Methodology for safety optimization of highway cross-sections for horizontal curves with restricted sight distance.

Science.gov (United States)

Ibrahim, Shewkar E; Sayed, Tarek; Ismail, Karim

2012-11-01

Several earlier studies have noted the shortcomings with existing geometric design guides which provide deterministic standards. In these standards the safety margin of the design output is generally unknown and there is little knowledge of the safety implications of deviating from the standards. To mitigate these shortcomings, probabilistic geometric design has been advocated where reliability analysis can be used to account for the uncertainty in the design parameters and to provide a mechanism for risk measurement to evaluate the safety impact of deviations from design standards. This paper applies reliability analysis for optimizing the safety of highway cross-sections. The paper presents an original methodology to select a suitable combination of cross-section elements with restricted sight distance to result in reduced collisions and consistent risk levels. The purpose of this optimization method is to provide designers with a proactive approach to the design of cross-section elements in order to (i) minimize the risk associated with restricted sight distance, (ii) balance the risk across the two carriageways of the highway, and (iii) reduce the expected collision frequency. A case study involving nine cross-sections that are parts of two major highway developments in British Columbia, Canada, was presented. The results showed that an additional reduction in collisions can be realized by incorporating the reliability component, P(nc) (denoting the probability of non-compliance), in the optimization process. The proposed approach results in reduced and consistent risk levels for both travel directions in addition to further collision reductions. Copyright © 2012 Elsevier Ltd. All rights reserved.

Student and Faculty Issues in Distance Education.

Science.gov (United States)

Fender, David L.

Occupational safety and health faculty and occupational safety and health professionals (i.e., the potential audience for graduate level distance education programs) were surveyed to determine the considerations for a distance education-based graduate occupational safety and health program. Findings are reported related to the demand for distance…

7 CFR 1427.170 - Quantity for loan.

Science.gov (United States)

2010-01-01

... to the preservation or safety of the loan collateral. Loans may be made on a lower percentage basis... 7 Agriculture 10 2010-01-01 2010-01-01 false Quantity for loan. 1427.170 Section 1427.170... OF AGRICULTURE LOANS, PURCHASES, AND OTHER OPERATIONS COTTON Recourse Seed Cotton Loans § 1427.170...

Safety engineering experiments of explosives

Energy Technology Data Exchange (ETDEWEB)

Ishikawa, Noboru

1987-07-24

The outline of large scale experiments carried out every year since 1969 to obtain fundamental data and then establish the safety engineering standards concerning the manufacturing, storage and transportation, etc. of all explosives was described. Because it becomes recently difficult to ensure the safety distance in powder magazines and powder plants, the sandwich structure with sand is thought to be suitable as the neighboring barrier walls. The special vertical structure for embankments to provide against a emergency explosion is effective to absorb the blast. Explosion behaviors such as initiating sensitivity, detonation, sympathetic detonation, and shock occurence of the ANFO explosives in place of dynamite and the slurry explosives were studied. The safety engineering standards for the manufacturing and application of explosives were studied to establish because accidents by tabacco fire are not still distinguished. Much data concerning early stage fire fighting, a large quantity of flooding and shock occurence from a assumption of ignition during machining in the propellants manufacturing plant, could be obtained. Basic studies were made to prevent pollution in blasting sites. Collected data are utilized for the safety administration after sufficient discussion. (4 figs, 2 tabs, 3 photos, 17 refs)

Perencanaan Site Layout Facilities Berdasarkan Traveling Distance Dan Safety Index Pada Proyek Pembangunan Hotel The Alimar Surabaya

Directory of Open Access Journals (Sweden)

Angga Sukma Wijaya

2017-01-01

Full Text Available Proyek pembangunan hotel The Alimar Surabaya dengan 7 lantai , mempunyai luas tanah sebesar 900 m2 dengan KDB  650 m2 KLB 4550 m2. Permasalahan yang terjadi adalah bangunan tersebut mempunyai lahan yang tidak terlalu luas dan  berhimpitan langsung dengan rumah warga. Ruang gerak yang sempit akan sulit untuk menentukan penempatan site facilities. Dengan perencanaan site layout facilities yang dapat menghemat pemakaian ruang bangun. Semakin besar area yang digunakan dalam penempatan site facilities maka perjalanan antar fasilitas juga semakin banyak memakan waktu. Pembuatan alternatif site layout perlu dilakukan agar memperoleh site facilities yang optimal. Pada penelitian ini dilakukan perencanaan site layout facilities dengan traveling distance dan safety index  atau bisa disebut multi objectives function sebagai acuannya. Perencanaan site layout tersebut pada dasarnya dibagi dua tahap yaitu pada saat pekerjaan sub structure dan pekerjaan upper structure. Dari kedua tahap pekerjaan tersebut dapat menggunakan metode equal maupun unequal site layout. Pada perencanaan fasilitas juga diperhitungkan kebutuhan luas dan fasilitas material pada stock yard. Setelah melakukan iterasi dan membuat skenario-skenario bentuk site layout yang berbeda-beda kemudian terpilih salah satu yang mempunyai nilai multi objectives function paling minimum. Kemudian dengan menggunakan grafik pareto optima maka grafik tersebut mampu menunjukkan titik-titik objectives function yang paling minimum. Hasil yang di dapatkan adalah pada saat pekerjaan Sub Structure, site layout yang paling optimal adalah pada alternatif 665 yang mempunyai travelling distance dan safety index terendah dengan nilai TD sebesar 13246,18 m atau mengalami penurunan sebesar 3,30% dan nilai SI sebesar 1048 atau mengalami penurunan sebesar 5,76% dari kondisi perencanaan awal. Sedangkan Pada saat pekerjaan Upper Structure, site layout yang paling optimal adalah pada alternatif 122 yang mempunyai

Australia's tyranny of distance in oil spill response

International Nuclear Information System (INIS)

Lipscombe, Ray

2000-01-01

In view of the quantity of oil spilled, smaller spills generally receive less attention than headline grabbing incidents such as the 'Amoco Cadiz', 'Exxon Valdez', 'Braer' and 'Sea Empress'. The latter incidents involve the loss of significant quantities of oil, the establishment of relatively complex spill response management structures and the involvement of significant numbers of personnel and equipment. As such, large spills from tankers have the potential to create problem areas, for example in establishing and maintaining effective communications, logistics and resource management systems. In general terms spill response personnel are well aware that large spills come complete with significant operational and administrative problems, however what may not be so well recognised is that smaller spills also have the potential to present response personnel with their own unique problems. One of the major problems to be overcome when responding to spills in Australia is the 'tyranny of distance'. In quite a few responses, Australian oil spill response managers have had to move personnel and equipment thousands of kilometres to provide an effective outcome. This paper outlines a range of problems that have been encountered by Australian personnel over the years. These include health and safety, communications, logistics and equipment issues. For the purpose of this paper a 'smaller' spill has been defined as one involving a discharge of less than 1000 tonnes of oil. (Author)

Terminology report respect distance. The Use of the term respect distance in Posiva and SKB

International Nuclear Information System (INIS)

Lampinen, H.

2007-09-01

The term respect distance is used in some key publications of the Finnish Nuclear Waste Management Company, Posiva, and the Swedish Nuclear Waste Management Company, SKB (Svensk Kaernbrenslehantering). Posiva and SKB researchers use the same terms in their reports, and it is acknowledged that the terms used by both companies are not used in the same way, though the differences are often subtle. This report is a literature study of the term 'respect distance' and the terms immediately associated to it. Vital terms related to the respect distance and issues concerning the use of scale concepts in Posiva and SKB are gathered in the end of report. Posiva's respect distances consider the seismic, hydrological and mechanical properties of the deterministic deformation zones as important issues that constitute a risk for longterm safety. These requirements for respect distances are an interpretation of STUK's YVL 8.4 Guide. At present, Posiva's criteria regarding respect distances follow the instructions given in the Host Rock Classification system (HRC), whereas the size of a deformation zone to which respect distances are applied vary from the regional to local major and minor. This and other criteria that are given for respect distances may, however, change in the near future as Posiva's Rock Suitability Criteria (RSC) programme proceeds. SKB's considerations of respect distances acknowledge that the hydraulic and mechanical aspects of a deformation zone have an effect on the respect distance. However, the seismic risk is considered to overshadow the other effects on a regional scale. The respect distance defined for a deformation zone is coupled with the size of a fracture where secondary slip could occur. In the safety assessment it is assumed that this fracture cuts a deposition hole location. In SKB the respect distance is determined for regional and local major deformation zones. The trace length of such a zone is defined as being ≥ 3 km. For deformation zones

Management of Small Quantity of Nuclear Material at Locations Outside Facilities in Korea

Energy Technology Data Exchange (ETDEWEB)

Park, Seung Sik; Kim, Ki Hyun [KAERI, Daejeon (Korea, Republic of)

2016-05-15

Small quantity of nuclear material (SQNM) is prescribed to be less than specified minimum quantities of nuclear material in a facility. SQNM is used at the locations called locations outside facilities (LOFs). LOFs are used to control the locations and installations that store nuclear materials under one effective Kg, respectively. Holders of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or neither report them to the System of Accounting for and Control of nuclear material (SSAC) under specified quantities according to the Atomic Safety Law. Well defined safeguards law is fundamental to the effective control of nuclear material, facilities and nuclear related activities. In the current nuclear safety legislation, there are some exceptive clauses. Users of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or not report them to the national authority below specified amount.

Management of Small Quantity of Nuclear Material at Locations Outside Facilities in Korea

International Nuclear Information System (INIS)

Park, Seung Sik; Kim, Ki Hyun

2016-01-01

Small quantity of nuclear material (SQNM) is prescribed to be less than specified minimum quantities of nuclear material in a facility. SQNM is used at the locations called locations outside facilities (LOFs). LOFs are used to control the locations and installations that store nuclear materials under one effective Kg, respectively. Holders of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or neither report them to the System of Accounting for and Control of nuclear material (SSAC) under specified quantities according to the Atomic Safety Law. Well defined safeguards law is fundamental to the effective control of nuclear material, facilities and nuclear related activities. In the current nuclear safety legislation, there are some exceptive clauses. Users of SQNM don't need to require a license for use or possession of Uranium or Thorium exclusively for non-nuclear activities, or not report them to the national authority below specified amount

Quantity Distance for the Kennedy Space Center Vehicle Assembly Building for Solid Propellant Fueled Launchers

Science.gov (United States)

Stover, Steven; Diebler, Corey; Frazier, Wayne

2006-01-01

The NASA KSC VAB was built to process Apollo launchers in the 1960's, and later adapted to process Space Shuttles. The VAB has served as a place to assemble solid rocket motors (5RM) and mate them to the vehicle's external fuel tank and Orbiter before rollout to the launch pad. As Space Shuttle is phased out, and new launchers are developed, the VAB may again be adapted to process these new launchers. Current launch vehicle designs call for continued and perhaps increased use of SRM segments; hence, the safe separation distances are in the process of being re-calculated. Cognizant NASA personnel and the solid rocket contractor have revisited the above VAB QD considerations and suggest that it may be revised to allow a greater number of motor segments within the VAB. This revision assumes that an inadvertent ignition of one SRM stack in its High Bay need not cause immediate and complete involvement of boosters that are part of a vehicle in adjacent High Bay. To support this assumption, NASA and contractor personnel proposed a strawman test approach for obtaining subscale data that may be used to develop phenomenological insight and to develop confidence in an analysis model for later use on full-scale situations. A team of subject matter experts in safety and siting of propellants and explosives were assembled to review the subscale test approach and provide options to NASA. Upon deliberations regarding the various options, the team arrived at some preliminary recommendations for NASA.

Absorption distances in the dynamical theory of electron diffraction

International Nuclear Information System (INIS)

Kamiya, Yoshihiko; Goto, Toshiaki.

1982-01-01

The contrast effect of the electron microscopic image at crystal defects is characterized by two parameters; extincion distance and absorption distance. Both quantities are orginally defined for the elastic scattering. Since the inelastic scattering contributes to the electron microscopic image, parameters used for the interpretation of the images are not the same as those for the elastic scattering. It is shown that the difference of absorption distance beteen the theoretical estimation and that used for interpretation is due to the contrst effect of the small angle inelastic scattering. (author)

Thin-layer boilover in diesel-oil fires: Determining the increase of thermal hazards and safety distances

International Nuclear Information System (INIS)

Ferrero, Fabio; Munoz, Miguel; Arnaldos, Josep

2007-01-01

A study of the effects of thin-layer boilover on large hydrocarbon fires was carried out. In the experiments, diesel-oil was burned in pools with diameters ranging from 1.5 to 6 m. Previous models used to predict emissive power during the stationary state were analysed and successively modified in order to accurately predict thermal hazard during the water ebullition phase. It was discovered that the increase in emissive power during thin-layer boilover is greater when the pool diameter is smaller. Furthermore, the required increases in safety distances in the case of accidents involving this dangerous phenomenon are provided

Does distance e-learning work? A comparison between distance and face-to-face learners using e-learning materials

Directory of Open Access Journals (Sweden)

Sara de Freitas

2003-12-01

Full Text Available This study compares continual assessment data, intake numbers, retention numbers and final examination grades of a mixed cohort of face-to-face and distance learners against similar data from previous years where e-learning materials were not used in order to test whether e-learning materials can support the same quality and quantity of teaching and learning for both face-to-face and distance learners. The results for this cohort of learners demonstrate that: (i distance e-learners score as well and sometimes better than face-to-face learners; (ii face-to-face student numbers have increased; (iii overall, student retention and student attendance have been maintained; (iv final examination results have been maintained or in some cases improved; (v lecturer workload was high, but not unmanageable, and it is clear how manageability can be improved.

Strongly intensive quantities

International Nuclear Information System (INIS)

Gorenstein, M. I.; Gazdzicki, M.

2011-01-01

Analysis of fluctuations of hadron production properties in collisions of relativistic particles profits from use of measurable intensive quantities which are independent of system size variations. The first family of such quantities was proposed in 1992; another is introduced in this paper. Furthermore we present a proof of independence of volume fluctuations for quantities from both families within the framework of the grand canonical ensemble. These quantities are referred to as strongly intensive ones. Influence of conservation laws and resonance decays is also discussed.

GOSH! : an open and distance learning programme which helps in Gearing up to the Occupational Safety and Health Systems of the European Union

NARCIS (Netherlands)

Robertson, S.A.; Piek, W.S.M.; Kwantes, J.H.; Meeuwsen, J.M.; Man. M. de

1999-01-01

The GOSH! open and distance learning programme on the topic of occupational safety and health (OSH) was organized as part of the European Studies Programme. Prevention of damage to workers' health is an important issue in EU-policy. Apart from the individual human trauma, the socio-economic costs of

Mevatron-74 10MeV photon beam: a study of dosimetric quantities

International Nuclear Information System (INIS)

Souza, C.N. de

1986-01-01

The Mevatron-74 linear accelerator dosimetric quantities were studied. In water and polystyrene measurements with an ionization chamber were done for following physical parameters: maximum dose depth and surface dose, field size dependence, central axis percentage depth dose, beam flatness and simmetry, and also verification the inverse square law for the distances normally used in therapy. Isodose curves were generated by the decrement lines method. (Author) [pt

A study on fire spreading model for the safety distance between the neighborhood occupancies and historical buildings in Taiwan

Science.gov (United States)

Chen, C. H.; Chien, S. W.; Ho, M. C.

2015-08-01

Cultural heritages and historical buildings are vulnerable against severe threats from fire. Since the 1970s, ten fire-spread events involving historic buildings have occurred in Taiwan, affecting a total of 132 nearby buildings. Developed under the influence of traditional Taiwanese culture, historic buildings in Taiwan are often built using non-fire resistant brick-wood structure and located in proximity to residential occupancies. Fire outbreak in these types of neighborhood will lead to severe damage of antiquities, leaving only unrecoverable historical imagery. This study is aimed to investigate the minimal safety distance required between a historical building and its surroundings in order to reduce the risk of external fire. This study is based on literature analysis and the fire spread model using a Fire Dynamics Simulator. The selected target is Jingmei Temple in Taipei City. This study explored local geography to identify patterns behind historical buildings distribution. In the past, risk reduction engineering for cultural heritages and historical buildings focused mainly on fire equipment and the available personnel with emergency response ability, and little attention was given to external fire risks and the affected damage. Through discussions on the required safety distance, this research provides guidelines for the following items: management of neighborhoods with historical buildings and consultation between the protection of cultural heritages and disaster prevention, reducing the frequency and extent of fire damages, and preserving cultural resource.

Australia's tyranny of distance in oil spill response

Energy Technology Data Exchange (ETDEWEB)

Lipscombe, Ray [Australian Maritime Safety Authority, Environment Protection Group, Canberra, ACT (Australia)

2000-08-01

In view of the quantity of oil spilled, smaller spills generally receive less attention than headline grabbing incidents such as the 'Amoco Cadiz', 'Exxon Valdez', 'Braer' and 'Sea Empress'. The latter incidents involve the loss of significant quantities of oil, the establishment of relatively complex spill response management structures and the involvement of significant numbers of personnel and equipment. As such, large spills from tankers have the potential to create problem areas, for example in establishing and maintaining effective communications, logistics and resource management systems. In general terms spill response personnel are well aware that large spills come complete with significant operational and administrative problems, however what may not be so well recognised is that smaller spills also have the potential to present response personnel with their own unique problems. One of the major problems to be overcome when responding to spills in Australia is the 'tyranny of distance'. In quite a few responses, Australian oil spill response managers have had to move personnel and equipment thousands of kilometres to provide an effective outcome. This paper outlines a range of problems that have been encountered by Australian personnel over the years. These include health and safety, communications, logistics and equipment issues. For the purpose of this paper a 'smaller' spill has been defined as one involving a discharge of less than 1000 tonnes of oil. (Author)

Quantity processing in deaf and hard of hearing children: evidence from symbolic and nonsymbolic comparison tasks.

Science.gov (United States)

Rodríguez-Santos, José Miguel; Calleja, Marina; García-Orza, Javier; Iza, Mauricio; Damas, Jesús

2014-01-01

Deaf children usually achieve lower scores on numerical tasks than normally hearing peers. Explanations for mathematical disabilities in hearing children are based on quantity representation deficits (Geary, 1994) or on deficits in accessing these representations (Rousselle & Noël, 2008). The present study aimed to verify, by means of symbolic (Arabic digits) and nonsymbolic (dot constellations and hands) magnitude comparison tasks, whether deaf children show deficits in representations or in accessing numerical representations. The study participants were 10 prelocutive deaf children and 10 normally hearing children. Numerical distance and magnitude were manipulated. Response time (RT) analysis showed similar magnitude and distance effects in both groups on the 3 tasks. However, slower RTs were observed among the deaf participants on the symbolic task alone. These results suggest that although both groups' quantity representations were similar, the deaf group experienced a delay in accessing representations from symbolic codes.

Unpacking a time interval lengthens its perceived temporal distance

Directory of Open Access Journals (Sweden)

Yang eLiu

2014-11-01

Full Text Available In quantity estimation, people often perceive that the whole is less than the sum of its parts. The current study investigated such an unpacking effect in temporal distance judgment. Our results showed that participants in the unpacked condition judged a given time interval longer than those in the packed condition, even the time interval was kept constant between the two conditions. Furthermore, this unpacking effect persists regardless of the unpacking ways we employed. Results suggest that unpacking a time interval may be a good strategy for lengthening its perceived temporal distance.

Metrics for measuring distances in configuration spaces

International Nuclear Information System (INIS)

Sadeghi, Ali; Ghasemi, S. Alireza; Schaefer, Bastian; Mohr, Stephan; Goedecker, Stefan; Lill, Markus A.

2013-01-01

In order to characterize molecular structures we introduce configurational fingerprint vectors which are counterparts of quantities used experimentally to identify structures. The Euclidean distance between the configurational fingerprint vectors satisfies the properties of a metric and can therefore safely be used to measure dissimilarities between configurations in the high dimensional configuration space. In particular we show that these metrics are a perfect and computationally cheap replacement for the root-mean-square distance (RMSD) when one has to decide whether two noise contaminated configurations are identical or not. We introduce a Monte Carlo approach to obtain the global minimum of the RMSD between configurations, which is obtained from a global minimization over all translations, rotations, and permutations of atomic indices

Review on evolvement of systems of ionizing radiation quantities and units

International Nuclear Information System (INIS)

Zheng Junzheng; Zeng Zhi

2009-01-01

To scientifically and practically measure the ionizing radiation in unison is an indispensable prerequisite and foundation for the extensive uses of nuclear science and technology, development of radiological protection and safety standards, as well as prevention and treatment of ionizing radiation hazards. Concerning about the quantities and units of ionizing radiation as well as their corresponding measurement and application methods, relevant international organizations and all countries in the world generally adopt the systems proposed by the International Commission on Radiation Units and Measurements (ICRU) which is a well recognized and authoritative academic organization.In the paper,the major evolutions of the systems for ionizing radiation quantities and units in the past decades are summarized. (authors)

3D GIS BASED EVALUATION OF THE AVAILABLE SIGHT DISTANCE TO ASSESS SAFETY OF URBAN ROADS

Directory of Open Access Journals (Sweden)

M. Bassani

2015-08-01

Full Text Available The available sight distance (ASD in front of the driver to detect possible conflicts with unexpected obstacles is fundamental for traffic safety. In the last 20 years, road design software (RDS has been continuously updated with dedicated modules to estimate ASD, thus assessing the quality of project from a safety point of view. Unfortunately, the evaluation of ASD still represents an issue in the case of existing road, and the object of discussion in the research community. To avoid problems related to the limitation associated with the use of digital terrain models typically employed in RDS, the Geographic Information Systems (GIS software can use digital surface models (DSM which are more flexible in the modelling of sight obstruction due to vegetation, street furniture, and vertical surfaces largely diffused in urbanized areas. The paper deals with the evaluation of GIS in the estimation of ASD in a typical urban road where the density of sight obstruction along the roadside is relatively high. The work explores the case study of a collector road in the city of Turin (Italy. Results confirm the potentiality of GIS software in capturing the complex morphology of the urban environment, thus confirming that GIS could become an important analysis tool for road engineers in the field of road safety. The investigation here described is part of the Pro-VISION Project (funded in 2014 by the Regione Piemonte, Italy.

Dangerous quantities of radioactive material (D-values). Emergency preparedness and response. Publication date: August 2006

International Nuclear Information System (INIS)

2006-08-01

Radioactive material is widely used in industry, medicine, education and agriculture. In addition, it occurs naturally. The health risk posed by these materials vary widely depending on many factors, the most important of which are the amount of the material involved and its physical and chemical form. Therefore, there is a need to identify the quantity and type of radioactive material for which emergency preparedness and other arrangements (e.g. security) are warrant due to the health risk they pose. The aim of this publication is to provide practical guidance for Member States on that quantity of radioactive material that may be considered dangerous. A dangerous quantity is that, which if uncontrolled, could be involved in a reasonable scenario resulting in the death of an exposed individual or a permanent injury, which decreases that person's quality of life. This publication is published as part of the IAEA Emergency Preparedness and Response Series. It supports several publications including: the IAEA Safety Requirements 'Preparedness and Response for a Nuclear or Radiological Emergency', IAEA Safety Standards Series No. GS-R-2. IAEA, Vienna (2002); IAEA Safety Guide 'Categorization of Radioactive Sources', IAEA Safety Standards Series No RS-G-1.9, IAEA, Vienna (2005) and IAEA Safety Guide 'Arrangements for Preparedness for a Nuclear or Radiological Emergency' IAEA Safety Standards Series No. GS-G-2.1, IAEA, Vienna (2006). The procedures and data in this publication have been prepared with due attention to accuracy. However, as part of the review process, they undergo ongoing quality assurance checks. Comments are welcome and, following a period that will allow for a more extensive review, the IAEA may revise this publication as part of the process of continuous improvement. The publication uses a number of exposure scenarios, risk models and dosimetric data, which could be used during the response to nuclear or radiological emergency or other purposes

Quality Assurance Systems in Open and Distance Learning: A ...

African Journals Online (AJOL)

The article has articulated as to why providers, consumers and accreditation agencies are at all levels interested in quality assurance. For the case of Tanzania ... In the same vein quality education for open and distance education has to remain top in the agenda so as to balance both quantity and quality. Lastly the article ...

Hydrogen safety

International Nuclear Information System (INIS)

Frazier, W.R.

1991-01-01

The NASA experience with hydrogen began in the 1950s when the National Advisory Committee on Aeronautics (NACA) research on rocket fuels was inherited by the newly formed National Aeronautics and Space Administration (NASA). Initial emphasis on the use of hydrogen as a fuel for high-altitude probes, satellites, and aircraft limited the available data on hydrogen hazards to small quantities of hydrogen. NASA began to use hydrogen as the principal liquid propellant for launch vehicles and quickly determined the need for hydrogen safety documentation to support design and operational requirements. The resulting NASA approach to hydrogen safety requires a joint effort by design and safety engineering to address hydrogen hazards and develop procedures for safe operation of equipment and facilities. NASA also determined the need for rigorous training and certification programs for personnel involved with hydrogen use. NASA's current use of hydrogen is mainly for large heavy-lift vehicle propulsion, which necessitates storage of large quantities for fueling space shots and for testing. Future use will involve new applications such as thermal imaging

16 CFR 500.25 - Net quantity, average quantity, permitted variations.

Science.gov (United States)

2010-01-01

... good distribution practice and which unavoidably result in change of weight or mass or measure. (c... good packaging practice: Provided, that such variations shall not be permitted to such extent that the... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Net quantity, average quantity, permitted...

Radiation quantities and units

International Nuclear Information System (INIS)

2013-01-01

This fifth chapter presents the conceptual evolution, the definition procedures, the radiological quantities themselves, the relation between them, the new operational quantities and the new quantities defined in the ICRP 60 that replaced ICRP 26 and was included in the CNEN-NN-3.01 standard of 2011

A Method for Improving Galactic Cepheid Reddenings and Distances

Energy Technology Data Exchange (ETDEWEB)

Madore, Barry F. [The Observatories Carnegie Institution for Science 813 Santa Barbara St., Pasadena, CA 91101 (United States); Freedman, Wendy L.; Moak, Sandy, E-mail: barry.f.madore@gmail.com, E-mail: sandymoak@gmail.com, E-mail: wfreedman@uchicago.edu [Dept. of Astronomy and Astrophysics, University of Chicago, Chicago, IL (United States)

2017-06-10

We present a new photometric method by which improved high-precision reddenings and true distance moduli can be determined to individual Galactic Cepheids once distance measurements are available. We illustrate that the relative positioning of stars in the Cepheid period–luminosity (PL) relation (Leavitt law) is preserved as a function of wavelength. This information then provides a powerful constraint for determining reddenings to individual Cepheids, as well as their distances. As a first step, we apply this method to the 59 Cepheids in the compilation of Fouqué et al. Updated reddenings, distance moduli (or parallaxes), and absolute magnitudes in seven (optical through near-infrared) bands are given. From these intrinsic quantities, multiwavelength PL and color–color relations are derived. We find that the V -band period–luminosity–color relation has an rms scatter of only 0.06 mag, so that individual Cepheid distances can be measured to 3%, compared with dispersions of 6 to 13% for the one-parameter K through B PL relations, respectively. This method will be especially useful in conjunction with the new accurate parallax sample upcoming from Gaia .

Distance determination of NPP and oil reservoir on enhanced oil recovery based on heat loss and safety in view point

International Nuclear Information System (INIS)

Erlan Dewita; Dedy Priambodo; Sudi Ariyanto

2013-01-01

EOR is a method used to increasing oil recovery by injecting material or other to the reservoir. There are 3 EOR technique have been used in the world, namely thermal injection, chemical injection dan Miscible. Thermal injection method is the method most widely used in the world, however, one drawback is the loss of heat during steam distribution to the injection wells. In Indonesia, EOR application has been successfully done in the field of Duri, Chevron uses steam injection method, but still use petroleum as a fuel for steam production. In order to save oil reserves, it was done the introduction of co-generation nuclear power plants to supply some of the heat of nuclear power plants for EOR processes. In cogeneration nuclear power plant, the safety aspect is main priority. The purpose of the study was to evaluate the distance NPP with oil wells by considering heat loss and safety aspects. The method of study and calculations done using Tempo Cycle program. The study results showed that in the distance of 400 meter as exclusion zone of PBMR reactor, with pipe insulation thickness 1 in, the amount of heat loss of 277, 883 kw, while in pipe isolation thickness 2 in, amount of heat loss became 162,634 kw and with isolation thickness 3 in, amount of heat loss 120,767 kw., heat loss can be overcome and provide insulation pipes and improve the quality of saturated steam into superheated. (author)

Distance to Cannabis-Shops and Age of Onset of Cannabis Use

NARCIS (Netherlands)

Palali, A.; van Ours, J.C.

2013-01-01

Abstract: In the Netherlands cannabis use is quasi-legalized. Small quantities of cannabis can be bought in cannabis-shops. We investigate how the distance to the nearest cannabis- shop affects the age of onset of cannabis use. We use a Mixed Proportional Hazard rate framework to take account of

Car Stopping Distance on a Tabletop

Science.gov (United States)

Haugland, Ole Anton

2013-01-01

Stopping distances in car braking can be an intriguing topic in physics teaching. It illustrates some basic principles of physics, and sheds valuable light on students' attitude towards aggressive driving. Due to safety considerations, it can be difficult to make experiments with actual car braking. (Contains 2 figures.)

30 CFR 56.4402 - Safety can use.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Safety can use. 56.4402 Section 56.4402 Mineral... and Combustible Liquids and Gases § 56.4402 Safety can use. Small quantities of flammable liquids drawn from storage shall be kept in safety cans labeled to indicate the contents. ...

30 CFR 57.4402 - Safety can use.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Safety can use. 57.4402 Section 57.4402 Mineral... Flammable and Combustible Liquids and Gases § 57.4402 Safety can use. Small quantities of flammable liquids drawn from storage shall be kept in safety cans labeled to indicate the contents. ...

Is 2 mm a safe distance from the inferior alveolar canal to avoid ...

African Journals Online (AJOL)

. Conclusion: When 2 mm is considered as a safety distance, the distance of the implants to the IAC did not yield any statistical difference regarding postoperative neurosensory complications. Keywords: Dental implants, inferior alveolar nerve ...

Representing distance, consuming distance

DEFF Research Database (Denmark)

Larsen, Gunvor Riber

Title: Representing Distance, Consuming Distance Abstract: Distance is a condition for corporeal and virtual mobilities, for desired and actual travel, but yet it has received relatively little attention as a theoretical entity in its own right. Understandings of and assumptions about distance...... are being consumed in the contemporary society, in the same way as places, media, cultures and status are being consumed (Urry 1995, Featherstone 2007). An exploration of distance and its representations through contemporary consumption theory could expose what role distance plays in forming...

Vocal effort with changing talker-to-listener distance in different acoustic environments

DEFF Research Database (Denmark)

Pelegrin Garcia, David; Smits, Bertrand; Brunskog, Jonas

2011-01-01

Talkers adjust their vocal effort to communicate at different distances, aiming to compensate for the sound propagation losses. The present paper studies the influence of four acoustically different rooms on the speech produced by 13 male talkers addressing a listener at four distances. Talkers...... raised their vocal intensity by between 1.3 and 2.2 dB per double distance to the listener and lowered it as a linear function of the quantity “room gain” at a rate of 3.6 dB/dB. There were also significant variations in the mean fundamental frequency, both across distance (3.8 Hz per double distance......) and among environments (4.3 Hz), and in the long-term standard deviation of the fundamental frequency among rooms (4 Hz). In the most uncomfortable rooms to speak in, talkers prolonged the voiced segments of the speech they produced, either as a side-effect of increased vocal intensity or in order...

Multi-objective decoupling algorithm for active distance control of intelligent hybrid electric vehicle

Science.gov (United States)

Luo, Yugong; Chen, Tao; Li, Keqiang

2015-12-01

The paper presents a novel active distance control strategy for intelligent hybrid electric vehicles (IHEV) with the purpose of guaranteeing an optimal performance in view of the driving functions, optimum safety, fuel economy and ride comfort. Considering the complexity of driving situations, the objects of safety and ride comfort are decoupled from that of fuel economy, and a hierarchical control architecture is adopted to improve the real-time performance and the adaptability. The hierarchical control structure consists of four layers: active distance control object determination, comprehensive driving and braking torque calculation, comprehensive torque distribution and torque coordination. The safety distance control and the emergency stop algorithms are designed to achieve the safety and ride comfort goals. The optimal rule-based energy management algorithm of the hybrid electric system is developed to improve the fuel economy. The torque coordination control strategy is proposed to regulate engine torque, motor torque and hydraulic braking torque to improve the ride comfort. This strategy is verified by simulation and experiment using a forward simulation platform and a prototype vehicle. The results show that the novel control strategy can achieve the integrated and coordinated control of its multiple subsystems, which guarantees top performance of the driving functions and optimum safety, fuel economy and ride comfort.

Uncorrected and Corrected Distance Visual Acuity, Predictability, Efficacy, and Safety after Femtosecond Laser in Situ Keratomileusis (FS-LASIK) and Refractive Lenticule extraction (ReLEx) for Moderate and High Myopia

DEFF Research Database (Denmark)

Vestergaard, Anders; Justesen, Birgitte Larsen; Melsen, Charlotte

Title: Uncorrected and Corrected Distance Visual Acuity, Predictability, Efficacy, and Safety after Femtosecond Laser in Situ Keratomileusis (FS-LASIK) and Refractive Lenticule extraction (ReLEx) for Moderate and High Myopia. Vestergaard A., Justesen B., Melsen C., Lyhne N., Department of Ophthal......Title: Uncorrected and Corrected Distance Visual Acuity, Predictability, Efficacy, and Safety after Femtosecond Laser in Situ Keratomileusis (FS-LASIK) and Refractive Lenticule extraction (ReLEx) for Moderate and High Myopia. Vestergaard A., Justesen B., Melsen C., Lyhne N., Department...... predictability, efficacy and safety after femtosecond LASIK (FS-LASIK) with ReLEx. Setting: Department of Ophthalmology, Odense University Hospital, Denmark. Methods: Retrospective study of results after FS-LASIK and ReLEx (including ReLEx flex, ReLEx pseudo-smile, and ReLEx smile). In total, 228 eyes were...... treated with FS-LASIK and 83 eyes with ReLEx, at the Department of Ophthalmology, Odense University Hospital in the period of April to November 2011. Only otherwise healthy myopic eyes with up to 3.00 D of astigmatism and with CDVA ≤ 0.30 (logMAR) before surgery were included in this study. FS-LASIK flaps...

Navy Supply: Economic Order Quantity and Item Essentiality Need More Consideration.

Science.gov (United States)

1988-01-06

Risk and Essentiality Need To compute safety levels, the Navy uses a set of mathematical formulas to Be Recognized that considers such factors as demand...OderQtia~tit ma Safty Lvel -" " Chapter 2 EOQ Principle Not Followed To reduce the purchase workload, the Navy adopted a policy in fiscal year 1985 that...than a minimum of 1 year’s supply. Navy Policy Overrides The EoQ principle is a mathematical technique for determining the pur- chase quantity that will

Quantity Stickiness versus Stackelberg Leadership

International Nuclear Information System (INIS)

Ferreira, F. A.

2008-01-01

We study the endogenous Stackelberg relations in a dynamic market. We analyze a twice-repeated duopoly where, in the beginning, each firm chooses either a quantity-sticky production mode or a quantity-flexible production mode. The size of the market becomes observable after the first period. In the second period, a firm can adjust its quantity if, and only if, it has adopted the flexible mode. Hence, if one firm chooses the sticky mode whilst the other chooses the flexible mode, then they respectively play the roles of a Stackelberg leader and a Stackelberg follower in the second marketing period. We compute the supply quantities at equilibrium and the corresponding expected profits of the firms. We also analyze the effect of the slope parameter of the demand curve on the expected supply quantities and on the profits.

Numeric model to predict the location of market demand and economic order quantity for retailers of supply chain

Science.gov (United States)

Fradinata, Edy; Marli Kesuma, Zurnila

2018-05-01

Polynomials and Spline regression are the numeric model where they used to obtain the performance of methods, distance relationship models for cement retailers in Banda Aceh, predicts the market area for retailers and the economic order quantity (EOQ). These numeric models have their difference accuracy for measuring the mean square error (MSE). The distance relationships between retailers are to identify the density of retailers in the town. The dataset is collected from the sales of cement retailer with a global positioning system (GPS). The sales dataset is plotted of its characteristic to obtain the goodness of fitted quadratic, cubic, and fourth polynomial methods. On the real sales dataset, polynomials are used the behavior relationship x-abscissa and y-ordinate to obtain the models. This research obtains some advantages such as; the four models from the methods are useful for predicting the market area for the retailer in the competitiveness, the comparison of the performance of the methods, the distance of the relationship between retailers, and at last the inventory policy based on economic order quantity. The results, the high-density retail relationship areas indicate that the growing population with the construction project. The spline is better than quadratic, cubic, and four polynomials in predicting the points indicating of small MSE. The inventory policy usages the periodic review policy type.

VCSEL-based sensors for distance and velocity

Science.gov (United States)

Moench, Holger; Carpaij, Mark; Gerlach, Philipp; Gronenborn, Stephan; Gudde, Ralph; Hellmig, Jochen; Kolb, Johanna; van der Lee, Alexander

2016-03-01

VCSEL based sensors can measure distance and velocity in three dimensional space and are already produced in high quantities for professional and consumer applications. Several physical principles are used: VCSELs are applied as infrared illumination for surveillance cameras. High power arrays combined with imaging optics provide a uniform illumination of scenes up to a distance of several hundred meters. Time-of-flight methods use a pulsed VCSEL as light source, either with strong single pulses at low duty cycle or with pulse trains. Because of the sensitivity to background light and the strong decrease of the signal with distance several Watts of laser power are needed at a distance of up to 100m. VCSEL arrays enable power scaling and can provide very short pulses at higher power density. Applications range from extended functions in a smartphone over industrial sensors up to automotive LIDAR for driver assistance and autonomous driving. Self-mixing interference works with coherent laser photons scattered back into the cavity. It is therefore insensitive to environmental light. The method is used to measure target velocity and distance with very high accuracy at distances up to one meter. Single-mode VCSELs with integrated photodiode and grating stabilized polarization enable very compact and cost effective products. Besides the well know application as computer input device new applications with even higher accuracy or for speed over ground measurement in automobiles and up to 250km/h are investigated. All measurement methods exploit the known VCSEL properties like robustness, stability over temperature and the potential for packages with integrated optics and electronics. This makes VCSEL sensors ideally suited for new mass applications in consumer and automotive markets.

Quantities and Units used in Radiation Safety. Address at the third national course of Radiation Safety in Radiology. May 22-24, 2000 Guatemala

International Nuclear Information System (INIS)

Dieguez, Lazaro

2000-05-01

The address discusses the following issues: the radiological units, radiation dose units, radiation protection units and operational quantities used for individual monitoring recently introduced by the International Commission of Radiological Units

How necessary are the new quantities

International Nuclear Information System (INIS)

Kraus, W.

1991-01-01

The necessity of the ICRU operational quantities is discussed from the point of view of practical, opertional radiation protection, on the basis of ICRU report 43. It is clear that, although the new quantities have some advantages over previous systems of operational quantities, there are some disadvantages as well. The decision to adopt these quantities is, therefore, not clear cut. (orig.)

DISTANCES TO DARK CLOUDS: COMPARING EXTINCTION DISTANCES TO MASER PARALLAX DISTANCES

International Nuclear Information System (INIS)

Foster, Jonathan B.; Jackson, James M.; Stead, Joseph J.; Hoare, Melvin G.; Benjamin, Robert A.

2012-01-01

We test two different methods of using near-infrared extinction to estimate distances to dark clouds in the first quadrant of the Galaxy using large near-infrared (Two Micron All Sky Survey and UKIRT Infrared Deep Sky Survey) surveys. Very long baseline interferometry parallax measurements of masers around massive young stars provide the most direct and bias-free measurement of the distance to these dark clouds. We compare the extinction distance estimates to these maser parallax distances. We also compare these distances to kinematic distances, including recent re-calibrations of the Galactic rotation curve. The extinction distance methods agree with the maser parallax distances (within the errors) between 66% and 100% of the time (depending on method and input survey) and between 85% and 100% of the time outside of the crowded Galactic center. Although the sample size is small, extinction distance methods reproduce maser parallax distances better than kinematic distances; furthermore, extinction distance methods do not suffer from the kinematic distance ambiguity. This validation gives us confidence that these extinction methods may be extended to additional dark clouds where maser parallaxes are not available.

Transactional distance in a blended learning environment

Directory of Open Access Journals (Sweden)

Jon Dron

2004-12-01

Full Text Available This paper presents a case study that describes and discusses the problems encountered during the design and implementation of a blended learning course, largely taught online through a web-based learning environment. Based on Moore's theory of transactional distance, the course was explicitly designed to have dialogue at its heart. However, the reality of systemic behaviours caused by delivering such a course within a group of conventional further and higher educational institutions has led to an entirely unanticipated reversion to structure, with unpleasant consequences for both quality and quantity of dialogue. The paper looks at some of the reasons for this drift, and suggests that some of the disappointing results (in particular in terms of the quality of the students' experience and associated poor retention can be attributed to the lack of dialogue, and consequent increase in transactional distance. It concludes with a description and evaluation of steps currently being taken to correct this behaviour.

Entity-Linking via Graph-Distance Minimization

Directory of Open Access Journals (Sweden)

Roi Blanco

2014-07-01

Full Text Available Entity-linking is a natural-language–processing task that consists in identifying the entities mentioned in a piece of text, linking each to an appropriate item in some knowledge base; when the knowledge base is Wikipedia, the problem comes to be known as wikification (in this case, items are wikipedia articles. One instance of entity-linking can be formalized as an optimization problem on the underlying concept graph, where the quantity to be optimized is the average distance between chosen items. Inspired by this application, we define a new graph problem which is a natural variant of the Maximum Capacity Representative Set. We prove that our problem is NP-hard for general graphs; nonetheless, under some restrictive assumptions, it turns out to be solvable in linear time. For the general case, we propose two heuristics: one tries to enforce the above assumptions and another one is based on the notion of hitting distance; we show experimentally how these approaches perform with respect to some baselines on a real-world dataset.

