Science.gov (United States)

Not Available

Science.gov (United States)

... Descriptors : *POLYMERS, *BINDERS, *HOWITZERS, *COMBUSTIBLE CARTRIDGE CASES, CHEMICAL COMPOSITION, PROPELLING ...

International Nuclear Information System (INIS)

The radiation polymerization of multifunctional unsaturated polyester-monomer mixtures in wood forms interpenetrating network system. The mechanical resistance (compression, abrasion, hardness, etc.) of these composite materials are generally well over the original wood, however the impact strength is almost the same or even reduced, in comparison to the wood itself. An attempt is made using elastic polyester resins to produced wood-polyester composite materials with improved modulus of elasticity and impact properties. For the impregnation of European beech wood two types of elastic unsaturated polyester resins were used. The exothermic effect of radiation copolymerization of these resins in wood has been measured and the dose rate effects as well as hardening dose was determined. Felxural strength and impact properties were examined. Elastic unsaturated polyester ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work is to investigate the effects of matrix resin and fiber content on the behavior of fatigue crack propagation in continuous-glass-fiber-mat reinforced CP-resin composites. For this purpose, ductile matrix resin and brittle one are used. These two kinds of resins have the characteristic that the elastic modulus and tensile strength are nearly the same with each other while the elongation is different. The composite specimens are made of these resins and continuous grass fiber mat of 20 wt.% and 60 wt% fiber contents. The fatigue crack propagation test was conducted by using the tapered DCB specimens to control the stress intensity factor range, {delta}K, during the test. The results obtained are as follows; (1) The relation between the crack propagation rate, da/dN, and {delta}K for all the present materials is ...

International Nuclear Information System (INIS)

Phenolic resins have made a major breakthrough in the field of high technology in 80's. These are now active participants of "high tech' areas ranging from electronics, computers, communication, outer space, aerospace, advanced materials, bio materials and technology. A phenol - formaldehyde (1:1.5) resin having resin content of 70% synthesized in the laboratory has been applied for wood coating and reinforcing glass fiber. The weatherability and solvent resistance of these items have been studied and results discussed keeping in view the envisaged application for structural materials and chemical equipment. The toxic materials released during contact with solvents for chemical applications and during degradation general have been monitored. The results are discussed with reference to environmental pollution due to these resins and their composites under different conditions. ...

Energy Technology Data Exchange (ETDEWEB)

This invention relates to the production method of composite electrode substrate for fuel cell. An impermeable material is used for edge sealant. The sealant is put in the clearance between two electrodes consisting of porous carbon material via thermoplastic resin sheet, and heated while being pressed. This production method increases the adherence between the porous carbon bodies and reduces the contact resistivity at the joint interface. Consequently, it becomes possible to produce the composite electrode for fuel cell without separator, resulting in simplification of assembly work, weight reduction, and downsizing. The preferable porous carbon body is made from shrinkage-treated fiber. After sheet forming, the thermosetting resin is impregnated, and then it is burnt to carbonization. Or mixed sheet of rayon and acrylic fiber is laminated to be heated and pressed without impregnating the ...

International Nuclear Information System (INIS)

Low molecular weight epoxy resin based on diglycidyl ether of bisphenol A was synthesized and mixed at constant percentages with natural rubber. The rubber epoxy system was cured with various types of curing agents such as ethylene diamine, maleic anhydride as well as the prepared resole phenol formaldehyde. A study of the photo-induced crosslinking of the prepared elastic adhesives and film samples was carried out by exposure to ultraviolet lamp (300 w) for 2 weeks at 20 deg. C. Samples containing ethylene diamine were cured at 25 + - 1 deg. C. for 24 h while samples containing maleic anhydride or resole phenol formaldehyde resins were thermally cured at 150-170 deg. C. for 10 min. Cured adhesive compositions were tested mechanically and physically and evaluated as wood adhesives. While hardness, chemical resistance as well as heat stability of the prepared cured film sample were investigated. The obtained data indicate ...

Energy Technology Data Exchange (ETDEWEB)

Formulas were developed based on an aqueous solution of hydrolyzed polyacrylonitrile widely used in the oil industry. The additive used consisted of products of industrial production: synthetic resin TEG-1 with hardening agent PEPA (polyehtylene polyamine) and technical formalin. The mixtures containing about 80-85% by volume 5% hydrolyzed polyacrylonitrile, 10-15% by volume of resin TEG-1 with hardening agent PEPA and 3-5% by volume formalin satisfy the requirements made for the plugging materials. The initial mixtures are distinguished by technological efficiency of preparation and have controllable hardening periods. Physical-chemical properties are given for the gel polymers. In the set of properties, the mixtures based on hydrolyzed polyacrylonitrile, resin TEG-1 with hardening agent PEPA and formalin can be recommended as plugging materials of temporary action with complex treatment of the heterogeneous beds.

International Nuclear Information System (INIS)

Some aspects of metrological provision of X-ray radiometric analyzers for mineral raw composition and gamma-gamma-logging equipment are considered. Standard samples (SS) based on the phenol-formaldehyde resin with the introduced quantities calculated of element compositions in the form of oxides and salts are described. Principles of metrological provision developed are used when carrying out state acceptance tests of X-ray radiometric analyzer RAL-M-102 ''Ehkran'' and gamma-gamma-logging equipmnt RSK-102. Economic benefit from introduction of an SS set is #approx# 60-100 thousand roubles per year.

International Nuclear Information System (INIS)

A laminated material composed of glass cloth/polyimide film/epoxy resin will be used as an insulating material for superconducting coil of International Thermonuclear Experimental Reactor (ITER). In order to keep safe and stable operation of the superconducting coil system, it is indispensable to evaluate radiation resistance of the material, because the material is exposed to severe environments such as high radiation field and low temperature of 4 K. Especially, it is important to estimate the amount of gases evolved from the insulating material by irradiation, because the gases affect on the purifying system of liquid helium in the superconducting coil system. In this work, the gas evolution from the laminated material by gamma ray irradiation at liquid nitrogen temperature (77 K) was investigated, and the difference of gas evolution behavior due to difference of composition in the epoxy resin was discussed. It was found ...

Energy Technology Data Exchange (ETDEWEB)

Wood-Polymer Composites (WPC) was prepared from recycled films of agricultural use and wood wastes, and LLDPE and neat PE resin mixture were also utilized in order to compare the properties. Maleic anhydride (MA) and dicumyl peroxide were used as an adhesion promoter and an initiator, respectively. Tensile properties of WPC were measured via tensile test as a function of wood filler and MA content, and fracture surface was also investigated with SEM. As the content of wood filler increased, elongation decreased but modulus increased. However, tensile strength of WPC increased only when MA was used, and 1 wt.% of MA may be high enough to increase the tensile properties. The tensile properties of WPC prepared from recycled PE films were almost same as those of neat PE resin mixture. (author). 18 refs., 5 figs.

Science.gov (United States)

The purpose of this study was to evaluate the resin-dentin interfacial morphology and shear bond strength of several new and experimental dentin bonding systems classified as single-bottle/total etch, multi-step/total etch, and self-etching. Class 1 and 5 cavities were prepared from freshly extracted permanent molars and restored with composite resin. Each bonded sample was cross sectioned and one-half was completely demineralized and deproteinized, while the other half was polished along the cut surface to permit measurement of the thickness of resin-infiltrated dentin layer (RIDL) within intertubular dentin (iRIDL) and around the peritubular walls (pRIDL) of resin tags by SEM. Shear bond strength was measured for all the systems 2 minutes after photocuring. SEM showed iRIDL and resin tags of different morphology depending on material and dentin location. The ...

Energy Technology Data Exchange (ETDEWEB)

Composites based on pure gypsum and polyester-styrene resin have been prepared using various doses of gamma radiation. Some physical properties of the prepared composites and the influence of irradiation dose on it have been studied as: compression strength, hardness, thermal decomposition temperature in nitrogen or oxygen, and the change in weight in aqueous solutions with different pH values. The glass transition temperature of the pure polymer and the composites increases with increasing the irradiation dose up to a plateau, and the glass transition temperature of the pure polymer is lower than that of the composites. The irradiation dose does not seem to affect the decomposition temperature of the pure polymer or the composites significantly and the decomposition temperature in presence of nitrogen is higher than that in presence of oxygen. Increasing the ...

British Library Electronic Table of Contents (United Kingdom)

The results of the thermal dissolution of Barzas sapromyxite coal in benzene under supercritical conditions in a flow system are reported. It was found that the mechanical pretreatment of coal under intense impact bending conditions resulted in an increase in the yield and a change in the group composition of the liquid products: in the high-temperature region of the process, the concentration of high-molecular-weight components (preasphaltenes, asphaltenes, and resins) increased.

Energy Technology Data Exchange (ETDEWEB)

A process is disclosed for the preparation of liquid, storage-stable, polyisocyanate compositions containing a release agent formed in situ which compositions are useful, for example, as binder resins in the formation of particle boards which latter, because of the presence of the release agent, show no tendency to adhere to the face of metal platens used in their formation. The process comprises heating an organic polyisocyanate (polymethylene polyphenyl polyisocyanate preferred) with an acid phosphate (e.g. a mixture of mono-and di-alkyl acid phosphates) under conditions controlled as to time and temperature so as to yield a product which is storage stable and shows no tendency to deposit solid or to separate into two liquid phases.

British Library Electronic Table of Contents (United Kingdom)

We prepared macromer-grafted polymers (MGPs) containing suitable polymer side chains for improving solubility and pyrene units for improving adsorption on multiwalled carbon nanotube (MWCNT) surfaces, and demonstrated that these MGPs act as MWCNT solubilizers that improve solubility of MWCNTs in typically poor solvents such as alkanes and that improve flowability of polymer/MWCNT composites. The polydimethylsiloxane (PDMS)-MGPs, synthesized using PDMS macromers and pyrene-containing monomers, improved solubility of MWCNTs not only in chloroform but also in hexane, which is a poor solvent for MWCNTs. Moreover, the addition of PDMS-MGP-adsorbed MWCNTs (MWCNT/PDMS-MGPs) to epoxy resin monomers or polybutylene terephthalate (PBT) drastically reduced the viscosity of the obtained epoxy resin mo...

British Library Electronic Table of Contents (United Kingdom)

A viscoelastically prestressed polymeric matrix composite (VPPMC) is produced by applying tension to polymeric fibres, the tensile load being released prior to moulding the fibres into a matrix. Following matrix solidification, compressive stresses imparted by the viscoelastically strained fibres improve composite tensile, flexural and impact properties. This study focuses on the potential for useful life and impact protection capability by performing Charpy impact tests on nylon 6,6 fibre-polyester resin samples subjected to accelerated ageing. Prior to testing, time-temperature superposition principles were used, the samples being aged by heating to 60degreeC for periods representing a 10-fold increase over previous work. The results demonstrated no deterioration in impact performance ov...

