Energy Technology Data Exchange (ETDEWEB)

The following paragraphs summarize the progress of each research project funded under the WVU Cooperative Agreement during the third quarter of 1997 (July - September 1997). The projects are arranged according to their 1997 WVU task number. WVU Focus Area 1.0: Subsurface Contaminants, Containment and Remediation Task No. 1.1: Project discontinued. Task No. 1.2: Development of Standard Test Protocols and Barrier Design Models for Desiccation Barriers (K. Amininan & S. Ameri): A number of experiments were preformed this period to evaluate the ability of the dried sand-packs to act as a barrier to liquids. Water infiltration tests were done with a constant head, dispersing 80 ml of water, and by adding water in small increments. Results indicate that when the water is spilled over the sand-pack, it has the tendency to channel through the sand-pack, significantly reducing the capacity of the dried zone to retain liquid ...

CERN Document Server

Turbulence in the positive column of a glow discharge

KoreaScience (Korea)

Full Text Available

UK PubMed Central (United Kingdom)

Quartz has a dissipation factor of approximately 10(-4), which is an order of magnitude less than that of the best glasses previously used to fabricate patch pipettes; it's dielectric constant of 3.8...Full Text Available

CERN Document Server

Quartz fiber calorimetry is a technique the signal generation mechanism of which is based on the Cherenkov effect. In this article we try to give a comprehensive overview of the subject. We start with a general introduction to calorimetry where the basic elements that characterize the development of electromagnetic and hadronic showers are discussed. Then we describe in detail the operation principle and the properties of calorimeters equipped with quartz fibers. The main advantages of this type of calorimeters are the radiation hardness, the fast response and the compact detector dimensions, features that derive from the quartz material and the specific mechanism of operation. A section is devoted to presenting the quartz fiber calorimeters that have been built or planned to in various experiments to operate as centrality detectors, trigger detectors, luminosity monitors or general purpose very forward ...

Energy Technology Data Exchange (ETDEWEB)

A Norwegian Research Program on Improved Oil Recovery (IOR) in North Sea reservoirs was launched in 1992. Microbial methods, applied in this context, is a part of this program. The scope, the methodological approach, and results from the three first years are presented. Water profile control, using biomass to block high permeable zones of a reservoir, has been investigated using nitrate-reducing bacteria in the injected sea water as plugging agents. Emphasis has been put on developing a process that does not have disadvantages secondary to the process itself, such as souring and impairment of the overall injectivity of the field. Data from continuous culture studies indicate that souring may successfully be mitigated by adding nitrite to the injected seawater. The morphology and size of generic-nitrate-reducing seawater bacteria have been investigated. Screening of growth-promoting nutrients has been carried out, and some sources were detected as favorable. Transport and penetration of ...

Science.gov (United States)

Not Available

Norwegian Open Research Archives (NORA)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Emission spectra obtained for three irradiated granular quartz samples under 1.43 eV excitation exhibited the 2.2 and 3.1 eV emission bands characteristic of feldspars. Excitation spectra of these same samples and several others show the 1.44 eV resonance typical of feldspars. This provides convincing evidence that the 2.2 and 3.1 eV infrared stimulated luminescence observed in these granular quartz samples arises from feldspar inclusions.

British Library Electronic Table of Contents (United Kingdom)

An energy transfer and conversion model for high-temperature solar cavity receivers has been developed using the transport behaviour of solar radiation as described by the spectral radiative exchange factors. A Monte-Carlo ray-tracing method coupled with optical properties was adopted, to predict radiation characteristics of the solar collector system by calculating radiative exchange factors. A cavity receiver with a plano-convexo quartz window was proposed, based upon the directional characteristics of the focal flux and the redistribution effect of the quartz window. Parametric studies on the windowed receiver provided a more uniform flux distribution, higher efficiency and lower loss than the windowless receivers. The predicted results serve as a design reference for the solar receiver...

KoreaScience (Korea)

Full Text Available

Norwegian Open Research Archives (NORA)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A method is proposed for the quantitative high-temperature isolation of /sup 111/In from silver irradiated by ..cap alpha..-particles into a gas phase containing a mixture of HCl and H/sub 2/O with a total pressure of about 3 Pa for these gases. It is shown that the indium evolved into the gas phase probably occurs in the form of at least three compounds, viz.., the trichloride, monochloride, and oxychloride, which have adsorption temperatures on quartz of around 385, 475, and 655 K, respectively. All these compounds are readily washed from the surface of quartz apparatus by a weak (0.05 M) solution of hydrochloric acid.

Energy Technology Data Exchange (ETDEWEB)

The behavior of melter feed (a mixture of nuclear waste and glass-forming additives) during waste-glass processing has a significant impact on the rate of the vitrification process. We studied the effects of silica particle size and sucrose addition on the volumetric expansion (foaming) of a high-alumina feed and the rate of dissolution of silica particles in feed samples heated at 5 C/min up to 1200 C. The initial size of quartz particles in feed ranged from 5 to 195 {micro}m. The fraction of the sucrose added ranged from 0 to 0.20 g per g glass. Extensive foaming occurred only in feeds with 5-{micro}m quartz particles; particles {ge}150 {micro}m formed clusters. Particles of 5 {micro}m completely dissolved by 900 C whereas particles {ge}150 {micro}m did not fully dissolve even when the temperature reached 1200 C. Sucrose addition had virtually zero impact on both foaming and the dissolution of silica particles. Over 100 sites in the United ...

Science.gov (United States)

... surprise. During Operation Goodwood, the British attempt to break out of their bridgeheads in Normandy, aBritish column was ...

Science.gov (United States)

... 2-22 Page 31. The mercury barometer operates on the principle of air pressure forcing the mercury column up an evacuated tube. ...

CERN Document Server

A simple analytical model of the barrier discharge in a long gap between opposing plane electrodes is developed. It is shown that the plasma density becomes uniform over large part of the gap in the course of the discharge development, so that one can speak of a formation of a dynamic positive column. The column completely controls the dynamics of the barrier discharge and determines such characteristics as the discharge current, discharge duration, light output, etc. Using the proposed model, all discharge parameters can be easily evaluated

British Library Electronic Table of Contents (United Kingdom)

An effective rehabilitation strategy is proposed to enhance the strength and stiffness of the beam-column joint in this study. An analytical model is proposed to predict the column shear of the joints strengthened with carbon fiber reinforced polymer (CFRP). Three full scale interior beam-column joints, including two specimens strengthened with CFRP and one prototype specimen, are tested in this study. The specimens are designed to represent the pre-seismic code design construction in which there is no transverse reinforcement. A new optical non-contact technique, digital image correlation (DIC), which can measure the full strain field of specimen, is used to measure and observe the full strain field of the joint. The experimental results show that the beam-column joints strengthened with ...

International Nuclear Information System (INIS)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 #mu#m; drops of diameter size 1.5 #mu#m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols from ...

International Nuclear Information System (INIS)

The principal types of uranium deposits in Ontario are carbonatites and fenites, alkalic volcanic rocks, pegiatites, calc-silicate rocks, pyritic quartz-pebble conglomerates, polymictic conglomerates and some pelitic rocks, and various 'pitchblende' deposits including late Precambrian unconformities, possibly late Precambrian diabase dikes, and other unconformities: carbonates, sandstones, lignites, and semi-pelitic rocks of middle and upper Precambrian age. Only red unzoned pegmatite and the pyritic quartz-pebble conglomerate have supported production. Ontario reasonably assured and estimated resources in the economic and subeconomic categories in 1977 amounted to 553 000 tonnes U, and 1977 production was 4000 tonnes U. Measured, indicated, and inferred resources in the Elliot Lake - Agnew Lake area are at least 400 000 tonnes U. The latter deposits are also a significant thorium resource. Geological features reflecting major changes in ...

Energy Technology Data Exchange (ETDEWEB)

The testing performed during the last phase of the geothermal direct contact heat exchanger program utilizing the 500 kW pilot plant provided more insight into the capabilities and limits of the direct contact approach and showed that more work needs to be done to understand the inner workings of a large direct contact heat exchanger if they are to be modeled analytically. Testing of the column demonstrated that the performance was excellent and that the sizing criteria is conservative. The system operated smoothly and was readily controlled over a wide range of operating conditions. Performance evaluation showed pinch differentials of 4/sup 0/F or less and better than predicted heat transfer capability. Testing during this final phase was directed towards establishing the limits of the column to transfer heat. The working column height was shortened progressively to approximately 16 feet from a design length of 28 feet. ...

Energy Technology Data Exchange (ETDEWEB)

Mineral matter in coals is important in various senses for coal liquefaction. It is possible that the catalytic activity is affected by the interaction between catalyst and mineral matter. Iron-based catalyst forms pyrrhotite in the process of liquefaction, but the interaction between it and mineral matter is not known in detail. In this study, the interaction between mineral matter and catalyst and the selective reaction between them were investigated. Tanito Harum coal was used for this study. This coal contains a slight amount of siderite and jarosite besides pyrite as iron compounds. Liquefaction samples were obtained from the 1 t/d NEDOL process PSU. The solid deposits in the reactor mainly contained pyrrhotite and quartz. A slight amount of kaolinite was observed, and pyrite was little remained. It was found that the catalyst (pyrrhotite) often coexisted with quartz, clay and calcite. 8 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

Focused ion beam (FIB) repair of chromium defects on photomasks and reticles leaves a post repair stain in the quartz substrate. The wavelength dependent absorption properties of typical stained regions have been measured, showing transition losses up to 80% in the deep uv. A simple model is in good qualitative agreement with the experimental results. (author).

Energy Technology Data Exchange (ETDEWEB)

Experimental data on the gas holdup and the mean bubble size in a bubble column with a single nozzle was obtained for gas-molten salt systems of a eutectic mixture of LiCl (58 mol %)-KCl (42 mol %) and molten NaNO/sub 3/. The liquid-phase mass transfer coefficient K /SUB L/ was evaluated from the specific surface area a and the volumetric coefficient K /SUB L/ a data for oxygen and carbon dioxide absorption into molten NaNO/sub 3/. The dimensionless correlations of the performance of bubble columns for aqueous solutions can be extended to the gas-molten salt systems.

Science.gov (United States)

the southern Arabian Gulf region left its signature on the heterogeneous aerosol .... Arabian Gulf region, since large differences in ? may be caused by ...

Science.gov (United States)

By Charles E. Watkins. 2458. An Instrument Employing a Coronal Discharge for ..... Grover, W. S. Hyler, and L. R. Jackson. 2640. Interaction of Column and ...

Energy Technology Data Exchange (ETDEWEB)

A distillation column with an adjustable slope horizontal rectification section was constructed. A rotating screw brush was inserted into the section, which could be rotated from 0 to 600 rpm with an external motor. Distillation experiments were carried out using the system cyclohexane-heptane at total reflux at slopes of 0(horizontal), 5 and 10 degrees. Separation efficiency for the horizontal column was the highest of the three orientations, and was obtained as HETP from 0.04 to 0.16 m at F-factor of 0.05 to 0.4 m/s(kg/m{sup 3}){sup 1/2} in the range of 100 to 600 rpm. The HETP for each slope was roughly constant at a rotation speed of more than 300 rpm. The values of the pressure drop were found to be equivalent to those of one seventh to one fifth of conventional packed columns. (author)

British Library Electronic Table of Contents (United Kingdom)

Steel building frames are often analyzed for stability in an elastic way, while most of their columns behave inelastically at the buckling stage. Most column design provisions allow for inelastic behavior, but overall inelastic stability analysis is rarely performed. In this study the analysis philosophy is centered on the overall frame stability and its true safety factor. As many columns show inelastic behavior at the buckling stage, the proposed procedure takes due consideration of this fact. Once the overall buckling factor for the frame is obtained, individual column effective length factors, and their true slenderness ratios are computed, and used in the design relationships. This procedure circumvents the use of design nomographs and numerous formulas proposed in the past to allevia...

Energy Technology Data Exchange (ETDEWEB)

Using the example of perhydrophenanthrene, perhydroanthracene and cyclopentanodecalin isomers a possibility is shown to use packed capillary columns containing graphitized thermal carbon black for a complete separation of high-boiling mixtures of polycyclic saturated hydrocarbon isomers in accordance with the geometric structure of their molecules.

International Nuclear Information System (INIS)

Following a recent refurbishment of the NPL Thermal Neutron Facility, the spectrum of the epithermal and fast neutron component of the beam produced by the thermal column of this facility was measured over the energy range from thermal to 20 MeV using a Bonner sphere spectrometry system. The effect of the presence of epithermal and fast neutrons on the measured response of commonly-used thermal neutron dosemeters was calculated. (author)

Energy Technology Data Exchange (ETDEWEB)

The purpose of this research was to investigate the de-entrainment of boron for evaporators used in nuclear power plants. The forced circulation and semi-continuous type evaporator was used in the experiment. Cyclone and glass-wool packed column which is supposed to provide good decontamination factor as well as easy maintenance, were selected as de-entrainment device to be used in the evaporation of radioactive liquid wastes. The de-entrainment device combined with cyclone and glass-wool column has shown overall DF more than 1000 for boron.

Energy Technology Data Exchange (ETDEWEB)

In order to judge the potential fluorescent lamp applications of various low-pressure positive column discharges it is necessary to measure the absolute power emitted in the ultraviolet region of the spectrum. For rare-gas discharges the principle emission occurs in the vacuum ultraviolet so that it is difficult to measure the radiant emittance (power per unit area) of the resonance radiation by standard methods. Two independent techniques are discussed for measuring the radiant emittance of positive column discharges in the vacuum ultraviolet. These techniques are used to study xenon positive column discharges at the resonance wavelength of 147 nm. The first method relies on the measurement of the resonance level density by absorption techniques. The effective decay rate of the resonance level is then determined by the simulation of resonance radiation transport. These two quantities are combined to yield the radiant ...

International Nuclear Information System (INIS)

The "6"2Zn-"6"2Cu generator system is one of the few which yield a pure positron emitting daughter. The authors have developed a method for the preparation of this generator system following 32 MeV #alpha# particle bombardment of nickel targets. The chemical processing involves two stages: first a hydrous zirconium oxide column is used at pH 4-5 to separate the zinc and copper activities produced in the target nickel, and secondly, a conventional anion exchange column is used to retain the "6"2Zn and remove all copper activities in 2M HCl. This column serves as the "6"2Cu generator which will yield pure "6"2Cu repeatedly, free from "6"2Zn and other impurities, in a mixture of HCl and NaCl. A method is outlined also to obtain a solution of "6"2Zn using the hydrous zirconium oxide (HZO) column. "6"1Cu can be prepared as a by-product in the above procedure, but a method for the preparation of "6"1Cu alone ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, an amount of confining reinforcement required for the sufficient flexural ductility of reinforced concrete column was investigated. An equation to calculate the required confining reinforcement ratio was deduced from the analytical investigation and examination on the previous experimental data as to the effects of various factors on the required confining reinforcement ratio. The rotation angle required in plastic hinges, the axial force ratio, the material properties such as concrete strength, and the ratio of core area to the whole area of column sections were employed as the factors. From the examination of the equation, it was shown that the ultimate rotation in plastic hinges calculated by the equation was more conservative than the ultimate rotaion angle of members obtained by test column specimens. It was also indicated that the ultimate rotation angle of members of columns failed ...

British Library Electronic Table of Contents (United Kingdom)

In this study two surface sensitive methods, i.e. quartz crystal microbalance with dissipation monitoring (QCM-D) and ellipsometry, were used for erosion measurements of a rosin-based marine antifouling paint binder. Thin films of the binder were applied on sensor surfaces by the means of spin-coating and the effect of water velocity over the paint film, water temperature or ionic strength on erosion was investigated. Both the acoustic QCM-D model and the optical ellipsometry model gave comparable erosion results. The initial 2-50nm rapid erosion of the top layer was followed by steady-state erosion rate until end of experiment. For example, the steady-state erosion rate was 12nm/24h in artificial seawater at 23degreeC and with a flow of 200ml/min over the paint surface as measured with QC...

