Two additional hyperfine components of the interstellar radical C3H were detected. In addition, methanol was discovered in interstellar clouds. The abundance of HCCN and various chemical isomers in molecular clouds was investigated.
The composition, rank, coal facies, and coal pore structure characteristics of 15 coal samples were investigated systemically using methods of lithotype analysis, maceral analysis, proximate analysis, mercury porosimetry analysis, and nitrogen adsorption analysis. These samples were directly collected from the working faces of No.4, 8, 9 seams in Liulin district, eastern margin Ordos Basin, China. Four types of paleoenvironment including a wet forest swamp, an intergradation forest swamp, a drained forest swamp, and a fresh-water peat swamp were distinguished by lithotype and merceral analysis. An R-cluster analysis was performed to demonstrate the correlations between the coal facies and the pore structures. The results showed that coal rank is the primary factor affecting the development of micropores and transition pores, whereas coal facies control the development of seepage pores in similar coalification conditions, especially in a local district and in a ...
The Gulf of California represents one of the most productive and unique marginal seas in the world. The mouth of the Gulf captures warm equatorial water while annual wind patterns assure major upwelling of nutrient-rich water leading to a rich marine biota. These conditions have created a wide array of tropical through warm temperate carbonate environments. The most unusual of these environments is located in the La Paz region of Baja California Sur where tropical-subtropical water temperatures and low rainfall have allowed growth of corals, calcareous red algae, and other shelled invertebrates to form a carbonate bank environment. Sampling and mapping transacts in shallow bays north of La Paz and on the adjacent Espiritu Santo island have revealed a full spectrum of subenvironments including mangrove bordered, terrigenous mud dominated coastal zones, which grade into carbonate tidal flats. In addition, single coral heads as well as incipient reef structures constructed by Porites and ...
Performance and operating characteristics are presented for a solar powered aircraft intended to remain aloft for long periods. The critical technologies which limit the performance are identified. By using the techniques presented, the effects of variation in the system parameters are studied. Practical design consideration are discussed.
Due to changed operational conditions and because of the increasing age of several hydro power plant components, there is an increasing risk of damages and the control of degradation mechanisms is of increasing significance. Therefore lifetime considerations for safety relevant components in pumped-storage plants become more and more important. The development of a lifetime management system, in conjunction with monitoring systems and specific surveillance for a group of pumped-storage power plants of different ages and in a wide range of power output is presented. The special focus is on the impact of fatigue strength considerations within this framework. The applied procedure will be described for typical mechanical components in pumped-storage plants exemplarily. (orig.)
The purpose of the chapter is to explain briefly the various considerations that enter into determining the general layout or arrangement of typical hydroelectric powerplants, pumping plants, and pumped-storage plants. Some of the important factors that affect or determine the location, type, and layout of the plant and the selection of the major items of equipment included in the installation are outlined in this chapter. The first consideration in the design of a powerplant, pumping plant, or pumped-storage plant is that it adequately perform its function and be structurally safe. The structure is also designed to give a pleasing architectural appearance.
This article describes the disenchantment with electric cars after considerable hype by industry. Also discussed is why electric cars have failed to catch on.
The interaction between two metals, which can be either synergistic or antagonistic, implies that the behavior of one is changed by the presence of the other. Possible mechanisms of these interactions,...Full Text Available
In the last two decades rectal cancer has changed from a surgically managed disease into a multidisciplinary treatment model resulting in considerable improvements in the survival and outcome. This...Full Text Available
There is considerable evidence that purines are vasoactive molecules involved in the regulation of blood flow. Adenosine is a well known vasodilator that also acts as a modulator of the response to...Full Text Available
The early and precise diagnosis, the prognosis, and the clinical management of multiple sclerosis, remain a considerable challenge. In recent years, the development of novel and powerful proteomic...Full Text Available
Rationale and ObjectivesSample-size estimation is an important consideration when planning a receiver operating characteristic (ROC) study. The aim of this work was...Full Text Available
The concept of plant intelligence, as proposed by Anthony Trewavas, has raised considerable discussion. However, plant intelligence remains loosely defined; often it is either perceived as practically...Full Text Available
your eye to the SCN in your brain, so that light ... Owls are individuals who go to bed late, like to get up late in the moming. And the moming types, ...
Mice are an ideal mammalian model for studying the genetics of aging: considerable resources are available, the generation time is short, and the environment can be easily controlled, an important...Full Text Available
Since the elucidation of the structure of double helical DNA, the construction of small molecules that recognize and react at specific DNA sites has been an area of considerable interest. In...Full Text Available
There is considerable evidence to suggest that the identification and treatment of dyslipidaemia will reduce the risk of premature CHD, i.e. before the age of 65. Diagnosis of the cause of raised plasma...Full Text Available
There is considerable interest in the use of silicon devices as qubits for quantum computing. The existence of nuclear spin in a silicon isotope and the complex band structure of silicon are unfavourable for this application of silicon devices. (viewpoint)
Numerous reports of chronic renal disease in patients who habitually use phenacetin-containing compounds to excess have aroused considerable controversy over the possible relationship between phenacetin,...Full Text Available
... to de-scope the weapon system. ... AIAA American Institute of Aeronautics and Astronomy ... Nations BASIC Broad Area Space-Based Imagery Collector ...
In animal models, single-gene mutations in genes involved in insulin/IGF and target of rapamycin signalling pathways extend lifespan to a considerable extent. The genetic, genomic and epigenetic influences...Full Text Available
... Thus. thi, characteristic further buggeots, other things unchanging, that the more *multifunction" the ccna ;Ituent devices ari., t~he more efficienit the ...
The fatigue and fracture behavior of hard tissues are topics of considerable interest today. This special group of organic materials comprises the highly mineralized and load-bearing tissues...Full Text Available
Immunomodulation by environmental chemical contaminants and the role immune parameters play in toxicity and risk assessment studies is of increasing concern. Although considerable evidence has indicated...Full Text Available
A modest reduction in body temperature prolongs longevity and possibly retards aging in both poikilotherm and homeotherm animals. Some of the possible mechanisms mediating these effects are...Full Text Available
Recommendations of the Advisory Committee on Reactor Safeguards are presented to the Commissioners for their consideration for FY 82 budget for the NRC safety research program.
Recommendations of the Advisory Committee on Reactor Safeguards are presented to the Commissioners for their consideration for FY 83 budget for the NRC safety research program.
Breast cancer in the elderly has attracted considerable interest in recent years for three main reasons. Firstly, information concerning the profile (clinical and biological) of the disease in the geriatric...Full Text Available
Central airway obstruction (CAO) is a serious presentation of lung cancer and associated chest diseases. It presents a real challenge to the anesthesiologist because usually the patient admitted to...Full Text Available
In several respects the dorsal thalamus of Trichosurus presents a level of organizational complexity considerably in advance of that seen in Didelphis. In particular, such features as the lamination...Full Text Available
Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.
Information is presented concerning new trends in licensing; seismic considerations and system structural behavior; TMI-2 risk assessment and thermal hydraulics; statistical assessment of potential accidents and verification of computational methods; issues with respect to improved safety; human factors in nuclear power plant operation; diagnostics and activities in support of recovery; LOCA transient analysis; unresolved safety issues and other safety considerations; and fission product transport.
The use of computer vision to detect, measure, and perhaps guide the assembly of man-made components is potentially a very significant research and development area. The efficacy of these techniques for any given application depends on both technical and economic considerations. This paper will explore both these considerations using appropriate generic examples. It is our goal to first present a concise discussion of the present state of many technical and economic factors and then extrapolate these factors into the future for the purpose of guiding further investigations.
This article illustrates what typical accept/reject curves might look like and discusses progress made in developing the required inspection techniques for flaw dimensioning. Consideration is given to the relative significance of blunt versus planar types of flaws, and of inherent limitations to the depths of certain types of flaws. Finally, consideration is given to the realities of implementing proposed procedures under field conditions. These are summarized in a series of technical options for implementation of program results.
The performance of a commercial heat pipe was investigated both experimentally and theoretically. The effect of the temperature difference, the surface area ratio, and the operational conditions on the performance were studied. The heat flow rate and the vapor temperature were estimated on a ready-made commercial heat pipe. Its performance varied considerably with operational conditions. Theoretical consideration of a mathematical model and several nomographs are also presented. This work is applicable to the design and use of heat pipes in the field.
ObjectiveAnimal feeding practices in the United States have changed considerably over the past century. As large-scale, concentrated production methods have become the predominant...Full Text Available
...qualified and who were under consideration at the time, USDA Secretary Tom Vilsack chose an animal husbandry specialist employed by one of the largest organic livestock product marketers in the country. While this appointee had grown up on a conventional farm, her immediate occupation is not that of ...
This revision of the APT Waste Management Plan details the waste management requirements and issues specific to the APT plant for design considerations, construction, and operation. The APT Waste Management Plan is by its nature a living document and will be reviewed at least annually and revised as required.
Albeit the considerable progress that has been made both in our understanding of the pathophysiology of acute renal failure (ARF) and in its treatment (continuous renal replacement therapies), the morbidity...Full Text Available
Reliable dietary assessment is a challenging yet essential task for determining general health. Existing efforts are manual, require considerable effort, and are prone to underestimation and misrepresentation...Full Text Available
The dwelling is equipped with solar collectors which heat the air circulating in the cavity walls and the space beneath the floors. The thermal aspects of such a building are described. Heat balance, losses, heating by the sun in different seasons are described. Different measures taken to reduce the energy losses are described.
BackgroundWhile physical health has improved considerably over recent decades in Finland, the disease burden of mental health, especially that of depression, has become increasingly...Full Text Available
BackgroundPlasmodium falciparum morbid and fatal risks are considerably higher in areas supporting parasite prevalence ≥25%, when compared with low transmission...Full Text Available
BackgroundPrevious studies in Ascomycetes have shown that the function of gene families of which the size is considerably larger in extant pathogens than in non-pathogens could be...Full Text Available
BackgroundThere has been considerable effort to discover plant-derived antibacterials against methicillin-resistant strains of Staphylococcus aureus (MRSA) which...Full Text Available
Analysis of the pulsed-field gel electrophoretic profiles of 82 pneumococcal isolates with reduced susceptibility to ciprofloxacin (RSC) and of 90 co-occurring susceptible isolates indicates a considerable...Full Text Available
BACKGROUND: Patients with shoulder disorders are believed to benefit considerably from steroid injections. However, the controversy about their efficacy persists. AIM: The study was designed to assess...Full Text Available
Chemicals having a capacity to disturb the endocrine system have attracted considerable interest during recent years. There is a shortage of well-characterized in vivo tests with which to study such...Full Text Available
The planned spallation source can be of considerable significance for biomedical basic research and for clinically relevant diagnostic and therapeutic applications. The following gives a brief description and explanations for its possible use in clinical medicine: I. Treatment of Malignant Tumors II. Production of Isotopes for Biochemical Investigations in Living Organisms for Diagnostic Purposes.
Subjects covered in this section are: (1) PCAST panel promotes energy research cooperation; (2) Letter issued by ANS urges funding balance in FFTF restart consideration and (3) FESAC panel releases report on priorities and balance.
Less wind power plants in the landscape, more power from renewables, less carbon dioxide and higher tax: The advantages of repowering for communities are considerable. Still, they are hesitant to use it. (orig.)
This report presents geologic considerations that are pertinent to the Remedial Action Plan for Slick Rock mill tailings. Topics covered include regional geology, site geology, geologic stability, and geologic suitability.
1. In rat soleus muscle, high frequency electrical stimulation produced a rapid increase in intracellular Na+ (Na+i) content. This was considerably larger in muscles contracting without developing tension...Full Text Available
The paper reviews the main observational data on pulsars, both the individual characteristics of pulsars and the properties they possess as members of the Galaxy. Consideration is then given to pulsar ages and to pulsar initial periods. An attempt is made to clarify the 'true' ages of pulsars.
BackgroundIrritable bowel syndrome (IBS) and functional dyspepsia (FD) show considerable overlap and are both associated with psychiatric comorbidity. The present study aimed to...Full Text Available
The current obesity pandemic is expected to result in considerable downstream morbidity, mortality and incremental costs to health care systems around the world. The major metabolic complications of...Full Text Available
Military working dogs are rapidly becoming integral to military operations. While they bring many valuable capabilities to the battlefield, it is important that Special Operations leaders consider canine team capabilities and requirements when planning mi...
BackgroundDespite considerable efforts to promote and support guideline use, adherence is often suboptimal. Barriers to adherence vary not only across guidelines but also across...Full Text Available
BackgroundSeasonal influenza A infection affects a significant cohort of the global population annually, resulting in considerable morbidity and mortality. Therapeutic strategies...Full Text Available
Importance of the fieldThe cytochrome P450 (CYP) isoforms that are selectively induced following exposure to structurally-diverse chemicals often are the ones capable...Full Text Available
The conversion of coal to oil can be carried out in two ways. A synthesis route and a degradation route. Each of these routes are described and several degradation processes are explored. The testing of several fuels produced from coal is also given considerations.
BackgroundAlthough considerable progress has been made in the treatment of chronic kidney disease, compromised quality of life continues to be a significant problem for patients...Full Text Available
for an Air Force Manufacturing technology program whose aim is the establishment of organic matrix ...... display considerations for advanced energy/flight management sys- ...... Future System - The Roadmap of the System of the Future - ...... data storage units, pilot's guidance indicators, and a quick look ...
Several compact proton accelerator systems for use in proton therapy have recently been proposed. Of paramount importance to the development of such an accelerator system is the maximum kinetic energy...Full Text Available
Localized mRNA provides spatial and temporal protein expression essential to cell development and physiology. To explore the mechanisms involved, considerable effort has been spent in establishing new...Full Text Available
Dyslexia (or reading disability) and specific language impairment (or SLI) are common childhood disorders that show considerable co-morbidity and diagnostic overlaps and have been suggested to share...Full Text Available
A series of N-alkylamide epoxides have shown considerable selective activity against insects. The N-ethyl and 7,11-dichloro-N-ethyl derivatives showed particularly pronounced activity, and this paper...Full Text Available
Beamline VI is a wiggler-based, multi-kilowatt, intense synchrotron radiation beamline installed SPEAR. The thermal design parameters for this beamline are presented and then design considerations and construction descriptions are given for many of the high-power photon beamline elements.
Harmful algal blooms, caused by rapid growth and accumulation of certain microalgae in the ocean, pose considerable impacts on marine environments, aquatic industries and even public health. Here, we...Full Text Available
The clinical significance, Gram stain reaction, and genus affiliation of Gardnerella vaginalis have been controversial since Gardner and Dukes described the organism as the cause of "nonspecific vaginitis,"...Full Text Available
This study explored posttraumatic growth (PTG), positive change resulting from struggling with trauma, among 7- to 10-year-olds impacted by Hurricane Katrina. Analyses focused on child self-system...Full Text Available
Environmental health concerns in the Persian Gulf are peculiar to the geography of the region. Prevention of heat and solar injury deserves primary consideration, but cold injury also may occur in the...Full Text Available
When choosing an electromagnetic tracking system (EMTS) for image-guided procedures several factors must be taken into consideration. Among others these include the system’s refresh rate, the...Full Text Available
A rapid expansion of urban systems, particularly in less-developed countries, pose considerable challenges. Urbanization also provides opportunities for socio-economic progress. Relative contribution...Full Text Available
In order to decrease tritium exposure to workers, the ratio of which is up to 40% of total exposure, tritium removal facility is getting to be one of the considerable parameters in Korea, due to the next CANDUs to be operated at Wolsung NPP. For investiga...
This investigation clearly demonstrates that through partial impregnation techniques wood-polymer composites can be formed from the Pinus species grown in South Africa with a considerable saving in monomer costs without sacrificing the important physical properties of these materials.
BackgroundEffective prevention of excessive alcohol use has the potential to reduce the public burden of disease considerably. We investigated the cost-effectiveness of Screening...Full Text Available
Finland has set up several national air pollution control programmes in order to implement international conventions. As a rule these programmes have focused on one pollutant. The national second carbon dioxide commission is at present working on a new programme to curb carbon dioxide emissions, and this will unavoidably affect other programmes, too. This study presents the existing programmes and their respective implementation costs. The aim has been to focus on the interaction between different air pollution combatting measures and the possibilities of setting priorities on a cost basis. The main result is that it will be difficult to integrate overall aims for general welfare and subsequent energy consumption with environmental considerations, especially in air pollution control. If the increase in energy generation follows current scenarios, the costs for air pollution abatement measures will require a considerable portion of the increase ...
The use of mice for the assay of tetanus toxoids would offer considerable advantages over the use of guinea-pigs, but mice cannot readily be immunized with the fluid tetanus toxoid at present designated...Full Text Available
Requirements for food packaging materials include whether there is any interaction between the food and the package during or after the irradiation, and whether as a result of the irradiation, volatile or leachable substances are released from the pack into the food. The performance of cellulose-based materials and plastic films under irradiation are discussed.
The main problems encountered during the operation of horizontal steam generators are considered. Design features of the new PGV-1000MK and PGV-1500 steam generators are analyzed.
BackgroundVariable platelet response to clopidogrel has been widely observed. Studies have shown that the mean aggregation response to clopidogrel can be changed...Full Text Available
Following a brief description of the SSC, the computing needs are discussed for both the accelerator design and the experimentation. The computing power required is considerably beyond that being used at present facilities, and parallel processing is expected to play an important role in supplying these needs.
Type 2 diabetes mellitus (DM2) is increasing in incidence, creating worldwide public health concerns and impacting morbidity and mortality rates. An increasing number of studies have demonstrated shared...Full Text Available
Patients do considerable information work. Technologies that help patients manage health information so they can play active roles in their health-care, such as personal health records, provide...Full Text Available
The different radiation loads caused by natural and artificial radionuclides are compared in this paper. This examples will serve to illustrate that the problem of population exposure to radiation can only be solved in consideration of all components and to show which effects of the radiation from natural sources are of special importance in this connexion. (orig./AK).
Currently there is considerable interest among oncologists to find anticancer drugs in Chinese herbal medicine (CHM). In the past, clinical data showed that some herbs possessed anticancer properties,...Full Text Available
Transgenic mouse models have contributed considerably to our understanding of the cellular and molecular mechanisms by which androgens control spermatogenesis. Cell-selective ablation of the androgen...Full Text Available
... relative suitability of areas for production of commercial timber was determined based on considerations of operability, proximity ... habitats, and an ecologically-based estimate of sustainable timber pr...
Accurate segmentation of tissue microarrays is a challenging topic because of some of the similarities exhibited by normal tissue and tumor regions. Processing speed is another consideration...Full Text Available
The power industry is undergoing major changes. Deregulation and a competitive climate demand effective solutions. Costs and losses must be reduced, and overall efficiency must be raised. Industrial options connected to energy market and environmental considerations are discussed. Themes discussed in this paper are environmental challenges, the fuel factor, power plants in use today, the Norwegian power system, the European system, power exchange across borders, the transmission system, the future European system, and options for Norwegian industry. 27 figs.
The short range of low-energy electrons has made them suitable for the treatment of skin lesions, especially when extensive areas must be irradiated with special considerations to save the normal underlying tissue. This report covers some salient features of total body electron irradiation: the construction of the large fields required, x-ray contamination levels, and multiple-field techniques. While the investigation is essentially experimental, we also indicate the results of calculations. We conclude most generally that treatment planning with whole skin irradiations can be as precise as with smaller fields.
Much as it is accepted for pollution control reasons air pollution abatement still is the subject of heated debates. Pollutant emissions can considerably be reduced with the help of electric power supplies. In order not to prejudice electric power users tariffs have to be adapted to the prices of other energy sources available on the market. There is a general need for energy conservation, resource conservation and the reduction of carbon dioxide emissions. Thermal insulation is among the remedial measures. Fundamental air pollution abatement measures will have to be avoiding smog warnings which are known to considerably interfere with both economic and private activities.
The contribution under consideration spans a wide curve from the first deadly accident of motorized aviation in the year 1908 up to newer tendencies of the so-called team resources management on observation points and control stations in order to pursue fundamental questions in man-machine systems. A continuous differentiation in the consideration of the factor human beings in complex technical systems is described. This is illustrated by the example of concepts for leadership, communication and decision making on observation points and control stations.
The near-term availability of domestic and selected foreign uranium resources for use by United States electric utilities is considered in light of projected geopolitical and socioeconomic considerations. No attempt is made to analyze the impact on domestic uranium supply of inflation or cost-price considerations, the introduction of the breeder reactor, limitations in enrichment capacity, or the presently expanding uranium inventory. All data are current as of mid-1980. The period with which this research is concerned is 1980-1995. It is concluded that the United States must promote responsible, environmentally acceptable uranium resource exploration and development, if this nation is to remain self sufficient in this necessary energy commodity.
The establishment of workable collaborative relations with indigenous elites formed a vital part of the maintenance of the British Empire. This was especially so in the Malay States, where the Malay rulers enjoyed considerable local prestige as religious leaders and as the organising principle of Malay society itself. As the case of Sultan Ibrahim of Johore demonstrates, nevertheless, indigenous collaborators were no mere puppets and enjoyed considerable freedom of action to frustrate and impede the policies of their imperial overlords. Sultan Ibrahim presents a particularly interesting case study as his 64-year reign more or less spanned the entire period of formal British rule in Malaya.
I formulate a model in which money coexists with equity shares on a risky aggregate endowment. Agents can use equity as a means of payment, so shocks to equity prices translate into aggregate liquidity shocks that disrupt the mechanism of exchange. I characterize a family of optimal monetary policies and find that the resulting equity prices are independent of monetary considerations. I also study a perturbation of the family of optimal policies that targets a positive constant nominal interest rate and find that in this case the real equity return includes a liquidity return that depends on monetary considerations.
A couple of domestic institutions have been investigating the application of vitrification technology to treat low- and intermediate-level radioactive wastes in Korea. In the case that such investigations prove to be successful, it is expected that commercial vitrification plants will be constructed. The safety insuring on vitrification plants could not be compatible with criterion on radioactive waste management because the facilities are at high temperature and contain a variety of accommodations for the exhaust gases and residual products. Therefore, it is necessary to suggest a new strategy or modifications of criterion of radioactive waste management on considerations related with the vitrification technology. In order to ensure the safety of vitrification plants, a technical guideline or standard for design and operation of vitrification plants must be established too. A study on the safety assessment of vitrification plants in ...
Geothermal energy pile foundations are an alternative energy source for heating and cooling needs. Utilising this source of energy has great potential due to the environmental, economic and social benefits. This paper looks at an extensive amount of literature on the technology behind the system including the overall process, primary considerations for each of the main components including latest developments as well as design implications such as the integration of ground energy systems into structural piles of buildings. Environmental considerations including performance-dependent parameters of the subsurface are described. Main parameters include thermal conductivity, thermal diffusivity, specific heat capacity and moisture content. Temperature and groundwater effects are also discussed and design considerations are provided. Mathematical models are available to aid in the design of these systems but there are various ...
Prepared to make housing project managers, maintenance engineering staff, and designers and architects of HUD - assisted and HUD - insured housing projects and mobile home parks aware of their responsibilities under the Natural Gas Pipeline Safety Act, this handbook provides technical guidance for the reduction of gas leaks and the handling of gas leak incidents in residential areas. The hazards of natural gas, concern over gas safety in residential areas, applicable codes and standards, and sources of information and help are reviewed, along with maintenance and engineering considerations relating to gas pipe failures, the detection of gas leaks, appliance servicing, and pipe installation, repair, and replacement. Housing management considerations are also examined, with attention to recordkeeping and reporting, emergency contingency planning, tenant education, staff qualifications and training, and the development and use of a maintenance and ...
Automated, variable volume unloaders provide the ability to smoothly load/unload reciprocating compressors to maintain ideal operations in ever-changing environments. Potential advantages provided by this load control system include: maximizing unit capacity, optimizing power economy, maintaining low exhaust emissions, and maintaining process suction and discharge pressures. Obstacles foreseen include: reliability, stability, serviceability and automation integration. Results desired include: increased productivity for the compressor and its operators, increased up time, and more stable process control. This presentation covers: system design features with descriptions of how different types of the devices were developed, initial test data, and how they can be effectively operated; three actual-case studies detailing the reasons why automated, hydraulically controlled, variable volume, head-end unloaders were chosen over other types of unloading devices; sophisticated software used in ...
The objective of this task was to obtain powder property data on candidate glass former materials, sufficient to guide conceptual design and estimate the cost of glass former handling facilities as requested under Part B1 of BNFL Technical and Development Support. Twenty-nine glass forming materials were selected and obtained from vendors for the characterization of their physical properties, durability in caustic solution, and powder flow characteristics. A glass former was selected based on the characterization for each of the ten oxide classes required for Envelope A, B, and C mixtures. Three blends (A, B, and C) were prepared based on formulations provided by Vitreous State Laboratory and evaluated with the same methods employed for the glass formers. The properties obtained are presented in a series of attached Tables. It was determined that five of the ten glass formers, (kyanite, iron oxide, titania, zircon, and zinc oxide) have the potential to cause some level of solids f low ...
Many pump reliability problems in the Nuclear Power Plants (NPPs) are being attributed to the operation of the pump at flow rates well below its best efficiency point(BEP). Generally, the manufacturer and the user try to avert such problems by specifying a minimum flow, below which the pump should not be operated. Pump minimum flow usually involves two considerations. The first consideration is normally termed the 'thermal minimum flow', which is that flow required to prevent the fluid inside the pump from reaching saturation conditions. The other consideration is often referred to as 'mechanical minimum flow', which is that flow required to prevent mechanical damage. However, the criteria for specifying such a minimum flow are not clearly understood by all parties concerned. Also various factor and information for computing minimum flow are not easily available as considering for the pump manufacturer' proprietary. The ...
Results of X-ray investigations of solid normal hydrogen are presented. Temperature dependences of the lattice parameteps, molar volumes, linear and volume expansion coefficients in the 2K-Tsub(melt) temperature range are obtaiped. An essential n-H/sub 2/ expansion anisotropy in the premelting temperature region is pointed out. It is shown that the hexagonal lattice parameter ratios over the whole investigated temperature range is considerably higher than for solid parahydrogen. A considerable difference in thermal expansion of normal hydrogen and parahydrogen in the low temperature region is revealed. It is caused by contribuation of a rotational subsystem, increasing with the temperature decrease to crystal expansion. A detailed analysis of solid n-H/sub 2/ thermodynamic properties is conducted. The data testifying to the presence of isomorphous phase transformation in the solid n-H/sub 2/ in the premelting temperature region are discussed.
The report presents the results of a Gas Research Institute (GRI) program to evaluate the technical and economic aspects of design options proposed by the U.S. Department of Energy (DOE) for reducing the energy consumption of residential ranges and ovens as mandated by the National Appliance Energy Conservation Act (NAECA) of 1987. The study shows that none of the proposed DOE design options are justified except electric ignition for stand-alone cooktops, based on life-cycle costs, loss of consumer utility, safety, technical considerations, or food quality considerations. An individual range uses so little gas during the year (approximately $14/year for a self-cleaning range) that it is difficult to justify any design modification, since the cost of even a simple modification could not be recovered on the basis of gas saved.