Distance-Based Access Modifiers Applied to Safety in Home Networks

DEFF Research Database (Denmark)

Mortensen, Kjeld Høyer; Schougaard, Kari Rye; Schultz, Ulrik Pagh

2004-01-01

Home networks and the interconnection of home appliances is a classical theme in ubiquitous computing research. Security is a recurring concern, but there is a lack of awareness of safety: preventing the computerized house from harming the inhabitants, even in a worst-case scenario where...... be performed within a physical proximity that ensures safety. We use a declarative approach integrated with an IDL language to express location-based restrictions on operations. This model has been implemented in a middleware for home audio-video devices, using infrared communication and a local-area network...

Supply chain management - safety aspects

Directory of Open Access Journals (Sweden)

2010-12-01

Full Text Available Developing economy, growing customer requirements and competition make the service level higher. Delivery safety - as the highest priority - has to be maintained at the same time. Customers more and more often require transport to be very flexible, fast, and complex in terms of carrying every quantity of goods of different sizes, from and to different countries, through customs clearance, storing and distribution of shipments. Meeting these requirements depends on complex information on transport processes and their safety. The article presents safety foundations and institution Authorized Economic Operator - AEO in supply chains.

Checklists, safety, my culture and me.

Science.gov (United States)

Raghunathan, Karthik

2012-07-01

The world is not flat. Hierarchy is a fact of life in society and in healthcare institutions. National, specialty-specific and institutional cultures may play an important role in shaping today's patient-safety climate. The influence of power distance on safety interventions is under-studied. Checklists may make power distance-hampered negotiations easier by providing a standardised aviation-like framework for communications and by democratising the environment. By using surveys and simulation, we might discover patterns of potentially hidden yet problematic interactions that might foster maintenance of the error swamp. We need to understand how people interact as members of a group as this is crucial for the development of generalisable safety interventions.

Radiation quantities and units

International Nuclear Information System (INIS)

1980-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. In line, with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection 1.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. As in ICRU Report 19, the definitions of quantities and units specifically designed for radiation protection (Part B) are separated from those of the general quantities (Part A). The inclusion of the index concept outlined in ICRU Report 25[4] required an extension of Part B

Firefighter Safety Zone: The effect of terrain slope of separation distance

Science.gov (United States)

Bret Butler; Jason Forthofer

2010-01-01

Perhaps one of the most critical decisions made on wildland fires is the identification of suitable safety zones for firefighters during daily fire management operations. To be effective (timely, repeatable, and accurate), these decisions rely on good training and good judgement. The current safety zone guidelines used in the US (see fig. 1) and published in the...

Are necessary unmeasurable quantities in radiation protection?

International Nuclear Information System (INIS)

David, M.G.; Correa, M.F.; Videira, A.A.P.

2016-01-01

We discuss in this paper the metrological status of unmeasurable protection quantities and the need to maintain these kind of quantities in the system. The discussion is based on reports from the institutions responsible for the quantities and on scientific publications. In conclusion, we can say that there are alternatives for changing the system in a way that it keep just measurable quantities, nevertheless the present system is well assimilated. Even though a proposal yet to be presented for changing the system, although might simplify and improve it, is not intended to overcome the existence of unmeasurable quantities or the two kinds of quantities. (author)

SafetyNet. Human factors safety training on the Internet

DEFF Research Database (Denmark)

Hauland, G.; Pedrali, M.

2002-01-01

This report describes user requirements to an Internet based distance learning system of human factors training, i.e. the SafetyNet prototype, within the aviation (pilots and air traffic control), maritime and medical domains. User requirements totraining have been elicited through 19 semi...

Calculation of Hazard Category 2/3 Threshold Quantities Using Contemporary Dosimetric Data

Energy Technology Data Exchange (ETDEWEB)

Walker, William C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-11-01

The purpose of this report is to describe the methodology and selection of input data utilized to calculate updated Hazard Category 2 and Hazard Category 3 Threshold Quantities (TQs) using contemporary dosimetric information. The calculation of the updated TQs will be considered for use in the revision to the Department of Energy (DOE) Technical Standard (STD-) 1027-92 Change Notice (CN)-1, “Hazard Categorization and Accident Analysis Techniques for Compliance with DOE Order 5480.23, Nuclear Safety Analysis Reports.” The updated TQs documented in this report complement an effort previously undertaken by the National Nuclear Security Administration (NNSA), which in 2014 issued revised Supplemental Guidance documenting the calculation of updated TQs for approximately 100 radionuclides listed in DOE-STD-1027-92, CN-1. The calculations documented in this report complement the NNSA effort by expanding the set of radionuclides to more than 1,250 radionuclides with a published TQ. The development of this report was sponsored by the Department of Energy’s Office of Nuclear Safety (AU-30) within the Associate Under Secretary for Environment, Health, Safety, and Security organization.

A comparison between using distance sensors for measuring the pantograph vertically movement

Science.gov (United States)

Rob, R.; Panoiu, C.; Rusu-Anghel, S.; Panoiu, M.

2018-01-01

In railway transportation the most important problem to solve consists in assuring the safety traffic of people and freight. In this scope some of the geometrical parameters regarding the contact line must be measured. One of this parameter is the pantograph vertically movement, so it must use distance sensors. Present paper studies the performance of two kinds of distance sensors, an ultrasonic distance sensor and an infrared sensor. The performances are studied from the point of view of error distance measurement and the possibility of using a real time acquisition system. The researches were made on a laboratory model for the pantograph realized at the scale 1:2.

Design of an Active Automotive Safety System

Directory of Open Access Journals (Sweden)

Y. Wang

2013-07-01

Full Text Available With the development of the national economy, the people's standard of living got corresponding improvement, cars has been one of the indispensable traffic tools in many families. An active safety system is proposed, which can real-time detect the vehicle's running status and judge the security status of the vehicle. The system, which takes single-chip microcomputer as the controlling core and combines with millimeter-wave and ultrasonic distance measurement technology, can detect the distance from vehicle to vehicle and judge the security status of the vehicle. The hardware composition of the system and the data acquiring circuit are proposed, the mathematic model for different situation is established, and the controlling algorithm is completed. This system can accurately measure speed and distance between vehicles; the active safety control system can meet the relevant data measurement and transmission requirement; and can meet the functional requirement of the active safety control system

Regulatory and extra-regulatory testing to demonstrate radioactive material packaging safety

International Nuclear Information System (INIS)

Ammerman, D.J.

1997-01-01

Packages for the transportation of radioactive material must meet performance criteria to assure safety and environmental protection. The stringency of the performance criteria is based on the degree of hazard of the material being transported. Type B packages are used for transporting large quantities of radioisotopes (in terms of A 2 quantities). These packages have the most stringent performance criteria. Material with less than an A 2 quantity are transported in Type A packages. These packages have less stringent performance criteria. Transportation of LSA and SCO materials must be in open-quotes strong-tightclose quotes packages. The performance requirements for the latter packages are even less stringent. All of these package types provide a high level of safety for the material being transported. In this paper, regulatory tests that are used to demonstrate this safety will be described. The responses of various packages to these tests will be shown. In addition, the response of packages to extra-regulatory tests will be discussed. The results of these tests will be used to demonstrate the high level of safety provided to workers, the public, and the environment by packages used for the transportation of radioactive material

Fitting polynomial surfaces to triangular meshes with Voronoi squared distance minimization

KAUST Repository

Nivoliers, Vincent

2012-11-06

This paper introduces Voronoi squared distance minimization (VSDM), an algorithm that fits a surface to an input mesh. VSDM minimizes an objective function that corresponds to a Voronoi-based approximation of the overall squared distance function between the surface and the input mesh (SDM). This objective function is a generalization of the one minimized by centroidal Voronoi tessellation, and can be minimized by a quasi-Newton solver. VSDM naturally adapts the orientation of the mesh elements to best approximate the input, without estimating any differential quantities. Therefore, it can be applied to triangle soups or surfaces with degenerate triangles, topological noise and sharp features. Applications of fitting quad meshes and polynomial surfaces to input triangular meshes are demonstrated. © 2012 Springer-Verlag London.

Fleet analysis of headway distance for autonomous driving.

Science.gov (United States)

Ivanco, Andrej

2017-12-01

Modern automobiles are going through a paradigm shift, where the driver may no longer be needed to drive the vehicle. As the self-driving vehicles are making their way to public roads the automakers have to ensure the naturalistic driving feel to gain drivers' confidence and accelerate adoption rates. This paper filters and analyzes a subset of radar data collected from SHRP2 with focus on characterizing the naturalistic headway distance with respect to the vehicle speed. The paper identifies naturalistic headway distance and compares it with the previous findings from the literature. A clear relation between time headway and speed was confirmed and quantified. A significant difference exists among individual drivers which supports a need to further refine the analysis. By understanding the relationship between human driving and their surroundings, the naturalistic driving behavior can be quantified and used to increase the adoption rates of autonomous driving. Dangerous and safety-compromising driving can be identified as well in order to avoid its replication in the control algorithms. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

Transportation Safety Excellence in Operations Through Improved Transportation Safety Document

International Nuclear Information System (INIS)

Dr. Michael A. Lehto; MAL

2007-01-01

A recent accomplishment of the Idaho National Laboratory (INL) Materials and Fuels Complex (MFC) Nuclear Safety analysis group was to obtain DOE-ID approval for the inter-facility transfer of greater-than-Hazard-Category-3 quantity radioactive/fissionable waste in Department of Transportation (DOT) Type A drums at MFC. This accomplishment supported excellence in operations through safety analysis by better integrating nuclear safety requirements with waste requirements in the Transportation Safety Document (TSD); reducing container and transport costs; and making facility operations more efficient. The MFC TSD governs and controls the inter-facility transfer of greater-than-Hazard-Category-3 radioactive and/or fissionable materials in non-DOT approved containers. Previously, the TSD did not include the capability to transfer payloads of greater-than-Hazard-Category-3 radioactive and/or fissionable materials using DOT Type A drums. Previous practice was to package the waste materials to less-than-Hazard-Category-3 quantities when loading DOT Type A drums for transfer out of facilities to reduce facility waste accumulations. This practice allowed operations to proceed, but resulted in drums being loaded to less than the Waste Isolation Pilot Plant (WIPP) waste acceptance criteria (WAC) waste limits, which was not cost effective or operations friendly. An improved and revised safety analysis was used to gain DOE-ID approval for adding this container configuration to the MFC TSD safety basis. In the process of obtaining approval of the revised safety basis, safety analysis practices were used effectively to directly support excellence in operations. Several factors contributed to the success of MFC's effort to obtain approval for the use of DOT Type A drums, including two practices that could help in future safety basis changes at other facilities. (1) The process of incorporating the DOT Type A drums into the TSD at MFC helped to better integrate nuclear safety

Thermal quantities of 46Ti

International Nuclear Information System (INIS)

Rahmatinejad, A.; Razavi, R.; Kakavand, T.

2015-01-01

Thermodynamic quantities of 46 Ti have been calculated in the framework of the BCS model with inclusion of modified nuclear pairing gap (MPBCS) that was proposed in our previous publication. Using modified paring gap results in an S-shaped heat capacity curve at critical temperature with a smooth behavior instead of singular behavior of the same curve in the BCS calculations. In addition the thermal quantities have been extracted within the framework of a canonical ensemble according to the new experimental data on nuclear level densities measured by the Oslo group. Comparison shows a good agreement between our calculations in MPBCS and the extracted quantities in the canonical ensemble framework

Safety aspects of siting

International Nuclear Information System (INIS)

Rosen, M.

1976-01-01

Outline of parameters to be considered in site selection, radiation safety, and mechanisms of radiation release. Radiation doses in tablular form for areas at various distances from the plant. (HP) [de

The assessment of the safety and the radiological risks associated with the transport of radioactive wastes in Romania

International Nuclear Information System (INIS)

Vieru, G.

2000-01-01

Problems related to the handling, treatment, packaging, storage, transportation, and disposal of radioactive wastes (radwastes) are very important and the responsibility for the safe management of radioactive wastes for the protection of human health and the environment has long been recognized. Safety and public welfare are to be considered within the radioactive waste management, particularly in the field of transportation because of the potential risk that it could pose to the public and to the environment. The IAEA regulations ensure safety in the transport of Radioactive Materials (RAM) by laying down detailed requirements, appropriate to the degree of hazard represented by the respective material, taking into account its form and quantity. Risk assessment provides a basis for routing radwastes and developing mitigation plans, prioritizing initiatives and enacting legislation to protect human beings and the environment. Factors such as shipment cost, distance, population exposed, environmental impacts or sensitivity, time in transit and infrastructure related issues, could be included in the terms of safety and risk. The paper presents risk assessment activities aimed to evaluate risk categories and the radiological consequences that may arise during normal (accident free) transport and those resulting from transport accidents involving waste shipments in Romania. (author)

Vegetative provision of central hemodynamics and physical performance of middle distance sportswomen-runners

Directory of Open Access Journals (Sweden)

E. L. Mikhalyuk

2014-04-01

Full Text Available Aims. To determine the autonomic provision of the central hemodynamics and physical performance in middle distance sportswomen-runners. Methods and results. A comprehensive survey of 34 sportswomen-sprinters, qualifications from II-III level to the IMS, was carried out. For the analysis of vegetative cardiovascular regulation mathematical methods of HRV were used. In middle distance sportswomen-runners with qualifications of MS-IMS parasympathetic link of autonomic nervous system, hypokinetic types of circulation, large quantities of physical performance and index of functional state prevail compared with sportswomen-runners with qualifications of CMS, I-st, II-nd and III-rd level. Conclusion. Correlation analysis showed a significant interconnection, indicating that the optimal vegetative providing of training process of middle distance runners is accompanied by hypokinetic TC and high digits of PWC170/kg and IFS.

Quantities for environmental monitoring

International Nuclear Information System (INIS)

1989-01-01

It is recommended that if measurements are made with the objective of monitor radiation levels in the environment to elucidate long-term changes in these levels, then air kerma should be used. If the objective is to give an indication that levels from man-made sources are acceptable within specified limits for the exposure of people, then ambient dose equivalent should be used. It should be noted that radiation risks to individuals are best expressed by the quantity effective dose equivalent. If this latter quantity is to be accurately assessed, it may be necessary to obtain details of the quality of the environmental radiation that cannot be described adequately by simple measurements of either air kerma or ambient dose equivalent. If the above objectives pertain, the measurements should record both air kerma and ambient dose equivalent. If neutrons are measured in the environment then ambient dose equivalent is the appropriate quantity for both the above objectives. (author)

The effects of power, leadership and psychological safety on resident event reporting.

Science.gov (United States)

Appelbaum, Nital P; Dow, Alan; Mazmanian, Paul E; Jundt, Dustin K; Appelbaum, Eric N

2016-03-01

Although the reporting of adverse events is a necessary first step in identifying and addressing lapses in patient safety, such events are under-reported, especially by frontline providers such as resident physicians. This study describes and tests relationships between power distance and leader inclusiveness on psychological safety and the willingness of residents to report adverse events. A total of 106 resident physicians from the departments of neurosurgery, orthopaedic surgery, emergency medicine, otolaryngology, neurology, obstetrics and gynaecology, paediatrics and general surgery in a mid-Atlantic teaching hospital were asked to complete a survey on psychological safety, perceived power distance, leader inclusiveness and intention to report adverse events. Perceived power distance (β = -0.26, standard error [SE] 0.06, 95% confidence interval [CI] -0.37 to 0.15; p leadership practices build psychological safety and minimise power distance between low- and high-status members in order to support greater reporting of adverse events. © 2016 John Wiley & Sons Ltd.

Extremely long-distance seed dispersal by an overfished Amazonian frugivore.

Science.gov (United States)

Anderson, Jill T; Nuttle, Tim; Saldaña Rojas, Joe S; Pendergast, Thomas H; Flecker, Alexander S

2011-11-22

Throughout Amazonia, overfishing has decimated populations of fruit-eating fishes, especially the large-bodied characid, Colossoma macropomum. During lengthy annual floods, frugivorous fishes enter vast Amazonian floodplains, consume massive quantities of fallen fruits and egest viable seeds. Many tree and liana species are clearly specialized for icthyochory, and seed dispersal by fish may be crucial for the maintenance of Amazonian wetland forests. Unlike frugivorous mammals and birds, little is known about seed dispersal effectiveness of fishes. Extensive mobility of frugivorous fish could result in extremely effective, multi-directional, long-distance seed dispersal. Over three annual flood seasons, we tracked fine-scale movement patterns and habitat use of wild Colossoma, and seed retention in the digestive tracts of captive individuals. Our mechanistic model predicts that Colossoma disperses seeds extremely long distances to favourable habitats. Modelled mean dispersal distances of 337-552 m and maximum of 5495 m are among the longest ever reported. At least 5 per cent of seeds are predicted to disperse 1700-2110 m, farther than dispersal by almost all other frugivores reported in the literature. Additionally, seed dispersal distances increased with fish size, but overfishing has biased Colossoma populations to smaller individuals. Thus, overexploitation probably disrupts an ancient coevolutionary relationship between Colossoma and Amazonian plants.

Probabilistic optimization of safety coefficients

International Nuclear Information System (INIS)

Marques, M.; Devictor, N.; Magistris, F. de

1999-01-01

This article describes a reliability-based method for the optimization of safety coefficients defined and used in design codes. The purpose of the optimization is to determine the partial safety coefficients which minimize an objective function for sets of components and loading situations covered by a design rule. This objective function is a sum of distances between the reliability of the components designed using the safety coefficients and a target reliability. The advantage of this method is shown on the examples of the reactor vessel, a vapour pipe and the safety injection circuit. (authors)

When safety rhymes with transparency

International Nuclear Information System (INIS)

Champion, Marion; Larroque, Damien; Vandermersch, Marie

2009-01-01

The Transparency and Nuclear Safety Act, which took effect in 2006, requires each operator to document the measures taken to ensure nuclear safety and radiological protection and to list incidents and accidents as well as actions taken to protect the environment. This specifies the nature and limits of radioactive and non-radioactive releases, the quantity of waste to be stored at the facility, actions taken to limit waste volume, and effects on health and the environment, especially on soil and water. (authors)

Method and means for determining heat quantities

Energy Technology Data Exchange (ETDEWEB)

Waasdorp, G G; de Jong, J J; Bijl, A

1965-08-24

To determine the quantity of potential heat W that has flowed past a certain point in a certain time, the velocity of the combustible Q, the temperature T, and the specific gravity YDTU are measured, and these values are transmitted to a computer which automatically calculates the quantity: ..pi..EQUATION/sup -/ in which delta T is the difference between the combustible temperature T and a reference temperature, and in which the relation f(YDTU, delta T) represents the heat of combustion as a function of the quantities YDTU and delta T and possibly other properties of the combustible. Alternatively the quantity: ..pi..EQUATION/sup -/ may be measured; here the quantities have the same meaning as above.

A Viewpoint on the Quantity "Plane Angle"

Science.gov (United States)

Eder, W. E.

1982-01-01

Properties of the quantity "plane angle" are explored under the hypothesis that it is a dimensional quantity. The exploration proceeds especially with respect to the physical concept, its mathematical treatment, vector concepts, measurement theory, units of related quantities, engineering pragmatism, and SI. An attempt is made to bring these different relations into a rational, logical and consistent framework, and thus to justify the hypothesis. Various types of vectorial quantities are recognized, and their properties described with an outline of the necessary algebraic manipulations. The concept of plane angle is amplified, and its interdependence with the circular arc is explored. The resulting units of plane angle form a class of similar scales of measurement. Consequences of the confirmed hypothesis are developed for mathematical expressions involving trigonometric functions, rotational volumes and areas, mathematical limits, differentiation and series expansion. Consequences for mechanical rotational quantities are developed, with proposals for revisions to a number of expressions for derived units within SI. A revised definition for the quantity "plane angle" is stated to take account of the developed insights. There is a clear need to reconsider the status of plane angle and some other quantities within the international framework of SI.

Emission sources and quantities

International Nuclear Information System (INIS)

Heinen, B.

1991-01-01

The paper examines emission sources and quantities for SO 2 and NO x . Natural SO 2 is released from volcanic sources and to a much lower extent from marsh gases. In nature NO x is mainly produced in the course of the chemical and bacterial denitrification processes going on in the soil. Manmade pollutants are produced in combustion processes. The paper concentrates on manmade pollution. Aspects discussed include: mechanism of pollution development; manmade emission sources (e.g. industry, traffic, power plants and domestic sources); and emission quantities and forecasts. 11 refs., 2 figs., 5 tabs

Influence of relative humidity and temperature on quantity of electric charge of static protective clothing used in petrochemical industry

Science.gov (United States)

Zhang, Yunpeng; Liu, Quanzhen; Liu, Baoquan; Li, Yipeng; Zhang, Tingting

2013-03-01

In this paper, the working principle of static protective clothing and its testing method of quantity of electric charge are introduced, and the influence of temperature and relative humidity on the quantity of electric charge (qe) of static protective clothing is studied by measuring qe of different clothing samples. The result shows that temperature and relative humidity can influence qe of static protective clothing to some extent and the influence of relative humidity is bigger than that of temperature. According to experimental results, the relationship of qe and relative humidity and temperature was analysed, and the safety boundary of quantity of electric charge is discussed. In order to reduce the occurrence of electrostatic accidents and ensure safe production and operation of petrochemical industry, some suggestions on choosing and using of static protective clothing are given for guaranteeing its static protective performance.

Theoretical investigation of shock stand-off distance for non-equilibrium flows over spheres

KAUST Repository

Shen, Hua

2018-02-20

We derived a theoretical solution of the shock stand-off distance for a non-equilibrium flow over spheres based on Wen and Hornung’s solution and Olivier’s solution. Compared with previous approaches, the main advantage of the present approach is allowing an analytic solution without involving any semi-empirical parameter for the whole non-equilibrium flow regimes. The effects of some important physical quantities therefore can be fully revealed via the analytic solution. By combining the current solution with Ideal Dissociating Gas (IDG) model, we investigate the effects of free stream kinetic energy and free stream dissociation level (which can be very different between different facilities) on the shock stand-off distance.

Intraoral Digital Impressions for Virtual Occlusal Records: Section Quantity and Dimensions

Directory of Open Access Journals (Sweden)

Eneko Solaberrieta

2016-01-01

Full Text Available The purpose of this study was to locate the 3D spatial position mandibular cast and determine its occlusal contacts in a novel way by using an intraoral scanner as part of the virtual occlusal record procedure. This study also analyzes the requirements in quantity and dimensions of the intraoral virtual occlusal record. The results showed that the best section combination consists of 2 lateral and frontal sections, the width of this section being that of 2 teeth (24 mm × 15 mm. This study concluded that this procedure was accurate enough to locate the mandibular cast on a virtual articulator. However, at least 2 sections of the virtual occlusal records were necessary, and the best results were obtained when the distance between these sections was maximum.

Intraoral Digital Impressions for Virtual Occlusal Records: Section Quantity and Dimensions

Science.gov (United States)

Solaberrieta, Eneko; Garmendia, Asier; Brizuela, Aritza; Otegi, Jose Ramon; Pradies, Guillermo; Szentpétery, Andras

2016-01-01

The purpose of this study was to locate the 3D spatial position mandibular cast and determine its occlusal contacts in a novel way by using an intraoral scanner as part of the virtual occlusal record procedure. This study also analyzes the requirements in quantity and dimensions of the intraoral virtual occlusal record. The results showed that the best section combination consists of 2 lateral and frontal sections, the width of this section being that of 2 teeth (24 mm × 15 mm). This study concluded that this procedure was accurate enough to locate the mandibular cast on a virtual articulator. However, at least 2 sections of the virtual occlusal records were necessary, and the best results were obtained when the distance between these sections was maximum. PMID:26881226

Development of Broadband Nuclear Safety Data Network (B-NSDN)

International Nuclear Information System (INIS)

Son, Gwang Seop; Kim, Dong Hoon; Park, Gi Yong

2011-01-01

Recently as introducing digital safety system in nuclear power plant, more data transmission capacity is required. Bandwidth of existing communication network is about a few Mbps. Thus data transmission quantity in recently digital safety system is beyond existing communication network's capacity. In this paper, new protocol that is suitable for safety system communication network is designed. FPGA based communication system is implemented. As result of test, effective bandwidth of B-NSDN is about 20Mbps

Epidemiology of road traffic crashes among long distance drivers in ...

African Journals Online (AJOL)

Department of Epidemiology and Medical Statistics, Faculty of Public Health, University of Ibadan, Ibadan. 2. Anaesthetist, Emergency ... long-distance drivers studied. Reconstruction of bad roads and implementation of road safety education ... transport and occur on a traffic way or while the vehi- cle is still in motion after ...

Method of Converting Wheat Flour Quantity into Rice Flour Quantity in Cookies (Part-1)

OpenAIRE

村田,美穂子; 髙橋,由加

2016-01-01

A method of converting the wheat flour quantity of a recipe of wheat-flour cookies into the rice flour quantity of a recipe of rice-flour cookies used domestically for wheat-allergic children was studied. The proportion of the water content with respect to the flour content (the wheat or rice flour content) in cut cookies prepared according to a commercially available recipe was obtained. Next, four types of rice-flour cookies were prepared according to a recipe for wheat-flour cookies using ...

THE USE OF FACEBOOK FOR ONLINE DISCUSSIONS AMONG DISTANCE LEARNERS

Directory of Open Access Journals (Sweden)

Tina LIM

2010-10-01

Full Text Available With the advent of Web 2.0 tools, educators are looking to these new technological tools to examine its potential in enhancing teaching and learning. While its runaway success as a social networking tool is now renowned, the use of Facebook for educational purposes may be considered still at its infancy stage. This paper describes the use of Facebook as a platform for academic discussions among distance learners. It offers a glimpse into how mobile learning via SMS together with Facebook was used to support and enhance the blended learning approach at Open University Malaysia for three courses: Learning Skills for Open and Distance Learners, Company Law and Renal Nursing. Data on user interactions collected were from the “Page Insights” tools available to Page administrators for the whole duration of a course semester. Facebook interactions examined include total number of fans, total interactions, interactions per post, post quality and unique page views. Findings indicate that Facebook does have the potential to draw distance learners to engage in meaningful academic conversations but the quantity and quality of posts very much depends on the timing as well as the topics of discussion.

Critical review of the current radiation protection quantities and units

International Nuclear Information System (INIS)

Sabol, J.

1998-01-01

Examples exist in dosimetry and radiation protection where primary attention was focused on the unit rather than the corresponding quantity. Another difficulty arises from the fact that quantities in this field cannot be considered as pure physical quantities, they are rather biophysical quantities. There are too many quantities (e. g. 17 quantities based on the dose equivalent), with differences in numerical values of 'similar' quantities, not always satisfactory approximations of virtually unmeasurable quantities by measurable quantities, inconsistency in definitions and interpretations of quantities of some international expert bodies, and problems of weighting and conversion factors. (M.D.)

Influence of relative humidity and temperature on quantity of electric charge of static protective clothing used in petrochemical industry

International Nuclear Information System (INIS)

Zhang, Yunpeng; Liu, Quanzhen; Liu, Baoquan; Li, Yipeng; Zhang, Tingting

2013-01-01

In this paper, the working principle of static protective clothing and its testing method of quantity of electric charge are introduced, and the influence of temperature and relative humidity on the quantity of electric charge (q e ) of static protective clothing is studied by measuring q e of different clothing samples. The result shows that temperature and relative humidity can influence q e of static protective clothing to some extent and the influence of relative humidity is bigger than that of temperature. According to experimental results, the relationship of q e and relative humidity and temperature was analysed, and the safety boundary of quantity of electric charge is discussed. In order to reduce the occurrence of electrostatic accidents and ensure safe production and operation of petrochemical industry, some suggestions on choosing and using of static protective clothing are given for guaranteeing its static protective performance.

The new operational quantities for radiation protection

International Nuclear Information System (INIS)

Kellerer, A.M.

1985-01-01

Philosophies and quantities for radiation protection have often been subjected to changes, and some of the developments are traced which ultimately led to recent proposals by ICRU. Development in the past has largely been towards clarification and generalisation of definitions. The present changes, however, reflect a more fundamental issue, the transition from the limitation system to the assessment system in radiation protection. The index quantities were suitable tools to ascertain compliance with the limitation system of radiation protection. The new quantities proposed by ICRU are suitable estimators for effective dose equivalent, which is an essential quantity in the assessment system of radiation protection. A synopsis of the definitions is given. (author)

36 CFR 223.220 - Quantity determination.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 2 2010-07-01 2010-07-01 false Quantity determination. 223.220 Section 223.220 Parks, Forests, and Public Property FOREST SERVICE, DEPARTMENT OF AGRICULTURE SALE AND DISPOSAL OF NATIONAL FOREST SYSTEM TIMBER Special Forest Products § 223.220 Quantity determination...

Evidence for asymptotic safety from lattice quantum gravity.

Science.gov (United States)

Laiho, J; Coumbe, D

2011-10-14

We calculate the spectral dimension for nonperturbative quantum gravity defined via Euclidean dynamical triangulations. We find that it runs from a value of ∼3/2 at short distance to ∼4 at large distance scales, similar to results from causal dynamical triangulations. We argue that the short-distance value of 3/2 for the spectral dimension may resolve the tension between asymptotic safety and the holographic principle.

Conceptual Model of Quantities, Units, Dimensions, and Values

Science.gov (United States)

Rouquette, Nicolas F.; DeKoenig, Hans-Peter; Burkhart, Roger; Espinoza, Huascar

2011-01-01

JPL collaborated with experts from industry and other organizations to develop a conceptual model of quantities, units, dimensions, and values based on the current work of the ISO 80000 committee revising the International System of Units & Quantities based on the International Vocabulary of Metrology (VIM). By providing support for ISO 80000 in SysML via the International Vocabulary of Metrology (VIM), this conceptual model provides, for the first time, a standard-based approach for addressing issues of unit coherence and dimensional analysis into the practice of systems engineering with SysML-based tools. This conceptual model provides support for two kinds of analyses specified in the International Vocabulary of Metrology (VIM): coherence of units as well as of systems of units, and dimension analysis of systems of quantities. To provide a solid and stable foundation, the model for defining quantities, units, dimensions, and values in SysML is explicitly based on the concepts defined in VIM. At the same time, the model library is designed in such a way that extensions to the ISQ (International System of Quantities) and SI Units (Systeme International d Unites) can be represented, as well as any alternative systems of quantities and units. The model library can be used to support SysML user models in various ways. A simple approach is to define and document libraries of reusable systems of units and quantities for reuse across multiple projects, and to link units and quantity kinds from these libraries to Unit and QuantityKind stereotypes defined in SysML user models.

Respect distances. Rationale and means of computation

Energy Technology Data Exchange (ETDEWEB)

Munier, Raymond [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Hoekmark, Harald [Clay Technology, Lund (Sweden)

2004-12-01

Canisters with spent nuclear fuel can obviously not be located within deformation zones as this might jeopardise their long term mechanical stability and thereby constitute a potential hazard to the biosphere. Less apparent, but equally important, is the fact that earthquakes trigger reactivation, slip, of structures some distance from their hypocentres due to, among many other factors, stress redistribution. Fault slip across a deposition hole might damage the isolation capacity of the canister and thereby jeopardise the overall integrity of the barrier system. Therefore, the following question might be posed: What is the distance from a deformation zone beyond which a canister can be safely emplaced? This respect distance cannot be readily computed because, unknown future events aside, there are some complicated aspects that need to be addressed e.g. degree of conservatism, scale, our ability to model ice sheets and earthquakes, etc. In this report we discuss various aspects of the assignment of respect distances, propose a methodology for its assignment and apply the methodology to the Forsmark Site as a worked example. Our main concern, in the context discussed in this report, is the post glacial faults anticipated to occur after the next glaciations. To properly address conservativeness, analysis of risk, and its implementation in safety analysis, we provide an extensive compilation of our current knowledge on post glacial faults as an appendix.

Respect distances. Rationale and means of computation

International Nuclear Information System (INIS)

Munier, Raymond; Hoekmark, Harald

2004-12-01

Canisters with spent nuclear fuel can obviously not be located within deformation zones as this might jeopardise their long term mechanical stability and thereby constitute a potential hazard to the biosphere. Less apparent, but equally important, is the fact that earthquakes trigger reactivation, slip, of structures some distance from their hypocentres due to, among many other factors, stress redistribution. Fault slip across a deposition hole might damage the isolation capacity of the canister and thereby jeopardise the overall integrity of the barrier system. Therefore, the following question might be posed: What is the distance from a deformation zone beyond which a canister can be safely emplaced? This respect distance cannot be readily computed because, unknown future events aside, there are some complicated aspects that need to be addressed e.g. degree of conservatism, scale, our ability to model ice sheets and earthquakes, etc. In this report we discuss various aspects of the assignment of respect distances, propose a methodology for its assignment and apply the methodology to the Forsmark Site as a worked example. Our main concern, in the context discussed in this report, is the post glacial faults anticipated to occur after the next glaciations. To properly address conservativeness, analysis of risk, and its implementation in safety analysis, we provide an extensive compilation of our current knowledge on post glacial faults as an appendix

Determination of safety distance limits for a human near a cellular base station antenna, adopting the IEEE standard or ICNIRP guidelines.

Science.gov (United States)

Cooper, Justin; Marx, Bernd; Buhl, Johannes; Hombach, Volker

2002-09-01

This paper investigates the minimum distance for a human body in the near field of a cellular telephone base station antenna for which there is compliance with the IEEE or ICNIRP threshold values for radio frequency electromagnetic energy absorption in the human body. First, local maximum specific absorption rates (SARs), measured and averaged over volumes equivalent to 1 and to 10 g tissue within the trunk region of a physical, liquid filled shell phantom facing and irradiated by a typical GSM 900 base station antenna, were compared to corresponding calculated SAR values. The calculation used a homogeneous Visible Human body model in front of a simulated base station antenna of the same type. Both real and simulated base station antennas operated at 935 MHz. Antenna-body distances were between 1 and 65 cm. The agreement between measurements and calculations was excellent. This gave confidence in the subsequent calculated SAR values for the heterogeneous Visible Human model, for which each tissue was assigned the currently accepted values for permittivity and conductivity at 935 MHz. Calculated SAR values within the trunk of the body were found to be about double those for the homogeneous case. When the IEEE standard and the ICNIRP guidelines are both to be complied with, the local SAR averaged over 1 g tissue was found to be the determining parameter. Emitted power values from the antenna that produced the maximum SAR value over 1 g specified in the IEEE standard at the base station are less than those needed to reach the ICNIRP threshold specified for the local SAR averaged over 10 g. For the GSM base station antenna investigated here operating at 935 MHz with 40 W emitted power, the model indicates that the human body should not be closer to the antenna than 18 cm for controlled environment exposure, or about 95 cm for uncontrolled environment exposure. These safe distance limits are for SARs averaged over 1 g tissue. The corresponding safety distance limits

Safety analysis report for packaging (onsite) steel drum

International Nuclear Information System (INIS)

McCormick, W.A.

1998-01-01

This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum

The transport safety programme

International Nuclear Information System (INIS)

Selling, H.A.

1994-01-01

The transport safety programme is one of the smaller technical sub-programmes in the Radiation Safety Section of the Division of Nuclear Safety, in terms of both regular budget and professional staff allocations. The overall aim of the programme is to promote the safe movement of radioactive material worldwide. The specific objectives are the development, review and maintenance of the Regulations for the Safe Transport of Radioactive Material, Safety Series No 6, and its supporting documents Safety Series Nos 7, 37 and 80 and the assistance to Member States and International Organizations in the proper implementation of the Regulations. One of the important issues that emerged during an ongoing Review/Revision process is the transport of Low-Specific Activity (LSA) material and Surface Contaminated Objects (SCO). Many of the radioactive waste materials fall in one of these categories. The subject has gained substance because it is expected that in the next decade radioactive waste could become available in so far unprecedented quantities and volumes due to decontamination and decommissioning of nuclear facilities. (author)

Concept of ICRU's operational quantity and its application

International Nuclear Information System (INIS)

Murakami, Hiroyuki

1995-01-01

The operational quantity which was introduced in the ICRU report 39 published in 1985 was shocking rather than fresh for the author. The report was translated into Japanese, but at the beginning, the contents were not able to be understood. Thereafter, the measurement of ICRU sphere dose equivalent was introduced in a national law. But it is feared that the understanding of this operational quantity is limited to specialist level, and is not by men of practical works. The meaning of ''operational'' must be that workers measure and obtain dose on the spot for the radiation protection for themselves. The principles used when ICRU considered the new practical measured quantity are shown. In the definition of operational quantity in area monitoring, two concepts of expanded and aligned connect real measurement with the operational quantity. The problems of measuring individual dose equivalent are discussed. As to the reality of applying the operational quantity, the fundamentals of the calibration of measuring instruments, the investigation of the operational quantity in relation to measuring instruments and measurement mode, and the relation of area monitoring and individual monitoring are described. (K.I.)

Quantifying cannabis: A field study of marijuana quantity estimation.

Science.gov (United States)

Prince, Mark A; Conner, Bradley T; Pearson, Matthew R

2018-05-17

The assessment of marijuana use quantity poses unique challenges. These challenges have limited research efforts on quantity assessments. However, quantity estimates are critical to detecting associations between marijuana use and outcomes. We examined accuracy of marijuana users' estimations of quantities of marijuana they prepared to ingest and predictors of both how much was prepared for a single dose and the degree of (in)accuracy of participants' estimates. We recruited a sample of 128 regular-to-heavy marijuana users for a field study wherein they prepared and estimated quantities of marijuana flower in a joint or a bowl as well as marijuana concentrate using a dab tool. The vast majority of participants overestimated the quantity of marijuana that they used in their preparations. We failed to find robust predictors of estimation accuracy. Self-reported quantity estimates are inaccurate, which has implications for studying the link between quantity and marijuana use outcomes. (PsycINFO Database Record (c) 2018 APA, all rights reserved).

Validation, verification and evaluation of a Train to Train Distance Measurement System by means of Colored Petri Nets

International Nuclear Information System (INIS)

Song, Haifeng; Liu, Jieyu; Schnieder, Eckehard

2017-01-01

Validation, verification and evaluation are necessary processes to assure the safety and functionality of a system before its application in practice. This paper presents a Train to Train Distance Measurement System (TTDMS), which can provide distance information independently from existing onboard equipment. Afterwards, we proposed a new process using Colored Petri Nets to verify the TTDMS system functional safety, as well as to evaluate the system performance. Three main contributions are carried out in the paper: Firstly, this paper proposes a formalized TTDMS model, and the model correctness is validated using state space analysis and simulation-based verification. Secondly, corresponding checking queries are proposed for the purpose of functional safety verification. Further, the TTDMS performance is evaluated by applying parameters in the formal model. Thirdly, the reliability of a functional prototype TTDMS is estimated. It is found that the procedure can cooperate with the system development, and both formal and simulation-based verifications are performed. Using our process to evaluate and verify a system is easier to read and more reliable compared to executable code and mathematical methods. - Highlights: • A new Train to Train Distance Measurement System. • New approach verifying system functional safety and evaluating system performance by means of CPN. • System formalization using the system property concept. • Verification of system functional safety using state space analysis. • Evaluation of system performance applying simulation-based analysis.

30 CFR 75.325 - Air quantity.

Science.gov (United States)

2010-07-01

... the exposure of miners. (i) A ventilating air quantity that is less than what is required by paragraph... results of sampling that demonstrate that the lesser air quantity will maintain continuous compliance with applicable TLV ®'s. (j) If during sampling required by § 70.1900(c) of this subchapter the ventilating air is...

Dose rate constants for new dose quantities

International Nuclear Information System (INIS)

Tschurlovits, M.; Daverda, G.; Leitner, A.

1992-01-01

Conceptual changes and new quantities made is necessary to reassess dose rate quantities. Calculations of the dose rate constant were done for air kerma, ambient dose equivalent and directional dose equivalent. The number of radionuclides is more than 200. The threshold energy is selected as 20 keV for the dose equivalent constants. The dose rate constant for the photon equivalent dose as used mainly in German speaking countries as a temporary quantity is also included. (Author)

Criticality safety

International Nuclear Information System (INIS)

Walker, G.

1983-01-01

When a sufficient quantity of fissile material is brought together a self-sustaining neutron chain reaction will be started in it and will continue until some change occurs in the fissile material to stop the chain reaction. The quantity of fissile material required is the 'Critical Mass'. This is not a fixed quantity even for a given type of fissile material but varies between quite wide limits depending on a number of factors. In a nuclear reactor the critical mass of fissile material is assembled under well-defined condition to produce a controllable chain reaction. The same materials have to be handled outside the reactor in all stages of fuel element manufacture, storage, transport and irradiated fuel reprocessing. At any stage it is possible (at least in principle) to assemble a critical mass and thus initiate an accidental and uncontrollable chain reaction. Avoiding this is what criticality safety is all about. A system is just critical when the rate of production of neutrons balances the rate of loss either by escape or by absorption. The factors affecting criticality are, therefore, those which effect neutron production and loss. The principal ones are:- type of nuclide and enrichment (or isotopic composition), moderation, reflection, concentration (density), shape and interaction. Each factor is considered in detail. (author)

An optimization method for the distance between exits of buildings considering uncertainties based on arbitrary polynomial chaos expansion

NARCIS (Netherlands)

Xie, Qimiao; Wang, Jinhui; Lu, Shouxiang; Hensen, J.L.M.