International Nuclear Information System (INIS)

The improving uranium extraction efficiency of yellow cake production from shale deposit by acid pugging and curing with D263B resin adsorption is described in this paper. The analysis and examination show that the composition of uranium minerals in one of uranium ores is very complex, which directly influence the extraction efficiency of uranium and processing technology. Conventional experimental results indicate that uranium leaching efficiency is changed between 50?60% by conventional agitation method. In this case, acid pugging and curing experiments are employed in order to improving the extraction efficiency. A series of acid pugging and curing experiments are carried out to get parameters for heap leaching in pilot plant experiment. The experiment results by acid pugging and curing technology showed that uranium leaching efficiency can reach to 90% of extraction efficiency mixed with 1% manganese dioxide, 12% sulfuric acid pugging, ...

Energy Technology Data Exchange (ETDEWEB)

An apparatus was designed and built for the purpose of exposing samples of solid polymers to varying temperatures, atmospheres and stress levels while quantitatively recording the resulting chemiluminescence. Preliminary data were acquired with this apparatus that show a correlation between an enhanced chemiluminescence signal at a low level of applied stress and a decrease in tensile strength for the most commonly used epoxy resin in high performance fiber composites, TGMDA DDS. The studies with cellular silicone cushions (which are used to accommodate thermal expansion and contraction) have defined the temperature regimes in which accelerated aging tests are valid for extrapolation to ambient temperature. Preliminary data on Kevlar fibers is also discussed.

Science.gov (United States)

... Accession Number : ADD001040. Title : Process for Uniformly Depositing Resin in Combustible Cartridge Cases. Descriptive Note : Patent,. ...

International Nuclear Information System (INIS)

Nanocomposites comprising nanocrystal silicon (Si), disordered carbon (DC), and multi-walled carbon nanotubes (MWCNTs) - denoted as Si/DC/MWCNTs - have been prepared by pyrolyzing the phenol-formaldehyde resin (PFR) mixed with Si and MWCNTs. This nanocomposite anode material showed a discharge capacity of 1216 mAh/g in the first cycle, and a charge capacity of 711 mAh/g after 20 charge-discharge, much higher than that of Si/DC composite. It can be observed that Si particles wrapped in MWCNTs were homogeneously embedded into the matrix of the DC. The improved electrochemical performance is hypothesized to be mainly attributed to the morphology stability of the composite due to the excellent resiliency and distinct electric conductivity of the MWCNTs.

International Nuclear Information System (INIS)

Ceramic matrix composites in the TiC-Ti, Y-TZP system can be synthesized by the reaction between carbon and the TiO_2-Y_2O_3-ZrO_2 solid solution nanopowder. This method results in the more homogeneous powders than those prepared by the physical mixing of TiC and zirconia s.s. powders. Twelve TiO_2-Y_2O_3-ZrO_2 solid solution nanopowders differing in the proportions of the constituent oxides were prepared by the coprecipitation- calcination route. They were reacted with the pyrolytic carbon evenly distributed within the system. Carbon was introduced by the thermal decomposition of the phenol-formaldehyde resin dissolved in ethyl alcohol and mixed with the zirconia s.s. nanopowder. Reaction was performed in vacuum. Compacts of the composite powders sintered in vacuum give dense materials of evenly distributed TiC inclusions of sizes not surpassing 400 nm. Hardness of such materials was dependent on their chemical and phase ...

Energy Technology Data Exchange (ETDEWEB)

Polycarbonate (PC), a non-crystalline resin, and polybutylene terephthalate (PBT), a crystalline resin, can be achieved by means of alloying of improving such various properties as chemical resistance, heat and impact resistance, and formability. This paper describes its manufacturing methods, properties, and market trends. A PC/PBT alloy improves the chemical resistance if the PBT composition ratio is high, but reduces thermal deformation temperature and impact strength. It is regarded adequate, therefore, that the PBT component ratio is set to 20% to 30%. The impact strength is improved by adding elastomer as a third component. The national production amount in 1992 was 4,800 tons a year; price per kilogram is 700 to 800 yen; and the main application is interior and exterior parts for automobiles. While PP and urethane are often used for interior and exterior automotive parts, there is a high possibility of transferring ...

International Nuclear Information System (INIS)

The manufacture and use of wood/plastic composite (WPC) as an example of wood matrix and wood sawdust/plastic composites (SDP) as an example of plastic matrix are reviewed. The raw material for WPC are mostly vinyl monomers, particularly methyl methacrylate and styrene. The reaction in WPC polymerization is radical polymerization. Researches on the radiation sources mostly resulted in gamma-ray. Electron beam can be applied only to thin products. The future use of WPC may be for furnitures, sporting goods, decorative parts and the like. Vital study on the reduction of manufacturing costs is required, for example, the improvement of reaction and the adoption of continuous process must be considered. The raw materials for SDP are wood sawdust, vinyl monomer (mostly methyl methacrylate) and resins. Electron beam accelerators are the most preferable radiation source because of its high efficiency and safe operation. SDP shows ...

Energy Technology Data Exchange (ETDEWEB)

Reduction of occupational radiation exposure dose in a BWR plant is achieved by an elimination of crud in a BWR primary loop condensate stream by condensate demineralizer. Crud removal by condensate polisher improves year by year, a phenomenon called the Aging Effect of Ion Exchange Resins. The cause of this phenomenon is assumed to be mainly due to changes in the cation resin property becoming more crud adsorptive, where a typical change in physical property of aged cation resin is an increase in water retention capacity. Assuming that the crud removal efficiency was influenced by a crosslinkage of cation resin, an attempt was made to enhance this removal efficiency by decreasing the crosslinkage and satisfactory results were obtained. As a result, new gel type cation resins were developed with lower crosslinkage and larger surface areas, as compared with conventional gel type ...

Science.gov (United States)

The beater additive process for manufacturing combustible cartridge cases is superior to the solvent resin, post-impregnation process. However, the current beater additive resins do not produce as good a product as the solvent-resin system. The objective ...

British Library Electronic Table of Contents (United Kingdom)

Introduction The objective of this study was to investigate the in-vitro fluoride release from a glass ionomer orthodontic bonding system (Fuji I, GC Corporation, Tokyo, Japan) over a 2-month period and the in-vivo enamel fluoride uptake after 6 months. Methods Ten metal brackets were bonded with either glass ionomer or composite resin (Transbond XT, 3M Unitek, Monrovia, Calif; Light Cure), which served as controls, to recently extracted molars. The bonded teeth, cut at the level of their roots, were stored in distilled water that was renewed after every fluoride measurement at 1, 3, 7, 30, and 60 days. The in-vitro fluoride release was measured by using a fluoride ion-selective electrode, connected to an ion analyzer. Fifteen pairs of premolars were bonded with metal brackets with either ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the work described in this dissertation is to increase the understanding of injection-pultrusion process. Three major substudies related to injection-pultrusion have been completed: measurement of the compressibility of fiber reinforcements, measurement of in-plane and transverse resin flow through fiber reinforcements, and development of a resin flow model. This dissertation also presents results of an experimental and analytical investigation of in-plane and transverse resin flow through fiber reinforcements.

Energy Technology Data Exchange (ETDEWEB)

The Dowex 50W-X8 and 50W-Xl2 resin samples are both strong acid cation materials in the hydrogen form. Each material has a water retention capacity characteristic of its respective marketed degree of cross-linking. Dowex 21K gives confirmatory responses to tests for a strong anion exchange resin in the nitrate form. All three resins have the manufacturer`s specified ionic type and form, and the Dowex 50W resins have characteristic water retention capacities. These tests conclude that the ion exchange resins in use in FB-Line meet the approved safety document criteria for cross-linking, ionic form, and resin type.

Energy Technology Data Exchange (ETDEWEB)

The development of crud removal technology has started with the finding of the resin aging effect that an old ion exchange resin, aged by long year of use in the condensate demineralizer, had an enhanced crud removal capability. It was confirmed that some physical properties such as specific surface area and water retention capacity were increased due to degradation caused by long year of contact with active oxygens in the condensate water. So, it was speculated that those degradation in the resin matrix enhanced the adsorption of crud particulate onto the resin surface, hence the crud removal capability. Based on this, crud removal resin with greater surface area was first developed. This resin has shown an excellent crud removal efficiency in an actual power plant, and the crud iron concentration in the condensate effluent was drastically reduced by this ...

International Nuclear Information System (INIS)

The 177 underground storage tanks at the DOE's Hanford Site contain an estimated 180 million tons of high-level radioactive wastes. It is desirable to remove and concentrate the highly radioactive fraction of the tank wastes for vitrification. Resorcinol-formaldehyde (R-F) resin, an organic ion-exchange resin with high selectivity and capacity for the cesium ion, which is a candidate ion-exchange material for use in remediation of tank wastes. The report includes information on the structure/function analysis of R-F resin and the synthetic factors that affect performance of the resin. CS-100, a commercially available phenol-formaldehyde (P-F) resin, and currently the baseline ion-exchanger for removal of cesium ion at Hanford, is compared with the R-F resin. The primary structural unit of the R-F resin was determined to consist of a ...

International Nuclear Information System (INIS)

The optical properties of divalent europium activated Ca-#alpha#-SiAlON were investigated and the excitation and emission processes were discussed. The emission wavelength is influenced by the activator concentration of Eu more than the codopant concentration of Ca, in case of the same matrix composition of #alpha#-SiAlON. The red-shift of emission increases when the concentration of Eu increases. In addition, it was revealed that the red-shift of emission would be caused by the construction of the package of optical device. The correlated color temperature becomes low by the red-shift for the white light-emitting diode (LED) lamp using Ca-#alpha#-SiAlON:Eu phosphor when the phosphor powder concentration increases in the transparent resin which coats the primary light source of a blue LED die. The additional red-shift can be observed when the excessive amount of phosphor coating is intentionally poured to the white LED lamps. These red-shifts ...

Energy Technology Data Exchange (ETDEWEB)

Considerations were given on typical applications of nylon resin parts to automotive use and their future trends through news topics. GF strengthened nylon resin is used in cylinder head covers substituting aluminum because of advantages in nylon resin of weight reducibility, vibration suppressibility, and noise shielding capability. Radiator tank uses N66GF 30% strengthened nylon in more than 60% of bonnet type passenger cars. Nylon resin is used most in harness connectors installed in locations that require heat resistance. External car parts such as bumpers, fenders, and wheel caps use to some extent nylon resin in the form of strengthened and up-graded polymer alloy. BMW in Germany used in its high-class production cars intake manifolds made of GF strengthened Nylon 66. The majority of engine{prime}s gas intake system parts has been replaced with Nylon blow-formed parts. The ...

International Nuclear Information System (INIS)

Russian 1977. USSR Dubinskaya, NA Kolomijtsev, MA Dundua, V.Yu.

