In relation to coal liquefaction reaction, the effect of the coexistence of transferablehydrogen (TH) from process solvent on reduction of radical concentration and the effect of pre-heat treatment on average structure of coals were studied. In experiment, change in radical concentration with temperature rise was measured using the system composed of Yallourn coal and process solvent. The results are as follows. Process solvent with a wide boiling point range of 180-420{degree}C is effective in suppressing an increase in radical concentration even at higher temperature. The effect of hydrogen-donating solvent increases with TH. It was also suggested that high-boiling point constituents in solvent stabilize radicals even over 400{degree}C by vapor phase hydrogenation. The experimental results of pre-heat treatment are as ...
Using hydrogen at high pressures of up to 150 bar as an OH scavenger in aqueous MV"2"+ solutions (pH 1) it is possible to differentiate between two kinds of transient formed simultaneously by H-atom attack on methyl viologen. One of them is assigned to an H adduct on the N atom, MV"+H"+, with absorption bands identical to those of the radical cation, MV"+. The MV"+H"+ species deprotonates forming the long-lived radical cation, MV"+. The second type of transient produced is attributed to an H-adduct on the ring carbon, MV"2"+H, decaying by second-order kinetics. The formation of MV"+ by electron transfer from the propan-2-ol radical has been reinvestigated (pH 0 to 7); its absorption spectrum does not change in this pH range. Rate constants and molar extinction coefficients are presented. (U.K.).
Pretreatment of brown coal in oil was conducted using 1-methyl naphthalene or mixture of tetralin and 1-methyl naphthalene as solvent at temperatures ranging from 300 to 430{degree}C under nitrogen atmosphere. Effects of the solvent properties on the structural change of oxygen-functional groups (OFG) and coal liquefaction were investigated by means of quantitative analysis of OFG and solid state {sup 13}C-NMR measurement. When hydrogentransfer from solvent was insufficient, it was suggested that brown coal molecules loose their hydrogen to be aromatized. While, at lower temperatures ranging from 300 to 350{degree}C, hydrogen contained in brown coal molecules was consumed for the stabilization of pyrolytic radicals, and the deterioration of liquefaction was not observed. When hydrogentransfer from solvent was insufficient at higher ...
For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogentransfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic ...
It was previously reported that the tritium tracer method is useful for the quantitative consideration of hydrogen behavior in coal during coal liquefaction reaction. Tetralin is excellent hydrogen donating solvent, and is considered as one of the model compounds of coal. In this study, effects of H2S and H2O on the hydrogen exchange reaction between tetralin and gaseous hydrogen labeled by tritium were investigated. It was suggested that the conversion of tetralin and the hydrogen exchange reaction between gaseous hydrogen and tetralin proceed through the radical reaction mechanism with a tetralyl radical as an intermediate product. When H2S existed in this reaction, the hydrogen exchange yield increased drastically without changing the conversion yield. This suggested that the ...
... Three prototype reactors were constructed and the photocatalysts used were TiO2 for hydroxyl radical generation, dyes such as methylene blue and rose bengal for singlet oxygen generation, and ferric chloride/hydrogen peroxide in Photo-Fenton OH radical generation. Singlet oxygen was effective against some of the pesticides but reacted slowly or not at all with others. All pesticides were degraded by OH radical generating agents (such as methylene blue)...
Pulsed radiolysis method is used to study transformations intermediates of 6-aminophenalenone in ethanol. In alkaline medium the main product is radical-anion of 6-aminophenalenone, which optical absorption spectrum contains two bands with maxima at 355 and 400 nm. The particle precursors are e_s, CH_3CHOH and CH_3CHO"- radicals. In neutral and acid medium radical-anions are protonated in reactions with alcohol and hydrogen ions. The resulting H-adduct of 6-aminophenalenone has optical absorption maxima at 350 and 390 nm. Availability of two maxima is related to two various product structures. Molar extinction coefficients of radical-anions and H-adducts of 6-aminophenalenone and rate constants of reactions with their participation are estimated.
Intermediate products of the conversions of 6-aminophenalenone in ethanol were investigated by pulse radiolysis. In alkaline medium the main product is the 6-aminophenalenone radical cation, the optical absorption spectrum of which contains two bands with maxima at 355 and 400 nm. The precursors of this particle are e_s, CH_3CHOH and CH_3CHO"- radicals. In neutral and acid medium, radical cations are protonated in reactions with alcohol and hydrogen ions. The H-adduct of 6-aminophenalenone that arises has optical absorption maxima at 350 and 390 nm. The presence of two maxima is due to two different structures of the product. The molar extinction coefficients of the radical anions and H-adducts of 6-aminophenalenone and the rate constants of the reactions involving them were estimated. 6 refs., 4 figs., 2 tabs.
There are several methods of generating OH free radicals from ozone and/or hydrogen peroxide and ultraviolet light. They all have in common that the OH free radicals originate in one single source only whereas in the combination of ozone with ionizing radiation two simultaneous working sources for the OH free radicals exist. The resulting higher OH free radical concentration makes this process especially apt for the remediation of low level contaminated groundwater as for example trichloroethylene (TCE) contamination in the sub-ppm range. A cost comparison between O_3/UV and O_3/electron beam for remediation of a groundwater contaminated with 100 ppb TCE indicated that for a throughput of about 5 million gallons/day the O_3/electron beam process is more cost-effective. (authors).
Hyperquenching of liquid water with cooling rates of 10{sup 6}-10{sup 7} K s{sup -1} yields glassy water. Upon {gamma}-irradiation at 77 K, the only paramagnetic species accumulating in hyperquenched glassy water are the hydroxyl and hydroperoxyl radicals. There are no hydrogen atoms or electrons seen by the ESR technique. For irradiation doses up to about 70 kGy, the relative contributions of hydroxyl and hydroperoxyl radicals to the total amount of paramagnetic species remain virtually constant. The total amount of paramagnetic species, n, is sublinear in dose, d, well approximated by n=8.55x10{sup 16}d{sup 0.8} for n in spin g{sup -1} and d in kGy.
The work presented here demonstrates the ability of proton-transfer-reaction mass spectrometry (PTR-MS) to perform fast-response measurements of volatile organic compounds (VOCs) (including methanol, acetonitrile, acetaldehyde, acetone, PAN-type compounds, alpha- and beta-pinene, nopinone and pinonaldehyde) at the pptv level and its versatile applicability in the field of environmental trace gas analysis. Laboratory and field experiments including various calibration techniques and intercomparisons with other measurement techniques such as gas chromatography, atmospheric pressure chemical ionization and Fourier transformation infrared spectroscopy were performed providing a first characterization of the PTR-MS instrument performance (sensitivity, detection limit, precision, accuracy). Typically a detection limit (S/N=2) of 50 pptv for a 10 s signal integration time, a precision of 5 % and an accuracy in the range between 10 and 25 % were observed. Due to its ...
Recent work has shown that natural hydrocarbon emissions can significantly affect the levels of urban and regional tropospheric ozone. We report on the reactivities of these biogenic trace gases, particularly isoprene, focusing on their importance in the production of aldehydes and peroxy radicals, leading to increased levels of hydrogen over regional forests. Hydrogen peroxide can lead to the wet oxidation of sulfur dioxide to acidic sulfate in aerosols, fogs, and clouds. In turn, acidic sulfate can act to as a light scattering aerosol and a source of cloud condensation nuclei (CCN), potentially leading to global cooling. Aerosol sulfate and other dissolved organic and inorganic compounds can also play important roles as a greenhouse species in the lower troposphere.
In this paper, bond cleavage reactions are discussed in relation to the softening and solubilization of coal. Were used 9,10-dihydroanthracene (DHA) and 9,10-dihydrophenanthrene (DHP) as models of hydrogen donating compounds in coal, and bibenzyl, 1,2-diethane, benzylphenylether, and 1,5-dibenzylnaphthalene were used as models of bridge structure compounds. They were compared mutually, as to reactivity of coal against DHA and DHP. For the homolytic cleavage of bridges, DHA with excellent radical supplement performance provided excellent hydrogen donating performance. While, for the ipso-position cleavage of bridges, it was found that DHP can act as an effective hydrogen donor. For the reaction between coal and hydrogenated aromatic compounds, cleavage of relatively weak bonds, such as ether linkage and dimethylene linkage, occurred at about 380{degree}C, and ...
Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are though to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.
Some applications of magnetic resonance in coal liquefaction research described briefly are: (1) investigation of the nature of carbon deposits on used coal-liquefaction catalysts, (2) determination of the fate of hydrogen during coal liquefaction, and (3) observation of transient free radicals during coal pyrolysis. The first two applications make use of cross-polarization /sup 13/C magnetic resonance combined with magic angle spinning, and the third application is an electron spin resonance study. (BLM)
One-electron oxidation of several derivatives of pyrazolin-5-one, including the drug antipyrine, were studied by pulse radiolysis of aqueous solutions. All the compounds were found to be oxidized by Br2 rapidly but considerably more slowly by weaker oxidants, such as peroxyl radicals. From redox equilibria using p-methoxyphenol and N,N,N',N'-tetramethyl-p-phenylenediamine as reference compounds, the one-electron oxidation potentials of the methyl-substituted 2-pyrazolin-5-ones were found to be in the range of 0.32-0.39 V versus normal hydrogen electrode. The relevance of these findings to the properties of the drug nafazatrom is discussed. Antipyrine was found to have a much higher oxidation potential, estimated as 1.2-1.5 V, which is rationalized on the basis of the phenyl substitution and lack of resonance stabilization of the radical cation.
Abstract Green tea extract showed false-negative results in the determination of glucose via glucose oxidase (GOD) test. This investigation was undertaken to verify and find out the precise mechanism underlying this interference by determining the reaction kinetics of production and reduction of end-point chromophore. The peroxidase step of the GOD test was found to be interfered and phenols of the green tea were the interfering compounds. Green tea interfered and exerted its influence in a dual fashion. A part of the interference was observed as a result of the reduction of the finally formed chromophore, whereas the other form of interference was due to its hydrogen peroxide/free radical-scavenging activity. Reducing potential and the free radical-scavenging activity of the phenols in th...
Oxidative degradation of methylene blue (MB) by Co^2^+-HCO3^- system with H2O2 in aqueous solution was studied. Nearly complete decolorization of the dye was obtained in less than 50min in diluted NaHCO3 solution (25mM) in the presence of only 20mM Co^2^+ ions. Meanwhile, the conjugated structure and phenyl rings of the MB molecule were destroyed or even broken down into small organic acids and inorganic ions, as indicated by FT-IR spectra and ion-chromatography. Photoluminescence probing and radical scavenging technologies suggested that the reaction of MB degradation in this system mainly involved the generation and participation of hydroxyl radicals. Furthermore, by cyclovoltammetric measurements, the in situ formed different complexes between Co^2^+ and HCO3^- were observed at differen...
The reactions of the hydroxyl radical with hydrocarbons and fluoro hydrocarbons attract significant attention due to their importance in atmospheric chemistry. Its reactions with the two first hydrocarbons, methane and ethane are of special interest because, owing to the small size of these systems, they serve as a prototype for the theoretical studies of hydrogen abstraction reactions. In this work, the reaction and activation energies of the hydroxyl radical abstraction reaction with methane and ethane have been investigated by correlated ab initio and DFT methods. The DFT reaction energies are in good agreement with experimental values, but the activation energies may be in severe error. (authors) 22 refs.
Hydroperoxides are important atmospheric oxidants. They are responsible for most of the oxidation of aqueous-phase SO(sub 2) to sulfate in the northeastern United States, resulting in the formation of acid precipitation and visibility-reducing sulfate aerosol (Penkett et al., 1979; Lind et al., 1987; Madronich and Calvert, 1990; Tanner and Schorran, 1995). Atmospheric hydrogen peroxide (H(sub 2)O(sub 2) or HP) is produced by the self-reaction of hydroperoxyl radicals (HO(sub 2)); higher organic peroxides are produced by reaction of HO(sub 2) with alkylperoxyl radicals (RO(sub 2)). Peroxyl radicals, along with OH, are chain carriers in the complex photochemical process that produces tropospheric ozone. Thus, concentrations of peroxides and their free radical precursors depend on solar intensity and ambient concentrations of water vapor, ozone, NO(sub x) (NO+ NO(sub 2)), and VOCs ...
In the presence of hydroxyl anion, both formaldehyde and glyoxal are known to undergo rearrangements involving intermolecular and intramolecular hydride transfer (the Cannizzaro and Benzilic acid rearrangements respectively). The authors report ab initio SCF-MO calculations of the transition state geometries, the activation barriers, and the hydrogen isotope effects for these two reactions. The structure of the transition state for the rection involving formaldehyde is usually basis set dependent, becoming more linear and symmetrical as the basis set size increases. In contrast, the analogous transition state for the glyoxal reaction involves a highly non-linear hydride transfer. They find the isotope effects to be quite low for the Cannizzaro reaction, and significantly larger for the non-linear benzilic acid rection, in apparent contradiction to Westheimer's suggestion the isotope effects reach a maximum for linear ...
It is well established from experiments in premixed, laminar flames, jet-stirred reactors, flow reactors, and batch reactors that SO2 acts to catalyze hydrogen atom removal at stoichiometric and reducing conditions. However, the commonly accepted mechanism for radical removal, SO2 + H(+M) reversible arrow HOSO(+M), HOSO + H/OH reversible arrow SO2 + H-2/H2O, has been challenged by recent theoretical and experimental results. Based on ab initio calculations for key reactions, we update the kinetic model for this chemistry and re-examine the mechanism of fuel/SO2 interactions. We find that the interaction of SO, with the radical pool is more complex than previously assumed, involving HOSO and SO, as well as, at high temperatures also HSO, SH, and S. The revised mechanism with a high rate constant for H + SO2 recombination and with SO + H2O, rather than SO2 + H-2, as major products of the HOSO + H reaction is in agreement with ...
Five arylethylenes with 1-naphthyl, 2-naphthyl, and phenyl groups in 1,2-positions have been studied for singlet-mediated charge-transfer interactions with several amines and paraquat dication. 1-Phenyl-2-(2-naphthyl)ethylene and 1,2-di(2-naphthyl)ethylene exhibit distinct dependence of exciplex emission maxima and lifetimes, and fluorescence quenching constants, on excitation and/or monitoring wavelengths; this is in conformity with the existence of ground-state rotamers for these systems, wtih distinguishable absorption-emission spectra and fluorescence lifetimes. The fluorescence quenching by aromatic amines and paraquat dication occurs with rate constants in the limit of diffusion control and is accompanied by the formation of radical ions in polar solvents (acetonitrile). The transient spectra and kinetics associated with the radical ions, observed by 337.1- and 355-nm laser flash photolysis, are also reported. 10 ...
This invention is a manufacturing method of a metal-hydrogen alkali battery cell consisting of a positive electrode of metal oxides, alkaline electrolyte solution and a separator containing an amide-radical, wherein the above treating solution is aqueous solution of KOH (or NaOH) which is heated at least at 40 centigrade and the separator is first immersiion-treated and then water-washed and dried. The amide-radical-containing separaator uses a nylon non-woven fabrics. Average molecular weight of nylon 66 is 12,000 - 20,000. In this invention, in order to improve the storage ability and the cycle characteristics which are caused by corrosion of a separator which takes place in the cell after its assembly, the separator is immersed in a hot alkali in order to obtain a non-woven fabric of nylon 66 consisting of alkali-stable high molecular weight portion, which is assembled into a battery. By this, the dissolving of the ...
Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogentransfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of ...
The aim of this work was to study the energy transfer mechanisms from the ligand to the central lanthanide ion of tetracycline-europium (Tc-Eu) complex. The absorption spectra of a EuCl{sub 3}.H{sub 2}O solution was measured and absorption cross-section of Eu{sup 3+} was estimated. The observed overlap predicts a resonant energy transfer from Tetracycline to Eu{sup 3+}. The microscopic parameter of energy transfer was obtained using the overlap integral calculation considering a dipole-dipole energy transfer mechanism and results were compared considering an energy transfer by exchange. In this work, we report also the optical properties of Tc-Eu complex when urea hydrogen peroxide is added to the aqueous solution.
A new potential function based on spectroscopic results for diatomic molecules is presented and applied to the hydrogen bonding systems. The potential energy of interaction is supposed to have electrostatic, polarization, dispersion, repulsion and effective charge-transfer contributions. Estimates of the effective charge-transfer quantity have been made based on the average charge of the proton donor and the acceptor atoms. For dimers such as water, methanol, acetic acid and formic acid, the vibrational stretching frequencies and dimerization energies are calculated and discussed in connection with Badger-Bauer rule. (author).
PWR primary circuit radiolysis model describes oxygen/hydrogen behavior in the Westinghouse Sizewell B 4-loop PWR (SNUPPS design). The effect of oxygen ingress have also been evaluated using the same model. There is clear agreement from experimental and modelling data that the dissolved hydrogen concentration required to suppress radiolysis decreases as the temperature increases. There is good evidence from the study at the Belleville PWR that {approx}5 cc(STP)kg{sup -1} H{sub 2} is sufficient to suppress radiolysis during power operation. Modelling indicates that the minimum hydrogen concentration is about 0.5 cc (STP)kg{sup -1} at PWR operating temperatures and that the presence of boric acid has little effect on this value, although it does increase the steady-state concentration of H{sub 2}O{sub 2}. Downstream of the core the concentrations of both oxygen and hydrogen peroxide fall by about two ...
Singlet oxygen generators are multiphase flow chemical reactors used to generate energetic oxygen to be used as a fuel for chemical oxygen iodine lasers. In this paper, a theoretical model of the generator is presented along with its solutions over ranges of parameter space and oxygen maximizing optimizations. The singlet oxygen generator (SOG) is a low-pressure, multiphase flow chemical reactor that is used to produce molecular oxygen in an electronically excited state, i.e. singlet delta oxygen. The primary product of the reactor, the energetic oxygen, is used in a stage immediately succeeding the SOG to dissociate and energize iodine. The gas mixture including the iodine is accelerated to a supersonic speed and lased. Thus the SOG is the fuel generator for the chemical oxygen iodine laser (COIL). The COIL has important application for both military purposes--it was developed by the US Air Force in the 1970s--and, as the infrared beam is readily absorbed by metals, industrial cutting ...
The set of activities performed by SENTECH, Inc. addressed the specific recommendations provided to the Department of Energy (DOE) by its advisors, including the Hydrogen Technical Advisory Panel and the review panel members of the DOE Annual Hydrogen Program Review. SENTECH`s efforts were conducted under five tasks: Task 1: Technology and Process Analysis; Task 2: Hydrogen Information Development and Transfer; Task 3: Educational Products; Task 4: Systems Analysis; and Task 5: Life Cycle Costs. SENTECH activities were executed in two broad areas--analysis and technology transfer. The analytical tasks undertaken in FY97 were focused on two types of analysis--systems analysis and technical/economic assessments. These analytical activities benefit DOE by providing data that allow it to define the strategic goals of the hydrogen R and D program. By collecting ...
With an objective to know coal condensation structure which has influence on coal conversion reaction, an attempt was made on quantitative evaluation of hydrogen bonding in coal. Using as test samples the VDC made from Taiheiyo coal swollen by tetralin and vacuum-dried, and its pyrolyzed char, DSC measurement and Fourier transform infrared spectroscopy (FT) were performed. An FT spectrum comparison revealed that the VDC swollen at 220{degree}C has the hydrogen bonding relaxed partly from the original coal. However, since the change is in a huge coal molecular structure restraining space, it has stopped at relaxation of the bonding energy without causing separation as far as free radicals. On the other hand, the DSC curve shows that the VDC has slower endothermic velocity than the original coal. In other words, the difference in heat absorption amounts in both materials is equivalent to the difference of enthalpy ({Delta} H) ...
The nature of radicals in wood irradiated in vacuum was studied by ESR method. The decay rate of radicals changes in three temperature ranges. Long-lived radicals are very stable at 298"0K, at which the wood-plastics composite has often been studied. The number of radicals formed by irradiations shows fairly good agreement with the total number of radicals in each isolated wood component. The graft copolymerization of MMA to irradiated wood was also studied by means of ESR, and it was found that PMMA propagating radicals are formed in irradiated wood. These radicals are probably formed by the result of graft copolymerization of MMA of wood. (auth.).
Means of intensifying heat transfer with nucleate boiling, based on boiling under constrained conditions (in slots, on a capillary-porous surface) are the most promising since a high intensity of heat transfer is ensured. In the present work we attempt to evolve the main assumptions for the physical model of the process of vapour formation under constrained conditions and to extend them to the boiling of cryogenic liquids on surfaces with a capillary-porous deposit; also, the results are given of experimental investigations of heat transfer with the boiling of nitrogen, oxygen and hydrogen at atmospheric perssures and below on capillary-porous surfaces of various metals of different structure produced by an electric arc method of gasothermal spray coating.
The NiMo sulfide supported on Ketjen Black (KB) was more effective and yielded lighter oil products containing light fractions with their boiling point below 300{degree}C during the two stage liquefaction combining low temperature and high temperature hydrogenation the conventional NiMo/alumina catalyst and FeS2 catalyst. Although the NiMo/alumina yielded increased oil products during the two stage liquefaction, the lighter oil fractions did not increase and the heavier fractions increased mainly. This suggests that the hydrogenation of aromatic rings and successive cleavage of the rings are necessary for producing the light oil, which is derived from the sufficient hydrogenation of aromatic rings using catalysts. For the two stage reaction with NiMo/KB catalyst, it was considered that sufficient hydrogen was directly transferred to coal molecules at the first stage of the low ...
A conceptual fusion synfuel production system has been developed with the unique features of: (1) a fusion blanket producing high-temperature (1250"0C) process heat, and (2) the GA sulfur-iodine thermochemical cycle. The system incorporates a two-zone blanket which achieves a tritium breeding ratio of 1.1 while delivering a high fraction (30%) of the fusion heat at high temperatures (1250"0C). The multiple barriers to tritium permeation in the blanket design permit the hydrogen product to meet 10CFR20 regulatory requirements without stringent requirements on the tritium recovery systems. A ceramic heat exchanger, incorporating SiC tubes and headers to contain the process stream and a cooled, Inconel 718 pressure shell to contain the helium, was designed for transferring the heat from the high-temperature coolant to the process. A good heat-line match of the blanket heatsource temperature distribution to the requirements of the thermochemical ...
In order for fuel cells to be successful, a full-scale hydrogen infastructure is required. The HyTra concept is presented here (HYdrogen TRAnsform, Transfer and TRAnsport) involves combined production, storage and supply of hydrogen in a transportable trailer, i.e. it is both a hydrogen production unit and a mobile filling station. The trailer can be transported to the selected site, where it will produce gaseous hydrogen from electricity and water by electrolysis. A compressor pumps the gas into an internal pressure tank and compresses it to filling pressure. Filling takes place by the overflow principle via a flexible high-pressure line with a standardised H{sub 2} filling unit. (orig.) [German] Um die Marktdurchdringung der Brennstoffzellentechnik gewaehrleisten zu koennen, muss eine flaechendeckende Wasserstoffinfrastruktur aufgebaut werden. Das neue ...
The vacuum polarization splitting of the M-shell states in muonic hydrogen can have a profound influence on the muonit de-excitation cascade in deuterium and tritium targets. The cascade also shows sensitive dependence on the precise rate of transfer processes between certain excited muonic deuterium and tritium atoms. Recent experimental data, where a much greater population of the (d..mu..) qs state (1/sub 1//sub //sub s/) was found than previously predicted, can be explained if the transfer rates from the (d..mu..) M-shell are assumed to be strongly suppressed.
New market based approaches are becoming increasingly important as instruments of environmental policy. The two main market approaches, i.e., transferable pollution permits (experimented in America), and 'green' energy surcharges (European philosophy), are described and discussed. An analysis of information on their state of implementation shows that, in the case of the former method, the greatest sources of difficulty arise in the determination of acceptable ceiling levels of emissions, in the distribution of permits among the various polluting firms, and in the legality of granting rights to pollute. Instead, the European experience has evidenced that energy surcharges motivated by environmental policy cannot have an appreciable positive impact on consumers or the economic system in general unless they are accompanied by well defined measures geared towards the promotion or creation of alternative solutions such as to stimulate ...
The primary charge separation in photosynthetic bacteria generates a dimeric bacteriochlorophyll (BChl) cation and a bacteriopheophytin (BPheo) anion which lie within close proximity of each other (approx. 10 A). The two radicals also lie within van der Waals contact on opposite sides of a lone BChl bridging molecule. Spectral changes in the red (Q/sub y/) band of the bridge BChls have been observed on picosecond time scales following excitation of the reaction center (RC) and have been variously attributed to the formation of a BChl anion, to a charge-transfer state, or to electrochromic effects. They present calculations here which suggest that electrochromic effects caused by the photogenerated cation and/or anion can rationalize the optical changes observed in the flash photolyses as well as in trapping experiments.
Two electroactive polymeric arylene bisimides, namely poly[(4,7,10-trioxatrideca-1,13-diyl)-(1,4,5,8-naphthalenetetracarboxylic bisimide-N,N'-diyl)] and its perylene analogue - poly[(4,7,10-trioxatrideca-1,13-diyl)-(3,4,9,10-perylenetetracarboxylic bisimide-N,N'-diyl)] have been synthesized and studied by cyclic voltammetry, UV-vis-NIR as well as Raman spectroeletrochemistry. Contrary to low molecular weight arylene bisimides, which show a clear two electron, double-step electrochemical reduction (neutral form to radical anion and from radical anion to dianion), in the synthesized polymers multielectron transfers are observed, accompanied with a strong electrochromic effect. However, as probed by cyclic voltammetry, their first reduction step is retarded and covers a wider potential range. We attribute this effect to macromolecular nature of the compounds being reduced and their structural inhomogeneity caused by ?-stacking ...
The wavefunction of a particle extends into the classically forbidden barrier region of the potential energy surface. The consequence of this partial delocalisation is the phenomenon of quantum tunnelling, an effect which enables a particle to penetrate a potential barrier of magnitude greater than the energy of the particle. The tunnelling probability is an exponential function of the particle mass. The effect is therefore an important contribution to the behaviour of light atoms, in particular the proton. The hydrogen bond has long been appreciated to be an essential component of many biological and chemical systems, and the proton transfer reaction in the hydrogen bond is fundamental to many of these processes. The proton behaviour in the hydrogen bonds of benzoic acid, acetylacetone and calix-4-arene has been studied. A variety of techniques, both experimental and computational, were adopted for the ...
This report seeks to address the role of hydrogen bonding with Bronsted acids and bases in proton-coupled electron transfer (PCET) as it pertains to concerted or stepwise pathways of quinone (Q) and hydroquinone (QH_2) electrochemistry. This study was performed using a series of techniques that included cyclic voltammetry (CV), digital simulations, computational chemistry and "1H NMR. Hydrogen bonding was inferred by a decrease in diffusion coefficient (D) values measured using a pulsed gradient echo- (PGE-) "1H NMR technique. Changes of 40.8% and 37.9% in D values were only noted after the addition of two equivalents of acetate to 1,4-hydroquinone (1,4-QH_2) and catechol (1,2-QH_2), respectively. In contrast, the D values for the addition of selected amines (pyridine, N,N-diisopropylethylamine and triethylamine) changed only 3.2% on average. Quantum mechanical calculations were conducted to determine the pK_a of all ...
A vast amount of circumstantial evidence implicates oxygen-derived free radicals (especially, superoxide and hydroxyl radical) and high-energy oxidants [such as peroxynitrite (OONO−)]...Full Text Available
The tribo characteristics of self-lubricating 40-mm-bore ball bearings with a retainer of glass cloth-polytetrafluoroethylene (PTFE) laminate, which has elliptical pockets with a large pocket clearance, were tested under thrust loads at speeds up to 50,000 rpm, 2 million DN, in liquid hydrogen (LH2) and in liquid nitrogen (LN2). During testing, the bearing torque, outer-race temperature, and electric resistance between the inner and outer races were monitored to verify the formation and rupture of a PTFE transfer film. Testing showed that the bearings having the elliptical retainer pockets were superior to the conventional bearings with circular pockets. It was determined that, at the maximum inner race spinning velocity of about 5 m/s, a PTFE transfer film could sustain the maximum Hertz stress, up to about 2000 N/sq mm, in LH2, without severe film rupture resulting in bearing seizure. In LN2, the critical load capacity of ...
Comparisons have been made between Buddhism and the philosophy of science in general, but there have been only a few attempts to draw comparisons directly with the philosophy of radical behaviorism....Full Text Available
The authors present some recent measurements on electroweak physics using data collected by the CDF experiment at the Tevatron proton anti-proton collider ({radical}s = 1.96 TeV) at Fermilab.
