Physics with Polarized Antiprotons
Energy Technology Data Exchange (ETDEWEB)
Polarized antiprotons produced by spin filtering with an internal polarized gas target provide access to a wealth of single- and double-spin observables, thereby opening a window to physics uniquely accessible with the HESR at FAIR. This includes a first measurement of the transversity distribution of the valence quarks in the proton, and a first measurement of the moduli and the relative phase of the time-like electric and magnetic form factors G{sub E,M} of the proton. In polarized and unpolarized pp-bar elastic scattering open questions like the contribution from the odd charge-symmetry Landshoff-mechanism at large |t| and spin-effects in the extraction of the forward scattering amplitude at low |t| can be addressed.
2006-04-15
The Development of 6061-Aluminum Windows for the MICE LiquidAbsorber
Energy Technology Data Exchange (ETDEWEB)
The thin windows for the Muon Ionization Cooling Experiment (MICE) liquid Absorber will be fabricated from 6061-T6-aluminum. The absorber and vacuum vessel thin windows are 300-mm in diameter and are 180 mm thick at the center. The windows are designed for an internal burst pressure of 0.68 MPa (100 psig) when warm. The MICE experiment design calls for changeable windows on the absorber, so a bolted window design was adopted. Welded windows offer some potential advantages over bolted windows when they are on the absorber itself. This report describes the bolted window and its seal. This report also describes an alternate window that is welded directly to the absorber body. The welded window design presented permits the weld to be ground off and re-welded. This report presents a ...
2005-08-24
Radiation hardening of diagnostics
International Nuclear Information System (INIS)
The world fusion program has advanced to the stage where it is appropriate to construct a number of devices for the purpose of burning DT fuel. In these next-generation experiments, the expected flux and fluence of 14 MeV neutrons and associated gamma rays will pose a significant challenge to the operation and diagnostics of the fusion device. Radiation effects include structural damage to materials such as vacuum windows and seals, modifications to electrical properties such as electrical conductivity and dielectric strength and impaired optical properties such as reduced transparency and luminescence of windows and fiber optics during irradiation. In preparation for construction and operation of these new facilities, the fusion diagnostics community needs to work with materials scientists to develop a better understanding of radiation effects, and to undertake a testing program aimed at developing workable solutions for this multi-faceted ...
Vapor fraction measurements in a steam-water duct at atmospheric pressure using neutron radiography
Energy Technology Data Exchange (ETDEWEB)
Real-time neutron radiography has been used to study the dynamic behavior of two-phase flow and measure vapor fractions in a steam-water duct at atmospheric pressure. This unique experimental technique offers one the opportunity to observe and record on videotape now Patterns and transient behavior of two-phase flow inside opaque containers without perturbing the environment. The neutron radiographic technique is non-intrusive and requires no special transparent window region. Data are recorded simultaneously over a large area of interest. Image processing of the video data can be employed to measure bubble velocities and time-averaged and Instantaneous vapor fractions.
1994-11-11
An overview of beta titanium alloy environmental behavior
International Nuclear Information System (INIS)
Stemming from their unique combination of elevated strength, low density, and good overall corrosion resistance, beta titanium alloys have become attractive candidate materials for critical, high-stress, components in corrosive services. An overview of the comparative corrosion resistance of beta alloys to conventional alpha and alpha/beta titanium alloys in common industrial and aerospace service environments generally reveals attractive behavior depending on the environment and alloy composition and, in some cases, alloy condition. Expanded performance windows are especially noted for the molybdenum-rich beta alloys, particularly in regard to resisting reducing acids, stress corrosion, and high temperature localized chloride attack, along with hydrogen and oxidation resistance. Where applicable, implications of this enhanced corrosion performance on current and perspective beta alloy applications are also noted.
1993-02-21
Numerical simulations of industrial processes involving fluid dynamics, combustion and radiation
Energy Technology Data Exchange (ETDEWEB)
Moving out of the scientific community research laboratories, computational fluid dynamics (CFD) software packages are now allowing industrials to analyse and optimize industrial processes involving the use of gases, liquids and even some two-phase fluids. Their attractiveness and their impact stems out from the opportunity they offer to bring insight into an existing unit, or even at the design stage, by displaying the spatial distribution of process relevant variables such as temperature, concentration. The filling of the spacing in between a two-layer window is a simple example. This new opportunity of visualisation is at times an unique way, when the process environment is an opaque one, such as liquid metal flowing into a tundish or when measurements of flows may be a long and tedious work, such as flows within water treatment basins. This environment we are to investigate in order to optimize can also be a harsh one, due to its high ...
1997-12-31
Computer Network Security: Best Practices for Alberta School Jurisdictions.
This paper provides a snapshot of the computer network security industry and addresses specific issues related to network security in public education. The following topics are covered: (1) security policy, including reasons for establishing a policy, risk assessment, areas to consider, audit tools; (2) workstations, including physical security, protecting workstation components, and computer viruses; (3) the local network, including the OSI (Open Systems Interconnection) reference model, protocols, network segmentation, network management, network sniffing, and data encryption; (4) servers, including UNIX and other server operating systems; (5) remote access, including technologies, remote access servers, protocols, and authentication/authorization; (6) crackers and hackers, including threats and hacking tools/techniques; (7) Internet firewalls, including functions, issues and problems, types, rules, logs, firewall accessories, buying a firewall, and firewall administration; and (8) ...
1999-02-01
ITER Core Imaging X-Ray Spectrometer Conceptual Design and Performance Assessment - Phase 2
International Nuclear Information System (INIS)
During Phase 2 of our study of the CIXS conceptual design we have tackled additional important issues that are unique to the ITER environment. These include the thermal control of the crystal and detector enclosures located in an environment with a 100-250 C ambient temperature, tritium containment, and the range of crystal and detector movement based on the need for spectral adjustments and the desire to make measurements of colder plasmas. In addressing these issues we have selected a ''Dewar''-type enclosure for the crystals and detectors. Applying realistic view factors for radiant heat and making allowance for conduction we have made engineering studies of this enclosure and showed that the cooling requirements can be solved and the temperature can be kept sufficiently constant without compromising the specification parameters of the CIXS. We have chosen a minimum 3 mm combined thickness of the six beryllium windows needed in a Dewar-type ...
We will present the first astronomical images taken with MIRSI (Mid-InfraRed Spectrometer and Imager). First light for MIRSI is scheduled for December 2001. MIRSI is a mid-infrared camera system recently completed at Boston University that has both spectroscopic and imaging capabilities. The camera utilizes a new 320x240 Si:As IBC array developed for ground-based astronomy by Raytheon/SBRC. MIRSI offers a large field of view (1.6 arcmin x 1.2 arcmin at the IRTF with a pixel scale of 0.3 arcsec), diffraction-limited spatial resolution, complete spectral coverage over the 8-14 micron and 17-26 micron atmospheric windows for both imaging (discrete filters and CVF) and spectroscopy (10 and 20 micron grisms), and high sensitivity (expected 1-sigma point source sensitivities of 5 and 20 mJy at 10 and 20 microns, respectively, for on-source integration time of 30 seconds). This system offers the unique ability to acquire both spectra and ...
2001-12-01
Perceptual training narrows the temporal window of multisensory binding
UK PubMed Central (United Kingdom)
The brain’s ability to bind incoming auditory and visual stimuli depends critically on the temporal structure of this information. Specifically, there exists a temporal window of audiovisual...Full Text Available
2009-09-30
UK PubMed Central (United Kingdom)
The mechanical properties of laminated window profiles manufactured using two types of adhesives were determined. The objective of this study is to evaluate the effects of heat treatment on some mechanical...Full Text Available
cookers can reach in a specified period of time. The students will also look at solar pasteurization of water and learn how the sun can ...
JPRS Report, Science & Technology, China, High-Power ...
... KDP crystal. ... The KDP crystal has a high nonlinear the degree of matching between the fluid and the window coefficient. ...
1991-10-18
Glass Fragment Hazard from Windows Broken by Airblast
... MATHEMATICAL PREDICTION, BODIES, SKIN(ANATOMY), SONIC BOOM, BIOPHYSICS, WOUND BALLISTICS, BONE FRACTURES, SKULL. ...
1980-05-30
Scintigraphic assessment of pericardio-peritoneal window patency. Relevance to peritoneal dialysis.
To alleviate recurrent pericardial effusion secondary to systemic lupus erythematosus, pericardio-peritoneal window was performed. Subsequently, end stage renal disease developed and the patient required peritoneal dialysis. Patency of the pericardio-peritoneal window was demonstrated by intraperitoneal injection of Tc-99m SC through a Tenckhoff catheter, which prompted special counsel to the patient in order to prevent infectious pericarditis potentially complicating peritoneal dialysis induced-peritonitis. PMID:7554664
1995-07-01
Energy Technology Data Exchange (ETDEWEB)
Real time neutron radiography has been used to study the dynamic behavior of two phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 cm and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 megawatt TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet water ...
1998-02-01
International Nuclear Information System (INIS)
Real-time neutron radiography has been used to study the dynamic behavior of two-phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam-water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two-phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 MW TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet water ...
1999-11-03
International Nuclear Information System (INIS)
Real time neutron radiography has been used to study the dynamic behavior of two phase flow and measure the time averaged vapor fraction in a heated metal tube containing boiling steam water operating at up to 15 bar pressure. The neutron radiographic technique is non-intrusive and requires no special transparent window region. This is the first time this technique has been used in an electrically heated pressurized flow loop. This unique experimental method offers the opportunity to observe and record on videotape, flow patterns and transient behavior of two phase flow inside opaque containers without disturbing the environment. In this study the test sections consisted of stainless steel tubes with a 1.27 cm outer diameter and wall thicknesses of 0.084 cm and 0.124 cm. The experiments were carried out at the Pennsylvania State University 1 megawatt TRIGA reactor facility utilizing a Precise Optics neutron radiography camera. The inlet water ...
1998-03-16
Fabrication of the 320-CM-OD all-ceramic ZT-40 torus
International Nuclear Information System (INIS)
The fabrication of the ZT-40 torus, a large complex all-ceramic toroidal plasma containment vessel, is described. Several glass sealants covering the temperature range of 500 to 1300"0C, were developed and used to ''braze'' segments of the torus together, sapphire windows to the torus and the required pump-out and diagnostic parts to the ceramic vacuum vessel. Designs of window seals were developed that allowed sealing of the sapphire windows in a vertical position with minimum sealing glass flow.
Direct laser initiation of PETN
Energy Technology Data Exchange (ETDEWEB)
In the early 1970s Yang and Menichelli demonstrated that direct laser illumination of low-density secondary explosive prr:ssings through a transparent window could produce detonation. 'The energy requirement for threshold initiation of detonation was reduced when a thin metal coating of metal covered the side of the window against which the low-density explosive was pressed. We have obtained experimental results that are in general agreement with the results of Renllund, Stanton and Trott (1 989) and recent: work by Nagayama, hou and Nakahara (2001). We report exploration of the effects of laser beam diameter, PEiTN density and specific surface area, and thickness of a titanium coating on the window.
2001-01-01
Removal Sampling to Calculate Population Statistics
Removal Sampling is an easy-to-use Windows program which calculates population statistics from removal trapping experiment data. Using maximum likelihood methods it ... ...
Radiative properties of a solar cavity receiver/reactor with quartz window
British Library Electronic Table of Contents (United Kingdom)
An energy transfer and conversion model for high-temperature solar cavity receivers has been developed using the transport behaviour of solar radiation as described by the spectral radiative exchange factors. A Monte-Carlo ray-tracing method coupled with optical properties was adopted, to predict radiation characteristics of the solar collector system by calculating radiative exchange factors. A cavity receiver with a plano-convexo quartz window was proposed, based upon the directional characteristics of the focal flux and the redistribution effect of the quartz window. Parametric studies on the windowed receiver provided a more uniform flux distribution, higher efficiency and lower loss than the windowless receivers. The predicted results serve as a design reference for the solar receiver...
2011-01-01
UK PubMed Central (United Kingdom)
For some neurotoxic chemicals, neurobehavioral effects are now considered to be among the most sensitive end points yet detected, particularly if exposures occur during critical windows of vulnerability....Full Text Available
1999-06-01
Development of L-band pillbox RF window
Energy Technology Data Exchange (ETDEWEB)
A pillbox RF output window was developed for the L-band pulsed klystron for the Japanese Hadron Project (JHP) 1-GeV proton linac. The window was designed to withstand a peak RF power of 6 MW, where the pulse width is 600 {mu}sec and the repetition rate is 50 Hz. A high power model was fabricated using an alumina ceramic which has a low loss tangent of 2.5x10{sup -5}. A high power test was successfully performed up to a 113 kW RF average power with a 4 MW peak power, a 565 {mu}sec pulse width and a 50 Hz repetition rate. By extrapolating the data of this high power test, the temperature rise of the ceramic is estimated low enough at the full RF power of 6 MW. Thus this RF window is expected to satisfy the specifications of the L-band Klystron. (author).
1994-12-31
A - Z Index : Environmental Energy Technologies Division
Buildings Energy-Efficient Research Laboratories Energy Efficiency in Federal Facilities Energy Efficiency Standards Group Energy Efficient Windows Collaborative Energy &...
2011-07-15
Observations of a Unique Type of ULF Waves by Low-Latitude Space Technology Five Mission
We report a unique type of ULF waves observed by low-altitude Space Technology 5 (ST-5)
2011-01-01
Kenai River Salmon ... a Unique Resource in South-Central ...
... Accession Number : ADA323711. Title : Kenai River Salmon ... a Unique Resource in South-Central Alaska. Descriptive ...
Target Diagnostic Instrument-Based Controls Framework for the National Ignition Facility
Energy Technology Data Exchange (ETDEWEB)
NIF target diagnostics are being developed to observe and measure the extreme physics of targets irradiated by the 192-beam laser. The response time of target materials can be on the order of 100ps--the time it takes light to travel 3 cm--temperatures more than 100 times hotter than the surface of the sun, and pressures that exceed 109 atmospheres. Optical and x-ray diagnostics were developed and fielded to observe and record the results of the first 4-beam experiments at NIF. Hard and soft x-ray spectra were measured, and time-integrated and gated x-ray images of hydrodynamics experiments were recorded. Optical diagnostics recorded backscatter from the target, and VISAR laser velocimetry measurements were taken of laser-shocked target surfaces. Additional diagnostics are being developed and commissioned to observe and diagnose ignition implosions, including various neutron and activation diagnostics. NIF's diagnostics are being developed at LLNL and with collaborators at ...
2007-05-07
O the Use of Time and Correlation Windows for Non-Parametric Spectral Analysis.
Available from UMI in association with The British Library. Requires signed TDF. Design of time and correlation windows for non -parametric frequency response estimates. The thesis deals with problems that arise in the field of spectral analysis due to finite observations of input and output records. In particular, it is concerned with the method of applying time and correlation windows in spectral analysis procedures to obtain non-parametric frequency response estimates of open-loop time invariant systems. The thesis reviews and develops the sources of error that arise when frequency response techniques are applied directly to windowed records of input and output data to estimate the frequency response of open loop systems. Having identified the cause of these errors, methods of eliminating or reducing them are studied. The techniques introduced involve the use of differing time windows for the input ...
1990-01-01
Energy Technology Data Exchange (ETDEWEB)
The effect of various window layers for InP solar cells are studied. Window materials that have type 1 and type 2 alignment in the window/emitter interface are compared. All window materials that form a type 2 alignment with InP, such as Al{sub 0.20}In{sub 0.80}P, Ga{sub 0.20}In{sub 0.80}P, Al{sub 0.55}In{sub 0.45}As and Al{sub 0.60}In{sub 0.40}P, cause a high interface recombination velocity, which deteriorates the carrier collection. This recombination takes place due to the spatially indirect quantum well transition between the triangular quantum wells formed in the interface. ZnSe as a window layer material with type 1 alignment does not have this problem, but still decreased response in the short wavelength region is observed due to misfit dislocation induced trap sites. Future prospects for the window layer development for InP are discussed. The discussion ...
1994-12-31
Calcium fluoride window mounting
International Nuclear Information System (INIS)
A technique has been developed for joining a large calcium fluoride crystal to a stainless-steel flange by means of a silver transition ring. The process involves both vacuum brazing using a copper-silver alloy and air brazing using silver chloride. This paper describes the procedure used in fabricating a high-vacuum leak-tight calcium fluoride window assembly.
Synthetic Biology and Human Health: Potential Applications for Spaceflight
Human space travelers experience a unique environment that affects homeostasis and physiologic
2011-01-01
... been possible to prove the existence and uniqueness of a classical solution which tends to the well-known solution of the Stefan problem as the ...
1989-01-01
A hybrid time-frequency method based on improved Morlet wavelet and auto terms window
British Library Electronic Table of Contents (United Kingdom)
In this paper, a hybrid time-frequency method (HTM) based on the improved Morlet wavelet and auto terms window (ATW) is presented. The Morlet wavelet, for its shape is similar to the mechanical shock signals, is added two parameters which decide the shape of the mother wavelet. The added parameters and the appropriate scale parameter for continuous wavelet transformation (CWT) are calculated using the cross validation method (CVM) and the minimum Shannon entropy method. The useless noise in the original signal can be filtered by the CWT filter de-noising process. An ATW based on the Smoothed Pseudo Wigner-Ville Distribution (SPWVD) spectrum is designed as a window function to suppress the cross terms in Wigner-Ville Distribution (WVD). The gear fault diagnosis experiment results show that ...
2011-01-01
UK PubMed Central (United Kingdom)
This paper summarizes the deliberations of a work group charged with addressing specific questions relevant to risk estimation in developmental neurotoxicology. We focused on eight questions. a) Does...Full Text Available
2000-06-01
UK PubMed Central (United Kingdom)
BackgroundPolychlorinated biphenyls (PCBs) may cause immunotoxic effects, but the detailed dose–response relationship and possible vulnerable time windows of exposure are...Full Text Available
2010-10-01
SIDE GROUP ADDITION TO THE PAH CORONENE BY UV PHOTOLYSIS IN COSMIC ...
a CsI window (for IR spectroscopy)andinto which the PAH wasisolated(Hudgins& ... I j.trnthick after30minutes,andtypically hadH20/PAH ratiosof ...
UK PubMed Central (United Kingdom)
Malignant gliomas are aggressive and angiogenic tumors with high VEGF content. Consequently, approaches such as metronomic chemotherapy, which have an antiangiogenic effect, are being investigated....Full Text Available
2011-07-01
UK PubMed Central (United Kingdom)
Human endometrium resists embryo implantation except during the 'window of receptivity'. A change in endometrial gene expression is required for the development of receptivity. Uterine calbindin-D28k...Full Text Available
Comparative Medicine - National Center for Research Resources...
and Antibody Responses of Rhesus Macaques Exposed to the Human Gammaretrovirus XMRV external link, opens in new window J Virol. 2011 May;85(9):4547-57 Detection of CWD...
2011-10-15
Cocurrent Steam/Water Flow in a Horizontal Channel.
Measurement of local steam condensation rates of cocurrent stratified flow of steam and subcooled water was carried out at atmospheric pressure in a horizontal rectangular channel. The channel was constructed of stainless steel with pyrex glass windows, a...
1981-01-01
30 CFR 77.1605 - Loading and haulage equipment; installations.
...2010-07-01 2010-07-01 false Loading and haulage equipment; installations. 77.1605 Section 77.1605...Loading and Haulage § 77.1605 Loading and haulage equipment; installations. (a) Cab windows shall...
2010-07-01
Onboard Systems Record Unique Videos of Space Missions - NASA
May 1, 2011 ... Onboard Systems Record Unique Videos of Space Missions ... Corporation, An artist's rendering of LCROSS launching toward the Moon .... Station (ISS) as part of the Commercial Orbital Transportation Services program. ...
...dates of the implementation of the standard unique health identifier for health care providers. 162.404 Section 162.404 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES ADMINISTRATIVE DATA...
2010-10-01
Ventilation by the windows in classrooms: a case study
Energy Technology Data Exchange (ETDEWEB)
Four classrooms of two secondary schools located around Lyon in France have been monitored. The objectives are to analyse the quality of the indoor air and the thermal comfort and also the behaviour of the occupants towards opening of the windows. This paper briefly describes the context and the nature of the monitoring campaign, and presents the results of the measurements with direct interpretation of the ventilation needs. Results from this study show that allowable CO{sub 2} levels are overpassed several times in a school day. The presence of a mechanical ventilation system leads to lower peaks but the fresh airflow is too small to prevent an indoor confining, that is also revealed by the aerobiological analysis. (author)
1994-12-31
Vacuum Packaging for Microelectromechanical Systems ...
... more than expected in developing a unique bond strength measurement protocol that is important for a wide range of bond strength measurements. ...
2002-10-01
A unique mechanistic method has been developed at the NASA Glenn Research Center to
2008-01-01
System). From collecting terabytes of video footage to tracking the movements of the submarines, this software is essential to the science team as they explore unique structures on...
2011-09-16
Magnetic Tape Pulse Width to Digital Convertor.
... This is achieved by the use of a unique logic circuit employing a plurality of flip-flop devices, multivibrators and AND gates. ...
1976-12-07
Germinating a New SEAD: The Implications of Executing the ...
... Possessing the unique perspective of space, space-based weapons can immediately ... A weapon system with enough space-based platforms at ...
2001-06-01
ANALYSIS OF BENDING CREEP BEHAVIOR OF SILICON ...
... AT 1170 DEG C. A UNIQUE CREEP CONSTITUTIVE EQUATION CONSISTING OF LINEAR AND POWER LAW TERMS WAS PROPOSED, AND ...
DEFF Research Database (Denmark)
This project analyzes Nordic trends in the development and industrial uptake of green nanotechno-logy in construction. The project applies an evolutionary economic perspective in analyzing the innovation dynamics and firm strategies in the window value chains in three Nordic countries, Denmark, Finland and Sweden. Hence the project investigates two pervasive parallel market trends: The emergence of the green market and the emergence of nanotechnology. The analysis investigates how a traditional economic sector such as the construction sector reacts to such major trends. Conclusions are multiple, but among the most important are: Eco-innovation has become the perhaps most important driver for innovation in the construction sector. Search into eco-innovative business opportunities is intense among all companies along the three analyzed Nordic window chains. While we generally find a low uptake of nanotechnology in the construction sector in the ...
2010-01-01
A desiccant dehumidifier for electric vehicle heating
Energy Technology Data Exchange (ETDEWEB)
Vehicle heating requires a substantial amount of energy. Engines in conventional cars produce enough waste heat to provide comfort heating and defogging/defrosting, even under very extreme conditions. Electric vehicles (EVs), however, generate little waste heat. Using battery energy for heating may consume a substantial fraction of the energy storage capacity, reducing the vehicle range, which is one of the most important parameters in determining EV acceptability. Water vapor generated by the vehicle passengers is in large part responsible for the high heating loads existing in vehicles. In cold climates, the generation of water vapor inside the car may result in water condensation on the windows, diminishing visibility. Two strategies are commonly used to avoid condensation on windows: windows are kept warm, and a large amount of ambient air is introduced in the vehicle. Either strategy results in a substantial heating ...
1996-09-01
International Nuclear Information System (INIS)
We study the uniqueness of solutions of a semilinear elliptic problem obtained from an inverse formulation when the nonlinear terms of the equation are prescribed in a general class of real functions. The inverse problem arises in the modeling of the magnetic confinement of a plasma in a Stellarator device. The uniqueness proof relies on an L"#infinity# -estimate on the solution of an auxiliary nonlocal problem formulated in terms of the relative rearrangement of a datum with respect to the solution.
... It is well camouflaged and each individual has unique back pattern markings. It eats mainly spiders and insects. The Eastern Lined Earless Dragon is a small dragon lizard measuring up to 21cm in length. It is well camouflaged and each individual has unique back ... It is well camouflaged and each individual has unique back pattern markings. It eats mainly spiders and insects. It lives in and around grass tussocks as well as small holes in the ground that are also used by invertebrates such as wolf spiders and crickets....
Limit cycle's uniqueness for second order O.D.E.'s polynomial in $\\dot x$
We prove a uniqueness result for limit cycles of the second order ODE $\\ddot x + \\sum_{j=1}^{J}f_{j}(x)\\dot x^{j} + g(x) = 0$. We extend a uniqueness result proved in \\cite{CRV}. The main tool applied is an extension of Massera theorem proved in \\cite{GS}.
2010-01-01
The pharmacological activity of medical herbs after microbiological decontamination by irradiation
Energy Technology Data Exchange (ETDEWEB)
In the Institute of Nuclear Chemistry and Technology research on microbiological decontamination of medicinal herbs by irradiation has been carried out since 1996. It was shown that using ionizing radiation (a dose of 10 kGy) can obtain satisfactory results of microbiological decontamination of these products. The content of essential biologically active substances such as essential oils, flavonoids, glycosides, anthocyans, antra-compounds, poliphenoloacids, triterpene saponins, oleanosides and plants mucus did not change significantly after irradiation. Pharmacological activity of medicinal herbs has been found satisfactory after microbiological decontamination by irradiation.
2000-03-01
Precise measurements of alpha particle counting efficiencies and mean ranges
International Nuclear Information System (INIS)
Precise measurements of alpha particle counting efficiencies have been made using isotropic, infinitely thin alpha emitting sources placed in direct contact with a thin, end-window, gas flow proportional detector. Except for alpha particle absorption in the window material, this geometry approaches 2#pi#, such that the only other variation in the response of the counter is from the random decay of the source. The data are fitted to the expected linear function of count rate versus window thickness and the resulting fitting parameters are used to calculate the counting efficiencies for a given thickness of window material. Counting efficiencies for 5.31, 6.06, and 8,78 MeV alpha particles have been determined from sources of "2"1"0Po and the progeny of "2"1"2Pb. For the particular counter used, the counting efficiencies in counts per alpha and their respective relative standard deviations were 0.401 #+-# ...
1978-12-01
High bandgap window layer for GaAs solar cells and fabrication process therefor
The specification describes a semiconductor solar cell and fabrication process therefor wherein a thin N-type gallium arsenide layer is deposited on a larger P-type substrate layer which is selected from the group of III-V ternary compounds consisting of aluminum phosphide antimonide, AlPSb, and aluminum indium phosphide, AlInP. P-type impurities are diffused from the substrate layer into a portion of the thin N-type gallium arsenide layer to form P-type region wherein which defines a PN junction in the thin gallium arsenide layer. Thus, the quantity of gallium arsenide required to provide this PN photovoltaic junction layer in the cell is minimized, and th P-type substrate serves as a high bandgap window layer for the cell. Such high bandgap of this window material is especially well suited for efficiently transmitting the blue spectrum of sunlight to the PN junction, thus enhancing the power conversion efficiency of the solar cell.
1979-05-29
Large scintillation cells for high sensitivity radon concentration measurements
Energy Technology Data Exchange (ETDEWEB)
Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alpha source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length without difficulty from ...
1983-07-01
Large scintillation cells for high sensitivity radon concentration measurements
International Nuclear Information System (INIS)
Methods for improving the sensitivity of scintillation cells for radon concentration measurements were studied with emphasis on improving light collection efficiency. This allows the length and hence the volume of the cell to be increased. Variables studied were choice of scintillator material, its method of application and thickness, length of cell, cell material, type and configuration of reflectors, choice of photomultipliers, and factors affecting background. Response from various areas of the cell surface was studied with an alphy source and with radon filling. Coating the window with phosphor was found to be counter-productive. The optimum results obtained were with the inside of the cell (other than the window) covered with a thick layer of ZnS(Ag), or with a thick layer of reflective material coated with a thin layer of phosphor. With it, a 10 cm diameter plexiglass cell can be extended to at least 50 cm length without difficulty from ...
Embedded systems for vacuum control at PEFP
International Nuclear Information System (INIS)
Development of a front end system for a high energy proton accelerator is in progress at Korea Atomic Energy Research Institute (KAERI) for basic science and industrial applications. The proper vacuum components has been installed and operated successfully between ion source and RFQ. The reliable operation of the accelerator has been completed at vacuum system in the high and ultra high vacuum range under operating conditions. Proper control system for the vacuum instruments, based on PC operated by Windows, has been designed and constructed by control group at PAL. As PC operated by windows with inherent instability does not proper, embedded system can be replaced for reliable operation system, such as VME system operated by vxWorks.
2005-05-26
Collisionless driven reconnection in an open system
Energy Technology Data Exchange (ETDEWEB)
Particle simulation studies of collisionless driven reconnection in an open system are presented. Collisionless reconnection evolves in two steps in accordance with the formation of two current layers, i.e., an ion current layer in the early ion phase and an electron current layer in the late electron phase. After the electron current layer is formed inside the ion current layer, the system relaxes gradually to a steady state when convergent plasma flow is driven by an external electric field with a narrow input window. On the other hand, when the convergent plasma flow is driven from the wide input window, magnetic reconnection takes place in an intermittent manner, due to the frequent formation of magnetic islands in the vicinity of neutral sheet. (author)
2000-06-01
Psychological Aspects of Widowhood and Divorce
UK PubMed Central (United Kingdom)
Despite advances in standard of living of the population, the condition of widows and divorced women remains deplorable in society. The situation is worse in developing nations with their unique social,...Full Text Available
2009-01-01
UK PubMed Central (United Kingdom)
A unique case of pachydermoperiostosis, multiple epiphyseal dysplasia, and secondary osteoarthritis is described. An additional interesting feature was the presence of acroosteolysis of the distal phalanges...Full Text Available
1983-02-01
Morphology and function of the forelimb in arboreal frogs: specializations for grasping ability?
UK PubMed Central (United Kingdom)
Frogs are characterized by a unique morphology associated with their saltatory lifestyle. Although variation in the form and function of the pelvic girdle and associated appendicular system related...Full Text Available
2008-09-01
Gene therapy for ocular diseases
UK PubMed Central (United Kingdom)
The eye is an easily accessible, highly compartmentalised and immune-privileged organ that offers unique advantages as a gene therapy target. Significant advancements have been made in understanding...Full Text Available
2011-05-01
Characterization of cry Genes in a Mexican Bacillus thuringiensis Strain Collection
UK PubMed Central (United Kingdom)
Mexico is located in a transition zone between the Nearctic and Neotropical biogeographical regions and contains a rich and unique biodiversity. A total of 496 Bacillus thuringiensis...Full Text Available
1998-12-01
UK PubMed Central (United Kingdom)
BackgroundThe Prospective Space-Time scan statistic (PST) is widely used for the evaluation of space-time clusters of point event data. Usually a window of cylindrical shape is employed,...Full Text Available
Energy Technology Data Exchange (ETDEWEB)
Because of good thermal insulation of advanced energetic buildings and their good airtightness the air hygiene is insufficient. A normal ventilation behaviour by window opening consumes too much heating energy. A calculation method is shown taking into account a required air change number, flow rate and indoor air quality as thermal comfort in the rooms occupied by different number of persons. (GL)
2006-07-01
Noise Shielding Using Acoustic Metamaterials
International Nuclear Information System (INIS)
We exploit theoretically a class of rectangular cylindrical devices for noise shielding by using acoustic metamaterials. The function of noise shielding is justified by both the far-field and near-field full-wave simulations based on the finite element method. The enlargement of equivalent acoustic scattering cross sections is revealed to be the physical mechanism for this function. This work makes it possible to design a window with both noise shielding and air flow. (electromagnetism, optics, acoustics, heat transfer, classical mechanics, and fluid dynamics)
2010-03-15
MOS device chemical response reversal with temperature
British Library Electronic Table of Contents (United Kingdom)
Biased above threshold (VT), pulsed photocurrent (u) measurements on windowed silicon Pd gate MOS capacitors are shifted (DV) negatively by H2/N2, whereas Au gates shift positively under NO2/air. Below VT, the shifts are reversed by adjustments of interface state population. Minor temperature increases may coax the device from inversion to depletion, inducing sign reversal of the chemical response.
2010-01-01
Destabilization of the hot-electron precessional mode in tandem mirrors and bumpy tori
International Nuclear Information System (INIS)
The high-frequency precessional mode of a hot-electron-stabilized magnetic configuration has previously been shown to be stable in a window of core-plasma mass. Under conditions of frequency matching, the resulting stable negative-energy precessional wave can be destabilized by coupling to positive-energy shear-Alfven waves. Coupling is avoided when the hot-electron precession frequency exceeds the core-plasma ion gyrofrequency.
An emulation and management software for MCA with 64 independent coded inputs
International Nuclear Information System (INIS)
A Software for the Neutron Scattering time-of-flight Spectrometer with 64 independent coded inputs is preset. It performs data acquirement and management. The work platform of the software is the Windows 98 and programmed with Visual Basic 6.0. It supports 64 x 1024 channel analyzer computer system. The friendly interface, convenient operation and high reliability are advantages of the Software
2000-09-07
The Silicone Conundrum Part II: ?Low Outgassing? Silicones
British Library Electronic Table of Contents (United Kingdom)
Silicones have many desirable properties and as a result are incorporated into a wide range of products. However, they present unique problems that result from their propensity to outgas resulting in residue formation at unexpected places. Hence, the silicone conundrum?when to use these materials and when to beware of potential pitfalls. In this article, an outgassing mechanism unique to ?low outgassing? silicones is discussed. Examples are given where this has led to failures and remediation steps are highlighted.
2011-01-01
Clinical helical tomotherapy commissioning dosimetry
International Nuclear Information System (INIS)
Helical tomotherapy presented many unique dosimetric challenges and solutions during the initial commissioning process, and some of them are presented. The dose calculation algorithm is convolution/superposition based. This requires that the energy fluence spectrum and magnitude be quantified. The methodology for doing so is described. Aspects of the energy fluence characterization that are unique to tomotherapy are highlighted. Many beam characteristics can be measured automatically by an included megavoltage computed tomography imaging system. This greatly improves data collection efficiency.
2003-12-01
Uniqueness from pointwise observations in a multi-parameter inverse problem
In this paper, we prove a uniqueness result in the inverse problem of determining several non-constant coefficients of one-dimensional reaction-diffusion equations. Such reaction-diffusion equations include the classical model of Kolmogorov, Petrovsky and Piskunov as well as more sophisticated models from biology. When the reaction term contains an unknown polynomial part of degree $N,$ with non-constant coefficients $\\mu_k(x),$ our result gives a sufficient condition for the uniqueness of the determination of this polynomial part. This sufficient condition only involves pointwise measurements of the solution $u$ of the reaction-diffusion equation and of its spatial derivative $\\partial u / \\partial x$ at a single point $x_0,$ during a time interval $(0,\\epsilon).$ In addition to this uniqueness result, we give several counter-examples to uniqueness, which emphasize the optimality of our ...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
The relationship between the gas to melt ratio (GMR) and the surface temperature of an evolving billet surface in spray forming is investigated numerically. The basis for the analysis is an integrated approach for modelling the entire spray forming process. This model includes the droplet atomization taking thermal coupling into consideration and the deposition of material at the surface of the billet taking geometrical aspects such as shading into account. The coupling between these two models is accomplished by ensuring that the total droplet size distribution of the spray is the summation of ''local'' droplet size distributions along the r-axis of the spray cone. The criterion for a successful process has been a predefined process window characterised by a desired fraction solid range at a certain distance from the atomizer. Inside this process window, the gas and melt flows have been varied and the ...
2005-06-01
Energy Technology Data Exchange (ETDEWEB)
Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} thin films were successfully prepared by the solution deposition using lithium acetate, aluminum nitrate, ammonium dihydrogen phosphate and titanium butoxide as starting materials. The structure, surface morphology, electrochemical window, and ionic conductivity of the films were studied by X-ray diffraction, scanning electron microscopy, cyclic voltammetry and AC impedance. The results showed that Li{sub 1.3}Al{sub 0.3}Ti{sub 1.7}(PO{sub 4}){sub 3} thin films annealed between 750 deg. C and 900 deg. C prepared by this method were well crystallized, homogenous and crack-free. The electrochemical window was beyond 2.4 V and the ionic conductivity was approximately 1.57x10{sup -5} S/cm at room temperature for the film annealed at 800 deg. C for 30 min.
2003-02-03
International Nuclear Information System (INIS)
Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films were successfully prepared by the solution deposition using lithium acetate, aluminum nitrate, ammonium dihydrogen phosphate and titanium butoxide as starting materials. The structure, surface morphology, electrochemical window, and ionic conductivity of the films were studied by X-ray diffraction, scanning electron microscopy, cyclic voltammetry and AC impedance. The results showed that Li_1_._3Al_0_._3Ti_1_._7(PO_4)_3 thin films annealed between 750 deg. C and 900 deg. C prepared by this method were well crystallized, homogenous and crack-free. The electrochemical window was beyond 2.4 V and the ionic conductivity was approximately 1.57x10"-"5 S/cm at room temperature for the film annealed at 800 deg. C for 30 min.
2003-02-03
OPC Server and BridgeView Application for High Voltage Power Supply Lecroy 1458
Abstract The aim of this project was to develop an OPC server to communicate over an RS232 serial line. This communication media is commonly used with commercial instruments. The development was made for a High Voltage power supply in the context of the Alice [1] experiment. In addition, the structured modular concept will allow changing the transmission media or power supply type with little effort. The high voltage power supply should be accessible remotely through a network. OPC[2] is an acronym for OLE[3] for Process Control. OPC is based on the DCOM [3] communication protocol, which allows communication with any computer running a Windows based OS. This standard is widely used in industry to access device data through Windows applications. The concept is based on the client-server architecture. The hardware and the software architecture are described. Subsequently details of the implemented programs are given with emphasis on the ...
2000-01-01
Microclimatic conditions at the external surface of building envelopes
Energy Technology Data Exchange (ETDEWEB)
The project is described, the motivation for the research and the microclimate is defined in relation to both building physics research and applications. Air temperatur, air humidity, solar radiation and air velocity are briefly considered, whilst driving rain and long-wave radiation are described in more detail. Convective heat transfer and surface coefficients are discussed, although they are not microclimatic factors, merely resulting from combinations of such factors. They are included as they are important in relation to transfer of heat and moisture at the surface of the building envelope. Driving rain measurement is the main area of interest, including development of measurement equipment. Long-wave irradiation is measured and compared with empirical formulae from the literature. Window convection heat transfer is another main area of interest. Nocturnal convective heat transfer from a double pane glazing is studied and measurement principles are discussed. ...