International Nuclear Information System (INIS)

(1974). Hungary Kolomit'sev, MA Ambardanashvili, TS Dundua, V.Yu. AN

International Nuclear Information System (INIS)

A number of ion exchange materials are being evaluated as part of the Tank Waste Remediation System (TWRS) Pacific Northwest Laboratory (PNL) Pretreatment Project for the removal of "1"3"7Cs from aqueous tank wastes. Two of these materials are organic resins; a phenol-formaldehyde resin (Duolite CS-100) produced by Rohm and Haas Co. (Philadelphia, Pennsylvania) and a resorcinol-formaldehyde (RF) resin produced by Boulder Scientific Co. (Mead, Colorado). One of the key parameters in the assessment of the organic based ion exchange materials is its useful lifetime in the radioactive and chemical environment that will be encountered during waste processing. The focus of the work presented in this report is the radiation stability of the CS-100 and the RF resins. The scope of the testing included one test with a sample of the CS-100 resin and testing of two batches of the RF ...

Energy Technology Data Exchange (ETDEWEB)

In this report, the quantitative relation between the height equivalent to a theoretical plate (HETP) and the size of ion exchange resin is studied by enriching lithium isotopes with high pressure ion exchange displacement chromatography. The dependence of HETP on the size of the resin can be expressed as H = C x (anti r)sup( ) in which = 2.4 and it is found that Snyder's equation is suitable for such a system of isotope separation as may be explained by the simple displacement mechanism.

International Nuclear Information System (INIS)

Benthic invertebrates can uptake metals through diffusion of free ion solutes, or ingestion of sediment-bound forms. This study investigated the efficacy of the metal chelating resin SIR 300TM in adsorbing porewater metals and isolating pathways of metal exposure. A field experiment (Botany Bay, Sydney, Australia) and a laboratory toxicity test each manipulated the availability of porewater metals within contaminated and uncontaminated sediments. It was predicted that within contaminated sediments, the resin would adsorb porewater metals and reduce toxicity to invertebrates, but in uncontaminated sediments, the resin would not significantly affect these variables. Whereas in the laboratory, the resin produced the predicted results, in the field the resin increased porewater metal concentrations of contaminated sediments for at least 34 days and decreased abundances of four ...

Energy Technology Data Exchange (ETDEWEB)

The treatment and disposal of oily waters from oil production and refining processes represent an important technological pass for attendance of the ambient legislation and to the politics of the Cia of search of the environmental excellence. The reuse or reinjection of the co-produced water has been considered an interesting strategical alternative, however, the water quality requirement for these processes demands a pretreatment step, considering the exit effluent from primary and secondary treatment processes currently used. This work presents resulted of the polymeric resin development for tertiary treatment of oily waters with low oil and grasses content and fine solids, including the dissolved fraction. These resins can adsorb, in reversible form, organic components. Its high adsorption capacity is determined by the polarity, superficial area, range of porosity and a wide distribution of particle size and pore. Another important ...

Energy Technology Data Exchange (ETDEWEB)

The effects of the rate of resin addition and moisture content (MC) on the static bending properties and creep behavior of phenol-resin-treated particleboards are investigated. The modulus of rupture (MOR) of phenol-resin-treated boards shows the maximum value at 7 to 9 percent MC and large decreases at 19 to 28 percent MC, retaining values about 30 to 40 percent lower than those in the oven dry condition. The bending property is improved with the increase of low molecular weight resin content, and the tendency is obvious when MC is high. Creep compliance tends to increase with the increase of MC, and the rate of increase is larger with smaller resin content. The value of creep compliance after 48 hours under load becomes about 1.8 times the value in the dry condition at 7 to 9 percent MC, and about 2 times the value when MC increases to 19 to 27 percent from 7 to 9 percent. In ...

Energy Technology Data Exchange (ETDEWEB)

The paper describes uptake of gaseous lodine-131 on silver impregnated organic resin, Amberlite IR-120, available at the Secondary Steam Generator (S.S.G.) Opening at T.A.P.S. in comparison with activated charcoal. The experiments are conducted in dry and wet conditions by soaking the impregnated resin and activated charcoal in distilled water for wet condition. The paper also describes the iodine sampler specially designed and fabricated for these experiments.

International Nuclear Information System (INIS)

The report is divided into three sections. The first section contains a general introduction to ion exchange resins used in various processes, the second section describes characteristic properties of the polymer materials and the inter relation between them. This will, in turn, be useful to interpret the data obtained from the various tests carried out on the resins in the laboratory. In the third section of the report, are given the details of each method used for a particular test to be carried out on a routine basis. Each method describes the principle involved, the reagents and apparatus used in the experiment, the actual procedure and calculations and recording of the data. 3 refs. (author).

UK PubMed Central (United Kingdom)

Total anthocyanins in different cultivars of mulberry were measured and a process for the industrial preparation of mulberry anthocyanins as a natural food colorant was studied. In 31 cultivars of mulberry,...Full Text Available

Science.gov (United States)

... Abstract : The structural features of 25mm combustible cartridge cases, manufactured for this program and having nitrocellulose/resin/fiber ratios of ...

Energy Technology Data Exchange (ETDEWEB)

For the purpose of solving the limitations such as shape and dimension for magnetic compact fabricated by conventional anisotropic forming under magnetic orienting field, the feasibility of a new magnetic forming process was studied. Ferrite powder mixed with UV resin was compacted in the die mold and followed by alignment under the magnetic field. Effects of viscosity of UV resin and forming condition on magnetic characteristics of the compact was investigated. Maximum degree of alignment for the ferrite powder reached to 0.826. It was predicted that the proposed method had make it possible to fabricate a high performance magnet having the anisotropic alignment of the magnetic powder. The UV resin is desirable to have low viscosity, good properties such as formability and configuration stability for the compact and also parting- ability between the metal mold and the compact. (author)

Energy Technology Data Exchange (ETDEWEB)

From April 1990 through January 1991, the feasibility of recycling Navy shipboard-generated plastic wastes was explored. Normally, plastic wastes are source separated aboard Navy ships and retained for shoreside disposal in accordance with new fleet requirements implementing MARPOL Annex V that prohibits the discharge of plastics at sea. Over 23,000 pounds of shipboard plastic wastes from USS Lexington (AVT 16) and ships from the Norfolk Naval Base were recycled into park benches, picnic tables and carstops that have been distributed back to the Navy bases for use. Navy shipboard plastics must undergo sorting prior to recycling because Navy plastic waste contains large quantities of composite plastic items (e.g., plastic/paper) that are not easily recyclable. Recycling food-contaminated plastics is not practical due to sanitation problems encountered during handling. However, certain items have good resale value if separated by resin type and ...

International Nuclear Information System (INIS)

Polyamide is a modifier which introduces flexibility and toughness to phenolic foam by non reactive approach. Phenol formaldehyde resin was physically modified by the addition of polyamide in different percentages ranging from 0.05% to 0.2% which introduced toughness to modified resole. The resultant polymers were characterized by thermal and mechanical analysis using Thermogravimetric Analyzer (TGA), Instron machine and Dynamic Mechanical Analyzer (DMA). (author)

International Nuclear Information System (INIS)

The use of Chelex resin for the synthesis of radioactive lead complexes has been explored. The process involved immobilization of "2"0"3Pb on the resin and subsequent elution of complexed lead by chelating agents. "2"0"3Pb complexes derived from meso- and racemic dimercaptosuccinic acid (meso-DMSA, rac-DMSA) were prepared and assessed for stability in vitro.

International Nuclear Information System (INIS)

Recent nuclear power plants require high purity water to protect nuclear reactors or steam generators from SCC and maintain in good condition. In this connection, it is especially important to minimize sulfate, which is a corrosive chemical originated from oxidative degradation of cation exchange resins during operation. Recently, uniform particle size (UPS) strong acid cation gel resin with 14% cross-linkage, which has excellent stability against oxidization, has been applied to several condensate purification systems. For further improvement of water quality, some methods for changing the configuration of condensate demineralizer's resin bed have been examined. For example, these methods correspond to anion under layer and cation over layer. We have tested these methods by cold column tests. Furthermore, we have developed the newly anion exchange resin having higher efficiency and capacity for ...

Science.gov (United States)

Not Available

British Library Electronic Table of Contents (United Kingdom)

Abstract Flame retardants (FRs) are used for in protection against fire. Organic inorganic hybrids could become one of the most promising FR solution in the future. In this paper, the synthesis, the characterization and the use as FRs and filler of grafted titania and alumina with 2 chloroethylphosphonic acid are presented. These hybrids contain 3.8 3.24% P and have good flame retardance when they are incorporated into unsaturated polyester resins. Alumina treated with 2 chloroethylphosphonic acid performed better than titania. The advantage of this approach is the use of these hybrid materials as filler and FR, in the same time, and the increase in flame retardancy by synergistic effect between alumina phosphorus and chlorine, for unsaturated polyester resins. Copyright 2010 John Wiley & ...

International Nuclear Information System (INIS)

Anion-exchange chromatography of element 105, dubnium (Db), produced in the "2"4"8Cm("1"9F, 5n)"2"6"2Db reaction is investigated together with the homologues Nb and Ta, and the pseudo-homologue Pa in 13.9 M hydrofluoric acid (HF) solution. The distribution coefficient (K_d) of Db on an anion-exchange resin is successfully determined by running cycles of 1702 chromatographic column separations. The result clearly indicates that the adsorption of Db on the resin is significantly different from that of the homologues and that the adsorption of anionic fluoro complexes of these elements decreases in the sequence of Ta#approx#Nb>Db#>=#Pa. (orig.)

UK PubMed Central (United Kingdom)

Peak expiratory flow rate (PEFR) has been measured hourly from waking to sleeping in 29 workers with respiratory symptoms exposed to the fumes of soft soldering fluxes containing colophony (pine resin)....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In the second part of this paper the author concludes his examination of the application of thermoplastic materials and also considers alumina ceramics, cast basalt and glass, rubbers, resins and wear-resistant steels

Energy Technology Data Exchange (ETDEWEB)

Three areas have been investigated: coal liquefaction with supercritical fluids, liquefaction by extraction with high boiling liquid solvents, and the production of resins from coal-derived hydrocarbons. The processes are described.

Energy Technology Data Exchange (ETDEWEB)

Simultaneously extracted metals (SEM) and acid volatile sulfide (AVS) show the potential for toxicity on the basis of their ratio. Accordingly, the authors spiked cadmium in a range for which Cd/AVS ratios were from 0.2 to 10 in the sediment with its weight about 8 kg in each batch. Dialysis samplers with a cation ion-exchange resin (Dowex 50W-X4) collection were used in a laboratory for the determination of free cadmium concentrations in pore water of the collected sediment. When equilibrium was reached among cadmium in pore water, sediment, and ion-exchange resin, cadmium exchanged onto resin phase was regenerated with 1 N hydrochloric acid (OPTIMA grade) and determined using an atomic absorption spectrophotometer (Zeeman 5000) with a graphite furnace accessory. Cadmium determined using the dialysis sampler is considered as free cadmium which is related to the metal bioavailability toward aquatic biota. The developed ...

