Performance Assessment and analysis of national building codes with fire safety in all wards of a hospital

Directory of Open Access Journals (Sweden)

M. Mahdinia

2009-04-01

Full Text Available Background and aimsAIDS as a re-emergent disease and Viral hepatitis (B and C as one of thBackground and objective: Fire safety is an important problem in hospitals. Movement less, lack of awareness and special situation of residents are the reasons of this subject. In more countries such as Iran, fire protection regulations have compiled within the framework of national building codes. Current building codes don't create sufficient safety for patient in the hospitals in different situations and more of the advanced countries in the world effort to establish building code, base  on performance. This study to be accomplished with this goal that determination of fire risk level in the wards of a hospital and survey the efficiency of the national building codes. Methodsfire risk assesses is done, using "engineering fire risk assessment method" with the checklist for Data gathering. In this manner, risk calculate in all compartments and in the next  stage for survey the effect of building codes, with this supposition that all compartment is  conforming to building code requirement, risk level calculate in two situation.Resultsthe results of present study reveals that, risk level in all wards is more than one and even though risk less than one is acceptable, consequently minimum of safely situations didn't  produce in most wards. The results show the national building code in the different conditions  don't have appropriate efficient for creation of suitable safety. Conclusionin order to access to a fire safety design with sufficient efficiency, suitable selection is use of risk assessment based on, design methods.

Office of Codes and Standards resource book. Section 1, Building energy codes and standards

Energy Technology Data Exchange (ETDEWEB)

Hattrup, M.P.

1995-01-01

The US Department of Energy`s (DOE`s) Office of Codes and Standards has developed this Resource Book to provide: A discussion of DOE involvement in building codes and standards; a current and accurate set of descriptions of residential, commercial, and Federal building codes and standards; information on State contacts, State code status, State building construction unit volume, and State needs; and a list of stakeholders in the building energy codes and standards arena. The Resource Book is considered an evolving document and will be updated occasionally. Users are requested to submit additional data (e.g., more current, widely accepted, and/or documented data) and suggested changes to the address listed below. Please provide sources for all data provided.

Building energy, building leadership : recommendations for the adoption, development, and implementation of a commercial building energy code in Manitoba

Energy Technology Data Exchange (ETDEWEB)

Akerstream, T. [Manitoba Hydro, Winnipeg, MB (Canada); Allard, K. [City of Thompson, Thompson, MB (Canada); Anderson, N.; Beacham, D. [Manitoba Office of the Fire Commissioner, Winnipeg, MB (Canada); Andrich, R. [The Forks North Portage Partnership, MB (Canada); Auger, A. [Natural Resources Canada, Ottawa, ON (Canada). Office of Energy Efficiency; Downs, R.G. [Shindico Realty Inc., Winnipeg, MB (Canada); Eastwood, R. [Number Ten Architectural Group, Winnipeg, MB (Canada); Hewitt, C. [SMS Engineering Ltd., Winnipeg, MB (Canada); Joshi, D. [City of Winnipeg, Winnipeg, MB (Canada); Klassen, K. [Manitoba Dept. of Energy Science and Technology, Winnipeg, MB (Canada); Phillips, B. [Unies Ltd., Winnipeg, MB (Canada); Wiebe, R. [Ben Wiebe Construction Ltd., Winnipeg, MB (Canada); Woelk, D. [Bockstael Construction Ltd., Winnipeg, MB (Canada); Ziemski, S. [CREIT Management LLP, Winnipeg, MB (Canada)

2006-09-15

This report presented a strategy and a set of recommendations for the adoption, development and implementation of an energy code for new commercial construction in Manitoba. The report was compiled by an advisory committee comprised of industry representatives and government agency representatives. Recommendations were divided into 4 categories: (1) advisory committee recommendations; (2) code adoption recommendations; (3) code development recommendations; and (4) code implementation recommendations. It was suggested that Manitoba should adopt an amended version of the Model National Energy Code for Buildings (1997) as a regulation under the Buildings and Mobile Homes Act. Participation in a national initiative to update the Model National Energy Code for Buildings was also advised. It was suggested that the energy code should be considered as the first step in a longer-term process towards a sustainable commercial building code. However, the code should be adopted within the context of a complete market transformation approach. Other recommendations included: the establishment of a multi-stakeholder energy code task group; the provision of information and technical resources to help build industry capacity; the establishment of a process for energy code compliance; and an ongoing review of the energy code to assess impacts and progress. Supplemental recommendations for future discussion included the need for integrated design by building design teams in Manitoba; the development of a program to provide technical assistance to building design teams; and collaboration between post-secondary institutions to develop and deliver courses on integrated building design to students and professionals. 17 refs.

Safe Operation of Nuclear Power Plants. Code of Practice and Technical Appendices

International Nuclear Information System (INIS)

1969-01-01

This book is in two parts. The first is a Code of Practice for the Safe Operation of Nuclear Power Plants and the second part is a compilation of technical appendices. Its object is to give information and illustrative examples that would be helpful in implementing the Code of Practice. This second part, although published under the same cover, is not part of the Code. Safe operation of a nuclear power plant postulates suitable siting and proper design, construction and management of the plant. Under the present Code of Practice for the Safe Operation of Nuclear Power Plants, those intending to operate the plant are recommended to prepare documentation which would deal with its operation and include safety analyses. The documentation in question would be reviewed by a regulatory body independent of the operating organization; operation would be authorized on the understanding that it would comply with limits and conditions designed to ensure safety. The Code may be subject to revision in the light of experience. The Appendices provide additional information together with some examples relating to certain topics dealt with in the Code; it must be emphasized that they are included as examples for information only and are not part of any recommendation. Purpose and scope: The recommendations in the Code are designed to protect the general public and the operating personnel from radiation hazards, and the Code forms part of the Agency's Safety Standards. The Code, which should be used in conjunction with the Agency's other Safety Standards, provides guidance and information to persons and authorities responsible for the operation of stationary nuclear power plants whose main function is the generation of thermal, mechanical or electrical power; it is not intended to apply to reactors used solely for experimental or research purposes. It sets forth minimum requirements which, it is believed, in the light of experience, must be met in order to achieve safe operation of a

The Cost of Enforcing Building Energy Codes: Phase 1

Energy Technology Data Exchange (ETDEWEB)

Williams, Alison [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Vine, Ed [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Price, Sarah [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sturges, Andrew [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rosenquist, Greg [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2013-04-01

The purpose of this literature review is to summarize key findings regarding the costs associated with enforcing building energy code compliance—primarily focusing on costs borne by local government. The review takes into consideration over 150 documents that discuss, to some extent, code enforcement. This review emphasizes those documents that specifically focus on costs associated with energy code enforcement. Given the low rates of building energy code compliance that have been reported in existing studies, as well as the many barriers to both energy code compliance and enforcement, this study seeks to identify the costs of initiatives to improve compliance and enforcement. Costs are reported primarily as presented in the original source. Some costs are given on a per home or per building basis, and others are provided for jurisdictions of a certain size. This literature review gives an overview of state-based compliance rates, barriers to code enforcement, and U.S. Department of Energy (DOE) and key stakeholder involvement in improving compliance with building energy codes. In addition, the processes and costs associated with compliance and enforcement of building energy codes are presented. The second phase of this study, which will be presented in a different report, will consist of surveying 34 experts in the building industry at the national and state or local levels in order to obtain additional cost information, building on the findings from the first phase, as well as recommendations for where to most effectively spend money on compliance and enforcement.

Code of practice for the safe use of industrial radiography equipment (1989)

International Nuclear Information System (INIS)

1989-12-01

This code supersedes the Code of practice for the control and safe handling of sealed radioactive sources used in industrial radiography, published by the National Health and Medical Research Council (NHMRC) in 1968. It differs significantly from the former code because radiation protection practice and recommended standards have changed. The code covers the design, construction and requirements for the safe use of X-radiography equipment and gamma-radiography equipment. It provides illustrative working rules, detailed emergency procedures and comprehensive responsibilities and duties for all personnel involved in supplying and using industrial radiography equipment. The code details those equipment requirements, personnel requirements and work practices that the NHMRC considers necessary to keep exposures to ionizing radiation as low as reasonably achievable. Some equipment and facilities currently in use may not meet all of the mandatory requirements of this code. These requirements have been included in the code to encourage progress towards future compliance in the expectation that, in the interim, statutory authorities will apply them with discretion

Building codes: An often overlooked determinant of health.

Science.gov (United States)

Chauvin, James; Pauls, Jake; Strobl, Linda

2016-05-01

Although the vast majority of the world's population spends most of their time in buildings, building codes are not often thought of as 'determinants of health'. The standards that govern the design, construction, and use of buildings affect our health, security, safety, and well-being. This is true for dwellings, schools, and universities, shopping centers, places of recreation, places of worship, health-care facilities, and workplaces. We urge proactive engagement by the global public health community in developing these codes, and in the design and implementation of health protection and health promotion activities intended to reduce the risk of injury, disability, and death, particularly when due to poor building code adoption/adaption, application, and enforcement.

Implementation of Energy Code Controls Requirements in New Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, Michael I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hart, Philip R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hatten, Mike [Solarc Energy Group, LLC, Seattle, WA (United States); Jones, Dennis [Group 14 Engineering, Inc., Denver, CO (United States); Cooper, Matthew [Group 14 Engineering, Inc., Denver, CO (United States)

2017-03-24

Most state energy codes in the United States are based on one of two national model codes; ANSI/ASHRAE/IES 90.1 (Standard 90.1) or the International Code Council (ICC) International Energy Conservation Code (IECC). Since 2004, covering the last four cycles of Standard 90.1 updates, about 30% of all new requirements have been related to building controls. These requirements can be difficult to implement and verification is beyond the expertise of most building code officials, yet the assumption in studies that measure the savings from energy codes is that they are implemented and working correctly. The objective of the current research is to evaluate the degree to which high impact controls requirements included in commercial energy codes are properly designed, commissioned and implemented in new buildings. This study also evaluates the degree to which these control requirements are realizing their savings potential. This was done using a three-step process. The first step involved interviewing commissioning agents to get a better understanding of their activities as they relate to energy code required controls measures. The second involved field audits of a sample of commercial buildings to determine whether the code required control measures are being designed, commissioned and correctly implemented and functioning in new buildings. The third step includes compilation and analysis of the information gather during the first two steps. Information gathered during these activities could be valuable to code developers, energy planners, designers, building owners, and building officials.

1995 building energy codes and standards workshops: Summary and documentation

Energy Technology Data Exchange (ETDEWEB)

Sandahl, L.J.; Shankle, D.L.

1996-02-01

During the spring of 1995, Pacific Northwest National Laboratory (PNNL) conducted four two-day Regional Building Energy Codes and Standards workshops across the US. Workshops were held in Chicago, Denver, Rhode Island, and Atlanta. The workshops were designed to benefit state-level officials including staff of building code commissions, energy offices, public utility commissions, and others involved with adopting/updating, implementing, and enforcing building energy codes in their states. The workshops provided an opportunity for state and other officials to learn more about residential and commercial building energy codes and standards, the role of the US Department of Energy and the Building Standards and Guidelines Program at Pacific Northwest National Laboratory, Home Energy Rating Systems (HERS), Energy Efficient Mortgages (EEM), training issues, and other topics related to the development, adoption, implementation, and enforcement of building energy codes. Participants heard success stories, got tips on enforcement training, and received technical support materials. In addition to receiving information on the above topics, workshop participants had an opportunity to provide input on code adoption issues, building industry training issues, building design issues, and exemplary programs across the US. This paper documents the workshop planning, findings, and follow-up processes.

Code of practice for the safe use of industrial radiography equipment (1989)

International Nuclear Information System (INIS)

1989-12-01

This code supersedes the Code of Practice for the control and safe handling of sealed radioactive sources use din industrial radiography, published by the National Health and Medical Research Council (NHMRC) in 1968. It differs significantly from the former code because radiation protection practice and recommended standards have changed. The code covers the design, construction and requirements for the safe use of X-radiography equipment and gamma-radiography equipment. It provides illustrative working rules, detailed emergency procedures and comprehensive responsibilities and duties for all personnel involved in supplying and using industrial radiography equipment. The code details those equipment requirements, personnel requirements and work practices that the NHMRC considers necessary to keep exposures to ionizing radiation as low as reasonably achievable. Some equipment and facilities currently in use may not meet all of the mandatory requirements of this code. These requirements have been included in the code to encourage progress towards future compliance in the expectation that, in the interim, statutory authorities will apply them with discretion. 9 refs., tabs., ills

Building Codes and Regulations.

Science.gov (United States)

Fisher, John L.

The hazard of fire is of great concern to libraries due to combustible books and new plastics used in construction and interiors. Building codes and standards can offer architects and planners guidelines to follow but these standards should be closely monitored, updated, and researched for fire prevention. (DS)

An Examination of the Performance Based Building Code on the Design of a Commercial Building

Directory of Open Access Journals (Sweden)

John Greenwood

2012-11-01

Full Text Available The Building Code of Australia (BCA is the principal code under which building approvals in Australia are assessed. The BCA adopted performance-based solutions for building approvals in 1996. Performance-based codes are based upon a set of explicit objectives, stated in terms of a hierarchy of requirements beginning with key general objectives. With this in mind, the research presented in this paper aims to analyse the impact of the introduction of the performance-based code within Western Australia to gauge the effect and usefulness of alternative design solutions in commercial construction using a case study project. The research revealed that there are several advantages to the use of alternative designs and that all parties, in general, are in favour of the performance-based building code of Australia. It is suggested that change in the assessment process to streamline the alternative design path is needed for the greater use of the performance-based alternative. With appropriate quality control measures, minor variations to the deemed-to-satisfy provisions could easily be managed by the current and future building surveying profession.

Energy Efficiency Requirements in Building Codes, Energy Efficiency Policies for New Buildings. IEA Information Paper

Energy Technology Data Exchange (ETDEWEB)

Laustsen, Jens

2008-03-15

The aim of this paper is to describe and analyse current approaches to encourage energy efficiency in building codes for new buildings. Based on this analysis the paper enumerates policy recommendations for enhancing how energy efficiency is addressed in building codes and other policies for new buildings. This paper forms part of the IEA work for the G8 Gleneagles Plan of Action. These recommendations reflect the study of different policy options for increasing energy efficiency in new buildings and examination of other energy efficiency requirements in standards or building codes, such as energy efficiency requirements by major renovation or refurbishment. In many countries, energy efficiency of buildings falls under the jurisdiction of the federal states. Different standards cover different regions or climatic conditions and different types of buildings, such as residential or simple buildings, commercial buildings and more complicated high-rise buildings. There are many different building codes in the world and the intention of this paper is not to cover all codes on each level in all countries. Instead, the paper details different regions of the world and different ways of standards. In this paper we also evaluate good practices based on local traditions. This project does not seek to identify one best practice amongst the building codes and standards. Instead, different types of codes and different parts of the regulation have been illustrated together with examples on how they have been successfully addressed. To complement this discussion of efficiency standards, this study illustrates how energy efficiency can be improved through such initiatives as efficiency labelling or certification, very best practice buildings with extremely low- or no-energy consumption and other policies to raise buildings' energy efficiency beyond minimum requirements. When referring to the energy saving potentials for buildings, this study uses the analysis of recent IEA

The Influence of Building Codes on Recreation Facility Design.

Science.gov (United States)

Morrison, Thomas A.

1989-01-01

Implications of building codes upon design and construction of recreation facilities are investigated (national building codes, recreation facility standards, and misperceptions of design requirements). Recreation professionals can influence architectural designers to correct past deficiencies, but they must understand architectural and…

Lost opportunities: Modeling commercial building energy code adoption in the United States

International Nuclear Information System (INIS)

Nelson, Hal T.

2012-01-01

This paper models the adoption of commercial building energy codes in the US between 1977 and 2006. Energy code adoption typically results in an increase in aggregate social welfare by cost effectively reducing energy expenditures. Using a Cox proportional hazards model, I test if relative state funding, a new, objective, multivariate regression-derived measure of government capacity, as well as a vector of control variables commonly used in comparative state research, predict commercial building energy code adoption. The research shows little political influence over historical commercial building energy code adoption in the sample. Colder climates and higher electricity prices also do not predict more frequent code adoptions. I do find evidence of high government capacity states being 60 percent more likely than low capacity states to adopt commercial building energy codes in the following year. Wealthier states are also more likely to adopt commercial codes. Policy recommendations to increase building code adoption include increasing access to low cost capital for the private sector and providing noncompetitive block grants to the states from the federal government. - Highlights: ► Model the adoption of commercial building energy codes from 1977–2006 in the US. ► Little political influence over historical building energy code adoption. ► High capacity states are over 60 percent more likely than low capacity states to adopt codes. ► Wealthier states are more likely to adopt commercial codes. ► Access to capital and technical assistance is critical to increase code adoption.

24 CFR 200.926a - Residential building code comparison items.

Science.gov (United States)

2010-04-01

... 24 Housing and Urban Development 2 2010-04-01 2010-04-01 false Residential building code comparison items. 200.926a Section 200.926a Housing and Urban Development Regulations Relating to Housing and... § 200.926a Residential building code comparison items. HUD will review each local and State code...

SAFETY IN THE DESIGN OF SCIENCE LABORATORIES AND BUILDING CODES.

Science.gov (United States)

HOROWITZ, HAROLD

THE DESIGN OF COLLEGE AND UNIVERSITY BUILDINGS USED FOR SCIENTIFIC RESEARCH AND EDUCATION IS DISCUSSED IN TERMS OF LABORATORY SAFETY AND BUILDING CODES AND REGULATIONS. MAJOR TOPIC AREAS ARE--(1) SAFETY RELATED DESIGN FEATURES OF SCIENCE LABORATORIES, (2) LABORATORY SAFETY AND BUILDING CODES, AND (3) EVIDENCE OF UNSAFE DESIGN. EXAMPLES EMPHASIZE…

A long-term, integrated impact assessment of alternative building energy code scenarios in China

International Nuclear Information System (INIS)

Yu, Sha; Eom, Jiyong; Evans, Meredydd; Clarke, Leon

2014-01-01

China is the second largest building energy user in the world, ranking first and third in residential and commercial energy consumption. Beginning in the early 1980s, the Chinese government has developed a variety of building energy codes to improve building energy efficiency and reduce total energy demand. This paper studies the impact of building energy codes on energy use and CO 2 emissions by using a detailed building energy model that represents four distinct climate zones each with three building types, nested in a long-term integrated assessment framework GCAM. An advanced building stock module, coupled with the building energy model, is developed to reflect the characteristics of future building stock and its interaction with the development of building energy codes in China. This paper also evaluates the impacts of building codes on building energy demand in the presence of economy-wide carbon policy. We find that building energy codes would reduce Chinese building energy use by 13–22% depending on building code scenarios, with a similar effect preserved even under the carbon policy. The impact of building energy codes shows regional and sectoral variation due to regionally differentiated responses of heating and cooling services to shell efficiency improvement. - Highlights: • We assessed long-term impacts of building codes and climate policy using GCAM. • Building energy codes would reduce Chinese building energy use by 13–22%. • The impacts of codes on building energy use vary by climate region and sub-sector

use of the RESRAD-BUILD code to calculate building surface contamination limits

International Nuclear Information System (INIS)

Faillace, E.R.; LePoire, D.; Yu, C.

1996-01-01

Surface contamination limits in buildings were calculated for 226 Ra, 230 Th, 232 Th, and natural uranium on the basis of 1 mSv y -1 (100 mrem y -1 ) dose limit. The RESRAD-BUILD computer code was used to calculate these limits for two scenarios: building occupancy and building renovation. RESRAD-BUILD is a pathway analysis model designed to evaluate the potential radiological dose incurred by individuals working or living inside a building contaminated with radioactive material. Six exposure pathways are considered in the RESRAD-BUILD code: (1) external exposure directly from the source; (2) external exposure from materials deposited on the floor; (3) external exposure due to air submersion; (4) inhalation of airborne radioactive particles; (5) inhalation of aerosol indoor radon progeny; and (6) inadvertent ingestion of radioactive material, either directly from the sources or from materials deposited on the surfaces. The code models point, line, area, and volume sources and calculates the effects of radiation shielding, building ventilation, and ingrowth of radioactive decay products. A sensitivity analysis was performed to determine how variations in input parameters would affect the surface contamination limits. In most cases considered, inhalation of airborne radioactive particles was the primary exposure pathway. However, the direct external exposure contribution from surfaces contaminated with 226 Ra was in some cases the dominant pathway for building occupancy depending on the room size, ventilation rates, and surface release fractions. The surface contamination limits are most restrictive for 232 Th, followed by 230 Th, natural uranium, and 226 Ra. The results are compared with the surface contamination limits in the Nuclear Regulatory Commission's Regulatory Guide 1.86, which are most restrictive for 226 Ra and 230 Th, followed by 232 Th, and are least restrictive for natural uranium

Verification of RESRAD-build computer code, version 3.1

International Nuclear Information System (INIS)

2003-01-01

RESRAD-BUILD is a computer model for analyzing the radiological doses resulting from the remediation and occupancy of buildings contaminated with radioactive material. It is part of a family of codes that includes RESRAD, RESRAD-CHEM, RESRAD-RECYCLE, RESRAD-BASELINE, and RESRAD-ECORISK. The RESRAD-BUILD models were developed and codified by Argonne National Laboratory (ANL); version 1.5 of the code and the user's manual were publicly released in 1994. The original version of the code was written for the Microsoft DOS operating system. However, subsequent versions of the code were written for the Microsoft Windows operating system. The purpose of the present verification task (which includes validation as defined in the standard) is to provide an independent review of the latest version of RESRAD-BUILD under the guidance provided by ANSI/ANS-10.4 for verification and validation of existing computer programs. This approach consists of a posteriori V and V review which takes advantage of available program development products as well as user experience. The purpose, as specified in ANSI/ANS-10.4, is to determine whether the program produces valid responses when used to analyze problems within a specific domain of applications, and to document the level of verification. The culmination of these efforts is the production of this formal Verification Report. The first step in performing the verification of an existing program was the preparation of a Verification Review Plan. The review plan consisted of identifying: Reason(s) why a posteriori verification is to be performed; Scope and objectives for the level of verification selected; Development products to be used for the review; Availability and use of user experience; and Actions to be taken to supplement missing or unavailable development products. The purpose, scope and objectives for the level of verification selected are described in this section of the Verification Report. The development products that were used

The Cost of Enforcing Building Energy Codes: Phase 2

Energy Technology Data Exchange (ETDEWEB)

Williams, Alison [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Price, Sarah K. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Vine, Ed [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2014-10-15

The purpose of this study is to present key findings regarding costs associated with enforcing building energy code compliance–primarily focusing on costs borne by local government. Building codes, if complied with, have the ability to save a significant amount of energy. However, energy code compliance rates have been significantly lower than 100%. Renewed interest in building energy codes has focused efforts on increasing compliance, particularly as a result of the 2009 American Recovery and Reinvestment Act (ARRA) requirement that in order for states to receive additional energy grants, they must have “a plan for the jurisdiction achieving compliance with the building energy code…in at least 90 percent of new and renovated residential and commercial building space” by 2017 (Public Law 111-5, Section 410(2)(C)). One study by the Institute for Market Transformation (IMT) estimated the costs associated with reaching 90% compliance to be $810 million, or $610 million in additional funding over existing expenditures, a non-trivial value. [Majersik & Stellberg 2010] In this context, Lawrence Berkeley National Laboratory (LBNL) conducted a study to better pinpoint the costs of enforcement through a two-phase process.

Safe and Sustainable Tall Buildings - State of the Art

Directory of Open Access Journals (Sweden)

Mendis P.

2012-01-01

Full Text Available Tall buildings are becoming very popular around the world. Asia will have most of the tall buildings in this century. Both safety and sustainability aspects are important in planning and designing these buildings. The design and construction of tall buildings present many challenges for the design team, from engineers, architect through to the builder. Although structural systems could be developed and construction solutions could be found to design and construct very tall buildings in excess of 1 km (even 1 mile, other aspects such as fire and egress, long-term movements, environmental wind and perception of motion (including damping for dynamic effects, transportation (lifts issues, sustainability, durability and maintenance will govern and may even restrict the heights. Current practices and important issues related to design of safe and sustainable design of tall buildings are discussed in this paper.

Code of Practice for the safe transport of radioactive substances 1990

International Nuclear Information System (INIS)

1990-01-01

This Federal Code revises an earlier Code on the same subject issued in 1982 and was formulated under the Environment Protection (Nuclear Codes) Act 1978. The purpose of the Code is to establish uniform safety standards, applicable throughout the Commonwealth of Australia, to provide for the protection of persons and the environment, against any dangers associated with the transport of radioactive substances. The Code uses as a basis the IAEA Regulations for the Safe Transport of Radioactive Materials. This new edition takes into account the 1985 Edition of the Regulations incorporating the 1988 Supplement and provides, furthermore, that radiation protection standards will also be subject to recommendations of the Australian National Health and Medical Research Council [fr

Economic aspects and models for building codes

DEFF Research Database (Denmark)

Bonke, Jens; Pedersen, Dan Ove; Johnsen, Kjeld

It is the purpose of this bulletin to present an economic model for estimating the consequence of new or changed building codes. The object is to allow comparative analysis in order to improve the basis for decisions in this field. The model is applied in a case study.......It is the purpose of this bulletin to present an economic model for estimating the consequence of new or changed building codes. The object is to allow comparative analysis in order to improve the basis for decisions in this field. The model is applied in a case study....

SAFE: A computer code for the steady-state and transient thermal analysis of LMR fuel elements

International Nuclear Information System (INIS)

Hayes, S.L.

1993-12-01

SAFE is a computer code developed for both the steady-state and transient thermal analysis of single LMR fuel elements. The code employs a two-dimensional control-volume based finite difference methodology with fully implicit time marching to calculate the temperatures throughout a fuel element and its associated coolant channel for both the steady-state and transient events. The code makes no structural calculations or predictions whatsoever. It does, however, accept as input structural parameters within the fuel such as the distributions of porosity and fuel composition, as well as heat generation, to allow a thermal analysis to be performed on a user-specified fuel structure. The code was developed with ease of use in mind. An interactive input file generator and material property correlations internal to the code are available to expedite analyses using SAFE. This report serves as a complete design description of the code as well as a user's manual. A sample calculation made with SAFE is included to highlight some of the code's features. Complete input and output files for the sample problem are provided

International building code for bamboo

NARCIS (Netherlands)

Janssen, J.J.A.; Kumar, Arun; Ramanuja Rao, I.V.; Sastry, Cherla

2002-01-01

One of the recommendations in the International Bamboo Congress and Workshop, held at Bali in 1995, requested the International Network for Bamboo and Rattan (INBAR), "to organize a task force to discuss and finalize a building code for bamboo". Consequently a draft was prepared under the title, "An

Policy Pathways: Modernising Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-01

Buildings are the largest consumers of energy worldwide and will continue to be a source of increasing energy demand in the future. Globally, the sector’s final energy consumption doubled between 1971 and 2010 to reach 2 794 million tonnes of oil equivalent (Mtoe), driven primarily by population increase and economic growth. Under current policies, the global energy demand of buildings is projected by the IEA experts to grow by an additional 838 Mtoe by 2035 compared to 2010. The challenges of the projected increase of energy consumption due to the built environment vary by country. In IEA member countries, much of the future buildings stock is already in place, and so the main challenge is to renovate existing buildings stock. In non-IEA countries, more than half of the buildings stock needed by 2050 has yet to be built. The IEA and the UNDP partnered to analyse current practices in the design and implementation of building energy codes. The aim is to consolidate existing efforts and to encourage more attention to the role of the built environment in a low-carbon and climate-resilient world. This joint IEA-UNDP Policy Pathway aims to share lessons learned between IEA member countries and non-IEA countries. The objective is to spread best practices, limit pressures on global energy supply, improve energy security, and contribute to environmental sustainability. Part of the IEA Policy Pathway series, Modernising building energy codes to secure our global energy future sets out key steps in planning, implementation, monitoring and evaluation. The Policy Pathway series aims to help policy makers implement the IEA 25 Energy Efficiency Policy Recommendations endorsed by IEA Ministers (2011).

A MODEL BUILDING CODE ARTICLE ON FALLOUT SHELTERS WITH RECOMMENDATIONS FOR INCLUSION OF REQUIREMENTS FOR FALLOUT SHELTER CONSTRUCTION IN FOUR NATIONAL MODEL BUILDING CODES.

Science.gov (United States)

American Inst. of Architects, Washington, DC.

A MODEL BUILDING CODE FOR FALLOUT SHELTERS WAS DRAWN UP FOR INCLUSION IN FOUR NATIONAL MODEL BUILDING CODES. DISCUSSION IS GIVEN OF FALLOUT SHELTERS WITH RESPECT TO--(1) NUCLEAR RADIATION, (2) NATIONAL POLICIES, AND (3) COMMUNITY PLANNING. FALLOUT SHELTER REQUIREMENTS FOR SHIELDING, SPACE, VENTILATION, CONSTRUCTION, AND SERVICES SUCH AS ELECTRICAL…

7 CFR Exhibit E to Subpart A of... - Voluntary National Model Building Codes

Science.gov (United States)

2010-01-01

... 7 Agriculture 12 2010-01-01 2010-01-01 false Voluntary National Model Building Codes E Exhibit E... National Model Building Codes The following documents address the health and safety aspects of buildings and related structures and are voluntary national model building codes as defined in § 1924.4(h)(2) of...

The Role of the International Code Council in the U.S. Building Regukation System and Green Building Contruction

OpenAIRE

David Walls

2015-01-01

This paper will address the components of the International Code Council (ICC) as one of the most important organizations in terms of developing the model building codes for the US: the international codes. This membership-driven organization has the task of providing the building industry and all its stakeholders with the necessary regulatory documents, training, certification, plan check, product evaluation, and accreditation services to achieve safer and more sustainable building construct...

78 FR 55245 - Activities and Methodology for Assessing Compliance With Building Energy Codes

Science.gov (United States)

2013-09-10

...-0036] Activities and Methodology for Assessing Compliance With Building Energy Codes AGENCY: Office of... available to states to evaluate compliance with building energy codes and general approaches towards... building energy codes and general approaches towards compliance. The comment period ended on September 5...

Radon Protection in the Technical Building Code

International Nuclear Information System (INIS)

Frutos, B.; Garcia, J. P.; Martin, J. L.; Olaya, M.; Serrano, J I.; Suarez, E.; Fernandez, J. A.; Rodrigo, F.

2003-01-01

Building construction in areas with high radon gas contamination in land requires the incorporation of certain measures in order to prevent the accumulation of this gas on the inside of buildings. These measures should be considered primarily in the design and construction phases and should take the area of the country into consideration where the construction will take place depending on the potential risk of radon entrance. Within the Technical Building Code, radon protection has been considered through general classification of the country and specific areas where building construction is to take place, in different risk categories and in the introduction of building techniques appropriate for each area. (Author) 17 refs

Code Compliant School Buildings Boost Student Achievement

Directory of Open Access Journals (Sweden)

Ronald B. Lumpkin

2014-11-01

Full Text Available Much of the focus in the literature in raising student achievement has included parental involvement, principal leadership, quality of instruction, students’ socioeconomic status, curriculum, and use of technology. Limited empirical research relates the condition of the school building as a variable that affects student achievement. Furthermore, there is no research that has examined the impact of building codes on achievement outcomes in the state of Florida. This research determined whether academic achievement of 4th-, 8th-, 9th-, and 10th-grade students as measured by the mathematics and reading subtests of the Florida Comprehensive Achievement Test (FCAT increased in new school buildings compliant to the 2000 Florida State Requirements for Educational Facilities. A causal-comparative design determined whether the independent variables, old and new school building influenced student achievement as measured by students’ FCAT mathematics and reading subtest scores. The control group was two cohorts of 4th-, 8th-, 9th-, and 10th-grade students who attended school in old buildings. The experimental group was two cohorts of 4th-, 8th-, 9th-, and 10th-grade students who attended school in new buildings. Transition from an old school into a new school was the treatment. Two hypotheses were formulated for testing and the research question for the inquiry was whether the percentage of students passing the FCAT mathematics and reading subtests increases after transitioning from an old school building into a new 2000 UBC (Uniform Building Code compliant facility.

76 FR 57982 - Building Energy Codes Cost Analysis

Science.gov (United States)

2011-09-19

... DEPARTMENT OF ENERGY Office of Energy Efficiency and Renewable Energy [Docket No. EERE-2011-BT-BC-0046] Building Energy Codes Cost Analysis Correction In notice document 2011-23236 beginning on page...-23236 Filed 9-16-11; 8:45 am] BILLING CODE 1505-01-P ...

Code of safe practice for the use of x-rays in dentistry

International Nuclear Information System (INIS)

1991-06-01

The purpose of this Code of Safe Practice for the Use of X-rays in Dentistry is to provide criteria for working procedures, x-ray equipment and protective materials necessary for the use of x-rays in dental diagnosis according to currently accepted standards of safety. Conformity with this code may be taken as a primary indication of compliance with radiation protection legislation. 7 refs., 1 ill

Performance-based building codes: a call for injury prevention indicators that bridge health and building sectors.

Science.gov (United States)

Edwards, N

2008-10-01

The international introduction of performance-based building codes calls for a re-examination of indicators used to monitor their implementation. Indicators used in the building sector have a business orientation, target the life cycle of buildings, and guide asset management. In contrast, indicators used in the health sector focus on injury prevention, have a behavioural orientation, lack specificity with respect to features of the built environment, and do not take into account patterns of building use or building longevity. Suggestions for metrics that bridge the building and health sectors are discussed. The need for integrated surveillance systems in health and building sectors is outlined. It is time to reconsider commonly used epidemiological indicators in the field of injury prevention and determine their utility to address the accountability requirements of performance-based codes.

Pinoleville Pomo Nation Tribal Green Building Code

Science.gov (United States)

The Pinoleville Pomo Nation (PPN) worked with the U.S. Environmental Protection Agency (EPA) and the Development Center for Appropriate Technology (DCAT) to create this framework for tribal building codes.

Pushover, Response Spectrum and Time History Analyses of Safe Rooms in a Poor Performance Masonry Building

International Nuclear Information System (INIS)

Mazloom, M.

2008-01-01

The idea of safe room has been developed for decreasing the earthquake casualties in masonry buildings. The information obtained from the previous ground motions occurring in seismic zones expresses the lack of enough safety of these buildings against earthquakes. For this reason, an attempt has been made to create some safe areas inside the existing masonry buildings, which are called safe rooms. The practical method for making these safe areas is to install some prefabricated steel frames in some parts of the existing structure. These frames do not carry any service loads before an earthquake. However, if a devastating earthquake happens and the load bearing walls of the building are destroyed, some parts of the floors, which are in the safe areas, will fall on the roof of the installed frames and the occupants who have sheltered there will survive. This paper presents the performance of these frames located in a destroying three storey masonry building with favorable conclusions. In fact, the experimental pushover diagram of the safe room located at the ground-floor level of this building is compared with the analytical results and it is concluded that pushover analysis is a good method for seismic performance evaluation of safe rooms. For time history analysis the 1940 El Centro, the 2003 Bam, and the 1990 Manjil earthquake records with the maximum peak accelerations of 0.35g were utilized. Also the design spectrum of Iranian Standard No. 2800-05 for the ground kind 2 is used for response spectrum analysis. The results of time history, response spectrum and pushover analyses show that the strength and displacement capacity of the steel frames are adequate to accommodate the distortions generated by seismic loads and aftershocks properly

A Perspective of Energy Codes and Regulations for the Buildings of the Future

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, Michael [Pacific Northwest National Laboratory,2032 Todd Street,Eugene, OR 97405e-mail: michael.rosenberg@pnnl.gov; Jonlin, Duane [Seattle Department ofConstruction and Inspections,P.O. Box 34019,Seattle, WA 98124e-mail: duane.jonlin@seattle.gov; Nadel, Steven [American Council for anEnergy-Efficient Economy,529 14th Street NW #600,Washington, DC 20045e-mail: snadel@aceee.org

2016-10-13

Today’s building energy codes focus on prescriptive requirements for features of buildings that are directly controlled by the design and construction teams and verifiable by municipal inspectors. Although these code requirements have had a significant impact, they fail to influence a large slice of the building energy use pie – including not only miscellaneous plug loads, cooking equipment and commercial/industrial processes, but the maintenance and optimization of the code-mandated systems as well. Currently, code compliance is verified only through the end of construction, and there are no limits or consequences for the actual energy use in an occupied building. In the future, our suite of energy regulations will likely expand to include building efficiency, energy use or carbon emission budgets over their full life cycle. Intelligent building systems, extensive renewable energy, and a transition from fossil fuel to electric heating systems will likely be required to meet ultra-low-energy targets. This paper lays out the authors’ perspectives on how buildings may evolve over the course of the 21st century and the roles that codes and regulations will play in shaping those buildings of the future.

Model Code of Safe Practice in the Petroleum Industry: Pt. 8

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

This code has been prepared for use on a worldwide basis as a guide to safe practice for those concerned with drilling and production operations for oil and gas in offshore areas. It is intended to provide information and guidance on those offshore drilling, production and support activities which have an impact on safety and therefore require detailed care and attention. Each chapter of the Code covers an important drilling, production or support activity and has an introduction which describes the part each activity plays in the overall offshore operation. (author).

Integrating Renewable Energy Requirements Into Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Kaufmann, John R.; Hand, James R.; Halverson, Mark A.

2011-07-01

This report evaluates how and when to best integrate renewable energy requirements into building energy codes. The basic goals were to: (1) provide a rough guide of where we’re going and how to get there; (2) identify key issues that need to be considered, including a discussion of various options with pros and cons, to help inform code deliberations; and (3) to help foster alignment among energy code-development organizations. The authors researched current approaches nationally and internationally, conducted a survey of key stakeholders to solicit input on various approaches, and evaluated the key issues related to integration of renewable energy requirements and various options to address those issues. The report concludes with recommendations and a plan to engage stakeholders. This report does not evaluate whether the use of renewable energy should be required on buildings; that question involves a political decision that is beyond the scope of this report.

Cost and code study of underground building: a report to the Minnesota Energy Agency

Energy Technology Data Exchange (ETDEWEB)

Sterling, R L

1979-11-01

The rapidly intensifying interest in the possible energy savings and environmental and land-use benefits associated with underground buildings has led increasing numbers of people to question restrictions that existing building codes place on underground construction and to make cost comparisons between underground structures and more-conventional buildings. Information in this report on earth-sheltered houses covers public policy issues (building code restrictions, taxation, insurance) and residential construction costs (cost breakdowns, general factors affecting costs, and life-cycle costs). The report also deals with regulatory and insurance issues (building codes, fire protection, insurance provisions) and construction costs for large underground buildings. The report recommends that: (1) the Minnesota Energy Agency consult with the Building Code Division of the Department of Administration on HUD Minimum Property Standards to examine the possibility of modifying several building-code requirements that affect earth-sheltered housing design; (2) HUD Minimum Property Standards be brought into line with the major building codes on the question of optional mechanical ventilation in houses; (3) model ordinances concerning setbacks, basement house provisions, and minimum square footage provisions to be drafted; (4) legal questions concerning the separation of ownership of the surface from that subsurface space be resolved; (5) questions concerning taxation of mined space be resolved; and (6) a life-cost inventory of underground residences and buildings in Minnesota be compiled.

New "Risk-Targeted" Seismic Maps Introduced into Building Codes

Science.gov (United States)

Luco, Nicholas; Garrett, B.; Hayes, J.

2012-01-01

Throughout most municipalities of the United States, structural engineers design new buildings using the U.S.-focused International Building Code (IBC). Updated editions of the IBC are published every 3 years. The latest edition (2012) contains new "risk-targeted maximum considered earthquake" (MCER) ground motion maps, which are enabling engineers to incorporate a more consistent and better defined level of seismic safety into their building designs.

Energy Efficiency Program Administrators and Building Energy Codes

Science.gov (United States)

Explore how energy efficiency program administrators have helped advance building energy codes at federal, state, and local levels—using technical, institutional, financial, and other resources—and discusses potential next steps.

Renewable Energy and Energy Efficiency Technologies in Residential Building Codes: June 15, 1998 to September 15, 1998

Energy Technology Data Exchange (ETDEWEB)

Wortman, D.; Echo-Hawk, L.

2005-02-01

This report is an attempt to describe the building code requirements and impediments to the application of EE and RE technologies in residential buildings. Several modern model building codes were reviewed. These are representative of the codes that will be adopted by most locations in the coming years. The codes reviewed for this report include: International Residential Code, First Draft, April 1998; International Energy Conservation Code, 1998; International Mechanical Code, 1998; International Plumbing Code, 1997; International Fuel Gas Code, 1997; National Electrical Code, 1996. These codes were reviewed as to their application to (1) PV systems in buildings and building-integrated PV systems and (2) active solar domestic hot water and space-heating systems. A discussion of general code issues that impact these technologies is also included. Examples of this are solar access and sustainability.

Safe operation of research reactors and critical assemblies. Code of practice and annexes. 1984 ed

International Nuclear Information System (INIS)

1984-01-01

The safe operation of research reactors and critical assemblies (hereafter termed 'reactors') requires proper design, construction, management and supervision. This Code of Practice deals mainly with management and supervision. The provisions of the Code apply to the whole life of the reactor, including modification, updating and upgrading. The Code may be subject to revision in the light of experience and the state of technology. The Code is aimed at defining minimum requirements for the safe operation of reactors. Emphasis is placed on which safety requirements should be met rather than on specifying how these requirements may be met. The Code also provides guidance and information to persons and authorities responsible for the operation of reactors. The Code recommends that documents dealing with the operation of reactors and including safety analyses be prepared and submitted for review and approval to a regulatory body. Operation would be authorized on the understanding that it would comply with limits and conditions designed to ensure safety. The Code covers a wide range of reactor types, which gives rise to a variety of safety issues. Safety issues applicable to specific reactor types only (e.g. fast reactors) are not necessarily covered in this Code. Some of the recommendations in the Code are not directly applicable to critical assemblies. A recommendation may therefore be interpreted according to the type of reactor concerned. In such cases the words 'adequate' and 'appropriate' are used to mean 'adequate' or 'appropriate' for the type of reactor under consideration.

76 FR 27843 - National Building Safety Month, 2011

Science.gov (United States)

2011-05-13

... organizations and the public and private sectors--to implement effective standards and codes that sustain safe... and fire prevention codes help us withstand, mitigate, and rapidly recover from hurricanes, winter... Building Safety Month. I encourage citizens, government agencies, private businesses, nonprofit...