1998-12-31
Measuring characteristics on emissivity using infrared thermometer for RCCS
International Nuclear Information System (INIS)
In VHTGR (Very High Temperature Gas-cooled Reactor), the radiation plays an important role in heat transfer through the cavity in RCCS (Reactor Cavity Cooling System). We performed the series of experiments to measure the emissivity using the infrared thermometer with wavelength range of 8#approx#14 #mu#m. As the first step, the transmittance of Zinc Selenide (ZnSe) window was measured to estimate the emissivity that can compensate the attenuation effect of window. The kind of gas with various concentrations in the cavity will be released during postulated accidents to the coolant type, so it is essential to estimate the effects of gas on the measurement of emissivity. In this manner we measured the emissivity with the air, the helium and the steam inside chamber. The results represent that the concentration of the air and the helium do not affect the emissivity significantly while the steam decreases the measured emissivity relatively. It ...
2004-12-01
Investigation of the impact of electricity rate and mix on optimum green building design
Energy Technology Data Exchange (ETDEWEB)
The basic principle of the green building philosophy is to design buildings that consider environmental performance. Residential and commercial buildings in Canada consume about 30 per cent of the total secondary energy use and are responsible for approximately 29 per cent of carbon dioxide equivalent greenhouse gas emissions and many other wastes. An optimization model was developed which minimizes life cycle cost and life cycle environmental impact. The model distinguishes different energy sources and incorporates their impacts, such as resource depletion, global warming and acidification. The model also considers design variables such as window type, orientation, building orientation, window-to-wall ratio, wall type and roof type. The model can be used to identify optimum green building designs for given conditions. The model uses expanded cumulative exergy consumption as the indicator for life cycle environmental performance. As such, it ...
2004-07-01
Gear fault detection using customized multiwavelet lifting schemes
Fault symptoms of running gearboxes must be detected as early as possible to avoid serious accidents. Diverse advanced methods are developed for this challenging task. However, for multiwavelet transforms, the fixed basis functions independent of the input dynamic response signals will possibly reduce the accuracy of fault diagnosis. Meanwhile, for multiwavelet denoising technique, the universal threshold denoising tends to overkill important but weak features in gear fault diagnosis. To overcome the shortcoming, a novel method incorporating customized (i.e., signal-based) multiwavelet lifting schemes with sliding window denoising is proposed in this paper. On the basis of Hermite spline interpolation, various vector prediction and update operators with the desirable properties of biorthogonality, symmetry, short support and vanishing moments are constructed. The customized lifting-based multiwavelets for feature matching are chosen by the minimum entropy ...
2010-07-01
GUIDE : Unifying Evolutionary Engines through a Graphical User Interface
Many kinds of Evolutionary Algorithms (EAs) have been described in the literature since the last 30 years. However, though most of them share a common structure, no existing software package allows the user to actually shift from one model to another by simply changing a few parameters, e.g. in a single window of a Graphical User Interface. This paper presents GUIDE, a Graphical User Interface for DREAM Experiments that, among other user-friendly features, unifies all kinds of EAs into a single panel, as far as evolution parameters are concerned. Such a window can be used either to ask for one of the well known ready-to-use algorithms, or to very easily explore new combinations that have not yet been studied. Another advantage of grouping all necessary elements to describe virtually all kinds of EAs is that it creates a fantastic pedagogic tool to teach EAs to students and newcomers to the field.
2003-01-01
Dynamic interpretation of organic-matter maturation and evolution of oil-generative window
Energy Technology Data Exchange (ETDEWEB)
Two phases are recognized in the maturation of organic matter and evolution of the oil-generative window (OGW): (a) a basinal subsidence phase during which potential source rocks undergo burial through a static initial OGW, and maturation is due essentially to increasing temperature with depth, and (b) a postsubsidence phase during which the OGW moves vertically upward through the static sedimentary fill, and maturation is due to time effects. Only the final shallow position of OGW can be defined by geochemical indices of maturity. The hydrocarbon generation sequence progresses from bottom to top, beginning with the lighter hydrocarbons (or even thermogenic gas) at the initial OGW at depth, followed by progressively heavier hydrocarbons as the OGW moves vertically upward. This dynamic model of hydrocarbon generation permits modeling of past positions of OGW relative to basin evolution through interpretation of oil-genesis nomographs. It also provides genetic ...
1984-08-01
Authentication via wireless networks
Personal authentication is an important process we encounter almost every day; when we are logging on a computer, entering a company where we work, or a restricted area, when we are using our plastic credit cards to pay for a service or to complete some other financial transaction, etc. In each of these processes of personal authentication some kind of magnetic or optical token is required. But by using novel technologies like mobile computing and wireless networking, it is possible to avoid carrying multitude of ID cards or remembering a number of PIN codes. Article shows how to efficiently authenticate users via Personal Area Networks (PAN) like Bluetooth or IrDA using commonplace AES (Rijndel) or MD5 encryption. This method can be implemented on many types of mobile devices like Pocket PC PDA with Windows CE (Windows Mobile 2003) real-time operating system, or any other customized OS, so we will explain all components and key features of ...
2007-01-01
Unique health care utilization patterns in a homeless population in Ghent
UK PubMed Central (United Kingdom)
BackgroundExisting studies concerning the health care use of homeless people describe higher utilisation rates for hospital-based care and emergency care, and lower rates for primary...Full Text Available
UK PubMed Central (United Kingdom)
Borna disease virus (BDV) uses a unique strategy of replication and transcription which takes place in the nucleus, unlike other known, nonsegmented, negative-stranded RNA viruses of animal origin....Full Text Available
1998-12-01
The reactivity of thiol groups and the subunit structure of aldolase
UK PubMed Central (United Kingdom)
1. Seven unique carboxymethylcysteine-containing peptides have been isolated from tryptic digests of rabbit muscle aldolase carboxymethylated with iodo[2-14C]acetic acid in 8m-urea....Full Text Available
1970-04-01
Experimental results are presented for a new and unique heat transfer augmentation technique in tubes. The technique consists of inserting a porous mesh structure into the flow passage of the tube. Due to the increased degree of turbulence, both the singl...
1970-01-01
UK PubMed Central (United Kingdom)
BackgroundThe National Consortium for Multicultural Education for Health Professionals (Consortium) comprises educators representing 18 US medical schools, funded by the National...Full Text Available
2010-05-01
Superior energy capacity of graphene nanosheets for a nonaqueous lithium-oxygen battery.
Graphene nanosheets (GNSs) were synthesized and used as cathode active materials in a nonaqueous lithium-oxygen battery. The GNSs electrode delivered an extremely high discharge capacity in comparison to carbon powders, which is attributed to its unique morphology and structure. PMID:21779551
2011-07-21
Superheavy elements - the quest in perspective
International Nuclear Information System (INIS)
A review is presented of the quest for superheavy elements under the following headings - early history; physical and nuclear properties unique to superheavy elements; searches in nature; terrestrial samples; extra-terrestrial samples; and searches at accelerators. 72 references. (U.K.).
Semiclassical aspects of transfer reactions
Semiclassical analysis of heavy ion induced transfer reactions are discussed for the quasielastic region. Some unique aspects of these reactions are shown, the variety of features which can be understood semiclassically is demonstrated, and some open problems are indicated. 28 refs., 16 figs. (LEW)
1985-01-01
UK PubMed Central (United Kingdom)
Hibernators are unique among mammals in their ability to survive extended periods of time with core body temperatures near freezing and with dramatically reduced heart, respiratory, and metabolic rates...Full Text Available
2010-02-01
Retinal Fundus Image Registration via Vascular Structure Graph Matching
UK PubMed Central (United Kingdom)
Motivated by the observation that a retinal fundus image may contain some unique geometric structures within its vascular trees which can be utilized for feature matching, in this paper, we proposed...Full Text Available
2010-01-01
Relation of the One-Phase Stefan Problem to the Seepage of Liquids and Electrochemical Machining.
The flow of water through a dam of fairly arbitrary shape is examined in the limit of large frictional drag on the flow. The relation of the problem to the one-phase Stefan problem and a problem of anodic smoothing is explored. Monotonicity and uniqueness...
1979-01-01
Recent Applications of DNA Microarray Technology to Toxicology and Ecotoxicology
UK PubMed Central (United Kingdom)
Gene expression is a unique way of characterizing how cells and organisms adapt to changes in the external environment. The measurements of gene expression levels upon exposure to a chemical can be...Full Text Available
2006-01-01
Potential of plant genetic systems for monitoring and screening mutagens
UK PubMed Central (United Kingdom)
Plants have too long been ignored as useful screening and monitoring systems of environmental mutagens. However, there are about a dozen reliable, some even unique, plant genetic systems that can increase...Full Text Available
1978-12-01
Physical and optical properties of rare earth cobalt magnets
Energy Technology Data Exchange (ETDEWEB)
Rare Earth Cobalt (REC) permanent magnets have unique properties that permit solutions to some optical tasks that cannot be accomplished with conventional magnets. A review of design and of performance characteristics of these magnets includes an analytical description of the three dimensional fringe fields of REC quadrupoles.
1980-08-01
Overcoming the challenges of membrane protein crystallography
UK PubMed Central (United Kingdom)
Membrane protein structural biology is still a largely unconquered area, given that approximately 25% of all proteins are membrane proteins and yet less than 150 unique structures are available. Membrane...Full Text Available
2008-10-01
National Institutes of Health (NIH) Health Matters Podcasts
60 http://www.nih.gov/news/radio/healthmatters/index.htm 60-second Health Matters spots-one unique health report for each weekday of the month. en-us 2010 Mon, 01 Feb 2010 12:00:00...
2011-08-26
UK PubMed Central (United Kingdom)
Vulnerability to abused drugs is influenced by multiple genes unique to each drug as well as to risk genes for polydrug abuse. If several inbred mouse strains respond to different drugs similarly,...Full Text Available
2008-11-01
Monovalent and unpoised status of most genes in undifferentiated cell-enriched Drosophila testis
UK PubMed Central (United Kingdom)
BackgroundIncreasing evidence demonstrates that stem cells maintain their identities by a unique transcription network and chromatin structure. Opposing epigenetic modifications...Full Text Available
2010-01-01
Molecular characterization of a unique retrovirus associated with a fish tumor.
UK PubMed Central (United Kingdom)
The walleye dermal sarcoma is a mesenchymal tumor which seasonally affects up to 27% of adult walleye fish (Stizostedion vitreum). It arises multicentrically in the dermis, in which its development...Full Text Available
1992-01-01
UK PubMed Central (United Kingdom)
The goal of this study was to determine if the exaggerated morphine-induced conditioned place preference (CPP) response seen in adult rats after preweanling methylphenidate exposure is unique...Full Text Available
2009-03-01
Infravesical obstruction due to benign intraurethral prostatic cyst.
UK PubMed Central (United Kingdom)
We report a case of symptomatic intraurethral prostatic cyst in a 42-yr-old man without clinical evidence of benign prostatic hyperplasia. The intraurethral cyst makes it unique from the all previously...Full Text Available
2003-02-01
UK PubMed Central (United Kingdom)
A unique antibacterial peptide derivative found in immune honeybee lymph, apidaecin 1b (AP1), was randomly mutagenized and characterized by a newly established system to analyze in vivo its structure-function...Full Text Available
1994-10-01
Identification and Characterization of Novel MicroRNAs from Schistosoma japonicum
UK PubMed Central (United Kingdom)
BackgroundSchistosomiasis japonica remains a major public health problem in China. Its pathogen, Schistosoma japonicum has a complex life cycle and a unique repertoire...Full Text Available
UK PubMed Central (United Kingdom)
The supramammillary nucleus (SuM) provides substantial projections to the hippocampal formation. This hypothalamic structure is involved in the regulation of hippocampal theta rhythm and therefore...Full Text Available
2010-09-01
Explosives detection The problem and prospects
Energy Technology Data Exchange (ETDEWEB)
Explosives molecules have a number of unique properties. These properties are discussed. They include low vapor pressures, electronegativity, ''stickiness,'' frangibility, and thermal instability. The program for developing an advanced explosives detector is described.
1984-07-01
Evidence for modular evolution in a long-tailed pterosaur with a pterodactyloid skull
UK PubMed Central (United Kingdom)
The fossil record is a unique source of evidence for important evolutionary phenomena such as transitions between major clades. Frustratingly, relevant fossils are still comparatively rare, most transitions...Full Text Available
2010-02-07
Evaluation of 13C isotopic tracers for metabolic flux analysis in mammalian cells
UK PubMed Central (United Kingdom)
13C metabolic flux analysis (MFA) is the most comprehensive means of characterizing cellular metabolic states. Uniquely labeled isotopic tracers enable more focused analyses to probe...Full Text Available
2009-11-01
Diversity of Microbial Sialic Acid Metabolism
UK PubMed Central (United Kingdom)
Sialic acids are structurally unique nine-carbon keto sugars occupying the interface between the host and commensal or pathogenic microorganisms. An important function of host sialic acid is to regulate...Full Text Available
2004-03-01
UK PubMed Central (United Kingdom)
Malate synthase (EC 4.1.3.2), an enzyme unique to the glyoxylate cycle, was purified to homogeneity from cotyledons of 72-hours, darkgrown cotton (Gossypium hirsutum L.) seedlings....Full Text Available
1987-08-01
Chromosome location of Oryza sativa recombination linkage groups.
UK PubMed Central (United Kingdom)
In situ hybridization, a powerful tool for the molecular cytogeneticist, can be used to physically map repetitive, low-copy, and unique DNA sequences in plant chromosomes. With the availability of a...Full Text Available
1992-09-15
UK PubMed Central (United Kingdom)
The authors' laboratory, using histochemicalmethods, previously identified two types of cholesterol-containing lipid particles in the extracellular spaces of human atherosclerotic lesions, one particle...Full Text Available
1990-01-01
Cavity detection by the electric method: the 3-dimensional case
Energy Technology Data Exchange (ETDEWEB)
In this paper the authors prove a uniqueness theorem for the electric detection of cavities in a three dimensional solid from Cauchy data measured on the surface. The cavities, finite in number, are assumed to be insulating. The surfaces of the cavities are assumed to be smooth on the complement of a set that is, in some sense, negligible. (orig.)
2004-02-01
UK PubMed Central (United Kingdom)
Certain pathogenic species of Bacillus and Clostridium have developed unique methods for intoxicating cells that employ the classic enzymatic “A-B” paradigm for protein toxins. The binary...Full Text Available
2004-09-01
Association of Unique, Isolated Treponemes with Bovine Digital Dermatitis Lesions?
UK PubMed Central (United Kingdom)
This study used a PCR-based approach targeting 16S rRNA gene fragments to determine the occurrence and association of the three bovine digital dermatitis (BDD) treponeme phylogroups within lesions found...Full Text Available
2009-03-01
Ventilation concept, indoor air quality and measurement results in the ``Passivhaus Kranichstein``
Energy Technology Data Exchange (ETDEWEB)
The ``Passivhaus Darmstadt-Kranichstein`` is a 4 unit terrace house with an extremely low total annual energy consumption of less than 32 kWh/m{sup 2} of living area, thereof about 12 kWh are needed for room heating. The determining factors for the low consumption are the superinsulation, airtightness of the thermal envelope in combination with a highly efficient VAV ventilation system, and an improved window construction. The results of a detailed monitoring program allow decisive statements concerning reduction of energy consumption, relief of environment, indoor air quality, and thermal comfort. (author)
1994-12-31
Energy Technology Data Exchange (ETDEWEB)
This short article discusses the results of a market survey on ventilation systems for residential buildings and the role played by ventilation systems in our daily lives. Problems incurred as a result of insufficient ventilation conditions such as the formation of mould in dwellings whose windows have been replaced with better seals are discussed, for example. The negative image of air-conditioning and its causes are examined. The need for action in this area is stressed. Further findings of the study are presented, including a detailed review of current equipment and scenarios on how these systems can develop in the future. The extension of the study to cover the situation in further European countries is mentioned.
2003-07-01
International Nuclear Information System (INIS)
This paper discusses essentially the role of WDXRFS based multi element data in uranium exploration, with special reference to India. The state of art MagiX-PRO WDXRFS with 4 kW end window x-ray tubes has been used in the present study as an indispensable geo-analytical tool for the analysis of major and selected trace elements at ppm to percentage level, with high precision and relatively better accuracy
2010-10-01
Results from a Bragg Curve Spectrometer
Energy Technology Data Exchange (ETDEWEB)
The Bragg Curve Spectrometer (BCS) is an ionization chamber long enough to stop particles of interest. Particles enter through the cathode window and leave an ionization track parallel to the electric field. The ionization electrons drift through a Frisch grid and are collected on an anode. The anode current, as a function of time, is split and used as input for two amplifiers, one with a long integration time constant for energy measurement, and one with a short time constant to pick off the maximum ionization or Bragg peak. The Bragg peak, which is proportional to the nuclear charge, is used for particle identification. We have constructed and tested several versions of the BCS. The results are described.
1984-01-01
Results from a Bragg Curve Spectrometer
International Nuclear Information System (INIS)
The Bragg Curve Spectrometer (BCS) is an ionization chamber long enough to stop particles of interest. Particles enter through the cathode window and leave an ionization track parallel to the electric field. The ionization electrons drift through a Frisch grid and are collected on an anode. The anode current, as a function of time, is split and used as input for two amplifiers, one with a long integration time constant for energy measurement, and one with a short time constant to pick off the maximum ionization or Bragg peak. The Bragg peak, which is proportional to the nuclear charge, is used for particle identification. We have constructed and tested several versions of the BCS. The results are described.
1984-10-22
REQUIREMENTS AND GUIDELINES FOR NSLS EXPERIMENTAL BEAM LINE VACUUM SYSTEMS-REVISION B.
Energy Technology Data Exchange (ETDEWEB)
Typical beam lines are comprised of an assembly of vacuum valves and shutters referred to as a ''front end'', optical elements to monochromatize, focus and split the photon beam, and an experimental area where a target sample is placed into the photon beam and data from the interaction is detected and recorded. Windows are used to separate sections of beam lines that are not compatible with storage ring ultra high vacuum. Some experimental beam lines share a common vacuum with storage rings. Sections of beam lines are only allowed to vent up to atmospheric pressure using pure nitrogen gas after a vacuum barrier is established to protect ring vacuum. The front end may only be bled up when there is no current in the machine. This is especially true on the VUV storage ring where for most experiments, windows are not used. For the shorter wavelength, more energetic photons of the x-ray ring, beryllium ...
1999-05-01
Probing of the Higgs-fermion coupling at. gamma. gamma. -colliders
Energy Technology Data Exchange (ETDEWEB)
Three possibilities to observe the Higgs-top interaction at future {gamma}{gamma}-colliders are discussed: (a) associated Higss production via the {gamma}{gamma}{yields}tanti tH reaction, (b) Higgs obliged radiative correction to the {gamma}{gamma}{yields}tanti t channel, (c) Higgs resonance production via {gamma}{gamma}{yields}H{yields}ZZ. The results obtained show windows of the Higss mass where the Yukawa interaction of the Higss with the top quark can be studied at {gamma}{gamma}-colliders. (orig.).
1992-11-01
Probing of the Higgs-fermion coupling at #gamma##gamma#-colliders
International Nuclear Information System (INIS)
Three possibilities to observe the Higgs-top interaction at future #gamma##gamma#-colliders are discussed: a) associated Higss production via the #gamma##gamma##->#tanti tH reaction, b) Higgs obliged radiative correction to the #gamma##gamma##->#tanti t channel, c) Higgs resonance production via #gamma##gamma##->#H#->#ZZ. The results obtained show windows of the Higss mass where the Yukawa interaction of the Higss with the top quark can be studied at #gamma##gamma#-colliders. (orig.).
Microwave heating type evaporator
Energy Technology Data Exchange (ETDEWEB)
Purpose: To prevent evaporization stills against corrosion due to radioactive liquid wastes. Constitution: Microwaves are supplied from a microwave generator by way of a wave guide tube and through a microwave permeation window to the inside of an evaporatization still. A matching device is attached to the wave guide tube for transmitting the microwaves in order to match the impedance. When the microwaves are supplied to the inside of the evaporization still, radioactive liquid wastes supplied from a liquid feed port by way of a spray tower to the inside of the evaporization still is heated and evaporated by the induction heating of the microwaves. (Seki, T.).
1987-01-22
Interpolation theory and influence of boundary conditions on room air diffusion
Energy Technology Data Exchange (ETDEWEB)
This paper analyses the errors caused by interpolation from existing cases for assessing indoor air flow, air quality and thermal comfort in an office. A sensitivity study is then provided to determine the influence of several boundary conditions on indoor air diffusion. The research is conducted numerically by using a low-Reynolds-number k-{epsilon} model. It can be concluded that the interpolation errors caused by the variations of solar radiation, window size, heat source location due to lighting, and the surface temperatures of interior walls are small and can be quantitatively determined. But it is difficult to estimate the errors introduced by the variations of furniture location and size. (author).
1991-01-01
Integrity assessment of pressure tubes for Wolsung unit 2
Energy Technology Data Exchange (ETDEWEB)
To improve operational safety of the fuel channel for Wolsung units the recommended primary heat transport system (PHTS) operating guidelines were developed, which provides a safe operation window in terms of pressure and temperature to maintain fuel channel integrity, which is similar to pressure-temperature curves used for primary pressure boundary integrity in PWRs and deterministic Leak-Before Break (LBB) analyses were conducted using recent understanding of delayed hydride cracking (DHC) mechanism. In addition, a comparative assessment of LBB analysis was made using the procedures of Fitness For Service Guidelines(FFSG) for pressure tubes rev. 0 and rev. 1.
1997-10-01
Energy Technology Data Exchange (ETDEWEB)
Optimum conditions for microstructural control in industrial hot working of cast and homogenized AZ31 magnesium alloys are evaluated by using a processing map. The recommended window for bulk metal working of this alloy is the domain in the temperature range 300-450 C and strain rate range 1-10 s{sup -1}, and the optimum processing parameters are 400 C and 10 s{sup -1}, where grain-boundary self diffusion is the rate-controlling mechanism. (Abstract Copyright [2009], Wiley Periodicals, Inc.)
2009-03-15
Development of an injection molding tool for complex microfluidic geometries
British Library Electronic Table of Contents (United Kingdom)
This paper will track the design and results of an injection molding tool developed to manufacture microfluidic chips. The mold design and injection molding process was complicated by the presence of integrated capillary fluidic interconnects. We determined that design of the runner and gate system responsible for delivering molten plastic to the cavity had a significant impact on the quality of parts produced by the mold and the size of the process window. Numerical results confirm our findings that reducing gate lengths and increasing part thickness dramatically improved the filling profile and lowered injection pressures by 37%. Finally, the influence of gate location on part shrinkage is analyzed and discussed.
2011-01-01
CaSnO3:. a high capacity anode material for Li-ion batteries
Calcium stannate (CaSnO3) powders with the distorted perovskite structure have been synthesized by solid state and the sol-gel methods and their electrochemical performance was compared. The sol-gel CaSnO3 shows stable cycling performance with a reversible capacity of 430-440 mAh/g (0.005-1.0 V; 60 mA/g) up to 50 cycles. The role of preparatory conditions, morphology and cycling conditions (current density and potential window) on the anodic performance of the compounds are addressed.
2002-12-01
Beginning PHP, Apache, MySQL web development
An ideal introduction to the entire process of setting up a Web site using PHP (a scripting language), MySQL (a database management system), and Apache (a Web server)* Programmers will be up and running in no time, whether they're using Linux or Windows servers* Shows readers step by step how to create several Web sites that share common themes, enabling readers to use these examples in real-world projects* Invaluable reading for even the experienced programmer whose current site has outgrown the traditional static structure and who is looking for a way to upgrade to a more efficient, user-f
2004-01-01
A study on the reduction of indoor radon contamination
Energy Technology Data Exchange (ETDEWEB)
The purpose of the present study is to find ways to reduce the quantity of indoor radon contamination. The study was done from July, 2005 until December, 2005. It was found out that the easiest and most effective way to do that is to open the windows as often as possible and let the indoor air flow outside. When it is not possible to ventilate a room, the indoor radon contamination quantity can reduced by providing activated charcoal in the room. It has been proved that activated charcoal can absorb the room in the air. We need more activated charcoal in proportion to the size of the room. A further research is needed to investigate the amount of activated charcoal that will work most effectively.
2006-06-15
A database for QA/QC in neutron activation analysis and gamma-ray spectrometry
International Nuclear Information System (INIS)
A database has been designed for storing, retrieving and analyzing information about samples, experimental conditions and results obtained by neutron activation analysis and gamma-ray spectrometry. It has been created using Microsoft ACCESS 2002 under a Windows operating system. The database has been designed not only for saving information but also for quality assurance and quality control purposes. The structure of the relational design has been discussed and demonstrated with a new graphical feature of ACCESS 2002 called PIVOTCHART. (author)
2007-04-01
The newborn infant: a missing stage in developmental psychology
British Library Electronic Table of Contents (United Kingdom)
Abstract Although neonatology, the study of the newborn, is well established in medical science, psychological research on the newborn is relatively scarce. Can we justify this period as a distinct stage of human development in Psychology? This introductory article considers the unique characteristics of the neonatal period, the impact of the transition to extrauterine life, including the impact of birth itself, and the stages of brain development that characterize this period. It presents evidence of an intentional, intersubjective neonate, and uses behavioural and neuroscientific evidence to argue that the neonate's early social preferences and responses indicate a unique, sensitive, experience-expectant stage of development. The authors of this issue agree in proposing that the newborn ...
2011-01-01
Human experience with an endoluminal, endoscopic, gastrojejunal bypass sleeve
British Library Electronic Table of Contents (United Kingdom)
Background This report describes the authors? experience with a unique endoluminal, endoscopically delivered and retrieved gastroduodenojejunal bypass sleeve, including short-term weight loss and changes in comorbidities. Methods A prospective, single-center trial was designed. The patients were morbidly obese individuals who met the National Institutes of Health criteria for bariatric surgery. The device used was a unique gastroduodenojejunal bypass sleeve secured at the esophagogastric junction with endoscopic and laparoscopic techniques and designed to create an endoluminal gastroduodenojejunal bypass. At completion of the trial, the device was explanted with endoscopic retrieval. The primary end points were safety and incidence of adverse events. The secondary outcomes included the per...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
The DOETRAN model is a DSM database manager, developed to act as an intermediary between the whole building energy simulation model, DOE-2, and the DBEDT DSM Forecasting Model. DOETRAN accepts output data from DOE-2 and TRANslates that into the format required by the forecasting model. DOETRAN operates in the Windows environment and was developed using the relational database management software, Paradox 5.0 for Windows. It is not necessary to have any knowledge of Paradox to use DOETRAN. DOETRAN utilizes the powerful database manager capabilities of Paradox through a series of customized user-friendly windows displaying buttons and menus with simple and clear functions. The DOETRAN model performs three basic functions, with an optional fourth. The first function is to configure the user`s computer for DOETRAN. The second function is to import DOE-2 files with energy and loadshape data for each building type. The third main ...
1995-04-01
Equivalent dose estimation using a single aliquot of polymineral fine grains
International Nuclear Information System (INIS)
We have tested the suitability of a new single-aliquot regenerative-dose protocol for estimating the equivalent dose (D_e) in polymineral fine grains extracted from colluvia from various sites in Germany. First, we report the behaviour of three OSL signals: (i) blue-stimulated, (ii) infrared-stimulated luminescence, and (iii) blue-stimulated luminescence following infrared (IR) stimulation, using a near-UV (290-380 nm) detection window in each case. For these three signals, there is a significant change in sensitivity with regeneration cycle; this change can be compensated for using the response to a fixed test dose after each natural or regenerated measurement. The source of the three luminescence signals is then investigated using pulse-anneal and elevated-temperature experiments. Fading tests on laboratory-induced signals show that although the IR signals fade by up to 23% in 15 days at 100 deg. C, the post-IR blue signals are stable. The preheat dependence of ...
2001-02-01
Energy Technology Data Exchange (ETDEWEB)
Two window layer materials, Al{sub 0.51}In{sub 0.49}P (E{sub g} = 2.3 eV) and Ga{sub 0.51}In{sub 0.49}P (E{sub g} = 1.88 eV) were compared for gas-source and solid-source MBE grown GaAs and Ga{sub 0.84}In{sub 0.16}As{sub 0.68}P{sub 0.32} (E{sub g} = 1.55 eV) solar cells. Due to the wider band-gap of Al{sub 0.51}In{sub 0.49}P, the increased spectral response was observed for both GaAs and Ga{sub 0.84}In{sub 0.16}As{sub 0.68}P{sub 0.32} material based solar cells. In the case of the GaAs cells, the short-circuit current density was observed to increase from 32.5 mA/cm{sup 2} to 34.4 mA/cm{sup 2} with the Al{sub 0.51}In{sub 0.49}P window layer at AM0. Similar improvement was observed for the Ga{sub 0.84}In{sub 0.16}As{sub 0.68}P{sub 0.32} solar cells.
1997-12-31
Willingness to pay for energy-saving measures in residential buildings
Energy Technology Data Exchange (ETDEWEB)
This paper uses a choice experiment to evaluate the consumers' willingness to pay for energy-saving measures in Switzerland's residential buildings. These measures include air renewal (ventilation) systems and insulation of windows and facades. Two groups of respondents consisting respectively of 163 apartment tenants and 142 house owners were asked to choose between their housing status quo and each one of the several hypothetical situations with different attributes and prices. The estimation method is based on a fixed-effects logit model. The results suggest that the benefits of the energy-saving attributes are significantly valued by the consumers. These benefits include both individual energy savings and environmental benefits as well as comfort benefits namely, thermal comfort, air quality and noise protection. (author)
2008-03-15
VIPEX (Vital-area Identification Package EXpert) Software Verification and Validation
International Nuclear Information System (INIS)
The purposes of this report are (1) to perform a Verification and Validation (V and V) test for the VIPEX(Vital-area Identification Package EXpert) software and (2) to improve a software quality through the V and V test. The VIPEX was developed in Korea Atomic Energy Research Institute (KAERI) for the Vital Area Identification (VAI) of nuclear power plants. The version of the VIPEX which was distributed is 3.2.0.0. The VIPEX was revised based on the first V and V test and the second V and V test was performed. We have performed the following tasks for the V and V test on Windows XP and VISTA operating systems: ? Testing basic functions including fault tree editing ? Testing all kind of functions ? Research for update from Visual BASIC 6.0 to Visual BASIC 2008
2003-12-01
The fraction of substitutional boron in silicon during ion implantation and thermal annealing
Energy Technology Data Exchange (ETDEWEB)
We present results from a kinetic Monte Carlo simulation of boron transient enhanced diffusion (TED) in silicon. Our approach avoids the use of phenomenological fits to experimental data by using a complete and self-consistent set of values for defect and dopant energetics derived mostly from {ital ab initio} calculations. The results predict that, during annealing of 40 keV B-implanted Si at 800{degree}C, there exists a time window during which all the implanted boron atoms are substitutional. At earlier or later times, the interactions between free silicon self-interstitials and boron atoms drive the growth of boron clusters and result in an inactive boron fraction. The results show that the majority of boron TED takes place during the growth period of interstitial clusters and not during their dissolution. {copyright} {ital 1998 American Institute of Physics.}
1998-05-01
The fraction of substitutional boron in silicon during ion implantation and thermal annealing
International Nuclear Information System (INIS)
We present results from a kinetic Monte Carlo simulation of boron transient enhanced diffusion (TED) in silicon. Our approach avoids the use of phenomenological fits to experimental data by using a complete and self-consistent set of values for defect and dopant energetics derived mostly from ab initio calculations. The results predict that, during annealing of 40 keV B-implanted Si at 800 degree C, there exists a time window during which all the implanted boron atoms are substitutional. At earlier or later times, the interactions between free silicon self-interstitials and boron atoms drive the growth of boron clusters and result in an inactive boron fraction. The results show that the majority of boron TED takes place during the growth period of interstitial clusters and not during their dissolution. copyright 1998 American Institute of Physics.
1998-05-01
The SUERC AMS laboratory after 3 years
British Library Electronic Table of Contents (United Kingdom)
The new SUERC AMS Laboratory was described at AMS-9. Since then there have been technological developments, added and improved analysis capability, the formation of additional complementary groups, the purchase of another instrument, and many samples measured. Be, C, Al, Cl, Ca and I-AMS are established with measured species changing weekly. Full-terminal potential running is now routine and 5MV is proving sufficient for all species. Ion detection and evaluation has also been improved by the use of even thinner detector windows as necessary and a more powerful on-line data analysis system. Routine radiocarbon measurement is to 4permil reproducibility at middling current and graphite samples of as little as 100mg C can be accommodated. Even smaller samples can be measured as CO2 using He ca...
2007-01-01
Superconductivity on the threshold of magnetism in CePd{sub 2}Si{sub 2} and CeIn{sub 3}
Energy Technology Data Exchange (ETDEWEB)
The magnetic ordering temperature of some rare-earth-based heavy-fermion compounds is strongly pressure dependent and can be completely suppressed at a critical pressure, p{sub c}, making way for novel correlated electron states close to this quantum critical point. We have studied the clean heavy-fermion antiferromagnets CePd{sub 2}Si{sub 2} and CeIn{sub 3} in a series of resistivity measurements at high pressures up to 3.2 GPa and down to temperatures in the mK region. In both materials, superconductivity appears in a small window of a few tenths of a GPa on either side of p{sub c}. We present detailed measurements of the superconducting and magnetic temperature-pressure phase diagram, which indicate that superconductivity in these materials is enhanced, rather than suppressed, by the closeness to magnetic order. (author)
2001-03-26
Superconductivity on the threshold of magnetism in CePd_2Si_2 and CeIn_3
International Nuclear Information System (INIS)
The magnetic ordering temperature of some rare-earth-based heavy-fermion compounds is strongly pressure dependent and can be completely suppressed at a critical pressure, p_c, making way for novel correlated electron states close to this quantum critical point. We have studied the clean heavy-fermion antiferromagnets CePd_2Si_2 and CeIn_3 in a series of resistivity measurements at high pressures up to 3.2 GPa and down to temperatures in the mK region. In both materials, superconductivity appears in a small window of a few tenths of a GPa on either side of p_c. We present detailed measurements of the superconducting and magnetic temperature-pressure phase diagram, which indicate that superconductivity in these materials is enhanced, rather than suppressed, by the closeness to magnetic order. (author)
2001-03-26
Strong fields and recycled accelerator parts as a laboratory for fundamental physics
International Nuclear Information System (INIS)
Over the last few years it has become increasingly clear that low energy, but high precision experiments provide a powerful and complementary window to physics beyond the Standard Model. In this note we illuminate this by using minicharged particles as an example. We argue that minicharged particles arise naturally in extensions of the Standard Model. Compatibility with charge quantization arguments suggests that minicharged particles typically arise together with a massless hidden sector U(1) gauge field. We present several low energy experiments employing strong lasers, electric and magnetic fields that can be used to search for (light) minicharged particles and their accompanying U(1) gauge boson.
2009-12-01
Energy Technology Data Exchange (ETDEWEB)
Unlike the conventional automotive, modem railway trains are designed with non-openable windows; and a mechanical ventilation and air-conditioning (MVAC) system is installed in each train compartment for better indoor air quality as well as to provide a thermally comfortable environment. The ventilation rate is no doubt a critical element in the design of a MVAC system, especially in Hong Kong where the daily passenger load is extremely heavy. Earlier studies illustrated that carbon dioxide can be controlled at 1000 ppm by increasing the ventilation rate to 25.2 m{sup 3} h{sup -1}; however, it will also lead to an increase in energy consumption. In this paper, the electrical energy consumption at various ventilation rates was studied, and the cost of maintaining a low carbon dioxide level was estimated These provide solid information for the local railway companies to improve the air quality inside the train compartments. (author)
2000-01-01
Results from a Bragg Curve Spectrometer
International Nuclear Information System (INIS)
The Bragg Curve Spectrometer (BCS) is an ionization chamber long enough to stop particles of interest. Particles enter through the cathode window and leave an ionization track parallel to the electric field. The ionization electrons drift through a Frisch grid and are collected on an anode. The anode current, as a function of time, is proportional to the specific ionization along the track. The preamp output is split and used as input for two amplifiers, one with a long integration time constant for energy measurement, and one with a short time constant to pick off the maximum ionization or Bragg peak. The Bragg peak, which is proportional to the nuclear charge, is used for particle identification. Several versions of the BCS have been constructed and tested. Test results, detector characteristics and some design problems are discussed.
1984-10-01
Realization of good indoor climate in low-energy office
Energy Technology Data Exchange (ETDEWEB)
Good indoor air quality and thermal comfort, as well as low energy consumption, were achieved in an environment friendly experimental METOP-office building in Espoo, Finland. The consumption of heating and cooling energy was minimized by installation of energy-efficient windows, good CFC-free thermal insulation of the building envelope, the individually-controlled ventilation and room temperatures, heat recovery and energy-storing structures. According to the study carried out in 1990-1993, the heating energy was 13 kWh/m{sup 3}, 60% lower than the average consumption. The index of the satisfaction of thermal comfort was over 90%. Concentrations of all the measured indoor air pollutants were low. Ventilation rates could be chosen in each office room from 10 to 40 dm{sup 3}/s. The noise level of the ventilation system was low and the lighting level was pleasant. (author)
1994-12-31
RF conditioned dc discharges for excitation of rare gas halide lasers. Final report
Energy Technology Data Exchange (ETDEWEB)
Results of experiments performed utilizing high-power microwave sources for laser-discharge switching and preionization are reported. These results are not definitive, but are promising. Significant preionization using microwaves is possible. Some ability to switch the discharge and operate a laser have been demonstrated. More work needs to be performed to perfect the microwave coupling to the laser mixture. In particular, experiments with the microwaves better concentrated between the electrodes should be performed. The best way to accomplish this appears to be using the side-feed geometry; however, a large expansion of the microwaves should occur (to well below the power able to break down the window), and then a cylindrical lens should be used to focus the microwaves between the electrodes. 2 references.
1983-01-01
Picture processing computer to control movement by computer provided vision
Energy Technology Data Exchange (ETDEWEB)
The author introduces a multiprocessor system which has been specially developed to enable mechanical devices to interpret pictures presented in real time. The separate processors within this system operate simultaneously and independently. By means of freely moveable windows the processors can concentrate on those parts of the picture that are relevant to the control problem. If a machine is to make a correct response to its observation of a picture of moving objects, it must be able to follow the picture sequence, step by step, in real time. As the usual serially operating processors are too slow for such a task, the author describes three models of a special picture processing computer which it has been necessary to develop. 3 references.
