersand H) issues, and the Occurrence Reporting and Processing System (ORPS). The close-out meeting was held on September 16, 1993, which was attended by representatives of MK-F, the US Department of Energy (DOE), and the Technical Assistance Contractor (TAC)

System and safety studies of accelerator driven transmutation Annual Report 2005

Energy Technology Data Exchange (ETDEWEB)

Gudowski, Waclaw; Wallenius, Jan; Arzhanov, Vasily; Jolkkonen, Mikael; Eriksson, Marcus; Seltborg, Per; Westlen, Daniel; Lagerstedt, Christina; Isaksson, Patrick; Persson, Carl-Magnus; Aalander, Alexandra [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2006-11-15

The results of the research activities on System and Safety of Accelerator-Driven Transmutation (ADS) at the Department of Nuclear and Reactor Physics are described in this report followed by the Appendices of the relevant scientific papers published in 2005. PhD and Licentiate dissertations of Marcus Ericsson, Per Seltborg, Christina Lagerstedt and Daniel Westlen (see Appendices) reflect the research mainstream of 2005. Year 2005 was also very rich in international activities with ADS in focus. Summary of conferences, seminars and lecturing activities is given in Chapter 9 Research activities of 2005 have been focused on several areas: system and safety studies of ADS; subcritical experiments; ADS source efficiency studies; nuclear fuel cycle analysis; potential of reactor based transmutation; ADS fuel development; simulation of radiation damage; and development of codes and methods. Large part of the research activities has been well integrated with the European projects of the 5th and 6th Framework Programmes of the European Commission in which KTH is actively participating. In particular European projects: RED-IMPACT, CONFIRM, FUTURE, EUROTRANS and NURESIM.

System and safety studies of accelerator driven transmutation. Annual Report 2005

International Nuclear Information System (INIS)

Gudowski, Waclaw; Wallenius, Jan; Arzhanov, Vasily; Jolkkonen, Mikael; Eriksson, Marcus; Seltborg, Per; Westlen, Daniel; Lagerstedt, Christina; Isaksson, Patrick; Persson, Carl-Magnus; Aalander, Alexandra

2006-11-01

The results of the research activities on System and Safety of Accelerator-Driven Transmutation (ADS) at the Department of Nuclear and Reactor Physics are described in this report followed by the Appendices of the relevant scientific papers published in 2005. PhD and Licentiate dissertations of Marcus Ericsson, Per Seltborg, Christina Lagerstedt and Daniel Westlen (see Appendices) reflect the research mainstream of 2005. Year 2005 was also very rich in international activities with ADS in focus. Summary of conferences, seminars and lecturing activities is given in Chapter 9 Research activities of 2005 have been focused on several areas: system and safety studies of ADS; subcritical experiments; ADS source efficiency studies; nuclear fuel cycle analysis; potential of reactor based transmutation; ADS fuel development; simulation of radiation damage; and development of codes and methods. Large part of the research activities has been well integrated with the European projects of the 5th and 6th Framework Programmes of the European Commission in which KTH is actively participating. In particular European projects: RED-IMPACT, CONFIRM, FUTURE, EUROTRANS and NURESIM

75 FR 51521 - Federal Motor Vehicle Safety Standards; Air Brake Systems; Technical Report on the Effectiveness...

Science.gov (United States)

2010-08-20

....121) mandates antilock braking systems (ABS) on all new air-braked vehicles with a GVWR of 10,000...-0116] Federal Motor Vehicle Safety Standards; Air Brake Systems; Technical Report on the Effectiveness of Antilock Braking Systems in Heavy Truck Tractors and Trailers AGENCY: National Highway Traffic...

Nitrogen-system safety study: Portsmouth Gaseous Diffusion Plant

International Nuclear Information System (INIS)

1982-07-01

The Department of Energy has primary responsibility for the safety of operations at DOE-owned nuclear facilities. The guidelines for the analysis of credible accidents are outlined in DOE Order 5481.1. DOE has requested that existing plant facilities and operations be reviewed for potential safety problems not covered by standard industrial safety procedures. This review is being conducted by investigating individual facilities and documenting the results in Safety Study Reports which will be compiled to form the Existing Plant Final Safety Analysis Report which is scheduled for completion in September, 1984. This Safety Study documents the review of the Plant Nitrogen System facilities and operations and consists of Section 4.0, Facility and Process Description, and Section 5.0, Accident Analysis, of the Final Safety Analysis Report format. The existing nitrogen system consists of a Superior Air Products Company Type D Nitrogen Plant, nitrogen storage facilities, vaporization facilities and a distribution system. The system is designed to generate and distribute nitrogen gas used in the cascade for seal feed, buffer systems, and for servicing equipment when exceptionally low dew points are required. Gaseous nitrogen is also distributed to various process auxiliary buildings. The average usage is approximately 130,000 standard cubic feet per day

Knowledge Representation in Patient Safety Reporting: An Ontological Approach

Directory of Open Access Journals (Sweden)

Liang Chen

2016-10-01

Full Text Available Purpose: The current development of patient safety reporting systems is criticized for loss of information and low data quality due to the lack of a uniformed domain knowledge base and text processing functionality. To improve patient safety reporting, the present paper suggests an ontological representation of patient safety knowledge. Design/methodology/approach: We propose a framework for constructing an ontological knowledge base of patient safety. The present paper describes our design, implementation, and evaluation of the ontology at its initial stage. Findings: We describe the design and initial outcomes of the ontology implementation. The evaluation results demonstrate the clinical validity of the ontology by a self-developed survey measurement. Research limitations: The proposed ontology was developed and evaluated using a small number of information sources. Presently, US data are used, but they are not essential for the ultimate structure of the ontology. Practical implications: The goal of improving patient safety can be aided through investigating patient safety reports and providing actionable knowledge to clinical practitioners. As such, constructing a domain specific ontology for patient safety reports serves as a cornerstone in information collection and text mining methods. Originality/value: The use of ontologies provides abstracted representation of semantic information and enables a wealth of applications in a reporting system. Therefore, constructing such a knowledge base is recognized as a high priority in health care.

Safety analysis report for packaging onsite long-length contaminated equipment transport system

International Nuclear Information System (INIS)

McCormick, W.A.

1997-01-01

This safety analysis report for packaging describes the components of the long-length contaminated equipment (LLCE) transport system (TS) and provides the analyses, evaluations, and associated operational controls necessary for the safe use of the LLCE TS on the Hanford Site. The LLCE TS will provide a standardized, comprehensive approach for the disposal of approximately 98% of LLCE scheduled to be removed from the 200 Area waste tanks

Safety analysis report for packaging, onsite, long-length contaminated equipment transport system

Energy Technology Data Exchange (ETDEWEB)

McCormick, W.A.

1997-05-09

This safety analysis report for packaging describes the components of the long-length contaminated equipment (LLCE) transport system (TS) and provides the analyses, evaluations, and associated operational controls necessary for the safe use of the LLCE TS on the Hanford Site. The LLCE TS will provide a standardized, comprehensive approach for the disposal of approximately 98% of LLCE scheduled to be removed from the 200 Area waste tanks.

System and safety studies of accelerator driven transmutation. Annual Report 2001

International Nuclear Information System (INIS)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J.; Chakarova, R.; Westlen, D.

2002-03-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics has been focused in year 2001 on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics; c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache) and YALINA experiment in Minsk. The Dept. is very actively participating in many European projects in the 5th Framework Programme of the European Community. Most of the research topics reported in this paper are referred to by appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details

System and safety studies of accelerator driven transmutation. Annual Report 2001

Energy Technology Data Exchange (ETDEWEB)

Gudowski, W; Wallenius, J; Tucek, K; Eriksson, Marcus; Carlsson, Johan; Seltborg, P; Cetnar, J; Chakarova, R; Westlen, D [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2002-03-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the Dept. of Nuclear and Reactor Physics has been focused in year 2001 on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics; c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache) and YALINA experiment in Minsk. The Dept. is very actively participating in many European projects in the 5th Framework Programme of the European Community. Most of the research topics reported in this paper are referred to by appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details.

Safety implications of electronic driving support systems : an orientation.

NARCIS (Netherlands)

Gundy, C.M. Steyvers, F.J.J.M. & Kaptein, N.A.

1995-01-01

This report focuses on traffic safety aspects of driving support systems. The report consists of two parts. First of all, the report discusses a number of topics, relevant for the implementation and evaluation of driving support systems. These topics include: (1) safety research into driving support

System and safety studies of accelerator driven systems for transmutation. Annual report 2007

International Nuclear Information System (INIS)

Arzhanov, Vasily; Fokau, Andrei; Persson, Calle; Runevall, Odd; Sandberg, Nils; Tesinsky, Milan; Wallenius, Janne; Youpeng Zhang

2008-05-01

Within the project 'System and safety studies of accelerator driven systems for transmutation', research on design and safety of sub-critical reactors for recycling of minor actinides is performed. During 2007, the reactor physics division at KTH has calculated safety parameters for EFIT-400 with cermet fuel, permitting to start the transient safety analysis. The accuracy of different reactivity meters applied to the YALINA facility was assessed and neutron detection studies were performed. A model to address deviations from point kinetic behaviour was developed. Studies of basic radiation damage physics included calculations of vacancy formation and activation enthalpies in bcc niobium. In order to predict the oxygen potential of inert matrix fuels, a thermo-chemical model for mixed actinide oxides was implemented in a phase equilibrium code

A status report regarding industry implementation of safety parameter display systems

International Nuclear Information System (INIS)

Lapinsky, G.W. Jr.; Eckenrode, R.J.; Goodman, P.C.; Correia, R.P.

1989-04-01

This report provides a summary of the results of the US Nuclear Regulatory Commission staff's review of installed safety parameter display systems (SPDS) at 57 nuclear units. The staff describes its rationale and practice for determining acceptability of some of the methods for satisfying the various requirements for SPDS as well as some methods that the staff has not accepted. The staff's discussion of identified strengths and weaknesses should aid licensees in solving some of the problems they may be experiencing with their SPDS

Plutonium Finishing Plant safety evaluation report

International Nuclear Information System (INIS)

1995-01-01

The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) is DOE's independent review and evaluation of the PFP FSAR and the basis for approval of the PFP FSAR. The evaluation is presented in a format that parallels the format of the PFP FSAR. As an aid to the reactor, a list of acronyms has been included at the beginning of this report. The DOE review concluded that the risks associated with conducting plutonium handling, processing, and storage operations within PFP facilities, as described in the PFP FSAR, are acceptable, since the accident safety analyses associated with these activities meet the WHC risk acceptance guidelines and DOE safety goals in SEN-35-91

Technical self reliance of digital safety systems

Energy Technology Data Exchange (ETDEWEB)

Kwon, Kee Choon; Lee, Dong Young [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Kook Hun [Doosan Heavy Industries and Construction, Changwon (Korea, Republic of); Choi, Seung Gap [POSCON, Pohang (Korea, Republic of)

2009-04-15

This paper summarizes the development results of the Korea Nuclear Instrumentation and Control System (KNICS) project sponsored by the Korean government. In this project, Man Machine Interface System (MMIS) architecture, two digital platforms, and several control systems are developed. One platform is a programmable Logic Controller (PLC) for a safety system and another platform is a Distributed Control System (DCS) for a non safety system. With the POSAFE Q PLC, a Reactor Protection System (RPS) and an Engineered Safety Feature Component Control System (ESF CCS) are developed. A Power Control System (PCS) is developed based on the DCS. The safety grade platform and the digital safety systems obtained approval for the Topical Report from the Korean regulatory body in February of 2009. Also a Korean utility and a vendor company determined KNICS results to apply them to the planned Nuclear Power Plant (NPP) in March 2009. This paper introduces the technical self reliance experiences of the safety grade platform and the digital safety systems developed in the KNICS R and D project.

Safety implications of electronic driving support systems : an orientation.

OpenAIRE

Gundy, C.M. Steyvers, F.J.J.M. & Kaptein, N.A.

1995-01-01

This report focuses on traffic safety aspects of driving support systems. The report consists of two parts. First of all, the report discusses a number of topics, relevant for the implementation and evaluation of driving support systems. These topics include: (1) safety research into driving support systems: (2) the importance of research into driver models and the driving task; (3) horizontal integration of driving support systems; (4) vertical integration of driving support systems; (5) tas...

Review of safety reports involving electronic flight bags

Science.gov (United States)

2009-04-27

Electronic Flight Bags (EFBs) are a relatively new device used by pilots. Even so, 37 safety-related events involving EFBs were identified from the public online Aviation Safety Reporting System (ASRS) database as of June 2008. In addition, two accid...

System and safety studies of accelerator driven systems for transmutation. Annual report 2007

Energy Technology Data Exchange (ETDEWEB)

Arzhanov, Vasily; Fokau, Andrei; Persson, Calle; Runevall, Odd; Sandberg, Nils; Tesinsky, Milan; Wallenius, Janne; Youpeng Zhang (Div. of Reactor Physics, Royal Institute of Technology, Stockholm (Sweden))

2008-05-15

Within the project 'System and safety studies of accelerator driven systems for transmutation', research on design and safety of sub-critical reactors for recycling of minor actinides is performed. During 2007, the reactor physics division at KTH has calculated safety parameters for EFIT-400 with cermet fuel, permitting to start the transient safety analysis. The accuracy of different reactivity meters applied to the YALINA facility was assessed and neutron detection studies were performed. A model to address deviations from point kinetic behaviour was developed. Studies of basic radiation damage physics included calculations of vacancy formation and activation enthalpies in bcc niobium. In order to predict the oxygen potential of inert matrix fuels, a thermo-chemical model for mixed actinide oxides was implemented in a phase equilibrium code

Fusion Safety Program annual report, fiscal year 1994

International Nuclear Information System (INIS)

Longhurst, G.R.; Cadwallader, L.C.; Dolan, T.J.; Herring, J.S.; McCarthy, K.A.; Merrill, B.J.; Motloch, C.G.; Petti, D.A.

1995-03-01

This report summarizes the major activities of the Fusion Safety Program in fiscal year 1994. The Idaho National Engineering Laboratory (INEL) is the designated lead laboratory and Lockheed Idaho Technologies Company is the prime contractor for this program. The Fusion Safety Program was initiated in 1979. Activities are conducted at the INEL, at other DOE laboratories, and at other institutions, including the University of Wisconsin. The technical areas covered in this report include tritium safety, beryllium safety, chemical reactions and activation product release, safety aspects of fusion magnet systems, plasma disruptions, risk assessment failure rate data base development, and thermalhydraulics code development and their application to fusion safety issues. Much of this work has been done in support of the International Thermonuclear Experimental Reactor (ITER). Also included in the report are summaries of the safety and environmental studies performed by the Fusion Safety Program for the Tokamak Physics Experiment and the Tokamak Fusion Test Reactor and of the technical support for commercial fusion facility conceptual design studies. A major activity this year has been work to develop a DOE Technical Standard for the safety of fusion test facilities

Critical evaluation of nuclear safety reports Pt. 1

International Nuclear Information System (INIS)

Egely, Gy.

1987-01-01

Licensing procedures of siting, commissioning and operation of nuclear power plants in the USA, FRG, France and Japan are compared. The standard format and content of nuclear safety analysis reports including the general description of the plant, the presentation of the characteristics of siting, building structures, components, facilities, the reactors, the cooling system, the safety system, the measuring and control system, the power supply system, the auxilliary system, the energy transformation system, etc. are discussed in detail by the example of the US procedure. (V.N.)

Fusion Safety Program annual report, Fiscal Year 1993

International Nuclear Information System (INIS)

Longhurst, G.R.; Cadwallader, L.C.; Dolan, T.J.; Herring, J.S.; McCarthy, K.A.; Merrill, B.J.; Motloch, C.G.; Petti, D.A.

1993-12-01

This report summarizes the major activities of the Fusion Safety Program in Fiscal Year 1993. The Idaho National Engineering Laboratory (INEL) has been designated by DOE as the lead laboratory for fusion safety, and EG ampersand G Idaho, Inc., is the prime contractor for INEL operations. The Fusion Safety Program was initiated in 1979. Activities are conducted at the INEL and in participating organizations, including universities and private companies. Technical areas covered in the report include tritium safety, beryllium safety, activation product release, reactions involving potential plasma-facing materials, safety of fusion magnet systems, plasma disruptions and edge physics modeling, risk assessment failure rates, computer codes for reactor transient analysis, and regulatory support. These areas include work completed in support of the International Thermonuclear Experimental Reactor (ITER). Also included in the report are summaries of the safety and environmental studies performed at the INEL for the Tokamak Physics Experiment and the Tokamak Fusion Test Reactor projects at the Princeton Plasma Physics Laboratory and a summary of the technical support for the ARIES/PULSAR commercial reactor design studies

Safety analysis reports. Current status (third key report)

International Nuclear Information System (INIS)

1999-01-01

A review of Ukrainian regulations and laws concerned with Nuclear power and radiation safety is presented with an overview of the requirements for the Safety Analysis Report Contents. Status of Safety Analysis Reports (SAR) is listed for each particular Ukrainian NPP including SAR development schedules. Organisational scheme of SAR development works includes: general technical co-ordination on Safety Analysis Report development; list of leading organisations and utilization of technical support within international projects

Safety Test Report for the PWR S/F Dry Storage System

Energy Technology Data Exchange (ETDEWEB)

Seo, K. S.; Lee, J. H.; Koo, K. H.; Lee, J. C.; Choi, W. S.; Bang, K. S.; Park, H. Y.; Jang, S. Y

2008-10-15

This is contract report conducted by KAERI under the contract with NETEC for safety test for the PWR S/F dry storage system. Leak Test was performed after drop test and turn-over test, the measured leakage rate was lower than allowable leakage rate. It is revealed that the containment integrity of the dry storage system is maintained. In the seismic test, the moving of the model was measured at SRTH seismic response of 0.4 g and 0.8 g. Therefore the seismic test results can be used fully to the test data for verification of the seismic analysis. In the thermal test, the direction of the inlet and outlet of the air has no effect on the heat transfer performance. The passive heat removal system of the horizontal storage module was designed well.

Reports about Occurrence of Events with Effect on Aviation Safety

Directory of Open Access Journals (Sweden)

Vladimír Plos

2014-07-01

Full Text Available This article deals with a system, that is established to report the events with effect on safety. This system is based on requirements published in Annex 13 to the Chicago Convention and legislative foundations laid down in Regulation L13, Regulation of the European Parliament and of the Council (EU No 376/2014, Decree No. 359/2006 Sb. and Act No. 49/1997 Sb. Standards and legislative rules precisely define the types of events that are subject of reporting and also define the structure and content of the reporting message. This content is consists mainly of the identification data about the airplane and crew, information about the route and a short description of the damage to the airplane. In the following, we discuss the possible use of such a system of mandatory reporting for the needs of safety indicators. Then there are proposals of changes in the content of the reporting message for the need of safety indicators. The present knowledge indicates that the use of all opportunities provided by the law for the reporting of events can lead to a creating of sufficient basis for safety indicators.

Software reliability and safety in nuclear reactor protection systems

Energy Technology Data Exchange (ETDEWEB)

Lawrence, J.D. [Lawrence Livermore National Lab., CA (United States)

1993-11-01

Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor.

Software reliability and safety in nuclear reactor protection systems

International Nuclear Information System (INIS)

Lawrence, J.D.

1993-11-01

Planning the development, use and regulation of computer systems in nuclear reactor protection systems in such a way as to enhance reliability and safety is a complex issue. This report is one of a series of reports from the Computer Safety and Reliability Group, Lawrence Livermore that investigates different aspects of computer software in reactor National Laboratory, that investigates different aspects of computer software in reactor protection systems. There are two central themes in the report, First, software considerations cannot be fully understood in isolation from computer hardware and application considerations. Second, the process of engineering reliability and safety into a computer system requires activities to be carried out throughout the software life cycle. The report discusses the many activities that can be carried out during the software life cycle to improve the safety and reliability of the resulting product. The viewpoint is primarily that of the assessor, or auditor

Feedback from incident reporting: information and action to improve patient safety.

Science.gov (United States)

Benn, J; Koutantji, M; Wallace, L; Spurgeon, P; Rejman, M; Healey, A; Vincent, C

2009-02-01

Effective feedback from incident reporting systems in healthcare is essential if organisations are to learn from failures in the delivery of care. Despite the wide-scale development and implementation of incident reporting in healthcare, studies in the UK suggest that information concerning system vulnerabilities could be better applied to improve operational safety within organisations. In this article, the findings and implications of research to identify forms of effective feedback from incident reporting are discussed, to promote best practices in this area. The research comprised a mixed methods review to investigate mechanisms of effective feedback for healthcare, drawing upon experience within established reporting programmes in high-risk industry and transport domains. Systematic searches of published literature were undertaken, and 23 case studies describing incident reporting programmes with feedback were identified for analysis from the international healthcare literature. Semistructured interviews were undertaken with 19 subject matter experts across a range of domains, including: civil aviation, maritime, energy, rail, offshore production and healthcare. In analysis, qualitative information from several sources was synthesised into practical requirements for developing effective feedback in healthcare. Both action and information feedback mechanisms were identified, serving safety awareness, improvement and motivational functions. The provision of actionable feedback that visibly improved systems was highlighted as important in promoting future reporting. Fifteen requirements for the design of effective feedback systems were identified, concerning: the role of leadership, the credibility and content of information, effective dissemination channels, the capacity for rapid action and the need for feedback at all levels of the organisation, among others. Above all, the safety-feedback cycle must be closed by ensuring that reporting, analysis and

Aviation Safety Hotline Information System -

Data.gov (United States)

Department of Transportation — The Aviation Safety Hotline Information System (ASHIS) collects, stores, and retrieves reports submitted by pilots, mechanics, cabin crew, passengers, or the public...

Safety status system for operating room devices.

Science.gov (United States)

Guédon, Annetje C P; Wauben, Linda S G L; Overvelde, Marlies; Blok, Joleen H; van der Elst, Maarten; Dankelman, Jenny; van den Dobbelsteen, John J

2014-01-01

Since the increase of the number of technological aids in the operating room (OR), equipment-related incidents have come to be a common kind of adverse events. This underlines the importance of adequate equipment management to improve the safety in the OR. A system was developed to monitor the safety status (periodic maintenance and registered malfunctions) of OR devices and to facilitate the notification of malfunctions. The objective was to assess whether the system is suitable for use in an busy OR setting and to analyse its effect on the notification of malfunctions. The system checks automatically the safety status of OR devices through constant communication with the technical facility management system, informs the OR staff real-time and facilitates notification of malfunctions. The system was tested for a pilot period of six months in four ORs of a Dutch teaching hospital and 17 users were interviewed on the usability of the system. The users provided positive feedback on the usability. For 86.6% of total time, the localisation of OR devices was accurate. 62 malfunctions of OR devices were reported, an increase of 12 notifications compared to the previous year. The safety status system was suitable for an OR complex, both from a usability and technical point of view, and an increase of reported malfunctions was observed. The system eases monitoring the safety status of equipment and is a promising tool to improve the safety related to OR devices.

National Nuclear Safety Report 2001. Convention on Nuclear Safety

International Nuclear Information System (INIS)

2001-01-01

The First National Nuclear Safety Report was presented at the first review meeting of the Nuclear Safety Convention. At that time it was concluded that Argentina met the obligations of the Convention. This second National Nuclear Safety Report is an updated report which includes all safety aspects of the Argentinian nuclear power plants and the measures taken to enhance the safety of the plants. The present report also takes into account the observations and discussions maintained during the first review meeting. The conclusion made in the first review meeting about the compliance by Argentina of the obligations of the Convention are included as Annex 1. In general, the information contained in this Report has been updated since March 31, 1998 to March 31, 2001. Those aspects that remain unchanged were not addressed in this second report with the objective of avoiding repetitions and in order to carry out a detailed analysis considering article by article. As a result of the above mentioned detailed analysis of all the Articles, it can be stated that the country fulfils all the obligations imposed by the Nuclear Safety Convention

National nuclear safety report 2004. Convention on nuclear safety

International Nuclear Information System (INIS)

2004-01-01

The second National Nuclear Safety Report was presented at the second review meeting of the Nuclear Safety Convention. At that time it was concluded that Argentina met the obligations of the Convention. This third National Nuclear Safety Report is an updated report which includes all safety aspects of the Argentinian nuclear power plants and the measures taken to enhance the safety of the plants. The present report also takes into account the observations and discussions maintained during the second review meeting. The conclusion made in the first review meeting about the compliance by Argentina of the obligations of the Convention are included as Annex I and those belonging to the second review meeting are included as Annex II. In general, the information contained in this Report has been updated since March 31, 2001 to April 30, 2004. Those aspects that remain unchanged were not addressed in this third report. As a result of the detailed analysis of all the Articles, it can be stated that the country fulfils all the obligations imposed by the Nuclear Safety Convention. The questions and answers originated at the Second Review Meeting are included as Annex III

Interim process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Sellin, Patrick

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses

Interim process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Sellin, Patrick (ed.)

2004-08-01

This report is a documentation of buffer processes identified as relevant to the long-term safety of a KBS-3 repository. The report is part of the interim reporting of the safety assessment SR-Can, see further the Interim main report. The final SR-Can reporting will support SKB's application to build an Encapsulation plant for spent nuclear fuel and is to be produced in 2006. The purpose of this report is to document the scientific knowledge of the processes to a level required for an adequate treatment in the safety assessment. The documentation is thus from a scientific point of not exhaustive since such a treatment is neither necessary for the purposes of the safety assessment nor possible within the scope of an assessment. The purpose is further to determine the handling of each process in the safety assessment and to demonstrate how uncertainties are taken care of, given the suggested handling. The process documentation in the SR 97 version of the Process report is a starting point for this SR-Can interim version. As further described in the Interim main report, the list of relevant processes has been reviewed and slightly extended by comparison to other databases. Furthermore, the backfill has been included as a system part of its own, rather than being described together with the buffer as in SR 97. Apart from giving an interim account of the documentation and handling of buffer processes in SR-Can, this report is meant to serve as a template for the forthcoming documentation of processes occurring in other parts of the repository system. A complete list of processes can be found in the Interim FEP report for the safety assessment SR-Can. All material presented in this document is preliminary in nature and will possibly be updated as the SR-Can project progresses.

Annual Safety Report 1981

International Nuclear Information System (INIS)

1982-09-01

A safety report from Section K (Nuclear Physics) of the Dutch National Institute for Nuclear and High Energy Physics is presented for 1981. The report begins with general matters concerning safety policy at NIKHEF, licences and expenditure. Works accidents (none of them radiological) are detailed and accident prevention considered. The measurement programme for neutron radiation in the vicinity of the accelerator is described and the results are discussed. The means and results of personnel dosimetry are also presented. The report is concluded with a list of publications concerning safety aspects at NIKHEF. (C.F.)