International Nuclear Information System (INIS)

Results of an evaluation of 18 different products that can be used as waterstops in hydraulic dams to minimize or eliminate leaks at construction joints, were discussed. The materials were tested for permeability and adherence at 23, 15 and 5 degrees C. A two-component polyurethane resin product was found to be the one that best fulfilled the evaluation criteria. It was also found that the successful injection of a borehole depends not only on selecting the product with the best performance characteristics, but also on the technique used. Hence the preparation of the resin and the pressure at which it is injected are important performance criteria. 5 refs., 6 photos, 4 figs.

International Nuclear Information System (INIS)

The following are reported: colorimetric determination of Ti in Cr, decontamination of metals by anodic dissolution, computer code for x-ray peak identification, gel-permeation chromatography of CoRezyn 1664 polyester resin, infrared monitoring of gases and vapors, particle size analysis of dusts, nondestructive analysis of Oralloy for removable alpha contamination, dissolution (digestion) of high-fired oxides, assay of U in a Pu-U alloy, measurement of oxide thickness on Pu metal by x-ray diffraction, analysis of precipitated Pu peroxide, differentiation of Dowex SBR and 11 resins, and determination of Pu solubility in simulated lung fluid.

CERN Document Server

A simple model is outlined to describe the collision of cast phenol-formaldehyde resin spheres such as the balls used in the parlor game of pocket billiards, based in part on the famous analysis of elastic collisions developed by Heinrich Hertz over 100 years ago. The analysis treats the normal and tangential components of the initial sphere's velocity independently as it collides with a stationary identical second sphere. The collective effects of these and other parameters on the trajectory of the second sphere are provided in the conclusions.

International Nuclear Information System (INIS)

Epoxy-resin based neutron shielding material, NS-4-FR, is used for spent fuel transport and/or storage cask. In this paper the outline of thermal aging test performed to evaluate the heating effect on this neutron shielding material, NS-4-FR, is introduced. The test is consisted of two kinds of thermal aging test, one is 'Basic Test' and the other is 'Block Heating Test'. The former is cooperatively performed by ten Japanese Electrical Power Companies, and the latter is done by GESC and NOF Corporation. (authors)

International Science & Technology Center (ISTC)

Metal Matrix Composites on the Basis of Nano-Materials

International Science & Technology Center (ISTC)

Development of the Method of Electrodepositing Nanostructured Composite Coatings with Improved Engineering Properties

International Nuclear Information System (INIS)

The aim of the study is to prepare ionic exchangers using the polymerization of unsaturated polyster with monomeric styrene units in a ratio of 60%: 40% respectively. The type of method involved in this preparation, is called An Emulsion Polymerization. Such type of polymerization was carried out by two techniques: chemical and irradiation techniques. The first techniques requires the formation of free radical monomers by use of methyl Ethy Ketone Peroxide capable of decomposing into free radicals upon heating, while the other technique involves the use of gamma rays (using Co-60 source) capable of activating monomers towards free radical formations. A number of very effective chemical parameters and physical factors were used and investigated throughout the reactions such as: dispersant matrix, viscosity, rate of mixing, and irradiation dose. Besides, the study has included the study of the rate of Resin Beads Swelling which is thought to be another important part ...

Energy Technology Data Exchange (ETDEWEB)

The chemical fixation of tritium in stearic acid followed by embedding the tritiated stearic acid into an epoxy resin proved to be a good method for permanent waste disposal of tritium gas. Tc-126 and Tc-136 hardener were used for this purpose. The polymerization temperature of the polymer products was found to be highly decreased by adding stearic acid and slightly decreased by adding stearic acid or by raising the temperature of the leachant medium and slightly decreased by irradiation. On the other hand, small improvement in the compressive strength of the polymer products was achieved by adding silica powder. The polymer product showed high flame points above 573 K although it contains stearic acid. DTA and TG analysis indicate that the thermal stability of polymer products containing stearic acid and silica powder is better than samples containing only stearic acid. Stearic acid was found to possess good resistance to irradiation and the amount of hydrogen and ...

Energy Technology Data Exchange (ETDEWEB)

In the stereolithography process, three dimensional parts are built layer by layer using a laser to selectively cure slices of a photocurable resin, one on top of another. As the laser spot passes over the surface of the resin, the ensuing chemical reaction causes the resin to shrink and stiffen during solidification. When laser paths cross or when new layers are cured on top of existing layers, residual stresses are generated as the cure shrinkage of the freshly gelled resin is constrained by the adjoining previously-cured material. These internal stresses can cause curling in the compliant material. A capability for performing finite element analyses of the stereolithography process has been developed. Although no attempt has been made to incorporate all the physics of the process, a numerical platform suitable for such development has been established. A methodology and code architecture have been ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Iron concentration control in feedwater is one of the most important subjects in water chemistry. Especially for the BWR plants without 100% flow volume of hollow fiber filter (HFF), rather high iron concentration in feedwater is one of the big issues as this causes relatively high radiation dose rate in drywell area. Cation exchange resins especially used in the plants with partial flow rate of HFF are expected to have the important role of capturing iron in feedwater. For this purpose, we have investigated the effective method for using iron absorption characteristics of cation exchange resin. The Cation-Over Layer method (COL) in condensate demineralizers (CD) effectively utilizes these characteristics. In order to demonstrate a performance of the cation overlay method, we had applied this method for three CD vessels at Fukushima Daiichi NPP Unit 3 for testing purpose. The result of this actual plant test indicated that the iron ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to acquire fundamental knowledge about the factors for production and the physical properties of boards when wood powder is used as the main material and powder adhesive is used as the binder in the formation of wood boards under heat and pressure. The effects of temperature for pressing, specific gravity of board, and the ratio of adhesive on bending strength, internal binding force, and size and stability against moisture are investigated. The temperature behavior at the central area of boards under heat and pressure shows similar tendency of stagnation near 140degC which increases thereafter irrespective of the temperature of the hot plate in this experiment. The bending property increases linearly when the resin content is low, and shows the tendency of leveling off gradually when the resin content is larger than 20%. Linear relation with specific gravity if obtained in the 0.6 to 1.0 specific gravity range. ...

International Nuclear Information System (INIS)

The preparation of wood-plastic combinations (WPC) using combined methods for curing intermediate products and final products is described. In the first step, impregnated wood was irradiated using doses of 1 to 10 kGy in the presence of chemical initiators of polymerization. Thereafter, curing of this partly cured impregnating mixture was accomplished in the wood at elevated temperatures with the aid of chemical initiators of polymerization. Impregnation mixtures based on unsaturated polyester resins and methyl methacrylate, and the wood species European Beech (Fagus silvatica) and Black Alder (Alnus glutinosa) were used. The results indicate that this method of preparing WPC allows substantially lower radiation doses to be used, i.e., doses in the range of 1 to 2.5 kGy. These doses gelatinate the impregnation mixture in the wood so that the subsequent curing by chemical polymerization initiators proceeds without the impregnation mixture flowing out of the wood, ...

Energy Technology Data Exchange (ETDEWEB)

The biosorption of Cu(II) from aqueous solutions by valonia tannin resin was investigated as a function of particle size, initial pH, contact time and initial metal ion concentration. The aim of this study was to understand the mechanisms that govern copper removal and find a suitable equilibrium isotherm and kinetic model for the copper removal in a batch reactor. The experimental isotherm data were analysed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well in the Langmuir isotherm. The experimental data were analysed using four sorption kinetic models - the pseudo-first- and second-order equations, the Elovich and the intraparticle diffusion model equation - to determine the best fit equation for the biosorption of copper ions onto valonia tannin resin. Results show that the pseudo-second-order equation provides the best correlation for the biosorption process, whereas the Elovich equation also fits the ...

Science.gov (United States)

We describe a method for affinity purification of sequence-specific DNA binding proteins that is fast and effective. Complementary chemically synthesized oligodeoxynucleotides that contain a recognition site for a sequence-specific DNA binding protein are annealed and ligated to give oligomers. This DNA is then covalently coupled to Sepharose CL-2B with cyanogen bromide to yield the affinity resin. A partially purified protein fraction is combined with competitor DNA and subsequently passed through the DNA-Sepharose resin. The desired sequence-specific DNA binding protein is purified because it preferentially binds to the recognition sites in the affinity resin rather than to the nonspecific competitor DNA in solution. For example, a protein fraction that is enriched for transcription factor Sp1 can be further purified 500- to 1000-fold by two sequential affinity chromatography steps to give Sp1 of an estimated 90% ...

International Science & Technology Center (ISTC)

Thermodynamic Stable Metal Compositions for Improvement of an Operational Safety of Constructional Materials under Conditions of Multifactor Loadings of an Aggressive Environment

Science.gov (United States)

... Accession Number : ADD345858. Title : Nondestructive Testing of Polymeric Composite Sandwich Panels Via the Thermographic Halo,. ...

Energy Technology Data Exchange (ETDEWEB)

A fuel composition comprising a liquid hydrocarbon fuel and a detergent amount of the product of reaction between a polyamine and a stearic acid is described.

Science.gov (United States)

... Title : DARPA Program Composition for Embedded Systems (PCES) Program Capstone Demonstration Video (Postprint) (CD-ROM). ...

Science.gov (United States)

... The ultimate compressive strength (UCS) for the HMU/BSG composite is essentially equivalent to the tensile strength exhibited by this system. ...

Science.gov (United States)

... Accession Number : ADD808679. Title : Advanced Composites for Aerospace Require Waterjet Technology. Descriptive Note : Journal article. ...

International Nuclear Information System (INIS)

A method, based on anion exchange chromatography, is presented for the isolation of "1"3"9Ce after production by a proton-induced nuclear reaction on a thick praseodymium target. After bombardment the target is dissolved in nitric acid and "1"3"9Ce oxidised to the Ce(IV) oxidation state with bromic acid. "1"3"9Ce is then separated form the praseodymium by anion exchange chromatography on a Ag MP-1 resin column in a nitric acid - bromic acid mixture. "1"3"9Ce is sorbed onto the resin column and praseodymium eluted with the acid mixture. The bromic acid is washed out of the column with nitric acid and "1"3"9Ce finally eluted with dilute nitric acid containing sulphur dioxide.

Energy Technology Data Exchange (ETDEWEB)

A simple method is presented for the separation of lead-203 from copper-backed thallium cyclotron targets. The procedure involves cation-exchange chromatography in hydrochloric acid and hydrochloric acid-acetone mixtures. Further purification involves anion-exchange chromatography in nitric acid-hydrobromic acid mixtures. A cation-exchange column containing 3.0 g of resin can handle as much as 15 g of thallium and 160 mg of copper. An anion-exchange column containing 3.0 g of resin can separate lead from up to 200 mg of thallium and 10 mg of copper. Separations are extremely sharp and less than 0.1 ..mu..g of thallium and less than 0.1 ..mu..g of copper remain in the lead-203 fraction.

