International Nuclear Information System (INIS)

Available in abstract form only. Full text of publication follows: In this study. simulation of carbon dioxide absorption by Sodium Hydroxide solution in a packed bed has been investigated. At first, mass and energy balances were applied around a differential height of the bed. So, the governing equations were obtained. Surface renewal theory by Danckwerts was used to represent the mass transfer operation Finally, by changing the operating parameters like solvent temperature, inlet gas composition pressure and height of the bed, the effect of these parameters on the absorption and the composition of carbon dioxide in exit stream have been investigated. (authors)

Energy Technology Data Exchange (ETDEWEB)

In the new system presented in this paper, the cement clinker is sintered, not in a rotary kiln, but in two different furnaces: a spouted bed kiln and a fluidized bed kiln. The heat generated in the process of cooling the cement clinker is recovered by a fluidized bed cooler and a packed bed cooler, which are more efficient than the conventional coolers. Compared with the rotary kiln system, the new technology significantly reduces NO{sub x} emissions, appreciably cuts energy consumption, and reduces CO{sub 2} emissions as well. Thus, the new system is an efficient cement sintering system that is friendly to the global environment. In this paper, we describe this new technology as one of the applied technologies at an industrial level that is being developed in the Clean Coal Technology Project, and we present the results from test operations at our pilot plant.

Energy Technology Data Exchange (ETDEWEB)

The authors report a novel configuration for a zinc-particle, packed-bed anode in which an open structure of high hydraulic permeability is maintained indefinitely in a cell with closely spaced walls by the formation of particle bridges and associated gaps. The configuration minimizes electrolyte pumping costs, allows rapid refueling and partial recharge, and provides for 100% zinc consumption. This approach benefits zinc/air fuel batteries by allowing nearly continuous operation and fuel recycle without commercial infrastructure; it benefits Zn/[Fe(CN){sub 6}]{sup {minus}3} batteries by eliminating shape-change and polarization problems found with planar anodes.

Energy Technology Data Exchange (ETDEWEB)

The use of aqueous methyldiethanolamine (MDEA) for selective removal of hydrogen sulfide from acid gas streams has been studied in a 2 inch column packed with 1/4 inch ceramic Intalox saddles. The column was operated in a counter-current, steady state fashion. The feed gas composition varied between 1 and 5 mole % hydrogen sulfide and between 0 and 50 mole % carbon dioxide. In order to assist the development of packed column absorption models, the rate at which pure carbon dioxide absorbs into 2 M MDEA was measured as a function of pressure, liquid flow rate and packed bed length. The importance of end effects was carefully evaluated. In addition, draining and tracer methods were used to estimate the amount of static holdup present in the column. Using classical draining methods, as much as 50 % of the total holdup was found to be static. However, according to the step decrease in tracer method, less ...

Energy Technology Data Exchange (ETDEWEB)

A three-dimensional mathematical model has been developed as a tool for furnace structure design and operation conditions optimization when the straw combustion is in oxygen-enriched or conventional air atmospheres. Mathematical methods have been used based on a combination of FLIC (A fluid Dynamic Incinerator Code) code for the in-bed incineration and commercial software FLUENT for the over-bed combustion. Oxygen-enriched atmospheres promote the destruction of most pollutants due to the high oxygen partial pressures and temperatures, which is reflected by very low residual amounts of organic combustion by-products in the bottom ash and flue gas of the straw-fired boiler unit. The predictions indicated that the maximum combustion temperature is around 1500 K, CO emission is 201 vppm and O{sub 2} concentration is about 6.9 vol% at furnace exit, and it is shown that mathematical models can serve as a reliable tool for detailed analysis of straw ...

Science.gov (United States)

...furnished with commercial or military export packing. Military export packing, if offered, shall be in accordance with Mil-Std-2073-1 Level A or B as specified. If commercial export packing is offered, the offer or pricelist shall include...

Energy Technology Data Exchange (ETDEWEB)

The following paragraphs summarize the progress of each research project funded under the WVU Cooperative Agreement during the third quarter of 1997 (July - September 1997). The projects are arranged according to their 1997 WVU task number. WVU Focus Area 1.0: Subsurface Contaminants, Containment and Remediation Task No. 1.1: Project discontinued. Task No. 1.2: Development of Standard Test Protocols and Barrier Design Models for Desiccation Barriers (K. Amininan & S. Ameri): A number of experiments were preformed this period to evaluate the ability of the dried sand-packs to act as a barrier to liquids. Water infiltration tests were done with a constant head, dispersing 80 ml of water, and by adding water in small increments. Results indicate that when the water is spilled over the sand-pack, it has the tendency to channel through the sand-pack, significantly reducing the capacity of the dried zone to retain liquid ...

DEFF Research Database (Denmark)

Various MLM-type (M, medium-chain fatty acids; L, long-chain fatty acids) structured triacylglycerols were produced in pilot- or small-scale packed-bed reactors by lipase-catalyzed acidolysis. The incorporation and acyl migration of octanoic acid were measured by gas chromatography and Grignard degradation, and ranged from 39.0 to 48.7% and 0.6 to 9.3%, respectively. Quantitation of triacylglycerol molecular species was performed by ammonia negative ion chemical ionization (NICI) mass spectrometry (MS). The proportion of ACN (acyl carbon number) 34 species that contained one C-18 fatty acid and two C-8:0, in samples analyzed, varied from 12.5 to 23.2%. The selected regioisomers MLM and MML within the ACN 34 species group were quantified by NICI tandem MS (MS/MS) and were in the range of 97.1 to 98.4% and 1.6 to 2.9%, respectively. There was no correlation between the level of acyl migration during lipase-catalyzed esterification and the level of regioisomers of the ...

International Nuclear Information System (INIS)

Pilot-scale pyrolysis units have been in operation since 1980 to test the efficiency of thermal treatment of transuranic (TRU) solid waste to retrieve the TRUs and to reduce the volume of wastes such as spent solvent, spent resin, and others. These wastes are generated by reprocessing, fuel production, and utilities. NUKEM has developed a criticality-safe, ring-slab reactor to decompose solid TRU waste. The plant processes 25 kg/h with a polyvinyl chloride content up to 70%. The overall throughput (inactive) up to the spring of 1982 was 2000 kg. The decontamination factor for the reactor itself is 1000. The liquid wastes, mainly spent solvent, are cracked under nitrogen at 400 to 700"0C in a reactor that is filled by a packed bed kept in motion by a specially designed agitator. This unit was built for 15 kg/h water equivalent evaporation. Up to 1982 the unit processed 2000 kg of spent solvent (simulated) overall. The decontamination factor is ...

International Science & Technology Center (ISTC)

Development of Scientific Foundations of the Technology of the Metal Matrix Packing of Leaky Unreprocessible Spent Nuclear Fuel of Different Purpose Reactors for a Long-term Environmentally Safe Storage.

International Nuclear Information System (INIS)

Since 1988, the Expertise group of Molecular and Cellular Biology (MCB) is an important partner in the development of the Micro-Ecological Life Support System Alternative (MELiSSA). The MELiSSA was designed to allow a small crew to survive on an Antarctic, lunar or Mars outpost, and is a joint research project currently fostered by the European Space Agency, ESA. The MELiSSA functions through a series of five interconnected compartments, of which four are microbial bioreactors and was engineered to degrade organic waste, regenerate the outpost's atmosphere and water, and provide the crew with an additional vegetarian diet. The bioreactor of the third compartment provides the edible cyanobacteria and plants of the fourth compartment with nitrate instead of ammonium as a source of nitrogen. The two bacteria responsible for the biological transformation of ammonium to nitrate (nitrification) are Nitrosomonas europaea and Nitrobacter winogradskyi. Since all MELiSSA-reactors are to be ...

International Nuclear Information System (INIS)

Information is presented concerning solute concentration in a porous layer; solute concentration in a packed crevice; corrosion of a packed carbon steel crevice in NaCl-O"2 solutions; and effect of copper on corrosion in NaCl-O"2 solutions.

UK PubMed Central (United Kingdom)

Animal facilities generate a large amount of used bedding containing excrement as medical waste. We developed a recycling system for used bedding that involves soft hydrothermal processing. In this...Full Text Available

Science.gov (United States)

2.1.1 Levels of preservation and packaging and the levels of packing to be applied selectively are defined in MIL-STD-2073-1 and are mandatory for use or ...

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

A zinc-air battery in a case is described including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit. 7 figures.

Energy Technology Data Exchange (ETDEWEB)

The purpose of this project was to investigate the origin of pressure fluctuations in fluidized bed systems. The study assessed the potential for using pressure fluctuations as an indicator of fluidized bed hydrodynamics in both laboratory scale cold-models and industrial scale boilers. Both bubbling fluidized beds and circulating fluidized beds were evaluated. Testing including both cold-flow models and laboratory and industrial-scale combustors operating at elevated temperatures. The study yielded several conclusions on the relationship of pressure fluctuations and hydrodynamic behavior in fluidized beds. The study revealed the importance of collecting sufficiently long data sets to capture low frequency (on the order of 1 Hz) pressure phenomena in fluidized beds. Past research has tended toward truncated data sets collected with high frequency response ...

Energy Technology Data Exchange (ETDEWEB)

A nitrogen oxides decreasing combustion method comprising: mixing a fuel and air with each other; bringing the mixture obtained into contact with a packed catalyst; and adding a fresh supply of the fuel to the stream obtained to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion, characterized in that only a catalytic reaction or combustion occurs at the packed catalyst; the temperature of the packed catalyst is kept lower than the ignition temperature of the mixture; the adiabatic flame temperature which is reached by the non-catalytic thermal combustion of the mixed gas is lower than the temperature at which the nitrogen oxides occur. 39 figs.

Energy Technology Data Exchange (ETDEWEB)

Ribbon parachute fabrics were tested during development and production of a 24 ft parachute, and after 2.5 years ambient exposure at several storage sites. The effects of sewing, packing, and parachute deployment on material strength were obtained in the 1000 lb Kevlar ribbon after moisture exposure during packing, and when packed parachutes absorbed moisture or were thermal cycled. Individual yarn samples from the low strength ribbons exhibited little change in strength indicating that the material itself had not degraded. Factors leading to the change in ribbon strength are discussed. Considering all materials, there have been no indications to date of any uncontrollable changes in material strength that would limit the use of Kevlar in parachute applications.

Energy Technology Data Exchange (ETDEWEB)

We investigate ordering properties of two-dimensional granular materials using several shapes created by welding ball bearings together. Ordered domains form much more easily in two than in three dimensions, even when configurations lack long-range order. The onset of ordered domains occurs near a packing density of 0.8, a phenomenon observed previously for disks. One of our shapes, the trapezoid, has packings that remain disordered and near the transition density even after annealing by shaking. Although random packings are unstable for disks and many other shapes in two dimensions, trapezoid packings provide an approach to studying two-dimensional randomness. We also find that the rotational symmetry of a shape is an excellent predictor of how easily it orders, and a potential guide to identifying two-dimensional shapes that remain random after annealing.

UK PubMed Central (United Kingdom)

The oxygen production of a photosynthetic gas exchanger containing Chlorella pyrenoidosa (1% packed cell volume) was measured when various concentrations of carbon dioxide were present...Full Text Available

Science.gov (United States)

Purpose: The purpose of this study was to compare nutrient content and cost of home-packed lunches to nutrient standards and prices for reimbursable school lunches. Methods: Researchers observed food and beverage contents of 333 home packed lunches at four north Texas elementary schools. Nutritionist Pro was used to analyze lunches for calories, total fat, saturated fat, protein, fiber, vitamin A, vitamin C, calcium, iron, fiber, and sodium content. These values were then compared to National School Lunch Program (NSLP) standards and other nutrient standards. Cost of each home-packed lunch was estimated based on food prices at three local supermarkets. A one-sample t-test (p = 0.05) was used to compare nutrient values of home packed lunches to National School Lunch Program (NSLP) standards. A paired t-test was used to compare cost of home packed lunches to each school's full price ...

Energy Technology Data Exchange (ETDEWEB)

A method is proposed for operating bed waters in an oil well by injecting silanes into the near-face zone. It is distinguished by the fact that in order to improve the effectiveness of insulation, the silanes used are silanes of general formula Si /SUB n/ H /SUB 2n-n/ .

Energy Technology Data Exchange (ETDEWEB)

This study investigated the effectiveness of dealing with biological waste by composting. In particular, it examined the feasibility of recovering excess thermal energy produced in the process of composting biological waste in terms of mass and energy transport parameters required in the aerated compost bed. An experiment was performed in which a 100 dm{sup 3} adiabatic, leak-tight reactor equipped with a controlled aeration system was constructed to study the temperature and pressure distribution in the bed. Sensors were used to determine the amount and humidity of emitted gases under variable external physical conditions. The perforated bottom of the reactor allowed for bed aeration. As such, the humidity and heat were transported upwards, forced by the air pumped in and by natural convection. In terms of pressure distribution inside the composted and aerated bed, the study results showed that there ...

Scientific Electronic Library Online (English)

Abstract in english A simplified model for drying solids in the constant rate period in a batch fluidised bed was developed.It assumes the bed to be divided into dense and bubble phases with heat and mass transfer between the phases.The model predicts the constant-rate drying period, provided the fluid bed shape and material characteristics are known.The model is compared with experimental data reported in the literature covering a wide range of materials, gas flow rates, column diameters, m (more) aterial hold-ups, air temperatures and humidities.Model predictions compare satisfactorily with the experimental data.

Science.gov (United States)

The Wind Energy Division at Sandia National Laboratories recently completed a point design based on the 34-m Vertical Axis Wind Turbine (VAWT) Test Bed. The 34-m Test Bed research machine incorporates several innovations that improve Darrieus technology, including increased energy production, over previous machines. The point design differs minimally from the Test Bed; but by removing research-related items, its estimated cost is substantially reduced. The point design is a first step towards a Test-Bed-based commercial machine that would be competitive with conventional sources of power in the mid-1990s.

Energy Technology Data Exchange (ETDEWEB)

The concept of a multi-cavity volumetric solar receiver is very attractive for the profitability of certain of its characteristics such as high efficiency and economy. The absorber is based on a pack of small ceramic cavities which intercept and absorb the inherent high solar flux reflected from an array of mirrors. Atmospheric air acts as a coolant medium when it is drawn through the pack. A model for an overall heat transfer performance of the receiver is given and numerically solved.

British Library Electronic Table of Contents (United Kingdom)

Summary Objective Community-based information on the delivery and use of health interventions is important to monitor the effectiveness of the Roll Back Malaria programme. However, community surveys to determine coverage for insecticide-treated bed nets are time-consuming and costly. We wanted to assess whether schoolchildren's reports of household ownership of a bed net and coverage among high-risk groups monitored by schoolteachers through a questionnaire could be used as a proxy of household ownership of bed net and coverage at community level, for routine monitoring of malaria control programmes. Method 3602 schoolchildren in 39 randomly selected schools and 2798 heads of households in 39 villages were interviewed about their use of either insecticide-treated or untreated bed nets. Res...