Development and application of digital safety system in NPPs

International Nuclear Information System (INIS)

Kwon, Keechoon; Kim, Changhwoi; Lee, Dongyoung

2012-01-01

This paper describes the development of digital safety system in NPPs based on safety- grade programmable logic controller (PLC) platform and its application to real NPP construction. The digital safety system consists of a reactor protection system and an engineered safety feature-component control system. The safety-grade PLC platform was developed so that it meets the requirements of the regulation. The PLC consists of various modules such as a power module, a processor module, communication modules, digital input/output modules, analog input/output modules, a LOCA bus extension module, and a high-speed pulse counter module. The reactor protection system is designed with a redundant 4-channel architecture, and every channel is implemented with the same architecture. A single channel consists of a redundant bi-stable processor, a redundant coincidence processor, an automatic test and interface processor, and a cabinet operator module. The engineered safety feature-component control system is designed with four redundant divisions, and implemented with the PLC platform. The principal components of an individual division are fault tolerant group controllers, loop controllers, a test and interface processor, a cabinet operator module and a control channel gateway. The topical report is submitted to the regulatory body, and got safety evaluation report from the regulatory body. Also, the developed system is tested in the integrated performance validation facility. It is decided that the digital safety system applied to Shin-Uljin unit 1 and 2 after a topical report approval and validation test. Design changes occur in the digital safety system that is applied to an actual nuclear power plant construction, and the PLC has also been upgraded

Development and application of digital safety system in NPPs

Energy Technology Data Exchange (ETDEWEB)

Kwon, Keechoon; Kim, Changhwoi; Lee, Dongyoung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2012-03-15

This paper describes the development of digital safety system in NPPs based on safety- grade programmable logic controller (PLC) platform and its application to real NPP construction. The digital safety system consists of a reactor protection system and an engineered safety feature-component control system. The safety-grade PLC platform was developed so that it meets the requirements of the regulation. The PLC consists of various modules such as a power module, a processor module, communication modules, digital input/output modules, analog input/output modules, a LOCA bus extension module, and a high-speed pulse counter module. The reactor protection system is designed with a redundant 4-channel architecture, and every channel is implemented with the same architecture. A single channel consists of a redundant bi-stable processor, a redundant coincidence processor, an automatic test and interface processor, and a cabinet operator module. The engineered safety feature-component control system is designed with four redundant divisions, and implemented with the PLC platform. The principal components of an individual division are fault tolerant group controllers, loop controllers, a test and interface processor, a cabinet operator module and a control channel gateway. The topical report is submitted to the regulatory body, and got safety evaluation report from the regulatory body. Also, the developed system is tested in the integrated performance validation facility. It is decided that the digital safety system applied to Shin-Uljin unit 1 and 2 after a topical report approval and validation test. Design changes occur in the digital safety system that is applied to an actual nuclear power plant construction, and the PLC has also been upgraded.

Research on advanced system safety assessment procedures (4)

International Nuclear Information System (INIS)

Suzuki, Kazuhiko; Shimada, Yukiyasu

2001-03-01

The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. This report surveys the literature on risk assessment and safety design based on the concept of independent protection layers (IPLs). Furthermore, to improve HAZOP System, tool is proposed to construct the basic model and the internal state model. Such HAZOP system is applied to analyze two kinds of processes, where the ability of the proposed system is verified. In addition, risk assessment support system is proposed to integrate safety design environment and assessment result to be used by other plants as well as to enable the underline plant to use other plants' information. This technique can be implemented using web-based safety information systems. (author)

Fusion Safety Program annual report: Fiscal year 1986

International Nuclear Information System (INIS)

Holland, D.F.; Merrill, B.J.; Herring, J.S.; Piet, S.J.; Longhurst, G.R.

1987-06-01

This report summarizes the Fusion Safety Program's (FSP) major activities in fiscal year 1986. The Idaho National Engineering Laboratory (INEL) is the designated lead laboratory, and EG and G Idaho, Inc., is the prime contractor for FSP, which was initiated in 1979. Activities are conducted at the INEL and in participating facilities, including the Hanford Engineering Development Laboratory (HEDL), the Massachusetts Institute of Technology (MIT), and the University of Wisconsin. The technical areas covered in this report include tritium safety, activation product release, reactions involving lithium breeding materials, safety of fusion magnet systems, plasma disruption, risk assessment methodology, and computer code development for reactor transients. Contributions to the Technical Planning Activity (TPA) and the ''white paper'' study by the Environmental, Safety,and Economics Committee (ESECOM) are summarized. The report also includes a summary of the safety and environmental analysis and documentation performed by the INEL for the Compact Ignition Tokamak (CIT) design project

Pre-Departure Clearance (PDC): An Analysis of Aviation Safety Reporting System Reports Concerning PDC Related Errors

Science.gov (United States)

Montalyo, Michael L.; Lebacqz, J. Victor (Technical Monitor)

1994-01-01

Airlines operating in the United States are required to operate under instrument flight rules (EFR). Typically, a clearance is issued via voice transmission from clearance delivery at the departing airport. In 1990, the Federal Aviation Administration (FAA) began deployment of the Pre-Departure Clearance (PDC) system at 30 U.S. airports. The PDC system utilizes aeronautical datalink and Aircraft Communication and Reporting System (ACARS) to transmit departure clearances directly to the pilot. An objective of the PDC system is to provide an immediate reduction in voice congestion over the clearance delivery frequency. Participating airports report that this objective has been met. However, preliminary analysis of 42 Aviation Safety Reporting System (ASRS) reports has revealed problems in PDC procedures and formatting which have caused errors in the proper execution of the clearance. It must be acknowledged that this technology, along with other advancements on the flightdeck, is adding more responsibility to the crew and increasing the opportunity for error. The present study uses these findings as a basis for further coding and analysis of an additional 82 reports obtained from an ASRS database search. These reports indicate that clearances are often amended or exceptions are added in order to accommodate local ATC facilities. However, the onboard ACARS is limited in its ability to emphasize or highlight these changes which has resulted in altitude and heading deviations along with increases in ATC workload. Furthermore, few participating airports require any type of PDC receipt confirmation. In fact, 35% of all ASRS reports dealing with PDC's include failure to acquire the PDC at all. Consequently, this study examines pilots' suggestions contained in ASRS reports in order to develop recommendations to airlines and ATC facilities to help reduce the amount of incidents that occur.

Data report for the safety assessment SR-Site

International Nuclear Information System (INIS)

2010-12-01

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Data report for the safety assessment SR-Site

Energy Technology Data Exchange (ETDEWEB)

2010-12-15

This report compiles, documents, and qualifies input data identified as essential for the long-term safety assessment of a KBS-3 repository, and forms an important part of the reporting of the safety assessment project SR-Site. The input data concern the repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock, and the biosphere in the proximity of the repository. The input data also concern external influences acting on the system, in terms of climate related data. Data are provided for a selection of relevant conditions and are qualified through traceable standardised procedures

Annual report 1988 of the Central Safety Department

International Nuclear Information System (INIS)

Koelzer, W.; Urban, M.

1989-04-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The r+d work concentrates on the following aspects: physical and chemical behavior of biologically particularly active radionuclides, behavior of tritium in the air/plant/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1988 routine tasks and reports about results of investigations and developments of the working groups of the Department. The reader is referred to the English translation of the Table of Contents and of Chapter 1 describing the duties and organization of the Central Safety Department. (orig./HP) [de

Annual report 1991 of the Central Safety Department

International Nuclear Information System (INIS)

Koelzer, W.

1992-04-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The research and development work concentrates on the following aspects: Physical and chemical behavior of trace elements in the environment, behavior of tritium in the air/plant/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1989 routine tasks and reports about results of investigations and developments of the working groups of the Department. The reader is referred to the English translation of the Table of Contents and of Chapter 1 describing the duties and organization of the Central Safety Department. (orig.) [de

Annual report 1990 of the Central Safety Department

International Nuclear Information System (INIS)

Koelzer, W.; Urban, M.

1991-04-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The research and development work concentrates on the following aspects: Physical and chemical behavior of trace elements in the environment, behavior of tritium in the air/plant/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1989 routine tasks and reports about results of investigations and developments of the working groups of the Department. The reader is referred to the English translation of the Table of Contents and of Chapter 1 describing the duties and organization of the Central Safety Department. (orig.) [de

Fusion Safety Program annual report, fiscal year 1992

International Nuclear Information System (INIS)

Holland, D.F.; Cadwallader, L.C.; Herring, J.S.; Longhurst, G.R.; McCarthy, K.A.; Merrill, B.J.; Piet, S.J.

1993-01-01

This report summarizes the major activities of the Fusion Safety Program in fiscal year 1992. The Idaho National Engineering Laboratory (INEL) is the designated lead laboratory and EG ampersand G Idaho, Inc. is the prime contractor for this program. The Fusion Safety Program was initiated in 1979. Activities are conducted at the INEL and in participating organizations including the Westinghouse Hanford Company at the Hanford Engineering Development Laboratory, the Massachusetts Institute of Technology, and the University of Wisconsin. The technical areas covered in the report include tritium safety, activation product release, reactions involving beryllium, reactions involving lithium breeding materials, safety of fusion magnet systems, plasma disruptions, risk assessment failure rate data base, and computer code development for reactor transients. Also included in the report is a summary of the safety and environmental studies performed by the INEL for the Tokamak Physics Experiments and the Tokamak Fusion Test Reactor, the safety analysis for the International Thermonuclear Experimental Reactor design, and the technical support for the ARIES commercial reactor design study

Fusion Safety Program annual report: Fiscal year 1987

International Nuclear Information System (INIS)

Holland, D.F.; Herring, J.S.; Longhurst, G.R.; Lyon, R.E.; Merrill, B.J.; Piet, S.J.

1988-02-01

This report summarizes the Fusion Safety Program major activities in fiscal year 1987. The Idaho National Engineering Laboratory (INEL) is the designated lead laboraotry and EG and G Idaho, Inc., is the prime contractor for this program, which was initiated in 1979. Activities are conducted at the INEL and in participating laboratories including the Hanford Engineering Development Laboratory (HEDL), the Massachusetts Institute of Technology (MIT), and the University of Wisconsin. The technical areas covered in the report include tritium safety, activation product release, reactions involving lithium breeding materials, safety of fusion magnet systems, plasma disruptions, risk assessment methodology, computer codes development for reactor transients, and fusion waste management. Also included in the report is a summary of the safety and environmental analysis and conventional facilities design performed by INEL for the Compact Ignition Tokamak design project, the safety analysis and documentation performed for the Tokamak Ignition/Burn Experimental Reactor design, and the technical support provided to the Environmental Safety and Economics Committee (ESECOM). 42 refs., 17 figs., 4 tabs

Safety balance: Analysis of safety systems

International Nuclear Information System (INIS)

Delage, M.; Giroux, C.

1990-12-01

Safety analysis, and particularly analysis of exploitation of NPPs is constantly affected by EDF and by the safety authorities and their methodologies. Periodic safety reports ensure that important issues are not missed on daily basis, that incidents are identified and that relevant actions are undertaken. French safety analysis method consists of three principal steps. First type of safety balance is analyzed at the normal start-up phase for each unit including the final safety report. This enables analysis of behaviour of units ten years after their licensing. Second type is periodic operational safety analysis performed during a few years. Finally, the third step consists of safety analysis of the oldest units with the aim to improve the safety standards. The three steps of safety analysis are described in this presentation in detail with the aim to present the objectives and principles. Examples of most recent exercises are included in order to illustrate the importance of such analyses

Overview of Risk Mitigation for Safety-Critical Computer-Based Systems

Science.gov (United States)

Torres-Pomales, Wilfredo

2015-01-01

This report presents a high-level overview of a general strategy to mitigate the risks from threats to safety-critical computer-based systems. In this context, a safety threat is a process or phenomenon that can cause operational safety hazards in the form of computational system failures. This report is intended to provide insight into the safety-risk mitigation problem and the characteristics of potential solutions. The limitations of the general risk mitigation strategy are discussed and some options to overcome these limitations are provided. This work is part of an ongoing effort to enable well-founded assurance of safety-related properties of complex safety-critical computer-based aircraft systems by developing an effective capability to model and reason about the safety implications of system requirements and design.

Safety analysis report for packaging (onsite) steel drum

International Nuclear Information System (INIS)

McCormick, W.A.

1998-01-01

This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum

Development and applications of a safety assessment system for promoting safety culture in nuclear power plants

International Nuclear Information System (INIS)

Takano, Ken-ichi; Hasegawa, Naoko; Hirose, Ayako; Hayase, Ken-ichi

2004-01-01

For past five years, CRIEPI has been continuing efforts to develop and make applications of a 'safety assessment system' which enable to measure the safety level of organization. This report describe about frame of the system, assessment results and its reliability, and relation between labor accident rate in the site and total safety index (TSI), which can be obtained by the principal factors analysis. The safety assessment in this report is based on questionnaire survey of employee. The format and concrete questionnaires were developed using existing literatures including organizational assessment tools. The tailored questionnaire format involved 124 questionnaire items. The assessment results could be considered as a well indicator of the safety level of organization, safety management, and safety awareness of employee. (author)

Software for computer based systems important to safety in nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

Computer based systems are of increasing importance to safety in nuclear power plants as their use in both new and older plants is rapidly increasing. They are used both in safety related applications, such as some functions of the process control and monitoring systems, as well as in safety critical applications, such as reactor protection or actuation of safety features. The dependability of computer based systems important to safety is therefore of prime interest and should be ensured. With current technology, it is possible in principle to develop computer based instrumentation and control systems for systems important to safety that have the potential for improving the level of safety and reliability with sufficient dependability. However, their dependability can be predicted and demonstrated only if a systematic, fully documented and reviewable engineering process is followed. Although a number of national and international standards dealing with quality assurance for computer based systems important to safety have been or are being prepared, internationally agreed criteria for demonstrating the safety of such systems are not generally available. It is recognized that there may be other ways of providing the necessary safety demonstration than those recommended here. The basic requirements for the design of safety systems for nuclear power plants are provided in the Requirements for Design issued in the IAEA Safety Standards Series.The IAEA has issued a Technical Report to assist Member States in ensuring that computer based systems important to safety in nuclear power plants are safe and properly licensed. The report provides information on current software engineering practices and, together with relevant standards, forms a technical basis for this Safety Guide. The objective of this Safety Guide is to provide guidance on the collection of evidence and preparation of documentation to be used in the safety demonstration for the software for computer based

Software for computer based systems important to safety in nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2005-01-01

Computer based systems are of increasing importance to safety in nuclear power plants as their use in both new and older plants is rapidly increasing. They are used both in safety related applications, such as some functions of the process control and monitoring systems, as well as in safety critical applications, such as reactor protection or actuation of safety features. The dependability of computer based systems important to safety is therefore of prime interest and should be ensured. With current technology, it is possible in principle to develop computer based instrumentation and control systems for systems important to safety that have the potential for improving the level of safety and reliability with sufficient dependability. However, their dependability can be predicted and demonstrated only if a systematic, fully documented and reviewable engineering process is followed. Although a number of national and international standards dealing with quality assurance for computer based systems important to safety have been or are being prepared, internationally agreed criteria for demonstrating the safety of such systems are not generally available. It is recognized that there may be other ways of providing the necessary safety demonstration than those recommended here. The basic requirements for the design of safety systems for nuclear power plants are provided in the Requirements for Design issued in the IAEA Safety Standards Series.The IAEA has issued a Technical Report to assist Member States in ensuring that computer based systems important to safety in nuclear power plants are safe and properly licensed. The report provides information on current software engineering practices and, together with relevant standards, forms a technical basis for this Safety Guide. The objective of this Safety Guide is to provide guidance on the collection of evidence and preparation of documentation to be used in the safety demonstration for the software for computer based

Software for computer based systems important to safety in nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2000-01-01

Computer based systems are of increasing importance to safety in nuclear power plants as their use in both new and older plants is rapidly increasing. They are used both in safety related applications, such as some functions of the process control and monitoring systems, as well as in safety critical applications, such as reactor protection or actuation of safety features. The dependability of computer based systems important to safety is therefore of prime interest and should be ensured. With current technology, it is possible in principle to develop computer based instrumentation and control systems for systems important to safety that have the potential for improving the level of safety and reliability with sufficient dependability. However, their dependability can be predicted and demonstrated only if a systematic, fully documented and reviewable engineering process is followed. Although a number of national and international standards dealing with quality assurance for computer based systems important to safety have been or are being prepared, internationally agreed criteria for demonstrating the safety of such systems are not generally available. It is recognized that there may be other ways of providing the necessary safety demonstration than those recommended here. The basic requirements for the design of safety systems for nuclear power plants are provided in the Requirements for Design issued in the IAEA Safety Standards Series.The IAEA has issued a Technical Report to assist Member States in ensuring that computer based systems important to safety in nuclear power plants are safe and properly licensed. The report provides information on current software engineering practices and, together with relevant standards, forms a technical basis for this Safety Guide. The objective of this Safety Guide is to provide guidance on the collection of evidence and preparation of documentation to be used in the safety demonstration for the software for computer based

Safety evaluation status report for the prototype license application safety analysis report

International Nuclear Information System (INIS)

1989-07-01

The US Nuclear Regulatory Commission (NRC) staff and consultants reviewed a Prototype License Application Safety Analysis Report (PLASAR) submitted by the US Department of Energy (DOE) for the earth-mounded concrete bunker (EMCB) alternative method of low-level radioactive waste disposal. The NRC reviewers relied extensively on the Standard Review Plan (SRP), Rev.1 (NUREG-1200), to evaluate the acceptability of the information provided in the EMCB PLASAR. The NRC staff selected certain review areas in the PLASAR for development of safety evaluation report input to provide examples of safety assessments that are necessary as part of a licensing review. Because of the fictitious nature of the assumed disposal site, and the decision to limit the review to essentially first-round review status, the NRC staff report is labeled a ''Safety Evaluation Status Report'' (SESR). Appendix A comprises the NRC review comments and questions on the information that DOE submitted in the PLASAR. The NRC concentrated its review on the design and operations-related portions of the EMCB PLASAR

Improving the international system for operating experience feedback. INSAG-23. A report by the International Nuclear Safety Group

International Nuclear Information System (INIS)

2008-01-01

The operational safety performance of nuclear facilities has, in general, improved notably over time throughout the world. This has been achieved, in part, through operating experience feedback (OEF) and the introduction of new technology. While the continued strong safety performance by operators is encouraging, safety significant events continue to recur in nuclear installations. This indicates that operators are not learning and applying the lessons that experience can teach us. This report focuses on systems that are operated by intergovernmental organizations with close contacts to national regulatory authorities. These systems provide an alternative network to the worldwide system employed by the operators of nuclear facilities known as the World Association of Nuclear Operators (WANO). The WANO system is restricted to its members, who have concluded that keeping the information exchanged confidential improves its usefulness. INSAG recognizes the merits of this approach, particularly in light of the primary responsibility of licensed operators for the safety of their facilities. Nevertheless, INSAG encourages WANO to share key safety lessons with national regulatory authorities and intergovernmental organization

Report on administrative work for radiation safety from April 2006 to March 2007

Energy Technology Data Exchange (ETDEWEB)

Komori, Akio; Kaneko, Osamu; Nishimura, Kiyohiko; Uda, Tatsuhiko; Asakura, Yamato; Kawano, Takao; Yamanishi, Hirokuni; Miyake, Hitoshi

2007-10-15

The National Institute for Fusion Science (NIFS) is proceeding with the research on magnetic confining nuclear fusion both experimentally and theoretically. During the experiment with deals with very hot plasma, X ray is generated. Therefore the experimental devices with their surroundings are administrated in conformity with the Industrial Safety and Health Law to keep workplace safety. The Radiation Control Safety Office of Safety Hygiene Protection Bureau carries out measuring the radiation dose level regularly, registering the employees who are engaged in plasma experiments, and training them. Non-regulated small sealed sources are used in some detectors. The treating of these sources is controlled by the Safety and Environmental Research Center. This report is on administrative works for radiation safety in the last fiscal year 2006. It includes (1) report on the establishment of radiation safety management system, (2) report on the establishment of training and registration system for radiation workers, and (3) results of radiation dose measurement and monitoring in the radiation controlled area and on the site by using Radiation Monitoring System Applicable to Fusion Experiment (RMSAFE). The report has been published annually. We hope that these reports would be helpful for future safety management in NIFS. (author)

Report on administrative work for radiation safety from April 2006 to March 2007

International Nuclear Information System (INIS)

Komori, Akio; Kaneko, Osamu; Nishimura, Kiyohiko; Uda, Tatsuhiko; Asakura, Yamato; Kawano, Takao; Yamanishi, Hirokuni; Miyake, Hitoshi

2007-10-01

The National Institute for Fusion Science (NIFS) is proceeding with the research on magnetic confining nuclear fusion both experimentally and theoretically. During the experiment with deals with very hot plasma, X ray is generated. Therefore the experimental devices with their surroundings are administrated in conformity with the Industrial Safety and Health Law to keep workplace safety. The Radiation Control Safety Office of Safety Hygiene Protection Bureau carries out measuring the radiation dose level regularly, registering the employees who are engaged in plasma experiments, and training them. Non-regulated small sealed sources are used in some detectors. The treating of these sources is controlled by the Safety and Environmental Research Center. This report is on administrative works for radiation safety in the last fiscal year 2006. It includes (1) report on the establishment of radiation safety management system, (2) report on the establishment of training and registration system for radiation workers, and (3) results of radiation dose measurement and monitoring in the radiation controlled area and on the site by using Radiation Monitoring System Applicable to Fusion Experiment (RMSAFE). The report has been published annually. We hope that these reports would be helpful for future safety management in NIFS. (author)

Review guidelines on software languages for use in nuclear power plant safety systems. Final report

International Nuclear Information System (INIS)

Hecht, H.; Hecht, M.; Graff, S.; Green, W.; Lin, D.; Koch, S.; Tai, A.; Wendelboe, D.

1996-06-01

Guidelines for the programming and auditing of software written in high level languages for safety systems are presented. The guidelines are derived from a framework of issues significant to software safety which was gathered from relevant standards and research literature. Language-specific adaptations of these guidelines are provided for the following high level languages: Ada, C/C++, Programmable Logic Controller (PLC) Ladder Logic, International Electrotechnical Commission (IEC) Standard 1131-3 Sequential Function Charts, Pascal, and PL/M. Appendices to the report include a tabular summary of the guidelines and additional information on selected languages.s

Survey and evaluation of inherent safety characteristics and passive safety systems for use in probabilistic safety analyses

International Nuclear Information System (INIS)

Wetzel, N.; Scharfe, A.

1998-01-01

The present report examines the possibilities and limits of a probabilistic safety analysis to evaluate passive safety systems and inherent safety characteristics. The inherent safety characteristics are based on physical principles, that together with the safety system lead to no damage. A probabilistic evaluation of the inherent safety characteristic is not made. An inventory of passive safety systems of accomplished nuclear power plant types in the Federal Republic of Germany was drawn up. The evaluation of the passive safety system in the analysis of the accomplished nuclear power plant types was examined. The analysis showed that the passive manner of working was always assumed to be successful. A probabilistic evaluation was not performed. The unavailability of the passive safety system was determined by the failure of active components which are necessary in order to activate the passive safety system. To evaluate the passive safety features in new concepts of nuclear power plants the AP600 from Westinghouse, the SBWR from General Electric and the SWR 600 from Siemens, were selected. Under these three reactor concepts, the SWR 600 is specially attractive because the safety features need no energy sources and instrumentation in this concept. First approaches for the assessment of the reliability of passively operating systems are summarized. Generally it can be established that the core melt frequency for the passive concepts AP600 and SBWR is advantageous in comparison to the probabilistic objectives from the European Pressurized Water Reactor (EPR). Under the passive concepts is the SWR 600 particularly interesting. In this concept the passive systems need no energy sources and instrumentation, and has active operational systems and active safety equipment. Siemens argues that with this concept the frequency of a core melt will be two orders of magnitude lower than for the conventional reactors. (orig.) [de

1982 annual status report: reactor safety

International Nuclear Information System (INIS)

1982-01-01

This report presents the projects of the Reactor Safety Program at the JRC: 1) Reliability and risk evolution; 2) LWR loss of coolant accident studies; 3) Primary system integrity; 4) LMFBR core accident initiation and transition phase; and, 5) LMFBR accident post disassembly phase

Fusion safety status report

International Nuclear Information System (INIS)

1986-10-01

This report includes information on a) tritium handling and safety; b) activation product generation and release; c) lithium safety; d) superconducting magnet safety; e) operational safety and shielding; f) environmental impact; g) recycling, decommissioning and waste management; and h) accident analysis. Recommendations for high priority research and development are presented, as well as the current status in each area

National nuclear safety report 2005. Convention on nuclear safety

International Nuclear Information System (INIS)

2006-01-01

This National Nuclear Safety Report was presented at the 3rd. Review meeting. In general the information contained in the report are: Highlights / Themes; Follow-up from 2nd. Review meeting; Challenges, achievements and good practices; Planned measures to improve safety; Updates to National report to 3rd. Review meeting; Questions from peer review of National Report; and Conclusions

Diversity requirements for safety critical software-based automation systems

International Nuclear Information System (INIS)

Korhonen, J.; Pulkkinen, U.; Haapanen, P.

1998-03-01

System vendors nowadays propose software-based systems even for the most critical safety functions in nuclear power plants. Due to the nature and mechanisms of influence of software faults new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)' various safety assessment methods and tools for software based systems are developed and evaluated. This report first discusses the (common cause) failure mechanisms in software-based systems, then defines fault-tolerant system architectures to avoid common cause failures, then studies the various alternatives to apply diversity and their influence on system reliability. Finally, a method for the assessment of diversity is described. Other recently published reports in OHA-report series handles the statistical reliability assessment of software based (STUK-YTO-TR 119), usage models in reliability assessment of software-based systems (STUK-YTO-TR 128) and handling of programmable automation in plant PSA-studies (STUK-YTO-TR 129)

NIKHEF-K safety report 1982

International Nuclear Information System (INIS)

1983-12-01

In this safety report, general information is offered about the safety policy at the NIKHEF-K institute Amsterdam. Costs, prevention, training courses and inspection related to (radiation) safety are briefly discussed. Small accidents are reported. Some measurements have been carried out, but no measurable increase of radiation doses have been found. (Auth.)

Safety and interlock system for Tristan

International Nuclear Information System (INIS)

Takeda, S.; Kudo, K.; Katoh, T.; Akiyama, A.

1987-01-01

This report describes alarm and interlock system of TRISTAN, concentrating on personnel safety. The basis of TRISTAN machine-control system (TMS) is an N-to-N computer network and KEK NODAL which offers high software productivity. TMC achieves high flexibility of operation both for normal operation and for the fast commissioning. However, to assure the safety of personnel and the TRISTAN machine operation, the safety system has to continue functioning during TMC failure as well. A distributed safety and interlock system (DSIS) is used for diversification of risks in TRISTAN system. DSIS is functionally subdivided along local system lines and has a hierarchical structure of 12 programmable sequence controllers (PSCs). Optical fiber links connect the PSCs at subsystem level and a PSC at the supervisory level of TRISTAN central control room (TCCR). The subsystem PSCs provide the interlock functions between their local devices. The local PSCs interact with the central system through a limited number of summarized signals. The central PSC provides the interlock functions between the subsystems and interacts with an operator's panel. Personnel safety is based on a system of electrical interlock keys, emergency push-buttons around the tunnel, at the entrance gates or in the control room

Reliability analysis of Angra I safety systems

International Nuclear Information System (INIS)

Oliveira, L.F.S. de; Soto, J.B.; Maciel, C.C.; Gibelli, S.M.O.; Fleming, P.V.; Arrieta, L.A.

