UK PubMed Central (United Kingdom)

The metabolism of ¹⁴C-labeled fatty acids and triacylglycerols was followed in intact germinating oil palm seedlings as well as in tissue slices. In the germinating seedling, the shoot contained...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Sulfated zirconia (SO4-ZrO2) catalysts, prepared with three different sulfur loading contents (0.75%, 1.8% and 2.5%) at two calcination temperatures (500degreeC and 700degreeC), were tested for use in the transesterification of purified palm oil (PPO) and the esterification of palm fatty acid (PFA) in near-critical and super-critical methanol. Techniques including BET, XRD, NH3- and CO2-TPD revealed that the sulfur content and calcination temperature strongly affects the catalyst base-acid site, specific surface area, average pore size, phase structure, and thus the catalytic reactivity. The most suitable sulfur loading content was found to be 1.8% and the optimum calcination temperature 500degreeC. The results show that the use of SO4-ZrO2 reduces esterification reaction times, the amount...

British Library Electronic Table of Contents (United Kingdom)

Poly(3-hydroxybutyrate-co-38mol%-3-hydroxyvalerate) [P(3HB-co-38mol%-3HV)] was produced by Cupriavidus sp. USMAA2-4 in the presence of oleic acid and 1-pentanol. Due to enormous production of empty fruit bunch (EFB) in the oil palm plantation and high production cost of P(3HB-co-3HV), oil palm EFB fibers were used for biocomposites preparation. In this study, maleic anhydride (MA) and benzoyl peroxide (DBPO) were used to improve the miscibility between P(3HB-co-3HV) and EFB fibers. Introduction of MA into P(3HB-co-3HV) backbone reduced the molecular weight and improved the thermal stability of P(3HB-co-3HV). Thermal stability of P(3HB-co-3HV)/EFB composites was shown to be comparable to that of commercial packaging product. Composites with 35% EFB fibers content have the highest tensile st...

UK PubMed Central (United Kingdom)

In germinating oil palm (Elaeis guineensis var D × P) seedling, an active lipase was present in the shoot but absent from both the kernel and the haustorium. It has an optimum...Full Text Available

International Nuclear Information System (INIS)

The oil palm Elaeis guineensis is usually attacked by pests, particularly, defoliating caterpillars. Between 2004 and 2006 a stinkbug predator (Asopinae) was registered preying on caterpillars of Brassolis sophorae L., Opsiphanes invirae Hubner (Lepidoptera: Nymphalidae) and Sibine spp. (Lepidoptera: Limacodidae), reducing their populations in commercial oil palm plantations in the State of Para, Brazil. Specimens of the natural enemy were collected, mounted, and identified as Alcaeorrhynchus grandis (Dallas) (Hemiptera: Pentatomidae), corresponding to the first report of the occurrence of this stinkbug attacking defoliating caterpillars of oil palm in Brazil. (author)

British Library Electronic Table of Contents (United Kingdom)

In this research, hybrid composite materials were prepared from combination of oil palm Empty fruit bunches (EFB) fibre and jute fibre as reinforcement, epoxy as polymer matrix. This study intended to investigate the effect of jute fiber hybridization and different layering pattern on the physical properties of oil palm EFB-Epoxy composites. Water absorption and thickness swelling test reveal that hybrid composite shows a moderate water absorption which is 11.20% for hybrid EFB/Jute/EFB composite and 6.08% for hybrid Jute/EFB/Jute composite. The thickness swelling and water absorption of the hybrid composites slightly increased as the layering pattern of hybrid composites changed. Hybrid composites are more water resistance and dimensional stable compare to the pure EFB composites. This is...

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Energy use patterns and utilisation efficiencies in 40 factories producing palm kernel oil (PKO) in southwestern part of Nigeria were studied. The factories were stratified into small, medium and large scale categories based on the mode of operations and production capacities. Questionnaires were administered on the factories to obtain historical data on petrol, diesel and electricity consumption and PKO production outputs for seven years (1998-2004). Energy use efficiency indicators employed include: energy intensity (EI), energy cost per unit product (EC/P), energy ratio (ER), food energy ratio (FER) and percentage oil yield by weight. Results of the study indicated that averagely, 0.58, 0.53 and 0.74GJ/103l of PKO were needed in the small, medium and large PKO factories, respectively. T...

International Nuclear Information System (INIS)

Upgrading of oil palm empty fruit bunch (EFB), which is a main by-product of palm oil industry, to animal feeds by radiation pasteurization and fermentation was investigated for recycling the agro-resources and reducing the environmental pollution. The following results were obtained: 1) The necessary dose for pasteurization of EFB contaminated by various microorganisms including aflatoxin producing fungi was determined as 10 kGy. The chemical and biological properties of EFB were changed little by irradiation up to 50 kGy. 2) In the fermentation process, Pleurotus sajor-caju was selected as the most effective fungi and the optimum condition for fermentation was clarified. The process of fermentation in suspension was also established for the liquid seed preparation. 3) The digestibility and nutritional value of fermented products were evaluated as ruminant animal feeds and the mushroom can be produced ...

British Library Electronic Table of Contents (United Kingdom)

Effect of oil palm empty fruit bunch (OPEFB) fiber and poly(methyl acrylate) grafted OPEFB on several mechanical properties of poly(vinyl chloride)/epoxidized natural rubber (PVC/ENR) blends were studied. The composites were prepared by mixing the fiber and the PVC/ENR blends using HAKEE Rheomixer at the rotor speed of 50 rpm, mixing temperature 150degreeC, and mixing period of 20 min. The fiber loadings were varied from 0 to 30% and the effect of fiber content in the composites on their ultimate tensile strength (UTS), Youngs modulus, elongation at break, flexural modulus, hardness, and impact strength were determined. An increasing trend was observed in the Youngs modulus, flexural modulus, and hardness with the addition of grafted and ungrafted fiber to the PVC/ENR blends. However the i...

Energy Technology Data Exchange (ETDEWEB)

The production of oil by retorting shale and other hydrocarbonaceous and lignocellulosic solid materials is facilitated by retorting in the presence of steam and acetic acid.

British Library Electronic Table of Contents (United Kingdom)

Recently, great interest was paid to new technologies dealing with environmental aspect. Preservation of natural resources such as natural fibers forced the composite industry to search and examine "eco-friendly" components. Studies to find alternative reinforcements and resin systems that are environmentally friendly while providing the same performance as their synthetic counterparts are in continuous progress. The aim of this study is to investigate effect of different treatment process on the data palm fiber (DPF). Raw DPF underwent different surface modification methods such as alkali treatment with concentrations 0.5%, 1%, 1.5%, 2.5% and 5%, and acid treatment with 0.3, 0.9 and 1.6N. All treatments were performed at 100degreeC for 1h. The surface morphology, thermal gravimetry analys...

International Nuclear Information System (INIS)

The GLC analysis of carthamus tinctorius (safflower) yielded average hexane extracted oil content of 28% (25-30%); the oil contained high level of linoleic acid (74%). Monounsaturated fatty acid, oleic acid amounted 12.94%, while the saturated fatty acids like palmitic acid and stearic acid were 9.43 and 1.81%, respectively. Iodine value of linoleic acid was found to be 160:1 while its purity was 93.1%. (author)

International Nuclear Information System (INIS)

Researches on oil palm empty fruit bunch (EFB) fibers and thermoplastic composites have been carried out by many workers in the last decade. The main focus was to enhance the properties of the resultant composites in view of the incompatibility of the two components. Thus, efforts have been made to enhance their properties by using coupling agents, treating the fibers and modifying the matrices. In this study, the effects of electron beam (EB) irradiation and some reactive additives (RAs) on the mechanical properties of EFB-PP (polypropylene) composites were evaluated. Different modes of irradiation were investigated. Mono, di and tri functional of monomers of RAs were used. irradiating PP alone, compared to irradiating the EFB fibers or irradiating both components, gave optimum properties for EFB-PP composites. Further, improvements of the properties of the composites were achieved with the addition of RAs with TMPTA (trymethylol propane ...

International Nuclear Information System (INIS)

Fermented oil palm empty fruit bunch, now known as 'Sterifeed' has been characterized by physico-chemical properties. It has also been proven to have an improved digestibility (by in vitro and in-vivo test) over the original material. The remaining important aspect of feed to be examined is the long term effect of feeding this material to animals. The size of fermentation media bags used was 0.5 - 1 kg/bag. In the large scale production of these materials, the numbers of bags were increased. The production at pilot scale level reinvestigated the basic processing parameters for the 1 kg/bag media and also performed a trial run for different sizes of bags. These include: 1) investigation on the growth of fungi on fermentation media subjected to different treatment times and the non treated media, 2) evaluation of the processing rate, 3) trial run processing of 25-50 MT oil palm EFB into feed, and 4) ...

International Nuclear Information System (INIS)

... PHYSICAL AND ANALYTICAL CHEMISTRY calibration standards diagrams

Energy Technology Data Exchange (ETDEWEB)

This paper presents a series of structural modifications of soybean oils for lubricant. The reaction was monitored and products were confirmed by NMR and FTIR. The structural modification is carried out in four stages, (1) synthesis of soybean oil isooctyl ester from soybean oil; (2) synthesis of epoxy-soybean oil isooctyl ester from soybean oil isooctyl ester; (3) synthesis of hydroxylated products from epoxy soybean oil isooctyl ester with fatty acid; (4) esterification of the hydroxylated product with anhydride. Rheological behaviour of the products was measured. Pour points of the products (3) were observed as low as -24 C (lauric acid) and -15 C (isooctanoic acid) respectively. When the hydroxyl groups in the products were esterified with and acid anhydride, the pour points ...

Energy Technology Data Exchange (ETDEWEB)

A hydrocarbon composition having a major portion of a hydrocarbon preferably a lubricating oil such as mineral oil and at least a friction-reducing amount usually 0.01 to 10 weight percent of an amine or amine derivative of a hydrocarbon-soluble polymerized fatty acid e.g. a dimeramine derived from a dicarboxylic acid containing at least 12 carbon atoms such as 9(10)-carboxy stearic acid has improved antifriction and flue economy properties.