Potential Job Creation in Nevada as a Result of Adopting New Residential Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Scott, Michael J.; Niemeyer, Jackie M.

2013-09-01

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levels of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.

Potential Job Creation in Tennessee as a Result of Adopting New Residential Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Scott, Michael J.; Niemeyer, Jackie M.

2013-09-01

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levels of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.

Potential Job Creation in Minnesota as a Result of Adopting New Residential Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Scott, Michael J.; Niemeyer, Jackie M.

2013-09-01

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levels of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.

Building climate change into infrastructure codes and standards

International Nuclear Information System (INIS)

Auld, H.; Klaasen, J.; Morris, R.; Fernandez, S.; MacIver, D.; Bernstein, D.

2009-01-01

'Full text:' Building codes and standards and the climatic design values embedded within these legal to semi-legal documents have profound safety, health and economic implications for Canada's infrastructure systems. The climatic design values that have been used for the design of almost all of today's more than $5.5 Trillion in infrastructure are based on historical climate data and assume that the extremes of the past will represent future conditions. Since new infrastructure based on codes and standards will be built to survive for decades to come, it is critically important that existing climatic design information be as accurate and up-to-date as possible, that the changing climate be monitored to detect and highlight vulnerabilities of existing infrastructure, that forensic studies of climate-related failures be undertaken and that codes and standards processes incorporate future climates and extremes as much as possible. Uncertainties in the current climate change models and their scenarios currently challenge our ability to project future extremes regionally and locally. Improvements to the spatial and temporal resolution of these climate change scenarios, along with improved methodologies to treat model biases and localize results, will allow future codes and standards to better reflect the extremes and weathering conditions expected over the lifespan of structures. In the meantime, other information and code processes can be used to incorporate changing climate conditions into upcoming infrastructure codes and standards, to “bridge” the model uncertainty gap and to complement the state of existing projections. This presentation will outline some of the varied information and processes that will be used to incorporate climate change adaptation into the next development cycle of the National Building Code of Canada and numerous other national CSA infrastructure standards. (author)

Building America Guidance for Identifying and Overcoming Code, Standard, and Rating Method Barriers

Energy Technology Data Exchange (ETDEWEB)

Cole, Pamala C.; Halverson, Mark A.

2013-09-01

The U.S. Department of Energy’s (DOE) Building America program implemented a new Codes and Standards Innovation (CSI) Team in 2013. The Team’s mission is to assist Building America (BA) research teams and partners in identifying and resolving conflicts between Building America innovations and the various codes and standards that govern the construction of residences. A CSI Roadmap was completed in September, 2013. This guidance document was prepared using the information in the CSI Roadmap to provide BA research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America (BA) innovations arising in and/or stemming from codes, standards, and rating methods. For more information on the BA CSI team, please email: CSITeam@pnnl.gov

Code of practice for the safe use of ionizing radiation in secondary schools (1986)

International Nuclear Information System (INIS)

1987-01-01

The code of practice is intended for schools and indicates the basic philosophy behind the current approach to the control of hazards associated with the use of ionizing radiation. The purpose of this code is to provide guidance on safe and proper practices in the use of radiation. It covers modes of radiation exposure, shielding, dose limits, responsibility, general rules, x-ray generators, general control of radioactive sources, sealed sources and unsealed sources

Evaluating the benefits of commercial building energy codes and improving federal incentives for code adoption.

Science.gov (United States)

Gilbraith, Nathaniel; Azevedo, Inês L; Jaramillo, Paulina

2014-12-16

The federal government has the goal of decreasing commercial building energy consumption and pollutant emissions by incentivizing the adoption of commercial building energy codes. Quantitative estimates of code benefits at the state level that can inform the size and allocation of these incentives are not available. We estimate the state-level climate, environmental, and health benefits (i.e., social benefits) and reductions in energy bills (private benefits) of a more stringent code (ASHRAE 90.1-2010) relative to a baseline code (ASHRAE 90.1-2007). We find that reductions in site energy use intensity range from 93 MJ/m(2) of new construction per year (California) to 270 MJ/m(2) of new construction per year (North Dakota). Total annual benefits from more stringent codes total $506 million for all states, where $372 million are from reductions in energy bills, and $134 million are from social benefits. These total benefits range from $0.6 million in Wyoming to $49 million in Texas. Private benefits range from $0.38 per square meter in Washington State to $1.06 per square meter in New Hampshire. Social benefits range from $0.2 per square meter annually in California to $2.5 per square meter in Ohio. Reductions in human/environmental damages and future climate damages account for nearly equal shares of social benefits.

Potential Job Creation in Rhode Island as a Result of Adopting New Residential Building Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Scott, Michael J.; Niemeyer, Jackie M.

2013-09-01

Are there advantages to states that adopt the most recent model building energy codes other than saving energy? For example, can the construction activity and energy savings associated with code-compliant housing units become significant sources of job creation for states if new building energy codes are adopted to cover residential construction? , The U.S. Department of Energy (DOE) Building Energy Codes Program (BECP) asked Pacific Northwest National Laboratory (PNNL) to research and ascertain whether jobs would be created in individual states based on their adoption of model building energy codes. Each state in the country is dealing with high levels of unemployment, so job creation has become a top priority. Many programs have been created to combat unemployment with various degrees of failure and success. At the same time, many states still have not yet adopted the most current versions of the International Energy Conservation Code (IECC) model building energy code, when doing so could be a very effective tool in creating jobs to assist states in recovering from this economic downturn.

Compatibility of global environmental assessment methods of buildings with an Egyptian energy code

Directory of Open Access Journals (Sweden)

Amal Kamal Mohamed Shamseldin

2017-04-01

Full Text Available Several environmental assessment methods of buildings had emerged over the world to set environmental classifications for buildings, such as the American method “Leadership in Energy and Environmental Design” (LEED the most widespread one. Several countries decided to put their own assessment methods to catch up with the previous orientation, such as Egypt. The main goal of putting the Egyptian method was to impose the voluntary local energy efficiency codes. Through a local survey, it was clearly noted that many of the construction makers in Egypt do not even know the local method, and whom are interested in the environmental assessment of buildings seek to apply LEED rather than anything else. Therefore, several questions appear about the American method compatibility with the Egyptian energy codes – that contain the most exact characteristics and requirements and give the outmost credible energy efficiency results for buildings in Egypt-, and the possibility of finding another global method that gives closer results to those of the Egyptian codes, especially with the great variety of energy efficiency measurement approaches used among the different assessment methods. So, the researcher is trying to find the compatibility of using non-local assessment methods with the local energy efficiency codes. Thus, if the results are not compatible, the Egyptian government should take several steps to increase the local building sector awareness of the Egyptian method to benefit these codes, and it should begin to enforce it within the building permits after a proper guidance and feedback.

Comparison of energy conservation building codes of Iran, Turkey, Germany, China, ISO 9164 and EN 832

International Nuclear Information System (INIS)

Fayaz, Rima; Kari, Behrouz M.

2009-01-01

To improve the energy efficiency of buildings via compliance to regulation in Iran, Code No. 19 was devised in 1991. The code lacks high level aims and objectives, addressing the characteristics of Iranian buildings. As a consequence, the code has been revised and is not completely implemented in practice, and still remains inefficient. As with any energy coding system, this code has to identify the right balance between the different energy variables for the Iranian climate and way of life. In order to assist improvements to high level objectives of Code 19, this code is compared with ISO 9164, EN 832, German regulation, TS 825 of Turkey and China's GB 50189 to understand how these have adapted international standards to national features. In order to test the appropriateness of Code 19, five case study buildings in Iran are assessed against Code 19 as well as Turkish standard TS 825 and the results are compared. The results demonstrate that Code 19 is efficient in calculations of building envelope, but it needs improvements in the areas of ventilation, gains from internal and solar sources. The paper concludes by offering suggestions for improving the code.

Reliable JavaScript how to code safely in the world's most dangerous language

CERN Document Server

Spencer, Lawrence

2015-01-01

Create more robust applications with a test-first approach to JavaScript Reliable JavaScript, How to Code Safely in the World's Most Dangerous Language demonstrates how to create test-driven development for large-scale JavaScript applications that will stand the test of time and stay accurate through long-term use and maintenance. Taking a test-first approach to software architecture, this book walks you through several patterns and practices and explains what they are supposed to do by having you write unit tests. Write the code to pass the unit tests, so you not only develop your technique

Building code challenging the ethics behind adobe architecture in North Cyprus.

Science.gov (United States)

Hurol, Yonca; Yüceer, Hülya; Şahali, Öznem

2015-04-01

Adobe masonry is part of the vernacular architecture of Cyprus. Thus, it is possible to use this technology in a meaningful way on the island. On the other hand, although adobe architecture is more sustainable in comparison to other building technologies, the use of it is diminishing in North Cyprus. The application of Turkish building code in the north of the island has created complications in respect of the use of adobe masonry, because this building code demands that reinforced concrete vertical tie-beams are used together with adobe masonry. The use of reinforced concrete elements together with adobe masonry causes problems in relation to the climatic response of the building as well as causing other technical and aesthetic problems. This situation makes the design of adobe masonry complicated and various types of ethical problems also emerge. The objective of this article is to analyse the ethical problems which arise as a consequence of the restrictive character of the building code, by analysing two case studies and conducting an interview with an architect who was involved with the use of adobe masonry in North Cyprus. According to the results of this article there are ethical problems at various levels in the design of both case studies. These problems are connected to the responsibilities of architects in respect of the social benefit, material production, aesthetics and affordability of the architecture as well as presenting distrustful behaviour where the obligations of architects to their clients is concerned.

ICAN Computer Code Adapted for Building Materials

Science.gov (United States)

Murthy, Pappu L. N.

1997-01-01

The NASA Lewis Research Center has been involved in developing composite micromechanics and macromechanics theories over the last three decades. These activities have resulted in several composite mechanics theories and structural analysis codes whose applications range from material behavior design and analysis to structural component response. One of these computer codes, the Integrated Composite Analyzer (ICAN), is designed primarily to address issues related to designing polymer matrix composites and predicting their properties - including hygral, thermal, and mechanical load effects. Recently, under a cost-sharing cooperative agreement with a Fortune 500 corporation, Master Builders Inc., ICAN was adapted to analyze building materials. The high costs and technical difficulties involved with the fabrication of continuous-fiber-reinforced composites sometimes limit their use. Particulate-reinforced composites can be thought of as a viable alternative. They are as easily processed to near-net shape as monolithic materials, yet have the improved stiffness, strength, and fracture toughness that is characteristic of continuous-fiber-reinforced composites. For example, particlereinforced metal-matrix composites show great potential for a variety of automotive applications, such as disk brake rotors, connecting rods, cylinder liners, and other hightemperature applications. Building materials, such as concrete, can be thought of as one of the oldest materials in this category of multiphase, particle-reinforced materials. The adaptation of ICAN to analyze particle-reinforced composite materials involved the development of new micromechanics-based theories. A derivative of the ICAN code, ICAN/PART, was developed and delivered to Master Builders Inc. as a part of the cooperative activity.

Using Third-Party Inspectors in Building Energy Codes Enforcement in India

Energy Technology Data Exchange (ETDEWEB)

Yu, Sha; Evans, Meredydd; Kumar, Pradeep; Van Wie, Laura; Bhatt, Vatsal

2013-01-31

India is experiencing fast income growth and urbanization, and this leads to unprecedented increases in demand for building energy services and resulting energy consumption. In response to rapid growth in building energy use, the Government of India issued the Energy Conservation Building Code (ECBC) in 2007, which is consistent with and based on the 2001 Energy Conservation Act. ECBC implementation has been voluntary since its enactment and a few states have started to make progress towards mandatory implementation. Rajasthan is the first state in India to adopt ECBC as a mandatory code. The State adopted ECBC with minor additions on March 28, 2011 through a stakeholder process; it became mandatory in Rajasthan on September 28, 2011. Tamil Nadu, Gujarat, and Andhra Pradesh have started to draft an implementation roadmap and build capacity for its implementation. The Bureau of Energy Efficiency (BEE) plans to encourage more states to adopt ECBC in the near future, including Haryana, Uttar Pradesh, Karnataka, Maharashtra, West Bengal, and Delhi. Since its inception, India has applied the code on a voluntary basis, but the Government of India is developing a strategy to mandate compliance. Implementing ECBC requires coordination between the Ministry of Power and the Ministry of Urban Development at the national level as well as interdepartmental coordination at the state level. One challenge is that the Urban Local Bodies (ULBs), the enforcement entities of building by-laws, lack capacity to implement ECBC effectively. For example, ULBs in some states might find the building permitting procedures to be too complex; in other cases, lack of awareness and technical knowledge on ECBC slows down the amendment of local building by-laws as well as ECBC implementation. The intent of this white paper is to share with Indian decision-makers code enforcement approaches: through code officials, third-party inspectors, or a hybrid approach. Given the limited capacity and human

Innovation and Standardization in School Building: A Proposal for the National Code in Italy.

Science.gov (United States)

Ridolfi, Giuseppe

This document discusses the University of Florence's experience and concepts as it developed the research to define a proposal for designing a new national school building code. Section 1 examines the current school building code and the Italian Reform Process in Education between 1960 and 2000. Section 2 details and explains the new school…

76 FR 13101 - Building Energy Codes Program: Presenting and Receiving Comments to DOE Proposed Changes to the...

Science.gov (United States)

2011-03-10

... DEPARTMENT OF ENERGY 10 CFR Part 430 [Docket No. EERE-2011-BT-BC-0009] Building Energy Codes.... The IgCC is intended to provide a green model building code provisions for new and existing commercial... Code (IgCC) AGENCY: Office of Energy Efficiency and Renewable Energy, Department of Energy. ACTION...

Assessing Potential Energy Cost Savings from Increased Energy Code Compliance in Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, Michael I.; Hart, Philip R.; Athalye, Rahul A.; Zhang, Jian; Wang, Weimin

2016-02-15

The US Department of Energy’s most recent commercial energy code compliance evaluation efforts focused on determining a percent compliance rating for states to help them meet requirements under the American Recovery and Reinvestment Act (ARRA) of 2009. That approach included a checklist of code requirements, each of which was graded pass or fail. Percent compliance for any given building was simply the percent of individual requirements that passed. With its binary approach to compliance determination, the previous methodology failed to answer some important questions. In particular, how much energy cost could be saved by better compliance with the commercial energy code and what are the relative priorities of code requirements from an energy cost savings perspective? This paper explores an analytical approach and pilot study using a single building type and climate zone to answer those questions.

Empirical evidence for site coefficients in building code provisions

Science.gov (United States)

Borcherdt, R.D.

2002-01-01

Site-response coefficients, Fa and Fv, used in U.S. building code provisions are based on empirical data for motions up to 0.1 g. For larger motions they are based on theoretical and laboratory results. The Northridge earthquake of 17 January 1994 provided a significant new set of empirical data up to 0.5 g. These data together with recent site characterizations based on shear-wave velocity measurements provide empirical estimates of the site coefficients at base accelerations up to 0.5 g for Site Classes C and D. These empirical estimates of Fa and Fnu; as well as their decrease with increasing base acceleration level are consistent at the 95 percent confidence level with those in present building code provisions, with the exception of estimates for Fa at levels of 0.1 and 0.2 g, which are less than the lower confidence bound by amounts up to 13 percent. The site-coefficient estimates are consistent at the 95 percent confidence level with those of several other investigators for base accelerations greater than 0.3 g. These consistencies and present code procedures indicate that changes in the site coefficients are not warranted. Empirical results for base accelerations greater than 0.2 g confirm the need for both a short- and a mid- or long-period site coefficient to characterize site response for purposes of estimating site-specific design spectra.

41 CFR 102-80.85 - Are Federally owned and leased buildings exempt from State and local code requirements in fire...

Science.gov (United States)

2010-07-01

... leased buildings exempt from State and local code requirements in fire protection? 102-80.85 Section 102... Fire Prevention State and Local Codes § 102-80.85 Are Federally owned and leased buildings exempt from State and local code requirements in fire protection? Federally owned buildings are generally exempt...

Are green building features safe for preventive maintenance workers? Examining the evidence.

Science.gov (United States)

Omar, Mohamed Shamun; Quinn, Margaret M; Buchholz, Bryan; Geiser, Ken

2013-04-01

Many newly constructed green buildings (GB) are certified using the United States Green Building Council (USGBC) Leadership in Energy and Environmental Design (LEED) rating system for new construction and major renovation which focuses on architectural and mechanical design to conserve energy, reduce environmental harm, and enhance indoor quality for occupants. This study evaluated the preventive maintenance (PM) worker occupational safety and health (OSH) risks related to the design of GB. PM job hazard analyses (JHA) were performed on the tasks required to operate and maintain five GB features selected from 13 LEED certified GB. A 22-item JHA and OSH risk scoring system were developed. Potentially serious OSH hazards included: green roofs made of slippery material without fall protection; energy recovery wheels and storm water harvesting systems in confined spaces; skylights without guard rails; and tight geothermal well mechanical rooms constraining safe preventive practices. GB can present PM OSH risks and these should be eliminated in the building design phase. Copyright © 2013 Wiley Periodicals, Inc.

Nuclear component design ontology building based on ASME codes

International Nuclear Information System (INIS)

Bao Shiyi; Zhou Yu; He Shuyan

2005-01-01

The adoption of ontology analysis in the study of concept knowledge acquisition and representation for the nuclear component design process based on computer-supported cooperative work (CSCW) makes it possible to share and reuse numerous concept knowledge of multi-disciplinary domains. A practical ontology building method is accordingly proposed based on Protege knowledge model in combination with both top-down and bottom-up approaches together with Formal Concept Analysis (FCA). FCA exhibits its advantages in the way it helps establish and improve taxonomic hierarchy of concepts and resolve concept conflict occurred in modeling multi-disciplinary domains. With Protege-3.0 as the ontology building tool, a nuclear component design ontology based ASME codes is developed by utilizing the ontology building method. The ontology serves as the basis to realize concept knowledge sharing and reusing of nuclear component design. (authors)

Environmental performance of green building code and certification systems.

Science.gov (United States)

Suh, Sangwon; Tomar, Shivira; Leighton, Matthew; Kneifel, Joshua

2014-01-01

We examined the potential life-cycle environmental impact reduction of three green building code and certification (GBCC) systems: LEED, ASHRAE 189.1, and IgCC. A recently completed whole-building life cycle assessment (LCA) database of NIST was applied to a prototype building model specification by NREL. TRACI 2.0 of EPA was used for life cycle impact assessment (LCIA). The results showed that the baseline building model generates about 18 thousand metric tons CO2-equiv. of greenhouse gases (GHGs) and consumes 6 terajoule (TJ) of primary energy and 328 million liter of water over its life-cycle. Overall, GBCC-compliant building models generated 0% to 25% less environmental impacts than the baseline case (average 14% reduction). The largest reductions were associated with acidification (25%), human health-respiratory (24%), and global warming (GW) (22%), while no reductions were observed for ozone layer depletion (OD) and land use (LU). The performances of the three GBCC-compliant building models measured in life-cycle impact reduction were comparable. A sensitivity analysis showed that the comparative results were reasonably robust, although some results were relatively sensitive to the behavioral parameters, including employee transportation and purchased electricity during the occupancy phase (average sensitivity coefficients 0.26-0.29).

Can envelope codes reduce electricity and CO2 emissions in different types of buildings in the hot climate of Bahrain?

International Nuclear Information System (INIS)

Radhi, H.

2009-01-01

The depletion of non-renewable resources and the environmental impact of energy consumption, particularly energy use in buildings, have awakened considerable interest in energy efficiency. Building energy codes have recently become effective techniques to achieve efficiency targets. The Electricity and Water Authority in Bahrain has set a target of 40% reduction of building electricity consumption and CO 2 emissions to be achieved by using envelope thermal insulation codes. This paper investigates the ability of the current codes to achieve such a benchmark and evaluates their impact on building energy consumption. The results of a simulation study are employed to investigate the impact of the Bahraini codes on the energy and environmental performance of buildings. The study focuses on air-conditioned commercial buildings and concludes that envelope codes, at best, are likely to reduce the energy use of the commercial sector by 25% if the building envelope is well-insulated and efficient glazing is used. Bahraini net CO 2 emissions could drop to around 7.1%. The simulation results show that the current energy codes alone are not sufficient to achieve a 40% reduction benchmark, and therefore, more effort should be spent on moving towards a more comprehensive approach

Effect of URM infills on seismic vulnerability of Indian code designed RC frame buildings

Science.gov (United States)

Haldar, Putul; Singh, Yogendra; Paul, D. K.

2012-03-01

Unreinforced Masonry (URM) is the most common partitioning material in framed buildings in India and many other countries. Although it is well-known that under lateral loading the behavior and modes of failure of the frame buildings change significantly due to infill-frame interaction, the general design practice is to treat infills as nonstructural elements and their stiffness, strength and interaction with the frame is often ignored, primarily because of difficulties in simulation and lack of modeling guidelines in design codes. The Indian Standard, like many other national codes, does not provide explicit insight into the anticipated performance and associated vulnerability of infilled frames. This paper presents an analytical study on the seismic performance and fragility analysis of Indian code-designed RC frame buildings with and without URM infills. Infills are modeled as diagonal struts as per ASCE 41 guidelines and various modes of failure are considered. HAZUS methodology along with nonlinear static analysis is used to compare the seismic vulnerability of bare and infilled frames. The comparative study suggests that URM infills result in a significant increase in the seismic vulnerability of RC frames and their effect needs to be properly incorporated in design codes.

Comparison of SISEC code simulations with earthquake data of ordinary and base-isolated buildings

International Nuclear Information System (INIS)

Wang, C.Y.; Gvildys, J.

1991-01-01

At Argonne National Laboratory (ANL), a 3-D computer program SISEC (Seismic Isolation System Evaluation Code) is being developed for simulating the system response of isolated and ordinary structures (Wang et al. 1991). This paper describes comparison of SISEC code simulations with building response data of actual earthquakes. To ensure the accuracy of analytical simulations, recorded data of full-size reinforced concrete structures located in Sendai, Japan are used in this benchmark comparison. The test structures consist of two three-story buildings, one base-isolated and the other one ordinary founded. They were constructed side by side to investigate the effect of base isolation on the acceleration response. Among 20 earthquakes observed since April 1989, complete records of three representative earthquakes, no.2, no.6, and no.17, are used for the code validation presented in this paper. Correlations of observed and calculated accelerations at all instrument locations are made. Also, relative response characteristics of ordinary and isolated building structures are investigated. (J.P.N.)

Energy conservation: policy issues and end-use scenarios of savings potential. Part V. Energy efficient buildings: the causes of litigation against energy conservation building codes

Energy Technology Data Exchange (ETDEWEB)

Benenson, P.; Codina, R.; Cornwall, B.

1978-09-01

The guidelines laid out for the five subjects investigated in this series are to take a holistic view of energy conservation policies by describing the overall system in which they are implemented; provide analytical tools and sufficiently disagregated data bases that can be adapted to answer a variety of questions by the users; identify and discuss some of the important issues behind successful energy conservation policy; and develop an energy conservation policy in depth. Three specific cases reviewed are: the California nonresidential code (1976); the California residential code (1978); and the Farmers Home Administration code (1978). Although these three suits were brought by the building industry, this report also discusses considerations relevant to architects, bankers, and building inspectors. These cases are discussed from three perspectives: (1) objections to the codes explicitly stated in court, (2) industry conditions and practices behind objections stated in court, and (3) general beliefs not stated in court. This discussion focuses on suits intended to limit those building codes which the building industry sees as too strong. However, some energy conservation industries may sue to strengthen codes which they consider too weak. An example of such a case is Polarized Corporation's current suit against the Lighting section of ASHRAE 90-75 (Los Angeles Federal District Court, see Murnane, 1978). (MCW)

Building America Guidance for Identifying and Overcoming Code, Standard, and Rating Method Barriers

Energy Technology Data Exchange (ETDEWEB)

Cole, P. C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Halverson, M. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2013-09-01

This guidance document was prepared using the input from the meeting summarized in the draft CSI Roadmap to provide Building America research teams and partners with specific information and approaches to identifying and overcoming potential barriers to Building America innovations arising in and/or stemming from codes, standards, and rating methods.

Capturing Energy-Saving Opportunities: Improving Building Efficiency in Rajasthan through Energy Code Implementation

Energy Technology Data Exchange (ETDEWEB)

Tan, Qing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Yu, Sha [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Evans, Meredydd [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mathur, Jyotirmay [Malaviya National Institute of Technology, Jaipur (India); Vu, Linh D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-05-01

India adopted the Energy Conservation Building Code (ECBC) in 2007. Rajasthan is the first state to make ECBC mandatory at the state level. In collaboration with Malaviya National Institute of Technology (MNIT) Jaipur, Pacific Northwest National Laboratory (PNNL) has been working with Rajasthan to facilitate the implementation of ECBC. This report summarizes milestones made in Rajasthan and PNNL's contribution in institutional set-ups, capacity building, compliance enforcement and pilot building construction.

Analysis of Potential Benefits and Costs of Updating the Commercial Building Energy Code in Iowa

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Belzer, David B.; Richman, Eric E.; Winiarski, David W.

2002-09-07

The state of Iowa is considering adpoting ASHRAE 90.1-1999 as its commercial building energy code. In an effort to evaluate whether or not this is an appropraite code for the state, the potential benefits and costs of adopting this standard are considered. Both qualitative and quantitative benefits are assessed. The energy simulation and economic results suggest that adopting ASHRAE 90.1-1999 would provide postitive net benefits to the state relative to the building and design requirements currently in place.

Safe operation of critical assemblies and research reactors. Code of practice and Technical appendix. 1971 ed

International Nuclear Information System (INIS)

Cox, J.

1971-01-01

This book is in two parts. The first is a Code of Practice for the Safe Operation of Critical Assemblies and Research Reactors, prepared as a result of a meeting of experts which took place in Vienna on 20-24 May 1968. The Code has been prepared by the International Atomic Energy Agency in co-operation with the World Health Organization, and its publication is sponsored by both organizations. In addition, the Code was approved by the Board of Governors of the International Atomic Energy Agency on 16 December 1968 as part of the Agency's safety standards, which are applied to operations undertaken by Member States with the assistance of the Agency. The Board, in approving the publication of the present book, also recommended Member States to take the Code into account in the formulation of national regulations and recommendations. The second part of the book is a Technical Appendix to give information and illustrative samples that would be helpful in implementing the Code of Practice. This second part, although published under the same cover, is not part of the Code. An extensive Bibliography, amplifying the Technical Appendix, is included at the end.

European Model Code of safe practice in the storage and handling of petroleum products. Part I. Operations

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

This safe practice code was prepared by a working group consisting of experts from 10 Western European countries. It consists of short guidelines and technical advice on general precautions, injuries and medical services, permits to work, fire prevention and fighting, jetties, pipework, storage tanks, static electricity, electrical equipment, road vehicles, tank cars, handling of bitumen products, liquefied petroleum gases, packed products and training of personnel. The code is supplemented by 10 appendices, including a suggested syllabus for a 2-day course on fire prevention and emergency action for managers of oil installations.

Building energy performance analysis by an in-house developed dynamic simulation code: An investigation for different case studies

International Nuclear Information System (INIS)

Buonomano, Annamaria; Palombo, Adolfo

2014-01-01

Highlights: • A new dynamic simulation code for building energy performance analysis is presented. • The thermal behavior of each building element is modeled by a thermal RC network. • The physical models implemented in the code are illustrated. • The code was validated by the BESTEST standard procedure. • We investigate residential buildings, offices and stores in different climates. - Abstract: A novel dynamic simulation model for the building envelope energy performance analysis is presented in this paper. This tool helps the investigation of many new building technologies to increase the system energy efficiency and it can be carried out for scientific research purposes. In addition to the yearly heating and cooling load and energy demand, the obtained output is the dynamic temperature profile of indoor air and surfaces and the dynamic profile of the thermal fluxes through the building elements. The presented simulation model is also validated through the BESTEST standard procedure. Several new case studies are developed for assessing, through the presented code, the energy performance of three different building envelopes with several different weather conditions. In particular, dwelling and commercial buildings are analysed. Light and heavyweight envelopes as well as different glazed surfaces areas have been used for every case study. With the achieved results interesting design and operating guidelines can be obtained. Such data have been also compared vs. those calculated by TRNSYS and EnergyPlus. The detected deviation of the obtained results vs. those of such standard tools are almost always lower than 10%

DroidSafe

Science.gov (United States)

2016-12-01

Massachusetts Avenue, Build E19-750 Cambridge , MA 02139-4307 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS...Activity objects illustrating the challenges of points-to and information flow analysis...measure how many malicious flows Droid- Safe was able to detect). As these results illustrate , DroidSafe implements an analysis of unprece- dented

Estimation of skyshine dose from turbine building of BWR plant using Monte Carlo code

Energy Technology Data Exchange (ETDEWEB)

Yuji, Nemoto; Toshihisa, Tsukiyama; Shigeki, Nemezawa [Hitachi. Ltd., Saiwai-cho, Hitachi (Japan); Tadashi, Yamasaki; Hidetsugu, Okada [Chubu Electric Power Company, Inc., Odaka-cho, Midori-ku Nagoya (Japan)

2007-07-01

The Monte Carlo N-Particle transport code (MCNP) was adopted to calculate the skyshine dose from the turbine building of a BWR plant for obtaining precise estimations at the site boundary. In MCNP calculation, the equipment and piping arranged on the operating floor of the turbine building were considered and modeled in detail. The inner and outer walls of the turbine building, the shielding materials around the high-pressure turbine, and the piping connected from the moisture separator to the low-pressure turbine were all considered. A three-step study was conducted to estimate the applicability of MCNP code. The first step is confirming the propriety of calculation models. The atmospheric relief diaphragms, which are installed on top of the low-pressure turbine exhaust hood, are not considered in the calculation model. There was little difference between the skyshine dose distributions that were considered when using and not using the atmospheric relief diaphragms. The calculated dose rates agreed well with the measurements taken around the turbine. The second step is estimating the dose rates on the outer roof surface of the turbine building. This calculation was made to confirm the dose distribution of gamma-rays on the turbine roof before being scattered into the air. The calculated dose rates agreed well with the measured data. The third step is making a final confirmation by comparing the calculations and measurements of skyshine dose rates around the turbine building. The source terms of the main steam system are based on the measured activity data of N-16 and C-15. As a conclusion, we were able to calculate reasonable skyshine dose rates by using MCNP code. (authors)

Deregulation of the Building Code and the Norwegian Approach to Regulation of Accessibility in the Built Environment.

Science.gov (United States)

Lyngstad, Pål

2016-01-01

Deregulation is on the political agenda in the European countries. The Norwegian building code related to universal design and accessibility is challenged. To meet this, the Norwegian Building Authority have chosen to examine established truths and are basing their revised code on scientific research and field tests. But will this knowledge-based deregulation comply within the framework of the anti-discrimination act and, and if not: who suffers and to what extent?

Learning by Doing: Teaching Decision Making through Building a Code of Ethics.

Science.gov (United States)

Hawthorne, Mark D.

2001-01-01

Notes that applying abstract ethical principles to the practical business of building a code of applied ethics for a technical communication department teaches students that they share certain unarticulated or unconscious values that they can translate into ethical principles. Suggests that combining abstract theory with practical policy writing…

Energy and Environment Guide to Action - Chapter 4.3: Building Codes for Energy Efficiency

Science.gov (United States)

Provides guidance and recommendations for establishing, implementing, and evaluating state building codes for energy efficiency, which improve energy efficiency in new construction and major renovations. State success stories are included for reference.

Assessment of codes, by-laws and regulations relating to air wells in building design

Science.gov (United States)

Fadzil, Sharifah Fairuz Syed; Karamazaman, Nazli

2017-10-01

Codes and by-laws concerning air well design (for buildings and lavatories) in Malaysia has been established in the Malaysian Uniform Building By-Laws UBBL number 40 (1) and (2) since the 1980s. Wells are there to fulfill the ventilation and daylighting requirements. The minimum well area according to building storey height are compared between UBBL and the Singapore's well requirements from the Building Construction Authority BCA. A visual and graphical representation (with schematics building and well diagrams drawn to scale) of the minimum well sizes and dimensions is given. It can be seen that if the minimum requirement of well size is used for buildings above 8 storeys high, a thin well resulted which is not proportionate to the building height. A proposed dimension is graphed and given to be used in the UBBL which translated to graphics (3 dimensional buildings drawn to scale) created a much better well proportion.

Code of practice for the control and safe handling of radioactive sources used for therapeutic purposes (1988)

International Nuclear Information System (INIS)

1988-01-01

This Code is intended as a guide to safe practices in the use of sealed and unsealed radioactive sources and in the management of patients being treated with them. It covers the procedures for the handling, preparation and use of radioactive sources, precautions to be taken for patients undergoing treatment, storage and transport of radioactive sources within a hospital or clinic, and routine testing of sealed sources [fr

Energy Code Compliance in a Detailed Commercial Building Sample: The Effects of Missing Data

Energy Technology Data Exchange (ETDEWEB)

Biyani, Rahul K.; Richman, Eric E.

2003-09-30

Most commercial buildings in the U.S. are required by State or local jurisdiction to meet energy standards. The enforcement of these standards is not well known and building practice without them on a national scale is also little understood. To provide an understanding of these issues, a database has been developed at PNNL that includes detailed energy related building characteristics of 162 commercial buildings from across the country. For this analysis, the COMcheck? compliance software (developed at PNNL) was used to assess compliance with energy codes among these buildings. Data from the database for each building provided the program input with percentage energy compliance to the ASHRAE/IESNA Standard 90.1-1999 energy as the output. During the data input process it was discovered that some essential data for showing compliance of the building envelope was missed and defaults had to be developed to provide complete compliance information. This need for defaults for some data inputs raised the question of what the effect on documenting compliance could be due to missing data. To help answer this question a data collection effort was completed to assess potential differences. Using the program Dodge View, as much of the missing envelope data as possible was collected from the building plans and the database input was again run through COMcheck?. The outputs of both compliance runs were compared to see if the missing data would have adversely affected the results. Both of these results provided a percentage compliance of each building in the envelope and lighting categories, showing by how large a percentage each building either met or fell short of the ASHRAE/IESNA Standard 90.1-1999 energy code. The results of the compliance runs showed that 57.7 % of the buildings met or exceeded envelope requirements with defaults and that 68 % met or exceeded envelope requirements with the actual data. Also, 53.6 % of the buildings met or surpassed the lighting requirements

Main building fire drill safely concluded

CERN Document Server

CERN Bulletin

2015-01-01

Last week, a simulated fire in the stairwell of the Main Building put CERN’s emergency response procedures to the test.   Firefighters descend the stairwell in the Main Building as the simulated fire rises.   At 2 p.m. on 22 September, alarms sounded around CERN’s Main Building as an evacuation exercise got underway. A simulated fire in the  stairwell, complete with very realistic smoke, led to the evacuation of one of the busiest places at CERN. The Main Building complex includes the Carlson Wagonlit travel agency, the post office, UBS, Uniqa, the Users Office, the Staff Association and the Novae restaurant as well as the Main Auditorium, the Council Chamber and the Charpak meeting room. It was impressive to see how quickly the smoke propagated in the staircase as well as into the corridors, and equally impressive to see how smoothly, quickly and efficiently the evacuation proceeded. The...

Final Hazard Classification and Auditable Safety Analysis for the 105-F Building Interim Safe Storage Project

International Nuclear Information System (INIS)

Rodovsky, T.J.; Bond, S.L.

1998-07-01

The auditable safety analysis (ASA) documents the authorization basis for the partial decommissioning and facility modifications to place the 105-F Building into interim safe storage (ISS). Placement into the ISS is consistent with the preferred alternative identified in the Record of Decision (58 FR). Modifications will reduce the potential for release and worker exposure to hazardous and radioactive materials, as well as lower surveillance and maintenance (S ampersand M) costs. This analysis includes the following: A description of the activities to be performed in the course of the 105-F Building ISS Project. An assessment of the inventory of radioactive and other hazardous materials within the 105-F Building. Identification of the hazards associated with the activities of the 105-F Building ISS Project. Identification of internally and externally initiated accident scenarios with the potential to produce significant local or offsite consequences during the 105-F Building ISS Project. Bounding evaluation of the consequences of the potentially significant accident scenarios. Hazard classification based on the bounding consequence evaluation. Associated safety function and controls, including commitments. Radiological and other employee safety and health considerations

Assessment of the Portuguese building thermal code: Newly revised requirements for cooling energy needs used to prevent the overheating of buildings in the summer

International Nuclear Information System (INIS)

Oliveira Panao, Marta J.N.; Camelo, Susana M.L.; Goncalves, Helder J.P.

2011-01-01

In this paper, cooling energy needs are calculated by the steady-state methodology of the Portuguese building thermal code. After the first period of building code implementation, re-evaluation according to EN ISO 13790 is recommended in order to compare results with the dynamic simulation results. From these analyses, a newly revised methodology arises including a few corrections in procedure. This iterative result is sufficiently accurate to calculate the building's cooling energy needs. Secondly, results show that the required conditions are insufficient to prevent overheating. The use of the gain utilization factor as an overheating risk index is suggested, according to an adaptive comfort protocol, and is integrated in the method used to calculate the maximum value for cooling energy needs. This proposed streamlined method depends on reference values: window-to-floor area ratio, window shading g-value, integrated solar radiation and gain utilization factor, which leads to threshold values significantly below the ones currently used. These revised requirements are more restrictive and, therefore, will act to improve a building's thermal performance during summer. As a rule of thumb applied for Portuguese climates, the reference gain utilization factor should assume a minimum value of 0.8 for a latitude angle range of 40-41 o N, 0.6 for 38-39 o N and 0.5 for 37 o N. -- Highlights: → A newly revised methodology for Portuguese building thermal code. → The use of the gain utilization factor as an overheating risk index is suggested. → The proposed streamlined method depends on reference values. → Threshold maximum values are significantly below the ones currently used.

Removal Action Work Plan for 105-DR and 105-F Building Interim Safe Storage Projects and Ancillary Buildings

International Nuclear Information System (INIS)

Morton, M.R.

2000-01-01

This document contains the removal action work plan for the 105-DR and 105-F Reactor buildings and ancillary facilities. These buildings and facilities are located in the 100-D/DR and 100-F Areas of the Hanford Site, which is owned and operated by the US Department of Energy (DOE), in Benton County, Washington. The 100 Areas (including the 100-D/DR and 100-F Areas) of the Hanford Site were placed on the US Environmental Protection Agency's (EPA's) National Priorities List under the ''Comprehensive Environmental Response, Compensation, and Liability Act of 1980'' (CERCLA). The DOE has determined that hazardous substances in the 105-DR and 105-F Reactor buildings and four ancillary facilities present a potential threat to human health or the environment. The DOE has also determined that a non-time critical removal action is warranted at these facilities. Alternatives for conducting a non-time critical removal action were evaluated in the ''Engineering Evaluation/Cost Analysis for the 105-DR and 105-F Reactor Facilities and Ancillary Facilities'' (DOE-RL 1998a). The engineering evaluation/cost analysis (EE/CA) resulted in the recommendation to decontaminate and demolish the contaminated reactor buildings (except for the reactor blocks) and the ancillary facilities and to construct a safe storage enclosure (SSE) over the reactor blocks. The recommendation was approved in an action memorandum (Ecology et al. 1998) signed by the Washington State Department of Ecology (Ecology), EPA, and DOE. The DOE is the agency responsible for implementing the removal actions in the 105-D/DR and 105-F Areas. Ecology is the lead regulatory agency for facilities in the 100-D/DR Area, and EPA is the lead regulatory agency for facilities in the 100-F Area. The term ''lead regulator agency'' hereinafter, refers to these authorities. This removal action work plan supports implementation of the non-time critical removal action

49 CFR 41.120 - Acceptable model codes.

Science.gov (United States)

2010-10-01

... 1991 International Conference of Building Officials (ICBO) Uniform Building Code, published by the... Supplement to the Building Officials and Code Administrators International (BOCA) National Building Code, published by the Building Officials and Code Administrators, 4051 West Flossmoor Rd., Country Club Hills...

Updates to building-code maps for the 2015 NEHRP recommended seismic provisions

Science.gov (United States)

Luco, Nicolas; Bachman, Robert; Crouse, C.B; Harris, James R.; Hooper, John D.; Kircher, Charles A.; Caldwell, Phillp; Rukstales, Kenneth S.

2015-01-01

With the 2014 update of the U.S. Geological Survey (USGS) National Seismic Hazard Model (NSHM) as a basis, the Building Seismic Safety Council (BSSC) has updated the earthquake ground motion maps in the National Earthquake Hazards Reduction Program (NEHRP) Recommended Seismic Provisions for New Buildings and Other Structures, with partial funding from the Federal Emergency Management Agency. Anticipated adoption of the updated maps into the American Society of Civil Engineers Minimum Design Loads for Building and Other Structures and the International Building and Residential Codes is underway. Relative to the ground motions in the prior edition of each of these documents, most of the updated values are within a ±20% change. The larger changes are, in most cases, due to the USGS NSHM updates, reasons for which are given in companion publications. In some cases, the larger changes are partly due to a BSSC update of the slope of the fragility curve that is used to calculate the risk-targeted ground motions, and/or the introduction by BSSC of a quantitative definition of “active faults” used to calculate deterministic ground motions.

Civil Behavior, Safe-School Planning, and Dress Codes

Science.gov (United States)

Studak, Cathryn M.; Workman, Jane E.

2007-01-01

This research examined news reports in order to identify incidents that precipitated dress code revisions. News reports were examined within the framework of rules for civil behavior. Using key words "school dress codes" and "violence," LEXIS/NEXIS was used to access 104 articles from 44 U.S. newspapers from December 3, 2004 to December 2, 2005.…

24 CFR 200.925c - Model codes.

Science.gov (United States)

2010-04-01

... below. (1) Model Building Codes—(i) The BOCA National Building Code, 1993 Edition, The BOCA National..., Administration, for the Building, Plumbing and Mechanical Codes and the references to fire retardant treated wood... number 2 (Chapter 7) of the Building Code, but including the Appendices of the Code. Available from...

Analysis of Potential Benefits and Costs of Adopting ASHRAE Standard 90.1-2001 as the Commercial Building Energy Code in Tennessee

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Winiarski, David W.; Belzer, David B.; Richman, Eric E.