International Nuclear Information System (INIS)

Magnetic materials such as yttrium iron garnet (YIG) are of great importance for its magneto-optic properties and for their potential applications in the domain of optical telecommunications. The deposition of thin films of YIG, on quartz or GGG (gadolinium gallium garnet) substrate, was performed using radio frequency non reactive magnetron sputtering, followed by high temperature annealing which is needed to enhance the crystallinity of the layers. Rutherford backscattering spectrometry RBS was used to determine the thickness and stoichiometry of the performed layers in order to investigate correlations between growth conditions and the quality of the final material. RBS measurements showed the influence of the deposition time and the temperature substrate on the film growth and its stoichiometry. (author)

Energy Technology Data Exchange (ETDEWEB)

Objective of the project is characterization of electrode reactions in molten salt by using metal oxides and silica-based electrode. The scope of project are characterization of metal oxide properties in molten salt and miniaturization of 3-electrode electrochemical test cell. Electrochemical micro-cell for actinide-LiCl-KCl molten salt was newly designed. Electroless and electrochemical deposition technique was applied to Mo coating on quartz tube. From the design of electrode and 3-electrode electrochemical cell suitable for the tests in molten salt electrolyte, so it is anticipated to get the information on the electrochemical behavior of metallic electrode in molten salt and to secure the information on oxidation/reduction behavior of actinide

Energy Technology Data Exchange (ETDEWEB)

We propose that a search for extra-terrestrial life can be approached as a Search for Extra-Terrestrial Homochirality{emdash}SETH. Homochirality is probably a pre-condition for life, so a chiral influence may be required to get life started. We explain how the weak force mediated by the {ital Z}{sup 0} boson gives rise to a small parity-violating energy difference (PVED) between enantiomers, and discuss how the resulting small excess of the more stable enantiomer may be amplified to homochirality. Titan and comets are good places to test for emerging pre-biotic homochirality, while on Mars there may be traces of homochirality as a relic of extinct life. Our calculations of the PVED show that the natural L-amino acids are indeed more stable than their enantiomers, as are several key D-sugars and right-hand helical DNA. Thiosubstituted DNA analogues show particularly large PVEDs. L-quartz is also more stable than D-quartz, and we believe that ...

International Nuclear Information System (INIS)

A method, based on anion exchange chromatography, is presented for the isolation of "1"3"9Ce after production by a proton-induced nuclear reaction on a thick praseodymium target. After bombardment the target is dissolved in nitric acid and "1"3"9Ce oxidised to the Ce(IV) oxidation state with bromic acid. "1"3"9Ce is then separated form the praseodymium by anion exchange chromatography on a Ag MP-1 resin column in a nitric acid - bromic acid mixture. "1"3"9Ce is sorbed onto the resin column and praseodymium eluted with the acid mixture. The bromic acid is washed out of the column with nitric acid and "1"3"9Ce finally eluted with dilute nitric acid containing sulphur dioxide.

British Library Electronic Table of Contents (United Kingdom)

The paper discusses the aspects of repair and retrofitting technique adopted for a damaged reinforced concrete beam-column joint specimen under cyclic loading. A specimen designed based on Indian Standard specifications with consideration of seismic load but without adopting ductile detailing (NonDuctile) was investigated under reverse cyclic loading. Then, the damaged nonductile specimen was repaired with epoxy mortar and grouted using low viscous polymer, and retrofitted using fiber reinforced plastic (FRP) wrapping in beam and column components and steel plate jacketing in joint region. The experimental results showed that the retrofitted specimen not only regained its original strength and stiffness but also has overcome the deficiencies of nonductile detailing. The present study shows...

British Library Electronic Table of Contents (United Kingdom)

We have studied the nature of continuum emitted in the visible spectral range from a noncontracted positive column of discharge in a cesium vapor-xenon mixture at a pressure of 45 Torr and at a degree of ionization below 3 ? 10?6. The main contribution to the continuous emission under such conditions is due to electron-xenon atom bremsstrahlung. The intensity of emission has been experimentally and theoretically studied as a function of the electric field strength and electron density in the positive column. It is established that an increase in the visible emission intensity with the electric field strength is related to an increase in the number of hot electrons in plasma.

British Library Electronic Table of Contents (United Kingdom)

Glass fiber-reinforced polymer (GFRP) reinforcing bars were used recently as main reinforcement for concrete structures. The noncorrodible GFRP material exhibits linear-elastic stress-strain characteristics up to failure with relatively low modulus of elasticity compared to steel. This raises concerns on GFRP performance in structures where energy dissipation, through plastic behavior, is required. The objective of this research project is to assess the seismic behavior of concrete beam-column joints reinforced with GFRP bars and stirrups. Two full-scale exterior T-shaped beam-column joint prototypes are constructed and tested under simulated seismic load conditions. One prototype is totally reinforced with GFRP bars and stirrups, while the other one is reinforced with steel. The experimen...

British Library Electronic Table of Contents (United Kingdom)

Abstract Remediation of ground water containing anionic contaminants presents a great challenge. Because of its low cost, surfactant-modified zeolite (SMZ) has been studied for >10 years for potential uses as permeable barrier materials to remove anionic contaminants from water. In this study, zeolite aggregates with particle size of 3.4 to 4.8 mm were modified by hexadecyltrimethylammonium (HDTMA) bromide, a cationic surfactant, to a surfactant loading level of 80 mmol/kg and a concurrent counterion bromide loading level of 34 mmol/kg. While no retardation of chromate transport was observed for unmodified columns, a retardation factor of 60 was found for chromate transport through the SMZ columns. Slow but persistent desorption of HDTMA occurred throughout the chromate transport experimen...

Energy Technology Data Exchange (ETDEWEB)

Theoretical assessment on the chromatographic {sup 99m}Tc generator preparation using (n, {gamma}) {sup 99}Mo produced ex-natural molybdenum was carried out. The relationship between the neutron flux for MoO{sub 3} target activation, Mo-content or Mo adsorption capacity of column packing material, {sup 99m}Tc pertechnetate concentration and/or {sup 99m}Tc radioactivity of eluate was established. The reasonably lower limit of neutron flux of reactor and Molybdenum content of column packing material were found out to estimate the production of portable chromatographic generators available for nuclear medicine application. The concentration of {sup 99m}Tc pertechnetate eluate of low {sup 99m}Tc concentration using the column elution technique was also evaluate theoretically and conducted successfully in practice. Three options of {sup 99m}Tc generator using Titanium-Molybdate, Zirconium-Molybdate and Zirconium Oxide as ...

Energy Technology Data Exchange (ETDEWEB)

The development and evaluation of a post-column reaction detector sensitive to platinum(II) complexes is presented in which sodium bisulfite is used as the derivatizing agent with potassium dichromate as an activating agent. The influences of mobile phase changes (i.e., pH, organic modifiers, electrolytes), oxygen, metal ions, and order of reagent addition on reaction kinetics and product yield are defined and used in optimization of detector response. Detection at lambda/sub max/ 290 nm results in an on-line post-column sensitivity of 40-60 ng/mL for selected cis-dichloroplatinum complexes and a sensitivity of 300-1200 ng/mL for four (substituted)-malonato-platinum complexes. The reaction detector is used to monitor the kinetics of aquation of cisplatin (CDDP) and to quantitate CDDP degradation in plasma. As the sensitivity for CDDP in plasma is comparable to that achieved from high pressure liquid chromatography (HPLC) effluent ...

Energy Technology Data Exchange (ETDEWEB)

This paper deals with electron flux densities and electron energy flux densities in positive column discharges. Recent kinetic calculations by Uhrlandt and Winkler have revealed the interesting physical phenomenon of radially inward directed energy flux densities in positive column plasmas. We have used a self-consistent positive column model, based on an accurate and highly detailed Monte Carlo code, to study this effect in more depth. The results of this study show a rather complex physical picture of electron particle and energy flux densities. Electrons with low energies usually exhibit radially outward directed particle and energy flux densities. At energies above the threshold for electronic excitation particle and energy flux densities are usually inward directed. Only close to the wall, at total energies above the wall potential energy, do these flux densities point towards the wall. The thickness of this ...

UK PubMed Central (United Kingdom)

The aim of the present study was to describe the physicochemical characteristics of streptococcal T antigen. T protein isolated from Streptococcus pyogenes type 12 (R53/1077, Colindale) and purified...Full Text Available

UK PubMed Central (United Kingdom)

The purpose of the work was to quantitatively characterize temperature effects on the bacterial leaching of sulfide ore material containing several sulfide minerals. The leaching was tested at eight...Full Text Available

UK PubMed Central (United Kingdom)

An anion-exchange column technique for extraction of antibiotics from serum proteins has been developed for use in the assay of cephapirin, cefotaxime, and cefoxitin by high-pressure liquid chromatography....Full Text Available

International Nuclear Information System (INIS)

The mixed structure of a nuclear reactor building is composed of SC-columns, S-beams, S-joints and PCa-panels. Following the last report (Part 7)[1], the main test results of the mixed structure, that is, the deformation mode, strain distribution and shear strength, are described. The S-joints using ultrahigh strength materials had no buckling nor shear slipping. The proposed mixed structure resisted the external horizontal forces under integrated uniformity among SC-columns, S-joints and PCa-panels. It could be confirmed that the mixed structure can be established. (author)

International Nuclear Information System (INIS)

During a high temperature treatment of the radioactive wastes that contain ruthenium, some ruthenium is volatilized and released to the off gas system. The volatilized ruthenium is removed with a scrubber and an adsorber. It was expected that the scrubber was one of the most effective equipments to remove ruthenium and the decontamination factor of the scrubber was studied. The experimental apparatus was simulated as part of an actual perforated plate column scrubber. The non-radioactive ruthenium which simulated the radioactive ruthenium was volatilized and fed into the scrubber. The decontamination factor of the scrubber was determined by the ratio of the ruthenium concentration at the inlet and outlet of the scrubber off gas stream. The results showed that the scrubber removed the volatile ruthenium effectively as expected.

International Nuclear Information System (INIS)

Optimal neutron energy for boron neutron capture therapy (BNCT) has been studied. Epithermal neutron is superior to thermal neutrons in treating deep-seated tumors. Design of the epithermal neutron column for BNCT has been performed by using a two-dimensional transport calculation code. Aluminum and heavy water are used as moderation materials. A thermal neutron column is also designed using heavy water as thermalization material. The configuration of the facility for treatment and research of BNCT and also for basic radio-biological studies of neutrons has been presented. (author).

International Nuclear Information System (INIS)

Addition of Gadolinium Nitrate as chemical shim to moderator heavy water of 540 MWe PHWR, at 15 mg/kg level (at a pH of 5.0) is practiced for reactor shutdown purposes. Presently a strong acid cation exchanger column is used for this purpose. During this operation, the moderator pH of 3.8, with the IX column outlet pH of ?3.5-3.6 was observed against the technical specification demand that when Gd is present, the pH of moderator must be in the range of 5.0-5.5. In order to achieve an iso-pH regime during Gd removal, studies were conducted using a mixed bed of strong acid cation resin plus a weak base anion resin (loaded in the volume ratio of 1 : 6), backed up in the same column (bottom most layer) by a 5 % nitric acid loaded weak base resin and topped by a strong acid cation resin (uppermost layer) simulating system flow velocity and percentage loading of resin. Using such a column it is demonstrated ...

Energy Technology Data Exchange (ETDEWEB)

The thermal spike model has been successfully applied to track formation by swift heavy ions in insulators. Arguments are given supporting the assumption that the thermal spike mechanism is also valid for the anisotropic growth. The glass transition temperature is used as the main thermal parameter of the amorphous solids. Experimental results on the track formation in {alpha}-quartz and in crystalline Ni{sub 3}B and also on the anisotropic growth in Pyrex and Synsil glasses, in amorphous Pd{sub 80}Si{sub 20}, Ni{sub 3}B and Fe{sub 85}B{sub 15} are discussed. Good agreement is found with the predictions of the thermal spike model. (orig.).

British Library Electronic Table of Contents (United Kingdom)

The southern Alaska convergent margin contains several small belts of sedimentary and volcanic rocks metamorphosed to blueschist facies, located along the Border Ranges fault on the contact between the Wrangellia and Chugach terranes. These belts are significant in that they are the most inboard, and thus probably contain the oldest record of Triassic-Jurassic northward-directed subduction beneath Wrangellia. The Liberty Creek HP-LT schist belt is the oldest and the innermost section of the Chugach terrane. Within this belt lawsonite blueschists contains an initial high-pressure assemblage formed by lawsonite+phengite+chlorite+sphene+albite+/-apatite+/-carbonates and quartz. Epidote blueschists are composed of sodic, sodic-calcic and calcic amphiboles+epidote+phengite+chlorite+albite+sphen...

British Library Electronic Table of Contents (United Kingdom)

SUMMARY Spontaneous potentials associated with volcanic activity are often interpreted by means of the electrokinetic potential, which is usually positive in the flow direction (i.e. Zeta potential of the rock is negative). The water-rock interactions in hydrothermal zones alter the primary minerals leading to the formation of secondary minerals. This work addresses the study of calcite precipitation in a sand composed of 98 per cent quartz and 2 per cent calcite using streaming potential measurements. The precipitation of calcite as a secondary mineral phase, inferred by high calcite saturation indices and by a fall in permeability, has a significant effect on the electrokinetic behaviour, leading to a significant reduction in the Zeta potential (in absolute value) and even a change in si...

International Nuclear Information System (INIS)

The feasibility of continuous production of gallium arsenide ribbon single crystals, by passage of a molten zone through boron-oxide encapsulated GaAs feedstock, is being investigated. Polycrystalline GaAs ribbons have been grown in graphite boats by passage of a wide zone through B2O3-encapsulated feed-stock, confined by a quartz cover plate. Failure to remove the encapsulant above its glass transition temperature, however, resulted in cracking of the ribbons on cooling to room temperature. In order to study the crucial zone melting step in isolation from the encapsulation steps of the continuous process, a constrained-zone melting apparatus has been constructed in which the boron oxide serves only as a sealant to suppress arsenic vaporization. Large grained polycrystalline samples have been produced with this apparatus.

International Nuclear Information System (INIS)

The effects of O and C ion implantation with different implantation doses on the yellow luminescence (YL) from unintentional doped n-type GaN have been studied by the photoluminescence (PL) spectra. O and C ions were implanted in the GaN samples with different doses from 1.0 x l013 to 1.0 x l017cm-2. Post-annealing was done in a quartz open-tube furnace under flowing N2 gas for 30 min at 950 degree C. By comparing with N ion implanted samples, it is assumed that different deep-level centers involving in the YL were produced in GaN after O and C ion implantation. In addition, with a dose of 1017 cm-2, the concentration of deep C centers involving in the YL was enhanced markedly. (authors)

Science.gov (United States)

The extraction and recovery of cesium from simulated Purex waste solutions was successfully demonstrated in the pilot plant pulse column. Stable volumetric capacities as high as 670 gph/ft/sup 2/ (sum of both phases) were obtained for alkaline supernate-type waste; however, for efficient operation (transfer unit height - HTU -of two feet or less), the maximum throughput rate was limited to about 500 gph/ft/sup 2/. This rate could be achieved with feeds diluted to densities within 0.08 g/cc of the solvent density. Stable feed was prepared from simulated current, denitrated waste by addition of citric acid to complex the iron before neutralization to the desired operating pH of 7 to 8. Capacities of 500 gph/ft/sup 2/ were readily achieved with this feed, together with HTU's of 1.0 to 1.3 feet. Sodium extracted with the cesium was satisfactorily scrubbed from the solvent with a dilute citric acid solution. Scrub section sodium ...

Energy Technology Data Exchange (ETDEWEB)

Several materials, lenses, dry bearings and cables were exposed to a tritiated moisture environment to study the behavior of tritium contamination on candidate materials for ITER remote handling equipment. To optimize the tritium removal procedure, decontamination experiments using a gas purge with three different moisture concentrations were also performed. The surface tritium concentrations of CeO{sub 2} containing alkaline barium glass (NB), CeO{sub 2} containing lead glass (LX) and synthetic quartz (Quartz) after the exposure experiments were 7.80, 10.94 and 0.67 Bq/cm{sup 2}, respectively. It was found that the tritium concentration was influenced by the compositions of the materials. The concentrations of tritium on type 831 (solid lubrication material: graphite) and type 237 (solid lubrication material: tungsten disulfate) dry bearings after the exposure experiments were 89.80 and 31.78 Bq/cm{sup 2}, respectively. The tritium ...

Energy Technology Data Exchange (ETDEWEB)

A petrographic comparison of Triassic, fluvial sandstones from the Deep River Basin in the eastern piedmont of North Carolina with nearby Holocene stream sands (1) indicates that he Triassic climate was more arid than today's and (2) distinguishes an eastern, more plutonic terrane from a western, more metamorphic source terrane. The paleoclimatic interpretation is based on differences in framework composition between modern and ancient sands of the same grain size, derived from the same rock type, transported similar distances and deposited in similar settings. The Triassic sandstones contain more lithic-fragments but less quartz than otherwise equivalent, modern sand in the Deep River Basin. Feldspar content is more complex, controlled by both source-rock composition and climate. Sand from the more plutonic terrane contains more feldspar and plutonic lithic-fragments than sand from the more metamorphic terrane, which contains more ...

Energy Technology Data Exchange (ETDEWEB)

Olive field is oil productive from a thin stratigraphically trapped sandstone within the Upper Cretaceous lower Tuscaloosa Formation. The discovery of Olive in 1981 led to renewed interest in the Mid-Dip Tuscaloosa Trend that continues today. Discovery and development was based on the correlation of the B sandstone to a mappable soft seismic event at a depth of 10,500 ft. The field was developed by 25 wells on 40-acre spacing. Olive has been waterflooded since 1983 and is a target for enhanced recovery using carbon dioxide. A total of 7.5 million stock tank bbl or approximately 75% of the original oil in place is estimated to be recoverable by conventional and enhanced recovery methods. The B sandstone was deposited by a northwest to southeast-flowing high-sinuosity meandering river system. Point bar, channel, and channel abandonment deposits are present. The point bar formed from the lateral migration of the river system from west to east, and channel abandonment is evident at the ...