British Library Electronic Table of Contents (United Kingdom)

In this study, the use of the weakly basic anion exchange resins of phenol-formaldehyde (Amberlyst A 23), polyacrylate (Amberlite IRA 67) and polystyrene (Lewatit MonoPlus MP 62) matrices for removal of the reactive dye Remazol Black B (RBB) from aqueous solution and wastewater were investigated. RBB sorption on the anion exchangers was a time dependent process. Color reduction percentiles of 75.2, 33.9 and 25.1% in wastewater treatment were found after 216 h of phase contact time with Lewatit MonoPlus MP 62, Amberlyst A 23 and Amberlite IRA 67, respectively. Inorganic salts and anionic surfactant action influenced RBB uptake by the anion exchangers. The amounts of dye retained by the anion exchangers increased with a rise in temperature. The maximum sorption capacities calculated from the...

International Nuclear Information System (INIS)

The volatility of some elements being determined in biological and environmental samples by NAA (neutron activation analysis) in case of their binding with phenolformaldehyde resin (PFR) is studied. Since the temperature is assumed to influence the volatility of elements stronger than radiation during irradiation of samples in nuclear pile the losses of Se, As, Sb, and Hg form samples on the basis of PFR after their heating at 100-300 deg C have been investigated. It is shown that the losses of Sb and As up to 300 deg C, Se up to 250 deg C, and Hg up to 150 deg C from PFR - based samples do not occur.

Energy Technology Data Exchange (ETDEWEB)

Describes a process for production of briquets for metallurgy with binder and coke fines or anthracite. The suggested binder is waste phenol resin from the production of phenol (cumene method). Resin properties are given. Possible reaction mechanisms yielding solidified matter are discussed. The production process requires 10-15% binder and applies charge heating up to 200 C over 30 min. Catalytic amounts of sodium hydroxide or sulfuric acid were also employed. The production process is shown in a flowsheet. Properties of produced briquets are tabulated. The briquets were used in a 8 t/h cupola furnace and their performance was compared to that of KL-1 coke. Performance was found to be comparable; the cost of coke briquets was less than that of heating coke. 2 refs.

British Library Electronic Table of Contents (United Kingdom)

The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...

International Nuclear Information System (INIS)

The principle for working out the time-temperature schedule of the carbonization was determined through the investigation on the carbonization process of the green body and the phenol formaldehyde resin. During the carbonization process, the crack at lower temperatures is due to strain inhomogeneity produced in press. But the crack at higher temperatures results from the improper increasing rate of temperature. The application of the autoclave-carbonization process can increase the mechanical properties of the spherical fuel elements.

Energy Technology Data Exchange (ETDEWEB)

Only two years ago, plastic film recycling was considered an onerous task. Different resins had to be identified, colors had to be separated, and minute contaminants had to be weeded out almost by hand to produce a quality material. But the tide of plastic film recycling is changing now that new technologies have emerged and more organized collection infrastructure have been developed. Today, plastic film recycling maintains a lucrative market for those with the right combination of equipment and know-how.

International Nuclear Information System (INIS)

New standardization techniques of samples in multielement instrumental neutron-activation analysis (INAA) of biological materials (BM) are considered. New methodical developments of sample preparation techniques, BM tableting, creation of comparison standards and standardization of packing material are suggested. Correlated data on concentration of different elements in standard specimens-comparison standards are presented for mass INAA, that is: for phenol-formaldehyde resin-base and human blood-base synthetic standards. 7 refs.; 3 tabs.

International Nuclear Information System (INIS)

... lutetium 177 multi-element separation niobium 105 niobium 92 nitric acid

British Library Electronic Table of Contents (United Kingdom)

A tobermorite/hydroxyapatite composite was prepared by hydrothermal treatment using diatomaceous earth, ?-tricalcium phosphate and slaked lime starting materials. The XRD patterns of the composite confirmed that tobermorite and hydroxyapatite were formed after the hydrothermal process. The bending strength of the composite reached a level higher than 9?MPa after the hydrothermal process. The development of the bending strength was due to the formation of tobermorite and hydroxyapatite during the hydrothermal process. The composite had a high specific surface area due to these newly formed crystals.

Energy Technology Data Exchange (ETDEWEB)

Effect of nitrogen-containing additives in the study of wood plastic composites of MMA with simul and mango wood of Bangladesh has been investigated. Nine different additives were used and the additives containing carboamide group induce the highest tensile strength to the composite. (author).

Science.gov (United States)

Effect of nitrogen-containing additives in the study of wood plastic composites of MMA with simul and mango wood of Bangladesh has been investigated. Nine different additives were used and the additives containing carboamide group induce the highest tensile strength to the composite.

Science.gov (United States)

This study investigated weathering effects on polyvinyl chloride (PVC) based wood plastic composites (WPC), with a focus on the color and structure that is attributed to the material composition. It is directed towards quantifying the main chemical modifi...

Energy Technology Data Exchange (ETDEWEB)

This report presents a brief description of the fabrication and advantages of a composite, carbon-metal fiber material which does not require lubrication.

CERN Document Server

Preparation of covalently modified organic-inorganic composite nanoparticles and their interfacial electron transfer researches

International Nuclear Information System (INIS)

... Commission, Rio de Janeiro Rio de Janeiro, RJ (Brazil) 26-27 Nov 1998 1

UK PubMed Central (United Kingdom)

This article addresses the need for new data on indirect effects of natural and anthropogenic aerosol particles on atmospheric ice clouds. Simultaneous measurements of the concentration and composition...Full Text Available

Science.gov (United States)

hlgh fiber content composites met the minlmum requirements. (1400 O F ) , the hlgher fiber content as-fabricated composites have impact strengths distinctly ...

Science.gov (United States)

The objectives of the Phase-I research address the development of mechanics- based structural integrity analysis methodologies for composite sandwich panels ...

Energy Technology Data Exchange (ETDEWEB)

We study the signals for composite vector leptoquarks in [ital e][sup +][ital e[minus

Science.gov (United States)

We advance a tentative composite model for computer security at JPL, together with inter and intra networking with other NASA centers and overseas clients.

Energy Technology Data Exchange (ETDEWEB)

Heat fusion is the most common joining method for polyethylene gas distribution piping. Butt fusion was studied with the intent of relating the quality of the joint to the joining conditions. A semi-empirical approach was used. The thermofluid consequences of joining conditions such as heater temperature, heating time and joining parameter were calculated using a computer model. The model was validated by instrumented tests. The strength of the joints was gauged by destructive mechanical testing. Tensile and tensile impact tests were used. Over 150 joints were fabricated using four different polyethylene resins. Most of the data are given in GRI Report No. 88/0276.2 -- Volume 2: Technical Reference on Butt Heat Fusion Joining of Polyethylene Gas Pipes. A parameter, termed the Joining Parameter, was found to characterize the joining conditions. Of the mechanical tests parameters, the impact energy was found to have the best correlation with the joining parameter. ...

Energy Technology Data Exchange (ETDEWEB)

Inexpensive activated carbon assembly(ACA) was prepared with glass fabrics coated by 10 wt%, 25 wt%, 50 wt% phenolic resin solution, followed by activation at 700{sup o} C under N{sub 2} atmosphere and subsequent surface modification with N{sub 2}, NH{sub 3}, CO{sub 2} gas, respectively. The conversion chemistry of resin to carbon was analyzed by using FT-IR, TGA, SEM, XPS, and the SO{sub 2} adsorption characteristics of the ACA were compared to that of commercial activated carbon fabrics(ACF). The ACA modified by NH{sub 3} showed the best SO{sub 2} adsorption behavior due to the presence of basic functional groups such as amine on the surface, confirmed by XPS. The ACA modified by NH{sub 3} displayed relatively high adsorption capacity of 116.5 mg/g carbon, which is corresponding to 75% adsorption of the commercial ACF(153.4 mg/g) treated with the same method. 14 refs., 6 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The effect of atmospheric pressure on tracking resistance of organic insulating materials were investigated in the range of 500 to 1007 hPa. The tracking resistance for Polycarbonate (PC), Modified Polyphenylene Oxide (M-PPO) and Paper Base Phenolic Resin Laminate (PL) increase with the decrease in atmospheric pressure. The scintillating discharges on these samples surface lead to the ignition. The tracking failure on these results from the ignition on the surface. For Polybutylene Terephthalate (PBT) and Polyethylene Terephthalate (PET), the tracking resistance decrease with the decrease in atmospheric pressure. The discharges observed on the these surface are the glow-like. The discharge area spreads on the surface between the electrodes at the lower pressure. The failure on this group results from the carbonization by the discharges on the surface. However, the tracking resistance for Unsaturated Polyester Resins (UP) has no significant ...

Energy Technology Data Exchange (ETDEWEB)

A new method for the determination of {sup 237}Np and Pu isotopes in large soil samples has been developed that provides enhanced uranium removal to facilitate assay by inductively coupled plasma mass spectrometry (ICP-MS). This method allows rapid preconcentration and separation of plutonium and neptunium in large soil samples for the measurement of {sup 237}Np and Pu isotopes by ICP-MS. {sup 238}U can interfere with {sup 239}Pu measurement by ICP-MS as {sup 238}UH{sup +} mass overlap and {sup 237}Np via {sup 238}U peak tailing. The method provides enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then transferring Pu to DGA resin for additional purification. The decontamination factor for removal of uranium from plutonium for this method is greater than 1 x 10{sup 6}. Alpha spectrometry can also be applied so that the shorter-lived {sup 238}Pu isotope can be measured successfully. {sup 239}Pu, {sup 242}Pu and {sup ...

Energy Technology Data Exchange (ETDEWEB)

This document reports the results of testing of spent ion exchange media pretreatment technologies. Emphasis of the testing activities has been on screening pretreatment technologies, such as drying and emulsification, which are compatible with vitrification, cementation, and incineration. Ion exchange media tested for cementation and incineration pretreatment technologies were typical organic ion exchange resins and inorganic zeolites. The ion exchange medium tested for vitrification pretreatment technologies was inorganic zeolite. The results of testing activities are discussed in detail in this report.

International Nuclear Information System (INIS)

This year was spent in perfecting details of the new design blood irradiator, i.e., having male fittings made for shunt insertion and in acquiring preliminary biological data on its effectiveness. Fabrication of units was slowed by an unanticipated reaction of the resin with the steel injection mold, by occasional thrombogenic flaws in the blood interface layer, by thrombus formation at the points of connection to the shunt and by nonavailability of a reactor for activating the "1"6"9Tm to "1"7"0Tm. The remaining unsolved problem is that of thrombus formation at the connectors.