British Library Electronic Table of Contents (United Kingdom)

The potential of water extracts produced from rice straw (RST) and empty fruit bunch of oil palm (EFB) composts fortified with Trichoderma harzianum for the control of Choanephora wet rot of okra caused by Choanephora cucurbitarum was studied under field conditions. Disease severity was lowest in plants treated with Trichoderma-fortified RST extracts (9.56%) with a disease index of 1, mancozeb (Dithane M-45 (2gl-1 of water), Trichoderma-fortified EFB compost extracts, extracts of RST and EFB, and an aqueous suspension of T. harzianum recorded disease severity values of 10.25%, 19.38%, 37.56%, 53.71% and 56.36%, with a disease index of 1, 1, 2, 3 and 3, respectively. There was a reduction of 85.04% in Choanephora wet rot severity on okra treated with Trichoderma-fortified RST extracts durin...

Energy Technology Data Exchange (ETDEWEB)

This paper reported on a study in which rapeseeds were separated into high quality seed for food oil and low quality seed for biofuels. A laboratory-scale oilseed screw press was then used to examine the effects of choke opening and seed preheating on the rapeseed pressing performance and the quality of food oil and biofuels oil. Oil recovery and chlorophyll content was found to increase as maximum pressure increased. In terms of pressing performance, the rapeseed heated by microwaves yielded more oil and chlorophyll than without heating. The NEB ratio of microwave heating press with an 8.0 mm choke opening was advantageous. Rapeseed oil extracted from low quality seeds was found to have a high acid value. The quality of oil extracted by oilseed screw press was found to be good and met the requirements of the Codex ...

Energy Technology Data Exchange (ETDEWEB)

Biodiesel is produced from vegetable oils that have been chemically modified by esterification; an example is rapeseed oil methyl ester (RME), made by treating rapeseed oil with methanol. Biodiesel can be burned directly in diesel engines. Oil from the rapeseed variety known as 00 was the first type of vegetable oil used for transesterification to produce biodiesel. Many other oils have been used successfully as biodiesel feedstock including sunflower oil in Southern France and Italy, soybean oil in the USA, and palm oil in Malaysia. Biodiesel can be made from a wide range of feedstock and multi-feedstock blends. Compared to conventional diesel biodiesel has some environmentally friendly advantages, e.g. biodiesel is reported to release fewer solid particles. Potentially even ...

British Library Electronic Table of Contents (United Kingdom)

Waste cooking oil can be recovered and processed into animal feed additives after purification. Unfortunately, the traditional purification processes are insufficient for the removal of the harmful compounds formed during frying, mainly about malondialdehyde and other 2-thiobarbituric acid reactive substances. In the present paper, firstly, a simple and reliable HPLC method was developed to measure the content of malondialdehyde in purified waste cooking oil. The detection limit and the standard recovery of the analysis method are 1.20x10-5gl-1 and 96.5-99.2%, respectively, which is accurate and valid enough for the detection of malondialdehyde in waste cooking oil. Furthermore, the removal of malondialdehyde and other 2-thiobarbituric acid reactive substances from waste cooking oil was in...

International Nuclear Information System (INIS)

The 12 months stability study of freshly produced refined soybean oil revealed that refined soybean oil stored in plastic containers in dark was more hydrolytically and oxidatively stable than that stored in other containers in light condition. There was no significant difference at P < 0.05 in free fatty acids and acid value of oil stored under light and dark conditions in tin and glass containers but there was significant difference at P < 0.05 in peroxide value of oil stored in light and dark conditions in all the storage containers. Light increased the degree of oxidative rancidity of refined soybean oil, the most in tin containers, followed by glass containers and the least in plastic containers. (author)

Energy Technology Data Exchange (ETDEWEB)

A procedure for the determination of carboxylic acids (benzoic and C{sub 8}-C{sub 16} aliphatic acids) in oxidised engine oils is described. It is based on a simple and selective derivatisation of the acids with a fluorescent label 9-anthracene-methanol followed by reverse-phase separation on an ODS column with a water-acetonitrile-tetrahydrofuran (20:40:40 by volume) mobile phase and post-column reaction with bis(2,4-dinitrophenyl) oxalate and hydrogen peroxide. The chemiluminiscence emission from the reaction was monitored using a lamina flow-through detector. Analysis of oxidised oils showed that although there was quenching of chemiluminiscence emission by the oil matrix, the acids could be determined over the range 0-0.4% (m/v) in the oil with a detection limit of 0.013% (m/v) (130 pmol on-column with a 20 {mu}l ...

International Nuclear Information System (INIS)

(1973). United States Kylstra, CD West Palm Beach, Florida, USA. 25 Apr 1973.

Energy Technology Data Exchange (ETDEWEB)

Biodiesel consists of long-chain fatty acid esters, derived from renewable sources such as vegetable oils, and its utilization is associated to the substitution of the diesel oil in engines. Depending on the raw material, bio diesel can contain more or less unsaturated fatty acids in its composition, which are susceptible to oxidation reactions accelerated by exposition to oxygen and high temperatures, being able to change into polymerized compounds. The objective of this work was to determine the oxidative stability of bio diesel produced by ethanolysis of neutralized, refined, soybean frying oil waste, and partially hydrogenated soybean frying oil waste. The evaluation was conducted by means of the Rancimat equipment, at temperatures of 100 and 105 deg C, with an air flow of 20 L h{sup -1}. The fatty acid composition was determined by GC ...

British Library Electronic Table of Contents (United Kingdom)

Desulphurization of gasoline and kerosene was carried out using organic and inorganic oxidants. Among the organic oxidants used were hydrogen peroxide in combination with acetic acid, formic acid, benzoic acid and butyric acid, while inorganic oxidants used included potassium permanganate and sodium perchlorate. The oxidation of each petroleum oil was carried out in two steps; the first step consisted of oxidation of the feed at moderate temperature and atmospheric pressure while in the second step, the oxidized mixture was extracted with azeotropic mixture of acetonitrile-water. A maximum desulphurization has occurred with NaClO4 and hydrogen peroxide and acetic acid, which are 68% and 61%, respectively in case of gasoline and 66% and 63%, respectively in case of kerosene oil. The FTIR st...

British Library Electronic Table of Contents (United Kingdom)

Experiment was conducted to study the effect of gamma irradiation, growth retardants and coatings (coconut oil, mustard oil and liquid paraffin) on shelf life of winter guava fruits during storage. The results revealed that the superiority of coconut oil coating over other post harvest treatments. Physiological loss in weight (7.1%), marketable fruits retained over control (86.7%), total soluble solid (16.1%), ascorbic acid (195 mg/100 g pulp) and total sugar (10%) of fruit were positively influenced by coconut oil coating up to 12 days of storage. The treatment was found significantly effective in increasing the post harvest life of fruits for 12 days over control without adversely affecting the fruit quality. Coconut oil coating gave highest consumer acceptability while, maintaining suff...

Energy Technology Data Exchange (ETDEWEB)

In this work some physicochemical properties and the thermal behavior and stability of sour sop or guanabana (Annona muricata) seed almond oil were studied by means of chemical, DSC and TG analysis. The results showed that the almond has 2.5% ash, 17.9% crude fiber, 15.7% protein, 26.0% de carbohydrates and 37.7% oil (dry base). The composition of almond oil showed 68.5% unsaturated fatty acids, mainly oleic and linoleic, and some palmitoleic acids, and 31.5% saturated, principally palmitic and stearic fatty acids; refraction index was 1.468 and saponification and iodine value were 168.2 and 87.0, respectively. DSC thermal analysis showed that oil crystallization initiates at -4.5 degree centigrade and ends at -79.0 degree centigrade with a crystallization enthalpy of 48.2 J/g; the oil melts in a temperature range from ...

Energy Technology Data Exchange (ETDEWEB)

Cuphea, a relatively unknown plant outside the scientific community, might someday provide valuable oils for manufacturing soaps, detergents, surfactants, and lubricants, and may have medical, nutritional and dietetic applications as well. Unique properties of oils found in its seed make cuphea a potentially valuable new crop for the USA. Its seeds contain large quantities of medium-chain fatty acids such as lauric acid, which is used in manufacturing soaps and detergents. Other medium-chain fatty acids in cuphea can be used for clinical treatment of rare human ailments associated with fat absorption. New uses for the fatty acids in the seed may be developed and economic conditions may change, making the crop more or less valuable.

Energy Technology Data Exchange (ETDEWEB)

Red mud, and red mud activated by dissolution in hydrochloric acid and reprecipitation with ammonia, were tested as catalysts for the hydrogenation of an anthracene oil in a trickle-bed reactor. Conversion data were determined for the different polyaromatic compounds in the anthracene oil. Red mud shows appreciable catalytic activity, which is enhanced by the activation. Although both red mud and activated red mud are less active than a commercial Ni-Mo/[gamma]-alumina hydrotreating catalyst, the difference in activity is smaller when conversion to hydroaromatics instead of total conversion of reactants is considered. 20 refs., 8 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

This opinion presents an overview of recent developments in the diagnosis and treatment of hepatocellular carcinoma (HCC) in Japan. The use of Ethiodol (iodized ethyl ester of the fatty acid of poppyseed oil) for hepatic angiography in diagnosing and treating (combined with chemotherapeutic agents) HCC has been reported. Ethiodol has been found to localize in HCC and remain there for long periods. The implications of these findings are discussed.

Energy Technology Data Exchange (ETDEWEB)

In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude ...

British Library Electronic Table of Contents (United Kingdom)

In this study, a two-step process was developed to produce biodiesel from Calophyllum inophyllum oil. Pre-treatment with phosphoric acid modified b-zeolite in acid catalyzed esterification process preceded by transesterification which was done using conventional alkali catalyst potassium hydroxide (KOH). The objective of this study is to investigate the relationship between the reaction temperatures, reaction time and methanol to oil molar ratio in the pre-treatment step. Central Composite Design (CCD) and Response Surface Methodology (RSM) were utilized to determine the best operating condition for the pre-treatment step. Biodiesel produced by this process was tested for its fuel properties.

Energy Technology Data Exchange (ETDEWEB)

Mineral oil based power transmitting fluids, such as automatic transmission fluids, are disclosed which contain 0.05 to 2.0 weight percent of an ester of a thio-bis alkanol and a C/sub 12/-C/sub 50/ hydrocarbon succinic acid or anhydride, the ester being a multifunctional additive providing the properties of friction modification, corrosion inhibition, anti-wear, oxidation inhibition and extreme pressure properties to the fluids.