Energy Technology Data Exchange (ETDEWEB)

The chemical thermodynamic concepts used in the calculation of solubility data of silica (quartz) are presented taking into account the PVT characteristics of water. The temperature-dependence trends between the thermodynamically calculated and the experimental quartz solubility data are very similar, but the values are widely different at high temperatures. The experimental solubility, especially along the saturation curve at high temperature and thermodynamic data for silica need to be reevaluated in order to use silica chemistry to understand geological processes. There could exist a wide range of values for silica solubility at a specified temperature, depending upon the amount of water in the reaction vessel. Thus the silica contents in geothermal fluid, in general, cannot be used as a geothermometer to estimate the reservoir temperature. The derivation of a silica geothermometer needs an extra assumption about the total amount of water in ...

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the energy required to separate ethanol from an aqueous solution in a distillation column containing a solid phase. The solid phases evaluated consisted of either an amylatious (ground corn) or a cellulose (sugar cane bagasse) absorber whit particle sizes smaller than 4 mm. The water-retention capacity of each solid phase was measured by passing vapors or ethanol-water mixtures through the solid phase. When starting with initial concentrations bellow the azeotropic point, ethanol concentrations up to 99,5% (on corn) and 97,2% (on sugar cane) were achieved. The water content was evaluated potentiometrically (Karl`Fischer). Regarding the 2-4 mm ground corn solid phase column, the energy consumed was estimated to be reduced by 15,6% and 60% (by weight) ethanol-water mixture respectively. (author) 11 refs., 2 figs., 2 tabs

Energy Technology Data Exchange (ETDEWEB)

When one deals with a plasma column whose radius a is much smaller than its length L, one can think of it as of a thin filament whose kink instability can be adequately described simply by a 2D displacement vector, {xi}{sub x} = {xi}{sub s}(z,t); {xi}{sub y} = {xi}{sub y}(z,t). Details of the internal structure of the column such as the current, density, and axial flow velocity distribution would be lumped into some phenomenological parameters. This approach is particularly efficient in the problems with non-ideal (sheath) boundary conditions (BC) at the end electrodes, with the finite plasma resistivity, and with a substantial axial flow. With the sheath BC imposed at one of the end-plates, we find instability in the domain well below the classical Kruskal-Shafranov limit. The presence of an axial flow causes the onset of rotation of the kink and strong axial ''skewness'' of the eigenfunction, with the ...

International Nuclear Information System (INIS)

Cobalt-60 gamma radiation has been found to be an effective means of immobilizing stationary phases onto gas and liquid chromatographic supports. The ability of a phase to crosslink was determined to be highly dependent on its chemical structure. Gamma radiation was employed to immobilize Se-30, a methylsilicone, and 216 PS onto Chromosorb WHP for packed column chromatography. The resultant columns exhibited increased thermal stability and a high degree of efficiency. Several blended phases containing varying ratios of Se-30:216 PS were also immobilized onto chromatographic packings. This work was further extended to the immobilization of Se-30 and 216 PS onto fused silica capillaries via gamma radiation. Columns exhibited excellent efficiency and improved thermal stability. An investigation into the role of immobilization of polymeric phases for HPLC was undertaken. Results indicate that gamma radiation can immobilzied ...

Energy Technology Data Exchange (ETDEWEB)

A procedure for the determination of carboxylic acids (benzoic and C{sub 8}-C{sub 16} aliphatic acids) in oxidised engine oils is described. It is based on a simple and selective derivatisation of the acids with a fluorescent label 9-anthracene-methanol followed by reverse-phase separation on an ODS column with a water-acetonitrile-tetrahydrofuran (20:40:40 by volume) mobile phase and post-column reaction with bis(2,4-dinitrophenyl) oxalate and hydrogen peroxide. The chemiluminiscence emission from the reaction was monitored using a lamina flow-through detector. Analysis of oxidised oils showed that although there was quenching of chemiluminiscence emission by the oil matrix, the acids could be determined over the range 0-0.4% (m/v) in the oil with a detection limit of 0.013% (m/v) (130 pmol on-column with a 20 {mu}l injection) for lauric acid. 8 figs., 2 tabs., 17 refs.

Energy Technology Data Exchange (ETDEWEB)

One of the important aspects in an absorption system is the effectiveness in which the gas and liquid phases come into contact with each other. An effective absorption process will provide sufficient contacting area for the gas and liquid phases to interact upon. With this in mind, work was conducted to evaluate carbon dioxide (CO{sub 2}) absorption into aqueous solutions of monoethanolamine (MEA) using two different types of contacting devices: gas absorption membrane (GAM) modules and traditional packed columns. The performance of these two absorption devices was compared to one another using the overall mass transfer coefficient (K{sub G}a{sub v}) as a basis. The GAM module contained microporous polypropylene hollow fibre membranes and the packed absorption column contained Sulzer DX structured packing. The results indicate that GAM modules tend to have slightly larger K{sub G}a{sub v} values, potentially opening the door for smaller ...

International Nuclear Information System (INIS)

Homidium bromide and isometamidium chloride are used extensively in the treatment of bovine trypanosomiasis in Africa, but no specific and sensitive method to detect the drug in plasma has been published yet. Comparing the methods of other investigators it was found that they could not overcome the protein binding of these drugs which reduced the available and determined drug to 10% of the real concentrations. These techniques overcome the protein binding by enzyme digestion and an alteration of the pH before adding the sample directly on clean-up columns. Drug recover rates above 80% were obtained. For the detection, the HPLC was employed using a C18 reversed phase analytical column and UV detection, determining both drugs as intact molecules. (author).

Energy Technology Data Exchange (ETDEWEB)

A simple method is presented for the separation of lead-203 from copper-backed thallium cyclotron targets. The procedure involves cation-exchange chromatography in hydrochloric acid and hydrochloric acid-acetone mixtures. Further purification involves anion-exchange chromatography in nitric acid-hydrobromic acid mixtures. A cation-exchange column containing 3.0 g of resin can handle as much as 15 g of thallium and 160 mg of copper. An anion-exchange column containing 3.0 g of resin can separate lead from up to 200 mg of thallium and 10 mg of copper. Separations are extremely sharp and less than 0.1 ..mu..g of thallium and less than 0.1 ..mu..g of copper remain in the lead-203 fraction.

British Library Electronic Table of Contents (United Kingdom)

This experimental study investigates the effectiveness of crossed inclined bars (X-bars) as joint shear reinforcement in exterior reinforced concrete beam-column connections under cyclic deformations. Test results of 20 joint subassemblages with various reinforcement ratios and arrangements including X-bars in the joint area are presented. The X-type, non-conventional reinforcement is examined as the only joint reinforcement and in combination with common stirrups or vertical bars. The experimental results reported herein include full loading cycle curves, energy dissipation values and a categorization of the observed damage modes. Based on the comparisons between the overall hysteretic responses of the tested specimens, it is deduced that joints with X-bars exhibited enhanced cyclic perfo...

Science.gov (United States)

Generally the photonic band gap (PBG) is a multi-variable function of several parameters related to the shape and size of the dielectric columns of photonic crystals (PhCs), and a time-consuming step-by-step scanning process for each parameter has to be used to find their best combination yielding maximum PBG. In this letter, the widely used Nelder-Mead simplex algorithm is introduced to optimize these parameters simultaneously to find a larger PBG for a new kind of two-dimensional (2D) hexagonal GaAs-Air PhC. This structure can be conveniently produced by the single-exposure holographic lithography, and the specific holographic design is also systematically investigated. This study reveals that the band gaps of PhCs made by holographic lithography may be widened by introducing irregularity of the columns and lowering the symmetry of the structure.

Energy Technology Data Exchange (ETDEWEB)

Real-time neutron radiography was demonstrated to be a viable and useful tool in studying water flow in unsaturated media. The experiment was designed to test the method for following water flow. The wetting front advance, water-flow patterns, and neutron attenuation density were observed in a 7.7-cm diameter sand column. The advance was fit with a simple i = A t/sup B/ equation yielding an excellent correlation. Theoretical calculations presented estimate the minimum and maximum detectable water content in various sizes of columns. The ability of real-time neutron radiography to allow both qualitative and quantitative spatial and time measurements to be made in an nonintrusive manner was demonstrated.

CERN Document Server

The Nystrom method is an efficient technique to speed up large-scale learning applications by generating low-rank approximations. Crucial to the performance of this technique is the assumption that a matrix can be well approximated by working exclusively with a subset of its columns. In this work we relate this assumption to the concept of matrix coherence and connect matrix coherence to the performance of the Nystrom method. Making use of related work in the compressed sensing and the matrix completion literature, we derive novel coherence-based bounds for the Nystrom method in the low-rank setting. We then present empirical results that corroborate these theoretical bounds. Finally, we present more general empirical results for the full-rank setting that convincingly demonstrate the ability of matrix coherence to measure the degree to which information can be extracted from a subset of columns.

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of an experimental programme to determine the mass transfer and sorptive properties of selected glacial sand and clays from the Drigg Disposal Site operated by British Nuclear Fuels plc. The hydraulic conductivity of both the sand and clay has been determined and the sensitivity of this parameter to changing water chemistry investigated. The hydrodynamic dispersion properties of the glacial sand were measured in order to aid the interpretation of column sorption experiments. The sorption of strontium and uranium from groundwater onto clay and sand samples has been studied using through-diffusion, column and batch techniques. Employing the batch technique, the effect of a series of humic acid concentrations on distribution ratios for uranium and plutonium has also been investigated. Groundwater and trench leachate were used with both clay and sand. (author).

International Nuclear Information System (INIS)

Antibodies to hemoglobin have been studied with a radioimmunoassay which employs ["1"4C]carbamylated (= carbamoylated) hemoglobin S. An antiserum raised against hemoglobin S, which initially discriminated poorly between hemoglobins S and A, was fractionated by absorption to a column of Sepharose to which a synthetic peptide corresponding to the first 13 amino-acid residues of the #beta# chain of sickle hemoglobin had been covalently bound. A subpopulation of the antiserum was eluted from this column with 4 M guanidine . HCl. These antibodies showed binding to hemoglobin S but not to hemoglobin A and this interaction could be inhibited by the synthetic peptide. These antibodies, of demonstrated fine structural specificity, may be useful in the detection of sickle hemoglobin and in the study of its structure in solution.

International Nuclear Information System (INIS)

Twenty-two patients with vertebral primaries were registered in the Intergroup Ewing's Sarcoma Study between 1973 and 1977. The radiation doses to the primary tumors ranged between 3800 and 6200 rad. All patients received intensive combination chemotherapy. After a followup ranging between 14 and 62 months, 14 patients remained disease-free. All patients with primary tumor of the cervical and dorsal spine remained disease-free. Of eight patients with lesions in the distal spine, (sacrococcygeal region) six developed recurrence, in three a local recurrence was observed despite doses of 6000 rad or higher. Doses of 5000 rad or less (in addition to combination chemotherapy as used in the Intergroup Ewing's Study) appear adequate in controlling the primary tumors of the proximal segments of the spinal column.

Scientific Electronic Library Online (English)

Abstract in english A mathematical model has been developed for describing the dynamic operation of the N-formylmorpholine extractive distillation column and the corresponding solvent recovery column in the benzene extraction plant. The NRTL equation was used to calculate the equilibrium and thermodynamic properties of the mixtures. The validity of the model in terms of temperature, pressure and split fraction was examined using actual plant data at steady-state conditions. Comparison betwee (more) n model results and plant data shows good consistency. In order to improve the control of the process and selection of the optimal control strategy, the model was used to find the optimum values of the constants of the controllers with Nelder-Mead algorithm during unsteady-state operation by minimizing the deviation from steady-state conditions. The outcome of this study could be used by operators and engineers to increase the productivity of the ...

British Library Electronic Table of Contents (United Kingdom)

Abstract In the work, a rapid, simple and high-throughput sample preparation method was developed for the determination of sulfonamide (SA) antibiotic residues in chicken breast muscle. The extraction and clean-up were online combined and up to 20 samples can be treated simultaneously in 6-min. The SAs were first extracted with acetonitrile under the action of microwave energy, and then the extract was directly introduced into the SPE column for on-line clean-up and concentration. Subsequently, the SAs eluted from the SPE column were determined by liquid chromatography-tandem mass spectrometry. The precisions of extraction results of 20 samples were in the range of 4.9-7.4%. The limits of detection and quantification obtained were in the range of 2.4-3.6-ng/g and 8.6-11.3-ng/g for SAs, res...

International Nuclear Information System (INIS)

Full Text: Smallstage Dualbeam (SDB) systems, that is a Focussed Ion Beam column coupled with a SEM column, have been around for about five years now. There impact on the Semiconductor industry has been enormous, with virtually every lab having a SDB to produce, characterise and analyse cross sections and TEM samples on the Nano-scale. But what about other industries? What else can SDB system be used for? The SEM column in itself is a very powerful tool for sample characterisation, modification and analysis. An electron beam from a Tungsten or Thermal Field Emission source has enough current to allow sophisticated patterns to be created in photo-resist samples, a process known as lithography. The current is also high enough to allow for a process known as Electron Beam Induced Deposition (EBID), where the beam interacts with an introduced gas and material is deposited in a controlled manner on the sample. With the addition ...

International Nuclear Information System (INIS)

The harmful effect of phosphate in yellow cake on the TBP purification process and its removal methods are dealed with. The reason of more uranium loss in residue was analyzed. The harmful effect of phosphate on TBP extraction efficiency and operaton of extraction column was discussed. The limit value of uranium concentration in digestion solution was presented. For TBP purification process, the presence of phosphate in yellow cake does more harm than good. (authors)

Energy Technology Data Exchange (ETDEWEB)

Presented are some preliminary studies made in preparation for the design of a solar powered loop for desalination by humidification - dehumidification process. The studies concentrated on the evaluation of different parameters affecting the performance of the combination of different components in such a loop in the hope of outlining the most decisive factors for the choice or design of solar collectors or heat source. The results presented relate to the performance of two of the most important components in a loop of such purpose, that is: the humidifying and the dehumidifying columns or stacks. 4 refs.

Energy Technology Data Exchange (ETDEWEB)

The degradation of chlorinated solvents by reduction at the surface of zero-valent metals and bimetallic systems has emerged as an important approach to the in-situ remediation of ground water. Reduction by iron metal was studied in batch and column systems to develop a mechanistic understanding of the reaction chemistry and to determine the factors that affect dechlorination rate and long term performance in field applications.

Wastenet

... Further complications resulted from the requirement to use existing piled foundations and columns which had originally been designed to accommodate a six-storey office block. The hotel bedroom configurations and planning constraints were different from thos Related Services Structural Design Go View all Services Find Projects Sector All Sectors Buildings & Infrastructure Environment Natural Resources Transportation Sub Sector All Sub-Sectors Country All Countries Angola Antigua and Barbuda Argentina Australia Azerbaijan ...

Energy Technology Data Exchange (ETDEWEB)

In studying the absorption of carbon dioxide by absorbents impregnated with alkanol amines, researchers used a laboratory-scale packed column to determine the overall gas-phase mass-transfer coefficients and enhancement factors. A model derived for the mechanism of the chemical reaction taking place in the interfacial layer accounts for the effect of the reaction upon the absorption rate better than other models.

International Nuclear Information System (INIS)

Results of americium-242m and americium-242 preparation by irradiating initial americium-241 at a reactor in the form of a diphtalocyanine complex are presented. The enrichment coefficient, equalling 10, has been obtained using the extraction method of recoil atom separation from the parent isotope. Application of the chromatographic column with Dowex-50 permits to increase the enrichment coefficient of isotopes upto 24.6.

International Nuclear Information System (INIS)

Americium 242m and americium 242 were prepared by reactor irradiation of americium 241 as its diphthalocyanine complex. The product atoms were extracted from the parent isotope at an enrichment factor of 10. A Dowex 50 chromatographic column raised the factor to 24.6.

Energy Technology Data Exchange (ETDEWEB)

An equation is described to estimate the value of the liquid-phase mass-transfer coefficient of aqueous solutions of surfactants from its value for pure water. The form of the equation is obtained from Levich's theory, and it is adjusted to experiments of absorption of CO/sub 2/ in aqueous solutions of five pure surfactants. The reduction of the absorption rate is correlated with the interfacial pressure of the solution.