2016-01-01

The distance between exits is an important design parameter in fire safety design of buildings. In order to find the optimal distance between exits under uncertainties with a low computational cost, the surrogate model (i.e. approximation model) of evacuation time is constructed by the arbitrary

Distance Education in Technological Age

Directory of Open Access Journals (Sweden)

R .C. SHARMA

2005-04-01

provides details on how the multi-media systems like radio, audio cassettes, telephone, video cassettes, video discs, education television and computer based education etc can be successfully adopted. There are factors like socio-political, economic, human and administrative, and economic, which manipulate the application of information communication technology in education in developing countries. The authors in their chapters on satellite communication and virtual university explain the advancements. The book also gives details of how the library services could be arranged for the distance learners in developing countries. Skills in distance teaching are crucial to the successful counseling and teaching as the learners have varied characteristics. These skills contribute to the effective distance teaching in traditional as well as online distance education settings. A major portion of the book has been dedicated to the e-learning and virtual university initiatives. Cases from YashwantRao Chawan Maharastra Open University, a project C-MODE which deals with offering education through virtual academy and application of non-broadcasting and broadcasting media technologies to distance education can be found in these chapters.Research in and research on distance education is very significant. Quality and Quantity of research in distance education has been a source of prime concern of educators. The readers can find here an overview of review and critiques of researches in the field of open and distance learning in the Indian context and what are various changing paradigms of research in distance education. The authors strongly suggest undertaking researches on pedagogy, educational media and management of distance education. The book contains useful information for the beginners in basic distance education and those who are interested in knowing what happened and what is happening in developing countries. Biodata and Adresses of Reviewer Ramesh Chandra Sharma holds a PhD in

7 CFR 61.102 - Determination of quantity index.

Science.gov (United States)

2010-01-01

... the quantity index shall equal four times percentage of oil plus six times percentage of ammonia, plus 5. (b) For American Pima cottonseed the quantity index shall equal four times percentage of oil... 7 Agriculture 3 2010-01-01 2010-01-01 false Determination of quantity index. 61.102 Section 61.102...

Distance-based microfluidic quantitative detection methods for point-of-care testing.

Science.gov (United States)

Tian, Tian; Li, Jiuxing; Song, Yanling; Zhou, Leiji; Zhu, Zhi; Yang, Chaoyong James

2016-04-07

Equipment-free devices with quantitative readout are of great significance to point-of-care testing (POCT), which provides real-time readout to users and is especially important in low-resource settings. Among various equipment-free approaches, distance-based visual quantitative detection methods rely on reading the visual signal length for corresponding target concentrations, thus eliminating the need for sophisticated instruments. The distance-based methods are low-cost, user-friendly and can be integrated into portable analytical devices. Moreover, such methods enable quantitative detection of various targets by the naked eye. In this review, we first introduce the concept and history of distance-based visual quantitative detection methods. Then, we summarize the main methods for translation of molecular signals to distance-based readout and discuss different microfluidic platforms (glass, PDMS, paper and thread) in terms of applications in biomedical diagnostics, food safety monitoring, and environmental analysis. Finally, the potential and future perspectives are discussed.

The Acquisition of Quantity Contrasts in Guina-ang Bontok

Science.gov (United States)

Aoyama, Katsura; Reid, Lawrence A.

2016-01-01

This study reports on the acquisition of quantity contrasts in Guina-ang Bontok, an indigenous language spoken in the Philippines. Four-year-old and 5-year-old children's perception and production of quantity contrasts were examined using a pair of names that contrast in the quantity of the medial nasal. Frequencies of the quantity contrast were…

Memory-Based Quantity Discrimination in Coyotes (Canis latrans

Directory of Open Access Journals (Sweden)

Salif Mahamane

2014-08-01

Full Text Available Previous research has shown that the ratio between competing quantities of food significantly mediates coyotes‘ (Canis latrans ability to choose the larger of two food options. These previous findings are consistent with predictions made by Weber‘s Law and indicate that coyotes possess quantity discrimination abilities that are similar to other species. Importantly, coyotes‘ discrimination abilities are similar to domestic dogs (Canis lupus familiaris, indicating that quantitative discrimination may remain stable throughout certain species‘ evolution. However, while previously shown in two domestic dogs, it is unknown whether coyotes possess the ability to discriminate visual quantities from memory. Here, we address this question by displaying different ratios of food quantities to 14 coyotes before placing the choices out of sight. The coyotes were then allowed to select one of either non-visible food quantities. Coyotes‘ discrimination of quantity from memory does not follow Weber‘s Law in this particular task. These results suggest that working memory in coyotes may not be adapted to maintain information regarding quantity as well as in domestic dogs. The likelihood of a coyote‘s choosing the large option increased when it was presented with difficult ratios of food options first, before it was later presented with trials using more easily discriminable ratios, and when the large option was placed on one particular side. This suggests that learning or motivation increased across trials when coyotes experienced difficult ratios first, and that location of food may have been more salient in working memory than quantity of food.

Quantities used in radiological protection

International Nuclear Information System (INIS)

Menossi, Carlos

2010-01-01

The application of ICRP recommendations requires knowledge of a variety of concepts and magnitudes. Many of them are employed in other fields of science and precision in its definition reflects this wide application. In this regard, information on quantities and basic units of radiation, which exists in numerous publications, are subjects of great interest. The characteristics and radiation effects are studied by physicists, biologists and chemists mainly. However, there are basics that must be known and to be recognized by general practitioners and specialists from all branches of medicine. The information on quantities and units are used only in radiation protection, have been obtained from the reports listed on the attached bibliography. Such quantities and units contain weighting factors used to provide for different types of radiation and energies that affect the body and thus take into account the relative radio-sensitivity of different tissues. Additionally, they have added a series of data for a better understanding of the units: for example, multiples and sub-multiples, and some examples of converting the units used in radiation protection. (author) [es

48 CFR 916.504 - Indefinite-quantity contracts.

Science.gov (United States)

2010-10-01

... indefinite-quantity, multiple award contracts to ensure that adequate consideration exists to contractually... contracts. 916.504 Section 916.504 Federal Acquisition Regulations System DEPARTMENT OF ENERGY CONTRACTING METHODS AND CONTRACT TYPES TYPES OF CONTRACTS Indefinite-Delivery Contracts 916.504 Indefinite-quantity...

The covariance matrix of derived quantities and their combination

International Nuclear Information System (INIS)

Zhao, Z.; Perey, F.G.

1992-06-01

The covariance matrix of quantities derived from measured data via nonlinear relations are only approximate since they are functions of the measured data taken as estimates for the true values of the measured quantities. The evaluation of such derived quantities entails new estimates for the true values of the measured quantities and consequently implies a modification of the covariance matrix of the derived quantities that was used in the evaluation process. Failure to recognize such an implication can lead to inconsistencies between the results of different evaluation strategies. In this report we show that an iterative procedure can eliminate such inconsistencies

Safety evaluation for packaging (onsite) SERF cask

International Nuclear Information System (INIS)

Edwards, W.S.

1997-01-01

This safety evaluation for packaging (SEP) documents the ability of the Special Environmental Radiometallurgy Facility (SERF) Cask to meet the requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for transfer of Type B quantities (up to highway route controlled quantities) of radioactive material within the 300 Area of the Hanford Site. This document shall be used to ensure that loading, tie down, transport, and unloading of the SERF Cask are performed in accordance with WHC-CM-2-14. This SEP is valid until October 1, 1999. After this date, an update or upgrade to this document is required

Environmental and safety issues of the fusion fuel cycle

International Nuclear Information System (INIS)

Crocker, J.G.

1980-01-01

This paper discusses the environmental and safety concerns inherent in the development of fusion energy, and the current Department of Energy programs seeking to: (1) develop safe and reliable techniques for tritium control; (2) reduce the quantity of activation products produced; and (3) provide designs to limit the potential for accidents that could result in release of radioactive materials. Because of the inherent safety features of fusion and the early start that has been made in safety problem recognition and solution, fusion should be among the lower risk technologies for generation of commercial power

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

1991-01-01

Jan 1, 1991 ... The research established that quantity surveyors regarded handing in their CPD ... Surveying, Walter Sisulu University, PO Box 1421, East London, 5200, South Africa. ... Keywords: Continuing professional development, quantity surveying, perception .... In spite of this opportunity enshrined in the Act, the.

PERBANDINGAN EUCLIDEAN DISTANCE DENGAN CANBERRA DISTANCE PADA FACE RECOGNITION

Directory of Open Access Journals (Sweden)

Sendhy Rachmat Wurdianarto

2014-08-01

Full Text Available Perkembangan ilmu pada dunia komputer sangatlah pesat. Salah satu yang menandai hal ini adalah ilmu komputer telah merambah pada dunia biometrik. Arti biometrik sendiri adalah karakter-karakter manusia yang dapat digunakan untuk membedakan antara orang yang satu dengan yang lainnya. Salah satu pemanfaatan karakter / organ tubuh pada setiap manusia yang digunakan untuk identifikasi (pengenalan adalah dengan memanfaatkan wajah. Dari permasalahan diatas dalam pengenalan lebih tentang aplikasi Matlab pada Face Recognation menggunakan metode Euclidean Distance dan Canberra Distance. Model pengembangan aplikasi yang digunakan adalah model waterfall. Model waterfall beriisi rangkaian aktivitas proses yang disajikan dalam proses analisa kebutuhan, desain menggunakan UML (Unified Modeling Language, inputan objek gambar diproses menggunakan Euclidean Distance dan Canberra Distance. Kesimpulan yang dapat ditarik adalah aplikasi face Recognation menggunakan metode euclidean Distance dan Canverra Distance terdapat kelebihan dan kekurangan masing-masing. Untuk kedepannya aplikasi tersebut dapat dikembangkan dengan menggunakan objek berupa video ataupun objek lainnya.   Kata kunci : Euclidean Distance, Face Recognition, Biometrik, Canberra Distance

Macro-level safety analysis of pedestrian crashes in Shanghai, China.

Science.gov (United States)

Wang, Xuesong; Yang, Junguang; Lee, Chris; Ji, Zhuoran; You, Shikai

2016-11-01

Pedestrian safety has become one of the most important issues in the field of traffic safety. This study aims at investigating the association between pedestrian crash frequency and various predictor variables including roadway, socio-economic, and land-use features. The relationships were modeled using the data from 263 Traffic Analysis Zones (TAZs) within the urban area of Shanghai - the largest city in China. Since spatial correlation exists among the zonal-level data, Bayesian Conditional Autoregressive (CAR) models with seven different spatial weight features (i.e. (a) 0-1 first order, adjacency-based, (b) common boundary-length-based, (c) geometric centroid-distance-based, (d) crash-weighted centroid-distance-based, (e) land use type, adjacency-based, (f) land use intensity, adjacency-based, and (g) geometric centroid-distance-order) were developed to characterize the spatial correlations among TAZs. Model results indicated that the geometric centroid-distance-order spatial weight feature, which was introduced in macro-level safety analysis for the first time, outperformed all the other spatial weight features. Population was used as the surrogate for pedestrian exposure, and had a positive effect on pedestrian crashes. Other significant factors included length of major arterials, length of minor arterials, road density, average intersection spacing, percentage of 3-legged intersections, and area of TAZ. Pedestrian crashes were higher in TAZs with medium land use intensity than in TAZs with low and high land use intensity. Thus, higher priority should be given to TAZs with medium land use intensity to improve pedestrian safety. Overall, these findings can help transportation planners and managers understand the characteristics of pedestrian crashes and improve pedestrian safety. Copyright © 2016 Elsevier Ltd. All rights reserved.

Railway automatic safety protection system based on GPS

Directory of Open Access Journals (Sweden)

Fu Hai Juan

2016-01-01

Full Text Available The automatic protection system of railway safety is designed for the railway construction workers to protect alarm, and the safety protection device by using GPS satellite positioning system to acquire location information of the operating point, through the CTC/TDCS system and computer monitoring system for the running of the train position and the arithmetic distance. Achieving timely and continuously forecasts about the distance of the train which is apart from the operating point to prompt the voice alarm of the approaching train. Using digital technology to realize the function of the traditional analog interphone, eliminates the quality problems of the call. With the GSM-R, mobile wireless transmission channel and terminal technology, it overcomes the restrictions of the analog interphone which influenced by communication distance and more problems of blind areas. Finally to achieve practical, convenient, applicable and adaptable design goals.

Aviation Safety Simulation Model

Science.gov (United States)

Houser, Scott; Yackovetsky, Robert (Technical Monitor)

2001-01-01

The Aviation Safety Simulation Model is a software tool that enables users to configure a terrain, a flight path, and an aircraft and simulate the aircraft's flight along the path. The simulation monitors the aircraft's proximity to terrain obstructions, and reports when the aircraft violates accepted minimum distances from an obstruction. This model design facilitates future enhancements to address other flight safety issues, particularly air and runway traffic scenarios. This report shows the user how to build a simulation scenario and run it. It also explains the model's output.

Urban gas drilling and distance ordinances in the Texas Barnett Shale

International Nuclear Information System (INIS)

Fry, Matthew

2013-01-01

Newly accessible shale deposits and other unconventional sources of natural gas have dramatically increased global gas reserves and are regarded as major future energy sources. Shale gas drilling began in Texas and is expanding throughout the U.S. and globally. In Texas and other regions, large population centers overlie these deposits. As a result, city residents increasingly come into contact with extraction activities. The proximity of drilling activities to residential areas raises a number of concerns, including noise, dust and emissions hazards, public safety, diminished quality of life, and effects on neighborhood aesthetics and property values. Cities in Texas address these concerns through setback ordinances that regulate the distance between gas wells and residences, schools, floodplains, etc. Although the state of Texas permits drilling 200 ft (61 m) from residences, many municipalities in the Dallas–Fort Worth Metroplex (DFW) have established longer setback distances. This paper analyzes the purpose and basis for setback distances among 26 municipalities in DFW. Findings show that there is no uniform setback distance, distances have increased over time, and, rather than technically-based, setbacks are political compromises. For policy makers confronted with urban shale gas drilling, deriving setback distances from advanced emissions monitoring could decrease setback distance ambiguity. -- Highlights: •Urban shale gas drilling is expanding across the globe. •Municipal distance regulations address many concerns associated with urban drilling. •In Texas, setbacks have no empirical basis, but are political compromises. •Advanced monitoring methods could be used to standardize setback distances

Ferrocyanide Safety Program: Data requirements for the ferrocyanide safety issue developed through the data quality objectives (DQO) process

International Nuclear Information System (INIS)

Buck, J.W.; Anderson, C.M.; Pulsipher, B.A.; Toth, J.J.; Turner, P.J.; Cash, R.J.; Dukelow, G.T.; Meacham, J.E.

1993-12-01

This document records the data quality objectives (DQO) process applied to the Ferrocyanide Waste Tank Safety Issue at the Hanford Site by the Pacific Northwest Laboratory and Westinghouse Hanford Company. Specifically, the major recommendations and findings from this Ferrocyanide DQO process are presented so that decision makers can determine the type, quantity, and quality of data required for addressing tank safety issues. The decision logic diagrams and error tolerance equations also are provided. Finally, the document includes the DQO sample-size formulas for determining specific tank sampling requirements

Continuing Professional Development in the quantity surveying ...

African Journals Online (AJOL)

This research study was conducted in order to investigate Continuing Professional Development (CPD) in the South African quantity surveying profession. The study further aimed to establish the reasons why some quantity surveyors do not acquire the required CPD hours and face losing their professional registration with ...

Experience in nuclear engineering distance education at the University of Tennessee

International Nuclear Information System (INIS)

Dodds, H.L.

2011-01-01

This paper describes the distance education programs in nuclear engineering at The University of Tennessee (UT), which includes several courses that are of interest to the mathematics and computation community such as reactor theory and design, shielding, statistics, health physics, and criticality safety. All of the courses needed for the MS degree in nuclear engineering and several of the courses needed for the PhD degree in nuclear engineering are delivered synchronously (i.e., interactive in real time) via the Internet to students located anywhere by instructors located anywhere. The paper will also describe the historical development of distance education programs at UT as well as the benefits of the programs to students and to the university. The oral presentation associated with this paper will include a short movie that demonstrates the technology used for distance delivery. (author)

Hypergraph topological quantities for tagged social networks

Science.gov (United States)

Zlatić, Vinko; Ghoshal, Gourab; Caldarelli, Guido

2009-09-01

Recent years have witnessed the emergence of a new class of social networks, which require us to move beyond previously employed representations of complex graph structures. A notable example is that of the folksonomy, an online process where users collaboratively employ tags to resources to impart structure to an otherwise undifferentiated database. In a recent paper, we proposed a mathematical model that represents these structures as tripartite hypergraphs and defined basic topological quantities of interest. In this paper, we extend our model by defining additional quantities such as edge distributions, vertex similarity and correlations as well as clustering. We then empirically measure these quantities on two real life folksonomies, the popular online photo sharing site Flickr and the bookmarking site CiteULike. We find that these systems share similar qualitative features with the majority of complex networks that have been previously studied. We propose that the quantities and methodology described here can be used as a standard tool in measuring the structure of tagged networks.

Safety sans Frontières: An International Safety Culture Model.

Science.gov (United States)

Reader, Tom W; Noort, Mark C; Shorrock, Steven; Kirwan, Barry

2015-05-01

The management of safety culture in international and culturally diverse organizations is a concern for many high-risk industries. Yet, research has primarily developed models of safety culture within Western countries, and there is a need to extend investigations of safety culture to global environments. We examined (i) whether safety culture can be reliably measured within a single industry operating across different cultural environments, and (ii) if there is an association between safety culture and national culture. The psychometric properties of a safety culture model developed for the air traffic management (ATM) industry were examined in 17 European countries from four culturally distinct regions of Europe (North, East, South, West). Participants were ATM operational staff (n = 5,176) and management staff (n = 1,230). Through employing multigroup confirmatory factor analysis, good psychometric properties of the model were established. This demonstrates, for the first time, that when safety culture models are tailored to a specific industry, they can operate consistently across national boundaries and occupational groups. Additionally, safety culture scores at both regional and national levels were associated with country-level data on Hofstede's five national culture dimensions (collectivism, power distance, uncertainty avoidance, masculinity, and long-term orientation). MANOVAs indicated safety culture to be most positive in Northern Europe, less so in Western and Eastern Europe, and least positive in Southern Europe. This indicates that national cultural traits may influence the development of organizational safety culture, with significant implications for safety culture theory and practice. © 2015 Society for Risk Analysis.

Environmental Assessment of Demolition Activities at Dover Air Force Base, Delaware

Science.gov (United States)

2003-11-01

Setophaga ruticilla), broad- winged hawk (Buteo platypterus), cliff swallow (Petrochelidon pyrrhonota), bank swallow ( Riparia riparia ), black vulture...Explosive safety-quantity distance (QD) zones are designated areas designed to safeguard the base population and civilian community from potential...explosions. These clear zones include the area within a safety arc surrounding an explosive storage facility. The QD zones at Dover AFB encompass

Remarks and suggestions concerned with formulation of the definition of quantity ''committed dose'' and quantity ''radiation burden'' useful in estimates of population exposure

International Nuclear Information System (INIS)

Cwik, T.

1990-01-01

The paper contains remarks to the definitions of the quantity ''commited dose'' given in the publications of the ICRP. The suggestions are presented on the mode of formulating the definition of the quantity ''commited dose'' and the definition of the quantity denoted hitherto by the symbol H 50 . The other suggestions deal with introduction of the quantity ''radiation burden'', assigned for use in assessments of irradiation expressed ''per caput'' of population. 9 refs. (author)

Encyclopedia of distances

CERN Document Server

Deza, Michel Marie

2016-01-01

This 4th edition of the leading reference volume on distance metrics is characterized by updated and rewritten sections on some items suggested by experts and readers, as well a general streamlining of content and the addition of essential new topics. Though the structure remains unchanged, the new edition also explores recent advances in the use of distances and metrics for e.g. generalized distances, probability theory, graph theory, coding theory, data analysis. New topics in the purely mathematical sections include e.g. the Vitanyi multiset-metric, algebraic point-conic distance, triangular ratio metric, Rossi-Hamming metric, Taneja distance, spectral semimetric between graphs, channel metrization, and Maryland bridge distance. The multidisciplinary sections have also been supplemented with new topics, including: dynamic time wrapping distance, memory distance, allometry, atmospheric depth, elliptic orbit distance, VLBI distance measurements, the astronomical system of units, and walkability distance. Lea...

Distance Learning

National Research Council Canada - National Science Library

Braddock, Joseph

1997-01-01

A study reviewing the existing Army Distance Learning Plan (ADLP) and current Distance Learning practices, with a focus on the Army's training and educational challenges and the benefits of applying Distance Learning techniques...

Control Analysis Of Tobacco Raw Material Supplies Using Eoq Method Economic Order Quantity To Reach Efficiency Total Costs Of Raw Material In Pr. Sukun

Directory of Open Access Journals (Sweden)

Wiwik Sudarwati

2017-07-01

Full Text Available The raw material inventory control system determines and guarantees the availability of raw material stock in the right quantity quality and timing. The problem in this research is the procurement of raw materials of tobacco. PR. Sukun still often experiences the excess. This is related to the frequency of raw material purchases and the quantity of raw material purchases which can lead to waste of working capital embedded in raw material inventory raw material ordering costs and raw material storage costs. The purpose of this research is to know how to make an efficiency level in procurement of raw material inventory between EOQ method compared with policy of PR. Sukun. The type of research used is analytic descriptive type. Data analysis begins by analyzing raw material quantity comparison total raw material inventory cost and raw material cost between PR Sukun policy with EOQ method. Based on the results of research known that by using EOQ method can be much more efficient compared to policy of PR. Sukun. The quantity and frequency of purchasing raw materials is less but still take into account the safety stock and reorder point so the production process is not disturbed. In addition the cost of purchasing ordering costs and raw materials storage costs less so as to create efficiencies on the cost of raw materials inventory. PR. Sukun in the procurement of raw material inventory should use EOQ method to be more efficient and take into account the safety stock and reorder point to avoid the inventory excess of raw materials.

41 CFR 101-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... MANAGEMENT 27.1-Stock Replenishment § 101-27.102 Economic order quantity principle. The economic order quantity (EOQ) principle is a means for achieving economical inventory management. Application of the EOQ... 41 Public Contracts and Property Management 2 2010-07-01 2010-07-01 true Economic order quantity...

REPRESENTATIONS OF DISTANCE: DIFFERENCES IN UNDERSTANDING DISTANCE ACCORDING TO TRAVEL METHOD

Directory of Open Access Journals (Sweden)

Gunvor Riber Larsen

2017-12-01

Full Text Available This paper explores how Danish tourists represent distance in relation to their holiday mobility and how these representations of distance are a result of being aero-mobile as opposed to being land-mobile. Based on interviews with Danish tourists, whose holiday mobility ranges from the European continent to global destinations, the first part of this qualitative study identifies three categories of representations of distance that show how distance is being ‘translated’ by the tourists into non-geometric forms: distance as resources, distance as accessibility, and distance as knowledge. The representations of distance articulated by the Danish tourists show that distance is often not viewed in ‘just’ kilometres. Rather, it is understood in forms that express how transcending the physical distance through holiday mobility is dependent on individual social and economic contexts, and on whether the journey was undertaken by air or land. The analysis also shows that being aeromobile is the holiday transportation mode that removes the tourists the furthest away from physical distance, resulting in the distance travelled by air being represented in ways that have the least correlation, in the tourists’ minds, with physical distance measured in kilometres.

Quantities of uranium-235 buried in disposal boxes, 1985--1991

International Nuclear Information System (INIS)

Cook, J.R.

1991-01-01

IWT was asked by J. R. Schornhorst of NPSR to determine the distribution of the quantity of enriched uranium per disposal box (B-25) of the years 1985--1991 to provide input to an uptake of the E Area Safety Analysis. This information was considered important since the issue of criticality is an important concern in safety analyses. Information found in the COBRA data base shows no disposal containers exceeded 100 grams of U-235. The COBRA data base was queried in a two-step process. First a short program in the NATURAL language was used to retrieve all records beginning with January 1983 having a Burial Code of less than 4, indicating low-level waste disposed in trenches. These records were then passed to a temporary storage file and read into a program written in Statistical Analysis System (SAS) language. SAS was used to eliminate waste from the Naval Fuel Facility, which will not operate in the future, and to sort the records in order of increasing amounts of U-235. The SAS procedure FREQ was then used to produce a cumulative frequency distribution of grams of U-235. A total of 53,198 packages were disposed of during this time period, 277 of which contained U-235. The programs used and resulting output are attached as Appendix I

Relevance of protection quantities in medical exposures

International Nuclear Information System (INIS)

Pradhan, A.S.

2008-01-01

International Commission on Radiological Protection (ICRP) continues to classify the exposures to radiation in three categories; namely 1- occupational exposure, 2- public exposure, and 3- medical exposure. Protection quantities are primarily meant for the regulatory purpose in radiological protection for controlling and limiting stochastic risks in occupational and public exposures. These are based on two basic assumptions of 1- linear no-threshold dose-effect relationship (LNT) at low doses and 2- long-term additivity of low doses. Medical exposure are predominantly delivered to individuals (patients) undergoing diagnostic examinations, interventional procedures and radiation therapy but also include individual caring for or comforting patients incurring exposure and the volunteers of biomedical medical research programmes. Radiation protection is as relevant to occupational and public exposure as to medical exposures except that the dose limits set for the formers are not applicable to medical exposure but reference levels and dose constrains are recommended for diagnostic and interventional medical procedures. In medical institutions, both the occupational and medical exposure takes place. Since the doses in diagnostic examinations are low, it has been observed that not only the protection quantities are often used in such cases but these are extended to estimate the number of cancer deaths due to such practices. One of the striking features of the new ICRP recommendations has been to elaborate the concepts of the dosimetric quantities. The limitation of protection quantities ((Effective dose, E=Σ RT D TR .W T .W R and Equivalent Dose H T =Σ RT D TR .W R ) have been brought out and this has raised a great concern and initiated debates on the use of these quantities in medical exposures. Consequently, ICRP has set a task group to provide more details and the recommendations. It has, therefore, became important to draw the attention of medical physics community

DOE approach to threshold quantities

International Nuclear Information System (INIS)

Wickham, L.E.; Kluk, A.F.; Department of Energy, Washington, DC)

1985-01-01

The Department of Energy (DOE) is developing the concept of threshold quantities for use in determining which waste materials must be handled as radioactive waste and which may be disposed of as nonradioactive waste at its sites. Waste above this concentration level would be managed as radioactive or mixed waste (if hazardous chemicals are present); waste below this level would be handled as sanitary waste. Ideally, the threshold must be set high enough to significantly reduce the amount of waste requiring special handling. It must also be low enough so that waste at the threshold quantity poses a very small health risk and multiple exposures to such waste would still constitute a small health risk. It should also be practical to segregate waste above or below the threshold quantity using available instrumentation. Guidance is being prepared to aid DOE sites in establishing threshold quantity values based on pathways analysis using site-specific parameters (waste stream characteristics, maximum exposed individual, population considerations, and site specific parameters such as rainfall, etc.). A guidance dose of between 0.001 to 1.0 mSv/y (0.1 to 100 mrem/y) was recommended with 0.3 mSv/y (30 mrem/y) selected as the guidance dose upon which to base calculations. Several tasks were identified, beginning with the selection of a suitable pathway model for relating dose to the concentration of radioactivity in the waste. Threshold concentrations corresponding to the guidance dose were determined for waste disposal sites at a selected humid and arid site. Finally, cost-benefit considerations at the example sites were addressed. The results of the various tasks are summarized and the relationship of this effort with related developments at other agencies discussed

Physical quantities, their role and treatment in gasflow measurement techniques

International Nuclear Information System (INIS)

Narjes, L.

1977-06-01

We begin by taking a closer look at the concepts physical quantity, dimension and unit of measurement. Then a survey is given of the physical quantities applied in gasflow measurement techniques. Here the volume-, as well as the mass-flow rate, as derived quantities are of particular interest. The application of these quantities in relation to the legal units of measurement is specifically described. In addition the quantity equation and further the quantity equation adapted to the use of suitable units and their modes of application are compared. In the appendix four examples clarify these modes. Special attention is paid to the quantity equation adapted to practically oriented units. The applications of this type of equation in VDI regulations, standards and other technical guidelines for measurement of flow are mentioned. Moreover, the meaning of the standard state for the comparison of flows of gaseous fluids is illustrated. The difficulties concerning an international agreement on uniform standard temperature are explained. Starting from there, the advantages of the fundamental quantity 'amount of substance' applied to the measurement of flow are described. The use of this quantity for the thermodynamic state of ideal and real gases, respectively gas mixtures, is demonstrated in the appendix by an example. (orig.) [de

The safety assessment of radioactive material transpotation at sea

International Nuclear Information System (INIS)

Satoh, K.; Ozaki, S.; Watabe, N.; Fukuda, S.; Iida, T.; Miyao, S.; Noguchi, K.; Nakajima, K.

1989-01-01

Large quantities of low level wastes are prepared for transportation by special use vessels from each power plant to the storage facility at Rokkasho-mura in Aomori Prefecture. Large quantities of reprocessed wastes are also planned for return by similar vessels to the same place from France and the UK. In this paper the authors describe the safety assessment in hypothetical accident conditions during such mass transportation at sea. Although the possibilities of the sinking of the special use vessels as shown in figure 1 are considered to be very low on account of their double-hull structure, it is necessary to estimate the radiological risks of the transportation in order to obtain public acceptance. In this study, the following procedure is taken: (i) assumption of accident; (ii) establishment of safety assessment procedure; (iii) determination of source terms; (iv) diffusion calculation of radionuclide; (v) estimation of radiation exposure of the public

Distance factor on reducing scattered radiation risk during interventional fluoroscopy

International Nuclear Information System (INIS)

Husaini Salleh; Mohd Khalid Matori; Muhammad Jamal Mat Isa; Zainal Jamaluddin; Mohd Firdaus Abdul Rahman; Mohd Khairusalih Mohd Zin

2012-01-01

Interventional Radiology (IR) is subspecialty of diagnostic radiology where minimally invasive procedures are performed using an x-ray as a guidance. This procedure can deliver high radiation doses to patient and medical staff compared with other radiological method due to long screening time. The use of proper shielding, shorten the exposure time and keep the distance are the practices to reduce scattered radiation risks to staff involve in this procedure. This project is to study the distance factor on reducing the scattered radiation effect to the medical staff. It also may provide the useful information which can be use to establish the scattered radiation profile during the IR for the sake of radiation protection and safety to the medical staff involved. (author)

Safety Test Program Summary SNAP 19 Pioneer Heat Source Safety Program

Energy Technology Data Exchange (ETDEWEB)

None,

1971-07-01

Sixteen heat source assemblies have been tested in support of the SNAP 19 Pioneer Safety Test Program. Seven were subjected to simulated reentry heating in various plasma arc facilities followed by impact on earth or granite. Six assemblies were tested under abort accident conditions of overpressure, shrapnel impact, and solid and liquid propellant fires. Three capsules were hot impacted under Transit capsule impact conditions to verify comparability of test results between the two similar capsule designs, thus utilizing both Pioneer and Transit Safety Test results to support the Safety Analysis Report for Pioneer. The tests have shown the fuel is contained under all nominal accident environments with the exception of minor capsule cracks under severe impact and solid fire environments. No catastrophic capsule failures occurred in this test which would release large quantities of fuel. In no test was fuel visible to the eye following impact or fire. Breached capsules were defined as those which exhibit thoria contamination on its surface following a test, or one which exhibited visible cracks in the post test metallographic analyses.

Engineering Solutions to Enhance Traffic Safety Performance on Two-Lane Highways

Directory of Open Access Journals (Sweden)

Lina Wu

2015-01-01

Full Text Available Improving two-lane highway traffic safety conditions is of practical importance to the traffic system, which has attracted significant research attention within the last decade. Many cost-effective and proactive solutions such as low-cost treatments and roadway safety monitoring programs have been developed to enhance traffic safety performance under prevailing conditions. This study presents research perspectives achieved from the Highway Safety Enhancement Project (HSEP that assessed safety performance on two-lane highways in Beijing, China. Potential causal factors are identified based on proposed evaluation criteria, and primary countermeasures are developed against inferior driving conditions such as sharp curves, heavy gradients, continuous downgrades, poor sight distance, and poor clear zones. Six cost-effective engineering solutions were specifically implemented to improve two-lane highway safety conditions, including (1 traffic sign replacement, (2 repainting pavement markings, (3 roadside barrier installation, (4 intersection channelization, (5 drainage optimization, and (6 sight distance improvement. The effectiveness of these solutions was examined and evaluated based on Empirical Bayes (EB models. The results indicate that the proposed engineering solutions effectively improved traffic safety performance by significantly reducing crash occurrence risks and crash severities.

Discounting of quantity surveying fees in South Africa

African Journals Online (AJOL)

by clients have forced Quantity Surveying firms into competition with ... Furthermore, 43% of consulting engineering firms were discounting their fees at a rate of .... Quantity. Surveying services are also offered in the fields of dispute resolution,.

Encyclopedia of distances

CERN Document Server

Deza, Michel Marie

2014-01-01

This updated and revised third edition of the leading reference volume on distance metrics includes new items from very active research areas in the use of distances and metrics such as geometry, graph theory, probability theory and analysis. Among the new topics included are, for example, polyhedral metric space, nearness matrix problems, distances between belief assignments, distance-related animal settings, diamond-cutting distances, natural units of length, Heidegger’s de-severance distance, and brain distances. The publication of this volume coincides with intensifying research efforts into metric spaces and especially distance design for applications. Accurate metrics have become a crucial goal in computational biology, image analysis, speech recognition and information retrieval. Leaving aside the practical questions that arise during the selection of a ‘good’ distance function, this work focuses on providing the research community with an invaluable comprehensive listing of the main available di...

New quantities in radiation protection and conversion coefficients

International Nuclear Information System (INIS)

1986-01-01

Four new quantities have been proposed by the ICRP for use in radiation protection from external sources, i.e. the ambient dose equivalent, the directional dose equivalent, the individual dose equivalent (penetrating), and the individual dose equivalent (superficial). These quantities are briefly described together with two new concepts of expanded and aligned fields. The BCRU recommends that these quantities should be adopted for use in the UK together with conversion coefficients when re-calibrating existing instruments, reporting the results of measurements and designing instruments. (UK)

The effect of terrain slope on firefighter safety zone effectiveness

Science.gov (United States)

Bret Butler; J. Forthofer; K. Shannon; D. Jimenez; D. Frankman

2010-01-01

The current safety zone guidelines used in the US were developed based on the assumption that the fire and safety zone were located on flat terrain. The minimum safe distance for a firefighter to be from a flame was calculated as that corresponding to a radiant incident energy flux level of 7.0kW-m-2. Current firefighter safety guidelines are based on the assumption...

A conserved quantity in thin body dynamics

International Nuclear Information System (INIS)

Hanna, J.A.; Pendar, H.

2016-01-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

A conserved quantity in thin body dynamics

Energy Technology Data Exchange (ETDEWEB)

Hanna, J.A., E-mail: hannaj@vt.edu [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Department of Physics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States); Pendar, H. [Department of Biomedical Engineering and Mechanics, Virginia Polytechnic Institute and State University, Blacksburg, VA 24061 (United States)

2016-02-15

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant. - Highlights: • A conserved quantity relevant to the dynamical equilibria of thin structures. • A mixed Lagrangian–Eulerian non-material action principle for fixed windows of axially moving systems. • Analytical solutions for rotating, flowing strings (yarn balloons). • Noether meets Bernoulli in a textile factory.

The ICRU dose equivalence quantities in radiation protection

International Nuclear Information System (INIS)

Grimbergen, T.W.M.

1990-09-01

The definitions and application of the new ICRU radiation protection quantities have been reviewed and studied in literature. Special emphasis was laid on the consequences of the use of the new quantities by personnel dosimetry services, and on the consequences of the use of the new quantities during an intercomparison programme for dosimetry services. The study shows that the recommendations of the ICRU are not yet complete and not fully realizable. This means that the dosimetry services always have to make certain approximations, when they use the new quantities. In literature, several approaches have been proposed. The feasibility of an approach depends on the characteristics of the dosimeters used. The use of different approaches by the dosimetry services is thought to be of possible influence on the results of an intercomparison programme. (author). 42 refs.; 3 figs.; 1 tab

The safety valve and climate policy

International Nuclear Information System (INIS)

Jacoby, Henry D.; Ellerman, A.D.

2004-01-01

The 'safety valve' is a possible addition to a cap-and-trade system of emissions regulation whereby the authority offers to sell permits in unlimited amount at a pre-set price. In this way the cost of meeting the cap can be limited. It was proposed in the US as a way to control perceived high costs of the Kyoto Protocol, and possibly as a way to shift the focus of policy from the quantity targets of the Protocol to emissions price. In international discussions, the idea emerged as a proposal for a compliance penalty. The usefulness of the safety valve depends on the conditions under which it might be introduced. For a time it might tame an overly stringent emissions target. It also can help control the price volatility during the introduction of gradually tightening one, although permit banking can ultimately serve the same function. It is unlikely to serve as a long-term feature of a cap-and-trade system, however, because of the complexity of coordinating price and quantity instruments and because it will interfere with the development of systems of international emissions trade

Foreign materials in the repository - update of estimated quantities

International Nuclear Information System (INIS)

Hagros, A.

2007-03-01

In a repository for spent nuclear fuel, a variety of materials are used during the construction process and during the operation of the repository. In addition to materials necessary for the construction and operation, some materials may be transported into the repository through the ventilation air, as emissions from vehicles, as waste produced by the staff etc. Both of these two types of materials are considered here and their quantities - both the introduced quantities and the quantities that remain after closure - in the repository constructed at Olkiluoto in Eurajoki, Finland are estimated here based on new information. This work is intended to update the estimations that have been made previously, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility ONKALO at Olkiluoto. During this construction process, the quantities of the different construction materials introduced into the underground openings have been monitored and they form a basis for estimating the quantities to be used in the future. The estimations made in this report are specific to a KBS-3V type repository and to the Olkiluoto site, although in some cases more generic information has been used, particularly when the relevant quantities have not been monitored in the ONKALO. The estimations are based on the new repository layout produced in 2006 and consider the latest plans for grouting and rock support. As these plans are generally not final yet, several different alternative plans are assumed when necessary. Also two different strategies for the backfilling of the tunnels are considered. The most significant differences with respect to the results of an earlier estimation are related to the materials used in grouting, shotcreting and in support bolts. In the cases where a mixture of bentonite and crushed rock is the used backfill alternative, gypsum and cement are the materials with the largest quantities remaining in the

Quantities of natural gas transmitted in January-December 2012. Quantities of natural gas transported in January-December 2012

International Nuclear Information System (INIS)

2013-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2012: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Interface Simulation Distances

Directory of Open Access Journals (Sweden)

Pavol Černý

2012-10-01

Full Text Available The classical (boolean notion of refinement for behavioral interfaces of system components is the alternating refinement preorder. In this paper, we define a distance for interfaces, called interface simulation distance. It makes the alternating refinement preorder quantitative by, intuitively, tolerating errors (while counting them in the alternating simulation game. We show that the interface simulation distance satisfies the triangle inequality, that the distance between two interfaces does not increase under parallel composition with a third interface, and that the distance between two interfaces can be bounded from above and below by distances between abstractions of the two interfaces. We illustrate the framework, and the properties of the distances under composition of interfaces, with two case studies.

An OSHA based approach to safety analysis for nonradiological hazardous materials

International Nuclear Information System (INIS)

Yurconic, M.

1992-08-01

The PNL method for chemical hazard classification defines major hazards by means of a list of hazardous substances (or chemical groups) with associated trigger quantities. In addition, the functional characteristics of the facility being classified is also be factored into the classification. In this way, installations defined as major hazard will only be those which have the potential for causing very serious incidents both on and off site. Because of the diversity of operations involving chemicals, it may not be possible to restrict major hazard facilities to certain types of operations. However, this hazard classification method recognizes that in the industrial sector major hazards are most commonly associated with activities involving very large quantities of chemicals and inherently energetic processes. These include operations like petrochemical plants, chemical production, LPG storage, explosives manufacturing, and facilities which use chlorine, ammonia, or other highly toxic gases in bulk quantities. The basis for this methodology is derived from concepts used by OSHA in its proposed chemical process safety standard, the Dow Fire and Explosion Index Hazard Classification Guide, and the International Labor Office's program on chemical safety. For the purpose of identifying major hazard facilities, this method uses two sorting criteria, (1) facility function and processes and (2) quantity of substances to identify facilities requiringclassification. Then, a measure of chemical energy potential (material factor) is used to identify high hazard class facilities

78 FR 31415 - Safety Zone; USA Triathlon; Milwaukee Harbor, Milwaukee, WI

Science.gov (United States)

2013-05-24

... minimal impact on the economy, will not interfere with other agencies, will not adversely alter the budget... due to the 2013 and 2014 Olympic and Sprint Distance National Championships. This safety zone is... Olympic and Sprint Distance National Championships. DATES: This final rule is effective from August 1...

The Impact of Seafarers’ Perceptions of National Culture and Leadership on Safety Attitude and Safety Behavior in Dry Bulk Shipping

Directory of Open Access Journals (Sweden)

Chin-Shan Lu

2016-06-01

Full Text Available This research aims to examine the effects of national culture and leadership style on safety performance in bulk shipping companies. Survey data collected from 322 respondents working in dry bulk carriers was used, a multiple regression analysis was conducted to analyze the influence of national culture and leadership styles (i.e. transformational, passive management, and contingent reward on safety attitude and safety behavior. The results indicate that national culture dimensions such as power distance, uncertainty avoidance, collectivism, and long-term orientation had a positive influence on safety behaviour. Long-term orientation had a positive influence on safety attitude, whereas masculinity had a negative influence on safety attitude of seafarers. Specifically, this research found that transformational leadership had a positive influence on safety attitude and safety behaviour of seafarers. Moreover, practical implication from the research findings to improve ship safety in dry bulk shipping were discussed.

Safety analysis report for packaging (onsite) multicanister overpack cask

International Nuclear Information System (INIS)

Edwards, W.S.

1997-01-01

This safety analysis report for packaging (SARP) documents the safety of shipments of irradiated fuel elements in the MUlticanister Overpack (MCO) and MCO Cask for a highway route controlled quantity, Type B fissile package. This SARP evaluates the package during transfers of (1) water-filled MCOs from the K Basins to the Cold Vacuum Drying Facility (CVDF) and (2) sealed and cold vacuum dried MCOs from the CVDF in the 100 K Area to the Canister Storage Building in the 200 East Area

Safety analysis report for packaging (onsite) multicanister overpack cask

Energy Technology Data Exchange (ETDEWEB)

Edwards, W.S.