The theoretical analysis of a partially-ionized hydrogen gas flow (gas temperatures of approximately 10,000 to 20,000 K) through a particular class of magnetohydrodynamic (MHD) generators and the preliminary design of these MHD generators as open cycle, electric power supplies are performed. Analysis of the gas flow through these ultra-high temperature MHD generators requires a coupled gas dynamics/radiative heat transfer solution. Gas dynamics are modeled by a set of quasi-one-dimensional, nonlinear differential equations which account for friction, convective and radiative heat transfer and the interaction between the ionized gas and applied magnetic field. Radiative heat transfer is modeled using non-gray, absorbing-emitting two- and three-dimensional P-1 approximations which permit an arbitrary variation of the spectral absorption coefficient with frequency. Gas dynamics and radiative heat ...
Direct electrochemistry and electrocatalysis of catalase (Cat) was studied based on a nano-composite film consisting of amine functionalized graphene and gold nanoparticles (AuNPs) modified glassy carbon electrode. Graphene was synthesized chemically by Hummers and Offeman method and then was functionalized with amino groups via chemical modification of carboxyl groups introduced on the graphene surface. The nano-composite film showed an obvious promotion of the direct electron transfer between Cat and the underlying electrode, which attributed to the synergistic effect of graphene-NH2 and AuNPs. The resultant bioelectrode retained its biocatalytic activity and offered fast and sensitive H2O2 quantification. Under the optimized experimental conditions, hydrogen peroxide was detected in the...
Examination is made of the main features of the physical and chemical preignition processes within homogeneous mixtures of air and gaseous fuels, such as propane, methane and hydrogen in a motored engine, while employing detailed chemical kinetics in a one zone analytical model. The changes in the compression temperature and pressure due to the admission of gaseous fuels, energy release during the preingition reactions and the contributions of heat transfer and residual gases to the preignition reaction activity were followed over a number of consecutive cycles until the occurrence of autoignition. Some of the observed differences in engine behaviour when operating on methane, propane and hydrogen were discussed with particular reference to the observed trends in dual fuel engine operation. Calculated results showed good agreement with some corresponding experimental trends. 14 refs., 9 figs.
An electrochemical biosensor for determination of hydrogen peroxide (H2O2) was fabricated, based on the electrostatic immobilization of horseradish peroxidase (HRP) with one-dimensional gold nanowires (Au NWs) and TiO2 nanoparticles (nano-TiO2) on a gold electrode. The nano-TiO2 can give a biocompatible microenvironment and compact film, and the Au NWs can provide fast electron transferring rate and greatly add the amount of HRP molecules immobilized on the electrode surface. Au NWs were characterized by ultraviolet?visible spectra and transmission electron microscope. The electrode modification process was probed by cyclic voltammetry and electrochemical impedance spectroscopy. Chronoamperometry was used to study the electrochemical performance of the resulting biosensor. Under optimal co...
A method for the quantitative determination of atmospheric hydroperoxyl radical comprising: (a) contacting a liquid phase atmospheric sample with a chemiluminescent compound which luminesces on contact with hydroperoxyl radical; (b) determining luminescence intensity from the liquid phase atmospheric sample; and (c) comparing said luminescence intensity from the liquid phase atmospheric sample to a standard luminescence intensity for hydroperoxyl radical. An apparatus for automating the method is also included.
Phospholipid vesicles were found to be lysed by exposure to free radicals derived from irradiated glycine and galactose. The decomposition yield increased with vesicle concentration, and attained values of 0.0006 vesicles destroyed per radical added. Ionic charge at the phospholipid end groups was found to be more important than degree of unsaturation in determining this yield. Radicals derived from irradiated serine and alanine had no detectable lytic action at the vesicle concentrations tested.
The activities of Shell Hydrogen in the development of a hydrogen economy are outlined. Attention is paid to the use of hydrogen in electric cars and in homes, different types of fuel cells, and the catalytic partial oxidation (CPO) process of Shell to produce hydrogen
The activities of Shell Hydrogen in the development of a hydrogen economy are outlined. Attention is paid to the use of hydrogen in electric cars and in homes, different types of fuel cells, and the catalytic partial oxidation (CPO) process of Shell to produce hydrogen.
Lawrence Livermore, Sandia Livermore and Los Alamos National Laboratories have a joint project to develop an optimized hydrogen fueled engine for series hybrid automobiles. The major divisions of responsibility are: system analysis, engine design and kinetics modeling by LLNL; performance and emission testing, and friction reduction by SNL; computational fluid mechanics and combustion modeling by LANL. This project is a component of the Department of Energy, Office of Utility Technology, National Hydrogen Program. We report here on the progress on system analysis and preliminary engine testing. We have done system studies of series hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. The impact of various on-board storage options on fuel economy are ...
Lawrence Livermore, Sandia Livermore and Los Alamos National Laboratories have a joint project to develop an optimized hydrogen fueled engine for series hybrid automobiles. The major divisions of responsibility are: system analysis, engine design and kinetics modeling by LLNL; performance and emission testing, and friction reduction by SNL; computational fluid mechanics and combustion modeling by LANL. This project is a component of the Department of Energy, Office of Utility Technology, National Hydrogen Program. We report here on the progress on system analysis and preliminary engine testing. We have done system studies of series hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. The impact of various on-board storage options on fuel economy are ...
Experimental investigation data are systematized of free radical states and processes in irradiated proteins. The investigation is performed by the radiospectral methods. Results are discussed in detail of the study of free radicals electronic structure of amino acids, peptides and proteins formed by the action of ionizing radiation. The specificity is stressed of the study of monocrystalls of these compounds by the method of electronic paramagnetic resonance. The nature is also studied of primary centres formed under the effect of radiation on biologically important compounds and their subsequent reactions in solid and liquid solutions. Ion-radical states of different functional groups of the protein molecule are studied. Prospects of the study and the role of anion-radicals in biological processes are discusses.
Spectra of e.p.r. radicals in cellulose and timber gamma-irradiated at 77 and 300 K have been measured. Radiation yields and the kinetics of radicals accumulation have been studied. The effect of ionizing radiation on cellulose is the appearance of radicals resulting from rupture of C-H bonds in positions 1 and 4. Timber, additionally, forms ''lignin'' radicals. A mechanism of cellulose and timber radiolysis is suggested. ''Lignin''-type compounds present in timber protect polysaccharides from radiation-induced destruction.
The microbial process of converting organic matter into methane and carbon dioxide is so complex that anaerobic digesters have long been treated as {open_quotes}black boxes.{close_quotes} Research into this process during the past few decades has gradually unraveled this complexity, but many questions remain. The major biochemical reactions for forming methane by methanogens are largely understood, and evolutionary studies indicate that these microbes are as different from bacteria as they are from plants and animals. In anaerobic digesters, methanogens are at the terminus of a metabolic web, in which the reactions of myriads of other microbes produce a very limited range of compounds - mainly acetate, hydrogen, and formate - on which the methanogens grow and from which they form methane. {open_quotes}Interspecies hydrogen-transfer{close_quotes} and {open_quotes}interspecies formate-transfer{close_quotes} are major ...
A detailed kinetic study of the epoxidation of 1-octene with hydrogen peroxide catalyzed by Pt(II) complexes is reported. The two systems analyzed were (diphoe)Pt(CF/sub 3/)(OH)/1-octene/H/sub 2/O/sub 2//THF and ((diphoe)Pt(CF/sub 3/)(CH/sub 2/Cl/sub 2/))BF/sub 4//1-octene/H/sub 2/O/sub 2//H/sub 2/O/CH/sub 2/Cl/sub 2/. Rate data were determined with GLC from epoxide formed vs time plots. Evidence for many of the organometallic intermediates and the individual steps involved was gained from IR studies, /sup 19/F NMR studies, and especially designed experiments including studies of the acidity effect. In both cases the kinetic analysis suggests a mechanism in which the actual oxidant is a PtOOH species that interacts with a Pt-olefin complex in the oxygen-transfer step (second-order dependence on platinum). 29 references, 12 figures, 3 tables.
There is currently considerable interest in identifying and quantifying the effects of welding procedure parameters and steel composition factors on the risk of cracking in pipeline girth welds that may be experienced during winter construction. Although low ambient temperatures, that may be experienced during winter construction, are generally assumed to increase the risk of cracking there has been little work to quantify the effects and to suggest how welding procedures should be modified for winter conditions. The present work was undertaken to calculate the effects of changes in welding parameters on the thermal cycle and the diffusion of hydrogen for a typical pipeline girth weld. A simple analytical method and the finite element method (FEM) were used. Both methods gave similar results but the simple method was very sensitive to the value of heat transfer coefficient. The results showed that the relation between the ...
This quarterly report for the period July through September 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogentransfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: the rheology of Illinois No. 6 coal in hydrogenated creosote oil; dissolution chemistry of subbituminous coal; pyrite catalysis; liquefaction of Illinois No. 6 coal in indole; characterization and activity testing of catalyst samples from Wilsonville ...
When energetic heavy ions traverse a medium, the amount of energy deposited by the ions is closely related to their effective charges. The charge-state fractions of these beams are obtained by solving rate equations for the electron loss and capture processes. By assuming local balance between electron loss and capture, the charge-state distributions, the averge equilibrium charge q, and other properties are obtained as functions of the incident beam velocity. The LET (linear energy transfer) of Ne and Ar ions with energies between 0.01 and 100 MeV/amu is calculatedted using their average equilibrium charge.
This paper explores for the first time the post-radiation-induced-graft polymerization on solid substrate using reversible addition-fragmentation transfer (RAFT) mechanism. Radiation-induced graft polymerization onto polymers is a potentially interesting technique to create easily new materials from highly resistant polymers, e.g. surface graft polymerization of acrylic acid (AA) onto poly(vinylidene difluoride) (PVDF) improves its surface properties without losing its excellent mechanical properties. As a consequence of the radical nature of the polymerization processes it is difficult to control molecular weight of grafted chains, and therefore design and standardize the properties of the final product. RAFT polymerization is a suitable method to obtain monodisperse polymers. The ability of the RAFT agents to control the polymer chain length could be an interesting approach to improve the grafted polymers obtained by ...
Using a series of polycations synthesized by atom transferradical polymerization (ATRP), we investigate the effects of the polymer charge density and hydrophobicity on salt-induced interdiffusion of polymer layers within polyelectrolyte multilayer (PEM) films. Polycations with two distinct hydrophobicities and various quaternization degrees (QPDMA and QPDEA) were derived from parent polymers of matched molecular weights poly(2-(dimethylamino)ethyl methacrylate) (PDMA) and poly(2-(diethylamino)ethyl methacrylate) (PDEA) by quaternization with either methyl or ethyl sulfate. Multilayers of these polycations with polystyrene sulfonate (PSS) were assembled in low-salt conditions, and annealed in NaCl solutions to induce layer intermixing. As revealed by neutron reflectometry (NR), polycations with lower charge density resulted in a faster decay of film structure with distance from the substrate. Interestingly, when comparing polymer mobility in ...
We have done system studies of series hydrogen hybrid automobiles that approach the PNGV design goal of 34 km/liter (80 mpg), for 384 km (240 mi) and 608 km (380 mi) ranges. Our results indicate that such a vehicle appears feasible using an optimized hydrogen engine. We have evaluated the impact of various on-board storage options on fuel economy. Experiments in an available engine at the Sandia CRF demonstrated NO{sub x} emissions of 10 to 20 ppM at an equivalence ratio of 0.4, rising to about 500 ppm at 0.5 equivalence ratio using neat hydrogen. Hybrid simulation studies indicate that exhaust NO{sub x} concentrations must be less than 180 ppM to meet the 0.2 g/mile ULEV or Federal Tier II emissions regulations. LLNL has designed and fabricated a first generation optimized hydrogen engine head for use on an existing Onan engine. This head features 15:1 compression ratio, dual ignition, water cooling, ...
The radical cations from aziridine and azetidine have been characterized by ESR spectroscopy following their generation in the solid state by #gamma# irradiation of dilute solutions of the parent compounds in the CFCl_3 matrix at 77 K. The ESR parameters of the azetidine radical cation are typical of those for nitrogen-centered amine radical cations such as Me_2NH*"+. On the other hand, the radical cation formed from aziridine has very different ESR parameters that compare closely to those for the isoelectronic C...C ring-opened form of the oxirane radical cation and the allyl radical. The radical cation formed from azetidine is therefore assigned a ring-closed structure with the unpaired electron in a 2p/sub z/ orbital on nitrogen perpendicular to the ring plane, whereas the cation from aziridine is an allylic C...C ring-opened planar ...
The radical cations from aziridine and azetidine have been characterized by ESR spectroscopy following their generation in the solid state by ..gamma.. irradiation of dilute solutions of the parent compounds in the CFCl/sub 3/ matrix at 77 K. The ESR parameters of the azetidine radical cation are typical of those for nitrogen-centered amine radical cations such as Me/sub 2/NH*/sup +/. On the other hand, the radical cation formed from aziridine has very different ESR parameters that compare closely to those for the isoelectronic C...C ring-opened form of the oxirane radical cation and the allyl radical. The radical cation formed from azetidine is therefore assigned a ring-closed structure with the unpaired electron in a 2p/sub z/ orbital on nitrogen perpendicular to the ring plane, whereas the cation from aziridine is an allylic C...C ...
Objective. Cervical cancer patients who had an abandoned radical hysterectomy were evaluated for preoperative clinical predictors, complication rates, and outcomes. Study...Full Text Available
The OH-initiated photo-oxidation of n-butane was used as a source of 1- and 2-butoxy radicals. Reactions producing ketones and other organic compounds are explained. Rates of photolysis were determined and are discussed.
PurposeThe objective of this study is to evaluate the continence rate following reconstruction of the posterior urethral plate in robot-assisted laparoscopic radical prostatectomy...Full Text Available
Free radical formation has been implicated in the toxicity of a wide range of xenobiotics. In recent years, particular interest has been paid to compounds which can undergo a one electron reduction...Full Text Available
BackgroundTrichloroethylene (TCE) may induce oxidative stress which generates free radicals and alters antioxidants or oxygen-free radical scavenging enzymes.MethodsTwenty...Full Text Available
Introduction:Although radical prostatectomy (RP) is an effective treatment for prostate cancer, it has potentially deleterious effects on health-related quality of life (HRQoL)....Full Text Available
Despite being free of charge, treatment adherence to 7-day primaquine for the radical cure of Plasmodium vivax was estimated at 62.2% among patients along the Iquitos-Nauta road in...Full Text Available
We have undertaken a program which measures the photoelectron spectra of negative-ion beams. This experiment has afforded us direct information about these ions and the corresponding neutral radicals. Several ions and numerous radicals are believed to be crucial intermediates in combustion processes and flame chemistry. We have fabricated a spectrometer which directly measures electron affinities (EA). Knowledge of the EA and gas-phase acidity of a radical has enabled us to deduce several radical heats of formation and bond strengths.
Radicals formed in gamma-irradiated crystals of galactose and glycine were found, upon dissolution, to cause mutagenesis of Salmonella typhimurium strains TA-98 and TA-100. Although the reproducibility of the results has not been adequately determined, they suggest the possibility of developing a test to measure the mutagenic-carcinogenic potential of radiation-induced free radicals with a microbial system.
In order to overcome the inherent disadvantages of Ti-V-based hydrogen storage alloys, such as poor activation behavior and low high-rate dischargeability, the novel composites Ti{sub 0.17}Zr{sub 0.08}V{sub 0.35}Cr{sub 0.1}Ni{sub 0.3}-x wt.% La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} (x = 0, 5, 10 and 20) were successfully synthesized by ball milling method in the present study. And the structure and overall electrochemical properties of as-prepared composites are investigated systemically. The electrochemical studies show that the maximum discharge capacity of the composite electrodes displays no variation with the increase of La{sub 0.7}Mg{sub 0.3}Ni{sub 2.75}Co{sub 0.75} content, whereas the high-rate dischargeability (HRD) and the activation behavior are distinctly improved with increasing x. The electrochemical hydrogen kinetics of composite electrodes is also studied by means of electrochemical impedance spectroscopy (EIS), linear ...
A new diffuser/permeator design has been proposed for a new Savannah River Site tritium project. The use of a single heater well in the center of the shell had raised concerns that the Pd/Ag coils may be shielding radiative heat transfer to the walls thus reducing Pd/Ag tube temperatures near the shell below the recommended minimum operating temperature. The diffuser was fitted with thermocouples to measure shell temperatures during testing. Tests were run with the shell evacuated, helium feed flows of 0, 1000, and 2000 sccm; bleed pressures ranging from 0 to 203 kPa, and heater temperatures of 650, 675, and 700 degrees C. Hydrogen permeation tests were run with two hydrogen/helium mixtures and feed rates to simulate 1st and 2nd stage diffuser operations. Approximately 20 hours were required to bring the diffuser from ambient temperature to steady-state conditions. For tests with a heater temperature of 675 degrees C and no ...
The design considerations and computational fluid dynamics (CFD) modeling of a high efficiency, low emissions, hydrogen-fueled engine for use as the prime mover of a series hybrid automobile is described. The series hybrid automobile uses the engine to generate electrical energy via a lightweight generator, the electrical energy is stored in a power peaking device (like a flywheel or ultracapacitor) and used as required to meet the tractive drive requirements (plus accessory loads) through an electrical motor. The engine/generator is stopped whenever the energy storage device is fully charged. Engine power output required was determined with a vehicle simulation code to be 15 to 20 kW steady state with peak output of 40 to 45 kW for hill climb. Combustion chamber and engine geometry were determined from a critical review of the hydrogen engine experiments in the literature combined with a simplified global engine model. Two different engine ...
The DITE (Divertor Injection Tokamak Experiment) program has been undertaken to demonstrate the feasibility of impurity control by the use of a diverter in an injection-heated toroidal plasma configuration. Rather than behaving in accordance with neoclassical toroidal containment theory, the plasma is subject to various instabilities, particularly the resistive fluid MHD types, follows the empirical scaling of energy confinement time with plasma parameters observed in other plasma devices. DITE experiments have, however, extended the range of current and density. Impurities arising from plasma interactions with the vacuum vessel surface are controlled by the bundle divertor, which diverts a portion of plasma and power in the plasma scrape-off layer into a separate target chamber where impurities can be removed. Auxiliary plasma heating is provided by the injection of powerful beams of neutral hydrogen atoms produced by multi-aperture ion sources and ...
Cryogenic distillation is the main industrial method for separating hydrogen's isotopes, because it presents the advantage of high separating factors and also the possibility of processing great quantities of gases. In the case of multicomponent mixtures the determination of transport for molecular species between the two phases is very difficult owing to the particularities of physical characteristics of each component from the mixture. The transport of molecular species is also strongly influenced by the hydrodynamics of two phases, in strong connection with the dimension of the interface between the vapor and liquid phase. The characteristics of the interface depend on the type and geometry of the separation area: plates or package. The traditional methods of analysis for exchange processes use the concept 'theoretic plate', a physical entity for which the values of concentrations for vapors and liquid that leaves the plate are in ...
We present results from a large volume simulation of Hydrogen reionization. We combine 3d radiative transfer calculations and an N-body simulation, describing structure formation in the IGM, to detail the growth of HII regions around high redshift galaxies. Our simulation tracks 1024^3 dark matter particles, in a box of side length 65.6 Mpc/h. This large volume allows us to accurately characterize the size distribution of HII regions throughout most of the reionization process. At the same time, our simulation resolves many of the small galaxies likely responsible for reionization. It confirms a picture anticipated by analytic models: HII regions grow collectively around highly-clustered sources, and have a well-defined characteristic size, evolving from a sub-Mpc scale at the beginning of reionization to R>10 Mpc towards the end. We present a detailed statistical description of our results, and compare them with a numerical hybrid scheme ...
Interest in renewable energy systems that employ regenerative components to enable intermittent energy sources to service time varying loads is growing. The overall performance of these systems is intimately linked to the choice of the energy storage media and the efficiency of the energy conversion devices. Recent advances in electrolyser and fuel cell technologies may make small-scale hydrogen buffered renewable energy systems a practical reality in the near term. A research team at the University of Victoria - Institute for Integrated Energy Systems (IESVic) is developing a flexible distributed, laboratory-scale energy system called IRENE (Integrated Renewable Energy Experiment). The initial goal of this research is to explore the potential for constructing a regenerative energy system using early commercial and precommercial hydrogen storage and fuel cell energy conversion devices. Once implemented, research efforts will focus on the ...
Precise measurements of the single spin asymmetry AN, and the double spin asymmetry ANN, in proton-proton (pp) elastic scattering in the region of four-momentum transfer squared 0.0012 have been performed using a polarized atomic hydrogen gas jet target and the Relativistic Heavy Ion Collider (RHIC) polarized proton beam. We present measurements of AN and ANN at center-of-mass energies ?(s)=6.8 and 13.7 GeV. These spin-dependent observables are sensitive to the poorly known hadronic spin-dependent amplitudes. Comparing AN at different energies, a ?(s) dependence of the hadronic single spin-flip amplitude is suggested. A hadronic double spin-flip amplitude from the ANN data is consistent with zero within a 2-? level. We also present ??T, estimated from the measured ANN data. The results for ??T are consistent with zero. Our results provide significant constraints toward a comprehensive understanding of the reaction mechanism for pp elastic ...
Topics related to aerospace power are discussed, taking into account trends and issues of military space power systems technology, space station power system advanced development, the application and use of nuclear power for future spacecraft, the current status of advanced solar array technology development, the application of a parabolic trough concentrator to space station power needs, life test results of the Intelsat-V nickel-cadmium battery, and metal hydride hydrogen storage in nickel hydrogen batteries. Other subjects explored are concerned with alternative fuels, biomass energy, biomedical power, coal gasification, electric power cycles, and electric propulsion. Attention is given to an advanced terrestrial vehicle electric propulsion systems assessment, fuel cells as electric propulsion power plants, a sinewave synthesis for high efficiency dc-ac conversion, steam desulfurization of coal, leadless transfer of ...
Direct electrochemistry and electrocatalysis of catalase (Cat) was studied based on a nano-composite film consisting of amine functionalized graphene and gold nanoparticles (AuNPs) modified glassy carbon electrode. Graphene was synthesized chemically by Hummers and Offeman method and then was functionalized with amino groups via chemical modification of carboxyl groups introduced on the graphene surface. The nano-composite film showed an obvious promotion of the direct electron transfer between Cat and the underlying electrode, which attributed to the synergistic effect of graphene-NH2 and AuNPs. The resultant bioelectrode retained its biocatalytic activity and offered fast and sensitive H2O2 quantification. Under the optimized experimental conditions, hydrogen peroxide was detected in the concentration range from 0.3 to 600 ?M with a detection limit of 50 nM at S/N = 3. The biosensor exhibited some advantages, such as short time respond (2 s), ...
This semiannual report for the period October 1983-March 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogentransfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: the use of pyrene as a chemical probe of catalyst activity; analysis of catalysts from Wilsonville run 242 using ESCA; atmospheric pressure model compound activity testing of regenerated catalysts from Wilsonville run 242; base displacement experiments with a coal-indole ...
This quarterly report for the period April through June 1984 summarizes activities in Sandia National Laboratories' continuing program of coal liquefaction research. The primary goals are to: explore novel catalytic concepts and materials for conversion of coal to liquid fuels; determine the effects of process variables on catalyst deactivation; determine the effects of coal structure and solvent properties on low temperature dissolution; study the kinetics and catalysis of hydrogentransfer reactions; develop an understanding of slurry gelling phenomena; and provide a technical assessment of coal liquefaction processes. During this period, work was performed on: analysis of catalyst samples from Wilsonville Run 246; catalyst presulfiding; catalyst activity testing using pyrene as a chemical probe; catalyst deactivation using a high-pressure model compound test reactor; dissolution chemistry of Wyodak coal; slurry gelling utilizing the ...
Since natural pyrite is easy to obtain and cheap as coal liquefaction catalyst, it is to be used for the 150 t/d scale NEDOL process bituminous coal liquefaction pilot plant. NEDO and NCOL have investigated the improvement of catalytic activity of pulverized natural pyrite for enhancing performance and economy of the NEDOL process. In this study, coal liquefaction tests were conducted using natural pyrite catalyst pulverized by dry-type bowl mill under nitrogen atmosphere. Mechanism of catalytic reaction of the natural pyrite was discussed from relations between properties of the catalyst and liquefaction product. The natural pyrite provided an activity to transfer gaseous hydrogen into the liquefaction product. It was considered that pulverized pyrite promotes the hydrogenation reaction of asphaltene because pulverization increases its contact rate with reactant and the amount of active points on its surface. It was ...
One important market related capability for firms which seek to develop radical innovations is the competence to involve the 'right' users at the 'right' time in the 'right' form. While former studies have identified a rather passive role of users in the radical innovation process, this paper focuses on the involvement of such users that are in the position to play an active role as inventors and (co)-developers. A multiple case study analysis was conducted in the field of medical technology. Five radical innovation projects within four firms were selected including medical robots and computer-assisted navigation systems. The case study analysis reveals that firms who closely interact with specific users benefit significantly for their radical innovation work. These users have a high motivation toward new solutions, are open to new technologies, possess diverse competencies, and are embedded into a very ...
The extracts from kinnow peel, kinnow seeds, litchi pericarp, litchi seeds, grape seeds, and banana peel were screened for total phenolic content (TPC), trolox equivalent antioxidant capacity (TEAC), 1,1 diphenyl-2-picryl hydrazyl (DPPH) radical scavenging activity, as well as reducing power. Kinnow peel extract exhibited the highest reducing power, TEAC, and DPPH free radical scavenging activity, whereas, the phenolic content of 37.4 mg GAE/g-dw was highest for grape seed extract. Banana peel extract with a low TPC showed the lowest reducing power, TEAC as well as DPPH free radical scavenging activity among the fruit residue extracts examined in the present study. Correlation analysis between the reducing power and DPPH radical scavenging ability; reducing power and ABTS radical scavengin...
Formation of oxidizing and reducing radicals was studied by pulse radiolysis of [Fe(CN)_6]"4"- - BrO_3"- - CN"- system in ethylene glycol - water solvent mixture. Oxidizing #centre dot#BrO_2 and BrO radicals formed by electron scavenging with #centre dot#BrO_2"- were identified and their reactions were investigated. The reaction of hydroxyl radicals with ethylene glycol leads to formation of reactive radicals with reducing properties and of compounds which reduce slowly in dark the ferricyanide formed in the reaction of #centre dot#BrO_2 radical with ferrocyanide. (author) 21 refs.; 7 figs.
Neopentane, because of its unique structural features, was found to be a useful probe for the assay of the acidity of various zeolites. The C-C bond was attacked by catalyst protons yielding CH/sub 4/ and the isobutyl carbenium ion in equal quantities. The latter either decomposed to produce isobutene or underwent secondary reactions. New avenues for reaction were opened with isobutane. The reaction of the Bronsted protons with the tertiary CH bonds produced H/sub 2/ and the same isobutyl carbenium ion. Hydride ion transfer of the same tertiary hydrogen to existing carbenium ions also occurred and the results showed that about half of the reaction was carried by this pathway. As with Neopentane, the C-C bond could also be attacked yielding the sec-propyl carbenium ion. These tools are being further developed.
The catalytic oxygen transfer properties of vanadium containing zeolites and vanadium based sol-gel catalysts with hydrogen peroxides are well known. The severe problem of vanadium leaching caused by the presence of the by-product water has been addressed. To avoid any interference with homogeneously catalyzed reactions, our study focusses on selective oxidations in a moisture-free medium with tert.-butylhydroperoxide. We have investigated the catalytic properties of amorphous microporous materials based on SiO{sub 2}, TiO{sub 2}, ZrO{sub 2} and Al{sub 2}O{sub 3} as matrix material and studied the effects of surface polarity on the oxidation of 1-octene and cyclohexane. (orig.)
A three-dimensional mathematical thermo-fluid model coupling the electrochemical kinetics with fluid dynamics was developed to simulate the heat and mass transfer in planar anode-supported solid oxide fuel cell (SOFC). The internal reforming reactions and electrochemical reactions of carbon monoxide and hydrogen in the porous anode layer were analyzed. The temperature, species mole fraction, current density, overpotential loss and other performance parameters of the single cell unit were obtained by a commercial CFD code (Fluent) and external sub-routine. Results show that the current density produced by electrochemical reactions of carbon monoxide cannot be ignored, the cathode overpotential loss is the biggest one among the three overpotential losses, and that the proper decrease of the operating voltage leads to the increase of the current density, PEN structure temperature, fuel utilization factor, fuel efficiency and power output of the ...