1980-07-01

An extensive reliability analysis of some safety systems of Angra I, are presented. The fault tree technique, which has been successfully used in most reliability studies of nuclear safety systems performed to date is employed. Results of a quantitative determination of the unvailability of the accumulator and the containment spray injection systems are presented. These results are also compared to those reported in WASH-1400. (E.G.) [pt

Sizewell 'B' PWR pre-construction safety report

International Nuclear Information System (INIS)

1982-04-01

The Pre-Construction Safety Report (PCSR) for a PWR power station to be constructed as Sizewell 'B' is presented in 13 volumes containing 16 chapters. The PCSR has been submitted to the Nuclear Installations Inspectorate in support of the Central Electricity Generating Board's application for consent to the extension at Sizewell. It describes the design and provides the safety case for the proposed station, which comprises a 4-loop pressurized water reactor with associated generating plant and supporting auxiliary equipment. A general description of the station and its site is given. The strategy for ensuring nuclear safety is set out and the general design aspects of systems and plant outlined. The plant and systems, including their safety design bases and the fault analyses carried out for the design are described. Finally the way in which the plant will be decommissioned at the end of its useful life is outlined. (U.K.)

Nuclear safety research project (PSF). 1999 annual report

International Nuclear Information System (INIS)

Muehl, B.

2000-08-01

The reactor safety R and D work of the Karlsruhe Research Centre (FZK) has been part of the Nuclear Safety Research Project (PSF) since 1990. The present annual report summarizes the R and D results of PSF during 1999. The research tasks cover three main topics: Light Water Reactor safety, innovative systems, and studies related to the transmutation of actinides. The importance of the Light Water Reactor safety, however, has decreased during the last year in favour of the transmutation of actinides. Numerous institutes of the research centre contribute to the PSF programme, as well as several external partners. The tasks are coordinated in agreement with internal and external working groups. The contributions to this report, which are either written in German or in English, correspond to the status of early/mid 2000. (orig.) [de

Safety studies project on waste management. Final report. Chapters 2 and 3

International Nuclear Information System (INIS)

1985-01-01

The report presents, in summary form, a mode of procedure for accident analysis in nuclear waste management facilities. New instruments for safety analysis have been developed and tested. The report describes exemplary safety analyses with the new instrumentation. The safety analyses were carried out in surface systems, i.e. reprocessing and waste treatment systems, and in underground nuclear waste storage road and rail transport of radioactive materials have been investigated. (EF) [de

An examination of safety reports involving electronic flight bags and portable electronic devices

Science.gov (United States)

2014-06-01

The purpose of this research was to develop a better understanding of safety considerations with the use of Electronic Flight Bags (EFBs) and Portable Electronic Devices (PEDs) by examining safety reports from Aviation Safety Reporting System (ASRS),...

Safety program considerations for space nuclear reactor systems

International Nuclear Information System (INIS)

Cropp, L.O.

1984-08-01

This report discusses the necessity for in-depth safety program planning for space nuclear reactor systems. The objectives of the safety program and a proposed task structure is presented for meeting those objectives. A proposed working relationship between the design and independent safety groups is suggested. Examples of safety-related design philosophies are given

Instrumentation and control systems important to safety in nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2005-01-01

principles should be applied, on the basis of a method of classifying systems by their importance to safety. I and C systems important to safety are I and C systems that are part of a safety group and I and C systems whose malfunction or failure could lead to radiation exposure of site personnel or members of the public. Examples of such systems are: the reactor protection system, reactor control systems, systems to monitor and control normal reactor cooling, systems to monitor and control emergency power supplies, containment isolation systems. The IAEA's Technical Reports Series No. 387 presents an overview of concepts and examples of systems discussed in this Safety Guide and may provide useful background material for some users

System safety education focused on flight safety

Science.gov (United States)

Holt, E.

1971-01-01

The measures necessary for achieving higher levels of system safety are analyzed with an eye toward maintaining the combat capability of the Air Force. Several education courses were provided for personnel involved in safety management. Data include: (1) Flight Safety Officer Course, (2) Advanced Safety Program Management, (3) Fundamentals of System Safety, and (4) Quantitative Methods of Safety Analysis.

Status report on resolution of Waste Tank Safety Issues at the Hanford Site. Revision 1

International Nuclear Information System (INIS)

Dukelow, G.T.; Hanson, G.A.

1995-05-01

The purpose of this report is to provide and update the status of activities supporting the resolution of waste tank safety issues and system deficiencies at the Hanford Site. This report provides: (1) background information on safety issues and system deficiencies; (2) a description of the Tank Waste Remediation System and the process for managing safety issues and system deficiencies; (3) changes in safety issue description, prioritization, and schedules; and (4) a summary of the status, plans, order of magnitude, cost, and schedule for resolving safety issues and system deficiencies

Geosphere process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Skagius, Kristina

2006-09-01

This report documents geosphere processes identified as relevant to the long-term safety of a KBS- repository, and forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The following excerpts describe the methodology, and clarify the role of this process report in the assessment. The repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock and the biosphere in the proximity of the repository, will evolve over time. Future states of the system will depend on the initial state of the system, a number of radiation related, thermal, hydraulic, mechanical, chemical and biological processes acting within the repository system over time, and external influences acting on the system. A methodology in ten steps has been developed for SR-Can described below. Identification of factors to consider (FEP processing): This step consists of identifying all the factors that need to be included in the analysis. Experience from earlier safety assessments and KBS-specific and international databases of relevant features, events and processes influencing long-term safety are utilised. Based on the results of the FEP processing, an SR-Can FEP catalogue, containing FEPs to be handled in SR-Can, has been established. The initial state of the system is described based on the design specifications of the KBS repository, a descriptive model of the repository site and a site-specific layout of the repository. The initial state of the fuel and the engineered components is that immediately after deposition, as described in the SR-Can Initial state report. The initial state of the geosphere and the biosphere is that of the natural system prior to excavation, as described in the site descriptive models. The repository layouts adapted to the sites are provided in underground

Geosphere process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Skagius, Kristina [Kemakta Konsult AB, Stockholm (SE)] (ed.)

2006-09-15

This report documents geosphere processes identified as relevant to the long-term safety of a KBS- repository, and forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The following excerpts describe the methodology, and clarify the role of this process report in the assessment. The repository system, broadly defined as the deposited spent nuclear fuel, the engineered barriers surrounding it, the host rock and the biosphere in the proximity of the repository, will evolve over time. Future states of the system will depend on the initial state of the system, a number of radiation related, thermal, hydraulic, mechanical, chemical and biological processes acting within the repository system over time, and external influences acting on the system. A methodology in ten steps has been developed for SR-Can described below. Identification of factors to consider (FEP processing): This step consists of identifying all the factors that need to be included in the analysis. Experience from earlier safety assessments and KBS-specific and international databases of relevant features, events and processes influencing long-term safety are utilised. Based on the results of the FEP processing, an SR-Can FEP catalogue, containing FEPs to be handled in SR-Can, has been established. The initial state of the system is described based on the design specifications of the KBS repository, a descriptive model of the repository site and a site-specific layout of the repository. The initial state of the fuel and the engineered components is that immediately after deposition, as described in the SR-Can Initial state report. The initial state of the geosphere and the biosphere is that of the natural system prior to excavation, as described in the site descriptive models. The repository layouts adapted to the sites are provided in underground

Probabilistic safety criteria at the safety function/system level

International Nuclear Information System (INIS)

1989-09-01

A Technical Committee Meeting was held in Vienna, Austria, from 26-30 January 1987. The objectives of the meeting were: to review the national developments of PSC at the level of safety functions/systems including future trends; to analyse basic principles, assumptions, and objectives; to compare numerical values and the rationale for choosing them; to compile the experience with use of such PSC; to analyse the role of uncertainties in particular regarding procedures for showing compliance. The general objective of establishing PSC at the level of safety functions/systems is to provide a pragmatic tool to evaluate plant safety which is placing emphasis on the prevention principle. Such criteria could thus lead to a better understanding of the importance to safety of the various functions which have to be performed to ensure the safety of the plant, and the engineering means of performing these functions. They would reflect the state-of-the-art in modern PSAs and could contribute to a balance in system design. This report, prepared by the participants of the meeting, reviews the current status and future trends in the field and should assist Member States in developing their national approaches. The draft of this document was also submitted to INSAG to be considered in its work to prepare a document on safety principles for nuclear power plants. Five papers presented at the meeting are also included in this publication. A separate abstract was prepared for each of these papers. Refs, figs and tabs

Fuel Receiving and Storage Station. Nuclear Regulatory Commission's safety evaluation report

International Nuclear Information System (INIS)

1976-01-01

The safety evaluation report covers design of structures, components, equipment, and systems; nuclear criticality safety; radiological safety; accident analysis; conduct of operations; quality assurance; common defense and security; financial qualifications; financial protection and indemnity requirements; and technical specifications

The Danish patient safety experience: the Act on Patient Safety in the Danish Health care system

DEFF Research Database (Denmark)

Lundgaard, Mette; Rabøl, Louise; Jensen, Elisabeth Agnete Brøgger

2005-01-01

This paper describes the process that lead to the passing of the Act for Patient Safety in the Danisk health care sytem, the contents of the act and how the act is used in the Danish health care system. The act obligates frontline health care personnel to report adverse events, hospital owners...... to act on the reports and the National Board of Health to commuicate the learning nationally. The act protects health care providers from sanctions as a result of reporting. In January 2004, the Act on Patient Safety in the Danish health care system was put into force. In the first twelve months 5740...... adverse events were reported. the reports were analyzed locally (hospital and region), anonymized ad then sent to the National Board af Health. The Act on Patient Safety has driven the work with patient safety forward but there is room for improvement. Continuous and improved feedback from all parts...

Study of reactor parameters of on critical systems, Phase I: Safety report for RB zero power reactor

International Nuclear Information System (INIS)

Raisic, N.

1962-09-01

In addition to the safety analysis for the zero power RB reactor, this report contains a general description of the reactor, reactor components, auxiliary equipment and the reactor building. Reactor Rb has been reconstructed during 1961-1962 and supplied with new safety-control system as well as with a complete dosimetry instrumentation. Since RB reactor was constructed without shielding special attention is devoted to safety and protection of the staff performing experiments. Due to changed circumstances in the Institute ( start-up of the RA 7 MW power reactor) the role of the RB reactor was redefined

33 CFR 96.250 - What documents and reports must a safety management system have?

Science.gov (United States)

2010-07-01

... safety management system have? 96.250 Section 96.250 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY VESSEL OPERATING REGULATIONS RULES FOR THE SAFE OPERATION OF VESSELS AND SAFETY MANAGEMENT SYSTEMS Company and Vessel Safety Management Systems § 96.250 What documents and...

2011 NASA Range Safety Annual Report

Science.gov (United States)

Dumont, Alan G.

2012-01-01

Welcome to the 2011 edition of the NASA Range Safety Annual Report. Funded by NASA Headquarters, this report provides a NASA Range Safety overview for current and potential range users. As is typical with odd year editions, this is an abbreviated Range Safety Annual Report providing updates and links to full articles from the previous year's report. It also provides more complete articles covering new subject areas, summaries of various NASA Range Safety Program activities conducted during the past year, and information on several projects that may have a profound impact on the way business will be done in the future. Specific topics discussed and updated in the 2011 NASA Range Safety Annual Report include a program overview and 2011 highlights; Range Safety Training; Range Safety Policy revision; Independent Assessments; Support to Program Operations at all ranges conducting NASA launch/flight operations; a continuing overview of emerging range safety-related technologies; and status reports from all of the NASA Centers that have Range Safety responsibilities. Every effort has been made to include the most current information available. We recommend this report be used only for guidance and that the validity and accuracy of all articles be verified for updates. Once again the web-based format was used to present the annual report. We continually receive positive feedback on the web-based edition and hope you enjoy this year's product as well. As is the case each year, contributors to this report are too numerous to mention, but we thank individuals from the NASA Centers, the Department of Defense, and civilian organizations for their contributions. In conclusion, it has been a busy and productive year. I'd like to extend a personal Thank You to everyone who contributed to make this year a successful one, and I look forward to working with all of you in the upcoming year.

Physics and safety of transmutation systems. A status report

International Nuclear Information System (INIS)

2006-01-01

The safe and efficient management of spent fuel from the operation of commercial nuclear power plants is an important issue. Worldwide, more than 250 000 tons of spent fuel from currently operating reactors will require disposal. These numbers account for only high-level radioactive waste generated by present-day power reactors. Nearly all issues related to risks to future generations arising from the long-term disposal of such spent nuclear fuel is attributable to only about 1% of its content. This 1% is made up primarily of plutonium, neptunium, americium and curium (called transuranic elements) and the long-lived isotopes of iodine and technetium.When transuranics are removed from discharged fuel destined for disposal, the toxic nature of the spent fuel drops below that of natural uranium ore (that which was originally mined for the nuclear fuel) within a period of several hundred to a thousand years. This significantly reduces the burden on geological repositories and the problem of addressing the remaining long-term residues can thus de done in controlled environments having timescales of centuries rather than millennia stretching beyond 10 000 years. Transmutation is one of the means being explored to address the disposal of transuranic elements. To achieve this, advanced reactors systems, appropriate fuels, separation techniques and associated fuel cycle strategies are required. This status report begins by providing a clear definition of partitioning and transmutation (P and T), and then describes the state of the art concerning the challenges facing the implementation of P and T, scenario studies and specific issues related to accelerator-driven systems (ADS) dynamics and safety, long-lived fission product transmutation and the impact of nuclear data uncertainty on transmutation system design. The report will be of particular interest to nuclear scientists working on P and T issues as well as advanced fuel cycles in general. (author)

Design for safety: theoretical framework of the safety aspect of BIM system to determine the safety index

Directory of Open Access Journals (Sweden)

Ai Lin Evelyn Teo

2016-12-01

Full Text Available Despite the safety improvement drive that has been implemented in the construction industry in Singapore for many years, the industry continues to report the highest number of workplace fatalities, compared to other industries. The purpose of this paper is to discuss the theoretical framework of the safety aspect of a proposed BIM System to determine a Safety Index. An online questionnaire survey was conducted to ascertain the current workplace safety and health situation in the construction industry and explore how BIM can be used to improve safety performance in the industry. A safety hazard library was developed based on the main contributors to fatal accidents in the construction industry, determined from the formal records and existing literature, and a series of discussions with representatives from the Workplace Safety and Health Institute (WSH Institute in Singapore. The results from the survey suggested that the majority of the firms have implemented the necessary policies, programmes and procedures on Workplace Safety and Health (WSH practices. However, BIM is still not widely applied or explored beyond the mandatory requirement that building plans should be submitted to the authorities for approval in BIM format. This paper presents a discussion of the safety aspect of the Intelligent Productivity and Safety System (IPASS developed in the study. IPASS is an intelligent system incorporating the buildable design concept, theory on the detection, prevention and control of hazards, and the Construction Safety Audit Scoring System (ConSASS. The system is based on the premise that safety should be considered at the design stage, and BIM can be an effective tool to facilitate the efforts to enhance safety performance. IPASS allows users to analyse and monitor key aspects of the safety performance of the project before the project starts and as the project progresses.

Aspects of safety and reliability for fusion magnet systems first annual report

International Nuclear Information System (INIS)

Powell, J.

1976-01-01

General systems aspects of fusion magnet safety are examined first, followed by specific detailed analyses covering structural, thermal, electrical, and other aspects of fusion magnet safety. The design examples chosen for analysis are illustrative and are not intended to be definitive, since fusion magnet designs are rapidly evolving. Included is a comprehensive collection of design and operating data relating to the safety of existing superconducting magnet systems. The remainder of the overview lists the main conclusions developed from the work to date. These should be regarded as initial steps. Since this study has concentrated on examining potential safety concerns, it may tend to overemphasize the problems of fusion magnets. In fact, many aspects of fusion magnets are well developed and are consistent with good safety practice. A short summary of the findings of this study is given

Model for safety reports including descriptive examples; Mall foer saekerhetsrapporter med beskrivande exempel

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

Several safety reports will be produced in the process of planning and constructing the system for disposal of high-level radioactive waste in Sweden. The present report gives a model, with detailed examples, of how these reports should be organized and what steps they should include. In the near future safety reports will deal with the encapsulation plant and the repository. Later reports will treat operation of the handling systems and the repository.

Post-licensure safety monitoring of quadrivalent human papillomavirus vaccine in the Vaccine Adverse Event Reporting System (VAERS), 2009-2015.

Science.gov (United States)

Arana, Jorge E; Harrington, Theresa; Cano, Maria; Lewis, Paige; Mba-Jonas, Adamma; Rongxia, Li; Stewart, Brock; Markowitz, Lauri E; Shimabukuro, Tom T

2018-03-20

The Food and Drug Administration (FDA) approved quadrivalent human papillomavirus vaccine (4vHPV) for use in females and males aged 9-26 years, since 2006 and 2009 respectively. We characterized reports to the Vaccine Adverse Event Reporting System (VAERS), a US spontaneous reporting system, in females and males who received 4vHPV vaccination. We searched VAERS for US reports of adverse events (AEs) following 4vHPV from January 2009 through December 2015. Signs and symptoms were coded using Medical Dictionary for Regulatory Activities (MedDRA). We calculated reporting rates and conducted empirical Bayesian data mining to identify disproportional reports. Clinicians reviewed available information, including medical records, and reports of selected pre-specified conditions. VAERS received 19,760 reports following 4vHPV; 60.2% in females, 17.2% in males, and in 22.6% sex was missing. Overall, 94.2% of reports were non-serious; dizziness, syncope and injection site reactions were commonly reported in both males and females. Headache, fatigue and nausea were commonly reported serious AEs. More than 60 million 4vHPV doses were distributed during the study period. Crude AE reporting rates were 327 reports per million 4vHPV doses distributed for all reports, and 19 per million for serious reports. Among 29 verified reports of death, there was no pattern of clustering of deaths by diagnosis, co-morbidities, age, or interval from vaccination to death. No new or unexpected safety concerns or reporting patterns of 4vHPV with clinically important AEs were detected. Safety profile of 4vHPV is consistent with data from pre-licensure trials and postmarketing safety data. Published by Elsevier Ltd.

Guidance for identifying, reporting and tracking nuclear safety noncompliances

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

This document provides Department of Energy (DOE) contractors, subcontractors and suppliers with guidance in the effective use of DOE`s Price-Anderson nuclear safety Noncompliance Tracking System (NTS). Prompt contractor identification, reporting to DOE, and correction of nuclear safety noncompliances provides DOE with a basis to exercise enforcement discretion to mitigate civil penalties, and suspend the issuance of Notices of Violation for certain violations. Use of this reporting methodology is elective by contractors; however, this methodology is intended to reflect DOE`s philosophy on effective identification and reporting of nuclear safety noncompliances. To the extent that these expectations are met for particular noncompliances, DOE intends to appropriately exercise its enforcement discretion in considering whether, and to what extent, to undertake enforcement action.

Guidance for preparation of safety analysis reports for nonreactor facilities and operations

International Nuclear Information System (INIS)

1992-01-01

Department of Energy (DOE) Orders 5480.23, ''Nuclear Safety Analysis Reports,'' and 5481.1B, ''Safety Analysis and Review System'' require the preparation of appropriate safety analyses for each DOE operation and subsequent significant modifications including decommissioning, and independent review of each safety analysis. The purpose of this guide is to assist in the preparation and review of safety documentation for Oak Ridge Field Office (OR) nonreactor facilities and operation. Appendix A lists DOE Orders, NRC Regulatory Guides and other documents applicable to the preparation of safety analysis reports

Plutonium finishing plant safety systems and equipment list

International Nuclear Information System (INIS)

Bergquist, G.G.

1995-01-01

The Safety Equipment List (SEL) supports Analysis Report (FSAR), WHC-SD-CP-SAR-021 and the Plutonium Finishing Plant Operational Safety Requirements (OSRs), WHC-SD-CP-OSR-010. The SEL is a breakdown and classification of all Safety Class 1, 2, and 3 equipment, components, or system at the Plutonium Finishing Plant complex

Bowtie Risk Management methodology and Modern Nuclear Safety Reports

International Nuclear Information System (INIS)

Ilizastigui Pérez, F.

2016-01-01

The Safety Report (SR) plays a crucial role within the nuclear licensing regime as the principal means for demonstrating the adequacy of safety analysis for a nuclear facility to ensure that it can be constructed, operated, maintained, shut down, and decommissioned safely and in compliance with applicable laws and regulations. It serves as the basis for granting authorizations for the commencement of the main stages of the facility’s life cycle as well as decision-making processes related to safety. Historically, the majority of nuclear safety reports have operated under rather prescriptive regimes, with emphasis placed on demonstrations of the robustness of the facility’s design (design safety) against prescriptive technical requirements set by the regulatory body, and less attention paid to demonstrating the adequacy and effectiveness of Operator’s management system for managing risks to daily operation.

Exploring relationships between hospital patient safety culture and Consumer Reports safety scores.

Science.gov (United States)

Smith, Scott Alan; Yount, Naomi; Sorra, Joann

2017-02-16

A number of private and public companies calculate and publish proprietary hospital patient safety scores based on publicly available quality measures initially reported by the U.S. federal government. This study examines whether patient safety culture perceptions of U.S. hospital staff in a large national survey are related to publicly reported patient safety ratings of hospitals. The Agency for Healthcare Research and Quality Hospital Survey on Patient Safety Culture (Hospital SOPS) assesses provider and staff perceptions of hospital patient safety culture. Consumer Reports (CR), a U.S. based non-profit organization, calculates and shares with its subscribers a Hospital Safety Score calculated annually from patient experience survey data and outcomes data gathered from federal databases. Linking data collected during similar time periods, we analyzed relationships between staff perceptions of patient safety culture composites and the CR Hospital Safety Score and its five components using multiple multivariate linear regressions. We analyzed data from 164 hospitals, with patient safety culture survey responses from 140,316 providers and staff, with an average of 856 completed surveys per hospital and an average response rate per hospital of 56%. Higher overall Hospital SOPS composite average scores were significantly associated with higher overall CR Hospital Safety Scores (β = 0.24, p Consumer Reports Hospital Safety Score, which is a composite of patient experience and outcomes data from federal databases. As hospital managers allocate resources to improve patient safety culture within their organizations, their efforts may also indirectly improve consumer-focused, publicly reported hospital rating scores like the Consumer Reports Hospital Safety Score.

National nuclear safety report 1998. Convention on nuclear safety

International Nuclear Information System (INIS)

1998-01-01

The Argentine Republic subscribed the Convention on Nuclear Safety, approved by a Diplomatic Conference in Vienna, Austria, in June 17th, 1994. According to the provisions in Section 5th of the Convention, each Contracting Party shall submit for its examination a National Nuclear Safety Report about the measures adopted to comply with the corresponding obligations. This Report describes the actions that the Argentine Republic is carrying on since the beginning of its nuclear activities, showing that it complies with the obligations derived from the Convention, in accordance with the provisions of its Article 4. The analysis of the compliance with such obligations is based on the legislation in force, the applicable regulatory standards and procedures, the issued licenses, and other regulatory decisions. The corresponding information is described in the analysis of each of the Convention Articles constituting this Report. The present National Report has been performed in order to comply with Article 5 of the Convention on Nuclear Safety, and has been prepared as much as possible following the Guidelines Regarding National Reports under the Convention on Nuclear Safety, approved in the Preparatory Meeting of the Contracting Parties, held in Vienna in April 1997. This means that the Report has been ordered according to the Articles of the Convention on Nuclear Safety and the contents indicated in the guidelines. The information contained in the articles, which are part of the Report shows the compliance of the Argentine Republic, as a contracting party of such Convention, with the obligations assumed

Annual report on occupational safety 1985

International Nuclear Information System (INIS)

1986-09-01

This report presents information on occupational safety relating to the Company's employees for the year 1985, and compares data with figures for the previous year. The following headings are listed: principle activities of BNFL, general policy and organisation, radiological safety, including whole body, skin and extremity, and internal organ doses, non-radiological safety, incidents reportable to the health and safety executive. (U.K.)

Safety applications of computer based systems for the process industry

International Nuclear Information System (INIS)

Bologna, Sandro; Picciolo, Giovanni; Taylor, Robert

1997-11-01

Computer based systems, generally referred to as Programmable Electronic Systems (PESs) are being increasingly used in the process industry, also to perform safety functions. The process industry as they intend in this document includes, but is not limited to, chemicals, oil and gas production, oil refining and power generation. Starting in the early 1970's the wide application possibilities and the related development problems of such systems were recognized. Since then, many guidelines and standards have been developed to direct and regulate the application of computers to perform safety functions (EWICS-TC7, IEC, ISA). Lessons learnt in the last twenty years can be summarised as follows: safety is a cultural issue; safety is a management issue; safety is an engineering issue. In particular, safety systems can only be properly addressed in the overall system context. No single method can be considered sufficient to achieve the safety features required in many safety applications. Good safety engineering approach has to address not only hardware and software problems in isolation but also their interfaces and man-machine interface problems. Finally, the economic and industrial aspects of the safety applications and development of PESs in process plants are evidenced throughout all the Report. Scope of the Report is to contribute to the development of an adequate awareness of these problems and to illustrate technical solutions applied or being developed

Software Safety Risk in Legacy Safety-Critical Computer Systems

Science.gov (United States)

Hill, Janice L.; Baggs, Rhoda

2007-01-01

Safety Standards contain technical and process-oriented safety requirements. Technical requirements are those such as "must work" and "must not work" functions in the system. Process-Oriented requirements are software engineering and safety management process requirements. Address the system perspective and some cover just software in the system > NASA-STD-8719.13B Software Safety Standard is the current standard of interest. NASA programs/projects will have their own set of safety requirements derived from the standard. Safety Cases: a) Documented demonstration that a system complies with the specified safety requirements. b) Evidence is gathered on the integrity of the system and put forward as an argued case. [Gardener (ed.)] c) Problems occur when trying to meet safety standards, and thus make retrospective safety cases, in legacy safety-critical computer systems.

