Energy Technology Data Exchange (ETDEWEB)

From April 1990 through January 1991, the feasibility of recycling Navy shipboard-generated plastic wastes was explored. Normally, plastic wastes are source separated aboard Navy ships and retained for shoreside disposal in accordance with new fleet requirements implementing MARPOL Annex V that prohibits the discharge of plastics at sea. Over 23,000 pounds of shipboard plastic wastes from USS Lexington (AVT 16) and ships from the Norfolk Naval Base were recycled into park benches, picnic tables and carstops that have been distributed back to the Navy bases for use. Navy shipboard plastics must undergo sorting prior to recycling because Navy plastic waste contains large quantities of composite plastic items (e.g., plastic/paper) that are not easily recyclable. Recycling food-contaminated plastics is not practical due to sanitation problems encountered during handling. However, certain items have good resale value if separated by resin type and ...

Science.gov (United States)

... Descriptors : *AMMUNITION, *CONTAINERS, *CARTRIDGES, *COMBUSTIBLE CARTRIDGE CASES, *CARTRIDGE CASES, *ANTITANK ...

International Nuclear Information System (INIS)

The report describes the studies carried out to design a non-destructive system for the radiological characterization of packages containing LLW and MLW. This technique is applied for quantitative and qualitative gamma emitters determination in packages with homogeneous and heterogeneous matrices as well as the development of a maximum activity points location system. Development involves also the automatization for its industrial use.

International Nuclear Information System (INIS)

Recent seizures of nuclear materials, and particularly of fissionable nuclear materials, have resulted in an increased awareness of the need for fieldable instrumentation for the detection and characterization of suspect packages and materials. The ability to perform in-field assessments of materials contained in suspect packages is important for several reasons. First, and most importantly, determination of the type and quantity of material provides information critical to personnel safety. The personnel at potential risk may include both the general population in the area of the package and incident response personnel. Additionally, it would be advantageous to gain information that could result in attribution of the suspect package to a particular facility or pathway as soon as possible after interception. Limited access to a suspect package could also require ...

UK PubMed Central (United Kingdom)

The genomic viral RNA (vRNA) segments of influenza A virus contain specific packaging signals at their termini that overlap the coding regions. To further characterize cis-acting signals...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report describes mathematical predictions for the migration of radionuclides from an emplaced radioactive waste container. The model assumes a spherical-equivalent waste solid surrounded by backfill but neglects the effect of decay heat. 7 refs., 2 tabs. (TEM)

Energy Technology Data Exchange (ETDEWEB)

The University of Groningen (RUG) has developed an expert system on cleaning of biomass producer gas. This work was carried out in close co-operation with the Biomass Technology Group B.V. (BTG) in Enschede, The Netherlands within the framework of the EC supported JOR3-CT95-0084 project. The expert system was developed as a tool for the designer-engineer of downstream gas cleaning equipment and consists of an information package and a flowsheet package. The packages are integrated in a client/server system. The flowsheeting package of the expert system has been designed for the evaluation of different gas cleaning methods. The system contains a number of possible gas cleaning devices such as: cyclone, fabric filter, ceramic filter, venturi scrubber and catalytic cracker. The user can select up to five cleaning steps in an arbitrary order for his specific gas cleaning problem. After ...

Energy Technology Data Exchange (ETDEWEB)

This Packaging Review Guide (PRG) provides guidance for Department of Energy (DOE) review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE Order 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his or her review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. This PRG is generally organized at the section level in a format similar to that recommended in Regulatory Guide 7.9 (RG 7.9). One notable exception is the addition of Section 9 (Quality Assurance), which is not included as a separate chapter in RG 7.9. Within each section, this PRG addresses the technical and ...

Science.gov (United States)

Canada will provide telescope baffles and fine error sensor assemblies. ..... ( Ongoing) Flight tests aboard sounding rockets and balloon planned for FY 1995. .... the effects of incoming energetic particles and solar radiation on the ...

Science.gov (United States)

Astronaut crew medical officers (CMO) aboard the International Space Station (ISS) receive 40 hours

International Nuclear Information System (INIS)

Radiation sterilization has several merits that it is a positively effective sterilization method, it can be used to sterilize low heat-resistant containers and high gas barrier films, and there is no possibility of residual chemicals being left in the packages. It has been commercially used in 'Bag in a Box' and some food containers. The #gamma# ray and an electron beam are commonly used in radiation sterilization. The #gamma# ray can sterilize large size containers and containers with complex shapes or sealed containers due to its strong transmission capability. However, since the equipment tends to be large and expensive, it is generally used in off production lines. On the other hand, it is possible to install and electron beam system on food production lines since the food can be processed in a short time due to its high beam coefficient and its ease of ...

International Nuclear Information System (INIS)

Two-phase flow, thermal management systems are currently being considered as an alternative to conventional, single phase systems for future space missions because of their potential to reduce overall system mass, size, and pumping power requirements. Knowledge of flow regime transitions, heat transfer characteristics, and pressure drop correlations is necessary to design and develop two-phase systems. This work is concerned with microgravity, two-phase flow regime analysis. The data come from a recent sets of experiments. The experiments were funded by NASA Johnson Space Center (JSC) and conducted by NASA JSC with Texas A ampersand M University. The experiment was on loan to NASA JSC from Foster-Miller, Inc., who constructed it with funding from the Air Force Phillips Laboratory. The experiment used R12 as the working fluid. A Foster-Miller two phase pump was used to circulate the two phase mixture and allow separate measurements of the vapor and liquid flow streams. The experimental ...

Energy Technology Data Exchange (ETDEWEB)

TOXCHEM is a microcomputer based modelling system for predicting the fate of toxic contaminants in wastewater treatment plants. The package evaluates concentrations of toxics in final effluent and waste sludge, and mass air emissions from municipal or industrial activated sludge wastewater treatment plants. Maximum allowable influent concentrations of toxics required to meet effluent discharge or air emission limits can also be estimated. The package contains a read-only database with treatability parameters for over 100 contaminants, including organic compounds and metals. If effluent or sludge quality limits have been specified, treatment plant owners and operators can use the package to estimate the permissable discharge limits for dischargers to their collection system. A hypothetical example is provided of application of the software to a planning problem involving the start up of a new operation ...

Science.gov (United States)

With major D&D projects ongoing or being planned, and also with the daily management of radwaste from nuclear facilities, the potential role of transport packagings has often been overlooked: here will one rely essentially on drums, there several local waste processing units are built, elsewhere decommissioned facilities are cut in small bits to fit into small containers by far less efficient. The present paper proposes to illustrate how integrating a transport system from the start may influence operational choices of waste management.

Energy Technology Data Exchange (ETDEWEB)

Electrochemical cyclic potentiodynamic polarization (CPP) experiments were performed on several candidate high-performance waste package container materials to evaluate their susceptibility to localized corrosion in aqueous environments relevant to the potential underground high-level nuclear waste repository. This paper presents the results of this study showing the effects of chloride ion (Cl) concentrations, pH, temperature, and electrochemical potential scan rate on the pitting corrosion behavior of these materials.

Energy Technology Data Exchange (ETDEWEB)

The Savannah River Site (SRS) is currently developing a new facility, the Actinide Packaging and Storage Facility (APSF), to process and store legacy materials from the United States nuclear stockpile. A variety of materials, with a variety of properties, packaging and handling/storage requirements, will be processed and stored at the facility. Since these materials are hazardous and radioactive, automation will be used to minimize worker exposure. Other benefits derived from automation of the facility include increased throughput capacity and enhanced security. The diversity of materials and packaging geometries to be handled poses challenges to the automation of facility processes. In addition, the nature of the materials to be processed underscores the need for safety, reliability and serviceability. The application of automation in this facility must, therefore, be accomplished in a rational and disciplined manner to ...

Energy Technology Data Exchange (ETDEWEB)

This document describes payload control at LLNL to ensure that all shipments of CH-TRU waste in the TRUPACT-II (Transuranic Package Transporter-II) meet the requirements of the TRUPACT-II SARP (safety report for packaging). This document also provides specific instructions for the selection of authorized payloads once individual payload containers are qualified for transport. The physical assembly of the qualified payload and operating procedures for the use of the TRUPACT-II, including loading and unloading operations, are described in HWM Procedure No. 204, based on the information in the TRUPACT-II SARP. The LLNL TRAMPAC, along with the TRUPACT-II operating procedures contained in HWM Procedure No. 204, meet the documentation needs for the use of the TRUPACT-II at LLNL. Table 14-1 provides a summary of the LLNL waste generation and certification procedures as they relate to TRUPACT-II payload ...

International Nuclear Information System (INIS)

On July 18, 2001, a freight train carrying hazardous (non-nuclear) materials derailed and caught fire while passing through the Howard Street railroad tunnel in downtown Baltimore, Maryland. The United States Nuclear Regulatory Commission (USNRC), one of the agencies responsible for ensuring the safe transportation of radioactive materials in the United States, undertook an investigation of the train derailment and fire to determine the possible regulatory implications of this particular event for the transportation of spent nuclear fuel by railroad. Shortly after the accident occurred, the USNRC met with the National Transportation Safety Board (NTSB, the U.S. agency responsible for determining the cause of transportation accidents), to discuss the details of the accident and the ensuing fire. Following these discussions, the USNRC assembled a team of experts from the National Institute of Standards and Technology (NIST), the Center for Nuclear Waste Regulatory Analyses (CNWRA), and ...

National Aeronautics and Space Administration (NASA)

Rocker Peter Frampton and his band are introduced by astronaut Ron Garan to Commander Mike Fossum and Flight Engineers Satoshi Furukawa and Sergei Volkov aboard the International Space Station during a visit to Mission Control in Houston.

Science.gov (United States)

funded these sensors as the first Discovery Mission of. Opportunity, part of the ... aboard a Russian Soyuz rocket. .... the Swedes on other projects, mainly sounding rocket projects. ..... incoming applications for the Fellowship Program, fielding ...

Energy Technology Data Exchange (ETDEWEB)

In recent years, there has been increasing demand for resource-recycling of waste plastic, especially due to the introduction of legislation on recycling of materials used for packages of household goods. Methods of recycling waste plastic from household goods are currently still under development, and appropriate techniques to deal with such waste are required. Toshiba has developed a technique to dehydrochlorinate plastic containing polyvinyl chloride (PVC). This paper introduces our petrolization and dehydrochlorination system for waste plastic containing PVC. (author)

Energy Technology Data Exchange (ETDEWEB)

Volume VI of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the groundwater flow model data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.

Energy Technology Data Exchange (ETDEWEB)

Volume II of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the potentiometric data. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.

Energy Technology Data Exchange (ETDEWEB)

This bibliography contains citations concerning the recycling of scrap plastic produced in the injection-molding process. Plastic pellets made from scrap that are used in the injection-molding process are also discussed. Recycling equipment and automated recycling systems are described. Ways to utilize plastic scrap from used cars, packaging materials, and waste from polyurethane production are presented. (This updated bibliography contains 116 citations, 14 of which are new entries to the previous edition.)

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning the recycling of scrap plastic produced in the injection molding process. Plastic pellets made from scrap, that are used in the injection molding process, are also discussed. Recycling equipment and automated recycling systems are described. The reuse of plastic scrap culled from junk automobiles and packaging materials is discussed, and waste byproducts from polyurethane production are described. (Contains 50-250 citations and includes a subject term index and title list.) (Copyright NERAC, Inc. 1995)

International Nuclear Information System (INIS)

Effects of #gamma#-irradiation on synthetic polymers and paper used as packaging materials for irradiated food have been studied by NMR. Polystyrene, polybutadiene and some copolymers were studied before and after the #gamma#-irradiation treatment and in the presence or absence of antioxidants and stabilisers. In the absence of additives, the effect of #gamma#-irradiation on polystyrene is negligible even irradiating at high doses. In turn, the role of antioxidants and stabilisers is crucial in polybutadiene and butadiene-containing copolymers. Wood pulp paper was also studied by NMR. Preliminary measurements on #gamma#-irradiated wood pulp sheets show a shortening in the T_2 relaxation time component due to the bound water, i.e. some of the bound water is lost. (author)

International Nuclear Information System (INIS)

Studies were made on different types of packaging materials used for packing dried fish in the Philippines with a view to finding a suitable packaging material for irradiated dried fish. Among these packaging materials (polyethylene, cello/polyethylene, polyester/polyethylene, Kraft paper, polypropylene and interwoven polypropylene sacks), polyester/polyethylene laminate was the most resistant material against penetration by Dermestes carnivorous. No insect damage occurred on the dried fish packed in interwoven polypropylene lined with polyester/polyethylene laminate. The cost per sack of such packaging material having a capacity of 50-80 kg is US$ 0.50. The sack lined with polyester/polyethylene proved to be durable for surface transportation from Bacolod City to Manila (approx. 360 miles). Radiation treatment at 225 krad was effective against bacterial contamination but not effective in inhibiting ...