The exclusive electroproduction of ?0 mesons was studied with the HERMES spectrometer at the DESY laboratory by scattering 27.6 GeV positron and electron beams off a transversely polarized hydrogen target. Spin density matrix elements for this process were determined from the measured production- and decay-angle distributions of the produced ?0 mesons. These matrix elements embody information on helicity transfer and the validity of s-channel helicity conservation in the case of a transversely polarized target. From the spin density matrix elements, the leading-twist term in the single-spin asymmetry was calculated separately for longitudinally and transversely polarized ?0 mesons. Neglecting s-channel helicity changing matrix elements, results for the former can be compared to calculations based on generalized parton distributions, which are sensitive to the contribution of the total angular momentum of the quarks to the proton spin.
DMT has developed what is called the stepped reforming process. This is an allothermal gasification process which uses hydrogen for a gasification medium. First the biomass is pyrolised by means of a heat transfer material. The escaping gaseous and condensable constituents are hydrogenated, heated in a reforming stage and are made to react to a hydrogen-rich product gas by means of homogeneous gasification. The heat required for this is provided by burning the pyrolysis coke. This makes it possible to dispense with process stages that would involve gasification of solid material and hence require higher pressure levels. The present process also works at ambient pressure. Moreover, stepped reforming promises a number of additional advantages: low-tar product gas containing 60% hydrogen, high cold gas efficiency, no wastewater arisings, robust operating behaviour. This paper outlines ...
Radiation sterilization has several merits that it is a positively effective sterilization method, it can be used to sterilize low heat-resistant containers and high gas barrier films, and there is no possibility of residual chemicals being left in the packages. It has been commercially used in 'Bag in a Box' and some food containers. The #gamma# ray and an electron beam are commonly used in radiation sterilization. The #gamma# ray can sterilize large size containers and containers with complex shapes or sealed containers due to its strong transmission capability. However, since the equipment tends to be large and expensive, it is generally used in off production lines. On the other hand, it is possible to install and electron beam system on food production lines since the food can be processed in a short time due to its high beam coefficient and its ease of maintenance, even though an electron beam has limited usage such as sterilizing relatively thin materials and surface ...
The feasibility of using desferrioxamine (DF), an iron chelator, as a therapeutic agent against paraquat (PQ/sup + +/) toxicity in male Sprague-Dawley rats was explored, based on the rationale of limiting toxic hydroxyl radical production from hydrogen peroxide by removing redox-active iron. Body weights, mortality, and lung histopathology were followed for periods up to 14 days after intraperitoneal injection of PQ/sup + +/ (20 or 25 mg/kg body weight) with or without concurrent daily subcutaneous injections of DF (300 mg/day). Animals receiving PQ/sup + +/ showed the expected typical patterns of mortality and of lung histopathology, namely: marked edema, subpleural hemorrhage, acute inflammation, perivascular mononuclear cell infiltrates, sloughing of alveolar and bronchiolar lining cells, and diffuse interstitial fibrosis. Desferrioxamine alone was non-toxic. Surprisingly, results when both PQ/sup + +/ and DF were administered indicated a ...
General trends of developing hydrogen power engineering and technology in Ukraine are considered. Based on a general level of power consumption and real opportunities for hydrogen production, a conclusion is derived that there are possibilities in the near future to partially replace conventional hydrocarbon fuels by hydrogen. Besides, developed technologies for burning hydrogenous gases and hydrogen-fuel systems when applied to transport installations allow one to improve essentially their power and ecological characteristics. 5 refs.
Radical cations of various 3-methylalkanes (C_6-C_1_4) have been produced and stabilized by #gamma#-irradiation of the corresponding neutral compounds in saturated chlorofluorocarbon and perfluorocarbon matrices at 77 K. The perfluorocarbon matrices appeared more suitable for studies of the lighter radical cations, whereas the chlorofluorocarbon matrices were more suited for studies of the heavier radical cations; intermediary cations could be studied in both types of matrices. After irradiation, electronic absorptions associated with both the matrix and the alkane additive were observed. Pure spectra of the 3-methylalkane radical cations were obtained by difference spectrometry, after selective elimination of these cations by illumination. The electronic absorption spectra of the 3-methylalkane radical cations consist in all cases of a single broad absorption band. The spectral ...
Hydrogen peroxide is a commonly used oxidizing agent with a variety of uses depending on its concentration. Ingestion of hydrogen peroxide is not an uncommon source of poisoning, and results in morbidity...Full Text Available
Trihydroxynaphthalene reductase catalyzes two intermediate steps in the fungal melanin biosynthetic pathway. The enzyme, a typical short-chain dehydrogenase, is the biochemical target of three commercial fungicides. The fungicides bind preferentially to the NADPH form of the enzyme. Three X-ray structures of the Magnaporthe grisea enzyme complexed with NADPH and two commercial and one experimental fungicide were determined at 1.7 {angstrom} (pyroquilon), 2.0 {angstrom} (2,3-dihydro-4-nitro-1H-inden-1-one, 1), and 2.1 {angstrom} (phthalide) resolutions. The chemically distinct inhibitors occupy similar space within the enzyme's active site. The three inhibitors share hydrogen bonds with the side chain hydroxyls of Ser-164 and Tyr-178 via a carbonyl oxygen (pyroquilon and 1) or via a carbonyl oxygen and a ring oxygen (phthalide). Active site residues occupy similar positions among the three structures. A buried water molecule that is ...
The use of aqueous methyldiethanolamine (MDEA) for selective removal of hydrogen sulfide from acid gas streams has been studied in a 2 inch column packed with 1/4 inch ceramic Intalox saddles. The column was operated in a counter-current, steady state fashion. The feed gas composition varied between 1 and 5 mole % hydrogen sulfide and between 0 and 50 mole % carbon dioxide. In order to assist the development of packed column absorption models, the rate at which pure carbon dioxide absorbs into 2 M MDEA was measured as a function of pressure, liquid flow rate and packed bed length. The importance of end effects was carefully evaluated. In addition, draining and tracer methods were used to estimate the amount of static holdup present in the column. Using classical draining methods, as much as 50 % of the total holdup was found to be static. However, according to the step decrease in tracer method, less than 5 % of the total holdup was static. ...
The mono- and intramolecular cation-radicals (CR) reactions of diethylmercury in the CFCl_3, CFCl_2CF_2Cl matrices and CF_2BrCF_2Br and CFCl_3 freons vitrified mixture (1:1) were studied through the EPR method. Formation of radical products of transformations of the initial CR diethylmercury (X-ray radiation dose - 100-200 Gy at the temperature of 293 K) was studied through the spin trap of 2.4.6 - tri-tret-butylnitrosebenzene.
The kinetics of HO{sub 2} radicals in UV-irradiated frozen dilute solutions of H{sub 2}O{sub 2} were followed by the ESR technique. Radical disproportionations at the irradiation temperature were found to be adequately described in terms of dispersive kinetics by a second-order equal-concentration kinetic equation with rate parameters changing non-monotonically in the temperature range 100-200 K. These changes are thought to occur due to well separated structural relaxation regions of polycrystalline ice in the above temperature range. (author).
''Hybrid'' hydrogen storage, where hydrogen is stored in both the solid material and as a high pressure gas in the void volume of the tank can improve overall system efficiency by up to 50% compared to either compressed hydrogen or solid materials alone. Thermodynamically, high equilibrium hydrogen pressures in metal-hydrogen systems correspond to low enthalpies of hydrogen absorption-desorption. This decreases the calorimetric effects of the hydride formation-decomposition processes which can assist in achieving high rates of heat exchange during hydrogen loading-removing the bottleneck in achieving low charging times and improving overall hydrogen storage efficiency of large hydrogen stores. Two systems with hydrogenation enthalpies close to -20kJ/mol H2 were studied to ...
PurposeTo conduct a retrospective analysis within a large university teaching hospital, comparing outcomes between patients receiving either radical surgery or radiotherapy as curative treatment for bladder cancer.Patients and MethodsBetween March 1996 and December 2000, 169 patients were treated radically for muscle-invasive bladder cancer. Data were collected from patient notes. Statistical analyses were performed using Kaplan-Meier methods and Cox proportional hazards regression analysis to compare radiotherapy and surgical outcome data.ResultsThere was no difference in overall, cause-specific, and distant recurrence-free survival at 5 years between the two groups, despite the radiotherapy group being older (median age, 75.3 years vs. 68.2 years). There were 31 local bladder recurrences...
ROBOT-ASSISTED RADICAL LAPAROSCOPIC PROSTATECTOMY WAKE FOREST UNIVERSITY BAPTIST MEDICAL CENTER WINSTON-SALEM, NC 00:00:08 ANTHONY ATALA, MD: I would like ...
Penile rehabilitation therapy following radical prostatectomy is a much debated topic. Erectile dysfunction is still a significant contributor to postoperative morbidity following radical prostatectomy, despite meticulous nerve-sparing technique. Secondary smooth muscle changes in the penis have been identified as the underlying causes of penile atrophy, veno-occlusive dysfunction, and fibrosis. Initial observations that intracavernous injection therapies used on a regular basis postoperatively resulted in improvements in the return of spontaneous erectile function led to the development of penile rehabilitation protocols. Chronic dosing of PDE-V inhibitors is now commonly used by urologists after radical prostatectomy. Despite the current enthusiasm of penile rehabilitation therapy, current scientific evidence with clinical trials is still limited. PMID:19255627
The Mitochondrial Free Radical Theory of Aging (MFRTA) is currently one of the most widely accepted theories used to explain aging....Full Text Available
The n3 and n4 vibrational transitions of CH3 and CD3 isolated in solid parahydrogen were studied by high-resolution infrared spectroscopy. The radicals were produced by in situ UV photolysis of methyl iodides trapped in solid parahydrogen. The observed spectra showed clear rotational fine structures, which were subjected to further splitting due to the electrostatic field of solid parahydrogen. The molecular constants and crystal field parameters of the radicals in solid parahydrogen were determined by analyzing the spectral structures of the n3 and n4 transitions of CD3 by the crystal field theory. The rotational constants of the CD3 radical were found to be only a few percent smaller than those in the gas phase. The determined crystal field parameters indicated significant quantum effect...
The antioxidant properties of magnolol and honokiol were evaluated in the experimental systems of reducing ONOO^- and ^1O"2, bleaching @b-carotene in linoleic acid (LH) emulsion, and trapping 2,2'-azinobis(3-ethylbenzothiazoline-6-sulfonate) cationic radical (ABTS^+?) and 2,2'-diphenyl-1-picrylhydrazyl radical (DPPH), and then were applied to inhibit the oxidation of DNA induced by Cu^2^+/glutathione (GSH) and 2,2'-azobis(2-amidinopropane hydrochloride) (AAPH). Magnolol and honokiol were active to reduce ONOO^- and ^1O"2. Honokiol showed a little higher activity to protect LH and to inhibit Cu^2^+/GSH-induced oxidation of DNA than magnolol. In addition, honokiol exhibited higher activities to trap ABTS^+? and DPPH than magnolol. In particular, honokiol trapped 2.5 radicals while magnolol o...
... turbine blade heat-transfer and study the heat-transfer augmentation in idealized geometry and its ... responsible for heat transfer augmentation. ...
Oregon State University (OSU) and the Pacific Northwest National Laboratory (PNNL) were funded by the U.S. Department of Energy to conduct research focused on resolving the key technical issues that limited the deployment of efficient and extremely compact microtechnology based heat actuated absorption heat pumps and gas absorbers. Success in demonstrating these technologies will reduce the main barriers to the deployment of a technology that can significantly reduce energy consumption in the building, automotive and industrial sectors while providing a technology that can improve our ability to sequester CO{sub 2}. The proposed research cost $939,477. $539,477 of the proposed amount funded research conducted at OSU while the balance ($400,000) was used at PNNL. The project lasted 42 months and started in April 2001. Recent developments at the Pacific Northwest National Laboratory and Oregon State University suggest that the performance of absorption and desorption systems can be ...
At HMC, fundamental research on the hydrogen fueled engine and vehicle has been carried out. For this engine, solenoid driven injector is used to supply gaseous hydrogen into the cylinder and various operating parameters have been changed to study the combustion characteristics of hydrogen. After these experiments on the engine, a hydrogen fueled vehicle has been constructed and it is controlled by an ECU. The amount of emission from the hydrogen vehicle with stoichiometric operation is less than 1/3 of the ULEV legislation.
Decomposition yields of tetracycline sulphate and oxytetracycline sulphate were determined in argon saturated 0.1N H/sub 2/SO/sub 4/ solutions. The decomposition yields of teracyclines decrease in the presence of the Cl/sup -/ ions. The reaction rate constants of the OH radicals with tetracyclines were also determined.
Esters of dihydric alcohols with alkenylphosphonic or alkenylphosphinic acids which are polymerizable by free radicals are described. They are combined with polymer binders, in particular water-soluble polymers, and photoinitiators forming free radicals to give photopolymerizable mixtures which are suitable for the production of photoresists and printing plates. The mixtures display low heat-sensitivity and have long shelf lives. (author) 1 tab.
Practical procedures were developed for large-scale microbial decontamination of dry egg powder and gelatine with gamma radiation ("6"0Co). The formation and lifes of free organic radicals in these materials were examined by ESR measurements of powder samples. The concentration of these radicals was studied in dependence on the time of storage. Secondary oxidation of egg fats by air oxygen was investigated. Sensoric tests of irradiated gelatine, both in powder and hydrogel form, were performed. (author). 4 figs., 2 tabs., 2 refs.
The author is exploring the efficiency of pulsed plasma processing in the removal of nitrogen dioxide, nitrogen oxide, and other pollutants. This process uses an electrical discharge to create chemical radicals from air molecules. These radicals can react with pollutants and form harmless compounds. Additives such as hydrocarbons are also used to improve the efficiency of the removal. The efficient removal of nitrogen dioxide has required the presence of dilute aqueous solution of ammonia.
The high-energy radiation-induced degradation of an H-acid derivative azo dye, Apollofix-Red SF-28 (AR-28) was studied in aqueous solution by using pulse radiolysis with kinetic spectroscopic detection for transient measurements. Gamma radiolysis with UV-VIS spectroscopy and gradient ionpair HPLC separation with diode array detection were applied for following the destruction of AR-28 and measuring the products. The reactions of hydrated electron (e_a_q "-) and hydroxyl ("#centre dot#OH) radical were investigated separately. "#centre dot#OH reacts with the unsaturated bonds of the molecule. In the further reactions of the "#centre dot#OH adduct radicals, the AR-28 molecules partly reform with a slightly modified structure. The products formed in the first reaction of "#centre dot#OH and AR-28 molecules have also high reactivity towards the "#centre dot#OH radicals. For these reasons the efficiency of "#centre dot#OH ...
A proton exchange membrane fuel cell (PEMFC) must maintain a balance between the hydration level required for efficient proton transfer and excess liquid water that can impede the flow of gases to the electrodes where the reactions take place. Therefore, it is critically important to understand the two-phase flow of liquid water combined with either the hydrogen (anode) or air (cathode) streams. In this paper, we describe the design of an in situ test apparatus that enables investigation of two-phase channel flow within PEMFCs, including the flow of water from the porous gas diffusion layer (GDL) into the channel gas flows; the flow of water within the bipolar plate channels themselves; and the dynamics of flow through multiple channels connected to common manifolds which maintain a uniform pressure differential across all possible flow paths. These two-phase flow effects have been studied at relatively low operating temperatures under ...
This paper proposes a model to explain tritium release behavior of an irradiated Li_4SiO_4 sample made by Forschungszentrum Karlsruhe. The release curves were obtained in a series of experiments carried out using out-pile temperature programmed desorption techniques in the Kyoto University Reactor (KUR). Tritium release curves obtained for different purge gas compositions (N_2, N_2 + H_2, N_2 + H_2O) were compared for selection of suitable conditions to determine the apparent diffusivity of tritium in a crystal grain of Li_4SiO_4.In the model formation, some mass transfer steps in the bulk of the crystal grain and those on the surface of the grain were taken into account, which were diffusion of tritium in the grain, adsorption and desorption of water on the surface of the grain, two types of isotope exchange reactions, and water formation reaction by the addition of hydrogen to the purge gas.Diffusivities of tritium in the crystal grain of ...
Catalytic reactions of 3-methylpentane and 2,3-dimethylbutane on HY, amorphous silica-alumina, and HZSM-5 have been studied at 500{degree}C. Both kinetic phenomena and product selectivities have been reported. Cracking reactions an HZSM-5 can be attributed to initiation through protonation occurring at Bronsted sites. Bimolecular processes leading to chain reaction via hydride transfer are restricted within the narrow pore pentasil zeolite. On HY and amorphous silica-alumina, initiation of cracking also occurs at Bronsted sited. No direct evidence was found for participation of Lewis acid sites on the catalyst framework itself. Following initiation, reactions on these catalysts are accelerated through a chain process occurring at Lewis sites generated by adsorption of product olefins at Bronsted sites. The resulting change in the dominant cracking mechanism is reflected in the product selectivity, illustrated here by a falling off in formation of molecular ...
Abstract in english Higher olefins are produced as a by product in a number of refinery processes and are one of the potential raw materials to produce propylene. In the present study, FCC model feed compound was considered to explore the olefin cracking features and options to enhance propylene using 30% SAPO-34 zeolite as catalyst in a micro-reactor. The superior selectivity of propylene (73 wt%) and higher total olefin selectivity was obtained over 30% SAPO-34 catalyst than over Y or ZSM- (more) 5 zeolite catalysts. The thermodynamical constraints were found to be relatively less serious in the case of 1-hexene conversion. Most of the 1-hexene follows a direct cracking pathway to give two propylene molecules, due to weak acid sites and better diffusion opportunities. The higher temperature and short residence time could also suppress the hydrogentransfer reactions. From OPE (olefins performance envelop) the products were classified as ...
Biosorption of the heavy metal ion Cd{sup 2+} by protonated nonliving brown alga Sargassum fluitans biomass was accompanied by the release of hydrogen protons from the biomass. The uptake of cadmium and the release of proton matched each other throughout the biosorption process. The end-point titration methodology was used to maintain the constant pH 4.0 for developing the dynamic sorption rate. The sorption isotherm could be well represented by the Langmuir sorption model. A mass transfer model assuming the intraparticle diffusion in a one-dimensional thin plate as a controlling step was developed to describe the overall biosorption rate of cadmium ions in flat seaweed biomass particles. The overall biosorption mathematical model equations were solved numerically yielding the effective diffusion coefficient D{sub e} about 3.5 {times} 10{sup {minus}6} cm{sup 2}/s. This value matches that obtained for the desorption process and is approximately ...
This report details the status of the Biological Conversion of Synthesis Gas Project. The following tasks are described as being completed: (1) the test plan, (2) culture development, and (3) the mass transfer/kinetic studies. The bioreactor studies (Task 4) are underway. The continuous stirred tank reactor system for the conversion of H{sub 2}S to elemental sulfur using Chlorobium thiosulfatophilum has been studied for varying light intensities. The system was also modified to include both sulfur recovery and cell recycle using ceramic membranes. Studies were also performed to observe the effects of cell recycle using a polysulfone hollow filter membrane module. Work on Task 5, limiting conditions/scale-up, includes a scale-up study with three different size reactors to establish the optimum operating conditions for hydrogen production from synthesis gas by the biological water-gas shift reaction using the photosynthetic bacterium ...
The purpose of this research is to develop a technically and economically feasible process for biologically producing H(sub 2) from synthesis gas while, at the same time, removing harmful sulfur gas compounds. Six major tasks are being studied: 1. Culture development, where the best cultures are selected and conditions optimized for simultaneous hydrogen production and sulfur gas removal; 2. Mass transfer and kinetic studies in which equations necessary for process design are developed; 3. Bioreactor design studies, where the cultures chosen in Task 1 are utilized in continuous reaction vessels to demonstrate process feasibility and define operating conditions; 4. Evaluation of biological synthetic gas conversion under limiting conditions in preparation for industrial demonstration studies; 5. Process scale-up where laboratory data are scaled to larger-size units in preparation for process demonstration in a pilot-scale unit; and 6. Economic ...
The investigations showed that the new adsorber/catalyst composites are well suited for chemical degradation of persistent water pollutants. Compared with alternative processes, the reaction selectivity and the consumption of oxidant are more favourable as the reaction now takes place on/inside the solid. The process, which was developed originally for purification of contaminated water, can be transferred to many other systems of materials. For example, it is expected that the soot emissions of diesel engines will be reduced significantly after efficient hydrogenation of the aromatics contained in the diesel engine on molybdenum-charged mesoporous composites. [German] Mit den vorliegenden Untersuchungen konnte ein erster Nachweis gefuehrt werden, dass die neu entwickelten Adsorber/Katalysator-Komposite fuer den chemischen Abbau persistenter Wasserschadstoffe geeignet sind. Im Vergleich zu alternativen Verfahrensloesungen kann die Selektivitaet ...
Neutron radiography and neutron radioscopy are rapidly becoming the valuable tools for nondestructive testing and basic research. The Phoenix Memorial Laboratory has developed a neutron facility capable of both film neutron radiography and real time neutron radioscopy, and has used this facility to study several phenomena of interest to the researchers in many areas. Neutrons can be used for imaging the phenomena that X-ray cannot image, such as the presence, absence or movement of hydrogenous materials inside metals such as aluminum or steel. There are three basic methods for obtaining images using neutrons: high resolution film neutron radiography, real-time neutron radioscopy and transfer film neutron radiography. The neutron radiography facility at Phoenix Memorial Laboratory, the neutron radioscopic imaging systems, the neutron radiographic detectors, lubrication studies, spray imaging, flow in porous media, three-dimensional ...
It has been reported by the present authors that behavior of tritium release from solid breeder grain is consisted of diffusion in grain, tritium transfer at surface layer and surface reactions on grain surface such as adsorption or isotope exchange reactions. Tritium release curves estimated using the tritium release model gave good agreement with observed tritium release curves from Li{sub 4}SiO{sub 4}, Li{sub 2}ZrO{sub 3} or LiAlO{sub 2}. Tritium release behavior from Li{sub 2}TiO{sub 3} under humid purge gas, dry purge gas and dry purge gas with hydrogen conditions is discussed in this study, tritium release curves using the release model that we proposed previously give a good agreements with experimental tritium release curves. Tritium effective diffusivity in the crystal grain of Li{sub 2}TiO{sub 3} is also estimated in this study using a curve-fitting method applied to the release curves obtained under the humid purge gas condition. It ...
It has been reported by the present authors that behavior of tritium release from solid breeder grain is consisted of diffusion in grain, tritium transfer at surface layer and surface reactions on grain surface such as adsorption or isotope exchange reactions. Tritium release curves estimated using the tritium release model gave good agreement with observed tritium release curves from Li_4SiO_4, Li_2ZrO_3 or LiAlO_2. Tritium release behavior from Li_2TiO_3 under humid purge gas, dry purge gas and dry purge gas with hydrogen conditions is discussed in this study, tritium release curves using the release model that we proposed previously give a good agreements with experimental tritium release curves. Tritium effective diffusivity in the crystal grain of Li_2TiO_3 is also estimated in this study using a curve-fitting method applied to the release curves obtained under the humid purge gas condition. It is discussed that change of color of ...
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary experiments in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The experiments were run on the Parallel Channel Test Loop (PACTEL), which is a medium scale integral test facility designed to simulate thermal-hydraulic phenomena characteristic of VVER 440 type nuclear plants. The experiments aimed at studying the effect of noncondensable gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators (ACCU) released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any noncondensable gas in all cases where cooling is ensured by natural circulation. This paper presents the measured results of the series of three ...
Six intermetallic alloys (CeNi/sub 5/, MmNi/sub 5/, Ca/sub 0/ /sub 2/(Ce/sub 0/ /sub 65/Mm/sub 0/ /sub 35/)/sub 0/ /sub 8/Ni/sub 5/, Ca/sub 0/ /sub 2/Ce/sub 0/ /sub 8/Ni/sub 5/, Ca/sub 0/ /sub 2/Mm/sub 0/ /sub 8/Ni/sub 5/, and a mixed alloy, CeNi/sub 5//MmNi/sub 5/) were investigated with respect to their suitability to provide high hydrogen capacity and their potential for use in providing substantial hydrogen pressure at both low and high temperatures. A second phase of our investigation dealt with ball-milling and hydriding and dehydriding cycles to produce fine particles for use in hydride powder transfer studies. A summary of several Van't Hoff plots is also included for hydride-forming alloys.
Anionic complexes of transition metals were stabilized in aqueous solutions containing high concentrations of various short-chain quaternary ammonium salts. Compounds with longer paraffin chains were effective in much less concentrated solution. Complex ions were detected spectrophotometrically. FeCl/sub 4//sup -/, which is usually formed in concentrated HCl, was the predominant Fe(III) complex in 30 m choline chloride containing only 0.12 M HCl. A yellow transitory Tc(VII) chloro-addition intermediate, formed in the reduction of TcO/sub 4//sup -/ by concentrated HCl, was stabilized when the solution also contained 25 m choline chloride. Its spectrum, as well as the isolation of an already known Tc(VII) bipyridyl complex, is reported. Concentrated organic electrolytes also stabilized Tc(V) oxide halides against disproportionation and Tc(IV) hexahalides against hydrolysis. Halochromates of Cr(VI) were formed and stabilized in dilute acid containing quaternary ammonium salts. Their UV ...
We investigate the evolution of Type Ib/c supernova (SN Ib/c) progenitors in close binary systems, using new evolutionary models that include the effects of rotation, with initial masses of 12-25 M_s_u_n for the primary components, and of single helium stars with initial masses of 2.8-20 M_s_u_n. We find that, despite the impact of tidal interaction on the rotation of primary stars, the amount of angular momentum retained in the core at the presupernova stage in different binary model sequences converges to a value similar to those found in previous single star models. This amount is large enough to produce millisecond pulsars, but too small to produce magnetars or long gamma-ray bursts. We employ the most up-to-date estimate for the Wolf-Rayet mass-loss rate, and its implications for SN Ib/c progenitors are discussed in detail. In terms of stellar structure, SN Ib/c progenitors in binary systems at solar metallicity are predicted to have a wide range of final masses up to about 7 ...
Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions.
Hydrogen uptake and embrittlement of tantalum by electrolytically produced hydrogen is investigated on samples of varying composition and type of pretreatment. Of decisive influence on the uptake of hydrogen are the oxide layers present on the tantalum surface. By contact with platinum group metals as alloying constituents, surface coatings or anodic protection, a protection of tantalum can be obtained depending on the experimental conditions. (orig.).
Aqueous deoxyhemoglobin solutions (2 mg/ml) were gamma-irradiated by a "6"0Co source in the presence of methanol, ethanol, 1-butanol and t-butanol under N_2O or argon. The effects of the interaction of the particular alcohol radical species with hemoglobin were determined according to the detected spectral alterations in the visible range. The amounts of stable final products in the form of methemoglobin (MetHb) and the sum of hemichromes and cholehemichromes (Hemichr) were estimated in irradiated preparations. For preparations irradiated under N_2O, the radiation yield for MetHb formation was three-fold lower in the presence of ethanol and 1-butanol [G(MetHb) = 0.33[ compared with preparations irradiated in the presence of t-butanol or without alcohol [G(MetHb) = 1.00[. The yield of hemichromes and cholehemichromes in preparations irradiated under N_2O increased in the order: ethanol (G = 0.38), 1-butanol (B = 0.52), t-butanol (G = 0.59), and in the absence of ...
The Institute of Energetic and Nuclear Research - IPEN is a research and development institution, located in a densely populated area, in the city of Sao Paulo. The nuclear fuel cycle was developed from the Yellow Cake to the enrichment and reconversion at IPEN. After this phase, all the technology was transferred to private enterprises and to the Brazilian Navy (CTM/SP). Some plants of the fuel cycle were at semi-industrial level, with a production over 20 kg/h. As a research institute, IPEN accomplished its function of the fuel cycle, developing and transferring technology. With the necessity of space for the implementation of new projects, the uranium hexafluoride (UF{sub 6}) production plant was chosen, since it had been idle for many years and presented potential leaking risks, which could cause environmental aggression and serious accidents. This plant decommission required accurate planning, as this work had not been carried out in ...
