WorldWideScience

Sample records for safer process additional

  1. A real-life example of choosing an inherently safer process option

    International Nuclear Information System (INIS)

    Study, Karen

    2007-01-01

    While choosing an inherently safer alternative may seem straightforward, sometimes what seems to be the most obvious alternative may not provide the best risk reduction. The process designer must maintain a broad perspective to be able to recognize all potential hazards when evaluating design options. All aspects of operation such as start-up, shut-down, utility failure, as well as normal operation should be considered. Choosing the inherently safer option is best accomplished early in the option selection phase of a project; however, recycle back to the option selection phase may be needed if an option is not thoroughly evaluated early in the process. In this paper, a project to supply ammonia to a catalytic reactor will be reviewed. During the course of the project, an 'inherently safer' alternative was selected and later discarded due to issues uncovered during the detail design phase. The final option chosen will be compared to (1) the original design and (2) the initial 'inherently safer' alternative. The final option was inherently safer than both the original design and the initial 'inherently safer' alternative even though the design team initially believed that it would not be

  2. Safer operating conditions and optimal scaling-up process for cyclohexanone peroxide reaction

    International Nuclear Information System (INIS)

    Zang, Na; Qian, Xin-Ming; Liu, Zhen-Yi; Shu, Chi-Min

    2015-01-01

    Highlights: • Thermal hazard of cyclohexanone peroxide reaction was measured by experimental techniques. • Levenberg–Marquardt algorithm was adopted to evaluate kinetic parameters. • Safer operating conditions at laboratory scale were acquired by BDs and TDs. • The verified safer operating conditions were used to obtain the optimal scale-up parameters applied in industrial plants. - Abstract: The cyclohexanone peroxide reaction process, one of the eighteen hazardous chemical processes identified in China, is performed in indirectly cooled semibatch reactors. The peroxide reaction is added to a mixture of hydrogen peroxide and nitric acid, which form heterogeneous liquid–liquid systems. A simple and general procedure for building boundary and temperature diagrams of peroxide process is given here to account for the overall kinetic expressions. Such a procedure has been validated by comparison with experimental data. Thermally safer operating parameters were obtained at laboratory scale, and the scaled-up procedure was performed to give the minimum dosing time in an industrial plant, which is in favor of maximizing industrial reactor productivity. The results are of great significance for governing the peroxide reaction process apart from the thermal runaway region. It also greatly aids in determining optimization on operating parameters in industrial plants.

  3. Towards Safer Nanomaterials

    DEFF Research Database (Denmark)

    Hjorth, Rune; Baun, Anders

    2014-01-01

    As nanomaterials become more widespread in everything from industrial processes to consumer products, concerns about human and environmental safety are being taken increasingly more seriously. In our research we are working with minimizing the impact and risks of engineered nanomaterials by looking...... or the exposure and optimally both. Examples include the 5 SAFER principles (Morose, 2010) or screenings of early warning signs (Hansen et al., 2013). Taking the full life cycle of nanomaterials into account, the principles of Green chemistry and Green engineering could also prove useful to reduce...... the environmental impact of nanomaterials (Eckelman et al., 2008). Our research interests include the feasibility of “safer-­‐by-­‐design” approaches, the production of greener nanomaterials and operationalization, adaption and creation of frameworks to facilitate safety engineering. Research and insight...

  4. Consensus statement: Supporting Safer Conception and Pregnancy For Men And Women Living with and Affected by HIV.

    Science.gov (United States)

    Matthews, Lynn T; Beyeza-Kashesya, Jolly; Cooke, Ian; Davies, Natasha; Heffron, Renee; Kaida, Angela; Kinuthia, John; Mmeje, Okeoma; Semprini, Augusto E; Weber, Shannon

    2017-05-13

    Safer conception interventions reduce HIV incidence while supporting the reproductive goals of people living with or affected by HIV. We developed a consensus statement to address demand, summarize science, identify information gaps, outline research and policy priorities, and advocate for safer conception services. This statement emerged from a process incorporating consultation from meetings, literature, and key stakeholders. Three co-authors developed an outline which was discussed and modified with co-authors, working group members, and additional clinical, policy, and community experts in safer conception, HIV, and fertility. Co-authors and working group members developed and approved the final manuscript. Consensus across themes of demand, safer conception strategies, and implementation were identified. There is demand for safer conception services. Access is limited by stigma towards PLWH having children and limits to provider knowledge. Efficacy, effectiveness, safety, and acceptability data support a range of safer conception strategies including ART, PrEP, limiting condomless sex to peak fertility, home insemination, male circumcision, STI treatment, couples-based HIV testing, semen processing, and fertility care. Lack of guidelines and training limit implementation. Key outstanding questions within each theme are identified. Consumer demand, scientific data, and global goals to reduce HIV incidence support safer conception service implementation. We recommend that providers offer services to HIV-affected men and women, and program administrators integrate safer conception care into HIV and reproductive health programs. Answers to outstanding questions will refine services but should not hinder steps to empower people to adopt safer conception strategies to meet reproductive goals.

  5. Safer Systems: A NextGen Aviation Safety Strategic Goal

    Science.gov (United States)

    Darr, Stephen T.; Ricks, Wendell R.; Lemos, Katherine A.

    2008-01-01

    The Joint Planning and Development Office (JPDO), is charged by Congress with developing the concepts and plans for the Next Generation Air Transportation System (NextGen). The National Aviation Safety Strategic Plan (NASSP), developed by the Safety Working Group of the JPDO, focuses on establishing the goals, objectives, and strategies needed to realize the safety objectives of the NextGen Integrated Plan. The three goal areas of the NASSP are Safer Practices, Safer Systems, and Safer Worldwide. Safer Practices emphasizes an integrated, systematic approach to safety risk management through implementation of formalized Safety Management Systems (SMS) that incorporate safety data analysis processes, and the enhancement of methods for ensuring safety is an inherent characteristic of NextGen. Safer Systems emphasizes implementation of safety-enhancing technologies, which will improve safety for human-centered interfaces and enhance the safety of airborne and ground-based systems. Safer Worldwide encourages coordinating the adoption of the safer practices and safer systems technologies, policies and procedures worldwide, such that the maximum level of safety is achieved across air transportation system boundaries. This paper introduces the NASSP and its development, and focuses on the Safer Systems elements of the NASSP, which incorporates three objectives for NextGen systems: 1) provide risk reducing system interfaces, 2) provide safety enhancements for airborne systems, and 3) provide safety enhancements for ground-based systems. The goal of this paper is to expose avionics and air traffic management system developers to NASSP objectives and Safer Systems strategies.

  6. Seriously Mentally Ill Women’s Safer Sex Behaviors and the Theory of Reasoned Action

    Science.gov (United States)

    Randolph, Mary E.; Pinkerton, Steven D.; Somlai, Anton M.; Kelly, Jeffrey A.; Gibson, Richard H.; Hackl, Kristin

    2014-01-01

    Seriously mentally ill women at risk for HIV infection (n = 96) participated in structured interviews assessing sexual and substance use behavior over a 3-month period. The majority of the women (63.5%) did not use condoms. Consistent with the Theory of Reasoned Action, condom use attitudes and perceived social norms about safer sex were associated with safer sex intentions. Supplementing TRA variables with safer sex self-efficacy explained additional variance in safer sex intentions. Greater safer sex intentions were related to both greater condom use and to less frequent unprotected intercourse. In addition, less frequent sex after drug use and a less fatalistic outlook were associated with less frequent unprotected intercourse. Life circumstances specific to this population are particularly important to examine to improve the effectiveness of risk reduction interventions for seriously mentally ill women. PMID:19458268

  7. Volume reduction, a safer and cheaper way of radwaste management

    International Nuclear Information System (INIS)

    Mergan, L.M.; Cordier, J.P.; Storrer, J.A.

    1979-01-01

    Development of 'Volume Reduction' has demonstrated that it is a safer and cheaper radwaste management method. Safer, because of several advantages: decrease of solidified product volume, satisfactory product properties, absence of free water, better control of process parameters, increased encapsulation efficiency ... The corresponding impact on the waste management costs, results in important savings on different factors, as well as regards the operational costs as the investment expenses. Economy in the range of BF 35.000 per m 3 of incoming waste is achievable. The main volume reduction techniques readily available are briefly reviewed

  8. SaferProducts API

    Data.gov (United States)

    US Consumer Product Safety Commission — On March 11, 2011, the U.S. Consumer Product Safety Commission launched SaferProducts.gov. This site hosts the agency's new Publicly Available Consumer Product...

  9. Gaming for Safer Sex: Young German and Turkish People Report No Specific Culture-Related Preferences Toward Educational Games Promoting Safer Sex.

    Science.gov (United States)

    Brüll, Phil; Ruiter, Robert A C; Wiers, Reinout W; Kok, Gerjo

    2016-12-01

    Comprehensive sex education programs specifically designed for adolescents and young adults that take into account gender norms and cultural background have shown promise as a means of countering the high sexually transmitted infection rate in young people. Recently, digital gaming interventions delivered on computers or mobile devices have emerged as another way to promote safer sex behavior in a young population. Tailoring these computer-based interventions to their target population has been recognized to increase positive behavior outcomes. In this qualitative study, we investigated whether young female and male adults from two different cultural backgrounds (all living in Germany) would have different preferences and needs in relation to an educational game promoting safer sex. We conducted four semistructured focus group interviews comprising open-ended questions with male and female participants who had either a German or a Turkish background. In total, 20 individuals, aged between 18 and 22 years, from two socially diverse and ethnically mixed vocational schools in Germany participated. Independent of cultural background and gender, participants preferred a real-world design with a first-person visual perspective over a fantasy-like third-person perspective. Furthermore, they preferred highly customizable avatars. All participants mentioned the importance of including an alcohol-intoxicated avatar and most participants wanted there to be additional information available about various safer sex approaches and about the use of different barrier protection methods. Males and females reported similar preferences for the design of an educational game promoting safer sex, with the only difference being exactly how the topic of having sexual intercourse should be addressed in the game. Males preferred a direct approach, whereas females had a preference for treating this subject more sympathetically. Educational games offer anonymity and can provide young people

  10. Identifying psychosocial variables that predict safer-sex intentions in adolescents and young adults

    Directory of Open Access Journals (Sweden)

    Phil eBrüll

    2016-04-01

    Full Text Available Young people are especially vulnerable to sexually transmitted infections. The triad of deliberate and effective safer-sex behavior encompasses condom use, combined with additional information about a partner’s sexual health, and the kind of sex acts usually performed. To identify psychosocial predictors of young people’s intentions to have safer sex, as related to this triad we conducted an online study with 211 sexually active participants aged between 18 and 24 years. Predictors (i.e. perceived behavioural control, subjective norms and intention taken from Fishbein and Ajzen’s Reasoned Action Approach (RAA, were combined with more distal variables (e.g. behavioral inhibition, sensation seeking, parental monitoring, and knowledge about sexually transmitted infections. Beyond the highly predictive power of RAA variables, additional variance was explained by the number of instances of unprotected sexual intercourse during the last twelve months and reasons for using barrier protection during first sexual intercourse. In particular, past condom nonuse behavior moderated perceived behavioral control related to intended condom use. Further, various distal variables showed significant univariate associations with intentions related to the three behaviors of interest. It may, therefore, be helpful to include measures of past behavior as well as certain additional distal variables in future safer-sex programs designed to promote health sustaining sexual behavior.

  11. SAFER vehicle inspection: a multimodal robotic sensing platform

    Science.gov (United States)

    Page, David L.; Fougerolle, Yohan; Koschan, Andreas F.; Gribok, Andrei; Abidi, Mongi A.; Gorsich, David J.; Gerhart, Grant R.

    2004-09-01

    The current threats to U.S. security both military and civilian have led to an increased interest in the development of technologies to safeguard national facilities such as military bases, federal buildings, nuclear power plants, and national laboratories. As a result, the Imaging, Robotics, and Intelligent Systems (IRIS) Laboratory at The University of Tennessee (UT) has established a research consortium, known as SAFER (Security Automation and Future Electromotive Robotics), to develop, test, and deploy sensing and imaging systems for unmanned ground vehicles (UGV). The targeted missions for these UGV systems include -- but are not limited to --under vehicle threat assessment, stand-off check-point inspections, scout surveillance, intruder detection, obstacle-breach situations, and render-safe scenarios. This paper presents a general overview of the SAFER project. Beyond this general overview, we further focus on a specific problem where we collect 3D range scans of under vehicle carriages. These scans require appropriate segmentation and representation algorithms to facilitate the vehicle inspection process. We discuss the theory for these algorithms and present results from applying them to actual vehicle scans.

  12. Expanding Rational Molecular Design beyond Pharma: Metrics to Guide Safer Chemical Design

    Science.gov (United States)

    The demand for safer, healthier and sustainable products, materials and processes has been increasing over the past several years. Differentiating which chemicals are relatively less hazardous than others, often referred to as “greener” or “sustainable, demands a comprehensive, h...

  13. The business case for transitioning to safer chemicals.

    Science.gov (United States)

    McFadden, Roger D

    2011-01-01

    Emerging domestic and international chemical regulations and a heightened consumer awareness of chemicals of concern in products is challenging American businesses to reevaluate and reconsider their approaches to supply chain management and product design. Some of these companies recognize business opportunities and are responding proactively with innovative strategies and tactics. This article describes steps that Staples Inc., the world's largest office products provider, is taking to meet demand for products that are safer and more sustainable. In trying to meet the demand for safer products, Staples faces significant barriers, including the complexity of supply chains, data gaps, and confidential business information. New collaborations between companies, government, and advocates, and improved tools and criteria for defining safer products enhance the ability of businesses, like Staples, to meet new consumer demands.

  14. SAFERE: Southern African Feminist Review

    African Journals Online (AJOL)

    Feminism and Masculinity in an African Capitalist Context: · EMAIL FULL TEXT EMAIL FULL TEXT DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT. Mwenda G. Ntarangwi, 19-32. http://dx.doi.org/10.4314/safere.v3i1.23948 ...

  15. Shopping for a safer car

    Science.gov (United States)

    2010-01-01

    This brochure provides some helpful tips on what to look for when shopping for a safer car. Automakers are increasingly advertising the safety features of their cars. The problem is sorting out their claims and zeroing in on the safety features that ...

  16. Anger as a moderator of safer sex motivation among low-income urban women.

    Science.gov (United States)

    Schroder, Kerstin E E; Carey, Michael P

    2005-10-01

    Theoretical models suggest that both HIV knowledge and HIV risk perception inform rational decision making and, thus, predict safer sex motivation and behavior. However, the amount of variance explained by knowledge and risk perception is typically small. In this cross-sectional study, we investigated whether the predictive power of HIV knowledge and HIV risk perception on safer sex motivation is affected by trait anger. We hypothesized that anger may disrupt rational decision making, distorting the effects of both HIV knowledge and risk perception on safer sex intentions. Data from 232 low-income, urban women at risk for HIV infection were used to test a path model with past sexual risk behavior, HIV knowledge, and HIV risk perception as predictors of safer sex intentions. Moderator effects of anger on safer sex intentions were tested by simultaneous group comparisons between high-anger and low-anger women (median split). The theoretically expected "rational pattern" was found among low-anger women only, including (a) a positive effect of knowledge on safer sex intentions, and (b) buffer (inhibitor) effects of HIV knowledge and HIV risk perception on the negative path leading from past risk behavior to safer sex intentions. Among high-anger women, an "irrational pattern" emerged, with no effects of HIV knowledge and negative effects of both past risk behavior and HIV risk perception on safer sex intentions. In sum, the results suggest that rational knowledge- and risk-based decisions regarding safer sex may be limited to low-anger women.

  17. Safer v. Estate of Pack.

    Science.gov (United States)

    1996-07-11

    The Superior Court of New Jersey, Appellate Division, recognized "a physician's duty to warn those known to be at risk of avoidable harm from a genetically transmissible condition." During the 1950s, Dr. George Pack treated Donna Shafer's father for a cancerous blockage of the colon and multiple polyposis. In 1990, Safer was diagnosed with the same condition, which she claims is inherited, and, if not diagnosed and treated, invariably will lead to metastic colorectal cancer. Safer alleged that Dr. Pack knew the hereditary nature of the disease, yet failed to warn the immediate family, thus breaching his professional duty to warn. The court did not follow the analysis of the trial court, that a physician has no legal duty to warn the child of a patient of the genetic risk of disease because no physician and patient relationship exists between the doctor and the child.

  18. Safer-drinking strategies used by chronically homeless individuals with alcohol dependence.

    Science.gov (United States)

    Grazioli, Véronique S; Hicks, Jennifer; Kaese, Greta; Lenert, James; Collins, Susan E

    2015-07-01

    Chronically homeless individuals with alcohol dependence experience severe alcohol-related consequences. It is therefore important to identify factors that might be associated with reduced alcohol-related harm, such as the use of safer-drinking strategies. Whereas effectiveness of safer-drinking strategies has been well-documented among young adults, no studies have explored this topic among more severely affected populations, such as chronically homeless individuals with alcohol dependence. The aims of this study were thus to qualitatively and quantitatively document safer-drinking strategies used in this population. Participants (N=31) were currently or formerly chronically homeless individuals with alcohol dependence participating in a pilot study of extended-release naltrexone and harm-reduction counseling. At weeks 0 and 8, research staff provided a list of safer-drinking strategies for participants to endorse. Implementation of endorsed safer-drinking strategies was recorded at the next appointment. At both time points, strategies to buffer the effects of alcohol on the body (e.g., eating prior to and during drinking) were most highly endorsed, followed by changing the manner in which one drinks (e.g., spacing drinks), and reducing alcohol consumption. Quantitative analyses indicated that all participants endorsed safer-drinking strategies, and nearly all strategies were implemented (80-90% at weeks 0 and 8, respectively). These preliminary findings indicate that chronically homeless people with alcohol dependence use strategies to reduce harm associated with their drinking. Larger randomized controlled trials are needed to test whether interventions that teach safer-drinking strategies may reduce overall alcohol-related harm in this population. Copyright © 2015 Elsevier Inc. All rights reserved.

  19. Streamlined approach for environmental restoration (SAFER) plan for corrective action unit 412: clean slate I plutonium dispersion (TTR) tonopah test range, Nevada, revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, Patrick K.

    2015-04-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 412. CAU 412 is located on the Tonopah Test Range and consists of a single corrective action site (CAS), TA-23-01CS, Pu Contaminated Soil. There is sufficient information and historical documentation from previous investigations and the 1997 interim corrective action to recommend closure of CAU 412 using the SAFER process. Based on existing data, the presumed corrective action for CAU 412 is clean closure. However, additional data will be obtained during a field investigation to document and verify the adequacy of existing information and determine whether the CAU 412 closure objectives have been achieved. This SAFER Plan provides the methodology to gather the necessary information for closing the CAU.The following summarizes the SAFER activities that will support the closure of CAU 412:• Collect environmental samples from designated target populations to confirm or disprove the presence of contaminants of concern (COCs) as necessary to supplement existing information.• If no COCs are present, establish clean closure as the corrective action. • If COCs are present, the extent of contamination will be defined and further corrective actions will be evaluated with the stakeholders (NDEP, USAF).• Confirm the preferred closure option is sufficient to protect human health and the environment.

  20. Viral Transmissions: Safer Sex Videos, Disability, and Queer Politics

    Directory of Open Access Journals (Sweden)

    Karisa Butler-Wall

    2016-12-01

    Full Text Available Bringing disability studies into conversation with queer histories of AIDS activism, this article examines the relationship between disability and queer politics in safer sex videos created by AIDS activists in the 1980s. As a form of what the author terms "guerrilla biopolitics," safer sex videos insisted on the viability of queer life and sexual expression at a historical moment of intense homophobia and sex negativity. At the same time, the vision of sexual health and identity they offered risked reproducing racialized and classed ideologies of ableism. Seeking to "crip" our understandings of safer sex discourses and practices, this study explores how risk reduction techniques have been historically linked to imperatives of compulsory able-bodiedness, precluding alternative expressions of queer/crip life.

  1. Anger as a Moderator of Safer Sex Motivation among Low Income Urban Women

    Science.gov (United States)

    Carey, Michael P.

    2005-01-01

    Theoretical models suggest that both HIV knowledge and HIV risk perception inform rational decision-making and, thus, predict safer sex motivation and behavior. However, the amount of variance explained by knowledge and risk perception is typically small. In this cross-sectional study, we investigated whether the predictive power of HIV knowledge and HIV risk perception on safer sex motivation is affected by trait anger. We hypothesized that anger may disrupt rational-decision making, distorting the effects of both HIV knowledge and risk perception on safer sex intentions. Data from 232 low-income, urban women at risk for HIV infection were used to test a path model with past sexual risk behavior, HIV knowledge, and HIV risk perception as predictors of safer sex intentions. Moderator effects of anger on safer sex intentions were tested by simultaneous group comparisons between high-anger and low-anger women (median-split). The theoretically expected “rational pattern” was found among low-anger women only, including (a) a positive effect of knowledge on safer sex intentions, and (b) buffer (inhibitor) effects of HIV knowledge and HIV risk perception on the negative path leading from past risk behavior to safer sex intentions. Among high-anger women, an “irrational pattern” emerged, with no effects of HIV knowledge and negative effects of both past risk behavior and HIV risk perception on safer sex intentions. In sum, the results suggest that rational knowledge and risk-based decisions regarding safer sex may be limited to low-anger women. PMID:16247592

  2. 75 FR 71123 - Agency Information Collection Activities; Proposed Collection; Comment Request; Safer Detergent...

    Science.gov (United States)

    2010-11-22

    ..., cleaners, airplane deicers, and fire-fighting foams. Safer surfactants are those that break down quickly to... protected through regulations.gov or e- mail. The regulations.gov Web site is an ``anonymous access'' system... technology and systems for the purposes of collecting, validating, and verifying information, processing and...

  3. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 575: Area 15 Miscellaneous Sites, Nevada National Security Site, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, Patrick [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

    2014-12-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 575, Area 15 Miscellaneous Sites, identified in the Federal Facility Agreement and Consent Order (FFACO). CAU 575 comprises the following four corrective action sites (CASs) located in Area 15 of the Nevada National Security Site: 15-19-02, Waste Burial Pit, 15-30-01, Surface Features at Borehole Sites, 15-64-01, Decontamination Area, 15-99-03, Aggregate Plant This plan provides the methodology for field activities needed to gather the necessary information for closing each CAS. There is sufficient information and process knowledge from historical documentation and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of CAU 575 using the SAFER process. Additional information will be obtained by conducting a field investigation to document and verify the adequacy of existing information, to affirm the predicted corrective action decisions, and to provide sufficient data to implement the corrective actions. This will be presented in a closure report that will be prepared and submitted to the Nevada Division of Environmental Protection (NDEP) for review and approval.

  4. Feminism, Anthropology and Androcentrism | Ntarangwi | SAFERE ...

    African Journals Online (AJOL)

    SAFERE: Southern African Feminist Review. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 4, No 1 (2000) >. Log in or Register to get access to full text downloads.

  5. Safer childbirth: a rights-based approach.

    Science.gov (United States)

    Boama, Vincent; Arulkumaran, Sabaratnam

    2009-08-01

    The Millennium Development Goals (MDGs) set very high targets for women's reproductive health through reductions in maternal and infant mortality, among other things. Reductions in maternal mortality and morbidity can be achieved through various different approaches, such as the confidential review of maternal deaths, use of evidence-based treatments and interventions, using a health systems approach, use of information technology, global and regional partnerships, and making pregnancy safer through initiatives that increase the focus on human rights. A combination of these and other approaches can have a synergistic impact on reductions in maternal mortality. This paper highlights some of the current global efforts on safer pregnancy with a focus on reproductive rights. We encourage readers to do more in every corner of the world to advocate for women's reproductive rights and, in this way, we may achieve the MDGs by 2015.

  6. Viral Transmissions: Safer Sex Videos, Disability, and Queer Politics

    OpenAIRE

    Karisa Butler-Wall

    2016-01-01

    Bringing disability studies into conversation with queer histories of AIDS activism, this article examines the relationship between disability and queer politics in safer sex videos created by AIDS activists in the 1980s. As a form of what the author terms "guerrilla biopolitics," safer sex videos insisted on the viability of queer life and sexual expression at a historical moment of intense homophobia and sex negativity. At the same time, the vision of sexual health and identity they offered...

  7. CDC Vital Signs: Making Health Care Safer

    Science.gov (United States)

    ... of Page What Can Be Done The Federal government is Implementing activities across all government agencies to ... Making Health Care Safer [PSA – 0:60 seconds] Digital Press Kit: CDC Modeling Predicts Growth of Drug- ...

  8. Experiences Using Pre-Exposure Prophylaxis for Safer Conception Among HIV Serodiscordant Heterosexual Couples in the United States.

    Science.gov (United States)

    Bazzi, Angela R; Leech, Ashley A; Biancarelli, Dea L; Sullivan, Meg; Drainoni, Mari-Lynn

    2017-08-01

    Antiretroviral pre-exposure prophylaxis (PrEP) is a promising HIV prevention strategy for HIV serodiscordant couples (HIV-infected male, uninfected female) seeking safer conception. However, most research on PrEP for safer conception has focused on couples in sub-Saharan Africa; little is known about the perspectives or experiences of heterosexual couples in the United States. We conducted qualitative interviews with six couples (six women and five of their male partners) receiving PrEP for conception services at an urban safety net hospital in the US Northeast. In-depth interview guides explored couple relationships and contextual factors and attitudes, perceptions, and decision-making processes surrounding PrEP for safer conception. Thematic analyses focused on identifying the following emergent themes. We found that couple relationships were situated within broader social and cultural contexts of immigration, family, and community that shaped their experiences with HIV and serodiscordant relationship status. Despite strong partner support within relationships, HIV stigma and disapproval of serodiscordant relationships contributed to couples' feelings of social isolation and subsequent aspirations to have "normal" families. By enabling "natural" conception through condomless sex, PrEP for safer conception provided a sense of enhanced relationship intimacy. Couples called for increasing public awareness of PrEP through positive messaging as a way to combat HIV stigma. Findings suggest that relationship dynamics and broader social contexts appear to shape HIV serodiscordant couples' fertility desires and motivations to use PrEP. However, increased public awareness of PrEP for safer conception may be needed to combat HIV stigma at the community level.

  9. The SAFER Latinos Project: Addressing a Community Ecology Underlying Latino Youth Violence

    Science.gov (United States)

    Edberg, Mark; Cleary, Sean D.; Collins, Elizabeth; Klevens, Joanne; Leiva, Rodrigo; Bazurto, Martha; Rivera, Ivonne; del Cid, Alex Taylor; Montero, Luisa; Calderon, Melba

    2010-01-01

    This paper describes the intervention model, early implementation experience, and challenges for the "Seguridad, Apoyo, Familia, Educacion, y Recursos" (SAFER) Latinos project. The SAFER Latinos project is an attempt to build the evidence for a multilevel participatory youth violence prevention model tailored to the specific circumstances of…

  10. Graphene Based Ultra-Capacitors for Safer, More Efficient Energy Storage

    Science.gov (United States)

    Roberson, Luke B.; Mackey, Paul J.; Zide, Carson J.

    2016-01-01

    Current power storage methods must be continuously improved in order to keep up with the increasingly competitive electronics industry. This technological advancement is also essential for the continuation of deep space exploration. Today's energy storage industry relies heavily on the use of dangerous and corrosive chemicals such as lithium and phosphoric acid. These chemicals can prove hazardous to the user if the device is ruptured. Similarly they can damage the environment if they are disposed of improperly. A safer, more efficient alternative is needed across a wide range of NASA missions. One solution would a solid-state carbon based energy storage device. Carbon is a safer, less environmentally hazardous alternative to current energy storage materials. Using the amorphous carbon nanostructure, graphene, this idea of a safer portable energy is possible. Graphene was electrochemically produced in the lab and several coin cell devices were built this summer to create a working prototype of a solid-state graphene battery.

  11. Safer electronic health records safety assurance factors for EHR resilience

    CERN Document Server

    Sittig, Dean F

    2015-01-01

    This important volume provide a one-stop resource on the SAFER Guides along with the guides themselves and information on their use, development, and evaluation. The Safety Assurance Factors for EHR Resilience (SAFER) guides, developed by the editors of this book, identify recommended practices to optimize the safety and safe use of electronic health records (EHRs). These guides are designed to help organizations self-assess the safety and effectiveness of their EHR implementations, identify specific areas of vulnerability, and change their cultures and practices to mitigate risks.This book pr

  12. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 411. Double Tracks Plutonium Dispersion (Nellis), Nevada Test and Training Range, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Matthews, Patrick K. [Navarro-Intera, LLC (N-I), Las Vegas, NV (United States)

    2015-03-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 411, Double Tracks Plutonium Dispersion (Nellis). CAU 411 is located on the Nevada Test and Training Range and consists of a single corrective action site (CAS), NAFR-23-01, Pu Contaminated Soil. There is sufficient information and historical documentation from previous investigations and the 1996 interim corrective action to recommend closure of CAU 411 using the SAFER process. Based on existing data, the presumed corrective action for CAU 411 is clean closure. However, additional data will be obtained during a field investigation to document and verify the adequacy of existing information, and to determine whether the CAU 411 closure objectives have been achieved. This SAFER Plan provides the methodology to gather the necessary information for closing the CAU. The results of the field investigation will be presented in a closure report that will be prepared and submitted to the Nevada Division of Environmental Protection (NDEP) for review and approval. The site will be investigated based on the data quality objectives (DQOs) developed on November 20, 2014, by representatives of NDEP, the U.S. Air Force (USAF), and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Field Office. The DQO process was used to identify and define the type, amount, and quality of data needed to determine whether CAU 411 closure objectives have been achieved. The following text summarizes the SAFER activities that will support the closure of CAU 411; Collect environmental samples from designated target populations to confirm or disprove the presence of contaminants of concern (COCs) as necessary to supplement existing information; If COCs are no longer present, establish clean closure as the corrective action; If COCs are present, the extent of contamination will be defined and further corrective actions

  13. SAFER, an Analysis Method of Quantitative Proteomic Data, Reveals New Interactors of the C. elegans Autophagic Protein LGG-1.

    Science.gov (United States)

    Yi, Zhou; Manil-Ségalen, Marion; Sago, Laila; Glatigny, Annie; Redeker, Virginie; Legouis, Renaud; Mucchielli-Giorgi, Marie-Hélène

    2016-05-06

    Affinity purifications followed by mass spectrometric analysis are used to identify protein-protein interactions. Because quantitative proteomic data are noisy, it is necessary to develop statistical methods to eliminate false-positives and identify true partners. We present here a novel approach for filtering false interactors, named "SAFER" for mass Spectrometry data Analysis by Filtering of Experimental Replicates, which is based on the reproducibility of the replicates and the fold-change of the protein intensities between bait and control. To identify regulators or targets of autophagy, we characterized the interactors of LGG1, a ubiquitin-like protein involved in autophagosome formation in C. elegans. LGG-1 partners were purified by affinity, analyzed by nanoLC-MS/MS mass spectrometry, and quantified by a label-free proteomic approach based on the mass spectrometric signal intensity of peptide precursor ions. Because the selection of confident interactions depends on the method used for statistical analysis, we compared SAFER with several statistical tests and different scoring algorithms on this set of data. We show that SAFER recovers high-confidence interactors that have been ignored by the other methods and identified new candidates involved in the autophagy process. We further validated our method on a public data set and conclude that SAFER notably improves the identification of protein interactors.

  14. Mass-Produced, Buffer | Masitera | SAFERE: Southern African ...

    African Journals Online (AJOL)

    SAFERE: Southern African Feminist Review. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 3, No 2 (1999) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. DOWNLOAD FULL TEXT Open Access ...

  15. Safer sexual practices among African American women: intersectional socialisation and sexual assertiveness.

    Science.gov (United States)

    Brown, Danice L; Blackmon, Sha'Kema; Shiflett, Alexandra

    2018-06-01

    Scholars have posited that childhood socialisation experiences may play a key role in influencing behaviours and attitudes that contribute to the acquisition of HIV. This study examined the links between past ethnic-racial and gender socialisation, sexual assertiveness and the safe sexual practices of African American college women utilising a cluster analytic approach. After identifying separate racial-gender and ethnic-gender socialisation profiles, results indicated that ethnic-gender socialisation cluster profiles were directly associated with sexual assertiveness and safer sex behaviour. Greater levels of ethnic socialisation and low traditional gender role socialisation were found to be associated with greater sexual assertiveness and safer sex behaviour. Further analysis showed that sexual assertiveness mediated the links between the identified ethnic-gender socialisation profiles and safer sex behaviour. Implications for policy and programme development are discussed.

  16. Access management in Safer Transportation Network Planning : safety principles, planning framework, and library information.

    NARCIS (Netherlands)

    Hummel, T.

    2001-01-01

    This report is one in a series of publications, used in the development of the network planning tool ‘Safer Transportation Network Planning’ (Safer-TNP). The publications were used to guide the development of planning structures, diagnostic tools, planning recommendations, and research information

  17. Intersection planning in Safer Transportation Network Planning : safety principles, planning framework, and library information.

    NARCIS (Netherlands)

    Hummel, T.

    2001-01-01

    This report is one in a series of publications, used in the development of the network planning tool ‘Safer Transportation Network Planning’ (Safer-TNP). The publications were used to guide the development of planning structures, diagnostic tools, planning recommendations, and research information

  18. Route management in Safer Transportation Network Planning : safety principles, planning framework, and library information.

    NARCIS (Netherlands)

    Hummel, T.

    2001-01-01

    This report is one in a series of publications, used in the development of the network planning tool ‘Safer Transportation Network Planning’ (Safer-TNP). The publications were used to guide the development of planning structures, diagnostic tools, planning recommendations, and research information

  19. [Sexual Behavior and Self-Efficacy for the Negotiation of Safer Sex in Heterosexual Persons.

    Science.gov (United States)

    Pérez-Jiménez, David; Santiago-Rivas, Marimer; Serrano-García, Irma

    2009-05-01

    Self-efficacy has been defined as one of the factors that may facilitate or impede safer sex. Studies reveal that peoples in steady relationships practice safer sex less often that those in casual relationships. We conducted a study with 447 sexually active heterosexual adults. A self-administered questionnaire was designed to study the sexual behavior, the male condom use and the practice of mutual masturbation, and the self-efficacy toward these practices. Results show that most men are sexually active and that there is a low frequency of male condom use and the practice of mutual masturbation as safer sex. The majority of those who use the male condom are engage in casual relationships. However, participants have high levels of self-efficacy toward these practices. Although self-efficacy is one of the factors that influence in deciding to practice safer sex, it is not sufficient to reach this goal.

  20. Recommendations for safer radiotherapy: what’s the message?

    Energy Technology Data Exchange (ETDEWEB)

    Dunscombe, Peter, E-mail: peter.dunscombe@albertahealthservices.ca [Department of Oncology, University of Calgary, Calgary, AB (Canada)

    2012-09-28

    Radiotherapy, with close to a million courses delivered per year in North America, is a very safe and effective intervention for a devastating disease. However, although rare, several deeply regrettable incidents have occurred in radiotherapy and have rightly been the subject of considerable public interest. Partly in response to reports of these incidents a variety of authoritative organizations across the globe has harnessed the expertise amongst their members in attempts to identify the measures that will make radiotherapy safer. While the intentions of all these organizations are clearly good it is challenging for the health care providers in the clinic to know where to start with so much advice coming from so many directions. Through a mapping exercise we have identified commonalities between recommendations made in seven authoritative documents and identified those issues most frequently cited. The documents reviewed contain a total of 117 recommendations. Using the 37 recommendations in “Towards Safer Radiotherapy” as the initial base layer, recommendations in the other documents were mapped, adding to the base layer to accommodate all the recommendations from the additional six documents as necessary. This mapping exercise resulted in the distillation of the original 117 recommendations down to 61 unique recommendations. Twelve topics were identified in three or more of the documents as being pertinent to the improvement of patient safety in radiotherapy. They are, in order of most to least cited: training, staffing, documentation, incident learning, communication, check lists, quality control and preventive maintenance, dosimetric audit, accreditation, minimizing interruptions, prospective risk assessment, and safety culture. This analysis provides guidance for the selection of those activities most likely to enhance safety and quality in radiotherapy based on the frequency of citation in selected recent authoritative literature.

  1. Recommendations for safer radiotherapy: what’s the message?

    International Nuclear Information System (INIS)

    Dunscombe, Peter

    2012-01-01

    Radiotherapy, with close to a million courses delivered per year in North America, is a very safe and effective intervention for a devastating disease. However, although rare, several deeply regrettable incidents have occurred in radiotherapy and have rightly been the subject of considerable public interest. Partly in response to reports of these incidents a variety of authoritative organizations across the globe has harnessed the expertise amongst their members in attempts to identify the measures that will make radiotherapy safer. While the intentions of all these organizations are clearly good it is challenging for the health care providers in the clinic to know where to start with so much advice coming from so many directions. Through a mapping exercise we have identified commonalities between recommendations made in seven authoritative documents and identified those issues most frequently cited. The documents reviewed contain a total of 117 recommendations. Using the 37 recommendations in “Towards Safer Radiotherapy” as the initial base layer, recommendations in the other documents were mapped, adding to the base layer to accommodate all the recommendations from the additional six documents as necessary. This mapping exercise resulted in the distillation of the original 117 recommendations down to 61 unique recommendations. Twelve topics were identified in three or more of the documents as being pertinent to the improvement of patient safety in radiotherapy. They are, in order of most to least cited: training, staffing, documentation, incident learning, communication, check lists, quality control and preventive maintenance, dosimetric audit, accreditation, minimizing interruptions, prospective risk assessment, and safety culture. This analysis provides guidance for the selection of those activities most likely to enhance safety and quality in radiotherapy based on the frequency of citation in selected recent authoritative literature.

  2. Recommendations for safer radiotherapy: what’s the message?

    Directory of Open Access Journals (Sweden)

    Peter eDunscombe

    2012-09-01

    Full Text Available Radiotherapy, with close to a million courses delivered per year in North America, is a very safe and effective intervention for a devastating disease. However, although rare, several deeply regrettable incidents have occurred in radiotherapy and have rightly been the subject of considerable public interest. Partly in response to reports of these incidents a variety of authoritative organizations across the globe has harnessed the expertise amongst their members in attempts to identify the measures that will make radiotherapy safer. While the intentions of all these organizations are clearly good it is challenging for the health care providers in the clinic to know where to start with so much advice coming from so many directions. Through a mapping exercise we have identified commonalities between recommendations made in seven authoritative documents and identified those issues most frequently cited. The documents reviewed contain a total of 117 recommendations. Using the 37 recommendations in Towards Safer Radiotherapy as the initial base layer, recommendations in the other documents were mapped, adding to the base layer to accommodate all the recommendations from the additional six documents as necessary. This mapping exercise resulted in the distillation of the original 117 recommendations down to 61 unique recommendations. Twelve topics were identified in three or more of the documents as being pertinent to the improvement of patient safety in radiotherapy. They are, in order of most to least cited: training, staffing, documentation, incident learning, communication, check lists, quality control and preventive maintenance, dosimetric audit, accreditation, minimizing interruptions, prospective risk assessment and safety culture. This analysis provides guidance for the selection of those activities most likely to enhance safety and quality in radiotherapy based on the frequency of citation in selected recent authoritative literature.

  3. Measurement Noninvariance of Safer Sex Self-Efficacy Between Heterosexual and Sexual Minority Black Youth.

    Science.gov (United States)

    Gerke, Donald; Budd, Elizabeth L; Plax, Kathryn

    2016-01-01

    Black and lesbian, gay, bisexual, or questioning (LGBQ) youth in the United States are disproportionately affected by HIV and other sexually transmitted diseases (STDs). Although self-efficacy is strongly, positively associated with safer sex behaviors, no studies have examined the validity of a safer sex self-efficacy scale used by many federally funded HIV/STD prevention programs. This study aims to test factor validity of the Sexual Self-Efficacy Scale by using confirmatory factor analysis (CFA) to determine if scale validity varies between heterosexual and LGBQ Black youth. The study uses cross-sectional data collected through baseline surveys with 226 Black youth (15 to 24 years) enrolled in community-based HIV-prevention programs. Participants use a 4-point Likert-type scale to report their confidence in performing 6 healthy sexual behaviors. CFAs are conducted on 2 factor structures of the scale. Using the best-fitting model, the scale is tested for measurement invariance between the 2 groups. A single-factor model with correlated errors of condom-specific items fits the sample well and, when tested with the heterosexual group, the model demonstrates good fit. However, when tested with the LGBQ group, the same model yields poor fit, indicating factorial noninvariance between the groups. The Sexual Self-Efficacy Scale does not perform equally well among Black heterosexual and LGBQ youth. Study findings suggest additional research is needed to inform development of measures for safer sex self-efficacy among Black LGBQ youth to ensure validity of conceptual understanding and to accurately assess effectiveness of HIV/STD prevention interventions among this population.

  4. Beyond HIV-serodiscordance: Partnership communication dynamics that affect engagement in safer conception care.

    Directory of Open Access Journals (Sweden)

    Lynn T Matthews

    Full Text Available We explored acceptability and feasibility of safer conception methods among HIV-affected couples in Uganda.We recruited HIV-positive men and women on antiretroviral therapy (ART ('index' from the Uganda Antiretroviral Rural Treatment Outcomes cohort who reported an HIV-negative or unknown-serostatus partner ('partner', HIV-serostatus disclosure to partner, and personal or partner desire for a child within two years. We conducted in-depth interviews with 40 individuals from 20 couples, using a narrative approach with tailored images to assess acceptability of five safer conception strategies: ART for the infected partner, pre-exposure prophylaxis (PrEP for the uninfected partner, condomless sex timed to peak fertility, manual insemination, and male circumcision. Translated and transcribed data were analyzed using thematic analysis.11/20 index participants were women, median age of 32.5 years, median of 2 living children, and 80% had HIV-RNA <400 copies/mL. Awareness of HIV prevention strategies beyond condoms and abstinence was limited and precluded opportunity to explore or validly assess acceptability or feasibility of safer conception methods. Four key partnership communication challenges emerged as primary barriers to engagement in safer conception care, including: (1 HIV-serostatus disclosure: Although disclosure was an inclusion criterion, partners commonly reported not knowing the index partner's HIV status. Similarly, the partner's HIV-serostatus, as reported by the index, was frequently inaccurate. (2 Childbearing intention: Many couples had divergent childbearing intentions and made incorrect assumptions about their partner's desires. (3 HIV risk perception: Participants had disparate understandings of HIV transmission and disagreed on the acceptable level of HIV risk to meet reproductive goals. (4 Partnership commitment: Participants revealed significant discord in perceptions of partnership commitment. All four types of partnership

  5. HIV knowledge, risk perception, and safer sex practices among female sex workers in Port Moresby, Papua New Guinea

    Science.gov (United States)

    Bruce, Eunice; Bauai, Ludwina; Sapuri, Mathias; Kaldor, John M; Fairley, Christopher K; Keogh, Louise A

    2011-01-01

    Sex workers are considered a high-risk group for sexually transmitted infections, including human immunodeficiency virus (HIV), and are often targeted by prevention interventions with safer sex messages. The purpose of this study was to explore the extent to which knowledge of HIV and perception of risk influence safer sex practices among female sex workers (FSWs) in Port Moresby, Papua New Guinea. FSWs (n = 174) were recruited from 19 sites to participate in the study. Qualitative data were collected using semistructured interviews with FSWs (n = 142) through focus group discussions and (n = 32) individual interviews. In addition, quantitative data were collected from all FSWs using a short structured, demographic questionnaire. Data were analyzed using recurring themes and calculations of confidence intervals. Despite some common misperceptions, overall, most FSWs were basically aware of the risks of HIV and informed about transmission and prevention modalities but used condoms inconsistently. Most reported using condoms ‘sometimes’, almost one-sixth ‘never’ used condoms, only a fraction used condoms ‘always’ with clients, and none used condoms ‘always’ with regular sexual partners (RSPs). Among these FSWs, being knowledgeable about the risks, transmission, and prevention of HIV did not translate into safe sex. The findings suggest that certain contextual barriers to safer sex practices exist. These barriers could heighten HIV vulnerability and possibly may be responsible for infection in FSWs. Specific interventions that focus on improving condom self-efficacy in FSWs and simultaneously target clients and RSPs with safer sex messages are recommended. PMID:21445375

  6. The WIPP transportation system -- ''Safer than any other''

    International Nuclear Information System (INIS)

    Ward, T.R.; Spooner, R.

    1991-01-01

    The Department of Energy (DOE) has developed an integrated transportation system to transport transuranic (TRU) waste from ten widely dispersed generator sites to the Waste Isolation Pilot Plant (WIPP). The system consists of a Type B container, a specially designed trailer, a lightweight tractor, the DOE TRANSCOM satellite-based vehicle tracking system, and uniquely qualified and highly trained drivers. The DOE has demonstrated that this system is ready to transport the TRU waste to the WIPP site efficiently and safely. Since the system was put in place in November 1988, it has been repeatedly upgraded and enhanced to incorporate additional safety measures. In June of 1989, the National Academy of Sciences (NAS) reviewed the transportation system and concluded that ''the system proposed for transportation of TRU waste to WIPP is safer than that employed for any other hazardous material in the United States today and will reduce risk to very low levels'' (emphasis added). The NAS conclusion was made before the DOE implemented the Enhanced Driver Training Course for carrier drivers. The challenge facing the DOE was to examine the transportation system objectively and determine what additional improvements could be made to further enhance safety

  7. Designing safer living environments support for local government

    CSIR Research Space (South Africa)

    Landman, K

    1999-06-01

    Full Text Available This paper addresses the built environment, the opportunities it presents for crime and the role city planners and urban designers have to play in the design of safer cities and towns. City planners and urban designers can play a role...

  8. Using a narrative to spark safer sex communication

    NARCIS (Netherlands)

    Donné, Lennie; Hoeks, Jacobus; Jansen, C. J. M.

    2017-01-01

    Objective: College students are a group at risk for contracting sexually transmitted infections (STIs). While they are generally well informed about STIs, they do not consistently use condoms. An important element in preventing STIs is safer sex communication, especially with a sexual partner. This

  9. Evaluating the implementation of health and safety innovations under a regulatory context: a collective case study of Ontario's safer needle regulation.

    Science.gov (United States)

    Chambers, Andrea; Mustard, Cameron A; Breslin, Curtis; Holness, Linn; Nichol, Kathryn

    2013-01-22

    Implementation effectiveness models have identified important factors that can promote the successful implementation of an innovation; however, these models have been examined within contexts where innovations are adopted voluntarily and often ignore the socio-political and environmental context. In the field of occupational health and safety, there are circumstances where organizations must adopt innovations to comply with a regulatory standard. Examining how the external environment can facilitate or challenge an organization's change process may add to our understanding of implementation effectiveness. The objective of this study is to describe implementation facilitators and barriers in the context of a regulation designed to promote the uptake of safer engineered medical devices in healthcare. The proposed study will focus on Ontario's safer needle regulation (2007) which requires healthcare organizations to transition to the use of safer engineered medical devices for the prevention of needlestick injuries. A collective case study design will be used to learn from the experiences of three acute care hospitals in the province of Ontario, Canada. Interviews with management and front-line healthcare workers and analysis of supporting documents will be used to describe the implementation experience and examine issues associated with the integration of these devices. The data collection and analysis process will be influenced by a conceptual framework that draws from implementation science and the occupational health and safety literature. The focus of this study in addition to the methodology creates a unique opportunity to contribute to the field of implementation science. First, the study will explore implementation experiences under circumstances where regulatory pressures are influencing the organization's change process. Second, the timing of this study provides an opportunity to focus on issues that arise during later stages of implementation, a phase

  10. Parent-Adolescent Sexual Communication and Adolescent Safer Sex Behavior: A Meta-Analysis

    Science.gov (United States)

    Widman, Laura; Choukas-Bradley, Sophia; Noar, Seth M.; Nesi, Jacqueline; Garrett, Kyla

    2016-01-01

    Importance Parent-adolescent sexual communication has received considerable attention as one factor that can positively impact safer sex among youth; however, the evidence linking communication to youth contraceptive and condom use has not been empirically synthesized. Objective This meta-analysis examined the effect of parent-adolescent sexual communication on youth safer sex behavior and explored potential moderators of this association. Data Sources A systematic search was conducted of studies published through June 2014 using Medline, PsycINFO, and Communication & Mass Media Complete databases and relevant review articles. Study Selection Studies were included if they: 1) sampled adolescents (mean sample age≤18); 2) included an adolescent report of sexual communication with parent(s); 3) measured safer sex behavior; and 4) were published in English. Data Extraction and Synthesis Correlation coefficients (r) and 95% confidence intervals (CIs) were computed from studies and meta-analyzed using random-effects models. Main Outcomes and Measures The primary outcome was safer sex behavior, including use of contraceptives/birth control or condoms. Results Seventy-one independent effects representing over three decades of research on 25,314 adolescents (mean age = 15.1) were synthesized. Across studies, there was a small, significant weighted mean effect (r = .10, [95% CI:0.08–0.13]) linking parent-adolescent sexual communication to safer sex behavior, which was statistically heterogeneous (Q = 203.50, p communication with girls (r = .12) than boys (r = .04), and among youth who discussed sex with mothers (r = .14) compared to fathers (r = .03). Effects did not differ for contraceptive versus condom use, or among longitudinal versus cross-sectional studies, indicating parent sexual communication had a similar impact across study designs and outcomes. Several methodological issues were identified in the literature; future studies can improve on these by measuring

  11. Land use planning in Safer Transportation Network Planning : safety principles, planning framework, and library information.

    NARCIS (Netherlands)

    Hummel, T.

    2001-01-01

    This report is one in a series of publications, used in the development of the network planning tool ‘Safer Transportation Network Planning’ (Safer-TNP). The publications were used to guide the development of planning structures, diagnostic tools, planning recommendations, and research information

  12. Safer handling practice: influence of staff education on older people.

    Science.gov (United States)

    Wilson, Christine Brown

    The purpose of this small-scale survey was to explore the level of moving and handling training undertaken by nurses within private sector continuing care environments and the potential this training had to influence the care of older people. This study uses a definition of safer handling practice derived from existing literature to examine how nurses report the application of this training and whether they observe changes to the mobility of older people within their care. The limitations of this study indicate that generalizations must be made cautiously. However, this study tentatively suggests that potential exists to influence positively the use of safer handling practice as defined within this study. Recommendations for further study are made.

  13. A Peer-Led, Social Media-Delivered, Safer Sex Intervention for Chinese College Students: Randomized Controlled Trial.

    Science.gov (United States)

    Sun, Wai Han; Wong, Carlos King Ho; Wong, William Chi Wai

    2017-08-09

    The peer-led, social media-delivered intervention is an emerging method in sexual health promotion. However, no research has yet investigated its effectiveness as compared with other online channels or in an Asian population. The objective of this study is to compare a peer-led, social media-delivered, safer sex intervention with a sexual health website. Both conditions target Chinese college students in Hong Kong. A randomized controlled trial was conducted with a peer-led, safer sex Facebook group as the intervention and an existing online sexual health website as the control. The intervention materials were developed with peer input and followed the information-motivation-behavioral skills model; the intervention was moderated by peer educators. The participants filled out the online questionnaires before and after the 6-week intervention period. Outcome evaluations included safer sex attitudes, behavioral skills, and behaviors, while process evaluation focused on online experience, online-visiting frequency, and online engagement. The effect of online-visiting frequency and online engagement on outcome variables was investigated. Of 196 eligible participants-100 in the control group and 96 in the intervention group-who joined the study, 2 (1.0%) control participants joined the Facebook group and 24 of the remaining 194 participants (12.4%) were lost to follow-up. For the process evaluation, participants in the intervention group reported more satisfying online experiences (Psocial media-delivered, safer sex intervention was found to be feasible and effective in improving attitudes toward condom use and behavioral skills, but was not significantly more effective than a website. Future research may focus on the long-term effectiveness and cost-effectiveness of this popular method, as well as the potential cultural differences of using social media between different countries. Chinese Clinical Trial Registry (ChiCTR): ChiCTR-IOR-16009495; http

  14. Pregnancy termination in Matlab, Bangladesh: trends and correlates of use of safer and less-safe methods.

    Science.gov (United States)

    DaVanzo, Julie; Rahman, Mizanur

    2014-09-01

    Menstrual regulation (MR), a relatively safe form of pregnancy termination, is legal in Bangladesh during the early stages of pregnancy. However, little is known about the factors associated with whether women who terminate pregnancies choose this method or a less-safe one. Data from the Matlab Demographic Surveillance System on 122,691 pregnancies-5,221 (4.3%) of which were terminated-were used to examine trends between 1989 and 2008 in termination and in use of safer methods (MR or dilation and curettage) and less-safe (all other) methods of pregnancy termination. Logistic and multinomial logistic regressions were used to assess factors associated with whether women terminate pregnancies and whether they use safer methods. Sixty-seven percent of pregnancy terminations were by safer methods and 33% by less-safe means. The proportion of pregnancies that were terminated increased between 1989 and 2008; this increase was entirely due to increased use of safer methods. Women younger than 18 and those 25 or older were more likely than women aged 20-24 to terminate their pregnancies (odds ratios ranged from 1.5 among women aged 16-17 or 25-29 to 26.1 among those aged 45 or older). Among women who terminated their pregnancies, those aged 25-44 were more likely than those aged 20-24 to use a safer method. Compared with women who had no formal education, those with some education were more likely to terminate their pregnancies and to do so using safer methods. A growing proportion of pregnancies in Matlab are terminated, and these terminations are increasingly done using safer methods.

  15. System Hardening Architecture for Safer Access to Critical Business ...

    African Journals Online (AJOL)

    System Hardening Architecture for Safer Access to Critical Business Data. ... and the threat is growing faster than the potential victims can deal with. ... in this architecture are applied to the host, application, operating system, user, and the ...

  16. NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth

    Science.gov (United States)

    (NASA) and University College London (UCL) for a cutting-edge study on lithium-ion (Li-ion) battery and in Space | News | NREL NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth and in Space NREL, NASA, and UCL Team Up to Make Lithium-Ion Batteries Safer on Earth and in Space

  17. AIDS in Zimbabwe: | Sibanda | SAFERE: Southern African Feminist ...

    African Journals Online (AJOL)

    SAFERE: Southern African Feminist Review. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 3, No 1 (1999) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. DOWNLOAD FULL TEXT Open Access ...

  18. One being White | Newman | SAFERE: Southern African Feminist ...

    African Journals Online (AJOL)

    SAFERE: Southern African Feminist Review. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 3, No 2 (1999) >. Log in or Register to get access to full text downloads. Username, Password, Remember me, or Register. DOWNLOAD FULL TEXT Open Access ...

  19. Community Influences on Married Women's Safer Sex Negotiation Attitudes in Bangladesh: A Multilevel Analysis.

    Science.gov (United States)

    Jesmin, Syeda S; Cready, Cynthia M

    2016-02-01

    The influence of disadvantaged or deprived community on individuals' health risk-behaviors is increasingly being documented in a growing body of literature. However, little is known about the effects of community characteristics on women's sexual attitudes and behaviors. To examine community effects on married women's safer sex negotiation attitudes, we analyzed cross-sectional data from the 2011 Bangladesh Demographic and Health Surveys on a sample of 15,134 married women in 600 communities. We estimated two multilevel logistic regression models. Model 1, which included only individual-level variables, showed that women's autonomy/empowerment, age, and HIV knowledge had significant associations with their safer sex negotiation attitudes. We did not find any socioeconomic status gradient in safer sex negotiation attitudes at the individual level. Adding community-level variables in Model 2 significantly improved the fit of the model. Strikingly, we found that higher community-level poverty was associated with greater positive safer sex negotiation attitudes. Prevailing gender norms and overall women's empowerment in the community also had significant effects. While research on community influences calls for focusing on disadvantaged communities, our research highlights the importance of not underestimating the challenges that married women in economically privileged communities may face in negotiating safer sex. To have sufficient and equitable impact on married women's sexual and reproductive health, sexual and reproductive health promotion policies and programs need to be directed to women in wealthier communities as well.

  20. Evaluating the implementation of health and safety innovations under a regulatory context: A collective case study of Ontario’s safer needle regulation

    Directory of Open Access Journals (Sweden)

    Chambers Andrea

    2013-01-01

    Full Text Available Abstract Background Implementation effectiveness models have identified important factors that can promote the successful implementation of an innovation; however, these models have been examined within contexts where innovations are adopted voluntarily and often ignore the socio-political and environmental context. In the field of occupational health and safety, there are circumstances where organizations must adopt innovations to comply with a regulatory standard. Examining how the external environment can facilitate or challenge an organization’s change process may add to our understanding of implementation effectiveness. The objective of this study is to describe implementation facilitators and barriers in the context of a regulation designed to promote the uptake of safer engineered medical devices in healthcare. Methods The proposed study will focus on Ontario’s safer needle regulation (2007 which requires healthcare organizations to transition to the use of safer engineered medical devices for the prevention of needlestick injuries. A collective case study design will be used to learn from the experiences of three acute care hospitals in the province of Ontario, Canada. Interviews with management and front-line healthcare workers and analysis of supporting documents will be used to describe the implementation experience and examine issues associated with the integration of these devices. The data collection and analysis process will be influenced by a conceptual framework that draws from implementation science and the occupational health and safety literature. Discussion The focus of this study in addition to the methodology creates a unique opportunity to contribute to the field of implementation science. First, the study will explore implementation experiences under circumstances where regulatory pressures are influencing the organization's change process. Second, the timing of this study provides an opportunity to focus on issues

  1. Documentary shows how public employment is making cities safer ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2016-06-10

    Jun 10, 2016 ... In an engaging new documentary film, researchers from the Centre for the Study of Violence and Reconciliation share their insights of how a public employment program in South Africa is making cities safer and more inclusive.

  2. Beyond HIV-serodiscordance: Partnership communication dynamics that affect engagement in safer conception care.

    Science.gov (United States)

    Matthews, Lynn T; Burns, Bridget F; Bajunirwe, Francis; Kabakyenga, Jerome; Bwana, Mwebesa; Ng, Courtney; Kastner, Jasmine; Kembabazi, Annet; Sanyu, Naomi; Kusasira, Adrine; Haberer, Jessica E; Bangsberg, David R; Kaida, Angela

    2017-01-01

    We explored acceptability and feasibility of safer conception methods among HIV-affected couples in Uganda. We recruited HIV-positive men and women on antiretroviral therapy (ART) ('index') from the Uganda Antiretroviral Rural Treatment Outcomes cohort who reported an HIV-negative or unknown-serostatus partner ('partner'), HIV-serostatus disclosure to partner, and personal or partner desire for a child within two years. We conducted in-depth interviews with 40 individuals from 20 couples, using a narrative approach with tailored images to assess acceptability of five safer conception strategies: ART for the infected partner, pre-exposure prophylaxis (PrEP) for the uninfected partner, condomless sex timed to peak fertility, manual insemination, and male circumcision. Translated and transcribed data were analyzed using thematic analysis. 11/20 index participants were women, median age of 32.5 years, median of 2 living children, and 80% had HIV-RNA perception: Participants had disparate understandings of HIV transmission and disagreed on the acceptable level of HIV risk to meet reproductive goals. (4) Partnership commitment: Participants revealed significant discord in perceptions of partnership commitment. All four types of partnership miscommunication introduced constraints to autonomous reproductive decision-making, particularly for women. Such miscommunication was common, as only 2 of 20 partnerships in our sample were mutually-disclosed with agreement across all four communication themes. Enthusiasm for safer conception programming is growing. Our findings highlight the importance of addressing gendered partnership communication regarding HIV disclosure, reproductive goals, acceptable HIV risk, and commitment, alongside technical safer conception advice. Failing to consider partnership dynamics across these domains risks limiting reach, uptake, adherence to, and retention in safer conception programming.

  3. Parent-Adolescent Sexual Communication and Adolescent Safer Sex Behavior: A Meta-Analysis.

    Science.gov (United States)

    Widman, Laura; Choukas-Bradley, Sophia; Noar, Seth M; Nesi, Jacqueline; Garrett, Kyla

    2016-01-01

    Parent-adolescent sexual communication has received considerable attention as a factor that can positively affect safer sex behavior among youth; however, the evidence linking such communication to youth contraceptive and condom use has not been empirically synthesized. To examine the effect of parent-adolescent sexual communication on safer sex behavior among youth and explore potential moderators of this association. A systematic search of studies published from database inception through June 30, 2014, using the MEDLINE, PsycINFO, and Communication & Mass Media Complete databases and relevant review articles yielded 5098 studies, of which 52 studies with 25,314 adolescents met the study eligibility criteria. Analysis was conducted from July 1, 2014, to July 27, 2015. Studies were included if they sampled adolescents (mean sample age ≤18 years), included an adolescent report of sexual communication with one or both parents, measured safer sex behavior, and were published in English. Correlation coefficients (r) and 95% CIs were computed from studies and meta-analyzed using random-effects models. Safer sex behavior, including use of contraceptives or condoms. Fifty-two articles, including 71 independent effects representing more than 3 decades of research on 25,314 adolescents (weighted mean age, 15.2 years) were synthesized. Across studies, there was a significant weighted mean effect (r = 0.10; 95% CI, 0.08-0.13) linking parent-adolescent sexual communication with safer sex behavior, which was statistically heterogeneous (Q = 203.50, P communication with girls (r = 0.12) than boys (r = 0.04) and among youth who discussed sex with their mothers (r = 0.14) compared with their fathers (r = 0.03). Effects did not differ for contraceptive vs condom use or among longitudinal vs cross-sectional studies, indicating that parent sexual communication had a similar effect across study designs and outcomes. Several methodological issues were

  4. Using a Narrative to Spark Safer Sex Communication

    Science.gov (United States)

    Donné, Lennie; Hoeks, John; Jansen, Carel

    2017-01-01

    Objective: College students are a group at risk for contracting sexually transmitted infections (STIs). While they are generally well informed about STIs, they do not consistently use condoms. An important element in preventing STIs is safer sex communication, especially with a sexual partner. This may be difficult, however, because of a lack of…

  5. Motivational influences on the safer sex behavior of agency-based male sex workers.

    Science.gov (United States)

    Smith, Michael D; Seal, David W

    2008-10-01

    Although indoor male sex workers (MSWs) have been found to engage in lower rates of HIV risk behavior with clients than street-based MSWs, few studies have examined the motivations behind such practices. We interviewed 30 MSWs working for the same escort agency regarding their safer sex practices with clients and their reasons for these. As in other research, MSWs reported little risk behavior with clients. Five motivational themes related to safer sex on the job emerged: health concerns, emotional intimacy, client attractiveness, relationships, and structural work factors. Results suggest that participants engaged in rational decision-making relative to sex with clients, facilitated by reduced economic incentive for riskier behavior and a supportive social context. MSWs desired a safe sexual work place, personal integrity, and minimal negative consequences to personal relationships. Collaborating with sex work employers to study their role in encouraging a safer workplace may be important to future research.

  6. A Safer Way to Fight Malaria in Mexico | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2010-10-18

    supported malaria-control strategy in Mexico. The key is working together. Scientists pinpoint sources of malaria; communities destroy mosquito breeding grounds, such as algae in rivers, and spray homes with a safer pesticide.

  7. Toetsing van het gehalte duurzame veiligheid met Safer Transportation Network Planning : integratie van de ‘DV-gehaltemeter’ in het ontwerpprogramma ‘Safer-TNP’

    NARCIS (Netherlands)

    Hummel, T.

    2001-01-01

    Testing the sustainable-safety contents with Safer Transportation Network Planning. In the publication entitled “Developing a sustainable-safety meter (DV-meter) for measuring the sustainable-safety contents” (Van der Kooi & Dijkstra, 2000), the development of and a pilot measurement with a

  8. Multi-level Correlates of Safer Conception Methods Awareness and ...

    African Journals Online (AJOL)

    Many people living with HIV desire childbearing, but low cost safer conception methods (SCM) such as timed unprotected intercourse (TUI) and manual ... including perceived willingness to use SCM, knowledge of respondent's HIV status, HIV-seropositivity, marriage and equality in decision making within the relationship.

