Energy Technology Data Exchange (ETDEWEB)

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x10{sup 19} n {omega} cm{sup -1}. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual {sup 32}P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neutron transmutation doping of the initially ...

British Library Electronic Table of Contents (United Kingdom)

The neutron transmutation doping (NTD) method was applied to the initially p-type silicon in order to extend the NTD applications at HANARO. The relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material was investigated. The proportional constant between the neutron fluence and the resistivity was determined to be 2.3473x1019ncm-1. The deviation of the final resistivity from the target for almost all the irradiation results of the initially p-type silicon ingots was at a range from -5% to 2%. In addition, the burn-up effect of the boron impurities, the residual 32P activity and the effect of the compensation characteristics for the initially p-type silicon were studied. Conclusively, the practical methodology to perform the neut...

International Nuclear Information System (INIS)

Neutron transmutation doping(NTD) for producing ntype silicon semiconductor is based on the conversion of the Si-30 isotope into phosphorus atom by neutron absorption reaction. By using this method, silicon semiconductors with extremely uniform n-type dopant distributions can be produced, and this is the dominant advantage of NTD compared with the conventional chemical doping. HANARO has two vertical holes for NTD, and the commercial NTD service for 5 and 6 inch silicon ingots has been going on at the NTD2 hole. Generally, NTD method is applied to the initially n-type silicon material. But, an initially p-type silicon material can also be used for the production of uniformly doped n-type silicon by using NTD method. Therefore, in this work, we investigated the relationship between the irradiation neutron fluence and the final resistivity of the initially p-type silicon material. ...

Science.gov (United States)

The authors present electric-field dependent electroreflectance and photocurrent spectra of visible-bandgap In{sub x}(Al{sub y}Ga{sub 1{minus}y}){sub 1{minus}x}P/In{sub x{prime}}(Al{sub y{prime}}Ga{sub 1{minus}y{prime}}){sub 1{minus}x{prime}}P multiple-quantum-well (MQW) structures. These structures, grown by metal-organic vapor phase epitaxy on 6{degrees}-misoriented (100) GaAs substrates, have undoped MQWs sandwiched between doped In{sub 0.5}Al{sub 0.5}P layers, forming p-i-n diodes. Quantum-well compositions in the range 0.46{le}x{le}0.52 and 0{le}y{le}0.4, corresponding to bandgaps in the red to yellow-green range, were used. The Stark shifts in these various samples were measured and found to depend on the details of the Mg p-type doping profile, confirming important diffusion effects, in agreement with secondary ion mass spectrometry and capacitance-voltage data. The results show that these new materials are promising ...

International Nuclear Information System (INIS)

A systematic study for the materials design of III-V and II-VI compound-based ferromagnetic diluted magnetic semiconductors is given based on ab initio calculations within the local spin density approximation. The electronic structures of 3d-transition-metal-atom-doped GaN and Mn-doped InN, InP, InAs, InSb, GaN, GaP, GaAs, GaSb, AlN, AlP, AlAs and AlSb were calculated by the Korringa-Kohn-Rostoker method combined with the coherent potential approximation. It is found that the ferromagnetic ground states are readily achievable in V-, Cr- or Mn-doped GaN without any additional carrier doping treatments, and that InN is the most promising candidate for high-T_C ferromagnet. A simple explanation of the systematic behavior of the magnetic states in III-V and II-VI compound-based diluted magnetic semiconductors is also given. It is also shown that V or Cr-doped ZnS, ZnSe, and ZnTe are ...

Energy Technology Data Exchange (ETDEWEB)

Atomic layer epitaxy (ALE) was used to grow several components of the cascade solar cell structure in the AlGaAs/GaAs system. An ALE reactor was constructed for multiwafer growth with a growth rate of 0.6 {mu}m h{sup -1}. Device quality GaAs and Al{sub x}Ga{sub 1-x}As films were grown with p-type background carbon doping in the ranges 10{sup 16}-10{sup 19} cm{sup -3} and 10{sup 16}-10{sup 20} cm{sup -3} respectively. N-type films were achieved by SiH{sub 4} doping, producing carrier concentrations in the range 10{sup 16}-10{sup 18} cm{sup -3}. In addition, the potential applications of the ALE technique in the photovoltaic field are discussed. (orig.).

Science.gov (United States)

By applying lock-in thermography imaging, light-beam-induced current imaging, electron-beam-induced current imaging at different stages of sample preparation, and infrared light microscopy in transmission mode, the physical nature of the dominant material-induced shunts in multicrystalline solar cells made from p-type silicon material has been investigated. It turns out that these shunts are due to silicon carbide (SiC) filaments, which grow preferentially in grain boundaries and cross the whole cell. These filaments are highly n-type doped, like the emitter layer on the surface of the cells. They are electrically connected both with the emitter and with the back contact, thereby producing internal shunts in the solar cell.

British Library Electronic Table of Contents (United Kingdom)

By applying lock-in thermography imaging, light-beam-induced current imaging, electron-beam-induced current imaging at different stages of sample preparation, and infrared light microscopy in transmission mode, the physical nature of the dominant material-induced shunts in multicrystalline solar cells made from p-type silicon material has been investigated. It turns out that these shunts are due to silicon carbide (SiC) filaments, which grow preferentially in grain boundaries and cross the whole cell. These filaments are highly n-type doped, like the emitter layer on the surface of the cells. They are electrically connected both with the emitter and with the back contact, thereby producing internal shunts in the solar cell.

Energy Technology Data Exchange (ETDEWEB)

A brief survey is given of some recent results on doping of 4H- and 6H-SiC by ion implantation. The doses and energies used are between 10{sup 9} and 10{sup 15} cm{sup -2} and 100 keV and 5 MeV, respectively, and B and Al ions (p-type dopants) are predominantly studied. After low dose implantation ({<=}10{sup 10} cm{sup -2}) a strong compensation is observed in n-type samples and this holds irrespective of implantation temperature up to 600 C. However, at higher doses (10{sup 14}-10{sup 15} Al/cm{sup 2}) the rate of defect recombination (annihilation) increases substantially during hot implants ({>=}200 C), and in these samples one type of structural defect dominates after post-implant annealing at 1700-2000 C. The defect is identified as a dislocation loop composed of clustered interstitial atoms inserted on the basal plane in the hexagonal crystal structure. Finally, transient enhanced diffusion (TED) of ion-implanted boron in ...

International Nuclear Information System (INIS)

The shell integrity near peak compression of spherical implosions using the 60-beam, 30-kJ UV OMEGA laser system [Opt. Commun. 133, 495 (1997)] has been measured. Hot core emission backlights a shell with a thin titanium-doped layer that is imaged at x-ray photon energies above and below the titanium K edge. The x-ray intensity ratio between the two images is related to perturbations in the cold, or absorbing, part of the shell. The measured cold-shell areal-density modulations, integrated over the time of peak compression, are of the order of 25% to 50% with nonuniformity spectra peaked at spatial wavelengths of 30 to 50 #mu#m and with the smallest detectable nonuniformity features extending down to spatial wavelengths of 12 to 15 #mu#m. Hot-shell areal-density modulations of the emitting part of the shell (inner edge) are of the order of 13% to 20%. The measured shell modulations are in agreement with ...

British Library Electronic Table of Contents (United Kingdom)

This study investigates the applicability of n-type TiO2 and p-type NiO on the FTO-glass (Fluorine doped tin oxide, SnO2:F) substrate of the working electrode in a dye-sensitized solar cell (DSSC). The working electrode was designed and fabricated by depositing a film of TiO2/NiO composite particles, which were prepared by mixing the Ni powder with TiO2 particles using dry mixing method, on a FTO-glass substrate using a spin coating process. The working electrode was then immersed in the solution of N-719 (Ruthenium) dye at a temperature of 70degreeC for 6h. Moreover, a thin film of platinum (Pt) was deposited on the FTO-glass substrate of the counter electrode using an E-beam evaporator. Finally, the DSSC was assembled, and the short-circuit photocurrent, the open-circuit photovoltage and...

Science.gov (United States)

Ion implantation has been applied to magnesium-doped Al[sub 0.5]In[sub 0.5]P to produce high resistivity regions for the first time. Hydrogen, oxygen, and argon ions were implanted at a base dose ranging from 5[times]10[sup 12] to 5[times]10[sup 14] cm[sup [minus]2] and annealed from 400 to 900 [degree]C. Hydrogen did not appreciably compensate the In[sub 0.5]Al[sub 0.5]P layer while oxygen and argon produced sheet resistances up to 1[times]10[sup 9] [Omega]/[open square]. After annealing at 800 [degree]C, regions with high dose oxygen implants maintained a sheet resistance above 1[times]10[sup 7] [Omega]/[open square], while regions with high dose argon implants recovered most of the unimplanted conductivity.

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

As the only non-polar plane the (110) surface has a unique role in GaAs. Together with Silicon as a dopant it is an important substrate orientation for the growth of n-type or p-type heterostructures. As a consequence, this thesis will concentrate on growth and research on that surface. In the course of this work we were able to realize two-dimensional electron systems with the highest mobilities reported so far on this orientation. Therefore, we review the necessary growth conditions and the accompanying molecular process. The two-dimensional electron systems allowed the study of a new, intriguing transport anisotropy not explained by current theory. Moreover, we were the first growing a two-dimensional hole gas on (110) GaAs with Si as dopant. For this purpose we invented a new growth modulation technique necessary to retrieve high mobility systems. In addition, we discovered and studied the metal-insulator transition in thin bulk ...

Energy Technology Data Exchange (ETDEWEB)

The effects of dilute impurity doping on charge-density wave (CDW) structures and gaps in NbSe{sub 3} 1T-TaS{sub 2} and 2H-NbSe{sub 2} have been studied by using a scanning tunneling microscope (STM) operating at 4.2 K. In Fe doped samples of NbSe{sub 3} the STM spectroscopy measurements indicate that the added impurities can significantly shift the CDW energy gaps. In NbSe{sub 3}, Fe reduces both CDW gaps by 25-30%, and produces changes in the conductance structure relative to the pure material. The images of Fe{sub 0.01}NbSe{sub 3} show that all three surface chains in the unit cell still carry a strong CDW modulation with no evident disorder. However, a change in the relative amplitudes of the high and low temperature CDWs is detected. The effects of Co and Ni impurities on the gaps in NbSe{sub 3} have also been studied. While Co increases both by 25-30%, Ni increases only the high temperature gap with the low ...

Science.gov (United States)

is 10 seconds for P-type silicon material,. TO ,. In ordkr to determine the effects of unbalanced ionization between the two ...

Science.gov (United States)

We present results from the first studies of electric-field effects on optical transitions in visible-band-gap InGaP/InAlGaP multiple-quantum-well (MQW) structures. These structures, grown at 775 [degree]C by metalorganic vapor phase epitaxy on (100) GaAs substrates misoriented 6[degree] towards P(111)[r angle][l angle]111[r angle]A, consist of nominally undoped MQWs surrounded by doped In[sub 0.49]Al[sub 0.51]P cladding layers to form [ital p]-[ital i]-[ital n] diodes. The Stark shifts of various allowed and forbidden quantum-well transitions were observed in bias-dependent electroreflectance spectra of In[sub 0.49]Ga[sub 0.51]P/In[sub 0.49](Al[sub 0.5]Ga[sub 0.5])[sub 0.51]P MQW samples with 10-nm-thick layers. We find the magnitude of these shifts to depend on the details of the Mg doping profile, confirming the importance of Mg diffusion and unintentional background doping in these materials. Our results show that ...