Lappeenranta University of Technology (LTKK) and VTT Energy carried out a series of preliminary tests in 1999 to study the behavior of noncondensable (NC) gases in VVER geometry. The tests aimed at studying the effect of NC gases on system thermal-hydraulics and on heat transfer in a horizontal steam generator (HSG). The system behavior can be affected by hydrogen produced in the core in case of a severe accident, by nitrogen from hydro-accumulators released into the primary circuit in case of a loss-of-coolant accident (LOCA) and more generally by any NC gas in all cases where cooling is ensured by natural circulation. A secondary objective of the tests - the first series of tests ever performed with NC gas with PACTEL - was to find out, if the instrumentation of PACTEL was adequate for this type of tests and if it was functioning properly. This paper presents the measured and calculated (CATHARE code version V15a mod 2.1) results of the test ...
The pathway to hydrogen generation entirely from renewable energy and material sources probably goes by a transitional period with the utilization of hybrid fossil/renewable integrated systems. Solar steam reforming of methane is set in this context, specifically suited for a country like Italy whose actual energy policy is mainly based on the imported NG, but also characterized by convenient solar radiation levels in the Southern Regions. A new solar SMR process is being developed by ENEA, using molten nitrates as solar heat carriers and storage medium at about 550 C. The potential of this process have been proved theoretically by process simulation studies. Engineering and experimental activities aimed to the development of a prototype apparatus are now in progress in ENEA's laboratories. It is remarkable that the developed technology (MS powered SMR) can find interesting impact in the in industrial chemistry wherever it is convenient decoupling the heat ...
Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging caused by the build up ...
NUPEC has carried out hydrogen mixing tests to investigate hydrogen distribution behavior within a model containment and to provide a set of experimental data for validation of severe accident analysis codes.
A synthetic strategy for constructing ionic hydrogen-bonded materials by combining perhalometallate anions with cations able to serve as hydrogen bond donors is presented. The approach is based on identification...Full Text Available
The effects of the plasma nitriding with the formation of compound nitride and diffusion zones and of the boronising with the different ion doses on hydrogen distribution and hydrogen induced deterioration of a surface layer were examined in the case of Armco iron. Electrochemical studies of hydrogen permeation rate, hydrogen vacuum extraction measurements, optical and scanning microscopy, X-ray diffraction and elastic recoil detection analysis (ERDA) were used. Accumulation of entering hydrogen within the various constituent zones of the modified layer inhibits the hydrogen transport into the metal and thus, decreases the mean hydrogen content in the deeper zones and in the core. Hydrogen accumulation within the compact nitride zone causes the expansion of the nitride lattice, nitride phase transformation and ...
Kinetics of postradiation polymerization of triethylene glycol ..cap alpha.., ..omega..-dimethacrylate has been studied by calorimetric method. The low-temperature radiolysis has been studied by ESR method. The radiation-chemical yield of radicals on ..gamma..-irradiation by /sup 60/Co is determined being equal to 6+-1 1/100 ev. Transformation of the radicals spectrum into the spectrum of propagating macroradicals proceeds at 140 K. After the transition from glassy to liquid state (Tsub(g)=193 K) the intensive postpolymerization begins. During the polymerization the disappearance of radicals is observed. For the low-temperature region the effective activation energy of polymerization is determined beina equal to 50.7+-0.8 kJ/mol.
Pulse radiolysis studies of the formation kinetics and the yields of various phenylcarbenium ions from several different solutes in 1,2-dichloroethane solution have been carried out. The results indicate that there are two kinetically distinguishable cationic species of the solvent which react selectively with the different solutes to form the phenylcarbenium ions. It is suggested that one is a cation radical (yield 0.68 molecule/100 eV) and the other a carbocation (yield 0.20 molecule/100 eV). Rate constants for their separate reactions with selected aromatic compounds and with ammonia have been determined. Molar extinction coefficients have been estimated for benzyl cation, diphenyl cation radical, and anthracene cation radical. 6 figures, 1 table.
Pulse radiolysis studies of the formation kinetics and the yields of various phenylcarbenium ions from several different solutes in 1,2-dichloroethane solution have been carried out. The results indicate that there are two kinetically distinguishable cationic species of the solvent which react selectively with the different solutes to form the phenylcarbenium ions. It is suggested that one is a cation radical (yield 0.68 molecule/100 eV) and the other a carbocation (yield 0.20 molecule/100 eV). Rate constants for their separate reactions with selected aromatic compounds and with ammonia have been determined. Molar extinction coefficients have been estimated for benzyl cation, diphenyl cation radical, and anthracene cation radical. 6 figures, 1 table.
The effects of TANOL radical have been examined on chemical shifts and relaxation rates of /sup 109/Ag NMR in aqueous solution of silver salts. The silver ion in aqueous solution is found to coordinate with TANOL radical. A small amount of TANOL is added as a doping agent(0.020M), since /sup 109/Ag signals are obtained for (1.0M) silver ion within 30 minutes. The /sup 109/Ag chemical shifts of silver salt in aqueous solutions were found within the range of 0 to -1000 ppm relative to that of 1.0M AgNo/sub 3/.
An integrated approach to the modelling of hydrogen assisted failure in 316L steel is presented. The approach includes experimental, fractographic, numerical and theoretical analysis of the phenomenon. The physical adequacy of the mechanical models of hydrogen embrittlement (notch extension model and notch cracking model) is discussed by comparing the virtual damage depth (theoretical) predicted by the models with the embrittled zone (microphysical) measured in the fractographic analysis by scanning electron microscopy. In addition, a numerical modelling of hydrogen diffusion is performed, concluding that bulk diffusion is not important in hydrogen embrittlement of 316L steel, so that hydrogen transport accelerated by the microdamage itself should be taken into account. (orig.)
This is the first text and reference book to be devoted completely to the very important and timely subject of heat transfer augmentation. This book is of equal appeal to both researchers and designers of heat transfer equipment.
The article presents briefly the plans of the British Petroleum Oil Company for a new hydrogen power plant that includes an offshore platform in the North Sea.
Woolfolk, C. A. (University of Washington, Seattle). Reduction of inorganic compounds with molecular hydrogen by Micrococcus lactilyticus. II. Stoichiometry with inorganic...Full Text Available
Exercise training is known to induce an increase in free radical production potentially leading to enhanced muscle injury. Vitamins C and E are well known antioxidants that may prevent muscle cell damage....Full Text Available
Exposure of albumin to Cu(II) (10-100 microM) and ascorbate (0.1-2 mM) results in extensive molecular modifications, indicated by decreased fluorescence and chain breaks. The rate of utilization of...Full Text Available
The authors report on a search for pair production of first-generation scalar leptoquarks (LQ) in p{bar p} collisions at {radical}s = 1.96 TeV using an integrated luminosity of 252 pb{sup -1} collected at the Fermilab Tevatron collider by the D0 detector. They observe no evidence for LQ production in the topologies arising from LQ{ovr LQ} {yields} eqeq and LQ{ovr LQ} {yields} eqvq, and derive 95% C.L. lower limits on the LQ mass as a function of {beta}, where {beta} is the branching fraction for LQ {yields} eq. The limits are 241 and 218 GeV/c{sup 2} for {beta} = 1 and 0.5, respectively. These results are combined with those obtained by D0 at {radical}s = 1.8 TeV, which increases these LQ mass limits to 256 and 234 GeV/c{sup 2}.
Our group has developed a physician-operated inpatient order-entry system (BICS-OE). Mindful of the problems inherent in bringing a radical cultural change such as this to the hospital, we conducted...Full Text Available
BackgroundThe optimal treatment for locally recurrent rectal cancer (LRRC) is still a matter of debate. This study assessed the outcome of LRRC patients treated with multimodality...Full Text Available
Background. The Free Radical Theory of Aging mechanistically links oxidative stress to aging. Okinawa has among the world's longest-lived populations but oxidative stress in this...Full Text Available
Recurrent tumour after radical pancreaticoduodenectomy may cause obstruction of the small bowel loop draining the liver. Roux-loop obstruction presents a particular therapeutic challenge, since the...Full Text Available
The CNS can exhibit features of inflammation in response to injury, infection or disease, whereby resident cells generate inflammatory mediators, including cytokines, prostaglandins, free radicals and...Full Text Available
Because copper catalyzes the conversion of H2O2 to hydroxyl radicals in vitro, it has been proposed that oxidative DNA damage may be an important component of copper toxicity....Full Text Available
SUMMARYA gene eam in Clostridium difficile encodes a protein that is homologous to lysine 2,3-aminomutase (LAM) in many other species but does...Full Text Available
By using EPR measurements of radiation-induced radicals it is possible to utilize human fingernails to estimate radiation dose after-the-fact. One of the potentially limiting factors in this...Full Text Available
The dissociation of methylal is investigated using mass spectrometry, combined with a pyrolytic radical source and femtosecond pump probe experiments. Based on preliminary results two reaction paths of methylal dissociation are proposed and discussed. (author) 4 fig., 3 refs.
ObjectiveThe aim of this study was to ascertain whether all cervical cancer patients who received adjuvant concurrent chemoradiation (CCRT) for high risk of treatment failure after...Full Text Available
The development of detailed chemical kinetic reaction mechanisms for oxidation of n-octane and iso-octane is described, with emphasis on the factors which are specific to many large hydrocarbon fuel molecules. Elements which are of particular importance are found to include site-specific abstraction of H atoms, radical isomerization of alkyl radicals by internal H atom abstraction, and rapid ..beta..-scission of the alkyl radicals. These features, combined with distinctions in the types of intermediate olefin species produced, are used to explain the significant differences in the rate of oxidation between n-octane and iso-octane. Experimental results from the turbulent flow reactor and low pressure laminar flames, using both n-octane and iso-octane as fuels, are used to test the reaction mechanisms and indicate those parts of the total mechanisms which are in greatest need of further development and refinement. It is found ...
Two additional hyperfine components of the interstellar radical C3H were detected. In addition, methanol was discovered in interstellar clouds. The abundance of HCCN and various chemical isomers in molecular clouds was investigated.
OBJECTIVE: To test the hypothesis that perioperative transfusion of allogeneic and autologous red blood cells (RBCs) stored for a prolonged period speeds biochemical recurrence of prostate cancer...Full Text Available
The free radical theory of ageing posits that accrual of oxidative damage underlies the increased cellular, tissue and organ dysfunction and failure associated with advanced age. In support of this...Full Text Available
RC-12 [1,2-dimethoxy-4-(bis-diethylaminoethyl)-amino-5-bromobenzene] was evaluated for prophylactic, radical curative, and suppressive activities against infections with Plasmodium cynomolgi and subacute...Full Text Available
This volume is divided into the following sections: (1) fundamentals of convection heat transfer; (2) fundamentals of heat transfer with impinging jets; and (3) fundamentals of heat transfer augmentation. Separate abstracts were prepared for most papers in this volume.
Pulse radiolysis has been used to optically and kinetically characterize the transient free radicals formed by the reaction of H"s"m"-"b"u"l"l"e"t, N_3"s"m"-"b"u"l"l"e"t, or OH"s"m"-"b"u"l"l"e"t with 2,4,5-trichlorophenol (TCP-OH). The hydroxy-2,4,5-trichlorocyclohexadienyl radical (H-TCP-OH) formed by H"s"m"-"b"u"l"l"e"t addition to TCP-OH [k = (1.1 #+-# 0.2) x 10"9 M"-"1 s"-"1] has an absorption maximum at 360 nm with #epsilon#_3_6_0 = (4700 #+-# 1000) M"-"1 cm"-"1. The 2,4,5-trichlorophenoxyl radical (TCP-O"s"m"-"b"u"l"l"e"t) formed by the reaction of N_3"s"m"-"b"u"l"l"e"t with TCP-O- [k = (4.3 #+-# 0.8) x 10"9 M"-"1 s"-"1] has an absorption maximum at 430 nm with #epsilon#_4_3_0 = (3600 #+-# 600) M"-"1 cm"-"1. The dihydroxy-2,4,5-trichlorocyclohexadienyl radical (HO-TCP-OH) formed by OH"s"m"-"b"u"l"l"e"t radical addition to TCP-OH [k = (1.2 #+-# 0.1) x 10"1"0 M"-"1 s"-"1] has an ...
Chlorophyll a, chlorophyll b, and bacteriochlorophyll a in aqueous micellar solutions of Trition X 100 (2%) are readily oxidized by pulse-radiolytically generated N_3., Br_2"-., and (SCN)_2"-. radicals at nearly diffusion-controlled rates. The kinetic study suggests that pigment molecules occupy multiple sites in the micelle. Pheophytin a is only oxidized by N_3. and Br_2"-. radicals. The absolute spectra and the molar extinction coefficients of chlorophyll a, bacteriochlorophyll a, chlorophyll b, and pheophytin a cations have been determined. The chlorophyll a cation has been observed in the presence of pigment aggregates.
Forty-three patients with basal and squamous cell carcinomata arising on the pinna were treated radically using a 10 MeV electron beam. The technique and dosage are described and discussed. Primary cancer control with retention of the pinna was achieved in 34 patients. Salvage pinnectomy was performed in four patients for recurrence and one patient for radiation necrosis. Two patients with large primary tumours failed to resolve and died of their disease. The advantages for the patient of the policy of primary radical electron beam therapy are discussed.
The authors present a measurement of the B{sub s}{sup 0} meson lifetime using fully and partially reconstructed hadronic decays B{sub s}{sup 0} {yields} D{sub s}{sup -} {pi}{sup +}(X) followed by D{sub s}{sup -} {yields} {phi}{pi}{sup -}. The data sample was recorded with the CDF II detector at the Fermilab Tevatron and corresponds to an integrated luminosity of 1.3 fb{sup -1} from p{bar p} collisions at {radical}s = 1.96 TeV.
Purpose: To conduct a retrospective analysis within a large university teaching hospital, comparing outcomes between patients receiving either radical surgery or radiotherapy as curative treatment for bladder cancer. Patients and Methods: Between March 1996 and December 2000, 169 patients were treated radically for muscle-invasive bladder cancer. Data were collected from patient notes. Statistical analyses were performed using Kaplan-Meier methods and Cox proportional hazards regression analysis to compare radiotherapy and surgical outcome data. Results: There was no difference in overall, cause-specific, and distant recurrence-free survival at 5 years between the two groups, despite the radiotherapy group being older (median age, 75.3 years vs. 68.2 years). There were 31 local bladder recurrences in the radiotherapy group (24 solitary), but there was no significant difference in distant recurrence-free survival. In a more recent (2002-2006) ...
The Si-L X-ray emission spectrum of amorphous hydrogenated silicon (a-Si:H) is presented and discussed. For a qualitative interpretation of the measured spectra cluster calculations of pure Si clusters (SiSi4) and Si clusters with hydrogen (SiSi3H) have been performed using a simplified LCAO-X scheme. In general the level shifts caused by introduction of hydrogen are small compared with the valence band width.
The relationships of hydrogen alloyed #beta#-titanium alloy deformation behaviour to its microstructure and texture are investigated. It is shown that plasticity increases and strain induced texture changes at low hydrogen contents (0.1-0.2 mass %). Possible mechanisms responsible for specific features of #beta#-Ti alloy deformation are discussed. The study is made using alloy VT35 doped with hydrogen
The mid-range industrial market currently consumes 4.2 million metric tons of hydrogen per year and has an annual growth rate of 15% industries in this range require between 100 and 1000 kilograms of hydrogen per day and comprise a wide range of operations such as food hydrogenation, electronic chip fabrication, metals processing and nuclear reactor chemistry modulation.
It is shown that bending tests on microsamples can be used to study the conditions in which hydrogen brittleness develops. In such tests hydrogen brittleness develops in the VTI5 alloy within the temperature range +5 to -20"0C. The tendency of VTI5 to develop hydrogen brittleness is enhanced with bending in salt water. (author).
Hydrogenation of napthalene to tetralin using activated red mud as catalyst was studied as a typical hydrogen-donor system. Under the chosen reaction conditions, unprocessed red mud resulted in a conversion of napthalene of 3.55%. The most active catalyst, prepared by adding 20 wt% of TiO/SUB/2 to the red mud, followed by acid digestion and re-precipitation, resulted in a 58% conversion of naphthalene. This technology may have an important bearing on processes such as coal hydrogenation or crude-oil-residue processing, where the rate of reaction and product quality may depend upon the rate at which a hydrogen-donor solvent can be re-hydrogenated. (7 refs.)
The effect of various hydrogen concentrations on the crystal lattice period and the hardness of titanium alloy was examined, the alloy containing about 16 at.% Mo (27.5 wt. % Mo) and having #beta# structure. The peculiar features of the mechanism of plastic deformation of the alloy were studied after adding hydrogen to it. A dependence of the crystal lattice period on the concentration of hydrogen was obtained for TixMoxH_2 alloy. It has been established that the hardness of the Ti-Mo alloy does not change when hydrogen is added to it. The presence of hydrogen introduces changes into the mechanism of deformation of #beta#-titanium alloy. The configuration of the inverse pole figures after rolling proves that the transverse slip process in an alloy with hydrogen is hampered, and that the coplanar slip process is developing in it.
A study was made into microstructure and texture of cold rolled titanium alloy VT-35 with various hydrogen content aimed to reveal hydrogen influence on the mechanism of cold plastic deformation by rolling. Experiments were carried out using sheets 1.2 mm thick hydrogenated up to hydrogen concentrations from 0.06 to 0.554 mass. %. All specimens constituted a single-phase FCC #beta#-solid solution. It is shown that small hydrogen additions have a plasticizing effect on #beta#-titanium alloys in their cold rolling. The character of texture is dependent on hydrogen concentration and determined by deformation mechanism. 6 refs.; 5 figs.
A fractographic and numerical approach is presented to analyze hydrogen-plasticity interactions in pearlitic steel and to elucidate the main hydrogen transport mechanism in this material under triaxial stress states produced by notches. Fractographic analysis showed that the microdamage produced by the hydrogen was clearly detectable by scanning electron microscopy (SEM), through a specific microscopic topography associated with hydrogen effects (tearing topography surface or TTS). Numerical computations obtained by using an elastic-plastic finite element program gave the progressive spreading of the plastic zone, closely associated with the movement of dislocations. In the majority of cases, the plastic zone (PZ) clearly exceeds the hydrogen affected region (TTS) and has no relation with it. In some tests, however, the hydrogen-induced micro-damage surpasses ...
Hydrogen piston engines can be simultaneously optimized for improved thermal efficiency and for extremely low emissions. Using these engines in constant-speed, constant-load systems such as series hybrid-electric automobiles or home cogeneration systems can result in significantly improved energy efficiency. For the same electrical energy produced, the emissions from such engines can be comparable to those from natural gas-fired steam power plants. These hydrogen-fueled high-efficiency, low-emission (HELE) engines are a mechanical equivalent of hydrogen fuel cells. HELE engines could facilitate the transition to a hydrogen fuel cell economy using near-term technology.
We have investigated the stability and catalytic activity of epitaxial overlayers of rhodium on Au(111) and Pd(111). Both surfaces show a strong affinity for hydrogen. We have calculated the energy of adsorption both for a strongly and a more weakly adsorbed species; the latter is the intermediate in the hydrogen evolution reaction. Both the energy of activation for hydrogen adsorption (Volmer reaction) and hydrogen recombination (Tafel reaction) are very low, suggesting that these overlayers are excellent catalysts. PMID:21847482
Intermetallic compounds are regarded as highly promising for applications as high temperature structural materials. However, recent studies have demonstrated that a number of ordered alloys exhibit environmental embrittlement when tested in various environments at ambient temperature. When exposed to hydrogen gas or electrolytically charged with hydrogen, a significant ductility loss has been reported. The reaction of water vapor with reactive elements in the crack tip results in the generation of atomic hydrogen which diffuses from the surface to the interior and causes embrittlement. In this paper, the authors try to analyze the sensitivity of hydrogen embrittlement of ordered alloys based upon energetical considerations.
Earlier work carried out on the hydrogen-diesel dual-fuel engine indicates that knock sets in when the inducted hydrogen exceeds about 60% of input energy with a pilot quantity of 30% of full load diesel amount. Some of the findings of an investigation into knock-free performance of a hydrogen-diesel dual-fuel engine with the addition of a diluent-carbon dioxide are presented. The effects of carbon dioxide on the suppression of knocking in the hydrogen-diesel dual-fuel engine and on the improvement in the knock limited power output are described.
Insulated pressure vessels are cryogenic-capable pressure vessels that can be fueled with liquid hydrogen (LIQ) or ambient-temperature compressed hydrogen (CH2). Insulated pressure vessels offer the advantages of liquid hydrogen tanks (low weight and volume), with reduced disadvantages (lower energy requirement for hydrogen liquefaction and reduced evaporative losses). This paper shows an evaluation of the applicability of the insulated pressure vessels for light-duty vehicles. The paper shows an evaluation of evaporative losses and insulation requirements and a description of the current experimental plans for testing insulated pressure vessels. The results show significant advantages to the use of insulated pressure vessels for light-duty vehicles.
Various methods for storing hydrogen have been examined in an effort to find ways to store hydrogen in increasingly smaller volumes with decreasing weight of the whole hydrogen storage system. Metal hydrides, in which hydrogen is chemically bound to a metal atom, are considered to be very promising candidates for hydrogen storage because they have high gravimetric and volumetric storage capacities. This study investigated the effect of different magnesium (Mg) and aluminium (Al) ratios on the absorption and desorption properties of thin films. Neutron reflectometry (NR) was used in this study to better understand the absorption and desorption properties of commercially promising hydrogen storage materials. The large negative scattering length of hydrogen atoms changes the reflectivity curve substantially, so that NR can determine the total ...
The possibility of switching the heat transfer consists of varying heat transfer surfaces and making the heat transfer temporarily more intensive. Heat tubes prove to be particularly suitable, which must be exposed to a heat carrier fluid or removed from its effect for switching the heat transfer. This report gives a survey of the possibilities of switching heat flows and for making the heat transfer more intensive. Further, the report contains a survey of patents limited to heat transfer in the fields of cooling internal combustion engines and exhaust systems. (orig.) With 17 figs., 183 refs.
In this study, the effects of hydrogen peroxide on laminar, premixed, methane-air flames at atmospheric pressure and temperature were investigated using CHEMKIN III and GRI 3.5 mechanism. The range of fuel/air equivalence ratio {phi} was varied from 0.6 to 1.2, and the amount of hydrogen peroxide was altered from 0% to 20% volumetric fraction of the methane-hydrogen peroxide (air excluded) mixture. The burning velocity was found to increase with increasing hydrogen peroxide addition, with a relatively larger increase for the fuel-richer mixtures ({delta}S{sub u} up to 15 cm/s for {phi} {approx}=1.2). The adiabatic flame temperature rose with hydrogen peroxide addition, and the temperature rise per unit hydrogen peroxide addition was more significant ({delta}T up to 100 K) for the leaner mixtures. For the same mixture stoichiometry, adding ...
Full text of publication follows: The hydrogen mitigation system of 20 igniters and 6 PARs is installed to control the hydrogen in the containment during severe accidents and design basis accidents, respectively, in Shin-Wolsung 1 and 2 nuclear power plants. The igniters are primarily installed at the hydrogen source locations, and the PARs are installed in the open spaces. The PARs will maintain the hydrogen concentration within the containment atmosphere below the limit of 4 v/o in accordance with Regulatory Guide 1.7 during design basis accidents. The igniters will maintain the hydrogen concentration within the containment atmosphere below the limit of 10 v/o in accordance with 10CFR50.34(f) during severe accidents. In addition, the PARs can be used as a supplementary means to control the hydrogen concentration during severe accidents because of their ...
Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The ...
Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The ...
Detailed chemical kinetic reaction mechanisms are developed for combustion of all nine isomers of heptane (C{sub 7}H{sub 16}), and these mechanisms are tested by simulating autoignition of each isomer under rapid compression machine conditions. The reaction mechanisms focus on the manner in which the molecular structure of each isomer determines the rates and product distributions of possible classes of reactions. The reaction pathways emphasize the importance of alkylperoxy radical isomerizations and addition reactions of molecular oxygen to alkyl and hydroperoxyalkyl radicals. A new reaction group has been added to past models, in which hydroperoxyalkyl radicals that originated with abstraction of an H atom from a tertiary site in the parent heptane molecule are assigned new reaction sequences involving additional internal H atom abstractions not previously allowed. This process accelerates autoignition in fuels with ...
The project is intended to yield information on the transfer factors describing the transfer of ingested radionuclides to breast milk for the following elements: antimony, cerium, chromium, cobalt, gallium, lanthanum, molybdenum, niobium, radium, ruthenium, silver, thorium, titanium, and uranium. Those yet unknown or poorly known transfer factors are required in order to be able to develop a reliable model for description and assessment of the transfer of the radionuclides and the possibly resulting hazardous doses to infants, and for subsequent formulation of recommendations for radiological protection of the population. (orig./CB)
Technetium transfer from soil to edible parts of various agricultural plants is studied with application of the "9"5"mTc radioactive tracer. The samples of agricultural plants were grown on andesol typical for Japan soil. The technetium transfer factor to edible parts of cultivated lettuce was higher as compared to non foliate cultures. Relative low transfer factor were observed for fruit and pod like plants. the transfer factors for root crops were of intermediate value
Heat transfer augmentation by straight grid spacers in rod bundles is studied for single phase flow and for post critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single phase flow is also examined. Governing heat transfer mechanisms are analyzed, and predictive formulations are established. For single phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. 18 refs.
Several aspects of heat transfer at the annular two phase flow regime are considered. Nucleate boiling is supposed to be absent. Theoretical solutions for cases of laminar and turbulent flow in the liquid film, respectively, are considered, when steam presence does not effect the heat transfer. Heat transfer in annular flows is also considered, where steam phase consists totally or partially of the so-called incondensable gas. In this case steam phase can be a considerable resistance to heat transfer.
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
A series of hydrogenation/dehydrogenation cycles have been performed on palladium wire samples, stressed by a constant mechanical tension, in order to investigate the changes in electrical and mechanical properties. A large increase of palladium electrical resistivity has been reported due to the combined effects of the production of defects linked to hydrogen insertion into the host lattice and the stress applied to the sample. An increase of the palladium sample strain due to hydrogenation/dehydrogenation cycles in ????? phase transitions is observed compared to the sample subjected to mechanical tension only. The loss of initial metallurgical properties of the sample occurs already after the first hydrogen cycle, i.e. a displacement from the initial metallic behavior (increase of the resistivity and decrease of thermal coefficient of resistivity) to a worse one occurs already after the first ...
A process combining dark fermentation and photofermentation for production of hydrogen is interesting due to its potential of producing hydrogen at a high yields. In this study, the hydrogen process is compared to a 2nd generation ethanol process with respect to cost and with the aim of increasing our understanding of the pros and cons and giving a clear picture of the present status of the two processes. The hydrogen production cost was found to be about 20 times higher than the ethanol production cost, 421.7&z.euro;/GJ compared to 19.5&z.euro;/GJ. The main drawbacks of the hydrogen process are its low productivity, low energy efficiency, and the high cost of buffer and base required to control the pH.
This patent describes a method of reducing the hydrogen sulfide level in streams containing hydrogen sulfide at concentrations from about 2 ppm up to about 1,000 ppm. It comprises reacting the hydrogen sulfide with an unsaturated hydrocarbon in the presence of an acidic solid catalyst selected from the group consisting of polymeric sulfonic acid resins, solid polyphosphoric acid, supported sulfuric acid, supported boric acid, silica-aluminas, clays, faujasite, mordenite, and L, omega, X or Y zeolites at mercaptan-forming concentrations, and recovering a stream having a reduced hydrogen sulfide concentration and containing no more than 5 ppm hydrogen sulfide.
This paper investigates various usages of natural gas (NG) as an energy source for different hydrogen production technologies. A comparison is made between the different methods of hydrogen production, based on the total amount of natural gas needed to produce a specific quantity of hydrogen, carbon dioxide emissions per mole of hydrogen produced, water requirements per mole of hydrogen produced, and a cost sensitivity analysis that takes into account the fuel cost, carbon dioxide capture cost and a carbon tax. The methods examined are the copper-chlorine (Cu-Cl) thermochemical cycle, steam methane reforming (SMR) and a modified sulfur-iodine (S-I) thermochemical cycle. Also, an integrated Cu-Cl/SMR plant is examined to show the unique advantages of modifying existing SMR plants with new h...
A method for determining the mobility of hydrogen as a function of temperature in superconducting niobium cavities comprising: 1) heating a cavity under test to remove free hydrogen; 2) introducing hydrogen-3 gas into the cavity; 3) cooling the cavity to allow absorption of hydrogen-3; and 4) measuring the amount of hydrogen-3 by: a) cooling the cavity to about 4.degree. K while flowing a known and regulated amount of inert carrier gas such as argon or helium into the cavity; b) allowing the cavity to warm at a stable rate from 4.degree. K to room temperature as it leaves the chamber; and c) directing the exit gas to an ion chamber radiation detector.