This paper is focused on TLP and Spar technology as applied to floating production applications. In particular, safety considerations as related to classification and certification requirements are addressed. This covers hull structures, marine systems, production facilities and the relevant mooring systems for each platform type from design approval on through construction, installation and ultimately the ongoing maintenance of the platform to acceptable standards throughout its operating life. The experience of the American Bureau of Shipping with these platforms will be utilized in supporting the practical application of classification and regulatory standards to ensure safe operations and concluding that use of such standards in conjunction with an experienced classification society provides a substantial benefit to companies utilizing these technologies. (author)
Even though the currently intensive research efforts on high- temperature superconducting materials have not yet converged on a well specified practical material, the indications are that such a material may be quite brittle, anisotropic, and may contain many flaws such as microcracks and voids at grain boundaries. Consequently, practical applications of high temperature superconducting materials will require a very careful strength analysis based on fracture mechanics considerations. Because of the high sensitivity of the strength of such materials to the presence of defects, methods of quantitative non-destructive evaluation may be expected to play an important role in strength determinations. This proposal is concerned with the use of ultrasonic methods to detect and characterize isolated cracks, clusters of microcracks and microcracks distributed throughout the material. Particular attention has been, and will continue to be devoted to relating ultrasonic ...
A programme to optimize the short-term operation planning of hydrothermal system scheduling is presented. Based on heuristics, an operational planning of pumped storage plants and a method for fast evaluations of spot market deals under consideration of load forecast errors was developed. (orig.) [German] Vorgestellt wird ein Programm, das - basierend auf Heuristiken - den kurzfristigen Einsatz eines hydrothermischen Kraftwerksparks optimiert. Im Programm wurde dazu ein Verfahren zur Pumpseichereinsatzplanung und zur sekundenschnellen Bewertung von Spot-Markt-Geschaeften unter Beruecksichtigung von Lastprognosefehlern entwickelt. (orig.)
This paper summarizes the results of a long-term research project by SKBV which aimed to find ways of increasing spiral chute capacity while minimizing particle degradation, and also to extend the life of chute linings. Spiral chutes have been redesigned in such a way that chute speeds are considerably slower. The most wear-resistant and economic material for the inlet area was found to be slabs of tempered alloy cast steel, and for normal chute sections, cast basalt plates. Vertical rom bunkers can now be lined with thin cladding sections of GRC. Staple pit spiral chutes have been considerably improved in respect to wear and abrasion by the use of toughened steel as the chute lining material. Several of the innovations developed during the course of the research project are in use in West German mines and some have also been introduced abroad. (In German)
The recognition that natural convection offers the prospect of an important inherent safety feature for liquid metal cooled reactor systems has provided the impetus for a world-wide research effort over the past decade. Whilst this research has been based on experiment, both plant experiments and out-of-pile experiments, the enormous advances in the development of computing power in recent years have enabled complementary programmes of mathematical modelling through numerical simulation of the transport equations in three spatial dimensions. These not only offer considerable promise for the designer in projecting the behaviour from experiments and prototype plant to full scale plant, they have also proved to be of considerable value in helping us to interpret and understand the results of the experiments themselves. This paper attempts to review the progress made with the emphasis on decay heat removal by natural convection in the pool-type ...
The energy available from tidal currents is substantial and considerable work has been conducted into determining the size of the resource and what the large-scale consequences of extraction might be. This paper describes the work conducted to establish a laboratory-scale model, by using the commercial computational fluid dynamics (CFD) code FLUENT trademark, in order to predict local-flow consequences resulting from the extraction of energy in two and three dimensions from within the water column in a tidal flow. As might be expected, a wake is formed but there is considerable localized flow acceleration around and, most especially, under an extraction zone. The wake behind the device is shown to be associated with a drop in the free surface which, in turn, is associated with the decline in the wake itself. (author)
To eliminate their classical brittleness and flexibility problems zein films were plasticized by incorporation of different phenolic acids (gallic acid (GA), p-hydroxy benzoic acid (HBA) or ferulic acids (FA)) or flavonoids (catechin (CAT), flavone (FLA) or quercetin (QU)). The use of GA, CAT, FA and HBA at 3 mg/cm2 eliminated the brittleness of films and gave highly flexible films showing elongations between 135% and 189%, while FLA and QU caused no considerable effect on film elongation. The films containing FA and HBA showed extreme swelling and lost their structural integrity when hydrated in distilled water. In contrast, CAT and GA containing films maintained their integrity following hydration. Most of the GA (up to 93%) and a considerable portion of CAT (up to 60%) in the films exis...
Many existing methods of identifying the optimum sites for installing power system stabilizers (PSSs) in multi-machine systems are restricted to the sequential PSS application, which considers the enhancement of damping of just one critical electromechanical mode at a time; the eigenstructure analysis of the open-loop system, which does not take the control matrix (i.e., the B matrix in the linearized model x = Ax + Bu for power systems) into consideration. This paper presents a method of identifying the optimum sites for installing power system stabilizers. The advantages of this method are: it can identify the optimum sites for installing PSSs so that several electrochemical modes are damped out simultaneously; it takes both the eigenstructure of the open-loop system and the control matrix into consideration.
Metal machining facilities pose interesting design problems. This article provides an overview of key environmental control considerations and ways to deal with them. Machine shops offer a variety of environmental control challenges to mechanical engineers. Among the design problems that must be considered include: whether to provide space heating only or year-round air conditioning; temperature and relative humidity requirements; air cleanliness; exhaust air requirements; the type of HVAC system to be used; industrial waste and plumbing considerations; compressed air needs; and noise control. In addition, the designer must comply with worker health and safety and environmental protection regulations set forth by the National Institute of Safety and Health (NIOSH), OSHA, and EPA, as well as with any applicable state and local requirements.
Of the many energy-conservation options available to the design engineer, a system-management approach is recommended as one that will effect maximum benefits to the owner. Systems management includes energy-conscious consideration of design criteria, design details, installation, testing and balancing, and operation. It requires the informed participation of the design engineer, contractor, testing and balancing (TAB) engineer, and owner/operator. Within limits, almost every component of HVAC systems offers an opportunity to conserve energy. Many of these impact energy determinants such as system static pressure, system total air flow, or the quantity of outside air. A few design considerations for energy conservation in a simple system and the impact that the TAB work has on these are illustrated. Particular attention is devoted to the energy impact of systems management, makeup air, and system static pressure.
There are two fundamental reasons or motivations for energy conservation: (1) economics; and (2) consideration of energy - its sources and availability. Economics speaks for itself and needs little explanation: a project is undertaken, the cost is recovered in a given period of time (we hope) and our company realizes cost savings thereafter. We study and propose a project; we estimate the payback. If approved, we implement the project. Then, we eagerly watch for its effectiveness - for the proposed payback. The second consideration in regard to energy conservation might - in the foreseeable future - become by far the most important - that of availability. Very knowledgeable persons have stated that this - in reality - is the most serious problem facing our nation today. Readily available, reasonably priced energy has given to the US the high form of living experienced today. An interruption in this flow could catapult our nation in an awesome ...
The cost incurred every year in West Germany due to air pollution is investigated. Damage to buildings, materials, and vegetation are evaluated as well as the cost of additional cleaning work and changes of location with the objective of getting a picture of the economic value of air pollution abatement. The findings are based on data of immission damage in high-exposure areas. Damage is assessed in consideration of the frequency of repair measures in industrial and country atmosphere. Further research will be necessary in view of the many problems concerning methods and availability of basic statistical data. The sequential cost estimated for a few selected cases of damage show that economic losses due to air pollution amount to several thousand million DM. Air pollution abatement measures thus do not only improve our quality of life but also help to save considerable cost to our national economy.
The presence of an extraneous light gas must be taken into account in consideration of centrifugal separation of uranium isotopes, when there is inevitable leakage of such a gas through the gas sealant and/or leaking in from the atmosphere. Consideration is first given to the influence of the presence of the light gas on the maximum separative power. Then the basic equation for isotope separation containing a light gas is derived from Hirschfelder's diffusion equations. This equation is solved and the separative performance is expressed in terms of the shape factor and reflux parameter. The formulas for expressing the flow configurations of the gases are obtained for a simple model in which inflow and outflow prevail throughout the centrifuge. The corresponding equation for a model in which the gases flow in two concentric thin streams is also derived. It is concluded that the influence provided by the presence of a light gas is quite ...
The assessment and control of fetal exposure to radiation in the workplace is an issue that is complicated by both biological and political/social ramifications. As a result of the dramatic increase in the number of women employed as radiation workers during the past 10 years, many facilities using radioactive materials have instituted fetal protection programs with special requirements for female radiation workers. It is necessary, however, to ensure that any fetal protection program be developed in such a way as to be nondiscriminatory. A study has been initiated whose purpose is to balance the political/social and the biological ramifications associated with occupational protection of the developing embryo/fetus. Several considerations are involved in properly balancing these factors. These considerations include appropriate methods of declaring the pregnancy, training workers, controlling the dose to the embryo/fetus, measuring and ...
Special education researchers have made noteworthy progress toward conceptualizing literacy research questions, designing quality studies, and disseminating the results of their research. These advancements have been made through the establishment and refinement of quality research indicators. Unfortunately, this progress has mostly eluded the arena of juvenile justice special education research. The purpose of this article is to review juvenile justice literacy studies and provide juvenile justice personnel and researchers with methodological and practical considerations for improving the quality of juvenile justice literacy research. The focus is on advancing group designs. Practical concerns are based on the first-year experiences of researchers who implemented an Institute of Education Sciences Goal 3 study with the aim of determining the efficacy of literacy instructional programs in a juvenile justice setting.
This paper discusses a new control strategy for photovoltaic power generation systems with consideration of dynamic characteristics of the photovoltaic cells. The controller estimates internal currents of an equivalent circuit for the cells. This estimated, or the virtual current and the actual voltage of the cells are fed to a conventional Maximum-Power-Point-Tracking (MPPT) controller. Consequently, this MPPT controller still tracks the optimum point even though it is so designed that the seeking speed of the operating point is extremely high. This system may suit for applications, which are installed in rapidly changeable insolation and temperature-conditions e.g. automobiles, trains, and airplanes. The proposed method is verified by experiment with a combination of this estimating function and the modified Boehringer's MPPT algorithm.
The investigation of important wear processes in the railway technique, especially the differentiation of the parameters influencing the wear process, requires extensive test programmes and thus high resolving methods to determine the wear. Radiometric methods enable considerably greater measuring accuracy with the help of the activation of materials than an observation of measurement or measuring changes. (orig./LH).
The report shows that in Europe mountain regions, coastal zones, wetlands and the Mediterranean region are particularly vulnerable to climate change. Although there could be some positive effects, many impacts are likely to be adverse. Existing adaptive measures are concentrated in flood defence, so there is considerable scope for adaptation planning and implementation in other areas, such as public health, water resources and management of ecosystems. (au)
Thermodynamic consideration and process calculations at equilibrium conditions showed that processes for separating gas mixtures by partial condensation at low temperatures using turboexpanders have got less energy losses than processes with quasi isobar partial condensation. Compared to the low-pressure parts of condensing steam turbines in turboexpanders less erosion problems are to expected for such separating processes. Separation of liquid in the machine, however, is more difficult withouf additional measures. (orig.).
Aircraft constitute a unique environment which places stringent requirements on the instruments used to measure the concentrations of atmospheric trace gases and aerosols. Some of these requirements such as minimization of size, weight, and power consumption are general; others are specific to individual techniques. This review presents the basic principles and considerations governing the deployment of trace gas and aerosol instrumentation on an aircraft. An overview of common instruments illustrates these points and provides guidelines for designing and using instruments on aircraft-based measurement programs.
Consideration is given to results of investigation into thorium complexing with morin (H_2Mor) in extraction systems containing different carboxylic acids as well as different salt background. The obtained data enabled to suggest the method of photometric determination of thorium in the form of Th(HMor)_2Benz_2 different-ligand complex (where Benz-anion of benzilic acid) with 0.25 #mu#g/ml detection limit.
The conception of a solar receiver intended to equip a tower power-station has to combine multiple requirements: very highly concentrated solar flux, unsteady in time and space; necessity to obtain a high efficiency; respect of the physical limits of the materials and of the fluid. The description of Themis solar receiver and of its operation is preceded by considerations which have led to the choice of the cavity, of the fluid and of its circulation.
Brain scintiscanning which was first carried out exclusively 'statical' and only with test substances of limited quality has been replaced nowadays by 'dynamical' camera-sequency-scintiscanning with technetium. This brought considerable progress not only for identifying but also for the differential diagnosis of cerebro-organic processes. Development, methods, and integration of brain scintiscanning in a diagnostical conception are described briefly. (orig.).
A new formulation of the theory of tachyons is developed using the same two postulates as in special relativity. Use is made of a 'switching principle' to show how tachyons automatically obey the laws of conservation of energy, momentum and electric charge. Tachyonic mechanics is further developed by a consideration of tachyonic rods and clocks. There follows a discussion of the conservation of electric charge and the apparent visual appearance of a tachyonic cube. 19 refs., 9 figs.
On the 3. and 4. November 1982 the sixth conference of the Corporation for Reactor Safety (GRS) was held in Cologne's Guerzenich. The theme of this year's meeting was the 'Status of Risk Investigations at Nuclear Power Plants'. A principal topic was a report on findings made by the GRS during the 'Risk Oriented Analysis SNR-300'. The second topic comprised the newest developments within Phase B of the Risk Study of Water Pressure Reactors, the discussion of the dose/effect relationship and considerations on threshold risk values. (orig.).
Design considerations of a combined photovoltaic-thermal (PV-T) system for a particular site and application must include thermal and electrical tradeoffs. A simplified technique for determining preliminary design and economic analyses would minimize costly computer simulation and indicate feasibility. To that end, nomographs that size an array to meet a specific annual load and determine the subsequent cost savings have been developed, and are presented in this paper.
The sunlight-induced photocatalytic oxidation of aqueous benzene on TiO(2)-supported gold nanoparticles was considerably improved when the reaction was conducted under a CO(2) atmosphere. 13% yield and 89% selectivity of phenol was obtained on P25-supported gold nanoparticles under 230 kPa of CO(2). PMID:21952312
The Feynman-#alpha# method was applied to measurement of reactivity and the ability of this method for a real-time reactivity monitoring system was assessed. In the experiment, all measured data by BF_3 detectors were stored in a multi-channel scaler controlled by a personal computer, and they were analyzed to obtain prompt neutron decay constant (#alpha#) and reactivity with consideration of dead time of detector. It was found that #alpha# could be obtained almost in a real-time even for both positive and negative reactivities by the present experimental technique. (author).
The influence of heat treatment on the structure, mechanical properties and fracture peculiarities of high-strength (#alpha#+#beta#)-titanium alloy VT22 has been studied. It is ascertained that thermal cycling and subsequent high-temperature aging permit to reduce considerably crack growth rate. Thermal cycling is realized in the following mode: heating in #beta#-region, cooling and allowance in (#alpha#+#beta#)-region, heating in #beta#-region.
Design considerations are given for the secondary side region of a vertical U-tube nuclear stream generator with an integral preheater. The thermal shield design, the novel recirculating water flow distribution scheme, the high porosity tube supports used in the parallel flow regions, and the U-bend supports are discussed for the Wolsung Plant steam generators. Experimental and analytical development programs undertaken to verify the design features are outlined.
This paper shows some considerations about the cost of wood, steel and cement support pillars in rural power distribution systems. The life span, mechanical properties, cost estimation and general durability of each type of pillar was evaluated, aiming a better selection of the desired one. 6 figs., 8 tabs., 4 refs.
In this work, the thermal performance of a conventional collector is improved by inserting porous substrates at the inner walls of the collector tubes. The porous substrates improve the convective heat transfer coefficient between the tube wall and the fluid. This improvement is investigated numerically and its effects on the efficiency and the useful gain of the collector are evaluated. It is found that inserting the porous substrate may raise the collector efficiency considerably, especially at high values of the overall heat loss coefficient.
This extended article describes Sasol, the synthetic fuel producing plant in South Africa. It produces other fuels in addition to synfuel, from local coal. A very thorough review covering all aspects of the plant is given. These include: economic; chemical and environmental. The chemistry of the processes involved, the Fischer-Tropsch synthesis and the Lurgi process are described in some detail. Consideration is also given to the establishment of new plants, research and development projects, marketing and available coal resources.
Some aspects of molecular mechanisms common to radiation and chemical carcinogenesis are discussed, particularly the DNA damage done by these agents. Emphasis is placed on epidemiological considerations and on dose-response models used in risk assessment to extrapolate from experimental data obtained at high doses to the effects from long-term, low-level exposures. 3 references, 6 figures. (ACR)
This short article describes the strategies taken into consideration by the Swiss Federal Office of Energy for the promotion of renewable forms of energy in Switzerland. Two basic models are considered and the parts to be played by the Swiss Confederation, the Swiss Cantons, Energy Agencies and professional organisations are discussed. The importance of the activities of partner organisations and actor-networks in various areas such as solar, small hydro, geothermal and wind energy are discussed, as are models for financing the necessary promotion and marketing efforts
The alumina industry is facing worldwide a growing disposal problem. Red mud creates increasingly technical, economic and environmental problems. Available solutions are reviewed and an old idea using a new approach with pressurized disc or drum filters for red mud is herewith presented and submitted for consideration as a potential and prospective solution to the problem.
An introduction is presented on the radiation hazards connected with biomedical radiography and nuclear medicine. The frequency of radiodiagnostic efforts was rather high in the Netherlands. This was reduced considerably by abolishing the thorax screening of the population. About diagnostic nuclear medicine less can be said because far fewer numerical data are available. An exposition of genetically and somatically significant doses and how to compute them is given. The drawing up of a profit versus risk evaluation for medical applications of ionizing radiations is recommended. (Auth.).
A set of eight questions was put to advanced nuclear medicine physicians-in-training participating in a continuing assessment exercise in practical therapeutic nuclear oncology. Using the particular example of {sup 131}I-MIBG treatment of neuroblastoma in children, the questions were directed to the rationale of therapy and the contribution of other forms of treatment to toxic effects. The best answer to the questions are reproduced together with an introduction by the examiner, Dr. H. Turner. tabs.
Pyrheliometric methods are described (particularly methods for measuring the solar constant), and theoretical and experimental studies in this field are surveyed and systematized. Particular attention is given to the analysis of instruments intended for pyrheliometers used as standards, reference instruments, and solar-constant meters is examined, and consideration is given to methods for determining the thermal-radiation properties of absorbing coatings and methods for calculating the absorption coefficients of cavity receivers.
This article discusses the latest developments made in the field of technology used for coal liquefaction. Some new areas of development in research and development work are described. Particular consideration is given to low-severity processing. This has two advantages, mostly low-molecular-weight fragments are produced and the extracts are low in heteroatoms. A detailed description of low-severity processing is given. The refining of the liquids produced from coal is also covered.
Military working dogs are rapidly becoming integral to military operations. While they bring many valuable capabilities to the battlefield, it is important that Special Operations leaders consider canine team capabilities and requirements when planning missions. Careful logistical and operational planning can optimize the health, performance, and readiness of the working dog while protecting the safety and well-being of the team members working with them. We also offer recommendations for medical treatment of dog bites. PMID:19813342
Several of the issues of the workshop are addressed from the perspective of a potential Space Station developer and energy wheel user. Systems considerations are emphasized rather than component technology. The potential of energy storage wheel (ESW) concept is discussed. The current status of the technology base is described. Justification for advanced technology development is also discussed. The study concludes that energy storage in wheels is an attractive concept for immediate technology development and future Space Station application.
The use of nuclear reactors to provide electrical energy has shown considerable growth since the first nuclear plant started commercial operation in the mid 1950s. Although the main purpose of this paper is to review the fuel cycle capabilities in the United States, the introduction is a brief review of the types of nuclear reactors in use and the world-wide nuclear capacity.
In this paper the possibility of using the test facility PACTEL concerning the investigations of thermal hydraulic special features of the primary coolant circuit acting under natural circulation is under consideration. It is suggested to study a stratification phenomenon of a coolant in upper plenum of a reactor and also a horizontal steam generator (HSG) hot collector temperature regime. For such investigations the facility must be modified. It is shown that this work is not large and expensive, as the facility is a lightly suitable unit for different researches. (orig.)
In this paper the possibility of using the test facility PACTEL concerning the investigations of thermal hydraulic special features of the primary coolant circuit acting under natural circulation is under consideration. It is suggested to study a stratification phenomenon of a coolant in upper plenum of a reactor and also a horizontal steam generator (HSG) hot collector temperature regime. For such investigations the facility must be modified. It is shown that this work is not large and expensive, as the facility is a lightly suitable unit for different researches. (orig.)
Mutual influence of phosphorus and carbon on the tendency to integranular corrosion (IGC) of tempered austenitic stainless steels in boiling solutions of 65% HNO_3 and 27% of HNO_3+40 g/l Cr"6"+ was investigated. It is ascertained that under the action of carbon additions susceptibility of phosphorus-containing steels to IGC increases considerably in pure nitric acid and decreases in nitric acid containing the oxidant. Possible reasons for the effects observed are discussed.
The Monte Carlo simulation method is applied to calculate the nucleon transfer part of the imaginary optical-model potential in colliding heavy ions. In the process of transfer of nucleons from one nucleus to the other, forward and backward neutrons and protons are treated separately by taking into consideration the effect of the Coulomb forces and the potential energy surfaces (driving forces). The Pauli exclusion principle is also incorporated properly in the calculation.
The effect of nuclear scattering on the suprathermal fusion probability of recoiling d-t nuclei under the impact of fusion products, a 14.1-MeV neutron and a 3.5 MeV alpha particle, in thick pellets is investigated with the help of the Boltzmann-Fokker-Planck equation. Although the suprathermal fusion from alpha-particle recoils is quite small, the one originating from neutron recoils is considerable.
As part of a handbook on the efficient use of energy a chapter is included which is intended to give an appreciation of the principles and problems involved in the generation of nuclear power. The subject is discussed under the following headings: introductory nuclear physics; basic reactor physics; thermal reactors; fast reactors; fuel reserves and utilization; environmental considerations; nuclear fusion. (U.K.).
The uncertainties of growth in Croatian future energy, particularly electricity demand, together with growing environmental considerations and protection constraints, are such that Croatia needs to have flexibility to respond by having the option of expanding the nuclear sector. The paper deals with nuclear energy as an option for croatian sustainable economic development. The conclusion is that there is a necessity for extended use of nuclear energy in Croatia because most certainly nuclear energy can provide energy necessary to sustain progress. (author).
Nanocrystalline materials can exhibit properties which are considerably different from their coarse-grained counterparts, making them unique for basic or applied research and also very promising for potential applications. The topics which are addressed in the present paper are magnetic properties and magnetic correlations on the nanometer scale, mechanical properties, in particular the influence of grain boundaries on the elastic and plastic behaviour, and vibration models of grain boundary atoms in nanostructured materials. (author)
The suitability of using the microwave oven for the rapid determination of total solids content (TSC) of natural rubber latex has been established over a broad range of dry rubber content (DRC). The total solids content values obtained by the microwave oven method are compared with the values obtained by heating in a conventional convection oven. Heating in a microwave oven is advantageous as the measurement time could be reduced considerably.
In these notes I discuss various aspects of the elusive M-theory, with a special stress on the structure of the supergravity effective descriptions and their relations. These notes are arranged into 7 chapters: (1) Introducing the supergravities, (2) The bound state problem, (3) Unitary and supergravity theories, (4) Superstring theory considerations, (5) Non-perturbative contributions, (6) Unitary techniques in supergravity theories, and (7) Instantons computation and the adS/sCFT correspondence.
The management procedure of a large PRISE (Primary-to-Secondary) leakage accident at Loviisa nuclear power plant taking into account the plant modifications which are expected to be realized during 1995-96 is described. The management procedure has been validated by performing thermal hydraulic analyses with the computer code RELAP5/MOD3 and the results from these analyses are also shortly discussed. (4 refs., 6 figs., 1 tab.).
In accordance with the comprehensive plan in the eleventh five-year period the main content of prospecting and exploration on land in Axerbaidzhan by the Axneft' association will be done in the central and Western regions of the republic, where Paleogene-Mesozoic deposits will be inspected. Discussed in detail are the directions and volumes of prospecting and exploration in individual regions of Azerbaidzhan. They are determined with consideration of the degree of exploration of the earth's interior, the prospects for the deposits comprising them, and the development of the resources of oil.
During the period covered by this report research has been concerned with the study of photo-induced electron transfer reactions from porphyrins to acceptor molecules with time-resolved Electron Paramagnetic Resonance (EPR) methods. Excited-state electron transfer reactions are of importance from a fundamental point of view and in connection with applications in homogeneous and heterogeneous photosensitization, photopolymerization, and solar energy conversions. For this reason, the study of photo-induced electron transfer reactions is of considerable interest.
Magnetic resonance imaging can be used in the trauma setting to detect fractures and associated soft tissue injuries of the musculoskeletal system. Magnetic resonance imaging complements plain radiography and CT for evaluating cancellous bone, cartilage and growth-plate injuries, and intra- and extraarticular supporting soft tissue structures. This review outlines typical applications and imaging consideration for injuries of the pelvis and lower extremity. (orig.) With 12 figs., 78 refs.
This paper identifies some of the issues which arise in the consideration of the derivation of new limits on exposure to internal emitters. Basic and secondary radiation protection limits are discussed. Terms are defined and applied to the limitation of risk from stochastic effects. Non-stochastic data for specific internal emitters (/sup 131/I and the radium isotopes) are presented. Emphasis is placed on the quantitative aspects of the limit setting problem. 65 references, 2 figures, 12 tables.
Revisions at steam turbines should present a problem-free procedure due to the long use of these machines. Changes in the market result in difficulties during the inspection work. The shortage of qualified personnel and manufacturing capacities are the cause for these difficulties. Important procedures of revisions are described in detail in the VGB regulations. Direct contacts between the customers and the suppliers facilitate the expirations substantially. In the case of good planning and under consideration of the well-known regulations, a revision can be accomplished to the satisfaction of customers and suppliers.
Within the EU-Project VOTALP (Vertical Ozone Transports in the Alps), we have shown that deep alpine valleys like the Mesolcina Valley very efficiently transport air out of the polluted valley up to altitudes between 2000 and near 4000 m asl (above sea level). Pollutants emitted in these valleys are very efficiently transported up to high altitudes. (author) 2 figs., 1 tab., 2 refs.
The requirements of high-pressure compressors increase. The customers wish still larger quantities of delivery with smaller employment of achievement, minimal oil consumption, service amenability, long intervals of maintenance and so forth. For this, the author of the contribution under consideration presents two series of modular developed high-pressure compressors in compact design for industrial air and technical gases which exactly fulfil these requirements.
During four years of operation at the Central Receiver Test Facility (CRTF) ceramics have performed well in cyclic solar flux densities of less than 30 W/cm/sup 2/. Above 100 W/cm/sup 2/, serious limitations exist. Important application considerations include: the geometry, cyclic and long time exposures, flux density gradients, thermal shock, weathering, and soiling.
This paper presents general considerations concerning the application of artificial neural networks algorithms, more specifically the back-propagation learning algorithm and feed-forward multi-layer networks, to several problems in power system. The main application in power systems is the load forecasting, and two solution methods are used to solve it. (author). 45 figs., 32 tabs., 144 refs.
This paper presents a theoretical study of heat transfer from magneto-rheological fluid (MRF) dampers. A lumped system model is developed which is capable of predicting the temperature rise for any size MRF damper. As a case study example, finned and unfinned dampers are compared for automotive-size MRF dampers. The results demonstrate that heat transfer from these devices can be enhanced considerably with the use of fins.
An experimental study was undertaken to determine for the turbulent regime the heat transfer and fluid flow characteristics of a heat exchange array of unperforated, and perforated brass plates with 33% of the plate area open. In both cases, the plates were aligned parallel to the flow direction. For the flow conditions examined, the results showed enhancement of heat transfer and friction factor for the perforated array.