International Nuclear Information System (INIS)

This study demonstrates amplified spontaneous emission (ASE) of the ultraviolet (UV) electroluminescence (EL) from ZnO at #lambda##approx#380 nm in the n-ZnO/ZnO nanodots-SiO_2 composite/p- Al_0_._1_2Ga_0_._8_8N heterojunction light-emitting diode. A SiO_2 layer embedded with ZnO nanodots was prepared on the p-type Al_0_._1_2Ga_0_._8_8N using spin-on coating of SiO_2 nanoparticles followed by atomic layer deposition (ALD) of ZnO. An n-type Al-doped ZnO layer was deposited upon the ZnO nanodots-SiO_2 composite layer also by the ALD technique. High-resolution transmission electron microscopy (HRTEM) reveals that the ZnO nanodots embedded in the SiO_2 matrix have diameters of 3-8 nm and the wurtzite crystal structure, which allows the transport of carriers through the thick ZnO nanodots-SiO_2 composite layer. The high quality of the n-ZnO layer was manifested by the well crystallized lattice image in the HRTEM picture and the low-threshold ...

International Nuclear Information System (INIS)

Polish 2001 p. 105 Poland Bogacz, J. Budzanowski, M. Mazur, J. Swakon,

Science.gov (United States)

... by the boron doping in most of the alloys except for Al66Mn9Zr25 + 50 ppm B alloy; permanent deformation at ultimate compressive strength is not ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Web Security and Online Identity Theft

Science.gov (United States)

... Tunable semiconductor lasers are essential components for links employing optical frequency modulation (OFM) for enhanced dynamic range or ...

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

... defects doped materials germanium infrared radiation monocrystals neutron

Science.gov (United States)

Counting characteristics of X-ray detectors fabricated from indium-doped, gallium-doped, and chlorine-doped CdTe have been investigated. The detectors fabricated from indium-doped and gallium-doped crystals showed radiation-induced polarization, namely, a progressive decrease of count rate with an increase of photon fluence in the high-photon-fluence region, while the detectors fabricated from chlorine-doped crystals did not. Results from current-voltage characteristics of the detectors indicated that the different counting characteristics of these detectors originated from the difference in internal electric fields in each detector.

Science.gov (United States)

of the supplier of pulled p-type silicon material. of G-6 and E 8 centers irradiated in the 1 t o 3 MeV range. tions w i l l be performed using the General ...

International Nuclear Information System (INIS)

We report on the transport properties of a high mobility two-dimensional hole system (2DHS) confined in GaAs/AlGaAs quantum wells grown by molecular-beam epitaxy on the (100) surface of GaAs. The quantum wells are modulation doped with carbon utilizing a resistive filament source. At T=0.3 K and carrier density p=1x10"1"1 cm"-"2, a mobility of 10"6 cm"2/Vs is achieved. At fixed carrier density p=10"1"1 cm"-"2, the mobility is found to be a nonmonotonic function of the quantum well width. The mobility peaks at 10"6 cm"2/Vs for a 15-nm well and is reduced for both smaller and larger well widths for these (100) samples. The mobility anisotropy is found to be small. Mobility along [011] is approximately 20% higher than along the [011] direction. In addition, the low-temperature carrier density is found to have low sensitivity to light. The hole density increases by only #approx#10% after exposure to red light at T=4.2 K. In structures designed for ...

Energy Technology Data Exchange (ETDEWEB)

Fe-sheathed MgB{sub 2} tapes with cheap stearic acid, Mg stearate and Zn stearate doping were prepared through the in situ powder-in-tube method. It is found that J{sub c}, H{sub irr} and H{sub c2} were significantly enhanced by doping. Compared to the pure tapes, J{sub c} for all the doped samples was improved by more than an order of magnitude in a high-field regime. At 4.2 K, the transport J{sub c} reached 2.02 x 10{sup 4} A cm{sup -2} at 10 T for the Zn stearate doped tapes and 3.72 x 10{sup 3} A cm{sup -2} at 14 T for the stearic acid doped samples, respectively. Moreover, at 20 K, H{sub irr} for the Zn stearate doped tape achieved 10 T, which is comparable to that of the commercial NbTi at 4.2 K. The improvement of J{sub c}-H properties in doped samples can be attributed to the increase of H{sub c2} resulting from the incorporation of ...

Energy Technology Data Exchange (ETDEWEB)

The sharp, temperature induced, continuous valence transition in EuPd/sub 2/Si/sub 2/ is drastically changed by doping with Sn at the Si site up to 5 at.%. Only a first order valence transition occurs for a 3% Sn doped sample and the 2/sup +/ component which survives the valence transition orders magnetically at 4.2 K. No valence transition at all occurs for a 5% Sn doped sample right up to 1.9 K and magnetic ordering sets in around 30 K.

International Nuclear Information System (INIS)

This paper describes the design of PMT readout module for detector prototype of Daya Bay Reactor Neutrino Experiment. According to the design requirements of the readout module, the basic structure of the readout module is discussed. This paper also discusses how to realize the charge measurement and time measurement and data processing using a high performance FPGA. The DAQ system including three readout modules and one trigger module are well commissioned and doing data taking now. (authors)

CERN Document Server

A conceptual design for the module design and disc support structure for the ATLAS forward SCT tracker

International Nuclear Information System (INIS)

Coaxial nanocables with a single-crystalline zinc telluride (ZnTe) nanowire core and an amorphous silicon oxide (SiO_x) shell have been synthesized via a simple one-step chemical vapor deposition (CVD) method on gold-decorated silicon substrates. The single-crystal ZnTe nanowire core is in zinc-blende structure along the [111] direction, while the uniform SiO_x shell fully covers the core with no observable pin-hole or crack. Formation mechanisms of the ZnTe-SiO_x nanocables are discussed. The ZnTe nanowire core shows p-type electrical properties while the SiO_x shell acts as an effective insulating layer. The ZnTe-SiO_x nanocables may have potential applications in nanoscale devices, such as p-type FETs and nanosensors.

Energy Technology Data Exchange (ETDEWEB)

Vanadium doped manganese bi-oxide has been obtained from a solution containing both cations. The X-ray diffraction of this material indicates a rutile-type phase but the enlargement of some lines supports the existence of several lattice defects. Also the particle size of the doped material is significantly smaller than the one of the non-doped material obtained in the same conditions. The presence of pentavalent vanadium inside the lattice leads to a small amount of trivalent manganese. Electron microscopy shows the existence of defects which have a tendency of becoming well-ordered and to stabilize a sur-structure. At ambient temperature, the electrochemical behaviour of doped manganese bi-oxide is greatly improved when compared to the non-doped phase. This behaviour is due to the presence of numerous lattice defects and to the smaller size of crystallites. In polymer batteries, ...

Science.gov (United States)

Seasonal Allergic Rhinitis

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

Recently a new method of controlling the pulse length of a short-pulse free-electron laser (FEL) has been developed. By modulating the synchronism between the optical and electron pulses in the FEL cavity, it was found that the output power and the micropulse length of the FEL beam oscillates at the modulation frequency. In this paper, we study theoretically the behavior of the micropulse length, both in the high loss (steady state) regime and the low loss (limit cycle) regime, when a modulated desynchronism is applied. In order to do this, we analyze the dynamics of a short-pulse FEL oscillator. The modulation frequency value plays an important role in the dynamics. We find that there is a resonantlike phenomenon between the externally applied desynchronism modulation and the limit cycle oscillation without modulation of a free-electron laser.

Energy Technology Data Exchange (ETDEWEB)

New techniques were developed to construct Schottky barrier and homojunction solar cells on GaAs substrates. Schottky barrier metal-semiconductor solar cells were produced for the first time on p-type GaAs substrate using a sputter-deposition method to form the barrier. The sputter deposition of gold or gold/palladium is the key to the method since normal thermal evaporation of gold onto p-type GaAs produces ohmic contacts. The results of this investigation are consistent with the idea that sputter damage produces donor type surface states on GaAs. Barrier heights were measured for both p-type sputtered and n-type thermally evaporated diodes using current-voltage and capacitance-voltage methods. Deep-level transient spectroscopy was used to identify the trap center concentration and energy levels for both diodes in an effort to explain the relatively large dark current in the p-type sputtered diodes. ...

Energy Technology Data Exchange (ETDEWEB)

This study is devoted to the formation of high-low-level-doped selective emitter for crystalline silicon solar cells for photovoltaic application. We report here the formation of porous silicon under chemical reaction condition. The chemical mixture containing hydrofluoric and nitric acid, with de-ionized water, was used to make porous on the half of the silicon surface of size 125 x 125 cm. Porous and non-porous areas each share half of the whole silicon surface. H{sub 3}PO{sub 4}:methanol gives the best deposited layer with acceptable adherence and uniformity on the non-porous and porous areas of the silicon surface to get high- and low-level-doped regions. The volume concentration of H{sub 3}PO{sub 4} does not exceed 10% of the total volume emulsion. Phosphoric acid was used as an n-type doping source to make emitter for silicon solar cells. The measured emitter sheet resistances at the high- and ...

Science.gov (United States)

The behavior of a small power system consisting of two interconnected generators is simulated in real-time by a prototype Digital Transient Network Analyzer (TNA). The prototype Digital TNA consists of two Computational Modules and one I/O Module. The Modules communicate with each other through ribbon cables. Each Computational Module simulates one Turbo-Generator, its Transformer, its Governor, Exciter, and Power System Stabilizer Systems. The numerical integration is shared by two TMS320C30 DSPs at a step-size of 100 microseconds in real-time. The I/O module post-processes the state variables and presents selected information for analog display. The paper presents oscillograms from a test program which includes symmetry checks and behavioral checks against well known waveforms of hunting oscillations, synchronization out-of-phase torques, and subsynchronous resonance phenomena. ...

British Library Electronic Table of Contents (United Kingdom)

Rare-earth oxides are doped into ZnO varistors as grain growth inhibitors for increasing the varistors' voltage gradients. However, their leakage currents become large and their nonlinear coefficients decrease at the same time. The reasonable explanation for such a phenomenon has not yet been available. In this paper, the temperature dependences of varistor samples' leakage currents are investigated, which reveal that the increased leakage currents of ZnO varistors with Y2O3 doping are mainly due to the bypass paths through the intergranular materials at grain corners.

International Nuclear Information System (INIS)

Equivalent circuit and electrical parameters for H-doped NH_4UO_2PO_4.3H_2O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).

International Nuclear Information System (INIS)

(1973). United Kingdom Baldwin, TO Dunn, JE Southern Illinois Univ.,

British Library Electronic Table of Contents (United Kingdom)

N-doped TiO2 has been prepared by use of sol?gel systems containing titanium alkoxide, with nitric acid as the nitrogen source. The time needed for gelation of the systems was drastically reduced by ultrasonic irradiation. The peaks assigned to the nitrate and nitrous ions were observed by FT-IR measurement during the sol?gel reaction. The N-doping was confirmed by the observation of N?O peaks in the XPS spectrum of the sample heated at 400??C. The nitrate ion acted as an oxidizer of the ethanol solvent and titanium species. The TiO2 became doped with nitrogen oxide species as a result of reduction of nitrate ion incorporated into the dried gel samples. These results indicated that the added nitric acid was reduced during the sol?gel transition and heating process, and the resulting NO spe...

