Low and intermediate waste disposal facilities safety assessment is comprised of several steps from site selection , construction and operation to post-closure performance assessment. This is a multidisciplinary and complex task , and can not be analyzed by one expert only. This high complexity can lead to ambiguity and vagueness in information and consequently in the decisionmaking process. In order to make the decision process clear and objective, there is the need to provide the decision makers with a clear and comprehensive picture of the whole process and, at the same time, simple and easily understandable by the public. This paper suggests the development of an inference system based on fuzzy decisionmaking methodology. Fuzzy logic tools are specially suited to deal with ambiguous data by using language ...
This report, the fifth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1989. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications.
This report, the seventh in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1991. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications.
This report, the seventh in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1991. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications.
This report, the sixth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1990. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications.
This report, the fourth in a series of annual reports, was prepared in response to Congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during 1988. The goal of this office is to ensure that safety-related research provides the technical bases for rulemaking and for related decisions in support of NRC licensing and inspection activities. This research is necessary to make certain that the regulations that are imposed on licensees provide an adequate margin of safety so as to protect the health and safety of the public. This report describes both the direct contributions to scientific and technical knowledge with regard to nuclear safety and their regulatory applications.
In the past few months, there has been public discussion relating to a new perspective on blood safety and specifically upon measures to prevent or discourage donation by individuals with a diagnosis of myalgic encephalopathy-chronic fatigue syndrome. This reflects an intriguing interplay between science, public health and public concern and illustrates some of the difficulties of makingdecisions in the face of uncertainty and inadequate information.
The Atomic Energy commission of Syria (AECS) is nominated by Syrian legislation as the regulatory authority in respect of radiation protection and safety and security of radioactive sources. In addition AECS is providing a wide range of Technical Services (TS) through its various departments. In this paper, the cooperation and coordination between the regulatory authority and the providers of technical services in Syria are described. The adjustment of the regulatory programme as to make maximal use of the available technical resources is presented. It was shown that this relationship does not jeopardize the effective independency of the regulatory authority which is maintained by keeping the regulatory decisions based on pure regulatory considerations. (author)
BackgroundHow socio-demographic factors influence women's autonomy in decisionmaking on health care including purchasing goods and visiting family and relatives are very poorly...Full Text Available
A schematic diagram of the decisionmaking process for air pollution control equipment for the conversion of a fossil-fired generating unit from oil to coal is presented and explained.
Allowed outage time (AOT), which is required by the technical specification of nuclear power plants (NPPs), has been determined on the basis of deterministic analysis or engineering judgment. AOT is defined as the time for which safety related components can remain inoperable before a plant state is changed. Recently, plants' operating experiences and probabilistic safety assessment (PSA) results show that the AOT could be optimized. Foreign NPPs licensees have changed their technical specifications including AOT using PSA techniques. In 1998, U.S. NRC issued the regulatory guides on risk informed decision-making and technical specification changes, and these are Reg. Guide 1.174, and 1.177. The US NRC accepted AOT extension proposals including the safety injection tank (SIT) and low pressure safety injection system (LPSI) for the ABB-CE designed plants. This paper discusses interim ...
Effective and efficient strategic decisionmaking is the backbone for the success of a business organization. These decisionmaking processes, used among its competitors in a particular industry, determine whether the business will continue to survive or not. In this research, fuzzy logic (FL) concept and game theory are being used to model strategic decisionmaking processes by business organizations. Competition between business organizations is viewed as a game with each business organization as a player. A player formulates his own decisions by making his strategic moves based on uncertain information. This is the information he has about the opponents with respect to prevailing or anticipated market demand, cost of production, marketing, consolidation efforts and some other business v...
Since 1992, the fruitful collaboration of the Russian and Western-European technical support organizations (TSOs) is being continued due to the support of the European Commission. There are two main areas of activities. The first one is more of methodological assistance and enhancing RF TSOs capabilities to support Rostekhnadzor decisionmaking process. Experience and knowledge acquired in this area projects increase RF TSOs capabilities regarding a wide spectrum of safety related issues assessment, in particular safety analyses, reactor vessel embrittlement, application of 'leak before break' concept, severe accident and accident management, fire risk evaluation, etc. The second area is focused on licensing related assessments of EC financed on site assistance projects (modernisations). This area projects promote implementation in Russia a licensing process based on a technical dialogue between ...
An extension of TOPSIS, a multi-criteria interval-valued intuitionistic fuzzy decisionmaking technique, to a group decision environment is investigated, where inter-dependent or interactive characteristics among criteria and preference of decision makers are taken into account. To get a broad view of the techniques used, first, some operational laws on interval-valued intuitionistic fuzzy values are introduced. Based on these operational laws, a generalized interval-valued intuitionistic fuzzy geometric aggregation operator is proposed which is used to aggregate decision makers? opinions in group decisionmaking process. In addition, some of its properties are discussed. Then Choquet integral-based Hamming distance between interval-valued intuitionistic fuzzy values is defined. Combining ...
This report includes the issuances received during the specified period from the Commission (CLI), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judges (AU), the Directors` Decisions (DD), and the Decisions on Petitions for Rulemaking (DPRM).
This report includes the issuances received during the specified period from the Commission (CLI), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judges (ALJ), the Directors Decisions (DD), and the Decisions on Petitions for Rulemaking (DPRM).
Behavioral economics has captured the interest of scholars and the general public by demonstrating ways in which individuals makedecisions that appear irrational. While increasing attention is being focused on the implications of this research for the design of risk-reducing policies, less attention has been paid to how it affects the economic valuation of policy consequences. This article considers the latter issue, reviewing the behavioral economics literature and discussing its implications for the conduct of benefit-cost analysis, particularly in the context of environmental, health, and safety regulations. We explore three concerns: using estimates of willingness to pay or willingness to accept compensation for valuation, considering the psychological aspects of risk when valuing mortality-risk reductions, and discounting future consequences. In each case, we take the perspective that analysts should avoid ...
BackgroundThe aim of this study is to examine how clinicians and patients negotiate clinical need and treatment decisions within a context of finite resources. Dental implant treatment...Full Text Available
One of the major decisions that germ cells make during their development is whether to differentiate into oocytes or sperm. In mice, the germ cells’ decision to develop as male or female depends...Full Text Available
Information needs that arise when clinicians use clinical information systems often go unresolved, forcing clinicians to defer decisions or make them with incomplete knowledge. My research characterizes...Full Text Available
In developing severe accident management strategies, an engineering decision would be made based on the available data and information that are vague, imprecise and uncertain by nature. These sorts of vagueness and uncertainty are due to lack of knowledge for the severe accident sequences of interest. The fuzzy set theory offers a possibility of handling these sorts of data and information. In this paper, the possibility to apply the decision-making method based on fuzzy set theory to the evaluation of the accident management strategies at a nuclear power plant is scrutinized. The fuzzy decision-making method uses linguistic variables and fuzzy numbers to represent the decision-maker's subjective assessments for the decision alternatives according to the decision criteria. The fuzzy mean operator is used to aggregate the ...
This report includes the issuances received during the specified period from the Commission, the Atomic Safety and Licensing Appeal Boards, the Atomic Safety and Licensing Boards, the Administrative Law Judge, the Directors' Decisions, and the Denials of Petitions for Rulemaking.
This report includes the issuances received during the specified period from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Directors' Decisions (DD), and the Denials of Petitions for Rulemaking (DPRM).
This report includes the issuances received during the specified period from the Commission (CLl), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), The Directors' Decisions (DD), and the Denials of Petitions For Rulemaking (DPRM).
Multi-criteria group decisionmaking (MCGDM) aims to support preference-based decision over the available alternatives that are characterized by multiple criteria in a group. To increase the level of overall satisfaction for the final decision across the group and deal with uncertainty in decision process, a fuzzy MCGDM process (FMP) model is established in this study. This FMP model can also aggregate both subjective and objective information under multi-level hierarchies of criteria and evaluators. Based on the FMP model, a fuzzy MCGDM decision support system (called Decider) is developed, which can handle information expressed in linguistic terms, boolean values, as well as numeric values to assess and rank a set of alternatives within a group of decision makers. Real applications indic...
Jan 12, 2010 ... Visual simulation of offshore liquefied natural gas (lng) terminals in a decision-making context. Baird, Brian E.; Sheppard, Stephen R. J.; ...
... Abstract : Fifty-nine Grenada veterans currently assigned to the 82nd Airborne Division and the 1st and 2nd Battalions of the 75th Ranger Regiment ...
The importance of designating criteria for diagnosing dementia lies in its implications for clinical treatment, research, caregiving, and decision-making. Dementia diagnosis in Huntington's...Full Text Available
The development of online communication systems related to prevention, decisionmaking, and coping with cancer has outpaced theoretical attention to the attributes that appeal to system...Full Text Available
The relations between nuclear energy availability and nuclear plant safety are analyzed in the particular cases of naval propulsion nuclear boilers (aircraft carriers, submarines): safety objectives, present and potential risk analysis, optimization of the availability-safety couple, at the design stage and during operation (procedural rules related to the boiler state, real time decisions). 6 fig., 1 tab.
The objective of SCK-CEN's R and D programme on decision strategy research are (1) to support and advise the Belgian authorities on specific problems concerning existing and potential hazards from exposure to ionising radiation, both in normal and emergency situations; (2) to perform research on relevant topics that might have an important impact on decisionmaking related to nuclear applications, including social and economic sciences. Main achievements in this area in 1999 are described.
A range of lessons have been identified from previous attempts to implement long term radioactive waste management policy in the UK and internationally. Many of these relate to the way the decision-making process is undertaken and the fact that there needs to be an open, transparent process that enables continuous stakeholder involvement. Nirex believes that using the SEA and EIA frameworks will help to incorporate the lessons learned into the future decision-making process relating to long-term radioactive waste management.
This publication identifies conditions which affect (either increase or decrease) public concern for and political acceptance of the development and implementation of programmes for geological disposal of long lived radioactive waste. It also looks at how interested citizens can be associated in the decisionmaking process in such a way that their input enriches the outcome of a more socially robust and sustainable solution. The publication also considers how to optimize risk management, addressing the needs and expectations of the public and of other relevant stakeholders. Factors of relevance for societal acceptance conditions are identified for the different stages of a repository programme and implementation process, from policy development to the realization of the repository itself. Further, they are described and analysed through case studies from several countries, illustrating the added value of broadening the technical dimension with ...
A featfinding committee of the German Federal Parliament in July 1980 recommended to perform a ''risk-oriented study'' of the SNR-300, the German 300 MW fast breeder prototype reactor being under construction in Kalkar. The main aim of this study was to allow a comparative safety evaluation between the SNR-300 and a modern PWR, thus to prepare a basis for a political decision on the SNR-300. Methods and main results of the study are presented in this paper. In the first step of the risk analysis six groups of accidents have been identified which may initiate core destruction. These groups comprise all conceivable courses, potentially leading to core destruction. By reliability analyses, expected frequency of each group has been calculated. In the accident analysis potential failure modes of the reactor tank have been investigated. Core destruction may be accompanied by the release of significant amounts of mechanical energy. The primary coolant ...
There are two kinds of uncertainties in safety assessment of engineering structures. One is of the nature of randomness, and the other fuzziness. Fuzzy uncertainties exist in defining certain structural performances, conditions, parameters, and their interrelationships. The theory of fuzzy sets should be employed to cope with the fuzzy uncertainties. In this paper, a general definition for structural failure considering the fuzzy uncertainties is introduced firstly. Failure of the structure is modelled by a fuzzy event, and described by the membership function. The limit state surface is then replaced by a fuzzy limit state zone, in which every point represents a state belonging to the failure with a certain degree of membership. Then a fuzzy optimization problem for solving the reliability index is formulated. In classical structural reliability theory, the reliability index is defined by the minimum distance from the limit state surface to the origin of the ...
Using an efficient criterion in selection of fuzzy conditional attributes (i.e. expanded attributes) is important for generation of fuzzy decision trees. Given a fuzzy information system (FIS), fuzzy conditional attributes play a crucial role in fuzzy decisionmaking. Besides, different fuzzy conditional attributes have different influences on decisionmaking, and some of them may be more important than the others. Two well-known criteria employed to select expanded attributes are fuzzy classification entropy and classification ambiguity, both of which essentially use the ratio of uncertainty to measure the significance of fuzzy conditional attributes. Based on fuzzy-rough technique, this paper proposes a new criterion, in which expanded attributes are selected by using significance of fuz...
ObjectiveComputerized physician order entry with clinical decision support has been shown to improve medication safety in adult inpatients, but few data are available regarding its...Full Text Available
Although past research has reported the benefits of intuition in new product decision-making (i.e., higher quality product; enhanced customer satisfaction), intuition has largely been studied as an individual phenomenon and little work has examined the role of intuition on new product development (NPD) project teams. Furthermore, in a turbulent environment, NPD project teams may rely more on intuitive judgments, and other factors such as experience and stress may also influence the relationship between team intuition and team decisionmaking. Drawing from the organizational design literature on creativity in decisionmaking, this study builds a conceptual model of NPD team intuition and its effect on the team's ability to generate creative new products. We then derive hypotheses regarding ...
In this paper a new fuzzy decision-making procedure is developed. Two levels of weightings, called upper and lower weights, are proposed to calculate the fuzzy weightings of different criteria. The preference table is introduced to calculate the upper and lower weights. Also a new method is developed to determine the expected preference values of different alternatives. These values are used for generating the priority list of alternatives. The procedure is applied for providing an emergency electric power distribution, scheduling time table. The IEEE 14-bus standard system and a 14-bus system with four power plants are considered as case studies. Using fuzzy decision-making procedure, the regions with more priorities are more connected to the distribution net, while the maximum consumption criterion is also reasonably respected. (author)
The comments are divided into three parts. Section 2 relates generally to programs for which greater effort or emphasis is needed. Section 3 provides specific comments on the proposed programs in each Decision Unit and, in most cases, for individual Subelements within each Decision Unit. Specific recommendations regarding the Research Program Support Budget are given in Section 4.
This paper details the development of a decontamination approach for the West Valley Demonstration Project (WVDP), Decontamination Project Plan (Plan). The WVDP is operated by West Valley Nuclear Services Company (WVNSCO), a subsidiary of Westinghouse Government and Environmental Services, and its parent companies Washington Group International and British Nuclear Fuels Limited (BNFL). The WVDP is a waste management effort being conducted by the United States Department of Energy (DOE) at the site of the only commercial nuclear fuel reprocessing facility to have operated in the United States. This facility is part of the Western New York Nuclear Service Center (WNYNSC), which is owned by the New York State Energy Research and Development Authority (NYSERDA). As authorized by Congress in 1980 through the West Valley Demonstration Project Act (WVDP Act, Public Law 96-368), the DOE's primary mission at the WVDP is to solidify high-level liquid nuclear waste safely; transport the ...
... Tschantz, Performance Evaluation of Constructed Urban Stormwater Detention Ponds in the Knoxville Area, proceedings and presentation to International Conference on DecisionMaking in Urban and Civil Engineering, Lyon, France, November 22, 2000. B.A. Tschanz, Current Problems, Practices, and ...
Game theory models of animal contests make many non-mutually exclusive predictions, complicating empirical tests. These predictions regard the relationship between contest parameters and fighting ability,...Full Text Available
Randomized clinical trials are designed with stopping boundaries to guide data monitoring committees with their decisionmaking concerning ongoing trials. In particular, when extremely positive results...Full Text Available
The likelihood that past experience will produce correct guides to current practice depends on the signal-to-noise ratio for the clinical problem of interest. If the signal-to-noise ratio is high, the...Full Text Available
The status of the concept of controlling the quality of physicians is reviewed as are studies that have been done on methods to measure and improve quality. The conclusions are dismal given the rhetoric...Full Text Available
Typically, modern economics has steered away from the analysis of sociological and psychological factors and has focused on narrow behavioural assumptions in which expectations are formed on the basis...Full Text Available
Journal editorials are an important medium for communicating information about medical innovations. Evaluative statements contained in editorials pertain to the innovation's technical merits, as well...Full Text Available
ObjectivesThis feasibility study developed and pilot tested an intervention to: (1) increase knowledge about prostate cancer (CaP) screening; and (2) promote self-efficacy...Full Text Available
The contribution under consideration spans a wide curve from the first deadly accident of motorized aviation in the year 1908 up to newer tendencies of the so-called team resources management on observation points and control stations in order to pursue fundamental questions in man-machine systems. A continuous differentiation in the consideration of the factor human beings in complex technical systems is described. This is illustrated by the example of concepts for leadership, communication and decisionmaking on observation points and control stations.
As a generalization of fuzzy set, hesitant fuzzy set is a very useful tool in situations where there are some difficulties in determining the membership of an element to a set caused by a doubt between a few different values. The aim of this paper is to develop a series of aggregation operators for hesitant fuzzy information. We first discuss the relationship between intutionistic fuzzy set and hesitant fuzzy set, based on which we develop some operations and aggregation operators for hesitant fuzzy elements. The correlations among the aggregation operators are further discussed. Finally, we give their application in solving decisionmaking problems.
The purpose of this paper is to inform commercial building designers about an energy analysis tool which can aid them in making appropriate decisions about daylighting. The energy nomographs are an energy design tool which calculate the annual energy consumption of commercial buildings, including lighting, heating, cooling, domestic hot water, fans, pumps, and miscellaneous items. This paper specifically discusses the daylighting aspects of the tool. The calculation procedure is presented with an example to explain how this design tool can be used to make good energy decisions early in the design process.
We study uncertainties surrounding competition on business networks and board games. We investigate these uncertainties using concepts of fuzzy logic and game theory. We investigate how the payoff of the players is affected by a number of factors. These include the level of connectivity or number of links, the number of competitors, possible constraints on the networks and on the boards, as well as choice of strategy adopted by competitors. We introduce one fuzzy player in the game. This player uses fuzzy rules to make strategic decisions. We introduce learning to train and analyze how the fuzzy player adapts over time during the game.
This paper contributes to an understanding of pharmacogenomics-in-the-making by foregrounding a regulatory setting in which these technologies must be situated: decision-making about pharmaceutical reimbursement. Health care assessment organizations have been introduced in many countries to systematically address the issue of health care coverage. Using the example of Sweden, the process of deciding reimbursement status is shown to hinge on the creation of stable and clinically feasible categories of patients, diseases and drug responses. Through a series of analogous examples concerning conventional pharmaceuticals, it is argued that current mechanisms for categorizing reimbursable drugs could be upset when pharmacogenomic advances provide a means of making patients more specific objects ...
This report includes the issuances received during April 1984 from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Directors' Decisions (DD), and the Denials of Petitions for Rulemaking (DPRM).
This report includes the issuances received during the specified period from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Directors' Decisions (DD), and the Denials of Petitions For Rulemaking (DPRM).
This report includes the issuances received during the specified period from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Director's Decisions (DD), and the Denials of Petitions For Rulemaking (DPRM).
This report includes the issuances received during November, 1983, from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Directors' Decisions (DD), and the Denials of Petitions for Rulemaking (DPRM).
This report includes the issuances received during January 1984 from the Commission (CLI), the Atomic Safety and Licensing Appeal Boards (ALAB), the Atomic Safety and Licensing Boards (LBP), the Administrative Law Judge (ALJ), the Directors' Decisions (DD), and the Denials of Petitions for Rulemaking (DPRM).
Determination of the suitability of the site for WIPP is only the first major phase in the evaluation of the radiological impact of the repository on the public health and safety. The Environmental Evaluation Group (EEG) will continue to independently review the design of the facility, the operational procedures, the criteria for packaging and shipment of the waste, the plans, procedures and results of the WIPP experiments, emergency preparedness, adherence to EPA and pertinent NRC regulations, and other important features of the project. EEG has concluded from existing evidence that the Los Medanos site for the WIPP project has been characterized in sufficient detail to warrant confidence in the validation of the site for the permanent emplacement of approximately 6 million cubic feet of defense transuranic waste. This conclusion is based on the assumption that the maximum surface dose rate for the unshielded remote-handled transuranic waste canisters will be 100 ...
Summary Many important moral decisions, particularly at the policy level, require the evaluation of choices involving outcomes of variable magnitude and probability. Many economic decisions involve the same problem. It is not known whether and to what extent these structurally isomorphic decisions rely on common neural mechanisms. Subjects undergoing fMRI evaluated the moral acceptability of sacrificing a single life to save a larger group of variable size and probability of dying without action. Paralleling research on economic decisionmaking, the ventromedial prefrontal cortex and ventral striatum were specifically sensitive to the "expected moral value" of actions, i.e., the expected number of lives lost/saved. Likewise, the right anterior insula was specifically sensitive to outcome p...
This is the seventh report by the Advisory Committee on Reactor Safeguards (ACRS) in response to the Congressional requirement for an annual report on the Nuclear Regulatory Commission (NRC) Reactor Safety Research Program. As previously requested by the Congress, the timing of this report has been adjusted to enable the ACRS to address the proposed budget for FY 1985 that has been submitted to the Congress by the President. Part I is a compilation of our comments and recommendations regarding the NRC Safety Research Program budget for FY 1985. It is intended to serve as an Executive Summary. Part II is divided into eight chapters, each of which represents a Decision Unit of the NRC research program. In each chapter, specific comments are included on the research involved in the Decision Unit, an assessment of priorities, and recommendations regarding new directions and levels of funding.
This is the sixth report by the Advisory Committee on Reactor Safeguards (ACRS) that has been prepared in response to the Congressional requirement for an annual report on the Nuclear Regulatory Commission (NRC) Reactor Safety Research Program. Part I is a compilation of our general comments and recommendations regarding the NRC Safety Research Program, and includes budget recommendations and an identification of matters of special importance that deserve increased emphasis. It is intended to serve as an Executive Summary. Part II is divided into ten chapters, each of which represents a Decision Unit of the NRC research program. In each chapter, specific comments are included on the research involved in the Decision Unit, an assessment of priorities, and recommendations regarding new directions and levels of funding.
The FFTF Standby Plan, Revision 0, provides changes to the major elements and project baselines to maintain the FFTF plant in a standby condition and to continue washing sodium from irradiated reactor fuel. The Plan is consistent with the Memorandum of Decision approved by the Secretary of Energy on January 17, 1997, which directed that FFTF be maintained in a standby condition to permit the Department to make a decision on whether the facility should play a future role in the Department of Energy`s dual track tritium production strategy. This decision would be made in parallel with the intended December 1998 decision on the selection of the primary, long- term source of tritium. This also allows the Department to review the economic and technical feasibility of using the FFTF to produce isotopes for the medical community. Formal direction has been received from DOE-RL and Fluor ...
The paper considers research carried out on the topic of life cycle (LC) modelling of industrial processes with emphasis upon energy utilisation and gaseous emissions. The aim of the work is to investigate existing LC assessment codes, in particular for their outputs and decisionmaking potential, and to develop the characteristics of new software as appropriate. The paper focuses on a comparison of two methods for LC modelling: use of ''SimaPro 5'' with ECO-indicators and logical-information modelling. The considered approaches require attention to dynamic modelling having features for decisionmaking; for example, in areas of costs, sensitivity analysis and optimisation of LC process parameters to economically reduce the total environmental load. Brick making is chosen as an energy intensive process for model application. (orig.)
The Belgian radioactive waste management agency NIRAS/ONDRAF has undertaken a comparative assessment study on long-term waste management options for the high-level and/or long-lived radioactive waste that should be managed as a result of the use of nuclear energy in Belgium. This study is one of the supportive documents to a Strategic Environmental Assessment (SEA) process initiated end of 2008 and geared towards a decision in principle by the Belgian Government in 2010 on the long-term management of such radioactive waste. NIRAS/ONDRAF, together with Belgian and international research organisations, has developed a reference option for such high-level and long-lived radioactive waste, called Category B and C Waste, consisting of the disposal of such waste in a clay formation [SAFIR-2]. More than 30 years of R and D have been undertaken resulting, among others, in the underground research facility HADES, though the decision in principle by ...
Internationally, on-line maintenance (OLM) of nuclear power plants under the operation is prevailed to enhance nuclear safety and economics. In recent years, Korea Hydro and Nuclear Power Co. Ltd. (KHNP) is eager to apply OLM. Ministry of Education, Science and Technology (MEST) has established the related technology development program as an item of 'Overall Planning on Nuclear Safety(2010-2014)' through acceptance to the request of KHNP in 2009. OLM is defined as maintenance that is performed with the main generator connected to the grid. In other words, it means a preventive maintenance to be implemented during the allowable outage time (AOT) with ignoring inoperability of safety-related equipment listed in the technical specifications. The Korea Institute of Nuclear Safety (KINS) is developing the assessment technology of safety concerns for OLM under the auspices of MEST. Draft ...
Projects have become a way of getting things done, and have moved increasingly toward achieving qualitative goals. In this article on video game development, the opportunity is taken to relate some particular observations on creative projects and their management. The essential aspects of this approach are its incorporation of individual and group creativity into its foundation, a Lindblomian process of decisionmaking, and a substitution of a time of regular introspection for milestones. Application depends upon the ability to have interim developments available for group examination and fixing a suitable time interval to make such assessments. The approach would seem applicable to a range of possibilities, including film making, script writing, architectural rendering, and equipment desi...
Digests and indexes for issuances of the Commission (CLI), the Atomic Safety and Licensing Board Panel (LBP), the Administrative Law Judges (ALJ), the Directors` Decisions (DD), and the Decision on Petitions for Rulemaking (DPRM) are presented in this document. These digests and indexes are intended to serve as a guide to the issuances. Information elements common to the cases heard and ruled upon are: case name (owner(s) of facility); full text reference (volume and pagination); issuance number; issues raised by apellants; legal citations (cases, regulations, and statutes); name of facility, docket number; subject matter of issues and/or rulings; type of hearing (operating license, operating license amendment, etc.); type of issuance (memorandum, order, decision, etc.).
A fuzzy-decision-making procedure is applied to find the optimal feed policy of a fed-batch fermentation process for fuel ethanol production using a genetically engineered Saccharomyces yeast 1400 (pLNH33). The policy consisted of feed flow rate, feed concentration, and fermentation time. The recombinant yeast 1400 (pLNH33) can utilize glucose and xylose simultaneously to produce ethanol. However, the parent yeast utilizes glucose only. A partially selective model is used to describe the kinetic behavior of the process. In this study, this partially selective fermentation process is formulated as a general multiple-objective optimal control problem. By using an assigned membership function for each of the objectives, the general multiple-objective optimization problem can be converted into a maximizing decision problem. In order to obtain a global solution, a hybrid method of differential evolution is introduced to solve the maximizing ...
The whole computer hardware industry embraced multicores. For these machines, the extreme optimisation of sequential algorithms is no longer sufficient to squeeze the real machine power, which can be only exploited via thread-level parallelism. Decision tree algorithms exhibit natural concurrency that makes them suitable to be parallelised. This paper presents an approach for easy-yet-efficient porting of an implementation of the C4.5 algorithm on multicores. The parallel porting requires minimal changes to the original sequential code, and it is able to exploit up to 7X speedup on an Intel dual-quad core machine.
The basic structure of the LANL Environmental Restoration (ER) Site Ranking System and its use are described in this document. A related document, Instructions for Generating Inputs for the LANL ER Site Ranking System, contains detailed descriptions of the methods by which necessary inputs for the system will be generated. LANL has long recognized the need to provide a consistent basis for comparing the risks and other adverse consequences associated with the various waste problems at the Lab. The LANL ER Site Ranking System is being developed to help address this need. The specific purpose of the system is to help improve, defend, and explain prioritization decisions at the Potential Release Site (PRS) and Operable Unit (OU) level. The precise relationship of the Site Ranking System to the planning and overall budget processes is yet to be determined, as the system is still evolving. Generally speaking, the Site Ranking System will be used as a ...
Inclusion of environmental externality costs in the selection of utility resources has become a reality in New York, Massachusetts, Nevada and California. Soon several other jurisdictions are likely to join these states in using environmental externality costs in decision-making. The consideration of environmental externalities are bound to profoundly affect utility decision-making in the future. So far attention has focused largely on air emission externalities of SO_2, NO_x and CO_2. However, the recent Clean Air Act Amendments (CAAA) will reduce SO_2 emissions from utilities by about 50 percent. With such a large reduction in SO_2 loading, the question has been raised as to the need to further consider SO_2 externality costs in decision-making. This paper comments on this issue. By using generation and emission data from New York utilities, the paper shows that SO_2 emission externalities exist even after complying with ...