Report of safety of the characterizing system of radioactive waste; Informe de seguridad del sistema caracterizador de desechos radiactivos

Energy Technology Data Exchange (ETDEWEB)

Angeles C, A; Jimenez D, J; Reyes L, J [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)

1998-09-15

Report of safety of the system of radioactive waste of the ININ: Installation, participant personnel, selection of the place, description of the installation, equipment. Proposed activities: operations with radioactive material, calibration in energy, calibration in efficiency, types of waste. Maintenance: handling of radioactive waste, physical safety. Organization: radiological protection, armor-plating, personal dosemeter, risks and emergency plan, environmental impact, medical exams. (Author)

Planning report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-06-01

This document is a planning report for SKB's next assessment of long-term safety for a KBS 3 repository. The assessment, SR-Can, is to be finished by the end of 2005 and will be used for SKB's application to build an Encapsulation plant for spent nuclear fuel. Apart from outlining the methodology, the report discusses the handling in SR-Can of a number of important issues regarding the near field, the geosphere, the biosphere, the climatic evolution etc. The Swedish nuclear safety and radiation protection authorities have recently issued regulations concerning the final disposal of nuclear waste. The principal compliance criterion states that the annual risk of harmful effects must not exceed 10{sup -6} for a representative individual in the group exposed to the greatest risk. There are also a number of requirements on methodological aspects of the safety assessment as well as on the contents of a safety report. The regulations are reproduced in an Appendix to this report. The primary safety function of the KBS 3 system is to completely isolate the spent nuclear fuel within copper canisters over the entire assessment period, which will be one million years in SR-Can. Should a canister be damaged, the secondary safety function is to retard any releases from the canisters. The main steps of the assessment are the following: 1. Qualitative system description, FEP processing: This step consists of defining a system boundary and of describing the system on a format suitable for the safety assessment. Databases of relevant features, events and processes influencing long-term safety are structured and used as one starting point for the assessment. 2. Initial state descriptions. 3. Process descriptions: In this step all identified processes within the system boundary involved in the long-term evolution of the system are described in detail. 4. Description of boundary conditions: This step is a broad description of the evolution of the boundaries of the system

Nuclear Research Center Karlsruhe, Central Safety Department. Annual report 1992

International Nuclear Information System (INIS)

Koelzer, W.

1993-05-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The research and development work concentrates on the following aspects: Physical and chemical behavior of trace elements in the environment, biophysics of multicellular systems, behavior of tritium in the air/soil-plant system, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1992 routine tasks and reports about results of investigations and developments of the working groups of the Department. The reader is referred to the English translation of Chapter 1 describing the duties and organization of the Central Safety Department. (orig.) [de

System Safety in an IT Service Organization

Science.gov (United States)

Parsons, Mike; Scutt, Simon

Within Logica UK, over 30 IT service projects are considered safetyrelated. These include operational IT services for airports, railway infrastructure asset management, nationwide radiation monitoring and hospital medical records services. A recent internal audit examined the processes and documents used to manage system safety on these services and made a series of recommendations for improvement. This paper looks at the changes and the challenges to introducing them, especially where the service is provided by multiple units supporting both safety and non-safety related services from multiple locations around the world. The recommendations include improvements to service agreements, improved process definitions, routine safety assessment of changes, enhanced call logging, improved staff competency and training, and increased safety awareness. Progress is reported as of today, together with a road map for implementation of the improvements to the service safety management system. A proposal for service assurance levels (SALs) is discussed as a way forward to cover the wide variety of services and associated safety risks.

Nature of Blame in Patient Safety Incident Reports: Mixed Methods Analysis of a National Database.

Science.gov (United States)

Cooper, Jennifer; Edwards, Adrian; Williams, Huw; Sheikh, Aziz; Parry, Gareth; Hibbert, Peter; Butlin, Amy; Donaldson, Liam; Carson-Stevens, Andrew

2017-09-01

A culture of blame and fear of retribution are recognized barriers to reporting patient safety incidents. The extent of blame attribution in safety incident reports, which may reflect the underlying safety culture of health care systems, is unknown. This study set out to explore the nature of blame in family practice safety incident reports. We characterized a random sample of family practice patient safety incident reports from the England and Wales National Reporting and Learning System. Reports were analyzed according to prespecified classification systems to describe the incident type, contributory factors, outcomes, and severity of harm. We developed a taxonomy of blame attribution, and we then used descriptive statistical analyses to identify the proportions of blame types and to explore associations between incident characteristics and one type of blame. Health care professionals making family practice incident reports attributed blame to a person in 45% of cases (n = 975 of 2,148; 95% CI, 43%-47%). In 36% of cases, those who reported the incidents attributed fault to another person, whereas 2% of those reporting acknowledged personal responsibility. Blame was commonly associated with incidents where a complaint was anticipated. The high frequency of blame in these safety, incident reports may reflect a health care culture that leads to blame and retribution, rather than to identifying areas for learning and improvement, and a failure to appreciate the contribution of system factors in others' behavior. Successful improvement in patient safety through the analysis of incident reports is unlikely without achieving a blame-free culture. © 2017 Annals of Family Medicine, Inc.

Wind Turbine Generator System Safety and Function Test Report for the Entegrity EW50 Wind Turbine

Energy Technology Data Exchange (ETDEWEB)

Smith, J.; Huskey, A.; Jager, D.; Hur, J.

2012-11-01

This report summarizes the results of a safety and function test that NREL conducted on the Entegrity EW50 wind turbine. This test was conducted in accordance with the International Electrotechnical Commissions' (IEC) standard, Wind Turbine Generator System Part 2: Design requirements for small wind turbines, IEC 61400-2 Ed.2.0, 2006-03.

Development of a Safety Assessment Information System for the Management of Periodic Safety Assessment Activities

International Nuclear Information System (INIS)

Song, Tae Young

2007-01-01

At present, the 10-year Periodic Safety Review(PSR) has been performing to confirm all the aspects of safety issues for all the operating plants in compliance with domestic nuclear law of article 23, subarticle 3. For each plant, in addition, Probabilistic Safety Assessment(PSA) and Severe Accident Management Guideline(SAMG) are being implemented and revised periodically to reflect the latest safety level according to principle fulfillment of severe accident policy statement. The assessment reports, as one of outcomes from these activities, are submitted into and reviewed by domestic regulatory body. During reviewing (in-office duty) and licensing (regulatory duty) process, a large number of outcomes of which most are the formal technical reports and licensing materials, are inevitably produced. Moreover, repeated review process over the plants can make them accumulated and produce a variety of documents additionally. This circumstance motivates to develop effective tool or system for the management of these reports and related technical documents for the future use in licensing process and for subsequent plant assessments. This paper presents the development status of Safety Assessment Information System(SAIS) which manages safety-related documents of PSR, PSA and SAMG for practical use for experienced engineers in charge of these areas

Development of a Safety Assessment Information System for the Management of Periodic Safety Assessment Activities

Energy Technology Data Exchange (ETDEWEB)

Song, Tae Young [Nuclear Engineering and Technology Institute, Daejeon (Korea, Republic of)

2007-07-01

At present, the 10-year Periodic Safety Review(PSR) has been performing to confirm all the aspects of safety issues for all the operating plants in compliance with domestic nuclear law of article 23, subarticle 3. For each plant, in addition, Probabilistic Safety Assessment(PSA) and Severe Accident Management Guideline(SAMG) are being implemented and revised periodically to reflect the latest safety level according to principle fulfillment of severe accident policy statement. The assessment reports, as one of outcomes from these activities, are submitted into and reviewed by domestic regulatory body. During reviewing (in-office duty) and licensing (regulatory duty) process, a large number of outcomes of which most are the formal technical reports and licensing materials, are inevitably produced. Moreover, repeated review process over the plants can make them accumulated and produce a variety of documents additionally. This circumstance motivates to develop effective tool or system for the management of these reports and related technical documents for the future use in licensing process and for subsequent plant assessments. This paper presents the development status of Safety Assessment Information System(SAIS) which manages safety-related documents of PSR, PSA and SAMG for practical use for experienced engineers in charge of these areas.

NASA System Safety Handbook. Volume 2: System Safety Concepts, Guidelines, and Implementation Examples

Science.gov (United States)

Dezfuli, Homayoon; Benjamin, Allan; Everett, Christopher; Feather, Martin; Rutledge, Peter; Sen, Dev; Youngblood, Robert

2015-01-01

This is the second of two volumes that collectively comprise the NASA System Safety Handbook. Volume 1 (NASASP-210-580) was prepared for the purpose of presenting the overall framework for System Safety and for providing the general concepts needed to implement the framework. Volume 2 provides guidance for implementing these concepts as an integral part of systems engineering and risk management. This guidance addresses the following functional areas: 1.The development of objectives that collectively define adequate safety for a system, and the safety requirements derived from these objectives that are levied on the system. 2.The conduct of system safety activities, performed to meet the safety requirements, with specific emphasis on the conduct of integrated safety analysis (ISA) as a fundamental means by which systems engineering and risk management decisions are risk-informed. 3.The development of a risk-informed safety case (RISC) at major milestone reviews to argue that the systems safety objectives are satisfied (and therefore that the system is adequately safe). 4.The evaluation of the RISC (including supporting evidence) using a defined set of evaluation criteria, to assess the veracity of the claims made therein in order to support risk acceptance decisions.

Fusion magnet safety studies program: superconducting magnet protection system and failure. Interim report

International Nuclear Information System (INIS)

Allinger, J.; Danby, G.; Hsieh, S.Y.; Keane, J.; Powell, J.; Prodell, A.

1975-11-01

This report includes the first two quarters study of available information on schemes for protecting superconducting magnets. These schemes can be divided into two different categories. The first category deals with the detection of faulty regions (or normal regions) in the magnet. The second category relates to the protection of the magnet when a fault is detected, and the derived signal which can be used to activate a safety system (or energy removal system). The general detection and protection methods are first described briefly and then followed by a survey of the protection systems used by different laboratories for various magnets. A survey of the cause of the magnet difficulties or failures is also included. A preliminary discussion of these protection schemes and the experimental development of this program is given

1978 annual report of the safety department

International Nuclear Information System (INIS)

Kiefer, H.; Koelzer, W.

1979-04-01

The Safety Officer and the Security Officer, respectively, are responsible for radiation protection and technical safety, both conventional and nuclear, for the physical protection as well as the security of nuclear materials and radioactive substances within the Kernforschungszentrum Karlsruhe GmbH. (KfK). To fulfill these functions they rely on the assitance of the Safety Department. The duties of this Department cover tasks relative to radiation protection, safety and security on behalf of the institutes and departments of KfK and environmental monitoring for the whole Karlsruhe Nuclear Research Center as well as research and development work, mainly performed under the Nuclear Safety Project and the Nuclear Safeguards Project. The centers of interest of r and d activities are: investigation of the atmospheric diffusion of nuclear pollutants on the micro- and meso-scales, evaluation of the radiological consequences of accidents in reactors under probabilistic aspects, studies of the physical and chemical behavior of radionuclides with particularly high biological effectiveness in the environment, implementation of nuclear fuel safequarding systems, improvements in radiation protection measurement technology. This report gives details of the different duties, indicates the results of 1978 routine tasks, and reports about new results of investigations and developments of the working groups of the Department. (orig.) [de

Annual Report 1979 of the Safety Department

International Nuclear Information System (INIS)

Kiefer, H.; Koelzer, W.; Koenig, L.A.

1980-04-01

The Safety Officer and the Security Officer, respectively, are responsible for radiation protection and technical safety, both conventional and nuclear, for the physical protection as well as the security of nuclear materials and radioactive substances within the Kernforschungszentrum Karlsruhe GmbH. (KfK). To fulfill these functions they rely on the assistance of the Safety Department. The duties of this Department cover tasks relative to radiation protection, safety and security on behalf of the institutes and departments of KfK and environmental monitoring for the whole Karlsruhe Nuclear Research Center as well as research and development work, mainly performed under the Nuclear Safety Project and the Nuclear Safeguards Project. The centers of interest of r and d activities are: investigation of the atmospheric diffusion of nuclear pollutants on the micro- and meso-scales, evaluation of the radiological consequences of accidents in reactors under probabilistic aspects, studies of the physical and chemical behavior of radionuclides with particularly high biological effectiveness in the environment, implemantation of nuclear fuel safeguarding systems, improvements in radiation protection measurement technology. This report gives details of the different duties, indicates the results of 1979 routine tasks, and reports about results of investigations and developments of the working groups of the Department. (orig.) [de

Analysis of Aviation Safety Reporting System Incident Data Associated with the Technical Challenges of the Atmospheric Environment Safety Technology Project

Science.gov (United States)

Withrow, Colleen A.; Reveley, Mary S.

2014-01-01

This study analyzed aircraft incidents in the NASA Aviation Safety Reporting System (ASRS) that apply to two of the three technical challenges (TCs) in NASA's Aviation Safety Program's Atmospheric Environment Safety Technology Project. The aircraft incidents are related to airframe icing and atmospheric hazards TCs. The study reviewed incidents that listed their primary problem as weather or environment-nonweather between 1994 and 2011 for aircraft defined by Federal Aviation Regulations (FAR) Parts 121, 135, and 91. The study investigated the phases of flight, a variety of anomalies, flight conditions, and incidents by FAR part, along with other categories. The first part of the analysis focused on airframe-icing-related incidents and found 275 incidents out of 3526 weather-related incidents over the 18-yr period. The second portion of the study focused on atmospheric hazards and found 4647 incidents over the same time period. Atmospheric hazards-related incidents included a range of conditions from clear air turbulence and wake vortex, to controlled flight toward terrain, ground encounters, and incursions.

Interim summary report of the safety case 2009

International Nuclear Information System (INIS)

2010-03-01

Following the guidelines set forth by the Ministry of Trade and Industry (now Ministry of Employment and Economy), Posiva is preparing to submit a construction license application for the final disposal spent nuclear fuel at the Olkiluoto site, Finland, by the end of the year 2012. Disposal will take place in a geological repository implemented according to the KBS-3 method. The long-term safety section supporting the license application will be based on a safety case that, according to the internationally adopted definition, will be a compilation of the evidence, analyses and arguments that quantify and substantiate the safety and the level of expert confidence in the safety of the planned repository. The present Interim Summary Report represents a major contribution to the development of this safety case. The report has been compiled in accordance with Posiva's current plan for preparing this safety case. A full safety case for the KBS-3V variant will be developed to support the Preliminary Safety Assessment Report (PSAR) in 2012. The report outlines the current design and safety concept for the planned repository. It summarises the approach used to formulate scenarios for the evolution of the disposal system over time, describes these scenarios and presents the main models and computer codes used to analyse them. It also discusses compliance with Finnish regulatory requirements for long-term safety of a geological repository and gives the main evidence, arguments and analyses that lead to confidence, on the part of Posiva, in the long-term safety of the planned repository. Current understanding of the evolution of the disposal system indicates that, except a few unlikely circumstances affecting a small number of canisters, spent fuel will remain isolated, and the radionuclides contained within the canisters, for hundreds of thousands of years or more, in accordance with the base scenario. Confidence in this base scenario derives, in the first place, from the

Understanding Nuclear Safety Culture: A Systemic Approach

International Nuclear Information System (INIS)

Afghan, A.N.

2016-01-01

The Fukushima accident was a systemic failure (Report by Director General IAEA on the Fukushima Daiichi Accident). Systemic failure is a failure at system level unlike the currently understood notion which regards it as the failure of component and equipment. Systemic failures are due to the interdependence, complexity and unpredictability within systems and that is why these systems are called complex adaptive systems (CAS), in which “attractors” play an important role. If we want to understand the systemic failures we need to understand CAS and the role of these attractors. The intent of this paper is to identify some typical attractors (including stakeholders) and their role within complex adaptive system. Attractors can be stakeholders, individuals, processes, rules and regulations, SOPs etc., towards which other agents and individuals are attracted. This paper will try to identify attractors in nuclear safety culture and influence of their assumptions on safety culture behavior by taking examples from nuclear industry in Pakistan. For example, if the nuclear regulator is an attractor within nuclear safety culture CAS then how basic assumptions of nuclear plant operators and shift in-charges about “regulator” affect their own safety behavior?

The Interagency Nuclear Safety Review Panel's Galileo safety evaluation report

International Nuclear Information System (INIS)

Nelson, R.C.; Gray, L.B.; Huff, D.A.

1989-01-01

The safety evaluation report (SER) for Galileo was prepared by the Interagency Nuclear Safety Review Panel (INSRP) coordinators in accordance with Presidential directive/National Security Council memorandum 25. The INSRP consists of three coordinators appointed by their respective agencies, the Department of Defense, the Department of Energy (DOE), and the National Aeronautics and Space Administration (NASA). These individuals are independent of the program being evaluated and depend on independent experts drawn from the national technical community to serve on the five INSRP subpanels. The Galileo SER is based on input provided by the NASA Galileo Program Office, review and assessment of the final safety analysis report prepared by the Office of Special Applications of the DOE under a memorandum of understanding between NASA and the DOE, as well as other related data and analyses. The SER was prepared for use by the agencies and the Office of Science and Technology Policy, Executive Office of the Present for use in their launch decision-making process. Although more than 20 nuclear-powered space missions have been previously reviewed via the INSRP process, the Galileo review constituted the first review of a nuclear power source associated with launch aboard the Space Transportation System

Annual report 1985 of the KfK Central Safety Department

International Nuclear Information System (INIS)

Kiefer, H.; Koelzer, W.; Koenig, L.A.

1986-04-01

The Central Safety Department is responsible for handling all problems of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The r+d work concentrates on the following aspects: physical and chemical behavior of biologically particularly active radionuclides, behavior of HT in the air/plant/soil system, biophysics of multicellular systems, improvement in radiation protection measurement and personnel dosimetry. This report gives details of the different duties, indicates the results of 1985 routine tasks and reports about results of investigations and developments of the working groups of the Department. The reader is referred to the English translation of the Table of Contents and of Chapter 1 describing the duties and organization of the Central Safety Department. (orig./HP) [de

Improving patient safety in radiotherapy through error reporting and analysis

International Nuclear Information System (INIS)

Findlay, Ú.; Best, H.; Ottrey, M.

2016-01-01

Aim: To improve patient safety in radiotherapy (RT) through the analysis and publication of radiotherapy errors and near misses (RTE). Materials and methods: RTE are submitted on a voluntary basis by NHS RT departments throughout the UK to the National Reporting and Learning System (NRLS) or directly to Public Health England (PHE). RTE are analysed by PHE staff using frequency trend analysis based on the classification and pathway coding from Towards Safer Radiotherapy (TSRT). PHE in conjunction with the Patient Safety in Radiotherapy Steering Group publish learning from these events, on a triannual and summarised on a biennial basis, so their occurrence might be mitigated. Results: Since the introduction of this initiative in 2010, over 30,000 (RTE) reports have been submitted. The number of RTE reported in each biennial cycle has grown, ranging from 680 (2010) to 12,691 (2016) RTE. The vast majority of the RTE reported are lower level events, thus not affecting the outcome of patient care. Of the level 1 and 2 incidents reported, it is known the majority of them affected only one fraction of a course of treatment. This means that corrective action could be taken over the remaining treatment fractions so the incident did not have a significant impact on the patient or the outcome of their treatment. Analysis of the RTE reports demonstrates that generation of error is not confined to one professional group or to any particular point in the pathway. It also indicates that the pattern of errors is replicated across service providers in the UK. Conclusion: Use of the terminology, classification and coding of TSRT, together with implementation of the national voluntary reporting system described within this report, allows clinical departments to compare their local analysis to the national picture. Further opportunities to improve learning from this dataset must be exploited through development of the analysis and development of proactive risk management strategies

Status of generic actions items and safety analysis system of PHWR

Energy Technology Data Exchange (ETDEWEB)

Park, Joo Hwan; Min, Byung Joo

2001-05-01

This report described the review results of a GAIs(Generic Action Item) currently issued on safety analysis of PHWR(Pressurized Heavy Water Reactor) and the research activities and positions to solve the GAIs in each country which possess PHWRs. eviewing the Final Safety Analysis Report for Wolsong-2/3/4 Units, the safety analysis methodology, classification for accident scenarios, safety analysis codes, their interface, etc.. were described. From the present review report, it is intended to establish the CANDU safety analysis system by providing the better understandings and development plans for the safety analysis of PHWR. esults.

KIT safety management. Annual report 2012

International Nuclear Information System (INIS)

Frank, Gerhard

2013-01-01

The KIT Safety Management Service Unit (KSM) guarantees radiological and conventional technical safety and security of Karlsruhe Institute of Technology and controls the implementation and observation of legal environmental protection requirements. KSM is responsible for - licensing procedures, - industrial safety organization, - control of environmental protection measures, - planning and implementation of emergency preparedness and response, - operation of radiological laboratories and measurement stations, - extensive radiation protection support and the - the execution of security tasks in and for all organizational units of KIT. Moreover, KSM is in charge of wastewater and environmental monitoring for all facilities and nuclear installations all over the KIT campus. KSM is headed by the Safety Commissioner of KIT, who is appointed by the Presidential Committee. Within his scope of procedure for KIT, the Safety Commissioner controls the implementation of and compliance with safety-relevant requirements. The KIT Safety Management is certified according to DIN EN ISO 9001, its industrial safety management is certified by the VBG as ''AMS-Arbeitsschutz mit System'' and, hence, fulfills the requirements of NLF / ISO-OSH 2001. KSM laboratories are accredited according to DIN EN ISO/IEC 17025. To the extent possible, KSM is committed to maintaining competence in radiation protection and to supporting research and teaching activities. The present reports lists the individual tasks of the KIT Safety Management and informs about the results achieved in 2012. Status figures in principle reflect the status at the end of the year 2012. The processes described cover the areas of competence of KSM.

Survey of systems safety analysis methods and their application to nuclear waste management systems

International Nuclear Information System (INIS)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study

Survey of systems safety analysis methods and their application to nuclear waste management systems

Energy Technology Data Exchange (ETDEWEB)

Pelto, P.J.; Winegardner, W.K.; Gallucci, R.H.V.

1981-11-01

This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas for future study.

Safety evaluation report of the Waste Isolation Pilot Plant safety analysis report: Contact-handled transuranic waste disposal operations

International Nuclear Information System (INIS)

1997-02-01

DOE 5480.23, Nuclear Safety Analysis Reports, requires that the US Department of Energy conduct an independent, defensible, review in order to approve a Safety Analysis Report (SAR). That review and the SAR approval basis is documented in this formal Safety Evaluation Report (SER). This SER documents the DOE's review of the Waste Isolation Pilot Plant SAR and provides the Carlsbad Area Office Manager, the WIPP SAR approval authority, with the basis for approving the safety document. It concludes that the safety basis documented in the WIPP SAR is comprehensive, correct, and commensurate with hazards associated with planned waste disposal operations

Critical incidents related to cardiac arrests reported to the Danish Patient Safety Database

DEFF Research Database (Denmark)

Andersen, Peter Oluf; Maaløe, Rikke; Andersen, Henning Boje

2010-01-01

Background Critical incident reports can identify areas for improvement in resuscitation practice. The Danish Patient Safety Database is a mandatory reporting system and receives critical incident reports submitted by hospital personnel. The aim of this study is to identify, analyse and categorize...... critical incidents related to cardiac arrests reported to the Danish Patient Safety Database. Methods The search terms “cardiac arrest” and “resuscitation” were used to identify reports in the Danish Patient Safety Database. Identified critical incidents were then classified into categories. Results One...

Safety evaluation report related to the operation of WPPSS Nuclear Project No. 2, Docket No. 50-397, Washington Public Power Supply System

International Nuclear Information System (INIS)

1982-12-01

Supplement 2 to the Safety Evaluation Report for Washington Public Power Supply System's application for a license to operate WNP-2 (Docket No. 50-397), located in Benton County, Washington, approximately 12 miles north of Richland, Washington, has been prepared by the Office of Nuclear Reactor Regulation of the US Nuclear Regulatory Commission. This supplement reports the status of certain items that had not been resolved at the time of publication of the Safety Evaluation Report and Supplement 1

SCOPE safety-controls optimization by performance evaluation: A systematic approach for safety-related decisions at the Hanford Tank Remediation System. Phase 1, final report

International Nuclear Information System (INIS)

Bergeron, K.D.; Williams, D.C.; Slezak, S.E.; Young, M.L.

1996-12-01

The Department of Energy's Hanford Tank Waste Remediation system poses a significant challenge for hazard management because of the uncertainty that surrounds many of the variables that must be considered in decisions on safety and control strategies. As a result, site managers must often operate under excessively conservative and expensive assumptions. This report describes a systematic approach to quantifying the uncertainties surrounding the critical parameters in control decisions (e.g., condition of the tanks, kinds of wastes, types of possible accidents) through the use of expert elicitation methods. The results of the elicitations would then be used to build a decision support system and accident analysis model that would allow managers to see how different control strategies would affect the cost and safety of a facility configuration

Report on administrative work for radiation safety from April 2004 to March 2006

International Nuclear Information System (INIS)

Uda, Tatsuhiko; Asakura, Yamato; Nishimura, Kiyohiko; Kawano, Takao; Yamanishi, Hirokuni; Miyake, Hitoshi

2006-11-01

The National Institute for Fusion Science (NIFS) constructed the Large Helical Device (LHD) which is the largest magnetic confinement plasma experimental device using a super conducting magnet coils system. The first plasma shot was carried out in March 1998 after eight years of construction. Since then high temperature plasmas and improved plasma confinement experiments have been achieved. On 1st April 2004, NIFS became one of the research institutes which constitute National Institute of Natural Sciences. Since then the regulation system of safety, health and environmental management has been minorly changed. This is a report on administrative work for radiation safety at the LHD and the Compact Helical System (CHS), and radiation measurement and monitoring on the site from 1st April 2004 to 31st March 2006. Major topics are as follows. (1) Establishment of a radiation safety management system based on the law of occupational safety, health and environment. (2) Radiation dose measurement and monitoring in the radiation controlled area and on the site using a particularly developed monitoring system named Radiation Monitoring System Applicable to Fusion Experiments (RMSAFE). (3) Establishment of an education and registration system for radiation workers, and accessing control system for the LHD controlled area. This report has been annually published from fiscal year 1999. We expect that these reports could be helpful for future radiation safety management in NIFS. (author)

Forschungszentrum Rossendorf, Institute for Safety Research. Annual report 1995

International Nuclear Information System (INIS)

Weiss, F.P.; Rindelhardt, U.

1996-09-01

The scientific work of the Institute of Safety Research covers a wide range of safety related investigations. During 1995 important results on thermo-fluid dynamic single effects, thermalhydraulics and neutron kinetics for accident analysis, materials safety, simulation of radiation and particle transport, mechanical integrity of technical systems and process monitoring, risk management for waste deposits, magneto-hydrodynamics of conductive fluids, and of renewable energies were reached. The annual report presents also lists of publications, conference contributions, meetings, and workshops. (DG)

Progress report - reports on reactor safety research programs sponsored by the Federal Ministry for Research and Technology

International Nuclear Information System (INIS)

1982-09-01

Each progress report represents a compilation of individual reports about objectives, the work performed, the results, the next steps of the work etc. The individual reports are prepared in a standard form by the contractors themselves as a documentation of their progress in work and published by the GRS, within the framework of general information of progress in reactor safety research. The individual reports are classified according to the research program on the safety of LWRs 1977-1980 of the BMFT. Another table of contents uses the same classification system as applied in the nuclear safety index of the CEC and the OECD. The reports are arranged in the sequence of their project numbers. (orig./HP) [de

Reactor safety systems

International Nuclear Information System (INIS)

Kafka, P.

1975-01-01

The spectrum of possible accidents may become characterized by the 'maximum credible accident', which will/will not happen. Similary, the performance of safety systems in a multitude of situations is sometimes simplified to 'the emergency system will/will not work' or even 'reactors are/ are not safe'. In assessing safety, one must avoid this fallacy of reducing a complicated situation to the simple black-and-white picture of yes/no. Similarly, there is a natural tendency continually to improve the safety of a system to assure that it is 'safe enough'. Any system can be made safer and there is usually some additional cost. It is important to balance the increased safety against the increased costs. (orig.) [de

Safety significance evaluation system

International Nuclear Information System (INIS)

Lew, B.S.; Yee, D.; Brewer, W.K.; Quattro, P.J.; Kirby, K.D.