Energy Technology Data Exchange (ETDEWEB)

Sandia was presented with an opportunity in 1993 to design containers for the long term storage and transport of fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory which were tasked with developing the internal fixturing for the contents. The hardware is being supplied by Allied Signal Federal Manufacturing and Technologies, and the packaging will occur at Mason and Hangar Corporation`s Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required not only a rigorous design capable of meeting the long term storage and transportation requirements, but also resulted in ...

Science.gov (United States)

Aluminum electrolytic capacitors are presently not allowed on NASA missions because they outgas water and organic vapors, as well as H2. As a consequence, much larger and heavier packages of tantalum capacitors are used. A hermetically sealed aluminum capacitor has been developed under NASA-MSFC SBIR contracts. This capacitor contains a nongassing electrolyte that was developed for this application so internal pressure would remain low. Capacitors rated at 250 to 540 V have been operated under full load for thousands of hours at 85 and 105 C with good electrical performance and low internal pressure. Electrolyte chemistry and seal engineering concepts will be discussed.

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning waste treatment and disposal in the food processing industry. Methods, equipment, and technology are considered. References discuss waste heat recovery and examine treatment of wastes resulting from meat and seafood processing, dairy and beverage production, and fruit and vegetable processing. The citations explore conversion of the treated waste to fertilizer and for use in animal feeds, combustion for energy production, biogas production, and composting. The recovery and recycling of usable chemicals from the food waste are also covered. Food packaging recycling is considered in a related bibliography. (Contains 250 citations and includes a subject term index and title list.)

Energy Technology Data Exchange (ETDEWEB)

Volume III of the documentation for the Phase I Data Analysis Task performed in support of the current Regional Flow Model, Transport Model, and Risk Assessment for the Nevada Test Site Underground Test Area Subproject contains the data covering groundwater recharge and discharge. Because of the size and complexity of the model area, a considerable quantity of data was collected and analyzed in support of the modeling efforts. The data analysis task was consequently broken into eight subtasks, and descriptions of each subtask's activities are contained in one of the eight volumes that comprise the Phase I Data Analysis Documentation.

British Library Electronic Table of Contents (United Kingdom)

To eliminate their classical brittleness and flexibility problems zein films were plasticized by incorporation of different phenolic acids (gallic acid (GA), p-hydroxy benzoic acid (HBA) or ferulic acids (FA)) or flavonoids (catechin (CAT), flavone (FLA) or quercetin (QU)). The use of GA, CAT, FA and HBA at 3 mg/cm2 eliminated the brittleness of films and gave highly flexible films showing elongations between 135% and 189%, while FLA and QU caused no considerable effect on film elongation. The films containing FA and HBA showed extreme swelling and lost their structural integrity when hydrated in distilled water. In contrast, CAT and GA containing films maintained their integrity following hydration. Most of the GA (up to 93%) and a considerable portion of CAT (up to 60%) in the films exis...

British Library Electronic Table of Contents (United Kingdom)

Summary In this study, antimicrobial activity of zein films incorporated with partially purified lysozyme and disodium ethylenediaminetetraacetic acid (Na2EDTA) has been tested on selected pathogenic bacteria and refrigerated ground beef patties. The developed films containing 700-g-cm-2 lysozyme and 300-g-cm-2 Na2EDTA showed antimicrobial activity on Listeria monocytogenes, Escherichia coli O157:H7, and Salmonella typhimurium. The application of lysozyme and Na2EDTA incorporated zein films on beef patties significantly decreased total viable counts (TVC) and total coliform counts after 5-days of storage compared to those of control patties (P-2EDTA or Na2EDTA alone significantly slowed down the oxidative changes in patties during storage (P-P-2EDTA for active packaging of refrigerated mea...

Science.gov (United States)

D.1 PACKAGING AND MARKING (NASA 18-52.210-75) (SEP 1990) ... Packaging, Handling, and Transportation, and/or MIL-STD-2073-1 and MIL-STD- 2073-2, ...

International Nuclear Information System (INIS)

Requirements for food packaging materials include whether there is any interaction between the food and the package during or after the irradiation, and whether as a result of the irradiation, volatile or leachable substances are released from the pack into the food. The performance of cellulose-based materials and plastic films under irradiation are discussed.

International Nuclear Information System (INIS)

This paper reports about in-situ corrosion studies on selected materials for long-term resistant high-level waste (HLW) packagings acting as a barrier in a rock salt repository. The materials (Ti 99.8-Pd, Hastelloy C4 and five iron-base materials) were investigated in heated boreholes in the Asse salt mine under simulated HLW disposal conditions prevailing in normal operation of repository and in certain accident scenarios. The experiments under normal operating conditions were performed at temperatures of 120 deg. C to 210 deg. C (vertical temperature profile in the boreholes) without and with gamma irradiation (3#centre dot#10"2 Gy/h, Co-60 source) within the framework of the German/US Brine Migration Test. In these experiments only small amounts of migrated brine inclusions (NaCl-rich) from the rock salt were present as corrosion medium. In the experiments carried out under simulated accident conditions with intrusion of larger amounts of NaCl brine into the HLW ...

Energy Technology Data Exchange (ETDEWEB)

First, the problem of food packaging waste is introduced and one of the solutions, the Tetra Pak, is completely described. The article highlights the political sensitivity concerning the landfilling of packaging waste, as is done with the efforts of the Tetra Pak producer concerning the collection of used Tetra Paks and the results of these efforts. The document also informs us about the different recycling options for Tetra Paks, the qualitative prevention (using cleaner packaging), the quantitative prevention (using less packaging) and the sustainable development (using loner lasting packaging). The proposed four-step plan for a communication strategy is company-specific.

Energy Technology Data Exchange (ETDEWEB)

This manual is intended to serve several purposes. The first goal is to describe the capabilities and operation of the SMC processor package from an operator or user point of view. Secondly, the manual will describe in some detail the basic hardware elements and how they can be used effectively to implement a step motor control system. Practical information on the use, installation and checkout of the hardware set is presented in the following sections along with programming suggestions. Available related system software is described in this manual for reference and as an aid in understanding the system architecture. Section two presents an overview and operations manual of the SMC processor describing its composition and functional capabilities. Section three contains hardware descriptions in some detail for the LLL-designed hardware used in the SMC processor. Basic theory of operation and important features are explained.

International Nuclear Information System (INIS)

Peculiarities of Kurchatov Institute WWR-2 and TR research reactors spent fuel treating and transportation for radiochemical processing are stated. Spent fuels were performed as fuel assemblies of different forms and containing similar fuel elements: EhK-10 with 10% enrichment UO2-Mg fuel kernels or S-36 with 36% enrichment U-Al alloys. Spent fuel storage conditions are described. Features of developed procedures for identification of fuel assemblies by type of fuel elements are given. Transport package TUK-19 for loading and transportation of spent fuel for processing was chosen. Details of spent fuel loading in TUK-19 that is conducted by personnel under protective sheet of water in special reclaim volume are described

British Library Electronic Table of Contents (United Kingdom)

Fresh and fresh-cut tomatoes have been associated with numerous outbreaks of salmonellosis in recent years. One effective post harvest treatment to reduce Salmonella enterica in tomatoes may be high pressure processing (HPP). The objectives of the study were to determine the potential for HPP to reduce S. enterica serovars Newport, Javiana, Braenderup and Anatum in tryptic soy broth (TSB) and to determine the effect of HPP to reduce the most pressure resistant of the four serovars from fresh diced and whole tomatoes. To evaluate pressure resistance, TSB containing 8 log CFU/ml of one of the four serovars was packaged in sterile stomacher bags and subjected to one of three different pressures (350, 450 or 550MPa) for 120s. The most pressure resistant S. enterica serovar evaluated was Braend...

British Library Electronic Table of Contents (United Kingdom)

Cellulose sausage cellulose casings are used extensively in the manufacture of sausages in meat packaging. After stripping the meat, spent casings mainly contain cellulose and residual meat juice with salt, nitrate and nitrite. Disposal of spent sausage casings has serious economic and environmental concerns for the sausage industry. This work describes bioconversion of spent cellulose casings (SCC) into enzymes, lactic acid and ethanol by using cellulolytic fungi, lactobacillus and yeasts. The solid substrate cultivation (SSC) of Trichoderma reesei RUT C-30 on SCC and blends gave a maximum of 152 filter paper cellulase (FPase) activity and about 100 carboxymethylcellulase activity (CMCase)/g dry weight substrate. The SSC produced enzyme-rich casing with 50 FPase when directly mixed as suc...

Science.gov (United States)

... of Packaging Requirements. MIL-STD-2073-1 DoD Packaging Data Forms Instruction for Preparation and Use. I DATA ...

International Nuclear Information System (INIS)

... EFFECT OF GAMMA RADIATION AND BAG PACKAGING MATERIALS ON

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

CERN Document Server

Data from the power output of the radioisotope thermoelectric generators aboard the Cassini spacecraft are used to test the conjecture that small deviations observed in terrestrial measurements of the exponential radioactive decay law are correlated with the Earth-Sun distance. No significant deviations from exponential decay are observed over a range of 0.7 - 1.6 A.U. A 90% Cl upper limit of 0.84 x 10^-4 is set on a term in the decay rate of Pu-238 proportional to 1/R^2 and 0.99 x 10^-4 for a term proportional to 1/R.

Wastenet

...it only highlights the different feedstocks used in the production of fiber-based packaging materials or fossil-fuel ones; what about the energy required to convert ...feedstock, is unacceptable in trying to quantify the overall burden a specific packaging material has on the environment. As an aside, the point ... Consequentially, it is difficult to speculate on how much packaging material a company diverts from the landfill by switching from one material to another ...without specifying what geographical region said packaging material resides in. In addition, there is a lot of interest in diverting PET thermoforms from ...

Energy Technology Data Exchange (ETDEWEB)

Radioactive wastes are generally classified into 3 type depending on their physical property: liquid, solid and gaseous type. State-of -the art concerning liquid waste treatment has already been published; KAERI/TR-1315/99. Solid wastes classification package and treatment method will be studied to effectively manage them during the practical decommissioning work. All of the spent fuel produced during the operation of the TRIGA Mark-2 and 3 have been transported to the US last year, 1998, according to the spent fuel management strategy set-up by the US government for the non-proliferation of nuclear energy. Solid wastes are mainly all equipment existing inside of the reactors, activated concrete among the bio-shielded concrete, pipes, pimps, resin filter and it's housings, heat-exchangers, liquid waste storage tanks, to radioactive waste storage treatment facilities and so on. Solid wastes are generally low-level. They are classified according to the ...

International Nuclear Information System (INIS)

Various types of nuclear power plants are being constructed and operated in Korea, and in terms of regulatory control, a method of examining and evaluating the structural integrity of containment structure is being used. Generally, after the construction has been completed, all containment structure go through a Structural Integrity Test(hereinafter SIT) in which the displacement occurring in a structure under greater internal pressure than it was designed for is measured and the result is comparatively assessed with the allowed criteria. Most of the nuclear power plants in Korea are American type plants and their SIT uses the Invar-wire and Extensometer methods. These existing methods are expected to be used for the APR1400 plant currently being built unless some other reliable alternative technique is presented. This tendency can be observed in other countries, such as Japan, and there is thus insufficient effort to enhance the reliability of ...