  9. Does my step look big in this? A visual illusion leads to safer stepping behaviour.

    Directory of Open Access Journals (Sweden)

    David B Elliott

    Full Text Available BACKGROUND: Tripping is a common factor in falls and a typical safety strategy to avoid tripping on steps or stairs is to increase foot clearance over the step edge. In the present study we asked whether the perceived height of a step could be increased using a visual illusion and whether this would lead to the adoption of a safer stepping strategy, in terms of greater foot clearance over the step edge. The study also addressed the controversial question of whether motor actions are dissociated from visual perception. METHODOLOGY/PRINCIPAL FINDINGS: 21 young, healthy subjects perceived the step to be higher in a configuration of the horizontal-vertical illusion compared to a reverse configuration (p = 0.01. During a simple stepping task, maximum toe elevation changed by an amount corresponding to the size of the visual illusion (p<0.001. Linear regression analyses showed highly significant associations between perceived step height and maximum toe elevation for all conditions. CONCLUSIONS/SIGNIFICANCE: The perceived height of a step can be manipulated using a simple visual illusion, leading to the adoption of a safer stepping strategy in terms of greater foot clearance over a step edge. In addition, the strong link found between perception of a visual illusion and visuomotor action provides additional support to the view that the original, controversial proposal by Goodale and Milner (1992 of two separate and distinct visual streams for perception and visuomotor action should be re-evaluated.

  10. Consumers want safer meat - but not at all costs

    DEFF Research Database (Denmark)

    Mørkbak, Morten Raun; Christensen, Tove; Gyrd-Hansen, Dorte

    2008-01-01

    Consumers, the public authorities, and the food industry are all concerned with the safety of meat. The increasing demand for safer food from the consumers and the public authorities puts pressure on producers to identify efficient methods to reduce risks. Earlier studies have shown that consumer...

  11. Advanced and safer lithium-ion battery based on sustainable electrodes

    KAUST Repository

    Ding, Xiang; Huang, Xiaobing; Jin, Junling; Ming, Hai; Wang, Limin; Ming, Jun

    2018-01-01

    Seeking advanced and safer lithium-ion battery with sustainable characteristic is significant for the development of electronic devices and electric vehicles. Herein, a new porous TiO nanobundles (PTNBs) is synthesized though a scalable and green

  12. SAFERE: Southern African Feminist Review - Vol 3, No 1 (1999)

    African Journals Online (AJOL)

    Feminism and Masculinity in an African Capitalist Context: · EMAIL FULL TEXT EMAIL FULL TEXT DOWNLOAD FULL TEXT DOWNLOAD FULL TEXT. Mwenda G. Ntarangwi, 19-32. http://dx.doi.org/10.4314/safere.v3i1.23948 ...

  13. Immobilizer-assisted management of metal-contaminated agricultural soils for safer food production.

    Science.gov (United States)

    Kim, Kwon-Rae; Kim, Jeong-Gyu; Park, Jeong-Sik; Kim, Min-Suk; Owens, Gary; Youn, Gyu-Hoon; Lee, Jin-Su

    2012-07-15

    Production of food crops on metal contaminated agricultural soils is of concern because consumers are potentially exposed to hazardous metals via dietary intake of such crops or crop derived products. Therefore, the current study was conducted to develop management protocols for crop cultivation to allow safer food production. Metal uptake, as influenced by pH change-induced immobilizing agents (dolomite, steel slag, and agricultural lime) and sorption agents (zeolite and compost), was monitored in three common plants representative of leafy (Chinese cabbage), root (spring onion) and fruit (red pepper) vegetables, in a field experiment. The efficiency of the immobilizing agents was assessed by their ability to decrease the phytoavailability of metals (Cd, Pb, and Zn). The fruit vegetable (red pepper) showed the least accumulation of Cd (0.16-0.29 mgkg(-1) DW) and Pb (0.2-0.9 mgkg(-1) DW) in edible parts regardless of treatment, indicating selection of low metal accumulating crops was a reasonable strategy for safer food production. However, safer food production was more likely to be achievable by combining crop selection with immobilizing agent amendment of soils. Among the immobilizing agents, pH change-induced immobilizers were more effective than sorption agents, showing decreases in Cd and Pb concentrations in each plant well below standard limits. The efficiency of pH change-induced immobilizers was also comparable to reductions obtained by 'clean soil cover' where the total metal concentrations of the plow layer was reduced via capping the surface with uncontaminated soil, implying that pH change-induced immobilizers can be practically applied to metal contaminated agricultural soils for safer food production. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Short-Term Impact of Safer Choices: A Multicomponent, School-Based HIV, Other STD, and Pregnancy Prevention Program.

    Science.gov (United States)

    Coyle, Karin; Basen-Engquist, Karen; Kirby, Douglas; Parcel, Guy; Banspach, Stephen; Harrist, Ronald; Baumler, Elizabeth; Weil, Marsha

    1999-01-01

    Evaluated the effectiveness of the first year of "Safer Choices," a two-year, multicomponent HIV, STD, and pregnancy-prevention program for high school students based on social theory. Student self-report surveys indicated that "Safer Choices" succeeded in reducing selected risk behaviors and in enhancing selected protective…

  15. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 553: Areas 19, 20 Mud Pits and Cellars, Nevada Test Site, Nevada, Rev. No. 0

    International Nuclear Information System (INIS)

    Boehlecke, Robert F.

    2006-01-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions necessary for the closure of Corrective Action Unit (CAU) 553: Areas 19, 20 Mud Pits and Cellars, Nevada Test Site (NTS), Nevada. It has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (FFACO) (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense. A SAFER may be performed when the following criteria are met: (1) Conceptual corrective actions are clearly identified (although some degree of investigation may be necessary to select a specific corrective action before completion of the Corrective Action Investigation [CAI]); (2) Uncertainty of the nature, extent, and corrective action must be limited to an acceptable level of risk; (3) The SAFER Plan includes decision points and criteria for making data quality objective (DQO) decisions. The purpose of the investigation will be to document and verify the adequacy of existing information; to affirm the decision for clean closure, closure in place, or no further action; and to provide sufficient data to implement the corrective action. The actual corrective action selected will be based on characterization activities implemented under this SAFER Plan. This SAFER Plan identifies decision points developed in cooperation with the Nevada Department of Environmental Protection (NDEP), where the DOE, National Nuclear Security Administration Nevada Site Office (NNSA/NSO) will reach consensus with the NDEP before beginning the next phase of work. Corrective Action Unit 553 is located in Areas 19 and 20 of the NTS, approximately 65 miles (mi) northwest of Las Vegas, Nevada (Figure 1-1). Corrective Action Unit 553 is comprised of the four Corrective Action Sites (CASs) shown on Figure 1-1 and listed below: 19-99-01, Mud Spill; 19-99-11, Mud Spill; 20-09-09, Mud Spill; and 20-99-03, Mud Spill. There is sufficient information and process

  16. A safer and flexible method for the oxygen functionalization of carbon nanotubes by nitric acid vapors

    International Nuclear Information System (INIS)

    Santangelo, Saveria; Piperopoulos, Elpida; Fazio, Enza; Faggio, Giuliana; Ansari, Shabana; Lanza, Maurizio; Neri, Fortunato; Messina, Giacomo; Milone, Candida

    2014-01-01

    The functionalization by nitric acid vapors at azeotropic concentration has been recently proposed to eliminate drawbacks of the widely utilized liquid phase functionalization method. This work suggests to exploit the so-called “salt effect” to improve the vapor phase oxidation method in terms of safety and flexibility. Increasing the relative volatility of acid, the addition of Mg(NO 3 ) 2 salt to the HNO 3 + H 2 O solution allows (i) obtaining vapors with HNO 3 at the azeotropic concentration from a more diluted liquid solution (i.e. operating under safer conditions), and (ii) varying the concentration of HNO 3 in the vapor phase even above the azeotropic concentration limit (with improved process flexibility). High-resolution transmission electron microscopy, thermo-gravimetry, Raman spectroscopy and X-ray photoemission spectroscopy systematic analyses are carried out on pristine and oxidized nanotubes in order to assess their functionalization degree, surface chemistry and structural evolution. The most relevant finding of this preliminary study is that the nanotube functionalization extent increases linearly with the HNO 3 vapor concentration.

  17. A safer and flexible method for the oxygen functionalization of carbon nanotubes by nitric acid vapors

    Energy Technology Data Exchange (ETDEWEB)

    Santangelo, Saveria, E-mail: saveria.santangelo@unirc.it [Dipartimento di Ingegneria Civile, dell’Energia, dell’Ambiente e dei Materiali (DICEAM), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Piperopoulos, Elpida [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Fazio, Enza [Dipartimento di Fisica e di Scienze della Terra (DFST), Università di Messina, 98166 Messina (Italy); Faggio, Giuliana [Dipartimento di Ingegneria dell’Informazione, delle Infrastrutture e dell’Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Ansari, Shabana [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy); Lanza, Maurizio [Istituto per i Processi Chimico Fisici (IPCF) del CNR, 98158 Messina (Italy); Neri, Fortunato [Dipartimento di Fisica e di Scienze della Terra (DFST), Università di Messina, 98166 Messina (Italy); Messina, Giacomo [Dipartimento di Ingegneria dell’Informazione, delle Infrastrutture e dell’Energia Sostenibile (DIIES), Università “Mediterranea”, 89122 Reggio Calabria (Italy); Milone, Candida [Dipartimento di Ingegneria Eletronica, Chimica ed Ingegneria Industriale (DIECII), Università di Messina, 98166 Messina (Italy)

    2014-06-01

    The functionalization by nitric acid vapors at azeotropic concentration has been recently proposed to eliminate drawbacks of the widely utilized liquid phase functionalization method. This work suggests to exploit the so-called “salt effect” to improve the vapor phase oxidation method in terms of safety and flexibility. Increasing the relative volatility of acid, the addition of Mg(NO{sub 3}){sub 2} salt to the HNO{sub 3} + H{sub 2}O solution allows (i) obtaining vapors with HNO{sub 3} at the azeotropic concentration from a more diluted liquid solution (i.e. operating under safer conditions), and (ii) varying the concentration of HNO{sub 3} in the vapor phase even above the azeotropic concentration limit (with improved process flexibility). High-resolution transmission electron microscopy, thermo-gravimetry, Raman spectroscopy and X-ray photoemission spectroscopy systematic analyses are carried out on pristine and oxidized nanotubes in order to assess their functionalization degree, surface chemistry and structural evolution. The most relevant finding of this preliminary study is that the nanotube functionalization extent increases linearly with the HNO{sub 3} vapor concentration.

  18. Phosphoryl-rich flame-retardant ions (FRIONs): towards safer lithium-ion batteries.

    Science.gov (United States)

    Rectenwald, Michael F; Gaffen, Joshua R; Rheingold, Arnold L; Morgan, Alexander B; Protasiewicz, John D

    2014-04-14

    The functionalized catecholate, tetraethyl (2,3-dihydroxy-1,4-phenylene)bis(phosphonate) (H2 -DPC), has been used to prepare a series of lithium salts Li[B(DPC)(oxalato)], Li[B(DPC)2], Li[B(DPC)F2], and Li[P(DPC)3]. The phosphoryl-rich character of these anions was designed to impart flame-retardant properties for their use as potential flame-retardant ions (FRIONs), additives, or replacements for other lithium salts for safer lithium-ion batteries. The new materials were fully characterized, and the single-crystal structures of Li[B(DPC)(oxalato)] and Li[P(DPC)3] have been determined. Thermogravimetric analysis of the four lithium salts show that they are thermally stable up to around 200 °C. Pyrolysis combustion flow calorimetry reveals that these salts produce high char yields upon combustion. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Cleaning Process Development for Metallic Additively Manufactured Parts

    Science.gov (United States)

    Tramel, Terri L.; Welker, Roger; Lowery, Niki; Mitchell, Mark

    2014-01-01

    Additive Manufacturing of metallic components for aerospace applications offers many advantages over traditional manufacturing techniques. As a new technology, many aspects of its widespread utilization remain open to investigation. Among these are the cleaning processes that can be used for post finishing of parts and measurements to verify effectiveness of the cleaning processes. Many cleaning and drying processes and measurement methods that have been used for parts manufactured using conventional techniques are candidates that may be considered for cleaning and verification of additively manufactured parts. Among these are vapor degreasing, ultrasonic immersion and spray cleaning, followed by hot air drying, vacuum baking and solvent displacement drying. Differences in porosity, density, and surface finish of additively manufactured versus conventionally manufactured parts may introduce new considerations in the selection of cleaning and drying processes or the method used to verify their effectiveness. This presentation will review the relative strengths and weaknesses of different candidate cleaning and drying processes as they may apply to additively manufactured metal parts for aerospace applications. An ultrasonic cleaning technique for exploring the cleanability of parts will be presented along with an example using additively manufactured Inconel 718 test specimens to illustrate its use. The data analysis shows that this ultrasonic cleaning approach results in a well-behaved ultrasonic cleaning/extraction behavior. That is, it does not show signs of accelerated cavitation erosion of the base material, which was later confirmed by neutron imaging. In addition, the analysis indicated that complete cleaning would be achieved by ultrasonic immersion cleaning at approximately 5 minutes, which was verified by subsequent cleaning of additional parts.

  20. Military men and sexual practices: Discourses of 'othering' in safer ...

    African Journals Online (AJOL)

    Military men and sexual practices: Discourses of 'othering' in safer sex in the light of HIV/AIDS. ... Military men are particularly vulnerable to HIV because of their working conditions; for example, working far from home and being among communities where they have greater economic and political power, as well as in relation ...

  1. The e-Safer Suffolk Cybersurvey 2012-2013 Summary Report

    OpenAIRE

    Bond, E; Carter, P J; Youthworks Consulting Ltd.; Suffolk County Council; University Campus Suffolk; Suffolk Children's Trust Partnership

    2013-01-01

    This research by Dr Emma Bond and Dr Pelham Carter at UCS, funded by the Suffolk Children’s Trust and commissioned by Suffolk’s E-Safer Strategy investigated the Cyberbullying experiences by young people in Suffolk. The study undertaken between September – November in 2012 was based on an online questionnaire, administered by Youthworks Consulting Ltd, which examined the responses of 2,838 young people in Suffolk.

  2. The urban dilemma: how to make cities safer | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2015-10-01

    Oct 1, 2015 ... ... and inequalities, and identify which programs work – and which don't – to prevent and reduce violence in cities. Read the blog post. Learn more from the baseline study, Researching the Urban Dilemma. Find out more about how IDRC supports research to make cities safer through our partnership – Safe ...

  3. TNO moving forward ... to a safer, cleaner and more efficient mobility

    NARCIS (Netherlands)

    Bleijenberg, A.N.

    2008-01-01

    This book provides an impression of how we are contributing to cleaner, safer and more efficient mobility in Europe, helping our customers from concept to implementation and from engineering solutions to strategic advice. Our knowledge is derived to a significant extent from European research

  4. In-situ acoustic signature monitoring in additive manufacturing processes

    Science.gov (United States)

    Koester, Lucas W.; Taheri, Hossein; Bigelow, Timothy A.; Bond, Leonard J.; Faierson, Eric J.

    2018-04-01

    Additive manufacturing is a rapidly maturing process for the production of complex metallic, ceramic, polymeric, and composite components. The processes used are numerous, and with the complex geometries involved this can make quality control and standardization of the process and inspection difficult. Acoustic emission measurements have been used previously to monitor a number of processes including machining and welding. The authors have identified acoustic signature measurement as a potential means of monitoring metal additive manufacturing processes using process noise characteristics and those discrete acoustic emission events characteristic of defect growth, including cracks and delamination. Results of acoustic monitoring for a metal additive manufacturing process (directed energy deposition) are reported. The work investigated correlations between acoustic emissions and process noise with variations in machine state and deposition parameters, and provided proof of concept data that such correlations do exist.

  5. Sexually active older Australian's knowledge of sexually transmitted infections and safer sexual practices.

    Science.gov (United States)

    Lyons, Anthony; Heywood, Wendy; Fileborn, Bianca; Minichiello, Victor; Barrett, Catherine; Brown, Graham; Hinchliff, Sharron; Malta, Sue; Crameri, Pauline

    2017-06-01

    Rates of sexually transmitted infections (STIs) are rising among older Australians. We conducted a large survey of older people's knowledge of STIs and safer sexual practices. A total of 2,137 Australians aged 60 years and older completed the survey, which included 15 questions assessing knowledge of STIs and safer sexual practices. We examined both levels of knowledge and factors associated with an overall knowledge score. In total, 1,652 respondents reported having sex in the past five years and answered all knowledge questions. This group had good general knowledge but poorer knowledge in areas such as the protection offered by condoms and potential transmission modes for specific STIs. Women had better knowledge than men. Men in their 60s, men with higher education levels, and men who thought they were at risk of STIs reported better knowledge than other men. Knowledge was also better among men and women who had been tested for STIs or reported 'other' sources of knowledge on STIs. Many older Australians lack knowledge of STIs and safer sexual practices. Implications for public health: To reverse current trends toward increasing STI diagnoses in this population, policies and education campaigns aimed at improving knowledge levels may need to be considered. © 2017 The Authors.

  6. Building social capital in healthcare organizations: thinking ecologically for safer care.

    Science.gov (United States)

    Hofmeyer, Anne; Marck, Patricia B

    2008-01-01

    Research on patient safety and health human resources, 2 critical issues for 21st century healthcare, converges on similar findings. Specifically, it is apparent that along with the patients, families, and communities we serve, nurses and other healthcare professionals navigate a volatile health care system where persistent restructuring, market pressures, and workforce instability present ongoing threats to the delivery of safer care. Drawing from the fields of nursing, healthcare ethics, health systems management, and ecological restoration, we outline the role of social capital for organizational integrity, healthy workplace cultures, sustainable resource management, improved nurse retention, effective knowledge translation, and safer patient care. Nursing leaders can use ecological thinking to build the vital resource of social capital by taking concrete steps to commit the necessary human and material resources to: (1) forge relations to foster bonding, bridging and linking social capital; (2) build solidarity and trust; (3) foster collective action and cooperation; (4) strengthen communication and knowledge exchange; and (5) create capacity for social cohesion and inclusion.

  7. An application of safer for the Upper East Fork Poplar Creek characterization area at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    Lutz, C.T.; Provost, C.A.

    1996-01-01

    The Streamlined Approach for Environmental Restoration (SAFER) has been applied at the US Department of Energy's Y-12 Plant in Oak Ridge, Tennessee. The Y-12 Plant is an operationally and hydrogeologically complex area located within the watershed of Upper East Fork Poplar Creek (UEFPC). The plant has been in operation since 1943 and nearly 175 potentially contaminated sites resulting from past waste management practices have been identified. The need to complete Remedial Investigations (RIs) for the sites in a timely and cost-effective manner has resulted in an approach that considers the entire watershed of UEFPC, which has been designated a open-quotes Characterization Areaclose quotes (CA). This approach emphasizes the watershed rather than individual sites, focuses on key questions and issues, and maximizes the use of existing data. The goal of this approach is to focus work toward the resolution of key questions and decisions necessary to complete the remediation of the CA. An evaluation of the potentially contaminated sites, the development of key questions, and the compilation and analysis of existing data are progressing. A SAFER workshop will be held in 1996, which will allow the project team and stakeholders to discuss the status of the RI, identify additional key questions and issues, and determine the activities necessary to complete the RI. This investigation demonstrates an approach to streamlining the RI process that could be applied successfully to other complex sites

  8. kNOw Fear: Making rural public spaces safer for women and girls ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2018-05-01

    May 1, 2018 ... kNOw Fear: Making rural public spaces safer for women and girls ... The International Centre for Research on Women (ICRW) conducts research ... Poonam Kathuria's 17 years of experience as a women's rights advocate is ...

  9. NanoSafer vs. 1.1 - Nanomaterial risk assessment using first order modeling

    DEFF Research Database (Denmark)

    Jensen, Keld A.; Saber, Anne T.; Kristensen, Henrik V.

    2013-01-01

    Currently, there are no nanospecific safety data sheets (SDS) fo r manufactured nanomaterials (MN) and there is only limited data available on nanomaterial exposure levels. We have established an advanced control banding tool, NanoSafer, which enables alternative risk assessm ent and guidance...... in the SDS for the closest analogue bulk material for which the requested occupational exposure limit (OEL) is given as well. The emission potential is either given by a constant release rate or the dustiness level determined us ing the EN15051 rotating drum or similar. The exposure assessment is estimated...... of the nearest analogue bulk material a nd the specific surface area. The NanoSafer control banding tool is now available in Danish and English and contains help tools, including a data library with dustiness data and an inspirational nanosafety e learning tool for companies’ risk management. The ability...

  10. Achieving Safety: Safer Sex, Communication, and Desire among Young Gay Men

    Science.gov (United States)

    Eisenberg, Anna; Bauermeister, Jose A.; Pingel, Emily; Johns, Michelle Marie; Santana, Matthew Leslie

    2011-01-01

    Conceptualizations of safer sex practices among young gay men (YGM) are frequently structured around communication between partners and the subsequent utilization or absence of condoms in a sexual encounter. Drawing on a sample of 34 in-depth interviews with YGM, ages 18 to 24, the authors explore the ways in which conceptualizations and…

  11. Married women's negotiation for safer sexual intercourse in Kenya: Does experience of female genital mutilation matter?

    Science.gov (United States)

    Chai, Xiangnan; Sano, Yujiro; Kansanga, Moses; Baada, Jemima; Antabe, Roger

    2017-12-01

    Married women's ability to negotiate for safer sex is important for HIV prevention in sub-Saharan Africa, including Kenya. Yet, its relationship to female genital mutilation is rarely explored, although female genital mutilation has been described as a social norm and marker of womanhood that can control women's sexuality. Drawing on the social normative influence theory, this study addressed this void in the literature. We analysed data from the 2014 Kenya Demographic and Health Survey using logistic regression. Our sample included 8,602 married women. Two indicators of safer sex, namely the ability to refuse sex and the ability to ask for condom use, were explored. We found that women who had undergone genital mutilation were significantly less likely to report that they can refuse sex (OR=0.87; p<.05) and that they can ask for condom use during sexual intercourse (OR=0.62; p<.001) than their counterparts who had not undergone genital mutilation, while controlling for theoretically relevant variables. Our findings indicate that the experience of female genital mutilation may influence married women's ability to negotiate for safer sex through gendered socialization and expectations. Based on these findings, several policy implications are suggested. For instance, culturally sensitive programmes are needed that target both married women who have undergone genital mutilation and their husbands to understand the importance of safer sexual practices within marriage. Copyright © 2017. Published by Elsevier B.V.

  12. Toxic release consequence analysis tool (TORCAT) for inherently safer design plant

    International Nuclear Information System (INIS)

    Shariff, Azmi Mohd; Zaini, Dzulkarnain

    2010-01-01

    Many major accidents due to toxic release in the past have caused many fatalities such as the tragedy of MIC release in Bhopal, India (1984). One of the approaches is to use inherently safer design technique that utilizes inherent safety principle to eliminate or minimize accidents rather than to control the hazard. This technique is best implemented in preliminary design stage where the consequence of toxic release can be evaluated and necessary design improvements can be implemented to eliminate or minimize the accidents to as low as reasonably practicable (ALARP) without resorting to costly protective system. However, currently there is no commercial tool available that has such capability. This paper reports on the preliminary findings on the development of a prototype tool for consequence analysis and design improvement via inherent safety principle by utilizing an integrated process design simulator with toxic release consequence analysis model. The consequence analysis based on the worst-case scenarios during process flowsheeting stage were conducted as case studies. The preliminary finding shows that toxic release consequences analysis tool (TORCAT) has capability to eliminate or minimize the potential toxic release accidents by adopting the inherent safety principle early in preliminary design stage.

  13. A safer alternative: Cannabis substitution as harm reduction.

    Science.gov (United States)

    Lau, Nicholas; Sales, Paloma; Averill, Sheigla; Murphy, Fiona; Sato, Sye-Ok; Murphy, Sheigla

    2015-11-01

    Substitution is operationalised as a conscious choice made by users to use one drug instead of, or in conjunction with another based on: perceived safety, level of addiction potential, effectiveness in relieving symptoms, access and level of acceptance. Harm reduction is a set of strategies that aim to minimise problems associated with drug use while recognising that for some users, abstinence may be neither a realistic nor a desirable goal. In this paper, we aim for deeper understandings of older adult cannabis users' beliefs and substitution practices as part of the harm reduction framework. We present selected findings from our qualitative study of Baby Boomer (born 1946-1964) marijuana users in the San Francisco Bay Area. Although the sample consisted of primary cannabis users, many had personal experience with other drugs throughout their lifetimes. Data collection consisted of an audio-recorded, semi-structured in-depth life history interview followed by a questionnaire and health survey. Qualitative interviews were analysed to discover users' harm reduction beliefs and cannabis substitution practices. Study participants described using cannabis as a safer alternative for alcohol, illicit drugs and pharmaceuticals based on their perceptions of less adverse side effects, low-risk for addiction and greater effectiveness at relieving symptoms, such as chronic pain. Cannabis substitution can be an effective harm reduction method for those who are unable or unwilling to stop using drugs completely. More research is needed on cannabis as a safer alternative. © 2015 Australasian Professional Society on Alcohol and other Drugs.

  14. Process chain modeling and selection in an additive manufacturing context

    DEFF Research Database (Denmark)

    Thompson, Mary Kathryn; Stolfi, Alessandro; Mischkot, Michael

    2016-01-01

    This paper introduces a new two-dimensional approach to modeling manufacturing process chains. This approach is used to consider the role of additive manufacturing technologies in process chains for a part with micro scale features and no internal geometry. It is shown that additive manufacturing...... evolving fields like additive manufacturing....

  15. Fundamental Aspects of Selective Melting Additive Manufacturing Processes

    Energy Technology Data Exchange (ETDEWEB)

    van Swol, Frank B. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Miller, James E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-12-01

    Certain details of the additive manufacturing process known as selective laser melting (SLM) affect the performance of the final metal part. To unleash the full potential of SLM it is crucial that the process engineer in the field receives guidance about how to select values for a multitude of process variables employed in the building process. These include, for example, the type of powder (e.g., size distribution, shape, type of alloy), orientation of the build axis, the beam scan rate, the beam power density, the scan pattern and scan rate. The science-based selection of these settings con- stitutes an intrinsically challenging multi-physics problem involving heating and melting a metal alloy, reactive, dynamic wetting followed by re-solidification. In addition, inherent to the process is its considerable variability that stems from the powder packing. Each time a limited number of powder particles are placed, the stacking is intrinsically different from the previous, possessing a different geometry, and having a different set of contact areas with the surrounding particles. As a result, even if all other process parameters (scan rate, etc) are exactly the same, the shape and contact geometry and area of the final melt pool will be unique to that particular configuration. This report identifies the most important issues facing SLM, discusses the fundamental physics associated with it and points out how modeling can support the additive manufacturing efforts.

  16. Perspectives of healthcare providers and HIV-affected individuals and couples during the development of a Safer Conception Counseling Toolkit in Kenya: stigma, fears, and recommendations for the delivery of services.

    Science.gov (United States)

    Mmeje, Okeoma; Njoroge, Betty; Akama, Eliud; Leddy, Anna; Breitnauer, Brooke; Darbes, Lynae; Brown, Joelle

    2016-01-01

    Reproduction is important to many HIV-affected individuals and couples and healthcare providers (HCPs) are responsible for providing resources to help them safely conceive while minimizing the risk of sexual and perinatal HIV transmission. In order to fulfill their reproductive goals, HIV-affected individuals and their partners need access to information regarding safer methods of conception. The objective of this qualitative study was to develop a Safer Conception Counseling Toolkit that can be used to train HCPs and counsel HIV-affected individuals and couples in HIV care and treatment clinics in Kenya. We conducted a two-phased qualitative study among HCPs and HIV-affected individuals and couples from eight HIV care and treatment sites in Kisumu, Kenya. We conducted in-depth interviews (IDIs) and focus group discussions (FGDs) to assess the perspectives of HCPs and HIV-affected individuals and couples in order to develop and refine the content of the Toolkit. Subsequently, IDIs were conducted among HCPs who were trained using the Toolkit and FGDs among HIV-affected individuals and couples who were counseled with the Toolkit. HIV-related stigma, fears, and recommendations for delivery of safer conception counseling were assessed during the discussions. One hundred and six individuals participated in FGDs and IDIs; 29 HCPs, 49 HIV-affected women and men, and 14 HIV-serodiscordant couples. Participants indicated that a safer conception counseling and training program for HCPs is needed and that routine provision of safer conception counseling may promote maternal and child health by enhancing reproductive autonomy among HIV-affected couples. They also reported that the Toolkit may help dispel the stigma and fears associated with reproduction in HIV-affected couples, while supporting them in achieving their reproductive goals. Additional research is needed to evaluate the Safer Conception Toolkit in order to support its implementation and use in HIV care and

  17. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 539: Area 25 and Area 26 Railroad Tracks, Nevada Test Site, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Mark Krauss

    2010-06-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 539, Areas 25 and 26 Railroad Tracks, as identified in the Federal Facility Agreement and Consent Order (FFACO). A modification to the FFACOwas approved in May 2010 to transfer the two Railroad Tracks corrective action sites (CASs) from CAU 114 into CAU539. The two CASs are located in Areas 25 and 26 of the Nevada Test Site: • 25-99-21, Area 25 Railroad Tracks • 26-99-05, Area 26 Railroad Tracks This plan provides the methodology for field activities needed to gather the necessary information for closing the two CASs. There is sufficient information and process knowledge from historical documentation and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of the CAU 539 Railroad Tracks CASs using the SAFER process. Additional information will be obtained by conducting a field investigation before selecting the appropriate corrective action for each CAS. The results of the field investigation should support a defensible recommendation that no further corrective action is necessary. If it is determined that complete clean closure cannot be accomplished during the SAFER, then a hold point will have been reached and the Nevada Division of Environmental Protection (NDEP) will be consulted to determine whether the remaining contamination will be closed under the alternative corrective action of closure in place with use restrictions. This will be presented in a closure report that will be prepared and submitted to the NDEP for review and approval. The sites will be investigated based on the data quality objectives (DQOs) developed on December 14, 2009, by representatives of U.S.Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office; Navarro Nevada Environmental Services, LLC (NNES); and National Security Technologies

  18. Cerus process modified with glass addition (Vitrocerus)

    International Nuclear Information System (INIS)

    Arboleda, P.A.; Rodriguez, D.S.; Prado, M.O.

    2009-01-01

    A processing method for spent fuels type Mtr from research reactors has developed in Nuclear Materials Division of Bariloche Atomic Center, this process involved the creation of ceramic matrix containing fuel and natural uranium in an isotopic solution, this project has named CERUS (Spanish acronym of 'Ceramización de Elementos Radioactivos en Uranio Sinterizado': Ceramming of radioactive elements with sintered uranium ). This process works with reduced volumes than a conventional vitrification, however because of some issues on the material resistance; we propose the addition of small amounts of glass with the idea to enhance the lixiviation properties of the final material. In this process is not considered the reprocessing possibility of the spent fuel. (author)

  19. On the record process of time-reversible spectrally-negative Markov additive processes

    NARCIS (Netherlands)

    J. Ivanovs; M.R.H. Mandjes (Michel)

    2009-01-01

    htmlabstractWe study the record process of a spectrally-negative Markov additive process (MAP). Assuming time-reversibility, a number of key quantities can be given explicitly. It is shown how these key quantities can be used when analyzing the distribution of the all-time maximum attained by MAPs

  20. Electronic cigarettes: a safer alternative or potential poison?

    Science.gov (United States)

    Smith, Janet E

    2014-10-01

    Electronic cigarettes have been marketed as a safer alternative to cigarettes, and their use is expanding exponentially. However, there is a severe lack of scientific data about the ingredients in the liquid used in the device and the health consequences of using electronic cigarettes. As technology has outpaced regulations, the production and sale of electronic cigarettes are, as yet, unregulated and do not fall under the purview of the Food and Drug Administration. This article will review the mechanism of action and what is currently known about the safety of electronic cigarettes. The risk of poisoning for children will also be identified, as well as the implications for home healthcare clinicians.

  1. An open framework for automated chemical hazard assessment based on GreenScreen for Safer Chemicals: A proof of concept.

    Science.gov (United States)

    Wehage, Kristopher; Chenhansa, Panan; Schoenung, Julie M

    2017-01-01

    GreenScreen® for Safer Chemicals is a framework for comparative chemical hazard assessment. It is the first transparent, open and publicly accessible framework of its kind, allowing manufacturers and governmental agencies to make informed decisions about the chemicals and substances used in consumer products and buildings. In the GreenScreen® benchmarking process, chemical hazards are assessed and classified based on 18 hazard endpoints from up to 30 different sources. The result is a simple numerical benchmark score and accompanying assessment report that allows users to flag chemicals of concern and identify safer alternatives. Although the screening process is straightforward, aggregating and sorting hazard data is tedious, time-consuming, and prone to human error. In light of these challenges, the present work demonstrates the usage of automation to cull chemical hazard data from publicly available internet resources, assign metadata, and perform a GreenScreen® hazard assessment using the GreenScreen® "List Translator." The automated technique, written as a module in the Python programming language, generates GreenScreen® List Translation data for over 3000 chemicals in approximately 30 s. Discussion of the potential benefits and limitations of automated techniques is provided. By embedding the library into a web-based graphical user interface, the extensibility of the library is demonstrated. The accompanying source code is made available to the hazard assessment community. Integr Environ Assess Manag 2017;13:167-176. © 2016 SETAC. © 2016 SETAC.

  2. Pathwise duals of monotone and additive Markov processes

    Czech Academy of Sciences Publication Activity Database

    Sturm, A.; Swart, Jan M.

    -, - (2018) ISSN 0894-9840 R&D Projects: GA ČR GAP201/12/2613 Institutional support: RVO:67985556 Keywords : pathwise duality * monotone Markov process * additive Markov process * interacting particle system Subject RIV: BA - General Mathematics Impact factor: 0.854, year: 2016 http://library.utia.cas.cz/separaty/2016/SI/swart-0465436.pdf

  3. Additive Manufacturing: Multi Material Processing and Part Quality Control

    DEFF Research Database (Denmark)

    Pedersen, David Bue

    This Ph.D dissertation,ffAdditive Manufacturing: Multi Material Processing and Part Quality Controlff, deal with Additive Manufacturing technologies which is a common name for a series of processes that are recognized by being computer controlled, highly automated, and manufacture objects...... by a layered deposition of material. Two areas of particular interest is addressed. They are rooted in two very different areas, yet is intended to fuel the same goal. To help Additive Manufacturing technologies one step closer to becoming the autonomous, digital manufacturing method of tomorrow. Vision...... systems A paradox exist in the field of Additive Manufacturing. The technologies allow for close-to unrestrained and integral geometrical freedom. Almost any geometry can be manufactured fast, e"ciently and cheap. Something that has been missing fundamental capability since the entering of the industrial...

  4. Advanced and safer lithium-ion battery based on sustainable electrodes

    KAUST Repository

    Ding, Xiang

    2018-02-17

    Seeking advanced and safer lithium-ion battery with sustainable characteristic is significant for the development of electronic devices and electric vehicles. Herein, a new porous TiO nanobundles (PTNBs) is synthesized though a scalable and green hydrothermal strategy from the TiO powders without using any high-cost and harmful organic titanium-based compounds. The PTNBs exhibits an extremely high lithium storage capacity of 296 mAh g at 100 mA g, where the capacity can maintain over 146 mAh g even after 500 cycles at 1000 mA g. To pursue more reliable Li-ion batteries, full batteries of PTNBs/LiNiMnO (x = 0, 0.5) using spinel structured cathode are constructed. The batteries have the features of sustainability and deliver high capacities of 112 mAh g and 102 mAh g with stable capacity retentions of 99% and 90% over 140 cycles. Note that the energy densities can achieve as high as 267 and 270 Wh kg (535 and 540 Wh kg ) respectively, which is feasible to satisfy diverse requirements for energy storage products. We believe that the universal synthetic strategy, appealing structure and intriguing properties of PTNBs is applicable for wider applications, while the concept of sustainable strategy seeking reliable and safer Li-ion battery can attract broad interest.

  5. Advanced and safer lithium-ion battery based on sustainable electrodes

    Science.gov (United States)

    Ding, Xiang; Huang, Xiaobing; Jin, Junling; Ming, Hai; Wang, Limin; Ming, Jun

    2018-03-01

    Seeking advanced and safer lithium-ion battery with sustainable characteristic is significant for the development of electronic devices and electric vehicles. Herein, a new porous TiO2 nanobundles (PTNBs) is synthesized though a scalable and green hydrothermal strategy from the TiO2 powders without using any high-cost and harmful organic titanium-based compounds. The PTNBs exhibits an extremely high lithium storage capacity of 296 mAh g-1 at 100 mA g-1, where the capacity can maintain over 146 mAh g-1 even after 500 cycles at 1000 mA g-1. To pursue more reliable Li-ion batteries, full batteries of PTNBs/LiNixMn1-xO4 (x = 0, 0.5) using spinel structured cathode are constructed. The batteries have the features of sustainability and deliver high capacities of 112 mAh gcathode-1 and 102 mAh gcathode-1 with stable capacity retentions of 99% and 90% over 140 cycles. Note that the energy densities can achieve as high as 267 and 270 Wh kgcathode-1 (535 and 540 Wh kganode-1) respectively, which is feasible to satisfy diverse requirements for energy storage products. We believe that the universal synthetic strategy, appealing structure and intriguing properties of PTNBs is applicable for wider applications, while the concept of sustainable strategy seeking reliable and safer Li-ion battery can attract broad interest.

  6. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 538: Spill Sites, Nevada Test Site, Nevada, Rev. No.: 0

    Energy Technology Data Exchange (ETDEWEB)

    Alfred Wickline

    2006-04-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions necessary for the closure of Corrective Action Unit (CAU) 538: Spill Sites, Nevada Test Site, Nevada. It has been developed in accordance with the ''Federal Facility Agreement and Consent Order'' (FFACO) (1996) that was agreed to by the State of Nevada, the U.S. Department of Energy (DOE), and the U.S. Department of Defense. A SAFER may be performed when the following criteria are met: (1) Conceptual corrective actions are clearly identified (although some degree of investigation may be necessary to select a specific corrective action before completion of the Corrective Action Investigation [CAI]). (2) Uncertainty of the nature, extent, and corrective action must be limited to an acceptable level of risk. (3) The SAFER Plan includes decision points and criteria for making data quality objective (DQO) decisions. The purpose of the investigation will be to document and verify the adequacy of existing information; to affirm the decision for either clean closure, closure in place, or no further action; and to provide sufficient data to implement the corrective action. The actual corrective action selected will be based on characterization activities implemented under this SAFER Plan. This SAFER Plan identifies decision points developed in cooperation with the Nevada Division of Environmental Protection (NDEP) and where DOE will reach consensus with NDEP before beginning the next phase of work.

  7. Topology Optimization for Reducing Additive Manufacturing Processing Distortions

    Science.gov (United States)

    2017-12-01

    distribution is unlimited. 1. Introduction Additive manufacturing (AM) is a production method that involves gradual, layer- by-layer building of material... design space—allowing the production of pre- viously unmanufacturable topologically optimized structures—constraints remain. One constraint, for...ARL-TR-8242•DEC 2017 US Army Research Laboratory Topology Optimization for ReducingAdditive Manufacturing ProcessingDistortions by Raymond A Wildman

  8. Remedial technology and characterization development at the SRS F/H Retention Basins using the DOE SAFER methodology

    International Nuclear Information System (INIS)

    Miles, W.C. Jr.; Kuelske, K.J.

    1994-01-01

    The Streamlined Approach For Environmental Restoration (SAFER) is a strategy used to accelerate and improve the environmental assessment and remediation of the F/H Retention Basins at the Savannah River Site (SRS). TMs strategy combines the data quality objectives (DQO) process and the observational approach to focus on data collection and converge on a remedial action early. This approach emphasizes stakeholder involvement throughout the Remedial Investigation/Feasibility Study (RI/FS) process. The SAFER methodology is being applied to the characterization, technology development, and remediation tasks for the F/H Retention Basins. This ''approach was initiated in the scoping phase of these projects through the involvment of major stakeholders; Department of Energy (DOE)-Savannah River Field Office, DOE-Headquarters, Westinghouse Savannah River Company, United States Environmental Protection Agency (EPA) Region IV, and the state of South Carolina Department of Health and Environmental Control (SCDHEC), in the development of the Remedial Investigation (RI) workplans. A major activity that has been initiated is the development and implementation of a phase I workplan to identify preliminary contaminants of concern (pCOCs). A sampling plan was developed and approved by the major stakeholders for preliminary characterization of wastes remaining in the F/H Retention Basins. The involvement of stakeholders, development of a site conceptual model, development of remedial objectives for probable conditions, identification of the problem and reasonable deviations, and development of initial decision rules in the planning stages will ensure that preliminary data needs are identified and obtained prior to the initiation of the assessment and implementation phases of the projects resulting in the final remediation of the sites in an accelerated and more cost effective manner

  9. Process development for green part printing using binder jetting additive manufacturing

    Science.gov (United States)

    Miyanaji, Hadi; Orth, Morgan; Akbar, Junaid Muhammad; Yang, Li

    2018-05-01

    Originally developed decades ago, the binder jetting additive manufacturing (BJ-AM) process possesses various advantages compared to other additive manufacturing (AM) technologies such as broad material compatibility and technological expandability. However, the adoption of BJ-AM has been limited by the lack of knowledge with the fundamental understanding of the process principles and characteristics, as well as the relatively few systematic design guideline that are available. In this work, the process design considerations for BJ-AM in green part fabrication were discussed in detail in order to provide a comprehensive perspective of the design for additive manufacturing for the process. Various process factors, including binder saturation, in-process drying, powder spreading, powder feedstock characteristics, binder characteristics and post-process curing, could significantly affect the printing quality of the green parts such as geometrical accuracy and part integrity. For powder feedstock with low flowability, even though process parameters could be optimized to partially offset the printing feasibility issue, the qualities of the green parts will be intrinsically limited due to the existence of large internal voids that are inaccessible to the binder. In addition, during the process development, the balanced combination between the saturation level and in-process drying is of critical importance in the quality control of the green parts.

  10. In-Process Monitoring of Additive Manufacturing, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The key innovation in this project is the implementation of an Imaging Fourier Transform Spectrometer (IFTS) for in situ metal additive manufacturing process...

  11. Biocompatibility of hydroxyapatite scaffolds processed by lithography-based additive manufacturing.

    Science.gov (United States)

    Tesavibul, Passakorn; Chantaweroad, Surapol; Laohaprapanon, Apinya; Channasanon, Somruethai; Uppanan, Paweena; Tanodekaew, Siriporn; Chalermkarnnon, Prasert; Sitthiseripratip, Kriskrai

    2015-01-01

    The fabrication of hydroxyapatite scaffolds for bone tissue engineering applications by using lithography-based additive manufacturing techniques has been introduced due to the abilities to control porous structures with suitable resolutions. In this research, the use of hydroxyapatite cellular structures, which are processed by lithography-based additive manufacturing machine, as a bone tissue engineering scaffold was investigated. The utilization of digital light processing system for additive manufacturing machine in laboratory scale was performed in order to fabricate the hydroxyapatite scaffold, of which biocompatibilities were eventually evaluated by direct contact and cell-culturing tests. In addition, the density and compressive strength of the scaffolds were also characterized. The results show that the hydroxyapatite scaffold at 77% of porosity with 91% of theoretical density and 0.36 MPa of the compressive strength are able to be processed. In comparison with a conventionally sintered hydroxyapatite, the scaffold did not present any cytotoxic signs while the viability of cells at 95.1% was reported. After 14 days of cell-culturing tests, the scaffold was able to be attached by pre-osteoblasts (MC3T3-E1) leading to cell proliferation and differentiation. The hydroxyapatite scaffold for bone tissue engineering was able to be processed by the lithography-based additive manufacturing machine while the biocompatibilities were also confirmed.

  12. Biological features produced by additive manufacturing processes using vat photopolymerization method

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Mendez Ribo, Macarena; Pedersen, David Bue

    2017-01-01

    of micro biological features by Additive Manufacturing (AM) processes. The study characterizes the additive manufacturing processes for polymeric micro part productions using the vat photopolymerization method. A specifically designed vat photopolymerization AM machine suitable for precision printing...

  13. A Safer and Convenient Synthesis of Sulfathiazole for Undergraduate Organic and Medicinal Chemistry Classes

    Science.gov (United States)

    Boyle, Jeff; Otty, Sandra; Sarojini, Vijayalekshmi

    2012-01-01

    A safer method for the synthesis of the sulfonamide drug sulfathiazole, for undergraduate classes, is described. This method improves upon procedures currently followed in several undergraduate teaching laboratories for the synthesis of sulfathiazole. Key features of this procedure include the total exclusion of pyridine, which has potential…

  14. Seriously Mentally Ill Women's Safer Sex Behaviors and the Theory of Reasoned Action

    Science.gov (United States)

    Randolph, Mary E.; Pinkerton, Steven D.; Somlai, Anton M.; Kelly, Jeffrey A.; McAuliffe, Timothy L.; Gibson, Richard H.; Hackl, Kristin

    2009-01-01

    Seriously mentally ill women at risk for HIV infection (n = 96) participated in structured interviews assessing sexual and substance-use behavior over a 3-month period. The majority of the women (63.5%) did not use condoms. Consistent with the theory of reasoned action, attitudes toward condom use and perceived social norms about safer sex were…

  15. Additive Manufacturing of High-Entropy Alloys by Laser Processing

    NARCIS (Netherlands)

    Ocelik, V.; Janssen, Niels; Smith, Stefan; De Hosson, J. Th M.

    This contribution concentrates on the possibilities of additive manufacturing of high-entropy clad layers by laser processing. In particular, the effects of the laser surface processing parameters on the microstructure and hardness of high-entropy alloys (HEAs) were examined. AlCoCrFeNi alloys with

  16. Urban Vulnerability in Bantul District, Indonesia—Towards Safer and Sustainable Development

    Directory of Open Access Journals (Sweden)

    R. Rijanta

    2012-08-01

    Full Text Available Assuring safer and sustainable development in seismic prone areas requires predictive measurements, i.e., hazard, vulnerability and risk assessment. This research aims to assess urban vulnerability due to seismic hazard through a risk based spatial plan. The idea is to indicate current and future potential losses due to specified hazards with given spatial and temporal units. Herein, urban vulnerability refers to the classic separation between social and physical vulnerability assessments. The research area covers six sub-districts in Bantul, Indonesia. It experienced 6.2 Mw earthquakes on May, 27th, 2006 and suffered a death toll of 5700, economic losses of up to 3.1 billion US$ and damage to nearly 80% of a 508 km2 area. The research area experienced the following regional issues: (1 seismic hazard; (2 rapid land conversion and (3 domination of low-income group. This research employs spatial multi criteria evaluations (SMCE for social vulnerability (SMCE-SV and for physical vulnerability (SMCE-PV. The research reveals that (1 SMCE-SV and SMCE-PV are empirically possible to indicate the urban vulnerability indices; and (2 integrating the urban vulnerability assessment into a spatial plan requires strategic, technical, substantial and procedural integration. In summary, without adequate knowledge and political support, any manifestation towards safer and sustainable development will remain meager and haphazard.

  17. Design of Test Parts to Characterize Micro Additive Manufacturing Processes

    DEFF Research Database (Denmark)

    Thompson, Mary Kathryn; Mischkot, Michael

    2015-01-01

    The minimum feature size and obtainable tolerances of additive manufacturing processes are linked to the smallest volumetric elements (voxels) that can be created. This work presents the iterative design of a test part to investigate the resolution of AM processes with voxel sizes at the micro...... scale. Each design iteration reduces the test part size, increases the number of test features, improves functionality, and decreases coupling in the part. The final design is a set of three test parts that are easy to orient and measure, and that provide useful information about micro additive...... manufacturing processes....

  18. Modelling of additive manufacturing processes: a review and classification

    Science.gov (United States)

    Stavropoulos, Panagiotis; Foteinopoulos, Panagis

    2018-03-01

    Additive manufacturing (AM) is a very promising technology; however, there are a number of open issues related to the different AM processes. The literature on modelling the existing AM processes is reviewed and classified. A categorization of the different AM processes in process groups, according to the process mechanism, has been conducted and the most important issues are stated. Suggestions are made as to which approach is more appropriate according to the key performance indicator desired to be modelled and a discussion is included as to the way that future modelling work can better contribute to improving today's AM process understanding.

  19. Computational Process Modeling for Additive Manufacturing (OSU)

    Science.gov (United States)

    Bagg, Stacey; Zhang, Wei

    2015-01-01

    Powder-Bed Additive Manufacturing (AM) through Direct Metal Laser Sintering (DMLS) or Selective Laser Melting (SLM) is being used by NASA and the Aerospace industry to "print" parts that traditionally are very complex, high cost, or long schedule lead items. The process spreads a thin layer of metal powder over a build platform, then melts the powder in a series of welds in a desired shape. The next layer of powder is applied, and the process is repeated until layer-by-layer, a very complex part can be built. This reduces cost and schedule by eliminating very complex tooling and processes traditionally used in aerospace component manufacturing. To use the process to print end-use items, NASA seeks to understand SLM material well enough to develop a method of qualifying parts for space flight operation. Traditionally, a new material process takes many years and high investment to generate statistical databases and experiential knowledge, but computational modeling can truncate the schedule and cost -many experiments can be run quickly in a model, which would take years and a high material cost to run empirically. This project seeks to optimize material build parameters with reduced time and cost through modeling.

  20. Understanding the resistance to creating safer ice hockey: essential points for injury prevention.

    Science.gov (United States)

    Todd, Ryan A; Soklaridis, Sophie; Treen, Alice K; Bhalerao, Shree U; Cusimano, Michael D

    2017-11-27

    Despite the known negative health outcomes of concussions in minor level boys' hockey, there has been significant resistance to creating a safer game with less body checking. To better understand cultural barriers that prevent making the sport safer for youth and adolescents, semistructured interviews, with 20 ice hockey stakeholders, were conducted and analysed using thematic analysis. Through this analysis, two primary concepts arose from respondents. The first concept is that body checking, despite the harm it can cause, should be done in a respectful sportsmanlike fashion. The second concept is the contradiction that the game of ice hockey is both dynamic and unchangeable. Using structural functionalist theory, we propose an argument that the unfortunate perpetuation of violence and body checking in youth ice hockey serves to maintain the social order of the game and its culture. Any strategies aimed at modifying and promoting healthy behaviour in the game should take these concepts into account. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  1. Technological foundations of processing tomato pomace in feed additives

    Directory of Open Access Journals (Sweden)

    B. Yegorov

    2015-05-01

    Full Text Available Introduction. Search for new types of alternative raw material for the efficient development of poultry industry and problem of waste disposal of canning industry made it necessary to develop a method of processing tomato pomace in feed additives. Materials and methods. Sampling, preparation and testing were carried out by general and specific organ oleptic and physical-technological methods of assessment and analysis of the properties of raw materials and finished products. Results. Incorporation of tomato pomace in the feed additive reduces the cost of raw materials and expenses associated with moistening of the mixture before extrusion and incorporation of chalk feed will solve the problem of calcium imbalance of laying hens. It was found that extrusion process has improved the physical properties of feed additive and showed the possibility of its use as a feed component: moisture content decreased by 34.5 %, the angle of repose increased by 11.4 %, flowability decreased by 39.7 % and bulk density decreased by 32.3 %. Conclusions. The resulting feed additive will solve the problem of diversification of raw materials, waste, calcium imbalance of laying hens and reduce expenses on compound animal feedstuff production.

  2. Irradiation processing of food

    International Nuclear Information System (INIS)

    Anunuso, C.I.

    1988-01-01

    Ionizing radiation is now showing new promise of contributing to the feeding of hungry populations, solving solid and liquid waste disposal problems, providing safer medical supplies, pharmaceuticals, and other commodities, and at the same time reducing energy consumption in industrial processing in general. (author)

  3. SaferNanoDesign Summer School | 13-18 June

    CERN Multimedia

    2016-01-01

    A bioHC Summer School - 13-18 June 2016 - European Scientific Institute, Archamps, Haute-Savoie.   How can industrial innovation in nanotechnologies be reconciled with the legitimate concerns of citizens regarding environmental protection and public health? Tomorrow’s researchers and engineers will require skills in risk evaluation using computational methods of modelling and simulation relevant to nanomaterials. An intensive one-week specialist school, SaferNanoDesign will examine the analytical tools and methodologies required to rise to the challenge of the ecodesign of nanomaterial-enabled technology. The School combines an intensive programme of lecture presentations, followed up by practical sessions (experiments, computer simulation and modelling) and interdisciplinary group work. Courses will be given by international experts from France, Scotland, the US, the Netherlands and Switzerland and representatives from industry and regulatory bodies. For more information: www....

  4. Safer Conception for Couples Affected by HIV: Structural and Cultural Considerations in the Delivery of Safer Conception Care in Uganda.

    Science.gov (United States)

    Mindry, Deborah; Wanyenze, Rhoda K; Beyeza-Kashesya, Jolly; Woldetsadik, Mahlet A; Finocchario-Kessler, Sarah; Goggin, Kathy; Wagner, Glenn

    2017-08-01

    In countries with high HIV prevalence and high fertility desires, the rights of HIV-affected couples to have children are a pressing issue. Conception among people living with HIV carries risks for both horizontal and vertical HIV transmission. In Uganda ~100,000 HIV-infected women become pregnant annually. Providers face a number of challenges to preventing HIV transmission, reducing unplanned pregnancies, and ensuring safer conception. We report findings from interviews with 27 HIV-affected couples (54 individuals) in Uganda. We explored key cultural and structural factors shaping couples' childbearing decisions. Our data reveal a complex intersection of gender norms, familial expectations, relationship dynamics, and HIV stigma influencing their decisions. Participants provided insights regarding provider bias, stigma, and the gendering of reproductive healthcare. To reduce horizontal transmission HIV and family planning clinics must address men's and women's concerns regarding childbearing with specific attention to cultural and structural challenges.

  5. Additive Manufacturing of Tooling for Refrigeration Cabinet Foaming Processes

    Energy Technology Data Exchange (ETDEWEB)

    Post, Brian K [ORNL; Nuttall, David [ORNL; Cukier, Michael Z [ORNL; Hile, Michael B [ORNL

    2016-07-29

    The primary objective of this project was to leverage the Big Area Additive Manufacturing (BAAM) process and materials into a long term, quick change tooling concept to drastically reduce product lead and development timelines and costs. Current refrigeration foam molds are complicated to manufacture involving casting several aluminum parts in an approximate shape, machining components of the molds and post fitting and shimming of the parts in an articulated fixture. The total process timeline can take over 6 months. The foaming process is slower than required for production, therefore multiple fixtures, 10 to 27, are required per refrigerator model. Molds are particular to a specific product configuration making mixed model assembly challenging for sequencing, mold changes or auto changeover features. The initial goal was to create a tool leveraging the ORNL materials and additive process to build a tool in 4 to 6 weeks or less. A secondary goal was to create common fixture cores and provide lightweight fixture sections that could be revised in a very short time to increase equipment flexibility reduce lead times, lower the barriers to first production trials, and reduce tooling costs.

  6. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 465: Hydronuclear Nevada National Security Site, Nevada, with ROTC 1, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Patrick Matthews

    2011-11-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 465, Hydronuclear, identified in the Federal Facility Agreement and Consent Order (FFACO). Corrective Action Unit 465 comprises the following four corrective action sites (CASs) located in Areas 6 and 27 of the Nevada National Security Site: (1) 00-23-01, Hydronuclear Experiment; (2) 00-23-02, Hydronuclear Experiment; (3) 00-23-03, Hydronuclear Experiment; (4) 06-99-01, Hydronuclear. The sites will be investigated based on the data quality objectives (DQOs) developed on July 6, 2011, by representatives of the Nevada Division of Environmental Protection (NDEP) and the U.S. Department of Energy (DOE), National Nuclear Security Administration Nevada Site Office. The DQO process was used to identify and define the type, amount, and quality of data needed to determine and implement appropriate corrective actions for each CAS in CAU 465. For CAU 465, two potential release components have been identified. The subsurface release component includes potential releases of radiological and nonradiological contaminants from the subsurface hydronuclear experiments and disposal boreholes. The surface release component consists of other potential releases of radiological and nonradiological contaminants to surface soils that may have occurred during the pre- and post-test activities. This plan provides the methodology for collection of the necessary information for closing each CAS component. There is sufficient information and process knowledge from historical documentation, contaminant characteristics, existing regional and site groundwater models, and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of CAU 465 using the SAFER process. For potential subsurface releases, flow and transport models will be developed to integrate existing data into a conservative

  7. Towards safer surgery in patients with sickle cell disease

    International Nuclear Information System (INIS)

    Meshikhes, Abdul-Wahed N.

    2007-01-01

    Surgery in patients with sickle cell disease (SCD) has been associated with high morbidity and mortality. In recent years, a marked improvement in the safety of surgery and anesthesia in this high-risk group of patients has been witnessed; owing to the improvements in surgical and anesthetic care, greater awareness of pathophysiology of disease, proper perioperative preparation and attention to factors predisposing to vasoocclusive crises. However, this is not paralleled by similar improvement in countries where the disease is not prevalent. Greater population mobility in recent years makes recognition of surgical manifestations of the disease and awareness of perioperative management of sickle cell patients undergoing surgical interventions of paramount importance. This article aims to summarize steps towards safer surgery in patients with SCD. (author)

  8. Develop and implement preconditioning techniques to control face ejection rockbursts for safer mining in seismically hazardous areas

    CSIR Research Space (South Africa)

    Toper, AZ

    1998-01-01

    Full Text Available This research report discusses the development of preconditioning techniques to control face bursts, for safer mining in seismically hazardous areas. Preconditioning involves regularly setting off carefully tailored blasts in the fractured rock...

  9. Electron beam additive manufacturing with wire - Analysis of the process

    Science.gov (United States)

    Weglowski, Marek St.; Błacha, Sylwester; Pilarczyk, Jan; Dutkiewicz, Jan; Rogal, Łukasz

    2018-05-01

    The electron beam additive manufacturing process with wire is a part of global trend to find fast and efficient methods for producing complex shapes elements from costly metal alloys such as stainless steels, nickel alloys, titanium alloys etc. whose production by other conventional technologies is unprofitable or technically impossible. Demand for additive manufacturing is linked to the development of new technologies in the automotive, aerospace and machinery industries. The aim of the presented work was to carried out research on electron beam additive manufacturing with a wire as a deposited (filler) material. The scope of the work was to investigate the influence of selected technological parameters such as: wire feed rate, beam current, travelling speed, acceleration voltage on stability of the deposition process and geometric dimensions of the padding welds. The research revealed that, at low beam currents, the deposition process is unstable. The padding weld reinforcement is non-uniform. Irregularity of the width, height and straightness of the padding welds can be observed. At too high acceleration voltage and beam current, burn-through of plate and excess penetration weld can be revealed. The achieved results and gained knowledge allowed to produce, based on EBAM with wire process, whole structure from stainless steel.

  10. Soluble salt removal from MSWI fly ash and its stabilization for safer disposal and recovery as road basement material.

    Science.gov (United States)

    Colangelo, F; Cioffi, R; Montagnaro, F; Santoro, L

    2012-06-01

    Fly ash from municipal solid waste incinerators (MSWI) is classified as hazardous in the European Waste Catalogue. Proper stabilization processes should be required before any management option is put into practice. Due to the inorganic nature of MSWI fly ash, cementitious stabilization processes are worthy of consideration. However, the effectiveness of such processes can be severely compromised by the high content of soluble chlorides and sulphates. In this paper, a preliminary washing treatment has been optimized to remove as much as possible soluble salts by employing as little as possible water. Two different operating conditions (single-step and two-step) have been developed to this scope. Furthermore, it has been demonstrated that stabilized systems containing 20% of binder are suitable for safer disposal as well as for material recovery in the field of road basement (cement bound granular material layer). Three commercially available cements (pozzolanic, limestone and slag) have been employed as binders. Copyright © 2012 Elsevier Ltd. All rights reserved.

  11. Acceptability and preferences for safer conception HIV prevention strategies: a qualitative study.

    Science.gov (United States)

    Schwartz, Sheree R; West, Nora; Phofa, Rebecca; Yende, Nompumelelo; Sanne, Ian; Bassett, Jean; Van Rie, Annelies

    2016-10-01

    Safer conception strategies to reduce the HIV transmission risk include antiretroviral therapy for HIV-positive partners, pre-exposure prophylaxis for HIV-negative partners, condomless sex limited to fertile periods, and home-based self-insemination. Resistance to taking treatment or cultural concerns may limit uptake of strategies and intervention success. Understanding the acceptability and preferences between different approaches is important to optimise service delivery. Between February and July 2013, 42 adults (21 HIV-positive and 21 HIV-negative) receiving primary care at Witkoppen Health and Welfare Centre in Johannesburg, South Africa, participated in focus group discussions or in-depth interviews. Themes were analysed using a grounded theory approach. Acceptability of antiretroviral-based strategies varied. Concerns over side effects, antiretroviral treatment duration and beliefs that treatment is only for the sick were common barriers; however, desperation for a child was noted as a facilitator for uptake. HIV-negative men and HIV-positive women had favourable attitudes towards self-insemination, though paternity and safety concerns were raised. Self-insemination was generally preferred over pre-exposure prophylaxis by HIV-negative men, and antiretroviral-based strategies were preferred by couples with HIV-negative female partners, despite concerns raised about condomless sex while virally suppressed. Knowledge about the fertile window was low. A strong counselling component will be required for effective uptake and adherence to safer conception services. © The Author(s) 2016.

  12. New research discovery may mean less radioactive contamination, safer nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Murph, S. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-06-20

    Murph has now made another nanoparticle breakthrough that could benefit various work environments such as nuclear power plants. Murph and her team have created nanoparticle treated stainless steel filters that are capable to capturing radioactive vapor materials. Just like air filters capture dust and dirt, these filters are capable of capturing large amounts of radioactive vapors. The new research may one day mean that nuclear power plant workers, and other workers in related fields, will have a safer working environment.

  13. 15 CFR 713.4 - Advance declaration requirements for additionally planned production, processing, or consumption...

    Science.gov (United States)

    2010-01-01

    ... additionally planned production, processing, or consumption of Schedule 2 chemicals. 713.4 Section 713.4..., processing, or consumption of Schedule 2 chemicals. (a) Declaration requirements for additionally planned activities. (1) You must declare additionally planned production, processing, or consumption of Schedule 2...

  14. Understanding Barriers to Safer Sex Practice in Zimbabwean Marriages: Implications for Future HIV Prevention Interventions

    Science.gov (United States)

    Mugweni, Esther; Omar, Mayeh; Pearson, Stephen

    2015-01-01

    Against the backdrop of high human immunodeficiency virus (HIV) prevalence in stable relationships in Southern Africa, our study presents sociocultural barriers to safer sex practice in Zimbabwean marriages. We conducted 36 in-depth interviews and four focus group discussions with married men and women in Zimbabwe in 2008. Our aim was to identify…

  15. Female gratification, sexual power and safer sex

    DEFF Research Database (Denmark)

    Skafte, Ina; Silberschmidt, Margrethe

    2014-01-01

    The gender-based response to HIV in sub-Saharan Africa has tended to reinforce normative stereotypes of women as subordinated, passive and powerless victims, in particular in sexual relations. However, based on qualitative data from Rwanda, this paper argues that such conceptualisations fail to r...... both to practice safer sex and to access decision-making power and material resources. This suggests that inherent in sexual relations is a potential for the empowerment of women and the transformation of gender relations.......The gender-based response to HIV in sub-Saharan Africa has tended to reinforce normative stereotypes of women as subordinated, passive and powerless victims, in particular in sexual relations. However, based on qualitative data from Rwanda, this paper argues that such conceptualisations fail...... to recognise that while women do comply with prevalent social norms, they also challenge these norms and sex becomes a domain in which they can exert power. Female sexuality and sexual gratification - acknowledged and valued by women as well as men - play a pivotal role in the Rwandese mode of sexual...

  16. Modeling process-structure-property relationships for additive manufacturing

    Science.gov (United States)

    Yan, Wentao; Lin, Stephen; Kafka, Orion L.; Yu, Cheng; Liu, Zeliang; Lian, Yanping; Wolff, Sarah; Cao, Jian; Wagner, Gregory J.; Liu, Wing Kam

    2018-02-01

    This paper presents our latest work on comprehensive modeling of process-structure-property relationships for additive manufacturing (AM) materials, including using data-mining techniques to close the cycle of design-predict-optimize. To illustrate the processstructure relationship, the multi-scale multi-physics process modeling starts from the micro-scale to establish a mechanistic heat source model, to the meso-scale models of individual powder particle evolution, and finally to the macro-scale model to simulate the fabrication process of a complex product. To link structure and properties, a highefficiency mechanistic model, self-consistent clustering analyses, is developed to capture a variety of material response. The model incorporates factors such as voids, phase composition, inclusions, and grain structures, which are the differentiating features of AM metals. Furthermore, we propose data-mining as an effective solution for novel rapid design and optimization, which is motivated by the numerous influencing factors in the AM process. We believe this paper will provide a roadmap to advance AM fundamental understanding and guide the monitoring and advanced diagnostics of AM processing.