Energy Technology Data Exchange (ETDEWEB)

A radiochemical method of separation of {sup 203}Hg from {sup 181}Hf is described. The method involves separation by Dowex 50W- X 8, 100-200 mesh, cation exchange resin using 1 M hydrochloric acid as the eluant. The chemical yield for the separation of mercury is > 85% and the decontamination factor is >10{sup 4}. The {sup 181}Hf can be eluted from the column by 4 M HCl.

Energy Technology Data Exchange (ETDEWEB)

Red mud, which is a pollutant residue from the extraction of alumina from bauxite ore, was utilized as an additive to a well blended mixture of three Egyptian clays, feldspar, quartz and grog. This was added in gradual proportions to study its effect on the vitrification properties of fired samples. Samples were moulded under a pressure of 20.7 MPa and fired at temperatures ranging from 950 C to 1100 C for soaking periods up to three hours. Compressive strength was determined as function of percent red mud added and firing temperature. A semi-exponential relation was established between strength and apparent porosity. 50 x 50 mm tiles containing 70% red mud addition and fired at 1100 C for one hour were tested. They were found to match the standards required for glazed wall tiles bodies. Tiles fired at 1100 C for 3 hours were compatible with the standards for glazed floor tiles. (orig.)

International Nuclear Information System (INIS)

Control of thermal expansion is often necessary in the design and selection of electronic packages. In some instances, it is desirable to have a coefficient of thermal expansion intermediate between values readily attainable with single or two phase materials. The addition of a third phase in the form of fillers, whiskers, or fibers can be used to attain intermediate expansions. To help design the thermal expansion of multiphase materials for specific applications, a closed form model has been developed that accurately predicts the effective elastic properties of isotropic filled materials and transversely isotropic lamina. Properties of filled matrix materials are used as inputs to the lamina model to obtain the composite elastic properties as a function of the volume fraction of each phase. Hybrid composites with two or more fiber types are easily handled with this model. This paper reports that results for glass, quartz, and Kevlar fibers with beta-eucryptite ...

Energy Technology Data Exchange (ETDEWEB)

Thermal gradients and thermal conductivities were obtained in real time using an in situ heat-flow technique in 15 shallow (90 to 150 m) wells drilled between Brawley and Glamis in the Imperial Valley, Southern California. The in situ measurements were supplemented by follow-up conventional temperature logs in seven of the wells and by laboratory measurements of thermal conductivity on drill cuttings. The deltaic sedimentary material comprising the upper approx. 100 m of the Salton Trough generally is poorly sorted and high in quartz resulting in quite high thermal conductivities (averaging 2.0 Wm/sup -1/ K/sup -1/ as opposed to 1.2 to 1.7 for typical alluvium). A broad heat-flow anomaly with maximum of about 200 mWm/sup -2/ (approx. 5 HFU) is centered between Glamis and East Brawley and is superimposed on a regional heat-flow high in excess of 100 mWm/sup -2/ (> 2.5 HFU). The heat-flow high corresponds with a gravity maximum and partially with a minimum in ...

Energy Technology Data Exchange (ETDEWEB)

Monodisperse noble metal nanoparticles are of tremendous interest for numerous applications, such as surface-enhanced Raman spectroscopy, catalysis or biosensing. However, preparation of monodisperse metal nanoparticles is still a challenging task, because typical preparation methods yield nanoparticle ensembles with broad shape and/or size distributions. To overcome this drawback, tailoring of metal nanoparticles with laser light has been developed, which is based on the pronounced shape- and size-dependent optical properties of metal nanoparticles. I will demonstrate that nanoparticle tailoring with ns-pulsed laser light is a suitable method to prepare nanoparticle ensembles with a narrow shape and/or size distribution. While irradiation with ns-pulsed laser light during nanoparticle growth permits a precise shape tailoring, post-grown irradiation allows a size tailoring. For example, the initial broad Gaussian size distribution of silver nanoparticles on quartz ...

British Library Electronic Table of Contents (United Kingdom)

Ferroelectric barium strontium titanate (Ba0.7Sr0.3TiO3)(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH3(CH2)3CH(C2H5)CO2]2], strontium 2-ethylhexanoate [Sr[CH3(CH2)3CH(C2H5)CO2]2] and titanium(IV) isopropoxide [TiOCH(CH3)2]4 precursors using a modified sol-gel technique. The precursor except [TiOCH(CH3)2]4 were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550degreeC for 1h in air. The lattice constants "a" and "c" were found to be 3.974A and 3.990A, respectively. The grain...

Energy Technology Data Exchange (ETDEWEB)

An experimental study of the hydrodynamics of a narrow channel was performed in order to obtain the heat transfer mechanisms and influences contributing to the flow regime transition from inverted annular to inverted slug flows for post dryout downflow. The experimental series consisted of both adiabatic and diabatic visualization tests over a wide range of fluid and thermal parameters. The system inlet gas velocities ranged from 0 to 14 meters per second while the inlet fluid velocities ranged from 1 to 3 meters per second. Full extent visualization of the flow regime was possible due to a quartz tube in tube construction with a clear heating fluid. Constant temperature heating of the freon was accomplished at bulk fluid temperatures above the critical heat flux temperature. For each hydrodynamic flow condition, one to three minuets of VHS-video filming was performed to acquire both flow regime and break-up length data. In addition to this the flow field ...

Energy Technology Data Exchange (ETDEWEB)

We have developed an ion probe technique for the in situ measurement of oxygen isotope ratios, {sup 18}O/{sup 16}O and {sup 17}O/{sup 16}O, with high spatial resolution in polished thin sections of silicate minerals. This technique allows the isotopic analysis of samples as small as picomoles of material which represents only 10{sup -7} of the sample size required by conventional fluorination oxygen isotope measurement methods and thus has wide application to the study of many terrestrial and extra-terrestrial samples that have heterogeneous oxygen isotope compositions on a scale of tens of micrometres. To illustrate the breadth of studies that are made possible by the ion probe, we report here oxygen isotope measurements from an authigenic quartz overgrowth obtained from the Penrith sandstone, UK, and measurements of magnetite grains from the Orgueil and Yamato 82162 carbonaceous chondrites which may be used to constrain possible formation mechanisms of the ...

Energy Technology Data Exchange (ETDEWEB)

Past movement on faults can be dated by measurement of the intensity of ESR signals in quartz. These signals are reset by local lattice deformation and local frictional heating on grain contacts at the time of fault movement. The ESR signals then grow back as a result of bombardment by ionizing radiation from surrounding rocks. The age is obtained from the ratio of the equivalent dose, needed to produce the observed signal, to the dose rate. Fine grains are more completely reset during faulting, and a plot of age vs. grain size shows a plateau for grains below critical size; these grains are presumed to have been completely zeroed by the last fault activity. We carried out ESR dating of fault rocks collected near the Gori nuclear reactor. Most of the ESR signals of fault rocks collected from the basement are saturated. This indicates that the last movement of the faults had occurred before the Quaternary period. However, ESR dates from the Oyong fault zone range ...

Energy Technology Data Exchange (ETDEWEB)

The need for a hydrogen economy is driven by increasing fuel prices, depleting oil reserves and uncertainty over supplies, and concerns about global warming and environmental pollution. Alternative methods to portable energy sources such as fossil fuels are being developed that are more efficient and carbon-emission-neutral. A prospective method is to produce hydrogen as an energy carrier. This paper presented a study on the degradation of materials under conditions of the sulphur-iodine (SI) thermochemical cycle. The paper provided background information on the study and presented a schematic of the SI cycle. A literature review was presented along with materials selected, such as refractory metals, reactive metals, superalloys, glassy metals, ceramics, cermets, polymers, composites, and coatings. The experimental method was then described. A capsule method was developed to rapidly quantify the decomposition rate of the candidate materials under the target conditions of temperature, ...

British Library Electronic Table of Contents (United Kingdom)

This study addresses the solar thermal decomposition of natural gas for the co-production of hydrogen and carbon black (CB) as a high-value nano-material with the bonus of zero CO2 emission. The work focused on the development of a medium-scale solar reactor (10kW) based on the indirect heating concept. The solar reactor is composed of a cubic cavity receiver (20cm-side), which absorbs concentrated solar irradiation through a quartz window by a 9cm-diameter aperture. The reacting gas flows inside four graphite tubular reaction zones that are settled vertically inside the cavity. Experimental results in the temperature range 1740-2070K are presented: acetylene (C2H2) was the most important by-product with a mole fraction of up to about 7%, depending on the gas residence time. C2H2 content i...

Energy Technology Data Exchange (ETDEWEB)

This work is directly to analysis of atmosphere surrounding Ipiranga Refinery; witch is located in the city of Rio Grande, in estate of Rio Grande do Sul. The refinery is surrounded by neighborhood, witch are impacted by atmospheric emissions of refinery. The objective of this work is correlating the refinery to the inhabitants that lives near the refinery, using an environmental sustainability index. This work will be achieve by analysis of Polycyclic Aromatic Hydrocarbons (PAH) bounded in particulate matter with diameter of 100 {mu}m (PTS), the acquisition of health data on the city hospitals and correlation of this data with PAH concentrations in Particulate Matter. The Samples were obtain by FEPAM, witch have three samples sites in the center of city. The samples was obtained by a High Volume Sampler equipped with quartz fiber filters. The meteorological data important to this work, like wind direction and speed, will be obtain in Meteorological Station on ...

Energy Technology Data Exchange (ETDEWEB)

This paper evaluates abrasive jet wear tests, carried out on the ZUK-3M abrasion apparatus according to the GOSF 23.201-78 industrial standard. As abrasive material, brown coal coke dust, brown coal dust, power plant fly ash and quartz sand (for the purpose of comparison) were employed. Seventeen types of materials were blasted with abrasive jets, including a selection of steels, glass, rubber, SYS-pur plastics, cast basalt, Kawenit and vitroceramics. The test apparatus produced abrasive jet velocities between 12 and 130 ms/SUP/-/SUP/1 at rotor revolutions of 1,000 to 10,000 min/SUP/-/SUP/1. Blasted material samples were arranged at angles between 15 and 90 degrees. Various tables and graphs present abrasivity results. These results were employed for technical modifications of dedusting equipment in briquetting and coking plants, which led to a threefold increase in service life of abrasion endangered equipment parts. (8 refs.) (In German)

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: The heat transfer and flow in narrow channels has lots of advantages such as compact structure, high efficiency, design flexibility and so on. So it is widely used in the fields such as the new reactor core plate elements, the once-through stream generator, compact heat exchangers as well as electronic components. In recent years, more strong attentions have been attracted to the thermal-hydraulic characteristics and mechanism of the two-phase flow in narrow channels. As the flow regime characteristics of two-phase flow is fundamental one of them, the research on the two-phase flow regimes and the regime transitions in horizontal rectangular narrow heated channels can provide theoretical foundation and engineering directions to the whole research on the thermal-hydraulic characteristics and mechanism of the two-phase flow in narrow channels. The characteristics of two-phase flow regimes and regime transitions of boiling water in horizontal rectangular ...

Energy Technology Data Exchange (ETDEWEB)

The activity concentrations of potassium, uranium and thorium in minerals and soil samples from a mining site in Ibadan, Southwestern Nigeria were measured using gamma ray spectroscopy method. Effective dose per annum has been calculated from the activity concentrations of dominant gamma-emitting natural radionuclides, potassium, uranium and thorium. Samples collected include minerals (beryl, quartz and feldspar), soil samples from the mining pits, heaps and undisturbed land around the mining site. The activity concentrations of {sup 40}K, {sup 238}U and {sup 232}Th, respectively in Bq kg-1 in the mineral samples were as follows: 1985 +- 16, 4.8 +- 0.9 and 11.8 +- 5.8 for beryl sample, 115.1 +- 27.9, 5.0 +- 1.3 and 6.3 +- 5.0 for feldspar samples and 1421 +- 122, <4.8 and 20.1 +- 3.5 for quartz samples. For the soil samples, the mean activity concentrations of {sup 40}K, {sup 238}U and {sup 232}Th, respectively, were 314.2 +- 5.7, 27.7 ...

International Nuclear Information System (INIS)

Service water, 100 l each, was collected at an intake of a water treatment plant and at a tap after water was left running for five minutes. The carriers of strontium and cesium were added to water immediately after sampling, and the sample was vigorously stirred and filtered. Then it was passed through a cation exchange column at a rate of 80 ml/min. Strontium and cesium were eluted with hydrochloric acid from the cation exchange column, and separated. After the radiochemical separation, the mounted precipitates were counted for activity using low background beta counters normally for 60 min. Net sample counting rates were corrected for counter efficiency, recovery, self absorption and decay to obtain the content of strontium-90 and cesium-137 radioactivity per sample aliquot. From the results, concentrations of these nuclides in the original sample were calculated. The maximum values obtained were 0.29 pCi/l of Sr-90 in Kyoto in August, 1981, ...

Science.gov (United States)

Newly commercialized Fourier transform Raman spectroscopic instrumentation provides a simpler alternative for vibrational spectroscopic analysis. Instrument vendors currently design for laboratory use, but there are many potential process applications of these stable, easy to use instruments. Raman spectroscopy is highly suited to analysis of aqueous samples. Near infrared excitation minimized fluorescence interference and allows for remote operation via fiber optic probes. The Department of Energy has funded research at the Measurement and Control Center to establish the utility of this method for on-line composition analysis in distillation columns. Laboratory evaluation and instrument employs an air-cooled laser and a thermoelectrically cooled detector. The device is mounted on a three by foot cart for convenient location in control rooms. Current fiber optic extension cables allow for analysis in a cell thirty five meters from the instrument. Application of the ...

Energy Technology Data Exchange (ETDEWEB)

A brief comparative review of possible mercury free fluorescent lighting technologies is presented, including rare-gas positive column discharges, molecular discharges, and dielectric barrier discharges. Detailed experimental results on xenon positive column discharges will then be considered. In order to judge whether xenon-based discharges are a viable UV source it is necessary to measure the radiant emittance (power per unit area) for the vacuum ultraviolet (VUV) resonance xenon emission at 147 nm. Two techniques to determine the VUV radiant emittance have been developed and applied to xenon discharges. One method combines the measured resonance level density using absorption spectroscopy and a calculation of the trapped decay rate for the resonance radiation to arrive at the radiant emittance at 147 nm. A second method utilizes a direct measurement of the radiance (power per unit area per unit solid angle) at 147 nm using a calibrated VUV ...

International Nuclear Information System (INIS)

One way to intensify heat and mass transfer processes in column-type equipment is through use of contact devices with directional gas phase injection into a liquid. Making the perforations at an angle to the tray plane permits a rise in the permissible gas velocity in the column, since inertial force adds to gravity during separation. Different arrangements of the jet-forming elements relative to one another and to partitions and baffle-type contacts installed on the trays can improve phase contact conditions and intensify heat and mass transfer. Design of jet-type trays for a specific purpose requires that the influence of jet-forming, element design parameters on at least the fluid dynamic situation on the tray be known. In this work, the authors evaluate the influence of tab bend-up angle on jet tray working characteristics. These investigations demonstrate that the jet inclination angle (the angle of maximum gas velocity in the jet) exceeds ...

Energy Technology Data Exchange (ETDEWEB)

The effects of therapeutic levels of radiation on the axial properties of the primate vertebral column were studied. Seven male rhesus monkeys (Macaca mulatta) were irradiated with a single does of 1300 cGy to the specific lumbar vertebrae of L2, L3, and L4. Three additional animals served as controls. Radiographs were taken before the radiation treatment and just prior to sacrifice to determine density changes in the bone. The animal subjects were sacrificed 105 days following the radiation exposure. Biomechanical testing was completed on lumbar levels 2 and 3 to identify changes in strength characteristics following radiation treatment. Histomorphometric analysis of lumbar vertebrae level 4 was completed to identify volume and surface density changes as well as cellular changes. Tetracycline, dicarbomethylaminomethyl fluorescein (DCAF), and xylenol orange were used as bone labeling agents to aid in the histomorphometry and to obtain dynamic parameter changes.

Energy Technology Data Exchange (ETDEWEB)

The desorption of uranium from the granular titanium-activated carbon composite adsorbent (concentration of uranium: 25.5 mg/l-Ad), which adsorbed uranium from natural sea water, was examined by the column process with acidic eluent at room temperature. The column operation was able to be carried out without destruction of the granular adsorbent by the generation of the carbon dioxide, and free from disturbance of the eluent flow by precipitate of calcium sulfate dihydrate with sulfuric acid eluent. The amount of acid consumption by the adsorbent was 0.87 eq/l-Ad. The alkaline earth metals were eluted in the range of elution volume below 2l/l-Ad, whereas uranium, iron, and titanium were eluted above 2l/l-Ad. Therefore, uranium was separable from the alkaline earth metals which were adsorbed in the most quantity in the adsorbent. In the range of elution volume 2 to 12l/l-Ad, the percentage of desorbed uranium and the concentration ratio of ...