Science.gov (United States)

The concentration and distribution of a soil fumigant in the subsurface of field plots are two key factors in the determination of the fumigant efficacy. Subsurface concentrations of the biologically active compounds cis- and trans-1,3-dichloropropene (1,3-D) and chloropicrin (CP) were determined in soil at two adjacent injection traces and midpoint between the two traces in plastic-covered field beds after injection of the fumigant Telone C35 by conventional chisels or by a coulter rig (Avenger coulters). Two of the four beds were covered with metallic polyethylene film (MPE) and the remaining two were covered with virtually impermeable film (VIF). Three hours after chisel injection, concentrations of the three compounds at the two adjacent injection traces in the two beds were highly variable. Large concentrations of the compounds were detected at the side traces, whereas the compounds were not detected at the middle ...

British Library Electronic Table of Contents (United Kingdom)

We aimed to investigate the effects of local anesthetics soaked in Merocel nasal packs on hemorrhage and pain after septoplasty. The methodology includes a prospective double-blind study that was conducted in patients undergoing septoplasty because of nasal septal deviation. The study included 143 patients. The patients were divided into four groups. Each group received 1% lidocaine?+?0.000625% adrenalin, 0.375% ropivacaine, 0.25% bupivacaine as study groups or 0.9% sodium chloride as a control group in their Merocel packs postoperatively. The local anesthetics or sodium chloride were reapplied at the eighth postoperative hour. Each patient was given a questionnaire where verbal analog score and amount of postoperative hemorrhage was noted. The statistical analysis was performed using two ...

CERN Document Server

We use X-ray scattering and molecular simulations to investigate the structural properties of complexes of multivalent cationic lipids and DNA molecules. At low mole fraction of neutral lipids (NLs), $\\Phi_{\\rm NL}$, the complexes show dramatic DNA compaction down to essentially close packed DNA arrays with a DNA interaxial spacing $d_{\\rm DNA}=25\\AA$. A gradual increase in $\\Phi_{\\rm NL}$ does not lead to a continuous increase in $d_{\\rm DNA}$ as observed for DNA complexes of monovalent cationic lipids (CLs). Instead, distinct spacing regimes exist, with sharp transitions between them. Three packing states have been identified: (i) close packed, (ii) condensed, but not close packed, with $d_{\\rm DNA}=27-28\\AA$, and (iii) an expanded state, where $d_{\\rm DNA}$ increases gradually with $\\Phi_{\\rm NL}$. Based on our experimental and computational results, we conclude that the DNA condensation ...

International Nuclear Information System (INIS)

Requirements for food packaging materials include whether there is any interaction between the food and the package during or after the irradiation, and whether as a result of the irradiation, volatile or leachable substances are released from the pack into the food. The performance of cellulose-based materials and plastic films under irradiation are discussed.

Energy Technology Data Exchange (ETDEWEB)

One of the important aspects in an absorption system is the effectiveness in which the gas and liquid phases come into contact with each other. An effective absorption process will provide sufficient contacting area for the gas and liquid phases to interact upon. With this in mind, work was conducted to evaluate carbon dioxide (CO{sub 2}) absorption into aqueous solutions of monoethanolamine (MEA) using two different types of contacting devices: gas absorption membrane (GAM) modules and traditional packed columns. The performance of these two absorption devices was compared to one another using the overall mass transfer coefficient (K{sub G}a{sub v}) as a basis. The GAM module contained microporous polypropylene hollow fibre membranes and the packed absorption column contained Sulzer DX structured packing. The results indicate that GAM modules tend to have slightly larger K{sub G}a{sub v} values, potentially opening the ...

Energy Technology Data Exchange (ETDEWEB)

In the atmospheric pressure coal combustion area, the Internally Circulating Fluidized Bed Boiler (ICFB) had already been proven to possess superior performance features in terms of the ease with which load conditions can be controlled and because of its low pollution level. Based on the particular merits of the ICFB furnace and the application of this technology to pressurized fluidized bed boiler technology, it was possible to achieve a pressurized fluidized bed boiler with superior ease of operation, reliability and low-pollution characteristics. From fiscal 1992, the authors have conducted extensive research work, including cold model tests and computer simulations to investigate the possibility of applying ICFB technology to the pressurized fluidized bed boiler technology in an attempt to develop the Pressurized Internally Circulating Fluidized Bed Boiler (PICFB). Based on the ...

Energy Technology Data Exchange (ETDEWEB)

A fluidized bed combustor of 0.146 m diameter and 1 m length was fabricated from stainless steel to burn olive cake. Initially, and in order to obtain fluidization, the system was operated under cold conditions using a sand with particle size in the range of 500 to 710 microns. The continuous combustion experiments were carried out under controlled conditions, such that the effects of bed temperature, olive cake feed rate, fluidization velocity, and particle size on combustion efficiency and flue gas composition were investigated. It was found that the combustion efficiency decreases with the bed temperature, fluidization velocity, and the feed rate, while it increases with the particle size used. Further, the gas products analysis carried out using a gas chromatography analyzer have shown a nonmeasured amount of SO2, and small amounts of CO. Finally, the temperature distribution along the bed indicated ...

Science.gov (United States)

With the help of self-assembly, thermal sintering, selective etching techniques and sol-gel process, the non-close packed (ncp) face-centered cubic (fcc) photonic crystals of titanium dioxide (TiO2) hollow spheres connected by TiO2 cylindrical tubes have been fabricated using silica template. The photonic bandgap calculations indicate that the ncp structure of TiO2 hollow spheres was easier to open the pseudogaps than close packed system at the lowest energy. PMID:17097102

Energy Technology Data Exchange (ETDEWEB)

Development of surface monitoring of the quality of round rubber packing rings for well instruments is discussed. A method is shown for testing the rings under conditions which simulate the operating conditions. A method is proposed for rapid monitoring of the conditions for vulcanization of the rings by the method of determining the ''ring modulus.''

Energy Technology Data Exchange (ETDEWEB)

For light water reactors, loss of coolant is an important point in safety analysis, whereas for gas-cooled reactors the ingress of water into the core region is an incident of safety relevance. The applicability of the computer code system GAMTEREX to pebble beds of spherical high-temperature gas-cooled reactor fuel elements with simulated water ingress is verified by experiment. The measurements were performed at a Siemens-Argonaut reactor, using its ring core as a driver zone for a pebble-bed core in the center of the reactor.

Energy Technology Data Exchange (ETDEWEB)

Direct electric heating by passing an electrical current directly through a bed of adsorbent may prove to be an efficient means of regenerating activated charcoal in continuous and batch adsorption processes. Obvious advantages of this type of regeneration are its almost complete lack of inertia, which makes it possible to reduce the number and dimensions of the adsorbers, and its highly efficient use of energy due to the small number of steps in the conversion of the energy, as well as the reduction of heat losses involved in warming the structure and making up for losses to the surroundings. The authors consider the kinetics of direct electric heating of a stationary bed of activated charcoal not containing adsorbed substances.

Energy Technology Data Exchange (ETDEWEB)

The coal-fired combined cycle with partial gasification and fluidized bed combustion (PGFBC-CC), also referred to as a hybrid cycle, has advantages of staged energy conversion and utilization, which can attain high thermal efficiency with low emissions. Four kinds of PGFBC-CC are studied in this paper, two based on pressurized fluidized bed combustion (PFBC) and two on atmospheric fluidized bed combustion (AFBC). Thermal performance calculations and parametric analyses were performed. On the basis of the results, from the above analyses, the best integration system for China is suggested. In addition, a preliminary exergetic analysis is carried out for three of the PGFBC-CC variants.

UK PubMed Central (United Kingdom)

The objective of this study was to determine the direct actions of nitroprusside and nitroglycerin on the pulmonary vascular bed in the intactchest dog. These widely used nitrogen oxide-containing vasodilator...Full Text Available

Science.gov (United States)

test bed (ADTT) tools technology. Glenn. Research. Center: Aircraft icing training video for regional and cor- porate pilots. Numerical propulsion ...

Science.gov (United States)

... laws between particles (modeling UGV/UAV/UUV collectives) to ... A mobile robot test-bed is used in ... of this work on mobile robots executing pursuit ...

Energy Technology Data Exchange (ETDEWEB)

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period October 1, 2004 through December 31, 2004. The following tasks have been completed. First, the renovation of the new Combustion Laboratory and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building have proceeded well. Second, the detailed design of supporting and hanging structures for the CFBC was completed. Third, the laboratory-scale simulated fluidized-bed facility was modified after completing a series of pretests. The two problems identified during the pretest were solved. Fourth, the carbonization of chicken waste and coal was investigated in a tube furnace and a Thermogravimetric Analyzer (TGA). The experimental results from this study are presented in ...

Science.gov (United States)

Jan 22, 2004 ... Training and Professional Development Leadership Development Program. GSFC Leadership Development Program Positions. Cryo-Optical ...

Energy Technology Data Exchange (ETDEWEB)

The need is substantiated for using remote control of technological processes on blowout dangerous beds. A method is proposed for this control based on recording with the help of AGZ apparatus for gas release into the roadway. Distinguishing features are indicated for the change in methane concentration in the roadway with normal occurrence of the process and in the case of blowout of coal and gas.

Energy Technology Data Exchange (ETDEWEB)

The objective of Phase IV of the contract is to design a conceptual flue gas treating unit based on the fluidized-bed Copper Oxide (FBCO) process for a new coal-fired 500 MW(e) power plant. A technical and economic evaluation of the FBCO process, based on the conceptual design, will also be completed. Progress is described.

Energy Technology Data Exchange (ETDEWEB)

In this paper the possibility of configuring a water cooled Nuclear Thermal Propulsion (NTP) rocket, based on a Particle Bed Reactor (PBR) is investigated. This rocket will be used to operate on water obtained from near earth objects. The conclusions reached in this paper indicate that it is possible to configure a PBR based NTP rocket to operate on water and meet the mission requirements envisioned for it. No insurmountable technology issues have been identified.

British Library Electronic Table of Contents (United Kingdom)

This paper presents the results of experimental investigations of the ignition and combustion of plant biofuels (wood particles, date stones) and products of their mechanical and thermal treatment (pellets, charcoal) at temperatures typical of the burning process in nonforced furnaces and fixed-bed and fluidized-bed gas producers. The influence of the furnace heat treatment of a fuel on its inflammation and combustion has been revealed. The results have been compared with the known data on the burning of pellets, brown coals, and anthracites and with the calculation by the classical diffusion-kinetic model.

Energy Technology Data Exchange (ETDEWEB)

Cattle or chicken manure is pelletized, and a bed of the pellets is combusted at the bottom to create a temperature gradient and to generate a fuel gas. Thus, an approximately 25 cm-high bed of approximately 5 mm-diameter chicken manure pellets was combusted to produce a fuel gas of 1622 kcal/kg manure.

Energy Technology Data Exchange (ETDEWEB)

Background and Purpose: Total-body irradiation (TBI) is an important part of the conditioning regimen for hematopoietic stem cell transplantation (HSCT) in patients with hematologic malignancies. The results after treatment with various TBI regimes were compared, and dose-effect relationships for the endpoints relapse incidence, disease-free survival, treatment-related mortality, and overall survival were derived. The aim was to define requirements for an optimal treatment schedule with respect to leukemic cell kill and late normal-tissue morbidity. Material and Methods: A literature search was performed. Three randomized studies, four studies comparing results of two or three TBI regimens, and nine reports with results of one specific TBI regimen were identified. Biologically effective doses (BEDs) were calculated. The results of the randomized studies and the studies comparing results of two or three TBI regimens were pooled, and the pooled relative risk (RR) was ...

UK PubMed Central (United Kingdom)

In the isolated rat mesenteric bed, the 1 min perfusion with 100 nm anandamide, a concentration that did not evoke vasorelaxation, elicited an acute release of 165.1 ± 9.2 pmol nitric...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Carbonaceous solid material such as coal is gasified in a fast fluidized bed gasification system utilizing dual fluidized beds of hot char. The coal in particulate form is introduced along with oxygen-containing gas and steam into the fast fluidized bed gasification zone of a gasifier assembly wherein the upward superficial gas velocity exceeds about 5.0 ft/sec and temperature is 1500.degree.-1850.degree. F. The resulting effluent gas and substantial char are passed through a primary cyclone separator, from which char solids are returned to the fluidized bed. Gas from the primary cyclone separator is passed to a secondary cyclone separator, from which remaining fine char solids are returned through an injection nozzle together with additional steam and oxygen-containing gas to an oxidation zone located at the bottom of the gasifier, wherein the upward gas velocity ranges from about 3-15 ft/sec and is ...

Energy Technology Data Exchange (ETDEWEB)

The paper reports a work-in-progress outlook of a R and D project aimed at developing an advanced boiler for the combustion of virgin and exhaust olive husks at small scale. Fluidized bed technology has been preferred because of its well known advantages that include large thermal inertia, high combustion efficiency, low NOx emissions and considerable heat transfer rate. A 100 kW atmospheric bubbling fluidized bed combustor has been designed and built. The facility is equipped with devices for continuous fuel feeding as well as heat extraction from the bed region. Measurements of temperature and gas concentrations are obtained by using thermocouples and gas-analyzer. Steady state tests of combustion were carried out at typical fluidized bed combustion temperatures. Tests proved that not only exhaust olive husks but also the virgin ones - with a water content larger than 50% by mass - can be reliably fed ...

International Nuclear Information System (INIS)

We have investigated the diffusion enhancement mechanism of boron-enhanced diffusion (BED), wherein boron diffusivity is enhanced four to five times over the equilibrium diffusivity at 1050 ampersand hthinsp;degree C in the proximity of a silicon layer containing a high boron concentration. It is demonstrated that BED is driven by excess interstitials injected from the high boron concentration layer during annealing. For evaporated layers, BED is observed above a threshold boron concentration between 1% and 10%, though it appears to be closer to 1% for B-implanted layers. For sub-keV B implants above the threshold, BED dominates over the contribution from transient-enhanced diffusion to junction depth. For 0.5 keV B, this threshold implantation dose lies between 3x10"1"4 and 1x10"1"5 cm"-"2. It is proposed that the excess interstitials responsible for BED are produced during the ...

Energy Technology Data Exchange (ETDEWEB)

LEDF (Large Equipment Dismantling Facility) will be constructed for the purpose of decontaminating the high level {alpha} solid waste generated in oarai engineering center of JNC. And, main processing process of LEDF is incineration and melting system. LEDF will be intended to reduce the secondary waste that occurs along with the operation of the off gas processing equipment of incineration and melting system. It assumed that we are able to eliminate the adsorption tower using silica gel, if the decontamination factor to volatile ruthenium is able to expect in the packed scrubber that is established to remove harmful gas. Thereupon, we carried out this tests that eliminates the adsorption tower and reduces the secondary waste. The decontamination factor (DF) to the volatile ruthenium by the water scrubber is confirmed in the established institution which is in Tokai Works. However, decontamination factor differs and depends on the ruthenium concentration, harmful ...