Hydrogen has the potential to serve as both an energy storage means and an energy carrier in renewable energy systems. When renewable energy sources such as solar or wind power are used to produce electrical power, the output can vary depending on weather conditions. By using renewable sources to produce hydrogen, a fuel which can be stored and transported, a reliable and continuously available energy supply with a predictable long-term average output is created. Electrolysis is one method of converting renewable energy into hydrogen fuel. In this experiment we examine the use of an electrolyzer based on polymer-electrolyte membrane technology to separate water into hydrogen and oxygen. The oxygen is vented to the atmosphere and the hydrogen is stored in a small pressure vessel.
Discusses results of investigations into catalytic properties of various minerals during hydrogenation of Kansk-Achinsk brown coal with a view to replacing synthetic compositions based on molybdenum. Describes tests and equipment used in hydrogenation of grade B-2 Borodinsk deposit coal in tetralin (hydrogen donor). Various by-products of metallurgical processes and compounds separated from tailings containing mainly iron and sulfur and other metals were used as catalysts. States that: minerals containing iron compounds in the form of pyrites, hematites and magnetites exhibit catalytic properties when used in the hydrogenation of brown coal; pyritic catalysts enrich liquid products with hydrogen while sulfur and nitrogen content remains the same; the yield of malthenes with pyritic catalysts is no lower than with alumocobaltmolybdenum catalysts. 18 refs.
Although hydrogen is the simplest of atoms, it does not form the simplest of solids or liquids. Quantum effects in these phases are considerable (a consequence of the light proton mass) and they have a demonstrable and often puzzling influence on many physical properties, including spatial order. To date, the structure of dense hydrogen remains experimentally elusive. Recent studies of the melting curve of hydrogen indicate that at high (but experimentally accessible) pressures, compressed hydrogen will adopt a liquid state, even at low temperatures. In reaching this phase, hydrogen is also projected to pass through an insulator-to-metal transition. This raises the possibility of new state of matter: a near ground-state liquid metal, and its ordered states in the quantum domain. Ordered quantum fluids are traditionally categorized as superconductors or superfluids; these respective ...
OAK B188 The goal of this project is to mimic the energy transduction processes by which photosynthetic organisms harvest sunlight and convert it to forms of energy that are more easily used and stored. The results may lead to new technologies for solar energy harvesting based on the natural photosynthetic process. They may also enrich our understanding and control of photosynthesis in living organisms, and lead to methods for increasing natural biomass production, carbon dioxide removal, and oxygen generation. In our work to date, we have learned how to make synthetic antenna and reaction center molecules that absorb light and undergo photoinduced electron transfer to generate long-lived, energetic charge-separated states. We have assembled a prototype system in which artificial reaction centers are inserted into liposomes (artificial cell-like constructs), where they carry out light-driven transmembrane translocation of hydrogen ions to ...
The finite-volume based commercial CFD-code Fluent was used to simulate the reacting flow in a heavy fuel oil fired laboratory furnace. Both the standard {kappa}-{epsilon} turbulence model and the Reynolds stress model (RSM) were tested. The combustion model was based on the conserved scalar (mixture fraction) and prescribed probability density function approach. The heavy fuel oil droplet trajectories were predicted by solving the momentum equations for the droplets using the Lagrangian treatment. The soot distribution in the furnace was calculated by solving a transport equation for the soot mass fraction. Simple expressions for the soot formation and oxidation rates were employed. The radiation heat transfer equation was solved using the finite volume method. The formation of thermal NO from molecular nitrogen was modeled according to the extended Zeldovich mechanism. Fuel-based NO was modeled assuming that all the nitrogen in the fuel is released as ...
The Neutral Beam Test Facility (NBTF) to be realized in Padoa will test the Neutral Beam Injection (NBI), one of the Heating and Current Drive Systems foreseen for ITER. The NBI is based on the acceleration of hydrogen or deuterium negative ions up to 1 MeV. This work has been aimed at assessing the tritium release from the NBTF in order to provide data for the safety analysis. In particular, the diffusion of the tritium through the neutral beam target material (the CuCrZr alloy calorimeter panels) has been assessed by using literature data of the diffusion coefficient. The tritium generated inside the calorimeter panels moves into both the vacuum and water side: the tritium diffusion flux has been evaluated during the beam-on (200 deg. C) and the beam-off (20 deg. C) phases of the NBTF experiments consisting of an interim campaign and a final test. The penetration depth of the tritium through the 2 mm thick CuCrZr alloy material has been also evaluated by using a ...
The Neutral Beam Test Facility (NBTF) to be realized in Padoa will test the Neutral Beam Injection (NBI), one of the Heating and Current Drive Systems foreseen for ITER. The NBI is based on the acceleration of hydrogen or deuterium negative ions up to 1 MeV. This work has been aimed at assessing the tritium release from the NBTF in order to provide data for the safety analysis. In particular, the diffusion of the tritium through the neutral beam target material (the CuCrZr alloy calorimeter panels) has been assessed by using literature data of the diffusion coefficient. The tritium generated inside the calorimeter panels moves into both the vacuum and water side: the tritium diffusion flux has been evaluated during the beam-on (200 deg. C) and the beam-off (20 deg. C) phases of the NBTF experiments consisting of an interim campaign and a final test. The penetration depth of the tritium through the 2 mm thick CuCrZr alloy material has been also evaluated by using a ...
Six safety initiatives have been identified for accelerating the resolution of waste tank safety issues and closure of unreviewed safety questions. Safety Initiative 5 is to reduce safety and environmental risk from tank leaks. Item d of Safety Initiative 5 is to complete corrosion studies of single-shell tanks to determine failure mechanisms and corrosion control options to minimize further degradation by June 1994. This report has been prepared to fulfill Safety Initiative 5, Item d. The corrosion mechanisms that apply to Hanford Site single-shell tanks are stress corrosion cracking, pitting/crevice corrosion, uniform corrosion, hydrogen embrittlement, and microbiologically influenced corrosion. The corrosion data relevant to the single-shell tanks dates back three decades, when results were obtained from in-situ corrosion coupons in a few single-shell tanks. Since that time there have been intertank transfers, evaporation, and chemical ...
Full text: In heavy-water-moderated power reactors, tritium is primarily produced by neutron capture in deuterium nuclei in the moderator and coolant. For CANDU 6 reactors, the estimated steady-state values are #approx# 3 TBq#centre dot#kg"-"1 D_2O in the moderator and #approx# 74 GBq#centre dot#kg"-"1 D_2O in the coolant. Tritium removal is one option available to reactor operators for use in their heavy water and tritium management strategies. The WTRF is designed to remove tritium from tritiated heavy water in each of the four CANDU units at the Wolsung Site, to immobilize the tritium and to store it on site. The detritiation process is based on three steps: the first one (front-end) involves the transfer of tritium from heavy water to deuterium gas; the second one (enrichment) concentrates the tritium in a cryogenic distillation system to produce essentially pure D_2 and T_2 streams; and in the third step the tritium is packaged for long-term storage. The WTRF ...
A way to synthesize the transient zwitterionic silylene L'Si: 8 {L'=CH[(C=CH(2))CMe(N(tBu))(2)]} and achieve its facile dimerization to the remarkable N-heterobicyclic disilane 8(2) is described. At first, employing the beta-diketiminate ligand L [L=CH(CMeN(tBu))(2)], both starting materials LH (2) and its N-lithium salt LLi (3) can react with SiBr(4) to yield the silylene precursor L'SiBr(2) (4) by silicon-induced C-H activation at an exocyclic methyl group on the backbone of the ligand. Compound 4 reacts with SiBr(4) above room temperature to afford the unexpected terminal CH(SiBr(3))-substituted dibromosilane 6 along with the unique tricyclic trisilane 7. Reduction of 4 with KC(8) at 0 degrees C furnishes the novel N-heterobicyclic disilane 8(2), which is a formal dimer of the desired zwitterionic silylene L'Si: (8). It has been reasoned that compound 8(2) may results from [4+1] cycloaddition of two molecules of 8 to give the transient dimer 8(2)', which subsequently undergoes ...
The A2P-X2+Dv=-3 bands of the 12C14N radical have been observed by time-resolved Fourier transform spectroscopy in the 1850-3100cm-1 region with a wavenumber resolution of 0.025cm-1. The radical was produced in a pulsed positive column discharge in a cyanogene and helium mixture. Seven bands of v=0-3, 1-4, 2-5, 3-6, 4-7, 5-8, and 6-9 were analyzed to give the molecular constants of each state by least-squares fitting of 801 lines. The pulsed discharge was found to be efficient for production of CN in the excited A2P state. The vibrational excitation temperature was determined to be 6680+-835K and 6757+-534K for the A2P and X2+ states, respectively. The population of the A2P was found to be 4% of that of the X2+ state in the time after turning off the discharge.
The purpose was to study the toxicity of drugs known to generate free radicals on isolated pancreatic islets. The accumulattion of "8"6Rb"+ by mouse pancreatic islets was measured in vitro. Exposing the islets to 6-hydroxydopamine, minhydrin, or phenazine methosulphate + NADH inhibited the Rb"+ uptake, whereas paraquat or acetylphenylhydrazine had no effect. This effect of 6-hydroxydopamine was prevented by either of the hydroxyl radical scavengers, sodium benzoate and mannitol, but not by the non-scavenger,urea; ninhydrin was partially protected against by mannitol but not by benzoate. Protection against 6-hydroxydopamine was also afforded by D-glucose but not by L-glucose or 3-O-methyl-D-glucose; none of the sugars protected against ninhydrin. In damaging islet beta-cells and in being protected against by D-glucose, 6-hydroxydopamine closely resembles the diabetogenic drug, alloxan. It is suggested that protection against alloxan may involve ...
A novel technique is proposed for the growth of an InN film on a GaN/Al2O3(0001) template by radio-frequency plasma-excited molecular beam epitaxy (RF-MBE). The method involves 1) InN growth under an In-rich condition and 2) additional nitrogen radical irradiation after the InN growth under an In-rich condition. Excess In that appeared on the InN surface in the InN growth under an In-rich condition is transformed to InN by the additional nitrogen radical irradiation. The effective V/III ratio is easily controlled by monitoring the intensity in a reflection high-energy electron diffraction (RHEED) pattern. The growth of the InN film by repeating the InN growth under an In-rich condition and the additional nitrogen radical irradiation is also demonstrated. (copyright 2009 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)
Lysozyme dimers produced on oxidation of lysozyme with Br_2anion radicals in aqueous solutions exhibit a fluorescence spectrum (lambdasub(max) = 400 nm) closely similar to that of bi-tyrosine. This suggests that the dimer is likely to have a tyrosine-tyrosine bond resulting from the combination of tyrosine phenoxy radicals of two lysozyme molecules. Kinetic studies on dimer formation were made by measuring time-dependent fluorescence after pulsed-electron irradiation over wide pH range. The results lead to the following conclusions. The second-order growth of the dimer fluorescence observed at pH 10.7-12.5 reflects the combination process of the lysozyme radicals, which is rate-determining in the pH range. On the other hand, the first-order growth observed at pH 6.8-10.2 is attributable to the enolization of the keto-form of the dimer. A tentative reaction scheme is proposed for the dimer formation. (author).
The present study was undertaken in 27 children with localized Ewing's sarcoma treated at our hospital. In 9 cases the lesion was central and in 18 peripheral. Treatment consisted of: 1) Chemotherapy with 6 drugs (vincristine, cyclophosphamide, methotrexate, bleomycin, dactinomycin and doxorubicin) for one year in all patients; 2) Radiotherapy in 24 patients at a dose of 30-40 Gy in the entire bone with a booster dose of 10-15 Gy in the lesion. In 7 patients debulking surgery was performed followed by irradiation. Two cases with tumor in expendable bones and one with extensive destructive lesion in the tibia underwent radical surgery. One patient suffered local recurrence (femur) and 6 developed distant metastases. The remaining 20 (74%) patients were alive and tumor-free after follow-up periods of 17-80 months. Among the 12 patients with extremity lesions who were alive, 7 (58%) had minimal or mild treatment sequelae, 2 moderate, and 3 severe sequelae but no ...
To elucidate the mechanism of sunlight-induced skin damage, guinea pigs exposed to UV light (280-320 nm, UV B, 4J/cm"2) and a homogenate of the epidermis was examined by means of the thiobarbituric acid (TBA) test. Three hours after the exposure, TBA-malondialdehyde adducts had increased while glutathione reductase activity had decreased, indicating lipid peroxidation. To detect the initial species, spin trapping with 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) was applied to a suspension of illuminated epidermal cells (0.5 J/cm"2). An ESR signal obtained only with irradiation comprised a 1 : 2 : 2 : 1 quartet [a (N) =a (#beta#H) =1.49 mT] attributable to a spin adduct of hydroxyl radicals. These results suggest that sunlight exposure of skin may lead to hydroxyl radical generation and simultaneous lipid peroxidation. (author).
Bacteriophage M13 mp10 DNA were irradiated with near-UV light in the presence of tetracycline derivatives and primed with synthetic oligonucleotide to be used for DNA synthesis using Escherichia coli DNA polymerase. Chain terminations were observed by denaturing polyacrylamide gel electrophoresis and mapped precisely. All the synthesis stops occurred before or at the level of guanine residues, showing that the photoreaction mediated by tetracycline derivatives led to a preferential alteration of guanine residues. These lesions were demonstrated to be induced in DNA through a pathway involving singlet oxygen. Tetracycline derivatives also photoinduced the breakage of the DNA sugar-phosphate backbone monitored by the conversion of supercoiled phi X174 DNA to a relaxed form. This lesion was shown to be initiated by hydroxyl radicals. The production of this free radical has been confirmed by electron paramagnetic resonance (EPR) spin trapping ...
Two measurement methods to determine the rate of neutral free radical production by the photo-deionization of negative ion beams (PDINIB) are introduced. These methods, namely, photoelectron-current measurement by low-frequency electro-modulation probe (PMMP) and measurement of decrease in the negative-ion beam current (DNIC) were employed to evaluate the production rate in a trial surface-processing apparatus developed in the author's laboratory utilizing a steady-flux refined beam of neutral free radicals (RBNR) produced by the PDINIB procedure. A {sup 63}Cu{sup -} negative ion beam of kinetic energy E{sub i} varied up to 15 keV was irradiated with a 514.5 nm visible light beam from a 25 W CW Ar{sup +} ion laser. The detection limit of the production rate by the PMMP setup was as high as 6 x 10{sup 9} s{sup -1} under the condition that E{sub i}=15 keV, the negative-ion beam current I{sub i}=4 {mu}A and the laser power P=6 W. The DNIC ...
We summarize the predictions of different models for total #gamma##gamma# cross-sections. The experimentally observed rise of #sigma#_#gamma#_#gamma# with s radical _#gamma#_#gamma#, faster than that for #sigma#_p_-_b_a_r_p, #sigma#_#gamma#_p is in agreement with the predictions of the Eikonalized Minijet Models as opposed to those of the Regge-Pomeron models. We then show that a measurement of #sigma#_#gamma#_#gamma# with an accuracy of < or approx. 8-9% (6-7%) is necessary to distinguish among different Regge-Pomeron type models (the different parameterisations of the EMM models) and a precision of < or approx. 20% is required to distinguish the predictions of the EMMs and of those models which treat 'photon like a proton', for the energy range 300< s radical_#gamma#_#gamma# <500 GeV. We further show that the difference in model predictions for #sigma#_#gamma#_#gamma# of about a factor 2 at s radical ...
Charge-charge interactions dramatically influence the dissociation and proton transfer reactivity of large multiply protonated ions. In combination with tandem mass spectrometry, proton transfer...Full Text Available
Coupled rat heart mitochondria produce externally hydrogen peroxide at the rates which correspond to about 0.8 and 0.3 per cent of the total oxygen consumption at State 4 with succinate and...Full Text Available
Power output of a hydrogen-diesel dual-fuel engine is limited by the onset of knock as the percentage of heat input derived from hydrogen increased beyond a certain limit. Earlier work carried out at the Internal Combustion Engines Laboratory, Indian Institute of Technology, Madras, indicates that this knock sets in when the induced hydrogen exceeds about 60% of input energy at a pilot diesel quantity of 30% of full load diesel amount. At higher rates of hydrogen induction, the richer hydrogen-air mixture is more prone to knocking. Hardly any information is available on the possibilities of improving the knock limited power output of a hydrogen-diesel dual-fuel engine. Water can serve as a powerful internal coolant in decreasing the unburned mixture temperature because of its high latent heat. This paper presents the results of our investigation on improving the ...
The feasibility of utilizing photoelectrochemical and electrolytical technologies to convert energy from the sun and wind into hydrogen was studied. In exploring opportunities to reduce the cost of hydrogen production through interaction with the electric utility grid, it was found that direct photoelectrochemical (PEC) conversion of sunlight has the economic potential to compete with direct photovoltaic/electrolysis, notwithstanding the significant stability and efficiency issues that are still awaiting solution. Interaction with the grid, while maximizing electrolizer use, makes a significant impact on the economics of producing hydrogen by photovoltaic/electrolysis, making wind-based systems also more economical. Electrolysis was found to be the optimal solution only with electricity from renewable sources or with less expensive non-peak electricity. On the other hand, the delivered cost of hydrogen ...
In order to replace industrial cobalt and nickel and molybdenum catalysts, more economical catalysts, red muds, are used. Comparative data about the chemical, structural and thermal properties of different samples of red muds, which are important for catalytic hydrogenation, are cited. The different conditions for hydrogenation of coals in a reactor are examined.
Combining in situ Rutherford backscattering and electrical transport measurements on low-temperature hydrogen-implanted amorphous Pd/sub 80/Si/sub 20/ films, we have studied the correlation between the hydrogen content and the resistivity.
Platinized cadmium sulfide powder suspended in a solution of sodium sulfite produces hydrogen efficiently by visible light. Sulfite ions are oxidized to sulfate and dithionate ions. 4 figures.
Current hydrocarbon-based energy systems, current energy consumption and the push towards the utilization of renewable energy sources, fuelled by global warming and the need to reduce atmospheric pollution are discussed. The consequences of climatic change and the obligation of Annex B countries to reduce their greenhouse gas emissions in terms of the Kyoto Protocols are reviewed. The role that renewable energy sources such as hydrogen, solar and wind energy could play in avoiding the most catastrophic consequences of rapidly growing energy consumption and atmospheric pollution in the face of diminishing conventional fossil fuel resources are examined. The focus is on hydrogen energy as a means of storing and transporting primary energy. Some favorable characteristics of hydrogen is its abundance, the fact that it can be produced utilizing renewable or non-renewable sources, and the further fact that its combustion produces ...
car running down the track." Choosing to focus on the design of a hydrogen fuel cell model car rather than a solar race car was a deliberate decision for team, "Larry the...
An important application of metal hydrides is as a moderator material in nuclear reactors. The fundamental properties of hydrides are illustrated and an impression given of the current research into hydrogen in transition metals. Phase diagrams, magnetic properties, temperature dependence of the diffusion coefficient, energy level schemes and superconductivity are considered. (C.F.).
Alternative energy resources such as hydrogen and methane gases are becoming increasingly important for the future economy. A major challenge for using hydrogen is to develop suitable materials to store...Full Text Available
The various steps of gas treatment in the Sasol II coal liquefaction plant are discussed: CO/sub 2/ removal, separation of the hydrocarbon fractions and the recirculated hydrogen by low-temperature decomposition, production of pure hydrogen by alternating pressure absorption.
Cost is a key issue in the spreading of any technology. In this work, the cost of hydrogen is analyzed and determined, for hydrogen obtained by electrolysis. Different contributing partial costs are taken into account to calculate the hydrogen final cost, such as energy and electrolyzers taxes. Energy cost data is taken from official URLs, while electrolyzer costs are obtained from commercial companies. The analysis is accomplished under different hypothesis, and for different countries: Germany, France, Austria, Switzerland, Spain and the Canadian region of Ontario. Finally, the obtained costs are compared to those of the most used fossil fuels, both in the automotive industry (gasoline and diesel) and in the residential sector (butane, coal, town gas and wood), and the possibilities of hydrogen competing against fuels are discussed. According to this work, in the automotive industry, even neglecting ...
The effects of ammonia and hydrogen sulfide on the physical and biochemical properties of the claw horn of Holstein cows were evaluated. Significant (P < 0.05, 0.01) decreases...Full Text Available
It is well known that the solubilization of coal can be accelerated by adding sulfur or hydrogen sulfide during direct liquefaction of difficult coals. From the studies of authors on the coal liquefaction under the conditions at rather low temperatures between 300 and 400{degree}C, liquefaction products with high quality can be obtained by suppressing the aromatization of naphthene rings, but it was a problem that the reaction rate is slow. For improving this point, results obtained by changing solvents have been reported. In this study, to accelerate the liquefaction reaction, Illinois No.6 coal was liquefied in tetralin at temperature range from 300 to 400{degree}C by adding a given amount of sulfur or hydrogen sulfide at the initial stage of liquefaction. The addition of sulfur or hydrogen sulfide provided an acceleration effect of liquefaction reaction at temperature range between 300 and 400{degree}C. The addition of ...
A new process for the hydrogenation of coal in the presence of wide-cut coal tar was proposed; it involves cavitation treatment, mixing with catalytic additives, and heating the resulting mixture at an elevated pressure in an atmosphere of hydrogen. The yields of hydrocarbon fractions to 300?C and gas condensate were evaluated.
Under anaerobic conditions, several species of green algae perform a light-dependent hydrogen production catalyzed by a special group of [FeFe] hydrogenases termed HydA. Although highly interesting...Full Text Available
In this paper we have proposed a novel gas turbine cycle with hydrogen-fueled chemical-looping combustion, and the system study on two hydrogen-fueled power plants, the new gas turbine cycle and an advanced gas turbine cycle with H{sub 2}/O{sub 2} combustion, has been investigated with the aid of exergy principle (EUD methodology). The hydrogen fueled chemical-looping combustion in the new gas turbine cycle consists of two successive reactions: hydrogen fuel is reacted with metal oxide (reduction of metal oxide), and then instead of air or pure oxygen, the reduced metal is successively oxidized by the saturated air. As a result, the new hydrogen-fueled gas turbine cycle has a breakthrough performance, with at least about 12 percentage-point higher efficiency compared to the gas turbine cycle with H{sub 2}/O{sub 2} combustion, and will be environmentally superior due to complete ...
A solvent extraction method was developed to obtain methanolic extracts rich in antioxidants from banana peel. Central composite design ''2^3+star'' and response surface methodology were used in order to optimise the number of extraction steps, extraction temperature and extraction time. The number of extractions was statistically the most significant factor in scavenging activity against both DPPH? and ABTS?^+ radicals and in the inhibition of TBARS formation, while the extraction temperature had an important impact on the capacity to prevent b-carotene bleaching. However, the effect of the extraction time on antioxidant activity was less important. The optimum values of the factors that influence the capacity to scavenge DPPH? and ABTS?^+ radicals or to inhibit b-carotene bleaching were ...
The authors search Z{prime} bosons in dielectron events produced in p{bar p} collisions at {radical}s = 1.96 TeV, using a 0.45 fb{sup -1} dataset accumulated with the CDF II detector at the Fermilab Tevatron. To identify the Z{prime} {yields} e{sup +}e{sup -} signal, both the dielectron invariant mass distribution and the angular distribution of the electron pair are used. No evidence of a signal is found, and 95% confidence level lower limits are set on the Z{prime} mass for several models. Limits are also placed on the mass and gauge coupling of a generic Z{prime}, as well as on the contact interaction mass scales for different helicity structure scenarios.
The incidence of hilar cholangiocarcinoma is very rare worldwide. Radical resection is the only prognostic factor for long survival in patients with hilar cholangiocarcinoma. Postoperative radiation therapy can improve local control and survival rates for patients with palliative resection, but it remains controversial in patients with radical resection. Biliary drainage can effectively release bile duct obstruction for the majority of patients with locally advanced disease, and may even prolong survival when combined with radiation therapy. Radiation therapy includes extrernal beam therapy alone, external beam therapy with intraluminal brachytheapy and new radiation technique, such as three dimentional conformal therapy and intensity modulated radiation therapy. The propective randomized clinical study is needed for further investigation in the role of combined modality therapy especially for hilar cholangiocarcinoma. (authors)
Purpose. To compare erectile function (EF) recovery of patients treated by early penile rehabilitation therapy (PRT) with sildenafil and with control group. Method. Forty men treated by bilateral nerve sparing radical prostatectomy (NSRP) and with a normal pre-operative EF were enrolled. Fourteen days after surgery, they were randomised to a flexible-dose sildenafil group and to a control group. The International Index of Erectile Function (IIEF) questionnaire was completed before surgery and at 3, 6, 12 and 24 weeks after NSRP. Results. In the group treated, the mean IIEF score before surgery was 26.2 and 14.1, 16.2, 22.5 and 25.2 at 3, 6, 12 and 24 weeks after NSRP, respectively. In the control group, the respective scores were 26.5 and 12.4, 15.8, 15.3 and 17.4. There was a significant ...
ABSTRACT Introduction. Postprostatectomy erectile dysfunction (ED) remains a serious quality-of-life issue. Recent advances in the understanding of the mechanism of postprostatectomy ED have stimulated great attention toward penile rehabilitation. Aim. This review presents and analyzes a contemporary series of the recent medical literature pertaining to penile rehabilitation therapy after radical prostatectomy (RP). Main Outcome Measures. The laboratory and clinical studies related to penile rehabilitation are analyzed. The validity of the methodology and the conclusion of the findings from each study are determined. Methods. The published and presented reports dealing with penile rehabilitation following RP in human and cavernous nerve injury in animal models are reviewed. Results. Exciti...
The optimal management of men with very favorable clinicopathological factors who develop biochemical recurrence (BCR) after radical prostatectomy (RP) has not been previously reported. Both local and systemic recurrences are unlikely in this cohort. This study examines their management and outcomes. Between October 2000 to March 2010, 1627 men underwent open RP by a single surgeon. In all, 448 (27.5%) met the following criteria for extremely low risk disease: preoperative PSA level <10?ng?ml?1, clinical stage T1c/T2a, Gleason score ?6, estimated cancer volume in the surgical specimen ?5% and no evidence for positive surgical margin. Undetectable PSA was defined as ?0.04?ng?ml?1. BCR was defined as PSA ?0.2?ng?ml...
The radiation induced reactions in LDPE in the presence of phenolic type antioxidants have been studied. It was shown that various antioxidants can influence the polyethylene network formation and the radical yield in different ways. The dependence of network structure on absorbed doses was determined by gel analysis, hot-set test and extraction of antioxidants for samples irradiated with accelerated electrons. It was found that the antioxidants eluted from polyethylene in higher percentage influence polymer crosslinking to a smaller degree. The ESR studies of #gamma#-irradiated blends of polyethylene with antioxidant indicate the presence of alkyl and phenoxyl radicals. The role of antioxidant molecules on radiation induced reactions in polyethylene-antioxidant systems is considered. The correlation between the network structure and the type of additive in polyethylene is also discussed. (author).
Three alternative extraction procedures were carried out in order to separate the antioxidant components and isolate an efficient extract from Origanum dictamnus. Procedure A included sequential extractions with petroleum ether (PE), diethyl ether (DE) and ethanol; procedure B sequential extractions with PE and ethyl acetate (EAc); procedure C a single step extraction with ethanol. The most efficient radical scavengers, according to the DPPH method, were isolated in ethanol extract of procedure A (mainly rosmarinic acid), followed by ethanol extract of procedure C. However, both ethanol extracts had low solubility in oil and could not protect it. EAc and DE extracts, containing mainly apigenin and epirosmanol ethyl ether, presented lower radical scavenging activity but were very effective ...
Evidence is reported for a narrow structure near the J/{psi}{phi} threshold in exclusive B{sup +} {yields} J/{psi}{phi}K{sup +} decays produced in {bar p}p collisions at {radical}s = 1.96 TeV. A signal of 14 {+-} 5 events, with statistical significance in excess of 3.8 standard deviations, is observed in a data sample corresponding to an integrated luminosity of 2.7 fb{sup -1}, collected by the CDF II detector. The mass and natural width of the structure are measured to be 4143.0 {+-} 2.9(stat) {+-} 1.2(syst) MeV/c{sup 2} and 11.7{sub -5.0}{sup +8.3}(stat) {+-} 3.7(syst) MeV/c{sup 2}.
