Energy Technology Data Exchange (ETDEWEB)

The creep behaviour of boiler drums of CuNiMo steels depends on the ratio of the alloys, the heat treatment and the processing technology. Reduction in deformability must be expected but, under optimum conditions, this does not lead to a critical material condition. The appropriate material tests are indispensable. (orig.)

Energy Technology Data Exchange (ETDEWEB)

In view of the situation that aging of boiler components proceeds and some `Type IV` cracking incidents are reported recently, the development of an accurate remaining life evaluation method for boiler weldment parts is an important subject for the utilities. In this study, simulated materials with coarse and fine grain microstructures in a weldment heat affected zone were produced, and their high temperature strength properties were evaluated. The strength property of the weld joint was also discussed based on the experimental and analytical results. It was found that the creep rupture strength of the fine grain material was as low as 1/2 of the base metal and as 1/5 of the coarse grain material, and the weld joint ruptured at the fine grain region in a shorter period than the base metal as the applied stress level decreased. Many grainboundary creep cavities were also observed in the fine grain region. A creep deformation analysis by FEM ...

International Nuclear Information System (INIS)

Results from a heavily fouled 19 tube C-E model boiler test to investigate the potential for egg crate corrosion in aggressively fouled AVT chemistry are reported. Substantial support plate and egg crate corrosion was produced in this test. Carbon steel drilled support plates exhibited extensive denting which resulted in flow hole ligament cracking. Corrosion of the carbon steel egg crate, through-wall at areas of tube contact, resulted in denting of the Alloy 600 heat transfer tubes. Corrosion performance of the 409 stainless steel egg crate was improved compared to the carbon steel egg crate although localized through-wall corrosion was noted. The results from the above test and previously reported tests were compared based on the following simplifying assumptions: maximum dent size and/or corrosion penetrations utilized, average bulk water chloride concentrations, pilling ...

International Nuclear Information System (INIS)

Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to considerable investigation of the mechanism of corrosion and for palliatives. The basic mechanism is now fairly well understood. Chloride present in the boiler feedwater from condenser leakage is concentrated in the support plate crevice as a result of the superheat present. This leads to the formation of a low pH acid ferrous chloride environment either through the hydrolysis of a weak base chloride such as MgCl_2 or the combined action of a neutral chloride with an oxidizing agent. Rapid attack of the carbon steel ensues with the Fe_3O_4 corrosion product forming at the metal/oxide interface. This oxide has a volume approximately twice that of the steel consumed and thus eventually fills the crevice between the tube and the support plate. Oxide growth continues leading to ...

Energy Technology Data Exchange (ETDEWEB)

A series of short articles discusses: use of a chemically bonded ceramic composite liner, WellerDensit, to protect the steel surface of pulverizer classifier cones; use of a fused cast basalt liners developed by Abresist Corp. in pipes for transporting coal and ash; a survey completed by the National Energy Technology Laboratory to identify causes of outages and other concerns expressed by PC and FBC boiler operators; and Temp-Age, Early Visc-Age and Modern Visc-Age systems for controlling the viscosity of heavy fuel oil to maintain proper combustion. 7 figs.

Science.gov (United States)

... Originator-supplied keywords include: Turbulators, Heat transfer augmentation, Enhancement, Fire tube boilers. (Author). ...

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers where feedwater was polluted with sea or river water. Specific effects of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hrs for seawater pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water, denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid, or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high seawater pollution. Soaks cannot stop denting if they are not followed by an on-line ...

Energy Technology Data Exchange (ETDEWEB)

Candidate materials for components of a fluidized-bed waste heat recovery system (FBWHRS) include plain carbon steel, types 405 and 316 stainless steel, and alloy 800. These materials were exposed to synthetic flue gas at anticipated FBWHRS temperatures and higher for 3000 h to determine corrosion rates. The synthetic flue gas was a combustion atmosphere to which Cl/sub 2/ and HCl were added. The projected annual corrosion rate for plain carbon steel is about 0.08 mm/year (0.003 in./year) at 250 to 290/sup 0/C, but it would exceed 0.5 mm/year (0.02 in./year) at 560/sup 0/C. The projected annual corrosion rates of the other materials were less than 0.25 mm/year (0.01 in./year) at the maximum test temperatures of 560, 660, and 665/sup 0/C for type 405, type 316, and alloy 800, respectively. These results indicate that corrosion of candidate FBWHRS materials will not be significant at anticipated operating temperatures for ...

Science.gov (United States)

...2010-10-01 false Electric hot water supply boilers. 63.25-3 Section 63.25-3...Boilers § 63.25-3 Electric hot water supply boilers. (a) Electric hot water supply boilers that have a capacity not...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This article describes innovations in new-boiler startups, based on experiences at United Development Group`s 50-MW Niagra cogeneration facility, Niagra Falls, NY. The plant comprises: a circulating coal fluidized bed boiler supplying steam to a nearby factory and electricity to the grid. Before operation the system was flushed with demineralized water, and the boiler degreased, the steam blow relied on a new procedure involving a continuous flow of steam. Startup was then initiated, following manufacturers heatup rate and soak times closely. After startup boiler tube sections were checked, and cleaned if necessary. 1 fig.

Energy Technology Data Exchange (ETDEWEB)

This report describes the arrangement and features of the Ogishima thermal power plant facilities, as well as activities being performed there for operation control, regular inspection and improvement in reliability. The power plant uses about 48 percent of the by-product gas as its fuel to supply about 81 percent of the required power. Operation of the No. 1 unit started in 1976. Currently, the plant has three units, each with an output of 125MW. Each unit consists of a natural circulation boiler with a maximum evaporation capacity of 410 ton/hour and a reheat regenerative condensing turbine with a main vapor pressure of 127 kg/cm/sup 2/G. Techniques used for water properties control and combustion control are also described. In the plant, convetional time management integrity techniques are now being replaced by state management integrity techniques that determines the deterioration tendency in separate sections of the facilities which are divided in ...

Science.gov (United States)

The report presents detailed technical information concerning application of flue gas desulfurization (FGD) systems to industrial boilers. The information was obtained by a survey of plant personnel, control system vendors, regulatory agencies, and consulting engineering firms. T...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The relations between nuclear energy availability and nuclear plant safety are analyzed in the particular cases of naval propulsion nuclear boilers (aircraft carriers, submarines): safety objectives, present and potential risk analysis, optimization of the availability-safety couple, at the design stage and during operation (procedural rules related to the boiler state, real time decisions). 6 fig., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The CASTOC project addresses environmentally assisted cracking (EAC) phenomena in low alloy steels used for pressure boundary components in both Western type boiling water reactors (BWR) and Russian type pressurised water reactors (VVER). It comprises the four work packages (WP): inter-laboratory comparison test (WP1); EAC behaviour under static load (WP2), EAC behaviour under cyclic load and load transients (WP3); evaluation of the results with regard to their relevance for components in practice (WP4). The use of sophisticated test facilities and measurement techniques for the on-line detection of crack advances have provided a more detailed understanding of the mechanisms of environmentally assisted cracking and provided quantitative data of crack growth rates as a function of loading events and time, respectively. The effect of several major parameters controlling EAC was investigated with particular emphasis on the transferability of the results to components ...

Energy Technology Data Exchange (ETDEWEB)

In the atmospheric pressure coal combustion area, the Internally Circulating Fluidized Bed Boiler (ICFB) had already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and because of its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and low-pollution characteristics. From fiscal 1992, the authors have conducted extensive research work, including cold model tests and computer simulations to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the Pressurized Internally Circulating Fluidized Bed Boiler (PICFB). Based on the ...

International Nuclear Information System (INIS)

The use of pre-dehumidified air having widely established itself as a safe and economical conservation method during the stoppage of steam turbines, it was obvious that this method would be applied also to steam boilers and ancillary aggregates. Experience with the conservation of condensers, prheaters and the water/steam-side of steam boilers in large-scale power stations is reported on. By the example of projects with topical interest, the problems and possibilities of boiler conservation on the firing side are illustrated. The contribution is to stimulate further discussions. (orig.).

Science.gov (United States)

... the effect of MBH on steam generator crevice corrosion; model boiler test results show that MBH is effective against denting corrosion and Alloy 600 ...

Energy Technology Data Exchange (ETDEWEB)

Accurate prediction of tube surface temperature is important for determining whether accelerated superheater corrosion will occur in kraft recovery boilers. A heat transfer model, which combines an iterative numerical solution scheme with a more realistic flue gas flow field obtained from the CFD code FLUENT, has been developed to predict the tube, steam and flue gas temperatures in the superheater region. Results of tests performed for a recovery boiler show that temperatures predicted using the model are in good agreement with actual temperatures measured using thermocouples. The presence of a large flue gas recirculation zone above the bullnose is shown to have an adverse effect on the heat transfer in the superheater region. 9 refs., 12 figs., 1 tab.

Science.gov (United States)

... Accession Number : ADA092132. Title : Analysis of Flue Gas Desulfurization (FGD) Processes for Potential Use on Army Coal-Fired Boilers. ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Steam generation is an integral part of most chemical process plants; however, the steam plant often is or can be overlooked in the area of hazard analysis. The reasons for this oversight are obvious: steam generation is considered to be an old and well-understood process, and steam boiler systems are often not considered to pose the same hazards as other plant units. However, modern steam boiler systems are fueled with natural gas, pulverized coal, and/or fuel oil; each of which poses significant fire and explosion hazards. For example, a moderately sized chemical plant's boiler house may have two or three boilers operating at 240 MMBTU/hr, with each using approximately 11 ton/hr of subbituminous pulverized coal feed. Chemical plants rely on equipment design and installation, mai...

CERN Document Server

Specification of the steel sheet for the 300 GeV magnet system

International Science & Technology Center (ISTC)

Development of the Corrosion Protection Technology for Special Steels and Alloys

Energy Technology Data Exchange (ETDEWEB)

Mechanical properties of P-LDHA and V-ROL N steels of the Czech production are compared with other ultra-high strength steels produced in the world. The most important results can be summarized into following points: 1. Optimally heat treated P-LDHA steel exhibits substantially better strength characteristics then the V-ROL N steel. 2. Optimal tempering temperature of the P-LDHA steel is 300 C. 3. Basic mechanical properties of P-LDHA steel belong to the top of the UHS steels ranking and are well comparable with those of American 300 M steel. 4. In the low-cycle fatigue region, the P-LDHA steel exhibits slightly better fatigue resistance then the 300 M steel. On the other hand, the high-cycle fatigue resistance of 300 M steel is slightly better then that of ...

Science.gov (United States)

An extended series of measurements at a conventional coal-fired boiler equipped with a wet-limestone flue gas desulfurization unit has shown that sulfate and sulfur dioxide removal efficiencies are dissimilar. The average SO2 scrubbing efficiency was 76% and was observed to decrease over a five-day operating cycle. Total sulfate scrubbing efficiency, averaging about 29%, was invariant throughout the operating cycle. (1 diagram, 3 tables)

Science.gov (United States)

A post-accident-heat-removal structural effects analysis for the steel liner in the FFTF concrete containment structure is presented. (JWR)

Energy Technology Data Exchange (ETDEWEB)

During a regular inspection of the Boiler Auxiliaries at one of the Dutch Electricity Production Companies serious cracks were found in the cover and casings of the feed water circulation pumps in two units after 108.000 and 122.000 hours of boiler operation. Kema Laboratories carried out Failure analyses on boat samples at the cracked areas. Corrosion fatigue cracking was found on the inner side of the GS-24CrNiMo325 casing. Shop Weld repairs were carried out using a newly developed mechanized Plasma Welding Technique. The repaired feed water circulation pumps showed no problems alter several years of operation. The costs of repair were substantially lower than the costs of replacement. (orig.) 3 refs.

Science.gov (United States)

This report gives the results of a survey of operational flue gas desulfurization (FGD) systems on coal-fired utility boilers in the United States. The FGD systems installed on Units 1 and 2 at the Bruce Mansfield Station of the Pennsylvania Power Company...