This manual is a guide to the services provided by the Hanford Internal Dosimetry Program (IDP), which is operated by the Pacific Northwest National Laboratory.( ) for the U.S. Department of Energy Richland Operations Office, Office of River Protection and their Hanford Site contractors. The manual describes the roles of and relationships between the IDP and the radiation protection programs of the Hanford Site contractors. Recommendations and guidance are also provided for consideration in implementing bioassay monitoring and internal dosimetry elements of radiation protection programs.
Ground water ranging in temperature from only 38/sup 0/ to 140/sup 0/F can supply a considerable amount of heat energy when couple with a geothermal or ground-water heat pump. The heat pump's method of operation is examined as well as its performance characteristics. (MHR)
This article examines the question of finding the best quadratic function to approximate a given function on an interval. The prototypical function considered is f(x) = ex. Two approaches are considered, one based on Taylor polynomial approximations at various points in the interval under consideration, the other based on the fact that three non-collinear points determine a unique quadratic function. Three different techniques for measuring the error in the approximations are considered.
This document presents the details of the implementation of the Site Treatment Plan developed by Ames Laboratory in compliance with the Federal Facilities Compliance Act. Topics discussed in this document include: implementation of the plan; milestones; annual updates to the plan; inclusion of new waste streams; modifications of the plan; funding considerations; low-level mixed waste treatment plan and schedules; and TRU mixed waste streams.
...-such as the EU -suggests a considerably larger effect of such agreements on membersrsquo; trade than typical ex ante CGE models and traditional cross-section empirical analyses (using traditional ldquo;gravity equationsrdquo;). These larger estimated effects are more consistent with the active role of national governments ...
In November 1998, President Clinton charged the National Bioethics Advisory Commission with the task of conducting a thorough review of the issues associated with human stem cell research, balancing all ethical and medical considerations. The President's ...
Interactions between spacecraft systems and the space charged particle environment are reviewed and recommendations are presented for both near-term and far-term research considerations. Transient environment models, large space structures, solar and nuclear power systems/environment interactions, single event upsets, material degradation, and planetary missions are addressed.
Since many years, people take care of hazardous consequences of a non controlled economic growth and the sustainable development concept gains on one. This situation leads to consequences in the building industry and in the energy policy: buildings insulation in consideration, demand of consultants. In this framework, the partnership between Gaz De France and CICF has to be built. (A.L.B.)
Within the Westeuropean network of the electric current supply a continuing compensation is necessary with respect to the permanent alterations of capacity and frequency. Pumped-storage plants are of considerable significance to meet these requests. The Schluchseewerk AG, Freiburg/Breisgau, has among others five pumped-storage plants in the southern part of the Black Forest. The conception and the operation of them are described. (orig.).
Image representations have gained wide acceptance in displaying data collected during optical, ultrasonic, radiographic, and thermographic inspections. Applying imaging techniques to eddy current testing is explored in this article. The authors show that flaw interpretation and characterization are made considerably simpler when images are used to visualize the impedance changes in eddy current probes.
The two favourable dry storage concepts being under consideration in the Federal Republic of Germany are presented and the physical behaviour or natural convection cooling with air is explained. With the three examples cask store, vault storage horizontally and vertically arranged the main thermodynamical design parameters and their influence on the efficiency of the cooling system and on the temperature distribution inside the store and of the stored material are discussed. Moreover, the importance of the fulfilment and the harmony of all safety criteria and the difficulties while to do so are carried out especially with the vault store.
During this report period our research efforts have concentrated on studies of the dissociation reactions of model peptides and other biologically important molecules. In addition, a considerable amount of research effort has been directed toward improving the apparatus used for laser-ion beam photodissociation. The instrumental improvements include some changes on the original apparatus, but most of this effort involved designing a second generation laser-ion beam photodissociation instrument.
The author attempts to calculate the absolute characteristics of explosives unrelated to the effects of environment, particularly for that part of the work of the explosion done by the expansion of the detonation products. Setting forth his equations and noting their agreement with experimental data, he concludes that for a complete characterization of the relative effectiveness of explosives it is necessary to know the pressure, mass velocity, and polytropic index of the detonation products, but that developed considerations of the relation between performance and detonation characteristics permit a more exact evaluation of various explosives and unification of the nomenclature of explosives and methods of testing them.
Cesium and selenium intake of cultivated mushrooms (Agaricus bisporus), with these elements previously added to culture medium, has been examined from the viewpoint of health- and environmental protection. The process of measuring has been carried out by the radionuclide X-ray fluorescence technique. Treatments of the elementary substance with Se salt appears to influence the Se content of the mushrooms to a significant extent. Cs intake is of considerable importance, as this element is accumulated by mushrooms. (author)
A prototype of a muffin-tin accelerating structure operating at 32 times the SLAC frequency (2.856 GHz) was built for research in high gradient acceleration. A traveling-wave design with single input and output feeds was chosen for the prototype which was fabricated by wire electrodischarge machining. Features of the mechanical design for the prototype are described. Design improvements are presented including considerations of cooling and vacuum.
The UK Pipelines Safety Regulations require the pipeline operator to ensure that a pipeline, once decommissioned, does not become a source of danger. Elsewhere, Regulatory Authorities require consideration of the possible issues which pipeline decommissioning may raise. This paper considers current practice with respect to pipeline decommissioning and abandonment, and sets out the range of factors which the operator must take into account. (author)
Preparation of the clinician to work in multicultural contexts involves the identification of a range of skills, knowledge and values. The field of narrative medicine as well as an increased understanding of the dynamics of interpreting are areas which can add considerably to clinical effectiveness. The paper outlines some cornerstones of narrative medicine and their potential application to the field of speech-language pathology and audiology. PMID:12037426
Several aspects of heat transfer at the annular two phase flow regime are considered. Nucleate boiling is supposed to be absent. Theoretical solutions for cases of laminar and turbulent flow in the liquid film, respectively, are considered, when steam presence does not effect the heat transfer. Heat transfer in annular flows is also considered, where steam phase consists totally or partially of the so-called incondensable gas. In this case steam phase can be a considerable resistance to heat transfer.
Bony craniofacial deficits resulting from injury, disease, or birth defects remain a considerable clinical challenge. In this study, microsphere-based scaffold fabrication methods were use to...Full Text Available
This monograph addresses a narrow aspect of cold regions engineering, namely the effects of cold weather on the traditional civil engineering disciplines of hydrology and hydraulics. Hydrologic and hydraulic considerations in the design, construction, and operation of civil works are very important. Many of the problems encountered in the design and construction of buildings, transportation systems, water supply facilities, waste treatment facilities, and hazardous waste disposal facilities, for example are closely tied to the characteristics of the site hydrology.
Consol R D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-fold: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.
Consol R D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-field: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.
This study reviews 16 cases of chondroblastoma of the patella which constitute mearly 6% of a large group of chondroblastomas scattered throughout the skeleton. Both radiologic and histologic appearances of chondroblastomas of the patella are indistinguishable from those of chondroblastomas arising in other sites. A reasonable differential diagnosis, including chondromalacia patella, is discussed together with important therapeutic considerations. (orig.).
Equations are compiled for thermal balance in which for simplification, no consideration is made for heat conductivity along the axis of the cable and dependence of losses, heat capacitance and heat conductivity on temperature. Equations are modeled on a transistor analog calculator 42 TA. The solution to the task on the computer produced values of maximum temperature on the cable and coordinates of the point of maximum overheating. Using the analog model, one can study other parameters of the thermal mode.
The physical principals of the interaction between microwaves and matter are considered along with the physical-chemical mechanisms for the absorption of microwave energy by biological tissue. Consideration is given to results of studies of the effects of microwaves on cells, subcellular structures, and membranes. Medical applications of microwaves are discussed along with the development of health standards for the use of microwaves. 122 references.
Spark ignition internal combustion engines perform satisfactorily when the fueled with biomass producer gas from a fluidized bed gasifier. Although power output is reduced compared to natural gas levels, full power recovery can be achieved with a relatively low level of supercharging. Important considerations are an adequate fuel delivery system and adquate gas cleaning. ref.
An FEL amplifier to generate a laser power of the order of TW at 4 {mu}m wavelength is investigated for a {gamma}-{gamma} collider. A concept of an amplifier chain consisting of a phase-displacement deceleration FELs is proposed to increase the FEL efficiency and to mitigate the requirement for the beam energy spread. The feasibility of the driving linac for the FEL system is also discussed. ((orig.)).
An FEL amplifier to generate a laser power of the order of TW at 4 #mu#m wavelength is investigated for a #gamma#-#gamma# collider. A concept of an amplifier chain consisting of a phase-displacement deceleration FELs is proposed to increase the FEL efficiency and to mitigate the requirement for the beam energy spread. The feasibility of the driving linac for the FEL system is also discussed. ((orig.)).
In this article, equations of motion of a manipulator are derived after consideration of the characteristics of the driving source. By considering a collision between a link and an object, and considering the active motion to absorb the kinetic energy of the object, the trajectories for saving energy are calculated by the iterative dynamic programming (IDP) method. The dynamic characteristics of manipulator control based on the trajectory for saving energy are also analyzed theoretically and investigated experimentally.
Afterheat represents an important consideration in design of conceptual fusion power reactors, particularly during normal or unplanned shutdown. Afterheat calculations have been undertaken for various generic designs, but with special reference to the Culham DEMO reactor. These calculations have included the redistribution of heating by gamma ray transport. Selected temperature response calculations have been undertaken. (author).
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
This book contains nine selections. Some of the titles are: High Heat-Flux, Forced-Convection Heat Transfer for Tubes with Twisted-Tape Inserts; Heat Transfer Augmentation by Interrupted Surfaces - Experimental Consideration; Turbulent Flow Heat Transfer from Externally Roughened Tubes in Axial Flow in Concentric Pipe Heat Exchangers; and Heat Transfer Enhancement of Turbulent Flow in Pipes with an Internal Circular Rib.
BACKGROUND:Despite an increasing body of evidence on the benefit of lowering elevated levels of low-density lipoprotein cholesterol (LDL-C), there is still considerable concern that...Full Text Available
The doping of deuterated polyparaphenylene [C_6D_4]sub(n) with AsF_5 has been investigated by real time neutron diffractometry at 100, 400 and 820 mbar AsF_5 pressure. The reaction appears to be diffusion controlled. Evidence for one doped phase with partial crystalline order was obtained. Structural considerations suggest two polymer chains plus one dopant ''string'' as the repetitive unit. (Auth.).
A dual-rate self-tuning control technique, in which the system identification and control calculation are performed separately, is proposed in this paper. This greatly increases the control rate. A self-tuning power system stabilizer (DSPSS) making use of this technique is developed and implemented using multi-micro-computers. Simulation and experimental results with DSPSS show that the increase in the control rate can considerably improve the system performance.
Significant recent writings have suggested strong parallels and actual links between the historical legal architectures of Canadian Aboriginal policy and South African apartheid. This article's further probing of these claims shows them to be very doubtful. At the same time, some more limited legal parallels between the two systems shows the importance of undertaking further analysis of the transmission and exchange of legal ideas and norms within the Commonwealth order.
An approach for classification of transmission line faults is presented. The approach is based on fuzzy logic and requires the consideration of the samples of three phase currents at one end of transmission line. To illustrate the effectiveness of the proposed approach extensive simulation studies, using EMTP and MATLAB, have been carried out for different types of fault considering wide variations in the operating conditions. (author)
During the last several years, audible noise produced by high voltage transmission lines in corona has emerged as an important design consideration. In this same time frame a number of different methods for calculating audible noise levels have been proposed. The methods currently available, for both ac and dc lines, are described in this paper and are compared through application to practical line geometries for which data from long-term measurements are available.
This program is designed in order to calculate electricity generation cost by different energy sources, and menu type is adopted for user convenience. This program also graphically shows the share of capital investment cost, O and M cost, and fuel cost. Sensitivity analysis about discount rate can also be carried out by this program, taking into consideration the important role of the discount rate in the generation costs calculation. (Author) 7 refs., 1 fig., 3 tabs.
The present guidelines supplement the 'VGB guidelines for the reduction of noise in thermal power plants' with indications for the ordering and quality assurance of the individual noise-producing machines and equipment of power plant operation. These guides are to simplify the commissioning and delivering for the orderer and deliverer. In addition, these guidelines are to lead to a successful cooperation of all parties in the reduction of the sound radiation. A precondition for this is an explanation of the sound technical demands which must be made on the single machines or mechanical equipment in power plant systems. A protection of the neighbourhood as well as operational personnel against noise according to the state of technology is to be achieved by a clear form of ordering and quality assurance. The ordering and assurance procedure for all aggregates in the region of the grounds of a power plant up to the high-voltage side of the machine transformers is included in these ...
Geographic information system (GIS) technology is now being used by wind energy developers who are required to consider and accommodate a wide variety of environmental and social considerations. This poster presentation discussed some of the new features available in current GIS technologies. High resolution imagery from satellites is being used to verify the accuracy of collected spatial data, as well as to investigate potential locations for meteorological towers, turbine sites, and roads. Slopes are easily calculated using GIS software tools, and digital elevation data can be used with high resolution aerial photography to determine routes for new roads and to establish available sites for crane pads. The GIS tools allow developers to consider protected ecological areas, wetlands and forests, and gives them the ability to better report project development considerations at public consultations. Wind resource grid outputs can also be ...
Since the first round of conceptual fusion reactor designs in 1973 - 1974, there has been considerable progress in design improvement. Two recent tokamak designs of the Wisconsin and Culham groups, with increased plasma beta and wall loading (power density), lead to more compact reactors with easier maintenance. The Reference Theta-Pinch Reactor has undergone considerable upgrading in the design of the first wall insulator and blanket. In addition, a conceptual homopolar energy storage and transfer system has been designed. In the case of the mirror reactor, there are design changes toward improved modular construction and ease of handling, as well as improved direct converters. Conceptual designs of toroidal-multiple-mirror, liner-compression, and reverse-field pinch reactors are also discussed. A design is presented of a toroidal multiple-mirror reactor that combines the advantages of steady-state operation and high-aspect ratio. The ...
Several researchers have examined and achieved favourable results in connection with the building industry's use of red mud extracted in large quantities from the processing of bauxite. These days more and more precedence is being given to limiting the radiological dose to the population. In this study carried out in Hungary, the use of red mud, bauxite, and clay additives recommended for the production of special cements, were examined from a radiological aspect. "2"2"6Ra and "2"3"2Th activity concentrations measured in Hungarian bauxite, red mud and clay samples were significantly similar with the levels for such raw materials mentioned in international literature. Taking radiation protection aspects into consideration, none of these products can be directly used for building construction. Taking Hungarian and international values into consideration, a small amount of red mud, not exceeding 15% could be used for brick production, for example ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for component ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for component failures ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for component failures ...
The authors present a state-of-the-art review of natural circulation heat transfer in loop type reactor plants. Most of the examples are taken from Fast Flux Test Facility (FFTF) design experience, drawing on the authors' familiarity and a developing base of available documentation. On-going studies related to the Clinch River Breeder Reactor (CRBR) and some foreign experience are also noted where available in the literature. The emphasis is on the role of natural circulation in decay heat removal; however, free convection during either operation at power or normal shutdown does influence some aspects of the design and these are reviewed. In treating decay heat removal the topics discussed include steady state loop performance and transient dynamics for conditions immediately after scram and for the longer term which involves different considerations. The review summarizes complex dynamics, specific to the FFTF design evaluation, which particularly illustrate large ...
The National Spallation Neutron Source (NSNS), in which neutrons are generated by bombarding a liquid mercury target with 1 GeV protons, will place extraordinary demands on materials performance. The target structural material will operate in an aggressive environment, subject to intense fluxes of high energy protons, neutrons, and other particles, while exposed to liquid mercury and to water. Components that require special consideration include the Hg liquid target container and protective shroud, beam windows, support structures, moderator containers, and beam tubes. In response to these demands a materials R and D program has been developed for the NSNS that includes: selection of materials; calculations of radiation damage; irradiations, post irradiation testing, and characterization; compatibility testing and characterization; design and implementation of a plan for monitoring of materials performance in service; and materials engineering and technical ...
SiC has been considered as a primary candidate material for a first wall component in future fusion reactor because it has been claimed that SiC has excellent high-temperature properties, good chemical stability and low activation. However, the behavior of tritium on SiC has not been discussed yet. In this study, tritium trapping capacity on the surface of SiC was experimentally obtained at the temperature range of 25-800 deg. C in consideration of tritium trapping to the experimental system. The capacity, which was independent of the water vapor pressure in the gas phase and the temperature, was determined as about 10{sup 6} Bq/cm{sup 2}. The isotope exchange reaction rate between tritiated water in a gas phase and hydrogen on the surface was quantified at the temperature of 25, 500 and 700 deg. C in consideration of the behavior of tritium trapping at change of experimental condition by the numerical curve fitting method applying the serial ...
SiC has been considered as a primary candidate material for a first wall component in future fusion reactor because it has been claimed that SiC has excellent high-temperature properties, good chemical stability and low activation. However, the behavior of tritium on SiC has not been discussed yet. In this study, tritium trapping capacity on the surface of SiC was experimentally obtained at the temperature range of 25-800 deg. C in consideration of tritium trapping to the experimental system. The capacity, which was independent of the water vapor pressure in the gas phase and the temperature, was determined as about 10"6 Bq/cm"2. The isotope exchange reaction rate between tritiated water in a gas phase and hydrogen on the surface was quantified at the temperature of 25, 500 and 700 deg. C in consideration of the behavior of tritium trapping at change of experimental condition by the numerical curve fitting method applying the serial reactor ...
The Sp-100 reactor is a lithium-cooled high-temperature fast-spectrum reactor. The fuel is UN. The cladding is fabricated from PWC-11, a Nb alloy, as are all the primary structural components. A reactor lifetime of up to ten years with an operating temperature of 1370 K is required. The accumulated fluence is expected to be 6 x10"2"2 n/cm"2. The damage, which could result in swelling or embrittlement, anneals out as fast as it occurs for the majority of the structure. This has been confirmed by earlier radiation testing. A number of components, however, are exposed to lower temperatures and the reactor design and materials selection for these components must take this into consideration. Radiation effects must also be considered for the UN fuel, bearing materials, etc. To data an instrumented experiment, MOTO 1000A, has been conducted in the FFTF reactor and as uninstrumented experiment SPM-1 in the EBR-II reactor. In this paper the post-irradiation examination and ...
This Public Design Report provides, in a single document, available nonproprietary design -information for the ``Innovative Coke Oven Gas Cleaning System for Retrofit Applications`` Demonstration Project at Bethlehem Steel Corporation`s Sparrows Point, Maryland coke oven by-product facilities. This project demonstrates, for the first time in the United States, the feasibility of integrating four commercially available technologies (processes) for cleaning coke oven gas. The four technologies are: Secondary Gas Cooling, Hydrogen Sulfide and Ammonia Removal, Hydrogen Sulfide and Ammonia Recovery, and Ammonia Destruction and Sulfur Recovery. In addition to the design aspects, the history of the project and the role of the US Department of,Energy are briefly discussed. Actual plant capital and projected operating costs are also presented. An overview of the integration (retrofit) of the processes into the existing plant is presented and is followed by detailed non-proprietary descriptions ...
Recent developments in heat pump technology have made geothermal-based heat exchange systems particularly well-suited for the heating and cooling needs of buildings even in cold climates. The principles of geothermally-coupled heat pump heating and cooling systems were presented. Results of an in-situ study conducted by Hydro-Quebec on the efficiency of the geothermal heat pump system installed at the Saint-Hyacinthe professional school were summarized. This investigation was meant to be a case study of the applicability of these new technologies to the needs of the Quebec market. After the first year of service, the Saint-Hyacinthe system clearly demonstrated its cost effectiveness over conventional systems. It was predicted that geothermal heat pump systems will gain in popularity in Quebec because they can fully meet the heating and cooling needs of public buildings at considerable cost reductions, besides offering considerable environmental ...
A wider use of renewable energy sources is considered to be the solution to fossil fuel depletion and environmental pollution. This paper discusses various design considerations for line focussing technology to achieve high efficiency and the possibility of generating power in the megawatt range based on solar thermal technologies. The impacts on the environment of conventional thermal power plants is outlined and an estimate made of the cost of pollution abatement measures. A cost benefit analysis is made using a typical 200 megawatt solar thermal plant, 500 km from the load centre, compared with a 220 megawatt coal fired and a similar capacity gas fired power plant, as examples. The results indicated that the energy from the solar thermal power plant is almost twice as expensive compared to conventionally generated electricity. If, however, impacts on the environment and notional cost associated with are considered, electricity from coal plants becomes either ...
A wider use of renewable energy sources is considered to be the solution to fossil fuel depletion and environmental pollution. This paper discusses various design considerations for line focussing technology to achieve high efficiency and the possibility of generating power in the megawatt range based on solar thermal technologies. The impacts on the environment of conventional thermal power plants is outlined and an estimate made of the cost of pollution abatement measures. A cost benefit analysis is made using a typical 200 megawatt solar thermal plant, 500 km from the load centre, compared with a 220 megawatt coal fired and a similar capacity gas fired power plant, as examples. The results indicated that the energy from the solar thermal power plant is almost twice as expensive compared to conventionally generated electricity. If, however, impacts on the environment and notional cost associated with are considered, electricity from coal plants becomes either ...
Cementitious materials have physical and chemical properties that are well suited for the requirements of radioactive waste management. Namely, the materials have low permeability and durability that is consistent with the time frame required for short-lived radionuclides to decay. Furthermore, cementitious materials can provide a long-term chemical environment that substantially reduces the mobility of some long-lived radionuclides of concern for decommissioning (e.g., C-14, Ni-63, Ni-59). Because of these properties, cementitious materials are common in low-level radioactive waste disposal facilities throughout the world and are an attractive option for entombment of nuclear facilities. This paper describes design considerations for cementitious barriers in the context of performance over time frames of a few hundreds of years (directed toward short-lived radionuclides) and time frames of thousands of years (directed towards longer-lived radionuclides). The ...
Cementitious materials have physical and chemical properties that are well suited for the requirements of radioactive waste management. Namely, the materials have low permeability and durability that is consistent with the time frame required for short-lived radionuclides to decay. Furthermore, cementitious materials can provide a long-term chemical environment that substantially reduces the mobility of some long-lived radionuclides of concern for decommissioning (e.g., C-14, Ni-63, Ni-59). Because of these properties, cementitious materials are common in low-level radioactive waste disposal facilities throughout the world and are an attractive option for entombment of nuclear facilities. This paper describes design considerations for cementitious barriers in the context of performance over time frames of a few hundreds of years (directed toward short-lived radionuclides) and time frames of thousands of years (directed towards longer-lived radionuclides). The ...
The question concerning the existence of an electronic topological transition (ETT) in Zn metal under quasi-hydrostatic pressure at #approx#6.6 GPa caused a considerable controversy in the literature. We briefly review low-temperature "6"7Zn-Moessbauer data and scalar-relativistic augmented plane wave calculations and give a consistent interpretation in terms of an ETT. To highlight some important aspects of the controversy two theoretical and two experimental publications will be discussed in more detail. At present the existence of an ETT in Zn metal is disputed both from an experimental and from a theoretical point of view. The suggestion of a transition to a commensurate spin-density wave at #approx#6.6 GPa instead of an ETT may reconcile the seemingly contradictory results of "6"7Zn-Moessbauer experiments at 4.2 K and of room temperature inelastic neutron scattering measurements. However, it does not explain the anomalies found in theoretical calculations ...
We discuss the evolution of a disc galaxy due to the formation of a bar and, subsequently, a peanut. After the formation stage there is still considerable evolution, albeit slower. In purely stellar cases the pattern speed of the bar decreases with time, while its amplitude grows. However, if a considerable gaseous component is present in the disc, the pattern speed may increase with time, while the bar strength may decrease. In some cases the gas can be brought sufficiently close to the center to create a strong central concentration, which, in turn, may modify the properties of the bar. More violent evolution can take place during interactions, so that some disc substructures can be either formed or destroyed in a time scale which is small compared to a Hubble time. These include spirals, bars, bridges, tails, rings, thick discs and bulges. In some cases interactions may lead to mergings. We briefly review comparisons of the properties of ...
Youngkwang Unit 3,4 and Ulchin Unit 3 and 4 have had problem of the KSNP Steam Generator due to a severe fretting wear on the tube. In particular, the wears were localized and concentrated in the upper part of U-bend of the Central Cavity region. At the upper tube bundle Central Cavity, the fluid flow velocities and void fraction are very high, because the steam is made by high heat transfer at secondary region. Also, this region is affected easily by fretting wear due to it's unsupported span is longer than another regions. The fretting wear is assumed to be result of Flow-Induced Vibration (F. I. V), which can occur by many mechanisms. EFDP was added to UCN 5,6 for prevent fretting wear by the SEC LCC and DSHIC, a company of design and manufacture of the steam generator, respectively. In order to evaluate the efficacy of EFDP, ANSYS and ATHOS-3 Code were used. From sensitivity analysis and calculation results, Density and Velocity into the Central Cavity are reduced after ...
Youngkwang Unit 3,4 and Ulchin Unit 3 and 4 have had problem of the KSNP Steam Generator due to a severe fretting wear on the tube. In particular, the wears were localized and concentrated in the upper part of U-bend of the Central Cavity region. At the upper tube bundle Central Cavity, the fluid flow velocities and void fraction are very high, because the steam is made by high heat transfer at secondary region. Also, this region is affected easily by fretting wear due to it's unsupported span is longer than another regions. The fretting wear is assumed to be result of Flow-Induced Vibration (F. I. V), which can occur by many mechanisms. EFDP was added to UCN 5,6 for prevent fretting wear by the SEC LCC and DSHIC, a company of design and manufacture of the steam generator, respectively. In order to evaluate the efficacy of EFDP, ANSYS and ATHOS-3 Code were used. From sensitivity analysis and calculation results, Density and Velocity into the Central Cavity are reduced after the EFDPs ...
Decreasing the aperture of a solar central receiver operating at high temperatures contributes significantly to the increase of the efficiency of energy absorption. However, decreasing the aperture also decreases the collection efficiency. A simple solution is using a 3D-CPC as secondary element for augmenting the energy collection, while the aperture can remain relatively small. Nevertheless, the receiver aperture as well as the secondary concentrator are usually rather large. For practical considerations an approximate solution may be chosen at times, designing the concentrator by a series of truncated cones. However, in particular cases, the solution of truncated cones remains expensive and unpractical and therefore the authors designed a CPC approximated by a series of trapezoidal planar facets. Under technical restrictions, there is an optimum for choosing the partition of the pure-CPC in truncated pyramids and the paper presents the method for a good ...
In an HTR plant high temperature components of Alloy 800 materials are subjected to temperatures from about 550 to 850degC in the long term; higher temperatures may occur in the short term. Thus the creep and stress-rupture parameters govern the design of these components. Since in recent years the scope of experimental data available for Alloy 800 materials has considerably increased, a new evaluation of the creep and creep-rupture properties was performed using a data bank computer. The relationships between the characteristics of the creep and creep-rupture behaviour and the metallurgical parameters were investigated by multilinear regression analyses. On the basis of the results of these analyses and after discussion in material expert committees new material specifications were determined for different types of Alloy 800. They were included into the draft standards DIN 17459 and DIN 17460 under the material standard nos. 1.4958, 1.4958 Rk and 1.4959. Besides ...