1997-07-14

This safety analysis report for packaging (SARP) documents the safety of shipments of irradiated fuel elements in the MUlticanister Overpack (MCO) and MCO Cask for a highway route controlled quantity, Type B fissile package. This SARP evaluates the package during transfers of (1) water-filled MCOs from the K Basins to the Cold Vacuum Drying Facility (CVDF) and (2) sealed and cold vacuum dried MCOs from the CVDF in the 100 K Area to the Canister Storage Building in the 200 East Area.

Assessment of impact distances for particulate matter dispersion: A stochastic approach

Energy Technology Data Exchange (ETDEWEB)

Godoy, S.M.; Mores, P.L.; Santa Cruz, A.S.M. [CAIMI - Centro de Aplicaciones Informaticas y Modelado en Ingenieria, Universidad Tecnologica Nacional-Facultad Regional Rosario, Zeballos 1341-S2000 BQA Rosario, Santa Fe (Argentina); Scenna, N.J. [CAIMI - Centro de Aplicaciones Informaticas y Modelado en Ingenieria, Universidad Tecnologica Nacional-Facultad Regional Rosario, Zeballos 1341-S2000 BQA Rosario, Santa Fe (Argentina); INGAR - Instituto de Desarrollo y Diseno (Fundacion ARCIEN - CONICET), Avellaneda 3657, S3002 GJC Santa Fe (Argentina)], E-mail: nscenna@santafe-conicet.gov.ar

2009-10-15

It is known that pollutants can be dispersed from the emission sources by the wind, or settled on the ground. Particle size, stack height, topography and meteorological conditions strongly affect particulate matter (PM) dispersion. In this work, an impact distance calculation methodology considering different particulate sizes is presented. A Gaussian-type dispersion model for PM that handles size particles larger than 0.1 {mu}m is used. The model considers primary particles and continuous emissions. PM concentration distribution at every affected geographical point defined by a grid is computed. Stochastic uncertainty caused by the natural variability of atmospheric parameters is taken into consideration in the dispersion model by applying a Monte Carlo methodology. The prototype package (STRRAP) that takes into account the stochastic behaviour of atmospheric variables, developed for risk assessment and safe distances calculation [Godoy SM, Santa Cruz ASM, Scenna NJ. STRRAP SYSTEM - A software for hazardous materials risk assessment and safe distances calculation. Reliability Engineering and System Safety 2007;92(7):847-57] is enlarged for the analysis of the PM air dispersion. STRRAP computes distances from the source to every affected receptor in each trial and generates the impact distance distribution for each particulate size. In addition, a representative impact distance value to delimit the affected area can be obtained. Fuel oil stack effluents dispersion in Rosario city is simulated as a case study. Mass concentration distributions and impact distances are computed for the range of interest in environmental air quality evaluations (PM{sub 2.5}-PM{sub 10})

Assessment of impact distances for particulate matter dispersion: A stochastic approach

International Nuclear Information System (INIS)

Godoy, S.M.; Mores, P.L.; Santa Cruz, A.S.M.; Scenna, N.J.

2009-01-01

It is known that pollutants can be dispersed from the emission sources by the wind, or settled on the ground. Particle size, stack height, topography and meteorological conditions strongly affect particulate matter (PM) dispersion. In this work, an impact distance calculation methodology considering different particulate sizes is presented. A Gaussian-type dispersion model for PM that handles size particles larger than 0.1 μm is used. The model considers primary particles and continuous emissions. PM concentration distribution at every affected geographical point defined by a grid is computed. Stochastic uncertainty caused by the natural variability of atmospheric parameters is taken into consideration in the dispersion model by applying a Monte Carlo methodology. The prototype package (STRRAP) that takes into account the stochastic behaviour of atmospheric variables, developed for risk assessment and safe distances calculation [Godoy SM, Santa Cruz ASM, Scenna NJ. STRRAP SYSTEM - A software for hazardous materials risk assessment and safe distances calculation. Reliability Engineering and System Safety 2007;92(7):847-57] is enlarged for the analysis of the PM air dispersion. STRRAP computes distances from the source to every affected receptor in each trial and generates the impact distance distribution for each particulate size. In addition, a representative impact distance value to delimit the affected area can be obtained. Fuel oil stack effluents dispersion in Rosario city is simulated as a case study. Mass concentration distributions and impact distances are computed for the range of interest in environmental air quality evaluations (PM 2.5 -PM 10 ).

Quantity discrimination in wolves (Canis lupus

Directory of Open Access Journals (Sweden)

Ewelina eUtrata

2012-11-01

Full Text Available Quantity discrimination has been studied extensively in different non-human animal species. In the current study, we tested eleven hand-raised wolves (Canis lupus in a two-way choice task. We placed a number of food items (one to four sequentially into two opaque cans and asked the wolves to choose the larger amount. Moreover, we conducted two additional control conditions to rule out non-numerical properties of the presentation that the animals might have used to make the correct choice. Our results showed that wolves are able to make quantitative judgments at the group, but also at the individual level even when alternative strategies such as paying attention to the surface area or time and total amount are ruled out. In contrast to previous canine studies on dogs (Canis familiaris and coyotes (Canis latrans, our wolves’ performance did not improve with decreasing ratio, referred to as Weber’s law. However, further studies using larger quantities than we used in the current setup are still needed to determine whether and when wolves’ quantity discrimination conforms to Weber’s law.

Layer-Mean Quantities, Local Conservation Laws, and Vorticity

International Nuclear Information System (INIS)

Camassa, R.; Levermore, C.D.

1997-01-01

We derive local conservation laws for layer-mean quantities in two general settings. When applied to Euler flows, the first of these settings yields well-known local conservation laws for quantities averaged between material surfaces. The second, however, leads to new local conservation laws for quantities involving the vorticity that are averaged between arbitrary surfaces. These produce the crucial vorticity conservation laws in shallow water models that admit nonhydrostatic and noncolumnar motion. Moreover, they seem to lie outside the Hamiltonian paradigm of fluid dynamics. The formalism generalizes to skew-symmetric matrix fields; applications to electromagnetism are suggested. copyright 1997 The American Physical Society

The Radiometric Measurement Quantity for SAR Images

OpenAIRE

Döring, Björn J.; Schwerdt, Marco

2013-01-01

A Synthetic Aperture Radar (SAR) system measures among other quantities the terrain radar reflectivity. After image calibration, the pixel intensities are commonly expressed in terms of radar cross sections (for point targets) or as backscatter coefficients (for distributed targets), which are directly related. This paper argues that pixel intensities are not generally proportional to radar cross section or derived physical quantities. The paper further proposes to replace the inaccurate term...

Average Transverse Momentum Quantities Approaching the Lightfront

OpenAIRE

Boer, Daniel

2015-01-01

In this contribution to Light Cone 2014, three average transverse momentum quantities are discussed: the Sivers shift, the dijet imbalance, and the $p_T$ broadening. The definitions of these quantities involve integrals over all transverse momenta that are overly sensitive to the region of large transverse momenta, which conveys little information about the transverse momentum distributions of quarks and gluons inside hadrons. TMD factorization naturally suggests alternative definitions of su...

Forage quantity and quality

Science.gov (United States)

Jorgenson, Janet C.; Udevitz, Mark S.; Felix, Nancy A.; Douglas, David C.; Reynolds, Patricia E.; Rhode, E.B.

2002-01-01

The Porcupine caribou herd has traditionally used the coastal plain of the Arctic National Wildlife Refuge, Alaska, for calving. Availability of nutritious forage has been hypothesized as one of the reasons the Porcupine caribou herd migrates hundreds of kilometers to reach the coastal plain for calving (Kuropat and Bryant 1980, Russell et al. 1993).Forage quantity and quality and the chronology of snowmelt (which determines availability and phenological stages of forage) have been suggested as important habitat attributes that lead calving caribou to select one area over another (Lent 1980, White and Trudell 1980, Eastland et al. 1989). A major question when considering the impact of petroleum development is whether potential displacement of the caribou from the 1002 Area to alternate calving habitat will limit access to high quantity and quality forage.Our study had the following objectives: 1) quantify snowmelt patterns by area; 2) quantify relationships among phenology, biomass, and nutrient content of principal forage species by vegetation type; and 3) determine if traditional concentrated calving areas differ from adjacent areas with lower calving densities in terms of vegetation characteristics.

Reducing the distance in distance-caregiving by technology innovation

Directory of Open Access Journals (Sweden)

Lazelle E Benefield

2007-07-01

Full Text Available Lazelle E Benefield1, Cornelia Beck21College of Nursing, University of Oklahoma Health Sciences Center, Oklahoma City, Oklahoma, USA; 2Pat & Willard Walker Family Memory Research Center, University of Arkansas for Medical Sciences, Little Rock, Arkansas, USAAbstract: Family caregivers are responsible for the home care of over 34 million older adults in the United States. For many, the elder family member lives more than an hour’s distance away. Distance caregiving is a growing alternative to more familiar models where: 1 the elder and the family caregiver(s may reside in the same household; or 2 the family caregiver may live nearby but not in the same household as the elder. The distance caregiving model involves elders and their family caregivers who live at some distance, defined as more than a 60-minute commute, from one another. Evidence suggests that distance caregiving is a distinct phenomenon, differs substantially from on-site family caregiving, and requires additional assistance to support the physical, social, and contextual dimensions of the caregiving process. Technology-based assists could virtually connect the caregiver and elder and provide strong support that addresses the elder’s physical, social, cognitive, and/or sensory impairments. Therefore, in today’s era of high technology, it is surprising that so few affordable innovations are being marketed for distance caregiving. This article addresses distance caregiving, proposes the use of technology innovation to support caregiving, and suggests a research agenda to better inform policy decisions related to the unique needs of this situation.Keywords: caregiving, family, distance, technology, elders

Censoring distances based on labeled cortical distance maps in cortical morphometry.

Science.gov (United States)

Ceyhan, Elvan; Nishino, Tomoyuki; Alexopolous, Dimitrios; Todd, Richard D; Botteron, Kelly N; Miller, Michael I; Ratnanather, J Tilak

2013-01-01

It has been demonstrated that shape differences in cortical structures may be manifested in neuropsychiatric disorders. Such morphometric differences can be measured by labeled cortical distance mapping (LCDM) which characterizes the morphometry of the laminar cortical mantle of cortical structures. LCDM data consist of signed/labeled distances of gray matter (GM) voxels with respect to GM/white matter (WM) surface. Volumes and other summary measures for each subject and the pooled distances can help determine the morphometric differences between diagnostic groups, however they do not reveal all the morphometric information contained in LCDM distances. To extract more information from LCDM data, censoring of the pooled distances is introduced for each diagnostic group where the range of LCDM distances is partitioned at a fixed increment size; and at each censoring step, the distances not exceeding the censoring distance are kept. Censored LCDM distances inherit the advantages of the pooled distances but also provide information about the location of morphometric differences which cannot be obtained from the pooled distances. However, at each step, the censored distances aggregate, which might confound the results. The influence of data aggregation is investigated with an extensive Monte Carlo simulation analysis and it is demonstrated that this influence is negligible. As an illustrative example, GM of ventral medial prefrontal cortices (VMPFCs) of subjects with major depressive disorder (MDD), subjects at high risk (HR) of MDD, and healthy control (Ctrl) subjects are used. A significant reduction in laminar thickness of the VMPFC in MDD and HR subjects is observed compared to Ctrl subjects. Moreover, the GM LCDM distances (i.e., locations with respect to the GM/WM surface) for which these differences start to occur are determined. The methodology is also applicable to LCDM-based morphometric measures of other cortical structures affected by disease.

Censoring Distances Based on Labeled Cortical Distance Maps in Cortical Morphometry

Directory of Open Access Journals (Sweden)

Elvan eCeyhan

2013-10-01

Full Text Available It has been demonstrated that shape differences are manifested in cortical structures due to neuropsychiatric disorders. Such morphometric differences can be measured by labeled cortical distance mapping (LCDM which characterizes the morphometry of the laminar cortical mantle of cortical structures. LCDM data consist of signed/labeled distances of gray matter (GM voxels with respect to GM/white matter (WM surface. Volumes and other summary measures for each subject and the pooled distances can help determine the morphometric differences between diagnostic groups, however they do not reveal all the morphometric information con-tained in LCDM distances. To extract more information from LCDM data, censoring of the pooled distances is introduced for each diagnostic group where the range of LCDM distances is partitioned at a fixed increment size; and at each censoring step, the distances not exceeding the censoring distance are kept. Censored LCDM distances inherit the advantages of the pooled distances but also provide information about the location of morphometric differences which cannot be obtained from the pooled distances. However, at each step, the censored distances aggregate, which might confound the results. The influence of data aggregation is investigated with an extensive Monte Carlo simulation analysis and it is demonstrated that this influence is negligible. As an illustrative example, GM of ventral medial prefrontal cortices (VMPFCs of subjects with major depressive disorder (MDD, subjects at high risk (HR of MDD, and healthy control (Ctrl subjects are used. A significant reduction in laminar thickness of the VMPFC in MDD and HR subjects is observed compared to Ctrl subjects. Moreover, the GM LCDM distances (i.e., locations with respect to the GM/WM surface for which these differences start to occur are determined. The methodology is also applicable to LCDM-based morphometric measures of other cortical structures affected by disease.

Training for Distance Teaching through Distance Learning.

Science.gov (United States)

Cadorath, Jill; Harris, Simon; Encinas, Fatima

2002-01-01

Describes a mixed-mode bachelor degree course in English language teaching at the Universidad Autonoma de Puebla (Mexico) that was designed to help practicing teachers write appropriate distance education materials by giving them the experience of being distance students. Includes a course outline and results of a course evaluation. (Author/LRW)

Real-time stop sign detection and distance estimation using a single camera

Science.gov (United States)

Wang, Wenpeng; Su, Yuxuan; Cheng, Ming

2018-04-01

In modern world, the drastic development of driver assistance system has made driving a lot easier than before. In order to increase the safety onboard, a method was proposed to detect STOP sign and estimate distance using a single camera. In STOP sign detection, LBP-cascade classifier was applied to identify the sign in the image, and the principle of pinhole imaging was based for distance estimation. Road test was conducted using a detection system built with a CMOS camera and software developed by Python language with OpenCV library. Results shows that that the proposed system reach a detection accuracy of maximum of 97.6% at 10m, a minimum of 95.00% at 20m, and 5% max error in distance estimation. The results indicate that the system is effective and has the potential to be used in both autonomous driving and advanced driver assistance driving systems.

Tourists consuming distance

DEFF Research Database (Denmark)

Larsen, Gunvor Riber

The environmental impact of tourism mobility is linked to the distances travelled in order to reach a holiday destination, and with tourists travelling more and further than previously, an understanding of how the tourists view the distance they travel across becomes relevant. Based on interviews...... contribute to an understanding of how it is possible to change tourism travel behaviour towards becoming more sustainable. How tourists 'consume distance' is discussed, from the practical level of actually driving the car or sitting in the air plane, to the symbolic consumption of distance that occurs when...... travelling on holiday becomes part of a lifestyle and a social positioning game. Further, different types of tourist distance consumers are identified, ranging from the reluctant to the deliberate and nonchalant distance consumers, who display very differing attitudes towards the distance they all travel...

Analytic processing of distance.

Science.gov (United States)

Dopkins, Stephen; Galyer, Darin

2018-01-01

How does a human observer extract from the distance between two frontal points the component corresponding to an axis of a rectangular reference frame? To find out we had participants classify pairs of small circles, varying on the horizontal and vertical axes of a computer screen, in terms of the horizontal distance between them. A response signal controlled response time. The error rate depended on the irrelevant vertical as well as the relevant horizontal distance between the test circles with the relevant distance effect being larger than the irrelevant distance effect. The results implied that the horizontal distance between the test circles was imperfectly extracted from the overall distance between them. The results supported an account, derived from the Exemplar Based Random Walk model (Nosofsky & Palmieri, 1997), under which distance classification is based on the overall distance between the test circles, with relevant distance being extracted from overall distance to the extent that the relevant and irrelevant axes are differentially weighted so as to reduce the contribution of irrelevant distance to overall distance. The results did not support an account, derived from the General Recognition Theory (Ashby & Maddox, 1994), under which distance classification is based on the relevant distance between the test circles, with the irrelevant distance effect arising because a test circle's perceived location on the relevant axis depends on its location on the irrelevant axis, and with relevant distance being extracted from overall distance to the extent that this dependency is absent. Copyright © 2017 Elsevier B.V. All rights reserved.

Distancing, not embracing, the Distancing-Embracing model of art reception.

Science.gov (United States)

Davies, Stephen

2017-01-01

Despite denials in the target article, the Distancing-Embracing model appeals to compensatory ideas in explaining the appeal of artworks that elicit negative affect. The model also appeals to the deflationary effects of psychological distancing. Having pointed to the famous rejection in the 1960s of the view that aesthetic experience involves psychological distancing, I suggest that "distance" functions here as a weak metaphor that cannot sustain the explanatory burden the theory demands of it.

A conserved quantity in thin body dynamics

Science.gov (United States)

Hanna, J. A.; Pendar, H.

2016-02-01

Thin, solid bodies with metric symmetries admit a restricted form of reparameterization invariance. Their dynamical equilibria include motions with both rigid and flowing aspects. On such configurations, a quantity is conserved along the intrinsic coordinate corresponding to the symmetry. As an example of its utility, this conserved quantity is combined with linear and angular momentum currents to construct solutions for the equilibria of a rotating, flowing string, for which it is akin to Bernoulli's constant.

Relationships of chemical composition, quantity of milt to fertility and ...

African Journals Online (AJOL)

African Journal of Food, Agriculture, Nutrition and Development ... determining the right quantity of milt that can be used to fertilize certain quantity of eggs. ... quantity of milt used for artificial reproduction in fish significantly affect water quality used ... is the major organic substance that supplies the spermatozoa with energy.

Six categories of ionizing radiation quantities practical in various fields

International Nuclear Information System (INIS)

Zheng Junzheng; Zhuo Weihai

2011-01-01

This paper is the part of review on the evolvement of the systems for ionizing radiation quantities and units. In the paper, for better understanding and correct use of the relevant quantities of ionizing radiation, the major ionizing radiation quantities in various fields are divided into six categories. (authors)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

International Nuclear Information System (INIS)

Liu Xiao-Wei; Li Yuan-Cheng

2011-01-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry. (general)

Lie-Mei symmetry and conserved quantities of the Rosenberg problem

Science.gov (United States)

Liu, Xiao-Wei; Li, Yuan-Cheng

2011-07-01

The Rosenberg problem is a typical but not too complicated problem of nonholonomic mechanical systems. The Lie—Mei symmetry and the conserved quantities of the Rosenberg problem are studied. For the Rosenberg problem, the Lie and the Mei symmetries for the equation are obtained, the conserved quantities are deduced from them and then the definition and the criterion for the Lie—Mei symmetry of the Rosenberg problem are derived. Finally, the Hojman conserved quantity and the Mei conserved quantity are deduced from the Lie—Mei symmetry.

Optimal trading quantity integration as a basis for optimal portfolio management

Directory of Open Access Journals (Sweden)

Saša Žiković

2005-06-01

Full Text Available The author in this paper points out the reason behind calculating and using optimal trading quantity in conjunction with Markowitz’s Modern portfolio theory. In the opening part the author presents an example of calculating optimal weights using Markowitz’s Mean-Variance approach, followed by an explanation of basic logic behind optimal trading quantity. The use of optimal trading quantity is not limited to systems with Bernoulli outcome, but can also be used when trading shares, futures, options etc. Optimal trading quantity points out two often-overlooked axioms: (1 a system with negative mathematical expectancy can never be transformed in a system with positive mathematical expectancy, (2 by missing the optimal trading quantity an investor can turn a system with positive expectancy into a negative one. Optimal trading quantity is that quantity which maximizes geometric mean (growth function of a particular system. To determine the optimal trading quantity for simpler systems, with a very limited number of outcomes, a set of Kelly’s formulas is appropriate. In the conclusion the summary of the paper is presented.

Foundations of Distance Education. Third Edition. Routledge Studies in Distance Education.

Science.gov (United States)

Keegan, Desmond

This text gives an overview of distance education for students, administrators, and practitioners in distance education. Chapter 1 discusses the study of distance education. Chapter 2 analyzes forms of nonconventional education (open, nontraditional) that may have similarities to distance education but are not to be identified with it. Chapter 3…

21 CFR 1314.20 - Restrictions on sales quantity.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Restrictions on sales quantity. 1314.20 Section 1314.20 Food and Drugs DRUG ENFORCEMENT ADMINISTRATION, DEPARTMENT OF JUSTICE RETAIL SALE OF SCHEDULED LISTED CHEMICAL PRODUCTS Sales by Regulated Sellers § 1314.20 Restrictions on sales quantity. (a) Without...

modelling distances

Directory of Open Access Journals (Sweden)

Robert F. Love

2001-01-01

Full Text Available Distance predicting functions may be used in a variety of applications for estimating travel distances between points. To evaluate the accuracy of a distance predicting function and to determine its parameters, a goodness-of-fit criteria is employed. AD (Absolute Deviations, SD (Squared Deviations and NAD (Normalized Absolute Deviations are the three criteria that are mostly employed in practice. In the literature some assumptions have been made about the properties of each criterion. In this paper, we present statistical analyses performed to compare the three criteria from different perspectives. For this purpose, we employ the ℓkpθ-norm as the distance predicting function, and statistically compare the three criteria by using normalized absolute prediction error distributions in seventeen geographical regions. We find that there exist no significant differences between the criteria. However, since the criterion SD has desirable properties in terms of distance modelling procedures, we suggest its use in practice.

High Speed Railway Environment Safety Evaluation Based on Measurement Attribute Recognition Model

Directory of Open Access Journals (Sweden)

Qizhou Hu

2014-01-01

Full Text Available In order to rationally evaluate the high speed railway operation safety level, the environmental safety evaluation index system of high speed railway should be well established by means of analyzing the impact mechanism of severe weather such as raining, thundering, lightning, earthquake, winding, and snowing. In addition to that, the attribute recognition will be identified to determine the similarity between samples and their corresponding attribute classes on the multidimensional space, which is on the basis of the Mahalanobis distance measurement function in terms of Mahalanobis distance with the characteristics of noncorrelation and nondimensionless influence. On top of the assumption, the high speed railway of China environment safety situation will be well elaborated by the suggested methods. The results from the detailed analysis show that the evaluation is basically matched up with the actual situation and could lay a scientific foundation for the high speed railway operation safety.

Simple, distance-dependent formulation of the Watts-Strogatz model for directed and undirected small-world networks

Science.gov (United States)

Song, H. Francis; Wang, Xiao-Jing

2014-12-01

Small-world networks—complex networks characterized by a combination of high clustering and short path lengths—are widely studied using the paradigmatic model of Watts and Strogatz (WS). Although the WS model is already quite minimal and intuitive, we describe an alternative formulation of the WS model in terms of a distance-dependent probability of connection that further simplifies, both practically and theoretically, the generation of directed and undirected WS-type small-world networks. In addition to highlighting an essential feature of the WS model that has previously been overlooked, namely the equivalence to a simple distance-dependent model, this alternative formulation makes it possible to derive exact expressions for quantities such as the degree and motif distributions and global clustering coefficient for both directed and undirected networks in terms of model parameters.

Measuring Algorithm for the Distance to a Preceding Vehicle on Curve Road Using On-Board Monocular Camera

Science.gov (United States)

Yu, Guizhen; Zhou, Bin; Wang, Yunpeng; Wun, Xinkai; Wang, Pengcheng

2015-12-01

Due to more severe challenges of traffic safety problems, the Advanced Driver Assistance Systems (ADAS) has received widespread attention. Measuring the distance to a preceding vehicle is important for ADAS. However, the existing algorithm focuses more on straight road sections than on curve measurements. In this paper, we present a novel measuring algorithm for the distance to a preceding vehicle on a curve road using on-board monocular camera. Firstly, the characteristics of driving on the curve road is analyzed and the recognition of the preceding vehicle road area is proposed. Then, the vehicle detection and distance measuring algorithms are investigated. We have verified these algorithms on real road driving. The experimental results show that this method proposed in the paper can detect the preceding vehicle on curve roads and accurately calculate the longitudinal distance and horizontal distance to the preceding vehicle.

Quantity-split strategy under two-contractor competitive procurement environment

OpenAIRE

Boger, Dan C.; Liao, Shu S.

1988-01-01

This report discusses the various market scenarios that provide bid price manipulation opportunities under the dual source competition environment. Two different quantity-split strategies were developed one for the case when one of the suppliers does not have the capacity to produce the majority of the annual quantity requirement and the other for the case when neither contractor is interested in using low prices to capture the larger share of annual quantity. Keywords: Dual sourcing, Quantit...

Safety analysis report for packaging (onsite) for limited type Bmaterial in the CNS 14-215H cask

International Nuclear Information System (INIS)

Flanagan, B.D.

1997-01-01

The purpose of this Safety Analysis Report for Packaging is to provide the analyses and evaluations necessary to demonstrate that the CNS 14-215H cask provided by Chem-Nuclear Systems Inc. can safety transport greater than Type A quantities of radioactive material on the Hanford Site. The CNS 14-215H cask was chosen for its loading abilities, availability, and because it has a Certificate of Compliance (CoC) issued by the U.S. Nuclear Regulatory Commission (NRC) for transporting low specific activity in quantities greater than Type A material in commerce. Although the CDC does not cover greater than Type A material not meeting LSA requirements, it does allow for an established level of protection in determining the safety of transporting Type B material on the Hanford Site

Editorial: New operational dose equivalent quantities

International Nuclear Information System (INIS)

Harvey, J.R.

1985-01-01

The ICRU Report 39 entitled ''Determination of Dose Equivalents Resulting from External Radiation Sources'' is briefly discussed. Four new operational dose equivalent quantities have been recommended in ICRU 39. The 'ambient dose equivalent' and the 'directional dose equivalent' are applicable to environmental monitoring and the 'individual dose equivalent, penetrating' and the 'individual dose equivalent, superficial' are applicable to individual monitoring. The quantities should meet the needs of day-to-day operational practice, while being acceptable to those concerned with metrological precision, and at the same time be used to give effective control consistent with current perceptions of the risks associated with exposure to ionizing radiations. (U.K.)

Brownian distance covariance

OpenAIRE

Székely, Gábor J.; Rizzo, Maria L.

2010-01-01

Distance correlation is a new class of multivariate dependence coefficients applicable to random vectors of arbitrary and not necessarily equal dimension. Distance covariance and distance correlation are analogous to product-moment covariance and correlation, but generalize and extend these classical bivariate measures of dependence. Distance correlation characterizes independence: it is zero if and only if the random vectors are independent. The notion of covariance with...

Study on estimation of evacuation distances for nuclear emergency

International Nuclear Information System (INIS)

Sato, Sohei; Homma, Toshimitsu

2005-09-01

Japan Atomic Energy Research Institute (JAERI) have conducted the analytical studies on the Probabilistic Safety Assessment (PSA), the severe accidents, and the optimization of protective actions. Based on the results of these studies, JAERI are investigating the method for taking urgent protective actions more reasonably. If an accident occurs in a nuclear power plant (NPP), early protective actions are carried out. To implement these actions more effectively, emergency preparedness and emergency planning are important, and especially prompt evacuation is expected to reduce a large amount of radiation exposures. To examine the effect of early protective measures by using a PSA method, estimation of the parameter uncertainty related in the time for early protective actions is needed. For this purpose, we have developed an analytical method for urgent protective actions using geographic information, and estimated the movement distance based on gathering points arrangement an population distribution. For this analysis, we used the gathering point data shown on each regional plans for disaster prevention which will be used in actual emergency situation and targeted the population inside Emergency Planning Zone (EPZ). By applying this method for the existing sixteen commercial NPP sites, we estimated the average value and distribution of the movement distance for each sites. This report provides a brief description of the method for estimating the movement distance, input data for this analysis, and the result. Moreover, the problem on the method of evacuation distance analysis and usefulness of this method for emergency planning were discussed. (author)

Traversing psychological distance.

Science.gov (United States)

Liberman, Nira; Trope, Yaacov

2014-07-01

Traversing psychological distance involves going beyond direct experience, and includes planning, perspective taking, and contemplating counterfactuals. Consistent with this view, temporal, spatial, and social distances as well as hypotheticality are associated, affect each other, and are inferred from one another. Moreover, traversing all distances involves the use of abstraction, which we define as forming a belief about the substitutability for a specific purpose of subjectively distinct objects. Indeed, across many instances of both abstraction and psychological distancing, more abstract constructs are used for more distal objects. Here, we describe the implications of this relation for prediction, choice, communication, negotiation, and self-control. We ask whether traversing distance is a general mental ability and whether distance should replace expectancy in expected-utility theories. Copyright © 2014 Elsevier Ltd. All rights reserved.

30 CFR 77.807-2 - Booms and masts; minimum distance from high-voltage lines.

Science.gov (United States)

2010-07-01

...-voltage lines. 77.807-2 Section 77.807-2 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.807-2 Booms and masts; minimum distance from high-voltage lines. The booms and masts of equipment operated on the surface of any...

48 CFR 245.7309-8 - Variations in quantity or weight.

Science.gov (United States)

2010-10-01

... Inventory 245.7309-8 Variations in quantity or weight. When property is sold on a “unit price” basis, the Contractor reserves the right to vary by up to 15 percent the quantity or weight listed in the Invitation and... price shall be adjusted in accordance with the unit price and on the basis of the quantity or weight...

Safety considerations and countermeasures against fire and explosion at an HTGR-hydrogen production system. Proposal of safety design concept

International Nuclear Information System (INIS)

Nishihara, T.; Hada, K.; Shibata, T.; Shiozawa, S.

1996-01-01

Establishment of safety design concept and countermeasures against fire and explosion accidents is among key safety-related issues in an HTGR-hydrogen production system. We propose the different safety design concepts depending upon the origin of fire and explosion which may happen in the HTGR-hydrogen production plant. Against fire and explosion originated outside the reactor building (R/B), namely in the area of hydrogen production plant, the safety design concept is primarily to take a safe distance for preventing the damage on safety-related items or a proof wall if necessary. Because the hydrogen production plant is designed in the same safety level as a conventional chemical plant. The safe distance is proposed to limit an incident overpressure to 10 kPa so as not to suffer any damage on the items and to limit a wall-averaged temperature of concrete structures of the R/B to 175degC according to the current regulation. On the other hand, against a potential possibility of explosion originated inside the R/B, the safety design concept is to minimize the possibility of explosion low enough to assume no occurrence inside the R/B. That is, the measure is to exclude a simultaneous failure of a secondary helium piping and an endothermic chemical reactor. Furthermore, in severe accident condition in which the explosion may be postulated a priori, an incidental overpressure of explosion inside the reactor containment vessel (C/V) should be limited so as not to fail the C/V through restricting the amount of combustible gas ingress into the C/V by means of a combination of C/V isolation valve installed in the helium piping and emergency shut off valve in the process feed gas line. (author)

Safety and environmental aspects of heavy water production (Paper No. 4.1)

International Nuclear Information System (INIS)

Singh, Mohinder

1992-01-01

Different processes are utilised for heavy water production in the heavy water plants in India. H 2 S is used in large quantities as carrier gas to extract deuterium content from water. The safe handling of such large quantities of H 2 S gas poses a major problem because of its toxicity, high corrosive nature and high flammability. Handling of large quantities of synthesis gas in ammonia based plants at high pressure and temperature poses a major problem because it is a mixture of hydrogen and nitrogen. H 2 is highly inflammable and explosive when mixed with air or oxygen. All the safety aspects considered while designing, fabricating, constructing and operating the plants are described. (author). 5 tabs

Safety analysis and inventory control of transuranic and low-level waste in common storage

International Nuclear Information System (INIS)

Porten, D.R.; Bonner, A.L.; Joyce, J.P.

1993-01-01

This paper describes a methodology developed For the inventory control of low-level waste (LLW) and transuranic (TRU) waste, when both are stored in the same location, and both contribute to an inventory constrained by safety considerations. Development of the method arose from the necessity to make safety analysis calculations for the addition of LLW, in quantities greater than existing inventory limits would allow when stored with TRU waste, in the Hanford Central Waste Complex (CWC)-Ensuring that the dose consequences of credible releases are maintained at low-hazard limits or less, was used to allow greater than Type A quantities of LLW into the CWC. Basically, what happens is the original limited amount of TRU allowed is reduced by some equivalent amount of LLW introduced. The total quantity of TRU, and LLW in excess of Type A quantities, must be administratively maintained via curie equivalency Factors to ensure operation as a low-hazard Facility. The ''equivalency'' between TRU and LLW proposed here is specific only to the CWC, but the methodology can be used for other specific applications, such as TRU and LLW storage or handling facilities where inventory limits must be enforced or where a simplified inventory system is required

Discussion on concepts for radiological dosimetric quantities in the Japan Health Physics Society

International Nuclear Information System (INIS)

Takahashi, Fumiaki; Oda, Keiji

2007-01-01

Many dosimetric quantities have been used for radiation protection purpose. The International Commission on Radiological Protection (ICRP) has recommended protection quantities and the International Commission on Radiation Units and Measurements (ICRU) has introduced operational quantities to provide a reasonable estimate of the protection quantities. Enthusiastic discussions are continuously made on the issues of the dosimetric quantities, such as basic biological data for the definition of these quantities and applicability of the quantities to actual radiation protection practice. At the moment, some changes are being proposed concerning dosimetric quantities in the draft recommendations of ICRP, opened for consultation in recent years. Thus, the Japan Health Physics Society (JHPS) established the Expert Committee on concepts of Dosimetric Quantities used in radiological protection (ECDQ) in April 2005 to reviewed and discuss issues in the dosimetric quantities. (author)

Transient diagnosis system using quantum-inspired computing and Minkowski distance

Energy Technology Data Exchange (ETDEWEB)

Nicolau, Andressa dos Santos; Schirru, Roberto, E-mail: andressa@lmp.ufrj.b, E-mail: schirru@lmp.ufrj.b [Federal University of Rio de Janeiro (PEN/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Nuclear Engineering Program

2011-07-01

This paper proposes a diagnosis system model for identification of transient in a PWR nuclear power plant, optimized by the Quantum Inspired Evolutionary Algorithm - QEA in order to help nuclear power plant operator reduce his cognitive load and increase his available time to maintain the plant operating in a safe condition. This method was developed in order to be able to recognize the normal condition and three accidents of the design basis list of the nuclear power plant Angra 2, postulated in the Final Safety Analysis Report (FSAR). This System compares the similarly distance between the set of variables of the anomalous event, in a given time t, and the centroids of the design-basis transient variables. The lower similarly distance indicates the class of the transient to which the anomalous event belongs. The QEA was then used to find the best position of the centroids of each class of the selected transients. Such positions maximize the number of the correct classifications. Unlike the diagnosis system proposed in the literature, Minkowski distance was employed to calculate the similarity distance. The signatures of four transients were submitted to 1% and 2% of noise, and tested with prototype vector found by QEA. The results showed that the present transient diagnostic system was successfully implemented in the nuclear accident identification problem and was compatible with the techniques presented in the literature. (author)

Transient diagnosis system using quantum-inspired computing and Minkowski distance

International Nuclear Information System (INIS)

Nicolau, Andressa dos Santos; Schirru, Roberto

2011-01-01

This paper proposes a diagnosis system model for identification of transient in a PWR nuclear power plant, optimized by the Quantum Inspired Evolutionary Algorithm - QEA in order to help nuclear power plant operator reduce his cognitive load and increase his available time to maintain the plant operating in a safe condition. This method was developed in order to be able to recognize the normal condition and three accidents of the design basis list of the nuclear power plant Angra 2, postulated in the Final Safety Analysis Report (FSAR). This System compares the similarly distance between the set of variables of the anomalous event, in a given time t, and the centroids of the design-basis transient variables. The lower similarly distance indicates the class of the transient to which the anomalous event belongs. The QEA was then used to find the best position of the centroids of each class of the selected transients. Such positions maximize the number of the correct classifications. Unlike the diagnosis system proposed in the literature, Minkowski distance was employed to calculate the similarity distance. The signatures of four transients were submitted to 1% and 2% of noise, and tested with prototype vector found by QEA. The results showed that the present transient diagnostic system was successfully implemented in the nuclear accident identification problem and was compatible with the techniques presented in the literature. (author)

Management of small quantities of radioactive waste

International Nuclear Information System (INIS)

1998-09-01

The main objective of this publication is to provide practical guidance primarily to developing Member States on the predisposal management of small quantities of radioactive waste arising from hospitals, laboratories, industries, institutions, research reactors and research centres.The publication covers the management of liquid, solid and gaseous radioactive wastes at the users' premises and gives general guidance on procedures at a centralized waste management facility. Predisposal management of radioactive waste includes handling, treatment, conditioning, storage and transportation. This publication provides information and guidance on the following topics: national waste management framework; origin and characteristics of radioactive waste arising from users generating small quantities of waste; radioactive waste management concepts appropriate for small quantities; local waste management; the documentation and approval necessary for the consignment of waste to a centralized waste management facility; centralized waste management; exemption of radionuclides from the regulatory body; transportation; environmental monitoring; quality assurance for the whole predisposal process; regional co-operation aspects

RISK-INFORMED SAFETY MARGIN CHARACTERIZATION

International Nuclear Information System (INIS)

Dinh, Nam; Szilard, Ronaldo

2009-01-01

The concept of safety margins has served as a fundamental principle in the design and operation of commercial nuclear power plants (NPPs). Defined as the minimum distance between a system's 'loading' and its 'capacity', plant design and operation is predicated on ensuring an adequate safety margin for safety-significant parameters (e.g., fuel cladding temperature, containment pressure, etc.) is provided over the spectrum of anticipated plant operating, transient and accident conditions. To meet the anticipated challenges associated with extending the operational lifetimes of the current fleet of operating NPPs, the United States Department of Energy (USDOE), the Idaho National Laboratory (INL) and the Electric Power Research Institute (EPRI) have developed a collaboration to conduct coordinated research to identify and address the technological challenges and opportunities that likely would affect the safe and economic operation of the existing NPP fleet over the postulated long-term time horizons. In this paper we describe a framework for developing and implementing a Risk-Informed Safety Margin Characterization (RISMC) approach to evaluate and manage changes in plant safety margins over long time horizons

30 CFR 77.807-3 - Movement of equipment; minimum distance from high-voltage lines.

Science.gov (United States)

2010-07-01

... high-voltage lines. 77.807-3 Section 77.807-3 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION... WORK AREAS OF UNDERGROUND COAL MINES Surface High-Voltage Distribution § 77.807-3 Movement of equipment; minimum distance from high-voltage lines. When any part of any equipment operated on the surface of any...

Dosimetric radiation protection quantities. Impact of the forthcoming ICRP recommendations

International Nuclear Information System (INIS)

Pradhan, A.S.; Lee, J.I.; Kim, J.L.; Kim, B.H.

2008-01-01

The physical quantities namely fluence, kerma and absorbed dose provide the base for the operational and the protection quantities. The absorbed dose continues to be the fundamental physical quantity for the radiological protection. The most striking feature relating the quantities in the forthcoming recommendations is the updating of the radiation and tissue weighting factors based on the latest available scientific information on radiobiology and the physics of radiation exposure. This is bound to make a significant impact in arriving at the equivalent doses and effective dose. For external exposures of neutrons, the forthcoming recommendations are going to improve the relationship between the operational and protection quantities. The changes in the tissue weighting factors of some tissues/organs, the inclusion of several new tissues/organs for the consideration of tissue weighting factors and the use of the proposed Reference Male and Reference Female voxel phantoms would require new conversion coefficients and dose coefficients for external and internal exposures. The other striking feature appears to be the details of the concepts to ensure that the protections quantities are used for the appropriate and intended purposes only and the misuse is avoided. (author)

Development of Onsite Transportation Safety Documents for Nevada Test Site

International Nuclear Information System (INIS)

Frank Hand; Willard Thomas; Frank Sciacca; Manny Negrete; Susan Kelley

2008-01-01

Department of Energy (DOE) Orders require each DOE site to develop onsite transportation safety documents (OTSDs). The Nevada Test Site approach divided all onsite transfers into two groups with each group covered by a standalone OTSD identified as Non-Nuclear and Nuclear. The Non-Nuclear transfers involve all radioactive hazardous material in less than Hazard Category (HC)-3 quantities and all chemically hazardous materials. The Nuclear transfers involve all radioactive material equal to or greater than HC-3 quantities and radioactive material mated with high explosives regardless of quantity. Both OTSDs comply with DOE O 460.1B requirements. The Nuclear OTSD also complies with DOE O 461.1A requirements and includes a DOE-STD-3009 approach to hazard analysis (HA) and accident analysis as needed. All Nuclear OTSD proposed transfers were determined to be non-equivalent and a methodology was developed to determine if 'equivalent safety' to a fully compliant Department of Transportation (DOT) transfer was achieved. For each HA scenario, three hypothetical transfers were evaluated: a DOT-compliant, uncontrolled, and controlled transfer. Equivalent safety is demonstrated when the risk level for each controlled transfer is equal to or less than the corresponding DOT-compliant transfer risk level. In this comparison the typical DOE-STD-3009 risk matrix was modified to reflect transportation requirements. Design basis conditions (DBCs) were developed for each non-equivalent transfer. Initial DBCs were based solely upon the amount of material present. Route-, transfer-, and site-specific conditions were evaluated and the initial DBCs revised as needed. Final DBCs were evaluated for each transfer's packaging and its contents

Open and Distance Learning Today. Routledge Studies in Distance Education Series.

Science.gov (United States)

Lockwood, Fred, Ed.