1983-01-01
PDBpaint, a visualization webservice to tag protein structures with sequence annotations
British Library Electronic Table of Contents (United Kingdom)
Summary: Protein features are often displayed along the linear sequence of amino acids that make up that protein, but in reality these features occupy a position in the folded proteins 3D space. Mapping sequence features to known or predicted protein structures is useful when trying to deduce the function of those features and when evaluating sequence or structural predictions. To facilitate this goal, we developed PDBpaint, a simple tool that displays protein sequence features gathered from bioinformatics resources on top of protein structures, which are displayed in an interactive window (using the Jmol Java viewer). PDBpaint can be used either with existing protein structures or with novel structures provided by the user. The current version of PDBpaint allows the visualization of annot...
2011-01-01
International Nuclear Information System (INIS)
We report the fabrication of p"+/n junctions using Ge"+, C"+, and B"+ co-implantation and a spike anneal. The best junction exhibits a depth of 26 nm, vertical abruptness of 3 nm/decade, and sheet resistance of 520 Ohm/square. The junction location is defined by where the boron concentration drops to 10"1"8 cm"-"3. These junctions are close to the International Technology Roadmap specifications for the 65 nm technology node and are achieved by careful engineering of amorphization, stresses, and point defects. Advanced simulation of boron diffusion is used to understand and optimize the process window. The simulations show that the optimum process completely suppresses the transient-enhanced diffusion of boron and the formation of boron-interstitial clusters. This increases the boron solubility to 20% above the equilibrium solid-state solubility.
2005-08-01
British Library Electronic Table of Contents (United Kingdom)
This study presents new software, called Google Earth-based Optimal HAulage RouTing System (GEOHARTS), to improve the functionality of Google Earth for optimal haulage routing of off-road dump trucks in construction and mining sites. A modified least-cost path algorithm, which is applicable to working areas with both paved and unpaved temporary roads and can consider the effects of terrain relief and curves along a route on the route planning, was proposed and utilized for the software development. GEOHARTS can determine optimal haulage routes between loaders and dumps that ensure the least travel time or fuel consumption of off-road dump trucks and can visualize the results using an embedded 3D render window of Google Earth. The application to the Pasir open-pit coal mine in Indonesia dem...
2011-01-01
British Library Electronic Table of Contents (United Kingdom)
The Alpine Foreland Basin is a minor oil and moderate gas province in central Europe. In the Austrian part of the Alpine Foreland Basin, oil and minor thermal gas are thought to be predominantly sourced from Lower Oligocene horizons (Schoneck and Eggerding formations). The source rocks are immature where the oil fields are located and enter the oil window at ca. 4 km depth beneath the Alpine nappes indicating long-distance lateral migration. Most important reservoirs are Upper Cretaceous and Eocene basal sandstones.Stable carbon isotope and biomarker ratios of oils from different reservoirs indicate compositional trends in W-E direction which reflect differences in source, depositional environment (facies), and maturity of potential source rocks. Thermal maturity parameters from oils of di...
2011-01-01
Malaspina University-College's green building strategy
Energy Technology Data Exchange (ETDEWEB)
This brochure describes the strategy employed by the administration of Malaspina University--College in Nanaimo, British Columbia, to implement energy-efficient plans and integrating systems and plans that would allow the institution to consume less energy, fewer resources and improve the health and well-being of its students and staff. An assessment study to identify the most problematic areas, and to develop a prioritizing strategy for their replacement was the first step, followed by rigorous adherence to a 10- year cyclical replacement schedule. The program includes replacement of rooftop ventilation units, installation of high-performance glazing units to replace single-glazed windows, implementation of an Energy Management System to monitor heating, ventilating and air conditioning systems, and a Power Smart New Building Design and Building Improvements Program. The combined cost avoidance associated with these projects is estimated to reach $ 4.3 million ...
2000-01-01
Lorentz transmission electron microscopy investigation of magnetically patterned Co/Pt multilayers
Energy Technology Data Exchange (ETDEWEB)
The switching behavior of magnetic patterns prepared by ion irradiation was investigated. Co/Pt multilayers with perpendicular anisotropy and large out-of-plane coercivities 5-6 kOe were grown on electron transparent SiN windows. Regularly spaced 1 micron sized regions, were magnetically pattered via ion beam irradiation through a stencil mask. Lorentz TEM was used to observe in-situ magnetization reversal processes of irradiated regions under well-defined applied magnetic fields. When the in-plane field was increased, domain wall motion was observed, resulting in the alignment of the patterns with the direction of the applied field. The switching mechanism of the in-plane patterns was by domain wall motion.
2000-08-01
British Library Electronic Table of Contents (United Kingdom)
Considering the status of knowledge on corrosion and corrosion protection and especially the need for long term compatibility data of structural materials in HLM a set of experiments to generate reliable long term data was defined and performed. The long term corrosion behaviour of the two structural materials foreseen in ADS, 316L and T91, was investigated in the design relevant temperature field, i.e. from 300 to 550degreeC. The operational window of the two steels in this temperature range was identified and all oxidation data were used to develop and validate the models of oxide scale growth in PbBi. A mechanistic model capable to predict the oxidation rate applying some experimentally fitted parameters has been developed. This model assumes parabolic oxidation and might be used for de...
2011-01-01
Kinetics of gypsum crystal growth on a reverse osmosis membrane
British Library Electronic Table of Contents (United Kingdom)
The development of calcium sulfate dihydrate (gypsum) mineral scale in reverse osmosis (RO) membrane desalting was investigated by direct real-time observation of crystal growth. Gypsum scaling studies were conducted in a specially modified plate-and-frame reverse osmosis cell fitted with an optical window, with dark-field membrane lighting arrangement within the membrane cell to enhance crystal boundaries and allow recording of digital surface images magnified through an optical microscope. The evolution of the surface number density (SND) of gypsum crystals resembled a sigmoidal population growth process with an increasing rate of crystal formation at higher solution supersaturation (with respect to gypsum) at the membrane surface. The rate of formation of new crystals declined as the su...
2008-01-01
K_#beta#/K_#alpha#X-ray intensity ratio in the region of 15#<=#Z#<=#22
International Nuclear Information System (INIS)
The X-ray intensity ratio K_#beta#/K_#alpha# has been measured by using a 10 mCi "5"5Fe source (Mn K X-rays) and high resolution Si(Li) detector system coupled to a computer-controlled multichannel analyzer over the range of 15#<=#Z#<=#22. Correction have been made to the measured relative intensities (K_#alpha# and K_#beta# X-rays) for self-absorption in the sample, air, Be-window absorption and detection efficiency. The results are compared with those of other experiments and with the Scofield calculations. (author) 13 refs.; 3 figs.; 2 tabs.
1994-01-01
International Nuclear Information System (INIS)
In the Introduction the history of the cascade probabilistic method development is described. The calculation model for different charged particles cascade probabilistic functions (CPF) was considered. A new analytical expressions for CPF for electrons, protons, alpha-particles and ions are obtained as well. A new results on mathematical analysis, algorithms, and calculation of CPF with taking into account charged particles energy losses on computer are cited. The peculiarities of these functions are analyzed. The detail analysis of these function behavior in relation from flying particles energy, target atomic number, generation and registration depth, and interactions number is carried out. The program packages in the Windows medium is developed on the visual programming languages: Visual Basic 6.0, Delphi 6.0, C++ Builder 6.0.
Energy Technology Data Exchange (ETDEWEB)
Fuji Electric has realized highly reliable and functional control systems by the dispersion type control system FOCUS, which uses the controller (ICS-2000) enjoying good reputation in controlling industrial plants for a long time and a personal computer with high windows operability, the former for controlling and the latter for MHI responsible for monitoring. The smelting process in a steel-making plant needs a highly reliable system for advanced control to ensure continuous operation. Fuji Electric delivered the FOCUS system to Kubota in 1998, as the smelting furnace instrumentation/control system for the cupola furnace. The system has been in service smoothly. Moreover, a total of four control systems have been delivered, 2 for steel-making furnaces and the other 2 for continuous casting. (NEDO)
1999-01-10
Infrared monitoring of the Doublet III beam armor plate
Energy Technology Data Exchange (ETDEWEB)
An 80 keV, 3.6 MW neutral beam injection system has recently been installed on Doublet III, and the installation of a second system is scheduled within several months. Armor plate consisting of /approximately equals/100 graphite tiles (10 cm x 10 cm) coated with TiC has been plated over portions of the inner vacuum wall lying in the line of sight of the ion sources. In order to monitor the condition of the armor plate an infrared camera and a set of optical pyrometers have been installed alongside the beamline and view the armor plate through a CaF/sub 2/ window. The pyrometers measure the temperature of the armor plate associated with the maximum of the intensity distribution of each ion source.
1981-01-01
British Library Electronic Table of Contents (United Kingdom)
This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen, as well as Carbon Black as a high-value nano-material, with the bonus of zero CO2 emissions. The work focused on the development of a medium-scale solar reactor (10kW) based on the concept of indirect heating. The solar reactor is composed of a cubic cavity receiver (20cm side), which absorbs concentrated solar irradiation through a quartz window via a 9cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results were as follows: methane conversion and hydrogen yield of up to 98% and 90%, respectively, were achieved at 1770K, and acetylene was the most important by-product, with a mole fraction...
2009-01-01
Energy Technology Data Exchange (ETDEWEB)
The effects of group structures and weighting functions on neutron penetration through a thick Na-Fe geometry are studied. The recommended broad-group (61-neutron/23-gamma-ray) and few-group (22-neutron/10-gamma-ray) structures are tailored to the sodium and iron resonances, windows, and capture gamma-ray spectra. The best weighting functions are shown to be fine-group fluxes selected from a few key locations in the geometry. These group structures and weighting functions, relative to existing group structures and conventional weighting functions, improve the accuracy of the computed 61-neutron-group Bonner ball responses by up to one hundred percent and of the computed 22-neutron-group results by up to six hundred percent.
1987-01-01
Gear fault detection using customized multiwavelet lifting schemes
British Library Electronic Table of Contents (United Kingdom)
Fault symptoms of running gearboxes must be detected as early as possible to avoid serious accidents. Diverse advanced methods are developed for this challenging task. However, for multiwavelet transforms, the fixed basis functions independent of the input dynamic response signals will possibly reduce the accuracy of fault diagnosis. Meanwhile, for multiwavelet denoising technique, the universal threshold denoising tends to overkill important but weak features in gear fault diagnosis. To overcome the shortcoming, a novel method incorporating customized (i.e., signal-based) multiwavelet lifting schemes with sliding window denoising is proposed in this paper. On the basis of Hermite spline interpolation, various vector prediction and update operators with the desirable properties of biorthog...
2010-01-01
Energy Technology Data Exchange (ETDEWEB)
Incomplete convergence in numerical simulation such as computational physics simulations and/or Monte Carlo simulations can enter into the calculation of the objective function in an optimization problem, producing noise, bias, and topo- graphical inaccuracy in the objective function. These affect accuracy and convergence rate in the optimization problem. This paper is concerned with global searching of a diverse parameter space, graduating to accelerated local convergence to a (hopefully) global optimum, in a framework that acknowledges convergence uncertainty and manages model resolu- tion to efficiently reduce uncertainty in the final optimum. In its own right, the global-to-local optimization engine employed here (devised for noise tolerance) performs better than other classical and contemporary optimization approaches tried individually and in combination on the "industrial" test problem to be presented.
1999-05-18
British Library Electronic Table of Contents (United Kingdom)
Lithium phosphorous oxynitride(Lipon) thin films as a lithium ion conductive electrolyte were prepared by radio frequency reactive sputtering in N2 plasma. The properties of the amorphous Lipon solid electrolyte were investigated as a function of N2 pressure during reactive sputtering. The ionic conductivity and the electrochemical stability of Lipon thin films improved drastically as the N2 pressure decreased. The ionic conductivity closed to 10?6 S cm?1 and obtained a stability window of 1.0?5.0 V with an N2 pressure of 5 mTorr, where the number of nitrogen bonds between the phosphate groups were more than those formed at higher pressure. It was possible to fabricate the Li//LiCoO2 complete thin film battery using this Lipon solid electrolyte, which exhibited excellent discharge characte...
2006-01-01
Development of a solar thermal storage system suitable for the farmhouse heating in northeast China
Energy Technology Data Exchange (ETDEWEB)
This study reported on the performance of a passive solar radiant floor heating system designed for standard energy-saving farmhouses in northeast China. Weather data in the region was analyzed in terms of solar radiation, temperature, humidity and light levels. The heating characteristics of the building materials such as windows, doors, walls and roofs were also analyzed along with the indoor thermal environment of the farmhouse. The heating load was then calculated along with the size of the thermal storage element and the area of the collector element. The passive solar radiant floor heating system was designed for heating during the winter and cooling in summer. According to the results, the heating characteristics of the system have the potential to improve farming villages environment and the use of renewable energy.
2010-07-01
Capturing the Daylight Dividend
Energy Technology Data Exchange (ETDEWEB)
Capturing the Daylight Dividend conducted activities to build market demand for daylight as a means of improving indoor environmental quality, overcoming technological barriers to effective daylighting, and informing and assisting state and regional market transformation and resource acquisition program implementation efforts. The program clarified the benefits of daylight by examining whole building systems energy interactions between windows, lighting, heating, and air conditioning in daylit buildings, and daylighting's effect on the human circadian system and productivity. The project undertook work to advance photosensors, dimming systems, and ballasts, and provided technical training in specifying and operating daylighting controls in buildings. Future daylighting work is recommended in metric development, technology development, testing, training, education, and outreach.
2006-04-30
A Complete Detonator, Booster, and Main Charge Study of LX-07/PBX 9502
British Library Electronic Table of Contents (United Kingdom)
Abstract A complete study of an exploding bridgewire detonator (EBW), an LX-07 hemispherical booster and a PBX 9502 outer shell are described. Breakout times from all three are listed in terms of first impact on the booster, i.e., code times. Lucite windows are also used to obtain particle velocities at the edges of each explosive, and these are converted into explosive pressures. The key to modeling is the use of the profile of the aluminum detonator can as it impacts the booster, i.e., we need to know the curvature of the end of the booster can. Modeling even with coarse zoning shows that (i) using reactive flow in the booster is better than programmed burn, (ii) creating the flyer curvature helps, and (iii) creating the time differences of flyer impact helps even more.
2011-01-01
The importance and unique aspects of radiation protection in medicine
British Library Electronic Table of Contents (United Kingdom)
Radiation protection in medicine has unique aspects and is an essential element of medical practice. Medical uses of radiation occur throughout the world, from large cities to rural clinics. It has been estimated that the number of medical procedures using radiation grew from about 1.7 billion in 1980 to almost 4 billion in 2007. In spite of these large numbers, there are many parts of the world without adequate equipment, where the ability to perform additional medical procedures would likely result in a net benefit. Medicine accounts for more than 99.9% of the per caput effective dose from man-made sources. The goal in medical exposure is not to give the lowest dose, but to provide the correct dose to enable the practitioner to make the diagnosis or cure a tumour. Too little or too much ...
2010-01-01
TIMETAL reg-sign 21S property data
International Nuclear Information System (INIS)
TIMETAL reg-sign 21S, which has the nominal weight percent composition 15Mo, 3Al, 3Nb, and 0.2Si, is a metastable beta titanium alloy that offers a unique combination of high strength, good elevated temperature properties, and extraordinary environmental degradation resistance. It was developed by TIMET in 1988 as a foil matrix material for titanium metal matrix composites for the NASP, but currently monolithic applications are of much more significance. Among the alloy's unique properties are a high resistance to attack by commercial aircraft hydraulic fluids (commonly referred to as Skydrol trademark, which will be the term used in this paper) at all temperatures, which has led to its use in nacelle components on the Boeing 777 and other commercial aircraft. This paper provides an overview of the physical and mechanical properties of TIMETAL reg-sign 21S.
1993-02-21
Significance of chemical return in nuclear steam generators
International Nuclear Information System (INIS)
A reasonable understanding of PWR steam generator corrosion mechanisms such as denting and wastage has been developed, and adequate chemistry control programs defined to obviate the magnitude and effects of these modes of attack. However, relatively unique corrosion attack modes have been encountered at several plants notwithstanding the presence of a reasonable to very good chemistry control program when considered in light of the Steam Generator Owners Group chemistry guidelines. The uniqueness of attack also suggests that parameters not routinely measured or monitored may be playing a significant role. In the authors opinions, the only reasonable method of routinely identifying corrosion accelerating species present in crevices, sludge piles, and deposits in PWR steam generators is by performing detailed chemical return studies during power transients, shutdowns, and long term layups. Although it would be preferable to obtain samples from ...
1985-03-01
Quantitative easing works: Lessons from the unique experience in Japan 2001-2006
British Library Electronic Table of Contents (United Kingdom)
Abstract: The current financial crisis has now led most major central banks to rely on quantitative easing. The unique Japanese experience of quantitative easing is the only experience which enables us to judge this therapy's effectiveness and the timing of the exit strategy. In this paper, we provide a new empirical framework to examine the effectiveness of Japanese monetary policy during the ''lost'' decade and quantify the effect of quantitative easing on Japan's activity and prices. We combine advantages of Markov-switching VAR methodology with those of factor analysis to establish two major findings. First, we show that the decisive change in regime occurred in two steps: it crept out from late 1995 and established itself durably in February 1999. Second, we show for the first time th...
2011-01-01
Method and apparatus for spraying molten materials
Energy Technology Data Exchange (ETDEWEB)
A metal spray apparatus is provided with a supersonic nozzle. Molten metal is injected into a gas stream flowing through the nozzle under pressure. By varying the pressure of the injected metal, the droplet can be made in various selected sizes with each selected size having a high degree of size uniformity. A unique one piece graphite heater provides easily controlled uniformity of temperature in the nozzle and an attached tundish which holds the pressurized molten metal. A unique U-shaped gas heater provides extremely hot inlet gas temperatures to the nozzle. A particularly useful application of the spray apparatus is coating of threads of a fastener with a shape memory alloy. This permits a fastener to be easily inserted and removed but provides for a secure locking of the fastener in high temperature environments.
1996-01-01
Invariance, groups, and non-uniqueness: The discrete case
Energy Technology Data Exchange (ETDEWEB)
Lie group methods provide a valuable tool for examininginvariance and non-uniqueness associated with geophysical inverseproblems. The techniques are particularly well suited for the study ofnon-linear inverse problems. Using the infinitesimal generators of thegroup it is possible to move within the null space in an iterativefashion. The key computational step in determining the symmetry groupsassociated with an inverse problem is the singular value decomposition(SVD) of a sparse matrix. I apply the methodology to the eikonal equationand examine the possible solutions associated with a crosswelltomographic experiment. Results from a synthetic test indicate that it ispossible to vary the velocity model significantly and still fit thereference arrival times. the approach is also applied to data fromcorosswell surveys conducted before and after a CO2 injection at the LostHills field in California. The results highlight the fact that a faultcross-cutting the region ...
2005-03-24
Human factors assessments of innovative technologies: Robotics sector
International Nuclear Information System (INIS)
The U.S. Department of Energy (DOE) has funded major environmental technology developments over the past several years. One area that received significant attention is robotics, which has resulted in the development of a wide range of unique robotic systems tailored to the many tasks unique to the DOE complex. These systems are often used in highly hazardous environments, which reduces or eliminates worker exposures. The DOE, concurrent with the technology development initiative, also established and funded a 5-yr cooperative agreement intended to interface with the technology development community-with specific attention to the occupational safety and health aspects associated with individual technologies through human factors and hazard assessments. This program is now in its third year.
1997-11-16
Construction of the maximal solution of Backus? problem in geodesy and geomagnetism
British Library Electronic Table of Contents (United Kingdom)
The (simplified) Backus? Problem (BP) consists in finding a harmonic function u on the domain exterior to the three dimensional unit sphere S, such that u tends to zero at infinity and the norm of the gradient of u takes prescribed values g on S. Except for a change of sign, the solution is not unique in general. However, there is uniqueness of solutions in the class of functions with the additional property that the radial component of the gradient of u on S is nonpositive. This is the geodetically relevant case. If a solution u with this property exists, then u is the maximal solution of the problem (and -u the minimal one). In this paper we propose a method of successive approximations to get this particular solution of BP and prove the convergence for functions g close to a constant fu...
2011-01-01
Wind turbine fault diagnosis based on Morlet wavelet transformation and Wigner-Ville distribution
Energy Technology Data Exchange (ETDEWEB)
Based on the Morlet wavelet transformation and Wigner-Ville distribution (WVD), we present a wind turbine fault diagnosis method in this paper. Wind turbine can be damaged by moisture absorption, fatigue, wind gusts or lightening strikes. Due to this reason, there is an increasing need to monitor the health of these structures. Vibration analysis is the best-known technology applied in wind turbine condition monitoring, in which the time-frequency analysis techniques such as Wigner-Ville distribution (WVD) are widely used. Theoretically WVD has an infinite resolution in time-frequency domain. For early wind turbine fault signals, however, there are two main difficulties in WVD analysis. One is strong noise signals in the background and the other is cross terms in WVD itself. In this paper, continuous wavelet transformation (CWT) is employed to filter useless noise in raw vibration signals, and auto terms window (ATW) function is used to suppress the cross terms in ...
2010-12-15
Energy Technology Data Exchange (ETDEWEB)
Apatite fission track analysis, vitrinite reflectance data, and K-Ar dating of Permian-Carboniferous and Mesozoic core samples have been successfully integrated to reconstruct the thermal and tectonic history of the Ordos basin, China. Apatite fission track ages of Carboniferous-Jurassic sedimentary rocks range between 3 and 137 Ma, and are significantly younger than the stratigraphic ages. Confined fission track lengths demonstrate exclusively mixed length distribution, indicating complex thermal history. The data suggest that the samples must have all experienced higher paleotemperatures in the past. Mean virtinite reflectance values (R{sub o}) of the Triassic rocks range from 0.61 to 1.06%, giving a high coalification gradient of 0.36%/km and suggesting a high paleothermal gradient of 57{degrees}C/km. Permian-Carboniferous rocks have R{sub o} values on the order of 1.0-3.0%, and locally up to 4.0-6.0%. Some high R{sub o} values coincide with positive gravity and magnetic anomalies. ...
1996-07-01
The pisa experiment: spallation products identified by bragg curve spectroscopy
International Nuclear Information System (INIS)
In the framework of spallation neutron sources and accelerator-driven systems, the international PISA (Proton-induced Spallation) collaboration has initiated measurements of total- and double-differential cross-sections for products of spallation reactions in a wide range of target nuclei (GU) at the COSY proton accelerator in Julich (Germany). The purpose is to study secondary particle production created in structural, window and target materials via proton beams up to 2.5 GeV of incident kinetic energy. Residual nuclei [H, He up to intermediate mass fragment (IMF)] production cross-sections are of great importance for estimating the damage to target and structure materials involving the planned spallation neutron sources, given that the lifetime of window and target materials is directly associated to those cross-sections. The demand for reliable theoretical predictions on production cross-sections is by no means satisfied by the models and ...
2004-05-17
Some fundamental factors in quantitative analysis by ion microanalyzer
International Nuclear Information System (INIS)
In analysis of hydrogen in metals and alloys by SIMS, control of the hydrogen blank mainly due to residual gases is a persistent problem. Contrarity, this problem becomes less important in case of deuterium analysis. The prescribed amounts of deuterium were introduced into a pure titanium and a beta-titanium alloy (Ti- 6.6wt%Fe) by the gas reaction method. Intensities of the various secondary ions sputtered from each sample were measured by the Hitachi Ion Microanalyzer with primary ions of Ar"+. Energy distributions of the various secondary ion species were measured with the energy window of about 15eV width. The effects of oxygen gas pressure in the target chamber and the bulk deuterium concentration on the shape of energy distribution curves are discussed. For all samples, intensity of D"- ions is higher than that of D"+ ions, especially at higher energy ranges. With increasing the deuterium concentration: a) intensities of D"+ and D"- ions from Ti-D system ...
Energy Technology Data Exchange (ETDEWEB)
The Rebi Block is currently in the early stages of hydrocarbon exploration. The subsurface geology of this area is only known from seismic reflection data. By applying seismic stratigraphy techniques, unconformities and condensed sections were recognized. These discontinuities were dated using paleontological information from the Kulka-1 well, Northwest Shelf of Australia. With these age constraints, seven unconformities and three condensed sections were dated and correlated to the Exxon global sea level curve. The chronostratigraphic charts for the Rebi Block and the Northwest Shelf of Australia have clarified the Mesozoic stratigraphy of the study area. The Exxon global sea level curve has refined the ages determined by conventional paleontological dating. The chart has also helped in predicting source, reservoir and seal potential within a time framework. Prospective stratigraphic traps were those related to the incised valleys at the southeastern part of the Rebi Block. Although ...
1996-12-31
Radon measurements in soil - tests in Krakow agglomeration
International Nuclear Information System (INIS)
The migration of gaseous radon through the soil is depending on the geology of the region and may vary locally because of occurrence of fractures in impermeable layers and existence of fractures and faults. To identify areas with elevated radon concentration in soil gas, it is very helpful to know the geological structure of the area under study and how the high permeability soils are situated in the overburden. Topography of the surface in the Krakow area is determined by exhumed structure of late Alpine foreland, dismembered into systems of several normal fault-bounded carbonate horsts, erosional monadocks and grabens, and partially filled with marine Miocene clays of Carpathian foredeep basin. Radon geofluid, generated partially in sub-Jurassic, U-rich crystalline basement, migrates vertically to surface through permeable, jointed, faulted and karstified Jurassic limestone. Under the cover the radon fluxes are channelled by adjacent list ric faults and clay/limestone interfaces ...
2000-10-14
Pulse power considerations for the generation of 45 #mu#s, 200 keV electron beams for CO_2 lasers
International Nuclear Information System (INIS)
A two module electron beam source operating over a wide range of output parameters has been designed and fabricated to be used in conjunction with a pair of electron beam sustained CO_2 lasers. Each module comprised a grid-controlled thermionic electron beam gun including a compact grid pulser for control of the electron beam, a 250 kV thyratron switched modulator for acceleration of the electron beam, a 1 kHz filament heater and a complex computerized control system. The system was designed to reliably produce 45 #mu#s wide electron pulses of 150-200 keV energy, operate at repetition rates of 1-10 pps and current densities of 5-20 mA/cm"2. Additional parameters are listed. The high voltage cathode assembly employs 132 thoriated tungsten filaments distributed over the area of the 250 cm x 10 cm output window. The cathode assembly including the control grids is supported by two high voltage ceramic bushings in a stainless steel vacuum chamber. For acceleration of ...
1989-01-19
Polyp measurement based on CT colonography and colonoscopy: variability and systematic differences
Energy Technology Data Exchange (ETDEWEB)
To assess the variability and systematic differences in polyp measurements on optical colonoscopy and CT colonography. Gastroenterologists measured 51 polyps by visual estimation, forceps comparison and linear probe. CT colonography observers randomly assessed polyp size two-dimensionally (abdominal and intermediate window) and three-dimensionally (manually and semi-automatically). Linear mixed models were used to assess the variability and systematic differences between CT colonography and optical colonoscopy techniques. The variability of forceps and linear probe measurements was comparable and both showed less variability than measurement by visual assessment. Measurements by linear probe were 0.7 mm smaller than measurements by visual assessment or by forceps. The variability of all CT colonography techniques was lower than for measurements by forceps or visual assessment and sometimes lower (only 2D intermediate window and manual 3D) ...
2010-06-15
Is the Short Distance Scale a Result of a Problem with the LMC Photometric Zero Point?
Energy Technology Data Exchange (ETDEWEB)
I present a promising route to harmonize distance measurements based on clump giants and RR Lyrae stars. This is achieved by comparing the brightness of these distance indicators in three environments: the solar neighborhood, Galactic bulge and Large Magellanic Cloud (LMC). As a result of harmonizing the distance scales in the solar neighborhood and Baade's Window, I derive the new absolute magnitude of RR Lyrae stars, M{sub v}(RR) at [Fe/H] = -1.6 (0.59 {+-} 0.05, 0.70 {+-} 0.05). Being somewhat brighter than the statistical parallax solution, but fainter than typical results of the main sequence fitting to Hipparcos data, these values of M{sub V}(RR) favor intermediate or old ages of globular clusters. Harmonizing the distance scales in the LMC and Baade's Window, I show that the most likely distance modulus to the LMC, {mu}{sub LMC} is in the range 18.24 - 18.44. The Hubble constant of about 70 km/s/Mpc reported by the HST ...
2004-03-29
Improvements in SISCOM II technology; Introduccion de Mejoras Tecnologicas en el SISCOM II
Energy Technology Data Exchange (ETDEWEB)
This document is the Final Report for the project Introduccion de Mejoras Tecnologicas en el SISCOM II, or Improvements in SISCOM II Technology. It consists of a brief description of the activities carried out during the project, and several Annexes that explain in a deeper way each result. SISCOM II is the main telemetry system currently in use in the Spanish underground coal mining, but it was developed ten years ago and needed a technological update, which was the objective of this project. The aims of the project were: To develop Hardware and Software for the Out stations currently used (maintenance developments) To design new hardware and software, easier to use in the current and new applications of SISCOM II Both objectives were met, although not in the way originally intended. The main results were: In the field of old Out stations update: A new set of boards for the old Out stations was developed Out station's firmware was updated for the new hardware In the field new ...
2000-07-01
Improvements in SISCOM II Technology; Introduccion de Mejoras Tecnologicas en el SISCOM II
Energy Technology Data Exchange (ETDEWEB)
This document is the Final Report for the project. Improvements in SISCOM II Technology. It consists of a brief description of the activities carried out during the project, and several Annexes that explain in a deeper way each result. SISCOM II is the main telemetry system currently in use in the Spanish underground coal mining, but it was developed ten years ago and needed a technological update, which was the objective of this project. The aims of the project were: - To develop Hardware and Software for the Outstations currently used (maintenance developments) - To design new hardware and software, easier to use in the current and new applications of SISCOM II Both objectives were met, although not in the way originally intended. The main results were: In the field of old Outstations update: - A new set of boards for the old Outstations was developed - Outstations`s firmware was updated for the new hardware In the field new hardware and software design: - SISCOM II Supervision ...
1998-12-31
Energy Technology Data Exchange (ETDEWEB)
A borehole televiewer (BHTV) logging was conducted to investigate cracks in bored wells. The logging process shoots ultrasonic waves onto bore walls and utilizes reflection waves from the bore walls. If the bores are filled with muddy water, or the ultrasonic waves can pass through even if vinyl chloride tubes have been inserted after excavation, the state of the bore walls can be investigated in principle. Conventional optical scanners are, however, incapable of making this investigation. The BHTV logging can be used for identifying lithofacies from reflection intensities from bore walls (it depends on sound impedance of rocks), not to speak of finding cracks. As a result of making logging upon setting time windows from 105 to 145 {mu} sec in a bored well inserted with a vinyl chloride tube, cracks in the bore wall were identified clearly through the vinyl chloride tube. If the distance between the bore wall and the vinyl chloride tube becomes smaller, setting the ...
1997-05-27
Evolution of oil-generative window and oil and gas occurrence in Tertiary Niger delta basin/sup 1/
Energy Technology Data Exchange (ETDEWEB)
Assuming a simple model of delta development involving progradation and uniform burial at 500 m/m.y. (1,640 ft/m.y.) to present depths, oil-genesis nomographs derived from the time-temperature index (TTI) method were constructed for geothermal gradients ranging from 2.2/sup 0/ to 5.1/sup 0/ C/100 m (1.2/sup 0/-2.8/sup 0/ F/100 ft) of the Niger delta and used in mapping the positions (depth, temperature) of the top of the oil-generative window (OGW) at various times between 40 m.y.B.P. and the present. During the active subsidence phase, oil generation within any megasedimentary unit was initiated at a temperature of 140/sup 0/-146/sup 0/C (284/sup 0/-294.8/sup 0/F) and depth of 3,000-5,200 m (9,843-17,060 ft) within 7-11 m.y. after deposition of the potential source rocks. After cessation of subsidence, vertical upward movement of the OGW by 800-1,600 m (2,625-5,249 ft) was accompanied by a temperature lowering of 23/sup 0/-54/sup 0/C (41/sup 0/-97/sup 0/F), ...
1984-11-01
Evolution of oil-generative window (OGW) in Niger delta basin
Energy Technology Data Exchange (ETDEWEB)
Assuming a simple model of delta development involving progradation and uniform subsidence to present depths (rate, 500 m/m.y.; 1640 ft/m.y.), oil-genesis nomographs derived from the TTI method were constructed for various geothermal gradients of the Niger delta (2.2., 2.5., 2.9, 3.6, 4.0, 4.4, and 4.7/sup 0/C/100 m) and utilized in mapping the positions (depth, temperature) of the top of the oil-generative window (OGW) at arbitrarily selected times (40 m.y.B.P., 30 m.y.B.P., 15 m.y.B.P., and the present). About 200 data points were evaluated. During the active subsidence phase, oil generation within any megastructure was initiated at a temperature of 140 to 146/sup 0/C (284 to 294/sup 0/F) and depth of 3000 to 5200 m (9842 to 17,060 ft) within 7 to 11 m.y. after deposition of the potential source rocks. After cessation of subsidence, upward movement of the OGW by 800 to 1600 m (2624 to 5249 ft) was accompanied by a temperature lowering of 23 to 54/sup 0/C (73 to ...
1983-03-01
Development of 2-D velocity structure model input tool
Energy Technology Data Exchange (ETDEWEB)
The seismic reflection exploration technique which is one of the geophysical methods for oil exploration became effectively to image the subsurface structure with rapid development of computer. As a tool to perform seismic inversion, seismic forward modeling program using ray tracing should be developed. In this study, we have developed the algorithm that is to calculate the travel time of the complex geological structure using ray tracing by subdividing the geologic model into triangular element (finite element) having the constant velocity. We can analytically calculate Jacobian with some information by this current ray tracing. With this Jacobian, we will develop new algorithm which is to obtain geological properties and to image the subsurface. Since the FEM (Finite Element Method) ray tracing we have developed goes well the inverse velocities structure, we can apply the inversion problem to complex geological model. For the convenience of velocity model input data which is needed ...
1996-12-01
Construction, testing of the 1 MW, 130-260 GHz Fusion-FEM
Energy Technology Data Exchange (ETDEWEB)
During the previous 9 months the major part of the Fusion-FEM has been constructed. The 2 MV Insulated Core Transformer, the electron gun, the accelerator, the focusing lenses and the undulator have been tested on-site. In the present - temporary - set-up, the electron beam line consists of a 12 A, 80 keV thermionic electron gun, a 2 MeV dc accelerator, beam transport optics, the undulator and a collector. The gun is mounted in the high voltage terminal, which is now at -2 MV, and the undulator and mm-wave system am at ground potential outside the SF{sub 6}-filled pressure tank. This so-called inverse set-up allows easy access to the larger part of the beam line, the undulator and the mm-wave system, which is important in the conditioning phase. The decelerator and depressed collector am not yet installed. The design of the electron beam line has been optimised using the GPS particle-tracking code and the TOSCA code. The TOSCA code is used for accurate field calculations of the ...
1995-12-31
Wear resistant composite structure of vitreous carbon containing convoluted fibers. Final report
Energy Technology Data Exchange (ETDEWEB)
Energy Related Inventions Program Number 613 was a two year program to commercialize a unique new wear material, Metal Reinforced Carbon Composite, MRCC. The program was designed to manufacture sample components of MRCC for evaluation by potential users and manufacturers. As a result of the program Burton Technologies Inc. and Rotary Power International are forming a joint company to manufacture, market and license MRCC materials to a wide range of industries.
1996-05-28
UK PubMed Central (United Kingdom)
When high-purity copper (≥99.98%wt) is melted, held in its liquid state for a few hours with iterative thermal cycling, then allowed to resolidify, the ingot surface is found to have...Full Text Available
2009-12-24
UK PubMed Central (United Kingdom)
Spider venoms provide a highly valuable source of peptide toxins that act on a wide diversity of membrane-bound receptors and ion channels. In this work, we report isolation, biochemical analysis, and...Full Text Available
2010-06-11
Tropospheric sampling with aircraft
Energy Technology Data Exchange (ETDEWEB)
Aircraft constitute a unique environment which places stringent requirements on the instruments used to measure the concentrations of atmospheric trace gases and aerosols. Some of these requirements such as minimization of size, weight, and power consumption are general; others are specific to individual techniques. This review presents the basic principles and considerations governing the deployment of trace gas and aerosol instrumentation on an aircraft. An overview of common instruments illustrates these points and provides guidelines for designing and using instruments on aircraft-based measurement programs.
1991-03-01
Transitional nuclei and triaxial shapes
International Nuclear Information System (INIS)
Evidence for triaxial nuclear shapes from families of unique-parity states in transitional odd-A nuclei around mass A=190 and A=130 is reviewed. The experimental data are analysed within the odd-A triaxial core model. Regular two-dimensional band patterns are found in experiment and are shown to be a consequence of broken axial symmetry. Recent theoretical developments are discussed including the question of how stable the triaxial shapes are.
The unique hypusine modification of eIF5A promotes islet ? cell inflammation and dysfunction in mice
UK PubMed Central (United Kingdom)
In both type 1 and type 2 diabetes, pancreatic islet dysfunction results in part from cytokine-mediated inflammation. The ubiquitous eukaryotic translation initiation factor 5A (eIF5A), which is the...Full Text Available
2010-06-01
The chemical properties of silica particle surface in relation to silica-cell interactions
Energy Technology Data Exchange (ETDEWEB)
Although silicosis has been studied extensively, the mechanism is still not fully understood. Experiments do provide evidence that the actions of unique properties of silica surface on the cell membrane are the starting point of silicotic processes. This paper summarizes literature on chemical properties of silica surface, and the effect of particle size on silica toxicity. This paper also discusses the ways in which silica dusts are though to interact with the cell membrane, with emphasis on freshness, hydrogen bonding, and free-radical interactions.
1989-01-01
UK PubMed Central (United Kingdom)
BackgroundCannabinoids represent unique compounds for treating tumors, including astrocytomas. Whether CB1 and CB2 receptors mediate this therapeutic effect...Full Text Available
Stefan problem with a convective boundary condition
International Nuclear Information System (INIS)
We study the one-phase Stefan problem on a semi-infinite strip x> or =0, with the convective boundary condition -KT/sub x/(0,t) = h[T/sub L/--T(0,t)]. Points of intrest include: a) behavior of the surface temperature T(0,t); b) asymptotic behavior as h#->#infinity; c) uniqueness, and d) bounds on the phase change front and total system energy.