2004-09-30

ASHRAE Standard 90.1-2001 Energy Standard for Buildings except Low-Rise Residential Buildings (hereafter referred to as ASHRAE 90.1-2001 or 90.1-2001) was developed in an effort to set minimum requirements for the energy efficient design and construction of new commercial buildings. The State of Tennessee is considering adopting ASHRAE 90.1-2001 as its commercial building energy code. In an effort to evaluate whether or not this is an appropriate code for the state, the potential benefits and costs of adopting this standard are considered in this report. Both qualitative and quantitative benefits and costs are assessed. Energy and economic impacts are estimated using the Building Loads Analysis and System Thermodynamics (BLAST) simulations combined with a Life-Cycle Cost (LCC) approach to assess corresponding economic costs and benefits. Tennessee currently has ASHRAE Standard 90A-1980 as the statewide voluntary/recommended commercial energy standard; however, it is up to the local jurisdiction to adopt this code. Because 90A-1980 is the recommended standard, many of the requirements of ASHRAE 90A-1980 were used as a baseline for simulations.

INCAS residential building energy savings design code: User's guide. INCAS: guida all'uso del codice di calcolo di diagnosi energetica nell'abitazione

Energy Technology Data Exchange (ETDEWEB)

Carderi, A.

1991-01-01

The INCAS residential building energy savings design code comes complete with data banks giving designers all the necessary technical and economic information and energy savings options for the code's efficacious application to obtain the optimum energy efficient/cost beneficial solution. This user's manual contains descriptions of the types of data to be input, the code's methodology, the data banks, and complete instructions for the code's implementation. The energy savings alternatives include: choice of heating plant and fuel; choice, application location and thickness of thermal insulation. For the case of building heating system retrofits, the code takes into account the existing condition of building components.

Locally orderless registration code

DEFF Research Database (Denmark)

2012-01-01

This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows.......This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows....

Code of conduct for scientists (abstract)

International Nuclear Information System (INIS)

Khurshid, S.J.

2011-01-01

The emergence of advanced technologies in the last three decades and extraordinary progress in our knowledge on the basic Physical, Chemical and Biological properties of living matter has offered tremendous benefits to human beings but simultaneously highlighted the need of higher awareness and responsibility by the scientists of 21 century. Scientist is not born with ethics, nor science is ethically neutral, but there are ethical dimensions to scientific work. There is need to evolve an appropriate Code of Conduct for scientist particularly working in every field of Science. However, while considering the contents, promulgation and adaptation of Codes of Conduct for Scientists, a balance is needed to be maintained between freedom of scientists and at the same time some binding on them in the form of Code of Conducts. The use of good and safe laboratory procedures, whether, codified by law or by common practice must also be considered as part of the moral duties of scientists. It is internationally agreed that a general Code of Conduct can't be formulated for all the scientists universally, but there should be a set of 'building blocks' aimed at establishing the Code of Conduct for Scientists either as individual researcher or responsible for direction, evaluation, monitoring of scientific activities at the institutional or organizational level. (author)

Seismic Safety Of Simple Masonry Buildings

International Nuclear Information System (INIS)

Guadagnuolo, Mariateresa; Faella, Giuseppe

2008-01-01

Several masonry buildings comply with the rules for simple buildings provided by seismic codes. For these buildings explicit safety verifications are not compulsory if specific code rules are fulfilled. In fact it is assumed that their fulfilment ensures a suitable seismic behaviour of buildings and thus adequate safety under earthquakes. Italian and European seismic codes differ in the requirements for simple masonry buildings, mostly concerning the building typology, the building geometry and the acceleration at site. Obviously, a wide percentage of buildings assumed simple by codes should satisfy the numerical safety verification, so that no confusion and uncertainty have to be given rise to designers who must use the codes. This paper aims at evaluating the seismic response of some simple unreinforced masonry buildings that comply with the provisions of the new Italian seismic code. Two-story buildings, having different geometry, are analysed and results from nonlinear static analyses performed by varying the acceleration at site are presented and discussed. Indications on the congruence between code rules and results of numerical analyses performed according to the code itself are supplied and, in this context, the obtained result can provide a contribution for improving the seismic code requirements

Analysis of Potential Benefits and Costs of Updating the Commercial Building Energy Code in North Dakota

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Belzer, David B.; Winiarski, David W.; Richman, Eric E.

2004-04-30

The state of North Dakota is considering updating its commercial building energy code. This report evaluates the potential costs and benefits to North Dakota residents from updating and requiring compliance with ASHRAE Standard 90.1-2001. Both qualitative and quantitative benefits and costs are assessed in the analysis. Energy and economic impacts are estimated using the Building Loads Analysis and System Thermodynamics (BLAST simulation combined with a Life-cycle Cost (LCC) approach to assess correspodning economic costs and benefits.

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

Science.gov (United States)

Toprak, A. Emre; Gülay, F. Gülten; Ruge, Peter

2008-07-01

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performed on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 m×7.80 m = 127.90 m2 with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher

Comparative Study on Code-based Linear Evaluation of an Existing RC Building Damaged during 1998 Adana-Ceyhan Earthquake

International Nuclear Information System (INIS)

Toprak, A. Emre; Guelay, F. Guelten; Ruge, Peter

2008-01-01

Determination of seismic performance of existing buildings has become one of the key concepts in structural analysis topics after recent earthquakes (i.e. Izmit and Duzce Earthquakes in 1999, Kobe Earthquake in 1995 and Northridge Earthquake in 1994). Considering the need for precise assessment tools to determine seismic performance level, most of earthquake hazardous countries try to include performance based assessment in their seismic codes. Recently, Turkish Earthquake Code 2007 (TEC'07), which was put into effect in March 2007, also introduced linear and non-linear assessment procedures to be applied prior to building retrofitting. In this paper, a comparative study is performed on the code-based seismic assessment of RC buildings with linear static methods of analysis, selecting an existing RC building. The basic principles dealing the procedure of seismic performance evaluations for existing RC buildings according to Eurocode 8 and TEC'07 will be outlined and compared. Then the procedure is applied to a real case study building is selected which is exposed to 1998 Adana-Ceyhan Earthquake in Turkey, the seismic action of Ms = 6.3 with a maximum ground acceleration of 0.28 g It is a six-storey RC residential building with a total of 14.65 m height, composed of orthogonal frames, symmetrical in y direction and it does not have any significant structural irregularities. The rectangular shaped planar dimensions are 16.40 mx7.80 m = 127.90 m 2 with five spans in x and two spans in y directions. It was reported that the building had been moderately damaged during the 1998 earthquake and retrofitting process was suggested by the authorities with adding shear-walls to the system. The computations show that the performing methods of analysis with linear approaches using either Eurocode 8 or TEC'07 independently produce similar performance levels of collapse for the critical storey of the structure. The computed base shear value according to Eurocode is much higher

Lessons learned from new construction utility demand side management programs and their implications for implementing building energy codes

Energy Technology Data Exchange (ETDEWEB)

Wise, B.K.; Hughes, K.R.; Danko, S.L.; Gilbride, T.L.

1994-07-01

This report was prepared for the US Department of Energy (DOE) Office of Codes and Standards by the Pacific Northwest Laboratory (PNL) through its Building Energy Standards Program (BESP). The purpose of this task was to identify demand-side management (DSM) strategies for new construction that utilities have adopted or developed to promote energy-efficient design and construction. PNL conducted a survey of utilities and used the information gathered to extrapolate lessons learned and to identify evolving trends in utility new-construction DSM programs. The ultimate goal of the task is to identify opportunities where states might work collaboratively with utilities to promote the adoption, implementation, and enforcement of energy-efficient building energy codes.

Analysis of Potential Benefits and Costs of Adopting ASHRAE Standard 90.1-1999 as a Commercial Building Energy Code in Michigan

Energy Technology Data Exchange (ETDEWEB)

Cort, Katherine A.; Belzer, David B.; Halverson, Mark A.; Richman, Eric E.; Winiarski, David W.

2002-09-30

The state of Michigan is considering adpoting ASHRAE 90.1-1999 as its commercial building energy code. In an effort to evaluate whether or not this is an appropraite code for the state, the potential benefits and costs of adopting this standard are considered. Both qualitative and quantitative benefits are assessed. The energy simulation and economic results suggest that adopting ASHRAE 90.1-1999 would provide postitive net benefits to the state relative to the building and design requirements currently in place.

Radioactive action code

International Nuclear Information System (INIS)

Anon.

1988-01-01

A new coding system, 'Hazrad', for buildings and transportation containers for alerting emergency services personnel to the presence of radioactive materials has been developed in the United Kingdom. The hazards of materials in the buildings or transport container, together with the recommended emergency action, are represented by a number of codes which are marked on the building or container and interpreted from a chart carried as a pocket-size guide. Buildings would be marked with the familiar yellow 'radioactive' trefoil, the written information 'Radioactive materials' and a list of isotopes. Under this the 'Hazrad' code would be written - three symbols to denote the relative radioactive risk (low, medium or high), the biological risk (also low, medium or high) and the third showing the type of radiation emitted, alpha, beta or gamma. The response cards indicate appropriate measures to take, eg for a high biological risk, Bio3, the wearing of a gas-tight protection suit is advised. The code and its uses are explained. (U.K.)

VS30 – A site-characterization parameter for use in building Codes, simplified earthquake resistant design, GMPEs, and ShakeMaps

Science.gov (United States)

Borcherdt, Roger D.

2012-01-01

VS30, defined as the average seismic shear-wave velocity from the surface to a depth of 30 meters, has found wide-spread use as a parameter to characterize site response for simplified earthquake resistant design as implemented in building codes worldwide. VS30 , as initially introduced by the author for the US 1994 NEHRP Building Code, provides unambiguous definitions of site classes and site coefficients for site-dependent response spectra based on correlations derived from extensive borehole logging and comparative ground-motion measurement programs in California. Subsequent use of VS30 for development of strong ground motion prediction equations (GMPEs) and measurement of extensive sets of VS borehole data have confirmed the previous empirical correlations and established correlations of SVS30 with VSZ at other depths. These correlations provide closed form expressions to predict S30 V at a large number of additional sites and further justify S30 V as a parameter to characterize site response for simplified building codes, GMPEs, ShakeMap, and seismic hazard mapping.

Code of practice : safe use of ionizing radiation

International Nuclear Information System (INIS)

1988-07-01

Ionizing radiation is used extensively in the field of scientific research. The risk of uncontrolled exposure to both the worker and the environment is ever present. The purpose of this Code is to set out practices considered by the CSIRO Health and Safety Committee to be appropriate for CSIRO staff and, if followed, they will result in appropriate protection for research staff and the environment. The Code does not cover sources of non-ionizing radiation such as microwave ovens, RF generators and laser sources

RESRAD-BUILD verification

International Nuclear Information System (INIS)

Kamboj, S.; Yu, C.; Biwer, B. M.; Klett, T.

2002-01-01

The results generated by the RESRAD-BUILD code (version 3.0) were verified with hand or spreadsheet calculations using equations given in the RESRAD-BUILD manual for different pathways. For verification purposes, different radionuclides--H-3, C-14, Na-22, Al-26, Cl-36, Mn-54, Co-60, Au-195, Ra-226, Ra-228, Th-228, and U-238--were chosen to test all pathways and models. Tritium, Ra-226, and Th-228 were chosen because of the special tritium and radon models in the RESRAD-BUILD code. Other radionuclides were selected to represent a spectrum of radiation types and energies. Verification of the RESRAD-BUILD code was conducted with an initial check of all the input parameters for correctness against their original source documents. Verification of the calculations was performed external to the RESRAD-BUILD code with Microsoft Excel to verify all the major portions of the code. In some cases, RESRAD-BUILD results were compared with those of external codes, such as MCNP (Monte Carlo N-particle) and RESRAD. The verification was conducted on a step-by-step basis and used different test cases as templates. The following types of calculations were investigated: (1) source injection rate, (2) air concentration in the room, (3) air particulate deposition, (4) radon pathway model, (5) tritium model for volume source, (6) external exposure model, (7) different pathway doses, and (8) time dependence of dose. Some minor errors were identified in version 3.0; these errors have been corrected in later versions of the code. Some possible improvements in the code were also identified

Safe use of ionizing radiations

Energy Technology Data Exchange (ETDEWEB)

1973-01-01

Based on the ''Code of Practice for the protection of persons against ionizing radiations arising from medical and dental use'' (CIS 74-423), this handbook shows how hospital staff can avoid exposing themselves and others to these hazards. It is designed particularly for junior and student nurses. Contents: ionizing radiations, their types and characteristics; their uses and dangers; basic principles in their safe use; safe use in practice; explanation of terms.

Building guide : how to build Xyce from source code.

Energy Technology Data Exchange (ETDEWEB)

Keiter, Eric Richard; Russo, Thomas V.; Schiek, Richard Louis; Sholander, Peter E.; Thornquist, Heidi K.; Mei, Ting; Verley, Jason C.

2013-08-01

While Xyce uses the Autoconf and Automake system to configure builds, it is often necessary to perform more than the customary %E2%80%9C./configure%E2%80%9D builds many open source users have come to expect. This document describes the steps needed to get Xyce built on a number of common platforms.

78 FR 18321 - International Code Council: The Update Process for the International Codes and Standards

Science.gov (United States)

2013-03-26

... Energy Conservation Code. International Existing Building Code. International Fire Code. International... Code. International Property Maintenance Code. International Residential Code. International Swimming Pool and Spa Code International Wildland-Urban Interface Code. International Zoning Code. ICC Standards...

INLUX-DBR - A calculation code to calculate indoor natural illuminance inside buildings under various sky conditions

International Nuclear Information System (INIS)

Ferraro, V.; Igawa, N.; Marinelli, V.

2010-01-01

A calculation code, named INLUX-DBR, is presented, which is a modified version of INLUX code, able to predict the illuminance distribution on the inside surfaces of a room with six walls and a window, and on the work plane. At each desired instant the code solves the system of the illuminance equations of each surface element, characterized by the latter's reflection coefficient and its view factors toward the other elements. In the model implemented in the code, the sky-diffuse luminance distribution, the sun beam light and the light reflected from the ground toward the room are considered. The code was validated by comparing the calculated values of illuminance with the experimental values measured inside a scale model (1:5) of a building room, in various sky conditions of overcast, clear and intermediate days. The validation is performed using the sky luminance data measured by a sky scanner and the measured beam illuminance of the sun as input data. A comparative analysis of some of the well-known calculation models of sky luminance, namely Perez, Igawa and CIE models was also carried out, comparing the code predictions and the measured values of inside illuminance in the scale model.

Energy Efficiency Building Code for Commercial Buildings in Sri Lanka

Energy Technology Data Exchange (ETDEWEB)

Busch, John; Greenberg, Steve; Rubinstein, Francis; Denver, Andrea; Rawner, Esther; Franconi, Ellen; Huang, Joe; Neils, Danielle

2000-09-30

1.1.1 To encourage energy efficient design or retrofit of commercial buildings so that they may be constructed, operated, and maintained in a manner that reduces the use of energy without constraining the building function, the comfort, health, or the productivity of the occupants and with appropriate regard for economic considerations. 1.1.2 To provide criterion and minimum standards for energy efficiency in the design or retrofit of commercial buildings and provide methods for determining compliance with them. 1.1.3 To encourage energy efficient designs that exceed these criterion and minimum standards.

Energy Efficiency Building Code for Commercial Buildings in Sri Lanka

International Nuclear Information System (INIS)

Busch, John; Greenberg, Steve; Rubinstein, Francis; Denver, Andrea; Rawner, Esther; Franconi, Ellen; Huang, Joe; Neils, Danielle

2000-01-01

1.1.1 To encourage energy efficient design or retrofit of commercial buildings so that they may be constructed, operated, and maintained in a manner that reduces the use of energy without constraining the building function, the comfort, health, or the productivity of the occupants and with appropriate regard for economic considerations. 1.1.2 To provide criterion and minimum standards for energy efficiency in the design or retrofit of commercial buildings and provide methods for determining compliance with them. 1.1.3 To encourage energy efficient designs that exceed these criterion and minimum standards

PIConGPU - How to build one of the fastest GPU particle-in-cell codes in the world

Energy Technology Data Exchange (ETDEWEB)

Burau, Heiko; Debus, Alexander; Helm, Anton; Huebl, Axel; Kluge, Thomas; Widera, Rene; Bussmann, Michael; Schramm, Ulrich; Cowan, Thomas [HZDR, Dresden (Germany); Juckeland, Guido; Nagel, Wolfgang [TU Dresden (Germany); ZIH, Dresden (Germany); Schmitt, Felix [NVIDIA (United States)

2013-07-01

We present the algorithmic building blocks of PIConGPU, one of the fastest implementations of the particle-in-cell algortihm on GPU clusters. PIConGPU is a highly-scalable, 3D3V electromagnetic PIC code that is used in laser plasma and astrophysical plasma simulations.

Training program for energy conservation in new building construction. Volume III. Energy conservation technology for plan examiners and code administrators. Energy Conservation Technology Series 200

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

Under the sponsorship of the United States Department of Energy, a Model Code for Energy Conservation in New Building Construction has been developed by those national organizations primarily concerned with the development and promulgation of model codes. The technical provisions are based on ASHRAE Standard 90-75 and are intended for use by state and local officials. The subject of regulation of new building construction to assure energy conservation is recognized as one in which code officials have not had previous exposure. It was also determined that application of the model code would be made at varying levels by officials with both a specific requirement for knowledge and a differing degree of prior training in the state-of-the-art. Therefore, a training program and instructional materials were developed for code officials to assist them in the implementation and enforcement of energy efficient standards and codes. The training program for Energy Conservation Tehnology for Plan Examiners and Code Administrators (ECT Series 200) is presented.

75 FR 19944 - International Code Council: The Update Process for the International Codes and Standards

Science.gov (United States)

2010-04-16

... documents from ICC's Chicago District Office: International Code Council, 4051 W Flossmoor Road, Country... Energy Conservation Code. International Existing Building Code. International Fire Code. International...

Interrelations of codes in human semiotic systems.

OpenAIRE

Somov, Georgij

2016-01-01

Codes can be viewed as mechanisms that enable relations of signs and their components, i.e., semiosis is actualized. The combinations of these relations produce new relations as new codes are building over other codes. Structures appear in the mechanisms of codes. Hence, codes can be described as transformations of structures from some material systems into others. Structures belong to different carriers, but exist in codes in their "pure" form. Building of codes over other codes fosters t...

Energy Savings Analysis of the Proposed NYStretch-Energy Code 2018

Energy Technology Data Exchange (ETDEWEB)

Liu, Bing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhang, Jian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chen, Yan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Edelson, Jim [New Buildings Inst. (NBI), Portland, OR (United States); Lyles, Mark [New Buildings Inst. (NBI), Portland, OR (United States)

2018-01-20

This study was conducted by the Pacific Northwest National Laboratory (PNNL) in support of the stretch energy code development led by the New York State Energy Research and Development Authority (NYSERDA). In 2017 NYSERDA developed its 2016 Stretch Code Supplement to the 2016 New York State Energy Conservation Construction Code (hereinafter referred to as “NYStretch-Energy”). NYStretch-Energy is intended as a model energy code for statewide voluntary adoption that anticipates other code advancements culminating in the goal of a statewide Net Zero Energy Code by 2028. Since then, NYSERDA continues to develop the NYStretch-Energy Code 2018 edition. To support the effort, PNNL conducted energy simulation analysis to quantify the energy savings of proposed commercial provisions of the NYStretch-Energy Code (2018) in New York. The focus of this project is the 20% improvement over existing commercial model energy codes. A key requirement of the proposed stretch code is that it be ‘adoptable’ as an energy code, meaning that it must align with current code scope and limitations, and primarily impact building components that are currently regulated by local building departments. It is largely limited to prescriptive measures, which are what most building departments and design projects are most familiar with. This report describes a set of energy-efficiency measures (EEMs) that demonstrate 20% energy savings over ANSI/ASHRAE/IES Standard 90.1-2013 (ASHRAE 2013) across a broad range of commercial building types and all three climate zones in New York. In collaboration with New Building Institute, the EEMs were developed from national model codes and standards, high-performance building codes and standards, regional energy codes, and measures being proposed as part of the on-going code development process. PNNL analyzed these measures using whole building energy models for selected prototype commercial buildings and multifamily buildings representing buildings in New

INLUX-DBR - A calculation code to calculate indoor natural illuminance inside buildings under various sky conditions

Energy Technology Data Exchange (ETDEWEB)

Ferraro, V.; Igawa, N.; Marinelli, V. [Mechanical Engineering Department, University of Calabria, 87036 Arcavacata di Rende (CS) (Italy)

2010-09-15

A calculation code, named INLUX-DBR, is presented, which is a modified version of INLUX code, able to predict the illuminance distribution on the inside surfaces of a room with six walls and a window, and on the work plane. At each desired instant the code solves the system of the illuminance equations of each surface element, characterized by the latter's reflection coefficient and its view factors toward the other elements. In the model implemented in the code, the sky-diffuse luminance distribution, the sun beam light and the light reflected from the ground toward the room are considered. The code was validated by comparing the calculated values of illuminance with the experimental values measured inside a scale model (1:5) of a building room, in various sky conditions of overcast, clear and intermediate days. The validation is performed using the sky luminance data measured by a sky scanner and the measured beam illuminance of the sun as input data. A comparative analysis of some of the well-known calculation models of sky luminance, namely Perez, Igawa and CIE models was also carried out, comparing the code predictions and the measured values of inside illuminance in the scale model. (author)

Fire risk assessment method under the technical building code; Metodo de evaluacion del reisgo de incendio en el marco del Codigo Tecnico de la Edificacion

Energy Technology Data Exchange (ETDEWEB)

Perez-Martin, J. C.; Diaz-Diaz, R.; Santos-Garcia, R.

2010-07-01

The high complexity of measuring and comparing the risk level of performance based design allowed by the Spain Building Code (CTE) and the lack of Spanish legislation on the matter makes a fire risk evaluation tool highly useful guiding the project's and the control authority over the feasibility of these complicated projects. A fire Risk Evaluation Method within the frame of the Spanish Building Code (MEREDICTE) has been developed trying to balance input sources, simplicity and clearness in its use. The number of parameters implied guarantees sound, exhaustive and reliable outputs. MEREDICTE is made of 73 parameters: 31 calculate potential risk and 42 obtain protection level. In an orientative way, MEREDICTE's parameters triple those of the most referred and extended evaluation method: the Gretener Method. The article shows the MEREDICTE technique and foundations, the methodology used in its investigation and development, its most significant innovation and its possible applications. Regarding the protection level, its formulation and applications re referred to the Windsor buildings of Madrid comparing the results obtained on the building as it was devastated by the fire of February 2005 and whether it fulfilled the Spanish building code conditions. (Author) 8 refs.

Improving building energy efficiency in India: State-level analysis of building energy efficiency policies

Energy Technology Data Exchange (ETDEWEB)

Yu, Sha; Tan, Qing; Evans, Meredydd; Kyle, Page; Vu, Linh; Patel, Pralit L.

2017-11-01

India is expected to add 40 billion m2 of new buildings till 2050. Buildings are responsible for one third of India’s total energy consumption today and building energy use is expected to continue growing driven by rapid income and population growth. The implementation of the Energy Conservation Building Code (ECBC) is one of the measures to improve building energy efficiency. Using the Global Change Assessment Model, this study assesses growth in the buildings sector and impacts of building energy policies in Gujarat, which would help the state adopt ECBC and expand building energy efficiency programs. Without building energy policies, building energy use in Gujarat would grow by 15 times in commercial buildings and 4 times in urban residential buildings between 2010 and 2050. ECBC improves energy efficiency in commercial buildings and could reduce building electricity use in Gujarat by 20% in 2050, compared to the no policy scenario. Having energy codes for both commercial and residential buildings could result in additional 10% savings in electricity use. To achieve these intended savings, it is critical to build capacity and institution for robust code implementation.

Roadmap for the Future of Commercial Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, Michael I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hart, Philip R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhang, Jian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Athalye, Rahul A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-01-01

Building energy codes have significantly increased building efficiency over the last 38 years, since the first national energy code was published in 1975. The most commonly used path in energy codes, the prescriptive path, appears to be reaching a point of diminishing returns. The current focus on prescriptive codes has limitations including significant variation in actual energy performance depending on which prescriptive options are chosen, a lack of flexibility for designers and developers, the inability to handle optimization that is specific to building type and use, the inability to account for project-specific energy costs, and the lack of follow-through or accountability after a certificate of occupancy is granted. It is likely that an approach that considers the building as an integrated system will be necessary to achieve the next real gains in building efficiency. This report provides a high-level review of different formats for commercial building energy codes, including prescriptive, prescriptive packages, capacity constrained, outcome based, and predictive performance approaches. This report also explores a next generation commercial energy code approach that places a greater emphasis on performance-based criteria.

An Efficient Construction of Self-Dual Codes

OpenAIRE

Lee, Yoonjin; Kim, Jon-Lark

2012-01-01

We complete the building-up construction for self-dual codes by resolving the open cases over $GF(q)$ with $q \\equiv 3 \\pmod 4$, and over $\\Z_{p^m}$ and Galois rings $\\GR(p^m,r)$ with an odd prime $p$ satisfying $p \\equiv 3 \\pmod 4$ with $r$ odd. We also extend the building-up construction for self-dual codes to finite chain rings. Our building-up construction produces many new interesting self-dual codes. In particular, we construct 945 new extremal self-dual ternary $[32,16,9]$ codes, each ...

Preserving Envelope Efficiency in Performance Based Code Compliance

Energy Technology Data Exchange (ETDEWEB)

Thornton, Brian A. [Thornton Energy Consulting (United States); Sullivan, Greg P. [Efficiency Solutions (United States); Rosenberg, Michael I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Baechler, Michael C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-06-20

The City of Seattle 2012 Energy Code (Seattle 2014), one of the most progressive in the country, is under revision for its 2015 edition. Additionally, city personnel participate in the development of the next generation of the Washington State Energy Code and the International Energy Code. Seattle has pledged carbon neutrality by 2050 including buildings, transportation and other sectors. The United States Department of Energy (DOE), through Pacific Northwest National Laboratory (PNNL) provided technical assistance to Seattle in order to understand the implications of one potential direction for its code development, limiting trade-offs of long-lived building envelope components less stringent than the prescriptive code envelope requirements by using better-than-code but shorter-lived lighting and heating, ventilation, and air-conditioning (HVAC) components through the total building performance modeled energy compliance path. Weaker building envelopes can permanently limit building energy performance even as lighting and HVAC components are upgraded over time, because retrofitting the envelope is less likely and more expensive. Weaker building envelopes may also increase the required size, cost and complexity of HVAC systems and may adversely affect occupant comfort. This report presents the results of this technical assistance. The use of modeled energy code compliance to trade-off envelope components with shorter-lived building components is not unique to Seattle and the lessons and possible solutions described in this report have implications for other jurisdictions and energy codes.

PROCEDURES FOR SEISMIC CHARACTERIZATION OF TRADITIONAL AND MODERN WOODEN BUILDING TYPES

Directory of Open Access Journals (Sweden)

Ario Ceccotti

2016-03-01

Full Text Available The paper analyzes different wooden buildings types used in past and nowadays to realized low-rise and mid-rise timber structures from the seismic point of view. A preliminary overview about the procedures prescribed by codes for the seismic characterization of the timber building systems is given. Then the definition of the behaviour q-factor in the literature and its relevance in design of structures in seismic areas is treated. Available research methods for estimating the q-factor based on the verification of the nonlinear seismic response of entire buildings by means of experimental tests and numerical simulations are presented and analyzed. The relevance of a proper definition of the yielding limit and of failure condition in the seismic characterization of wooden building systems is treated. Moreover, a comparison between the q-factor estimations obtained using different calculation methods is presented. Lastly, the appropriate q-factor values are given for a reliable and safe seismic design of buildings realized using the examined wooden constructive systems.

Energy Code Enforcement Training Manual : Covering the Washington State Energy Code and the Ventilation and Indoor Air Quality Code.

Energy Technology Data Exchange (ETDEWEB)

Washington State Energy Code Program

1992-05-01

This manual is designed to provide building department personnel with specific inspection and plan review skills and information on provisions of the 1991 edition of the Washington State Energy Code (WSEC). It also provides information on provisions of the new stand-alone Ventilation and Indoor Air Quality (VIAQ) Code.The intent of the WSEC is to reduce the amount of energy used by requiring energy-efficient construction. Such conservation reduces energy requirements, and, as a result, reduces the use of finite resources, such as gas or oil. Lowering energy demand helps everyone by keeping electricity costs down. (It is less expensive to use existing electrical capacity efficiently than it is to develop new and additional capacity needed to heat or cool inefficient buildings.) The new VIAQ Code (effective July, 1991) is a natural companion to the energy code. Whether energy-efficient or not, an homes have potential indoor air quality problems. Studies have shown that indoor air is often more polluted than outdoor air. The VIAQ Code provides a means of exchanging stale air for fresh, without compromising energy savings, by setting standards for a controlled ventilation system. It also offers requirements meant to prevent indoor air pollution from building products or radon.

Modules in historic building construction according to the Copenhagen Building Code

DEFF Research Database (Denmark)

Kudsk, Anders; Thuesen, Christian Langhoff; Hvam, Lars

2011-01-01

This paper describes an analysis of building works from Copenhagen, Denmark in the period 1850 to 1950. In the study we investigate, based on the theory of product architecture and product modularization, if examples of the use of well-defined interfaces can be found. Furthermore, the aim...... is to study how the use of such interfaces has influenced former building processes and how they were implemented and kept stable over decades. The result of the study is that at that time a number of standardized interfaces between the individual parts of the building work existed, and that these interfaces...

Safe pill-dispensing.

Science.gov (United States)

Testa, Massimiliano; Pollard, John

2007-01-01

Each patient is supplied with a smart-card containing a Radio Frequency IDentification (RFID) chip storing a unique identification code. The patient places the Smart-card on a pill-dispenser unit containing an RFID reader. The RFID chip is read and the code sent to a Base-station via a wireless Bluetooth link. A database containing both patient details and treatment information is queried at the Base-station using the RFID as the search key. The patient's treatment data (i.e., drug names, quantities, time, etc.) are retrieved and sent back to the pill-dispenser unit via Bluetooth. Appropriate quantities of the required medications are automatically dispensed, unless the patient has already taken his/her daily dose. Safe, confidential communication and operation is ensured.

Coding for dummies

CERN Document Server

Abraham, Nikhil

2015-01-01

Hands-on exercises help you learn to code like a pro No coding experience is required for Coding For Dummies,your one-stop guide to building a foundation of knowledge inwriting computer code for web, application, and softwaredevelopment. It doesn't matter if you've dabbled in coding or neverwritten a line of code, this book guides you through the basics.Using foundational web development languages like HTML, CSS, andJavaScript, it explains in plain English how coding works and whyit's needed. Online exercises developed by Codecademy, a leading online codetraining site, help hone coding skill

Tornado Protection: Selecting and Designing Safe Areas in Buildings.

Science.gov (United States)

Abernethy, James J.

Tornadoes and extreme winds cause heavy loss of life and property damage throughout the United States. Most buildings offer significant protection from this danger, and building administrators should know the areas where this protection is available. This booklet presents a review of three schools, all of which were struck by tornadoes on April 3,…

Potential impacts of climate change on the built environment: ASHRAE climate zones, building codes and national energy efficiency

Energy Technology Data Exchange (ETDEWEB)

New, Joshua Ryan [ORNL; Kumar, Jitendra [ORNL; Hoffman, Forrest M. [ORNL

2017-10-01

Statement of the Problem: ASHRAE releases updates to 90.1 “Energy Standard for Buildings except Low-Rise Residential Buildings” every three years resulting in a 3.7%-17.3% increase in energy efficiency for buildings with each release. This is adopted by or informs building codes in nations across the globe, is the National Standard for the US, and individual states elect which release year of the standard they will enforce. These codes are built upon Standard 169 “Climatic Data for Building Design Standards,” the latest 2017 release of which defines climate zones based on 8, 118 weather stations throughout the world and data from the past 8-25 years. This data may not be indicative of the weather that new buildings built today, will see during their upcoming 30-120 year lifespan. Methodology & Theoretical Orientation: Using more modern, high-resolution datasets from climate satellites, IPCC climate models (PCM and HadGCM), high performance computing resources (Titan) and new capabilities for clustering and optimization the authors briefly analyzed different methods for redefining climate zones. Using bottom-up analysis of multiple meteorological variables which were the subject matter, experts selected as being important to energy consumption, rather than the heating/cooling degree days currently used. Findings: We analyzed the accuracy of redefined climate zones, compared to current climate zones and how the climate zones moved under different climate change scenarios, and quantified the accuracy of these methods on a local level, at a national scale for the US. Conclusion & Significance: There is likely to be a significant annual, national energy and cost (billions USD) savings that could be realized by adjusting climate zones to take into account anticipated trends or scenarios in regional weather patterns.

Net Zero Energy Buildings

DEFF Research Database (Denmark)

Marszal, Anna Joanna; Bourrelle, Julien S.; Gustavsen, Arild

2010-01-01

and identify possible renewable energy supply options which may be considered in calculations. Finally, the gap between the methodology proposed by each organisation and their respective national building code is assessed; providing an overview of the possible changes building codes will need to undergo......The international cooperation project IEA SHC Task 40 / ECBCS Annex 52 “Towards Net Zero Energy Solar Buildings”, attempts to develop a common understanding and to set up the basis for an international definition framework of Net Zero Energy Buildings (Net ZEBs). The understanding of such buildings...

Cryptography cracking codes

CERN Document Server

2014-01-01

While cracking a code might seem like something few of us would encounter in our daily lives, it is actually far more prevalent than we may realize. Anyone who has had personal information taken because of a hacked email account can understand the need for cryptography and the importance of encryption-essentially the need to code information to keep it safe. This detailed volume examines the logic and science behind various ciphers, their real world uses, how codes can be broken, and the use of technology in this oft-overlooked field.

Analysis of Potential Benefits and Costs of Adopting ASHRAE Standard 90.1-1999 as a Commercial Building Energy Code in Illinois Jurisdictions

Energy Technology Data Exchange (ETDEWEB)

Belzer, David B.; Cort, Katherine A.; Winiarski, David W.; Richman, Eric E.; Friedrich, Michele

2002-05-01

ASHRAE Standard 90.1-1999 was developed in an effort to set minimum requirements for energy efficienty design and construction of new commercial buildings. This report assesses the benefits and costs of adopting this standard as the building energy code in Illinois. Energy and economic impacts are estimated using BLAST combined with a Life-Cycle Cost approach to assess corresponding economic costs and benefits.

Dynamic Response of AP1000 Nuclear Island Due to Safe Shutdown Earthquake Loading

Directory of Open Access Journals (Sweden)

Gan Buntara S.

2017-01-01

Full Text Available AP1000 is a standard nuclear power plant developed by Westinghouse and its partners by using an advanced passive safety feature. Among the five principle building structures, namely the nuclear island, turbine building, annex building, diesel generator building and radwaste building, the safety of the nuclear island building is the most concerned. This paper investigates the dynamic response of the nuclear island building of the AP1000 plant subjected to safe shutdown earthquake loadings. A finite element model for the building, which is assumed to be built in a hard-rock base, is developed and its dynamic response is computed with the aid of the commercial finite element package ANSYS. The dynamic characteristics, including the natural frequencies, the vibration modes, and the time histories for displacements, velocities, and accelerations of the building are obtained for two typical safe shutdown earthquakes, El Centro and Kobe earthquakes. The dynamic behavior of the building due to the earthquakes and its safety is examined and highlighted.

Green Building Tools for Tribes

Science.gov (United States)

Tribal green building tools and funding information to support tribal building code adoption, healthy building, siting, energy efficiency, renewable energy, water conservation, green building materials, recycling and adaptation and resilience.

Assessment of the Fire Risk Levels in an Office Building and a Nightclub with Prescriptive Designs

DEFF Research Database (Denmark)

Yilmaz, D.; Steffensen, F.B.; Jomaas, Grunde

2014-01-01

A comparison of the risk level of an office building and a nightclub with code compliant prescriptive designs was conducted in order to evaluate whether an uniform safety level of the two occupancy types can be established. A risk assessment method using Monte Carlo simulations and 1- and 2-zone......-movement time and the movement time were adjusted for the required safe egress time (RSET) of the nightclub. The number of simulations required in order to obtain reliable results was considered sufficient at 20,000. The comparison of the risk profiles of the nightclub and the office building showed significant...... difference in risk levels, with that of the nightclub being substantially higher. The higher risk level in the nightclub is caused by a relatively fast mean value of the fire growth rate and the high number of occupants. Hence, the requirements in the prescriptive code do not ensure a similar safety level...

Tribal Green Building Toolkit

Science.gov (United States)

This Tribal Green Building Toolkit (Toolkit) is designed to help tribal officials, community members, planners, developers, and architects develop and adopt building codes to support green building practices. Anyone can use this toolkit!

Climate responsive and safe earthquake construction: a community building a school

Directory of Open Access Journals (Sweden)

Hari Darshan

2011-10-01

Full Text Available This article outlines environment friendly features, climate responsive features and construction features of a prototype school building constructed using green building technology. The school building has other additional features such as earthquake resistant construction, use of local materials and local technology. The construction process not only establishes community ownership, but also facilitates dissemination of the technology to the communities. Schools are effective media for raising awareness, disseminating technology and up-scaling the innovative approach. The approach is cost effective and sustainable for long-term application of green building technology. Furthermore, this paper emphasizes that such construction technology will be instrumental to build culture of safety in communities and reduce disaster risk.

Infinity-Norm Permutation Covering Codes from Cyclic Groups

OpenAIRE

Karni, Ronen; Schwartz, Moshe

2017-01-01

We study covering codes of permutations with the $\\ell_\\infty$-metric. We provide a general code construction, which uses smaller building-block codes. We study cyclic transitive groups as building blocks, determining their exact covering radius, and showing linear-time algorithms for finding a covering codeword. We also bound the covering radius of relabeled cyclic transitive groups under conjugation.

Feedback Codes and Action Plans: Building the Capacity of First-Year Students to Apply Feedback to a Scientific Report

Science.gov (United States)

Bird, Fiona L.; Yucel, Robyn

2015-01-01

Effective feedback can build self-assessment skills in students so that they become more competent and confident to identify and self-correct weaknesses in their work. In this study, we trialled a feedback code as part of an integrated programme of formative and summative assessment tasks, which provided feedback to first-year students on their…

Green Building Standards

Science.gov (United States)

Many organizations have developed model codes or rating systems that communities may use to develop green building programs or revise building ordinances. Some of the major options are listed on this page.

Ultra Safe And Secure Blasting System

Energy Technology Data Exchange (ETDEWEB)

Hart, M M

2009-07-27

The Ultra is a blasting system that is designed for special applications where the risk and consequences of unauthorized demolition or blasting are so great that the use of an extraordinarily safe and secure blasting system is justified. Such a blasting system would be connected and logically welded together through digital code-linking as part of the blasting system set-up and initialization process. The Ultra's security is so robust that it will defeat the people who designed and built the components in any attempt at unauthorized detonation. Anyone attempting to gain unauthorized control of the system by substituting components or tapping into communications lines will be thwarted in their inability to provide encrypted authentication. Authentication occurs through the use of codes that are generated by the system during initialization code-linking and the codes remain unknown to anyone, including the authorized operator. Once code-linked, a closed system has been created. The system requires all components connected as they were during initialization as well as a unique code entered by the operator for function and blasting.

Comparison of european computer codes relative to the aerosol behavior in PWR containment buildings during severe core damage accidents

International Nuclear Information System (INIS)

Fermandjian, J.; Beonio-Brocchieri, F.

1986-09-01

The present study concerns a comparative exercise, performed within the framework of the Commission of the European Communities, of the computer codes used in reactor safety in order to assess their capability of realistically describing the aerosol behavior in PWR reactor containment buildings during severe accidents. The codes included in the present study are the following: AEROSIM-M, AEROSOLS/Bl, CORRAL-2, NAUA Mod5. In AEROSIM-M, AEROSOLS/Bl and NAUA Mod5, the integro-differential equation for the evolution of the particle mass distribution is approximated by a set of coupled first order differential equations. To this end, the particle distribution function is replaced by a number of discrete monodisperse fractions. The CORRAL-2 has an essentially empirical basis (processes not explicitely modelled, but their net effects accounted for). The physical processes taken into account in the codes are shown finally

Confidence building on the total system performance assessment code, MASCOT-K for permanent disposal of HLW in Korea

Energy Technology Data Exchange (ETDEWEB)

Hwang, Y. S.; Kim, S. G.; Kang, C. H

2002-12-01

To perform Total System Performance Assessment(TSPA) of a potential HLW repository, it is necessary to develop the TSPA code. KAERI has developed the one-dimensional PSA code MASCOT-K since 1997 and verified special modules dedicated for the dissolution of spent nuclear fuel. In the second R and D phase, MASCOT-K is once again verified as a part of the confidence building for TSPA. The AMBER code based on the totally different mathematical approach, compartment theory is used together with MASCOT-K to assess the annual individual doses for given K- and Q- scenarios. Results indicate that both AMBER and MASCOT-K simulate the annual individual doses to a potential biosphere. And the MASCOT-K is more flexible to describe the natural barrier such as a fracture for sensitivity studies. In the third R and D phase, MASCOT-K will be actively used to check whether the proposed KAERI reference disposal concept is solid or not.

Confidence building on the total system performance assessment code, MASCOT-K for permanent disposal of HLW in Korea

International Nuclear Information System (INIS)

Hwang, Y. S.; Kim, S. G.; Kang, C. H.

2002-12-01

To perform Total System Performance Assessment(TSPA) of a potential HLW repository, it is necessary to develop the TSPA code. KAERI has developed the one-dimensional PSA code MASCOT-K since 1997 and verified special modules dedicated for the dissolution of spent nuclear fuel. In the second R and D phase, MASCOT-K is once again verified as a part of the confidence building for TSPA. The AMBER code based on the totally different mathematical approach, compartment theory is used together with MASCOT-K to assess the annual individual doses for given K- and Q- scenarios. Results indicate that both AMBER and MASCOT-K simulate the annual individual doses to a potential biosphere. And the MASCOT-K is more flexible to describe the natural barrier such as a fracture for sensitivity studies. In the third R and D phase, MASCOT-K will be actively used to check whether the proposed KAERI reference disposal concept is solid or not

Comparison of computer codes relative to the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Bunz, H.; Dunbar, I.; Gauvain, J.; Ricchena, R.