International Nuclear Information System (INIS)

The highest equilibrium free-carrier doping concentration possible in a given material is limited by the ''pinning energy'' which shows a remarkable universal alignment in each class of semiconductors. Our first-principles total energy calculations reveal that equilibrium n -type doping is ultimately limited by the spontaneous formation of close-shell acceptor defects: the 3- -charged cation vacancy in AlN, GaN, InP, and GaAs and the 1- -charged DX center in AlAs, AlP, and GaP. This explains the alignment of the pinning energies and predicts the maximum equilibrium doping levels in different materials. (c) 2000 The American Physical Society

British Library Electronic Table of Contents (United Kingdom)

Heavily doped emitters with low saturation current density are of particular interest for selective emitter solar cells. These emitters can be obtained by laser doping through the phosphosilicate glass layer formed after thermal diffusion from POCl3 gas. The experimental results show that in contrast to purely POCl3 furnace-diffused emitters, the saturation current density of laser-doped emitters does not increase linearly as sheet resistance decreases, but rather features two distinct regimes. In one of these regimes, the saturation current density is found to decrease as the sheet resistance decreases, reaching values lower than those of furnace emitters. This peculiar behaviour was explained by both qualitative analysis and numerical simulations.

Energy Technology Data Exchange (ETDEWEB)

In order to discuss effects of lithium iodide (LiI) doping on condensation structure of brown coals during heating, spectral changes were measured by using an in-situ FT-IR. It was found that the LiI doping accelerates weight reduction due to heating, and the doping effect is affected by coal structure. Both of Loy Yang (LY) coal and its LiI doped coal (DLY) had absorption intensity of the FT-IR spectra decreased with rising temperature, and the absorption center belonging to an OH group shows different shifts between the LY and DLY coals. This indicates that the LiI doping has affected the change in hydrogen bonding patterns associated with heating. Both of South Banko (SB) and LY coals had the absorption spectral intensity in the OH group decreased as the weight reduction (conversion) rate increased. Reduction in the OH groups associated with heating is caused by volatilization ...

International Nuclear Information System (INIS)

A study has been made of B transient enhanced diffusion (TED) in heavily P-doped Si using secondary ion mass spectroscopy (SIMS) and positron annihilation spectroscopy (PAS). The P-doped silicon was implanted with boron ions of 40 keV energy to a dose of 3 x 10"1"4 cm"-"2, and then annealed at temperatures ranging from 700--1,000 C in a N_2 ambient for varying durations. As P doping concentration increased from 3 x 10"1"9 to 1 x 10"2"0 cm"-"3, boron diffusivity and the immobile boron fraction decreased. The experimental results are inconsistent with the predictions of the Fermi-level model and suggest that the clustering between B atoms and Si interstitials should be invoked in order to explain the immobile portion of the B peak during TED.

International Nuclear Information System (INIS)

Dy doped #alpha#-SiAlON ceramics prepared by the hot-pressing method show a high optical transmittance value, >70%, in the infrared region of 1.5-4.5 #mu#m. First principles calculations have been carried out to reveal the underlying transparency mechanism. It is found that the valence shell of doped Dy atoms interacts strongly with the doping states of #alpha#-SiAlON, resulting in the increase in the optical gap from 0.4 to 1.1 eV, which suppresses the photoabsorption in the wavelength region longer than 1.0 #mu#m and leads to the good transparency property. The calculated optical transmission spectra are in good agreement with the corresponding experiments.

Energy Technology Data Exchange (ETDEWEB)

A module is described with a receiver having a solar energy acceptance opening and supported by a mounting ring along the optic axis of a parabolic mirror in coaxial alignment for receiving solar energy from the mirror, and a solar flux modulator plate for varying the quantity of solar energy flux received by the acceptance opening of the module. The modulator plate is characterized by an annular, plate-like body, the internal diameter of which is equal to or slightly greater than the diameter of the solar energy acceptance opening of the receiver. Slave cylinders are connected to the modulator plate for supporting the plate for axial displacement along the axis of the mirror thereby shading the opening with respect to solar energy flux reflected from the surface of the mirror to the solar energy acceptance opening.

Energy Technology Data Exchange (ETDEWEB)

This research report for the Swiss Federal Office of Energy (SFOE) presents the results of a project that examined the feasibility of setting up 'MINERGIE' low-energy-consumption module standards for the production of heat in small residential buildings. The aims of the standards and the basic idea behind the MINERGIE-modules are discussed. The concepts of the modules for heat pumps and wood-fired heating systems and their combination with solar installations are examined, as are their areas of application. The requirements placed on the modules are listed. System concepts, including simple schematics for typical installations, are presented for wood-log, wood-chippings and pellets-fired systems as well as for ground-loop and air-water heat pump systems as well as their solar-aided counterparts. The results of cost-benefit analyses are presented and questions regarding system guarantee ...

UK PubMed Central (United Kingdom)

The GABA-modulating and GABA-mimetic activities of the monoterpenoid thymol were explored on human GABA_A and Drosophila melanogaster...Full Text Available

UK PubMed Central (United Kingdom)

We have measured the forward and reverse rates of the allosteric transition of hemoglobin A with three CO molecules bound by using modulated excitation coupled with fluorescence quenching of the DPG...Full Text Available

UK PubMed Central (United Kingdom)

Many lifespan-modulating genes are involved in either generation of oxidative substrates and end-products, or their detoxification and removal. Among such metabolites, only lipoperoxides have the ability...Full Text Available

UK PubMed Central (United Kingdom)

Intensity modulated radiotherapy (IMRT) is widely used in clinical applications in developed countries, for the treatment of malignant and non-malignant diseases. This technique uses multiple radiation...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundTo compare the differences in dose-volume data among coplanar intensity modulated radiotherapy (IMRT), noncoplanar IMRT, and helical tomotherapy (HT) among patients with...Full Text Available

International Nuclear Information System (INIS)

A new kind of e-beam bunching enabling the production of coherent spontaneous emission (CSE) is proposed and considered. It is shown that an e-beam in passing through an undulator will induce CSE along with incoherent spontaneous radiation on the same wavelength if the e-beam transverse velocity is modulated with a spatial period twice as long as the radiation wavelength. Such angular modulated beams can be regarded as alternatives to conventionally density modulated beams for CSE production. Requirements for e-beams are similar in both cases.

Science.gov (United States)

... concentrated on the construction of switches using fiber ... been chosen for a switch realized in ... of these techniques using acousto-optic modulators or ...

International Nuclear Information System (INIS)

Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized under a high magnetic field of 10 T. The formation mechanism was investigated and discussed in detail. The synthesized samples were characterized by XRD, SEM, TEM, EMPA, and vector network analysis. By doping MnO2 with Fe, the relative complex permittivity of MnO2 and its corresponding loss tangent clearly decreases, but its relative complex permeability and its corresponding loss tangent markedly increases. Moreover, the theoretically calculated values of reflection loss show that with increasing the Fe content, the as-prepared Fe-doped MnO2 exhibits good microwave absorption capability. -- Graphical Abstract: Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized in a high magnetic field of 10 T via a simple chemical process. Display Omitted Highlights: ? Fe-doped MnO2 ...

Energy Technology Data Exchange (ETDEWEB)

The properties of Mn-doped GaAs layers grown by laser deposition were investigated with measurements of Hall effect and magneto-optical Kerr effect (MOKE). The electrical and magnetic parameters of the layers were defined by growth temperature and quantity of sputtered Mn. It was shown that room-temperature ferromagnetism is revealed by MOKE and, after ruby laser 25 ns pulse annealing, by Hall effect measurements.

International Nuclear Information System (INIS)

The doping of deuterated polyparaphenylene [C_6D_4]sub(n) with AsF_5 has been investigated by real time neutron diffractometry at 100, 400 and 820 mbar AsF_5 pressure. The reaction appears to be diffusion controlled. Evidence for one doped phase with partial crystalline order was obtained. Structural considerations suggest two polymer chains plus one dopant ''string'' as the repetitive unit. (Auth.).

International Nuclear Information System (INIS)

We study quasifinite highest weight modules over the supersymmetric extension of the W_1_+_#infinity# algebra on the basis of the analysis by Kac and Radul. We find that the quasifiniteness of the modules is again characterized by polynomials, and obtain the differential equations for highest weights. The spectral flow, free field realization over the (B, C)-system, and the embedding into gl(#infinity#vertical stroke #infinity#) are also presented. (orig.).

Science.gov (United States)

The mz8310 device support module provides support for the following record types: event, pulseCounter, pulseDelay, and pulseTrain. No driver support is needed. Up to 4 mz8310 modules are supported. Each 8310 module contains 10 channels, which are identified as signals O,...9. Each channel is individually configurable. Each mz83 10 has two Am9513 Timing Controller chips. Each Am9513 has 5 counters.

British Library Electronic Table of Contents (United Kingdom)

Previously, we demonstrated that the lithium ion conduction in the perovskite-type manganese fluoride is attributed to counter cation-site vacancy mechanism. The divalent counter cation-doped KxBa(1-x)/2MnF3 was theoretically predicted as the lithium ion conductor in the perovskite-type manganese fluoride. In this study, we considered the oxygen doping for KxBa(1-x)/2MnF3 to realize the higher lithium ion conductivity. It is because lithium ion forms the stronger ionic bond with the doped oxygen anion. The hybrid-DFT calculations were performed to investigate the lithium ion conduction in the oxygen-doped KxBa(1-x)/2MnF3. The calculation results were discussed from the viewpoints of the potential energy curve, electron densities, and charge and spin densities. The effect of the lithium ion...

Energy Technology Data Exchange (ETDEWEB)

Electron paramagnetic resonance (EPR) of coals was considered by using iodine doping technique. Sub-bituminous coal (WA) and bituminous coal (UF) were used to observe EPR spectra using microwaves. With the UF coal, strength of the narrow component of the spectra was found constant regardless of amount of the doped iodine, wherein radicals without interaction with iodine were detected. Strength of the broad component increased with the iodine doping amount, where in deviation of {pi} electrons was detected, which have been generated as a result of interaction between aromatic rings and iodine in the coals. Spin concentration of the WA coal with low coalification degree is constant regardless of the iodine doping amount, and the interaction of the iodine with the aromatic rings was found small. The higher the coalification degree, the more the aromatic ring structure grows, and electron donor capability ...

Energy Technology Data Exchange (ETDEWEB)

TNF-doped Mylar is a new radiation-hard dielectric that has recently been qualified as a viable substitute for Mylar in capacitors. The advantage of TNF-doped Mylar is that it satisfies both the nuclear safety and radiation hardness requirements of weapons. Mylar is not radiation-hard. Aging and compatibility studies were carried out to insure that (1) TNF does not diffuse from the film during fabrication of the capacitor or during storage; and (2) there are no compatibility problems with aluminum foil (the conductor) or Fluorinert (the secondary dielectric). Losses of TNF were barely detectable during the vacuum bakes used in fabricating capacitors or during accelerated aging tests carried out below T{sub g} (70C) over a two year period in air. In other accelerated tests, no compatibility problems were detected with aluminum or Fluorinert. TNF-doped Mylar is now being used in the MC-4109 capacitor that was called out for ...

International Nuclear Information System (INIS)

Semiconductor properties of passive films formed on the Fe-18Cr alloy in a borate buffer solution (pH = 8.4) and 0.1 M H_2SO_4 solution were examined using a photoelectrochemical spectroscopy and an electrochemical impedance spectroscopy. Photo current reveals two photo action spectra that derived from outer hydroxide and inner oxide layers. A typical n-type semiconductor behaviour is observed by both photo current and impedance for the passive films formed in the borate buffer solution. On the other hand, a negative photo current generated, the absolute value of which decreased as applied potential increased in the sulfuric acid solution. This indicates that the passive film behaves as a p-type semiconductor. However, Mott-Schottky plot revealed the typical n-type semiconductor property. It is concluded that the passive film on the Fe-18Cr alloy formed in the borate buffer solution is composed of both n-type outer hydroxide and inner oxide layers. On the other ...