International Nuclear Information System (INIS)

The aim of this work was to develop several strategies and software-packages for the evaluation of in-vivo-data of the human brain, which were acquired with high-resolution 1H-MRSI at 1.5 and 3 T. Several studies involving phantoms, volunteers and patients were performed. Quality assurance studies were conducted in order to evaluate the reproducibility of the applied MR-techniques at both field strengths. A qualitative comparison-study between MRSI-data from a 1.5 T clinical MR-scanner and a 3 T research MR-scanner showed the advantages of the more advanced MRSI sequences and higher field strength (3 T). A study involving patients with primary brain tumours (gliomas) was performed in cooperation with the Department of Neurosurgery (University of Erlangen-Nuremberg). The methods developed in the course of this study, such as the integration of MRS-data into a stereotactic-system, the segmentation of metabolic maps and the correlation with histopathological findings ...

Energy Technology Data Exchange (ETDEWEB)

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and ...

Wastenet

... Database listings you may be interested in: 3rd Party Reviewed Listings Sustainable Industrial Paper Strap - Natural & White High strength, sustainable, recyclable paper strap SDF Strapping, Inc. High Graphics Litho Lam Corrugated High Graphics Corrugated Packaging (Litho-Lam) Accurate Box Company, Inc. EcoSystem Packaging Solution Starch-based loosefill packing peanut system StarchTech GreenChoice 100 100% recycled, clay-coated paperboard Strathcona Paper, L.P. Greener Package Database! comprehensive sustainability data on packaging materials searchable by converted package or raw material standardizes reporting of sustainability claims many ...

British Library Electronic Table of Contents (United Kingdom)

The concept of antimicrobial packaging has received great attention because of its potential to enhance food safety. Several studies have explored its applications and effectiveness to suppress pathogenic microorganisms. However, few studies have analyzed the alterations caused in the engineering properties of food-packaging polymers after the incorporation of antimicrobials. Such information is very important to understand the feasibility of producing antimicrobial packaging films on the industrial scale. This review explores the work done so far to evaluate how the incorporation of antimicrobial substances affects the properties of food-packaging systems. This article also emphasizes diffusion studies on antimicrobial substances through packaging films and the analytical solutions used t...

International Nuclear Information System (INIS)

Radiation decontamination of dry ingredients, herbs and enzyme preparations is a technically feasible, economically viable and safe physical process. The procedure is direct, simple, requires no additives and is highly efficient. Its dose requirement is moderate. Radiation doses of 3-10 kGy (0.3-1 mrad) have proved sufficient to reduce the viable counts to a satisfactory level. Ionising radiations do not cause any significant rise in temperature. The flavour, texture or other important technological or sensory properties of most ingredients are not influenced at radiation doses necessary for satisfactory decontamination, and radiation obviates the chemical residue problem. The microflora surviving radiation decontamination of dry ingredients are more susceptible to subsequent antimicrobial treatments. Recontamination can be prevented as the product can be irradiated in its final packaging. Irradiation could be carried out in commercial ...

International Nuclear Information System (INIS)

Decomposition of organic compounds contained in the spent ion exchange resins is considered effective in reducing the waste volume. A system using the wet-oxidation process has been studied for the treatment of the spent resins stored at Trino Nuclear Power Plant owned by SOGIN. Compared with various processes for treating sludge and resin, the wet-oxidation system is rather simple and the process conditions are mild. Not contaminated ion exchange resin samples similar to those ones used in Trino NPP were processed by wet-oxidation and appropriate decomposition of the organic compounds was verified. After decomposition the residue can be solidified with cement for final disposal. When compared with direct solidification without decomposition, the number of waste packages can be significantly reduced. Additional measures for conditioning secondary waste products have also been studied, and their applicability to the Trino Nuclear Power Plant was ...

UK PubMed Central (United Kingdom)

Assembly of infectious adenovirus particles requires seven functionally redundant elements at the left end of the genome, termed A repeats, that direct packaging of the DNA. Previous studies revealed...Full Text Available

International Nuclear Information System (INIS)

This guide describes an acceptable method of complying with the Commission's regulations with regard to the quality assurance requirements for the packaging, shipping, receiving, storage, and handling of items for water-cooled nuclear power plants.

Science.gov (United States)

... the provisions of NASA Handbook (NHB) 6000.1, Requirements for Packaging, Handling, and Transportation, and/or MIL-STD-2073-1 and MIL-STD-2073-2, ...

UK PubMed Central (United Kingdom)

The RNA packaging process for retroviruses involves a recognition event of the genome-length viral RNA by the viral Gag polyprotein precursor (PrGag), an important step in particle morphogenesis. The...Full Text Available

Science.gov (United States)

... These requirements may be expressed in terms of MIL-STD-2073-1, DoD Material Procedures for Development and Application of Packaging ...

International Nuclear Information System (INIS)

In view of the interest in the use of gamma irradiation to extend the storage life of pre-packaged foods a report is made on the effects of gamma radiation on the migration of Irganox 1076 and Irganox 1010, antioxidants present in food packaging plastics, into synthetic triglyceride fatty-food simulant HB307 and iso-octane. The extent of migration was assayed by h.p.l.c. techniques. Migration into HB307 and iso-octane decreased steadily as irradiation progressed suggesting that gamma irradiation of packaging materials helps to prevent the contamination of food by antioxidants in the packaging. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

MINEQL is a subroutine package to calculate equilibrium composition of an aqueous system, accounting for mass transfer.

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

When solidified products made from low-level radioactive waste with melting treatment are disposed of in near surface repositories, concentrations of the radionuclides contained in the waste package have to be evaluated. Americium-242m is one of the targeted nuclides. In this study, simple analytical methods to evaluate the activity of "2"4"2"mAm are studied. Americium, Cm and Eu in a sample solution made from simulated solidified product and tracer of "1"5"2Eu and "2"4"4Cm and unknown solution of "2"4"1"+"2"4"2"m"+"2"4"3Am were separated from matrix elements with TRU resin. The fraction containing Eu, Am and Cm was passed through pyridine resin to separate Am from Eu and Cm. The contamination factor of "2"4"4Cm/"2"4"1Am was less than 3.0x10"-"3. Curium-242 generated from "2"4"2Am was measured to evaluate the activity of "2"4"2"mAm. The fraction containing Eu, Am and Cm was also passed through TEVA ...

Energy Technology Data Exchange (ETDEWEB)

Corrosion is a primary determinant of waste package performance at the proposed Yucca Mountain Repository and will control the delay time for radionuclide transport from the waste package. Corrosion is the most probable and most likely degradation process that will determine when packages will be penetrated and the shape, size, and distribution of those penetrations. The general issues in corrosion science, materials science and electrochemistry are well defined, and the knowledge base is substantial for understanding corrosion processes. In this paper, the Yucca Mountain Repository is viewed from a corrosion perspective. A major component of the long-term strategy for safe disposal of nuclear waste at the Yucca Mountain Repository is first to completely isolate the radionuclides in the waste packages for long times and to greatly retard the egress and transport of radionuclides from penetrated ...

International Nuclear Information System (INIS)

The development of Callossobruchus chinensis (L.) in different packaging materials were conducted with gram and lentil seeds under control temperature. The highest population rise was recorded in laminated jute bags and the weight loss of gram increased with the increase of the number of insects. A doses of 0.1 kGy inhibit all metamorphic stages of the beetle. The use of appropriate packaging materials can reduce the risk of re infestation in the post-irradiated food items. 9 refs., 1 fig., 2 tables (author).

Energy Technology Data Exchange (ETDEWEB)

This paper reports the development of a relay coordination package specially designed as a teaching aid. Fault studies required for relay coordination has been performed by using a newly developed loop impedance matrix. This new method of forming loop impedance matrix is particularly suitable for multiple fault studies environment as required in relay coordination. A simple topology searching technique has been used to find all loops of the network. This package simultaneously serves the purpose of teaching relay coordination, loop analysis technique and the method of topology searching.

Science.gov (United States)

5.2 Network Security. The features listed below can be used to help safeguard UNIX ...... The LaRCSCAN non-intrusive network security scanner package, ...

Energy Technology Data Exchange (ETDEWEB)

Oestfold Research has trough the project 'Climate accounts for disposal' for Waste Norway developed a model for calculation of net greenhouse gas emissions at the disposal of various waste types. The model is based on life cycle methodology according to the standard IS014044. This model has been used for plastic packaging in the project by adapting the basic values of specific conditions in the municipality of Fredrikstad. Oestfold Research has made an assessment of greenhouse gas emissions for the recycling and material recovery of plastic packaging from households in the district on assignment from Fredrikstad municipality and compared with the current solution where plastic packaging together with residual waste is used for energy utilisation. Based on the population in Fredrikstad and estimated amount of plastic packaging waste arising per household per year the difference in ...

Science.gov (United States)

... 9 SIMPLIFICATION STUDY RECOMMENDATIONS - MIL-STD-2073-1/2 ... SIMPLIFICATION STUDY RECOMMENDATIONS - MIL-STD-2073-1/2 ...

Science.gov (United States)

... (Metric) 80 Page 24. MIL-HDBK-263B MIL-STD-2073-1 - DOD Materiel Procedures for Development and Application of Packaging Requirements. ...

International Nuclear Information System (INIS)

Poly(lactic acid) (PLA) is attractive as a substitute for classical polymer packaging material due to its biodegradability and sufficient mechanical and barrier properties. Presented research was focused on the changes of basic mechanical parameters after ionizing irradiation performed with doses in the range of 2.5-25 kGy, commonly used in radiation sterilization and preservation of foods. Two commercial available PLA packaging films were tested. The influence of radiation dose on the mechanical properties - tensile strength and elongation were determined using standardized methods. Radiation resistance of PLA is sufficient for packaging applications. The investigations of gas products of radiolysis of PLA have been made by gas chromatography after electron beam (EB) irradiations. (authors)

International Nuclear Information System (INIS)

English 2000 p. 91 Brazil Saiki, M. Kamiya, AM Nomura, DH Mateus,

International Nuclear Information System (INIS)

Full text: There are following general tendencies linking to SNF and radioactive waste management (RWM) in the Russian nuclear industry now. The intention to use the closed nuclear fuel cycle based on power water reactors and fast reactor. The intensification of measures aimed at the solution of 'nuclear legacy' from defenses programs of USSR. The intention to improve the existing national RW management infrastructure in the near years by means of the creation of a centralized national system (including managing corporation responsible for operation of long-storage and disposal facilities of conditioned RW). The main aims radioactive waste management (RWM) in nuclear power plants (NPP) for the next 10-15 years are to equip all NPPs with the necessary set of facilities for conditioning of the stored and currently generated RW with packaging the end-product into containers, to build regional NPPs RW repositories and to introduce evaporator ...

International Nuclear Information System (INIS)

We have constructed a Monte Carlo generator (the corresponding FORTRAN code can be obtained from the authors upon request) for lowest-order predictions for the processes #gamma##gamma##->#4f and #gamma##gamma##->#4f#gamma# in the standard model and extensions thereof by an effective #gamma##gamma#H coupling as well as anomalous triple and quartic gauge-boson couplings. Polarization is fully supported, and a realistic photon beam spectrum can be taken into account. For the processes #gamma##gamma##->#4f all helicity amplitudes are explicitly given in a compact form. The presented numerical results contain, in particular, a survey of cross sections for representative final states and their comparison to results obtained with the program package Whizard/Madgraph. The impact of a realistic beam spectrum on cross sections and distributions is illustrated. Moreover, the size of various contributions to cross sections, such as from weak ...

Energy Technology Data Exchange (ETDEWEB)

Current European and the US experiences in waste management are reviewed in the perspective of sustainable development. This publication questions the validity of the current approach taken by the Germany at ``closing the loop`` based on the example of packaging and packaging waste. The product item focus of current German legislation is compared with Danish and US approaches that are based on an integrated policy which covers the whole of waste generation and handling and is not product/item oriented. 1 fig., 2 tabs.