The IAEA attaches great importance to the dissemination of information that can assist Member States with the development, implementation, maintenance and continuous improvement of systems, programmes and activities that support the nuclear fuel cycle and nuclear applications, including management of the legacy of past practices and accidents. In this connection, the IAEA has initiated a comprehensive programme of work covering all aspects of environmental remediation: - Technical and non-technical factors, including costs, that influence environmental remediation strategies and pertinent decisionmaking; - Site characterization techniques and strategies; - Assessment of remediation technologies; - Techniques and strategies for post-remediation compliance monitoring; - Special issues such as the remediation of sites with dispersed radioactive contamination or mixed contamination by hazardous and radioactive substances. Experience in Member ...
In abnormal conditions, the operator's ability to deal with a large volume of data, and initiate the most appropriate remedial action is a fundamental concern in the design of energy control centers. Once a severe disruption has occurred in the power network, a series of tasks are required before the operator can make any decisions. Many of these functions involve computational efforts, and require a long period of processing time. The application of a wrong set of information by the operator may result in a catastrophic recovery situation. Also, as the system becomes larger, the required time for these tasks grows significantly and the operator may have very little time to analyze the contingency and issue a proper decision. These facts have led to the conclusion that a computer driven decisionmaking mechanism will help the operator perform duties with minimum flaws and ...
Although managing fisheries is complex, policymakers must makedecisions daily that affect the future of aquatic resources. To make these decisions, they often combine a mental model with lessons learned from formal models such as computer models. While such computer models are frequently interpreted as predictors of the future, they are often more valuable when used as tools for learning about fisheries and options for management. This approach, looking at computer simulations as learning laboratories, is what this study is all about since its objective is to investigate by means of a microworld if policymakers in Belgian fisheries have the policy instruments at hand to align the real fisheries world with their often completely different desired fisheries worlds. This study illustrates ba...
Using databases derived from the pattern recognition approach, the paper presents a methodology for utilizing fuzzy models to enhance the quality of decision-making using fuzzy-logic algorithms. Two multi-objective fuzzy-logic control algorithms for controlling power system static/dynamic security are presented and analyzed. The first algorithm is based on the successive inferences of fuzzy implication rules for each individual objective, and the second algorithm is an application of the method of fuzzy linear programming. The paper discusses the properties, advantages and limitations of applying fuzzy decision-making logic in the pattern-recognition approach and concludes by highlighting potential areas for further development. (author)
In the analysis of power systems security, recently a new concern related to possible malicious attacks caught much attention. Coordination among different transmission system operators (TSO) in an interconnected power system to counteract such attacks has become an important problem. This paper presents a general framework for describing the physical, cyber and decision-making aspects of the problem and their interrelations; within this framework, an analytic tool for the assessment of information impacts in handling on-line security after a malicious attack is proposed and discussed. The model is based on the socially rational multi-agent systems and the equilibrium of a fictitious play is considered to analyze the impacts of various levels of information available to the interconnected system operators on the outcomes of the decision-making process under attack. A 34-buses test system, with 3 systems interconnected by tie-lines, is presented ...
Understanding Center for Medicare and Medicaid Services (CMS) documentation and coding rules is challenging for most physicians. To accurately bill for clinical services, physicians must learn a system that may initially seem daunting, but is in fact governed by a small number of straightforward rules. The Evaluation and Management (E/M) guidelines for all service codes specify 3 components: history, examination, and medical decision-making, each with a defined set of elements or characteristics. Service coding is based on the level of care supported by the number of history and examination elements and the complexity of decision-making. This article will clarify the guidelines for outpatient clinical services and suggest a practical method of selecting appropriate E/M codes. Because physicians must often choose between billing codes 99213 and 99214 for a visit by an established patient, it will particularly focus on the minimum documentation ...
This EPRI sponsored report describes factors that influence the selection of drives in process industry. These factors include economics, safety aspects, speed control and the plant steam balance. Since the economics play a key-role in the decision, this report provides a quick way of estimating the economics of replacing steam turbines with electric motors. The tools to carry out economic analyses have been provided in the form of graphs and nomographs for quick estimation.
Although major inroads into making antiretroviral therapy available in resource-poor countries have been made, there is an urgent need for an effective vaccine administered shortly after birth, which...Full Text Available
The decision of a firm to make investments on petroleum fields depends on the expected economic performance and on the firm economics context and on country economic and regulatory constraints. Traditionally, the Net Present Value (NPV) has being used for decision criterion as a measure of profitability of investments. The other indicators are used to help investment decision, because, according to the priorities established by the firm, only one indicator may not be sufficient. On this paper we will show production strategies considering a set of economic indicators: NPV, actualized Np, Return on investment (ROI), Equivalent Present Value (EPV), Cost Benefit, and NPV/Np ratio. The use of different economic indicators permits capture different aspects from in a decision process, i.e., each indicator or a set of economic measures may result in a different perspective, that will ...
In the present work we introduce a novel multi-agent model with the aim to reproduce the dynamics of a double auction market at microscopic time scale through a faithful simulation of the matching mechanics in the limit order book. The agents follow a noise decisionmaking process where their actions are related to a stochastic variable, the market sentiment, which we define as a mixture of public and private information. The model, despite making just few basic assumptions over the trading strategies of the agents, is able to reproduce several empirical features of the high-frequency dynamics of the market microstructure not only related to the price movements but also to the deposition of the orders in the book.
This report, the eighth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1992. A special emphasis on accomplishments in nuclear power plant aging research reflects recognition that a number of plants are entering the final portion of their original 40-year operating licenses and that, in addition to current aging effects, a focus on safety considerations for license renewal becomes timely. The primary purpose of performing regulatory research is to develop and provide the Commission and its staff with the technical bases for regulatory decisions on the safe operation of licensed nuclear reactors and facilities, to find unknown or unexpected safety problems, and to develop data and related information for the purpose of revising the Commission`s rules, ...
This report, the eighth in a series of annual reports, was prepared in response to congressional inquiries concerning how nuclear regulatory research is used. It summarizes the accomplishments of the Office of Nuclear Regulatory Research during FY 1992. A special emphasis on accomplishments in nuclear power plant aging research reflects recognition that a number of plants are entering the final portion of their original 40-year operating licenses and that, in addition to current aging effects, a focus on safety considerations for license renewal becomes timely. The primary purpose of performing regulatory research is to develop and provide the Commission and its staff with the technical bases for regulatory decisions on the safe operation of licensed nuclear reactors and facilities, to find unknown or unexpected safety problems, and to develop data and related information for the purpose of revising the ...
Use of hydrogen in large scale applications is more usual than public is mentioning normally. Nevertheless reserve against hydrogen can be observed up to highest level decision-makers. Possibly a main reason can be found and eliminated by fixing: Some spectacular accidents happened in the past and found great interest. The publication of impressive accidents and the follow up of the events course was very carefully. The research in finding causalities in former decisions and follow up was not in the interest of some people or institutions. Important facts are even not noticed by insiders, but would have been very important for future decisionmakings and public acceptance of new applications. It will be demonstrated in three historical examples. Much more examples would be available and each one could help to find new applications for a saver and effective use of hydrogen in power supply. Awaking from ...
Uncertainty in computer vision can arise at various levels. It can occur in the low level in the raw sensor input, and extends all the way through intermediate and higher levels. Ideally, at any level where decisions are being made on the basis of previous processing steps, a computer vision system must have sufficient flexibility for representation of uncertainty in any of these levels. The input cue representation portion of a computer vision system should maintain the information content of the original input images, while at the same time allowing for uncertainty in the identification of attributes required by other parts of the system for decisionmaking. Processes such as edge detection, segmentation, and shape matching yield results which could bias higher level decisionmaking, unless some framework is defined for the representation of uncertainty in the context of fuzzy set ...
Not long ago primary census data became available to publicity. It opened qualitatively new perspectives not only for researchers in demography and sociology, but also for those people, who somehow face processes occurring in society. In this paper authors propose using Data Mining methods for searching hidden patterns in census data. A novel clustering-based technique is described as well. It allows determining factors which influence people behavior, in particular decision-making process (as an example, a decision whether to have a baby or not). Proposed technique is based on clustering a set of respondents, for whom a certain event have already happened (for instance, a baby was born), and discovering clusters' prototypes from a set of respondents, for whom this event hasn't occurred yet. By means of analyzing clusters' and their prototypes' characteristics it is possible to identify which factors influence the ...
This is the eighth report by the Advisory Committee on Reactor Safeguards (ACRS) that has been prepared in response to the Congressional requirement for an annual report on the Nuclear Regulatory Commission (NRC) Reactor Safety Research Program. As previously requested by the Congress, the timing of this report has been adjusted to enable the ACRS to address the proposed budget for FY 1986 and 1987 that has been submitted to the Congress by the President. Detailed comments and recommendations are provided for the research programs and budget proposed for FY 1986. Because both the budget for FY 1987 and the research programs for that period are highly uncertain at this time, comments on these are not provided. Part I is a compilation of general comments and recommendations regarding the NRC Safety Research Program budget for FY 1986. It is intended to serve as the Executive Summary. Part II is divided into five chapters, each of which represents ...
This document presents the integrated reactors concepts by a presentation of four reactors: PIUS, SIR, IRIS and CAREM. The core conception, the operating, the safety, the economical aspects and the possible users are detailed. From the performance of the classical integrated PWR, the necessity of new innovative fuels utilization, the research of a simplified design to make easier the safety and the KWh cost decrease, a new integrated reactor is presented: SCAR 600. (A.L.B.)
To be able to carry out review functions regulatory authorities must be able to make critical evaluations of proponent's safety cases. In Sweden the Swedish Radiation Safety Authority aims to have in place its own suite of performance assessment tools. This paper looks at the role and application of a regulator's models to important features of current modelling in a proponent's performance assessment. (authors)
The US Department of Energy (DOE) Mixed Waste Integrated Program (MWIP) has as one of its tasks the identification of a decision methodology and key decision criteria for the selection methodology. The aim of a multicriteria analysis is to provide an instrument for a systematic evaluation of distinct alternative projects. Determination of this methodology will clarify (1) the factors used to evaluate these alternatives, (2) the evaluator`s view of the importance of the factors, and (3) the relative value of each alternative. The selected methodology must consider the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) decision-making criteria for application to the analysis technology subsystems developed by the DOE Office of Technology Development. This report contains a compilation of several decision methodologies developed in various national laboratories, institutions, and ...
The Hanford Site in eastern Washington state currently is engaged in the largest waste cleanup in world history. In order to make informed decisions about remediation options, the public throughout the Pacific Northwest and the nation needs to understand the wastes that are present, their sources of generation, their composition, and their behavior in the environment. The fact that Hanford operations` were conducted in secret for over four decades presents a unique public information challenge to those who currently are responsible for communicating with the public.
Governments around the world will soon makedecisions on policies that could determine the fate of the ozone layer-the Earth's shield from harmful ultraviolet radiation. The Vienna Convention for the Protection of the Ozone Layer, signed on March 22, 1985, created a framework for scientific cooperation and information exchange that will form the basis for a protocol for controlling substances thought to threaten the ozone layer. As of mid-1987, 29 countries had signed the Convention, including the major producers and users of chlorofluorocarbons (CFCs), the most important of suspect chemicals.
Decision-making is strongly based on modelling in two of our water supply projects concerning artificial ground water. The model used is a 2-dimensional flow and transport model using the element method. Due to sharp variations in Finnish soils, the modelling process is based on careful and detailed evaluation of basic hydrogeological data before and during model calibration.
We have designed a local trigger board for the Daya Bay reactor neutrino experiment, which is aimed to measure the neutrino mixing angle sin22?13 with a precision down to 1% level. The local trigger board processes both the total number of coincident photomultiplier tube (PMT) hits and the PMT energy sum to make trigger decisions. With this design, a high trigger probability is achieved to meet the system requirement. The design of the local trigger board is presented.
A heuristic algorithm that employs fuzzy logic is proposed to the power system transmission expansion planning problem. The algorithm is based on the divide to conquer strategy, which is controlled by the fuzzy system. The algorithm provides high quality solutions with the use of fuzzy decisionmaking, which is based on nondeterministic criteria to guide the search. The fuzzy system provides a self-adjusting mechanism that eliminates the manual adjustment of parameters to each system being solved. (author)
In 1993 the Government of Armenia made a decision to restart Armenian Nuclear Power Plant (ANPP) which was shutdown in 1989. Shortly after that decision Armenian Nuclear Regulatory Authority (ANRA) was established. Absence of local technical support and limited international support created difficulties for new established ANAR during its activities on regulating ANPP modernization process and issuing authorization for restart. Necessity to establish TSO occurred at this stage. By initiative of ANRA a small TSO was established in 2002 with limited staff called Nuclear and Radiation Safety Centre (NRSC). This paper briefly describes the establishment, development and the current activities and problems of NRSC. (author)
In the universe there are two different kinds of uncertain phenomena: stochastic and fuzzy or vague. Both uncertain phenomena have been found in structural problems. Therefore, rational decisions concerning the design of marine structures cannot be made without resorting to the methods which can take the uncertainties into account. The fundamental concept of structural fuzzy reliability problems and the methods to give the fuzzy solution are introduced in the paper. Based on the principle of fuzzy decision-making the method to obtain the crisp solution of structural fuzzy reliability analysis is proposed by means of the Bound Search method. Illustrative numerical examples, ship bottom plates under slamming impact pressures are solved. The influence of variation of allowable tolerances in the fuzzy reliability indexes is discussed.
Background: High satisfaction rates have been reported after autologous breast reconstruction. Yet, most mastectomy patients receive implant reconstructions (ImBR). Independent and active decision makers have shown mainly to choose for autologous reconstructions, such as the Deep inferior epigastric perforator (DIEP) flap (DiepBR). To further explore the decisionmaking to opt for either ImBR or DiepBR, we investigated patient knowledge, informational resources used, effect of plastic surgeons' advice, coping style and personal independence. Methods: A total of 153 women, who were planned for DiepBR or ImBR preoperatively, completed a study-specific and standardised validated psychological questionnaire. Analyses were aimed at information-seeking behaviour, personal independence and coping...
The paper describes the latest developments in STRASSY (Strategy Assistance System), the strategy assistance system for the inspection of nuclear materials. The user can now select the fuel cycle he wishes to investigate from an initial range of 19 facilities. An inspection interface has been developed to enable the details and dates of inspections to be modified. One of the special features of the application of STRASSY in international safeguards is the taking into account of timeliness of detection; certain aspects of the time manager algorithms are presented and analysed, including the guaranteed existence of a solution. The results of a study of diversion paths in a simplified cycle consisting of our facilities are presented. Finally, the modifications necessary to enable STRASSY to be used for a posterior analysis of inspection results are discussed. (authors). 7 refs., 3 figs.
The approval (2003) and enforcement (2005) of a smoking ban in Italy have been viewed by many as an unexpectedly successful example of policy change. The present paper, by applying a processualist approach, concentrates on two policy cycles between 2000 and 2005. These had opposing outcomes: an incomplete decisional stage and an authoritative decision, enforced two years later. Through the analysis of the different phases of agenda setting, alternative specification and decisionmaking, we have compared the quality of participation of policy entrepreneurs in the two cycles, their political strategies and, in these, the relevance of issue image. The case allows us to direct the attention of scholars and practitioners to an early phase of the policy implementation process - which we have nam...
Purpose - In light of the growth of internet usage and its important role in the field of e-commerce, electronic word-of-mouth (eWOM) has been changing people's behavior and decisions. People count on other users' opinions and information; they sometimes even make offline decisions based on information acquired online. The purpose of this paper is to conceptualise eWOM activity from an input-process-output (IPO) perspective; propose a classification framework based on the identified academic literature; analyze eWOM literature in terms of quantitative development and qualitative issues that are useful to both academics and researchers; and provide directions and guidelines for future research studies in eWOM. Design/methodology/approach - The authors performed a systematic literature revie...
This discussion paper has two goals: first, to raise public awareness of food irradiation, an emerging technology in which Canada has the potential to build a new industry, mainly oriented to promising overseas markets; and second, to help build consensus among government and private sector decision makers about what has to be done to realize the domestic and export potential. The following pages discuss the potential of food irradiation; indicate how food is irradiated; outline the uses of food irradiation; examine questions of the safety of the equipment and both the safety and nutritional value of irradiated food; look at international commercial developments; assess the current and emerging domestic scene; and finally, draw some conclusions and offer suggestions for action.
In this study, the state-of-the art for estimating LERF is considered for the regulatory risk-informed decisions. The consideration is mainly focused on (1) the relationship between Level 2 PSA and LERF evaluation methodology, (2) the standard requirements in terms of modeling preparation and the acceptance criteria based on the application capability II of ASME PRA standard, and (3) some pending issues for developing and proposing a simplified LERF model. This study is preliminarily presented and will be updated for establishing detailed evaluation scheme of extended MPAS (multi-purpose probabilistic analysis of safety) model and preparing the technical basis.
There is increasing pressure to operate laboratory facilities in environmentally and financially sustainable ways. A key factor in achieving this goal is careful consideration of how energy is used by the buildings' ventilation system, both for conditioning air supplied to the laboratories and the energy used moving air through the building. Traditionally, laboratory energy use is treated as an engineering concern within the scope of the building's overall design and operation. However, this approach limits the involvement of key stakeholders in many important decisions and can lead to unexpected safety concerns for the laboratory's users. We believe that a broad view of the parties affected by a laboratory building's operations is necessary to avoid having the various stakeholders working...
This Health and Safety (HSE) document offers technical information on the design of foundations for supports in offshore installations, and relates particularly to the North Sea. It is based largely on guidance offered earlier in Section 20 of the Fourth Edition of the Health and Safety Executive's 'Offshore Installations; Guidance on Design, Construction and Certification', which was withdrawn in 1998. The document contains a general section on foundations and the rest of the document comprises sections on: (a) piled foundations (planning, problems, pile make-up, steel stresses, design of pile foundations, axial pile capacity, factors of safety for piled foundations, load-deflection of piles, and piles for tethered buoyant structures); (b) foundations for gravity structures (foundation types, loads and reactions during installation, operating loads and reactions, foundation ...
Section 7 of the Atomic Energy Act (AtG), section 4 of the Federal Emission Control Act (BImSchG), the Nuclear Installations Licensing Ordinance (AtVfV), and the Ninth Ordinance on the Implementation of the BImSchG (Principles of the licensing procedure) require participation of the public in the procedure before administrative provisions or decisions are issued. The book presents the legally prescribed steps at which participation of the public is mandatory, for the simple case (only one license on the agenda), and for the multi-stage licensing procedure: preliminary negotiations / filling of applications for a license and filing of documents / public announcement of projects / access to files / objections / preclusion of delayed objections / public hearing and other expert discussions / termination of procedure, decision-making by the authorities / decisions on subdivision of procedure into defined stages / modification ...
Until recent years, those involved in the design, operation and regulation of nuclear power systems devoted more resources to forward movement than to the back end of the fuel cycle. Now, though, concerted thought and international cooperation have been devoted to the question of nuclear waste management. The expert consensus is that sufficient knowledge exists to make e.g. disposal decisions with an acceptable level of confidence. In the first phases of research, decision processes were adapted to the tasks at hand. However, at some point in each nuclearized country, there came a time when waste management implied finding repository sites. At that time management abruptly entered the social sphere - where unfortunate experience has shown time and time again that classical decision processes are not adapted to facilitating societal acceptance of management solutions. This paper recounts the various ...
The unique time scales associated with nuclear waste management require active work to preserve the knowledge associated with programs that can often span long time frames. For example, repository programs are designed and developed for the safe containment of radionuclides with half-lives on the order of 24,000 years (for Pu-239). Performance assessment studies are required to show, by predictive modeling, that these repositories can safely contain the waste for tens of thousands of years, with one million years a reality in the debate. Development of successful repository programs can span several decades. Once operational, a repository is expected to function until closure for a period of 30 to 40 years. Yet, the decision makers at all levels in such a repository program exert influence and authority over much shorter periods of time (e.g., four years for executive appointments). A discontinuous decision-making process and the associated ...
In the paper, a fuzzy decision-making methodology is presented to decide the generation schedule of long-term hydrothermal problems with explicit recognition of statistical uncertainties in system production cost data, NO{sub x} emission data, system load demand and hydro reservoir water inflows. In deciding the optimal operation, three objectives operating cost, NO{sub x} emission and unsatisfied load demand over the whole of the planning period are simultaneously minimised. Specific technique is put forth to convert the stochastic models into their deterministic equivalents. The weighted minimax method is used to simulate the tradeoff relation between the conflicting objectives in the non-inferior domain. The fuzzy set theory is exploited to choose the best operating point over the tradeoff curve. An efficient decomposition technique is applied to reduce the complexity of the problem. In each subproblem, thermal generations are obtained by using simplified method ...
Inco Ltd., a primary producer of nickel and an important producer of copper, cobalt, precious metals and sulphur products, initiated a project in 1997 to conduct eco-profiles of its worldwide metal production in an effort to improve its internal processing, marketing and environmental management. The study made it possible to recognize some internal and external benefits including the opportunity to gain operating efficiencies and improved process/product design, the development of better environmental performance indicators to guide decisionmaking, and the availability of comprehensive product related environmental data to meet the informational needs of customers, designers, engineers and governments. This paper described the life cycle assessment (LCA) process used by Inco to conduct the study. A life cycle inventory (LCI) was used to quantitatively calculate resource requirements and environmental burdens associated with a product system ...
This study develops a framework for analysis and assessment of the cost of ownership and use of major cooking appliances. This involved an assessment of the monetary cost as well as the cost of human resources required to maintain and operate cooking systems. The goal was to provide information useful in making purchase decisions within a framework that can be used to organize information about cost beyond the initial purchase price. Five cooktops - conventional electric oil, induction, solid element with thermostatic control, solid element with thermal limiter, and gas - and a microwave oven were used to develop a decision-making matrix. Results were used to assign weights in the matrix used to develop a 10-point scale that represented the total cost of owning and using a cooking system in food preparation. Based on the matrix, the microwave oven received the highest score followed by gas, conventional electric coil, solid ...
The UK fully supports the objective of the Joint Convention on the Safety of Spent Fuel Management and on the Safety of Radioactive Waste Management to achieve and maintain a high level of safety worldwide in spent fuel and radioactive waste management, through the enhancement of national measures and international co-operation, including where appropriate, safety-related co-operation. The UK's Health and Safety Executive, through its Nuclear Safety Directorate (NSD), has been committed to the Convention since the initial negotiations to set up the Convention and provided the president of the first review meeting in 2003. It would be wrong of any nation to believe that they have all the best solutions to managing spent fuel and radioactive waste. The process of compiling reports for the Convention review meetings provides a structured process through which every ...
The properties of the mixing layer in dynamic systems were studied by the example of a mathematical model of the cubic image type. Its role in the generation of information and the evolution of its significance was shown. At the moment of generation, information is of zero significance, and this significance then increases. A criterion of efficiency was proposed, and the optimum moment of making a decision in creative work was determined. It was shown that the increase in the variability of the parameters of a living system upon entry into the mixing layer and its decrease upon exit can serve as objective indicators of the transition of the system from one dynamic regime (attractor) to another. PMID:12723364
A conceptual framework is proposed within which the notion of risk as normally used in risk assessment (RA) could be enlarged in line with the real substance of social issues of technology policy, to help avoid RA's threatened irrelevance to social decisionmaking. It is argued that the frequent organizational incoherence and thus the unviability of modern technology arises from 'social alienation' between the innovation-commitment phase and the implementation of the technology in society. The roles of technical elites and of particular concepts of technology in this alienation are emphasized. One of the case studies deals with 'Nuclear power - myths of scientific and organizational realism' and discusses the UK nuclear 'programme' and the Three Mile Island accident. (author).
Innate immune responses are regulated by microorganisms and cell death, as well as by a third class of stress signal from the nervous and endocrine systems. The innate immune system also feeds back, through the production of cytokines, to regulate the function of the central nervous system (CNS), and this has effects on behaviour. These signals provide an extrinsic regulatory circuit that links physiological, social and environmental conditions, as perceived by the CNS, with transcriptional 'decision-making' in leukocytes. CNS-mediated regulation of innate immune responses optimizes total organism fitness and provides new opportunities for therapeutic control of chronic infectious, inflammatory and neuropsychiatric diseases.
There is a growing interest on dynamic and broader concepts of deprivation such as vulnerability, which takes in to account the destitution of individuals from future shocks. We use the framework of decisionmaking under uncertainty to arrive at a new measure of vulnerability to poverty. We highlight the importance of current standard of living to better capture the notion of vulnerability. In conceptualizing the new class of measures of vulnerability, we thus move beyond the standard expected poverty measures that is commonly found in the literature. We also axiomatically characterize the new class of measure and discuss some of its properties.
This paper presents a framework for creating a common spatial canvass that can bring together considerations of resource availability, infrastructure reliability, and development costs while strategizing renewable energy investment. We describe the underlying models and methodologies that annotate an investment plan for potential sites over a time-period with costs and constraints which may be imposed on distance from infrastructure, system impact on infrastructure, and policy incentives. The framework is intended as an enabler for visualization, optimization and decisionmaking across diverse dimensions while searching for lucrative investment-plans.
Ascochyta blight causes significant yield loss in pulse crops worldwide. Integrated disease management is essential to take advantage of cultivars with partial resistance to this disease. The most effective practices, established by decades of research, use a combination of disease-free seed, destruction or avoidance of inoculum sources, manipulation of sowing dates, seed and foliar fungicides, and cultivars with improved resistance. An understanding of the pathosystems and the inter-relationship between host, pathogen and the environment is essential to be able to make correct decisions for disease control without compromising the agronomic or economic ideal. For individual pathosystems, some components of the integrated management principles may need to be given greater consideration tha...
...forest products export revenue: call for new strategies by Roda Jean-Marc & Ismariah Ahmad & Rohana Abd Rahman & Lim Hin Fui &...pattern: the cards have changed by Roda Jean-Marc & Rohana Abd Rahman & Ismariah Ahmad & Lim Hin Fui & Mohd Parid Mamat [...] 2010, Volume 2010, Issue 07 15 Decision-making and sampling size effect by Ismariah Ahmad & Rohana Abd Rahman & Roda Jean-Marc & Lim Hin ... by Roda Jean-Marc & Ahmad Fauzi Puasa & Lim Hin Fui & Rohana Abd Rahman & Ismariah Ahmad [Downloadable!]...
This paper presents the results of a model for the impact of potential contamination produced by radionuclide leaking due to long-term physical, chemical and hydrogeological processes occurring in a LILW repository and in the natural environment. The analysis contains a deterministic and also a probabilistic approach for uncertainty assessment. The input function, i.e., the source term was evaluated by using AMBER code and the entire analysis was accomplished by using GOLDSIM, a powerful tool to support probabilistic simulation in management and decision-making in engineering and science. The results obtained were compared to previous simulations and uncertainty analyses (FEHM). (authors)
This paper is aimed to present a fuzzy decisionmaking approach to deal with the performance measurement in supply chain systems. In the manufacturing environment, performance measurement is based on different quantitative and qualitative factors. Some of these factors may have a larger effect on the performance measure than others. Units of measure of the quantitative factors are different such as time, money, percentage, ratio, and counts. Thus, this paper presents a performance measurement approach based on fuzzy set theory and the pair-wise comparison of Analytical Hierarchy Process (AHP), which ensures the consistency of the designer's assignments of importance of one factor over another to find the weight of each of the manufacturing activity in the departmental organization. In the ...
A 1976 decision of the US Supreme Court made it clear that the Federal Energy Regulatory Commission (then the Federal Power Commission) has a responsibility to consider and determine allegations that proposed wholesale electric rates create a price squeeze against customers who compete with the wholesaler in making retail electric sales. This article reviews how the commission has approached the matter of discharging its newly recognized responsibility since that time, and describes its current position regarding the several issues and questions that price squeeze allegations raise. 35 references.
Microcomputers are beginning to be used for energy analysis in many developing countries, and have the potential for making a significant contribution to the resolution of difficult analytical and data problems, and to improving communications between analyst and decision maker. Successful introduction of a microcomputer based on analytical capability, however, requires attention to several important factors in order to avoid the mistakes of the earlier mainframe computer era. This paper reviews the key issues of matching models to staff capabilities, of training, and of the operating environment, based on the author's first-hand experience with microcomputer projects in Uruguay, Haiti and Sri Lanka. 3 figures, 3 tables.