1986-01-01

The present study concerns a comparative exercise, performed within the framework of the Commission of the European Communities, of the computer codes (AEROSIM-M, UK; AEROSOLS/B1, France; CORRAL-2, CEC and NAUA Mod5, Germany) used in order to assess the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR. Topics considered in this paper include aerosols, containment buildings, reactor safety, fission product release, reactor cores, meltdown, and monitoring

Performance of Buildings in the 2009 Western Sumatra Earthquake

Science.gov (United States)

Deierlein, G.; Hart, T.; Alexander, N.; Hausler, E.; Henderson, S.; Wood, K.; Cedillos, V.; Wijanto, S.; Cabrera, C.; Rudianto, S.

2009-12-01

The M7.6 earthquake of 30 September 2009 in Western Sumatra, Indonesia caused significant damage and collapse to hundreds of buildings and the deaths of 1,117 people. In Padang City, with a population of about 900,000 people, building collapse was the primary cause of deaths and serious injuries (313 deaths and 431 serious injuries). The predominant building construction types in Padang are concrete moment frames with brick infill and masonry bearing wall systems. Concrete frames are common in multistory commercial retail buildings, offices, schools, and hotels; and masonry bearing wall systems are primarily used in low-rise (usually single story) residential and school buildings. In general, buildings that collapsed did not conform to modern seismic engineering practices that are required by the current Indonesian building code and would be expected in regions of moderate to high seismicity. While collapse of multi-story concrete buildings was more prevalent in older buildings (more than 10 years old), there were several newer buildings that collapsed. Primary deficiencies identified in collapsed or severely damaged buildings included: (a) soft or weak stories that failed in either by sidesway mechanisms or shear failures followed by loss of axial capacity of columns, (b) lack of ductile reinforcing bar detailing in concrete beams, columns, and beam-column joints, (c) poor quality concrete and mortar materials and workmanship, (d) vulnerable building configurations and designs with incomplete or deficient load paths, and (e) out-of-plane wall failures in unreinforced (or marginally reinforced) masonry. While these deficiencies may be expected in older buildings, damage and collapse to some modern (or recently rennovated buildings) indicates a lack of enforcement of building code provisions for design and construction quality assurance. Many new buildings whose structural systems were undamaged were closed due to extensive earthquake damage to brick infill walls

Design and operation of ventilation in low energy residences – A survey on code requirements and building reality from six European countries and China

DEFF Research Database (Denmark)

del Carmen Bocanegra-Yanez, Maria; Rojas, Gabriel; Zukowska-Tejsen, Daria

involved in the Annex. There were two main objectives, firstly, to describe and analyse a transition between actual requirements (national building codes and standards) and current practice. Secondly, to investigate current barriers and challenges regarding installation of mechanical ventilation......One of the key objectives of the IEA Annex 68 research programme entitled “Indoor Air Quality Design and Control in Low Energy Residential Buildings” is to provide a generic guideline for the design and operation of ventilation in residential buildings. Modern and refurnished domestic buildings...

New Site Coefficients and Site Classification System Used in Recent Building Seismic Code Provisions

Science.gov (United States)

Dobry, R.; Borcherdt, R.D.; Crouse, C.B.; Idriss, I.M.; Joyner, W.B.; Martin, G.R.; Power, M.S.; Rinne, E.E.; Seed, R.B.

2000-01-01

Recent code provisions for buildings and other structures (1994 and 1997 NEHRP Provisions, 1997 UBC) have adopted new site amplification factors and a new procedure for site classification. Two amplitude-dependent site amplification factors are specified: Fa for short periods and Fv for longer periods. Previous codes included only a long period factor S and did not provide for a short period amplification factor. The new site classification system is based on definitions of five site classes in terms of a representative average shear wave velocity to a depth of 30 m (V?? s). This definition permits sites to be classified unambiguously. When the shear wave velocity is not available, other soil properties such as standard penetration resistance or undrained shear strength can be used. The new site classes denoted by letters A - E, replace site classes in previous codes denoted by S1 - S4. Site classes A and B correspond to hard rock and rock, Site Class C corresponds to soft rock and very stiff / very dense soil, and Site Classes D and E correspond to stiff soil and soft soil. A sixth site class, F, is defined for soils requiring site-specific evaluations. Both Fa and Fv are functions of the site class, and also of the level of seismic hazard on rock, defined by parameters such as Aa and Av (1994 NEHRP Provisions), Ss and S1 (1997 NEHRP Provisions) or Z (1997 UBC). The values of Fa and Fv decrease as the seismic hazard on rock increases due to soil nonlinearity. The greatest impact of the new factors Fa and Fv as compared with the old S factors occurs in areas of low-to-medium seismic hazard. This paper summarizes the new site provisions, explains the basis for them, and discusses ongoing studies of site amplification in recent earthquakes that may influence future code developments.

InaSAFE applications in disaster preparedness

Science.gov (United States)

Pranantyo, Ignatius Ryan; Fadmastuti, Mahardika; Chandra, Fredy

2015-04-01

Disaster preparedness activities aim to reduce the impact of disasters by being better prepared to respond when a disaster occurs. In order to better anticipate requirements during a disaster, contingency planning activities can be undertaken prior to a disaster based on a realistic disaster scenario. InaSAFE is a tool that can inform this process. InaSAFE is a free and open source software that estimates the impact to people and infrastructure from potential hazard scenarios. By using InaSAFE, disaster managers can develop scenarios of disaster impacts (people and infrastructures affected) to inform their contingency plan and emergency response operation plan. While InaSAFE provides the software framework exposure data and hazard data are needed as inputs to run this software. Then InaSAFE can be used to forecast the impact of the hazard scenario to the exposure data. InaSAFE outputs include estimates of the number of people, buildings and roads are affected, list of minimum needs (rice and clean water), and response checklist. InaSAFE is developed by Indonesia's National Disaster Management Agency (BNPB) and the Australian Government, through the Australia-Indonesia Facility for Disaster Reduction (AIFDR), in partnership with the World Bank - Global Facility for Disaster Reduction and Recovery (GFDRR). This software has been used in many parts of Indonesia, including Padang, Maumere, Jakarta, and Slamet Mountain for emergency response and contingency planning.

Energy - efficient buildings in pakistan

International Nuclear Information System (INIS)

Sohail, M.; Qureshi, M.U.D.

2011-01-01

Pakistan is one of the countries with the highest energy consumption for domestic use. Annual energy consumption by the domestic sector is 45.9 % of the total, while the industrial sector, consumes about 27.5%. About half of the total energy consumed is used in buildings and/or heating, ventilation and air-conditioning (HVAC) and lighting appliances. The energy consumed for the same purposes in China and UK is 25 to 30 % and 40 %, respectively, even in extreme weather conditions. Energy deficiency in Pakistan is approximately 5,000 MWe, which results in worst load-shedding in summers and, lately, even in winters. Building new energy sources like dams, coal power plants and renewable energy power projects are some possible solutions, but these are time taking and need at least 2 to 6 years to complete, depending upon the nature of the project. Fast development of energy-efficient buildings is, therefore, necessary to deal with exacerbating energy-crisis and related environmental impact in Pakistan. Innovations in the prevailing building-design will help the country in reducing the energy burden. These innovations may include improved architectural designs, energy-efficient building materials, electrical appliances and implementation of building energy-efficiency codes. In 1987, the National Energy Conservation Centre (ENERCON), was established under Ministry of Environment, Government of Pakistan, with the aim to build awareness among the masses for energy conservation, and to make policies regarding energy-conservation structures in the country. But no policy regarding building energy codes has been introduced by ENERCON till now. In collaboration with Pakistan Engineering Council (PEC), ENERCON has recently finalized the Building Energy Code of Pakistan Energy Provisions 2011 for which statutory notification is under process for necessary amendment in the building by-laws. The implementation of this Energy Code will result in 25 to 30 % of energy savings in the

Seismic performance of existing R.C. framed buildings

Directory of Open Access Journals (Sweden)

Sameh A. El-Betar

2017-08-01

Full Text Available The earthquakes disasters basically occur due to buildings damage not because of the earth shaking. Therefore, the countries have being updated the seismic codes. The seismic loads for buildings design in Egyptian Code have been changed from (EC-1994 to (ECP-201, 2012. On the other hand, the need is raised to study the vulnerability of existing buildings, which can be divided into the buildings designed to resist the gravity loads only (GLD and the buildings designed according to Egyptian code (EC-1994. Comparison between forces due to Egyptian code for loads (EC-1994 and (ECP-201, 2012 is carried out on the multi-stories R.C. framed buildings which are the most common type of existing buildings in Egypt. To investigate the vulnerability of existing buildings, nonlinear static pushover analysis is conducted to evaluate the real strength of the existing buildings. Moreover, it is considered a useful and effective tool for the performance of three framed buildings: 3, 6 and 10 stories due to expected future earthquakes. Finally, it is found that the vulnerability of existing GLD buildings occurs at expected ground accelerations (ag greater than 0.125 g in Egyptian seismic map, while the EC-94 designed buildings behave elastically up to (ag equals to 0.2 g and above that a slight damage may occur.

Codes and Standards Technical Team Roadmap

Energy Technology Data Exchange (ETDEWEB)

None

2013-06-01

The Hydrogen Codes and Standards Tech Team (CSTT) mission is to enable and facilitate the appropriate research, development, & demonstration (RD&D) for the development of safe, performance-based defensible technical codes and standards that support the technology readiness and are appropriate for widespread consumer use of fuel cells and hydrogen-based technologies with commercialization by 2020. Therefore, it is important that the necessary codes and standards be in place no later than 2015.

Thermal Comfort and Ventilation Criteria for low Energy Residential Buildings in Building Codes

DEFF Research Database (Denmark)

Cao, Guangyu; Kurnitski, Jarek; Awbi, Hazim

2012-01-01

of the indoor air quality in such buildings. Currently, there are no global guidelines for specifying the indoor thermal environment in such low-energy buildings. The objective of this paper is to analyse the classification of indoor thermal comfort levels and recommended ventilation rates for different low...

Risk assessments and safe machinery ensuring compliance with the EU directives

CERN Document Server

Jespen, Torben

2016-01-01

This book describes the prerequisites for the placing on the market and the safe use of machinery in compliance with the relevant EU Directives, especially the Machinery Directive 2006/42. It provides readers with high-level knowledge concerning the Essential Health and Safety Requirements (EHSR) that machinery must fulfill. The approach and principles of the Machinery Directive were most recently made worldwide acknowledged in the ILO code of practice on safe machinery, released in 2013. The book addresses that code, as well as providing valuable insight into other EU Product and Workplace legislation. Focusing on the key aspect of safe machinery, the “machinery safety risk assessment”, which allows readers to better understand the more difficult aspects of risk assessments, the book equips readers to tackle problems at the manufacturing stage and in different use scenarios, introducing them to risk reduction techniques and functional safety aspects.

OM Code Requirements For MOVs -- OMN-1 and Appendix III

Energy Technology Data Exchange (ETDEWEB)

Kevin G. DeWall

2011-08-01

The purpose or scope of the ASME OM Code is to establish the requirements for pre-service and in-service testing of nuclear power plant components to assess their operational readiness. For MOVs this includes those that perform a specific function in shutting down a reactor to the safe shutdown condition, maintaining the safe shutdown condition, and mitigating the consequences of an accident. This paper will present a brief history of industry and regulatory activities related to MOVs and the development of Code requirements to address weaknesses in earlier versions of the OM Code. The paper will discuss the MOV requirements contained in the 2009 version of ASME OM Code, specifically Mandatory Appendix III and OMN-1, Revision 1.

OM Code Requirements For MOVs -- OMN-1 and Appendix III

International Nuclear Information System (INIS)

DeWall, Kevin G.

2011-01-01

The purpose or scope of the ASME OM Code is to establish the requirements for pre-service and in-service testing of nuclear power plant components to assess their operational readiness. For MOVs this includes those that perform a specific function in shutting down a reactor to the safe shutdown condition, maintaining the safe shutdown condition, and mitigating the consequences of an accident. This paper will present a brief history of industry and regulatory activities related to MOVs and the development of Code requirements to address weaknesses in earlier versions of the OM Code. The paper will discuss the MOV requirements contained in the 2009 version of ASME OM Code, specifically Mandatory Appendix III and OMN-1, Revision 1.

Coding for Electronic Mail

Science.gov (United States)

Rice, R. F.; Lee, J. J.

1986-01-01

Scheme for coding facsimile messages promises to reduce data transmission requirements to one-tenth current level. Coding scheme paves way for true electronic mail in which handwritten, typed, or printed messages or diagrams sent virtually instantaneously - between buildings or between continents. Scheme, called Universal System for Efficient Electronic Mail (USEEM), uses unsupervised character recognition and adaptive noiseless coding of text. Image quality of resulting delivered messages improved over messages transmitted by conventional coding. Coding scheme compatible with direct-entry electronic mail as well as facsimile reproduction. Text transmitted in this scheme automatically translated to word-processor form.

HBT+: an improved code for finding subhaloes and building merger trees in cosmological simulations

Science.gov (United States)

Han, Jiaxin; Cole, Shaun; Frenk, Carlos S.; Benitez-Llambay, Alejandro; Helly, John

2018-02-01

Dark matter subhalos are the remnants of (incomplete) halo mergers. Identifying them and establishing their evolutionary links in the form of merger trees is one of the most important applications of cosmological simulations. The HBT (Hierachical Bound-Tracing) code identifies haloes as they form and tracks their evolution as they merge, simultaneously detecting subhaloes and building their merger trees. Here we present a new implementation of this approach, HBT+ , that is much faster, more user friendly, and more physically complete than the original code. Applying HBT+ to cosmological simulations, we show that both the subhalo mass function and the peak-mass function are well fitted by similar double-Schechter functions. The ratio between the two is highest at the high-mass end, reflecting the resilience of massive subhaloes that experience substantial dynamical friction but limited tidal stripping. The radial distribution of the most-massive subhaloes is more concentrated than the universal radial distribution of lower mass subhaloes. Subhalo finders that work in configuration space tend to underestimate the masses of massive subhaloes, an effect that is stronger in the host centre. This may explain, at least in part, the excess of massive subhaloes in galaxy cluster centres inferred from recent lensing observations. We demonstrate that the peak-mass function is a powerful diagnostic of merger tree defects, and the merger trees constructed using HBT+ do not suffer from the missing or switched links that tend to afflict merger trees constructed from more conventional halo finders. We make the HBT+ code publicly available.

The fundamentals of structural building codes

NARCIS (Netherlands)

Vrouwenvelder, A.C.W.M.

2001-01-01

Partial Factor Design is nowadays a generally accepted design method for building and civil engineering structures. For most engineers the general philosophy that the safety factors depend on the type of the load and on the limit state under consideration makes sense. However, the background, in

77 FR 76434 - Solicitation of New Safe Harbors and Special Fraud Alerts

Science.gov (United States)

2012-12-28

... statute (section 1128B(b) of the Social Security Act), as well as developing new OIG Special Fraud Alerts... of New Safe Harbors and Special Fraud Alerts AGENCY: Office of Inspector General (OIG), HHS. ACTION... revised safe harbors and Special Fraud Alerts. Please assist us by referencing the file code OIG-121-N...

78 FR 78807 - Solicitation of New Safe Harbors and Special Fraud Alerts

Science.gov (United States)

2013-12-27

... statute (section 1128B(b) of the Social Security Act), as well as developing new OIG Special Fraud Alerts... of New Safe Harbors and Special Fraud Alerts AGENCY: Office of Inspector General (OIG), HHS. ACTION... revised safe harbors and Special Fraud Alerts. Please assist us by referencing the file code OIG-122-N...

Code of safe practice for the use of x-rays in podiatry

International Nuclear Information System (INIS)

1990-02-01

The purpose of this code which applies to podiatric diagnostic use of x-rays is to provide criteria for working procedures, x-ray equipment and protective materials necessary for the use of x-rays in podiatric diagnosis according to currently accepted standards of safety. Conformity with this code may be taken as a primary indication of compliance with radiation protection legislation. 5 refs

Building a dynamic code to simulate new reactor concepts

International Nuclear Information System (INIS)

Catsaros, N.; Gaveau, B.; Jaekel, M.-T.; Maillard, J.; Maurel, G.; Savva, P.; Silva, J.; Varvayanni, M.

2012-01-01

Highlights: ► We develop a stochastic neutronic code based on an existing High Energy Physics code. ► The code simulates innovative reactor designs including Accelerator Driven Systems. ► Core materials evolution will be dynamically simulated, including fuel burnup. ► Continuous feedback between the main inter-related parameters will be established. ► A description of the current research development and achievements is also given. - Abstract: Innovative nuclear reactor designs have been proposed, such as the Accelerator Driven Systems (ADSs), the “candle” reactors, etc. These reactor designs introduce computational nuclear technology problems the solution of which necessitates a new, global and dynamic computational approach of the system. A continuous feedback procedure must be established between the main inter-related parameters of the system such as the chemical, physical and isotopic composition of the core, the neutron flux distribution and the temperature field. Furthermore, as far as ADSs are concerned, the ability of the computational tool to simulate the nuclear cascade created from the interaction of accelerated protons with the spallation target as well as the produced neutrons, is also required. The new Monte Carlo code ANET (Advanced Neutronics with Evolution and Thermal hydraulic feedback) is being developed based on the GEANT3 High Energy Physics code, aiming to progressively satisfy all the above requirements. A description of the capabilities and methodologies implemented in the present version of ANET is given here, together with some illustrative applications of the code.

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can....... That has left the industry in constant pursuit of possibilities for integration of the tool within the Building Information Modelling environment so that the potential provided by the latter can be harvested and the processed can be optimized. This paper presents a solution for automated data extraction...... from building geometry created in Autodesk Revit and its translation to input for compliance check analysis....

The safe home project.

Science.gov (United States)

Arphorn, Sara; Jiraniratisai, Sopaphan; Rungtakul, Rungsri; Phutta, Nikom

2011-12-01

The Thai Health Promotion Foundation supported the Improvement of Quality of Life of Informal Workers project in Ban Luang District, Amphur Photaram, Ratchaburi Province. There were many informal workers in Ban Luang District. Sweet-crispy fish producers in Ban Luang were the largest group among the sweet-crispy fish producers in Thailand. This project was aimed at improving living and working conditions of informal workers, with a focus on the sweet-crispy fish group. Good practices of improved living and working conditions were used to help informal workers build safe, healthy and productive work environments. These informal workers often worked in substandard conditions and were exposed to various hazards in the working area. These hazards included risk of exposure to hot work environment, ergonomics-related injuries, chemical hazards, electrical hazards etc. Ergonomics problems were commonly in the sweet-crispy fish group. Unnatural postures such as prolonged sitting were performed dominantly. One hundred and fifty informal workers participated in this project. Occupational health volunteers were selected to encourage occupational health and safety in four groups of informal workers in 2009. The occupational health volunteers trained in 2008 were farmers, beauty salon workers and doll makers. The occupational health and safety knowledge is extended to a new informal worker group: sweet-crispy fish producer, in 2009. The occupational health and safety training for sweet-crispy fish group is conducted by occupational health volunteers. The occupational health volunteers increased their skills and knowledge assist in to make safe home and safe community through participatory oriented training. The improvement of living and working condition is conducted by using a modified WISH, Work Improvement for Safe Home, checklist. The plans of improvement were recorded. The informal workers showed improvement mostly on material handling and storage. The safe uses and safe

Prediction of hydrogen distribution in the reactor building in CANDU6 plant

International Nuclear Information System (INIS)

Jin, Y.; Song, Y.

2008-01-01

The CANDU plants have a lot of zircaloy. The fuel cladding, calandria tubes and pressure tubes are made of zircaloy. The zircaloy can be oxidized and hydrogen is generated during severe accident progression. The detonation or deflagration to detonation transition (DDT) due to hydrogen combustion may occur if the local hydrogen concentration or global hydrogen concentration exceeds certain value. The detonation may result in the rupture of the reactor building. The inside of the reactor building of CANDU plants is complex. So prediction of hydrogen distribution in the reactor building is important. This prediction is made using ISAAC code and GOTHIC code. ISAAC code partitioned the reactor building in to 7 compartments. GOTHIC code modeled the CANDU6 reactor building using 12 nodes. The hydrogen concentrations in the various compartments in the reactor building are compared. GOTHIC code slightly underpredicts hydrogen concentration in the F/M rooms than ISAAC code, but trend is same. The hydrogen concentration in the boiler room and the moderator room shows almost same as for both codes. (author)

Final Report. An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group

Energy Technology Data Exchange (ETDEWEB)

Rosenthal, Andrew [New Mexico State Univ., Las Cruces, NM (United States)

2013-12-30

The DOE grant, “An Integrated Partnership to Create and Lead the Solar Codes and Standards Working Group,” to New Mexico State University created the Solar America Board for Codes and Standards (Solar ABCs). From 2007 – 2013 with funding from this grant, Solar ABCs identified current issues, established a dialogue among key stakeholders, and catalyzed appropriate activities to support the development of codes and standards that facilitated the installation of high quality, safe photovoltaic systems. Solar ABCs brought the following resources to the PV stakeholder community; Formal coordination in the planning or revision of interrelated codes and standards removing “stove pipes” that have only roofing experts working on roofing codes, PV experts on PV codes, fire enforcement experts working on fire codes, etc.; A conduit through which all interested stakeholders were able to see the steps being taken in the development or modification of codes and standards and participate directly in the processes; A central clearing house for new documents, standards, proposed standards, analytical studies, and recommendations of best practices available to the PV community; A forum of experts that invites and welcomes all interested parties into the process of performing studies, evaluating results, and building consensus on standards and code-related topics that affect all aspects of the market; and A biennial gap analysis to formally survey the PV community to identify needs that are unmet and inhibiting the market and necessary technical developments.

A proposed framework for computational fluid dynamics code calibration/validation

International Nuclear Information System (INIS)

Oberkampf, W.L.

1993-01-01

The paper reviews the terminology and methodology that have been introduced during the last several years for building confidence n the predictions from Computational Fluid Dynamics (CID) codes. Code validation terminology developed for nuclear reactor analyses and aerospace applications is reviewed and evaluated. Currently used terminology such as ''calibrated code,'' ''validated code,'' and a ''validation experiment'' is discussed along with the shortcomings and criticisms of these terms. A new framework is proposed for building confidence in CFD code predictions that overcomes some of the difficulties of past procedures and delineates the causes of uncertainty in CFD predictions. Building on previous work, new definitions of code verification and calibration are proposed. These definitions provide more specific requirements for the knowledge level of the flow physics involved and the solution accuracy of the given partial differential equations. As part of the proposed framework, categories are also proposed for flow physics research, flow modeling research, and the application of numerical predictions. The contributions of physical experiments, analytical solutions, and other numerical solutions are discussed, showing that each should be designed to achieve a distinctively separate purpose in building confidence in accuracy of CFD predictions. A number of examples are given for each approach to suggest methods for obtaining the highest value for CFD code quality assurance

Enhancement of seismic resistance of buildings

Directory of Open Access Journals (Sweden)

Claudiu-Sorin Dragomir

2014-03-01

Full Text Available The objectives of the paper are both seismic instrumentation for damage assessment and enhancing of seismic resistance of buildings. In according with seismic design codes in force the buildings are designed to resist at seismic actions. Due to the time evolution of these design provisions, there are buildings that were designed decades ago, under the less stringent provisions. The conceptual conformation is nowadays provided in all Codes of seismic design. According to the Code of seismic design P100-1:2006 the asymmetric structures do not have an appropriate seismic configuration; they have disadvantageous distribution of volumes, mass and stiffness. Using results of temporary seismic instrumentation the safety condition of the building may be assessed in different phases of work. Based on this method, the strengthening solutions may be identified and the need of seismic joints may be emphasised. All the aforementioned ideas are illustrated through a case study. Therefore it will be analysed the dynamic parameter evolution of an educational building obtained in different periods. Also, structural intervention scenarios to enhance seismic resistance will be presented.

Coding Bootcamps : Building Future-Proof Skills through Rapid Skills Training

OpenAIRE

World Bank

2017-01-01

This report studies coding bootcamps. A new kind of rapid skills training program for the digital age. Coding bootcamps are typically short-term (three to six months), intensive and applied training courses provided by a third party that crowdsources the demand for low-skills tech talent. Coding bootcamps aim at low-entry level tech employability (for example, junior developer), providing a ...

Training program for energy conservation in new-building construction. Volume II. Energy conservation technology: for the building inspector

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

A Model Code for Energy Conservation in New Building Construction has been developed by those national organizations primarily concerned with the development and promulgation of model codes. The technical provisions are based on ASHRAE Standard 90-75 and are intended for use by state and local officials. This training manual contains the basic information necessary to acquaint the field building inspector with the concepts of energy conservation in buildings and instructs him in the basic techniques of field inspection of energy compliance.

A Guide to Building Commissioning

Energy Technology Data Exchange (ETDEWEB)

Baechler, Michael C.

2011-09-01

Commissioning is the process of verifying that a building's heating, ventilation, and air conditioning (HVAC) and lighting systems perform correctly and efficiently. Without commissioning, system and equipment problems can result in higher than necessary utility bills and unexpected and costly equipment repairs. This report reviews the benefits of commissioning, why it is a requirement for Leadership in Energy and Environmental Design (LEED) certification, and why building codes are gradually adopting commissioning activities into code.

Analysis of the Earthquake-Resistant Design Approach for Buildings in Mexico

Directory of Open Access Journals (Sweden)

Carrillo Julián

2014-01-01

Full Text Available The development of new codes for earthquake-resistant structures has made possible to guarantee a better performance of buildings, when they are subjected to seismic actions. Therefore, it is convenient that current codes for design of building become conceptually transparent when defining the strength modification factors and assessing maximum lateral displacements, so that the design process can be clearly understood by structural engineers. The aim of this study is to analyze the transparency of earthquake-resistant design approach for buildings in Mexico by means of a critical review of the factors for strength modification and displacement amplification. The approach of building design codes in US is also analyzed. It is concluded that earthquake-resistant design in Mexico have evolved in refinement and complexity. It is also demonstrated that the procedure prescribed by such design codes allows the assessment of the design strengths and displacements in a more rational way, in accordance not only with the present stage of knowledge but also with the contemporary tendencies in building codes. In contrast, the procedures used in US codes may not provide a clear view for seismic response assessment of buildings.

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can b...

Learning from Abruzzo earthquake buildings behaviour seen from the Building According-to-the-book perspectives

International Nuclear Information System (INIS)

Bazurro, P.; Benedettini, F.; Clemente, P.; Salvatori, A.

2009-01-01

A brief description, with the related photographs, is reported on the effects of the recent Abruzzo earthquake on buildings, particularly reinforced-concrete and masonry buildings. Following an overview of the technical building codes particularly focused on the area of L'Aquila, mention is made of cultural heritage structures. [it

Automating RPM Creation from a Source Code Repository

Science.gov (United States)

2012-02-01

apps/usr --with- libpq=/apps/ postgres make rm -rf $RPM_BUILD_ROOT umask 0077 mkdir -p $RPM_BUILD_ROOT/usr/local/bin mkdir -p $RPM_BUILD_ROOT...from a source code repository. %pre %prep %setup %build ./autogen.sh ; ./configure --with-db=/apps/db --with-libpq=/apps/ postgres make

International codes concerning the security of radioisotopes

International Nuclear Information System (INIS)

Kusama, Keiji

2013-01-01

Explained is the title subject with international and Japanese official argument or publications and actions, where the security is defined as protection of sealed and unsealed radioisotopes (RI) from malicious acts. IAEA worked out the Code of Conduct on the Safety and Security of Radioactive Sources in 2004 based on its preceding argument and with the turning point of the terrorism 3.11 (2001), and Nuclear Security Recommendations on radioactive material and associated facilities (2011), for whose prerequisite, Security of radioactive sources: implementing guide (2009) and Security in the transport of radioactive material (2008) had been drawn up. The Code of Conduct indicates the security system to regulate the sealed sources that each nation has to build up through legislation, setup of regulatory agency, registration of the sources, provision of concerned facilities with radiation protection, etc. For attaining this purpose, IAEA defined Guidance on the Import and Export of Radioactive Sources (2005, 2012), Categorization of radioactive sources (2005) and Dangerous quantities of radioactive material (D-VALUES) (2006). For updating the related matters, IAEA holds international conferences somewhere in the world every year. The Nuclear Security Recommendations indicate the nation's responsibility of building up and maintaining the security system above with well-balanced measures between the safe and secure use of RI without the invalid inhibition of their usage. Japan government worked out the concept essential for ensuring the nuclear security in Sep. 2011, in which for RI, defined were the risk and benefit in use and security, and securing role of the present legal systems concerning the safety handling and objective RI involved in their registration system. Securing measures of RI in such usage as medical and industrial aids must be of advanced usefulness and safety in harmony with activities of other countries. (T.T)

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

Documentation of compliance with the energy performance regulations at the end of the detailed design phase is mandatory for building owners in Denmark. Therefore, besides multidisciplinary input, the building design process requires various iterative analyses, so that the optimal solutions can...... be identified amongst multiple alternatives. However, meeting performance criteria is often associated with manual data inputs and retroactive modifications of the design. Due to poor interoperability between the authoring tools and the compliance check program, the processes are redundant and inefficient...... from building geometry created in Autodesk Revit and its translation to input for compliance check analysis....

Development of application program and building database to increase facilities for using the radiation effect assessment computer codes

International Nuclear Information System (INIS)

Hyun Seok Ko; Young Min Kim; Suk-Hoon Kim; Dong Hoon Shin; Chang-Sun Kang

2005-01-01

The current radiation effect assessment system is required the skillful technique about the application for various code and high level of special knowledge classified by field. Therefore, as a matter of fact, it is very difficult for the radiation users' who don't have enough special knowledge to assess or recognize the radiation effect properly. For this, we already have developed the five Computer codes(windows-based), that is the radiation effect assessment system, in radiation utilizing field including the nuclear power generation. It needs the computer program that non-specialist can use the five computer codes to have already developed with ease. So, we embodied the A.I-based specialist system that can infer the assessment system by itself, according to the characteristic of given problem. The specialist program can guide users, search data, inquire of administrator directly. Conceptually, with circumstance which user to apply the five computer code may encounter actually, we embodied to consider aspects as follows. First, the accessibility of concept and data to need must be improved. Second, the acquirement of reference theory and use of corresponding computer code must be easy. Third, Q and A function needed for solution of user's question out of consideration previously. Finally, the database must be renewed continuously. Actually, to express this necessity, we develop the client program to organize reference data, to build the access methodology(query) about organized data, to load the visible expression function of searched data. And It is embodied the instruction method(effective theory acquirement procedure and methodology) to acquire the theory referring the five computer codes. It is developed the data structure access program(DBMS) to renew continuously data with ease. For Q and A function, it is embodied the Q and A board within client program because the user of client program can search the content of question and answer. (authors)

Comparison of computer codes relative to the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR

International Nuclear Information System (INIS)

Fermandjian, J.; Dunbar, I.; Gauvain, J.; Ricchena, R.

1986-02-01

The present study concerns a comparative exercise, performed within the framework of the Commission of the European Communities, of the computer codes (AEROSISM-M, UK; AEROSOLS/BI, France; CORRAL-2, CEC and NAUA Mod5, Germany) used in order to assess the aerosol behavior in the reactor containment building during severe core damage accidents in a PWR

32 CFR 634.24 - Traffic planning and codes.

Science.gov (United States)

2010-07-01

... 32 National Defense 4 2010-07-01 2010-07-01 true Traffic planning and codes. 634.24 Section 634.24 National Defense Department of Defense (Continued) DEPARTMENT OF THE ARMY (CONTINUED) LAW ENFORCEMENT AND CRIMINAL INVESTIGATIONS MOTOR VEHICLE TRAFFIC SUPERVISION Traffic Supervision § 634.24 Traffic planning and codes. (a) Safe and efficient...

Coded Splitting Tree Protocols

DEFF Research Database (Denmark)

Sørensen, Jesper Hemming; Stefanovic, Cedomir; Popovski, Petar

2013-01-01

This paper presents a novel approach to multiple access control called coded splitting tree protocol. The approach builds on the known tree splitting protocols, code structure and successive interference cancellation (SIC). Several instances of the tree splitting protocol are initiated, each...... instance is terminated prematurely and subsequently iterated. The combined set of leaves from all the tree instances can then be viewed as a graph code, which is decodable using belief propagation. The main design problem is determining the order of splitting, which enables successful decoding as early...

pix2code: Generating Code from a Graphical User Interface Screenshot

OpenAIRE

Beltramelli, Tony

2017-01-01

Transforming a graphical user interface screenshot created by a designer into computer code is a typical task conducted by a developer in order to build customized software, websites, and mobile applications. In this paper, we show that deep learning methods can be leveraged to train a model end-to-end to automatically generate code from a single input image with over 77% of accuracy for three different platforms (i.e. iOS, Android and web-based technologies).

Steady-state and accident analyses of PBMR with the computer code SPECTRA

International Nuclear Information System (INIS)

Stempniewicz, Marek M.

2002-01-01

The SPECTRA code is an accident analysis code developed at NRG. It is designed for thermal-hydraulic analyses of nuclear or conventional power plants. The code is capable of analysing the whole power plant, including reactor vessel, primary system, various control and safety systems, containment and reactor building. The aim of the work presented in this paper was to prepare a preliminary thermal-hydraulic model of PBMR for SPECTRA, and perform steady state and accident analyses. In order to assess SPECTRA capability to model the PBMR reactors, a model of the INCOGEN system has been prepared first. Steady state and accident scenarios were analyzed for INCOGEN configuration. Results were compared to the results obtained earlier with INAS and OCTOPUS/PANTHERMIX. A good agreement was obtained. Results of accident analyses with PBMR model showed qualitatively good results. It is concluded that SPECTRA is a suitable tool for analyzing High Temperature Reactors, such as INCOGEN or for example PBMR (Pebble Bed Modular Reactor). Analyses of INCOGEN and PBMR systems showed that in all analyzed cases the fuel temperatures remained within the acceptable limits. Consequently there is no danger of release of radioactivity to the environment. It may be concluded that those are promising designs for future safe industrial reactors. (author)

Environmentally safe system for treatment of bio corrosion of ETICS

Directory of Open Access Journals (Sweden)

Minarovičová Katarína

2018-01-01

Full Text Available Effects of microorganisms on building facades are responsible for aesthetic, bio-geophysical and biogeochemical deterioration. The process of cleaning of contaminated facades involves the removal and eradication of micro flora on the surface of insulation using chemical products, killing cells and eliminating all living mass, including organic ingredients. The removal of bio corrosion coating from ETICS structure by means of chemical and preservative substances (biocides is currently the only effective and most used technology. Uncontrolled leaching of the used biocides is unacceptable. Meantime, new technology for environmentally safe maintenance of ETICS is needed. Scientists have been working on replacement the biocides currently used in facades treatment with eco-friendly biocides that have no negative effects on the environment or human beings. While the eco- treatment will be available, safe dewatering of chemicals being leached from the surface of the facade could be provided by e.g. special drain systems adjusted to the building type, use and age. The paper gives an overview of the problem in context of Slovakia and examples of leaching systems designed for new and renovated buildings.

Comparison of european computer codes relative to the aerosol behavior in PWR containment buildings during severe core damage accidents. (Modelling of steam condensation on the particles)

International Nuclear Information System (INIS)

Bunz, H.; Dunbar, L.H.; Fermandjian, J.; Lhiaubet, G.

1987-11-01

An aerosol code comparison exercise was performed within the framework of the Commission of European Communities (Division of Safety of Nuclear Installations). This exercise, focused on the process of steam condensation onto the aerosols occurring in PWR containment buildings during severe core damage accidents, has allowed to understand the discrepancies between the results obtained. These discrepancies are due, in particular, to whether the curvature effect is modelled or not in the codes

Comparison of building permit procedures in European Union countries

NARCIS (Netherlands)

Costa Branco De Oliveira Pedro, J.A.; Meijer, F.M.; Visscher, H.J.

2011-01-01

Building regulations set minimum requirements for safe, healthy, energy-efficient and accessible buildings. To guarantee that these requirements are applied, a building control system is indispensable. The trend towards a common market for construction products and services justifies gaining a

Modernising ATLAS Software Build Infrastructure

CERN Document Server

Ritsch, Elmar; The ATLAS collaboration

2017-01-01

In the last year ATLAS has radically updated its software development infrastructure hugely reducing the complexity of building releases and greatly improving build speed, flexibility and code testing. The first step in this transition was the adoption of CMake as the software build system over the older CMT. This required the development of an automated translation from the old system to the new, followed by extensive testing and improvements. This resulted in a far more standard build process that was married to the method of building ATLAS software as a series of $12$ separate projects from Subversion. We then proceeded with a migration of the code base from Subversion to Git. As the Subversion repository had been structured to manage each package more or less independently there was no simple mapping that could be used to manage the migration into Git. Instead a specialist set of scripts that captured the software changes across official software releases was developed. With some clean up of the repositor...

SEISMIC EVALUATION OF EXISTING MID-RISE REINFORCED CONCRETE BUILDINGS ACCORDING TO SPECIFICATION FOR BUILDING STRUCTURES TO BE BUILT IN DISASTER AREAS

Directory of Open Access Journals (Sweden)

Mehmet İNEL

2007-01-01

Full Text Available Over the past several decades, Turkey has been hit by devastating earthquakes and remarkable number of reinforced concrete buildings has been damaged in the high seismicity regions of our country. The aim of this study is to evaluate the seismic performance of the mid-rise reinforced concrete buildings that are major part of building stock of our earthquake-prone country, according to recent Turkish Earthquake Code. 4- and 7-story buildings were selected to represent mid-rise building stock. After determining the structural parameters, each building was subjected to pushover analysis and the capacity curves were obtained. Earthquake performance of each building was determined in the light of their capacity curves according to the recent Turkish Earthquake Code.

Fast and Safe Concrete Code Execution for Reinforcing Static Analysis and Verification

Directory of Open Access Journals (Sweden)

M. Belyaev

2015-01-01

Full Text Available The problem of improving precision of static analysis and verification techniques for C is hard due to simplification assumptions these techniques make about the code model. We present a novel approach to improving precision by executing the code model in a controlled environment that captures program errors and contract violations in a memory and time efficient way. We implemented this approach as an executor module Tassadar as a part of bounded model checker Borealis. We tested Tassadar on two test sets, showing that its impact on performance of Borealis is minimal.The article is published in the authors’ wording.

Safety analysis to support a safe operating envelope for fuel

International Nuclear Information System (INIS)

Gibb, R.A.; Reid, P.J.

1998-01-01

This paper presents an approach for defining a safe operating envelope for fuel. 'Safe operating envelope' is defined as an envelope of fuel parameters defined for application in safety analysis that can be related to, or used to define, the acceptable range of fuel conditions due to operational transients or deviations in fuel manufacturing processes. The paper describes the motivation for developing such a methodology. The methodology involved four steps: the update of fission product inventories, the review of sheath failure criteria, a review of input parameters to be used in fuel modelling codes, and the development of an improved fission product release code. This paper discusses the aspects of fuel sheath failure criteria that pertain to operating or manufacturing conditions and to the evaluation and selection of modelling input data. The other steps are not addressed in this paper since they have been presented elsewhere. (author)

Wood: a construction material for tall buildings

Science.gov (United States)

Wimmers, Guido

2017-12-01

Wood has great potential as a building material, because it is strong and lightweight, environmentally friendly and can be used in prefabricated buildings. However, only changes in building codes will make wood competitive with steel and concrete.

Canadian energy standards : residential energy code requirements

Energy Technology Data Exchange (ETDEWEB)

Cooper, K. [SAR Engineering Ltd., Burnaby, BC (Canada)

2006-09-15

A survey of residential energy code requirements was discussed. New housing is approximately 13 per cent more efficient than housing built 15 years ago, and more stringent energy efficiency requirements in building codes have contributed to decreased energy use and greenhouse gas (GHG) emissions. However, a survey of residential energy codes across Canada has determined that explicit demands for energy efficiency are currently only present in British Columbia (BC), Manitoba, Ontario and Quebec. The survey evaluated more than 4300 single-detached homes built between 2000 and 2005 using data from the EnerGuide for Houses (EGH) database. House area, volume, airtightness and construction characteristics were reviewed to create archetypes for 8 geographic areas. The survey indicated that in Quebec and the Maritimes, 90 per cent of houses comply with ventilation system requirements of the National Building Code, while compliance in the rest of Canada is much lower. Heat recovery ventilation use is predominant in the Atlantic provinces. Direct-vent or condensing furnaces constitute the majority of installed systems in provinces where natural gas is the primary space heating fuel. Details of Insulation levels for walls, double-glazed windows, and building code insulation standards were also reviewed. It was concluded that if R-2000 levels of energy efficiency were applied, total average energy consumption would be reduced by 36 per cent in Canada. 2 tabs.

Comparison Of Seismic Performance Of Erciş Cultural Center Building With Observed And Calculated By Turkish Earthquake Code-2007

Directory of Open Access Journals (Sweden)

Recep Ali Dedecan

2013-08-01

Full Text Available The goal of this paper is to review the validity of seismic assessment procedure given in the Turkish Earthquake Code by comparing the assessment results with real structures from Eastern Turkey, where the 2011 Van earthquake occurred. To test the analysis methods for a typically suitable structure, the cultural center building at Erciş with 3 stories, is selected. In order to compare the results of the three different analysis techniques, for an identical earthquake, the ground motion used in analysis was characterized by equivalent elastic earthquake spectra, which were developed from available time history at the nearest construction site. It was found that the damage predictions by using the by Turkish Earthquake Code procedures point out the different level of damages. But, it is concluded that nonlinear time history analysis calculated the best estimation of the damage observed in the site.

78 FR 69839 - Building Technologies Office Prioritization Tool

Science.gov (United States)

2013-11-21

... standards and building codes to ensure energy savings within buildings. BTO has developed a new technology... DEPARTMENT OF ENERGY Building Technologies Office Prioritization Tool AGENCY: Office of Energy....S. Department of Energy's (DOE) Building Technologies Office (BTO) developed the Prioritization Tool...