British Library Electronic Table of Contents (United Kingdom)

The K 2010 exhibition saw the introduction of PolyOne Corps OnCap Antifog Additive for polypropylene (PP) films, the first such additive for PP films that does not require corona treatment. According to the company, this new additive simplifies production of antifog films for the flexible food packaging industry, improving production efficiencies for both cast and blown film producers.

CERN Document Server

An update of the ODEtools Maple package, for the analytical solving of 1st and 2nd order ODEs using Lie group symmetry methods, is presented. The set of routines includes an ODE-solver and user-level commands realizing most of the relevant steps of the symmetry scheme. The package also includes commands for testing the returned results, and for classifying 1st and 2nd order ODEs.

Science.gov (United States)

...j-3/j-3311/DLAD/rev5.htm ), and MIL-STD-2073-1, Standard Practice for Military Packaging (and...Guidelines will comply with DLAD 47.305-1, and MIL-STD-2073-1. (f) Delays in delivery caused by...

Energy Technology Data Exchange (ETDEWEB)

Hard X-ray/gamma-ray spectrometers aboard two interplanetary spacecraft, Ulysses and Pioneer Venus Orbiter (PVO), and two near-Earth spacecraft, Yohkoh and Compton Gamma Ray Observatory (GRO/BATSE), are currently in operation. A unique set of circumstances have permitted the observation of the 15 November 1991 (2238 UT) flare by all the four instruments. This intense flare (GOES class X 1.5) was associated with the bright (3B) H-alpha flare located on the disk (S13, W19) in the active region 6919. At the time of the flare, the Ulysses and PVO spacecraft were located respectively 101[degree] and 52[degree] west of the Sun-Earth line. Thus the view angles for the PVO and Ulysses instruments were quite different from those of the near-Earth instruments on GRO and Yohkoh. The preliminary photon energy spectra observed by the four instruments at different times during the flare will be presented and their implications regarding the directivity of hard X-ray sources in ...

CERN Document Server

We present the general properties of the far-ultraviolet (FUV; 1370-1720A) continuum background over most of the sky, obtained with the Spectroscopy of Plasma Evolution from Astrophysical Radiation instrument (SPEAR, also known as FIMS), flown aboard the STSAT-1 satellite mission. We find that the diffuse FUV continuum intensity is well correlated with N_{HI}, 100 $\\mu$m, and H-alpha intensities but anti-correlated with soft X-ray. The strongest correlation is with the H-alpha emission, and the correlation of the diffuse background with the direct stellar flux is weaker than the correlation with other parameters. The continuum spectra are relatively flat. However, a weak softening of the FUV spectra toward some sight lines, mostly at high Galactic latitudes, is found not only in direct-stellar but also in diffuse background spectra. The diffuse background is relatively softer that the direct stellar spectrum. We also find that the diffuse FUV background averaged ...

Energy Technology Data Exchange (ETDEWEB)

Under the repository storage conditions of Eram and Konrad, waste packages designed for permanent storage must not contain or release freely mobile liquids, except for the minimum residues attainable by reasonable efforts or unavoidable. In accordance with a directive issued by the German Federal Ministry for the Environment (BMU), waste conditioning must be carried out so as to minimize waste volumes and, if possible, on the site where the waste arises. Liquid waste is conditioned most effectively by drying. At the present time, various different processes for drying liquid waste are employed as reflected by the state of the art: The Robe process; roller drying; the RDA process; Favorit; in-drum drying; and HPA liquid waste drying with make-up feed. The HPA process offers these advantages: Drying under atmospheric conditions, which means high level of dryness (freely mobile and releasable water is removed); the residual water content is 10%; ...

International Nuclear Information System (INIS)

1 - Description of program or function: The COOLOD-N2 code provides a capability for the analyses of the steady-state thermal-hydraulics of research reactors. This code is a revised version of the COOLOD-N code, and is applicable not only for research reactors in which plate-type fuel is adopted, but also for research reactors in which rod-type fuel is adopted. In the code, subroutines to calculate temperature distribution in rod-type fuel have been newly added to the COOLOD-N code. The COOLOD-N2 code can calculate fuel temperatures under both forced convection cooling mode and natural convection cooling mode. A 'Heat Transfer package' is used for calculating heat transfer coefficient, DNB heat flux etc. The 'Heat Transfer package' is a subroutine program and is especially developed for research reactors in which plate-type fuel is adopted. In case of rod-type fuel, DNB heat flux is calculated by both the 'Heat Transfer ...

International Nuclear Information System (INIS)

Joint FAO/IAEA/WHO Expert Committee approved the use of radiation treatment of foods. Nowadays food packaging are mostly made of plastics, natural or synthetic, therefore effect of irradiation on these materials is crucial for packing engineering for food irradiation technology. By selecting the right polymer materials for food packaging it can be ensured that the critical elements of material and product performance are not compromised. When packaging materials are in contact with food at the time of irradiation that regulatory approvals sometimes apply. The review of the R-and-D and technical papers regarding material selection, testing and approval is presented in the report. The most information come from the USA where this subject is well elaborated, the International Atomic Energy Agency (IAEA) reports are reviewed as well. The report can be useful for scientists and food irradiation plants operators. (author)

International Nuclear Information System (INIS)

The effect on human health of using food packaging made from recycled materials will depend on whether the elements will migrate into the food itself and at which levels that would be of concern. There is no EU directive for paper and board packaging, but guidelines on paper and board intended to come into contact with food are being developed in another forum. These do not propose limits for paper intended to come into contact with dry foods. However, for other foodstuffs, restriction limits in paper of 0.002 mg/dm"2 (Cd), 0.003 mg/dm"2 (Pb), and 0.002 mg/dm"2 (Hg) have been proposed. This paper describes a radiotracer method that has been applied to the determination of migration of trace elements from paper and board into real food samples.

British Library Electronic Table of Contents (United Kingdom)

The need for safe food products has motivated food scientists and industry to find novel technologies for antimicrobial delivery for improving food safety and quality. Controlled release packaging is a novel technology that uses the package to deliver antimicrobials in a controlled manner and sustain antimicrobial stress on the targeted microorganism over the required shelf life. This work studied the effect of controlled release of nisin to inhibit growth of Micrococcus luteus (a model microorganism) using a computerized syringe pump system to mimic the release of nisin from packaging films which was characterized by an initially fast rate and a slower rate as time progressed. The results show that controlled release of nisin was strikingly more effective than instantly added (?formulated...

Science.gov (United States)

... The genus Ipomea contains a species, Ipomea , which contains a purgative (Jl). Ipomea batatus is not known to contain this substance. ...

KoreaScience (Korea)

Full Text Available

CERN Document Server

Tree-level scattering amplitudes of longitudinally polarized electroweak vector bosons in the Standard Model are calculated using Mathematica package Feyncalc. The modifications of low-energy theorems for longitudinally polarized W and Z in the Standard Model are discussed.

UK PubMed Central (United Kingdom)

AbstractThe Galaxy package empowers regular users to perform rich DNA sequence analysis through a much-needed and user-friendly graphical web interface.See research article...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

An overview of the operations of Sandia`s Microelectronics Development Lab (MDL) is to develop radiation hardened IC, but techniques used for IC processing have been applied to a variety of related technologies such as micromechanics, smart sensors, and packaging.

UK PubMed Central (United Kingdom)

An interactive system for computer analysis of nucleic acid and protein sequences has been developed for the Los Alamos DNA Sequence Database. It provides a convenient way to search or verify various...Full Text Available

UK PubMed Central (United Kingdom)

A Staphylococcus strain was inoculated on the top and cut surfaces of freshly baked Southern custard pies which were then packaged in a pasteboard carton and held at 30 C. Daily plate...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundMicroarray data are often used for patient classification and gene selection. An appropriate tool for end users and biomedical researchers should combine user friendliness...Full Text Available

Science.gov (United States)

An experimental investigation of natural convection heat transfer from a commercially available semiconductor device package is presented. The package was centrally mounted on a ceramic substrate. The package-substrate assembly formed one surface of a dielectric-filled cubical enclosure of aspect ratio one. The top surface of the enclosure was maintained at prescribed temperature. Surface temperature measurements were made at various locations on the substrate, the package lid, as well as the chip center. These measurements are reported for three dielectric fluids and three enclosures top surface temperatures, both with the substrate oriented horizontally as well as vertically. The results indicate that the maximum input power without exceeding a chip junction temperature of 80 C is 2.58 watts with FC-75 as the cooling fluid and the upper boundary maintained at 15 C. This is significantly larger than ...

UK PubMed Central (United Kingdom)

In a cross-over study, participants (n=59) were randomly assigned to receive either 100 kcal packs or standard size packages of snacks for 1-week. After a minimum of a 1-week washout period,...Full Text Available

UK PubMed Central (United Kingdom)

Generation of replicative defective viruses is frequently observed during viral infections. We now report that encapsidation and reverse transcription of spliced viral RNA is an additional mechanism...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

During the course of a fiscal year, Oak Ridge National Laboratory`s Carbon Dioxide Information Analysis Center (CDIAC) distributes thousands of specialty publications-numeric data packages (NDPs), computer model packages (CMPs), technical reports, public communication publications, newsletters, article reprints, and reference books-in response to requests for information related to global environmental issues, primarily those pertaining to climate change. CDIACs staff also provides technical responses to specific inquiries related to carbon dioxide (CO{sub 2}), other trace gases, and climate. Hundreds of referrals to other researchers, policy analysts, information specialists, or organizations are also facilitated by CDIAC`s staff. This report provides an account of the activities accomplished by CDIAC during the period October 1, 1991 to September 30, 1992. An organizational overview of CDIAC and its staff is supplemented by a detailed ...

UK PubMed Central (United Kingdom)

The primary method for neuronal communication involves the extracellular release of small molecules that are packaged in secretory vesicles. We have developed a platform to separate, lyse, and...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Thermal desorption spectroscopy (TDS) was used to study outgassing from polycrystalline SiGe (poly-SiGe), SiC and SiO"2 films used for poly-SiGe-based MEMS thin film vacuum package technology. Primary desorption products were found to be H"2, H"2O and CO"2. The CO"2 outgassing could be correlated with CF"4 plasma interface cleaning used for thick SiGe PECVD, which can leave carbon at the CF"4-plasma-cleaned interface.

CERN Document Server

A shockproof container for the transport and storage of fragile or reactive target foils

International Nuclear Information System (INIS)

The changes in quality of irradiated spices, i.e., nutmeg (Myristica fragrans), black pepper and white pepper (Piper nigrum) stored in different indigenous packaging materials were evaluated. Packaging materials used were tin cans; tin can lined with polypropylene film, tin can lined with wrapping paper, woven polypropylene bag and woven polypropylene bag lined with polypropylene film. Packaging in woven polypropylene bag could cause significant changes in a_w-values and moisture contents of the spices. In the tin can, no significant change was found during storage. By applying a polypropylene film liner inside the plastic bag, the changes could be retarded. The other parameters observed, i.e. total plate count, total mould and yeast count and organoleptic scores of the samples were not significantly affected by the packaging method. A dose of 5 kGy could reduce the microbial load of the spices by about ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Salmonella Typhimurium and Listeria monocytogenes are major bacterial pathogens associated with poultry products. A controlled released ClO2 sachet applied with modified atmosphere packaging (MAP) was evaluated for its ability to control the growth of S. Typhimurium and L. monocytogenes on raw chicken breast during refrigerated storage. The fresh chicken samples were inoculated with one or the other of the pathogens at 104-cfu/g, and the packages (with and without ClO2 sachet) were flushed with ambient air or 30% CO2/70% N2 before sealing, and then stored at 4C for up to 21 days. The maximum reduction in MAP plus ClO2 (compared with MAP alone) was 0.68-log-cfu/g for S. Typhimurium and 1.87-log-cfu/g for L. monocytogenes. Color and pH changes of the chicken breast were observed at ...