Decisionmaking about possible investment options for energy supply technology is usually based on economic criteria reflecting primarily the unit cost of energy and the return on capital invested. This study attempts to reverse the process. The chosen starting point is a UK investment programme geared towards reliance on conservation, renewable energy systems and the more efficient use of our remaining fossil fuels (through combined heat and power and district heating systems). The number and type of jobs likely to be created is then estimated and compared with the jobs likely to be created by the currently proposed nuclear power programme. (author).
The use of reversible pump/turbine sets in pumped storage has created a requirement for rapid reversibility. Softstart technology, based on static frequency converters (SFC) has evolved to such an extent that it is now the best choice for serving this purpose, both from a technical and from an economic point of view. The objective of our paper is to give the owners of pumped storage plants and those persons responsible for the selection, the operation or the maintenance of the electrical equipment the necessary insight into the SFC functions, features and all other application related aspects, to facilitate their decisionmaking process. Case studies are included.
This paper considers location?allocation problem in the real uncertain world and develops a possibilistic non-linear programming model to deal with this problem. Fuzzy decisionmaking in fuzzy environment concept is used to determine possibility distribution of location and allocation variables. To solve this model, a novel approach based on genetic algorithm structure is developed. As the proposed model includes both deterministic (location) and uncertain (allocation) parameters, the developed solution algorithm uses a hybrid chromosome structure. Also, to cover continuous nature of the problem and prevent GA from early convergence, a new crossover operator is introduced. Finally, performance of the developed algorithm is evaluated by an example.
Ensuring security of e-government applications and infrastructures is crucial to maintain trust among stakeholders to store, process and exchange information over the e-government systems. Due to dynamic and continuous threats on e-government information security, policy makers need to perform evaluation on existing information security strategy as to deliver trusted e-government services. This paper presents an information security evaluation framework based on new fuzzy multi criteria decisionmaking (MCDM) to help policy makers conduct comprehensive assessment of e-government security strategy.
The purpose of this study is to determine whether there are differences among visitors to a destination based on their golfing frequency in the previous year. By constructing a framework for understanding the golf traveller, golf and tourism industry representatives can better understand the contribution that golfers make to a destination based on factors such as satisfaction, perceived value received from the golfing experience, trip length, expenditures, travel decisions, and motivations. The results indicate that there are significant differences between golfers based on golfing frequency. Dedicated golfers are very different from infrequent and moderate golfers on three of the four variables used to profile these visitors. Findings from this research may provide golf and tourism market...
To evaluate safety of horizontal steam generator used in passive safety system, it is needed to make clear flooding characteristics in U bend pipe. In this study, two-phase flow experiment in a horizontal U bend pipe was carried out to make clear the influence of the length of horizontal pipe and the radius of U bend. Flooding in the U bend pipe was observed in the condition of lower gas or liquid volumetric flux than that in the horizontal pipe or the vertical pipe. Flooding and carry-up in the U bend pipe is hardly change with increasing the length between the water inlet and the U bend, but greatly related with the length from the water inlet to the lower tank and the shape of the U bend inlet. (author).
This practical guide for the agribusiness manager (the farmer, rancher, and other agribusiness people who work with agricultural commodities, supplies, and services) gives a basic understanding of modern management practices. It provides guidelines that can help them make practical business decisions. Chapter 1 is an introduction that highlights farm management efficiency, decisionmaking, and goals and objectives. The following 11 chapters discuss recordkeeping (importance and purposes of keeping records, types of systems, record book components), financial analysis (cash flow, net worth, income statements and their ratios; whole farm and enterprise analysis; relationships of various analyses), budget analysis (introduction to types and uses of budgets, how to use and analyze a partial budget, enterprise budget and whole farm budget, production principles, cost components), cash flow analysis ...
The main objective of this paper is to identify conditions which affect public concern (either increase or decrease) and political acceptance for developing and implementing programmes for geologic disposal of long-lived radioactive waste. It also looks how citizens and relevant actors can be associated in the decisionmaking process in such a way that their input is enriching the outcome towards a more socially robust and sustainable solution. Finally, it aims at learning from the interaction how to optimise risk management addressing needs and expectations of the public and of other relevant stakeholders. In order to meet these objectives, factors of relevance for societal acceptance conditions are identified, described and analysed. Subsequently these factors are looked for in the real world of nuclear waste management through cases in several countries. The analysis is conducted for six stages of a repository programme and implementation ...
Prepared to make housing project managers, maintenance engineering staff, and designers and architects of HUD - assisted and HUD - insured housing projects and mobile home parks aware of their responsibilities under the Natural Gas Pipeline Safety Act, this handbook provides technical guidance for the reduction of gas leaks and the handling of gas leak incidents in residential areas. The hazards of natural gas, concern over gas safety in residential areas, applicable codes and standards, and sources of information and help are reviewed, along with maintenance and engineering considerations relating to gas pipe failures, the detection of gas leaks, appliance servicing, and pipe installation, repair, and replacement. Housing management considerations are also examined, with attention to recordkeeping and reporting, emergency contingency planning, tenant education, staff qualifications and training, and the development and use ...
The Belgian Tihange 2 nuclear power plant went into commercial operation in 1983 producing a thermal power of 2785 MW. Since the commissioning of the plant the steam generators U-tubes have been affected by primary stress corrosion cracking. In order to avoid further degradation of the performance and an increase in repair costs, Electrabel, the owner of the plant, decided in 1997 to replace the 3 steam generators. This decision was supported by the feasibility study performed by Tractebel Energy Engineering which demonstrated that an increase of 10% of the initial power together with a fuel cycle length of 18 months was achieved. Tractebel Energy Engineering was entrusted by Electrabel as the owner's engineer to manage the project. This paper presents the role of Tractebel Energy Engineering in this project and the safety analysis program necessary to justify the new operation point and the fuel cycle extension to 18 months re-analysis of FSAR ...
Due to current social and economical framework, in last years many nuclear power plant owners started a program for the Long Term Operation (LTO)/PLIM (Plant Life Management) of their older nuclear facilities. PLIM/PLEX has already been implemented in many countries (USA, Russia, etc.). This process has many nuclear safety implications, other than strategic and political ones. The need for tailoring the available safety assessment tools to such applications has become urgent in recent years and triggered many research actions. In particular, a PLIM framework requires both a detailed review of the features of the main safety programs (Maintenance, ISI, Surveillance) and a complete integration of these programs into the general management system of the plant. New external factors, such as: large use of subcontractors, need for efficient management of spare parts, request for heavy plant refurbishment programs demand for ...
To make a quantitative comparison of risks between the SNR 300 and a modern PWR (Biblis B), the consequences of an accident or the extent of damage of a release of radionuclides to the environment due to an accident are estimated by computer programs for accident consequence models. The accident analysis includes an analysis of events for Bethe-Tait accidents with failure of the outer containment. The FGSB release rates are compared with those of the Society for Reactor Safety (GRS). (HP).
An Ottawa-based company, ECS-Power Systems Inc., has successfully completed a series of tests on an innovative device called a hydrodynamic port (HDP), which makes it possible to automatically initiate and maintain emergency cooling of a nuclear reactor core by natural processes, without relying in any way on human intervention, instrumentation, electric power, valves or moving parts of any kind.
This report describes a high explosives test facility that makes efficient use of equipment and combines utility, convenience, and safety in a modest amount of space. It is a dedicated facility for exploratory development efforts that previously were conducted in a single room having very limited capabilities. Two explosives testing areas are now available and several projects are supported concurrently.
The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970's, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on the waste form. The Department of Energy, recognizing that ...
The Department of Energy currently has over 100 million liters of high-level radioactive waste in storage at the Savannah River Site (SRS). In the late 1970`s, the Department of Energy recognized that there were significant safety and cost advantages associated with immobilizing the high-level waste in a stable solid form. Several alternative waste forms were evaluated in terms of product quality and reliability of fabrication. This evaluation led to a decision to build the Defense Waste Processing Facility (DWPF) at SRS to convert the easily dispersed liquid waste to borosilicate glass. In accordance with the NEPA (National Environmental Policy Act) process, an Environmental Impact Statement was prepared for the facility, as well as an Environmental Assessment of the alternative waste forms, and issuance of a Record of Decision (in December, 1982) on the waste form. The Department of Energy, recognizing that start-up of ...
China operates 10 nuclear power reactors and has 5 more under construction. A large extension of nuclear power is expected by 2020. Nuclear generated electricity accounts for 2% of the total electric power generation. The Chinese policy is to have spent fuel reprocessed in China. So, final disposal include vitrified waste and some CANDU spent fuel for direct disposal. There is a legal framework in place in China to manage HLW. The China Atomic Energy Authority (CAEA) has the responsibility for setting policy on HLW disposal and implementing the disposal programme, while the National Nuclear Safety Administration (NNSA) and the State Environment Protection Agency (SEPA) are the regulatory bodies, which are responsible for licensing and reviewing of environment impact assessment report. The China National Nuclear Corporation (CNNC) is considered to be the actual implementer, conducting the major activities for HLW management. In the 1980's, China started generic ...
The Savannah River Site (SRS) is a 310-square-mile United States Department of Energy nuclear facility located along the Savannah River (SRS) near Aiken, South Carolina. Nuclear weapons material production began in the early 1950s, utilizing five production reactors. In the early 1990s all SRS production reactor operations were terminated. The first reactor closure end state declaration was recently institutionalized in a Comprehensive Environmental Response and Compensation and Liability Act (CERCLA) Early Action Record of Decision. The decision for the final closure of the 318,000 square foot 105-P Reactor was determined to be in situ decommissioning (ISD). ISD is an acceptable and cost effective alternative to off-site disposal for the reactor building, which will allow for consolidation of remedial action wastes generated from other cleanup activities within the P Area. ISD is considered protective by the regulators, U. S. Environmental ...
Construction and commissioning period of NPP are reduced world over drastically by stringent schedule for financial and economic reasons. For meeting the schedule, commissioning of components and systems are started immediate after installation, while construction activities are continued in parallel at the same place. Parallel activities' and 'Time Constraint' have brought new challenges to 'Management of Fire and Industrial Safely' during commissioning. An innovative approach was used during such phase of commissioning of TAPP-3 and 4. This paper outlines challenges encountered during this phase and special approach and measures used to meet those challenges. This paper also outlines problems encountered during implementation of these measures and subsequent change in approach to ensure smooth and safe execution of activities. Primarily, challenges were conflicting requirements by various agencies to carryout commissioning in parallel with construction activities concurrently. Main ...
This paper presents a new approach for solving multistage decision problems in power system operation by using a new fuzzy dynamic programming technique. To investigate its validity, the hydrothermal scheduling problem is used as an example problem. Within this problem, uncertainty elements exist such as load demand and natural hydraulic inflows to reservoirs exist which can be expressed by fuzzy numbers. Two new fuzzy decisionmaking techniques for selecting the optimal operating states at each stage are introduced. Further, the hydrothermal scheduling solution obtained had an operating band defined by upper and lower bounds. To further enhance the information that this operating band provides, a midpoint operation technique that applies both forward and backward fuzzy DP is also introduced. This allows the system operator to consider current operating conditions to determine a suitable stage by stage operation policy ...
The paper summarizes the results obtained in two interview studies conducted in the communities of Storuman and Malaa in northern Sweden, 1995 and 1997. It highlights the similarities and differences with respect to the public participation and decision processes which preceded the respective referenda in the two communities. The presentation includes the arguments used by proponents and opponents, the changes over time, as well as the time frame and the information involved in the processes. It is concluded e.g. that local cultures, life-styles, knowledge of similar events, and the time for and management of the participation process are important and salient factors in the resulting social dynamics. Factors of possibly more fundamental importance were also discerned, however, including overall attitude to and valuation of nuclear power, perceptions of development, solidarity, power and power distribution in relation to current as well as future situations. It is ...
A sequential problem in decentralized detection is considered. Two observers can make repeated noisy observations of a binary hypothesis on the state of the environment. At any time, observer 1 can stop and send a final binary message to observer 2 or it may continue to take more measurements. Every time observer 1 postpones its final message to observer 2, it incurs a penalty. Observer 2's operation under two different scenarios is explored. In the first scenario, observer 2 waits to receive the final message from observer 1 and then starts taking measurements of its own. It is then faced with a stopping problem on whether to stop and declare a decision on the hypothesis or to continue taking measurements. In the second scenario, observer 2 starts taking measurements from the beginning. It is then faced with a different stopping problem. At any time, observer 2 can decide whether to stop and declare a decision on the ...
Purpose The laparoscopic surgical approach to unilateral intra-abdominal testis has replaced the open approach at several large centers. There is considerable literature on experience with unilateral intra-abdominal testes but little on the management of bilateral intra-abdominal testes. We assessed the feasibility and safety of performing single setting bilateral laparoscopic orchiopexy in boys with bilateral intra-abdominal testes. Materials and Methods A single surgeon experience was reviewed. The surgical technique was similar in all cases and on each side, including infra-umbilical access, diagnostic evaluation, peritoneal mobilization lateral to the spermatic vessels and inferior to the vas deferens, gubernacular transection, and a decision for or against a Fowler-Stephens procedure ...
Australia?s nationally consistent framework for gene technology regulation is underpinned by the Gene Technology Act 2000, administered by an independent decision-maker, the Gene Technology Regulator. The object of the Act is ?to protect the health and safety of people, and to protect the environment, by identifying risks posed by or as a result of gene technology, and by managing those risks through regulating certain dealings with genetically modified organisms?. Marketing and trade impacts are outside the scope of assessments required by the Act. Since 2001, seven licences have been issued for the commercial cultivation of genetically modified (GM) cotton with insect resistance and/or herbicide tolerance. Licences have also been issued for 32 GM cotton field trials with a broader range ...
Experiences in hazardous materials transportation show that purely strategic or planning approaches have considerable shortcomings and that real-time management must be addressed. The commercialization of advanced location and communications technology provides the basis for real-time guidance. Considering the possibilities this new technology offers, a real-time routing model is proposed. It is based on the premises that a human dispatcher must assess the impacts of sudden events on safety and transportation costs and evaluate safe and cost-effective routing alternatives. Due to high uncertainty and time constraints in this real-time environment, risks and transportation costs are expressed as preferences on an ordinal scale. The model has been integrated into a decision support system and assessed in an experimental setting. This ordinal preference model turned out to be superior to a utility approach due to its robustness in risk assessment ...
Taking into consideration India's limited reserves of natural and vast reserves of thorium, the fast reactor route holds a great promise for India's energy supply in future. The fast reactor fueled with "2"3"9Pu/"2"3"8U (unused or depleted) produces (breeds) more fissionable fuel material "2"3"9Pu than it consumes. Calculations show that a fast breeder reactor (FBR) increases energy potential of natural uranium by about 60 times. As the fast reactor can also convert "2"3"2Th into "2"3"3U which is a fissionable material, it can make India's thorium reserves a source of almost inexhaustible energy supply for a long time to come. Significant advantage of FBR plants cooled by sodium and their world-wide operating experience are reviewed. There are two main safety issues of FBR, one nuclear and the other non-nuclear. The nuclear issue concerns core disruptive accident and the non-nuclear one concerns the high chemical energy potential of sodium. ...
BackgroundIn patients with Stage 5 Chronic Kidney Disease who require renal replacement therapy a major decision concerns modality choice. However, many patients defer the decision...Full Text Available
The automotive industry desires to optimize safety and lightweight construction for the production of cars and trucks. The resulting task for steel suppliers is to make steel grades available that can fulfil these requirements. Different projects have shown optimistic outlooks for optimization of safety and reduction of the weight of automobile bodies by using different high strength and ultra high strength steels. In the last group the dual phase steels play the lead. In recent years different steel grades have been developed and optimized for these applications. On one hand developing the mechanical properties as well as joining and forming of dual phase steels is one of the first steps. On the other hand different coated surfaces for various applications of dual phase steels is another step. Starting with characteristic production conditions for cold rolled hot dip galvanised dual phase steels, the mechanical properties ...
In this work, we aim to gain a better understanding of the volatility smile observed in options markets through microsimulation (MS). We adopt two types of active traders in our MS model: speculators and arbitrageurs, and call and put options on one underlying asset. Speculators makedecisions based on their expectations of the asset price at the option expiration time. Arbitrageurs trade at different arbitrage opportunities such as violation of put-call parity. Difference in liquidity among options is also included. Notwithstanding its simplicity, our model can generate implied volatility (IV) curves similar to empirical observations. Our results suggest that the volatility smile is related to the competing effect of heterogeneous trading behavior and the impact of differential liquidity.
The application of multi-objective genetic algorithms for green building design in two phases were presented in order to better help designers in the decision-making process. The purpose is to minimize two conflicting criteria: the life-cycle cost and the life-cycle environmental impact. Environmental impact criteria examined include energy and non-energy natural resources, global warming, and acidification. Variables focus on building envelope-related parameters. The application of multi-objective genetic algorithms is divided into two phases. The first phase intends to help designers in understanding the trade-off relationship between the two conflicting criteria. The second phase intends to refine the performance region that is of the designer's interest. The results after the two-phase application of the multi objective genetic algorithm were then presented. 13 refs., 4 tabs., 3 figs.
In 1996 the actions of EDF in the domain of environment have recorded FF 4 billions (FF 3.5 billion in 1995), representing about 2% of the EDF's turnover. The EDF keeps on its efforts for reducing the impact of its activities upon environment. Several applications of an environment protective electricity generation are promoted by the company. The company brings services and technical solutions to its clients which meet their energy needs and conserving at the same time the life conditions. Furthermore, EDF participates in the activity of numerous national and international organisms, intervening in the environmental questions, in decisionmaking, participating in studies and actions and following continually the direction of a durable economic and social development. The report is structured in three chapters: 1. an industrial responsibility; 2. services and techniques for environment; 3. action towards a durable development.
This report summarizes a public workshop that was held on April 27, 1999, in Rockville, Maryland. The workshop was conducted as part of the US Nuclear Regulatory Commission's (NRC) efforts to further develop its understanding of the risks associated with low power and shutdown operations at US nuclear power plants. A sufficient understanding of such risks is required to support decision-making for risk-informed regulation, in particular Regulatory Guide 1.174, and the development of a consensus standard. During the workshop the NRC staff discussed and requested feedback from the public (including representatives of the nuclear industry, state governments, consultants, private industry, and the media) on the risk associated with low-power and shutdown operations.
The Low Power and Shutdown (LPSD) PRA (Probabilistic Risk Assessment) Standard (ANS-58.22) is currently being drafted by a Writing Group under the auspices of the Risk Informed Standards Committee of the American Nuclear Society (ANS). The Writing Group includes representatives from nuclear utilities, US Nuclear Regulatory Commission (NRC), national laboratories, universities, and consultants with substantial experience producing LPSD PRAs. This draft standard is scheduled to be released for public comment in the second quarter of 2004, with publication by the end of 2004. The LPSD PRA Standard is based on a mature technology that shares many requirements with full power PRAs. It will provide specific methods and criteria whereby PRAs of appropriate quality and scope can be used in the conduct of plant decision-making and other activities, including addressing NRC requirements. This paper presents the current status of this standard.
As organizations merge or collaborate closely, an important question is how their existing software assets should be handled. If these previously separate organizations are in the same business domain - they might even have been competitors - it is likely that they have developed similar software systems. To rationalize, these existing software assets should be integrated, in the sense that similar features should be implemented only once. The integration can be achieved in different ways. Success of it involves properly managing challenges such as making as well founded decisions as early as possible, maintaining commitment within the organization, managing the complexities of distributed teams, and synchronizing the integration efforts with concurrent evolution of the existing systems.Th...
This paper describes the results of a French-Lebanese scientific cooperation, between 2001 and 2005, about 'Rational use of energy in the residential buildings in Lebanon and adaptation of an energy certification procedure'. The aim of this project is to promote the energy efficiency in the existing residential buildings in Lebanon, using an energy certification procedure, and to evaluate the energy certification foresight with prospective methods. The paper first describes an energy investigation in Lebanese residential buildings, and the energy certification procedure. It presents the foresight methodology implemented to identify the key variables and the actors. Finally, the paper exposes the morphological method which allows to elaborate three scenarios of energy performance certification. These scenarios are presented in order to provide a decisionmaking for the actors of the Lebanese energy policy.
In August 1995, the US Nuclear Regulatory Commission (NRC) issued a policy statement proposing improved regulatory decisionmaking by increasing the use of probabilistic risk assessment (PRA) in all regulatory matters to the extent supported by the state-of-the-art in PRA methods and data. A key aspect in using PRA in risk-informed regulatory activities is establishing the appropriate scope and attributes of the PRA. In this regard, the American Society of Mechanical Engineers (ASME) decided to develop a consensus PRA standard. The objective is to develop a PRA standard such that the technical quality of nuclear plant PRAs will be sufficient to support risk-informed regulatory applications. The authors present example recommendations for the systems analysis element of a PRA for incorporation into the ASME PRA standard.
Personal health information management (PHIM) refers to activities that support consumers' access, integration, organization, and use of their personal health information. We investigated PHIM in the health consumer population using a focus group and participatory design. In collaboration with health consumers, we identified PHIM activities and explored the design of new supportive technology. Our findings describe prominent PHIM activities such as monitoring and assessing health, as well as health-related decisionmaking, planning, and action. We describe design principles our participants used during the participatory design of a PHIM tool. These include individual control, sharing, integration, security and flexibility. These findings provide new insights into emerging ideas in consumer health informatics research and technology design. Understanding health consumers' PHIM needs is an important step in creating technology to support these ...
Objective: To describe the meaning of the theme of empowerment from research on health promotion in nursing from the perspective of nurses participating in the study. Methods: Manual data analysis and QSR NUD*IST Vivo were used to analyse the data generated by individual and focus group interviews and the critical incident technique with 32 qualified nurses working in an acute hospital setting in the UK. Results: The participants identified a number of issues related to the theme of empowerment. These included the nurse as patient informer, psychological supporter and rapport builder and the concepts of informed choice/decisionmaking, gatekeeping, coping, patient assertiveness, self-esteem and confidence. Conclusion: Empowerment is a complex, multi-dimensional, contested concept which can...
Accessible summary - -Children with a Nonverbal Learning Disability (NLD) resulting from shunted hydrocephalus and spina bifida face many difficulties not experienced by those with a language learning disability. - -As they grow older and more autonomy is expected, friendships became harder to sustain and daily life can be full of fear if the nonverbal learning disability is not identified and managed. - -This paper explains the theorised cause of nonverbal learning disability - damage to right hemisphere white matter or myelin. - -Damage is believed to cause problems with planning, organisation, time management, problem-solving, decision-making and friendships, and the mismatch with articulate speech and a good vocabulary causes a functional profile that is difficult for educationists or ...
The use of meta-analysis has become increasingly useful for clinical and policy decisionmaking. A recent development in meta-analysis, multiple treatment comparison (MTC) meta-analysis, provides inferences on the comparative effectiveness of interventions that may have never been directly evaluated in clinical trials. This new approach may be confusing for clinicians and methodologists and raises specific challenges relevant to certain areas of medicine. This article addresses the methodological concepts of MTC meta-analysis, including issues of heterogeneity, choice of model, and adequacy of sample sizes. We address domain-specific challenges relevant to disciplines of medicine, including baseline risks of patient populations. We conclude that MTC meta-analysis is a useful tool in the context of comparative effectiveness and requires further study, as its utility and transparency will likely predict its uptake by the research and clinical ...
Background:- Children with oppositional defiant disorder/conduct disorder (ODD/CD) have shown deficits in -cool- abstract-cognitive, and -hot- reward-related executive function (EF) tasks. However, it is currently unclear to what extent ODD/CD is associated with neuropsychological deficits, independently of attention deficit hyperactivity disorder (ADHD). Methods:- Fifty-nine adolescents with a history of early-onset oppositional problems, 28 with pure ODD/CD symptoms and 31 with ADHD with or without ODD/CD, and 34 healthy controls were administered a task battery measuring motor response inhibition, sustained attention, cognitive flexibility and reward-related decision-making. Findings were analysed using dimensional and group analyses. Results:- In group analyses both groups with and wit...
Szmidt and Kacprzyk (Lecture Notes in Artificial Intelligence 3070:388?393, 2004a) introduced a similarity measure, which takes into account not only a pure distance between intuitionistic fuzzy sets but also examines if the compared values are more similar or more dissimilar to each other. By analyzing this similarity measure, we find it somewhat inconvenient in some cases, and thus we develop a new similarity measure between intuitionistic fuzzy sets. Then we apply the developed similarity measure for consensus analysis in group decisionmaking based on intuitionistic fuzzy preference relations, and finally further extend it to the interval-valued intuitionistic fuzzy set theory.
The current Risk-informed Regulation (RIR) framework employs both a Level 1 Core Damage Frequency (CDF) and a Level 2 Large Early Release Frequency (LERF) as two surrogate measures for the plant risk. For their use in making regulatory decisions for the plant risk, it has been required to maintain an appropriate level of quality for the plant risk models. The first step for this purpose is to evaluate the quality of the PSA model in a qualitative or quantitative manner. Recently, a similar type of quality evaluation has been made for the KSNP Level 1 PSA model based on an ASME PRA Standard for the RIR application, but not for the corresponding LERF model. The main objective of this paper is to provide the ASME PRA Standard-based evaluation result for the existing KSNP Level 2 LERF model and the insights obtained from the evaluation process.
The current Risk-informed Regulation (RIR) framework employs both a Level 1 Core Damage Frequency (CDF) and a Level 2 Large Early Release Frequency (LERF) as two surrogate measures for the plant risk. For their use in making regulatory decisions for the plant risk, it has been required to maintain an appropriate level of quality for the plant risk models. The first step for this purpose is to evaluate the quality of the PSA model in a qualitative or quantitative manner. Recently, a similar type of quality evaluation has been made for the KSNP Level 1 PSA model based on an ASME PRA Standard for the RIR application, but not for the corresponding LERF model. The main objective of this paper is to provide the ASME PRA Standard-based evaluation result for the existing KSNP Level 2 LERF model and the insights obtained from the evaluation process
This paper seeks to challenge the traditional way in which we assess the value of green buildings in terms of their environmental friendliness, energy efficiency and whole life cost. In the UK, quantity surveyors (or cost consultants) have a perception that more energy efficient and environmentally friendly buildings cost between 5% and 15% more to build from the outset. This common assumption is not backed up by recent research and should be questioned. Construction professionals need to be informed of the whole life cost and environmental impact of buildings so that they can encourage key stakeholders to make more sustainable choices. These emerging issues together with practical tools are considered with case studies from recent projects. (Author)
At present, the mostly used and developed mechanism is hardware virtualization which provides a common platform to run multiple operating systems and applications in independent partitions. More precisely, it is all about resource virtualization as the term hardware virtualization is emphasized. In this paper, the aim is to find out the advantages and limitations of current virtualization techniques, analyze their cost and performance and also depict which forthcoming hardware virtualization techniques will able to provide efficient solutions for multiprocessor operating systems. This is done by making a methodical literature survey and statistical analysis of the benchmark reports provided by SPEC (Standard Performance Evaluation Corporation) and TPC (Transaction processing Performance Council). Finally, this paper presents the current aspects of hardware virtualization which will help the IT managers of the large organizations to take effective ...
Although good encryption functions are probabilistic, most symbolic models do not capture this aspect explicitly. A typical solution, recently used to prove the soundness of such models with respect to computational ones, is to explicitly represent the dependency of ciphertexts on random coins as labels. In order to make these label-based models useful, it seems natural to try to extend the underlying decision procedures and the implementation of existing tools. In this paper we put forth a more practical alternative based on the following soundness theorem. We prove that for a large class of security properties (that includes rather standard formulations for secrecy and authenticity properties), security of protocols in the simpler model implies security in the label-based model. Combined with the soundness result of (\\textbf{?}) our theorem enables the translation of security results in unlabeled symbolic models to computational security.