Energy Technology Data Exchange (ETDEWEB)

Three enriched cultures (48, 15a, and 26a), selected from more than 80 soil and water samples, could grow anaerobically in the presence of crude oil at 30{degrees}C and could ferment molasses to gases and organic acids. Oil recovery by culture 48 in the laboratory model experiment was enhanced by 25.2% over the original reserves and by 53.7% over the residual reserves. Enriched culture 48 was composed of at least 4 species belonging to the genera Eubacterium, Fusobacterium, and Bacteroides. This enriched culture was used as inoculum for MEOR field trials at Jilin oil field with satisfactory results. The importance of the role of these isolates in EOR was confirmed by their presence and behavior in the fluids produced from the microbiologically treated reservoir.

British Library Electronic Table of Contents (United Kingdom)

This work reports phase equilibrium measurements for the ternary systems linoleic (acid+CO2+ethanol) and (linolenic acid+CO2+ethanol). The fatty acids present in the ternary systems were selected based on composition of banana peel oil extracted by supercritical CO2 at 20MPa and 313K. The motivation of this research relies on the fact that these unsaturated fatty acids are recognized to play an important role in lowering blood pressure and serum cholesterol and because they are present in high concentrations in banana peel extract. Besides that, equilibrium data of these compounds are scarce in literature. The phase equilibrium experiments were performed using a high-pressure variable-volume view cell over the temperature range of (303 to 343)K and pressures up to 19MPa. For both systems, ...

British Library Electronic Table of Contents (United Kingdom)

Abstract As a marine carnivore exhibiting exceptionally high growth rates, cobia are considered a species for which fish oil (FO) replacement may be difficult. However, partial, if not complete, FO replacement is necessary to ensure sustainability. We evaluated the effects of graded substitution of dietary FO with soybean oil (SO) in cobia culture. Feeds contained FO (100% FO), SO (0% FO) or blends of the two (67% FO, 33% FO) as the supplemental lipid source. Production performance was largely unaffected by partial replacement of FO with SO: feed intake and final weight were reduced only in the 0% FO dietary treatment. Fillet total lipid fatty acid (FA) composition differed among the dietary treatments, closely approximating dietary FA profile. As increasing amounts of FO were replaced, SO...

Energy Technology Data Exchange (ETDEWEB)

Negative ion electrospray ionization (ESI) coupled with high field Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) allows for the direct detection of acidic NSO compounds in petroleum. The technique requires no chromatographic separation, is able to distinguish 18 different compound classes (e.g., neutral nitrogen, carboxylic acids and oxygenates), and can identify {approx}14,000 distinct masses by ultra-high mass resolution and mass accuracy. We previously studied three crude oils from different geological origins [Organic Geochemistry 33 (2002b) 743-759]. Here, we expand our research by comparing two source-equivalent Smackover oils of different levels of thermal maturity. We observe clear differences in the distribution of NSO compound classes, types (number of rings plus double bonds within a class), and number of alkyl carbons. With increasing thermal stress, the relative ...

British Library Electronic Table of Contents (United Kingdom)

Precision agriculture can be cost effective for date palm groves because the tree positions are known and fixed, the groves are mostly structured and many of agricultural operations are applied manually. Therefore, the new technology tools of precision agriculture are not essential. This study was done to improve date palm yield using maps of the variation in tree properties. Data on five Mozafati tree properties, such as sex, age, yield, visual appearance and fruit length were measured and recorded for each tree in five groves near the city of Bam in Iran. Tree positions were defined and the above properties were mapped. It was difficult to judge patterns in the variation because of tree to tree variability. Therefore, the Mamdani fuzzy inference system (MFIS) was used to classify the pro...

Energy Technology Data Exchange (ETDEWEB)

Among the several chemical processes conducted for the removal of organic matter present in wastewaters coming from some agro-industrial plants (wine distilleries, olive oil mills, etc), the oxidation by ozone has shown a great effectiveness in the destruction of specially refractory pollutants: it is demonstrated that the biodegradability of those wastewaters increases aflcer an ozonation pretreatment. Their great pollutant character is imputed to the presence of some organic compounds, like phenols and polyphenols, which are toxic and inhibit the latter biological treatments. In this research, a competitive kinetic procedure reported by Clurol and Nekouinaini is applied to determine the degradation rate constants by ozone of several phenolic acids which are present in the wastewaters from the olive oil obtaining process. The resulting kinetic expressions for the ozonation reactions are useful for the successful design and ...

Energy Technology Data Exchange (ETDEWEB)

Kitchen oils (olive, soybean and butter) are selected for carbon coatings on LiFePO{sub 4}. The surface properties of LiFePO{sub 4} are unknown or vary depending on synthetic methods. The multi-functional groups of fatty acids in the oils can orient properly to cope with the variable surface properties of LiFePO{sub 4}, which can lead to dense carbon coatings. The low price and low toxicity of kitchen oils are other advantages of the coating process. LiFePO{sub 4} (D{sub 50} = 121 nm)combined with the carbon coating enhances the rate capability. Capacities at the 2C rate reach 150 mAh g{sup -1} or higher. The charge retention values of 2.0C/0.2C are between 94.4 and 98.9%. (author)

UK PubMed Central (United Kingdom)

Tinea nigra is a superficial mycosis caused by Hortaea werneckii. It is an infrequent asymptomatic infection that affects human palms and soles, and is mostly observed in tropical...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The production of heavy crude oils increased in the last years in the world. Crude oils with high density, viscosity, acidity and sulfur, nitrogen, metals and asphaltenes contents, by the others hand, low stability and low product quality. The challenger of many refiners is find solutions to refine the heavy crude oils, and produce fuels with certify quality, such as Jet Fuel. The principal aviation technique on the world work with gas turbines engines feted for jet fuel (JET A1). The quality specifications of this fuel are establish by International Norms: ASTM-1655, DEF STAN 91-91-3 (DERD 2494) and joint Fuelling System Check List. The world technologies to obtain jet fuel from mixtures of heavy crude oil with middle crude oils are: Atmospheric distillation, with a posterior hydrogenation and finally the additivation. Studies carried out have demonstrates that ...

Energy Technology Data Exchange (ETDEWEB)

Research is presented on oil and gas technologies, advanced systems, soil remediation and remediation of acid mine drainage, applied science research in plastics and petroleum coprocessing, and fossil fuel and hydrocarbon conversion using a hydrogen rich plasmas.

Energy Technology Data Exchange (ETDEWEB)

The analysis described demonstrates the use of benefit/cost sensitivity analysis in examining the wide range of potential damages and savings associated with converting oil-fired electric utility boilers to burn coal in Florida. This model, for the first time incorporates, in quantitative terms, environmental economic externalities into a benefit/cost ratio sensitivity analysis framework. Five different dose-response estimates of morbidity and mortality costs, property devaluation, and willing-to-pay estimates are used in combination with four acid rain dose-response models to estimate the net present worth of externality costs. The model estimates the net present worth of benefits by incorporating into a dynamic framework all relevant construction, O + M, and fuel costs of converting an electrical generation facility from using oil to coal. These benefits of fuel savings are then weighted against various combinations of ...

Energy Technology Data Exchange (ETDEWEB)

This article describes the chemical preparation of petroleum additives of the MASK type from samples of concentrated alkylsalicylic acids. The obtained additives contain high contents of calcium alkylsalicylate and respective total alkalinities of 156, 131, and 130 mg KOH/g. Sodium alkylsalicylate concentrates, obtained in the form of an aqueous acetone solution, were converted to alkylsalicylic acids by interaction with hydrochloric acid. The solvent was removed from the upper and lower layers by distillation, and the resulting products were analyzed by liquid chromatography. Service tests were performed on a model formulation of the additive in M-11 oil in a Petter AV-1 test stand unit in comparison with commercial MASK additive. The results indicate that the model additive formulation gives approximately the same corrected piston fouling ratings as the commercial additive.

Energy Technology Data Exchange (ETDEWEB)

Mild hydrotreating is the key to successful re-refining of used lubricating oils. Coupled with pre-distillation and metals removal, the process produces oil of superior color and clarity with acceptable viscosity and heteroatom content. Furthermore, the entire process provides operational simplicity, economic feasibility and environmental attractiveness. Re-refining preserves a valuable resource while solving a potential environmental problem. Increased sensitivity to disposal of hazardous material once again makes re-refining almost a necessity. Various technologies developed to re-refine used lubricating oils range from simple acid/clay contacting to complex solvent extraction. Most technologies require similar capital investment; however, operating costs vary substantially. Current technology seems to converge on a two-step procedure: distillation of dehydrated used oil in a ...

Energy Technology Data Exchange (ETDEWEB)

Rats from an inbred Sprague-Dawley strain were fed semisynthetic diets with a low (0.3 energy percent (en %)), normal (3 en %) or high (10 en %) content of essential fatty acids (EFA) for at least three generations. Twenty-nine- to 33-day-old male rats were given a single intragastric dose of (1-14C)linoleic acid in olive oil, and the respiratory CO2, urine and feces were collected for 46 hours (expt 1) or 20 hours (expt 2). The 14C activity in respiratory CO2, feces, urine and the carcass was determined in both experiments. In experiment 2 it was also measured in samples of the brown fat, liver, adrenals, white fat, skeletal muscles and brain. In both experiments the rats fed the low EFA diet retained significantly more 14C activity than the rats fed the normal or high EFA diets. In all groups the concentration of label was highest in the brown fat and the adrenals, but the above differences among the groups with respect ...

Energy Technology Data Exchange (ETDEWEB)

Small swabs are often dampened with a solvent when used to clean surfaces. Cotton swabs of the type sold in drug stores contain stearic acid, probably used as a lubricant during manufacture of the swab. Such swabs, dampened with a solvent and used to clean a surface, will leave a film of stearic acid on the surface. Several kinds of swabs are sold for industrial use, and some are described as suitable for use in clean room manufacturing. Nine different swabs, some cotton and some urethane foam, were extracted with isopropyl alcohol, CFC 113 (Freon TF or Genesolv D), or mixture of CFC 113 and methyl alcohol. After evaporation of the solvent, from 0.5 to 3.8 mg of an oil or grease remained. For critical applications, swabs should be washed with solvent before use.