Energy Technology Data Exchange (ETDEWEB)

Theoretical assessment on the chromatographic {sup 99m}Tc generator preparation using (n, {gamma}) {sup 99}Mo produced ex-natural molybdenum was carried out. The relationship between the neutron flux for MoO{sub 3} target activation, Mo-content or Mo adsorption capacity of column packing material, {sup 99m}Tc pertechnetate concentration and/or {sup 99m}Tc radioactivity of eluate was established. The reasonably lower limit of neutron flux of reactor and Molybdenum content of column packing material were found out to estimate the production of portable chromatographic generators available for nuclear medicine application. The concentration of {sup 99m}Tc pertechnetate eluate of low {sup 99m}Tc concentration using the column elution technique was also evaluate theoretically and conducted successfully in practice. Three options of {sup 99m}Tc generator using Titanium-Molybdate, Zirconium-Molybdate and Zirconium Oxide as generator ...

International Nuclear Information System (INIS)

Cobalt-60 gamma radiation has been found to be an effective means of immobilizing stationary phases onto gas and liquid chromatographic supports. The ability of a phase to crosslink was determined to be highly dependent on its chemical structure. Gamma radiation was employed to immobilize Se-30, a methylsilicone, and 216 PS onto Chromosorb WHP for packed column chromatography. The resultant columns exhibited increased thermal stability and a high degree of efficiency. Several blended phases containing varying ratios of Se-30:216 PS were also immobilized onto chromatographic packings. This work was further extended to the immobilization of Se-30 and 216 PS onto fused silica capillaries via gamma radiation. Columns exhibited excellent efficiency and improved thermal stability. An investigation into the role of immobilization of polymeric phases for HPLC was undertaken. Results indicate that gamma radiation can immobilzied polyoctadecylsiloxane ...

Energy Technology Data Exchange (ETDEWEB)

Interbedded limestones and dolomites of the Cambrian Conococheague Formation cropping out northwest of Lancaster exhibit contrasting rheological behavior during deformation. Dolomite beds are uncleaved and form concentric F[sub 1] recumbent folds with hinges trending northeast, parallel to the trend of the Appalachian orogen. Limestone beds show subhorizontal S[sub 1] cleavage with southeast-plunging extension lineations defined by fibrous calcite and ubiquitous smear lineations. In limestone beds, intrafolial F[sub 1] folds with curvilinear hinges are sheath folds flattened in the S[sub 1] cleavage. In zones of most intense shear, F[sub 1] hinges parallel the regional northwest directed tectonic transport direction. In 1969, the author attributed the variation in intrafolial F[sub 1] fold-hinge orientation to hinge-parallel buckling due to constrictional bulk strain. This interpretation, however, is not consistent with the ...

International Nuclear Information System (INIS)

The first part of the study contains a literature compilation of more than 50 original publications reporting the radiation induced effects in 17 different high polymer materials and glass which are relevant in the manufacturing of medical devices or packing materials. The results collected demonstrate that high energy radiation, i.e. gamma- or X-rays, causes various physical and chemical alterations in high polymer materials. A detailed summary and discussion of the results of the original publications is not included in the present report, it will be presented in the second part of the study. Furthermore, the second part of the study will refer to the aspect of wholesomeness of irradiated medical devices or packing materials in a more general manner of representation. (orig.).

International Nuclear Information System (INIS)

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

British Library Electronic Table of Contents (United Kingdom)

Herein, we demonstrate the structure of the PS colloidal crystals which were fabricated on the hydrophilic/hydrophobic Si wafers by a spin-coating technique. Monodisperse PS colloids are spin-coated onto self-assembled monolayers of 3-(aminopropyl)triethoxysilane and propyltrimethoxysilane coated Si wafers. PS spheres organized as ordered close-packed face-centered cubic structure with (111) planes on the hydrophilic surface while they gathered without the crystal structure on the hydrophobic surface. This paper also reports a simple and rapid method to fabricate the close-packed structure of hollow TiO2 spheres. The colloidal crystal of TiO2 hollow spheres was prepared using the PS sphere template on the hydrophobic surface. The mechanism for the growing multilayers of self-assembled PS p...

British Library Electronic Table of Contents (United Kingdom)

The fossil fuel consumption and pollutant emissions in a coal fired fluidized bed boiler could be reduced by biomass pyrolysis gas reburning. The influence of three kinds of biomass pyrolysis gases on the emission of N2O in a laboratory scale fluidized bed was investigated using the mechanism of GRI3.0 in this paper. The results showed that: the effect of sawdust pyrolysis gas reburning on N2O was more significant than that of rice husk and orange peel under the same conditions; the increase of initial oxygen content from 1% to 8% in flue gas would restrain the decomposition of N2O; the N2O decomposition was enhanced by increasing reaction temperature from 1073.15 K to 1323.15 K, and the decomposition rate may reach 99% at 1223.15 K.

International Nuclear Information System (INIS)

Radon concentration in the bed rooms, kitchens, sitting rooms and TV lounges in some houses in the Lahore has been measured using CN-85 Solid State Nuclear Track Detectors in box type dosimeters. Maximum value of radon concentration is 93 Bq/m/sup 3/ in a bed room whereas the minimum value is 25 Bq/m/ sup 3/ in a TV lounge. The average value of radon concentration in bed rooms, kitchens, sitting rooms and TV lounges varies between 43 Bq/m/sup 3/ and 55 Bq/m/sup 3/. Comparison of radon concentration in the old and new houses has been done and no specific relationship has been observed. (author).

Science.gov (United States)

Applying an underfeed system, the underfeed circulating spouted bed was designed as a desulfurization reactor. The main objective of the technology is to improve the mixing effect and distribution uniformity of solid particles, and therefore to advance the desulfurization efficiency and calcium utility. In this article, a series of experimental studies were conducted to investigate the fluidization behavior of the solid-gas two-phase flow in the riser. The results show that the technology can distinctly improve the distribution of gas velocity and particle flux on sections compared with the facefeed style. Analysis of pressure fluctuation signals indicates that the operation parameters have significant influence on the flow field in the reaction bed. The existence of injecting flow near the underfeed nozzle has an evident effect on strengthening the particle mixing.

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the progress made on the development of an integrated multistage fluidized bed retorting process (KENTORT II) during the period of October 1, 1992 through September 30, 1993 under Cooperative Agreement No. DE-FC21-90MC27286 with the Morgantown Energy Technology Center, US Department of Energy. The KENTORT II process includes integral fluidized bed zones for pyrolysis, gasification, and combustion of the oil shale. The purpose of this program is to design and test the KENTORT II process at the 50-lb/hr scale. The PDU was assembled, instrumented and tested during this fiscal year. Along with the major activity of commissioning the 50-lb/hr retort, work was also completed in other areas. Basic studies of the cracking and coking kinetics of model compounds in a fixed bed reactor were continued. Additionally, as part of the effort to investigate niche market applications for KENTORT II-derived products, a ...

UK PubMed Central (United Kingdom)

Refractory ascites can occur in patients with various conditions. Although several procedures based on the reinfusion of ascitic fluid have been reported after the failure of bed rest, salt and water...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Trying to achieve the optimal utilization of oil shale resources, and the production of a more environmentally acceptable fuel, as well as a solid waste with a low a sulphur content, thereby reducing acidic leachates, has led to this investigation. In this article, the influences of the bed temperature and the choice of fluidizing gas on the quality and quantity of the produced fuel gas, using a continuous feed fluidized bed reactor, were investigated. The composition and calorific value of the generated gas were determined. There was a nearly linear increase in the amount of fuel gas produced as a function of temperature, reaching {approx}350 kg per 10{sup 3} kg of dry raw shale and the gross calorific value ranged from 15 to 23 MJ-kg{sup -1} with CO and H{sub 2} being the major constituents. Subsequent experiments were carried out, employing a thermogravimetric analyser under similar conditions as applied to the fluidized ...

Energy Technology Data Exchange (ETDEWEB)

The technology being evaluated is the Modified In-Situ (MIS) retorting process for raw shale oil production, combined with a Circulating Fluidized Bed Combustor (CFBC), for the recovery of energy from the mined shale. (VC)

Energy Technology Data Exchange (ETDEWEB)

This article puts the case for coal fired combined cycle gas turbine (CCGT) power plants. The need to gasify the coal for the CCGT, use of fluidised bed combustors or gasification systems, the difference in prices of coal and natural gas, and coal and natural gas reserves are discussed. (UK)

UK PubMed Central (United Kingdom)

Outpatient practice after percutaneous coronary intervention (PCI) is gaining momentum due to constantly optimizing results. Furthermore, the availability of limited beds to handle the large volume...Full Text Available

UK PubMed Central (United Kingdom)

Anaerobic treatment of a volatile fatty acid (VFA) mixture was investigated under psychrophilic (3 to 8°C) conditions in two laboratory-scale expanded granular sludge bed reactor stages in series....Full Text Available

UK PubMed Central (United Kingdom)

Thermophilic propionate-oxidizing, proton-reducing bacteria were enriched from the granular methanogenic sludge of a bench-scale upflow anaerobic sludge bed reactor operated at 55°C with a mixture...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report is to present the progress made on the project ''Establishment of an Environmental Control Technology Laboratory (ECTL) with a Circulating Fluidized-Bed Combustion (CFBC) System'' during the period January 1, 2005 through March 31, 2005. The following tasks have been completed. First, the renovation of the new Combustion Laboratory is nearly complete, and the construction of the Circulating Fluidized-Bed (CFB) Combustor Building is in the final stages. Second, the fabrication and manufacture of the CFBC Facility is being discussed with a potential contractor. Discussions with potential contactor regarding the availability of materials and current machining capabilities have resulted in the modification of the original designs. The selection of the fabrication contractor for the CFBC Facility is expected during the next quarter. Third, co-firing experiments conducted with coal and chicken waste ...

UK PubMed Central (United Kingdom)

The sensitivities to cefuroxime and cephradine of potentially pathogenic bacteria isolated in two British general hospitals comprising 900 beds have been assessed. In a three-month period 2537 strains...Full Text Available

UK PubMed Central (United Kingdom)

Most hospitals today are quickly developing special programs and services that are designed to compete for physicians and patients, and ultimately fill unoccupied beds. In an attempt to attract physicians...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Describes the wastes produced and the waste disposal methods used at BEWAG power plants. Wastes covered include fly ash, fluidized bed ash, gypsum from flue gas desulfurization and evaporation residues. Disposal methods include using ashes and gypsum to make building materials. Despite many years of experience in the utilization and disposal of residues from coal-fired power stations BEWAG have not encountered any disposal problems. 5 tabs.

International Nuclear Information System (INIS)

Three dimensional temperature field and helium flow field of TBM are simulated using the general purpose computational fluid dynamics (CFD) code FLUENT. The temperature distribution of Be Armor, Be Pebble Bed, Li_4SiO_4 Pebble Bed, Structure Material of TBM, and helium flow field in the cooling pipe are presented. The research indicates that the work temperature of each material is under the material temperature allowed except some places where high temperature should be excluded in the design. The results will provide references for further optimized thermal hydraulic design of ITER China TBM. (authors)

Energy Technology Data Exchange (ETDEWEB)

System-level-operational testing of the ETX-II test-bed electric vehicle is described and the results discussed. Because the traction battery is a major factor in the performance of an electric vehicle, previously reported work on the sodium-sulfur battery designed for use with the ETX-II is reviewed in detail. Chassis dynamometer performance of the test-bed vehicle met or exceeded design goals and compared reasonably well with SIMPLEV computer modeling results. Areas are identified wherein further work is needed to establish a firmer basis for comparison of the simulation and the observed results.

International Nuclear Information System (INIS)

Processes of production and purification (necessary for fabricating fuel elements) of powdery uranium dioxide with particle size up to 1000 #mu#m and more have been studied. Developed is continuous process of UO_2 production with above particle size by converting uranium hexafloride into UO_2 solid particles in fluidized bed while their interaction with water vapor and hydrogen on the uranium dioxide nucleus material. The method allows to conduct continuous selection from the apparatus of UO_2 powder fraction with particle size near 1000 #mu#m without nucleus material additional feed.

Energy Technology Data Exchange (ETDEWEB)

Diffusion of radon in a bed of activated charcoal is described by diffusion equations. An analytical solution of these equations is presented for the case of constant radon concentration in the atmosphere. The solutions are given separately for short term and long term exposure. An analytical form of the calibration constant f for long term exposure and constant radon concentration in air, was found. A numerical method and computer code based on the method of finite elements is developed for the case of variable radon concentration in air. This program simulates radon adsorption by the activated charcoal bed, enabling determination of sensitivity. The dependence of sensitivity on different parameters, such as temperature, thickness of the charcoal, etc. was studied using this program. (orig.) 10 refs.

Energy Technology Data Exchange (ETDEWEB)

This book includes the latest developments and covers pump performance, selection and operations, materials, seals and packings, effective fluid characteristics, filtration, piping systems, economics, valves, instrumentation, automatic controls, power transmission equipment, pump and pipeline heating, and more. An extensive data section contains formulas, charts, symbols, nomographs, and standard specification documents.

UK PubMed Central (United Kingdom)

Phthalate esters (PE's) are plasticizers used to soften PVC-based medical devices. PE's are the most abundant man-made pollutants and increase the risk of developing an allergic respiratory disease...Full Text Available

Wastenet

...Butley river and Ore estuary, Boyton Marshes attracts breeding wading birds in spring and ducks, geese and swans in winter. It's also ...The spectacular cliffs at Fowlsheugh are packed with 130,000 breeding seabirds in the spring and summer, including guillemots, razorbills and kittiwakes. Freiston ...for its breeding avocets and terns, which can be seen throughout the spring and summer. Access is by boat only and the trip ... During spring and autumn, it is an ideal place to see migrant wading birds, gulls and terns. Leighton Moss Leighton ...

Energy Technology Data Exchange (ETDEWEB)

In studying the absorption of carbon dioxide by absorbents impregnated with alkanol amines, researchers used a laboratory-scale packed column to determine the overall gas-phase mass-transfer coefficients and enhancement factors. A model derived for the mechanism of the chemical reaction taking place in the interfacial layer accounts for the effect of the reaction upon the absorption rate better than other models.

Science.gov (United States)

In this paper, we evaluate the performance of the 1- and 5-site models of methane on the description of adsorption on graphite surfaces and in graphitic slit pores. These models have been known to perform well in the description of the fluid-phase behavior and vapor-liquid equilibria. Their performance in adsorption is evaluated in this work for nonporous graphitized thermal carbon black, and simulation results are compared with the experimental data of Avgul and Kiselev (Chemistry and Physics of Carbon; Dekker: New York, 1970; Vol. 6, p 1). On this nonporous surface, it is found that these models perform as well on isotherms at various temperatures as they do on the experimental isosteric heat for adsorption on a graphite surface. They are then tested for their performance in predicting the adsorption isotherms in graphitic slit pores, in which we would like to explore the effect of confinement on the molecule packing. Pore widths of 10 and 20 A are chosen in this ...