1982-01-01
Sr3(Al3+xSi13?x)(N21?xO2+x):Eu2+ (x ? 0): a monoclinic modification of Sr-sialon
UK PubMed Central (United Kingdom)
The structure of the title compound, Sr-bearing oxonitridoaluminosilicate (Sr-sialon), contains two types of channels running along the a axis, with the three unique Sr atoms...Full Text Available
Repowering and retrofits: building on past value
Energy Technology Data Exchange (ETDEWEB)
Amidst the explosion of greenfield natural gas-fired combined-cycle plant development, opportunities still exist for valuable plant repowering and retrofits by taking advantages of unique technical and market conditions. One of the projects discussed is the rebuilding of the coal-fired Hawthorne unit 5 damaged by a boiler explosion. 3 tabs., 5 photos.
2000-01-01
Public agency partnership: Hanford`s history artifacts as a communications tool
Energy Technology Data Exchange (ETDEWEB)
The Hanford Site in eastern Washington state currently is engaged in the largest waste cleanup in world history. In order to make informed decisions about remediation options, the public throughout the Pacific Northwest and the nation needs to understand the wastes that are present, their sources of generation, their composition, and their behavior in the environment. The fact that Hanford operations` were conducted in secret for over four decades presents a unique public information challenge to those who currently are responsible for communicating with the public.
1994-02-01
Principles of photon colliders
Energy Technology Data Exchange (ETDEWEB)
Future linear colliders offer unique opportunities to study {gamma}{gamma}, {gamma}e interactions. Using the laser backscattering method one can obtain {gamma}{gamma}, {gamma}e colliding beams with energy and luminosity comparable to the electron-position luminosity or even higher. In this review physical principles of photon colliders are described and various problems, concerning the accelerator, laser, interaction region and luminosity are discussed. Some examples of physical processes are given. ((orig.)).
1995-02-01
Pneumatic conveying of sensitive compounds during nuclear fuel fabrication
International Nuclear Information System (INIS)
Any transport of nuclear material is associated with the risk of contamination after release into working areas or environment. stationary installed safe geometry vessels with pneumatic transfer between them offer unique safety features and reduce operating costs. The article describes the case of HTR fuel spheres, where a specially designed conveying system has been developed and the prototype conveyor has been tested.
Physical Properties of Liquid Crystals
This handbook is a unique compendium of knowledge on all aspects of the physics of liquid crystals. In over 500 pages it provides detailed information on the physical properties of liquid crystals as well as the recent theories and results on phase transitions, defects and textures of different types of liquid crystals. An in-depth understanding of the physical fundamentals is a prerequisite for everyone working in the field of liquid crystal research. With this book the experts as well as graduate students entering the field get all the information they need.
1999-01-01
Organisation and training of coke oven management
Energy Technology Data Exchange (ETDEWEB)
Japan`s coke industry was developed as the basic part for iron and steel industry. The paper addresses two factors as a characteristic of Japan-unique management. One topic is operation management and equipment management of coke factory; the second topic is human resource training in a company that lies under each management. The concepts and actual methods of these topics are introduced by showing examples. The paper discusses the improvement of the working environment and measures for future employment caused by the aging problem in Japan. 5 figs.
1994-12-31
Optimal Quantum State Estimation by No-Signaling Principle
We obtain a simple derivation of the optimal quantum state estimation of a two-level system using the no-signaling principle. In particular, we show that the no-signaling principle determines the unique form of the guessing probability, independently to a given figure of merit such as the fidelity or the information gain. This proves that optimal measurements for a two-level quantum system is the same for almost all figures of merit.
2010-01-01
One-loop Helicity Amplitudes for Top Quark Pair Production in Randall-Sundrum Model
In this paper, we show how to calculate analytically the one-loop helicity amplitudes for the process $q\\bar{q} rightarrow t\\bar{t}$ induced by KK gluon, using the spinor-helicity formalism. A minimal set of Feynman rules which are uniquely fixed by gauge invariance and the color representation of the KK gluon are derived and used in the calculation. Our results can be applied to a variety of models containing a massive color octet vector boson.
2011-01-01
In this paper, we study the existence and uniqueness of periodic solutions of the differential equation of the form . Here, we obtain some sufficient conditions which guarantee the existence of periodic solutions. This equation is a quite general third- order nonlinear vector differential equation, and one example is given for illustration of the subject.
2011-01-01
Non-uniqueness in conformal formulations of the Einstein constraints
Standard methods in non-linear analysis are used to show that there exists a parabolic branching of solutions of the Lichnerowicz-York equation with an unscaled source. We also apply these methods to the extended conformal thin sandwich formulation and show that if the linearised system develops a kernel solution for sufficiently large initial data then we obtain parabolic solution curves for the conformal factor, lapse and shift identical to those found numerically by Pfeiffer and York. The implications of these results for constrained evolutions are discussed.
2006-01-01
Nanocrystalline materials: Interfaces and mesoscopic correlations studied by neutron scattering
International Nuclear Information System (INIS)
Nanocrystalline materials can exhibit properties which are considerably different from their coarse-grained counterparts, making them unique for basic or applied research and also very promising for potential applications. The topics which are addressed in the present paper are magnetic properties and magnetic correlations on the nanometer scale, mechanical properties, in particular the influence of grain boundaries on the elastic and plastic behaviour, and vibration models of grain boundary atoms in nanostructured materials. (author)
2001-09-23
Model for ionic hopping in Li/sub 3/N
Energy Technology Data Exchange (ETDEWEB)
Analysis of published NMR relaxation data of /sup 6/Li and /sup 7/Li in Li/sub 3/N leads to a unique model fo Li/sup +/ hopping along the c-axis. It is one in which an ion goes directly from one Li(1) plane to another Li(1) plane by passing through the intermediate Li(2) plane.
1980-08-01
Energy Technology Data Exchange (ETDEWEB)
In 1994, after four years of preparation, the first off-shore wind farm in the Netherlands was erected. The ``Lely`` wind farm comprises four NedWind 500 kW wind turbines, of rotor diameter 40.77 m. The turbines are placed on unique single-pile foundations. An interesting engineering aspect of the project is the interaction between the foundations and the turbine. (author)
1996-09-01
Large-scale fabrication of TiO2 hierarchical hollow spheres.
In this Communication, we report the fabrication of well-crystallized rutile-phase TiO2 hollow spheres using potassium titanium oxalate as the precursor. The spheres exhibited unique three-dimensional hierarchical architectures and demonstrated a significantly improved photocatalytic performance. The synthetic strategy used in this process represents a general approach and therefore may contribute to the formation mechanisms of hollow nanostructures. PMID:16634578
2006-05-01
UK PubMed Central (United Kingdom)
BackgroundAs EBV-associated gastric cancer has unique features that are different from EBV (-) gastric cancer, EBV is considered to have a key role in gastric carcinogenesis. It...Full Text Available
Irradiation test program for FFTF
International Nuclear Information System (INIS)
Four unique deisgn features are described which make the Fast Flux Test Facility eminently suitable for irradiation test programs. These features are a fast flux level of 7 x 10"1"5 neutrons/cm"2/sec, a 36-inch reference (breeder reactor) core height, test volumes suitable for testing of statistical quantities of materials, and the capability for direct (contact) or indirect (proximity) instrumentation of active core experiments.
Hydroelectricity - An Answer To Energy Needs
Energy Technology Data Exchange (ETDEWEB)
The energy challenges of the next 30 years appear daunting and, in certain cases, in conflict with one another. Their complexity is such that one solution alone cannot provide a full answer. It is nevertheless equally clear that hydro-electricity, being renewable, proven, highly efficient, storable and with still very significant resource potential, possesses a unique combination of attributes which will aid decision-makers to plan and execute energy development with confidence.
2010-09-15
Hybridization and crystal field in YbPd_2Si_2
International Nuclear Information System (INIS)
Experimental data in the Kondo lattice YbPd_2Si_2 is compared with the results of a hybridization model, based ont he 'large degeneracy expansion' approximation, which takes into account the crystal field level splittings of the Yb ion. We show that satisfactory agreement is obtained with a unique set of crystal field and hybridization parameters. (orig.).
Hybridization and crystal field in YbPd sub 2 Si sub 2
Energy Technology Data Exchange (ETDEWEB)
Experimental data in the Kondo lattice YbPd{sub 2}Si{sub 2} is compared with the results of a hybridization model, based ont he 'large degeneracy expansion' approximation, which takes into account the crystal field level splittings of the Yb ion. We show that satisfactory agreement is obtained with a unique set of crystal field and hybridization parameters. (orig.).
1991-05-01
Global quantum gauge symmetry via reconstruction theorems
Energy Technology Data Exchange (ETDEWEB)
In this paper we establish that every quantum field theory satisfying some basic axioms possesses a weak quasi Hopf algebra as gauge symmetry. We use a reconstruction theorem to find this symmetry algebra and show how it is sed to build a gauge covariant field algebra. We investigate the question of why this generality is necessary. The non-uniqueness of the reconstruction process is interpreted and a cohomological classification of possible global gauge symmetries is given. (author)
1996-12-21
UK PubMed Central (United Kingdom)
Outbreaks of disease attributable to human error or natural causes can provide unique opportunities to gain new information about host-pathogen interactions and new leads for pathogenesis research....Full Text Available
Finding the best quadratic approximation of a function
British Library Electronic Table of Contents (United Kingdom)
This article examines the question of finding the best quadratic function to approximate a given function on an interval. The prototypical function considered is f(x) = ex. Two approaches are considered, one based on Taylor polynomial approximations at various points in the interval under consideration, the other based on the fact that three non-collinear points determine a unique quadratic function. Three different techniques for measuring the error in the approximations are considered.
2011-01-01
FLASH-the first soft x-ray free electron laser (FEL) user facility
Energy Technology Data Exchange (ETDEWEB)
The free electron laser (FEL) FLASH at DESY in Hamburg is the first x-ray FEL ever built. Many new developments were necessary in order to exploit the unique properties of this novel light source for scientific experiments. The facility has constantly been improved and several major upgrades have been made or are currently underway. This paper reviews the main characteristics of the user facility as well as the major developments and upgrades.
2010-10-14
Development of LMFBR safety testing in FFTF
International Nuclear Information System (INIS)
The Fast Flux Test Facility (FFTF) will provide a prototypic test environment for advanced fuels and materials development within the U. S. LMFBR program. As a fast test reactor, the FFTF also provides a potentially unique capability for conduct of safety experimentation relevant to selected LMFBR safety issues associated with postulated core disruption events. The utility and feasibility of possible extension of FFTF testing into the area of safety research is being investigated. 5 fig.
1976-10-01
Depth profile of uncompensated spins in an exchange bias system
Energy Technology Data Exchange (ETDEWEB)
We have used the unique spatial sensitivity of polarized neutron and soft x-ray beams in reflection geometry to measure the depth dependence of magnetization across the interface between a ferromagnet and antiferromagnet. The new uncompensated magnetization near the interface responds to applied field, while the uncompensated spins in the antiferromagnetic bulk are pinned, thus providing a means to establish exchange bias.
2005-05-17
Comparison of SAND-II and FERRET
A comparison was made of the advantages and disadvantages of two codes, SAND-II and FERRET, for determining the neutron flux spectrum and uncertainty from experimental dosimeter measurements as anticipated in the FFTF Reactor Characterization Program. This comparison involved an examination of the methodology and the operational performance of each code. The merits of each code were identified with respect to theoretical basis, directness of method, solution uniqueness, subjective influences, and sensitivity to various input parameters.
Calculation of general p-adic Feynman amplitude
Energy Technology Data Exchange (ETDEWEB)
The general n-point massless p-adic Feynman amplitude with arbitrary parameters of analytic regularization for each line is calculated. This result is presented in the form of a sum over hierarchies of a given graph. The structure of ultraviolet and infrared divergences of p-adic Feynman amplitudes is characterized and the star-triangle uniqueness identity in the p-adic case is derived. (orig.).
1992-10-01
UK PubMed Central (United Kingdom)
The CNS is a unique organ due to its limited capacity for immune surveillance. As macrophages of the CNS, microglia represent a population originally known for the ability to assist neuronal stability,...Full Text Available
Beyond "Little Taipei": The Development of Taiwanese Immigrant Businesses in Los Angeles.
Qualitative and quantitative techniques, including a telephone survey of 310 Taiwanese business owners, were used to study the unique features of Taiwanese immigrant businesses in Los Angeles (California). When provided with entrepreneurial capital, Taiwanese enterprises grow rapidly in the context of Los Angeles's economic restructuring. (SLD)
1994-12-01
An immunochemical approach to the study of DNA damage and repair
Energy Technology Data Exchange (ETDEWEB)
The overall objective of this project is to produce antibodies to unique modified DNA bases and develop immunochemical assays to quantitate these lesions in damaged DNA. During this past year we have developed an antibody and chemical test to quantitate a basic sites in DNA and produced antibodies to the 8-oxopurines. This report discusses the detection of a basic sites in DNA and the preparation of antibodies to 8-hydroxyadenine and 8-hydroxyguanine.
1990-11-14
UK PubMed Central (United Kingdom)
BackgroundThe mitochondrial genome of the Octocorallia has several characteristics atypical for metazoans, including a novel gene suggested to function in DNA repair. This mtMutS...Full Text Available
UK PubMed Central (United Kingdom)
The structure of unintegrated human immunodeficiency virus type 1 (HIV-1) DNA from acutely infected human lymphoid cells was analyzed by nuclease S1 cleavage. We observed a unique, discrete single-stranded...Full Text Available
1991-05-01
UK PubMed Central (United Kingdom)
AbstractT-box family transcription factors play many roles in Metazoan development. Here we characterise Tbx6r, a unique Tbx6 paralogue isolated from the amphibian Xenopus....Full Text Available
2010-04-01
UK PubMed Central (United Kingdom)
Ethylene (C2H4) is a unique plant-signaling molecule that regulates numerous developmental processes. The key enzyme in the two-step biosynthetic pathway of ethylene is 1-aminocyclopropane-1-carboxylate...Full Text Available
2009-11-01
UK PubMed Central (United Kingdom)
Bovine leukemia virus (BLV) is a complex B-lymphotrophic retrovirus of cattle and the causative agent of enzootic bovine leukosis. Serum antibody in infected animals does not correlate with protection...Full Text Available
2000-09-01
Wire pad chamber for LHCb muon system
2000-003 Wire pad chambers (WPC) have been proposed for the outer Region 4 of the LHCb Muon System. These are double gap MWPCs with small wire spacing allowing to obtain 99% detection efficiency in a 20 ns time window. The chambers have a rectangular shape with the vertical dimension from 20 cm in Station 1 to 30 cm in Station 5. The horizontal dimensions will be different with the maximal size of 3 meters in Station 5. The wires are in the vertical direction. The short wire length allows to use small wire spacing needed for high time resolution. Also, this helps to obtain the uniform gas gain over the whole chamber area. The WPC has one row of the wire pads formed by grouping wires in separate readout channels. Four WPC prototypes have been built at PNPI and tested in the PS beam at CERN. Here we report on the results from these tests. Also, the results of simulation of the WPC performance are presented.
2000-01-01
Energy Technology Data Exchange (ETDEWEB)
Previous studies have found that classrooms are often inadequately ventilated, with the resultant increased risk of negative impacts on the pupils. This paper describes a series of field measurements that investigated the indoor air quality, thermal comfort and acoustic performance of nine recently built secondary schools in England. The most significant conclusion is that the complex interaction between ventilation, thermal comfort and acoustics presents considerable challenges for designers. The study showed that while the acoustic standards are demanding it was possible to achieve natural ventilation designs that met the criteria for indoor ambient noise levels when external noise levels were not excessive. Most classrooms in the sample met the requirement of limiting the daily average CO{sub 2} concentration to below 1500 ppm but just a few met the need to readily provide 8 l/s per person of fresh air under the easy control of the occupants. It would seem that the basic requirement ...
2009-07-15
Vibration signature analysis of AFM images
Energy Technology Data Exchange (ETDEWEB)
Vibration signature analysis has been commonly used for the machine condition monitoring and the control of errors. However, it has been rarely employed for the analysis of the precision instruments such as an atomic force microscope (AFM). In this work, an AFM was used to collect vibration data from a sample positioning stage under different suspension and support conditions. Certain structural characteristics of the sample positioning stage show up as a result of the vibration signature analysis of the surface height images measured using an AFM. It is important to understand these vibration characteristics in order to reduce vibrational uncertainty, improve the damping and structural design, and to eliminate the imaging imperfections. The choice of method applied for vibration analysis may affect the results. Two methods, the data dependent systems (DDS) analysis and the Welch`s periodogram averaging method were investigated for application to this problem. Both techniques provide ...
1995-12-31
VAWT performance prediction - Description of a PC-based software
Energy Technology Data Exchange (ETDEWEB)
The Vertical Axis Wind Turbine (VAWT) offers a mechanically and structurally simple method of harnessing the energy of the wind. Fast and accurate predictions of the VAWT performance can be obtained using momentum models. Aerodynamic streamtube models are based on the conservation-of-momentum principle in a quasi-steady flow, by equating the forces of the rotor blades to the change in streamwise momentum through the turbine. An analytical model considering a multi-streamtube system divided into two parts has been developed to determine the aerodynamic blade loads and rotor performance of the Darrieus wind turbine (CARDAA computer code). This so-called double multiple-streamtube (DMS) model uses two constant interference factors in the induced velocities and accounts for vertical variations in the free stream velocity. It has been recently modified to produce an efficient software package appropriate for the needs of VAWT designers. This software called CARDAAV runs under Microsoft ...
1995-12-31
The Hunt for New Physics at the Large Hadron Collider
The Large Hadron Collider presents an unprecedented opportunity to probe the realm of new physics in the TeV region and shed light on some of the core unresolved issues of particle physics. These include the nature of electroweak symmetry breaking, the origin of mass, the possible constituent of cold dark matter, new sources of CP violation needed to explain the baryon excess in the universe, the possible existence of extra gauge groups and extra matter, and importantly the path Nature chooses to resolve the hierarchy problem - is it supersymmetry or extra dimensions. Many models of new physics beyond the standard model contain a hidden sector which can be probed at the LHC. Additionally, the LHC will be a top factory and accurate measurements of the properties of the top and its rare decays will provide a window to new physics. Further, the LHC could shed light on the origin of neutralino masses if the new physics associated with their generation lies in the TeV ...
2010-01-01
Synchronous Averaging for Asynchronous Sampling Data
The progress of digital audio technology enabled the familiar use of the products such as CD and DAT in the acoustic measurement. For example, a signal reproduced with CD player is inputted into a subject of measurement and DAT recorder records its response. However, the sampling cannot be synchronized completely with the input signal although both nominal sample rates are set up equally, because player and recorder work independently. It is the most popular software solution to perform the synchronous addition after converting the recorded signal into the original sampling rate. However, the rate conversion also has the error due to the windowing in the high frequency region of processed signal. This paper proposes a new method for averaging asynchronous sampling data to solve these problems. To evaluate performance, the transfer function of only measuring equipment estimated from asynchronous sampling data was compared with the measuring result in synchronous ...
2005-01-01
Seiberg duality and e+e- experiments
Energy Technology Data Exchange (ETDEWEB)
Seiberg duality in supersymmetric gauge theories is the claim that two different theories describe the same physics in the infrared limit. However, one cannot easily work out physical quantities in strongly coupled theories and hence it has been difficult to compare the physics of the electric and magnetic theories. In order to gain more insight into the equivalence of two theories, we study the ''e{sup +}e{sup -}'' cross sections into ''hadrons'' for both theories in the superconformal window. We describe a technique which allows us to compute the cross sections exactly in the infrared limit. They are indeed equal in the low-energy limit and the equality is guaranteed because of the anomaly matching condition. The ultraviolet behavior of the total ''e{sup +}e{sup -}'' cross section is different for the two theories. We comment on proposed nonsupersymmetric ...
1998-10-02
Renewable energy in the urban setting: Year two
Energy Technology Data Exchange (ETDEWEB)
At the 1996 Conference in North Carolina, The Green Institute began to share its story. Their presentation this year will cover where they are in the design process and their plans for using solar and wind technologies in the development of an Eco-Industrial Park and Business Incubator. Located in a Federal Enterprise Community in Minneapolis, this project borrows sustainable and green building principles using the Rocky Mountain Institute and Solar Living Center as models. Using a change in the paradigm regarding how industry does business, The Green Institute is joining with developments across the country that are putting together Eco-Industrial Parks which use closed loop production systems to reduce waste and emissions generated from manufacturing processes. Using renewable energy, both solar and wind, presents challenges both in the integration of systems on this small site and the educational opportunities with a large potential audience outside the building`s walls and ...
1997-12-31
Radiant flash pyrolysis of biomass as a source of fuels and chemicals
Energy Technology Data Exchange (ETDEWEB)
Last year a team of US and French scientists using the Odeillo (France) 1MW/sub th/ solar furnace showed concentrated solar radiation to be an effective means for rapidly volatilizing biomass materials. The results of continuing research in the U.S. on radiant flash pyrolysis of biomass as a source of fluid fuels, industrial feedstocks and chemicals are described. Bench scale sources of intense, visible radiant energy have been used to simulate the concentrated solar flux available at the focus of solar towers. Windowed transport reactors are being developed, which act as cavity receivers for the focused radiant energy and provide a means for direct use of the radiation to rapidly pyrolyze the entering biomass. One of these reactors will be operated at the focus of the Georgia Tech 400kW/sub th/ solar furnace next August. Preliminary results from the bench scale reactor experiments, and plans for the Georgia Tech experiments are detailed.
1980-01-01
Planar excilamp on rare gas chlorides pumped by a transverse self-sustained discharge
The design and parameters of a UV-VUV spontaneous radiation source - an excilamp operating on chlorides of rare gases ArCl{sup *}, KrCl{sup *} and XeCl{sup *} in the wavelength range 175-308 nm are presented. The Ne-Xe(Kr, Ar)-HCl mixtures were excited by a high-pressure self-sustained discharge with spark preionisation. It is shown that upon pumping mixtures of rare gases and halogens by a transverse discharge, the intensities of the B-X emission band of molecules ArCl{sup *}, KrCl{sup *} and XeCl{sup *} are comparable and up to 90% of the emission energy of excilamps can be concentrated in the UV region. The peak UV power density at 222 and 308 nm on the output window of the excilamp was {approx}2 kW cm{sup -2} for the pulse energy up to {approx} 3 mJ. The output emission energy of the excilamp at 175 nm achieved {approx}0.6 mJ and the peak power density was {approx}0.4 kW cm{sup -2}. (laser applications and other topics in quantum electronics)
2006-02-28
Operating experience with solidification of radioactive waste by a thin-film evaporator
Energy Technology Data Exchange (ETDEWEB)
In the nuclear power stations of GDR the rough radioactive waste includes borat-containing evaporator bottoms and spent ion exchanger resins. For its final disposal in deep geological formations (rock salt mines) this waste has to be solidified. The experience of one year lasting operation of a steam heated thin-film evaporator (heating surface 2 m{sup 3}) for evaporator bottoms to be solidified with a solid content of 200-250 g/l are reported on. In short time such amount of water is abstracted from the rough waste that due to the borate content a hot high-viscous product passes from evaporator to waste drum and there solidifies like glass to monolith. The product quality depends on the adjustment of the flow-equilibrium in the evaporator. Boric acid is used as matrix for the radioactive residues. The residual water content of the solidified waste product was about 15-20%, the volume reduction was V{sub f}=5...6. In order to be sure to get a solidified product a process control was ...
1990-01-01
Operating experience with solidification of radioactive waste by a thin-film evaporator
International Nuclear Information System (INIS)
In the nuclear power stations of GDR the rough radioactive waste includes borat-containing evaporator bottoms and spent ion exchanger resins. For its final disposal in deep geological formations (rock salt mines) this waste has to be solidified. The experience of one year lasting operation of a steam heated thin-film evaporator (heating surface 2 m"3) for evaporator bottoms to be solidified with a solid content of 200-250 g/l are reported on. In short time such amount of water is abstracted from the rough waste that due to the borate content a hot high-viscous product passes from evaporator to waste drum and there solidifies like glass to monolith. The product quality depends on the adjustment of the flow-equilibrium in the evaporator. Boric acid is used as matrix for the radioactive residues. The residual water content of the solidified waste product was about 15-20%, the volume reduction was V_f=5...6. In order to be sure to get a solidified product a process control was achieved by ...
1990-06-01
New horizons of zeolite supported catalysts
International Nuclear Information System (INIS)
This paper reports on the superiority of zeolites over amorphous solids which is well documented for solid acid catalysts of industrial use. Crystalline supports, likewise, open attractive perspectives for catalysis by metals, alloys, and ligated metal clusters. Size and location of clusters can be controlled by careful design of the preparation conditions. Pore dimensions control the access of reactants to active sites and escape paths for products. Cage dimensions determine which transition states can be attained; window apertures are functional in isolating metal clusters from each other, thus preventing ther coalescence and growth. The ship-in-a-bottle method permits deisgn of fairly large active complexes entrapped in zeolite cages. Orientation of non-spherical molecules in a zeolite proe helps to direct their collision with a metal particle to the head on mode; however, isolated Pt atoms hidden in niches of the pore walls can attack passing molecules at their ...
1992-04-05
Nanostructured mesoporous materials for lithium-ion battery applications
The Energy crisis happens to be one of the greatest challenges we are facing today. In this view, much effort has been made in developing new, cost effective, environmentally friendly energy conversion and storage devices. The performance of such devices is fundamentally related to material properties. Hence, innovative materials engineering is important in solving the energy crisis problem. One such innovation in materials engineering is porous materials for energy storage. Porous electrode materials for lithium-ion batteries (LIBs) offer a high degree of electrolyte-electrode wettability, thus enhancing the electrochemical activity within the material. Among the porous materials, mesoporous materials draw special attention, owing to shorter diffusion lengths for Li+ and electronic movement. Nanostructured mesoporous materials also offer better packing density compared to their nanostructured counterparts such as nanopowders, nanowires, nanotubes etc., thus opening a ...
2011-05-01
Measurement of gamma-ray detection efficiency in irradiated materials examination facility
Energy Technology Data Exchange (ETDEWEB)
The detection efficiency of gamma scanning system in irradiated materials examination facility has been measured. Gamma-ray sources used in this experiment are Cs-Co standard sources a PWR spent fuel rod in which {sup 134}Cs and {sup 154}Eu peaks are clearly identified in the energy region of 500 to 1,600 keV. The distance between source and detector is about 1.6 m. A slit type collimator with 3 mm-width window and 30 mm-thick lead block are installed between source and detector. The detector is a HPGe detector. This equipment is mainly used in gamma scanning of irradiated nuclear fuel. The measured detection efficiency seems to be 1.89 x 10{sup -6} % for 1 MeV gamma-ray. With these results the activities of unknown sources could be measured. This results are expected to be used in the measurement of the absolute distribution of gamma emitting nuclides in nuclear fuel.
2001-05-01
Materials considerations for the National Spallation Neutron Source target
Energy Technology Data Exchange (ETDEWEB)
The National Spallation Neutron Source (NSNS), in which neutrons are generated by bombarding a liquid mercury target with 1 GeV protons, will place extraordinary demands on materials performance. The target structural material will operate in an aggressive environment, subject to intense fluxes of high energy protons, neutrons, and other particles, while exposed to liquid mercury and to water. Components that require special consideration include the Hg liquid target container and protective shroud, beam windows, support structures, moderator containers, and beam tubes. In response to these demands a materials R and D program has been developed for the NSNS that includes: selection of materials; calculations of radiation damage; irradiations, post irradiation testing, and characterization; compatibility testing and characterization; design and implementation of a plan for monitoring of materials performance in service; and materials engineering and technical ...
1997-08-01
Energy Technology Data Exchange (ETDEWEB)
Kawasaki Steel has modernized blast furnace control systems featuring an integrated instrumentation and electrical system for each sub-process, a human-machine interface through a single window, and a distributed process computer system. A furnace diagnosis system, which has been known as 'GO-STOP system', has been developed to a knowledge-based system that enables to provide appropriate action guidance. For the burden distribution control, controllability and flexibility have been improved by the use of a bell-less-top charging device. For hot stove control, the automatic setting of a combustion gas flow rate and improved efficiency have been achieved by a fuzzy control system. Furthermore, the remote operation of cast house equipment has been realized and contributed to improve the working environment and the efficient operation at Chiba Works No. 6 blast furnace. (author)
1999-12-01
Indoor thoron and radon concentration measurements with passive cup monitors
International Nuclear Information System (INIS)
A new type of passive integrating cup monitors was developed to measure indoor thoron("2"2"0Rn) and radon("2"2"2Rn) concentrations. By placing a pair of cup monitors with different size a air exchange windows in the same place during a sufficient period of time the concentrations of both gases can be assessed from the alpha track densities on the CN films of the two monitors. The lower detection limit with a 3 months measurement period is for "2"2"0Rn 26.1 Bq*m"-"3 and is for "2"2"2Rn 6.1 Bq*m"-"3. Radon-220 and "2"2"2Rn concentrations have been measured in about 20 different types of dwellings around the Nagoya area with these monitors. The results suggest that the "2"2"0Rn concentrations were rather high in traditional Japanese dwellings made of a timber frame and mud. (orig.). (4 refs., 4 figs.).
1993-07-04
Energy Technology Data Exchange (ETDEWEB)
Ventilation, cooling and illumination of modern high-rise office buildings with high-quality thermal insulation (average k-value 1.0 W/m12K) and high loads from office machinery (up to 20 W/m12 and beyond) are problematic even for modern facility management systems, with consequences for the building shell, heating system, and window ventilation. [Deutsch] Die Lueftung, Kuehlung und Beleuchtung moderner Buerohochbauten mit extremer Waermedaemmung (mittlerer K-Wert 1,0 W/m{sup 2}K) und hohen Bueromaschinenlasten (bis zu 20 W/m{sup 2} und mehr) verursachen auch heute noch erhebliche Probleme, obwohl die technische Gebaeudeausruestung weiterentwickelt wurde. Dies zeigt sich vor allem bei der Fassadenausbildung der Heizung und Fensterlueftung. (orig.)
1999-11-01
Energy Technology Data Exchange (ETDEWEB)
First, attention is paid to the development and use of new construction techniques, including the use of new building materials, e.g. synthetic materials and the so-called steel frame method. Next, the reduction of the energy consumption during the service life of a house is discussed. The reduction can be realized by means of passive methods, e.g. improved windows, thermal insulation and design, or by means of active methods, e.g. electric load monitoring. The information in this article mainly concerns the housing construction in the USA and Canada. The purpose of this article to contribute to the discussion in the Netherlands on innovation in the building technology, e.g. formulated in the report `Bouwvisie 2010` (Vision on Buildings for the year 2010) of the Dutch Advisory Board Technology Policy for the Building Industry (ARTB, abbreviated in Dutch) and the building technology policy of the Dutch Ministry of Economic Affairs (EZ). 4 figs., 2 tabs., 23 refs.
1996-12-31
Energy Technology Data Exchange (ETDEWEB)
Transduction method developed by the research coordinator and Prof. Muroga is one of the most popular methods to design large-scale integrated circuits, and thus used by major design tool companies in USA and Japan. The major objectives of the research is to improve capability and utilize its reusable property by combining with CAD databases. Major results of the project is as follows, (1) Improvement of Transduction method : Efficiency, capability and the maximum circuit size are improved. Error compensation method is also improved. (2) Applications to new logic elements : Transduction method is modified to cope with wired logic and FPGAs. (3) CAD databases : One of the major advantages of Transduction methods is 'reusability' of already designed circuits. It is suitable to combine with CAD databases. We design CAD databases suitable for cooperative design using Transduction method. (4) Program development : Programs for Windows95 and developed ...
1997-03-01
FEA Analysis of AP-0 Target Hall Collection Lens (Current Design)
Energy Technology Data Exchange (ETDEWEB)
The AP-0 Target Hall Collection Lens is a pulsed device which focuses anti-protons just downstream of the Target. Since the angles at which the anti-protons depart the Target can be quite large, a very high focusing strength is required to maximize anti-proton capture into the downstream Debuncher Ring. The current design of the Collection Lens was designed to operate with a focusing gradient of 1,000 T/m. However, multiple failures of early devices resulted in lowering the normal operating gradient to about 750 T/m. At this gradient, the Lens design fares much better, lasting several million pulses, but ultimately still fails. A Finite Element Analysis (FEA) has been performed on this Collection Lens design to help determine the cause and/or nature of the failures. The Collection Lens magnetic field is created by passing high current through a central conductor cylinder. A uniform current distribution through the cylinder will create a tangential or azimuthal magnetic field that ...
2001-06-22
Equation of state of laser-shocked compressed iron; Equation d'etat du fer comprime par choc laser
Energy Technology Data Exchange (ETDEWEB)
This thesis enters the field of highly compressed materials equation of state studies. In particular, it focuses on the case of laser shock compressed iron. This work indeed aims at getting to the conditions of the earth's core, comprising a solid inner core and a liquid outer core. The understanding of phenomena governing the core's thermodynamics and the geodynamic process requires the knowledge of iron melting line locus around the solid-liquid interface at 3.3 Mbar. Several experiments were performed to that extent. First, an absolute measurement of iron Hugoniot was obtained. Following is a study of partially released states of iron into a window material: lithium fluoride (LiF). This configuration enables direct access to compressed iron optical properties such as reflectivity and self-emission. Interface velocity measurement is dominated by compressed LiF optical properties and is used as a pressure gauge. Using a dual wavelength ...
2004-01-01
material, and that these magnetic properties vary systematically with the diameter of the spherical pores within the films. A new oscillation effect has been observed for the coercivity of macroporous Ni sub 8 sub 0 Fe sub 2 sub 0 film with different pore layer thickness. sphere templates, the resulting films show well-formed, regular, two- and three-dimensional macroporous networks consisting of spherical pores arranged in a highly ordered face centred cubic (fee) structure. The spherical voids are interconnected by a series of smaller windows that form an open porous structure embedded in the material framework. The diameter of the spherical pores can be precisely changed over the range from 200 to 1000 nm by changing the diameter of the latex spheres used to form the templates. The resulting macroporous material structures are robust, self-supported, dense, polycrystalline, uniform and free from filling defects and contamination or problems caused by shrinkage ...
2002-01-01
Energy Technology Data Exchange (ETDEWEB)
Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The precipitates at metal-oxide interface could act not only as cathodic sites in the anodic protection mechanism but also ...
2000-08-01
International Nuclear Information System (INIS)
Substantial roles of precipitates such as Zr-Fe-Cr type intermetallic compounds on uniform corrosion and hydrogen pickup of zirconium alloys in pure water autoclave tests were investigated from an electrochemical point of view. In the previous paper, corrosion mechanism was elucidated by the anodic protection-precipitates degradation model. This paper describes the roles on hydrogen pickup. 633 K pure water autoclave test was performed on high purity zirconium, Zr-0.2Fe, Zr-0.2Cr, and Zr-0.1Fe-0.1Cr alloys. Hydrogen analysis after the corrosion test showed that hydrogen pickup ratio of Zr-0.2Fe alloy was about 80%. It was much higher than about 30% of pure Zr and about 10% of both Zr-0.2Cr and Zr-0.1Fe-0.1Cr alloys. Larger hydrogen content was introduced into Zr-0.2Fe alloy than the other ones by the cathodic hydrogen charging under coulombic equivalence. The precipitates at metal-oxide interface could act not only as cathodic sites in the anodic protection mechanism but also ...
2000-08-01
Energy Technology Data Exchange (ETDEWEB)
Thermal, electrical, and electrochemical properties were investigated for the (100-x)(0.6Li{sub 2}S{center{underscore}dot}0.4SiS{sub 2}){center{underscore}dot}xLi{sub 4}SiO{sub 4} oxysulfide glasses. The glass with x = 5 exhibited high electrical conductivity of about 10{sup {minus}3} S cm{sup {minus}1} at room temperature, high glass stability against crystallization, and good chemical stability in contact with Li metal. Cyclic voltammetry also suggested that this glass has a wide electrochemical window of more than 10 V. On the other hand, further addition of Li{sub 4}SiO{sub 4} up to 20 mol% lowered the conductivity, glass stability against crystallization, and electrochemical stability for the oxysulfide glasses.
1999-09-01
International Nuclear Information System (INIS)
Single crystals of semi-organic L-histidine hydrobromide have been grown by slow evaporation technique from a mixture of L-histidine and hydrobromic acid in aqueous solution at ambient temperature. From high-resolution X-ray diffraction analysis, the crystalline perfection of the grown crystal has been studied. Single crystal X-ray diffraction analyses, Nuclear Magnetic Resonance spectral analysis, Thermo-Gravimetry (TG), Differential Thermal Analysis (DTA) and hardness test have been employed to characterize the as-grown crystals. The UV cutoff wavelength of the grown crystal is below 300 nm and has a wide transparency window, which is suitable for second harmonic generation of laser in the blue region. Nonlinear optical characteristics have been studied using Q switched Nd:YAG laser (#lambda#=1064 nm). The second harmonic generation conversion efficiency of the grown crystals confirms their suitability for frequency conversion applications.
2010-12-15
British Library Electronic Table of Contents (United Kingdom)
This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen and carbon black (CB) as a high-value nano-material with the bonus of zero CO2 emission. The work focused on the development of a medium-scale solar reactor (10kW) based on the indirect heating concept. The solar reactor is composed of a cubic cavity receiver (20cm-side), which absorbs concentrated solar irradiation through a quartz window by a 9cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results in the temperature range 1740-2070K are presented: acetylene (C2H2) was the most important by-product with a mole fraction of up to about 7%, depending on the gas residence time. C2H2 content i...
2011-01-01
Clinical-HINTS: integrated intelligent ICU patient monitoring and information management system.
Clinical-HINTS (Health Intelligence System) is a horizontally integrated decision support system (DSS) designed to meet the requirements for intelligent real-time clinical information management in critical care medical environments and to lay the foundation for the development of the next generation of intelligent medical instrumentation. The system presented was developed to refine and complement the information yielded by clinical laboratory investigations, thereby benefiting the management of the intensive care unit (ICU) patient. More specifically, Clinical-HINTS was developed to provide computer-based assistance with the acquisition, organisation and display, storage and retrieval, communication and generation of real-time patient-specific clinical information in an ICU. Clinical-HINTS is an object-oriented system developed in C+2 to run under Microsoft Windows as an embryo intelligent agent. Current generic reasoning skills include perception and reactive ...