International Nuclear Information System (INIS)

The reactor fuel cycle based on uranium is described. The various stages in the cycle include mining of uranium ores followed by crushing and grinding, leaching and purification of leach liquor by ion exchange resin process or solvent extraction process, refining of uranium concentrate (yellow cake) by digesting with HNO_3 and then solvent extracting uranyl nitrate with TBP, conversion of uranyl nitrate to uranium hexafluoride, production of uranium metal, uranium enrichment, fabrication of reactor fuel elements and reprocessing of the spent fuel. Chemical reactions wherever they are involved are explained. (M.G.B.).

International Nuclear Information System (INIS)

Radioactive "1"4C sucrose was found to be an ideal marker for microleakage because it did not penetrate tooth tissue, dental cement, or mounting resin. The main finding is that the adhesive cements--the glass-ionomer and polycarboxylate--are significantly more effective at preventing microleakage than are the traditional phosphate cements--silicate and zinc phosphate. The differences can be as high as two orders of magnitude. The adhesive cements provide almost perfect and reliable seals. By contrast, the nonadhesive cements are erratic sealants with most of the restorations leaking.

Energy Technology Data Exchange (ETDEWEB)

Scientists of the Institute of Wood Chemistry of the Latvian Academy of Sciences have developed two highly efficient processes for producing furfural, a feedstock for varnishes, synthetic resins and plastics. It is made of production wastes, including branches and small-dimension timber. By one process, the raw material is chipped, treated first with diluted sulphuric acid and then with steam heated to 250 degrees C. The other uses concentrated sulphuric acid as a catalyst. Besides furfural, this process also yields sugar solutions used in alcohol and nutrient yeast production.

Energy Technology Data Exchange (ETDEWEB)

A 20-cell PEFC stack was designed and built. Resin impregnated graphite was used as bipolar plate material. The air cooling of the stack was optimized by introducing high surface structures into the open space of the cooling plates. At {eta} (H{sub 2} LHV) = 0.5 a power of 880 W was obtained under conditions of low gas-pressures of 1.15 bar{sub a}. The auxiliary power for process air supply and cooling at 880 W power is less than 7% of the power output, indicating that the described system may be operated at a high efficiency. (author) 5 figs., 2 refs.

International Nuclear Information System (INIS)

The bituminzation of decontamination and ion exchange resin stripping wastes with four grades of asphalt was investigated to determine the effects of asphalt type on the properties of the final products. All waste forms deformed readily under light loads indicating they would flow if not restrained. It was observed in all cases that product leaching rates increased as the hardness of the asphalt used to treat the waste increased. If bituminization is adopted for any Ontario Hydro aqueous radioactive wastes they should be treated with soft asphalt to obtain optimum leaching resistance and mechanical stability during interim storage should be provided by a corrosion resistant container.

Science.gov (United States)

... and testing of unidirectional composites, there are serious doubts about the possibility of obtaining a true ultimate compressive strength for this kind ...

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The method of production of xAl{sub 2}O{sub 3}-yTiO{sub 2} compositions provides for the depth distribution of coating components and specifies its mechanical properties. In case of the composition obtained by cladding, titanium is mainly concentrated at the substrate. In case of mechanical mixture or composition obtained by sintering the oxides, the depth distribution of coating components is random.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... slenderness ratio. Equations which determine the ultimate compressive strength of a composite were established. Several ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Descriptors : *PROPELLING CHARGES, *NITROCELLULOSE, *COMBUSTIBLE CARTRIDGE CASES, DENSITY, FIBERS, MANUFACTURING ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The General-Purpose Heat Source (GPHS), an improved radioisotope heat source, employs a unique thermal insulation material, carbon-bonded carbon fiber (CBCF), to protect the fuel capsule and to help achieve the highest possible specific power. The CBCF insulation is made from chopped rayon fiber about 10 ..mu..m in diameter and 250 ..mu..m long, which is carbonized and bonded with phenolic resin particles. The CBCF shapes, both tubes and plates, are formed in a multiple molding facility by vacuum molding a water slurry of the carbonized chopped-rayon fiber (54 wt %) and phenolic resin (46 wt %). The molded shapes are subsequently dried and cured. Final carbonization of the resin is at 1600/sup 0/C. Machining to close tolerances (+-0.08 mm) is accomplished by conventional tooling and fixturing. The resulting material is an excellent lightweight insulation with a nominal density of 0.2 Mg/m/sup 3/ and a thermal conductivity ...

International Nuclear Information System (INIS)

Wood plastic composites are prepared under radiation of "6"0Co gamma source with simul, a low grade wood of Bangladesh using a water soluble monomer acrylamide (AM) mixed with a swelling solvent methanol, water or methanol/water (1:1) at different compositions in the presence of a number of additives and co-additives such as NVP (N-vinylpyrrolidone), TPGDA (tripropylene glycol diacrylate), TMPTA (trimethylol propane triacrylate), sulfuric acid, urea and copper sulfate. Polymer loading (PL) and tensile strength (TS) of the composites are measured. The role of these additives on the composites is also discussed. It is observed that nitrogen-atom containing-materials like urea, NVP and AM produce composites with the highest mechanical strength, and incorporation of copper into this system provides additional property of protection and preservation of the composites ...

International Nuclear Information System (INIS)

Polymerizing effects of high energy radiation has been found suitable for preparation of wood-polymer composites. In the present work after evaluating polymer products that have been obtained by irradiation method, wood-polymer composites have been prepared by in situ polymerization of vinyl acetate, acrylic acid and acrylic acid/styrene mixture using two samples of Iranian hardwoods, Beech and Hornbeam. These woods and their composites have been tested for their physical and mechanical properties. The results have shown that chemical bonding between polymer and the cell wall component lead to better strength properties in the composites. (author).

Energy Technology Data Exchange (ETDEWEB)

To study the effect of CuO on the electrochemical properties of MgNi alloy, the MgNi-xCuO (x = 3, 5 and 10 wt%) composites were prepared by ball-milling method. The X-ray diffraction (XRD) analysis showed that the structures of the composites were amorphous. The cycle stability of the composites was improved compared to pure MgNi alloy due to the enhancement of the anti-corrosion property in the alkaline electrolyte, and the composite with 5 wt% CuO ball-milled for 15 h exhibited the best performance. Electrochemical impedance spectroscopy (EIS) and potential-step measurements indicated that the electrochemical kinetics of the composites was improved.

UK PubMed Central (United Kingdom)

The purpose of this study was to assess changes in dairy herd milk production and milk composition associated with changes in Salmonella contamination of bulk milk on dairy farms in southwestern Ontario....Full Text Available

UK PubMed Central (United Kingdom)

ABSTRACTPurpose: To describe previously reported locomotor muscle and whole-body composition factors related to mobility in older individuals.Methods:...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Rheological properties of moderately concentrated solutions of cellulose in methylmorpholine N-oxide-dimethylformamide mixtures containing hydrophilic montmorillonite nanoparticles were studied. Film composite materials were prepared, and their physicomechanical properties and structural organization were studied.

Energy Technology Data Exchange (ETDEWEB)

A polyolefin composition is described comprising: 100 parts by weight of polyolefin, not less than 0.5 part by weight of a polyamide selected from the group consisting of nylon 6 and nylon 66, and from 3 to 30 percent by weight of a novolak based on the weight of the polyamide.

International Nuclear Information System (INIS)

Ca #alpha#-sialon is a high hardness material that exhibits in-situ growth of elongated grains during pressureless sintering. This potentially gives the material very good fracture toughness. This paper examined the effects of a number of variables on microstructural development during sintering. The effect of composition was investigated by studying seven different compositions. Densification was seen to be hindered in compositions that produced only small quantities of liquid phase during sintering. Elongated #alpha#-sialon was observed in all the compositions. It was in combination with equiaxed #alpha#--sialon in low liquid compositions, but only elongated #alpha#-sialon was present in the liquid rich compositions. The effects of using P-Si_3N_4 instead of #alpha#-Si_3N_4 starting powders were also examined. Compositions using only ...

Science.gov (United States)

This report documents the collaborative effort between the United States and Canada to investigate the impact of process-induced defects on strength and stiffness under static and fatigue loading and for low-cost composite aircraft structures, in particul...

UK PubMed Central (United Kingdom)

Thermal behaviors of eucalyptus wood residue (EWR) filled recycled high density polyethylene (HDPE) composites have been measured applying the thermogravimetric analysis (TGA) and differential scanning...Full Text Available

International Nuclear Information System (INIS)

This investigation clearly demonstrates that through partial impregnation techniques wood-polymer composites can be formed from the Pinus species grown in South Africa with a considerable saving in monomer costs without sacrificing the important physical properties of these materials.

Science.gov (United States)

The report gives results of an examination, including mutagenic screening, of the chemical composition of residual fuel oils and their column chromatography pre-fractions. A degree of correlation between composition and mutagenicity has been achieved. Radionuclide data has been o...

International Nuclear Information System (INIS)

Using acrylic-group containing isocyanates together with methyl methacrylate as impregnating mixture and gamma rays for curing wood-plastic composites have been produced, which show high-dimensional stability and toughness (low brittleness) compared to commonly used wood-plastics. The syntheses of proper acrylic-group containing isocyanates are as well described as the properties of the produced composites, made from maple wood. Also the direct use of the initial compounds, necessary for the syntheses, resulted in products of similar properties. These wood-plastic composites are to be suggested for the production of high-class products, e.g. wood-wind instruments. (author).

British Library Electronic Table of Contents (United Kingdom)

The load-carrying capacity and ultimate deformation capacity of timber-concrete composite systems can be significantly influenced by the ductility of the connection between the two materials. The use of more ductile connections can increase the load-carrying capacity of the composite system as well as its ultimate deformation capacity. In this work, the potential increase that might be expected for these two parameters due to the use of ductile connections will be assessed through numerical simulations, taking the non-linear behaviour of the connections into account. Furthermore, the connection ductility required to achieve the maximum load capacity depends on the mechanical properties of the connection as well as on the geometric and mechanical properties of the composite system. There ar...

Science.gov (United States)

... the Redwood Creek basin in north coastal California, timber harvest and associated streamside landsliding altered the composition ... ...

International Nuclear Information System (INIS)

One of the greatest opportunities for using of biomass as a precursor in the production of polymeric materials is the lignocellulose composites that can combine high performance with low costs. This work is a initial study on the production of a lignocellulose reinforced polyethylene composite. A compatibilization made by a induced gamma radiation grafting reaction was used to increase the adhesion between the matrix and the reinforced or filled fibers. The lignocellulose materials were exposed to gamma radiation in order to promote a molecular degradation and increase its reactivity. The polymer, the lignocellulose material and the compatibilization were processed by extrusion and the composite produced by this process were characterized by mechanical tests. (author)

Science.gov (United States)

... core section of the composite sandwich panels (Figure 5). Table 6 shows the properties that buckled as well as their initial ...