Energy Technology Data Exchange (ETDEWEB)

The CPCU steam distribution network is supplemented by a return network for the condensation water. The data system installed in 1988 provides, for the real time, management of the function of the two networks and a reduction in production costs. For the steam, data required in the network, the boiler houses and from external sources are processed by local network of five microprocessors and permit: - with time delay: technical and economic production optimizing calculations, or forecasts, for the following day, of the total required output and the procedure necessary for supplying this at the lowest cost; - in real time: on the basis of the forecasts for the previous day, creating the production instructions for the boiler houses and the instructions for the network remote control elements; - in case of an unexpected occurrence: immediate creation of new operating forecasts for the boiler houses for the establishing ...

Science.gov (United States)

Legal aspects of using natural gas as boiler fuel for electric utilities are reviewed through one utility's challenges to the Power Plant and Industrial Fuel Use implementation. ASARCO vs. FPC, 1973, and City of Willcox vs. FPC are discussed. (PSB)

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under 38 symposia. Subjects included reinforced concrete, protective coatings and linings, cathodic/anodic protection, chemical cleaning of boilers, managing corrosion with plastics, water treatment, HRSG boiler tube failure analysis, corrosion in oil and gas production, corrosion in petroleum refining and gas, processing, pipelines and tanks, high temperature materials, chemical process industry, aerospace equipment, materials technology developments for incinerators and waste fuel-fired processors, materials and corrosion in fossil-fuels conversion and combustion, corrosion in nuclear systems, marine corrosion, building systems, corrosion mechanisms, corrosion inhibitors and corrosion monitoring and measurement.

Energy Technology Data Exchange (ETDEWEB)

The automotive industry desires to optimize safety and lightweight construction for the production of cars and trucks. The resulting task for steel suppliers is to make steel grades available that can fulfil these requirements. Different projects have shown optimistic outlooks for optimization of safety and reduction of the weight of automobile bodies by using different high strength and ultra high strength steels. In the last group the dual phase steels play the lead. In recent years different steel grades have been developed and optimized for these applications. On one hand developing the mechanical properties as well as joining and forming of dual phase steels is one of the first steps. On the other hand different coated surfaces for various applications of dual phase steels is another step. Starting with characteristic production ...

International Nuclear Information System (INIS)

The influence of chemical composition and heat treatment on a low-carbon steel, chromium steel and high speed steel has been examined by polarisation curves and electrochemical parameters deduced from the Tafel plots. The electrochemical corrosion resistance, which is small between the as-received steels become greater after heat treatment, following the order: carbon steel < chromium steel #approx# high speed steel. To explain these differences, the nano- and microstructure of the steels has been characterized by the ex situ techniques of atomic force microscopy and optical microscopy, before and after surface etching with Nital (a solution of 5% HNO_3 in ethanol). This causes preferential attack of the ferrite phases showing the carbide phases more clearly. From these nanostructural studies it was possible to better ...

Science.gov (United States)

... rate on the tensile properties of SA-106 carbon steel pipe, in support of analysis and experimental modeling of postulated pipe whip in nuclear ...

CERN Document Server

Differences in synchrotron radiation induced gas desorption from stainless steel and aluminium alloy

Energy Technology Data Exchange (ETDEWEB)

There are two types in quench distortion of steel parts: thermal distortion and transformation distortion. Quench distortion is caused mainly by uneven cooling rate of steel parts from Austenitising temperature. The rapid cooled side is lengthened (convex deformation); the slow cooled side is shortened (concave deformation). So, to control the quench distortion, it is necessary to regulate the cooling rate of steel parts during quenching. TWO COMPONENTS produce the quench distortion of steel parts: the thermal stress and transformation stress. Generally, the effect of the thermal stress on the quench distortion is stronger than the transformation stress. The quench distortion is caused by uneven cooling rate of the steel parts, from Austenitising temperature to Ms point and Ms-Mf range. So, to control the quench distortion, it is very important to regulate the cooling rate of the ...

International Nuclear Information System (INIS)

Russian (Jan 1976). USSR Mironov, Yu.M. Makarov, VA Nauchno-

International Nuclear Information System (INIS)

Three model boilers, manufactured to simulate full-size tube sheet crevices, were tested with various secondary side environments. The first was faulted with organics representative of the decomposition of humic acid. The second was faulted with sodium carbonate and sodium hydroxide, while the third was faulted with sodium sulfate and sodium hydroxide. Each model contained seven tubes, which included Alloy 600 in the mill-annealed (MA) and thermally-treated (TT) conditions and Alloy 690 in the thermally-treated condition. Two models contained Alloy 800 tubes in the mill-annealed condition and one had Alloy 800 in the mill-annealed/cold-worked/glass-bead-peened condition. Two different sizes of tubesheet crevices were used in all model boilers. In the organics-faulted boiler, tubes of Alloy 600MA, Alloy 690TT and Alloy 800MA experienced no significant intergranular attack (IGA); however, the Alloy 600TT had intergranular ...

Energy Technology Data Exchange (ETDEWEB)

The primary objective of the project is to investigate the long-term effects of commercially available tangentially-fired low NO{sub x} combustion technologies on NOx emissions and boiler performance on Unit 2 at Gulf Power Company's Plant Lansing Smith located near Lynn Haven, Florida. The project will characterize emissions and performance of a tangentially-fired boiler operating in the following configurations: Baseline as-found'' configuration: Phase 1; retrofitted low NO{sub x} concentric firing system (LNCFS) Level 2 and simulated low NO{sub x} bulk furnace staging (LNBFS): Phase 2; retrofitted low NO{sub x} concentric firing system (LNCFS) Level 3, Phase 3a and simulated LNCFS Level 1, Phase 3b.

British Library Electronic Table of Contents (United Kingdom)

The fossil fuel consumption and pollutant emissions in a coal fired fluidized bed boiler could be reduced by biomass pyrolysis gas reburning. The influence of three kinds of biomass pyrolysis gases on the emission of N2O in a laboratory scale fluidized bed was investigated using the mechanism of GRI3.0 in this paper. The results showed that: the effect of sawdust pyrolysis gas reburning on N2O was more significant than that of rice husk and orange peel under the same conditions; the increase of initial oxygen content from 1% to 8% in flue gas would restrain the decomposition of N2O; the N2O decomposition was enhanced by increasing reaction temperature from 1073.15 K to 1323.15 K, and the decomposition rate may reach 99% at 1223.15 K.

Energy Technology Data Exchange (ETDEWEB)

This is a process for producing calcium sulfate dihydrate during desulfurization of stack gases from power station boilers, where the stack gases are introduced into a washing tower and are treated with a washing water suspension containing lime in the washing tower, where oxygen in the form of air or of air enriched in oxygen is also blown into the washing tower, and where the washing water suspension drawn off from the washing tower is fed back to the washing tower at a temperature of 45 to 50/sup 0/C in the circuit and at least part of the flow goes via a thickener and where calcium sulfate dihydrate slurry is drawn off from the thickener.

International Nuclear Information System (INIS)

A particle-laden turbulent reacting flow model is described and applied to in-furnace, dry SO_2 control in boilers. Sulfur capture by calcium-based sorbents is represented by a shrinking core model which accounts for surface areas loss and product layer diffusion. Sorbent particle trajectories and dispersion are followed with cloud statistics in a Lagrangian framework. The turbulent fluid mechanics and chemical reactions are coupled, and solutions obtained for mean and fluctuating velocity, composition, and particle position. Comparisons are made with data from an US EPA laboratory reactor. Practical implications for SO_2 control are examined including the effects of jet velocity, sorbent injection location, boiler load and thermal profiles.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

... Engineering, Kitakyushu, Fukuoka (Japan) Hattanda, Takumi NTT Advanced

International Nuclear Information System (INIS)

Both the price of nickel and the allergic reaction that it can cause to human beings make it desirable to develop and use nickel-free austenitic stainless steels. The steels should be austenitic so as to avoid ferro-magnetism, a condition which has to be fulfilled for a number of requirements, including its use as implants in the human body, for wrist watch cases and many others. The paper presents the development of a nickel-free steel containing 11 percent manganese, 17 percent chromium, 4 percent molybdenum, and 0.9 percent nitrogen. This austenitic stainless steel has exceptional strength and corrosion resistance. These properties could result in numerous applications of the steel. A limitation, however, is that the steel is not weldable.

Energy Technology Data Exchange (ETDEWEB)

In this book over 250 alloys are organized by AISI number into 10 major sections: Irons, Carbon Steels, Alloy Steels, Low Alloy Constructional Steels, Ultra High Strength Steels, Tool Steels, Maraging Steels, Wrought Stainless Steels, Heat Resistnat Casting Alloys, and Iron Based Rought Superalloys. Each alloy record lists the designation, specifications, UNS number, composition, product forms and a comment on the high-temperature properties and applications. Referenced data is then given for physical properties such as density, specific heat, thermal conductivity, thermal expansion, electrical conductivity, Poisson's ratio, moduli of elasticity and rigidity, etc. Mechanical properties follow, and include tensile properties, shearing and bearing properties, impact properties, creep, stress rupture and stress relaxation and fatigue ...

International Nuclear Information System (INIS)

The results have been presented of DC polarization and exposure investigations of alloy steels used as construction materials in flue gas desulphurization installations. on the base of analysis of composition of investigated steels and results of polarization studies, conditions have been discussed in which the pitting resistance equivalent (PRE) should be used. Among tested steels the significantly highest resistance to pitting corrosion is exhibited by 654SMO steel, classified as the super austenitic grade. (author). 14 refs, 3 figs, 2 tabs.

International Nuclear Information System (INIS)

author.The chemical and mechanical properties of S235jr structural low carbon mild steel were tested and reported for specimens collected from the Lebanese steel market. European and American standards were presented as references and compared with the achieved results. Discussion was conducted to show the similarities and differences between S235JR steel samples and standard requirements. Some of the reasons for such differences were discussed. A database was furnished through this work for the public and mainly for the Lebanese Standard Organization LIBNOR to easily adopt and implement a standard that has been tested in Lebanon concerning the hot rolled low carbon structural steels

International Nuclear Information System (INIS)

Recent data on resistance of modern corrosion-resistant austenitic-ferritic steels to different types of corrosion are generalized. It is shown that these steels are characterized by high resistance to general corrosion in acid, alkali, chloride and other solutions, are not inclined to intercrystalline, pitting and crevice corrosion and are noted for high resistance to corrosion cracking and corrosion fatigue. All this is combined with technological and economical effectiveness. It is advisible to use these steels instead of highly-alloyed and expensive steels and alloys in chemical, power and other industries. 59 refs.; 2 tabs.

Science.gov (United States)

The report gives results of a survey of the flue gas desulfurization (FGD) systems at Kansas City Power and Light Co.'s Hawthorn Power Station. The FGD systems on Hawthorn boilers 3 and 4 were designed to operate by injection of dry limestone in the boile...

Energy Technology Data Exchange (ETDEWEB)

Amidst the explosion of greenfield natural gas-fired combined-cycle plant development, opportunities still exist for valuable plant repowering and retrofits by taking advantages of unique technical and market conditions. One of the projects discussed is the rebuilding of the coal-fired Hawthorne unit 5 damaged by a boiler explosion. 3 tabs., 5 photos.

International Nuclear Information System (INIS)

Various electrochemical techniques are available to continuously monitor corrosion in conditions simulating those on the secondary side of PWR steam generators. This paper reviews those electrochemical techniques which are potentially useful to measure denting in tube-support crevices in situ. Attention is also given to corollary needs for monitoring the water chemistry which leads to corrosive attack. Finally some suggestions are offered for corrosion monitoring in autoclaves, model boilers and operating steam generators.

Science.gov (United States)

In this third, and concluding, article of the series the emission limits set by the US Clean Air Act and its amendements are set out. A number of flue gas desulfurization processes that have been developed for the utility and industrial markets are evaluated. Annual operating costs are indicated.

Energy Technology Data Exchange (ETDEWEB)

After the completion of the 4MWth pilot plant of the Pressurizied Internally Circulating Fluidized-bed Boiler (PICFB), a total of 15 test runs, amounting to 2280 hours of operation, were concluded. The test results have confirmed the superior operating performance. Additionally, Ebara plans to develop a Pressurized Internally Circulating Fluidized-bed Gasifier (PICFG or Advanced PICFB). 8 figs.