British Library Electronic Table of Contents (United Kingdom)

Summary Metabotropic GABAB receptors play a fundamental role in modulating the excitability of neurons and circuits throughout the brain. These receptors influence synaptic transmission by inhibiting presynaptic release or activating postsynaptic potassium channels. However, their ability to directly influence different types of postsynaptic glutamate receptors remains unresolved. Here we examine GABAB receptor modulation in layer 2/3 pyramidal neurons from the mouse prefrontal cortex. We use two-photon laser-scanning microscopy to study synaptic modulation at individual dendritic spines. Using two-photon optical quantal analysis, we first demonstrate robust presynaptic modulation of multivesicular release at single synapses. Using two-photon glutamate uncaging, we then reveal that GABAB r...

Science.gov (United States)

Molten zone recrystallized as well as sheet grown polycrystalline silicon has shown a minimum in the temperature dependence of the Hall mobility. In order to explain this experimental finding a new model is proposed, which is based on negatively charged grain boundaries for the p-type silicon material under study. This results in a potential well at the grain boundaries instead of the more generally observed potential barrier. A key feature in the model is that the space charge density at the grain boundary depends on the Fermi level position and therefore on temperature. In addition, the change in the measured Hall mobility before and after hydrogen passivation of the grain boundaries is discussed.

Energy Technology Data Exchange (ETDEWEB)

Four 10 MW, highly-stabilized power supply modules have been installed at the National High Magnetic Field Laboratory in Tallahassee, FL, to energize water-cooled, resistive, high-field research magnets. The power supply modules achieve a long term current stability if 10 ppM over a 12 h period with a short term ripple and noise variation of <10 ppM over a time period of one cycle. The power supply modules can operate independently, feeding four separate magnets, or two, three or four modules can operate in parallel. Each power supply module consists of a 12.5 kV vacuum circuit breaker, two three-winding, step-down transformers, a 24-pulse rectifier with interphase reactors, and a passive and an active filter. Two different transformer tap settings allow rated dc supply output voltages of 400 and 500 V. The rated current of a supply module is 17 kA and each ...

International Nuclear Information System (INIS)

In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C3H8O), water (H2O) and zinc acetate (Zn(CH3CO2)2) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(?) and reflectance R(?) spectra. Conjoint optical and thermal ...

International Nuclear Information System (INIS)

Full text of publication follows: Fission neutron irradiation to steels doped with isotope boron-10 is frequently conducted to study effects of the helium production on mechanical properties. The intrinsic mechanical properties of F82H steels could have been changed due to the boron doping. Recently, we reported that co-doping with boron and nitrogen to F82H (F82H+B+N) improved the mechanical properties of F82H doped only with boron. The mechanical properties of F82H+B+N are successfully comparable with the non-doped F82H before irradiation. In order to evaluate the effects of initial microstructure and helium production on radiation hardening, F82H and F82H+B+N were irradiate d Specimens used in this study were standard F82H martensitic steels, F82H steels doped with 60 mass ppm 10B and 200 ppm N (F82H+10B+N) and F82H steels doped with 60 ...

British Library Electronic Table of Contents (United Kingdom)

Fe-doped TiO2 hollow spheres (Fe-THs) were synthesized by sol?gel process using carbon spheres as templates. The prepared samples were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV?vis diffuse reflectance spectrum (DRS), N2 adsorption?desorption isotherms, Electron paramagnetic resonance (EPR) spectroscopy and Photoluminescence emission spectroscopy (PL). UV?vis spectra showed that Fe3+ doping could extend the absorption edge to the visible region. EPR spectra showed that Fe3+ was incorporated into the crystal lattice of TiO2, which could inhibit the recombination of photo-induced electron?hole pairs and improve the photocatalytic activity. The photocatalytic activities of the prepared samples were evaluated for the degradation of dye Reactive Brillia...

British Library Electronic Table of Contents (United Kingdom)

Antibacterial activity of Transition metals (Mn, Co) doped ZnO nanopowders prepared by a DC thermal plasma method against Escherichia coli and Staphylococcus aureus are investigated. The phase and morphology studies have been carried out by X-ray diffraction, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) respectively. All the samples of the present investigation are found to have hexagonal wurtzite structure and crystallite sizes are found to vary from 25nm to 30nm. Our bacteriological study showed the enhanced antibacterial activity of transition metals doped ZnO nanoparticles than undoped ZnO indicating the great potential of ZnO nanoparticles in relevant clinical and biomedical applications.

International Nuclear Information System (INIS)

The influence of hydrogen ion implantation into the channel polysilicon of polysilicon thin film transistors on gate oxide conductivity has been investigated. Data for effective tunnelling barriers at the gate oxide/channel polysilicon interface are presented. A value of 1.2eV for samples with boron doped channel polysilicon is calculated. For hydrogenated boron doped samples tunnelling barriers higher than 2.1 eV are obtained. The tunnelling barriers for phosphorus doped samples are impurity concentration dependent and decrease with increasing phosphorus concentration in the range 3 x 10"1"7 to 3 x 10"1"9 cm"-"3. (Author).

International Nuclear Information System (INIS)

LaPO4 single crystals lightly doped with Er3+, and codoped with Er3+ and Yb3+ have been grown by spontaneous nucleation in a lead phosphate flux. Absorption and luminescence spectra have been measured in the visible and near-IR regions and the excited state dynamics has been studied upon pulsed laser excitation. The obtained results have allowed the evaluation of the effective emission cross-sections around 1.5 ?m, that have been found to be similar to important oxide laser crystals doped with Er3+. Efficient visible upconversion has been observed upon excitation at 980 nm in the codoped crystals. This behaviour is attributed to Yb3+-Er3+ energy transfer processes.

Energy Technology Data Exchange (ETDEWEB)

Equivalent circuit and electrical parameters for H-doped NH{sub 4}UO{sub 2}PO{sub 4}.3H{sub 2}O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).

British Library Electronic Table of Contents (United Kingdom)

The core-shell luminol-doped SiO2 nanoparticles were synthesized and immobilized on the surface of chitosan film coating graphite electrode by the self-assembled technique. Then, a novel electrogenerated chemiluminescence (ECL) sensor for pyrogallol was developed based on its ECL enhancing effect for the core-shell luminol-doped silica nanoparticles. The ECL analytical performances and the sensing mechanism of this ECL sensor for pyrogallol were investigated in detail. The corresponding results showed that: compared with the conventional ECL reaction procedures by luminol ECL reaction system, the electrochemical (EC) reaction of pyrogallol and its subsequent chemiluminescence (CL) reaction occurred in the different spatial region whilst offering a high efficiency to couple the EC with the ...

International Nuclear Information System (INIS)

In this work we present the electrical characterization of non self-aligned p-channel thin film transistors fabricated by using laser doping technique for source/drain contact formation and gate oxide deposited at room temperature by Electron Cyclotron Resonance Plasma Enhanced Chemical Vapour Deposition. These techniques are suitable for a very low temperature process for TFT fabrication. The output characteristics show a current increase at high drain voltage ('kink' effect) rather moderate, if compared to self aligned polysilicon TFTs, probably due to the gradual doping profile induced by laser doping process. After bias stress at low gate voltage and high drain voltage condition a strong reduction of kink current has been observed in the output characteristics at high drain voltage, whereas minor changes has been observed in the transfer characteristics. This behaviour is similar to what observed in n-channel Gate ...

British Library Electronic Table of Contents (United Kingdom)

We present experimental evidence for self-organization of nickel microparticles in silicon under certain thermodynamic conditions of nickel diffusion doping. The concentration and distribution of the microparticles in silicon are very uniform. Additional anneals lead to self-ordering of the impurity microparticles.

Energy Technology Data Exchange (ETDEWEB)

The Co-doped BaTiO{sub 3} nanosized powders and ceramics were prepared via the sol-gel process. The powders and ceramics were characterized by methods of XRD, SEM and TEM. The dielectric properties of the ceramics were also determined by these methods. The influence of sintering temperature, sintering time and Co concentration on the microstructure and dielectric properties was discussed. The results revealed that the powders were in nanometer scale (30-50 nm) and were mainly composed of cubic BaTiO{sub 3} phase and small amount of BaCO{sub 3}. After sintering, both the cubic BaTiO{sub 3} and BaCO{sub 3} were transformed into tetrahedron BaTiO{sub 3}. The sintering temperatures of the Co-doped BaTiO{sub 3} ceramics decreased (about 100 deg. C) and the Curie temperatures of the ceramics were then moved to lower temperature. In addition, the dielectric constant of the ceramics doping with Co was higher than that of the pure ...

Energy Technology Data Exchange (ETDEWEB)

Carbon supported catalysts can lose their activity over a period of time due to the sintering of the nanometer-sized catalyst particles. The sintering of metal clusters on carbon supports can occur due to the weak interaction between the metal and the support and also due to the corrosion of carbon, especially in fuel cell electrocatalysts. The sintering may be reduced by increasing the interaction between the metal and the support and also by increasing the corrosion resistance of carbon supports. In an effort to mitigate the growth of the nanoparticles, carbon-substituted boron defects were introduced in the carbon lattice. The interaction between the Pt nanoparticles on the pure and boron-doped carbon supports was examined using X-ray photoelectron spectroscopy (XPS). The results indicate that the interaction between the Pt nanoparticles and the boron-doped carbon support was slightly stronger than the interaction between the Pt ...

Energy Technology Data Exchange (ETDEWEB)

A study has been made of B transient enhanced diffusion (TED) in heavily P-doped Si using secondary ion mass spectroscopy (SIMS) and positron annihilation spectroscopy (PAS). The P-doped silicon was implanted with boron ions of 40 keV energy to a dose of 3 {times} 10{sup 14} cm{sup {minus}2}, and then annealed at temperatures ranging from 700--1,000 C in a N{sub 2} ambient for varying durations. As P doping concentration increased from 3 {times} 10{sup 19} to 1 {times} 10{sup 20} cm{sup {minus}3}, boron diffusivity and the immobile boron fraction decreased. The experimental results are inconsistent with the predictions of the Fermi-level model and suggest that the clustering between B atoms and Si interstitials should be invoked in order to explain the immobile portion of the B peak during TED.

Energy Technology Data Exchange (ETDEWEB)

What kind of hardware and software should be used to interface GPIB devices with the existing computer system. One idea was to use a commercially available Multibus card, BLC 8488 from National Semiconductor, whose on-board Z80 would manage the GPIB read/write functions and handshakes. With this card, one could make a hardware system which would consist of (1) CAMAC 080, (2) Multibus crate, (3) M. Shea's M68000, (4) M080, (5) BLC 8488 and (6) memory board. And the software considered for such a hardware package was GAS, which had been an established software package for communication between the ACNET computer system and smart CAMAC modules. However, a second idea was to put everything on a two-wide CAMAC module. The author pursued the second idea and came up with a two-wide CAMAC module called C488. The author describes the hardware - block diagrams, circuit blocks, front panel and hardware tests. He also refers ...

British Library Electronic Table of Contents (United Kingdom)

We propose and demonstrate experimentally a singlelongitudinal-mode (SLM) fiber double-ring laser using an Erbium-doped waveguide amplifier (EDWA), polarization controller (PC), and a fiber Fabry-Perot tunable filter (FFP-TF) into the ring cavity. In addition, the output power, side-mode suppression ratio (SMSR), and the stabilities of power and wavelength of the laser also are investigated. (Copyright 2007 by Astro Ltd., Published exclusively by WILEY-VCH Verlag GmbH & Co. KGaA)

International Nuclear Information System (INIS)

We investigated the electrical characteristics and the junction depth of ultra-shallow junctions formed by using the plasma-doping method. Compared with ultra-low energy boron-ion implantation at 500 eV, the junctions formed with the plasma-doping process exhibited shallow junction depths and low sheet resistances. The junction depths of the plasma-doped samples were 150 A and 330 A after annealing for 10 s at 900 .deg. C and 950 .deg. C, respectively. For the same junction depth, the sheet resistance of the B_2H_6 plasma-doped sample was an order of magnitude less than that of the 500-eV B-ion implanted sample. Cross-sectional transmission electron microscopy and deep level transient spectroscopy showed that the defects formed by the B_2H_6 plasma-doping process could be removed by annealing at 950 .deg. C for 10 s. The scaling of metal-oxide-semiconductor field-effect-transistor ...