This book contains the following papers on open and distance learning today: "Preface" (Daniel); "Big Bang Theory in Distance Education" (Hawkridge); "Practical Agenda for Theorists of Distance Education" (Perraton); "Trends, Directions and Needs: A View from Developing Countries" (Koul); "American…

Generalized correlation integral vectors: A distance concept for chaotic dynamical systems

Energy Technology Data Exchange (ETDEWEB)

Haario, Heikki, E-mail: heikki.haario@lut.fi [School of Engineering Science, Lappeenranta University of Technology, Lappeenranta (Finland); Kalachev, Leonid, E-mail: KalachevL@mso.umt.edu [Department of Mathematical Sciences, University of Montana, Missoula, Montana 59812-0864 (United States); Hakkarainen, Janne [Earth Observation Unit, Finnish Meteorological Institute, Helsinki (Finland)

2015-06-15

Several concepts of fractal dimension have been developed to characterise properties of attractors of chaotic dynamical systems. Numerical approximations of them must be calculated by finite samples of simulated trajectories. In principle, the quantities should not depend on the choice of the trajectory, as long as it provides properly distributed samples of the underlying attractor. In practice, however, the trajectories are sensitive with respect to varying initial values, small changes of the model parameters, to the choice of a solver, numeric tolerances, etc. The purpose of this paper is to present a statistically sound approach to quantify this variability. We modify the concept of correlation integral to produce a vector that summarises the variability at all selected scales. The distribution of this stochastic vector can be estimated, and it provides a statistical distance concept between trajectories. Here, we demonstrate the use of the distance for the purpose of estimating model parameters of a chaotic dynamic model. The methodology is illustrated using computational examples for the Lorenz 63 and Lorenz 95 systems, together with a framework for Markov chain Monte Carlo sampling to produce posterior distributions of model parameters.

Calibration of personal dosimeters: Quantities and terminology

International Nuclear Information System (INIS)

Aleinikov, V.E.

1999-01-01

The numerical results obtained in the interpretation of individual monitoring of external radiation depend not only on the accurate calibration of the radiation measurement instruments involved, but also on the definition of the quantities in term of which these instruments are calibrated The absence of uniformity in terminology not only makes it difficult to understand properly the scientific and technical literature but can also lead to incorrect interpretation of particular concepts and recommendations. In this paper, brief consideration is given to definition of radiation quantities and terminology used in calibration procedures. (author)

On pure-strategy Nash equilibria in price-quantity games

NARCIS (Netherlands)

Bos, I.; Vermeulen, A.J.

2015-01-01

This paper examines the existence and characteristics of pure-strategy Nash equilibria in oligopoly models in which firms set both prices and quantities. Existence is proved for a broad and natural class of price-quantity games. With differentiated products, the equilibrium outcome is similar to

Psychological distance of pedestrian at the bus terminal area

Science.gov (United States)

Firdaus Mohamad Ali, Mohd; Salleh Abustan, Muhamad; Hidayah Abu Talib, Siti; Abustan, Ismail; Rahman, Noorhazlinda Abd; Gotoh, Hitoshi

2018-03-01

Walking is a part of transportation modes that is effective for pedestrian in either short or long trips. All people are classified as pedestrian because people do walk every day and the higher number of people walking will lead to crowd conditions and that is the reason of the importance to study about the behaviour of pedestrian specifically the psychological distance in both indoor and outdoor. Nowadays, the number of studies of crowd dynamics among pedestrian have increased due to the concern about the safety issues primarily related to the emergency cases such as fire, earthquake, festival and etc. An observation of pedestrian was conducted at one of the main bus terminals in Kuala Lumpur with the main objective to obtain pedestrian psychological distance and it took place for 45 minutes by using a camcorder that was set up by using a tripod on the upper floor from the area of observation at the main lobby and the trapped area was approximately 100 m2. The analysis was focused on obtaining the gap between pedestrian based on two different categories, which are; (a) Pedestrian with relationship, and (b) Pedestrian without relationship. In total, 1,766 data were obtained during the analysis in which 561 data were obtained for `Pedestrian with relationship' and 1,205 data were obtained for "Pedestrian without relationship". Based on the obtained results, "Pedestrian without relationship" had shown a slightly higher average value of psychological distance between them compare to "Pedestrian with relationship" with the results of 1.6360m and 1.5909m respectively. In gender case, "Pedestrian without relationship" had higher mean of psychological distance in all three categories as well. Therefore, it can be concluded that pedestrian without relationship tend to have longer distance when walking in crowds.

Safety in handling helium and nitrogen

International Nuclear Information System (INIS)

Schmauch, G.; Lansing, L.; Santay, T.; Nahmias, D.

1991-01-01

Based upon the authors' industrial experience and practices, they have provided an overview of safety in storage, handling, and transfer of both laboratory and bulk quantities of gaseous and liquid forms of nitrogen and helium. They have addressed the properties and characteristics of both the gaseous and liquid fluids, typical storage and transport containers, transfer techniques, and the associated hazards which include low temperatures, high pressures, and asphyxiation. Methods and procedures to control and eliminate these hazards are described, as well as risk remediation through safety awareness training, personal protective equipment, area ventilation, and atmosphere monitoring. They have included as an example a recent process hazards analysis performed by Air Products on the asphyxiation hazard associated with the use of liquid helium in MRI magnet systems

From a distance: implications of spontaneous self-distancing for adaptive self-reflection.

Science.gov (United States)

Ayduk, Ozlem; Kross, Ethan

2010-05-01

Although recent experimental work indicates that self-distancing facilitates adaptive self-reflection, it remains unclear (a) whether spontaneous self-distancing leads to similar adaptive outcomes, (b) how spontaneous self-distancing relates to avoidance, and (c) how this strategy impacts interpersonal behavior. Three studies examined these issues demonstrating that the more participants spontaneously self-distanced while reflecting on negative memories, the less emotional (Studies 1-3) and cardiovascular (Study 2) reactivity they displayed in the short term. Spontaneous self-distancing was also associated with lower emotional reactivity and intrusive ideation over time (Study 1). The negative association between spontaneous self-distancing and emotional reactivity was mediated by how participants construed their experience (i.e., less recounting relative to reconstruing) rather than avoidance (Studies 1-2). In addition, spontaneous self-distancing was associated with more problem-solving behavior and less reciprocation of negativity during conflicts among couples in ongoing relationships (Study 3). Although spontaneous self-distancing was empirically related to trait rumination, it explained unique variance in predicting key outcomes. 2010 APA, all rights reserved

Definitions of Quantities and Units.

Science.gov (United States)

Spurgin, C. B.

1983-01-01

Compares various methods of defining derived quantities, arguing for a definitional formula using base or fundamental units in a word equation, or symbol-equations with the symbols explained. Suggests that fundamental units be defined operationally or left regarded as intuitive as in the case of length and time. (JM)

Distance-regular graphs

NARCIS (Netherlands)

van Dam, Edwin R.; Koolen, Jack H.; Tanaka, Hajime

2016-01-01

This is a survey of distance-regular graphs. We present an introduction to distance-regular graphs for the reader who is unfamiliar with the subject, and then give an overview of some developments in the area of distance-regular graphs since the monograph 'BCN'[Brouwer, A.E., Cohen, A.M., Neumaier,

Process safety management for highly hazardous chemicals

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-01

Purpose of this document is to assist US DOE contractors who work with threshold quantities of highly hazardous chemicals (HHCs), flammable liquids or gases, or explosives in successfully implementing the requirements of OSHA Rule for Process Safety Management of Highly Hazardous Chemicals (29 CFR 1910.119). Purpose of this rule is to prevent releases of HHCs that have the potential to cause catastrophic fires, explosions, or toxic exposures.

Detection Dynamics Of Nitrogen Based Explosive Quantities In Selected Cylindrical Containers

Directory of Open Access Journals (Sweden)

Ngusha Tavershima Almighty

2017-12-01

Full Text Available An experimental set up for examining the variation of detection intensity with explosive quantity has been studied. Containers made from ceramic carbon steel wood and HDPE were filled with explosive masses ranging from 10 kg to 500 kg and irradiated by a 14.1 MeV point isotropic neutron source. The resulting gamma photons were analyzed for their C N and O composition and the sum computed to yield a quantity known as the material quotient MQ. Examination of MQ values indicates an initial increase in detection intensity with increasing explosive quantity. Saturation is however reached at an explosive quantity of about 25kg where detection intensity reduces with further increase in explosive quantity. Effects of variation in explosive quantity appeared to be more pronounced for explosives contained in HDPE and wooden containers and least pronounced for those in steel containers. Source-detector configuration was identified as a major factor affecting effective detection of large masses of explosives.

Workplace stress experienced by quantity surveyors

African Journals Online (AJOL)

Paul (P.A.) Bowen, Department of Construction Economics and Management,. University of Cape Town, Private ..... Explore workplace stress levels among quantity surveyors in the developing nation of ...... London: Free. Association Books.

Hierarchical traits distances explain grassland Fabaceae species' ecological niches distances

Science.gov (United States)

Fort, Florian; Jouany, Claire; Cruz, Pablo

2015-01-01

Fabaceae species play a key role in ecosystem functioning through their capacity to fix atmospheric nitrogen via their symbiosis with Rhizobium bacteria. To increase benefits of using Fabaceae in agricultural systems, it is necessary to find ways to evaluate species or genotypes having potential adaptations to sub-optimal growth conditions. We evaluated the relevance of phylogenetic distance, absolute trait distance and hierarchical trait distance for comparing the adaptation of 13 grassland Fabaceae species to different habitats, i.e., ecological niches. We measured a wide range of functional traits (root traits, leaf traits, and whole plant traits) in these species. Species phylogenetic and ecological distances were assessed from a species-level phylogenetic tree and species' ecological indicator values, respectively. We demonstrated that differences in ecological niches between grassland Fabaceae species were related more to their hierarchical trait distances than to their phylogenetic distances. We showed that grassland Fabaceae functional traits tend to converge among species with the same ecological requirements. Species with acquisitive root strategies (thin roots, shallow root systems) are competitive species adapted to non-stressful meadows, while conservative ones (coarse roots, deep root systems) are able to tolerate stressful continental climates. In contrast, acquisitive species appeared to be able to tolerate low soil-P availability, while conservative ones need high P availability. Finally we highlight that traits converge along the ecological gradient, providing the assumption that species with similar root-trait values are better able to coexist, regardless of their phylogenetic distance. PMID:25741353

Hierarchical traits distances explain grassland Fabaceae species’ ecological niches distances

Directory of Open Access Journals (Sweden)

Florian eFort

2015-02-01

Full Text Available Fabaceae species play a key role in ecosystem functioning through their capacity to fix atmospheric nitrogen via their symbiosis with Rhizobium bacteria. To increase benefits of using Fabaceae in agricultural systems, it is necessary to find ways to evaluate species or genotypes having potential adaptations to sub-optimal growth conditions. We evaluated the relevance of phylogenetic distance, absolute trait distance and hierarchical trait distance for comparing the adaptation of 13 grassland Fabaceae species to different habitats, i.e. ecological niches. We measured a wide range of functional traits (root traits, leaf traits and whole plant traits in these species. Species phylogenetic and ecological distances were assessed from a species-level phylogenetic tree and species’ ecological indicator values, respectively. We demonstrated that differences in ecological niches between grassland Fabaceae species were related more to their hierarchical trait distances than to their phylogenetic distances. We showed that grassland Fabaceae functional traits tend to converge among species with the same ecological requirements. Species with acquisitive root strategies (thin roots, shallow root systems are competitive species adapted to non-stressful meadows, while conservative ones (coarse roots, deep root systems are able to tolerate stressful continental climates. In contrast, acquisitive species appeared to be able to tolerate low soil-P availability, while conservative ones need high P availability. Finally we highlight that traits converge along the ecological gradient, providing the assumption that species with similar root-trait values are better able to coexist, regardless of their phylogenetic distance.

Numerical distance protection

CERN Document Server

Ziegler, Gerhard

2011-01-01

Distance protection provides the basis for network protection in transmission systems and meshed distribution systems. This book covers the fundamentals of distance protection and the special features of numerical technology. The emphasis is placed on the application of numerical distance relays in distribution and transmission systems.This book is aimed at students and engineers who wish to familiarise themselves with the subject of power system protection, as well as the experienced user, entering the area of numerical distance protection. Furthermore it serves as a reference guide for s

Development of effective means of propaganda of safety techniques for coal mines

Energy Technology Data Exchange (ETDEWEB)

Galushko, A.L.; Brusilovskiy, V.I.; Popov, I.I.

1979-01-01

Information letters about accidents in coal mines are systematically developed and sent to enterprises and organizations of the branch for practical use in preventive work on work protection and work safety. Information materials on advanced experience in prevention of accidents and traumatism are published in large quantities. Principal measures which have dramatically affected the reduction of the level of production traumatism are listed which merit dissemination in the branch. It is noted that the use of these means of propaganda of work safety makes it possible to improve preventive work on work safety and production sanitation in enterprises of the coal industry.

Assessment of Factors Associated with the Safety Depth of GV15 Yamen

Directory of Open Access Journals (Sweden)

Park Soo-Jung

2014-03-01

Full Text Available Objectives: Yamen is the fifteenth acupoint of the Governor Vessel Meridian (GV15. It is anatomically close to the medulla oblongata, so finding the safety depth of the acupoint is very important. However, few studies on the safety depth of GV15 have been done. Methods: This study tried to measure the safety depth of GV15 by using magnetic resonance imaging (MRI scans and to analyze the factors affecting the safety depth through multiple regression analyses. This study was carried out for patients who had a brain MRI scan while visiting Jeonju Wonkwang Hospital, Korea. The shortest distance between the glabella and the occipital protuberance (DGO, the horizontal distance between the glabella and the back of the head (DGB and the dangerous depth (DD were measured from the sagittal views of the MRI images. The DD is the horizontal distance from the skin’s surface at GV15 to the spinal dura mater. Results: The model suggested that the safety depth (SD was significantly associated with gender (β = 0.474, P < 0.0001, DGO (β = 0.272, P = 0.027, and BMI (β = 0.249, P = 0.005 and the combination of three variables can explain the SD, with R2 = 0.571 (Table 3 A longer SD was associated with males and with greater BMI and DGO. Conclusion: This study suggests that gender, BMI and DGO may be important factors when the SD of GV15 is considered clinically through a multiple regression analysis of GV15.

Radiation Safety of Electromagnetic Waves

International Nuclear Information System (INIS)

Hussein, A.Z.

2009-01-01

The wide spread of Electromagnetic Waves (EMW) through the power lines, multimedia, communications, devices, appliances, etc., are well known. The probable health hazards associated with EMW and the radiation safety criteria are to be reviewed. However, the principles of the regulatory safety are based on radiation protection procedure, intervention to combat the relevant risk and to mitigate consequences. The oscillating electric magnetic fields (EMF) of the electromagnetic radiation (EMR) induce electrical hazards. The extremely high power EMR can cause fire hazards and explosions of pyrotechnic (Rad Haz). Biological hazards of EMF result as dielectric heat, severe burn, as well as the hazards of eyes. Shielding is among the technical protective measures against EMR hazards. Others are limitation of time of exposure and separation distance apart of the EMR source. Understanding and safe handling of the EMR sources are required to feel safety.

Recognizing Prefixes in Scientific Quantities

Science.gov (United States)

Sokolowski, Andrzej

2015-01-01

Although recognizing prefixes in physical quantities is inherent for practitioners, it might not be inherent for students, who do not use prefixes in their everyday life experiences. This deficiency surfaces in AP Physics exams. For example, readers of an AP Physics exam reported "a common mistake of incorrectly converting nanometers to…

The prospect of food irradiation and the contribution of radiation chemistry to enact the hygienic safety standard of irradiated foods

International Nuclear Information System (INIS)

Wu Jilan; Yuan Rongyao

1986-01-01

Now, it is said that we are at the dawn of food irradiation application both nationally and internationally. However, referring to the acceptability of customers the labeling of irradiated foods has been a nightmare to the food processors. On the other hand the recommended international standard has the shortcomings of thinking in absolute terms. In this paper a proposal which puts special emphasis on enacting hygienic safety standard of individual irradiated food is recommended. The hygienic safety standard of the irradiated food may be classified in three classes: 1) its hygienic safety standard is similar to that of common food; 2) the maximum permissible quantities of harmful compounds induced by radiation must be controlled; and 3) the quantity of unique radiolysis products may by dutermined. Radiation chemistry plays an important role in enacting the hygienic safety standard of irradiated foods. For international cooperation in this field some suggestions are made

30 CFR 75.322 - Harmful quantities of noxious gases.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Harmful quantities of noxious gases. 75.322... quantities of noxious gases. Concentrations of noxious or poisonous gases, other than carbon dioxide, shall... Governmental Industrial Hygienists in “Threshold Limit Values for Substance in Workroom Air” (1972). Detectors...

48 CFR 52.217-6 - Option for Increased Quantity.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 2 2010-10-01 2010-10-01 false Option for Increased....217-6 Option for Increased Quantity. As prescribed in 17.208(d), insert a clause substantially the same as the following: Option for Increased Quantity (MAR 1989) The Government may increase the...

41 CFR 109-27.102 - Economic order quantity principle.

Science.gov (United States)

2010-07-01

... PROCUREMENT 27-INVENTORY MANAGEMENT 27.1-Stock Replenishment § 109-27.102 Economic order quantity principle. ... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Economic order quantity principle. 109-27.102 Section 109-27.102 Public Contracts and Property Management Federal Property...

The Radiation Safety Culture: Image Gently

International Nuclear Information System (INIS)

Applegate, E.K.

2015-01-01

Barriers to Implementing Safety include Silos of Knowledge, Time, training and Resources. Creating a Safety Culture in Healthcare include Decreased authority gradients, Checklists and audits (QA), Use of structured language (SBAR), Situation, Background, Assessment, Recommendation Team briefings and debriefings (immediate learning, team building tools), Lifelong learning (PQI). Use of Collective Learning Opportunities - QA and PQI that include Web sites: IG, WFPI, IAEA, ISR and Data Registries: ACR . The Key Principles of Radiation Protection: When do we learn them? For Occupational Workers:Time, Distance and Shielding while those of For Patients: Justification, Optimization and Dose Limits (dose reference levels)

The Distance Standard Deviation

OpenAIRE

Edelmann, Dominic; Richards, Donald; Vogel, Daniel

2017-01-01

The distance standard deviation, which arises in distance correlation analysis of multivariate data, is studied as a measure of spread. New representations for the distance standard deviation are obtained in terms of Gini's mean difference and in terms of the moments of spacings of order statistics. Inequalities for the distance variance are derived, proving that the distance standard deviation is bounded above by the classical standard deviation and by Gini's mean difference. Further, it is ...

Distance Education in Turkey

Directory of Open Access Journals (Sweden)

Dr. Nursel Selver RUZGAR,

2004-04-01

Full Text Available Distance Education in Turkey Assistant Professor Dr. Nursel Selver RUZGAR Technical Education Faculty Marmara University, TURKEY ABSTRACT Many countries of the world are using distance education with various ways, by internet, by post and by TV. In this work, development of distance education in Turkey has been presented from the beginning. After discussing types and applications for different levels of distance education in Turkey, the distance education was given in the cultural aspect of the view. Then, in order to create the tendencies and thoughts of graduates of Higher Education Institutions and Distance Education Institutions about being competitors in job markets, sufficiency of education level, advantages for education system, continuing education in different Institutions, a face-to-face survey was applied to 1284 graduates, 958 from Higher Education Institutions and 326 from Distance Education Institutions. The results were evaluated and discussed. In the last part of this work, suggestions to become widespread and improve the distance education in the country were made.

Photosynthesis-related quantities for education and modeling.

Science.gov (United States)

Antal, Taras K; Kovalenko, Ilya B; Rubin, Andrew B; Tyystjärvi, Esa

2013-11-01

A quantitative understanding of the photosynthetic machinery depends largely on quantities, such as concentrations, sizes, absorption wavelengths, redox potentials, and rate constants. The present contribution is a collection of numbers and quantities related mainly to photosynthesis in higher plants. All numbers are taken directly from a literature or database source and the corresponding reference is provided. The numerical values, presented in this paper, provide ranges of values, obtained in specific experiments for specific organisms. However, the presented numbers can be useful for understanding the principles of structure and function of photosynthetic machinery and for guidance of future research.

Realism in nuclear criticality safety

International Nuclear Information System (INIS)

McLaughlin, T. P.

2009-01-01

Commercial nuclear power plant operation and regulation have made remarkable progress since the Three Mile Island Accident. This is attributed largely to a heavy dose of introspection and self-regulation by the industry and to a significant infusion of risk-informed and performance-based regulation by the Nuclear Regulatory Commission. This truly represents reality in action both by the plant operators and the regulators. On the other hand, the implementation of nuclear criticality safety in ex-reactor operations involving significant quantities of fissile material has not progressed, but, tragically, it has regressed. Not only is the practice of the discipline in excess of a factor of ten more expensive than decades ago; the trend continues. This unfortunate reality is attributed to a lack of coordination within the industry (as contrasted to what occurred in the reactor operations sector), and to a lack of implementation of risk-informed and performance-based regulation by the NRC While the criticality safety discipline is orders of magnitude smaller than the reactor safety discipline, both operators and regulators must learn from the progress made in reactor safety and apply it to the former to reduce the waste, inefficiency and potentially increased accident risks associated with current practices. Only when these changes are made will there be progress made toward putting realism back into nuclear criticality safety. (authors)

Report on transparency and nuclear safety 2015 - Saclay

International Nuclear Information System (INIS)

2016-06-01

This document proposes, first, a presentation of the Saclay CEA centre, of its activities and installations. Then it gives a rather detailed overview of measures related to safety and to radiation protection within these activities and installations. Next, it reports significant events related to safety and to radiation protection which occurred in 2015 and which have been declared to the French nuclear safety authority (ASN). It discusses the results of release measurements (liquid and gaseous effluents, radiological assessment, and chemical assessment for various installations) and the control of the chemical and radiological impact of these gaseous and liquid effluents on the environment. Finally, it addresses the issue of radioactive wastes which are stored in the different nuclear base installations of the Centre. It indicates the different measures aimed at limiting the volume of these warehoused wastes and addresses their impact on health and environment. Nature and quantities of warehoused wastes are specified. Remarks and recommendations of the Health, Safety and Working Conditions Committee (CHSCT) are given

Report on transparency and nuclear safety 2015 - Grenoble

International Nuclear Information System (INIS)

2016-06-01

This document proposes, first, a presentation of the Grenoble CEA centre, of its activities and installations. Then it gives a rather detailed overview of measures related to safety and to radiation protection within these activities and installations. Next, it reports significant events related to safety and to radiation protection which occurred in 2015 and which have been declared to the French nuclear safety authority (ASN). It discusses the results of release measurements (liquid and gaseous effluents, radiological assessment, and chemical assessment for various installations) and the control of the chemical and radiological impact of these gaseous and liquid effluents on the environment. Finally, it addresses the issue of radioactive wastes which are stored in the different nuclear base installations of the Centre. It indicates the different measures aimed at limiting the volume of these warehoused wastes and addresses their impact on health and environment. Nature and quantities of warehoused wastes are specified. Remarks and recommendations of the Health, Safety and Working Conditions Committee (CHSCT) are given

Category 3 threshold quantities for hazard categorization of nonreactor facilities

International Nuclear Information System (INIS)

Mandigo, R.L.

1996-01-01

This document provides the information necessary to determine Hazard Category 3 threshold quantities for those isotopes of interest not listed in WHC-CM-4-46, Section 4, Table 1.''Threshold Quantities.''

Criteria for development of a database for safety evaluation of fragrance ingredients.

Science.gov (United States)

Ford, R A; Domeyer, B; Easterday, O; Maier, K; Middleton, J

2000-04-01

Over 2000 different ingredients are used in the manufacture of fragrances. The majority of these ingredients have been used for many decades. Despite this long history of use, all of these ingredients need continued monitoring to ensure that each ingredient meets acceptable safety standards. As with other large databases of existing chemicals, fulfilling this need requires an organized approach to identify the most important potential hazards. One such approach, specifically considering the dermal route of exposure as the most relevant one for fragrance ingredients, has been developed. This approach provides a rational selection of materials for review and gives guidance for determining the test data that would normally be considered necessary for the elevation of safety under intended conditions of use. As a first step, the process takes into account the following criteria: quantity of use, consumer exposure, and chemical structure. These are then used for the orderly selection of materials for review with higher quantity, higher exposure, and the presence of defined structural alerts all contributing to a higher priority for review. These structural alerts along with certain exposure and volume limits are then used to develop guidelines for determining the quality and quantity of data considered necessary to support an adequate safety evaluation of the chosen materials, taking into account existing data on the substance itself as well as on closely related analogs. This approach can be considered an alternative to testing; therefore, it is designed to be conservative but not so much so as to require excessive effort when not justified.

19 CFR 144.33 - Minimum quantities to be withdrawn.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Minimum quantities to be withdrawn. 144.33 Section 144.33 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT... Warehouse § 144.33 Minimum quantities to be withdrawn. Unless by special authority of the Commissioner of...

Quantity Estimation Of The Interactions

International Nuclear Information System (INIS)

Gorana, Agim; Malkaj, Partizan; Muda, Valbona

2007-01-01

In this paper we present some considerations about quantity estimations, regarding the range of interaction and the conservations laws in various types of interactions. Our estimations are done under classical and quantum point of view and have to do with the interaction's carriers, the radius, the influence range and the intensity of interactions

Information quantity in a pixel of digital image

OpenAIRE

Kharinov, M.

2014-01-01

The paper is devoted to the problem of integer-valued estimating of information quantity in a pixel of digital image. The definition of an integer estimation of information quantity based on constructing of the certain binary hierarchy of pixel clusters is proposed. The methods for constructing hierarchies of clusters and generating of hierarchical sequences of image approximations that minimally differ from the image by a standard deviation are developed. Experimental results on integer-valu...

Processing ordinality and quantity: the case of developmental dyscalculia.

Directory of Open Access Journals (Sweden)

Orly Rubinsten

Full Text Available In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1 the traditionally and well accepted numerical magnitude system but also (2 core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD. Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1 and 3 numbers (symbolic task: Experiment 2. In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks, DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

Processing ordinality and quantity: the case of developmental dyscalculia.

Science.gov (United States)

Rubinsten, Orly; Sury, Dana

2011-01-01

In contrast to quantity processing, up to date, the nature of ordinality has received little attention from researchers despite the fact that both quantity and ordinality are embodied in numerical information. Here we ask if there are two separate core systems that lie at the foundations of numerical cognition: (1) the traditionally and well accepted numerical magnitude system but also (2) core system for representing ordinal information. We report two novel experiments of ordinal processing that explored the relation between ordinal and numerical information processing in typically developing adults and adults with developmental dyscalculia (DD). Participants made "ordered" or "non-ordered" judgments about 3 groups of dots (non-symbolic numerical stimuli; in Experiment 1) and 3 numbers (symbolic task: Experiment 2). In contrast to previous findings and arguments about quantity deficit in DD participants, when quantity and ordinality are dissociated (as in the current tasks), DD participants exhibited a normal ratio effect in the non-symbolic ordinal task. They did not show, however, the ordinality effect. Ordinality effect in DD appeared only when area and density were randomized, but only in the descending direction. In the symbolic task, the ordinality effect was modulated by ratio and direction in both groups. These findings suggest that there might be two separate cognitive representations of ordinal and quantity information and that linguistic knowledge may facilitate estimation of ordinal information.

Haptic Discrimination of Distance

Science.gov (United States)

van Beek, Femke E.; Bergmann Tiest, Wouter M.; Kappers, Astrid M. L.

2014-01-01

While quite some research has focussed on the accuracy of haptic perception of distance, information on the precision of haptic perception of distance is still scarce, particularly regarding distances perceived by making arm movements. In this study, eight conditions were measured to answer four main questions, which are: what is the influence of reference distance, movement axis, perceptual mode (active or passive) and stimulus type on the precision of this kind of distance perception? A discrimination experiment was performed with twelve participants. The participants were presented with two distances, using either a haptic device or a real stimulus. Participants compared the distances by moving their hand from a start to an end position. They were then asked to judge which of the distances was the longer, from which the discrimination threshold was determined for each participant and condition. The precision was influenced by reference distance. No effect of movement axis was found. The precision was higher for active than for passive movements and it was a bit lower for real stimuli than for rendered stimuli, but it was not affected by adding cutaneous information. Overall, the Weber fraction for the active perception of a distance of 25 or 35 cm was about 11% for all cardinal axes. The recorded position data suggest that participants, in order to be able to judge which distance was the longer, tried to produce similar speed profiles in both movements. This knowledge could be useful in the design of haptic devices. PMID:25116638

Haptic discrimination of distance.

Directory of Open Access Journals (Sweden)

Femke E van Beek

Full Text Available While quite some research has focussed on the accuracy of haptic perception of distance, information on the precision of haptic perception of distance is still scarce, particularly regarding distances perceived by making arm movements. In this study, eight conditions were measured to answer four main questions, which are: what is the influence of reference distance, movement axis, perceptual mode (active or passive and stimulus type on the precision of this kind of distance perception? A discrimination experiment was performed with twelve participants. The participants were presented with two distances, using either a haptic device or a real stimulus. Participants compared the distances by moving their hand from a start to an end position. They were then asked to judge which of the distances was the longer, from which the discrimination threshold was determined for each participant and condition. The precision was influenced by reference distance. No effect of movement axis was found. The precision was higher for active than for passive movements and it was a bit lower for real stimuli than for rendered stimuli, but it was not affected by adding cutaneous information. Overall, the Weber fraction for the active perception of a distance of 25 or 35 cm was about 11% for all cardinal axes. The recorded position data suggest that participants, in order to be able to judge which distance was the longer, tried to produce similar speed profiles in both movements. This knowledge could be useful in the design of haptic devices.

A Generalized Pivotal Quantity Approach to Analytical Method Validation Based on Total Error.

Science.gov (United States)

Yang, Harry; Zhang, Jianchun

2015-01-01

The primary purpose of method validation is to demonstrate that the method is fit for its intended use. Traditionally, an analytical method is deemed valid if its performance characteristics such as accuracy and precision are shown to meet prespecified acceptance criteria. However, these acceptance criteria are not directly related to the method's intended purpose, which is usually a gurantee that a high percentage of the test results of future samples will be close to their true values. Alternate "fit for purpose" acceptance criteria based on the concept of total error have been increasingly used. Such criteria allow for assessing method validity, taking into account the relationship between accuracy and precision. Although several statistical test methods have been proposed in literature to test the "fit for purpose" hypothesis, the majority of the methods are not designed to protect the risk of accepting unsuitable methods, thus having the potential to cause uncontrolled consumer's risk. In this paper, we propose a test method based on generalized pivotal quantity inference. Through simulation studies, the performance of the method is compared to five existing approaches. The results show that both the new method and the method based on β-content tolerance interval with a confidence level of 90%, hereafter referred to as the β-content (0.9) method, control Type I error and thus consumer's risk, while the other existing methods do not. It is further demonstrated that the generalized pivotal quantity method is less conservative than the β-content (0.9) method when the analytical methods are biased, whereas it is more conservative when the analytical methods are unbiased. Therefore, selection of either the generalized pivotal quantity or β-content (0.9) method for an analytical method validation depends on the accuracy of the analytical method. It is also shown that the generalized pivotal quantity method has better asymptotic properties than all of the current

Foreign materials in the repository. Update of estimated quantities

International Nuclear Information System (INIS)

Karvonen, T.

2011-06-01

A variety of materials are used during the construction process and the operation of the repository for spent nuclear fuel at Olkiluoto in Eurajoki, Finland. In addition to materials necessary for the construction and operation, some materials may be transported into the repository with the ventilation air, as emissions from vehicles etc. Both of these two types of materials are considered here and both introduced quantities and the quantities that remain after the closure in the repository are estimated here based on the most recent information. This work is intended to update the previous estimations, and it takes advantage of the experience collected during the construction of the underground rock characterisation facility called ONKALO at Olkiluoto. The implemented quantities as well as designs and preliminary designs have been used in calculating the quantities of the foreign materials. The estimations made in this report are specific to a KBS-3V type repository. In some cases more generic information has been used, particularly when the relevant quantities have not been monitored in ONKALO. The estimations are based on the new repository layout produced in 2010 and consider the latest plans for grouting and rock support. As all of these plans are not final some quantities may change in the future. As the repository layout may still go through some changes this report also provides the foreign materials for a hundred meters of different deposition tunnels designed for the OL and LO type canisters1. The results have also been calculated for a space demanded by a deposition tunnel end plug and the tunnel lengths before and after one. The most significant foreign materials are certain accessory minerals of the clay materials followed by organic materials (including the organic carbon from the clay materials), cement, steel and silica. (orig.)

Inherent and passive safety measures in accelerator driven systems: a safety strategy for ADS

International Nuclear Information System (INIS)

Maschek, W.; Rineiski, A.; Morita, K.; Flad, M.

2001-01-01

The efficiency of Accelerator Driven Systems (ADSs) for the transmutation and incineration of nuclear waste is strongly related to the utilization of so-called dedicated fuels. In the ideal case these fuels should consist of pure TRUs without fertile materials as 238 U or 232 Th to achieve highest incineration/transmutation rates. Dedicated fuels still have to be developed and programs are under way for their fabrication, irradiation and testing. These fertile-free fuels may suffer from deteriorated thermal or thermo-mechanical properties, as a reduced melting point, reduced thermal conductivity or even thermal instability. First analyses have shown that the use of dedicated fuels may lead to a strong deterioration of the safety parameters of the reactor core as e.g. the void worth, the Doppler or the kinetics quantities as neutron generation time and β eff . In addition, a dedicated core may contain multiple ''critical'' fuel masses, resulting in a considerable recriticality potential. Current knowledge on these dedicated fuels suggests that ''critical'' reactors may not be feasible, because of safety reasons. However, for ADSs, the salient hope has been promoted that due to the subcriticality of the system the poor safety features of such fuels could be coped with. Analyses are presented which show potential safety problems for such dedicated cores. Respecting the results of these analyses a safety strategy is proposed along the lines of defense approach in analogy with ideas formerly developed for fast reactors. Inherent and passive safety measures are integrated into the various defense lines. (author)

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-01-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosimeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The U.S. personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethylmethacrylate (PMMA) phantom; therefore it is necessary to relate the response of dosimeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosimeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors. (author)

Calibration of personal dosemeters in terms of the ICRU operational quantities

International Nuclear Information System (INIS)

McDonald, J.C.; Hertel, N.E.

1992-05-01

The International Commission on Radiological Units and Measurements (ICRU) has defined several new operational quantities for radiation protection purposes. The quantities to be used for personal monitoring are defined at depths in the human body. Because these quantities are impossible to measure directly, the ICRU has recommended that personal dosemeters should be calibrated under simplified conditions on an appropriate phantom, such as the ICRU sphere. The US personal dosimetry accreditation programs make use of a 30 x 30 x 15 cm polymethymethacrylate (PMMA) phantom, therefore it is necessary to relate the response of dosemeters calibrated on this phantom to the ICRU operational quantities. Calculations of the conversion factors to compute dosemeter response in terms of the operational quantities have been performed using the code MCNP. These calculations have also been compared to experimental measurements using thermoluminescent (TLD) detectors

Guidelines for selecting preferred highway routes for highway-route-controlled quantity shipments of radioactive materials

International Nuclear Information System (INIS)

1989-01-01

The document presents guidelines for use by State officials in selecting preferred routes for highway route controlled quantity shipments of radioactive materials. A methodology for analyzing and comparing safety factors of alternative routes is described. Technical information on the impacts of radioactive material transportation needed to apply the methodology is also presented. Application of the methodology will identify the route (or set of routes) that minimizes the radiological impacts from shipments of these radioactive materials within a given State. Emphasis in the document is on practical application of the methodology. Some details of the derivation of the methods and data are presented in the appendices. All references in the body of the report can be found listed in the Bibliography (Appendix F)

An investigation of safety attitude in a number of manufacturing companies in Urmia

Directory of Open Access Journals (Sweden)

Abolfazl Ghahramani

2016-12-01

Result: The results indicated that majority of participants (78.9 % had a moderate safety attitude level and the mean (±SD score of total safety attitude was 3.19 (±0.25. “Commitment to safety and participation in safety activities” and “safety talk and risk information communication” obtained the highest and lowest scores of safety attitude factors, with mean (SD of 3.97(±0.52 and 2.53(±0.58, respectively. In addition, the participants from private companies showed a better safety attitude than those of governmental companies (P-value<0.05. Managers and workers, who had previously received safety training, reported a different attitude toward various factors of safety attitude, in comparison with untrained groups. Conclusion: Since the majority of participants had a moderate safety attitude, this research suggests the study companies to attempt in order to increase the quantity and quality of safety training courses, as well as safety communication of managers and supervisors with workers for improving their attitude toward safety and subsequently decreasing occupational accidents.

Mine Ventilation System Variable Resistance Regulate Air Quantity Economy and Its Impacts on Artisanal Mine in Ivory Coast

Directory of Open Access Journals (Sweden)

Kouame Kouame Arthur Joseph

2016-01-01

Full Text Available The artisanal gold mining is one of the major illegal activities in Ivory Coast. Thousands of indigents and foreigners including men, women and children are involved in this dangerous activity. Contracting contagious diseases such as HIV/AIDS and multiple lung diseases are commonplace on the artisanal mining sites due to air pollution. For this reason, the differential analysis, research mine ventilation system by changing the working windage adjustment for air flow of the economy, identifies factors, obtained discriminant variable resistance air volume control economic quantitative criteria for underground actual situation of joint variable resistance method and economic variable resistance than the concept of the development of effective mine ventilation system to improve air quantity adjusting rheostat economical way. The findings of this study can help lead to better safety practices in mining in order to improve the health and safety of the miners who are involved in artisanal mining activities in Ivory Coast and other mining sites over the world.

Conserved quantities for generalized KdV equations

International Nuclear Information System (INIS)

Calogero, F.; Rome Univ.; Degasperis, A.; Rome Univ.

1980-01-01

It is noted that the nonlinear evolution equation usub(t) = α(t)usub(xxx) - 6ν(t) usub(x)u, u is identical to u(x,t), possesses three (and, in some cases, four) conserved quantities, that are explicitly displayed. These results are of course relevant only to the cases in which this evolution equation is not known to possess an infinite number of conserved quantities. Purpose and scope of this paper is to report three or four simple conservation laws possessed by the evolution equation usub(t) = α(t)usub(xxx) - 6ν(t)usub(x)u, u is identical to u(x,t). (author)

A geochemical module for "AMDTreat" to compute caustic quantity, effluent quantity, and sludge volume

Science.gov (United States)

Cravotta,, Charles A.; Parkhurst, David L.; Means, Brent P; McKenzie, Bob; Morris, Harry; Arthur, Bill

2010-01-01

Treatment with caustic chemicals typically is used to increase pH and decrease concentrations of dissolved aluminum, iron, and/or manganese in largevolume, metal-laden discharges from active coal mines. Generally, aluminum and iron can be removed effectively at near-neutral pH (6 to 8), whereas active manganese removal requires treatment to alkaline pH (~10). The treatment cost depends on the specific chemical used (NaOH, CaO, Ca(OH)2, Na2CO3, or NH3) and increases with the quantities of chemical added and sludge produced. The pH and metals concentrations do not change linearly with the amount of chemical added. Consequently, the amount of caustic chemical needed to achieve a target pH and the corresponding effluent composition and sludge volume can not be accurately determined without empirical titration data or the application of geochemical models to simulate the titration of the discharge water with caustic chemical(s). The AMDTreat computer program (http://amd.osmre.gov/ ) is widely used to compute costs for treatment of coal-mine drainage. Although AMDTreat can use results of empirical titration with industrial grade caustic chemicals to compute chemical costs for treatment of net-acidic or net-alkaline mine drainage, such data are rarely available. To improve the capability of AMDTreat to estimate (1) the quantity and cost of caustic chemicals to attain a target pH, (2) the concentrations of dissolved metals in treated effluent, and (3) the volume of sludge produced by the treatment, a titration simulation is being developed using the geochemical program PHREEQC (wwwbrr.cr.usgs.gov/projects/GWC_coupled/phreeqc/) that will be coupled as a module to AMDTreat. The simulated titration results can be compared with or used in place of empirical titration data to estimate chemical quantities and costs. This paper describes the development, evaluation, and potential utilization of the PHREEQC titration module for AMDTreat.

Nuclear safety and radiation protection report of the nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the Tricastin operational hot base facility (INB no. 157, Bollene, Vaucluse (FR)), a nuclear workshop for storage and maintenance and qualification operations on some EdF equipments. Then, the nuclear safety and radiation protection measures taken regarding the facility are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if some, are reported as well as the effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility is presented and sorted by type of waste, quantities and type of conditioning. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

International Nuclear Information System (INIS)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun; Sung, Nak-Hoon; Jung, Seung Hyuk

2016-01-01

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis

Establishment and Evaluation of Decommissioning Plant Inventory DB and Waste Quantity

Energy Technology Data Exchange (ETDEWEB)

Oh, Jae Yong; Moon, Sang-Rae; Yun, Taesik; Kim, Hee-Geun [KHNP CRI, Daejeon (Korea, Republic of); Sung, Nak-Hoon; Jung, Seung Hyuk [KONES Corp., Seoul (Korea, Republic of)

2016-10-15

Korea Hydro and Nuclear Power (KHNP) made a decision for permanent shutdown of Kori-1 and has progressed the strategy determination and R and D for the decommissioning of Kori-1. Decommissioning waste, Structure, System and Components (SSCs) is one of the most important elements. Decommissioning waste quantity is calculated based on Plant Inventory Database (PI DB) with activation and contamination data. Due to the largest portion of waste management and disposal in decommissioning, it is necessary to exactly evaluate waste quantity (applying the regulation, guideline and site-specific characterization) for economic feasibility. In this paper, construction of PI DB and evaluation of waste quantity for Optimized Pressurized Reactor (OPR-1000) are mainly described. Decommissioning waste quantities evaluated are going to be applied to calculation of the project cost. In fact, Ministry of Trade, Industry and Energy (MOTIE) in Korea expected the decommissioning waste quantity in a range of 14,500-18,850 drums, and predicted appropriate liability for decommissioning fund by using waste quantity. The result of this study is also computed by the range of 14,500-18,850 drums. Since there is no site-specific data for the NPP site, this evaluation is the preliminary analysis.

HySTAR: the hydrogen safety training and risk workplace

International Nuclear Information System (INIS)

Hay, R.