Implementation of project Safe in Amber. Verification study for SFR 1 SAR-08

Energy Technology Data Exchange (ETDEWEB)

Thomson, Gavin; Herben, Martin; Lloyd, Pam; Rose, Danny; Smith, Chris; Barraclough, Ian (Enviros Consulting Ltd (GB))

2008-03-15

This report documents an exercise in which AMBER has been used to represent the models used in Project SAFE, a safety assessment undertaken on SFR 1. (AMBER is a flexible, graphical-user-interface based tool that allows users to build their own dynamic compartmental models to represent the migration, degradation and fate of contaminants in an environmental system. AMBER allows the user to assess routine, accidental and long-term contaminant release.) AMBER has been used to undertake assessment calculations on all of the disposal system, including all disposal tunnels and the Silo, the geosphere and several biosphere modules. The near-field conceptual models were implemented with minimal changes to the approach undertaken previously in Project SAFE. Model complexity varied significantly between individual disposal facilities increasing significantly from the BLA to the BTF and BMA tunnels and Silo. Radionuclide transport through the fractured granite geosphere was approximated using a compartment model approach in AMBER. Several biosphere models were implemented in AMBER including reasonable biosphere development, which considered the evolution of the Forsmark area from coastal to lacustrine to agricultural environments in response to land uplift. Parameters were sampled from distributions and simulations were run for 1,000 realisations. In undertaking the comparison of AMBER with the various codes and calculation tools used in Project SAFE it was necessary to undertake a detailed analysis of the modelling approach previously adopted, with particular focus given to the near-field models. As a result some discrepancies in the implementation of the models and documentation were noted. The exercise demonstrates that AMBER is fully capable of representing the features of the SFR 1 disposal system in a safety assessment suitable for SAR-08

Implementation of project Safe in Amber. Verification study for SFR 1 SAR-08

International Nuclear Information System (INIS)

Thomson, Gavin; Herben, Martin; Lloyd, Pam; Rose, Danny; Smith, Chris; Barra clough, Ian

2008-03-01

This report documents an exercise in which AMBER has been used to represent the models used in Project SAFE, a safety assessment undertaken on SFR 1. (AMBER is a flexible, graphical-user-interface based tool that allows users to build their own dynamic compartmental models to represent the migration, degradation and fate of contaminants in an environmental system. AMBER allows the user to assess routine, accidental and long-term contaminant release.) AMBER has been used to undertake assessment calculations on all of the disposal system, including all disposal tunnels and the Silo, the geosphere and several biosphere modules. The near-field conceptual models were implemented with minimal changes to the approach undertaken previously in Project SAFE. Model complexity varied significantly between individual disposal facilities increasing significantly from the BLA to the BTF and BMA tunnels and Silo. Radionuclide transport through the fractured granite geosphere was approximated using a compartment model approach in AMBER. Several biosphere models were implemented in AMBER including reasonable biosphere development, which considered the evolution of the Forsmark area from coastal to lacustrine to agricultural environments in response to land uplift. Parameters were sampled from distributions and simulations were run for 1,000 realisations. In undertaking the comparison of AMBER with the various codes and calculation tools used in Project SAFE it was necessary to undertake a detailed analysis of the modelling approach previously adopted, with particular focus given to the near-field models. As a result some discrepancies in the implementation of the models and documentation were noted. The exercise demonstrates that AMBER is fully capable of representing the features of the SFR 1 disposal system in a safety assessment suitable for SAR-08

Management for nuclear power plants for safe operation

International Nuclear Information System (INIS)

Kueffer, K.

1981-01-01

This lecture covers management aspects which have an immediate bearing on safety and identifies the objectives and tasks of management which are required for safe operation of a nuclear power plant and is based on the Codes of Practice and Safety Guides of the IAEA as well as arrangements in use at the Swiss Nuclear Power Station Beznau. (orig./RW)

A SciCode web site: building bridges between owners and users

Energy Technology Data Exchange (ETDEWEB)

Gaver, C. [Atomic Energy of Canada Ltd., Mississauga, Ontario (Canada)

2000-07-01

Web technology is a tool that is gaining in popularity. Properly used, it is a powerful tool that has tremendous potential for providing better communication. It can also be effective as a training tool, an information-sharing tool, and as a means of simplifying work load, and facilitating compliance with Company procedures. The issue is one of communication. The challenge facing many large or geographically-distributed companies is how to communicate information to their staff and to their customers. Procedures overseeing quality-assurance programs and commitment to ensuring the quality of products need to be communicated to customers. Equally important is customer feedback. This information from users becomes the kernel for future product development. The issue is even more important when speaking of scientific analysis computer programs (SciCodes). Regular ongoing communication between Primary Holders and End Users is essential in the development and use of SciCodes. Without this communication, quality assurance is at risk. Quality assurance processes are an integral part in developing any SciCode. End Users also have a role to play. Primary Holders keep End Users informed of improvements or new releases. End Users must ensure they act on this information. Equally important, End Users must communicate problems or suggestions to the Primary Holder to remedy or incorporate in new releases. In other words, quality assurance processes become most effective when both Primary Holder and End Users are involved. This requires communication. Web technology offers AECL a means of providing regular, ongoing communication between its scientific-code (SciCode) Primary Holders-Owner Branches and the End Users of these codes within and outside the Company. Using the experience we have gained by developing the Y2K SciCode Web sites, setting up online documentation systems, and incorporating lessons learned from the Y2K project we have developed a model that is geared to

A SciCode web site: building bridges between owners and users

International Nuclear Information System (INIS)

Gaver, C.

2000-01-01

Web technology is a tool that is gaining in popularity. Properly used, it is a powerful tool that has tremendous potential for providing better communication. It can also be effective as a training tool, an information-sharing tool, and as a means of simplifying work load, and facilitating compliance with Company procedures. The issue is one of communication. The challenge facing many large or geographically-distributed companies is how to communicate information to their staff and to their customers. Procedures overseeing quality-assurance programs and commitment to ensuring the quality of products need to be communicated to customers. Equally important is customer feedback. This information from users becomes the kernel for future product development. The issue is even more important when speaking of scientific analysis computer programs (SciCodes). Regular ongoing communication between Primary Holders and End Users is essential in the development and use of SciCodes. Without this communication, quality assurance is at risk. Quality assurance processes are an integral part in developing any SciCode. End Users also have a role to play. Primary Holders keep End Users informed of improvements or new releases. End Users must ensure they act on this information. Equally important, End Users must communicate problems or suggestions to the Primary Holder to remedy or incorporate in new releases. In other words, quality assurance processes become most effective when both Primary Holder and End Users are involved. This requires communication. Web technology offers AECL a means of providing regular, ongoing communication between its scientific-code (SciCode) Primary Holders-Owner Branches and the End Users of these codes within and outside the Company. Using the experience we have gained by developing the Y2K SciCode Web sites, setting up online documentation systems, and incorporating lessons learned from the Y2K project we have developed a model that is geared to

Error-correction coding for digital communications

Science.gov (United States)

Clark, G. C., Jr.; Cain, J. B.

This book is written for the design engineer who must build the coding and decoding equipment and for the communication system engineer who must incorporate this equipment into a system. It is also suitable as a senior-level or first-year graduate text for an introductory one-semester course in coding theory. Fundamental concepts of coding are discussed along with group codes, taking into account basic principles, practical constraints, performance computations, coding bounds, generalized parity check codes, polynomial codes, and important classes of group codes. Other topics explored are related to simple nonalgebraic decoding techniques for group codes, soft decision decoding of block codes, algebraic techniques for multiple error correction, the convolutional code structure and Viterbi decoding, syndrome decoding techniques, and sequential decoding techniques. System applications are also considered, giving attention to concatenated codes, coding for the white Gaussian noise channel, interleaver structures for coded systems, and coding for burst noise channels.

RESRAD-BUILD: A computer model for analyzing the radiological doses resulting from the remediation and occupancy of buildings contaminated with radioactive material

International Nuclear Information System (INIS)

Yu, C.; LePoire, D.J.; Jones, L.G.

1994-11-01

The RESRAD-BUILD computer code is a pathway analysis model designed to evaluate the potential radiological dose incurred by an individual who works or lives in a building contaminated with radioactive material. The transport of radioactive material inside the building from one compartment to another is calculated with an indoor air quality model. The air quality model considers the transport of radioactive dust particulates and radon progeny due to air exchange, deposition and resuspension, and radioactive decay and ingrowth. A single run of the RESRAD-BUILD code can model a building with up to: three compartments, 10 distinct source geometries, and 10 receptor locations. A shielding material can be specified between each source-receptor pair for external gamma dose calculations. Six exposure pathways are considered in the RESRAD-BUILD code: (1) external exposure directly from the source; (2) external exposure to materials deposited on the floor; (3) external exposure due to air submersion; (4) inhalation of airborne radioactive particulates; (5) inhalation of aerosol indoor radon progeny; and (6) inadvertent ingestion of radioactive material, either directly from the sources or from materials deposited on the surfaces of the building compartments

Zero Energy Building

DEFF Research Database (Denmark)

Marszal, Anna Joanna; Heiselberg, Per; Bourrelle, J.S.

2011-01-01

The concept of Zero Energy Building (ZEB) has gained wide international attention during last few years and is now seen as the future target for the design of buildings. However, before being fully implemented in the national building codes and international standards, the ZEB concept requires......, (4) the type of energy balance, (5) the accepted renewable energy supply options, (6) the connection to the energy infrastructure and (7) the requirements for the energy efficiency, the indoor climate and in case of gird connected ZEB for the building–grid interaction. This paper focuses...

Safe management of wastes from the mining and milling of uranium and thorium ores

International Nuclear Information System (INIS)

1987-01-01

Wastes from the mining and milling of uranium and thorium ores pose potential environmental and public health problems because of their radioactivity and chemical composition. This document consists of two parts: a Code of Practice (Part I) and a Guide to the Code (Part II). The Code sets forth the requirements for the safe and responsible handling of the wastes resulting from the mining and milling of uranium and thorium ores, while the Guide presents further guidance in the use of the Code together with some discussion of the technology and concepts involved

Modernising ATLAS Software Build Infrastructure

CERN Document Server

Gaycken, Goetz; The ATLAS collaboration

2017-01-01

In the last year ATLAS has radically updated its software development infrastructure hugely reducing the complexity of building releases and greatly improving build speed, flexibility and code testing. The first step in this transition was the adoption of CMake as the software build system over the older CMT. This required the development of an automated translation from the old system to the new, followed by extensive testing and improvements. This resulted in a far more standard build process that was married to the method of building ATLAS software as a series of 12 separate projects from SVN. We then proceeded with a migration of its code base from SVN to git. As the SVN repository had been structured to manage each package more or less independently there was no simple mapping that could be used to manage the migration into git. Instead a specialist set of scripts that captured the software changes across official software releases was developed. With some clean up of the repository and the policy of onl...

Programming Entity Framework Code First

CERN Document Server

Lerman, Julia

2011-01-01

Take advantage of the Code First data modeling approach in ADO.NET Entity Framework, and learn how to build and configure a model based on existing classes in your business domain. With this concise book, you'll work hands-on with examples to learn how Code First can create an in-memory model and database by default, and how you can exert more control over the model through further configuration. Code First provides an alternative to the database first and model first approaches to the Entity Data Model. Learn the benefits of defining your model with code, whether you're working with an exis

Safe transport of radioactive materials in Egypt

International Nuclear Information System (INIS)

El-Shinawy, R.M.K.

1994-01-01

In Egypt the national regulations for safe transport of radioactive materials (RAM) are based on the International Atomic Energy Agency (IAEA) regulations. In addition, regulations for the safe transport of these materials through the Suez Canal (SC) were laid down by the Egyptian Atomic Energy Authority (EAEA) and the Suez Canal Authority (SCA). They are continuously updated to meet the increased knowledge and the gained experience. The technical and protective measures taken during transport of RAM through SC are mentioned. Assessment of the impact of transporting radioactive materials through the Suez Canal using the INTERTRAN computer code was carried out in cooperation with IAEA. The transported activities and empty containers, the number of vessels carrying RAM through the canal from 1963 and 1991 and their nationalities are also discussed. The protective measures are mentioned. A review of the present situation of the radioactive wastes storage facilities at the Atomic Energy site at Inshas is given along with the regulation for safe transportation and disposal of radioactive wastes. (Author)

City Reach Code Technical Support Document

Energy Technology Data Exchange (ETDEWEB)

Athalye, Rahul A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chen, Yan [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhang, Jian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Liu, Bing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Frankel, Mark [New Buildings Inst., Portland, OR (United States); Lyles, Mark [New Buildings Inst., Portland, OR (United States)

2017-10-31

This report describes and analyzes a set of energy efficiency measures that will save 20% energy over ASHRAE Standard 90.1-2013. The measures will be used to formulate a Reach Code for cities aiming to go beyond national model energy codes. A coalition of U.S. cities together with other stakeholders wanted to facilitate the development of voluntary guidelines and standards that can be implemented in stages at the city level to improve building energy efficiency. The coalition's efforts are being supported by the U.S. Department of Energy via Pacific Northwest National Laboratory (PNNL) and in collaboration with the New Buildings Institute.

Strategies for Sustainable Comfort in Buildings

DEFF Research Database (Denmark)

Nørgaard, Jørgen

1997-01-01

these goals include phasing out all use of electricity for space heating and for hot water supply. Furthermore building codes should require new buildings to be very well insulated, 30-40 cm mineral wool, for instance, and low energy windows. Similar codes, although not always as strict, should be applied......It is possible within some decades to achieve environmental sustainability in the building sector and at the same time provide a comfortable and healthy life for all Europeans as well as leaving that option open for other people in the world.Buildings are charcterized by having the longest lifetime...... of all capital in our societies, often more than a hundred years. For that reason they should never be designed on the bases of just present cheap energy supply and energy system, but with the long term outlook and risks in mind. New buildings can be designed to require essentially no space heating...

Rise of the build infrastructure

International Nuclear Information System (INIS)

Eulisse, Giulio; Muzaffar, Shahzad; Abdurachmanov, David; Mendez, David

2014-01-01

CMS Offline Software, CMSSW, is an extremely large software project, with roughly 3 millions lines of code, two hundreds of active developers and two to three active development branches. Given the scale of the problem, both from a technical and a human point of view, being able to keep on track such a large project, bug free, and to deliver builds for different architectures is a challenge in itself. Moreover the challenges posed by the future migration of CMSSW to multithreading also require adapting and improving our QA tools. We present the work done in the last two years in our build and integration infrastructure, particularly in the form of improvements to our build tools, in the simplification and extensibility of our build infrastructure and the new features added to our QA and profiling tools. Finally we present our plans for the future directions for code management and how this reflects on our workflows and the underlying software infrastructure.

Tall Buildings Initiative

Science.gov (United States)

Initiative 2017 TBI Guidelines Version 2.03 Now Available Screen Shot 2017-10-10 at 3.05.10 PM PEER has just initiative to develop design criteria that will ensure safe and usable tall buildings following future earthquakes. Download the primary product of this initiative: Guidelines for Performance-Based Seismic Design

High dynamic range coding imaging system

Science.gov (United States)

Wu, Renfan; Huang, Yifan; Hou, Guangqi

2014-10-01

We present a high dynamic range (HDR) imaging system design scheme based on coded aperture technique. This scheme can help us obtain HDR images which have extended depth of field. We adopt Sparse coding algorithm to design coded patterns. Then we utilize the sensor unit to acquire coded images under different exposure settings. With the guide of the multiple exposure parameters, a series of low dynamic range (LDR) coded images are reconstructed. We use some existing algorithms to fuse and display a HDR image by those LDR images. We build an optical simulation model and get some simulation images to verify the novel system.

You know the Science. Do you know your Code?

CERN Multimedia

CERN. Geneva

2014-01-01

This talk is about automated code analysis and transformation tools to support scientific computing. Code bases are difficult to manage because of size, age, or safety requirements. Tools can help scientists and IT engineers understand their code, locate problems, improve quality. Tools can also help transform the code, by implementing complex refactorings, replatforming, or migration to a modern language. Such tools are themselves difficult to build. This talk describes DMS, a meta-tool for building software analysis tools. DMS is a kind of generalized compiler, and can be configured to process arbitrary programming languages, to carry out arbitrary analyses, and to convert specifications into running code. It has been used for a variety of purposes, including converting embedded mission software in the US B-2 Stealth Bomber, providing the US Social Security Administration with a deep view how their 200 millions lines of COBOL are connected, and reverse-engineering legacy factory process control code i...

Building energy efficiency in rural China

International Nuclear Information System (INIS)

Evans, Meredydd; Yu, Sha; Song, Bo; Deng, Qinqin; Liu, Jing; Delgado, Alison

2014-01-01

Rural buildings in China now account for more than half of China's total building energy use. Forty percent of the floorspace in China is in rural villages and towns. Most of these buildings are very energy inefficient, and may struggle to provide for basic needs. They are cold in the winter, and often experience indoor air pollution from fuel use. The Chinese government plans to adopt a voluntary building energy code, or design standard, for rural homes. The goal is to build on China's success with codes in urban areas to improve efficiency and comfort in rural homes. The Chinese government recognizes rural buildings represent a major opportunity for improving national building energy efficiency. The challenges of rural China are also greater than those of urban areas in many ways because of the limited local capacity and low income levels. The Chinese government wants to expand on new programs to subsidize energy efficiency improvements in rural homes to build capacity for larger-scale improvement. This article summarizes the trends and status of rural building energy use in China. It then provides an overview of the new rural building design standard, and describes options and issues to move forward with implementation. - Highlights: • Building energy use is larger in rural China than in cities. • Rural buildings are very energy intensive, and energy use is growing with incomes. • A new design standard aims to help rural communities build more efficiently. • Important challenges remain with implementation

Is the international safety management code an organisational tool ...

African Journals Online (AJOL)

The birth of the International Management Code for the Safe Operation of Ships and for Pollution Prevention (hereinafter ISM Code) is said to a reaction to the sinking of the Herald of free Enterprise on 6th March 1987.The human element is said to be a generic term used to describe what makes humans behave the way ...

Removal Action Workplan for the 105-DR and 105-F Building Interim Safe Storage Projects and Ancillary Buildings

International Nuclear Information System (INIS)

Rodovsky, T. J.

1999-01-01

This document is the removal action workplan (RAW) for the 105-DR and 105-F Reactor Buildings and ancillary facilities. These buildings and facilities are located in the 100-D/DR and 100-F Areas of the Hanford Site in Benton County, Washington, which is owned and operated by the U.S. Department of Energy (DOE). The 100 Areas (including 100-D/DR and 100-F Areas) of the Hanford Site were placed on the U.S. Environmental Protection Agency's (EPA) National Priorities List under the Comprehensive Environmental Response, Compensation,and Liability Act of 1980 (CERCLA). DOE has determined that hazardous substances in the 105-DR and 105-F Reactor Buildings and four ancillary facilities present a potential threat to human health or the environment DOE has also determined that a non-time critical removal action is warranted at these facilities

Overview of the ArbiTER edge plasma eigenvalue code

Science.gov (United States)

Baver, Derek; Myra, James; Umansky, Maxim

2011-10-01

The Arbitrary Topology Equation Reader, or ArbiTER, is a flexible eigenvalue solver that is currently under development for plasma physics applications. The ArbiTER code builds on the equation parser framework of the existing 2DX code, extending it to include a topology parser. This will give the code the capability to model problems with complicated geometries (such as multiple X-points and scrape-off layers) or model equations with arbitrary numbers of dimensions (e.g. for kinetic analysis). In the equation parser framework, model equations are not included in the program's source code. Instead, an input file contains instructions for building a matrix from profile functions and elementary differential operators. The program then executes these instructions in a sequential manner. These instructions may also be translated into analytic form, thus giving the code transparency as well as flexibility. We will present an overview of how the ArbiTER code is to work, as well as preliminary results from early versions of this code. Work supported by the U.S. DOE.

Safe Software for Space Applications: Building on the DO-178 Experience

Science.gov (United States)

Dorsey, Cheryl A.; Dorsey, Timothy A.

2013-09-01

DO-178, Software Considerations in Airborne Systems and Equipment Certification, is the well-known international standard dealing with the assurance of software used in airborne systems [1,2]. Insights into the DO-178 experiences, strengths and weaknesses can benefit the international space community. As DO-178 is an excellent standard for safe software development when used appropriately, this paper provides lessons learned and suggestions for using it effectively.

Extension of the code COCOSYS to a dispersion code for smoke and carbon monoxide

International Nuclear Information System (INIS)

Sdouz, Gert; Mayrhofer, Robert

2009-01-01

The code COCOSYS (Containment Code SYStem) was developed by GRS in Germany to simulate processes and nuclear plant states during severe accidents in the containments of light water reactors. It contains several physical models, especially a module for aerosol behaviour. The goal of this work was to extend COCOSYS for applications in more general geometries mainly for complex public buildings. For the application in public buildings models for air condition systems and different boundary conditions according to different environments were developed. The principal application of the extended code COCOSYS is in the area of emergency situations especially in the simulation for carbon monoxide and smoke dispersion. After developing and implementing the new models several test calculations were performed to evaluate the functionality of the extended code. The comparison of the results with those of the original COCOSYS code showed no discrepancies. For the first realistic application several fire emergency scenarios in the Vienna General Hospital (AKH) were selected in agreement with the fire department of the hospital. One of the scenarios addresses the danger of carbon monoxide (CO) and smoke leaking into a fire protection section through a damaged fire protection flap. As a result of the dispersion simulation the CO-concentration in all of the rooms is obtained. Together with additional results as deposition and smoke dispersion the outcome of the simulation can be used for training. Among the next steps are the validation of the new models and the selection of critical scenarios. (author)

Lets build a safe SA out of love, not from fear (Interview)

CSIR Research Space (South Africa)

Holtman, B

2008-01-18

Full Text Available her interview with Redi Ireko of Monitoring South Africa said that South Africans can overcome the problem of crime by painting and articulating how it will look like in a safe South Africa. South Africans should have a vision of how all will look like...

Electrical safety code manual a plan language guide to national electrical code, OSHA and NFPA 70E

CERN Document Server

Keller, Kimberley

2010-01-01

Safety in any workplace is extremely important. In the case of the electrical industry, safety is critical and the codes and regulations which determine safe practices are both diverse and complicated. Employers, electricians, electrical system designers, inspectors, engineers and architects must comply with safety standards listed in the National Electrical Code, OSHA and NFPA 70E. Unfortunately, the publications which list these safety requirements are written in very technically advanced terms and the average person has an extremely difficult time understanding exactly what they need to

Study on the hydrogen explosion risk at reactor building during a severe accident

Energy Technology Data Exchange (ETDEWEB)

NONE

2013-08-15

JNES carried out analysis on the hydrogen mixing and explosion at reactor building with CFD code and explosion analysis code to evaluate what exactly has happened at the reactor buildings of the Fukushima Daiichi NPS. Based on the MELCOR severe accident analysis results of Fukushima Daiichi Unit 1 and Unit 3, sensitivity study using the CFD code FLUENT was carried out on the parameter of the release rate, total mass of hydrogen gas, the release path between reactor building and PCV, and so on. Then an analysis using AUTODYN code was carried out to investigate the explosion at the reactor building of Unit 4 as well as Unit 1 and, Unit 3. With those analysis results it became possible to estimate the leaked path and the total amount of leaked hydrogen gas from PCV to reactor building. (author)

Recommended Practices for the Safe Design and Operation of Flywheels

Energy Technology Data Exchange (ETDEWEB)

Bender, Donald Arthur [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-12-01

Flywheel energy storage systems are in use globally in increasing numbers . No codes pertaining specifically to flywheel energy storage exist. A number of industrial incidents have occurred. This protocol recommends a technical basis for safe flywheel de sign and operation for consideration by flywheel developers, users of flywheel systems and standards setting organizations.

Evaluation and considerations about fundamental periods of damaged reinforced concrete buildings

Directory of Open Access Journals (Sweden)

R. Ditommaso

2013-07-01

Full Text Available The aim of this paper is an empirical estimation of the fundamental period of reinforced concrete buildings and its variation due to structural and non-structural damage. The 2009 L'Aquila earthquake has highlighted the mismatch between experimental data and code provisions value not only for undamaged buildings but also for the damaged ones. The 6 April 2009 L'Aquila earthquake provided the first opportunity in Italy to estimate the fundamental period of reinforced concrete (RC buildings after a strong seismic sequence. A total of 68 buildings with different characteristics, such as age, height and damage level, have been investigated by performing ambient vibration measurements that provided their fundamental translational period. Four different damage levels were considered according with the definitions by EMS 98 (European Macroseismic Scale, trying to regroup the estimated fundamental periods versus building heights according to damage. The fundamental period of RC buildings estimated for low damage level is equal to the previous relationship obtained in Italy and Europe for undamaged buildings, well below code provisions. When damage levels are higher, the fundamental periods increase, but again with values much lower than those provided by codes. Finally, the authors suggest a possible update of the code formula for the simplified estimation of the fundamental period of vibration for existing RC buildings, taking into account also the inelastic behaviour.

ATLAS software configuration and build tool optimisation

Science.gov (United States)

Rybkin, Grigory; Atlas Collaboration

2014-06-01

ATLAS software code base is over 6 million lines organised in about 2000 packages. It makes use of some 100 external software packages, is developed by more than 400 developers and used by more than 2500 physicists from over 200 universities and laboratories in 6 continents. To meet the challenge of configuration and building of this software, the Configuration Management Tool (CMT) is used. CMT expects each package to describe its build targets, build and environment setup parameters, dependencies on other packages in a text file called requirements, and each project (group of packages) to describe its policies and dependencies on other projects in a text project file. Based on the effective set of configuration parameters read from the requirements files of dependent packages and project files, CMT commands build the packages, generate the environment for their use, or query the packages. The main focus was on build time performance that was optimised within several approaches: reduction of the number of reads of requirements files that are now read once per package by a CMT build command that generates cached requirements files for subsequent CMT build commands; introduction of more fine-grained build parallelism at package task level, i.e., dependent applications and libraries are compiled in parallel; code optimisation of CMT commands used for build; introduction of package level build parallelism, i. e., parallelise the build of independent packages. By default, CMT launches NUMBER-OF-PROCESSORS build commands in parallel. The other focus was on CMT commands optimisation in general that made them approximately 2 times faster. CMT can generate a cached requirements file for the environment setup command, which is especially useful for deployment on distributed file systems like AFS or CERN VMFS. The use of parallelism, caching and code optimisation significantly-by several times-reduced software build time, environment setup time, increased the efficiency of

Multiple application coded switch development report

International Nuclear Information System (INIS)

Bernal, E.L.; Kestly, J.D.

1979-03-01

The development of the Multiple Application Coded Switch (MACS) and its related controller are documented; the functional and electrical characteristics are described; the interface requirements defined, and a troubleshooting guide provided. The system was designed for the Safe Secure Trailer System used for secure transportation of nuclear material

Thermal comfort in residential buildings by the millions

DEFF Research Database (Denmark)

Østergård, Torben; Maagaard, Steffen; Jensen, Rasmus Lund

2016-01-01

In Danish building code and many design briefings, criteria regarding thermal comfort are defined for “critical” rooms in residential buildings. Identifying the critical room is both difficult and time-consuming for large, multistory buildings. To reduce costs and time, such requirement often...

Safe sex

Science.gov (United States)

... sex; Sexually transmitted - safe sex; GC - safe sex; Gonorrhea - safe sex; Herpes - safe sex; HIV - safe sex; ... contact. STIs include: Chlamydia Genital herpes Genital warts Gonorrhea Hepatitis HIV HPV Syphilis STIs are also called ...

Energy efficiency outlook in China’s urban buildings sector through 2030

International Nuclear Information System (INIS)

McNeil, Michael A.; Feng, Wei; Rue du Can, Stephane de la; Khanna, Nina Zheng; Ke, Jing; Zhou, Nan

2016-01-01

This study uses bottom-up modeling framework in order to quantify potential energy savings and emission reduction impacts from the implementation of energy efficiency programs in the building sector in China. Policies considered include (1) accelerated building codes in residential and commercial buildings, (2) increased penetration of district heat metering and controls, (3) district heating efficiency improvement, (4) building energy efficiency labeling programs and (5) retrofits of existing commercial buildings. Among these programs, we found that the implementation of building codes provide by far the largest savings opportunity, leading to an overall 17% reduction in overall space heating and cooling demand relative to the baseline. Second are energy efficiency labels with 6%, followed by reductions of losses associated with district heating representing 4% reduction and finally, retrofits representing only about a 1% savings. - Highlights: • We use a bottom-up modeling approach to quantify emission reduction from efficiency programs. • Heating and cooling are the main focus of this study. • We find that building codes lead to 17% reduction compare to the baseline. • Other programs analyzed concern district heat, building labeling and retrofits of buildings.

Safe Handling of Radioisotopes

International Nuclear Information System (INIS)

1958-01-01

Under its Statute the International Atomic Energy Agency is empowered to provide for the application of standards of safety for protection against radiation to its own operations and to operations making use of assistance provided by it or with which it is otherwise directly associated. To this end authorities receiving such assistance are required to observe relevant health and safety measures prescribed by the Agency. As a first step, it has been considered an urgent task to provide users of radioisotopes with a manual of practice for the safe handling of these substances. Such a manual is presented here and represents the first of a series of manuals and codes to be issued by the Agency. It has been prepared after careful consideration of existing national and international codes of radiation safety, by a group of international experts and in consultation with other international bodies. At the same time it is recommended that the manual be taken into account as a basic reference document by Member States of the Agency in the preparation of national health and safety documents covering the use of radioisotopes.

Calculations on safe storage and transportation of radioactive materials

Energy Technology Data Exchange (ETDEWEB)

Hathout, A M; El-Messiry, A M; Amin, E [National Center for Nuclear Safety and Radiation Control and AEA, Cairo (Egypt)

1997-12-31

In this work the safe storage and transportation of fresh fuel as a radioactive material studied. Egypt planned ET RR 2 reactor which is of relatively high power and would require adequate handling and transportation. Therefore, the present work is initiated to develop a procedure for safe handling and transportation of radioactive materials. The possibility of reducing the magnitude of radiation transmitted on the exterior of the packages is investigated. Neutron absorbers are used to decrease the neutron flux. Criticality calculations are carried out to ensure the achievement of subcriticality so that the inherent safety can be verified. The discrete ordinate transport code ANISN was used. The results show good agreement with other techniques. 2 figs., 2 tabs.

Nuclear-thermal-coupled optimization code for the fusion breeding blanket conceptual design

International Nuclear Information System (INIS)

Li, Jia; Jiang, Kecheng; Zhang, Xiaokang; Nie, Xingchen; Zhu, Qinjun; Liu, Songlin

2016-01-01

Highlights: • A nuclear-thermal-coupled predesign code has been developed for optimizing the radial build arrangement of fusion breeding blanket. • Coupling module aims at speeding up the efficiency of design progress by coupling the neutronics calculation code with the thermal-hydraulic analysis code. • Radial build optimization algorithm aims at optimal arrangement of breeding blanket considering one or multiple specified objectives subject to the design criteria such as material temperature limit and available TBR. - Abstract: Fusion breeding blanket as one of the key in-vessel components performs the functions of breeding the tritium, removing the nuclear heat and heat flux from plasma chamber as well as acting as part of shielding system. The radial build design which determines the arrangement of function zones and material properties on the radial direction is the basis of the detailed design of fusion breeding blanket. For facilitating the radial build design, this study aims for developing a pre-design code to optimize the radial build of blanket with considering the performance of nuclear and thermal-hydraulic simultaneously. Two main features of this code are: (1) Coupling of the neutronics analysis with the thermal-hydraulic analysis to speed up the analysis progress; (2) preliminary optimization algorithm using one or multiple specified objectives subject to the design criteria in the form of constrains imposed on design variables and performance parameters within the possible engineering ranges. This pre-design code has been applied to the conceptual design of water-cooled ceramic breeding blanket in project of China fusion engineering testing reactor (CFETR).

Nuclear-thermal-coupled optimization code for the fusion breeding blanket conceptual design

Energy Technology Data Exchange (ETDEWEB)

Li, Jia, E-mail: lijia@ustc.edu.cn [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027, Anhui (China); Jiang, Kecheng; Zhang, Xiaokang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031, Anhui (China); Nie, Xingchen [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei 230027, Anhui (China); Zhu, Qinjun; Liu, Songlin [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei 230031, Anhui (China)

2016-12-15

Highlights: • A nuclear-thermal-coupled predesign code has been developed for optimizing the radial build arrangement of fusion breeding blanket. • Coupling module aims at speeding up the efficiency of design progress by coupling the neutronics calculation code with the thermal-hydraulic analysis code. • Radial build optimization algorithm aims at optimal arrangement of breeding blanket considering one or multiple specified objectives subject to the design criteria such as material temperature limit and available TBR. - Abstract: Fusion breeding blanket as one of the key in-vessel components performs the functions of breeding the tritium, removing the nuclear heat and heat flux from plasma chamber as well as acting as part of shielding system. The radial build design which determines the arrangement of function zones and material properties on the radial direction is the basis of the detailed design of fusion breeding blanket. For facilitating the radial build design, this study aims for developing a pre-design code to optimize the radial build of blanket with considering the performance of nuclear and thermal-hydraulic simultaneously. Two main features of this code are: (1) Coupling of the neutronics analysis with the thermal-hydraulic analysis to speed up the analysis progress; (2) preliminary optimization algorithm using one or multiple specified objectives subject to the design criteria in the form of constrains imposed on design variables and performance parameters within the possible engineering ranges. This pre-design code has been applied to the conceptual design of water-cooled ceramic breeding blanket in project of China fusion engineering testing reactor (CFETR).

Reversible machine code and its abstract processor architecture

DEFF Research Database (Denmark)

Axelsen, Holger Bock; Glück, Robert; Yokoyama, Tetsuo

2007-01-01

A reversible abstract machine architecture and its reversible machine code are presented and formalized. For machine code to be reversible, both the underlying control logic and each instruction must be reversible. A general class of machine instruction sets was proven to be reversible, building...

Analysis of quantum error-correcting codes: Symplectic lattice codes and toric codes

Science.gov (United States)

Harrington, James William

Quantum information theory is concerned with identifying how quantum mechanical resources (such as entangled quantum states) can be utilized for a number of information processing tasks, including data storage, computation, communication, and cryptography. Efficient quantum algorithms and protocols have been developed for performing some tasks (e.g. , factoring large numbers, securely communicating over a public channel, and simulating quantum mechanical systems) that appear to be very difficult with just classical resources. In addition to identifying the separation between classical and quantum computational power, much of the theoretical focus in this field over the last decade has been concerned with finding novel ways of encoding quantum information that are robust against errors, which is an important step toward building practical quantum information processing devices. In this thesis I present some results on the quantum error-correcting properties of oscillator codes (also described as symplectic lattice codes) and toric codes. Any harmonic oscillator system (such as a mode of light) can be encoded with quantum information via symplectic lattice codes that are robust against shifts in the system's continuous quantum variables. I show the existence of lattice codes whose achievable rates match the one-shot coherent information over the Gaussian quantum channel. Also, I construct a family of symplectic self-dual lattices and search for optimal encodings of quantum information distributed between several oscillators. Toric codes provide encodings of quantum information into two-dimensional spin lattices that are robust against local clusters of errors and which require only local quantum operations for error correction. Numerical simulations of this system under various error models provide a calculation of the accuracy threshold for quantum memory using toric codes, which can be related to phase transitions in certain condensed matter models. I also present

Development of safety enhancement technology of containment building

International Nuclear Information System (INIS)

Seo, Jeong Moon; Choun, Y. S.; Choi, I. K.

2002-04-01

This study consists of four research areas, (1) Seismic safety assessment, (2) Aging assessment of a containment building, (3) Prediction of long-term behavior and analysis of a containment building, (4) Performance verification of a containment building. In the seismic safety assessment area, responses of a containment building were monitored and the analysis method was verified. Also performed are the identification of earthquake characteristics and improvement of the seismic fragility analysis method. In the area of aging assessment of a containment building, we developed aging management code SLMS and database. Aging tests were performed for containment building materials and aging models were developed. Techniques for investigation, detection, and evaluation of aging were developed. In the area of prediction of long-term behavior and analysis of a containment building, we developed a non-linear structural analysis code NUCAS and material models. In the area of performance verification of a containment building, we analyzed the crack behavior of a containment wall and the behavior of the containment under internal pressure. We also improved the ISI methods for prestressed containment

Code of practice for ionizing radiation

International Nuclear Information System (INIS)

Khoo Boo Huat

1995-01-01

Prior to 1984, the use of ionizing radiation in Malaysia was governed by the Radioactive Substances Act of 1968. After 1984, its use came under the control of Act 304, called the Atomic Energy Licensing Act 1984. Under powers vested by the Act, the Radiation Protection (Basic Safety Standards) Regulations 1988 were formulated to regulate its use. These Acts do not provide information on proper working procedures. With the publication of the codes of Practice by The Standards and Industrial Research Institute of Malaysia (SIRIM), the users are now able to follow proper guidelines and use ionizing radiation safely and beneficially. This paper discusses the relevant sections in the following codes: 1. Code of Practice for Radiation Protection (Medical X-ray Diagnosis) MS 838:1983. 2. Code of Practice for Safety in Laboratories Part 4: Ionizing radiation MS 1042: Part 4: 1992. (author)

Non-binary Hybrid LDPC Codes: Structure, Decoding and Optimization

OpenAIRE

Sassatelli, Lucile; Declercq, David

2007-01-01

In this paper, we propose to study and optimize a very general class of LDPC codes whose variable nodes belong to finite sets with different orders. We named this class of codes Hybrid LDPC codes. Although efficient optimization techniques exist for binary LDPC codes and more recently for non-binary LDPC codes, they both exhibit drawbacks due to different reasons. Our goal is to capitalize on the advantages of both families by building codes with binary (or small finite set order) and non-bin...

Considering soil-structure interaction effects in the equivalent static analysis method of the Iranian of the Iranian seismic building code

International Nuclear Information System (INIS)

Shakib, H.; Dehghani Ashkezari, G.

2002-01-01

In this study, based on the equivalent static analysis method of the Iranian seismic code, an algorithm is presented to consider the soil-structure interaction (SSI) effects. Modifications of free field motion and structural properties like period and damping due to soil situation are considered in the proposed algorithm. An increase for fundamental period of structure and a modification (usually increase) for it's effective damping are observed. The increase of period is due to the flexibility of the soil foundation and modification of damping is due to the dissipating energy in soil. In order to propose the relative expressions in the presented algorithm, the soil-structure analyses of 8, 10, 13 and 16 stories frames are carried out. By considering the NEHRP soil-structure interaction algorithm and findings of soil-structure interaction analyses carried out in this study, the algorithm based on the equivalent static analysis method of the Iranian seismic building code to consider the effect of soil-structure interaction

Comparison of Standard 90.1-2007 and the 2009 IECC with Respect to Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Conover, David R.; Bartlett, Rosemarie; Halverson, Mark A.

2009-12-11

The U.S. Department of Energy’s (DOE’s) Building Energy Codes Program (BECP) has been asked by some states and energy code stakeholders to address the comparability of the 2009 International Energy Conservation Code® (IECC) as applied to commercial buildings and ANSI/ASHRAE/IESNA Standard 90.1-2007 (hereinafter referred to as Standard 90.1-07). An assessment of comparability will help states respond to and implement conditions specified in the State Energy Program (SEP) Formula Grants American Recovery and Reinvestment Act Funding Opportunity, Number DE-FOA-0000052, and eliminate the need for the states individually or collectively to perform comparative studies of the 2009 IECC and Standard 90.1-07. The funding opportunity announcement contains the following conditions: (2) The State, or the applicable units of local government that have authority to adopt building codes, will implement the following: (A) A residential building energy code (or codes) that meets or exceeds the most recent International Energy Conservation Code, or achieves equivalent or greater energy savings. (B) A commercial building energy code (or codes) throughout the State that meets or exceeds the ANSI/ASHRAE/IESNA Standard 90.1-2007, or achieves equivalent or greater energy savings . (C) A plan to achieve 90 percent compliance with the above energy codes within eight years. This plan will include active training and enforcement programs and annual measurement of the rate of compliance. With respect to item (B) above, many more states, regardless of the edition date, directly adopt the IECC than Standard 90.1-07. This is predominately because the IECC is a model code and part of a coordinated set of model building codes that state and local government have historically adopted to regulate building design and construction. This report compares the 2009 IECC to Standard 90.1-07 with the intent of helping states address whether the adoption and application of the 2009 IECC for commercial

Can High-Performance Equipment Lead to a Low-Performance Building?

Energy Technology Data Exchange (ETDEWEB)

Jonlin, Duane; Thornton, Brian A.; Rosenberg, Michael I.

2016-08-22

The performance-based compliance alternative available in most energy codes, intended to provide energy efficiency equivalent to that of prescriptive compliance while allowing innovation and design flexibility, can instead result in sub-standard energy performance in both the short and the long term. The potential deficiencies in modeled buildings originate with subtleties in the energy modeling rules, allowing building systems that consume more energy than their real-world, prescriptively-designed counterparts. This performance gap is exacerbated over subsequent decades as less efficient permanent features of the building remain while elements with shorter lives are regularly upgraded in most buildings. This paper summarizes an investigation into the topic for Pacific Northwest National Laboratory and the City of Seattle, including identification of the principal deficiencies exploited in the modeling path, and several potential code amendments that could resolve these deficiencies and establish better equivalency between prescriptive and performance compliance paths. The study, focusing on Seattle and Washington State energy codes, offers lessons and implications for other jurisdictions and energy codes.

Energy-efficient buildings program evaluations. Volume 1: Findings and recommendations

Energy Technology Data Exchange (ETDEWEB)

Lee, A.D.; Mayi, D.; Edgemon, S.D.

1997-04-01

This study was conducted for the US Department of Energy (DOE) by Pacific Northwest National Laboratory (PNNL). DOE operates the Building Standards and Guidelines Program (BSGP) to increase the effectiveness of building energy codes, standards, and guidelines. The main purpose of this report is to lay the groundwork for conducting an overall evaluation of the program and its effectiveness. Another purpose of this report is to summarize an extensive set of relevant evaluations and provide a building efficiency and program evaluation information resource for program designers, managers, and evaluators. This study presents information from 119 evaluations that have been conducted of both utility and code programs related to energy efficiency in new residential and commercial buildings. The authors used the information in these evaluations to identify major themes and lessons learned from utility and code programs. They also used the information to gain insights into appropriate evaluation methodologies and establish guidelines for designing future evaluations and an evaluation of the BSGP. The report presents general lessons about evaluating programs that have implications for future evaluations included the following. The evaluations provided the basis for developing an effective evaluation approach for residential building energy-efficiency codes and other energy-efficiency programs and other insights for conducting commercial building program evaluations. The findings for conducting effective evaluations are categorized by steps in the evaluation process.