Energy Technology Data Exchange (ETDEWEB)

A solar cell structure is produced by a method comprising baking the solar cell, containing a gridded top layer of cuprous sulfide formed on a base of cadmium sulfide, for 20 minutes to 10 hours, to produce a copper doped cds electrically insulating region in the cadmium sulfide base near the interface of the cuprous sulfide and the cadmium sulfide; removing the cuprous sulfide, and the copper doped cds insulating region not covered by the grid, to provide a bare cadmium sulfide areas; and then forming a cuprous sulfide layer on the exposed areas not covered by the grid.

Energy Technology Data Exchange (ETDEWEB)

Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The ...

Science.gov (United States)

We have demonstrated fluorescence resonance energy transfer (FRET) between lanthanide-ion doped oxide nanoparticles acting as donors and organic acceptor molecules (Cy5). Due to the long nanoparticle lifetime and the large Stokes shift between nanoparticle absorption and emission, unambiguous and precise FRET measurements can be performed despite the presence of large free acceptor oncentrations. We determined FRET efficiencies as a function of Cy5 concentration which are in very good agreement with a multiple acceptor-multiple donor calculation.

Energy Technology Data Exchange (ETDEWEB)

The General Purpose Light Source VME module is an integral part of every front-end micro in the NSLS control system. The board incorporates features such as a video character generator, clock signals, time-of-day clock, a VME bus interrupter and general-purpose digital inputs and outputs. This module serves as a valuable diagnostic and real-time display tool for the micro development as well as for the final operational systems. This paper describes the functions provided by the board for the NSLS micro control monitor software.

Energy Technology Data Exchange (ETDEWEB)

The expected interstellar antiproton spectrum arising from cosmic-ray interactions in the Galaxy is recalculated, and the modulation of both antiprotons and protons is calculated using a two-dimensional modulation model incorporating gradient and curvature drifts and a wavy current sheet as well as the usual diffusion, convection, and energy-loss effects. Significant differences in the antiproton/proton ratio for different solar magnetic field polarities are predicted as well as a 'low-energy' component for antiprotons below about 1 GeV. 28 refs.

UK PubMed Central (United Kingdom)

The in vivo photochemical activity of photosystem II was inferred from modulated chlorophyll fluorescence and photoacoustic measurements in intact leaves of several plant species (Lycopersicon...Full Text Available

Science.gov (United States)

Adipocyte lipid-binding protein (ALBP or aP2) is an intracellular fatty acid-binding protein that is

International Nuclear Information System (INIS)

... Union (INTAS), Brussels (Belgium) Science and Technology Center in Unkraine,

UK PubMed Central (United Kingdom)

The steroidal regulation of vertebrate neuroanatomy and neurophysiology includes a seemingly unending list of brain areas, cellular structures and behaviors modulated by these hormones. Estrogens,...Full Text Available

Science.gov (United States)

... modules 2 and 3, 45 ft from each end) in a ... The toe of the stone revetment was 2 ft out from the ... in parentheses are for the current meters in layout 2. ...

UK PubMed Central (United Kingdom)

Temperature is an important modulator of longevity and aging in both poikilotherms and homeotherm animals. In homeotherms, temperature homeostasis is regulated primarily in the preoptic area...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This Guideline provides a set of procedures for the measurement of organic contaminants and particles in producer gases from biomass gasifiers. The procedures are designed to cover different gasifier types (updraft or downdraft fixed bed or fluidised bed gasifiers), operating conditions (0 - 900C and 0.6-60 bars) and concentration ranges (1 mg/m{sub n}{sup 3} to 300 g/m{sub n}{sup 3}). The Guideline describes a modular sampling train, and a set of procedures, which include: planning and preparation of the sampling, sampling and post-sampling, analysis, calculations, error analysis and reporting. The modular sampling train consists of 4 modules. Module 1 is a preconditioning module for isokinetic sampling and gas cooling. Module 2 is a particle collection module including a heated filter. Module 3 is a tar collection module with a gas quench ...

Science.gov (United States)

was deemed adequate and a cooling system designed utilizing the Melcor CP2-15- 10B thermoelectric module. Wall temperature achieved with this system was - 36 ...

Energy Technology Data Exchange (ETDEWEB)

An important growth in the power of the photovoltaic systems connected to a grid has recently been observed. In spite of the advances in module technology, the problems in the system design increased, especially regarding the surface of the earth they occupy. In this work we propose a complete model for plant simulation with different wiring diagrams and under dynamic shading. Results obtained from simulations showed that the configuration with the lowest performance was that of only one serial-parallel group, whereas the highest efficiency corresponded to a design of groups of modules in parallel connected then in series. In general, a higher efficiency was obtained diminishing the quantity of modules in series and increasing their number in parallel. The simulation model proposed allows exploring different alternatives of wiring modules and finding the most efficient configurations for photovoltaic ...

Energy Technology Data Exchange (ETDEWEB)

Code coupling activities have so far focused on coupling the neutronics modules with the CFD module. An interface module for the CFD-ACE/DeCART coupling was established as an alternative to the original STAR-CD/DeCART interface. The interface module for DeCART/CFD-ACE was validated by single-pin model. The optimized CFD mesh was decided through the calculation of multi-pin model. It was important to consider turbulent mixing of subchannels for calculation of fuel temperature. For the parallel calculation, the optimized decompose process was necessary to reduce the calculation costs and setting of the iteration and convergence criterion for each code was important, too.

UK PubMed Central (United Kingdom)

The pleiotropic actions of neuromodulators on pre- and postsynaptic targets present challenges to disentangling the mechanisms underlying regulation of synaptic transmission. Within the striatum,...Full Text Available

CERN Document Server

Microbonding of the CMS Tracker Inner Barrel (TIB) and Tracker Inner Disks (TID) modules was shared among six different Italian Institutes. The organization devised and the infrastructure deployed to handle this task is illustrated. Microbonding specifications and procedures for the different types of TIB and TID modules are given. The tooling specially designed and developed for these types of modules is described. Experience of production is presented. Attained production rates are given. An analysis of the microbonding quality achieved is presented, based on bond strengths measured in sample bond pull tests as well as on rates of bonding failures. Italian Bonding Centers routinely performed well above minimum specifications and a very low global introduced failure rate, at the strip level, of only $\\sim$0.015 \\% is observed.

UK PubMed Central (United Kingdom)

The synapsin III gene, SYN3, which belongs to the family of synaptic vesicle-associated proteins, has been implicated in the modulation of neurotransmitter...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

X-ray irradiation-induced paramagnetic radicals in rare earth (Ln) ion-doped glaserite and Ln ion-doped langbeinite were studied by means of ESR technique, aiming at developing the highly sensitive sensor for an ESR dosimetry. The samples were prepared by two kinds of procedures as follows. In one process, the glaserite (K{sub 3}Na(SO{sub 4}){sub 2}) matrix or the langbeinite (K{sub 2}Mg{sub 2}(SO{sub 4}){sub 3}) matrix were synthesized by heating the mixture of K{sub 2}SO{sub 4} and Na{sub 2}SO{sub 4} or the mixture of K{sub 2}SO{sub 4} and MgSO{sub 4} at 1023 K for 1 hour in He flow. The matrices obtained were mixed well with a fixed amount of Ln{sub 2}(SO{sub 4}){sub 3} (Ln=La, Eu, Gd, Lu) powder and heated at 1023 K for 1 hour in He flow. In the other process, the homogeneous mixture of a fixed amount of K{sub 2}SO{sub 4}, Na{sub 2}SO{sub 4} and Ln{sub 2}(SO{sub 4}){sub 3} powders or a fixed amount of K{sub 2}SO{sub 4}, MgSO{sub 4} and ...

Science.gov (United States)

We report on the formation of current blocking regions by O2 plasma treatment to reduce current crowding at the active region above the p-type electrodes of GaN-based vertical light emitting diodes (LEDs). The forward voltage and reverse current (at -5 V) of the plasma-treated LEDs slightly increase with increasing aging time. The output power (at 350 mA) of the plasma-treated LEDs is enhanced by 26% as compared to that of reference LEDs and is comparable to that of LEDs with SiO2 current blocking layers. It is shown that the output power (at 700 mA) of the plasma-treated LEDs is degraded by less than 2% of the initial value after 500 h.

International Nuclear Information System (INIS)

The electronic structures of platinum group elements (Ru, Os, Rh, Ir, Pd, and Pt) silicides have been calculated. Ir_3Si_5 is a semiconductor with the direct gap of 1.14 eV. Among monosilicides, RuSi and OsSi with the FeSi-type structure are semiconductors with the gap values of 0.21 and 0.41 eV but RhSi, IrSi, PdSi, and PtSi with the MnP-type structure are metals. No semiconducting compounds can be found in other platinum group elements silicides other than known Ru_2Si_3, Os_2Si_3, and OsSi_2.

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer conferring improved protection.

UK PubMed Central (United Kingdom)

Metabotropic glutamate receptor 2/3 (mGluR2/3) agonists were shown previously to nonselectively decrease both cocaine- and food-maintained responding in rats. mGluR2 positive allosteric modulators (PAMs)...Full Text Available

CERN Document Server

We provide an analytic study of the dynamics of semiconductor lasers with injection (pump) of spin-polarized electrons, previously considered in the steady-state regime. Using complementary approaches of quasi-static and small signal analyses, we elucidate how the spin modulation in semiconductor lasers can improve performance, as compared to the conventional (spin-unpolarized) counterparts. We reveal that the spin-polarized injection can lead to an enhanced bandwidth and desirable switching properties of spin-lasers.

Energy Technology Data Exchange (ETDEWEB)

Computer simulations and experiments indicate that we can shape the infrared picosecond pulses of the Mark III FEL in amplitude, frequency, and phase. Strongly modulated fundamental and second harmonic pulses have been generated by operating the Mark III FEL in the regime of strong sideband growth. In this paper, we present the results of simulations and experiments for second harmonic generation with fundamental inputs from 2 to 3 {mu}m.

CERN Document Server

We determine the structure of the total homology groups of exotic Springer fibers as affine Weyl group representations. As applications, we provide single top/socle property of standard modules in the exotic Deligne-Langlands correspondence (except for root of unity case), an analogue of Verma's theorem, the coincidence of analytic/geometric gradings in the $C ^{\\infty}$-realization of anti-spherical modules of graded Hecke algebras of type $\\mathsf{BC}$ with unequal parameters, among others.

British Library Electronic Table of Contents (United Kingdom)

We study the influence of Sr substitutions on the structural counterpart of the MI transition of Formula Not Shown . When Sr content increases, the commensurate CDW modulation of pure Formula Not Shown is changed into an incommensurate short range modulation that we attribute to a charge ordering of the Formula Not Shown electrons. The same features are observed in S deficient samples.

UK PubMed Central (United Kingdom)

BackgroundTo compare two strategies of dynamic intensity modulated radiation therapy (dIMRT) with 3-dimensional conformal radiation therapy (3DCRT) in the setting of hypofractionated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The National Center for Photovoltaics sponsored the 17th Workshop on Crystalline Silicon Solar Cells & Modules: Materials and Processes, held in Vail, CO, August 5-8, 2007. This meeting provided a forum for an informal exchange of technical and scientific information between international researchers in the photovoltaic and relevant non-photovoltaic fields. The theme of this year's meeting was 'Expanding Technology for a Future Powered by Si Photovoltaics.'