International Nuclear Information System (INIS)

Neutron semiconductor detectors for neutron counting and neutron radiography have an increasing importance. Simple silicon neutron detectors are combination of a planar diode with a layer of an appropriate neutron converter such as 6LiF. These devices have limited detection efficiency of not more than 5%. The detection efficiency can be increased by creating a 3D microstructure of dips, trenches or pores in the detector and filling it with a neutron converter. The first results related to the development of such devices are presented. Silicon detectors were fabricated with pyramidal dips on the surface covered with 6LiF and then irradiated by thermal neutrons. Pulse height spectra of the energy deposited in the sensitive volume were compared with simulations. The detection efficiency of these devices was about 6.3%. Samples with different column sizes were fabricated to study the electrical properties of 3D structures. Charge collection efficiencies in silicon ...

Energy Technology Data Exchange (ETDEWEB)

In a study where the removal of heavy metals from wastewater is the primary aim, the biosorption of heavy metals onto biosolids prepared as Pseudomonas aeruginosa immobilized onto granular activated carbon was investigated in batch and column systems. In the batch system, adsorption equilibriums of heavy metals were reached between 20 and 50 min, and the optimal dosage of biosolids was 0.3 g/L. The biosorption efficiencies were 84, 80, 79, 59 and 42 % for Cr(VI), Ni(II), Cu(II), Zn(II) and Cd(II) ions, respectively. The rate constants of biosorption and pore diffusion of heavy metals were 0.013-0.089 min{sup -1} and 0.026-0.690 min{sup -0.5}. In the column systems, the biosorption efficiencies for all heavy metals increased up to 81-100 %. The affinity of biosorption for various metal ions towards biosolids was decreased in the order: Cr = Ni > Cu > Zn > Cd. (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Wastewater from a food-manufacturing plant with a low concentration of organic matter was treated at 37 centigrade in an anaerobic fluidized-bed reactor or in an upflow anaerobic sludge blanket. As the influent TOC (total organic carbon) concentration decreased, the TOC removal efficiency in these reactors decreased from 85% to 65%. The concentration of suspended solids in the effluent could be reduced to 20 mg/l, which corresponded to 7% of that in the influent. The effluent from both reactors was treated aerobically in a fixed-bed reactor. The TOC concentration and optical density of effluent from the aerobic treatment were reduced to 5 mg/l and 0.005, respectively. When the effluent treated anaerobically or aerobically was passed over an activated carbon column, the effluent TOC concentration was reduced to 2 to 3 mg/l. The conductivity in raw wastewater was remarkably reduced on an ion-exchange resin column. Ultra-pure water for industrial ...

Environmental Research Database

SummaryInitial results from the use of activated dolomite from QUESTOR project L1 have proved extremely encouraging in terms of metallic ion (also phosphate, nitrate and dye) removal from wastewater, with capacities in some instances in excess of commercially available activated carbons.This new project involves investigating actual plant effluent in laboratory scale columns and the design of a pilot scale rig for on site trials. The project also involves investigating disposal options and an economic [continued...

International Nuclear Information System (INIS)

The effects of various approximations used in performing augmented-plane-wave calculations were studied for elements of the fifth and sixth columns of the Periodic Table, namely V, Nb, Ta, Cr, Mo, and W. Two kinds of approximations have been checked: (i) variation of the number of k points used to iterate to self-consistency, and (ii) approximations for the treatment of the core states. In addition a comparison between relativistic and nonrelativistic calculations is made, and an approximate method of calculating the spin-orbit splitting is given.

Energy Technology Data Exchange (ETDEWEB)

Production decline-curve analysis is accepted for prediction of future performance of oil and gas wells and fields. One type of decline-curve analysis involves the hyperbolic-decline-curve equation. The challenge with this equation is to determine simultaneously three parameters. The new method creates a computer spreadsheet containing a set of production data. Then, the specific arrangement of cells and columns containing data and/or formulas allows for statistical fits of the data. Finally, setting-up the nonlinear solver allows for optimization of the three parameters by maximization of the square of the regression coefficient. Eight field cases demonstrated the repeatable and rapid curve-fitting of the method.

Energy Technology Data Exchange (ETDEWEB)

Separations of metal ions on the basis of Donnan dialysis across anion-exchange membranes should be possible if the receiver electrolyte composition favors the formation of selected anionic complexes of the sample metal ions. Moreover, such a separation has the possibility of being better suited from some applications than batch or column experiments with anion-exchange resins. The above hypothesis are tested on the platinum-group metal ions, Pt(IV), Rh(III), Pd(II), Ir(III), and Ir(IV). 13 references, 4 tables.

British Library Electronic Table of Contents (United Kingdom)

There is strong interest in lithium imaging, particularly because of its significance in battery materials. However, light atoms only scatter electrons weakly and atomic resolution direct imaging of lithium has proven difficult. This paper explores theoretically the conditions under which lithium columns can be expected to be directly visible using annular bright field scanning transmission electron microscopy. A detailed discussion is given of the controllable parameters and the conditions most favourable for lithium imaging.

International Nuclear Information System (INIS)

In the present paper we propose a model of physical phenomena behind the front face of the electrodes in an impulse plasma accelerator. The model is based on the results of recent experimental observations and measurements. It correlates plasma dynamics with mechanism of phenomena in a column of pinching plasma. On the contrary to the previous model the current one suggests the series of relatively short pulses of metallic ions from the erosion of electrode material. Till now the pinch was treated rather as a nearly continuous source of metallic plasma, feeding the process with ions from the erosion of electrode material. (author)

Energy Technology Data Exchange (ETDEWEB)

Papers in this book illustrate the utility of mineral biotechnology with respect to biobeneficiation, bioleaching, bioremediation and biomineralization. Papers of particular interest to the coal industry include: depression of pyrite flotation by yeast and bacteris (S.K. Kawatra and T.C. Eisele); desulfurization of coal by microbial flotation in a semicontinuous system (T. Nagaoka and others); biochemical removal of HAP precursors from coal - INEEL slurry column testing (K.S. Noah and G.J. Olson); microorganisms, biotechnology and acid rock drainage - emphasis on passive-biological control and treatment methods (N. Kuyucak); and utility of bioreagents in mineral processing (P. Somasundaran and others).

International Nuclear Information System (INIS)

Effects of the rapid early-in-life expansion of metal fuel were measured in an irradiation experiment in the Fast Flux Test Facility (FFTF). This important performance/design information was obtainable through the unique combination of a dimensionally stable FFTF oxide core and the calibrated proximity instrumentation associated with the test. These results delineate the time dependence of metal-fuel swelling and provide quantitative estimates of the magnitude of axial fuel swelling in full-length metal-fuel assemblies. Final posttest examination results will define actual fuel column growth levels.

Energy Technology Data Exchange (ETDEWEB)

A packed column was used for investigating the desorption rate of CO{sub 2} from aqueous methyldiethanolamine (MDEA) and activated MDEA solutions. Experiments were conducted within the temperature range 30--70 C, the concentration of MDEA was 4.28 kmol/m{sup 3}, and the concentration of piperazine (PZ) was 0.10 kmol/m{sup 3} for aqueous activated MDEA solutions. Experimental data confirmed that the kinetics model of absorption CO{sub 2} into aqueous MDEA and activated MDEA solutions can be applicable to the situations in which desorption occurs, and the desorption rate of model predictions agree well with that of experimental determination.

Energy Technology Data Exchange (ETDEWEB)

The integrity of the RPV head and reactor internals was assessed by means of fluid-structural analyses using a coupled method to evaluate the water hammer phenomenon arising from high burnup fuel failure under RIA conditions. The fluid viscosity effect on the water column burst as well as the complex three-dimensional flow paths caused by a core shroud and standpipes were considered in this study. The three analysis scenarios were designed to investigate the above mentioned influential factors separately. In the first scenario, a two-dimensional axisymmetric reactor vessel model without any reactor internals was modeled to assess the influence of the fluid dynamics in the NSC RIA regulatory evaluation. This model has an actual RPV geometry and can be simply separated from other influential factors in order to concentrate only on investigation of the fluid viscosity effect. In the second scenario, a two-dimensional axisymmetric reactor vessel model with major ...

Scientific Electronic Library Online (English)

Abstract in english A simplified model for drying solids in the constant rate period in a batch fluidised bed was developed.It assumes the bed to be divided into dense and bubble phases with heat and mass transfer between the phases.The model predicts the constant-rate drying period, provided the fluid bed shape and material characteristics are known.The model is compared with experimental data reported in the literature covering a wide range of materials, gas flow rates, column diameters, m (more) aterial hold-ups, air temperatures and humidities.Model predictions compare satisfactorily with the experimental data.

Energy Technology Data Exchange (ETDEWEB)

The Two-Column Aerosol Project (TCAP) field campaign will provide a detailed set of observations with which to (1) perform radiative and cloud condensation nuclei (CCN) closure studies, (2) evaluate a new retrieval algorithm for aerosol optical depth (AOD) in the presence of clouds using passive remote sensing, (3) extend a previously developed technique to investigate aerosol indirect effects, and (4) evaluate the performance of a detailed regional-scale model and a more parameterized global-scale model in simulating particle activation and AOD associated with the aging of anthropogenic aerosols. To meet these science objectives, the Atmospheric Radiation Measurement (ARM) Climate Research Facility will deploy the ARM Mobile Facility (AMF) and the Mobile Aerosol Observing System (MAOS) on Cape Cod, Massachusetts, for a 12-month period starting in the summer of 2012 in order to quantify aerosol properties, radiation, and cloud characteristics at a location subject ...

Energy Technology Data Exchange (ETDEWEB)

We labelled Lipiodol with yttrium-90 and analysed the biodistribution in rats after intrahepatic arterial injection. An RP-18 column was used to separate {sup 90}Y from strontium-90. {sup 90}Y was retained on the column, which had been pretreated with yttrium-selective extraction reagent, di(2-ethylhexyl) phosphate, while {sup 90}Sr was washed out. A hexadentate nitrogen-donor chelating ligand N,N,N`,N`-tetrakis(2-benzymidazolylmethyl)-1,2-ethanediamine (EDTB) was synthesized by condensation of 1,2-benzenediamine and ethylene diamine tetra-acetic acid (EDTA). Lipiodol was covalently conjugated with EDTB. The final product was obtained by eluting the retained {sup 90}Y from the RP-18 column with EDTB-Lipiodol. Sixteen male rats (Sprague-Dawley) were sacrificed at 1 h, 24 h, 48 h and 72 h (four rats at each time) after injection of approximately 0.1 mCi {sup 90}Y-Lipiodol via the hepatic artery. Samples of liver, spleen, ...

International Nuclear Information System (INIS)

A simple and specific method has been developed for the simultaneous determination of the four major Cinchona alkaloids and their dihydroderivatives and pyridoxine hydrochloride (Vitamin B_6) by high-performance liquid chromatography (HPLC) with fluorescence detection (#lambda#_e_m=420 nm with #lambda#_e_x=330 nm). The chromatographic separation was performed on a Phenomenex Prodigy ODS column (5 #mu#m, 250 mmx3.2 mm i.d.), recommended for basic compounds, under isocratic reversed-phase conditions. The method allowed a good peak shape and an effective resolution of the tested compounds. The extraction of alkaloids from the Cinchona succirubra bark was carried out in mild and fast conditions (ambient temperature, 20 min) by ultrasonication. The procedure showed to be advantageous respect to a reference method, which involved Soxhlet extraction. The results were compared statistically by means of the Student's t-test and the variance ratio F-test; no significant ...

Science.gov (United States)

Dissolved organic substances derived from forest litter are believed to influence the retention and movement of SO{sub 4}{sup 2{minus}} in forest soils. A column study was conducted in which {sup 35}SO{sub 4} was surface applied to a soil and leached with either low-molecular-weight aliphatic acids (AA) or a forest-litter extract. Oxalic, malonic, and succinic acids were used in the concentration range 8.0 {times} 10{sup {minus}3} to 1.0 {times} 10{sup {minus}5} mol L{sup {minus}1}. Movement of {sup 35}SO{sub 4} was determined with column depth, as was the {sup 35}SO{sub 4} activity in the collected leachates. Labeled SO{sub 4} soil movement was found to increase with increasing AA concentration. Leachate {sup 35}SO{sub 4} activity was observed to increase in the order malonic > succinic > oxalic for acid treatments > 1.0 {times} 10{sup {minus}4} mol L{sup {minus}1}. The 1.0 {times} 10{sup {minus}5} mol L{sup {minus}1} acid treatments ...

International Nuclear Information System (INIS)

Full text of publication follows: Slightly over-stoichiometric lithium orthosilicate pebbles have been selected as one optional breeder material for the European Helium Cooled Pebble Bed (HCPB) blanket. This material has been developed in collaboration of Research Center Karlsruhe and the Schott Glass, Mainz. The lithium orthosilicate pebbles are fabricated from lithium hydroxide and silica by a melting and spraying method in a semi-industrial scale facility. Lithium hydroxide was selected as the precursor since enriched lithium hydroxide is commercially available. The lithium orthosilicate pebbles produced by the process contains oxide phases besides orthosilicate, but it was also found that the oxide phases can be decomposed by annealing at high temperatures. The lithium orthosilicate pebbles produced in this way possesses satisfactory pebble characteristics. Therefore, the authors performed out-of-pile annealing tests using the lithium orthosilicate pebbles irradiated in a research ...

Energy Technology Data Exchange (ETDEWEB)

This thesis presents the study of the slowing down process of fast heavy ions inside matter. In the framework of this research, the influence of the target density on the stopping process is investigated. Experiments on the interaction of {sup 48}Ca{sup 6+}-{sup 48}Ca{sup 10+} and {sup 26}Mg{sup 5+} ion beams with initial energies of 11.4 MeV/u and 5.9 MeV/u with solid and gaseous targets have been carried out. A novel diagnostic method, X-ray spectroscopy of K-shell projectile radiation, is used to determine the ion charge state in relation to its velocity during the penetration of fast heavy ions inside the stopping material. A spatially resolved analysis of the projectile and target radiation in solids is achieved for the first time. The application of low-density silica aerogels as stopping media provided a stretching of the ion stopping length by 20 - 100 times in comparison with solid quartz. The Doppler Effect observed on the projectile K-shell spectra is ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the invention is a process for the production of a particularly finely divided, homogeneous transition metal phosphide and transition metal chalcogenide of Daltonian stochiometry by the conversion of at least one powder transition metal or a transition metal alloy with phosphorus or with a chalcogen at raised temperature, which is characterized by the fact that the conversion is carried out in the presence of at least one inert finely divided auxiliary material which is soluble in water and does not sinter together at the reaction temperature, and that the conversion produce removes the auxiliary material. Even relatively small quantities of the auxiliary material are sufficient to ensure rapid and homogeneous conversion of the reaction partners to the reaction product having a large surface. A ratio of 1 part by volume of a mixture of a transition metal and phosphorus or chalcogen to 1 part by volume of finely divided auxiliary material proved particularly suitable ...

Energy Technology Data Exchange (ETDEWEB)

The X-ray diffraction (XRD) and environmental scanning electron microscopy (ESEM) analyses of plasters collected from the courtyard walls of Djehuty's tomb show anhydrite, calcite, dolomite, quartz, alkali feldspars and accessorial amounts of halite and illite. The external outer bed is mainly composed by anhydrite, since the original hydrous phases of gypsum plaster were desiccated during thirty centuries in the dry land environment of the Luxor area, under low relative humidity and high temperatures. The luminescence analyses by thermoluminescence (TL) and cathodoluminescence (CL) demonstrate as one plaster sample (m8), i.e., 95% anhydrite, displays a gigantic TL emission of 33 555 a.u. and a SEM/CL emission of 2319 a.u. maxima peak. The spectra CL also exhibits a 484 nm peak attributable to the classic {sup 4}F{sub 9/2}{yields}{sup 6}H{sub 15/2} transition circa 490 nm of Dy{sup 3+} and a 573 nm emission of Dy{sup 3+} masked in a broad emission band ...

Energy Technology Data Exchange (ETDEWEB)

This report presents the work performed at the Institute of Gas Technology (IGT) during the second program quarter from October 1, 1993 to December 31, 1993, under Department of Energy (DOE) Contract No. DE-AC22-93PC92114. This program has co-ordinated funding for Task 1 from IGT`s Sustaining Membership Program (SMP), while DOE is funding Tasks 2--8. Progress in all tasks are reported. The overall objective of this research project is to develop a catalytic process to convert natural gas to liquid transportation fuels. The process consists of two steps that each utilize catalysts and sulfur containing intermediates: (1) to convert natural gas to CS{sub 2} and (2) to convert CS{sub 2} to gasoline range liquids. Experimental data will be generated to demonstrate the potential of catalysts and the overall process. During this quarter, progress in the following areas has been made. An existing unit at IGT was modified to accommodate the sulfur feedstocks and the higher temperatures ...