1991-01-01

This paper reports that the Pacific Gas and Electric Company (PG and E), in cooperation with ABZ, Incorporated and Science Applications International Corporation (SAIC), investigated the use of artificial intelligence-based programming techniques to assist utility personnel in regulatory compliance problems. The result of this investigation is that artificial intelligence-based programming techniques can successfully be applied to this problem. To demonstrate this, a general methodology was developed and several prototype systems based on this methodology were developed. The prototypes address U.S. Nuclear Regulatory Commission (NRC) event reportability requirements, technical specification compliance based on plant equipment status, and quality assurance assistance. This collection of prototype modules is named the safety significance evaluation system

Reactor system safety assurance

International Nuclear Information System (INIS)

Mattson, R.J.

1984-01-01

The philosophy of reactor safety is that design should follow established and conservative engineering practices, there should be safety margins in all modes of plant operation, special systems should be provided for accidents, and safety systems should have redundant components. This philosophy provides ''defense in depth.'' Additionally, the safety of nuclear power plants relies on ''safety systems'' to assure acceptable response to design basis events. Operating experience has shown the need to study plant response to more frequent upset conditions and to account for the influence of operators and non-safety systems on overall performance. Defense in depth is being supplemented by risk and reliability assessment

Screening of external hazards for NPP with bank type reactor. Modeling of safety related systems and equipment for RBMK. Probabilistic assessment of NPP safety on aircraft impact. Progress report

International Nuclear Information System (INIS)

Kostarev, V.

1999-01-01

This progress report was produced within the frame of IAEA research project on screening the hazards for NPP with bank type reactor. It covers the following tasks; development of the model for the primary loop system of RBMK; developing the models for safety related equipment of RBMK; developing of models for safety related models of EGP-6 type reactor (Bilibinskaya Nuclear Co-generated heat and Power Plant); and probabilistic assessment of NPP safety on aircraft impact

A Fire Safety Certification System for Board and Care Operators and Staff. SBIR Phase II: Final Report.

Science.gov (United States)

Walker, Bonnie L.

This report describes Phase II of a project which developed a system for delivering fire safety training to board and care providers who serve adults with developmental disabilities. Phase II focused on developing and pilot testing a "train the trainers" workshop for instructors and field testing the provider's workshop. Evaluation of…

Assessment of Safety Standards for Automotive Electronic Control Systems

Science.gov (United States)

2016-06-01

This report summarizes the results of a study that assessed and compared six industry and government safety standards relevant to the safety and reliability of automotive electronic control systems. These standards include ISO 26262 (Road Vehicles - ...

NASA System Safety Handbook. Volume 1; System Safety Framework and Concepts for Implementation

Science.gov (United States)

Dezfuli, Homayoon; Benjamin, Allan; Everett, Christopher; Smith, Curtis; Stamatelatos, Michael; Youngblood, Robert

2011-01-01

System safety assessment is defined in NPR 8715.3C, NASA General Safety Program Requirements as a disciplined, systematic approach to the analysis of risks resulting from hazards that can affect humans, the environment, and mission assets. Achievement of the highest practicable degree of system safety is one of NASA's highest priorities. Traditionally, system safety assessment at NASA and elsewhere has focused on the application of a set of safety analysis tools to identify safety risks and formulate effective controls.1 Familiar tools used for this purpose include various forms of hazard analyses, failure modes and effects analyses, and probabilistic safety assessment (commonly also referred to as probabilistic risk assessment (PRA)). In the past, it has been assumed that to show that a system is safe, it is sufficient to provide assurance that the process for identifying the hazards has been as comprehensive as possible and that each identified hazard has one or more associated controls. The NASA Aerospace Safety Advisory Panel (ASAP) has made several statements in its annual reports supporting a more holistic approach. In 2006, it recommended that "... a comprehensive risk assessment, communication and acceptance process be implemented to ensure that overall launch risk is considered in an integrated and consistent manner." In 2009, it advocated for "... a process for using a risk-informed design approach to produce a design that is optimally and sufficiently safe." As a rationale for the latter advocacy, it stated that "... the ASAP applauds switching to a performance-based approach because it emphasizes early risk identification to guide designs, thus enabling creative design approaches that might be more efficient, safer, or both." For purposes of this preface, it is worth mentioning three areas where the handbook emphasizes a more holistic type of thinking. First, the handbook takes the position that it is important to not just focus on risk on an individual

Clinical Trial Electronic Portals for Expedited Safety Reporting: Recommendations from the Clinical Trials Transformation Initiative Investigational New Drug Safety Advancement Project.

Science.gov (United States)

Perez, Raymond P; Finnigan, Shanda; Patel, Krupa; Whitney, Shanell; Forrest, Annemarie

2016-12-15

Use of electronic clinical trial portals has increased in recent years to assist with sponsor-investigator communication, safety reporting, and clinical trial management. Electronic portals can help reduce time and costs associated with processing paperwork and add security measures; however, there is a lack of information on clinical trial investigative staff's perceived challenges and benefits of using portals. The Clinical Trials Transformation Initiative (CTTI) sought to (1) identify challenges to investigator receipt and management of investigational new drug (IND) safety reports at oncologic investigative sites and coordinating centers and (2) facilitate adoption of best practices for communicating and managing IND safety reports using electronic portals. CTTI, a public-private partnership to improve the conduct of clinical trials, distributed surveys and conducted interviews in an opinion-gathering effort to record investigator and research staff views on electronic portals in the context of the new safety reporting requirements described in the US Food and Drug Administration's final rule (Code of Federal Regulations Title 21 Section 312). The project focused on receipt, management, and review of safety reports as opposed to the reporting of adverse events. The top challenge investigators and staff identified in using individual sponsor portals was remembering several complex individual passwords to access each site. Also, certain tasks are time-consuming (eg, downloading reports) due to slow sites or difficulties associated with particular operating systems or software. To improve user experiences, respondents suggested that portals function independently of browsers and operating systems, have intuitive interfaces with easy navigation, and incorporate additional features that would allow users to filter, search, and batch safety reports. Results indicate that an ideal system for sharing expedited IND safety information is through a central portal used by

76 FR 49532 - Federal Motor Vehicle Safety Standards; Electronic Stability Control; Technical Report on the...

Science.gov (United States)

2011-08-10

...-0112] Federal Motor Vehicle Safety Standards; Electronic Stability Control; Technical Report on the Effectiveness of Electronic Stability Control Systems for Cars and LTVs AGENCY: National Highway Traffic Safety..., Electronic Stability Control Systems. The report's title is: Crash Prevention Effectiveness in Light-Vehicle...

Annual activity report of Ignalina NPP Safety Analysis Group for 1996 year

International Nuclear Information System (INIS)

Ushpuras, E.; Augutis, J.; Bubelis, E.

1997-03-01

The main results of Ignalina NPP Safety Analysis Group (ISAG) investigations for 1996 are presented. ISAG is concentrating its research activities into four areas: the neutrons dynamics modelling, simulation of transient processes during loss of coolant accident, the reactor cooling systems modelling and the probabilistic safety assessment of accident confinement system. Ignalina Safety Analysis Report was prepared on the basis of these results. 37 refs., 9 tabs., 96 figs

A Fire Safety Certification System for Board and Care Operators and Staff. SBIR Phase I: Final Report.

Science.gov (United States)

Walker, Bonnie L.

This report describes the development and pilot testing of a fire safety certification system for board and care operators and staff who serve clients with developmental disabilities. During Phase 1, training materials were developed, including a trainer's manual, a participant's coursebook a videotape, an audiotape, and a pre-/post test which was…

Reports on BMBF-sponsored research projects in the field of reactor safety. Reporting period 1 July - 31 December 1995

International Nuclear Information System (INIS)

1996-01-01

The Gesellschaft fuer Anlagen- und Reaktorsicherheit informs of the status of LWR tasks and projects on the safety of advanced reactors. Each progress report represents a compilation of individual reports about objectives, the work performed, the results, and the next steps of the works. The individual reports of quality assurance, safety of reactor component, emergency core cooling, lors of coolant, meltdown, fission product release, risk and reliability, are classified according to projects to the reactor safety research program. Another table uses the same classification system as applied in the nuclear safety index of the CEC. (DG)

Reliability of computerized safety systems at nuclear power plants. Report of a technical committee meeting held in Vienna, 21-25 June 1993

International Nuclear Information System (INIS)

1995-03-01

Computer based technology is increasingly used in order to perform safety functions. In some recently designed nuclear power plants the whole safety system is computerized. In older plants replacement of conventional technology based system is seen to be of benefit. If the new technology is to be used, it must meet at least the same level of quality and reliability requirements as specified for conventional technology. However, there is a potential for enhancing the safety of nuclear power plants if the full power of computer technology is applied correctly through well designed, engineered and tested systems which are properly installed and maintained. It is essential that areas where reliability and quality can be improved are identified and that methods for assessing and assuring reliability are developed. The results of the Technical Committee Meeting on Reliability of Computerized Safety Systems at Nuclear Power Plants presented in this report are a step on the road to this goal of improved nuclear safety. Refs, figs and tabs

Safety and protection for large scale superconducting magnets. FY 1984 report

International Nuclear Information System (INIS)

Thome, R.J.; Pillsbury, R.D. Jr.; Minervini, J.V.

1984-11-01

The Fusion Program is moving rapidly into design and construction of systems using magnets with stored energies in the range of hundreds of megajoules to gigajoules. For example, the toroidal field coil system alone for TFCX would store about 4 GJ and the mirror system MFTF-B would store about 1.6 GJ. Safety and protection analyses of the magnet subsystems become progressively more important as the size and complexity of the installations increase. MIT has been carrying out a program for INEL oriented toward safety and protection in large scale superconducting magnet systems. The program involves collection and analysis of information on actual magnet failures, analyses of general problems associated with safety and protection, and performance of safety oriented experiments. This report summarizes work performed in FY 1984

Injury & Safety Report - Legacy

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Injury & Safety Report is a mandatory post trip legal document observers fill out to report any injuries they have incurred, illnesses they have had, or...

SCOPE safety-controls optimization by performance evaluation: A systematic approach for safety-related decisions at the Hanford Tank Remediation System. Phase 1, final report

Energy Technology Data Exchange (ETDEWEB)

Bergeron, K.D.; Williams, D.C.; Slezak, S.E.; Young, M.L. [and others

1996-12-01

The Department of Energy`s Hanford Tank Waste Remediation system poses a significant challenge for hazard management because of the uncertainty that surrounds many of the variables that must be considered in decisions on safety and control strategies. As a result, site managers must often operate under excessively conservative and expensive assumptions. This report describes a systematic approach to quantifying the uncertainties surrounding the critical parameters in control decisions (e.g., condition of the tanks, kinds of wastes, types of possible accidents) through the use of expert elicitation methods. The results of the elicitations would then be used to build a decision support system and accident analysis model that would allow managers to see how different control strategies would affect the cost and safety of a facility configuration.

Towards the creation of a flexible classification scheme for voluntarily reported transfusion and laboratory safety events.

Science.gov (United States)

Whitehurst, Julie M; Schroder, John; Leonard, Dave; Horvath, Monica M; Cozart, Heidi; Ferranti, Jeffrey

2012-05-18

Transfusion and clinical laboratory services are high-volume activities involving complicated workflows across both ambulatory and inpatient environments. As a result, there are many opportunities for safety lapses, leading to patient harm and increased costs. Organizational techniques such as voluntary safety event reporting are commonly used to identify and prioritize risk areas across care settings. Creation of functional, standardized safety data structures that facilitate effective exploratory examination is therefore essential to drive quality improvement interventions. Unfortunately, voluntarily reported adverse event data can often be unstructured or ambiguously defined. To address this problem, we sought to create a "best-of-breed" patient safety classification for data contained in the Duke University Health System Safety Reporting System (SRS). Our approach was to implement the internationally recognized World Health Organization International Classification for Patient Safety Framework, supplemented with additional data points relevant to our organization. Data selection and integration into the hierarchical framework is discussed, as well as placement of the classification into the SRS. We evaluated the impact of the new SRS classification on system usage through comparisons of monthly average report rates and completion times before and after implementation. Monthly average inpatient transfusion reports decreased from 102.1 ± 14.3 to 91.6 ± 11.2, with the proportion of transfusion reports in our system remaining consistent before and after implementation. Monthly average transfusion report rates in the outpatient and homecare environments were not significantly different. Significant increases in clinical lab report rates were present across inpatient and outpatient environments, with the proportion of lab reports increasing after implementation. Report completion times increased modestly but not significantly from a practical standpoint. A

Review guidelines for software languages for use in nuclear power plant safety systems: Final report. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Hecht, M.; Decker, D.; Graff, S.; Green, W.; Lin, D.; Dinsmore, G.; Koch, S. [SoHaR, Inc., Beverly Hills, CA (United States)

1997-10-01

Guidelines for the programming and auditing of software written in high level languages for safety systems are presented. The guidelines are derived from a framework of issues significant to software safety which was gathered from relevant standards and research literature. Language-specific adaptations of these guidelines are provided for the following high level languages: Ada83 and Ada95; C and C++; International Electrochemical Commission (IEC) Standard 1131-3 Ladder Logic, Sequential Function Charts, Structured Text, and Function Block Diagrams; Pascal; and PL/M. Appendices to the report include a tabular summary of the guidelines and additional information on selected languages.

Review guidelines for software languages for use in nuclear power plant safety systems: Final report. Revision 1

International Nuclear Information System (INIS)

Hecht, M.; Decker, D.; Graff, S.; Green, W.; Lin, D.; Dinsmore, G.; Koch, S.

1997-10-01

Guidelines for the programming and auditing of software written in high level languages for safety systems are presented. The guidelines are derived from a framework of issues significant to software safety which was gathered from relevant standards and research literature. Language-specific adaptations of these guidelines are provided for the following high level languages: Ada83 and Ada95; C and C++; International Electrochemical Commission (IEC) Standard 1131-3 Ladder Logic, Sequential Function Charts, Structured Text, and Function Block Diagrams; Pascal; and PL/M. Appendices to the report include a tabular summary of the guidelines and additional information on selected languages

PRACA Enhancement Pilot Study Report: Engineering for Complex Systems Program (formerly Design for Safety), DFS-IC-0006

Science.gov (United States)

Korsmeyer, David; Schreiner, John

2002-01-01

This technology evaluation report documents the findings and recommendations of the Engineering for Complex Systems Program (formerly Design for Safety) PRACA Enhancement Pilot Study of the Space Shuttle Program's (SSP's) Problem Reporting and Corrective Action (PRACA) System. A team at NASA Ames Research Center (ARC) performed this Study. This Study was initiated as a follow-on to the NASA chartered Shuttle Independent Assessment Team (SIAT) review (performed in the Fall of 1999) which identified deficiencies in the current PRACA implementation. The Pilot Study was launched with an initial qualitative assessment and technical review performed during January 2000 with the quantitative formal Study (the subject of this report) started in March 2000. The goal of the PRACA Enhancement Pilot Study is to evaluate and quantify the technical aspects of the SSP PRACA systems and recommend enhancements to address deficiencies and in preparation for future system upgrades.

Annual report on occupational safety 1987

International Nuclear Information System (INIS)

1988-01-01

This report presents detailed information on occupational safety relating to the Company's employees for 1987. Data are quoted in tables and text, together with data from the previous year for comparison where available. The report is presented under the following headings: radiological and non-radiological safety, incidents, appendices (statutory dose limits, nuclear incident criteria for reporting to ministers). (author)

Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. National Report from Norway

International Nuclear Information System (INIS)

2006-05-01

This report is the Norwegian report to the second review meeting to the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management. The comments, questions and remarks given to Norway's initial national report and Norway's presentation given at the first review meeting have been incorporated in this report. The second report is a full revision of the first report. This report concludes that Norway meets the obligations of the Joint Convention. However, Norwegian authorities will aim for development in the waste management policy and Norway will continue to improve its existing systems to further enhance safety, in line with the aims of the Joint Convention

Development of Non-safety System Architecture and Evaluation of Components/Systems

International Nuclear Information System (INIS)

Oh, I. S.; Lee, C. K.; Kim, D. H.; Lee, J. W.; Lee, D. Y.; Park, W. M.; Hwang, I. K.; Hur, S.; Kim, J. T.; Park, J. C.; Lee, J. W.

2007-10-01

We describe in this report the works performed for a technical evaluation of the non-safety digital control system of the KNICS, the non-safety process control system of the KNICS, a communication load analysis for the MMIS (including both the non-safety and the safety systems) of the KNICS, the development of MMI and an implementation of the logic for the CVCS, and the works performed to support writing a proposal needed for bidding an I and C system based on the KNICS. The technical evaluation results were aimed to be used by the designers to detect parts needed to be corrected or to be newly inserted, and also by the developers during the development phase. The requirement specifications and the data requirement characteristics have been identified for each subsystem of the determined KNICS structure. For each communication node, the specifications related to the data transfer including the data capacity for interfaces, delay time for the data transfer, and the marginal availability of its performance capabilities have been analyzed to identify the amount of data transfer and hence to verify that both of the designed structures for the safety related communications network and for the digital communications network are appropriate. The results of the supporting work performed for writing the technical specifications related to each subsystem of the KNICS structure, are expected to be useful in writing a proposal for the expected Uljin new units 1 and 2, and in the I and C upgrade for any of the existing nuclear power plants under operation. Also included in this report are the descriptions on a design of the chemical volume control system (CVCS), on the supporting work performed to draw the logic diagrams for CVCS using the tool ISaGRAF, and on the generation of a set of system displays to be used as references

Development of Non-safety System Architecture and Evaluation of Components/Systems

Energy Technology Data Exchange (ETDEWEB)

Oh, I. S.; Lee, C. K.; Kim, D. H.; Lee, J. W.; Lee, D. Y.; Park, W. M.; Hwang, I. K.; Hur, S.; Kim, J. T.; Park, J. C.; Lee, J. W

2007-10-15

We describe in this report the works performed for a technical evaluation of the non-safety digital control system of the KNICS, the non-safety process control system of the KNICS, a communication load analysis for the MMIS (including both the non-safety and the safety systems) of the KNICS, the development of MMI and an implementation of the logic for the CVCS, and the works performed to support writing a proposal needed for bidding an I and C system based on the KNICS. The technical evaluation results were aimed to be used by the designers to detect parts needed to be corrected or to be newly inserted, and also by the developers during the development phase. The requirement specifications and the data requirement characteristics have been identified for each subsystem of the determined KNICS structure. For each communication node, the specifications related to the data transfer including the data capacity for interfaces, delay time for the data transfer, and the marginal availability of its performance capabilities have been analyzed to identify the amount of data transfer and hence to verify that both of the designed structures for the safety related communications network and for the digital communications network are appropriate. The results of the supporting work performed for writing the technical specifications related to each subsystem of the KNICS structure, are expected to be useful in writing a proposal for the expected Uljin new units 1 and 2, and in the I and C upgrade for any of the existing nuclear power plants under operation. Also included in this report are the descriptions on a design of the chemical volume control system (CVCS), on the supporting work performed to draw the logic diagrams for CVCS using the tool ISaGRAF, and on the generation of a set of system displays to be used as references.

Quantitative risk assessment of digitalized safety systems

Energy Technology Data Exchange (ETDEWEB)

Shin, Sung Min; Lee, Sang Hun; Kang, Hym Gook [KAIST, Daejeon (Korea, Republic of); Lee, Seung Jun [UNIST, Ulasn (Korea, Republic of)

2016-05-15

A report published by the U.S. National Research Council indicates that appropriate methods for assessing reliability are key to establishing the acceptability of digital instrumentation and control (I and C) systems in safety-critical plants such as NPPs. Since the release of this issue, the methodology for the probabilistic safety assessment (PSA) of digital I and C systems has been studied. However, there is still no widely accepted method. Kang and Sung found three critical factors for safety assessment of digital systems: detection coverage of fault-tolerant techniques, software reliability quantification, and network communication risk. In reality the various factors composing digitalized I and C systems are not independent of each other but rather closely connected. Thus, from a macro point of view, a method that can integrate risk factors with different characteristics needs to be considered together with the micro approaches to address the challenges facing each factor.

Safety regulations for radioisotopes, etc. (interim report)

International Nuclear Information System (INIS)

1980-01-01

An (interim) report by an ad hoc expert committee to the Nuclear Safety Commission, on the safety regulations for radioisotopes, etc., was presented. For the utilization of radioisotopes, etc., there is the Law Concerning Prevention of Radiation Injury Due to Radioisotopes, etc. with the advances in this field and the improvement in international standards, the regulations by the law have been examined. After explaining the basic ideas of the regulations, the problems and countermeasures in the current regulations are described: legal system, rationalization in permission procedures and others, inspection on RI management, the system of the persons in charge of radiation handling, RI transport, low-level radioactive wastes, consumer goods, definitions of RIs, radiation and sealed sources, regulations by group partitioning, RI facilities, system of personnel exposure registration, entrusting of inspection, etc. to private firms, and reduction in the works for permission among governmental offices. (author)

Results from synthesis of calculation cases illustrating overall system performance in the safety assessment in H12 report

International Nuclear Information System (INIS)

Makino, Hitoshi; Sawada, Atsushi; Wakasugi, Keiichiro; Kato, Tomoko; Uchida, Masahiro; Miyahara, Kaname

2002-02-01

JNC (Japan Nuclear Cycle Development Institute) had proceeded R and D activities to provide a scientific and technical basis for geological disposal of HLW in Japan. The second progress report (H12) documented the progress of R and D and the Japanese version was submitted to the AEC (the Atomic Energy Commission) in November 1999. This report summarizes the calculation results for nuclide migration in 'Synthesis of Calculation Cases Illustrating Overall System Performance', which are performed to examine the safety of the geological disposal concept in Japan in the Safety Assessment in H12 Report. In addition, a set of calculation result for nuclide migration through each pathway in one-dimensional multiple pathway model (a set of 48 segments) are summarized for the Reference Case in H12 Report, and calculated dose conversion factors are also summarized against the combinations of potential Geosphere-Biosphere Interfaces (GBI) and potential exposure groups. Digital data of the calculation results are summarized in Appendix CD-ROM as Microsoft EXCEL files. (author)

Institute for Safety Research. Annual report 1992

International Nuclear Information System (INIS)

Weiss, F.P.; Boehmert, J.

1993-11-01

The Institute is concerned with evaluating the design based safety and increasing the operational safety of technical systems which include serious sources of danger. It is further occupied with methods of mitigating the effects of incidents and accidents. For all these goals the institute does research work in the following fields: modelling and simulation of thermofluid dynamics and neutron kinetics in cases of accidents; two-phase measuring techniques; safety-related analyses and characterizing of mechanical behaviours of material; measurements and calculations of radiation fields; process and plant diagnostics; development and application of methods of decision analysis. This annual report gives a survey of projects and scientific contributions (e.g. Single rod burst tests with ZrNb1 cladding), lists publications, institute seminars and workshops, names the personal staff and describes the organizational structure. (orig./HP)

Quality and Safety Education for Nurses (QSEN): The Key is Systems Thinking.

Science.gov (United States)

Dolansky, Mary A; Moore, Shirley M

2013-09-30

Over a decade has passed since the Institute of Medicine's reports on the need to improve the American healthcare system, and yet only slight improvement in quality and safety has been reported. The Quality and Safety Education for Nurses (QSEN) initiative was developed to integrate quality and safety competencies into nursing education. The current challenge is for nurses to move beyond the application of QSEN competencies to individual patients and families and incorporate systems thinking in quality and safety education and healthcare delivery. This article provides a history of QSEN and proposes a framework in which systems thinking is a critical aspect in the application of the QSEN competencies. We provide examples of how using this framework expands nursing focus from individual care to care of the system and propose ways to teach and measure systems thinking. The conclusion calls for movement from personal effort and individual care to a focus on care of the system that will accelerate improvement of healthcare quality and safety.

Licensing process for safety-critical software-based systems

Energy Technology Data Exchange (ETDEWEB)

Haapanen, P. [VTT Automation, Espoo (Finland); Korhonen, J. [VTT Electronics, Espoo (Finland); Pulkkinen, U. [VTT Automation, Espoo (Finland)

2000-12-01

System vendors nowadays propose software-based technology even for the most critical safety functions in nuclear power plants. Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)', financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. As a part of the OHA-work a reference model for the licensing process for software-based safety automation systems is defined. The licensing process is defined as the set of interrelated activities whose purpose is to produce and assess evidence concerning the safety and reliability of the system/application to be licensed and to make the decision about the granting the construction and operation permissions based on this evidence. The parties of the licensing process are the authority, the licensee (the utility company), system vendors and their subcontractors and possible external independent assessors. The responsibility about the production of the evidence in first place lies at the licensee who in most cases rests heavily on the vendor expertise. The evaluation and gauging of the evidence is carried out by the authority (possibly using external experts), who also can acquire additional evidence by using their own (independent) methods and tools. Central issue in the licensing process is to combine the quality evidence about the system development process with the information acquired through tests, analyses and operational experience. The purpose of the licensing process described in this report is to act as a reference model both for the authority and the licensee when planning the licensing of individual applications

Licensing process for safety-critical software-based systems

International Nuclear Information System (INIS)

Haapanen, P.; Korhonen, J.; Pulkkinen, U.

2000-12-01

System vendors nowadays propose software-based technology even for the most critical safety functions in nuclear power plants. Due to the nature of software faults and the way they cause system failures new methods are needed for the safety and reliability evaluation of these systems. In the research project 'Programmable automation systems in nuclear power plants (OHA)', financed together by the Radiation and Nuclear Safety Authority (STUK), the Ministry of Trade and Industry (KTM) and the Technical Research Centre of Finland (VTT), various safety assessment methods and tools for software based systems are developed and evaluated. As a part of the OHA-work a reference model for the licensing process for software-based safety automation systems is defined. The licensing process is defined as the set of interrelated activities whose purpose is to produce and assess evidence concerning the safety and reliability of the system/application to be licensed and to make the decision about the granting the construction and operation permissions based on this evidence. The parties of the licensing process are the authority, the licensee (the utility company), system vendors and their subcontractors and possible external independent assessors. The responsibility about the production of the evidence in first place lies at the licensee who in most cases rests heavily on the vendor expertise. The evaluation and gauging of the evidence is carried out by the authority (possibly using external experts), who also can acquire additional evidence by using their own (independent) methods and tools. Central issue in the licensing process is to combine the quality evidence about the system development process with the information acquired through tests, analyses and operational experience. The purpose of the licensing process described in this report is to act as a reference model both for the authority and the licensee when planning the licensing of individual applications. Many of the

Traceability of Software Safety Requirements in Legacy Safety Critical Systems

Science.gov (United States)

Hill, Janice L.