In an HTR plant high temperature components of Alloy 800 materials are subjected to temperatures from about 550 to 850degC in the long term; higher temperatures may occur in the short term. Thus the creep and stress-rupture parameters govern the design of these components. Since in recent years the scope of experimental data available for Alloy 800 materials has considerably increased, a new evaluation of the creep and creep-rupture properties was performed using a data bank computer. The relationships between the characteristics of the creep and creep-rupture behaviour and the metallurgical parameters were investigated by multilinear regression analyses. On the basis of the results of these analyses and after discussion in material expert committees new material specifications were determined for different types of Alloy 800. They were included into the draft standards DIN 17459 and DIN 17460 under the material standard nos. 1.4958, 1.4958 Rk and 1.4959. Besides ...
The 1.04 GeV-proton elastic scattering from /sup 40/Ca is studied in the framework of the coherent density fluctuation model (CDFM). The calculations are carried out in the Glauber theoretical scheme with three different charge densities. It is shown that: i) the account of the flucton correlations leads to results considerably different from those obtained in the independent particle Glauber approach (IPGA); ii) in contrast to the case of IPGA the use of a more realistic density improves the agreement of CDPM-results with the experimental data.
The 1.04 GeV-proton elastic scattering from "4"0Ca is studied in the framework of the coherent density fluctuation model (CDFM). The calculations are carried out in the Glauber theoretical scheme with three different charge densities. It is shown that: i) the account of the flucton correlations leads to results considerably different from those obtained in the independent particle Glauber approach (IPGA); ii) in contrast to the case of IPGA the use of a more realistic density improves the agreement of CDPM-results with the experimental data. (orig.).
We calculate quark-antiquark potentials using the relationship between the expectation value of the Wilson loop and the action of a probe string in the string dual. We review and categorize the possible forms of the dependence of the energy on the separation between the quarks. In particular, we examine the possibility of there being a minimum separation for probe strings which do not penetrate close to the origin of the bulk space, and derive a condition which determines whether this is the case. We then apply these considerations to the flavoured resolved deformed conifold background of Gaillard et al. We suggest that the unusual behaviour we observe in this solution is likely to be related to the IR singularity which is not present in the unflavoured case.
To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.
To estimate the waste management needs of a fusion power reactor, a scheme for handling radioactive waste from a fusion plant has been devised. The handling scheme proceeds with radioactive waste, primarily from blanket replacement, being stored on-site; waste in cooled and shielded casks is then isolated off-site; finally, the materials are recycled. Using activities and component lifetimes supplied by designers, several conceptual fusion power reactors have been analyzed and their waste streams compared to fission reactors with regard to total activity, specific activity, and lifetimes of activity.
Bubbly and slug flows have been analyzed using the afore-mentioned techniques. An image series of bubbly-slug flow is shown. The image separation time is 17 ms, and the total flow length is {approx} 10 cm. A circular eddy pattern that follows the slug can be readily seen and tracked, although reliability is low due to motion in the transverse direction. This motion also adds considerable error to the velocity measurements using image recognition technique. This will increase the reliability and accuracy of the tracking method.
The House Committee report describes the purpose, background, committee considerations and findings, and correspondence relating to H. Con. Res. 50, which is intended to encourage the president to pursue international negotiations relating to the ozone layer. The intent is to develop an international protocol and regulatory framework that will protect the stratosphere from the effects of chlorofluorocarbons. The report notes that some nations have already taken unilateral remedial steps, but argues the benefits of a negotiated agreement worldwide.
In the last two years, the VDMA work group 'Functional security' compiled a qualitative and quantitative procedure for the determination and evaluation of turbo-machine specific risks. With the calibrated risk graph for turbo-machines the requirements (Safety Integrity Level SIL) to the protective functions for turbo-machines (steam turbines, gas turbines, generators and compressors) were determined. With consideration of the legislation, the work group compiled a recommendation for the renewal and/or reconstruction of protective functions with old facilities.
Volume VII of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the tritium transport model documentation. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Volume VI of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the groundwater flow model data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Volume IV of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the hydrologic parameter data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Volume II of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the potentiometric data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
The heating history of a droplet during its flight can be divided into two phases: (a) the initial phase when evaporation, although it occurs, does not change the heat balance of the droplet much (the case considered in our previous paper and (b) the final phase when the cooling due to evaporation balances the heat flux from the plasma. The later phase is considered in Chen's comment. In our reply, a very straightforward consideration demonstrates that even in the final phase of the droplet flight, the 'rocket' effect can be significant. (reply)
Different calculated models are presented for turbulent break-off flows and their classification, reflecting the sequence of historical development. The study was done based on equations of viscous liquid of the Navier-Stokes type with development of special phenomenological models of turbulence which take into consideration real properties of the break-off flows based on simpler models of flow presented in the work. In order to calculate two-dimensional turbulent flows, a method of viscous-nonviscous interaction is used. It employs numerical solutions for nonviscous flow and integrated methods of calculating the dissipative region. This method can be extended for calculating the transonic break-off flows, and also break-off in an incompressible fluid when there is cavitation.
We propose triplet superconductors, such as ruthenates, as prospective materials for qubit construction. The vectorial nature of the order parameter in triplet superconductors makes it conceptually easy to estimate the performance of the qubits. The Cooper condensate of pairs in triplet superconductors has all the attributes of Bose-Einstein condensates and should facilitate long decoherence times for these qubits, relative to other vectorial schemes for qubits, such as small ferromagnets. There are other benefits, which the superconducting state provides for requirements such as entanglement between qubits via the proximity effect, etc. We consider these benefits in detail, although our consideration is only preliminary and further experimental and theoretical research will undoubtedly introduce correctives.
The Atomic Energy commission of Syria (AECS) is nominated by Syrian legislation as the regulatory authority in respect of radiation protection and safety and security of radioactive sources. In addition AECS is providing a wide range of Technical Services (TS) through its various departments. In this paper, the cooperation and coordination between the regulatory authority and the providers of technical services in Syria are described. The adjustment of the regulatory programme as to make maximal use of the available technical resources is presented. It was shown that this relationship does not jeopardize the effective independency of the regulatory authority which is maintained by keeping the regulatory decisions based on pure regulatory considerations. (author)
Delivering the promise of personalised medicine is the challenge that the current generation of scientists face. The variations in human physiology and disease are considerable, and designing appropriate strategies to deliver what has been promised will require access to tissue from a large number of volunteers. The NHS provides an ideal infrastructure for sample acquisition, but requires two things to make this available?public consent and support for extra manpower and administration. There is a disconnection between the NHS and tissue based research that needs to be addressed on a number of levels to provide a translational platform. This should enable the path to be beaten to provide the ideal tailored treatment for future patients; one that preserves quality of life by curing the dise...
Considerable potential exists for increasing the annual efficiency of line-focus collectors by reducing receiver heat losses. Five alternate receiver designs are compared with a standard design. The comparison is based on annual collector-field efficiency using optimized receiver designs. Of the receivers studied, the all-glass design and the cavity design provide the greatest increases in efficiency. Average fluid temperatures range from 200/sup 0/ to 450/sup 0/C. As a guide for further study, areas of uncertainty and potential problems are identified.
A consistent statistical theory of the crystal-liquid phase transition is developed, being based on a method which takes into account liquidlike fluctuations in crystals and solidlike clusters in liquids. It is shown that degenerate fluidlike droplets have a finite number density at zero temperature, while nondegenerate fluctuations disappear when the temperature goes to zero. The existence of a melting point is proved. This method, which takes into consideration the heterophase fluctuations, provides the possibility of describing metastable states such as a supercooled liquid or an overheated crystal. Conditions for the existence of metastable states are found. The liquid-glass transition can also be described by the method presented here.
The theoretical hardness against total dose of the six-transistor SRAM cell is investigated in detail. An explicit analytical expression of the maximum tolerable threshold voltage shift is derived for two cross-coupled inverters. A numerical method is used to explore the hardness of the read and write operations. Both N- and P-channel access transistors designs are considered and their respective advantages are compared. The study points out that the radiation hardness mainly relies on the technology. Results obtained with the very robust Gate-All-Around process are finally presented.
The measurement of K(alpha)/K(beta) X-ray intensity ratio indicates the excitation process and the chemical state of the atom examined. Theoretical considerations on the origin of this property are presented. The difference of these ratios following photoionization and electron capture are calculated by a computer code generating transition matrix elements. The theoretical assumptions involved in the codes are tested by comparing the experimental and calculated data concerning 3d transition element atoms. (D.Gy.).
The absorption, emission and magnetic circular dichroism spectra of the anionic complex (Cp_3Pr. NCS)"- were measured at room and low temperatures. On the basis of these spectra the electronic structure in the f-f range could be derived. The parameters of an empirical Hamiltonian were fitted to the experimentally determined crystal field splitting pattern. Compared with the previously examined neutral Cp_3 Pr.X complexes the quadratic crystal field parameter B_0"2 is considerably reduced.
We summarize our lattice QCD study of the form factor at zero recoil in the decay {bar B} {yields} D*{ell}{bar {nu}}. After careful consideration of all sources of systematic uncertainty, we find, h{sub A{sub 1}}(1) = 0.913{sub -17-30}{sup +24+17}, where the first uncertainty is from statistics and fitting while the second combined uncertainty is from all other systematic effects.
We have described the x-ray optics and beamline performance of the ANL X6B beam line at the NSLS. Considerable flexibility has been built into the beam line to accommodate a wide range of x-ray diffraction, scattering, and spectroscopy experiments with various requirements. We presented selected examples of experimental results and showed that with the high intensity, high energy resolution, high-q resolution, and energy tunability, the X6B beam line has become a versatile facility.
In this note it is suggested that binuclear platinum(II) complexes with a solely inorganic bridging pyrophosphito ligand also possess many of the complementary advantages of inorganic and organic dyes. They are evaluated for their potential use as a luminescent solar concentrator material. The disadvantages include: the high cost of platinum; the absorption spectra in solution shows a weaker absorption at 452 nm which may cause reabsorption of emitted light; the positions of the absorption and emission maxima are not at the optimal wavelengths for absorption of sunlight and emission to a solar cell. In spite of these drawbacks the author believes the platinum complexes merit consideration for fabrication of solar concentrator devices.
Theoretical development for temperature measurements via narrow line, infrared absorption of carbon dioxide (CO{sub 2}) is presented. The proposed technique is based on rapid-scanning of two adjacent absorption line shapes. Spectroscopic considerations for sensitivity to temperature measurements are discussed. Several line pairs are evaluated, and the R(58) and R(60) transitions of the (00{sup 0}1){l_arrow}(00{sup 0}0) band are suggested for use in high temperature measurements for combustion systems.
Single and selective pole tripping schemes may be used to maintain a desired level of system integrity while minimizing transmission line expenditures. In general, these schemes will be most effective on those portions of the system where relatively few interconnections exist. While selective pole tripping may superficially appear to provide more margin than single pole schemes in the preservation of system stability, it seems unlikely that in those actual applications where single pole tripping is warranted that selective pole tripping will provide any significant advantages.
The effect of high energy neutron irradiation (E > 1 MeV) on the superconducting transition temperature, Tsub(c), of the A-15 compound Mo_3Os is reported. Tsub(c) was found to decrease with increasing neutron dose, but at a rate considerably less than observed in other A-15 compounds composed of non-transition metals. The results lend support to the idea that the effect of ordering on Tsub(c) is smaller for A-15 compounds composed only of transition metals than those composed of transition and non-transition metals. (author).
Design methods and parameters are described which are addressed when considering consequences of a postulated pipe rupture event in a nuclear plant design. Parameters discussed are break opening time and size, resultant blowdown characteristics of the effluent from the broken pipe, jet reaction and impingement loading, pipe motion, and pipe impact loading on steel and concrete structures. The impact the various parameters have on overall plant designs and conservatisms inherent in each consideration are evaluated in a qualitative nature. Finally, recommendations are provided for each parameter discussed for further evaluation and study.
The mechanism of abrupt increase of the giant magneto impedance (GMI) ratio in the ion irradiated Co-based amorphous ribbon has been investigated. The grazing incident X-ray diffraction and transmission electron microscope were used to characterize the samples before and after ion irradiation. The GMI-ratio considerably increased in the ion irradiated samples and the GMI response showed strong dependence on the driving frequencies. The Barkhausen noise (BN) signals are increased for the Ar ion irradiated sample with dose of 1x10^1^7 ion/cm^2. The results are interpreted in terms of GMI variation associated with domain wall dynamics.
Due to the general market conditions, the construction of steam turbines was greatly reduced in 1987. As in 1986, it came to a downward movement. This situation will heighten in the coming years. The exploitation of devices, which are available by way of the development of EDP in computation, construction, production and operation, leads to considerable improvements. These improvements can only be employed gradually, due to the reduction in production. However, technological progress can be used economically in part in the restoration of old installations. Here turbine construction, the thermodynamical interpretation of gas and steam turbines, developments in the field of conduction technology, piping and materials are described. Also improvements in operation security and operation supervision of the installations is treated, as well as service and maintenance of the plants. (BR) With 131 refs.
After presenting a general account of the observed global properties of single stars of low, intermediate, and high mass, together with their theoretical Hertzsprung-Russell diagram evolution, attention is given to the observed properties of various evolved close binaries and to an assessment of the value of comparisons between observation and crude theory in characterizing the physics of mass transfer within interacting binary systems. Detailed consideration is then undertaken of such topics as stellar evolution in globular clusters, interior star changes due to nucleosynthesis and mixing, asymptotic giant branch stars of intermediate mass, the response of white dwarfs in binary systems to mass accretion, and scenarios for binary star evolution tending toward close white dwarf pairs.
Room-temperature phosphorescence (RTP) has generated considerable interest over the past several years. Several materials have been used to induce RTP from a variety of compounds. However, there is still a need to test additional materials and experimental conditions for RTP so the maximum sensitivity and selectivity can be obtained. In this work, three solid surfaces and several experimental conditions were tested for RTP of nitrogen heterocycles and aromatic amines. Nitrogen heterocycles and aromatic amines are an important class of compounds as shown by work in areas such as environmental research and coal liquefaction research. 18 references.
The risk analysis was carried out in consideration of conditions prevailing at the Kalkar site analogous to the investigations in phase A of DRS (German Reactor Study). Earthquake design loads include the probabilities of upper deviations of the site intensities to be expected. The calculations of dynamic loads for select buildings are made using models and computational methods. Component analyses were performed analogous to DRS for the supports of large components, supports of the roof construction of the reactor building taking into account support reserves due to plastic work capacity, wall disks in steam generator buildings and switchboard plant buildings. (DG).
We have explored vibrations of a single-degree of freedom oscillator with a magneto-rheological damper subjected to kinematic excitations in a high frequency limit. Using fast and slow scales decoupling procedure we derived an effective damping coefficient in the limit of high frequency excitation. Damping characteristics, as functions of velocity, change considerably especially by terminating the singular non-smoothness points. This effect was more transparent for a larger control parameter which was defined as the product of the excitation amplitude and its frequency.
In the power station West Block 2 at Voerde (Federal Republic of Germany), cracks in the final stage of the shaft were determined at the ND1 rotor of the 350 MW condensation tube was determined. A purely mechanical preparation of the crack was not possible due to the depth of the crack. A substitute rotor was not available. A repair solution was developed covering a welding of a new shaft section to the existing rotor. The authors of the contribution under consideration report on the damage, cause of the damage, repair solution and the process of repair.
Lithium orthosilicate (Li_4SiO_4) powder was synthesized by the solid-state reaction of lithium oxide with amorphous silica, and the effects of fabrication parameters on the structural characteristics of the product were investigated. Processing considerations such as milling media, drying technique, calcination time and temperature, pressing behavior, sintering time and temperatures, and impurity concentration were addressed. The initial powder particle size was observed to be important in achieving high sintered density, with densities as high as 98% TD achieved with a particle size of approximately 1 #mu#m. 9 refs., 6 figs.
The response of a real time neutron dosemeter using a thin LiF target sandwiched between tow parallel surface barrier semiconductor detectors is studied for different neutron distributions and different angles of incidence. Calculations of the response function defined for a simultaneous detection by the two detectors of the particles emitted when the reaction "6Li(n,t)#alpha# occurs in the target are fulfilled by geometrical considerations of the reaction kinematics and the differential cross section variations. Finally, the efficiency of the studied detection systems is analyzed for dosimetric uses. (author).
The doping of deuterated polyparaphenylene (C/sub 6/D/sub 4/)sub(n) with AsF/sub 5/ has been investigated by real time neutron diffractometry at 100, 400 and 820 mbar AsF/sub 5/ pressure. The reaction appears to be diffusion controlled. Evidence for one doped phase with partial crystalline order was obtained. Structural considerations suggest two polymer chains plus one dopant ''string'' as the repetitive unit.
Factors influencing the rooting-potential of stem cuttings of conifers were studied for the purpose of improving methods of rapid vegetative propagation. Within the bounds of hereditary limits, root regeneration depends, to a considerable extent, on the qualities of rooting-media, date of cutting excision, age and physiological conditions of the stock plant, age of the cutting-wood, its position on the plant, and chemical treatment. Hardwood cuttings, which have a relatively high content of endogenous auxin and carbohydrates, and morphological root initials, gave the best results. This method made it possible to increase the growth rate of cuttings 2.5-5 times that of cuttings taken from shoots of current growth. (Refs. 21).
The authors present a guide to the imaging of facial fractures. It is illustrated with conventional radiographs and computed tomograms; the magnetic resonance images primarily suggest the potential applications of this technique. This book provides a source of imaging information on facial trauma. A section on pertinent anatomy is followed by a systematic discussion of the common isolated and complex facial fractures. Perspectives are offered on some commonly seen but infrequently described relationships, such as the tripod-LeFort II association. Consideration is also given to related soft-tissue injuries. The book includes a brief chapter on the type and utility of supplementary imaging studies in the evaluation of those intracranial injuries that may occur concurrently.
A study was made on the effect of 3.5 MeV electron irradiation on the properties of light-emissive structure based on GaAlAs. It is shown that a considerable decrease in the emitted light intensity as a result of electron irradiation not accompanied by changes in recombination- and electric properties of the mentioned structures. It is established by the electron-microscopy and Auger-spectroscopy meazurements that electron irradiation causes the occurrence of regions of free aluminium clusters on the external surface of the structure n-layer. The number and the sizes of the regions depend on the electron doze. It was assumed that the mentioned regions can play a role of attenuation filter for the light emitted by the structure.
The paper discusses some of the assumptions and methods employed for the control of ionizing radiation in the specifications for the civil construction of a planned free electron laser facility based on a 200 MeV, 5 mA superconducting recirculation electron accelerator. Consideration is given firstly to the way in which the underlying building configuration and siting aspects were optimized on the basis of the early assumptions of beam loss and radiation goals. The various design requirements for radiation protection are then considered, and how they were folded into an aesthetically pleasing and functional building. copyright 1997 American Institute of Physics.
The general types of pumped-storage plants and considerations for determining their need, use, and selection are presented. A brief discussion of TVA's experience on two pumped-storage schemes is included. Pumped-storage plants have become an integral part of many hydropower systems. Most of these systems use pumped-storage plants to meet power requirements during the peak load demands. In any application, large or small, the expected load demand and supply source must be identified to select the best scheme required for the particular system.
Originally designed exclusively for peak load covering, pumped storage plants are now faced with new challenges brought about by the deregulation of the electricity market and the substantial growth of wind power capacity. Today's pumped storage plants are started more frequently and often for shorter periods of time. The grid controlling tasks have increased the importance of the role played by this type of power plant and improved sales considerably. But the operational demands have grown substantially as well. This paper discusses the ensuing adaptation of power plant operation as well as options available to power plant operators. (orig.)
The debate about whether or not animals have foresight has focused on whether animals can be shown to have episodic future thinking, that is the ability to travel mentally in time and see themselves in the future. This focus has distracted from consideration of other forms of foresight that animals demonstrate. We propose a framework for examining future-oriented behaviours and then discuss the evidence for future thinking in animals. In the final section we examine some perspectives of future thinking and suggest that there are future-oriented capabilities of animals that do not involve mental time travel but may yet involve future thinking which deserve further investigation. PMID:20522320
Micropropagation methods are described for the production of clonal lines from Eucalyptus marginata (jarrah) seedlings. Nodal explants from mature trees can also yield shoot cultures, but a high frequency of contamination occurs among such explants. Uncontaminated callus cultures can be produced from mature trees by culturing stamen filaments and shoots can subsequently be regenerated from this callus. The rooting percentage of shoot cultures from either nodes or stamen callus of mature trees is low compared with that from seedling explants. Considerable variation was observed between trees in the ability of stamen callus to regenerate shoots and in the frequency of rooting. (Refs. 27)
Methods are described for the production of callus and subsequent shoot and root induction and multiplication using stamen filaments, nodes of young stems of mature trees or cotyledon petioles. A high frequency of contamination occurred using nodal sections from mature trees, whereas up to 100% sterility was obtained with cotyledons and stamens. The rooting % of shoot cultures from nodes or stamen callus was low compared with that of shoots from seedling callus. Considerable variation was observed between clones from different trees in their ability to produce shoots and roots. 27 references
Coal-water-slurry (CWS) engine tests designed to evaluate a new accumulator-based injection system are described in this paper The new injection system was found to improve CWS burnout considerably at both full and part engine loads. The peak cylinder firing pressure when operating with CWS was no higher than when operating with diesel oil. These data demonstrates the improved engine performance that can be achieved with the accumulator-based injection system.
The cold fusion reactions leading to superheavy elements with Z=104-116 has been discussed in our model recently [5]. Presently we shortly discuss our model and extend our consideration to fusion reactions ("8"6Kr, "8"7Rb, "8"8Sr)+"2"0"8Pb and "8"6Kr+"2"0"9Bi leading to elements with Z=118-120. The available experimental cross-section data for the reactions are well described.
The conference paper gives a short description of the strategies within Statoil Gas Transport for pipeline condition monitoring and control. This is done for ensuring that the pipeline integrity can be maintained during all phases from construction to operation. Efficient condition monitoring and control can only be performed if the total pipeline integrity is taken into consideration such as design conditions, experience, environmental information, and general improved knowledge or the like for determining the requirement of inspection. Such philosophy will ensure the pipeline integrity better as corrective actions can be taken at a very early stage before any damage to the pipeline system have developed. 1 fig.
In this paper the humidification?dehumidification desalination process is studied and its performance optimized using mathematical programming. An advantage of this method is consideration of the simultaneous effect of various parameters on process performance. An NLP system model is solved for three objective functions: minimization of specific thermal energy consumption, maximization of productivity and maximization of condenser heat recovery. The solutions have been improved especially from a productivity point of view in comparison with previous studies. The productivity objective function leads to the best solution if there is no limitation for the humidifier inlet water temperature. Otherwise, the specific energy objective function seems to be better than others. In the next step the...
The partial project SR 2039/4 investigates organizational demands and factors of the man-organization interface. Thee study is divided into the sections inventory of rules and guidelines; evaluation of organizational structures and modes of operation, and working out of demand characteristics and evaluation criteria. The objective consists in representing, analyzing and evaluating the efficiency structure of sequence organization, and deriving practice-relevant concept proposals in order to optimize the man-organization interface. In this regard, the working out of control mechanisms for the evaluation of organizational sequences is of considerable importance as a kind of working aid. (orig./DG).
Copper alloys are a suitable tubing material for turbine condensers and heat exchangers. Due to problems with corrosions copper alloys increasingly are displaced by high-grade steel and titanium. Blockages and surface formation in the pipes, disturbance of the oxide coating formation, erosion and quality faults with the production are the causes for the corrosion. In the contribution under consideration counter measures are designated for the solution of the problems with corrosions. The application limits for different copper alloys are designated. Recommendations for the optimized operation are given.
The prevailing hypothesis of linear extrapolation from high to low radiation doses without any threshold level is being questioned more and more strongly for radiobiological and epidemiological reasons and, consequently, also on socio-economic and ethical grounds. A cost-benefit analysis based on scientific facts and made plausible to the general public, concentrating on a comparison with demonstrable natural and manmade risks, most probably would result not only in the permissible limits being raised by a considerable margin, but also in billions of costs saved, and in greater acceptance of all peaceful uses of radiation, nuclear power included. (orig.)
The phase transition is a performance measure of the sparsity-undersampling tradeoff in compressed sensing (CS). This letter reports, for the first time, the existence of an exact phase transition for the $\\ell_1$ minimization approach to the complex valued CS problem. This discovery is not only a complementary result to the known phase transition of the real valued CS but also shows considerable superiority of the phase transition of complex valued CS over that of the real valued CS. The results are obtained by extending the recently developed ONE-L1 algorithms to complex valued CS and applying their optimal and iterative solutions to empirically evaluate the phase transition.
The paper develops a new class of financial market models. These models are based on generalized telegraph processes: Markov random flows with alternating velocities and jumps occurring when the velocities are switching. While such markets may admit an arbitrage opportunity, the model under consideration is arbitrage-free and complete if directions of jumps in stock prices are in a certain correspondence with their velocity and interest rate behaviour. An analog of the Black-Scholes fundamental differential equation is derived, but, in contrast with the Black-Scholes model, this equation is hyperbolic. Explicit formulas for prices of European options are obtained using perfect and quantile hedging.
V.M. STRUTINSKY's semi-classical method is the most precise to determine the energy of the different states along the fission way. The double-humped fission barrier explains fission isomerism. V.M. STRUTINSKY's barrier explains the ''intermediate structure'' observed in the cross section under the threshold; it provides also the observed effect of ''vibrational resonances'' with an interpretation. Taking an asymmetry parameter in consideration, a triple-humped fission barrier seems to be essential now for the light actinides. There is still a microscopic fission barrier to be explained.
Acute agitation is a frequent reason for emergency psychiatric intervention. It is important to intervene early to avoid escalation of agitation to aggression. Reducing risk by using effective treatments will result in fewer instances of seclusion and restraint, and fewer injuries to staff and patients. This paper will first review the epidemiology of aggressive behavior and mental disorders, followed by a discussion of assessment and diagnostic considerations. The pathophysiology of safety risk is discussed within the context of the model of the "triune brain." Pharmacological treatment strategies for acute episodes of agitated behavior will be discussed in detail. This includes newer formulations of novel antipsychotics such as liquids and rapidly disintegrating tablets, as well as intramuscular preparations. PMID:15335224
Some results on mechanical property study of copper and titanium subjected to impact load and next to neutron irradiation are presented. It was shown that shock wave influence involves a substantial shape change of the stress-strain diagram and of respective mechanical characteristics. Yield- and ultimate strength were substantially increased, as well as hardness with a considerable drop of plasticity. Also a heat stability of copper and titanium specimens was studied after being treated with shock-waves and neutron radiation. Results are given of electron microscope study of titanium structure sfter explosion hardening, which caused decomposition of hydride segregations in titanium and increased dislocation density.
It may be stated that for the calculation of the heat transfer coefficients for natural convection cooling of large-diameter finned surfaces it is necessary to take in consideration the effects of the fin length, fin material and of the azimuthal angle around the cylinder. The present results replace earlier less accurate correlations gained from the same measurements. The new, better correlation was elaborated with the aid of the improved method of evaluation of multiple parameters of a measurement matrix of multiple dimension (one dimension for each parameter), rendering the sum of the squares error a minimum at the same time for the complete matrix. 5 references.