Science.gov (United States)

In addition to an executive summary and glossary, the following sections are included: Clean Boiler Fuel Demonstration Plant; Development of Coal Feeders for Coal Gasification Operations; Development of a Continuous Dry Coal Screw Feeder; Coal Feeder Development Program; Engineering and Technical Support; and Technical Assistance Services. (EJH)

International Nuclear Information System (INIS)

Irradiation of ferritic steels with neutrons in the temperture range of room temperature to #propor to# 450deg C results in lattice hardening, which causes an increase in strength and a decrease in ductility. Eight reduced-activation Cr-W-V stels with chromium concentration varying from 2.25 to 12% were irradiated at 365deg C to #propor to# 7 dpa in the Fast Flux Test Facility. A steel with 2.25% Cr and the combination of 2% W and 0.25% V hardened less than those containing vanadium or tungsten alone or a steel with 1% W and 0.25% V. The amount of hardening was similar for Cr-W-V steels with constant vanadium and tungsten concentrations and containing 2.,25, 5, and 9% Cr; a steel with 12% Cr hardened considerably more. Specimens of two conventional Cr-Mo steels, 9Cr-1MoVNb and 12Cr-1MoVW, were also irradiated, and the hardening of these ...

Energy Technology Data Exchange (ETDEWEB)

Described herein are effects of nitrogen dissolved in steel on passivity and pitting corrosion, as one of the major corrosion phenomena observed in stainless steel. Mechanisms involved in controlling pitting corrosion by nitrogen are also discussed. Nitrogen contained in austenic stainless steel is concentrated in the surface area, in particular in the vicinity of the interface between the passive film and metal matrix. Nitrogen tends to decrease critical current density in an acid, when it is added to steel of high critical current density (approximately 1mA/cm{sup 2} or higher). This phenomenon is considered to result from accumulation of nitrogen preferentially in the surface area to prevent dissolution of steel. Nitrogen dissolved in the austenic phase improves resistance of the steel to pitting corrosion. This phenomenon is considered to result from ...

Energy Technology Data Exchange (ETDEWEB)

Stainless steels can be nitrided at temperatures {<=}400 C to increase their hardness and wear resistance without a decreasing of their excellent corrosion resistance. Structure and properties of the surface layers produced by plasma nitriding and plasma immersion ion implantation in this temperature range were tested. There are negligible differences in the structure of the produced surface layers in spite of different interaction principles of the used technologies. However there are clear differences between the case of different steels. The case of ferritic chromium steels mainly consists of {epsilon}-nitride. Whereas the cases of austenitic and ferritic austenitic steels are characterized by expanded austenite. The corrosion resistance of the steels is reduced by nitriding only, if evident CrN-formation occurs. (orig.) 11 refs.

Energy Technology Data Exchange (ETDEWEB)

Four commercial stainless steels (mat. Nos. 1.4539, 1.4586, 1.4571 and 1.4462) were tested in 96% and 90% sulfuric acid of 80/sup 0/C as to their corrosion fatigue strength by subjecting notched round bars to the rotary bending test. At the same time, the efficiency of anodic protection was examined. With all four steels, the alternating bending strength obtained in the air is essentially reduced. The semiaustenitic steel Nr. 1.4462 shows a lower corrosion fatigue strength than the three austenitic steels. Although making the corrosion fatigue strength of steels better calculable, anodic protection proves insufficient to completely prevent notched round bars from corrosion fatigue in concentrated sulfuric acid.

Wastenet

...3 MtC, with 78% of these emissions from integrated steel making (26.9 MtC) and the rest (22%)...6 MtC, with 71% of these emissions from integrated steel making (21.9 MtC) and the rest (29%)...1 million ton of carbon (MtC) in 1994 (3.9 MtC from integrated steel making, and 2.2 MtC from secondary ...7 MtC in 2002 (3.7 MtC from integrated steel making, and 2.0 MtC from secondary steel making), corresponding ...

Science.gov (United States)

This study deals with the torsional response of Ti-8823 and 18Ni (200) maraging steel. The effect of different heat treatments and the subsequent change in microstructure are investigated. In the case of the Ti-8823, a comparison was made between the solu...

International Nuclear Information System (INIS)

May 2010 p. 81-84 Japan Ishizawa, Makoto JFE Steel Corporation, Tokyo

UK PubMed Central (United Kingdom)

Hundreds of thousands of people worldwide live or work in close proximity to steel mills. Integrated steel production generates chemical pollution containing compounds that can induce genetic damage...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Energy Technology Data Exchange (ETDEWEB)

Steel is one of the most versatile materials known to mankind. It is used in a variety of applications. In many of these applications, it is exposed to the atmosphere, leading to rust formation, which weakens structures made using steel. Hence, protection is important. The popular methods to prevent corrosion are painting, galvanizing, electroplating etc. The widely used Chrome etching process is very effective in corrosion inhibition as well as in hardening the steel. But, Chromium and its compounds are highly placed among the toxic chemicals listed under pollution prevention initiatives of the EPA. Hence, it was decided to find alternatives to this process.

Energy Technology Data Exchange (ETDEWEB)

In recent years, the phase stability of austenitic stainless steels, and its effect on the mechanical properties of stainless steels, have been the subject of much interest. With the availability of new experimental techniques, new theoretical methods, and new computational procedures, significant advances have been made in understanding, and being able to predict, phase stability and mechanical properties of stainless steel welds. This paper reviews some of these developments, with an emphasis on recent work that has been done at Oak Ridge National Laboratory.

International Nuclear Information System (INIS)

Mixed microstructures have been studied in low- carbon microalloyed steels suitable for automotive applications, after continuous cooling from the hot-rolled condition. Microstructural features such as polygonal ferrite, bainitic and acicular ferrite and microphase constituent are identified using transmission electron microscopy. The influence of these mixed structures on the tensile strength, impact toughness and fracture behaviour is examined. It is found that improvements in impact toughness as compared with microalloyed medium- carbon ferrite/pearlite steels can be achieved from these predominantly acicular structures developed by controlling alloy composition and continuous cooling of these lower carbon steels. (orig.).

International Nuclear Information System (INIS)

A study is made into microhardness and structure of coatings on various system steels (37G2S, 25Kh5M, R6M5), obtained by ion nitriding in a low pressure (10"-"1 Pa) arc discharge plasma. A comparison of properties is accomplished for steels nitrided in an arc gas discharge and in a furnace. It is stated that ion-plasma nitriding in an arc gas plasma generator is an efficient method of alloy steels hardening which allows changing the structure and increasing the hardness of a surface layer up to rather great depth

International Nuclear Information System (INIS)

The influence of microalloying vanadium or titanium on improving the corrosion resistance of mild steel in saturated calcium hydroxide solution was investigated. Potential-time, potentiodynamic polarization, and impedance measurement techniques were employed. The corrosion products have been examined by infrared and X-ray diffraction analysis and by scanning electron microscopy. It has been shown that the grain refining, due to microalloying, plays an important role in enhancing the corrosion resistance of steel. Scales of calcite and iron oxides on top of a protective oxide are formed on the investigated steels.

Energy Technology Data Exchange (ETDEWEB)

This study does not recommend the use of a pressure vessel made of integral stainless steel, due to the failure mechanisms under stress corrosion assisted by chlorides or polythionic acid. Are presented case studies of literature and analysis of reports of proceedings of RLAM reactors, showing that the materials produced by bimetallic clad overlay or are more appropriate, in terms of integrity, for use in equipment that the internal environment requires austenitic stainless steel specification.

International Nuclear Information System (INIS)

Effect of scale on determination of 12Kh18N10T steel tendency to intergranular corrosion (IGC) by rapid electrochemical techniques in solution of 10 % H_2SO_4+0.0025 g/l KCNS was investigated. It is shown that scale presence of steel surface accelerates anode dissolving, activates grain boundaries. All this results to the effect of tendency to IGC in steels, not inclined to it. The scale is not completely removed from the surface, but remains partially along grain boundaries in result of successive pickling of scale and then a surface layer of metal. This also couses the effect of tendency to IGC.

Energy Technology Data Exchange (ETDEWEB)

It is known that in size reduction of the granular structure of ferrite and ferrite-pearlite steels the temperature of the transformation from ductile to brittle condition is lowered. This effect can also be caused by an increase in the dispersity of intragrain and intergrain segregations (sulfides, carbonitrides, and segregations of impurity atoms), which accompanies grain size reduction and promotes initiation and propagation of cracks. In order to clarify the mechanism of fracture of steel in the region of the ductile-brittle transition steel 45 with different grain sizes and pearlite morphologies has been investigated.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

... Japan) Kobayashi, Minoru AITEL Corp., Yokohama, Kanagawa (Japan)

Energy Technology Data Exchange (ETDEWEB)

Given that fossil fuel fired power plants are among the largest and most concentrated producers of CO{sub 2} emissions, recovery and sequestration of CO{sub 2} from the flue gas of such plants has been identified as one of the primary means for reducing anthropogenic CO{sub 2} emissions. In this study, ALSTOM Power Inc. (ALSTOM) has investigated several coal fired power plant configurations designed to capture CO{sub 2} from effluent gas streams for use or sequestration. Burning fossil fuels in mixtures of oxygen and recirculated flue gas (made principally of CO{sub 2}) essentially eliminates the presence of atmospheric nitrogen in the flue gas. The resulting flue gas is comprised primarily of CO{sub 2}. Oxygen firing in utility scale Pulverized Coal (PC) fired boilers has been shown to be a more economical method for CO{sub 2} capture than amine scrubbing (Bozzuto, et al., 2001). Additionally, oxygen firing in Circulating Fluid Bed Boilers ...

Energy Technology Data Exchange (ETDEWEB)

By magnetron sputtering model steel films with specific properties can be prepared for purposive surveys. By changing the deposition parameters certain properties of these films can be influenced. For this thesis steel films with 18% Cr and 8% Ni have been prepared in order to study specific parameters on the corrosion resistance of bulk stainless steel. Chemical composition, microstructure, and surface morphology of these films have been characterized. In comparison to bulk steel sheets with the same chemical composition they have a smaller grain size and a ferritic structure. In contrast to bulk steel sheets they don`t contain any nonmetallic inclusions like Mn-sulfides. The influence of these structural differences on the corrosion resistance has been studied. For this purpose the electrochemical properties of the sputter-deposited steels have been compared ...

International Nuclear Information System (INIS)

Structure of ferrite in drawn pearlitic steel containing 0.9 mass% C was investigated with X-ray diffraction technique using synchrotron radiation. In the detailed analysis of diffraction peaks of ferrite during the drawing process, it was experimentally revealed that the transformation of ferrite from bcc to bct due to the supersaturation of carbon in ferrite of heavily drawn pearlitic steel.

Energy Technology Data Exchange (ETDEWEB)

Azobenzene dyes are effective inhibitors for austenitic 304 L and 316 L stainless steel corrosion in high acidic medium up to 7N. A good efficiency is obtained from weight loss and electrochemical Rsub(p) measurements in hydrochloric acid, while no inhibition is observed in sulfuric solutions. Transformation from the primarily azobenzene to other compounds give rise to enhanced protection of steel samples, and probable structures of the inhibiting species are proposed in view of our results.

International Nuclear Information System (INIS)

Paper estimates the corrosion resistance and studies the character of dissolving of silicon-bearing austenite stainless steels in strongly oxidizing media containing phosphate and fluoride admixtures. Corrosion behaviour of the studied steels is determined to depend essentially on the content of admixture or alloying silicon, as well as, on their phase composition in many respects determined by the thermal treatment condition. Refs. 22, figs. 1, tabs. 2.

International Nuclear Information System (INIS)

Pitting corrosion is a kind of electrolytic corrosion by which the surface of a material is locally affected owing to inhomogeneities on the part of the material or medium. The paper deals briefly with questions relating to the importance, to parameters medium or materialwise, influence on production and construction, as well as the general conditions for pitting corrosion. In particular oxygen corrosion in unalloyed and low-alloy steel, and pitting corrosion in ferritic chromium-steel and austenitic chromium-nickel (molybdenum) steel is described. (DG).

Energy Technology Data Exchange (ETDEWEB)

The use of nickel alloys in Flue Gas Desulfurization (FGD) applications is described. Recently, nickel alloys 625 and C-276 have been clad to carbon steel plate. Production and properties of the clad plate are reviewed and a brief discussion is presented on production, fabrication and welding. Laboratory and field corrosion tests in SO/sub 2/ scrubber environments suggest that alloy 625 and C-276 clad steel plates are as corrosion resistant as the solid alloy plate.