Energy Technology Data Exchange (ETDEWEB)

The main purposes of this research was to investigate the feasibility of incineration of wool-scouring sludge in a novel vertical-axis-rotating fluidised bed (RFB). The experiment was carried out in a RFB with an internal diameter (ID) of 200 mm and height of 50 mm. A cold test was first conducted to investigate the fluidization performance of the RFB via parameters such as the bubbling, gas distribution, bed shape and pressure drop. The tumbling phenomena was observed in the bed, and this effectively enhanced the axial mixing. The appropriate range of bed thickness, rotating speed and sand particle size were identified to ensure the full fluidization and reduce the particle elutriation. Four wool-scouring sludges from different processes were incinerated in the RFB. With 5% support methane, all sludges with a maximum moisture up to 70% as received could be successfully burned in the RFB at rotating ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of this program are to evaluate the Coal Fired Combined Cycle (CFCC) power plant conceptual design and to conduct supporting development programs for pressurized fluidized bed technology advancement in combustion/steam generator, gas turbine and hot gas cleanup technologies. The Coal-Fired Combined Cycle is the unique power plant concept developed under the leadership of the General Electric Company to provide a direct coal-burning gas turbine and steam turbine combined-cycle power plant. The advantages of the combined cycle for higher efficiency and the potential of the pressurized fluidized bed combustor improvements in emissions could offer a new and attractive option to the electric utility industry. The CFCC approach provides for cooling the fluid bed combustor through the use of steam tubes in the bed which supply a steam turbine generator. The partially cooled combustion gases ...

Energy Technology Data Exchange (ETDEWEB)

Progress reports are presented for the following two areas: catalytic cracking studies with water-wet silica-alumina catalysts; and Fischer-Tropsch reactor studies where similarities and differences between fixed bed and slurry type reactors are investigated and further experiments conducted to measure mass transfer coefficients and reaction kinetics which are to be used in a model slurry reactor. The following are some of the conclusions. (1) The premise that the presence of liquid water might increase catalytic cracking activity was found to be invalid. It was demonstrated that cracking can occur at previously unobserved low temperatures (though at low conversions) and that an anomaly exists in that one of the catalysts tested shows an entirely different cracking behavior and probably follows a different cracking mechanism. (2) the diameter of a fixed-bed Fischer-Tropsch reactor critically affected the resistance of the reactor to plugging ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the effects of SiC coating on the oxidation resistance of C/C composites in combusting fields, which are expected to be applied to high temperature structural materials at over 1770K. The coating methods employed were CVD and pack cementation. The time changes in weight loss of the specimens were measured at temperatures of 1770K and 1900K under the equivalence ratio of 0.9 generated by methane-air combustion, and the surface of the specimens before and after the experiment was observed by SEM. Although the weight loss of the specimens coated by the CVD method was minimal, the coating layer was easily peeled off from the substrate. On the other hand, the layer of the specimens coated by the pack cementation method was stable and adhered to the substrate, but the substrate was degraded because of penetration of oxygen through the pores in the layer. To cover the pores, the specimens were additionally coated with glass ...

Energy Technology Data Exchange (ETDEWEB)

Power plants generate a great amount of ash during coal combustion. From this process two different kinds of ashes are extracted: fly ash (FA) and bottom ash (BA). In this work possible use of both fly and bottom ash as raw material for the ceramic industry is analyzed. The samples were formed by mechanical mixing of both kinds of ashes, and density evolution during conformation as structural ceramic (packing, pressing and sintering) was studied. It was verified that powders with larger fly ash content exhibited higher packing density resulting in compacts with improved green and sintered densities. Preheating treatments at temperatures above 600{sup o}C also increased the green and sintered densities. Dilatometric curves on compacts formed from FA and BA powders were run at constant heating rate and at isothermal cycles. From the analysis of these data it can be established that liquid-phase sintering is the densification mechanism present at ...

International Nuclear Information System (INIS)

The objective of this report was to evaluate four possible alternative methods of preparing and packaging spent fuel assemblies for geologic disposal against the Reference Process of unmodified spent fuel. The four alternative processes were: (1) End fitting removal, (2) Fission gas venting and resealing, (3) Fuel bundle disassembly and close packing of fuel pins, and (4) Fuel shearing and immobilization. Systems analysis was used to develop a basis of comparison of the alternatives. Conceptual processes and facility layouts were devised for each of the alternatives, based on technology deemed feasible for the purpose. Assessments were made of 15 principal attributes from the technical, operational, safety/risk, and economic considerations related to each of the alternatives, including both the surface packaging and underground repository operations. Specific attributes of the alternative processes were evaluated by assigning a number for each that expressed its ...

Energy Technology Data Exchange (ETDEWEB)

Human beings are confronted with another grievous disaster - coal fire. The monitoring on underground coal bed combustion relied on drilling supervising in the past, but this method is not good. By taking the coal fire of Gulaben mine in Inner Mongolia Autonomous Region as an example, the monitoring methods of underground coal bed combustion were explored based on the hyperspectra and high-resolution remote sensing technology. By employing the OMIS imaging apparatus developed by Shanghai Institute of Technical Physics of Chinese Academy of Sciences, the airborne hyperspectral images and the characteristic spectra of different types were obtained and the temperature was measured synchronously on the ground. Then according to the correlation of DN value of the thermal infrared band and surface temperature, the image information was processed, the spectral features were analyzed, and the surface temperature retrieval model was built. Finally, by ...

Energy Technology Data Exchange (ETDEWEB)

This work presents comparative results of a numerical investigation of four possible models for the prediction of thermal performance of fixed bed storage units and their thermal design. These models includes Schumann's model, the radial dispersion model, a model that include both axial heat conduction in the fluid phase and admits thermal gradient in the solids particles and finally a two dimensional single phase model. For each of these models a computer code was written and tested to evaluate the computing time of same data and analyze any other computational problems. The tests of thermal performance included particle size, porosity, particle material, flow rate, inlet temperature and heat losses form tank walls and extremities. Dynamics behaviour of the storage units due to transient variation in either flow rate or inlet temperature was also investigated. The results presented include temperature gradients, pressure drop and heat storage. The results ...

Energy Technology Data Exchange (ETDEWEB)

This work reports an experimental study on the steam gasification of an anthracite coke in a fluidized bed reactor, with the aim of evaluating the reaction kinetics. Isothermal runs were carried out with samples of 91 to 275 g of coke, at temperatures between 799 and 928{sup 0}C and for steam partial pressures between 0.3 and 0.9 atm. The conversion decreases as the amount of coke is increased and it is very sensitive to the temperature. Neither the volumetric reaction model nor the unreacted shrinking core model can satisfactorily fit the experimental results. That is why empirical models have been used. The first one is derived from the unreacted shrinking core model. An activation energy of 219 kJ. mol{sup -1} and a reaction order with respect of steam of 0.57 have been identified. In the second model, the conversion has been correlated as a function of a dimensionless time. A comparison of the results obtained in the fluidized bed with ...

International Nuclear Information System (INIS)

During the water detritiation process most of the tritium inventory is transferred from water into the gaseous phase, then it is further enriched and finally extracted and safely stored. The control of tritium inventory is an acute issue from several points of view: - Financially - tritium is an expensive material; - Safeguard - tritium is considered as nuclear material of strategic importance; - Safety - tritium is a radioactive material: requirements for documented safety analysis report (to ensure strict limits on the total tritium allowed) and for evaluation of accident consequences associated with that inventory. Large amounts of tritium can be stored, in a very safely manner, as metal tritides. A bench-scale experiment of a tritium storage bed with integrated system for in-situ tritium inventory accountancy was designed and developed at ICSI Rm. Valcea. The calibration curve and the detection limit for this experimental model of tritium storage ...

Energy Technology Data Exchange (ETDEWEB)

In the future fossil fuelled power plants are realised/laid down as combined cycle power plants with high current generation efficiencies. The method of pressure fluidized-bed combustion with downstream hot gas cleaning is going to compete with methods combined with a pressure coal gasification or a pressure dust combustion. The advantages of the pressure fluidized bed combustion are the simpler method set-up and consequently lower investment costs. (orig./CD) [Deutsch] Kohlegefeuerte Kraftwerke werden zukuenftig als kombinierte Gas/Dampfturbinen-Kraftwerke mit hohen Stromerzeugungswirkungsgraden ausgefuehrt werden. Das Verfahren der Druckwirbelschichtverbrennung mit nachgeschalteter Heissgasreinigung und Rauchgasturbine wird dabei mit Verfahren mit einer vorgeschalteten Kohledruckvergasung oder mit einer Druckstaubfeuerung konkurrieren. Die Vorteile der Druckwirbelschichtverbrennung liegen dabei auf dem insgesamt einfacheren Verfahrensaufbau ...

Energy Technology Data Exchange (ETDEWEB)

Experimental and theoretical investigation on drying of a single coal particle in fluidized bed combustor is presented. Coal particle drying was considered via the moist shrinking core mechanism. The results of the drying test runs of low-rank Serbian coals were used for experimental verification of the model. The temperature of the coal particle center was measured, assuming that drying was completed when the temperature equalled 100{sup o}C. The influence of different parameters (thermal conductivity and specific heat capacity of coal, fluidized bed temperature, moisture content and superheating of steam) on drying time and temperature profile within the coal particle was analyzed by a parametric analysis. The experimentally obtained results confirmed that the moist shrinking core mechanism can be applied for the mathematical description of a coal particle drying, while dependence between drying time and coal particle radius, a square law ...

Energy Technology Data Exchange (ETDEWEB)

A study of two forest areas in India investigated how much energy is wasted when high stumps are left after trees are cut to produce wooden boxes for packing the apple harvest. Measurements of the stumps determined the total wood pulp wasted, which was 1191 tons during 1981. The calorific value of the stumps would supply a year's cooking and heating fuels for 747 families of five. Additional fuel is wasted by abandoning the branches and tree tops which are unsuitable for box construction. 5 references, 4 tables.

Energy Technology Data Exchange (ETDEWEB)

New technologies make multi-megajoule glass lasers economically feasible. Laser architectures using harmonic switchout, target plane holographic injection, phase conjugation, continuous apodization and higher amplifier efficiencies have been devised. A plan for a multi-megajoule laser which can be built for an acceptable cost relies on manufacturing economies of scale and the demonstration of the new technologies presented here. These include continuous pour glass production, rapid harmonic crystal growth, switching of large blocks of power using larger capcaitors packed more economically and by using large identical parts counts.

International Nuclear Information System (INIS)

The author describes feasibility study on the scheme of disposing spent guide tubes at Daya Bay nuclear power plant, including scheme selection, packing cask design, disposal operation and technological process, budget estimation and safety evaluation. The research results show that the new scheme is feasible on technology, and reasonable on budget. If the scheme is adopted to dispose the spent guide tubes at Daya Bay nuclear power station, it can not only save large funds, but also accumulate experience on disposing non-compressible low and intermediate level solid radioactive wastes produced at nuclear power station for the country

Energy Technology Data Exchange (ETDEWEB)

A packed column was used for investigating the desorption rate of CO{sub 2} from aqueous methyldiethanolamine (MDEA) and activated MDEA solutions. Experiments were conducted within the temperature range 30--70 C, the concentration of MDEA was 4.28 kmol/m{sup 3}, and the concentration of piperazine (PZ) was 0.10 kmol/m{sup 3} for aqueous activated MDEA solutions. Experimental data confirmed that the kinetics model of absorption CO{sub 2} into aqueous MDEA and activated MDEA solutions can be applicable to the situations in which desorption occurs, and the desorption rate of model predictions agree well with that of experimental determination.

Wastenet

... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions Microchemical Engineer... Provides the information chemists and engineers need to evaluate the use of microreactors, covering the technical, operational, and economic considerations for various applications. AU$136.36 ex-GST Terms and Conditions Perry's Chemical Engin... Was: $199.95 inc gst NOW: $129.95 Special Price ...

Wastenet

... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions CRC Handbook of Chemis... For almost a century this handbook has been updated annually, except for a few wartime years, and has served generations of engineers and scientists. Current daily price AU$209.09 ex-GST Terms and Conditions Perry's Chemical Engin... Was: $199.95 inc gst NOW: ...

Energy Technology Data Exchange (ETDEWEB)

Electric and hybrid-electric vehicles are being developed and commercialized around the world at a rate never before seen. These efforts are driven by the prospect of vehicles with lower emissions and higher fuel efficiencies. The widespread adaptation of such vehicles promises a cleaner environment and a reduction in the rate of accumulation of greenhouse gases, Critical to the success of this technology is the use of electrochemical power sources such as batteries and fuel cells, which can convert chemical energy to electrical energy more efficiently and quietly than internal combustion engines. This overview will concentrate on the work being conducted in the US to develop advanced propulsion systems for the electric and hybrid vehicles, This work is spearheaded by the US Advanced Battery Consortium (USABC) for electric vehicles and the Partnership for a New Generation of Vehicle (PNGV) for hybrid-electric vehicles, both of which can be read about on the world wide web ...

Energy Technology Data Exchange (ETDEWEB)

Cassava is cultivated almost all over the world and it is considered one of the most important nutritious sources of calories in the human diet. Cassava is a viable food against starvation in several poor areas of the world because it is an extremely resistant culture and may reach satisfactory economical yield. We utilized vacuum packed industrialized cassava irradiated with 0,1 kGy, 3kGy and 5kGy and stored under refrigeration for 1, 21, 30 and 50 days. Our objective was to analyse the synergistic effect of vacuum packing, irradiation and refrigeration on the preservation of minimally processed cassava. The samples were analyzed for pH, acidity, weight, humidity, texture and color. The irradiation did not affect the chemical characteristics of the cassava. Neither the pH nor the acidity, the most relevant variables to verify deterioration in cassava, presented significant alterations during the period of storage. Comparing the irradiated ...

International Nuclear Information System (INIS)

The evaluation methodology utilized in deciding to change over Oyster Creek plant operation from chemical regeneration of condensate demineralizer resin beds to throwaway of this spent resin is presented. Both the economic and operational aspects considered are discussed. The evaluation shows that potential savings in the $1.1M range are feasible over a 5 year cycle. Cost sensitivity analysis results define the throwaway versus regeneration breakeven point to be 47 condensate demineralization beds per 5 year cycle. The evaluation also discusses the trade off between resin and evaporator concentrates burial volumes. Analyses are given which show that the burial volume cost equivalency of resin to solidified concentrates is 150 ft./sup 3/ of resin equals 400 ft./sup 3/ of concentrates. Based on one year of power operation in the throwaway mode, the savings and operational value anticipated in the initial study are being realized.

Energy Technology Data Exchange (ETDEWEB)

Two cases of tetracycline ulcers of the oesophagus are reported and compared with thirteen other cases from the literature. In most cases, the patients had taken their capsules with little or no fluid just before going to bed. Some hours later they developed retrosternal pain that was intensified by swallowing. Endoscopy showed sharply demarcated greyish-white areas of mucosal damage which represented layers of stratified squamous cells, separated by oedema, and a dense neutrophilic infiltration of the lamina propria and the muscularis mucosa. Roentgenology was unsuitable to detect the lesions. They healed without complications within one to six weeks. Prolonged retention of the capsules in the oesophagus is thought to cause the mucosal damage. Patients on oral tetracycline or doxycycline treatment should therefore be instructed to take their capsules with a meal or with copious water and not just before going to bed.