Parameters of permanent magnets result from the combination of intrinsic properties such as saturation magnetization, magnetic exchange, and magnetocrystalline energy, as well as microstructural parameters such as phase structure, grain size, and orientation. Reduction of grain size into nanocrystalline regime (#approx# 50 nm) leads to the enhanced remanence which derives from ferromagnetic exchange coupling between highly refined grains. In this study the fundamental phenomena, quantities, and structure parameters, which define nanophase permanent magnets are presented and discussed. The theoretical considerations are confronted with experimental data for nanocrystalline Sm-Fe-N type permanent magnets. (author)
Purpose - This paper aims to describe the technology and applications of nanocomposite materials. Design/methodology/approach - This paper discusses products, applications and technological developments in polymer, ceramic and metal nanocomposites. It concludes with a brief consideration of electronic component applications. Findings - It is shown that polymer nanocomposites and the materials used in their production are commercially available and finding applications in several industries, including automotive, military, food, electronics and leisure, due to their enhanced mechanical, electrical and thermal properties. Ceramic and metallic nanocomposites are at an earlier stage of development and a critical issue to resolve is optimising the dispersion of nanomaterials in the matrices. Pa...
There is proposed the nonlinear model of dose dependence saturation of the yield strength on the base of the vacancy and interstitial barrier interaction in this work. Processes of mutual recombination of vacancy and interstitial barriers and formation of vacancy and interstitial clusters are taken into consideration. In the framework of the model, the analytical equations corresponding to the evolution of the barrier densities and yield strength are obtained. It is shown that the yield strength of irradiated materials decreases with the increasing intensity of barrier recombination processes, the dependence being nonlinear. Also it is shown that the model is valid both for low doses and large doses on the stage of radiation hardening.
This paper presents a framework for creating a common spatial canvass that can bring together considerations of resource availability, infrastructure reliability, and development costs while strategizing renewable energy investment. We describe the underlying models and methodologies that annotate an investment plan for potential sites over a time-period with costs and constraints which may be imposed on distance from infrastructure, system impact on infrastructure, and policy incentives. The framework is intended as an enabler for visualization, optimization and decision making across diverse dimensions while searching for lucrative investment-plans.
Microorganisms are ubiquitous in subsurface environments although their populations sizes and metabolic activities can vary considerably depending on energy and nutrient inputs. As a result of their metabolic activities and the chemical properties of their cell surfaces and the exopolymers they produce, microorganisms can directly or indirectly facilitate the biotransformation of radionuclides, thus altering their solubility and overall fate and transport in the environment. Although biosorption to cell surfaces and exopolymers can be an important factor modifying the solubility of some radionuclides under specific conditions, oxidation state is often considered the single most important factor controlling their speciation and, therefore, environmental behavior.
Voestalpine AG (Linz, Austria) produces heavy steel for steam turbines, compressors for the promotion of oil and gas as well as for the chemical industry, mechanical engineering and for the offshore technology. A weight range between 1 and 200 tons can be covered. The author of the contribution under consideration is limited to characteristics which have to be managed by a large steel foundry within the range of the steam power plants. This is described on the basis of produced steam turbines for power stations in the highest performance segment (1,600 MW).
The DP West Plutonium Facility operated by the Los Alamos National Laboratory, Los Alamos, New Mexico, was decontaminated between April 1978 and April 1981. The facility was constructed in 1944 to 1945 to produce plutonium metal and fabricate parts for nuclear weapons. It was continually used as a plutonium processing and research facility until mid-1978. Decontamination operations included dismantling and removing gloveboxes and conveyor tunnels; removing process systems, utilities, and exhaust ducts; and decontaminating all remaining surfaces. This report describes glovebox and conveyor tunnel separations, decontamination techniques, health and safety considerations, waste management procedures, and costs of the operation.
A short-chain neurotoxin Pseudechis australis a (toxin Pa a) was isolated from the venom of an Australian elapid snake Pseudechis australis (king brown snake) by sequential chromatography on CM-cellulose, Sephadex G-50 and CM-cellulose columns. Toxin Pa a has an LD50 (intravenous) value of 76 micrograms/kg body wt. in mice and consists of 62 amino acid residues. The amino acid sequence of Pa a shows considerable homology with those of short-chain neurotoxins of elapid snakes, especially of true sea snakes. PMID:4091794
The aim of the present is to consider the influence of pr equilibrium processes on the activation cross-sections of "2"7 Al(n,p) "2"7 Mg, "5"1 V(n,p) "5"1"m Ti, "8"8 Sr(n,p) "8"8"m Rb, "9"4 Zr(n,p) "9"4"m Y and "9"7"Mo(n,p) "9"7"m Nb in the neutron energy range 13 to 15 MeV. Comparison with recent measurements is given for all considered isotopes. 2 figs., 1 tab.
The restricted temperature stability of the synthetic thermal oil which is used as heat carrier fluid in parabolic trough collectors so far limits the live steam parameters in the steam cycle to approximately 375 Celsius. In order to break through this limit, already for quite some time it is researched to replace the thermal oil by boiler feeding waters and to accomplish the evaporation in the collectors. The contribution under consideration gives an overview on the direct evaporation concept and summarizes the past operational experiences. Moreover, the challenges with the integration of this technology in a steam turbine cycle are elaborated.
Ascochyta blight causes significant yield loss in pulse crops worldwide. Integrated disease management is essential to take advantage of cultivars with partial resistance to this disease. The most effective practices, established by decades of research, use a combination of disease-free seed, destruction or avoidance of inoculum sources, manipulation of sowing dates, seed and foliar fungicides, and cultivars with improved resistance. An understanding of the pathosystems and the inter-relationship between host, pathogen and the environment is essential to be able to make correct decisions for disease control without compromising the agronomic or economic ideal. For individual pathosystems, some components of the integrated management principles may need to be given greater consideration tha...
Sessions covered economic and management, advance control technologies (including pulverized coal dynamic balancing-activator and control strategy by B. DeMarcy and X.Ollat), nuclear technologies, environmental (including purge considerations for seasonal SCR systems by D.P. Evely, NOx and heat rate supervisory control at NRG-Huntley operations by G Lange, comparison of gypsum dewatering technologies at flue gas desulfurization plants by B.A. Perlmutter, beta gauge particulate monitoring by J.L. Arnold), improving performance at nuclear power plants, network security, and emerging applications.
This forum provided insights into Ontario's new smart meter program. Challenges related to implementing the smart meter program were reviewed, and various functional and operational considerations of the meters were considered. The implications and benefits of using real time metering systems were discussed along with issues related to energy conservation and demand management. Various communications technologies were considered in relation to smart metering program implementation. Issues related to pricing and pricing policies were also discussed. The conference featured 11 presentations, of which 2 have been catalogued separately for inclusion in this database. refs., tabs., figs.
During 2009, the Hilton M. Briggs Library, South Dakota State University, went live with MetaLib, a federated search engine from Ex Libris. This paper presents the implementation process, addresses resource accessibility issues, and suggests a number of resources that can be consulted about these issues. Readers can apply similar strategies to projects involving federated search systems, as many implementation projects involve the same basic considerations presented here. The author did not find any studies specifically focused on configurations of MetaLib resources, so this content should be singularly useful.
The nature of hydrothermal resources, their associated temperatures, geographic locations, and developable capacity are described. The parties involved in development, required activities and phases of development, regulatory and permitting requirements, environmental considerations, and time required to complete development activities ae examined in detail. These activities are put in proper perspective by detailing development costs. A profile of the geothermal industry is presented by detailing the participants and their operating characteristics. The current development status of geothermal energy in the US is detailed. The work on market penetration is summarized briefly. Detailed development information is presented for 56 high temperature sites. (MHR)
All power plant engineers face the problem of peak power demands. Pumped storage plants are used to generate peak load power by pumping up water utilizing off-peak energy of hydrothermal and thermonuclear plants. This is the first accessible text/reference to cover hydroelectric power generation with emphasis on engineering to meet peak power demands by means of pumped storge plants, tidal power plants, and low head power generation. Text covers hydrology, mechanical and electrical equipment, accessories such as penstocks and valves, and civil engineering considerations. Contains descriptions of several existing plants. Includes 200 diagrams and 50 photographs.
All power plant engineers face the problem of peak power demands. Pumped storage plants are used to generate peak load power by pumping up water utilizing off-peak energy of hydrothermal and thermonuclear plants. This is a reference to cover hydroelectric power generation with emphasis on engineering to meet peak power demands by means of pumped storage plants, tidal power plants, and low head power generation. Text covers hydrology, mechanical and electrical equipment, accessories such as penstocks and valves, and civil engineering considerations. Contains descriptions of several existing plants. Includes 200 diagrams and 50 photographs.
Thermal solar energy plants for water heating have experienced an enormous boom during the last years. Thus, a total of 200000 square metres of collector surface was installed on German rooves in 1991. This was three times as much as in the year before. And this trend of conserving natural resources by using the energy of the sun is still undiminished. (orig.)
The requirements for transporting high-current, negative-ion beams are presented with particular emphasis on applications involving negative-hydrogen-ion beams. In addition to the usual matching and steering problems, particular attention must be paid to beam emittance growth in the transport system. Depending on the application, a number of approaches have been developed using both magnetic and electric lenses. I discuss the design considerations for transporting and matching these beams to radiofrequency quadrupole accelerators, and present a survey of the various types of beamlines now used for negative-ion beams.
The requirements for transporting high-current, negative-ion beams are presented with particular emphasis on applications involving negative-hydrogen-ion beams. In addition to the usual matching and steering problems, particular attention must be paid to beam emittance growth in the transport system. Depending on the application, a number of approaches have been developed using both magnetic and electric lenses. I discuss the design considerations for transporting and matching these beams to radio-frequency quadrupole accelerators, and present a survey of the various types of beamlines now used for negative-ion beams.
The requirements for transporting high-current, negative-ion beams are presented with particular emphasis on applications involving negative-hydrogen-ion beams. In addition to the usual matching and steering problems, particular attention must be paid to beam emittance growth in the transport system. Depending on the application, a number of approaches have been developed using both magnetic and electric lenses. I discuss the design considerations for transporting and matching these beams to radiofrequency quadrupole accelerators, and present a survey of the various types of beamlines now used for negative-ion beams.
This plan outlines the procedures and operations used at LLNL's Site 300 for the management of the hazardous waste generated. This waste consists primarily of depleted uranium (a by-product of U-235 enrichment), beryllium, small quantities of analytical chemicals, industrial type waste such as solvents, cleaning acids, photographic chemicals, etc., and explosives. This plan details the operations generating this waste, the proper handling of this material and the procedures used to treat or dispose of the hazardous waste. A considerable amount of information found in this plan was extracted from the Site 300 Safety and Operational Manual written by Site 300 Facility personnel and the Hazards Control Department.
Malnutrition?in the form of insufficient energy intakes?affects millions of people worldwide and the negative impact of this kind of hunger is well acknowledged, not least by agronomists trying to increase yields to ensure a sufficient supply of food. This review focuses on another, more particular and ?hidden? form of malnutrition, namely mineral malnutrition. It illustrates the burden of disease that is caused by mineral deficiencies and the social and economic consequences they bring about. Mineral malnutrition has a considerable negative impact on individual well-being, social welfare and economic productivity. Agricultural scientists should keep the nutritional qualities of food in mind and?next to optimizing the agricultural properties of crops that are paramount for their adoption b...
The geothermal well-cost model developed by Sandia National Laboratories is being used to analyze the sensitivity of well costs to improvements in geothermal drilling technology. Three interim results from this modeling effort are discussed. The sensitivity of well costs to bit parameters, rig parameters, and material costs; an analysis of the cost reduction potential of an advanced bit; and a consideration of breakeven costs for new cementing technology. All three results illustrate that the well-cost savings arising from any new technology will be highly site-dependent but that in specific wells the advances considered can result in significant cost reductions.
The fact that South Africa had no commercially significant deposits of crude oil necessitated the early development of production of gasoline from coal which was present in abundance in low to medium grade in thick seams, the development of the process since the early 1950s is discussed. Both the Fischer Tropsch and Lurgi processes are used, and three large plants named Sasol One, Two, and Three have been completed. A flow diagram for the Lurgi process as used in these plants is included. Typical products and their properties resulting from the Sasol-type Synthol operation are presented in tabular form. Marketing considerations and economics of production of the Sasol products are discussed briefly. (BLM)
The fact that South Africa had no commercially significant deposits of crude oil necessitated the early development of production of gasoline from coal which was present in abundance in low to medium grade in thick seams, the development of the process since the early 1950s is discussed. Both the Fischer Tropsch and Lurgi processes are used, and three large plants named Sasol One, Two, and Three have been completed. A flow diagram for the Lurgi process as used in these plants is included. Typical products and their properties resulting from the Sasol-type Synthol operation are presented in tabular form. Marketing considerations and economics of production of the Sasol products are discussed briefly. (BLM)
This paper discusses design considerations for the recently introduced GaInP/GaAs monolithic tandem concentrator cell. The prototype device achieves a peak efficiency of 30.2% in a range of 140--180 suns, making this the first two-terminal device to demonstrate a verified efficiency exceeding 30%. At 425 suns the efficiency is still above 29%. The authors focus on the issues of grid design, top-cell thickness, and antireflectance coat. They also examine ways in which these aspects of the device may be modified to provide further performance improvements for future devices.
SO/sub 2/ concentrations in the Stuttgart air have been measured continuously since 1965. The two measuring points were located at the bottom of the Stuttgart city basin and 900 m east on the side of one of the surrounding hills. Long-term curves of pollutant loads have been established in consideration of meteorological parameters, as well as curves showing the average daily, weekly, and yearly pollution. The information thus gained may help to plan air pollution abatement measures in city planning.
We investigate the interplay between crossed channel final state interactions and the constraints from two-particle unitarity for the reactions J/{psi}{yields}V{pi}{pi} and VK anti K, where V is either {omega} or {phi}. Using a model where the parameters are largely constrained by other sources, we find that, although small, crossed channel final state interaction can influence the amplitudes considerably, in special areas of phase space. These results cast doubt on the inapplicability of unitarity constraints on production amplitudes as recently claimed in the literature. (orig.)
The method of an effective potential is used to investigate the possible types of evolution of vacuum shells in the Friedmann-Schwarzschild world. Such shells are assumed to emerge during phase transitions in the early Universe. The possible global geometries are constructed for the Friedmann-Schwarzschild worlds. Approximate solutions to the equation of motion of a vacuum shell have been found. The conditions under which the end result of the evolution of the vacuum shells under consideration is the formation of black holes and wormholes with baby universes inside have been found. The interior of this world can be a closed, flat, or open Friedmann universe.
Intermetallic compounds are regarded as highly promising for applications as high temperature structural materials. However, recent studies have demonstrated that a number of ordered alloys exhibit environmental embrittlement when tested in various environments at ambient temperature. When exposed to hydrogen gas or electrolytically charged with hydrogen, a significant ductility loss has been reported. The reaction of water vapor with reactive elements in the crack tip results in the generation of atomic hydrogen which diffuses from the surface to the interior and causes embrittlement. In this paper, the authors try to analyze the sensitivity of hydrogen embrittlement of ordered alloys based upon energetical considerations.
Emulsion explosives were discovered by Richard S Egley in 1961, but remained little known prior to rapid commercial development in the late 1970s. Their introduction has a significance that may in future be compared with the formulation of dynamite by Nobel in 1867 and the development of ammonium nitrate explosives in the mid 1950s. For the mining engineer emulsion explosives provide advantages of being inherently waterproof and having high strength with a high and stable velocity of detonation giving good fragmentation in hard rock. This is available at moderate cost, from an explosive that typically does not contain any self explosive ingredients and with fume properties that offer considerable advantages over other explosives. 2 figs., 1 tab.
Waste electrical and electronic equipment (WEEE) is recognized as a priority waste stream internationally, mostly due to their volume and hazardousness. This paper presents an analysis for the quantification of WEEE management cost for Greece, taking into consideration scenarios for reverse logistics network's development and WEEE volume scenarios. Transportation cost, which represents a major cost element for any reverse logistics network, is modelled with the use of mathematical programming, targeting towards the optimization of locations for the development of required intermediate storage infrastructures. Additionally, overall operational cost and recycling fees are estimated. PMID:21242175
The electric car has invited considerable interest: As many as four ministries had invited scientists and politicians of all conceivable fields to a national conference of strategy in November 2008 in order to discuss the national development plan on electrical mobility. The parallel exhibition showed vehicles of newer and older initiatives such as the small vehicle CityEl, modified vehicles in which batteries are installed instead of the rear seat, or the flagship which stated the advance of the electric cars, the Tesla Roadster.
Synthetic detergents constitute one of the most important water pollutants by contaminating the lakes and rivers through domestic and industrial use. Considerable information is now available for the adverse effects of detergents an aquatic fauna including fish, algae, and higher aquatic plants. Marked inhibition of germination in orchids and brinjals and of seedlings growth in raddish suggest that rapidly growing systems could be sensitive to detergent polluted water. The present study of the effect of linear alkyl benzene sulphonate on germination of the spores of a fern, Diplazium esculentum aims at the understanding of the effects of water pollution on pteridophytes and the development of spore germination assay for phytoxicity evaluation.
Considerable discussion has taken place during the last decade regarding the role of economic growth in determining environmental quality. Using data from 30 OECD countries for the period 1960-2003 and the nonparametric method of generalized additive models, which enables us to use flexible functional forms, this paper examines the environmental Kuznets curve hypothesis for carbon dioxide (CO2). We find that the reduction of coal share in energy use has a significant effect on CO2. Our results imply that economic growth is not sufficient to decrease CO2 emissions.
In this study, the state-of-the art for estimating LERF is considered for the regulatory risk-informed decisions. The consideration is mainly focused on (1) the relationship between Level 2 PSA and LERF evaluation methodology, (2) the standard requirements in terms of modeling preparation and the acceptance criteria based on the application capability II of ASME PRA standard, and (3) some pending issues for developing and proposing a simplified LERF model. This study is preliminarily presented and will be updated for establishing detailed evaluation scheme of extended MPAS (multi-purpose probabilistic analysis of safety) model and preparing the technical basis.
The operation of steam turbines is technically controllable. The manufacturers specify reliable operating ranges as well as demands on the implementation of steam turbines into the power plant process for the respective steam turbines. The VGB guidelines describe the generally valid procedures for the operation of steam turbines in detail. Important insights at some steam turbines are not or only insufficiently converted nevertheless. Damage and extended downtimes at revisions are the result. The author of the contribution under consideration describes some more and more occurring problems. Recommendations and suggestions are given with respect to the avoidance of such findings.
The first stage of the continuous coal hydrogenation unit has been used to test a number of coals with different processing strategies. This work has shown that conversion increases with product recycle, however after the second pass the increase is small but operability of the reactor is considerably improved. A kinetic model for the aromatic saturation of the recycle solvent in the second stage has been developed and will be used in the selection of conditions for oil upgrading processes. New insights into the structural composition of coal derived materials have been made due to the refinement of chromatographic or solubility separation analyses into routine operations and the development of a new technique in NMR spectroscopy.
Conformal radiation therapy represents a considerable and attractive challenge in oncology. Its aim is mainly to improve local control by increasing the dose with an acceptable rate of complications. This work overviews the world literature on this subject. The technical and theoretical requirements are highlighted. These requirements include a precise definition of the target volume by digital imaging (essentially CT scan), but also clear view of the target volume and the organs at risk, a specific collimation of the beam, 3-D dose calculations, optimization procedures, and a rigid immobilization of the patient with verification of his position. Moreover, the clinical applications of conformal radiation therapy are reviewed and discussed. (authors). 80 refs., 1 tab.
A confocal microscopy imaging system was devised to selectively detect Second harmonic signals generated by biological tissues. Several types of biological tissues were examined using this imaging system, including human teeth, bovine blood vessels, and chicken skin. All these tissues generated strong second harmonic signals. There is considerable evidence that the source of these signals in tissue is collagen. Collagen, the predominant component of most tissues, is known to have second order nonlinear susceptibility. This technique may have diagnostic usefulness in pathophysiological conditions characterized by changes in collagen structure including malignant transformation of nevi, progression of diabetic complications, and abnormalities in wound healing.
Consol R&D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-field: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.
Consol R&D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-fold: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.
A considerable time can elapse between initial selection of candidate plus trees and harvest of improved seed. The technique showing the greatest promise of shortening this interval is vegetative propagation. Stock plants are grown for two years from seed before the first propagation cycle begins and each plant can be bulked-up 300-500 times over two cycles. An initial stock of 2500 superior Sitka Spruce plants can be multiplied to yield between 300,000 and 750,000 rooted cuttings for forest use within four years from the start of propagation.
... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions Microchemical Engineer... Provides the information chemists and engineers need to evaluate the use of microreactors, covering the technical, operational, and economic considerations for various applications. AU$136.36 ex-GST Terms and Conditions Perry's Chemical Engin... Was: $199.95 inc gst NOW: $129.95 Special Price ...
We have made preliminary estimates of charged particles background at the 100x100 GeV Photon Linear Collider with ultimate luminosity. The charged particles background due to electromagnetic processes is located mainly in the small-angle range of the detector. At large angles, the number of background particles is much smaller. Analysis of the background (at least, in the range under consideration) shows that background conditions for the VLEPP-based Photon Linear Collider are better than at the VLEPP electron-positron collider. ((orig.)).
A variety of engineering and experimental applications require primary support structures which are self-centering. High mechanical strength, low-density, carbon fiber/epoxy matrix composite springs are used in unique planar, cylindrical, conical, and spherical configurations to self-center components. The sinusoidal and triangular-shaped composite springs are readily manufactured and assembled into component hardware. Design considerations, flexural strength properties, load bearing and centering data plus procedures for the manufacture of composite springs are presented.
Argon ions irradiation of 12% Cr steels and Fe/Cr alloys results in the hardening up to 10000 MPa. This value exceeds the hardening level even for martensitic transformation. Along with the increase of microhardness following irradiation the shape of X-ray graph of the affected materials changes considerable. Hardening value and behavior are determined by temperature radiation doze, preliminary ageing, extent of cold strain and alloying. The odserved phenomenon is supposed to be caused by irradiation-induced structural transformations. Reversibility of radiation hardening of the materials in question was observed.
Lung transplantation has become an accepted option for many patients with end-stage pulmonary diseases. Anesthesia and surgery following lung transplantation may be required for various diseases that may affect both systemic organs and the transplanted graft. When a patient with a lung transplant undergoes surgery, there is the potential for interference with lung function, depending on the type of intervention and its anatomical site. Accurate preoperative evaluation, an understanding of the physiology of the transplanted lung, proper airway instrumentation, individualized management of intraoperative ventilation, and fluid balance are essential for a positive perioperative outcome.
The non linear electrical loads can give rise to a number of disturbances in electrical power networks. Among them, the high consumption of relative power is to be noted and so is the several harmonic components which may be injected in the industry system and very often in the utility system. So, by using appropriate technical considerations, as well as measurements in typical special electrical loads, such negative effects are analyzed and ways of minimizing them are suggested. (author) 3 refs., 11 figs., 6 tabs.
The Fast Flux Test Facility has provided a very useful framework for testing the advances in Liquid Metal Reactor Safety Technology. During the licensing phase, the switch from a nonmechanistic bounding technique to the mechanistic approach was developed and implemented. During the operational phase, the consideration of new tests and core configurations led to use of the anticipated-transients-without-scram approach for beyond design basis events and the move towards passive safety. The future role of the Fast Flux Test Facility may involve additional passive safety and waste transmutation tests. 26 refs.
This report gives the results of an assessment of the effects on seabirds of possible petroleum exploration at the shelf outside Central-Norway out to 1"o East. By combining oil spill simulations with the valued ecosystem components, i.e. seabirds, their distribution, and their vulnerability indexes, the relative index values for the direct effects of oil spills were calculated. For the purpose, the analysis system SIMPACT was used. On the basis of these results and other relevant considerations, recommendations for limiting a possible drilling activity are given. 85 refs., 49 figs., 9 tabs.
The steady state ampacity is calculated for mixed electric power underground cable circuits in a single trench or ductbank. The methodology presented in this paper can be applied to any practical number of balanced, three phase circuits (each in trefoil, pipe or conduit) of different voltage classes, cable sizes, load currents and cable systems to located anywhere within a single trench or ductbank. The different thermal resistivities of the backfill or ductbank and the surrounding soil are taken into consideration. A practical example for 10 circuits in a trench is provided.
During one year more than 40,000 items of information on radiation exposure of personnel involved in the handling of radiation sources and more than 5,000,000 items on irradiation of other people are collected in the authors' laboratory. Considerable progress in assessment of mean annual gonad dose of genetically sifnificant dose was attained by means of an algorithm for a personal computer. This simple and inexpensive system has led to a higher accuracy in the application of protective measures. (author).
The work is devoted to the construction of a viable of locally anisotropic, i.e. Finslerian, space-time and to the generalization, on this basis, of the relativistic theory of gravitation. Arguments in favour of this model are considered. From physical considerations the concrete form of the Finslerian metric has been reconstructed and within the framework of the correspondence principle a formalism of the theory has been developed. The approach suggested is aimed at developing unified gauge theories of all fundamental interactions. Much attention is given to the nontrivial physical manifestations of local space anisotropy and to the possibility of its experimental detection. (orig.)
In the geological disposal facility of the high-level radioactive waste, a group of galleries is designed in parallel at the depth of more than 300 m below surface. This is an unprecedented structure in the field of conventional engineering, and it is necessary to take this characteristic into consideration in the design of the galleries. In the geological disposal facility, as well as ensuring the dynamic stability of the gallery during construction and operational periods, it is necessary to evaluate the EDZ adequately for long-term stability after the closure. In this study, analysis of the 'multi tunnels model' which represents the whole gallery group was performed and the results about the outbreak behavior of EDZ were summarized. (author)
An epidemiological study is under way in the Schneeberg/Schlema region where radon concentration in dwellings were found to vary between 10 Bq/m"3 and 10 kBq/m"3. For several reasons, indoor radon levels are expected to have considerably varied over the past decades. To take these potential fluctuations into account, indoor radon concentration measurements should be combined with retrospective measurements. In this way, possible outliners in the epidemiological study could be sorted out. (A.K.)
We describe a scheme for quantum error correction that employs feedback and weak measurement rather than the standard tools of projective measurement and fast controlled unitary gates. The advantage of this scheme over previous protocols (for example Ahn et. al, PRA, 65, 042301 (2001)), is that it requires little side processing while remaining robust to measurement inefficiency, and is therefore considerably more practical. We evaluate the performance of our scheme by simulating the correction of bit-flips. We also consider implementation in a solid-state quantum computation architecture and estimate the maximal error rate which could be corrected with current technology.
Long steam turbine blades are always made as massive blades cut from the solid. For a given blade material and given rotational speed of the steam turbine, the maximum permissible blade length depends on a tapering factor which expresses the ratio of the centrifugal force of the real blade, always twisted and tapered, to the centrifugal force of the theoretical cylindrical blade of the same flow cross-section. This factor can be further reduced to a considerable degree, due to a better approximation to the shape having uniform srength, if the blade is constructed as a hollow blade. (orig./LH).
Environmental considerations have led the Italian electric utility, ENEL, to use an advanced compact design for the reconstruction of a 60kV power line on the outskirts of Rome. This solution has achieved the following aims: minimisation of the visual impact by reducing the size of the supports; reduction of the occupation of the area especially during construction; reduction of damage due to the degree of penetration into the soil. The use of one stem tubular supports and bored pile foundations is described. The scheme has been shown to be viable in terms of planning and low environmental impact and also cost-effective and is likely to be adopted by ENEL in other situations. (UK)
It is shown that the method used for comparing theoretical and experimental results is erroneous and the values of the couple stress parameters obtained for blood flow are incorrect. A method for determining the couple stress parameters is presented. The computational work in the improved method is considerably less. It is observed that both the couple stress parameters are functions of concentration. An empirical relation between concentration and the stress parameters is obtained. The shear viscosity and non-dimensional axial velocity are functions of concentration. Some uses of determining the values of the couple stress parameters are suggested.