  17. Do Safer Sex Self-Efficacy, Attitudes toward Condoms, and HIV Transmission Risk Beliefs Differ among Men who have Sex with Men, Heterosexual Men, and Women Living with HIV?

    Science.gov (United States)

    Widman, Laura; Golin, Carol E.; Grodensky, Catherine A.; Suchindran, Chirayath

    2013-01-01

    To understand sexual decision-making processes among people living with HIV, we compared safer sex self-efficacy, condom attitudes, sexual beliefs, and rates of unprotected anal or vaginal intercourse with at-risk partners (UAVI-AR) in the past 3 months among 476 people living with HIV: 185 men who have sex with men (MSM), 130 heterosexual men, and 161 heterosexual women. Participants were enrolled in SafeTalk, a randomized, controlled trial of a safer sex intervention. We found 15% of MSM, 9% of heterosexual men, and 12% of heterosexual women engaged in UAVI-AR. Groups did not differ in self-efficacy or sexual attitudes/beliefs. However, the associations between these variables and UAVI-AR varied within groups: greater self-efficacy predicted less UAVI-AR for MSM and women, whereas more positive condom attitudes – but not self-efficacy – predicted less UAVI-AR for heterosexual men. These results suggest HIV prevention programs should tailor materials to different subgroups. PMID:22252475

  18. Steering patients to safer hospitals? The effect of a tiered hospital network on hospital admissions.

    Science.gov (United States)

    Scanlon, Dennis P; Lindrooth, Richard C; Christianson, Jon B

    2008-10-01

    To determine if a tiered hospital benefit and safety incentive shifted the distribution of admissions toward safer hospitals. A large manufacturing company instituted the hospital safety incentive (HSI) for union employees. The HSI gave union patients a financial incentive to choose hospitals that met the Leapfrog Group's three patient safety "leaps." The analysis merges data from four sources: claims and enrollment data from the company, the American Hospital Association, the AHRQ HCUP-SID, and a state Office of the Insurance Commissioner. Changes in hospital admissions' patterns for union and nonunion employees using a difference-in-difference design. We estimate the probability of choosing a specific hospital from a set of available alternatives using conditional logistic regression. Patients affiliated with the engineers' union and admitted for a medical diagnosis were 2.92 times more likely to select a hospital designated as safer in the postperiod than in the preperiod, while salaried nonunion (SNU) patients (not subject to the financial incentive) were 0.64 times as likely to choose a compliant hospital in the post- versus preperiod. The difference-in-difference estimate, which is based on the predictions of the conditional logit model, is 0.20. However, the machinists' union was also exposed to the incentive and they were no more likely to choose a safer hospital than the SNU patients. The incentive did not have an effect on patients admitted for a surgical diagnosis, regardless of union status. All patients were averse to travel time, but those union patients selecting an incentive hospital were less averse to travel time. Patient price incentives and quality/safety information may influence hospital selection decisions, particularly for medical admissions, though the optimal incentive level for financial return to the plan sponsor is not clear.

  19. Formal concept analysis applied to the prediction of additives for galvanizing process

    Directory of Open Access Journals (Sweden)

    J. Klimeš

    2010-04-01

    Full Text Available Formal concept analysis is a new mathematical approach to data analysis, data mining and to discavering patterns in data. The result of the application of the formal concept analysis method to the behavior of the galvanizing of rimmed steel is presented. Effects of additives in the galvanizing process have been correlated to the chemical element properties of the additives. This model may also help to design new alloys as additives in the galvanizing process.

  20. Special Aviation Fire and Explosion Reduction (SAFER) Advisory Committee. Volume IIB.

    Science.gov (United States)

    1980-06-26

    alternates be identified collectively as the "SAFER Advisory Committee," or simply the Committee. 2. That the Committee serve as the decision-making body...iefta 10 e - Avisttln Kal £s1a~r*W. Odke Of W- rPs A..ecn~e "I t12, AdOWt(~ 0 W ae Itirea~t pgsPer110 I’o Mhet Cuxlser Attenton. Rulem LlozkCL is ira...factors, such as bur.t.it ot inha~ation of toxic gases. It is only in recent years that t-e :37 o actempted to collect such data. 4. Except for the KC

  1. Assessing Potential Additional PFAS Retention Processes in the Subsurface

    Science.gov (United States)

    Brusseau, M. L.

    2017-12-01

    Understanding the transport and fate of per- and poly-fluorinated alkyl substances (PFASs) in the subsurface is critical for accurate risk assessments and design of effective remedial actions. Current conceptual and mathematical models are based on an assumption that solid-phase adsorption is the sole source of retention for PFASs. However, additional retention processes may be relevant for PFAS compounds in vadose-zone systems and in source zones that contain trapped immiscible organic liquids. These include adsorption at the air-water interface, partitioning to the soil atmosphere, adsorption at the NAPL-water interface, and absorption by NAPL. A multi-process retention model is proposed to account for these potential additional sources of PFAS retardation. An initial assessment of the relative magnitudes and significance of these retention processes was conducted for three representative PFASs, perfluorooctanoic acid (PFOA), perfluorooctane sulfonate (PFOS), and 8:2 fluorotelomer alcohol (FTOH). Data collected from the literature were used to determine measured or estimated values for the relevant distribution coefficients, which were in turn used to calculate retardation factors for a representative porous medium. Adsorption at the air-water interface was shown to be a primary source of retention for PFOA and PFOS, contributing approximately 80% of total retardation. Adsorption to NAPL-water interfaces and absorption by bulk NAPL were also shown to be significant sources of retention for PFOS and PFOA. The latter process was the predominant source of retention for 8:2 FTOH, contributing 98% of total retardation. These results indicate that we may anticipate significant retention of PFASs by these additional processes. In such cases, retardation of PFASs in source areas may be significantly greater than what is typically estimated based on the standard assumption of solid-phase adsorption as the sole retention mechanism. This has significant ramifications for

  2. Cutting the cost of South African antiretroviral therapy using newer, safer drugs

    Directory of Open Access Journals (Sweden)

    W F Venter

    2017-01-01

    Full Text Available Antiretrovirals are a significant cost driver for HIV programmes. Current first-line regimens have performed well in real-life programmes, but have a low barrier to virological resistance and still carry toxicity that limits adherence. New drug developments may mean that we have access to safer, more robust and cheaper regimens, but only if the appropriate clinical trials are conducted. We briefly discuss these trials, and demonstrate the large cost savings to the South African HIV programme if these are successful.

  3. Cold Spraying of Armstrong Process Titanium Powder for Additive Manufacturing

    Science.gov (United States)

    MacDonald, D.; Fernández, R.; Delloro, F.; Jodoin, B.

    2017-04-01

    Titanium parts are ideally suited for aerospace applications due to their unique combination of high specific strength and excellent corrosion resistance. However, titanium as bulk material is expensive and challenging/costly to machine. Production of complex titanium parts through additive manufacturing looks promising, but there are still many barriers to overcome before reaching mainstream commercialization. The cold gas dynamic spraying process offers the potential for additive manufacturing of large titanium parts due to its reduced reactive environment, its simplicity to operate, and the high deposition rates it offers. A few challenges are to be addressed before the additive manufacturing potential of titanium by cold gas dynamic spraying can be reached. In particular, it is known that titanium is easy to deposit by cold gas dynamic spraying, but the deposits produced are usually porous when nitrogen is used as the carrier gas. In this work, a method to manufacture low-porosity titanium components at high deposition efficiencies is revealed. The components are produced by combining low-pressure cold spray using nitrogen as the carrier gas with low-cost titanium powder produced using the Armstrong process. The microstructure and mechanical properties of additive manufactured titanium components are investigated.

  4. Motives and barriers to safer sex and regular STI testing among MSM soon after HIV diagnosis

    NARCIS (Netherlands)

    Heijman, Titia; Zuure, Freke; Stolte, Ineke; Davidovich, Udi

    2017-01-01

    Understanding why some recently with HIV diagnosed men who have sex with men (MSM) choose for safer sex and regular STI testing, whereas others do not, is important for the development of interventions that aim to improve the sexual health of those newly infected. To gain insight into motives and

  5. Are nuclear ships environmentally safer than conventionally powered ships

    International Nuclear Information System (INIS)

    Bone, C.A.; Molgaard, C.A.; Helmkamp, J.C.; Golbeck, A.L.

    1988-01-01

    An epidemiologic analysis was conducted to determine if risk of hospitalization varied by age, ship type, or occupation between nuclear and conventional powered ship crews in the U.S. Navy. Study cohorts consisted of all male enlisted personnel who served exclusively aboard conventional or nuclear powered aircraft carriers and cruisers during the years 1975-1979; cases were those men hospitalized during this period (N = 48,242). Conventional ship personnel showed significantly elevated rates of injury and disease when compared to nuclear ship personnel. The largest relative risks by age occurred for conventional ship crewmen less than 30 years old. Seaman, logistics (supply), and healthcare personnel serving aboard conventional ships comprised the occupational groups exhibiting the highest hospitalization rate differentials. The results strongly suggest that nuclear ships provide a healthier, safer working and living environment than conventional ships

  6. Gender power control, sexual experiences, safer sex practices, and potential HIV risk behaviors among young Asian-American women.

    Science.gov (United States)

    Hahm, Hyeouk Chris; Lee, Jieha; Rough, Kathryn; Strathdee, Steffanie A

    2012-01-01

    We examined the prevalence of three domains of sexual behaviors among young Asian-American women: sexual experiences, safer sex practices, and potential HIV risk behaviors. We also investigated the impact of gender power control on these domains. Among sexually experienced women, 51% reported using condoms during their most recent sex act, 63% reported inconsistent condom use, and 18% reported ever having forced sex. Multiple logistic regression analyses revealed that women's perceived lower relationship power control was not associated with vaginal sex or safer sex practices, but it was powerfully associated with forced sex and all three potential HIV risk behaviors. This study demonstrates that control within young Asian-American women's intimate relationships exerts different associations depending on the type of sexual behavior. The application of the Theory of Gender and Power should be employed with prudence when designing HIV interventions for this population.

  7. Fertility Intentions, Pregnancy, and Use of PrEP and ART for Safer Conception Among East African HIV Serodiscordant Couples.

    Science.gov (United States)

    Heffron, Renee; Thomson, Kerry; Celum, Connie; Haberer, Jessica; Ngure, Kenneth; Mugo, Nelly; Bukusi, Elizabeth; Katabira, Elly; Odoyo, Josephine; Bulya, Nulu; Asiimwe, Stephen; Tindimwebwa, Edna; Baeten, Jared M

    2017-09-11

    African HIV serodiscordant couples often desire pregnancy, despite sexual HIV transmission risk during pregnancy attempts. Pre-exposure prophylaxis (PrEP) and antiretroviral therapy (ART) reduce HIV risk and can be leveraged for safer conception but how well these strategies are used for safer conception is not known. We conducted an open-label demonstration project of the integrated delivery of PrEP and ART among 1013 HIV serodiscordant couples from Kenya and Uganda followed quarterly for 2 years. We evaluated fertility intentions, pregnancy incidence, the use of PrEP and ART during peri-conception, and peri-conception HIV incidence. At enrollment, 80% of couples indicated a desire for more children. Pregnancy incidence rates were 18.5 and 18.7 per 100 person years among HIV-uninfected and HIV-infected women, and higher among women who recently reported fertility intention (adjusted odds ratio 3.43, 95% CI 2.38-4.93) in multivariable GEE models. During the 6 months preceding pregnancy, 82.9% of couples used PrEP or ART and there were no HIV seroconversions. In this cohort with high pregnancy rates, integrated PrEP and ART was readily used by HIV serodiscordant couples, including during peri-conception periods. Widespread scale-up of safer conception counseling and services is warranted to respond to strong desires for pregnancy among HIV-affected men and women.

  8. Validation of the FEA of a deep drawing process with additional force transmission

    Science.gov (United States)

    Behrens, B.-A.; Bouguecha, A.; Bonk, C.; Grbic, N.; Vucetic, M.

    2017-10-01

    In order to meet requirements by automotive industry like decreasing the CO2 emissions, which reflects in reducing vehicles mass in the car body, the chassis and the powertrain, the continuous innovation and further development of existing production processes are required. In sheet metal forming processes the process limits and components characteristics are defined through the process specific loads. While exceeding the load limits, a failure in the material occurs, which can be avoided by additional force transmission activated in the deep drawing process before the process limit is achieved. This contribution deals with experimental investigations of a forming process with additional force transmission regarding the extension of the process limits. Based on FEA a tool system is designed and developed by IFUM. For this purpose, the steel material HCT600 is analyzed numerically. Within the experimental investigations, the deep drawing processes, with and without the additional force transmission are carried out. Here, a comparison of the produced rectangle cups is done. Subsequently, the identical deep drawing processes are investigated numerically. Thereby, the values of the punch reaction force and displacement are estimated and compared with experimental results. Thus, the validation of material model is successfully carried out on process scale. For further quantitative verification of the FEA results the experimental determined geometry of the rectangular cup is measured optically with ATOS system of the company GOM mbH and digitally compared with external software Geomagic®QualifyTM. The goal of this paper is the verification of the transferability of the FEA model for a conventional deep drawing process to a deep drawing process with additional force transmission with a counter punch.

  9. Multi-level Correlates of Safer Conception Methods Awareness and Attitudes Among Ugandan HIV Clients with Fertility Intentions.

    Science.gov (United States)

    Wagner, Glenn J; Woldetsadik, Mahlet A; Beyeza-Kashesya, Jolly; Goggin, Kathy; Mindry, Deborah; Finocchario-Kessler, Sarah; Khanakwa, Sarah; Wanyenze, Rhoda K

    2016-03-01

    Many people living with HIV desire childbearing, but low cost safer conception methods (SCM) such as timed unprotected intercourse (TUI) and manual self-insemination (MSI) are rarely used. We examined awareness and attitudes towards SCM, and the correlates of these constructs among 400 HIV clients with fertility intentions in Uganda. Measures included awareness, self-efficacy, and motivation regarding SCM, as well as demographics, health management, partner and provider characteristics. Just over half knew that MSI (53%) and TUI (51%) reduced transmission risk during conception, and 15% knew of sperm washing and pre-exposure prophylaxis. In separate regression models for SCM awareness, motivation, and self-efficacy, nearly all independent correlates were related to the partner, including perceived willingness to use SCM, knowledge of respondent's HIV status, HIV-seropositivity, marriage and equality in decision making within the relationship. These findings suggest the importance of partners in promoting SCM use and partner inclusion in safer conception counselling.

  10. Additives in UV and ionising radiation grafting and curing processes

    International Nuclear Information System (INIS)

    Garnett, J.L.; Ng, L.T.; Viengkhou, V.

    1998-01-01

    Full text: Curing of polymers induced by both UV and ionising radiation are now established technologies. Currently both systems are predominantly based on acrylate chemistry. UV processes use photoinitiators to achieve fast polymerisation. In the proposed paper the significance of the occurrence of concurrent grafting with cure will be examined. particularly with respect to the recycling of finished product. Basic studies on grafting initiated by UV and ionising radiation will be discussed. Polar methyl methacrylate (MMA) and non-polar styrene will be used as representative monomers with cellulose and propylene typifying the backbone polymers. The additives chosen for examination in this study are predominantly components used in radiation curing formulations since grafting and curing are known to be mechanically related. The additives used were mineral acid, photoinitiators, vinyl ethers, oligomers, polyfunctional monomers including multifunctional acrylates (MFAs) and methacrylates (MFMAs). For the first time the use of charge transfer complexes in the Mulliken sense as additives in radiation grafting will be discussed. The CT complexes themselves, being monomers, have also been grafted to the above polymers. Recent developments with excimer laser sources for initiating these processes will be discussed, especially the use of non-acrylate chemistry. Excimer laser sources are shown to complement conventional UV and ionising radiation and are photoinitiator free. Mechanisms for the above grafting and curing processes will be outlined

  11. Quality and efficiency successes leveraging IT and new processes.

    Science.gov (United States)

    Chaiken, Barry P; Christian, Charles E; Johnson, Liz

    2007-01-01

    Today, healthcare annually invests billions of dollars in information technology, including clinical systems, electronic medical records and interoperability platforms. While continued investment and parallel development of standards are critical to secure exponential benefits from clinical information technology, intelligent and creative redesign of processes through path innovation is necessary to deliver meaningful value. Reports from two organizations included in this report review the steps taken to reinvent clinical processes that best leverage information technology to deliver safer and more efficient care. Good Samaritan Hospital, Vincennes, Indiana, implemented electronic charting, point-of-care bar coding of medications prior to administration, and integrated clinical documentation for nursing, laboratory, radiology and pharmacy. Tenet Healthcare, during its implementation and deployment of multiple clinical systems across several hospitals, focused on planning that included team-based process redesign. In addition, Tenet constructed valuable and measurable metrics that link outcomes with its strategic goals.

  12. Designing out Crime - Voices from the Fields: Editorial for Special Edition of Safer Communities

    OpenAIRE

    Monchuk, Leanne; Clancey, Garner

    2013-01-01

    ‘Crime prevention through environmental design (CPTED)’, ‘designing out crime’, ‘safer by design’, ‘secured by design’ or any of the other ‘flavours’ of manipulating the built environment to prevent crime, invariably engender an inter-disciplinary approach. This work is frequently the domain of architects, urban planners, police, security professionals, local authority planners and community safety professionals (amongst others). Despite the real work being undertaken by these actors, the div...

  13. On Demand Internal Short Circuit Device Enables Verification of Safer, Higher Performing Battery Designs

    Energy Technology Data Exchange (ETDEWEB)

    Darcy, Eric; Keyser, Matthew

    2017-05-15

    The Internal Short Circuit (ISC) device enables critical battery safety verification. With the aluminum interstitial heat sink between the cells, normal trigger cells cannot be driven into thermal runaway without excessive temperature bias of adjacent cells. With an implantable, on-demand ISC device, thermal runaway tests show that the conductive heat sinks protected adjacent cells from propagation. High heat dissipation and structural support of Al heat sinks show high promise for safer, higher performing batteries.

  14. Addition of calcium compounds to reduce soluble oxalate in a high oxalate food system.

    Science.gov (United States)

    Bong, Wen-Chun; Vanhanen, Leo P; Savage, Geoffrey P

    2017-04-15

    Spinach (Spinacia oleracea L.) is often used as a base vegetable to make green juices that are promoted as healthy dietary alternatives. Spinach is known to contain significant amounts of oxalates, which are toxic and, if consumed regularly, can lead to the development of kidney stones. This research investigates adding 50-500mg increments of calcium carbonate, calcium chloride, calcium citrate and calcium sulphate to 100g of raw homogenates of spinach to determine whether calcium would combine with the soluble oxalate present in the spinach. Calcium chloride was the most effective additive while calcium carbonate was the least effective. The formation of insoluble oxalate after incubation at 25°C for 30min is a simple practical step that can be incorporated into the juicing process. This would make the juice considerably safer to consume on a regular basis. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Three-dimensional multislice spiral computed tomographic angiography: a potentially useful tool for safer free tissue transfer to complicated regions

    DEFF Research Database (Denmark)

    Demirtas, Yener; Cifci, Mehmet; Kelahmetoglu, Osman

    2009-01-01

    Three-dimensional multislice spiral computed tomographic angiography (3D-MSCTA) is a minimally invasive method of vascular mapping. The aim of this study was to evaluate the clinical usefulness of this imaging technique in delineating the recipient vessels for safer free tissue transfer to compli......Three-dimensional multislice spiral computed tomographic angiography (3D-MSCTA) is a minimally invasive method of vascular mapping. The aim of this study was to evaluate the clinical usefulness of this imaging technique in delineating the recipient vessels for safer free tissue transfer...... be kept in mind, especially inthe patients with peripheral vascular disease. 3D-MSCTA has the potential to replace digital subtraction angiography for planning of microvascular reconstructions and newer devices with higher resolutions will probably increase the reliability of this technique. (c) 2009...

  16. Contribution of food additives to sodium and phosphorus content of diets rich in processed foods.

    Science.gov (United States)

    Carrigan, Anna; Klinger, Andrew; Choquette, Suzanne S; Luzuriaga-McPherson, Alexandra; Bell, Emmy K; Darnell, Betty; Gutiérrez, Orlando M

    2014-01-01

    Phosphorus-based food additives increase the total phosphorus content of processed foods. However, the extent to which these additives augment total phosphorus intake per day is unclear. To examine the contribution of phosphorus-based food additives to the total phosphorus content of processed foods, separate 4-day menus for a low-additive and additive-enhanced diet were developed using Nutrition Data System for Research (NDSR) software. The low-additive diet was designed to conform to U.S. Department of Agriculture guidelines for energy and phosphorus intake (∼2,000 kcal/day and 900 mg of phosphorus per day), and it contained minimally processed foods. The additive-enhanced diet contained the same food items as the low-additive diet except that highly processed foods were substituted for minimally processed foods. Food items from both diets were collected, blended, and sent for measurement of energy and nutrient intake. The low-additive and additive-enhanced diet provided approximately 2,200 kcal, 700 mg of calcium, and 3,000 mg of potassium per day on average. Measured sodium and phosphorus content standardized per 100 mg of food was higher each day of the additive-enhanced diet as compared with the low-additive diet. When averaged over the 4 menu days, the measured phosphorus and sodium contents of the additive-enhanced diet were 606 ± 125 and 1,329 ± 642 mg higher than the low-additive diet, respectively, representing a 60% increase in total phosphorus and sodium content on average. When comparing the measured values of the additive-enhanced diet to NDSR-estimated values, there were no statistically significant differences in measured versus estimated phosphorus contents. Phosphorus and sodium additives in processed foods can substantially augment phosphorus and sodium intake, even in relatively healthy diets. Current dietary software may provide reasonable estimates of the phosphorus content in processed foods. Copyright © 2014 National Kidney

  17. Gender Power Control, Sexual Experiences, Safer Sex Practices, and Potential HIV Risk Behaviors Among Young Asian-American Women

    Science.gov (United States)

    Lee, Jieha; Rough, Kathryn; Strathdee, Steffanie A.

    2012-01-01

    We examined the prevalence of three domains of sexual behaviors among young Asian-American women: sexual experiences, safer sex practices, and potential HIV risk behaviors. We also investigated the impact of gender power control on these domains. Among sexually experienced women, 51% reported using condoms during their most recent sex act, 63% reported inconsistent condom use, and 18% reported ever having forced sex. Multiple logistic regression analyses revealed that women’s perceived lower relationship power control was not associated with vaginal sex or safer sex practices, but it was powerfully associated with forced sex and all three potential HIV risk behaviors. This study demonstrates that control within young Asian-American women’s intimate relationships exerts different associations depending on the type of sexual behavior. The application of the Theory of Gender and Power should be employed with prudence when designing HIV interventions for this population. PMID:21259042

  18. Economic trade-offs of additive manufacturing integration in injection moulding process chain

    DEFF Research Database (Denmark)

    Charalambis, Alessandro; Kerbache, Laoucine; Tosello, Guido

    2017-01-01

    Additive Manufacturing has emerged as an innovative set of novel technologies capable of replacing established manufacturing processes due to fabrication of highly complex parts and its continuous improvements of efficiency and cost effectiveness. This study is based on the idea that through...... the creation of synergies between additive and conventional manufacturing technologies it is possible to achieve greater cost advantages and operational benefits than by substituting injection moulding with additive manufacturing. The analysis presented explores the cost advantages that can be secured when...... additive manufacturing is used to support the fabrication of mould inserts for the product development phase of the injection moulding process chain. This study shows that fabrication of soft tooling by mean of AM is economically convenient with a cost reduction between 80% and 90%. Break-even points...

  19. Dry process potentials

    International Nuclear Information System (INIS)

    Faugeras, P.

    1997-01-01

    Various dry processes have been studied and more or less developed in order particularly to reduce the waste quantities but none of them had replaced the PUREX process, for reasons departing to policy errors, un-appropriate demonstration examples or too late development, although realistic and efficient dry processes such as a fluoride selective volatility based processes have been demonstrated in France (CLOVIS, ATILA) and would be ten times cheaper than the PUREX process. Dry processes could regain interest in case of a nuclear revival (following global warming fears) or thermal wastes over-production. In the near future, dry processes could be introduced in complement to the PUREX process, especially at the end of the process cycle, for a more efficient recycling and safer storage (inactivation)

  20. Hopper design for metallic powders used in additive manufacturing processes

    CSIR Research Space (South Africa)

    Visagie, N

    2013-10-01

    Full Text Available The influence of hopper geometry on the flow behaviour of typical metallic powders used in additive manufacturing processes is investigated. Bulk hopper theory provides a method of determining critical hopper parameters for bulk amounts...

  1. Oxidation processes on conducting carbon additives for lithium-ion batteries

    KAUST Repository

    La Mantia, Fabio; Huggins, Robert A.; Cui, Yi

    2012-01-01

    The oxidation processes at the interface between different types of typical carbon additives for lithium-ion batteries and carbonates electrolyte above 5 V versus Li/Li+ were investigated. Depending on the nature and surface area of the carbon

  2. Piroxicam-β-cyclodextrin: a GI safer piroxicam.

    Science.gov (United States)

    Scarpignato, C

    2013-01-01

    more rapid onset of action after oral administration and improved GI tolerability because of minimization of the drug gastric effects. One such drug, piroxicam-β-cyclodextrin (PBC), has been used in Europe for 25 years. Preclinical and clinical pharmacology of PBC do show that the β-cyclodextrin inclusion complex of piroxicam is better tolerated from the upper GI tract than free piroxicam, while retaining all the analgesic and anti-inflammatory properties of the parent compound. In addition, the drug is endowed with a quick absorption rate, which translates into a faster onset of analgesic activity, an effect confirmed in several clinical studies. An analysis of the available trials show that PBC has a GI safety profile, which is better than that displayed by uncomplexed piroxicam. Being an inclusion complex of piroxicam, whose CV safety has been pointed out by several observational studies, PBC should be viewed as a CV safe anti-inflmmatory compound and a GI safer alternative to piroxicam. As a consequence, it should be considered as a useful addition to our therapeutic armamentarium.

  3. Heavy Sexual Content Versus Safer Sex Content: A Content Analysis of the Entertainment Education Drama Shuga.

    Science.gov (United States)

    Booker, Nancy Achieng'; Miller, Ann Neville; Ngure, Peter

    2016-12-01

    Extremely popular with Kenyan youth, the entertainment-education drama Shuga was designed with specific goals of promoting condom use, single versus multiple sexual partners, and destigmatization of HIV. Almost as soon as it aired, however, it generated controversy due to its extensive sexual themes and relatively explicit portrayal of sexual issues. To determine how safer sex, antistigma messages, and overall sexual content were integrated into Shuga, we conducted a content analysis. Results indicated that condom use and HIV destigmatization messages were frequently and clearly communicated. Negative consequences for risky sexual behavior were communicated over the course of the entire series. Messages about multiple concurrent partnerships were not evident. In addition, in terms of scenes per hour of programming, Shuga had 10.3 times the amount of sexual content overall, 8.2 times the amount of sexual talk, 17.8 times the amount of sexual behavior, and 9.4 times the amount of sexual intercourse as found in previous analysis of U.S. entertainment programming. Research is needed to determine how these factors may interact to influence adolescent viewers of entertainment education dramas.

  4. Additive Manufacturing Processes: Selective Laser Melting, Electron Beam Melting and Binder Jetting-Selection Guidelines.

    Science.gov (United States)

    Gokuldoss, Prashanth Konda; Kolla, Sri; Eckert, Jürgen

    2017-06-19

    Additive manufacturing (AM), also known as 3D printing or rapid prototyping, is gaining increasing attention due to its ability to produce parts with added functionality and increased complexities in geometrical design, on top of the fact that it is theoretically possible to produce any shape without limitations. However, most of the research on additive manufacturing techniques are focused on the development of materials/process parameters/products design with different additive manufacturing processes such as selective laser melting, electron beam melting, or binder jetting. However, we do not have any guidelines that discuss the selection of the most suitable additive manufacturing process, depending on the material to be processed, the complexity of the parts to be produced, or the design considerations. Considering the very fact that no reports deal with this process selection, the present manuscript aims to discuss the different selection criteria that are to be considered, in order to select the best AM process (binder jetting/selective laser melting/electron beam melting) for fabricating a specific component with a defined set of material properties.

  5. Additive Manufacturing Processes: Selective Laser Melting, Electron Beam Melting and Binder Jetting—Selection Guidelines

    Science.gov (United States)

    Konda Gokuldoss, Prashanth; Kolla, Sri; Eckert, Jürgen

    2017-01-01

    Additive manufacturing (AM), also known as 3D printing or rapid prototyping, is gaining increasing attention due to its ability to produce parts with added functionality and increased complexities in geometrical design, on top of the fact that it is theoretically possible to produce any shape without limitations. However, most of the research on additive manufacturing techniques are focused on the development of materials/process parameters/products design with different additive manufacturing processes such as selective laser melting, electron beam melting, or binder jetting. However, we do not have any guidelines that discuss the selection of the most suitable additive manufacturing process, depending on the material to be processed, the complexity of the parts to be produced, or the design considerations. Considering the very fact that no reports deal with this process selection, the present manuscript aims to discuss the different selection criteria that are to be considered, in order to select the best AM process (binder jetting/selective laser melting/electron beam melting) for fabricating a specific component with a defined set of material properties. PMID:28773031

  6. Characterization of additive manufacturing processes for polymer micro parts productions using direct light processing (DLP) method

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

    The process capability of additive manufacturing (AM) for direct production of miniaturized polymer components with micro features is analyzed in this work. The consideration of the minimum printable feature size and obtainable tolerances of AM process is a critical step to establish a process...... chains for the production of parts with micro scale features. A specifically designed direct light processing (DLP) AM machine suitable for precision printing has been used. A test part is designed having features with different sizes and aspect ratios in order to evaluate the DLP AM machine capability...

  7. Does the real-time ultrasound guidance provide safer venipuncture in implantable venous port implantation?

    Science.gov (United States)

    Yıldırım, İlknur; Tütüncü, Ayşe Çiğdem; Bademler, Süleyman; Özgür, İlker; Demiray, Mukaddes; Karanlık, Hasan

    2018-03-01

    To examine whether the real-time ultrasound-guided venipuncture for implantable venous port placement is safer than the traditional venipuncture. The study analyzed the results of 2153 venous ports placed consecutively from January 2009 to January 2016. A total of 922 patients in group 1 and 1231 patients in group 2 were admitted with venous port placed using the traditional landmark subclavian approach and real-time ultrasound-guided axillary approach, respectively. Sociodemographic characteristics of patients, early (pneumothorax, pinch-off syndrome, arterial puncture, hematoma, and malposition arrhythmia) and late (deep vein thrombosis, obstruction, infection, erosion-dehiscence, and rotation of the port chamber) complications and the association of these complications with the implantation method were evaluated. There were no significant differences in the sociodemographic characteristics of the patients between the two groups. The overall and early complications in group 2 were significantly lower than those in group 1. Pinch-off syndrome only developed in group 1. Seven patients and two patients had pneumothorax in groups 1 and 2, respectively. Puncture number was significantly associated with the development of the overall complications. The ultrasound-guided axillary approach may be preferred as a method to reduce the risk of both early and late complications. Large, randomized, controlled prospective trials will be helpful in determining a safer implantable venous port implantation technique.

  8. Oxidation processes on conducting carbon additives for lithium-ion batteries

    KAUST Repository

    La Mantia, Fabio

    2012-11-21

    The oxidation processes at the interface between different types of typical carbon additives for lithium-ion batteries and carbonates electrolyte above 5 V versus Li/Li+ were investigated. Depending on the nature and surface area of the carbon additive, the irreversible capacity during galvanostatic cycling between 2.75 and 5.25 V versus Li/Li+ could be as high as 700 mAh g-1 (of carbon). In the potential region below 5 V versus Li/Li+, high surface carbon additives also showed irreversible plateaus at about 4.1-4.2 and 4.6 V versus Li/Li+. These plateaus disappeared after thermal treatments at or above 150 °C in inert gas. The influence of the irreversible capacity of carbon additives on the overall performances of positive electrodes was discussed. © 2012 Springer Science+Business Media Dordrecht.

  9. A framework for safer driving in Mauritius

    Directory of Open Access Journals (Sweden)

    V. Bassoo

    2017-12-01

    Full Text Available According to the National Transport Authority (NTA, there were 493,081 registered vehicles in Mauritius in April 2016, which represents a 1.4% annual increase compared to 2015. Despite the sensitization campaigns and the series of measures setup by the Minister of Public Infrastructure and Land Transport, the number of road accidents continues to rise. The three main elements that contribute to accidents are: road infrastructure, vehicle and driver. The driver has the highest contribution in collisions. If the driver is given the right information (e.g. driving behaviour, accident-prone areas and vehicle status at the right time, he/she can make better driving decisions and react promptly to critical situations. This paper proposes a framework for safer driving in Mauritius that uses an on-board car diagnostic module (OBDII to collect data such as vehicle average speed, engine revolution and acceleration. This module relays the data to a cloud environment where an adaptive algorithm analyses the data and predicts driver behaviour in real-time. Based on driving behaviour, mobile alerts can be sent to the driver in the form of messages, voice commands or beeps. A survey was also carried out to evaluate the acceptance rate of such a framework by people of different age groups in Mauritius.

  10. 'He lacks his fatherhood': safer conception technologies and the biological imperative for fatherhood among recently-diagnosed Xhosa-speaking men living with HIV in South Africa.

    Science.gov (United States)

    Taylor, Tonya N; Mantell, Joanne E; Nywagi, Ntobeko; Cishe, Nomazizi; Cooper, Diane

    2013-01-01

    This paper explores notions of fatherhood and their linkages to fertility desires and intentions among a treatment-naïve cohort of Xhosa-speaking male key informants living with HIV, aged 20-53 in Cape Town, South Africa. Analysis is based on an initial 27, and 20 follow-up, interviews with men who were part of a study that assessed the acceptability of safer conception and alternative parenting strategies among men and women newly diagnosed with HIV to inform an intervention. Grounded theory analysis revealed themes related to the cultural imperative of biologically-connected fatherhood. Certain safer-conception strategies aimed at minimising the risk of HIV transmission were perceived as threats to paternity. These findings suggest that understanding of social and cultural beliefs related to notions of paternity and fatherhood may inform the implementation of acceptable safer-conception options for HIV-positive men and their infected and uninfected female partners in a high-HIV prevalence, low-resource setting.

  11. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 356: Mud Pits and Disposal Sites, Nevada Test Site, Nevada (Revision No. 0, August 2001); FINAL

    International Nuclear Information System (INIS)

    2001-01-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions necessary for the characterization and closure of Corrective Action Unit (CAU) 356, Mud Pits and Disposal Sites, as identified in the Federal Facility Agreement and Consent Order (FFACO). The CAU, located on the Nevada Test Site in Nevada, consists of seven Corrective Action Sites (CASs): CAS 03-04-01, Area 3 Change House Septic System; CAS 03-09-01, Mud Pit Spill Over; CAS 03-09-03, Mud Pit; CAS 03-09-04, Mud Pit; CAS 03-09-05, Mud Pit; CAS 20-16-01, Landfill; CAS 20-22-21, Drums. Sufficient information and process knowledge from historical documentation and investigations are the basis for the development of the phased approach chosen to address the data collection activities prior to implementing the preferred closure alternative for each CAS. The Phase I investigation will determine through collection of environmental samples from targeted populations (i.e., mud/soil cuttings above textural discontinuity) if contaminants of potential concern (COPCs) are present in concentrations exceeding preliminary action levels (PALs) at each of the CASs. If COPCs are present above PALs, a Phase II investigation will be implemented to determine the extent of contamination to support the appropriate corrective action alternative to complete closure of the site. Groundwater impacts from potentially migrating contaminants are not expected due to the depths to groundwater and limiting hydrologic drivers of low precipitation and high evaporation rates. Future land-use scenarios limit future uses to industrial activities; therefore, future residential uses are not considered. Potential exposure routes to site workers from contaminants of concern in septage and soils include oral ingestion, inhalation, or dermal contact (absorption) through in-advertent disturbance of contaminated structures and/or soils. Diesel within drilling muds is expected to be the primary COPC based on process

  12. Numerical simulation of residual stress in laser based additive manufacturing process

    Science.gov (United States)

    Kalyan Panda, Bibhu; Sahoo, Seshadev

    2018-03-01

    Minimizing the residual stress build-up in metal-based additive manufacturing plays a pivotal role in selecting a particular material and technique for making an industrial part. In beam-based additive manufacturing, although a great deal of effort has been made to minimize the residual stresses, it is still elusive how to do so by simply optimizing the processing parameters, such as beam size, beam power, and scan speed. Amid different types of additive manufacturing processes, Direct Metal Laser Sintering (DMLS) process uses a high-power laser to melt and sinter layers of metal powder. The rapid solidification and heat transfer on powder bed endows a high cooling rate which leads to the build-up of residual stresses, that will affect the mechanical properties of the build parts. In the present work, the authors develop a numerical thermo-mechanical model for the measurement of residual stress in the AlSi10Mg build samples by using finite element method. Transient temperature distribution in the powder bed was assessed using the coupled thermal to structural model. Subsequently, the residual stresses were estimated with varying laser power. From the simulation result, it found that the melt pool dimensions increase with increasing the laser power and the magnitude of residual stresses in the built part increases.

  13. Streamlined Approach for Environmental Restoration (SAFER) Plan for Corrective Action Unit 544: Cellars, Mud Pits, and Oil Spills, Nevada Test Site, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Mark Krauss

    2010-07-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan addresses the actions needed to achieve closure for Corrective Action Unit (CAU) 544, Cellars, Mud Pits, and Oil Spills, identified in the Federal Facility Agreement and Consent Order (FFACO). Corrective Action Unit 544 comprises the following 20 corrective action sites (CASs) located in Areas 2, 7, 9, 10, 12, 19, and 20 of the Nevada Test Site (NTS): • 02-37-08, Cellar & Mud Pit • 02-37-09, Cellar & Mud Pit • 07-09-01, Mud Pit • 09-09-46, U-9itsx20 PS #1A Mud Pit • 10-09-01, Mud Pit • 12-09-03, Mud Pit • 19-09-01, Mud Pits (2) • 19-09-03, Mud Pit • 19-09-04, Mud Pit • 19-25-01, Oil Spill • 19-99-06, Waste Spill • 20-09-01, Mud Pits (2) • 20-09-02, Mud Pit • 20-09-03, Mud Pit • 20-09-04, Mud Pits (2) • 20-09-06, Mud Pit • 20-09-07, Mud Pit • 20-09-10, Mud Pit • 20-25-04, Oil Spills • 20-25-05, Oil Spills This plan provides the methodology for field activities needed to gather the necessary information for closing each CAS. There is sufficient information and process knowledge from historical documentation and investigations of similar sites regarding the expected nature and extent of potential contaminants to recommend closure of CAU 544 using the SAFER process. Using the approach approved for previous mud pit investigations (CAUs 530–535), 14 mud pits have been identified that • are either a single mud pit or a system of mud pits, • are not located in a radiologically posted area, and • have no evident biasing factors based on visual inspections. These 14 mud pits are recommended for no further action (NFA), and further field investigations will not be conducted. For the sites that do not meet the previously approved closure criteria, additional information will be obtained by conducting a field investigation before selecting the appropriate corrective action for each CAS. The results of the field investigation will support a defensible

  14. SWOT analysis for safer carriage of bulk liquid chemicals in tankers.

    Science.gov (United States)

    Arslan, Ozcan; Er, Ismail Deha

    2008-06-15

    The application of strengths, weaknesses, opportunities and threats (SWOT) analysis to formulation of strategy concerned with the safe carriage of bulk liquid chemicals in maritime tankers was examined in this study. A qualitative investigation using SWOT analysis has been implemented successfully for ships that are designed to carry liquid chemicals in bulk. The originality of this study lies in the use of SWOT analysis as a management tool to formulate strategic action plans for ship management companies, ship masters and officers for the carriage of dangerous goods in bulk. With this transportation-based SWOT analysis, efforts were made to explore the ways and means of converting possible threats into opportunities, and changing weaknesses into strengths; and strategic plans of action were developed for safer tanker operation.

  15. Development of a theory-guided pan-European computer-assisted safer sex intervention.

    Science.gov (United States)

    Nöstlinger, Christiana; Borms, Ruth; Dec-Pietrowska, Joanna; Dias, Sonia; Rojas, Daniela; Platteau, Tom; Vanden Berghe, Wim; Kok, Gerjo

    2016-12-01

    HIV is a growing public health problem in Europe, with men-having-sex-with-men and migrants from endemic regions as the most affected key populations. More evidence on effective behavioral interventions to reduce sexual risk is needed. This article describes the systematic development of a theory-guided computer-assisted safer sex intervention, aiming at supporting people living with HIV in sexual risk reduction. We applied the Intervention Mapping (IM) protocol to develop this counseling intervention in the framework of a European multicenter study. We conducted a needs assessment guided by the information-motivation-behavioral (IMB) skills model, formulated change objectives and selected theory-based methods and practical strategies, i.e. interactive computer-assisted modules as supporting tools for provider-delivered counseling. Theoretical foundations were the IMB skills model, social cognitive theory and the transtheoretical model, complemented by dual process models of affective decision making to account for the specifics of sexual behavior. The counseling approach for delivering three individual sessions was tailored to participants' needs and contexts, adopting elements of motivational interviewing and cognitive-behavioral therapy. We implemented and evaluated the intervention using a randomized controlled trial combined with a process evaluation. IM provided a useful framework for developing a coherent intervention for heterogeneous target groups, which was feasible and effective across the culturally diverse settings. This article responds to the need for transparent descriptions of the development and content of evidence-based behavior change interventions as potential pillars of effective combination prevention strategies. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  16. A Randomised Controlled Trial Using Mobile Advertising to Promote Safer Sex and Sun Safety to Young People

    Science.gov (United States)

    Gold, J.; Aitken, C. K.; Dixon, H. G.; Lim, M. S. C.; Gouillou, M.; Spelman, T.; Wakefield, M.; Hellard, M. E.

    2011-01-01

    Mobile phone text messages (SMS) are a promising method of health promotion, but a simple and low cost way to obtain phone numbers is required to reach a wide population. We conducted a randomised controlled trial with simultaneous brief interventions to (i) evaluate effectiveness of messages related to safer sex and sun safety and (ii) pilot the…

  17. Sequential neural processes in abacus mental addition: an EEG and FMRI case study.

    Science.gov (United States)

    Ku, Yixuan; Hong, Bo; Zhou, Wenjing; Bodner, Mark; Zhou, Yong-Di

    2012-01-01

    Abacus experts are able to mentally calculate multi-digit numbers rapidly. Some behavioral and neuroimaging studies have suggested a visuospatial and visuomotor strategy during abacus mental calculation. However, no study up to now has attempted to dissociate temporally the visuospatial neural process from the visuomotor neural process during abacus mental calculation. In the present study, an abacus expert performed the mental addition tasks (8-digit and 4-digit addends presented in visual or auditory modes) swiftly and accurately. The 100% correct rates in this expert's task performance were significantly higher than those of ordinary subjects performing 1-digit and 2-digit addition tasks. ERPs, EEG source localizations, and fMRI results taken together suggested visuospatial and visuomotor processes were sequentially arranged during the abacus mental addition with visual addends and could be dissociated from each other temporally. The visuospatial transformation of the numbers, in which the superior parietal lobule was most likely involved, might occur first (around 380 ms) after the onset of the stimuli. The visuomotor processing, in which the superior/middle frontal gyri were most likely involved, might occur later (around 440 ms). Meanwhile, fMRI results suggested that neural networks involved in the abacus mental addition with auditory stimuli were similar to those in the visual abacus mental addition. The most prominently activated brain areas in both conditions included the bilateral superior parietal lobules (BA 7) and bilateral middle frontal gyri (BA 6). These results suggest a supra-modal brain network in abacus mental addition, which may develop from normal mental calculation networks.

  18. Process monitoring of additive manufacturing by using optical tomography

    Energy Technology Data Exchange (ETDEWEB)

    Zenzinger, Guenter, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Bamberg, Joachim, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Ladewig, Alexander, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Hess, Thomas, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Henkel, Benjamin, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de; Satzger, Wilhelm, E-mail: guenter.zenzinger@mtu.de, E-mail: alexander.ladewig@mtu.de [MTU Aero Engines AG, Dachauerstrasse 665, 80995 Munich (Germany)

    2015-03-31

    Parts fabricated by means of additive manufacturing are usually of complex shape and owing to the fabrication procedure by using selective laser melting (SLM), potential defects and inaccuracies are often very small in lateral size. Therefore, an adequate quality inspection of such parts is rather challenging, while non-destructive-techniques (NDT) are difficult to realize, but considerable efforts are necessary in order to ensure the quality of SLM-parts especially used for aerospace components. Thus, MTU Aero Engines is currently focusing on the development of an Online Process Control system which monitors and documents the complete welding process during the SLM fabrication procedure. A high-resolution camera system is used to obtain images, from which tomographic data for a 3dim analysis of SLM-parts are processed. From the analysis, structural irregularities and structural disorder resulting from any possible erroneous melting process become visible and may be allocated anywhere within the 3dim structure. Results of our optical tomography (OT) method as obtained on real defects are presented.

  19. Process-Structure Linkages Using a Data Science Approach: Application to Simulated Additive Manufacturing Data

    International Nuclear Information System (INIS)

    Popova, Evdokia; Rodgers, Theron M.; Gong, Xinyi; Cecen, Ahmet; Madison, Jonathan D.; Kalidindi, Surya R.

    2017-01-01

    A novel data science workflow is developed and demonstrated to extract process-structure linkages (i.e., reduced-order model) for microstructure evolution problems when the final microstructure depends on (simulation or experimental) processing parameters. Our workflow consists of four main steps: data pre-processing, microstructure quantification, dimensionality reduction, and extraction/validation of process-structure linkages. These methods that can be employed within each step vary based on the type and amount of available data. In this paper, this data-driven workflow is applied to a set of synthetic additive manufacturing microstructures obtained using the Potts-kinetic Monte Carlo (kMC) approach. Additive manufacturing techniques inherently produce complex microstructures that can vary significantly with processing conditions. Using the developed workflow, a low-dimensional data-driven model was established to correlate process parameters with the predicted final microstructure. In addition, the modular workflows developed and presented in this work facilitate easy dissemination and curation by the broader community.

  20. The effect of rework content addition on the microstructure and viscoelastic properties of processed cheese.

    Science.gov (United States)

    Černíková, Michaela; Nebesářová, Jana; Salek, Richardos Nikolaos; Popková, Romana; Buňka, František

    2018-04-01

    The aim of this work was to add various amounts of rework (0.0 to 20.0% wt/wt) to processed cheeses with a dry matter content of 36% (wt/wt) and fat with a dry matter content of 45% (wt/wt). The effect of the rework addition on the viscoelastic properties and microstructure of the processed cheeses was observed. The addition of rework (in this case, to processed cheese with a spreadable consistency) in the amounts of 2.5, 5.0, and 10.0% (wt/wt) increased the firmness of the processed cheese. With the further addition of rework, the consistency of the processed cheeses no longer differed significantly. The conclusions obtained by the measurement of viscoelastic properties were supported by cryo-scanning electron microscopy, where fat droplets in samples with added rework of over 10.0% (wt/wt) were smaller than fat droplets in processed cheeses with lower additions of rework. Copyright © 2018 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  1. Process for optimizing titanium and zirconium additions to aluminum welding consumables

    International Nuclear Information System (INIS)

    Dvornak, M.J.; Frost, R.H.

    1992-01-01

    This patent describes a process for manufacturing an aluminum welding consumable. It comprises: creating an aluminum melt; adding to the aluminum melt solid pieces of a master alloy, comprising aluminum and a weld-enhancing additive to form a mixture, wherein the weld-enhancing additive being a material selected from the group consisting of titanium and zirconium, so that the weld-enhancing additive exists in the alloy prior to addition to the melt in the form of intermetallic particles relatively large in size and small in number, and after addition to the melt the weld-enhancing additive exists in the form of fractured intermetallic particles of refined size having dissolved fractured interfaces, casting the mixture into a chill mold to form an ingot; reducing the ingot to rods of rough wire dimension by cold rolling; annealing the reduced rods; and drawing the rods into wire

  2. Application showcases for a small scale membrane contactor for fine chemical processes

    NARCIS (Netherlands)

    Roelands, C.P.M.; Ngene, I.S.

    2011-01-01

    The transition from batch to continuous processing in fine-chemicals industries offers many advantages; among these are a high volumetric productivity, improved control over reaction conditions resulting in a higher yield and selectivity, a small footprint and a safer process due to a smaller

  3. “He lacks his fatherhood”: Safer conception technologies and the biological imperative for fatherhood among recently-diagnosed Xhosa-speaking men living with HIV in South Africa

    Science.gov (United States)

    Taylor, Tonya N.; Mantell, Joanne E.; Nywagi, Ntobeko; Cishe, Nomazizi; Cooper, Diane

    2013-01-01

    This paper explores notions of fatherhood and their linkages to fertility desires and intentions among a treatment-naïve cohort of Xhosa-speaking male key informants living with HIV aged 20-53 in Cape Town, South Africa. Analysis is based on an initial 27 and 20 follow up interviews with men who were part of a study that assessed the acceptability of safer conception and alternative parenting strategies among men and women newly diagnosed with HIV to inform an intervention. Grounded theory analysis revealed themes related to the cultural imperative of biologically-connected fatherhood. Certain safer conception strategies aimed at minimising the risk of HIV transmission were perceived as threats to paternity. These findings suggest that understanding of social and cultural beliefs related to notions of paternity and fatherhood may inform the implementation of acceptable safer conception options for HIV-positive men and their infected and uninfected female partners in a high HIV prevalence, low-resource setting. PMID:23862770

  4. Reactive nanophase oxide additions to melt-processed high-{Tc} superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Goretta, K.C.; Brandel, B.P.; Lanagan, M.T.; Hu, J.; Miller, D.J.; Sengupta, S. [Argonne National Lab., IL (United States); Parker, J.C.; Ali, M.N. [Nanophase Technologies Corp., Darien, IL (United States); Chen, Nan [Illinois Superconductor Corp., Evanston, IL (United States)

    1994-10-01

    Nanophase TiO{sub 2} and Al{sub 2}O{sub 3} powders were synthesized by a vapor-phase process and mechanically mixed with stoichiometric YBa{sub 2}Cu{sub 3}O{sub x} and TlBa{sub 2}Ca{sub 2}Cu{sub 3}O{sub x} powders in 20 mole % concentrations. Pellets produced from powders with and without nanophase oxides were heated in air or O{sub 2} above the peritectic melt temperature and slow-cooled. At 4.2 K, the intragranular critical current density (J{sub c}) increased dramatically with the oxide additions. At 35--50 K, effects of the oxide additions were positive, but less pronounced. At 77 K, the additions decreased J{sub c}, probably because of inducing a depresion of the transition temperature.

  5. Perspectives on the design of safer nanomaterials and manufacturing processes

    International Nuclear Information System (INIS)

    Geraci, Charles; Heidel, Donna; Sayes, Christie; Hodson, Laura; Schulte, Paul; Eastlake, Adrienne; Brenner, Sara

    2015-01-01

    A concerted effort is being made to insert Prevention through Design principles into discussions of sustainability, occupational safety and health, and green chemistry related to nanotechnology. Prevention through Design is a set of principles, which includes solutions to design out potential hazards in nanomanufacturing including the design of nanomaterials, and strategies to eliminate exposures and minimize risks that may be related to the manufacturing processes and equipment at various stages of the lifecycle of an engineered nanomaterial

  6. Perspectives on the design of safer nanomaterials and manufacturing processes

    Energy Technology Data Exchange (ETDEWEB)

    Geraci, Charles [National Institute for Occupational Safety and Health (United States); Heidel, Donna [Bureau Veritas North America, Inc. (United States); Sayes, Christie [Baylor University (United States); Hodson, Laura, E-mail: lhodson@cdc.gov; Schulte, Paul; Eastlake, Adrienne [National Institute for Occupational Safety and Health (United States); Brenner, Sara [Colleges of Nanoscale Science and Engineering at State University of New York Polytechnic Institute, (SUNY Poly) (United States)

    2015-09-15

    A concerted effort is being made to insert Prevention through Design principles into discussions of sustainability, occupational safety and health, and green chemistry related to nanotechnology. Prevention through Design is a set of principles, which includes solutions to design out potential hazards in nanomanufacturing including the design of nanomaterials, and strategies to eliminate exposures and minimize risks that may be related to the manufacturing processes and equipment at various stages of the lifecycle of an engineered nanomaterial.

  7. Small modular reactors: Simpler, safer, cheaper?

    International Nuclear Information System (INIS)

    Vujić, Jasmina; Bergmann, Ryan M.; Škoda, Radek; Miletić, Marija

    2012-01-01

    Nuclear energy can play a very significant long-term role for meeting the world’s increasing energy demands, while simultaneously addressing challenges associated with global climate and environmental impact. Many nations of the world, particularly the Asia/Pacific Rim countries, are actively engaged in a major expansion of their nuclear energy complex. The degree to which nuclear energy can address long-term energy needs, either globally or regionally, will be dictated by the pace and adequacy of technical and policy solutions for waste, safety, security, and non-proliferation issues, as well as the capital cost of construction. Small Modular Reactors (SMRs) could successfully address several of these issues. SMRs offer simpler, standardized, and safer modular design by being factory built, requiring smaller initial capital investment, and having shorter construction times. The SMRs could be small enough to be transportable, could be used in isolated locations without advanced infrastructure and without power grid, or could be clustered in a single site to provide a multi-module, large capacity power plant. This paper summarizes some of the basic features of SMRs for early deployment, several advanced SMR concepts, and points out the benefits and challenges in regulatory, economical, safety and security issues. -- Highlights: ► We held a summer forum on SMR technologies at UC Berkeley in July 2010. ► Advantages and disadvantages, technical and economic, of each design were discussed. ► Further literature searches were also done and this paper summarizes prominent designs. ► We conclude SMRs have no large problems preventing their introduction into the nuclear market.

  8. Additional ion bombardment in PVD processes generated by a superimposed pulse bias voltage

    International Nuclear Information System (INIS)

    Olbrich, W.; Kampschulte, G.

    1993-01-01

    The superimposed pulse bias voltage is a tool to apply an additional ion bombardment during deposition in physical vapour deposition (PVD) processes. It is generated by the combination of a d.c. ground voltage and a higher d.c. pulse voltage. Using a superimposed pulse bias voltage in ion-assisted PVD processes effects an additional all-around ion bombardment on the surface with ions of higher energy. Both metal and reactive or inert-gas ions are accelerated to the surface. The basic principles and important characteristics of this newly developed process such as ion fluxes or deposition rates are shown. Because of pulsing the high voltage, the deposition temperature does not increase much. The adhesion, structure, morphology and internal stresses are influenced by these additional ion impacts. The columnar growth of the deposited films could be suppressed by using the superimposed pulse bias voltage without increasing the deposition temperature. Different metallizations (Cr and Cu) produced by arc and sputter ion plating are investigated. Carbon-fibre-reinforced epoxy are coated with PVD copper films for further treatment in electrochemical processes. (orig.)

  9. Optimization and Prototyping of Medium Pressure Water (MPW) Depaint Process, Tri-Service Committee on Corrosion Proceedings

    National Research Council Canada - National Science Library

    Stropki, John

    1994-01-01

    ... and cleaning of aircraft with hazardous chemicals. The means of determining the viability of this environmentally safer blast process was predicated on establishing a set of process parameters at which paint stripping was accomplished...

  10. The global health law trilogy: towards a safer, healthier, and fairer world.

    Science.gov (United States)

    Gostin, Lawrence O; DeBartolo, Mary Clare; Katz, Rebecca

    2017-10-21

    Global health advocates often turn to medicine and science for solutions to enduring health risks, but law is also a powerful tool. No state acting alone can ward off health threats that span borders, requiring international solutions. A trilogy of global health law-the Framework Convention on Tobacco Control, International Health Regulations (2005), and Pandemic Influenza Preparedness Framework-strives for a safer, healthier, and fairer world. Yet, these international agreements are not well understood, and contain gaps in scope and enforceability. Moreover, major health concerns remain largely unregulated at the international level, such as non-communicable diseases, mental health, and injuries. Here, we offer reforms for this global health law trilogy. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Goneis.gr: Training Greek Parents on ICT and Safer Internet

    Science.gov (United States)

    Manouselis, Nikos; Riviou, Katerina; Palavitsinis, Nikos; Giannikopoulou, Vasiliki; Tsanakas, Panayotis

    Children's use of the Internet has significantly risen in the last decade. Nevertheless, children spend a lot of time online which makes them susceptible to various threats (such as inappropriate material, offensive language, etc). Parents are the last frontier to this menace but they also need to be educated and trained in order to protect their children. Goneis.gr is an initiative launched by the Greek government that aims to educate parents on safer Internet and the use of parental control software. Parents are also entitled to distance learning courses covering basic computer skills. This paper presents the results of two separate surveys that took place in the last few months (December 2008-January 2009). The first survey targeted the parents that have completed the programme and the second one the educational providers that participate in the programme and offer the training to the beneficiaries.

  12. Steamlined Approach for Environmental Restoration (SAFER) Plan For Corrective Action Unit 394: Areas 12, 18, and 29, Spill/Release Sites, Nevada Test Site, Nevada (November 2001, Rev. 0)

    Energy Technology Data Exchange (ETDEWEB)

    U.S. Department of Energy, National Nuclear Security Administration Nevada Operations Office (NNSA/NV)

    2001-09-24

    This plan addresses the actions necessary for the characterization and closure of Corrective Action Unit (CAU) 394: Areas 12, 18, and 29, Spill/Release Sites, identified in the Federal Facility Agreement and Consent Order (FFACO). The CAU, located on the Nevada Test Site, consists of six Corrective Action Sites (CASs): CAS 12-25-04, UST 12-16-2 Waste Oil Release; CAS 18-25-02, Oil Spills; CAS 18-25-02, Oil Spills; CAS 18-25-03, Oil Spill; CAS 18-25-04, Spill (Diesel Fuel); CAS 29-44-01, Fuel Spill (a & b). Process knowledge is the basis for the development of the conceptual site models (CSMs). The CSMs describe the most probable scenario for current conditions at each site, and define the assumptions that are the basis for the SAFER plan. The assumptions are formulated from historical information and process knowledge. Vertical migration of contaminant(s) of potential concern (COPCs) is expected to be predominant over lateral migration in the absence of any barrier (with asphalt /concrete being the exception at least two of the CASs). Soil is the impacted or potentially impacted media at all the sites, with asphalt and/or concrete potentially impacted at two of the CASs. Radionuclides are not expected at any CAS; hydrocarbons are the primary COPC at each CAS, and can be used to guide the investigation; future land-use scenarios limit use to various nonresidential uses; and exposure scenarios are limited by future land-use scenarios to site workers. There is sufficient information and process knowledge from historical documentation regarding the expected nature and extent of potential contaminants to recommend closure of CAU 394 using the SAFER process. On completion of the field activities, a Closure Report will be prepared and submitted to the NDEP for review and approval.

  13. Process to Continuously Melt, Refine and Cast High Quality Steel

    Energy Technology Data Exchange (ETDEWEB)

    None

    2005-09-01

    The purpose of this project is to conduct research and development targeted at designing a revolutionary steelmaking process. This process will deliver high quality steel from scrap to the casting mold in one continuous process and will be safer, more productive, and less capital intensive to build and operate than conventional steelmaking. The new process will produce higher quality steel faster than traditional batch processes while consuming less energy and other resources.

  14. Motives and barriers to safer sex and regular STI testing among MSM soon after HIV diagnosis.

    Science.gov (United States)

    Heijman, Titia; Zuure, Freke; Stolte, Ineke; Davidovich, Udi

    2017-03-07

    Understanding why some recently with HIV diagnosed men who have sex with men (MSM) choose for safer sex and regular STI testing, whereas others do not, is important for the development of interventions that aim to improve the sexual health of those newly infected. To gain insight into motives and barriers to condom use and regular STI testing among MSM soon after HIV diagnosis, 30 HIV-positive MSM participated in semi-structured qualitative interviews on sexual health behaviours in the first year after HIV diagnosis. Typical barriers to condom use soon after diagnosis were emotions such as anger, relief, and feelings of vulnerability. Additional barriers were related to pre-diagnosis patterns of sexual-social behaviour that were difficult to change, communication difficulties, and substance use. Barriers to STI testing revolved around perceptions of low STI risk, faulty beliefs, and burdensome testing procedures. The great diversity of motives and barriers to condom use and STI testing creates a challenge to accommodate newly infected men with information, motivation, and communication skills to match their personal needs. An adaptive, tailored intervention can be a promising tool of support.

  15. Morphology Analysis and Process Research on Novel Metal Fused-coating Additive Manufacturing

    Science.gov (United States)

    Wang, Xin; Wei, Zheng ying; Du, Jun; Ren, Chuan qi; Zhang, Shan; Zhang, Zhitong; Bai, Hao

    2017-12-01

    Existing metal additive manufacturing equipment has high capital costs and slow throughput printing. In this paper, a new metal fused-coating additive manufacturing (MFCAM) was proposed. Experiments of single-track formation were conducted using MFCAM to validate the feasibility. The low melting alloy was selected as the forming material. Then, the effect of process parameters such as the flow rate, deposition velocity and initial distance on the forming morphology. There is a strong coupling effect between the single track forming morphology. Through the analysis of influencing factors to improve the forming quality of specimens. The experimental results show that the twice as forming efficiency as the metal droplet deposition. Additionally, the forming morphology and quality were analyzed by confocal laser scanning microscope and X-ray. The results show that the metal fused-coating process can achieve good surface morphology and without internal tissue defect.

  16. Process Modeling and Validation for Metal Big Area Additive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Simunovic, Srdjan [ORNL; Nycz, Andrzej [ORNL; Noakes, Mark W. [ORNL; Chin, Charlie [Dassault Systemes; Oancea, Victor [Dassault Systemes

    2017-05-01

    Metal Big Area Additive Manufacturing (mBAAM) is a new additive manufacturing (AM) technology based on the metal arc welding. A continuously fed metal wire is melted by an electric arc that forms between the wire and the substrate, and deposited in the form of a bead of molten metal along the predetermined path. Objects are manufactured one layer at a time starting from the base plate. The final properties of the manufactured object are dependent on its geometry and the metal deposition path, in addition to depending on the basic welding process parameters. Computational modeling can be used to accelerate the development of the mBAAM technology as well as a design and optimization tool for the actual manufacturing process. We have developed a finite element method simulation framework for mBAAM using the new features of software ABAQUS. The computational simulation of material deposition with heat transfer is performed first, followed by the structural analysis based on the temperature history for predicting the final deformation and stress state. In this formulation, we assume that two physics phenomena are coupled in only one direction, i.e. the temperatures are driving the deformation and internal stresses, but their feedback on the temperatures is negligible. The experiment instrumentation (measurement types, sensor types, sensor locations, sensor placements, measurement intervals) and the measurements are presented. The temperatures and distortions from the simulations show good correlation with experimental measurements. Ongoing modeling work is also briefly discussed.

  17. Generalised additive modelling approach to the fermentation process of glutamate.

    Science.gov (United States)

    Liu, Chun-Bo; Li, Yun; Pan, Feng; Shi, Zhong-Ping

    2011-03-01

    In this work, generalised additive models (GAMs) were used for the first time to model the fermentation of glutamate (Glu). It was found that three fermentation parameters fermentation time (T), dissolved oxygen (DO) and oxygen uptake rate (OUR) could capture 97% variance of the production of Glu during the fermentation process through a GAM model calibrated using online data from 15 fermentation experiments. This model was applied to investigate the individual and combined effects of T, DO and OUR on the production of Glu. The conditions to optimize the fermentation process were proposed based on the simulation study from this model. Results suggested that the production of Glu can reach a high level by controlling concentration levels of DO and OUR to the proposed optimization conditions during the fermentation process. The GAM approach therefore provides an alternative way to model and optimize the fermentation process of Glu. Crown Copyright © 2010. Published by Elsevier Ltd. All rights reserved.