Summary Humans discount the value of future rewards over time. Here we show using functional magnetic resonance imaging (fMRI) and neural coupling analyses that episodic future thinking reduces the rate of delay discounting through a modulation of neural decision-making and episodic future thinking networks. In addition to a standard control condition, real subject-specific episodic event cues were presented during a delay discounting task. Spontaneous episodic imagery during cue processing predicted how much subjects changed their preferences toward more future-minded choice behavior. Neural valuation signals in the anterior cingulate cortex and functional coupling of this region with hippocampus and amygdala predicted the degree to which future thinking modulated individual preference fu...
An Environmental Impact Assessment (EIA) study for any project is a time- consuming process because it has a large number of dependent and independent variables that must be taken into account. Although EIAs are dependent on geo-spatial information in order to make an assessment, there are no standard rules for conducting an environmental assessment. In addition, each assessment objective is case-dependent, based on what information is available. This paper presents a new framework for the analysis phase of the Environmental Impact Assessment (EIA) for projects, based on the integration between remote sensing technology, geographic information systems, and spatial modeling. The framework comprehensively analyzes the environmental vulnerability around the project areas and its impact on the...
In this paper we propose an entropy measure for interval-valued intuitionistic fuzzy sets, which generalizes three entropy measures defined independently by Szmidt, Wang and Huang, for intuitionistic fuzzy sets. We also give an approach to construct similarity measures using entropy measures for interval-valued intuitionistic fuzzy sets. In particular, the proposed entropy measure for interval-valued intuitionistic fuzzy sets can yield a similarity measure. Several illustrative examples are given to demonstrate the practicality and effectiveness of the proposed formulas. We apply the similarity measure to solve problems on pattern recognitions, multi-criteria fuzzy decisionmaking and medical diagnosis.
Often ecologists and natural resource managers can easily access data on invasive species occurrence across a region. Yet, collecting species abundance data over a large area is arguably more important for decisionmaking, but inherently costly, so methods which can provide robust information at low-cost are particularly valuable. Studies of species distribution often use occurrence data to build models of the environmental niche. Environmental suitability derived from such models may be used to predict the potential distributions of species. The ability of such models to predict spatial patterns in abundance have recently been demonstrated. Here we tested the relationship of environmental suitability with local abundance of an aquatic invasive species, olive hymenachne (Hymenachne amplexi...
The study abstracted aims at analyzing the economic effects of energy policies using simulations. Emphasis is on assessing the effects of decisions in favour of an expanding electric power industry based on nuclear energy and hard coal. The study discusses alternative assumptions concerning the cost involved, pollution abatement measures, shutdown and dismantling costs etc. Input-output analyses make the simulation model a consistent vehicle. Besides, the model in question is characterized by its explaining the investment demand of the different sectors by referring to the continuous annual development of innovative technologies.
Reasons for variation in transfusion practice in orthopedic surgery are not well understood. This systematic review identified and appraised the quality of the literature in this area to assess the impact of factors associated with the use of allogeneic red blood cell (RBC) transfusion in orthopedic procedures. MEDLINE and EMBASE databases were searched for relevant English language publications. Articles containing a range of MeSH and text terms regarding ''blood transfusion,'' ''predictors,'' and ''multiple logistic regression'' were retrieved. Articles that focused on patients undergoing orthopedic procedures and that met prespecified inclusion criteria were appraised in terms of potential bias and the appropriateness of statistical approach. A total of 3641 citations were retrieved, an...
A pipeless batch plant is a batch processing production system using mobile vessels. The plant performances depend on both hardware of equipment and software of operation. So the plant includes many design factors such as number of vessels, stations and AGVS, layout of stations, vessel moving rules, job scheduling and so on. In this paper, the characteristics of pipeless batch plant design are considered to handle the problem by the systems engineering approach. Then, a practical design method known as design-by-analysis is applied to solve such a complex design problem. Based on this concept, a design support system composed of modeling, simulation and evaluation subsystems is developed. This system enables rational decisionmaking through performance evaluation for proposed design of a pipeless batch plant. The usefulness of the system is illustrated by industrial examples. 12 refs., 8 figs., 6 tabs.
The data mining process consists of a series of steps ranging from data cleaning, data selection and transformation, to pattern evaluation and visualization. One of the central problems in data mining is to make the mined patterns or knowledge actionable. Here, the term actionable refers to the mined patterns suggest concrete and profitable actions to the decision-maker. That is, the user can do something to bring direct benefits (increase in profits, reduction in cost, improvement in efficiency, etc.) to the organization's advantage. However, there has been written no comprehensive survey available on this topic. The goal of this paper is to fill the void. In this paper, we first present two frameworks for mining actionable knowledge that are inexplicitly adopted by existing research methods. Then we try to situate some of the research on this topic from two different viewpoints: 1) data mining tasks and 2) adopted framework. Finally, we ...
This paper presents a general high level estimation model of communication throughput for the implementation of a given communication protocol. The model, which is part of a larger model that includes component price, software driver object code size and hardware driver area, is intended to be general enough to be able to capture the characteristics of a wide range of communication protocols and yet to be sufficiently detailed as to allow the designer or design tool to efficiently explore tradeoffs between throughput, bus widths, burst/non-burst transfers and data packing strategies. Thus it provides a basis for decisionmaking with respect to communication protocols/components and communication driver design in the initial design space exploration phase of a co-synthesis process where a large number of possibilities must be examined and where fast estimators are therefore necessary. The fill model allows for additional (money) cost, software ...
Digital topographic models are the foundation of more advanced modeling applications and ultimately inform planning and decisionmaking in many fields. Despite this, the error associated with these models and derived attributes is commonly overlooked. Little attention has been given in the scientific literature to the benefits gained from having less error in a model or to the corresponding cost associated with reducing model error by choosing one product over another. To address these gaps in knowledge we evaluated the error associated with five digital elevation models (DEMs) and derived attributes of slope and aspect relative to the same attributes derived from LiDAR data. We also estimated the acquisition and processing costs per square kilometer of the five test models and the LiDAR m...
The project was initiated in 1985 with the goal of studying existing federal, state, and local programs for protecting and preserving Cape Cod's sole-source aquifer. To meet this need, the Massachusetts Department of Environmental Quality Engineering and the U.S. Environmental Protection Agency's Region 1 in cooperation with the Cape Cod Planning and Economic and Development Commission and the U.S. Geological Survey initiated a two-year study to determine the adequacy of current ground-water protection programs and to recommend improvements. In the process of gathering and evaluating hydrogeological data from the Towns of Barnstable and Eastham, the CCAMP Aquifer Assessment Committee developed the papers which are the subject of this publication. These studies formed the technical basis for groundwater resource management decisionmaking.
Today's building industry is promoting the use of renewable sources of energy to heat, cool, and illuminate commercial buildings. Societies such as the International Solar Energy Society sponsor conferences such as this one to share knowledge and experience in the area of solar energy. However, the technologies presented here assume a need for heating, cooling or illumination. A simple technique is presented for determining the actual heating, cooling, and lighting requirements for commercial buildings, and for reducing those requirements through proper building design before applying solar technologies. The energy nomographs are a graphic energy design tool developed to aid designers in making cost effective decisions about energy alternatives early in the design process. Reducing loads at this point can help reduce the expense of a passive or active solar system which is usually sized to meet a certain percentage of the annual loads.
Technologies and practices that recover energy and materials from municipal solid waste present a technically and economically viable alternative to sanitary landfills and other solid waste disposal methods. However, community planners considering resource recovery should be aware of the potential environmental impacts of proposed projects. To assess these impacts, a planner should: identify the most significant types of impacts; establish boundaries beyond which impacts are not significant; characterize the environment as it would exist without the proposed project over the project's lifetime; predict the magnitude, and the distribution over time and space, of potential impacts; and relate the magnitude of predicted impacts to a scale of significance that will allow environmental values to be considered in decision-making. 24 references, 1 table.
Restructuring of power system has changed the traditional planning objectives and introduced challenges in the field of Transmission Expansion Planning (TEP). Due to these changes, new approaches and criteria are needed for transmission planning in deregulated environment. Therefore, in this paper, a dynamic expansion methodology is presented using a multi-objective optimization framework. Investment cost, congestion cost and reliability are considered in the optimization as three objectives. To overcome the difficulties in solving the non-convex and mixed integer nature of the optimization problems, a Non-Dominated Sorting Genetic Algorithm (NSGA II) approach is used followed by a fuzzy decisionmaking analysis to obtain the final optimal solution. The planning methodology has been demonstrated on the IEEE 24-bus test system and north-east of Iran national 400 kV transmission grid to show the feasibility and capabilities of the proposed ...
The US Department of Energy (DOE) is now evaluating its facility requirements in support of its cleanup mission at Hanford. One of the early findings is that the 200-Area steam plants, constructed in 1943, will not meet future space heating and process needs. Because the 200 Area will serve as the primary area for waste treatment and long-term storage, a reliable steam supply is a critical element of Hanford operations. This Analysis and Decision Document (ADD) is a preliminary review of the steam supply options available to the DOE. The ADD contains a comprehensive evaluation of the two major acquisition options: line-term versus privatization. It addresses the life-cycle costs associated with each alternative, as well as factors such as contracting requirements and the impact of market, safety, security, and regulatory issues. Specifically, this ADD documents current and future steam requirements for the 200 Area, describes alternatives ...
Indicators are important tools for communicating and making accessible scientific and technical information to policymakers and the general public. They therefore play an important role in transforming information into action. Worldwide, many initiatives are underway to construct indicators for a variety of purposes, including those for reporting on sustainable development. This paper briefly describes the attempts made so far, but stresses that the users of the indicators should play a greater role in indicator construction. In developing countries, a substantial lack of data has meant that specific policy formulation may develop without adequate technical input. In developed countries also, data gaps may hinder policy formulation, implementation, and evaluation. However, the development of indicators as tools to assist in the management of hazardous wastes and toxic chemicals is still in the early stages of formulation. A more imaginative program of indicators ...
To develop a work in an area with high radiation, it requires of a detailed knowledge of the surroundings work, a communication and effective vision, a near dosimetric control. In a work where the spaces variables and reduced accesses exist, noise that hinders the communication, defendant operative condition, radiation field and taking of decision, it is necessary to have tools that allow a total control of the environment to make opportune and effective decisions, there where the task is developed. Under this elementary concept, it was developed in the Laguna Verde Central a project that it allowed a mechanism, interactive of control in spaces complex; to see, to hear, to speak, to measure. This concept takes to the creation of an equipped system with closed circuit of television, wireless communication systems, tele dosimetry wireless systems, VHS and DVD recording equipment, uninterrupted energy units. The system ...
The hydroelectric industry's recognition of the importance of avoiding unexpected failure, or forced outages, led to the development of probabilistic, or risk-based, methods in order to attempt to quantify exposures. Traditionally, such analysis has been carried out by qualitative assessments, relying on experience and sound engineering judgment to determine the optimum time to maintain, repair or replace a part or system. Depending on the nature of the problem, however, and the level of experience of those included in the decisionmaking process, it is difficult to find a balance between acting proactively and accepting some amount of risk. The development of a practical means for establishing the probability of failure of any part or system, based on the determination of the statistical distribution of engineering properties such as acting stresses, is discussed. The capacity-demand analysis methodology, coupled with probablistic, ...
In the safety assessment of a potential repository for spent nuclear fuel, it is important to assess the consequences of a hypothetical leak of radionuclides through the seabed and into a waterborne transport phase. Radionuclides adsorbed to sediment particles may be transported great distances through the processes of sedimentation and resuspension. This study investigates the transport patterns of sediment particles of two different sizes, released in the Forsmark and Laxemar area. The results show that the closed waters around Forsmark to a higher degree makes the particles stay in the area close to the release points
Oil and gas industry is the largest user of radioactive materials in Nigeria. They make use of radiation generators, sealed and unsealed radioactive sources.Some of these are potentially dangerous to human health and environment if not properly controlled. here is also the need to maintain control over occupational exposures to radiation, as well as to protect the public and the environment through proper management of wastes that may be radiologically hazardous. To minimize these, effective regulatory infrastructure is being put in place.For a smooth take-off of the nuclear power program, the National Nuclear Regulatory Authority and other stake holders in the nuclear industry need to start to put together licensing procedure for these.
It is estimated that more than 180.000 kilometres of onshore pipelines will be installed between now and 2012. According to the US Federal Office of Pipeline Safety report (1968-97), the average pipeline suffers one leak per year every 400 miles. This equates to a total of 180 expected leaks per year for a new pipeline alone. Sensornet's continuous real-time Digital Leak Detection monitoring solution has the reach, precision and the speed to provide complete, continuous real-time knowledge (author)
The aim of this document is to make a state-of-the-art of the techniques of heating-cooling ceilings and cold beams. These systems offer many advantages: they generate a high quality thermal comfort, they are energy efficient, and offer important room saving, particularly interesting in the case of building renovation. The document comprises 5 parts dealing with: 1 - the heating-cooling ceilings; 2 - the cold beams; 3 - the elements necessary for the dimensioning (building-system interactions, ventilation, temperature regulation and safety systems); 4 - dimensioning method; 5 - design, realization and operation: the rules to follow. (J.S.)
This work plan has been prepared to document the scoping and planning process performed by the US Department of Energy (DOE) to support remedial action activities at the Colonie site. The site is located in eastern New York State in the town of Colonie near the city of Albany. Remedial action of the Colonie site is being planned as part of DOE's Formerly Utilized Sites Remedial Action Program. The DOE is responsible for controlling the release of all radioactive and chemical contaminants from the site. Under the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA), a remedial investigation/feasibility study (RI/FS) must be prepared to support the decision-making process for evaluating remedial action alternatives. This work plan contains a summary of information known about the site as of January 1988, presents a conceptual site model that identifies potential routes of human exposure to site containments, identifies data gaps, ...
Background: Accountability demands are increasingly pushing school leaders to explore more data and do more sophisticated analyses. Data-driven decisionmaking (DDDM) has become an emerging field of practice for school leadership and a central focus of education policy and practice. Purpose: This study examined principals' DDDM practices and identified the factors influencing DDDM using the theoretical frame of information use environments. Participants: Participants were 183 public high school principals in a Midwestern state. Research Design: The research design was cross-sectional survey research. Data Collection and Analysis: Survey instruments were developed and administered to principals. Structural equation modeling was conducted to determine what factors significantly affect principals' DDDM practices in different leadership dimensions. Findings: Principals used data more frequently in instructional and organization operational ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation's need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to ...
In May 2002, the United States Department of Energy (DOE) signed Assistance Instrument Number DE-FC09-02CH11109 with the Medical University of South Carolina (MUSC) to support the Environmental Biosciences Program (EBP). This funding instrument replaces DOE Assistance Instrument Number DE-FC02-98CH10902. EBP is an integrated, multidisciplinary scientific research program, employing a range of research initiatives to identify, study and resolve environmental health risks. These initiatives are consistent with the MUSC role as a comprehensive state-supported health sciences institution and with the nation s need for new and better approaches to the solution of a complex and expansive array of environment-related health problems. The intrinsic capabilities of a comprehensive health sciences institution enable MUSC to be a national resource for the scientific investigation of environmental health issues. EBPs success as a nationally prominent research program is due, in part, to its ...
Life cycle oriented methods are increasingly used for environmental assessments (EAs) of the built environment. However, many assumptions are made in such assessments, potentially influencing the results and making the assessment more ambiguous. To increase the reliability of EAs, consequences of the assumptions made have to be better understood. Since energy use in the operation and maintenance phase is an important factor decisive for the overall environmental performance of a building, the purpose of this study is to investigate how the selection of heat and electricity mix affects the assessed environmental performance of buildings. It also aims to suggest how to choose heat and electricity data in EAs of the built environment in general. Applying four different modes of electricity production and two different modes of heat production in a case study of three different buildings with different technical solutions for heat and electricity ...
The European Court of Justice has defined a clear means by which waste utilisation methods can be distinguished from waste disposal methods in a logical, well-understandable manner. With its stringent definition of ''utilisation'' this judgement points the way to quality-oriented waste management practices. We do not share the often voiced fear that this decision will lead to an increased incineration of compound wastes in industrial plants such as cement works. From the fact that, according to the decision by the European Court of Justice, wastes destined for utilisation fulfil a certain purpose and therefore, if not available in sufficient quantity must be replaced by primary raw materials, it follows that these wastes are required to fulfil specific quality criteria. This is rarely the case, if at all, with compound wastes. From the viewpoint of Luxembourg the decision by the European ...
The world's fleet of nuclear power plants is, on average, more than 20 years old. Even though the design life of a nuclear power plant is typically 30-40 years, it is quite feasible that many plants will be able to operate in excess of their design lives, provided that nuclear power plant engineers demonstrate by analysis, trending, equipment and system upgrades, increased vigilance, testing and ageing management that the plant will operate safely. In the operation of nuclear power plants, safety should be always the prime consideration. Plant operators and regulators must always ensure that plant safety is maintained, and where possible enhanced, during a plant's operating lifetime. Nuclear power plant life management (PLiM) has gained increased attention over the past decade, and effective ageing management of systems, structures and components (SSCs) is a key element in PLiM for the safe and reliable long term operation of nuclear power ...
The slow or stagnant rate of nuclear power generation development in many developed countries over the last two decades has resulted in a significant shortage in the population of mid-career nuclear industry professionals. This shortage is even more pronounced in some specific areas of expertise such as radiological protection, waste management and decommissioning. This situation has occurred at a time when the renaissance of nuclear power and the globalization of the nuclear industry are steadily gaining momentum and when the industry's involvement in international and national debates in these three fields of expertise (and the industry's impact on these debates) is of vital importance. This paper presents the World Nuclear Association (WNA) approach to building and enhancing worldwide industry cooperation in radiological protection, waste management and decommissioning, which is manifested through the activities of the two WNA working groups on radiological protection (RPWG) and on ...
Full text: The site selection process for a near surface repository dedicated for the radioactive waste resulted from the Cernavoda NPP operation and decommissioning started early in 90's. Each site selection stage included the collection of data from specific field and laboratory works as well as the appropriate safety performance evaluation. In order to assess/confirm the performance of the natural barrier of the Saligny site, the radionuclide concentration in the disposal system compartments has been evaluated, as complementary safety indicator of repository. The siting process was made in accordance with national and international regulations and standards and using a conceptual design similar to those used at L'Aube (France), ElCabril (Spain) or Mohovce (Slovak Republic). ANDRAD, the Romanian waste management organization that has continued the siting process in the last three years applied and obtained a partial siting license from CNCAN ...
A knowledge-based expert system has been developed to support human decision makers who assess drug products for inclusion in the Saskatchewan Formulary. Formulary inclusion and deletion decisions...Full Text Available
In 1998, EU legislation initiated a liberalisation process among European energy markets. The process of market opening has significantly changed the functioning of the markets and the competition conditions of the energy sector. At the same time, the industry witnessed a surge of mergers and far-reaching changes in the structure of German electricity and natural gas markets occurred. Against this background, the doctoral thesis at hand surveys the merger activities in the energy sector as well as the merger control policy of the German Federal Cartel Office during the first years of liberalisation. The study starts with a portrayal of the institutional framework of the German merger control regime and a survey of the relevant economic literature on horizontal and vertical mergers. Subsequent to the legal and theoretical considerations, the merger activities and the merger control policy of the German Federal Cartel Office are investigated empirically. The data set is based on ...
In these years Information Technology has been used in activities that require an intelligent intervention. In this context take placing Decision Support Systems, since they use Information Technology to support users in decision processes, that is problems of logical level greater then problems normally treated by traditional information systems. The purpose of this work is to describe Decision Support Systems specifying what they are, their functionally and structure, identifying, furthermore, user types referred to and interaction modality between them; and to present a prototype of these systems. From a preliminary analyses phase of ENEA being and its Information Systems to understand which topics can be supported by systems of this type, it deals with one of these topics: weighing of new project, finding parameters, or key quantity, that affect and determine decisions. It describes, then, models, ...
Human resource competence building and continued enhancement of performance is the most vital input for safe and reliable operations of a Nuclear Power Plant. Integrated planning leading to the decision of timely selection of optimum number of fresh people and deployment of experienced manpower with desired lead time is inevitable to achieve the above objective. For safe and reliable plant operation human performance analysis followed by suggestive measures to improve the same is needed. Corrective or strengthening input may be in terms of training, work environment, motivations, organizational culture and climate, leadership and prevailing environmental force and bio-rhythm of individuals with critical days are to be worked out The adequacy in training and development not only gives safe and reliable plant operations but results in greater employee satisfaction and self esteem as well. As of date, in the present vibrant global scenario, only the organization which ...
With the development of the latent heat store and its inclusion in the conventional heating control of cars, success has been achieved both in increasing comfort and in making an important contribution to safety of driving. Great store is set in development of the system on its environmental friendliness, for example by the thorough use of environmentally friendly and reusable materials. This also means the use of clean materials. It was shown that the latent heat store (apart from the aspects of comfort and safety of driving) can also make a contribution to saving fuel and reducing the exhaust gas. The sum total of the advantages makes it clear that the latent heat store introduced here is a very environmentally friendly system with multi-functional properties. (orig.) [Deutsch] Mit der Entwicklung des Latentwaermespeichers und seiner Einbindung in die konventionelle ...
In 2005, the American Medical Informatics Association undertook a set of activities relating to clinical decision support (CDS), with support from the office of the national coordinator and the Agency...Full Text Available
This paper proposes a novel and efficient algorithm to obtain optimal generation dispatch reflecting the operator's intention in power system rescheduling. In optimal system operation, various objectives, such as economy, quality and transmission security, need to be achieved simultaneously. However, these objectives are often contradictory and in a trade-off relationship with respect to each other thus making it difficult to handle this class of problem by conventional approaches. In the proposed algorithm, optimal generation dispatch is formulated as a multi-objective optimization problem. A fuzzy coordination technique based on fuzzy set theory is used to obtain an optimal solution. Evaluation indices composed of fuel cost, transmission line overload and AFC regulation capacity margin are measured by the membership functions, and multi-objective optimization is solved by maximizing the composite performance index, namely, the fuzzy ...
Within its competence for energy research, the Bundesministerium fuer Wirtschaft und Arbeit (BMWA) (Federal Ministry of Economics and Technology) sponsors investigations into the safety of nuclear power plants. The objective of these investigations is to provide fundamental knowledge, procedures and methods to contribute to realistic safety assessments of nuclear installations, to the further development of safety technology and to make use of the potential of innovative safety-related approaches. The Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) mbH, by order to the BMWi, continuously issues information on the status of such investigations by publishing semi-annual and annual progress reports within the series of GRS-F-Fortschrittsberichte (GRS-F-Progress Reports). Each progress report represents a compilation of individual reports about the objectives, work performed, ...
Waste management has gone through a history of shifting problems, demands, and strategies over the years. In contrast to the long prevailing view that the problem could be solved by hiding or moving it, waste is now viewed as a problem ranging from local to global concern, and as being an integral part of several sectors in society. Decisive for this view has been society's increasing complexity and thus the increasing complexity of waste, together with a general development of environmental consciousness, moving from local focus on point emission sources, to regional and global issues of more complex nature. This thesis is about the development and application ORWARE; a model for computer aided environmental systems analysis of municipal waste management. Its origin is the hypothesis that widened perspectives are needed in waste management decision-making to avoid severe sub-optimisation of environmental performance. With a strong ...
This monograph provides basic notions and principles in dosimetry and radiation protection in compliance with two fundamental works: IAEA Safety Series No.115 - International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources - and Publication no. 60 of International Commission on Radiological Protection. After the review of quantities and units necessary in radiation protection, the book presents the new values of dose limits as well as the values of 'radiation weighting factor', 'tissue weighting factor' and 'conversion factor intake-dose' (committed effective dose per unit intake) by ingestion and inhalation for 30 most important radionuclides. The new values of dose limits, lower than the old values, are a challenge for the radiation protection, especially of the 'public' where the dose limit diminished by a factor of five relative to the earlier edition. The new ...
The procedure was developed to enable STUK (Radiation and Nuclear Safety Authority) to make simplified estimates on off-site consequences based on the existing results of the PSA level 2 calculations done by e.g. power utilities. Method is based on dose calculated from each nuclide group of reactor activity inventory when the same release fraction for each group is assumed. This means that a specific new result from PSA level 2 can be categorised to find out a representative PSA level 3 result for this case. In addition a user interface including the procedure was prepared. Secondly some new insights about consequences based on the releases from PSA level 2 is expected to give better understanding of risks at prevailing increased reactor power levels. In this case only some early health effects and long-term doses were estimated without full-scope PSA level 3 approach. (orig.)
JAERI has been performing transient core thermal-hydraulic test program. In the program, authors performed BWR/ABWR DBE simulation tests with a test facility, which can simulate BWR/ABWR transients. The test facility has a 4 x 4 bundle core simulator with 15-rod heaters and one non-heated rod. Through the tests, authors quantified the thermal safety margin for core cooling. In order to quantify the thermal safety margin, authors collected experimental data on post-CHF. The data are essential for the evaluation of clad temperature transient when core heat-up occurs during DBEs. In comparison with previous post-CHF tests, present experiments were performed in much wider experimental condition, covering high clad temperature, low to high pressure and low to high mass flux. Further, data at wider elevation (lower to higher elevation of core) were obtained in the present experiments, which make possible to discuss the effect of ...
The present publication is based on facts, data, knowledge and projects, which have been incorporated in the development of an energy concept for the district Schmalkalden-Meiningen. The energy concept of a district is a concept oriented at action on and realisation of mid-term and long term decisions in the fields of energy policy, economy and ecology, which must be taken by municipal and economic decision-making bodies. The energy concept accords with the targets of the Agenda 21, the environmental targets of the Federal Republic of Germany and of the Land Thuringia. Accepting this energy concept the district Schmalkalden-Meiningen shows its willingness to contribute to a lasting development in all fields of economy and ecology and thus does justice to its increasing responsibility. (orig.) [German] Die vorliegende Veroeffentlichung baut auf Fakten, Daten, Erkenntnissen und Projekten auf, die in die Erarbeitung des Energiekonzeptes fuer den ...
During 1994 and the early part of 1995, the US Department of Energy's Yucca Mountain Site Characterization Office (YMSCO) and its parent organization, the Office of Civilian Radioactive Waste Management (OCRWM) underwent a significant restructuring. Senior Department officials provided the leadership to reorient the management, technical, programmatic, and public interaction approach to the US High Level Radioactive Waste Disposal Program. The restructuring involved reorganizing the federal staff, conducting meaningful strategic planning, improving the management system, rationalizing contractor responsibilities, focusing upon major products, and increasing stakeholder involvement. The restructured program has prioritized technical and scientific activities toward meeting major regulatory milestones in a timely and cost-effective manner. This approach has raised concern among elements of technical, scientific, and oversight bodies that suitability and licensing ...
Many electric power utilities are currently employing machine condition monitoring technologies as a means of reducing forced outages and controlling repair costs. These condition monitoring technologies are a set of {open_quotes}tools{close_quotes} to help maintenance and operations personnel identify and repair machinery problems before catastrophic failure occurs. In this way, the analysis of this data becomes a vital link in the daily operation of the plant. Machinery vibration analysis, machinery balancing and alignment, motor current testing, periodic thermography surveys, analysis of lubrication oil samples, performance monitoring, chemistry monitoring, ultrasonic leak detection surveys, and non-destructive inspections are some of the technologies available to perform this condition monitoring. However, even for a small or medium size plant, the sheer volume of data provided by applying all or some of these technologies can be staggering, not to mention the need to consider ...
Laparoscopic orchiopexy has gained popularity in recent years. However, the decision when to perform one-stage laparoscopic orchiopexy without division of the spermatic vessels versus initial ligation of the spermatic vessels followed later by orchiopexy is not clear. A new laparoscopic classification to facilitate decision-making during laparoscopy, according to the position of the impalpable testis and the relation of the spermatic vessels and vas deferens to the internal ring, with a management protocol based on this classification is presented. Over a 2-year period, a total of 37 boys with 52 impalpable gonads underwent a laparoscopic procedure. Four laparoscopic types of testis were noted: type I: no testis visualized; type II: a testis seen at the internal ring with the vas and vessels looping to the internal ring; type III: testis at the internal ring, with vas and vessels going to the testis directly; and type IV: intra-abdominal testis ...