Energy Technology Data Exchange (ETDEWEB)

Hydrolysis of olive oil by Chromobacterium viscosum lipase was studied in a reverse micellar system of a anionic surfactant Aerosol OT (AOT) and isooctane. Different methods of solubilization of the micellar system afford specific dependence of enzymatic activity of the lipase on the water content in the micelles. In an injection method, water content is controlled by the amount of injected water, which determines the micelle size and hydrophobicity of the micelle without salt addition and changes reversibly the conformation of lipase corresponding to the change of lipase activity. The activity reaches the maximum at a water content (water/AOT)of 7. In a phase transfer method, water content is determined by salt concentration in the aqueous phase in contact with micelles and the water content corresponding to the maximum activity is 12 to 13, below which the activity decrese drastically. Addition of taurodeoxycholic acid to the AOT micelles ...

British Library Electronic Table of Contents (United Kingdom)

Hexane extract of licorice (Glycyrrhiza glabra L.) roots was obtained and investigated. Hydrocarbons, sterol ethers, triacylglycerides, free fatty acids, and free sterols were identified. The extract contains 70% neutral and 30% polar lipids. It is established that the lipid fraction of licorice roots is more effective than the analogous fraction of rosehip oil in stimulating the reparative regeneration of skin. In addition, this fraction also exhibits pronounced antiinflammatory and antiulcer effects, while being virtually nontoxic. Based on these results, the lipid fraction of licorice roots can be recommended as a parent substance for creating effective preparations in various medicinal forms.

British Library Electronic Table of Contents (United Kingdom)

The effect of chemical pretreatments using NaOH, H2O2, and Ca(OH)2 on Empty Palm Fruit Bunches (EPFB) to degrade EPFB lignin before pyrolyis was investigated. Spectrophotometer analysis proved consecutive addition of NaOH and H2O2 decomposed almost 100% of EPFB lignin compared to 44% for the Ca(OH)2, H2O2 system while NaOH and Ca(OH)2 used exclusively could not alter lignin much. Next, the pretreated EPFB was catalytically pyrolyzed. Experimental results indicated the phenolic yields over Al-MCM-41 and HZSM-5 catalysts were 90wt% and 80wt%, respectively compared to 67wt% yield for the untreated sample under the same set of conditions. Meanwhile, the experiments with HY zeolite yielded 70wt% phenols.

International Nuclear Information System (INIS)

The effects of the antioxidants, vitamin E, propyl gallate, 2-t-butyl-4-methoxy phenol (BHA), 2,6-di-t-butyl-4-methoxy phenol (BHT), nor-dihydroguaiaretic acid (NDGA) and diphenyl-p-phenylene diamine (DPPD) in concentrations ranging between 0.001 per cent and 0.1 per cent have been tested on lipid peroxide formation in synthetic diet mixtures containing herring oil (10 per cent) mixed with starch (90 per cent) irradiated with #gamma#-ray doses of 100 to 2000 krad. On a weight basis NDGA, DPPD, BHA and BHT were most effective and vitamin E and propyl gallate were least effective. An antioxidant concentration of 0.01 per cent normally protected against peroxide formation after a dose of 500 krad but if the dose was increased to 1000 or 2000 krad, much higher doses of antioxidant, up to 0.1 per cent, were required to give protection. Antioxidants prevented peroxide developing during post-irradiation storage even when added after irradiation. ...

International Nuclear Information System (INIS)

The chemical composition and evolution of formation waters associated with gas production in the Palm Valley field, Northern Territory, has important implications for reservoir management, saline water disposal, and gas reserve calculations. Historically, the occurrence of saline formation water in gas fields has been the subject of considerable debate. A better understanding of the origin, chemical evolution and movement of the formation water at Palm Valley has important implications for future reservoir management, disposal of highly saline water and accurate gas reserves estimation. Major and trace element abundance data suggest that a significant component of the highly saline water from Palm Valley has characteristics that may have been derived from a modified evaporated seawater source such as an evaporite horizon. The most dilute waters probably represent condensate and the variation in the chemistry of the ...

Energy Technology Data Exchange (ETDEWEB)

Non-edible filtered high viscous (72 cSt at 40{sup o}C) and high acid value (44 mg KOH/gm) polanga (Calophyllum inophyllum L.) oil based mono esters (biodiesel) produced by triple stage transesterification process and blended with high speed diesel (HSD) were tested for their use as a substitute fuel of diesel in a single cylinder diesel engine. HSD and polanga oil methyl ester (POME) fuel blends (20%, 40%, 60%, 80%, and 100%) were used for conducting the short-term engine performance tests at varying loads (0%, 20%, 40%, 60%, 80%, and 100%). Tests were carried out over entire range of engine operation at varying conditions of speed and load. The brake specific fuel consumption (BSFC) and brake thermal efficiency (BTE) were calculated from the recorded data. The engine performance parameters such as fuel consumption, thermal efficiency, exhaust gas temperature and exhaust emissions (CO, CO{sub 2}, HC, NOx, and O{sub 2}) ...

CERN Document Server

Radiation protection and the management of radioactive waste in the oil and gas industry

International Science & Technology Center (ISTC)

Determination of the Ecology Factor for the Magistral Oil Pipelines, Working in Difficult Hilly and Geology Conditions

Science.gov (United States)

No Abstract Available

Energy Technology Data Exchange (ETDEWEB)

In the third quarterly report adsorption of heavy metals ions such as Cu(II) and Cr(VI) onto soils drawn from the laboratory-type wetland was shown to be weak. Secondly, it was shown that modified-clays did adsorb Cr(VI) ions strongly at pH 4.5. Further, studies on the pH dependence of the adsorption of {beta}-naphthoic acid, (NA), a well-documented contaminant in many oil and gas well waste waters onto modified-clays were undertaken and it was shown that uptake of NA by modified-clays was of the high affinity type at pH 4.5 and 7.0, but weak at pH 9.0. Adsorption of heavy metal ions, Cu{sup 2+}, and Cr(VI) onto algae, a proposed wetland amendment, was carried out and the results were presented and discussed in the fourth quarterly report. Uptake of NA by the soil component of the laboratory-type wetland was monitored as a function of pH. This quarterly report presents results from studies on the uptake of phenol and {beta}-naphthoic ...

Energy Technology Data Exchange (ETDEWEB)

Trying to achieve the optimal utilization of oil shale resources, and the production of a more environmentally acceptable fuel, as well as a solid waste with a low a sulphur content, thereby reducing acidic leachates, has led to this investigation. In this article, the influences of the bed temperature and the choice of fluidizing gas on the quality and quantity of the produced fuel gas, using a continuous feed fluidized bed reactor, were investigated. The composition and calorific value of the generated gas were determined. There was a nearly linear increase in the amount of fuel gas produced as a function of temperature, reaching {approx}350 kg per 10{sup 3} kg of dry raw shale and the gross calorific value ranged from 15 to 23 MJ-kg{sup -1} with CO and H{sub 2} being the major constituents. Subsequent experiments were carried out, employing a thermogravimetric analyser under similar conditions as applied to the fluidized bed reactor. ...

Energy Technology Data Exchange (ETDEWEB)

The coke plant at the Sparrows Point Plant consist of three coke oven batteries and two coal chemical plants. The by-product coke oven gas (COG) consists primarily of hydrogen, methane, carbon monoxide, nitrogen and contaminants consisting of tars, light oils (benzene, toluene, and xylene) hydrogen sulfide, ammonia, water vapor and other hydrocarbons. This raw coke oven gas needs to be cleaned of most of its contaminants before it can be used as a fuel at other operations at the Sparrows Point Plant. In response to environmental concerns, BSC decided to replace much of the existing coke oven gas treatment facilities in the two coal chemical Plants (A and B) with a group of technologies consisting of: Secondary Cooling of the Coke oven Gas; Hydrogen Sulfide Removal; Ammonia Removal; Deacification of Acid Gases Removed; Ammonia Distillation and Destruction; and, Sulfur Recovery. This combination of technologies will replace the existing ammonia ...

International Nuclear Information System (INIS)

A stratigraphic and geochemical study of alpine soils, which formed in later Pleistocene (late glacial) and Neoglacial deposits in the Wind River Mountains of western Wyoming, indicates that these soils are affected by air-fall in flux of inorganic pollutants. Arsenic, bromine and antimony appear to have been deposited in surface soils by incorporation of aeolian materials which were presumably transported by winds from industrial sources, including coal-burning operations. As vanadium was not found in surface soils at concentrations above site-specific background levels, oil-fired energy generating stations were not found to be significant sources of surface soil pollution in the region. Acid-rain effects were not observed in the soils. (author) 32 refs.; 2 figs.; 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

Three alternative extraction procedures were carried out in order to separate the antioxidant components and isolate an efficient extract from Origanum dictamnus. Procedure A included sequential extractions with petroleum ether (PE), diethyl ether (DE) and ethanol; procedure B sequential extractions with PE and ethyl acetate (EAc); procedure C a single step extraction with ethanol. The most efficient radical scavengers, according to the DPPH method, were isolated in ethanol extract of procedure A (mainly rosmarinic acid), followed by ethanol extract of procedure C. However, both ethanol extracts had low solubility in oil and could not protect it. EAc and DE extracts, containing mainly apigenin and epirosmanol ethyl ether, presented lower radical scavenging activity but were very effective ...

Energy Technology Data Exchange (ETDEWEB)

Ammonium nitrate shale oil explosives are provided which are effective, powerful, inexpensive, and safe. The explosives contain about 2% to 10% by weight shale oil and about 90% to 98% by weight ammonium nitrate. The shale oil can be whole shale oil or heavy shale oil containing from 0.1% to 65% by weight oil shale dust. The ammonium nitrate is preferably in the form of explosive grade ammonium nitrate prills.

Energy Technology Data Exchange (ETDEWEB)

This paper presents results of a laboratory and field study of naphthenic acid corrosion and the development of an effective chemical inhibitor for this type of corrosive attack. In the laboratory corrosion test, which involved 20 hour weight loss measurements in high flash solvent with a total acid number (TAN) of 16 mg KOH/gm at a temperature of 600 F (316 C), blank corrosion rates averaged 140 to 150 mpy (3.56 to 3.81 mm/y). Inhibited rates averaged about 10 to 12 mpy (0.254 to 0.305 mm/y). The field test was carried out on a heavy vacuum gas oil (HVGO) stream at 550 F (288 C) . Blanks varied from a high of 425 mpy (10.79 mm/y) for a 24 hour test to a low of about 100 mpy (2.54 mm/y) for a 150 hour test. Both electrical resistance (ER) probes and weight loss coupons showed corrosion rates below 5 mpy (0.127 mm/y) as long as they were adequately passivated. Passivation consisted of exposing the coupons to a high inhibitor ...