British Library Electronic Table of Contents (United Kingdom)

In vulnerable individuals, exposure to stressors can result in chronic disorders such as generalized anxiety disorder (GAD), major depressive disorder (MDD), and post-traumatic stress disorder (PTSD). The extended amygdala is critically implicated in mediating acute and chronic stress responsivity and anxiety-like behaviors. The bed nucleus of the stria terminalis (BNST), a subregion of the extended amygdala, serves as a relay of corticolimbic information to the paraventricular nucleus of the hypothalamus (PVN) to directly influence the stress response. To investigate the influence of the corticosteroid milieu and housing conditions on BNST function, adult C57Bl/6J were either acutely or chronically administered corticosterone (CORT, 25mg/kg in sesame oil) or vehicle (sesame oil) or were g...

Science.gov (United States)

In this paper Particle Bed Reactor (PBR) designs are discussed which use /sup 233/U and /sup 242m/Am as fissile materials. A constant total power of 100MW is assumed for all reactors in this study. Three broad aspects of these reactors is discussed. First, possible reactor designs are developed, second physics calculations are outlined and discussed and third mass estimates of the various candidates reactors are made. It is concluded that reactors with a specific mass of 1 kg/MW can be envisioned of /sup 233/U is used and approximately a quarter of this value can be achieved if /sup 242m/Am is used. If this power level is increased by increasing the power density lower specific mass values are achievable. The limit will be determined by uncertainties in the thermal-hydraulic analysis. 5 refs., 5 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

Formulas were developed based on an aqueous solution of hydrolyzed polyacrylonitrile widely used in the oil industry. The additive used consisted of products of industrial production: synthetic resin TEG-1 with hardening agent PEPA (polyehtylene polyamine) and technical formalin. The mixtures containing about 80-85% by volume 5% hydrolyzed polyacrylonitrile, 10-15% by volume of resin TEG-1 with hardening agent PEPA and 3-5% by volume formalin satisfy the requirements made for the plugging materials. The initial mixtures are distinguished by technological efficiency of preparation and have controllable hardening periods. Physical-chemical properties are given for the gel polymers. In the set of properties, the mixtures based on hydrolyzed polyacrylonitrile, resin TEG-1 with hardening agent PEPA and formalin can be recommended as plugging materials of temporary action with complex treatment of the heterogeneous beds.

Energy Technology Data Exchange (ETDEWEB)

An emergency shutdown system for high-temperature gas-cooled pebble-bed reactors is proposed in addition to the common absorber rod shutdown system. This system is based on the strongly absorbing effect of small boronated graphite spheres (called KLAK), which trickle in case of emergency by gravity from the top reflector into the reactor core. The inner reflector of the Siemens-Argonaut reactor was substituted by an assembly of spherical Arbeitsgemeinschaft Versuchsreaktor fuel elements, and the shutdown effect was examined by installing well-defined KLAK nests inside this assembly. The purpose was to develop and prove a calculational procedure for determining criticality values for assemblies of large fuel spheres and small absorbing spheres.

Energy Technology Data Exchange (ETDEWEB)

The article profiles developments in pollution control resulting from the strict emissions control standards due to be set by the European Commission in 1992. In particular technology to meet new emissions targets for mercury and dioxins is described. Control technologies covered included fixed-bed, direct injection, circulating fluidized bed and spray adsorption all of which use activated charcoal to absorb dioxin and mercury. Unfortunately activated charcoal processes still leave waste to be disposed of. Options include recycling the spent activated charcoal to the incinerator, vitrifying the activated charcoal and fly ash into a glassy unleachable substance and cracking the dioxins catalytically. It is hoped the developments will increase public acceptance of incineration. 4 figs., 1 tabs.

Energy Technology Data Exchange (ETDEWEB)

Operation and maintenance cost estimating methodologies for advanced coal-fired atmospheric circulating fluidized-bed and advanced natural gas-fired combined cycle electric power plants are presented. The purpose of these cost estimating relationships is for use in long range planning and evaluation of the economics of use of these technologies for electric power generation. Projected annual costs of reference plants at ten different sites in the United States, one in each of the ten DOE regions, are given as of 1989, and comparisons are made with existing technologies. A listing of a computer program implementing the methodologies is included. 14 refs., 4 figs., 13 tabs.

British Library Electronic Table of Contents (United Kingdom)

Fur die Trennung binarer Gemische wird zunehmend das Simulated Moving Bed (SMB)-Verfahren verwendet. Fur einen storungsfreien Betrieb mussen die Volumenstrome sowie die Umschaltzeit exakt eingestellt werden. In diesem Beitrag wird mit Hilfe des Coherence-Konzepts eine Methode aufgezeigt, mit der sich die Stellgroen fur einen dispersionsfreien SMB-Prozess bestimmen lassen. Fur Langmuir- und Anti-Langmuir-Isotherme konnen einfache explizite Gleichungen bei vollstandiger Trennung angegeben werden. Das Grundprinzip dieser Methode lasst sich auch auf andere Isotherme sowie fur die unvollstandige Trennung ubertragen.

Energy Technology Data Exchange (ETDEWEB)

The moment analysis of pulse responses was applied to a biological activated carbon (BAC) bed to evaluate the microbial activity. Glucose and activated carbon fiber (ACF) were employed in experiments as a model tracer and an activated carbon respectively. No significant difference in biodegradation rates of glucose by microorganisms attached on different solid supports such as activated carbon inactivated carbon and glass fibers was observed. However, higher microbial activity was obtained from microorganisms supported on the ACF in terms of the apparent degradation of total organic including metabolic byproducts by microorganisms, since part of the metabolic byproducts was irreversibly deposited onto the ACF. 11 refs., 6 figs.

Energy Technology Data Exchange (ETDEWEB)

Both the KRW fluidized-bed gasifier and the transport gasifier case studies were used for this assessment. The transport technology is a high-velocity circulating fluidized-bed reactor currently under development by The M.W. Kellogg Company. In the earlier assessment, seven design concepts or cases were identified; a process design was developed; major equipment items were identified; estimates of capital cost, operation and maintenance cost, and cost of electricity were developed; reliability was predicted; and development issues were identified for six studies. Three of the most probable cases were further evaluated for a Greenfield assessment in this report to adequately determine all costs independent of facilities at Plant Wansley.

British Library Electronic Table of Contents (United Kingdom)

Abstract Aims: To develop an in vitro flat-bed perfusion biofilm model that could be used to determine the antimicrobial efficacy of topically applied treatments. Methods and Results: Pseudomonas aeruginosa and Staphylococcus aureus biofilms were grown within continuously perfused cellulose matrices. Enumeration of the biofilm density and eluate was performed at various sampling times, enabling determination of the biofilm growth rate. Two antimicrobial wound dressings were applied to the surface of mature biofilms and periodically sampled. To enable real-time imaging of biofilm growth and potential antimicrobial kinetics, a bioluminescent Ps. aeruginosa biofilm was monitored using low-light photometry. Target species produced reproducible steady-state biofilms at a density of c. 107 per b...

Energy Technology Data Exchange (ETDEWEB)

The present invention provides an improvement in the art of combined steam turbine and gas turbine power plants of the type wherein the principal source of energy is a fluidized bed combustor fueled by coal. More specifically, the invention pertains to supplemental firing of the gas turbine cycle with a clean hydrocarbon fuel (CHF) at a high incremental efficiency to significantly increase overall plant efficiency.

Science.gov (United States)

A steam producing system based on fluidized-bed gasification of biomass materials is discussed. Limited experimental results are discussed and show that steam has been produced at rates of 334.3 kg/hr. (737 lbs/hr.) with 2.8 kg of stream produced for each kilogram of cotton gin trash (2.8 lb/lb.). ref.

Energy Technology Data Exchange (ETDEWEB)

A final report is presented on the design, environmental characteristics, performance and maintainability, and economic analysis of a commercial 663 MWe coal-fired combined cycle power plant using pressurized fluidized bed combustion, and advanced technology in the hot gas cleanup system and gas turbines. Experimental data on the performance of each of the major components are included. (LCL)

Energy Technology Data Exchange (ETDEWEB)

This document contains the outline and viewgraphs used in the speech. Topics covered are: conventional oil and gas recovery; unconventional oil and gas sources; oil shale resources; conventional coal combustion; advanced fossil power systems; fluidized bed combustion; coal/oil or coal/water mixtures; and gaseous and liquid fuels from coal. (DMC)

Energy Technology Data Exchange (ETDEWEB)

The invention deals with an offshore drilling or production platform in particular designed for quake-active areas. The platform rests on the sea bed with a low-gravitational weight and anchored to stabilized pile foundations absorbing the horizontal and vertical acting forces from earthquakes. The platform including pillars can be made of different materials, prestressed concrete in particular. 3 figs.

Energy Technology Data Exchange (ETDEWEB)

The objective of this project is to develop a pellet formulation which is capable of achieving low sulfur partial pressures and a high capacity for sulfur, loaded from a hot fuel gas and which is readily regenerable. Furthermore the pellet must be strong for potential use in a fluidized bed and regenerable over many cycles of loading and regeneration. Regeneration should be in air or oxygen-depleted air to produce a high-concentration sulfur dioxide. Fixed-bed tests were conducted with several formulations of manganese sesquioxide and titania, and alumina They were subject to a simplified fuel gas of the oxygen-blown Shell type spiked with a 30,000ppmv concentration of H{sub 2}S. Pellet crush strengths for 4 and 2mm diameter pellets was typically 12 lbs per pellet and 4 lbs per pellet, respectively. For the most favorable of the formulations tested and under the criteria of break-through at less than 100ppmv H2S and loading temperatures of ...

International Nuclear Information System (INIS)

In the case of a release of residual power and fragmenting following a hypothetical accident the applied powers are small. The boiling in the fluid in the bed promotes leveling and the angles of repose obtained are very small. For a specific power in water of 3.1 W/cm_3 a limiting angle of repose of less than 2 degrees is obtained after a time interval of between 1 and 3 hours. EDULCOREE-and ETABUL-research programs are carried out. (DG).

Energy Technology Data Exchange (ETDEWEB)

Using an experimental pilot plant, designed and built for the tests, the influence of the following parameters was determined: desulphurization of the test gas, temperature, residence time in the reactor tube, concentration of the hydrogen sulphide and desulphurization agent, size of the particles which comprise the agent and composition of the gas. Allowance was made for the effect of calcination and carbonisation. Desulphurization was carried out with limestone on a gaseous mixture of CO and H/sub 2/. A mathematical description of the test findings and yield is presented. 8 refs.

Energy Technology Data Exchange (ETDEWEB)

Restructuring was carried out on a sedimentary basin structure model of the Osaka plain including Osaka Bay by using newly obtained underground structural data. After the Hygoken-nanbu Earthquake of 1995, a large number of underground structure investigations have been performed in Osaka Bay and urban areas of Kobe and Osaka. However, very few surveys have been done in areas peripheral to Osaka Prefecture, such as the Ikoma area. Therefore, an attempt has been made to increase the number of measuring points to acquire underground structural data of these areas. Estimation of basic rock depths has utilized the dominant cycles in H/V spectra obtained from micro vibration survey, and good correlation of the base rock depths derived by a refraction exploration and a deep-bed boring investigation. With regard to bed division and P- and S- wave velocities in sedimentary beds in the Osaka sedimentary basin, an underground ...

Energy Technology Data Exchange (ETDEWEB)

The use of pressurised fluidized-bed coal combustion (fbc) in a combined cycle is seen as a most attractive technology for increasing the efficiency of electricity generation. The concept of pressurised fbc is described and the technical problems that are encountered in its operation and in limiting it to a gas turbine are discussed. Details are given of pilot plant facilities and current R and D programmes.

International Nuclear Information System (INIS)

In this review, we demonstrate the developmental appearance, structural features, and reorganization of transient cerebral zones and structures in the human fetal brain using a correlative histological and MRI analysis. The analysis of postmortem aldehyde-fixed specimens (age range: 10 postovulatory weeks to term) revealed that, at 10 postovulatory weeks, the cerebral wall already has a trilaminar appearance and consists of: (1) a ventricular zone of high cell-packing density; (2) an intermediate zone; (3) the cortical plate (in a stage of primary consolidation) with high MRI signal intensity. The anlage of the hippocampus is present as a prominent bulging in the thin limbic telencephalon. The early fetal telencephalon impar also contains the first commissural fibers and fornix bundles in the septal area. The ganglionic eminence is clearly visible as an expanded continuation of the proliferative ventricular zone. The basal ganglia showed an initial aggregation of ...

Energy Technology Data Exchange (ETDEWEB)

The Authenticated Tracking and Monitoring System (ATMS) has been designed to address the need for global monitoring of the status and location of proliferation-sensitive items. Conceived to utilize the proposed Global Verification and Location System (GVLS) satellite link, ATMS could use the existing International Maritime Satellite commercial communication system until GVLS is operational. The ATMS concept uses sensor packs to monitor items and environmental conditions, collects a variety of events data through a sensor processing unit, and transmits the data to a satellite, which then sends data to ground stations. Authentication and encryption algorithms will be used to secure the data. A typical ATMS application would be to track and monitor the safety and security of a number of items in transit along a scheduled shipping route. This paper also discusses a possible proof-of-concept system demonstration.

International Nuclear Information System (INIS)

In this work, a mixed cationic--anionic [i.e. cetyltrimethylammonium bromide-sodium octyl sulphate] surfactant system was used to synthesize the magnetite particles. The loading content of iron ions (Fe"3"+ and Fe"2"+) into the surfactant system was varied to study its effect on the formation of magnetite, magnetic and morphological properties of the magnetite particles encapsulated by the surfactant vesicles. It has been verified that the vesicle-encapsulated magnetite particles with sizes from 100 to 200 nm were formed, which were almost independent of the loading content of iron ions. However, the morphological structure of the magnetite particles was dependent on the loading content of iron ions and there existed an optimal loading content for a full packing of the surfactant vesicles with the magnetite particles.

British Library Electronic Table of Contents (United Kingdom)

Summary 1. In the Greater Yellowstone Ecosystem, bison Bison bison and elk Cervus canadensis nelsoni act as hosts for Brucella abortus. The presence of B. abortus within wildlife populations is an important conservation issue because of the risk of brucellosis transmission from wildlife to cattle. 2. We investigated conditions facilitating contact between bison (40-60% seroprevalence) and elk on a shared winter range in the Madison headwaters area of Yellowstone National Park. We evaluated the effects of snow pack, season, elk and bison population sizes, and wolf Canis lupus predation risk on the degree of spatial overlap between bison and elk from 1991 to 2006. 3. Sixty-eight per cent of 10 093 independent elk observations occurred within the known bison wintering range, 29% occurred with...

Energy Technology Data Exchange (ETDEWEB)

As thin films become increasingly popular (for solar cells, LEDs, microelectronics, batteries), quantitative morphological information is needed to predict and optimize the film's electronic, optical and mechanical properties. This quantification can be obtained quickly and easily with X-ray diffraction using an area detector and synchrotron radiation in two simple geometries. In this paper, we describe a methodology for constructing complete pole figures for thin films with fiber texture (isotropic in-plane orientation). We demonstrate this technique on semicrystalline polymer films, self-assembled nanoparticle semiconductor films, and randomly-packed metallic nanoparticle films. This method can be immediately implemented to help understand the relationship between film processing and microstructure, enabling the development of better and less expensive electronic and optoelectronic devices.