1997-01-01
Camera for coherent diffractive imaging and holography with a soft-x-ray free-electron laser
International Nuclear Information System (INIS)
We describe a camera to record coherent scattering patterns with a soft-x-ray free-electron laser (FEL). The camera consists of a laterally graded multilayer mirror, which reflects the diffraction pattern onto a CCD detector. The mirror acts as a bandpass filter for both the wavelength and the angle, which isolates the desired scattering pattern from nonsample scattering or incoherent emission from the sample. The mirror also solves the particular problem of the extreme intensity of the FEL pulses, which are focused to greater than 10"1"4 W/cm"2. The strong undiffracted pulse passes through a hole in the mirror and propagates onto a beam dump at a distance behind the instrument rather than interacting with a beam stop placed near the CCD. The camera concept is extendable for the full range of the fundamental wavelength of the free electron laser in Hamburg (FLASH) FEL (i.e., between 6 and 60 nm) and into the water window. We have fabricated and tested various ...
2008-04-01
Applications with a new low-temperature UHV STM at 5 K
International Nuclear Information System (INIS)
A new dedicated UHV STM for investigations at T#<=#5 K is presented. To achieve such low temperatures and to ensure a high thermal stability, the low-temperature (LT) STM described here has a concentric system of bath cryostats. There are openings for tip and sample exchange at low T, and windows with an infrared radiation shield for optical access, which can both be closed by a door mechanism for LT-STM measurements. Efficient vibration isolation is realized by using spring suspension with eddy current damping. With the 3-d coarse positioning unit any region of interest within 5 mm by 5 mm on the sample is accessible even at 5 K. For short turn-around cycles the sample and tip can both be exchanged at low temperatures. Atomically resolved images of Au(111) at 5 K in UHV demonstrate the excellent performance of this LT STM. As a typical application example the appearance of a charge-density wave on NbSe_2, which occurs below a transition temperature of 33.5 K, ...
1998-03-01
An Empirical Analysis of Internet Protocol Version 6 (IPv6)
Although the current Internet Protocol known as IPv4 has served its purpose for over 20 years, its days are numbered. With IPv6 reaching a mature enough level, there is a need to evaluate the performance benefits or drawbacks that the new IPv6 protocol will have in comparison to the well established IPv4 protocol. Theoretically, the overhead between the two different protocols should be directly proportional to the difference in the packet's header size, however according to our findings, the empirical performance difference between IPv4 and IPv6, especially when the transition mechanisms are taken into consideration, is much larger than anticipated. We first examine the performance of each protocol independently. We then examined two transition mechanisms which perform the encapsulation at various points in the network: host-to-host and router-to-router (tunneling). Our experiments were conducted using two dual stack (IPv4/IPv6) routers using end nodes running both ...
2004-01-01
Aluminum assisted electrodeposition of europium in LiCl-KCl molten salt
Energy Technology Data Exchange (ETDEWEB)
Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu{sup 2+} and Al{sup 3+} at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al{sup 3+} than that of Eu{sup 2+} and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag{sup +} while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag{sup +}, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be extended to -2.43 V vs. Ag|Ag{sup +}. The EDS analysis indicated that AlEu can be deposited at the potential ...
2010-03-01
Aluminum assisted electrodeposition of europium in LiCl-KCl molten salt
International Nuclear Information System (INIS)
Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu2+ and Al3+ at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al3+ than that of Eu2+ and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag+ while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag+, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be extended to -2.43 V vs. Ag|Ag+. The EDS analysis indicated that AlEu can be deposited at the potential more negative than -2.37 V.
2010-03-01
Energy Technology Data Exchange (ETDEWEB)
Lithium ion batteries use an oxide as a positive electrode and a carbon material as a negative electrode. The performances of carbon electrodes have rapidly evolved during the last years thanks to the substitution of soft carbons of Conoco or MCMB-2510 type by graphites (F-399, MCMB-2528) and then by hard carbons. These high capacity carbons (700 mAh/g) have higher service life and volume capacity than graphites but their irreversible losses are greater (>20%). In this work, materials with similar electrochemical performances are prepared by mechanical crushing. Mechanical crushing allows to obtain a wide range of carbon materials with various morphologies, specific surfaces and levels of disorder. The formation of the passivation film is directly linked with the surface of materials. A reaction scheme of the reversible and irreversible capacities has been defined and has permitted to obtain compounds with reversible capacities of 720 mAh/g (2 lithium for 6 carbon). (J.S.)
1996-12-31
The structure of myostatin:follistatin 288: insights into receptor utilization and heparin binding
Myostatin is a member of the transforming growth factor-{beta} (TGF-{beta}) family and a strong negative regulator of muscle growth. Here, we present the crystal structure of myostatin in complex with the antagonist follistatin 288 (Fst288). We find that the prehelix region of myostatin very closely resembles that of TGF-{beta} class members and that this region alone can be swapped into activin A to confer signalling through the non-canonical type I receptor Alk5. Furthermore, the N-terminal domain of Fst288 undergoes conformational rearrangements to bind myostatin and likely acts as a site of specificity for the antagonist. In addition, a unique continuous electropositive surface is created when myostatin binds Fst288, which significantly increases the affinity for heparin. This translates into stronger interactions with the cell surface and enhanced myostatin degradation in the presence of either Fst288 or Fst315. Overall, we have identified several ...
2009-09-29
The nucleon interaction and neutron matter from the renormalization group
We show that the renormalization group decimation of modern nucleon potential models to low momenta results in a unique nucleon interaction V_{low k}. This interaction is free of short-ranged singularities and can be used directly in many-body calculations. The RG scaling properties follow directly from the invariance of the scattering phase shifts. We discuss the RG treatment of Fermi liquids. The RG equation for the scattering amplitude in the two particle-hole channels is given at zero temperature. The flow equations are simplified by retaining only the leading term in an expansion in small momentum transfers. The RG flow is illustrated by first studying a system of spin-polarized fermions in a simple model. Finally, results for neutron matter are presented by employing the unique low momentum interaction V_{low k} as initial condition of the flow. The RG approach yields the amplitude for non-forward scattering, which is of great interest ...
2002-01-01
The chemistry of hydrothermal mounds near the Galapagos Rift
Samples dredged from the sediment mounds have a unique chemistry and mineralogy which reveals details of the hydrothermal processes that produce these deposits. The mounds form primarily by deposition of Fe, Mn and Si from hydrothermal fluids which circulate through the basalt crust and the overlying sediments. The Mn, Fe and Si are strongly fractionated in the process; the Fe and Si precipitate within the mounds under slightly reducing conditions as nontronite, while the Mn is deposited as Mn oxyhydroxides at the seawater-sediment interface. The nontronite is exceptionally well crystallized, and contains less than 200 ppm Al. The Mn minerals, todorokite and birnessite, also have exceptional crystallinity and the distribution of trace elements Cu, Ni, Zn, Co, Ca and Ba in these phases agrees with predictions made on the basis of models of their crystal structure. The environment of deposition which produces this suite of minerals - slow percolation of hydrothermal ...
1978-06-01
The automatic programming for safety-critical software in nuclear power plants
Energy Technology Data Exchange (ETDEWEB)
We defined the Korean unique safety-critical software development methodology by modifying Dr. Harel`s statechart-based on formal methods in order to digitalized the reactor protection system. It is suggested software requirement specification guideline to specify design specification which is basis for requirement specification and automatic programming by the caused by shutdown parameter logic of the steam generator water level for Wolsung 2/3/4 unit SDS no.1 and simulated it by binding the Graphic User Interface (GUI). We generated the K and R C code automatically by utilizing the Statemate MAGNUM Sharpshooter/C code generator. Auto-generated K and R C code is machine independent code and has high productivity, quality and provability. The following are the summaries of major research and development. - Set up the Korean unique safety-critical software development methodology - Developed software requirement specification guidelines - ...
1998-06-01
Rearrangement of a common cellular DNA domain on chromosome 4 in human primary liver tumors
Energy Technology Data Exchange (ETDEWEB)
Hepatitis B virus (HBV) DNA integration has been shown to occur frequently in human hepatocellular carcinomas. The authors have investigated whether common cellular DNA domains might be rearranged, possibly by HBV integration, in human primary liver tumors. Unique cellular DNA sequences adjacent to an HBV integration site were isolated from a patient with hepatitis B surface antigen-positive hepatocellular carcinoma. These probes detected rearrangement of this cellular region of chromosomal DNA in 3 of 50 additional primary liver tumors studied. Of these three tumor samples, two contained HBV DNA, without an apparent link between the viral DNA and the rearranged allele; HBV DNA sequences were not detected in the third tumor sample. By use of a panel of somatic cell hybrids, these unique cellular DNA sequences were shown to be located on chromosome 4. Therefore, this region of chromosomal DNA might be implicated in the formation of different ...
1988-02-01
Rearrangement of a common cellular DNA domain on chromosome 4 in human primary liver tumors
International Nuclear Information System (INIS)
Hepatitis B virus (HBV) DNA integration has been shown to occur frequently in human hepatocellular carcinomas. The authors have investigated whether common cellular DNA domains might be rearranged, possibly by HBV integration, in human primary liver tumors. Unique cellular DNA sequences adjacent to an HBV integration site were isolated from a patient with hepatitis B surface antigen-positive hepatocellular carcinoma. These probes detected rearrangement of this cellular region of chromosomal DNA in 3 of 50 additional primary liver tumors studied. Of these three tumor samples, two contained HBV DNA, without an apparent link between the viral DNA and the rearranged allele; HBV DNA sequences were not detected in the third tumor sample. By use of a panel of somatic cell hybrids, these unique cellular DNA sequences were shown to be located on chromosome 4. Therefore, this region of chromosomal DNA might be implicated in the formation of different ...
NMR studies of Borrelia burgdorferi OspA, a 28 kDa protein containing a single-layer #beta#-sheet
International Nuclear Information System (INIS)
The crystal structure of outer surface protein A (OspA) from Borrelia burgdorferi contains a single-layer #beta#-sheet connecting the N- and C-terminal globular domains. The central #beta#-sheet consists largely of polar amino acids and it is solvent-exposed on both faces, which so far appears to be unique among known protein structures. We have accomplished nearly complete backbone H, C and N and C";/H"#beta# assignments of OspA (28 kDa) using standard triple resonance techniques without perdeuteration. This was made possible by recording spectra at a high temperature (45 "oC ). The chemical shift index and "1"5N T_1/T_2 ratios show that both the secondary structure and the global conformation of OspA in solution are similar to the crystal structure, suggesting that the unique central #beta#-sheet is fairly rigid.
1998-05-01
Multiple-element eddy current probes for enhanced inspection
Energy Technology Data Exchange (ETDEWEB)
Eddy current inspection methods are widely used for the nondestructive evaluation (NDE) of tubular products. Specifically, the sensors and instrumentation are designed to detect and characterize changes in a material's electrical and magnetic properties produced by the presence of discontinuities. A recent major enhancement in eddy current inspection technology has been the development of computer interfacing for data collection, analysis, and display. This breakthrough has led to multiple-frequency testing, eddy current imaging, and automated data interpretation systems that significantly enhance both capabilities and reliability of the eddy current inspection. In addition to the clear advantages in data processing, computer interfacing also permits the design and creation of unique sensors that further enhance eddy current inspection capabilities. Perhaps the most promising area of computer interactive probe design is multiple element sensors. ...
1993-07-01
Microscopic analysis of the /sup 88/Sr(p,p') reaction at E/sub p/ = 201. 5 MeV
Energy Technology Data Exchange (ETDEWEB)
Differential cross sections for 201.5 MeV proton scattering form /sup 88/Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good description is ...
1988-04-25
Microscopic analysis of the "8"8Sr(p,p') reaction at E_p = 201.5 MeV
International Nuclear Information System (INIS)
Differential cross sections for 201.5 MeV proton scattering form "8"8Sr were measured. From the analysis of the elastic data, no unique optical-model potential could be obtained, but the radial moments are well determined. In a macroscopic analysis of the collective states it turns out that if the optical potential and transition potential are chosen consistently, unambiguous potential deformation lengths can be obtained even though the optical potential is not unique. Taking into account the range and density dependence of the underlying effective interaction reliable neutron deformation lengths can be obtained. For inelastic transitions of various character microscopic distorted-wave calculations with a density-dependent interaction based on the Paris potential were performed. The nuclear structure was taken from one broken-pair calculations in a large model space, calibrated by (e,e') data. In general a good description is obtained for ...
Materials needs for compact fusion reactors
Energy Technology Data Exchange (ETDEWEB)
The economic prospects for magnetic fusion energy can be dramatically improved if for the same total power output the fusion neutron first-wall (FW) loading and the system power density can be increased by factors of 3 to 5 and 10 to 30, respectively. A number of compact fusion reactor embodiments have been proposed, all of which would operate with increased FW loadings, would use thin (0.5 to 0.6 m) blankets, and would confine quasi-steady-state plasma with resistive, water-cooled copper or aluminum coils. Increased system power density (5 to 15 MWt/m/sup 3/ versus 0.3 to 0.5 MW/m/sup 3/), considerably reduced physical size of the fusion power core (FPC), and appreciably reduced economic leverage exerted by the FPC and associated physics result. The unique materials requirements anticipated for these compact reactors are outlined against the well documented backdrop provided by similar needs for the mainline approaches. Surprisingly, no single materials need that ...
1983-01-01
Half-trek criterion for generic identifiability of linear structural equation models
A linear structural equation model relates random variables of interest and corresponding Gaussian noise terms via a linear equation system. Each such model can be represented by a mixed graph in which directed edges encode the linear equations, and bidirected edges indicate possible correlations among noise terms. We study parameter identifiability in these models, that is, we ask for conditions that ensure that the edge coefficients and correlations appearing in a linear structural equation model can be uniquely recovered from the covariance matrix of the associated normal distribution. We treat the case of generic identifiability, where unique recovery is possible for almost every choice of parameters. We give a new graphical criterion that is sufficient for generic identifiability. It improves criteria from prior work and does not require the directed part of the graph to be acyclic. We also develop a related necessary condition and examine ...
2011-01-01
ELMO Bumpy Torus Reactor and power plant: conceptual design study
International Nuclear Information System (INIS)
A complete power plant design of a 1200-MWe ELMO Bumpy Torus Reactor (EBTR) is presented. An emphasis is placed on those features that are unique to the EBT confinement concept, with subsystems and balance-of-plant items that are more generic to magnetic fusion being adapted from past, more extensive tokamak reactor designs. Similar to the latter tokamak studies, this conceptual EBTR design also emphasizes the use of conventional or near state-of-the-art engineering technology and materials. An emphasis is also placed on system accessibility, reliability, and maintainability, as these crucial and desirable characteristics relate to the unique high-aspect-ratio configuration of EBTs. Equal and strong emphasis is given to physics, engineering/technology, and costing/economics components of this design effort. Parametric optimizations and sensitivity studies, using cost-of-electricity as an object function, are reported. Based on these results, ...
1988-10-09
Cleanup at Los Alamos National Laboratory - the challenges - 9493
Energy Technology Data Exchange (ETDEWEB)
This paper provides an overview of environmental cleanup at the Los Alamos National Laboratory (LANL) and some of the unique aspects and challenges. Cleanup of the 65-year old Department of Energy Laboratory is being conducted under a RCRA Consent Order with the State of New Mexico. This agreement is one of the most recent cleanup agreements signed in the DOE complex and was based on lessons learned at other DOE sites. A number of attributes create unique challenges for LANL cleanup -- the proximity to the community and pueblos, the site's topography and geology, and the nature of LANL's on-going missions. This overview paper will set the stage for other papers in this session, including papers that present: Plans to retrieve buried waste at Material Disposal Area B, across the street from oen of Los Alamos' commercial districts and the local newspaper; Progress to date and joint plans with WIPP for disposal of the ...
2008-01-01
Behavioural evidence for mental time travel in nonhuman animals.
If episodic memory is an adaptation, it must have evolved to benefit present or future survival and reproduction, rather than to provide an accurate record of the past per se. Recent research has documented various links between the ability to construct episodes of the past and imagine potential future episodes, and it has been argued that the former may be a design feature of the latter. Thus, claims about the existence of episodic memory in non-verbal organisms may be evaluated by examining behavioural evidence for foresight. Here we review recent data on foresight in animals and conclude that the evidence to suggest episodic memory so far is equivocal. We suggest specific experimental criteria that could provide stronger evidence. We maintain that there must be uniquely human traits for which there are no animal models and it remains possible that mental time travel depends on several such traits. Identification of what precisely is unique ...
2009-12-03
Assembly of Linear Nano-Chains from Iron Oxide Nanospheres with Asymmetric Surface Chemistry
Besides the multifunctionality, another equally important aspect of nanoparticles is their engineerability to control the geometrical and chemical properties during fabrication. In this work, we exploited this aspect to define asymmetric surface chemistry of an iron oxide nanosphere by controlling the topology of ligand expression on its surface resulting in a particle with two faces, one displaying only amines and the other only thiols. Specifically, amine-functionalized iron oxide nanospheres were attached on a solid support via a crosslinker containing a disulfide bridge. Liberation of the nanosphere using thiolytic cleavage created thiols on the portion of the particle's surface that interacted with the solid support. Employing a solid-phase strategy and a step-by-step addition of particles, the two unique faces on the same nanosphere served as fittings to assemble them into linear nano-chains. Assembly of chains with various lengths and aspect ratios was ...
2011-01-06
Energy Technology Data Exchange (ETDEWEB)
The overall objective of this project has been to develop immunochemical methods to quantitate unique DNA base damages in order to facilitate studies on radiation-induced damage production and repair. Specifically, we have been using antibodies raised to damaged bases to quantitate unique lesions in model systems in order to evaluate their potential biological consequences. Our approach has been to synthesize modified nucleotides or nucleosides, conjugate them to protein carriers, and use the conjugates as immunogens in rabbits or to prepare monoclonal antibodies. We have been studying damages that are stable radiolysis products found in X-irradiated DNA and thus of potential biological consequence. Our aim is to build an in vitro and in vivo data base on the interactions between model DNA lesions and such cellular enzymes as DNA polymerases and repair endonucleases. Initial studies have focused on pyrimidine ring saturation products (thymine ...
1992-05-01
An immunochemical approach to the study of DNA damage and repair
Energy Technology Data Exchange (ETDEWEB)
The overall objective of this project has been to develop immunochemical methods to quantitate unique DNA base damages in order to facilitate studies on radiation-induced damage production and repair. Specifically, we have been using antibodies raised to damaged bases to quantitate unique lesions in model systems in order to evaluate their potential biological consequences. Our approach has been to synthesize modified nucleotides or nucleosides, conjugate them to protein carriers, and use the conjugates as immunogens in rabbits or to prepare monoclonal antibodies. We have been studying damages that are stable radiolysis products found in X-irradiated DNA and thus of potential biological consequence. Our aim is to build an in vitro and in vivo data base on the interactions between model DNA lesions and such cellular enzymes as DNA polymerases and repair endonucleases. Initial studies have focused on pyrimidine ring saturation products (thymine ...
1992-05-01
United States Department of Energy breeder reactor staff training domestic program
Energy Technology Data Exchange (ETDEWEB)
Two US DOE projects in the Pacific Northwest offer unique on-the-scene training opportunities at sodium-cooled fast-reactor plants: the Fast Flux Test Facility (FFTF) near Richland, Washington, which has operated successfully in a wide range of irradiation test programs since 1980; and the Experimental Breeder Reactor II (EBR-II) near Idaho Falls, Idaho, which has been in operation for approximately 20 years. Training programs have been especially designed to take advantage of this plant experience. Available courses are described.
1984-01-01
United States Air Force Academy (USAFA) Vertical Axis Wind Turbine. Final report May 77-Sep 80
This report describes the design, fabrication, installation and testing of a small variable-speed vertical axis wind turbine (VAWT). This VAWT is unique in its installation using hand tools only; unconventional and simple support system; and variable speed operation under microprocessor control. Initial testing confirmed that the turbine can be controlled by commanded alternator field modulation. Further studies will be directed toward determination of an optimum control algorithm.
1980-09-01
Towards Antihydrogen Trapping and Spectroscopy at ALPHA
Spectroscopy of antihydrogen has the potential to yield high-precision tests of the CPT theorem and shed light on the matter-antimatter imbalance in the Universe. The ALPHA antihydrogen trap at CERN's Antiproton Decelerator aims to prepare a sample of antihydrogen atoms confined in an octupole-based Ioffe trap and to measure the frequency of several atomic transitions. We describe our techniques to directly measure the antiproton temperature and a new technique to cool them to below 10 K. We also show how our unique position-sensitive annihilation detector provides us with a highly sensitive method of identifying antiproton annihilations and effectively rejecting the cosmic-ray background.
2011-01-01
The relationships of carbon dioxide emissions and income in a newly industrialized economy
British Library Electronic Table of Contents (United Kingdom)
This study investigates the carbon dioxide (CO2) emissions patterns in coordination with the economic development of Taiwan. The resulting quadratic relationship between emissions and income are partly due to the structural change of energy supply in Taiwan, with the introduction of nuclear energy in 1980 to 1986. This relationship is quite unique and different from the N-shaped relationships in some developed countries (de Bruyn and Opschoor, 1997; Friedl and Getzner, 2003). The CO2 emissions in Taiwan increase with the increasing imports of raw materials for economic activities and the increasing use of electricity. There is no evidence that the substantial increase of Taiwan's service sector contributed to slowing its CO2 emissions.
2012-01-01
The inventor?s role: was Schumpeter right?
British Library Electronic Table of Contents (United Kingdom)
According to Schumpeter, the creative process of economic development can be divided into the stages of invention, innovation (commercialization) and imitation. Each stage is associated with specific skills. This paper examines whether Schumpeter?s assertion was correct, i.e. whether the invention and innovation stages should be undertaken by different agents. In addition, we examine whether there is a rationale for the Schumpeterian entrepreneur to include the inventor in the commercialization process. Combining the abilities of the entrepreneur and the inventor may serve to facilitate customer adaptation, strengthen knowledge transfers and reduce uncertainty, thereby expanding market opportunities. Based on a unique database covering Swedish patents granted to individuals and small firms...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
Purpose - The purpose of this research is to investigate the influence of psychological contracts on the adjustment and organisational commitment of expatriates during international business assignments. The study also aims to investigate the influence of psychological barriers to expatriate adjustment. Design/methodology/approach - A unique survey questionnaire was developed to collect data from 219 Taiwanese business expatriates during the first quarter of 2007. A LISREL analysis is used to test the hypotheses of the research framework. Findings - The study finds that: perceived fulfilment of the psychological contracts of expatriates significantly influences both their adjustment to foreign situations and their organisational commitment; psychological barriers to adjustment have a negat...
2009-01-01
The effect of temperature and flow stress for climb-controlled dislocation creep in magnesium alloy
Energy Technology Data Exchange (ETDEWEB)
Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)
2003-07-01
The Proton structure function F(2) in the resonance region
Energy Technology Data Exchange (ETDEWEB)
Unique measurement of the proton structure function F2 in a wide two-dimensional region of x and Q**2 has been reported. The accessible kinematics covers entire resonance region up to W=2.5 GeV in the Q**2 interval from 0.1 to 4.5 GeV**2. Obtained data allowed for the first time an evaluation of moments of the structure function F2 directly from experimental data as well as an intensive study of the Bloom-Gilman duality phenomenon.
2003-06-01
Energy Technology Data Exchange (ETDEWEB)
Surface doping of conjugated polymers is realized by depositing a thin layer of graphene oxide (GO) on top of the polymers. The high proton density and the unique 2D structure of GO facilitate the protonic surface doping of conjugated polymers to achieve high conductivities. This finding represents a new strategy for improving charge transport across the metal/conjugated polymer interface to achieve much improved performance in organic solar cells. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)
2011-04-26
Study of physical properties of protons and "1"2C ions in medical application
International Nuclear Information System (INIS)
Depending on their unique physical properties, proton and heavy ions have taken an irreplaceable role in modern means of tumor treatment. One-step process and two-step process physical models were employed to explain the mechanism of ion energy loss. The transport process of proton and "1"2C in water was simulated by Geant4 toolkit to study the physical properties of ion beam. The calculation results were discussed, which showed the advantages and disadvantages of proton and "1"2C in the medical application. (authors)
2009-06-01
Stimulated radiation of high - current relativistic electron beams
International Nuclear Information System (INIS)
The most propagated mechanisms of stimulated radiation of electron beam such as Cherenkov one-particle and collective effects, ondulator and magnetic bremsshrahlung radiations, Doppler anomalous effect, Thompson and Raman scattering and radiation are discussed. Relation of spontaneous radiation mechanisms of individual electron and stimulated radiation effects in electron beams has been elucidated, grounds of linear electrodynamics of radiative beam instabilities are stated, and main mechanisms of their nonlinear stabilization are elucidated as well. Various simulated processes in electron beams are considered from the unique point of view using a simple mathematical apparatus and such physical laws as conservation and Newton laws.
1987-01-01
States Which Are Equivalent To A Depolarized Pure State
The Schmidt decomposition is an important tool in the study of quantum systems especially for the quantification of the entanglement of pure states. However, the Schmidt decomposition is only unique for bipartite pure states, and {\\it some} multipartite pure states. Here a generalized Schmidt decomposition is given for a class of mixed quantum states. It is shown that it shares some desirable properties with its pure-state counterpart, but lacks some properties which make the pure-state decomposition so important. Experimental methods for the identification of this class of mixed states are provided and some examples are discussed which show the utility of this description.
2007-01-01
Sol-gel approaches for solid electrolytes and electrode materials. Technical report
Energy Technology Data Exchange (ETDEWEB)
Sol-gel chemistry has a great many potential applications in the preparation of unique electrochemical materials, from non-equilibrium transition metal oxides which may be of use as high energy density electrodes, to high-surface area mixed oxides which may possess high proton conductivity, to novel composite structures consisting of inorganic gels in combination with organic, electronic, and ionic conductors. This paper reviews prior work on proton conduction in gel systems and presents recent work regarding electrode materials prepared by sol-gel methods and inorganic-organic materials.
1995-07-14
Simplified RF power system for Wideroe-type linacs
Energy Technology Data Exchange (ETDEWEB)
The RF system for the SuperHILAC injector linac was designed and constructed for minimum system complexity, wide dynamic range, and ease of maintenance. The final amplifier is close coupled to the linac and operates in an efficient semilinear mode, eliminating troublesome transmission lines, modulators, and high level regulators. The system has been operated at over 250 kW, 23 MHz with good regulation. The low level RF electronics are contained in a single chassis adjacent to the RF control computer, which monitors all important operating parameters. A unique 360/sup 0/ phase and amplitude modular is used for precise control and regulation of the accelerating voltage.
1981-03-01
Selective mining of bedded uranium deposits using high-pressure waterjet equipment
International Nuclear Information System (INIS)
High-pressure waterjet equipment is now technically and economically viable and commercially available for the following mining and construction applications: (1) drilling soft to medium-hard rock; (2) slotting, discing, chambering, and reaming in all types of rock. However, additional field experience is needed to prepare detailed economic evaluations. Extensive development of new explosives techniques and blasting methods will be required to take full advantage of the unique waterjet hole slotting, discing, and chambering capabilities.
1981-12-04
Review of the Vortec soil remediation demonstration program
Energy Technology Data Exchange (ETDEWEB)
The DOE`s clean-up of its nuclear complex require the development of innovative technologies to convert soils contaminated by hazardous and/or radioactive wastes to forms which can be readily disposed in accordance with current waste disposal methods. The unique features of Votec CMS technology should make it particularly cost-effective process for the vitrification of soils, sediments, sludges, and mill tailings containing organic metallic and/or radioactive contaminants. This article describes the technology (Votec`s combustion and melting system), the results of testing, the demonstration plant system, and summarizes the future schedule and the equipment needed. 3 figs., 3 tabs.
1994-11-01
Remote sensing of the atmosphere by resonance Raman LIDAR
Energy Technology Data Exchange (ETDEWEB)
When in resonance, Raman scattering exhibits strong enhancement ranging from four to six orders of magnitude. This physical phenomenon has been applied to remote sensing of the Earth`s atmosphere. With a 16 inch Cassegrain telescope and spectrometer/ CCD-detector system, 70-150 ppm-m of SO{sub 2} in the atmosphere has been detected at a distance of 0.5 kilometer. This system can be used to detect/monitor chemical effluence in the atmosphere by their unique Raman fingerprints. Experimental result together with detailed resonance Raman and atmospheric laser propagation effects will be discussed.
1994-12-01
Procyon 1. First prototype worldwide for storage spent nuclear fuel rods
International Nuclear Information System (INIS)
HFH Herbst has designed and built a unique machine for storage of spent highly radioactive nuclear fuel rods within two years for the Swedish SKB. The vehicle (total weight 98 t) can be operated underground without a driver. Herbst was able to bring to this project almost 30 years of experience in the complementation of vehicle projects for the nuclear industry. The Procyon 1 already proved its efficiency impressively in several hundred storage processes and operates with absolute reliability. (orig.)
2010-05-01
PBAR: A superconducting magnet spectrometer for cosmic ray antiproton studies
Energy Technology Data Exchange (ETDEWEB)
We describe the PBAR balloon-borne magnet spectrometer flown on August 13-14, 1987 to measure the abundance of cosmic ray antiprotons in the energy interval 100-1580 MeV at the top of the atmosphere. The limits first reported have been improved to an overall limit of anti p/p<2.0x10{sup -5} (85% CL). We summarize the overall design and performance of the PBAR spectrometer, which had the unique ability to establish the mass of each singly charged cosmic ray, as well as to reject spurious antimatter candidates caused by hard scatterings within the instrument. (orig.).
1990-09-15
One-dimensional free boundary problem for actin-based propulsion of Listeria
Some bacteria move inside cells by recruiting the actin filaments of the host cells. The filaments are polymerized at the back surface of the bacteria, and they move away, forming a "comet" tail behind the bacterium, which consists of gel network. We develop a one-dimensional mathematical model of the gel based on partial differential equations which involve the number of filaments, the density and velocity of the gel, and the pressure. The two end-points of the gel form two free boundaries. The resulting free boundary problem is rather non-standard. We prove local existence and uniqueness.
2007-04-01
... We strive to meet the needs of our members at as low a cost as possible. Visit website eSight Energy eSight Energy ...eSight® is the most advanced fully web enabled energy monitoring and targeting package on the market. This comprehensive and intuitive energy management suite ...Drinks Company We have developed the worlds most environmentally friendly cold drinks vending system. Over 40 different drinks available which are good for ...EcoSort® recycling system has been designed to offer customers a unique and flexible solution for the source separation of waste materials. Visit website ...
Mechanisms of high-T/sub c/ superconductivity in low-dimensional materials
Energy Technology Data Exchange (ETDEWEB)
High-T/sub c/ superconductivity is due to the action of two mechanisms: (1) plasmon mechanism, i.e., exchange of two-dimensional (2-D) plasmons and (2) strong electron--phonon coupling. The low dimensionality and the small value of the carrier concentration make the plasmon mechanism favorable. The small value of the coherence length leads to a unique opportunity to observe a multigap structure. The proximity effect can be used in order to increase T/sub c/ of A-15 compounds.
1987-11-01
Marketing opportunity for industries/power plants -- the Swedish case
Energy Technology Data Exchange (ETDEWEB)
This paper describes and analyses the new situation in the electricity market in Sweden and the attendant emergence of a unique marketing opportunity for industries and power plants to capitalize on bioenergy. This recent marketing opportunity, which is based on consumer demand, has come about through a number of recent institutional changes in Sweden that have drastically lowered the transaction costs associated with the purchase of green electricity, i.e. electricity generated in what is classified as an environmentally sound manner. This has created a functioning market for green electricity and products made using green electricity.
1996-12-31
Locked nucleic acid (LNA): High affinity targeting of RNA for diagnostics and therapeutics
DEFF Research Database (Denmark)
Locked nucleic acid (LNA) is a nucleic acid analogue containing one or more LNA nucleotide monomers with a bicyclic furanose unit locked in an RNA mimicking sugar conformation. This conformational restriction results in unprecedented hybridization affinity towards complementary single stranded RNA and thus, makes LNA uniquely suited for mimicking RNA structures and sequence specific targeting of RNA in vitro or in vivo. The focus of this paper is on LNAantisense, LNA-modified siRNA (siLNA), and detection and analysis of microRNAs by LNA-modified oligonucleotide probes.
2005-01-01
Leak detection on petroleum pipelines
Energy Technology Data Exchange (ETDEWEB)
This paper presents a unique method, currently under evaluation, that can continuously track pipeline operation providing essentially instantaneous responses to leaks or ruptures without causing a pressure drop or energy loss. Using the highly linear characteristics of a very accurate and repeatable meter and then correlating it to a second identical unit, a dynamic leak detection system is planned that can be retrofitted on existing pipelines without a major construction effort nor destroying the integrity of the existing transmission line. Initial tests performed on a crude oil transmission line verified the equipment's performance and established that the repeatability limits are sufficient to continue development of the concept.
1984-04-01
Since the mid-1980s the number of scientists from all over the world using CERN's facilities has increased enormously. Currently more than 6,000 users, over half of the planet's high-energy physicists, carry out fundamental research at CERN. This user community is living proof that CERN welcomes inter- regional collaboration which benefits all and boosts the progress of science. The LHC, the only machine capable of addressing problems way beyond today's frontiers of high energy physics, offers an unique opportunity for extending world wide collaboration.
1994-01-01
Laser Based In Situ Techniques: Novel Methods for Generating Extreme Conditions in TEM Samples
Energy Technology Data Exchange (ETDEWEB)
The Dynamic Transmission Electron Microscope (DTEM) is introduced as a novel tool for in situ processing of materials. Examples of various types of dynamic studies outline the advantages and differences of laser-based heating in the DTEM in comparison to conventional (resistive) heating in situ TEM methods. We demonstrate various unique capabilities of the drive laser, namely, in situ processing of nanoscale materials, rapid and high temperature phase transformations, and controlled thermal activation of materials. These experiments would otherwise be impossible without the use of the DTEM drive laser. Thus, the potential of the DTEM to as a new technique to process and characterize the growth of a myriad of micro and nanostructures is demonstrated.
2008-02-25
Incremental learning for recognizing handwritten characters using neural networks
Energy Technology Data Exchange (ETDEWEB)
Artificial Neural Networks (ANNs) are parallel distributed processing machines. The unique characteristics of ANNs are: Fault tolerance, robustness, plasticity and generalization. These offer great potential in many AI applications such as character recognition. Handwritten character recognition is an intrinsically interesting problem, but the difficulties of this task are the many variations in the characters. A robust new incremental learning method, which combines supervised and unsupervised learning paradigms implemented by the Functional Link Net, is illustrated with experimental results. Clustering, based on unsupervised learning, classifies the input data into several categories. The supervised learning paradigm then further classifies the data in the clustered categories.
1989-01-01
In-situ TEM study of dislocation-twin boundaries interaction in nanotwinned Cu films
British Library Electronic Table of Contents (United Kingdom)
Epitaxial thin films of nanotwinned face-centered cubic metals such as Cu possess an unprecedented combination of high hardness and high electrical conductivity due to the unique structure of nanometer-spaced coherent twin boundaries. Recent studies of in-situ nanoindentation in a transmission electron microscope have provided new insights on the deformation behavior of nanotwins that are reviewed here. In particular, two unit processes are highlighted: first, stress-induced migration of ?3 {112} incoherent twin boundary that leads to de-twinning of nanotwins; second, twinning dislocation can be multiplied at ?3 {111} coherent twin boundary.
2011-01-01
In situ observation of axial irradiation growth in liquid-metal reactor metal fuel
International Nuclear Information System (INIS)
Effects of the rapid early-in-life expansion of metal fuel were measured in an irradiation experiment in the Fast Flux Test Facility (FFTF). This important performance/design information was obtainable through the unique combination of a dimensionally stable FFTF oxide core and the calibrated proximity instrumentation associated with the test. These results delineate the time dependence of metal-fuel swelling and provide quantitative estimates of the magnitude of axial fuel swelling in full-length metal-fuel assemblies. Final posttest examination results will define actual fuel column growth levels.
1989-11-26
IDEAS: Journal of Public Economic Theory, Association for Public Economic Theory
... Bednarek & Rowena A. Pecchenino & Sally C. Stearns [Downloadable! (restricted)] 317-327 On the Existence and Uniqueness of Pure-Strategy Nash Equilibrium in Asymmetric Rent-Seeking Contests by Takeshi Yamazaki [Downloadable! (restricted)] 2008, Volume 10, Issue 1 1-5 The Journal of Public Economic Theory at Ten Years Old by John P. Conley & Myrna Wooders [Downloadable! (restricted)] 7-26 Strategy-Proofness and the Tops-Only Property by John A. Weymark [Downloadable! (restricted)]...
Hybridisation and crystal field in YbPd sub 2 Si sub 2
Energy Technology Data Exchange (ETDEWEB)
Experimental data in the hybridised compound YbPd{sub 2}Si{sub 2} is compared with the results obtained with a recently proposed hybridisation model, based on the ''large-degeneracy expansion'' approximation, which takes into account the crystal field splittings of the rare earth ion energy levels. With a unique set of parameters, satisfactory agreement is simultaneously obtained for the thermal variation of the electronic specific heat, of the magnetic susceptibility and of the electric field gradient at the Yb site, as well as for the field variation of the low temperature magnetisation. (orig.).
1991-02-01
High energy beams of radioactive nuclei and their biomedical applications
Energy Technology Data Exchange (ETDEWEB)
It is possible to produce energetic beams of radioactive nuclei, as secondary beams, from the heavy-particle compound accelerator called BEVALAC. These beams can be focused into experimental areas without significant contamination using suitable magnetic filters and proper beam-optics. Properly selected high-energy beams of radioactive nuclei (those which defay by positron emission) can provide a truly unique opportunity to evaluate the effectiveness of these beams in localizing the Bragg peak on a tumor volume - necessary in heavy-particle therapy. Preliminary data are presented here to demonstrate the possible use of these beams in radiotherapy treatment-planning verification.
1981-04-01
High Exposure Facility Technical Description
Energy Technology Data Exchange (ETDEWEB)
The High Exposure Facility is a collimated high-level gamma irradiator that is located in the basement of the 318 building. It was custom developed by PNNL back in 1982 to meet the needs for high range radiological instrument calibrations and dosimeter irradiations. At the time no commercially available product existed that could create exposure rates up to 20,000 R/h. This document is intended to pass on the design criteria that was employed to create this unique facility, while maintaining compliance with ANSI N543-1974, "General Safety Standard for Installations Using Non-Medical X-Ray and Sealed Gamma-Ray Sources, Energies up to 10 MeV."