Abstract Purpose: We evaluated complications of urologic laparoscopic surgery at our institution. Patients and Methods: From December 1991 to January 2009, 1017 urologic laparoscopic surgical procedures were performed in Kansai Medical University, including 277 radical prostatectomies, 13 donor nephrectomies, 74 partial nephrectomies, 158 radical nephrectomies, 55 pyeloplasties, 97 nephrouretectomies, 54 simple nephrectomies, 128 adrenalectomies, 34 varicocelectomies, and 127 other procedures. Medical records of each procedure were retrospectively evaluated. The difficulty of each procedure was classified according to the European Scoring System (ESS). Intraoperative and postoperative complications were graded according to the Satava and Clavien classifications, respectively. Results: Amon...
Banana (Musa acuminata Colla AAA) peel extracts obtained in this work had a high capacity to scavenge 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2prime-azino-bis(3-ethylbenzothiazoline)-6-sulfonic acid (ABTS+) free radicals, and they were also good lipid peroxidation inhibitors. Acetone:water extracts were considerably more effective (compared with methanol, ethanol, acetone, water, methanol:water or ethanol:water) at inhibiting the peroxidation of lipids in the b-carotene/linoleic acid system or scavenging free radicals. However, aqueous extracts had a high capacity to protect lipids from oxidation in the thiobarbituric acid reactive substances (TBARS) test, as well as in the b-carotene bleaching assay. In addition, acetone:water most efficiently extracted all extractable components (54+-...
I describe a search for anomalous production of Z pairs through a new massive resonance X in 2.5-2.9 fb{sup -1} of p{bar p} collisions at {radical}s = 1.96 TeV using the CDFII Detector at the Fermilab Tevatron. I reconstruct Z pairs through their decays to electrons, muons, and quarks. To achieve perhaps the most efficient lepton reconstruction ever used at CDF, I apply a thorough understanding of the detector and new reconstruction software heavily revised for this purpose. In particular, I have designed and employ new general-purpose algorithms for tracking at large {eta} in order to increase muon acceptance. Upon analyzing the unblinded signal samples, I observe no X {yields} ZZ candidates and set upper limits on the production cross section using a Kaluza-Klein graviton-like acceptance.
It has been discovered that when Taiheiyo coal pulverized to 200 mesh or smaller is dispersed in naphthalene, a non-hydrogen-donor solvent, and reacted under hydrogen pressure in the presence of a red mud/sulfur catalyst, the catalyst exhibits activity in the regeneration of hydrogen donor solvents which have been hydrogen-depleted in the course of coal liquefaction. It is already known that inorganic matter contained in coal acts as a catalyst in liquefaction. This suggests that the reported effect of the red mud/sulfur catalyst is due to the iron oxide reacting with the sulfur and forming pyrrhotite. 22 refs., 6 figs., 1 tab.
A prototype hydride storage bed, using LaNi{sub 4.25}Al{sub 0.75} as the storage material, was fitted with strain gages to measure strains occurring in the stainless steel bed vessel caused by expansion of the storage powder upon uptake of hydrogen. The strain remained low in the bed as hydrogen was added, up to a bed loading of about 0.5 hydrogen to metal atom ratio (H/M). The strain then increased with increasing hydrogen loading ({approximately} 0.8 H/M). Different locations exhibited greatly different levels of maximum strain. In no case was the design stress of the vessel exceeded.
The method of programmed thermodesorption has been used to study the forms of hydrogen adsorption in ZrNiHsub(x) hydride. It is shown that high concentration of the hydrogen, which extracted from hydride in the temperature range of 240-260 deg C results in appearance of ''reverse'' peak. Charge of hydride adsorption properties during its oxidation-reduction treatment is studied. Comparison with spectra of hydrogen thermodesorption from the surface of Ni/ZrO_2 deposited catalyst and zirconium oxide is carried out.
Iron alloys and aluminum were nitrogen implanted in a controlled oxygen atmosphere and the role of hydrogen on the surface etching mechanisms studied. The surface composition was analyzed by in situ photoemission electron spectroscopy (XPS). In iron alloys, hydrogen strongly etches oxygen, improving nitrogen retention on the surface. On the other hand, hydrogen removes nitrogen from aluminum surfaces, with a deleterious effect on the nitriding effectiveness. The oxygen removal in iron alloys is associated with the catalytic effect of electrons in d-orbitals and the nitrogen removal in aluminum is associated with a steric effect.
The temperature and pressure dependence of the mobilities of negative charges injected into liquid hydrogen and deuterium have been measured. The authors propose the existence of two types of charge carriers in liquid parahydrogen. One is a bubble with an electron inside while the other has higher mobility. Relaxation of the current through liquid hydrogen was observed. It is suggested that in liquid and solid hydrogen under {beta}-irradiation neutral complexes are created which can trap the negative charges and have a lifetime of about 10 hours. 6 refs., 5 figs.
disciplinary methods were used to independently determine the aerodynamic loads, the thermal response, and strardural performance of the hydrogen cooled ...
This bulletin traces development of high-pressure, coal and tar hydrogenation technology, based on an intensive review of pertinent literature. The bulletin written as part of the Bureau of Mines research program on synthetic liquid fuels covers the history and economics of the process; chemical aspects of hydrogenation of coal, tar, and middle oil; engineering aspects of converting coal and tar to liquid fuels, principally gasoline; and equipment for the process. The literature covered includes documents of United States and British governments, journals, and other publications. Bureau results in the hydrogenation field are also incorporated.
There are many reports concerning the behavior of hydrogen at coal liquefaction. However, all of them are the results by autoclave batch tests, and there are few reports discussing results of continuous coal liquefaction tests in long term operation. Coal liquefaction tests were conducted on Wandoan, Illinois No. 6, Wyoming and Tanito Harum coal at the NEDOL Process 1t/d Process Supporting Unit (PSU), and the behavior of hydrogen and deheterogeneity at coal liquefaction were investigated. Furthermore, the effect of fa (fraction of aromatic) of recycle solvent on the behavior of hydrogen was also studied.
... mass of gray gas by thermal radiation; An experimental study of the turbulent wake behind a cone at M = 5; Heat transfer augmentation by steady ...
heat transfer augmentation was found to increase with decreasing length scale but no optimum length scale was found. Heat transfer augmentation due to turbu- ...
Described herein is a system for the co-generation of hydrogen gas and electricity, wherein the proportion of hydrogen to electricity can be adjusted from 0% to 100%. The system integrates fuel cell technology for power generation with fuel-assisted steam-electrolysis. A hydrocarbon fuel, a reformed hydrocarbon fuel, or a partially reformed hydrocarbon fuel can be fed into the system.
Structural units of a hydrogen fuel cell whose characteristics are advisable to investigate by different neutron scattering methods are discussed. The results obtained with the use of Bragg diffraction and small-angle neutron scattering from fuel membranes, nanocarbon-platinum catalysts, and Zn_1_-_xCu_xO hydrogen storage systems are presented.
The investigations of lignite hydroliquefaction were aimed at improving reaction control in order to minimize residue and gas portion and hence increase the oil yield. To reach this goal, the process parameters were optimized and various catalysts tested for use in sump phase hydrogenation. Detailed investigations were also carried out on the problem of calcium carbonate agglomeration and the maceral decomposition behaviour of different lignite samples under hydrogenation conditions.
We combine a limited number of accurately measured transition frequencies in hydrogen and deuterium, recent quantum electrodynamics (QED) calculations, and, as an essential additional ingredient, a generalized least-squares analysis, to obtain precise and optimal predictions for hydrogen and deuterium transition frequencies. Some of the predicted transition frequencies have relative uncertainties more than an order of magnitude smaller than that of the g-factor of the electron, which was previously the most accurate prediction of QED.
We report the oxygen, hydrogen, and deuterium effects on nitrogen implantation of stainless steel. Oxygen is absorbed on the surface creating a potential barrier and diminishing the nitrogen retention. Deuterium removes more oxygen from the surface than hydrogen, augmenting the nitrogen chemical potential and yielding faster nitrogen diffusion into the bulk material.
HyPac is a french platform on the hydrogen and fuel cells applications, created in 2008. the authors presents the opportunities of the french platform HyPac, the objectives, the participants and the budget. (A.L.B.)
This fact sheet describes NREL's accomplishments in accurately modeling costs for fuel cell-based combined heat, hydrogen, and power systems. Work was performed by NREL's Hydrogen Technologies and Systems Center.
The isomeric composition of bicyclo(3.3.1)nonadienes was investigated by GLC and PMR spectroscopy with silver-lanthanide shift reagents. The absence of stereospecificity in the hydrogenation of 3,7-dimethylenebicyclo(3.3.1)nonane by hydrogen adsorbed on Raney nickel was demonstrated. This is explained by the sequence of the isomerization and then hydrogenation processes.
A method for the hydroconversion of coal by solvent treatment at elevated temperatures and pressure wherein an alcohol having an alpha -hydrogen atom, particularly a secondary alcohol such as isopropanol, is utilized as a hydrogen donor solvent. In a particular embodiment, a base capable of providing a catalytically effective amount of the corresponding alcoholate anion under the solvent treatment conditions is added to catalyze the alcohol-coal reaction.
Proton and neutron transfer populating low-lying states have been studied in the system {sup 144}Sm+{sup 88}Sr at an energy below the Coulomb barrier. The experimental cross sections for the single proton transfer are well reproduced by DWBA-calculations using spectroscopic information from light ion reactions. The two-proton transfer appears enhanced relative to the uncorrelated sequential transfer of single protons. The same holds for the transfer of proton pairs, the enhancement is kept for the second pair. This is interpreted as a supercurrent between two superfluid nuclear proton-pair wave functions: More mass and charge is transported per time unit in pairs than by single nucleons. Neutron transfer is observed with large cross sections and is found to contribute to the energy loss observed in the transfer reactions. For mixed ...
Proton and neutron transfer populating low-lying states have been studied in the system "1"4"4Sm+"8"8Sr at an energy below the Coulomb barrier. The experimental cross sections for the single proton transfer are well reproduced by DWBA-calculations using spectroscopic information from light ion reactions. The two-proton transfer appears enhanced relative to the uncorrelated sequential transfer of single protons. The same holds for the transfer of proton pairs, the enhancement is kept for the second pair. This is interpreted as a supercurrent between two superfluid nuclear proton-pair wave functions: More mass and charge is transported per time unit in pairs than by single nucleons. Neutron transfer is observed with large cross sections and is found to contribute to the energy loss observed in the transfer reactions. For mixed proton-neutron ...
A method of augmenting heat transfer in the interior of a fluid or from the interface of a solid in contact to a fluid by utilizing electro hydrodynamic (EHD) phenomena has the following advantages: the heat transfer can be effected by using a relatively small, light-weight high voltage source and some simple structural members; no vibration and noise are generated; the method has a control function to control heat transfer by adjustment of field and voltage; and this method is effective in cost-saving. It is mass transfer by the electric force caused by interaction between true charges or polarized charges in a fluid and external electric filed that plays an important role in most of such heat transfer augmentation methods by EHD. Examples of heat transfer augmentation by EHD phenomena include electricaly induced convection, contribution of EHD effect to heat ...
Looking at some of the national and international developments in hydrogen technology it becomes clear which important contributions the hydrogen technology oriented activities of the EU have helped to prepare and trigger: (a) Transport Energy Strategy (TES): This initiative of 7 major German automobile and mineral oilcompanies is aimed at an industrial consensus on one or two gasoline alternative fuels, which are to be presented to the German Ministry of Transport. An intermediate trend is that hydrogen may become the fuel of choice. (b) BMW: The Bayerischen Motorenwerke have already very early exposed themselves to the vehicle and component development of hydrogen as a vehicle fuel, focussing on a strategy from CNG to LNG and LH{sub 2}. (c) Opel and GM: Opel has recently announced they have chosen hydrogen as the primary long term fuel for their fuel cell vehicles to be ...
Role of microelements in coal in connection with their combustion in power stations, gasification and hydrogenation is discussed from the standpoint of environmental pollution and effects on technological parameters. In the wastes from fossil-fuel power stations there are biogenic and toxic elements (Be, B, Pb, etc.) present, which eventually go into the soil. Analyses showed that coal from the Kuznetsk, Donetsk, Ehkibastuz and Kansk-Achinsk basins which are used for power, have a relatively low level of biogenic and toxic microelements, e.g. Ba, B, Mn, Pb, Co, Ni, V, Cu, Y. Coal reactivity in gasification and hydrogenation is discussed. The catalytic effect of several microelements in coal gasification and hydrogenation is established. A geochemical multiplicative indicator is presented which makes quantitative evaluation of the suitability of coals for hydrogenation possible. 17 references.
This paper describes how hydrogen transport affects the severity of hydrogen embrittlement in 300 M and AerMet100 ultra high strength steels. Slow strain rate tests were carried out on specimens coated with electrodeposited cadmium and aluminium-based SermeTel 1140/962. Hydrogen diffusivities were measured using two-cell permeation and galvanostatic charging methods and values of 8.0 x 10{sup -8} and 1.0 x 10{sup -9} cm{sup 2} s{sup -1} were obtained for 300 M and AerMet100, respectively. A two-dimensional diffusion model was used to predict the hydrogen distributions in the SSR specimens at the time of failure. The superior embrittlement resistance of AerMet100 was attributed to reverted austenite forming around martensite laths during tempering.
Hydrogen seems to possess all the characteristics to store the excess of electrical energy produced during off-peak periods. Hydrogen energy storage plants could be environmentally non-polluting, easy to place, not sensible to load variation, unbounded in size, efficient and safe. These last two features seem to contradict one another. An option that could give a reliable solution is the storage of hydrogen in metal hydride and the storage of oxygen as a liquid. Such a choice is probably the safest one to make and allows the achievement of efficiencies comparable to those obtainable with gaseous storage of both electrolytic products. The power consumption for H{sub 2} and O{sub 2} storage is only 3% of the total energy stored and the charging ratio approaches the values obtained with hydro-pumped storage plants. (Author)
A study is made into textures of deformation and primary recrystallization forming in a #beta#-titanium alloy doped with hydrogen in amounts from 0.04 to 0.55 mass. %, on cold rolling with a 70%-reduction and dehydrogenating annealing at 860 deg C. It is shown that a volume fraction of recrystallization texture components is determined by the nature of corresponding deformation texture, in its turn, depending on hydrogen concentration in the alloy. At low hydrogen contents the main texture components are #left brace#111#right brace# and #left brace#001#right brace#. A hydrogen content increase up to 0.09 - 0.18 mass. % results in formation of dominant components of #left brace#111#right brace# and #left brace#112#right brace#
Any molecule which has a hydrogen atom attached directly to oxygen or nitrogen is capable of hydrogen bonding. The molecular complexes formed by hydrogen have particularly attracted considerable attention to understand the nature of the bond. The hydrogen bonded complexes formed by acetonitrile with certain alcohols such as tertiary butyl alcohol, isoamyl alcohol, cyclohexyl alcohol, hexyl alcohol and diethylene glycol in benzene were studied. The dipole moments of 1:1 complexes of the above said systems were determined at 308K. The dipolar increments for these systems were computed from the bond angle data available from molecular orbital studies. All these studied systems show that polarization interaction dominates in all the complexes.
Abstract Hydrogen bonding interactions between amino acids and nucleic acid bases constitute the most important interactions responsible for the specificity of protein binding. In this study, complexes formed by hydrogen bonding interactions between cysteine and thymine have been studied by density functional theory. The relevant geometries, energies, and IR characteristics of hydrogen bonds (H-bonds) have been systematically investigated. The quantum theory of atoms in molecule and natural bond orbital analysis have also been applied to understand the nature of the hydrogen bonding interactions in complexes. More than 10 kinds of H-bonds including intra- and intermolecular H-bonds have been found in complexes. Most of intermolecular H-bonds involve O (or N) atom as H-acceptor, whereas the...
Hydrogen molecule adsorption on the (0001) surface of double hexagonal closed packed americium has been studied in detail within the framework of density functional theory. Weak molecular hydrogen adsorptions were observed. The most stable configuration corresponded to a Hor2 approach molecular adsorption at the one-fold top site where the molecule's approach is perpendicular to a lattice vector. Adsorption energies and adsorption geometries for different adsorption sites will be discussed. The change in work functions, magnetic moments, partial charges inside muffin-tins, difference charge density distributions and density of states for the bare Am slab and the Am slab after adsorption of the hydrogen molecule will be discussed. Reaction barrier for the dissociation of hydrogen molecule will be presented. The implications of adsorption on Am 5f electron localization-delocalization will be summarized.
Austenitic stainless steel AISI 304 has been nitrided by radio frequency (rf) plasma containing various nitrogen-hydrogen gas mixtures, in order to study the effect of hydrogen on structure and magnetic properties of the formed compound layer. The thermal temperature has been measured at the vicinity of the samples. The compound layer thus produced has been characterized using, X-ray diffractometer and vibration sample magnetometer. Providing the total pressure of nitrogen and hydrogen is held constant, the addition of hydrogen up to 50% gives new structural phases. The magnetization values of the plasma treated samples are strongly dependent on the percentage of H_2 in the gas phase. An excessive amount of hydrogen (#approx#75%) on the other hand, retards the nitriding process. The surface temperature of the sample and plasma condition is crucial factors for nitriding process.
Interest in renewable and clean energies such as hydrogen has increased because of the high level of polluting emissions, increasing costs associated with petroleum and the escalating problems of global climate change. In the presence of a light source, a microbial photosynthetic process provides a system for the conversion of some organic compounds into biomass and hydrogen. Using Rhodopseudomonas palustris as a cell-factory, hydrogen photo-evolution was investigated in a photobioreactor (PBR) irradiated either from one or two opposite sides. Irradiating the photobioreactor from only one side, in the presence of malic acid, a reactor hydrogen production of 2.786 l(H{sub 2}) PBR{sup -1} was achieved. When the PBR was irradiated from two opposite sides, hydrogen photo-evolution increased to 3.162 l(H{sub 2}) PBR{sup -1}. Experiments were carried out using inoculum from either the ...
The use of absorbable polyglactin 910 mesh (Vicryl) is described in a case of Ewing's sarcoma of the pelvis. An operation was performed to hold the small bowel and colon out of the pelvis for a temporary period during which radical radiotherapy was delivered. The mesh allowed the temporary displacement of bowel and obviated bowel radiation morbidity. (author).
The application of kinetic probes that allow one to determine relative reactivities of biologically relevant substrates with oxidizing intermediates in the Fenton reagent (H2O2 plus Fe2+ in acidic aqueous...Full Text Available
The purpose of work is systematical studying of benzo (B) of thiophene-1,1-dioxides and their 2,3-di-hydro derivatives behaviour in the reactions of electrophflic, radical, nucleophilic nitration, reduction of nitro group, embodiment of synthesis of N-amino derivatives, investigation of sulfur containing hetero-cyclic compounds, including of residues of some steroids
Abstract A diacrylate polysulfone oligomer is synthesized and used as the acrylic oligomer for the in situ synthesis of noble metal/PSU nanocomposites through UV-induced simultaneous radical polymerization of acrylic functionalities and NP formation by reduction of their precursors. Thus, silver or gold NPs are formed in situ during polymer network formation. FESEM analysis of the morphology of the cured systems demonstrates that the nanoparticles of the noble metals are homogeneously distributed in the network without macroscopic agglomeration.
We demonstrate the nonuniqueness of the basic assumptions leading to spiral structure in self-propagating star formation models. Even in the case where star formation occurs purely spontaneously and does not propagate, we have generated spiral structure by adopting the radically different assumption where star formation is systematically inhibited.
The use of low rank coal leads to a reduction of the coke strength because of the reduction of the caking property of coking coal. The authors have tried to understand this mechanism by extracting and analyzing the caking component of low rank coal and coking coal. It was found that the caking component is decreased by radical attack from the low rank coal, and thus the caking property is reduced. 11 figs., 3 tabs.
There have been no radically new commercial bulk explosives since Atlas Powder Company's introduction of emulsions onto the market in 1968. But the effectiveness, safety and management of these familiar explosives is continuously being improved by the development of blast design techniques, explosives delivery and initiation systems, and monitoring methods. The author looks at developments in blasting technology and discusses experiences with Handibulk emulsion delivery systems.
DescriptionProgramme background Nanotechnology is the design and manufacture of substances typically between one and several hundred billionths of a metre in size. In this size range the properties of substances can change quite radically, offering potentially large socio-economic, health and environmental benefits. For example, nanofuel additives could help reduce emissions and particles from diesel engines. Nanoparticles may also be able to help remove persistent pollutants in soils and groundwaters. Th [continued...
The introduction of CT scan and, more recently, magnetic resonance imaging, has radically changed the diagnostic approach to tumors developed in the internal auditory canal and cerebellopontine angle. CT scan with intravenous injection visualizes tumors lying in the cerebellopontine angle. Magnetic resonance imaging, especially using gadolinium, is a very accurate means for diagnosing tumors of both the auditory canal and cerebellopontine angle.
Abstract High Post-Modernism with its understanding of the significance of the image anticipated the flattening of culture, first in advertising and the printed media, and more recently online. Sam Jacob of FAT speculates on architecture's relationship with the Internet, -a flatland of undifferentiated information-, and how Radical Post-Modernism might be best placed to resist the ubiquity of global culture while reanimating the social and cultural agenda of Modernism and Post-Modernism. Copyright 2011 John Wiley & Sons, Ltd.
In this paper nickel acetate catalyzed sodium borohydride cartridges have been prepared and hydrolyzed with water for hydrogen production. Two technological solutions have been tested to increase the overall hydrogen yield, namely a porous water diffuser and a hydrophobic membrane. The first was used to improve water diffusion inside the hydride while the second to confine water inside the cartridge. The generated hydrogen flow showed a very reproducible behavior. Hydrogen promptly evolved just after water was pumped into the cartridge. After some initial peaks, a constant hydrogen flow has been recorded for the whole reaction time. The constant flow was related to the presence of the porous diffuser. The use of a hydrophobic membrane to confine the water inside the cartridge allowed to increase the overall hydrogen yield: about 6 water molecules per mol of ...
This paper investigates various usages of natural gas (NG) as an energy source for different hydrogen production technologies. A comparison is made between the different methods of hydrogen production, based on the total amount of natural gas needed to produce a specific quantity of hydrogen, carbon dioxide emissions per mole of hydrogen produced, water requirements per mole of hydrogen produced, and a cost sensitivity analysis that takes into account the fuel cost, carbon dioxide capture cost and a carbon tax. The methods examined are the copper-chlorine (Cu-Cl) thermochemical cycle, steam methane reforming (SMR) and a modified sulfur-iodine (S-I) thermochemical cycle. Also, an integrated Cu-Cl/SMR plant is examined to show the unique advantages of modifying existing SMR plants with new hydrogen production technology. The analysis shows that the thermochemical ...
This paper investigates various usages of natural gas (NG) as an energy source for different hydrogen production technologies. A comparison is made between the different methods of hydrogen production, based on the total amount of natural gas needed to produce a specific quantity of hydrogen, carbon dioxide emissions per mole of hydrogen produced, water requirements per mole of hydrogen produced, and a cost sensitivity analysis that takes into account the fuel cost, carbon dioxide capture cost and a carbon tax. The methods examined are the copper-chlorine (Cu-Cl) thermochemical cycle, steam methane reforming (SMR) and a modified sulfur-iodine (S-I) thermochemical cycle. Also, an integrated Cu-Cl/SMR plant is examined to show the unique advantages of modifying existing SMR plants with new hydrogen production technology. The analysis shows that the thermochemical ...
In this paper, we present the work carried out within the framework of the FEVER project (Fuel cell Electric Vehicle for Efficiency and Range), an European project coordinated by Renault, joining Ecole des Mines de Paris, Ansaldo, De Nora, Air Liquide and Volvo. For the FEVER project, where an electrical air compressor is used for oxidant supply, there is no need for hydrogen spill over, meaning that the hydrogen stoichiometry has to be as close to one as possible. To determine the optimum hydrogen utilization efficiency for a 10 kW Proton Exchange Membrane Fuel Cell (PEMFC) fed with pure hydrogen, a 4 kW prototype fuel cell was tested with and without a hydrogen recirculator at the test facility of Ecole des Mines de Paris. Nitrogen cross over from the cathodic compartment to the anodic compartment limits the hydrogen utilization of the fuel cell without ...
A test to determine the lithium compatibility and impurity gettering capabilities of various materials including yttrium was performed in Beryllium-7 Experimental Lithium (7BELL) at 270/sup 0/C. Yttrium coupons were exposed in liquid lithium for a total of 3,718 hours. X-ray diffraction and bulk chemical analysis data indicated that yttrium absorbs hydrogen from liquid lithium at 270/sup 0/C and transforms to yttrium dihydride (YH/sub 2/). The transformation of yttrium to YH/sub 2/ resulted in embrittlement of the coupons and subsequent fragmentation to small pieces. Additional analysis, based on the equilibrium hydrogen pressures for the transition of yttrium to YH/sub 2/, and Sievert's relationship for hydrogen in equilibrium with hydrogen in lithium, indicates that the temperature of yttrium cannot exceed 280/sup 0/C to control the hydrogen concentration in lithium at ...
Ti-15Mo-2.7Nb-3Al-0.2Si (Timetal-21S), a metastable #beta#-titanium alloy, is a candidate material for titanium matrix composite structures in hydrogen-fueled hypersonic planes because of its excellent formability and adequate mechanical properties in the 500--800 C temperature range. The alloy is strengthened through the precipitation of fine #alpha# particles in the #beta# matrix. The mechanical properties and microstructures are controlled by a solutionizing/aging heat treatment. A major concern in using titanium alloys in hydrogen service is the embrittlement caused by the precipitation of hydrides. It is believed that the large solubility of hydrogen in the #beta#-phase would preclude the precipitation of hydrides in Beta titanium alloys, especially at low hydrogen pressures. However, depending on the hydrogen content, a shift in the ductile/brittle transition temperatures to ...
We demonstrate a two-step process used to increase the hydrogen yield from sucrose and to relieve the pollution threat caused by resultant fatty acids in dark-fermentation. In batch tests of dark-fermentation using microflora, the maximum hydrogen production rate was >360 mL H{sub 2}/Lh and the maximum hydrogen yield was 3.67 mol H{sub 2}/mol sucrose. The fatty acids produced in dark-fermentation were mainly butyrate and acetate with a small amount of propionate, valerate, n-butyl alcohol, and caproate. Photo-fermentation with Rhodobacter sphaeroides SH2C was then employed to convert these small molecular fatty acids into hydrogen. The total hydrogen yield from sucrose increased from the maximum of 3.67 mol H{sub 2}/mol sucrose in dark-fermentation to 6.63 mol H{sub 2}/mol sucrose by using the two-step process. No butyrate, acetate, propionate, or valerate was detected in the ...
This paper deals with construction types of high temperature heat exchangers, their circulation loops and temperature differences. Most attention is given to gas dynamics, convective heat transfer, convection and radiant heat transfer interaction in high temperature heat exchangers. The ways of heat transfer augmentation and efficient heat exchanger construction are discussed.
Heat transfer has emerged as a leading-edge technology supporting the rapid pace of developments in science and engineering ranging from energy production to electronic cooling. Subjects covered at the 6th UK National Conference on heat transfer held at Edinburgh from 15-16 September 1999 include: convection; boiling and evaporation; condensation; numerical techniques; heat exchangers; radiation and combustion; conduction; two-phase flow and heat transfer augmentation. Fifteen of the papers are abstracted here.
Experimental investigation was carried out for friction factor and heat transfer coefficient in the case of a rotating tube with a twisted-tape insert for heat transfer augmentation. The data obtained were compared with existing data for a stationary tube with a twisted-tape insert. It has been observed that the enhancement in heat transfer offsets the rise in friction factor due to rotation, with respect to a plain tube under stationary conditions. A correlation has been proposed for the data obtained.
An efficient method of hydrogen storage in nano-porous carbons is its reversible sorption by electrochemical decomposition of a KOH water solution according to the following equation: C + xH{sub 2}O + xe{sup -} {yields} (CH{sub x}) + xOH{sup -} where (CH{sub x}) stands for the hydrogen inserted into the nano-porous carbon during charging and oxidized during discharging. Although various carbon materials have been investigated as hydrogen adsorbents, the information about the storage mechanism as well as the nature of the hydrogen/carbon interaction is still not sufficient. In order to extend the understanding of the process, carbon samples charged electrochemically were investigated by temperature programmed desorption (TPD). The nature of the hydrogen/carbon interaction was studied by electrochemical analysis at different temperatures. The TPD experiments consist of heating the ...