Energy Technology Data Exchange (ETDEWEB)

The PuO/sub 2/ cask or SP 5320-2 and 3 cask is designed for surface shipment of americium or plutonium. The cask design was physically tested to demonstrate that it met the criteria specified in US ERDA Manual Chapter 0529, and Chapter I, Interstate Commerce Commission. The package has been assessed for transport of up to 357 grams of plutonium (403 grams PuO/sub 2/ powder) and up to 176 grams of americium (200 grams AmO/sub 2/ powder), having a maximum decay heat of 203 watts. Criticality evaluation alone would allow the shipment as Fissile Class II but the radiation level of the cask, measured at the time of shipment, may exceed 50 mrem/h at the surface and require shipment as Fissile Class III. Sample calculations address only the more restrictive of the two materials, which in most cases is /sup 238/PuO/sub 2/.

Energy Technology Data Exchange (ETDEWEB)

Limited field trial results of a heating oil additive package developed to minimize unscheduled maintenance indicate that it achieves its goal of keeping heating oil systems cleaner. The multifunctional additive package was developed to provide improved fuel oxidation stability, improved corrosion protection, and dispersency. This combination of performance benefits was chosen because we believed it would retard the formation of sludge, as well as allow sludge already present to be carried through the system without fouling the fuel system components (dispersency should keep sludge particles small so they pass through the filtering system). Since many unscheduled maintenance calls are linked to fouling of the fuel filtering system, the overall goal of this technology is to reduce these maintenance calls. Photographic evidence shows that the additive package not only reduces the amount of sludge formed, but even removes ...

Energy Technology Data Exchange (ETDEWEB)

All of the project work since the previous report has been on Phase 2B tasks. Therefore, this quarterly progress report summarizes the period's activities in Engineering, Procurement and Civil Construction. Engineering is 95% complete, but revisions and changes are still being incorporated particularly in the Instrument and Electrical areas. Procurement has only valves 4 in. and above yet to order to complete all major items purchased. The scheduled material curve was based on the original estimate of the job. The projected curve reflects the previous month's estimate. Construction of civil work is proceeding according to schedule in the field. The initial bid packages for the Mechanical General Contractor portion of the work have been reviewed and evaluated. Order placement is scheduled for the end of July. The Electrical package is due back from the bidders on July 6. It requires additional evaluation by BSC and DSO and will ...

International Nuclear Information System (INIS)

Volatile compounds produced in flexible food packaging materials (LDPE, EVAc, PET/PE/EVOH/PE) during electron beam irradiation were isolated by purge and trap technique and identified by combined gas chromatography-mass spectrometry (GC/MS), after thermal desorption and concentration. For comparison purposes non-irradiated films were also studied. Film samples were irradiated at low (5 kGy, corresponding to cold pasteurization), intermediate (20 kGy, corresponding to cold sterilization) and high (100 kGy) doses. It was observed that a number of volatile compounds are produced after irradiation in all cases. Furthermore the amounts of all volatile compounds increase with increasing irradiation dose. Both primary (methyl-derivatives etc.) as well as secondary i.e. oxidation products (ketones, aldehydes, alcohols, carboxylic acids etc.) are produced upon irradiation. These products may affect organoleptic properties and thus shelf-life of prepackaged irradiated foods. ...

Energy Technology Data Exchange (ETDEWEB)

The U.S. Department of Energy (DOE) Headquarters and associated contractors have developed an IBM PC-based software package that estimates costs, schedules, and public and occupational health risks for a range of mixed-waste management options. A key application of the software package is the comparison of various waste-treatment options documented in the draft Site Treatment Plans prepared in accordance with the requirements of the Federal Facility Compliance Act of 1992. This automated Systems Analysis Methodology consists of a user interface for configuring complexwide or site-specific waste-management options; calculational algorithms for cost, schedule and risk; and user-selected graphical or tabular output of results. The mixed-waste management activities modeled in the automated Systems Analysis Methodology include waste storage, characterization, handling, transportation, treatment, and disposal. Analyses of treatment options identified ...

Energy Technology Data Exchange (ETDEWEB)

The environments on the drip shield and waste package outer barrier are controlled by the compositions of the waters that contact these components. the temperature (T) of these components, and the effective relative humidity (RH) at these components. Because the composition of the waters that are expected to enter the emplacement drifts (either by seepage flow or by episodic flow) have not been specified: well J13 water was chosen as the reference water (Harrar 1990). Section 6.2 discusses the accessible RH for the temperatures of interest at the repository horizon. Section 6.3 discusses the adsorption of water on metal alloys in the absence of hygroscopic salts. Because the temperatures of the DSs and the WPOBs are higher than those of the surrounding near-field environment, the relative humidity at the DSs and the WPOBs will be lower than that of the surrounding near-field environment. This difference is a result of the water partial pressure in the drift being ...

International Nuclear Information System (INIS)

The influence of electron-beam irradiation on mechanical properties of commercial multilayer flexible packaging materials based on coextruded and laminated polypropylene (PP), low-density polyethylene (LDPE), ethylene vinyl alcohol copolymer (EVOH) and poly(ethylene terephthalate) (PET), irradiated with doses up to 120 kGy, was studied. The tensile strength and elongation at break of the irradiated PET/PP film increase, while the penetration and sealing resistance decreased. In addition, the irradiated PET/LDPE/EVOH/LDPE film presented increase in the tensile strength on some radiation doses and decrease of the penetration and sealing resistance, except for sealing resistance at radiation dose of 15 kGy that resulted in a slight increase of ca 4%.

International Nuclear Information System (INIS)

HLW disposal is one of the largest issue to utilize Nuclear power safely. In the past study, the concept, which buffer materials and Overpacked waste were transported into underground respectively, have shown. The concept of pre-assembled engineered barrier has advantage to simplify the logistics and emplacement procedure, however there are difficulties to support heavy weight of pre-assembled package by equipment under the condition of little clearance between tunnel and package. In this study, Combination of air bearing and two degree-of-freedom wheels were suggested for transportation, and air jack was suggested for unloading and emplacement system. Also, whole system for transportation and emplacement procedure was designed, and Scale model test was examined to evaluate the feasibility of these concept and functions. (author)

Energy Technology Data Exchange (ETDEWEB)

We report on the software aspects of the development of a switch-based data acquisition system at Fermilab. This paper describes how, with the goal of providing an ``integrated systems engineering`` environment, several powerful software tools were put in place to facilitate extensive exploration of all aspects of the design. These tools include a simulation package, graphics package and an Expert System shell which have been integrated to provide an environment which encourages the close interaction of hardware and software engineers. This paper includes a description of the simulation, user interface, embedded software, remote procedure calls, and diagnostic software which together have enabled us to provide real-time control and monitoring of a working prototype switch-based data acquisition (DAQ) system.

British Library Electronic Table of Contents (United Kingdom)

Abstract Microbiological quality and biophenol content evolution was studied in minimally processed Thassos cv table olives by hot air dehydration under mild conditions (40C, 24-h, aw-=-0.893) and storage under characteristic packaging conditions (vacuum, 100% N2 and air) at 4 and 20C over a period of 180 days. No salt was used in the production line or packaging. The undesirable microorganisms (Enterobacteriaceae, Staphylococcus aureus, Bacillus, Clostridium) were undetectable until the end of the storage period. Also, modified atmospheres prevented fungal growth at both temperatures apart from the samples stored in air, in which Penicillium and Aspergillus spp. were identified. At 20C, a coexistence of mesophilic bacteria and yeasts occurred. At 4C, yeasts were the predominant microflora...

Energy Technology Data Exchange (ETDEWEB)

Thin films of sodium montmorillonite clay and cationic polyacrylamide were grown on a polyethylene terephthalate film using layer-by-layer assembly. After 30 clay-polymer layers are deposited, with a thickness of 571 nm, the resulting transparent film has an oxygen transmission rate (OTR) below the detection limit of commercial instrumentation (< 0.005 cc/m{sup 2}/day/atm). This low OTR, which is unprecedented for a clay-filled polymer composite, is believed to be due to a brick wall nanostructure comprised of completely exfoliated clay in polymeric mortar. With an optical transparency greater than 90% and potential for microwaveability, this thin composite is a good candidate for foil replacement in food packaging and may also be useful for flexible electronics packaging.

CERN Document Server

The LHCb experiment has chosen to use the SAM framework (Service Availability Monitoring Environment from EGEE-II) [1] make extensive tests of the LHCb environment at all the accessible grid resources. The availability and the proper definition of the local Computing and Storage Elements, user interfaces as well as the WLCG software environment are checked. The SAM framework is also used to pre-install the LHCb applications in the shared software area provided by each site. The deployment of the LHCb applications is based on a python tool developed inside the experiment. It is used for software management including incremental installation of interdependent packages and clean package removal. After the application software is installed a validation test of the whole MC chain is run. According to the results of the experiment specific SAM tests, the sites are (re)integrated into the LHCb production system managed by DIRAC [2]. The possibility of ...

Energy Technology Data Exchange (ETDEWEB)

The analysis of transmission line faults is essential to the proper performance of the power system. It is required if protective relays are to take the appropriate action and in monitoring the performance of relays, circuit breakers, and other protective and control elements. The detection and classification of transmission line faults is a fundamental component of such fault analysis. Another application of fault analysis is in software packages for automated analysis of digital fault recorder (DFR) files. Recently, such a package, called DFR Assistant, was developed for substation applications. This program can be installed locally in a substation, in which case it is connected directly to the DFR via a high speed parallel link, or it can be installed at a central station, in which case it can be configured to automatically analyze events coming from all DFRs.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

then, the toroidal containment of charged plasmas by electric fields is comparable to the toroidal containment of neutral plasmas using the ...

Energy Technology Data Exchange (ETDEWEB)

A chemical equilibrium model is used, implemented in a compact FORTRAN package called HITEQ, to investigate possible mineral deposition related to prereinjection treatment of Cerro Prieto brines for silica removal. Large saturation ratios of the treated brines with respect to several minerals are indicated by these computations. As a remedy, an inexpensive CO/sub 2/ removal scheme aimed at inhibiting carbonate mineral precipitation is proposed. This scheme is quantitatively discussed with the aid of HITEQ. It is concluded that the proposed treatment is both technically and economically feasible.

Science.gov (United States)

Overview  Package   Class  Use  Tree  Deprecated  Index  Help   PREV CLASS   NEXT CLASS FRAMES    NO FRAMES SUMMARY:  INNER | FIELD | CONSTR | METHOD DETAIL:  FIELD | CONSTR | METHOD gov.nih.nci.dc.bean Class ImageIDParseBean java.lang.Object | +--java.util.Dictionary

Energy Technology Data Exchange (ETDEWEB)

The application of various signal processing methods to extract energy storage information from plasma diamagnetism sensors occurring during physics experiments on the Tandom Mirror Experiment-Upgrade (TMX-U) is discussed. We show how these processing techniques can be used to decrease the uncertainty in the corresponding sensor measurements. The algorithms suggested are implemented using SIG, an interactive signal processing package developed at LLNL.

Energy Technology Data Exchange (ETDEWEB)

Certification as applied to existing computer codes includes the verification and validation process, placing the code in configuration control, establishing user qualification standards and training requirements. All software intended for use in critical calculations must be certified. This report is intended to fulfill the requirements for the certification of the SHIELD, SHLDED, GEDIT, GENPRT, FIPROD, FPCALC, and PROCES modules of the SHIELD system built February, 1992, by W.S. Parks. These modules are used for burnup, cooling, separate, and edit calculations.

Energy Technology Data Exchange (ETDEWEB)

The Monsanto Chemical Company operates a plastics and resins plant located in Addyston, Ohio. The process equipment requires routine rinsing with technical grade acetone between batches. Due to the volumes of spent acetone generated and the associated RCRA hazardous waste regulations, the plant sought to recycle and reuse the acetone to reduce the purchase cost of virgin acetone and the cost of spent acetone disposal. One of the first options explored was package unit distillation units. The cost of these units was in the $20--$30,000 range in 1989 dollars. Even though the cost of a package unit was not deemed unreasonable, there were additional costs and concerns that led to elimination of this option. The unit would have required additional manpower to operate and maintain, i.e., at least a fraction of an operator and mechanic. For plant safety reasons, it was desired to operate this package unit outside the production ...