  18. “I don’t know if this is right…but this is what I’m offering”: Healthcare provider knowledge, practice, and attitudes towards safer conception for HIV-affected couples in the context of Southern African guidelines

    Science.gov (United States)

    Schwartz, Sheree; Phofa, Rebecca; Yende, Nompumelelo; Bassett, Jean; Sanne, Ian; Van Rie, Annelies

    2016-01-01

    The 2011 guidelines for safer conception for HIV-affected individuals and couples were adopted by the South African Department of Health in December 2012. We assessed implementation gaps and facilitators and barriers to delivering safer conception services through examining patient and healthcare provider (HCP) experiences. At Witkoppen Health and Welfare Centre, a primary care clinic in Johannesburg, we conducted in-depth interviews (IDIs) with 9 HCPs (doctors, nurses and counselors) and IDIs and focus group discussions with 42 HIV-affected men and women interested in having a child. Data were analyzed using a grounded theory approach. HCPs were supportive of fertility intentions of HIV-affected couples and demonstrated some knowledge of safer conception methods, especially ART initiation to suppress viral load in infected partners. Unfortunately, HCPs did not follow the key recommendation that HCPs initiate conversations on fertility intentions with HIV-affected men and women. Providers and clients reported that conversations about conception only occur when client-initiated, placing the onus on HIV-affected individuals. Important barriers underlying this were the misconception held by some HCPs that uninfected partners in serodiscordant partnerships are “latently” infected and the desire by most HCPs to protect or control knowledge around fertility and safer conception methods out of concern over what clients will do with this knowledge before they are virally suppressed or ready to conceive. Almost all participants who had conceived or attempted conception did so without safer conception methods knowledge. HCP concern over conception readiness, perception of what clients will do with safer conception knowledge, and gaps in safer conception knowledge prevent HCPs from initiating conversations with HIV-affected patients on the issue of childbearing. Examining these findings in the context of existing South African guidelines illuminates areas that need to be

  19. Safer sex decision-making among men with haemophilia and HIV and their female partners.

    Science.gov (United States)

    Parish, K L; Cotton, D; Huszti, H C; Parsons, J T

    2001-01-01

    An exploratory qualitative study of adult heterosexual men with haemophilia and HIV and women who were their sexual partners was conducted as formative research to better understand cognitive factors involved in behavioural intentions and practices which comprise HIV risk-reduction for sexual transmission. The study sought to generate hypotheses, uncover themes, and develop a broad perspective on possible determinants of behaviours related to HIV transmission risk reduction. Qualitative analysis of these data served as a basis for developing a subsequent quantitative, hypothesis-testing survey and an intervention. Face-to-face interviews were conducted with 23 single men and 28 married men with haemophilia and HIV infection, and 28 married women partners selected through stratified, purposeful sampling. The interviews identified beliefs, attitudes, and values underlying decisions regarding target behaviours related to preventing sexual transmission of HIV, including (1) using condoms consistently during vaginal intercourse and (2) talking to partners about risk reduction. The interviews elicited information about perceived advantages and disadvantages of performing each of the targeted behaviours, and factors that facilitate or prevent performing them. Qualitative analysis of coded responses yielded important themes regarding how choices are made about sexual activity and safer sex. Most notably, communication between partners (1) plays a direct, key role in facilitating condom use and (2) forms the basis for maintaining emotional intimacy in these relationships. The link between condom use and communicating about safer sex was viewed as pivotal in achieving HIV prevention for individuals in serodiscordant couples. Recommendations for risk reduction intervention development are discussed.

  20. Steamlined Approach for Environmental Restoration (SAFER) Plan For Corrective Action Unit 394: Areas 12, 18, and 29, Spill/Release Sites, Nevada Test Site, Nevada (November 2001, Rev. 0); FINAL

    International Nuclear Information System (INIS)

    2001-01-01

    This plan addresses the actions necessary for the characterization and closure of Corrective Action Unit (CAU) 394: Areas 12, 18, and 29, Spill/Release Sites, identified in the Federal Facility Agreement and Consent Order (FFACO). The CAU, located on the Nevada Test Site, consists of six Corrective Action Sites (CASs): CAS 12-25-04, UST 12-16-2 Waste Oil Release; CAS 18-25-02, Oil Spills; CAS 18-25-02, Oil Spills; CAS 18-25-03, Oil Spill; CAS 18-25-04, Spill (Diesel Fuel); CAS 29-44-01, Fuel Spill (a and b). Process knowledge is the basis for the development of the conceptual site models (CSMs). The CSMs describe the most probable scenario for current conditions at each site, and define the assumptions that are the basis for the SAFER plan. The assumptions are formulated from historical information and process knowledge. Vertical migration of contaminant(s) of potential concern (COPCs) is expected to be predominant over lateral migration in the absence of any barrier (with asphalt /concrete being the exception at least two of the CASs). Soil is the impacted or potentially impacted media at all the sites, with asphalt and/or concrete potentially impacted at two of the CASs. Radionuclides are not expected at any CAS; hydrocarbons are the primary COPC at each CAS, and can be used to guide the investigation; future land-use scenarios limit use to various nonresidential uses; and exposure scenarios are limited by future land-use scenarios to site workers. There is sufficient information and process knowledge from historical documentation regarding the expected nature and extent of potential contaminants to recommend closure of CAU 394 using the SAFER process. On completion of the field activities, a Closure Report will be prepared and submitted to the NDEP for review and approval

  1. The Polymeal: a more natural, safer, and probably tastier (than the Polypill) strategy to reduce cardiovascular disease by more than 75%

    NARCIS (Netherlands)

    O.H. Franco (Oscar); L.G.A. Bonneux (Luc); C.E.D. de Laet (Chris); A. Peeters (Anna); E.W. Steyerberg (Ewout); J.P. Mackenbach (Johan)

    2004-01-01

    textabstractOBJECTIVE: Although the Polypill concept (proposed in 2003) is promising in terms of benefits for cardiovascular risk management, the potential costs and adverse effects are its main pitfalls. The objective of this study was to identify a tastier and safer

  2. QUALITY OF MINIMALLY PROCESSED ‘FUJI’ APPLE UNDER REFRIGERATED STORAGE AND TREATMENT WITH ADDITIVES

    Directory of Open Access Journals (Sweden)

    MARINES BATALHA MORENO

    Full Text Available ABSTRACT The aim of this study was to evaluate the ability to prolong the useful life of the minimally processed ‘Fuji’ apple by applying the individual or combined additives (L-cysteine chloride, L-ascorbic acid and calcium chloride and to determine the appropriate period of storage of the whole fruit to perform the minimum processing. The experimental design was completely randomized in three-factor design with three replications. Factor A was composed of storage periods of whole apples, pre-processing, in cold chambers (20, 78, 138 and 188 days; the factor B was represented by storage periods minimum post-processing, simulating shelf life (3, 6, 9 and 12 days, and factor C was represented by chemical additives (distilled water, as control, 0.5% L-cysteine chloride, 1% L-ascorbic acid, 0.5% L-cysteine chloride along with 1% calcium chloride and 1% L-ascorbic acid together with 1% calcium chloride. The evaluated dependent variables were pulp color (L* and hº, soluble solids, titratable acidity, content of phenolic compounds, antioxidant capacity and quantification of polyphenol oxidase. In addition, was analyzed the presence or absence of Salmonella sp. and Escherichia coli. The prolongation of the storage time of ‘Fuji’ apples in a refrigerated atmosphere promotes increased susceptibility to browning and softening after processing from 78 days of storage. The use of additives in the process, helps prevent these problems, especially when combined 0.5% L-cysteine chloride with 1% calcium chloride, achieving an excellent conservation in refrigerated shelf up to 6 days. From a microbiological aspect, minimally processed apples are toxicologically safe.

  3. Multi-level Correlates of Safer Conception Methods Awareness and Attitudes Among Ugandan HIV Clients with Fertility Intentions

    OpenAIRE

    Wagner, Glenn J.; Woldetsadik, Mahlet A.; Beyeza-Kashesya, Jolly; Goggin, Kathy; Mindry, Deborah; Finocchario-Kessler, Sarah; Khanakwa, Sarah; Wanyenze, Rhoda K.

    2016-01-01

    Many people living with HIV desire childbearing, but low cost safer conception methods (SCM) such as timed unprotected intercourse (TUI) and manual self-insemination (MSI) are rarely used. We examined awareness and attitudes towards SCM, and the correlates of these constructs among 400 HIV clients with fertility intentions in Uganda. Measures included awareness, self-efficacy, and motivation regarding SCM, as well as demographics, health management, partner and provider characteristics. Just ...

  4. Association between 'safer sex fatigue' and rectal gonorrhea is mediated by unsafe sex with casual partners among HIV-positive homosexual men.

    NARCIS (Netherlands)

    Stolte, Ineke G; Wit, John B F de; Kolader, Marion-Eliëtte; Fennema, Johan S A; Coutinho, Roel A; Dukers, Nicole H T M

    2006-01-01

    OBJECTIVE: The objective of this study was to investigate whether and what sexual risk behavior is a mediator of associations between rectal gonorrhea (RG) and highly active antiretroviral therapy-related beliefs, safer sex fatigue, or sexual sensation-seeking among homosexual men. STUDY DESIGN:

  5. Association between 'safer sex fatigue' and rectal gonorrhea is mediated by unsafe sex with casual partners among HIV-positive homosexual men

    NARCIS (Netherlands)

    Stolte, Ineke G.; de Wit, John B. F.; Kolader, Marion; Fennema, Han; Coutinho, Roel A.; Dukers, Nicole H. T. M.

    2006-01-01

    OBJECTIVE: The objective of this study was to investigate whether and what sexual risk behavior is a mediator of associations between rectal gonorrhea (RG) and highly active antiretroviral therapy-related beliefs, safer sex fatigue, or sexual sensation-seeking among homosexual men. STUDY DESIGN:

  6. "I don't know if this is right … but this is what I'm offering": healthcare provider knowledge, practice, and attitudes towards safer conception for HIV-affected couples in the context of Southern African guidelines.

    Science.gov (United States)

    West, Nora; Schwartz, Sheree; Phofa, Rebecca; Yende, Nompumelelo; Bassett, Jean; Sanne, Ian; Van Rie, Annelies

    2016-01-01

    The 2011 guidelines for safer conception for HIV-affected individuals and couples were adopted by the South African Department of Health in December 2012. We assessed implementation gaps and facilitators and barriers to delivering safer conception services through examining patient and healthcare provider (HCP) experiences. At Witkoppen Health and Welfare Centre, a primary care clinic in Johannesburg, we conducted in-depth interviews (IDIs) with nine HCPs (doctors, nurses, and counselors) and IDIs and focus group discussions with 42 HIV-affected men and women interested in having a child. Data were analyzed using a grounded theory approach. HCPs were supportive of fertility intentions of HIV-affected couples and demonstrated some knowledge of safer conception methods, especially ART initiation to suppress viral load in infected partners. Unfortunately, HCPs did not follow the key recommendation that HCPs initiate conversations on fertility intentions with HIV-affected men and women. Providers and clients reported that conversations about conception only occur when client-initiated, placing the onus on HIV-affected individuals. Important barriers underlying this were the misconception held by some HCPs that uninfected partners in serodiscordant partnerships are "latently" infected and the desire by most HCPs to protect or control knowledge around fertility and safer conception methods out of concern over what clients will do with this knowledge before they are virally suppressed or ready to conceive. Almost all participants who had conceived or attempted conception did so without safer conception methods knowledge. HCP concern over conception readiness, perception of what clients will do with safer conception knowledge, and gaps in safer conception knowledge prevent HCPs from initiating conversations with HIV-affected patients on the issue of childbearing. Examining these findings in the context of existing South African guidelines illuminates areas that need to be

  7. ïSCOPE: Safer care for older persons (in residential environments: A study protocol

    Directory of Open Access Journals (Sweden)

    Barnard Debbie

    2011-07-01

    Full Text Available Abstract Background The current profile of residents living in Canadian nursing homes includes elder persons with complex physical and social needs. High resident acuity can result in increased staff workload and decreased quality of work life. Aims Safer Care for Older Persons [in residential] Environments is a two year (2010 to 2012 proof-of-principle pilot study conducted in seven nursing homes in western Canada. The purpose of the study is to evaluate the feasibility of engaging front line staff to use quality improvement methods to integrate best practices into resident care. The goals of the study are to improve the quality of work life for staff, in particular healthcare aides, and to improve residents' quality of life. Methods/design The study has parallel research and quality improvement intervention arms. It includes an education and support intervention for direct caregivers to improve the safety and quality of their care delivery. We hypothesize that this intervention will improve not only the care provided to residents but also the quality of work life for healthcare aides. The study employs tools adapted from the Institute for Healthcare Improvement's Breakthrough Series: Collaborative Model and Canada's Safer Healthcare Now! improvement campaign. Local improvement teams in each nursing home (1 to 2 per facility are led by healthcare aides (non-regulated caregivers and focus on the management of specific areas of resident care. Critical elements of the program include local measurement, virtual and face-to-face learning sessions involving change management, quality improvement methods and clinical expertise, ongoing virtual and in person support, and networking. Discussion There are two sustainability challenges in this study: ongoing staff and leadership engagement, and organizational infrastructure. Addressing these challenges will require strategic planning with input from key stakeholders for sustaining quality improvement

  8. A Pilot Model for the NASA Simplified Aid for EVA Rescue (SAFER) (Single-Axis Pitch Task)

    Science.gov (United States)

    Handley, Patrick Mark

    This thesis defines, tests, and validates a descriptive pilot model for a single-axis pitch control task of the Simplified Aid for EVA Rescue (SAFER). SAFER is a small propulsive jetpack used by astronauts for self-rescue. Pilot model research supports development of improved self-rescue strategies and technologies through insights into pilot behavior.This thesis defines a multi-loop pilot model. The innermost loop controls the hand controller, the middle loop controls pitch rate, and the outer loop controls pitch angle. A human-in-the-loop simulation was conducted to gather data from a human pilot. Quantitative and qualitative metrics both indicate that the model is an acceptable fit to the human data. Fuel consumption was nearly identical; time to task completion matched very well. There is some evidence that the model responds faster to initial pitch rates than the human, artificially decreasing the model's time to task completion. This pilot model is descriptive, not predictive, of the human pilot. Insights are made into pilot behavior from this research. Symmetry implies that the human responds to positive and negative initial conditions with the same strategy. The human pilot appears indifferent to pitch angles within 0.5 deg, coasts at a constant pitch rate 1.09 deg/s, and has a reaction delay of 0.1 s.

  9. Using a service design model to develop the "Passport to Safer Birth" in Nigeria and Uganda.

    Science.gov (United States)

    Salgado, Mariana; Wendland, Melanie; Rodriguez, Damaris; Bohren, Meghan A; Oladapo, Olufemi T; Ojelade, Olubunmi A; Olalere, Adebimpe A; Luwangula, Ronald; Mugerwa, Kidza; Fawole, Bukola

    2017-12-01

    To demonstrate how a human-centered service design approach can generate practical tools for good-quality childbirth care in low-resource settings. As part of the WHO "Better Outcomes in Labour Difficulty" (BOLD) project, a service design approach was used in eight Ugandan and Nigerian health facilities and communities to develop the "Passport to Safer Birth." There are three phases: Research for Design, Concept Design, and Detail Design. These generated design principles, design archetype personas, and Passport prototypes. Data collection methods included desk research, interviews, group discussions, and journey mapping to identify touchpoints where the woman interacts with the health system. A total of 90 interviews, 12 observation hours, and 15 group discussions were undertaken. The resulting design principles were: a shared and deeper understanding of pregnancy and childbirth among family and community; family readiness for decision-making and action; and the woman's sense of being in control and being cared for. Four archetype personas of women emerged: Vulnerable; Passive; Empowered; Accepter. Subsequent development of the Passport to Safer Birth tools addressed three domains: Care Mediator; Expectation Manager; and Pregnancy Assistant. The service design approach can create innovative, human-centered service solutions to improve maternity care experiences and outcomes in low-resource settings. © 2017 International Federation of Gynecology and Obstetrics The World Health Organization retains copyright and all other rights in the manuscript of this article as submitted for publication.

  10. A mechanistic understanding of processing additive-induced efficiency enhancement in bulk heterojunction organic solar cells

    KAUST Repository

    Schmidt, Kristin; Tassone, Christopher J.; Niskala, Jeremy R.; Yiu, Alan T.; Lee, Olivia P.; Weiss, Thomas M.; Wang, Cheng; Frechet, Jean; Beaujuge, Pierre; Toney, Michael F.

    2013-01-01

    The addition of processing additives is a widely used approach to increase power conversion efficiencies for many organic solar cells. We present how additives change the polymer conformation in the casting solution leading to a more intermixed

  11. Evaluation of the California Safer Consumer Products Regulation and the impact on consumers and product manufacturers.

    Science.gov (United States)

    Cowan, Dallas M; Kingsbury, Tony; Perez, Angela L; Woods, Tyler A; Kovochich, Michael; Hill, Denise S; Madl, Amy K; Paustenbach, Dennis J

    2014-02-01

    Chemistry enables more than 95% of products in the marketplace. Over the past 20 years, various entities began to generate inventories of chemicals ("chemical watch lists") potentially associated with human or environmental health risks. Some lists included thousands of chemicals, while others listed only a few chemistries with limited properties or toxicological endpoints (e.g., neurotoxicants). Enacted on October 1, 2013, the California Safer Consumer Products Regulation (SCP) utilized data from chemical inventory lists to create one master list. This paper aims to discuss the background and requirements of this regulation. Additionally, we wanted to understand the universe of Candidate Chemicals identified by the Regulation. Data from all 23 chemical lists identified in the SCP Regulation were entered into a database. The most prevalent chemicals among the ∼2900 chemicals are identified, including the most prevalent chemical, lead, appearing on 65% of lists, followed by DEHP (52%), perchloroethylene (48%), and benzene (48%). Our results indicated that the most prevalent Candidate Chemicals were either persistent, bioaccumulative, carcinogenic, or reprotoxic. This regulation will have wide-ranging impact in California and throughout the global supply chain, which is highlighted through selected examples and case studies. Copyright © 2013 Elsevier Inc. All rights reserved.

  12. Expediting Groundwater Sampling at Hanford and Making It Safer - 13158

    International Nuclear Information System (INIS)

    Connell, Carl W. Jr.; Conley, S.F.; Carr, Jennifer S.; Schatz, Aaron L.; Brown, W.L.; Hildebrand, R. Douglas

    2013-01-01

    documents, the system saves three-to-four man days each month for the field personnel taking the measurements and the scientists and administrators managing the data and the documentation. After the information has received technical review, FLEDG automatically updates the database for water-level measurements and loads the document management system with the completed sampling report. Due to safety considerations, access to wells is conditional. A spreadsheet with appropriate data not only lists the wells that are cleared for work, but also the safety personnel who must be present before work can start. This spreadsheet is used in planning daily activities. Daily plans are structured to ensure that the wells to be sampled are cleared for work and the appropriate safety personnel have been assigned and are present before the work starts. Historically, the spreadsheets have been prepared manually, and as a result, are potentially subject to human error. However, a companion database application has been developed to work with FLEDG - making the entire sampling process more efficient and safer for personnel. The Well Access List - Electronic, WAL-E, is a database that contains much the same information that was previously manually loaded into the spread sheet. In addition, WAL-E contains a managed work-flow application that shows the access requirements and allows for appropriate reviews of the compiled well. Various CHPRC organizations, including Industrial Hygiene, RADCON, and Well Maintenance and Sample Administration are able to enter and review the wells added or deleted from the WAL-E database. The FLEDG system then accesses this database information to identify appropriate support personnel and provide safety requirements to field personnel. In addition, WAL-E offers the assurance that wells have appropriate locks and are correctly labeled and electrically grounded as required, before well activities begin. This feature is an extremely important aspect of the FLEDG

  13. Expediting Groundwater Sampling at Hanford and Making It Safer - 13158

    Energy Technology Data Exchange (ETDEWEB)

    Connell, Carl W. Jr.; Conley, S.F.; Carr, Jennifer S.; Schatz, Aaron L. [CH2M HILL Plateau Remediation Company, P.O. Box 1600, Richland, WA 99352 (United States); Brown, W.L. [Lockheed Martin Systems Information, P.O. Box 950, Richland, WA 99352 (United States); Hildebrand, R. Douglas [Department of Energy - Richland Operations Office, 825 Jadwin Ave., Richland, WA 99352 (United States)

    2013-07-01

    eliminating the need to print out documents, the system saves three-to-four man days each month for the field personnel taking the measurements and the scientists and administrators managing the data and the documentation. After the information has received technical review, FLEDG automatically updates the database for water-level measurements and loads the document management system with the completed sampling report. Due to safety considerations, access to wells is conditional. A spreadsheet with appropriate data not only lists the wells that are cleared for work, but also the safety personnel who must be present before work can start. This spreadsheet is used in planning daily activities. Daily plans are structured to ensure that the wells to be sampled are cleared for work and the appropriate safety personnel have been assigned and are present before the work starts. Historically, the spreadsheets have been prepared manually, and as a result, are potentially subject to human error. However, a companion database application has been developed to work with FLEDG - making the entire sampling process more efficient and safer for personnel. The Well Access List - Electronic, WAL-E, is a database that contains much the same information that was previously manually loaded into the spread sheet. In addition, WAL-E contains a managed work-flow application that shows the access requirements and allows for appropriate reviews of the compiled well. Various CHPRC organizations, including Industrial Hygiene, RADCON, and Well Maintenance and Sample Administration are able to enter and review the wells added or deleted from the WAL-E database. The FLEDG system then accesses this database information to identify appropriate support personnel and provide safety requirements to field personnel. In addition, WAL-E offers the assurance that wells have appropriate locks and are correctly labeled and electrically grounded as required, before well activities begin. This feature is an extremely

  14. Electric poling-assisted additive manufacturing process for PVDF polymer-based piezoelectric device applications

    International Nuclear Information System (INIS)

    Lee, ChaBum; Tarbutton, Joshua A

    2014-01-01

    This paper presents a new additive manufacturing (AM) process to directly and continuously print piezoelectric devices from polyvinylidene fluoride (PVDF) polymeric filament rods under a strong electric field. This process, called ‘electric poling-assisted additive manufacturing or EPAM, combines AM and electric poling processes and is able to fabricate free-form shape piezoelectric devices continuously. In this process, the PVDF polymer dipoles remain well-aligned and uniform over a large area in a single design, production and fabrication step. During EPAM process, molten PVDF polymer is simultaneously mechanically stresses in-situ by the leading nozzle and electrically poled by applying high electric field under high temperature. The EPAM system was constructed to directly print piezoelectric structures from PVDF polymeric filament while applying high electric field between nozzle tip and printing bed in AM machine. Piezoelectric devices were successfully fabricated using the EPAM process. The crystalline phase transitions that occurred from the process were identified by using the Fourier transform infrared spectroscope. The results indicate that devices printed under a strong electric field become piezoelectric during the EPAM process and that stronger electric fields result in greater piezoelectricity as marked by the electrical response and the formation of sharper peaks at the polar β crystalline wavenumber of the PVDF polymer. Performing this process in the absence of an electric field does not result in dipole alignment of PVDF polymer. The EPAM process is expected to lead to the widespread use of AM to fabricate a variety of piezoelectric PVDF polymer-based devices for sensing, actuation and energy harvesting applications with simple, low cost, single processing and fabrication step. (paper)

  15. Evaluation of polymer micro parts produced by additive manufacturing processes using vat photopolymerization method

    DEFF Research Database (Denmark)

    Davoudinejad, Ali; Pedersen, David Bue; Tosello, Guido

    2017-01-01

    Micro manufacturing scale feature production by Additive Manufacturing (AM) processes for the direct production of miniaturized polymer components is analysed in this work. The study characterizes the AM processes for polymer micro parts productions using the vat photopolymerization method...

  16. Physical evaluations of Co-Cr-Mo parts processed using different additive manufacturing techniques

    Science.gov (United States)

    Ghani, Saiful Anwar Che; Mohamed, Siti Rohaida; Harun, Wan Sharuzi Wan; Noar, Nor Aida Zuraimi Md

    2017-12-01

    In recent years, additive manufacturing with highly design customization has gained an important technique for fabrication in aerospace and medical fields. Despite the ability of the process to produce complex components with highly controlled architecture geometrical features, maintaining the part's accuracy, ability to fabricate fully functional high density components and inferior surfaces quality are the major obstacles in producing final parts using additive manufacturing for any selected application. This study aims to evaluate the physical properties of cobalt chrome molybdenum (Co-Cr-Mo) alloys parts fabricated by different additive manufacturing techniques. The full dense Co-Cr-Mo parts were produced by Selective Laser Melting (SLM) and Direct Metal Laser Sintering (DMLS) with default process parameters. The density and relative density of samples were calculated using Archimedes' principle while the surface roughness on the top and side surface was measured using surface profiler. The roughness average (Ra) for top surface for SLM produced parts is 3.4 µm while 2.83 µm for DMLS produced parts. The Ra for side surfaces for SLM produced parts is 4.57 µm while 9.0 µm for DMLS produced parts. The higher Ra values on side surfaces compared to the top faces for both manufacturing techniques was due to the balling effect phenomenon. The yield relative density for both Co-Cr-Mo parts produced by SLM and DMLS are 99.3%. Higher energy density has influence the higher density of produced samples by SLM and DMLS processes. The findings of this work demonstrated that SLM and DMLS process with default process parameters have effectively produced full dense parts of Co-Cr-Mo with high density, good agreement of geometrical accuracy and better surface finish. Despite of both manufacturing process yield that produced components with higher density, the current finding shows that SLM technique could produce components with smoother surface quality compared to DMLS

  17. Effective healthcare process redesign through an interdisciplinary team approach.

    Science.gov (United States)

    Snyder, Rita; Huynh, Nathan; Cai, Bo; Vidal, José; Bennett, Kevin

    2013-01-01

    Healthcare process redesign is a complex and often high risk undertaking. Typically, there is a limited understanding of the baseline process and often inadequate tools by which to assess it. This can be confounded by narrow redesign team expertise that can result in unanticipated and/or unintended redesign consequences. Interdisciplinary research teams of healthcare, biostatistics, engineering and computer science experts provide broad support for a more effective and safer approach to healthcare process redesign. We describe an interdisciplinary research team focused on medication administration process (MAP)redesign and its achievements and challenges.

  18. Multiple High-Fidelity Modeling Tools for Metal Additive Manufacturing Process Development, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Despite the rapid commercialization of additive manufacturing technology such as selective laser melting, SLM, there are gaps in process modeling and material...

  19. Multiple High-Fidelity Modeling Tools for Metal Additive Manufacturing Process Development, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — Despite the rapid commercialization of additive manufacturing technology such as selective laser melting, SLM, there are gaps in process modeling and material...

  20. Microbial additives in the composting process

    Directory of Open Access Journals (Sweden)

    Noelly de Queiroz Ribeiro

    Full Text Available ABSTRACT Composting is the process of natural degradation of organic matter carried out by environmental microorganisms whose metabolic activities cause the mineralization and partial humification of substances in the pile. This compost can be beneficially applied to the soil as organic fertilizer in horticulture and agriculture. The number of studies involving microbial inoculants has been growing, and they aim to improve processes such as composting. However, the behavior of these inoculants and other microorganisms during the composting process have not yet been described. In this context, this work aimed to investigate the effects of using a microbial inoculum that can improve the composting process and to follow the bacterial population dynamics throughout the process using the high-resolution melt (HRM technique. To do so, we analysed four compost piles inoculated with Bacillus cereus, Bacillus megaterium, B. cereus + B. megaterium and a control with no inoculum. The analyses were carried out using samples collected at different stages of the process (5th to 110th days. The results showed that the bacterial inocula influenced the process of composting, altering the breakdown of cellulose and hemicelluloses and causing alterations to the temperature and nitrogen levels throughout the composting process. The use of a universal primer (rDNA 16S allowed to follow the microbial succession during the process. However, the design of a specific primer is necessary to follow the inoculum throughout the composting process with more accuracy.

  1. Safer disclosure of HIV serostatus for women living with HIV who experience or fear violence: a systematic review

    OpenAIRE

    Kennedy, Caitlin E; Haberlen, Sabina; Amin, Avni; Baggaley, Rachel; Narasimhan, Manjulaa

    2015-01-01

    Introduction: Supporting individuals as they disclose their HIV serostatus may lead to a variety of individual and public health benefits. However, many women living with HIV are hesitant to disclose their HIV status due to fear of negative outcomes such as violence, abandonment, relationship dissolution and stigma. Methods: We conducted a systematic review of studies evaluating interventions to facilitate safer disclosure of HIV status for women living with HIV who experience or fear violenc...

  2. Electroacoustics modeling of piezoelectric welders for ultrasonic additive manufacturing processes

    Science.gov (United States)

    Hehr, Adam; Dapino, Marcelo J.

    2016-04-01

    Ultrasonic additive manufacturing (UAM) is a recent 3D metal printing technology which utilizes ultrasonic vibrations from high power piezoelectric transducers to additively weld similar and dissimilar metal foils. CNC machining is used intermittent of welding to create internal channels, embed temperature sensitive components, sensors, and materials, and for net shaping parts. Structural dynamics of the welder and work piece influence the performance of the welder and part quality. To understand the impact of structural dynamics on UAM, a linear time-invariant model is used to relate system shear force and electric current inputs to the system outputs of welder velocity and voltage. Frequency response measurements are combined with in-situ operating measurements of the welder to identify model parameters and to verify model assumptions. The proposed LTI model can enhance process consistency, performance, and guide the development of improved quality monitoring and control strategies.

  3. Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control.

    Science.gov (United States)

    Slotwinski, John A; Garboczi, Edward J; Hebenstreit, Keith M

    2014-01-01

    Additive manufacturing techniques can produce complex, high-value metal parts, with potential applications as critical metal components such as those found in aerospace engines and as customized biomedical implants. Material porosity in these parts is undesirable for aerospace parts - since porosity could lead to premature failure - and desirable for some biomedical implants - since surface-breaking pores allows for better integration with biological tissue. Changes in a part's porosity during an additive manufacturing build may also be an indication of an undesired change in the build process. Here, we present efforts to develop an ultrasonic sensor for monitoring changes in the porosity in metal parts during fabrication on a metal powder bed fusion system. The development of well-characterized reference samples, measurements of the porosity of these samples with multiple techniques, and correlation of ultrasonic measurements with the degree of porosity are presented. A proposed sensor design, measurement strategy, and future experimental plans on a metal powder bed fusion system are also presented.

  4. Bistatic sAR data processing algorithms

    CERN Document Server

    Qiu, Xiaolan; Hu, Donghui

    2013-01-01

    Synthetic Aperture Radar (SAR) is critical for remote sensing. It works day and night, in good weather or bad. Bistatic SAR is a new kind of SAR system, where the transmitter and receiver are placed on two separate platforms. Bistatic SAR is one of the most important trends in SAR development, as the technology renders SAR more flexible and safer when used in military environments. Imaging is one of the most difficult and important aspects of bistatic SAR data processing. Although traditional SAR signal processing is fully developed, bistatic SAR has a more complex system structure, so sign

  5. Quantitative Risk Analysis of a Pervaporation Process for Concentrating Hydrogen Peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Ho Jin; Yoon, Ik Keun [Korea Gas Corporation, Ansan (Korea, Republic of); Choi, Soo Hyoung [Chonbuk National University, Jeonju (Korea, Republic of)

    2014-12-15

    Quantitative risk analysis has been performed for a pervaporation process for production of high test peroxide. Potential main accidents are explosion and fire caused by a decomposition reaction. As the target process has a laboratory scale, the consequence is considered to belong to Category 3. An event tree has been developed as a model for occurrence of a decomposition reaction in the target process. The probability functions of the accident causes have been established based on the frequency data of similar events. Using the constructed model, the failure rate has been calculated. The result indicates that additional safety devices are required in order to achieve an acceptable risk level, i.e. an accident frequency less than 10{sup -4}/yr. Therefore, a layer of protection analysis has been applied. As a result, it is suggested to introduce inherently safer design to avoid catalytic reaction, a safety instrumented function to prevent overheating, and a relief system that prevents explosion even if a decomposition reaction occurs. The proposed method is expected to contribute to developing safety management systems for various chemical processes including concentration of hydrogen peroxide.

  6. Post Processing Methods used to Improve Surface Finish of Products which are Manufactured by Additive Manufacturing Technologies: A Review

    Science.gov (United States)

    Kumbhar, N. N.; Mulay, A. V.

    2016-08-01

    The Additive Manufacturing (AM) processes open the possibility to go directly from Computer-Aided Design (CAD) to a physical prototype. These prototypes are used as test models before it is finalized as well as sometimes as a final product. Additive Manufacturing has many advantages over the traditional process used to develop a product such as allowing early customer involvement in product development, complex shape generation and also save time as well as money. Additive manufacturing also possess some special challenges that are usually worth overcoming such as Poor Surface quality, Physical Properties and use of specific raw material for manufacturing. To improve the surface quality several attempts had been made by controlling various process parameters of Additive manufacturing and also applying different post processing techniques on components manufactured by Additive manufacturing. The main objective of this work is to document an extensive literature review in the general area of post processing techniques which are used in Additive manufacturing.

  7. Food additives used in meat processing according to the Polish and European Union legislation.

    Science.gov (United States)

    Uradziński, J; Weiner, M

    2003-01-01

    This paper presents the legal regulations related to the use of food additives in meat production in Poland and the European Union. The Polish legal definition of food additives is given as well as the classification of permitted food additives added to food and stimulants by their technological function. In addition, a definition of processing aids in the food industry is included. It shows that Polish legislation includes food additives used to ensure or improve food nutritional value, whereas in the EU legislation, these substances are not included in the list of food additives. Moreover, the Council Directives include food additive specific purity criteria, whereas the Polish regulations do not mention the legal regulations of this issue in practice. The European Union use mechanisms and procedures for the introduction of new food additives into internal markets as well as controlling the circulation of additives. The Polish legislation in practice, however, does not determine approval or methods for the introduction of new food additives to the market. Legal regulations on the monitoring of food additives no exist.

  8. A mechanistic understanding of processing additive-induced efficiency enhancement in bulk heterojunction organic solar cells

    KAUST Repository

    Schmidt, Kristin

    2013-10-31

    The addition of processing additives is a widely used approach to increase power conversion efficiencies for many organic solar cells. We present how additives change the polymer conformation in the casting solution leading to a more intermixed phase-segregated network structure of the active layer which in turn results in a 5-fold enhancement in efficiency. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  9. Innovative Additive for Bitumen Based on Processed Fats

    Science.gov (United States)

    Babiak, Michał; Kosno, Jacek; Ratajczak, Maria; Zieliński, Krzysztof

    2017-10-01

    Various additives, admixtures and modifiers are used to improve technical properties and strength characteristics of building materials. Manufacturers of waterproofing materials, concrete, ceramics and bitumen have to use innovative, increasingly complex and costly additives, admixtures or modifiers. As a result, simple and inexpensive substances have been replaced by complex, long chain polymers, multi component resins or plastics. For economic and ecological reasons waste materials are more frequently used as additives, admixtures and modifiers. Nowadays the most commonly used physical modifiers of bitumen belong to the group of polymers - large molecular organic compounds of natural origin or being the result of planned chemical synthesis. Polymers are substances that do not chemically react with bitumen, they act as fillers or create a spatial network within bitumen (the so called physical cross-linking). The development of organic chemistry has allowed the synthesis of a number of substances chemically modifying bitumen. The most promising are heterocyclic organic compounds belonging to the group of imidazolines. The aim of the study presented in this paper was to demonstrate the suitability of processed natural and post-refining fat waste (diamidoamine dehydrate) as bitumen modifier. This paper discusses the impact of adding technical imidazoline on selected bitumen characteristics. Samples of bitumen 160/220, which is most commonly used for the production of waterproofing products, were analysed. For base bitumen and bitumen modified with technical imidazoline the following measurements were taken: measurement of the softening point by Ball and Ring method, determination of the breaking point by Fraass method and needle penetration measurement at 25°C. Later the samples were aged using TFOT laboratory method and the basic characteristics were determined again. The results showed that a small amount of imidazoline improved bitumen thermoplastic parameters at

  10. Self-organization processes in polysiloxane block copolymers, initiated by modifying fullerene additives

    Science.gov (United States)

    Voznyakovskii, A. P.; Kudoyarova, V. Kh.; Kudoyarov, M. F.; Patrova, M. Ya.

    2017-08-01

    Thin films of a polyblock polysiloxane copolymer and their composites with a modifying fullerene C60 additive are studied by atomic force microscopy, Rutherford backscattering, and neutron scattering. The data of atomic force microscopy show that with the addition of fullerene to the bulk of the polymer matrix, the initial relief of the film surface is leveled more, the larger the additive. This trend is associated with the processes of self-organization of rigid block sequences, which are initiated by the field effect of the surface of fullerene aggregates and lead to an increase in the number of their domains in the bulk of the polymer matrix. The data of Rutherford backscattering and neutron scattering indicate the formation of additional structures with a radius of 60 nm only in films containing fullerene, and their fraction increases with increasing fullerene concentration. A comparative analysis of the data of these methods has shown that such structures are, namely, the domains of a rigid block and are not formed by individual fullerene aggregates. The interrelation of the structure and mechanical properties of polymer films is considered.

  11. Hybrid Search for Faster Production and Safer Process Conditions in Friction Stir Welding

    DEFF Research Database (Denmark)

    Tutum, Cem Celal; Deb, Kalyanmoy; Hattel, Jesper Henri

    2011-01-01

    The objective of this paper is to investigate optimum process parameters and tool geometries in Friction Stir Welding (FSW) to minimize temperature difference between the leading edge of the tool probe and the work piece material in front of the tool shoulder, and simultaneously maximize traverse...... welding speed, which conflicts with the former objective. An evolutionary multi-objective optimization algorithm (i.e. NSGA-II), is applied to find multiple trade-off solutions followed by a gradient-based local search (i.e. SQP) to improve the convergence of the obtained Pareto-optimal front. In order...... choices have been offered based on several process specific performance and cost related criteria....

  12. Investigation of non-volatile additives on the process of distillation of hydrocarbon mixtures

    Directory of Open Access Journals (Sweden)

    М.Б. Степанов

    2009-02-01

    Full Text Available  The given results of researches of influence of nonvolatile additives on processes of distillation of individual hydrocarbons and their mixes, including petroleum and mineral oil. With the help of the developed computer system of the continuous control of distillation it is shown, that at the presence of small amounts of the additive decrease of temperature of the beginning of boiling of hydrocarbons is observed, their speeds of banish and exits of light fuel mineral oil grow during initial oil refining

  13. Characterization of Ti and Co based biomaterials processed via laser based additive manufacturing

    Science.gov (United States)

    Sahasrabudhe, Himanshu

    Titanium and Cobalt based metallic materials are currently the most ideal materials for load-bearing metallic bio medical applications. However, the long term tribological degradation of these materials still remains a problem that needs a solution. To improve the tribological performance of these two metallic systems, three different research approaches were adapted, stemming out four different research projects. First, the simplicity of laser gas nitriding was utilized with a modern LENS(TM) technology to form an in situ nitride rich later in titanium substrate material. This nitride rich composite coating improved the hardness by as much as fifteen times and reduced the wear rate by more than a magnitude. The leaching of metallic ions during wear was also reduced by four times. In the second research project, a mixture of titanium and silicon were processed on a titanium substrate in a nitrogen rich environment. The results of this reactive, in situ additive manufacturing process were Ti-Si-Nitride coatings that were harder than the titanium substrate by more than twenty times. These coatings also reduced the wear rate by more than two magnitudes. In the third research approach, composites of CoCrMo alloy and Calcium phosphate (CaP) bio ceramic were processed using LENS(TM) based additive manufacturing. These composites were effective in reducing the wear in the CoCrMo alloy by more than three times as well as reduce the leaching of cobalt and chromium ions during wear. The novel composite materials were found to develop a tribofilm during wear. In the final project, a combination of hard nitride coating and addition of CaP bioceramic was investigated by processing a mixture of Ti6Al4V alloy and CaP in a nitrogen rich environment using the LENS(TM) technology. The resultant Ti64-CaP-Nitride coatings significantly reduced the wear damage on the substrate. There was also a drastic reduction in the metal ions leached during wear. The results indicate that the three

  14. Bomb reduction of uranium tetrafluoride. Part II: Influence of the addition elements in the reduction process

    International Nuclear Information System (INIS)

    Anca Abati, R.; Lopez Rodriguez, M.

    1962-01-01

    This work shows the influence of uranium oxide and uranyl fluoride in the reduction of uranium with Ca and Mg. These additions are more harmful when using smaller bombs. The uranyl fluoride has influence in the reduction process; the curves yield-concentration shows two regions depending upon the salt concentration. The behaviour of this addition in these regions can be explained following the different decompositions that can take place during the reduction process. (Author) 9 refs

  15. Bromate Formation Characteristics of UV Irradiation, Hydrogen Peroxide Addition, Ozonation, and Their Combination Processes

    Directory of Open Access Journals (Sweden)

    Naoyuki Kishimoto

    2012-01-01

    Full Text Available Bromate formation characteristics of six-physicochemical oxidation processes, UV irradiation, single addition of hydrogen peroxide, ozonation, UV irradiation with hydrogen peroxide addition (UV/H2O2, ozonation with hydrogen peroxide addition (O3/H2O2, and ozonation with UV irradiation (O3/UV were investigated using 1.88 μM of potassium bromide solution with or without 6.4 μM of 4-chlorobenzoic acid. Bromate was not detected during UV irradiation, single addition of H2O2, and UV/H2O2, whereas ozone-based treatments produced . Hydroxyl radicals played more important role in bromate formation than molecular ozone. Acidification and addition of radical scavengers such as 4-chlorobenzoic acid were effective in inhibiting bromate formation during the ozone-based treatments because of inhibition of hydroxyl radical generation and consumption of hydroxyl radicals, respectively. The H2O2 addition was unable to decompose 4-chlorobenzoic acid, though O3/UV and O3/H2O2 showed the rapid degradation, and UV irradiation and UV/H2O2 showed the slow degradation. Consequently, if the concentration of organic contaminants is low, the UV irradiation and/or UV/H2O2 are applicable to organic contaminants removal without bromate formation. However, if the concentration of organic contaminants is high, O3/H2O2 and O3/UV should be discussed as advanced oxidation processes because of their high organic removal efficiency and low bromate formation potential at the optimum condition.

  16. Facile consecutive solvothermal growth of highly fluorescent InP/ZnS core/shell quantum dots using a safer phosphorus source.

    Science.gov (United States)

    Byun, Ho-June; Song, Woo-Seuk; Yang, Heesun

    2011-06-10

    The work presents a facile, stepwise synthetic approach for the production of highly fluorescent InP/ZnS core/shell quantum dots (QDs) by using a safer phosphorus (P) precursor. First, InP quantum dots (QDs) were solvothermally prepared at 180 °C for 24 h by using a P source of P(N(CH(3))(2))(3). The as-grown InP QDs were consecutively placed in another solvothermal condition for ZnS shell overcoating. In contrast to the almost non-fluorescent InP QDs, due to their highly defective surface states, the ZnS-coated InP QDs were highly fluorescent as a result of effective surface passivation. After the shell growth, the resulting InP/ZnS core/shell QDs were subjected to a size-sorting processing, by which red- to green-emitting QDs with quantum yields (QYs) of 24-60% were produced. Solvothermal shell growth parameters such as the reaction time and Zn/In solution concentration ratio were varied and optimized toward the highest QYs of core/shell QDs.

  17. Facile consecutive solvothermal growth of highly fluorescent InP/ZnS core/shell quantum dots using a safer phosphorus source

    International Nuclear Information System (INIS)

    Byun, Ho-June; Song, Woo-Seuk; Yang, Heesun

    2011-01-01

    The work presents a facile, stepwise synthetic approach for the production of highly fluorescent InP/ZnS core/shell quantum dots (QDs) by using a safer phosphorus (P) precursor. First, InP quantum dots (QDs) were solvothermally prepared at 180 deg. C for 24 h by using a P source of P(N(CH 3 ) 2 ) 3 . The as-grown InP QDs were consecutively placed in another solvothermal condition for ZnS shell overcoating. In contrast to the almost non-fluorescent InP QDs, due to their highly defective surface states, the ZnS-coated InP QDs were highly fluorescent as a result of effective surface passivation. After the shell growth, the resulting InP/ZnS core/shell QDs were subjected to a size-sorting processing, by which red- to green-emitting QDs with quantum yields (QYs) of 24-60% were produced. Solvothermal shell growth parameters such as the reaction time and Zn/In solution concentration ratio were varied and optimized toward the highest QYs of core/shell QDs.

  18. Facile consecutive solvothermal growth of highly fluorescent InP/ZnS core/shell quantum dots using a safer phosphorus source

    Science.gov (United States)

    Byun, Ho-June; Song, Woo-Seuk; Yang, Heesun

    2011-06-01

    The work presents a facile, stepwise synthetic approach for the production of highly fluorescent InP/ZnS core/shell quantum dots (QDs) by using a safer phosphorus (P) precursor. First, InP quantum dots (QDs) were solvothermally prepared at 180 °C for 24 h by using a P source of P(N(CH3)2)3. The as-grown InP QDs were consecutively placed in another solvothermal condition for ZnS shell overcoating. In contrast to the almost non-fluorescent InP QDs, due to their highly defective surface states, the ZnS-coated InP QDs were highly fluorescent as a result of effective surface passivation. After the shell growth, the resulting InP/ZnS core/shell QDs were subjected to a size-sorting processing, by which red- to green-emitting QDs with quantum yields (QYs) of 24-60% were produced. Solvothermal shell growth parameters such as the reaction time and Zn/In solution concentration ratio were varied and optimized toward the highest QYs of core/shell QDs.

  19. Facile consecutive solvothermal growth of highly fluorescent InP/ZnS core/shell quantum dots using a safer phosphorus source

    Energy Technology Data Exchange (ETDEWEB)

    Byun, Ho-June; Song, Woo-Seuk; Yang, Heesun, E-mail: hyang@hongik.ac.kr [Department of Materials Science and Engineering, Hongik University, Seoul 121-791 (Korea, Republic of)

    2011-06-10

    The work presents a facile, stepwise synthetic approach for the production of highly fluorescent InP/ZnS core/shell quantum dots (QDs) by using a safer phosphorus (P) precursor. First, InP quantum dots (QDs) were solvothermally prepared at 180 deg. C for 24 h by using a P source of P(N(CH{sub 3}){sub 2}){sub 3}. The as-grown InP QDs were consecutively placed in another solvothermal condition for ZnS shell overcoating. In contrast to the almost non-fluorescent InP QDs, due to their highly defective surface states, the ZnS-coated InP QDs were highly fluorescent as a result of effective surface passivation. After the shell growth, the resulting InP/ZnS core/shell QDs were subjected to a size-sorting processing, by which red- to green-emitting QDs with quantum yields (QYs) of 24-60% were produced. Solvothermal shell growth parameters such as the reaction time and Zn/In solution concentration ratio were varied and optimized toward the highest QYs of core/shell QDs.

  20. Performance evaluation and characterisation of EIGA produced titanium alloy powder for additive manufacturing processes

    CSIR Research Space (South Africa)

    Arthur, Nana KK

    2017-11-01

    Full Text Available affect powder quality, and hinder processing. In an investigation by Goso and Kale [3], Ti-6Al-4V alloy powder was produced by the hydride-dehydride (HDH) process in order to make titanium components by blended elemental approach. Chemical analysis.... 2016. Additive manufacturing of metals, Acta Materialia, 117, pp 371-392. 3 [3] Goso, X. and Kale, A. 2010. Production of titanium metal powder by the HDH process, (Paper presented at the South African Institute of Mining and Metallurgy Light...

  1. Rechargeable nickel-3D zinc batteries: An energy-dense, safer alternative to lithium-ion.

    Science.gov (United States)

    Parker, Joseph F; Chervin, Christopher N; Pala, Irina R; Machler, Meinrad; Burz, Michael F; Long, Jeffrey W; Rolison, Debra R

    2017-04-28

    The next generation of high-performance batteries should include alternative chemistries that are inherently safer to operate than nonaqueous lithium-based batteries. Aqueous zinc-based batteries can answer that challenge because monolithic zinc sponge anodes can be cycled in nickel-zinc alkaline cells hundreds to thousands of times without undergoing passivation or macroscale dendrite formation. We demonstrate that the three-dimensional (3D) zinc form-factor elevates the performance of nickel-zinc alkaline cells in three fields of use: (i) >90% theoretical depth of discharge (DOD Zn ) in primary (single-use) cells, (ii) >100 high-rate cycles at 40% DOD Zn at lithium-ion-commensurate specific energy, and (iii) the tens of thousands of power-demanding duty cycles required for start-stop microhybrid vehicles. Copyright © 2017, American Association for the Advancement of Science.

  2. Women's household decision-making autonomy and safer sex negotiation in Nigeria: An analysis of the Nigeria Demographic and Health Survey.

    Science.gov (United States)

    Sano, Yujiro; Sedziafa, Alice P; Vercillo, Siera; Antabe, Roger; Luginaah, Isaac

    2018-02-01

    Although married women's safer sex negotiation with their husbands is critical in reducing new HIV infections in Nigeria, its linkage to women's household decision-making autonomy is less explored in Nigeria. Drawing data from the 2013 Nigeria Demographic and Health Survey and using the logistic regression technique, we examined the associations between women's household decision-making autonomy and two indicators of the ability to engage in safer sex including whether married women 1) can refuse sex and 2) ask for condom use during sexual intercourse with husbands. Findings indicate that 64% and 41% of married women can refuse sex and ask for condom use, respectively. While the impact of women's household decision-making autonomy on the ability to refuse sex remained statistically significant after controlling for theoretically relevant variables (OR = 1.15; p < 0.001), its impact on the ability to ask for condom use became weakly significant once socioeconomic variables were controlled (OR = 1.03; p < 0.1). Based on these results, we have two suggestions. First, it may be important that marital-based policies and counselling promote environments in which married women can establish equal power relations with their husbands. Second, it is also important to eliminate structural barriers that hinder married women's economic opportunities in Nigeria.

  3. Right there all along. Latest IOM report lays out how to deliver safer, more effective care by using existing strategies, technology.

    Science.gov (United States)

    McKinney, Maureen

    2012-09-10

    Want to make healthcare safer and more cost-effective? You already have the necessary tools, a new IOM report says. "To Err is Human made visible the tremendous problem we had with medical errors, but back then very few systems had this kind of data infrastructure," says Paul Tang, of the Palo Alto (Calif.) Medical Foundation. said. "We're in a much different spot now."

  4. High performance poly(etherketoneketone) (PEKK) composite parts fabricated using Big Area Additive Manufacturing (BAAM) processes

    Energy Technology Data Exchange (ETDEWEB)

    Kunc, Vlastimil [ORNL; Kishore, Vidya [ORNL; Chen, Xun [ORNL; Ajinjeru, Christine [ORNL; Duty, Chad [University of Tennessee (UTK) and Oak Ridge National Laboratory (ORNL); Hassen, Ahmed A [ORNL

    2016-09-01

    ORNL collaborated with Arkema Inc. to investigate poly(etherketoneketone) (PEKK) and its composites as potential feedstock material for Big Area Additive Manufacturing (BAAM) system. In this work thermal and rheological properties were investigated and characterized in order to identify suitable processing conditions and material flow behavior for BAAM process.

  5. Structural integrity of additive materials: Microstructure, fatigue behavior, and surface processing

    Science.gov (United States)

    Book, Todd A.

    Although Additive Manufacturing (AM) offers numerous performance advantages over existing methods, AM structures are not being utilized for critical aerospace and mechanical applications due to uncertainties in their structural integrity as a result of the microstructural variations and defects arising from the AM process itself. Two of these uncertainties are the observed scatter in tensile strength and fatigue lives of direct metal laser sintering (DMLS) parts. With strain localization a precursor for material failure, this research seeks to explore the impact of microstructural variations in DMLS produced materials on strain localization. The first part of this research explores the role of the microstructure in strain localization of DMLS produced IN718 and Ti6Al4V specimens (as-built and post-processed) through the characterization of the linkage between microstructural variations, and the accumulation of plastic strain during monotonic and low cycle fatigue loading. The second part of this research explores the feasibility for the application of select surface processing techniques in-situ during the DMLS build process to alter the microstructure in AlSi10Mg to reduce strain localization and improve material cohesion. This study is based on utilizing experimental observations through the employment of advanced material characterization techniques such as digital image correlation to illustrate the impacts of DMLS microstructural variation.

  6. Liposuction-assisted four pedicle-based breast reduction (LAFPBR): A new safer technique of breast reduction for elderly patients.

    Science.gov (United States)

    La Padula, Simone; Hersant, Barbara; Noel, Warren; Meningaud, Jean Paul

    2018-05-01

    As older people increasingly care for their body image and remain active longer, the demand for reduction mammaplasty is increasing in this population. Only a few studies of reduction mammaplasty have specifically focussed on the outcomes in elderly women. We developed a new breast reduction technique: the Liposuction-Assisted Four Pedicle-Based Breast Reduction (LAFPBR) that is especially indicated for elderly patients. The aim of this paper was to describe the LAFPBR technique and to determine whether it could be considered a safer option for elderly patients compared to the superomedial pedicle (SMP) technique. A retrospective study included sixty-two women aged 60 years and over who underwent bilateral breast reduction mammaplasty. Thirty-one patients underwent LAFPBR and 31 patients were operated using the SMP technique. Complications and patient satisfaction in both groups were analysed. Patient satisfaction was measured using a validated questionnaire: the client satisfaction questionnaire 8 (CSQ-8). The LAFPBR technique required less operating time, and avoided significant blood loss. Six minor complications were observed in SMP patients. No LAFPBR women developed a procedure-related complication. Patient satisfaction was high with a mean score of 29.65 in LAFPBR patients and 28.68 in SMP patients. The LAFPBR is an easy procedure that appears safer than SMP and results in a high satisfaction rate in elderly women. Copyright © 2018 British Association of Plastic, Reconstructive and Aesthetic Surgeons. Published by Elsevier Ltd. All rights reserved.

  7. Modular Elastomer Photoresins for Digital Light Processing Additive Manufacturing.

    Science.gov (United States)

    Thrasher, Carl J; Schwartz, Johanna J; Boydston, Andrew J

    2017-11-15

    A series of photoresins suitable for the production of elastomeric objects via digital light processing additive manufacturing are reported. Notably, the printing procedure is readily accessible using only entry-level equipment under ambient conditions using visible light projection. The photoresin formulations were found to be modular in nature, and straightforward adjustments to the resin components enabled access to a range of compositions and mechanical properties. Collectively, the series includes silicones, hydrogels, and hybrids thereof. Printed test specimens displayed maximum elongations of up to 472% under tensile load, a tunable swelling behavior in water, and Shore A hardness values from 13.7 to 33.3. A combination of the resins was used to print a functional multimaterial three-armed pneumatic gripper. These photoresins could be transformative to advanced prototyping applications such as simulated human tissues, stimuli-responsive materials, wearable devices, and soft robotics.

  8. 41 CFR 102-38.225 - What are the additional requirements in the bid process?

    Science.gov (United States)

    2010-07-01

    ... OF PERSONAL PROPERTY Bids Acceptance of Bids § 102-38.225 What are the additional requirements in the bid process? All sales except fixed price sales must contain a certification of independent price...

  9. Evaluating Safer Conception Options for HIV-Serodiscordant Couples (HIV-Infected Female/HIV-Uninfected Male: A Closer Look at Vaginal Insemination

    Directory of Open Access Journals (Sweden)

    Okeoma Mmeje

    2012-01-01

    Full Text Available HIV serodiscordant couples represent at least half of all HIV-affected couples worldwide. Many of these couples have childbearing desires. Safer methods of conception may allow for pregnancy while minimizing the risk of sexual transmission of HIV. In serodiscordant partnerships with an HIV-infected female and HIV-uninfected male, vaginal insemination of a partner's semen during the fertile period coupled with 100% condom use may be the safest method of conception.

  10. Proceedings of the 4th Conference on Aerospace Materials, Processes, and Environmental Technology

    Science.gov (United States)

    Griffin, D. E. (Editor); Stanley, D. C. (Editor)

    2001-01-01

    The next millennium challenges us to produce innovative materials, processes, manufacturing, and environmental technologies that meet low-cost aerospace transportation needs while maintaining US leadership. The pursuit of advanced aerospace materials, manufacturing processes, and environmental technologies supports the development of safer, operational, next-generation, reusable, and expendable aeronautical and space vehicle systems. The Aerospace Materials, Processes, and Environmental Technology Conference (AMPET) provided a forum for manufacturing, environmental, materials, and processes engineers, scientists, and managers to describe, review, and critically assess advances in these key technology areas.

  11. Reduction of Surface Roughness by Means of Laser Processing over Additive Manufacturing Metal Parts.

    Science.gov (United States)

    Alfieri, Vittorio; Argenio, Paolo; Caiazzo, Fabrizia; Sergi, Vincenzo

    2016-12-31

    Optimization of processing parameters and exposure strategies is usually performed in additive manufacturing to set up the process; nevertheless, standards for roughness may not be evenly matched on a single complex part, since surface features depend on the building direction of the part. This paper aims to evaluate post processing treating via laser surface modification by means of scanning optics and beam wobbling to process metal parts resulting from selective laser melting of stainless steel in order to improve surface topography. The results are discussed in terms of roughness, geometry of the fusion zone in the cross-section, microstructural modification, and microhardness so as to assess the effects of laser post processing. The benefits of beam wobbling over linear scanning processing are shown, as heat effects in the base metal are proven to be lower.

  12. Selected Issues of the Indicating Measurements in a Spark Ignition Engine with an Additional Expansion Process

    Directory of Open Access Journals (Sweden)

    Marcin Noga

    2017-03-01

    Full Text Available The paper presents the results of research on the turbocharged spark ignition engine with additional exhaust expansion in a separate cylinder, which is commonly known as the five-stroke engine. The research engine has been constructed based on the four cylinder engine in which two outer cylinders work as the fired cylinders, while two internally connected inner cylinders constitute the volume of the additional expansion process. The engine represents a powertrain realizing an ultra-expansion cycle. The purpose of the study was to find an effective additional expansion process in the five-stroke engine. Cylinder-pressure indicating measurements were carried out for one of the fired cylinders and the additional expansion cylinder. The study was performed for over 20 different points on the engine operation map. This allowed us to determine a dependence between the pressure indicated in the fired cylinders and in the additional expansion cylinders. A function of the mean pressure indicated in the additional expansion cylinder versus a brake mean effective pressure was also presented. This showed a load threshold from which the work of the cylinders of additional expansion produced benefits for the output of the experimental engine. The issues of mechanical efficiency and effective efficiency of this engine were also discussed.

  13. Fabrication of Copper-Rich Cu-Al Alloy Using the Wire-Arc Additive Manufacturing Process

    Science.gov (United States)

    Dong, Bosheng; Pan, Zengxi; Shen, Chen; Ma, Yan; Li, Huijun

    2017-12-01

    An innovative wire-arc additive manufacturing (WAAM) process is used to fabricate Cu-9 at. pct Al on pure copper plates in situ, through separate feeding of pure Cu and Al wires into a molten pool, which is generated by the gas tungsten arc welding (GTAW) process. After overcoming several processing problems, such as opening the deposition molten pool on the extremely high-thermal conductive copper plate and conducting the Al wire into the molten pool with low feed speed, the copper-rich Cu-Al alloy was successfully produced with constant predesigned Al content above the dilution-affected area. Also, in order to homogenize the as-fabricated material and improve the mechanical properties, two further homogenization heat treatments at 1073 K (800 °C) and 1173 K (900 °C) were applied. The material and mechanical properties of as-fabricated and heat-treated samples were compared and analyzed in detail. With increased annealing temperatures, the content of precipitate phases decreased and the samples showed gradual improvements in both strength and ductility with little variation in microstructures. The present research opened a gate for in-situ fabrication of Cu-Al alloy with target chemical composition and full density using the additive manufacturing process.

  14. Automated road segment creation process : a report on research sponsored by SaferSim.

    Science.gov (United States)

    2016-08-01

    This report provides a summary of a set of tools that can be used to automate the process : of generating roadway surfaces from alignment and texture information. The tools developed : were created in Python 3.x and rely on the availability of two da...

  15. Processes that influence noncondom use behaviour of adolescents ...

    African Journals Online (AJOL)

    Results: Characteristics of condom use behaviour in five types emerged. The types were: i) Strong intention to have safer sex - due to parents, fear, future plans or self-respect; ii) Strong intention to have safer sex - learning through experience and bad examples; iii) Unsafe sex - impact of male dominance and sexual power; ...

  16. What Goes Around: the process of building a community-based harm reduction research project.

    Science.gov (United States)

    Jalloh, Chelsea; Illsley, Shohan; Wylie, John; Migliardi, Paula; West, Ethan; Stewart, Debbie; Mignone, Javier

    2017-11-16

    Often, research takes place on underserved populations rather than with underserved populations. This approach can further isolate and stigmatize groups that are already made marginalized. What Goes Around is a community-based research project that was led by community members themselves (Peers). This research aimed to implement a community-based research methodology grounded in the leadership and growing research capacity of community researchers and to investigate a topic which community members identified as important and meaningful. Chosen by community members, this project explored how safer sex and safer drug use information is shared informally among Peers. Seventeen community members actively engaged as both community researchers and research participants throughout all facets of the project: inception, implementation, analysis, and dissemination of results. Effective collaboration between community researchers, a community organization, and academics facilitated a research process in which community members actively guided the project from beginning to end. The methods used in What Goes Around demonstrated that it is not only possible, but advantageous, to draw from community members' involvement and direction in all stages of a community-based research project. This is particularly important when working with a historically underserved population. Purposeful and regular communication among collaborators, ongoing capacity building, and a commitment to respect the experience and expertise of community members were essential to the project's success. This project demonstrated that community members are highly invested in both informally sharing information about safer sex and safer drug use and taking leadership roles in directing research that prioritizes harm reduction in their communities.

  17. Results from the fielding of the Bio-surveillance Analysis, Feedback, Evaluation and Response (B-SAFER) system in Albuquerque, New Mexico.

    Science.gov (United States)

    Forslund, David; Umland, Edith; Brillman, Judith C; Joyce, Ed; Froman, Philip; Burr, Tom; Judd, Stephen L; Picard, Richard; Wokoun, Doug; Joner, Mike; Sewell, C Mack

    2003-01-01

    Public health authorities need a surveillance system that is sensitive enough to detect a disease outbreak early to enable a proper response. In order to meet this challenge we have deployed a pilot component-based system in Albuquerque, NM as part of the National Biodefense Initiative (BDI). B-SAFER gathers routinely collected data from healthcare institutions to monitor disease events in the community. We describe initial results from the deployment of the system for the past 6 months

  18. Evaluation of alternative chemical additives for high-level waste vitrification feed preparation processing

    International Nuclear Information System (INIS)

    Seymour, R.G.

    1995-01-01

    During the development of the feed processing flowsheet for the Defense Waste Processing Facility (DWPF) at the Savannah River Site (SRS), research had shown that use of formic acid (HCOOH) could accomplish several processing objectives with one chemical addition. These objectives included the decomposition of tetraphenylborate, chemical reduction of mercury, production of acceptable rheological properties in the feed slurry, and controlling the oxidation state of the glass melt pool. However, the DEPF research had not shown that some vitrification slurry feeds had a tendency to evolve hydrogen (H 2 ) and ammonia (NH 3 ) as the result of catalytic decomposition of CHOOH with noble metals (rhodium, ruthenium, palladium) in the feed. Testing conducted at Pacific Northwest Laboratory and later at the Savannah River Technical Center showed that the H 2 and NH 3 could evolve at appreciable rates and quantities. The explosive nature of H 2 and NH 3 (as ammonium nitrate) warranted significant mitigation control and redesign of both facilities. At the time the explosive gas evolution was discovered, the DWPF was already under construction and an immediate hardware fix in tandem with flowsheet changes was necessary. However, the Hanford Waste Vitrification Plant (HWVP) was in the design phase and could afford to take time to investigate flowsheet manipulations that could solve the problem, rather than a hardware fix. Thus, the HWVP began to investigate alternatives to using HCOOH in the vitrification process. This document describes the selection, evaluation criteria, and strategy used to evaluate the performance of the alternative chemical additives to CHOOH. The status of the evaluation is also discussed

  19. Additive Manufacturing Technologies Used for Processing Polymers: Current Status and Potential Application in Prosthetic Dentistry.

    Science.gov (United States)

    Revilla-León, Marta; Özcan, Mutlu

    2018-04-22

    There are 7 categories of additive manufacturing (AM) technologies, and a wide variety of materials can be used to build a CAD 3D object. The present article reviews the main AM processes for polymers for dental applications: stereolithography (SLA), digital light processing (DLP), material jetting (MJ), and material extrusion (ME). The manufacturing process, accuracy, and precision of these methods will be reviewed, as well as their prosthodontic applications. © 2018 by the American College of Prosthodontists.

  20. In flight image processing on multi-rotor aircraft for autonomous landing

    Science.gov (United States)

    Henry, Richard, Jr.