Science.gov (United States)

... Both magnesium and aluminium phosphides are therefore potentially more efficient than either calcium or sodium phosphide. ...

International Nuclear Information System (INIS)

Compositions (oligomers with suitable properties and Al, Fe, Cu, Ta, W powders) were hardured by the flux of accelerated electrons at 10 mA beam current and 1.5 MeV energy. Dielectric and mechanical properties of metal-filled polymeric compositions as well as their radioply sicl properties in SHF-range are studied. It is shown that the produced compositions belong tot he absorbing protective materials in which the protection effect is mainly achieved through the absorption losses. 6 refs.; 3 tabs.

Science.gov (United States)

... Accession Number : ADD321199. Title : OPTIMIZATION OF EDDY CURRENT PROBES FOR NDT OF CARBON FIBER COMPOSITES. ...

Science.gov (United States)

Analytical models for predicting the deformation and failure of composite sandwich panels subjected to blast and projectile impact loading are presented in this paper. The analytical predictions of the transient deformations and damage initiation in the composite sandwich panels were compared with finite element solutions using ABAQUS Explicit. For the blast model, the predicted transient deformation of the sandwich panel was within 7%of FEA results, while the predicted damage initiation using Hashin's composite failure criteria was about 15%higher than FEA results in most cases. For the high velocity impact model, the predicted transient deformations were within 20%of FEA results.

Science.gov (United States)

A sandwich construction, composed of hybrid carbon-glass fiber-reinforced plastic skins and a

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... Title : Compressive and Shear Buckling Analysis of Metal Matrix Composite Sandwich Panels Under Different Thermal Environments. ...

Science.gov (United States)

... energy absorption characteristics of composite sandwich panels, thermoplastic energy-absorbing subfloor structures, and shoulder belt pre- tensioners. ...

Science.gov (United States)

The chemical analysis of lipids of Prochloron isolated from several hosts is discussed. The object

Science.gov (United States)

A flutter-motion equation is presently derived for a 2D composite sandwich panel considering the total lateral displacement of the plate as the sum of the displacement due to bending of the plate, and that which is due to shear deformation at the core. The effects of core thickness and stacking sequence of the faces on the flutter boundary of the plate are discussed; it is shown that the sandwich panel greatly improves the flutter boundary over that of a composite laminate panel, provided it has sufficient core thickness.

Energy Technology Data Exchange (ETDEWEB)

A new method for the determination of the cmc using a dialysis technique which allows monometric species to diffuse through but no micelles has been applied for determining the mixed micelle composition. The method is based on determining the amount of surfactant that diffuses through at two different times which allows for the calculation of the cmc by use of the appropriate equation. This method requires the preparation of only one concentration of solution and lends itself particularly well to the determination of the composition of mixed micelles. (orig.)

International Nuclear Information System (INIS)

The structure and properties of composite powder coatings on the base of titanium carbide are studied. It is shown the electron-beam welding deposition of powders on the base of nickel and titanium carbide allows to produce of high-quality wear-resistant coatings which superior in density and hardness compared with sputtered ones. Changes of hardening phase volume percentage as well as composition of metal matrix make possible to control coatings hardness

Energy Technology Data Exchange (ETDEWEB)

The gas composition of recent thermal waters is in perfect conformity with their geologic-tectonic positions. The composition of gas-liquid inclusions in the basic-hyperbasic xenoliths of basaltoid lavas depends on the depth from which xenoliths are supplied. (The depth is determined by using the methods of geological thermobarometers). By comparing available data the conclusion was drawn that the gas compositions of thermal waters reflect the depth of generation of deep fluid which heats them and depends on the penetration depth of the fluid-conducting fissure zones.

International Nuclear Information System (INIS)

As part of the general QC/QA management of the k_0-standardization, three types of 'SMELS' (synthetic multi-element standards) are being developed to check the performance of k_0-NAA when implemented in a laboratory. Phenol-formaldehyde resin is proposed in this paper as the matrix of choice. Based on previous work, this material could be prepared with sufficient purity so as to make interferences with the spiking elements negligible. The matrix was found to be adequately resistant towards high neutron flux irradiation. A selection was made of compounds, soluble in ethyl alcohol, for spiking the prepolymer ethanolic solution with the elements of interest. Finally, some prototypes were prepared and a satisfactory homogeneity of the spiked elements was found for 50 mg sample intake.

Energy Technology Data Exchange (ETDEWEB)

A procedure was developed for separating rubidium from irradiated aluminum encapsulated uranium. The separations procedure produces a final ultra-high purity RbCl product for subsequent high performance mass spectrometric analysis. The procedure involves first removing most of the macro-components and fission products by strong base anion exchange using, first, concentrated HCl, then oxalic acid media and second, selectively separating rubidium from alkaline-earth ions and other alkali-metal ions, including cesium, using Bio-Rex-40 cation-exchange resin. The resultant RbCl is then put through a final vacuum sublimation step. Ultra-pure reagents and specially clean glassware are used throughout the procedure to minimize contamination by naturally-occurring rubidium.

International Nuclear Information System (INIS)

The small pilot facility of a cyclone type suspension incineration system of radioactive waste was set up in order to evaluate the decontamination efficiency of a high efficiency ceramic filter. The evaluation was made by use of "5"4Mn, "5"9Fe, "6"0Co, "6"5Zn and "1"3"7Cs. 1. The decontamination factor by one line of ceramic filter for every species were over 10"5. 2. The decontamination factor increased by one oder when water vapor exists in off-gas. The same tendency was also observed when iron dioxide existed at the incineration of cation exchange resin. (author).

Energy Technology Data Exchange (ETDEWEB)

Many higher plants produce economically important organic compounds such as oils, resins, tannins, natural rubber, gums, waxes, dyes, flavors and fragrances, pharmaceuticals, and pesticides. However, most species of higher plants have never been described, much less surveyed for chemical or biologically active constituents, and new sources of commercially valuable materials remain to be discovered. Advances in biotechnology, particularly methods for culturing plants cells and tissues, should provide new means for the commercial processing of even rare plants and the chemicals they produce. These new technologies will extend and enhance the usefulness of plants as renewable resources of valuable chemicals. In the future, biologically active plant-derived chemicals can be expected to play an increasingly significant role in the commercial development of new products for regulating plant growth and for insect and weed control. 65 references.

British Library Electronic Table of Contents (United Kingdom)

Tests using reconstituted samples have been performed to assess the diffusive transport of 137Cs and 60Co through natural regolith materials from a region in South Australia being considered for a radioactive waste repository. A double diffusion cell apparatus made of polycarbonate resin was developed to estimate the effective diffusion (De) and sorption coefficients (Kd) that allowed large withdrawals from the source and collector cells and has enabled tests with low concentrations of radioactivity. An alternative to porous stainless steel filter plates has also been used to reduce uncertainty in test interpretation. Analysis of the transient data used a staged method of the Laplace transform to take into consideration the volume of the samples withdrawn from the apparatus during testing....

International Nuclear Information System (INIS)

The losses of Hg from phenol formaldehyde resin - bound standards and hair samples in neutron activation analysis in case of their irradiation in the water filled nuclear reactor channel is studied. The mean losses of Hg during 20-30 hrs irradiation at (2-3)x10"1"8 n/cm"2 are 15-20% with their stopping at double Al-covers. The mean losses of Hg from standards at 200, 250 and 300 deg C are 30, 61 and 86% respectively and do not occur at 150 deg C after their 5 hour heating. The losses of Hg from hair samples packed in polyethylene tubes through the package walls in experimental conditions are not observed.

British Library Electronic Table of Contents (United Kingdom)

Objectives: The aim of this study was to evaluate the in vitro behaviour of all-ceramic zirconia molar crowns in regard to different core designs and marginal fit. Methods: Identically shaped methacrylate molars were prepared according to the ceramic restoration directives resulting in a 1-mm deep circular shoulder preparation. They were embedded in polymethylmethacrylate resin after covering their roots with a polyether layer to simulate periodontal mobility. The crown cores were made of yttria-stabilized zirconia veneered with a corresponding veneering ceramic. The crowns were divided into 5 groups (n=8) which differed in core design and cement gap thickness: #1: simple core, 40mm cement; #2: core with minimal occlusal support, 40mm cement; #3: core with optimized cusp support, 40mm ceme...

Energy Technology Data Exchange (ETDEWEB)

The formaldehyde surface emission monitor (FSEM) has been developed for passive non-destructive measurement of formaldehyde (CH/sub 2/O) emission rates from CH/sub 2/O resin-containing materials. It is envisaged as a potential quality control and in-situ monitoring technique. For quality control applications to pressed-wood products, strong correlations between the results of the FSEM and environmentally controlled (small scale) chamber tests were observed. The FSEM is used to measure the cumulative CH/sub 2/O emission from a finite area of pressed-wood product during a fixed test period. The final result is reported as an average CH/sub 2/O emission rate (mg CH/sub 2/O/m/sup 2/h).

British Library Electronic Table of Contents (United Kingdom)

Abstract Lysis and extraction of cells are essential sample processing steps for investigations pertaining to metabolism of xenobiotics in cell culture studies. Of particular importance to these procedures are maintaining high lysis efficiency and analyte integrity as they influence the qualitative and quantitative distribution of drug and toxicant metabolites in the intra- and extracellular milieus. In this study we have compared the efficiency of different procedures viz. homogenization, sonication, bead beating, and molecular grinding resin treatment for disruption of HT-29 colon cells exposed to benzo(a)pyrene (BaP), a polycyclic aromatic hydrocarbon (PAH) compound and a suspected colon carcinogen. Also, we have evaluated the efficiency of various procedures for extracting BaP parent c...

British Library Electronic Table of Contents (United Kingdom)

A highly sensitive and stable tris(2,2prime-bipyridyl)ruthenium(II) (Ru(bpy)32+) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)32+ immobilized in the ECL sensor by adsorption of Ru(bpy)32+ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-...

Science.gov (United States)

This study investigated the effect of board type (unmodified vs. MAPE modified) on the surface quality and thickness swelling-water absorption properties of recycled high density polyethylene (HDPE) based wood plastic composites. Additionally, two commercially available coatings (cellulosic coating and polyurethane lacquer coating) were also applied to composite surfaces and their adhesion strength, abrasion and scratch resistance, and gloss values were determined. This study showed that modification of the composites with MAPE coupling agent increased the surface smoothness and reduced the water absorption and thickness swelling of the panels. Abrasion resistance of the composites was also improved through MAPE modification. Regardless of board type, higher scratch resistance and gloss values were observed for polyurethane lacquer coated samples compared to those of cellulosic varnish coated ones. ...