Energy Technology Data Exchange (ETDEWEB)

A detergent-containing radioactive liquid waste originating from atomic power plants is concentrated to have about 10 wt. % detergent concentration, then dried in a thin film evaporator, and converted into powder. Powdered activated carbon is added to the radioactive waste in advance to prevent the liquid waste from foaming in the evaporator by the action of surface active agents contained in the detergent. The activated carbon is added in accordance with the COD concentration of the radioactive liquid waste to be treated, and usually at a concentration 2-4 times as large as the COD concentration of the liquid waste to be treated. A powdery product having a moisture content of not more than 15 wt. % is obtained from the evaporator, and pelletized and then packed into drums to be stored for a predetermined period.

International Nuclear Information System (INIS)

The relaxations of the Ti(0001) and Zr(0001) surfaces are studied using the plane-wave-basis pseudopotential method within the local-density approximation. We find that the first interlayer spacings of Ti(0001) and Zr(0001) are contracted with respect to the bulk spacings by 6.8% and 6.1%, respectively. Such large relaxations for the close-packed surfaces of Ti and Zr are in good agreement with recent linear-augmented-plane-wave calculations. In addition, we predict a weak vibrational effect on the surface relaxation of Zr(0001) by considering the free energy in the quasiharmonic approximation. This result can be attributed to a very strong bonding between the first- and second-layer Zr atoms as a consequence of the bond-order endash bond-length correlation. copyright 1997 The American Physical Society.

British Library Electronic Table of Contents (United Kingdom)

A dense Pd-Ag membrane reactor (MR) with 100% hydrogen selectivity packed with either Rh/La2O3 or Rh/La2O3-SiO2 as catalysts was used to carry out the dry reforming of methane. The membrane reactor simulation was performed using a well-known reactor model. For this purpose, we employed the equations derived from complete kinetic studies of the dry reforming of methane reaction in connection with both catalysts. In addition, we developed the kinetic equation for the reverse water gas shift reaction (RWGS). The combination of detailed kinetic studies with the measured permeation flux for the Pd-Ag membrane allowed a complete comparison between experimental and simulated operation variables. The variables studied for both catalysts were methane conversion and hydrogen permeation as a function...

CERN Document Server

In 1934, Reinhardt asked for the centrally symmetric convex domain in the plane whose best lattice packing has the lowest density. He conjectured that the unique solution up to an affine transformation is the smoothed octagon (an octagon rounded at corners by arcs of hyperbolas). This article offers a detailed strategy of proof. In particular, we show that the problem is an instance of the classical problem of Bolza in the calculus of variations. A minimizing solution is known to exist. The boundary of every minimizer is a differentiable curve with Lipschitz continuous derivative. If a minimizer is piecewise analytic, then it is a smoothed polygon (a polygon rounded at corners by arcs of hyperbolas). To complete the proof of the Reinhardt conjecture, the assumption of piecewise analyticity must be removed, and the conclusion of smoothed polygon must be strengthened to smoothed octagon.

Energy Technology Data Exchange (ETDEWEB)

On efficient glass capillary columns packed with graphitized thermal carbon black (GTCB) the stereoisomers of aromatic and saturated tricyclic hydrocarbons are completely separated and identified. The Henry's adsorption constants of the individual isomers were determined from mixture at different temperatures. Five isomers of perhydroanthracene, five isomers of perhydrofluorene, two isomers of perhydrophenalene, four isomers of perhydroacenaphthene, as well as phenalene, dihydrophenalene, acenaphthene and acenaphthylene were investigated. The increase of the hydrogenization degree of unsaturated tricyclic hydrocarbons reduces the retention. Among the saturated tricyclic isomers the retention becomes shorter with the larger bending of the molecules, i.e. from the molecule having more equatorial bonds to the molecules having more axial connections. The experimentally determined Henry's constants were qualitatively compared with the structure of the ...

International Nuclear Information System (INIS)

The separation and the mechanism of retention of ion associates of #alpha#-isomers of molybdic and tungstic heteropoly acids (HPA) of phosphorus(5), silicon(4), and germanium(4) with trioctylamine (TOA) on a column (80x3 mm) packed with Diasorb-130-CN (8 #mu#m) were studied in a flow of chloroform-tetrahydrofuran (THF) and chloroform-n-butanol-TOA mixtures with spectrophotometric detection at 320 nm. It is demonstrated that the adsorption of all the studied ion associates proceeds through the displacement THF molecule from the surface of the stationary phase and without the displacement of TOA molecules. Conditions for the separation of phospho- and silicomolybdic HPA and also phospho- and germanolybdic HPA were found. The chromatographic system using silica gel modified with nitrile groups as the stationary phase is of higher selective than that using ummodified silica gel.

International Nuclear Information System (INIS)

The losses of Hg from phenol formaldehyde resin - bound standards and hair samples in neutron activation analysis in case of their irradiation in the water filled nuclear reactor channel is studied. The mean losses of Hg during 20-30 hrs irradiation at (2-3)x10"1"8 n/cm"2 are 15-20% with their stopping at double Al-covers. The mean losses of Hg from standards at 200, 250 and 300 deg C are 30, 61 and 86% respectively and do not occur at 150 deg C after their 5 hour heating. The losses of Hg from hair samples packed in polyethylene tubes through the package walls in experimental conditions are not observed.

International Nuclear Information System (INIS)

Soybean is one of the most economical and nutritious food packed with basic nutrients that combat diseases stemming from mal- and under-nutrition. Despite its rich nutritional profile, use of soybean in food has been limited because soybean proteins are often associated with compounds, which could exert a negative impact on the nutritional quality of the protein. Trypsin inhibitor (TI) is one of the important anti-nutritional factors that exert negative effect by causing growth inhibition. Soybean cultivar VLS-2 was irradiated with 250 Gy gamma rays in a gamma cell (200) with 60Co source installed at BARC to induce mutations for low trypsin inhibitor content. Three mutants with lower levels of TI content were identified and can be utilized for developing elite varieties of soybean. (author)

International Nuclear Information System (INIS)

Presented in this report are the quantitative and qualitative aspects of the more than 5,800 applications of Grafoil on-plant. The subject all-graphite product was originally made by the Union Carbide Corporation. Its utilization in the forms of valve packing, gasketing and sealant tapes for leak repair and prevention on-plant since March 1970 is marked with typical zero-leak results. For all practical purposes, the successful results with Grafoil implementation indicate an unqualified control of leakage problems that began in 1967 with the V-11 and V-12 valves in the primary system of N Reactor. Meaningfully, the accruals of savings with existing and future applications shall continue to be incalculable in personnel exposure, maintenance, and capital. Inherent in the savings are the devised methodology and innovative developments coordinately employed in resolving the leak repair problems.

Energy Technology Data Exchange (ETDEWEB)

We demonstrate experimentally that the route to a jammed state for a set of bi-dispersed frictional disks, subjected to uni-axial compression from a random initial unjammed state, consists of a consolidation state, a fragile jammed state, and finally a rigid jammed state. In the consolidation regime, the pressure on the sides increases very slowly with the packing fraction {phi} and there are no detectable stress chains. In the fragile jammed state, stress chains are visible, the pressure increases exponentially with {phi}, and the fraction of moving disks drops exponentially. Eventually, a final regime where particle displacements are below our resolution and the pressure varies approximately linearly with {phi} is reached. We argue that this scenario is generic for ather mal frictional compressed particles.

British Library Electronic Table of Contents (United Kingdom)

Abstract A series of studies performed at our center demonstrates that gaseous microemboli (GME) remain a challenge in cardiac surgical procedures. Evaluation of novel oxygenators must address hemodynamic parameters and microemboli capture capability. The objective of this study is to compare two neonatal membrane oxygenators, the Quadrox i (MAQUET Cardiopulmonary AG, Hirrlingen, Germany) and the Capiox RX05 (Terumo Corporation, Tokyo, Japan), with respect to GME capture and hemodynamic energy delivery. The experimental circuit included a Maquet HL 20 heart lung machine, a Heater Cooler Unit HCU 30 (MAQUET Cardiopulmonary AG), a membrane oxygenator (Quadrox i Neonatal or Capiox RX05), and inch tubing from the COBE Heart/Lung Perfusion Pack (COBE Cardiovascular, Inc., Arvada, CO, USA). A Ca...

British Library Electronic Table of Contents (United Kingdom)

This paper is concerned with the study of the Electrorheological RayleighTaylor instability (ERTI) at the interface between a densely packed saturated poorly conducting couple stress porous layer accelerated by a lighter poorly conducting couple stress fluid in a thin shell in the presence of a transverse electric field and laser radiation. A simple theory based on fully developed flow approximations is used to derive the dispersion relation for the growth rate of ERTI. The cutoff and the maximum wave numbers and the corresponding maximum frequencies are obtained. It is shown that the effects of couple stress parameter and the electric field reduce the growth rate considerably compared to a non-conducting fluid in the absence of an electric field. These are favorable to control the surface...

British Library Electronic Table of Contents (United Kingdom)

A study was undertaken to assess the effect of different storage temperatures on senescence and postharvest performance of isolated flowers of Ranunculus asiaticus L.. The main aim of the work was to develop a cost-effective storage protocol to reduce the postharvest losses and to bring out the transportation of cut flowers of R. Asiaticus. The flowers were subjected to two different storage treatments, dry storage and wet storage, and their postharvest performance was compared under laboratory conditions. For this purpose, the buds were harvested at 8:00 AM at loose bud stage (Stage II of flower development). The harvested buds were cut to a uniform size of 15 cm and processed for dry or wet storage. For dry storage, the buds were packed after wrapping them in moistened filter papers and ...

Energy Technology Data Exchange (ETDEWEB)

The phase transformations and properties of a precipitation-hardened Ni-Cr-based alloy are investigated as a function of C, B, Nb, and Cr contents. It is found that the primary role of Nb consists in the formation of an independent phase, delta-Ni3Nb, a part of a gamma/gamma-prime-delta eutectoid (for high C and B concentrations) and in stimulating the gamma-sigma reaction consecutively with the gamma double prime-delta reaction (for low C and B concentrations). In both cases, the long-term strength characteristics of the Nb-alloyed system are relatively low. The substitution of boron for carbon contributes to a reduction in the number of nucleation sites for topologically close-packed phases and to the formation of more stable (with respect to excess compounds) M3B2 and MB2 borides. The high-boron material exhibits better properties and phase stability under mechanical and thermal loading. 13 references.

British Library Electronic Table of Contents (United Kingdom)

Injections of fuel-grade ethanol (95% v/v ethanol, 5% v/v hydrocarbon mixture as a denaturant) near the water table were conducted in two-dimensional physical models tightly packed with fine sands under varying water-table conditions. As the fuel migrated in the porous media following injection, the denaturant phase separated leaving a residual Light Non-Aqueous Phase Liquid (LNAPL) phase that occupied a region with a volume similar to that of an equal-sized spill of 100% LNAPL without ethanol. When the water table was raised, as may be expected following a catastrophic release that reaches groundwater, most of the ethanol-fuel mixture was mobilized and the vertical distribution of the generated LNAPL was increased. The lower boundary of the residual LNAPL was established during the initia...

Energy Technology Data Exchange (ETDEWEB)

A distillation column with an adjustable slope horizontal rectification section was constructed. A rotating screw brush was inserted into the section, which could be rotated from 0 to 600 rpm with an external motor. Distillation experiments were carried out using the system cyclohexane-heptane at total reflux at slopes of 0(horizontal), 5 and 10 degrees. Separation efficiency for the horizontal column was the highest of the three orientations, and was obtained as HETP from 0.04 to 0.16 m at F-factor of 0.05 to 0.4 m/s(kg/m{sup 3}){sup 1/2} in the range of 100 to 600 rpm. The HETP for each slope was roughly constant at a rotation speed of more than 300 rpm. The values of the pressure drop were found to be equivalent to those of one seventh to one fifth of conventional packed columns. (author)

International Nuclear Information System (INIS)

Recently, foods are often exposed to radiation under packed states with various wrapping materials. In this study, the effects of #gamma#-ray radiation were investigated on the additives in wrapping materials on the market. 10 - 50 kGy #gamma# radiation was irradiated to samples under sealed condition in a glass-ware. Polyethylene bag and wrapping film, polypropylene wrapping film, cup and sheet, and polystyrene cup were used as samples. And the additives in these materials were analyzed by GC/MS to evaluate the radiation effects on them. The irradiation was found to induce rapid degradation of antioxidants, especially, Irgafos 168. Some fatty acid amides used as a lubricant and a plasticizer, DBP were also reduced, but not aliphatic hydrocarbons. However, all polystyrene products used in this study included no additives. The contents of styrene dimer and trimer in those wrapping materials were not changed by #gamma#-irradiation. (M.N.)

Science.gov (United States)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m{sup 3} in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m{sup 2} in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

British Library Electronic Table of Contents (United Kingdom)

This study investigated the optimum polyphenol extraction conditions for two Nigerian green leafy vegetables, Vernonia amygdalina (VA) and Gongronema latifolium (GL) that are widely used for food and medicinal purposes. Seven different solvents were used to extract the total phenolic contents of the leaves; 100% acetone, 80% acetone, 50% acetone, 100% ethanol, 70% ethanol, 100% methanol and 70% methanol and their total phenolic contents were determined. The results showed that the 80% acetone was significantly (p<0.05) the most effective for polyphenol extraction from the leaves and generally the acetone-containing solvents were more effective than alcohol-containing solvents. The 80% acetone extract was fractionated on a silicic acid-packed column to give two main fractions: acetone elute...

British Library Electronic Table of Contents (United Kingdom)

In this study, sulfured orange peel (MOP) was used as adsorbent to investigate its adsorption behaviors of Pb^2^+ and Zn^2^+ from aqueous solutions. The effects of solution pH, adsorption time and metal ion concentration on adsorption were studied in batch experiments. Both adsorption kinetics of Pb^2^+ and Zn^2^+ proceeded rapidly and could be well described by pesudo-second-order equation. The maximum Langmuir adsorption capacities for Pb^2^+ and Zn^2^+ removal by MOP were evaluated as 164 and 80mg/g, respectively. A binary mixture of Pb^2^+ and Zn^2^+ was studied by using a packed column, suggesting that effective mutual separation and pre-concentration of Pb^2^+ away from Zn^2^+ using MOP could be satisfactory achieved. The results indicate that MOP could be employed as an effective lo...

Energy Technology Data Exchange (ETDEWEB)

The authors describe a small doubly reflecting research furnace. Its optical components, a heliostat and a concentrating array of hexagonal-in-plan-form mirrors, focus sunlight at the aperture of a cavity receiver. A perfect paraboloid of revolution would have given higher concentration ratios. But large paraboloids are difficult to make and manipulate. Small hexagons are convenient and can be close packed. Spherical mirrors centered on a sphere simplified construction and were economical. In this note they use a simple model to describe the radial distribution of the normal flux at the focus of such an array. A schematic representation of a cross section of the concentrator mirror array in a plane which includes its axis is shown.