    An estimated $6.4 billion was spent during the year 2013 on developing drone technology around the world and is expected to double in the next decade. However, drone applications typically require strong pilot skills, safety, responsibilities and adherence to regulations during flight. If the flight control process could be safer and more reliable in terms of landing, it would be possible to further develop a wider range of applications. The objective of this research effort is to describe the design and evaluation of a fully autonomous Unmanned Aerial system (UAS), specifically a four rotor aircraft, commonly known as quad copter for precise landing applications. The full landing autonomy is achieved by image processing capabilities during flight for target recognition by employing the open source library OpenCV. In addition, all imaging data is processed by a single embedded computer that estimates a relative position with respect to the target landing pad. Results shows a reduction on the average offset error by 67.88% in comparison to the current return to lunch (RTL) method which only relies on GPS positioning. The present work validates the need for relying on image processing for precise landing applications instead of the inexact method of a commercial low cost GPS dependency.

  1. A test for judging the presence of additional scatter in a Poisson process

    International Nuclear Information System (INIS)

    Mueller, J.W.

    1978-01-01

    The effect of additional scatter on a Poisson process is studied. Possible causes for such fluctuations are insufficient stability of the detection efficiency or of the associated electronics. It is shown with a simple model that the presence of fluctuations results in a characteristic broadening of the counting distribution. Comparison of the observed distribution with the one expected for a Poisson process with the same mean value will show three different regions, each with predictable sign of the deviation; the presence of scatter can thus be decided upon by a sign test. Experimental results are in excellent agreement with this expectation

  2. A study of internal structure in components made by additive manufacturing process using 3 D X-ray tomography

    Energy Technology Data Exchange (ETDEWEB)

    Raguvarun, K., E-mail: prajagopal@iitm.ac.in; Balasubramaniam, Krishnan, E-mail: prajagopal@iitm.ac.in; Rajagopal, Prabhu, E-mail: prajagopal@iitm.ac.in [Centre for NDE, Indian Institute of Technology Madras, Chennai 600036, Tamilnadu (India); Palanisamy, Suresh [Swinburne University of Technology, Faculty of Engineering, Science and Technology, Hawthorn, Victoria 3122 Australia and Defence Materials Technology Centre, Hawthorn, Victoria 3122 (Australia); Nagarajah, Romesh; Kapoor, Ajay [Swinburne University of Technology, Faculty of Engineering, Science and Technology, Hawthorn, Victoria 3122 (Australia); Hoye, Nicholas; Curiri, Dominic [University of Wollongong, Faculty of Engineering, New South Wales 2522, Australia and Defence Materials Technology Centre, Hawthorn, Victoria 3122 (Australia)

    2015-03-31

    Additive manufacturing methods are gaining increasing popularity for rapidly and efficiently manufacturing parts and components in the industrial context, as well as for domestic applications. However, except when used for prototyping or rapid visualization of components, industries are concerned with the load carrying capacity and strength achievable by additive manufactured parts. In this paper, the wire-arc additive manufacturing (AM) process based on gas tungsten arc welding (GTAW) has been examined for the internal structure and constitution of components generated by the process. High-resolution 3D X-ray tomography is used to gain cut-views through wedge-shaped parts created using this GTAW additive manufacturing process with titanium alloy materials. In this work, two different control conditions for the GTAW process are considered. The studies reveal clusters of porosities, located in periodic spatial intervals along the sample cross-section. Such internal defects can have a detrimental effect on the strength of the resulting AM components, as shown in destructive testing studies. Closer examination of this phenomenon shows that defect clusters are preferentially located at GTAW traversal path intervals. These results highlight the strong need for enhanced control of process parameters in ensuring components with minimal defects and higher strength.

  3. A study of internal structure in components made by additive manufacturing process using 3 D X-ray tomography

    International Nuclear Information System (INIS)

    Raguvarun, K.; Balasubramaniam, Krishnan; Rajagopal, Prabhu; Palanisamy, Suresh; Nagarajah, Romesh; Kapoor, Ajay; Hoye, Nicholas; Curiri, Dominic

    2015-01-01

    Additive manufacturing methods are gaining increasing popularity for rapidly and efficiently manufacturing parts and components in the industrial context, as well as for domestic applications. However, except when used for prototyping or rapid visualization of components, industries are concerned with the load carrying capacity and strength achievable by additive manufactured parts. In this paper, the wire-arc additive manufacturing (AM) process based on gas tungsten arc welding (GTAW) has been examined for the internal structure and constitution of components generated by the process. High-resolution 3D X-ray tomography is used to gain cut-views through wedge-shaped parts created using this GTAW additive manufacturing process with titanium alloy materials. In this work, two different control conditions for the GTAW process are considered. The studies reveal clusters of porosities, located in periodic spatial intervals along the sample cross-section. Such internal defects can have a detrimental effect on the strength of the resulting AM components, as shown in destructive testing studies. Closer examination of this phenomenon shows that defect clusters are preferentially located at GTAW traversal path intervals. These results highlight the strong need for enhanced control of process parameters in ensuring components with minimal defects and higher strength

  4. Positive reinforcement to promote safer sex among clients.

    Science.gov (United States)

    Raman, S

    1992-01-01

    The AIDS Research Foundation of India (ARFI) began an intervention program with sex workers in Madras where the women reported that they were willing to use condoms, whereas the customers were not. Accordingly, ARFI is focusing on clients using a positive reinforcement approach: repetition of the desirability of condom use by communication. First, truck drivers and dock workers have been targeted. Drivers interviewed by ARFI were familiar with the condom as a contraceptive method rather than a disease-preventing method, and used it with their wives. The ARFI program has convinced tobacco shopkeepers to stock condoms for drivers. Truckers receive key chains with a holder for a condom. At transit site tea shops songs are aired about road and roadside safety sponsored by a tire manufacturer with a message about rubber (tires and condoms). Women selling sex at transit sites are also educated about the human immunodeficiency virus (HIV) infection and sexually transmitted diseases (STDs) while attempting to increase their level of hygiene. The typical Friday night sex-seeking behavior among dock workers consists of drinking in a wine shop and soliciting sex workers. Port management and unions have also been recruited for promoting AIDS-related education after participating in health education sessions with flip charts and flash cards. Rest rooms display posters on condom use, some men have been recruited as condom holders for distribution on Friday nights, and barber shops also feature posters with messages about safer sex. AIDS/STD prevention programs have to deal with prevailing practices, values, and beliefs. Results indicate increased condom use among clients as shown by increased sales at transit site tobacco shops and shops around the port. In the future the program will pay more attention to improving the negotiation skills of sex workers.

  5. Safe transition to surgery: working differently to make blood transfusion process safer for elective surgery.

    Science.gov (United States)

    Badjie, Karafa S W; Rogers, James C; Jenkins, Sarah M; Bundy, Kevin L; Stubbs, James R; Cima, Robert R

    2015-09-01

    Our institutional policy allows patients who are scheduled for elective surgery with no history of a pregnancy or blood transfusion in the preceding 3 months to have a presurgical sample (PSS) collected and tested up to 56 days before their scheduled surgery; however, our PSS TS completion rate in eligible patients before the morning of surgery was 83%. In 2011, a team was charged to develop a standardized process along with other process improvements while ensuring no increase in transfusion-related events. The team followed the DMAIC framework in appraising the effectiveness and efficiency of the current state process including baseline data collection such as PSS TS completion rate, number of eligible patients needing a PSS TS on the day of surgery, benchmarking, SSBO utilization, and future state mapping. First quarter (Q1) 2011 versus Q1 2012 postimplementation results showed significant improvements of the process including a 53% decrease in PSS TS on the day of surgery; a 13% increase in PSS TS completion before the morning of surgery; a 26% reduction in total XM RBCs; and a 58.8% reduction in XM RBCs not issued, plus a 47% decrease in RBC wastage. Q1 2011 versus Q1 2013 showed a 41% reduction in total XM RBCs and an 88.4% reduction in XM RBCs not issued but overall RBCs issued versus returned increased slightly and represents a future opportunity for improvement. The redesigned, transformational process eliminated SSBO and improved ordering process and PSS TS completion rate as well as blood product ordering and utilization. © 2015 AABB.

  6. Vaccine process technology.

    Science.gov (United States)

    Josefsberg, Jessica O; Buckland, Barry

    2012-06-01

    The evolution of vaccines (e.g., live attenuated, recombinant) and vaccine production methods (e.g., in ovo, cell culture) are intimately tied to each other. As vaccine technology has advanced, the methods to produce the vaccine have advanced and new vaccine opportunities have been created. These technologies will continue to evolve as we strive for safer and more immunogenic vaccines and as our understanding of biology improves. The evolution of vaccine process technology has occurred in parallel to the remarkable growth in the development of therapeutic proteins as products; therefore, recent vaccine innovations can leverage the progress made in the broader biotechnology industry. Numerous important legacy vaccines are still in use today despite their traditional manufacturing processes, with further development focusing on improving stability (e.g., novel excipients) and updating formulation (e.g., combination vaccines) and delivery methods (e.g., skin patches). Modern vaccine development is currently exploiting a wide array of novel technologies to create safer and more efficacious vaccines including: viral vectors produced in animal cells, virus-like particles produced in yeast or insect cells, polysaccharide conjugation to carrier proteins, DNA plasmids produced in E. coli, and therapeutic cancer vaccines created by in vitro activation of patient leukocytes. Purification advances (e.g., membrane adsorption, precipitation) are increasing efficiency, while innovative analytical methods (e.g., microsphere-based multiplex assays, RNA microarrays) are improving process understanding. Novel adjuvants such as monophosphoryl lipid A, which acts on antigen presenting cell toll-like receptors, are expanding the previously conservative list of widely accepted vaccine adjuvants. As in other areas of biotechnology, process characterization by sophisticated analysis is critical not only to improve yields, but also to determine the final product quality. From a regulatory

  7. Additive manufacturing of titanium alloys in the biomedical field: processes, properties and applications.

    Science.gov (United States)

    Trevisan, Francesco; Calignano, Flaviana; Aversa, Alberta; Marchese, Giulio; Lombardi, Mariangela; Biamino, Sara; Ugues, Daniele; Manfredi, Diego

    2018-04-01

    The mechanical properties and biocompatibility of titanium alloy medical devices and implants produced by additive manufacturing (AM) technologies - in particular, selective laser melting (SLM), electron beam melting (EBM) and laser metal deposition (LMD) - have been investigated by several researchers demonstrating how these innovative processes are able to fulfil medical requirements for clinical applications. This work reviews the advantages given by these technologies, which include the possibility to create porous complex structures to improve osseointegration and mechanical properties (best match with the modulus of elasticity of local bone), to lower processing costs, to produce custom-made implants according to the data for the patient acquired via computed tomography and to reduce waste.

  8. TU-FG-201-11: Evaluating the Validity of Prospective Risk Analysis Methods: A Comparison of Traditional FMEA and Modified Healthcare FMEA

    Energy Technology Data Exchange (ETDEWEB)

    Lah, J [Myongji Hospital, Goyang-si (Korea, Republic of); Manger, R; Kim, G [University of California, San Diego, La Jolla, CA (United States)

    2016-06-15

    Purpose: To examine the ability of traditional Failure mode and effects analysis (FMEA) and a light version of Healthcare FMEA (HFMEA), called Scenario analysis of FMEA (SAFER) by comparing their outputs in terms of the risks identified and their severity rankings. Methods: We applied two prospective methods of the quality management to surface image guided, linac-based radiosurgery (SIG-RS). For the traditional FMEA, decisions on how to improve an operation are based on risk priority number (RPN). RPN is a product of three indices: occurrence, severity and detectability. The SAFER approach; utilized two indices-frequency and severity-which were defined by a multidisciplinary team. A criticality matrix was divided into 4 categories; very low, low, high and very high. For high risk events, an additional evaluation was performed. Based upon the criticality of the process, it was decided if additional safety measures were needed and what they comprise. Results: Two methods were independently compared to determine if the results and rated risks were matching or not. Our results showed an agreement of 67% between FMEA and SAFER approaches for the 15 riskiest SIG-specific failure modes. The main differences between the two approaches were the distribution of the values and the failure modes (No.52, 54, 154) that have high SAFER scores do not necessarily have high FMEA RPN scores. In our results, there were additional risks identified by both methods with little correspondence. In the SAFER, when the risk score is determined, the basis of the established decision tree or the failure mode should be more investigated. Conclusion: The FMEA method takes into account the probability that an error passes without being detected. SAFER is inductive because it requires the identification of the consequences from causes, and semi-quantitative since it allow the prioritization of risks and mitigation measures, and thus is perfectly applicable to clinical parts of radiotherapy.

  9. TU-FG-201-11: Evaluating the Validity of Prospective Risk Analysis Methods: A Comparison of Traditional FMEA and Modified Healthcare FMEA

    International Nuclear Information System (INIS)

    Lah, J; Manger, R; Kim, G

    2016-01-01

    Purpose: To examine the ability of traditional Failure mode and effects analysis (FMEA) and a light version of Healthcare FMEA (HFMEA), called Scenario analysis of FMEA (SAFER) by comparing their outputs in terms of the risks identified and their severity rankings. Methods: We applied two prospective methods of the quality management to surface image guided, linac-based radiosurgery (SIG-RS). For the traditional FMEA, decisions on how to improve an operation are based on risk priority number (RPN). RPN is a product of three indices: occurrence, severity and detectability. The SAFER approach; utilized two indices-frequency and severity-which were defined by a multidisciplinary team. A criticality matrix was divided into 4 categories; very low, low, high and very high. For high risk events, an additional evaluation was performed. Based upon the criticality of the process, it was decided if additional safety measures were needed and what they comprise. Results: Two methods were independently compared to determine if the results and rated risks were matching or not. Our results showed an agreement of 67% between FMEA and SAFER approaches for the 15 riskiest SIG-specific failure modes. The main differences between the two approaches were the distribution of the values and the failure modes (No.52, 54, 154) that have high SAFER scores do not necessarily have high FMEA RPN scores. In our results, there were additional risks identified by both methods with little correspondence. In the SAFER, when the risk score is determined, the basis of the established decision tree or the failure mode should be more investigated. Conclusion: The FMEA method takes into account the probability that an error passes without being detected. SAFER is inductive because it requires the identification of the consequences from causes, and semi-quantitative since it allow the prioritization of risks and mitigation measures, and thus is perfectly applicable to clinical parts of radiotherapy.

  10. Effect of Steam Deactivation Severity of ZSM-5 Additives on LPG Olefins Production in the FCC Process.

    Science.gov (United States)

    Gusev, Andrey A; Psarras, Antonios C; Triantafyllidis, Konstantinos S; Lappas, Angelos A; Diddams, Paul A

    2017-10-21

    ZSM-5-containing catalytic additives are widely used in oil refineries to boost light olefin production and improve gasoline octanes in the Fluid Catalytic Cracking (FCC) process. Under the hydrothermal conditions present in the FCC regenerator (typically >700 °C and >8% steam), FCC catalysts and additives are subject to deactivation. Zeolites (e.g., Rare Earth USY in the base catalyst and ZSM-5 in Olefins boosting additives) are prone to dealumination and partial structural collapse, thereby losing activity, micropore surface area, and undergoing changes in selectivity. Fresh catalyst and additives are added at appropriate respective levels to the FCC unit on a daily basis to maintain overall targeted steady-state (equilibrated) activity and selectivity. To mimic this process under accelerated laboratory conditions, a commercial P/ZSM-5 additive was hydrothermally equilibrated via a steaming process at two temperatures: 788 °C and 815 °C to simulate moderate and more severe equilibration industrial conditions, respectively. n -Dodecane was used as probe molecule and feed for micro-activity cracking testing at 560 °C to determine the activity and product selectivity of fresh and equilibrated P-doped ZSM-5 additives. The fresh/calcined P/ZSM-5 additive was very active in C 12 cracking while steaming limited its activity, i.e., at catalyst-to-feed (C/F) ratio of 1, about 70% and 30% conversion was obtained with the fresh and steamed additives, respectively. A greater activity drop was observed upon increasing the hydrothermal deactivation severity due to gradual decrease of total acidity and microporosity of the additives. However, this change in severity did not result in any selectivity changes for the LPG (liquefied petroleum gas) olefins as the nature (Brønsted-to-Lewis ratio) of the acid/active sites was not significantly altered upon steaming. Steam deactivation of ZSM-5 had also no significant effect on aromatics formation which was enhanced at higher

  11. Effect of Steam Deactivation Severity of ZSM-5 Additives on LPG Olefins Production in the FCC Process

    Directory of Open Access Journals (Sweden)

    Andrey A. Gusev

    2017-10-01

    Full Text Available ZSM-5-containing catalytic additives are widely used in oil refineries to boost light olefin production and improve gasoline octanes in the Fluid Catalytic Cracking (FCC process. Under the hydrothermal conditions present in the FCC regenerator (typically >700 °C and >8% steam, FCC catalysts and additives are subject to deactivation. Zeolites (e.g., Rare Earth USY in the base catalyst and ZSM-5 in Olefins boosting additives are prone to dealumination and partial structural collapse, thereby losing activity, micropore surface area, and undergoing changes in selectivity. Fresh catalyst and additives are added at appropriate respective levels to the FCC unit on a daily basis to maintain overall targeted steady-state (equilibrated activity and selectivity. To mimic this process under accelerated laboratory conditions, a commercial P/ZSM-5 additive was hydrothermally equilibrated via a steaming process at two temperatures: 788 °C and 815 °C to simulate moderate and more severe equilibration industrial conditions, respectively. n-Dodecane was used as probe molecule and feed for micro-activity cracking testing at 560 °C to determine the activity and product selectivity of fresh and equilibrated P-doped ZSM-5 additives. The fresh/calcined P/ZSM-5 additive was very active in C12 cracking while steaming limited its activity, i.e., at catalyst-to-feed (C/F ratio of 1, about 70% and 30% conversion was obtained with the fresh and steamed additives, respectively. A greater activity drop was observed upon increasing the hydrothermal deactivation severity due to gradual decrease of total acidity and microporosity of the additives. However, this change in severity did not result in any selectivity changes for the LPG (liquefied petroleum gas olefins as the nature (Brønsted-to-Lewis ratio of the acid/active sites was not significantly altered upon steaming. Steam deactivation of ZSM-5 had also no significant effect on aromatics formation which was enhanced at

  12. The SAFER guides: empowering organizations to improve the safety and effectiveness of electronic health records.

    Science.gov (United States)

    Sittig, Dean F; Ash, Joan S; Singh, Hardeep

    2014-05-01

    Electronic health records (EHRs) have potential to improve quality and safety of healthcare. However, EHR users have experienced safety concerns from EHR design and usability features that are not optimally adapted for the complex work flow of real-world practice. Few strategies exist to address unintended consequences from implementation of EHRs and other health information technologies. We propose that organizations equipped with EHRs should consider the strategy of "proactive risk assessment" of their EHR-enabled healthcare system to identify and address EHR-related safety concerns. In this paper, we describe the conceptual underpinning of an EHR-related self-assessment strategy to provide institutions a foundation upon which they could build their safety efforts. With support from the Office of the National Coordinator for Health Information Technology (ONC), we used a rigorous, iterative process to develop a set of 9 self-assessment tools to optimize the safety and safe use of EHRs. These tools, referred to as the Safety Assurance Factors for EHR Resilience (SAFER) guides, could be used to self-assess safety and effectiveness of EHR implementations, identify specific areas of vulnerability, and create solutions and culture change to mitigate risks. A variety of audiences could conduct these assessments, including frontline clinicians or care teams in different practices, or clinical, quality, or administrative leaders within larger institutions. The guides use a multifaceted systems-based approach to assess risk and empower organizations to work with internal or external stakeholders (eg, EHR developers) on optimizing EHR functionality and using EHRs to drive improvements in the quality and safety of healthcare.

  13. Assessing the additional impact of Process Recovery Communications on Customer Outcomes: A Comprehensive Service Recovery Approach

    OpenAIRE

    Y. VAN VAERENBERGH; B. LARIVIÈRE; I. VERMEIR

    2009-01-01

    Purpose – Services recoveries following service failures not only imply customer recovery opportunities in which customer-company relationships can be restored, they can also result in process improvements (i.e. process recoveries in literature). This paper seeks to identify the additional impact of process recoveries on four customer outcome variables (satisfaction with service recovery, overall satisfaction, repurchase intent and word-of-mouth) by communicating these improvements back to th...

  14. Learning Additional Languages as Hierarchical Probabilistic Inference: Insights From First Language Processing.

    Science.gov (United States)

    Pajak, Bozena; Fine, Alex B; Kleinschmidt, Dave F; Jaeger, T Florian

    2016-12-01

    We present a framework of second and additional language (L2/L n ) acquisition motivated by recent work on socio-indexical knowledge in first language (L1) processing. The distribution of linguistic categories covaries with socio-indexical variables (e.g., talker identity, gender, dialects). We summarize evidence that implicit probabilistic knowledge of this covariance is critical to L1 processing, and propose that L2/L n learning uses the same type of socio-indexical information to probabilistically infer latent hierarchical structure over previously learned and new languages. This structure guides the acquisition of new languages based on their inferred place within that hierarchy, and is itself continuously revised based on new input from any language. This proposal unifies L1 processing and L2/L n acquisition as probabilistic inference under uncertainty over socio-indexical structure. It also offers a new perspective on crosslinguistic influences during L2/L n learning, accommodating gradient and continued transfer (both negative and positive) from previously learned to novel languages, and vice versa.

  15. Assessing the potential contributions of additional retention processes to PFAS retardation in the subsurface.

    Science.gov (United States)

    Brusseau, Mark L

    2018-02-01

    A comprehensive understanding of the transport and fate of per- and poly-fluoroalkyl substances (PFAS) in the subsurface is critical for accurate risk assessments and design of effective remedial actions. A multi-process retention model is proposed to account for potential additional sources of retardation for PFAS transport in source zones. These include partitioning to the soil atmosphere, adsorption at air-water interfaces, partitioning to trapped organic liquids (NAPL), and adsorption at NAPL-water interfaces. An initial assessment of the relative magnitudes and significance of these retention processes was conducted for two PFAS of primary concern, perfluorooctanesulfonic acid (PFOS) and perfluorooctanoic acid (PFOA), and an example precursor (fluorotelomer alcohol, FTOH). The illustrative evaluation was conducted using measured porous-medium properties representative of a sandy vadose-zone soil. Data collected from the literature were used to determine measured or estimated values for the relevant distribution coefficients, which were in turn used to calculate retardation factors for the model system. The results showed that adsorption at the air-water interface was a primary source of retention for both PFOA and PFOS, contributing approximately 50% of total retention for the conditions employed. Adsorption to NAPL-water interfaces and partitioning to bulk NAPL were also shown to be significant sources of retention. NAPL partitioning was the predominant source of retention for FTOH, contributing ~98% of total retention. These results indicate that these additional processes may be, in some cases, significant sources of retention for subsurface transport of PFAS. The specific magnitudes and significance of the individual retention processes will depend upon the properties and conditions of the specific system of interest (e.g., PFAS constituent and concentration, porous medium, aqueous chemistry, fluid saturations, co-contaminants). In cases wherein these

  16. Modification of the process dynamics in micro-EDM by means of an additional piezo-control system

    Science.gov (United States)

    Herzig, M.; Berger, T.; Schulze, H.-P.; Hackert-Oschätzchen, M.; Kröning, O.; Schubert, A.

    2017-10-01

    For the application of spark erosion in micro- and precision manufacturing, it is particularly important that small structures with small spark gaps can be machined in the range of a few micrometers. Due to the application of an additional high- dynamic piezo positioning system, smaller feed steps can be implemented which ensure a higher process stability. This additional feed system can be adapted to existing feed systems, whereby the process variable to be influenced is the spark gap. The primary feed system does not have to be directly influenced. The article shows how the structures of parallel regulation circuits for such operating piezo positioning systems are constructed and how they can improve the productivity, the machining accuracy and the surface quality. A selected example shows how the structural design of the highly dynamic system can be designed for different process parameters of industrial basic systems.

  17. Novel additives in radiation polymerisation processes. Significance of molecular weight data in their application to grafting, curing and composite formation

    International Nuclear Information System (INIS)

    Garnett, J.L.; Mohajerani, S.; Viengkhou, V.; Loo-Teck NG

    1995-01-01

    The role of additives in accelerating rates of reaction has been investigated in the following related radiation polymerisation processes, i.e simple homopolymerisation, grafting, WPC formation and curing. Additives used include mineral acid, polyfunctional monomers, urea and thermal and photochemical initiators. Molecular weight analysis carried out on the polymers formed in the presence of the additives indicate that both chemical and physical processes are involved in the mechanism of the polymerisation reaction. Chemical processes (free radicals) lead to an enhancement in initial rate of polymerisation whilst the physical parameter involves partitioning of reagents during reaction. Both chemical and physical processes are shown to act in concert to influence both polymer yield and properties

  18. Aluminium content of some processed foods, raw materials and food additives in China by inductively coupled plasma-mass spectrometry.

    Science.gov (United States)

    Deng, Gui-Fang; Li, Ke; Ma, Jing; Liu, Fen; Dai, Jing-Jing; Li, Hua-Bin

    2011-01-01

    The level of aluminium in 178 processed food samples from Shenzhen city in China was evaluated using inductively coupled plasma-mass spectrometry. Some processed foods contained a concentration of up to 1226 mg/kg, which is about 12 times the Chinese food standard. To establish the main source in these foods, Al levels in the raw materials were determined. However, aluminium concentrations in raw materials were low (0.10-451.5 mg/kg). Therefore, aluminium levels in food additives used in these foods was determined and it was found that some food additives contained a high concentration of aluminium (0.005-57.4 g/kg). The results suggested that, in the interest of public health, food additives containing high concentrations of aluminium should be replaced by those containing less. This study has provided new information on aluminium levels in Chinese processed foods, raw materials and a selection of food additives.

  19. Enzymatic Refining and Cellulose Nanofiber Addition in Papermaking Processes from Recycled and Deinked Slurries

    Directory of Open Access Journals (Sweden)

    Marc Delgado-Aguilar

    2015-07-01

    Full Text Available Recycling and deinking processes cause fiber damage because of hornification phenomena and increased external fibrillation. Mechanical refining has been used for many years to enhance the mechanical properties of paper. Biorefining of pulp using enzymes is receiving increasing interest for energy reduction at the refining step of the paper-making process. Moreover, enzymes have also been used for the enhancement of mechanical properties without affecting the drainage rate. As an alternative to mechanical refining treatment, a combination of an enzymatic treatment and cellulose nanofibril (CNF addition was explored to enhance the mechanical properties of paper. The tests were carried out on a deinked pulp (DIP suspension made of 50% old newspapers (ONP and 50% old magazines (OMG. Various enzyme charges and CNF amounts were added to the mixture of ONP and OMG. All pulps (treated and untreated were characterized from a morphological point of view, and the paper sheets made thereof were mechanically characterized. The combination of the enzymatic treatment with the addition of 3% CNF provided sufficient tensile strength for the paper to be used in high-performance applications.

  20. Characterization and Processing Behavior of Heated Aluminum-Polycarbonate Composite Build Plates for the FDM Additive Manufacturing Process

    Directory of Open Access Journals (Sweden)

    Sherri L. Messimer

    2018-02-01

    Full Text Available One of the most essential components of the fused deposition modeling (FDM additive manufacturing (AM process is the build plate, the surface upon which the part is constructed. These are typically made from aluminum or glass, but there are clear disadvantages to both and restrictions on which materials can be processed on them successfully. This study examined the suitability of heated aluminum-polycarbonate (AL-PC composite print beds for FDM, looking particularly at the mechanical properties, thermal behavior, deformation behavior, bonding strength with deposited material, printing quality, and range of material usability. Theoretical examination and physical experiments were performed for each of these areas; the results were compared to similar experiments done using heated aluminum and aluminum-glass print beds. Ten distinct materials (ABS, PLA, PET, HIPS, PC, TPU, PVA, nylon, metal PLA, and carbon-fiber PLA were tested for printing performance. The use of a heated AL-PC print bed was found to be a practical option for most of the materials, particularly ABS and TPU, which are often challenging to process using traditional print bed types. Generally, the results were found to be equivalent to or superior to tempered glass and superior to standard aluminum build plates in terms of printing capability.

  1. Measuring emotions in traffic : paper presented at the ESF Congress ‘Towards Safer Road Traffic in Southern Europe’, May 31st-June 2nd 2001, Ankara, Turkey.

    NARCIS (Netherlands)

    Mesken, J.

    2002-01-01

    This paper contains the text of a presentation held at the European Science Foundation Congress ‘Towards Safer Road Traffic in Southern Europe’ (May 31st – June 2nd, 2001, Ankara , Turkey). In this paper, methods to measure emotions are reviewed and possible applications for traffic research are

  2. INNOVATIVE TECHNOLOGY FOR THE PRODUCTION OF FOOD ADDITIVES FROM PUMPKIN PROCESSING SECONDARY RESOURCES

    OpenAIRE

    Kupin G. A.; Kornen N. N.; Matvienko A. N.; Shahray T. A.; Pershakova T. V.

    2016-01-01

    The article presents data characterizing the composition of macro and micronutrients from secondary resources of pumpkin processing – pumpkin pomace. We have found that extracts of pumpkin are valuable raw materials for the production of food additives, as they contain proteins, dietary fiber, including pectin and protopectin, minerals, as well as such biologically active substances as vitamin C, β- carotene and P-active substances using nuclear magnetic relaxation, it is shown that pretreatm...

  3. Integration of Fiber-Reinforced Polymers in a Life Cycle Assessment of Injection Molding Process Chains with Additive Manufacturing

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Bey, Niki; Mischkot, Michael

    2017-01-01

    Additive manufacturing technologies applied to injection molding process chain have acquired an increasingly important role in the context of tool inserts production, especially by vat polymerization. Despite the decreased lifetime during their use in the injection molding process, the inserts come...... with improvements in terms of production time, costs, exibility, as well as potentially improved environmental performance as compared to conventional materials in a life cycle perspective.This contribution supports the development of additively manufactured injection molding inserts with the use of fiber...

  4. Additive Manufacturing Infrared Inspection

    Science.gov (United States)

    Gaddy, Darrell; Nettles, Mindy

    2015-01-01

    The Additive Manufacturing Infrared Inspection Task started the development of a real-time dimensional inspection technique and digital quality record for the additive manufacturing process using infrared camera imaging and processing techniques. This project will benefit additive manufacturing by providing real-time inspection of internal geometry that is not currently possible and reduce the time and cost of additive manufactured parts with automated real-time dimensional inspections which deletes post-production inspections.

  5. Water productivity using SAFER - Simple Algorithm for Evapotranspiration Retrieving in watershed

    Directory of Open Access Journals (Sweden)

    Daniel N. Coaguila

    Full Text Available ABSTRACT The Cabeceira Comprida stream’s watershed, located in Santa Fé do Sul, São Paulo state, has great environmental importance. It is essential for supplying water to the population and generating surpluses for sewage dilution. This study aimed to evaluate the annual performance of the components of water productivity from Landsat-8 images of 2015, using the Simple Algorithm for Evapotranspiration Retrieving (SAFER, calculating the actual evapotranspiration (ETa, biomass (BIO and water productivity (WP. The annual averages of ETa, BIO and WP were 1.03 mm day-1, 36.04 kg ha-1 day-1 and 3.19 kg m-3, respectively. The average annual values of ETa for land use and occupation were 1.40, 1.23, 1.05, 0.97 and 1.08 mm day-1 for the remaining forest (RF, invasive species (IS, pasture (Pa, annual crop (AC and perennial crop (PC, respectively, with BIO of 57.64, 46.10, 36.78, 32.69, 40.03 kg ha-1 day-1 for RF, IS, Pa, AC and PC, respectively, resulting in WP of 3.94, 3.59, 3.25, 3.09, 3.35 kg m-3 for RF, IS, Pa, AC and PC, respectively. The ETa, BIO and WP adjust to the seasonality of the region, and RF and IS stood out with the highest values.

  6. Determination of Process Parameters for High-Density, Ti-6Al-4V Parts Using Additive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Kamath, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-08-10

    In our earlier work, we described an approach for determining the process parameters that re- sult in high-density parts manufactured using the additive-manufacturing process of selective laser melting (SLM). Our approach, which combines simple simulations and experiments, was demon- strated using 316L stainless steel. We have also used the approach successfully for several other materials. This short note summarizes the results of our work in determining process parameters for Ti-6Al-4V using a Concept Laser M2 system.

  7. Printing Outside the Box: Additive Manufacturing Processes for Fabrication of Large Aerospace Structures

    Science.gov (United States)

    Babai, Majid; Peters, Warren

    2015-01-01

    To achieve NASA's mission of space exploration, innovative manufacturing processes are being applied to the fabrication of propulsion elements. Liquid rocket engines (LREs) are comprised of a thrust chamber and nozzle extension as illustrated in figure 1 for the J2X upper stage engine. Development of the J2X engine, designed for the Ares I launch vehicle, is currently being incorporated on the Space Launch System. A nozzle extension is attached to the combustion chamber to obtain the expansion ratio needed to increase specific impulse. If the nozzle extension could be printed as one piece using free-form additive manufacturing (AM) processes, rather than the current method of forming welded parts, a considerable time savings could be realized. Not only would this provide a more homogenous microstructure than a welded structure, but could also greatly shorten the overall fabrication time. The main objective of this study is to fabricate test specimens using a pulsed arc source and solid wire as shown in figure 2. The mechanical properties of these specimens will be compared with those fabricated using the powder bed, selective laser melting technology at NASA Marshall Space Flight Center. As printed components become larger, maintaining a constant temperature during the build process becomes critical. This predictive capability will require modeling of the moving heat source as illustrated in figure 3. Predictive understanding of the heat profile will allow a constant temperature to be maintained as a function of height from substrate while printing complex shapes. In addition, to avoid slumping, this will also allow better control of the microstructural development and hence the properties. Figure 4 shows a preliminary comparison of the mechanical properties obtained.

  8. 3D Machine Vision and Additive Manufacturing: Concurrent Product and Process Development

    International Nuclear Information System (INIS)

    Ilyas, Ismet P

    2013-01-01

    The manufacturing environment rapidly changes in turbulence fashion. Digital manufacturing (DM) plays a significant role and one of the key strategies in setting up vision and strategic planning toward the knowledge based manufacturing. An approach of combining 3D machine vision (3D-MV) and an Additive Manufacturing (AM) may finally be finding its niche in manufacturing. This paper briefly overviews the integration of the 3D machine vision and AM in concurrent product and process development, the challenges and opportunities, the implementation of the 3D-MV and AM at POLMAN Bandung in accelerating product design and process development, and discusses a direct deployment of this approach on a real case from our industrial partners that have placed this as one of the very important and strategic approach in research as well as product/prototype development. The strategic aspects and needs of this combination approach in research, design and development are main concerns of the presentation.

  9. Reactive Additive Stabilization Process (RASP) for hazardous and mixed waste vitrification

    International Nuclear Information System (INIS)

    Jantzen, C.M.; Pickett, J.B.; Ramsey, W.G.

    1993-01-01

    Solidification of hazardous/mixed wastes into glass is being examined at the Savannah River Site (SRS) for (1) nickel plating line (F006) sludges and (2) incinerator wastes. Vitrification of these wastes using high surface area additives, the Reactive Additive Stabilization Process (RASP), has been determined to greatly enhance the dissolution and retention of hazardous, mixed, and heavy metal species in glass. RASP lowers melt temperatures (typically 1050-- 1150 degrees C), thereby minimizing volatility concerns during vitrification. RASP maximizes waste loading (typically 50--75 wt% on a dry oxide basis) by taking advantage of the glass forming potential of the waste. RASP vitrification thereby minimizes waste disposal volume (typically 86--97 vol. %), and maximizes cost savings. Solidification of the F006 plating line sludges containing depleted uranium has been achieved in both soda-lime-silica (SLS) and borosilicate glasses at 1150 degrees C up to waste loadings of 75 wt%. Solidification of incinerator blowdown and mixtures of incinerator blowdown and bottom kiln ash have been achieved in SLS glass at 1150 degrees C up to waste loadings of 50% using RASP. These waste loadings correspond to volume reductions of 86 and 94 volume %, respectively, with large associated savings in storage costs

  10. Safer disclosure of HIV serostatus for women living with HIV who experience or fear violence: a systematic review.

    Science.gov (United States)

    Kennedy, Caitlin E; Haberlen, Sabina; Amin, Avni; Baggaley, Rachel; Narasimhan, Manjulaa

    2015-01-01

    Supporting individuals as they disclose their HIV serostatus may lead to a variety of individual and public health benefits. However, many women living with HIV are hesitant to disclose their HIV status due to fear of negative outcomes such as violence, abandonment, relationship dissolution and stigma. We conducted a systematic review of studies evaluating interventions to facilitate safer disclosure of HIV status for women living with HIV who experience or fear violence. Articles, conference abstracts and programme reports were included if they reported post-intervention evaluation results and were published before 1 April 2015. Searching was conducted through electronic databases for peer-reviewed articles and conference abstracts, reviewing websites of relevant organizations for grey literature, hand searching reference lists of included studies and contacting experts. Systematic methods were used for screening and data abstraction, which was conducted in duplicate. Study quality (rigor) was assessed with the Cochrane risk of bias tool. Two interventions met the inclusion criteria: the Safe Homes and Respect for Everyone cluster-randomized trial of combination HIV and intimate partner violence (IPV) services in Rakai, Uganda, and the South Africa HIV/AIDS Antenatal Post-Test Support study individual randomized trial of an enhanced counselling intervention for pregnant women undergoing HIV testing and counselling. Both programmes integrated screening for IPV into HIV testing services and trained counsellors to facilitate discussions about disclosure based on a woman's risk of violence. However, both were implemented as part of multiple-component interventions, making it impossible to isolate the impact of the safer disclosure components. The existing evidence base for interventions to facilitate safe HIV serostatus disclosure for women who experience or fear violence is limited. Development and implementation of new approaches and rigorous evaluation of safe

  11. [The Bridgelok system for additional retention of bonded prostheses].

    Science.gov (United States)

    Maroto García, J; Gutiérrez Molero, F; López Montero, M V

    1989-04-01

    The partial protesis with metal carving and cemented with composite resin is used frequently as a reversible method in order to substitute teeth, due to the light preparation necessary for the original teeth. Recently, a new system (Bridgelok) with pins has been proposed as safer for this kind of protesis. This paper studies if this new system originates a higher resistance compared to other system without pins.

  12. Bilateral generic working memory circuit requires left-lateralized addition for verbal processing.

    Science.gov (United States)

    Ray, Manaan Kar; Mackay, Clare E; Harmer, Catherine J; Crow, Timothy J

    2008-06-01

    According to the Baddeley-Hitch model, phonological and visuospatial representations are separable components of working memory (WM) linked by a central executive. The traditional view that the separation reflects the relative contribution of the 2 hemispheres (verbal WM--left; spatial WM--right) has been challenged by the position that a common bilateral frontoparietal network subserves both domains. Here, we test the hypothesis that there is a generic WM circuit that recruits additional specialized regions for verbal and spatial processing. We designed a functional magnetic resonance imaging paradigm to elicit activation in the WM circuit for verbal and spatial information using identical stimuli and applied this in 33 healthy controls. We detected left-lateralized quantitative differences in the left frontal and temporal lobe for verbal > spatial WM but no areas of activation for spatial > verbal WM. We speculate that spatial WM is analogous to a "generic" bilateral frontoparietal WM circuit we inherited from our great ape ancestors that evolved, by recruitment of additional left-lateralized frontal and temporal regions, to accommodate language.

  13. Cost estimation of a specifically designed direct light processing (DLP) additive manufacturing machine for precision printing

    DEFF Research Database (Denmark)

    Charalambis, Alessandro; Davoudinejad, Ali; Tosello, Guido

    2017-01-01

    creating new opportunities for manufacturers in a variety of industrial sectors. AM is an essentialprototyping technique for product design and development that is used in many different fields. However, the suitability of AMapplications in actual production in an industrial context needs to be determined......Additive Manufacturing (AM) refers to a portfolio of novel manufacturing technologies based on a layer-by-layer fabrication method.The market and industrial application of additive manufacturing technologies as an established manufacturing process have increasedexponentially in the last years....... This study, presents a cost estimation model forprecision printing with a specifically designed Digital Light Processing (DLP) AM machine built and validated at the Technical Universityof Denmark. The model presented in this study can be easily adapted and applied to estimate within a high level...

  14. A systematic methodology for the design of continuous active pharmaceutical ingredient production processes

    DEFF Research Database (Denmark)

    Cervera Padrell, Albert Emili; Gani, Rafiqul; Kiil, Søren

    2011-01-01

    Continuous pharmaceutical manufacturing (CPM) has emerged as a powerful technology to obtain higher reaction yields and improved separation efficiencies, potentially leading to simplified process flowsheets, reduced total costs, lower environmental impacts, and safer and more flexible production...... and representation, as well as on how to employ this knowledge for process (re-)design. The aim of this paper is to introduce a methodology that systematically identifies already existing PSE methods and tools which can assist in the design of CPM processes. This methodology has been applied to a process...... for the production of an API developed by H. Lundbeck A/S, demonstrating the mentioned potential benefits that CPM can offer....

  15. Risky decisions despite counter evidence: modeling a culture of safer sexual practices.

    Science.gov (United States)

    Patel, Vimla L; Yoskowitz, Nicole A; Kaufman, David R; Gutnik, Lily A; Shortliffe, Edward H

    2005-01-01

    To create a culture of safe practices, we need to understand how and under what conditions the public makes risky decisions about their health. Because risky sexual behaviors are known to be common in young adults, we investigated their decision making regarding sexual activities that could incur a high risk of HIV infection. Sixty young urban adults maintained journals for two weeks and were interviewed regarding condom use and sexual history. We characterized four patterns of condom use behavior: consistent (35.0%), inconsistent (16.7%), consistent to inconsistent (35.0%), and inconsistent to consistent (13.3%). Directionality of reasoning was analyzed in the explanations provided for condom use decisions. The consistent and inconsistent patterns were associated with data-driven heuristic reasoning, where behavior becomes automated and is associated with a high level of confidence in one's judgment. In the other two patterns, the shift in behavior was due to a significant event that influenced a change in directionality to explanation-based reasoning. We discuss these results within the framework of identifying potentially high-risk groups for whom customized intervention strategies (such as computer-based educational programs) can be used to reduce risk, thereby creating a culture of safer sexual practices.

  16. Sending more process data without additional cables

    International Nuclear Information System (INIS)

    Licht, H.; Roiha, R.; Rodych, M.

    1997-01-01

    The as-built data transmission capability in CANDU plants is fully employed. Long delays and high cost make it often not feasible to retrofit plant equipment with additional sensors and bring the data to the office. One of the reasons is the unavoidable addition of data transmission cables. This presentation describes the results of work performed in 1996/97 to network sensors using existing plant infrastructure. To provide an alternative solution, a general purpose data transmission system is being developed. It sends data over existing plant infrastructure such as power wiring and the telephone system. Its components are based on PC technology packaged in a 'black box', using special hardware and software to appear to the user as a very simple, low cost, device. Its drawback is its rather limited transmission speed. This design is in marked contrast to the complexity of present commercial data transmission systems. A point-to-point system has been demonstrated. A networked system is under development. (author)

  17. Are classical process safety concepts relevant to nanotechnology applications?

    International Nuclear Information System (INIS)

    Amyotte, Paul R

    2011-01-01

    The answer to the question posed by the title of this paper is yes - with adaptation to the specific hazards and challenges found in the field of nanotechnology. The validity of this affirmative response is demonstrated by relating key process safety concepts to various aspects of the nanotechnology industry in which these concepts are either already practised or could be further applied. This is accomplished by drawing on the current author's experience in process safety practice and education as well as a review of the relevant literature on the safety of nanomaterials and their production. The process safety concepts selected for analysis include: (i) risk management, (ii) inherently safer design, (iii) human error and human factors, (iv) safety management systems, and (v) safety culture.

  18. Transient Properties of Probability Distribution for a Markov Process with Size-dependent Additive Noise

    Science.gov (United States)

    Yamada, Yuhei; Yamazaki, Yoshihiro

    2018-04-01

    This study considered a stochastic model for cluster growth in a Markov process with a cluster size dependent additive noise. According to this model, the probability distribution of the cluster size transiently becomes an exponential or a log-normal distribution depending on the initial condition of the growth. In this letter, a master equation is obtained for this model, and derivation of the distributions is discussed.

  19. THE RELATIONSHIP BETWEEN SOCIAL, POLICY AND PHYSICAL VENUE FEATURES AND SOCIAL COHESION ON CONDOM USE FOR PREGNANCY PREVENTION AMONG SEX WORKERS: A SAFER INDOOR WORK ENVIRONMENT SCALE

    Science.gov (United States)

    Duff, Putu; Shoveller, Jean; Dobrer, Sabina; Ogilvie, Gina; Montaner, Julio; Chettiar, Jill; Shannon, Kate

    2015-01-01

    Background This study aims to: report on a newly developed ‘Safer Indoor Work Environmental Scale’ that characterizes the social, policy and physical features of indoor venues and social cohesion; and using this scale, longitudinally evaluate the association between these features on sex workers’ (SWs’) condom use for pregnancy prevention. Methods Drawing on a prospective open cohort of female SWs working in indoor venues, a newly-developed ‘Safer Indoor Work Environment Scale’ was used to build six multivariable models with generalized estimating equations (GEE), to determine the independent effects of social, policy and venue-based features and social cohesion on condom use. Results Of 588 indoor SWs, 63.6% used condoms for pregnancy prevention in the last month. In multivariable GEE analysis, the following venue-based features were significantly correlated with barrier contraceptive use for pregnancy prevention: managerial practices and venue safety policies (Adjusted Odds Ratio (AOR)=1.09; 95% Confidence Interval (95%CI) 1.01–1.17) access to sexual and reproductive health services/supplies (AOR=1.10; 95%CI 1.00–1.20) access to drug harm reduction (AOR=1.13; 95%CI 1.01–1.28), and social cohesion among workers (AOR=1.05; 95%CI 1.03–1.07). Access to security features was marginally associated with condom use (AOR=1.13; 95%CI 0.99–1.29). Conclusion The findings of the current study highlight how work environment and social cohesion among SWs are related to improved condom use. Given global calls for the decriminalization of sex work, and potential legislative reforms in Canada, this study points to the critical need for new institutional arrangements (e.g., legal and regulatory frameworks; labour standards) to support safer sex workplaces. PMID:25678713

  20. The relationship between social, policy and physical venue features and social cohesion on condom use for pregnancy prevention among sex workers: a safer indoor work environment scale.

    Science.gov (United States)

    Duff, Putu; Shoveller, Jean; Dobrer, Sabina; Ogilvie, Gina; Montaner, Julio; Chettiar, Jill; Shannon, Kate

    2015-07-01

    This study aims to report on a newly developed Safer Indoor Work Environmental Scale that characterises the social, policy and physical features of indoor venues and social cohesion; and using this scale, longitudinally evaluate the association between these features on sex workers' (SWs') condom use for pregnancy prevention. Drawing on a prospective open cohort of female SWs working in indoor venues, a newly developed Safer Indoor Work Environment Scale was used to build six multivariable models with generalised estimating equations (GEE), to determine the independent effects of social, policy and physical venue-based features and social cohesion on condom use. Of 588 indoor SWs, 63.6% used condoms for pregnancy prevention in the last month. In multivariable GEE analysis, the following venue-based features were significantly correlated with barrier contraceptive use for pregnancy prevention: managerial practices and venue safety policies (adjusted OR (AOR)=1.09; 95% CI 1.01 to 1.17), access to sexual and reproductive health services/supplies (AOR=1.10; 95% CI 1.00 to 1.20), access to drug harm reduction (AOR=1.13; 95% CI 1.01 to 1.28) and social cohesion among workers (AOR=1.05; 95% CI 1.03 to 1.07). Access to security features was marginally associated with condom use (AOR=1.13; 95% CI 0.99 to 1.29). The findings of the current study highlight how work environment and social cohesion among SWs are related to improved condom use. Given global calls for the decriminalisation of sex work, and potential legislative reforms in Canada, this study points to the critical need for new institutional arrangements (eg, legal and regulatory frameworks; labour standards) to support safer sex workplaces. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://group.bmj.com/group/rights-licensing/permissions.

  1. Consolidation & Factors Influencing Sintering Process in Polymer Powder Based Additive Manufacturing

    Science.gov (United States)

    Sagar, M. B.; Elangovan, K.

    2017-08-01

    Additive Manufacturing (AM) is two decade old technology; where parts are build layer manufacturing method directly from a CAD template. Over the years, AM techniques changes the future way of part fabrication with enhanced intricacy and custom-made features are aimed. Commercially polymers, metals, ceramic and metal-polymer composites are in practice where polymers enhanced the expectations in AM and are considered as a kind of next industrial revolution. Growing trend in polymer application motivated to study their feasibility and properties. Laser sintering, Heat sintering and Inhibition sintering are the most successful AM techniques for polymers but having least application. The presentation gives up selective sintering of powder polymers and listed commercially available polymer materials. Important significant factors for effective processing and analytical approaches to access them are discussed.

  2. Vitrification of F006 plating waste sludge by Reactive Additive Stabilization Process (RASP)

    International Nuclear Information System (INIS)

    Martin, H.L.; Jantzen, C.M.; Pickett, J.B.

    1994-01-01

    Solidification into glass of nickel-on-uranium plating wastewater treatment plant sludge (F006 Mixed Waste) has been demonstrated at the Savannah River She (SRS). Vitrification using high surface area additives, the Reactive Additive Stabilization Process (RASP), greatly enhanced the solubility and retention of heavy metals In glass. The bench-scale tests using RASP achieved 76 wt% waste loading In both soda-lime-silica and borosilicate glasses. The RASP has been Independently verified by a commercial waste management company, and a contract awarded to vitrify the approximately 500,000 gallons of stored waste sludge. The waste volume reduction of 89% will greatly reduce the disposal costs, and delisting of the glass waste is anticipated. This will be the world's first commercial-scale vitrification system used for environmental cleanup of Mixed Waste. Its stabilization and volume reduction abilities are expected to set standards for the future of the waste management Industry

  3. Effects of the addition of different nitrogen sources in the tequila fermentation process at high sugar concentration.

    Science.gov (United States)

    Arrizon, J; Gschaedler, A

    2007-04-01

    To study the effect of the addition of different nitrogen sources at high sugar concentration in the tequila fermentation process. Fermentations were performed at high sugar concentration (170 g l(-1)) using Agave tequilana Weber blue variety with and without added nitrogen from different sources (ammonium sulfate; glutamic acid; a mixture of ammonium sulfate and amino acids) during the exponential phase of growth. All the additions increased the fermentation rate and alcohol efficiency. The level of synthesis of volatile compounds depended on the source added. The concentration of amyl alcohols and isobutanol were decreased while propanol and acetaldehyde concentration increased. The most efficient nitrogen sources for fermentation rate were ammonium sulfate and the mixture of ammonium sulfate and amino acids. The level of volatile compounds produced depended upon types of nitrogen. The synthesis of some volatile compounds increased while others decreased with nitrogen addition. The addition of nitrogen could be a strategy for improving the fermentation rate and efficiency in the tequila fermentation process at high sugar Agave tequilana concentration. Furthermore, the sensory quality of the final product may change because the synthesis of the volatile compounds is modified.

  4. Syringaresinol: A Renewable and Safer Alternative to Bisphenol A for Epoxy-Amine Resins.

    Science.gov (United States)

    Janvier, Marine; Hollande, Louis; Jaufurally, Abdus Samad; Pernes, Miguel; Ménard, Raphaël; Grimaldi, Marina; Beaugrand, Johnny; Balaguer, Patrick; Ducrot, Paul-Henri; Allais, Florent

    2017-02-22

    A renewable bisepoxide, SYR-EPO, was prepared from syringaresinol, a naturally occurring bisphenol deriving from sinapic acid, by using a chemo-enzymatic synthetic pathway. Estrogenic activity tests revealed no endocrine disruption for syringaresinol. Its glycidylation afforded SYR-EPO with excellent yield and purity. This biobased, safe epoxy precursor was then cured with conventional and renewable diamines for the preparation of epoxy-amine resins. The resulting thermosets were thermally and mechanically characterized. Thermal analyses of these new resins showed excellent thermal stabilities (T d5 % =279-309 °C) and T g ranging from 73 to 126 °C, almost reaching the properties of those obtained with the diglycidylether of bisphenol A (DGEBA), extensively used in the polymer industry (T d5 % =319 °C and T g =150 °C for DGEBA/isophorone diamine resins). Degradation studies in NaOH and HCl aqueous solutions also highlighted the robustness of the syringaresinol-based resins, similar to bisphenol A (BPA). All these results undoubtedly confirmed the potential of syringaresinol as a greener and safer substitute for BPA. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. The mechanical problems on additive manufacturing of viscoelastic solids with integral conditions on a surface increasing in the growth process

    Science.gov (United States)

    Parshin, D. A.; Manzhirov, A. V.

    2018-04-01

    Quasistatic mechanical problems on additive manufacturing aging viscoelastic solids are investigated. The processes of piecewise-continuous accretion of such solids are considered. The consideration is carried out in the framework of linear mechanics of growing solids. A theorem about commutativity of the integration over an arbitrary surface increasing in the solid growing process and the time-derived integral operator of viscoelasticity with a limit depending on the solid point is proved. This theorem provides an efficient way to construct on the basis of Saint-Venant principle solutions of nonclassical boundary-value problems for describing the mechanical behaviour of additively formed solids with integral satisfaction of boundary conditions on the surfaces expanding due to the additional material influx to the formed solid. The constructed solutions will retrace the evolution of the stress-strain state of the solids under consideration during and after the processes of their additive formation. An example of applying the proved theorem is given.

  6. 3D-Printing: How Additive Manufacturing impacts Supply Chain Business Processes and Management Components

    OpenAIRE

    Oettmeier, Katrin; Hofmann, Erik

    2016-01-01

    Purpose The business implications of additive manufacturing (AM) are explored; specific focus thereby lies on the impact of AM technology adoption in customized parts production. Design/methodology/approach Based on two explorative case studies from the hearing aid industry, the impact of AM technology adoption on supply chain business processes and management components is analyzed. General systems theory and a supply chain management framework serve as theoretical underpinning....

  7. Real-time interferometric monitoring and measuring of photopolymerization based stereolithographic additive manufacturing process: sensor model and algorithm

    International Nuclear Information System (INIS)

    Zhao, X; Rosen, D W

    2017-01-01

    As additive manufacturing is poised for growth and innovations, it faces barriers of lack of in-process metrology and control to advance into wider industry applications. The exposure controlled projection lithography (ECPL) is a layerless mask-projection stereolithographic additive manufacturing process, in which parts are fabricated from photopolymers on a stationary transparent substrate. To improve the process accuracy with closed-loop control for ECPL, this paper develops an interferometric curing monitoring and measuring (ICM and M) method which addresses the sensor modeling and algorithms issues. A physical sensor model for ICM and M is derived based on interference optics utilizing the concept of instantaneous frequency. The associated calibration procedure is outlined for ICM and M measurement accuracy. To solve the sensor model, particularly in real time, an online evolutionary parameter estimation algorithm is developed adopting moving horizon exponentially weighted Fourier curve fitting and numerical integration. As a preliminary validation, simulated real-time measurement by offline analysis of a video of interferograms acquired in the ECPL process is presented. The agreement between the cured height estimated by ICM and M and that measured by microscope indicates that the measurement principle is promising as real-time metrology for global measurement and control of the ECPL process. (paper)

  8. Data-driven multi-scale multi-physics models to derive process-structure-property relationships for additive manufacturing

    Science.gov (United States)

    Yan, Wentao; Lin, Stephen; Kafka, Orion L.; Lian, Yanping; Yu, Cheng; Liu, Zeliang; Yan, Jinhui; Wolff, Sarah; Wu, Hao; Ndip-Agbor, Ebot; Mozaffar, Mojtaba; Ehmann, Kornel; Cao, Jian; Wagner, Gregory J.; Liu, Wing Kam

    2018-01-01

    Additive manufacturing (AM) possesses appealing potential for manipulating material compositions, structures and properties in end-use products with arbitrary shapes without the need for specialized tooling. Since the physical process is difficult to experimentally measure, numerical modeling is a powerful tool to understand the underlying physical mechanisms. This paper presents our latest work in this regard based on comprehensive material modeling of process-structure-property relationships for AM materials. The numerous influencing factors that emerge from the AM process motivate the need for novel rapid design and optimization approaches. For this, we propose data-mining as an effective solution. Such methods—used in the process-structure, structure-properties and the design phase that connects them—would allow for a design loop for AM processing and materials. We hope this article will provide a road map to enable AM fundamental understanding for the monitoring and advanced diagnostics of AM processing.

  9. Data-driven multi-scale multi-physics models to derive process-structure-property relationships for additive manufacturing

    Science.gov (United States)

    Yan, Wentao; Lin, Stephen; Kafka, Orion L.; Lian, Yanping; Yu, Cheng; Liu, Zeliang; Yan, Jinhui; Wolff, Sarah; Wu, Hao; Ndip-Agbor, Ebot; Mozaffar, Mojtaba; Ehmann, Kornel; Cao, Jian; Wagner, Gregory J.; Liu, Wing Kam

    2018-05-01

    Additive manufacturing (AM) possesses appealing potential for manipulating material compositions, structures and properties in end-use products with arbitrary shapes without the need for specialized tooling. Since the physical process is difficult to experimentally measure, numerical modeling is a powerful tool to understand the underlying physical mechanisms. This paper presents our latest work in this regard based on comprehensive material modeling of process-structure-property relationships for AM materials. The numerous influencing factors that emerge from the AM process motivate the need for novel rapid design and optimization approaches. For this, we propose data-mining as an effective solution. Such methods—used in the process-structure, structure-properties and the design phase that connects them—would allow for a design loop for AM processing and materials. We hope this article will provide a road map to enable AM fundamental understanding for the monitoring and advanced diagnostics of AM processing.

  10. Flow Characteristics of a Thermoset Fiber Composite Photopolymer Resin in a Vat Polymerization Additive Manufacturing Process

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Spangenberg, Jon; Pedersen, David B.

    Additive manufacturing vat polymerization has become a leading technology and gained a massive amount of attention in industrial applications such as injection molding inserts. By the use of the thermoset polymerization process inserts have increased their market share. For most industrial...... applications, strength and stiffness are crucial factors to a successful implementation of cured photopolymer thermosets. Hence, fiber-reinforced polymers have recently been introduced. The behavior and especially orientation of fibers during the vat photopolymerization process has yet not been fully...

  11. Modeling of Processing-Induced Pore Morphology in an Additively-Manufactured Ti-6Al-4V Alloy.

    Science.gov (United States)

    Kabir, Mohammad Rizviul; Richter, Henning

    2017-02-08

    A selective laser melting (SLM)-based, additively-manufactured Ti-6Al-4V alloy is prone to the accumulation of undesirable defects during layer-by-layer material build-up. Defects in the form of complex-shaped pores are one of the critical issues that need to be considered during the processing of this alloy. Depending on the process parameters, pores with concave or convex boundaries may occur. To exploit the full potential of additively-manufactured Ti-6Al-4V, the interdependency between the process parameters, pore morphology, and resultant mechanical properties, needs to be understood. By incorporating morphological details into numerical models for micromechanical analyses, an in-depth understanding of how these pores interact with the Ti-6Al-4V microstructure can be gained. However, available models for pore analysis lack a realistic description of both the Ti-6Al-4V grain microstructure, and the pore geometry. To overcome this, we propose a comprehensive approach for modeling and discretizing pores with complex geometry, situated in a polycrystalline microstructure. In this approach, the polycrystalline microstructure is modeled by means of Voronoi tessellations, and the complex pore geometry is approximated by strategically combining overlapping spheres of varied sizes. The proposed approach provides an elegant way to model the microstructure of SLM-processed Ti-6Al-4V containing pores or crack-like voids, and makes it possible to investigate the relationship between process parameters, pore morphology, and resultant mechanical properties in a finite-element-based simulation framework.

  12. Modeling of Processing-Induced Pore Morphology in an Additively-Manufactured Ti-6Al-4V Alloy

    Directory of Open Access Journals (Sweden)

    Mohammad Rizviul Kabir

    2017-02-01

    Full Text Available A selective laser melting (SLM-based, additively-manufactured Ti-6Al-4V alloy is prone to the accumulation of undesirable defects during layer-by-layer material build-up. Defects in the form of complex-shaped pores are one of the critical issues that need to be considered during the processing of this alloy. Depending on the process parameters, pores with concave or convex boundaries may occur. To exploit the full potential of additively-manufactured Ti-6Al-4V, the interdependency between the process parameters, pore morphology, and resultant mechanical properties, needs to be understood. By incorporating morphological details into numerical models for micromechanical analyses, an in-depth understanding of how these pores interact with the Ti-6Al-4V microstructure can be gained. However, available models for pore analysis lack a realistic description of both the Ti-6Al-4V grain microstructure, and the pore geometry. To overcome this, we propose a comprehensive approach for modeling and discretizing pores with complex geometry, situated in a polycrystalline microstructure. In this approach, the polycrystalline microstructure is modeled by means of Voronoi tessellations, and the complex pore geometry is approximated by strategically combining overlapping spheres of varied sizes. The proposed approach provides an elegant way to model the microstructure of SLM-processed Ti-6Al-4V containing pores or crack-like voids, and makes it possible to investigate the relationship between process parameters, pore morphology, and resultant mechanical properties in a finite-element-based simulation framework.

  13. INVESTIGATION ON UTILITY OF PLASTIC WASTE AS AN ADDITIVE FOR BITUMINOUS CONCRETE USING WET PROCESS OF MIXING

    Directory of Open Access Journals (Sweden)

    Anurag Virendra Tiwari

    2017-12-01

    Full Text Available Purpose. Plastic waste has become a major environmental issue of concern due to its exponential growth due to rapid urbanization. The paper investigates utility of plastic waste as an additive for bituminous concrete using wet process of mixing. Methodology. The methodology for the present paper has been designed with complex research consisting of Marshall mix design of the bituminous mix added with plastic waste for modifying bitumen using wet process of mixing, performing the tests on the samples and analyzing the results in the form of table and figures. In the present paper LDPE and HDPE type of plastic waste are used to modify the bitumen. Finding. The results show that addition of 6 percent of bitumen improves the Marshall properties of the mix. Use of plastic to modify the bitumen not only makes the road surface more durable but also it is an eco-friendly way of proper disposal of plastic waste. Originality. The processes used for mixing the plastic waste to the bitumen are dry process and wet process. Dry process of mixing the plastic waste to the bituminous mix is most common and lot of study is carried out on its application. In the present paper wet process of mixing has not yet been studied much. Practical Value. The practical application of utilizing the plastic waste to modify bitumen in the bituminous mix improves the stability values resulting in the more durable road surface. Also the method ensures the proper disposal of plastic waste in eco-friendly way.

  14. Effects of trace element addition on process stability during anaerobic co-digestion of OFMSW and slaughterhouse waste.

    Science.gov (United States)

    Moestedt, J; Nordell, E; Shakeri Yekta, S; Lundgren, J; Martí, M; Sundberg, C; Ejlertsson, J; Svensson, B H; Björn, A

    2016-01-01

    This study used semi-continuous laboratory scale biogas reactors to simulate the effects of trace-element addition in different combinations, while degrading the organic fraction of municipal solid waste and slaughterhouse waste. The results show that the combined addition of Fe, Co and Ni was superior to the addition of only Fe, Fe and Co or Fe and Ni. However, the addition of only Fe resulted in a more stable process than the combined addition of Fe and Co, perhaps indicating a too efficient acidogenesis and/or homoacetogenesis in relation to a Ni-deprived methanogenic population. The results were observed in terms of higher biogas production (+9%), biogas production rates (+35%) and reduced VFA concentration for combined addition compared to only Fe and Ni. The higher stability was supported by observations of differences in viscosity, intraday VFA- and biogas kinetics as well as by the 16S rRNA gene and 16S rRNA of the methanogens. Copyright © 2015 Elsevier Ltd. All rights reserved.

  15. Time and temperature reduction of the sealing process of porous aluminium oxide films with organic additives

    International Nuclear Information System (INIS)

    Bautista, A.; Lopez, V.; Otero, E.; Lizarbe, R.; Gonzalez, J.A.

    1998-01-01

    Different sealing processes of anode coating in aluminium oxide have been industrially used for more than 30 years. In two of the preceding decades a great effort was realized to reduce costs in the traditional hydrothermal sealing in deionized boiling water (SHT), a very expensive process due to its endurance and high temperature on which it develops. New sealing procedures are proposed, on which by means of the use of organic additives, the time or the temperature of the SHT is essentially reduced. (Author) 10 refs

  16. Log-normal distribution from a process that is not multiplicative but is additive.

    Science.gov (United States)

    Mouri, Hideaki

    2013-10-01

    The central limit theorem ensures that a sum of random variables tends to a Gaussian distribution as their total number tends to infinity. However, for a class of positive random variables, we find that the sum tends faster to a log-normal distribution. Although the sum tends eventually to a Gaussian distribution, the distribution of the sum is always close to a log-normal distribution rather than to any Gaussian distribution if the summands are numerous enough. This is in contrast to the current consensus that any log-normal distribution is due to a product of random variables, i.e., a multiplicative process, or equivalently to nonlinearity of the system. In fact, the log-normal distribution is also observable for a sum, i.e., an additive process that is typical of linear systems. We show conditions for such a sum, an analytical example, and an application to random scalar fields such as those of turbulence.