International Nuclear Information System (INIS)

This is the final report of a one-year, Laboratory-Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). In an effort to address the problems of long term storage and nuclear waste minimization, zircon has been proposed as a host medium for plutonium and other actinides recovered from dismantled nuclear weapons. The objective of this work is to investigate the feasibility of large scale fabrication of Pu-bearing zircon. Since PuO_2 is thermodynamically less stable than ZrO_2, it is expected that the process parameters determined for synthesizing ZrSiO_4 (zircon) would be applicable to those for PuSiO_4 (Pu-zircon). Furthermore, since the foremost concern in plutonium processing is the potential for contamination release, this work emphasizes the development of process parameters, using zircon first, to anticipate potential material problems in the containment system for reaction mixtures during processing. Stoichiometric mixtures of ZrO_2 and ...

Science.gov (United States)

In the present work, a new kind of myoglobin (Mb)/Au nanoparticles composite film was fabricated on pyrolytic graphite (PG) electrodes. Oppositely charged chitosan (CS) and silica (SiO(2)) nanoparticles were alternately adsorbed on the PG surface by the electrostatic interaction between them, forming {CS/SiO(2)}(5) layer-by-layer films. Mb and HAuCl(4) in solution were then simultaneously loaded into {CS/SiO(2)}(5) films. The loaded Au(III) in the films were electrochemically reduced into Au nanoparticles, forming nanocomposite films, designated as {CS/SiO(2)}(5)-Mb-Au. Various techniques such as cyclic voltammetry (CV), square wave voltammetry (SWV), quartz crystal microbalance (QCM), electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and energy dispersive X-ray (EDX) analysis were used to characterize the films. Compared with {CS/SiO(2)}(5)-Mb films without Au nanoparticles inside, the {CS/SiO(2)}(5)-Mb-Au films exhibited much ...

Energy Technology Data Exchange (ETDEWEB)

The fixed bed pilot plant, the catalyst testing procedure, and the calculations for conversion and selectivities were previously described in the technical progress report covering the period of 3/16/88 to 6/16/88 for Contract DE-AC22-87PC79812. Conversions and hydrocarbon selectivities were calculated using data from an on-line gas chromatography (GC) analyzer. Alcohol selectivities were calculated using data from an on-line boiling point GC analyzer which analyzed the liquid product. The catalysts were prepared via the steps of impregnation, calcination, and reduction on a special Y-zeolite-derived support. The impregnation step consisted of evaporation of metal salts on to the support from an aqueous solution. For one catalyst (No. 6531-188) the metal salts were evaporated on to the support from a reverse micelle solution containing the metal salts. All the catalysts were calcined for four hours at 450{degree}C. The calcined catalysts were loaded in the reactor with a diluent ...

International Nuclear Information System (INIS)

A wide variety of thin film coatings, deposited by different techniques and with potential applications in various important areas, have been characterised by the Phase Modulated Spectroscopic Ellipsometer, installed recently in the Spectroscopy Division, B.A.R.C. The Phase Modulated technique provides a faster and more accurate data acquisition process than the conventional ellipsometry. The measured Ellipsometry spectra are fitted with theoretical spectra generated assuming an appropriate model regarding the sample. The fittings have been done objectively by minimising the squared difference (#chi#"2) between the measured and calculated values of the ellipsometric parameters and thus accurate information have been derived regarding the thickness and optical constants (viz, the refractive index and extinction coefficient) of the different layers, the surface roughness and the inhomogeneities present in the layers. Measurements have been done on (i) ion-implanted Si-wafers to ...

Energy Technology Data Exchange (ETDEWEB)

An analysis is presented of the electron temperature in a linear device which includes the effect of thermal conduction, heat flux limit, radiation, and end plugs. It is found that the thermal conduction and the heat flux limit are dominant in the initial phase of cooling, while the later phase is almost completely controlled by radiation that spatially homogenizes the temperature distribution. In the case of bremsstrahlung, within the frame of the present model, the temperature decays to zero in a finite time. This process takes the form of a cooling wave that moves from the ends of the column to the center. Impurities cause a milder, exponential decay, which is still much faster than the algebraic conduction decay. The thermal effectiveness of the end plugs is described by a convective transfer coefficient h/sub p/. Its scaling law (in terms of the coupled plamsa-plug system) reveals that a very high plug-plasma density ratio provides a simple way to ...

British Library Electronic Table of Contents (United Kingdom)

Abstract We analyse extinction maps of nearby giant molecular clouds to forge a link between driving processes of turbulence and modes of star formation. Our investigation focuses on cloud structure in the column density range above the self-shielding threshold of 1-mag AV and below the star formation threshold - the regime in which turbulence is expected to dominate. We identify clouds with shallow mass distributions as cluster forming. Clouds that form stars in a less clustered or isolated mode show a steeper mass distribution. Structure functions prove inadequate to distinguish between clouds of different star formation mode. They may, however, suggest that the turbulence in the average cloud is governed by solenoidal forcing. The same is found using the -variance analysis which also in...

Energy Technology Data Exchange (ETDEWEB)

Ternary diagrams or pseudo ternary diagrams are commonly used to provide a graphical representation of equilibrium fluid phase behavior for systems as diverse as distillation columns and miscible gas floods of oil reservoirs. The phase envelope and the position of the critical point on it are important to enhanced oil recovery engineers who are involved with miscible gas flood design. In the past, phase equilibrium data were laboriously plotted on the pseudo ternary diagram and special graphical techniques were utilized to locate the critical point on the phase envelope. Presented in this article is a computerized curve fitting method to, firstly, generate the phase envelope from a given set of phase equilibrium data and then use the 'tie-line slopes' to position the critical point. Experimental data are included and show excellent agreement with this new method.

Energy Technology Data Exchange (ETDEWEB)

We have developed a method for the synthesis of C-11 iodoantipyrine. Carbon-11-labeled methyl iodide, prepared from /sup 11/CO2, was used to methylate 3-methyl-1-phenyl-2-pyrazolin-5-one to form C-11 antipyrine. Following silica-gel column chromatography and iodination, radiochemical purity of the C-11 iodoantipyrine was more than 99.5%, with a 10% yield and a specific activity of 30 mCi/mumol. Preliminary animal studies showed complete cerebral extraction and local cerebral blood-flow values that were within 4.6% of those obtained using C-14 iodoantipyrine. The C-11 analog, with positron emission tomography, will facilitate local cerebral blood-flow studies in human subjects.

British Library Electronic Table of Contents (United Kingdom)

Abstract Capillary permeability is a tightly regulated feature of microcirculation in all organ beds. In sepsis, this feature is fundamentally altered. We have previously reported elevated levels of angiopoietin-2 in patients with septic shock, and have investigated tumor necrosis factor (TNF)-related and weak inducer of apoptosis (TWEAK), which mediates both angiogenesis and inflammation, in those patients. Enzyme-linked immunoassay was used to measure serum TWEAK levels in 20 patients with septic shock, all of whom were treated by direct hemoperfusion with a polymyxin B-immobilized fiber column (DHP-PMX), and in 20 non-septic controls. The TWEAK levels were higher in patients with septic shock (192.8--230.5-pg/mL) than in controls (84.1--28.7-pg/mL, P-=-0.043). Between 11 survivors and 1...

DEFF Research Database (Denmark)

We study the spike statistics of neurons in a network with dynamically balanced excitation and inhibition. Our model, intended to represent a generic cortical column, comprises randomly connected excitatory and inhibitory leaky integrate-and-fire neurons, driven by excitatory input from an external population. The high connectivity permits a mean field description in which synaptic currents can be treated as gaussian noise, the mean and autocorrelation function of which are calculated self-consistently from the firing statistics of single model neurons. Within this description, a wide range of Fano factors is possible. We find that the irregularity of spike trains is controlled mainly by the strength of the synapses relative to the difference between the firing threshold and the postfiring reset level of the membrane potential. For moderately strong synapses, we find spike statistics very similar to those observed in primary visual cortex.

International Nuclear Information System (INIS)

Results of ongoing research project at the McMaster Nuclear Reactor Facility on real-time neutron radiography for the visualization of interfacial geometry, movements and phase distributions in gas-liquid and gas-liquid-metal multi-phase flows are presented. Experiments were conducted with bubble column tubes with boiling liquid nitrogen, air-water and air-mercury mixtures. Discussions are also focused on air-water flowing within a tube containing a CANDU type 37 rod fuel bundle assembly positioned both horizontally and vertically. Computer processing using a digital image format to enhance the real-time images was used. Imaging techniques include frame averaging, background substraction, edge enhancement (spatial filtering), contrast enhancement and video densitometry. (orig.).

British Library Electronic Table of Contents (United Kingdom)

In order to investigate the antioxidant properties of the polysaccharides from the brown alga Sargassum fusiforme, the crude polysaccharides from S. fusiforme (SFPS) were extracted in hot water, and the lipid peroxidation inhibition assay exhibited that SFPS possessed a potential antioxidant activity. Hence, two purely polymeric fractions, SFPS-1 and SFPS-2 were isolated by the column of DEAE (2-diethylaminoethanol)-Sepharose Fast Flow, with their molecular weights of 51.4 and 30.3 kDa determined by high performance gel permeation chromatography (HPGPC). They were preliminarily characterized using chemical analysis in combination of infrared (IR) and nuclear magnetic resonance (NMR) spectroscopies and found to contain large amounts of uronic acids and ?-glycosidical linkages. The antioxida...

Energy Technology Data Exchange (ETDEWEB)

Optimum plant operation can often be achieved by means of constraint control instead of model- based on-line optimization. This is because optimum operation is seldom at the top of the hill but usually at the intersection of constraints. This article describes the development of a constraint control system for a plant producing ethylbenzene (EB) by the Mobil/Badger Ethylbenzene Process. Plant optimization can be defined as the maximization of a profit function describing the economics of the plant. This function contains terms with product values, feedstock prices and operational costs. Maximization of the profit function can be obtained by varying relevant degrees of freedom in the plant, such as a column operating pressure or a reactor temperature. These degrees of freedom can be varied within the available operating margins of the plant.

Energy Technology Data Exchange (ETDEWEB)

Water vapor is well known to be a critical component in many aspects of atmospheric research, such as radiative transfer and cloud and aerosol processes. This requires both improved measurements of the columnar water vapor and its profiles in the atmosphere in a wide range of conditions, and adjustment of water vapor parameterizations in radiation codes including the perfection of spectroscopic parameters. In this paper we will present the results of comparison of our calculations and downward solar fluxes measured with Rotating Shadowband Spectroradiometer under conditions of horizontally homogeneous clouds. We also will discuss the sensitivity of atmospheric radiation characteristics to variations of water vapor in the band 940 nm: these results may be useful for development of new methods of retrieval of the total column water vapor content (WVC) in the atmosphere from data of radiation observations.

British Library Electronic Table of Contents (United Kingdom)

A microcosm laboratory experiment was conducted to determine the impact of biological reworking by the ragworm Nereis diversicolor on the redistribution of particle-bound radionuclides deposited at the sediment-water interface. Over the course of the 40-day experiment, as much as 35% of a 137Cs-labelled particulate tracer deposited on the sediment surface was redistributed to depths of up to 11 cm by the polychaete. Three different reworking models were employed to model the profiles and quantify the biodiffusion and biotransport coefficients: a gallery-diffuser model, a continuous sub-surface egestion model and a biodiffusion model. Although the biodiffusion coefficients obtained for each model were quite similar, the continuous sub-surface egestion model provided the best fit to the data...

International Nuclear Information System (INIS)

A successful boron neutron capture treatment (BNCT) of a patient with multiple liver metastases has been first given in Italy, by placing the removed organ into the thermal neutron column of the Triga research reactor of the University of Pavia. In Finland, FiR 1 Triga reactor with an epithermal neutron beam well suited for BNCT has been extensively used to irradiate patients with brain tumors such as glioblastoma and recently also head and neck tumors. In this work we have studied by MCNP Monte Carlo simulations, whether it would be beneficial to treat an isolated liver with epithermal neutrons instead of thermal ones. The results show, that the epithermal field penetrates deeper into the liver and creates a build-up distribution of the boron dose. Our results strongly encourage further studying of irradiation arrangement of an isolated liver with epithermal neutron fields.

Energy Technology Data Exchange (ETDEWEB)

The energy available from tidal currents is substantial and considerable work has been conducted into determining the size of the resource and what the large-scale consequences of extraction might be. This paper describes the work conducted to establish a laboratory-scale model, by using the commercial computational fluid dynamics (CFD) code FLUENT trademark, in order to predict local-flow consequences resulting from the extraction of energy in two and three dimensions from within the water column in a tidal flow. As might be expected, a wake is formed but there is considerable localized flow acceleration around and, most especially, under an extraction zone. The wake behind the device is shown to be associated with a drop in the free surface which, in turn, is associated with the decline in the wake itself. (author)

International Nuclear Information System (INIS)

Using electrochemical techniques of pH-metry and conductimetry, the choice of a suitable complexing reagent was made amongst ethylene glycol, propylene glycol, dextrose and mannitol for cost-effective separation of isotopes of boron by ion exchange chromatography. Quantitative relationships between pH and concentration; pK_a and concentration of each of these complexing reagents were determined by least square polynomial curve fitting and an attempt was made to determine the formation constants of mannitol-borate complex. The results of experiments carried out for selection; regeneration of a resin; separation factor determinations using batch as well as column techniques and monitoring of band movements using these electrochemical techniques are discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

0pen ended piles develop internal frictional resistance between the internal soil plug end the pile wall during axial loading. Current pipe pile design practice assumes that the ultimate internal skin friction is of the same order of magnitude as the outer skin friction. This paper describes a series of laboratory pile load tests on instrumented model pipe piles, designed to investigate the development of plug stresses and skin friction along the plug length during pile loading. The piles contain sand columns of various relative densities and of different heights. The soil plugs are loaded to failure under fully drained conditions. The test data indicate that internal skin friction in sand can be substantially higher than assumed in conventional design practice. This finding could lead to significant economical savings on future pipe pile foundations in sand.

International Nuclear Information System (INIS)

Gamma-ray spectrometric analysis was employed to determine the nuclides formed in thorium by neutron irradiation. Thorium sample was irradiated by neutron from a pure thermal neutron field, neutron field of Cd ratio of about 4, and epithermal neutron field, respectively. The former irradiation was carried out in a thermal neutron column provided for medical uses of neutrons, and the latters were done in the F-ring position of TRIGA II research reactor of Musashi Institute of Technology. The gamma-ray spectra were obtained and analyzed by employing a fully automatic gamma-ray analysis system named ''GAMA: giant frog:-SYSTEM'' developped by Musashi Institute of Technology. The formation of Pa-233 (U-233) was discussed quantitatively with respect to the difference of the neutron field. (author).

Energy Technology Data Exchange (ETDEWEB)

The US NRC, in its Generic Environmental Impact Statement on uranium milling has specified that the radon flux escaping a uranium mill tailings pile will be reduced to pCi/m/sup 2/ s by application of covering layers of soils and clays. These covers present a radon diffusion barrier, which sufficiently increases the time required for radon passage from the tailings to the atmosphere to allow for decay of /sup 222/Rn within the cover. The depth of cover necessary to reduce the escaping radon flux to the prescribed level is to be determined by calculation, and requires precise knowledge of the radon diffusion coefficient in the covering media. A Radon Attenuation Test Facility was developed to determine rates of radon diffusion through candidate cover materials. This paper describes this facility and its application for determining the influence of physical properties of the soil column on the radon diffusion coefficient.

British Library Electronic Table of Contents (United Kingdom)

Phenytoin (PHT), phenobarbital (PHB), lamotrigine (LTG), and topiramate (TPM) are some of the most widely used antiepileptic drugs (AEDs). Monitoring of their concentrations in serum is important for the treatment of epilepsy. A reference measurement procedure (RMP) for certification of PHT, PHB, LTG, and TPM in serum has been developed and critically evaluated. Isotopically labeled compounds of PHT, PHB, LTG, and TPM are used as internal standards for the four AEDs. The four drugs and their respective labeled internal standards are simultaneously extracted from serum using solid-phase extraction prior to reversed-phase liquid chromatography?tandem mass spectrometry (LC-MS/MS). Chromatographic separation was performed using a C18 column. Electrospray ionization (ESI) in the positive ion mo...

Energy Technology Data Exchange (ETDEWEB)

Conditions of the separation and detection of organic and inorganic anions by gradient ion chromatography and suppressed conductivity detection were studied, and the procedure of gradient elution was optimized. A detection limit of 1 x 10{sup -3} {mu}g x L{sup -1} was obtained using the pre-concentrated column and most relative standard deviations obtained in the determination of seven organic and inorganic anions were below 5%. This method was proved to be simple, rapid and accurate for the separation and determination of low-molecular-weight organic acids and inorganic anions and could be applied in the analysis of the samples from water and steam systems of thermal power plants with satisfactory results. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Concentrations of {sup 239+240} Pu and {sup 137} Cs were measured for vertical direction and horizontal direction in seawater collected at 21 locations on the 8 directions near Wolsung nuclear power plant. The inventories of {sup 239+240} Pu and {sup 137} Cs were calculated in seawater column. The concentrations of {sup 239+240} Pu and {sup 137} Cs were in seawater in the range of 8-36 {mu}Bq/L, 2.4-4.5 mBq/L, respectively. The {sup 239+240} Pu concentration increased with depth, however, the {sup 137} Cs concentrations not greatly changed with depth above thermocline.