International Nuclear Information System (INIS)

The design of solid breeder blankets is strongly affected by the low values of thermal conductivity and density of ceramic breeder pebble beds. A significant rise of both quantities would enhance the thermal performance and lead to an increased tritium breeding ratio. In order to improve these quantities pretreated lithium orthosilicate pebble material was dry pressed and subsequently sintered. The thermal conductivity of cylindrical pellets was determined by the heat pulse method using a laser flash device. A pebble bed characteristic sample was also investigated in order to check the measurement accuracy in comparison with previous results. Furthermore, two samples of low density cellular ceramics were also prepared by infiltration of polymer foams with a ceramic slurry. The thermal conductivity results show that the values are affected both by the particle size and the sample density. Thermal conductivity values of higher than 2 W/m K were ...

Energy Technology Data Exchange (ETDEWEB)

Since fuel oil meeting the requirements of current petroleum products can be produced by SASOL F-T synthetic process, the manufacturing process of hydrocarbon fuel oil from the coal-derived synthesis gas, downstream processes are being successively investigated. Mobile M-gasoline, MTG, process which produces gasoline from the natural gas-derived synthesis gas through methanol went into commercial operation in New Zealand in 1986. Although the gasoline suffices the quality of commercial gasoline by both fixed bed and fluidized bed systems, the price and service life of catalyst and control of by-product durene must be improved. Any STG processes have not been completed yet and the yield and quality of gasoline are inferior to those of gasoline produced by the MTG process. Applying two-stage process, the STG process will be more economically effective.(21 refs, 4 figs, 10 tabs)

British Library Electronic Table of Contents (United Kingdom)

A laboratory-scale multi-layer system was developed for the adsorption of PCDD/Fs from gas streams at various operating conditions, including gas flow rate, operating temperature and water vapor content. Excellent PCDD/F removal efficiency (>99.99%) was achieved with the multi-layer design with bead-shaped activated carbons (BACs). The PCDD/F removal efficiency achieved with the first layer adsorption bed decreased as the gas flow rate was increased due to the decrease of the gas retention time. The PCDD/F concentrations measured at the outlet of the third layer adsorption bed were all lower than 0.1ng I-TEQNm-3. The PCDD/Fs desorbed from BAC were mainly lowly chlorinated congeners and the PCDD/F outlet concentrations increased as the operating temperature was increased. In addition, the r...

Energy Technology Data Exchange (ETDEWEB)

The Next Generation Nuclear Plant (NGNP), a demonstration reactor and hydrogen production facility proposed for construction at the INEEL, is expected to be a high-temperature gas-cooled reactor (HTGR). Computer codes used in design and safety analysis for the NGNP must be benchmarked against experimental data. The INEEL and ANL have examined information about several past and present experimental and prototypical facilities based on HTGR concepts to assess the potential of these facilities for use in this benchmarking effort. Both reactors and critical facilities applicable to pebble-bed and prismatic block-type cores have been considered. Four facilities--HTR-PROTEUS, HTR-10, ASTRA, and AVR--appear to have the greatest potential for use in benchmarking codes for pebble-bed reactors. Similarly, for the prismatic block-type reactor design, two experiments have been ranked as having the highest priority--HTTR and VHTRC.

Energy Technology Data Exchange (ETDEWEB)

Universal Oil Products, Inc. (UOP) of Des Plaines, Illinois has contracted A.E. Roberts & Associates, Inc. (AERA) of Atlanta, Georgia to prepare a sensitivity analysis for the development of the Fluidized-bed Copper Oxide (FBCO) process. As proposed by AERA in September 1991, development of the FBCO process design for a 500 mega-watt (MW) unit was divided into three tasks: (1) Establishment of a Conceptual Design, (2) Conceptual Design, (3) Cost Analysis Task 1 determined the basis for a conceptual design for the 500 megawatt (MW) FBCO process. It was completed by AERA in September of 1992, and a report was submitted at that time {open_quotes}Establishment of the Design Basis for Application to a 500 MW Coal-fired Facility.{close_quotes} Task 2 gathered all pertinent data available to date and reviewed its applicability to the 500 MW FBCO process. Work on this task was carried out on a joint basis by the AERA team members: Roberts & Schaefers worked on the ...

Energy Technology Data Exchange (ETDEWEB)

Factors important in choosing between process concepts were mechanical complexity and amenability to scale-up studies. The culmination of this work was a process concept known as Staged Turbulent Bed Retorting Process (STB), which has now been tested in pilot plants. Operating conditions are described. The environment in the retort section can be described as a staged, moving bed of particles, in which a portion of the particles are fluidized at gas velocities well below minimum fluidization velocity of many of the particles. Research and engineering evaluations have established that the STB provides prospects for the responsible development of oil shale resources on a commercial scale. A 320 ton/d semiworks unit, the next technological step, will be commissioned shortly. This unit will be large enough to provide scale-up data for design of modules and to demonstrate the entire process, generating data needed to optimize, design, and construct ...

Energy Technology Data Exchange (ETDEWEB)

Chemical-looping combustion is a promising technology for the combustion of gas or solid fuel with efficient use of energy and inherent separation of CO{sub 2}. Chemical-looping combustion of methane with calcium sulfate as a novel oxygen carrier was conducted in a laboratory scale fixed bed reactor. The effects of reaction temperature, gas flow rate, sample mass, and particle size on reduction reactions were investigated and an optimum operating condition was determined. The results show that this novel oxygen carrier has a high reduction reactivity and stability in a long-time reduction/oxidation test. The conversions of CH{sub 4} increased with a higher temperature, smaller gas flow rate, larger sample mass and smaller particle size. The suitable reaction temperature seems to be around 950 C. Low temperatures lead to a low CH{sub 4} conversion, but a significant SO{sub 2} formation was observed at a higher temperature. The release of SO{sub 2}, CO, H{sub 2} via ...

Science.gov (United States)

We investigated the effect of pretreatment on the physicochemical characteristics-crystallinity, bed porosity, and volumetric specific surface of soybean hulls and production of cellulolytic enzymes in solid-state fermentation of Trichoderma reesei and Aspergillus oryzae cultures. Mild acid and alkali and steam pretreatments significantly increased crystallinity and bed porosity without significant change inholocellulosic composition of substrate. Crystalline and porous steam-pretreated soybean hulls inoculated with T. reesei culture had 4 filter paper units (FPU)/g-ds, 0.6?IU/g-ds ?-glucosidase, and 45?IU/g-ds endocellulase, whereas untreated hulls had 0.75?FPU/g-ds, 0.06?IU/g-ds ?-glucosidase, and 7.29?IU/g-ds endocellulase enzyme activities. In A. oryzae steam-pretreated soybean hulls had 47.10?IU/g-ds endocellulase compared to 30.82?IU/g-ds in untreated soybean hulls. Generalized linear statistical model fitted to enzyme activity data ...

Energy Technology Data Exchange (ETDEWEB)

Pyrolysis of Greek fir wood samples in a fluidized bed reactor was studied. The experimental conditions selected control the yield of gaseous, liquid and solid products. The factors examined were: pyrolysis temperature, mean particle size, pressure, residence time of volatiles, lignin content of biomass and moisture content. The experiments were performed on the basis of a 12-run Plackett-Burman fractional factorial design. Statistical analysis of the data showed that the pyrolysis temperature is the main factor affecting the distribution of the yields of liquids, their phenolic fraction and gases in the range of experimental conditions tested. Empirical expressions were obtained from linear regression giving the yields of liquids, phenols and gases in terms of temperature. The maximum predicted yields were 56 and 12 wt.% on a moisture-free basis at 520 C and 545 C for liquids and phenols, respectively. The yield of gases increased proportionally with temperature. ...

Science.gov (United States)

The magnetically fluidized bed (MFB) was used as the reactor in a novel semidry flue gas desulfurization (FGD) process to achieve high desulfurization efficiency. Experiments in a laboratory-scale apparatus were conducted to reveal the effects of approach to adiabatic saturation temperature, Ca/S molar ratio and applied magnetic field intensity on SO(2) removal. Results showed that SO(2) removal efficiency can be obviously enhanced by decreasing approach to adiabatic saturation temperature, increasing Ca/S molar ratio, or increasing applied magnetic field intensity. At a magnetic field intensity of 300Oe and a Ca/S molar ratio of 1.0, the desulfurization efficiency (excluding desulfurization efficiency in the fabric filter) was over 80%, while spent sorbent appeared in the form of dry powder. With the SEM, XRD and EDX research, it can be found that the increase of DC magnetic field intensity can make the surface morphology on the surface of the ferromagnetic ...

Energy Technology Data Exchange (ETDEWEB)

A divergence correction is conventionally applied to zero-offset data in an effort to preserved amplitude information. The conventional divergence correction compensates for the geometrical spreading of a point source in a horizontally layered medium where velocity varies with depth only. The dip-dependent divergence correction extends the conventional correction for improved amplitude processing of dipping beds. The dip-dependent divergence correction is computed by dynamic ray tracing, and applied to stacked data using a dip decomposition technique. This correction decreases amplitudes relative to the conventional correction for steep dips and late times. In a data example from the Gulf of Mexico, the conventional correction over- amplified the reflection off a salt dome flank by a factor of 1.6. High amplitudes near salt flanks are also associated with the presence of hydrocarbons. Applying the dip-dependent divergence correction ensures that ``bright spots`` ...

Energy Technology Data Exchange (ETDEWEB)

An investigation was conducted into alternative techniques for zinc and electrolyte regeneration and reuse in the refuelable zinc/air battery that was developed by LLNL and previously tested on a moving electric bus using cut wire. Mossy zinc was electrodeposited onto a bipolar array of inclined Ni plates with an energy consumption of 1.8 kWh/kg. Using a H{sub 2}-depolarized anode, zinc was deposited at 0.6 V (0.8 kA/m{sup 2}); the open circuit voltage was 0.45 V. Three types of fuel pellets were tested and compared with results for 0.75 mm cut wire: spheres produced in a spouted bed (UCB); coarse powder produced by gas-atomization (Noranda); and irregular pellets produced by chopping 1-mm plates of compacted zinc fines (Eagle-Picher, Inc.). All three types transported within the cell. The coarse powder fed continuously from hopper to cell, as did the compacted pellets (< 0.83 mm). Large particles (> 0.83 mm; Eagle-Picher and UCB) failed to feed from ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes statistical methods used to evaluate data for toluene (at several typical operating temperatures and humidity levels) and to determine which measure of humidity (relative or absolute) is more important in determining carbon adsorption efficiency. The water content of a solvent-laden stream is critical for its control via carbon adsorption, especially at relative humidities about 50-70%. (Relative humidity is the percent of saturation: absolute humidity is the total water content.)

Energy Technology Data Exchange (ETDEWEB)

In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

To expand the information base on molecular accessibility in solvent swelled coal, Argonne Premium Coal Samples (APCS) were swelled in polar, basic solvents before and after moisture loss and upon air oxidation. So far studies have been reported on the changes in pore size distribution as a function of temperature when polar basic swelling solvents are used. Additional studies employing EPR spin probe techniques performed on the breaking up of the hydrogen bonding between bedding planes were later confirmed by magnetic resonance imaging at Argonne National Lab and the University of Illinois.

CERN Document Server

Having always been at the forefront of information management and open access, High-Energy Physics (HEP) proves to be an ideal test-bed for innovations in scholarly communication including new information and communication technologies. Three selected topics of scholarly communication in High-Energy Physics are presented here: A new open access business model, SCOAP3, a world-wide sponsoring consortium for peer-reviewed HEP literature; the design, development and deployment of an e-infrastructure for information management; and the emerging debate on long-term preservation, re-use and (open) access to HEP data.

Energy Technology Data Exchange (ETDEWEB)

In the well-known devices for increasing the decontamination factor in the treatment of radioactive waste water by evaporation, which consist of narrowing devices with evaporator sump and condenser, droplets of liquid and solid particles are carried over from the breeder space, which are radioactive and therefore make the decontamination factor worse. Better results are obtained if one places a fibre bed filter between the evaporator sump and the condenser, preferably in a horizontal connecting pipe between the evaporator sump and the condenser.

Energy Technology Data Exchange (ETDEWEB)

Red mud, and red mud activated by dissolution in hydrochloric acid and reprecipitation with ammonia, were tested as catalysts for the hydrogenation of an anthracene oil in a trickle-bed reactor. Conversion data were determined for the different polyaromatic compounds in the anthracene oil. Red mud shows appreciable catalytic activity, which is enhanced by the activation. Although both red mud and activated red mud are less active than a commercial Ni-Mo/[gamma]-alumina hydrotreating catalyst, the difference in activity is smaller when conversion to hydroaromatics instead of total conversion of reactants is considered. 20 refs., 8 figs., 3 tabs.

Energy Technology Data Exchange (ETDEWEB)

Visualizations by real-time neutron radiography are demonstrated of various flow patterns of nitrogen gas-water two-phase flow in a stainless-steel tube, water inverted annular flow in a stainless-steel tube, flashing flow in an aluminium nozzle and fluidized bed in aluminium tube and vessels. Photographs every 1/60 s are presented by an image processing method to show the dynamic behaviours of the various flow patterns. It is shown that this visualization method can be applied efficiently to multiphase flow researches and will be applicable to multiphase flows in industrial machines. (author).

Energy Technology Data Exchange (ETDEWEB)

The concept of using agricultural residues, especially cotton gin trash (CGT), as a fuel for a small cogeneration power plant based on fluidized bed gasification (FBG) requires that three problems be solved: (1) ash must be removed from the low calorific value (LCV) gas prior to combustion; (2) the high NO/sub x/ emissions associated with many biomass fuels must be significantly reduced; (3) a systems analyses of engineering/economic feasibility for potential applications must be developed. This paper addresses current research at TAMU pertaining to these problems.

Energy Technology Data Exchange (ETDEWEB)

Radioactive wastes are generally classified into 3 type depending on their physical property: liquid, solid and gaseous type. State-of -the art concerning liquid waste treatment has already been published; KAERI/TR-1315/99. Solid wastes classification package and treatment method will be studied to effectively manage them during the practical decommissioning work. All of the spent fuel produced during the operation of the TRIGA Mark-2 and 3 have been transported to the US last year, 1998, according to the spent fuel management strategy set-up by the US government for the non-proliferation of nuclear energy. Solid wastes are mainly all equipment existing inside of the reactors, activated concrete among the bio-shielded concrete, pipes, pimps, resin filter and it's housings, heat-exchangers, liquid waste storage tanks, to radioactive waste storage treatment facilities and so on. Solid wastes are generally low-level. They are classified according to the national regulation and ...

Energy Technology Data Exchange (ETDEWEB)

The design of separation devices, particularly for solvent-based selective removal of H{sub 2}S from CO{sub 2}, requires an accurate mathematical model. Unfortunately, this requirement for high accuracy is often in conflict with the need for efficient computation. The addition of more and more complicated analyses, such as a move from Henry's law to a method incorporating gas and liquid activities for computing vapor liquid equilibria, may give a more accurate solution, but only at the cost of decreased computational efficiency. The efforts in this work have been directed toward two goals. The first was to develop an accurate mathematical model for the aqueous methyldiethanolamine (MDEA) system. The steady-state packed column model developed in this work has been tested with data from Schubert (1988) to verify its accuracy. The second goal was to modify the model to improve its computational efficiency. Areas such as vapor-liquid equilibrium calculations, ...