2006-01-01

This paper shows the output of the software package HySTAR, the Hydrogen Safety, Training and Risk Workplace. This is the software output of the CTFA, Canadian Hydrogen Safety Program projects. It shows the Hydrogen Virtual Interactive Expert Workplace, a guide for permitting and code enforcement for officials and other parties involved in approving hydrogen energy facilities. It also shows the Hydrogen Codes and Standards Report (Site Level) as well as Hydrogen Distances and Clearances Report

29 CFR 780.814 - “Grown in commercial quantities.”

Science.gov (United States)

2010-07-01

... OF GENERAL POLICY OR INTERPRETATION NOT DIRECTLY RELATED TO REGULATIONS EXEMPTIONS APPLICABLE TO AGRICULTURE, PROCESSING OF AGRICULTURAL COMMODITIES, AND RELATED SUBJECTS UNDER THE FAIR LABOR STANDARDS ACT... “commercial” quantities, the trade understanding of what are “commercial” quantities of cotton would be...

Distancing from experienced self: how global-versus-local perception affects estimation of psychological distance.

Science.gov (United States)

Liberman, Nira; Förster, Jens

2009-08-01

In 4 studies, the authors examined the prediction derived from construal level theory (CLT) that higher level of perceptual construal would enhance estimated egocentric psychological distance. The authors primed participants with global perception, local perception, or both (the control condition). Relative to the control condition, global processing made participants estimate larger psychological distances in time (Study 1), space (Study 2), social distance (Study 3), and hypotheticality (Study 4). Local processing had the opposite effect. Consistent with CLT, all studies show that the effect of global-versus-local processing did emerge when participants estimated egocentric distances, which are distances from the experienced self in the here and now, but did not emerge with temporal distances not from now (Study 1), spatial distances not from here (Study 2), social distances not from the self (Study 3), or hypothetical events that did not involve altering an experienced reality (Study 4).

Fire safety study of Dodewaard and Borssele nuclear power plants

International Nuclear Information System (INIS)

1988-03-01

From the nuclear and conventional fire safety audits of both Dutch nuclear power plants performed under supervision of the Nuclear Safety Inspectorate and the Inspectorate for the Fire Services it turns out that the fire safety is sufficient however amenable for improvement. Besides a detailed description of the method of examination, the study 'Fire Safety' contains the results of the audit and 14 respectively 15 recommendations for improvement of the fire safety in Dodewaard and Borssele. The suggested recommendations which are applicable to both power plants are the following: fire fighting training for operators and guards, a complete emergency ventilation system of the control room, increase in the number of detectors and alarms, an increase in the quantity of water available for high-pressure fire fighting, improvement of fire barriers between several redundancies of nuclear safety systems, an investigation and possible improvement of the heat and radiation protection offered by presently used fire fighting suits. For Dodewaard a closed emergency staircase in the reactor building (secondary containment) is deemed necessary for personnel emergency escape routes and continued fire fighting if required

Fast Computing for Distance Covariance

OpenAIRE

Huo, Xiaoming; Szekely, Gabor J.

2014-01-01

Distance covariance and distance correlation have been widely adopted in measuring dependence of a pair of random variables or random vectors. If the computation of distance covariance and distance correlation is implemented directly accordingly to its definition then its computational complexity is O($n^2$) which is a disadvantage compared to other faster methods. In this paper we show that the computation of distance covariance and distance correlation of real valued random variables can be...

ORDERED WEIGHTED DISTANCE MEASURE

Institute of Scientific and Technical Information of China (English)

Zeshui XU; Jian CHEN

2008-01-01

The aim of this paper is to develop an ordered weighted distance (OWD) measure, which is thegeneralization of some widely used distance measures, including the normalized Hamming distance, the normalized Euclidean distance, the normalized geometric distance, the max distance, the median distance and the min distance, etc. Moreover, the ordered weighted averaging operator, the generalized ordered weighted aggregation operator, the ordered weighted geometric operator, the averaging operator, the geometric mean operator, the ordered weighted square root operator, the square root operator, the max operator, the median operator and the min operator axe also the special cases of the OWD measure. Some methods depending on the input arguments are given to determine the weights associated with the OWD measure. The prominent characteristic of the OWD measure is that it can relieve (or intensify) the influence of unduly large or unduly small deviations on the aggregation results by assigning them low (or high) weights. This desirable characteristic makes the OWD measure very suitable to be used in many actual fields, including group decision making, medical diagnosis, data mining, and pattern recognition, etc. Finally, based on the OWD measure, we develop a group decision making approach, and illustrate it with a numerical example.

Determination of Quality and Quantity for Primary Schoolyards in Artvin City Center By Using Geographical Information System

Directory of Open Access Journals (Sweden)

Emine Arslan Muhacir

2011-11-01

Full Text Available Rapid increase in concretion rate and a related decrease in the amount of public-green areas per capita have become an important issue for people living in cities. Children that are stuck in between tall buildings and have longing for play are the most affected ones from this issue. Adequateness of schoolyards both in quality and quantity is very important for physical and mental development of children especially for those attending primary schools and spending the most of their time in schoolyards. This importance has revealed not only the issue of increasing the quality of school buildings but also the necessity of better outdoor spaces for schools in order to have more successful education period. Moreover, some criterions such as distance, density and population should be taken into account when determining education areas in local zoning legislation. Even though it is assumed that every city has optimal social, topographical and other similar features for application of planning principles, these are not applicable for many cities such as Artvin due to its rugged land formation and irregular urbanization. The main objective of this study was to evaluate schoolyards in Artvin by stating their current status in Artvin both in quality and quantity aspects, since both have important effects on child’s physical and mental development.

Substantiation of the radiation monitoring scope in the region of nuclear power plant location

Energy Technology Data Exchange (ETDEWEB)

Zykova, A S; Zhakov, Yu A; Yambrovskii, Ya M

1977-12-01

To provide radiation safety of the population in the region of nuclear power plant location, it is necessary to define the character and quantity of radiation monitoring. On the basis of radiation monitoring of effluents from operating nuclear power plants it is found that the effluents can be registered at a distance of 5-7 km from the plant. The quantity of sample analysis of the main enviromental objectives must provide an exact definition of the content of radioactive substances produced by radioactive fallouts and effluents from nuclear power plants.

Substantiation of the radiation monitoring scope in the region of nuclear power plant location

International Nuclear Information System (INIS)

Zykova, A.S.; Zhakov, Yu.A.; Jambrovskij, Ya.M.

1977-01-01

To provide radiation safety of the population in the region of nuclear power plant location, it is necessary to define the character and quantity of radiation monitoring. On the basis of radiation monitoring of flowouts from operating nuclear power plants it is found that the flowouts can be registered at a distance of 5-7 km from the plant. The quantity of sample analysis of the main enviromental objectives must provide an exact definition of the content of radioactive substances produced by radioactive fallouts and flowouts from nuclear power plants

Radiation quantities and units. ICRU report 33

International Nuclear Information System (INIS)

Anon.

1987-01-01

This report supersedes ICRU Report 19. Since ICRU Report 19 was published, a number of discussions have taken place between members of the Report Committee on Fundamental Quantities and Units and other workers in the field. Some of these discussions have resulted in the acceptance of certain modifications in the material set out in Report 19 and these modifications are incorporated in the current report. In addition, there has been some expansion and rearrangement of the material in the earlier report. It is recommended that energy state be inserted into the definition of activity and that the word transformation be replaced by transition. These modifications have now been incorporated into the current definition. Helpful comments on the previous quantities and units report have resulted in clarification of several points in the present Report. In line with providing more didactic material and useful source material for other ICRU reports, the general considerations in subsection I.A of Report 19 have been expanded and placed in a separate subsection. The additional material includes discussions of four terms that are used in this document - quantity, unit, stochastic, and non-stochastic - along with a brief discussion of the mathematical formalism used in ICRU reports. 11 refs., 4 tabs

Trained Quantity Abilities in Horses (Equus caballus: A Preliminary Investigation

Directory of Open Access Journals (Sweden)

Maria Elena Miletto Petrazzini

2014-07-01

Full Text Available Once believed to be a human prerogative, the capacity to discriminate between quantities now has also been reported in several vertebrates. To date, only two studies investigated numerical abilities in horses (Equus caballus but reported contrasting data. To assess whether horses can be trained to discriminate between quantities, I have set up a new experimental protocol using operant conditioning. One adult female was trained to discriminate between 1 and 4 (Test 1 in three different conditions: non-controlled continuous variables (numerical and continuous quantities that co-vary with number are simultaneously available, 50% controlled continuous variables (intermediate condition, and 100% controlled continuous variables (only numerical information available. The subject learned the discrimination in all conditions, showing the capacity to process numerical information. When presented with a higher numerical ratio (2 vs. 4, Test 2, the subject still discriminated between the quantities but its performance was statistically significant only in the non-controlled condition, suggesting that the subject used multiple cues in presence of a more difficult discrimination. On the whole, the results here reported encourage the use of this experimental protocol as a valid tool to investigate the capacity to process numerical and continuous quantities in horses in future research.

On the Output-Inflation Relationship When Price and Quantity Adjustments are Costly

DEFF Research Database (Denmark)

Danziger, Leif; Kreiner, Claus Thustrup

A vast literature analyzes the real effects of price-adjustment costs assuming that quantity adjustments are costless. In this paper, we analyze whether the presence of quantity-adjustments costs, which presumably are significant, change the traditional results on the impact of inflation....... In particular, recent findings suggest that quantity-adjustment costs may remove the linkage between output and inflation. We show that this is not the case when inflation is anticipated. On the contrary, quantity-adjustment costs may significantly amplify the consequences of price-adjustment costs...

Study of dosimetric quantities and image quality in pediatric examinations of chest and abdomen computed tomography

International Nuclear Information System (INIS)

Jornada, Tiago da Silva

2013-01-01

This work had the objective to achieve the knowledge of the dosimetric quantities related to chest and abdomen computed tomography (CT) examinations of pediatric patients, in Belo Horizonte city. The reason of this work is based on the fact that the probability of health detriment in children, which it may be caused by radiation, is higher than in adults. Besides, although in many countries the knowledge and control of patient doses is a normal procedure, this safety culture does not exist in Brazil. Another objective of this work was to compare the dosimetric quantity values with the Diagnostic Reference Levels (DRLs); when it was needed, an optimization process was applied and the quality of the diagnostic image obtained with the optimized technical parameters was analyzed. This study was carried out in five hospitals, where the weighted air kerma index (Cw), the volumetric air kerma index (Cvol), the air kerma - length product (PKL,CT), the Effective Dose (E) and the Normalized Effective Dose (En) were determined; three methods were adopted for measurements: the ionization chamber inside a chest pediatric phantom, radiochromic films and the CT-EXPO software. The optimization process was applied to a single hospital through variations in the current (mA) and voltage (kV) of the x-ray tube for the protocols used for abdomen CT examinations. The analysis of the quality of the diagnostic image was done by Normal Distribution and ROC analysis; spatial resolution analysis was used through MTF determination and the noise level was judged in terms quantitative and qualitative. Results of the dosimetric quantities showed that they significantly differed between single-slice and multi-slice tomography units, but their values were always below the recommended DRLs. The optimized values of the dosimetric quantities obtained after the optimization process showed that it was possible to reduce the radiation exposure of pediatric patient without losing the image quality

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

Energy Technology Data Exchange (ETDEWEB)

Hagros, Annika (Sannio and Riekkola OY (Finland))

2008-12-15

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

Estimated quantities of residual materials in a KBS-3H repository at Olkiluoto

International Nuclear Information System (INIS)

Hagros, Annika

2008-12-01

The quantities of residual materials in a KBS-3H type repository have been estimated in this report. The repository is assumed to be constructed at Olkiluoto in Eurajoki, Western Finland. Both the total quantities of the materials introduced into the repository and the quantities of materials that remain in the repository after closure have been calculated. The calculations are largely based on a similar work regarding the material quantities in the Finnish KBS-3V repository and the main goal has been to identify the differences between the KBS-3H and KBS-3V repositories with respect to the type and quantities of residual materials. As the design of the KBS-3H repository is not final yet, the results are only preliminary. Several alternative designs were assumed in the calculations, resulting in different total quantities of materials. The design alternatives that had the greatest effect on the total material quantities were the two different tunnel backfill options, bentonite-crushed rock and Friedland clay. If Friedland clay is used instead of a bentonite-crushed rock mixture, the total quantity of pyrite remaining in the repository is 20 times larger and the quantities of organic materials and gypsum are also increased significantly. The other design alternatives did not have a substantial effect on the total material quantities. The remaining quantity of cement can be reduced by some 20% by selecting the silica grouting alternative in the sealing of the rock mass and low-pH cement in the shotcreting of the repository, instead of using the ordinary cement alternatives. If the total quantity of steel should be minimised, the use of the DAWE design alternative would be better than the Basic Design, although the total reduction would be less than 10%. The main difference between the different drift end plug alternatives is related to the total remaining quantity of silica, which is some 80% smaller if the rock plug is used instead of the LHHP (Low Heat High

Proposal of safety design methodologies for an HTGR-hydrogen production system. Mainly on countermeasures against fire and explosion

International Nuclear Information System (INIS)

Nishihara, Tetsuo; Hada, Kazuhiko; Shiozawa, Syusaku

1996-03-01

Among key issues of the safety design for an HTGR-hydrogen production system is to ensure the safety of the nuclear reactor against fire and explosion accidents in the hydrogen production plant. The fire and explosion accidents in the hydrogen production plant are categorized into the following two cases; Accidents inside the reactor building (R/B) and accidents outside the R/B. Against accidents inside the R/B, the proposed safety design concept is to prevent the occurrence of the accidents based on the defence in depth concept. The piping system and/or heat transfer tubes which have the potential possibility of combustible materials ingress into the R/B due to the failure are designed at the highest aseismic level to prevent the failure against severe earthquake. Even if the failure occurs, the piping trench and related compartments are fulfilled with nitrogen so as to prevent the occurrence of accidents. The proposed safety design concept for the accidents outside the R/B is the mitigation of effects of accidents. Proposed countermeasures is to take the safe distance between the hydrogen production plant and the items important to safety in the nuclear plant. We showed that the anticipated accidents to estimate the safe distance are large scale pool burning, fireball, pressure vessel burst and vapor cloud explosion. Especially, new estimating concept to establish the safe distance is proposed for the vapor cloud explosion. To reduce the safe distance, we proposed the underground non-pressurized storage tank and ventilation system for the storage of large amount of combustible liquid. (author). 61 refs

A statistical law in the perception of risks and physical quantities in traffic

DEFF Research Database (Denmark)

Elvik, Rune

2015-01-01

This paper suggests that a universal psychophysical law influences the perception of risks and physical quantities in traffic. This law states that there will be a tendency to overestimate low probabilities or small quantities, while high probabilities or large quantities may be underestimated....... Studies of the perception of risk and physical quantities in traffic have found a highly consistent pattern....

Study of LED modulation effect on the photometric quantities and beam homogeneity of automotive lighting

Science.gov (United States)

Koudelka, Petr; Hanulak, Patrik; Jaros, Jakub; Papes, Martin; Latal, Jan; Siska, Petr; Vasinek, Vladimir

2015-07-01

This paper discusses the implementation of a light emitting diode based visible light communication system for optical vehicle-to-vehicle (V2V) communications in road safety applications. The widespread use of LEDs as light sources has reached into automotive fields. For example, LEDs are used for taillights, daytime running lights, brake lights, headlights, and traffic signals. Future in the optical vehicle-to-vehicle (V2V) communications will be based on an optical wireless communication technology that using LED transmitter and a camera receiver (OCI; optical communication image sensor). Utilization of optical V2V communication systems in automotive industry naturally brings a lot of problems. Among them belongs necessity of circuit implementation into the current concepts of electronic LED lights control that allows LED modulation. These circuits are quite complicated especially in case of luxury cars. Other problem is correct design of modulation circuits so that final vehicle lightning using optical vehicle-to-vehicle (V2V) communication meets standard requirements on Photometric Quantities and Beam Homogeneity. Authors of this article performed research on optical vehicle-to-vehicle (V2V) communication possibilities of headlight (Jaguar) and taillight (Skoda) in terms of modulation circuits (M-PSK, M-QAM) implementation into the lamp concepts and final fulfilment of mandatory standards on Photometric Quantities and Beam Homogeneity.

Task Group on Safety Margins Action Plan (SMAP). Safety Margins Action Plan - Final Report

International Nuclear Information System (INIS)

Hrehor, Miroslav; Gavrilas, Mirela; Belac, Josef; Sairanen, Risto; Bruna, Giovanni; Reocreux, Michel; Touboul, Francoise; Krzykacz-Hausmann, B.; Park, Jong Seuk; Prosek, Andrej; Hortal, Javier; Sandervaag, Odbjoern; Zimmerman, Martin

2007-01-01

. Chapter 3 looks at techniques for the deterministic calculation of safety margins and discusses the complementary probabilistic risk assessment techniques needed to generalize safety margins beyond design basis accidents. Chapter 4 examines the definition of safety margin, which is noted to take different meanings in different fields. For example, in civil engineering and applications that deal with the load-strength interference concept, safety margin describes the distance between the means of the load and strength probability density functions with regard to the standard deviation in both. However, in the nuclear industry, the term safety margin evolved to describe the goal of assuring the existence of adequate safety margin in deterministic calculations. Specifically, safety margin refers to keeping the value of a given safety variable under a pre-established safety limit in design basis accidents. Implicitly, safety margin in the nuclear industry is the distance from the safety limit to onset of damage. The SMAP task group fulfilled its first objective by adopting a methodology for quantifying safety margins that merges the deterministic and probabilistic approaches. The methodology described in Chapter 5 is consistent with the definition of safety margin commonly used in the nuclear industry. The metrics of this methodology quantify the change in safety over a range of accident sequences that extend beyond the design bases. However, the methodology is not described in this report to a level that would meet guidance document requirements. This is in part because methods and techniques needed to quantify safety margins in a global manner are evolving, and thus specific guidance rendered at this time would shortly become obsolete. This report presents the framework in sufficient detail to serve as the basis of an analysis and, thus, this report meets the second objective established for the SMAP group. A proof-of-concept application to further aid potential applicants

Entropy and Its Correlations with Other Related Quantities

Directory of Open Access Journals (Sweden)

Jing Wu

2014-02-01

Full Text Available In order to find more correlations between entropy and other related quantities, an analogical analysis is conducted between thermal science and other branches of physics. Potential energy in various forms is the product of a conserved extensive quantity (for example, mass or electric charge and an intensive quantity which is its potential (for example, gravitational potential or electrical voltage, while energy in specific form is a dissipative quantity during irreversible transfer process (for example mechanical or electrical energy will be dissipated as thermal energy. However, it has been shown that heat or thermal energy, like mass or electric charge, is conserved during heat transfer processes. When a heat transfer process is for object heating or cooling, the potential of internal energy U is the temperature T and its potential “energy” is UT/2 (called entransy and it is the simplified expression of thermomass potential energy; when a heat transfer process is for heat-work conversion, the potential of internal energy U is (1 − T0/T, and the available potential energy of a system in reversible heat interaction with the environment is U − U0 − T0(S − S0, then T0/T and T0(S − S0 are the unavailable potential and the unavailable potential energy of a system respectively. Hence, entropy is related to the unavailable potential energy per unit environmental temperature for heat-work conversion during reversible heat interaction between the system and its environment. Entropy transfer, like other forms of potential energy transfer, is the product of the heat and its potential, the reciprocal of temperature, although it is in form of the quotient of the heat and the temperature. Thus, the physical essence of entropy transfer is the unavailable potential energy transfer per unit environmental temperature. Entropy is a non-conserved, extensive, state quantity of a system, and entropy generation in an irreversible heat transfer process

Import and export of small quantities of nuclear materials

International Nuclear Information System (INIS)

Grenier, M.

1986-06-01

Administrative procedures for import export of nuclear materials are specific for each country. In France regulations are reviewed for small quantities, lower threshold, in some cases, allows a simplified procedure, however thresholds are not the same in the different texts (and for one of them, concerning proliferation, is zero). It is obvious that regulations are necessary even for small quantities but national and international threshold should be harmonized [fr

7 CFR 35.13 - Minimum quantity.

Science.gov (United States)

2010-01-01

... 7 Agriculture 2 2010-01-01 2010-01-01 false Minimum quantity. 35.13 Section 35.13 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... part, transport or receive for transportation to any foreign destination, a shipment of 25 packages or...

The SHIELD (Safety & Health Improvement: Enhancing Law Enforcement Departments Study: Feasibility and Findings

Directory of Open Access Journals (Sweden)

Kerry Stephen Kuehl

2014-05-01

Full Text Available This randomized prospective trial aimed to assess the feasibility and efficacy of a team-based worksite health and safety intervention for law enforcement personnel. Four-hundred and eight subjects were enrolled and half were randomized to meet participants met for weekly, peer-led sessions delivered from a scripted team-based health and safety curriculum. Curriculum addressed: exercise, nutrition, stress, sleep, body weight, injury, and other unhealthy lifestyle behaviours such as smoking and heavy alcohol use. Health and safety questionnaires administered before and after the intervention found significant improvements for increased fruit and vegetable consumption, overall healthy eating, increased sleep quantity and sleep quality, and reduced personal stress.

Process of quantity determination of uranium by chromatography in liquid zone

International Nuclear Information System (INIS)

Muller, J.P.; Cojean, J.; Daubizit, M.

1993-01-01

The invention concerns a process of quantity determination of uranium by chromatography in liquid zone, usable to determine the quantity of uranium traces. Solutions to be treated can be aqueous or organic

Ultraviolet safety assessments of insect light traps.

Science.gov (United States)

Sliney, David H; Gilbert, David W; Lyon, Terry

2016-01-01

Near-ultraviolet (UV-A: 315-400 nm), "black-light," electric lamps were invented in 1935 and ultraviolet insect light traps (ILTs) were introduced for use in agriculture around that time. Today ILTs are used indoors in several industries and in food-service as well as in outdoor settings. With recent interest in photobiological lamp safety, safety standards are being developed to test for potentially hazardous ultraviolet emissions. A variety of UV "Black-light" ILTs were measured at a range of distances to assess potential exposures. Realistic time-weighted human exposures are shown to be well below current guidelines for human exposure to ultraviolet radiation. These UV-A exposures would be far less than the typical UV-A exposure in the outdoor environment. Proposals are made for realistic ultraviolet safety standards for ILT products.

Impact of the Velo 2 half misalignment on physical quantities

CERN Document Server

Roguljic, Matej; Borghi, Silvia; Grillo, Lucia; CERN. Geneva. EP Department

2016-01-01

The impact of the misalignment of the Vertex Locator of the LHCb experiment on the physical quantities of the decay "$D^{*+} \\rightarrow (D^{0}\\rightarrow K^{-}\\pi^{+}) \\pi^{+} $" is studied in this note. Different misalignments of the 2 halves are applied to Monte Carlo data and the variations of the physical quantities with respect to the case without misalignment are evaluated. The results show the importance of the VELO 2 half alignment which can significantly affect the physics performance in the large misalignment case. A misalignment equal to the precision of the real-time alignment of the Vertex Locator is found to have a negligible effect on the studied physical quantities.

Nuclear safety and radiation protection report of Blayais nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 86 and 110). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Civaux nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 158 and 159). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Golfech nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 135 and 142). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Tricastin nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the Tricastin NPPs (INBs no. 87 and 88). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Penly nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 136 and 140). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Cattenom nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 124, 125, 126 and 137). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Chooz nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 139, 144 and 163 (under dismantling)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Flamanville nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 108, 109 and 167 (under construction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Fessenheim nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INB no. 75). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Pedestrian Safety in Road Traffic in Poland

Science.gov (United States)

Budzynski, Marcin; Jamroz, Kazimierz; Mackun, Tomasz

2017-10-01

Every third road accident in Poland involves a pedestrian as a participant or, most of the time, a casualty. Pedestrian accidents are usually the result of complex situations and the outcome of a number of factors related to driver and pedestrian behaviour and road infrastructure. Safety depends largely on how well the traffic condition is perceived and on visibility in traffic. The paper presents the results of analyses of methodologies for systematic studies of pedestrian behaviour and pedestrian-driver relations. The effects of the location of the site, type of cross-section and other selected parameters on pedestrian and driver behaviour are demonstrated. The analyses showed that pedestrians are most often put at risk by too long pedestrian crossings, vehicles going too fast around pedestrian crossings, lack of proper sight distance and poorly lit or unlit pedestrian crossings. The reason for such defective infrastructure is that planners, designers, contractors and maintenance services are not receiving any support from design, marking and maintenance regulations for pedestrian traffic. In addition, the Road Traffic Law is not restrictive enough when it comes to drivers’ obligations towards pedestrian safety. Polish design regulations allow long pedestrian crossings up to four lanes in one direction or three lanes in two directions irrespective of traffic control and speed limits. Pedestrian crossings should be kept at a maximum of three lanes. There is nothing in the design regulations about the required driver-pedestrian sight distance. Neither does the Road Traffic Law help engineers with that. It is legal to park vehicles within 10 m of a pedestrian crossing which does not guarantee the necessary sight distance. Drivers must be able to see a pedestrian waiting or stepping onto the crossing from a distance that will help them come to a stop safely. It is safer to follow the principle of providing adequate pedestrian sight distance. Recommendations for

Association between work-family conflict and smoking quantity among daily smokers.

Science.gov (United States)

Macy, Jonathan T; Chassin, Laurie; Presson, Clark C

2013-11-01

Recent work demonstrated a direct relation between work-family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work-family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors.

Quantities of natural gas transported in January-December 2009

International Nuclear Information System (INIS)

2010-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the monthly key figures of GRTgaz activity in 2009: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Determining cutoff distances for assessing risks from transportation accident radiation releases

International Nuclear Information System (INIS)

Sandquist, G.M.; Slaughter, D.M.; Kimura, C.Y.; Brumburgh, G.

1995-01-01

The transportation of radioactive materials throughout the United States and the world is a ubiquitous and sometimes controversial activity. Almost universally, these transportation activities have been performed without major incident, and the safety record for transportation of radioactive material is outstanding compared with the transportation of other hazardous materials. Nevertheless, concerns still exist regarding adequate regulation of radioactive material transportation and accurate assessment of the health risks associated with accidents. These concerns are addressed through certification by the cognizant regulatory authority over the transportation container or the performance of a transportation risk assessment. In a transportation risk assessment, accident situations are examined, frequencies are estimated, and consequences resulting from the accident are analyzed and evaluated for acceptance. A universal question with any transportation risk assessment that examines the radiological consequences from release accidents is, At what distance may the dispersion analysis be terminated? This paper examines cutoff distances and their consequences for assessing health risks from radiological transportation releases

48 CFR 852.270-2 - Bread and bakery products-quantities.

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Bread and bakery products... Bread and bakery products—quantities. As prescribed in 870.111-3, insert the following clause: Bread and Bakery Products—Quantities (JAN 2008) The bidder agrees to furnish up to 25 percent more or 25 percent...

Safeguards Implementation Guide for States with Small Quantities Protocols

International Nuclear Information System (INIS)

2013-01-01

The International Atomic Energy Agency (IAEA) works to enhance the contribution of nuclear energy for peace and prosperity around the world, while helping to ensure that nuclear material is not diverted to nuclear weapons or other nuclear explosive devices. In implementing safeguards, the IAEA plays an instrumental independent verification role, providing credible assurances that States' safeguards commitments are being respected. Most of the world's non-nuclear-weapon States (NNWSs) have concluded comprehensive safeguards agreements (CSAs) with the IAEA, pursuant to the Treaty on the Non- Proliferation of Nuclear Weapons (NPT). The IAEA and States are required to cooperate in the implementation of such agreements. Effective cooperation demonstrates a State's commitment to the peaceful use of nuclear energy and furthers the State's national interests by reducing the risk of unauthorized use of nuclear material. Over 100 NNWSs party to the NPT have very limited quantities of nuclear material and have concluded protocols to their CSAs which hold in abeyance many procedures in Part II of a CSA. These protocols are referred to as 'small quantities protocols' or 'SQPs' and remain in effect as long as the State meets certain eligibility criteria. The purpose of an SQP is to reduce the burden of safeguards implementation for States with little or no nuclear activities, while retaining the integrity of the safeguards system. States with SQPs have very important obligations they must fulfil under their CSAs. In 1997, as part of the IAEA's efforts to strengthen its safeguards system, the Model Additional Protocol to the Agreement(s) between State(s) and the International Atomic Energy Agency for the Application of Safeguards was developed to provide the IAEA with broader access to information and locations, thus significantly increasing the IAEA's ability to provide assurance of the absence of undeclared nuclear material and activities in States. Many States with SQPs have

THE DISTANCE TO M51

Energy Technology Data Exchange (ETDEWEB)

McQuinn, Kristen B. W. [University of Texas at Austin, McDonald Observatory, 2515 Speedway, Stop C1400 Austin, TX 78712 (United States); Skillman, Evan D. [Minnesota Institute for Astrophysics, School of Physics and Astronomy, 116 Church Street, S.E., University of Minnesota, Minneapolis, MN 55455 (United States); Dolphin, Andrew E. [Raytheon Company, 1151 E. Hermans Road, Tucson, AZ 85756 (United States); Berg, Danielle [Center for Gravitation, Cosmology and Astrophysics, Department of Physics, University of Wisconsin Milwaukee, 1900 East Kenwood Boulevard, Milwaukee, WI 53211 (United States); Kennicutt, Robert, E-mail: kmcquinn@astro.as.utexas.edu [Institute for Astronomy, University of Cambridge, Madingley Road, Cambridge CB3 0HA (United Kingdom)

2016-07-20

Great investments of observing time have been dedicated to the study of nearby spiral galaxies with diverse goals ranging from understanding the star formation process to characterizing their dark matter distributions. Accurate distances are fundamental to interpreting observations of these galaxies, yet many of the best studied nearby galaxies have distances based on methods with relatively large uncertainties. We have started a program to derive accurate distances to these galaxies. Here we measure the distance to M51—the Whirlpool galaxy—from newly obtained Hubble Space Telescope optical imaging using the tip of the red giant branch method. We measure the distance modulus to be 8.58 ± 0.10 Mpc (statistical), corresponding to a distance modulus of 29.67 ± 0.02 mag. Our distance is an improvement over previous results as we use a well-calibrated, stable distance indicator, precision photometry in a optimally selected field of view, and a Bayesian Maximum Likelihood technique that reduces measurement uncertainties.

Encyclopedia of distances

CERN Document Server

Deza, Michel Marie

2009-01-01

Distance metrics and distances have become an essential tool in many areas of pure and applied Mathematics. This title offers both independent introductions and definitions, while at the same time making cross-referencing easy through hyperlink-like boldfaced references to original definitions.

Selection of detailed items for periodic safety review on PWR radwaste management system

Energy Technology Data Exchange (ETDEWEB)

Sung, K. B.; Ahn, Y. S.; Park, Y. S.; Kim, S. H.; Kim, J. T. [Korea Hydric and Nuclear Power Company, Taejon (Korea, Republic of)

2003-10-01

Selection of detailed-items for Periodic Safety Review on PWR radwaste management system, the main component could be faithfully clarified according to the purpose of establishment on each system and basic purpose. It is proper to select detailed-items those of radioactivities in the reactor coolant activity levels and the released volume of liquid and gaseous radioactive material on safety performance. It's also proper to select solid radwaste production quantities as detailed-item that it would be predict the next ten years trends after PSR.

How tobacco companies have used package quantity for consumer targeting.

Science.gov (United States)

Persoskie, Alexander; Donaldson, Elisabeth A; Ryant, Chase

2018-05-31

Package quantity refers to the number of cigarettes or amount of other tobacco product in a package. Many countries restrict minimum cigarette package quantities to avoid low-cost packs that may lower barriers to youth smoking. We reviewed Truth Tobacco Industry Documents to understand tobacco companies' rationales for introducing new package quantities, including companies' expectations and research regarding how package quantity may influence consumer behaviour. A snowball sampling method (phase 1), a static search string (phase 2) and a follow-up snowball search (phase 3) identified 216 documents, mostly from the 1980s and 1990s, concerning cigarettes (200), roll-your-own tobacco (9), smokeless tobacco (6) and 'smokeless cigarettes' (1). Companies introduced small and large packages to motivate brand-switching and continued use among current users when faced with low market share or threats such as tax-induced price increases or competitors' use of price promotions. Companies developed and evaluated package quantities for specific brands and consumer segments. Large packages offered value-for-money and matched long-term, heavy users' consumption rates. Small packages were cheaper, matched consumption rates of newer and lighter users, and increased products' novelty, ease of carrying and perceived freshness. Some users also preferred small packages as a way to try to limit consumption or quit. Industry documents speculated about many potential effects of package quantity on appeal and use, depending on brand and consumer segment. The search was non-exhaustive, and we could not assess the quality of much of the research or other information on which the documents relied. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

A shared system of representation governing quantity discrimination in canids

Directory of Open Access Journals (Sweden)

Joseph M Baker

2012-10-01

Full Text Available One way to investigate the evolution of cognition is to compare the abilities of phylogenetically related species. The domestic dog (Canis lupus familiaris, for example, still shares cognitive abilities with the coyote (C. latrans. Both of these canids possess the ability to make psychophysical less/more discriminations of food based on quantity. Like many other species including humans, this ability is mediated by Weber’s Law: discrimination of continuous quantities is dependent on the ratio between the two quantities. As two simultaneously presented quantities of food become more similar, choice of the large or small option becomes random in both dogs and coyotes. It remains unknown, however, whether these closely related species within the same family—one domesticated, and one wild—make such quantitative comparisons with comparable accuracy. Has domestication honed or diminished this quantitative ability? Might different selective and ecological pressures facing coyotes drive them to be more or less able to accurately represent and discriminate food quantity than domesticated dogs? This study is an effort to elucidate this question concerning the evolution of non-verbal quantitative cognition.Here, we tested the quantitative discrimination ability of 16 domesticated dogs. Each animal was given 9 trials in which two different quantities of food were simultaneously displayed to them. The domesticated dogs’ performance on this task was then compared directly to the data from 16 coyotes’ performance on this same task reported by Baker and colleagues (2011.The quantitative discrimination abilities between the two species were strikingly similar. Domesticated dogs demonstrated similar quantitative sensitivity as coyotes, suggesting that domestication may not have significantly altered the psychophysical discrimination abilities of canids. Instead, this study provides further evidence for similar nonverbal quantitative abilities across

Variation in Quantity of Heat Produced from Charcoal of Prosopis ...

African Journals Online (AJOL)

Data were collected using the copper calorimeter, a thermometer, an air tight burner and a weight balance. The results showed a gradual decrease in the quantity of heat produced as combustion time increased from 10 40 minutes in all wood species. Significant differences (p<0.05) in the quantity of heat produced both ...

Multimodal semantic quantity representations: further evidence from Korean Sign Language

Directory of Open Access Journals (Sweden)

Frank eDomahs

2012-01-01

Full Text Available Korean deaf signers performed a number comparison task on pairs of Arabic digits. In their RT profiles, the expected magnitude effect was systematically modified by properties of number signs in Korean Sign Language in a culture-specific way (not observed in hearing and deaf Germans or hearing Chinese. We conclude that finger-based quantity representations are automatically activated even in simple tasks with symbolic input although this may be irrelevant and even detrimental for task performance. These finger-based numerical representations are accessed in addition to another, more basic quantity system which is evidenced by the magnitude effect. In sum, these results are inconsistent with models assuming only one single amodal representation of numerical quantity.

Foraging behavior of bee pollinators on the tropical weed Triumfetta semitriloba: flight distance and directionality.

Science.gov (United States)

Collevatti, R G; Schoereder, J H; Campos, L A

2000-02-01

We studied flight distance and directionality of bee pollinators on the tropical shrub weed Triumfetta semitriloba Jacq. (Tiliaceae), addressing (1) within- and between-plant movement pattern; (2) distances flown between plants; (3) flight directionality. Flowering plants were distributed in well-delimited clumps, in each of two pasture areas (A1 and A2) and one area of forest gap (A3), in Viçosa, southeastern Brazil. Five solitary bee species, Augochlorella michaelis, Augochloropsis cupreola, Pseudocentron paulistana, Ceratinula sp., Melissodes sexcincta, and two social bee, Plebeia droryana, P. cf. nigriceps were observed. All species moved mainly to the nearest flower on the same individual plant and, in between-plant movements, to the first or second nearest neighbor. All species moved non-randomly, presenting a flight directionality in departures (maintenance of flight direction), but with a high frequency of turn angles. It is suggested that this foraging behavior pattern occurred because of the resource quantity and quality (pollen or nectar), and environmental characteristics such as flower density and resource distribution.

The effects of quantity and depth of processing on children's time perception.

Science.gov (United States)

Arlin, M

1986-08-01

Two experiments were conducted to investigate the effects of quantity and depth of processing on children's time perception. These experiments tested the appropriateness of two adult time-perception models (attentional and storage size) for younger ages. Children were given stimulus sets of equal time which varied by level of processing (deep/shallow) and quantity (list length). In the first experiment, 28 children in Grade 6 reproduced presentation times of various quantities of pictures under deep (living/nonliving categorization) or shallow (repeating label) conditions. Students also compared pairs of durations. In the second experiment, 128 children in Grades K, 2, 4, and 6 reproduced presentation times under similar conditions with three or six pictures and with deep or shallow processing requirements. Deep processing led to decreased estimation of time. Higher quantity led to increased estimation of time. Comparative judgments were influenced by quantity. The interaction between age and depth of processing was significant. Older children were more affected by depth differences than were younger children. Results were interpreted as supporting different aspects of each adult model as explanations of children's time perception. The processing effect supported the attentional model and the quantity effect supported the storage size model.

Testing quantity theory of money for the Turkish economy

OpenAIRE

Levent, Korap

2007-01-01

In this paper, it is tried to test the main assumptions of the Quantity Theory of Money for the Turkish economy. Using some contemporaneous estimation techniques to examine the long-run stationary economic relationships on which the quantity theory is constructed, it is found that stationary characteristics of the velocitities of narrowly and broadly defined monetary aggregates cannot be rejected. However, monetary aggregates seem to be endogenous for the long-run evoluation of prices and rea...

Association Between Work–Family Conflict and Smoking Quantity Among Daily Smokers

Science.gov (United States)

2013-01-01

Introduction: Recent work demonstrated a direct relation between work–family conflict and likelihood of smoking. This study furthered this area of research by (a) testing the association between work–family conflict and smoking quantity and (b) testing demographic, workplace, and home factors as moderators of this relation. Methods: Participants (N = 423) were daily smokers from a Midwestern community-based sample. Ordinal regression analysis tested work-to-home and home-to-work conflict as predictors (after controlling for demographic characteristics, home factors, and workplace factors) of smoking quantity. Additionally, we tested whether the demographic, home, and workplace factors moderated the effects of work-to-home conflict and home-to-work conflict on smoking quantity. Results: Males (OR = 8.81, p = .005), older participants (OR = 1.09, p = .012), those with less educational attainment (OR = 1.87, p = .001), those who reported lower levels of workplace smoking restrictions (OR = 0.87, p = .019), and those who reported higher levels of work-to-home conflict (OR = 1.39, p = .026) smoked more cigarettes per day. There was no significant main effect of home-to-work conflict on smoking quantity (OR = 1.46, p = .099). A significant interaction (OR = 0.55, p = .043) revealed that home-to-work conflict was associated with smoking quantity for females but not for males. Conclusions: After controlling for demographic characteristics and potential confounders, work-to-home conflict had a negative impact on smoking quantity for all participants, and home-to-work conflict was associated with smoking quantity for women. Workplace wellness programs to reduce smoking among employees should take into account the direction of conflict and how the effect of the conflict on smoking behavior may vary based on other factors. PMID:23709611

Quantities of natural gas transported in August-December 2007

International Nuclear Information System (INIS)

2008-01-01

GRTgaz is a European leader in natural gas transmission, a world expert in gas transmission networks and systems, and an operator firmly committed to the energy transition. It owns and operates the gas transmission network throughout most of France and it manages the transmission network in Germany, thereby helping to ensure correct operation of the French and European gas market. It contributes to the energy security of regional supply systems and performs a public service mission to ensure the continuity of consumer supply. This document presents the available monthly key figures of GRTgaz activity from August to December 2007: Total quantities transmitted by GRTgaz (Inputs to the GRTgaz network/Outputs from the GRTgaz network); Maximum and minimum daily flow (Daily quantities transported, Daily consumption, Daily inputs excluding storage); Quantities exchanged on the wholesale market; Consumption on the GRTgaz Network (gross monthly consumption and Average monthly temperatures)

Symbols and definitions of quantities and units in isotope stoichiometry

International Nuclear Information System (INIS)

Junghans, P.; Krumbiegel, P.; Faust, H.

1982-01-01

On the basis of the International System of Units and recent recommendations of the IUPAC on 'Symbols and Terminology for Physicochemical Quantities and Units' a system is proposed of uniform and unambiguous symbols and definitions of quantities and units used in the isotope dilution technique. The close relationship between isotope stoichiometry and common stoichiometry is demonstrated. (author)

Measurement of kVp, PPV and air kerma values in function of the electric current quantity and the focus-detector distance in one X-ray equipment

International Nuclear Information System (INIS)

Lucena, Rodrigo F. de; Potiens, Maria da Penha A.; Vivolo, Vitor

2009-01-01

The objective of this work was to study the behavior of the X-ray equipment Pantak/Seifert, model MXR-160/22 of the calibration laboratory of IPEN, LCI, operating in the diagnostic radiology radiation quality RQR 5 (70 kV). For this evaluation it was used a noninvasive meter PTW, Diavolt TM model. The measurements of kVp, PPV and Dose (air kerma), were made varying the electric current and distance between the focal point and the meter. This behavior is described in the literature and was expected in the analysis of the measurements for comparison purposes. For the tests where it was only increased the electric current it was waited a linear increase of the dose (air kerma), but not a variation in the kVp and PPV. The measurements had corresponded to the waited behavior, since the Dose (air kerma) measurements presented a linear increase with the increase of the electric current and the kVp and PPV values showed a variation less than 2%. In the corresponding measurements increasing the distance between focal point and meter, it was waited the exponentially decreasing of the Dose (air kerma) and again a small variation or no variation of the PPV and kVP with the increase of the distance. Over again the measurements corresponded to the expected, where the Dose (air kerma) decreased exponentially and the PPV and the kVp had a variation less than 1.5%. (author)

Estimation of distance error by fuzzy set theory required for strength determination of HDR (192)Ir brachytherapy sources.