Groups are assigned or formed to perform tasks that one person cannot accomplish alone. This lesson describes the classification of work groups, group unity, leadership, motivation, recognition, conflict resolution, and remediation associated with managing groups and their activities. Advantages associated with group process include 1) the generation of better ideas, 2) ability to assume greater risks; make fewer errors; 3) the capacity for greater knowledge and 4) information, and for some problems, production of better decisions. Groups may be formal or informal. Formal groups may be organic, task-directed, or committees. Informal groups arise when it becomes obvious that a group will work better or may be formed by a discipline within the organization or through friendships. The size of the group its status within the organization, the goals established, and the dependence of the members on the group all may affect the cohesiveness of the ...
Executive summary 1. Few studies have to date explained consumer attitudes and purchase decisions with regard to genetically engineered food products. However, the increased marketing of genetically engineered food products and the considerable concern that consumers seem to express with regard to the technology call for the development of a theoretical basis for research into these issues. 2. The aim of the paper is to present three models which we have developed to explain consumer attitudes, buying behaviour and attitude change with regard to genetically engineered food products. All three models build on established consumer behaviour theory and on existing and comparable research in the field. 3. Consumer attitudes toward genetic engineering in food products are explained in an attitude model that builds on Fishbein's multiattribute attitude model. The model deviates from Fishbein's model in a number of ways: there is an explicit distinction between perceived ...
Our modern society is increasingly faced with challenges and problems that cannot be solved by a purely technical, political or social approach. Radioactive waste disposal site selection and management can be characterised as one of these challenges that require a transdisciplinary approach, integrating social, philosophical and ethical aspects in a 'technical' practice. Along the spirit of this transdisciplinary approach, and in order to ensure the necessary public support for a policy decision regarding this practice, stakeholder involvement is more and more seen as a necessary policy element in the decisionmaking process. The aim is to achieve the broad involvement of individuals from civil society, with significant representation from local communities, elected representatives and NGO's, as well as scientists from outside radioactive waste management organisations, together with established ...
In the last decade, interest has increased in coastal and freshwater wetland restoration and creation at all levels of government, in the scientific community, and in the private sector. US Environmental Protection Agency personnel agreed that there was a pressing need to determine how well created and restored wetlands compensate for losses permitted under Section 404 of the Clean Water Act. An effort was made to capture information not published elsewhere and incorporate it with published literature to produce a unique resource. The status report is the first major publication resulting from research initiated on wetland creation and restoration. Conceived as a mechanism for identifying the adequacy of the available information, this status report will help set priorities for the research program and provide Agency personnel with an analytical framework for making Section 404 permit decisions based on the status of the science of wetland ...
This paper reports some technical contributes related to the Kyoto Protocol and its application in Italian decisionmaking policy. [Italian] Il presente volume raccoglie una decina di contributi tecnici originariamente preparati o commissionati dall'ENEA, Ente Nazionale per le Nuove Tecnologie, l'Energia e l'Ambiente, in vista della Conferenza Nazionale Energia e Ambiente. Questa fotografia di una situazione in rapida evoluzione e' stata preparata da esperti del settore che contribuiscono a redigere il materiale tecnico di base utilizzato dai negoziatori nazionali durante le trattative internazionali e dai responsabili nazionali per avviare il processo di presa di decisioni in materia.
The organization of the Biofuels Excellence Network, inside PROMINP - the Program of Mobilization of the National Industry of Oil and Natural Gas, has the objective of improving the actions of technical innovation and management in the chain of Oil, Gas Natural and Biofuels, through the optimized use of physical, financial, technological resources, of information and staff, with maximum qualification in areas of the human knowledge, whose purpose is to makedecisions on specific problems of improvement of processes and/or products, besides promoting actions for the development and reinforcement of the markets of ethanol and biodiesel. The organization of the Biofuels Excellence Network became necessary, in order to enable Brazil to reach vanguard standards in biofuels (ethanol and biodiesel) in a sustainable, competitive and environmentally responsible way. Among the main reasons for the creation of the Biofuels Excellence Network are: to speed ...
In pursuing its mission of helping U.S. independent oil and gas producers make timely, informed technology decisions, the Petroleum Technology Transfer Council (PTTC) functions as a cohesive national organization that implements industry's directives through active regional programs. The role of the national headquarters (HQ) organization includes planning and managing the PTTC program, conducting nation-wide technology transfer activities, and implementing a comprehensive communications effort. PTTC relies on 10 Regional Lead Organizations (RLOs) as its main program delivery mechanism to industry. Through its regions, PTTC connects with independent oil and gas producers--through technology workshops, resources centers, websites, newsletters, and other outreach efforts. The organization effectively combines federal, state, and industry funding to achieve important goals for all of these sectors. This integrated funding base, combined ...
We propose to investigate the in-medium properties of vector $\\omega$ mesons at the normal nuclear density in Ap(pA) collisions and at higher density in AA collisions at the ITEP accelerator facility TWAC. Using of the inverse Ap kinematics will permit us to study the $\\omega$ meson production in a wide momentum interval included the not yet explored range of small meson momenta relative to the projectile nuclei where the mass modification effect in nuclear matter is expected to be the strongest. Momentum dependence of the in-medium $\\omega$ meson width will be studied in the traditional pA kinematics. We intend to use the electromagnetic calorimeter for reconstruction of the $\\omega$ meson invariant mass by detecting photons from the $\\omega \\to \\pi^{0}\\gamma \\to 3\\gamma$ decay. The model calculations and simulations with RQMD generator show feasibility of the proposed experiment. Available now intensity of the ion beams provides a possibility to collect large statistics and ...
The main objectives of this study was to determine the bone density for the purposes of i) determining the age of peak bone mass in each study group and ii) quantifying the differences in bone density as functions of age and sex. The results of estimating the age dependence of mineral density for the femoral neck, spine and total body of healthy women and men using DEXA are given. The age changes in concentrations of major minerals and electrolytes found for compact and trabecular bones of healthy male femoral neck with regard for the wet and dry tissue calculations are represented. Information about femoral neck water content depending on the age of healthy men is tabulated. The number of performed observations and analyses is evidently insufficient to make any final decision, however some preliminary conclusions can be drawn. In accordance with DEXA results, BMD maximum for the femoral neck, spine and total body of healthy women is found for ...
This report examines the use of probabilistic methods in dealing with the problem of potential earthquake-induced liquefaction of foundation soils at an example dam site located in the central United States, near the New Madrid earthquake zone. The example dam is assumed to be a 1-mile long rolled-filled embankment founded on a 100-ft deep deposit of interbedded alluvial gravels, sands, silts, and clays. The study is seen as an opportunity to examine probabilistic concepts and procedures in the framework of an example engineering project. In this context, the main practical value of a probabilistic approach is that it permits more informed decisionmaking about further data acquisition, additional engineering analysis, and if necessary, remedial action. The specific aim of the study is to show how probabilistic procedures complement and help to reinterpret the results of deterministic (earthquake-induced) liquefaction analysis. The procedures ...
The Predictive Capability Maturity Model (PCMM) is a new model that can be used to assess the level of maturity of computational modeling and simulation (M&S) efforts. The development of the model is based on both the authors experience and their analysis of similar investigations in the past. The perspective taken in this report is one of judging the usefulness of a predictive capability that relies on the numerical solution to partial differential equations to better inform and improve decisionmaking. The review of past investigations, such as the Software Engineering Institute's Capability Maturity Model Integration and the National Aeronautics and Space Administration and Department of Defense Technology Readiness Levels, indicates that a more restricted, more interpretable method is needed to assess the maturity of an M&S effort. The PCMM addresses six contributing elements to M&S: (1) representation and geometric ...
In this paper the problem of developing optimal bidding strategies for the participants of oligopolistic energy markets is studied. Special attention is given to the impacts of suppliers' emission of pollutants on their bidding strategies. The proposed methodology employs supply function equilibrium (SFE) model to represent the strategic behavior of each supplier and locational marginal pricing mechanism for the market clearing. The optimal bidding strategies are developed mathematically using a bilevel optimization problem where the upper-level subproblem maximizes individual supplier payoff and the lower-level subproblem solves the Independent System Operator's market clearing problem. In order to solve market clearing mechanism the multiobjective optimal power flow is used with supplier emission of pollutants, as an extra objective, subject to the supplier physical constraints. This paper uses normal boundary intersection (NBI) approach for generating Pareto ...
Demands for electric power system, which include not only minimization of generation cost but also protection of environmental condition and maintenance of transmission security, have been diversified The priority of these objectives may change according to load change, weather, and other conditions. Since these objectives are usually in a trade-off relationship and generally non-commensurable, it is difficult to handle by conventional optimization of a single objective function. This report describes multi-objective scheduling of thermal power system. The adaptability of three performance indicies, such as economic efficiency, NO{sub x} emission, and transmission security, to operators are defined by membership functions in fuzzy set theory. coordinated solution in which the adaptability of operators is maximized can be obtained by maximizing the fuzzy decision-making function composed of the adaptability index for each objective. Because this coordinated solution ...
The US and UK have been separately working on the development of a NDA instrument to determine the enrichment of gaseous UF/sub 6/ at low pressures in cascade header pipework in line with the conclusions of the Hexapartite Safeguards Project viz. the instrument is capable of making a ''go/no go'' decision of whether the enrichment is less than/greater than 20%. Recently, there has been a series of very useful technical exchanges of ideas and information between the two countries. This has led to a technical formulation for such an instrumentation based on ..gamma..-ray spectrometry which, although plant-specific in certain features, nevertheless is based on the same physical principles. Experimental results from commercially operating enrichment plants are very encouraging and indicate that a complete measurement including set up time on the pipe should be attainable in about 30 minutes when measuring pipes ...
Licensing procedures are of great importance in the entire decision-making and planning process for erection of cogeneration power plants. The paper presented is a condensed version of the ASUE guide published in May 1999 and gives compact and topical information about legal and procedural aspects for orientation of people not yet familiar with the licensing procedures. An initial outline lists and characterises the procedures involved, which then are explained in greater detail, accompanied by flowsheets and diagrams. (orig./CB) [German] Genehmigungsverfahren besitzen im Entscheidungs- und Planungsprozess eine grosse Bedeutung. Um Planern, Bauherren und Behoerden hierzu einen kompakten und aktuellen Ueberblick bieten zu koennen, wurde dieses Referat als Kurzfassung der im Mai 1999 veroeffentlichten ASUE-Broschuere zusammengestellt. Sie bietet vor allem denjenigen eine Hilfestellung, die noch keine Erfahrungen mit den Genehmigungsverfahren gesammelt haben. ...
The LHC magnet tests operation team developed various innovative techniques, particularly since early 2004, to complete the superconductor magnet tests by Feb. 2007. Overall and cryogenic priority handling, rapid on-bench thermal cycling, rule-based goodness evaluation on round-the-clock basis, multiple, mashed web systems are some of these techniques applied with rigour for successful tests completion in time. This paper highlights these operation empowerment tools which had a pivotal role for success. A priority handling method was put in place to enable maximum throughput from twelve test benches, having many different constraints. For the cryogenics infrastructure, it implied judicious allocation of limited resources to the benches. Rapid On-Bench Thermal Cycle was a key strategy to accelerate magnets tests throughput, saving time and simplifying logistics. First level magnet appraisal was developed for 24 hr decisionmaking so as to ...
Alberta, Saskatchewan, and Manitoba, the three Prairie provinces of Canada, and their economies strongly depend on the petroleum industry. However, climate change may have potential impacts on the sector that could reverberate onto the socio-economic fabric of the provinces. The petroleum industry in the Prairies is faced with a big challenge: how to adapt to the changing climatic conditions so that they maintain or improve their economic and environmental efficiencies. The attitudes of the different stakeholders concerning climate change and the appropriate measures to be implemented by the petroleum industry were obtained through a questionnaire-based survey conducted between February and June 2001. Based on the responses received, a Chi-square statistical test was applied to look at the complex interactions in the results. An analysis of a number of petroleum-related processes and activities vulnerable to climate change was performed. A sound foundation was obtained for the ...
The cupola is a furnace used for melting steel scrap, cast iron scrap, and ferroalloys to produce cast iron. Its main energy source is coal coke. It is one of the oldest methods of producing cast iron, and it remains the dominate method because of its simplicity and low fuel cost. Cupolas range in size from 18 inches to 13 feet in diameter, and can produce up to 100 tons per hour of cast iron. Although cupola melting has a long history, automatic control has been elusive because the process has been poorly understood. Most foundries rely on the intuition of experienced operators to make control decisions. The purpose of this work, which has been underway for three years of an anticipated four year program, is to develop a controller for the cupola using intelligent and conventional control methods. The project is a cooperative effort between the Idaho National Engineering and Environmental Laboratory, the Department of Energy Albany Research ...
This document describes the geology and hydrogeology at the former Advanced Coal Liquefaction Research and Development (ACLR&D) facility in Wilsonville, Alabama. The work was conducted by personnel from the Oak Ridge National Laboratory Grand Junction office (ORNL/GJ) for the U.S. Department of Energy (DOE) Pittsburgh Energy Technology Center (PETC). Characterization information was requested by PETC to provide baseline environmental information for use in evaluating needs and in subsequent decision-making for further actions associated with the closeout of facility operations. The hydrogeologic conceptual model presented in this report provides significant insight regarding the potential for contaminant migration from the ACLR&D facility and may be useful during other characterization work in the region. The ACLR&D facility is no longer operational and has been dismantled. The site was characterized in three phases: the first two phases were an ...
New interest by Australians in the state of rural education requires new understanding of factors affecting rural education and its related issues. Educational programs have not been flexible enough to cope with rural diversity, a key element in the milieu. Standards such as "equality of opportunity" and "uniformity" have been misapplied to rural Australian education, which is made distinctive by the inter-relatedness of many factors. Three dimensions of isolation are discussed: (1) types of isolation (geographic, cultural, social, and professional isolation); (2) ways of coping with isolation (understanding isolation, developing a sense of community, developing awareness of options, training the isolated, application, and technology); and (3) conditions affecting educational changes in isolated communities (social and political climate, pedagogy, finance, and incentives for change). All these concerns focus on the issue of local control. Formal school systems control programs but ...
Large-scale field tracer experiments have been conducted on Ulchin and Wolsung nuclear sites for the purpose of validating FADAS and of analyzing the environmental characteristics around the nuclear site. The most influential factor in atmospheric dispersion is the meteorological condition. During the experiment, meteorological data were measured on the release point and the selected positions among sampling points. Once radioactive materials are released to the atmosphere, members of public may be exposed through the environmental media such as air, soil and foods. Therefore, to protect the public, adequate countermeasures should be taken at due time for those exposure pathways. Both processes of justification and optimization are applied to a countermeasure simultaneously for decision-making. The work scope of biological research for the radiation protection had contained the search of biological microanalytic methods for the assessment of health effect by ...
One of the principal problems confronting the remediation of Bear Creek Valley is the cleanup of contaminated groundwater. The S-3 Site is one of the locations in the valley where groundwater is most contaminated, and contamination from the S-3 Site has also caused extensive contamination of downgradient groundwater. This groundwater plume, therefore, has a high priority in the Bear Creek Valley remedial process. Pumping and treating groundwater was identified early in the feasibility study as a likely remedial alternative for the S-3 Site groundwater plume. The hydrology and geochemistry of the plume are extremely complex. There is a high degree of uncertainty in the current understanding of how the aquifer will react physically and chemically to pumping, making evaluation of a pump-and-treat alternative impractical at the present time. Before a pump-and-treat alternative can be evaluated, its technical practicability, effectiveness, and projected cost must be ...
The SCILS program investigates and demonstrates concepts of operation for dispersed theater forces C3. The dispersal concept would increase the number of potential targets for nuclear strike, make these targets smaller, more highly mobile and harder to find, and introduce functional redundancy. The SCILS system is a microcomputer-based approach to preserving and enhancing the effectiveness of C3 operation in a dispersed configuration. In this program, the system was implemented for testing for the 9th Infantry Division in coordination with the Army's Distributed Command and Control System. Technical highlights of the system include a distributed, replicated data base, a video map/graphics-oriented Commander's Decision Display System, a packet switched Multi-Media Network that operates with deployed field communication systems, and a Voice/Data Conferencing System that supports remote coordination/briefing in a dispersed ...
Expedited site characterization (ESC), developed by Argonne National Laboratory, is an interactive, integrated process emphasizing the use of existing data of sufficient quality, multiple complementary characterization methods, and on-site decisionmaking to optimize environmental site investigations. The Argonne ESC is the basis for the provisional ESC standard guide of the ASTM (American Society for Testing and Materials). QuickSite{sup SM} is the implementation package developed by Argonne to facilitate ESC of sites contaminated with hazardous wastes. At various sites, Argonne has successfully implemented QuickSite{sup SM} and demonstrated the technical superiority of the ESC process over traditional methodologies guided by statistics and random-sampling approaches. A key feature in the success of QuickSite{sup SM} investigations is achieving an understanding of the subsurface geologic and hydrogeologic controls and processes at a site ...
Soil erosion by water is recognised as a major soil degradation process that requires a global approach. Large regions all over the world are in need of integrated conservation strategies that sustainable prevent and remediate soil erosion. therefore, quantitative and globally interpretable data are needed in support of models and decisionmaking. the effects of various soil and water conservation techniques (SWCT) on runoff and soil loss in Europe have been extensively studied over the last 60 years. Runoff plots are the most widely used measurement technique to study the effects of SWCT on runoff and soil loss by water erosion. Hence, many data are available. However, the insights gained hereby remain mostly local and often qualitative whereas the full potential of the available data is not exploited yet. This is mainly due to the fragmentation of knowledge and extrapolation difficulties inherently linked with this type of data. (Author) 8 ...
Commercially available CT devices reconstruct cross-sectional slices of the human body. A sequence of such abutting cross-sectional slices can be, and usually is, used to obtain information about the region of the head, which requires several slices to cover it. However, there are situations for which such asequence of displays is far from optimal - for example, when one would like to see the anatomic relationship between two features appearing in different slices or the shape of a particular region or tumor. The Computer Aided Three-Dimensional Reconstruction and Imaging System (CATRIS), developed at our university, can build up a three-dimensional image from a series of CT cross-sections and can display its stereoscopic image on a three-dimensional graphic display system, thus providing helpful information for clinical use in recognizing the anatomic relationship between two features appearing in different slices or the shape of particular organ or tumor. This three-dimensional ...
Introducing intelligence by means of cognition for managing, protecting, processing, and delivering of information in mobile communication systems is the way towards ubiquitous, converged and secure communications. In this context, this paper introduces the concept of quality of information (QoI). QoI means QoS while all the requirements for dependability, security, privacy and trust are satisfied at the highest possible level. This work proposes and describes an approach to network monitoring in a heterogeneous communication environment based on use of cognitive techniques and learning predictive algorithms (e.g., fuzzy logic). These methodologies are used to create an autonomy in the decisionmaking process that is based on the calculation of key performance indicators (KPIs), which in their turn would trigger the needed radio resource management algorithms. The expected output is an improved network performance in terms of maximized ...
The author says ''barehand'' methods, where specially trained utility workers are called in conductive suits to equalize voltage over their bodies, to maintain high-voltage transmission lines are on the rise. Utilities are building lines at higher voltages and selling more power to other utilities, making it highly inconvenient to take the lines out of service. However, some unions view the barehand work with less than enthusiasm. Touching lines energized at hundreds of thousands of volts demands flawless equipment and rigid work procedures followed to the letter. Some local unions contend that adequate safety procedures and training, and appropriate penalties for workplace negligence, should be in place before utilities may do barehand work. The author discusses some of the methods of barehand work and the equipment used, i.e. steel-mesh lineman's suit, bucket truck's boom, helicopters, and robots.
To make a quantitative comparison of risks between the SNR-300 and a modern PWR (Biblis B), the consequences of an accident or the extent of damage of a release of radionuclides to the environment due to an accident are estimated by computer programs for accident consequence models. The accident analysis includes an analysis of events for Bethe-Tait accidents with failure of the outer containment. The FGSB release rates are compared with those of the Society for Reactor Safety (GRS).
The purpose of this paper is to relate some of the commonly encountered problems with operational procedures in the nuclear industry and offer practical suggestions for their elimination. The paper is based on recent consultant experience in assisting industry clients with human performance related design and assessment initiatives. Operational procedures are a key part of an integrated system design. Procedures provide the specified instructions for actions people are to undertake in operating a facility to achieve production and safety goals. While organizations continue to make substantial investments in procedure development and maintenance, problems with procedures continue to occur, as evidenced through operating inefficiencies, errors, and events. The paper reviews the role procedures play in facility operations, comments on current development and maintenance practices, discusses the extent of human performance related problems ...
We review and extend in several directions recent results on the asymptotic safety approach to quantum gravity. The central issue in this approach is the search of a Fixed Point having suitable properties, and the tool that is used is a type of Wilsonian renormalization group equation. We begin by discussing various cutoff schemes, i.e. ways of implementing the Wilsonian cutoff procedure. We compare the beta functions of the gravitational couplings obtained with different schemes, studying first the contribution of matter fields and then the so-called Einstein-Hilbert truncation, where only the cosmological constant and Newton's constant are retained. In this context we make connection with old results, in particular we reproduce the results of the epsilon expansion and the perturbative one loop divergences. We then apply the Renormalization Group to higher derivative gravity. In the case of a general action quadratic in curvature we recover, ...
Inherent boron dilution can occur in case of a Small Break LOCA when low borated water is mainly accumulated in the U-legs due to reflux boiling in the Steam Generator tubes after the loss of natural circulation. The restart of the natural circulation may lead to criticality because of the injection of these low borated slugs towards the core. To evaluate this potential risk, the boron concentration at the core inlet has to be known which makes necessary to estimate the mixing phenomena in the cold leg, in the downcomer and in the lower plenum: CFD calculations are required. First of all the validation of CFX5 CFD code on the relevant phenomena of inherent boron dilution has been established (UPTF TRAM C3 test). Then, an application to the 900 MW French Pressurized Water Reactor series has been performed. (authors)
The detection and characterization of deeply buried fatigue damage in thick, multi-layer airframe components pose significant technical challenges to the aviation safety community. Currently, no nondestructive evaluation technique is available to reliably detect such potential damage from the exterior of the airframe, which is highly desirable in light of inspection cost as well as avoidance of structure damage. Recent technological advances in high-sensitivity magnetic sensors, i.e., spin-dependent tunneling (SDT) sensors, make it feasible to employ electromagnetic inspection techniques for deep fatigue crack inspection. In this work, we report on the development and fabrication of a low frequency eddy current probe based on a magnetically shielded SDT pickup sensor concentrically located...
Inherent boron dilution can occur in case of a small Break LOCA when low borated water is accumulated in the U-legs due to reflux boiling in the Steam Generator tubes after the loss of natural circulation. The restart of the natural circulation may lead to criticality because of the injection of these low borated slugs towards the core. To evaluate this potential risk, the boron concentration at the core inlet has to be known which makes necessary to estimate the mixing phenomena in the cold leg, in the downcomer and in the lower plenum: CFD calculations are required. First of all the validation of CFX5 CFD code on the relevant phenomena of inherent boron dilution has been established (UPTF TRAM C3 test). Then, an application to the 900 MW French Pressurized Water Reactor series has been performed. (authors)
The purpose of this paper is to compare the techniques and results obtained when a general industrial or commercial building power electrical system is prepared using the US National Electrical Code{copyright} (NEC) and the International Electrotechnical Commission (IEC) Standards. The final design offer the reader the possibility of making an initial comparison and analyzation of the two methods based of their overall effectiveness (sizing, protection, co-ordination of protective devices with components etc.), safety and cost. In order to make such a comparison a specific example was developed and limited in detail to avoid complexity in this study. The power source selected will be a delta-wye utility supplied transformer feeding various load groups such as lighting and motor circuits (possibly through associated transformers). Relevant NE Code references, IEC standards, and appropriate justifications will be made at ...
As the nuclear world is changing, the non-proliferation and safeguard systems have to change along the global development. Nuclear security as well as safety must be involved in all phases. Thus, modernization of thinking is a must. State system of accounting for and control of nuclear material (SSAC) is a basis, but now it is time to move ahead. Safeguards is not any more only to verify the declared nuclear materials but it is to inform the international safeguards society transparently but confidentially about the nuclear fuel cycle related activities and trade, and to confirm that there are no undeclared activities related to the nuclear fuel cycle in the states. Only strong SSAC with enhanced capabilities, activities and rights can meet the demand. The proliferation of nuclear weapons is a threat that also urges cooperation at all levels. International, regional and state systems must work closely together, and there is need and space for everyone. State ...
Topics concerning the problems associated with older and aging dams are considered including: what can be done to extent the lifetime of an old dam, the decision to decommission a dam based on a value judgment that the risk of maintaining the dam is too great for society's acceptance, the possibility of change in the level of risk tolerance with time in a technological environment, traditional surveillance methods used by dam owners in the Y2K situation, and the unreality of dam immortality. Trends and means for preserving older dams for their owner's purposes are outlined, as well as their lifetime compared to that of the downstream systems they serve. Despite the fact that we live in a throwaway society, dam owners cannot just leave their dam asset when they are through with using it. Someone has to maintain the dam, or ensure that it is safely decommissioned when the owner is finished with it. On a worldwide scale the available pool of ...
In order to build the safety culture for nuclear power industry, it is important to evaluate the safety culture scientifically. Considering the traits of safety culture in the nuclear power industry, 24 safety culture assessment indexes are established from 4 aspects such as Safety consciousness, Safety attitude, Safety action and Safety actuality by using the SMART criteria. Safety culture star-class assessment criterion is presented and safety culture star-class assessment system is developed by using Visual Basic 6.0 and BP neural network. The system has a better generalization ability, and it can show exactly which phase the safety culture is in. Experimental results show that safety culture star-class assessment is practical and easy ...
The strategy for building SASOL plants reflects a commitment to long-range planning. The first plant, which represented a large investment for a moderate production capacity, was built to establish a technology for reducing South Africa's dependence on imported motor fuels. After the success of the plant, SASOL made plans for a larger plant, which had to be justified solely on economic grounds. At that time, petroleum crude was cheap and plentiful, and the second plant was cancelled. But when OPEC formed and the price of petroleum crude was increased, the South African government reconsidered the plans for another SASOL plant. Furthermore, because the cost of fuels produced at Sasol I proved to be significantly insensitive to inflation and future OPEC price increases were expected, SASOL projected that a new, larger plant should make a profit within a few years after its initial operation. But OPEC prices and inflation have risen even faster than ...
The strategy for building SASOL plants reflects a commitment to long-range planning. The first plant, which represented a large investment for a moderate production capacity, was built to establish a technology for reducing South Africa's dependence on imported motor fuels. After the success of the plant, SASOL made plans for a larger plant, which had to be justified solely on economic grounds. At that time, petroleum crude was cheap and plentiful, and the second plant was cancelled. But when OPEC formed and the price of petroleum crude was increased, the South African government reconsidered the plans for another SASOL plant. Furthermore, because the cost of fuels produced at Sasol I proved to be significantly insensitive to inflation and future OPEC price increases were expected, SASOL projected that a new, larger plant should make a profit within a few years after its initial operation. But OPEC prices and inflation have risen even faster than ...
A scheme for on-line tuning of a fuzzy-logic power system stabilizer is presented. firstly, a fuzzy-logic power system stabilizer is developed using speed deviation and accelerating power as the controller input variables. The inference mechanism of fuzzy-logic controller is represented by a decision table, constructed of linguistic IF-THEN rules. The Linguistic rules are available from experts and the design procedure is based on these rules. It assumed that an exact model of the plant is not available and it is difficult to extract the exact parameters of the power plant. Thus, the design procedure can not be based on an exact model. This is an advantage of fuzzy logic that makes the design of a controller possible without knowing the exact model of the plant. Secondly, two scaling parameters are introduced to tune the fuzzy-logic power system stabilizer. These scaling parameters are the outputs of another fuzzy-logic system, which gets the ...
Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies in rapidly-growing economies in the developing world will be an essential component of global efforts to alter the path of ...
One of the aims in the safety assessment of SFR-1 is to estimate the release to the environment. In order to make these calculations there is a need to describe the inventory in greater detail. The new computerised database of waste in SFR-1 gives a good possibility to achieve this. The aim for project SAFE is to make both conservative and realistic radionuclide transport calculations. To achieve this goal there must be two inventories. The conservative inventory is the inventory used in the design of the repository, which in most parts is identical with the limits in the licence for SFR-1. There is a great interest to have good estimates of the volumes of the different waste types. A thorough prognosis should be made in 1999, but until then the latest one from 1995 could be used in the calculations. The total (actual) inventory of nuclides is calculated from the measurements of the easy-to-measure nuclides since, in ...