  17. Additional application areas of the 3D process information display; Weiterfuehrende Einsatzgebiete des 3-D-Prozessinformationsdisplays

    Energy Technology Data Exchange (ETDEWEB)

    Meissner, K. [Institut fuer Automatisierung und Informatik GmbH, Zentrum fuer industrielle Forschung und Entwicklung, Wernigerode (Germany); Hensel, H. [Hochschule Harz, Fachbereich Automatisierung und Informatik, Wernigerode (Germany)

    2007-07-01

    The current technological progress in the process industry results in a significant increase of the complexity of control systems. The amount of supervised information grows constantly for each operator because of a higher level of automation and an optimized information acquisition of the control systems. This development results in a cognitive overload of the operator which causes incorrect behaviour and responses in alert situations. In technical literature, several approaches are discussed to counteract this problem. This paper presents the newly developed 3-D Process Information Display (3D-PID) and describes which additional application areas as a primary representation method to the supervision of complex process conditions are imaginable. The 3D-PID is based on a cognitive scenic representation of the process values within a 3-D process room. Particularly the problem of the overview and detail presentation known from the literature is discussed. (orig.)

  18. A new continuous-flow process for catalytic conversion of glycerol to oxygenated fuel additive: Catalyst screening

    International Nuclear Information System (INIS)

    Nanda, Malaya R.; Yuan, Zhongshun; Qin, Wensheng; Ghaziaskar, Hassan S.; Poirier, Marc-Andre; Xu, Chunbao

    2014-01-01

    Highlights: • A continuous-flow process for catalytic synthesis of solketal from glycerol. • Six different heterogeneous acid catalysts were studied in the process. • Glycerol conversion and solketal yield of 90% and 88% respectively were achieved. • The process has the potential to be scaled-up for industrial applications. - Abstract: A new continuous-flow reactor was designed for the conversion of glycerol to solketal, an oxygenated fuel additive, through ketalization with acetone. Six heterogeneous catalysts were investigated with respect to their catalytic activity and stability in a flow reactor. The acidity of the catalysts positively influences the catalyst’s activity. Among all the solid acid catalysts tested, the maximum solketal yield from experiments at 40 °C, 600 psi and WHSV of 4 h −1 attained 73% and 88% at the acetone/glycerol molar ratio of 2.0 and 6.0, respectively, with Amberlyst Wet. Based on the solketal yield and glycerol conversion results, the activity of all catalysts tested follows the following order of sequence: Amberlyst Wet ≈ Zeolite ≈ Amberlyst Dry > Zirconium Sulfate > Montmorillonite > Polymax. An increase in acetone/glycerol molar ratio or a decrease in WHSV enhanced the glycerol conversion as expected. This process offers an attractive route for converting glycerol, the main by-product of biodiesel, to solketal – a value-added green product with potential industrial applications as a valuable fuel additive or combustion promoter for gasoline engines

  19. PROCESSING OF MULTI-DIGIT ADDITIONS IN HIGH MATH-ANXIOUS INDIVIDUALS: PSYCHOPHYSIOLOGICAL EVIDENCE

    Directory of Open Access Journals (Sweden)

    MARIA ISABEL eNÚÑEZ-PEÑA

    2015-08-01

    Full Text Available We investigated the time course of neural processing of multi-digit additions in high- (HMA and low-math anxious (LMA individuals. Seventeen HMA and 17 LMA individuals were presented with two-digit additions and were asked to perform a verification task. Behavioral data showed that HMA were slower and more error prone than their LMA peers, and that incorrect solutions were solved more slowly and less accurately than correct ones. Moreover, HMA individuals tended to need more time and commit more errors when having to verify incorrect solutions than correct ones. They also took longer and made more errors than their LMA peers. ERPs time-locked to the presentation of the addends (calculation phase and to the presentation of the proposed solution (verification phase were also analyzed. In both phases, a P2 component of larger amplitude was found for HMA individuals than for their LMA peers. Moreover, in the verification phase, LMA individuals showed a larger late positive component (LPC for incorrect solutions at parietal electrodes than their HMA counterparts. Because the P2 component is considered to be a biomarker of the mobilization of attentional resources towards emotionally negative stimuli, these results suggest that HMA individuals may invest more attentional resources during the arithmetical

  20. Comparison of the effect of benzoic acid addition on the fermentation process quality with untreated silages

    Directory of Open Access Journals (Sweden)

    Petr Doležal

    2004-01-01

    Full Text Available The influence of benzoic acid and formic acid (positive control of ensilaged maize and pressed sugar beet pulp on quality fermentation processes was studied in a laboratory experiment. The effect of additive on the quality of fermentation process during maize ensiling was studied in a first model experiment. Preservatives such as formic acid and benzoic acid were added to ensiled maize at the concentration of 1L/t and 1 kg/t, respectively. When benzoic acid was used as a preservative, the pH and the N-NH3/ N total ratio decreased statistically (PSugar beet pulp silages with benzoic acid or formic acid after 32 days of storage had a better sensuous evaluation than the control silage. The most intensive decrease of pH value was observed after formic acid addition as compared with control silage. The statistically significantly (P<0.05 highest lactic acid content (49.64 ± 0.28 as well as the highest ratio of LA/VFA were found in the sugar beet pulp silage with benzoic acid. Lactic acid constituted the highest percentage (P<0.05 of all fermentation acids in the silage with benzoic acid additive (65.12 ± 0.80. Undesirable butyric acid (BA was not found in any variant of silages. The positive correlation between the titration acidity and acids sum in dry matter of silage conserved with formic acid was found. The additive of organic acids reduced significantly TA and fermentation acids content. Between the pH value and lactic acid content, no correlation was found.

  1. Effects of V{sub 2}O{sub 5} addition on NiZn ferrite synthesized using two-step sintering process

    Energy Technology Data Exchange (ETDEWEB)

    Hu Jun [College of Chemical Engineering and Materials Science, Zhejiang University of Technology, Hangzhou 310032 (China); State Key Laboratory of Silicon Materials, Zhejiang University, Hangzhou 310027 (China); Shi Gang; Ni Zheming; Zheng Li [College of Chemical Engineering and Materials Science, Zhejiang University of Technology, Hangzhou 310032 (China); Chen Aimin, E-mail: hjzjut@zjut.edu.cn [College of Chemical Engineering and Materials Science, Zhejiang University of Technology, Hangzhou 310032 (China)

    2012-06-15

    The combined influence of a two-step sintering (TSS) process and addition of V{sub 2}O{sub 5} on the microstructure and magnetic properties of NiZn ferrite was investigated. As comparison, samples prepared by the conventional single-step sintering (SSS) procedure were also studied. It was found that with 0.3 wt% V{sub 2}O{sub 5} additive, the sample sintered by the two-step sintering process at a high temperature of 1250 Degree-Sign C for 30 min and a lower temperature of 1180 Degree-Sign C for 3 h exhibited more homogeneous microstructure and higher permeability with a high Q-factor. The results showed that the TSS method with suitable additive brought positive improvement of the microstructure and magnetic properties of NiZn ferrite.

  2. In Situ 3D Monitoring of Geometric Signatures in the Powder-Bed-Fusion Additive Manufacturing Process via Vision Sensing Methods.

    Science.gov (United States)

    Li, Zhongwei; Liu, Xingjian; Wen, Shifeng; He, Piyao; Zhong, Kai; Wei, Qingsong; Shi, Yusheng; Liu, Sheng

    2018-04-12

    Lack of monitoring of the in situ process signatures is one of the challenges that has been restricting the improvement of Powder-Bed-Fusion Additive Manufacturing (PBF AM). Among various process signatures.

  3. Thermal processing of EVA encapsulants and effects of formulation additives

    Energy Technology Data Exchange (ETDEWEB)

    Pern, F.J.; Glick, S.H. [National Renewable Energy Lab., Golden, CO (United States)

    1996-05-01

    The authors investigated the in-situ processing temperatures and effects of various formulation additives on the formation of ultraviolet (UV) excitable chromophores, in the thermal lamination and curing of ethylene-vinyl acetate (EVA) encapsulants. A programmable, microprocessor-controlled, double-bag vacuum laminator was used to study two commercial as formulated EVA films, A9918P and 15295P, and solution-cast films of Elvaxrm (EVX) impregnated with various curing agents and antioxidants. The results show that the actual measured temperatures of EVA lagged significantly behind the programmed profiles for the heating elements and were affected by the total thermal mass loaded inside the laminator chamber. The antioxidant Naugard P{trademark}, used in the two commercial EVA formulations, greatly enhances the formation of UV-excitable, short chromophores upon curing, whereas other tested antioxidants show little effect. A new curing agent chosen specifically for the EVA formulation modification produces little or no effect on chromophore formation, no bubbling problems in the glass/EVX/glass laminates, and a gel content of {approximately}80% when cured at programmed 155{degrees}C for 4 min. Also demonstrated is the greater discoloring effect with higher concentrations of curing-generated chromophores.

  4. An instrumentation and control philosophy for high-level nuclear waste processing facilities

    International Nuclear Information System (INIS)

    Weigle, D.H.

    1990-01-01

    The purpose of this paper is to present an instrumentation and control philosophy which may be applied to high-level nuclear waste processing facilities. This philosophy describes the recommended criteria for automatic/manual control, remote/local control, remote/local display, diagnostic instrumentation, interlocks, alarm levels, and redundancy. Due to the hazardous nature of the process constituents of a high-level nuclear waste processing facility, it is imperative that safety and control features required for accident-free operation and maintenance be incorporated. A well-instrumented and controlled process, while initially more expensive in capital and design costs, is generally safer and less expensive to operate. When the long term cost savings of a well designed process is coupled with the high savings enjoyed by accident avoidance, the benefits far outweigh the initial capital and design costs

  5. The Effect Of Additional Detergent In Crude Palm Oil In The Process Of Separation Stearin

    Science.gov (United States)

    Rezekyah Hasibuan, Vina; aini, Nur; Febriyanti; Ayubi Pane, Salahudin Al

    2018-03-01

    This study aims to find out how much stearin is formed from the addition of detergent and to understand the process of separation of crude olein with crude stearin from raw material of crude palm oil (CPO). Using a detergent fractionation system, detergent fractionation is a continuous crystallization of oil with controlled cooling and the separation of fractions by weight or centrifuge after supplementing surfactant.

  6. Safer Nanomaterials and Nanomanufacturing

    Science.gov (United States)

    2013-02-01

    objective of this work was to generate crucial ecotoxicological data of metal nanoparticles (NPs) on the environmentally ubiquitous ammonia oxidizing...Nanostructured TiO2 into the Patterned Biosilica of the Diatom Pinnularia sp. by a Two-Stage Bioreactor Cultivation Process. ACS Nano 2008, 2 (10

  7. Comparing the Governance of Novel Products and Processes of Biotechnology

    DEFF Research Database (Denmark)

    Hansen, Janus

    The emergence of novel products and processes of biotechnology in medicine, industry and agriculture has been accompanied by promises of healthier, safer and more productive lives and societies. However, biotechnology has also served as cause and catalyst of social controversy about the physical...... to start to fill this gap and develop a conceptual framework for comparing and analysing new and emerging modes of governance affiliated with biotechnology in the light of more general approaches to governance. We aim for a framework that can facilitate comparative inquiries and learning across different...

  8. Effects of additional isoscalar vector bosons in e+e-→ff-bar processes at the TRISTAN and LEP energies

    International Nuclear Information System (INIS)

    Pankov, A.A.; Gershtejn, S.S.; Likhoded, A.A.; Yushchenko, O.P.

    1991-01-01

    The phenomenological manifestation of the additional Y(Y L ) boson arising in the models with the composite structure of electroweak interactions is studied for the process e + e - →ff-bar at the TRISTAN and LEP energies. It is shown that the presence of the additional isoscalar boson, yields a measurable effect in the cross-section of e + e - →μ + μ - (hadrons) processes at LEP. This effect in the muon and hadron cross-sections at the energies M Z ±Γ Z /2 can be ∼1.5-2% for small values of the γ-Y-mixing parameter. 13 refs

  9. Effect of additive on electrochemical corrosion properties of plasma electrolytic oxidation coatings formed on CP Ti under different processing frequency

    Energy Technology Data Exchange (ETDEWEB)

    Babaei, Mahdi, E-mail: mahdi.babaei@ut.ac.ir; Dehghanian, Changiz; Vanaki, Mojtaba

    2015-12-01

    Highlights: • PEO coatings formed on Cp Ti from phosphate electrolyte with zirconate additive. • The SEM results provide information of microdischarge behavior. • The effect of additive on structure and long-term corrosion behavior was investigated. • The additive influence on coating performance varies with processing frequency. - Abstract: The plasma electrolytic oxidation (PEO) coating containing zirconium oxide was fabricated on CP Ti at different processing frequencies viz., 100 Hz and 1000 Hz in a (Na{sub 2}ZrO{sub 3}, Na{sub 2}SiO{sub 3})-additive containing NaH{sub 2}PO{sub 4}-based solution, and long-term electrochemical corrosion behavior of the coatings was studied using electrochemical impedance spectroscopy (EIS) in 3.5 wt.% NaCl solution. Electrochemical degradation behavior of two-layered coatings formed at different frequencies was turned out to be governed by concentration of electrolyte additive. With increasing additive concentration, the coating obtained at frequency of 1000 Hz exhibited enhanced corrosion resistance. However, corrosion resistance of the coating prepared at 100 Hz was found to decrease with increased additive, which was attributed to intensified microdischarges damaging the protective effect of inner layer. Nevertheless, the electrolyte additive was found to mitigate the long-term degradation of the coatings to a significant extent.

  10. Should we consider steps with variable height for a safer stair negotiation in older adults?

    Science.gov (United States)

    Kunzler, Marcos R; da Rocha, Emmanuel S; Dos Santos, Christielen S; Ceccon, Fernando G; Priario, Liver A; Carpes, Felipe P

    2018-01-01

    Effects of exercise on foot clearances are important. In older adults variations in foot clearances during walking may lead to a fall, but there is a lack of information concerning stair negotiation in older adults. Whether a condition of post exercise changes foot clearances between steps of a staircase in older adults still unknown. To determine differences in clearances when older adults negotiate different steps of a staircase before and after a session of aerobic exercise. Kinematics data from 30 older adults were acquired and the toe and heel clearances were determined for each step. Clearances were compared between the steps. Smaller clearances were found at the highest step during ascending and descending, which was not changed by exercise. Smaller clearances suggest higher risk of tripping at the top of the staircase, regardless of exercise. A smaller step at the top of a short flight of stairs could reduce chances of tripping in older adults. It suggests that steps with variable height could make stair negotiation safer in older adults. This hypothesis should be tested in further studies.

  11. Scale-up of the Reversible Addition-Fragmentation Chain Transfer (RAFT Polymerization Using Continuous Flow Processing

    Directory of Open Access Journals (Sweden)

    Nenad Micic

    2014-01-01

    Full Text Available A controlled radical polymerization process using the Reversible Addition-Fragmentation Chain Transfer (RAFT approach was scaled up by a factor of 100 from a small laboratory scale of 5 mL to a preparative scale of 500 mL, using batch and continuous flow processing. The batch polymerizations were carried out in a series of different glass vessels, using either magnetic or overhead stirring, and different modes of heating: Microwave irradiation or conductive heating in an oil bath. The continuous process was conducted in a prototype tubular flow reactor, consisting of 6 mm ID stainless steel tubing, fitted with static mixers. Both reactor types were tested for polymerizations of the acid functional monomers acrylic acid and 2-acrylamido-2-methylpropane-1-sulfonic acid in water at 80 °C with reaction times of 30 to 40 min. By monitoring the temperature during the exothermic polymerization process, it was observed that the type and size of reactor had a significant influence on the temperature profile of the reaction.

  12. Macro-/Micro-Controlled 3D Lithium-Ion Batteries via Additive Manufacturing and Electric Field Processing.

    Science.gov (United States)

    Li, Jie; Liang, Xinhua; Liou, Frank; Park, Jonghyun

    2018-01-30

    This paper presents a new concept for making battery electrodes that can simultaneously control macro-/micro-structures and help address current energy storage technology gaps and future energy storage requirements. Modern batteries are fabricated in the form of laminated structures that are composed of randomly mixed constituent materials. This randomness in conventional methods can provide a possibility of developing new breakthrough processing techniques to build well-organized structures that can improve battery performance. In the proposed processing, an electric field (EF) controls the microstructures of manganese-based electrodes, while additive manufacturing controls macro-3D structures and the integration of both scales. The synergistic control of micro-/macro-structures is a novel concept in energy material processing that has considerable potential for providing unprecedented control of electrode structures, thereby enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.

  13. Characterization of semi-solid processing of aluminium alloy 7075 with Sc and Zr additions

    Energy Technology Data Exchange (ETDEWEB)

    Rogal, Ł., E-mail: l.rogal@imim.pl [Institute of Metallurgy and Materials Science of the Polish Academy of Sciences, 25 Reymonta St., 30-059 Krakow (Poland); Dutkiewicz, J. [Institute of Metallurgy and Materials Science of the Polish Academy of Sciences, 25 Reymonta St., 30-059 Krakow (Poland); Atkinson, H.V. [The University of Leicester, Department of Engineering University Road, Leicester, LE1 7RH (United Kingdom); Lityńska-Dobrzyńska, L.; Czeppe, T. [Institute of Metallurgy and Materials Science of the Polish Academy of Sciences, 25 Reymonta St., 30-059 Krakow (Poland); Modigell, M. [RWTH Aachen—Department of Mechanical Process Engineering, 55 Templergraben St., Aachen (Germany)

    2013-09-15

    For thixoforming (semi-solid processing) it is necessary to have a fine globular microstructure in a semi-solid range. Here this has been obtained for 7075 aluminium alloy by addition of modifying agents: 0.5 weight % of scandium and zirconium. The thixoforming process was carried out at 632 °C which gave about 23 volume % of liquid phase. The microstructure of the thixo-formed part (a rotor) consisted of globular grains surrounded by precipitates of secondary phase. The average hardness of thixo-formed parts was 105 HV{sub 5} and the tensile strength 300 MPa. T6 heat treatments were performed with solutionisation at 450 °C for 30 min and 10 h. In both cases the ageing time was set as 18 h at 120 °C. The heat treatments led to an increase in average tensile strength up to 495 MPa. Transmission Electron Microscopy (TEM) analysis enabled the identification of precipitates of the metastable dispersoids of L1{sub 2}–Al{sub 3} (Zr, Sc) and η′ (MgZn{sub 2}) phases in the alloy after the thixoforming and T6 treatment. The measurements of rheological properties of 7075Al alloy with Sc and Zr additions in the semi-solid range indicated an increase of particle size and spheroidization leading to an observable decrease of viscosity during isothermal shearing. A shear rate jump experiment showed that with increasing shear rate the viscosity rapidly falls.

  14. Silver Nanocube and Nanobar Growth via Anisotropic Monomer Addition and Particle Attachment Processes

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Dongdong [Physical; Wu, Zhigang [School; Song, Miao [Physical; Chun, Jaehun [Physical; Schenter, Gregory K. [Physical; Li, Dongsheng [Physical

    2018-01-11

    Understanding the growth mechanism of noble metal nanocrystals during solution synthesis is of significant importance for shape and property control. However, much remains unknown about the growth pathways of metal nanoparticles due to lack of direct observation. Using an in-situ transmission electron microscopy technique, we directly observed Ag nanocube and nanobar growth in aqueous solution through both classical monomer-by-monomer addition and non-classical particle attachment processes. During the particle attachment process, Ag nanocubes and nanobars formed via both oriented and non-oriented attachment. Our calculations, along with dynamics of the observed attachment, showed that van der Waals force overcame hydrodynamic and friction forces and drove the particles toward each other. During classical growth, an anisotropic growth was also revealed, and the resulting unsymmetrical shape constituted an intermediate state for Ag nanocube growth. We hypothesized that the temporary symmetry breaking resulted from different growth rates on {001} surfaces due to a local surface concentration variation caused by the imbalance between the consumption of Ag+ near the surface and the diffusion of Ag+ from bulk to surface.

  15. Manufacturing Process Simulation of Large-Scale Cryotanks

    Science.gov (United States)

    Babai, Majid; Phillips, Steven; Griffin, Brian

    2003-01-01

    NASA's Space Launch Initiative (SLI) is an effort to research and develop the technologies needed to build a second-generation reusable launch vehicle. It is required that this new launch vehicle be 100 times safer and 10 times cheaper to operate than current launch vehicles. Part of the SLI includes the development of reusable composite and metallic cryotanks. The size of these reusable tanks is far greater than anything ever developed and exceeds the design limits of current manufacturing tools. Several design and manufacturing approaches have been formulated, but many factors must be weighed during the selection process. Among these factors are tooling reachability, cycle times, feasibility, and facility impacts. The manufacturing process simulation capabilities available at NASA.s Marshall Space Flight Center have played a key role in down selecting between the various manufacturing approaches. By creating 3-D manufacturing process simulations, the varying approaches can be analyzed in a virtual world before any hardware or infrastructure is built. This analysis can detect and eliminate costly flaws in the various manufacturing approaches. The simulations check for collisions between devices, verify that design limits on joints are not exceeded, and provide cycle times which aide in the development of an optimized process flow. In addition, new ideas and concerns are often raised after seeing the visual representation of a manufacturing process flow. The output of the manufacturing process simulations allows for cost and safety comparisons to be performed between the various manufacturing approaches. This output helps determine which manufacturing process options reach the safety and cost goals of the SLI. As part of the SLI, The Boeing Company was awarded a basic period contract to research and propose options for both a metallic and a composite cryotank. Boeing then entered into a task agreement with the Marshall Space Flight Center to provide manufacturing

  16. Safety culture and the 5 steps to safer surgery: an intervention study.

    Science.gov (United States)

    Hill, M R; Roberts, M J; Alderson, M L; Gale, T C E

    2015-06-01

    Improvements in safety culture have been postulated as one of the mechanisms underlying the association between the introduction of the World Health Organisation (WHO) Surgical Safety Checklist with perioperative briefings and debriefings, and enhanced patient outcomes. The 5 Steps to Safer Surgery (5SSS) incorporates pre-list briefings, the three steps of the WHO Surgical Safety Checklist (SSC) and post-list debriefings in one framework. We aimed to identify any changes in safety culture associated with the introduction of the 5SSS in orthopaedic operating theatres. We assessed the safety culture in the elective orthopaedic theatres of a large UK teaching hospital before and after introduction of the 5SSS using a modified version of the Safety Attitude Questionnaire - Operating Room (SAQ-OR). Primary outcome measures were pre-post intervention changes in the six safety culture domains of the SAQ-OR. We also analysed changes in responses to two items regarding perioperative briefings. The SAQ-OR survey response rate was 80% (60/75) at baseline and 74% (53/72) one yr later. There were significant improvements in both the reported frequency (Pculture domain scores (Working Conditions, Perceptions of Management, Job Satisfaction, Safety Climate and Teamwork Climate) of the SAQ-OR (Pculture of elective orthopaedic operating theatres. © The Author 2015. Published by Oxford University Press on behalf of the British Journal of Anaesthesia. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  17. The nexus of nursing leadership and a culture of safer patient care.

    Science.gov (United States)

    Murray, Melanie; Sundin, Deborah; Cope, Vicki

    2018-03-01

    To explore the connection between +6 nursing leadership and enhanced patient safety. Critical reports from the Institute of Medicine in 1999 and Francis QC report of 2013 indicate that healthcare organisations, inclusive of nursing leadership, were remiss or inconsistent in fostering a culture of safety. The factors required to foster organisational safety culture include supportive leadership, effective communication, an orientation programme and ongoing training, appropriate staffing, open communication regarding errors, compliance to policy and procedure, and environmental safety and security. As nurses have the highest patient interaction, and leadership is discernible at all levels of nursing, nurse leaders are the nexus to influencing organisational culture towards safer practices. The position of this article was to explore the need to form a nexus between safety culture and leadership for the provision of safe care. Safety is crucial in health care for patient safety and patient outcomes. A culture of safety has been exposed as a major influence on patient safety practices, heavily influenced by leadership behaviours. The relationship between leadership and safety plays a pivotal role in creating positive safety outcomes for patient care. A safe culture is one nurtured by effective leadership. Patient safety is the responsibility of all healthcare workers, from the highest executive to the bedside nurse, thus effective leadership throughout all levels is essential in engaging staff to provide high quality care for the best possible patient outcomes. © 2017 John Wiley & Sons Ltd.

  18. Effects of additives on microstructures of titanate based nanotubes prepared by the hydrothermal process

    International Nuclear Information System (INIS)

    Kubo, Takashi; Sugimoto, Keijiro; Onoki, Takamasa; Nakahira, Atsushi; Yamasaki, Yuki

    2009-01-01

    Silica-containing TiO 2 -derived titanate nanotubes were prepared by the addition of a small amount of tetraethyl orthosilicate (TEOS) to TiO 2 -derived titanate nanotubes prepared by the hydrothermal process and a subsequent heat-treatment at 473 K in air. The microstructure and thermal behavior of synthesized silica containing TiO 2 -derived titanate nanotubes were investigated by various methods such as X-ray diffraction (XRD), X-ray absorption fine structure (XAF), and X-ray photoelectron spectroscopy (XPS). As a result, the addition of a small amount of TEOS leaded to the improvement of the thermal stability for TiO 2 -derived titanate nanotubes. XPS results revealed that Si was combined onto the surface of TiO 2 -derived titanate nanotubes, forming partial Si-O-Ti chemical bonds. Therefore, it was inferred that the thermal stability could be modified by forming partial Si-O-Ti chemical bonds at interface of silica and TiO 2 -derived titanate nanotubes. (author)

  19. Transformation of Beauveria bassiana to produce EGFP in Tenebrio molitor for use as animal feed additives.

    Science.gov (United States)

    Kim, Jae Su; Choi, Jae Young; Lee, Se Jin; Lee, Ju Hyun; Fu, Zhenli; Skinner, Margaret; Parker, Bruce L; Je, Yeon Ho

    2013-07-01

    Efforts are underway to develop more effective and safer animal feed additives. Entomopathogenic fungi can be considered practical expression platforms of functional genes within insects which have been used as animal feed additives. In this work, as a model, the enhanced green fluorescent protein (egfp) gene was expressed in yellow mealworms, Tenebrio molitor by highly infective Beauveria bassiana ERL1170. Among seven test isolates, ERL1170 treatment showed 57.1% and 98.3% mortality of mealworms 2 and 5 days after infection, respectively. The fungal transformation vector, pABeG containing the egfp gene, was inserted into the genomic DNA of ERL1170 using the restriction enzyme-mediated integration method. This resulted in the generation of the transformant, Bb-egfp#3, which showed the highest level of fluorescence. Bb-egfp#3-treated mealworms gradually turned dark brown, and in 7-days mealworm sections showed a strong fluorescence. This did not occur in the wild-type strain. This work suggests that further valuable proteins can be efficiently produced in this mealworm-based fungal expression platform, thereby increasing the value of mealworms in the animal feed additive industry. © 2013 Federation of European Microbiological Societies. Published by John Wiley & Sons Ltd. All rights reserved.

  20. Safer Roads: Comparisons Between Road Assessment Program and Composite Road Safety Index Method

    Directory of Open Access Journals (Sweden)

    Mohd Razelan Intan Suhana

    2017-01-01

    Full Text Available In most countries, crash statistics have becoming very crucial in evaluating road’s safety level. In Malaysia, these data are very important in deciding crash-prone areas known as black spot where specific road improvements plan will be proposed. However due to the unavailability of reliable crash data in many developing countries, appropriate road maintenance measures are facing great troubles. In light of that, several proactive methods in defining road’s safety level such as Road Assessment Program (RAP have emerged. This research aim to compare two proactive methods that have been tested in Malaysian roads ; road assessment program and road environment risk index which was developed based on composite index theory in defining road’s safety level. Composite road environment risk index was combining several crucial environment indicators, assigning weight and aggregating the individual index together to form a single value representing the road’s safety level. Based on the results, it can be concluded that both road assessment program and composite road environment risk index are contradicted in six different ways such as type of speed used, type of analysis used and their final outcomes. However, with an aim to promote safer roads, these two methods can be used concurrently as the outcomes in both methods seems to fulfil each other’s gap very well.

  1. Estimation of Spectral Exponent Parameter of 1/f Process in Additive White Background Noise

    Directory of Open Access Journals (Sweden)

    Semih Ergintav

    2007-01-01

    Full Text Available An extension to the wavelet-based method for the estimation of the spectral exponent, γ, in a 1/fγ process and in the presence of additive white noise is proposed. The approach is based on eliminating the effect of white noise by a simple difference operation constructed on the wavelet spectrum. The γ parameter is estimated as the slope of a linear function. It is shown by simulations that the proposed method gives reliable results. Global positioning system (GPS time-series noise is analyzed and the results provide experimental verification of the proposed method.

  2. Economic Analysis of Additive Manufacturing Integration in Injection Molding Process Chain

    DEFF Research Database (Denmark)

    Charalambis, Alessandro; Kerbache, Laoucine; Tosello, Guido

    The purpose of this research is to analyze how additive manufacturing can create value when it is utilized as a supportive technology to injection molding by quantifying the cost advantages that can be obtained. Tooling for the product development phase is investigated as pilot integration area...... of additive manufacturing with injection molding. Cost considerations are discussed through the development of a cost estimation model. The study shows that integration of additive manufacturing in the product development phase for fabrication of soft tooling is economically convenient with a cost reduction...... of 79,8% and 89,9%. The cost models on additive manufacturing have been built so far on the idea of substituting injection molding with additive manufacturing. In response to this literature gap, this research addresses the advantages of additive manufacturing utilized in a synergistic rather than...

  3. The effect of addition of selected carrageenans on viscoelastic properties of model processed cheese spreads

    Directory of Open Access Journals (Sweden)

    Michaela Černíková

    2007-01-01

    Full Text Available The effect of 0.25% w/w κ-carrageenan and ι‑carrageenan on viscoelastic properties of processed cheese were studied using model samples containing 40% w/w dry matter and 45 and 50% w/w fat in dry matter. Experimental samples of processed cheese were evaluated after 14 days of storage at the temperature of 6 ± 2 °C. Basic parameters of processed cheese samples under study (i.e. their dry matter content and pH were not different (P ≥ 0.05. There were no statistically significant differences in values of storage modulus G´ [Pa], loss modulus G'' [Pa] and tangent of phase shift angle tan δ [-] for the reference frequency of 1 Hz between processed cheese with κ‑carrageenan applied in the form of powder and in the form of aqueous dispersion (P ≥ 0.05. The addition of 0.25% w/w κ‑carrageenan and ι‑carrageenan (in the powder form resulted in an increase in storage (G´ and loss (G'' moduli and a decrease in values of tan δ (P < 0.05. As compared with control (i.e. without added carrageenans, samples of processed cheese became firmer. Iota-carrageenan added in the powder form in concentration of 0.25% w/w showed a more intensive effect on the increase in firmness of processed cheese under study than κ‑carrageenan (P < 0.05.

  4. Effects of nickel(II) addition on the activity of activated sludge microorganisms and activated sludge process

    International Nuclear Information System (INIS)

    Ong, Soon-An; Toorisaka, Eiichi; Hirata, Makoto; Hano, Tadashi

    2004-01-01

    The effects of Ni(II) in a synthetic wastewater on the activity of activated sludge microorganisms and sequencing batch reactor (SBR) treatment process were investigated. Two parallel lab-scale SBR systems were operated. One was used as a control unit, while the other received Ni(II) concentrations equal to 5 and 10 mg/l. The SBR systems were operated with FILL, REACT, SETTLE, DRAW and IDLE modes in the time ratio of 0.5:3.5:1.0:0.75:0.25 for a cycle time of 6 h. The addition of Ni(II) into SBR system caused drastically dropped in TOC removal rate (k) and specific oxygen uptake rate (SOUR) by activated sludge microorganisms due to the inhibitory effects of Ni(II) on the bioactivity of microorganisms. The addition of 5 mg/l Ni(II) caused a slight reduction in TOC removal efficiency, whereas 10 mg/l Ni(II) addition significantly affected the SBR performance in terms of suspended solids and TOC removal efficiency. Termination of Ni(II) addition led to almost full recovery of the bioactivity in microorganisms as shown in the increase of specific oxygen uptake rate (SOUR) and SBR treatment performance

  5. Silver Nanocube and Nanobar Growth via Anisotropic Monomer Addition and Particle Attachment Processes.

    Science.gov (United States)

    Xiao, Dongdong; Wu, Zhigang; Song, Miao; Chun, Jaehun; Schenter, Gregory K; Li, Dongsheng

    2018-01-30

    Understanding the growth mechanism of noble metal nanocrystals during solution synthesis is of significant importance for shape and property control. However, much remains unknown about the growth pathways of metal nanoparticles due to the lack of direct observation. Using an in situ transmission electron microscopy technique, we directly observed Ag nanocube and nanobar growth in an aqueous solution through both classical monomer-by-monomer addition and nonclassical particle attachment processes. During the particle attachment process, Ag nanocubes and nanobars were formed via both oriented and nonoriented attachment. Our calculations, along with the dynamics of the observed attachment, showed that the van der Waals force overcomes hydrodynamic and friction forces and drives the particles toward each other at separations of 10-100 nm in our experiments. During classical growth, anisotropic growth was also revealed, and the resulting unsymmetrical shape constituted an intermediate state for Ag nanocube growth. We hypothesized that the temporary symmetry breaking resulted from different growth rates on (001) surfaces due to a local surface concentration variation caused by the imbalance between the consumption of Ag + near the surface and the diffusion of Ag + from the bulk to the surface.

  6. Adolescents' and adults' perceptions of 'natural', 'organic' and 'additive-free' cigarettes, and the required disclaimers.

    Science.gov (United States)

    Byron, M Justin; Baig, Sabeeh A; Moracco, Kathryn E; Brewer, Noel T

    2016-09-01

    We sought to investigate adolescents' and adults' perceptions of an American Spirit advertisement with 'natural', 'organic' and 'additive-free' descriptors and related disclaimers. We conducted nine focus group discussions in the Southern USA, with 59 participants aged 13-64 years (30 male, 29 female), stratified by age, smoking status and susceptibility to smoking. We conducted thematic content analysis of the transcripts. Many participants were sceptical or confused about the 'natural', 'organic' and 'additive-free' descriptors. Many participants viewed American Spirit cigarettes as being less, or possibly less harmful than other cigarettes, even though the ad contained disclaimers explicitly stating that these cigarettes are not safer. Some participants said that people tend to ignore disclaimers, a few expressed doubt that the disclaimers were fully true, and others did not notice the disclaimers. A few smokers said they smoke American Spirit cigarettes because they think they are not as bad for them as other cigarettes. Disclaimers intended to prevent consumers from attributing a health benefit to cigarettes labelled as 'natural', 'additive-free', or 'organic' may be insufficient. A ban on these descriptors may be a more appropriate remedy than disclaimers. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  7. Synthesis and characterization of Ti-27.5Nb alloy made by CLAD® additive manufacturing process for biomedical applications

    International Nuclear Information System (INIS)

    Fischer, M.; Laheurte, P.; Acquier, P.; Joguet, D.; Peltier, L.; Petithory, T.; Anselme, K.; Mille, P.

    2017-01-01

    Biocompatible beta-titanium alloys such as Ti-27.5(at.%)Nb are good candidates for implantology and arthroplasty applications as their particular mechanical properties, including low Young's modulus, could significantly reduce the stress-shielding phenomenon usually occurring after surgery. The CLAD® process is a powder blown additive manufacturing process that allows the manufacture of patient specific (i.e. custom) implants. Thus, the use of Ti-27.5(at.%)Nb alloy formed by CLAD® process for biomedical applications as a mean to increase cytocompatibility and mechanical biocompatibility was investigated in this study. The microstructural properties of the CLAD-deposited alloy were studied with optical microscopy and electron back-scattered diffraction (EBSD) analysis. The conservation of the mechanical properties of the Ti-27.5Nb material after the transformation steps (ingot-powder atomisation-CLAD) were verified with tensile tests and appear to remain close to those of reference material. Cytocompatibility of the material and subsequent cell viability tests showed that no cytotoxic elements are released in the medium and that viable cells proliferated well. - Highlights: • Biomimetic implants can be provided from additive manufacturing with beta-titanium alloys. • We studied the properties of a Ti-Nb alloy elaborated with a laser deposition process. • TiNb alloy processed by LMD consists of only beta phase due to rapid cooling. • No preferential crystallographic texture is observed with EBSD analyses. • TiNb samples showed a combination of high strength and low Young's modulus.

  8. Synthesis and characterization of Ti-27.5Nb alloy made by CLAD® additive manufacturing process for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Fischer, M. [LEM3, Université de Lorraine, Ile du Saulcy, 57045 Metz (France); Laheurte, P., E-mail: pascal.laheurte@univ-lorraine.fr [LEM3, Université de Lorraine, Ile du Saulcy, 57045 Metz (France); Acquier, P. [IREPA Laser, Institut Carnot Mica, Parc d' Innovation, 67400 Illkirch (France); Joguet, D. [LERMPS, Université de Technologie de Belfort Montbéliard, Sevenans, 90010 Belfort (France); Peltier, L. [LEM3, Ecole Nationale Supérieure d' Arts et Métiers, 57078 Metz (France); Petithory, T.; Anselme, K. [IS2M, CNRS UMR7361, Université de Haute-Alsace, 68057 Mulhouse (France); Mille, P. [LGECO Institut National des Sciences Appliquées, 67000 Strasbourg (France)

    2017-06-01

    Biocompatible beta-titanium alloys such as Ti-27.5(at.%)Nb are good candidates for implantology and arthroplasty applications as their particular mechanical properties, including low Young's modulus, could significantly reduce the stress-shielding phenomenon usually occurring after surgery. The CLAD® process is a powder blown additive manufacturing process that allows the manufacture of patient specific (i.e. custom) implants. Thus, the use of Ti-27.5(at.%)Nb alloy formed by CLAD® process for biomedical applications as a mean to increase cytocompatibility and mechanical biocompatibility was investigated in this study. The microstructural properties of the CLAD-deposited alloy were studied with optical microscopy and electron back-scattered diffraction (EBSD) analysis. The conservation of the mechanical properties of the Ti-27.5Nb material after the transformation steps (ingot-powder atomisation-CLAD) were verified with tensile tests and appear to remain close to those of reference material. Cytocompatibility of the material and subsequent cell viability tests showed that no cytotoxic elements are released in the medium and that viable cells proliferated well. - Highlights: • Biomimetic implants can be provided from additive manufacturing with beta-titanium alloys. • We studied the properties of a Ti-Nb alloy elaborated with a laser deposition process. • TiNb alloy processed by LMD consists of only beta phase due to rapid cooling. • No preferential crystallographic texture is observed with EBSD analyses. • TiNb samples showed a combination of high strength and low Young's modulus.

  9. Impact of the rate of the additive process of forming a heavy structure deforming in creep on the development of its technological stresses

    Science.gov (United States)

    Parshin, Dmitry A.

    2018-05-01

    The additive process of forming a semicircular arched structure by means of layer-by-layer addition of material to its inner surface is simulated. The impact of this process running mode on the development of the technological stresses fields in the structure being formed under the action of gravity under properties of the material creep and aging is examined. In the framework of the linear mechanics of accreted solids a mathematical model of the process under study is offered and numerical experiments are conducted. It is shown that the stress-strain state of the additively formed heavy objects decisively depends on their formation mode. Various practically important trends and features of this dependence are studied.

  10. Predictive Simulation of Process Windows for Powder Bed Fusion Additive Manufacturing: Influence of the Powder Bulk Density.

    Science.gov (United States)

    Rausch, Alexander M; Küng, Vera E; Pobel, Christoph; Markl, Matthias; Körner, Carolin

    2017-09-22

    The resulting properties of parts fabricated by powder bed fusion additive manufacturing processes are determined by their porosity, local composition, and microstructure. The objective of this work is to examine the influence of the stochastic powder bed on the process window for dense parts by means of numerical simulation. The investigations demonstrate the unique capability of simulating macroscopic domains in the range of millimeters with a mesoscopic approach, which resolves the powder bed and the hydrodynamics of the melt pool. A simulated process window reveals the influence of the stochastic powder layer. The numerical results are verified with an experimental process window for selective electron beam-melted Ti-6Al-4V. Furthermore, the influence of the powder bulk density is investigated numerically. The simulations predict an increase in porosity and surface roughness for samples produced with lower powder bulk densities. Due to its higher probability for unfavorable powder arrangements, the process stability is also decreased. This shrinks the actual parameter range in a process window for producing dense parts.

  11. A Pilot Intervention to Promote Safer Sex in Heterosexual Puerto Rican Couples.

    Science.gov (United States)

    Pérez-Jiménez, David; Seal, David Wyatt; Ronis, David L

    2014-09-01

    Although the sexual transmission of HIV occurs in the context of an intimate relationship, preventive interventions with couples are scarce, particularly those designed for Hispanics. In this article, we present the effect of a pilot intervention directed to prevent HIV/AIDS in heterosexual couples in Puerto Rico. The intervention was theory-based and consisted of five three-hour group sessions. Primary goals included increasing male condom use and the practice of mutual masturbation as a safer sex method, and promoting favorable attitudes toward these behaviors. Twenty-six couples participated in this study. Fifteen were randomly assigned to the intervention group and eleven to a control group. Retention rates at post-intervention and follow-up were 82% for the whole sample. Results showed that there was a significant increase in the use of male condoms with main partners in the intervention group when compared with the control group. Couples in the intervention group also had better scores on secondary outcomes, such as attitudes toward condom use and mutual masturbation, HIV information, sexual decision-making, and social support. We found that these effects persisted over the three month follow up. A significant effect was also observed for the practice of mutual masturbation, but not for sexual negotiation. These results showed that promoting male condom use in dyadic interventions among heterosexual couples in Puerto Rico is feasible. Our findings suggest that because vaginal penetration has been constructed as the sexual script endpoint among many Hispanic couples, promoting other non-penetrative practices, such as mutual masturbation, may be difficult.

  12. Flow Characteristics of a Thermoset Fiber Composite Photopolymer Resin in a Vat Polymerization Additive Manufacturing Process

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Spangenberg, Jon; Pedersen, David B.

    Additive manufacturing vat polymerization has become a leading technology and gained a massive amount of attention in industrial applications such as injection molding inserts. By the use of the thermoset polymerization process inserts have increased their market share. For most industrial...... understood. Research indicates an orientation within the manufacturing layer and efforts have been made to achieve a more uniform orientation within the part. A vat polymerization machine consisting of a resin vat and a moving build plate has been simulated using the fluid flow module of Comsol Multiphysics...... photopolymer resin. The prediction can be used to identify potential clusters or misalignment of fibers and in the future allow for optimization of the machine design and manufacturing process....

  13. Thermographic process monitoring in powderbed based additive manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Krauss, Harald, E-mail: harald.krauss@iwb.tum.de; Zaeh, Michael F. [AMLab, iwb Application Center Augsburg, Technische Universität München (Germany); Zeugner, Thomas [Augsburg University (Germany)

    2015-03-31

    Selective Laser Melting is utilized to build metallic parts directly from CAD-Data by solidification of thin powder layers through application of a fast scanning laser beam. In this study layerwise monitoring of the temperature distribution is used to gather information about the process stability and the resulting part quality. The heat distribution varies with different kinds of parameters including scan vector length, laser power, layer thickness and inter-part distance in the job layout which in turn influence the resulting part quality. By integration of an off-axis mounted uncooled thermal detector the solidification as well as the layer deposition are monitored and evaluated. Errors in the generation of new powder layers usually result in a locally varying layer thickness that may cause poor part quality. For effect quantification, the locally applied layer thickness is determined by evaluating the heat-up of the newly deposited powder. During the solidification process space and time-resolved data is used to characterize the zone of elevated temperatures and to derive locally varying heat dissipation properties. Potential quality indicators are evaluated and correlated to the resulting part quality: Thermal diffusivity is derived from a simplified heat dissipation model and evaluated for every pixel and cool-down phase of a layer. This allows the quantification of expected material homogeneity properties. Maximum temperature and time above certain temperatures are measured in order to detect hot spots or delamination issues that may cause a process breakdown. Furthermore, a method for quantification of sputter activity is presented. Since high sputter activity indicates unstable melt dynamics this can be used to identify parameter drifts, improper atmospheric conditions or material binding errors. The resulting surface structure after solidification complicates temperature determination on the one hand but enables the detection of potential surface defects

  14. Most consumed processed foods by patients on hemodialysis: Alert for phosphate-containing additives and the phosphate-to-protein ratio.

    Science.gov (United States)

    Watanabe, Marcela T; Araujo, Raphael M; Vogt, Barbara P; Barretti, Pasqual; Caramori, Jacqueline C T

    2016-08-01

    Hyperphosphatemia is common in patients with chronic kidney disease (CKD) stages IV and V because of decreased phosphorus excretion. Phosphatemia is closely related to dietary intake. Thus, a better understanding of sources of dietary phosphate consumption, absorption and restriction, particularly inorganic phosphate found in food additives, is key to prevent consequences of this complication. Our aims were to investigate the most commonly consumed processed foods by patients with CKD on hemodialysis, to analyze phosphate and protein content of these foods using chemical analysis and to compare these processed foods with fresh foods. We performed a cross-sectional descriptive analytical study using food frequency questionnaires to rank the most consumed industrialized foods and beverages. Total phosphate content was determined by metavanadate colorimetry, and nitrogen content was determined by the Kjeldahl method. Protein amounts were estimated from nitrogen content. The phosphate-to-protein ratio (mg/g) was then calculated. Processed meat protein and phosphate content were compared with the nutritional composition of fresh foods using the Brazilian Food Composition Table. Phosphate measurement results were compared with data from the Food Composition Table - Support for Nutritional Decisions. An α level of 5% was considered significant. Food frequency questionnaires were performed on 100 patients (mean age, 59 ± 14 years; 57% male). Phosphate additives were mentioned on 70% of the product labels analyzed. Proteins with phosphate-containing additives provided approximately twice as much phosphate per gram of protein compared with that of fresh foods (p processed foods are higher than those of fresh foods, as well as phosphate-to-protein ratio. A better understanding of phosphate content in foods, particularly processed foods, may contribute to better control of phosphatemia in patients with CKD. Copyright © 2016 European Society for Clinical Nutrition and

  15. The effect of temperature and addition of reducing agent on sodium stannate preparation from cassiterite by the alkaline roasting process

    Science.gov (United States)

    Lalasari, Latifa Hanum; Andriyah, Lia; Arini, Tri; Firdiyono, F.

    2018-04-01

    Sodium stannate is an intermediate compound with the formula Na2SnO3. This compound is easily dissolved in water and has many applications in the electroplating industry, tin alloy production, and catalysts for organic synthesis. In this occasion was investigated the effect of temperature and the addition of reducing agent on making of sodium stannate phase from cassiterite by an alkaline roasting process using sodium carbonate (Na2CO3). Firstly, cassiterite was roasted at 700 °C for 3 hours and continued leaching process using 10% HCl solution at 110 °C for 2 hours. The cassiterite residue than was dried at 110 °C and mixed homogenously with a Na2CO3 decomposer at a mass ratio Na2CO3/cassiterite as 5:3 for the decomposition process. It was done by variation temperatures (300 °C, 700 °C, 800 °C, 870 °C, 900 °C) for 3 hours, variation times (3, 4, 5 hours) at a roasting temperature of 700 °C and addition of reducing agent such as sub-bituminous coal. The result of the experiment shows that cassiterite prepared by roasting and acid leaching process has the chemical composition as follows: 59.98% Sn, 22.58% O, 3.20% Ce, 3.15% La, 2.57% Nd, 1.67% Ti, 1.56% Fe, 1.24% P, 0.62% Ca and others. The Na2SnO3 phase begins to form at a roasting temperature of 870 °C for 3 hours. Although the roasting times was extended from 3 hours to 5 hours at 700 °C, the Na2SnO3 phase also has not yet formed. In other conditions, the addition of coal reducing agent to the roasting process would cause formations of Sn metal besides Na2SnO3 phase at 870 °C. At temperatures lower than 870 °C, the addition of coal only forms Sn metal, whereas the sodium stannate phase is not formed.

  16. Safer Prescribing and Care for the Elderly (SPACE): feasibility of audit and feedback plus practice mail-out to patients with high-risk prescribing.

    Science.gov (United States)

    Wallis, Katharine; Tuckey, Rebecca

    2017-06-01

    INTRODUCTION High-risk prescribing in general practice is common and places patients at increased risk of adverse events. AIM The Safer Prescribing and Care for the Elderly (SPACE) intervention, comprising audit and feedback plus practice mail-out to patients with high-risk prescribing, was designed to promote medicines review and support safer prescribing. This study aims to test the SPACE intervention feasibility in general practice. METHODS This feasibility study involved an Auckland Primary Health Organisation (PHO), a clinical advisory pharmacist, two purposively sampled urban general practices, and seven GPs. The acceptability and utility of the SPACE intervention were assessed by semi- structured interviews involving study participants, including 11 patients with high-risk prescribing. Interviews were audio-recorded, transcribed verbatim and analysed using a general inductive approach to identify emergent themes. RESULTS The pharmacist said the SPACE intervention facilitated communication with GPs, and provided a platform for their clinical advisory role at no extra cost to the PHO. GPs said the feedback session with the pharmacist was educational but added to time pressures. GPs selected 29 patients for the mail-out. Some GPs were concerned the mail-out might upset patients, but patients said they felt cared for. Some patients intended to take the letter to their next appointment and discuss their medicines with their GP; others said there were already many things to discuss and not enough time. Some patients were confused by the medicines information brochure. DISCUSSION The SPACE intervention is feasible in general practice. The medicines information brochure needs simplification. Further research is needed to test the effect of SPACE on high-risk prescribing.

  17. An Additive-Multiplicative Cox-Aalen Regression Model

    DEFF Research Database (Denmark)

    Scheike, Thomas H.; Zhang, Mei-Jie

    2002-01-01

    Aalen model; additive risk model; counting processes; Cox regression; survival analysis; time-varying effects......Aalen model; additive risk model; counting processes; Cox regression; survival analysis; time-varying effects...

  18. A rapid process of Yba2Cu3O7-δ thin film fabrication using trifluoroacetate metal-organic deposition with polyethylene glycol additive

    DEFF Research Database (Denmark)

    Wu, Wei; Feng, Feng; Shi, Kai

    2013-01-01

    Trifluoroacetate metal-organic deposition (TFA-MOD) is a promising technique to fabricate YBa2Cu3O7-δ (YBCO) superconducting films. However, its slow pyrolysis process, which usually takes more than 10 h, constitutes a barrier for industrial production. In this study, polyethylene glycol (PEG......) was utilized to reduce the stress generation inside the coated films when the strong pyrolysis reactions happen. With the addition of 30 wt% PEG2000 to the precursor solution, a smooth film surface could be obtained through a rapid pyrolysis process of 15 min. After the optimizations of the crystallization...... and oxygenation processes, mass percentage and molecular weight of PEG additive, YBCO thin films with Jc of about 4.5 MA cm-2 (77 K, self-field) could be routinely fabricated using (20-30) wt% PEG(1000-2000) additive with a total treatment time of about 2 h including the 15 min pyrolysis process time. The effects...

  19. Advanced Process Possibilities in Friction Crush Welding of Aluminum, Steel, and Copper by Using an Additional Wire

    Science.gov (United States)

    Besler, Florian A.; Grant, Richard J.; Schindele, Paul; Stegmüller, Michael J. R.

    2017-12-01

    Joining sheet metal can be problematic using traditional friction welding techniques. Friction crush welding (FCW) offers a high speed process which requires a simple edge preparation and can be applied to out-of-plane geometries. In this work, an implementation of FCW was employed using an additional wire to weld sheets of EN AW5754 H22, DC01, and Cu-DHP. The joint is formed by bringing together two sheet metal parts, introducing a wire into the weld zone and employing a rotating disk which is subject to an external force. The requirements of the welding preparation and the fundamental process variables are shown. Thermal measurements were taken which give evidence about the maximum temperature in the welding center and the temperature in the periphery of the sheet metals being joined. The high welding speed along with a relatively low heat input results in a minimal distortion of the sheet metal and marginal metallurgical changes in the parent material. In the steel specimens, this FCW implementation produces a fine grain microstructure, enhancing mechanical properties in the region of the weld. Aluminum and copper produced mean bond strengths of 77 and 69 pct to that of the parent material, respectively, whilst the steel demonstrated a strength of 98 pct. Using a wire offers the opportunity to use a higher-alloyed additional material and to precisely adjust the additional material volume appropriate for a given material alignment and thickness.

  20. Additive Manufacturing for Low Volume Bearings

    Energy Technology Data Exchange (ETDEWEB)

    Tate, John G. [Schaeffler Group USA, Spartanburg, SC (United States); Richardson, Bradley S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Love, Lonnie J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-09-01

    ORNL worked with the Schaeffler Group USA to explore additive manufacturing techniques that might be appropriate for prototyping of bearing cages. Multiple additive manufacturing techniques were investigated, including e-beam, binder jet and multiple laser based processes. The binder jet process worked best for the thin, detailed cages printed.

  1. Laser Additive Manufacturing of Magnetic Materials

    Science.gov (United States)

    Mikler, C. V.; Chaudhary, V.; Borkar, T.; Soni, V.; Jaeger, D.; Chen, X.; Contieri, R.; Ramanujan, R. V.; Banerjee, R.

    2017-03-01

    While laser additive manufacturing is becoming increasingly important in the context of next-generation manufacturing technologies, most current research efforts focus on optimizing process parameters for the processing of mature alloys for structural applications (primarily stainless steels, titanium base, and nickel base alloys) from pre-alloyed powder feedstocks to achieve properties superior to conventionally processed counterparts. However, laser additive manufacturing or processing can also be applied to functional materials. This article focuses on the use of directed energy deposition-based additive manufacturing technologies, such as the laser engineered net shaping (LENS™) process, to deposit magnetic alloys. Three case studies are presented: Fe-30 at.%Ni, permalloys of the type Ni-Fe-V and Ni-Fe-Mo, and Fe-Si-B-Cu-Nb (derived from Finemet) alloys. All these alloys have been processed from a blend of elemental powders used as the feedstock, and their resultant microstructures, phase formation, and magnetic properties are discussed in this paper. Although these alloys were produced from a blend of elemental powders, they exhibited relatively uniform microstructures and comparable magnetic properties to those of their conventionally processed counterparts.

  2. Textural characteristics of ready-to-eat breakfast cereals produced from different types of cereal and with varying water addition during extrusion process

    Directory of Open Access Journals (Sweden)

    Žaneta Ugarčić-Hardi

    2010-01-01

    Full Text Available Textural characteristics of ready-to-eat breakfast cereals were evaluated in order to determine the influence of wheat, corn and rice flour, as well as a varying water addition during the extrusion process. Extruded breakfast cereal balls were made of wheat semolina in combination with wheat, corn or rice flour. Three different levels of water addition (21 %, 23 % and 27 % were used during the extrusion process. Samples were prepared with and without surface sugar coating. Sensory and instrumental assessments (TA.XT Plus were used to evaluate textural attributes of dry samples and samples during immersion in milk. Weibull equation was used for nonlinear estimation of experimental data obtained for milk absorption and crispiness as a function of time. Crispiness of dry extruded balls without coating was much higher than for samples with coating. The highest values for crispness were observed for wheat extruded balls and the lowest for samples with corn flour addition. Increasing water addition during the extrusion process significantly increased crispness of ready-to-eat breakfast cereals. The rate of milk absorption and loss of crispiness were significantly higher for samples without coating than for samples with coating.

  3. Canned bluefin tuna, an in vitro cardioprotective functional food potentially safer than commercial fish oil based pharmaceutical formulations.

    Science.gov (United States)

    Tenore, Gian Carlo; Calabrese, Giorgio; Ritieni, Alberto; Campiglia, Pietro; Giannetti, Daniela; Novellino, Ettore

    2014-09-01

    Commercial canned fish species typical in the Italian market were evaluated for their lipid profile. Bluefin tuna samples showed the highest content in omega-3 fatty acids (n-3 PUFA) among the canned fish samples analyzed. Tests on H9C2 cardiomyocytes revealed that bluefin tuna n-3 PUFA may responsible for a significant cell protection against both physiological and doxorubicin-induced oxidative stress. Analogous tests performed by incubating cardiac cells with n-3 PUFA ethyl esters, of which most of fish oil pharmaceutical formulations (FOPF) are based, showed cytotoxicity at high doses. Our results highlighted that n-3 PUFA contents in a 50 g canned bluefin tuna portion would be almost equivalent to and potentially safer than those of 1 FOPF capsule (1000 mg)/die usually suggested for hyperlipidaemic subjects. Thus, Italian commercial canned bluefin tuna could be indicated as a functional food with potential health benefits for the prevention and care of cardiovascular disorders. Copyright © 2014 Elsevier Ltd. All rights reserved.

  4. The highway and railroad operating environments for hazardous shipments in the United States - safer in the '90s?

    International Nuclear Information System (INIS)

    Saricks, C.L.; Tompkins, M.M.

    2000-01-01

    This paper seeks to illuminate the status of transportation safety and risk for large-quantity shipments of spent commercial reactor fuel and mixed and hazardous wastes by examining road and rail accident and vehicular travel data from the mid-1990s. Of special interest are the effect of speed limit changes on controlled-access expressways (chiefly the Interstate Highway System) and the possible effect of season-to-season climatic variation on road transport. We found that improvements in railroad technology and infrastructure have created a safer overall operating environment for railroad freight shipments. We also found recent evidence of an increase in accident rates of heavy combination trucks in states that have raised highway speed limits. Finally, cold weather increases road transport risk, while conditions associated with higher ambient temperatures do not. This last finding is in contrast to rail transport, for which the literature associates both hot and cold temperature extremes with higher accident rates

  5. The Impact of Online Additional Reviews on Consumer's Purchase Process

    OpenAIRE

    Tiantian Shen; Qi Dai; Ran Wang; Qinglong Gou

    2015-01-01

    As the supplement of buyers' original reviews on products, online additional reviews were supported by some B2C websites recently. That is to say, consumers could post their recommendations or comments again in several months. This paper attempts to measure the impacts of additional reviews on consumers, as well as to investigate whether they are different from those of original ones. Our results not only indicate that purchasing intention, attitude certainty and after-sales service have sign...

  6. A ¤flexible additive multiplicative hazard model

    DEFF Research Database (Denmark)

    Martinussen, T.; Scheike, T. H.

    2002-01-01

    Aalen's additive model; Counting process; Cox regression; Hazard model; Proportional excess harzard model; Time-varying effect......Aalen's additive model; Counting process; Cox regression; Hazard model; Proportional excess harzard model; Time-varying effect...

  7. Effect of composition and processing conditions on selected characteristics of extruded corn instant gruels enriched with fruits addition

    Directory of Open Access Journals (Sweden)

    Kręcisz Magdalena

    2018-01-01

    Full Text Available Cranberries and goji berries were used as natural supplements in extruded instant corn gruels. The effects of additive type and level, as well as extrusion-cooking screw speed on selected properties of extrudates were tested. Corn grit was used as the base raw materials and dry and ground goji berries and cranberries were added at 1, 2, 3, 4 and 5%. Extrusion-cooking of blends was performed with a single screw extruder at temperature ranged 125-135°C using various screw speed during processing. Extrudates were ground below 1 mm for instant gruels. Water absorption, water solubility, as well as colour profile were tested. The results showed that the highest water absorption was evaluated for instant gruels consist the highest amount of goji berries extruded at the highest screw speed during processing, while cranberries addition have no significant effect on water absorption. Increasing amount of dry cranberries and goji berries in the recipe affected on lowering the water solubility of the extrudates. Significant effect of fruits on color coordinates was observed. Increasing amount of dry berries lowered lightness L* and yellowness of instant gruels, especially when goji berries were used in the recipe. Increasing the screw speed during processing decreased intensity b* values.

  8. EFFECT OF CHICKEN BONE-MARROW ADDITION TO BREAST AND LEG MEAT SUBJECTED TO DIFFERENT GRINDING PROCESSES

    OpenAIRE

    POLLONIO, MAR; ANTUNES, AJ

    1993-01-01

    Mechanical deboning makes chicken meat highly suscetible to lipid oxidation. Tissue disruption and the incorporation of unknown amounts of bone marrow are among the main factors involved. This research was undertaken to evaluate the effect of chicken bone marrow addition to breast and leg meat, ground in a regular meat grinder and passed through a mechanical deboner on lipid stability during frozen storage at -18-degrees-C. Breast and leg meat were manually deboned: a portion was processed th...

  9. Biosafety and Biosecurity: A Relative Risk-Based Framework for Safer, More Secure, and Sustainable Laboratory Capacity Building.

    Science.gov (United States)

    Dickmann, Petra; Sheeley, Heather; Lightfoot, Nigel

    2015-01-01

    Laboratory capacity building is characterized by a paradox between endemicity and resources: countries with high endemicity of pathogenic agents often have low and intermittent resources (water, electricity) and capacities (laboratories, trained staff, adequate regulations). Meanwhile, countries with low endemicity of pathogenic agents often have high-containment facilities with costly infrastructure and maintenance governed by regulations. The common practice of exporting high biocontainment facilities and standards is not sustainable and concerns about biosafety and biosecurity require careful consideration. A group at Chatham House developed a draft conceptual framework for safer, more secure, and sustainable laboratory capacity building. The draft generic framework is guided by the phrase "LOCAL - PEOPLE - MAKE SENSE" that represents three major principles: capacity building according to local needs (local) with an emphasis on relationship and trust building (people) and continuous outcome and impact measurement (make sense). This draft generic framework can serve as a blueprint for international policy decision-making on improving biosafety and biosecurity in laboratory capacity building, but requires more testing and detailing development.

  10. Biosafety and Biosecurity: A relative risk-based framework for safer, more secure and sustainable laboratory capacity building

    Directory of Open Access Journals (Sweden)

    Petra eDickmann

    2015-10-01

    Full Text Available Background: Laboratory capacity building is characterized by a paradox between endemicity and resources: Countries with high endemicity of pathogenic agents often have low and intermittent resources (water, electricity and capacities (laboratories, trained staff, adequate regulations. Meanwhile, countries with low endemicity of pathogenic agents often have high containment facilities with costly infrastructure and maintenance governed by regulations. The common practice of exporting high biocontainment facilities and standards is not sustainable and concerns about biosafety and biosecurity require careful consideration. Methods: A group at Chatham House developed a draft conceptual framework for safer, more secure and sustainable laboratory capacity building. Results: The draft generic framework is guided by the phrase ‘LOCAL – PEOPLE – MAKE SENSE’ that represents three major principles: capacity building according to local needs (local with an emphasis on relationship and trust-building (people and continuous outcome and impact measurement (make sense. Conclusions: This draft generic framework can serve as a blueprint for international policy decision-making on improving biosafety and biosecurity in laboratory capacity building, but requires more testing and detailing development.

  11. Homelessness among a cohort of women in street-based sex work: the need for safer environment interventions

    Directory of Open Access Journals (Sweden)

    Gibson Kate

    2011-08-01

    Full Text Available Abstract Background Drawing on data from a community-based prospective cohort study in Vancouver, Canada, we examined the prevalence and individual, interpersonal and work environment correlates of homelessness among 252 women in street-based sex work. Methods Bivariate and multivariate logistic regression using generalized estimating equations (GEE was used to examine the individual, interpersonal and work environment factors that were associated with homelessness among street-based sex workers. Results Among 252 women, 43.3% reported homelessness over an 18-month follow-up period. In the multivariable GEE logistic regression analysis, younger age (adjusted odds ratio [aOR] = 0.93; 95%confidence interval [95%CI] 0.93-0.98, sexual violence by non-commercial partners (aOR = 2.14; 95%CI 1.06-4.34, servicing a higher number of clients (10+ per week vs Conclusions These findings indicate a critical need for safer environment interventions that mitigate the social and physical risks faced by homeless FSWs and increase access to safe, secure housing for women.