Energy Technology Data Exchange (ETDEWEB)

Radioactively contaminated acidic aqueous wastes and organic liquids were discharged to the soil column at three disposal sites within the 200 West Area of the Hanford Site, Washington. As a result, a portion of the underlying groundwater is contaminated with carbon tetrachloride several orders of magnitude above the maximum contaminant level accepted for a drinking water supply. Treatability testing and cleanup actions have been initiated to remove the contamination from both the unsaturated soils to minimize further groundwater contamination and the groundwater itself. To expedite cleanup, innovative technologies for (1) drilling, (2) site characterization, (3) monitoring, (4) well field development, and (5) contaminant treatment are being demonstrated and subsequently used where possible to improve the rates and cost savings associated with the removal of carbon tetrachloride from the soils and groundwater.

Energy Technology Data Exchange (ETDEWEB)

Measurements of local mass fluxes of liquid, local number fluxes of the drop and local drop size distributions at various locations in the test column were made for wide ranges of liquid flow rates and gas flow rates. An empirical correlation for the volume mean diameter of the drop at the nozzle exit was proposed. Measurements of the rates of absorption of carbon dioxide from carbon dioxide-air mixtures with water sprays (physical absorption) and aqueous sodium hydroxide sprays (chemical absorption) were made for wide range so fluid flow rates, feed gas concentrations, and initial alkali concentrations. The observed dimensionless rates of absorption were compared with the theoretical values by assuming penetration model with second-order irreversible reaction. 11 refs., 7 figs.

British Library Electronic Table of Contents (United Kingdom)

In this study, bacterial strains were investigated in order to determine their heavy metal tolerance. The bacterial strains were identified as Bacillus cereus and Bacillus pumilus. In the batch system, the effects of operating variables such as solution pH, initial metal concentration, contact time, and adsorbent dosage were investigated. Both isolates were highly resistance to copper and lead in comparison with the control strain examined. The adsorption capacities of B. cereus and B. pumilus were found to be 22.1mg/g and 28.06mg/g, respectively. The biosorption follows pseudo-second order kinetics and the isotherm fits well to the Langmuir isotherm model. In column experiments, the biosorption was fitted well by the Thomas model. The breakthrough and exhaustion capacity of each biosorben...

British Library Electronic Table of Contents (United Kingdom)

Teleost gut associated lymphoid tissue (GALT) consists of leucocyte populations located both intraepithelially and in the lamina propria with no structural organization. The present study aims to assess different protocols for the isolation of GALT cells from an important fish species in the Mediterranean aquaculture, the gilthead seabream. Mechanical, chemical and enzymatic treatments were assayed. Nylon wool columns and continuous density gradients were used for further separation of cell subpopulations. Light microscopy and flow cytometry showed that the highest density band (HD) consisted of a homogeneous lymphocytic population, whereas the intermediate density band (ID) corresponded to epithelial and secretory cells and some lymphocytes. Respiratory burst activity of total cell suspen...

British Library Electronic Table of Contents (United Kingdom)

This study investigated the optimum polyphenol extraction conditions for two Nigerian green leafy vegetables, Vernonia amygdalina (VA) and Gongronema latifolium (GL) that are widely used for food and medicinal purposes. Seven different solvents were used to extract the total phenolic contents of the leaves; 100% acetone, 80% acetone, 50% acetone, 100% ethanol, 70% ethanol, 100% methanol and 70% methanol and their total phenolic contents were determined. The results showed that the 80% acetone was significantly (p<0.05) the most effective for polyphenol extraction from the leaves and generally the acetone-containing solvents were more effective than alcohol-containing solvents. The 80% acetone extract was fractionated on a silicic acid-packed column to give two main fractions: acetone elute...

Energy Technology Data Exchange (ETDEWEB)

Anion-exchange chromatography of element 105, dubnium (Db), produced in the {sup 248}Cm({sup 19}F, 5n){sup 262}Db reaction is investigated together with the homologues Nb and Ta, and the pseudo-homologue Pa in 13.9 M hydrofluoric acid (HF) solution. The distribution coefficient (K{sub d}) of Db on an anion-exchange resin is successfully determined by running cycles of 1702 chromatographic column separations. The result clearly indicates that the adsorption of Db on the resin is significantly different from that of the homologues and that the adsorption of anionic fluoro complexes of these elements decreases in the sequence of Ta{approx}Nb>Db{>=}Pa. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The developed system is intended for use at a collimated thermal neutron beam with a flux of about 10{sup 6} n/cm{sup 2} s. The system works with a cooled CCD array (192 x 165 pixels) and an intensifier for light from a NE426 scintillator with traditional optical coupling. A fine mechanical regulation system allows an accurate positioning of the tomographer, also ensuring the alignment of the CCD array with the rotation and translation axes. The acquisition of 200 projections is carried out in about 30 min with a reconstruction time (40 min max) depending on the reconstruction-matrix order. Radiography and tomography of significant objects are illustrated. The reconstruction algorithm, including spatial and temporal inhomogeneity corrections and filters, was tested with good results for projections up to 512 x 512 pixels. (orig.)

Science.gov (United States)

The purpose of this column is to present the results of the 2007 Professional Practice Analysis (PPA) of the field of nurse anesthesia, conducted by the Council on Certification of Nurse Anesthetists. The PPA used survey and rating scale methodologies to collect data regarding the relative emphasis of various aspects of the nurse anesthesia knowledge domain and competencies. A total of 3,805 survey responses were analyzed using the Rasch rating scale model, which aggregates and transforms ordinal (rating scale) responses into linear measures of relative importance and frequency. Summaries of respondent demographics and educational and professional background are provided, as well as descriptions of how the survey results are used to develop test specifications. The results of this analysis provide evidence for the content outline and test specifications (content percentages) and thus serve as a basis of content validation for the National Certification Examination. ...

Energy Technology Data Exchange (ETDEWEB)

A method for product analysis that eliminates a problematic step in the radiometric sucrose-phosphate synthase assay is described. The method uses chromatography on a boronate-derivatized high-performance liquid chromatography column to separate the labeled product, (14C)sucrose phosphate, from unreacted uridine 5{prime}-diphosphate-(14C)glucose (UDP-Glc). Direct separation of these compounds eliminates the need for treatment of the reaction mixtures with alkaline phosphatase, thereby avoiding the problem of high background caused by contaminating phosphodiesterase activity in alkaline phosphatase preparations. The method presented in this paper can be applied to many UDP-Glc requiring enzymes; here the authors show its use for determining the activities of sucrose-phosphate synthase, sucrose synthase, and uridine diphosphate-glucose pyrophosphorylase in plant extracts.

Energy Technology Data Exchange (ETDEWEB)

This Waste Management Plant (WMP) for the Bear Creek Valley Treatability Study addresses waste management requirements for the Oak Ridge Y-12 Plant. The study is intended to produce treatment performance data required to design a treatment system for contaminated groundwater. The treatability study will consist of an evaluation of various treatment media including: continuous column tests, with up to six columns being employed to evaluate the performance of different media in the treatment of groundwater; an evaluation of the denitrifying capacity and metal uptake capacity of a wetland system; and the long-term denitrifying capacity and metal uptake capacity of algal mats. The Sampling and Analysis Plan (SAP) covers the project description, technical objectives, procedures, and planned work activities in greater detail. The Health and Safety Plan (HASP) addresses the health and safety concerns and requirements for the proposed sampling ...

International Nuclear Information System (INIS)

The interaction of Np(V), Pu(VI) and Tc(VII) with metal reductants Zn, Cr, Sn and their alloys was investigated in 0.5-4 mol l"-"1 NaOH solutions in static and dynamic conditions (by filtration of solutions through the column filled with grains of metal). In this paper, it was found that the reduction and succeeding precipitation hydroxides of these elements, on the surface of metal grains from 0.5 to 4 mol l"-"1 NaOH solutions, gives a decontamination factor (DF) from 1.1 to 67. The best result was achieved for Pu (DF=67) on Cr grains after 2.5 h contact at 60 C with 0.5 mol l"-"1 NaOH solution containing Pu(VI). Increasing the NaOH concentration, and the addition of chromate ions and complex-forming agents to alkaline solution results in a decrease of the decontamination factor (DF). A better result for Np sorption from 1 mol l"-"1 NaOH solutions was achieved after longer contact, than for Pu, with Cr and Zn grains. The maximum DF=8.9 was achieved for Tc on a ...

Energy Technology Data Exchange (ETDEWEB)

The design of separation devices, particularly for solvent-based selective removal of H{sub 2}S from CO{sub 2}, requires an accurate mathematical model. Unfortunately, this requirement for high accuracy is often in conflict with the need for efficient computation. The addition of more and more complicated analyses, such as a move from Henry's law to a method incorporating gas and liquid activities for computing vapor liquid equilibria, may give a more accurate solution, but only at the cost of decreased computational efficiency. The efforts in this work have been directed toward two goals. The first was to develop an accurate mathematical model for the aqueous methyldiethanolamine (MDEA) system. The steady-state packed column model developed in this work has been tested with data from Schubert (1988) to verify its accuracy. The second goal was to modify the model to improve its computational efficiency. Areas such as vapor-liquid equilibrium calculations, ...

International Nuclear Information System (INIS)

Gadolinium removal during the first approach to criticality of TAPP-4 540 MWe reactor using mixed bed resin (strong acid cation resin and weak base anion resin) topped with strong acid cation exchange resin yielded IX column outlet pH of >6 during the first 6 h of run during which [Gd] decreased from 2.1 to 1 mg/kg. However, the main moderator system pH was between 5.0-5.5. Technical specification for pH of moderator is in the range 5.0-5.5 as long as Gd is present. This is to avoid any precipitation of Gd in the core and a pH of 5.8 or even a pH of 5.6 when carbonate is present is specified as the upper limit of the moderator system pH for this purpose. The situation of IX column outlet pH being #>=# 6 mixing with a system water having Gd results in local mixing zone pH in the range of 6- 5.4. In order to have an iso-pH regime (5-5.5) both with respect to the IX outlet as well as in the system, studies were conducted to modify IX resin ...

Energy Technology Data Exchange (ETDEWEB)

Three reactive materials were evaluated at laboratory scale to identify the optimum treatment reagent for use in a Permeable Reactive Barrier Treatment System at Rocky Flats Environmental Technology Site (RFETS). The contaminants of concern (COCS) are uranium, TCE, PCE, carbon tetrachloride, americium, and vinyl chloride. The three reactive media evaluated included high carbon steel iron filings, an iron-silica alloy in the form of a foam aggregate, and a peculiar humic acid based sorbent (Humasorb from Arctech) mixed with sand. Each material was tested in the laboratory at column scale using simulated site water. All three materials showed promise for the 903 Mound Site however, the iron filings were determined to be the least expensive media. In order to validate the laboratory results, the iron filings were further tested at a pilot scale (field columns) using actual site water. Pilot test results were similar to laboratory results; ...

Energy Technology Data Exchange (ETDEWEB)

While tritium exposure to the site-workers in Wolsung NPP is upto about 40 % of the total personnel exposure, Korea Institute of Nuclear Safety has asked tritium removal facility, as one of the requirements for post reactor construction, after operation of four CANDU reactors in Wolsung site. For the purpose of essential removal of tritium from the heavy water system of the heavy water reactors, an experiment of Ar-N{sub 2} cryogenic distillation tower was carried out as a preliminary study for development of liquid-phase catalytic exchange - cryogenic hydrogen distillation process. The steady-state reached after 50 minutes under 90 K in the Ar-N{sub 2} distillation column (inner diameter 20 mm, height 500 mm) packed with Dixon ring ({phi} 3 mm x H 3 mm), and the ratios of Ar-concentration at the top and at the bottom measured by gas chromatography within {+-}1 % relative error was approximately 93 : 3. This value was distillation performances quite higher than ...

International Nuclear Information System (INIS)

The core bypass flow in a prismatic very high temperature reactor (VHTR) is an important design consideration and can have considerable impact on the condition of reactor core internals including fuels. The interstitial gaps are an inherent presence in the reactor core because of tolerances in manufacturing the blocks and the inexact nature of their installation. Furthermore, the geometry of the graphite blocks changes over the lifetime of the reactor because of thermal expansion and irradiation damage. The occurrence of hot spots in the core and lower plenum and hot streaking in the lower plenum (regions of very hot gas flow) are affected by bypass flow. In the present study, three-dimensional computational fluid dynamic (CFD) calculations of a typical prismatic VHTR are conducted to better understand bypass flow phenomena and establish an evaluation method for the reactor core using the commercial CFD code FLUENT. Parametric calculations changing several factors in a one-twelfth ...

Energy Technology Data Exchange (ETDEWEB)

Piper regnellii (Miq.) C. DC. var. pallescens (C. DC.) Yunck (Piperaceae) is a medicinal plant traditionally used in Brazil to treat infectious diseases. The extracts obtained from the leaves of P. regnellii were investigated for their antifungal activities against the yeasts Candida albicans, C. krusei, C. parapsilosis, and C. tropicalis. The EtOAc extract presented gnificant activity against Candida albicans with MIC at 125 {mu}g mL{sup -1}, and a moderate activity against both C. krusei and C. parapsilosis with MIC at 500 {mu}g mL{sup -1}. Candida tropicalis was not inhibited by this extract at concentrations as high as 1000 {mu}g mL{sup -1}. Based on these findings, the EtOAc extract was fractionated by silica gel column chromatography into nine fractions. The hexane and CHCl{sub 3} fractions showed varied levels of antifungal activity against all test yeasts. Further column chromatography separation of the hexane fraction afforded the pure ...

Energy Technology Data Exchange (ETDEWEB)

LEDF(Large Equipment Dismantling Facility) is the solid waste processing technology development facility that carries out high-volume reduction and low dosage processing. The high-volume reduction processing of the high dose {alpha}-waste configured with combustible waste, pvc and rubber, spent ion exchange resin, and noncombustible waste have been planned the incinerating and melting facility using the in-can type high frequency induction heating in LEDF. This test is intended to clarify the design data. It was confirmed that the incinerating and melting performance, molten solid properties and exhaust gas processing performance with pilot testing equipment and bench scale equipment. The result of this test are as follows. 1. Processing speed is 6.7 kg/h for the combustible waste, 13.0 kg/h for the ion exchange resin, and 30.0 kg/h for the noncombustible waste. For above optimum processing conditions are as follows. Operating temperature is 1000degC for the combustible waste, 1300degC ...

International Nuclear Information System (INIS)

Full text: Dissolution test (DT) is one of the important specifications of PFBR MOX fuel. It is a macro homogeneity test used to ascertain that the dissolution of spent fuel will be easier during reprocessing. The DT specification limit for PFBR MOX fuel is ? 1.0 wt.% residue of the whole pellet when it is dissolved in HNO3 under reflux conditions. For this test, sintered MOX pellet is dissolved in reflux condition in 60 ml of 12M HNO3 for 10 hours. This test is carried out for each batch and during complete MOX campaign a lot of MOX waste in liquid form is being generated. This liquid waste is in clean form and U and Pu is required to be recovered from the clean waste. Different methods like direct denitration, precipitation and solvent extraction are available but either the product is not of good quality for pelletization or secondary liquid wastes are generated. Microwave denitration is a faster and cleaner method which has different heat transfer mechanism and temperature profile ...

Energy Technology Data Exchange (ETDEWEB)

An x-ray zone plate was fabricated using the novel approach of focused ion beam (FIB) milling. The FIB technique was developed in recent years, it has been successfully used for transmission electron microscopy (TEM) sample preparation, lithographic mask repair, and failure analysis of semiconductor devices. During FIB milling, material is removed by the physical sputtering action of ion bombardment. The sputter yield is high enough to remove a substantial amount of material, therefore FIB can perform a direct patterning with submicron accuracy. The authors succeeded in fabricating an x-ray phase zone plate using the Micrion 9500HT FIB station, which has a 50 kV Ga{sup +} column. Circular Fresnel zones were milled in a 1.0-{micro}m-thick TaSiN film deposited on a silicon wafer. The outermost zone width of the zone plate is 170 nm at a radius of 60 {micro}m. An achieved aspect ratio was 6:1.

CERN Document Server

The problem of model selection arises in a number of contexts, such as subset selection in linear regression, estimation of structures in graphical models, and signal denoising. This paper generalizes the notion of "incoherence" in the existing literature on model selection and introduces two fundamental measures of coherence---termed as the worst-case coherence and the average coherence---among the columns of a design matrix. It utilizes these two measures of coherence to provide an in-depth analysis of two variants of a simple one-step thresholding (OST) algorithm for model selection and proves that OST is feasible for model selection as long as the design matrix obeys an easily verifiable property. One of the key insights offered by the ensuing analysis in this regard is that if the design matrix has reasonably small worst-case and average coherence then OST performs near-optimally when either (i) the energy of any nonzero entry of the signal is close to the ...