Energy Technology Data Exchange (ETDEWEB)

A number of properties in steel components are detrimentally influenced when exposed to hydrogen environments. Under these conditions, atomic hydrogen is adsorbed on the steel surface, then absorbed and preferentially transported towards tri-dimensional stressed regions in the crystal lattice and into defects such as interfaces or dislocations. The hydrogen embrittlement susceptibility is strongly influenced by various microstructural parameters including the type of inclusions, steel composition and heat treating conditions. One of the alternatives employed in minimizing hydrogen embrittlement is the use of surface barriers for hydrogen permeation. In particular, the presence of surface nitride layers in steels can be considered as an effective barrier. Nitride steel surface layers can be produced by plasma nitriding with the concomitant benefits of improved surface hardness, as ...

Energy Technology Data Exchange (ETDEWEB)

Discussion is presented of world crude steel production, the Japanese steel industry and its expectations of the Canadian coal industry. It is concluded that the Canadian coal industry should pay attention to the trend in customer's requirements regarding coal quality, maintain price competitiveness in the international market place, and remain flexible with regard to the market trend.

International Nuclear Information System (INIS)

Effect of hydroxide nature, concentration and temperature on corrosion resistance of domestic steels and alloys to hot NaOH, KOH, LiOH solutions is considered. It is ascertained that by corrosion growth in relation to stainless steels and nickel alloys, the hydroxides are placed in the following sequence: LiOHsteel and nickel alloy tendency to cracking is manifested, are determined. 12 refs., 12 figs.

International Nuclear Information System (INIS)

Duplex stainless steels are widely used in severe corrosion environments because of their good corrosion performance. This paper deals with the influence of aging treatments on the intergranular corrosion (IGC) resistance of a commercial duplex stainless steel, SAF 2205. Duplex stainless steel was given aging treatments in the range 773-1173 K for time periods ranging from 6 min to 100 h. Optical microscopy and XRD was carried out on the aged stainless steels for the microstructural study. The aged samples were evaluated for the IGC susceptibility with the ASTM standard practices. Potentiodynamic cyclic polarization studies were also carried out to investigate the influence of aging treatments on the passivity breakdown. The results indicate that the sigma phase gets precipitated and is responsible for grain boundary attack. (author).

British Library Electronic Table of Contents (United Kingdom)

Scuffing damage is catastrophic and typically not self-healing. It severely affects the life and reliability of engineering components, such as cams, roller bearings, piston rings, cylinder bores and gears. Gray iron and 1080 steel are important materials for these extremely demanding structural components. There have been several scuffing studies done in the past with various types of steel and cast iron. However, in these studies there was no attempt to compare the scuffing resistance of cast iron and steel materials with similar matrices. In the present study, scuffing tests were performed with the matrices of gray iron and 1080 steel being fully pearlitic. This allows for a direct evaluation of the effect of the graphite flakes on scuffing resistance. The scuffing behavior for these ma...

Energy Technology Data Exchange (ETDEWEB)

The goal of this project was to increase the high-temperature strength of the H-Series of cast austenitic stainless steels by 50% and the upper use temperature by 86 to 140 degrees fahrenheit (30 to 60 degrees celsius). Meeting this goal is expected to result in energy savings of 35 trillion Btu/year by 2020 and energy cost savings of approximately $230 million/year. The higher-strength H-Series cast stainless steels (HK and HP type) have applications for the production of ethylene in the chemical industry, for radiant burner tubes and transfer rolls for secondary processing of steel in the steel industry, and for many applications in the heat treating industry, including radiant burner tubes. The project was led by Duraloy Technologies, Inc., with research participation by Oak Ridge National Laboratory (ORNL) and industrial participation by a diverse group of companies.

International Nuclear Information System (INIS)

An Ultra-Low-Carbon 19% Cr-11% Ni Stainless Steels used in nuclear fuel reprocessing plants where highly corrosion resistance in nitric acid is required has been developed. This steel has optimized the chemistry composition to decrease inclusions and deformation-induced martensitic transformation. The formation of deformation-induced martensite has the potential danger of accelerating corrosion in nitric acid. In this paper, effects of cold reduction and martensitic transformation on corrosion resistance of Ultra-Low-Carbon Stainless Steels in nitric acid are discussed. The developed steel showed excellent corrosion resistance during long-term exposure to nitric acid. (author).

British Library Electronic Table of Contents (United Kingdom)

A ferritic steel with finely dispersed precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersed TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation ...

Energy Technology Data Exchange (ETDEWEB)

By retrofitting the existing steam turbine dual purpose power plant with a gas turbine plant and a secondary waste heat boiler the Technische Werke Ludwigshafen AG have considerably improved the energy generation in energetic, economic and ecological terms. The extension of the existing system to a combined cycle process has lead to this positive effect. The erection of a boiler plant during the first two construction phases has fully met the optimistic expectations. (orig.) [Deutsch] Mit der Nachruestung eines vorhandenen Dampfturbinen-HKW um eine Gasturbinenanlage mit nachgeschaltetem Abhitzekessel haben die Technischen Werke Ludwigshafen AG ihre Energieerzeugung entscheidend in energetischer, oekonomischer und oekologischer Sicht optimiert. Insbesondere die Erweiterung des vorhandenen Systems zu einem GuD-Prozess fuehrt zu dieser positiven Bilanz. Die Errichtung der Kesselanlage in den ersten beiden Bauabschnitten hat die optimistischen ...

Energy Technology Data Exchange (ETDEWEB)

The following industrial-scale power station processes are compared with natural gas/light fuel oil heating: Conventional steam generation, steam generation with gas turbine upstream, gas turbine process with low-pressure-waste heat boiler and cogeneration. Industrial gas turbines between 10 and 25 MW are compared with one another; typical boilers and industrial turbines are described. CO{sub 2} and NO{sub x} emissions are indicated. The steam turbines used are the efficient and robust turbines used in industry, wherever possible they are built as single-line plant with the gas turbine. (orig.) [Deutsch] Es werden folgende Industriekraftwerksprozesse mit Erdgas-Leichtoelfeuerung verglichen: Konventioneller Dampfprozess, Dampfprozess mit Vorschaltgasturbine, Gasturbinenprozess mit ND-Abhitzekessel und Kombianlage. Die Industriegasturbinen zwischen 10 und 25 MW werden gegenuebergestellt und typische Kessel und Industrieturbinen vorgestellt. ...

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional mathematical model has been developed as a tool for furnace structure design and operation conditions optimization when the straw combustion is in oxygen-enriched or conventional air atmospheres. Mathematical methods have been used based on a combination of FLIC (A fluid Dynamic Incinerator Code) code for the in-bed incineration and commercial software FLUENT for the over-bed combustion. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressures and temperatures, which is reflected by very low residual amounts of organic combustion by-products in the bottom ash and flue gas of the straw-fired boiler unit. The predictions indicated that the maximum combustion temperature is around 1500 K, CO emission is 201 vppm and O{sub 2} concentration is about 6.9 vol% at furnace exit, and it is shown that mathematical models can serve as a reliable tool for detailed analysis of straw combustion processes ...

International Nuclear Information System (INIS)

The following conclusions are drawn from the study of the effects of dissolved oxygen on corrosion denting: 1) Following the ingress of fresh-water contamination into a PWR boiler, an acidic chloride solution can be formed in the crevice between tube and tube support plate when an oxidant such as dissolved oxygen or copper ions is present in the boiler water. 2) In the absence of copper, very high levels of dissolved oxygen and neutral chloride are necessary to initiate corrosion. 3) When copper is present in the feed system, sufficient copper ions to initiate corrosion within the crevice are released when the chloride concentration is 0.8 mg/kg and probably also at lower chloride values. Corrosion initiation however may require prior exposure of the copper to dissolved oxygen and can be suppressed by pretreatment with hydrazine. 4) The effect of dissolved oxygen on corrosion already occurring was not explored; neither was the effect of ...

International Nuclear Information System (INIS)

A high-performance power system (HIPPS) is being developed. This system is a coal-fired, combined-cycle plant that will have an efficiency of at least 47 percent, based on the higher heating value of the fuel. The original emissions goal of the project was for NOx and SOx to each be below 0.15 lb/MMBtu. In the Phase 2 RFP this emissions goal was reduced to 0.06 lb/MMBtu. The ultimate goal of HIPPS is to have an all-coal-fueled system, but initial versions of the system are allowed up to 35 percent heat input from natural gas. Foster Wheeler Development Corporation is currently leading a team effort with AlliedSignal, Bechtel, Foster Wheeler Energy Corporation, Research-Cottrell, TRW and Westinghouse. Previous work on the project was also done by General Electric. The HIPPS plant will use a high-Temperature Advanced Furnace (HITAF) to achieve combined-cycle operation with coal as the primary fuel. The HITAF is an atmospheric-pressure, pulverized-fuel-fired ...

Energy Technology Data Exchange (ETDEWEB)

Options for successfully using biogas depend on project scale. Almost all biogas from anaerobic digesters must first go through a gas handling system that pressurizes, meters, and filters the biogas. Additional treatment, including hydrogen sulfide-mercaptan scrubbing, gas drying, and carbon dioxide removal may be necessary for specialized uses, but these are complex and expensive processes. Thus, they can be justified only for large-scale projects that require high-quality biogas. Small-scale projects (less than 65 cfm) generally use biogas (as produced) as a boiler fuel or for fueling internal combustion engine-generators to produce electricity. If engines or boilers are selected properly, there should be no need to remove hydrogen sulfide. Small-scale combustion turbines, steam turbines, and fuel cells are not used because of their technical complexity and high capital cost. Biogas cleanup to pipeline or transportation fuel specifications is ...

Energy Technology Data Exchange (ETDEWEB)

Nitrogen has been added to stainless steels to improve mechanical strength and corrosion resistance. High nitrogen steel production is limited by high gas pressure requirements and low nitrogen solubility in the melt. One way to overcome this limitation is the addition of nitrogen in solid state because of its higher solubility in austenite. However, gas and salt bath nitriding have been done at temperatures around 550 C, where nitrogen solubility in the steel is still very low. High temperature nitriding has been, thus proposed to increase nitrogen contents in the steel but the presence of oxide layers on top of the steel is a barrier to nitrogen intake. In this paper a modified plasma nitriding process is proposed. The first step of this process is a hydrogen plasma sputtering for oxide removal, exposing active steel surface improving nitrogen pickup. This is ...

Energy Technology Data Exchange (ETDEWEB)

The surface of low alloy steel (En40B) has been engineered in the plasma of a glow discharge via plasma nitriding and ion plating of titanium nitride (TiN) coatings on the nitrided substrates with the purpose of enhancing the surface properties and fatigue strength. The nitriding response of the steel has been accessed by the evaluation of phase composition, layer thickness, hardness profile, residual stresses and nitrogen and carbon distributions. The wear and fatigue characteristics of the plasma-nitrided steel have been investigated and simple models have been developed to describe the influence of such properties as depth and strength of the nitrided case on the fatigue limit and load-bearing capacity of the nitrided steel. In order to further improve the tribological properties and load-bearing capacity of the low alloy steel, a duplex plasma surface-engineering technique has ...

Energy Technology Data Exchange (ETDEWEB)

A procedure and correlations are presented for predicting Charpy-impact energy, tensile flow stress, fracture toughness J-R curve, and J{sub IC} of aged cast stainless steels from known material information. The ``saturation`` impact strength and fracture toughness of a specific cast stainless steel, i.e., the minimum value that would be achieved for the material after long-term service, is estimated from the chemical composition of the steel. Mechanical properties as a function of time and temperature of reactor service are estimated from impact energy and flow stress of the unaged material and the kinetics of embrittlement, which are also determined from chemical composition. The J{sub IC} values are determined from the estimated J-R curve and flow stress. Examples of estimating mechanical properties of cast stainless steel components during reactor service are presented. A common ``lower-bound`` J-R ...