Science.gov (United States)

Kumar, Sudhir; Datta, D; Sharma, S D; Chourasiya, G; Babu, D A R; Sharma, D N

2014-04-01

Verification of the strength of high dose rate (HDR) (192)Ir brachytherapy sources on receipt from the vendor is an important component of institutional quality assurance program. Either reference air-kerma rate (RAKR) or air-kerma strength (AKS) is the recommended quantity to specify the strength of gamma-emitting brachytherapy sources. The use of Farmer-type cylindrical ionization chamber of sensitive volume 0.6 cm(3) is one of the recommended methods for measuring RAKR of HDR (192)Ir brachytherapy sources. While using the cylindrical chamber method, it is required to determine the positioning error of the ionization chamber with respect to the source which is called the distance error. An attempt has been made to apply the fuzzy set theory to estimate the subjective uncertainty associated with the distance error. A simplified approach of applying this fuzzy set theory has been proposed in the quantification of uncertainty associated with the distance error. In order to express the uncertainty in the framework of fuzzy sets, the uncertainty index was estimated and was found to be within 2.5%, which further indicates that the possibility of error in measuring such distance may be of this order. It is observed that the relative distance li estimated by analytical method and fuzzy set theoretic approach are consistent with each other. The crisp values of li estimated using analytical method lie within the bounds computed using fuzzy set theory. This indicates that li values estimated using analytical methods are within 2.5% uncertainty. This value of uncertainty in distance measurement should be incorporated in the uncertainty budget, while estimating the expanded uncertainty in HDR (192)Ir source strength measurement.

Varieties of Quantity Estimation in Children

Science.gov (United States)

Sella, Francesco; Berteletti, Ilaria; Lucangeli, Daniela; Zorzi, Marco

2015-01-01

In the number-to-position task, with increasing age and numerical expertise, children's pattern of estimates shifts from a biased (nonlinear) to a formal (linear) mapping. This widely replicated finding concerns symbolic numbers, whereas less is known about other types of quantity estimation. In Experiment 1, Preschool, Grade 1, and Grade 3…

40 CFR 273.8 - Applicability-household and conditionally exempt small quantity generator waste.

Science.gov (United States)

2010-07-01

... conditionally exempt small quantity generator waste. 273.8 Section 273.8 Protection of Environment ENVIRONMENTAL....8 Applicability—household and conditionally exempt small quantity generator waste. (a) Persons... universal wastes defined at § 273.9; and/or (2) Conditionally exempt small quantity generator wastes that...

Learner characteristics involved in distance learning

Energy Technology Data Exchange (ETDEWEB)

Cernicek, A.T.; Hahn, H.A.

1991-01-01

Distance learning represents a strategy for leveraging resources to solve educational and training needs. Although many distance learning programs have been developed, lessons learned regarding differences between distance learning and traditional education with respect to learner characteristics have not been well documented. Therefore, we conducted a survey of 20 distance learning professionals. The questionnaire was distributed to experts attending the second Distance Learning Conference sponsored by Los Alamos National Laboratory. This survey not only acquired demographic information from each of the respondents but also identified important distance learning student characteristics. Significant distance learner characteristics, which were revealed statistically and which influence the effectiveness of distance learning, include the following: reading level, student autonomy, and self-motivation. Distance learning cannot become a more useful and effective method of instruction without identifying and recognizing learner characteristics. It will be important to consider these characteristics when designing all distance learning courses. This paper will report specific survey findings and their implications for developing distance learning courses. 9 refs., 6 tabs.

Safety system in a heavy water detritiation plant

International Nuclear Information System (INIS)

Balteanu, O.; Stefan, I.; Retevoi, C.

2003-01-01

In a CANDU 6 type reactor a quantity of 55·10 15 Bq/year of tritium is generated, 95% being in the D 2 O moderator which can achieve a radioactivity of 2.5-3.5·10 12 Bq/kg. Tritium in heavy water contributes with 30-50% to the doses received by operation personnel and up to 20% to the radioactivity released in the environment. The large quantity of heavy water used in this type of reactors (500 tones) make storage very difficult, especially for environment. The extraction of tritium from tritiated heavy water of CANDU reactors solve the following problems: the radiation level in the operation area, the costs of maintenance and repair reduction due to reduction of personnel protection measures, the increase of NPP utilisation factor by shutdown time reduction for maintenance and repair, use the extracted tritium for fusion reactors and not for the last, lower costs and risk for storage heavy water waste. Heavy water detritiation methods, which currently are used in the industrial or experimental plant, are based on catalytic isotope exchange or electrolysis followed cryogenic distillation or permeation. The technology developed at Institute of Cryogenics and Isotope Separation is based upon catalytic exchange between tritiated water and deuterium, followed by cryogenic distillation of hydrogen isotopes. The nature of the fluids that are processed in detritiation requires the operation of the plant in safety conditions. The paper presents the safety system solution chose in order to solve this task, as well as a simulation of an incident and safety system response. The application software is using LabView platform that is specialised on control and factory automation applications. (author)

Nuclear safety and radiation protection report of the nuclear facility of Brennilis - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the partially dismantled facilities of the Monts d'Arree (EL4-D or Brennilis) site (INB 162 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the nuclear facilities of Brennilis - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the partially dismantled facilities of the Monts d'Arree (EL4-D or Brennilis) site (INB 162 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Distance Magic-Type and Distance Antimagic-Type Labelings of Graphs

Science.gov (United States)

Freyberg, Bryan J.

Generally speaking, a distance magic-type labeling of a graph G of order n is a bijection l from the vertex set of the graph to the first n natural numbers or to the elements of a group of order n, with the property that the weight of each vertex is the same. The weight of a vertex x is defined as the sum (or appropriate group operation) of all the labels of vertices adjacent to x. If instead we require that all weights differ, then we refer to the labeling as a distance antimagic-type labeling. This idea can be generalized for directed graphs; the weight will take into consideration the direction of the arcs. In this manuscript, we provide new results for d-handicap labeling, a distance antimagic-type labeling, and introduce a new distance magic-type labeling called orientable Gamma-distance magic labeling. A d-handicap distance antimagic labeling (or just d-handicap labeling for short) of a graph G = ( V,E) of order n is a bijection l from V to the set {1,2,...,n} with induced weight function [special characters omitted]. such that l(xi) = i and the sequence of weights w(x 1),w(x2),...,w (xn) forms an arithmetic sequence with constant difference d at least 1. If a graph G admits a d-handicap labeling, we say G is a d-handicap graph. A d-handicap incomplete tournament, H(n,k,d ) is an incomplete tournament of n teams ranked with the first n natural numbers such that each team plays exactly k games and the strength of schedule of the ith ranked team is d more than the i + 1st ranked team. That is, strength of schedule increases arithmetically with strength of team. Constructing an H(n,k,d) is equivalent to finding a d-handicap labeling of a k-regular graph of order n.. In Chapter 2 we provide general constructions for every d for large classes of both n and k, providing breadfth and depth to the catalog of known H(n,k,d)'s. In Chapters 3 - 6, we introduce a new type of labeling called orientable Gamma-distance magic labeling. Let Gamma be an abelian group of order

Computer-aided safety systems of industrial high energy objects

International Nuclear Information System (INIS)

Topolsky, N.G.; Gordeev, S.G.

1995-01-01

Modern objects of fuel and energy, chemical industries are characterized by high power consumption; by presence of large quantities of combustible and explosive substances used in technological processes; by advanced communications of submission systems of initial liquid and gasiform reagents, lubricants and coolants, the products of processing, and wastes of production; by advanced ventilation and pneumatic transport; and by complex control systems of energy, material and information flows. Such objects have advanced infrastructures, including a significant quantity of engineering buildings intended for storage, transportation, and processing of combustible liquids, gasiform fuels and materials, and firm materials. Examples of similar objects are nuclear and thermal power stations, chemical plants, machine-building factories, iron and steel industry enterprises, etc. Many tasks and functions characterizing the problem of fire safety of these objects can be accomplished only upon the development of special Computer-Aided Fire Safety Systems (CAFSS). The CAFSS for these objects are intended to reduce the hazard of disastrous accidents both causing fires and caused by them. The tasks of fire prevention and rescue work of large-scale industrial objects are analyzed within the bounds of the recommended conception. A functional structure of CAFSS with a list of the main subsystems forming a part of its composition has been proposed

Distance-transitive graphs

NARCIS (Netherlands)

Cohen, A.M.; Beineke, L.W.; Wilson, R.J.; Cameron, P.J.

2004-01-01

In this chapter we investigate the classification of distance-transitive graphs: these are graphs whose automorphism groups are transitive on each of the sets of pairs of vertices at distance i, for i = 0, 1,.... We provide an introduction into the field. By use of the classification of finite

Memory for multiple cache locations and prey quantities in a food-hoarding songbird

Directory of Open Access Journals (Sweden)

Nicola eArmstrong

2012-12-01

Full Text Available Most animals can discriminate between pairs of numbers that are each less than four without training. However, North Island robins (Petroica longipes, a food hoarding songbird endemic to New Zealand, can discriminate between quantities of items as high as eight without training. Here we investigate whether robins are capable of other complex quantity discrimination tasks. We test whether their ability to discriminate between small quantities declines with 1. the number of cache sites containing prey rewards and 2. the length of time separating cache creation and retrieval (retention interval. Results showed that subjects generally performed above chance expectations. They were equally able to discriminate between different combinations of prey quantities that were hidden from view in 2, 3 and 4 cache sites from between 1, 10 and 60 seconds. Overall results indicate that North Island robins can process complex quantity information involving more than two discrete quantities of items for up to one minute long retention intervals without training.

Charaterisation of function spaces via mollification; fractal quantities for distributions

Directory of Open Access Journals (Sweden)

Hans Triebel

2003-01-01

Full Text Available The aim of this paper is twofold. First we characterise elements f belonging to the Besov spaces Bpqs(ℝn with s∈ℝ,  0quantities for distributions generalising well-known corresponding quantities for Radon measures.

Nuclear safety and radiation protection report of the Paluel nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 103, 104, 114 and 115). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Penly nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 136 and 140). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Paluel nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 103, 104, 114 and 115). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Civaux nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 158 and 159). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of Cruas-Meysse nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 111 and 112). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of the Penly nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 136 and 140). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Fessenheim nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INB no. 75). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Golfech nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 135 and 142). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Civaux nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 158 and 159). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Flamanville nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 108, 109 and 167 (under construction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Chooz nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 139, 144 and 163 (under dismantling)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Cattenom nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 124, 125, 126 and 137). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Chooz nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 139, 144 and 163 (under dismantling)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Blayais nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 86 and 110). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Cattenom nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 124, 125, 126 and 137). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Flamanville nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 108, 109 and 167 (under construction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Prices versus Quantities

DEFF Research Database (Denmark)

Hansen, Lars Gårn; Jensen, Frank

illustrate that this result does not generalise to a search fishery, where marginal costs are allowed to depend on harvest. Hansen et al (2008) study a fishery where non-compliance with regulations is a problem. When the regulator is uncertain about non-compliance (compliance uncertainty), then landing fees......Weitzman (2002) studies the regulation of a fishery characterised by constant marginal harvest costs and shows that price regulation performs better than quantity regulation when the regulator is uncertain about the biological reproduction function (ecological uncertainty). Here, we initially...... are the preferred type of regulation, and Hansen et al (2008) find that this result does generalise to a search fishery where marginal costs depend on harvest. In this paper, we simulate a stochastic stock-recruitment model for the Danish cod fishery in the Kategat capturing both ecological and compliance...

Allen's astrophysical quantities

CERN Document Server

2000-01-01

This new, fourth, edition of Allen's classic Astrophysical Quantities belongs on every astronomer's bookshelf. It has been thoroughly revised and brought up to date by a team of more than ninety internationally renowned astronomers and astrophysicists. While it follows the basic format of the original, this indispensable reference has grown to more than twice the size of the earlier editions to accommodate the great strides made in astronomy and astrophysics. It includes detailed tables of the most recent data on: - General constants and units - Atoms, molecules, and spectra - Observational astronomy at all wavelengths from radio to gamma-rays, and neutrinos - Planetary astronomy: Earth, planets and satellites, and solar system small bodies - The Sun, normal stars, and stars with special characteristics - Stellar populations - Cataclysmic and symbiotic variables, supernovae - Theoretical stellar evolution - Circumstellar and interstellar material - Star clusters, galaxies, quasars, and active galactic nuclei ...

Generalized railway tank car safety design optimization for hazardous materials transport: Addressing the trade-off between transportation efficiency and safety

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Barkan, Christopher P.L.

2011-01-01

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials.

Variations of influence quantities in industrial irradiators and their effect on dosimetry performance

International Nuclear Information System (INIS)

Chu, R.D.H.

1999-01-01

Many environmental factors, including irradiation temperature, post-irradiation storage temperature, dose rate, relative humidity, oxygen content and the energy spectrum may affect the response of dosimetry systems used in industrial radiation processing. Although the effects of individual influence quantities have been extensively studied, the variations of these influence quantities in production irradiators and the complex relationships between the effects of different influence quantities make it difficult to assess the overall effect on the measurement uncertainty. In the development of new dosimetry systems it is important to know the effect of each influence quantity and developers of new dosimetry systems should perform studies over a wide range of irradiation conditions. Analysis parameters and manufacturing specifications should be chosen to minimize the effect of influence quantities in the environments where the dosimeters will be used. Because of possible relationships between different influence quantities, care must be taken to ensure that the response function determined in the calibration of the dosimetry system is applicable for the conditions in which the dosimeters will be used. Reference standard dosimetry systems which have been thoroughly studied and have known relationships between dose response and influence quantities should be used to verify the calibration of routine dosimetry systems under the actual conditions of use. Better understanding of the variations in influence quantities in industrial irradiators may be obtained by modeling or direct measurements and may provide improvements in the calibration of routine dosimetry system and reduction of the overall measurement uncertainty. (author)

Boundary conditions for pathways, safety analysis and basic criteria for low-level radiation waste site selection

International Nuclear Information System (INIS)

Saverot, P.

1994-01-01

There are three successive periods in the life of a disposal facility: the operating period, the institutional control period and the unrestricted site access period. The purpose of safety analysis of the disposal facility is to ensure that the radiological impacts for each period in the life of the facility are acceptable under all circumstances. Founded on a deterministic approach, this analysis leads to a determination of the maximum quantity of each radionuclide present in the facility at the beginning of the institutional control period in order for the impacts to be considered acceptable. Safety analysis involves the calculation of the radiological impacts of a given radiological inventory under a selected scenario, from all plausible scenarios of radionuclide migration to the environment in both normal and accident conditions, and taking into account other specified variables. The calculation itself involves an assessment of the quantities of radionuclides that could be released to the environment under the specific scenario selected and following identified pathways, and a determination of the resultant exposure, both internal and external, to the public. An iterative approach is used in the performance of pathways analyses. If the pathways analyses result in unacceptable radiological impacts, either the radiological inventory of the site is reduced or barrier characteristics not previously factored into the analysis are taken into account. New pathways analyses are then performed until the results are within the acceptable range. Once accepted by the safety authorities, the radiological inventory becomes the radiological capacity, which is the approved quantities of specific radionuclides that may be disposed of at the site. The following elaborates on the boundary conditions used in safety analyses and describes the types of pathways analyses performed for a LLW disposal facility

Patterns in new dimensionless quantities containing melting temperature, and their dependence on pressure

Directory of Open Access Journals (Sweden)

U. WALZER

1980-06-01

Full Text Available The relationships existing between melting temperature and other
macroscopic physical quantities are investigated. A new dimensionless
quantity Q(1 not containing the Grtineisen parameter proves to be suited for serving in future studies as a tool for the determination of the melting temperature in the outer core of the Earth. The pressure dependence of more general dimensionless quantities Q„ is determined analytically and, for the chemical elements, numerically, too. The patterns of various interesting dimensionless quantities are shown in the Periodic Table and compared.

First Year Chemistry Laboratory Courses for Distance Learners: Development and Transfer Credit Acceptance

Directory of Open Access Journals (Sweden)

Sharon E. Brewer,

2013-07-01

Full Text Available In delivering chemistry courses by distance, a key challenge is to offer the learner an authentic and meaningful laboratory experience that still provides the rigour required to continue on in science. To satisfy this need, two distance general chemistry laboratory courses appropriate for Bachelor of Science (B.Sc. students, including chemistry majors, have been recently developed at Thompson Rivers University. A constructive alignment process was employed which clearly mapped learning outcomes and activities to appropriate assessment tools. These blended laboratory courses feature custom, home experimental kits and combine elements of online and hands-on learning. The courses were designed for flexible continuous enrollment and provide online resources including tutor support, instructional videos, lab report submission, and student evaluation. The assessment of students includes laboratory reports, safety quizzes, reflective journaling, digital photo documentation, and invigilated written and online practical exams. Emphasizing the quality and rigour in these distance laboratory learning experiences allowed both courses to be accepted for B.Sc. transfer credit by other institutions, an important criterion for students. This paper will outline the design and development process of these new blended laboratory courses, their course structures and assessments, and initial student results.

Fuel and canister process report for the safety assessment SR-Can

International Nuclear Information System (INIS)

Werme, Lars

2006-10-01

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The report is written by, and for, experts in the relevant scientific fields. It should though be possible for a generalist in the area of long-term safety assessments of geologic nuclear waste repositories to comprehend the contents of the report. The report is an important part of the documentation of the SR-Can project and an essential reference within the project, providing a scientifically motivated plan for the handling of geosphere processes. It is, furthermore, foreseen that the report will be essential for reviewers scrutinising the handling of geosphere issues in the SR-Can assessment. Several types of fuel will be emplaced in the repository. For the reference case with 40 years of reactor operation, the fuel quantity from boiling water reactors, BWR fuel, is estimated at 7,000 tonnes, while the quantity from pressurized water reactors, PWR fuel, is estimated at about 2,300 tonnes. In addition, 23 tonnes of mixed-oxide fuel (MOX) fuel of German origin from BWR and PWR reactors and 20 tonnes of fuel from the decommissioned heavy water reactor in Aagesta will be disposed of. To allow for future changes in the Swedish nuclear programme, the safety assessment assumes a total of 6,000 canister corresponding to 12,000 tonnes of fuel

Fuel and canister process report for the safety assessment SR-Can

Energy Technology Data Exchange (ETDEWEB)

Werme, Lars (ed.)

2006-10-15

This report documents fuel and canister processes identified as relevant to the long-term safety of a KBS-3 repository. It forms an important part of the reporting of the safety assessment SR-Can. The detailed assessment methodology, including the role of the process report in the assessment, is described in the SR-Can Main report. The report is written by, and for, experts in the relevant scientific fields. It should though be possible for a generalist in the area of long-term safety assessments of geologic nuclear waste repositories to comprehend the contents of the report. The report is an important part of the documentation of the SR-Can project and an essential reference within the project, providing a scientifically motivated plan for the handling of geosphere processes. It is, furthermore, foreseen that the report will be essential for reviewers scrutinising the handling of geosphere issues in the SR-Can assessment. Several types of fuel will be emplaced in the repository. For the reference case with 40 years of reactor operation, the fuel quantity from boiling water reactors, BWR fuel, is estimated at 7,000 tonnes, while the quantity from pressurized water reactors, PWR fuel, is estimated at about 2,300 tonnes. In addition, 23 tonnes of mixed-oxide fuel (MOX) fuel of German origin from BWR and PWR reactors and 20 tonnes of fuel from the decommissioned heavy water reactor in Aagesta will be disposed of. To allow for future changes in the Swedish nuclear programme, the safety assessment assumes a total of 6,000 canister corresponding to 12,000 tonnes of fuel.

Making Distance Visible: Assembling Nearness in an Online Distance Learning Programme

Science.gov (United States)

Ross, Jen; Gallagher, Michael Sean; Macleod, Hamish

2013-01-01

Online distance learners are in a particularly complex relationship with the educational institutions they belong to (Bayne, Gallagher, & Lamb, 2012). For part-time distance students, arrivals and departures can be multiple and invisible as students take courses, take breaks, move into independent study phases of a programme, find work or…

Can technical laboratory skills be taught at a distance? An analysis of a semiconductor course taught at a distance via interactive technologies

Science.gov (United States)

Rao, Lalita

2000-10-01

This study investigated extending synchronous distance learning to teaching courses in the psychomotor domain in real-time, with immediate, direct feedback on technical skills performance from an instructor at a remote site via interactive technologies such as videoconferencing. This study focused on two research questions (1) can interactive distance learning technologies be used to teach technical and/or trouble shooting skills that fall under psychomotor domain? and, (2) to what degree can psychomotor skills be taught at a distance? A technical course, "RF Power PC 211L" from a technical and vocational institute was selected and the instructor who had no prior experience in teaching a distance learning course taught the course. Data on cognitive skills, psychomotor technical skills, attitudes and perceptions, demographics as well as boundary conditions on teaching psychomotor skills was gathered from both remote and the main campus. Instruments used for data gathering were final course grades, total points in laboratory exercise, pre and post course surveys, demographic survey and open-ended interviews with the instructor, student and review of instructor journal were used to address the two research questions. The main campus course was taught to the remote campus via distance learning technology in a distance learning format. The main technology used was videoconferencing. Both campus classrooms had the RF Trainer equipment. The rooms were set up to facilitate distance learning in the classroom. The instructor was present only at the main campus. The students on the remote campus were the experimental group. The experimental group participated in all course activities such as demonstrations, laboratory exercises, learning conceptual skills and tests only via distance. These students only had the benefit of laboratory assistant. The role of the laboratory assistant was to assist students/instructor as needed, ensure the safety of students and equipment and

Revisiting the safety of aspartame.

Science.gov (United States)

Choudhary, Arbind Kumar; Pretorius, Etheresia

2017-09-01

Aspartame is a synthetic dipeptide artificial sweetener, frequently used in foods, medications, and beverages, notably carbonated and powdered soft drinks. Since 1981, when aspartame was first approved by the US Food and Drug Administration, researchers have debated both its recommended safe dosage (40 mg/kg/d) and its general safety to organ systems. This review examines papers published between 2000 and 2016 on both the safe dosage and higher-than-recommended dosages and presents a concise synthesis of current trends. Data on the safe aspartame dosage are controversial, and the literature suggests there are potential side effects associated with aspartame consumption. Since aspartame consumption is on the rise, the safety of this sweetener should be revisited. Most of the literature available on the safety of aspartame is included in this review. Safety studies are based primarily on animal models, as data from human studies are limited. The existing animal studies and the limited human studies suggest that aspartame and its metabolites, whether consumed in quantities significantly higher than the recommended safe dosage or within recommended safe levels, may disrupt the oxidant/antioxidant balance, induce oxidative stress, and damage cell membrane integrity, potentially affecting a variety of cells and tissues and causing a deregulation of cellular function, ultimately leading to systemic inflammation. © The Author(s) 2017. Published by Oxford University Press on behalf of the International Life Sciences Institute. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com.

Nuclear safety and radiation protection report of the Fessenheim nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Fessenheim nuclear power plant (INB 75, Haut-Rhin, 68 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Gravelines nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Gravelines nuclear power plant (INB 96, 97 and 122, Nord (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Nuclear safety and radiation protection report of the Penly nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Penly nuclear power plant (INB 136 and 140, Seine-Maritime, 76 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Fessenheim nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Fessenheim nuclear power plant (INB 75, Haut-Rhin, 68 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Blayais nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Blayais nuclear power plant (INB 86 and 110, Gironde (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Gravelines nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Gravelines nuclear power plant (INB 96, 97 and 122, Nord (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Tricastin power plant - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Tricastin nuclear power plant (INB 87 and 88, Saint-Paul-Trois-Chateaux, Drome (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Nuclear safety and radiation protection report of the Gravelines nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Gravelines nuclear power plant (INB 96, 97 and 122, Nord (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Nuclear safety and radiation protection report of the Tricastin power plant - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Tricastin nuclear power plant (INB 87 and 88, Saint-Paul-Trois-Chateaux, Drome (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Nuclear safety and radiation protection report of the Penly nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Penly nuclear power plant (INB 136 and 140, Seine-Maritime, 76 (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Gravelines nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Gravelines nuclear power plant (INB 96, 97 and 122, Nord (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Nuclear safety and radiation protection report of the Gravelines nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Gravelines nuclear power plant (INB 96, 97 and 122, Nord (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Civaux nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Civaux nuclear power plant (INB 158 and 159, Vienne (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Blayais nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Blayais nuclear power plant (INB 86 and 110, Gironde (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Civaux nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Civaux nuclear power plant (INB 158 and 159, Vienne (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Birthday Cake Activity Structured Arrangement for Helping Children Determining Quantities

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatial thinking and number sense. Narrowing for this small research, we focused on one component of spatial thinking, that is structuring objects, and one component of number senses, that is cardinality by determining quantities. This study focused on a design research that was conducted in Indonesia in which we investigated pre-school children’s (between 2 and 3.5 years old ability in making structured arrangement and their ability to determine the quantities by looking at the arrangements. The result shows us that some of the children were able to make such arrangement. However, the children found difficulties either to determine quantities from those arrangements or to compare some structures to easily recognize number of objects.

Steiner Distance in Graphs--A Survey

OpenAIRE

Mao, Yaping

2017-01-01

For a connected graph $G$ of order at least $2$ and $S\\subseteq V(G)$, the \\emph{Steiner distance} $d_G(S)$ among the vertices of $S$ is the minimum size among all connected subgraphs whose vertex sets contain $S$. In this paper, we summarize the known results on the Steiner distance parameters, including Steiner distance, Steiner diameter, Steiner center, Steiner median, Steiner interval, Steiner distance hereditary graph, Steiner distance stable graph, average Steiner distance, and Steiner ...

Theoretical Principles of Distance Education.

Science.gov (United States)

Keegan, Desmond, Ed.

This book contains the following papers examining the didactic, academic, analytic, philosophical, and technological underpinnings of distance education: "Introduction"; "Quality and Access in Distance Education: Theoretical Considerations" (D. Randy Garrison); "Theory of Transactional Distance" (Michael G. Moore);…

THE DISTANCE TO M104

Energy Technology Data Exchange (ETDEWEB)

McQuinn, Kristen B. W. [University of Texas at Austin, McDonald Observatory, 2515 Speedway, Stop C1400 Austin, TX 78712 (United States); Skillman, Evan D. [Minnesota Institute for Astrophysics, School of Physics and Astronomy, 116 Church Street, SE, University of Minnesota, Minneapolis, MN 55455 (United States); Dolphin, Andrew E. [Raytheon Company, 1151 E. Hermans Road, Tucson, AZ 85756 (United States); Berg, Danielle [Center for Gravitation, Cosmology and Astrophysics, Department of Physics, University of Wisconsin Milwaukee, 1900 East Kenwood Boulevard, Milwaukee, WI 53211 (United States); Kennicutt, Robert, E-mail: kmcquinn@astro.as.utexas.edu [Institute for Astronomy, University of Cambridge, Madingley Road, Cambridge CB3 0HA (United Kingdom)

2016-11-01

M104 (NGC 4594; the Sombrero galaxy) is a nearby, well-studied elliptical galaxy included in scores of surveys focused on understanding the details of galaxy evolution. Despite the importance of observations of M104, a consensus distance has not yet been established. Here, we use newly obtained Hubble Space Telescope optical imaging to measure the distance to M104 based on the tip of the red giant branch (TRGB) method. Our measurement yields the distance to M104 to be 9.55 ± 0.13 ± 0.31 Mpc equivalent to a distance modulus of 29.90 ± 0.03 ± 0.07 mag. Our distance is an improvement over previous results as we use a well-calibrated, stable distance indicator, precision photometry in a optimally selected field of view, and a Bayesian maximum likelihood technique that reduces measurement uncertainties. The most discrepant previous results are due to Tully–Fisher method distances, which are likely inappropriate for M104 given its peculiar morphology and structure. Our results are part of a larger program to measure accurate distances to a sample of well-known spiral galaxies (including M51, M74, and M63) using the TRGB method.

The Distance to M51

Science.gov (United States)

McQuinn, Kristen. B. W.; Skillman, Evan D.; Dolphin, Andrew E.; Berg, Danielle; Kennicutt, Robert

2016-07-01

Great investments of observing time have been dedicated to the study of nearby spiral galaxies with diverse goals ranging from understanding the star formation process to characterizing their dark matter distributions. Accurate distances are fundamental to interpreting observations of these galaxies, yet many of the best studied nearby galaxies have distances based on methods with relatively large uncertainties. We have started a program to derive accurate distances to these galaxies. Here we measure the distance to M51—the Whirlpool galaxy—from newly obtained Hubble Space Telescope optical imaging using the tip of the red giant branch method. We measure the distance modulus to be 8.58 ± 0.10 Mpc (statistical), corresponding to a distance modulus of 29.67 ± 0.02 mag. Our distance is an improvement over previous results as we use a well-calibrated, stable distance indicator, precision photometry in a optimally selected field of view, and a Bayesian Maximum Likelihood technique that reduces measurement uncertainties. Based on observations made with the NASA/ESA Hubble Space Telescope, obtained from the Data Archive at the Space Telescope Science Institute, which is operated by the Association of Universities for Research in Astronomy, Inc., under NASA contract NAS 5-26555.

Are contemporary tourists consuming distance?

DEFF Research Database (Denmark)

Larsen, Gunvor Riber

2012. Background The background for this research, which explores how tourists represent distance and whether or not distance can be said to be consumed by contemporary tourists, is the increasing leisure mobility of people. Travelling for the purpose of visiting friends and relatives is increasing...... of understanding mobility at a conceptual level, and distance matters to people's manifest mobility: how they travel and how far they travel are central elements of their movements. Therefore leisure mobility (indeed all mobility) is the activity of relating across distance, either through actual corporeal...... metric representation. These representations are the focus for this research. Research Aim and Questions The aim of this research is thus to explore how distance is being represented within the context of leisure mobility. Further the aim is to explore how or whether distance is being consumed...

New Maximal Two-distance Sets

DEFF Research Database (Denmark)

Lisonek, Petr

1996-01-01

A two-distance set in E^d is a point set X inthe d-dimensional Euclidean spacesuch that the distances between distinct points in Xassume only two different non-zero values. Based on results from classical distance geometry, we developan algorithm to classify, for a given dimension, all maximal...... (largest possible)two-distance sets in E^d.Using this algorithm we have completed the full classificationfor all dimensions less than or equal to 7, andwe have found one set in E^8 whosemaximality follows from Blokhuis' upper bound on sizes of s-distance sets.While in the dimensions less than or equal to 6...

Common basis of establishing safety standards and other safety decision-making levels for different sources of health risk

International Nuclear Information System (INIS)

Demin, V.F.

2002-01-01

Current approaches in establishing safety standards and other decision-making levels for different sources of health risk are critically analysed. To have a common basis for this decision-making a specific risk index R is recommended. In the common sense R is quantitatively defined as LLE caused by the annual exposure to the risk source considered: R = annual exposure, damage (LLE) from the exposure unit. This common definition is also rewritten in specific forms for a set of different risk sources (ionising radiation, chemical pollutants, etc): for different risk sources the exposure can be measured with different quantities (the probability of death, the exposure dose, etc.). R is relative LLE: LLE in years referred to 1 year under the risk. The dimension of this value is [year/year]. In the statistical sense R is conditionally the share of the year, which is lost due to exposure to a risk source during this year. In this sense R can be called as the relative damage. Really lifetime years are lost after the exposure. R can be in some conditional sense considered as a dimensionless quantity. General safety standards R n for the public and occupational workers have been suggested in terms of this index: R n = 0.0007 and 0.01 accordingly. Secondary safety standards are derived for a number of risk sources (ionising radiation, environmental chemical pollutants, etc). Values of R n are chosen in such a way that to have the secondary radiation BSS being equivalent to the current one's. Other general and derived levels for safety decision-making are also proposed including the de-minimus levels. Their possible dependence on the national or regional health-demographic data (HDD) is considered. Such issues as the ways of the integration and averaging of risk indices considered through the national or regional HDD for different risk sources and the use of non-threshold linear exposure - response relationships for ionising radiation and chemical pollutants are analysed

Criticality safety evaluation of Rocky Flats Plant one-gallon shipping containers

International Nuclear Information System (INIS)

Briggs, J.B.

1991-02-01

Intraplant shipment of small quantities of plutonium and uranium at the Rocky Flats Plant (RFP) are made in one-gallon shipping containers. Criticality safety calculations have been performed to provide an analytical basis upon which handling, storage, and transportation limits on these containers are based. The calculations and results are documented in this report. This analysis was categorized as Quality Level A (according to the EG ampersand G Idaho Quality Manual) in that it is a service whose failure could cause undue risks to employees or public health and safety. It is intended to comply with NQA-1. 7 refs., 7 figs., 12 tabs

Does assisted driving behavior lead to safety-critical encounters with unequipped vehicles' drivers?

Science.gov (United States)

Preuk, Katharina; Stemmler, Eric; Schießl, Caroline; Jipp, Meike

2016-10-01

With Intelligent Transport Systems (e.g., traffic light assistance systems) assisted drivers are able to show driving behavior in anticipation of upcoming traffic situations. In the years to come, the penetration rate of such systems will be low. Therefore, the majority of vehicles will not be equipped with these systems. Unequipped vehicles' drivers may not expect the driving behavior of assisted drivers. However, drivers' predictions and expectations can play a significant role in their reaction times. Thus, safety issues could arise when unequipped vehicles' drivers encounter driving behavior of assisted drivers. This is why we tested how unequipped vehicles' drivers (N=60) interpreted and reacted to the driving behavior of an assisted driver. We used a multi-driver simulator with three drivers. The three drivers were driving in a line. The lead driver in the line was a confederate who was followed by two unequipped vehicles' drivers. We varied the equipment of the confederate with an Intelligent Transport System: The confederate was equipped either with or without a traffic light assistance system. The traffic light assistance system provided a start-up maneuver before a light turned green. Therefore, the assisted confederate seemed to show unusual deceleration behavior by coming to a halt at an unusual distance from the stop line at the red traffic light. The unusual distance was varied as we tested a moderate (4m distance from the stop line) and an extreme (10m distance from the stop line) parameterization of the system. Our results showed that the extreme parametrization resulted in shorter minimal time-to-collision of the unequipped vehicles' drivers. One rear-end crash was observed. These results provided initial evidence that safety issues can arise when unequipped vehicles' drivers encounter assisted driving behavior. We recommend that future research identifies counteractions to prevent these safety issues. Moreover, we recommend that system developers

Nuclear safety and radiation protection report of Chinon nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the facilities (INBs no. 94 (irradiated materials workshop), 99 (fuel storage facility), 107 and 132 (NPPs in operation), 133, 153 and 161 (NPPs under deconstruction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Modern licensing approaches for analysis of important to safety processes in Nuclear Power Plants

International Nuclear Information System (INIS)

Andreeva, M.; Groudev, P.; Pavlova, M.; Stoyanov, S.

2008-01-01

It is presented within the paper the modern approaches for analysis of important to safety assessment processes in Nuclear Power Plants, included Bulgarian Regulatory Agency's requirements for quantity assessment of these processes applying deterministic and probabilistic approaches for establishing and confirming the design basis and defence-in-depth effectiveness. (authors)

[Relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii].

Science.gov (United States)

Zhu, Hua; Teng, Jianbei; Cai, Yi; Liang, Jie; Zhu, Yilin; Wei, Tao

2011-12-01

To find out the relativity among starch quantity, polysaccharides content and total alkaloid content of Dendrobium loddigesii. Microscopy-counting process was applied to starch quantity statistics, sulfuric acid-anthrone colorimetry was used to assay polysaccharides content and bromocresol green colorimetry was used to assay alkaloid content. Pearson product moment correlation analysis, Kendall's rank correlation analysis and Spearman's concordance coefficient analysis were applied to study their relativity. Extremely significant positive correlation was found between starch quantity and polysaccharides content, and significant negative correlation between alkaloid content and starch quantity was discovered, as well was between alkaloid content and polysaccharides content.

Distance learning

Directory of Open Access Journals (Sweden)

Katarina Pucelj

2006-12-01

Full Text Available I would like to underline the role and importance of knowledge, which is acquired by individuals as a result of a learning process and experience. I have established that a form of learning, such as distance learning definitely contributes to a higher learning quality and leads to innovative, dynamic and knowledgebased society. Knowledge and skills enable individuals to cope with and manage changes, solve problems and also create new knowledge. Traditional learning practices face new circumstances, new and modern technologies appear, which enable quick and quality-oriented knowledge implementation. The centre of learning process at distance learning is to increase the quality of life of citizens, their competitiveness on the workforce market and ensure higher economic growth. Intellectual capital is the one, which represents the biggest capital of each society and knowledge is the key factor for succes of everybody, who are fully aware of this. Flexibility, openness and willingness of people to follow new IT solutions form suitable environment for developing and deciding to take up distance learning.

Non-Noether Conserved Quantity for Relativistic Nonholonomic System with Variable Mass

International Nuclear Information System (INIS)

Qiao Yongfen; Li Renjie; Ma Yongsheng

2005-01-01

Using form invariance under special infinitesimal transformations in which time is not variable, the non-Noether conserved quantity of the relativistic nonholonomic system with variable mass is studied. The differential equations of motion of the system are established. The definition and criterion of the form invariance of the system under infinitesimal transformations are studied. The necessary and sufficient condition under which the form invariance is a Lie symmetry is given. The condition under which the form invariance can be led to a non-Noether conserved quantity and the form of the conserved quantity are obtained. Finally, an example is given to illustrate the application of the result.

Radioactive safety analysis and assessment of waste rock pile site in uranium tailings

International Nuclear Information System (INIS)

Liu Changrong; Liu Zehua; Wang Zhiyong; Zhou Xinghuo

2007-01-01

Based on theoretical calculation and in-situ test results, distribution and emissions of radioactive nuclides of uranium tailings impoundment and waste rock pile sites are analyzed in this paper. It is pointed out that 222 Rn is the main nuclide of uranium tailings impoundment and waste rock pile site. Also 222 Rn is the main source term of public dose. 222 Rn concentrations in the atmospheric environment around and individual dose to Rn gradually decrease with increasing distances to uranium tailings impoundment and waste rock pile site. Based on in-situ tests on five uranium tailings impoundment and waste rock pile sites, a decisive method and safety protection distance are presented, which can be used to guide the validation and design of radioactive safety protection in uranium tailings impoundment and waste rock pile sites. (authors)

Exercise quantity-dependent muscle hypertrophy in adult zebrafish (Danio rerio).

Science.gov (United States)

Hasumura, Takahiro; Meguro, Shinichi

2016-07-01

Exercise is very important for maintaining and increasing skeletal muscle mass, and is particularly important to prevent and care for sarcopenia and muscle disuse atrophy. However, the dose-response relationship between exercise quantity, duration/day, and overall duration and muscle mass is poorly understood. Therefore, we investigated the effect of exercise duration on skeletal muscle to reveal the relationship between exercise quantity and muscle hypertrophy in zebrafish forced to exercise. Adult male zebrafish were exercised 6 h/day for 4 weeks, 6 h/day for 2 weeks, or 3 h/day for 2 weeks. Flow velocity was adjusted to maximum velocity during continual swimming (initial 43 cm/s). High-speed consecutive photographs revealed that zebrafish mainly drove the caudal part. Additionally, X-ray micro computed tomography measurements indicated muscle hypertrophy of the mid-caudal half compared with the mid-cranial half part. The cross-sectional analysis of the mid-caudal half muscle revealed that skeletal muscle (red, white, or total) mass increased with increasing exercise quantity, whereas that of white muscle and total muscle increased only under the maximum exercise load condition of 6 h/day for 4 weeks. Additionally, the muscle fiver size distributions of exercised fish were larger than those from non-exercised fish. We revealed that exercise quantity, duration/day, and overall duration were correlated with skeletal muscle hypertrophy. The forced exercise model enabled us to investigate the relationship between exercise quantity and skeletal muscle mass. These results open up the possibility for further investigations on the effects of exercise on skeletal muscle in adult zebrafish.

Fast Exact Euclidean Distance (FEED): A new class of adaptable distance transforms

NARCIS (Netherlands)

Schouten, Theo E.; van den Broek, Egon

2014-01-01

A new unique class of foldable distance transforms of digital images (DT) is introduced, baptized: Fast Exact Euclidean Distance (FEED) transforms. FEED class algorithms calculate the DT starting directly from the definition or rather its inverse. The principle of FEED class algorithms is

Fast Exact Euclidean Distance (FEED) : A new class of adaptable distance transforms

NARCIS (Netherlands)

Schouten, Theo E.; van den Broek, Egon L.

2014-01-01

A new unique class of foldable distance transforms of digital images (DT) is introduced, baptized: Fast Exact Euclidean Distance (FEED) transforms. FEED class algorithms calculate the DT startingdirectly from the definition or rather its inverse. The principle of FEED class algorithms is introduced,

BIRTHDAY CAKE ACTIVITY STRUCTURED ARRANGEMENT FOR HELPING CHILDREN DETERMINING QUANTITIES

Directory of Open Access Journals (Sweden)

Neni Mariana

2010-07-01

Full Text Available Few researches have been concerned about relation between children’s spatialthinking and number sense. Narrowing for this small research, we focused onone component of spatial thinking, that is structuring objects, and onecomponent of number senses, that is cardinality by determining quantities. Thisstudy focused on a design research that was conducted in Indonesia in which weinvestigated pre-school children’s (between 2 and 3.5 years old ability inmaking structured arrangement and their ability to determine the quantities bylooking at the arrangements. The result shows us that some of the children wereable to make such arrangement. However, the children found difficulties eitherto determine quantities from those arrangements or to compare some structuresto easily recognize number of objects.Keywords: structures, structured arrangement, cardinality DOI: http://dx.doi.org/10.22342/jme.1.1.790.53-70

Distance covariance for stochastic processes

DEFF Research Database (Denmark)

Matsui, Muneya; Mikosch, Thomas Valentin; Samorodnitsky, Gennady

2017-01-01

The distance covariance of two random vectors is a measure of their dependence. The empirical distance covariance and correlation can be used as statistical tools for testing whether two random vectors are independent. We propose an analog of the distance covariance for two stochastic processes...