2007-01-01

How can traceability of software safety requirements be created for legacy safety critical systems? Requirements in safety standards are imposed most times during contract negotiations. On the other hand, there are instances where safety standards are levied on legacy safety critical systems, some of which may be considered for reuse for new applications. Safety standards often specify that software development documentation include process-oriented and technical safety requirements, and also require that system and software safety analyses are performed supporting technical safety requirements implementation. So what can be done if the requisite documents for establishing and maintaining safety requirements traceability are not available?

Safety evaluation report related to the preliminary design of the Standard Reference System, RESAR-414

International Nuclear Information System (INIS)

1978-11-01

The safety evaluation for the Westinghouse Standard Reactor includes information on general reactor characteristics; design criteria for systems and components; reactor coolant system; engineered safety systems; instrumentation and controls; electric power systems; auxiliary systems; steam and power conversion system; radioactive waste management; radiation protection; conduct of operations; accident analyses; and quality assurance

Use of computational fluid dynamics codes for safety analysis of nuclear reactor systems, including containment. Summary report of a technical meeting

International Nuclear Information System (INIS)

2003-11-01

Safety analysis is an important tool for justifying the safety of nuclear power plants. Typically, this type of analysis is performed by means of system computer codes with one dimensional approximation for modelling real plant systems. However, in the nuclear area there are issues for which traditional treatment using one dimensional system codes is considered inadequate for modelling local flow and heat transfer phenomena. There is therefore increasing interest in the application of three dimensional computational fluid dynamics (CFD) codes as a supplement to or in combination with system codes. There are a number of both commercial (general purpose) CFD codes as well as special codes for nuclear safety applications available. With further progress in safety analysis techniques, the increasing use of CFD codes for nuclear applications is expected. At present, the main objective with respect to CFD codes is generally to improve confidence in the available analysis tools and to achieve a more reliable approach to safety relevant issues. An exchange of views and experience can facilitate and speed up progress in the implementation of this objective. Both the International Atomic Energy Agency (IAEA) and the Nuclear Energy Agency of the Organisation for Economic Co-operation and Development (OECD/NEA) believed that it would be advantageous to provide a forum for such an exchange. Therefore, within the framework of the Working Group on the Analysis and Management of Accidents of the NEA's Committee on the Safety of Nuclear Installations, the IAEA and the NEA agreed to jointly organize the Technical Meeting on the Use of Computational Fluid Dynamics Codes for Safety Analysis of Reactor Systems, including Containment. The meeting was held in Pisa, Italy, from 11 to 14 November 2002. The publication constitutes the report of the Technical Meeting. It includes short summaries of the presentations that were made and of the discussions as well as conclusions and

Enhancing nuclear safety. Annual report 2014. Financial report 2014

International Nuclear Information System (INIS)

2015-01-01

After some introductory texts proposed by several IRSN head managers, and a brief presentation of some key data illustrating the activity, the annual report presents the main strategic orientations, notably in the field of knowledge management, and of information and communication. After some images illustrating the past year, activities are presented. They first deal with safety: Reactor safety (operating experience feedback), From decommissioning old reactors to designing those of the future, Safety of laboratories and plants, Safety regarding risks due to infrastructure near nuclear facilities, Reactor aging, Fuel: research on corrosion and deformation, Research and assessments for improved understanding of accident situations, Earthquakes: research and assessments, About defense, Geological disposal of radioactive waste. They secondly deal with security and non-proliferation (nuclear security, nuclear non-proliferation, chemical weapon ban), thirdly with radiation protection for human and environment health (environment monitoring, radionuclide transfer in the environment, radon and polluted sites, human exposure, radiation protection in the workplace, effects of low-dose chronic exposures, Organization of radiation protection at the European level, protection in health care), and fourthly with emergency and post-accident situations (emergency and post-accident preparedness and response, Emergency response tools). The next part of the activity report addresses issues related to efficiency: Real estate program (construction projects get started), Hygiene, safety, social responsibility, Human resources, Organization chart, Board of directors, Steering committee for the nuclear defense expertise Division - CODEND, Scientific council, Ethics commission composition, Nuclear safety and radiation protection Research policy committee - COR. The financial report proposes a management report, financial statements with an appendix to annual accounts, and an auditor

Additional safety assessments. Report by the Nuclear Safety Authority - December 2011

International Nuclear Information System (INIS)

2011-12-01

The first part of this voluminous report proposes an assessment of targeted audits performed in French nuclear installations (water pressurized reactors on the one hand, laboratories, factories and waste and dismantling installations on the other hand) on issues related to the Fukushima accident. The examined issues were the protection against flooding and against earthquake, and the loss of electricity supplies and of cooling sources. The second part addresses the additional safety assessments of the reactors and the European resistance tests: presentation of the French electronuclear stock, earthquake, flooding and natural hazards (installation sizing, safety margin assessment), loss of electricity supplies and cooling systems, management of severe accidents, subcontracting conditions. The third part addresses the same issues for nuclear installations other than nuclear power reactors

Incorporation of advanced accident analysis methodology into safety analysis reports

International Nuclear Information System (INIS)

2003-05-01

The IAEA Safety Guide on Safety Assessment and Verification defines that the aim of the safety analysis should be by means of appropriate analytical tools to establish and confirm the design basis for the items important to safety, and to ensure that the overall plant design is capable of meeting the prescribed and acceptable limits for radiation doses and releases for each plant condition category. Practical guidance on how to perform accident analyses of nuclear power plants (NPPs) is provided by the IAEA Safety Report on Accident Analysis for Nuclear Power Plants. The safety analyses are performed both in the form of deterministic and probabilistic analyses for NPPs. It is customary to refer to deterministic safety analyses as accident analyses. This report discusses the aspects of using the advanced accident analysis methods to carry out accident analyses in order to introduce them into the Safety Analysis Reports (SARs). In relation to the SAR, purposes of deterministic safety analysis can be further specified as (1) to demonstrate compliance with specific regulatory acceptance criteria; (2) to complement other analyses and evaluations in defining a complete set of design and operating requirements; (3) to identify and quantify limiting safety system set points and limiting conditions for operation to be used in the NPP limits and conditions; (4) to justify appropriateness of the technical solutions employed in the fulfillment of predetermined safety requirements. The essential parts of accident analyses are performed by applying sophisticated computer code packages, which have been specifically developed for this purpose. These code packages include mainly thermal-hydraulic system codes and reactor dynamics codes meant for the transient and accident analyses. There are also specific codes such as those for the containment thermal-hydraulics, for the radiological consequences and for severe accident analyses. In some cases, codes of a more general nature such

Nuclear Reactor RA Safety Report, Vol. 14, Safety protection measures

International Nuclear Information System (INIS)

1986-11-01

Nuclear reactor accidents can be caused by three type of errors: failure of reactor components including (1) control and measuring instrumentation, (2) errors in operation procedure, (3) natural disasters. Safety during reactor operation are secured during its design and construction and later during operation. Both construction and administrative procedures are applied to attain safe operation. Technical safety features include fission product barriers, fuel elements cladding, primary reactor components (reactor vessel, primary cooling pipes, heat exchanger in the pump), reactor building. Safety system is the system for safe reactor shutdown and auxiliary safety system. RA reactor operating regulations and instructions are administrative acts applied to avoid possible human error caused accidents [sr

Lessons learned on digital systems safety

International Nuclear Information System (INIS)

Sivertsen, Terje

2005-06-01

A decade ago, in 1994, lessons learned from Halden research activities on digital systems safety were summarized in the reports HWR-374 and HWR-375, under the title 'A Lessons Learned Report on Software Dependability'. The reports reviewed all activities made at the Halden Project in this field since 1977. As such, the reports provide a wealth of information on Halden research. At the same time, the lessons learned from the different activities are made more accessible to the reader by being summarized in terms of results, conclusions and recommendations. The present report provides a new lessons learned report, covering the Halden Project research activities in this area from 1994 to medio 2005. As before, the emphasis is on the results, conclusions and recommendations made from these activities, in particular how they can be utilized by different types of organisations, such as licensing authorities, safety assessors, power companies, and software developers. The contents of the report have been edited on the basis of input from a large number of Halden work reports, involving many different authors. Brief summaries of these reports are included in the last part of the report. (Author)

Report on safety related occurrences and reactor trips July 1, 1976-December 31, 1976

International Nuclear Information System (INIS)

Andermo, L.

1977-04-01

This is a systematically arranged report on all reported safety related occurrences and reactor trips in Swedish nuclear power plants in operation during July 1, 1976 to December 31, 1976 inclusive. The facilities involved are Oskarshamn 1 and 2, Ringhals 1 and 2 and Barsebaeck 1. During this period of the 6 months 37 safety related occurrences and 34 reactor trips have been reported to the Nuclear Power Inspectorate. As earlier experiences have shown it is to the greatest extent the conventional components which bring about the safety related occurrences or occurrences leading to outages or power reductions. However, the component errors discovered in the safety related systems have not affected the function of their redundant systems and other diverse systems have not been involved. Therefore the reactor safety has been satisfactory. The fact that even small deviations from prescribed operation results in automatic and safe shut down of the reactor, does not always imply a conflict with operational availability. The number of reactor trips are almost as low as during the last period, which is a drastic reduction compared to earlier time periods. The greatest outages are caused by occurrences without safety significance.(author)

System and safety studies of accelerator driven transmutation systems. Annual report 1998

International Nuclear Information System (INIS)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K.

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project 'Impact of the accelerator based technologies on nuclear fission safety' - IABAT and in bilateral cooperation with different foreign research groups

System and safety studies of accelerator driven transmutation systems. Annual report 1998

Energy Technology Data Exchange (ETDEWEB)

Wallenius, J.; Gudowski, W.; Carlsson, Johan; Eriksson, Marcus; Tucek, K. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

1998-12-01

This annual report describes the accelerator-driven transmutation project conducted at the Department of Nuclear and Reactor Physics at the Royal Institute of Technology. The main results are: development of the simulation tools for accelerator-driven transmutation calculations including an integrated Monte-Carlo burnup module and improvements of neutron energy fission yield simulations, processing of the evacuated nuclear data files including preparation of the temperature dependent neutron cross-sections, development of nuclear data for a medium energy range for some isotopes, development of the models and codes for radiation damage simulations, system studies for the spent fuel transmuter, based on heavy metal coolant and advanced nuclear fuel, contribution to the spallation target design being manufactured in IPPE, Obninsk, and accelerator reliability studies. Moreover a lot of efforts were put to further develop existing international collaboration with the most active research groups in the world together with educational activities in Sweden including a number of meetings and workshops and a graduate course in transmutation. This project has been conducted in close collaboration with the EU-project `Impact of the accelerator based technologies on nuclear fission safety` - IABAT and in bilateral cooperation with different foreign research groups 31 refs, 23 figs

Safety and health annual report 1996

International Nuclear Information System (INIS)

1997-01-01

The 1996 report on the Health and Safety performance of the nuclear fuel cycle company BNFL at its sites in the United Kingdom demonstrates a continuing improvement. The site locations and developments are briefly described and international developments in subsidiary organisations noted. Other sections of the report cover health and safety policy, radiological and industrial safety, emergency planning, incidents, occupational health services, compensation scheme developments, transport, putting radiation in perspective, and safety and health research. Data are provided on: radioactive discharges; industrial safety of BNFL and contractors' employees; radiation dose summaries for BNFL and contractors' employees. There is evidence of the expected plateauing out of doses to BNFL employees at a level less than or similar to background radiation. (UK)

Safety design guide for safety related systems for CANDU 9

International Nuclear Information System (INIS)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young; A. C. D. Wright

1996-03-01

In general, two types of safety related systems and structures exist in the nuclear plant; The one is a systems and structures which perform safety functions during the normal operation of the plant, and the other is a systems and structures which perform safety functions to mitigate events caused by failure of the normally operating systems or by naturally occurring phenomena. In this safety design guide, these systems are identified in detail, and the major events for which the safety functions are required and the major safety requirements are identified in the list. As the probabilistic safety assessments are completed during the course of the project, additions or deletions to the list may be justified. 3 tabs. (Author) .new

Safety design guide for safety related systems for CANDU 9

Energy Technology Data Exchange (ETDEWEB)

Lee, Duk Su; Chang, Woo Hyun; Lee, Nam Young [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of); Wright, A.C.D. [Atomic Energy of Canada Ltd., Toronto (Canada)

1996-03-01

In general, two types of safety related systems and structures exist in the nuclear plant; The one is a systems and structures which perform safety functions during the normal operation of the plant, and the other is a systems and structures which perform safety functions to mitigate events caused by failure of the normally operating systems or by naturally occurring phenomena. In this safety design guide, these systems are identified in detail, and the major events for which the safety functions are required and the major safety requirements are identified in the list. As the probabilistic safety assessments are completed during the course of the project, additions or deletions to the list may be justified. 3 tabs. (Author) .new.

Report on administrative work for radiation safety from April 2010 to March 2011

International Nuclear Information System (INIS)

Nishimura, Kiyohiko; Uda, Tatsuhiko; Asakura, Yamato; Kawano, Takao; Yamanishi, Hirokuni; Miyake, Hitoshi; Tanaka, Masahiro

2011-12-01

The National Institute for Fusion Science (NIFS) is proceeding with basic research on magnetic nuclear fusion which is expected to be a perpetual energy source for the future. Because the object of research is a hot plasma, high energy particles which are elements of the plasma generate X-rays. Therefore we administrate the devices and their surroundings in conformity with the Industrial Safety and Health Law to maintain workplace safety. We measure the radiation dose levels regularly, register the employees who are engaged in plasma experiments, and educate them. We also control the handling of non-regulated small sealed sources that are used in the detectors in some cases. This report is on administrative work for radiation safety in the last fiscal year 2010. It includes (1) a report on the establishment of a radiation safety management system, (2) results of radiation dose measurement and monitoring in the radiation controlled area and on the site by using Radiation Monitoring System Applicable to Fusion Experiment (RMSAFE), (3) a report on the establishment of an education and registration system for radiation workers. (author)

76 FR 12300 - Safety Management System for Certificated Airports; Extension of Comment Period

Science.gov (United States)

2011-03-07

...-0997; Notice No. 10-14] RIN 2120-AJ38 Safety Management System for Certificated Airports; Extension of...: Background On October 7, 2010, the FAA published Notice No. 10-14, entitled ``Safety Management System for... conclusions from the safety management systems proof of concept. The FAA anticipates making this report...

Planning report for the safety assessment SR-Can

International Nuclear Information System (INIS)

2003-06-01

This document is a planning report for SKB's next assessment of long-term safety for a KBS 3 repository. The assessment, SR-Can, is to be finished by the end of 2005 and will be used for SKB's application to build an Encapsulation plant for spent nuclear fuel. Apart from outlining the methodology, the report discusses the handling in SR-Can of a number of important issues regarding the near field, the geosphere, the biosphere, the climatic evolution etc. The Swedish nuclear safety and radiation protection authorities have recently issued regulations concerning the final disposal of nuclear waste. The principal compliance criterion states that the annual risk of harmful effects must not exceed 10 -6 for a representative individual in the group exposed to the greatest risk. There are also a number of requirements on methodological aspects of the safety assessment as well as on the contents of a safety report. The regulations are reproduced in an Appendix to this report. The primary safety function of the KBS 3 system is to completely isolate the spent nuclear fuel within copper canisters over the entire assessment period, which will be one million years in SR-Can. Should a canister be damaged, the secondary safety function is to retard any releases from the canisters. The main steps of the assessment are the following: 1. Qualitative system description, FEP processing: This step consists of defining a system boundary and of describing the system on a format suitable for the safety assessment. Databases of relevant features, events and processes influencing long-term safety are structured and used as one starting point for the assessment. 2. Initial state descriptions. 3. Process descriptions: In this step all identified processes within the system boundary involved in the long-term evolution of the system are described in detail. 4. Description of boundary conditions: This step is a broad description of the evolution of the boundaries of the system, focussing mainly

Safety study of PCC 2140 and ALILOG 21 used as part of safety measurement systems

International Nuclear Information System (INIS)

Meriaux, Pierre; Adnot, Serge; Rayrolles, Catherine.

1978-03-01

The PCC 2140 and ALILOG 21 equipment may be used at C.E.A. or E.D.F., as part of safety measurement systems. In a study of a similar, but earlier equipment, it was noticed that certain types of failures caused the system to switch to the least sensitive measurement range, which was detrimental to safety. This report analyses failure modes leading to unsafe failures and evaluates the risks ran into taking in account tests during use [fr

Patient-Reported Safety Information: A Renaissance of Pharmacovigilance?

Science.gov (United States)

Härmark, Linda; Raine, June; Leufkens, Hubert; Edwards, I Ralph; Moretti, Ugo; Sarinic, Viola Macolic; Kant, Agnes

2016-10-01

The role of patients as key contributors in pharmacovigilance was acknowledged in the new EU pharmacovigilance legislation. This contains several efforts to increase the involvement of the general public, including making patient adverse drug reaction (ADR) reporting systems mandatory. Three years have passed since the legislation was introduced and the key question is: does pharmacovigilance yet make optimal use of patient-reported safety information? Independent research has shown beyond doubt that patients make an important contribution to pharmacovigilance signal detection. Patient reports provide first-hand information about the suspected ADR and the circumstances under which it occurred, including medication errors, quality failures, and 'near misses'. Patient-reported safety information leads to a better understanding of the patient's experiences of the ADR. Patients are better at explaining the nature, personal significance and consequences of ADRs than healthcare professionals' reports on similar associations and they give more detailed information regarding quality of life including psychological effects and effects on everyday tasks. Current methods used in pharmacovigilance need to optimise use of the information reported from patients. To make the most of information from patients, the systems we use for collecting, coding and recording patient-reported information and the methodologies applied for signal detection and assessment need to be further developed, such as a patient-specific form, development of a severity grading and evolution of the database structure and the signal detection methods applied. It is time for a renaissance of pharmacovigilance.

Safety management as a foundation for evidence-based aeromedical standards and reporting of medical events.

Science.gov (United States)

Evans, Anthony D; Watson, Dougal B; Evans, Sally A; Hastings, John; Singh, Jarnail; Thibeault, Claude

2009-06-01

The different interpretations by States (countries) of the aeromedical standards established by the International Civil Aviation Organization has resulted in a variety of approaches to the development of national aeromedical policy, and consequently a relative lack of harmonization. However, in many areas of aviation, safety management systems have been recently introduced and may represent a way forward. A safety management system can be defined as "A systematic approach to managing safety, including the necessary organizational structures, accountabilities, policies, and procedures" (1). There are four main areas where, by applying safety management principles, it may be possible to better use aeromedical data to enhance flight safety. These are: 1) adjustment of the periodicity and content of routine medical examinations to more accurately reflect aeromedical risk; 2) improvement in reporting and analysis of routine medical examination data; 3) improvement in reporting and analysis of in-flight medical events; and 4) support for improved reporting of relevant aeromedical events through the promotion of an appropriate culture by companies and regulatory authorities. This paper explores how the principles of safety management may be applied to aeromedical systems to improve their contribution to safety.

IAEA Safety Standards on Management Systems and Safety Culture

International Nuclear Information System (INIS)

Persson, Kerstin Dahlgren

2007-01-01

The IAEA has developed a new set of Safety Standard for applying an integrated Management System for facilities and activities. The objective of the new Safety Standards is to define requirements and provide guidance for establishing, implementing, assessing and continually improving a Management System that integrates safety, health, environmental, security, quality and economic related elements to ensure that safety is properly taken into account in all the activities of an organization. With an integrated approach to management system it is also necessary to include the aspect of culture, where the organizational culture and safety culture is seen as crucial elements of the successful implementation of this management system and the attainment of all the goals and particularly the safety goals of the organization. The IAEA has developed a set of service aimed at assisting it's Member States in establishing. Implementing, assessing and continually improving an integrated management system. (author)

Risk-based rules for crane safety systems

Energy Technology Data Exchange (ETDEWEB)

Ruud, Stian [Section for Control Systems, DNV Maritime, 1322 Hovik (Norway)], E-mail: Stian.Ruud@dnv.com; Mikkelsen, Age [Section for Lifting Appliances, DNV Maritime, 1322 Hovik (Norway)], E-mail: Age.Mikkelsen@dnv.com

2008-09-15

The International Maritime Organisation (IMO) has recommended a method called formal safety assessment (FSA) for future development of rules and regulations. The FSA method has been applied in a pilot research project for development of risk-based rules and functional requirements for systems and components for offshore crane systems. This paper reports some developments in the project. A method for estimating target reliability for the risk-control options (safety functions) by means of the cost/benefit decision criterion has been developed in the project and is presented in this paper. Finally, a structure for risk-based rules is proposed and presented.

Risk-based rules for crane safety systems

International Nuclear Information System (INIS)

Ruud, Stian; Mikkelsen, Age

2008-01-01

The International Maritime Organisation (IMO) has recommended a method called formal safety assessment (FSA) for future development of rules and regulations. The FSA method has been applied in a pilot research project for development of risk-based rules and functional requirements for systems and components for offshore crane systems. This paper reports some developments in the project. A method for estimating target reliability for the risk-control options (safety functions) by means of the cost/benefit decision criterion has been developed in the project and is presented in this paper. Finally, a structure for risk-based rules is proposed and presented

Safety culture in design. Final report

International Nuclear Information System (INIS)

Macchi, L.; Pietikaeinen, E.; Liinasuo, M.; Savioja, P.; Reiman, T.; Wahlstroem, M.; Kahlbom, U.; Rollenhagen, C.

2013-04-01

In this report we approach design from a safety culture approach As this research area is new and understudied, we take a wide scope on the issue. Different theoretical perspectives that can be taken when improving safety of the design process are considered in this report. We suggest that in the design context the concept of safety culture should be expanded from an organizational level to the level of the network of organizations involved in the design activity. The implication of approaching the design process from a safety culture perspective are discussed and the results of the empirical part of the research are presented. In the interview study in Finland and Sweden we identified challenges and opportunities in the design process from safety culture perspective. Also, a small part of the interview study concentrated on state of the art human factors engineering (HFE) practices in Finland and the results relating to that are presented. This report provide a basis for future development of systematic good design practices and for providing guidelines that can lead to safe and robust technical solutions. (Author)

Safety culture in design. Final report

Energy Technology Data Exchange (ETDEWEB)

Macchi, L.; Pietikaeinen, E.; Liinasuo, M.; Savioja, P.; Reiman, T.; Wahlstroem, M. [VTT Technical Research Centre of Finland, Espoo (Finland); Kahlbom, U. [Risk Pilot AB, Stockholm (Sweden); Rollenhagen, C. [Vattenfall, Stockholm, (Sweden)

2013-04-15

In this report we approach design from a safety culture approach As this research area is new and understudied, we take a wide scope on the issue. Different theoretical perspectives that can be taken when improving safety of the design process are considered in this report. We suggest that in the design context the concept of safety culture should be expanded from an organizational level to the level of the network of organizations involved in the design activity. The implication of approaching the design process from a safety culture perspective are discussed and the results of the empirical part of the research are presented. In the interview study in Finland and Sweden we identified challenges and opportunities in the design process from safety culture perspective. Also, a small part of the interview study concentrated on state of the art human factors engineering (HFE) practices in Finland and the results relating to that are presented. This report provide a basis for future development of systematic good design practices and for providing guidelines that can lead to safe and robust technical solutions. (Author)

Supplement report to the Nuclear Criticality Safety Handbook of Japan

International Nuclear Information System (INIS)

Okuno, Hiroshi; Komuro, Yuichi; Nakajima, Ken

1995-10-01

Supplementing works to 'The Nuclear Criticality Safety Handbook' of Japan have been continued since 1988, the year the handbook edited by the Science and Technology Agency first appeared. This report publishes the fruits obtained in the supplementing works. Substantial improvements are made in the chapters of 'Modelling the evaluation object' and 'Methodology for analytical safety assessment', and newly added are chapters of 'Criticality safety of chemical processes', 'Criticality accidents and their evaluation methods' and 'Basic principles on design and installation of criticality alarm system'. (author)

Buff book 1: status summary report, water reactor safety research

International Nuclear Information System (INIS)

1980-01-01

This Management Report, to provide information for monitoring and controlling the progress of LWR Safety Research Projects Associated with the Office of Nuclear Regulatory Research and other agencies and organizations engaged in nuclear safety research. It utilizes data pertaining to project schedules, cost, and status which have been integrated into a network-based management information system, The purpose of this publication is to provide a vehicle for review of the current status and overall progress of the safety Research Program from a managerial point of view

Karlsruhe Nuclear Research Center, Central Safety Department. Annual report 1993

International Nuclear Information System (INIS)

Koelzer, W.

1994-04-01

The Central Safety Department is responsible for handling all tasks of radiation protection, safety and security of the institutes and departments of the Karlsruhe Nuclear Research Center, for waste water activity measurements and environmental monitoring of the whole area of the Center, and for research and development work mainly focusing on nuclear safety and radiation protection measures. The research and development work concentrates on the following aspects: behavior of trace elements in the environment and decontamination of soil, behavior of tritium in the air/soil-plant system, improvement in radiation protection measurements and personnel dosimetry. This report gives details of the different duties, indicates the results of 1993 routine tasks and reports about results of investigations and developments of the working groups of the Department. (orig.) [de

Safety of High Speed Ground Transportation Systems : Analytical Methodology for Safety Validation of Computer Controlled Subsystems : Volume 2. Development of a Safety Validation Methodology

Science.gov (United States)

1995-01-01

This report describes the development of a methodology designed to assure that a sufficiently high level of safety is achieved and maintained in computer-based systems which perform safety cortical functions in high-speed rail or magnetic levitation ...

Annual health, safety and environmental performance report for 1992

International Nuclear Information System (INIS)

Orman, R.F.; Richards, S.

1993-12-01

This report summarizes the safety and environmental record of the operations of Atomic Energy of Canada Limited (AECL) during 1992. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices

Annual health, safety and environmental performance report for 1992

International Nuclear Information System (INIS)

Orman, R.F.; Richards, S.

1993-12-01

This report summarizes the safety and environmental record of the operations of Atomic Energy of Canada Limited (AECL) during 1992. an introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices

Ventilator-Related Adverse Events: A Taxonomy and Findings From 3 Incident Reporting Systems.