International Nuclear Information System (INIS)

Ferritic/martensitic steel, modified 9Cr-1Mo steels have been used most extensively in the power generation industry throughout the world due to having superior high temperature properties such as high strength, creep resistance, and good microstructure stability. These steels are also the primary candidate for the RPVs(Reactor Pressure Vessels) of High Temperature Gas-Cooled Reactors. Currently, many studies has been conducted in laboratory-scale for mod. 9Cr-1Mo steels. However, there is a lack of the study on forged thick- section for RPVs. The differences in characteristics including the through thickness microstructure and mechanical properties between internal and external locations may occur during cooling after austenitization, because the thickness of RPVs is over about 200mm. Therefore, in order to use ferritic/martensitic steel as RPVs, a detailed assessment of the ...

Energy Technology Data Exchange (ETDEWEB)

In the course of this year six local exchange offices with alternative heating and hot water plants were started up in Switzerland. They are all of the same building type, designed for not more than 1000 telephone subscribers and for the same architectural conditions. However, the buildings are situated in different areas of the country and are thus subject to different environmental conditions. Solar collectors supplemented by electricity boilers are fitted to two of these objects. Heat pumps are operated in two other exchange offices while the last two are equipped with electric heating devices. For purposes of comparison two new test plants of the same size with oil heating devices are set up.

Energy Technology Data Exchange (ETDEWEB)

This paper describes the design, operation, and performance of an HVAC system installed as part of a project to demonstrate energy efficiency and environmental responsibility in commercial buildings. The systems installed in the 2180 m{sup 2} office building provide superior air quality and thermal comfort while requiring only half the electrical energy of conventional systems primarily because of the hydronic heating and cooling system. Gas use for the building is higher than expected because of longer operating hours and poor performance of the boiler/absorption chiller.

International Nuclear Information System (INIS)

In PWR steam-generators, the crevice between tube and tube-support plate tends to fill with porous deposits during operation and acts as a concentration site for chemicals in the boiler water, which may lead to corrosion of the tube and tube-support-plate. The rate of concentration, the magnitude of the concentration factor and the rate of release of solute when conditions change are important parameters for devising strategies to minimize corrosion. Values of these parameters for salt concentration have therefore been measured in a laboratory simulation of the crevice and are used to formulate a model of the concentrating process.

Energy Technology Data Exchange (ETDEWEB)

Combined heat and power (CHP) or cogeneration is the sequential production of two forms of useful energy from a single fuel source. In most CHP applications, chemical energy in fuel is converted to both mechanical and thermal energy. The mechanical energy is generally used to generate electricity, while the thermal energy or heat is used to produce steam, hot water, or hot air. Depending on the application, CHP is referred to by various names including Building Cooling, Heating, and Power (BCHP); Cooling, Heating, and Power for Buildings (CHPB); Combined Cooling, Heating, and Power (CCHP); Integrated Energy Systems (IES), or Distributed Energy Resources (DER). The principal technical advantage of a CHP system is its ability to extract more useful energy from fuel compared to traditional energy systems such as conventional power plants that only generate electricity and industrial boiler systems that only produce steam or hot water for process applications. By using ...

International Nuclear Information System (INIS)

Existing applications of Alloy 800 are summarized, with particular reference to its use in various types of reactor. The need for a co-ordinated research and development programme is stressed, and the variables to be explored are outlined. The papers relating to the problem of corrosion and cracking in water and steam are considered. the strength and ductility of Alloy 800 is considered. Finally, sections of the summary deal with the use of Alloy 800 for (a) sodium cooled fast reactor boiler tubes; (b) the high temperature gas cooled reactor; and (c) PWR steam generator tubes. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

Three systems for the heat supply in the built environment have been compared for the costs, the energy consumption and emissions of CO{sub 2}, NO{sub x} and SO{sub 2}. The heating systems compared are based on central heating boilers, district heating systems in combination with combined steam and gas turbine cycles, and heating by means of several gas engines. From the results it appears that the boilers demand the lowest investments. The district heating systems are more expensive. Both heating systems, however, show considerable savings of energy (55 to 70%). The exploitation costs depend strongly on the fuel price scenarios used and the assumptions with regard to interest and inflation. The emissions of CO{sub 2} are also considerably lower for both combined heat and power generating systems. The use of gas engines results in higher acidifying emissions compared to the system with the central heating boilers, and lower ...

International Nuclear Information System (INIS)

Since 1984 the thermal-hydraulic code ATHLET has been also applied for the analyses of LOCA and transients in VVER plants. The specific design of these plants especially of the steam generator design requires a specific modelling of the phenomena which may occur under LOCA and transient conditions in these plants. Differences in design compared to the design of western reactors have been briefly listed. Specific phenomena occurring under small leak accidents are shortly described. The consideration of the simulation of the boiler-condenser mode illustrates the modelling requirements for a code which may be applied to the prediction of such a thermal-hydraulic behaviour. Facing the lack of experimental data, the reliability of the simulation has been discussed by means of plausibility studies based on the momentum balance for steam and water. In summary: The VVER reactors differ in design compared to reactors of western design. The VVER design, especially the design ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical dissolution behaviour of armco-iron and of the steels C15, C45, C60 and 100Cr6 in concentrated sodium chloride media has been investigated. Anodic metal dissolution experiments have been carried out using the flow channel cell (parallel plate reactor), the rotating cylinder electrode (RCE) and the capillary cell. The microstructure of the steel has been varied through variation of carbon content and heat treatment (e.g. soft annealed with globular carbides or pearlitic). Current-efficiency values have been obtained by gravimetric measurements in the current-density range from i=5 to 60 A/cm{sup 2}. For the soft annealed steels, the divalent ferrite dissolution in combination with electroless cementite removal dominates. For the pearlitic steels, the occurrence of oxygen evolution electronically conductive metal carbides or trivalent ferrite dissolution, depending on the current ...

Energy Technology Data Exchange (ETDEWEB)

The wear behaviour of 722M24 (En40B) steel plasma nitrided at high temperatures for long durations was investigated. Under dry sliding and abrasive-containing lubricated conditions, the wear characteristics of the steel were studied as a function of load, time and white layer thickness. The white layer and the wear debris were characterized by X-ray diffraction. The topography of the wear surface was examined in a scanning electron microscope. The plasma nitriding process was carried out using a 20 kW plasma processing unit in cracked ammonia atmosphere. Treatment times of up to 100 h were employed with temperatures of 550, 570 and 590 C. Wear tests were performed with plasma nitrided AMS 6472 as the counterface material. The tests under abrasive-containing lubricated conditions were carried out with 10% carborundum powder 10 [mu]m in size in SAE-30 machine oil. The wear resistance of the steel was improved by plasma ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes an investigation of electrodeposited Zn-14% Ni and aluminium-based SermeTel 1140/962 coatings as possible replacements for cadmium. Slow strain rate tests were performed to measure the extent of direct hydrogen embrittlement of a high strength steel substrate as a result of the coating process and of hydrogen re-embrittlement caused by coating corrosion. The level of re-embrittlement was shown to depend on both the electrochemical potential of the coating and its barrier properties. Zn-14% Ni coatings caused the most re-embrittlement as they had the most active potential and contained through-thickness defects which left the steel exposed to hydrogen uptake. The microstructure of the high strength steel was also shown to be an important factor affecting the extent of embrittlement. AerMet 100 steel was more resistant than 300M steel and this was attributed to ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, the state-of-the-art ultrasonic and magnetic measuring techniques developed at Kawasaki Steel and used in the production process of steel sheets are described. Representative examples shown here are as follows: (1) Magnetic flux leakage testing system for the detection of nonmetallic inclusions, (2) Nondestructive orientation measurement for secondary re-crystallized grains in grain-oriented electrical steel by ultrasonic interferometry, (3) Immersion testing method for the detection of nonmetallic inclusions, (4) Surface wave probe for the detection of surface flaws in rolls used in rolling mills. Developments of these techniques and their applications to actual steel sheets production processes have contributed to advance in technologies for quality assurance and control. With the help of these techniques, steel sheet products with advanced and uniform properties ...

International Nuclear Information System (INIS)

Because of their austenitic-ferritic microstructures, duplex stainless steels offer a good combination of mechanical and corrosion resistance properties. However, heat treatments can lower the mechanical strength of these stainless steels as well as render them susceptible to intergranular corrosion (IGC) and pitting corrosion. In this study, a low-carbon (0.02%) duplex stainless steel is subjected to various heat treatments at 450 to 950 C for 30 min to 10 h. The heat-treated samples than undergo ASTM IGC and pitting corrosion tests, and the results are correlated with the microstructures obtained after each heat treatment. In the absence of Cr_2_3C_6 precipitation, #sigma#-phase precipitates render this duplex stainless steel susceptible to IGC and pitting corrosion. Even submicroscopic #sigma#-phase precipitates are deleterious for IGC resistance. Longer-duration heat treatments (at 750 to 850 C) ...

International Nuclear Information System (INIS)

Separate effect of impurities and alloying additions of phosphorus, silicon, boron, carbon, sulphur, magnesium, copper, aluminium and molybdenum on the tendency to intergranular corrosion (IGC) of quenched highly pure steel Fe-20% Cr-20Ni in boiling solution 27% HNO_3+40 g/l Cr"6"+, as well as in sulphuric and nitric acids mainly at potentials, corresponding to repassivation range, has been studied. It is shown that steel susceptibility to IGC depends on impurity nature and to a high extent is determined by the potential value independent of the way of its achieving. The most unfavourable effect on stability of grain boundaries is produced by microadditions of boron as well as by impurities of phosphorus and silicon. To ensure increased corrosion resistance of the investigated steel against IGC in highly oxidative media the pontent of phosphorus and silicon impurities unit should not exceed 0.01 and 0.2% respectively. At ...

Energy Technology Data Exchange (ETDEWEB)

Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation ...

Energy Technology Data Exchange (ETDEWEB)

Inhibition efficiency of some water-soluble hydrazones for C-steel corrosion in hydrochloric acid has been tested by weight loss, polarisation measurements and open circuit technique. The inhibition effect was attributed to the adsorption of the additives on the C-steel surface as supported by adsorption measurements at Pt electrode using cyclic voltammetry. Electrochemical measurements indicated that all the additives behave as cathodic-type inhibitors. The data obtained fit well to both the Temkin adsorption isotherm and the kinetic-thermodynamic model. The inhibition behaviour and its order were explained with the help of the proposed skeletal representation.

International Nuclear Information System (INIS)

The low alloy steels were nitrided in the plasma atmosphere generated by using hollow cathode discharge. For comparison, specimens of 40 Cr steel were in two different potential states. One kind is isolated from cathode and anode between them the discharge was created. The other kind is placed on the plate which is connected to the cathode. The nitriding was carried out at different temperatures. The surface morphology, phase of compound layers and microhardness profiles were analyzed. The optical microscopy observation and X-ray diffraction showed that the compound layers were formed in all experiments. The results of the nitriding treatment are weakly dependent on the potentials applied on the specimens.

Energy Technology Data Exchange (ETDEWEB)

Once again residual austenite as one component of the microstructure of steels is the basis for discussion among experts. Very often the phenomen of the stabilisation of residual austenite is the focus of interest. In this paper the influence of ageing on residual austenite transformations is discussed, with ageing taking place in a temperature range between ambient and M/sub s/-temperature after quenching from different austenitizing temperatures by means of subzero refrigeration. Results which are typical for 100Cr6 steel are presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

Voestalpine AG (Linz, Austria) produces heavy steel for steam turbines, compressors for the promotion of oil and gas as well as for the chemical industry, mechanical engineering and for the offshore technology. A weight range between 1 and 200 tons can be covered. The author of the contribution under consideration is limited to characteristics which have to be managed by a large steel foundry within the range of the steam power plants. This is described on the basis of produced steam turbines for power stations in the highest performance segment (1,600 MW).

International Nuclear Information System (INIS)

This paper deals with the pitting corrosion of evaporators in the liquid - radwaste system of nuclear power stations. Corrosion testrs were conducted by the anodic polalization of specimen in the chloride solution. (1) The initiation of the pitting in SUS 304, SUS 316 stainless steels was inhibited by addition of NaOH and H_3BO_3, however, these addition had no effect on the pitting propagation. (2) Inconel 625 had the resitivity against the pitting initiation superior to that of stainless steels, but this was not necessarily in the case of the pitting propagation. (3) It is noticed for pitting prevention that the environmental and material effect on the pitting initiation differed from that on the pitting propagation. (author).