British Library Electronic Table of Contents (United Kingdom)

Sustainability of irrigated agriculture in arid and semi arid lands depends, mainly on the level of soil salinity and the quality of irrigation water. Remotely sensed data can provide information about the extent of vegetated irrigated areas. Al-Hassa oasis, Saudi Arabia is probably the largest oasis in the world depends mostly on tapped ground water to irrigate mainly date palm groves for its economic survival. This study tried to investigate the extent of soil salinity and the quality of irrigation water and the relationship with vegetation growth, employing NDVI derived from Landsat satellite imagery.

International Nuclear Information System (INIS)

The chemical composition and evolution of produced waters associated with gas production in the Palm Valley gas field, Northern Territory, has important implications for issues such as gas reserve calculations, reservoir management and saline water disposal. The occurrence of saline formation water in the Palm Valley field has been the subject of considerable debate. There were no occurrences of mobile water early in the development of the field and only after gas production had reduced the reservoir pressure, was saline formation water produced. Initially this was in small quantities but has increased dramatically with time, particularly after the initiation of compression in November 1996. The produced waters range from highly saline (up to 300,000 mg/L TDS), with unusual enrichments in Ca, Ba and Sr, to low salinity fluids that may represent condensate waters. The Sr isotopic compositions of the waters ("8"7Sr/"8"6Sr = 0.7041-0.7172) are ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Wastenet

... It stands at a precipice of \\

Energy Technology Data Exchange (ETDEWEB)

A radial-flow type internally oil-cooled oil-filled cable has been developed. This system is characterized in that the oil flows radially through the paper insulation. The thermal resistance of the insulation is equivalently decreased by the radial-flow. The decreased thermal resistance as well as the cooling effect of the oil flow in the central oil duct and the outer oil duct under an aluminum sheath increase the current capacity. A calculation method of cooling characteristics is introduced. The stability of the cable and accessories was confirmed through initial electrical tests and a long-term field test.

Energy Technology Data Exchange (ETDEWEB)

This book provides discusses recent developments in oil pollution control instrumentation. Some of the topics covered are as follows: 1. Technical requirements of the IMCO International Performance and Test Specification A393x concerning oil content meters; and 2. Oil in water detection; and 3. Methods for the disposal of recovered oil and oily sludge; and 4. Oil content monitoring at ballast water treatment facilities and offshore production platforms.

Energy Technology Data Exchange (ETDEWEB)

In China, the conventional utilization of oil shale is concentrated mainly on retorting oil shale to produce shale oil and fuel gas, and burning oil shale to generate electricity. The growth of petroleum price, and the development in heavy industry, make these conventional utilization facilities become unavailable on the energy market. In this paper, a new comprehensive utilization system is recommended for the future use of Huadian oil shale, based on the current status of energy and the characteristics of oil shale. The system involves three subsystems: retort subsystem, where coarse oil shale (8-80 mm) is retorted to shale oil, hydrocarbon gases and oil shale semicoke; combustion subsystem, where the mixture fuel of oil-shale semicoke and fine oil shale ...

UK PubMed Central (United Kingdom)

In this observational study, we compared erythrocyte membrane fatty acids in infants consuming formula supplemented with docosahexaenoic acid (DHA) and arachidonic acid (ARA) with those consuming...Full Text Available

UK PubMed Central (United Kingdom)

The effect of low concentrations of nalidixic acid on ribonucleic acid (RNA) synthesis in Escherichia coli was examined. It was observed that RNA synthesis in exponentially growing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In China, the conventional utilization of oil shale is concentrated mainly on oil shale retorting, and burning oil shale in pulverized furnaces, or bubbling fluidized beds. To improve the availability of oil shale, many specialists have advocated burning oil shale in a circulating fluidized bed (CFB), which has a satisfactory combustion efficiency, low NOx and SO{sub 2} emission, adaptability to low-grade coal, etc. In Huadian, China, a plant incorporating three units of 65 th{sup -1} oil shale-fired CFB began successful commercial operation in 1996, proving that burning oil shale in a CFB produces both high combustion efficiency and environmental protection. For effective utilization of oil shale, its pyrolysis and combustion characteristics, emission performance of gaseous pollutants from an oil ...

Science.gov (United States)

Hydrogenation of high-volatile bituminous coal under high temperatures and pressures produced low-sulfur fuel oils. At a coal conversion of 80 percent, the ratio of oil to gas yields was approximately 3 : 1 and 23 percent of the coal sulfur was contained in the oil. Sulfur content of the oil, however, remained the same at different coal-conversion levels. The data obtained in the semicontinuous dilute-phase hydrogenation system showed that the whole oil can be directly used as a fuel oil where 1 percent sulfur is tolerated. Fuel oils containing 0.5 percent and 0.25 percent sulfur were produced by desulfurization of the whole oil.

Energy Technology Data Exchange (ETDEWEB)

The paper-insulated low-pressure oil-filled cable invented in 1917 has been used throughout the world as the major cable system for voltages from 33kV to 525kV and experimentally to 1100kV. The proven reliability of the design is amply demonstrated by the cables installed in the early 1930s still currently in service. The inherent design of an oil-filled cable requires that the low viscosity oil is retained within a lead or aluminium sheath. Changes in oil volume due to changes in ambient temperature and load are accommodated by oil reservoirs which maintain the cable oil pressure within design limits. A microprocessor monitoring system that allows early detection and quick location of oil leaks from high voltage oil-filled cables is described.

International Nuclear Information System (INIS)

Thallium-201 diethyldithiocarbamate (DDC) behaves like a chemical microsphere and is trapped by spontaneous decomposition in the brain in proportion to regional perfusion. They have shown that the technetium-99m analog, Tc-99m DDC (1), is unsuitable for cerebral perfusion imaging because it does not decompose rapidly enough to be trapped in the brain. With the goal of turning this greater stability of 1 into an advantage, a series of dithiocarbamates with lipophilic or amine groups designed to enhance cerebral uptake and retention was prepared from the following amines by reaction with carbon disulfide and sodium hydroxide: pyrrolidine (2), piperazine (3), 4-benzylpiperazine (4), and 4-(1-piperidino)piperidine (5). These ligands (5 mg) were labelled with Tc-99m in > 95% efficiency (ITLC-SG, saline) by reduction of pertechnetate at room temperature with formamidine sulfinic acid at alkaline pH. In preliminary studies, 4 and 5 show a trend of increasing ...

Energy Technology Data Exchange (ETDEWEB)

Polycyclic aromatic hydrocarbons (PAH`s) are ubiquitous hydrophobic organic pollutants in the marine environment. Many of the PAM`s are classified as possible carcinogens or mutagens, therefore they are of considerable concern to human and environmental health. The highest concentrations are found in coastal regions due to anthropogenic activities including oil spills, tanker operations, incomplete fossil fuel combustion and runoff. The sources and distribution of PAM`s in sediments are fairly well known, while the fate and transport of PAH`s in the marine environment are less known. Desorption is an important factor influencing the fate and transport of hydrophobic molecules at the seawater/sediment interface. The desorption of PAH`s from contaminated marine sediments to the water column/pore water affects the availability of the pollutant to biota. The sorption of PAH`s is determined in part by the organic carbon content of the sediments. The presence of ...

Energy Technology Data Exchange (ETDEWEB)

S-120 white oils are used to impregnate insulation and fill high voltage wires. Cooling oil flows of specified viscosities can increase the load capacity of wires. White oils are studied for viscosities and dielectric properties. To meet requirements, S-220 type oils of different medium or low viscosities are tested. Capacity can be increased by viscosity adjustment. Tests were also made to select optimum stabilizing additives to keep low-viscosity.

Energy Technology Data Exchange (ETDEWEB)

Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

Energy Technology Data Exchange (ETDEWEB)

General conclusions, principles and order of substantiating the extractable reserves and coefficients of oil extraction from oil and oil and gas fields are presented. Recommendations are made for solving questions of constructing calculation models for heterogeneous beds, schematization of the working conditions, selection of mathematical models for oil extraction for different geological-field conditions and different stages of ''life'' of the field.

International Nuclear Information System (INIS)

... amino acids ammonia biosynthesis cattle comparative evaluations diet

British Library Electronic Table of Contents (United Kingdom)

Abstract A one step method was used to prepare stable aqueous nanocomposite dispersions based on cellulose whiskers extracted from the rachis of the date palm tree and a poly(styrene co 2 ethyl hexylacrylate) copolymer via miniemulsion polymerization. A reactive silane, i.e., methacryloxypropyl triethoxysilane was added to stabilize the dispersion and favor the anchoring of the whiskers on polymer particles. Dynamic light scattering was used to study the effect of the silane and whiskers contents on the average particle size of the polymer. Nanocomposites materials were prepared from these dispersions using a casting/evaporation method. The effect of the silane and whiskers contents on the thermal and mechanical properties were studied using differential scanning calorimetry and dynamic me...

British Library Electronic Table of Contents (United Kingdom)

Date palm (Phoenix dactylifera) is widely cultivated in Kutch district of Gujarat and the fruits are harvested at immature stage before the onset of monsoon to prevent spoilage. The immature date fruits with less commercial value were used for processing into date juice concentrate. Immature dates were crushed and treated with 0.1% pectinase enzyme for 120 min to obtain maximum juice. Date juice was found to be rich in reducing sugars (16.1%) and total sugars (18.3%). Juice was pasteurized at 85?C to inactivate the enzyme, cooled and centrifuged at 3000 rpm to get clear juice. The juice was concentrated in a thin film evaporator to a total soluble solids (TSS) of 76?Brix in 2 passes. Chemical composition of date juice during different stages of concentration was determined. Date juice conc...

International Nuclear Information System (INIS)

A spreadsheet-based decision support system has been developed that allows easy evaluation of integrated biomass to electricity and biomass to ethanol systems. The Bioenergy Assessment Model (BEAM) has been developed to allow the techno-economic assessment of biomass to electricity and biomass to ethanol schemes, including investigation of the interfacing issues. Technical and economic parameters can be assessed for a variety of feedstocks, conversion technologies and generating cycles. Production modules are currently available for biomass supply from short rotation coppice and conventional forestry relevant to conditions and practices in NW Europe. The biomass conversion modules include pre-treatment (reception, storage, handling, comminution, screening and drying); atmospheric gasification (generic gasifier, wet gas scrubbing, dual fuel engine); pressure gasification (generic gasifier, hot gas filtration, gas turbine combined cycle); fast pyrolysis for liquid ...