Energy Technology Data Exchange (ETDEWEB)

As a part of a phenomenological model, a method for simulating the wall/jet interaction in a direct injection diesel engine is proposed. The method is based on the application of the momentum conservation equation in the different directions in which the wall jet is spread, and takes into account both the interaction with the combustion chamber geometry and with swirl. It takes as initial conditions the results of calculating the free jet, which is divided into packages. The predictions provide good agreement with those by other researchers. (author).

Energy Technology Data Exchange (ETDEWEB)

This document describes testing of OSI products conducted at Argonne National Laboratory. Sun, IBM, and Clsco hardware platforms were used. Various software packages that implement file transfer and gateway applications were evaluated. The OSI model and GOSIP compliance are briefly discussed. Technical details on OSI addressing and routing are presented. The relationship of this testing to other OSI activities at Argonne and to activities of the national networking community is discussed. Mention is also made of the relationship of DECnet Phase V transition issues.

Wastenet

...and supply ensuring better food quality for the consumer developing safer and more flexible food production processes and technologies raw materials for food production; production and processing systems; by-products and wastes from fisheries and agro-industry; new food sources; packaging systems; quality monitoring; traceability Food contamination detecting and eliminating infectious and toxic agents throughout the food chain establishing the hazards and origins of food contaminants producing food more safely rapid ...

Energy Technology Data Exchange (ETDEWEB)

We report on the calculation of multi-loop Feynman integrals for single-scale problems by means of difference equations in Mellin space. The solution to these difference equations in terms of harmonic sums can be constructed algorithmically over difference fields, the so-called {pi}{sigma}{sup *}-fields. We test the implementation of the Mathematica package Sigma on examples from recent higher order perturbative calculations in Quantum Chromodynamics. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Characterization of the electron beam's properties will be a major task after the upgrade of the Los Alamos Free-Electron Laser (FEL) Facility with a photoelectric injector (PEI) and increased acceleration capability to 40 MeV. Adjustments to the previous diagnostics package that address the lower beam emittance, higher energy, and wakefield source reduction issues will be discussed. 6 refs., 8 figs., 1 tab.

UK PubMed Central (United Kingdom)

The halogenated benzimidazoles BDCRB (2-bromo-5,6-dichloro-1-β-d-riborfuranosyl benzimidazole riboside) and TCRB (2,5,6-trichloro-1-β-d-riborfuranosyl benzimidazole...Full Text Available

International Nuclear Information System (INIS)

The present report is final report from a study on characterisation of radioactive waters in the Nordic countries. The study has mainly been focused on long-lived low and intermediate level radioactive waste. Methods to measure or estimate the activity content and the general composition are discussed. Recommendations are given regarding characterisation of waste under treatment and characterisation of already produced waste packages. (au).

International Nuclear Information System (INIS)

The advance in the analysis of very small amount (<= 1#alpha#/cm"2h) of #alpha#-emitters in the cited materials is reviewed. The review, for which 75 references are listed, covers the period from January, 1978, to June, 1982. The use of #alpha#-ray counting, #alpha#-ray spectrometry, #gamma#-ray spectrometry, neutron activation analysis and mass spectrometry is discussed, and their relative merit and limitation are outlined. (J.P.N.).

International Nuclear Information System (INIS)

Hydroperoxides are important atmospheric oxidants. They are responsible for most of the oxidation of aqueous-phase SO(sub 2) to sulfate in the northeastern United States, resulting in the formation of acid precipitation and visibility-reducing sulfate aerosol (Penkett et al., 1979; Lind et al., 1987; Madronich and Calvert, 1990; Tanner and Schorran, 1995). Atmospheric hydrogen peroxide (H(sub 2)O(sub 2) or HP) is produced by the self-reaction of hydroperoxyl radicals (HO(sub 2)); higher organic peroxides are produced by reaction of HO(sub 2) with alkylperoxyl radicals (RO(sub 2)). Peroxyl radicals, along with OH, are chain carriers in the complex photochemical process that produces tropospheric ozone. Thus, concentrations of peroxides and their free radical precursors depend on solar intensity and ambient concentrations of water vapor, ozone, NO(sub x) (NO+ NO(sub 2)), and VOCs (volatile organic compounds). Several investigators have demonstrated that HP and hydroxymethyl hydroperoxide ...

Science.gov (United States)

The MISR instrument aboard NASA's Terra satellite participated in the UAE-2 campaign, August-October 2004. This campaign represented a unique opportunity to study the complex aerosol situation in the Arabian Gulf region, in the context of a first-rate collection of aircraft and surface-based instruments, giving us the opportunity to do some groundbreaking satellite aerosol validation work. We aimed (1) to validate MISR aerosol retrieval results for dust and pollution particles over dark and light surfaces, and (2) to contribute regional maps of aerosol optical thickness (AOT) and particle micro-physical properties, giving spatial context to the field-instrument measurements, and moving toward a satellite-based regional aerosol climatology. The validation effort benefited from the combination of an instrumented aircraft and a regional network of surface-based sun photometers. We obtained high-quality sub-orbital data coincident with MISR overpasses on three days: ...

Energy Technology Data Exchange (ETDEWEB)

Effect of nitrogen-containing additives in the study of wood plastic composites of MMA with simul and mango wood of Bangladesh has been investigated. Nine different additives were used and the additives containing carboamide group induce the highest tensile strength to the composite. (author).

Science.gov (United States)

Effect of nitrogen-containing additives in the study of wood plastic composites of MMA with simul and mango wood of Bangladesh has been investigated. Nine different additives were used and the additives containing carboamide group induce the highest tensile strength to the composite.

International Nuclear Information System (INIS)

This standard provides the general requirements used in the design, construction, testing, and commissioning of concrete containment structures for CANDU nuclear power plants designated as class containment and is directed to the owners, designers, manufacturers, fabricators, and constructors of the concrete components and parts.

Energy Technology Data Exchange (ETDEWEB)

The invention relates to a method for purifying a gas mixture containing at least one undesirable gas compound utilizing certain sulfonamide or sulfamide solvents.

Science.gov (United States)

... learn more about the thermal stability of InNP2 Me, a sample contained in a previously evacuated tube was heated at 100°C for 13 days. Neither ...

Energy Technology Data Exchange (ETDEWEB)

This invention relates to polyalkylenes which contain both halogen and ester groups, to the preparation thereof, and to the use thereof as pour depressants for fuel oils. This invention also relates to polyalkylene esters.

UK PubMed Central (United Kingdom)

Carboxylesterases (CE) are ubiquitous enzymes that hydrolyze numerous ester-containing xenobiotics, including complex molecules, such as the anticancer drugs irinotecan (CPT-11) and capecitabine...Full Text Available

International Nuclear Information System (INIS)

Description or function: WLUP contains validated WIMS-D formatted cross section libraries in 69 and 172 energy group structures for nuclear reactor calculations. Materials from recently released evaluated nuclear data libraries are included. The NJOY nuclear data processing system was applied for generating the cross section files following the models and conventions built into the WIMS-D lattice code. The relevant features for the WIMS users are: - Energy group structures: 69 and 172 energy groups. - List of materials: WIMS ID, general information, source of data. - Cross sections: 69 and 172 group plots. - Resonance data: WIMS ID, temperature, background cross sections. - Goldstein-Cohen factors: Goldstein-Cohen lambda values. - Thermal scattering data: thermal scattering laws and P1 matrixes. - Fission spectrum: fission spectrum data. - Burnup data: burnup chains. - Fission product yields: fission yield tables. - Pseudo lumped fission product: Description of ...

International Nuclear Information System (INIS)

Control of thermal expansion is often necessary in the design and selection of electronic packages. In some instances, it is desirable to have a coefficient of thermal expansion intermediate between values readily attainable with single or two phase materials. The addition of a third phase in the form of fillers, whiskers, or fibers can be used to attain intermediate expansions. To help design the thermal expansion of multiphase materials for specific applications, a closed form model has been developed that accurately predicts the effective elastic properties of isotropic filled materials and transversely isotropic lamina. Properties of filled matrix materials are used as inputs to the lamina model to obtain the composite elastic properties as a function of the volume fraction of each phase. Hybrid composites with two or more fiber types are easily handled with this model. This paper reports that results for glass, quartz, and Kevlar fibers with beta-eucryptite ...

Energy Technology Data Exchange (ETDEWEB)

A probability-based approach is presented as the integration of probabilistic methods and deterministic modelling based on the finite element method. An existing finite element software package was linked to an existing probabilistic package to analyse the complex mechanics that occur during the transient non-linear analysis of impact problems. This methodology is applied to a pipe whip analysis of a group-distribution-header, which results from a guillotine break, and subsequent impact with the adjacent building wall; this is a postulated accident for the Ignalina Nuclear Power Plant RBMK-1500 reactors. The uncertainties of material properties, component geometry data and loads were taken into consideration. The probabilities of failure of the impacted header and of the header support-wall were estimated given uncertainties in material properties, geometrical parameters and loading. The software ProFES was used for the probabilistic analysis ...

British Library Electronic Table of Contents (United Kingdom)

The antimicrobial effects and quality changes of O2, He, N2 or N2O-enriched active modified atmosphere packaging -MAP- (100 kPa initial gas partial pressure) compared to a chlorinated -100 mg L-1 NaClO- passive MAP (control) in fresh-cut Red Chard baby leaves up to 8 days at 5 degreeC were studied. High O2 MAP (>85 kPa O2) inhibited natural microflora growth during 7 days at 5 degreeC. Regarding control treatment, no differences for He and N2O-enriched MAPs on microbial growth were found although control samples were previously disinfected. Initial total phenolics content (613 mg ChAE kg-1 fw) increased up to 61-93% after 6 days at 5 degreeC under O2, He, and N2-enriched MAPs. Vitamin C content decreased up to 67% after shelf life in control samples while lower decreases were monitored in ...

Energy Technology Data Exchange (ETDEWEB)

What kind of hardware and software should be used to interface GPIB devices with the existing computer system. One idea was to use a commercially available Multibus card, BLC 8488 from National Semiconductor, whose on-board Z80 would manage the GPIB read/write functions and handshakes. With this card, one could make a hardware system which would consist of (1) CAMAC 080, (2) Multibus crate, (3) M. Shea's M68000, (4) M080, (5) BLC 8488 and (6) memory board. And the software considered for such a hardware package was GAS, which had been an established software package for communication between the ACNET computer system and smart CAMAC modules. However, a second idea was to put everything on a two-wide CAMAC module. The author pursued the second idea and came up with a two-wide CAMAC module called C488. The author describes the hardware - block diagrams, circuit blocks, front panel and hardware tests. He also refers to the software - ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes a proposed set of guidelines for analyzing the energy savings achieved by a package of retrofits or an extensive rehabilitation of an existing home. It also describes certain field test and audit methods that can help establish accurate building system performance characteristics that are needed for a meaningful simulation of whole-house energy use. Several sets of default efficiency values have been developed for older appliances that cannot be easily tested and for which published specifications are not readily available. These proposed analysis procedures are documented more comprehensively in NREL Technical Report TP-550-38238.

Science.gov (United States)

A rotational speed control, tailored to the Sunflower system requirements, was designed and fabricated in breadboard, preprototype, and prototype configurations. These units were subjected to performance and environmental testing which has led to design improvements. Program efforts have yielded hardware capable of meeting all performance requirements and of operating under all the environmental conditions to which the units were exposed. Attractive design changes were identified and, in some cases, completed. These changes involve improvements in circuitry and packaging, the primary objectives of which are to eliminate startup bias batteries and reduce weight. It is recommended that the reported program be extended to implement these improvements. (auth)

Energy Technology Data Exchange (ETDEWEB)

The paper presents the integration of the SIMBAD space charge module in the UAL framework. SIMBAD is a Particle-in-Cell (PIC) code. Its 3-D Parallel approach features an optimized load balancing scheme based on a genetic algorithm. The UAL framework enhances the SIMBAD standalone version with the interactive ROOT-based analysis environment and an open catalog of accelerator algorithms. The composite package addresses complex high intensity beam dynamics and has been developed as part of the FAIR SIS 100 project.