Energy Technology Data Exchange (ETDEWEB)

KM3NeT is a future deep-sea research infrastructure hosting a neutrino telescope with a volume of at least one cubic kilometer to be constructed in the Mediterranean Sea. The experiment aims to detect high-energy cosmic neutrinos using a 3D array of optical modules to collect the Cherenkov light induced by charged particles in the water. Upward going muons and showers produced in neutrino interactions with the surrounding matter will allow the search and study of possible sources of extra-terrestrial neutrinos. The design of optical modules makes an important impact on the performance and cost of the KM3NeT project. Several different optical module configurations are under consideration; based on glass pressure spheres containing: a large (10 in.) hemispherical photomultiplier tube (with a multi-anode version as an option); 25-31 3 in. photomultiplier tubes, or a crystal scintillator-based hybrid device (X-HPD). The ...

Energy Technology Data Exchange (ETDEWEB)

We summarize the results of point-contact Andreev-reflection (PCAR) spectroscopy in MgB{sub 2} doped by chemical substitutions, either magnetic (Mn) or non-magnetic (Al,C), obtained by us and by other groups in the last four years. Despite the variety of samples used (crystals and polycrystals of various origin) and some minor differences in the experimental techniques, these measurements have directly provided a complete and consistent picture of the effects of chemical substitutions on the gaps of MgB{sub 2} shedding light on other relevant parameters (scattering rates, DOSs) affected by doping. In Al-doped crystals and polycrystals, the gap amplitudes {delta}{sub {sigma}} and {delta}{sub {pi}} - obtained through a two-band Blonder-Tinkham-Klapwijk (BTK) fit of the Andreev-reflection conductance curves - decrease on increasing the Al content x (i.e. on decreasing the critical temperature of the contacts T{sub c}{sup A}), ...

Energy Technology Data Exchange (ETDEWEB)

Doping of molecular organic materials is important for the functionality of organic electronic devices as e.g solar cells. We investigated the doping behaviour of the acceptor molecules Cl{sub 2}-DCNQI and F{sub 16}CuPc incorporated into a CuPc matrix. In-situ XPS/UPS measurements were performed on coevaporated films. Doping by Cl{sub 2}-DCNQI was not successful. The molecule lost its chlorine atoms during thermal evaporation. For pristine F{sub 16}CuPc layers we observe a strong broadening of the photoemission features with increasing deposition rate indicating different domains probably of different molecular structure of differing electric interface potential. F{sub 16}CuPc incorporated into CuPc shows sharp photoemission features. With increasing F{sub 16}CuPc content Fermi level shifts are observed in both phases. In CuPc the maximum shift is about 0.45 eV towards the HOMO level indicating ...

International Nuclear Information System (INIS)

Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses were prepared in this study. The luminescence properties of the glasses were analyzed. A combination of blue, green, yellow, and red emission bands was shown for these glasses, and white light emission could be observed under UV light excitation. White light luminescence color could be changed by varying the excitation wavelength. Concentration quenching effect was investigated in this paper. Furthermore, the dependence of luminescence properties on glass compositions was studied. Results showed that the luminescence intensity changed with different network modifier oxides, while the white color luminescence was not affected significantly. - Graphical abstract: Tm3+ and Dy3+ ions co-doped aluminoborosilicate glasses, which emit white light under UV light excitation, were prepared. The dependence of luminescence properties on glass compositions was studied, and results showed that the white ...

International Nuclear Information System (INIS)

Delta-doped boron marker layers in silicon have been used to test further the relationship between B transient enhanced diffusion (TED) and the flux of silicon interstitials released during the annealing stage following self implantation. The authors present new data which address a number of questions raised by the present models. They show that in the experiments bulk trapping of interstitials is significant only for low implant fluences (#approx#10"1"2 cm"-"2). The origin of the observed diffusion-like profiles for the interstitial flux is instead found to lie in local trapping within the #delta#-doped layers themselves. Boron trapped in immobile clusters may be associated with Si interstitials in approximately a 1:1 ratio; nevertheless this trapping contribution alone may not entirely account for the observed gradient. They suggest that some part of the observed TED response with depth is attributable to local trapping of silicon ...

Energy Technology Data Exchange (ETDEWEB)

Praseodymium-doped Bi{sub 4}Ti{sub 3}O{sub 12} (BIT) with various compositions of dopant, Pr (x = 0.5, 0.6, 0.7, 0.8) in Bi{sub 4-x}Pr{sub x}Ti{sub 3}O{sub 12} (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800 deg. C exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x = 0.5) resulted in dramatically reduced of grain size from 2 {mu}m to less than 50 nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1 {mu}m was observed for x = 0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the addition of x = 0.50, and increasing with further addition of Pr. Dissipation factor (tan {delta}) ...

British Library Electronic Table of Contents (United Kingdom)

Praseodymium-doped Bi4Ti3O12 (BIT) with various compositions of dopant, Pr (x=0.5, 0.6, 0.7, 0.8) in Bi4-xPrxTi3O12 (BPT) were synthesized using a low temperature wet chemical technique. Powders calcined at 800degreeC exhibit a single phase polycrystalline perovskite bismuth-layered structure. Randomly oriented plate-like structures were observed under Scanning Electron Microscope (SEM). A small amount of Pr doping (x=0.5) resulted in dramatically reduced of grain size from 2mm to less than 50nm in which Pr plays the role as a grain growth inhibitor. However, by increasing the composition of Pr, bigger grain size of up to 1mm was observed for x=0.8 that was caused by diffusion of Pr in the perovskite structure. Dielectric properties showed that dielectric permittivity decreased with the ad...

Energy Technology Data Exchange (ETDEWEB)

By using this doping method, silicon semiconductors with extremely uniform dopant distributions can be produced, and this is the dominant advantage of NTD compared with a conventional chemical doping. Good uniformity of a dopant concentration is usually required for high power applications such as thyristor (SCR), IGBT, IGCT and GTO and for special sensors. Achieving an accurate neutron fluence corresponding to a target resistivity as well as a uniform irradiation is the prime target of a neutron irradiation for NTD. Generally, in order to reach an accurate neutron fluence, a real time neutron flux is monitored by a neutron detector such as a Self-powered Neutron Detector(SPND). And, after an irradiation, the total irradiation fluence is confirmed by measuring the absolute activity of a neutron activation sample that has been irradiated with a silicon ingot, and thus the SPND can be properly calibrated. Excellent irradiation uniformity and a ...

Energy Technology Data Exchange (ETDEWEB)

Carbons derived from the phase separation of polyacrylonitrile/solvent mixtures were investigated as lithium intercalation anodes for rechargeable lithium-ion batteries. The carbon electrodes have a bulk density of 0.35-0.5 g/cm{sup 3}, relatively low surface areas (< 10 m{sup 2}/g), and micron-size cells. Pyrolysis temperature influences the reversible lithium intercalation and the irreversible capacity (associated with the formation of the passivating layer). Carbon electrodes pyrolyzed at 600{degrees}C have first-cycle capacity as high as 550 mAh/g as well as large irreversible capacity, 440 mAh/g. Electrodes prepared at 1050{degrees}C have reversible capacities around 270 mAh/g with relatively lower capacity losses (120 mAh/g). Doping the organic precursors with phosphoric acid, prior to pyrolysis at 1050{degrees}C, leads to carbon electrodes with reversible capacities as high as 450 mAh/g. The capacity of doped carbon increased with ...

Energy Technology Data Exchange (ETDEWEB)

A p[sup +]-Al[sub 0.3]Ga[sub 0.7]As/n[sup +]-GaAs heterojunction tunnel diode was fabricated using Atomic Layer Epitaxy (ALE) growth technique. Background carbon doping of [similar to]10[sup 20] cm[sup [minus]3] was achieved in the p-side of the diode by optimizing growth conditions such as V/III ratio, exposure times to reactant gases, and growth temperature. In the n-side of the diode GaAs was doped with silane and doping concentrations as high as 7[times]10[sup 18] cm[sup [minus]3] were also achieved. The dopants are chosen to satisfy the high levels and low diffusion requirements. The diode can be used to interconnect the high and low band-gap cells in the AlGaAs/GaAs cascade solar cell structure. The reactor used in this investigation is a commercial MOCVD system which has been specially modified for dual operation of ALE and MOCVD growth modes.

International Nuclear Information System (INIS)

The intensity of erbium up-conversion luminescence could be limited by a saturation effect due to increased pump power. We studied the luminescence saturation of the 550 nm emission on erbium-doped, SiO_2-TiO_2 sol-gel powders under pulsed excitation at 979 and 1532 nm. From the latter, the up-converted luminescence intensity decreased with increasing excitation power, whereas no saturation was observed at 979 nm excitation. We proposed that the saturation effect is determined by the pump power, the erbium content and the lifetime of the corresponding first excited states at different pumping schemes.

British Library Electronic Table of Contents (United Kingdom)

Direct visualization of rare earths in @a- and @b-SiAlON unit-cells is performed through Z-contrast imaging technique in an aberration-corrected scanning transmission electron microscope. The preferential occupation of Yb and Ce atoms in different interstitial locations of @b-SiAlON lattice is demonstrated, yielding higher solubility for Yb than Ce. The triangular-like host sites in @a-SiAlON unit cell accommodate more Ce atoms than hexagonal sites in @b-SiAlON. We think that our results will be applicable as guidelines for many kinds of rare-earth-doped materials.

International Nuclear Information System (INIS)

This paper presents results of studying the thermo-transferred thermoluminescence (TTTl) phenomenon in potassium-yttrium double fluoride doped with terbium (K_2YF_5_:Tb) at different impurity concentrations (0.8%, 0.95% and 0.99%). Previously to study the TTTl phenomenon, structural characterization and chemical composition of the materials were determined. The structural studies were conducted using a scanning electron microscope; meanwhile, chemical composition was analyzed using energy dispersive X-ray spectroscopy. Thermoluminescence kinetics was studied irradiating the samples with "1"3"7Cs gamma rays as well as with "9"0Sr/"9"0Y beta rays, analyzing the glow curves by the deconvolution method for obtaining the kinetic parameters. (Author)

Science.gov (United States)

Cadmium telluride single crystals were grown heavily doped with chloride by the THM method. The resulting crystals were n-type with free carrier concentrations of the order of 10('12)/cm at room temperature. Hall effect studies revealed room temperature mobilities between 30 and 350 cm('2)/v-sec and resistivites between 2 x 10('3) and 10('4) ohm-cm. Studies were made of the gamma and alpha counting characteristics of these crystals with metal, metal-semiconductor, and metal-insulator electrodes. It was found that the MIS and MSS structures resulted in significant improvement over the MS structures in counting, signal-to-noise and energy resolution.

International Nuclear Information System (INIS)

The importance of point defects in semiconductor and function materials has been studied in detail, but effective means for detecting point defects has not been available for a long time. The end of range defects in Si, produced by 140 keV Ge"+ implantation, were investigated as detectors for measuring the interstitial concentration created by 42 keV B"+ implantation. The concentration of interstitial resulting from the B"+ implantation and the behavior of the interstitial flux under different annealing condition were given. The enhanced diffusion in the boron doped EPI marker, resulting from mobile non-equilibrium interstitials was demonstrated to be transient. Interstitial fluxes arising from processing can be detected by transient enhanced diffusion (TED) of doped marker layers as well

International Nuclear Information System (INIS)

The optical spectroscopy measurements of gadolinium gallium garnet (GGG) crystals doped with Yb show evidence of the presence of non-equivalent optical centers with very similar radiative decay rates. The energy level schemes of those centers have been determined on the basis of optical absorption, luminescence and Raman experiments. Crystal field fitting resulted in two sets of slightly different crystal field parameters for two non-equivalent Yb centers. Both sets of parameters describe perfectly the experimentally detected Y b3+ energy levels. Correlation between systematic trends in the experimental energy level schemes and crystal field parameters is discussed.