Different cases exist in various countries regarding the institutional status, the organization and the technical resources of the Nuclear Regulatory Authority (NRA): there are NRAs having extended internal technical capability and others relying mostly on external technical support. Considering the research and development activities and the very broad range of technical matters on which the regulatory and licensing activity are based, the NRA can not rely only on internal resources, and generally there is the need of technical and scientific support together with enhanced international cooperation. The international cooperation and networking among NRAs, and their Technical Support Organizations (TSO), represents a fundamental way to maintain competence, capability and knowledge. Within the EU member states this is becoming more and more an institutional duty. In providing technical support for regulatory activity, the experience shows, from one side, the importance to have TSO with ...
Critics of higher fuel economy standards for vehicles have long argued that improving vehicle fuel economy will require reducing vehicle weight, and that would result in an increase in the number of fatalities from vehicle crashes. Several researchers have estimated that an across-the-board reduction of vehicle weight would reduce passenger safety (Evans 1991; Kahane 1997; U.S. GAO 1994). However, little research has been done on the relationship of vehicle size and fatality rates, independent of weight (see, however, Joksch, Massie, and Pichler 1998). In this report we review previous analyses of the relationship of vehicle weight and safety. We do this to study the opportunities to improve fuel economy in a more sophisticated way than across-the-board mass reduction. The aim is to explore improvements in traffic safety by making selected vehicle groups lighter, and retaining or enlarging selected ...
Safety in general and harmonization of International Maritime Organization rules on mobile offshore drilling rig operation in particular are discussed. The improvement of the industry's safety record is also discussed.
Information about surface soil moisture conditions is of critical importance to real-world applications such as agricultural production, water resource management, flood prediction, fire prediction, water supply, military mobility, etc.. Near-surface soil moisture is currently available from non-ideal sensor configuration observations, and two missions targeted at measuring near-surface soil moisture with ideal sensor configuration are expected before the end of the decade (the European Space Agency (ESA), Soil Moisture and Ocean Salinity (SMOS) mission, and the National Aeronautics and Space Administration (NASA), Hydrospheric states "Hydros" mission). Though remote sensing can make spatially comprehensive measurements of surface soil moisture, it cannot provide information on the entire land surface hydrologic system, and the measurements represent only a snap shot in time. Alternatively, land surface hydrology process models may be used to predict the temporal ...
From view on Organization Behavior theory, the concept, development and affecting factors of safety culture are introduced. The focuses are on the establishment, development and management practice for safety culture at Daya Bay NPP. A strong safety culture, also demonstrated, has contributed greatly to improving performance at Daya Bay
Skip to Main Content Skip to Main Navigation National Highway Traffic Safety Administration Accessible menu--Sitemap Driving Safety Aggressive Driving Bicycles Child Safety...
Patient decision support systems have a promising role in the delivery of health care. However, the best approach for further development of these systems is a matter of speculation. To help chart a...Full Text Available
PURPOSE We wanted to assess the impact of an electronic health record–based diabetes clinical decision support system on control of hemoglobin A1c (glycated hemoglobin),...Full Text Available
Transcription factors drive organogenesis, from the initiation of cell fate decisions to the maintenance and implementation of these decisions. The Drosophila embryonic salivary gland...Full Text Available
At least implicitly, most clinical decisions represent an integration of disease and treatment-based risk assessments. Often, as is the case with acute coronary syndrome (ACS), these decisions need...Full Text Available
PURPOSE The Wells rule is widely used for clinical assessment of patients with suspected deep vein thrombosis (DVT), especially in the secondary care setting. Recently a new clinical decision...Full Text Available
Incorporation of clinical decision support (CDS) capabilities is required to realize the greatest benefits from computerized provider order entry (CPOE) systems. Discussions at a conference on CDS in...Full Text Available
The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the safety and reliability of the U.S. nuclear stockpile. The SSP uses past nuclear test data along with current and future nonnuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of current facilities and programs along with new experimental facilities and computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC)1 is a cornerstone of the SSP, providing simulation capabilities and computational resources to support the annual stockpile assessment and certification, to study advanced nuclear-weapons ...
This paper presents a decision approach, and associated computer software tools, for prioritizing and selecting among technology development activities. The approach elicits and then summarizes technology development preferences from stakeholders, and then integrates preferences into a set of funding recommendations. By formalizing the technology review process, the decision approach builds consensus and clarifies the basis for final budget decisions. The software development was conducted jointly by Pacific Northwest Laboratory and Decisions Science Associates, Incorporated. The Underground Storage Tank Integrated Demonstration funded the task; however, the approach should also be valuable to the US Department of Energy Office of Technology Development, the Office of Waste Management, and the Office of Environmental Restoration.
Ulrich in the forward to the Zenger and Folkman (2002) book, ''The Extraordinary Leader'', wrote about the importance of character in leadership stating, ''Everything about great leaders radiates from character. Character improves the probability of exhibiting strong interpersonal skill. Some of this perceived character is innate . . . but more is driven by the leader's self-awareness and interactions with others'' (p. ix). The purpose of this study was to explore the relationship between leadership effectiveness and character using leader-managers of knowledge workers as the subject sample. Findings indicated that character, particularly those factors associated with honesty, setting the example, and valuing and strengthening others, were what set the most effective leader-managers apart from their peers. Technical competence and self-efficacy were found to be common characteristics of the study sample as ...
The Joint Convention on the Safety of Spent Fuel management and on the Safety of Radioactive Waste Management is the first legal instrument to directly address the safety of spent fuel and radioactive waste management on a global scale. The Joint Convention entered into force in 2001. This paper describes its process and its main achievements to date. The perspectives to establish of a Global Waste Safety Regime based on the Joint Convention are also discussed. (authors)
This decision document presents the selected remedial action for the former Asarco Tacoma Smelter Facility and adjacent slag peninsula, in Ruston and Tacoma, Washington. This Record of Decision (ROD) describes the final cleanup remedy for soil, slag and surface water and disposal of hazardous soils, demolition debris, and residential soils. This ROD is intended to be an interim action for ground water.
Information technology plays an important role in medicine because of the advanced decision support systems (DSS) it can provide. We provide an overview of the building blocks necessary for a medical decision support system and introduce seven research articles in this special issue that describe the development and evaluation of individual medical DSS building blocks or complete medical DSS.
Nuclear Fuel Plant (FCN) is a facility that produces fuel bundles of CANDU-6 type for the CANDU nuclear power plant. Only natural and depleted uranium in bulk and itemized form are present as nuclear materials in this facility. Uranium and wastes from the plant are handled, processed, treated and stored throughout the entire facility. The nuclear materials with natural and depleted uranium are entirely under nuclear safeguards. The amount of uranium present in the plant in different forms and activities together with zircaloy, beryllium and other hazardous substances, wastes, explosive materials at high temperatures, etc. lead to special measures undertaken by Nuclear Safety Department (DNS) to ensure nuclear safety. Different aspects of safety are continuously monitored in the plant: operational safety, industrial safety, radiological safety, labour ...
The purpose of the Isotopes Facilities Deactivation Project (IFDP) is to place former isotopes production facilities at the Oak Ridge National Laboratory in a safe, stable, and environmentally sound condition; suitable for an extended period of minimum surveillance and maintenance (S&M) and as quickly and economical as possible. Implementation and completion of the deactivation project will further reduce the risks to the environment and to public safety and health. Furthermore, completion of the project will result in significant S&M cost savings in future years. The IFDP work plan defines the project schedule, the cost estimate, and the technical approach for the project. A companion document, the IFDP management plan, has been prepared to document the project objectives, define organizational relationships and responsibilities, and outline the management control systems to be employed in the management of the project. The project has adopted the strategy ...
The US investigated the use of {sup 233}U for weapons, reactors, and other purposes from the 1950s into the 1970s. Based on the results of these investigations, it was decided not to use {sup 233}U on a large scale. Most of the {sup 233}U-containing materials were placed in long-term storage. At the end of the cold war, the US initiated, as part of its arms control policies, a disposition program for excess fissile materials. Other programs were accelerated for disposal of radioactive wastes placed in storage during the cold war. Last, potential safety issues were identified related to the storage of some {sup 233}U-containing materials. Because of these changes, significant activities associated with {sup 233}U-containing materials are expected. This report is one of a series of reports to provide the technical bases for future decisions on how to manage this material. A basis for defining when {sup 233}U-containing materials can be managed as ...
In this paper a comparison between severe accident calculations performed for a WWER 1000 with the ASTEC1.1v0 and MELCOR 1.8.5 computer codes for a small break LOCA (ID 60 mm) without intervention of hydro accumulators is presented. This investigation has been performed in the framework of the SARNET project under the EURATOM 6th framework program. Once the accident sequence scenario is specified, both codes (MELCORE and ASTEC) are able to determine the core and containment damaged states, to estimate the release of radionuclides from the fuel as well as from the primary circuit and containment. Theses results are used to estimate the maximum period of the time during which the personnel could still take particular decisions in order to mitigate such an accident. The aim of the performed analysis is to estimate the discrepancy between ASTEC and MELCORE 1.8.5 calculations. Such discrepancies will be studied, if the case, proposal for ASTEC improvements will be made. ...
The process of ensuring the quality of computer codes can be very time consuming and expensive. The Oak Ridge National Laboratory (ORNL) Monte Carlo codes all predate the existence of quality assurance (QA) standards and configuration control. The number of person-years and the amount of money spent on code development make it impossible to adhere strictly to all the current requirements. At ORNL, the Nuclear Engineering Applications Section of the Computing Applications Division is responsible for the development, maintenance, and application of the Monte Carlo codes MORSE and KENO. The KENO code is used for doing criticality analyses; the MORSE code, which has two official versions, CGA and SGC, is used for radiation transport analyses. Because KENO and MORSE were very thoroughly checked out over the many years of extensive use both in the United States and in the international community, the existing codes were open-quotes baselined.close quotes This means that ...
Starting from the Molten Salt Breeder Reactor project of Oak-Ridge, we have performed parametric studies in terms of safety coefficients, reprocessing requirements and breeding capabilities. In the frame of this major re-evaluation of the molten salt reactor (MSR), we have developed a new concept called Molten Salt Fast Reactor or MSFR, based on the Thorium fuel cycle and a fast neutron spectrum. This concept has been selected for further studies by the MSR steering committee of the Generation IV International Forum in 2009. Our reactor's studies of the MSFR concept rely on numerical simulations making use of the MCNP neutron transport code coupled with a code for materials evolution which resolves the Bateman's equations giving the population of each nucleus inside each part of the reactor at each moment. Because of MSR's fundamental characteristics compared to classical solid-fuelled reactors, the classical Bateman equations have to be ...
Shut-off rod drive mechanism forms a safety critical system of a nuclear reactor. It is the space constraints for the given reactor layout, which makes design of shut-off rod drive mechanism (SRDM) a custom built design. Design of SRDM adopts fail-safe, replaceability and the simplicity criterion ensuring very high reliability of its operation. Shut-off rod drive mechanism for TAPP-3 and 4 and 'Critical Facility' have been recently designed and developed at Division of Remote Handling and Robotics (DRHR), BARC. These are designed with a number of advanced features and these are significantly different than those used in Dhruva and 220 MWe PHWRs. Design of SRDM is qualified through proto typing and life cycle testing on a full-scale test set-up. This paper gives details of qualification and life cycle test data for prototype SRDM for TAPP-3 and 4 and 'Critical Facility' and reliability assessment. (author)
One of the energy-saving devices used on gas cooking appliances to eliminate the standing pilot is a spark ignition system. For safety, an ignition system must start promptly and be active whenever flowing gas is not ignited. To minimize noise and nuisance shock hazard, ignition must occur quickly and the sparking must be stopped as soon as ignition occurs and remain off as long as the flame is present. To accomplish both of these requirements, ignition systems have been devised which use the electrical current rectification property of a flame to sense it. These systems spark whenever the gas valve is on and a flame is not present. The factors affecting the performance of a spark ignition system are numerous, complex, and transient. All of these properties make quantification of performance difficult. A system is described which can evaluate the overall performance of ignition systems over significant periods of time and varieties of operating ...
The core of Prismatic Modular Reactor (PMR) consists of assemblies of hexagonal graphite fuel and reflector elements. The core bypass flow of Very High Temperature Reactor (VHTR) is defined as the core flow that does not pass through the coolant channels but passes through the bypass gap between fuel elements. The increase in bypass flow makes the decrease in effective coolant flow. Since the core bypass flow has a negative impact on safety and efficiency of VHTR, core bypass phenomena have to be investigated to improve the core thermal margin of VHTR. For this purpose, the international project, I-NERI project, has been carried out since 2008. I-NERI project is collaborative project that KAERI and SNU of Korea side and INL, ANL and TAMU of U.S side are involved. In order to evaluate the core bypass flow, the multicolumn and multi-layer experimental facility is designed by SNU. In this experiment, the effect of cross-flow and local variation of ...
The inner part of a fusion reactor will have to operate at very high neutron loads. In steady-state reactors the minimum fluence before the scheduled replacement of the reactor core should be at least l0-15 Mw.yr/m2. A more frequent replacement of the core is hardly compatible with economic constraints. A most recent summary of the discussions of these issues is presented in Ref. [l]. If and when times come to build a commercial fusion reactor, the availability of information on the behavior of materials and components at such fluences will become mandatory for making a final decision. This makes it necessary an early development and construction of a neutron source for fusion material and component testing. In this paper, we present information on one very attractive concept of such a source: a source based on a so called Gas Dynamic Trap. This neutron source was proposed in the mid 1980s (Ref. [2]; ...
Development in Instrumentation and Control (I and C) technology provides more convenience and better performance, thus, adopted in many fields. To adopt newly developed technology, nuclear industry requires rigorous V and V procedure and tests to assure reliable operation. Adoption of digital system requires verification and testing of the OS for licensing. Commercial real-time operating system (RTOS) is targeted to apply to various, unpredictable needs, which makes it difficult to verify. For this reason, simple, application-oriented realtime OS is developed for the nuclear application. In this work, we show how to verify the developed RTOS at each development lifecycle. Commercial formal tool is used in specification and verification of the system. Based on the developed model, software in C language is automatically generated. Tests are performed for two purposes; one is to identify consistency between the verified model and the generated code, the other is to ...
Development in Instrumentation and Control (I and C) technology provides more convenience and better performance, thus, adopted in many fields. To adopt newly developed technology, nuclear industry requires rigorous V and V procedure and tests to assure reliable operation. Adoption of digital system requires verification and testing of the OS for licensing. Commercial real-time operating system (RTOS) is targeted to apply to various, unpredictable needs, which makes it difficult to verify. For this reason, simple, application-oriented realtime OS is developed for the nuclear application. In this work, we show how to verify the developed RTOS at each development lifecycle. Commercial formal tool is used in specification and verification of the system. Based on the developed model, software in C language is automatically generated. Tests are performed for two purposes; one is to identify consistency between the verified model and the generated code, the other is to ...
This book proposed that a post-2012 climate regime will need to balance the needs of all countries while aiming to prevent the potentially serious economic and social consequences of the impacts of climate change. Four elements were presented to support the emergence of an internationally acceptable approach: (1) the need to ensure sustainable economic development; (2) the effective development and penetration of clean technologies; (3) the establishment of an effective international carbon market over the long term; and (4) the integration of adaptation in development and natural resource management decision-making. A series of discussion papers were presented which reviewed options on how best to create an effective and inclusive international climate regime that will achieve large reductions in global emissions and equitably reflect the diverse circumstances of countries while promoting sustainable economic development. The first paper highlighted some of the ...
The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of waste tourism, the general welfare of the public; regulations on waste management, governmental means of monitoring waste management: Obligations to dispose of waste, compulsory ...
Aim: To determine whether experience improves the consistency of visual search behaviour in fracture identification in plain radiographs, and the effect of specialization. Material and methods: Twenty-five observers consisting of consultant radiologists, consultant orthopaedic surgeons, orthopaedic specialist registrars, orthopaedic senior house officers, and accident and emergency senior house officers examined 33 skeletal radiographs (shoulder, hand, and knee). Eye movement data were collected using a Tobii 1750 eye tracker with levels of diagnostic confidence collected simultaneously. Kullback-Leibler (KL) divergence and Gaussian mixture model fitting of fixation distance-to-fracture were used to calculate the consistency and the relationship between discovery and reflective visual search phases among different observer groups. Results: Total time spent studying the radiograph was not significantly different between the groups. However, the expert groups had a higher number of true ...
Hybrid models for solving unit commitment problem have been proposed in this paper. To incorporate the changes due to the addition of new constraints automatically, an expert system (ES) has been proposed. The ES combines both schedules of units to be committed based on any classical or traditional algorithms and the knowledge of experienced power system operators. A solution database, i.e. information contained in the previous schedule is used to facilitate the current solution process. The proposed ES receives the input, i.e. the unit commitment solutions from a fuzzy-neural network. The unit commitment solutions from the artificial neural network cannot offer good performance if the load patterns are dissimilar to those of the trained data. Hence, the load demands, i.e. the input to the fuzzy-neural network is considered as fuzzy variables. To take into account the uncertainty in load demands, a fuzzy decisionmaking approach has also been ...
ICU telemedicine uses audiovisual conferencing technology to provide critical care from a remote location. Research is needed to best define the optimal use of ICU telemedicine, but efforts are hindered by methodological challenges and the lack of an organized delivery approach. We convened an interdisciplinary working group to develop a research agenda in ICU telemedicine, addressing both methodological and knowledge gaps in the field. To best inform clinical decision-making and health policy, future research should be organized around a conceptual framework that enables consistent descriptions of both the study setting and the telemedicine intervention. The framework should include standardized methods for assessing the preimplementation ICU environment and describing the telemedicine program. This framework will facilitate comparisons across studies and improve generalizability by permitting context-specific interpretation. Research based on this framework ...
The research project's objective is to create a decision help for owners of residential buildings for several families regarding the renewal of decentralized heating and warm water preparation systems in the flats. The focus lies on a comparison of the costs of typical systems on the basis of a full cost calculation. This is done by taking into consideration the intentions of residential building companies like the reduction of additional costs to be paid by the tenants (both for social reasons and to make the flats easier to rent), low investment costs, low maintenance costs, energy saving, tenants' claims for comfort and acceptance by the tenants, economical reasons, especially regarding flats fully amortized (activation in the balance sheet). In addition to the quantitative comparison, the advantages and disadvantages of the different systems were also compared to one another from the qualitative point of view. [German] ...
The Georges Bank, off southwestern Nova Scotia, is one of the most biologically productive continental shelf ecosystems in the world. It supports a wide diversity of species, including many seabirds. In 1988, federal and provincial legislation placed a moratorium on petroleum exploration and drilling on the Georges Bank, directing the ministers of Natural Resources Canada, and of the Nova Scotia Department of Natural Resources to make a decision regarding the moratorium by January 1, 2000. This report by the Ecology Action Centre (EAC) asks the Georges Bank Review Panel to recommend extending the moratorium on Georges Bank and adjacent areas until 2012, in part to match the American moratorium. Other reasons why the panel made this recommendation were explored. The principal reason is the EAC concern that when the moratorium is lifted, several oil and gas developments will proceed in this ecologically significant offshore area that could result ...
The report presents an integrated software system developed at the Norwegian Electric Power Research Institute (EFI), for production scheduling, maintenance handling, network security analysis, inflow forecasting, and load forecasting. The integrated software is being developed with focus on hydro-dominated power supply systems. In specific terms it is expected that application of the software will improve the operational decisions, and make the planning process more effective. The optimal scheduling of hydro resources poses severe computational problems in system operations planning. This necessitates problem decomposition. In the EFI approach, planning is split into three main levels: long-term, mid-term and short-term planning. The long-term planning aims at evaluating the seasonal and pluriannual handling of regional storages in view of firm power supply obligations, inflow statistics, main hydraulic and electric transit limitations, and ...
This report provides information to government and industry to enable decision-making and management of local environmental quality conditions. The need for a summary air quality report has arisen in recent years due to growing concerns about air quality. Increased growth in population and the tourism industry is placing additional pressures on environmental quality. The report summarized meteorological and air quality data collected by the British Columbia Ministry of Water, Land and Air Protection in the Sea-to-Sky airshed from 1984 to 2001. The airshed is located in the Lower Mainland region of British Columbia. Air quality monitoring was conducted for various periods at 18 different stations and meteorological monitoring was conducted at 4 locations. A list of both provincial and national air quality objectives and standards was provided, with definitions and reference levels from the Canadian Environmental Protection Act. Meteorological data was presented on a ...
Oestfold Research has trough the project 'Climate accounts for disposal' for Waste Norway developed a model for calculation of net greenhouse gas emissions at the disposal of various waste types. The model is based on life cycle methodology according to the standard IS014044. This model has been used for plastic packaging in the project by adapting the basic values of specific conditions in the municipality of Fredrikstad. Oestfold Research has made an assessment of greenhouse gas emissions for the recycling and material recovery of plastic packaging from households in the district on assignment from Fredrikstad municipality and compared with the current solution where plastic packaging together with residual waste is used for energy utilisation. Based on the population in Fredrikstad and estimated amount of plastic packaging waste arising per household per year the difference in climate impact was analyzed and these scenarios calculated: Introduction of recycling and ...
A graphic approach, terms a Genetic Activity Profile (GAP), was developed to display a matrix of data on the genetic and related effects of selected chemical agents. The profiles provide a visual overview of the quantitative (doses) and qualitative (test results) data for each chemical. Either the lowest effective dose or highest ineffective dose is recorded for each agent and bioassay. Up to 200 different test systems are represented across the GAP. Bioassay systems are organized according to the phylogeny of the test organisms and the end points of genetic activity. The methodology for producing and evaluating genetic activity profile was developed in collaboration with the International Agency for Research on Cancer (IARC). Data on individual chemicals were compiles by IARC and by the US Environmental Protection Agency (EPA). Data are available on 343 compounds selected from volumes 1-53 of the IARC Monographs and on 115 compounds identified as Superfund Priority Substances. ...
The decision of the United Kingdom to adopt a policy of solidification of high level waste had led to renewed interest in vitrification. The HARVEST process chosen is an adaptation of the FINGAL concept developed at Harwell 15 years ago. Because of certain changes in engineering design and differences in the composition of the waste, additional chemical engineering data are required for HARVEST. The new inactive pilot plant has been built to provide this information. Its size is virtually full-scale and batches of glass up to 1 tonne can be manufactured in vessels of diameter up to 750mm. Five glass-making runs have been carried out. Attention has concentrated on the performance of the off-gas system which employs wet methods. Carry-over of solids occurs, primarily as a result of physical entrainment. The carry-over of synthetic fission products is improved from 2.5 to 0.1% by directing the feed down the vessel walls. Most of the entrained ...
PETROBRAS/TRANSPETRO Pipelines and Terminals have 500 regular employees and 5.064 out sourced workers in its Southeast Division. The out sourced employees work under 125 contracts involving a wide range of activities such as maintenance, pipeline operation, pipeline launching, engineering, administrative and auxiliary services. Among these workers, 1.200 peoples are subjected to occupational exposure, which may be present in the industrial process or in the products transported in our pipelines, e.g. industrial noise, sulfidric gas, toluene, xylene and benzene (recognized as a carcinogen according to ACGIH and Brazilian Ministry of Labour). Our PPRA (acronym in Portuguese for Occupational Exposure Prevention Program) involves the workforce and fosters health by anticipation, recognition, evaluation and control of the situations that may result in injuries. Further actions include the procurement of equipment for detection of these agents not only in the air but also diluted in liquids ...
The overall goal of the DOE fine particulate program is to ensure that the best science and technology is available for any regulatory decision-making related to the health and environmental impacts of ambient fine particulate matter and regional haze. Interest primarily lies in the particulate fraction having aerodynamic diameters of 2.5 microns and less (PM2.5). Particulates of this size are the focus of the newly established National Ambient Air Quality Standards. As such, the Federal Energy Technology Center (FETC) is establishing a fine particulate sampling station at the Center's Pittsburgh site located in South Park Township, PA. This sampling station is one of a group of stations scattered throughout Pennsylvania, West Virginia, and Ohio that constitute the Upper Ohio River Valley Project. The station is equipped with a full complement of fine particulate and gaseous monitors including the following: (1) R and P Sequential FRM sampler, (2) Grimm ...
This paper presents a technical feasibility study project for the large scale rooftop photovoltaics (PV) grid connected system at Charoenphol-Rama I green building super store of TESCO LOTUS (TL) in Thailand. The objective of this project is (i) to study the technical feasibility of installation 350 kWp PV systems on the top of the roof in this site (ii) and to determine the energy produce from this system. The technical factors are examined using a computerized PVS 2000 simulation and assessment tool. This super store building located in Bangkok, with latitude 14 N, longitude 100 E and the building direction is 16 from North direction. The building roof area is 14,000 m2; with 3 degree face East and 3 degree face West pitch. Average daily solar energy in this area is approximately 5.0 kWh. The study team for this project consists of educational institution as School of Renewable Energy Technology (SERT) and private institution as Panya Consultants (PC). TL is the project owner, PC is ...
In France, groundwater usage represents 40 per cent of volumetric use, outside of thermal power plants. Groundwater represents 60 per cent of domestic and public use, 40 per cent in the industrial sector, and is increasing in the agricultural sector where it accounts for 20 per cent. Groundwater withdrawal in France has slightly increased over the last twenty years and benefited the agricultural sector. Availability throughout the territory, the consistency of resupply and natural quality has rendered groundwater a prevailing source for drinking water. Water protection and management is important and led to the adoption of legislative and regulatory measures. The Mining Code (Code minier) allows for exploitation of underground resources starting at 10 metres. The Rural Code (Code rural) mandates the declaration of public utility for water collection for the public. Protection areas are to be provided under the Public Health Code (Code de sante publique). Proper permits and ...
The US Department of Energy (DOE) is preparing to perform significant remediation activities of the sites for which it is responsible. To accomplish this, it is preparing a corporate global plan focused on activities over the next decade. Significant in these planned activities is the transportation of the waste arising from the remediation. The costs of this transportation are expected to be large. To support the initial assessment of the plan, a cost estimating model was developed, peer-reviewed against other available packaging and transportation cost data, and applied to a significant number of shipping campaigns of radioactive waste. This cost estimating model, known as the Ten-year Plan Transportation Cost Model (TEPTRAM), can be used to model radioactive material shipments between DOE sites or from DOE sites to non-DOE destinations. The model considers the costs for (a) recovering and processing of the wastes, (b)packaging the wastes for transport, and (c) the carriage of the ...
This paper gives a brief review about the state of knowledge on the distributional aspects of climate change impacts. The paper is largely limited to the distribution of impacts between countries (in Section 2). Although there are virtually no estimates reported in the literature, the distribution of impacts within countries is also important. Impact estimates for different sectors (agriculture, health, sea level rise) provides little guidance for estimating differential impacts within countries. It is even harder to find estimates based on social classes. The paper restricts itself to equity about the consequences of climate change. Equity issues about the consequences of emission reduction are ignored here, but should of course be part of a policy analysis. Equity issues about procedures for decisionmaking are also ignored. The paper is organised as follows. Section 2 reviews recent estimates of the regional impacts of climate change. ...
"1"8F-fluorodeoxyglucose (FDG) uptake on positron emission tomography (PET) scan has been found to reflect tumor aggressiveness and prognosis in various types of cancer. However, pattern of FDG uptake in biliary malignancies and its clinical significance have not been studied well. The purpose of this study was to assess the additional value of "1"8F-FDG PET in differential diagnosis and prognosis of cholangiocarcinoma (CC) according to the tumor location and tumor morphology. From April 2005 to May 2008, eighty two patients (M:F=55:27, age 66.2#+-#9.6 yrs) with CC underwent "1"8F-FDG PET. For semiquantitative analysis, the maximum standardized uptake value (SUV_m_a_x) was obtained from the primary tumor. The difference of SUV_m_a_x according to the tumor location and tumor growth pattern, such as scirrhous type, nodular type, polypoid type were compared. Overall sensitivity of PET scan was 81.7% in CC. SUV_m_a_x on PET scan in intrahepatic CC was significantly higher compared to ...