There is increasing pressure to operate laboratory facilities in environmentally and financially sustainable ways. A key factor in achieving this goal is careful consideration of how energy is used by the buildings' ventilation system, both for conditioning air supplied to the laboratories and the energy used moving air through the building. Traditionally, laboratory energy use is treated as an engineering concern within the scope of the building's overall design and operation. However, this approach limits the involvement of key stakeholders in many important decisions and can lead to unexpected safety concerns for the laboratory's users. We believe that a broad view of the parties affected by a laboratory building's operations is necessary to avoid having the various stakeholders working...
The Belinskii, Khalatnikov and Lifshitz conjecture \\cite{bkl1} posits that on approach to a space-like singularity in general relativity the dynamics are well approximated by `ignoring spatial derivatives in favor of time derivatives.' In \\cite{ahs1} we examined this idea from within a Hamiltonian framework and provided a new formulation of the conjecture in terms of variables well suited to loop quantum gravity. We now present the details of the analytical part of that investigation. While our motivation came from quantum considerations, thanks to some of its new features, our formulation should be useful also for future analytical and numerical investigations within general relativity.
In the past, Condition Monitoring Systems (CMS) still showed weaknesses during the employment in the damage diagnosis and/or early failure detection of damages of roller bearings in transmissions of wind power plants. This is not only due to the insufficient consideration of the variable frequency of the wind power plants during the internal processing. The presently used methods of analysis result from the communication technology and are used successfully for years at frequency solid systems. Usually, only too few information are at the disposal to the supplier of CMS in order to parametrize their systems on the respective application particularly. An exact knowledge of the internal structure of the object to be diagnosed is compellingly necessary for a successful diagnosis so that a loadable statement based on the acquired measuring data base becomes possible. Furthermore, one must clarify the borders of the presently used systems. The theory of these systems is ...
In order to predict or to evaluate the structural reliability of a variety of nuclear components under actual changing operating conditions, it is necessary to take the detailed geometrical features of components into consideration on one hand, and thermo-mechanical loading conditions with space and time variations during the lifetime, on the other hand. This consideration leads the authors to develop a super large-scale structural analysis program based on a parallel computational FEM with a variable scale of PC cluster architecture, whose prototype system is presented in a companion paper in this Symposium. Development of the PC cluster technology is one of the most important subjects in large-scale structural simulation, reducing computer costs and thus making simulation more acceptable to the engineering community. This paper presents the developmental status of the parallel FEM solver, demonstrating computational capabilities with three ...
In the Joule II project JOU2-CT 94-0428 `Development and Testing of Stand-Alone small-size Solar Photovoltaic-Hydrogen power Systems (SAPHYS)`, different design configurations are compared and discussed. In this paper we present some of the proposed design configurations and discuss their benefits and drawbacks. Simplified expressions for system efficiency for the different configurations are presented. These expressions are based on average efficiencies for the solar cells, the electrolyzer, the batteries, the hydrogen storage and the fuel cells. Mean fractions of energy passing through the energy storages are also assumed. From considerations in the paper one conclusion becomes apparent, i.e. the direct use of the energy should be maximized. Another conclusion is that one of the most important factors in Solar Photovoltaic Hydrogen Power Systems is the solar cell efficiency. This point seems to be lost in typical projects where focus is put on the electrolyzer, ...
Flow-induced vibration is an important concern to the designers of heat exchangers subjected to high flows of gases or liquids. Two-phase cross-flow occurs in industrial heat exchangers, such as nuclear steam generators, condensers, and boilers, etc. Under certain flow regimes and fluid velocities, the fluid forces result in tube vibration and damage due to fretting and fatigue. Prediction of these forces requires an understanding of the flow regimes found in heat exchanger tube bundles. Excessive vibrations under normal operating conditions can lead to tube failure. Relatively little information exists on two-phase vibration. This is not surprising as single-phase flow induced vibration; a simpler topic is not yet fully understood. Vibration in two-phase is much more complex because it depends upon two-phase flow regime, i.e. characteristics of two-phase mixture and involves an important consideration, which is the void fraction. The effect of characteristics of ...
The inner part of a fusion reactor will have to operate at very high neutron loads. In steady-state reactors the minimum fluence before the scheduled replacement of the reactor core should be at least l0-15 Mw.yr/m2. A more frequent replacement of the core is hardly compatible with economic constraints. A most recent summary of the discussions of these issues is presented in Ref. [l]. If and when times come to build a commercial fusion reactor, the availability of information on the behavior of materials and components at such fluences will become mandatory for making a final decision. This makes it necessary an early development and construction of a neutron source for fusion material and component testing. In this paper, we present information on one very attractive concept of such a source: a source based on a so called Gas Dynamic Trap. This neutron source was proposed in the mid 1980s (Ref. [2]; see also a survey [3] with discussion of the early stage of the ...
Enzyme-linked Immunosorbent assay systems for the identification of irradiated egg, pork and chicken was developed. Eggs were irradiated in their shells to 0.5{approx}7kGy. Pork was irradiated to 0.5{approx}3kGy and chicken irradiated to 0.5kGy{approx}5kGy. The most sensitive proteins to irradiation were screened by SDS-PAGE and purified. Ovalbumin from egg, salt soluble protein(p) from pork, and salt soluble protein(c) from chicken showed the most sensitivity to irradiation. To investigate for a practical use in identifying of irradiated egg, pork and chicken, competitive ELISA was performed. The binding activity of ovalbumin to anti-ovalbumin IgG was reduced in a dose-dependent manner by irradiating up to 7kGy, and considerably lowered after irradiating at 7kGy. The concentration of 50% inhibition of ovalbumin to IgG was increased to 1.5(0.5kGy){approx}3.7(7kGy) times in an dose-dependent relationship. The binding activity of salt soluble protein(p) to anti-salt ...
ObjectivesThe objective of this meeting will be to interface the two ends of the particulate flow spectrum - those working to understand the fundamentals of granular flows and those attempting to control particulate flows in an industrial setting - to develop solutions to the complex problems presented by dense granular flows. We will aim~%~~%~to provide a forum for the interface between practical users of particulate technology and the developers of theories for understanding granular flow;~%~to present [continued...]DescriptionIn practical situations such as those met in industry where segregation and mixing are important, understanding particulate flows is complex due to the presence of polydispersity, anisotropy and complex grain morphology. In attempting to model such systems, many of these features are generally ignored, except perhaps through empirical parameter fitting. Developing a theory to include these effects is a considerable ...
Attention-deficit/hyperactivity disorder (ADHD) is a prevalent neurobehavioral disorder affecting 5% to 10% of children. Although considered to be a highly familial disorder, ADHD heritability estimates of 60% to 80% highlight the considerable role that environmental factors may still play in disorder susceptibility. Proposed ADHD environmental risk factors include prenatal substance exposures, heavy metal and chemical exposures, nutritional factors, and lifestyle/psychosocial factors. This paper reviews the literature published in 2010 investigating the association between environmental risk factors and ADHD or related symptomatology. Sources of risk factor exposure and the proposed mechanism by which each exposure is linked to ADHD-related neurobehavioral changes are also reported. Metho...
Volume V of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the transport parameter and source term data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Volume III of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the data covering groundwater recharge and discharge. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.
Power Fluidic systems for the control of liquids and gaseous flows have been adopted for use in radioactive processing plants in the UK. These devices are intrinsically reliable with no mechanical moving parts because they are able to make use of the hydrodynamics of the fluids being controlled. This reliability feature leads to a zero cell maintenance concept and the elimination of mechanical drive/control systems in cell. The first phase of the development work led to their use in the Fast Reactor Reprocessing Plant at Dounreay and the Highly Active Liquor Storage facility at Sellafield. The success of these early developments has led to an extensive development programme for an extended range of applications in the Thermal Oxide Reprocessing Plant and its associated waste treatment facilities at Sellafield. The technology has now been fully demonstrated and adopted for these plants with considerable benefit over a wide range of applications.
The difficult economic circumstances with which almost the whole world had to contend, brought serious financial crisis in many countries. South Africa also had its own share of serious problems. Despite this situation, Transvaal Consolidated Land and Exploration Company, Limited, showed on increase in earnings of 24 per cent per share. The reason for this lies mainly in two areas. Firstly the company acquired the mining related business of Rand Mines, Limited. Included in the acquisition was a partfolio of shares mainly in the company's associated gold and uranium mining companies and additional shares in its listed coal mining subsidiaries. Secondly, the average gold price realised by producers in rand terms, was considerably higher than in the previous year. Consolidated profit attributable to members increased by 52 per cent to R82,6 million.
In this study, wood samples were exposed to light irradiations (direct sunlight, xenon lamp, mercury vapour lamp) and thermal treatments were carried out in dry- and in humid conditions at 90degreeC. One part of the samples was covered by an aluminium plate during light irradiation. The samples under the aluminium plate also suffered considerable chemical changes, monitored by infrared technique and colour measurement. The sunlight produced greater colour change under the aluminium plate than the artificial light sources. During light irradiation, the carbonyl band having two maximum at 1700 and 1746cm-1 increased and the peak of the aromatic skeletal vibration arising from lignin (1510cm-1) decreased together with the guaiacyl vibrations at 1275cm-1. There was absorption decrease at 1174c...
The advent, in the near future, of compact X-ray sources like Thomson Back-Scattering (TBS) will allow the clinical application of advanced X-ray imaging techniques, such as phase contrast, with higher sensitivity and lower impact in terms of dose delivery. In this work, we theoretically investigated the possibility of using such sources for phase contrast imaging of micro-calcifications included in a breast tissue. In our study we analyzed the phase and amplitude distribution of the TBS source and we showed that this source can be used for phase contrast imaging since the source coherence at the sample position is sufficiently high for achieving good contrast and micrometer spatial resolution. Indeed the spatial coherence of a TBS source is closer to that of a synchrotron radiation source, and much better than that of a laboratory source. Moreover, we showed the advantages of phase imaging with respect to standard absorption imaging, in the specific case of micro-calcifications ...
The process of radiation induced electron capture by protons or deuterons producing new ultra low momentum neutrons and neutrinos may be theoretically described within the standard field theoretical model of electroweak interactions. For protons or deuterons in the neighborhoods of surfaces of condensed matter metallic hydride cathodes, such conversions are determined in part by the collective plasma modes of the participating charged particles, e.g. electrons and protons. The radiation energy required for such low energy nuclear reactions may be supplied by the applied voltage required to push a strong charged current across a metallic hydride surface employed as a cathode within a chemical cell. The electroweak rates of the resulting ultra low momentum neutron production are computed from these considerations.
The paper analyses the advantages and disadvantages of the second generation improved technologies and third generation technologies mainly developed in China in terms of safety and economy. The paper also discusses the maturity of the second generation improved technologies and the sophistication of the third generation technologies respectively. Meanwhile, the paper proposes that the advantage and disadvantage of second generation improved technologies and third generation technologies should be carefully taken into consideration and the relationship between the maturity and sophistication should be properly dealt with in the current stage. A two-step strategy shall be taken as a solution to solve the problem of insufficient capacity of nuclear power, trace and develop the third generation technologies, so as to ensure the sound and fast development of nuclear power. (authors)
The uncertainty of the elemental analysis is one of the major factors governing the utility of on-line Prompt Gamma Neutron Activation Analysis (PGNAA) in the blending and sorting of bulk materials. In this paper, a general method applicable to Gamma spectra processing is presented and applied to PGNAA in mineral industry. Based on the Fourier transform of spectra and their de-correlation in the Fourier space (the improvement of the conditioning of the correlation matrix), processing of overlapping of characteristic peaks minimizes the propagation of random errors, which optimizes the accuracy and decreases the detection limits of elemental analyses. In comparison with classical methods based on the linear combinations of relevant regions of spectra the improvement may be considerable, especially when several elements are interfering. The method is applied to four case stories covering both borehole logging and on-line analysis on conveyor belt of raw materials.
A new process for the removal of tar from biosyngas, OLGA (Oil and Gas Washer), is presented. This gas cleaning technology is based on physical principles and is designed to eliminate tar problems that relate to fouling and er pollution. The applied principles are confirmed by experimental validation. OLGA can be operated without suffering from harmful effects on important gasification characteristics as cold gas efficiency, gasifier simplicity, and feedstock flexibility. Some fundamental considerations in the development of OLGA are discussed. Amongst these is a different approach to the tar problem. This approach does not consider the total tar content as decisive in the evaluation of gas cleaning equipment. Instead, evaluation is focussed on whether tar properties as condensation behaviour and water solubility can still occur. A biosyngas free of tar should therefore be synonymous to a biosyngas that is free of tar related problems.
Aquatic sediments feature a two-way interaction between contaminants and benthic macrofauna. The effect of the macrofauna community on the transport of contaminants in sediment has received considerable attention. Yet, few studies have investigated the reverse effect, i.e., the influence of contaminants on bioturbation activity. To this end, we performed laboratory experiments to investigate the effect of copper contamination on sediment reworking activity of the ragworm Nereis diversicolor. A density of 570 ind m2 was introduced in mesocosms containing natural and copper spiked (2.99 nmol Cu g?1) cohesive intertidal sediments from Ponta da Erva (Tejo estuary, Portugal). Luminophore tracers were used to quantify sediment reworking activity over time (2, 7, 14 and 21 days). Bioturbation was...
There is now a scientific consensus that current rates of accumulation of greenhouses gases in the atmosphere will result in significant global warming and climate change. These changes are likely to have important impacts on a wide range of human activities and the natural environment. There has now been a considerable weight of literature published on the impacts of global warming, much of it very recent. This report seeks to summarise the important results, to analyse the uncertainties and to make a preliminary analysis of the feasibility of monetarising these environmental costs. The impacts of global warming are divided into ten major categories: agriculture, forests and forestry, terrestrial ecosystems and biodiversity, hydrology and water resources, sea level rise and coastal zones, energy, infrastructure/transport/industry, human health and air quality, oceans, and cryospheric impacts. The results of major summary reports are analysed, notably the report of ...
We study the finite temperature electroweak transition with non-perturbative lattice Monte Carlo simulations. We find that it is of first order, at least for Higgs masses up to 80 GeV. The critical temperature of the phase transition is found to be smaller than that determined by a 2-loop renormalization group improved effective potential. The jump of the order parameter at the critical temperature is considerably larger than the perturbative value. By comparing lattice data and perturbation theory, we demonstrate that the latter, for the computation of the vacuum expectation value of the Higgs field v(T) in the broken phase at given temperature, converges quite well, provided v(T)/T>1. An upper bound on the Higgs mass necessary for electroweak baryogenesis in the light of the lattice data is briefly discussed.
Different cooling speeds after previous solution annealing at 1130deg C for 0.5 hour were simulated in laboratory experiments. The following conditions were examined: (1) Direct water quenching, (2) cooling in air for 0.5 min to 950deg C/water quenching, (3) cooling in air for 1.5 min to 750deg C/water quenching, (4) cooling in furnace for 5 min to 750deg C/water quenching. The results of the investigations have shown that a variation of the cooling conditions causes considerable changes in the creep behaviour. (orig.).
Theory of quantum games is relatively new to the literature and its applications to various areas of research are being explored. It is a novel interpretation of strategies and decisions in quantum domain. In the earlier work on quantum games considerable attention was given to the resolution of dilemmas present in corresponding classical games. Two separate quantum schemes were presented by Eisert et al. and Marinatto and Weber to resolve dilemmas in Prisoners' Dilemma and Battle of Sexes games respectively. However for the latter scheme it was argued that dilemma was not resolved. We have modified the quantization scheme of Marinatto and Weber to resolve the dilemma. We have developed a generalized quantization scheme for two person non-zero sum games which reduces to the existing schemes under certain conditions. Applications of this generalized quantization scheme to quantum information theory are studied. Measurement being ubiquitous in quantum mechanics can ...
The operation of the Bullhouse Minewater System, used to treat iron-rich minewaters discharged from long-abandoned coal mines, was studied to minimise pollution of the Upper Don river in the UK. Tests were carried out to determine optimal operating conditions. Ochre flocculation with polyacrylamide was efficient in batch tests as the ochre self-flocculated and sedimented in the lagoon without the need for chemical enhancement. The rate of accretion of the pipework in the system was modified by partial dewatering, reshaping and hardening of the deposits during ageing. Samples of ochre recovered from the drying beds and sump deposits were converted to ferric sulphate coagulant by dissolution with sulphuric acid and used with a polyelectrolyte to successfully purify reservoir water and pretreat wastewater. There was considerable local interest in the scheme with educational opportunities for schools and colleges.
In recent years sufficient new spectra of actinides in their numerous valence states have been measured to encourage a broader scale analysis effort than was attempted in the past. Theoretical modelling in terms of effective operators has also undergone development. Well established electronic structure parameters for the trivalent actinides are being used as a basis for estimating parameters in other valence states and relationships to atomic spectra are being extended. Recent contributions to our understanding of the spectra of 4+ actinides have been particularly revealing and supportive of a developing general effort to progress beyond a preoccupation with modelling structure to consideration of the much broader area of structure-bonding relationships. We summarize here both the developments in modelling electronic structure and the interpretation of apparent trends in bonding. 60 refs., 9 figs., 1 tab.
In recent years sufficient new spectra of actinides in their numerous valence states have been measured to encourage a broader scale analysis effort than was attempted in the past. Theoretical modelling in terms of effective operators has also undergone development. Well established electronic structure parameters for the trivalent actinides are being used as a basis for estimating parameters in other valence states and relationships to atomic spectra are being extended. Recent contributions to our understanding of the spectra of 4+ actinides have been particularly revealing and supportive of a developing general effort to progress beyond a preoccupation with modelling structure to consideration of the much broader area of structure-bonding relationships. We summarize here both the developments in modelling electronic structure and the interpretation of apparent trends in bonding. 60 refs., 9 figs., 1 tab.
Inhibition of adipogenesis and lipid accumulation has a very crucial role to prevent obesity. Low molecular weight (LMW) chitosan is known to inhibit fat accumulation and adipogenesis. (N,O)-sulfated chitosan is a sulfation derivative of chitosan oligomers, and its anti-obesity effect is not yet reported. In this study, it has been reported that (N,O)-sulfated chitosan significantly decreased lipid accumulation, an indicator for adipogenesis, in differentiating 3T3-L1 preadipocyte cells. Furthermore, mRNA expressions and protein levels of key adipogenic markers such as peroxisome prolifetor-activated receptor (PPAR)-@c and CCAAT-enhancer binding protein (C/EBP)-@a were considerably decreased by (N,O)-sulfated chitosan treatment. As a consequence, sulfation of LMWC remarkably increased its ...
We study spontaneously generated entanglement (SGE) between two identical multilevel atoms in free space via vacuum-induced radiative coupling. We show that the SGE in two-atom systems may initially increase with time but eventually vanishes in the time scale determined by the excited state lifetime and radiative coupling strength between the two atoms. We demonstrate that a steady-state SGE can be established by incoherently pumping the excited states of the two-atom system. We have shown that an appropriate rate of incoherent pump can help producing optimal SGE. The multilevel systems offer us more chanel to establish entanglement. The system under consideration could be realized in a tight trap or atoms/ions doped in a solid substrate.
In this systematic examination of some of the spectroscopic properties of the f-elements we deal with both the trivalent lanthanides and actinides. We summarize the present status of our energy level calculations in single crystal matrices and in aqueous solution, and compare the predicted crystal-field structure in certain low-symmetry sites with that observed. Some interesting new structural insights are thereby gained. The state eigenvectors from these calculations are then used in part in reassessing and interpreting the intensities of transitions in aqueous solution via the Judd-Ofelt theory. The parameters of this theory derived from fitting experimental data are compared with those computed from model considerations. Finally, we discuss some recent contributions to the interpretation of excited state relaxation processes in aqueous solution. 79 references, 23 figures, 17 tables.
In this paper we provide a geochemical investigation on 34 groundwater samples in the Mt. Vulture volcanic aquifer representing one of the most important groundwater resources of the southern Italy pumped for drinking and irrigation supply. The present study includes the first data on the abundance and mobility of minor and trace elements and the thermodynamic considerations on water-rock interaction processes in order to evaluate the conditions of alkali basalt weathering by waters enriched in magma-derived CO2. The results highlight the occurrence of two hydrofacies: bicarbonate alkaline-earth and alkaline waters deriving from low-temperature leaching of volcanic rocks of Mt. Vulture, and bicarbonate-sulfate-alkaline waters (high-salinity waters) related to prolonged water circulation in...
Bisaminoethanethiol (BAT) ligands with various gem-dimethyl and amide groups were prepared, and the corresponding neutral Tc-99m complexes were prepared and evaluated for their relative stabilities by ligand-exchange reactions. It was demonstrated that technetium complexes containing gem-dimethyl substituents have higher lipophilicities, whereas those with an amide group possess greater stability, which enhances ligand-exchange reaction. The most interesting observation was that the brain uptake in rats is not determined only by lipophilicity. Apparently, Tc-99m complexes with an amide functional group display lower brain uptakes in rats compared to those without an amide group. The brain uptake was strongly influenced by substituents on the BAT ligand. These factors are critically important and should be taken into consideration when designing Tc-99m-labeled agents for CNS receptor imaging.
This paper consists the radiation streaming analysis of Horizontal Flux Unit (HFU) penetrations in Calandria Vault of 540 MWe PHWR. There are total 7 HFU penetrations on west wall of calandria vault. As these penetrations are in accessible area, a detailed analysis has been carried out to find the neutron and gamma dose rates around these penetrations when reactor is operating. Analysis has been carried out Using the computer code MCNP and DOT-III. Based on the predictions at HFU penetrations, shielding arrangement was recommended. Neutron and gamma dose rate higher than estimated were observed at TAPS-4. This was because of installed shield not being similar to recommended one due to site conditions. Subsequently semi-empirical calculations using measured data were carried out by MCNP to further augment the existing shield taking into consideration the space limitations at site. (author)
We study some aspects of the experimental behaviour of tachyons, in particular by finding out their <> shape. A Superluminal particle, which in its own rest frame is spherical or ellipsoidal (and with an infinite lifetime), would <> to a laboratory frame as occupying the whole region of space bound by a double cone and a two sheeted hyperboloid. Such a structure (the tachyon <>) rigidly travels with the speed of the tachyon. However, if the Superluminal particle has a finite lifetime in its rest frame, then in the laboratory frame it gets a finite space extension. As a by-product, we are able to interpret physically the imaginary units entering - as is well known - the transverse co-ordinates in the Superluminal Lorentz transformations. The various particular or limiting cases of the tachyon shape are thoroughly considered. Finally, some brief considerations concerning possible experiments to look for ...
Active Process Water (APW) System, provided as unitized closed loop system in Tarapur Atomic Power Project Units-3 and 4, serves to remove heat from various heat exchangers. One of the important loads served by APW system is shutdown cooling heat exchangers and if APW shutdown is taken then reactor cannot be maintained in cold shutdown condition. It is estimated that after 7 days of reactor shutdown, if about 20% of the normal cooling flow to shutdown cooling heat exchangers is provided then along with keeping PHT in cold shutdown state, reactor components, moderator, end shield water, calandria vault water and calandria vault concrete temperature can be maintained within technical specification limits for extended duration. (author)
The effect of counter-ion species on the local conformation of fully-charged poly(L-glutamate) in added-salt aqueous solutions were studied by small-angle X-ray scattering(SAXS). In the case of presence of monovalent counter-ion, the scattering behaviour could be explained by taking into consideration the excluded volume effect and intermolecular-interface interaction on the scattering function of wormlike chain. On the other hand, since SAXS profile of the solution in the presence of divalent counter-ion well fitted to the scattering function of dendrimer, it suggested that the conformation of polymer chain in such solution would be more compact conformation than that of presence of monovalent ion.
Integrative and firing properties are important characteristics of neuronal circuits and these responses are determined in large part by the repertoire of ion channels they express, which can vary considerably between cell types. Recently, a new mode of operation of voltage dependent sodium channels has been described that generates a so-called resurgent Na^+ current. Accumulating evidence suggests resurgent Na current participates in the generation of sub-threshold inward Na^+ current causing membrane depolarization which provides the necessary drive to fire high-frequency action potentials. Recent studies indicate that resurgent Na^+ current could be a more widespread feature than previously thought.
In the past decade, considerable progress has been made on reducing the seismic response of structures through seismic isolation. Application of seismic-isolation techniques to nuclear power facilities is currently being investigated. This paper presents an analysis of the effect of long period motions on a seismic-isolated nuclear structure. Preliminary analysis indicates that long-period earthquake motions increase structural accelerations and relative displacements between the upper and lower mats. Relative displacement between the mats can be represented by spectral displacement at the frequency of the structure, and can be effectively reduced by increasing viscous damping in the isolator. The isolated structure behaves as a system with one degree of freedom. Future analysis of seismic effects on seismic-isolated structures should include the linear and nonlinear effects of soil-structure interactions. 3 refs., 12 figs., 3 tabs.
The IAEA Assessment of Safety Significant Events Team (ASSET) report presents the results of an ASSET team's assessment of their investigation of the effectiveness of the plant for prevention of incidents since 1990 at Zaporozhe nuclear power plant. The results, conclusions and suggestions presented herein reflect the views of the ASSET experts. They are provided for consideration by the responsible authorities in Ukraine. The ASSET team's views presented in this report are based on visits to the plant, on review of documentation made available by the operating organization and on discussions with utility personnel. The report is intended to enhance operational safety at Zaporozhe by proposing improvements to the policy for the prevention of incidents at the plant. The report includes, as a usual practice, the official response of the operating organization as well as of the regulatory body to the ASSET recommendations. Figs.
During the last two years, the performance of the Penning trap mass spectrometer ISOLTRAP at ISOLDE/CERN (Geneva) has been considerably enhanced. Many technical improvements have been completed (i) to access nuclides that are produced in minute quantities of only 100 ions s/sup -1/, (ii) to increase the relative mass accuracy to
A general analytical form of the round trip phase shift in grating feedback diode lasers is proposed. Using the new form, it is obvious that the round trip phase shift can be independent of rotation angle in first order approximation when only one restriction condition is met. We call this the quasi synchronous tuning (QST) condition. In the QST region, a considerably large mode hopping free tuning range can be obtained. An adjustment structure with only one freedom is needed to accurately find and locate the quasi synchronous pivot, which is not strictly confined on the grating surface and its extension. It means that the external cavity diode lasers design can be easier and the laser can be more stable and reliable. PMID:21946988
Our study evaluates the impact of forecast errors on organizational cost by simulating a labor-intensive warehouse environment using realistic cost data from a case study. Unlike past studies that measure forecast error in terms of forecast standard deviation, our study also considers the impact of forecast bias, and the complex interaction between these variables. Two cases of organizational cost curves are considered, with differing and asymmetric structures. Results find forecast bias to have a considerably greater impact on organizational cost than forecast standard deviation. Particularly damaging is a high bias in the presence of high forecast standard deviation. Although biasing the forecast in the least costly direction is shown to yield lower costs, sensitivity analysis shows that...