The theoretical modelling of aerosol behaviour within containment buildings

International Nuclear Information System (INIS)

Dunbar, I.H.

1988-01-01

The modelling of the deposition of aerosol particles within the containment building plays an important part in determining the effectiveness of the building in reducing releases of activity following accidents. This paper describes attempts to ensure the accuracy of computer codes which model aerosol behaviour, with special reference to the code AEROSIM-M. Code intercomparisons have been used to test the reliability of the coding and the accuracy of the numerical methods. Those codes which assume that the particle size distribution is always lognormal give significantly different results from those which do not make this assumption but instead discretise the range of particle sizes. When the same physical assumptions are made, the predictions of different discrete codes are in reasonable agreement. In comparisons between an earlier version of AEROSIM and sodium fire experiments, the code achieved good agreement on the overall time-scale of deposition. An extensive set of tests of AEROSIM-M against experiments relevant to LWR conditions is underway. (author)

OPINION: Safe exponential manufacturing

Science.gov (United States)

Phoenix, Chris; Drexler, Eric

2004-08-01

In 1959, Richard Feynman pointed out that nanometre-scale machines could be built and operated, and that the precision inherent in molecular construction would make it easy to build multiple identical copies. This raised the possibility of exponential manufacturing, in which production systems could rapidly and cheaply increase their productive capacity, which in turn suggested the possibility of destructive runaway self-replication. Early proposals for artificial nanomachinery focused on small self-replicating machines, discussing their potential productivity and their potential destructiveness if abused. In the light of controversy regarding scenarios based on runaway replication (so-called 'grey goo'), a review of current thinking regarding nanotechnology-based manufacturing is in order. Nanotechnology-based fabrication can be thoroughly non-biological and inherently safe: such systems need have no ability to move about, use natural resources, or undergo incremental mutation. Moreover, self-replication is unnecessary: the development and use of highly productive systems of nanomachinery (nanofactories) need not involve the construction of autonomous self-replicating nanomachines. Accordingly, the construction of anything resembling a dangerous self-replicating nanomachine can and should be prohibited. Although advanced nanotechnologies could (with great difficulty and little incentive) be used to build such devices, other concerns present greater problems. Since weapon systems will be both easier to build and more likely to draw investment, the potential for dangerous systems is best considered in the context of military competition and arms control.

Analyses to support development of risk-informed separation distances for hydrogen codes and standards.

Energy Technology Data Exchange (ETDEWEB)

LaChance, Jeffrey L.; Houf, William G. (Sandia National Laboratories, Livermore, CA); Fluer, Inc., Paso Robels, CA; Fluer, Larry (Fluer, Inc., Paso Robels, CA); Middleton, Bobby

2009-03-01

The development of a set of safety codes and standards for hydrogen facilities is necessary to ensure they are designed and operated safely. To help ensure that a hydrogen facility meets an acceptable level of risk, code and standard development organizations are tilizing risk-informed concepts in developing hydrogen codes and standards.

Safety Case for Safe-store

International Nuclear Information System (INIS)

Woollam, Paul B.

2002-01-01

Magnox Electric plc (Magnox), a wholly owned subsidiary of BNFL, owns 26 gas-cooled, graphite-moderated units on 11 sites in the UK. Eight units have been permanently shutdown and the remainder will shut this decade in a currently declared closure programme. The first of these reactors went to power in 1952 and the fleet has generated typically 9% of the UK's electricity during the last five decades. In accordance with UK Government policy, BNFL aims for a systematic and progressive reduction in hazards on its decommissioning sites. The end-point of the decommissioning process is that the reactors will be dismantled and their sites de-licensed. This will be done through minimising both the risks to the public, workers and the environment and also the lifetime cost, consistent with world class safety. There will be passive safe storage during deferment periods and it is BNFL's clear intent that the reactors will not be Safe-stored indefinitely. The main hazard associated with any decommissioned nuclear site is the spent fuel. Hence the reactors will be de-fuelled as soon as practicable after shutdown. After this work is complete, Cs-137 contaminated plant (e.g. fuel pools, effluent plant, and drains) will be dismantled when it is no longer needed. All other plant and buildings will also be dismantled when they are no longer needed, except for the reactor buildings which will be put into passive safe storage. Co-60 contaminated plant, such as steam generators, will be dismantled with the reactors. The reactors will be dismantled in a sequenced programme, with a notional start time around 100 years from shutdown. Magnox Electric is ensuring that the reactors and primary circuits on all its sites are well characterised. We have carried out a detailed, peer reviewed hazard identification on the lead site from which we have generated a rolling 25-year basic safety case. We have then searched for cliff edge effects and possible long-term changes to generate the 100-year

Tokamak building-design considerations for a large tokamak device

International Nuclear Information System (INIS)

Barrett, R.J.; Thomson, S.L.

1981-01-01

Design and construction of a satisfactory tokamak building to support FED appears feasible. Further, a pressure vessel building does not appear necessary to meet the plant safety requirements. Some of the building functions will require safety class systems to assure reliable and safe operation. A rectangular tokamak building has been selected for FED preconceptual design which will be part of the confinement system relying on ventilation and other design features to reduce the consequences and probability of radioactivity release

Description of the COMRADEX code

International Nuclear Information System (INIS)

Spangler, G.W.; Boling, M.; Rhoades, W.A.; Willis, C.A.

1967-01-01

The COMRADEX Code is discussed briefly and instructions are provided for the use of the code. The subject code was developed for calculating doses from hypothetical power reactor accidents. It permits the user to analyze four successive levels of containment with time-varying leak rates. Filtration, cleanup, fallout and plateout in each containment shell can also be analyzed. The doses calculated include the direct gamma dose from the containment building, the internal doses to as many as 14 organs including the thyroid, bone, lung, etc. from inhaling the contaminated air, and the external gamma doses from the cloud. While further improvements are needed, such as a provision for calculating doses from fallout, rainout and washout, the present code capabilities have a wide range of applicability for reactor accident analysis

Support to the Safe Motherhood Programme in Nepal: an integrated approach.

Science.gov (United States)

Barker, Carol E; Bird, Cherry E; Pradhan, Ajit; Shakya, Ganga

2007-11-01

Evidence gathered from 1997 to 2006 indicates progress in reducing maternal mortality in Nepal, but public health services are still constrained by resource and staff shortages, especially in rural areas. The five-year Support to the Safe Motherhood Programme builds on the experience of the Nepal Safer Motherhood Project (1997-2004). It is working with the Government of Nepal to build capacity to institute a minimum package of essential maternity services, linking evidence-based policy development with health system strengthening. It has supported long-term planning, working towards skilled attendance at every birth, safe blood supplies, staff training, building management capacity, improving monitoring systems and use of process indicators, promoting dialogue between women and providers on quality of care, and increasing equity and access at district level. An incentives scheme finances transport costs to a health facility for all pregnant women and incentives to health workers attending deliveries, with free services and subsidies to facilities in the poorest 25 districts. Despite bureaucracy, frequent transfer of key government staff and political instability, there has been progress in policy development, and public health sector expenditure has increased. For the future, a human resources strategy with career paths that encourage skilled staff to stay in the government service is key.

How to Build MCNP 6.2

Energy Technology Data Exchange (ETDEWEB)

Bull, Jeffrey S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-11-13

This presentation describes how to build MCNP 6.2. MCNP®* 6.2 can be compiled on Macs, PCs, and most Linux systems. It can also be built for parallel execution using both OpenMP and Messing Passing Interface (MPI) methods. MCNP6 requires Fortran, C, and C++ compilers to build the code.

The regulatory basis for site selection for radioactive buildings

International Nuclear Information System (INIS)

Sirag, N.M.

2012-01-01

The architectural bases and the design standard for radiation research buildings differ than other research building, that the nature of the used radioactive materials in the nature of the carried an work in the building will decide the planning in the design of the building, and we shall discus in this research what already had been reached of results about the architectural bases in the used standard in the used safe design of research building and establishing design standard, that archaistic rely upon when designing these project which have specific and special characters

Sub-grouping of Plasmodium falciparum 3D7 var genes based on sequence analysis of coding and non-coding regions

DEFF Research Database (Denmark)

Lavstsen, Thomas; Salanti, Ali; Jensen, Anja T R

2003-01-01

and organization of the 3D7 PfEMP1 repertoire was investigated on the basis of the complete genome sequence. METHODS: Using two tree-building methods we analysed the coding and non-coding sequences of 3D7 var and rif genes as well as var genes of other parasite strains. RESULTS: var genes can be sub...

Building confidence in decommissioning in France: Towards a safe, industrially applicable, coherent national system without site or waste liberation

International Nuclear Information System (INIS)

Averous, J.; Chapalain, E.

2002-01-01

The rate of decommissioning in France is accelerating, as the first generation of power reactors will be actively decommissioned in the next few years. Experience has been gathered from past decommissioning activities and some current pilot decommissioning operations. This experience has shown that a national system has to be put in place to deal with decommissioning, waste elimination and site cleaning up activities in order to allow a consistent, safe, transparent and industrially applicable management of these matters. A system founded on successive lines of defence has been put into enforcement, which does not involve any site nor waste liberation, as it is considered that the criteria associated are always prone to discussion and contradiction. This system is based on the following concepts : 'nuclear waste', waste prone to have been contaminated or activated, is segregated from 'conventional waste' using a system involving successive lines of defence, and hence, building a very high level of confidence that no 'nuclear waste' will be eliminated without control in conventional waste eliminators or recycling facilities ; 'nuclear waste' is eliminated in dedicated facilities or repositories, or in conventional facilities under the condition of a special authorisation based on a radiological impact study and a public inquiry ; a global safety evaluation of the nuclear site is conducted after decommissioning in order to define possible use restrictions. In all cases, minimum restrictions will be put into enforcement in urbanisation plans to ensure sufficient precaution when planning future uses of the ground or the building. This paper describes this global system in detail and shows that its inherent consistency allows it to be easily applicable by operators while achieving a high level of safety and confidence. (author)

Development of 3D models of buildings for containment of the nuclear power plant of Almaraz and of the Trillo Nuclear with the GOTHIC 8.0 code

International Nuclear Information System (INIS)

Jimenez, G.; Bocanegra Melian, R.; Fernandez Cosils, K.; Barreira Pereira, P.; Rey Peinado, L.; Posada Barral, J. M.

2014-01-01

The objective of the first phase of the research of CNAT and the UPM project is the construction of several three-dimensional models detailed GOTHIC 8.0 code of containment of a buildings plant type PWR-W and KWU, corresponding to the Central Nuclear de Almaraz (CNA) and Trillo (CNT) respectively. (Author)

Building world-wide nuclear industry success stories - Safe management of nuclear waste and used nuclear fuel

International Nuclear Information System (INIS)

Saint-Pierre, S.

2005-01-01

Full text: This WNA Position Statement summarizes the worldwide nuclear industry's record, progress and plans in safely managing nuclear waste and used nuclear fuel. The global industry's safe waste management practices cover the entire nuclear fuel-cycle, from the mining of uranium to the long-term disposal of end products from nuclear power reactors. The Statement's aim is to provide, in clear and accurate terms, the nuclear industry's 'story' on a crucially important subject often clouded by misinformation. Inevitably, each country and each company employs a management strategy appropriate to a specific national and technical context. This Position Statement reflects a confident industry consensus that a common dedication to sound practices throughout the nuclear industry worldwide is continuing to enhance an already robust global record of safe management of nuclear waste and used nuclear fuel. This text focuses solely on modern civil programmes of nuclear-electricity generation. It does not deal with the substantial quantities of waste from military or early civil nuclear programmes. These wastes fall into the category of 'legacy activities' and are generally accepted as a responsibility of national governments. The clean-up of wastes resulting from 'legacy activities' should not be confused with the limited volume of end products that are routinely produced and safely managed by today's nuclear energy industry. On the significant subject of 'Decommissioning of Nuclear Facilities', which is integral to modern civil nuclear power programmes, the WNA will offer a separate Position Statement covering the industry's safe management of nuclear waste in this context. The safe management of nuclear waste and used nuclear fuel is a widespread, well-demonstrated reality. This strong safety record reflects a high degree of nuclear industry expertise and of industry responsibility toward the well-being of current and future generations. Accumulating experience and

Comparative Policy Study for Green Buildings in U.S. and China

Energy Technology Data Exchange (ETDEWEB)

Khanna, Nina; Romankiewicz, John; Feng, Wei; Zhou, Nan; Ye, Qing

2014-04-01

Prominent barriers facing the U.S. green building industry include the fact that government bodies that supervise health, fire safety, land, and other public operations are slow to revise codes to accommodate green building (regulatory barrier). In China, the lack of a green building professional accreditation process similar to the Leadership in Energy and Environmental Design (LEED) AP process limits the green building workforce capacity development (informational barrier). The main policies highlighted in this report to tackle these barriers are 1) comprehensive codes and labeling plan (informational, institutional), 2) government-led targets and demonstrations (risk), 3) education and awareness programs (informational), 4) fiscal policy that supports green building investment (financial), and 5) integrated design promotion (institutional, financial).

Energy Building Regulations: The Effect of the Federal Performance Standards on Building Code Administration and the Conservation of Energy in New Buildings.

Science.gov (United States)

Kopper, William D.

1980-01-01

Explores the changes in the administration and enforcement of building regulations that will be engendered by the proposed federal energy building standards. Also evaluates the effectiveness of those standards in meeting congressional intent. Available from U.C. Davis Law Review, School of Law, Martin Luther King Jr. Hall, University of…

Photovoltaics for Buildings Cutting-Edge PV

International Nuclear Information System (INIS)

Hayter, S. J.; Martin, R. L.

1998-01-01

Photovoltaic (PV) technology development for building-integrated applications (commonly called PV for Buildings) is one of the fastest growing areas in the PV industry. Buildings represent a huge potential market for photovoltaics because they consume approximately two-thirds of the electricity consumed in the US. The PV and buildings industries are beginning to work together to address issues including building codes and standards, integration, after-market servicing, education, and building energy efficiency. One of the most notable programs to encourage development of new PV-for-buildings products is the PV:BONUS program, supported by the US Department of Energy. Demand for these products from building designers has escalated since the program was initiated in 1993. This paper presents a range of PV-for-buildings issues and products that are currently influencing today's PV and buildings markets

Superficiary Right of Building: Origin and Development in Central Europe

Directory of Open Access Journals (Sweden)

Petr Pavel

2016-06-01

Full Text Available The Czech Republic has been dealing for the last four years with a legal revolution in the field of private law. A new Civil Code was adopted in 2012 and many new and forgotten legal figures were restored in the text of the code. An interesting example of forgotten legal figures is the superficiary right of building, which has again entered the legal order of the Czech Republic after a long one hundred years. Unlike the Act on the Superficiary Right of Building of 1912, the new Civil Code extends the scope of persons that may create the superficiary right of building to their land. This should eliminate the obstacle that has substantially limited its wider use. The superficiary right of building is not likely to become a legal concept very frequently seen in public registers. The aim of this paper is, therefore, a reflection on divided ownership and the purpose and genesis of the superficiary right of building in relation to its origins, as well as a prediction of future developments of this legal concept in the real estate market. To analyse the concept, the paper employs formal and legal methods (logical, grammatical and historical method. A comparative study is conducted in the spirit of the comparative method. The superficiary right of building is a suitable complement to the range of options of property rights offered by the new Civil Code. The author concludes that the use of the superficiary right of building, although not limited in comparison with the 1912 Act, will likely be less frequent and focused on longer-term projects.

Evacuation routes performances and fire safety of buildings

Directory of Open Access Journals (Sweden)

Laban Mirjana Đ.

2015-01-01

Full Text Available Residential buildings, public and business facilities with large number of occupants are particularly exposed to the risk of event with catastrophic consequences, especially in case of fire. Evacuation routes must be separated fire compartments with surfaces made of non-combustible materials. Safe evacuation of building occupants in case of fire is a crucial requirement for the preservation of human life in building. In our engineering practice, calculation model is usually applied in order to determine the time required for evacuation (SRPS TP 21. However, evacuation simulation models are more present in research papers, contributing to better assessment of flow of evacuation in the real time. These models could provide an efficient way of testing the safety of a building in the face of fire and indicate critical points at the evacuation paths. Computer models enable the development and analysis of multiple various scenarios during a fire event, contributing to defining the measures for improving the safety of the building in case of fire. This paper analyses the fulfilment of technical requirements for the safe evacuation and proposes improvement measures based on a comparative analysis of the time required for occupants' evacuation from the building (Department of Civil Engineering and Geodesy in Novi Sad, obtained by calculation model and by using evacuation simulation software.

Building safety and human behaviour in fire: A literature review

NARCIS (Netherlands)

Kobes, M.; Helsloot, I.; de Vries, B.; Post, J.

2010-01-01

The most crucial aspect of a building's safety in the face of fire is the possibility of safe escape. An important precondition is that its fire safety facilities enable independent and adequate fire response performances by the building's occupants. In practice, it appears that the measures

Responses of a tall building with U.S. code-type instrumentation in Tokyo, Japan, to events before, during and after the Tohoku earthquake of 11 March 2011

Science.gov (United States)

Çelebi, Mehmet; Kashima, Toshihide; Ghahari, S. Farid; Abazarsa, Fariba; Taciroglu, Ertugrul

2016-01-01

The 11 March 2011 M 9.0 Tohoku earthquake generated long-duration shaking that propagated hundreds of kilometers from the epicenter and affected tall buildings in urban areas several hundred kilometers from the epicenter of the main shock. Recorded responses show that tall buildings were affected by long-period motions. This study presents the behavior and performance of a 37-story building in the Tsukuda area of Tokyo, Japan, as inferred from modal analyses of records retrieved for a time interval covering a few days before, during, and for several months after the main shock. The U.S. “code-type” array comprises three triaxial accelerometers deployed at three levels in the superstructure. Such a sparse array in a tall structure limits a reliable assessment, because its performance must be based on only the average drift ratios. Based on the inferred values of this parameter, the subject building was not structurally damaged.

Construction engineering and planning of buildings related to the EPR

International Nuclear Information System (INIS)

Kaercher, H.

1995-01-01

Among the site-independent unit buildings are the reactor building with annulus; building for safety systems with main control room; new fuel storage pit, emergency power unit, reactor auxiliaries, access building; conventional switchgear building, and the turbine building. All buildings housing safety-related systems are protected against external and internal influences. Among the design-determining external influences are earthquakes, explosion high-pressure wave and aircraft crash. Internal incidents are caused by failure of components and pipes. The most discussed incident in the connection is the failure of the reactor pressure vessel involving core melt release which is safely retained by special devices. Earlier 3D plant models made of plastic have been replaced by 3D CAE computer models. Thus the graphic data of CAD systems have been added to the immense amount of logistic programmes/process data chains. This leads to new planning tools which are able to safely process such amounts of data and at the same time notably reduce planning time and expense. The whole data processing concept is characterized by simple, consistent data structures according to a uniform data model. It enables continual treatment throughout all planning stages and data exchange through simple, uniformly structured interfaces. (orig./HP) [de

CONTRANS 2 code conversion from Apollo to HP

International Nuclear Information System (INIS)

Lee, Hae Cho

1996-01-01

CONTRANS2 computer code is used to calculate transient thermal hydraulic responses of containment building to loss of coolant and main steam line break accident. Mass and energy release to the containment following an accident are code inputs. This report firstly describes detailed work carried out for installation of CONTRANS2 on Apollo DN10000 and code validation results after installation. Secondly, A series of work is also describes in relation to installation of CONTRANS2 on HP 9000/700 series as well as relevant code validation results. Attached is a report on software verification and validation results. 7 refs. (Author) .new

Numerical simulation of solar heating of buildings. Final report

Energy Technology Data Exchange (ETDEWEB)

Coffe, G.; Jannot, M.; Pellerin, J.F.

1980-01-01

This study is divided into two parts: First, the thermal modelling of a solar + electric heated building is presented; mathematical equations are established; numerical calculations are analyzed; and a calculation code in FORTRAN V is set down. Second, this calculation code was used to study the thermal performances of the solar + electric heated building in three European climates: Copenhagen (56/sup 0/ north latitude - Denmark), Trappes (48/sup 0/ north latitude - France), and Carpentras (44/sup 0/ north latitude - France).

Energy conservation according to the building codes of the National Board of Housing, Building and Planning; Energihushaallning enligt Boverkets byggregler

Energy Technology Data Exchange (ETDEWEB)

2009-10-15

To comply with international and national targets for energy use, the National Board has adopted rules setting the levels to be met in order to conserve energy in buildings. The rules for buildings are shown in Boverkets building regulations (BBR). The BBR lists comprehensive requirements in order to ensure that a building must not use more than a certain number of kilowatt hours per square meter and year. There are more detailed requirements for thermal insulation, heating, cooling and air conditioning installations, efficient use of electricity and installation of metering systems for monitoring of building energy. The latest version of the BBR came into force on February 1, 2009 and has more stringent requirements for the buildings heated by electricity or comfort cooling powered by electricity. This handbook presents comments and answers to questions about the new rules for energy conservation. It replaces our previous handbook 'Thermal calculations'

Safe Handling of Radioisotopes. 1973 Edition

International Nuclear Information System (INIS)

1973-01-01

Under its Statute the International Atomic Energy Agency is empowered to provide for the application of standards of safety for protection against radiation to its own operations and to operations making use of assistance provided by it or with which it is otherwise directly associated. To this end authorities receiving such assistance are required to observe relevant health and safety measures prescribed by the Agency. As a first step, it was considered an urgent task to provide users of radionuclides with a manual of practice for the safe handling of these substances. The first edition of such a manual was published in 1958 and represented the first of the ''Safety Series'', a series of manuals and codes on health and safety published by the Agency. It was prepared after careful consideration of existing national and international codes of radiation safety by a group of international experts and in consultation with other international bodies. This edition presents the second revision. In response to the suggestion made by some Member States, the term 'radioisotopes' has been changed to 'radionuclides' in the title and, as appropriate, in the text because the term 'radionuclides' includes the radioactive element itself as well as the isotopes. The series of manuals and codes published in the Safety Series and the Technical Reports Series give more complete advice to the user on specialized topics.

DQO Summary Report for 105-N/109-N Interim Safe Storage Project Waste Characterization

Energy Technology Data Exchange (ETDEWEB)

T. A. Lee

2005-09-15

The DQO summary report provides the results of the DQO process completed for waste characterization activities for the 105-N/109-N Reactor Interim Safe Storage Project including decommission, deactivate, decontaminate, and demolish activities for six associated buildings.

DQO Summary Report for 105-N/109-N Interim Safe Storage Project Waste Characterization

International Nuclear Information System (INIS)

Lee, T.A.

2005-01-01

The DQO summary report provides the results of the DQO process completed for waste characterization activities for the 105-N/109-N Reactor Interim Safe Storage Project including decommission, deactivate, decontaminate, and demolish activities for six associated buildings.

Development of 'SKYSHINE-CG' code. A line-beam method code equipped with combinatorial geometry routine

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, Takahiro; Ochiai, Katsuharu [Plant and System Planning Department, Toshiba Corporation, Yokohama, Kanagawa (Japan); Uematsu, Mikio; Hayashida, Yoshihisa [Department of Nuclear Engineering, Toshiba Engineering Corporation, Yokohama, Kanagawa (Japan)

2000-03-01

A boiling water reactor (BWR) plant has a single loop coolant system, in which main steam generated in the reactor core proceeds directly into turbines. Consequently, radioactive {sup 16}N (6.2 MeV photon emitter) contained in the steam contributes to gamma-ray skyshine dose in the vicinity of the BWR plant. The skyshine dose analysis is generally performed with the line-beam method code SKYSHINE, in which calculational geometry consists of a rectangular turbine building and a set of isotropic point sources corresponding to an actual distribution of {sup 16}N sources. For the purpose of upgrading calculational accuracy, the SKYSHINE-CG code has been developed by incorporating the combinatorial geometry (CG) routine into the SKYSHINE code, so that shielding effect of in-building equipment can be properly considered using a three-dimensional model composed of boxes, cylinders, spheres, etc. Skyshine dose rate around a 500 MWe BWR plant was calculated with both SKYSHINE and SKYSHINE-CG codes, and the calculated results were compared with measured data obtained with a NaI(Tl) scintillation detector. The C/E values for SKYSHINE-CG calculation were scattered around 4.0, whereas the ones for SKYSHINE calculation were as large as 6.0. Calculational error was found to be reduced by adopting three-dimensional model based on the combinatorial geometry method. (author)

Operating nuclear plant feedback to ASME and French codes

International Nuclear Information System (INIS)

Journet, J.; O'Donnell, W.J.

1996-01-01

The French have an advantage in nuclear plant operating experience feedback due to the highly centralized nature of their nuclear industry. There is only one utility in charge of design as well as operations (EDF) and only one reactor vendor (Framatome). The ASME Code has played a key role in resolving technical issues in the design and operation of nuclear plants since the inception of nuclear power. The committee structure of the Code brings an ideal combination of senior technical people with both broad and specialized experience to bear on complex how safe is safe enough technical issues. The authors now see an even greater role for the ASME Code in a proposed new regulatory era for the US nuclear industry. The current legalistic confrontational regulatory era has been quite destructive. There now appears to be a real opportunity to begin a new era of technical consensus as the primary means for resolving safety issues. This change can quickly be brought about by having the industry take operating plant problems and regulatory technical issues directly to the ASME Code for timely resolution. Surprisingly, there is no institution in the US nuclear industry with such a mandate. In fact, the industry is organized to feedback through the Nuclear Regulatory Commission issues which could be far better resolved through the ASME Code. Major regulatory benefits can be achieved by closing this loop and providing systematic interaction with the ASME Code. The essential elements of a new regulatory era and ideas for organizing US institutional industry responsibilities, taken from the French experience, are described in this paper

Assessment Framework of Building Facade in Optimizing Indoor Thermal Comfort of Green Building Index (GBI Certified Office Building

Directory of Open Access Journals (Sweden)

Abdul Tharim Asniza Hamimi

2016-01-01

Full Text Available During the past decade, the construction industry has seen a new trend in the development of “green” or “sustainable” construction concept around the world with vast support from prominent organization, together with the introduction of sustainable building codes. The establishment of green building certification systems worldwide is seen as one of the most efforts in the emerging green building movement. In order to support the development of the “green” and “sustainable” concept in Malaysia, Green Building Index (GBI was launched by the government on 21 May 2009 that created to promote sustainability in the built environment and raise awareness of environmental issues. However, the construction industry seems to have focused only on findings the “right mechanism” for an environmentally sustainable “final result” in order for the building to be certified as green with the lacking of continuous assessment on the building performance after the certifications. This study is purposely conducted to investigate the performance of various rated Green Building Index (GBI Non-Residential New Construction office buildings and the influence on Indoor Thermal Comfort (ITC of the selected buildings. The aim is to develop an assessment framework for optimum green building architectural façade to be used for office buildings in Malaysia as well as to analyse the occupants’ perception, satisfaction and performance in the selected Green Building Index (GBI rated office indoor environment. This research is still in its infancy; therefore the paper is focused on research aims, research scope and methodology, and expected deliverables for the proposed research.

Preliminary Validation of the MATRA-LMR Code Using Existing Sodium-Cooled Experimental Data

International Nuclear Information System (INIS)

Choi, Sun Rock; Kim, Sangji

2014-01-01

The main objective of the SFR prototype plant is to verify TRU metal fuel performance, reactor operation, and transmutation ability of high-level wastes. The core thermal-hydraulic design is used to ensure the safe fuel performance during the whole plant operation. The fuel design limit is highly dependent on both the maximum cladding temperature and the uncertainties of the design parameters. Therefore, an accurate temperature calculation in each subassembly is highly important to assure a safe and reliable operation of the reactor systems. The current core thermalhydraulic design is mainly performed using the SLTHEN (Steady-State LMR Thermal-Hydraulic Analysis Code Based on ENERGY Model) code, which has been already validated using the existing sodium-cooled experimental data. In addition to the SLTHEN code, a detailed analysis is performed using the MATRA-LMR (Multichannel Analyzer for Transient and steady-state in Rod Array-Liquid Metal Reactor) code. In this work, the MATRA-LMR code is validated for a single subassembly evaluation using the previous experimental data. The MATRA-LMR code has been validated using existing sodium-cooled experimental data. The results demonstrate that the design code appropriately predicts the temperature distributions compared with the experimental values. Major differences are observed in the experiments with the large pin number due to the radial-wise mixing difference

Building and Testing with Gradle

CERN Document Server

Berglund, Tim

2011-01-01

Build and test software written in Java and many other languages with Gradle, the open source project automation tool that's getting a lot of attention. This concise introduction provides numerous code examples to help you explore Gradle, both as a build tool and as a complete solution for automating the compilation, test, and release process of simple and enterprise-level applications. Discover how Gradle improves on the best ideas of Ant, Maven, and other build tools, with standards for developers who want them and lots of flexibility for those who prefer less structure. Use Gradle with Gr

Guidance notes : safe practice for the use of nuclear density meters

International Nuclear Information System (INIS)

2000-06-01

These 'Guidance notes' have been written to provide information for owners and users on the safe care and use of instruments containing radioactive materials used for the measurement of moisture content and/or density of materials. They give practical guidance on compliance with the requirements of radiation protection legislation and the 'Code of safe practice for the use of nuclear density meters, NRL C15'. Some of these instruments have been known as 'soil moisture gauges' and others as 'nuclear density meters' or just 'NDMs'. For simplicity, these 'Guidance notes' will follow industry terminology and use the term 'nuclear density meter'. Some parts of these 'Guidance notes' and of the 'Code, NRL C15' are relevant for users of asphalt gauges containing radioactive sources. These are normally laboratory bench instruments, and are not portable field instruments. Nevertheless, the radioactive sources used are similar to those used for moisture measurement and the safety implications are similar. The units of measurement of radioactivity and radiation dose are discussed in Appendix 1. Appendix 2 contains consent application forms while sample transport forms can be found in Appendix 3. (author). 10 refs

Analysis of the Chinese Market for Building Energy Efficiency

Energy Technology Data Exchange (ETDEWEB)

Yu, Sha [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Evans, Meredydd [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shi, Qing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-03-20

China will account for about half of the new construction globally in the coming decade. Its floorspace doubled from 1996 to 2011, and Chinese rural buildings alone have as much floorspace as all of U.S. residential buildings. Building energy consumption has also grown, increasing by over 40% since 1990. To curb building energy demand, the Chinese government has launched a series of policies and programs. Combined, this growth in buildings and renovations, along with the policies to promote green buildings, are creating a large market for energy efficiency products and services. This report assesses the impact of China’s policies on building energy efficiency and on the market for energy efficiency in the future. The first chapter of this report introduces the trends in China, drawing on both historical analysis, and detailed modeling of the drivers behind changes in floorspace and building energy demand such as economic and population growth, urbanization, policy. The analysis describes the trends by region, building type and energy service. The second chapter discusses China’s policies to promote green buildings. China began developing building energy codes in the 1980s. Over time, the central government has increased the stringency of the code requirements and the extent of enforcement. The codes are mandatory in all new buildings and major renovations in China’s cities, and they have been a driving force behind the expansion of China’s markets for insulation, efficient windows, and other green building materials. China also has several other important policies to encourage efficient buildings, including the Three-Star Rating System (somewhat akin to LEED), financial incentives tied to efficiency, appliance standards, a phasing out of incandescent bulbs and promotion of efficient lighting, and several policies to encourage retrofits in existing buildings. In the third chapter, we take “deep dives” into the trends affecting key building components

Automation of Geometry Input for Building Code Compliance Check

DEFF Research Database (Denmark)

Petrova, Ekaterina Aleksandrova; Johansen, Peter Lind; Jensen, Rasmus Lund

2017-01-01

. That has left the industry in constant pursuit of possibilities for integration of the tool within the Building Information Modelling environment so that the potential provided by the latter can be harvested and the processed can be optimized. This paper presents a solution for automated data extraction...

Fuel performance analysis code 'FAIR'

International Nuclear Information System (INIS)

Swami Prasad, P.; Dutta, B.K.; Kushwaha, H.S.; Mahajan, S.C.; Kakodkar, A.

1994-01-01

For modelling nuclear reactor fuel rod behaviour of water cooled reactors under severe power maneuvering and high burnups, a mechanistic fuel performance analysis code FAIR has been developed. The code incorporates finite element based thermomechanical module, physically based fission gas release module and relevant models for modelling fuel related phenomena, such as, pellet cracking, densification and swelling, radial flux redistribution across the pellet due to the build up of plutonium near the pellet surface, pellet clad mechanical interaction/stress corrosion cracking (PCMI/SSC) failure of sheath etc. The code follows the established principles of fuel rod analysis programmes, such as coupling of thermal and mechanical solutions along with the fission gas release calculations, analysing different axial segments of fuel rod simultaneously, providing means for performing local analysis such as clad ridging analysis etc. The modular nature of the code offers flexibility in affecting modifications easily to the code for modelling MOX fuels and thorium based fuels. For performing analysis of fuel rods subjected to very long power histories within a reasonable amount of time, the code has been parallelised and is commissioned on the ANUPAM parallel processing system developed at Bhabha Atomic Research Centre (BARC). (author). 37 refs

FIRE EVACUATION FROM HIGH-RISE BUILDINGS

Directory of Open Access Journals (Sweden)

Korol'chenko Aleksandr Yakovlevich

2012-10-01

Full Text Available The authors argue that no collapse of structures is likely in the event of a fire emergency in multistoried buildings, rather, other fire-related factors may endanger the lives of people inside high-rise buildings exposed to the fire emergency, including open fire, sparks, high ambient temperature, smoke and toxic combustion products, reduced concentration of oxygen, and combined influence of various factors. In case of fire, the temperature inside buildings reaches 1100 °С. It exceeds the temperature of the ambient air acceptable for humans by far (70 °С. The experiments demonstrate that combustion products contain hundreds of toxic chemical compounds. The most hazardous of them include carbon oxide, carbon dioxide, chloride and cyanic hydrogen, aldehydes and acrolein. The author provides the pattern of their influence on the human body. The smoke consists of unburned particles of carbon and aerosols. The size of particles fluctuates within 0.05-50 MMK. Smoke produces a physiological and psychological impact on human beings. It has been proven that dangerous fire factors emerge within the first five to ten minutes of the emergency situation. Evacuation is the principal method of safety assurance. However, the velocity of propagation of smoke and heat is so high that even if the fire prevention system is in operation, people may be blocked both on the floors that are exposed to the fire and those that escape its propagation. New evacuation and rescue methods are recommended by the author. Various ways and methods of use of life-saving facilities are also provided. Safe evacuation is feasible from buildings where the number of stories does not exceed 10- 12. During evacuation, high density human streams are formed inside buildings, therefore, the period of stay in a burning building is increased. The calculations have proven that a two-minute delay of evacuation converts into a safe evacuation of only 13-15% of people. Low reliability of

Progress towards the specification of embodied energy performance criteria for New Zealand buildings

Energy Technology Data Exchange (ETDEWEB)

Baird, G.; Alcorn, A.; Wood, P.; Storey, J. B. [Victoria Univ., Wellington (New Zealand). School of Architecture; Jaques, R. [Building Research Association of New Zealand, Inc. (New Zealand)

1998-11-01

Incorporation of embodied energy performance criteria into New Zealand`s recently adopted performance-based building code is discussed. The paper also describes the concept of the Building Code and its energy related clauses and standards, work done to date to update the building materials` energy coefficients, and the progress made in using an embodied energy database. The purpose, desirability and likely pitfalls of such criteria, ways of specifying minimum performance, and relationships with operating energy criteria are also reviewed.

2013 Building Technologies Office Program Peer Review Report

Energy Technology Data Exchange (ETDEWEB)

none,

2013-11-01

The 2013 Building Technologies Office Program Peer Review Report summarizes the results of the 2013 Building Technologies Office (BTO) peer review, which was held in Washington, D.C., on April 2–4, 2013. The review was attended by over 300 participants and included presentations on 59 BTO-funded projects: 29 from BTO’s Emerging Technologies Program, 20 from the Commercial Buildings Integration Program, 6 from the Residential Buildings Integration Program, and 4 from the Building Energy Codes Program. This report summarizes the scores and comments provided by the independent reviewers for each project.

77 FR 26647 - National Building Safety Month, 2012

Science.gov (United States)

2012-05-04

... implementing state-of-the-art building safety, energy efficiency, and fire prevention codes and standards, they... our Nation's ability to withstand the threats and hazards we face. My Administration is committed to... disasters. We are drawing upon cutting edge science and technology to establish stronger codes and standards...

The Pennsylvania State University Light Water Ultra-Safe Plant Concept: 3rd quarter progress report

International Nuclear Information System (INIS)

Klevans, E.

1987-01-01

Progress in the Ultra Safe study has substantially increased since the last report. The search for pressurizing pump turbine component information is now complete and a final plant layout for detailed evaluation has been chosen. Significant results for the normal operation performance of the Ultra Safe pressurizing technique are included. The plan of attack for the evaluation of the Ultra Safe shutdown scenario and natural circulation capability is discussed. This process is expected to be the next key area for analysis. The reactor design is complete including a change to alleviate the need for a soluble boron system. Material on the reactor building layout is also provided

Regulatory control for safe usage of radiation sources in India

International Nuclear Information System (INIS)

Ghosh, P.K.; Sonawane, A.U.

1998-01-01

The widespread applications of radioactive materials and radiation generating equipment in the field of industry, medicine agriculture and research in India necessitated the establishment of an efficient regulatory framework and consequently the Atomic Energy Regulatory Board (AERB) was constituted to exercise regulatory control over the safe usage of the radioactive materials and the radiation generating equipment. The Atomic Energy Act, 1962 and the Radiation Protection Rules, 1971 promulgated under the Act forms the basis of radiation safety in India and Chairman, AERB is the Competent Authority to enforce the regulatory provisions of the Radiation Protection Rules, 1971, for safe use of radiation source in the country. AERB has published a number of documents such as Radiation Surveillance Procedures, Standards, Codes, Guides and Manuals for safe use and handling of radioactive materials and radiation generating equipment. Apart from nuclear fuel cycle documents, these publications pertain to industrial radiography, medical application of radiation, transport of radioactive material, industrial gamma irradiators, X-ray units etc. AERB safety related publications are based on international standards e.g. BSS, IAEA, ICRP, ISO etc. This paper outlines the methodology of regulatory control exercised by AERB for safe use of the radioactive materials and the radiation generating equipment in the country. (author)

76 FR 12719 - Safe Schools/Healthy Students Program; Office of Safe and Drug-Free Schools; Safe Schools/Healthy...

Science.gov (United States)

2011-03-08

... DEPARTMENT OF EDUCATION Safe Schools/Healthy Students Program; Office of Safe and Drug- Free Schools; Safe Schools/Healthy Students Program; Catalog of Federal Domestic Assistance (CFDA) Numbers: 84... priorities, requirements, and definitions under the Safe Schools/Healthy Students (SS/HS) program. Since...

Impact of coupled heat and moisture transfer effects on buildings energy consuption

Directory of Open Access Journals (Sweden)

Ferroukhi Mohammed Yacine

2017-01-01

Full Text Available Coupled heat, air, and moisture transfers through building envelope have an important effect on prediction of building energy requirements. Several works were conducted in order to integrate hygrothermal transfers in dynamic buildings simulations codes. However, the incorporation of multidirectional hygrothermal transfer analysis in the envelope into building simulation tools is rarely considered. In this work, coupled heat, air, and moisture (HAM transfer model in multilayer walls was established. Thereafter, the HAM model is coupled dynamically to a building behavior code (BES.The coupling concerns a co-simulation between COMSOL Multiphysics and TRNSYS software. Afterward, the HAM-BES co-simulation accuracy was verified. Then, HAM-BES co-simulation platform was applied to a case study with various types of climates (temperate, hot and humid, cold and humid. Three simulations cases were carried out. The first simulation case consists of the TRNSYS model without HAM transfer model. The second simulation case, 1-D HAM model for the envelope was integrated in TRNSYS code. For the third one, 1-D HAM model for the wall and 2-D HAM model for thermal bridges were coupled to the thermal building model of TRNSYS. Analysis of the results confirms the significant impact of 2-D envelope hygrothermal transfers on the indoor thermal and moisture behavior of building as well as on the energy building assessment. These conclusions are shown for different studied climates.

Two-Point Codes for the Generalised GK curve

DEFF Research Database (Denmark)

Barelli, Élise; Beelen, Peter; Datta, Mrinmoy

2017-01-01

completely cover and in many cases improve on their results, using different techniques, while also supporting any GGK curve. Our method builds on the order bound for AG codes: to enable this, we study certain Weierstrass semigroups. This allows an efficient algorithm for computing our improved bounds. We......We improve previously known lower bounds for the minimum distance of certain two-point AG codes constructed using a Generalized Giulietti–Korchmaros curve (GGK). Castellanos and Tizziotti recently described such bounds for two-point codes coming from the Giulietti–Korchmaros curve (GK). Our results...

Thermal comfort in residential buildings: Comfort values and scales for building energy simulation

Energy Technology Data Exchange (ETDEWEB)

Peeters, Leen; D' haeseleer, William [Division of Applied Mechanics and Energy Conversion, University of Leuven (K.U.Leuven), Celestijnenlaan 300 A, B-3001 Leuven (Belgium); Dear, Richard de [Division of Environmental and Life Sciences, Macquarie University, Sydney (Australia); Hensen, Jan [Faculty of Architecture, Building and Planning, Technische Universiteit Eindhoven, Vertigo 6.18, P.O. Box 513, 5600 MB Eindhoven (Netherlands)

2009-05-15

Building Energy Simulation (BES) programmes often use conventional thermal comfort theories to make decisions, whilst recent research in the field of thermal comfort clearly shows that important effects are not incorporated. The conventional theories of thermal comfort were set up based on steady state laboratory experiments. This, however, is not representing the real situation in buildings, especially not when focusing on residential buildings. Therefore, in present analysis, recent reviews and adaptations are considered to extract acceptable temperature ranges and comfort scales. They will be defined in an algorithm, easily implementable in any BES code. The focus is on comfortable temperature levels in the room, more than on the detailed temperature distribution within that room. (author)

Multi-Year Program Plan - Building Regulatory Programs

Energy Technology Data Exchange (ETDEWEB)

none,

2010-10-01

This document presents DOE’s multi-year plan for the three components of the Buildings Regulatory Program: Appliance and Equipment Efficiency Standards, ENERGY STAR, and the Building Energy Codes Program. This document summarizes the history of these programs, the mission and goals of the programs, pertinent statutory requirements, and DOE’s 5-year plan for moving forward.