Large-scale field tracer experiments have been conducted on Ulchin, Wolsung and Daeduk sites for the purpose of validating FADAS and of analyzing the environmental characteristics around the nuclear sites. The most influential factor in atmospheric dispersion is the meteorological condition. During the experiment, meteorological data were measured on the release point and the selected positions among sampling points. Once radioactive materials are released to the atmosphere, members of public may be exposed through the environmental media such as air, soil and foods. Therefore, to protect the public, adequate countermeasures should be taken at due time for those exposure pathways. both processes, of justification and optimization are applied to a countermeasure simultaneously for decision-making. The work scope of Biological research for the radiation protection had contained the search of biological microanalytic methods for assessing the health effect by ...
Asymptomatic cholelithiasis is increasingly diagnosed today, mainly as a result of the widespread use of abdominal ultrasonography for the evaluation of patients for unrelated or vague abdominal complaints. About 10-20% of people in most western countries have gallstones, and among them 50-70% are asymptomatic at the time of diagnosis. Asymptomatic gallstone disease has a benign natural course; the progression of asymptomatic to symptomatic disease is relatively low, ranging from 10-25%. The majority of patients rarely develop gallstone-related complications without first having at least one episode of biliary pain ("colic"). In the prelaparoscopy era, (open) cholecystectomy was generally performed for symptomatic disease. The minimally invasive laparoscopic cholecystectomy refueled the discussion about the optimal management of asymptomatic cholelithiasis. Despite some controversy, most authors agree that the vast majority of subjects should be managed by observation alone (expectant ...
The most important factor in assessing radiologic risk is ensuring scientific means for evaluation of the radioactive release impact upon humans and organisms. To evaluate quantitatively this impact not only knowledge of radioactivity distribution in these dynamical systems is necessary but also understanding the transfer mechanisms between ecosystem components is needed. Thus a complete radioecologic study appear to be very complex and needs defining the source term, dynamic description of radionuclides behavior in the ecosystem, estimation of radiation doses in the major components of the ecosystem and finally the effects of radiation doses upon different parts of the systems. A diagram of the steps implied in evaluation of the effects due to radioactive effluent release in the environment is presented and discussed. The following steps are described: - identification of radioactive sources, as well as their input rate. Presence of noxious materials such as heavy metals or some ...
A relational database capable of storing and manipulating the large volumes of data on air toxic metals has been developed for the Center for Air Toxic Metals at the Energy and Environmental Research Center (EERC) of the University of North Dakota. The database provides information to researchers, managers, and operations personnel to aid in their decisionmaking and long-term planning of issues related to air toxic metals. A personal computer-based graphical user interface is used to access the data located on a UNIX workstation at the EERC. With security codes and software issued by the EERC and an Internet service provider in place, the database can be accessed externally through the Internet. Currently the database contains over 3000 analytical measurements from nine full-scale systems and several bench-scale operations. Data are available on gas, solid, and liquid stream samples as well as relevant engineering parameters, including process ...
Like other Central European countries, Poland faces the twin challenges of improving environmental quality while also fostering sustainable economic development. In this study we examine the costs of different standards for air pollution control, and the cost savings from using incentive-based policy instruments in lieu of more rigid command-and-control policies. The comparisons are based on the results of a simulation model of energy use and air pollution control for the Polish economy over 1990-2015. The model simulates least-cost energy supply decisions under different environmental policy assumptions, the corresponding emissions, and the cost of achieving the specified policy objectives. The model results suggest that incentive-based policies will have efficiency gains over command policies that are at least worthy of consideration and may be quite substantial. The size of the gains in practice depends in part on how much flexibility is built into the command ...
Full text: Research reactors have been playing a multi dimensional role in areas of nuclear fuel cycle programme, radio-isotope productions, neutron beam research etc. To ensure an efficient, smooth and safe operation of a nuclear research reactor, many reactor physics evaluations are required on routine basis. As part of reactor core management the important activities are maintaining core reactivity status, core power distribution, xenon estimations, safety evaluation of in-pile irradiation samples and experimental assemblies and assessment of nuclear safety in fuel handling/storage. In-pile irradiation requires a prior estimation of the reactivity load due to the sample, heating rate and the activity developed in it during irradiation. For the safety of the personnel handling irradiated samples the dose rate at the surface of shielded flask housing the irradiated sample should be less than 200 mR/Hr. Therefore, a proper ...
The Self Actuated Shutdown System (SASS) is now under development for use in a large scale FBR, in order to establish the passive shutdown capability against the postulated ATWS events, i.e. ULOF, UTOP and ULOHS. The function of SASS makes use of the safety characteristics of a liquid metal cooled FBRs such as a large subcooling and low pressure system. The insertion of the control rods insertion is assured even in the most conservative seismic design condition by employing articulate rods and the SASS will be installed into the detaching mechanism employing a curie point the magnet alloy. ULOF analysis of the present FBR shows that coolant boiling inception is prevented if a control rod of the SASS is detached at the uppermost temperature of 680degC for the Curie point magnet, and after the reactor shutdown the coolant temperature is kept below 600degC by the pony motor flow. Therefore the SASS will establish passive shutdown capability ...
The PDIM multifunction regulator offers in one single unit the basic functions filtering, slamshut safety valve, pressure reduction and a gas flow straightening vane. This concept formulated by the engineer J.-P. Cornil is a Gaz de France patent. Developed and manufactured by a French industrial company it incorporates some astute innovations in the field of fluid dynamics. Its technical caracteristics make a significant step forward in gas technology. Since the first unit was brought into service over 1000 PDIM units have been built and incorporated in gas regulating and metering stations for transport, distribution and industrial applications. The very compact nature of the PDIM enhanced by its direct bolting to a turbine or other type of gas meter leads to small size stations allowing lower cost projects and making it easier to set in populated or architecturally significant areas. (orig.) [Deutsch] Der PDIM ist eine ...
The Fixed Bed Nuclear Reactor (FBNR) is a small 40 MWe reactor based on the Pressurized Water Reactor (PWR) technology. FBNR is an integrated primary circuit and simple in design. It has the characteristics of being small, modular, proliferation resistant, inherently safe and passively cooled reactor with reduced adverse environmental impact. It utilizes the fuel designed for high temperature reactors operating in a relatively low temperature of PWR environment The 15 mm diameter spherical fuel elements are made of TRISO type microspheres embedded in graphite and cladded by SiC. The coolant flow transfers them from the fuel chamber into the core and become fixed forming a suspended core. Any accident signal will cut off the power to the coolant pump causing a stop in the flow. This results in making the fuel elements fall out of the reactor core by the force of gravity and return into the fuel chamber where they are passively cooled under subcritical condition. ...
The use of standard cementitious material creates pulses of pH in the magnitude of 12-13 in the leachates and release alkalis. Such a high pH is detrimental and also unnecessarily complicates the safety analysis of the repository. As no reliable pH-plume models exist, the use of products giving a pH below 11 in the leachates facilitates the safety analysis. Also, according to current understanding, the use of low-pH cement (pH = 11) will not disturb the functioning of the bentonite, although limiting the amount of low-pH cement is recommended. A result of the project is that there are both low-pH cementitious material for grouting larger fractures (= 100 {mu}m) and non-cementitious material for grouting smaller fractures (< 100 {mu}m) that will, after further optimisation work, be recommended for grouting of deep repositories. This project concentrated on the technical development of properties for the low pH grouts. Long-term ...
Safety indicators play a role in providing information on organizational performance, motivating people to work on safety and increasing organizational potential for safety. The aim of this report is to provide an overview on leading safety indicators in the domain of nuclear safety. The report explains the distinction between lead and lag indicators and proposes a framework of three types of safety performance indicators - feedback, monitor and drive indicators. Finally the report provides guidance for nuclear energy organizations for selecting and interpreting safety indicators. It proposes the use of safety culture as a leading safety performance indicator and offers an example list of potential indicators in all three categories. The report concludes that monitor and drive indicators are so ...
This report describes the results obtained during Stage 13 of a long-term research and development program concerning the development of diagnostics and monitoring methods for nuclear reactors. A brief proposal for the continuation of this program in Stage 14 is also given at the end of the report. The program executed in Stage 13 consists of three parts and the work performed in each part is summarized below. 1. Study of criticality, neutron kinetics and neutron noise in molten salt reactors (MSR). Although the original goal of the investigations of the MSR in Stage 13 was to calculate the neutron noise induced by the fluctuations of the fuel temperature, the study, solution and interpretation of the static problem, as well as to define an approximate version of the point kinetic approximation was necessary to perform. As it turned out, these tasks in themselves were more involved, and also very edifying, to solve. Hence, in this report, we confine the study of the reactor physics of ...
This report presents a study on the use of computerised, continuous remote monitoring systems for fire and explosive atmosphere safety in underground coal mines. The effects of these systems on the safety level in mines are investigated, and the relationship between mine safety regulations and computerised, continuous, remote monitoring is analysed.
Data mining is a useful decision support technique that can be used to discover production rules in warehouses or corporate data. Data mining research has made much effort to apply various mining algorithms efficiently on large databases. However, a serious problem in their practical application is the long processing time of such algorithms. Nowadays, one of the key challenges is to integrate data mining methods within the framework of traditional database systems. Indeed, such implementations can take advantage of the efficiency provided by SQL engines. In this paper, we propose an integrating approach for decision trees within a classical database system. In other words, we try to discover knowledge from relational databases, in the form of production rules, via a procedure embedding SQL queries. The obtained decision tree is defined by successive, related relational views. Each view corresponds to a given population in ...
National Nuclear Safety Department is authorized by Infra (Iranian Nuclear Regulatory Authority) for issuing rules and regulation and conducting the licensing and supervisory process for nuclear facilities. The main responsibilities of the NNSD are conducted via five main division are, nuclear codes and standards, Nuclear Safety assessment, Authorization, Inspection and Enforcement and Technical Support. In this paper, the functions and responsibilities of TSD in enhancing nuclear safety are described. Examples of main tasks to support the Nuclear Safety assessment division regarding to technical calculations and research of safety issues in licensing documents are provided. (author)
Program decisions by symphony orchestra management are influenced by various factors. To examine these factors, we create an objective index of the propensity of a symphony orchestra to perform the standard repertoire. We use regression analysis to examine factors that influence programming decisions of 64 US symphony orchestras in 2006?2007, including public and private sources of funding. We find that increased funding from ticket sales, endowments, and local government increases the likelihood that an orchestra will perform nonstandard repertoire. In addition, the results suggest that a symphony orchestra?s music director does not have a significant impact on the degree of program conventionality.
This report reviews system safety analysis methods and examines their application to nuclear waste management systems. The safety analysis methods examined include expert opinion, maximum credible accident approach, design basis accidents approach, hazard indices, preliminary hazards analysis, failure modes and effects analysis, fault trees, event trees, cause-consequence diagrams, G0 methodology, Markov modeling, and a general category of consequence analysis models. Previous and ongoing studies on the safety of waste management systems are discussed along with their limitations and potential improvements. The major safety methods and waste management safety related studies are surveyed. This survey provides information on what safety methods are available, what waste management safety areas have been analyzed, and what are potential areas ...
familiarity fire triangle (i.e., fuel, oxidant, and ignition source) are excluded. It Is obvious that for the baseline safety goal for spacecraft this ...
The management of risks of explosives are described. Administrative and procedural controls are considered. The safety management plan involves hazard identification, risk analysis, assessment and control. The current position of explosives safety is considered. 4 tabs.
Recommendations of the Advisory Committee on Reactor Safeguards are presented to the Commissioners for their consideration for FY 82 budget for the NRC safety research program.
Recommendations of the Advisory Committee on Reactor Safeguards are presented to the Commissioners for their consideration for FY 83 budget for the NRC safety research program.
AECL Publications on Reactor Safety in CANDU Reactors are listed in this bibliography. The listing is chronological and the accompanying index is by subject. The bibliography will be brought up to date annually. (auth).
BACKGROUNDColorectal cancer (CRC) screening can be administered through tests with varied characteristics and is a preference-sensitive decision.OBJECTIVETo...Full Text Available
2.1.1 Stochastic decision and control approaches .... 14. 2.1.2 Queueing theory ...... Infoton Vistar/2 terminal keyboard) is used by the pilot for ...
OBJECTIVE: New surgical procedures designed to assist in the treatment of peritoneal surface malignancy were sought. BACKGROUND: Decisions regarding the treatment of cancer depend on the anatomic location...Full Text Available
... Environmental Assessment of Proposed Effluent Limitations Guidelines and Standards for the Meat and Poultry Industry Point Source; EPA-821-B-01-008; US ...
Phytoremediation, a technology using plants to remediate or stabilize contaminants in soil, groundwater, or sediments, has recently received a great deal of attention from regulators, consultants, responsible parties, and stakeholders. phytoremediation ha...
for cyber issues? Did you decide to establish this position because of the WikiLeaks incident? DR. SLAUGHTER: No. No, that decision was actually taken nearly a year ago,...
BackgroundThe permeabilization of mitochondrial membranes is a decisive event in apoptosis or necrosis culminating in cell death. One fundamental mechanism by which...Full Text Available
Significant environmental issues and regulatory proceedings in Alberta were discussed. The Mackenzie Valley Pipeline Project was reviewed in relation to the Deh Cho First Nation's advanced actions in the federal court to enjoin the review panel from proceeding with the review process. The Deh Cho First Nation is seeking a declaration that the plan violates their rights under the Canadian Charter of Rights and Freedoms and the Constitution Act. Various regulatory and government agencies have now developed a plan to coordinate their different regulatory processes and approvals in the Cooperation Plan for the Environmental Impact Assessment and Regulatory Review of the Northern Gas Pipeline project. The Deh Cho allege that they were not afforded the opportunity to participate in the development and implementation of the plan. A review panel plans to proceed once the environmental and social impacts are determined, and the consortiums plan to minimize harm has been submitted. ...
The Stockpile Stewardship Program (SSP) is a single, highly integrated technical program for maintaining the surety and reliability of the U.S. nuclear stockpile. The SSP uses past nuclear test data along with current and future non-nuclear test data, computational modeling and simulation, and experimental facilities to advance understanding of nuclear weapons. It includes stockpile surveillance, experimental research, development and engineering (D&E) programs, and an appropriately scaled production capability to support stockpile requirements. This integrated national program requires the continued use of current facilities and programs along with new experimental facilities and computational enhancements to support these programs. The Advanced Simulation and Computing Program (ASC) is a cornerstone of the SSP, providing simulation capabilities and computational resources to support the annual stockpile assessment and certification, to study advanced nuclear weapons design ...
In this paper, we put forward a systematic method to analyze, control and evaluate the safety issues of medical robotics. We created a safety model that consists of three axes to analyze safety factors. Software and hardware are the two material axes. The third axis is the policy that controls all phases of design, production, testing and application of the robot system. The policy was defined as hazard identification and safety insurance control (HISIC) that includes seven principles: definitions and requirements, hazard identification, safety insurance control, safety critical limits, monitoring and control, verification and validation, system log and documentation. HISIC was implemented in the development of a robot for urological applications that was known as URObot. The URObot is a universal robot with different modules adaptable for 3D ultrasound ...
Several nuclear power plant sites have been wounded in the crossfire between two distinct corporate cultures. The traditional utility culture lies on one side and that of the nuclear navy on the other. The two corporate cultures lead to different perceptions of open-quotes safety culture.close quotes This clash of safety cultures obscures a very important point about nuclear plant operations: Safety depends on organizational learning. Organizational learning provides the foundation for a perception of safety culture that transcends the conflict between utility and nuclear navy cultures. Corporate culture may be defined as the knowledge, attitudes, and beliefs shared by employees of a given company. Safety culture is the part of corporate culture concerning shared attitudes and beliefs affecting individual or public safety. If the safety ...
As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress corrosion cracking susceptibility. The effects of lead contamination on the stress corrosion cracking ...
This is the first of a series of monthly reports summarizing the status of the work of the National Accelerator Laboratory. This first report will cover developments since the publication of the Design Report in January. Authorization hearings were held before the Joint Committee on Atomic Energy on February 21, 1968. Dr. Wilson described the plans and designs of the Laboratory. The present plan of the Laboratory is that the Village of Weston will be utilized for office, laboratory, and shop space during construction. The Laboratory business office is already occupying several houses. The linac section is occupying three houses for offices and construction of an 8,000 sq ft laboratory building for linac work is almost complete. Another house is being used and a 4,500 sq ft inflatable building is being constructed for model-magnet and vacuum testing. Other temporary buildings will be constructed for use by other sections. We plan to move into the village as rapidly as is feasible and it ...
Combined heat and power (CHP) or cogeneration is the sequential production of two forms of useful energy from a single fuel source. In most CHP applications, chemical energy in fuel is converted to both mechanical and thermal energy. The mechanical energy is generally used to generate electricity, while the thermal energy or heat is used to produce steam, hot water, or hot air. Depending on the application, CHP is referred to by various names including Building Cooling, Heating, and Power (BCHP); Cooling, Heating, and Power for Buildings (CHPB); Combined Cooling, Heating, and Power (CCHP); Integrated Energy Systems (IES), or Distributed Energy Resources (DER). The principal technical advantage of a CHP system is its ability to extract more useful energy from fuel compared to traditional energy systems such as conventional power plants that only generate electricity and industrial boiler systems that only produce steam or hot water for process applications. By using fuel energy for both ...
As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress corrosion cracking susceptibility. The effects of lead contamination on the stress corrosion cracking ...
As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress corrosion cracking susceptibility. The effects of lead contamination on the stress corrosion cracking ...
Current methods to calculate dose distributions with organ motion can be broadly classified as 'dose convolution' and 'fluence convolution' methods. In the former, a static dose distribution is convolved with the probability distribution function (PDF) that characterizes the motion. However, artifacts are produced near the surface and around inhomogeneities because the method assumes shift invariance. Fluence convolution avoids these artifacts by convolving the PDF with the incident fluence instead of the patient dose. In this paper we present an alternative method that improves the accuracy, generality as well as the speed of dose calculation with organ motion. The algorithm starts by sampling an isocenter point from a parametrically defined space curve corresponding to the patient-specific motion trajectory. Then a photon is sampled in the linac head and propagated through the three-dimensional (3-D) collimator structure corresponding to a particular MLC segment chosen randomly from ...
Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.
Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.
Abstract Overall Numbers Small, But Study Finds SSRI Exposure, Autism Link Additional Drug Safety, Efficacy Data Needed for Pediatric Bipolar Disorder SGA Safety and Efficacy in Children and Adolescents Aripiprazole Safety and Tolerability for Irritability in Autism No Lisdexamfetamine Effect on Sleep Disturbances in Children With ADHD Sickle Cell Disease With Comorbid Depression Homeopathy in Psychiatry Manic Symptoms Induced by Marijuana in a Healthy Adolescent New Warnings Safety Labeling Changes
U.S. Department of Energy (DOE) Policy 450.4, Safety Management System Policy commits to institutionalizing an Integrated Safety Management System (ISMS) throughout the DOE complex as a means of accomplishing its missions safely. DOE Acquisition Regulation 970.5204-2 requires that contractors manage and perform work in accordance with a documented safety management system.
The Fast Flux Test Facility (FFTF) will provide a prototypic test environment for advanced fuels and materials development within the U. S. LMFBR program. As a fast test reactor, the FFTF also provides a potentially unique capability for conduct of safety experimentation relevant to selected LMFBR safety issues associated with postulated core disruption events. The utility and feasibility of possible extension of FFTF testing into the area of safety research is being investigated. 5 fig.
This paper will review code and standard and the safety related features of major components of Monju: Components of the Reactor Coolant Boundary; Components of the Reactor Shurdown Systems; Components of the Decay Heat Removal Systems; Components of the Engineered Safety Features; Other Safety Related Components. Their relationship to the system or plant function is emphasized, in reviewing these components.
The Technical Safety Requirements (TSRs) for the Cold Vacuum Drying Facility define acceptable conditions, safe boundaries, bases thereof, and management or administrative controls required to ensure safe operation. Controls required for public safety, significant defense-in-depth, significant worker safety, and for maintaining radiological and toxicological consequences below risk evaluation guidelines are included.
The main purpose of this report is to document the benchmarking results and verification of the RESRAD-OFFSITE code as part of the quality assurance requirements of the RESRAD development program. This documentation will enable the U.S. Department of Energy (DOE) and its contractors, and the U.S. Nuclear Regulatory Commission (NRC) and its licensees and other stakeholders to use the quality-assured version of the code to perform dose analysis in a risk-informed and technically defensible manner to demonstrate compliance with the NRC's License Termination Rule, Title 10, Part 20, Subpart E, of the Code of Federal Regulations (10 CFR Part 20, Subpart E); DOE's 10 CFR Part 834, Order 5400.5, ''Radiation Protection of the Public and the Environment''; and other Federal and State regulatory requirements as appropriate. The other purpose of this report is to document the differences and similarities between the RESRAD (onsite) and ...
The possibility of developing reactor designs with inherent safety characteristics sufficient to provide walk away safety is receiving additional emphasis in the LMR program. A key element in this effort is the recognition that LMR's possess safety characteristics above and beyond those employed in past safety review processes. Some of these additional safety characteristics are due to reactivity feedback effects caused by small structural movements during hypothetical severe design transients. The effects of these characteristics upon the behavior of the FFTF under such transients has been assessed and is discussed in this paper. The paper also presents a preliminary test matrix which might allow experimental verification of the structural reactivity feedback effects. Such experimental verification should be very useful to innovative designers seeking to optimize inherent ...
The possibility of developing reactor designs with inherent safety characteristics sufficient to provide ''walk away'' safety is receiving additional emphasis in the LMR program. A key element in this effort is the recognition that LMR's possess safety characteristics above and beyond those employed in past safety review processes. Some of these additional safety characteristics are due to reactivity feedback effects caused by small structural movements during hypothetical severe design transients. The effect of these characteristics upon the behavior of the FFTF under such transients has been assessed and is discussed in this paper. The paper also presents a preliminary test matrix which might allow experimental verification of the structural reactivity feedback effects. Such experimental verification should be very useful to innovative designers seeking to optimize inherent ...
This Safety Analysis Report (SAR) is prepared in compliance with the requirements of DOE Order 5480.23, Nuclear Safety Analysis Reports, and has been written to the format and content guide of DOE-STD-3009-94 Preparation Guide for U. S. Department of Energy Nonreactor Nuclear Safety Analysis Reports. The Hot Cell Facility is a Hazard Category 2 nonreactor nuclear facility, and is operated by Sandia National Laboratories for the Department of Energy. This SAR provides a description of the HCF and its operations, an assessment of the hazards and potential accidents which may occur in the facility. The potential consequences and likelihood of these accidents are analyzed and described. Using the process and criteria described in DOE-STD-3009-94, safety-related structures, systems and components are identified, and the important safety functions of each SSC are described. Additionally, ...
The Reliability Data Management System (RDMS) for safety systems of PHWR type plants has been developed and utilized in the reliability analysis of the special safety systems of Wolsong Unit 1 with plant overhaul period lengthened. The RDMS is developed for the periodic efficient reliability analysis of the safety systems of Wolsong Unit 1. In addition, this system provides the function of analyzing the effects on safety system unavailability if the test period of a test procedure changes as well as the function of optimizing the test periods of safety-related test procedures. The RDMS can be utilized in handling the requests of the regulatory institute actively with regard to the reliability validation of safety systems.
This paper explores the current trends in development of technology-neutral safety requirements to be used in the regulation of future nuclear power reactors and the role of the quantitative safety goals in the design of reactor safety systems. Establishing the requirements concerning the reliability of safety functions rather than on particular systems employed to achieve the functions, as well as the use of the recommendations of the International Commission on Radiological Protection (ICRP) on protection against potential exposure could form the basis of a technology-neutral framework for safety requirements on new reactor designs. Also it could contribute to international harmonisation of nuclear safety assessment practices as part of the licensing processes for future nuclear power plants. (author)
The Programmable Logic Controller (PLC) for use in Nuclear Power Plant safety-related applications is being developed and tested first time in Korea. This safety-related PLC is being developed with requirements of regulatory guideline and industry standards for safety system. To test that the quality of the developed PLC is sufficient to be used in safety critical system, document review and various product testings were performed over the development documents for S/W, H/W, and V/V. This paper provides the performance testing methodology and its effectiveness for PLC platform conducted by KOPEC
The objective of Configuration Risk Management Program(CRMP) is to maintain the safety level by assuring the defense-in-depth of nuclear power plant while the configurations are changed during plant operations, especially for the LP/SD. Such a safety purpose can be achieved by establishing the risk monitoring programs with both quantitative and qualitative features. Generally, the quantitative risk evaluation models, i.e., PRA models are used for the risk evaluation during full power operation, and the qualitative risk evaluation models such as safety function assessment trees are used. Through this study, safety function assessment trees were developed.
Since its creation the nuclear industry has been struggling with the question of how safe is safe enough. Safety is a common goal to all involved in the design, operation and regulation of a nuclear installation. As a concept safety is not easy to define. However, there is a general understanding of what attributes a nuclear power plant should have in order to operate safely. The challenge lies in measuring the attributes. The new competitive open electricity market, in many countries throughout the world, is increasing the economic pressure on operators to lower operating costs without jeopardizing safety. Challenges are occurring at a rate that is unprecedented in the nuclear industry: competitiveness; downsizing; ageing; policy changes; reorganization; restructuring; mergers; globalization; and takeovers demand increasing attention to the management of safety. There are various means to measure ...
Documents an early American industrial process of making blast furnace coke using techniques and equipment from the 19th century. Photographed at Bretz, WV.
There are 760 feederpipes, which they are connected to inlet/outlet of the 380 pressure tube channels on the front of the calandria, in CANDU-type Reactor of Wolsung Nuclear Power Plant. As an ISI(In-Service Inspection) and PSI (Post-Service Inspection) requirements, maintenance activities of measuring the thickness of curvilinear part of feederpipe and inspecting the feederpipe support area within calandria are needed to ensure continued reliable operation of nuclear power plant. And ultrasonic probe is used to measure the thickness of curvilinear part of feederpipe, however workers are exposed to radioactivity irradiation during the measurement period. But, it is exposed to radioactivity irradiation during the measurement period. But, it is impossible to inspect feederpipe support area thoroughly because of narrow and confined accessibility, that is , an inspection space between the pressure tube channels is less than 100 mm and pipes in feederpipe support area are congested. And ...
This update of a system concept entitled ``Maritime hazard prevention and water protection`` makes full use of the technical room for maneuver while considering that reasonable financial and economic conditions must be provided. The update allows on to continue or start the exploitation of feasible technical, logistic and information-technology development potentials. The same applies to the national maritime traffic safety measures developed for the German waterways. Considering the maritime hazards that have been prevailing in the coastal areas of the German North Sea, the conducted damage risk investigations suggest that a large-scale, disastrous oil contamination of the mud flats ecosystem cannot be excluded or controlled definitely in spite of the numerous measures taken. (orig.) [Deutsch] Mit der vorgelegten Fortschreibung zum Systemkonzept ``Gefahrenabwehr und Gewaesserschutz im Seeverkehr`` werden die technisch realisierten ...
ORNL has conducted a Nuclear Power Options Viability Study for the Department of Energy. That study is primarily concerned with new technology which could be developed for initial operation in the 2000 to 2010 time frame. Such technology would have to compete not only with coal options but with incrementally improved commercial light-water-reactors. This survey reported here was undertaken to gain an understanding of the nuclear commercial technology likely to be offered in the late 1980s and perhaps beyond. The three US vendors actively marketing NSSSs are each developing a product for the future which they expect to be more reliable, more maintainable, more economical, and safer than the present plants. These are all essentially 3800-MW(t) designs, although all are studying smaller plants. They apparently will be off offered as standard prelicensed designs with much larger scope than earlier NSSS offerings, with the possibility of firm prices. Westinghouse with Mitsubishi Heavy ...
Dynamic pipe impact tests were performed in order to determine the impact conditions for which a 2 inch Schedule 80 carbon steel target pipe would not be broken if it were impacted during a pipe whip event created by a postulated break of an adjacent larger parallel pipe. Such pipe/pipe impact scenarios are of special interest for the feeder pipes of a CANDU reactor because the large number of closely spaced parallel feeder pipes that carry coolant between large primary system pipes and individual fuel channels in the reactor core makes it impractical to consider providing feeder pipe whip restraints. The testing which was performed involved simulating the behaviour of 3 inch and larger whipping pipes in order to study their impact with 2 inch target pipes pressurized at about 9 MPa with water at a temperature of about 290"0C. In a conservative simulation of the worst pipe/pipe impact event which it has been predicted could occur for adjacent parallel feeder pipes ...