Science.gov (United States)

Pham, Julius Cuong; Williams, Tamara L; Sparnon, Erin M; Cillie, Tam K; Scharen, Hilda F; Marella, William M

2016-05-01

In 2009, researchers from Johns Hopkins University's Armstrong Institute for Patient Safety and Quality; public agencies, including the FDA; and private partners, including the Emergency Care Research Institute and the University HealthSystem Consortium (UHC) Safety Intelligence Patient Safety Organization, sought to form a public-private partnership for the promotion of patient safety (P5S) to advance patient safety through voluntary partnerships. The study objective was to test the concept of the P5S to advance our understanding of safety issues related to ventilator events, to develop a common classification system for categorizing adverse events related to mechanical ventilators, and to perform a comparison of adverse events across different adverse event reporting systems. We performed a cross-sectional analysis of ventilator-related adverse events reported in 2012 from the following incident reporting systems: the Pennsylvania Patient Safety Authority's Patient Safety Reporting System, UHC's Safety Intelligence Patient Safety Organization database, and the FDA's Manufacturer and User Facility Device Experience database. Once each organization had its dataset of ventilator-related adverse events, reviewers read the narrative descriptions of each event and classified it according to the developed common taxonomy. A Pennsylvania Patient Safety Authority, FDA, and UHC search provided 252, 274, and 700 relevant reports, respectively. The 3 event types most commonly reported to the UHC and the Pennsylvania Patient Safety Authority's Patient Safety Reporting System databases were airway/breathing circuit issue, human factor issues, and ventilator malfunction events. The top 3 event types reported to the FDA were ventilator malfunction, power source issue, and alarm failure. Overall, we found that (1) through the development of a common taxonomy, adverse events from 3 reporting systems can be evaluated, (2) the types of events reported in each database were related

Ventilator-Related Adverse Events: A Taxonomy and Findings From 3 Incident Reporting Systems

Science.gov (United States)

Pham, Julius Cuong; Williams, Tamara L; Sparnon, Erin M; Cillie, Tam K; Scharen, Hilda F; Marella, William M

2016-01-01

BACKGROUND: In 2009, researchers from Johns Hopkins University's Armstrong Institute for Patient Safety and Quality; public agencies, including the FDA; and private partners, including the Emergency Care Research Institute and the University HealthSystem Consortium (UHC) Safety Intelligence Patient Safety Organization, sought to form a public-private partnership for the promotion of patient safety (P5S) to advance patient safety through voluntary partnerships. The study objective was to test the concept of the P5S to advance our understanding of safety issues related to ventilator events, to develop a common classification system for categorizing adverse events related to mechanical ventilators, and to perform a comparison of adverse events across different adverse event reporting systems. METHODS: We performed a cross-sectional analysis of ventilator-related adverse events reported in 2012 from the following incident reporting systems: the Pennsylvania Patient Safety Authority's Patient Safety Reporting System, UHC's Safety Intelligence Patient Safety Organization database, and the FDA's Manufacturer and User Facility Device Experience database. Once each organization had its dataset of ventilator-related adverse events, reviewers read the narrative descriptions of each event and classified it according to the developed common taxonomy. RESULTS: A Pennsylvania Patient Safety Authority, FDA, and UHC search provided 252, 274, and 700 relevant reports, respectively. The 3 event types most commonly reported to the UHC and the Pennsylvania Patient Safety Authority's Patient Safety Reporting System databases were airway/breathing circuit issue, human factor issues, and ventilator malfunction events. The top 3 event types reported to the FDA were ventilator malfunction, power source issue, and alarm failure. CONCLUSIONS: Overall, we found that (1) through the development of a common taxonomy, adverse events from 3 reporting systems can be evaluated, (2) the types of

Development of the Digital Reactor Safety System

International Nuclear Information System (INIS)

Lee, Dong Young; Lee, C. K.; Hwang, I. K.

2008-04-01

Objectives of Project - Development of Digital Safety Grade PLC and Licensing - Development of Safety System(RPS) and Licensing - Development of Safety System(ESF-CCS) and Licensing Content and Result of Project - POSAFE-Q PLC : Development of PLC platform for Shin-UCN unit 1 and 2 ·Development Scope : Processor module, Power module, 3 kinds of Communication module, Bus extension module(Master and Slave), 16 kinds of Input and Output module ·PLC application software development tool(pSET) - IDiPS RPS and IDiPS ESF-CCS : Development of PPS for Sin-UCN 1 and 2 ·Development Scope - 4-channels RPS with the KNICS inherent architecture - A part of 1-channels ESF-CCS with the KNICS inherent architecture - Licensing ·optical Report Submitted and Expected to finish the licensing process until Aug. 2008

Development and implementation of setpoint tolerances for special safety systems

International Nuclear Information System (INIS)

Oliva, A.F.; Balog, G.; Parkinson, D.G.; Archinoff, G.H.

1991-01-01

The establishment of tolerances and impairment limits for special safety system setpoints is part of the process whereby the plant operator demonstrates to the regulatory authority that the plant operates safely and within the defined plant licensing envelope. The licensing envelope represents the set of limits and plant operating state and for which acceptably safe plant operation has been demonstrated by the safety analysis. By definition, operation beyond this envelope contributes to overall safety system unavailability. Definition of the licensing envelope is provided in a wide range of documents including the plant operating licence, the safety report, and the plant operating policies and principles documents. As part of the safety analysis, limits are derived for each special safety system initiating parameter such that the relevant safety design objectives are achieved for all design basis events. If initiation on a given parameter occurs at a level beyond its limit, there is a potential reduction in safety system effectiveness relative to the performance credited in the plant safety analysis. These safety system parameter limits, when corrected for random and systematic instrument errors and other errors inherent in the process of periodic testing or calibration, are then used to derive parameter impairment levels and setpoint tolerances. This paper describes the methodology that has evolved at Ontario Hydro for developing and implementing tolerances for special safety system parameters (i.e., the shutdown systems, emergency coolant injection system and containment system). Tolerances for special safety system initiation setpoints are addressed specifically, although many of the considerations discussed here will apply to performance limits for other safety system components. The first part of the paper deals with the approach that has been adopted for defining and establishing setpoint limits and tolerances. The remainder of the paper addresses operational

Safety logic systems of PFBR

International Nuclear Information System (INIS)

Sambasivan, S. Ilango

2004-01-01

Full text : PFBR is provided with two independent, fast acting and diverse shutdown systems to detect any abnormalities and to initiate safety action. Each system consists of sensors, signal processing systems, logics, drive mechanisms and absorber rods. The absorber rods of the first system are Control and Safety Rods (CSR) and that of the second are called as Diverse Safety Rods (DSR). There are nine CSR and three DSR. While CSR are used for startup, control of reactor power, controlled shutdown and SCRAM, the DSR are used only for SCRAM. The respective drive mechanisms are called as CSRDM and DSRDM. Each of these two systems is capable of executing the shutdown satisfactorily with single failure criteria. Two independent safety logic systems based on diverse principles have been designed for the two shut down systems. The analog outputs of the sensors of Core Monitoring Systems comprising of reactor flux monitoring, core temperature monitoring, failed fuel detection and core flow monitoring systems are processed and converted into binary signals depending on their instantaneous values. Safety logic systems receive the binary signals from these core-monitoring systems and process them logically to protect the reactor against postulated initiating events. Neutronic and power to flow (P/Q) signals form the inputs to safety logic system-I and temperature signals are inputs to the safety logic system II. Failed fuel detection signals are processed by both the shut down systems. The two logic systems to actuate the safety rods are also based on two diverse designs and implemented with solid-state devices to meet all the requirements of safety systems. Safety logic system I that caters to neutronic and P/Q signals is designed around combinational logic and has an on-line test facility to detect struck at faults. The second logic system is based on dynamic logic and hence is inherently safe. This paper gives an overview of the two logic systems that have been

Chemical Safety Vulnerability Working Group Report

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

This report marks the culmination of a 4-month review conducted to identify chemical safety vulnerabilities existing at DOE facilities. This review is an integral part of DOE's efforts to raise its commitment to chemical safety to the same level as that for nuclear safety.

Operating experience feedback report - Air systems problems

International Nuclear Information System (INIS)

Ornstein, H.L.

1987-12-01

This report highlights significant operating events involving observed or potential failures of safety-related systems in U.S. plants that resulted from degraded or malfunctioning non-safety grade air systems. Based upon the evaluation of these events, the Office for Analysis and Evaluation of Operational Data (AEOD) concludes that the issue of air systems problems is an important one which requires additional NRC and industry attention. This report also provides AEOD's recommendations for corrective actions to deal with the issue. (author)

Improving the regulation of safety at DOE nuclear facilities. Final report

International Nuclear Information System (INIS)

1995-12-01

The report strongly recommends that, with the end of the Cold War, safety and health at DOE facilities should be regulated by outside agencies rather than by DOE itself. The three major recommendations are: under any regulatory scheme, DOE must maintain a strong internal safety management system; essentially all aspects of safety at DOE's nuclear facilities should be externally regulated; and existing agencies rather than a new one should be responsible for external regulation

Patient safety event reporting in critical care: a study of three intensive care units.

Science.gov (United States)

Harris, Carolyn B; Krauss, Melissa J; Coopersmith, Craig M; Avidan, Michael; Nast, Patricia A; Kollef, Marin H; Dunagan, W Claiborne; Fraser, Victoria J

2007-04-01

To increase patient safety event reporting in three intensive care units (ICUs) using a new voluntary card-based event reporting system and to compare and evaluate observed differences in reporting among healthcare workers across ICUs. Prospective, single-center, interventional study. A medical ICU (19 beds), surgical ICU (24 beds), and cardiothoracic ICU (17 beds) at a 1,371-bed urban teaching hospital. Adult patients admitted to these three study ICUs. Use of a new, internally designed, card-based reporting program to solicit voluntary anonymous reporting of medical errors and patient safety concerns. During a 14-month period, 714 patient safety events were reported using a new card-based reporting system, reflecting a significant increase in reporting compared with pre-intervention Web-based reporting (20.4 reported events/1,000 patient days pre-intervention to 41.7 reported events/1,000 patient days postintervention; rate ratio, 2.05; 95% confidence interval, 1.79-2.34). Nurses submitted the majority of reports (nurses, 67.1%; physicians, 23.1%; other reporters, 9.5%); however, physicians experienced the greatest increase in reporting among their group (physicians, 43-fold; nurses, 1.7-fold; other reporters, 4.3-fold) relative to pre-intervention rates. There were significant differences in the reporting of harm by job description: 31.1% of reports from nurses, 36.2% from other staff, and 17.0% from physicians described events that did not reach/affect the patient (p = .001); and 33.9% of reports from physicians, 27.2% from nurses, and 13.0% from other staff described events that caused harm (p = .005). Overall reported patient safety events per 1,000 patient days differed by ICU (medical ICU = 55.5, cardiothoracic ICU = 25.3, surgical ICU = 40.2; p reporting system increased reporting significantly compared with pre-intervention Web-based reporting and revealed significant differences in reporting by healthcare worker and ICU. These differences may reveal

Report on safety related occurrences and reactor trips July 1, 1979 - December 31, 1979

International Nuclear Information System (INIS)

Olsson, S.; Andermo, L.

1980-01-01

This is a report on all reported safety related occurrences and reactor trips in Swedish nuclear power plants in operation during July 1 to December 31, 1979 inclusive. The facilities involved are Barsebaeck 1 and 2, Oskarshamn 1 and 2 and Ringhals 1 and 2. During this period of 6 months 76 safety related occurrences and 27 reactor trips have been reported to the Nuclear Power Inspectorate. It is to the greatest extent conventional components such as valves and pumps which bring about the safety related occurrences or occurrences leading to outages or power reductions. However, the component errors discovered in the safety related systems have not affected the function of their redundant system and other diverse systems have not been involved. Therefore the reactor safety has been satisfactory. The total number of reactor trips are normal. The average value for these 6 months is 4.5 trips/unit. Approximetely one half of the reactor trips happened at zero or very low power operation. The fact that even small deviations from prescribed operation result in an automatic and safe shut down of the reactor, does not always imply a conflict with operational availability. The greatest outages are caused by occurrences without safety significance. (author)

Safety of mechanical devices. Safety of automation systems

International Nuclear Information System (INIS)

Pahl, G.; Schweizer, G.; Kapp, K.

1985-01-01

The paper deals with the classic procedures of safety engineering in the sectors mechanical engineering, electrical and energy engineering, construction and transport, medicine technology and process technology. Particular stress is laid on the safety of automation systems, control technology, protection of mechanical devices, reactor safety, mechanical constructions, transport systems, railway signalling devices, road traffic and protection at work in chemical plans. (DG) [de

Fusion Safety Program annual report, fiscal year 1985

International Nuclear Information System (INIS)

Holland, D.F.; Merrill, B.J.; Herring, J.S.; Piet, S.J.; Longhurst, G.R.

1987-02-01

The Fusion Safety Program (FSP) has supported magnetic fusion technology for seven years, and this is the seventh annual report issued by the FSP. Program focus is identification of the magnitude and distribution of radioactive inventories in fusion reactors, and research and analysis of postulated accident scenarios that could cause the release of a portion of these inventories. Research results are used to develop improved designs that can reduce the probability and magnitude of such releases and thus improve the overall safety of fusion reactors. During FY-1985, research activities continued and participation continued on the Ignition Systems Project (ISP). This report presents the significant results of EGandG Idaho, Inc., activities and those from outside contracts, and includes a list of publications produced during the year, and activities planned for FY-1986

Some safety considerations in laser-controlled thermonuclear reactors. Final report

International Nuclear Information System (INIS)

Botts, T.E.; Breton, D.; Chan, C.K.; Levy, S.I.; Sehnert, M.; Ullman, A.Z.

1978-07-01

A major objective of this study was to identify potential safety questions for laser controlled thermonuclear reactors. From the safety viewpoint, it does not appear that the actual laser controlled thermonuclear reactor conceptual designs present hazards very different than those of magnetically confined fusion reactors. Some aspects seem beneficial, such as small lithium inventories, and the absence of cryogenic devices, while other aspects are new, for example the explosion of pressure vessels and laser hazards themselves. Major aspects considered in this report include: (a) general safety considerations, (b) tritium inventories, (c) system behavior during loss of flow accidents, and (d) safety considerations of laser related penetrations

Technical reliability of geological disposal for high-level radioactive wastes in Japan. The second progress report. Part 3. Safety assessment for geological disposal systems

International Nuclear Information System (INIS)

1999-11-01

Based on the Advisory Committee Report on Nuclear Fuel Cycle Backend Policy submitted to the Japanese Government in 1997, JNC documents the progress of research and development program in the form of the second progress report (the first one published in 1992). It summarizes an evaluation of the technical reliability and safety of the geological disposal concept for high-level radioactive wastes (HLW) in Japan. The present document, the part 3 of the progress report, concerns safety assessment for geological disposal systems definitely introduced in part 1 and 2 of this series and consists of 9 chapters. Chapter I concerns the methodology for safety assessment while Chapter II deals with diversity and uncertainty about the scenario, the adequate model and the required data of the systems above. Chapter III summarizes the components of the geological disposal system. Chapter IV refers to the relationship between radioactive wastes and human life through groundwater, i.e. nuclide migration. In Chapter V is made a reference case which characterizes the geological environmental data using artificial barrier specifications. (Ohno. S.)

Mark I containment, short term program. Safety evaluation report

International Nuclear Information System (INIS)

1977-12-01

Presented is a Safety Evaluation Report (SER) prepared by the Office of Nuclear Reactor Regulation addressing the Short Term Program (STP) reassessment of the containment systems of operating Boiler Water Reactor (BWR) facilities with the Mark I containment system design. The information presented in this SER establishes the basis for the NRC staff's conclusion that licensed Mark I BWR facilities can continue to operate safely, without undue risk to the health and safety of the public, during an interim period of approximately two years while a methodical, comprehensive Long Term Program (LTP) is conducted. This SER also provides one of the basic foundations for the NRC staff review of the Mark I containment systems for facilities not yet licensed for operation

Preliminary Integrated Safety Analysis Status Report

International Nuclear Information System (INIS)

Gwyn, D.

2001-01-01

This report provides the status of the potential Monitored Geologic Repository (MGR) Integrated Safety Analysis (EA) by identifying the initial work scope scheduled for completion during the ISA development period, the schedules associated with the tasks identified, safety analysis issues encountered, and a summary of accomplishments during the reporting period. This status covers the period from October 1, 2000 through March 30, 2001

AEA Technology report on safety and the environment 1991/92

International Nuclear Information System (INIS)

1992-01-01

Safety management has been a key activity for AEA throughout our history. This will continue to be the case as our commercial strategy is developed to meet the needs of our customers. The provision of high quality service is central to AEA's objectives - and safety is an important part of our quality management system. This report describes AEA's safety arrangements and performance over the last year. The considerable resources which we have devoted to radiological protection - and increasingly to general industrial safety matters - show that we have a good record in managing the safety of our employees and of the public. We set objectives and targets consistent with our aim to have a demonstrably high level of safety performance. This report also highlights our commitment to protection of the environment. The careful attention which we have paid for many years to limiting the environmental effects of our radiological operations has been broadened to a more generally based environmental protection policy. AEA is pleased to be associated - both in regard to our own operations and as a supplier of consultancy services in environmental protection - with the increasing efforts made in this area by the business world. (UK)

Evaluating safety management system implementation

International Nuclear Information System (INIS)

Preuss, M.

2009-01-01

Canada is committed to not only maintaining, but also improving upon our record of having one of the safest aviation systems in the world. The development, implementation and maintenance of safety management systems is a significant step towards improving safety performance. Canada is considered a world leader in this area and we are fully engaged in implementation. By integrating risk management systems and business practices, the aviation industry stands to gain better safety performance with less regulatory intervention. These are important steps towards improving safety and enhancing the public's confidence in the safety of Canada's aviation system. (author)

Improving the regulation of safety at DOE nuclear facilities. Final report: Appendices

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-01

The report strongly recommends that, with the end of the Cold War, safety and health at DOE facilities should be regulated by outside agencies rather than by any regulatory scheme, DOE must maintain a strong internal safety management system; essentially all aspects of safety at DOE`s nuclear facilities should be externally regulated; and existing agencies rather than a new one should be responsible for external regulation.

Improving the regulation of safety at DOE nuclear facilities. Final report: Appendices

International Nuclear Information System (INIS)

1995-12-01

The report strongly recommends that, with the end of the Cold War, safety and health at DOE facilities should be regulated by outside agencies rather than by any regulatory scheme, DOE must maintain a strong internal safety management system; essentially all aspects of safety at DOE's nuclear facilities should be externally regulated; and existing agencies rather than a new one should be responsible for external regulation

Safety-evaluation report related to the final design of the Standard Nuclear Steam Supply Reference System - CESSAR System 80. Docket No. STN 50-470

International Nuclear Information System (INIS)

1983-03-01

Supplement No. 1 to the Safety Evaluation Report for the application filed by Combustion Engineering, Inc. for a Final Design Approval for the Combustion Engineering Standard Safety Analysis Report (STN 50-470) has been prepared by the Office of Nuclear Reactor Regulation of the Nuclear Regulatory Commission. The purpose of this supplement is to update the Safety Evaluation by providing: (1) the evaluation of additional information submitted by the applicant since the Safety Evaluation Report was issued, (2) the evaluation of the matters the staff had under review when the Safety Evaluation Report was issued, and (3) the response to comments made by the Advisory Committee on Reactor Safeguards

System Design and the Safety Basis

International Nuclear Information System (INIS)

Ellingson, Darrel

2008-01-01

The objective of this paper is to present the Bechtel Jacobs Company, LLC (BJC) Lessons Learned for system design as it relates to safety basis documentation. BJC has had to reconcile incomplete or outdated system description information with current facility safety basis for a number of situations in recent months. This paper has relevance in multiple topical areas including documented safety analysis, decontamination and decommissioning (D and D), safety basis (SB) implementation, safety and design integration, potential inadequacy of the safety analysis (PISA), technical safety requirements (TSR), and unreviewed safety questions. BJC learned that nuclear safety compliance relies on adequate and well documented system design information. A number of PIS As and TSR violations occurred due to inadequate or erroneous system design information. As a corrective action, BJC assessed the occurrences caused by systems design-safety basis interface problems. Safety systems reviewed included the Molten Salt Reactor Experiment (MSRE) Fluorination System, K-1065 fire alarm system, and the K-25 Radiation Criticality Accident Alarm System. The conclusion was that an inadequate knowledge of system design could result in continuous non-compliance issues relating to nuclear safety. This was especially true with older facilities that lacked current as-built drawings coupled with the loss of 'historical knowledge' as personnel retired or moved on in their careers. Walkdown of systems and the updating of drawings are imperative for nuclear safety compliance. System design integration with safety basis has relevance in the Department of Energy (DOE) complex. This paper presents the BJC Lessons Learned in this area. It will be of benefit to DOE contractors that manage and operate an aging population of nuclear facilities

Chemical Safety Vulnerability Working Group report. Volume 3

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 148 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. Volume 3 consists of eleven appendices containing the following: Field verification reports for Idaho National Engineering Lab., Rocky Flats Plant, Brookhaven National Lab., Los Alamos National Lab., and Sandia National Laboratories (NM); Mini-visits to small DOE sites; Working Group meeting, June 7--8, 1994; Commendable practices; Related chemical safety initiatives at DOE; Regulatory framework and industry initiatives related to chemical safety; and Chemical inventory data from field self-evaluation reports.

Chemical Safety Vulnerability Working Group report. Volume 3

International Nuclear Information System (INIS)

1994-09-01

The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 148 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. Volume 3 consists of eleven appendices containing the following: Field verification reports for Idaho National Engineering Lab., Rocky Flats Plant, Brookhaven National Lab., Los Alamos National Lab., and Sandia National Laboratories (NM); Mini-visits to small DOE sites; Working Group meeting, June 7--8, 1994; Commendable practices; Related chemical safety initiatives at DOE; Regulatory framework and industry initiatives related to chemical safety; and Chemical inventory data from field self-evaluation reports

Chemical Safety Vulnerability Working Group report. Volume 2

International Nuclear Information System (INIS)

1994-09-01

The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 148 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. Volume 2 consists of seven appendices containing the following: Tasking memorandums; Project plan for the CSV Review; Field verification guide for the CSV Review; Field verification report, Lawrence Livermore National Lab.; Field verification report, Oak Ridge Reservation; Field verification report, Savannah River Site; and the Field verification report, Hanford Site

Chemical Safety Vulnerability Working Group report. Volume 2

Energy Technology Data Exchange (ETDEWEB)

1994-09-01

The Chemical Safety Vulnerability (CSV) Working Group was established to identify adverse conditions involving hazardous chemicals at DOE facilities that might result in fires or explosions, release of hazardous chemicals to the environment, or exposure of workers or the public to chemicals. A CSV Review was conducted in 148 facilities at 29 sites. Eight generic vulnerabilities were documented related to: abandoned chemicals and chemical residuals; past chemical spills and ground releases; characterization of legacy chemicals and wastes; disposition of legacy chemicals; storage facilities and conditions; condition of facilities and support systems; unanalyzed and unaddressed hazards; and inventory control and tracking. Weaknesses in five programmatic areas were also identified related to: management commitment and planning; chemical safety management programs; aging facilities that continue to operate; nonoperating facilities awaiting deactivation; and resource allocations. Volume 2 consists of seven appendices containing the following: Tasking memorandums; Project plan for the CSV Review; Field verification guide for the CSV Review; Field verification report, Lawrence Livermore National Lab.; Field verification report, Oak Ridge Reservation; Field verification report, Savannah River Site; and the Field verification report, Hanford Site.

Annual safety research report, JFY 2010

International Nuclear Information System (INIS)

2011-09-01

In the safety infrastructure research working group report, 'the effective conducting of nuclear safety infrastructure research', published by METI in March 2010, the roles of regulatory agencies and JNES and their cooperation, and the research road map for nuclear safety regulation researches were summarized. As for the regulatory issues the governments or JNES considered necessary, JNES had compiled' safety research plan' in respective research areas necessary for solving the regulatory issues (safety research needs) and was conducting safety research to obtain the results, etc. Safety research areas, subjects and research projects were as follows: design review of nuclear power plant (4 subjects and each subject having several research projects totaled 19), control management of nuclear power plant (3 subjects and each subject having several research projects totaled 11), nuclear fuel cycle (2 subjects and each subject having several research projects totaled 5), nuclear fuel cycle backend (2 subjects and each subject having several research projects totaled 6), nuclear emergency preparedness and response (3 subjects and each subject having several research projects totaled 5) and bases of nuclear safety technology (3 subjects and each subject having several research projects totaled 7). In JFY 2010, JNES worked on the 53 research projects of 17 subjects in 6 areas as safety researches. This annual safety research report summarized respective achievements and stage of regulatory tools necessary for solving regulatory issues according to the safety research plan, JFY 2010 Edition as well as the situation of the reflection for the safety regulations. (T. Tanaka)

Safety Information System Guide

International Nuclear Information System (INIS)

Bullock, M.G.

1977-03-01

This Guide provides guidelines for the design and evaluation of a working safety information system. For the relatively few safety professionals who have already adopted computer-based programs, this Guide may aid them in the evaluation of their present system. To those who intend to develop an information system, it will, hopefully, inspire new thinking and encourage steps towards systems safety management. For the line manager who is working where the action is, this Guide may provide insight on the importance of accident facts as a tool for moving ideas up the communication ladder where they will be heard and acted upon; where what he has to say will influence beneficial changes among those who plan and control his operations. In the design of a safety information system, it is suggested that the safety manager make friends with a computer expert or someone on the management team who has some feeling for, and understanding of, the art of information storage and retrieval as a new and better means for communication

Annual report on reactor safety research projects sponsored by the Ministry of Economics and Technology of the Federal Republic of Germany. Reporting period 2007. Progress report

International Nuclear Information System (INIS)

2007-01-01

Within its competence for energy research the Federal Ministry of Economics and Technology (BMWi) sponsors research projects on the safety of nuclear power plants currently in operation. The objective of these projects is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order of the BMWi, continuously issues information on the status of such research projects by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, results achieved, next steps of the work etc. The individual reports are prepared in a standard form by the research organisations themselves as documentation of their progress in work. The progress reports are published by the Research Management Division of GRS. The reports as of the year 2000 are available in the Internet-based information system on results and data of reactor safety research (http://www.grs-fbw.de). The compilation of the reports is classified according to the classification system 'Joint Safety Research Index (JSRI)'. The reports are arranged in sequence of their project numbers. It has to be pointed out that the authors of the reports are responsible for the contents of this compilation. The BMWi does not take any responsibility for the correctness, exactness and completeness of the information nor for the observance of private claims of third parties. (orig.)

Identification of new unresolved safety issues relating to nuclear power plants - special report to Congress. Congressional report

International Nuclear Information System (INIS)

1981-03-01

As a result of NRC staff review and extended collegial consultations and investigations within the NRC, the Commission has designated four new Unresolved Safety Issues (USIs). This report describes the process used to evaluate the large number of concerns and recommendations which resulted from the major investigations of the Three Mile Island-2 accident as well as other events and investigations of the past year, and the report identifies the four new USIs selected as follows: (1) Shutdown decay heat removal requirements (Task A-45); (2) Seismic qualification of equipment in operating plants (Task A-46); (3) Safety implications of control systems (Task A-47); and (4) Hydrogen control measures and effects of hydrogen burns on safety equipment (Task A-48). Appendix A of the report presents an expanded discussion of each new USI including issue definition, a preliminary discussion of the action plan and a basis for continued plant operations and licensing. Appendix B of the report provides a brief discussion of each of the candidate safety issues not designated as an USI

Safety-related LWR research. Annual report 1993

International Nuclear Information System (INIS)

Hueper, R.

1994-06-01

The reactor safety R and D work of the Karlsruhe Nuclear Research Centre (KfK) has been part of the Nuclear Safety Research Project (PSF) since 1990. The present annual report 1993 summarizes the results on LWR safety. The research tasks are coordinated in agreement with internal and external working groups. The contributions to this report correspond to the status at the end of 1993. (orig./HP) [de

John M. Eisenberg Patient Safety Awards. System innovation: Veterans Health Administration National Center for Patient Safety.