International Nuclear Information System (INIS)

The patent describes a method for repairing leakage-causing cracks and fissures in a cryogenic heat exchanger. It comprises: reducing the interior pressure of the heat exchanger to a level which does not exceed the external pressure upon the hear exchanger while maintaining the temperature of the heat exchanger at a low level relative to the ambient external temperature; applying a curable liquid filler composition to the surface of the heat exchanger proximal the leakage site for seepage into the cracks and fissures located at the leakage. The composition upon a relatively short period of cure at low temperature forming a solid material which fills the cracks and fissures; curing the filler composition; and, applying a sealant composition to the surface of the heat exchanger at the filled leakage site. The sealant composition having long-term sealing performance under cyrogenic ...

Energy Technology Data Exchange (ETDEWEB)

The effect of the coated composite surface of particles on the mechanical properties of the powder bed was investigated. Polyethylene-silica surface composite powder was prepared at several coating ratios with Hybridizer. Various tests on mechanical properties of the powder bed were carried out with the prepared powder, and the following results were obtained: The ultimate tensile strength depends only on the cohesive force between particles, and the contact probability model of composite particles led to good agreement between the experimental and calculated values. The coefficient of internal friction and cohesive shear strength were influenced due to the interlocking effect of the surface roughness of composite particles. The effects of coating particles became small with dynamic properties like angle of repose. It is possible to control the mechanical properties in a step wise fashion by changing ...

British Library Electronic Table of Contents (United Kingdom)

To improve the friction and wear behavior of carbon fabric reinforced polymer composites (CFRP), nano-SiO2 was deposited on the fabric surface. The friction and wear behavior of the resulting composites were investigated on a model ring-on-block test rig. Experimental results revealed that fiber surface treatment contributed to largely improve the tribological properties of the CFRP composites. Scanning electron microscope (SEM) investigation showed that the worn surface of the surface modified CFRP composite was smoother under given load and sliding rate. Field emission scanning electron microscopy (FESEM), FTIR and X-ray photoelectron spectroscopy (XPS) studies of the carbon fiber surface showed that nanostructured Sio2 thin film can be obtained by SiO2 sols deposition, which improved th...

International Nuclear Information System (INIS)

Composite materials of synthetics (based on monomers, oligomers and thermoplastics) and of natural polymers (wood and other fibrous cellulosics) prepared by radiation processing, offer valuable structural materials with enhanced coupling forces between the components. The applied polymer chemistry of such composites shows several common features with that of radiation grafting, e.g. the polymerization rate of oligomer-monomer mixtures in wood remains in most cases proportional to the square-root of the initiating dose-rate, just as in the simultaneous grafting, demonstrating that the chain termination kinetics remain regularly bimolecular in the corresponding dose-rate ranges. In the processing experiences of such composites, low dose requirement, easy process-control, and good technical feasibility have been found for composites of wood with oligomer-monomer mixtures, for coconut fibres with ...

Energy Technology Data Exchange (ETDEWEB)

The ultrafine fibers based on the composites of polyethylene terephthalate (PET) and a series of fatty acids, lauric acid (LA), myristic acid (MA), palmitic acid (PA), and stearic acid (SA), were prepared successfully via electrospinning as form-stable phase change materials (PCMs). The morphology and thermal properties of the composite fibers were studied by field emission scanning electron microscopy (FE-SEM) and differential scanning calorimetry (DSC), respectively. It was found that the average fiber diameter increased generally with the content of fatty acid (LA) in the LA/PET composite fibers. The fibers with the low mass ratio maintained cylindrical shape with smooth surface while the quality became worse when the mass ratio is too high (more than 100/100). Moreover, the latent heat of the composite fibers increased with the increase of LA content and the phase transition temperature of the ...

Energy Technology Data Exchange (ETDEWEB)

Four species of nanocomposites organized by hydroxyapatite (HAp), hyaluronic acid (HyA), chondroitin sulfate (ChS) and type II collagen (Col), i.e. HAp/HyA, HAp/ChS, HAp/HyA/Col and HAp/ChS/Col composites, were synthesized by coprecipitation methods. The composites could retain lots of water: 40%, 32%, 42% and 58% for the HAp/HyA, HAp/ChS, HAp/HyA/Col and HAp/ChS/Col composites, respectively. Transmission electron microscopy observations revealed that the HAp/HyA and HAp/ChS composites consisted of island-like aggregations whose sizes were 300 nm in length and 30 nm in width, and 150 nm in length and 30 nm in width, respectively. In the aggregations, there were many HAp nanocrystals of 20 nm in length, and their c-axes were aligned along the respective polymer molecules through a self-organization process. Animal tests showed that chondrocyte-like cells penetrated into the HAp/ChS/Col ...

Energy Technology Data Exchange (ETDEWEB)

The ultimate goal of this research was to develop technology to convert recycled wood fiber and plastics into durable products that are recyclable and otherwise environmentally friendly. Two processing technologies were used to prepare wood-plastic composites: air-laying and melt-blending. Research was conducted in (1) developing laboratory methods for converting waste wood, wastepaper, and waste plastics into forms suitable for processing into composites; (2) optimizing laboratory methods for making composite panels from the waste materials; (3) establishing a database on the effects of formulation and bonding agent on physical and mechanical properties of composites; (4) establishing the extent to which the composites can be recycled without unacceptable loss in properties; and (5) reaching out to industry to provide education, to develop applications, and to extend the database. ...

Energy Technology Data Exchange (ETDEWEB)

The integrity of a pipeline system is determined by its weakest links which may be the joints. Heat fusion is the most common method for joining gas distribution polyethylene (PE) piping. There are procedural, thermal, and mechanical aspects of making fusion joints. Acceptable procedural aspects, such as heater calibration and cleanliness, can be assured by rigorous training and certification of the operators. Thermal and mechanical aspects consist of specifying joining conditions such as the heater temperature, heating time, and joining pressure. In the absence of procedural errors, the strength of a fusion joint should depend on the pipe material, pipe dimensions, and the thermal and mechanical joining conditions. Socket heat fusion was studied both experimentally and analytically to determine how the strength of the joint varied with the conditions under which it was made. The standard tensile impact test was modified to test socket fusion joint samples in shear. The developed shear ...

Energy Technology Data Exchange (ETDEWEB)

A new method that allows rapid preconcentration and separation of plutonium and neptunium in water samples was developed for the measurement of {sup 237}Np and Pu isotopes by inductively-coupled plasma mass spectrometry (ICP-MS) and alpha spectrometry; a hybrid approach. {sup 238}U can interfere with {sup 239}Pu measurement by ICP-MS as {sup 238}UH{sup +} mass overlap and {sup 237}Np via peak tailing. The method provide enhanced removal of uranium by separating Pu and Np initially on TEVA Resin, then moving Pu to DGA resin for additional removal of uranium. The decontamination factor for uranium from Pu is almost 100,000 and the decontamination factor for U from Np is greater than 10,000. This method uses stacked extraction chromatography cartridges and vacuum box technology to facilitate rapid separations. Preconcentration is performed using a streamlined calcium phosphate precipitation method. Purified solutions are split between ICP-MS and ...

International Nuclear Information System (INIS)

A series of separation experiment was performed in order to study a multi-functional spent fuel reprocessing process based on ion-exchange technique. The tertiary pyridine-type anion-exchange resin was used in this experiment and the mixed oxide fuel highly irradiated in the experimental fast reactor ''JOYO'' was used as a reference spent fuel. As the result, "1"0"6Ru + "1"2"5Sb, "1"3"7Cs + "1"5"5Eu + "1"4"4Ce, plutonium, americium and curium could be separated from the irradiated fuel by only three steps of ion-exchange. The decontamination factor of "1"3"7Cs and trivalent lanthanides ("1"5"5Eu, "1"4"4Ce) in the final americium product exceeded 3.9 x 10"4 and 1.0 x 10"5, respectively. The decontamination factor for the mutual separation of "2"4"3Cm and "2"4"1Am was larger than 2.2 x 10"3 for the americium product and, moreover, the content of "1"3"7Cs, trivalent lanthanides and "2"4"3Cm included in "2"4"1Am product did not exceed 2 ppm. These results prove that ...

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the role of amorphous SiO{sub 2} particles in corrosion and wear resistance of Ni-based metal matrix composite alloying layer, the amorphous nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer has been prepared by double glow plasma alloying on AISI 316L stainless steel surface, where Ni/amorphous nano-SiO{sub 2} was firstly predeposited by brush plating. The composition and microstructure of the nano-SiO{sub 2} particles reinforced Ni-based composite alloying layer were analyzed by using SEM, TEM and XRD. The results indicated that the composite alloying layer consisted of {gamma}-phase and amorphous nano-SiO{sub 2} particles, and under alloying temperature (1000 deg. C) condition, the nano-SiO{sub 2} particles were uniformly distributed in the alloying layer and still kept the amorphous structure. The corrosion resistance of ...

International Nuclear Information System (INIS)

For several decades, ceramic matrix composite have been attracted attention in advanced structural and tribological applications. Advanced structural ceramics are presently used in diverse tribological applications such as tips for ballpoint pens, precision instrument bearings and cutting tools inserts. Design and selection of ceramics for these applications require reliable data on the effects of temperature, load and environment on the tribological behavior of these ceramics. In the present work, #alpha#-sialon matrix composites reinforced with different amounts of #beta#-sialon fibers were produced with the aim of improving their toughness to increase the industrial applications. The wear properties of #alpha#-sialon matrix composites were evaluated by carried out wear tests using a pin-on-disk tribometer under dry conditions. The #alpha#-sialon matrix composites were manufactured by slip casting and ...

International Nuclear Information System (INIS)

General estimates and references are made in connection with the role of technological physics in obtaining materials with specific features. The first part of the paper presents the modification of weak wood essences as well as technological processes at bench-scale and semi industrial scale of wood-plastic composites, under various irradiation conditions. Two technological installations for the fabrication of wood-plastic composites on both scales with technical and practical specifications of their performances are presented. Experimental data for different wood-plastic composite systems using some local wood essences in combination with several polymer and copolymer systems are given. Impregnation and polymerization levels are mentioned for every specific system. The radiation dose rate and integrated dose are given for every experimental polymerization system. The features of the wood-plastic ...

International Nuclear Information System (INIS)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been ...

International Nuclear Information System (INIS)

Researches on oil palm empty fruit bunch (EFB) fibers and thermoplastic composites have been carried out by many workers in the last decade. The main focus was to enhance the properties of the resultant composites in view of the incompatibility of the two components. Thus, efforts have been made to enhance their properties by using coupling agents, treating the fibers and modifying the matrices. In this study, the effects of electron beam (EB) irradiation and some reactive additives (RAs) on the mechanical properties of EFB-PP (polypropylene) composites were evaluated. Different modes of irradiation were investigated. Mono, di and tri functional of monomers of RAs were used. irradiating PP alone, compared to irradiating the EFB fibers or irradiating both components, gave optimum properties for EFB-PP composites. Further, improvements of the properties of the composites were achieved ...