This article argues that anti-corruption agencies at the local-level have been successful in a way that can be evaluated and emulated. A related contention is that corruption control is most effective when the central public integrity agency is part of both a local anticorruption network and a local public management network. Quite reasonably, the international anti-corruption project has focused most time and energy on advocating and assessing efforts made to ensure public integrity at the national level. Baseline studies by scholars and supra-national integrity nongovernmental organizations (NGOs) identify the form of corruption control (if any) adopted by the central government. Key considerations in assessing the status of national anti-corruption agencies (ACAs) are the ones mentioned...
The invention refers a procedure of radiation dose control in irradiated tissues during electron-beam therapy. It aims at meeting the planned radiation dose for diseased tissues and taking care of the healthy ones. Therefore, the dose distribution required is determined before irradiation in consideration of such factors as energy-dependence of detector sensitivity, self-absorption within the tissue, and relative biological effectiveness. Furthermore, the expected intensity distribution of secondary quantum radiation excited in the irradiated tissue is calculated. A radiation detector for local resolution is used for registration. During irradiation the calculated intensity distribution is compared with the measured one. The invention is applicable in radiation therapy with monoenergetic electron beams.
Monte Carlo calculations of proton irradiation of permanent magnets for the TRADE experiment have been performed. An irradiation dose of about 4´106 Gy/yr/mA has been estimated due to beam losses in normal operating conditions. Existing experimental results indicate that this irradiation level may induce a considerable demagnetization: in fact, a dose of 6´107 Gy induces a remanence loss of 0.3 % on samples of Sm2Co17 magnets, which are the most resistant type. More detailed calculations with the final design of the magnets and of the beam line are suggested, to determine if the irradiation levels allowed a reliable operation of the permanent magnets for the entire duration of the TRADE experiment. Damage and gas production rates have also been calculated; the values obtained are very low, thus confirming that the demagnetization process is in great part reversible.
Drug particle size distribution has a profound impact to the content uniformity in low-dose solid drug products. We derived theoretically the skewness of potency distribution as a function of particle size distribution and target dose. It was demonstrated that both skewness and coefficient of variation diverge simultaneously with inverse square root of the target dose. This scaling relation was observed in recent experiment and was verified by Monte Carlo (MC) simulation, which was employed for the first time to solve for the full potency distribution from a random retrieving model. When tested against the criteria from USP uniformity of dosage units, MC simulation showed a striking anisotropic distribution of the data. This suggests a full-scale consideration of the potency distribu...
The Advanced MAPLE is a research reactor design under development as a high-flux neutron source. The main performance goals for the reactor are a high peak thermal neutron flux in a heavy-water reflector tank, and a high average fast neutron flux in a central irradiation facility, with a maximum linear fuel rod rating of less than 120 kW/m. This study investigated the neutronic and reactor design consequences of the use of H_2O coolant as opposed to D_2O. The neutronics results, and several other considerations, indicate that H_2O coolant has a number of advantages. It is suggested that the H_2O coolant option be considered in the design of the Advanced MAPLE reactor. (L.L.) 9 refs., 4 figs., tab.
Abstract Evaluation of pharmaceutical agents in children is now conducted earlier in the drug development process. An important consideration for this pediatric use is how to assess and support its safety. This article is a collaborative effort of industry toxicologists to review strategies, challenges, and current practice regarding preclinical safety evaluations supporting pediatric drug development with biopharmaceuticals. Biopharmaceuticals include a diverse group of molecular, cell-based or gene therapeutics derived from biological sources or complex biotechnological processes. The principles of preclinical support of pediatric drug development for biopharmaceuticals are similar to those for small molecule pharmaceuticals and in general follow the same regulatory guidances outlined by...
This book applies the Los Alamos Solar Load Ratio (SLR) method to the design of passive solar heating systems, with an emphasis on the average annual heating energy consumption. Recommendations are given on minimizing heating energy consumption by appropriate choices of conservation level and solar system parameters. Analytical methods and supporting tables are presented which enable simple, fast estimates of the heating energy consumption as part of the design process. Topics considered include SLR correlations, the load collector ratio (LCR) method, sensitivity data, cooling considerations, conservation formulas, design procedure, life-cycle costs, high-mass direct gain buildings, low-mass sun-tempered buildings, sunspaces, off-reference night insulation, correlation equations, and mixed systems.
The PARLOC Pipeline and Incident Databases provide the most complete information available on North Sea pipelines and risers from 1975. The database information enables the frequency of incidents which either result, or have a potential to result, in loss of containment to be related to the pipeline population as a whole or expressed as a function of particular pipeline characteristics. The importance of the PARLOC study in risk assessments of offshore pipelines is acknowledged worldwide and it is recognized as having contributed positively to their safer operation. Continuing improvements ensure that it remains a key reference in risk assessment studies. This paper describes the improvements which are being made to the study and shows how PARLOC is being used by the offshore industry in the consideration of pipeline safety. The rationalization of current arrangements for regulating pipeline safety presented in the new UK Pipeline Safety Regulations offer an ...
An evolutionary model of dynamical processes in protostellar disks is described and illustrated with graphs of typical results. The effective transport mechanisms are discussed, including thermal convection, nonaxisymmetric gravitational instabilities in the outer regions of disks, and wave propagation. Consideration is then given to the stages of dynamical evolution, FU Ori outburst phenomena, unsteady accretion-disk flows, and nonlinear feedback as a mechanism to modulate mass transfer. The simulations show that mass redistribution is determined by angular-momentum transfer, which in turn is regulated by the effective viscosity generated by convectively driven turbulence. Significant mass transfer occurs as a result of mixing of infalling material with disk gas and is affected by the tidal torque associated with the growth of nonaxisymmetric disturbances in the outer disk. The time scale for disk evolution is found to be about 1 Myr. 72 refs.
The evaluation of calculated values determined by means of the equations given in the TRD 300/301 standard resulted in two nomographs by which it is possible to find the theoretical wall thickness of cylinder shells without cutouts and branches as well as cylinder shells with an inclined or vertical single branch without additional thickening. The equations for the calculation of cylinder shells with an inclined single branch according to TRD 301 having only an iterative solution, the nomographs will be a considerable help for the engineering work. The determination of the theoretical wall-thickness from the nomographs is demonstrated by means of examples.
This essay aims to summarize the main physical features arising from a new supersymmetric theory of gravitation. Based on preliminary discussions about classical field theory, cosmology, algebra and group theory, and taking formal results and theoretical considerations in comparison with several contributions from great authors, present work deals with gravity inside the limits of a meta-field theory, that is, a non-quantized but consistent representation of supergravity, the supersymmetry between gravitons and gravitinos. The introduction of meta-fields furnishes an independent framework for the study of gravity despite of constraints of quantization, treating the supersymmetric partners as deterministic actors of gravitation and not simply probabilistic entities. I explain my belief that gravitational field, by its own nature, is not quantizable in the same foot as the other fields, what does not means that we can not understand gravity by similar formal veins. ...
A complex modulated structure is described for reactive elements that have the capability of considerably more heat than organic explosives while generating a working fluid or gas. The explosive and method of fabricating same involves a plurality of very thin, stacked, multilayer structures, each composed of reactive components, such as aluminum, separated from a less reactive element, such as copper oxide, by a separator material, such as carbon. The separator material not only separates the reactive materials, but it reacts therewith when detonated to generate higher temperatures. The various layers of material, thickness of 10 to 10,000 angstroms, can be deposited by magnetron sputter deposition. The explosive detonates and combusts a high velocity generating a gas, such as CO, and high temperatures. 2 figs.
ObjectivesTo determine the reaction rate of slag during curing and factors affecting reactivity.~%~~%~To measure the rates of chloride ingress into concrete and the extent of chloride binding.~%~~%~To determine conditions for pitting corrosion and the nature of corrosion products.~%~~%~To characterise the reactions in slag-calcium alumina cement hydration and the nature of the products.~%~DescriptionBlast-furnace slag has latent hydraulic properties, giving considerable potential for commercial use in addition to its widespread use as a partial replacement for Portland cement, notably in alkali-activated slag (AAS) and slag-calcium alumina cement (CAC) concretes. Use of AAS concretes is already well-established in China and the former USSR, but their further application is hindered by lack of research into setting, hydration and durability, Slag/CAC blends are new materials whose chemistr [continued...
The Real-Time Specification for Java (RTSJ) is silent on multiprocessor issues. It attempts not to preclude multiprocessor implementations but provides no direct support. Many areas of the RTSJ leave an implementation considerable freedom on how it provides the defined functionality. One such area is the asynchronous event handling (AEH) model. Events are fired and associated handlers are scheduled for execution in response; handlers have defined scheduling parameters and deadlines. The primary goal of the AEH model is to support a lightweight real-time concurrency model. Hence handlers, in general, do not have dedicated threads. Rather, the implementation is responsible for ensuring that all handlers meet their deadlines. Typically real-time threads are assigned to execute handlers by the...
Over the decades, basic research in life sciences has profited greatly from the study of the small unicellular fungal species Saccharomyces cerevisiae. This yeast turned out to be key for the identification and understanding of molecular mechanisms that underlay the basic functions of all eukaryotic cells. These include, but are not limited to, the regulatory mechanisms behind cellular reproduction (cell cycle control), cellular morphogenesis (cell polarity, cytoskeleton and membrane trafficking) and the management of cellular information (chromosome biology, transcription and translation). Rapid access to genomic information of many yeast species, combined with bioinformatics analyses, provide information on the evolutionary history of yeasts and the molecular ancestry of their constituen...
In this work, we report for the first time on the analysis of genetic diversity within a set of 36 Tunisian Opuntia ficus indica (L.) Mill. ecotypes using RAPD markers.Random decamer primers were screened to assess their ability to detect polymorphisms in this plant crop. Thirty-nine RAPD markers were revealed and used to survey the genetic diversity at the DNA level and to establish relationships.Consequently, considerable genetic diversity was detected and the UPGMA analysis permitted the discrimination of all the genotypes and enabled their sorting into thirteen groups. The accession `R Sbiba inerme' was significantly divergent from all tested genotypes. In addition, as shown by the clustering the tested genotypes did not significantly diverge, though originating from different localiti...
Lean premixed combustion (LPC) of natural gas is of considerable interest in land-based gas turbines for power generation. However, modeling such combustors and adequately addressing the concerns of LPC, which include emissions of nitrogen oxides, carbon monoxide and unburned hydrocarbons, remains a significant challenge. In this paper, characteristics of published simulations of gas turbine combustion are summarised and methods of modeling turbulent combustion are reviewed. The velocity-composition PDF method is selected for implementation in a new comprehensive model that uses an unstructured-grid flow solver. Reduced mechanisms for methane combustion are evaluated in a partially stirred reactor model. Comprehensive model predictions of swirl-stabilised LPC of natural gas are compared with detailed measurements obtained in a laboratory-scale combustor. The model is also applied to industrial combustor geometries. (Author)
Microcrystalline-Si thin-film transistors (?C-Si TFTs) formed by using the source/drain contact electrode of self-aligned palladium silicide have been investigated. Both the self-aligned palladium silicided scheme and the previous top-gate staggered structure employ two-mask process steps for fabricating ?C-Si TFTs. However, the self-aligned palladium silicided scheme would cause better device characteristics than the top-gate staggered structure, primarily due to more carrier tunneling. For a gate length of 2 ?m, as compared to the top-gate staggered scheme, this silicided scheme can result in a 40% improvement of on-state current. In addition, as the gate length is reduced to 1 ?m, considerable short-channel effect is caused for both the device schemes.
Various control procedures have been suggested for reducing foodborne infectious diseases. Receiving considerable attention is irradiation. This report estimates the medical and wage (or productivity) benefits associated with prevention of five human diseases transmitted by beef, pork, and chicken. (These diseases can also be transmitted by other vectors, such as eggs, milk, and pets. But these sources are not included in the analysis.) All of these foodborne infectious diseases - salmonellosis, campylobacteriosis, trichinosis, tapeworm, and toxoplasmosis - could be significantly reduced by irradiating meat and poultry. The Food and Drug Administration (FDA) has just approved irradiation of pork to prevent trichinosis (50FR 29658-59) and is considering approval of irradiation of chicken to kill Salmonella. 22 references.
Wave energy device teams have identified three varieties of air turbine as potentially applicable to wave energy devices. These are: conventional axial turbines; Wells, or self-rectifying, axial turbines and Francis turbines. This report examines the constructional requirements of these devices with regard to mechanical, environmental and manufacturing considerations. It is concluded that the major benefit of optimum material selection will be reduced manufacturing costs rather than enhanced turbine performance. A methodology of material selection has been established and candidate materials have been listed for the major components of each turbine type. Comparative costs for alternative materials are included, from which significant, potential economies have been identified. Recommendations are made aimed at achieving optimum material usage in the proposed turbines.
The Jewish philosopher and educator Martin Buber (1878-1965) is considered one of the twentieth century's greatest contributors to the philosophy of religion and is also recognized as the pre-eminent scholar of Hasidism. He has also attracted considerable attention as a philosopher of education. However, most commentaries on this aspect of his work have focussed on the implications of his philosophy for formal education and for the education of the child. Given that much of Buber's philosophy is based on dialogue, on community and on mutuality, it is puzzling that relatively little has been written on the implications of Buber's thought for the theory and practice of non-formal adult education. The article provides a discussion of the philosophy underpinning this aspect of Martin Buber's l...
Mine rescue teams frequently must fight fires and guard against the propagation of fires or explosions during a rescue and recovery operation. The team's ability to fight fires depends a great deal on hands-on experience with different fire fighting agents and equipment. The team's work includes an assessment of fire conditions, mine fire gases and other potential hazards associated with fire fighting activity. This training module covers the underlying principles of the fire triangle and the different methods for controlling, containing and extinguishing fires in a mine. The manual also covers fire-fighting equipment, considerations involved in a sealing operation and the cause-effect of explosions.
The initial growth process and surface structure of thin Pd(silicide) films on clean Si(111)-7x7 surfaces have been studied by low energy ion scattering (ISS) and LEED-Auger techniques. Considerable reaction between Pd and Si at room temperature is observed to extend up to 25 ML thickness of deposited Pd. Heat treatment of the room temperature film produced epitaxial silicide Pd/sub 2/Si(0001) films covered with the accumulated elementary Si layers of 1-2 ML thickness. Deposition of 1/3 ML Pd onto a heated substrate gives a Pd-embedded ordered surface of Si(111)-..sqrt..3x..sqrt..3R30/sup 0/, the feature being similar to the cases of Ag, Au/Si(111) systems.
The initial growth process and surface structure of thin Pd(silicide) films on clean Si(111)-7x7 surfaces have been studied by low energy ion scattering (ISS) and LEED-Auger techniques. Considerable reaction between Pd and Si at room temperature is observed to extend up to 25 ML thickness of deposited Pd. Heat treatment of the room temperature film produced epitaxial silicide Pd_2Si(0001) films covered with the accumulated elementary Si layers of 1-2 ML thickness. Deposition of 1/3 ML Pd onto a heated substrate gives a Pd-embedded ordered surface of Si(111)-#sq root#3x#sq root#3R30"0, the feature being similar to the cases of Ag, Au/Si(111) systems. (orig.).
Acute {gamma}-irradiation of rats at doses of 100 and 270 Gy stimulates lipid synthesis and changes the lipid composition of liver cell organelles. The content of cholesterol and cholesterol esters in microsomes increased at 100 Gy and decreased at 270 Gy, with total phospholipid content remaining unchanged. The lipid content in mitochondria decreased considerably 1 h after irradiation at 270 Gy. This change was significantly less pronounced 47 h later. Under chronic {gamma}-irradiation (0.129 Gy/day), cholesterol and cardiolipin in mitochondria increased. The changes in lipid content caused by acute irradiation are presumed to be related to activated synthesis of lipids in the liver. The modification of the lipid content of mitochondria observed in chronically irradiated rats may indicate that energy-metabolizing liver cell systems are involved in the adaptation to irradiation.
Tests using reconstituted samples have been performed to assess the diffusive transport of 137Cs and 60Co through natural regolith materials from a region in South Australia being considered for a radioactive waste repository. A double diffusion cell apparatus made of polycarbonate resin was developed to estimate the effective diffusion (De) and sorption coefficients (Kd) that allowed large withdrawals from the source and collector cells and has enabled tests with low concentrations of radioactivity. An alternative to porous stainless steel filter plates has also been used to reduce uncertainty in test interpretation. Analysis of the transient data used a staged method of the Laplace transform to take into consideration the volume of the samples withdrawn from the apparatus during testing....
Nano indentation analysis and transmission electron microscopy observation were performed to investigate a microstructural evolution and its influence on the hardening behavior in Fe-Cr alloys after an irradiation with 8 MeV Fe4+ ions at room temperature. Nano indentation analysis shows that an irradiation induced hardening is generated more considerably in the Fe-15Cr alloy than in the Fe-5Cr alloy by the ion irradiation. TEM observation reveals a significant population of the a0 dislocation loops in the Fe-15Cr alloy and an agglomeration of the 1/2a0 dislocation loops in the Fe-5Cr alloy. The results indicate that the a0 dislocation loops will act as stronger obstacles to a dislocation motion than 1/2a0 dislocation loops.
Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.
Fe-Cr amorphous films have been formed by both in situ evaporation of multilayered films and ion beam mixing in a target chamber of a 200 keV implanter. The effects of Cr content and ion irradiation on the amorphization of films were examined by transmission electron microscope (TEM). Corrosion of film was investigated by means of a potential dynamic polarization. Corrosion resistance of amorphous film in 0.5 mol H-2SO-4 solution is considerably increased than that of pure iron. Using X ray photoelectron spectroscopy (XPS) corrosion resistance in atmosphere of amorphous Fe-Cr passive films formed by P"+ mixing was studied. Results show that the richness of Cr and P exist at the surface of Fe-Cr film.
Natural rubber (NR) and its derivatives as renewable and biodegradable materials have attracted considerable attention because of the serious pollution problems caused by synthetic materials and a shortage of resources. A new semi-interpenetrating polymer network (semi-IPN) based on epoxidised natural rubber and polyvinyl alcohol containing maleic acid as a crosslinking reagent was synthesized and characterized by FTIR, XRD, SEM, swelling ratio in both distilled water and toluene, and mechanical properties. The curing time and dose of maleic acid were varied from 10 to 60min, and from 10 to 60% (w/w), respectively. An IR spectroscopic study indicated the presence of an ester linkage at 1730cm-1 in maleic acid crosslinked with PVA in semi-IPN films. In addition, the crystalline content of P...
This paper presents three non-linear asymptotic observers corresponding to three examples of engineering interest: a chemical reactor, a non-holonomic car, and an inertial navigation system. For each example, the design is based on physical symmetries. This motivates the theoretical development of invariant observers, i.e, symmetry-preserving observers. We consider an observer to consist in a copy of the system equation and a correction term, and we give a constructive method (based on the Cartan moving-frame method) to find all the symmetry-preserving correction terms. They rely on an invariant frame (a classical notion) and on an invariant output-error, a less standard notion precisely defined here. For each example, the convergence analysis relies also on symmetries consideration with a key use of invariant state-errors. For the non-holonomic car and the inertial navigation system, the invariant state-errors is shown to obey an autonomous differential equation ...
In radio signal-based observing systems, such as Global Positioning System (GPS) and Interferometric Synthetic Aperture Radar (InSAR), the water vapor in the atmosphere will cause delays during the signal transmission. Such delays vary significantly with terrain elevation. In the case when atmospheric delays are to be eliminated from the measured raw signals, spatial interpolators may be needed. By taking advantage of available terrain elevation information during spatial interpolation process, the accuracy of the atmospheric delay mapping can be considerably improved. This paper first reviews three elevation-dependent water vapor interpolation models, i.e., the Best Linear Unbiased Estimator in combination with the water vapor Height Scaling Model (BLUE?+?HSM), the Best Linear Unbiased Es...
An international conference on forestry research presented papers on topics including forest mensuration, growth and yield; growth/yield relationships; design, performance, and evaluation of experiments; forest resource inventory and monitoring techniques; forest management, planning, and managerial economics; forestry and rural development in developing countries; forestry in sustainable economic development; conceptual advances in multiple-use forestry evaluations; economic evaluation of forest damages; supply and demand of roundwood and forest industry products; forestry and rural development in industrialized countries; analysis and evaluation of forest policies; forest institutions and organizations; biological and economic considerations when harvesting young thinning stands; applied sector modelling; and structural changes of the forest sector in a global perspective. Separate abstracts have been prepared for 3 papers from this conference.
Global supply chain practices and their effects have received considerable attention over the last two decades. In the recent past, the need for integration across supply chains has been identified as a key for effective and efficient operations of supply chains. This is observed with the increasing trend of collaborative partnerships among supply chain partners. This paper presents an integrated approach for manufacturing and distribution networks within the supply chain system of a global car company. The paper shows that the integration of manufacturing and distribution networks creates the environment for effective planning of many components and execution/follow-up of those plans. These components include materials, resources, operations/activities, suppliers and customers. The main f...
A detailed discussion of airborne CO{sub 2}, DIAL measurements obtained from the first joint N-ABLE field campaign at INEL is presented. System performance characteristics, including return signal strength, averaging statistics, and temporal correlation as well as multi-line DIAL spectral data are discussed. In particular, we review data acquisition and analysis strategies pertinent to chemical detection from a moving platform, such as range determination and correction, and return signal processing (waveform vs. box-car integration, baseline correction). We also report observed effects and variations due to near-field light scattering, pointing and tracking stability, and stack-release plume dynamics.
The effect of NaCl and Na_2SO_4 treatments on chlorophyll content, rate of "1"4C assimilation and products of photosynthesis in peanut (Arachish hypogaea L.) variety TMV-10 has been investigated. It was observed that chlorophyll content was affected mainly by NaCl, Na_2SO_4 treatment lowered the rate of photosynthetic "1"4CO_2 fixation. The analysis of labelled products revealed that the salts affect the carbon metabolism differently. The radioactivity was found to be accumulated in fractions of sugars and sugarphosphates in the leaves of NaCl treated plants. Na_2SO_4 treatment brought about considerable decline in labelling of sugars and an increase in labelling of amino acids and sugarphosphates. (orig.).
The influence of the regimes of modification of carbon fibers by an argon ion beam on the change in the angle of their wetting by an epoxy oligomer has been investigated. It has been shown that ion-beam treatment of carbon fibers leads to a considerable decrease in the wetting angles (the difference between the wetting angles for non modified and modified fibers is up to 32.2-38.7). Accordingly, there is also an increase in the value of the equilibrium work of adhesion by 36.2-41.6% in the contact zone. It has been established that ion-beam treatment of carbon fibers by argon ions leads to an increase in the shear strength when microplastics based on them are formed. (authors)
Dynamic stability enhancement of composite mode oscillations of interconnected power systems by means of a hybrid power system stabilizer is discussed here. The proposed Hybrid PSS is of a two-level structure composed of a local PSS for local mode and a global PSS for inter-area mode damping. Here, the input of the global stabilizer is the center of inertia speed deviation of slow-coherent generators. The paper is focused on the practical considerations in implementation of the proposed stabilizer. First, the optimum allocation of this stabilizer is discussed. The authors introduce an index of mode-input-assignability, by which the best sites of the stabilizer can be identified. Next, for practical applications, an estimation method for the approximation of the input of the global PSS is introduced. An approximated value of the center of inertia speed is obtained from a suitable combination of the rotor speed data of a few properly selected key generators.
This article focuses on visual representations of subjective experiences of the process of recovery from addiction and the meanings that participants attribute to their visual work. The data are drawn from a study of six female participants. In this article, we discuss the results with reference to one participant, to allow for detailed consideration of the visual and the verbal material. This participant was selected because of the richness of her material, which provided an opportunity to carry out a detailed case study. Potential participants were informed in advance that they would be asked to draw during the interview. They were also asked to bring to the interview some artwork made during their engagement in creative activities at an earlier stage in their recovery. The data were ana...
The 575-mile Statpipe gas transportation system entails 191 miles of wet-gas line running from the Statfjord field across the Norwegian trench to the Karsto, Norway, conditioning plant and 384 miles of dry-gas line from Karsto, again across the trench, to the Heindal and Sleipner fields for final connection at Ekofisk with the Norpipe system for transport to Emden, West Germany. Special construction considerations include the 1000-ft-deep trench crossings, the rocky shore approach and departure, and the subsea tie-ins required at depths of up to 500 ft. The system has an initial annual design capacity of 186 billion CF of wet gas and 260 billion CF through the dry-gas line to Emden.
The purpose of the Hanford Waste Management Plan (HWMP) is to provide an integrated plan for the safe storage, interim management, and disposal of existing waste sites and current and future waste streams at the Hanford Site. The emphasis of this plan is, however, on the disposal of Hanford Site waste. The plans presented in the HWMP are consistent with the preferred alternative which is based on consideration of comments received from the public and agencies on the draft Hanford Defense Waste Environmental Impact Statement (HDW-EIS). Low-level waste was not included in the draft HDW-EIS whereas it is included in this plan. The preferred alternative includes disposal of double-shell tank waste, retrievably stored and newly generated TRU waste, one pre-1970 TRU solid waste site near the Columbia River and encapsulated cesium and strontium waste.
It is shown that a gun similar to that in the SSPX could demonstrate the high fields required for Pulsed Spheromak reactors merely by prolonging the pulse. Important considerations are choosing the voltage to exceed ohmic losses; designing the gun to avoid wasteful short-circuiting of current within the gun; and the injection efficiency factor, f, determined by the ''sag'' in the profile of {lambda} = {mu}{sub o}j/B. Typically f = 0.75 in experiments, giving an overall efficiency > 50 % if short-circuiting is avoided. Theoretical transport models agree qualitatively with the need for a finite gradient in h to pump in helicity by current-driven tearing modes and suggest that pressure-driven resistive modes would not compete with current-driven modes during a buildup to ohmic ignition.
Through the dedicated collaborative efforts of many individuals interested in supporting local education, computer laboratories were established at two urban high schools. The purchasing and implementation of the project was handled by the Alliance for Education, a local non-profit education advocate. Funds were supplied by the Air Force as part of a 3-year research activity utilizing artificial intelligence technology to tutor 9th grade students. NCR (now AT7T Global Information Solutions) corporate leaders provided the computers and network equipment at a considerable savings to the project. Each lab is a state-of-the-art facility with air-conditioning, carpeting, special computer tables, computer projection screens, and on-site technical support. Student and teacher enthusiasm toward the project has been gratifying and quantitative results are currently being evaluated for both attitude, skills, and state proficiency tests.
The concepts of general flow and thermal boundary conditions are introduced to treat the interaction between indoor and outdoor thermal environments in computational fluid dynamics (CFD) simulations. The results from a multi-zone model are used to supply the general flow boundary conditions. The energy balance equation at wall-air interfaces is used to supply the general thermal boundary conditions. An example calculation in a 13-room building shows that infiltration influences indoor air flow patterns considerably. The air flow in a room ventilated by displacement is measured and simulated. Two surface coatings are considered, i.e. black walls and aluminum walls. Implementation of these two boundary conditions is essential in predicting air flow patterns, air quality, and thermal comfort in a real building. (author)
Shaped charges were first used more than 30 years ago to perforate casing, cement sheath and reservoir to provide selective communication between the reservoir and well bore. Since then, advances have been made in design of shaped charge sand ancillary equipment. Penetration has increased considerably. Miniaturization of equipment allows passing through relatively small restrictions and effectively communicating with reservoirs. Gun debris has been drastically reduced and in some designs eliminated. Deep reservoirs can be effectively penetrated under down-hole environments exceeding 500 F and 20,000 psi. This work covers the problems encountered and reviews successful devices employing shaped charge and explosive technology.