Science.gov (United States)

Heget, Jeffrey R; Bagian, James P; Lee, Caryl Z; Gosbee, John W

2002-12-01

In 1998 the Veterans Health Administration (VHA) created the National Center for Patient Safety (NCPS) to lead the effort to reduce adverse events and close calls systemwide. NCPS's aim is to foster a culture of safety in the Department of Veterans Affairs (VA) by developing and providing patient safety programs and delivering standardized tools, methods, and initiatives to the 163 VA facilities. To create a system-oriented approach to patient safety, NCPS looked for models in fields such as aviation, nuclear power, human factors, and safety engineering. Core concepts included a non-punitive approach to patient safety activities that emphasizes systems-based learning, the active seeking out of close calls, which are viewed as opportunities for learning and investigation, and the use of interdisciplinary teams to investigate close calls and adverse events through a root cause analysis (RCA) process. Participation by VA facilities and networks was voluntary. NCPS has always aimed to develop a program that would be applicable both within the VA and beyond. NCPS's full patient safety program was tested and implemented throughout the VA system from November 1999 to August 2000. Program components included an RCA system for use by caregivers at the front line, a system for the aggregate review of RCA results, information systems software, alerts and advisories, and cognitive acids. Following program implementation, NCPS saw a 900-fold increase in reporting of close calls of high-priority events, reflecting the level of commitment to the program by VHA leaders and staff.

Architecture Level Safety Analyses for Safety-Critical Systems

Directory of Open Access Journals (Sweden)

K. S. Kushal

2017-01-01

Full Text Available The dependency of complex embedded Safety-Critical Systems across Avionics and Aerospace domains on their underlying software and hardware components has gradually increased with progression in time. Such application domain systems are developed based on a complex integrated architecture, which is modular in nature. Engineering practices assured with system safety standards to manage the failure, faulty, and unsafe operational conditions are very much necessary. System safety analyses involve the analysis of complex software architecture of the system, a major aspect in leading to fatal consequences in the behaviour of Safety-Critical Systems, and provide high reliability and dependability factors during their development. In this paper, we propose an architecture fault modeling and the safety analyses approach that will aid in identifying and eliminating the design flaws. The formal foundations of SAE Architecture Analysis & Design Language (AADL augmented with the Error Model Annex (EMV are discussed. The fault propagation, failure behaviour, and the composite behaviour of the design flaws/failures are considered for architecture safety analysis. The illustration of the proposed approach is validated by implementing the Speed Control Unit of Power-Boat Autopilot (PBA system. The Error Model Annex (EMV is guided with the pattern of consideration and inclusion of probable failure scenarios and propagation of fault conditions in the Speed Control Unit of Power-Boat Autopilot (PBA. This helps in validating the system architecture with the detection of the error event in the model and its impact in the operational environment. This also provides an insight of the certification impact that these exceptional conditions pose at various criticality levels and design assurance levels and its implications in verifying and validating the designs.

Annual report on occupational safety 1983

International Nuclear Information System (INIS)

1984-08-01

The 1983 Annual Report on occupational safety at BNFL is presented. Data for whole-body radiation doses and skin and extremity doses are given for BNFL employees together with 1982 data for comparison. Similarly, accidental deaths and major injuries are recorded. Finally information on the frequency of both nuclear and non-nuclear incidents reported to the Health and Safety Executive is given. (U.K.)

Space Nuclear Safety Program. Progress report, March 1984

International Nuclear Information System (INIS)

Zocher, R.W.; George, T.G.

1985-08-01

This technical monthly report covers studies related to the use of 238 PuO 2 in radioisotope power systems carried out for the Office of Special Nuclear Projects of the US Department of Energy by Los Alamos Laboratory. They are divided into: general-purpose heat source, lightweight radioisotope heater unit, and safety technology program. 43 figs., 2 tabs

Annual health, safety and environmental performance report for 1993

Energy Technology Data Exchange (ETDEWEB)

Gallapher, J D; Wright, M G

1994-05-01

This report summarizes the occupational health and safety and the environmental protection record of the operations of Atomic Energy of Canada Limited (AECL) during 1993. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes, and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices. (author). 14 figs.

Annual health, safety and environmental performance report for 1993

International Nuclear Information System (INIS)

Gallapher, J.D.; Wright, M.G.

1994-05-01

This report summarizes the occupational health and safety and the environmental protection record of the operations of Atomic Energy of Canada Limited (AECL) during 1993. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes, and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices. (author). 14 figs

Patient Drug Safety Reporting: Diabetes Patients' Perceptions of Drug Safety and How to Improve Reporting of Adverse Events and Product Complaints.

Science.gov (United States)

Patel, Puja; Spears, David; Eriksen, Betina Østergaard; Lollike, Karsten; Sacco, Michael

2018-03-01

Global health care manufacturer Novo Nordisk commissioned research regarding awareness of drug safety department activities and potential to increase patient feedback. Objectives were to examine patients' knowledge of pharmaceutical manufacturers' responsibilities and efforts regarding drug safety, their perceptions and experiences related to these efforts, and how these factors influence their thoughts and behaviors. Data were collected before and after respondents read a description of a drug safety department and its practices. We conducted quantitative survey research across 608 health care consumers receiving treatment for diabetes in the United States, Germany, United Kingdom, and Italy. This research validated initial, exploratory qualitative research (across 40 comparable consumers from the same countries) which served to guide design of the larger study. Before reading a drug safety department description, 55% of respondents were unaware these departments collect safety information on products and patients. After reading the description, 34% reported the department does more than they expected to ensure drug safety, and 56% reported "more confidence" in the industry as a whole. Further, 66% reported themselves more likely to report an adverse event or product complaint, and 60% reported that they were more likely to contact a drug safety department with questions. The most preferred communication methods were websites/online forums (39%), email (27%), and telephone (25%). Learning about drug safety departments elevates consumers' confidence in manufacturers' safety efforts and establishes potential for patients to engage in increased self-monitoring and reporting. Study results reveal potentially actionable insights for the industry across patient and physician programs and communications.

Fusion Reactor Safety Research program. Annual report, FY-80

International Nuclear Information System (INIS)

Crocker, J.G.; Cohen, S.

1981-06-01

The report is in three sections. Outside contracts includes a report of newly-started study at the General Atomic Company to consider safety implications of low-activation materials, portions of two papers from ongoing work at PNL and ANL, reports of the lithium spill work at HEDL, the LITFIRE code development at MIT, and risk assessment at MIT, all of which are an expansion of FY-79 outside contracts. EG and G Activities includes adaptations of four papers of ongoing work in transient code development, tritium system risk assessment, heat transfer and fluid flow analysis, and fusion safety data base. Program Plan Development includes the Executive Summary of the Plan, which was completed in FY-80, and is accompanied by a list of publications and a brief outline of proposed FY-81 activities to be based on the Program Plan

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2008-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

System and safety studies of accelerator driven transmutation systems

Energy Technology Data Exchange (ETDEWEB)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J. [Royal Inst. of Technology, Stockholm (Sweden). Dept. of Nuclear and Reactor Physics

2001-05-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the department has been focused on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache). Moreover, during the reporting period the EU-project 'IABAT', co-ordinated by the department has been finished and 4 other projects have been initiated in the frame of the 5th European Framework Programme. Most of the research topics reported in this paper are referred to appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details.

System and safety studies of accelerator driven transmutation systems

International Nuclear Information System (INIS)

Gudowski, W.; Wallenius, J.; Tucek, K.; Eriksson, Marcus; Carlsson, Johan; Seltborg, P.; Cetnar, J.

2001-05-01

The research on safety of Accelerator-Driven Transmutation Systems (ADS) at the department has been focused on: a) ADS core design and development of advanced nuclear fuel optimised for high transmutation rates and good safety features; b) analysis of ADS-dynamics c) computer code and nuclear data development relevant for simulation and optimization of ADS; d) participation in ADS experiments including 1 MW spallation target manufacturing, subcritical experiments MUSE (CEA-Cadarache). Moreover, during the reporting period the EU-project 'IABAT', co-ordinated by the department has been finished and 4 other projects have been initiated in the frame of the 5th European Framework Programme. Most of the research topics reported in this paper are referred to appendices, which have been published in the open literature. The topics, which are not yet published, are described here in more details

Reactor safety: the Nova computer system

International Nuclear Information System (INIS)

Eisgruber, H.; Stadelmann, W.

1991-01-01

After instances of maloperation, the causes of defects, the effectiveness of the measures taken to control the situation, and possibilities to avoid future recurrences need to be investigated above all before the plant is restarted. The most important aspect in all these efforts is to check the sequence in time, and the completeness, of the control measures initiated automatically. For this verification, a computer system is used instead of time-consuming manual analytical techniques, which produces the necessary information almost in real time. The results are available within minutes after completion of the measures initiated automatically. As all short-term safety functions are initiated by automatic systems, their consistent and comprehensive verification results in a clearly higher level of safety. The report covers the development of the computer system, and its implementation, in the Gundremmingen nuclear power station. Similar plans are being pursued in Biblis and Muelheim-Kaerlich. (orig.) [de

Design review report for modifications to RMCS safety class equipment

International Nuclear Information System (INIS)

Corbett, J.E.

1997-01-01

This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable

Design review report for modifications to RMCS safety class equipment

Energy Technology Data Exchange (ETDEWEB)

Corbett, J.E.

1997-05-30

This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable.

Safety report for Central Interim Storage facility for radioactive waste from small producers

International Nuclear Information System (INIS)

Zeleznik, N.; Mele, I.

2004-01-01

In 1999 the Agency for Radwaste Management took over the management of the Central Interim Storage (CIS) in Brinje, intended only for radioactive waste from industrial, medical and research applications. With the transfer of the responsibilities for the storage operation, ARAO, the new operator of the facility, received also the request from the Slovenian Nuclear Safety Administration for refurbishment and reconstruction of the storage and for preparation of the safety report for the storage with the operational conditions and limitations. In order to fulfill these requirements ARAO first thoroughly reviewed the existing documentation on the facility, the facility itself and the stored inventory. Based on the findings of this review ARAO prepared several basic documents for improvement of the current conditions in the storage facility. In October 2000 the Plan for refurbishment and modernization of the CIS was prepared, providing an integral approach towards remediation and refurbishment of the facility, optimization of the inventory arrangement and modernization of the storage and storing utilization. In October 2001 project documentation for renewal of electric installations, water supply and sewage system, ventilation system, the improvements of the fire protection and remediation of minor defects discovered in building were completed according to the Act on Construction. In July 2003 the safety report was prepared, based on the facility status after the completion of the reconstruction works. It takes into account all improvements and changes introduced by the refurbishment and reconstruction of the facility according to project documentation. Besides the basic characteristics of the location and its surrounding, it also gives the technical description of the facility together with proposed solutions for the renewal of electric installations, renovation of water supply and sewage system, refurbishment of the ventilation system, the improvement of fire

FOOD SAFETY CONTROL SYSTEM IN CHINA

Institute of Scientific and Technical Information of China (English)

Liu Wei-jun; Wei Yi-min; Han Jun; Luo Dan; Pan Jia-rong

2007-01-01

Most countries have expended much effort to develop food safety control systems to ensure safe food supplies within their borders. China, as one of the world's largest food producers and consumers,pays a lot of attention to food safety issues. In recent years, China has taken actions and implemented a series of plans in respect to food safety. Food safety control systems including regulatory, supervisory,and science and technology systems, have begun to be established in China. Using, as a base, an analysis of the current Chinese food safety control system as measured against international standards, this paper discusses the need for China to standardize its food safety control system. We then suggest some policies and measures to improve the Chinese food safety control system.

Complementary safety assessments - Report by the French Nuclear Safety Authority

International Nuclear Information System (INIS)

2011-12-01

As an immediate consequence of the Fukushima accident, the French Authority of Nuclear Safety (ASN) launched a campaign of on-site inspections and asked operators (mainly EDF, AREVA and CEA) to make complementary assessments of the safety of the nuclear facilities they manage. The approach defined by ASN for the complementary safety assessments (CSA) is to study the behaviour of nuclear facilities in severe accidents situations caused by an off-site natural hazard according to accident scenarios exceeding the current baseline safety requirements. This approach can be broken into 2 phases: first conformity to current design and secondly an approach to the beyond design-basis scenarios built around the principle of defence in depth. 38 inspections were performed on issues linked to the causes of the Fukushima crisis. It appears that some sites have to reinforce the robustness of the heat sink. The CSA confirmed that the processes put into place at EDF to detect non-conformities were satisfactory. The complementary safety assessments demonstrated that the current seismic margins on the EDF nuclear reactors are satisfactory. With regard to flooding, the complementary safety assessments show that the complete reassessment carried out following the flooding of the Le Blayais nuclear power plant in 1999 offers the installations a high level of protection against the risk of flooding. Concerning the loss of electrical power supplies and the loss of cooling systems, the analysis of EDF's CSA reports showed that certain heat sink and electrical power supply loss scenarios can, if nothing is done, lead to core melt in just a few hours in the most unfavourable circumstances. As for nuclear facilities that are not power or experimental reactors, some difficulties have appeared to implement the CSA approach that was initially devised for reactors. Generally speaking, ASN considers that the safety of nuclear facilities must be made more robust to improbable risks which are not

Making Residents Part of the Safety Culture: Improving Error Reporting and Reducing Harms.

Science.gov (United States)

Fox, Michael D; Bump, Gregory M; Butler, Gabriella A; Chen, Ling-Wan; Buchert, Andrew R

2017-01-30

Reporting medical errors is a focus of the patient safety movement. As frontline physicians, residents are optimally positioned to recognize errors and flaws in systems of care. Previous work highlights the difficulty of engaging residents in identification and/or reduction of medical errors and in integrating these trainees into their institutions' cultures of safety. The authors describe the implementation of a longitudinal, discipline-based, multifaceted curriculum to enhance the reporting of errors by pediatric residents at Children's Hospital of Pittsburgh of University of Pittsburgh Medical Center. The key elements of this curriculum included providing the necessary education to identify medical errors with an emphasis on systems-based causes, modeling of error reporting by faculty, and integrating error reporting and discussion into the residents' daily activities. The authors tracked monthly error reporting rates by residents and other health care professionals, in addition to serious harm event rates at the institution. The interventions resulted in significant increases in error reports filed by residents, from 3.6 to 37.8 per month over 4 years (P error reporting correlated with a decline in serious harm events, from 15.0 to 8.1 per month over 4 years (P = 0.01). Integrating patient safety into the everyday resident responsibilities encourages frequent reporting and discussion of medical errors and leads to improvements in patient care. Multiple simultaneous interventions are essential to making residents part of the safety culture of their training hospitals.

TIS General Safety Group Annual Report 2000

CERN Document Server

Weingarten, W

2001-01-01

This report summarises the main activities of the General Safety (GS) Group of the Technical Inspection and Safety Division (TIS) during the year 2000, and the results obtained. The different topics in which the Group is active are covered: general safety inspections and ergonomy, electrical, chemistry and gas safety, chemical pollution containment and control, industrial hygiene, the safety of civil engineering works and outside contractors, fire prevention and the safety aspects of the LHC experiments.

Research on the development of advanced system safety assessment procedures (1)

International Nuclear Information System (INIS)

Suzuki, Kazuhiko

2002-02-01

The past research reports in the area of safety engineering proposed the Computer-aided HAZOP system to be applied to Nuclear Reprocessing Facilities. Automated HAZOP system has great advantage compared with human analysts in terms of accuracy of the results, and time required to conduct HAZOP studies. This report surveys the literature on risk assessment and safety design based on the concept of independent protection layers (IPLs). Furthermore, to improve HAZOP System, counter measures information related to abnormal situation in plants are added to knowledge base in the system. As the result the HAZOP system can give appropriate measures information to protect accidents to uses. Such HAZOP system is applied to analyze the processes, where the ability of the proposed system is verified. (author)

Incident reporting: Its role in aviation safety and the acquisition of human error data

Science.gov (United States)

Reynard, W. D.

1983-01-01

The rationale for aviation incident reporting systems is presented and contrasted to some of the shortcomings of accident investigation procedures. The history of the United State's Aviation Safety Reporting System (ASRS) is outlined and the program's character explained. The planning elements that resulted in the ASRS program's voluntary, confidential, and non-punitive design are discussed. Immunity, from enforcement action and misuse of the volunteered data, is explained and evaluated. Report generation techniques and the ASRS data analysis process are described; in addition, examples of the ASRS program's output and accomplishments are detailed. Finally, the value of incident reporting for the acquisition of safety information, particularly human error data, is explored.

Safety evaluation of Tokai reprocessing plant (TRP). Report of safety evaluation of Tokai reprocessing plant

International Nuclear Information System (INIS)

Yamauchi, Takamichi; Maki, Akira; Nojiri, Ichiro

1999-02-01

The fire and explosion incident of the bituminization facility happened in March 1997 although JNC had taken enough care of the safety of TRP. JNC reflected on it and decided to evaluate the safety of TRP voluntarily. This evaluation has included five activities, that is, (1) confirmation of the structure and organization of TRP, (2) research of the data for operation, radiation and maintenance of TRP, (3) research of reflection of the accidents and troubles which have happened at the past, (4) evaluation on the prevention system, (5) evaluation on the mitigation system. We publish this report to contribute to inheritance of accumulated knowledge and techniques from generation to generation, and remind us of lesson from the fire and explosion incident of the bituminization. (author)

IRSN - Annual Report 2013. Financial Report 2013. Enhancing nuclear safety

International Nuclear Information System (INIS)

Schuler, Matthieu; Marchal, Valerie; Albert, Marc-Gerard; Aurelle, Jacques; Bigot, Marie-Pierre; Bruna, Giovanni; Charron, Sylvie; Clavelle, Stephanie; Cousinou, Patrick; Deschamps, Patrice; Delattre, Aleth; Demeillers, Didier; Dumas, Agnes; Franquard, Dominique; Laloi, Patrick; Lorthioir, Stephane; Monti, Pascale; Rollinger, Francois; Rouyer, Veronique; Rutschkovsky, Nathalie; Scott De Martinville, Edouard; Tharaud, Christine; Verpeaux, Jean-Luc; Jaunet, Camille; Hedouin, Jean-Christophe; Pascal-Heuze, Charlotte

2014-03-01

IRSN, a public entity with industrial and commercial activities, is placed under the joint authority of the Ministries of Defense, Environment, Industry, Research, and Health. It is the nation's public service expert in nuclear and radiation risks, and its activities cover all the related scientific and technical issues. Its areas of specialization include the environment and radiological emergency response, human radiation protection in both a medical and professional capacity, and in both normal and post-accident situations, the prevention of major accidents, nuclear reactor safety, as well as safety in nuclear plants and laboratories, transport and waste treatment, and nuclear defense and security expertise. IRSN interacts with all parties concerned by these risks (public authorities, in particular nuclear safety and security authorities, local authorities, companies, research organizations, stakeholders' associations, etc.) to contribute to public policy issues relating to nuclear safety, human and environmental protection against ionizing radiation, and the protection of nuclear materials, facilities, and transport against the risk of malicious acts. This document is the 2013 issue of IRSN's activity report. Content: 1 - Organization, key figures; 2 - Strategy: Progress and main activities in 2013, Transparency and communications policy, Promoting a safety and radiation protection culture; 3 - Activities: Safety (Safety of existing facilities, Studies and researches, About defense, Conducting assessments of future facilities); Nuclear security and non-proliferation (Nuclear security activities, International non-proliferation controls); Radiation protection - environment and human health (Environmental and population exposure, Radiation protection in the workplace, Effects of chronic exposure, Protection in health care); Emergency and post-accident situations efficiency; 4 - Efficiency: Health, safety, environmental, protection and quality, Human resources

Operating Experience from Events Reported to the IAEA Incident Reporting System for Research Reactors

International Nuclear Information System (INIS)

2015-03-01

Operating experience feedback is an effective mechanism in providing lessons learned from events and the associated corrective actions to prevent them, helping to improve safety at nuclear installations. The Incident Reporting System for Research Reactors (IRSRR), which is operated by the IAEA, is an important tool for international exchange of operating experience feedback for research reactors. The IRSRR reports contain information on events of safety significance with their root causes and lessons learned which help in reducing the occurrence of similar events at research reactors. To improve the effectiveness of the system, it is essential that national organizations demonstrate an appropriate interest for the timely reporting of events important to safety and share the information in the IRSRR database. At their biennial technical meetings, the IRSRR national coordinators recommended collecting the operating experience from the events reported to the IRSRR and disseminating it in an IAEA publication. This publication highlights the root causes, safety significance, lessons learned, corrective actions and the causal factors for the events reported to the IRSRR up to September 2014. The publication also contains relevant summary information on research reactor events from sources other than the IRSRR, operating experience feedback from the International Reporting System for Operating Experience considered relevant to research reactors, and a description of the elements of an operating experience programme as established by the IAEA safety standards. This publication will be of use to research reactor operating organizations, regulators and designers, and any other organizations or individuals involved in the safety of research reactors

Fusion safety program annual report fiscal year 1997

International Nuclear Information System (INIS)

Longhurst, G.R.; Anderl, R.A.; Cadwallader, L.C.

1998-01-01

This report summarizes the major activities of the Fusion Safety Program in FY 1997. The Idaho National Engineering and Environmental Laboratory (INEEL) is the designated lead laboratory, and Lockheed Martin Idaho Technologies Company is the prime contractor for this program. The Fusion Safety Program was initiated in FY 1979 to perform research and develop data needed to ensure safety in fusion facilities. Activities include experiments, analysis, code development and application, and other forms of research. These activities are conducted at the INEEL, different DOE laboratories, and other institutions. The technical areas covered in this report include chemical reactions and activation product release, tritium safety, risk assessment failure rate database development, and safety code development and application to fusion safety issues. Most of this work has been done in support of the International Thermonuclear Experimental Reactor (ITER) project. Work done for ITER this year has focused on developing the needed information for the Non-site Specific Safety Report (NSSR-2)

Fusion safety program annual report fiscal year 1997

Energy Technology Data Exchange (ETDEWEB)

Longhurst, G.R.; Anderl, R.A.; Cadwallader, L.C. [and others

1998-01-01

This report summarizes the major activities of the Fusion Safety Program in FY 1997. The Idaho National Engineering and Environmental Laboratory (INEEL) is the designated lead laboratory, and Lockheed Martin Idaho Technologies Company is the prime contractor for this program. The Fusion Safety Program was initiated in FY 1979 to perform research and develop data needed to ensure safety in fusion facilities. Activities include experiments, analysis, code development and application, and other forms of research. These activities are conducted at the INEEL, different DOE laboratories, and other institutions. The technical areas covered in this report include chemical reactions and activation product release, tritium safety, risk assessment failure rate database development, and safety code development and application to fusion safety issues. Most of this work has been done in support of the International Thermonuclear Experimental Reactor (ITER) project. Work done for ITER this year has focused on developing the needed information for the Non-site Specific Safety Report (NSSR-2).

76 FR 14592 - Safety Management System; Withdrawal

Science.gov (United States)

2011-03-17

...), Federal Aviation Administration, 800 Independence Avenue, SW., Washington, DC 20591; telephone (202) 494...). The FAA also chartered the Safety Management System Aviation Rulemaking Committee (ARC) (Order No..., including the ANPRM. On March 31, 2010, the ARC submitted its report to the FAA. As a result of the...

Proceedings of the Digital Systems Reliability and Nuclear Safety Workshop

Energy Technology Data Exchange (ETDEWEB)

Wallace, D. R.; Cuthill, B. B.; Ippolito, L. M. [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Beltracchi, L. [Nuclear Regulatory Commission, Washington, DC (United States) ed.

1994-03-01

The United States Nuclear Regulatory Commission (NRC), in cooperation with the National Institute of Standards and Technology conducted the.Digital Systems Reliability and Nuclear Safety Workshop on September 13--14, 1993, in Rockville, Maryland. The workshop provided a forum for the exchange of information among experts within the nuclear industry, experts from other industries, regulators and academia. The information presented at this workshop provided in-depth exposure of the NRC staff and the nuclear industry to digital systems design safety issues and also provided feedback to the NRC from outside experts regarding identified safety issues, proposed regulatory positions, and intended research associated with the use of digital systems in nuclear power plants. Technical presentations provided insights on areas where current software engineering practices may be inadequate for safety-critical systems, on potential solutions for development issues, and on methods for reducing risk in safety-critical systems. This report contains an analysis of results of the workshop, the papers presented panel presentations, and summaries of, discussions at this workshop. The individual papers have been cataloged separately.

Fusion Safety Program Annual Report, Fiscal Year 1996

International Nuclear Information System (INIS)

Longhurst, G.R.; Anderl, R.A.; Cadwallader, L.C.

1996-12-01

This report summarizes the major activities of the Fusion Safety Program in FY 1996. The Idaho National Engineering Laboratory (INEL) is the designated lead laboratory, and Lockheed Martin Idaho Technologies Company is the prime contractor for this program. The Fusion Safety Program was initiated in 1979. The objective is to perform research and develop data needed to ensure safety in fusion facilities. Activities include experiments, analysis, code development and application, and other forms of research. These activities are conducted at the INEL, at other DOE laboratories, and at other institutions. Among the technical areas covered in this report are tritium safety, chemical reactions and activation product release, risk assessment failure rate database development, and safety code development and application to fusion safety issues. Most of this work has been done in support of the International Thermonuclear Experimental Reactor (ITER). Work done for ITER this year has focused on developing the needed information for the Non- Site- Specific Safety Report (NSSR-1). A final area of activity described is development of the new DOE Technical Standards for Safety of Magnetic Fusion Facilities

Current status of safety analysis report for ANPP

International Nuclear Information System (INIS)

Amirjanyan, A.

1999-01-01

Current situation concerning Armenian NPP safety analysis report is considered within the frame of accepted safety practice. Licensing procedure is being developed. Technical support group was established in the Armenian Nuclear Regulatory Authority (ANRA). The task of the group is to study modern methods of NPP in depth safety analysis for technical assistance for the ANRA, and perform independent safety assessments. ANRA will be obliged to demand assistance from various foreign organisations for preparation of different parts of the Safety Analysis Report like determination though certain parts can be prepared in Armenia

Lessons learned - development of the tritium facilities 5480.23 safety analysis report and technical safety requirements

International Nuclear Information System (INIS)

Cappucci, A.J. Jr.; Bowman, M.E.; Goff, L.

1997-01-01

A review was performed which identified open-quotes Lessons Learnedclose quotes from the development of the 5480.23 Tritium Safety Analysis Report (SAR) and the Technical Safety Requirements (TSR) for the Tritium Facilities (TF). The open-quotes Lessons Learnedclose quotes were based on an evaluation of the use of the SRS procedures, processes, and work practices which contributed to the success or lack thereof. This review also identified recommendations and suggestions for improving the development of SARs and TSRs at SRS. The 5480.23 SAR describes the site for the TF, the various process systems in the process buildings, a complete hazards and accident analysis of the most significant hazards affecting the nearby offsite population, and the selection of safety systems, structures, and components to protect both the public and site workers. It also provides descriptions of important programs and processes which add defense in depth to public and worker protection