Energy Technology Data Exchange (ETDEWEB)

The effect of aging on the microstructure and tensile properties of a type 316LN stainless steel/Alloy 800 joint, welded with 16-8-2 stainless steel consumable, has been studied to characterize and evaluate the joint for long-term elevated temperature service. The joint was subjected to accelerated againg heat treatments at 873 K up to 5000 h to simulate long-term service exposures. Analysis of the results from this investigation shows that this joint has adequate stability of microstructure and tensile properties even after prolonged exposure at elevated temperatures. (orig.)

Science.gov (United States)

Three bonding agents were evaluated to determine which were most effective in enhancing the bond of resin composite to stainless steel. A light-activated resin composite was bonded to a total of 60 stainless steel specimens using Panavia, Cover-Up, or Silicoating. Tensile bond strength measurements revealed that all three agents provide a satisfactory means of increasing adherence of the esthetic veneer without decreasing bonding through thermocycling of the specimens. Panavia and Cover-Up were significantly more effective than Silicoating and appear to be easier to use. PMID:8297460

Science.gov (United States)

The Asarco-Mission complex (image left) is an active producer of copper and molybdenum (important in making steel and other metal alloys), ...

British Library Electronic Table of Contents (United Kingdom)

Irradiation of EP-823 (16Cr12MoWsiVNbB) ferritic-martensitic steel with 7-MeV Ni++ ions and with 30- and 70-keV He+ ions at a temperature of 500?C was followed by an increase in the microhardness, which was due to both radiation point defects and changes in the phase composition and the dislocation structure of the steel. It was found that the dependence of the largest relative increase in the microhardness on the concentration of radiation-induced point defects in the near-surface region of the steel under irradiation with different ions correlated with an analogous dependence of the surface segregation of silicon and chromium.

Science.gov (United States)

... 36 7 Corrugated Steel Pipe Concept Layout--Elevation ..... 37 viii ... revetment. 3. Land Use ... Corner modules and capping blocks are available. ...

UK PubMed Central (United Kingdom)

A survey was carried out in a steel foundry in Brisbane to evaluate the nature and frequency of respiratory symptoms and to assess ventilatory function. The foundry used many moulding processes including...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this article a production method of a magnetorheological suspension composed with silicon steel particles of size 0.1-0.15 mm and 4% silicon content is described. Steel particles were dispersed in a conducting carrier of a by mixture of graphite particles with size 2-5 {mu}m and cedar wood oil. The filling factor of the suspension with the silicon steel particles and with graphite particles amounted to 0.25-0.40. Samples of this suspension were placed in a rectangular vessel with electrodes and used for the investigation of the Hall effect in magnetic field with induction 0-8 T, generated by Bitter-type magnet. A non-linear dependence of Hall voltage on the induction of the applied magnetic field and a hysteresis loop of this voltage in the shape of inclined digit eight were found. The causes of the observed effects is the ordering of silicon steel particles and graphite particles along the side of ...

British Library Electronic Table of Contents (United Kingdom)

On the basis of a numerical model, the temperature and liquid fraction of spray-formed H13 tool steel are calculated as a function of time. Results show that a preheated substrate at the appropriate temperature can lead to very low porosity by increasing the liquid fraction in the deposited steel. The calculated cooling rate can lead to a microstructure consisting of martensite, lower bainite, retained austenite, and proeutectoid carbides in as-spray-formed material. In the temperature range between the solidus and liquidus temperatures, the calculated temperature of the spray-formed material increases with increasing substrate preheat temperature, resulting in a very low porosity by increasing the liquid fraction of the deposited steel. In the temperature region where austenite decomposit...

International Nuclear Information System (INIS)

Denting phenomenon as experienced in PWR steam generators has been investigated in the laboratory of Monel-400 tubes and C-steel baffles combination. Isothermal corrosion tests have been carried out by exposing capsules, containing a crevice between Monel-400 tubes and C-steel plugs, in plausible corrodents at 300"0C. Results indicated that the denting phenomenon is strongly influenced by the chloride content in the solution. In addition, it is a time dependent process. Stress exerted on the tubes by the growth of corrosion product on the outside surface of C-steel plugs are enough to deform the Monel tubes. The results have been discussed on the basis of accelerated corrosion of C-steel by hydrolyzable metal chlorides. (author).

Energy Technology Data Exchange (ETDEWEB)

The electrochemical metal dissolution of 100Cr6 steel in sodium chloride solution, applying high electrolyte flow rates and high current densities, has been studied with a view to the influence of material heterogeneities such as carbide segregation lines in the steel matrix. It was shown that the presence of such segregations is responsible for the formation of troughs on the specimen surface during electrochemical dissolution. A mechanism for trough formation was proposed. A dedicated heat treatment applied to the 100Cr6 steel eliminated the carbide segregation lines and established a soft annealed, fine-grained microstructure containing globular carbides. Subsequent electrochemical dissolution did not show any development of surface irregularities as troughs. (orig.)

International Nuclear Information System (INIS)

German (Dec 1973). Germany Carlen, JC Blom, U. Sandvik Steel Works,

International Nuclear Information System (INIS)

Japanese Sep 2009 p. 103-106 Japan Idota, Yasuhiro Inoue, Hiroyuki

Energy Technology Data Exchange (ETDEWEB)

This report summarizes some experiences gathered when using the semi-empirical temperature model that forms the heart of the steel casting advisory system `TUNDTEMP` in simulating the casting process. The model estimates the evolution of the liquid steel temperature in a tundish of a continuous casting machine through a temperature prediction at a couple of central time instants during the casting process. The results are compared with corresponding actual observations during the castings - measured steel temperatures and recorded casting difficulties and interruptions. Explanations for the possible discrepancies are suggested. Starting from a heuristically chosen set of model parameter values, some developing steps have been tested to reduce the simulation errors. The study concentrates mainly on temperature predictions for single heat castings. At the end of the report, some simulations of sequence castings are also ...

British Library Electronic Table of Contents (United Kingdom)

Flue gas desulfurization systems (FGDs) are operated in severely corrosive environments that cause sulfuric acid dew-point corrosion. The corrosion behavior of low-alloy steels was tested using electrochemical techniques (electrochemical impedance spectroscopy, potentiodynamic tests, potentiostatic tests), and the corrosion products were analyzed by scanning electron microscopy and X-ray photoelectron spectroscopy. The electrochemical results showed that alloying W with small amounts of Sb, Cu, and Co improves the corrosion resistance of steels. The results of surface analyses showed that the surface of the steels alloyed with W consisted of W oxides and higher amounts of Sb and Cu oxides. This suggests that the addition of W promotes the formation of a protective WO3 film, in addition to ...

International Nuclear Information System (INIS)

The effects of modification with Ti and Nb, heat treatment and solute segregation on void suppression in 316 stainless steel were studied using HVEM in the temperature range of 623-873 K after solution treatment at 1323-1473 K. Post-irradiation compositional analysis was performed by an energy dispersive X-ray analyzer. In Ti-modified stainless steel, void swelling peaks appeared at 723 K and 823 K. On the other hand, when the stainless steels modified by both Ti and Nb were irradiated, the void swelling was effectively suppressed, particularly the growth rate of a void was remarkedly retarded. This void suppression effect was easily recognized with increasing Nb concentration. Compositions such as Mo, Cr, Ti and Ni changed during irradiation and Ni, Si and Ti enriched around voids, whereas Cr and Mo depleted. (orig.).

International Nuclear Information System (INIS)

... Dozaki, Koji Takiguchi, Hideki Japan Atomic Power Company, Tokyo (Japan)

International Nuclear Information System (INIS)

The rate of corrosion of alloyed steels in solutions of orthophosphoric acid at the temperatures from 100 to 200 deg C has been ascertained by gravimetric method. It is shown that the 06Kh23N28MDT steel features the highest corrosion resistance, the second in terms of the characteristic mentioned is 08Kh22N6T, then - 10Kh17N13M2T, 08Kh21N6M2T, 12Kh18N9T. Corrosion rate of the steels studied intensifies at the acid concentrations exceeding 10% and increases essentially with the temperature increase. 6 ref., 2 tabs.

International Nuclear Information System (INIS)

Feb 2006 p. 80-84 Japan Mizuno, R. Matsuda, F. Japan Power Engineering

International Nuclear Information System (INIS)

Russian (Dec 1973). USSR Chmovzh, VE Lipshtejn, RA Zalkind, I.Ya. Dik,

Energy Technology Data Exchange (ETDEWEB)

This paper discusses the application of a Computational Fluid Dynamics (CFD) code (FLUENT) to predict temperature and velocity profiles, and particle trajectories in an industrial fired by a low NO{sub x} pulverized coal swirl burner. The predictions of the code were compared to experimental measurements of gas temperature, particle size distribution, and particle velocities. The diagnostics employed were a suction pyrometer and a Particle Counter Sizer Velocimeter Probe (PCSV-P). Good agreement was found between the temperature predictions and the measurements. In situ particle size distributions were predicted accurately using the Baum and Street model with a swelling factor of zero. The numerical modeling indicated that the Type II flow issued from the burner could be transformed into Type III flow, by eliminating swirl from the primary air stream, which provided the preferred particle trajectories and increased the combustion efficiency.

Energy Technology Data Exchange (ETDEWEB)

The nickel-rich superalloys Alloy 600 and Alloy 800 have been corroded in mildly alkaline deuterated aqueous conditions typical of secondary coolant circuits in a nuclear power station. The oxide films and substrates of these alloys have been analysed by imaging SIMS depth profiling, which makes it possible to describe elemental distribution in all three dimensions. The measurement of the distribution of the secondary ions NiO[sup -], FeO[sup -] and CrO[sup -] appears useful for detailing the behaviour of nickel, iron and chromium within oxidized phases. The measurement of D[sup -] distribution outlines the extent of oxide hydration. For Alloy 800, evidence of sodium migration into the grain boundaries of the alloy substrate is found. For Alloy 600, no grain boundary sodium ingress can be identified under comparable corrosion conditions. (author).

International Nuclear Information System (INIS)

In order to improve the reliability of PWR steam generators, we have performed research to improve the tubing material and tube-support-plate configuration, based on our wide operating experience, and have developed and verified Alloy TT690 as the optimum tubing material and the BEC (Broached Egg Crate) type tube-support design. In the research, we have studied the metallurgical mechanism of the alloy to improve its corrosion resistance, evaluated corrosion susceptible region quantitatively, estimated the actual environment in a steam generator and confirmed the reliability by a model boiler test over a long period. It has been verified that the steam generator with the latest design has higher reliability with respect to the corrosion resistance of tubes. (author).

British Library Electronic Table of Contents (United Kingdom)

Extraction of hemicellulose from hardwood chips prior to pulping is a possible method for producing ethanol and acetic acid in an integrated forest bio-refinery, adding value to wood components normally relegated to boiler fuel. Hemicellulose was extracted from hardwood chips using green liquor, a pulping liquor intermediate consisting of aqueous NaOH, Na2CO3, and Na2S, at 160degreeC, held for 110min in a 20L rocking digester. The extracted liquor contained 3.7% solids and had a pH of 5.6. The organic content of the extracts was mainly xylo-oligosaccharides and acetic acid. Because it was dilute, the hemicellulose extract was concentrated by evaporation in a thin film evaporator. Concentrates from the evaporator reached levels of up to 10% solids. Inhibitors such as acetic acid and sodium ...

Science.gov (United States)

An assessment study of the sea water scrubbing process for flue gas desulfurization has been made by SINTEF. This project has been financially supported by the Royal Ministry of Environment of Norway. The study is based on three FGD-units which are installed at three oil-fired, industrial boilers respectively with a maximum continuous heat input of 130 MW (27 MW + 2x51.5 MW) corresponding to approximately 50 MWE (10 MWE + 2x20 MWE) generating capacity for a power plant having a net efficiency of 38%.