Managing Time, Workload and Costs in Distance Education: Findings from a Literature Review of "Distances et Médiations des Savoirs" (Formerly "Distances et Savoirs")

Science.gov (United States)

Moeglin, Pierre; Vidal, Martine

2015-01-01

The purpose of this review, spanning over 12 years of publication of "Distances et Médiations des Savoirs" ("DMS"), formerly "Distance et Savoirs" ("DMS") (2003-2014), is guided by the question why and how French-speaking researchers addressed the issues of time, workload and costs in distance learning, and…

Nuclear safety and radiation protection report of Belleville-Sur-Loire nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 127 and 128). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of the Cruas-Meysse nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 111 and 112). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of Dampierre-En-Burly nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 84 and 85). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of Nogent-Sur-Seine nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 129 and 130). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports

Science.gov (United States)

2017-12-01

by the Army Acquisition Executive contains the following language . As a recently delegated Acquisition Category IC program, the AH-64E Apache...Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis, Project Leader Margaret L. Giles David M. Tate I...F E N S E A N A L Y S E S IDA Paper P-8490 Complexity in an Unexpected Place: Quantities in Selected Acquisition Reports Gregory A. Davis

Critical Points in Distance Learning System

Directory of Open Access Journals (Sweden)

Airina Savickaitė

2013-08-01

Full Text Available Purpose – This article presents the results of distance learning system analysis, i.e. the critical elements of the distance learning system. The critical points of distance learning are a part of distance education online environment interactivity/community process model. The most important is the fact that the critical point is associated with distance learning participants. Design/methodology/approach – Comparative review of articles and analysis of distance learning module. Findings – A modern man is a lifelong learner and distance learning is a way to be a modern person. The focus on a learner and feedback is the most important thing of learning distance system. Also, attention should be paid to the lecture-appropriate knowledge and ability to convey information. Distance system adaptation is the way to improve the learner’s learning outcomes. Research limitations/implications – Different learning disciplines and learning methods may have different critical points. Practical implications – The information of analysis could be important for both lecturers and students, who studies distance education systems. There are familiar critical points which may deteriorate the quality of learning. Originality/value – The study sought to develop remote systems for applications in order to improve the quality of knowledge. Keywords: distance learning, process model, critical points. Research type: review of literature and general overview.

Prenatal Phthalate Exposures and Anogenital Distance in Swedish Boys

Science.gov (United States)

Carlstedt, Fredrik; Jönsson, Bo AG.; Lindh, Christian H.; Jensen, Tina K.; Bodin, Anna; Jonsson, Carin; Janson, Staffan; Swan, Shanna H.

2014-01-01

Background: Phthalates are used as plasticizers in soft polyvinyl chloride (PVC) and in a large number of consumer products. Because of reported health risks, diisononyl phthalate (DiNP) has been introduced as a replacement for di(2-ethylhexyl) phthalate (DEHP) in soft PVC. This raises concerns because animal data suggest that DiNP may have antiandrogenic properties similar to those of DEHP. The anogenital distance (AGD)—the distance from the anus to the genitals—has been used to assess reproductive toxicity. Objective: The objective of this study was to examine the associations between prenatal phthalate exposure and AGD in Swedish infants. Methods: AGD was measured in 196 boys at 21 months of age, and first-trimester urine was analyzed for 10 phthalate metabolites of DEP (diethyl phthalate), DBP (dibutyl phthalate), DEHP, BBzP (benzylbutyl phthalate), as well as DiNP and creatinine. Data on covariates were collected by questionnaires. Results: The most significant associations were found between the shorter of two AGD measures (anoscrotal distance; AGDas) and DiNP metabolites and strongest for oh-MMeOP [mono-(4-methyl-7-hydroxyloctyl) phthalate] and oxo-MMeOP [mono-(2-ethyl-5-oxohexyl) phthalate]. However, the AGDas reduction was small (4%) in relation to more than an interquartile range increase in DiNP exposure. Conclusions: These findings call into question the safety of substituting DiNP for DEHP in soft PVC, particularly because a shorter male AGD has been shown to relate to male genital birth defects in children and impaired reproductive function in adult males and the fact that human levels of DiNP are increasing globally. Citation: Bornehag CG, Carlstedt F, Jönsson BA, Lindh CH, Jensen TK, Bodin A, Jonsson C, Janson S, Swan SH. 2015. Prenatal phthalate exposures and anogenital distance in Swedish boys. Environ Health Perspect 123:101–107; http://dx.doi.org/10.1289/ehp.1408163 PMID:25353625

Connecting long distance: semantic distance in analogical reasoning modulates frontopolar cortex activity.

Science.gov (United States)

Green, Adam E; Kraemer, David J M; Fugelsang, Jonathan A; Gray, Jeremy R; Dunbar, Kevin N

2010-01-01

Solving problems often requires seeing new connections between concepts or events that seemed unrelated at first. Innovative solutions of this kind depend on analogical reasoning, a relational reasoning process that involves mapping similarities between concepts. Brain-based evidence has implicated the frontal pole of the brain as important for analogical mapping. Separately, cognitive research has identified semantic distance as a key characteristic of the kind of analogical mapping that can support innovation (i.e., identifying similarities across greater semantic distance reveals connections that support more innovative solutions and models). However, the neural substrates of semantically distant analogical mapping are not well understood. Here, we used functional magnetic resonance imaging (fMRI) to measure brain activity during an analogical reasoning task, in which we parametrically varied the semantic distance between the items in the analogies. Semantic distance was derived quantitatively from latent semantic analysis. Across 23 participants, activity in an a priori region of interest (ROI) in left frontopolar cortex covaried parametrically with increasing semantic distance, even after removing effects of task difficulty. This ROI was centered on a functional peak that we previously associated with analogical mapping. To our knowledge, these data represent a first empirical characterization of how the brain mediates semantically distant analogical mapping.

Symmetries and conserved quantities in geodesic motion

International Nuclear Information System (INIS)

Hojman, S.; Nunez, L.; Patino, A.; Rago, H.

1986-01-01

Recently obtained results linking several constants of motion to one (non-Noetherian) symmetry to the problem of geodesic motion in Riemannian space-times are applied. The construction of conserved quantities in geodesic motion as well as the deduction of geometrical statements about Riemannian space-times are achieved

ADM pseudotensors, conserved quantities and covariant conservation laws in general relativity

International Nuclear Information System (INIS)

Fatibene, L.; Ferraris, M.; Francaviglia, M.; Lusanna, L.

2012-01-01

The ADM formalism is reviewed and techniques for decomposing generic components of metric, connection and curvature are obtained. These techniques will turn out to be enough to decompose not only Einstein equations but also covariant conservation laws. Then a number of independent sets of hypotheses that are sufficient (though not necessary) to obtain standard ADM quantities (and Hamiltonian) from covariant conservation laws are considered. This determines explicitly the range in which standard techniques are equivalent to covariant conserved quantities. The Schwarzschild metric in different coordinates is then considered, showing how the standard ADM quantities fail dramatically in non-Cartesian coordinates or even worse when asymptotically flatness is not manifest; while, in view of their covariance, covariant conservation laws give the correct result in all cases. - Highlights: ► In the paper ADM conserved quantities for GR are obtained from augmented conservation laws. ► Boundary conditions for this to be possible are considered and compared with the literature. ► Some different forms of Schwarzschild solutions are considered as simple examples of different boundary conditions.

Equivalence of massive propagator distance and mathematical distance on graphs

International Nuclear Information System (INIS)

Filk, T.

1992-01-01

It is shown in this paper that the assignment of distance according to the massive propagator method and according to the mathematical definition (length of minimal path) on arbitrary graphs with a bound on the degree leads to equivalent large scale properties of the graph. Especially, the internal scaling dimension is the same for both definitions. This result holds for any fixed, non-vanishing mass, so that a really inequivalent definition of distance requires the limit m → 0

Analytical Model for Passing Sight Distance Design Criteria of Two-Lane Roads in Sri Lanka

Directory of Open Access Journals (Sweden)

Mampearachchi W. K.

2018-03-01

Full Text Available For a safe overtaking manoeuvre on two-lane highways, drivers need a sufficient sight distance along the roadway, but it depends on the traffic environment. To provide an adequate Passing Sight Distance (PSD, a number of models have been proposed since the initial model introduced by American Association of State Highways and Transport Officials (AASHTO in 1954. It is a current design practice in Sri Lanka as well, however, not validated for local traffic conditions. This paper will present an alternative PSD model and an evaluation of AASHTO model for national highway design. Experiment was based on GPS data collection. In conclusion, PSD demand was satisfied by AASHTO PSD under mix traffic conditions, but not the safety concerns for speeds greater than 80 km/h, while alternative model successful for all speeds.

Studies on quantity and composition of dairy cow excreta

International Nuclear Information System (INIS)

Peschke, H.

1982-01-01

After feeding a lactating dairy cow a day ration completely enriched with 15 N, the quantities of feces and urine were registered over a period of ten days and put into proportion to the animal mass. The fecal dry matter was put into proportion to the dry matter of the fodder by means of 15 N analysis the N excretion with the excreta was determined concerning quantity and time. Selected feces and urine charges were used to produce a slurry model. The content of nutritive elements of the initial components and of the organic fertilizer are discussed. (author)

Validity of the concept of absorbed dose as a physical quantity

International Nuclear Information System (INIS)

Tada, Jun-Ichiro; Katoh, Kazuaki.

1995-01-01

The concept of the 'absorbed dose' of ionizing radiation is scrutinized from physical point of view. It is shown that the concept and definition of the quantity in the ICRU system is disqualified as a physical quantity and the absorbed dose can not always be a 'measure of cause' in describing causality relation between radiation and effects on matter. The current absorbed dose depends even on the energy that have already been brought out from the matter, contrary to the intention of introducing the quantity. Trials to remove these difficulties are made. However, it is also shown there still exists an essential problem that cannot be solved by improving the formulation. (author)

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Directory of Open Access Journals (Sweden)

Gaku Fukunaga

Full Text Available The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Property of Fluctuations of Sales Quantities by Product Category in Convenience Stores.

Science.gov (United States)

Fukunaga, Gaku; Takayasu, Hideki; Takayasu, Misako

2016-01-01

The ability to ascertain the extent of product sale fluctuations for each store and locality is indispensable to inventory management. This study analyzed POS data from 158 convenience stores in Kawasaki City, Kanagawa Prefecture, Japan and found a power scaling law between the mean and standard deviation of product sales quantities for several product categories. For the statistical domains of low sales quantities, the power index was 1/2; for large sales quantities, the power index was 1, so called Taylor's law holds. The value of sales quantities with changing power indixes differed according to product category. We derived a Poissonian compound distribution model taking into account fluctuations in customer numbers to show that the scaling law could be explained theoretically for most of items. We also examined why the scaling law did not hold in some exceptional cases.

Language distance and tree reconstruction

International Nuclear Information System (INIS)

Petroni, Filippo; Serva, Maurizio

2008-01-01

Languages evolve over time according to a process in which reproduction, mutation and extinction are all possible. This is very similar to haploid evolution for asexual organisms and for the mitochondrial DNA of complex ones. Exploiting this similarity, it is possible, in principle, to verify hypotheses concerning the relationship among languages and to reconstruct their family tree. The key point is the definition of the distances among pairs of languages in analogy with the genetic distances among pairs of organisms. Distances can be evaluated by comparing grammar and/or vocabulary, but while it is difficult, if not impossible, to quantify grammar distance, it is possible to measure a distance from vocabulary differences. The method used by glottochronology computes distances from the percentage of shared 'cognates', which are words with a common historical origin. The weak point of this method is that subjective judgment plays a significant role. Here we define the distance of two languages by considering a renormalized edit distance among words with the same meaning and averaging over the two hundred words contained in a Swadesh list. In our approach the vocabulary of a language is the analogue of DNA for organisms. The advantage is that we avoid subjectivity and, furthermore, reproducibility of results is guaranteed. We apply our method to the Indo-European and the Austronesian groups, considering, in both cases, fifty different languages. The two trees obtained are, in many respects, similar to those found by glottochronologists, with some important differences as regards the positions of a few languages. In order to support these different results we separately analyze the structure of the distances of these languages with respect to all the others

Language distance and tree reconstruction

Science.gov (United States)

Petroni, Filippo; Serva, Maurizio

2008-08-01

Languages evolve over time according to a process in which reproduction, mutation and extinction are all possible. This is very similar to haploid evolution for asexual organisms and for the mitochondrial DNA of complex ones. Exploiting this similarity, it is possible, in principle, to verify hypotheses concerning the relationship among languages and to reconstruct their family tree. The key point is the definition of the distances among pairs of languages in analogy with the genetic distances among pairs of organisms. Distances can be evaluated by comparing grammar and/or vocabulary, but while it is difficult, if not impossible, to quantify grammar distance, it is possible to measure a distance from vocabulary differences. The method used by glottochronology computes distances from the percentage of shared 'cognates', which are words with a common historical origin. The weak point of this method is that subjective judgment plays a significant role. Here we define the distance of two languages by considering a renormalized edit distance among words with the same meaning and averaging over the two hundred words contained in a Swadesh list. In our approach the vocabulary of a language is the analogue of DNA for organisms. The advantage is that we avoid subjectivity and, furthermore, reproducibility of results is guaranteed. We apply our method to the Indo-European and the Austronesian groups, considering, in both cases, fifty different languages. The two trees obtained are, in many respects, similar to those found by glottochronologists, with some important differences as regards the positions of a few languages. In order to support these different results we separately analyze the structure of the distances of these languages with respect to all the others.

16 CFR 500.7 - Net quantity of contents, method of expression.

Science.gov (United States)

2010-01-01

... expression. The net quantity of contents shall be expressed in terms of weight or mass, measure, numerical... consumers. The net quantity of contents statement shall be in terms of fluid measure if the commodity is liquid, or in terms of weight or mass if the commodity is solid, semi-solid, or viscous, or a mixture of...

A small quantity of sodium arsenite will kill large cull hardwoods

Science.gov (United States)

Francis M. Rushmore

1956-01-01

Although it is well known that sodium arsenite is an effective silvicide, forestry literature contains little information about the minimum quantities of this chemical that are required to kill large cull trees. Such information would be of value because if small quantities of a chemical will produce satisfactory results, small holes or frills in the tree will hold it...

A dispersion safety factor for LNG vapor clouds

Energy Technology Data Exchange (ETDEWEB)

Vílchez, Juan A. [TIPs – Trámites, Informes y Proyectos, SL, Llenguadoc 10, 08030 Barcelona (Spain); Villafañe, Diana [Centre d’Estudis del Risc Tecnològic (CERTEC), Universitat Politècnica de Catalunya, Diagonal 647, 08028 Barcelona, Catalonia (Spain); Casal, Joaquim, E-mail: joaquim.casal@upc.edu [Centre d’Estudis del Risc Tecnològic (CERTEC), Universitat Politècnica de Catalunya, Diagonal 647, 08028 Barcelona, Catalonia (Spain)

2013-02-15

Highlights: ► We proposed a new parameter: the dispersion safety factor (DSF). ► DSF is the ratio between the distance reached by the LFL and that reached by the visible cloud. ► The results for the DSF agree well with the evidence from large scale experiments. ► Two expressions have been proposed to calculate DSF as a function of H{sub R}. ► The DSF may help in indicating the danger of ignition of a LNG vapor cloud. -- Abstract: The growing importance of liquefied natural gas (LNG) to global energy demand has increased interest in the possible hazards associated with its storage and transportation. Concerning the event of an LNG spill, a study was performed on the relationship between the distance at which the lower flammability limit (LFL) concentration occurs and that corresponding to the visible contour of LNG vapor clouds. A parameter called the dispersion safety factor (DSF) has been defined as the ratio between these two lengths, and two expressions are proposed to estimate it. During an emergency, the DSF can be a helpful parameter to indicate the danger of cloud ignition and flash fire.

A dispersion safety factor for LNG vapor clouds

International Nuclear Information System (INIS)

Vílchez, Juan A.; Villafañe, Diana; Casal, Joaquim

2013-01-01

Highlights: ► We proposed a new parameter: the dispersion safety factor (DSF). ► DSF is the ratio between the distance reached by the LFL and that reached by the visible cloud. ► The results for the DSF agree well with the evidence from large scale experiments. ► Two expressions have been proposed to calculate DSF as a function of H R . ► The DSF may help in indicating the danger of ignition of a LNG vapor cloud. -- Abstract: The growing importance of liquefied natural gas (LNG) to global energy demand has increased interest in the possible hazards associated with its storage and transportation. Concerning the event of an LNG spill, a study was performed on the relationship between the distance at which the lower flammability limit (LFL) concentration occurs and that corresponding to the visible contour of LNG vapor clouds. A parameter called the dispersion safety factor (DSF) has been defined as the ratio between these two lengths, and two expressions are proposed to estimate it. During an emergency, the DSF can be a helpful parameter to indicate the danger of cloud ignition and flash fire

Interactive Distance Learning in Connecticut.

Science.gov (United States)

Pietras, Jesse John; Murphy, Robert J.

This paper provides an overview of distance learning activities in Connecticut and addresses the feasibility of such activities. Distance education programs have evolved from the one dimensional electronic mail systems to the use of sophisticated digital fiber networks. The Middlesex Distance Learning Consortium has developed a long-range plan to…

Uncertainty analysis of thermal quantities measurement in a centrifugal compressor

Science.gov (United States)

Hurda, Lukáš; Matas, Richard

2017-09-01

Compressor performance characteristics evaluation process based on the measurement of pressure, temperature and other quantities is examined to find uncertainties for directly measured and derived quantities. CFD is used as a tool to quantify the influences of different sources of uncertainty of measurements for single- and multi-thermocouple total temperature probes. The heat conduction through the body of the thermocouple probe and the heat-up of the air in the intake piping are the main phenomena of interest.

Nuclear safety and radiation protection report of the Tricastin nuclear facility (BCOT) - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the Tricastin operational hot base facility (INB no. 157, Bollene, Vaucluse (FR)), a nuclear workshop for storage and maintenance and qualification operations on some EdF equipments. Then, the nuclear safety and radiation protection measures taken regarding the facility are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, if some, are reported as well as the effluents discharge in the environment. Finally, the management of the radioactive materials and wastes generated by the facility is presented and sorted by type of waste, quantities and type of conditioning. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Motivation in Distance Leaming

Directory of Open Access Journals (Sweden)

Daniela Brečko

1996-12-01

Full Text Available It is estimated that motivation is one of the most important psychological functions making it possible for people to leam even in conditions that do not meet their needs. In distance learning, a form of autonomous learning, motivation is of outmost importance. When adopting this method in learning an individual has to stimulate himself and take learning decisions on his or her own. These specific characteristics of distance learning should be taken into account. This all different factors maintaining the motivation of partici­pants in distance learning are to be included. Moreover, motivation in distance learning can be stimulated with specific learning materials, clear instructions and guide-lines, an efficient feed back, personal contact between tutors and parti­cipants, stimulating learning letters, telephone calls, encouraging letters and through maintaining a positive relationship between tutor and participant.

Measuring nanocurie quantities of tritium bred in metallic lithium and lithium oxide samples

International Nuclear Information System (INIS)

Bertone, P.C.

1985-01-01

The LBM program requires that nanocurie quantities of tritium, bred in both lithium oxide pellets and lithium samples, be measured with an uncertainty not exceeding + or - 6%. Two methods of accurately measuring nanocurie quantities of tritium bred in LBM lithium oxide pellets and one method of accurately measuring nanocurie quantities of tritium bred in lithium samples are described. Potential errors associated with these tritium measurement techniques are also discussed

An Online Network Tool for Quality Information to Answer Questions about Occupational Safety and Health: Usability and Applicability

NARCIS (Netherlands)

Rhebergen, M.D.F.; Hulshof, C.T.J.; Lenderink, A.F.; van Dijk, F.J.H.

2010-01-01

ABSTRACT: BACKGROUND: Common information facilities do not always provide the quality information needed to answer questions on health or health-related issues, such as Occupational Safety and Health (OSH) matters. Barriers may be the accessibility, quantity and readability of information. Online

Machine learning enhanced optical distance sensor

Science.gov (United States)

Amin, M. Junaid; Riza, N. A.

2018-01-01

Presented for the first time is a machine learning enhanced optical distance sensor. The distance sensor is based on our previously demonstrated distance measurement technique that uses an Electronically Controlled Variable Focus Lens (ECVFL) with a laser source to illuminate a target plane with a controlled optical beam spot. This spot with varying spot sizes is viewed by an off-axis camera and the spot size data is processed to compute the distance. In particular, proposed and demonstrated in this paper is the use of a regularized polynomial regression based supervised machine learning algorithm to enhance the accuracy of the operational sensor. The algorithm uses the acquired features and corresponding labels that are the actual target distance values to train a machine learning model. The optimized training model is trained over a 1000 mm (or 1 m) experimental target distance range. Using the machine learning algorithm produces a training set and testing set distance measurement errors of learning. Applications for the proposed sensor include industrial scenario distance sensing where target material specific training models can be generated to realize low <1% measurement error distance measurements.

An approach for estimating the radiological significance of a hypothetical major nuclear accident over long distance transboundary scales

Energy Technology Data Exchange (ETDEWEB)

Mitrakos, D., E-mail: dimitris.mitrakos@eeae.gr; Potiriadis, C.; Housiadas, C.

2016-04-15

Highlights: • Actions may be warranted after a major nuclear accident even at long distances. • Distance may not be the decisive parameter for longer term radiological impact. • Remote impact may vary orders of magnitude depending on the meteorological conditions. • The potential impact can be assessed using computationally inexpensive calculations. - Abstract: After the Fukushima accident important initiatives were taken in European level to enhance the nuclear safety level of the existing and planned nuclear reactors, such as the so-called nuclear “stress-tests” and the amendment of the Nuclear Safety Directive. A recent work of HERCA and WENRA focused on the need for a more consistent and harmonized response in a transboundary context in case of a hypothetical major nuclear accident in Europe. Such an accident, although very improbable, cannot be totally excluded and so, should be considered in emergency preparedness arrangements among the various European countries. In case of a hypothetical severe Fukushima-like accident in Europe, the role of the neighboring countries may be important, since the authorities should be able to provide information and advice to the government and the public, but also can contribute to the overall assessment of the situation be their own means. In this work we assess the radiological significance of a hypothetical major nuclear accident for distances longer than 300 km that are not typically covered by the internationally accepted emergency planning zones. The approach is simple and computationally inexpensive, since it is based on the calculation of only a few release scenarios at dates selected within a whole year on the basis of bounding the deposition levels at long distances in relation to the occurrence of precipitation. From the calculated results it is evident that distance is not the only decisive parameter in estimating the potential radiological significance of a severe nuclear accident. The hypothetical

Food quantity affects the sensitivity of Daphnia to road salt.

Science.gov (United States)

Brown, Arran H; Yan, Norman D

2015-04-07

Road deicing operations have raised chloride (Cl) levels in many temperate lakes in Europe and North America. These lakes vary widely in trophic status, but to date, no one has quantified the interaction between food quantity and road salt toxicity. We examined the effects of food quantity (particulate algal C concentration (C)) on the chronic toxicity of Cl to Daphnia in soft-water bioassays. There was a strong positive linear relationship (r(2) = 0.92 for NaCl and r(2) = 0.96 for CaCl2) between food quantity and Cl LC50. As food quantity increased from 0.2 to 1.0 mg C/L (levels characteristic of oligotrophic to eutrophic lakes, respectively), the chronic Cl LC50 increased from 55.7 to 284.8 mg Cl/L. Salt type (NaCl or CaCl2) did not affect the Cl LC50, Daphnia life history parameters, or the intrinsic rate of population increase (r). The life history parameter most sensitive to Cl was neonate production. Cl did not inhibit egg production, nor was the maternal lipid investment in eggs changed, but egg viability and the subsequent release of live neonates decreased as Cl levels increased and food decreased. Our results suggest the trophic status of lakes should be considered when assessing ecological threat from Cl.

Price effects of changing quantities supplied at the integrated european fish market

DEFF Research Database (Denmark)

Nielsen, Max; Smit, Jos; Guillen, Jordi

2012-01-01

to be −1.1. This implies that price flexibilities previously estimated for single European countries underestimate price changes at the European level caused by quantity changes. Results indicate that changing quantities can increase revenues from individual species with large own-price flexibilities...

Nuclear safety and radiation protection report of the Tricastin operational hot base nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the Tricastin operational hot base facility (INB no. 157, Bollene, Vaucluse (FR)), a nuclear workshop for storage and maintenance and qualification operations on some EdF equipments. Then, the nuclear safety and radiation protection measures taken regarding the facility are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if some, are reported as well as the effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facility is presented and sorted by type of waste, quantities and type of conditioning. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions

Automated Decisional Model for Optimum Economic Order Quantity Determination Using Price Regressive Rates

Science.gov (United States)

Roşu, M. M.; Tarbă, C. I.; Neagu, C.

2016-11-01

The current models for inventory management are complementary, but together they offer a large pallet of elements for solving complex problems of companies when wanting to establish the optimum economic order quantity for unfinished products, row of materials, goods etc. The main objective of this paper is to elaborate an automated decisional model for the calculus of the economic order quantity taking into account the price regressive rates for the total order quantity. This model has two main objectives: first, to determine the periodicity when to be done the order n or the quantity order q; second, to determine the levels of stock: lighting control, security stock etc. In this way we can provide the answer to two fundamental questions: How much must be ordered? When to Order? In the current practice, the business relationships with its suppliers are based on regressive rates for price. This means that suppliers may grant discounts, from a certain level of quantities ordered. Thus, the unit price of the products is a variable which depends on the order size. So, the most important element for choosing the optimum for the economic order quantity is the total cost for ordering and this cost depends on the following elements: the medium price per units, the stock cost, the ordering cost etc.

Thermodynamic quantities for the Klein–Gordon equation

Indian Academy of Sciences (India)

We study some thermodynamic quantities for the Klein–Gordon equation with a linear plus inverselinear, scalar potential. We obtain the energy eigenvalues with the help of the quantization rule from the biconfluent Heun's equation.We use a method based on the Euler–MacLaurin formula to analytically compute thethermal ...

19 CFR 351.409 - Differences in quantities.

Science.gov (United States)

2010-04-01

... DUTIES Calculation of Export Price, Constructed Export Price, Fair Value, and Normal Value § 351.409... comparing export price or constructed export price with normal value, the Secretary will make a reasonable... section 773(a)(6)(C)(i) of the Act.) (b) Sales with quantity discounts in calculating normal value. The...

16 CFR 1.23 - Quantity limit rules.

Science.gov (United States)

2010-01-01

... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Quantity limit rules. 1.23 Section 1.23 Commercial Practices FEDERAL TRADE COMMISSION ORGANIZATION, PROCEDURES AND RULES OF PRACTICE GENERAL... Robinson-Patman Act. These rules have the force and effect of law. [32 FR 8444, June 13, 1967. Redesignated...

Radiation safety training for industrial irradiators: What are we trying to accomplish?

International Nuclear Information System (INIS)

Smith, M.A.

1998-01-01

Radiation safety training at an industrial irradiator facility takes a different approach than the traditional methods and topics used at other facilities. Where the more routine industrial radiation users focus on standard training topics of contamination control, area surveys, and the traditional dogma of time, distance, and shielding, radiation safety in an industrial irradiation facility must be centered on preventing accidents. Because the primary methods for accomplishing that goal are engineering approaches such as safety system interlocks, training provided to facility personnel should address system operation and emergency actions. This presents challenges in delivering radiation safety training to an audience of varied educational and technical background where little to no commercially available training material specific to this type of operation exists

Nuclear safety and radiation protection report of the Chinon nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the facilities (INBs no. 94 (irradiated materials workshop), 99 (fuel storage facility), 107 and 132 (NPPs in operation), 133, 153 and 161 (NPPs under deconstruction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Bugey nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the facilities (INBs no. 78, 89 (NPPs in operation), 465 (NPP under deconstruction), 102 (fuel storage facility), and 173 (radioactive waste conditioning and storage facility under construction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Bugey nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the facilities (INBs no. 78, 89 (NPPs in operation), 465 (NPP under deconstruction), 102 (fuel storage facility), and 173 (radioactive waste conditioning and storage facility under construction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Chinon nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the facilities (INBs no. 94 (irradiated materials workshop), 99 (fuel storage facility), 107 and 132 (NPPs in operation), 133, 153 and 161 (NPPs under deconstruction)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Urgency of increasing the quantity and quality of student creativity program

Science.gov (United States)

Sarmini; Prasetya, Ketut; Nadiroh, Ulin

2018-01-01

Student creativity is very important to improve the quality and quantity. The purpose of this paper is to identify the quality and quantity of the Student Creativity Program. The method in this research is exploratory study. The subjects taken are the leaders of deans and vice deans at the State University of Surabaya. Data collection techniques used are kusioner. The result of this research is creativity program in student is very important. Not only improve the quality and quantity of creativity, but also affect the image of the institution. It is necessary to have written rules on the regulations on the Student Creativity Program and to take a comprehensive and comprehensive approach, and to organize the budget is the main thing.

Uncertainties of exposure-related quantities in mammographic x-ray unit quality control

International Nuclear Information System (INIS)

Gregory, Kent J.; Pattison, John E.; Bibbo, Giovanni

2006-01-01

Breast screening programs operate in many countries with mammographic x-ray units subject to stringent quality control tests. These tests include the evaluation of quantities based on exposure measurements, such as half value layer, automatic exposure control reproducibility, average glandular dose, and radiation output rate. There are numerous error sources that contribute to the uncertainty of these exposure-related quantities, some of which are unique to the low energy x-ray spectrum produced by mammographic x-ray units. For each of these exposure-related quantities, the applicable error sources and their magnitudes vary, depending on the test equipment used to make the measurement, and whether or not relevant corrections have been applied. This study has identified and quantified a range of error sources that may be used to estimate the combined uncertainty of these exposure-related quantities, given the test equipment used and corrections applied. The uncertainty analysis uses methods described by the International Standards Organization's Guide to the Expression of Uncertainty in Measurement. Examples of how these error sources combine to give the uncertainty of the exposure-related quantities are presented. Using the best test equipment evaluated in this study, uncertainties of the four exposure-related quantities at the 95% confidence interval were found to be ±1.6% (half value layer), ±0.0008 (automatic exposure control reproducibility), ±2.3% (average glandular dose), and ±2.1% (radiation output rate). In some cases, using less precise test equipment or failing to apply corrections, resulted in uncertainties more than double in magnitude

Multidemand Multisource Order Quantity Allocation with Multiple Transportation Alternatives

Directory of Open Access Journals (Sweden)

Jun Gang

2015-01-01

Full Text Available This paper focuses on a multidemand multisource order quantity allocation problem with multiple transportation alternatives. To solve this problem, a bilevel multiobjective programming model under a mixed uncertain environment is proposed. Two levels of decision makers are considered in the model. On the upper level, the purchaser aims to allocate order quantity to multiple suppliers for each demand node with the consideration of three objectives: total purchase cost minimization, total delay risk minimization, and total defect risk minimization. On the lower level, each supplier attempts to optimize the transportation alternatives with total transportation and penalty costs minimization as the objective. In contrast to prior studies, considering the information asymmetry in the bilevel decision, random and fuzzy random variables are used to model uncertain parameters of the construction company and the suppliers. To solve the bilevel model, a solution method based on Kuhn-Tucker conditions, sectional genetic algorithm, and fuzzy random simulation is proposed. Finally, the applicability of the proposed model and algorithm is evaluated through a practical case from a large scale construction project. The results show that the proposed model and algorithm are efficient in dealing with practical order quantity allocation problems.

Study on Fuzzy Comprehensive Evaluation Model for the Safety of Mine Belt Conveyor

Directory of Open Access Journals (Sweden)

Gong Xiaoyan

2017-01-01

Full Text Available To improve the situation of the frequent failures of mine belt conveyor during operation, a model was used to evaluate the safety of mine belt conveyor. Based on the foundation of collecting and analyzing a large quantity of fault information of belt conveyor in the nationwide coal mine, the fault tree model of belt conveyor has been built, then the safety evaluation index system was established by analyzing and removing some secondary indicators. Furthermore, the weighted value of safety evaluation indexs was determined by analytic hierarchy process(AHP, and the single factor fuzzy evaluation matrix was constructed by experts grading method. Additionally, the model was applied in evaluating the security of belt conveyor in Nanliang coal mine. The results shows the security level is recognized to the “general”, which means that this model can be adopted widely in evaluating the safety of mine belt conveyor.

PROBABILISTIC MODEL FOR AIRPORT RUNWAY SAFETY AREAS

Directory of Open Access Journals (Sweden)

Stanislav SZABO

2017-06-01

Full Text Available The Laboratory of Aviation Safety and Security at CTU in Prague has recently started a project aimed at runway protection zones. The probability of exceeding by a certain distance from the runway in common incident/accident scenarios (take-off/landing overrun/veer-off, landing undershoot is being identified relative to the runway for any airport. As a result, the size and position of safety areas around runways are defined for the chosen probability. The basis for probability calculation is a probabilistic model using statistics from more than 1400 real-world cases where jet airplanes have been involved over the last few decades. Other scientific studies have contributed to understanding the issue and supported the model’s application to different conditions.

Autonomous Highway Systems Safety and Security

OpenAIRE

Sajjad, Imran

2017-01-01

Automated vehicles are getting closer each day to large-scale deployment. It is expected that self-driving cars will be able to alleviate traffic congestion by safely operating at distances closer than human drivers are capable of and will overall improve traffic throughput. In these conditions, passenger safety and security is of utmost importance. When multiple autonomous cars follow each other on a highway, they will form what is known as a cyber-physical system. In a general setting, t...

Safety study of the coupling of a VHTR with a hydrogen production plant

International Nuclear Information System (INIS)

Bertrand, F.; Germain, T.; Bentivoglio, F.; Bonnet, F.; Moyart, Q.; Aujollet, P.

2011-01-01

Highlights: → The paper deals with safety issues of the coupling of a VHTR with a H 2 production plant. → Internal incidents/accidents in the coupling system have been studied with the CATHARE2 code. → Transient studies have indicated a substantial grace delay when the VHTR faces the H 2 plant disturbances. → Hydrogen release and combustion leads to safety distances of about 100 m. → No showstopper has been put in evidence regarding the feasibility of the VHTR/H 2 plant coupling. - Abstract: The present paper deals with specific safety issues resulting from the coupling of a nuclear reactor (very high temperature reactor, VHTR) with a hydrogen production plant (HYPP). The first part is devoted to the safety approach consisting in taking into account the safety standards and rules dedicated to the nuclear facility as well as those dedicated to the process industry. This approach enabled two main families of events to be distinguished: the so-called internal events taking place in the coupling circuit (transients, breaks in pipes and in heat exchangers) and the external events able to threat the integrity of the various equipments (in particular the VHTR containment and emergency cooling system) that could result from accidents in the HYPP. By considering a hydrogen production by means of the iodine/sulfur (IS) process, the consequences of the both families of events aforementioned have been assessed in order to provide an order of magnitude of the effects of the incidents and accidents and also in order to propose safety provisions to mitigate these effects when it is necessary. The study of transients induced by a failure of a part of the HYPP has shown the possibility to keep the part of the HYPP unaffected by the transient under operation by means of an adapted regulation set. Moreover, the time to react in case of transfer of corrosive products in the VHTR containment has been assessed as well as the thermohydraulic loading that would experience the

Long-distance calls in Neotropical primates

Directory of Open Access Journals (Sweden)

Oliveira Dilmar A.G.

2004-01-01

Full Text Available Long-distance calls are widespread among primates. Several studies concentrate on such calls in just one or in few species, while few studies have treated more general trends within the order. The common features that usually characterize these vocalizations are related to long-distance propagation of sounds. The proposed functions of primate long-distance calls can be divided into extragroup and intragroup ones. Extragroup functions relate to mate defense, mate attraction or resource defense, while intragroup functions involve group coordination or alarm. Among Neotropical primates, several species perform long-distance calls that seem more related to intragroup coordination, markedly in atelines. Callitrichids present long-distance calls that are employed both in intragroup coordination and intergroup contests or spacing. Examples of extragroup directed long-distance calls are the duets of titi monkeys and the roars and barks of howler monkeys. Considerable complexity and gradation exist in the long-distance call repertoires of some Neotropical primates, and female long-distance calls are probably more important in non-duetting species than usually thought. Future research must focus on larger trends in the evolution of primate long-distance calls, including the phylogeny of calling repertoires and the relationships between form and function in these signals.

Robustness of Distance-to-Default

DEFF Research Database (Denmark)

Jessen, Cathrine; Lando, David

2013-01-01

Distance-to-default is a remarkably robust measure for ranking firms according to their risk of default. The ranking seems to work despite the fact that the Merton model from which the measure is derived produces default probabilities that are far too small when applied to real data. We use...... simulations to investigate the robustness of the distance-to-default measure to different model specifications. Overall we find distance-to-default to be robust to a number of deviations from the simple Merton model that involve different asset value dynamics and different default triggering mechanisms....... A notable exception is a model with stochastic volatility of assets. In this case both the ranking of firms and the estimated default probabilities using distance-to-default perform significantly worse. We therefore propose a volatility adjustment of the distance-to-default measure, that significantly...

Quantitative and Qualitative Analysis of Nutrition and Food Safety Information in School Science Textbooks of India

Science.gov (United States)

Subba Rao, G. M.; Vijayapushapm, T.; Venkaiah, K.; Pavarala, V.

2012-01-01

Objective: To assess quantity and quality of nutrition and food safety information in science textbooks prescribed by the Central Board of Secondary Education (CBSE), India for grades I through X. Design: Content analysis. Methods: A coding scheme was developed for quantitative and qualitative analyses. Two investigators independently coded the…

Nuclear safety and radiation protection report of the Chooz nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Chooz nuclear power plant (Ardennes (FR)): 2 PWR reactors in operation (Chooz B, INB 139 and 144) and one partially dismantled PWR reactor (Chooz A, INB 163). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary followed by the viewpoint of the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Paluel nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Paluel nuclear power plant (INB no. 103 - Paluel 1, no. 104 - Paluel 2, no. 114 - Paluel 3 and no. 115 - Paluel 4, Cany-Barville - Seine-Maritime (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document ends with a glossary and no recommendation from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Paluel nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Paluel nuclear power plant (INB no. 103 - Paluel 1, no. 104 - Paluel 2, no. 114 - Paluel 3 and no. 115 - Paluel 4, Cany-Barville - Seine-Maritime (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Golfech nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Golfech nuclear power plant (INB 135 and 142, Tarn-et-Garonne (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Cattenom nuclear facilities - 2011

International Nuclear Information System (INIS)

2012-01-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Cattenom nuclear power plant (INB 124, 125, 126 and 137, Moselle (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2011, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Cattenom nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Cattenom nuclear power plant (INB 124, 125, 126 and 137, Moselle (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Golfech nuclear facilities - 2010

International Nuclear Information System (INIS)

2011-06-01

This safety report was established under the article 21 of the French law no. 2006-686 of June 13, 2006 relative to nuclear safety and information transparency. It presents, first, the facilities of the Golfech nuclear power plant (INB 135 and 142, Tarn-et-Garonne (FR)). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2010, are reported as well as the radioactive and non-radioactive (chemical, thermal) effluents discharge in the environment. Finally, The radioactive materials and wastes generated by the facilities are presented and sorted by type of waste, quantities and type of conditioning. Other environmental impacts (noise, microbial proliferation in cooling towers) are presented with their mitigation measures. Actions in favour of transparency and public information are presented as well. The document concludes with a glossary and a list of recommendations from the Committees for health, safety and working conditions. (J.S.)

Nuclear safety and radiation protection report of the Belleville-sur-Loire nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 127 and 128). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Belleville-sur-Loire nuclear facilities - 2014

International Nuclear Information System (INIS)

2015-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 127 and 128). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2014, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

The safety case for a HLW repository in Opalinus clay: aims, methodology, first results

International Nuclear Information System (INIS)

Zuidema, Piet

2002-01-01

Piet Zuidema (Nagra, Switzerland) described the development of the safety case for a high level waste repository in Opalinus clay in which canisters would be placed in large vaults. The current phase of work was concerned with demonstrating the feasibility of the disposal concept. The Safety Case is taken to mean a set of arguments to support a statement that the proposed facility will meet relevant safety criteria and will include arguments giving the basis for confidence that those arguments are correct and properly taking account of uncertainties. The safety strategy was concerned both with the inherent robustness of the disposal concept and the adequacy of the assessment capability. As regards the former, the arguments being advanced were primarily qualitative. Key issues in terms of the documentation of the Safety Case were traceability and transparency of information, including how to ensure that key arguments did not become obscured because of the need to make available very large quantities of information

Nuclear safety and radiation protection report of the Dampierre-en-Burly nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 84 and 85). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of Saint-Alban Saint-Maurice nuclear facilities - 2012

International Nuclear Information System (INIS)

2013-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 119 and 120). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2012, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix. (J.S.)

Nuclear safety and radiation protection report of the Nogent-sur-Seine nuclear facilities - 2013

International Nuclear Information System (INIS)

2014-01-01

This safety report was established in accordance with articles L. 125-15 and L. 125-16 of the French environmental code. It presents, first, the NPPs (INBs no. 129 and 130). Then, the nuclear safety and radiation protection measures taken regarding the facilities are reviewed: nuclear safety definition, radiation protection of intervening parties, safety and radiation protection improvement paths, crisis management, external and internal controls, technical situation of facilities, administrative procedures in progress. The incidents and accidents which occurred in 2013, if any, are reported as well as the radioactive and non-radioactive effluents discharge in the environment. Finally, the radioactive materials and wastes generated by the facility are presented (type of waste, quantities, conditioning process). The document concludes with a presentation of the actions of communication and public information made by the direction of the facility. A glossary and the list of recommendations from the Committees for health, safety and working conditions are given in appendix

Nuclear safety and radiation protection report of the Dampierre-en-Burly nuclear facilities - 2014