Energy Technology Data Exchange (ETDEWEB)

Contract No. DACA 90-8l-C-oo72 directs that a basewide energy study be accomplished for the Mannheim and Pirmasens Military Communities, Federal Republic of Germany. The project is identified as Energy Engineering Analysis Program (EEAP) Package No. 5. The overall objective of the study is to produce a systematic plan of improvement projects that will reduce by 1985 the energy consumption in compliance with the Army Facilities Energy Plan without decreasing the readiness posture of the Army.

International Nuclear Information System (INIS)

Two aspects of the chromatin repeat length (r_l) are discussed: (i) Why is r_l longer for slowly dividing cells than in rapidly dividing cells?, and (ii) Why is the temporal evolution of r_l a decreasing function of time (t) in mammalian cortical neurons whereas it is an increasing function of t for granule cells around the time of birth? These questions are discussed in terms of a hypothesis which assumes a correlation between deoxyribonucleic acid (DNA) packaging, transcription, and replication. (author). 27 refs.

British Library Electronic Table of Contents (United Kingdom)

The Rosebel gold district is hosted in a Paleoproterozoic greenstone belt of the Guiana Shield and has many characteristics that enable classification of the ores as an orogenic gold deposit. Host rocks have undergone several phases of deformation. However, gold deposition occurred late in the structural history of the belt, and is considered part of a late regional metallogenic event with respect to the geotectonic evolution of the Guiana Shield. Economic gold mineralization is hosted in felsic to mafic volcanic rocks and two sedimentary successions that are differentiated into turbiditic and arenitic depositional packages. The detailed lithostratigraphic characterization and the geochemistry enable the correlation of the local rock types with the Paramaka, the Armina, and the Rosebel for...

International Nuclear Information System (INIS)

Source-term codes to predict the release of radionuclides from nuclear waste packages have been developed and implemented worldwide. A survey and initial comparison of the attributes and capabilities of 13 international source-term codes was recently completed. This preliminary analysis focused on comparison of transport factors/processes and solution methods. This initial comparison is a necessary first step in a properly-conceived, systematic benchmarking of source-term codes. Advantages of such a comparison include assurance of the mathematical correctness of implemented models, comparison and quantification of variances introduced by different types of simplifications, and identification and quantification of the impact of near-field processes.

Energy Technology Data Exchange (ETDEWEB)

The demand for energy management in teaching packages of Higher Vocational schools in the Netherlands and the possibilities to implement energy management into the different sectors of this school type have been investigated. The results are based on interviews with representative of the above-mentioned school types. Recommendations are made for a follow-up of this investigation in order to set up an energy management teaching module. 1 tab., 1 appendix

International Nuclear Information System (INIS)

The resistance of several packaging materials to penetration by 4 species of rice insect pests was determined. Five insects of adult or larval stage were confined in pouches made from 9 different packaging materials with or without irradiated rice. It was observed that both adults and larvae of species Tribolium castaneum Herbst., Sitophilus zeamais L., Oryzaephilus surinamensis L. and Cocyra cephalonica Stainton, were incapable of penetrating pouches made from white polyvinychloride of 0.175mm thickness, low density polyethylene of 0.130mm thickness and 0.150mm thick low density polyethylene. However, penetrations marks were found in pouches made from hard paper with a thickness of 0.155mm, clear polivinylchloride of 0.130mm thickness, low density polyethylene of 0.085mm thickness, low density polyethylene 0.100mm thick, high density polyethylene of 0.06mm thickness and 0.080mm thick polypropylene. Tribolium castaneum could be considered as a ...

Energy Technology Data Exchange (ETDEWEB)

Los Alamos National Laboratory (LANL) is a unique facility covering over 43 square miles. The Emergency Management and Response Office (EM&R) is required to respond, provide Incident Command (IC), and coordination for all Laboratory emergencies. This requires IC`s and support staff to respond to the actual scene of the incident. Since the IC is under numerous constraints and stress, the office wanted the capability of locating the EM&R vehicles on an electronic map. An automated vehicle location (AVL) system was required for the additional safety of the emergency response personal. The requirements for the AVL system include total automatic tracking and low cost. After careful consideration, it was determined that the most efficient and cost effective system would be based on packet radio technology as the transmission media. The location is determined by the Department of Defense Global Positioning System (GPS). The system that was designed and constructed required four ...

International Nuclear Information System (INIS)

In order to qualify corrosion resistant materials for high level waste (HLW) packagings acting as a long-term barrier in a rock salt repository, the corrosion behaviour of the preselected materials Ti 99.8-Pd, Hastelloy C4 and two unalloyed steels was investigated. The resistance of the materials to general corrosion, local corrosion and stress corrosion cracking was examined under postulated accident conditions in the repository by long-term immersion tests of up to 4 years duration and electrochemical methods. The parameters investigated were different salt brines, temperatures of 90 deg. C, 170 deg. C and 200 deg. C as well as a gamma radiation field of 10"3Gy/h (10"5rad/h). Among the materials studied, Ti 99.8-Pd exhibited the highest corrosion resistance. This material corroded at a very low rate (

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A phosphorus-containing low alkali metal content zeolitic catalyst made from a clay starting material is provided. The catalyst is obtained by contacting a partially cation exchanged calcined zeolite-containing catalyst with an anion such as a dihydrogen phosphate anion or a dihydrogen phosphite anion and additionally with an ammonium salt other than a salt of an inorganic acid of phosphorus. A hydrocarbon catalytic cracking process utilizing the phosphorus-containing catalyst is also provided.

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Short communication.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication.

J-STORE (Japan)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The 12 months stability study of freshly produced refined soybean oil revealed that refined soybean oil stored in plastic containers in dark was more hydrolytically and oxidatively stable than that stored in other containers in light condition. There was no significant difference at P < 0.05 in free fatty acids and acid value of oil stored under light and dark conditions in tin and glass containers but there was significant difference at P < 0.05 in peroxide value of oil stored in light and dark conditions in all the storage containers. Light increased the degree of oxidative rancidity of refined soybean oil, the most in tin containers, followed by glass containers and the least in plastic containers. (author)

International Nuclear Information System (INIS)

Integrated Leakage Rate Test (ILRT) of containment system plays a very important role in safety of a Nuclear Power Plant. Containment system constitutes the last physical barrier to release of radioactivity from the core and is called upon to mitigate the consequences of not only accidents within the design basis, but also some of the highly unlikely severe accidents. Hence, leak tightness of containment becomes uttermost priority for the safety of plant personnel and public. The containment and associated ESFs are tested before the first criticality and there after periodically during service. The pre-operational integrated leakage rate is carried out at LOCA based design pressure, at periodic test pressure and at some intermediate pressure points to assess the leakage characteristics. This paper summarizes the various requirements and activities relevant to the ILRT of the Indian Pressurized Heavy ...

Energy Technology Data Exchange (ETDEWEB)

This ACDR was performed following completed of the Conceptual Design Report in July 1992; the work encompassed August 1992 to January 1994. Mission of the WRAP Module 2A facility is to receive, process, package, certify, and ship for permanent burial at the Hanford site disposal facilities the Category 1 and 3 contact handled low-level radioactive mixed wastes that are currently in retrievable storage at Hanford and are forecast to be generated over the next 30 years by Hanford, and waste to be shipped to Hanford from about DOE sites. This volume provides an introduction to the ACDR process and the scope of the task along with a project summary of the facility, treatment technologies, cost, and schedule. Major areas of departure from the CDR are highlighted. Descriptions of the facility layout and operations are included.

Energy Technology Data Exchange (ETDEWEB)

This report provides a user's manual for PROTOCOL, a comprehensive coupled kinetic/equilibrium computer program for analyzing the dissolution reactions of solids with aqueous solutions, specifically applied to the potential corrosion of vitrified nuclear waste by groundwater. The capabilities and available options are summarized as well as instructions for setting up and running problems. Also described in this report and included in the PROTOCOL software package are MASTER, a master file of species thermodynamic data, MANEQL, a preprocessor program and POSTP, a postprocessor. POSTP provides offline plotting using the CRAY-1 DISSPLA 9.0 graphics library. PROTOCOL is operational on the CDC-7600 and CRAY-1 computers at the Lawrence Livermore National Laboratory. 7 references, 10 figures, 2 tables.

International Nuclear Information System (INIS)

Radioactive waste shipping and receiving facilities presently planned for commercial and defense high-level nuclear waste will handle waste packages at frequencies far in excess of those in common practice today. If current limits for radiation levels at the cask surface and current handling methods are used, high cumulative personnel exposure to ionizing radiation is projected to occur. To reduce these exposure levels, alternate handling methods are being developed and demonstrated. The production nature of cask receiving operations, suggests commercial robotics be incorporated into a remote handling system to reduce predicted worker exposure to acceptable levels while maintaining or increasing throughput. The first phase of cask handling system development culminated in a proof-of-principle test demonstrating the feasibility of performing cask receiving and unloading operations in a remote and partially automated manner.

CERN Document Server

This book examines the applications of Monte Carlo (MC) calculations in therapeutic nuclear medicine, from basic principles to computer implementations of software packages and their applications in radiation dosimetry and treatment planning. It is written for nuclear medicine physicists and physicians as well as radiation oncologists, and can serve as a supplementary text for medical imaging, radiation dosimetry and nuclear engineering graduate courses in science, medical and engineering faculties. With chapters is written by recognised authorities in that particular field, the book covers the entire range of MC applications in therapeutic medical and health physics, from its use in imaging prior to therapy to dose distribution modelling targeted radiotherapy. The contributions discuss the fundamental concepts of radiation dosimetry, radiobiological aspects of targeted radionuclide therapy and the various components and steps required for implementing a dose ...

CERN Document Server

In the context of the LHC computing grid (LCG) project, the applications area develops and maintains that part of the physics applications software and associated infrastructure that is shared among the LHC experiments. The "physicist interface" (PI) project of the LCG application area encompasses the interfaces and tools by which physicists will directly use the software, providing implementations based on agreed standards like the analysis systems subsystem (AIDA) interfaces for data analysis. In collaboration with users from the experiments, work has started with implementing the AIDA interfaces for (binned and unbinned) histogramming, fitting and minimization as well as manipulation of tuples. These implementations have been developed by re-using existing packages either directly or by using a (thin) layer of wrappers. In addition, bindings of these interfaces to the Python interpreted language have been done using the dictionary subsystem of the LCG ...

British Library Electronic Table of Contents (United Kingdom)

Glass ceramics are commonly used as sealing materials for planar solid oxide fuel cells (SOFCs). The major requirements of stack and module builders for these materials are the stability of the coefficient of thermal expansion (CTE), excellent bonding (sticking) behaviour and the absence of volatile ingredients, which can lead to changes of the material properties and the sealing ability. SCHOTT Electronic Packaging has developed special glasses and glass-ceramics for various solid oxide fuel cell designs and operating temperatures. The glass compositions are based on the system MgO-Al2O3-BaO-SiO2-B2O3. In this study the evaluation of the developed materials was done by high temperature aging tests for up to 1000h, high temperature XRD-studies and Rietveld calculations, combined with scann...

International Nuclear Information System (INIS)

A sensitivity analysis was conducted to evaluate the technical issues pertaining to possible destructive interactions between spent nuclear fuels (SNFs) and the stainless steel canisters. When issues are identified through such an analysis, they provide the technical basis for answering what if questions and, if needed, for conducting additional analyses, testing, or other efforts to resolve them in order to base the licensing on solid technical grounds. The analysis reported herein systematically assessed the chemical and physical properties and the potential interactions of the materials that comprise typical US Department of Energy (DOE) SNFs and the stainless steel canisters in which they will be stored, transported, and placed in a geologic repository for final disposition. The primary focus in each step of the analysis was to identify any possible phenomena that could potentially compromise the structural integrity of the canisters and to assess their thermodynamic feasibility

British Library Electronic Table of Contents (United Kingdom)

The efficient design of computation intensive multidimensional signal processing applications requires dealing with three kinds of constraints: those implied by the data dependencies, the non-functional requirements (real-time, power consumption) and resources availability of the execution platform. Modeling and Analysis of Real-time and Embedded systems (MARTE) UML profile through its repetitive structure modeling (RSM) package is well suited to model the inherent parallelism within these applications, a compact representation of parallel execution platforms and the distributive mapping of one on another. The execution of such a specification respects the whole set of constraints defined upon, while the quality of the scheduling is directly linked to the quality of the mapping of the mult...