Science.gov (United States)

Bechtel Power Corporation has performed an evaluation of flue gas desulfurization (FGD) system cost versus design level of operating availability for an industrial sized dual-alkali process. Two principle sources were used: the Flue Gas Desulfurization Information System (FGDIS) maintained by the Environmental Protection Agency and budget quotations from an FGD vendor. A survey of the FGDIS data base proved inconclusive in establishing a relationship between FGD system cost and operating availability. Using equipment failure rates derived from various sources, component availability factors were developed for all major FGD system components. Cost and availability data of nine industrial FGD system configurations were analyzed on a per boiler basis. Linear curve fitting of these data produced mathematical relationships of cost and availability.

Energy Technology Data Exchange (ETDEWEB)

The North Dakota Energy & Environmental Research Center (EERC) approach to removing NO{sub x} from flue gas emitted by coal-fired utility boilers or for the control of NO{sub x} formation by advanced combustion techniques involves the development of a catalytic fabric filter (CFF) for simultaneous NO{sub x} and particulate control. The NO{sub x}is removed by catalytic reduction with ammonia to form nitrogen and water. Bench-scale experimental results have shown that over 90% NO{sub x} removal can be achieved. This report details the strengths and areas for for development in this project.

Energy Technology Data Exchange (ETDEWEB)

The development of new steels is always a challenge for the manufacturer of filler metals. In many cases it is obvious that some properties of the base metal cannot be fulfilled with matching filler metals. In some cases, dissimilar filler metals can solve the problem in some cases, there is no chance to meet the requirements of the base metal (for example yield strengths of new ultra high strength steels). This paper deals with different kinds of new steels and the requirements for the weld metal with examples from motor car industry (Mangan Austenite), crane (Ultra high strength steels), earthmoving machinery (Wear-resistant steels) and offshore (Supermartensitic steels). Specific problems will be discussed and best solutions will be highlighted. These examples make clear that the success of new kinds of steels in the market depends on ...

Wastenet

... The composite ground floor is suitable for support to all types of wall construction and can be used equally well on strip footings or mini-pile foundations . The light steel edge beams provide the accurate template required for internal timber or light steel wall frames to minimise fitting time and eliminate rework. The floated slab surface will accept floor finishes directly and thermal insulation can be easily fitted beneath ...

Energy Technology Data Exchange (ETDEWEB)

In the area of seasonally thawing soil, porous or broken coatings cannot significantly retard the process of pile metal destruction, since it will occur through electroosmotic penetration of the base electrolyte to the metal surface. Such processes can be prevented by electrochemical protective methods. Systems based on grid cathode stations with power control and distribution units are recommended for use for cathode protection of steel pile foundations.

Energy Technology Data Exchange (ETDEWEB)

The study by impedance and photoelectrochemical measurements of passive films formed on an AISI 304 type stainless steel shows that important parameters of the electronic structure of these films are modified under ..cap alpha.. irradiation, namely: width of the space charge region, donors concentration and diffusion length for minority carriers. The consequences of ..cap alpha.. irradiation on localized corrosion processes are discussed.

Energy Technology Data Exchange (ETDEWEB)

This paper investigates the anodic behavior of steels 12Kh18N10T, 10Kh17N13M2T, 08Kh22N6T, and 08Kh21N6M2T in 92% sulfuric acid. The aim of the study was to determine the parameters for anodic protection of shell-and-tube coolers. Results of the study are presented.

Energy Technology Data Exchange (ETDEWEB)

To assist in attaining the HSE's objective of providing perspective and focus for Safety Case Assessment, a generic model of the structural design process for the foundations of pile supported fixed steel structures has been developed. Interfaces between the foundation design team and other stakeholders have been identified and assessments made of both the magnitude and the potential significance of the uncertainties associated with key elements of the design process. (author)

International Nuclear Information System (INIS)

By means of ESCA the composition and the thickness of passive films formed on austenitic stainless steels were investigated after the attack of nitric acid at various temperatures and acid concentrations. The outermost layers of the oxide film consist of SiO_2, then a layer rich of Cr-oxid follows, containing also some Mo in the four- and sixvalent state. Ni does not contribute to the oxide film. Cr is also enriched in the metal just below the oxide film. (orig.).

International Nuclear Information System (INIS)

The involvement and relationship of carbon steel corrosion products in the tube denting phenomenon promoted an intensive research effort to: 1) understand, reproduce, and arrest the denting process, and 2) evaluate alternative tube support materials to provide additional corrosion resistance. The paper summarizes a corrosion testing program for the verification of type 405 stainless steel under acid or all volatile treatment conditions.

Energy Technology Data Exchange (ETDEWEB)

Two austenitic steels, 316 Stainless Steel and Alloy 800, have been examined under conditions of both isothermal low cycle fatigue (LCF) and thermomechanical fatigue (TMF). The TMF tests were conducted between 649 and 360/sup 0/C with a carefully controlled triangular waveform. The LCF tests were performed at 649/sup 0/C and both kinds of tests were subjected to a strain range of 0.5%. TMF shortened life to 40% for 316 Stainless Steel and to 5% for Alloy 800. The microstructural evolution occurring in both alloys has been examined and we conclude these do not play a role in the life shortening caused by TMF. The TMF does produce asymmetric hysteresis loops with large tensile peak stresses in tests where the maximum temperature corresponded with the peak compressive stress. The influence of TMF on fatigue crack growth rates has been measured and it was found that TMF accelerated crack growth in Alloy 800 and slowed it down ...

International Nuclear Information System (INIS)

By using a plasma nitriding procedure at the PUPR Mirror Cusp Plasma machine, surface hardness is increased in 302/304-type stainless steel samples by exposing them to high-ion-density plasma at high vacuum. This method successfully dopes the surface of the material with strengthening nitrogen ions, without the use of chemical procedures that sacrifice the resistance to corrosion of the given material. A 500 V negative bias is placed on the sample exposed to the nitrogen plasma, where high-energy ions are therefore attracted and immersed into the metallic matrix microns into the surface of the stainless steel. This potential maintains a constant surface temperature at approximately 800 deg. C. The plasma parameters including ion density and plasma temperature were diagnosed using single Langmuir probes. The stainless steel samples were then tested using scanning electron microscopy (SEM), and Vickers micro-hardness testing ...

International Nuclear Information System (INIS)

In recent years intergranular stress corrosion cracking has occurred world-wide in the shrink-fitted discs of low pressure turbine rotors made of low alloy steels. Only in a few cases steam impurities such as NaOH, Na_2CO_3, Na_2SO_4, H_2S or NaCl, which initiate SCC, could be found. To clarify the SCC-behaviour experiments on turbine disc steels with different chemical compositions and yield strength were performed in high purity water. The results show, that chemical composition has no effect on the crack initiation. Under high purity water conditions no crack initiation due to stress corrosion cracking is observed on the steel with a yield strength of 850 N/mm"2. On the steel with a yield strength of 1250 N/mm"2 which is not used in service, crack initiation occurs in pure water. But if sharp cracks already exist, crack propagation occurs in both cases. The investigations showed, that stress ...

International Nuclear Information System (INIS)

The aim of this work is to describe the processes during plasma nitriding of Nb-containing, powder metallurgy prepared (PM) tool steel. PM steel was studied containing 2.5% C, 3.3% Si, 6.2% Cr, 2.2% Mo, 2.6% V, 2.6% Nb and 1.0% W, produced by melt atomization and hot isostatic pressing. The hardened and tempered steel was plasma nitrided at temperatures ranging from 470 to 530 deg. C. The nitriding time was 30-180 min. Optical microscopy, electron microscopy, XRD, EDS, WDS and hardness measurements were used to study the steel's properties, microstructure, phases and chemical composition. The nitriding temperature of 470 deg. C was found to be unsuitable for practical use because the layers prepared at this temperature were non-uniform. The compound layer formed by M_2_,_3(C,N) and M_4N was found after nitriding at temperatures of 500 and 530 deg. C for at least 60 min. The effect of niobium on the ...

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories is currently involved in the optimization of a Plane Shock Generator Explosive Lens (PSGEL). The PSGEL component consists of a detonator, explosive, brass cone and tamper housing. The purpose of the PSGEL component is to transmit a plane shock wave through the 4340 steel bulkhead (wave separator) which has a ferro-electric (PZT)ceramic disk attached to the opposite surface of the steel bulkhead. The planar shock wave depolarizes the PZT 65/35 ferro-electric ceramic to produce an electrical output. One aspect of the optimization program involves the possible replacement of 4340 steel with PH13-8Mo steel for the bulkhead. These materials, as well as the PZT 65/35 ferro-electric ceramic and the brass for the cone, required the stock characterization with respect to Hugoniot parameters. The work presented here gives the shock Hugoniot values for these four materials and ...

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately ...

International Nuclear Information System (INIS)

Fe-Ni-Mn martensitic steels are one of the major groups of ultra-high strength steels that have good mechanical properties and ductility in as annealed condition but they suffer from severe inter-granular embitterment after aging. In this paper, the effect of heavy shaped cold rolling and wire drawing on the mechanical properties of Fe-Ni-Mn steel was investigated. This process could provide a large strain deformation in this alloy. The total strain was #epsilon# #approx#7. Aging behavior and tensile properties of Fe-10Ni-7Mn were studied after aging at 753 K. The results showed that the ultimate tensile strength and ductility after cold rolling, wire drawing and aging increased up to 2540 MPa and 7.1 %, respectively, while the conventional steels show a premature fracture stress of 830 MPa with about zero ductility after aging.

International Nuclear Information System (INIS)

Neutron irradiation embrittlement of reactor pressure vessel (RPV) steels is one of the critical issues on aging management for long term operation of nuclear power plants. Mechanistic understanding of embrittlement is a key to accurate prediction of embrittlement, especially after long term operation where the mechanical test data are sparse. Since matrix hardening is the source of the embrittlement, we focus on matrix hardening of A533B bainitic pressure vessel steel. Bainitic matrix is composed of lath structure made by ferrite and carbides, therefore it is important to understand how this structure affects hardening behavior, and to understand irradiation response of each phase. As the typical dimension of lath structure of A533B is about one micron, nanoindentation technique is suitable for the estimation of hardening of each phase. MV ion accelerators were used for controlled irradiation because MeV ion irradiation can produce defects to ...

Energy Technology Data Exchange (ETDEWEB)

45{number_sign} steel, which has good mechanical strength and is relatively cheap, is a common constituent in industrial components, such as precision gears, piston columns of oil pumps, and so on. However, since the working environment of these industrial parts is sometimes quite harsh and unforgiving, they are vulnerable to wear and corrosion. Replacing 45{number_sign} steel with stainless or alloy steel increases the cost significant, and a better alternative is to improve its surface properties and lifetime using plasma immersion ion implantation (PIII). The authors have devised a variety of treatment processes using PIII, including radio-frequency (RF) plasma nitriding, RF plasma nitriding and nitrogen PIII, Ti deposition in conjunction with nitrogen PIII (IBED), as well as Cr deposition followed by nitrogen PIII (IBED). To assess the efficacy of the processes, the microhardness and mass loss due to wear were measured ...

Energy Technology Data Exchange (ETDEWEB)

The effect of microalloying with carbide-forming (V,Ti,Nb) and rare-earth elements and of high-temperature thermomechanical processing (HTMP) on the structure, mechanical properties and low temperature behaviour of 38CrSi steel has been investigated. It has been shown that in the case of dissolution of carbides during heating for quench hardening, the tempering resistance of the steel increases. It has also been found that - as a result of HTMP - the susceptibility of the steel irreversible temper brittleness decreases, irrespective of the steel having been microalloyed or not. The data, originating from tensile testing and impact testing (with the help of laser interferometry) in the temperature range from +20 to -196 degC, has been explained in terms of fractographic analysis. It has been shown that microalloying and HTMP favour the occurrence of ductile microvoids in the fracture. On the other hand, ...

International Nuclear Information System (INIS)

The adherent magnetite film thickness, corrosion rate and the loose crud on the surface of carbon steel and other structural materials were evaluated by inserting the coupons in the two autoclaves connected to the two ends of the PHT systems of Indian PHWRs. This paper includes an analysis of the results obtained during the hot conditioning of TAPP-3 and 4, Kaiga-3 and 4, and RAPP-5. The system temperatures of 230 deg C to 260 deg C and the adherent magnetic thickness of 0.30 ?m to 0.75 ?m on the internal surface of carbon steel were achieved during the hot conditioning of these reactors. The time duration of termination of the hot conditioning ranged from 48 to 71 hours. The maximum magnetite film thickness of 0.75 ?m in 71 hours and temperature 260 deg C and a minimum thickness of 0.30 nm in 48 hours at 230 deg C were achieved during hot conditionings. The XRD analyses of hot conditioned carbon steel coupons showed that ...