  12. Female gratification, sexual power and safer sex: female sexuality as an empowering resource among women in Rwanda.

    Science.gov (United States)

    Skafte, Ina; Silberschmidt, Margrethe

    2014-01-01

    The gender-based response to HIV in sub-Saharan Africa has tended to reinforce normative stereotypes of women as subordinated, passive and powerless victims, in particular in sexual relations. However, based on qualitative data from Rwanda, this paper argues that such conceptualisations fail to recognise that while women do comply with prevalent social norms, they also challenge these norms and sex becomes a domain in which they can exert power. Female sexuality and sexual gratification - acknowledged and valued by women as well as men - play a pivotal role in the Rwandese mode of sexual intercourse. This provides women a central position in sexual relations, which affords them sexual power. Recognising their sexuality as a resource and drawing upon this 'sexual capital', women are active social agents who have the capacity to manipulate and challenge male dominance in a deliberate strategy both to practice safer sex and to access decision-making power and material resources. This suggests that inherent in sexual relations is a potential for the empowerment of women and the transformation of gender relations.

  13. A generalized additive regression model for survival times

    DEFF Research Database (Denmark)

    Scheike, Thomas H.

    2001-01-01

    Additive Aalen model; counting process; disability model; illness-death model; generalized additive models; multiple time-scales; non-parametric estimation; survival data; varying-coefficient models......Additive Aalen model; counting process; disability model; illness-death model; generalized additive models; multiple time-scales; non-parametric estimation; survival data; varying-coefficient models...

  14. Additive functionals and excursions of Kuznetsov processes

    Directory of Open Access Journals (Sweden)

    Hacène Boutabia

    2005-01-01

    semigroup of transition. In this paper, we give the excursion laws of (Xtt∈ℝ+ conditioned on the strict past and future without duality hypothesis. We study excursions of a general regenerative system and of a regenerative system consisting of the closure of the set of times the regular points of B are visited. In both cases, those conditioned excursion laws depend only on two points Xg− and Xd, where ]g,d[ is an excursion interval of the regenerative set M. We use the (FDt-predictable exit system to bring together the isolated points of M and its perfect part and replace the classical optional exit system. This has been a subject in literature before (e.g., Kaspi (1988 under the classical duality hypothesis. We define an “additive functional” for (Ytt∈ℝ with B, we generalize the laws cited before to (Ytt∈ℝ, and we express laws of pairs of excursions.

  15. Rotor-stator spinning disc reactor

    NARCIS (Netherlands)

    Meeuwse, M.

    2011-01-01

    The chemical industry is continuously working to make the production more efficient and safer. Process intensification is the trend in which new equipment and processing methods are developed, which require less energy, are safer and produce less waste products. The main improvements can be made by

  16. Biomass ash reutilisation as an additive in the composting process of organic fraction of municipal solid waste.

    Science.gov (United States)

    Asquer, Carla; Cappai, Giovanna; De Gioannis, Giorgia; Muntoni, Aldo; Piredda, Martina; Spiga, Daniela

    2017-11-01

    In this work the effects of selected types of biomass ash on the composting process and final product quality were studied by conducting a 96-day long experiment where the source separated organic fraction of municipal waste, mixed with wood prunings that served as bulking agent, was added with 0%, 2%, 4% and 8% wt/wt of biomass ash. The evolution over time of the main process parameters was observed, and the final composts were characterised. On the basis of the results, both the composting process and the quality of the final product were improved by ash addition. Enhanced volatile solids reduction and biological stability (up to 32% and 52%, respectively, as compared to the unamended product) were attained when ash was added, since ash favored the aerobic degradation by acting asa physical conditioner. In the final products, higher humification of organic matter (expressed in terms of the humification index, that was 2.25 times higher in the most-enriched compost than in the unamended one) and total Ca, K, Mg and P content were observed when ash was used. The latter aspect may influence the composts marketability positively, particularly with regards to potassium and phosphorus. The heavy metals content, that is regarded as the main environmental disadvantage when using ash asa composting additive, did not negatively affect the final composts quality. However, some other controversial effects of ash, related to the moisture and temperature values attained during the process, pH (8.8-9.2 as compared to 8.2 of the unamended compost) and electrical conductivity levels (up to 53% higher as compared to the unamended compost) in the final composts, were also observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Impact of particle size, thermal processing, fat inclusion, and moisture addition on starch gelatinization of broiler feeds

    Directory of Open Access Journals (Sweden)

    K Muramatsu

    2014-12-01

    Full Text Available The present study evaluated the effect of feed particle size, thermal processing different levels of fat inclusion and of moisture addition on the amount of gelatinized starch in a corn-soybean broiler diet. The different processing factors were combined in a 2 x 4 x 4 x 2 factorial arrangement in a three randomized block design consisting of three production series: two particle sizes (coarse: 1041 microns and medium: 743 microns, four fat inclusion levels at the mixer (15, 25, 35, and 45 g/kg of feed, four moisture addition levels in the conditioner (0, 7, 14, and 21g/kg of feed, and two thermal processing treatments (conditioning-pelleting or conditioning-expanding-pelleting which resulted in 64 different processed feeds. For the determination of the amount of gelatinized starch one feed sample was collected per treatment in each of three production series, totaling three replicates/treatment. Data were transformed using a variation of Box-Cox transformation in order to fit normal distribution (p>0.05. Adding moisture up to 21g/kg of feed in the conditioner linearly increased the amount of gelatinized starch (p<0.05. The conditioner-expander-pelleting treatment of the diets (at 110°C increased (p<0.05 the degree of starch gelatinization from 32.0 to 35.3 % compared with the conditioner-pelleting treatment (at 80-82°C. The gelatinized starch content increased from 30.2 to 37.2% in the feed (p<0.05 as the particle size increased from medium to coarse. Fat inclusion had a quadratic effect (p<0.05 on starch gelatinization. The degree of starch gelatinization was significantly reduced with fat inclusion levels higher than 35 g/kg of diet. The factors evaluated in this study resulted in interactions and significant effects on degree of starch gelatinization.

  18. Advanced Material Strategies for Next-Generation Additive Manufacturing.

    Science.gov (United States)

    Chang, Jinke; He, Jiankang; Mao, Mao; Zhou, Wenxing; Lei, Qi; Li, Xiao; Li, Dichen; Chua, Chee-Kai; Zhao, Xin

    2018-01-22

    Additive manufacturing (AM) has drawn tremendous attention in various fields. In recent years, great efforts have been made to develop novel additive manufacturing processes such as micro-/nano-scale 3D printing, bioprinting, and 4D printing for the fabrication of complex 3D structures with high resolution, living components, and multimaterials. The development of advanced functional materials is important for the implementation of these novel additive manufacturing processes. Here, a state-of-the-art review on advanced material strategies for novel additive manufacturing processes is provided, mainly including conductive materials, biomaterials, and smart materials. The advantages, limitations, and future perspectives of these materials for additive manufacturing are discussed. It is believed that the innovations of material strategies in parallel with the evolution of additive manufacturing processes will provide numerous possibilities for the fabrication of complex smart constructs with multiple functions, which will significantly widen the application fields of next-generation additive manufacturing.

  19. Advanced Material Strategies for Next-Generation Additive Manufacturing

    Directory of Open Access Journals (Sweden)

    Jinke Chang

    2018-01-01

    Full Text Available Additive manufacturing (AM has drawn tremendous attention in various fields. In recent years, great efforts have been made to develop novel additive manufacturing processes such as micro-/nano-scale 3D printing, bioprinting, and 4D printing for the fabrication of complex 3D structures with high resolution, living components, and multimaterials. The development of advanced functional materials is important for the implementation of these novel additive manufacturing processes. Here, a state-of-the-art review on advanced material strategies for novel additive manufacturing processes is provided, mainly including conductive materials, biomaterials, and smart materials. The advantages, limitations, and future perspectives of these materials for additive manufacturing are discussed. It is believed that the innovations of material strategies in parallel with the evolution of additive manufacturing processes will provide numerous possibilities for the fabrication of complex smart constructs with multiple functions, which will significantly widen the application fields of next-generation additive manufacturing.

  20. Advanced Material Strategies for Next-Generation Additive Manufacturing

    Science.gov (United States)

    Chang, Jinke; He, Jiankang; Zhou, Wenxing; Lei, Qi; Li, Xiao; Li, Dichen

    2018-01-01

    Additive manufacturing (AM) has drawn tremendous attention in various fields. In recent years, great efforts have been made to develop novel additive manufacturing processes such as micro-/nano-scale 3D printing, bioprinting, and 4D printing for the fabrication of complex 3D structures with high resolution, living components, and multimaterials. The development of advanced functional materials is important for the implementation of these novel additive manufacturing processes. Here, a state-of-the-art review on advanced material strategies for novel additive manufacturing processes is provided, mainly including conductive materials, biomaterials, and smart materials. The advantages, limitations, and future perspectives of these materials for additive manufacturing are discussed. It is believed that the innovations of material strategies in parallel with the evolution of additive manufacturing processes will provide numerous possibilities for the fabrication of complex smart constructs with multiple functions, which will significantly widen the application fields of next-generation additive manufacturing. PMID:29361754

  1. Enhancing the performance of model-based elastography by incorporating additional a priori information in the modulus image reconstruction process

    International Nuclear Information System (INIS)

    Doyley, Marvin M; Srinivasan, Seshadri; Dimidenko, Eugene; Soni, Nirmal; Ophir, Jonathan

    2006-01-01

    Model-based elastography is fraught with problems owing to the ill-posed nature of the inverse elasticity problem. To overcome this limitation, we have recently developed a novel inversion scheme that incorporates a priori information concerning the mechanical properties of the underlying tissue structures, and the variance incurred during displacement estimation in the modulus image reconstruction process. The information was procured by employing standard strain imaging methodology, and introduced in the reconstruction process through the generalized Tikhonov approach. In this paper, we report the results of experiments conducted on gelatin phantoms to evaluate the performance of modulus elastograms computed with the generalized Tikhonov (GTK) estimation criterion relative to those computed by employing the un-weighted least-squares estimation criterion, the weighted least-squares estimation criterion and the standard Tikhonov method (i.e., the generalized Tikhonov method with no modulus prior). The results indicate that modulus elastograms computed with the generalized Tikhonov approach had superior elastographic contrast discrimination and contrast recovery. In addition, image reconstruction was more resilient to structural decorrelation noise when additional constraints were imposed on the reconstruction process through the GTK method

  2. Additive genetic variance in polyandry enables its evolution, but polyandry is unlikely to evolve through sexy or good sperm processes.

    Science.gov (United States)

    Travers, L M; Simmons, L W; Garcia-Gonzalez, F

    2016-05-01

    Polyandry is widespread despite its costs. The sexually selected sperm hypotheses ('sexy' and 'good' sperm) posit that sperm competition plays a role in the evolution of polyandry. Two poorly studied assumptions of these hypotheses are the presence of additive genetic variance in polyandry and sperm competitiveness. Using a quantitative genetic breeding design in a natural population of Drosophila melanogaster, we first established the potential for polyandry to respond to selection. We then investigated whether polyandry can evolve through sexually selected sperm processes. We measured lifetime polyandry and offensive sperm competitiveness (P2 ) while controlling for sampling variance due to male × male × female interactions. We also measured additive genetic variance in egg-to-adult viability and controlled for its effect on P2 estimates. Female lifetime polyandry showed significant and substantial additive genetic variance and evolvability. In contrast, we found little genetic variance or evolvability in P2 or egg-to-adult viability. Additive genetic variance in polyandry highlights its potential to respond to selection. However, the low levels of genetic variance in sperm competitiveness suggest that the evolution of polyandry may not be driven by sexy sperm or good sperm processes. © 2016 European Society For Evolutionary Biology. Journal of Evolutionary Biology © 2016 European Society For Evolutionary Biology.

  3. NATURAL ANTIMICROBIAL AGENT USE IN THE PRESERVATION OF FRUITS AND VEGETABLES

    Directory of Open Access Journals (Sweden)

    Elvia Nereyda Rodríguez Sauceda

    2011-01-01

    Full Text Available Today has been a need to find alternatives of conservation, because it has been associated with consumption of poison chemical preservatives. The demand for minimally processed fresh products is increasing, and interest in natural antimicrobial agents (derived from plants, so now looking for the combination of two or more factors that interact additively or synergistically controlling population microbial, allowing it to fresh produce similar products with less additives, it should be noted that the rate of microbial spoilage depends not only on microorganisms but also the chemical combination of product and type of initial microbial load. That is why the main aim of food processing is to provide comfort to humans through a safe, nutritionally adequate and meet the expectations of taste, aroma and appearance, so the use of natural food additives involves the isolation, purification, stabilization and incorporation of these compounds to food antimicrobial purposes, without adversely affecting the sensory characteristics. In general, every time we discover more plants or parts thereof which contain natural antimicrobials, such as including phenolic compounds from bark, stems, leaves, flowers, organic acids present in fruits and phytoalexins produced in plants, so as will not only safer, but better food quality and type of antimicrobials that are regarded as potentially safer sources.

  4. Early process development of API applied to poorly water-soluble TBID.

    Science.gov (United States)

    Meise, Marius; Niggemann, Matthias; Dunens, Alexandra; Schoenitz, Martin; Kuschnerow, Jan C; Kunick, Conrad; Scholl, Stephan

    2018-05-01

    Finding and optimising of synthesis processes for active pharmaceutical ingredients (API) is time consuming. In the finding phase, established methods for synthesis, purification and formulation are used to achieve a high purity API for biological studies. For promising API candidates, this is followed by pre-clinical and clinical studies requiring sufficient quantities of the active component. Ideally, these should be produced with a process representative for a later production process and suitable for scaling to production capacity. This work presents an overview of different approaches for process synthesis based on an existing lab protocol. This is demonstrated for the production of the model drug 4,5,6,7-tetrabromo-2-(1H-imidazol-2-yl) isoindolin-1,3-dione (TBID). Early batch synthesis and purification procedures typically suffer from low and fluctuating yields and purities due to poor process control. In a first step the literature synthesis and purification procedure was modified and optimized using solubility measurements, targeting easier and safer processing for consecutive studies. Copyright © 2018 Elsevier B.V. All rights reserved.

  5. Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

    Energy Technology Data Exchange (ETDEWEB)

    TOMASZEWSKI, T.A.

    2000-04-25

    The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management.

  6. Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

    International Nuclear Information System (INIS)

    TOMASZEWSKI, T.A.

    2000-01-01

    The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management

  7. Additive manufactured serialization

    Science.gov (United States)

    Bobbitt, III, John T.

    2017-04-18

    Methods for forming an identifying mark in a structure are described. The method is used in conjunction with an additive manufacturing method and includes the alteration of a process parameter during the manufacturing process. The method can form in a unique identifying mark within or on the surface of a structure that is virtually impossible to be replicated. Methods can provide a high level of confidence that the identifying mark will remain unaltered on the formed structure.

  8. Message framing and defensive processing: a cultural examination.

    Science.gov (United States)

    Ko, Deborah M; Kim, Heejung S

    2010-01-01

    Past research has shown that health messages on safer sexual practices that focus on relational consequences are more persuasive than messages that focus on personal consequences. However, we theorize that it is defensiveness against personal risk framing that threatens the self among people from more individualistic cultures. Two studies tested this idea. Study 1 showed that European Americans were less persuaded by personal framing than by relational framing but that this pattern was not found for Asian Americans, who are more collectivistic. Study 2 showed that these defensive patterns were eliminated among European American participants when a person's self-image was affirmed. These results suggest defensive processes as the mechanism behind the differences in message framing effectiveness and motivate a closer look at cultural patterns.

  9. Effects of plasma electrolytic oxidation process on the mechanical properties of additively manufactured porous biomaterials.

    Science.gov (United States)

    Gorgin Karaji, Zahra; Hedayati, Reza; Pouran, Behdad; Apachitei, Iulian; Zadpoor, Amir A

    2017-07-01

    Metallic porous biomaterials are recently attracting more attention thanks to the additive manufacturing techniques which help produce more complex structures as compared to conventional techniques. On the other hand, bio-functional surfaces on metallic biomaterials such as titanium and its alloys are necessary to enhance the biological interactions with the host tissue. This study discusses the effect of plasma electrolytic oxidation (PEO), as a surface modification technique to produce bio-functional layers, on the mechanical properties of additively manufactured Ti6Al4V scaffolds based on the cubic unit cell. For this purpose, the PEO process with two different oxidation times was applied on scaffolds with four different values of relative density. The effects of the PEO process were studied by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), optical microscopy as well as static and dynamic (fatigue) mechanical testing under compression. SEM results indicated pore formation on the surface of the scaffolds after oxidation with a thickness of 4.85±0.36μm of the oxide layer after 2min and 9.04±2.27μm after 5min oxidation (based on optical images). The static test results showed the high effect of relative density of porous structure on its mechanical properties. However, oxidation did not influence most of the mechanical properties such as maximum stress, yield stress, plateau stress, and energy absorption, although its effect on the elastic modulus was considerable. Under fatigue loading, none of the scaffolds failed even after 10 6 loading cycles at 70% of their yield stress. Copyright © 2017 Elsevier B.V. All rights reserved.

  10. Additive manufacturing of metals

    International Nuclear Information System (INIS)

    Herzog, Dirk; Seyda, Vanessa; Wycisk, Eric; Emmelmann, Claus

    2016-01-01

    Additive Manufacturing (AM), the layer-by layer build-up of parts, has lately become an option for serial production. Today, several metallic materials including the important engineering materials steel, aluminium and titanium may be processed to full dense parts with outstanding properties. In this context, the present overview article describes the complex relationship between AM processes, microstructure and resulting properties for metals. It explains the fundamentals of Laser Beam Melting, Electron Beam Melting and Laser Metal Deposition, and introduces the commercially available materials for the different processes. Thereafter, typical microstructures for additively manufactured steel, aluminium and titanium are presented. Special attention is paid to AM specific grain structures, resulting from the complex thermal cycle and high cooling rates. The properties evolving as a consequence of the microstructure are elaborated under static and dynamic loading. According to these properties, typical applications are presented for the materials and methods for conclusion.

  11. Prediction of the Fiber Orientation State and the Resulting Structural and Thermal Properties of Fiber Reinforced Additive Manufactured Composites Fabricated Using the Big Area Additive Manufacturing Process

    Directory of Open Access Journals (Sweden)

    Timothy Russell

    2018-04-01

    Full Text Available Recent advances in Fused Filament Fabrication (FFF include large material deposition rates and the addition of chopped carbon fibers to the filament feedstock. During processing, the flow field within the polymer melt orients the fiber suspension, which is important to quantify as the underlying fiber orientation influences the mechanical and thermal properties. This paper investigates the correlation between processing conditions and the resulting locally varying thermal-structural properties that dictate both the final part performance and part dimensionality. The flow domain includes both the confined and unconfined flow indicative of the extruder nozzle within the FFF deposition process. The resulting orientation is obtained through two different isotropic rotary diffusion models, the model by Folgar and Tucker and that of Wang et al., and a comparison is made to demonstrate the sensitivity of the deposited bead’s spatially varying orientation as well as the final processed part’s thermal-structural performance. The results indicate the sensitivity of the final part behavior is quite sensitive to the choice of the slowness parameter in the Wang et al. model. Results also show the need, albeit less than that of the choice of fiber interaction model, to include the extrudate swell and deposition within the flow domain.

  12. Effect of granular activated carbon addition on the effluent properties and fouling potentials of membrane-coupled expanded granular sludge bed process.

    Science.gov (United States)

    Ding, An; Liang, Heng; Qu, Fangshu; Bai, Langming; Li, Guibai; Ngo, Huu Hao; Guo, Wenshan

    2014-11-01

    To mitigate membrane fouling of membrane-coupled anaerobic process, granular activated carbon (GAC: 50 g/L) was added into an expanded granular sludge bed (EGSB). A short-term ultrafiltration test was investigated for analyzing membrane fouling potential and underlying fouling mechanisms. The results showed that adding GAC into the EGSB not only improved the COD removal efficiency, but also alleviated membrane fouling efficiently because GAC could help to reduce soluble microbial products, polysaccharides and proteins by 26.8%, 27.8% and 24.7%, respectively, compared with the control system. Furthermore, excitation emission matrix (EEM) fluorescence spectroscopy analysis revealed that GAC addition mainly reduced tryptophan protein-like, aromatic protein-like and fulvic-like substances. In addition, the resistance distribution analysis demonstrated that adding GAC primarily decreased the cake layer resistance by 53.5%. The classic filtration mode analysis showed that cake filtration was the major fouling mechanism for membrane-coupled EGSB process regardless of the GAC addition. Copyright © 2014 Elsevier Ltd. All rights reserved.

  13. CFD model of laser additive manufacturing process of cylinders

    CSIR Research Space (South Africa)

    Tamsaout, T

    2017-11-01

    Full Text Available of the molten pool. An important accumulation of heat in the already deposited part during the filling stage was observed, which can be attributed to the continuous nature of the process. Finally, the calculations of thermal cycles and heating/cooling rates...-axial powder supply are the controlled heating of the powder before it enters the melt pool, and higher powder efficiency [1], [2], [3]. In this process, a laser beam is directed on to a metallic substrate surface to create a moving melt pool and, using a co...

  14. Additional methods for the processing of solid radioactive wastes

    International Nuclear Information System (INIS)

    Tittlova, E.; Svrcek, A.; Hazucha, E. at el.

    1989-01-01

    An account is given of the work performed within the A 01-159-812/05 State Project concerned with the technology of and technical means for the processing of solid wastes arising during the operation of nuclear power plants. This included the development of the incineration equipment, development of the process of air filter disposal and equipment therefor, manufacture of a saw for fragmentation of wood, manufacture of a sorting box, ultimate solution of the problem of waste sorting, and use of high-pressure compression technology. (author). 1 tab., 9 refs

  15. Water properties and structure of pork sausages as affected by high-pressure processing and addition of carrot fibre

    DEFF Research Database (Denmark)

    Møller, Sandie Mejer; Grossi, Alberto Blak; Christensen, Mette

    2011-01-01

    The effects of high-pressure processing (HPP) and addition of carrot fibre on pork sausages have been studied using NMR T(2) relaxometry and measurements of water-binding capacity (WBC) by centrifugation. Significant effects of temperature (raw, 40, 50, or 60°C), holding time (1s, 3, 6, or 9min......), and addition of carrot fibre on the distribution and mobility of water were found. However, the effect of carrot fibre could not be explained by structural changes in the sausages when examined by confocal laser scanning microscopy (CLSM). Correlations between T(2) relaxation measurements and WBC determined...... by centrifugation revealed that T(2) relaxation times were able to explain more than 90% of the variation in WBC for both non-pressure and pressure-treated sausages. However, only 49% of the variation was explained for pressure-treated sausages with carrot fibre, indicating that combining addition of fibre and high...

  16. Structural-Health Aware Failure-Tolerant Engineered to Respond (SAFER) Additively Manufactured Systems, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Structural degradation and failure can cause malfunctions and long-term problems aboard spacecraft, jeopardizing the crew, especially in deep space missions. On...

  17. IMPACTS OF ANTIFOAM ADDITIONS AND ARGON BUBBLING ON DEFENSE WASTE PROCESSING FACILITY REDUCTION/OXIDATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C.; Johnson, F.

    2012-06-05

    During melting of HLW glass, the REDOX of the melt pool cannot be measured. Therefore, the Fe{sup +2}/{Sigma}Fe ratio in the glass poured from the melter must be related to melter feed organic and oxidant concentrations to ensure production of a high quality glass without impacting production rate (e.g., foaming) or melter life (e.g., metal formation and accumulation). A production facility such as the Defense Waste Processing Facility (DWPF) cannot wait until the melt or waste glass has been made to assess its acceptability, since by then no further changes to the glass composition and acceptability are possible. therefore, the acceptability decision is made on the upstream process, rather than on the downstream melt or glass product. That is, it is based on 'feed foward' statistical process control (SPC) rather than statistical quality control (SQC). In SPC, the feed composition to the melter is controlled prior to vitrification. Use of the DWPF REDOX model has controlled the balanjce of feed reductants and oxidants in the Sludge Receipt and Adjustment Tank (SRAT). Once the alkali/alkaline earth salts (both reduced and oxidized) are formed during reflux in the SRAT, the REDOX can only change if (1) additional reductants or oxidants are added to the SRAT, the Slurry Mix Evaporator (SME), or the Melter Feed Tank (MFT) or (2) if the melt pool is bubble dwith an oxidizing gas or sparging gas that imposes a different REDOX target than the chemical balance set during reflux in the SRAT.

  18. Retardation of the dewetting process due to the addition of functional copolymers at polymer-polymer interfaces

    CERN Document Server

    Wunnicke, O; Lorenz-Haas, C; Leiner, V

    2002-01-01

    We studied the retardation of the dewetting process due to the addition of a functional copolymer in a polymer bilayer film. The model system consists of fully deuterated polystyrene (PS-d) on top of an amorphous polyamide (PA) sublayer on silicon substrates. Bilayer films were prepared with different content (0, 5, 10 and 30 vol. %) of a statistical copolymer (protonated styrene maleic anhydride acid (SMA2) containing 2% MA groups along the chain) being capable of forming hydrogen bonds with PA. The as-prepared as well as the annealed samples were investigated by neutron-reflectivity (NR) experiments, scanning force microscopy and optical microscopy. A significant retardation of dewetting is observed with the addition of SMA2. From model fits of NR curves the scattering length density profiles perpendicular to the sample surface were determined and an enrichment layer of SMA2 is detected. Retardation is explained by the intermixing of SMA2 and PS-d at the interface. (orig.)

  19. How Safe Are Color Additives?

    Science.gov (United States)

    ... Linkedin Pin it Email Print Subscribe: FDA Consumer Health Information Color additives give the red tint to your fruit punch ... in Foods, Drugs, Cosmetics, and Medical Devices Color Additives: FDA's Regulatory Process and Historical Perspectives ... Health Cosmetics Dietary Supplements Drugs Food Medical Devices Nutrition ...

  20. Laser-based additive manufacturing of metals

    CSIR Research Space (South Africa)

    Kumar, S

    2010-11-01

    Full Text Available For making metallic products through Additive Manufacturing (AM) processes, laser-based systems play very significant roles. Laser-based processes such as Selective Laser Melting (SLM) and Laser Engineered Net Shaping (LENS) are dominating processes...

  1. Enhancing phosphorus release from waste activated sludge containing ferric or aluminum phosphates by EDTA addition during anaerobic fermentation process.

    Science.gov (United States)

    Zou, Jinte; Zhang, Lili; Wang, Lin; Li, Yongmei

    2017-03-01

    The effect of ethylene diamine tetraacetic acid (EDTA) addition on phosphorus release from biosolids and phosphate precipitates during anaerobic fermentation was investigated. Meanwhile, the impact of EDTA addition on the anaerobic fermentation process was revealed. The results indicate that EDTA addition significantly enhanced the release of phosphorus from biosolids, ferric phosphate precipitate and aluminum phosphate precipitate during anaerobic fermentation, which is attributed to the complexation of metal ions and damage of cell membrane caused by EDTA. With the optimal EDTA addition of 19.5 mM (0.41 gEDTA/gSS), phosphorus release efficiency from biosolids was 82%, which was much higher than that (40%) without EDTA addition. Meanwhile, with 19.5 mM EDTA addition, almost all the phosphorus in ferric phosphate precipitate was released, while only 57% of phosphorus in aluminum phosphate precipitate was released. This indicates that phosphorus in ferric phosphate precipitate was much easier to be released than that in aluminum phosphate precipitate during anaerobic fermentation of sludge. In addition, proper EDTA addition facilitated the production of soluble total organic carbon and volatile fatty acids, as well as solid reduction during sludge fermentation, although methane production could be inhibited. Therefore, EDTA addition can be used as an alternative method for recovering phosphorus from waste activated sludge containing ferric or aluminum precipitates, as well as recovery of soluble carbon source. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. A safer, urea-based in situ hybridization method improves detection of gene expression in diverse animal species.

    Science.gov (United States)

    Sinigaglia, Chiara; Thiel, Daniel; Hejnol, Andreas; Houliston, Evelyn; Leclère, Lucas

    2018-02-01

    In situ hybridization is a widely employed technique allowing spatial visualization of gene expression in fixed specimens. It has greatly advanced our understanding of biological processes, including developmental regulation. In situ protocols are today routinely followed in numerous laboratories, and although details might change, they all include a hybridization step, where specific antisense RNA or DNA probes anneal to the target nucleic acid sequence. This step is generally carried out at high temperatures and in a denaturing solution, called hybridization buffer, commonly containing 50% (v/v) formamide - a hazardous chemical. When applied to the soft-bodied hydrozoan medusa Clytia hemisphaerica, we found that this traditional hybridization approach was not fully satisfactory, causing extensive deterioration of morphology and tissue texture which compromised our observation and interpretation of results. We thus tested alternative solutions for in situ detection of gene expression and, inspired by optimized protocols for Northern and Southern blot analysis, we substituted the 50% formamide with an equal volume of 8M urea solution in the hybridization buffer. Our new protocol not only yielded better morphologies and tissue consistency, but also notably improved the resolution of the signal, allowing more precise localization of gene expression and reducing aspecific staining associated with problematic areas. Given the improved results and reduced manipulation risks, we tested the urea protocol on other metazoans, two brachiopod species (Novocrania anomala and Terebratalia transversa) and the priapulid worm Priapulus caudatus, obtaining a similar reduction of aspecific probe binding. Overall, substitution of formamide by urea during in situ hybridization offers a safer alternative, potentially of widespread use in research, medical and teaching contexts. We encourage other workers to test this approach on their study organisms, and hope that they will also

  3. Safer food means food irradiation

    International Nuclear Information System (INIS)

    Steele, J.H.

    2000-01-01

    In this article the author presents the sanitary advantages that are brought by food irradiation. OMS experts state that this technique is safe and harmless for any average global dose between 10 KGy and 100 KGy. Whenever a seminar is held on the topic, it is always concluded that food irradiation should be promoted and favoured. In France food irradiation is authorized for some kinds of products and exceptionally above a 10 KGy dose. Historically food irradiation has been hampered in its development by its classification by American Authorities as food additives in 1958 (Delanay clause). The author draws a parallel between food irradiation and pasteurization or food deep-freezing in their beginnings. (A.C.)

  4. Statistical properties of a filtered Poisson process with additive random noise: distributions, correlations and moment estimation

    International Nuclear Information System (INIS)

    Theodorsen, A; Garcia, O E; Rypdal, M

    2017-01-01

    Filtered Poisson processes are often used as reference models for intermittent fluctuations in physical systems. Such a process is here extended by adding a noise term, either as a purely additive term to the process or as a dynamical term in a stochastic differential equation. The lowest order moments, probability density function, auto-correlation function and power spectral density are derived and used to identify and compare the effects of the two different noise terms. Monte-Carlo studies of synthetic time series are used to investigate the accuracy of model parameter estimation and to identify methods for distinguishing the noise types. It is shown that the probability density function and the three lowest order moments provide accurate estimations of the model parameters, but are unable to separate the noise types. The auto-correlation function and the power spectral density also provide methods for estimating the model parameters, as well as being capable of identifying the noise type. The number of times the signal crosses a prescribed threshold level in the positive direction also promises to be able to differentiate the noise type. (paper)

  5. Improved Morphology and Efficiency of n-i-p Planar Perovskite Solar Cells by Processing with Glycol Ether Additives

    KAUST Repository

    Ugur, Esma

    2017-07-31

    Planar perovskite solar cells can be prepared without high temperature processing steps typically associated with mesoporous device architectures; however, their efficiency has been lower and producing high quality perovskite films in planar devices has been challenging. Here, we report a modified two-step interdiffusion protocol suitable to prepare pin-hole free perovskite films with greatly improved morphology. This is achieved by simple addition of small amounts of glycol ethers to the preparation protocol. We unravel the impact the glycol ethers have on the perovskite film formation using in-situ UV-Vis absorbance and GIWAXS experiments. From these experiments we conclude: addition of glycol ethers changes the lead iodide to perovskite conversion dynamics and enhances the conversion efficiency, resulting in more compact polycrystalline films, and it creates micrometer-sized perovskite crystals vertically-aligned across the photoactive layer. Consequently, the average photovoltaic performance increases from 13.5% to 15.9% and reproduciability is enhanced, specifically when 2-methoxyethanol is used as additive.

  6. Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

    Science.gov (United States)

    Gesta, E.; Skovmand, O.; Espuche, E.; Fulchiron, R.

    2015-12-01

    The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives' ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration.

  7. Improved Morphology and Efficiency of n-i-p Planar Perovskite Solar Cells by Processing with Glycol Ether Additives

    KAUST Repository

    Ugur, Esma; Sheikh, Arif D.; Munir, Rahim; Khan, Jafar Iqbal; Barrit, Dounya; Amassian, Aram; Laquai, Fré dé ric

    2017-01-01

    Planar perovskite solar cells can be prepared without high temperature processing steps typically associated with mesoporous device architectures; however, their efficiency has been lower and producing high quality perovskite films in planar devices has been challenging. Here, we report a modified two-step interdiffusion protocol suitable to prepare pin-hole free perovskite films with greatly improved morphology. This is achieved by simple addition of small amounts of glycol ethers to the preparation protocol. We unravel the impact the glycol ethers have on the perovskite film formation using in-situ UV-Vis absorbance and GIWAXS experiments. From these experiments we conclude: addition of glycol ethers changes the lead iodide to perovskite conversion dynamics and enhances the conversion efficiency, resulting in more compact polycrystalline films, and it creates micrometer-sized perovskite crystals vertically-aligned across the photoactive layer. Consequently, the average photovoltaic performance increases from 13.5% to 15.9% and reproduciability is enhanced, specifically when 2-methoxyethanol is used as additive.

  8. Design and development of a layer-based additive manufacturing process for the realization of metal parts of designed mesostructure

    Science.gov (United States)

    Williams, Christopher Bryant

    Low-density cellular materials, metallic bodies with gaseous voids, are a unique class of materials that are characterized by their high strength, low mass, good energy absorption characteristics, and good thermal and acoustic insulation properties. In an effort to take advantage of this entire suite of positive mechanical traits, designers are tailoring the cellular mesostructure for multiple design objectives. Unfortunately, existing cellular material manufacturing technologies limit the design space as they are limited to certain part mesostructure, material type, and macrostructure. The opportunity that exists to improve the design of existing products, and the ability to reap the benefits of cellular materials in new applications is the driving force behind this research. As such, the primary research goal of this work is to design, embody, and analyze a manufacturing process that provides a designer the ability to specify the material type, material composition, void morphology, and mesostructure topology for any conceivable part geometry. The accomplishment of this goal is achieved in three phases of research: (1) Design---Following a systematic design process and a rigorous selection exercise, a layer-based additive manufacturing process is designed that is capable of meeting the unique requirements of fabricating cellular material geometry. Specifically, metal parts of designed mesostructure are fabricated via three-dimensional printing of metal oxide ceramic powder followed by post-processing in a reducing atmosphere. (2) Embodiment ---The primary research hypothesis is verified through the use of the designed manufacturing process chain to successfully realize metal parts of designed mesostructure. (3) Modeling & Evaluation ---The designed manufacturing process is modeled in this final research phase so as to increase understanding of experimental results and to establish a foundation for future analytical modeling research. In addition to an analysis of

  9. A randomised controlled trial using mobile advertising to promote safer sex and sun safety to young people.

    Science.gov (United States)

    Gold, J; Aitken, C K; Dixon, H G; Lim, M S C; Gouillou, M; Spelman, T; Wakefield, M; Hellard, M E

    2011-10-01

    Mobile phone text messages (SMS) are a promising method of health promotion, but a simple and low cost way to obtain phone numbers is required to reach a wide population. We conducted a randomised controlled trial with simultaneous brief interventions to (i) evaluate effectiveness of messages related to safer sex and sun safety and (ii) pilot the use of mobile advertising for health promotion. Mobile advertising subscribers aged 16-29 years residing in Victoria, Australia (n = 7606) were randomised to the 'sex' or 'sun' group and received eight messages during the 2008-2009 summer period. Changes in sex- and sun-related knowledge and behaviour were measured by questionnaires completed on mobile phones. At follow-up, the sex group had significantly higher sexual health knowledge and fewer sexual partners than the sun group. The sun group had no change in hat-wearing frequency compared with a significant decline in hat-wearing frequency in the sex group. This is the first study of mobile advertising for health promotion, which can successfully reach most young people. Challenges experienced with project implementation and evaluation should be considered as new technological approaches to health promotion continue to be expanded.

  10. Additive Manufacturing of IN100 Superalloy Through Scanning Laser Epitaxy for Turbine Engine Hot-Section Component Repair: Process Development, Modeling, Microstructural Characterization, and Process Control

    Science.gov (United States)

    Acharya, Ranadip; Das, Suman

    2015-09-01

    This article describes additive manufacturing (AM) of IN100, a high gamma-prime nickel-based superalloy, through scanning laser epitaxy (SLE), aimed at the creation of thick deposits onto like-chemistry substrates for enabling repair of turbine engine hot-section components. SLE is a metal powder bed-based laser AM technology developed for nickel-base superalloys with equiaxed, directionally solidified, and single-crystal microstructural morphologies. Here, we combine process modeling, statistical design-of-experiments (DoE), and microstructural characterization to demonstrate fully metallurgically bonded, crack-free and dense deposits exceeding 1000 μm of SLE-processed IN100 powder onto IN100 cast substrates produced in a single pass. A combined thermal-fluid flow-solidification model of the SLE process compliments DoE-based process development. A customized quantitative metallography technique analyzes digital cross-sectional micrographs and extracts various microstructural parameters, enabling process model validation and process parameter optimization. Microindentation measurements show an increase in the hardness by 10 pct in the deposit region compared to the cast substrate due to microstructural refinement. The results illustrate one of the very few successes reported for the crack-free deposition of IN100, a notoriously "non-weldable" hot-section alloy, thus establishing the potential of SLE as an AM method suitable for hot-section component repair and for future new-make components in high gamma-prime containing crack-prone nickel-based superalloys.

  11. CLOSURE REPORT FOR CORRECTIVE ACTION UNIT 115: AREA 25 TEST CELL A FACILITY, NEVADA TEST SITE, NEVADA

    International Nuclear Information System (INIS)

    2006-01-01

    This Closure Report (CR) describes the activities performed to close CAU 115, Area 25 Test Cell A Facility, as presented in the NDEP-approved SAFER Plan (NNSA/NSO, 2004). The SAFER Plan includes a summary of the site history, process knowledge, and closure standards. This CR provides a summary of the completed closure activities, documentation of waste disposal, and analytical and radiological data to confirm that the remediation goals were met and to document final site conditions. The approved closure alternative as presented in the SAFER Plan for CAU 115 (NNSA/NSO, 2004) was clean closure; however, closure in place was implemented under a Record of Technical Change (ROTC) to the SAFER Plan when radiological surveys indicated that the concrete reactor pad was radiologically activated and could not be decontaminated to meet free release levels. The ROTC is included as Appendix G of this report. The objectives of closure were to remove any trapped residual liquids and gases, dispose regulated and hazardous waste, decontaminate removable radiological contamination, demolish and dispose aboveground structures, remove the dewar as a best management practice (BMP), and characterize and restrict access to all remaining radiological contamination. Radiological contaminants of concern (COCs) included cobalt-60, cesium-137, strontium-90, uranium-234/235/236/238, and plutonium-239/240. Additional COCs included Resource Conservation and Recovery Act (RCRA) metals, polychlorinated biphenyls (PCBs), and asbestos

  12. Data on the surface morphology of additively manufactured Ti-6Al-4V implants during processing by plasma electrolytic oxidation

    NARCIS (Netherlands)

    van Hengel, I.A.J. (Ingmar A.J.); M. Riool (Martijn); L.E. Fratila-Apachitei (L.); J. Witte-Bouma (Janneke); E. Farrell (Eric); A.A. Zadpoor (Amir Abbas); S.A.J. Zaat (Sebastiaan); I. Apachitei (I.)

    2017-01-01

    textabstractAdditively manufactured Ti-6Al-4V implants were biofunctionalized using plasma electrolytic oxidation. At various time points during this process scanning electron microscopy imaging was performed to analyze the surface morphology (van Hengel et al., 2017) [1]. This data shows the

  13. Exploring the effects of ZVI addition on resource recovery in the anaerobic digestion process

    DEFF Research Database (Denmark)

    Puyol, D.; Flores-Alsina, Xavier; Segura, Y.

    2018-01-01

    not compensate the costs of ZVI purchase, and (b) ZVI dramatically decreases the P recovery potential in the digestate of the AD systems. This is the first study to experimentally and mathematically describe the effect of ZVI on biogas production/composition and on the fate of phosphorus compounds, and its......The influence of Zero Valent Iron (ZVI) addition on the potential resource recovery during the anaerobic digestion (AD) of domestic waste sludge is assessed. Potentially recoverable resources analyzed were nutrients such as struvite to recover P, and energy as biogas to recover C. Short term...... (biochemical methane potential tests, BMP) and long term (AD1, AD2) experiments are conducted using two types of set-up (batch, continuous). Process data (influent, effluent and biogas) is continuously collected and the dry digested sludge is analyzed by XPS. A mathematical model is developed based...

  14. Hierarchical random additive process and logarithmic scaling of generalized high order, two-point correlations in turbulent boundary layer flow

    Science.gov (United States)

    Yang, X. I. A.; Marusic, I.; Meneveau, C.

    2016-06-01

    Townsend [Townsend, The Structure of Turbulent Shear Flow (Cambridge University Press, Cambridge, UK, 1976)] hypothesized that the logarithmic region in high-Reynolds-number wall-bounded flows consists of space-filling, self-similar attached eddies. Invoking this hypothesis, we express streamwise velocity fluctuations in the inertial layer in high-Reynolds-number wall-bounded flows as a hierarchical random additive process (HRAP): uz+=∑i=1Nzai . Here u is the streamwise velocity fluctuation, + indicates normalization in wall units, z is the wall normal distance, and ai's are independently, identically distributed random additives, each of which is associated with an attached eddy in the wall-attached hierarchy. The number of random additives is Nz˜ln(δ /z ) where δ is the boundary layer thickness and ln is natural log. Due to its simplified structure, such a process leads to predictions of the scaling behaviors for various turbulence statistics in the logarithmic layer. Besides reproducing known logarithmic scaling of moments, structure functions, and correlation function [" close="]3/2 uz(x ) uz(x +r ) >, new logarithmic laws in two-point statistics such as uz4(x ) > 1 /2, 1/3, etc. can be derived using the HRAP formalism. Supporting empirical evidence for the logarithmic scaling in such statistics is found from the Melbourne High Reynolds Number Boundary Layer Wind Tunnel measurements. We also show that, at high Reynolds numbers, the above mentioned new logarithmic laws can be derived by assuming the arrival of an attached eddy at a generic point in the flow field to be a Poisson process [Woodcock and Marusic, Phys. Fluids 27, 015104 (2015), 10.1063/1.4905301]. Taken together, the results provide new evidence supporting the essential ingredients of the attached eddy hypothesis to describe streamwise velocity fluctuations of large, momentum transporting eddies in wall-bounded turbulence, while observed deviations suggest the need for further extensions of the

  15. EFFECT OF STARCH ADDITION ON THE PERFORMANCE AND SLUDGE CHARACTERIZATION OF UASB PROCESS TREATING METHANOLIC WASTEWATER

    Science.gov (United States)

    Yan, Feng; Kobayashi, Takuro; Takahashi, Shintaro; Li, Yu-You; Omura, Tatsuo

    A mesophilic(35℃) UASB reactor treating synthetic wastewater containing methanol with addition of starch was continuously operated for over 430 days by changing the organic loading rate from 2.5 to 120kg-COD/m3.d. The microbial community structure of the granules was analyzed with the molecular tools and its metabolic characteristics were evaluated using specific methanogenic activity tests. The process was successfully operated with over 98% soluble COD removal efficiency at VLR 30kg-COD/m3.d for approximately 300 days, and granulation satisfactory proceeded. The results of cloning and fluorescence in situ hybridization analysis suggest that groups related the genus Methanomethylovorans and the genus Methanosaeta were predominant in the reactor although only the genus Methanomethylovorans was predominant in the reactor treating methanolic wastewater in the previous study. Abundance of the granules over 0.5 mm in diameter in the reactor treating methanolic wastewater with addition of starch was 3 times larger than that in the reactor treating methanolic wastewater. Specific methanogenic activity tests in this study indicate that the methanol-methane pathway and the methanol-H2/CO2-methane pathway were predominant, and however, there was a certain level of activity for acetate-methane pathway unlike the reactor treating methanolic wastewater. These results suggest addition of starch might be responsible for diversifying the microbial community and encouraging the granulation.

  16. Sol-gel additive for systems with inorganic binders

    International Nuclear Information System (INIS)

    Akstinat, M.; Antenen, D.; Suter, W.

    1996-01-01

    A sol-gel additive for inorganic binder systems and sol-gel process for producing air-placed concrete and mortar by using such sol-gel additives are disclosed. Sol-gel additives for gel-derived inorganic binder systems (for example plaster, cement, lime, special slags, etc.) marked improve the consistency of such binder systems during processing or allow their consistency to be regulated. In addition, these sol-gel additives regulate setting times and substantially improve durability (chemical resistance, reduced permeability) and the mechanical properties of the set binder system. (author)

  17. Certification of Additive Manufacturing Processing Parameters through Physics-Based Predictive Simulation of Process-Defects-Microstructure

    Data.gov (United States)

    National Aeronautics and Space Administration — Additive manufacturing (AM), also known as 3D printing, is a next generation technology for cost-effective and accelerated way of manufacturing complex-shaped...

  18. Thermomechanical Processing of Structural Steels with Dilute Niobium Additions

    Science.gov (United States)

    Cui, Z.; Patel, J.; Palmiere, E. J.

    The recrystallisation behaviour of medium carbon steels with dilute Nb addition was investigated by means of plane strain compression tests and the observation of prior austenite microstructures during different deformation conditions. It was found that complete suppression of recrystallisation did not occur in the deformation temperature range investigated. At lower deformation temperatures, partial recrystallisation occurred in the higher Nb sample. This gives the potential to obtain a full suppression of recrystallisation at lower deformation temperatures.

  19. Data on the surface morphology of additively manufactured Ti-6Al-4V implants during processing by plasma electrolytic oxidation

    NARCIS (Netherlands)

    van Hengel, I.A.J.; Riool, Martijn; Fratila-Apachitei, E.L.; Witte-Bouma, Janneke; Farrell, Eric; Zadpoor, A.A.; Zaat, Sebastian A.J.; Apachitei, I.

    2017-01-01

    Additively manufactured Ti-6Al-4V implants were biofunctionalized using plasma electrolytic oxidation. At various time points during this process scanning electron microscopy imaging was performed to analyze the surface morphology (van Hengel et al., 2017) [1]. This data shows the changes in

  20. Practical use of ergonomics in industrial processes

    International Nuclear Information System (INIS)

    1976-01-01

    Six lectures deal with new developments in the application of ergonomic knowledge, in particular to nuclear technology. All contributions have in common the aspects of analysis and structure of man-machine-systems in which human operators have to process information and have to make decisions. Quoting a lot of examples from a variety of industrial sectors, the article discusses complexes of problems and ways of solving them concerning questions requiring the answer 'yes' or 'no', concerning the dialogue man-computer, the organization of central control mechanisms, the avoidance of human errors, influence of man on system safety, and the rational incorporation of ergonomics in system planning. This publication is meant to be a contribution to extend the knowledge on the organization of work from an ergonomic and engineer/psychological point of view. It is to show how the knowledge of the nature of man can be applied as a systems component in order to make industrial processes safer and more economical, and to entrust man with purposeful and satisfying tasks. (orig./LN) [de

  1. Processing of spent nickelcatalyst for fat recovery

    Directory of Open Access Journals (Sweden)

    NASIR Mohammad Ibraim

    2001-01-01

    Full Text Available Spent nickel catalyst (SNC has the potential of insulting the quality of the environment in a number of ways. Its disposal has a pollution effect. Optimum recovery of fat from SNC, could save the environment and reduce the oil loss. Hexane has been the solvent of choice for oil extraction. Alternative solvents considered to have been safer have been evaluated. Hexane, isopropanol, ethanol and heptane were examined using soxhlet extraction. While hexane is more efficient in oil recovery from SNC, isopropanol proved to be very good in clear separation of oil from waste material and also provides high solvent recovery compared to other solvents. Isopropanol extraction with chill separation of miscella into lower oil-rich phase, and an upper, solvent-rich recyclable phase save mush energy of vaporization for distilling. An aqueous extraction process with immiscible solvent assisted was tested. Solvent like hexane added to SNC, and water added later with continuous stirring. The mixture was stirred for about 30 minutes, prior to centrifugation. Aqueous process extracted less amount of oil compared to solvent extraction.

  2. A Soft Tooling process chain employing Additive Manufacturing for injection molding of a 3D component with micro pillars

    DEFF Research Database (Denmark)

    Zhang, Yang; Pedersen, David Bue; Segebrecht Gøtje, Asger

    2017-01-01

    The purpose of the research presented in this paper is to investigate the capability of a soft tooling process chain employing Additive Manufacturing (AM) for preproduction of an insert with micro features by injection molding. The Soft Tooling insert was manufactured in a high temperature...... photopolymer by Digital Light Processing (vat photopolymerization). The mold cavity was formed by two insert halves, by design; both inserts have four angled tines, with micro holes (Ø200 μm, 200 μm deep) on the surface. Injection molding with polyethylene was used with the soft tool inserts to manufacture...

  3. Design Process Control for Improved Surface Finish of Metal Additive Manufactured Parts of Complex Build Geometry

    Directory of Open Access Journals (Sweden)

    Mikdam Jamal

    2017-12-01

    Full Text Available Metal additive manufacturing (AM is increasingly used to create complex 3D components at near net shape. However, the surface finish (SF of the metal AM part is uneven, with surface roughness being variable over the facets of the design. Standard post-processing methods such as grinding and linishing often meet with major challenges in finishing parts of complex shape. This paper reports on research that demonstrated that mass finishing (MF processes are able to deliver high-quality surface finishes (Ra and Sa on AM-generated parts of a relatively complex geometry (both internal features and external facets under select conditions. Four processes were studied in this work: stream finishing, high-energy (HE centrifuge, drag finishing and disc finishing. Optimisation of the drag finishing process was then studied using a structured design of experiments (DOE. The effects of a range of finishing parameters were evaluated and optimal parameters and conditions were determined. The study established that the proposed method can be successfully applied in drag finishing to optimise the surface roughness in an industrial application and that it is an economical way of obtaining the maximum amount of information in a short period of time with a small number of tests. The study has also provided an important step in helping understand the requirements of MF to deliver AM-generated parts to a target quality finish and cycle time.

  4. Terminal addition in a cellular world.

    Science.gov (United States)

    Torday, J S; Miller, William B

    2018-07-01

    Recent advances in our understanding of evolutionary development permit a reframed appraisal of Terminal Addition as a continuous historical process of cellular-environmental complementarity. Within this frame of reference, evolutionary terminal additions can be identified as environmental induction of episodic adjustments to cell-cell signaling patterns that yield the cellular-molecular pathways that lead to differing developmental forms. Phenotypes derive, thereby, through cellular mutualistic/competitive niche constructions in reciprocating responsiveness to environmental stresses and epigenetic impacts. In such terms, Terminal Addition flows according to a logic of cellular needs confronting environmental challenges over space-time. A reconciliation of evolutionary development and Terminal Addition can be achieved through a combined focus on cell-cell signaling, molecular phylogenies and a broader understanding of epigenetic phenomena among eukaryotic organisms. When understood in this manner, Terminal Addition has an important role in evolutionary development, and chronic disease might be considered as a form of 'reverse evolution' of the self-same processes. Copyright © 2017. Published by Elsevier Ltd.

  5. Additive manufacturing in production: challenges and opportunities

    Science.gov (United States)

    Ahuja, Bhrigu; Karg, Michael; Schmidt, Michael

    2015-03-01

    Additive manufacturing, characterized by its inherent layer by layer fabrication methodology has been coined by many as the latest revolution in the manufacturing industry. Due to its diversification of Materials, processes, system technology and applications, Additive Manufacturing has been synonymized with terminology such as Rapid prototyping, 3D printing, free-form fabrication, Additive Layer Manufacturing, etc. A huge media and public interest in the technology has led to an innovative attempt of exploring the technology for applications beyond the scope of the traditional engineering industry. Nevertheless, it is believed that a critical factor for the long-term success of Additive Manufacturing would be its ability to fulfill the requirements defined by the traditional manufacturing industry. A parallel development in market trends and product requirements has also lead to a wider scope of opportunities for Additive Manufacturing. The presented paper discusses some of the key challenges which are critical to ensure that Additive Manufacturing is truly accepted as a mainstream production technology in the industry. These challenges would highlight on various aspects of production such as product requirements, process management, data management, intellectual property, work flow management, quality assurance, resource planning, etc. In Addition, changing market trends such as product life cycle, mass customization, sustainability, environmental impact and localized production will form the foundation for the follow up discussion on the current limitations and the corresponding research opportunities. A discussion on ongoing research to address these challenges would include topics like process monitoring, design complexity, process standardization, multi-material and hybrid fabrication, new material development, etc.

  6. Written production of learners of Portuguese as an additional foreign language: referentiation as a sociocognitive processing resource

    Directory of Open Access Journals (Sweden)

    Lucia Rottava

    2011-12-01

    Full Text Available This article discusses referentiation in texts written by learners of Portuguese as an additional foreign language. Referentiation consists of construction and reconstruction of discourse objects, a product that results from cognitive and interactive activity. Among forms of interaction, written production is an interactive process as meanings derive from the interaction between writer/reader and text in complex and multifaceted experiences that involve prior experiences and/or knowledge, besides the interlocutor’s discursive purpose. Therefore, the text is the result of an action ‘under construction’ made possible through the use of language. Data for this article come from written production developed in classes of Portuguese as a foreign language. The findings reveal learners’ textual processing and its peculiarities resulting from the learners’ proficiency levels and the requirements of the type and theme of the specified task.

  7. Advancing alternatives analysis: The role of predictive toxicology in selecting safer chemical products and processes.

    Science.gov (United States)

    Malloy, Timothy; Zaunbrecher, Virginia; Beryt, Elizabeth; Judson, Richard; Tice, Raymond; Allard, Patrick; Blake, Ann; Cote, Ila; Godwin, Hilary; Heine, Lauren; Kerzic, Patrick; Kostal, Jakub; Marchant, Gary; McPartland, Jennifer; Moran, Kelly; Nel, Andre; Ogunseitan, Oladele; Rossi, Mark; Thayer, Kristina; Tickner, Joel; Whittaker, Margaret; Zarker, Ken

    2017-09-01

    Alternatives analysis (AA) is a method used in regulation and product design to identify, assess, and evaluate the safety and viability of potential substitutes for hazardous chemicals. It requires toxicological data for the existing chemical and potential alternatives. Predictive toxicology uses in silico and in vitro approaches, computational models, and other tools to expedite toxicological data generation in a more cost-effective manner than traditional approaches. The present article briefly reviews the challenges associated with using predictive toxicology in regulatory AA, then presents 4 recommendations for its advancement. It recommends using case studies to advance the integration of predictive toxicology into AA, adopting a stepwise process to employing predictive toxicology in AA beginning with prioritization of chemicals of concern, leveraging existing resources to advance the integration of predictive toxicology into the practice of AA, and supporting transdisciplinary efforts. The further incorporation of predictive toxicology into AA would advance the ability of companies and regulators to select alternatives to harmful ingredients, and potentially increase the use of predictive toxicology in regulation more broadly. Integr Environ Assess Manag 2017;13:915-925. © 2017 SETAC. © 2017 SETAC.

  8. Use of soft hydrothermal processing to improve and recycle bedding for laboratory animals.

    Science.gov (United States)

    Miyamoto, T; Li, Z; Kibushi, T; Yamasaki, N; Kasai, N

    2008-10-01

    Cage bedding for laboratory rodents can influence animal wellbeing and thus the experimental data. In addition, a large amount of used bedding containing excrement is discharged as medical waste from life science institutes and breeding companies. We developed a ground-breaking system to improve fresh bedding and recycle used bedding by applying a soft hydrothermal process with high-temperature and high-pressure dry steam. The system removes both harmful organic components and aromatic hydrocarbons that can affect animals' metabolism. The purpose of the present study was to evaluate the chemical and physical properties of the improved fresh bedding and the recycled used bedding treated by the system. The results showed that 68-99% of the predominant aromatic hydrocarbons were removed from fresh bedding treated at 0.35 MPa and 140 degrees C for 120 min ('improved bedding'). In addition, 59.4-99.0% of predominant harmful organic compounds derived from excrement were removed from used bedding treated at 0.45 MPa and 150 degrees C for 60 min ('recycled bedding'). The soft hydrothermal treatment increased the number of acidic functional groups on the bedding surface and gave it the high adsorptive efficiency of ammonia gas. Harmful substances such as microorganisms, heavy metals and pesticides decreased below the detection limit. The results clearly showed that the improved and recycled bedding is safer for laboratory rodents and has the potential to ameliorate conditions in primary and secondary enclosures (e.g. cages and animal rooms) used for maintaining laboratory animals. This process may be one of the most advanced techniques in providing an alternative to softwood and other bedding, economizing through the recycling of used bedding and reducing bedding waste from animal facilities.

  9. Additive effects in radiation grafting and curing

    International Nuclear Information System (INIS)

    Viengkhou, V.; Ng, L.

    1996-01-01

    Full text: Detailed studies on the accelerative effect of novel additives in radiation grafting and curing using acrylated monomer/oligomer systems have been performed in the presence of ionising radiation and UV as sources. Methyl methacrylate (MMA) is used as typical monomer for these grafting studies in the presence of the additives with model backbone polymers, cellulose and propropylene. Additives which have been found to accelerate these grafting processes are: mineral acid, occlusion compounds like urea, thermal initiators and photoinitiators as well as multifunctional monomers such as multifunctional acrylates. The results from irradiation with gamma rays have also been compared with irradiation from a 90W UV lamp. The role of the above additives in accelerating the analogous process of radiation curing has been investigated. Acrylated urethanes, epoxies and polyesters are used as oligomers together with acrylated monomers in this work with uv lamps of 300 watts/inch as radiation source. In the UV curing process bonding between film and substrate is usually due to physical forces. In the present work the presence of additives are shown to influence the occurrence of concurrent grafting during cure thus affecting the nature of the bonding of the cured film. The conditions under which concurrent grafting with UV can occur will be examined. A mechanism for accelerative effect of these additives in both grafting and curing processes has been proposed involving radiation effects and partitioning phenomena

  10. Sensing and controlling resin-layer thickness in additive manufacturing processes

    NARCIS (Netherlands)

    Kozhevnikov, A.

    2017-01-01

    This AM-TKI project in collaboration with TNO focusses on the sensing and control of resin-layer thickness in AM applications. Industrial Additive Manufacturing is considered to be a potential breakthrough production technology for many applications. A specific AM implementation is VAT photo

  11. Polylactides in additive biomanufacturing.

    Science.gov (United States)

    Poh, Patrina S P; Chhaya, Mohit P; Wunner, Felix M; De-Juan-Pardo, Elena M; Schilling, Arndt F; Schantz, Jan-Thorsten; van Griensven, Martijn; Hutmacher, Dietmar W

    2016-12-15

    New advanced manufacturing technologies under the alias of additive biomanufacturing allow the design and fabrication of a range of products from pre-operative models, cutting guides and medical devices to scaffolds. The process of printing in 3 dimensions of cells, extracellular matrix (ECM) and biomaterials (bioinks, powders, etc.) to generate in vitro and/or in vivo tissue analogue structures has been termed bioprinting. To further advance in additive biomanufacturing, there are many aspects that we can learn from the wider additive manufacturing (AM) industry, which have progressed tremendously since its introduction into the manufacturing sector. First, this review gives an overview of additive manufacturing and both industry and academia efforts in addressing specific challenges in the AM technologies to drive toward AM-enabled industrial revolution. After which, considerations of poly(lactides) as a biomaterial in additive biomanufacturing are discussed. Challenges in wider additive biomanufacturing field are discussed in terms of (a) biomaterials; (b) computer-aided design, engineering and manufacturing; (c) AM and additive biomanufacturing printers hardware; and (d) system integration. Finally, the outlook for additive biomanufacturing was discussed. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. SAFER - Company Snapshot - SAFER - Company Snapshot

    Data.gov (United States)

    Department of Transportation — The Company Snapshot is a concise electronic record of company identification, size, commodity information, and safety record, including the safety rating (if any),...

  13. Laser and electron-beam powder-bed additive manufacturing of metallic implants: A review on processes, materials and designs.

    Science.gov (United States)

    Sing, Swee Leong; An, Jia; Yeong, Wai Yee; Wiria, Florencia Edith

    2016-03-01

    Additive manufacturing (AM), also commonly known as 3D printing, allows the direct fabrication of functional parts with complex shapes from digital models. In this review, the current progress of two AM processes suitable for metallic orthopaedic implant applications, namely selective laser melting (SLM) and electron beam melting (EBM) are presented. Several critical design factors such as the need for data acquisition for patient-specific design, design dependent porosity for osteo-inductive implants, surface topology of the implants and design for reduction of stress-shielding in implants are discussed. Additive manufactured biomaterials such as 316L stainless steel, titanium-6aluminium-4vanadium (Ti6Al4V) and cobalt-chromium (CoCr) are highlighted. Limitations and future potential of such technologies are also explored. © 2015 Orthopaedic Research Society. Published by Wiley Periodicals, Inc.

  14. Shades of Emotion: What the Addition of Sunglasses or Masks to Faces Reveals about the Development of Facial Expression Processing

    Science.gov (United States)

    Roberson, Debi; Kikutani, Mariko; Doge, Paula; Whitaker, Lydia; Majid, Asifa

    2012-01-01

    Three studies investigated developmental changes in facial expression processing, between 3 years-of-age and adulthood. For adults and older children, the addition of sunglasses to upright faces caused an equivalent decrement in performance to face inversion. However, younger children showed "better" classification of expressions of faces wearing…

  15. Advanced Process Chains for Prototyping and Pilot Production based on Additive Manufacturing

    DEFF Research Database (Denmark)

    Mischkot, Michael

    2015-01-01

    For many years, Additive Manufacturing (AM) has been a well-established production technology used mainly for rapid prototyping. But the need for increased flexibility and economic low volume production led to the discovery of Additive Manufacturing as a suitable fabrication technique (Mellor 2013...

  16. Community Vision and Interagency Alignment: A Community Planning Process to Promote Active Transportation.

    Science.gov (United States)

    DeGregory, Sarah Timmins; Chaudhury, Nupur; Kennedy, Patrick; Noyes, Philip; Maybank, Aletha

    2016-04-01

    In 2010, the Brooklyn Active Transportation Community Planning Initiative launched in 2 New York City neighborhoods. Over a 2-year planning period, residents participated in surveys, school and community forums, neighborhood street assessments, and activation events-activities that highlighted the need for safer streets locally. Consensus among residents and key multisectoral stakeholders, including city agencies and community-based organizations, was garnered in support of a planned expansion of bicycling infrastructure. The process of building on community assets and applying a collective impact approach yielded changes in the built environment, attracted new partners and resources, and helped to restore a sense of power among residents.

  17. Safety in numbers in Australia: more walkers and bicyclists, safer walking and bicycling.

    Science.gov (United States)

    Robinson, Dorothy L

    2005-04-01

    Overseas research shows that fatality and injury risks per cyclist and pedestrian are lower when there are more cyclists and pedestrians. Do Australian data follow the same exponential 'growth rule' where (Injuries)/(Amount of cycling) is proportional to ((Amount of cycling)-0.6)? Fatality and injury risks were compared using three datasets: 1) fatalities and amounts of cycling in Australian States in the 1980s; 2) fatality and injury rates over time in Western Australia as cycling levels increased; and 3) deaths, serious head injuries and other serious injuries to cyclists and pedestrians in Victoria, before and after the fall in cycling with the helmet law. In Australia, the risks of fatality and injury per cyclist are lower when cycling is more prevalent. Cycling was safest and most popular in the Australian Capital Territory (ACT), Queensland and Western Australia (WA). New South Wales residents cycled only 47% as much as residents of Queensland and WA, but had 53% more fatalities per kilometre, consistent with the growth rule prediction of 52% more for half as much cycling. Cycling also became safer in WA as more people cycled. Hospitalisation rates per 10,000 regular cyclists fell from 29 to 15, and reported deaths and serious injuries from 5.6 to 3.8 as numbers of regular cyclists increased. In Victoria, after the introduction of compulsory helmets, there was a 30% reduction in cycling and it was associated with a higher risk of death or serious injury per cyclist, outweighing any benefits of increased helmet wearing. As with overseas data, the exponential growth rule fits Australian data well. If cycling doubles, the risk per kilometre falls by about 34%; conversely, if cycling halves, the risk per kilometre will be about 52% higher. Policies that adversely influence the amount of cycling (for example, compulsory helmet legislation) should be reviewed.