Shadow effect was used for investigating damage of uranium dioxide monocrystal. The dependence of shadow minimum parameters on fluence of "2"2Ne ions with 172 MeV energy was followed when detecting fission fragments. Ion dose responsible for sufficient microdamage of lattice structure, included into the classification of heavy ion damage effect on monocrystals was determined. The problem of radiation intensity effect on the character of occurred damages was studied. It was established that macroscopic sample failure, caused by generation of considerable mechanical stresses in monocrystal under beam effect could be observed along with microdamages of lattice structure at ion flux density >10"1"2 cm"-"2Xs"-"1.
The mass asymmetry of fragments from nuclear fission of heavy nuclei is reviewed. While mass asymmetry is a common and well-known phenomenon for low-energy fission of the lighter actinides, more recent experiments have demonstrated that, for the heaviest actinides, the mass distribution switches to a symmetric one. On the other hand, it has been discovered that, though for fissioning nuclei with mass numbers A< or [approx]225 the mass distribution is basically symmetric, an asymmetric component is clearly to be identified for nuclei down to the Pb-region. In the absence of a generally accepted dynamical theory of fission, the above experimental findings are discussed in terms of static energy considerations. Triggered from the outset by the structure of the potential energy surface at the saddlepoint, the energy balance at the scission point between the available energy (Q-value) of the reaction and the Coulomb and deformation energy of the nascent fragments is ...
The mass asymmetry of fragments from nuclear fission of heavy nuclei is reviewed. While mass asymmetry is a common and well-known phenomenon for low-energy fission of the lighter actinides, more recent experiments have demonstrated that, for the heaviest actinides, the mass distribution switches to a symmetric one. On the other hand, it has been discovered that, though for fissioning nuclei with mass numbers A< or #approx#225 the mass distribution is basically symmetric, an asymmetric component is clearly to be identified for nuclei down to the Pb-region. In the absence of a generally accepted dynamical theory of fission, the above experimental findings are discussed in terms of static energy considerations. Triggered from the outset by the structure of the potential energy surface at the saddlepoint, the energy balance at the scission point between the available energy (Q-value) of the reaction and the Coulomb and deformation energy of the nascent fragments is ...
The VNC2 and VNC5 steel tests on endurance were carried out in order to determine the capacity for work of large welded samples and to investigate the methods of welding. The samples made by the arc welding demonstrated the most high endurance at low frequencies of loading during the test of welded joints made of the VNC2 steel. The application of the VNC2 steel interlayers together with intermediate heat treatment allows one to increase the static and fatigue strength of welded joints at corresponding decrease of the construction weight during welding of the VNC5 steel as well as its combination with the VNC2 steels. The gas protection deterioration during steel welding leads to considerable diversity of values of endurance.
Comparative indices are given for the efficiency of phase control of remote-controlled self-compensating high-voltage transmission lines, including a consideration of the power transfer effect between high-voltage line circuits. A description is given of certain circuit variations for performing the technical means of regulating phase shift, and their characteristics which make it possible to evaluate the effect of the phase regulators on the electrical transmission system are also given. An examination is made of problems concerned with the design of lines, relay protection, computation of transfer processes and dynamic stability as well as the computation of over-voltage when shutting off short circuits during amplified electromagnetic ties between line circuits.
The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).
The effect of complexing agents DTPA and H2C2O4 on the extraction-chemical behavior of Tc, as applied to extractive splitting of U and Pu in the Purex process, was studied. The kinetic relationships of catalytic decomposition of N2H5NO3 under the action of Tc in the presence of these agents were determined. Variation of the ratio of the oxidized and reduced Tc species in the course of this process at various HNO3 concentrations was examined. In the final step of the reaction of N2H5NO3 with Tc in a nitric acid solution, when the reductant content is stabilized, the oxidation of reduced Tc also stops or continues at a considerably lower rate than before stabilization. The presence of DTPA decreases the rate of Tc(IV) oxidation owing to its binding in a complex and decreases the fraction of ...
An interesting line of research is the investigation of the laws of random variables known as Dirichlet means. However, there is not much information on interrelationships between different Dirichlet means. Here, we introduce two distributional operations, one of which consists of multiplying a mean functional by an independent beta random variable, the other being an operation involving an exponential change of measure. These operations identify relationships between different means and their densities. This allows one to use the often considerable analytic work on obtaining results for one Dirichlet mean to obtain results for an entire family of otherwise seemingly unrelated Dirichlet means. Additionally, it allows one to obtain explicit densities for the related class of random variables that have generalized gamma convolution distributions and the finite-dimensional distribution of their associated L\\'{e}vy processes. The importance of this latter statement is ...
Abstract BACKGROUND: Dietary plant materials have attracted much attention because of their health benefits to humans. Acrylamide is found in various heated carbohydrate-rich foods. Our previous results showed that crude aqueous extracts from diverse dietary plants and some phenolic compounds could mitigate acrylamide formation in an asparagine-glucose model system. Based on our previous study, several plant materials were selected to further investigate their inhibitory effects on acrylamide formation in cookies and starch-based model systems. RESULTS: Addition of raw powders from selected dietary plants and their crude aqueous extracts could considerably reduce acrylamide formation in both cookie and potato starch-based models. Aqueous extracts of clove at 4% caused the largest reduction...
Evidence for dietary/nutritional treatments of attention-deficit/hyperactivity disorder (ADHD) varies widely, from double-blind, placebo-controlled trials to anecdotal. In guiding patients, clinicians can apply the SECS versus RUDE rule: treatments that are Safe, Easy, Cheap, and Sensible (SECS) require less evidence than those that are Risky, Unrealistic, Difficult, or Expensive (RUDE). Two nutritional treatments appear worth general consideration: Recommended Daily Allowance/Reference Daily Intake multivitamin/mineral supplements as a pediatric health intervention not specific to ADHD and essential fatty acids, especially a mix of eicosapentaenoic acid, docosahexaenoic acid, and ?-linolenic acid as an ADHD-specific intervention. Controlled studies support the elimination of artificial fo...
Sols of silver nanoparticles in toluene were studied by broadband dielectric spectroscopy (10?3?105 Hz). The frequency dependences of the specific alternating current (ac) conductivity and the complex electric modulus were used to estimate the temperature/frequency intervals of long- and short-range charge transfer occurs, respectively. A considerable increase (by more than 30 ?C) in the Vogel temperature T 0 and the glass transition temperature T g in sols compared with the pure solvent was found. It can be hypothesized that these cooperative effects reflect the initial stage of the superlattice formation. Although the dielectric characteristics of sols are generally controlled by the conductivity relaxation, the dielectric response was observed in the high-frequency range (1?103 Hz) at l...
About every 12 years, asphalt roads must be reworked, and this is usually done by placing thick layers (hot-mix overlays) of new material on top of failed material, resulting in considerable waste of material and use of new asphalt binder. A good recycling agent is needed, not only to reduce the viscosity of the aged material but also to restore compatibility. Objective is to establish the technical feasibility (Phase I) of determining the specifications and operating parameters for producing high quality recycling agents which will allow most/all the old asphalt-based road material to be recycled. It is expected that supercritical fractionation can be used. The advanced road aging simulation procedure will be used to study aging of blends of old asphalt and recycling agents.
The economy of medicinal plant production is burdened considerably by the energy costs of drying. To substitute fossil energy, a solar heated dryer was developed, taking a plastic film greenhouse as superstructure to lower the initial costs. The solar air heaters, being incorporated into the roof, consist of a black absorber tissue, which is placed between the transparent cover of the greenhouse and an insulating air-bubble foil. To obtain a modular design, the system is structured along the ridge into segments of 2 m width. Each segment forms an independent solar air heater/batch dryer unit and is operated by a fan with a power consumption of 500 W. A prototype was tested in Yugoslavia, drying mint, sage and hops. (author).
Phenomena in power systems tend to exhibit higher nonlinearity, because efficient operation accompanies severer power transfer. In such cases, there might exist some limitation to the use of conventional linear control design scheme due to the nonlinearity. As for consideration to the nonlinearity, we have developed a nonlinear analysis method based on normal form theory. In this paper, we develop a new control design scheme based on the nonlinear analysis method. The developed method is effective in a case when oscillatory instability occurs. In the developed method, the parameters of control devices are adjusted so as to enlarge the stability limit against the oscillatory instability, unless each eigenvalue exceed its allowable threshold. We verify the effectiveness of the developed method in the IEEJ 10-machine System Model by applying to PSS (Power System Stabilizer). We show that the power transfer limit increases by a few percent.
Experiments have been performed to study the usefulness of several types of plastic foils as filter to separate radon and thoron. Time-integrated alpha-activity measurements have been carried out by using the so-called ''can-technique'' equipped with both LR-115 and CR-39 track detectors. The track density observed on the detectors, taken as a measure of radon activity concentration, has been determined as a function of the thickness of filter foils. The radon permeability and the thoron separation factors have been determined. It is shown that various plastic foils exhibit considerable differences in radon diffusion coefficient owing to their different chemical structures. Among the plastic foils investigated the polyethylene proved to have the highest gas diffusion coefficient.
Georg Fischer GmbH operates a melting plant with several cupola furnaces in Mettmann. The plant supplies two casting plants for production of castings from nodular cast iron or malleable cast iron. It is now planned to convert one of the existing hot-blast cupola furnaces to the latest state of the art. Under special consideration are clear reduction of dust emission by use of a filtering separator below the permissible mass concentration according to the Clean Air Regulations; reduction of the current level of dumped waste by application of a new dust (residue) utilisation method; improvement of the total thermal efficiency of the cupola furnace melting plant by extensive, advanced utilisation of waste heat; and use of low-cost dust-like alternative fuels. (author).
The concept of the 'white-light cavity' has recently generated considerable research interest in the context of gravitational wave detection. Cavity designs are proposed using negative (or anomalous) dispersion in an intracavity medium to make the cavity resonate over a large range of frequencies and still maintain a high cavity build-up. This paper presents the first experimental attempt and demonstration of white-light effect in a meter long ring cavity using an intracavity atomic medium. The medium's negative dispersion is caused by bi-frequency Raman gain in an atomic vapor cell. Although the white light condition was not perfectly achieved and improvements in experimental control are still desirable, significantly broad cavity response over bandwidth greater than 20 MHz has been observed. These devices will have potential applications in new generation laser interferometer gravitational wave detectors.
Experimental studied of deep-inelastic scattering of neutrino, antineutrino, #mu#-mesons, electron reactions on He, D, Al, Fe, Au, Be, C, Ca, Ag, N nuclei conducted in recent years at different laboratories the world for consideration of modern status of the problems of R(x, Q"2) = #sigma#sub(L)/#sigma#sub(T) parameter variation and for study on nuclear effects in structural functions of nucleons are described in the review. Experimental information on measurements of the R parameter by data on EMS and SLAK groups is analyzed. It is noted that experimental data on measuring R contain essential errors that hampers unambiguous interpretation of data on nucleon structure. Present experimental data and predictions for explanation of the EMS effect are analyzed from the view point of quark and flucton models of a nucleus.
This article analyses the prevalent situation of the formal Financial Institutions (FIs) in rural India using data from National Sample Survey 54th Round (January-June, 1998). We use sample selectivity model to examine the sanction of the loan by the FIs as a two-stage process. We model the choice of the household's credit requirement using an unordered choice model, namely, a multinomial logit model. Our results reveal that the rural households are considerably credit constrained. The households who do not have an account in a FI have a lower chance of obtaining the loan and households who are credit constrained have relatively lower land holding and they do not possess livestock. Households who borrow for nonfarm purpose exhibit a lower chance of obtaining credit compared to those househ...
Abstract The fit of patient coping style and psychotherapy focus has been suggested as improving treatment outcome. This article reviews the definitions, measures, and previous research surrounding this hypothesis. An original meta-analysis of 12 carefully selected studies (N = 1,291 patients) resulted in a weighted, mean effect size (d) of .55 in favor of a fit between externalizing patients and symptom-focused treatment or, alternatively, internalizing patients and insight-focused treatment. This medium-size effect indicates that nondiagnostic patient factors, like coping style, are important considerations in the selection of effective therapies. Clinical examples and clinical recommendations are provided. 2010 Wiley Periodicals, Inc. J Clin Psychol: In Session 67:176-183, 2011.
Purpose Nonpoint sources (NPS) pollution has been an important cause for water quality impairment worldwide. To take the temporal variations of both NPS pollution and in-stream attenuation into consideration, an inverse modeling approach and the load duration curve (LDC) method were combined for variable nutrient total maximum daily load (TMDL) development. Methods Water quality and hydrological parameters were monitored monthly along the ChangLe River system in 2004?2008. The catchment NPS export load (EL) and TMDL for total nitrogen (TN) were estimated by the inverse format of an existing stream nutrient transport equation. The LDC method was used to describe the variability of EL, TMDL, requiring load (RLR) and percent (the ratio between the RLR and the EL, RPR) reduction, and then to s...
The relationships between changes in energy metabolism and the antioxidant defense system in the weed species Ipomoea triloba L. during seed germination and early seedling growth were investigated. The effects of some common allelochemicals on these parameters also were studied. Respiratory activity and the activities of alcohol dehydrogenase, superoxide dismutase, catalase, guaicol peroxidase, ascorbate peroxidase, glutathione reductase, and lipoxygenase were measured. Mitochondrial oxidative phosphorylation resumed shortly after the seed imbibition period, as indicated by considerable KCN-sensitive respiratory activity in embryos of I. triloba. The occurrence of superoxide dismutase, catalase, guaicol peroxidase, and lipoxygenase activities in the embryos, along with significant KCN-inse...
Electromagnetic forming (EMF) is a forming process that relies on the inductive electromagnetic force to deform metallic workpiece at high speed. Calculation of the electromagnetic force is essential to understand the EMF process. However, accurate calculation requires complex numerical solution, in which the coupling between the electromagnetic process and the deformation of workpiece needs be considered. In this paper, an appropriate formula has been developed to calculate the electromagnetic force in metal work-piece in the sheet EMF process. The effects of the geometric size of coil, the material properties, and the parameters of discharge circuit on electromagnetic force are taken into consideration. Through the formula, the electromagnetic force at different time and in different positions of the workpiece can be predicted. The calculated electromagnetic force and magnetic field are in good agreement with the numerical and experimental results. The accurate ...
Steel building frames are often analyzed for stability in an elastic way, while most of their columns behave inelastically at the buckling stage. Most column design provisions allow for inelastic behavior, but overall inelastic stability analysis is rarely performed. In this study the analysis philosophy is centered on the overall frame stability and its true safety factor. As many columns show inelastic behavior at the buckling stage, the proposed procedure takes due consideration of this fact. Once the overall buckling factor for the frame is obtained, individual column effective length factors, and their true slenderness ratios are computed, and used in the design relationships. This procedure circumvents the use of design nomographs and numerous formulas proposed in the past to allevia...
SIMS measurements revealed that high energy boron-implantation causes transient enhanced diffusion (TED) of a shallow dopant profile due to Si interstitials even for a relatively low dose of {approximately}2E13cm{sup {minus}2}. By systematic analysis, it is found that this anomalous diffusion is most significant in 700--800 C annealing, and it takes place in the initial stage (less than 30 sec for 800 C) of annealing. Moreover, this anomalous diffusion is more considerable than the enhanced diffusion during oxidation (OED) in practical device fabrication processes. It is found that rapid thermal annealing (RTA) at 1,000--1,100 C is effective for suppressing the transient enhanced diffusion and realizing a shallow channel profile for deep sub-micron devices.
SIMS measurements revealed that high energy boron-implantation causes transient enhanced diffusion (TED) of a shallow dopant profile due to Si interstitials even for a relatively low dose of #approx#2E13cm"-"2. By systematic analysis, it is found that this anomalous diffusion is most significant in 700--800 C annealing, and it takes place in the initial stage (less than 30 sec for 800 C) of annealing. Moreover, this anomalous diffusion is more considerable than the enhanced diffusion during oxidation (OED) in practical device fabrication processes. It is found that rapid thermal annealing (RTA) at 1,000--1,100 C is effective for suppressing the transient enhanced diffusion and realizing a shallow channel profile for deep sub-micron devices.
Composting is once again gaining interest among ecological engineers in view of greener industrial and residential activities. Uniform composting is needed to ensure decomposition and to keep the whole system at the same composting stage. A homogeneous temperature must be maintained throughout the media. A bioreactor design consisting of a heater core made of copper tubing was designed and tested. Two four-inch holes were made at the top and bottom of the barrel to allow air to flow through the system and promote aerobic composting. Once composting began and temperature increased, the water began to flow through the copper piping and the core heat was distributed throughout the medium. Three thermocouples were inserted at different heights on a 200 litre plastic barrel fitted with the aforementioned apparatus. Temperature variations were found to be considerably lower when the apparatus was operated with the heat redistribution system, enabling uniform composting, ...
The stages of processes leading to radiation damage are studied, as well as, the direct and indirect mechanics of its production. The radiation effects on nucleic acid and protein macro moleculas are treated. The physical and chemical factors that modify radiosensibility are analysed, in particular the oxygen effects, the sensibilization by analogues of nitrogen bases, post-effects, chemical protection and inherent cell factors. Consideration is given to restoration processes by excision of injured fragments, the bloching of the excision restoration processes, the restoration of lesions caused by ionizing radiations and to the restoration by genetic recombination. Referring to somatic effects of radiation, the early ones and the acute syndrome of radiation are discussed. The difference of radiosensibility observed in mammalian cells and main observable alterations in tissues and organs are commented. Referring to delayed radiation effects, carcinogeneses, ...
A brief overview is given of a report on Emergency Core Cooling Systems (ECCS) Recirculation Reliability Knowledge Base compiled by the International Working Group on ECCS Reliability for the OECD/NEA/CSNI. Four safety issues are identified which arise in the context of loss of coolant accidents (LOCAs) and are connected with materials and/or processes that interfere with the ECCS safety function in ways other than just strainer head loss generation. They are: the generation of missiles during a LOCA from encapsulated insulation materials used to reduce insulation debris production; clogging of BWR pressure suppression containment vent pipes by insulation jackets or metallic insulation foil pieces; strainer or sump debris ingestion and the effects of ingested debris on ECCS equipment and core cooling; miscellaneous items such as material aging and self-cleaning strainer concepts. The emphasis is mainly on BWRs but many of the considerations also apply to PWRs. ...
We consider 4-dimensional space-times which are asymptotically flat at spatial infinity and show that, in the first order framework, action principle is well-defined \\emph{without the need of infinite counter terms.} It naturally leads to a covariant phase space in which the Hamiltonians generating asymptotic symmetries provide the total energy-momentum and angular momentum of the space-time. We address the subtle but important problems that arise because of logarithmic translations and super-translations both in the Langrangian and Hamiltonian frameworks. As a forthcoming paper will show, the treatment of higher dimensions is considerably simpler. Our first order framework also suggests a new direction for generalizing the spectral action of non-commutative geometry.
The manual enhances and simplifies the work of those architects and engineers whose practice includes the analysis and modification of existing buildings to reduce both fuel consumption and operating costs. A review of the principles of energy use and conservation is given. The manual also provides a step-by-step methodology for assessing and improving the year-round energy performance of buildings, as well as a series of forms, charts, and nomographs designed to serve as day-to-day tools in the energy professional's toolbox. After a cost-benefit analysis is prepared for each conservation opportunity, the owner will be able to implement decisions based on projected energy savings and calculate investment costs, operational changes, and payback periods. Each of these considerations is accorded a detailed treatment.
A preliminary design for a nuclear electric 'Space Tug' is proposed for use in conjunction with the American Space Shuttle for high energy missions. The vehicle would employ a SNAP 10A/2 or SNAP 8 nuclear reactor derivative for its power supply and slush hydrogen as the working fluid for the electrothermal thrusters. A thermodynamic conversion cycle would be employed for electrical power generation, for which the hydrogen working fluid would perform the duty of the heat sink. The cycle would eliminate the need for heavy waste radiators and improve the overall thermal efficiency. The vehicle promises a considerable payload advantage over a chemical recoverable Tug for geostationary missions. (orig.).
In view of the importance of the material Alloy 800 in high-temperature reactor plants (HTR), a material data bank was established which is used for statistical evaluation of mechanical and physical material behaviour. Based on investigations on the interconnection between the mechanical properties at high temperatures and the metallurgical parameters, different types of Alloy 800 were specified in compliance with the component requirements. In addition, aspects of corrosion and toughness behaviour were taken into consideration. The specifications and strength characteristics for the different variants of Alloy 800 were incorporated into draft DIN standards after discussion and approval in expert committees. Further important characteristics of the mechanical and physical material behaviour were summarized in HTR material data sheets so as to furnish an improved basis for the design and stress analyses of Alloy 800 components. (orig.).
In view of the importance of the material Alloy 800 in high-temperature reactor plants (HTR), a material data bank was established which is used for statistical evaluation of mechanical and physical material behaviour. Based on investigations on the interconnection between the mechanical properties at high temperatures and the metallurgical parameters, different types of Alloy 800 were specified in compliance with the component requirements. In addition, aspects of corrosion and toughness behaviour were taken into consideration. The specifications and strength characteristics for the different variants of Alloy 800 were incorporated into draft DIN standards after discussion and approval in expert committees. Further important characteristics of the mechanical and physical material behaviour were summarized in HTR material data sheets so as to furnish an improved basis for the design and stress analyses of Alloy 800 components. (orig.).
The 5-th International conference 'Nuclear and Radiation Physics' was held in Almaty (Kazakhstan) 26-29 September 2005. Besides basic problems of nuclear and solid state physics the conference paid considerable attention to applied topics important for industry and science in Kazakhstan; they include fuel and construction materials for nuclear power production, new technologies and materials for their production, materials for hydrogen power production, handling and utilization of radioactive waste, analytical methods for combating with illicit trafficking of nuclear and radioactive materials, technologies for reduction and assessment of environmental risk from radiation-hazardous materials and sites, production and application of isotopes, application of nuclear technologies in medicine and industry. On the conference more than 300 papers were presented by participants from 20 countries.
In the present work, the process of carbon dioxide absorption is analyzed at high partial pressures, in aqueous solutions of 1-amino-2-propanol (monoisopropanolamine (MIPA)), in relation to the thermal effects involved. All experiments were made in a stirred-tank reactor with a plane unbroken gas-liquid interface. The variables considered were the MIPA concentration within the range 0.1--2.0 M and the temperature within the interval 288--308 K. From the results, the authors deduce that the absorption process takes place in the nonisothermal instantaneous regime and propose an equation which not only relates the experimental results of flow density with the initial concentration of amine but at the same time enables the evaluation of the rise in temperature in the gas-liquid interface.
Wireless mesh networks can provide low-cost solutions for extending the reach of wireless access points by using multi-hop routing over a set of stationary wireless routers. The routing protocol for these networks may need to address quality considerations to meet the requirements of the user. In this paper, we present a quality based routing protocol for wireless mesh networks that tries to maximize the probability of successful transmissions while minimizing the end-to-end delay. The proposed routing protocol uses reactive route discoveries to collect key parameters from candidate routes to estimate the probability of success and delay of data packets transmitted over them. To achieve accurate route quality assessments, a new route quality metric is proposed that uses performance models ...
In recent years, interest in the development of a polymer electrolyte fuel cell (PEFC) has considerably increased due to its advantages (e.g., high power density) compared with other fuel cell systems, and its potentials to become the power plant for the next generation, nonpolluting automobile engine. For large scale application of fuel cells, low platinum loading electrode structures are necessary. An electrode based on a highly porous carbonized polyacrylonitrile foam material with very low platinum loading ({approximately} 13 {micro}g/cm{sup 2}) was prepared. The performance of this electrode for oxygen reduction was evaluated and compared with bulk platinum and glassy carbon electrodes.
In this work, we propose a conceptual distributed control framework for electrical grid integrated with distributed renewable energy generation systems in order to enable the development of the so-called ''smart electrical grid''. First, we introduce the key elements and their interactions in the proposed control architecture and discuss the design of the distributed control systems which are able to coordinate their actions to account for optimization considerations on the system operation. Subsequently, we focus on a specific wind/solar energy generation system connected to a reverse osmosis water desalination system and the electrical grid and design two supervisory predictive controllers via model predictive control to operate the integrated system taking into account short-term and lo...
A concept for the optimization of manufacturing processes of composite material components with regard to product's quality and cost is introduced and applied for the case of thermoplastic composite helicopter canopies produced by `Cold' Diaphragm Forming (CDF) process. The proposed methodology relies on the consideration of the processes thermal cycle as decisive for the component's quality and cost. Quality and cost sensitivity analyses were made to derive material dependent Quality Functions (QFs) and process dependent Cost Estimation Relationships (CERs). QFs and CERs are exploited to derive iteratively the optimal thermal cycle. The processes thermal cycle is numerically simulated to allow for its virtual application on the material. To perform the optimization procedure a new softwar...
In the aftermath of the 9/11 terrorist attacks on the United States, there was heightened interest worldwide in protecting nuclear power plants against intentional aircraft attack by terrorists. This paper presents our perspective into regulatory requirements for intentional aircraft crash that were set forth in foreign countries, including the latest rulemaking by the U.S. Nuclear Regulatory Commission (NRC), i.e., 10 CFR 50.54(hh) and 10 CFR 50.150 that have been made effective in May and July of 2009, respectively. In light of these international efforts to further enhance safety of NPPs, a study is also underway at the Korea Institute of Nuclear Safety (KINS) to establish an effective and efficient regulatory approach in consideration of the state of the art in this area
Starting from the Plebanski formulation of gravity as a constrained BF theory we propose a new spin foam model for 4d Riemmanian quantum gravity that generalises the well-known model of Barrett-Crane and resolves the ultralocality problem that this model is known to possess. It is well known that the BF formulation of 4d gravity possesses two sectors: one corresponding to gravity and the other topological. The model presented here is shown to give a quantisation of the gravitational sector. The present model is dual to the recently proposed spin foam model of Engle et al. which, we show, corresponds to the topological sector of the theory. One important outcome of our approach is that it also allow us to introduce the Immirzi parameter into the framework of spin foam quantisation. We generalize some of our considerations to the Lorentzian setting and obtain a new spin foam model in that context as well.
Theoretical and experimental data which have defined and/or extended the effectiveness of remote sensing operations are explored, with consideration given to both scientific and commercial activities. The remote sensing of soil moisture, the sea surface, and oil slicks is discussed, as are programs using satellites for studying geodynamics and geodesy, currents and waves, and coastal zones. NASA, Canadian, and Japanese radar and microwave passive and active systems are described, together with algorithms and techniques for image processing and classification. The SAR-580 project is outlined, and attention is devoted to satellite applications in investigations of the structure of the atmosphere, agriculture and land use, and geology. Design and performance features of various optical scanner, radar, and multispectral data processing systems and procedures are detailed.
Vehicular communication (VC) systems have recently drawn the attention of industry, authorities, and academia. A consensus on the need to secure VC systems and protect the privacy of their users led to concerted efforts to design security architectures. Interestingly, the results different project contributed thus far bear extensive similarities in terms of objectives and mechanisms. As a result, this appears to be an auspicious time for setting the corner-stone of trustworthy VC systems. Nonetheless, there is a considerable distance to cover till their deployment. This paper ponders on the road ahead. First, it presents a distillation of the state of the art, covering the perceived threat model, security requirements, and basic secure VC system components. Then, it dissects predominant assumptions and design choices and considers alternatives. Under the prism of what is necessary to render secure VC systems practical, and given possible non-technical influences, ...