Energy Technology Data Exchange (ETDEWEB)

The most developed systems for the generation of electricity from coal are the Integrated coal Gasification Combined Cycle (IGCC) and the Pressurized Fluidized Bed Combustion (PFBC) system. They both represent state-of-the-art technology and provide electric power at 41-46% LHV efficiency. However, the high level of complexity leads to lower reliability and higher costs. A simpler system, based on a coal-fired steam boiler integrated with a gas turbine, has been proposed. In such a plant, known as the externally fired combined cycle (EFCC), compressed air is heated indirectly in a heat exchanger located in the coal furnace. The hot air is then expanded in a turbine, and the exhaust is passed on to the coal furnace as preheated combustion air. Steam produced in the boiler generates additional power in a steam turbine. The exclusion of coal combustion products from the gas turbine avoids hot gas clean-up and turbine blade corrosion by coal ash. ...

Energy Technology Data Exchange (ETDEWEB)

In China, the conventional utilization of oil shale is concentrated mainly on oil shale retorting, and burning oil shale in pulverized furnaces, or bubbling fluidized beds. To improve the availability of oil shale, many specialists have advocated burning oil shale in a circulating fluidized bed (CFB), which has a satisfactory combustion efficiency, low NOx and SO{sub 2} emission, adaptability to low-grade coal, etc. In Huadian, China, a plant incorporating three units of 65 th{sup -1} oil shale-fired CFB began successful commercial operation in 1996, proving that burning oil shale in a CFB produces both high combustion efficiency and environmental protection. For effective utilization of oil shale, its pyrolysis and combustion characteristics, emission performance of gaseous pollutants from an oil shale-fired CFB pilot setup, co-combustion characteristics of oil shale and high sulfur coal as well as the operating performance of the Huadian CFB boiler were further ...

Energy Technology Data Exchange (ETDEWEB)

This project, conducted under The United States Department of Energy (DOE) Cooperative Agreement DE-FC36-94GO10002/A002, was part of a multiple-phase effort to develop technologies that improve the energy efficiency and economics of chemical process recovery in the pulp and paper industry. The approach taken was to consider two major alternatives in two phases. Phase I, conducted previously, considered means to improve pulp mill recovery boilers using high-solids advanced combustion of black liquor; while this project, Phase la, considered means to recover kraft pulping mill process chemicals by low-temperature black liquor gasification. The principal steps previously proposed in this program were: (1) Evaluate these two technologies, high-solids advanced combustion and gasification, and then select a path forward using the more promising of these two options for future work. (2) Design and construct a pilot-scale unit based on the selected technology, and using ...

Energy Technology Data Exchange (ETDEWEB)

In this report is described the work effort performed to provide NETL with VE-Suite based Virtual Engineering software and enhanced equipment models to support NETL's Advanced Process Engineering Co-simulation (APECS) framework for advanced power generation systems. Enhancements to the software framework facilitated an important link between APECS and the virtual engineering capabilities provided by VE-Suite (e.g., equipment and process visualization, information assimilation). Model enhancements focused on improving predictions for the performance of entrained flow coal gasifiers and important auxiliary equipment (e.g., Air Separation Units) used in coal gasification systems. In addition, a Reduced Order Model generation tool and software to provide a coupling between APECS/AspenPlus and the GE GateCycle simulation system were developed. CAPE-Open model interfaces were employed where needed. The improved simulation capability is demonstrated on selected test problems. As part ...

Energy Technology Data Exchange (ETDEWEB)

Several shield options were analyzed for the ITER conceptual design to minimize the nuclear responses in the toroidal field (TF) coils. The total nuclear heating in the physics phase and the insulator dose in the technology phase are the most critical parameters in the design process. The first shield option has type 316 stainless steel and water shielding material. Steel and water also serve as structural material and coolant, respectively. The second option is similar to the first except that borated water is used instead of ordinary water. The other two options include a small layer of lead or boron carbide (B{sub 4}C) at the back of the shield. The last three shield options were considered to reduce the nuclear heating in the toroidal field coils relative to the steel/water shield. An optimization process was performed taking into consideration the thermal-hydraulics and the engineering requirements to define the shield ...

Energy Technology Data Exchange (ETDEWEB)

The high cost of proton exchange membrane fuel cells (PEMFCs) poses a significant challenges to their commercial uptake. The bipolar plates connect the anode and cathodes of cells and separate the reactant gases, and are the most expensive components in PEMFCs. Although stainless steel can be used as a low-cost alternative in bipolar plate construction, steel is prone to electrochemical corrosion in the highly acidic PEMFC operation process. This study examined the polarization curves and ICR as a function of compaction force of a high Cr and Ni austenitic stainless steel in an environment simulating the bipolar plate under PEMFC operating conditions. The 3-electrode system consisted of a platinum (Pt) sheet, a saturated calomel electrode with a Luggin capillary contract with the used solution and the work electrode. All polarization curves were measured in a solution of H{sub 2}SO{sub 4} in order to simulate the aggressive ...

International Nuclear Information System (INIS)

The design of the ITER primary first wall incorporates a multi-layered structure consisting of a layer of beryllium bonded to a layer of copper alloy with embedded stainless steel tubes which in turn is bonded to a stainless steel structure. In this configuration, the stainless steel provides structural support, the copper alloy improved resistance to high heat loads, and the beryllium layer a low Z metal interface with plasma. Fabrication, testing and control of this multi-layered structure, and indeed the entire blanket shield module, calls for advanced methods. Several associations in the four home teams and their industrial partners have been involved in various fabrication and joining tasks now grouped under L4 blanket project. In this paper, an overview of the work done so far for joining stainless steel to stainless steel, stainless steel to copper alloy, ...

Energy Technology Data Exchange (ETDEWEB)

As surface treated steel sheets, steel sheets with Zn-Fe coatings as well as double-layer steel sheets with Fe-P alloy coatings on Zn-Fe alloy coatings are often used practically. Two treatment methods, which are used to dissolve only alloy layers without dissolving steel sheets in order to find amount and composition of alloy layersr have already been reported. This report investigates the mechanisms of these methods, particularly the mechanisms to control dissolution of steel sheets. In the alkali-dissolution method, Zn-Fe alloy coatings are dissolved in a strong alkaline solution(NaOH-triethanolamine (TEA)-H{sub 2}O{sub 2}). In this case, steel sheets are insoluble because passive films are formed on the surface. In the cathodic polarization electrolysis method, alloy layers are electrolyzed({minus}l.2V) and dissolved in an ammonium nitrate-0-phen ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the major features of the advisory tool `TUNDTEMP`, developed to act as a decision support in the continuous steel casting process. `TUNDTEMP` provides a means to predict abnormal phenomena of temperature origin in the casting that may be difficult to foresee in practical situations. The heart of the system is a semi-empirical calculation model that yields an estimate of the evolution of the tundish temperature of the liquid steel on the basis of a few important casting factors. The user interface of the system is to a large extent based on the visual presentation of the simulated results. The system also contains an optional rule based mechanism that provides assistance in the result interpretation and, if wished, linguistically formulates action recommendations. A separate program has been built for the tuning of the calculation model and for maintenance of the system. At the end of the report, the different tuning ...

International Nuclear Information System (INIS)

In this paper, the influence of plasma nitriding at temperature 720 deg. C for 20 h on the surface microstructure and interface microstructure of electroplated chromium coating was investigated. In these conditions, interdiffusion, mixing and reaction phenomena of elements originating from the substrate and coating material are more likely to occur, thus increasing the bonding strength between the coating and carbon steel substrate. The change of the structures from the substrate side to the coating surface, and the effect of the substrate steel on the interface structure were studied by cross-sectional transmission electron microscope observation (XTEM). The nitride layer formed on the surface was analyzed by X-ray diffraction method (XRD). After treatment at above conditions a 6-7 #mu#m thick nitride compound layer was formed in surface region and the same thick carbide compound layer was also formed in the interface region between ...

British Library Electronic Table of Contents (United Kingdom)

Tailor die quenching in the hot stamping of quenchable steel sheets was developed to produce ultra-high strength steel formed parts having strength distribution. Local portions of the heated sheet were quenched by holding grooved tools at the bottom dead centre during the stamping. Non-contact portions were generated in the sheet by grooving the tools, and thus the strength in the contact portions is high owing to the quenching and that in the non-contact portions is low owing to the lack of the quenching. Hat-shaped products having a tensile strength of approximately 1.5GPa only at four corners were formed.

British Library Electronic Table of Contents (United Kingdom)

Plastic injection molds are an important economic sector due to the increasing use of injection molded plastic components. The selection of mold steel material, its processing conditions, and the way it is machined and hardened all have an impact on how it performs during use across its lifecycle for injection molding. For this study, injection molding conditions seen during high volume manufacturing were used to induce wear that would be typical during processing. A 50wt.% glass fiber reinforced Polybutylene Terephthalate (PBT) was used for the research. After 3000 injection operations, surface damage was found only on the steel used for the stationary half of the mold cavity and the corresponding surface of the molded parts. In contrast, the moving half showed no surface damage or increa...

British Library Electronic Table of Contents (United Kingdom)

For an ultrafine grain ferrite/cementite (UGF/C) steel, the Charpy impact energy was measured at temperatures from 373K to 4.2K, and tensile tests were carried out at temperatures between 323K and 77K. For the steel with annealed microstructure, the ductile-to-brittle transition appearance temperature (DBTT) was lower than the Charpy transition temperature (CTT). With increasing annealing time at 873K, the DBTT and the CTT increased, and the DBTT approached the CTT. The DBTT decreased with decreasing effective grain size. The effective grain size correlated to the grain size of the larger grain size peak in the distribution of grains with {100} planes. The annealed microstructures had higher yield strength for equivalent toughness (including upper shelf energy, DBTT and CTT) compared to th...

British Library Electronic Table of Contents (United Kingdom)

The effect of sodium gluconate anion (SG) on the corrosion and scale inhibition of ordinary steel in simulated cooling water has been studied using weight loss, polarisation curves, electrochemical impedance spectroscopy (EIS) and scanning electron microscopy (SEM) techniques. SG was studied in concentration from 10-4M to 10-1M. Results obtained reveal that SG perform excellently as corrosion and scaling inhibitor for ordinary steel in simulated cooling water. An increase of SG concentration leads to the increase of the corrosion potential towards the positive direction. The inhibition efficiency was a low temperature dependence. The inhibitor mechanism was treated as an adsorption process according to Langmuir adsorption isotherm. The SEM/EDAX data show that was a corrosion and scale inhi...

Science.gov (United States)

A separation phenomenon occurring during the Charpy impact test of API X80 pipeline steels was investigated in the present study. A detailed microstructural analysis of fractured impact specimens showed that the band structure of bainite elongated along the rolling direction worked as prior initiation sites for separations, and that the number and length of the separations increased with the increasing volume fraction of bainite. In the steels having high work hardenability, tearing-shaped separations were found because the hammer-impacted region was seriously hardened during the impact test, which led to the reduction in the impact toughness. As the test temperature decreased, the tendency toward separations increased, but separations were not found when the cleavage fracture prevailed at very low temperatures. These findings suggested that the formation of bainite and secondary phases should be minimized for preventing or minimizing ...

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on stainless steels in a borate buffer solution (pH 9.2) have been investigated by capacitance measurements and photoelectrochemistry. The study was carried out on films formed on AISI type 304 and 316 stainless steels and high purity alloys with differing chromium, nickel, and molybdenum contents. Complementary research by Auger analysis shows that the passive films are composed essentially of an inner chromium region in contact with the metallic substrate and an outer iron oxide region developed at the film/electrolyte interface. The semiconducting properties of the passive films are determined by those of the constituent chromium and iron oxides which are of p-type and n-type, respectively. Thus the influence of the alloying elements on the semiconducting properties of the passive films is explained by changes in the electronic structure of each of these two oxide regions.