  18. Additive manufacturing: state-of-the-art and application framework

    DEFF Research Database (Denmark)

    Rodrigues, Vinicius Picanco; de Senzi Zancul, Eduardo; Gonçalves Mançanares, Cauê

    2017-01-01

    Additive manufacturing encompasses a class of production processes with increasing applications indifferent areas and supply chains. Due to its flexibility for production in small batches and the versatilityof materials and geometries, this technology is recognized as being capable...... of revolutionizing theproduction processes as well as changing production strategies that are currently employed. However,there are different technologies under the generic label of additive manufacturing, materials and applicationareas with different requirements. Given the growing importance of additive...... manufacturingas a production process, and also considering the need to have a better insight into the potential applicationsfor driving research and development efforts, this article presents a proposal of organizationfor additive manufacturing applications in seven areas. Additionally, the article provides...

  19. Continued evaluation of pothole patching equipment, materials, and processes.

    Science.gov (United States)

    2014-06-14

    After the deaths of two Caltrans workers who were patching potholes in 2006-2007, Caltrans tasked the Advanced Highway Maintenance and Construction Technology (AHMCT) Research Center with developing a safer and more efficient means of patching pothol...

  20. Additive Manufacturing of Metastable Beta Titanium Alloys

    Science.gov (United States)

    Yannetta, Christopher J.

    Additive manufacturing processes of many alloys are known to develop texture during the deposition process due to the rapid reheating and the directionality of the dissipation of heat. Titanium alloys and with respect to this study beta titanium alloys are especially susceptible to these effects. This work examines Ti-20wt%V and Ti-12wt%Mo deposited under normal additive manufacturing process parameters to examine the texture of these beta-stabilized alloys. Both microstructures contained columnar prior beta grains 1-2 mm in length beginning at the substrate with no visible equiaxed grains. This microstructure remained constant in the vanadium system throughout the build. The microstructure of the alloy containing molybdenum changed from a columnar to an equiaxed structure as the build height increased. Eighteen additional samples of the Ti-Mo system were created under different processing parameters to identify what role laser power and travel speed have on the microstructure. There appears to be a correlation in alpha lath size and power density. The two binary alloys were again deposited under the same conditions with the addition of 0.5wt% boron to investigate the effects an insoluble interstitial alloying element would have on the microstructure. The size of the prior beta grains in these two alloys were reduced with the addition of boron by approximately 50 (V) and 100 (Mo) times.

  1. Why do drivers become safer over the first three months of driving? A longitudinal qualitative study.

    Science.gov (United States)

    Day, Marianne R; Thompson, Andrew R; Poulter, Damian R; Stride, Christopher B; Rowe, Richard

    2018-08-01

    Drivers are at high crash risk when they begin independent driving, with liability decreasing steeply over the first three months. Their behavioural development, and other changes underlying improved safety are not well understood. We adopted an innovative longitudinal qualitative design, with thirteen newly qualified drivers completing a total of 36 semi-structured interviews, one, two and three months after acquiring a full UK driving license. The interviews probed high-risk factors for new drivers, as well as allowing space for generating novel road safety issues. Analysis adopted a dual deductive and inductive interpretative thematic approach, identifying three super-ordinate themes: (1) Improvements in car control skills and situation awareness; (2) A reduction in the thrill of taking risks when driving against a background of generally increasing driving speed; (3) Early concerns about their social status in the eyes of other road users during the early stages of driving, which may put pressure on them to drive faster than they felt comfortable with. The study provides important new leads towards understanding how novice driving becomes safer over the first few months of driving, including how well-studied concepts of driving skill and style may change during development of independent driving, and bringing the less rigorously studied concept of social status into focus. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

  2. Successful long-term maintenance following Nutrition Care Process Terminology implementation across a state-wide health-care system.

    Science.gov (United States)

    Vivanti, Angela; O'Sullivan, Therese A; Porter, Jane; Hogg, Marion

    2017-09-01

    Three years following a state-wide Nutrition Care Process Terminology (NCPT) implementation project, the present study aimed to (i) assess changes in NCPT knowledge and attitudes, (ii) identify implementation barriers and enablers and (iii) seek managers' opinions post-implementation. Pre-implementation and three years post-implementation, all Queensland Government hospitals state-wide were invited to repeat a validated NCPT survey. Additionally, a separate survey sought dietetic managers' opinions regarding NCPT's use and acceptance, usefulness for patient care, role in service planning and continued use. A total of 238 dietitians completed the survey in 2011 and 82 dietitians in 2014. Use of diagnostic statement in the previous six months improved (P  0.05). Key elements in sustaining NCPT implementation over three years included ongoing management support, workshops/tutorials, discussion and mentor and peer support. The most valued resources were pocket guides, ongoing workshops/tutorials and mentor support. Dietetic managers held many positive NCPT views, however, opinions differed around the usefulness of service planning, safer practice, improving patient care and facilitating communication. Some managers would not support NCPT unless it was recommended for practice. Immediate improvements following the NCPT implementation project were sustained over three years. Moving forward, a professional focus on continuing to incorporate NCPT into standard practice will provide structure for process and outcomes assessment. © 2017 State of Queensland. Nutrition and Dietetics © 2017 Dietitians Association of Australia.

  3. Additive Manufacturing Design Considerations for Liquid Engine Components

    Science.gov (United States)

    Whitten, Dave; Hissam, Andy; Baker, Kevin; Rice, Darron

    2014-01-01

    The Marshall Space Flight Center's Propulsion Systems Department has gained significant experience in the last year designing, building, and testing liquid engine components using additive manufacturing. The department has developed valve, duct, turbo-machinery, and combustion device components using this technology. Many valuable lessons were learned during this process. These lessons will be the focus of this presentation. We will present criteria for selecting part candidates for additive manufacturing. Some part characteristics are 'tailor made' for this process. Selecting the right parts for the process is the first step to maximizing productivity gains. We will also present specific lessons we learned about feature geometry that can and cannot be produced using additive manufacturing machines. Most liquid engine components were made using a two-step process. The base part was made using additive manufacturing and then traditional machining processes were used to produce the final part. The presentation will describe design accommodations needed to make the base part and lessons we learned about which features could be built directly and which require the final machine process. Tolerance capabilities, surface finish, and material thickness allowances will also be covered. Additive Manufacturing can produce internal passages that cannot be made using traditional approaches. It can also eliminate a significant amount of manpower by reducing part count and leveraging model-based design and analysis techniques. Information will be shared about performance enhancements and design efficiencies we experienced for certain categories of engine parts.

  4. Laser polishing of additive manufactured Ti alloys

    Science.gov (United States)

    Ma, C. P.; Guan, Y. C.; Zhou, W.

    2017-06-01

    Laser-based additive manufacturing has attracted much attention as a promising 3D printing method for metallic components in recent years. However, surface roughness of additive manufactured components has been considered as a challenge to achieve high performance. In this work, we demonstrate the capability of fiber laser in polishing rough surface of additive manufactured Ti-based alloys as Ti-6Al-4V and TC11. Both as-received surface and laser-polished surfaces as well as cross-section subsurfaces were analyzed carefully by White-Light Interference, Confocal Microscope, Focus Ion Beam, Scanning Electron Microscopy, Energy Dispersive Spectrometer, and X-ray Diffraction. Results revealed that as-received Ti-based alloys with surface roughness more than 5 μm could be reduce to less than 1 μm through laser polishing process. Moreover, microstructure, microhardness and wear resistance of laser-polished zone was investigated in order to examine the thermal effect of laser polishing processing on the substrate of additive manufactured Ti alloys. This proof-of-concept process has the potential to effectively improve the surface roughness of additive manufactured metallic alloy by local polishing method without damage to the substrate.

  5. Processing and characterization of glass reinforced biogenic hydroxyapatite composites with ferromagnetic additives

    Directory of Open Access Journals (Sweden)

    Nataliya Pinchuk

    2008-06-01

    Full Text Available Biogenic hydroxyapatite-glass composites, with addition of up to 2 wt.% of Fe or Fe3O4, were fabricated from biogenic hydroxyapatite powder and four types of reinforcing glasses by sintering under different conditions. It has been established that the relative density, mechanical and magnetic properties of the prepared composites depend on the composition and sintering conditions. The composites with 1 wt.% Fe or Fe3O4 sintered at 500°С in vacuum have a magnetic susceptibility of 2–3·10-3 cm3/g. This parameter decreases to 0.858·10-3 cm3/g for the specimens with 1 wt.% additives sintered at 800°С in vacuum and to 0.27–1.3·10-3cm3/g for the specimens with 2 wt.% additives sintered at 500°С under the usual atmospheric conditions. The magnetic susceptibility for the specimens with 2 wt.% additives sintered at 780°С under the same atmospheric conditions decreases to 0.24–1.25·10-6 cm3/g. These ferromagnetic additives influence the degradation rate in vitro within the first 40 min of the composite soaking. Short-term treatment of specimens by the magnetic field leads to an increase in the initial degradation rate, but insignificantly influences it within more prolonged soaking.

  6. Inherent health and environmental risk assessment of nanostructured metal oxide production processes.

    Science.gov (United States)

    Torabifard, Mina; Arjmandi, Reza; Rashidi, Alimorad; Nouri, Jafar; Mohammadfam, Iraj

    2018-01-10

    The health and environmental effects of chemical processes can be assessed during the initial stage of their production. In this paper, the Chemical Screening Tool for Exposure and Environmental Release (ChemSTEER) software was used to compare the health and environmental risks of spray pyrolysis and wet chemical techniques for the fabrication of nanostructured metal oxide on a semi-industrial scale with a capacity of 300 kg/day in Iran. The pollution sources identified in each production process were pairwise compared in Expert Choice software using indicators including respiratory damage, skin damage, and environmental damages including air, water, and soil pollution. The synthesis of nanostructured zinc oxide using the wet chemical technique (with 0.523 wt%) leads to lower health and environmental risks compared to when spray pyrolysis is used (with 0.477 wt%). The health and environmental risk assessment of nanomaterial production processes can help select safer processes, modify the operation conditions, and select or modify raw materials that can help eliminate the risks.

  7. Reducing widespread pipe sharing and risky sex among crystal methamphetamine smokers in Toronto: do safer smoking kits have a potential role to play?

    Directory of Open Access Journals (Sweden)

    Hunter Charlotte

    2012-02-01

    Full Text Available Abstract Background Crystal methamphetamine smoking is associated with many negative health consequences, including the potential for transmission of hepatitis. We examined whether or not a kit for crystal methamphetamine smoking might have some potential to reduce the negative health effects of crystal methamphetamine smoking. Methods Five focus groups were conducted with crystal methamphetamine smokers recruited by community health agencies and youth shelters in Toronto, Canada. Target groups included homeless/street-involved youth, sex workers, men who have sex with men, and youth in the party scene. Participants (n = 32 were asked questions about motivations for crystal methamphetamine use, the process of smoking, health problems experienced, sharing behaviour, risky sexual practices, and the ideal contents of a harm reduction kit. Results Pipe sharing was widespread among participants and was deemed integral to the social experience of smoking crystal methamphetamine. Heated pipes were unlikely to cause direct injuries, but participants mentioned having dry, cracked lips, which may be a vector for disease transmission. Many reported having sex with multiple partners and being less likely to use condoms while on the drug. Demand for harm reduction kits was mixed. Conclusions Changing pipe sharing behaviours may be difficult because many participants considered sharing to be integral to the social experience of smoking crystal methamphetamine. Within the context of a broader health promotion and prevention program, pilot testing of safer smoking kits to initiate discussion and education on the risks associated with sharing pipes and unprotected sex for some communities (e.g., homeless/street-involved youth is worth pursuing.

  8. Merits and Demerits of Food Additives

    Institute of Scientific and Technical Information of China (English)

    Xuening; YANG; Yong; ZHAN

    2014-01-01

    Food additive is a double-edged sword. It has merits and demerits. Food additives have such merits as improving sensory properties of foods,preventing deterioration and extending the shelf life,increasing varieties of foods,enhancing convenience of foods,facilitating food processing,and satisfying other demands. However,excessive and illegal use of food additives will exert adverse influence on food security.Therefore,it is required to take proper measures to bring merits of food additives into full play,and get rid of their demerits.

  9. Laser additive manufacturing of high-performance materials

    CERN Document Server

    Gu, Dongdong

    2015-01-01

    This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization, and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering, and mechanical engineering. This is a book for researchers, students, practicing engineers, and manufacturing industry professionals interested i...

  10. Numerical modeling of heat-transfer and the influence of process parameters on tailoring the grain morphology of IN718 in electron beam additive manufacturing

    International Nuclear Information System (INIS)

    Raghavan, Narendran; Dehoff, Ryan; Pannala, Sreekanth; Simunovic, Srdjan; Kirka, Michael; Turner, John; Carlson, Neil; Babu, Sudarsanam S.

    2016-01-01

    The fabrication of 3-D parts from CAD models by additive manufacturing (AM) is a disruptive technology that is transforming the metal manufacturing industry. The correlation between solidification microstructure and mechanical properties has been well understood in the casting and welding processes over the years. This paper focuses on extending these principles to additive manufacturing to understand the transient phenomena of repeated melting and solidification during electron beam powder melting process to achieve site-specific microstructure control within a fabricated component. In this paper, we have developed a novel melt scan strategy for electron beam melting of nickel-base superalloy (Inconel 718) and also analyzed 3-D heat transfer conditions using a parallel numerical solidification code (Truchas) developed at Los Alamos National Laboratory. The spatial and temporal variations of temperature gradient (G) and growth velocity (R) at the liquid-solid interface of the melt pool were calculated as a function of electron beam parameters. By manipulating the relative number of voxels that lie in the columnar or equiaxed region, the crystallographic texture of the components can be controlled to an extent. The analysis of the parameters provided optimum processing conditions that will result in columnar to equiaxed transition (CET) during the solidification. The results from the numerical simulations were validated by experimental processing and characterization thereby proving the potential of additive manufacturing process to achieve site-specific crystallographic texture control within a fabricated component.

  11. Safer Soldering Guidelines and Instructional Resources

    Science.gov (United States)

    Love, Tyler S.; Tomlinson, Joel

    2018-01-01

    Soldering is a useful and necessary process for many classroom, makerspace, Fab Lab, technology and engineering lab, and science lab activities. As described in this article, soldering can pose many safety risks without proper engineering controls, standard operating procedures, and direct instructor supervision. There are many safety hazards…

  12. Footprints of a trypanosomatid RNA world: pre-small subunit rRNA processing by spliced leader addition trans-splicing

    Directory of Open Access Journals (Sweden)

    Mario Gustavo Mayer

    2012-06-01

    Full Text Available The addition of a capped mini-exon [spliced leader (SL] through trans-splicing is essential for the maturation of RNA polymerase (pol II-transcribed polycistronic pre-mRNAs in all members of the Trypanosomatidae family. This process is an inter-molecular splicing reaction that follows the same basic rules of cis-splicing reactions. In this study, we demonstrated that mini-exons were added to precursor ribosomal RNA (pre-rRNA are transcribed by RNA pol I, including the 5' external transcribed spacer (ETS region. Additionally, we detected the SL-5'ETS molecule using three distinct methods and located the acceptor site between two known 5'ETS rRNA processing sites (A' and A1 in four different trypanosomatids. Moreover, we detected a polyadenylated 5'ETS upstream of the trans-splicing acceptor site, which also occurs in pre-mRNA trans-splicing. After treatment with an indirect trans-splicing inhibitor (sinefungin, we observed SL-5'ETS decay. However, treatment with 5-fluorouracil (a precursor of RNA synthesis that inhibits the degradation of pre-rRNA led to the accumulation of SL-5'ETS, suggesting that the molecule may play a role in rRNA degradation. The detection of trans-splicing in these molecules may indicate broad RNA-joining properties, regardless of the polymerase used for transcription.

  13. Closure Report for Corrective Action Unit 118: Area 27 Super Kukla Facility, Nevada Test Site, Nevada, Revision 0

    International Nuclear Information System (INIS)

    Mark Burmeister

    2007-01-01

    This CR provides documentation and justification for the closure of CAU 118 without further corrective action. This justification is based on process knowledge and the results of the investigative and closure activities conducted in accordance with the CAU 118 SAFER Plan: Streamlined Approach for Environmental Restoration (SAFER) Plan for CAU 118: Area 27 Super Kukla Facility, Nevada Test Site, Nevada (NNSA/NSO, 2006). The SAFER Plan provides information relating to site history as well as the scope and planning of the investigation. This CR also provides the analytical and radiological survey data to confirm that the remediation goals were met as specified in the CAU 118 SAFER Plan (NNSA/NSO, 2006). The Nevada Division of Environmental Protection (NDEP) approved the CAU 118 SAFER Plan (Murphy, 2006), which recommends closure in place with use restrictions (URs)

  14. Subgaleo-peritoneal shunt: An effective and safer alternative to lumboperitoneal shunt in the management of persistent or recurrent iatrogenic cranial pseudomeningoceles.

    Science.gov (United States)

    Kiran, Narayanam Anantha Sai; Thakar, Sumit; Mohan, Dilip; Aryan, Saritha; Rao, Arun Sadashiva; Hegde, Alangar S

    2013-01-01

    Subgaleo-peritoneal (SP) shunting for pseudomeningoceles (PMCs) is an effective and safer alternative as compared to the lumboperitoneal (LP) shunt. SP shunting was done in six patients (14-60 years) with persistent or recurrent PMCs using the cranial (ventricular part) and the distal parts of a Chhabra shunt connected by a rigid connector without any intervening chamber or valve. Two patients had undergone a prior LP shunt that had failed. One patient was unsuitable for a LP shunt placement. The PMC subsided completely in all the patients following the SP shunt. In one patient, the shunt got displaced and required repositioning. None of the patients developed symptoms of over-drainage or any other complication. All patients were asymptomatic at a mean follow-up of 15 months. These results suggest that SP shunting is a safe, simple, and effective alternative to the traditional LP shunt in the management of persistent or recurrent cranial PMCs.

  15. The Critical Choice of PEDOT: PSS Additives for Long Term Stability of Roll‐to‐Roll Processed OPVs

    DEFF Research Database (Denmark)

    Roth, Bérenger; Benatto, Gisele Alves dos Reis; Corazza, Michael

    2015-01-01

    The impact of additives mixed with poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) on the stability of organic photovoltaic modules is investigated for fully ambient roll-to-roll (R2R) processed indium tin oxide free modules. Four different PEDOT:PSS inks from two different...... on organic photovoltaic stability (ISOS). For the harsh indoor test (ISOS-L-3) only a slight difference in stability is observed between the different modules. During both ISOS-L-3 and ISOS-D-3 one new failure mode is observed as a result of tiny air inclusions in the barrier foil and a R2R method...

  16. Synthesis and characterization of Ti-27.5Nb alloy made by CLAD® additive manufacturing process for biomedical applications.

    Science.gov (United States)

    Fischer, M; Laheurte, P; Acquier, P; Joguet, D; Peltier, L; Petithory, T; Anselme, K; Mille, P

    2017-06-01

    Biocompatible beta-titanium alloys such as Ti-27.5(at.%)Nb are good candidates for implantology and arthroplasty applications as their particular mechanical properties, including low Young's modulus, could significantly reduce the stress-shielding phenomenon usually occurring after surgery. The CLAD® process is a powder blown additive manufacturing process that allows the manufacture of patient specific (i.e. custom) implants. Thus, the use of Ti-27.5(at.%)Nb alloy formed by CLAD® process for biomedical applications as a mean to increase cytocompatibility and mechanical biocompatibility was investigated in this study. The microstructural properties of the CLAD-deposited alloy were studied with optical microscopy and electron back-scattered diffraction (EBSD) analysis. The conservation of the mechanical properties of the Ti-27.5Nb material after the transformation steps (ingot-powder atomisation-CLAD) were verified with tensile tests and appear to remain close to those of reference material. Cytocompatibility of the material and subsequent cell viability tests showed that no cytotoxic elements are released in the medium and that viable cells proliferated well. Copyright © 2017 Elsevier B.V. All rights reserved.

  17. The effect of activated carbon addition on membrane bioreactor processes for wastewater treatment and reclamation - A critical review.

    Science.gov (United States)

    Skouteris, George; Saroj, Devendra; Melidis, Paraschos; Hai, Faisal I; Ouki, Sabèha

    2015-06-01

    This review concentrates on the effect of activated carbon (AC) addition to membrane bioreactors (MBRs) treating wastewaters. Use of AC-assisted MBRs combines adsorption, biodegradation and membrane filtration. This can lead to advanced removal of recalcitrant pollutants and mitigation of membrane fouling. The relative contribution of adsorption and biodegradation to overall removal achieved by an AC-assisted MBR process can vary, and "biological AC" may not fully develop due to competition of target pollutants with bulk organics in wastewater. Thus periodic replenishment of spent AC is necessary. Sludge retention time (SRT) governs the frequency of spent AC withdrawal and addition of fresh AC, and is an important parameter that significantly influences the performance of AC-assisted MBRs. Of utmost importance is AC dosage because AC overdose may aggravate membrane fouling, increase sludge viscosity, impair mass transfer and reduce sludge dewaterability. Copyright © 2015 Elsevier Ltd. All rights reserved.

  18. Processed foods and the consumer: additives, labeling, standards, and nutrition

    National Research Council Canada - National Science Library

    Packard, Vernal S

    1976-01-01

    ... supplements; and it brings together under one cover the health-related issues of food additives and nutrition. If I were to point to one objective of this work, it would be to guide student and consumer alike through the maze of food ingredients, regulations, and standards in order to make as clear as present knowledge allows the critical issues co...

  19. Processing of concentrated radioactive wastes into cement and bitumens following calcination

    International Nuclear Information System (INIS)

    Napravnik, J.; Sazavsky, P.; Ditl, P.; Prikryl, P.

    1985-01-01

    A brief characteristic is presented of the most frequently used processes of solidification of liquid radioactive wastes, viz., bituminization, cementation and their combination with calcination. The effect of individual parameters is assessed on the choice of the type of solidification process as is their importance in the actual process, in temporary storage, during transportation and under conditions of long-term storage. It has been found that a combination of the procedures could lead to a modular system of methods and equipment. This would allow to approach optimal solidification of wastes in the present period and to establish a research reserve for the development of more modern, economically advantageous and safer procedures. A rough estimate is made of the costs of the solidification of 1 m 3 of radioactive concentrate from the V-1 power plant at a production of 380 m 3 /year, this for the cementation-calcination and bituminization-calcination procedures. The said rough economic analysis only serves to identify the major operating components which have the greatest effect on the economic evaluation of the solidification procedures. (Z.M.)

  20. Improved hybridization of Fuzzy Analytic Hierarchy Process (FAHP) algorithm with Fuzzy Multiple Attribute Decision Making - Simple Additive Weighting (FMADM-SAW)

    Science.gov (United States)

    Zaiwani, B. E.; Zarlis, M.; Efendi, S.

    2018-03-01

    In this research, the improvement of hybridization algorithm of Fuzzy Analytic Hierarchy Process (FAHP) with Fuzzy Technique for Order Preference by Similarity to Ideal Solution (FTOPSIS) in selecting the best bank chief inspector based on several qualitative and quantitative criteria with various priorities. To improve the performance of the above research, FAHP algorithm hybridization with Fuzzy Multiple Attribute Decision Making - Simple Additive Weighting (FMADM-SAW) algorithm was adopted, which applied FAHP algorithm to the weighting process and SAW for the ranking process to determine the promotion of employee at a government institution. The result of improvement of the average value of Efficiency Rate (ER) is 85.24%, which means that this research has succeeded in improving the previous research that is equal to 77.82%. Keywords: Ranking and Selection, Fuzzy AHP, Fuzzy TOPSIS, FMADM-SAW.

  1. Merits and Demerits of Food Additives

    OpenAIRE

    YANG, Xuening; ZHAN, Yong

    2014-01-01

    Food additive is a double-edged sword. It has merits and demerits. Food additives have such merits as improving sensory properties of foods, preventing deterioration and extending the shelf life, increasing varieties of foods, enhancing convenience of foods, facilitating food processing, and satisfying other demands. However, excessive and illegal use of food additives will exert adverse influence on food security. Therefore, it is required to take proper measures to bring merits of food addi...

  2. Applications of Fiber-Reinforced Polymers in Additive Manufacturing

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Tosello, Guido

    2017-01-01

    Additive manufacturing technologies are these years entering the market of functional final parts. Initial research has been performed targeting the integration of fibers into additive manufactured plastic composites. Major advantages, among others, are for example increased tensile strength...... and Young's modulus. Key challenges in the field, as of now, are proper fiber placement, fiber seizing, an increased knowledge in the used materials and how they are applied into engineering solutions through proper control of the additive manufacturing process. The aim of this research is the improved...... understanding of fiber-reinforcement in additive manufacturing in terms of production and application. Vat polymerization and material extrusion techniques for composite additive manufacturing were investigated with respect of increasing adhesion between the matrix material and the fibers. Process optimization...

  3. AM Envelope. The potential of Additive Manufacturing for facade constructions

    Directory of Open Access Journals (Sweden)

    Holger Strauss

    2017-11-01

    Full Text Available This dissertation shows the potential of Additive Manufacturing (AM for the development of building envelopes: AM will change the way of designing facades, how we engineer and produce them. To achieve today’s demands from those future envelopes, we have to find new solutions. New technologies offer one possible way to do so. They open new approaches in designing, producing and processing building construction and facades. Finding the one capable of having big impact is difficult – Additive Manufacturing is one possible answer. The term ‘AM Envelope’ (Additive Manufacturing Envelope describes the transfer of this technology to the building envelope. Additive Fabrication is a building block that aids in developing the building envelope from a mere space enclosure to a dynamic building envelope. First beginnings of AM facade construction show up when dealing with relevant aspects like material consumption, mounting or part’s performance. From those starting points several parts of an existing post-and-beam façade system were optimized, aiming toward the implementation of AM into the production chain. Enhancements on all different levels of production were achieved: storing, producing, mounting and performance. AM offers the opportunity to manufacture facades ‘just in time’. It is no longer necessary to store or produce large numbers of parts in advance. Initial investment for tooling can be avoided, as design improvements can be realized within the dataset of the AM part. AM is based on ‘tool-less’ production, all parts can be further developed with every new generation. Producing tool-less also allows for new shapes and functional parts in small batch sizes – down to batch size one. The parts performance can be re-interpreted based on the demands within the system, not based on the limitations of conventional manufacturing. AM offers new ways of materializing the physical part around its function. It leads toward customized

  4. Additive manufacturing: state-of-the-art and application framework

    Directory of Open Access Journals (Sweden)

    Vinícius Picanço Rodrigues

    2017-09-01

    Full Text Available Additive manufacturing encompasses a class of production processes with increasing applications in different areas and supply chains. Due to its flexibility for production in small batches and the versatility of materials and geometries, this technology is recognized as being capable of revolutionizing the production processes as well as changing production strategies that are currently employed. However, there are different technologies under the generic label of additive manufacturing, materials and application areas with different requirements. Given the growing importance of additive manufacturing as a production process, and also considering the need to have a better insight into the potential applications for driving research and development efforts, this article presents a proposal of organization for additive manufacturing applications in seven areas. Additionally, the article provides a panorama of the current development stage of this technology, with a review of its major technological variants. The results presented aim to serve as a basis to support driving initiatives in additive manufacturing in companies, development agencies and research institutions.

  5. Additive operator-difference schemes splitting schemes

    CERN Document Server

    Vabishchevich, Petr N

    2013-01-01

    Applied mathematical modeling isconcerned with solving unsteady problems. This bookshows how toconstruct additive difference schemes to solve approximately unsteady multi-dimensional problems for PDEs. Two classes of schemes are highlighted: methods of splitting with respect to spatial variables (alternating direction methods) and schemes of splitting into physical processes. Also regionally additive schemes (domain decomposition methods)and unconditionally stable additive schemes of multi-component splitting are considered for evolutionary equations of first and second order as well as for sy

  6. Beryllium Project: developing in CDTN of uranium dioxide fuel pellets with addition of beryllium oxide to increase the thermal conductivity

    International Nuclear Information System (INIS)

    Ferreira, Ricardo Alberto Neto; Camarano, Denise das Merces; Miranda, Odair; Grossi, Pablo Andrade; Andrade, Antonio Santos; Queiroz, Carolinne Mol; Gonzaga, Mariana de Carvalho Leal

    2013-01-01

    Although the nuclear fuel currently based on pellets of uranium dioxide be very safe and stable, the biggest problem is that this material is not a good conductor of heat. This results in an elevated temperature gradient between the center and its lateral surface, which leads to a premature degradation of the fuel, which restricts the performance of the reactor, being necessary to change the fuel before its full utilization. An increase of only 5 to 10 percent in its thermal conductivity, would be a significant increase. An increase of 50 percent would be a great improvement. A project entitled 'Beryllium Project' was developed in CDTN - Centro de Desenvolvimento da Tecnologia Nuclear, which aimed to develop fuel pellets made from a mixture of uranium dioxide microspheres and beryllium oxide powder to obtain a better heat conductor phase, filling the voids between the microspheres to increase the thermal conductivity of the pellet. Increases in the thermal conductivity in the range of 8.6% to 125%, depending on the level of addition employed in the range of 1% to 14% by weight of beryllium oxide, were obtained. This type of fuel promises to be safer than current fuels, improving the performance of the reactor, in addition to last longer, resulting in great savings. (author)

  7. Evaluation of a safer male circumcision training programme for traditional surgeons and nurses in the Eastern Cape, South Africa.

    Science.gov (United States)

    Peltzer, Karl; Nqeketo, Ayanda; Petros, George; Kanta, Xola

    2008-06-18

    Training designed to improve circumcision knowledge, attitude and practice was delivered over 5 days to 34 traditional surgeons and 49 traditional nurses in the Eastern Cape, South Africa. Training included the following topics: initiation rites; statutory regulation of traditional male circumcision and initiation into Manhood (TCIM); structure and function of the male sex organs; procedure of safe circumcision, infection control; sexually transmitted infections (STIs); HIV/AIDS; infection control measures; aftercare of the initiate including after care of the circumcision wound and initiate as a whole; detection and early management of common complications of circumcision; nutrition and fluid management; code of conduct and ethics; and sexual health education. The evaluation of the training consisted of a prospective assessment of knowledge and attitude immediately prior to and after training. Significant improvement in knowledge and/or attitudes was observed in legal aspects, STI, HIV and environmental aspects, attitudes in terms of improved collaboration with biomedical health care providers, normal and abnormal anatomy and physiology, sexually transmitted infections and including HIV, circumcision practice and aftercare of initiates. We concluded that safer circumcision training can be successfully delivered to traditional surgeons and nurses.

  8. Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

    Energy Technology Data Exchange (ETDEWEB)

    Gesta, E. [Ingénierie des Matériaux Polymères - UMR CNRS 5223, Université de Lyon - Université Lyon 1, Bâtiment POLYTECH Lyon - 15 boulevard Latarjet, 69622, Villeurbanne (France); Intelligent Insect Control, 118 Chemin des Alouettes, Castelnau-le-Lez, 34170 (France); Skovmand, O., E-mail: osk@insectcontrol.net [Intelligent Insect Control, 118 Chemin des Alouettes, Castelnau-le-Lez, 34170 (France); Espuche, E., E-mail: eliane.espuche@univ-lyon1.fr; Fulchiron, R., E-mail: rene.fulchiron@univ-lyon1.fr [Ingénierie des Matériaux Polymères - UMR CNRS 5223, Université de Lyon - Université Lyon 1, Bâtiment POLYTECH Lyon - 15 boulevard Latarjet, 69622, Villeurbanne (France)

    2015-12-17

    The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives’ ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration.

  9. Migration of additive molecules in a polymer filament obtained by melt spinning: Influence of the fiber processing steps

    International Nuclear Information System (INIS)

    Gesta, E.; Skovmand, O.; Espuche, E.; Fulchiron, R.

    2015-01-01

    The purpose of this study is to understand the influence of the yarn processing on the migration of additives molecules, especially insecticide, within polyethylene (PE) yarns. Yarns were manufactured in the laboratory focusing on three key-steps (spinning, post-stretching and heat-setting). Influence of each step on yarn properties was investigated using tensile tests, differential scanning calorimetry and wide-angle X-ray diffraction. The post-stretching step was proved to be critical in defining yarn mechanical and structural properties. Although a first orientation of polyethylene crystals was induced during spinning, the optimal orientation was only reached by post-stretching. The results also showed that the heat-setting did not significantly change these properties. The presence of additives crystals at the yarn surface was evidenced by scanning-electron microscopy. These studies performed at each yarn production step allowed a detailed analysis of the additives’ ability to migrate. It is concluded that while post-stretching decreased the migration rate, heat-setting seems to boost this migration

  10. Laser-Based Additive Manufacturing of Zirconium

    Directory of Open Access Journals (Sweden)

    Himanshu Sahasrabudhe

    2018-03-01

    Full Text Available Additive manufacturing of zirconium is attempted using commercial Laser Engineered Net Shaping (LENSTM technique. A LENSTM-based approach towards processing coatings and bulk parts of zirconium, a reactive metal, aims to minimize the inconvenience of traditional metallurgical practices of handling and processing zirconium-based parts that are particularly suited to small volumes and one-of-a-kind parts. This is a single-step manufacturing approach for obtaining near net shape fabrication of components. In the current research, Zr metal powder was processed in the form of coating on Ti6Al4V alloy substrate. Scanning electron microscopy (SEM and energy dispersive spectroscopy (EDS as well as phase analysis via X-ray diffraction (XRD were studied on these coatings. In addition to coatings, bulk parts were also fabricated using LENS™ from Zr metal powders, and measured part accuracy.

  11. Streamlined Approach for Environmental Restoration Plan for Corrective Action Unit 116: Area 25 Test Cell C Facility, Nevada Test Site, Nevada, Revision 1

    International Nuclear Information System (INIS)

    2008-01-01

    This Streamlined Approach for Environmental Restoration (SAFER) Plan identifies the activities required for the closure of Corrective Action Unit (CAU) 116, Area 25 Test Cell C Facility. The Test Cell C (TCC) Facility is located in Area 25 of the Nevada Test Site (NTS) approximately 25 miles northwest of Mercury, Nevada (Figure 1). CAU 116 is currently listed in Appendix III of the Federal Facility Agreement and Consent Order (FFACO) of 1996 (as amended February 2008) and consists of two Corrective Action Sites (CASs): (1) CAS 25-23-20, Nuclear Furnace Piping; and (2) CAS 25-41-05, Test Cell C Facility. CAS 25-41-05 is described in the FFACO as the TCC Facility but actually includes Building 3210 and attached concrete shield wall only. CAU 116 will be closed by demolishing Building 3210, the attached concrete shield wall, and the nuclear furnace piping. In addition, as a best management practice (BMP), Building 3211 (moveable shed) will be demolished due to its close proximity to Building 3210. This will aid in demolition and disposal operations. Radiological surveys will be performed on the demolition debris to determine the proper disposal pathway. As much of the demolition debris as space allows will be placed into the Building 3210 basement structure. After filling to capacity with demolition debris, the basement structure will be mounded or capped and closed with administrative controls. Prior to beginning demolition activities and according to an approved Sampling and Analysis Plan (SAP), representative sampling of surface areas that are known, suspected, or have the potential to contain hazardous constituents such as lead or polychlorinated biphenyls (PCBs) will be performed throughout all buildings and structures. Sections 2.3.2, 4.2.2.2, 4.2.2.3, 4.3, and 6.2.6.1 address the methodologies employed that assure the solid debris placed in the basement structure will not contain contaminants of concern (COCs) above hazardous waste levels. The anticipated post

  12. Additive Manufacturing in the Marine Corps

    Science.gov (United States)

    2015-06-01

    TERMS additive manufacturing, 3D printing, improving logistics 15. NUMBER OF PAGES 123 16. PRICE CODE 17. SECURITY CLASSIFICATION OF REPORT...One such method is ultrasonic agglomeration. The process produces compact snack items that are nutrient-dense and shelf-stable. Currently Army...possess outdated technology. Additionally, prices for the printers are dropping significantly.202 Therefore, the Marine Corps will not only have outdated

  13. Radiation processing for value addition in fish and fishery products

    International Nuclear Information System (INIS)

    Bandekar, J.R.; Karani, M.; Kakatkar, A.S.; Sharma, A.

    2009-01-01

    Fish is highly nutritious as it contains easily digestible proteins and nutritionally important vitamins and polyunsaturated fatty acids. However, due to high ambient temperature in tropical countries, fish is spoiled rapidly. Spoilage of fish during transportation and storage amounting to about 30% of the catch results in heavy economic losses. The microbiological hazard related to the presence of food-borne pathogens is also common in both marine and aqua-cultured fish and shellfish. In dried products (moisture content, < 20%) insects are mainly responsible for the loss of quality during storage. Radiation processing can play a major role in ensuring security and safety of fish and fishery products by reducing post-harvest losses and eliminating pathogenic microorganisms. Being a 'cold process' the technology helps in retaining the quality of fishery products in 'as is' condition. (author)

  14. Redox shuttles for safer lithium-ion batteries

    International Nuclear Information System (INIS)

    Chen, Zonghai; Qin, Yan; Amine, Khalil

    2009-01-01

    Overcharge protection is not only critical for preventing the thermal runaway of lithium-ion batteries during operation, but also important for automatic capacity balancing during battery manufacturing and repair. A redox shuttle is an electrolyte additive that can be used as intrinsic overcharge protection mechanism to enhance the safety characteristics of lithium-ion batteries. The advances on stable redox shuttles are briefly reviewed. Fundamental studies for designing stable redox shuttles are also discussed.

  15. Continuous Digital Light Processing (cDLP): Highly Accurate Additive Manufacturing of Tissue Engineered Bone Scaffolds.

    Science.gov (United States)

    Dean, David; Jonathan, Wallace; Siblani, Ali; Wang, Martha O; Kim, Kyobum; Mikos, Antonios G; Fisher, John P

    2012-03-01

    Highly accurate rendering of the external and internal geometry of bone tissue engineering scaffolds effects fit at the defect site, loading of internal pore spaces with cells, bioreactor-delivered nutrient and growth factor circulation, and scaffold resorption. It may be necessary to render resorbable polymer scaffolds with 50 μm or less accuracy to achieve these goals. This level of accuracy is available using Continuous Digital Light processing (cDLP) which utilizes a DLP(®) (Texas Instruments, Dallas, TX) chip. One such additive manufacturing device is the envisionTEC (Ferndale, MI) Perfactory(®). To use cDLP we integrate a photo-crosslinkable polymer, a photo-initiator, and a biocompatible dye. The dye attenuates light, thereby limiting the depth of polymerization. In this study we fabricated scaffolds using the well-studied resorbable polymer, poly(propylene fumarate) (PPF), titanium dioxide (TiO(2)) as a dye, Irgacure(®) 819 (BASF [Ciba], Florham Park, NJ) as an initiator, and diethyl fumarate as a solvent to control viscosity.

  16. Anticonvulsants Teratogenic Mechanism Involves Alteration of Bioelectrically-controlled Processes in the Embryo. A hypothesis

    Science.gov (United States)

    Hernández-Díaz, Sonia; Levin, Michael

    2014-01-01

    Maternal use of anticonvulsants during the first trimester of pregnancy has been associated with an elevated risk of major congenital malformations in the offspring. Whether the increased risk is caused by the specific pharmacological mechanisms of certain anticonvulsants, the underlying epilepsy, or common genetic or environmental risk factors shared by epilepsy and malformations is controversial. We hypothesize that anticonvulsant therapies during pregnancy that attain more successful inhibition of neurotransmission might lead to both better seizure control in the mother and stronger alteration of bioelectrically-controlled processes in the embryo that result in structural malformations. If our theory were correct, development of pharmaceuticals that do not alter cell resting transmembrane voltage levels could result in safer drugs. PMID:24815983

  17. Transgenic Bacillus thuringiensis (Bt rice is safer to aquatic ecosystems than its non-transgenic counterpart.

    Directory of Open Access Journals (Sweden)

    Guangsheng Li

    Full Text Available Rice lines genetically modified with the crystal toxin genes from Bacillus thuringiensis (Bt have experienced rapid development, with biosafety certificates for two Bt rice lines issued in 2009. There has still been no commercial release of these lines yet due to public concerns about human health and environmental risks. Some studies confirmed that Bt rice was as safe as conventional rice to non-target organisms when pesticides were not applied, however, pesticides are still required in Bt rice to control non-lepidopteran pests. In this study, we assessed the environmental effects of two Bt rice lines expressing either the cry1Ab/1Ac or cry2A genes, respectively, by using zooplanktons as indicator species under normal field management practices using pesticides when required. In the whole rice growing season, non-Bt rice was sprayed 5 times while Bt rice was sprayed 2 times, which ensured both rice achieved a normal yield. Field investigations showed that rice type (Bt and non-Bt significantly influenced zooplankton abundance and diversity, which were up to 95% and 80% lower in non-Bt rice fields than Bt rice fields. Laboratory rearing showed that water from non-Bt rice fields was significantly less suitable for the survival and reproduction of Daphnia magna and Paramecium caudatum in comparison with water from Bt rice fields. Higher pesticide residues were detected in the water from non-Bt than Bt rice fields, accounting for the bad performance of zooplankton in non-Bt field water. Our results demonstrate that Bt rice is safer to aquatic ecosystems than non-Bt rice, and its commercialization will be beneficial for biodiversity restoration in rice-based ecosystems.

  18. Understanding international road safety disparities: Why is Australia so much safer than the United States?

    Science.gov (United States)

    Marshall, Wesley E

    2018-02-01

    Despite similarities to the US in terms of transportation, land use, and culture, Australia kills 5.3 people per 100,000 population on the roads each year, as compared to the US rate of 12.4. Similar trends hold when accounting for distance driven and the number of registered cars. This paper seeks to understand what is behind the road safety disparities between these two countries. The results suggest that a number of inter-related factors seem to play a role in the better road safety outcomes of Australia as compared to the US. This includes Australia's strategies related to seat belt usage and impaired driving as well as their efforts to help curb vehicle speeds and reduce exposure. Design-related differences include a much greater reliance on roundabouts and narrower street cross-sections as well as guidelines that encourage self-enforcing roads. Policy-related differences include stronger and more extensive enforcement programs, restrictive licensing programs, and higher driving costs. Combined with a more urban population and multimodal infrastructure, Australia tends to discourage driving mileage and exposure while encouraging safer modes of transportation such as transit, at least more so than in most of the US. Australia also enacted their version of Vision Zero - called the Safe System Approach - more than a decade before similar policies began cropping up in US cities. While it is difficult to attribute recent road safety successes to any specific policy, Australia continues to expand their lead on the US in terms of safety outcomes and is a road safety example worthy of consideration. Copyright © 2017 Elsevier Ltd. All rights reserved.

  19. Additive manufacturing of reflective optics: evaluating finishing methods

    Science.gov (United States)

    Leuteritz, G.; Lachmayer, R.

    2018-02-01

    Individually shaped light distributions become more and more important in lighting technologies and thus the importance of additively manufactured reflectors increases significantly. The vast field of applications ranges from automotive lighting to medical imaging and bolsters the statement. However, the surfaces of additively manufactured reflectors suffer from insufficient optical properties even when manufactured using optimized process parameters for the Selective Laser Melting (SLM) process. Therefore post-process treatments of reflectors are necessary in order to further enhance their optical quality. This work concentrates on the effectiveness of post-process procedures for reflective optics. Based on already optimized aluminum reflectors, which are manufactured with a SLM machine, the parts are differently machined after the SLM process. Selected finishing methods like laser polishing, sputtering or sand blasting are applied and their effects quantified and compared. The post-process procedures are investigated on their impact on surface roughness and reflectance as well as geometrical precision. For each finishing method a demonstrator will be created and compared to a fully milled sample and among themselves. Ultimately, guidelines are developed in order to figure out the optimal treatment of additively manufactured reflectors regarding their optical and geometrical properties. Simulations of the light distributions will be validated with the developed demonstrators.

  20. The Evolution of Process Safety: Current Status and Future Direction.

    Science.gov (United States)

    Mannan, M Sam; Reyes-Valdes, Olga; Jain, Prerna; Tamim, Nafiz; Ahammad, Monir

    2016-06-07

    The advent of the industrial revolution in the nineteenth century increased the volume and variety of manufactured goods and enriched the quality of life for society as a whole. However, industrialization was also accompanied by new manufacturing and complex processes that brought about the use of hazardous chemicals and difficult-to-control operating conditions. Moreover, human-process-equipment interaction plus on-the-job learning resulted in further undesirable outcomes and associated consequences. These problems gave rise to many catastrophic process safety incidents that resulted in thousands of fatalities and injuries, losses of property, and environmental damages. These events led eventually to the necessity for a gradual development of a new multidisciplinary field, referred to as process safety. From its inception in the early 1970s to the current state of the art, process safety has come to represent a wide array of issues, including safety culture, process safety management systems, process safety engineering, loss prevention, risk assessment, risk management, and inherently safer technology. Governments and academic/research organizations have kept pace with regulatory programs and research initiatives, respectively. Understanding how major incidents impact regulations and contribute to industrial and academic technology development provides a firm foundation to address new challenges, and to continue applying science and engineering to develop and implement programs to keep hazardous materials within containment. Here the most significant incidents in terms of their impact on regulations and the overall development of the field of process safety are described.

  1. Process Recovery after CaO Addition Due to Granule Formation in a CSTR Co-Digester—A Tool to Influence the Composition of the Microbial Community and Stabilize the Process?

    Science.gov (United States)

    Liebrich, Marietta; Kleyböcker, Anne; Kasina, Monika; Miethling-Graff, Rona; Kassahun, Andrea; Würdemann, Hilke

    2016-01-01

    The composition, structure and function of granules formed during process recovery with calcium oxide in a laboratory-scale fermenter fed with sewage sludge and rapeseed oil were studied. In the course of over-acidification and successful process recovery, only minor changes were observed in the bacterial community of the digestate, while granules appeared during recovery. Fluorescence microscopic analysis of the granules showed a close spatial relationship between calcium and oil and/or long chain fatty acids. This finding further substantiated the hypothesis that calcium precipitated with carbon of organic origin and reduced the negative effects of overloading with oil. Furthermore, the enrichment of phosphate minerals in the granules was shown, and molecular biological analyses detected polyphosphate-accumulating organisms as well as methanogenic archaea in the core. Organisms related to Methanoculleus receptaculi were detected in the inner zones of a granule, whereas they were present in the digestate only after process recovery. This finding indicated more favorable microhabitats inside the granules that supported process recovery. Thus, the granule formation triggered by calcium oxide addition served as a tool to influence the composition of the microbial community and to stabilize the process after overloading with oil. PMID:27681911

  2. Process Recovery after CaO Addition Due to Granule Formation in a CSTR Co-Digester-A Tool to Influence the Composition of the Microbial Community and Stabilize the Process?

    Science.gov (United States)

    Liebrich, Marietta; Kleyböcker, Anne; Kasina, Monika; Miethling-Graff, Rona; Kassahun, Andrea; Würdemann, Hilke

    2016-03-17

    The composition, structure and function of granules formed during process recovery with calcium oxide in a laboratory-scale fermenter fed with sewage sludge and rapeseed oil were studied. In the course of over-acidification and successful process recovery, only minor changes were observed in the bacterial community of the digestate, while granules appeared during recovery. Fluorescence microscopic analysis of the granules showed a close spatial relationship between calcium and oil and/or long chain fatty acids. This finding further substantiated the hypothesis that calcium precipitated with carbon of organic origin and reduced the negative effects of overloading with oil. Furthermore, the enrichment of phosphate minerals in the granules was shown, and molecular biological analyses detected polyphosphate-accumulating organisms as well as methanogenic archaea in the core. Organisms related to Methanoculleus receptaculi were detected in the inner zones of a granule, whereas they were present in the digestate only after process recovery. This finding indicated more favorable microhabitats inside the granules that supported process recovery. Thus, the granule formation triggered by calcium oxide addition served as a tool to influence the composition of the microbial community and to stabilize the process after overloading with oil.

  3. Process Recovery after CaO Addition Due to Granule Formation in a CSTR Co-Digester—A Tool to Influence the Composition of the Microbial Community and Stabilize the Process?

    Directory of Open Access Journals (Sweden)

    Marietta Liebrich

    2016-03-01

    Full Text Available The composition, structure and function of granules formed during process recovery with calcium oxide in a laboratory-scale fermenter fed with sewage sludge and rapeseed oil were studied. In the course of over-acidification and successful process recovery, only minor changes were observed in the bacterial community of the digestate, while granules appeared during recovery. Fluorescence microscopic analysis of the granules showed a close spatial relationship between calcium and oil and/or long chain fatty acids. This finding further substantiated the hypothesis that calcium precipitated with carbon of organic origin and reduced the negative effects of overloading with oil. Furthermore, the enrichment of phosphate minerals in the granules was shown, and molecular biological analyses detected polyphosphate-accumulating organisms as well as methanogenic archaea in the core. Organisms related to Methanoculleus receptaculi were detected in the inner zones of a granule, whereas they were present in the digestate only after process recovery. This finding indicated more favorable microhabitats inside the granules that supported process recovery. Thus, the granule formation triggered by calcium oxide addition served as a tool to influence the composition of the microbial community and to stabilize the process after overloading with oil.

  4. Predicting Color Output of Additive Manufactured Parts

    DEFF Research Database (Denmark)

    Eiríksson, Eyþór Rúnar; Pedersen, David Bue; Aanæs, Henrik

    2015-01-01

    In this paper we address the colorimetric performance of a multicolor additive manufacturing process. A method on how to measure and characterize color performance of said process is presented. Furthermore, a method on predicting the color output is demonstrated, allowing for previsualization...

  5. Effects of Processing Parameters on Surface Roughness of Additive Manufactured Ti-6Al-4V via Electron Beam Melting

    Science.gov (United States)

    Sin, Wai Jack; Nai, Mui Ling Sharon; Wei, Jun

    2017-01-01

    As one of the powder bed fusion additive manufacturing technologies, electron beam melting (EBM) is gaining more and more attention due to its near-net-shape production capacity with low residual stress and good mechanical properties. These characteristics also allow EBM built parts to be used as produced without post-processing. However, the as-built rough surface introduces a detrimental influence on the mechanical properties of metallic alloys. Thereafter, understanding the effects of processing parameters on the part’s surface roughness, in turn, becomes critical. This paper has focused on varying the processing parameters of two types of contouring scanning strategies namely, multispot and non-multispot, in EBM. The results suggest that the beam current and speed function are the most significant processing parameters for non-multispot contouring scanning strategy. While for multispot contouring scanning strategy, the number of spots, spot time, and spot overlap have greater effects than focus offset and beam current. The improved surface roughness has been obtained in both contouring scanning strategies. Furthermore, non-multispot contouring scanning strategy gives a lower surface roughness value and poorer geometrical accuracy than the multispot counterpart under the optimized conditions. These findings could be used as a guideline for selecting the contouring type used for specific industrial parts that are built using EBM. PMID:28937638

  6. Process-Structure-Property Relationships for 316L Stainless Steel Fabricated by Additive Manufacturing and Its Implication for Component Engineering

    Science.gov (United States)

    Yang, Nancy; Yee, J.; Zheng, B.; Gaiser, K.; Reynolds, T.; Clemon, L.; Lu, W. Y.; Schoenung, J. M.; Lavernia, E. J.

    2017-04-01

    We investigate the process-structure-property relationships for 316L stainless steel prototyping utilizing 3-D laser engineered net shaping (LENS), a commercial direct energy deposition additive manufacturing process. The study concluded that the resultant physical metallurgy of 3-D LENS 316L prototypes is dictated by the interactive metallurgical reactions, during instantaneous powder feeding/melting, molten metal flow and liquid metal solidification. The study also showed 3-D LENS manufacturing is capable of building high strength and ductile 316L prototypes due to its fine cellular spacing from fast solidification cooling, and the well-fused epitaxial interfaces at metal flow trails and interpass boundaries. However, without further LENS process control and optimization, the deposits are vulnerable to localized hardness variation attributed to heterogeneous microstructure, i.e., the interpass heat-affected zone (HAZ) from repetitive thermal heating during successive layer depositions. Most significantly, the current deposits exhibit anisotropic tensile behavior, i.e., lower strain and/or premature interpass delamination parallel to build direction (axial). This anisotropic behavior is attributed to the presence of interpass HAZ, which coexists with flying feedstock inclusions and porosity from incomplete molten metal fusion. The current observations and findings contribute to the scientific basis for future process control and optimization necessary for material property control and defect mitigation.

  7. Sewage sludge additive

    Science.gov (United States)

    Kalvinskas, J. J.; Mueller, W. A.; Ingham, J. D. (Inventor)

    1980-01-01

    The additive is for a raw sewage treatment process of the type where settling tanks are used for the purpose of permitting the suspended matter in the raw sewage to be settled as well as to permit adsorption of the dissolved contaminants in the water of the sewage. The sludge, which settles down to the bottom of the settling tank is extracted, pyrolyzed and activated to form activated carbon and ash which is mixed with the sewage prior to its introduction into the settling tank. The sludge does not provide all of the activated carbon and ash required for adequate treatment of the raw sewage. It is necessary to add carbon to the process and instead of expensive commercial carbon, coal is used to provide the carbon supplement.

  8. Model Additional Protocol

    International Nuclear Information System (INIS)

    Rockwood, Laura

    2001-01-01

    Since the end of the cold war a series of events has changed the circumstances and requirements of the safeguards system. The discovery of a clandestine nuclear weapons program in Iraq, the continuing difficulty in verifying the initial report of Democratic People's Republic of Korea upon entry into force of their safeguards agreement, and the decision of the South African Government to give up its nuclear weapons program and join the Treaty on the Non-Proliferation of Nuclear Weapons have all played a role in an ambitious effort by IAEA Member States and the Secretariat to strengthen the safeguards system. A major milestone in this effort was reached in May 1997 when the IAEA Board of Governors approved a Model Protocol Additional to Safeguards Agreements. The Model Additional Protocol was negotiated over a period of less than a year by an open-ended committee of the Board involving some 70 Member States and two regional inspectorates. The IAEA is now in the process of negotiating additional protocols, State by State, and implementing them. These additional protocols will provide the IAEA with rights of access to information about all activities related to the use of nuclear material in States with comprehensive safeguards agreements and greatly expanded physical access for IAEA inspectors to confirm or verify this information. In conjunction with this, the IAEA is working on the integration of these measures with those provided for in comprehensive safeguards agreements, with a view to maximizing the effectiveness and efficiency, within available resources, the implementation of safeguards. Details concerning the Model Additional Protocol are given. (author)

  9. Safer environment makes sense for all.

    Science.gov (United States)

    Frith, Sue

    2011-06-01

    Sue Frith, deputy head of the NHS Security Management Service (NHS SMS), explains the organisation's important role in advising, and supporting, security staff at NHS hospitals in dealing with incidents ranging from verbal abuse to serious violence and aggression. Arguing that security in the NHS is "everyone's business", she explains both a range of processes and initiatives,already in place to safeguard people and assets, and discusses recent developments, such as a new incident reporting website, designed to help keep patients, staff, visitors, and property, at healthcare facilities safe and secure.

  10. Powder Characterization and Optimization for Additive Manufacturing

    NARCIS (Netherlands)

    Cordova, Laura; Campos, Mónica; Tinga, Tiedo

    2017-01-01

    Achieving the optimal quality for Additive Manufactured (AM) parts does not only depend on setting the right process parameters. Material feedstock also plays an important role when aiming for high performance products. The metal AM processes that are most applicable to industry, Powder Bed Fusion

  11. Alteration of bioelectrically-controlled processes in the embryo: a teratogenic mechanism for anticonvulsants.

    Science.gov (United States)

    Hernández-Díaz, Sonia; Levin, Michael

    2014-08-01

    Maternal use of anticonvulsants during the first trimester of pregnancy has been associated with an elevated risk of major congenital malformations in the offspring. Whether the increased risk is caused by the specific pharmacological mechanisms of certain anticonvulsants, the underlying epilepsy, or common genetic or environmental risk factors shared by epilepsy and malformations has been controversial. We hypothesize that anticonvulsant therapies during pregnancy that attain more successful inhibition of neurotransmission might lead to both better seizure control in the mother and stronger alteration of bioelectrically-controlled processes in the embryo that result in structural malformations. We propose that development of pharmaceuticals that do not alter cell resting transmembrane voltage levels could result in safer drugs. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. Fuel and Additive Characterization for HCCI Combustion

    International Nuclear Information System (INIS)

    Aceves, S M; Flowers, D; Martinez-Frias, J; Espinosa-Loza, F; Pitz, W J; Dibble, R

    2003-01-01

    This paper shows a numerical evaluation of fuels and additives for HCCl combustion. First, a long list of candidate HCCl fuels is selected. For all the fuels in the list, operating conditions (compression ratio, equivalence ratio and intake temperature) are determined that result in optimum performance under typical operation for a heavy-duty engine. Fuels are also characterized by presenting Log(p)-Log(T) maps for multiple fuels under HCCl conditions. Log(p)-Log(T) maps illustrate important processes during HCCl engine operation, including compression, low temperature heat release and ignition. Log(p)-Log(T) diagrams can be used for visualizing these processes and can be used as a tool for detailed analysis of HCCl combustion. The paper also includes a ranking of many potential additives. Experiments and analyses have indicated that small amounts (a few parts per million) of secondary fuels (additives) may considerably affect HCCl combustion and may play a significant role in controlling HCCl combustion. Additives are ranked according to their capability to advance HCCl ignition. The best additives are listed and an explanation of their effect on HCCl combustion is included

  13. Material Database for Additive Manufacturing Techniques

    Science.gov (United States)

    2017-12-01

    components in the field. II. BACKGROUND Additive manufacturing is a rapidly maturing process by which digital 3-D design data are used to build up...improves readiness by offering on-demand low-rate production [8, 9]. 3-D printing also enables rapid design iterations and complexity, which improve...abundant in additive manufacturing , allowing design freedom that is only limited by the material strength requirements. A set of eight conductive

  14. Utilization of curve offsets in additive manufacturing

    Science.gov (United States)

    Haseltalab, Vahid; Yaman, Ulas; Dolen, Melik

    2018-05-01

    Curve offsets are utilized in different fields of engineering and science. Additive manufacturing, which lately becomes an explicit requirement in manufacturing industry, utilizes curve offsets widely. One of the necessities of offsetting is for scaling which is required if there is shrinkage after the fabrication or if the surface quality of the resulting part is unacceptable. Therefore, some post-processing is indispensable. But the major application of curve offsets in additive manufacturing processes is for generating head trajectories. In a point-wise AM process, a correct tool-path in each layer can reduce lots of costs and increase the surface quality of the fabricated parts. In this study, different curve offset generation algorithms are analyzed to show their capabilities and disadvantages through some test cases and improvements on their drawbacks are suggested.

  15. [Safer operating theatre: easier said than done].

    Science.gov (United States)

    Kalkman, C J

    2008-10-18

    The Netherlands Health Care Inspectorate recently changed its approach to quality of care and patient safety from a reactive to a firmly proactive style. In two reports, the current perioperative processes in Dutch hospitals were scrutinised. Despite a highly-motivated workforce, the inspectorate detected a lack of standardisation, incomplete or inaccessible patient data, poor adherence to hygiene standards and gaps during transfer of care in both the preoperative and intraoperative stages ofsurgery. The inspectorate mandates rapid implementation of various new patient safety approaches, including the use of checklists, 'time-outs' before the start of surgery, double checking of intravenous drugs and improved compliance with hygiene standards, as well as a strict definition of roles and responsibilities of team members. Implementation will require major changes within the processes and culture of operating theatres in Dutch hospitals. Such a change is unlikely to be completed within the short timeframe allowed by the inspectorate.

  16. Improvement of phenolic antioxidants and quality characteristics of virgin olive oil with the addition of enzymes and nitrogen during olive paste processing

    Energy Technology Data Exchange (ETDEWEB)

    Inconomou, D.; Arapoglou, D.; Israilides, C.

    2010-07-01

    The evolution of phenolic compounds and their contribution to the quality characteristics in virgin olive oil during fruit processing was studied with the addition of a combination of various commercial enzymes containing pectinases, polygalacturonases, cellulase and {beta}-glucanase with or without nitrogen flush. Olive fruits (Olea europaea, L.) of the cultivar Megaritiki, at the semi black pigmentation stage of maturity, were used in a 3-phase extraction system in an experiment at industrial scale. The addition of enzymes in the olive paste during processing increased the total phenol and ortho-diphenol contents, as well as some simple phenolic compounds (3,4-DHPEA, p-HPEA) and the secoiridoid derivatives (3,4-DHPEA-EDA and 3,4-DHPEAEA) in olive oil and therefore improved its oxidative stability. Furthermore, enzyme treatment ameliorated the quality parameters of the produced olive oil (acidity and peroxide value) and their sensory attributes. The use of additional N{sub 2} flush with the enzyme treatments did not improve the quality parameters of olive oil any further; however it did not affect the concentration of individual and total sterols or most of the fatty acid composition. Consequently, olive paste treatment with enzymes not only improved the quality characteristics of olive oil and enhanced the overall organoleptic quality, but also increased the olive oil yield. (Author) 33 refs.

  17. BWR zinc addition Sourcebook

    International Nuclear Information System (INIS)

    Garcia, Susan E.; Giannelli, Joseph F.; Jarvis, Alfred J.

    2014-01-01

    Boiling Water Reactors (BWRs) have been injecting zinc into the primary coolant via the reactor feedwater system for over 25 years for the purpose of controlling primary system radiation fields. The BWR zinc injection process has evolved since the initial application at the Hope Creek Nuclear Station in 1986. Key transitions were from the original natural zinc oxide (NZO) to depleted zinc oxide (DZO), and from active zinc injection of a powdered zinc oxide slurry (pumped systems) to passive injection systems (zinc pellet beds). Zinc addition has continued through various chemistry regimes changes, from normal water chemistry (NWC) to hydrogen water chemistry (HWC) and HWC with noble metals (NobleChem™) for mitigation of intergranular stress corrosion cracking (IGSCC) of reactor internals and primary system piping. While past reports published by the Electric Power Research Institute (EPRI) document specific industry experience related to these topics, the Zinc Sourcebook was prepared to consolidate all of the experience gained over the past 25 years. The Zinc Sourcebook will benefit experienced BWR Chemistry, Operations, Radiation Protection and Engineering personnel as well as new people entering the nuclear power industry. While all North American BWRs implement feedwater zinc injection, a number of other BWRs do not inject zinc. This Sourcebook will also be a valuable resource to plants considering the benefits of zinc addition process implementation, and to gain insights on industry experience related to zinc process control and best practices. This paper presents some of the highlights from the Sourcebook. (author)

  18. Radiation processing for value addition to spices and condiments

    International Nuclear Information System (INIS)

    More, Varsha S.; Parte, Madan N.; Gautam, Satyendra; Sharma, Arun

    2009-01-01

    Both major and minor Indian spices and their blends were found to have significant high level of bacterial and fungal load. Radiation processing at 10 kGy dose was found to be effective for hygienization of spices and condiments without affecting their flavor and other quality attributes. Inter and Intra country transportation studies confirmed the retention of spice quality following irradiation, transportation and storage. A safe storage period was also determined for sambar powder packaged in metallised laminate pouch, which turned out to be 20 months under ambient storage conditions. Some spices were also found to have radioprotective effect. (author)

  19. InP/ZnS as a safer alternative to CdSe/ZnS core/shell quantum dots: in vitro and in vivo toxicity assessment

    Science.gov (United States)

    Brunetti, Virgilio; Chibli, Hicham; Fiammengo, Roberto; Galeone, Antonio; Malvindi, Maria Ada; Vecchio, Giuseppe; Cingolani, Roberto; Nadeau, Jay L.; Pompa, Pier Paolo

    2012-12-01

    We show that water soluble InP/ZnS core/shell QDs are a safer alternative to CdSe/ZnS QDs for biological applications, by comparing their toxicity in vitro (cell culture) and in vivo (animal model Drosophila). By choosing QDs with comparable physical and chemical properties, we find that cellular uptake and localization are practically identical for these two nanomaterials. Toxicity of CdSe/ZnS QDs appears to be related to the release of poisonous Cd2+ ions and indeed we show that there is leaching of Cd2+ ions from the particle core despite the two-layer ZnS shell. Since an almost identical amount of In(iii) ions is observed to leach from the core of InP/ZnS QDs, their very low toxicity as revealed in this study hints at a much lower intrinsic toxicity of indium compared to cadmium.

  20. Bacteria-eating virus approved as food additive.

    Science.gov (United States)

    Bren, Linda

    2007-01-01

    Not all viruses harm people. The Food and Drug Administration has approved a mixture of viruses as a food additive to protect people. The additive can be used in processing plants for spraying onto ready-to-eat meat and poultry products to protect consumers from the potentially life-threatening bacterium Listeria monocytogenes (L. monocytogenes).