Science.gov (United States)

The objective of the study was the kinetic modeling of the effect of storage temperature on the quality and shelf life of chilled fish, modified atmosphere-packed (MAP), and osmotically pretreated with the addition of nisin as antimicrobial agent. Fresh gilthead seabream (Sparus aurata) fillets were osmotically treated with 50% high dextrose equivalent maltodextrin (DE 47) plus 5% NaCl. Water loss, solid gain, salt content, and water activity were monitored throughout treatment and treatment conditions were selected for the shelf life study. Untreated and osmotically pretreated slices with and without nisin (2 x 10(4) IU/100 g osmotic solution), packed in air or modified atmosphere (50% CO(2)-50% air), and stored at controlled isothermal conditions (0, 5, 10, and 15 degrees C) were studied. Quality assessment and modeling were based on growth of several microbial indices, total volatile nitrogen, trimethylamine nitrogen, lipid oxidation ...

Energy Technology Data Exchange (ETDEWEB)

Prototype tests conducted during the winter of 1989/90 have successfully demonstrated an economical design for air stripping volatile hydrocarbons from oily tanker ballast water. The prototype air stripper, developed for Alyeska's Ballast Water Treatment (BWT) facility in Valdez, Alaska, ran continuously for three months with an average removal of 88% of the incoming volatile organics. Initially designed to remove oil and grease compounds from tanker ballast water, the BWT system has been upgraded to a three-step process to comply with new, stringent regulations. The BWT biological oxidation process enhances the growth of bacteria present in the incoming ballast water through nutrient addition, aeration, and recirculation within a complete-mixed bioreactor. The average removal of BETX is over 95%, however, occassional upsets required the placement of a polishing air stripper downstream of the aeration tanks. Packed-tower air stripping was investigated but ...

Energy Technology Data Exchange (ETDEWEB)

A fast and simple flow-through optosensor was designed and characterized for the direct screening of four tetracycline (TCC) antibiotics (tetracycline, oxytetracycline, chlortetracycline and doxycycline) in water and bovine milk samples. The proposed optosensor provides rapid binary yes/no overall responses, being appropriate for the screening of this family of antibiotics above or below a pre-set concentration threshold. The experimental set-up is based on a flow-injection manifold coupled on-line to a phosphorescence detector. Aliquots of the samples are pretreated with Eu(III) to form room temperature phosphorescent metal chelates and injected in the flow manifold. Those chelates are then on-line retained on a conventional flow-cell (packed with polymeric Amberlite XAD-4 particles) which is placed inside the cell holder of the phosphorimeter. After the emission is registered, the antibiotic-metal complexes are eluted from the packed resin ...

Science.gov (United States)

The performance of intermolecular potential models on the adsorption of carbon tetrachloride on graphitized thermal carbon black at various temperatures is investigated. This is made possible with the extensive experimental data of Machin and Ross(1), Avgul et al.,(2) and Pierce(3) that cover a wide range of temperatures. The description of all experimental data is only possible with the allowance for the surface mediation. If this were ignored, the grand canonical Monte Carlo (GCMC) simulation results would predict a two-dimensional (2D) transition even at high temperatures, while experimental data shows gradual change in adsorption density with pressure. In general, we find that the intermolecular interaction has to be reduced by 4% whenever particles are within the first layer close to the surface. We also find that this degree of surface mediation is independent of temperature. To understand the packing of carbon tetrachloride in slit pores, we compared the ...

International Nuclear Information System (INIS)

Ab initio total energy calculations within the framework of density functional theory have been performed for atomic hydrogen and oxygen chemisorption on the (0001) surface of double hexagonal packed (dhcp) americium using a full-potential all-electron linearized augmented plane wave plus local orbitals method. Chemisorption energies were optimized with respect to the distance of the adatom from the relaxed surface for three adsorption sites, namely top, bridge, and hollow hcp sites, the ad-layer structure corresponding to the coverage of a 0.25 monolayer in all cases. Chemisorption energies were computed at the scalar-relativistic level (no spin-orbit coupling NSOC) and at the fully relativistic level (with spin-orbit coupling SOC). The two-fold bridge adsorption site was found to be the most stable site for O at both the NSOC and SOC theoretical levels with chemisorption energies of 8.204 eV and 8.368 eV respectively, while the three-fold hollow hcp adsorption ...

Energy Technology Data Exchange (ETDEWEB)

A hypothesis on the transition of a fully water-saturated coal bed methane reservoir from single-phase flow through unsaturated flow to the two-phase flow regime was developed and substantiated using field data. The concept of parameter measurement windows was introduced to obtain the required reservoir parameters from flow testing. A new empirical relationship for capillary pressure vs. saturation, referred to as the Fermi distribution, was developed and shown to fit the capillary pressure-saturation data for coal, sandstone, and other consolidated and unconsolidated materials. New approximate analytic solutions for flow to a sink from an infinite coal bed reservoir with desorbing methane have been developed and verified using numerical models for the following cases: (1) single-phase gas flow with desorption; (2) single-phase water flow in fully water-saturated and unsaturated flow regimes. A numerical model based on finite-difference method ...

International Nuclear Information System (INIS)

Full text.Sediments are the ultimate sink of trace elements. The total metal analysis may only give information concerning possible enrichment of metals. The analysis of metal partitioning in the different chemical components of sediments (exchangeable, carbonate, easily reducible, moderately reducible, organic and residual); give a detailed information on the way in which these metals are bound to sediments, their mobilization capacity and their ability to affect water quality under different environmental conditions. The studied river basin is dominated by limestone formation, the enrichment of metals in the carbonate sediment fraction is a high probability. The objective of the study was to determine the percentage of the total metal content (Fe, Mn, Zn, Cu and Pb) in the six chemical fractions of the bed load sediments of Nahr-Ibrahim river during the dry season and verify the role of carbonate for metal sediment deposition. Bed load ...

Energy Technology Data Exchange (ETDEWEB)

Approximately 700m of deep water clastic deposits of Mt. Messenger Formation are superbly exposed along the Taranaki coast of North Island, New Zealand. Biostratigraphy indicates the interval was deposited during the time span 10.5-9.2m.y. in water depths grading upward from lower bathyal to middle-upper bathyal. This interval is considered part of a 3rd order depositional sequence deposited under conditions of fluctuating relative sea-level, concomitant with high sedimentation rates. Several 4th order depositional sequences, reflecting successive sea-level falls, are recognized within the interval. Sequence boundaries display a range of erosive morphologies from metre-wide canyons to scours several hundred metres across. All components of a generic lowstand systems tract--basin floor fan, channel-levee complex and progading complex--are present in logical and temporal order. They are repetitive through the interval, with the relatively shallower-water components becoming more ...

Science.gov (United States)

Context: The Balanced Budget Act (BBA) of 1997 allowed some rural hospitals meeting certain requirements to convert to Critical Access Hospitals (CAHs) and changed their Medicare reimbursement from prospective to cost-based. Some subsequent CAH-related laws reduced restrictions and increased payments, and the number of CAHs grew rapidly. Purpose: To examine factors related to hospitals' decisions to convert and time to CAH conversion. Methods: Eighty-nine rural hospitals in Iowa were characterized and observed from 1998 to 2005. Cox proportional hazards models were used to identify the determinants of time to CAH conversion. Findings: T-test and one-covariate Cox regression indicated that, in 1998, Iowa rural hospitals with more staffed beds, discharges, and acute inpatient days, higher operating margin, lower skilled swing bed days relative to acute days, and located in relatively high density counties were more likely to convert later or not ...

Energy Technology Data Exchange (ETDEWEB)

Initially, the decision of the operator in Dortmund-Derne to select the impact-type separator concept is explained. None of the tenderers for this 52 t/h boiler could supply references for this fluidized bed steam generator concept with staged combustion in a high-expansion fluidized bed. Under the circumstances, the simple configuration of the Steinmueller fluidized bed steam generator, its compact construction, the reduced amount of refractory and the operational behaviour of the boiler resulting therefrom were decisive in the operator`s decision to select this concept. The development schedule shows the individual stages from cold and hot trials in various test rigs and pilot plants to the final design. So far, this fluidized bed steam generator concept has been realized in the plants Derne (52 t/h), commissioned in November 1989, and Brilon (100 t/h), commissioned in November 1990. The discussion on ...

International Nuclear Information System (INIS)

Carbon stable isotope trichloroethylene ("1"3C TCE) was used to investigate the formation of chloromethane (CM) during the electrolytic dechlorination of trichloroethylene (TCE) at a granular-graphite packed cathode. A method was developed to use a conventional GC/MS to analyze and quantify regular and "1"3C TCE and their dechlorination products. The concentration of a "1"3C compound can be calculated, based on the concentration of its regular counterpart, from the response ratio of two fragments of different mass per charge values from the compounds in a sample and two characteristic MS spectrum ratios: one is the response ratio of the two fragments of the regular compound, and the other is the response ratio of the corresponding fragments of the regular and "1"3C compounds at the same concentrations. The method was used to analyze the regular and "1"3C compounds observed in an experiment of dechlorination in an ammonium acetate solution that contained both ...

Energy Technology Data Exchange (ETDEWEB)

A surplus USN 40 mm ammunition can was subjected to a variety of tests. Pressure tests were carried out with nitrogen gas, followed by the venting of actual Li/SO/sub 2/ cells and batteries inside the can. A fire test was also conducted on a can packed with 10 each 10-cell batteries surrounded by vermiculite. Test results indicate the US Navy (USN) 40-mm ammunition can is suitable as a shipping container for Li/SO/sub 2/ batteries on passenger aircraft. To provide a further measure of safety, a sulfur dioxide getter was incorporated into the can. Studies indicated a commercial material, ASC carbon, is suitable for this purpose. The granular material was packaged in porous paper desiccant bags and placed in the can with the batteries and vermiculite. The batteries were vented inside the sealed can and the internal pressure monitored. Pressure returned to normal within several minutes, indicating that this arrangement should prevent sulfur dioxide (SO/sub 2/) gas ...

International Nuclear Information System (INIS)

Radioactive iron is used to follow up some haematologic indices in birds infected with irradiated spirochetes of the Borrelia anderina species. Use is made of a total of 90 cockerels, aged two months, divided into three groups: 1st group - cockerels inoculated with spirochetes that had been gamma-irradiated at the rate of 40000 R; 2nd group - cockerels inoculated with untreated spirochetes; and 3rd group - normal cockerels. The infective material consisted of strain Rouen spirochetes of the Pamoukchii serotype. Radiometric studies were also carried out for establishing to what extent radioactive iron is incorporated in the erythrocytes and is deposited in the liver, spleen, and marrow of the investigated birds. Classical methods of investigation were employed to determine the erythrocyte, leukocyte, and thrombocyte counts, the haemoglobin content (after Sahli) as well as the erythrocyte pack after the method of Todorov. It is found that the inoculation of ...

International Nuclear Information System (INIS)

The detailed electronic energy band structure of hexagonal close-packed #alpha#-zirconium, corresponding to the atomic configuration of 4d"25s"2 of its four outermost valence electrons, has been computed by the composite-wave variational version of the augmented-plane-wave(APW) method in conjunction with the X#alpha#(#alpha# = 0.70424) exchange approximation for obtaining the potentials. From these data the electronic density of states and its angular-momentum-decomposed components have been obtained by the Raubenheimer-Gilat method. These quantities are required in order to calculate the electron-phonon interaction parameter (lambda) and the superconducting transition temperature (Tsub(c)) within the framework of the theories of Gaspari and Gyorffy and McMillan. A study of the variation of Tsub(c) with the Coulomb pseudopotential (#mu#*) revealed that #mu#* = 0.1 yields the best agreement between theory and experiment for #alpha#-Zr. Also studied from the energy ...

Science.gov (United States)

The gadolinium isotopes are interesting for reactor applications as well as for medicine and astrophysics. The gadolinium isotopes have some of the largest neutron capture cross sections. As a consequence they are used in the control rod in reactor fuel assembly. From the basic science point of view, there are seven stable isotopes of gadolinium with varying degrees of deformation. Therefore they provide a good testing ground for the study of deformation dependent structure such as the scissors mode. Decay gamma rays following neutron capture on Gd isotopes are detected by the DANCE array, which is located at flight path 14 at the Lujan Neutron Scattering Center at Los Alamos National Laboratory. The high segmentation and close packing of the detector array enable gamma-ray multiplicity measurements. The calorimetric properties of the DANCE array coupled with the neutron time-of-flight technique enables one to gate on a specific resonance of a specific isotope in ...

CERN Document Server

Given a Gibbs point process $\\P^{\\Psi}$ on $\\R^d$ having a weak enough potential $\\Psi$, we consider the random measures $\\mu_\\la := \\sum_{x \\in \\P^{\\Psi} \\cap Q_\\la} \\xi(x, \\P^{\\Psi} \\cap Q_\\la) \\delta_{x/\\la^{1/d}}$, where $Q_{\\la} := [-\\la^{1/d}/2,\\la^{1/d}/2]^d$ is the volume $\\la$ cube and where $\\xi(\\cdot,\\cdot)$ is a translation invariant stabilizing functional. Subject to $\\Psi$ satisfying a localization property and translation invariance, we establish weak laws of large numbers for $\\la^{-1} \\mu_\\la(f)$, $f$ a bounded test function on $\\R^d$, and weak convergence of $\\la^{-1/2} \\mu_\\la(f),$ suitably centered, to a Gaussian field acting on bounded test functions. The result yields limit laws for geometric functionals on Gibbs point processes including the Strauss and area interaction point processes as well as more general point processes defined by the Widom-Rowlinson and hard-core model. We provide applications to random sequential ...

Energy Technology Data Exchange (ETDEWEB)

Three dispersants (stearic acid, oleic acid, and poly-(12-hydroxystearic acid)) are compared for their ability to produce low-viscosity suspensions of zirconia in kerosene. Rheological measurements and sediment packing density measurements show that poly(12-hydroxystearic acid) is a better dispersant than stearic acid or oleic acid; this is explained in terms of the longer tail of the poly-(12-hydroxystearic acid) surfactant molecule. The amount of dispersant can be optimized to reduce viscosity and yield point of the suspension, and to eliminate thixotropic hysteresis. The use of a dispersion medium of lower viscosity than the dispersant makes it easy to detect when complete monolayer coverage has been achieved. The loss of pseudoplasticity, brought about by a higher degree of deflocculation, can be recovered by increasing the volume fraction of solids of a suspension and this is beneficial in the plastic forming of ceramics. Rheological measurements showed that ...

International Nuclear Information System (INIS)

One of the most effective removing processes of iodine species is what is called ''Iodox Process'', which contains oxidation and absorption of iodine species by highly concentrated nitric acid. The result of fundamental test with bubble column in this process had been reported. Present paper describes the fundamental experiment by the use of packed column. This experiment has been carried out to clear the effect of feed gas flow rate, nitric acid flow rate, nitric acid concentration, and methyl iodide concentration on removal efficiency of methyl iodide. The following results were obtained. The decontamination factor of methyl iodide (DF) increases exponentially with nitric acid concentration, which agrees with the result obtained by using the bubble column. The factor is in inverse proportion to feed gas flow rate, and is also almost independent of nitric acid flow rate and methyl iodide concentration. The relation between the decontamination factor and the ...