Science.gov (United States)

Apr 25, 2010... oil per day were leaking from an oil well in the Gulf of Mexico in late April, following an explosion at an offshore drilling rig on April 20, 2010. ...

Energy Technology Data Exchange (ETDEWEB)

The future lubricants could be vegetable oils in order to replace the petroleum products. Vegetable oils are biodegradable and inoffensive for environment and for people. The main uses of vegetable oils are indicated. (O.L.). 3 refs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

Vegetable oils such as soybean oil will be converted to novel polymers using hydroformylation and other catalytic processes. These polymers can be used in the construction, automotive, packaging, and electronic sectors.

Energy Technology Data Exchange (ETDEWEB)

The adsorption interaction of different types of demulsifiers and the oils of Western Siberia is covered. The high adsorption capacity of Separol-5084 and disolvan-4490 reagents is established. The positive role of this phenomen in breaking aqueous oil emulsifiers is theoretically substantiated and experimentally confined.

Energy Technology Data Exchange (ETDEWEB)

The oil shale PCTM for Modified In Situ Oil Shale Retorting combined with Lurgi Surface Retorting addresses the application of this combination of technologies to the development of oil shale resources in the western United States. This manual describes the combined plant using Lurgi surface retorting technology (developed by Lurgi Kohle and Mineralotechnik GmbH, West Germany) and the Modified In Situ process (developed by Occidental Oil Shale, Inc.) proposed by Occidental Oil Shale, Inc. and Tenneco Shale Oil Company for use in the development of their Federal oil shale lease Tract C-b in western Colorado. Since details regarding waste streams and control technologies for the Lurgi process are presented in a separate PCTM, this document focuses principally on the Modified In Situ process.

Energy Technology Data Exchange (ETDEWEB)

Oil shale occurrences have been historically reported in the Cape Breton Island, northern mainland and southern mainland areas of Nova Scotia. Twelve of these occurrences were investigated for this study. Rocks from three of the areas gave oil yields of less than 25 litres per tonne (below oil shale grade) while the remainder gave oil yields greater than 25 litres per tonne (above oil shale grade). The rock types of oil shale grade include silicate-rich shale, carbonaceous shale locally transitional to coal, limy shale and petroliferous limestone associated with coal, silicate-rich shale and cannel shale associated with coal and silicate-rich shale, cannel shale and boghead shale associated with coal. The Stellarton Basin represents the province's largest oil shale resource with an estimated 825 x 10{sup 6} tonnes of ...

Science.gov (United States)

Phytoremediation has been identified as a potentially environmentally friendly and cost effective technique for the treatment of contaminated soil. However, phytoremediation has an unknown mechanism. In this study, we focus on the effects of the cultivation of Italian ryegrass on the soil microbes collected at oil showings, which were expected to have a variety of crude oil degradable microorganisms. We evaluated the number of crude oil degradable microorganism, microbial activity, microflora using the PCR-DGGE method and the change in the concentration of crude oil in the soil. The results indicated that the microflora was affected by the cultivation of Itarian ryegrass, and that the microbial activity and the number of crude oil degradable microorganisms were also improved by the cultivation. Moreover, the concentration of crude oil in the rhizosphere soil ...

International Nuclear Information System (INIS)

... organic compounds other organic compounds separation processes

Energy Technology Data Exchange (ETDEWEB)

The shallow Green River Formation oil shales in the southern part of Utah's Uinta Basin are potentially developable by strip mining or by subsurface techniques which take advantage of limited overburden. The resource of potential shale oil represented by the shallow deposits is evaluated in detail from corehole oil-yield data. Cross-sections are constructed to readily correlatable stratigraphic units selected to represent resources in the shallow shale. To define each unit, the thickness, average oil yield, and oil resource of each unit in each core are calculated. Contour maps constructed from these data define the resource variation across the shallow resource. By measuring areas enclosed in each resource unit within the defined limit of 200 feet (61 meters) of overburden, the resource represented by the shallow oil shale is evaluated. The total ...

UK PubMed Central (United Kingdom)

AIM: To search the independent factors determining gastric juice acidity and to investigate the acidity of gastric juices in various benign and malignant upper gastrointestinal diseases.METHODS:...Full Text Available

UK PubMed Central (United Kingdom)

Boric acid poisoning in 11 infants, occurring in the newborn nursery as a result of the accidental and inadvertent use of 2.5% boric acid in the preparation of the formulae, is reported. Five of the...Full Text Available

Science.gov (United States)

PMID:20113698

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The invention deals with a pumping plant for oil filled power cables. An air driven piston type pump is used as primary pump. A PLS (Programmable Logic control System) is used to control the oil flow to the cable(s). Improvements of the pump includes means for ensuring that the pump piston is operated also at low pressure and flow, and means for sealing off the piston rod to ensure maximum life of seals, to facilitate detection of possible leakages and to avoid contamination of the cable oil. 3 figs.

Energy Technology Data Exchange (ETDEWEB)

This document contains the outline and viewgraphs used in the speech. Topics covered are: conventional oil and gas recovery; unconventional oil and gas sources; oil shale resources; conventional coal combustion; advanced fossil power systems; fluidized bed combustion; coal/oil or coal/water mixtures; and gaseous and liquid fuels from coal. (DMC)

Science.gov (United States)

... Marine transport and oil disposal by boats and Matadi pose threats in the region. When the water ... ...

Science.gov (United States)

... PRODUCTION OF TIGHT OIL-GAS BEARING ROCKS, AND IS ALSO EMPLOYED FOR THE DEVELOPMENT OF GEOTHERMAL RESERVOIRS. ...

International Science & Technology Center (ISTC)

Isolation and Identification of Mycoplasmas, Development of Reliable Antigen for Mycoplasmas Detection and Oil-Based Vaccines

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... is Jin Ho Ocean Enterprise Co., Ltd., a Taiwanese business incorporated in 1985. Under the U.S. Oil ... ...

Energy Technology Data Exchange (ETDEWEB)

The increasing scarcity of conventional crude oil resources, as well as the sharply higher prices of crude oil, will generate increased interest in heavy oil, tar sands, and oil shale as potential substitutes. For all of these unconventional oil resources, extraction will be much more difficult, time consuming, and costly than for conventional crude oil. Although the inplace resources are vast and exist in many areas including the United States, the USSR, western Europe, Canada, and Latin America, probably only a small fraction of the inplace resources will prove to be economically extractable. These unconventional oil resources are now being developed in several locations around the world, and depending upon the exact definition probably account for less than 1 percent of current world oil supplies. The major current ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The Western Research Institute plan for addressing oil shale plant siting methodology calls for identifying the available resources such as oil shale, water, topography and transportation, and human resources. Restrictions on development are addressed: land ownership, land use, water rights, environment, socioeconomics, culture, health and safety, and other institutional restrictions. Descriptions of the technologies for development of oil shale resources are included. The impacts of oil shale development on the environment, socioeconomic structure, water availability, and other conditions are discussed. Finally, the Western Research Institute plan proposes to integrate these topics to develop a flow chart for oil shale plant siting. Western Research Institute has (1) identified relative topics for shale oil plant siting, (2) surveyed both published and ...

Energy Technology Data Exchange (ETDEWEB)

The primary objective of this study is to assess the oil and gas potential of the West Siberian Basin of Russia. The study does not analyze the costs or technology necessary to achieve the estimates of the ultimate recoverable oil and gas. This study uses reservoir data to estimate recoverable oil and gas quantities which were aggregated to the field level. Field totals were summed to a basin total for discovered fields. An estimate of undiscovered oil and gas, from work of the US Geological Survey (USGS), was added to give a total basin resource volume. Recent production decline points out Russia`s need to continue development of its discovered recoverable oil and gas. Continued exploration is required to discover additional oil and gas that remains undiscovered in the basin.

Energy Technology Data Exchange (ETDEWEB)

Manufacturers may be required to design transformers to overload specifications. Oil viscosity changes and loss variation with temperature are not accounted for in the industry loading guide. A comprehensive test program was performed using a winding assembly with imbedded thermocouples. Steady state and transient tests were performed for natural and non-directed forced oil circulation. The temperature distribution in the winding was not linear with height as usually assumed. A large number of temperature sensors is required to determine the hot spot location. The location of the hot spot was found to be different and less predictable for natural oil circulation compared with non-directed forced oil circulation especially during overload conditions. This paper reports that improved loading guide equations were developed to account for oil viscosity, resistance change, cooling duct ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Short communication.

J-STORE (Japan)

Full Text Available

UK PubMed Central (United Kingdom)

A field experiment was conducted during the summer of 1988 to test the hypothesis that water deficit affects the abscisic acid (ABA) and indole acetic acid (IAA) concentrations in cotton (Gossypium...Full Text Available

Science.gov (United States)

PMID:19469866

UK PubMed Central (United Kingdom)

Amino acid transport was studied in membrane vesicles of the thermophilic anaerobic bacterium Clostridium fervidus. Neutral, acidic, and basic as well as aromatic amino acids were transported at 40...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Because of its high price, the extra virgin olive oil is frequently target for adulteration with lower quality oils. This paper presents an innovative optical technique capable of quantifying the adulteration of extra virgin olive oil caused by lowergrade olive oils. It relies on spectral fingerprinting the test liquid by means of diffuse-light absorption spectroscopy carried out by optical fiber technology in the wide 400-1700 nm spectral range. Then, a smart multivariate processing of spectroscopic data is applied for immediate prediction of adulterant concentration.