2008-02-12
HANARO cooling features: design and experience
International Nuclear Information System (INIS)
In order to achieve the safe core cooling during normal operation and upset conditions, HANARO adopted an upward forced convection cooling system with dual containment arrangements instead of the forced downward flow system popularly used in the majority of forced convection cooling research reactors. This kind of upward flow system was selected by comparing the relative merits of upward and downward flow systems from various points of view such as safety, performance, maintenance. However, several operational matters which were not regarded as serious at design come out during operation. In this paper are presented the design and operational experiences on the unique cooling features of HANARO. (author)
1999-08-01
Giving voice to the past: digitizing oral history
British Library Electronic Table of Contents (United Kingdom)
Purpose - The purpose of this paper is to describe the processes and procedures utilized by Jacksonville State University's Houston Cole Library to digitize an oral history collection and provide access to it through the Library's catalog, web presence, and the state-wide digital repository initiative, Alabama Mosaic (see www.alabamamosaic.org). Design/methodology/approach - The paper is based on the Library's experiences in acquiring, digitizing, creating metadata for and making accessible a collection of oral histories. Findings - The paper describes the obstacles overcome, issues encountered, procedures established, and ramifications of the project. Practical implications - Many institutions are currently digitizing unique collections as part of repository initiatives, both institutiona...
2009-01-01
International Nuclear Information System (INIS)
The Federal Republic of German (FRG) had uniquely strict emission legislation for particulates SO_2 and NO_X from fossil-fired power plants. The 13th Regulation to the Federal Emission Control Act required that by 1 July 1988 all large furnaces fired with solid or liquid fuels that would not be decommissioned by 1993 be retrofitted with SO_2 control technology. The emission limits are 15 per cent of the sulphur introduced with the fuel (400 mg/m"3 maximum) at thermal capacities above 300 MW. 1 ref., 9 figs, 15 bibliographies.
1991-12-01
Fitting the fully coupled ORM for the Fermilab Booster
Energy Technology Data Exchange (ETDEWEB)
The orbit response matrix (ORM) method [1] is applied to model the Fermilab Booster with parameters such as the BPM gains and rolls, and parameters in the lattice model, including the gradient errors and magnets rolls. We found that the gradients and rolls of the adjacent combined-function magnets were deeply correlated, preventing full determination of the model parameters. Suitable constraints of the parameters were introduced to guarantee an unique, equivalent solution. Simulations show that such solution preserves proper combinations of the adjacent parameters. The result shows that the gradient errors of combined-function magnets are within design limits.
2005-05-01
FORTE antenna element and release mechanism design
Energy Technology Data Exchange (ETDEWEB)
The Fast On-Orbit Recording of Transient Events (FORTE) satellite being built by Los Alamos National Laboratory (LANL) and Sandia National Laboratories (SNL) has as its most prominent feature a large deployable (11 m by 5 m) log periodic antenna to monitor emissions from electrical storms on the Earth. This paper describes the antenna and the design for the long elements and explains the dynamics of their deployment and the damping system employed. It also describes the unique paraffin-actuated reusable tie-down and release mechanism employed in the system.
1995-02-01
Explosives synthesis at Los Alamos
Energy Technology Data Exchange (ETDEWEB)
During the past two decades, the explosives synthetic effort at Los Alamos has been directed toward energetic heterocylic compounds and has produced some useful thermally stable explosives. The recent evolution of crystal-density predictive methods is guiding our current efforts toward ultrahigh performance explosives. Much of our effort is now on the development of new methods for preparing unique nitro compounds that are inaccessible by conventional techniques. This paper reviews the Los Alamos synthetic program with emphasis on the development of novel thermally stable explosives, and current efforts to synthesize high-density/performance explosives will be discussed.
1986-03-01
Experiences with distributing graphic software between processors
Energy Technology Data Exchange (ETDEWEB)
Software to aid the distribution and coordination of tasks between different processors was developed to distribute applications written in Fortran. This development led to the discovery of problems unique to Fortran and to interesting practical solutions. Two graphical applications were distributed to a variety of machines and machine pairs: CDC 7600-LSI/11, CRAY-LSI/11, VAX 11/780, and Apollo. These distributions pointed out several parameters such as the use of Fortran COMMON, communication parameters, and processing capabilities that can affect the successful distribution of applications.
1982-01-01
Epidemiological studies of radiation carcinogenesis and its biophysical basis
International Nuclear Information System (INIS)
The three projects of the research program are aimed at the epidemiological study of long-term radiation effects in patients injected with radium-224. They are: late effects in "2"2"4Ra treated ankylosing spondylitis patients, late effects in "2"2"4Ra treated juvenile and adult patients, and epidemiology of radiation carcinogenesis. The data from these patients are a unique source of information for risk analysis of incorporated bone seeking radionuclides in man. (R.P.) 5 refs., 3 tabs.
Engineering Optimisation by Cuckoo Search
A new metaheuristic optimisation algorithm, called Cuckoo Search (CS), was developed recently by Yang and Deb (2009). This paper presents a more extensive comparison study using some standard test functions and newly designed stochastic test functions. We then apply the CS algorithm to solve engineering design optimisation problems, including the design of springs and welded beam structures. The optimal solutions obtained by CS are far better than the best solutions obtained by an efficient particle swarm optimiser. We will discuss the unique search features used in CS and the implications for further research.
2010-01-01
International Nuclear Information System (INIS)
Mass spectrometry was instrumental in the discovery of the fullerenes and the characterization of their special structure (truncated icosahedron). High resolution and high sensitivity mass spectrometry in combination with a crossed molecular beam/electron beam ion source is used here to study a further, very unique property of singly and multiply charged fullerene ions (up to Z=7), i.e. their strong resilience towards decomposition via sequential C_2 evaporation and via Coulomb explosion, respectively. (author).
1994-03-20
Electromagnetic wiggler technology development at the Lawrence Livermore National Laboratory
Energy Technology Data Exchange (ETDEWEB)
As a part of the program at the Lawrence Livermore National Laboratory (LLNL) in induction-linac free-electron laser (IFEL) research, the authors are conducting a variety of activities addressing the unique requirements imposed on IFEL wiggler systems. They are actively developing improved DC iron-core electromagnetic wiggler designs to attain higher peak fields, greater tunability, and lower random error levels. They are pursuing specialized control systems, such as magnetic-field and beam-position controllers, which can relax requirements on the wiggler itself. They are also pursuing basic studies to establish the effect of radiation on permanent magnets.
1988-03-01
Electromagnetic wiggler technology development at the Lawrence Livermore National Laboratory
Energy Technology Data Exchange (ETDEWEB)
As a part of the program at the Lawrence Livermore National Laboratory (LLNL) in induction-linac free-electron laser (IFEL) research, we are conducting a variety of activities addressing the unique requirements imposed on IFEL wiggler systems. We are actively developing improved dc iron-core electromagnetic wiggler designs to attain higher peak fields, greater tunability, and lower random error levels. We are pursuing specialized control systems, such as magnetic-field and beam-position controllers, which can relax requirements on the wiggler itself. We are also pursuing basic studies to establish the effect of radiation on permanent magnets.
1987-01-01
Dimensionally dependent luminescence of boron difluoride ?-diketonates
International Nuclear Information System (INIS)
The results of the study of dimensionally dependent fluorescence of boron difluoride ?-diketonates of general formula (R1COCHCOR2)BF2 are presented. The fact that for most of the compounds studied a noticeable hypsochrome shift of the luminescence band maximum is characteristic during transition from bulk crystals to microcrystals was detected. However, for boron difluoride dibenzoylmethanate having a unique supramolecular structure, a bathochromic shift of luminescence due to the crustal size reduction is observed. The dimensionally dependent luminescence properties of the complexes have been analyzed within the exciton mechanism
2008-06-01
Energy Technology Data Exchange (ETDEWEB)
Renewable energy systems (RES) are unique among energy supply systems because their performance and design depends entirely on the location and climatic conditions. As a result of design options, user requirements and local climatic conditions, there are enormous variations between RES. This paper describes a method how to evaluate the data on monitored renewable energy systems (RES) in such a way that the operating conditions and performance of individual components and the system as a whole can be analysed and compared. It shows how categories of similar use can be defined and recommendations for each category can be made to assist in the selection of the most suitable products. (orig.)
2004-07-01
Development of Synthol circulating fluidized bed reactors
Energy Technology Data Exchange (ETDEWEB)
In 1980 Sasol completed its very large coal conversion complex, Sasol Two and Three in South Africa. This complex, the largest coal-to-liquids facility in the world, utilizes Sasol's proprietary Fischer-Tropsch technology, the Synthol Process. The two key elements of the Synthol Process are its catalyst and its unique fluidized bed reactor, the Synthol Circulating Fluidized Bed Reactor. Details on the catalytic aspects and reaction mechanism have been given elsewhere. In this paper, the history of the development of the reactor is discussed.
1986-08-01
International Nuclear Information System (INIS)
This paper is concerned with the determination of a unique scaling parameter in complex scaling analysis and with accurate calculation of dynamics resonances. In the preceding paper we have presented a theoretical analysis and provided a formalism for dynamical resonance calculations. In this paper we present accurate numerical results for two non-trivial dynamical processes, namely, models of diatomic molecular predissociation and of barrier potential scattering for resonances. The results presented in this paper confirm our theoretical analysis, remove a theoretical ambiguity on determination of the complex scaling parameter, and provide an improved understanding for dynamical resonance calculations in rigged Hilbert space.
2008-03-15
Description of odd-A nuclei in the Pt region in the interacting boson-fermion model
Energy Technology Data Exchange (ETDEWEB)
Properties of unique parity states in odd-proton (/sub 77/Ir, /sub 79/Au) and odd-neutron nuclei (/sub 78/Pt) are investigated in the framework of the interacting boson-fermion approximation model. The core (boson)-particle (fermion) interaction is represented by a quadrupole-quadrupole interaction and an exchange term, which takes into account the effects of the Pauli exclusion principle. The even-even core nucleus is described in terms of the IBA-1 hamiltonian. The change in the properties of the corresponding odd-A nuclei can be interpreted in terms of a transition of the core hamiltonian between the O(6) and SU(3) limiting cases.
1982-05-03
Description of odd-A nuclei in the Pt region in the interacting boson-fermion model
International Nuclear Information System (INIS)
Properties of unique parity states in odd-proton (_7_7Ir, _7_9Au) and odd-neutron nuclei (_7_8Pt) are investigated in the framework of the interacting boson-fermion approximation model. The core (boson)-particle (fermion) interaction is represented by a quadrupole-quadrupole interaction and an exchange term, which takes into account the effects of the Pauli exclusion principle. The even-even core nucleus is described in terms of the IBA-1 hamiltonian. The change in the properties of the corresponding odd-A nuclei can be interpreted in terms of a transition of the core hamiltonian between the O(6) and SU(3) limiting cases. (orig.).
Long cylindrical mirror sections with an 'Alliptical' cross- section and an interfoci distance of approximately 1 m can be produced by means of diamond fly cutting. However, because of the finite tool radius, the generated profile is basically not an ellipse, but an equidistant ellipse or 'Allipse'. By numerical ray tracing analysis two unique conjugated 'A-points' can be found that are optically nearly equivalent with pure elliptical focal points. A reversed modeling procedure is used to predict the optimum machine configuration for producing just the required ellipse sections. Optical figure quality, focal line position and straightness are tested by a simple deflectometer set-up.
1999-09-01
Cosmic no-hair theorem in power-law inflation
Energy Technology Data Exchange (ETDEWEB)
We prove a cosmic no-hair theorem for Bianchi models in power-law inflation. Provided that the potential of an inflaton {phi} is exp({minus}{lambda}{kappa}{phi}) with 0{le}{lambda}{lt} {radical}2/3 , we find that the isotropic power-law solution is the unique attractor for any initially expanding Bianchi-type models except type IX. For Bianchi type IX, this conclusion is also true if the initial ratio of the vacuum energy to the maximum three-curvature is larger than one half.
1992-02-15
Climate change - the contribution from air travel
International Nuclear Information System (INIS)
The paper discusses the Intergovernment Panel on Climate Change (IPCC) report on Aviation and the Global Atmosphere (published in 1999). It was considered necessary to treat air transport on its own since aircraft are unique in delivering emissions into the upper atmosphere rather than at ground level. The study was commissioned at the request of the International Civil Aviation Organisation and the Montreal Protocol. More than 300 experts contributed and the report has quantified the effect of aviation on the atmosphere on a world wide basis and highlighted areas where improved data are required. (UK)
2000-04-01
Carbon fiber/epoxy matrix composite springs as self-centering supports: manufacture and evaluation
Energy Technology Data Exchange (ETDEWEB)
A variety of engineering and experimental applications require primary support structures which are self-centering. High mechanical strength, low-density, carbon fiber/epoxy matrix composite springs are used in unique planar, cylindrical, conical, and spherical configurations to self-center components. The sinusoidal and triangular-shaped composite springs are readily manufactured and assembled into component hardware. Design considerations, flexural strength properties, load bearing and centering data plus procedures for the manufacture of composite springs are presented.
1984-01-01
Calculation of ice accumulation rates in Antarctica over the last glacial cycle.
Environmental Research Database
DescriptionRates of ice accumulation in Antarctica are not known well, yet they are fundamental to assessing the ice sheet mass balance. Past accumulation rates are less well defined. We are in a unique position to provide detailed accounts of accumulation in Antarctica. We will measure isochronous internal layering across the ice sheet, which can be readily identified in radar data that we hold. Internal layers will be traced to ice-cores (allowing dating) and across wide regions of the ice sheets. A nume [continued...
2006-01-08
Breached fuel location in FFTF by delayed neutron monitor triangulation
International Nuclear Information System (INIS)
The purpose of this work was to develop and evaluate a method of locating breached fuel within the Fast Flux Test Facility (FFTF) reactor based on the relative response of the delayed neutron monitors (DNM) located on each of the three primary sodium cooling loops. The primary method of location is the use of tag gas containing unique ratios of the noble gases xenon and krypton. Although the tag gas system works quite well, it is relatively expensive because of the costs of preparing and loading the gas into each fuel pin. Triangulation of DNM signals could potentially decrease tag gas costs while maintaining overall location reliability.
1985-11-10
Automatic Control via Thermostats of a Hyperbolic Stefan Problem with Memory
A hyperbolic Stefan problem based on the linearized Gurtin-Pipkin heat conduction law is considered. The temperature and free boundary are controlled by a thermostat acting on the boundary. This feedback control is based on temperature measurements performed by real thermal sensors located within the domain containing the two-phase system and/or at its boundary. Three different types of thermostats are analyzed: simple switch, relay switch, and a Preisach hysteresis operator. The resulting models lead to integrodifferential hyperbolic Stefan problems with nonlinear and nonlocal boundary conditions. Existence results are proved in all the cases. Uniqueness is also shown, except in the situation corresponding to the ideal switch.
1999-03-15
Animal experiments on the biokinetics of astatide and astate-(I)-complex compounds
International Nuclear Information System (INIS)
The radiation properties of the #alpha# emitter "2"1"1At are in favor of its application malignant tumor therapy. As a basis for further investigations the biokinetics of At"-, At x H_2O, At I_2"-, and [At(thio)_2]"+ were determined after i.v. injection into healthy and tumor-bearing mice. The estimation of the ion mobility of the carrier-free compounds allowed the use of uniquely characterized initial compounds. The organ distribution of all species examined was similar to the distribution of astatide. Accumulation was found in the thyroid and other inner organs. (author).
Energy Technology Data Exchange (ETDEWEB)
The Nuclear Regulatory Commission (NRC) on December 29, 1993, promulgated self-guarantee requirements that materials licensees may use to demonstrate financial assurance for decommissioning costs. However, nonprofit colleges and universities, nonprofit hospitals, and for-profit firms that do not issue bonds are currently precluded, by their unique accounting and financial reporting systems, or by other features of their business practices, from using the financial tests for self-guarantors adopted by the NRC. This Report evaluates several alternative financial tests that might serve as the basis for self-guarantee by these three categories of licensees.
1997-06-01
Energy Technology Data Exchange (ETDEWEB)
We present a case of cerebral aspergillosis in an immunocompetent patient. The MRI signal characteristics were compared with the histologic findings. Irregular low-signal zones were demonstrated between the wall of the abscess and the central necrosis on T2-weighted images; the pathology specimen revealed concentrated iron in these transitional zones but no hemosiderin. Iron is an essential element for the growth of fungal hyphae. The low-signal zones may represent the areas where there was active proliferation of aspergillus, and the unique location of the low signal may be a helpful imaging characteristic for the diagnosis of an aspergillus abscess. (orig.)
2001-07-01
Task 5.9 - use of coal ash in recycled plastics and composite materials
Energy Technology Data Exchange (ETDEWEB)
The goal of this research project by the Energy & Environmental Research Center (EERC) was to determine the potential for coal ash to serve as a {open_quote}functional filler{close_quotes} in plastics and other composite materials, with special emphasis on recycled plastics. The term functional filler is intended to indicate that the material added to the plastic does more than take up space and extend the use of the polymer. Determining the functional filler potential of ash was not the only intent of this project, since another prime objective was to find a use for materials currently considered waste. The term functional filler also opened a door to the use of cenospheres, which are currently marketed and for which there is sufficient market demand that they do not fit the category of a waste even though they are a product of coal combustion. Cenospheres, hollow spherical ash particles, were selected because of their unique properties. Although they ...
1995-07-01
Energy Technology Data Exchange (ETDEWEB)
Purpose: The aim of this study was to test the feasibility of iliac artery stent placement under MR guidance with real-time MR radial scanning in an animal model. Materials and methods: The experiments were performed on three pigs in a 1.5 T scanner. Radial scanning with a gradient echo technique (T{sub R} 8.4 ms, T{sub E} 3.6 ms, flip angle 10 ) was used. A dedicated backprojector performed the reconstruction of the raw data in real-time. The resulting MR-images were displayed on LCD screens beside the magnet. The sliding window reconstruction technique allowed image acquistion at a frame rate of 16 images per second. MR-compatible self-expanding stents with a diameter of 8 mm and a length of 3 cm were placed into the left iliac artery. Their positions were verified by digital subtraction angiography (DSA) and compared to MRI. Results: All stents were successfully placed. Stent positions as monitored by real-time MR were identical to those seen on DSA images. The ...
1998-12-01
Energy Technology Data Exchange (ETDEWEB)
A cooperative effort of the Center for Solar Energy and Hydrogen Research (ZSW) and Phototronics Solartechnik GmbH (PST) aimed at the transfer of highly efficient solar cells developed on a laboratory scale, to large-area thin-film solar modules suitable for production. This work was based on research and development at the Institute for Physical Electronics (IPE) of Stuttgart University and ZSW on one hand, and on the know-how of PST in regard to large-area module fabrication on the other hand. The various thin-film layers of the cells and modules comprize molybdenum as rear contact, copper-indium(gallium)-diselenide (CIGS) as absorber material, the combination of cadmium sulphide (CdS) and ZnO as window layer. To produce these layers on large areas (30x30 cm{sup 2}), equipment was constructed and procedures were developed. Monolithic series connection of cells, used in other thin-film technologies, was studied and optimized by suitable patterning procedures, such ...
1998-06-01
[Conversion of acetic acid to methane by thermophiles
The primary goal of this project is to obtain a better understanding of thermophilic microorganisms which convert acetic acid to CH[sub 4]. The previous funding period represents a departure from earlier research in this laboratory, which was more physiological and ecological. The present work is centered on the biochemistry of the thermophile Methanothrix sp. strain CALS-1. this organism presents a unique opportunity, with its purity and relatively rapid growth, to do comparative biochemical studies with the other major acetotrophic genus Methanosarcina. We previously found that Methanothrix is capable of using acetate at concentrations 100 fold lower than Methanosarcina. This finding suggests that there are significant differences in the pathways of methanogenesis from acetate in the two genera.
1993-01-01
Wettability and osteoblast cell response modulation through UV laser processing of nylon 6,6
British Library Electronic Table of Contents (United Kingdom)
With an ageing population the demand for cheap, efficient implants is ever increasing. Laser surface treatment offers a unique means of varying biomimetic properties to determine generic parameters to predict cell responses. This paper details how a KrF excimer laser can be employed for both laser-induced patterning and whole area irradiative processing to modulate the wettability characteristics and osteoblast cell response following 24h and 4 day incubation. Through white light interferometry (WLI) it was found that the surface roughness had considerably increased by up to 1.5mm for the laser-induced patterned samples and remained somewhat constant at around 0.1mm for the whole area irradiative processed samples. A sessile drop device determined that the wettability characteristics diffe...
2011-01-01
Wealth accumulation among U.S. immigrants: A study of assimilation and differentials
British Library Electronic Table of Contents (United Kingdom)
Data from the New Immigrant Survey are used to study wealth differentials among U.S. legal permanent residents. This study is unique in its ability to account for wealth held in the U.S. and that held abroad and yields several key findings. First, relative to immigrants from Western Europe, Australia, Canada, and New Zealand (who have median wealth similar to native born non-Hispanic whites), other immigrant groups have lower levels of total wealth even after accounting for permanent income and life course characteristics. Second, time in the U.S. is positively associated with the wealth of married immigrants, yet this relationship is not statistically significant for single immigrants. Third, differences in the means of measured characteristics between Western European immigrants and thos...
2011-01-01
VLF wave stimulation by pulsed electron beams injected from the space shuttle
International Nuclear Information System (INIS)
Among the investigations conducted on the space shuttle flight STS 3 March 1982 was an experiment in which a 1-keV, 100-mA electron gun was pulsed at 3.25 and 4.87 kHz. The resultant waves were measured with a broadband plasma wave receiver. At the time of flight the experimental setup was unique in that the electron beam was square wave modulated and that the shuttle offered relatively long times for in situ measurements of the ionospheric plasma response to the VLF pulsing sequences. In addition to electromagnetic response at the pulsing frequencies the waves exhibited various spectral harmonics as well as the unexpected occurrence of satellite lines around those harmonics. Both phenomena occurred with a variety of different characteristics for different pulsing sequences.
U.S. military workingn> dogs with Vietnam service: definition and characteristics of the cohort.
We verified and corrected inaccuracies in descriptive profile information on military working dogs (MWDs) that died from 1965 to 1980 and were reported in the Armed Forces Institute of Pathology Registry of Veterinary Pathology. Using other available military records, we determined which dogs served in Vietnam. Identified were 3,895 MWDs with a unique identity tattoo that served in Vietnam, of which 2,389 served exclusively with U.S. military forces and died in Vietnam. Another 479 Vietnam veteran MWDs completed their service elsewhere. This overall effort resulted in signalment corrections, generally age at death, in 21% of the Registry MWD accessions during the study period. The improved definition and characterization of the Vietnam cohort will lead to greater precision in epidemiologic investigations of the health effects from the Vietnam experience in U.S. military working dogs. PMID:7885593
1994-11-01
Transuranic radionuclides dispersed into the environment at accident sites, a bibliography
Energy Technology Data Exchange (ETDEWEB)
The purpose of this project was to compile a bibliography of references containing environmental transuranic radionuclide data. The authors intent was to identify those parameters affecting transuranic radionuclide transport that may be generic and those that may be dependent on chemical form and/or environmental conditions. An understanding of the unique characteristics and similarities between source terms and environmental conditions relative to transuranic radionuclide transport and cycling will provide the ability to assess and predict the long term impact on man and the environment. An additional goal of the literature review, was to extract the ranges of environmental transuranic radionuclide data from the identified references for inclusion in a data base. Related to source term, these ranges of data can be used to calculate the dose to man from the radionuclides, and to perform uncertainty analyses on these dose assessments.
1994-07-01
The structure of an active acoustic metamaterial with tunable effective density
Energy Technology Data Exchange (ETDEWEB)
A new class of one-dimensional active acoustic metamaterials (AAMMs) with programmable effective densities is presented. The proposed AAMM is capable of producing densities that are orders of magnitudes lower or higher than the ambient fluid. Such characteristics are achieved by using an array of fluid cavities separated by piezoelectric diaphragms that are controlled to generate constant densities over wide frequency bands. The piezodiaphragms are augmented with passive electrical components to broaden the operating frequency bandwidth and enable densities higher than the fluid medium to be generated. The use of these components is shown to be essential to maintain the closed-loop compliance of the piezodiaphragm away from the zone of elastic instabilities. The values of the passive components are selected on a rational basis in order to ensure a balance between the frequency bandwidth and control voltage. With this unique structure of the AAMM, physically ...
2009-12-15
The search for decaying Dark Matter
We propose an X-ray mission called Xenia to search for decaying superweakly interacting Dark Matter particles (super-WIMP) with a mass in the keV range. The mission and its observation plan are capable of providing a major break through in our understanding of the nature of Dark Matter (DM). It will confirm, or reject, predictions of a number of particle physics models by increasing the sensitivity of the search for decaying DM by about two orders of magnitude through a wide-field imaging X-ray spectrometer in combination with a dedicated observation program. The proposed mission will provide unique limits on the mixing angle and mass of neutral leptons, right handed partners of neutrinos, which are important Dark Matter candidates. The existence of these particles is strongly motivated by observed neutrino flavor oscillations and the problem of baryon asymmetry of the Universe. In super-WIMP models, the details of the formation of the cosmic web are different from ...
2009-01-01
The objectives for deep scientific drilling in Yellowstone National Park
Energy Technology Data Exchange (ETDEWEB)
The western area of the United Stated contains three young silicic calderas, all of which contain attractive targets for scientific drilling. Of the three, the Yellowstone caldera complex is the largest, has the most intense geothermal anomalies, and is the most seismically active. On the basis of scientific objectives alone. it is easily the first choice for investigating active hydrothermal processes. This report briefly reviews what is known about the geology of Yellowstone National Park and highlights unique information that could be acquired by research drilling only in Yellowstone. However, it is not the purpose of this report to recommend specific drill sites or to put forth a specific drilling proposal. 175 refs., 9 figs., 2 tabs.
1987-01-01
The numerical response of breeding Northern Saw-whet Owls Aegolius acadicus suggests nomadism
British Library Electronic Table of Contents (United Kingdom)
We used a 13-year time series of abundance estimates of breeding Northern Saw-whet Owls (Aegolius acadicus), and of small mammals from central Ontario, Canada, to assess the numerical response of the owls to small-mammal prey species. We found that the finite rate of increase of breeding owls was directly related to estimates of red-backed vole (Myodes gapperi) abundance. Thus, it appeared that the owls were nomadic, and made decisions about where to breed based on vole supply. The owls showed a much weaker response to deer mouse (Peromyscus maniculatus) abundance. Across all years, 55% of variation in owl rate of increase could be uniquely attributed to vole abundance, whereas only 3% could be attributed to mouse abundance. Consistent with the model of nomadism, there was only a weak rela...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
Mammalodon colliveri is an unusual toothed archaic mysticete (Cetacea) from the Upper Oligocene Jan Juc Formation of south-east Australia. The morphology of the holotype skull and postcrania are described in detail. Superimposed on the generally plesiomorphic archaeocete-like morphology of Mammalodon are subtle mysticete synapomorphies. Derived features of Mammalodon include a short and bluntly rounded rostrum, reduced premaxillae, and anterodorsally directed orbits. Within Mysticeti, this suite of features is unique. The aberrant rostral morphology of Mammalodon suggests specialization for suction feeding. Janjucetus hunderi is placed in an expanded family Mammalodontidae. Phylogenetic analysis corroborates the monophyly of Basilosauridae, Neoceti, Odontoceti, and Mysticeti, and yields a ...
2010-01-01
The geometry emerging from the symmetries of a quantum system
We investigate the relation between the symmetries of a quantum system and its topological quantum numbers, in a general C*-algebraic framework. We prove that, under suitable assumptions on the symmetry algebra, there exists a generalization of the Bloch-Floquet transform which induces a direct-integral decomposition of the algebra of observables. Such generalized transform selects uniquely the set of "continuous sections" in the direct integral, thus yielding a Hilbert bundle. The emerging geometric structure provides some topological invariants of the quantum system. Two running examples provide an Ariadne's thread through the paper. For the sake of completeness, we review two related theorems by von Neumann and Maurin and compare them with our result.
2009-01-01
The duke XUV FEL storage ring facility
Energy Technology Data Exchange (ETDEWEB)
In this paper we present status and developments of the Duke storage ring facility. The Duke storage ring facility provides the unique combination of phase-locked light sources ranging from high power OK-4 XUV FEL to quasimonochromatic {gamma}-ray beam and IR/X-ray spontaneous radiation. The XUV OK-4 FEL, which is collaborative project with BlNP, Novosibirsk, is in operation since November, 1996. The OK-4 UV FEL is also used for production of nearly monochromatic {gamma}-ray s with tunable energy. We present the results of UV lasing with the OK4 FEL and selected results of its applications. We will discuss our future plans for extension of this source and status of the construction of dedicated used facility adjacent to the FEL building. (author)
1998-11-01
The Darrieus-type Vertical Axis Wind Turbine (VAWT) presents a variety of unusual structural problems to designers. The level of understanding of these structural problems governs, to a large degree, the success or failure of today's rotor designs. A survey is presented of the technology available for rotor structural design with emphasis on the DOE research program now underway. Itemizations are included of the major structural issues unique to the VAWT along with discussion of available analysis techniques for each problem area. It is concluded that tools are available to at least approximately address the most important problems. However, experimental data for confirmation is rather limited in terms of volume and the range of rotor configurations tested.
1982-01-01
Temperature Dependent Constitutive Modeling for Magnesium Alloy Sheet
International Nuclear Information System (INIS)
Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are compared.
2010-06-15
Targeted integration of baboon endogenous virus in the BEVI locus on human chromosome 6.
The infection of cultured human cells with baboon endogenous virus (BEV) frequently leads to an association of viral DNA with a specific genetic locus (termed BEVI, for baboon endogenous virus infection) on chromosome 6. Restriction endonuclease digestion of DNA from BEV-infected human cells and their derived somatic cell clones frequently revealed a common cellular DNA sequence in the proximity of one of the junctions between cellular DNA and the integrated virus. We propose that a short cellular DNA sequence, repeated on chromosome 6 and separated by unique DNA sequences, presents a high-affinity target for the integration of BEV in human cells. PMID:6401843
1983-01-13
Tanker-based production eyed for Gulf of Mexico use
Energy Technology Data Exchange (ETDEWEB)
The new oil price environment is sending industry engineers back to the drawing board. The search is on for cost effective and perhaps unconventional deepwater production systems. One candidate for Gulf of Mexico deepwater tracts is a tanker-based floating production, storage, and offloading (FPSO) system. Substantial experience with tanker-based FPSO systems has proven them to be cost effective when the field is remote from existing production facilities and pipelines. A tanker-based system offers the unique feature of integrating production, storage, and offloading capabilities into a single unit. Such systems can be installed in 12 to 15 months and can even be leased, significantly improving an operator's cash flow.
1986-05-01
Energy Technology Data Exchange (ETDEWEB)
Neopentane, because of its unique structural features, was found to be a useful probe for the assay of the acidity of various zeolites. The C-C bond was attacked by catalyst protons yielding CH/sub 4/ and the isobutyl carbenium ion in equal quantities. The latter either decomposed to produce isobutene or underwent secondary reactions. New avenues for reaction were opened with isobutane. The reaction of the Bronsted protons with the tertiary CH bonds produced H/sub 2/ and the same isobutyl carbenium ion. Hydride ion transfer of the same tertiary hydrogen to existing carbenium ions also occurred and the results showed that about half of the reaction was carried by this pathway. As with Neopentane, the C-C bond could also be attacked yielding the sec-propyl carbenium ion. These tools are being further developed.
1988-06-01
Structural analysis and modifications-2 tankers for offshore FPSO and FSO service
British Library Electronic Table of Contents (United Kingdom)
This paper addresses the unique structural requirements for successful conversion of tankers for floating production storage and offloading (FPSO) or floating storage and offloading (FSO) service. A description is given of the steps undertaken during two recent and very different conversions of a highly optimized 1980s VLCC to FPSO service, and a typical robust 1970s ULCC to FSO service. The paper describes the steps needed for ensuring the FPSO or FSO requirements are successfully met during conversion of the two tankers - each having its own history, e.g. date of build, original design, material choices, class society, voyage history and repairs. Firstly, the paper describes the procedure and results of an early initial structural assessment procedure on the basis of an American Bureau o...
2008-01-01
Spitzer Mid-infrared Study of Compact HII Regions in the Magellanic Clouds
We present a study of the mid-infrared properties and dust content of a sample of 27 HII ``blobs'', a rare class of compact HII regions in the Magellanic Clouds. A unique feature of this sample is that even though these HII regions are of high and low excitation they have nearly the same physical sizes ~1.5-3 pc. We base our analysis on archival 3-8 microns infrared imagery obtained with the Infrared Array Camera (IRAC) on board the Spitzer Space Telescope. We find that despite their youth, sub-solar metallicity and varied degrees of excitation, the mid-infrared colors of these regions are similar to those of typical HII regions. Higher excitation ``blobs'' (HEBs) display stronger 8 micron emission and redder colors than their low-excitation counterparts (LEBs).
2008-01-01
SnO2/graphene composite with high lithium storage capability for lithium rechargeable batteries
British Library Electronic Table of Contents (United Kingdom)
SnO2/graphene nanocomposites have been fabricated by a simple chemical method. In the fabrication process, the control of surface charge causes echinoid-like SnO2 nanoparticles to be formed and uniformly decorated on the graphene. The electrostatic attraction between a graphene nanosheet (GNS) and the echinoid-like SnO2 particles under controlled pH creates a unique nanostructure in which extremely small SnO2 particles are uniformly dispersed on the GNS. The SnO2/graphene nanocomposite has been shown to perform as a high capacity anode with good cycling behavior in lithium rechargeable batteries. The anode retained a reversible capacity of 634 mA?h?g?1 with a coulombic efficiency of 98% after 50 cycles. The high reversibility can be attributed to the mechanical buffering by the GNS against...
2010-01-01
Search for extended conformal algebra
International Nuclear Information System (INIS)
The authors search for the extended conformal algebra with two spin-s (s:integer) and one spin-1 generators. This search is inspired by the existence of chiral algebra in the Gaussian model for rational radius. For odd s, the conformal properties of the three-point functions imply that a general fusion rule can be reduced to those of the Gaussian model. For arbitrary even s, these conditions are weaker. In particular, for s = 2 the authors show that the chiral algebra of the Gaussian model is the unique extended conformal algebra with the value of the central charge fixed to be c = 1. It is also shown that the conformal generator is necessarily a bilinear of the spin-1 generator just as the Gaussian model. The authors conjecture that this remains true for arbitrary value of s.
1990-08-01
Safety philosophy and concepts for large liquid metal breeder reactor power plants
International Nuclear Information System (INIS)
This paper addresses the unique related aspects of the LMFBR concept which are of significance to containment design and structural analysis. Topics covered include: Primary boundary integrity assurance; Effects of sodium spills on integrity of structures; Provisions being considered for containment of melted cores; Fuel handling accidents. Specific reference is made to the FFTF and the Clinch River Breeder Reactor Project designs and methods of treatment of the above problems. In particular, the part played by tests, such as those carried out on a simulated FFTF model, and the planned structural reliability and related programs are considered. Where practicable, these topics are addressed in a manner which places FFTF and CRBR in context with other LMFBR's and point to a possible direction for future American LMFBR designs. (Auth.).
Safety philosophy and concepts for large liquid metal breeder reactor power plants
International Nuclear Information System (INIS)
This paper will adress the unique safety related aspects of the LMFBR concept which are of significance to containment design and structural analyses. Topics to be covered will include: primary boundary integrity assurance; effects of sodium spills on integrity of structures; provisions being considered for containment of melted cores; and fuel handling accidents. Specific reference will be made to the FFTF and the Clinch River Breeder Reactor Project designs and methods of treatment of the above problems. In particular, the part played by tests, such as those carried out on a simulated FFTF model, and the planned structural reliability and related programs will be considered. Where practicable, these topics will be addressed in a manner which places FFTF and CRBR in context with other LMFBR's, and will point to a possible direction for future American LMFBR designs.
1975-09-01
Energy Technology Data Exchange (ETDEWEB)
This study presents results from Monte Carlo radiation transport calculations aimed at characterizing a novel methodology being developed to detect partial defects in Pressurized Water Reactor (PWR) spent fuel assemblies (SFAs). The methodology uses a combination of measured neutron and gamma fields inside a spent fuel assembly in an in-situ condition where no movement of the fuel assembly is required. Previous studies performed on single isolated assemblies resulted in a unique base signature that would change when some of the fuel in the assembly is replaced with dummy fuel. These studies indicate that this signature is still valid in the in-situ condition enhancing the prospect of building a practical tool, Partial Defect Detector (PDET), which can be used in the field for partial defect detection.
2008-04-28
Robust curve fitting method for single binding site mass action model of radioimmunoassay
International Nuclear Information System (INIS)
The difficulty and unstability of the parameter estimation of mass action model for radioimmunoassay are the major obstacles to its application in routine work. A unique robust curve fitting method for the mass action model was introduced. large numbers of simulated data were generated with Monte Carlo method to compare the accuracy and robustness of the robust fitting and the least squre fitting (Marquardt method) of the mass action model. The results demonstrated that the new robusst method significantly increased the accuracy and reliability of data processing with the mass action model. It also markedly reduced the influence of outliers in the fitting of RIA data, and it was always 'convergent'. This robust method could also be applied to other mathematical models which can be transformed into high degree equations and no initial estimates are needed for curve fitting.
Resonant inelastic soft x-ray scattering of CdS: a two-dimensional electronic structure map approach
Energy Technology Data Exchange (ETDEWEB)
Resonant inelastic x-ray scattering (RIXS) with soft x-rays is uniquely suited to study the elec-tronic structure of a variety of materials, but is currently limited by low (fluorescence yield) count rates. This limitation is overcome with a new high-transmission spectrometer that allows to measure soft x-ray RIXS"maps." The S L2,3 RIXS map of CdS is discussed and compared with density functional calculations. The map allows the extraction of decay channel-specific"absorp-tion spectra," giving detailed insight into the wave functions of occupied and unoccupied elec-tronic states.
2008-09-24
Energy Technology Data Exchange (ETDEWEB)
The Nuclear Fuel Technology Department (NFTD) in CNRTC is a unique unit in Turkey in charge of performing all activities in nuclear fuel field. It has a pilot plant on uranium refining and conversion to UO{sub 2} since 1986. Presently, its R and D activities are focused on pellet manufacturing and characterization: UO{sub 2}, ThO{sub 2}and (Th,U)O{sub 2}. The studies on thorium dioxide fuel include to obtain ThO{sub 2} pellets from thorium nitrate and mixed (Th,U)O{sub 2} pellets. A study on evaluation of different fuel cycle options in accordance with nuclear energy planning in Turkey is also going on. (author)
1997-07-01
Reborn quadrant anode image sensor
International Nuclear Information System (INIS)
We describe a position sensitive photon counting microchannel plate based detector with an improved quadrant anode (QA) readout system. The technique relies on a combination of the four planar elements pattern and an additional fifth electrode. The charge cloud induced by single particle detection is split between the electrodes. The measured charge values uniquely define the position of the initial event. QA has been first published in 1976 by Lampton and Malina. This anode configuration was undeservedly forgotten and its potential has been hardly underestimated. The presented approach extends the operating spatial range to the whole sensitive area of the microchannel plate surface and demonstrates good linearity over the field of view. Therefore, the novel image sensor results in spatial resolution better then 50?m and count rates up to one million events per second.