In this paper, numerical simulation of a concentric tube heat exchanger is presented to determine the convective heat transfer coefficient and friction factor in a smooth tube. Increasing the convective heat transfer coefficient can increase heat transfer rate in a concentric tube heat exchanger from a given tubular surface area. This can be achieved by using heat transfer augmentation devices. This work constitutes the initial phase of the numerical simulation of heat transfer from tubes employing augmentation devices, such as twisted tapes, wire-coil inserts, for heat transfer enhancement. A computational fluid dynamics (CFD) simulation tool was developed with CFX software and the results obtained from the simulations are validated with the empirical correlations for a smooth tube heat exchanger. The difficulties associated with the simulation of a heat ...
This experiment investigated the effects of free-stream turbulence intensity, length scale, Reynolds number, and leading-edge velocity gradient on stagnation-region heat transfer. Heat transfer was measured in the stagnation region of four models with elliptical leading edges downstream of five turbulence-generating grids. Stagnation-region heat transfer augmentation increased with decreasing length scale but an optimum scale was not found. A correlation was developed that fit heat transfer data for isotropic turbulence to within {+-}4 percent but did not predict data for anisotropic turbulence. Stagnation heat transfer augmentation caused by turbulence was unaffected by the velocity gradient. The data of other researchers compared well with the correlation. A method of predicting heat transfer downstream of the stagnation point was developed. 28 refs., 12 ...
This experiment investigated the effects of free-stream turbulence intensity, length scale, Reynolds number, and leading-edge velocity gradient on stagnation-region heat transfer. Heat transfer was measured in the stagnation region of four models with elliptical leading edges downstream of five turbulence-generating grids. Stagnation-region heat transfer augmentation increased with decreasing length scale but an optimum scale was not found. A correlation was developed that fit heat transfer data for isotropic turbulence to within #+-#4 percent but did not predict data for anisotropic turbulence. Stagnation heat transfer augmentation caused by turbulence was unaffected by the velocity gradient. The data of other researchers compared well with the correlation. A method of predicting heat transfer downstream of the stagnation point was developed. 28 refs., 12 ...
This investigation concerns the nonlinear dynamics of heat transfer from a surface using an upstream eddy promoter. A numerical model is developed for the coupled fluid flow and heat transfer process based on a modified MacCormack scheme. Numerical simulations are carried out to determine the response and heat transfer enhancement due to the promoter. The average heat transfer from a cavity floor is seen to be increased by a factor of approximately five over the unpromoted'' flow. Another interesting feature of the study is the nonlinear viscous flow dynamics from the cylinder-wall interaction which differ significantly from the familiar cylinder-free stream patterns.
This investigation concerns the nonlinear dynamics of heat transfer from a surface using an upstream eddy promoter. A numerical model is developed for the coupled fluid flow and heat transfer process based on a modified MacCormack scheme. Numerical simulations are carried out to determine the response and heat transfer enhancement due to the promoter. The average heat transfer from a cavity floor is seen to be increased by a factor of approximately five over the unpromoted'' flow. Another interesting feature of the study is the nonlinear viscous flow dynamics from the cylinder-wall interaction which differ significantly from the familiar cylinder-free stream patterns.
Heat transfer augmentation has developed into a major specialty area in heat transfer research and development. A bibliography of world literature on augmentation is presented. The literature is classified into passive augmentation techniques, which require no external power, and active techniques, which do require external power. The fourteen techniques are grouped in terms of their application to the various modes of heat transfer. Mass transfer is included for completeness. Key words are included with each citation for technique/mode identification. The total number of publications cited is 1,967, including 75 surveys of various techniques and 42 papers on performance evaluation of passive techniques. Patents are not included as they will be the subject of a future topical report.
The effects of catalytic metal additives on the hydrogen desorption properties of the submicrocrystalline magnesium hydride (#beta#-MgH_2) formed after hydrogenation of the Mg + 10 wt.%X (X = V, Y, Zr) mechanically (ball) milled composites were studied. The composites with catalytic metals were processed by controlled mechanical milling (CMM) in the magneto-mill Uni Ball Mill 5 under protective Ar atmosphere. X-ray diffraction of the milled powders revealed the formation of Mg nanograins (50-60 nm range) interdispersed with the nanograined metal additives within the powder particles. Scanning electron microscopy showed particle size reduction after milling. After activation and hydrogenation in a Sieverts-type apparatus under about 2 MPa pressure of hydrogen, the tetragonal #beta#-MgH_2 hydride co-exists with the small amount of retained unreacted Mg phase and the small amount of MgO in all three ...
A number of properties in steel components are detrimentally influenced when exposed to hydrogen environments. Under these conditions, atomic hydrogen is adsorbed on the steel surface, then absorbed and preferentially transported towards tri-dimensional stressed regions in the crystal lattice and into defects such as interfaces or dislocations. The hydrogen embrittlement susceptibility is strongly influenced by various microstructural parameters including the type of inclusions, steel composition and heat treating conditions. One of the alternatives employed in minimizing hydrogen embrittlement is the use of surface barriers for hydrogen permeation. In particular, the presence of surface nitride layers in steels can be considered as an effective barrier. Nitride steel surface layers can be produced by plasma nitriding with the concomitant benefits of improved surface hardness, as ...
Large scale experiments were performed to determine the effectiveness of thermal glow plug igniters to burn hydrogen in a condensing steam environment due to the presence of water sprays. The experiments were designed to determine if a detonation or accelerated flame could occur in a hydrogen-air-steam mixture which was initially nonflammable due to steam dilution but was rendered flammable by rapid steam condensation due to water sprays. Eleven Hydrogen Igniter Tests were conducted in the test vessel. The vessel was instrumented with pressure transducers, thermocouple rakes, gas grab sample bottles, hydrogen microsensors, and cameras. The vessel contained two prototypic engineered systems: (1) a deliberate hydrogen ignition system and (2) a water spray system. Experiments were conducted under conditions scaled to be nearly prototypic of those expected in Advanced Light Water ...
Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass ...
A heat transfer (condenser) of a domestic freezer was tested in a vertical channel in order to study the influence of the chimney effect in the optimization of the heat transfer coefficient. The variation of the opening of the channel, position and the heating power of the heat exchanger in the heat transfer coefficient was considered. The influence of the surface emissivity on the heat transfer by thermal radiation was studied with the heat exchanger testes without paint and with black paint. The air velocity entering the channel was measured with a hot wire anemometer. In order to evaluate the chimney effect, the heat exchanger was testes in a open ambient. This situation simulates its operational conditions when installed on the freezer system. The variables collected in the experimental procedures was gathered in the form of dimensionless parameters as Nusselt, Rayleigh, Grashof and Prandtl numbers, ...
The authors discuss a two-phase two-component experimental system developed to study enhancement of heat transfer from a vertical chip size heater to surrounding liquid (Freon 113 or Ethanol) due to air jet impingement. Heat transfer coefficient was measured as function of jet velocity, heat flux and the distance between exit of jet tube and heated surface. The injector was placed very close to the hot surface. It was found that the heat transfer was notably enhanced with foreign gas impingement, especially in the cases of small temperature differences between wall and coolant. In fact for higher jet velocities the heat transfer coefficients tended to infinite while the temperature differences between wall and coolant were zero. The heat transfer coefficients decreased with the increasing of heat flux. High-speed camera was used to study the behaviour of the gas bubbles which play ...
Several heat transfer augmentation mechanisms contribute to the heat transfer augmentation around the stagnation point in the gas-solid two-phase impinging jet flow. Among those contributions, that of heat exchange was numerically analyzed and characteristically elucidated by the unsteady direct contact heat conduction at the time of impingement between the laden particles and heat transfer surface. In other words, if the contact time is short between the particles and heat transfer surface, the former is heated by heat stored in the latter as a heat capacity. In such a region, the heat quantity to be transferred to the particles changes by not only the thermal property value (heat capacity multiplied by heat conduction coefficient) of particles but also that of heat transfer surface. Then by using several kinds of particles and heat ...
This paper describes an investigation of electrodeposited Zn-14% Ni and aluminium-based SermeTel 1140/962 coatings as possible replacements for cadmium. Slow strain rate tests were performed to measure the extent of direct hydrogen embrittlement of a high strength steel substrate as a result of the coating process and of hydrogen re-embrittlement caused by coating corrosion. The level of re-embrittlement was shown to depend on both the electrochemical potential of the coating and its barrier properties. Zn-14% Ni coatings caused the most re-embrittlement as they had the most active potential and contained through-thickness defects which left the steel exposed to hydrogen uptake. The microstructure of the high strength steel was also shown to be an important factor affecting the extent of embrittlement. AerMet 100 steel was more resistant than 300M steel and this was attributed to the presence of reverted austenite ...
The possibility of obtaining high yields of hydrogen through the exposure of calcium hydroxide to natural uranium fission fragments is confirmed experimentally. The amounts of hydrogen obtained in some experiments were determined not only from the mass-spectrometry data, but also with the use of standard chemical analysis methods. The radiolytic hydrogen yield averaged over six independent experiments comprises 20.41 hydrogen molecules per 100 eV of absorbed fission fragment energy. The corresponding energy efficiency makes up to 60.62. Since on interaction with water or water vapor calcium hydroxide enters into the exothermal reaction to liberate 15.6 kcal/mole, it can easily be regenerated; this was attested to by one of irradiation experiments. Therefore, in the long run, we are dealing with a radiolytic decomposition of water at low temperatures or at temperatures readily available with modern ...
A quantitative energy pathway comparison is made between a modern oil refinery and genetic fusion hydrogen plant supporting hybrid-electric cars powered by gasoline and hydrogen-optimized internal combustion engines, respectively, both meeting President Clinton's goal for advanced car goal of 80 mpg gasoline equivalent. The comparison shows that a fusion electric plant producing hydrogen by water electrolysis at 80% efficiency must have an electric capacity of 10 GWe to support as many hydrogen-powered hybrid cars as one modern 200,000 bbl/day-capacity oil refinery could support in gasoline-powered hybrid cars. A 10 GWe fusion electric plant capital cost is limited to 12.5 B$ to produce electricity at 2.3 cents/kWehr, and hydrogen production by electrolysis at 8 $/GJ, for equal consumer fuel cost per passenger mile as in the oil-gasoline-hybrid pathway.
This document summarizes work done at the Astronautics Technology Center of the Astronautics Corporation of America (ACA) in Phase 1 of a four phase program leading to the development of a magnetic liquefier for hydrogen. The project involves the design, fabrication, installation, and operation of a hydrogen liquefier providing significantly reduced capital and operating costs, compared to present liquefiers. To achieve this goal, magnetic refrigeration, a recently developed, highly efficient refrigeration technology, will be used for the liquefaction process. Phase 1 project tasks included liquefier conceptual design and analysis, preliminary design of promising configurations, design selection, and detailed design of the selected design. Fabrication drawings and vendor specifications for the selected design were completed during detailed design. The design of a subscale, demonstration magnetic hydrogen liquefier ...
The behaviour of hydrogen adsorption on palladium has been investigated by a.c. impedance measurements in 0.1 M NaOH solution of pH 13 at 298 K. The electrode impedance has been measured by superimposing an a.c. voltage of 5 mV amplitude ranging between 10{sup -1} and 10{sup 4} Hz on a d.c. potential range from -0.76 to 0.44 V (standard hydrogen electrode (SHE)). The equivalent circuit representing the hydrogen adsorption reaction is proposed from the analysis of the frequency dependence of electrode admittance. The capacitance, arising from the adsorbed hydrogen, has been determined as a function of applied potential by complex non-linear least-squares curve fitting method based on the proposed equivalent circuit. As the cathodic applied potential increased from -0.36 to -0.76 V (SHE), the adsorption capacitance considerably increased owing to the enhanced coverage of hydrogen ...
The purpose of this work was to investigate the role of chromium on hydrogen embrittlement of Ni-Cr-Fe alloys and thus to develop a better understanding of the low-temperature stress corrosion cracking (SCC) phenomenon. The effect of chromium on hydrogen embrittlement was examined using tensile tests followed by material evaluation via scanning electron microscopy (SEM) and light optical microscopy. Four alloys were prepared with chromium contents ranging from 6 to 35 wt pct. In the uncharged condition, ductility, as measured by the percent elongation or reduction in area, increased as the alloy chromium content increased. Hydrogen appeared to have only minor effects on the mechanical properties of the low-chromium alloys. The addition of hydrogen had a marked effect on the ductility of the higher-chromium alloys. In the 26 pct chromium alloy, the elongation to failure was reduced from 53 to 14 pct, ...
S>Hydrogen-induced delayed failure in an alpha-beta titanium alloy (4Al-- 4Mn) was sensitive to microstructure. A quenched structure was less susceptible to delayed failure than aged or annealed structures. The tendency for delayed failure was magnified in all structures by an increase in hydrogen content or an increase in strength level. Hydrogen-induced delayed failure occurred by a process of crack initiation and controlled crack growth. Delayed failures resulting from creep were also encountered. Plastic strain resulting from creep tended to retard crack initiation. Changes occurring in material under static load prior to formation of cracks were reversible, as long as no appreciable plastic strain occurred, indicating stress-induced diffusion of hydrogen. Hydrogen-induced delayed failure disappeared at both high and low temperatares. The time ...
Hydrogen is a potential alternative energy source and produced commercially by methane (natural gas) or LPG steam reforming, a process that requires high temperatures, which are produced by burning fossil fuels. However, since this process emits large amounts of CO_2, replacement of the combustion heat source with a nuclear heat source for 773-1173 K processes has been proposed in order to eliminate these CO_2 emissions. This paper proposes a novel method of low-temperature nuclear hydrogen production by reforming dimethyl ether (DME) with steam produced by a low-temperature nuclear reactor at about 573 K. The authors identified conditions that provide high hydrogen production fraction at low pressure and temperatures of about 523-573 K. By setting this low-temperature hydrogen production process at about 573K upstream from a turbine, it was found theoretically that the total energy utilization ...
The conversion of off-peak surplus electricity into peak electricity through an electrolyzer, hydrogen storage, and fuel cell energy storage system was discussed. Development efforts in high pressure alkaline electrolysis and Proton-Exchange Membrane (PEM) fuel cells have improved the near-term viability of these systems. Potential use of wind turbines and other renewable energy-based generation systems, through hydrogen-based energy storage, were discussed as a new supply of surplus electricity. An integrated set of nomographs were presented for providing quick estimates of peak electricity costs derived from an electrolyzer/hydrogen fuel cell system. The nomographs allowed first order cost comparisons of centralized versus distributed hydrogen energy systems considering trade-offs between production economies of scale and hydrogen storage and transport costs. Use of the nomographs ...
Shell Oil's exploration of profitable business opportunities afforded by fuel cells and by the emergence of a viable hydrogen economy is discussed. The emphasis in this paper is on the transportation sector, particularly the importance of a refueling infrastructure and the influence that consumer attitudes will have on which technological solution will gain the upper hand in hydrogen-powered vehicle development. Key issues facing the oil industry with regard to development of hydrogen as the new energy carrier are also reviewed. Methanol reformer fuel cell cars are the most likely to gain acceptability in the short term, but the probability of methanol fuel cell vehicles being replaced by gasoline or hydrogen fuelled fuel cell vehicles or be superseded by advances in internal combustion engine and after-treatment technology, are very real. Government regulations, fiscal incentives and societal pressures ...
The Wind2H2 system is fully functional and continues to gather performance data. In this report, specifications of the Wind2H2 equipment (electrolyzers, compressor, hydrogen storage tanks, and the hydrogen fueled generator) are summarized. System operational experience and lessons learned are discussed. Valuable operational experience is shared through running, testing, daily operations, and troubleshooting the Wind2H2 system and equipment errors are being logged to help evaluate the reliability of the system.
An investigation of the effect of blending of two different coals in various ratios on the hydrogenation reaction was carried out using a red mud-sulphur catalyst. Three Japanese coals and an Australian brown coal were used in the study. The conversion of the blended coals was compared with that obtained with each of the coals alone. A blend of the Yallourn brown coal and Shin-Yubari coal showed a synergism: it is considered that hydroaromatics from the Japanese coal promote the hydrogenation of the Yallourn coal. (The tables and captions in this paper are in English).
An anisotropic power spectrum will have a clear signature in the 21cm radiation from high- redshift hydrogen. We calculate the expected power spectrum of the intensity fluctuations in neutral hydrogen from before the epoch of reionization, and predict the accuracy to which future experiments could constrain a quadrupole anisotropy in the power spectrum. We find that the Square Kilometer Array will have marginal detection abilities for this signal at z~17 if the process of reionization has not yet started; reionization could enhance the detectability substantially. Pushing to higher redshifts and higher sensitivity will allow highly precise (percent level) measurements of anisotropy.
Having simple and highly symmetric structure, solid hydrogen is a useful matrix on the study of radiation-chemical processes in solid phase which have been less understood in previous studies. We have found three outstanding findings: resonance effects on the tunneling reaction H+H{sub 2} {yields} H{sub 2} + H, effects of pressure on the dissociation and recombination of H{sub 2} molecules in solid hydrogen, and high-resolution ESR spectroscopy using a solid parahydrogen matrix. (author)
Hydrogen and helium cosmic ray nuclei spectra gathered from 1976 to 1993 have been corrected to the top of the atmosphere and normalized at high rigidities. The variation of these primary cosmic ray fluxes above 400 MeV/nucleon has been examined as a function of the phase of the solar cycle with the force-field approximation model. The intensity of the normalized fluxes between solar maximum and minimum conditions varies by a factor of 6 for hydrogen and a factor of 4.3 for helium at the lowest rigidities considered.
Cesium recovery from the polluted layers in the 1/3 scale hydrogen negative ion source for LHD-NBI system has tested. It was found, that the cesium recovery can be produced by additional discharges as from the cesium layer, aged by tungsten and residual gas, so as from the cesium layers, polluted by an occasional water leak. The highest cesium recovery to NI production was produced by a xenon arc, while glow discharge and arcing in hydrogen were less effective. The mechanism of recovery is the ejection of cesium from the underlying enriched layer by the arc and its transport to the surface. (author)
Four high-sulphur low-rank coals have been treated at hydrogenation conditions with three iron-based catalyst precursors: Red Mud (Fe[sub 2]O[sub 3]), iron sulphide and iron pentacarbonyl. The obtained yields show a dependence with the sulphur content of the coals; the organic sulphur content correlates with the conversion and THF-solubles when Red Mud and iron sulphide are added. In spite of the high hydrogen sulphide partial pressure in the reaction, the addition of other sources of sulphur enhances the percentages in conversion products. 15 refs., 2 figs., 3 tabs.
Inactivation of aflatoxin B1 was studied by using gamma radiation and hydrogen peroxide. A 100-krad dose of gamma radiation was sufficient to inactivate 50 micrograms of aflatoxin B1 in the presence of 5% hydrogen peroxide, and 400 krad was required for total degradation of 100 micrograms of aflatoxin in the same system. Degradation of aflatoxin B1 was confirmed by high-pressure liquid chromatographic and thin-layer chromatographic analysis. Ames microsomal mutagenicity test showed loss of aflatoxin activity. This method of detoxification also reduces the toxin levels effectively in artificially contaminated groundnuts.
This paper describes the results obtained from two large experimental facilities built at Sandia National Laboratories in Albuquerque, NM. FLAME (Flame Acceleration Measurements and Experiments) is a large horizontal rectangular channel designed to study flame acceleration, transition to detonation, simulation of combustion in containment geometries, component heating, and other problems in hydrogen combustion relevant to reactor safety. The Heated Detonation Tube has been designed to study detonations in hydrogen-air-steam mixtures. Both facilities have been in operation for just over a year. 12 figures.
This paper describes the results obtained from two large experimental facilities built at Sandia National Laboratories in Albuquerque, NM. FLAME (Flame Acceleration Measurements and Experiments) is a large horizontal rectangular channel designed to study flame acceleration, transition to detonation, simulation of combustion in containment geometries, component heating, and other problems in hydrogen combustion relevant to reactor safety. The Heated Detonation Tube has been designed to study detonations in hydrogen-air-steam mixtures. Both facilities have been in operation for just over a year. 12 figures.
During a hypothetical severe incident in a nuclear power plant with core meltdown a large part of radioactive material is present as aerosol particles in the reactor containment. In current severe accident containment codes the potential influences of hydrogen combustions on the behaviour of aerosols are not considered. Among other effects dry resuspension can increase the aerosol concentration in the atmosphere. Already deposited aerosol material can be re-released into the containment atmosphere by atmospheric currents induced by hydrogen deflagrations or by other phenomena like steam explosions. The objective is to assess the possible influence of this dry resuspension effect on the radioactive source term. (author)
Some recent achievements in the field of high pressure vessels and safety devices have offered a concrete chance to the application of compressed hydrogen for fleet commercial vehicles for urban use. Accordingly with this concept, ENEA has modified a Fiat Ducato van with a dual fuel engine, retaining the gasoline tank for long distance travelling and adopting the external mixture formation technique, with hydrogen injectors developed by ENEA, for non-polluting short-range duties in urban traffic. The article deals with the rationale for this choice and gives a general view of the project. (author)
A process is provided for conducting organic compound conversion over a catalyst composition comprising a specially treated crystalline zeolite having a high initial silica-to-alumina mole ratio, said zeolite having been synthesized from a reaction mixture comprising a diamine as a cation source. The treatment of the zeolite material comprises the sequential steps of reacting the zeolite with a dilute hydrogen fluoride solution, contacting the hydrogen fluoride solution reacted material with aluminum chloride vapor, and then treating the aluminum chloride contacted material to convert it to hydrogen form.
Use of hydrogen absorbing alloys in various practical applications is always connected with the problem of production of starting alloys. The transition from laboratory samples to small-scale production involves the change of furnace and its operation mode and this has an effect on the preparation method of mixture of starting metal. Also, for some applications such as thermosorption compressors the exact values of thermodynamical parameters of reaction are needed. In the present work we present the results of investigation of series Laves phase hydrogen-absorbing alloys which can be promising in for use in different devices. 1 ref.
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy transfer, is investigated. This technique is ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy transfer, is investigated. This technique is ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. An initial analytic study was done by Fisch and Rax. Here the authors calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favorable for wave amplification from alpha energy. They find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the energy ...
Heat-transfer augmentation by straight grid spacers in rod bundles is studied for single-phase flow and for post-critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single-phase flow is also examined. Governing heat-transfer mechanisms are analyzed, and predictive formulations are established. For single-phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. The effect of local velocity increasing near swirling spacer is considered. For post critical heat flux (CHF) dispersed flow, the heat transfer by thermal radiation, fin cooling, and vapor convection near the spacer are calculated. The predictions are compared with experimental data with satisfactory agreement.
An experimental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 m/s. An illustrative example of the use of the theory for industrial ventilation is presented. (author)
Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m{sup 2}K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)
Fundamental phenomena of condensation heat transfer at a steam-water interface have been studied related to the thermo-hydrodynamics of the emergency core cooling system for light water reactors. In this study temperature fluctuations near the interface and in the liquid phase were measured using fine thermocouples for a saturated steam-subcooled water co-current stratified two-phase flow in a nearly horizontal rectangular channel, and heat transfer coefficients were determined experimentally. The values of the condensation heat transfer coefficients in this experiment are from 6 to 40 kW/m"2K. In the regions of high Reynolds numbers, as the steam Reynolds numbers become larger, the average interfacial heat transfer coefficients tend to increase. The corelations of Nusselt numbers were obtained from the heat transfer data. (author)
A metal matrix is inserted into a phase-change material to enhance the heat transfer during phase-change processes. The metal matrix tends to act like a heat transfer fin from the heated or cooled surface and to increase the effective thermal conductivity of the phase-change fluid. The scope of the study involves numerically modeling the heat transfer to and from constant-temperature cylindrical tubes surrounded by water during the freezing and melting processes. Comparisons of heat transfer with and without the metal matrix are made, with different porosities and densities of the metal matrix being examined. The results of this study are discussed in terms of the effectiveness of the metal matrix as a heat transfer enhancement device.
... Title : Wear Rate and Friction Coefficient in Liquid Nitrogen and Hydrogen of Steel Sliding on Polymer Laminates (Various Fabrics and Polymers. ...
Secondary energy can be described as a surplus of electrical energy in a hydropower because the lower demand of energy in some period of the day and the excess of water in the reservoir during the rainy periods. This study proposes the using of the excess of energy at Itaipu Bi nacional for electrolytically hydrogen production and ammonia for nitrogenous fertilizers. Ammonia is a raw material for nitrogenous fertilizers synthesis and produced using hydrogen and nitrogen from the atmosphere. This paper determines the minimal cost of hydrogen production and the capacity of hydrogen production, with this data and according the ammonia market for nitrogenous fertilizers in the Centre/South region was estimated the better capacity of ammonia production for one plant near Itaipu. The process of ammonia production using energy excess is the most environmental acceptable. (author)
Investigations of alternative renewable energy resources continue, with many studies concentrating on hydrogen storage. However, there are a few problems such as storage, transportation, delivery to the user and usage safely, to be addressed to facilitate commercialization and wide usage of the hydrogen. The absorbed form within the metal hydrides seems to be the best solution of this problem. Since Li is the lightest metal, it has the advantage as the stored amount of hydrogen mass ratio. LiBH{sub 4} production process was investigated using elemental Li, B and H{sub 2}. Spex type ball milling with tungsten carbide, stainless steel and zirconia type vessels, was used to mix the different amount of Li and B under argon atmosphere. X-ray diffraction pattern demonstrated that the LiB was obtained. A system was designed to provide a hydrogen atmosphere of 60 bars to force hydrogen into ...
The optical emission of excited H reflected from clean Cu(110) after impingement of H/sup +/ and H/sub 2//sup +/ in the energy range of 250 eV to 20 keV per nucleon at 70/sup 0/ angle of incidence to the surface normal was measured. For incident 10 keV H/sub 2//sup +/, the highest excited hydrogen state detected was the n=10 level. The Hsub(..cap alpha..) yield was found to be fluence and energy dependent. This effect is attributed either to fast sputtered hydrogen, surface roughness or to an increase with hydrogen concentration in electron states of p-like symmetry near the Fermi level of copper. The Hsub(..cap alpha..) yield per reflected nucleon shows approximately an exponential dependence on both projectile energy per nucleon and scattered particle reciprocal velocity perpendicular to the surface.
The optical emission of excited H reflected from clean Cu(110) after impingement of H"+ and H_2"+ in the energy range of 250 eV to 20 keV per nucleon at 70"0 angle of incidence to the surface normal was measured. For incident 10 keV H_2"+, the highest excited hydrogen state detected was the n=10 level. The Hsub(#alpha#) yield was found to be fluence and energy dependent. This effect is attributed either to fast sputtered hydrogen, surface roughness or to an increase with hydrogen concentration in electron states of p-like symmetry near the Fermi level of copper. The Hsub(#alpha#) yield per reflected nucleon shows approximately an exponential dependence on both projectile energy per nucleon and scattered particle reciprocal velocity perpendicular to the surface. (orig.).
To study #beta# #reversible# #omega#-transformation in pseudo-#beta#-titanium alloy VT30, doped by hydrogen, methods of X-ray diffraction and thermodifferential analyses are used. It is established that in the process of heating of the hardened alloy from 0.004-0.1% H first formation and then dissolution of #omega# phase take place. An increase in hydrogen content to 0.1% decreases thermal effect of the processes and does not affect the temperature of #beta# #reversible# #omega#-transformation. Introduction of hydrogen in the concentration of 0.2% and higher suppresses completely #beta# #reversible# #omega# - transformation. A decrease in heating rate displaces #beta# #reversible# #omega#-transformation to lower temperatures.
The effect of varying pD(11-13,7) on the reaction of hydrogen with (Co/sup 11/(CN)/sub 5/)/sup 3/- in deuterium oxide has been studied by using infrared spectroscopy to determine the ratio of (Co/sup 111/(CN)/sub 5/X)/sup 3/- (X=H,D) in the solids precipitated from the steady state under hydrogen. The results show that the uptake of hydrogen does not liberate a free proton and that the rate of (Co/sup 111/(CN)/sub 5/H)/sup 3/- -D/sub 2/,0 exchange increases with pD but becomes pD independent at pD 7 greater than 13,5.
Hydrogenation residue is the product left over when petroleum residue feedstocks (or coal) are treated by, e.g. the Veba Combi Cracking (VCC) process. Many tests in semitechnical and full-sized coke ovens were carried out with hydrogenation residue (HR) as an additive in coking coal blends for the production of blast furnace coke or foundry coke. The results of the investigations reported in this paper demonstrate that HR is a very promising alternative for enlarging the coking coal basis compared to other processes or the use of other additives. The application of HR on an industrial scale did not indicate any negative impact on the handling of the hydrogenation residue or on the operation of the coke oven battery.