Energy Technology Data Exchange (ETDEWEB)

Known trace-matrix-separation and enrichment procedures for the refractory metals Mo and W use very time-consuming batch-techniques. This paper presents the application of a quasicontinuous liquid chromatographic (LC) technique as a step towards automated ultratrace separation. The anionic peroxo complexes from Mo(VI) and W(VI) are used for the trace-matrix-separation. Optimization of the peroxide concentration permits a complete removal of all cationic analyte traces on the HPLC-suitable cation exchanger Nucleosil SA. The high chromato-graphic efficiency also allows a direct ion chromatographic separation of the removed traces. This leads to conclusions about the contribution of the analyte traces on the trace-matrix-separation column and the limits of determination. (author). 13 refs.; 12 figs.; 5 tabs.

British Library Electronic Table of Contents (United Kingdom)

The A2P-X2+Dv=-3 bands of the 12C14N radical have been observed by time-resolved Fourier transform spectroscopy in the 1850-3100cm-1 region with a wavenumber resolution of 0.025cm-1. The radical was produced in a pulsed positive column discharge in a cyanogene and helium mixture. Seven bands of v=0-3, 1-4, 2-5, 3-6, 4-7, 5-8, and 6-9 were analyzed to give the molecular constants of each state by least-squares fitting of 801 lines. The pulsed discharge was found to be efficient for production of CN in the excited A2P state. The vibrational excitation temperature was determined to be 6680+-835K and 6757+-534K for the A2P and X2+ states, respectively. The population of the A2P was found to be 4% of that of the X2+ state in the time after turning off the discharge.

International Nuclear Information System (INIS)

Tripartite efflux systems are responsible for the export of toxins across both the inner and outer membranes of Gram negative bacteria. Previous work has indicated that EmrAB-TolC from Escherichia coli is such a tripartite system, comprised of EmrB an MFS transporter, EmrA, a membrane fusion protein and TolC, an outer membrane channel. The whole complex is predicted to form a continuous channel allowing direct export from the cytoplasm to the exterior of the cell. Little is known, however, about the interactions between the individual components of this system. Reconstitution of EmrA + EmrB resulted in co-elution of the two proteins from a gel filtration column indicating formation of the EmrAB complex. Electron microscopic single particle analysis of the reconstituted EmrAB complex revealed the presence of particles approximately 240 x 140 A, likely to correspond to two EmrAB dimers in a back-to-back arrangement, suggesting the dimeric EmrAB form is the ...

International Nuclear Information System (INIS)

Biaxially textured tungsten nanorods (A15 crystal structure) have been grown by oblique angle DC magnetron sputtering using a novel rotation mode called 'two-step rotation'. In this mode, the substrate is given a fast rotation through 1800 at 90 rpm and this is followed by a rest period of 30 s. These nanorods are vertically aligned and have a [100] texture normal to the substrate along with preferential in-plane texture as shown by x-ray pole figure analysis. In contrast, the tungsten nanorods obtained without substrate rotation are slanted at an angle of ?450 and have a [100] texture tilted 160 with respect to the substrate normal. The flux is incident from two diametrically opposite points on the sample at an oblique angle, averaging out the growth into vertical columns that retain the in-plane texture. Scanning electron microscopy shows that the tungsten nanorods have a mixture of {211} and {421} crystal habits; these planes are both minimum surface energy ...

CERN Document Server

We study the structure of the medium surrounding sites of high-mass star formation to determine the interrelation between the HII regions and the environment from which they were formed. The density distribution of the surroundings is key in determining how the radiation of the newly formed stars interacts with the surrounds in a way that allows it to be used as a star formation tracer. We present new Herschel/SPIRE 250, 350 and 500 mum data of LHA 120-N44 and LHA 120-N63 in the LMC. We construct average spectral energy distributions (SEDs) for annuli centered on the IR bright part of the star formation sites. The annuli cover ~10-~100 pc. We use a phenomenological dust model to fit these SEDs to derive the dust column densities, characterise the incident radiation field and the abundance of polycyclic aromatic hydrocarbon molecules. We see a factor 5 decrease in the radiation field energy density as a function of radial distance around N63. N44 does not show a ...

International Nuclear Information System (INIS)

The TS-1 and TS-2 TREAT transient experiments subjected a low burnup (2 MWd/kg) and a medium burnup (58 MWd/kg), respectively, FFTF irradiated fuel pin to unprotected 5 cents/s overpower transient conditions. The fuel pin failure response was similar in the two tests, which demonstrated a large margin to failure (P/P_0 > 3) and a favorable upper level failure location. Thus, for these transient conditions, burnup effects on transient performance appeared to be minimal in the range tested. Pin disruption in the medium burnup TS-2 test was more severe due to the higher fission gas pressurization, but failure occurred at only a 5% lower power level than for the low burnup TS-1 fuel pin. Both tests exhibited axial extrusion of molten fuel to the region above the fuel column several seconds before pin failure, demonstrating a potentially beneficial inherent safety mechanism to delay failure and mitigate accident consequences.

International Nuclear Information System (INIS)

In this paper the structural and functional changes of gamma irradiated bovine hemoglobin are presented. Aqueous solutions/1%/of HbO_2 were irradiated in air with doses ranging from 1 to 4 Mrad. Isoelectric focusing indicated change of the charge of irradiated hemoglobin. The isoelectric point of hemoglobin was displaced towards more acid values with increasing doses, up from 1 Mrad. Fingerprint analysis and peptide column chromatography of irradiated hemoglobin demonstrated disturbances increasing with the dose. These changes were confirmed by amino acid analysis which showed that Cys, Met, Trp, His, Pro and Tyr residues were destroyed or modified following irradiation. At doses exceeding 1 Mrad the irradiated solutions of hemoglobin showed a decrease of heme-heme interaction and an increase of affinity for oxygen. Differences observed in oxygen-dissociation curves seem to be correlated with the radiation induced destruction of amino acid residues which are ...

Energy Technology Data Exchange (ETDEWEB)

Cryogenic distillation is the main industrial method for separating hydrogen's isotopes, because it presents the advantage of high separating factors and also the possibility of processing great quantities of gases. In the case of multicomponent mixtures the determination of transport for molecular species between the two phases is very difficult owing to the particularities of physical characteristics of each component from the mixture. The transport of molecular species is also strongly influenced by the hydrodynamics of two phases, in strong connection with the dimension of the interface between the vapor and liquid phase. The characteristics of the interface depend on the type and geometry of the separation area: plates or package. The traditional methods of analysis for exchange processes use the concept 'theoretic plate', a physical entity for which the values of concentrations for vapors and liquid that leaves the plate are in thermodynamic equilibrium ...

International Nuclear Information System (INIS)

The performance of larger than bench scale ion exchange systems is evaluated by using solutions containing trace amounts of "1"3"7Cs, "8"5Kr, and "1"3"1I, and large amounts of either NaCl or Na_2HPO_4, H_3BO_3, and LiOH. The significant finding in this study is that the empirical rules of ionic selectivity of strong acid cation and strong base anion resins were followed by all ionic species, even though concentrations of some macrocomponents were nearly 10"6 times those of trace components. Other results of possible importance are the correlation between the instantaneous decontamination factor (DF) and the efficiency of column exchange capacity utilization, and the concept of time average decontamination factor (anti DF). The plot of anti DF vs. feed throughput will serve as a guide in determining when the feed should be discontinued in order to achieve a desired anti DF. Both of these correlations are derived from the breakthrough curves.

Energy Technology Data Exchange (ETDEWEB)

The results of the laboratory studies performed by CIEMAT with the FEBEX bentonite in the context of WP3.2 of the NF-PRO Project and of the Agreement ENRESA-CIEMAT Anexo V are presented and analysed in this report. They refer to the effect of the hydraulic gradient on the permeability of bentonite, the effect of the thermal gradient on the hydration kinetics of bentonite, and the repercussion of temperature on the hydro-mechanical properties of bentonite (swelling, permeability and water retention capacity). In all the cases the bentonite has been used compacted to densities expected in the engineered barrier of a high-level radioactive waste repository. The existence of threshold and critical hydraulic gradients has been observed, both of them dependent on bentonite density and water pressures. After more than seven years of hydration, the 40-cm high bentonite columns are far from full saturation, the thermal gradient additionally delaying the process, which is ...

Energy Technology Data Exchange (ETDEWEB)

A characteristic trait of Francis turbines operating at low-head is pressure pulsations that occur during certain load levels of the generator. These stem from pressure variations across the turbine due to pulsating flow in the draft-tube. This surging action of the water column is related to draft-tube geometry and flow-rate of water in the penstock. The pressure pulsations cause torque variations on the turbine and corresponding electric power pulsations. If electric power is used as a feedback signal to the Power System Stabilizer (PSS), then Mvar and terminal voltage pulsations will occur when the generator is operating in the ``rough zone``. This paper describes field test results for investigating feedforward control from the penstock, draft tube and spiral case pressure to reduce the effects of Mw pulsations on PSS output signals. This investigation involved a PSS with generator power as the feedback signal and the PSS tuned for local and inter-area damping.

International Nuclear Information System (INIS)

A Real-Time Neutron Radiography (RTNR) system and a high speed X-ray Computed Tomography (X-CT) system are used to determine the flow regime, the instantaneous cross-sectional averaged void fraction, and the time averaged void fraction in a vertical annulus flow channel. A standard optical video system is also used to observe the flow regime. The annulus flow channel is operated as a bubble column and measurements are obtained for gas flow rates form 0.0 to 30.0 l/min. The flow regimes observed by all three measurement systems via image analysis shows that the results agree well with each other. Both the RTNR and the X-CT systems show that the time averaged and cross-sectional averaged void fraction increases with increasing superficial gas velocity. Time and cross-sectional averaged void fractions determined by the RTNR system agree within 4% with those determined by the high speed X-ray CT technique. (orig.).

Energy Technology Data Exchange (ETDEWEB)

RADIANT{trademark} is manufactured by United States Surgical Corporation, Vascular Therapies Division, (formerly Progressive Angioplasty Systems). The system comprises a liquid {beta}-radiation source, a shielded isolation/transfer device (ISAT), modified over-the-wire or rapid exchange delivery balloons, and accessory kits. The liquid {beta}-source is Rhenium-188 in the form of sodium perrhenate (NaReO{sub 4}), Rhenium-188 is primarily a {beta}-emitter with a physical half-life of 17.0 hours. The maximum energy of the {beta}-particles is 2.1 MeV. The source is produced daily in the nuclear pharmacy hot lab by eluting a Tungsten-188/Rhenium-188 generator manufactured by Oak Ridge National Laboratory (ORNL). Using anion exchange columns and Millipore filters the effluent is concentrated to approximately 100 mCi/ml, calibrated, and loaded into the (ISAT) which is subsequently transported to the cardiac catheterization laboratory. The delivery catheters are modified ...

Energy Technology Data Exchange (ETDEWEB)

In the framework of the feasibility study of radioactive waste disposal in deep geologic formations, a clay formation (named 'argilite de l'Est') has been selected in the Meuse-Haute Marne region (France) for the construction of an underground laboratory. The percolation of alkaline solutions through the argilite has been studied using column experiments with short residence times (30 min). These experiments simulate the leaching of a cement which could be used in the building materials of the laboratory. The alkaline solutions used are mono-cationic solutions of calcium, sodium and strontium. The behaviour of calcium is differentiated from the other cations. For all alkaline solutions (NaOH, Ca(OH){sub 2} or Sr(OH){sub 2}) chemical reactions consuming both hydroxide ions and their associated cations have been evidenced. These reactions are heterogenous reactions of surface adsorption by site ionization. The calcium has a different ...

International Nuclear Information System (INIS)

With the exception of some minerals, the specific activity of natural radioactive material is below 370 Bq/g, their handling thus not being subject to authorization or the duty of reporting according to section 4 para. 2 of the Radiological Protection Ordinance. Moreover, there is required no handling license for prospecting, mining and processing of radioactive minerals; they are subject to the procedures for the plans of operation of the mining laws of the Federal States. License-free handling of natural radioactive material may result in the production of radioactive waste, the disposal of which must be authorized according to sect. 47 of the Radiological Protection Ordinance if the specific activity exceeds the free amounts of column 4 in Table IV of Appendix IV by a factor of 10"-"4/g. This inconsistency is discussed by means of the following examples: (1) fly ash and slag from coal power plants, (2) flue dust from sintering plants, (3) red mud from aluminium ...

Energy Technology Data Exchange (ETDEWEB)

A permeable reactive mixture has been developed using low cost, readily available materials that is capable of providing effective, long-term phosphorous treatment in areas impacted by on-land wastewater disposal. The reactive mixture creates a geochemical environment suitable for P-attenuation by both adsorption and precipitation reactions. Potential benefits include significant reductions in phosphorous loading to receiving groundwater and surface water systems, and the accumulation of P-mass in a finite and accessible volume of material. The mixture may be applied as a component within surface treatment systems or in subsurface applications such as horizontal or vertical permeable reactive walls. The mixture averaged > 90% treatment efficiency over 3.6 years of continuous-flow laboratory column experiments. The mixture was further evaluated at the pilot-scale to treat municipal wastewater, and the field-scale to treat a well-characterized septic system plume ...

Energy Technology Data Exchange (ETDEWEB)

The Ohio State University Research Reactor (OSURR) is licensed to operate at a maximum power level of 500 kW. A pool-type reactor using flat-plate, low enriched fuel elements, the OSURR provides several experimental facilities including two 6-inch i.d. beam ports, a graphite thermal column, several graphite-isotope-irradiation elements, a pneumatic transfer system (Rabbit), various dry tubes, and a Central Irradiation Facility (CIF). The core arrangement and accessibility facilitates research programs involving material activation or core parameter studies. The OSURR control room is large enough to accommodate laboratory groups which can use control instrumentation for monitoring of experiments. The control instrumentation is relatively simple, without a large amount of duplication. This facilitates opportunities for hands-on experience in reactor operation by nuclear engineering students making reactor parameter measurements. For neutron activation analysis and ...

International Nuclear Information System (INIS)

In developing new Tc-99m brain perfusion imaging agents for SPECT, a series of BAT (bis-aminoethanethiol) derivatives was prepared. These N/sub 2/S/sub 2/ ligands formed stable and neutral complexes with reduced Tc-99m, either by Sn(II)-PPi or sodium borohydride reduction. The purity of the Tc-99m complexes was >95% (HPLC reverse-phase column, acetonitrile: pH 7.0 buffer, 85:15). The biodistribution in rats was evaluated using I-125 iodoantipyrine (IAP), a free diffusible tracer, as the internal reference. Compounds with a free hydroxyl group (I and IV) showed lower brain uptake, inspite of high P.C.; this may be related to in vivo instability of the complexes. High initial brain uptake was observed for three compounds (II, III and V), however, only compound V (P.C.=384) showed significant brain retention. Planar imaging with compound V in a monkey demonstrated that the compound localized in brain and the retention time was T/sub 1/2/=35 min. Compounds of this ...

International Nuclear Information System (INIS)

Several configurations of moderating and shielding materials have been designed and measured on the LVR-15 reactor for boron neutron capture therapy (BNCT) purposes. To determine the neutron and gamma ray space-energy distributions in the cylindrical geometry, the two-dimensional code DOT with the coupled neutron-gamma data library DLC-36 was used. The experimental verification of the beam parameters was performed in the LVR-15 reactor thermal column empty space with layers of graphite, aluminium, alumina, lead and bismuth. Attention was paid to establishing techniques and instrumentation for monitoring the neutron and gamma ray dose and beam quality. The thermal and epithermal flux densities were measured by activation foils, the neutron spectrum was determined with a Bonner spectrometer and gamma ray background with a scintillation spectrometer. The distribution of thermal neutrons in the human head phantom was mapped with a small semiconductor detector (Si"6Li). ...

Energy Technology Data Exchange (ETDEWEB)

This paper builds on earlier work to give a consistent treatment of the positive column of discharges in electronegative gases covering the transition from collisionless to collisional. In particular it seeks to elucidate the conditions under which there is an ion-ion plasma core surrounded by an electron-ion plasma, and when there is not. The parameters which describe the processes of ionization, attachment, detachment and recombination are related to the central negative ion density relative to the electron density and, where appropriate, the size of the core. The use, by earlier workers, of the Boltzmann approximation to describe the negative ion distribution and to obtain ambipolar diffusion coefficients at higher pressures is shown not to be justified. This leads to the clarification of an inconsistency in the literature. Where possible, the work is related to other recent treatments of the same problem in order to begin to build a comprehensive picture of ...