2009-06-01
Reborn quadrant anode image sensor
British Library Electronic Table of Contents (United Kingdom)
We describe a position sensitive photon counting microchannel plate based detector with an improved quadrant anode (QA) readout system. The technique relies on a combination of the four planar elements pattern and an additional fifth electrode. The charge cloud induced by single particle detection is split between the electrodes. The measured charge values uniquely define the position of the initial event. QA has been first published in 1976 by Lampton and Malina. This anode configuration was undeservedly forgotten and its potential has been hardly underestimated. The presented approach extends the operating spatial range to the whole sensitive area of the microchannel plate surface and demonstrates good linearity over the field of view. Therefore, the novel image sensor results in spatial...
2009-01-01
Real-time orbit feedback at the APS.
Energy Technology Data Exchange (ETDEWEB)
A real-time orbit feedback system has been implemented at the Advanced Photon Source in order to meet the stringent orbit stability requirements. The system reduces global orbit motion below 30Hz by a factor of four to below 5{micro}m rms horizontally and 2{micro}m rms vertically. This paper focuses on dynamic orbit stability and describes the all-digital orbit feedback system that has been implemented at the APS. Implementation of the global orbit feedback system is described and its latest performance is presented. Ultimately, the system will provide local feedback at each x-ray source point using installed photon BPMs to measure x-ray beam position and angle directly. Technical challenges associated with local feedback and with dynamics of the associated corrector magnets are described. The unique diagnostic capabilities provided by the APS system are discussed with reference to their use in identifying sources of the underlying orbit motion.
1998-06-18
Quasienergy description of the driven Jaynes-Cummings model
We analyze the driven resonantly coupled Jaynes-Cummings model in terms of a quasienergy approach by switching to a frame rotating with the external modulation frequency and by using the dressed atom picture. A quasienergy surface in phase space emerges whose level spacing is governed by a rescaled effective Planck constant. Moreover, the well-known multiphoton transitions can be reinterpreted as resonant tunneling transitions from the local maximum of the quasienergy surface. Most importantly, the driving defines a quasienergy well which is nonperturbative in nature. The quantum mechanical quasienergy state localized at its bottom is squeezed. In the Purcell limited regime, the potential well is metastable and the effective local temperature close to its minimum is uniquely determined by the squeezing factor. The activation occurs in this case via dressed spin flip transitions rather than via quantum activation as in other driven nonlinear quantum systems such as ...
2010-01-01
International Nuclear Information System (INIS)
The Argyle pipe occurring in the East Kimberley Province of Western Australia is a unique, highly-diamondiferous lamproite. Although it resembles other lamproites located in the West Kimberley Province with respect to its setting, structure, petrography and geochemistry, it is probably Proterozoic in age and hence substantially older than Tertiary occurrences of the West Kimberley Province. Rb-Sr measurements on whole rock and phlogopite samples from magmatic olivine-phlogopite lamproite, reveals a two point model age of 1126 +- 9 Ma for the Argyle pipe. This age is consistent with ages of other, similar volcanic igneous rocks occurring in several localities worldwide. The widespread occurrence of Proterozoic kimberlites and lamproites suggests that this was an important period of worldwide alkalic intrusive activity.
International Nuclear Information System (INIS)
Extraskeletal Ewing's sarcoma (ES) and primitive neuroectodermal tumor (PNET) are widely regarded as clinically and histologically identical tumors which consist of small blue round cells. Extraskeletal ESs/PNETs usually occur in the deep soft tissues of the paraspinal region, chest wall, or lower extremities. However, superficially located cases, so-called cutaneous ESs/PNETs, are exceedingly rare, and the vast majority of the reported cases present as a single small mass. We present magnetic resonance imaging (MRI) findings and clinical course of a unique case of primary cutaneous ES/PNET presenting as numerous huge masses with severe ulceration on them. (orig.)
2010-06-01
Premnalatifolin A, a novel dimeric diterpene from Premna latifolia Roxb
British Library Electronic Table of Contents (United Kingdom)
Premnalatifolin A (1), a unique icetexane diterpene dimer was isolated from the stem-bark of Indian medicinal plant, Premna latifolia. Its structure and relative stereochemistry were elucidated on the basis of detailed spectroscopic analysis, including HRESIMS and 2D NMR (COSY, HSQC, HMBC, and NOESY) spectra. The compound has dimeric carbon skeleton composed of two icetexane skeletal diterpenes linked via ether bond. Further, premnalatifolin A (1) was also evaluated for its cytotoxicity against cancer cell lines (HT-29, A-431, MCF-7, Hep-G2, PC-3, A-549, B-16 F10, and ACHN), which displayed potent activity against HT-29 and MCF-7 cell lines with the IC50 values of 12.15 and 1.11mg/mL, respectively.
2011-01-01
Pickup and delivery network segmentation using contiguous geographic clustering
British Library Electronic Table of Contents (United Kingdom)
This paper addresses the problem of partitioning a local service region into nonoverlapping work areas in which pickups and deliveries are made throughout the day. For a fleet of homogeneous vehicles, a given set of customers, and expected demand for service, the objective is to find the least number of work areas or clusters that satisfy a variety of geometric and capacity constraints. Using rectangles as the basic shape, each cluster must have an aspect ratio that falls within certain bounds, as well as meet load and time requirements dictated by the capacity of a vehicle and the working hours in a day, respectively. The latter requirement presents a unique hurdle because travel times are a function of the actual routes followed by the drivers, and are not known, even in a probabilistic ...
2011-01-01
In 1934, Reinhardt asked for the centrally symmetric convex domain in the plane whose best lattice packing has the lowest density. He conjectured that the unique solution up to an affine transformation is the smoothed octagon (an octagon rounded at corners by arcs of hyperbolas). This article offers a detailed strategy of proof. In particular, we show that the problem is an instance of the classical problem of Bolza in the calculus of variations. A minimizing solution is known to exist. The boundary of every minimizer is a differentiable curve with Lipschitz continuous derivative. If a minimizer is piecewise analytic, then it is a smoothed polygon (a polygon rounded at corners by arcs of hyperbolas). To complete the proof of the Reinhardt conjecture, the assumption of piecewise analyticity must be removed, and the conclusion of smoothed polygon must be strengthened to smoothed octagon.
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
Cuphea, a relatively unknown plant outside the scientific community, might someday provide valuable oils for manufacturing soaps, detergents, surfactants, and lubricants, and may have medical, nutritional and dietetic applications as well. Unique properties of oils found in its seed make cuphea a potentially valuable new crop for the USA. Its seeds contain large quantities of medium-chain fatty acids such as lauric acid, which is used in manufacturing soaps and detergents. Other medium-chain fatty acids in cuphea can be used for clinical treatment of rare human ailments associated with fat absorption. New uses for the fatty acids in the seed may be developed and economic conditions may change, making the crop more or less valuable.
1986-02-01
Energy Technology Data Exchange (ETDEWEB)
This paper presents results, numeric and experimental, due to installation operation of a Risers Uphold Sub-Surface Buoy, (BSR). This kind of installation developed by PETROBRAS is unique in the world. The work of BSR installation was based on a numeric pre analysis to verify the system and determine the main parameters to be experimentally verified. The second phase of the work was the experimental analysis in a deep water ocean basin. s. The work describes the BSR and their main accessories, the experimental environment and the model constructed in aluminum in a 1:12 scale and the main results. (author)
2004-07-01
Nuclear data interface retrospective
Energy Technology Data Exchange (ETDEWEB)
The Nuclear Data Interface (NDI) code library and data formats are the standards for multigroup nuclear data at Los Alamos National Laboratory. NDI's analysis, design, implementation, testing, integration, and maintenance required a ten person-year and ongoing effort by the Nuclear Data Team. Their efforts provide a unique, contemporary experience in producing a standard component library. In reflection upon that experience at NDI's decennial, we have identified several factors critical to NDI's success: it addressed real problems with appropriate simplicity, it fully supported all users, it added extra value through the code to the raw nuclear data, and its team went the distance from analysis through maintenance. In this report we review these critical success factors and discuss their implications for future standardization projects.
2008-01-01
Novel Processing of Unique Ceramic-Based Nuclear Materials and Fuels
Energy Technology Data Exchange (ETDEWEB)
Advances in nuclear reactor technology and the use of gas-cooled fast reactors require the development of new materials that can operate at the higher temperatures expected in these systems. These include refractory alloys base on Nb, Zr, Ta, Mo, W, and Re; ceramics and composites such as those based on silicon carbide (SiCf-SiC); carbon-carbon composites; and advanced coatings. Besides the ability to handle higher expected temperatures, effective heat transfer between reactor componets is necessary for improved efficiency. Improving thermal conductivity of the materials used in nuclear fuels and other temperature critical components can lower the center-line fuel temperature and thereby enhance durability and reduce the risk of premature failure.
2008-11-30
New developments in the Electric Fuel Ltd. zinc/air system
Energy Technology Data Exchange (ETDEWEB)
Electric Fuel Ltd. is engaged in the design, development and commercialization of its proprietary zinc/air battery technology for electric vehicles, consumer electronic products and defence applications. To meet the challenging requirements for propelling an all-electric bus, the Vehicle Division sought a unique solution: an all electric battery-battery hybrid propulsion system. The high energy zinc/air battery is coupled with a high-power auxiliary battery. The combined system offers zero emission, high power and long range in an economically viable package. The consumer battery group has developed a high power primary zinc/air cell aimed at cellular phone users, offering extended use, convenience and low cost. (orig.)
1999-07-01
Neutron cross-sections for next generation reactors: New data from n_TOF
International Nuclear Information System (INIS)
In 2002, an innovative neutron time-of-flight facility started operation at CERN: n_TOF. The main characteristics that make the new facility unique are the high instantaneous neutron flux, high resolution and wide energy range. Combined with state-of-the-art detectors and data acquisition system, these features have allowed to collect high accuracy neutron cross-section data on a variety of isotopes, many of which radioactive, of interest for Nuclear Astrophysics and for applications to advanced reactor technologies. A review of the most important results on capture and fission reactions obtained so far at n_TOF is presented, together with plans for new measurements related to nuclear industry.
2008-06-22
Network management of real-time embedded processors
International Nuclear Information System (INIS)
The Superconducting super Collider Laboratory is a complex of particle accelerators being built in Ellis County, Texas. It will have a dedicated global communications network that will deliver control messages and provide for general data acquisition. This network will connect thousands of computer nodes over a very large geographic area. In order to meet the demanding availability requirements being levied on the system, it will need comprehensive network management. A large number of the computer nodes are embedded systems that traditionally do not support network management services. This presents unique challenges to standard network management practices. The Simple Network Management Protocol, SNMP, is widely accepted by industry as a tool to manage network devices. In this paper the authors examine the performance characteristics and usefulness of an SNMP agent in a real-time environment.
1993-05-17
British Library Electronic Table of Contents (United Kingdom)
This paper investigates various usages of natural gas (NG) as an energy source for different hydrogen production technologies. A comparison is made between the different methods of hydrogen production, based on the total amount of natural gas needed to produce a specific quantity of hydrogen, carbon dioxide emissions per mole of hydrogen produced, water requirements per mole of hydrogen produced, and a cost sensitivity analysis that takes into account the fuel cost, carbon dioxide capture cost and a carbon tax. The methods examined are the copper-chlorine (Cu-Cl) thermochemical cycle, steam methane reforming (SMR) and a modified sulfur-iodine (S-I) thermochemical cycle. Also, an integrated Cu-Cl/SMR plant is examined to show the unique advantages of modifying existing SMR plants with new h...
2010-01-01
Monolayers at air-water interfaces: from origins-of-life to nanotechnology
British Library Electronic Table of Contents (United Kingdom)
Abstract The air-water interface presents several interesting features, namely a) a molecularly flat environment, b) a boundary region between two phases with different dielectric constants, c) permits or promotes dynamic interactions within the interface region, and d) a point of interaction between hydrophobic compounds and aqueous molecules. Accordingly, Langmuir monolayers at the air-water interface have several unique characteristics and properties, which require investigation. In this review-type personal account, typical examples of molecular recognition and molecular patterning at air-water interfaces are first introduced, followed by descriptions of specific and unusual properties of monolayers on water. In addition, two examples of our own results concerning Langmuir monolayers a...
2011-01-01
Model for simulation of freezing and thawing processes in building materials
Energy Technology Data Exchange (ETDEWEB)
This paper presents a mathematical model for simultaneous heat and moisture transfer under freezing-thawing in porous hygroscopic material. Even below O{sup o}C, unfrozen liquid water exists in the material which plays an important role in the processes. The model takes into account the existence of unfrozen liquid water. The system is treated as a three-(gas, liquid and solid) phase system of water. Moisture chemical potential is used as a moisture potential. Under freezing, moisture chemical potential is a unique function of local temperature. So, during freezing, two unknown variables to be solved are solid water content and moisture potential or temperature. A simple example of simulation for freezing processes is shown. (author)
2001-07-01
Methods for proving the equivalency of detonator performance
Energy Technology Data Exchange (ETDEWEB)
One of the challenges facing engineers is developing newer, safer detonators that are equivalent to devices currently in use. There is no clear consensus on an exact method for drawing equivalence of detonators. This paper summarizes our current efforts to develop diagnostics addressing various aspects of detonator design to better quantify and prove equivalency. We consider various optical techniques to quantify the output pressure and output wave shape. The development of a unique interpretation of streak camera breakouts, known as the apparent center of initiation, will be discussed as a metric for detonation wave shape. Specific examples apply these techniques to the comparison of a new laser-driven detonator with an existing exploding bridgewire (EBW) detonator. Successes and short-comings of the techniques will be discussed.
2009-01-01
Method and device for identifying different species of honeybees
Energy Technology Data Exchange (ETDEWEB)
A method and device have been provided for distinguishing Africanized honeybees from European honeybees. The method is based on the discovery of a distinct difference in the acoustical signatures of these two species of honeybees in flight. The European honeybee signature has a fundamental power peak in the 210 to 240 Hz range while the Africanized honeybee signature has a fundamental power peak in the 260 to 290 Hz range. The acoustic signal produced by honeybees is analyzed by means of a detecting device to quickly determine the honeybee species through the detection of the presence of frequencies in one of these distinct ranges. The device includes a microphone for acoustical signal detection which feeds the detected signal into a frequency analyzer which is designed to detect the presence of either of the known fundamental wingbeat frequencies unique to the acoustical signatures of these species as an indication of the identity of the species and indicate the ...
1989-01-01
Mental time travel and the shaping of language.
Episodic memory can be regarded as part of a more general system, unique to humans, for mental time travel, and the construction of future episodes. This allows more detailed planning than is afforded by the more general mechanisms of instinct, learning, and semantic memory. To be useful, episodic memory need not provide a complete or even a faithful record of past events, and may even be part of a process whereby we construct fictional accounts. The properties of language are aptly designed for the communication and sharing of episodes, and for the telling of stories; these properties include symbolic representation of the elements of real-world events, time markers, and combinatorial rules. Language and mental time travel probably co-evolved during the Pleistocene, when brain size increased dramatically. PMID:18641975
2008-07-19
Literary Lives and a Literal Death: Yajnavalkya, Sakalya, and an Upaniṣadic Death Sentence
British Library Electronic Table of Contents (United Kingdom)
One of the most popular stories found in the Upani?ads centers around a debate between the ritualist and philosopher, Yajnavalkya, and a series of interlocutors about the nature of sacrifice, the self, and the cosmos. This story, from a textual-historical perspective, is unique in that the last interlocutor, Sakalya, is said to die by having his head shatter because he is unable to answer a question about the fundamental nature of immortality. In this paper, I analyze the interrelationship of these two main characters and argue that this relationship is one key to not only understanding the portrayal of these characters, but also the larger import of this debate about immortality. I provide an intratextual rationale for the head-shattering conclusion and discuss how character and d...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
The advent of carbon nanotubes, which are graphite layers convoluted in cylinders several nanometers in diameter and several micrometers in length, as well as the experiments on implanting metal atoms in such tubes open the way to producing nanoconductors and other materials with unique properties. For theorists, the basic challenge is interpreting and predicting the structure and properties of these systems. The linearized augmented-plane-wave method (LAPW) is one of the most accurate methods in the theory of the electronic structure of solids. A generalization of this method for quasi-two-dimensional systems, surface electronic states, and layered crystals is known. The LAPW theory for quasi-unidimensional systems, which exhibit translational symmetry in one direction, has been absent thus far. In this paper, the authors suggest a version of such a theory and use this method to calculate the electronic structure of carbyne (a linear chain of carbon atoms) and ...
1995-10-01
British Library Electronic Table of Contents (United Kingdom)
Human breast milk samples collected in 2007?2008 from four countries, Vietnam (Hanoi), China (Beijing), Korea (Seoul) and Japan (Sendai, Kyoto and Takayama), were analyzed for persistent organic pollutants (POPs) such as dichlorodiphenyltrichloroethane and its metabolites (DDTs), chlordane-related compounds (CHLs), hexachlorocyclohexanes (HCHs), hexachlorobenzene (HCB), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs). Comparing with previous surveys, the present study indicates that the DDTs in breast milk from China and Vietnam had gradually decreased during the last decade, but were still 5?10 times higher than those in other nations. The ratios of p,p?-DDE/p,p?-DDT and o,p?-DDT/p,p?-DDT were higher in Beijing than in the other countries, suggesting that there...
2009-01-01
British Library Electronic Table of Contents (United Kingdom)
Abstract In this article, I investigate the relation between economic inequality and the decision to take up studies at the tertiary level late in life. Who exactly decides to enrol? Is it advantaged or disadvantaged groups in terms of current earnings rank, occupation, unemployment experience and social origin? Using unique register data of university applications and discrete time hazard regression models, the results show the likelihood of a late entry to be especially high for individuals who are disadvantaged to a moderate extent in terms of current earnings rank and also with some unemployment experience. Class differences in the transition to tertiary education decline with age. This suggests, with a moderate amount of simplification, that lifelong learning tends to promote both int...
2011-01-01
Laser application in the fabrication of gas-tagged capsules. A leak detection system
Energy Technology Data Exchange (ETDEWEB)
Encapsulation of a unique isotopic blend of krypton and xenon gas employs a special application of laser technology. The encapsulated gas is then used as the primary medium for detection and identification of failed nuclear fuel rods. The use of gas tagging as a means of detecting and identifying failed nuclear fuel rods has been successfully demonstrated and used by the Argonne National Laboratory, Experimental Breeder Reactor (EBR-2) Project, and the Westinghouse Hanford Company (WHC), Fast Flux Test Facility (FFTF) Fast Breeder Reactor Program. The Power Reactor and Nuclear Fuel Development Corporation (PNC) of Japan has selected this leak detection system for use in their MONJU Prototype Reactor fuel assemblies. The MONJU reactor is almost identical in design to the highly successful FFTF reactor, which is currently in standby status.
1993-12-01
Energy Technology Data Exchange (ETDEWEB)
Ozone plays a critical role in both the chemistry and radiation balance of the troposphere. Understanding the factors controlling tropospheric ozone levels is critical to our understanding of a variety of issues in global chemistry and climate change. Chlorine atoms have the potential to contribute significantly to the ozone balance in the free troposphere. They can react directly with ozone or alternately, with organics and may actually lead to the formation of ozone in the presence of sufficient NO. Reactions of alkali halides in sea salt particles are a potential source of atomic chlorine, hence reactions of these alkali halides, especially those producing precursors to atomic chlorine, are of great interest. Finally, the mechanisms, intermediates and products of the Cl-biogenic reactions are unknown; these could serve as unique markers of chlorine atom chemistry in the troposphere, and hence are important to define.
1994-11-15
British Library Electronic Table of Contents (United Kingdom)
Many existing agents for diabetes therapy are unable to restore or maintain normal glucose homeostasis or prevent the eventual emergence of hyperglycemia-related complication. Therefore, agents based on novel mechanisms are sought to complement and extend the current therapeutic approaches. Based on the initial paper research, we focused on active STAT3 as an attractive pharmacological target for type 2 diabetes. The subsequent text mining with a unique query to identify suppressors but not activators of STAT3 revealed the ERK2/STAT3 pathway as a novel diabetes target. The description of ERK2 inhibitors as diabetes target had not been found in our text mining research at present. The mechanism-based peptide inhibitor for ERK2 was identified using the knowledge of the KIM sequence, which ha...
2011-01-01
Isolation and characterization of microsatellite markers in Acca sellowiana (Berg) Burret.
Acca sellowiana has commercial potential because of the quality and the unique flavor of its fruit. Conservation of natural populations and management of breeding programmes would benefit from the availability of molecular markers that could be used to characterize levels and distribution of genetic variability. Thus, 13 microsatellite markers were developed from an enriched genomic library of A. sellowiana. They were characterized using 40 samples. The expected and observed heterozygosities ranged from 0.513 to 0.913 and from 0.200 to 0.889, respectively. These are the first microsatellite loci characterized from A. sellowiana that will contribute to improve researches on the genetic conservation, characterization and breeding. PMID:21586063
2008-07-08
Energy Technology Data Exchange (ETDEWEB)
The present study is devoted to the investigation of the mechanism of aluminium nitriding by a technique that employs implantation of low-energy nitrogen ions and diffusional transport of atoms. The nitriding of aluminium is investigated, because this is a method for surface modification of aluminium and has a potential for application in a broad spectrum of fields such as automobile, marine, aviation, space technologies, etc. However, at present nitriding of aluminium does not find any large scale industrial application, due to problems in the formation of stoichiometric aluminium nitride layers with a sufficient thickness and good quality. For the purposes of this study, ion nitriding is chosen, as an ion beam method with the advantage of good and independent control over the process parameters, which thus can be related uniquely to the physical properties of the resulting layers. Moreover, ion nitriding has a close similarity to plasma nitriding and plasma ...
2002-09-01
Introduction to Big Bang nucleosynthesis: open and closed models, anisotropies
Energy Technology Data Exchange (ETDEWEB)
A variety of observations suggest that the Universe had a hot dense origin and that the pregalactic composition of the Universe was determined by nuclear reactions that occurred in the first few minutes. There is no unique hot Big Bang theory, but the simplest version produces a primeval chemical composition that is in good qualitative agreement with the abundances deduced from observation. Whether or not any Big Bang theory will provide quantitative agreement with observations depends on a variety of factors in elementary particle physics (number and masses of stable or long-lived particles, half-life of neutron, structure of grand unified theories) and from observational astronomy (present mean baryon density of the Universe, the Hubble constant and deceleration parameter). The influence of these factors on the abundances is discussed, as is the effect of departures from homogeneity and isotropy in the early Universe.
1982-10-15
Inspection pig for gas pipeline
Energy Technology Data Exchange (ETDEWEB)
The ultrasonic inspection pig system was described as being under development. This system was said to adopt the unique wheel type ultrasonic sensor which does not need couplant. This pig was designed to detect external corrosion in long-distance pipelines without interruption of the gas service. The wall-thickness measurement performance test and the travel performance test of the inspection pig in the test line confirmed that these performances satisfied the development specifications. However, the effect induced by the inner surface properties of the pipe and the influence of the pipe`s performance over long distances and for a long period of time still needed to be verified in an actual gas pipeline, and while the pipeline was actually in service. Improvements to the prototype model of the inspection pig were expected to include combinations of inspection pigs, with increases in battery and memory capacities to permit them to cope with in increased number of ...
1992-12-31
Insights from Development of Regulatory PSA Model for SMART
International Nuclear Information System (INIS)
SMART (System-Integrated Modular Advanced Reactor) is a first-of-the-kind integral reactor with 330 MW thermal power under active development by Korea Atomic Energy Research Institute (KAERI) for power generation and seawater desalination. SMART employs various design features that are not typically found in other nuclear power plants. Examples include a unique passive residual heat removal system (PRHRS), and enclosure of a pressurizer, eight helical steam generators, and eight canned reactor coolant pumps inside the reactor pressure vessel. This paper presents risk insights on the SMART reactor gained during the development of a regulatory PSA model by Korea Institute of Nuclear Safety (KINS)
2010-10-01
Energy Technology Data Exchange (ETDEWEB)
Hyaluronic acid (HA), a principal matrix molecule in many tissues, is present in high amounts in articular cartilage. HA contributes in unique ways to the physical behavior of the tissue, and has been shown to have beneficial effects on chondrocyte activity. The goal of this study was to incorporate graduated amounts of HA into type I collagen scaffolds for the control of chondrocyte-mediated contraction and chondrogenesis in vitro. The results demonstrated that the amount of contraction of HA/collagen scaffolds by adult canine articular chondrocytes increased with the HA content of the scaffolds. The greatest amount of chondrogenesis after two weeks was found in the scaffolds which had undergone the most contraction. HA can play a useful role in adjusting the mechanical behavior of tissue engineering scaffolds and chondrogenesis in chondrocyte-seeded scaffolds.
2007-09-15
Energy Technology Data Exchange (ETDEWEB)
Current Intrusion Detection System (IDS) technology is not suited to be widely deployed inside a Supervisory, Control and Data Acquisition (SCADA) environment. Anomaly- and signature-based IDS technologies have developed methods to cover information technology-based networks activity and protocols effectively. However, these IDS technologies do not include the fine protocol granularity required to ensure network security inside an environment with weak protocols lacking authentication and encryption. By implementing a more specific and more intelligent packet inspection mechanism, tailored traffic flow analysis, and unique packet tampering detection, IDS technology developed specifically for SCADA environments can be deployed with confidence in detecting malicious activity.
2008-05-01
ISR; A database for symbolic processing in computer vision
Energy Technology Data Exchange (ETDEWEB)
Computer vision imposes unique requirements on the representation and manipulation of image data and knowledge. At a vision system's lowest level are sensors that represent an image with purely numeric image arrays, while at the highest level are semantic world models that provide the final interpretation of the scene. In between are thousands of intermediate descriptions, many of which must be repeatedly accessed and processed during interpretation. In this article, the authors describe a representation and management system for use at the intermediate (symbolic) level of vision. Based on database management methodology, the intermediate symbolic representation (ISR) mediates access to intermediate-level vision data and forms an active interface to the higher-level inference processes that construct an image's interpretation. The system supports important types of data and operations and can be adapted to the changing needs of ongoing research. ...
1989-12-01
IS CORPORATE R&D INVESTMENT IN HIGH-TECH SECTORS MORE EFFECTIVE?
British Library Electronic Table of Contents (United Kingdom)
This paper discusses the link between R&D and productivity across the European industrial and service sectors. The empirical analysis is based on both the European sectoral OECD data and on a unique micro-longitudinal database consisting of 532 top European R&D investors. The main conclusions are as follows. First, the R&D stock has a significant positive impact on labor productivity; this general result is largely consistent with previous literature in terms of the sign, the significance, and the magnitude of the estimated coefficients. More interestingly, both at sectoral and firm levels the R&D coefficient increases monotonically (both in significance and magnitude) when we move from the low-tech to the medium- and high-tech sectors. This outcome means that corporate R&D investment is m...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
Long-term fishery datasets can provide valuable insights into fishing histories, and represent a baseline against which to examine current status and plan for future management. For coral reef-associated fisheries, however, such datasets are extremely rare. We analyse a unique 45-year set of landings data on six reef fishes of commercial importance in Cubas coastal fisheries, together with information on management interventions, and examine the likely implications of over-fishing and management on the long-term condition of one grouper (Serranidae) and five snapper (Lutjanidae) species. The data clearly demonstrate differential responses to fishing and management according to the biology of the different species examined. In particular, those species that aggregate most predictably, and a...
2009-01-01
British Library Electronic Table of Contents (United Kingdom)
A highly efficient integrated energy conversion system is built based on a methane catalytic decomposition reactor (MCDR) together with a direct carbon fuel cell (DCFC) and an internal reforming solid oxide fuel cell (IRSOFC). In the MCDR, methane is decomposed to pure carbon and hydrogen. Carbon is used as the fuel of DCFC to generate power and produce pure carbon dioxide. The hydrogen and unconverted methane are used as the fuel in the IRSOFC. A gas turbine cycle is also used to produce more power output from the thermal energy generated in the IRSOFC. The output performance and efficiency of both the DCFC and IRSOFC are investigated and compared by development of exact models of them. It is found that this system has a unique loading flexibility due to the good high-loading property of ...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
Determination of the maximum temperature and temperature distribution along the rake face of the cutting tool is of particular importance because of its controlling influence on tool life, as well as, the quality of the machined part. Numerous attempts have been made to approach the problem with different methods including experimental, analytical and numerical analysis. Although considerable research effort has been made on the thermal problem in metal cutting, there is hardly a consensus on the basics principles. The unique tribological contact phenomenon, which occur in metal cutting is highly localized and non-linear, and occurs at high temperatures, high pressures and high strains. This has made it extremely difficult to predict in a precise manner or even assess the performance of va...
2006-01-01
Head pose estimation in computer vision: a survey.
The capacity to estimate the head pose of another person is a common human ability that presents a unique challenge for computer vision systems. Compared to face detection and recognition, which have been the primary foci of face-related vision research, identity-invariant head pose estimation has fewer rigorously evaluated systems or generic solutions. In this paper, we discuss the inherent difficulties in head pose estimation and present an organized survey describing the evolution of the field. Our discussion focuses on the advantages and disadvantages of each approach and spans 90 of the most innovative and characteristic papers that have been published on this topic. We compare these systems by focusing on their ability to estimate coarse and fine head pose, highlighting approaches that are well suited for unconstrained environments. PMID:19229078
2009-04-01
Geomechanical numerical simulations of complex geologic structures
Energy Technology Data Exchange (ETDEWEB)
Ability to predict mechanical response of rock in three dimensions over the spatial and time scales of geologic interest would give the oil and gas industry the ability to reduce risk on prospects, improve pre-project initial reserve estimates, and lower operating costs. A program has recently been initiated, under the auspices of the Advanced Computational Technology Initiative (ACTI), to achieve such a computational technology breakthrough by adapting the unique advanced quasistatic finite element technology developed by Sandia to the mechanics applications important to exploration and production activities within the oil and gas industry. As a precursor to that program, in an effort to evaluate the feasibility of the approach, several complex geologic structures of interest were analyzed with the existing two-dimensional quasistatic finite element code, SANTOS, developed at Sandia. Examples are presented and discussed.
1996-05-01
Fundamental concepts of digital image processing
The field of a digital-image processing has experienced dramatic growth and increasingly widespread applicability in recent years. Fortunately, advances in computer technology have kept pace with the rapid growth in volume of image data in these and other applications. Digital image processing has become economical in many fields of research and in industrial and military applications. While each application has requirements unique from the others, all are concerned with faster, cheaper, more accurate, and more extensive computation. The trend is toward real-time and interactive operations, where the user of the system obtains preliminary results within a short enough time that the next decision can be made by the human processor without loss of concentration on the task at hand. An example of this is the obtaining of two-dimensional (2-D) computer-aided tomography (CAT) images. A medical decision might be made while the patient is still under observation rather ...
1983-03-01
Flue-gas desulfurization inspection and performance evaluation. Manual
Energy Technology Data Exchange (ETDEWEB)
The intent of this manual is to provide inspectors from Federal and state environmental agencies with information regarding the problems that plague lime/limestone slurry flue-gas desulfurization (FGD) systems that will aid them in their inspections and performance evaluations of these systems with respect to compliance with the emission standards that have evolved since the passage of the 1970 Clean Air Act. A unique feature of the manual is its structure as a tool, or working document, which will accompany the inspector on each plant inspection. Thus, the document is presented in user friendly fashion and tailored to provide practical information for its intended use--to assist in the systematic inspection of an FGD system to determine present and future compliance status. The approach entails the use of nomographs, checklists, matrices, simplified diagrams, cross-referencing, and indexing of textual information, and the presentation of important guidelines and ...
1985-10-01
British Library Electronic Table of Contents (United Kingdom)
Future climate change will likely influence the frequency and intensity of weather extremes. As such events are by definition rare, long records are required to understand their characteristics, drivers, and consequences on ecology and society. Herein we provide a unique perspective on regional-scale temperature extremes over the past millennium, using three tree-ring maximum latewood density (MXD) chronologies from higher elevations in the European Alps. We verify the tree-ring-based extremes using documentary evidences from Switzerland, the Czech Republic, and Central Europe that allowed the identification of 44 summer extremes over the 1550-2003 period. These events include cold temperatures in 1579, 1628, 1675, and 1816, as well as warm ones in 1811 and 2003. Prior to 1550, we provide ...
2010-01-01
Fault location observability analysis and optimal meter placement based on voltage measurements
British Library Electronic Table of Contents (United Kingdom)
Various transmission line fault location algorithms have been proposed in the past depending on measurements available. These methods evince that if a sufficient number of meters are placed in a power network to record the fault measurements, then the fault location can be reliably estimated. A relevant question to ask may be: how many meters are sufficient in order to derive a reliable and unique fault location estimate for a given network? This paper addresses this question by defining and performing the fault location observability analysis. An optimal meter placement scheme is proposed for determining the optimal locations to place meters so as to make the system observable while minimizing the required number of meters to reduce costs. The proposed method is especially useful for powe...
2009-01-01
Familial unilateral deafness and delayed endolymphatic hydrops
British Library Electronic Table of Contents (United Kingdom)
Delayed endolymphatic hydrops (DEH) is a unique disorder characterized by fluctuating otologic symptoms in the setting of preexisting unilateral deafness. The symptoms include aural fullness, fluctuating hearing, and/or episodes of vertigo similar to those observed in Meniere disease and may occur ipsilateral or contralateral to the previously deafened ear. In most reported cases, the unilateral deafness has been a profound sensorineural hearing loss with a sudden onset that has been variously attributed to bacterial or viral labyrinthitis, acoustic or cranial trauma, otosclerosis, and congenital CMV infection. Familial occurrence of the syndrome has not previously been reported in the literature. In this report, we describe two possible familial instances of delayed DEH. These patients ra...
2007-01-01
FFTF [Fast Flux Test Facility] management
International Nuclear Information System (INIS)
Fuel Management at the Fast Flux Test Facility (FFTF) involves more than just the usual ex-core and in-core management of standard fuel and non-fuel components between storage locations and within the core since it is primarily an irradiation test facility. This mission involves testing an ever increasing variety of fueled and non-fueled experiments, each having unique requirements on the reactor core as well as having its own individual impact on the reload design. This paper describes the fuel management process used by the Westinghouse Hanford Company Core Engineering group that has led to the successful reload design of nine operating cycles and the irradiation of over 120 tests.
1987-09-13
British Library Electronic Table of Contents (United Kingdom)
Plasma polymerization of aniline is carried out in a radiofrequency plasma reactor and the effect of polymerization time is examined in the structural, optical and optoelectronic properties of deposited films. Conjugated structures of polyaniline like films are obtained with unique and broad optical absorption band in the ultraviolet and entire visible region. The width of the absorption band increases and hence the optical band gap decreases with polymerization time. The optical constants are extracted by Swanepoel method and the optical dispersion parameters are determined by employing the Wemple-DiDomenico single oscillator model. The films exhibit similar thermal stability in air and argon atmosphere in the region of interest for optoelectronic applications. The photoluminescence study...
2011-01-01
Energy Technology Data Exchange (ETDEWEB)
In Haiti, and other semiarid regions of the world, the need for fuelwood and forage is critical. The report summarizes research conducted over a ten year period on developing replicable plantations of leguminous trees in semiarid lands, especially in areas near seawater salinity levels. Research included greenhouse and laboratory work followed by field trials in Haiti and focused on two species: Prosopis and Leucaena. (Acacia is mentioned in the report's title but not in the report itself.) Results were as follows. (1) Greenhouse experiments identified leaf diagnostic criteria indicating mineral nutrient deficiencies in field trees. It also established the importance of micronutrients, especially zinc, in permitting growth in high pH (9.0) soils.
1992-01-01
British Library Electronic Table of Contents (United Kingdom)
Academic, government, and industrial field researchers have generated a significant database of field studies of the volatility of soil applied fumigants. However, limited work exists in validating physical models against field volatility data sets and fully exploring the volatility parametric response surface. Field studies quantifying atmospheric flux for soil fumigants 1,3-dichloropropene and chloropicrin are validated against the United States Department of Agriculture (USDA Salinity Laboratory) soil physics model CHAIN_2D that was modified specifically for agronomic uses of soil fumigants. Comparison between model predictions and field observations for six unique field trials in five different states indicate that CHAIN_2D effectively captures the magnitude and duration of fumigant em...
2010-01-01
British Library Electronic Table of Contents (United Kingdom)
A fragmented fossil bone incised with the figure of a proboscidean was recently found at Vero Beach, Florida near the location where Late Pleistocene fauna and human bones were recovered from 1913 to 1916. This engraving may represent the oldest and only existing example of Terminal Pleistocene art depicting a proboscidean in the Americas. Because of the uniqueness, rarity, and potential antiquity of this specimen, caution demanded that a variety of tests be used in an attempt to verify its authenticity. The mineralized bone was identified as mammoth, mastodon, or giant sloth. Rare earth element analysis was consistent with the fossil bone being ancient and originating at or near the Old Vero site (8-IR-9). Forensic analysis suggests the markings on the bone are not recent. Optical microsc...
2011-01-01
EPRI-USDOE COOPERATIVE AGREEMENT: COFIRING BIOMASS WITH COAL
Energy Technology Data Exchange (ETDEWEB)
The entire Electric Power Research Institute (EPRI) cofiring program has been in existence of some 9 years. This report presents a summary of the major elements of that program, focusing upon the following questions: (1) In pursuit of increased use of renewable energy in the US economy, why was electricity generation considered the most promising target, and why was cofiring pursued as the most effective near-term technology to use in broadening the use of biomass within the electricity generating arena? (2) What were the unique accomplishments of EPRI before the development of the Cooperative Agreement, which made developing the partnership with EPRI a highly cost-effective approach for USDOE? (3) What were the key accomplishments of the Cooperative Agreement in the development and execution of test and demonstration programs-accomplishments which significantly furthered the process of commercializing cofiring?