Energy Technology Data Exchange (ETDEWEB)

Actinide recycling by partitioning and transmutation is considered as one of the most promising strategies to reduce the inventory of radioactive waste, thus contributing to make nuclear energy sustainable. To make advances beyond the current state of the art in pyrochemical separations processes, the Domain 2 (DM2) of ACSEPT has been built on considering a process approach based on system studied. Four work packages that represent the main steps of a process block diagram have been identified: head-end steps, core process development, and salt treatment for recycling and waste conditioning. The results obtained in this domain will be integrated in DM 3 (Process) in order to orientate the R and D studies of DM2 and to propose and validate flowsheets at the end of the project. The state of the art on pyrochemical separation within the European Community and the working program of ACSEPT in pyrometallurgy are presented in this work. (authors)

Energy Technology Data Exchange (ETDEWEB)

The decommissioning of the Sodium Reactor Experiment is essentially complete. Contaminated materials, equipment, and soil were removed, decreasing the residual radioactivity to levels acceptable for future unrestricted use of the site. The fuel was removed and declad, tooling and techniques to support the decommissioning were developed, bulk sodium and residual sodium films were removed, coolant systems were dismantled, the reactor vessel was dissected, the interior surfaces of the facilities were decontaminated, and waste materials were packaged and shipped to burial sites. Radiation exposure to workers and the public was within the guidelines and as low as reasonably achievable. In performing the project, new decontamination techniques were tested, decontamination equipment was evaluated, and waste disposal methods were developed.

Energy Technology Data Exchange (ETDEWEB)

Basic information on photovoltaic conversion technology is provided for those unfamiliar with the field. Various types of photovoltaic products and systems currently available off-the-shelf are described. These include products without batteries, battery chargers, power packages, home electric systems, and partial systems. Procedures are given for designing a photovoltaic system from scratch. A few custom photovoltaic systems are described, and a list is compiled of photovoltaic firms which can provide custom systems. Guidance is offered for deciding whether or not to use photovoltaic products. A variety of installations are described and their performance is appraised by the owners. Information is given on various financial incentives available from state and federal governments. Sources of additional information on photovoltaics are listed. A matrix is provided indicating the sources of various types of photovoltaic products. The addresses of suppliers are ...

International Nuclear Information System (INIS)

The electronic structure and optical properties in tetragonal ceramics PbTiO_3, are studied by using full-potential linearized augmented plane wave method in density functional theory with the generalized gradient approximation by WIEN2K package. The theoretical calculated optical properties and energy loss spectrum yield a static refractive index of 2.59 and a plasmon energy of 22.7eV for the tetragonal phase. The effective electron number at low energy saturates near 22-23eV with the value of 50 for the effective electron number. The results show a indirect band gap of 2.2eV at the I' point in the Brillouin zone. The :calculated band structure and density of states of PbTiO_3 agree with previous experimental and theoretical results.

Energy Technology Data Exchange (ETDEWEB)

The fundamental points to be considered in a waste treatment system for a country like Japan, where the final disposal method has not been decided and the wastes have to be stored in the power plants, are volume reduction of the wastes, safe storage of the wastes in the plant, and flexibility regarding the final disposal. A system has been developed that consists of a thin film evaporator for the direct solidification of the liquid waste, a pelletizer for producing hard pellets from the powdered wastes, a pellet storage unit, and a solidification unit for the final disposal. A pilot plant with waste treatment capacity of 200 kg/h was built in 1976 and has proved the system feasibility. This paper reports on pilot plant tests of the thin film evaporator and other components, tests on pellet deterioration during long term storage, and integrity tests on the final disposal of the pellet bitumen package.

International Nuclear Information System (INIS)

The final product of the radwaste conditioning process must satisfy certain requirments and physico-chemical properties in order to assure its safe long-term behaviour. Of course, the foreseen quality assurance and quality control should be conducted by means of non-destructive techniques. This work presents an over-view of various applicable non-destructive methods of analysis, showing their fields of investigation in testing waste packages, together with some arising practical problems. The most promising methods, such as eddy current testing, ultrasonic testing, #gamma#-scanning, #gamma#-spectroscopy, neutron counting and computerized tomography, are treated more deeply and some applications are presented. Particular attention is devoted to the development of a device based on computerized tomography; its essential components are reported and some design problems are also discussed.

Energy Technology Data Exchange (ETDEWEB)

Since August 1984, the MITRE Corporation has been supporting the Naval Sea Systems Command (NAVSEA) and the Naval Medical Command (NAVMEDCOM) in their joint efforts to enhance the Navy Occupational Health Information Management System (NOHIMS). The goal of the enhancement effort was to create a comprehensive occupational health and safety system for Navy industrial facilities by expanding upon the original NOHIMS functions and adding modules for hazard deficiency abatement, hazardous-material control, injury claims and compensation, and safety and health training. To meet this goal, MITRE developed an enhanced industrial subsystem, referred to as the Occupational Safety and Health Record Keeping System (OSHRKS), using a prototyping approach and a public-domain data base-management software package, the Veterans Administration's (VA's) FileManager (FileMan).

International Nuclear Information System (INIS)

The losses of Hg from phenol formaldehyde resin - bound standards and hair samples in neutron activation analysis in case of their irradiation in the water filled nuclear reactor channel is studied. The mean losses of Hg during 20-30 hrs irradiation at (2-3)x10"1"8 n/cm"2 are 15-20% with their stopping at double Al-covers. The mean losses of Hg from standards at 200, 250 and 300 deg C are 30, 61 and 86% respectively and do not occur at 150 deg C after their 5 hour heating. The losses of Hg from hair samples packed in polyethylene tubes through the package walls in experimental conditions are not observed.

Energy Technology Data Exchange (ETDEWEB)

The present conference on lens design encompasses physical and geometrical optics, diffractive optics, the optimization of optical design, software packages, ray tracing, the use of artificial intelligence, the achromatization of materials, zoom optics, microoptics and GRIN lenses, and IR lens design. Specific issues addressed include diffraction-performance calculations in lens design, the optimization of the optical transfer function, a rank-down method for automatic lens design, applications of quadric surfaces, the correction of aberrations by using HOEs in UV and visible imaging systems, and an all-refractive telescope for intersatellite communications. Also addressed are automation techniques for optics manufacturing, all-reflective phased-array imaging telescopes, the thermal aberration analysis of a Nd:YAG laser, the analysis of illumination systems, athermalized FLIR optics, and the design of array systems using shared symmetry.

Energy Technology Data Exchange (ETDEWEB)

This research aims to develop reliable, advanced system thermal-hydraulic computer code and to quantify the uncertainties of code to introduce the best estimate methodology of ECCS for LBLOCA. Although the one of best estimate code, RELAP5/MOD3.1 was introduced from USNRC, several deficiencies in its reflood model and some improvements have been made. The improvements consist of modification of reflood wall heat transfer package and adjusting the drop size in dispersed flow regime. The tome smoothing of wall vaporization and level tracking model are also added to eliminate the pressure spike and level oscillation. For the verification of improved model and quantification of associated uncertainty, the FLECHT-SEASET data were used and upper limit of uncertainty at 95% confidence level is evaluated. (Author) 30 refs., 49 figs., 2 tabs.

British Library Electronic Table of Contents (United Kingdom)

During the past few decades, the basic assumption of agroclimatic zoning, i.e., that agroclimatic conditions remain relatively stable, has been shattered by ongoing climate change. The first aim of this study was to develop a tool that would allow for effective analysis of various agroclimatic indicators and their dynamics under climate change conditions for a particular region. The results of this effort were summarized in the AgriClim software package, which provides users with a wide range of parameters essential for the evaluation of climate-related stress factors in agricultural crop production. The software was then tested over an area of 114,000?km2 in Central Europe. We have found that by 2020, the combination of increased air temperature and changes in the amount and distribution ...

Energy Technology Data Exchange (ETDEWEB)

Epitaxial films grown pseudomorphically on substrates provide a way to stabilise non-equilibrium structures of materials. Obviously, there always is a certain lattice misfit between substrate and film material in its bulk equilibrium structure. In the pseudomorphic regime, this misfit can either lead to the growth of films in a strained bulk structure or even yield structures that are not stable in the bulk. Large misfits do not necessarily imply large lateral stress. Theory can help to predict e.g. geometry, stress and magnetic properties of pseusomorphically grown metal films. In this work, we considered the fcc-bcc epitaxial Bain path of 3d, 4d, and 5d transition metals, which provides a reasonable description of tetragonally distorted films on substrates. We carried out density functional calculations in the implementation of the full potential local orbital program package FPLO. Emphasis is put on similarities among the transition metals.

Energy Technology Data Exchange (ETDEWEB)

Ba, Cd, Cr, Cu, Fe, Ni, Pb and Zn were determined in birch leaves (Folium Betulae), dandelion roots (Radix Taraxacae), hawthorn blossom (Inflorescentia Crataegi) and their infusions by graphite furnace atomic absorption spectrometry (GFAAS) after microwave digestion of plant samples. Infusions were made from herbs according to prescription for patients, provided by the producer of medicine on the package. The results obtained were compared with daily requirements for each element. Results show high content of cadmium in the medicinal plants analyzed. The highest level in infusions was observed for Ni and Zn (over 90% of the total element concentration for Ni and in most cases over 50% for Zn), and the lowest for Cd and Pb. The calculated daily intake of majority of the analyzed elements was very low (under 1% of daily requirements)

British Library Electronic Table of Contents (United Kingdom)

Ultrasonic gold and aluminum wire wedge bonding are widely used for electrical and signal interconnections of the integrated circuit chip packages. In this paper, based on the metallurgical theories and thermal aging test methods, the long-term thermal reliabilities of gold and aluminum wire wedge bonding on aluminum and Au/Ni/Cu pads, were investigated, respectively. At 200degreeC, the Au/Al bond interfaces evolved little when the storage time was less than 48h; with the aging time increasing, the interfacial intermetallic compounds (IMC) grew up from the pad (vertical growth); the primary compounds were Au5Al2 near the bond toe and heel, and Au2Al at the periphery. Then, the thickness of IMC was unchanged, and extended horizontally (lateral growth), Au5Al2 transformed into more stable Au...

Energy Technology Data Exchange (ETDEWEB)

The Jeanne d`Arc Basin is located 320 km offshore in the Grand Banks of Newfoundland. It is a Mesozoic failed-rift basin with recoverable oil reserves of about 2 billion barrels. Its huge Hibernia Field will be in production by late 1997. The basin has been reappraised using sequence stratigraphic concepts, and renewed exploration in the area is expected. The Upper Jurassic - Lower Cretaceous sedimentary accumulation in the Basin was formed by the extensional tectonics that created the North Atlantic Ocean. The sedimentary packages were placed in chronostratigraphic order by calibrating the biostratigraphy of the Oxfordian to Maastrichtian section to the detailed ammonite zonation from the North Sea.

Energy Technology Data Exchange (ETDEWEB)

In the absence of empirical outdoor thermal comfort studies it has been widely assumed that indoor thermal comfort theory generalises to outdoor settings without modification. Many indoor models were developed to describe thermal discomfort, not stress, therefore their relevance to conditions that vary greatly from neutrality, as many outdoor climatic conditions do, has not been critically validated in the field to date. The thermal comfort of 1018 subjects in outdoor and semi-outdoor locations in subtropical Sydney was investigated by a questionnaire and a comprehensive package of micro-meteorological instruments. The thermal neutrality in terms of the thermal comfort index OUT{sub S}ET* of 26.2 {sup o}C was significantly higher than the indoor SET* counterpart of 24{sup o}C (ASHRAE Trans. 92 (1986) 709). (author)