Active Fault Near-Source Zones Within and Bordering the State of California for the 1997 Uniform Building Code

Science.gov (United States)

Petersen, M.D.; Toppozada, Tousson R.; Cao, T.; Cramer, C.H.; Reichle, M.S.; Bryant, W.A.

2000-01-01

The fault sources in the Project 97 probabilistic seismic hazard maps for the state of California were used to construct maps for defining near-source seismic coefficients, Na and Nv, incorporated in the 1997 Uniform Building Code (ICBO 1997). The near-source factors are based on the distance from a known active fault that is classified as either Type A or Type B. To determine the near-source factor, four pieces of geologic information are required: (1) recognizing a fault and determining whether or not the fault has been active during the Holocene, (2) identifying the location of the fault at or beneath the ground surface, (3) estimating the slip rate of the fault, and (4) estimating the maximum earthquake magnitude for each fault segment. This paper describes the information used to produce the fault classifications and distances.

Lightning protection system analysis at Multipurpose Reactor G A. Siwabessy building

International Nuclear Information System (INIS)

Teguh-Sulistyo

2003-01-01

Analysis to the part of lightning protection system at Multi Purpose Reactor GA Siwabessy (RSG-GAS) have been done. Observation examined the damage of some part of the earthing system caused by human error of chemically system. The analysis performed some assumptions and simulations to the points of lightning stroke. From this analysis obtained that the reactor building do not have vertical finial which can protect effectively to the whole reactor building and auxiliary building. Installing some new finials at some places are needed to protect building therefore the reactor building and auxiliary building well safe from lighting stroke

Relevant documents to IAEA regulations for the safe transport of radioactive materials

International Nuclear Information System (INIS)

El-Shinawy, R.M.K.; Sabek, M.G.; Gomma, M.

1998-01-01

IAEA regulations for the safe transport of radioactive materials provide standards for insuring a high level of safety of people, property, and environment against radiation, contamination, and criticality hazards as well as thermal effects associated with the transport of radioactive materials. IAEA routinely publishes technical reports which are relevant to radioactive material transportation such as INTERTRAN, directory of transport packaging test facilities, and others. A case study was performed to assess the impact of transporting radioactive materials through the suez canal using the two computer codes namely INTERTRAN and RADTRAN-4 which are part of IAEA technical documents. A comparison of the results of these two codes is given

Flood-resilient waterfront development in New York City: bridging flood insurance, building codes, and flood zoning.

Science.gov (United States)

Aerts, Jeroen C J H; Botzen, W J Wouter

2011-06-01

Waterfronts are attractive areas for many-often competing-uses in New York City (NYC) and are seen as multifunctional locations for economic, environmental, and social activities on the interface between land and water. The NYC waterfront plays a crucial role as a first line of flood defense and in managing flood risk and protecting the city from future climate change and sea-level rise. The city of New York has embarked on a climate adaptation program (PlaNYC) outlining the policies needed to anticipate the impacts of climate change. As part of this policy, the Department of City Planning has recently prepared Vision 2020: New York City Comprehensive Waterfront Plan for the over 500 miles of NYC waterfront (NYC-DCP, 2011). An integral part of the vision is to improve resilience to climate change and sea-level rise. This study seeks to provide guidance for advancing the goals of NYC Vision 2020 by assessing how flood insurance, flood zoning, and building code policies can contribute to waterfront development that is more resilient to climate change. © 2011 New York Academy of Sciences.

Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

International Nuclear Information System (INIS)

1984-01-01

This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

Elaboration of Safe Community Assessment System

Directory of Open Access Journals (Sweden)

Birutė Mikulskienė

2013-08-01

Full Text Available The paper aims to design an assessment system to monitor and evaluate safety parameters and administrative efforts with the purpose to increase safety in municipalities. The safety monitoring system considered is to be the most important tool for creation and development of safe communities in Lithuania. Several methods were applied to achieve this purpose. In order to determine the role of local government in ensuring the safety of people, property and environment at the local level of a meta-analysis of research reports, the Lithuanian national legislation, strategic planning documents of the state and local government were carried out. Analysis of statistical data, structural analysis, comparative analysis and synthesis methods were used while investigating the areas of safety uncertainty, risk groups, identifying safety risk factors, determining their relationship, and creating a safe community assessment system. A safe community assessment system, which consists of two types of criteria, has been elaborated. The assessment system is based on the multi-level criteria for safety monitoring and the multi-level criteria for the evaluation of municipal activities in the field of building safety. Links between the criteria, peculiarities of their application and advantages in the process of safe community creation and development are analyzed. Design and implementation of the safe community assessment system is one of the most important stages to implement the idea of safe communities. The proposed system integrates a variety of risk areas, the safety achievement criteria are linked to the criteria used in the strategic planning. Periodic assessment of the safety situation using the proposed system ensures possibility to monitor current local safety conditions and assess the changes and the trends. A safe community assessment system is proposed to be used as a tool to unified municipalities safety comprehensiveness and compare safety level in

Elaboration of Safe Community Assessment System

Directory of Open Access Journals (Sweden)

Algirdas Astrauskas

2011-12-01

Full Text Available The paper aims to design an assessment system to monitor and evaluate safety parameters and administrative efforts with the purpose to increase safety in municipalities. The safety monitoring system considered is to be the most important tool for creation anddevelopment of safe communities in Lithuania. Several methods were applied to achieve this purpose. In order to determine the role of local government in ensuring the safety of people, property and environment at the local level of a meta-analysis of research reports,the Lithuanian national legislation, strategic planning documents of the state and local government were carried out. Analysis of statistical data, structural analysis, comparative analysis and synthesis methods were used while investigating the areas of safety uncertainty, risk groups, identifying safety risk factors, determining their relationship, and creating a safe community assessment system.A safe community assessment system, which consists of two types of criteria, has been elaborated. The assessment system is based on the multi-level criteria for safety monitoring and the multi-level criteria for the evaluation of municipal activities in the field of building safety. Links between the criteria, peculiarities of their application and advantages in the process of safe community creation and development are analyzed.Design and implementation of the safe community assessment system is one of the most important stages to implement the idea of safe communities. The proposed system integrates a variety of risk areas, the safety achievement criteria are linked to the criteria used in thestrategic planning. Periodic assessment of the safety situation using the proposed system ensures possibility to monitor current local safety conditions and assess the changes and the trends. A safe community assessment system is proposed to be used as a tool to unified municipalities safety comprehensiveness and compare safety level in

Compliance Verification Paths for Residential and Commercial Energy Codes

Energy Technology Data Exchange (ETDEWEB)

Conover, David R.; Makela, Eric J.; Fannin, Jerica D.; Sullivan, Robin S.

2011-10-10

This report looks at different ways to verify energy code compliance and to ensure that the energy efficiency goals of an adopted document are achieved. Conformity assessment is the body of work that ensures compliance, including activities that can ensure residential and commercial buildings satisfy energy codes and standards. This report identifies and discusses conformity-assessment activities and provides guidance for conducting assessments.

The struggle for safe nuclear expansion in China

International Nuclear Information System (INIS)

Xu, Y.C.

2014-01-01

After a temporary halt following the Fukushima nuclear disaster in March 2011, China resumed its fast, yet cautious, expansion of nuclear energy programme. Nuclear energy is considered as part of the general strategy to deal with the challenges of energy security and climate change and to advance with ‘state of the art’ technology in its development. This article briefly discusses recent development in and driving forces behind nuclear industry in China, and several challenges it has been facing: how to adopt, adapt, standardise and indigenise whose technologies, and how to address the shortage of qualified nuclear engineers, scientists, skilled labour force and qualified regulators. More importantly, it argues that safe and secure nuclear development requires consistent policies and effective regulations. Therefore, it is crucial to build policy and regulatory capacities based on coordination, planning and management of government agencies and the industry. - Highlights: • Nuclear energy development in China. • Nuclear technology selection. • Human capital. • Regulatory regime. • Safe and secure development

Environmental assessment for the proposed CMR Building upgrades at the Los Alamos National Laboratory, Los Alamos, New Mexico. Final document

International Nuclear Information System (INIS)

1997-01-01

In order to maintain its ability to continue to conduct uninterrupted radioactive and metallurgical research in a safe, secure, and environmentally sound manner, the US Department of Energy (DOE) proposes to upgrade the Los Alamos National Laboratory (LANL) Chemistry and Metallurgy Research (CMR) Building. The building was built in the early 1950s to provide a research and experimental facility for analytical chemistry, plutonium and uranium chemistry, and metallurgy. Today, research and development activities are performed involving nuclear materials. A variety of radioactive and chemical hazards are present. The CMR Building is nearing the end of its original design life and does not meet many of today's design codes and standards. The Proposed Action for this Environmental Assessment (EA) includes structural modifications to some portions of the CMR Building which do not meet current seismic criteria for a Hazard Category 2 Facility. Also included are upgrades and improvements in building ventilation, communications, monitoring, and fire protection systems. This EA analyzes the environmental effects of construction of the proposed upgrades. The Proposed Action will have no adverse effects upon agricultural and cultural resources, wetlands and floodplains, endangered and threatened species, recreational resources, or water resources. The Proposed Action would have negligible effects on human health and transportation, and would not pose a disproportionate adverse health or environmental impact on minority or low-income populations within an 80 kilometer (50 mile) radius of the CMR Building

Environmental assessment for the proposed CMR Building upgrades at the Los Alamos National Laboratory, Los Alamos, New Mexico. Final document

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-04

In order to maintain its ability to continue to conduct uninterrupted radioactive and metallurgical research in a safe, secure, and environmentally sound manner, the US Department of Energy (DOE) proposes to upgrade the Los Alamos National Laboratory (LANL) Chemistry and Metallurgy Research (CMR) Building. The building was built in the early 1950s to provide a research and experimental facility for analytical chemistry, plutonium and uranium chemistry, and metallurgy. Today, research and development activities are performed involving nuclear materials. A variety of radioactive and chemical hazards are present. The CMR Building is nearing the end of its original design life and does not meet many of today`s design codes and standards. The Proposed Action for this Environmental Assessment (EA) includes structural modifications to some portions of the CMR Building which do not meet current seismic criteria for a Hazard Category 2 Facility. Also included are upgrades and improvements in building ventilation, communications, monitoring, and fire protection systems. This EA analyzes the environmental effects of construction of the proposed upgrades. The Proposed Action will have no adverse effects upon agricultural and cultural resources, wetlands and floodplains, endangered and threatened species, recreational resources, or water resources. The Proposed Action would have negligible effects on human health and transportation, and would not pose a disproportionate adverse health or environmental impact on minority or low-income populations within an 80 kilometer (50 mile) radius of the CMR Building.

Damage assessment of mission essential buildings based on simulation studies of low yield explosives

Science.gov (United States)

Allen, Thomas G. L.

2006-04-01

There has been a lack of investigations related to low yield explosives instigated by terrorist on small but high occupancy buildings. Also, mitigating the threat of terrorist attacks against high occupancy buildings with network equipment essential to the mission of an organization is a challenging task. At the same time, it is difficult to predict how, why, and when terrorists may attack theses assets. Many factors must be considered in creating a safe building environment. Although it is possible that the dominant threat mode may change in the future, bombings have historically been a favorite tactic of terrorists. Ingredients for homemade bombs are easily obtained on the open market, as are the techniques for making bombs. Bombings are easy and quick to execute. This paper discusses the problems with and provides insights of experience gained in analyzing small scale explosions on older military base buildings. In this study, we examine the placement of various bombs on buildings using the shock wave simulation code CTH and examine the damage effects on the interior of the building, particularly the damage that is incurred on a computer center. These simulation experiments provide data on the effectiveness of a building's security and an understanding of the phenomenology of shocks as they propagate through rooms and corridors. It's purpose is to motivate researchers to take the seriousness of small yield explosives on moderately sized buildings. Visualizations from this analysis are used to understand the complex flow of the air blasts around corridors and hallways. Finally, we make suggestions for improving the mitigation of such terrorist attacks. The intent of this study is not to provide breakthrough technology, but to provide a tool and a means for analyzing the material hardness of a building and to eventually provide the incentive for more security. The information mentioned in this paper is public domain information and easily available via the

Council Adopts New AERA Code of Ethics: Ethics Committee to Emphasize Ethics Education

Science.gov (United States)

Herrington, Carolyn D.

2011-01-01

At its February 2011 meeting, the AERA Council adopted unanimously a new Code of Ethics. The Code articulates a set of standards for education researchers in education and provides principles and guidance by which they can build ethical practices in professional, scholarly, and scientific activities. The Code reflects the Association's strong…

Cool and Safe: Multiplicity in Safe Innovation at Unilever

Science.gov (United States)

Penders, Bart

2011-01-01

This article presents the making of a safe innovation: the application of ice structuring protein (ISP) in edible ices. It argues that safety is not the absence of risk but is an active accomplishment; innovations are not "made safe afterward" but "safe innovations are made". Furthermore, there are multiple safeties to be accomplished in the…

Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

Energy Technology Data Exchange (ETDEWEB)

Mertz, G.

1999-12-16

This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements.

Structural acceptance criteria Remote Handling Building Tritium Extraction Facility

International Nuclear Information System (INIS)

Mertz, G.

1999-01-01

This structural acceptance criteria contains the requirements for the structural analysis and design of the Remote Handling Building (RHB) in the Tritium Extraction Facility (TEF). The purpose of this acceptance criteria is to identify the specific criteria and methods that will ensure a structurally robust building that will safely perform its intended function and comply with the applicable Department of Energy (DOE) structural requirements

Construction of the main building network environment in IHEP

International Nuclear Information System (INIS)

Wang Yanming

2004-01-01

Based on the new network structure at IHEP, we re-constructed the network in Main Building at IHEP in order to realize the goal of steadily supporting the network application. We chose high performance and administrable switches and configured them properly. This improved that the network security, management ability. So the network at Main Building became more safe, steady, reliable and high-efficient. (authors)

OSSMETER D3.2 – Report on Source Code Activity Metrics

NARCIS (Netherlands)

J.J. Vinju (Jurgen); A. Shahi (Ashim)

2014-01-01

htmlabstractThis deliverable is part of WP3: Source Code Quality and Activity Analysis. It provides descriptions and initial prototypes of the tools that are needed for source code activity analysis. It builds upon the Deliverable 3.1 where infra-structure and a domain analysis have been

Rapid prototyping in order to improve building performance simulation for detailed design support

NARCIS (Netherlands)

Hopfe, C.J.; Hensen, J.L.M.; Stankov, P.

2006-01-01

Building performance simulation (BPS) is a powerful tool to support building and system designers in emulating how orientation, building type, HVAC system etc. interacts the overall building performance. Currently BPS is used only for code compliance in the detailed design, neither to make informed

Ethical Guidelines for Structural Interventions to Small-Scale Historic Stone Masonry Buildings.

Science.gov (United States)

Hurol, Yonca; Yüceer, Hülya; Başarır, Hacer

2015-12-01

Structural interventions to historic stone masonry buildings require that both structural and heritage values be considered simultaneously. The absence of one of these value systems in implementation can be regarded as an unethical professional action. The research objective of this article is to prepare a guideline for ensuring ethical structural interventions to small-scale stone historic masonry buildings in the conservation areas of Northern Cyprus. The methodology covers an analysis of internationally accepted conservation documents and national laws related to the conservation of historic buildings, an analysis of building codes, especially Turkish building codes, which have been used in Northern Cyprus, and an analysis of the structural interventions introduced to a significant historic building in a semi-intact state in the walled city of Famagusta. This guideline covers issues related to whether buildings are intact or ruined, the presence of earthquake risk, the types of structural decisions in an architectural conservation project, and the values to consider during the decision making phase.

Explicit Constructions and Bounds for Batch Codes with Restricted Size of Reconstruction Sets

OpenAIRE

Thomas, Eldho K.; Skachek, Vitaly

2017-01-01

Linear batch codes and codes for private information retrieval (PIR) with a query size $t$ and a restricted size $r$ of the reconstruction sets are studied. New bounds on the parameters of such codes are derived for small values of $t$ or of $r$ by providing corresponding constructions. By building on the ideas of Cadambe and Mazumdar, a new bound in a recursive form is derived for batch codes and PIR codes.

Organization and management of ATLAS nightly builds

International Nuclear Information System (INIS)

Luehring, F; Obreshkov, E; Quarrie, D; Rybkine, G; Undrus, A

2010-01-01

The automated multi-platform software nightly build system is a major component in the ATLAS collaborative software organization, validation and code approval schemes. Code developers from ATLAS participating Institutes spread all around the world use about 30 branches of nightly releases for testing new packages, verification of patches to existing software, and migration to new platforms and compilers. The nightly releases lead up to, and are the basis of, stable software releases used for data processing worldwide. The ATLAS nightly builds are managed by the fully automated NICOS framework on the computing farm with 44 powerful multiprocessor nodes. The ATN test tool is embedded within the nightly system and provides results shortly after full compilations complete. Other test frameworks are synchronized with NICOS jobs and run larger scale validation jobs using the nightly releases. NICOS web pages dynamically provide information about the progress and results of the builds. For faster feedback, E-mail notifications about nightly releases problems are automatically distributed to the developers responsible.

Building an ontology of pulmonary diseases with natural language processing tools using textual corpora.

Science.gov (United States)

Baneyx, Audrey; Charlet, Jean; Jaulent, Marie-Christine

2007-01-01

Pathologies and acts are classified in thesauri to help physicians to code their activity. In practice, the use of thesauri is not sufficient to reduce variability in coding and thesauri are not suitable for computer processing. We think the automation of the coding task requires a conceptual modeling of medical items: an ontology. Our task is to help lung specialists code acts and diagnoses with software that represents medical knowledge of this concerned specialty by an ontology. The objective of the reported work was to build an ontology of pulmonary diseases dedicated to the coding process. To carry out this objective, we develop a precise methodological process for the knowledge engineer in order to build various types of medical ontologies. This process is based on the need to express precisely in natural language the meaning of each concept using differential semantics principles. A differential ontology is a hierarchy of concepts and relationships organized according to their similarities and differences. Our main research hypothesis is to apply natural language processing tools to corpora to develop the resources needed to build the ontology. We consider two corpora, one composed of patient discharge summaries and the other being a teaching book. We propose to combine two approaches to enrich the ontology building: (i) a method which consists of building terminological resources through distributional analysis and (ii) a method based on the observation of corpus sequences in order to reveal semantic relationships. Our ontology currently includes 1550 concepts and the software implementing the coding process is still under development. Results show that the proposed approach is operational and indicates that the combination of these methods and the comparison of the resulting terminological structures give interesting clues to a knowledge engineer for the building of an ontology.

Resistor-logic demultiplexers for nanoelectronics based on constant-weight codes.

Science.gov (United States)

Kuekes, Philip J; Robinett, Warren; Roth, Ron M; Seroussi, Gadiel; Snider, Gregory S; Stanley Williams, R

2006-02-28

The voltage margin of a resistor-logic demultiplexer can be improved significantly by basing its connection pattern on a constant-weight code. Each distinct code determines a unique demultiplexer, and therefore a large family of circuits is defined. We consider using these demultiplexers for building nanoscale crossbar memories, and determine the voltage margin of the memory system based on a particular code. We determine a purely code-theoretic criterion for selecting codes that will yield memories with large voltage margins, which is to minimize the ratio of the maximum to the minimum Hamming distance between distinct codewords. For the specific example of a 64 × 64 crossbar, we discuss what codes provide optimal performance for a memory.

The RADionuclide Transport, Removal, and Dose (RADTRAD) code

International Nuclear Information System (INIS)

Miller, L.A.; Chanin, D.I.; Lee, J.

1993-01-01

The RADionuclide Transport, Removal, And Dose (RADTRAD) code is designed for US Nuclear Regulatory Commission (USNRC) use to calculate the radiological consequences to the offsite population and to control room operators following a design-basis accident at Light Water Reactor (LWR) power plants. This code utilizes updated reactor accident source terms published in draft NUREG-1465, ''Accident Source Terms for Light-Water Nuclear Power Plants.'' The code will track the transport of radionuclides as they are released from the reactor pressure vessel, travel through the primary containment and other buildings, and are released to the environment. As the radioactive material is transported through the primary containment and other buildings, credit for several removal mechanisms may be taken including sprays, suppression pools, overlying pools, filters, and natural deposition. Simple models are available for these different removal mechanisms that use, as input, information about the conditions in the plant and predict either a removal coefficient (λ) or decontamination factor. The user may elect to use these models or input a single value for a removal coefficient or decontamination factor

77 FR 29322 - Updating State Residential Building Energy Efficiency Codes

Science.gov (United States)

2012-05-17

... Glass Company North America (AGC). However, DOE notes that PNA/AGC's comment was received late. Although... following. Steel-framed wall insulation Air barrier location Changes whose effect is unclear: Fenestration... code's primary regulation of a home's envelope thermal resistance, or the resistance of the ceilings...

Impact of window selection on the energy performance of residential buildings in South Korea

International Nuclear Information System (INIS)

Ihm, Pyeongchan; Park, Lyool; Krarti, Moncef; Seo, Donghyun

2012-01-01

With rapidly increasing energy consumption attributed to residential buildings in South Korea, there is a need to update requirements of the building energy code in order to improve the energy performance of buildings. This paper provides some guidelines to improve the building energy code to better select glazing types that minimize total energy use of residential buildings in Korea. In particular, detailed energy simulation analyses coupled with economical and environmental assessments are carried out to assess the thermal, economical, and environmental impacts of glazing thermal characteristics as well as window sizes associated with housing units in various representative climates within South Korea. The results of the analyses have clearly indicated that selecting glazing with low solar heat gain coefficient is highly beneficial especially for large windows and for mild climates. In particular, it is found that using any double-pane low-e glazing would provide better performance for windows in residential buildings than the clear double-pane glazing, currently required by the Korean building energy code. - Highlights: ► Results show that windows can be energy neutral for residential buildings. ► In Korea, double-pane low-e glazing would provide better energy performance. ► Double low-e clear filled with argon gas glazing is the most cost-effective.

Effective coding with VHDL principles and best practice

CERN Document Server

Jasinski, Ricardo

2016-01-01

A guide to applying software design principles and coding practices to VHDL to improve the readability, maintainability, and quality of VHDL code. This book addresses an often-neglected aspect of the creation of VHDL designs. A VHDL description is also source code, and VHDL designers can use the best practices of software development to write high-quality code and to organize it in a design. This book presents this unique set of skills, teaching VHDL designers of all experience levels how to apply the best design principles and coding practices from the software world to the world of hardware. The concepts introduced here will help readers write code that is easier to understand and more likely to be correct, with improved readability, maintainability, and overall quality. After a brief review of VHDL, the book presents fundamental design principles for writing code, discussing such topics as design, quality, architecture, modularity, abstraction, and hierarchy. Building on these concepts, the book then int...

OSSMETER D3.4 – Language-Specific Source Code Quality Analysis

NARCIS (Netherlands)

J.J. Vinju (Jurgen); A. Shahi (Ashim); H.J.S. Basten (Bas)

2014-01-01

htmlabstractThis deliverable is part of WP3: Source Code Quality and Activity Analysis. It provides descriptions and prototypes of the tools that are needed for source code quality analysis in open source software projects. It builds upon the results of: • Deliverable 3.1 where infra-structure and

Status of MARS Code

Energy Technology Data Exchange (ETDEWEB)

N.V. Mokhov

2003-04-09

Status and recent developments of the MARS 14 Monte Carlo code system for simulation of hadronic and electromagnetic cascades in shielding, accelerator and detector components in the energy range from a fraction of an electronvolt up to 100 TeV are described. these include physics models both in strong and electromagnetic interaction sectors, variance reduction techniques, residual dose, geometry, tracking, histograming. MAD-MARS Beam Line Build and Graphical-User Interface.

Anticipatory research for the design of a sustainable and safe road traffic system.

NARCIS (Netherlands)

Oppe, S.

1993-01-01

The new policy in the Netherlands is attempting to build a traffic system, based on clear design concepts and rules about how to use it. Such a system should be sustainable and safe. The design characteristics of the roads should be relevant to their functions. It should be clear which vehicles are

Structural evaluation of the 2736Z Building for seismic loads

International Nuclear Information System (INIS)

Giller, R.A.

1994-01-01

The 2736Z building structure is evaluated for high-hazard loads. The 2736Z building is analyzed herein for normal and seismic loads and is found to successfully meet the guidelines of UCRL-15910 along with the related codes requirements

AP1000 shield building: a constructability challenge

International Nuclear Information System (INIS)

Di Giuseppe, Giovanni; Bonanno, Domenico

2010-01-01

The AP1000 Shield Building, an enhanced structure which surrounds the containment vessel, consists of standard Reinforced Concrete (RC) and composite Steel and Concrete (SC) construction. In the SC module the surface steel plates, (with attached shear studs and angles) filled with concrete, act as the steel reinforcement in concrete. This is a relatively new design technology that required the appropriate use of structural codes, supplemented with information from applicable tests on similar composite steel and concrete construction. Being a newer design concept, existing codes do not provide explicit guidance on SC construction so a review of literature and test data on composite structures similar to AP1000 shield building was done in order to confirm the technical basis for the design. The SC walls, air inlet structure and roof of the Shield Building will be constructed using modular construction practices and then transported to site and lifted into place. These modules, working also as permanent form-work, will be filled with high strength Self- Consolidating Concrete. (SCC) This paper provides a focused and integrated presentation of the enhanced shield building design methodology, testing, constructability and inspection. (authors)

Synthetic building materials for transport buildings and structures

Science.gov (United States)

Gerasimova, Vera

2017-10-01

The most effective building materials account for the highest growth not only in construction of residential and public buildings, but also other capital projects including roadways, bridges, drainage, communications and other engineering projects. Advancement in the technology of more efficient and ecologically responsible insulation materials have been a priority for safety, minimal maintenance and longevity of finished construction projects. The practical use of modern building materials such as insulation, sound reduction and low energy consumption are a benefit in cost and application compared to the use of outdated heavier and labor-intensive materials. The most efficient way for maximizing insolation and sound proofing should be done during the design stages of the project according to existing codes and regulations that are required by Western Government. All methods and materials that are used need to be optimized in order to reach a high durability and low operational and maintenance cost exceeding more than 50 years of the life of the building, whether it is for public, industrial or residential use. Western construction techniques and technologies need to be applied and adapted by the Russian Federation to insure the most productive successful methods are being implemented. The issues of efficient insulation materials are outlined in this article.

Validation of the TAC/BLOOST code (Contract research)

International Nuclear Information System (INIS)

Takamatsu, Kuniyoshi; Nakagawa, Shigeaki

2005-06-01

Safety demonstration tests using the High Temperature engineering Test Reactor (HTTR) are in progress to verify the inherent safety features for High Temperature Gas-cooled Reactors (HTGRs). The coolant flow reduction test by tripping gas circulators is one of the safety demonstration tests. The reactor power safely brings to a stable level without a reactor scram and the temperature transient of the reactor-core is very slow. The TAC/BLOOST code was developed to analyze reactor and temperature transient during the coolant flow reduction test taking account of reactor dynamics. This paper describes the validation result of the TAC/BLOOST code with the measured values of gas circulators tripping tests at 30% (9 MW). It was confirmed that the TAC/BLOOST code was able to analyze the reactor transient during the test. (author)

Disposal of Pesticide Wastes as Implemented in A Proposed Code of Practice in Egypt

International Nuclear Information System (INIS)

Sherif El-Hamady, E.

1999-01-01

In the present study , an Egyptian Code of Practice for the safe use of pesticides on farms and holdings is suggested. The Code has to be issued for the purpose of providing practical guidance to citizens especially farmers and growers engaged in crop production or to the authorities of companies and plants manufacturing and formulating pesticides in Egypt

Assessment of indoor environment of buildings

Energy Technology Data Exchange (ETDEWEB)

Fan, Y.; Kovanen, K. [VTT Building Technology, Espoo (Finland). Indoor Environment and Systems

1995-12-31

The synthetical assessment of indoor environment has become world-wide topic in recent years. Many research evidences have shown that the quality of indoor air is a multi-factor influenced issue. Building Research Establishment (BRE) in United Kingdom has worked out a series of assessing methods for different kinds of buildings. Whereas, in Finland, National Building Code of Finland has been used for many years. The comparison between the two approaches in assessing indoor air quality will be addressed in this presentation. Each issue considered in the above two approaches is discussed by referring the recent research highlights. (author)

Assessment of indoor environment of buildings

Energy Technology Data Exchange (ETDEWEB)

Fan, Y; Kovanen, K [VTT Building Technology, Espoo (Finland). Indoor Environment and Systems

1996-12-31

The synthetical assessment of indoor environment has become world-wide topic in recent years. Many research evidences have shown that the quality of indoor air is a multi-factor influenced issue. Building Research Establishment (BRE) in United Kingdom has worked out a series of assessing methods for different kinds of buildings. Whereas, in Finland, National Building Code of Finland has been used for many years. The comparison between the two approaches in assessing indoor air quality will be addressed in this presentation. Each issue considered in the above two approaches is discussed by referring the recent research highlights. (author)

NARMER-1: a photon point-kernel code with build-up factors

Science.gov (United States)

Visonneau, Thierry; Pangault, Laurence; Malouch, Fadhel; Malvagi, Fausto; Dolci, Florence

2017-09-01

This paper presents an overview of NARMER-1, the new generation of photon point-kernel code developed by the Reactor Studies and Applied Mathematics Unit (SERMA) at CEA Saclay Center. After a short introduction giving some history points and the current context of development of the code, the paper exposes the principles implemented in the calculation, the physical quantities computed and surveys the generic features: programming language, computer platforms, geometry package, sources description, etc. Moreover, specific and recent features are also detailed: exclusion sphere, tetrahedral meshes, parallel operations. Then some points about verification and validation are presented. Finally we present some tools that can help the user for operations like visualization and pre-treatment.

ClinicalCodes: an online clinical codes repository to improve the validity and reproducibility of research using electronic medical records.

Science.gov (United States)

Springate, David A; Kontopantelis, Evangelos; Ashcroft, Darren M; Olier, Ivan; Parisi, Rosa; Chamapiwa, Edmore; Reeves, David

2014-01-01

Lists of clinical codes are the foundation for research undertaken using electronic medical records (EMRs). If clinical code lists are not available, reviewers are unable to determine the validity of research, full study replication is impossible, researchers are unable to make effective comparisons between studies, and the construction of new code lists is subject to much duplication of effort. Despite this, the publication of clinical codes is rarely if ever a requirement for obtaining grants, validating protocols, or publishing research. In a representative sample of 450 EMR primary research articles indexed on PubMed, we found that only 19 (5.1%) were accompanied by a full set of published clinical codes and 32 (8.6%) stated that code lists were available on request. To help address these problems, we have built an online repository where researchers using EMRs can upload and download lists of clinical codes. The repository will enable clinical researchers to better validate EMR studies, build on previous code lists and compare disease definitions across studies. It will also assist health informaticians in replicating database studies, tracking changes in disease definitions or clinical coding practice through time and sharing clinical code information across platforms and data sources as research objects.

Energy and Energy Cost Savings Analysis of the 2015 IECC for Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jian [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Xie, YuLong [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Athalye, Rahul A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Zhuge, Jing Wei [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Rosenberg, Michael I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hart, Philip R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Liu, Bing [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2015-06-01

As required by statute (42 USC 6833), DOE recently issued a determination that ANSI/ASHRAE/IES Standard 90.1-2013 would achieve greater energy efficiency in buildings subject to the code compared to the 2010 edition of the standard. Pacific Northwest National Laboratory (PNNL) conducted an energy savings analysis for Standard 90.1-2013 in support of its determination . While Standard 90.1 is the model energy standard for commercial and multi-family residential buildings over three floors (42 USC 6833), many states have historically adopted the International Energy Conservation Code (IECC) for both residential and commercial buildings. This report provides an assessment as to whether buildings constructed to the commercial energy efficiency provisions of the 2015 IECC would save energy and energy costs as compared to the 2012 IECC. PNNL also compared the energy performance of the 2015 IECC with the corresponding Standard 90.1-2013. The goal of this analysis is to help states and local jurisdictions make informed decisions regarding model code adoption.

Energy and Energy Cost Savings Analysis of the 2015 IECC for Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Zhang, Jian [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Xie, YuLong [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Athalye, Rahul A. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Zhuge, Jing Wei [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Rosenberg, Michael I. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Hart, Philip R. [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States); Liu, Bing [Pacific Northwest National Laboratory (PNNL), Richland, WA (United States)

2015-09-01

As required by statute (42 USC 6833), DOE recently issued a determination that ANSI/ASHRAE/IES Standard 90.1-2013 would achieve greater energy efficiency in buildings subject to the code compared to the 2010 edition of the standard. Pacific Northwest National Laboratory (PNNL) conducted an energy savings analysis for Standard 90.1-2013 in support of its determination . While Standard 90.1 is the model energy standard for commercial and multi-family residential buildings over three floors (42 USC 6833), many states have historically adopted the International Energy Conservation Code (IECC) for both residential and commercial buildings. This report provides an assessment as to whether buildings constructed to the commercial energy efficiency provisions of the 2015 IECC would save energy and energy costs as compared to the 2012 IECC. PNNL also compared the energy performance of the 2015 IECC with the corresponding Standard 90.1-2013. The goal of this analysis is to help states and local jurisdictions make informed decisions regarding model code adoption.

Fusion PIC code performance analysis on the Cori KNL system

Energy Technology Data Exchange (ETDEWEB)

Koskela, Tuomas S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). National Energy Research Scientific Computing Center (NERSC); Deslippe, Jack [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). National Energy Research Scientific Computing Center (NERSC); Friesen, Brian [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). National Energy Research Scientific Computing Center (NERSC); Raman, Karthic [INTEL Corp. (United States)

2017-05-25

We study the attainable performance of Particle-In-Cell codes on the Cori KNL system by analyzing a miniature particle push application based on the fusion PIC code XGC1. We start from the most basic building blocks of a PIC code and build up the complexity to identify the kernels that cost the most in performance and focus optimization efforts there. Particle push kernels operate at high AI and are not likely to be memory bandwidth or even cache bandwidth bound on KNL. Therefore, we see only minor benefits from the high bandwidth memory available on KNL, and achieving good vectorization is shown to be the most beneficial optimization path with theoretical yield of up to 8x speedup on KNL. In practice we are able to obtain up to a 4x gain from vectorization due to limitations set by the data layout and memory latency.

Development of RESRAD probabilistic computer codes for NRC decommissioning and license termination applications

International Nuclear Information System (INIS)

Chen, S. Y.; Yu, C.; Mo, T.; Trottier, C.

2000-01-01

In 1999, the US Nuclear Regulatory Commission (NRC) tasked Argonne National Laboratory to modify the existing RESRAD and RESRAD-BUILD codes to perform probabilistic, site-specific dose analysis for use with the NRC's Standard Review Plan for demonstrating compliance with the license termination rule. The RESRAD codes have been developed by Argonne to support the US Department of Energy's (DOEs) cleanup efforts. Through more than a decade of application, the codes already have established a large user base in the nation and a rigorous QA support. The primary objectives of the NRC task are to: (1) extend the codes' capabilities to include probabilistic analysis, and (2) develop parameter distribution functions and perform probabilistic analysis with the codes. The new codes also contain user-friendly features specially designed with graphic-user interface. In October 2000, the revised RESRAD (version 6.0) and RESRAD-BUILD (version 3.0), together with the user's guide and relevant parameter information, have been developed and are made available to the general public via the Internet for use

Data on European non-residential buildings.

Science.gov (United States)

D'Agostino, Delia; Cuniberti, Barbara; Bertoldi, Paolo

2017-10-01

This data article relates to the research paper Energy consumption and efficiency technology measures in European non-residential buildings (D'Agostino et al., 2017) [1]. The reported data have been collected in the framework of the Green Building Programme that ran from 2006 to 2014. The project has encouraged the adoption of efficiency measures to boost energy savings in European non-residential buildings. Data focus on the one-thousand buildings that joined the Programme allowing to save around 985 GWh/year. The main requirement to join the Programme was the reduction of at least 25% primary energy consumption in a new or retrofitted building. Energy consumption before and after the renovation are provided for retrofitted buildings while, in new constructions, a building had to be designed using at least 25% less energy than requested by the country's building codes. The following data are linked within this article: energy consumption, absolute and relative savings related to primary energy, saving percentages, implemented efficiency measures and renewables. Further information is given about each building in relation to geometry, envelope, materials, lighting and systems.

Design experience on seismically isolated buildings

International Nuclear Information System (INIS)

Giuliani, G.C.

1991-01-01

This paper describes the practical problems associated with the structural design of seismically isolated buildings now under construction in Ancona, Italy. These structures are the first seismically isolated buildings in Italy. The Ancona region is in zone 2 of the Italian Seismic Code. It has a design acceleration of 0.07 g which corresponds to a ground surface acceleration of 0.25 g. The last significant earthquake was recorded on June 14, 1972, having a single shock-type wave with a peak acceleration of 0.53 g. Taking into account the aforesaid earthquake, the structural design of these new buildings was performed according to an acceleration spectrum which was different from the zone 2 seismic code and which provided protection for stronger ground motions. To minimize the cost of the structure, the buildings used ribbed plate decks, thus reducing the amount of material and the mass of the structures to be isolated. The design requirements, dynamic analysis performed, structural design, and practical engineering employed are reported in this paper. A comparison between the costs of a conventionally designed and a base-isolated structure is also reported. It shows a net savings of 7% for the base-isolated structure. The tests undertaken for certifying the mechanical properties of the isolators for both static and dynamic loads are also described, as is the full-scale dynamic test which is scheduled for next year (1990) for one of the completed buildings. (orig.)

A Practical Guide for Commissioning Existing Buildings

Energy Technology Data Exchange (ETDEWEB)

Haasl, T.

1999-05-11

Although this guide focuses on the retrocommissioning process and its advantages, all three types of commissioning--retrocommissioning, commissioning, and recommissioning--play an equally important role in ensuring that buildings perform efficiently and provide comfortable, safe, and productive work environments for owners and occupants. For new construction and retrofit projects, commissioning should be incorporated early, during design, and last throughout the length of the project. For buildings that were never commissioned, the retrocommissioning process can yield a wealth of cost-saving opportunities while enhancing a building's environment. Finally, once a building is commissioned or retrocommissioned, incorporating recommissioning into the organization's O and M program (by periodically reapplying the original diagnostic testing and checklist procedures) helps ensure that cost savings and other benefits gained from the original process persist over time.

A Practical Guide for Commissioning Existing Buildings

Energy Technology Data Exchange (ETDEWEB)

Haasl, T.; Sharp, T.

1999-04-01

Although this guide focuses on the retrocommissioning process and its advantages, all three types of commissioning--retrocommissioning, commissioning, and recommissioning--play an equally important role in ensuring that buildings perform efficiently and provide comfortable, safe, and productive work environments for owners and occupants. For new construction and retrofit projects, commissioning should be incorporated early, during design, and last throughout the length of the project. For buildings that were never commissioned, the retrocommissioning process can yield a wealth of cost-saving opportunities while enhancing a building's environment. Finally, once a building is commissioned or retrocommissioned, incorporating recommissioning into the organization's O and M program (by periodically reapplying the original diagnostic testing and checklist procedures) helps ensure that cost savings and other benefits gained from the original process persist over time.

Benchmark Simulation for the Development of the Regulatory Audit Subchannel Analysis Code

Energy Technology Data Exchange (ETDEWEB)

Lee, G. H.; Song, C.; Woo, S. W. [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

2012-05-15

For the safe and reliable operation of a reactor, it is important to predict accurately the flow and temperature distributions in the thermal-hydraulic design of a reactor core. A subchannel approach can give the reasonable flow and temperature distributions with the short computing time. Korea Institute of Nuclear Safety (KINS) is presently reviewing new subchannel code, THALES, which will substitute for both THINC-IV and TORC code. To assess the prediction performance of THALES, KINS is developing the subchannel analysis code for the independent audit calculation. The code is based on workstation version of COBRA-IV-I. The main objective of the present study is to assess the performance of COBRA-IV-I code by comparing the simulation results with experimental ones for the sample problems

Establishing a commercial building energy data framework for India

Energy Technology Data Exchange (ETDEWEB)

Iyer, Maithili [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kumar, Satish [Alliance for an Energy Efficient Economy, New Delhi (India); Mathew, Sangeeta [Alliance for an Energy Efficient Economy, New Delhi (India); Stratton, Hannah [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mathew, Paul A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Singh, Mohini [Synurja, Inc. (India)

2018-04-18

Buildings account for over 40% of the world’s energy consumption and are therefore a key contributor to a country’s energy as well as carbon budget. Understanding how buildings use energy is critical to understanding how related policies may impact energy use. Data enables decision making, and good quality data arms consumers with the tools to compare their energy performance to their peers, allowing them to differentiate their buildings in the real estate market on the basis of their energy footprint. Good quality data are also essential for policy makers to prioritize their energy saving strategies and track implementation. The United States’ Commercial Building Energy Consumption Survey (CBECS) is an example of a successful data framework that is highly useful for governmental and nongovernmental initiatives related to benchmarking energy forecasting, rating systems and metrics, and more. The Bureau of Energy Efficiency (BEE) in India developed the Energy Conservation Building Code (ECBC) and launched the Star Labeling program for a few energy-intensive building segments as a significant first step. However, a data driven policy framework for systematically targeting energy efficiency in both new construction and existing buildings has largely been missing. There is no quantifiable mechanism currently in place to track the impact of code adoption through regular reporting/survey of energy consumption in the commercial building stock. In this paper we present findings from our study that explored use cases and approaches for establishing a commercial buildings data framework for India.

Seismic strengthening of building 111 at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Eli, M.; Coats, D.; Freeland, G.; Kamath, M.