Energy Technology Data Exchange (ETDEWEB)

Morocco is among the world's leading countries in terms of total indigenous oil shale resources. Following the 1973 oil crisis, Morocco has been determined to develop its oil shale energy resources. In the subsequent years following the crisis, a tremendous number and variety of studies and research efforts have resulted in an enormous amount of data, covering geological, hydrogeological, mining, physical and chemical aspects of the two main deposits, Timahdit and Tarfaya. This article represents a tentative analysis of oil shale development in Morocco and offers a few ideas on where it might be heading. 1 fig., 2 photos.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The study to get some fundamental materials was carried out, aiming at the recovery of valuable components from red mud produced in the bauxite processing. Acid leaching of red mud was used to clarify the effect of leaching time, leaching temperature and acid concentration on the recovery. The used acids were hydrochloric acid, sulfuric acid and nitric acid of which concentrations were 1.45, 1.8 and 1.2mol-l; the temperature was 25, 40 and 60 centigrade; and the time was 1, 2, 4 and 8 hours. Al in red mud was leached by all acids, became the equilibrium after 10 minutes, and was independent og the temperature and the leaching rate was about 70%. When the acid concentration was raised to two time for sulfuric acid and hydrochloric acid, the leaching rate increased by 15%. Si ...

Energy Technology Data Exchange (ETDEWEB)

The authors developed an analytical model (intersection model) to estimate the exposure of sea otters (Enhydra lutris), to oil from the Exxon Valdez oil spill. The authors applied estimated and assumed exposure dependent mortality rates to the Kenai Peninsula sea otter population to provide examples of the application of the model in estimating sea otter mortality. The intersection model requires three distinct types of data: (1) distribution, abundance, and movements of oil, (2) abundance and distribution of sea otters, and (3) sea otter mortality rates relative to oil exposure. Initial output of the model is an estimate of exposure of otters to oil. Exposure is measured in amount and duration of oil near an otter`s observed location (intersections). The authors provide two examples of the model using different assumptions about the relation between exposure ...

Energy Technology Data Exchange (ETDEWEB)

This study determined how well crude and fuel oils burn on water. Objectives were: (1) to measure the burning rates for several oils; (2) to determine whether adding heat improves the oils' combustibility; (3) to identify the conditions necessary to ignite fuels known to be difficult to ignite on ocean waters (e.g., diesel and Bunker C fuel oils); and (4) to evaluate the accuracy of an oil-burning model proposed by Thompson, Dawson, and Goodier (1979). Observations were made about how weathering and the thickness of the oil layer affect the combustion of crude and fuel oils. Nine oils commonly transported on the world's major waterways were tested. Burns were first conducted in Oklahoma under warm-weather conditions (approx. 30/sup 0/C) and later in Ohio under cold-weather conditions (approx. 0/sup 0/C ...

Energy Technology Data Exchange (ETDEWEB)

Cold Heavy Oil Production with Sand (CHOPS) is an enhanced oil recovery method that induces sand production to form a network of wormholes that increase the porosity and permeability of a formation. Under proper conditions, CHOPS can improve formation flow characteristics. Integrated well completion strategies that were used to increase oil production at Fula oil field on the south flank of Mughad Basin in Sudan were described. Limited sand influx provided a means for effective sand control while eliminating the need for conventional sand control processes. Cold heavy oil production with limited sand influx requires optimized completion methods to stimulate sand production, thereby reducing oil flow resistance and prolonging the sand removal operation cycle. Completion tests were performed in terms of different formation conditions including perforating ...

Energy Technology Data Exchange (ETDEWEB)

With regard to polybrominated diphenyl ether (PBDE), there is few scientific knowledge on the emission patterns into the environment and exposure pathways to humans, and basic information is insufficient to consider what measures effective are. For the purpose of promoting risk reduction of target substances more effectively and efficiently, it is desirable to comprehend accurately the causal chain from the target substances utilization to the risk intake, and to evaluate the measures covering the whole applications of target substances. As the existing researches on the PBDE emission inventory, there are EU risk assessment report (European Chemical Bureau 2000, 2002, 2003), Danish EPA (1999), Palm et al.(2002) and Alcock et al. (2003). In addition, emissions of DecaBDE are published in TRI (Toxic Release Inventory) of US EPA. However, the primary information of the previous inventories is often the same and estimations based on the measured values are few. In ...

Energy Technology Data Exchange (ETDEWEB)

Beginning in 1972 low-pressure cables filled with MN-4 oil produced by the Yaroslav Petroleum Processing Plant arrived at the Leningrad Cable Network of the Leningrad Rayon Power Administration. Lines formed with these cables have been successfully used. The parameters of the oil in them have not changed with respect to the values present when the lines were placed in operation. However, from here on filling in of the 110 to 220 kV input lines of low and high pressure will be accomplished with MN-4 oil produced by the Gorkiy Petroleum Processing Plant. Because petroleum from various fields and the properties of the oil produced from it are unlike, samples were taken from some elements of the lines filled in with MN-4 oil. The results of the tests are described.

International Nuclear Information System (INIS)

Experimentally, a feasibility study for adsorption and catalytic pyrolysis of spill oils on Cu/ZSM-5 for recycling of light oils has been conducted in the present work. The adsorption and pyrolysis of model compounds such as heptane, toluene, and diesel (to stimulate the spill oils) on Cu/ZSM-5 have been investigated on a continuous fixed-bed reactor. By component fitted X-ray absorption near edge structural (XANES) spectroscopy, catalytic active species such as metallic copper (Cu) (77-84%) and Cu2O (6-7%) are found in the channels of ZSM-5 during pyrolysis of heptane or toluene. Pyrolysis of diesel effected by Cu/ZSM-5 yields gas (C1-C5) (32%) and light oil (68%) that can be used as auxiliary fuels.

Energy Technology Data Exchange (ETDEWEB)

The Carter Administration has set a synfuels goal of 1.5 million bopd by the year 1990, with shale oil to furnish 400,000 bpd. Presumably most, if not all, of the shale oil production will be from the Eocene Green River formation that underlies large areas of northwest Colorado, northeast Utah, and southwest Wyoming. A major part of the oil shale resources of the Green River formation occurs in the Piceance Creek basin of Colorado. Where is the available resource base, and what is the possible interest of industry in developing the Green River oil shales. Project readiness in the Piceance Creek basin is reviewed, and projected production is estimated. International potential for development of oil shale reserves also is discussed.

Energy Technology Data Exchange (ETDEWEB)

Microbial enhanced oil recovery (MEOR) technology has advanced internationally since 1980 from a laboratory-based evaluation of microbial processes to field applications. In order to adequately support the decline in oil production in certain areas, research on cost-effective technologies such as microbial enhanced oil recovery processes must focus on both near-term and long-term applications. Many marginal wells are desperately in need of an inexpensive improved oil recovery technology today that can assist producers in order to prevent their abandonment. Microbial enhanced waterflooding technology has also been shown to be an economically feasible technology in the United States. Complementary environmental research and development will also be required to address any potential environmental impacts of microbial processes. In 1995 at this conference, the goal is to further document and promote ...

Energy Technology Data Exchange (ETDEWEB)

Experiments were carried out to test the hypothesis that instantaneous daily rates of egg-larval mortality of Pacific herring were higher at two oil-exposed sites than at two other sites not so exposed. Results showed that egg-larval mortality was twice as great in the oil-exposed areas as in the two non-oiled areas. Larval growth rates were also severely affected; they were about half of those measured in populations from other areas of the north Pacific Ocean. A cautionary note was introduced to the effect that the differences in the egg-larval mortality between oiled and control sites may have been influenced by differences in egg dessication, predation, and wave scouring, hence these results should not be construed as conclusive evidence of oil spill damage. 40 refs., 6 figs.

British Library Electronic Table of Contents (United Kingdom)

Oils in Jinghu sag are abundant with high content of polar compounds and have a low ratio of saturate to aro-matic hydrocarbons and a high ratio of resin to asphaltene. The gross composition of oils in the Jinghu sag suggests typical immature to low mature characteristics. Some compounds with low thermal stability were identified. Light hy-drocarbons, a carbon preference index, an odd even index, n-alkane and hopane maturity parameters show mature fea-tures and little differences in the maturity level among oils. Sterane isomerization parameters indicate an immature to low mature status of oil. Transfer of the sedimentary center during sedimentation has led to different thermal histories among subsags and thus generated oils with different maturities. On the basis of source analyses, four ...

International Nuclear Information System (INIS)

We studied the effect of extracellular Ca"2"+ concentration ([Ca"2"+]_e) on adipocyte differentiation. Preadipocytes exposed to continuous [Ca"2"+]_e higher than 2.5 mmol/l accumulated little or no cytoplasmic lipid compared to controls in 1.8 mmol/l [Ca"2"+]_e. Differentiation was monitored by Oil Red O staining of cytoplasmic lipid and triglyceride assay of accumulated lipid, by RT-PCR analysis of adipogenic markers, and by the activity of glycerol-3-phosphate dehydrogenase (GPDH). Elevated [Ca"2"+]_e inhibited expression of peroxisome proliferator-activated receptor #gamma#, CCAAT/enhancer binding protein #alpha#, and steroid regulatory binding element protein. High [Ca"2"+]_e significantly inhibited differentiation marker expression including adipocyte fatty acid binding protein, and GPDH. The decrease in Pref-1 expression that accompanied differentiation also was prevented by high [Ca"2"+]_e. Treatment of 3T3-L1 cells with high [Ca"2"+]_e ...

Energy Technology Data Exchange (ETDEWEB)

The samples comprise the foliage of four pteridosperm-medullosalean plant fossil species of differing preservation states and one of a cordaitean species from two Canadian Maritime sub-basins of Carboniferous age (300 Ma; Sydney and Stellarton coalfields, Nova Scotia, respectively). Included in the sample set were some coal samples from Sydney Coalfield, along with published data for coal macerals for comparison. By applying Schulze's maceration process to the fossil foliage to obtain the cuticles, five sample forms evolved, viz. compressions, cuticles and fossilized cuticles, and acidic and alkaline solutions from Schulze's process, to which was added the Sydney coal samples as the sixth form. Area integration of the absorbance spectra from solid and liquid state Fourier transform infrared (FTIR) spectroscopy, produced functional chemical parameters which were organized into a data matrix of eight variables and 62 samples (8 x 62 matrix). ...

International Nuclear Information System (INIS)

The attenuation of gamma rays in some fatty acids, viz. formic acid (CH_2O_2), acetic acid (C_2H_4O_2), propionic acid (C_3H_6O_2), butyric acid (C_4H_8O_2), n-hexanoic acid (C_6H_1_2O_2), n-caprylic acid (C_8H_1_6O_2), lauric acid (C_1_2H_2_4O_2), myristic acid (C_1_4H_2_8O_2), palmitic acid (C_1_6H_3_2O_2), oleic acid (C_1_8H_3_4O_2) and stearic acid (C_1_8H_3_6O_2), has been measured at the photon energies 81, 356, 511, 662, 1173 and 1332 keV. Experimental values for the molar extinction coefficient, the effective atomic number and the electron density have been derived and compared with theoretical calculations. There is good agreement between experiment and theory.