Energy Technology Data Exchange (ETDEWEB)

The spectroscopic properties of Pr{sup 3+} doping two lanthanum chlorotungstate hosts: the orthorhombic LaWO4Cl (1-1) and the hexagonal La3WO4Cl6 (3-1), as well as those of PrWO4Cl and Pr3wO613 have been investigated. The simulations of the energy level schemes are carried out within the crystal field theory frame. Each simulation involves 7 free ion parameters and 14 non-zero crystal field parameters (cfps), corresponding to the C{sub s} point symmetry of the site occupied by the rare earth, in both structures.

Energy Technology Data Exchange (ETDEWEB)

The spectroscopic properties of Cr{sup 2+}, Co{sup 2+}, and Ni{sup 2+}-doped single crystals of ZnS, ZnSe, and ZnTe have been investigated to understand their potential application as mid-IR tunable solid-state laser media. The spectroscopy indicated divalent Cr was the most favorable candidate for efficient room temperature lasing, and accordingly, a laser-pumped laser demonstration of Cr:ZnS and Cr:ZnSe has been performed. The lasers` output were peaked at {approximately} 2.35 {mu}m and the highest measured slope efficiencies were {approximately} 20% in both cases.

Energy Technology Data Exchange (ETDEWEB)

A previous note reviewed methods for the paramagnetic doping of materials for spin-polarized solid targets and some of the history of attempts to apply those methods to hydrocarbons. Since the earlier work on hydrocarbons had yielded, at best, rather mediocre results, that note also speculated on some ways to extend and, possibly, to improve upon the earlier work. The sharpest focus was on the light (number of carbons less than six) alkanes, since these are the hydrocarbons that have the highest hydrogen contents ([approx gt] 17wt %) and therefore require the least degree of polarization to be interesting. This present note summarizes the subsequent work done, to date, exploring some of the issues related to the chemical doping method. The main areas of progress have been in the literature search, experimental results on glass formation by alkanes, and a polarizing test of a prototype'' hydrocarbon.

British Library Electronic Table of Contents (United Kingdom)

Dopant-free Bi2Ti2O7 thin films with pyrochlore structure and La-doped bismuth titanate thin films have been fabricated by means of chemical solution decomposition, and characterized by X-ray diffraction, atomic force microscopy, scanning electron microscopy and UV?Vis spectrophotometry in this study. Their photocatalytic activities have been evaluated by photodegrading methyl orange solution, and the optimum processing parameters for the highest photocatalytic activity have been found. Moreover, the effects of La-doping on the phase transformation and the photocalalytic activity have been studied. It has been deduced from the experiment result that substituted La3+ ions can act as a stabilizer of Aurivillus phase BLT and a grain?growth inhibitor in BLT thin films.

International Nuclear Information System (INIS)

Silica glasses containing Pr"3"+ with and without CdS nanoparticles were prepared by sol-gel technique. The influence of CdS nanoparticles on Pr"3"+ doped glass was studied by absorption, photoluminescence and up-conversion. From the measured intensities of various absorption bands of these glasses, the Judd-Ofelt parameters ?_2, ?_4 and ?_6 have been evaluated. The radiative transition probability (A), radiative lifetime (?_R), branching ratio (?_R) and integrated emission cross-section (?_P) were calculated from excited states of "3P_1 and "3P_0 levels. The up-conversion emissions were found in the green, orange and red regions under 800 nm excitation with peaks 559, 612 and 688 nm respectively. On excitation with 370 nm also leads to similar green, orange and red regions.

CERN Document Server

Effect of a planar texture quality and its thickness on lasing spectrums and thresholds in dye-doped cholesteric liquid crystal (CLC) of steroid type is explored. Transition from the qualitative planar texture to the poor texture quality is accompanied by change of characteristic mode structures and by shift of barycentre in the long-wave side and the considerable growth of the lasing threshold. It is found that in the CLC texture created by substrates with perpendicular directions of orientation the stable single-mode lasing takes place. The nature of oscillated modes in such texture is caused by phase jump. The gained results show that in steroid CLC, unlike induced one, lasing spectrums is possible to feature with the coupled wave model. Key words: steroidal cholesteric liquid crystal, distributed feedback lasing, oscillation thresholds, phase defect of periodical structure, transmission and lasing spectra

Energy Technology Data Exchange (ETDEWEB)

We described the use of silica nanoparticles as building blocks for the immobilization of electrogenerated chemiluminescence (ECL) reagent Ru(bpy){sub 3}{sup 2+} and the fabrication of layer-by-layer assembly film by alternating the deposition of the Ru(bpy){sub 3}{sup 2+}-doped silica nanoparticles and Au nanoparticles. UV-vis absorption spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry and ECL were used to characterize the uniform growth of the multilayer film. Since Ru(bpy){sub 3}{sup 2+} could still maintain its ECL property when doped into the silica nanoparticles, the as-prepared multilayer film could be used as an effective ECL sensor, and the sensor showed high sensitivity and good stability.

British Library Electronic Table of Contents (United Kingdom)

We described the use of silica nanoparticles as building blocks for the immobilization of electrogenerated chemiluminescence (ECL) reagent Ru(bpy)32+ and the fabrication of layer-by-layer assembly film by alternating the deposition of the Ru(bpy)32+-doped silica nanoparticles and Au nanoparticles. UV-vis absorption spectroscopy, scanning electron microscopy (SEM), cyclic voltammetry and ECL were used to characterize the uniform growth of the multilayer film. Since Ru(bpy)32+ could still maintain its ECL property when doped into the silica nanoparticles, the as-prepared multilayer film could be used as an effective ECL sensor, and the sensor showed high sensitivity and good stability.

Energy Technology Data Exchange (ETDEWEB)

Internal friction of amorphous Pd/sub 80/Si/sub 20/ metal doped with hydrogen or deuterium was measured with a specially designed apparatus using amorphous metal sheet as a part of the electric oscillating circuit. Two peaks in Q/sup -1/ curve are observed. Applying the peak shift method to the first Snoek-like peak, we can determine the relaxation time from which the microdiffusion coefficient can be calculated. The obtained microdiffusion coefficient is about 10/sup -14/ m/sup 2//s at 200 K, being comparable with the macrodiffusion coefficient obtained from the releasing method. It can, however, not elucidate the hydrogen isotopic effect on the peak temperature of Q/sup -1/ curve, the activation energy for relaxation and the relaxation time from the present work because of the broadness of obtained Q/sup -1/ curve.

British Library Electronic Table of Contents (United Kingdom)

This paper presents the corrosion inhibition performance of soluble self-doped copolymers of aniline and 4-amino-3-hydroxy-naphthalene-1-sulfonic acid synthesized by chemical oxidative polymerization method. The corrosion inhibition behaviour of the copolymers in 1.0M HCl has been evaluated using Tafel Extrapolation method and electrochemical impedance spectroscopy (EIS) which was also used to propose the mechanism besides surface morphology. The results showed that the copolymer film exhibited the significant shifting in the corrosion potential and greater charge transfer resistance. The corrosion inhibition efficiency was found to increase from 50% to 90% by increasing the concentration of copolymer from 10 to 70mg/l in HCl medium. Moreover, the copolymer showed the larger degree of surf...

International Nuclear Information System (INIS)

A stable chlorobenzene dispersion of conducting polyaniline (PANI) has been obtained by doping emeraldine base with dodecylbenzene sulfonic acid (DBSA) and studied by spectrophotometric measurements in the UV-vis-IR range. The electrical properties of PANI: DBSA films obtained from the above dispersion have been investigated under different temperature and relative humidity conditions. All-organic chemoresistive devices have been developed by spin-coating the PANI: DBSA dispersion on flexible substrates, and then by depositing electrodes on the top, from a carbon nanotube conducting ink. Sensing tests performed under exposition to calibrated amounts of ammonia reveal that these simple and inexpensive sensors are able to detect ammonia at room temperature in a reliable way, with a sensitivity linearly related to concentration in the range between 5 ppm and 70 ppm.

British Library Electronic Table of Contents (United Kingdom)

A electrogenerated chemiluminescence (ECL) sensor for itopride was developed based on tris(2,2-bipyridyl)ruthenium(II) (Ru(bpy)32+)-doped silica (RuDS) nanoparticles/biopolymer chitosan composites membrane modified glassy carbon electrode (GCE). The RuDS nanoparticles (52+-5nm) were prepared by a modified Stber synthesis method and were characterized by electrochemical, fluorometric and transmission electron microscopy technology. The Ru(bpy)32+ encapsulation interior of the silica nanoparticle maintains its electrochemical activities and also reduces Ru(bpy)32+ leaching from the silica matrix when immersed in water due to the electrostatic interaction. The ECL analytical performances of this ECL sensor for itopride based on its enhancement ECL emission of Ru(bpy)32+ were investigated in d...

Energy Technology Data Exchange (ETDEWEB)

We have developed a low-temperature particle detector that uses a novel quasiparticle trapping mechanism to funnel athermal phonon energy from an 80 mg Ge absorber into a 1.6 mg doped Ge thermistor via a superconducting Al film. We report on pulse height spectra obtained at 320 mK by scanning a {sup 241}Am alpha source along the device, and show that up to 20% of the energy deposited in the Ge absorber by a 5.5 MeV alpha particle interaction can be collected into a thermistor via quasiparticle trapping. We show that this device is sensitive to the position of an alpha particle interaction in the Ge absorber for interaction distances of up to 5 mm from a quasiparticle trap.

Science.gov (United States)

We have been piloting web-based multimedia learning modules (MLMs), developed by the Physics Education Research Group at the University of Illinois at Urbana Champaign (UIUC), as a "prelecture assignment" in several introductory physics courses at California State Polytechnic University at Pomona. In this study, we report the results from a controlled study utilizing modules on electricity and magnetism as a part of a blended hybrid-online course. We asked students in the experimental section to view the MLMs prior to attending the face-to-face class, and to make sure this would not result in additional instructional time, we reduced the weekly class time by one-third. We found that despite reduced class time, student-learning outcomes were not hindered; in fact, the implementation of the UIUC MLMs resulted in a positive effect on student performance on conceptual tests and classroom discussion questions. (Contains 4 figures and 1 table.)

British Library Electronic Table of Contents (United Kingdom)

The generalized demodulation time-frequency analysis is a novel signal processing method, which is particularly suitable for the processing of multi-component amplitude-modulated and frequency-modulated (AM-FM) signals as it can decompose a multi-component signal into a set of single-component signals whose instantaneous frequencies own physical meaning. While fault occurs in gear, the vibration signals measured from gearbox would exactly display AM-FM characteristics. Therefore, targeting the modulation feature of gear vibration signal in run-ups and run-downs, a fault diagnosis method in which generalized demodulation time-frequency analysis and envelope order spectrum technique are combined is put forward and applied to the transient analysis of gear vibration signal. Firstly the multi-...