2001-09-01
British Library Electronic Table of Contents (United Kingdom)
Upconversion nanoparticles (UCNPs) with unique multi-photon excitation photoluminescence properties have recently been intensively explored as novel contrast agents for low-backgroundbiomedical imaging. In this work, we functionalize UCNPs with a polyethylene glycol (PEG) grafted amphiphilic polymer. The PEGylated UCNPs are loaded with a commonly used chemotherapy molecule, doxorubicin (DOX), by simple physical adsorption via a supramolecular chemistry approach for intracellular drug delivery. The loading and releasing of DOX from UCNPs are controlled by varying pH, with an increased drug dissociation rate in acidic environment, favorable for controlled drug release. Upconversion luminescence (UCL) imaging by a modified laser scanning confocal microscope reveals the time course of intracel...
2011-01-01
Dissociative electron attachment to CCl_4: Lifetime of the CCl_4"- intermediate
International Nuclear Information System (INIS)
Dissociative electron capture to CCl_4 is studied by measuring the angular and velocity distribution of Cl"- ions produced in collisions with velocity selected K(np) Rydberg atoms. Analysis of the data using a Monte Carlo collision code that models the detailed kinematics of the reaction indicates that the lifetime of the CCl_4"- intermediate formed by Rydberg electron capture is 7.5 #+-# 2.5 ps and that, upon dissociation, only a small fraction of the excess energy of reaction appears as translational energy of the Cl"- and CCl_3 fragments. The present approach is one of the few experimental techniques yet devised that can probe the lifetimes of collisionally-produced excited states on a picosecond timescale, and demonstrates that Rydberg atoms provide a unique tool with which to investigate the dynamics of dissociative electron attachment. Measurements are being extended to additional species, including CFCl_3.
1996-05-15
British Library Electronic Table of Contents (United Kingdom)
A novel PCR based assay was devised to specifically detect contamination of any Salmonella serovar in milk, fruit juice and ice-cream without pre-enrichment. This method utilizes primers against hilA gene which is conserved in all Salmonella serovars and absent from the close relatives of Salmonella. An optimized protocol, in terms time and money, is provided for the reduction of PCR contaminants from milk, ice-cream and juice through the use of routine laboratory chemicals. The simplicity, efficiency (time taken 3-4 h) and sensitivity (to about 5-10 CFU/ml) of this technique confers a unique advantage over other previously used time consuming detection techniques. This technique does not involve pre-enrichment of the samples or extensive sample processing, which was a pre-requisite in mos...
2012-01-01
British Library Electronic Table of Contents (United Kingdom)
Chitosan (a?-(1-4)-amino-2-deoxy-b?-D-glucan) is a deacetylated form of chitin, a polysaccharide from crustacean shells. Its unique characteristics, such as positive charge, biodegradability, biocompatibility, nontoxicity, and rigid structure, make this macromolecule ideal for an oral vaccine delivery system. We prepared reverse-phase evaporation vesicles (REVs) sandwiched by chitosan (Chi) and polyvinylic alcohol (PVA). However, in this method, there are still some problems to be circumvented related to protein stabilization. During the inverted micelle phase of protein nanoencapsulation, hydrophobic interfaces are expanded, leading to interfacial adsorption, followed by protein unfolding and aggregation. Here, spectroscopic and immunological techniques were used to ascertain the effects ...
2011-01-01
Diffusion examined by diffraction
X-ray diffraction offers a unique combination of advantages for kinetic study which include the non-destructive nature of the measurement, the use of bulk crystals, and the convenience of the experimental arrangements. These attributes and the availability of position-sensitive detectors and high-flux synchrotron radiation sources make this technique most useful for in situ, dynamical investigations. When using diffraction techniques to determine a diffusion coefficient, the principle of analysis entails a scattering theory and a kinetic model. The former allows the kinetic parameter(s) to be extracted from measured intensity, while the latter relates the kinetic parameter(s) to the diffusion coefficient(s). Three examples are demonstrated: (1) Palladium Silicide (Pd{sub 2}Si) Layer Growth on Silicon, (2) Decomposition of an Ni-12.5at%Si Superalloy, and (3) Short-range Ordering in Cu-Au Solid Solutions.
Design and optimization of thermoacoustic devices
International Nuclear Information System (INIS)
Thermoacoustics deals with the conversion of heat energy into sound energy and vice versa. It is a new and emerging technology which has a strong potential towards the development of sustainable and renewable energy systems by utilizing waste heat or solar energy. Although simple to fabricate, the designing of thermoacoustic devices is very challenging. In the present study, a comprehensive design and optimization algorithm is developed for designing thermoacoustic devices. The unique feature of the present algorithm is its ability to design thermoacoustically-driven thermoacoustic refrigerators that can serve as sustainable refrigeration systems. In addition, new features based on the energy balance are also included to design individual thermoacoustic engines and acoustically-driven thermoacoustic refrigerators. As a case study, a thermoacoustically-driven thermoacoustic refrigerator has been designed and optimized based on the developed algorithm. The results ...
2008-12-01
International Nuclear Information System (INIS)
A high-average power (kW) infrared (IR) free-electron laser (FEL) is currently being commissioned for the Jefferson Laboratory FEL User Facility. The IR FEL is driven by a unique superconducting rf linac which is recirculated to recover electron beam power that is not radiated in the FEL. The design and installation of the vacuum system for the FEL involved particular attention to minimizing particulate contamination which could cause problems with the superconducting acceleration cavities and the high power FEL optics. Particulate contamination levels of all vacuum components were monitored during the cleaning process using laser scattering. Cleaning, transport, and installation procedures were developed to minimize the contamination of the complete system. We will summarize a data base we compiled of particulate contamination levels of the various components installed in the FEL vacuum system.
1999-03-01
Energy Technology Data Exchange (ETDEWEB)
A strong effort is currently being devoted to the investigation of defects and diffusion phenomena in silicon. This effort is not only driven by the stringent technological requirements for the processing of integrated circuits of increased complexity and miniaturization, but also by the lack of fundamental understanding of many of the critical parameters and mechanisms involved. Experimental and theoretical investigations are needed to identify the properties of the defects, the mechanisms of impurity diffusion and the strength of impurity-defect, defect-defect, and impurity-impurity interactions. This volume provides a unique and interdisciplinary forum for the discussion of experimental, theoretical and applied aspects of defects and diffusion phenomena in silicon. Topics include: defect properties and diffusion phenomena in silicon; experimental and theoretical assessments of defect properties; transient-enhanced diffusion and dopant clustering; damage ...
1997-07-01
Crystal structure of the human centromeric nucleosome containing CENP-A
British Library Electronic Table of Contents (United Kingdom)
In eukaryotes, accurate chromosome segregation during mitosis and meiosis is coordinated by kinetochores, which are unique chromosomal sites for microtubule attachment. Centromeres specify the kinetochore formation sites on individual chromosomes, and are epigenetically marked by the assembly of nucleosomes containing the centromere-specific histone H3 variant, CENP-A. Although the underlying mechanism is unclear, centromere inheritance is probably dictated by the architecture of the centromeric nucleosome. Here we report the crystal structure of the human centromeric nucleosome containing CENP-A and its cognate ?-satellite DNA derivative (147 base pairs). In the human CENP-A nucleosome, the DNA is wrapped around the histone octamer, consisting of two each of histones H2A, H2B, H4 and CENP...
2011-01-01
Creating bulk nanocrystalline metal.
Energy Technology Data Exchange (ETDEWEB)
Nanocrystalline and nanostructured materials offer unique microstructure-dependent properties that are superior to coarse-grained materials. These materials have been shown to have very high hardness, strength, and wear resistance. However, most current methods of producing nanostructured materials in weapons-relevant materials create powdered metal that must be consolidated into bulk form to be useful. Conventional consolidation methods are not appropriate due to the need to maintain the nanocrystalline structure. This research investigated new ways of creating nanocrystalline material, new methods of consolidating nanocrystalline material, and an analysis of these different methods of creation and consolidation to evaluate their applicability to mesoscale weapons applications where part features are often under 100 {micro}m wide and the material's microstructure must be very small to give homogeneous properties across the feature.
2008-10-01
Cosmic time dilation: The clock paradox revisited
Energy Technology Data Exchange (ETDEWEB)
The relativistic time dilation is reviewed in a cosmological context. We show that a clock or twin paradox does not arise if cosmic time is properly taken into account. The receding galaxy background provides a unique frame of reference, and the proper times of geodesic as well as accelerated observers can be linked to the universal cosmic time parameter. This suggests to compare the proper time differentials of the respective observers by determining their state of motion in the galaxy grid. In this way, each observer can figure out whether his proper time is dilated or contracted relative to any other. In particular one can come to unambiguous conclusions on the aging of uniformly moving observers, without reference to asymmetries in measurement procedures or accelerations they may have undergone.
2004-05-01
Control of cooling during spray forming of bearing steel billets
Energy Technology Data Exchange (ETDEWEB)
In an effort to minimize the distortion of bearing steel rings during the production process, 100Cr6 steel billets are spray formed with a unique cooling control system to control the cooling and solidification behavior of the deposits. Effects of heating around the deposits, gas cooling at the substrate bottom and the gas flow over the deposits are investigated both by numerical simulation and experiment. Porosity profiles and microstructures of spray formed bearing steel are examined and evaluated. The investigation results show that the thermal boundary conditions of the deposits play important roles on the cooling and solidification behavior of the deposits, especially at the deposit periphery. Porosity in the 100Cr6 bearing steel deposit can be reduced significantly with the special cooling control system.
2004-10-10
Conservation laws. Generation of physical fields. Principles of field theories
In the paper the role of conservation laws in evolutionary processes, which proceed in material systems (in material media) and lead to generation of physical fields, is shown using skew-symmetric differential forms. In present paper the skew-symmetric differential forms on deforming (nondifferentiable) manifolds were used in addition to exterior forms, which have differentiable manifolds as a basis. Such skew-symmetric forms (which were named evolutionary ones since they possess evolutionary properties), as well as the closed exterior forms, describe the conservation laws. But in contrast to exterior forms, which describe conservation laws for physical fields, the evolutionary forms correspond to conservation laws for material systems. The evolutionary forms possess an unique peculiarity, namely, the closed exterior forms are obtained from these forms. It is just this that enables one to describe the process of generation of physical fields, to disclose connection ...
2007-01-01
Computer-mediated infertility support groups: An exploratory study of online experiences
British Library Electronic Table of Contents (United Kingdom)
Objective Over recent years the Internet has become an increasingly popular source of support and information for infertility, with a growing number of online support groups now available to individuals affected by fertility problems. The aims of the present study were therefore to explore the online experiences of individuals accessing infertility support groups via the Internet. Methods Ninety-five participants who were recruited from several online infertility support groups completed an online questionnaire containing a series of open-ended questions. Responses to the open-ended questions were analysed using inductive thematic analysis. Results The thematic analysis revealed five recurrent themes, which were labelled: `unique features of online social support', `improved relationship w...
2008-01-01
Comparison of constitutive models for plastic-bonded explosives
British Library Electronic Table of Contents (United Kingdom)
A constitutive model for an explosive consists of three parts: equation of state of reactants, equation of state of products, and reaction rate. In the absence of a good physical theory, models are empirical and based on heuristics. For the HMX based plastic-bonded explosive PBX 9501, three models have previously been calibrated and used in numerical simulations. Here, these three models are compared. They illustrate several generic difficulties with developing and validating models. The available data is insufficient to determine a constitutive model uniquely. Different models can be calibrated to fit the available data yet differ significantly in regions of phase space of importance to applications. Comparing models gives an indication of the uncertainty in model predictions outside the ...
2008-01-01
British Library Electronic Table of Contents (United Kingdom)
Abstract A 3-month, open-label, single-center study was conducted to determine whether a uniquely formulated and physiologically balanced topical treatment serum containing multiple growth factors, cytokines, peptides, antioxidants and depigmenting agents could improve the visible signs of facial photodamage. Thirty-seven females, aged 32-55 years, with mild to severe, fine and coarse peri-ocular wrinkles were enrolled and completed the study. Subjects applied the treatment serum to the face twice daily for 3 months in conjunction with a basic skincare regimen. Clinical evaluations of photodamage were performed at baseline and months 1, 2 and 3. Cutometer measurements and subject self-assessment questionnaires were also conducted during the study. Clinical evaluations showed statistically ...
2010-01-01
Chromosomal rearrangement segregating with adrenoleukodystrophy: A molecular analysis
Energy Technology Data Exchange (ETDEWEB)
The relationship between X chromosome-linked adrenoleukodystrophy and the red/green color pigment gene cluster on Xq28 was investigated in a large kindred. The DNA in a hemizygous male showed altered restriction fragment sizes compatible with at least a deletion extending from the 5[prime] end of the color pigment genes. Segregation analysis using a DNA probe within the color pigment gene cluster showed significant linkage with adrenoleukodystrophy (logarithm of odds score of 3.19 at [theta] = 0.0). These data demonstrate linkage, rather than association, between a unique molecular rearrangement in the color pigment gene cluster and adrenoleukodystrophy. The DNA changes in this region are thus likely to be helpful for determining the location and identity of the responsible gene. 33 refs., 4 figs.
1993-10-15
Application of mass spectrometry to fuels and materials testing at FFTF
International Nuclear Information System (INIS)
The Fast Flux Test Facility (FFTF) is a 400 MW(th) sodium cooled reactor and is the largest test reactor of its type in the world. It was designed and is being operated to serve two purposes: gaining liquid metal system experience and serving as a test bed for fuels and materials. During test operations it is possible that cladding breaches and escape of fission gas to the reactor cover gas region can occur. To identify the source of such a leak all 78 fuel pin assemblies contain ''gas tag'' with a unique ''tag'' mixture in each assembly. The mass spectrometric identification of tag isotope ratios makes possible rapid location and thus faster removal (if required) of breached test pins.
Application of activated charcoal radon collectors in high humidity environments
Energy Technology Data Exchange (ETDEWEB)
Most commercially based activated charcoal radon collectors were designed for use in indoor environments. However, at present, they are often used for research in radon surveys in unique environments, such as in the bathrooms, underground areas, mines, caves and tunnels. In these environments, the relative humidity would be around 100%, and a change in the sensitivity of cpm(Bq m{sup -3}){sup -1}(radon) would occur. For this study, the reduction in the sensitivity of activated charcoal radon collector due to environmental humidity was investigated, and the data correction was discussed. Here, ST-100 (Pico-Rad) was selected as an example of a familiar activated charcoal radon collector. According to our performance test, the humidity of 90% (20 deg. C) resulted in a 15% reduction of the sensitivity for 24 h collection. The ST-100 user should discuss the necessity of data correction by comparing the change of sensitivity with other levels of estimation errors.
2004-09-01
Analysis of in-situ fracture of oil sand formations by explosives
Energy Technology Data Exchange (ETDEWEB)
An analytical model is proposed for the design and simulation of in-situ fracture of deep oil sand formations. This model is based on the finite element variational principle in conjunction with special empirical modules to characterize in-situ oil sands behavior. A computer code by the name of SANFRAC was developed to handle the dynamic fracture of formations induced by explosives. Simulation of hydraulic fracture processes can be treated by the same code as special cases using the quasi-static analysis. Numerical case studies by the SANFRAC code indicate that extensive horizontal fracture can be achieved by dynamic loads with proper fracture starters configured at the injection well. The unique advantage of the dynamic fracturing technique over the hydraulic fracture methods is also demonstrated by these studies.
1987-03-01
An enhanced model framework of personalized material flow services
British Library Electronic Table of Contents (United Kingdom)
A growing concern about the consumer behavior in Internet economy has spurred the study of Material Flow, resulting in a unique type of consumer behavioral analysis. This research proposes an enhanced conceptual model for Personalized Material Flow Services for consumer behavior. In the era of Internet information technology, customer?s taste tends to be personalized for their market demand. It is observed that there are number of ?Long Tail? phenomena in several successful e-commerce business cases. However, the Long Tail phenomenon is an open question for our research in terms of its role in e-commerce marketing. In the proposed model-X-Party Personalized Material Flow Services, three elements are discussed. They are ?providing?, ?locating? and ?obtaining? based on X-Party Material Flow ...
2011-01-01
Algebraic approach to solve tt dilepton equations
International Nuclear Information System (INIS)
The set of nonlinear equations describing the standard model kinematics of the top quark antiquark production system in the dilepton decay channel has at most a fourfold ambiguity due to two not fully reconstructed neutrinos. Its most precise solution is of major importance for measurements of top quark properties like the top quark mass and tt spin correlations. Simple algebraic operations allow one to transform the nonlinear equations into a system of two polynomial equations with two unknowns. These two polynomials of multidegree eight can in turn be analytically reduced to one polynomial with one unknown by means of resultants. The obtained univariate polynomial is of degree 16. The number of its real solutions is determined analytically by means of Sturm's theorem, which is as well used to isolate each real solution into a unique pairwise disjoint interval. The solutions are polished by seeking the sign change of the polynomial in a given interval through ...
2005-11-01
Advanced power conversion based on the Aerocapacitor{trademark}
The authors report here, for the first time, high frequency testing of a new type of electrochemical double layer capacitor (EDLC), based on carbon aerogels: the Aerocapacitor. Carbon aerogels, are a novel type of carbon foam developed by Lawrence Livermore National Laboratory for military applications. The unique properties of carbon aerogels, high surface area (700 m{sup 2}/g), high density (1g/cc), well controlled pore diameter and high material conductivity (25 S/cm) made it an ideal EDLC electrode material. Using carbon aerogel as the electrode material, the authors have developed Aerocapacitors. These new EDLC`s have a frequency response comparable to that of aluminum electrolytic capacitors and are thus ideally suited to power conversion applications.
1997-10-01
A tribute to Oscar Buneman -- Pioneer of plasma simulation
Energy Technology Data Exchange (ETDEWEB)
Highlights are presented from among the many contributions made by Oscar Buneman to the science, engineering, and mathematics communities. Emphasis is placed not only on ''what'' this pioneer of computational plasma physics contributed but, of equal importance, on ''how'' he made his contributions. Therein lies the difference between technical competence and scientific greatness. The picture which emerges illustrates the open-mindedness, enthusiasm, intellectual/physical stamina, imagination, intellectual integrity, interdisciplinary curiosity, and deep humanity that made this individual unique. As a gentleman and a scholar, he had mastered the art of making cold technical facts ''come to life.'' Oscar Buneman died peacefully at his home near Stanford University on Sunday, January 24th, 1993. The profound influence he has had on many of his colleagues ...
1994-02-01
A survey of Chinese human resource management research in China
British Library Electronic Table of Contents (United Kingdom)
In this study, we examine research in the field of human resource management (HRM) published in six leading Chinese management journals from 2001 to 2007.First, we show publication patterns of Chinese HRM research by topic and reference discipline. Second, we assess the status of research quality using four raters to independently rate the articles based on type, orientation, design and statistical analyses. Through a systematic approach of analyzing this selection of articles, our study offers an opportunity for international scholars to appreciate the unique contributions of the Chinese language literature to the general HRM research. We conclude with a discussion of opportunities and directions for future research in this area to produce high quality indigenous research and build global...
2010-01-01
A novel approach to the dynamics of Szekeres dust models
We obtain an elegant and useful description of the dynamics of Szekeres dust models (in their full generality) by means of "quasi--local" scalar variables constructed by suitable integral distributions that can be interpreted as weighed proper volume averages of the local covariant scalars. In terms of these variables, the field equations and basic physical and geometric quantities are formally identical to their corresponding expressions in the spherically symmetric LTB dust models. Since we can map every Szekeres model to a unique LTB model, rigorous results valid for the latter models can be readily generalized to a non--spherical Szekeres geometry. The new variables lead naturally to an initial value formulation in which all scalars are expressed as scaling laws in terms of their values at an arbitrary initial space slice. These variables also yield a significant simplification of numerical work, since the fluid flow evolution equations become a system of ...
2011-01-01
One of the stiffest challenges in structural studies of proteins using NMR is the assignment of sidechain resonances. Typically, a panel of lengthy 3D experiments are acquired in order to establish connectivities and resolve ambiguities due to overlap. We demonstrate that these experiments can be replaced by a single 4D experiment that is time-efficient, yields excellent resolution, and captures unique carbon-proton connectivity information. The approach is made practical by the use of non-uniform sampling in the three indirect time dimensions and maximum entropy reconstruction of the corresponding 3D frequency spectrum. This 4D method will facilitate automated resonance assignment procedures and it should be particularly beneficial for increasing throughput in NMR-based structural genomics initiatives.
2010-05-01
A model of chemistry and thermal hydraulics in PWR fuel crud deposits
Energy Technology Data Exchange (ETDEWEB)
A model is described for simulating thermal hydraulic and chemical conditions within fuel crud deposits. Heat transfer takes place by wick boiling in which water flows through the porous deposit and evaporates into steam at the surface of chimneys. The transport and chemistry of dissolved species within the deposit is also modelled. This chemistry includes the equilibrium chemistry of Li/boric acid species, the equilibrium chemistry of Fe/Ni species and the radiolysis chemistry of water. The unique feature of this model is that the chemistry is coupled to the thermal hydraulics via the increase in the saturation temperature with the concentration of dissolved species. This has a profound effect on evaporative heat transfer within thick deposits, leading to conditions that explain the precipitation of LiBO{sub 2} and the possible formation of bonaccordite. The model helps understand several crud scrape observations, including why AOA is observed to occur for a crud ...
2006-07-01
A logarithmic time complexity algorithm for pattern searching using product-sum property
British Library Electronic Table of Contents (United Kingdom)
Product-sum property states that an ordered pair (s"n,p"n) is unique for any ordered set a"1,a"2,...,a"n where a"i,n@?N, and s"n and p"n are the sum and product of the elements of the set, respectively. This fact has been exploited to develop an O(log(M)) time complexity algorithm for pattern searching in a large dataset, where M is the number of records in the dataset. Two potential applications (from databases and computational biology) of this property have been demonstrated to show the effectiveness and working of the proposed algorithm. The space complexity of the algorithm rises to the quadratic order.
2011-01-01
1,3 Propanediol and its copolymers: Research, development and industrialization
British Library Electronic Table of Contents (United Kingdom)
Abstract 1,3 Propanediol (PDO), is now taking the transition from a traditional specialty chemical to a commodity chemical . The market for PDO is growing rapidly as the technology develops. With the advancing PDO production technology, polytrimethylene terephthalate (PTT) as a new type of polyester has been applied in carpet and textile fibers, monofilaments, films, and nonwoven fabrics, and in the engineering thermoplastics area, because PTT has unique properties compared to other polymers such as polyethylene terephthalate (PET) and polybutylene terephthalate (PBT). Responding to the environmental and sustainability factors, one or two step fermentation technology for PDO production has attracted people's attention. A novel flexible process for PDO production by using aerobic fermentati...
2010-01-01
(#alpha#+#beta#) - Sialon ceramic composites
International Nuclear Information System (INIS)
(#alpha#+#beta#)-SiALON ceramic composites are industrially important materials. Due to their unique chemistry, crystal structure and microstructural features, #alpha#-SiAlON has superior hardness while #beta#-SiALON offers high strength and toughness. The combination of the two phases enables materials engineers to design a ceramic where the physical properties of the composite can be tailored to a particular application. This article presents a general review of the crystal structures, fabrication and properties of the (#alpha#+#beta#)-SiALON composites with special highlights outlining how microstructural tailoring can control the properties of these advanced ceramic alloys. Copyright (1997) Institute of Metals and Materials Australasia Ltd.
Surface modification of PTFE sheet by synchrotron radiation in the soft X-ray region
International Nuclear Information System (INIS)
Full text: The surface properties of poly (tetrafluoroethylene) (PTFE) are changed by the exposure to synchrotron radiation (SR). We succeeded in controlling the wettability of the PTFE surface from hydrophobic to hydrophilic by varying the substrate temperature during the SR irradiation and found that the wettability was ascribable to microstructure and chemical composition of surface.In these previous works, oxygen atoms were found to inhabit on the hydrophobic surface of PTFE. In this study, we investigated the surface modification of PTFE from the SR exposure experiment under the O_2 gas atmosphere. The SR exposure to the PTFE sheet was carried out at beamline 6 (BL6) of the New- SUBARU. The PTFE sheet was irradiated to the white beam, ranging 50-1000 eV at BL6 at room temperature. The gas cell was mounted at the irradiation chamber. The O_2 gas pressure in the gas cell can be maintained at about 0.20 Pa during the SR exposure using 5mm #phi# hole window. The ...
2004-07-19
Relative correlation of Jet-REMPI monitoring with adsorption tube sampling followed by TDS-CIS-GC/MS
Energy Technology Data Exchange (ETDEWEB)
During earlier work rapid and highly sensitive Jet-REMPI (resonance-enhanced multiphoton ionization) mass spectrometry was applied for monitoring the effluent from thermal treatment of a filter dust during a de novo test under laboratory conditions. The sample, from ESP-Field 2 of an iron ore sintering plant, was already loaded with dioxins ({sigma}PCDD/F = 132 ng/g), their precursors (PCBz, PCPh) and other products of incomplete combustion. Heating filter dust in a temperature window 200-350 C under a flow of air results in further formation of these pollutants. As described elsewhere, on-line detection was mostly carried out using a non-selective ionization mode, to measure a wide range of compounds simultaneously. The changes of output suggest that the reaction products increase in chlorination level with time. Another explanation is that higherchlorinated compounds appear later as a consequence of lower volatility and stronger adsorption. However, due to mass ...
2004-09-15
Energy Technology Data Exchange (ETDEWEB)
This study investigated the effect of hydrogen content in producer gas on the performance and exhaust emissions of a supercharged producer gas-diesel dual-fuel engine. Two types of producer gases were used in this study, one with low hydrogen content (H{sub 2} = 13.7%) and the other with high hydrogen content (H{sub 2} = 20%). The engine was tested for use as a co-generation engine, so power output while maintaining a reasonable thermal efficiency was important. Experiments were carried out at a constant injection pressure and injection quantity for different fuel-air equivalence ratios and at various injection timings. The experimental strategy was to optimize the injection timing to maximize engine power at different fuel-air equivalence ratios without knocking and within the limit of the maximum cylinder pressure. Two-stage combustion was obtained; this is an indicator of maximum power output conditions and a precursor of knocking combustion. Better combustion, engine performance, ...
2009-09-15
Energy Technology Data Exchange (ETDEWEB)
Amorphous materials in the system xLi{sub 2}S{center_dot}(100-x)SiS{sub 2}, where x ranged from 50 to 70 mol %, and (100-y) (0.6Li{sub 2}S{center_dot}0.4SiS{sub 2}){center_dot}yLi{sub 4}SiO{sub 4}, where y ranged from 0 to 10 mol %, were synthesized by mechanical milling of crystalline starting materials, Li{sub 2}S, SiS{sub 2} and Li{sub 4}SiO{sub 4}. At the compositions with large amounts of Li{sup +} ions, a part of crystalline Li{sub 2}S used as a starting material remained in the milled powder samples. It was found that the milled powder samples in both systems obtained by mechanical milling exhibited high conductivities in the order of 10{sup -4}S{center_dot}cm{sup -1} at room temperature in spite of the presence of small amounts of Li{sub 2}S crystals. The conductivity values of the pelletized samples of xLi{sub 2}S{center_dot}(100-x)SiS{sub 2} powders maximized at the composition of about x=60. On the other hand, the conductivities in the composition range with y{<=}5 in ...
2000-02-01
Long pulse chemical laser. Final technical report
Energy Technology Data Exchange (ETDEWEB)
This report covers the technical effort through February, 1989. This effort was directed towards the technology associated with the development of a large scale, long pulse DF-CO{sub 2} chemical laser. Optics damage studies performed under Task 1 assessed damage thresholds for diamond-turned salt windows. Task 2 is a multi-faceted task involving the use of PHOCL-50 for laser gain measurements, LTI experiments, and detector testing by LANL personnel. To support these latter tests, PHOCL-50 was upgraded with Boeing funding to incorporate a full aperture outcoupler that increased its energy output by over a factor of 3, to a full kilojoule. The PHOCL-50 carbon block calorimeter was also recalibrated and compared with the LANL Scientech meter. Cloud clearing studies under Task 3 initially concentrated on delivering a Boeing built Cloud Simulation Facility to LANL, and currently involves design of a Cold Cloud Simulation Facility. A Boeing IRAD funded theoretical study ...
1989-02-01
Energy Technology Data Exchange (ETDEWEB)
'Improvement in understanding of the deposition of ambient dust particles on ECAM (Environmental Continuous Air Monitor) filters, reduction of the alpha-particle interference of radon progeny and other radioactive aerosols in different particle size ranges on filters, and development of ECAM''s with increased sensitivity under dusty outdoor conditions. As of May 1, 1998 (1/2 year into the project) the research-prototype 30-cm pulsed ionization chamber (PIC) is assembled and operational with an alpha particle energy resolution of better than 45 keV for 5-MeV alpha particles. Measurements of spectral resolution for alpha particles from radon decay products have been made as a function of filter type and dust loading conditions. So far, a study of ten filter types has found that the best combination of resolution and throughput is obtained with 3.0 \\265m Millipore fluoropore and 1.0 \\265m Corning FNMB filters. Experiments with gypsum and Portland cement dust ...
1998-06-01
Formation of metal oxides by cathodic arc deposition
Energy Technology Data Exchange (ETDEWEB)
Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window applications. Optical waveguide structures can be formed by refractive index variation using oxide multilayers. We have synthesized multilayers of Al{sub 2}O{sub 3}-Y{sub ...
1995-11-01
FABRICATION OF BISMUTH NANOWIRE DEVICES USING FOCUSED ION BEAM MILLING
International Nuclear Information System (INIS)
In this work, a focused ion beam (FIB) milling process has been developed to fabricate 50 nm Bi nanowire and transistor structures using FEI-200 dual beam FIB system. For the fabrication, 50 nm bismuth film was thermally evaporated through EBL patterned PMMA windows onto SiO_2 substrates with pre-defined contact pads. Bi nanowire widths ranging from 30 nm to 100 nm have been successfully fabricated by milling out unwanted areas using 30 KeV Ga+ ion beam. A single-pixel-line ion beam blanking technique has been utilised to fabricate Bi nanowire as small as 30 nm in diameter and few micrometers long. In order to form good ohmic contacts for sub 50 nm bismuth nanowires, a drill-and-fill process has been developed using FIB to sputter away the surface oxide of bismuth after the in-situ platinum nanowire contacts deposition. To our knowledge, this is the first time a focused ion beam process has been used to fabricate bismuth nanowire. The fabricated Bi nanowires were ...
2009-07-23
Experience from Arctic projects : meeting the challenges of Arctic and harsh environment projects
Energy Technology Data Exchange (ETDEWEB)
The main businesses of the Aker Group were outlined. The Aker Group has an operating revenue of 51.7 billion with operational experience in deepwater floaters, subsea infrastructure, onshore oil and gas plants, fixed offshore platforms, petrochemical refining, power generation, pulping, and mining. The company plans and executes capital projects, provides technology solutions and life-cycle operations, service and maintenance. The Aker Group owns 50 per cent of the Aker Kvaener offshore drilling rig located in the North Sea. This presentation outlined the challenges of working in a harsh environment. The area is characterized by a short productive season, low temperatures and limited sunlight. The direct environmental issues include spills and the impact of oil and gas infrastructure. Indirect issues include lowering the entry barriers for other kinds of resource exploitation. Other challenges of field development in Arctic areas include ice conditions, extreme temperatures, limited ...
2005-07-01
Developement of integrated evaluation system for severe accident management
International Nuclear Information System (INIS)
The scope of the project includes four activities such as construction of DB, development of data base management tool, development of severe accident analysis code system and FP studies. In the construction of DB, level-1,2 PSA results and plant damage states event trees were mainly used to select the following target initiators based on frequencies: LLOCA, MLOCA, SLOCA, station black out, LOOP, LOFW and SGTR. These scenarios occupy more than 95% of the total frequencies of the core damage sequences at KSNP. In the development of data base management tool, SARD 2.0 was developed under the PC microsoft windows environment using the visual basic 6.0 language. In the development of severe accident analysis code system, MIDAS 1.0 was developed with new features of FORTRAN-90 which makes it possible to allocate the storage dynamically and to use the user-defined data type, leading to an efficient memory treatment and an easy understanding. Also for user's convenience, ...
Deterministic calculations of radiation doses from brachytherapy seeds
International Nuclear Information System (INIS)
Brachytherapy is used for treating certain types of cancer by inserting radioactive sources into tumours. CDTN/CNEN is developing brachytherapy seeds to be used mainly in prostate cancer treatment. Dose calculations play a very significant role in the characterization of the developed seeds. The current state-of-the-art of computation dosimetry relies on Monte Carlo methods using, for instance, MCNP codes. However, deterministic calculations have some advantages, as, for example, short computer time to find solutions. This paper presents a software developed to calculate doses in a two-dimensional space surrounding the seed, using a deterministic algorithm. The analysed seeds consist of capsules similar to IMC6711 (OncoSeed), that are commercially available. The exposure rates and absorbed doses are computed using the Sievert integral and the Meisberger third order polynomial, respectively. The software also allows the isodose visualization at the surface plan. The user can choose ...
2003-08-17
Design of a closed 4 MW spallation target module with heat removal system for an ADS system
International Nuclear Information System (INIS)
At the Forschungszentrum Karlsruhe the HGF Strategy Fund project entitled 'Innovative Technology to Reduce Radiotoxicity' is performed which delivers an essential scientific contribution to the application oriented fundamental research for Accelerator Driven Systems (ADS). The addressed topics are in the areas of heavy liquid metal technology, thermalhydraulics and materials / corrosion. An ADS consists of three main components: an proton accelerator, a spallation target and a subcritical blanket. The strategic objective of an ADS is the transmutation of long-lived radioactive waste (plutonium, minor actinides and long-lived fission products) into short-lived isotopes or stable elements, thus closing the fuel cycle. The objective of one task of the HGF Strategy Fund Project is the numerical calculation of a closed spallation target module. In a consequent next step such a spallation target can be experimentally investigated at IKET and the numerical results can be validated. In this ...
Demonstrating leadership inside and out : green building project trains employees, educates clients
Energy Technology Data Exchange (ETDEWEB)
This article described a full-scale green renovation project undertaken by a construction management firm in Newton, Massachusetts. Chapman Construction and Design began renovating its own office building in late 2007 and completed it in September 2008. The firm set out to achieve LEED Platinum certification from the United States Green Building Council. The project involved energy saving modifications to its mechanical systems; replacing plumbing fixtures with high efficiency alternatives to reduce water consumption by at least 40 per cent; installing skylights and additional windows to allow more natural light into the interior space; salvaging doors, lighting, metal studs and masonry whenever possible; and using sustainable products such as recyclable carpets, tiles and low-VOC paint. The main feature of the renovation was a new 47 kW (DC) photovoltaic (PV) solar power array installed on the rooftop. The PV array includes 208 panels and a SunPower SPR-225 system ...
2009-01-15
Energy Technology Data Exchange (ETDEWEB)
A solid electrolyte for lithium batteries requires several properties: a good ionic conductivity of about 10{sup -3} S/cm at 298 deg. K, a high cationic transport number (greater than 0.5), a redox stability window higher than 4.5 V, a good stability of the interface with the lithium electrode, and a sufficient mechanical stability. The family of gelled or hybrid electrolytes seems to meet all these requirements. Thus, a systematic study of the gelling of an ethylene carbonate and lithium bistrifluorosulfonimide (LiTFSI) based electrolyte has been carried out. The polymers used for gel or pseudo-gel synthesis are POE, PMMA and PAN which represent 3 different cases of interaction with the electrolyte. All the properties mentioned above have been studied according to the nature of the polymer and to the concentration of lithium salt, showing the advantages and drawbacks of each polymer. The possibility of using some of these gels in lithium-ion batteries has been ...
1996-12-31
Calibration of cylindrical detectors using a simplified theoretical approach
Energy Technology Data Exchange (ETDEWEB)
The calibration of cylindrical detectors using different types of radioactive sources is a matter of routine. The most accurate method, that of experiment, is limited by several factors when the energy interval is broad, requiring a relatively large number of primary standards, implying considerable investment of money and time. Several other techniques can be used instead, including Monte Carlo simulations and semi-empirical methods. Calculations based on the first technique require good definition of the geometry and materials, including the dead layer and window thickness together with an accurate set of cross-sections. The second technique requires two different types of experimental input, the first being from use of sources emitting cascade {gamma} rays and the second from use of sources emitting isolated {gamma} rays in order to cover the wide energy range and provide coincidence-summing corrections, respectively. Here, we introduce a new theoretical ...
2006-09-15
Brain SPECT of chronic fatigue syndrome (CFS): SPM analysis of two age groups
International Nuclear Information System (INIS)
Full text: Chronic fatigue syndrome (CFS) is a complex disorder characterised by profound fatigue and neuropsychiatric dysfunction. Previous studies with cerebral perfusion SPECT (rCBF) scans were performed with inhomogeneous patient populations and were not analysed with Statistical Parametric Mapping (SPM). We have used SPM to study subjects with moderate CFS based on the Fukuda criteria, who were not on medication and not depressed, compared to age matched control subjects. An apparent bimodal age distribution has been observed in CFS. Subjects were therefore divided into two age groups: 16-35 or under 35 (17 CFS, 11 control) and 36-61 or over 35 (15 CFS, 15 control). HMPAO brain SPECT was acquired on a 3-head camera. After lower window scatter subtraction, reconstruction with attenuation correction (mu=0.15/cm) and editing of facial activity, scans were spatially normalised (affine + 2x3x2 nonlinear) to SPM's anatomical space. SPM statistical analysis yielded ...
2002-05-04
Energy Technology Data Exchange (ETDEWEB)
A 16 l liquid parahydrogen target has been developed for a measurement of the parity-violating {gamma}-asymmetry in the capture of polarized cold neutrons on protons in the {rvec n} + p {yields} d + {gamma} reaction by the NPDGamma collaboration. The target system was carefully designed to meet the stringent requirements on systematic effects for the experiment and also to satisfy hydrogen safety requirements. The target was designed to preserve the neutron polarization during neutron scattering on liquid hydrogen (LH{sub 2}), optimize the statistical sensitivity to the {rvec n} + p {yields} d + {gamma} reaction, minimize backgrounds coming from neutron interaction with the beam windows of the target cryostat, minimize LH{sub 2} density fluctuations which can introduce extra noise in the gamma asymmetry signal, and control systematic effects. The target incorporates two mechanical refrigerators, two ortho-para convertors, an aluminum cryostat, an aluminum target ...
2010-05-01
Website Policies and Important Links Comments
WorldWideScience.org is maintained by the U.S. Department of Energy's
Office of Scientific and Technical Information as the Operating Agent
for the WorldWideScience Alliance.