Energy Technology Data Exchange (ETDEWEB)

This research investigated the influence of stearic acid on the injection molding of alumina, by varying the concentration of stearic acid. The interaction between stearic acid and alumina was identified using transmission infrared spectroscopy, indicating stearic acid preferentially adsorbed onto the alumina powder surface. In addition to slightly modifying the intrinsic binder viscosity, stearic acid adsorbed onto the powder surface changed the flow behavior of the mixtures from dilatant flow to pseudoplastic flow at low temperatures. As a result, inhomogeneous distribution of binder in the injection-molded parts was minimized with increased stearic acid concentration. However, the possibility of forming bubbles in the mixtures arising from vaporization of stearic acid was enhanced. Additionally, the binder burnout temperature range was ...

Science.gov (United States)

This patent describes a method of improving the S0{sub 2} scrubbing efficiency of flue gas desulfurization scrubbers. It comprises conducting the scrubbing operation in such scrubbers in the presence of an oil-soluble surfactant.

Science.gov (United States)

Any student that has spent time in the kitchen knows that hot vegetable oil will pop and spatter violently after coming into contact with water such as that on the surface of foods (meat, fish, potatoes, etc.). This well-known effect can be used as an instructional resource to promote cooperative, active, and inquiry-based learning about central concepts of chemistry including boiling point, miscibility, and density of liquids. The starting point of the learning activity is a demonstration of (i) the effect of adding a drop of water to hot (as for cooking) vegetable oil and (ii) the effect of adding a drop of vegetable oil to hot water (near its boiling point). Intermolecular interactions, properties of vegetable oils, and a variety of other topics, such as the importance of other heat points (smoke, flash, and fire) for oils, the fundamental of the crackle test for checking the ...

Energy Technology Data Exchange (ETDEWEB)

A study was carried out to identify optimal laminate/oil combinations for low pressure oil filled and high pressure pipe-type cables, and to establish taping criteria under factory conditions. Laminates from two sources were evaluated in conjunction with Sun XX high viscosity mineral oil and Cosden 015SH polybutene oil for high pressure type cables, and Dussek TC-2288N mineral oil, Shell P2 dedecylbenzene and Chevron DF-100 alkylbenzene for low pressure oil-filled cables. Swelling tests, infrared analysis, dissipation and dielectric measurements, impulse tests and a taping trial were performed. It was found that there is no appreciable difference in performance of both laminates when tested on model cables in a variety of oils. Both types exhibited superior aging characteristics vis-a-vis cellulose paper when tested with a variety of ...

Energy Technology Data Exchange (ETDEWEB)

The technology being evaluated is the Modified In-Situ (MIS) retorting process for raw shale oil production, combined with a Circulating Fluidized Bed Combustor (CFBC), for the recovery of energy from the mined shale. (VC)

Energy Technology Data Exchange (ETDEWEB)

The conversion of coal to oil can be carried out in two ways. A synthesis route and a degradation route. Each of these routes are described and several degradation processes are explored. The testing of several fuels produced from coal is also given considerations.

Energy Technology Data Exchange (ETDEWEB)

A method is proposed for operating bed waters in an oil well by injecting silanes into the near-face zone. It is distinguished by the fact that in order to improve the effectiveness of insulation, the silanes used are silanes of general formula Si /SUB n/ H /SUB 2n-n/ .

Energy Technology Data Exchange (ETDEWEB)

The insulating oil used in a transformer is a critical component, as its service life is typically 20 years with possibly little or no maintenance. Partial discharges (PD), thermal overloads and static discharges continually subject the oil to chemical deterioration during its operating life. To ensure equipment reliability during service, it is important that the initial quality of the new insulating oil should meet the required acceptance specifications and preferably be pre-tested before use. Accelerated aging tests have been devised to determine the life expectancy of oil in service by using forced air or oxygen flow into the oil, the presence of a copper catalyst, and at elevated temperatures. The more important standards relating to transformer application are discussed and highlights of the more important aspects of the oxidation chemistry of hydrocarbons are included. The ...

Science.gov (United States)

... were given daily i.p. injections of either sesame oil (2.5 ml/kg, vehicle control) or VCD dissolved in sesame oil (80 mg/kg, 0.57 mmol/kg) for ... ...

Energy Technology Data Exchange (ETDEWEB)

Biodiesel is derived from triacylglycerides and is produced primarily through transesterification, a chemical reaction of vegetable oils with alcohol, methanol or ethanol. The cost of raw material should be considered since 85 per cent of production cost is related to vegetable oil. The purpose of this study was to evaluate oil expression of sunflower seed. It also examined the sunflower crude oil as a raw material for biodiesel by transesterification in both laboratory and pilot scale studies. Three different biodiesel purification methods were examined. The best result for oil expelling (68.4 per cent) at the experimental stage was obtained for seeds with a moisture content of 6.9 per cent at 25 degrees C and at a screw speed of 114 rpm. For biodiesel production at the laboratory scale, the best result for oil expelling was 87.5 per cent. It was obtained with ...

UK PubMed Central (United Kingdom)

1. The effect on rat liver peroxisomal beta-oxidation of feeding diets containing various amounts of dietary oils was investigated. With increasing amounts (5-25%, w/w) of soya-bean oil an apparent,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report describes research performed by the Morgantown Energy Technology Center in the following areas: oil and gas; advanced systems describing a coal solid fuel and an eastern shale oil residue waste program; environmental remediation; and waste management technologies.

Science.gov (United States)

...Amendments to Sections 8-2:704 (Use of Certain Fuel Oils Forbidden), 8-2:705 (Use of Certain Coal Forbidden...and Nitrogen Oxides. Section 801(Sulfur Content of Fuel Oils), subsection 801.1 Section 802(Sulfur...

UK PubMed Central (United Kingdom)

1. The fluorescent fatty acid probe 11-(dansylamino)undecanoic acid (DAUDA) binds with high affinity to bovine and human serum albumin (BSA and HSA) at three sites. 2. The Kd of the primary binding...Full Text Available

Science.gov (United States)

A study to define the effectiveness limits of sulfamic acid and to discover other better stabilizers for Pu(III) is described. Ascorbic and isoascorbic acids, used in conjunction with sulfamic acid reduced Pu(IV) to stable Pu(III) in nitric acid. Aminoguanidine sulfate also retarded the oxidation of Pu(III) but did not reduce Pu(IV). (J.R.D.)

Energy Technology Data Exchange (ETDEWEB)

Green River oil shale was air oxidized at subretorting temperatures. Off gases consisting of nitrogen, oxygen, carbon monoxide, carbon dioxide, and water were monitored and quantitatively determined. A mathematical model of the oxidation reactions based on a shrinking core model has been developed. This model incorporates the chemical reaction of oxygen and the organic material in the oil shale as well as the diffusivity of the oxygen into the shale particle. Diffusivity appears to be rate limiting for the oxidation. Arrhenius type equations, which include a term for oil shale grade, have been derived for both the chemical reaction and the diffusivity.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

The production and uses are described for extracellular microbial polysaccharides (generically called emulsans) and for a new class of extracellular microbial protein-associated lipopolysaccharides (collectively called alpha-emulsans) produced by Acinetobacter Sp. ATCC 31012, its mutants or recombinants. Also included are the deproteinized lipopolysaccharides (collectively called apoemulsans) obtained from such emulsans, as well as to the divalent metal, ammonium, and quaternary ammonium salts of such emulsans and apoemulsans. The materials can be used (1) in cleaning oil-contaminated vessels used to transport or store crude oil or petroleum fractions in such a manner that the residual oil may be recovered for fuel value or for refining and (2) in enhanced oil recovery.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The long term objective of the Oil Sands Business Unit of Alberta Energy is to pave the way for Alberta's bitumen production to reach 3 million barrels per day by 2020. This presentation described the national government's role in resource development. It was emphasized that since the Crown is the owner of the oil sands resource, it would benefit by providing strategic leadership and by generating a larger royalty base. The oil sands fiscal regime was described with reference to generic royalty, risk sharing, investment, and project economics. Business rule principles were also outlined along with criteria for project expansions. Both upstream and downstream challenges and opportunities were listed. 4 figs.

Energy Technology Data Exchange (ETDEWEB)

A research program has been undertaken to characterize oil sand deposits. Studies include delination of reservoir architecture; petrophysical attributes; and petrography and core analysis.

Energy Technology Data Exchange (ETDEWEB)

Exploration for oil shale in Queensland between June 1986 and July 1987 continued over 12 deposits ranging in age from Permian to Tertiary. The total estimated resource of shale oil contained within these deposits is 4479 GL (28.2 billion barrels). 4 refs., 1 fig., 1 tab.

International Nuclear Information System (INIS)

This work presents and describes the natural radioactive occurrence in oil facilities. The origins of the detected radioactivity and the reasons of its settlement are discussed. The measurements results carried out in oil facilities in the Neuquina basin (Argentine) are shown in this work. The aim is to describe the actual situation and to evaluate the magnitude of the problem. Finally, recommendations are proposed to protect the health of the workers, especially of those who carry out the cleaning of the equipment, and to guarantee an appropriate final disposal for the generated radioactive residuals. (author)

Energy Technology Data Exchange (ETDEWEB)

This paper reports the effectiveness of solvents on the liquefaction of 11 different Turkish lignites investigated by using tetralin, creosote, and anthracene oils. The highest total conversions were obtained with tetralin. The catalytic effects of CoMo and red mud were compared by using creosote oil as the solvent. It was found that red mud catalyzed mainly the asphaltene formation reaction for the given experimental conditions. The additional of CoMo significantly catalyzed the liquefaction reaction, thus increasing the lignite conversion and oil formation.

UK PubMed Central (United Kingdom)

When autotrophically growing cultures of Chlorella are treated with levulinic acid, δ-aminolevulinic acid is excreted into the medium, providing a direct demonstration of α-aminolevulinic...Full Text Available

UK PubMed Central (United Kingdom)

IntroductionAcute lung injury (ALI) may arise both after sepsis and non-septic inflammatory conditions and is often associated with the release of fatty acids, including oleic acid...Full Text Available