One of the main points for the inherent safety of a pebble bed high temperature reactor (HTR) is to guarantee the safe removal of the after-heat in case of a break-down of all active cooling systems like heat-exchangers or liner-cooling. This will be necessary because it is well known today that graphite pebble bed fuel elements stay intact, if the accident temperature is below 1600 deg. C. Therefore the heat must be taken out of the reactor system by passive, natural law heat-transfer mechanism so that the maximum fuel temperature stays below the specified limit. Today medium-sized HTRs with a power of 750 MW_t_h and more (TGTR-300, HTR 500) reach temperatures of more than 2400 deg. C in small parts of the core in such hypothetical accidents. A possible way to realize the inherent safe heat removal in advanced medium-sized HTRs is to change the form of the core. Instead of employing the standard cylindrical geometry a plate shaped core should be preferred, ...
Research highlights: #-># Red mud residues (RM) were disposed in alumina production. #-># Utilization of Red mud residues was affected by its iron content. #-># Superconducting magnetic separation (HGSMS) was used in iron separation from RM. #-># RM with high and low iron contents were separated in HGSMS. - Abstract: The disposal of bayer red mud tailings now seriously threats the environment safety. Reduction and recycling of red mud is now an urgent work in aluminum industry. High gradient superconducting magnetic separation (HGSMS) system was applied to separate the extreme fine RM particles (<100 #mu#m) into high iron content part and low iron content part. Two sorts of RM were fed in the HGSMS. The iron oxide contents in concentrates were about 65% and 45% when RM 1 and RM 2 were fed respectively. Meanwhile, the residues contained 52.0% or 14.1% iron oxide in residues after eight separation stages when RM 1 and RM 2 were fed respectively. The ...
Before the 1997 Kyoto Protocol on Climate Protection, the fluorinated greenhouse gases HFCs, PFCs, and SF6 (F-gases) aroused little public attention. Since then, the standards on surveying and reporting on national emissions have been rising constantly. Amongst others, the annual reporting to the UNFCCC secretariat makes detailed declarations on use and emissions of F-gases necessary, which have to be filled in specified formats for submission (Common Reporting Format = CRF). The scientific basis has been set out by the UNFCCC guidelines on reporting, in accordance with the instructions laid down in IPCC good practice guidance. Additionally, in Germany the Centralised System of Emissions (ZSE) shall provide a suitable tool to satisfy any quality needs of both activity data and emission factors. From 1995 onwards, activity data and emissions of each individual application sector shall be presented in a comprehensible and transparent way. Therefore, the way of data ...
There are 760 feederpipes, which they are connected to inlet/outlet of the 380 pressure tube channels on the front of the calandria, in CANDU-type Reactor of Wolsung Nuclear Power Plant. As an ISI(In-Service Inspection) and PSI (Post- Service Inspection) requirements, maintenance activities of measuring the thickness of curvilinear part of feederpipe and inspecting the feederpipe support area within calandria are needed to ensure continued reliable operation of nuclear power plant. And untrasonic probe is used to measure the thickness of curvilinear part of feederpipe, however workers are exposed to radioactivity irradiation during the measurement period. But, it is impossible to inspect feederpipe support area thoroughlv because of narrow and confined accessibility, that is, an inspection space between the pressure tube channels is less than 100mm and pipes in feederpipe support area are congested. And also, workers involved in inspecting feederpipe support area are under the jeopardy ...
On nuclear power stations with high temperature reactors and helium turbine cycles (HTR-single circuits) the residual heat from the energy conversion process in the primary and intermediate coolers is removed from cycled gas, helium. Water, which is circulated for safety reasons through a closed circuit, is used for cooling. The primary and intermediate coolers as well as other cooling equipment of the power plant are installed within the reactor building. The heat from the helium turbine cycle is removed to the environment most effectively by natural draught cooling towers. In this way a net plant efficiency of about 40% is attainable. The low quantities of residual heat thereby produced and the high (in comparison with power stations with steam turbine cycles) cooling agent pressure and cooling water reheat pressure in the circulating coolers enable an economically favourable design of the overall 'cold end' to be expected. In the so-called unit range it is ...
A nuclear power plant engineering (NPP) simulator may include many system functions such as thermal-hydraulic calculation, 3D reactor neutron kinetics model, control and protection system, display and operational human-machine interface, intelligent alarm system, etc. If all those functions are simulated using a single code, the size of the program will cause structural or managerial problems, and the hardware requirement could be tremendous. Thus, any local function errors or changes may affect the whole code, which will make development and maintenance extremely costly. So the nondistributed code is not considered to be flexible and feasible. Currently, distributed and parallel technologies have been applied to develop NPPs engineering simulator for safety analysis, verification of advanced main control room display, operation and intelligent alarm design. The distributed simulation divides a huge task into several objects according to ...
The Advanced Test Reactor (ATR) at the Idaho National Engineering Laboratory was designed with some passive safety response attributes which contribute to the safety of the facility. The three passive safety attributes being evaluated in the paper are: 1) In-core and in-vessel natural convection cooling, 2) a passive heat sink capability of the ATR primary coolant system (PCS) for the transfer of decay power from the uninsulated piping to the confinement, and 3) gravity feed of emergency coolant makeup. The safety significance of the ATR passive safety response attributes is that the reactor can passively respond to most transients, given a reactor scram, to provide adequate decay power removal and a significant time for operator action should the normal active heat removal systems and their backup systems both fail. The ATR Interim Level 1 Probabilistic Risk Assessment (PRA) models ...
BACKGROUND: The urgent need for patient safety education for healthcare students has been recognised by many accreditation bodies, but to date there has been sporadic attention to undergraduate/graduate medical programmes. Medical students themselves have identified quality and safety of care as an important area of instruction; as future doctors and healthcare leaders, they must be prepared to practise safe healthcare. Medical education has yet to fully embrace patient safety concepts and principles into existing medical curricula. Universities are continuing to produce graduate doctors lacking in the patient safety knowledge, skills and behaviours thought necessary to deliver safe care. A significant challenge is that patient safety is still a relatively new concept and area of study; thus, many medical educators are unfamiliar with the literature and unsure how to integrate ...
BACKGROUND: The urgent need for patient safety education for healthcare students has been recognised by many accreditation bodies, but to date there has been sporadic attention to undergraduate/graduate medical programmes. Medical students themselves have identified quality and safety of care as an important area of instruction; as future doctors and healthcare leaders, they must be prepared to practise safe healthcare. Medical education has yet to fully embrace patient safety concepts and principles into existing medical curricula. Universities are continuing to produce graduate doctors lacking in the patient safety knowledge, skills and behaviours thought necessary to deliver safe care. A significant challenge is that patient safety is still a relatively new concept and area of study; thus, many medical educators are unfamiliar with the literature and unsure how to integrate ...
The objective of the study is to improve the volume of nuclear power plant which adopts passive safety system concept. The passive safety system reactor is characterized by excellent safety and reliability. But the volume of NSSS (Nuclear Steam Supply System) of the passive safety system reactor is so small that it should be upgraded for commercial operation. For volume upgrade, detailed analyses are performed as follows; core design, hydraulics, design and mechnical structures, and safety analysis. In addition to above analysis, some investigations must be supplied as follows: power density vs. DNB margin decrease, outlet temperature vs. EPRI-URD, additional tests for upgraded reactor, dynamic analysis of mechanical vibration according to expanded reactor vessel and expanded in-core structures, and Merit loss of passive safety system reactor according to design ...
The primary responsibility of the Health, Safety, and Environment (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environment protection. These activities are designed to protect the worker, the public, and the environment. Many disciplines are required to meet the responsibilities, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science, epidemiology, and waste management. New and challenging health and safety problems arise occasionally from the diverse research and development work of the Laboratory. Research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed to study specific problems for the Department of Energy and to help develop better occupational health and safety ...
The Decree specifies basic quality assurance requirements applicable to machines, their parts and materials, civil engineering structures, means for automated control of technological processes including hardware and software, and electricity supply systems related to nuclear safety of nuclear facilities, and stipulates binding procedures for the implementation of technical and organizational provisions associated with the quality of selected equipment to ensure nuclear safety of nuclear facilities. Safety classes are defined for selected equipment. Requirements laid on safety assurance documentation are specified, and requirements placed on safety assurance programmes, their preparation, finalization and approval are defined. Quality assurance requirements are also specified with respect to the designing, manufacture, construction, operation, repair, modification and ...
The Department of Energy (DOE) policy requires that all DOE activities be conducted in a manner that protects the safety of the public and provides a safe and healthful workplace for employees. DOE has also prescribed that all personnel be protected in any explosives operation undertaken. The level of safety provided shall be at least equivalent to that of the best industrial practice. The risk of death or serious injury shall be limited to the lowest practicable minimum. DOE and contractors shall continually review their explosives operations with the aim of achieving further refinements and improvements in safety practices and protective features. This manual describes the Department's explosive safety requirements applicable to operations involving the development, testing, handling, and processing of explosives or assemblies containing explosives. It is intended to reflect the ...
Objectives This paper examines the determinants of the insureds decision to use their health insurance card when seeking outpatient and inpatient health care in Vietnam. Methods Uses Vietnams latest Household Living Standard Survey data and random-intercept logistic regression to assess the influence of the observed individual, household and commune/ward factors on the insureds decision to access health insurance benefits while controlling for the unobserved commune/ward-specific factors. Results Compared to the compulsory enrollees, the voluntary enrollees and the beneficiaries of the Health Care Fund for the Poor are less likely to use their card when seeking inpatient care. An individuals likelihood of accessing insurance benefits varies inversely with income and the level of education,...
Intelligent and decision aiding systems as support to operators are becoming increasingly a necessity in nuclear installations and in nuclear reactors in particular, specially after the Tree Mile Island. Development of new technologies based on linguistic approaches such as fuzzy logic has given rise to much interest during the last years. Fuzzy logic controller (FLC) has many advantage compared to conventional controllers using classical techniques. The aim of the present work is to use a fuzzy logic controller in parallel to actual semi-automatic controller in order to supervise in real time the operation of the research nuclear reactor. The principal of this controller is based on rules which are established previous from experiment using the semi-automatic controller and from the knowledge of the operators. (authors)
This paper presents a new mathematical model for designing distribution networks in a supply chain system considering service level constraint optimizing strategic decisions (location), tactical decisions (inventory), and assigning decisions. In real-world cases, demand, traveling time or any parameters in classical models may change over the period of time. So, considering uncertainty yields more flexibility for the results and the proposed model. In our study, environmental uncertainty is described by discrete scenarios. In this model, we have service level constraint in order to prevent inventory lost in distribution centers (DCs). Also, we assume that customer's demand is stochastic with Poisson distribution function and DCs have coverage radius constraints thus any DC cannot service a...
In the context of safety assessment of radioactive waste repositories, complex radionuclide transport models covering key safety-relevant processes play a major role. In recent Swiss safety assessments, such as Kristallin-I, an important drawback was the limitation in geosphere modelling capability to account for geosphere heterogeneities. In marked contrast to this limitation in modelling capabilities, great effort has been put into investigating the heterogeneity of the geosphere as it impacts on hydrology. Structural geological methods have been used to look at the geometry of the flow paths on a small scale and the diffusion and sorption properties of different rock materials have been investigated. This huge amount of information could however be only partially applied in geosphere transport modelling. To make use of these investigations the 'PICNIC project' was established as a ...
BackgroundPercutaneous endoscopic gastrostomy (PEG) allows long-term tube feeding. Safety of pull-type and introducer PEG placement in oncology patients with head/neck or oesophageal...Full Text Available
BackgroundSafety for diabetic patients means providing the most suitable treatment for each type of diabetic in order to improve monitoring and to prevent the adverse effects of...Full Text Available
The safety, pharmacokinetics, and distribution in tissue of an amphotericin B (AmB)-cholesteryl sulfate colloidal dispersion (ABCD) were compared with those of micellar amphotericin B-deoxycholate (m-AmB)....Full Text Available
The Plutonium Finishing Plant (PFP) previously known as the Plutonium Process and Storage Facility, or Z-Plant, was built and put into operation in 1949. Since 1949 PFP has been used for various processing missions, including plutonium purification, oxide production, metal production, parts fabrication, plutonium recovery, and the recovery of americium (Am-241). The PFP has also been used for receipt and large scale storage of plutonium scrap and product materials. The PFP Final Safety Analysis Report (FSAR) was prepared by WHC to document the hazards associated with the facility, present safety analyses of potential accident scenarios, and demonstrate the adequacy of safety class structures, systems, and components (SSCs) and operational safety requirements (OSRs) necessary to eliminate, control, or mitigate the identified hazards. Documented in this Safety Evaluation Report (SER) ...
Nuclear power plant has several safety features and each safety feature is based on the operation of pumps and valves. Therefore, it is an essential basis for the safety of nuclear power plant to keep operational readiness of pumps and valves by In-Service Test (IST). According to Ministry of Education, Science and Technology (MEST) Bulletin 2008-14, the safety functioned pumps and valves of all nuclear power plants of Korea Hydro and Nuclear Power Co. Ltd.(KHNP) have been tested to verify their performance of safety function. Each safety grade pump has own design requirement and should be tested to identify whether it could meet the requirement. Design requirements and test references of all safety grade pumps of Wolsung Nuclear Power Plant Unit 2 (Wolsung Unit 2) were examined in this study. And the results of the performance test of the ...
Nuclear power plant has several safety features and each safety feature is based on the operation of pumps and valves. Therefore, it is an essential basis for the safety of nuclear power plant to keep operational readiness of pumps and valves by In-Service Test (IST). According to Ministry of Education, Science and Technology (MEST) Bulletin 2008-14, the safety functioned pumps and valves of all nuclear power plants of Korea Hydro and Nuclear Power Co. Ltd.(KHNP) have been tested to verify their performance of safety function. Each safety grade pump has own design requirement and should be tested to identify whether it could meet the requirement. Design requirements and test references of all safety grade pumps of Wolsung Nuclear Power Plant Unit 2 (Wolsung Unit 2) were examined in this study. And the results of the performance test of the ...
This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development ...
This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development ...
Telbivudine is a novel nucleoside drug recently approved for the treatment of patients with chronic hepatitis B. Its nonclinical safety was evaluated in a comprehensive program of studies, including...Full Text Available
An ex-employee's claims that inadequate enforcement of radiation safety regulations allowed excess radiation exposure thereby causing his deteriorating health was not substantiated by a thorough investigation.
A workshop on alternative toxicological testing methodologies was convened by the Scientific Group on Methodologies for the Safety Evaluation of Chemicals (SGOMSEC) 26-31 January 1997 in Ispra, Italy,...Full Text Available
The Global Road Safety Partnership (GRSP) is a global partnership of business, civil society and government working for sustained reduction of road accidents in developing and transition countries. GRSP, which started operations in 1999, has a global secr...
1 The long term safety and efficacy of vigabatrin has been studied in 254 patients with refractory epilepsy (82% with partial seizures) in 23 different clinics in eight European countries....Full Text Available
Objectives:The study was planned to evaluate the efficacy and safety of Livwin (polyherbal formulation) in acute viral hepatitis.Materials...Full Text Available
Ayurvedic drugs have begun to be evaluated in controlled clinical trials. The trials, often placebo controlled, are usually designed to demonstrate superiority. Though the results have been usually...Full Text Available
AIMSTo evaluate and compare the risk of specific safety outcomes in patients prescribed ibuprofen and paracetamol concomitantly with those in patients prescribed ibuprofen or paracetamol...Full Text Available
A public health emergency such as an influenza pandemic will lead to shortages of mechanical ventilators, critical care beds, and other potentially life saving treatments. This will raise difficult...Full Text Available
ObjectiveTo estimate which strategy is the most cost-effective for prevention of preterm birth and associated morbidity.Study DesignFull Text Available
SummarySurvival requires the selection of appropriate behavioural responses in the face of danger. With respect to the threat of predation, both the decision to escape and the underlying...Full Text Available
A ``rule of seven`` implies a scientific organization in which each leader is expected to contribute technically, giving each member a responsibility for the creative work needed for effective leadership. It would decentralize leadership, pushing decisions down to the level where they should be made. Such a structure need not be imposed from above.
Digital information flow within the intensive care unit (ICU) continues to grow, with advances in technology and computational biology. Recent developments in the integration and archiving of these...Full Text Available
For proper tissue morphogenesis, cell divisions and cell fate decisions must be tightly and coordinately regulated. One elegant way to accomplish this is to couple them with asymmetric cell divisions....Full Text Available
Background: Health information technologies (HIT) such as electronic medical records (EMR), computerized physician order entry (CPOE), and clinical decision support systems (CDSS) have...Full Text Available
The article describes control and monitoring concepts in which the delegation of responsibility is becoming more decisive than ever (automation hierarchy), and which are capable of optimized, automatic control of process events in pumped storage plants. 8 refs.
Theoretically, the outcome of World War II in Europe hung in the balance as the Allies poured onto the Normandy beachhead. Following the June 6, 1944 invasion, the Allies continue to come ashore, massively building up men and material inside the beachhead...
The E and P industry has high levels of uncertainty and risk, which oil companies attempt to quantify before embarking on each individual E and P project. However, the actual return on investment often falls well short of the hurdle rate. This discrepancy has been attributed to systemic limitations in decision analysis processes and workflow, which result in repeated underestimation of risk and overestimation of the predicted production of the project. Well designed decision analysis processes in association with clearly defined, multi-scenario analyses of significant technical uncertainties are required. However, simulation of these uncertainties is not realistic given the performance and infrastructure limitations of conventional technology (Begg et al., 2001; Floris and Peersmann, 2000). During the past five years, more than 20 companies have attempted to map the requirements of new technology that is needed to improve uncertainty assessment ...
car running down the track." Choosing to focus on the design of a hydrogen fuel cell model car rather than a solar race car was a deliberate decision for team, "Larry the...
Female sexual promiscuity can have significant effects on male mating decisions because it increases the intensity of competition between ejaculates for fertilization. Because sperm production is costly,...Full Text Available
OBJECTIVES. In this study we tested the association between occupational stress--as measured by job demands, decision latitude, and job strain--and hypertension in a population of 1396 Black and White...Full Text Available
We present a methodology and database mediator tool for integrating modern knowledge-based systems, such as the Stanford EON architecture for automated guideline-based decision-support, with legacy...Full Text Available
ObjectiveMany hospitals utilize antimicrobial management teams (AMTs) to improve patient care. However, most function with minimal computer support. We evaluated the effectiveness...Full Text Available
BackgroundPolyadenylation of RNA has a decisive influence on RNA stability. Depending on the organisms or subcellular compartment, it either enhances transcript stability or targets...Full Text Available
Air pollution abatement measures are not an end in themselves, and undesirable side effects should be taken into account. The proposed emission index takes into account the total emissions caused by a technical project as well as the effects of the individual pollutants.
BackgroundOsteoporosis affects over 200 million people worldwide, and represents a significant cost burden. Although guidelines are available for best practice in osteoporosis, evidence...Full Text Available
Cyberspace and its associated operations present both opportunities and challenges for military and United States Government decision-makers and planners. The Pentagon has formally recognized cyberspace as a domain of warfare. Cyberspace is man-made, dyna...
We describe a decision support system to distinguish among hematology cases directly from microscopic specimens. The system uses an image database containing digitized specimens from normal...Full Text Available
After emergence, adult flies and other insects select a suitable perch and expand their wings. Wing expansion is governed by the hormone bursicon and can be delayed under adverse environmental...Full Text Available
In spite of their rarity, cystic neoplasms of the pancreas are characterized by existing or potential malignancy that cannot be ignored during decisive process with regard to the choice of treatment....Full Text Available
Allometric equations are often used to extrapolate traits in animals for which only body mass estimates are known, such as dinosaurs. One important decision can be whether these equations should be...Full Text Available
BackgroundClassification systems may be useful to direct more aggressive treatment to cancer patients with a relatively poor prognosis. The definition of 'poor prognosis' often lacks...Full Text Available
Six patient assessment systems that have explicit decision rules for replicating team judgments on level of care patient placement were selected for analysis. The six were selected because of their...Full Text Available
Thermodynamic Stable Metal Compositions for Improvement of an Operational Safety of Constructional Materials under Conditions of Multifactor Loadings of an Aggressive Environment
Mitsubishi is now developing a new Pressurized water reactor (PWR), the Mitsubishi simplified PWR (MS-PWR), which has the innovative features of hybrid safety systems (an optimum combination of passive and active systems) and cooling by horizontal steam generators. In order to confirm the feasibility of the Mitsubishi hybrid safety system, various kinds of safety analyses are performed for loss-of-coolant accident events. In parallel to these safety analysis efforts, the following thermal-hydraulic tests are to be performed: (1) thermal-hydraulic test of a horizontal steam generator; (2) integrated thermal-hydraulic test using a simulation loop for the innovative MS-PWR (SLIM).
The major feed-water line break accident is re-analyzed, which is based on Guangdong Daya Bay nuclear power station final safety analysis report, to justify the impacts of the decreasing of auxiliary feed-water flow rate on the safety margin in Daya Bay. The results showed that the accident analysis can meet the demands of acceptance criteria with the auxiliary feed-water flowrate decreasing from 45 m"3/h to 41.8 m"3/h, and enough safety margin is still retained
Nuclear energy related research in Switzerland is concentrated at PSI's Nuclear Energy and Safety Research Department (NES). The activities of the department are concentrated on three main domains of: Safety and related problems of operating plants; safety features of future reactor and fuel cycles; waste management. Comprehensive assessments of energy systems are carried out in cooperation with PSI's General Energy Research Department. Many of the programs are part of collaborations with universities, industry, or international organisations. Progress in 2000 in these topical areas is described in this report. A list of scientific publications in 2000 is also provided.
This document reports the results of the FY 2005 PNNL VPP Program Evaluation, which is a self-assessment of the operational and programmatic performance of the Laboratory related to worker safety and health. The report was compiled by a team of worker representatives and safety professionals who evaluated the Laboratory's worker safety and health programs on the basis of DOE-VPP criteria. The principle elements of DOE's VPP program are: Management Leadership, Employee Involvement, Worksite Analysis, Hazard Prevention and Control, and Safety and Health Training.
This research investigates the impact of national culture and several institutional factors on the safety performance of society and establishes statistically significant relationships between those variables. As expected, the research results reveal that some cultural variables such as uncertainty avoidance, gender orientation and institutional variables such as the degree of law avoidance can directly influence the safety performance of the society. The findings also support the inverted u-curve (Safety Kuznet curve) hypothesis indicating even if we expect a negative trend at the beginning stage of industrialization, we can expect a positive trend in safety performance as their income level continues to improve beyond a certain point.
The Fast Flux Test Facility has provided a very useful framework for testing the advances in Liquid Metal Reactor Safety Technology. During the licensing phase, the switch from a nonmechanistic bounding technique to the mechanistic approach was developed and implemented. During the operational phase, the consideration of new tests and core configurations led to use of the anticipated-transients-without-scram approach for beyond design basis events and the move towards passive safety. The future role of the Fast Flux Test Facility may involve additional passive safety and waste transmutation tests. 26 refs.
The present research has been made to develop and review critically the functional requirements of the specific safety systems of CANDU such as SDS-1, SDS2, ECCS, and containment. Based on R documents for this, a systematic study was made to develop the domestic regulation statements. Also, the conventional laws are carefully reviewed to see the compatibility to CANDU. Also, the safety assessment method for CANDU was studied by reviewing C documents and recommendation of IAEA. Through the present works, the vague policy in the CANDU safety regulation is cleaning up in a systematic form and a new frame to measure the objective risk of nuclear power plants was developed.
The present research has been made to develop and review critically the functional requirements of the specific safety systems of CANDU such as SOS-1, SOS-2, ECCS and containment. Based on R documents for this, a systematic study was made to develop the domestic regulation statements. Also, the conventional laws are carefully reviewed to see the compatibility to CANDU. Also, the safety assessment method for CANDU was studied by reviewing C documents and recommendation of IAEA. Through the present works, the vague policy in the CANDU safety regulation is cleaning up in a systematic form and a new frame to measure the objective risk of nuclear power plants was developed.
Independent drilling contractors own all offshore drilling rigs, which they lease to oil and gas companies for use in their pursuit of their exploration and development plans. Oil and gas companies' demand for these rigs can vary quickly and dramatically in response to changes in the world market for oil and natural gas. As a result, drilling contractors often try to manage excess capacity by idling rigs (known in the industry as "stacking" a rig), reactivating them when demand recovers. This paper examines these decisions over the course of a price cycle in 1998-2000 to investigate the role of firm and rig heterogeneity in determining drillers' decisions about idling and reactivating capacity.
The paper demonstrates an application of advanced decision support tools within the framework of the environmental information system of the Province of Milan. These tools include environmental simulation models, multi criteria analysis, risk analysis and environmental accounting for marketable emission permits. After describing the general structure of the system, three demonstrational case studies are introduced concerning: groundwater pollution management; atmospheric pollution management; urban environmental quality perception and management. In the conclusion, potential use of tools like the ones implemented by the province of Milan within the framework of Local Agenda 21 processes is recalled.
Cesium-137 has contaminated a large area of the wetlands on the Savannah River Site. Remediation of the contaminated wetlands is problematic because current techniques destroy the sensitive ecosystem and generate a higher dose to workers. To address this problem, we proposed a non-trusive, in situ technology to sequester 137Cs in sediments. One intention of this study was to provide information regarding a go/no go decision for future work. Since the proof-of-concept was successful and several minerals were identified as potential candidates for this technology, a go decision was made.
The insertion of innovative technologies to replace baseline technologies used in cost estimation and planning of DOE D&D projects is considered a high risk endeavor by project and programmatic decision makers. It is almost always considered safer to go with the {open_quotes}devil you know{close_quotes} than use a new or untried technology, methodology or system. The decision on the specific technology to be utilized to remediate a problem is often made months or years in advance of execution, and the highly proscriptive documentation of agreements necessary to obtain stakeholder and regulator approval of remedial plans is often counterproductive to considering improved technologies.
Concept Exploration (CE) experiments within the Innovative Confinement Concept Program have a unique role which impacts their contributions to the development of fusion energy. As stated in the FESAC ''Report on Alternate Concepts:'' These [CE] programs are aimed at innovation and basic understanding of relevant scientific phenomena. The emphasis on innovation motivates their application to the search for a better fusion reactor configuration. In addition, because of their unique character the CE experiments offer excellent opportunities to couple fusion-plasma physics to other sciences. A recent example of coupling is the fusion self-organized plasmas to reconnection physics and extra-terrestrial plasmas. Perhaps of even greater importance is the education of the future scientists needed for developing fusion energy. The CE experiments, both at universities and national labs, are of a size students can ''get their hands ...
The rod drop time event of the Daya Bay Nuclear Power Plant is caused by the malfunction of the guide tube developed by Framatome. Three temporary solutions were implemented successively and the long term solution was found in the process of searching for the root cause. The different solutions and the root cause are introduced. The safety analysis and license of the solutions are mainly discussed. Experiences and lessons are drawn by summarizing the important items related to nuclear safety.
The safety analysis checklist scope and the criteria of key parameters needed to be checked for Daya bay reload cycles are introduced. The INCORE code package was used for the safety evaluation of Daya bay unit 2 cycle 2. The method and the contents can not only be applicable for Daya Bay reload cycles but also for Qinshan 600 MW and Qinshan 300 MW reload cycles.
This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development of future radiological safety plans by presenting detailed discussion of the problems and solutions arising during Operation Castle.
This report is designed to cover the overall Operation Castle radiological safety matters from the viewpoint of those issues of direct concern to Headquarters, Joint Task Force Seven. It was written for the express purpose of assisting in the development of future radiological safety plans by presenting detailed discussion of the problems and solutions arising during Operation Castle. Included is a discussion of fallout forecasting techniques.
The 200 Area Interim Storage Area Technical Safety Requirements define administrative controls and design features required to ensure safe operation during receipt and storage of canisters containing spent nuclear fuel. This document is based on the 200 Area Interim Storage Area, Annex D, Final Safety Analysis Report which contains information specific to the 200 Area Interim Storage Area.