The deuterium uptake behavior of Zr-2.5Nb pressure tubes in Wolsung Unit 1 was analyzed in terms of longitudinal location, operation time, and coolant temperature. The results were compared with those obtained from Canadian CANDU reactors. The amount of deuterium uptake was higher at the outlet part than at the inlet part and was also higher when subjected to a longer operation time and a higher coolant temperature. The hydrogen uptake of Zr-2.5Nb in a hydrogen gas atmosphere was dependent on the microstructure of the alloy. The aged Zr-2.5Nb consisting of {alpha}-Zr and {beta}-Zr phases. The hydrogen in the alloy decreased the rate of oxidation. This could be explained in terms of the cathodic controlled reaction of Zr-2.5Nb oxidation. (author)
In order to find the solution to the problem of depletion of conventional fuels and environmental pollution caused by them, new design concepts such as low heat rejection engines and alternate fuel vehicles have started to appear. The present study deals with the concept of alternate fuel vehicle using hydrogen as a fuel. Results of analytical study to minimize heat loss during the power stroke of a hydrogen fueled spark ignition engine have been presented. Effect of various design and operating parameters on heat losses using a simulation model developed by the authors have also been presented. The results shall be helpful in designing efficient hydrogen fuelled spark ignition engines. (orig.)
The SHARP cannon. Hydrogen is compressed in the tube on top, the gun barrel is on bottom. When Jules Verne wrote in 1865 "From Earth to the Moon" he ...
Turbine Afterword The SHARP cannon. Hydrogen is compressed in the tube on top, the gun barrel is on bottom. When Jules Verne wrote in 1865 "From Earth to the Moon" he envisioned...
One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases. 5 refs., 9 figs., 1 tab.
The values of X = 0.77, Z = 0.035, and Y = 0.195 and the stage of evolution of Procyon are determined from the evolutionary tracks and the results of an analysis of the chemical composition of the atmosphere.
A means of determination of a ctive hydrogen of hydroxyl, carboxyl, sulfhydryl, amino, amido and sulfonamido groups by chemical ionization mass spectrometry using ammonia and trideuterioammonia as reagent gases is described. The method is based on exchange of active hydrogen for deuterium occurring during the chemical ionization process using trideuterioammonia, with comparison of m/z for ammonium adduct [M + NH1]+ and trideuterioammonium adduct [M--nH + nD + ND4]+, or of protonated molecular ion [M + H]+ and deuteronated molecular ion [M--nH + nD + D]+ yielding the number of active hydrogens. Applications have been made to several classes of biologically important compounds. PMID:427257
Red mud has been activated by dissolution in hydrochloric acid and reprecipitation with ammonia. The activated material has been evaluated as a catalyst for the hydrogenation of naphthalene, phenanthrene and pyrene and in the hydroliquefaction of both a high and low rank coal utilizing solvents of high and low hydrogen donating ability. Activation led to a substantial increase in the ability to hydrogenate the model compounds and a significant increase in oil yield was obtained in the hydroliquefaction of a low rank coal in the presence of a poor donor solvent. However, activation did not lead to significant increases in overall yields of liquids in other cases and the activated red mud was significantly less active than a commercial nickel-molybdenum-sulphur catalyst. 27 refs., 1 fig., 5 tabs.
A simple semianalytical calculation is used to study how a star reacts when its central stock of hydrogen is exhausted and before the next fusion reaction based on helium begins.
Mar 1, 2011 ... Molar extinction coefficients of hydrogen iodide in the Schumann region. Author: De More, W. B.; Raper, O. F.. Abstract: Molar extinction ...
W. E. B. Du Bois, one of the brightest lights in African American history, wrote a sparkling critique of the American social and economic system originally planned as part of the Bronze Booklets series, edited and published by Alain Locke and the Associates in Negro Folk Education. The piece was never published and has, until now, been lost to the annals of adult education history. Using historical evidence, the authors examine Du Bois's Basic American Negro Creed and the circumstances that led to its exclusion from the series. It is argued that the Creed was far too radical for the liberal minded Carnegie Corporation and its leaders who were only interested in accommodating adult education for Blacks through the AAAE funded Bronze Booklets. The exclusion of the Creed represents an example of repressive tolerance by the AAAE.
The authors present a search for excited and exotic muon states {mu}*, conducted using an integrated luminosity of 371 pb{sup -1} of data collected in p{bar p} collisions at {radical}s = 1.96 TeV at the Tevatron with the CDF II detector. They search for associated production of {mu}{mu}* followed by the decay {mu}* {yields} {mu}{gamma}, resulting in the {mu}{mu}{gamma} final state. They compare the data to model predictions as a function of the mass of the excited muon M{sub {mu}*}, the compositeness energy scale {Lambda}, and the gauge coupling factor f. No signal above the standard model expectation is observed in the {mu}{gamma} mass spectrum. In the contact interaction model, they exclude 107 < M{sub {mu}*} < 853 GeV/c{sup 2} for {Lambda} = M{sub {mu}*}; in the gauge-mediated model, they exclude 100 < M{sub {mu}*} < 410 GeV/c{sup 2} for f/{Lambda} = 10{sup -2} GeV{sup -1}. These 95% confidence level exclusions extend previous limits ...
A number of amines can be employed for all volatile treatment (AVT) of steam generator (SG) systems of nuclear power reactors. These amines form complexes with Cu{sup 2+} and Ni{sup 2+} ions which come into water due to corrosion. The redox reactions of a number of Cu(II)-AVT amine complexes and the stability of the transient species formed have been studied by pulse radiolysis technique. Rate constants for the reaction of e{sub aq}{sup -} with a number of Cu(II)-amine complexes have been determined by following the decay of e{sub aq}{sup -} absorption. Stability of Cu(I)-amine complexes was studied by following the kinetics of the bleaching signal formed at the {lambda}{sub max} of the Cu(II) amine complex. Except for Cu(I)-triethanolamine complex all other Cu(I)-amine complexes were found to be stable. One-electron oxidation of Cu(II) amine complexes was studied using azidyl radicals for the oxidation reaction as OH radicals react with the ...
Erectile dysfunction following radical prostatectomy remains a frequent problem despite the development of nerve-sparing techniques. This erectile dysfunction is believed to be neurogenic, enhanced by hypoxia-induced structural changes which result in additional veno-occlusive dysfunction. Recently, daily use of intracavernous vasoactive substances and oral use of PDE5-inhibitors have been clinically studied for treatment of postprostatectomy erectile dysfunction. Since these studies showed benefits of "penile rehabilitation therapy," these effects have been studied in a preclinical setting. We reviewed experimental literature on erectile tissue preserving and neuroregenerative treatment strategies, and found that preservation of the erectile tissue by the use of intracavernous nitric oxide donors or vasoactive substances, oral PDE5-inhibitors, and hyperbaric oxygen therapy improved erectile function by antifibrotic effects and preservation of smooth muscle. ...
A measurement of the t{bar t} production cross section at {radical}s = 1.96 TeV in the dilepton final states using a lepton+track selection and secondary vertex b-tagging is presented. One of the two leptons from the decay of the t{bar t} pair is allowed to be identified only as an isolated track to improve the selection efficiency. The result is combined with a measurement in the t{bar t} {yields} e{mu} final state. The measurements are based on 370 pb{sup -1} of data collected with the D0 experiment at the Tevatron collider. The preliminary cross section obtained in the combined lepton+track and e{mu} channel is: {sigma}{sub t{bar t}} = 8.6{sub -1.7}{sup +1.9}(stat) {+-} 1.1(syst) {+-} 0.6(lumi) pb.
The authors measure the dipion mass spectrum in X(3872) {yields} J/{psi}{pi}{sup +}{pi}{sup -} decays using 360 pb{sup -1} of {bar p}p collisions at {radical}s = 1.96 TeV collected with the CDF II detector. The spectrum is fit with predictions for odd C-parity ({sup 3}S{sub 1}, {sup 1}P{sub 1}, and {sup 3}D{sub J}) charmonia decaying to J/{psi}{pi}{sup +}{pi}{sup -}, as well as event C-parity states in which the pions are from {rho}{sup 0} decay. The latter case also encompasses exotic interpretations, such as a D{sup 0}{bar D}*{sup 0} molecule. Only the {sup 3}S{sub 1} and J/{psi} {rho} hypotheses are compatible with the data. Since {sup 3}S{sub 1} is untenable on other grounds, decay via J/{psi} {rho} is favored, which implies C = +1 for the X(3872). Models for different J/{psi}-{rho} angular momenta L are considered. Flexibility in the models, especially the introduction of {rho}-{omega} interference, enable good descriptions of the data for both L = 0 and 1.
Penile rehabilitation has been an area of intense study and debate over the last decade. Interest in this topic was stimulated by the observation that erectile dysfunction remained a significant problem after radical prostatectomy despite meticulous nerve-sparing technique. Smooth muscle alterations and fibrotic changes in the penis were identified as the underlying causes of penile atrophy, veno-occlusive dysfunction, and Peyronie's-like changes that were observed after surgery. Initial observations that intracavernous injection therapies used on a regular basis postoperatively resulted in improvements in the return of spontaneous erectile function led to the development of penile rehabilitation protocols. Chronic dosing of oral type V phosphodiesterase inhibitors is now commonly used by urologists after radical prostatectomy despite a lack of convincing evidence from randomized, placebo-controlled clinical trials. Use of local therapies to ...
The EUROTRAC sub-project ''Tropospheric Ozone Research'' (TOR) follows a dual strategy: - Observation of the chemical processes contributing to the oxygen balance directly in the atmosphere; - Establishment of a validated data base for model calculations. Both tasks require simultaneous measurements of a wide range of chemical and meteorological components. In the case of the investigation of the chemical processes, it is also desirable to measure the free radicals directly involved in ozone production. In the project described, a measuring station was set up. For a period of two years and a half, continuous measurements were made of ozone and its chemical precursors (NO, NO_2, NO_y, VOC, CO), as well as other photooxidants (H_2O_2 and organic hydroperoxides, organic nitrates), the photolysis frequency of NO_2, and meteorological parameters (wind, temperature, moisture, aerosols). The station was located on the Schauinsland mountain in the southern Black Forest, at ...
Microsecond pulse radiolysis of oxygenated aqueous solutions containing 0.02 mol dm"-"3 sodium formate and 2 mmol dm"-"3 phosphate buffer at pH 7 was used to generate superoxide anion radicals. The influence of some biologically important compounds upon the rate of O_2"."-"b"a"r decay as monitored spectrophotometrically in the range of 245-300 nm. Hematoporphyrin (HP), hemin C (HC), catalase (Cat), cobalt sulfophthalocyanine (CoTSPc) were studied. Among the investigated compounds only Cat was found to show a high catalytic efficiency towards the self-decay of O_2"."-"b"a"r. A red shift of 0_2"."-"b"a"r absorption band and slowing down of its decay were observed to take place by adding HP or CoTSPc to the solutions containing formate ions in excess. This effect is associated with the formation of a transient superoxo-complex. An appearance of an intermediate species with absorption maxima at 350 nm and half-life of about 2 s was observed to accompany the ...
The Green-Chasman lattice, which is the basis for both NSLS storage rings, was conceived with insertion devices in mind. Long, field-free straight sections were provided in the design. The electron optics were chosen so that these sections had zero dispersion and the effects of new magnetic structures placed in these regions would have minimal effect on the emittance of the electron beam. This design concept has been followed by all high-brightness rings which were built subsequent to the NSLS. The X-Ray Ring straight sections also have a very small vertical {beta} function, in addition to the zero dispersion. This was done to optimize the brightness of wiggler sources. There is a further benefit however. The {beta} function determines the beam size and divergence at a particular point in the storage ring lattice. The size is proportional to {radical}{beta} and the divergence is proportional to 1/{radical}{beta}. Thus the electron beam is very ...
The aim of present study was to evaluate antioxidant property of Glycyrrhiza glabra root extracts using in vitro models. The dose-dependent aqueous and ethanolic extracts demonstrated the scavenging activity against nitric oxide (concentration that caused 50% inhibition of nitric oxide radicals [IC(50)]=72 and 62.1 microg/ml, respectively), superoxide (IC(50)=64.2 and 38.4 microg/ml, respectively), hydroxyl (IC(50)=81.9 and 63 microg/ml, respectively), DPPH (IC(50)=43.6 and 28.3 microg/ml, respectively) and ABTS(*+) (IC(50)=77.3 and 57.2 microg/ml, respectively) radicals. Further, both extracts showed strong reducing power and iron-chelating capacities. In the Fe(2+)/ascorbate system, both extracts were found to inhibit mitochondrial fraction lipid peroxidation. In copper-catalyzed human serum and low-density lipoprotein oxidation models, both extracts significantly (P<0.05) lengthened the lag phase along with a decline in the oxidation ...
The addition of paraquat (methyl viologen) to a growing culture of Escherichia coli K-12 led within 1 hr to a 10- to 20-fold increase in the level of endonuclease IV, a DNase for apurinic/apyrimidinic sites. The induction was blocked by chloramphenicol. Increases of 3-fold or more were also seen with plumbagin, menadione, and phenazine methosulfate. H_2O_2 produced no more than a 2-fold increase in endonuclease IV activity. The following agents had no significant effect: streptonigrin, nitrofurantoin, tert-butyl hydroperoxide, #gamma# rays, 260-nm UV radiation, methyl methanesulfonate, mitomycin C, and ascorbate. Paraquat, plumbagin, menadione, and phenazine methosulfate are known to generate superoxide radical anions via redox cycling in vivo. A mutant lacking superoxide dismutase was unusually sensitive to induction by paraquat. In addition, endonuclease IV could be induced by merely growing the mutant in pure O_2. The levels of endonuclease IV in uninduced or ...
A methodology for assessing the impact of subacute concentrations of organometallic agents on bioenergetic and oxidative damage processes in animals, cells and energy transducing subcellular organelles is being developed. Several of the assays are noninvasive and thus lend themselves to human tests. At the whole-animal level we utilize a treadmill chamber where physiological parameters of exercising animals are monitored. These include parameters of whole animals' work performance such as oxygen consumption, carbon dioxide evolution and endurance. Oxidative damage can be monitored in experiments by analyzing expired air of the animals for ethane and n-pentane. These alkanes correlate with lipid peroxidation in vivo. At the cellular and subcellular levels, respiratory activity, lipid peroxidation and free radical species are assayed. Respiratory activity is measured in muscle homogenates and isolated mitochondria using substrates which feed into different ...
We present a systematic analysis of backward pion photoproduction for the reactions {gamma}p{yields}{pi}{sup 0}p and {gamma}p{yields}{pi}{sup +}n. Regge phenomenology is applied at invariant collision energies above 3GeV in order to fix the reaction amplitude. A comparision with older data on {pi}{sup 0}- and {pi}{sup +}-photoproduction at {theta}=180 indicates that the high-energy limit as given by the Regge calculation could be reached possibly at energies of around {radical}(s){approx_equal}3 GeV. In the energy region of {radical}(s){<=}2.5 GeV, covered by the new measurements of {gamma}p{yields}{pi}{sup 0} p differential cross-sections at large angles at ELSA, JLab, and LEPS, we see no clear signal for a convergence towards the Regge results. The baryon trajectories obtained in our analysis are in good agreement with those given by the spectrum of excited baryons. (orig.)
Related to other research on the effectiveness of flow boiling heat transfer augmentation using various types of turbulators this investigation comprises a definitive study of the effect of large discrete roughness elements on heat transfer over the entir...
The effect of velocity gradient on stagnation region heat transfer augmentation by free stream turbulence was investigated. Heat transfer was measured in the stagnation region of four models with elliptical leading edges with ratios of major to minor axes of 1:1, 1.5:1, 2.25:1, and 3:1. Four geometrically similar, square bar, square mesh, biplane grids were used to generate free stream turbulence with different intensities and length. Heat transfer measurements were made for the following ranges of parameters: Reynolds number, based on leading edge diameter, 37,000 to 228,000; dimensionless leading edge velocity gradient, 1.20 to 1.80; turbulence intensity, 1.1 to 15.9%; and length scale to leading edge diameter ratio, 0.05 to 0.30. Stagnation point heat transfer augmentation by free stream turbulence can be predicted using a modified version of a previously developed correlation for a circular leading ...
Semiclassical analysis of heavy ion induced transfer reactions are discussed for the quasielastic region. Some unique aspects of these reactions are shown, the variety of features which can be understood semiclassically is demonstrated, and some open problems are indicated. 28 refs., 16 figs. (LEW)
Plasmid transfer between strains of Bacillus thuringiensis subsp. israelensis was studied under a range of environmentally relevant laboratory conditions in vitro,...Full Text Available
The Subseabed Disposal Program has recently completed a 30-day, 0.286-scale laboratory simulation of an In Situ Heat Transfer Experiment (ISHTE), scheduled for eventual deployment in the deep ocean 600 nautical miles north of Hawaii. 10 figures.
The Subseabed Disposal Program has recently completed a 30-day, 0.286-scale laboratory simulation of an In Situ Heat Transfer Experiment (ISHTE), scheduled for eventual deployment in the deep ocean 600 nautical miles north of Hawaii. 10 figures.
Tetracycline-resistant Lactococcus lactis strains originally isolated from Polish raw milk were analyzed for the ability to transfer their antibiotic resistance genes in vitro, using...Full Text Available
This textbook contains the following main topics: Heat conductivity, convection, condensation and evaporation, radiation heat transfer and heat exchangers. It includes the physical foundations for all these aspects and many examples. (orig.)
A compact heat exchanger pedestal array for augmenting heat transfer in a machine is disclosed. The compact heat exchanger pedestal array includes a wall having first and second surfaces. The first surface faces a heated flow path and the second surface p...
Heating and cooling by impinging jets is widely used in various engineering applications, due to the high heat transfer rates prevailing in the vicinity of the stagnation point. The authors have been able to utilize acoustically excited turbulence for the...
An experimental investigation of heat transfer characteristics for various configurations of air jets impinging on the leading edge inner surface of a gas turbine blade wall is presented. Three configurations were investigated, namely a slot jet, a round ...
Equinovarus of the foot is the most common lower extremity deformity following traumatic brain injury. We evaluated outcomes of the split anterior tibialis tendon transfer (SPLATT) for correction of...Full Text Available
Scraped-surface heat transfer augmentation is proposed as a possible technique for use in improved air-cooling designs. Although it has been in common use with liquids, the technique has apparently never been used with gases. An experimental investigation...
Nuclear transfer (NT) is a procedure by which genetically identical individuals can be created. The technology of pig somatic NT, including in vitro maturation of oocytes, isolation and treatment of...Full Text Available
On February 27, 1990, standards for Benzene were promulgated for benzene transfer and benzene waste operations. The benzene enabling document summarizes these standards. The basic purpose of the document is to assist the EPA regional enforcement personnel...
An attempt is made to augment the heat transfer efficiency by means of inserting an oscillating thin plate into a tube of the shell and tube heat exchanger. However, the heat transfer augmenting mechanism has not been fully explained. To elucidate this heat transfer augmenting mechanism, an investigation was given on the heat transfer characteristics of a tube inlet at its preliminary run area when a double-hinged oscillating thin plate is inserted in the inlet. As a result of the experiment, the heat transfer augmentation in the tube as a result of inserting the double-hinged oscillating thin plate was found effective when the preliminary inlet run area is treated as the object. However, in comparison of the effect with the heat transfer in a fully developed turbulent region, it was {eta}- 1. The result thus obtained explains that no sufficient turbulence can ...
Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive ...
Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive ...
New partial differential equations (PDEs) for the full order weak schemes of the Langevin simulations are formulated. They are solved recursively in full order series solutions with respect to {radical}(t) (the full order weak Taylor schemes). Arbitrariness involved in the solutions is analyzed and clarified in detail. Specific solutions within some orders are presented as examples of the weak Taylor schemes. These PDEs and their solutions will serve for further developments of efficient higher order Runge-Kutta-like schemes. The similar formulation is possible for the imaginary time Hamiltonian evolution kernels as well. (orig.). 9 refs.
The reactions of native bovine catalase with superoxide and solvated electrons have been investigated using three different methods for generating these reducing substrates: [gamma]-radiolysis of oxygenated or deaerated buffer solutions in the presence of an OH radical scavenger; either xanthine or acetaldehyde with xanthine oxidase; and low-temperature (77 K) [gamma]-radiolysis of buffered ethylene glycol/water solutions with subsequent annealing of samples at 183 K. (Author).
Faced with a changing business emphasis, plus the need to reduce operations and maintenance costs in the North Sea, the Forties Field engineering partnership between BP and Brown and Root recognised the need to make radical changes in its organisational structure. An innovative change management programme was planned and executed inside 12 months with the purpose of right-sizing the Forties Operations Engineering team. Not only has the initiative succeeded in cutting costs by 40 per cent; it has also enhanced the quality of engineering support services supplied to the BP Forties platforms. (author)
Purpose: We present an update analysis of the multiinstitutional Ewing's sarcoma study CESS 86. Methods and Materials: From January 1986 through June 1991, 177 patients with localized Ewing's sarcoma of bone, aged 25 years or less, were recruited. Chemotherapy consisted of four 9-week courses of vincristine, actinomycin D, cyclophosphamide, and adriamycin (VACA) in low-risk tumors (extremity tumors =# 100 cm"3). Local therapy was an individual decision in each patient and was either radical surgery (amputation, wide resection) or resection plus postoperative irradiation with 45 Gy or definitive radiotherapy with 60 Gy (45 Gy plus boost). Irradiated patients were randomized concerning the type of fractionation in either conventional fractionation (once daily 1.8-2.0 Gy, break of chemotherapy) or hyperfractionated split-course irradiation simultaneously with the VACA/VAIA chemotherapy (twice daily 1.6 Gy, break of 12 days after 22.4 Gy and 44.8 Gy, total dose and ...
This article reviews antisocial personality disorder, psychopathy, and violence and develops a three factor model of personality traits. Then a discussion of related personality disorders precedes the development of a categorical two factor model of impulsive versus remorseless violence. A paradigm of proactive, medical, and school based early intervention and prevention is advocated as a useful addition to the reactive detention of criminal justice. Integration of psychological tests, neuroimaging, and genomic data in early childhood and school based intervention strategies to prevent the development of conduct disorder and attenuate criminal propensity inform this approach. PMID:20422651
This short communication aims to update the review of non-nitro radiation sensitizers (Shenoy and Singh 1985) and correct omissions. Work is mentioned and bibliography given for studied of cis-platinum, potassium permanganate, cobalt hexammine, sodium bromide, dimethylsulphoxide, zinc and copper ions, organic nitroxyl free radicals (TAN,TMPN and NPPN + PNAP), halogenated pyrimidines, organic and inorganic iodine containing compounds, diacetyl, acetone and acetophenone, rho-hydrobenzoic acid and its esters, pentobarbitone and secobarbitone, heparin and 9-anilinoacridines, dehydropiandosterone and paraquat. (U.K.).
Nano-materials in which a large fraction of atoms resides within a few atomic layers near the surface can be designed to have novel properties by manipulating their surface parameters. We show that the effective elastic constants of nano-porous/cellular materials can be made to exceed those of the parent materials provided the pore surface elastic parameters satisfy certain conditions. These stiff nano-porous materials herald a radical breakthrough in sandwich-type construction.
Nano-materials in which a large fraction of atoms resides within a few atomic layers near the surface can be designed to have novel properties by manipulating their surface parameters. We show that the effective elastic constants of nano-porous/cellular materials can be made to exceed those of the parent materials provided the pore surface elastic parameters satisfy certain conditions. These stiff nano-porous materials herald a radical breakthrough in sandwich-type construction.
Fractal dimensional analysis was employed to obtain a quantitative measure of the morphology of polymer networks formed by UV irradiation induced polymerization of photo-reactive mesogenic monomers dissolved in a liquid crystal host medium. The fractal dimensions obtained, may be interpreted by polymer network growth following a percolation-like model for monomer concentrations well below the solubility limit. On passing the solubility limit, the polymerization process changes from a (radical chain) solution polymerization to a dispersion polymerization, with fractal dimensions decreasing and suggesting a cluster-cluster aggregation process for monomer concentrations above the solubility limit, similar to the aggregation of colloidal particles.
Decomposition yields of tetracycline hydrochloride (TC.HCl) and chlorotetracycline hydrochloride (ClTC.HCl) in methanol solution saturated with Ar or N/sub 2/O were determined. Rate constants of the reaction esub(s)/sup -/ with some antibiotics were obtained. It was demonstrated by /sup 1/H NMR that the radical formed by degradation of 7-C-Cl group is recombined with the H atoms leading to ClTC.HCl being converted into tetracycline hydrochloride (TC.HCl).
We prove a cosmic no-hair theorem for Bianchi models in power-law inflation. Provided that the potential of an inflaton {phi} is exp({minus}{lambda}{kappa}{phi}) with 0{le}{lambda}{lt} {radical}2/3 , we find that the isotropic power-law solution is the unique attractor for any initially expanding Bianchi-type models except type IX. For Bianchi type IX, this conclusion is also true if the initial ratio of the vacuum energy to the maximum three-curvature is larger than one half.
The author presents a new technique for production of yellow cake with double precipitation, thus solving a series of problems for precipitating uranium with traditional double precipitation. The new technique can not only remove ferric ions and sulfate radicals but also make solid-liquid separation easy, utilize effectively the sulfuric acid produced in ferric ions precipitation process, and increase uranium concentration of leaching liquor. To take it as producing yellow cake will save investment, simplify operation, and cut down the consumption of raw materials and energies. It is more competitive than ion-exchange or solvent extraction in the process of extracting-purifying and preparing yellow cake.
... TTP tactics, techniques, and procedures UCP Unified ... be sold or transferred to Pakistan, pursuant to ... substantial amounts of those funds being spent ...
Ultrasonic enhancement of heat transfer on a narrow surface was measured by changing the width of the surface from 8 to 0.1 mm. Ultrasonic power of 600 W with a frequency of 40 kHz was used. Heat transfer on the narrow surface without ultrasonic vibration was correlated by the experimental equation for a thin wire. The cavitation intensity was measured by the cavitation erosion loss of an aluminum foil of 15 [mu]m thickness. The effects of acoustic streaming and cavitation were separated by this measurement. Heat transfer by acoustic streaming was predicted through forced convection. Enhancement by cavitation was explained by the turbulence thermal conductivity of the microjets.
The present study investigates the effect of the shear rate-dependent thermal conductivity of non-Newtonian fluids on the heat transfer enhancement in a pipe flow. The constant heat flux as thermal boundary condition was adopted in the thermally developed region. The present analytical results show the heat transfer enhancement over those of a shear rate-independent thermal conductivity fluid. The heat transfer coefficient ratio (h/h{sub 0}) linearly increase with the non-dimensional average velocity difference which is the product of the shear rate-dependence of the thermal conductivity and wall-shear rate.
A comprehensive presentation is made of state-of-the-art configurations and design methodologies for heat transfer devices applicable to industrial processes, automotive systems, air conditioning/refrigeration, cryogenics, and petrochemicals refining. Attention is given to topics in heat exchanger mechanical design, single-phase convection processes, thermal design, two-phase exchanger thermal design, heat-transfer augmentation, and rheological effects. Computerized analysis and design methodologies are presented for the range of heat transfer systems, as well as advanced methods for optimization and performance projection.
Unsteady impinging jets are systematically controlled with respect to their time dependence in order to investigate the influence of unsteadiness on the heat transfer performance. This is achieved by a special mass flow control device, which allows almost arbitrary shapes of unsteadiness to be imposed onto the impinging jet. Three different standard signals (sinusoidal, triangular, rectangular) and two specially designed signals are applied and their influence on heat transfer is determined in terms of an enhancement factor. Heat transfer augmentation up to 30% was found and could be physically explained with the help of PIV and hot-wire measurements of the flow field.
The concentric circular annular duct is a common geometry in many fluid flow and heat transfer devices. For the purpose of heat transfer augmentation, fins are often employed in the annular region, and such finned ducts find wide application in compact heat exchangers (5, 6). The analysis of flow and heat transfer in this geometry is, therefore, quite important from an engineering standpoint. For fully developed conditions, the problem has already been analyzed (7-10). However, no results are available for the developing flow in the entrance region. It is with this latter problem that the present paper is concerned.
This paper presents the results of the experimental investigation on heat transfer and fluid friction characteristics of a class of spiral spring coil used as a tube side forced convection heat transfer augmentation devices. Based on a lot of experimental data, the heat transfer correlation and fluid friction correlation revised by temperature were reached in terms of linear regression. At the same time, proper criteria were used to evaluate the economic performance of the spiral spring inserted tube according to the demand of practical application and some probing analysis were made.