1991-01-01

Since being designed and constructed in the late 1960s, the Director's Building (Building 111) at Lawrence Livermore National Laboratory (LLNL) has been evaluated for 1988 seismic criteria and has been upgraded to withstand a major earthquake in the Livermore area. During and immediately after a large earthquake in the Livermore area, Building 111 occupants would be able to exit safely without loss of life. Building 111 itself would be severely damaged, but would not collapse. Highlights of the seismic upgrade design criteria and of the design, analyses, and construction that resulted are presented in this paper

A critical appraisal of codes as vehicles for realising on-site quality

NARCIS (Netherlands)

Van Breugel, K.

2014-01-01

The increasing demand for quality, durability and sustainability requires a critical evaluation of currently used building codes. Although there is no doubt that we need codes, standards, certificates etc., the existence of these documents are no guarantee that the prescribed quality is realized on

Building America Expert Meeting. Combustion Safety

Energy Technology Data Exchange (ETDEWEB)

Brand, Larry [Partnership for Advanced Residential Retrofit (PARR), Des Plaines, IL (United States)

2013-03-01

This is an overview of "The Best Approach to Combustion Safety in a Direct Vent World," held June 28, 2012, in San Antonio, TX. The objective of this Expert Meeting was to identify gaps and barriers that need to be addressed by future research, and to develop data-driven technical recommendations for code updates so that a common approach for combustion safety can be adopted by all members of the building energy efficiency and code communities.

Building America Expert Meeting: Combustion Safety

Energy Technology Data Exchange (ETDEWEB)

Brand, L.

2013-03-01

This is a meeting overview of 'The Best Approach to Combustion Safety in a Direct Vent World', held June 28, 2012, in San Antonio, Texas. The objective of this Expert Meeting was to identify gaps and barriers that need to be addressed by future research, and to develop data-driven technical recommendations for code updates so that a common approach for combustion safety can be adopted by all members of the building energy efficiency and code communities.

Storytelling Dramas as a Community Building Activity in an Early Childhood Classroom

Science.gov (United States)

Wright, Cheryl; Diener, Marissa L.; Kemp, Jacqueline Lindsay

2013-01-01

Healthy social-emotional development is promoted by building a safe, secure and respectful environment in an early childhood setting with positive and consistent relationships among adults, children, and their peers. This study explored storytelling dramas as an opportunity to build community within the context of one early childhood classroom.…

Optimized reversible binary-coded decimal adders

DEFF Research Database (Denmark)

Thomsen, Michael Kirkedal; Glück, Robert

2008-01-01

Abstract Babu and Chowdhury [H.M.H. Babu, A.R. Chowdhury, Design of a compact reversible binary coded decimal adder circuit, Journal of Systems Architecture 52 (5) (2006) 272-282] recently proposed, in this journal, a reversible adder for binary-coded decimals. This paper corrects and optimizes...... their design. The optimized 1-decimal BCD full-adder, a 13 × 13 reversible logic circuit, is faster, and has lower circuit cost and less garbage bits. It can be used to build a fast reversible m-decimal BCD full-adder that has a delay of only m + 17 low-power reversible CMOS gates. For a 32-decimal (128-bit....... Keywords: Reversible logic circuit; Full-adder; Half-adder; Parallel adder; Binary-coded decimal; Application of reversible logic synthesis...

An Investigation of the Methods of Logicalizing the Code-Checking System for Architectural Design Review in New Taipei City

Directory of Open Access Journals (Sweden)

Wei-I Lee

2016-12-01

Full Text Available The New Taipei City Government developed a Code-checking System (CCS using Building Information Modeling (BIM technology to facilitate an architectural design review in 2014. This system was intended to solve problems caused by cognitive gaps between designer and reviewer in the design review process. Along with considering information technology, the most important issue for the system’s development has been the logicalization of literal building codes. Therefore, to enhance the reliability and performance of the CCS, this study uses the Fuzzy Delphi Method (FDM on the basis of design thinking and communication theory to investigate the semantic difference and cognitive gaps among participants in the design review process and to propose the direction of system development. Our empirical results lead us to recommend grouping multi-stage screening and weighted assisted logicalization of non-quantitative building codes to improve the operability of CCS. Furthermore, CCS should integrate the Expert Evaluation System (EES to evaluate the design value under qualitative building codes.

CONTEMPT-DG containment analysis code

International Nuclear Information System (INIS)

Deem, R.E.; Rousseau, K.

1982-01-01

The assessment of hydrogen burning in a containment building during a degraded core event requires a knowledge of various system responses. These system responses (i.e. heat sinks, fan cooler units, sprays, etc.) can have a marked effect on the overall containment integrity results during a hydrogen burn. In an attempt to properly handle the various system responses and still retain the capability to perform sensitivity analysis on various parameters, the CONTEMPT-DG computer code was developed. This paper will address the historical development of the code, its various features, and the rationale for its development. Comparisons between results from the CONTEMPT-DG analyses and results from similar MARCH analyses will also be given

Improvement of Computer Codes Used for Fuel Behaviour Simulation (FUMEX-III). Report of a Coordinated Research Project 2008-2012

International Nuclear Information System (INIS)

2013-03-01

It is fundamental to the future of nuclear power that reactors can be run safely and economically to compete with other forms of power generation. As a consequence, it is essential to develop the understanding of fuel performance and to embody that knowledge in codes to provide best estimate predictions of fuel behaviour. This in turn leads to a better understanding of fuel performance, a reduction in operating margins, flexibility in fuel management and improved operating economics. The IAEA has therefore embarked on a series of programmes addressing different aspects of fuel behaviour modelling with the following objectives: - To assess the maturity and prediction capabilities of fuel performance codes, and to support interaction and information exchange between countries with code development and application needs (FUMEX series); - To build a database of well defined experiments suitable for code validation in association with the OECD Nuclear Energy Agency (OECD/NEA); - To transfer a mature fuel modelling code to developing countries, to support teams in these countries in their efforts to adapt the code to the requirements of particular reactors, and to provide guidance on applying the code to reactor operation and safety assessments; - To provide guidelines for code quality assurance, code licensing and code application to fuel licensing. This report describes the results of the coordinated research project on the ''Improvement of computer codes used for fuel behaviour simulation (FUMEX-III)''. This programme was initiated in 2008 and completed in 2012. It followed previous programmes on fuel modelling: D-COM 1982-1984, FUMEX 1993-1996 and FUMEX-II 2002-2006. The participants used a mixture of data derived from commercial and experimental irradiation histories, in particular data designed to investigate the mechanical interactions occurring in fuel during normal, transient and severe transient operation. All participants carried out calculations on priority

Analysis for Building Envelopes and Mechanical Systems Using 2012 CBECS Data

Energy Technology Data Exchange (ETDEWEB)

Winiarski, David W.; Halverson, Mark A.; Butzbaugh, Joshua B.; Cooke, Alan L.; Bandyopadhyay, Gopal K.; Elliott, Douglas B.

2018-03-14

This report describes the aggregation and mapping of certain building characteristics data available in the most recent Commercial Building Energy Consumption Survey (CBECS) (DOE EIA 2012) to describe most typical building construction practices. This report provides summary data for potential use in the support of modifications to the Pacific Northwest National Laboratory’s commercial building prototypes used for building energy code analysis. Specifically, this report outlines findings and most typical design choices for certain building envelope and heating, ventilating, and air-conditioning (HVAC) system choices.

Residential tornado safe room from commodity wood products – impact and wind pressure testing

Science.gov (United States)

Robert H. Falk; James J. Bridwell; C. Adam Senalik; Marshall Begel

2018-01-01

A tornado safe room is a shelter designed to provide protection during a tornado and is specifically engineered to resist the high wind pressures and debris impact generated by these high wind events. The required performance criteria of these shelters has been established and is found in the International Code Council Standard for the Design and Construction of Storm...

Coded Network Function Virtualization

DEFF Research Database (Denmark)

Al-Shuwaili, A.; Simone, O.; Kliewer, J.

2016-01-01

Network function virtualization (NFV) prescribes the instantiation of network functions on general-purpose network devices, such as servers and switches. While yielding a more flexible and cost-effective network architecture, NFV is potentially limited by the fact that commercial off......-the-shelf hardware is less reliable than the dedicated network elements used in conventional cellular deployments. The typical solution for this problem is to duplicate network functions across geographically distributed hardware in order to ensure diversity. In contrast, this letter proposes to leverage channel...... coding in order to enhance the robustness on NFV to hardware failure. The proposed approach targets the network function of uplink channel decoding, and builds on the algebraic structure of the encoded data frames in order to perform in-network coding on the signals to be processed at different servers...

The SafeCOP ECSEL Project: Safe Cooperating Cyber-Physical Systems Using Wireless Communication

DEFF Research Database (Denmark)

Pop, Paul; Scholle, Detlef; Hansson, Hans

2016-01-01

This paper presents an overview of the ECSEL project entitled "Safe Cooperating Cyber-Physical Systems using Wireless Communication" (SafeCOP), which runs during the period 2016 -- 2019. SafeCOP targets safety-related Cooperating Cyber-Physical Systems (CO-CPS) characterised by use of wireless...... detection of abnormal behaviour, triggering if needed a safe degraded mode. SafeCOP will also develop methods and tools, which will be used to produce safety assurance evidence needed to certify cooperative functions. SafeCOP will extend current wireless technologies to ensure safe and secure cooperation...

Atmospheric relative concentrations in building wakes

International Nuclear Information System (INIS)

Ramsdell, J.V. Jr.; Simonen, C.A.; Smyth, S.B.

1995-05-01

This report documents the ARCON95 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Regulatory Research for use in control room habitability assessments. The document includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON95 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more five percent of the time. These concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. Relative concentrations calculated by ARCON95 are significantly lower than concentrations calculated using the currently accepted procedure when winds are less than two meters per second. For higher wind speeds, ARCON95 calculates about the same concentrations as the current procedure

Building America FY 2016 Annual Report: Building America Is Driving Real Solutions in the Race to Zero Energy Homes

Energy Technology Data Exchange (ETDEWEB)

Sara Farrar, Stacey Rothgeb, Ben Polly, Lieko Earle, and Tim Merrigan

2016-12-01

The U.S. Department of Energy (DOE) Building America Program enables the transformation of the U.S. housing industry to achieve energy savings through energy-efficient, high-performance homes with improved durability, comfort, and health for occupants. Building America bridges the gap between the development of emerging technologies and the adoption of codes and standards by engaging industry partners in applied research, development, and demonstration of high-performance solutions.

Fire-safety engineering and performance-based codes

DEFF Research Database (Denmark)

Sørensen, Lars Schiøtt

project administrators, etc. The book deals with the following topics: • Historical presentation on the subject of fire • Legislation and building project administration • European fire standardization • Passive and active fire protection • Performance-based Codes • Fire-safety Engineering • Fundamental......Fire-safety Engineering is written as a textbook for Engineering students at universities and other institutions of higher education that teach in the area of fire. The book can also be used as a work of reference for consulting engineers, Building product manufacturers, contractors, building...... thermodynamics • Heat exchange during the fire process • Skin burns • Burning rate, energy release rate and design fires • Proposal to Risk-based design fires • Proposal to a Fire scale • Material ignition and flame spread • Fire dynamics in buildings • Combustion products and toxic gases • Smoke inhalation...

Safe use of mine winding ropes, volume 4: studies towards a code of practice for rope condition assessment.

CSIR Research Space (South Africa)

Borrello, M

1996-06-01

Full Text Available The aim of this investigation was the verification of the code of Practice for Rope Condition Assessment. Ropes were meant to be discarded according to the discard criteria as outlined in the code and then tested by the CSIR. The results...

Dose reduction factors from a radioactive cloud for large buildings

International Nuclear Information System (INIS)

Grand, J. le; Roux, Y.

1986-01-01

A set of complex and accurate computer codes has been established to determine the transport of photons emitted from a radioactive cloud through various media. The geometrical and physical description of large buildings with various numbers of floors and rooms can be done by the user. The codes can calculate, in any room or apartment, the characteristics of the photon fields (photon flux, energy flux and distribution, direction distribution) and whole-body absorbed dose rates in a phantom standing or lying on the floor. The dose reduction factor is then the quotient of the mean absorbed dose rate in the apartment to the absorbed dose rate in the phantom standing on the ground outdoors. Applications to several modern multistorey buildings are presented. The results show the influence of various parameters such as density and composition of building materials, the fraction of the external building surface containing apertures and initial photon energy. (author)

Lightning protection design of nuclear power plants. KTA safety code, version 6/99

International Nuclear Information System (INIS)

1999-06-01

This KTA safety code does not cover calculation methods for determination of lightning-induced voltage inputs to control room systems within the reactor building, as the literature presents a variety of applicable methods, which however cannot be directly applied to any power plant, due to the great diversity of geometries of the electrical systems and control room systems in nuclear power plants. Compliance with the design requirements of this safety code for shielding of buildings, and installation and shielding of cables, can be considered to offer the appropriate protection. (orig./CB) [de

Safety in nuclear power plant operation, including commissioning and decommissioning. A code of practice

International Nuclear Information System (INIS)

1978-01-01

Safe operation of a nuclear power plant postulates satisfactory siting, design, construction and commissioning, together with proper management and operation of the plant. This Code of Practice deals with the safety aspects of management, commissioning, operation and decommissioning of the plant. It forms part of the Agency's programme, referred to as the NUSS programme, for establishing Codes of Practice and Safety Guides relating to land-based stationary thermal neutron power plants. It has been prepared for the use of those responsible for the operation of stationary nuclear power plants, the main function of which is the generation of electrical and/or thermal power, and for the use of those responsible for regulating the operation of such plants. It is not intended for application to reactors used solely for experimental or research purposes. The provisions in the Code are designed to provide assurance that operational activities are carried out without undue radiological hazard to the general public and to persons on the site. It should be understood that the provisions in the Code set forth minimum requirements which shall be met in order to achieve safe operation of a nuclear power plant

Safe Kids Worldwide

Science.gov (United States)

... Blog Videos Newsletter facebook twitter instagram pinterest gplus youtube Search Menu Why It Matters Who We Are What We Do Find Your Safe Kids Safe Kids Day Main menu Keeping All Kids Safe Safety Tips Get Involved 4 Star Charity Donate Text Burns and Scalds 4 tips ...

How safe is safe enough?

International Nuclear Information System (INIS)

Desnoyers, B.; Chanzy, Y.

2004-01-01

The IAEA Regulations for the Safe Transport of Radioactive Material, were historically established with the objective to reduce the probability that persons be exposed to unacceptable doses due to normal operation or accident situations during transport of radioactive material. Based on the International Basic Safety Standards for Protection against Ionizing Radiation (BSS), the definition, which was adopted for an unacceptable dose for an accident situation, is the excess of the maximum dose limits permissible in a single year for the occupational exposure of a worker in the BSS. Concerning the severity of accident situations, it has always be clearly stated that the objective of the tests for demonstrating ability to withstand accident conditions of transport was not to cover every accident condition, but solely most of them. The last available evaluations regarding the rate of accidents which are covered by the standardised accident conditions of transport defined in the IAEA Regulations give a range of about 80%, plus or minus 15% which depends on transport mode and studies. Consequently, slight variations in the capabilities of the packages to meet the specified performance would probably not have significant consequences on the protection level in case of accident. In the assessment of the compliance with the regulations, the tendency of experts, taking advantage of the enhanced performances of computer calculation codes, is to ask more and more calculations, with more and more accuracy, leading to more and more restrictions. Consequently, cost and delay are considerably increased without any evidence of an equivalent effect on the level of protection. This paper will initiate a reflection on the general objectives and principles when implementing the Regulations, in such a way that demonstrations remain cost effective, taking into account evolution of the techniques and a high level of safety

Comparison of calculation and simulation of evacuation in real buildings

Science.gov (United States)

Szénay, Martin; Lopušniak, Martin

2018-03-01

Each building must meet requirements for safe evacuation in order to prevent casualties. Therefore methods for evaluation of evacuation are used when designing buildings. In the paper, calculation methods were tested on three real buildings. The testing used methods of evacuation time calculation pursuant to Slovak standards and evacuation time calculation using the buildingExodus simulation software. If calculation methods have been suitably selected taking into account the nature of evacuation and at the same time if correct values of parameters were entered, we will be able to obtain almost identical times of evacuation in comparison with real results obtained from simulation. The difference can range from 1% to 27%.

Benchmarking Heavy Ion Transport Codes FLUKA, HETC-HEDS MARS15, MCNPX, and PHITS

Energy Technology Data Exchange (ETDEWEB)

Ronningen, Reginald Martin [Michigan State University; Remec, Igor [Oak Ridge National Laboratory; Heilbronn, Lawrence H. [University of Tennessee-Knoxville

2013-06-07

Powerful accelerators such as spallation neutron sources, muon-collider/neutrino facilities, and rare isotope beam facilities must be designed with the consideration that they handle the beam power reliably and safely, and they must be optimized to yield maximum performance relative to their design requirements. The simulation codes used for design purposes must produce reliable results. If not, component and facility designs can become costly, have limited lifetime and usefulness, and could even be unsafe. The objective of this proposal is to assess the performance of the currently available codes PHITS, FLUKA, MARS15, MCNPX, and HETC-HEDS that could be used for design simulations involving heavy ion transport. We plan to access their performance by performing simulations and comparing results against experimental data of benchmark quality. Quantitative knowledge of the biases and the uncertainties of the simulations is essential as this potentially impacts the safe, reliable and cost effective design of any future radioactive ion beam facility. Further benchmarking of heavy-ion transport codes was one of the actions recommended in the Report of the 2003 RIA R&D Workshop".

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2012-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

ASME Code Efforts Supporting HTGRs

Energy Technology Data Exchange (ETDEWEB)

D.K. Morton

2011-09-01

In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

Methodology applied in Cuba for siting, designing, and building a radioactive waste repository under safety conditions

International Nuclear Information System (INIS)

Orbera, L.; Peralta, J.L.; Franklin, R.; Gil, R.; Chales, G.; Rodriguez, A.

1993-01-01

The work presents the methodology used in Cuba for siting, designing, and building a radioactive waste repository safely. This methodology covers both the technical and socio-economic factors, as well as those of design and construction so as to have a safe siting for this kind of repository under Cuba especial condition. Applying this methodology will results in a safe repository

Data Collection Handbook to Support Modeling Impacts of Radioactive Material in Soil and Building Structures

Energy Technology Data Exchange (ETDEWEB)

Yu, Charley [Argonne National Lab. (ANL), Argonne, IL (United States); Kamboj, Sunita [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Cheng [Argonne National Lab. (ANL), Argonne, IL (United States); Cheng, Jing-Jy [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-09-01

This handbook is an update of the 1993 version of the Data Collection Handbook and the Radionuclide Transfer Factors Report to support modeling the impact of radioactive material in soil. Many new parameters have been added to the RESRAD Family of Codes, and new measurement methodologies are available. A detailed review of available parameter databases was conducted in preparation of this new handbook. This handbook is a companion document to the user manuals when using the RESRAD (onsite) and RESRAD-OFFSITE code. It can also be used for RESRAD-BUILD code because some of the building-related parameters are included in this handbook. The RESRAD (onsite) has been developed for implementing U.S. Department of Energy Residual Radioactive Material Guidelines. Hydrogeological, meteorological, geochemical, geometrical (size, area, depth), crops and livestock, human intake, source characteristic, and building characteristic parameters are used in the RESRAD (onsite) code. The RESRAD-OFFSITE code is an extension of the RESRAD (onsite) code and can also model the transport of radionuclides to locations outside the footprint of the primary contamination. This handbook discusses parameter definitions, typical ranges, variations, and measurement methodologies. It also provides references for sources of additional information. Although this handbook was developed primarily to support the application of RESRAD Family of Codes, the discussions and values are valid for use of other pathway analysis models and codes.

Abstract feature codes: The building blocks of the implicit learning system.

Science.gov (United States)

Eberhardt, Katharina; Esser, Sarah; Haider, Hilde

2017-07-01

According to the Theory of Event Coding (TEC; Hommel, Müsseler, Aschersleben, & Prinz, 2001), action and perception are represented in a shared format in the cognitive system by means of feature codes. In implicit sequence learning research, it is still common to make a conceptual difference between independent motor and perceptual sequences. This supposedly independent learning takes place in encapsulated modules (Keele, Ivry, Mayr, Hazeltine, & Heuer 2003) that process information along single dimensions. These dimensions have remained underspecified so far. It is especially not clear whether stimulus and response characteristics are processed in separate modules. Here, we suggest that feature dimensions as they are described in the TEC should be viewed as the basic content of modules of implicit learning. This means that the modules process all stimulus and response information related to certain feature dimensions of the perceptual environment. In 3 experiments, we investigated by means of a serial reaction time task the nature of the basic units of implicit learning. As a test case, we used stimulus location sequence learning. The results show that a stimulus location sequence and a response location sequence cannot be learned without interference (Experiment 2) unless one of the sequences can be coded via an alternative, nonspatial dimension (Experiment 3). These results support the notion that spatial location is one module of the implicit learning system and, consequently, that there are no separate processing units for stimulus versus response locations. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

New extremal binary self-dual codes of lengths 64 and 66 from bicubic planar graphs

OpenAIRE

Kaya, Abidin

2016-01-01

In this work, connected cubic planar bipartite graphs and related binary self-dual codes are studied. Binary self-dual codes of length 16 are obtained by face-vertex incidence matrices of these graphs. By considering their lifts to the ring R_2 new extremal binary self-dual codes of lengths 64 are constructed as Gray images. More precisely, we construct 15 new codes of length 64. Moreover, 10 new codes of length 66 were obtained by applying a building-up construction to the binary codes. Code...

28 CFR 36.608 - Guidance concerning model codes.

Science.gov (United States)

2010-07-01

... Section 36.608 Judicial Administration DEPARTMENT OF JUSTICE NONDISCRIMINATION ON THE BASIS OF DISABILITY BY PUBLIC ACCOMMODATIONS AND IN COMMERCIAL FACILITIES Certification of State Laws or Local Building... private entity responsible for developing a model code, the Assistant Attorney General may review the...

Optics code development at Los Alamos

International Nuclear Information System (INIS)

Mottershead, C.T.; Lysenko, W.P.

1988-01-01

This paper is an overview of part of the beam optics code development effort in the Accelerator Technology Division at Los Alamos National Laboratory. The aim of this effort is to improve our capability to design advanced beam optics systems. The work reported is being carried out by a collaboration of permanent staff members, visiting consultants, and student research assistants. The main components of the effort are: building a new framework of common supporting utilities and software tools to facilitate further development; research and development on basic computational techniques in classical mechanics and electrodynamics; and evaluation and comparison of existing beam optics codes, and support for their continuing development. 17 refs

Optics code development at Los Alamos

International Nuclear Information System (INIS)

Mottershead, C.T.; Lysenko, W.P.

1988-01-01

This paper is an overview of part of the beam optics code development effort in the Accelerator Technology Division at Los Alamos National Laboratory. The aim of this effort is to improve our capability to design advanced beam optics systems. The work reported is being carried out by a collaboration of permanent staff members, visiting consultants, and student research assistants. The main components of the effort are building a new framework of common supporting utilities and software tools to facilitate further development. research and development on basic computational techniques in classical mechanics and electrodynamics, and evaluation and comparison of existing beam optics codes, and support for their continuing development

Building Interactive Simulations in Web Pages without Programming.

Science.gov (United States)

Mailen Kootsey, J; McAuley, Grant; Bernal, Julie

2005-01-01

A software system is described for building interactive simulations and other numerical calculations in Web pages. The system is based on a new Java-based software architecture named NumberLinX (NLX) that isolates each function required to build the simulation so that a library of reusable objects could be assembled. The NLX objects are integrated into a commercial Web design program for coding-free page construction. The model description is entered through a wizard-like utility program that also functions as a model editor. The complete system permits very rapid construction of interactive simulations without coding. A wide range of applications are possible with the system beyond interactive calculations, including remote data collection and processing and collaboration over a network.

Detailed thermal-hydraulic computation into a containment building

Energy Technology Data Exchange (ETDEWEB)

Caruso. A.; Flour, I.; Simonin, O. [EDF/LNH, Chatou (France); Cherbonnel, C [EDF/SEPTEN, Villeurbanne (France)

1995-09-01

This paper deals with numerical predictions of the influence of water sprays upon stratifications into a containment building using a two-dimensional two-phase flow code. Basic equations and closure assumptions are briefly presented. A test case in a situation involving spray evaporation is first detailed to illustrate the validation step. Then results are presented for a compressible recirculating flow into a containment building with condensation phenomena.

Focusing on Mental Health, Not Metal Detectors: Three Building Blocks of Safe and Effective Schools.

Science.gov (United States)

Simpson, Richard; Kline, Sue Ann; Barnhill, Gena; Griswold, Deborah

2000-01-01

Many measures schools are implementing in response to recent violence will protect students but do little to address the complex social interactions that support violence. This article describes an approach that includes five research-based steps for creating safe and effective schools. This approach contains ways to help the learning environment,…

Building Technologies Program Multi-Year Program Plan Technology Validation and Market Introduction 2008

Energy Technology Data Exchange (ETDEWEB)

None, None

2008-01-01

Building Technologies Program Multi-Year Program Plan 2008 for technology validation and market introduction, including ENERGY STAR, building energy codes, technology transfer application centers, commercial lighting initiative, EnergySmart Schools, EnergySmar

Uncertainties associated with the use of the KENO Monte Carlo criticality codes

International Nuclear Information System (INIS)

Landers, N.F.; Petrie, L.M.

1989-01-01

The KENO multi-group Monte Carlo criticality codes have earned the reputation of being efficient, user friendly tools especially suited for the analysis of situations commonly encountered in the storage and transportation of fissile materials. Throughout their twenty years of service, a continuing effort has been made to maintain and improve these codes to meet the needs of the nuclear criticality safety community. Foremost among these needs is the knowledge of how to utilize the results safely and effectively. Therefore it is important that code users be aware of uncertainties that may affect their results. These uncertainties originate from approximations in the problem data, methods used to process cross sections, and assumptions, limitations and approximations within the criticality computer code itself. 6 refs., 8 figs., 1 tab

Fusion safety codes International modeling with MELCOR and ATHENA- INTRA

CERN Document Server

Marshall, T; Topilski, L; Merrill, B

2002-01-01

For a number of years, the world fusion safety community has been involved in benchmarking their safety analyses codes against experiment data to support regulatory approval of a next step fusion device. This paper discusses the benchmarking of two prominent fusion safety thermal-hydraulic computer codes. The MELCOR code was developed in the US for fission severe accident safety analyses and has been modified for fusion safety analyses. The ATHENA code is a multifluid version of the US-developed RELAP5 code that is also widely used for fusion safety analyses. The ENEA Fusion Division uses ATHENA in conjunction with the INTRA code for its safety analyses. The INTRA code was developed in Germany and predicts containment building pressures, temperatures and fluid flow. ENEA employs the French-developed ISAS system to couple ATHENA and INTRA. This paper provides a brief introduction of the MELCOR and ATHENA-INTRA codes and presents their modeling results for the following breaches of a water cooling line into the...

Postirradiation Testing Laboratory (327 Building)

International Nuclear Information System (INIS)

Kammenzind, D.E.

1997-01-01

A Standards/Requirements Identification Document (S/RID) is the total list of the Environment, Safety and Health (ES and H) requirements to be implemented by a site, facility, or activity. These requirements are appropriate to the life cycle phase to achieve an adequate level of protection for worker and public health and safety, and the environment during design, construction, operation, decontamination and decommissioning, and environmental restoration. S/RlDs are living documents, to be revised appropriately based on change in the site's or facility's mission or configuration, a change in the facility's life cycle phase, or a change to the applicable standards/requirements. S/RIDs encompass health and safety, environmental, and safety related safeguards and security (S and S) standards/requirements related to the functional areas listed in the US Department of Energy (DOE) Environment, Safety and Health Configuration Guide. The Fluor Daniel Hanford (FDH) Contract S/RID contains standards/requirements, applicable to FDH and FDH subcontractors, necessary for safe operation of Project Hanford Management Contract (PHMC) facilities, that are not the direct responsibility of the facility manager (e.g., a site-wide fire department). Facility S/RIDs contain standards/requirements applicable to a specific facility that are the direct responsibility of the facility manager. S/RlDs are prepared by those responsible for managing the operation of facilities or the conduct of activities that present a potential threat to the health and safety of workers, public, or the environment, including: Hazard Category 1 and 2 nuclear facilities and activities, as defined in DOE 5480.23. Selected Hazard Category 3 nuclear, and Low Hazard non-nuclear facilities and activities, as agreed upon by RL. The Postirradiation Testing Laboratory (PTL) S/RID contains standards/ requirements that are necessary for safe operation of the PTL facility, and other building/areas that are the direct

Postirradiation Testing Laboratory (327 Building)

Energy Technology Data Exchange (ETDEWEB)

Kammenzind, D.E.

1997-05-28

A Standards/Requirements Identification Document (S/RID) is the total list of the Environment, Safety and Health (ES and H) requirements to be implemented by a site, facility, or activity. These requirements are appropriate to the life cycle phase to achieve an adequate level of protection for worker and public health and safety, and the environment during design, construction, operation, decontamination and decommissioning, and environmental restoration. S/RlDs are living documents, to be revised appropriately based on change in the site`s or facility`s mission or configuration, a change in the facility`s life cycle phase, or a change to the applicable standards/requirements. S/RIDs encompass health and safety, environmental, and safety related safeguards and security (S and S) standards/requirements related to the functional areas listed in the US Department of Energy (DOE) Environment, Safety and Health Configuration Guide. The Fluor Daniel Hanford (FDH) Contract S/RID contains standards/requirements, applicable to FDH and FDH subcontractors, necessary for safe operation of Project Hanford Management Contract (PHMC) facilities, that are not the direct responsibility of the facility manager (e.g., a site-wide fire department). Facility S/RIDs contain standards/requirements applicable to a specific facility that are the direct responsibility of the facility manager. S/RlDs are prepared by those responsible for managing the operation of facilities or the conduct of activities that present a potential threat to the health and safety of workers, public, or the environment, including: Hazard Category 1 and 2 nuclear facilities and activities, as defined in DOE 5480.23. Selected Hazard Category 3 nuclear, and Low Hazard non-nuclear facilities and activities, as agreed upon by RL. The Postirradiation Testing Laboratory (PTL) S/RID contains standards/ requirements that are necessary for safe operation of the PTL facility, and other building/areas that are the direct

Hydrogen burn assessment with the CONTAIN code

International Nuclear Information System (INIS)

van Rij, H.M.

1986-01-01

The CONTAIN computer code was developed at Sandia National Laboratories, under contract to the US Nuclear Regulatory Commission (NRC). The code is intended for calculations of containment loads during severe accidents and for prediction of the radioactive source term in the event that the containment leaks or fails. A strong point of the CONTAIN code is the continuous interaction of the thermal-hydraulics phenomena, aerosol behavior and fission product behavior. The CONTAIN code can be used for Light Water Reactors as well as Liquid Metal Reactors. In order to evaluate the CONTAIN code on its merits, comparisons between the code and experiments must be made. In this paper, CONTAIN calculations for the hydrogen burn experiments, carried out at the Nevada Test Site (NTS), are presented and compared with the experimental data. In the Large-Scale Hydrogen Combustion Facility at the NTS, 21 tests have been carried out. These tests were sponsored by the NRC and the Electric Power Research Institute (EPRI). The tests, carried out by EG and G, were performed in a spherical vessel 16 m in diameter with a design pressure of 700 kPa, substantially higher than that of most commercial nuclear containment buildings

U.S. Department of Energy Solar Decathlon: Challenging Students to Build Energy Efficient, Cost-Effective, and Attractive Solar-Powered Houses

Energy Technology Data Exchange (ETDEWEB)

Simon, J.

2012-01-01

The U.S. Department of Energy Solar Decathlon challenges collegiate teams to design, build, and operate solar-powered houses that are cost-effective, energy-efficient, and attractive. The winner of the competition is the team that best blends affordability, consumer appeal, and design excellence with optimal energy production and maximum efficiency. The paper discusses the solutions developed for the event. We believe that the solutions implemented for Solar Decathlon 2011 represent current trends and that by analyzing, critiquing, and exposing the solutions pursued, the industry can become better suited to address challenges of the future. Constructing a solar community using high-efficiency design and unique materials while remaining code compliant, safe, and effective results in solutions that are market relevant, important, and interesting to the industry as a whole.

Building competence in radiation protection and the safe use of radiation sources. Safety guide

International Nuclear Information System (INIS)

2005-01-01

An essential element of a national infrastructure for radiation protection and safety is the maintenance of an adequate number of competent personnel. This Safety Guide makes recommendations concerning the building of competence in protection and safety, which relate to the training and assessment of qualification of new personnel and retraining of existing personnel in order to develop and maintain appropriate levels of competence. This Safety Guide addresses training in protection and safety aspects in relation to all practices and intervention situations in nuclear and radiation related technologies. This document covers the following aspects: the categories of persons to be trained. The requirements for education, training and experience for each category. The processes of qualification and authorization of persons. A national strategy for building competence

ASPECTS CONCERNING THE PRIVATE OWNERSHIP RIGHT WITHIN THE CONTEXT OF THE NEW CIVIL CODE

Directory of Open Access Journals (Sweden)

Ana-Maria Lupulescu

2012-11-01

Full Text Available The new Civil Code introduces several important changes and clarifications regarding the ownership right in general, and the private ownership right, in particular, so that it becomes necessary, for both the analyst in law and the practitioner, to make a comparison between the old regulation contained in the Civil Code of 1864 and the current regulation provided by the new Civil Code. At least in theory, the new legal framework in this area shows greater consistency and legal precision, although it is not entirely safe from any criticism.

"Same Room, Safe Place".

Science.gov (United States)

Keene Woods, Nikki

2017-04-01

There are many different professional stances on safe sleep and then there is the reality of caring for a newborn. There is a debate among professionals regarding safe sleep recommendations. The continum of recommendations vary from the American Academy of Pediatrics (AAP) Safe Sleep Guidelines to the bed-sharing recommendations from the Mother-Baby Behavioral Sleep Laboratory. The lack of consistent and uniform safe sleep recommendations from health professionals has been confusing for families but has more recently raised a real professional ethical dilemma. Despite years of focused safe sleep community education and interventions, sleep-related infant deaths are on the rise in many communities. This commentary calls for a united safe sleep message from all health professionals to improve health for mothers and infants most at-risk, "Same Room, Safe Place."

Training program for energy conservation in new-building construction. Volume IV. Energy conservation technology: advanced course for plan examiners

Energy Technology Data Exchange (ETDEWEB)

None

1977-12-01

A Model Code for Energy Conservation in New Building Construction has been developed by those national organizations primarily concerned with the development and promulgation of model codes. The technical provisions are based on ASHRAE Standard 90-75 and are intended for use by state and local officials. This manual contains a more in-depth training in the review techniques and concepts required by the plan examiners and code officials in administering the code for conventional (buildings of 3 stories or less) construction.

Results and Lessons Learned From the DOE Commercial Building Partnerships: Preprint

Energy Technology Data Exchange (ETDEWEB)

Hirsch, A.; Deru, M.; Langner, R.; Stark, G.; Doebber, I.; Scheib, J.; Sheppy, M.; Bonnema, E.; Pless, S.; Livingood, B.; Torcellini, P.

2014-09-01

Over the course of 5 years, NREL worked with commercial building owners and their design teams in the DOE Commercial Building Partnerships (CBP) to cut energy consumption by 50% in new construction (versus code) and by 30% in existing building pilot projects (versus code or pre-retrofit operational energy use depending on the preference of the Partner) using strategies that could be replicated across their building portfolios. A number of different building types were addressed, including supermarket, retail merchandise, combination big box (general merchandise and food sales), high rise office space, and warehouse. The projects began in pre-design and included a year of measurement data to evaluate performance against design expectations. Focused attention was required throughout the entire process to achieve a design with the potential to hit the energy performance target and to operate the resulting building to reach this potential. This paper will report quantitative results and cover both the technical and the human sides of CBP, including the elements that were required to succeed and where stumbling blocks were encountered. It will also address the impact of energy performance goals and intensive energy modeling on the design process innovations and best practices.

BOA: Framework for Automated Builds

CERN Document Server

Ratnikova, N

2003-01-01

Managing large-scale software products is a complex software engineering task. The automation of the software development, release and distribution process is most beneficial in the large collaborations, where the big number of developers, multiple platforms and distributed environment are typical factors. This paper describes Build and Output Analyzer framework and its components that have been developed in CMS to facilitate software maintenance and improve software quality. The system allows to generate, control and analyze various types of automated software builds and tests, such as regular rebuilds of the development code, software integration for releases and installation of the existing versions.

BOA: Framework for automated builds

International Nuclear Information System (INIS)

Ratnikova, N.

2003-01-01

Managing large-scale software products is a complex software engineering task. The automation of the software development, release and distribution process is most beneficial in the large collaborations, where the big number of developers, multiple platforms and distributed environment are typical factors. This paper describes Build and Output Analyzer framework and its components that have been developed in CMS to facilitate software maintenance and improve software quality. The system allows to generate, control and analyze various types of automated software builds and tests, such as regular rebuilds of the development code, software integration for releases and installation of the existing versions

Format for description of building envelope components for use in an optimization process

DEFF Research Database (Denmark)

Rudbeck, Claus Christian; Svendsen, Sv Aa Højgaard

1999-01-01

are decided by the architect or kept within limits due to public regulations, but even when these factors have been decided, some are left to be decided. Aspects like durability and the thermal performance are seldom specified by the architect, but might be addressed in national building codes. The national...... building codes specify minimum requirements for the aspects in question, but no trade-offs between the different aspects are allowed, being un-flexible. To allow for the use of optimization procedures in the design process a larger degree of flexibility is needed but first of all there is a need......When designing a building the number of possible combinations of aspects related to the performance of the building envelope are almost unlimited. Due to the physical laws governing e.g. the static performance of the building, some aspects should be kept within a certain interval. Other aspects...

Building competence in radiation protection and the safe use of radiation sources. Safety guide (Spanish ed.)

International Nuclear Information System (INIS)

2010-01-01

This Safety Guide makes recommendations concerning the building of competence in protection and safety within a national radiation protection infrastructure and provides guidance for setting up the structure for a national strategy. It relates to the training and assessment of qualification of new personnel and the retraining of existing personnel in order to develop and maintain appropriate levels of competence. It provides the necessary guidance to meet the requirements laid down in Safety Series No. 115, International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. Contents: 1. Introduction; 2. Responsibilities for building competence in protection and safety; 3. Education, training and work experience; 4. A national strategy for building competence in protection and safety.

Building competence in radiation protection and the safe use of radiation sources. Safety guide (Arabic ed.)

International Nuclear Information System (INIS)

2006-01-01

This Safety Guide makes recommendations concerning the building of competence in protection and safety within a national radiation protection infrastructure and provides guidance for setting up the structure for a national strategy. It relates to the training and assessment of qualification of new personnel and the retraining of existing personnel in order to develop and maintain appropriate levels of competence. It provides the necessary guidance to meet the requirements laid down in Safety Series No. 115, International Basic Safety Standards for Protection against Ionizing Radiation and for the Safety of Radiation Sources. Contents: 1. Introduction; 2. Responsibilities for building competence in protection and safety; 3. Education, training and work experience; 4. A national strategy for building competence in protection and safety.

Development of a coupling code for PWR reactor cavity radiation streaming calculation

International Nuclear Information System (INIS)

Zheng, Z.; Wu, H.; Cao, L.; Zheng, Y.; Zhang, H.; Wang, M.

2012-01-01

PWR reactor cavity radiation streaming is important for the safe of the personnel and equipment, thus calculation has to be performed to evaluate the neutron flux distribution around the reactor. For this calculation, the deterministic codes have difficulties in fine geometrical modeling and need huge computer resource; and the Monte Carlo codes require very long sampling time to obtain results with acceptable precision. Therefore, a coupling method has been developed to eliminate the two problems mentioned above in each code. In this study, we develop a coupling code named DORT2MCNP to link the Sn code DORT and Monte Carlo code MCNP. DORT2MCNP is used to produce a combined surface source containing top, bottom and side surface simultaneously. Because SDEF card is unsuitable for the combined surface source, we modify the SOURCE subroutine of MCNP and compile MCNP for this application. Numerical results demonstrate the correctness of the coupling code DORT2MCNP and show reasonable agreement between the coupling method and the other two codes (DORT and MCNP). (authors)

Code of practice for radiation protection in dentistry (1987)

International Nuclear Information System (INIS)

1988-01-01

This code is intended as a guide to safe practices and lays down detailed requirements for the following protective measures : allocation of responsibility and need for clinical assessment of the indications for radiography; provision of appropriate equipment, film and processing facilities; adoption of procedures to minimise exposure to radiation. This code deals with radiographic procedures commonly used in general and specialist dental practice. These entail : intra-oral radiography: periapical, bitewing and occlusal views; panoramic radiography: intra-oral tube radiography and panoramic tomography; radiography of the complete skull or certain parts of the dento-maxillo-facial region; hand and wrist radiography for the sole purpose of the determination of the bone age

Ice condenser containment analysis with the GOTHIC code

International Nuclear Information System (INIS)

Yadon, T.P.

1996-01-01

Analytical methodologies have recently been developed by Duke Power Company (Duke) to calculate the thermodynamic response of the ice condenser containment buildings at the McGuire and Catawba Nuclear Stations to high-energy line breaks. The GOTHIC computer code (Version 4.0) was utilized for these analyses. In the ice condenser containment design, a large mass of ice stored within the containment building is used to absorb the energy released from high-energy line breaks, thereby limiting the peak pressure and temperature in the containment building to within design limits. The McGuire and Catawba Nuclear Stations (both two-unit, 3411 MWth four-loop Westinghouse plants) are of the ice condenser containment design

Comparison of computer codes related to the sodium oxide aerosol behavior in a containment building

International Nuclear Information System (INIS)

Fermandjian, J.

1984-09-01

In order to ensure that the problems of describing the physical behavior of sodium aerosols, during hypothetical fast reactor accidents, were adequately understood, a comparison of the computer codes (ABC/INTG, PNC, Japan; AEROSIM, UKAEA/SRD, United Kingdom; PARDISEKO IIIb, KfK, Germany; AEROSOLS/A2 and AEROSOLS/B1, CEA France) was undertaken in the frame of the CEC: exercise in which code users have run their own codes with a prearranged input