Science.gov (United States)

A 100-bit slitlike aperture array spatial light modulator has been developed using 8.8/65/35 PLZT for a high-bit-density 1-D hologram memory. The most desirable characteristics, such as distortion-free diffraction-limited Fourier transform patterns and good uniformity of displayed bit patterns over 100 bits, have been realized. The lowest SNR was 86, and rise time and fall time have been 30 microsec and 8 microsec, respectively, at 190-V halfwave voltage. One-dimensional holographic storage experiments have been successfully performed using this PLZT spatial light modulator. PMID:20216813

International Nuclear Information System (INIS)

In the frame of the Primary Wall Module prototype manufacturing for ITER, a consistent R and D phase was conducted in order to identify the industrial allowable tolerances and manufacturing problems which would occur when joining pieces by HIPping process during the PW module manufacturing. The purpose of this development was to give as industrial as possible manufacturing routes for joining together large Stainless Steel or DS-Copper pieces with Stainless Steel tubes and for bonding Beryllium tiles onto a curved component surface. The study concerned surface preparations, allowable gaps and joint geometry, Beryllium tile geometry, Titanium interlayer thickness, etc. This R and D phase also allowed the development and validation of different ultrasonic inspection tools needed for plate-plate, tube-plate, edge to edge plate bonding.

British Library Electronic Table of Contents (United Kingdom)

I. S. Kirbis, P. Maxwell, M. S. Flear, K. Miller and M. Ibrahim External quality control for immunocytochemistry on cytology samples: a review of UK NEQAS ICC (cytology module) results Objective:- To date, external quality control for immunocytochemistry on cytology samples is provided only by the United Kingdom national external quality assessment service for immunocytochemistry and in situ hybridisation (UK NEQAS ICC & ISH). For the purpose of this study a retrospective analysis of a comprehensive collection of quality-related data regarding immunocytochemistry on cytology samples collected through this service was analysed. Methods:- The quality of immunocytochemical reactions, using on-line collected data, was analysed for the last 23 UK NEQAS ICC cytology module external quality asses...

Energy Technology Data Exchange (ETDEWEB)

We report progress in an effort to develop and demonstrate a refuelable zinc/air battery for fleet electric vehicle applications. A refuelable module consisting of twelve bipolar cells with internal flow system has been refueled at rates of nearly 4 cells per minute refueling time of 10 minutes for a 15 kW, 55 kWh battery. The module is refueled by entrainment of 0.5-mm particles in rapidly flowing electrolyte, which delivers the particles into hoppers above each cell in a parallel-flow hydraulic circuit. The concept of user-recovery is presented as an alternative to centralized service infrastructure during market entry.

UK PubMed Central (United Kingdom)

The effect of TP (triosephosphates:glyceraldehyde-3 phosphate, GAP, +dihydroxyacetone phosphate, DHAP) on respiration, phosphorylation and matrix ATP/ADP ratios of isolated oat mesophyll mitochondria...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundProcessing of multimodal information is a critical capacity of the human brain, with classic studies showing bimodal stimulation either facilitating or interfering in perceptual...Full Text Available

UK PubMed Central (United Kingdom)

For intensity modulated radiation treatment (IMRT) dose reconstruction, multileaf collimator (MLC) log files have been shown applicable for deriving delivered fluence maps. However, MLC log files are...Full Text Available

UK PubMed Central (United Kingdom)

OBJECTIVETo determine if ProL1, a member of the opiorphin family of genes, can modulate erectile physiology, as it encodes a peptide which acts as...Full Text Available

CERN Document Server

Two dimensional Fourier spectra of near-infrared images of galaxies provide a powerful diagnostic tool for the detection of spiral arm modulation in stellar disks. Spiral arm modulation may be understood in terms of interference patterns of outgoing and incoming density wave packets or modes. The brightness along a spiral arm will be increased where two wave crests meet and constructively interfere, but will be decreased where a wave crest and a wave trough destructively interfere. Spiral arm modulation has hitherto only been detected in grand design spirals (such as Messier 81). Spiral arm amplitude variations have the potential to become a powerful constraint for the study of galactic dynamics. We illustrate our method in two galaxies: NGC 4062 and NGC 5248. In both cases, we have detected trailing and leading m=2 waves with similar pitch angles. This suggests that the amplification mechanism is the WASER type II. In this ...

Energy Technology Data Exchange (ETDEWEB)

The Fermilab Linac Upgrade is planned to increase the energy of the H- linac from 200 to 400 MeV. This is intended to reduce the incoherent space-charge tuneshift at injection into the 8 GeV Booster which can limit either the brightness or the total intensity of the beam. The Linac Upgrade will be achieved by replacing the last four 201.25 MHz drift-tube tanks which accelerate the beam from 116 to 200 MeV, with seven 805 MHz side-coupled cavity modules operating at an average axial field of abut 7.5 MV/m. This will allow acceleration to 400 MeV in the existing Linac enclosure. Each accelerator module will be driven with a klystron-based rf power supply. A prototype rf modulator has been built and tested at Fermilab, and a prototype 12 MW klystron is being fabricated by Litton Electron Devices. Fabrication of production accelerator modules is in progress. 8 figs., 4 tabs.

UK PubMed Central (United Kingdom)

BackgroundVisual neurons respond essentially to luminance variations occurring within their receptive fields. In primary visual cortex, each neuron is a filter for stimulus features...Full Text Available

UK PubMed Central (United Kingdom)

Many growth factors and hormones modulate the reproductive status in mammals. Among these, insulin and insulin-like growth factor I (IGF-I) regulate the development of gonadal tissues. SH2-B has been...Full Text Available

UK PubMed Central (United Kingdom)

Assimilatory nitrate reductase activity (NRA) in crude spinach leaf (Spinacia oleracea) extracts undergoes rapid changes following fluctuations in photosynthesis brought about by changes...Full Text Available

UK PubMed Central (United Kingdom)

Computer-aided diagnosis of neural diseases from EEG signals (or other physiological signals that can be treated as time series, e.g., MEG) is an emerging field that has gained much attention in past...Full Text Available

Science.gov (United States)

Apr 26, 1996 ... StainlesssteelJenn-Air cooktop w/4 burners, $20. Sam,332-3168. Sale:Condo, Friendswood,3-2-2A,1411sq It,. 409-925-4862. ...

UK PubMed Central (United Kingdom)

BackgroundPolymorphisms in Epidermal Growth Factor Receptor (EGFR) gene may influence EGFR production and/or activity, thereby modulating susceptibility to lung...Full Text Available

UK PubMed Central (United Kingdom)

Women experience a decline in estrogen and androgen levels after natural or surgically induced menopause, effects that are associated with a loss of sexual desire and bone mineral density. Studies in...Full Text Available

UK PubMed Central (United Kingdom)

Motivation: The identification of gene regulatory modules is an important yet challenging problem in computational biology. While many computational methods have been proposed to identify...Full Text Available

UK PubMed Central (United Kingdom)

A number of studies have examined the functional roles of individual muscles during normal walking, but few studies have examined which are the primary muscles that respond to changes in external...Full Text Available

UK PubMed Central (United Kingdom)

AbstractIntrathymic expression of tissue-restricted antigens (TRAs) has been viewed as the key element in the induction of central tolerance and recently, a central role for the autoimmune...Full Text Available

UK PubMed Central (United Kingdom)

Studies have shown that the nervous system may adopt a control scheme in which synergistic muscle groups are controlled by common excitation patters, or modules, to simplify the coordination...Full Text Available

UK PubMed Central (United Kingdom)

Inducible gene expression appears to be an essential event that couples light to entrainment of the master mammalian circadian clock located in the suprachiasmatic nucleus (SCN) of the hypothalamus....Full Text Available

UK PubMed Central (United Kingdom)

Mammals possess multiple insulin-like growth factor (IGF) binding proteins (IGFBPs), and related proteins, that modulate the activity of insulin/IGF signalling (IIS), a conserved neuroendocrine signalling...Full Text Available

UK PubMed Central (United Kingdom)

Segments of the chick basilar papilla were isolated and maintained in culture medium. The sensory hair bundle of individual hair cells was observed with light microscopy and stimulated with a water...Full Text Available

UK PubMed Central (United Kingdom)

The murine γ-herpesvirus-68 (γHV68) establishes viral latency in dendritic cells (DCs). In the present study, we examined the specific consequences...Full Text Available

UK PubMed Central (United Kingdom)

Auxin autonomous growth of most crown gall tumor cells requires the expression of two auxin biosynthesizing genes (tms 1 and tms 2) from the T-DNA of Agrobacterium...Full Text Available

UK PubMed Central (United Kingdom)

Ethnopharmacological relevanceHLXL is a traditional Chinese medicine that has long been used in folk medicine for the treatment of chronic inflammatory diseases....Full Text Available

UK PubMed Central (United Kingdom)

Orientation and movement relies on both visual and vestibular information mapped in separate coordinate systems. Here, we examine how coordinate systems interact to guide eye movements of rabbits....Full Text Available

UK PubMed Central (United Kingdom)

Our increasing capabilities for quantitative hormone analysis and automated high resolution growth studies have allowed a reassessment of the classical Cholodny-Went hypothesis of gravitropism. According...Full Text Available

UK PubMed Central (United Kingdom)

γ-Aminobutyric acid (GABA)-ergic transmission is critical for normal cortical function and is likely abnormal in a variety of neuropsychiatric disorders. We tested the in...Full Text Available

UK PubMed Central (United Kingdom)

Tamoxifen (TAM) is a selective estrogen receptor modulator widely used in the prevention and treatment of breast cancer. A major mode of metabolism of the major active metabolites of TAM, 4-OH-TAM...Full Text Available

UK PubMed Central (United Kingdom)

The programming of cellular networks to achieve new biological functions depends on the development of genetic tools that link the presence of a molecular signal to gene-regulatory activity. Recently,...Full Text Available

UK PubMed Central (United Kingdom)

BackgroundNeuropathic pain (NP) is partially mediated by neuroinflammatory mechanisms, and also modulates local neurogenic inflammation. Dietary lipids, in particular the total amount...Full Text Available

UK PubMed Central (United Kingdom)

Purpose:To investigate the clinical usage of dose verification of Helical Tomotherapy plans by using 2D-array ion chambers, and to develop an efficient way to validate the dose delivered...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This paper describes the needs, reasoning, approaches, and technical details to establish a practical accelerated weathering test (AWT) protocol for indoor testing of the photothermal stability of encapsulation materials and encapsulated solar cells and minimodules.

UK PubMed Central (United Kingdom)

Caries is a multifactorial disease, and studies aiming to unravel the factors modulating its etiology must consider all known predisposing factors. One major factor is bacterial colonization,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

ATLAS is one of the four experiments which will take place at the LHC, the CERN future protons collider. This accelerator, which should start in 2007, will allow to continue the studies carried out by its predecessors, as the standard model Higgs boson and new physics searches. The very high luminosity -10 fb{sup -1} during the first three functioning years, then 100 fb{sup -1}- and the 14 TeV in the frame center will ease these studies. The Centre de Physique des Particules de Marseille took part in the ATLAS collaboration, taking in charge half of the End-cap electromagnetic calorimeter modules construction. The description of this sub-detector and the construction steps, in particular the electrical tests which allow the stacking validation, are presented in this document. These tests results, obtained for the live first production modules, are analysed. The pre-series module (module 0) performances, ...

UK PubMed Central (United Kingdom)

BackgroundSteroidogenic acute regulatory (StAR) protein related lipid transfer (START) domains are small globular modules that form a cavity where lipids and lipid hormones bind....Full Text Available

UK PubMed Central (United Kingdom)

Germ cell tumor development in humans has been proposed to be part of testicular dysgenesis syndrome (TDS), which manifests as undescended testes, sterility, hypospadias, and, in extreme cases,...Full Text Available

UK PubMed Central (United Kingdom)

Zinc modulates the activity of glutamic acid decarboxylase, the rate limiting enzyme in the synthesis of gamma-aminobutyric acid (GABA), which is a major inhibitory neurotransmitter. Low cerebrospinal...Full Text Available

Science.gov (United States)

A program was conducted to develop a pop-up artificial-foliage system compatible with the rural Maryland (summertime) background environment. The result of this Phase I effort was a self-expanding leaf module, a number of which are stored flat in a simple...