WorldWideScience

Sample records for oil extraction process

  1. Process for extracting oil shale

    Energy Technology Data Exchange (ETDEWEB)

    1920-08-22

    A process is described for recovering bituminous material from oil shale, characterized in that the oil shale is extracted with wood spirits oil (byproduct of woodspirit rectification), if necessary in admixture with other solvents in the cold or the hot.

  2. Comparative exergy analyses of Jatropha curcas oil extraction methods: Solvent and mechanical extraction processes

    International Nuclear Information System (INIS)

    Ofori-Boateng, Cynthia; Keat Teong, Lee; JitKang, Lim

    2012-01-01

    Highlights: ► Exergy analysis detects locations of resource degradation within a process. ► Solvent extraction is six times exergetically destructive than mechanical extraction. ► Mechanical extraction of jatropha oil is 95.93% exergetically efficient. ► Solvent extraction of jatropha oil is 79.35% exergetically efficient. ► Exergy analysis of oil extraction processes allow room for improvements. - Abstract: Vegetable oil extraction processes are found to be energy intensive. Thermodynamically, any energy intensive process is considered to degrade the most useful part of energy that is available to produce work. This study uses literature values to compare the efficiencies and degradation of the useful energy within Jatropha curcas oil during oil extraction taking into account solvent and mechanical extraction methods. According to this study, J. curcas seeds on processing into J. curcas oil is upgraded with mechanical extraction but degraded with solvent extraction processes. For mechanical extraction, the total internal exergy destroyed is 3006 MJ which is about six times less than that for solvent extraction (18,072 MJ) for 1 ton J. curcas oil produced. The pretreatment processes of the J. curcas seeds recorded a total internal exergy destructions of 5768 MJ accounting for 24% of the total internal exergy destroyed for solvent extraction processes and 66% for mechanical extraction. The exergetic efficiencies recorded are 79.35% and 95.93% for solvent and mechanical extraction processes of J. curcas oil respectively. Hence, mechanical oil extraction processes are exergetically efficient than solvent extraction processes. Possible improvement methods are also elaborated in this study.

  3. Standard Operation Procedure of Gaharu Oil Extraction Process

    International Nuclear Information System (INIS)

    Peng, C.S.; Mohd Fajri Osman; Norella Bahari; Rusli Zakaria

    2015-01-01

    Gaharu oil extraction system developed by Nuclear Malaysia is a hydro-distillation system innovated from the tradition method and improvised with science and technology to enhance the process efficiency and safety. The main component of gaharu oil extraction system included the extraction vessel, condenser and collection decanter. Apart from the extraction unit, the gaharu oil extraction process also incorporated two major supporting systems. These systems are the liquefied petroleum gas (LPG) system and the water cooling system. The LPG system is solely used for heating the vessel, which contains a mixture of treated and grind gaharu bark and fluid, to produce steam. Meanwhile the water cooling system is used to supply the necessary cool water into the condenser unit and facilitate in the transformation of the mentioned steam into gaharu oil and distilled water. The dissipate water from this process will be channeled back into the water cooling ponds to let excess heat to be removed and allow the cool water to reuse again by the process. (author)

  4. Investigation on microbiology of olive oil extraction process

    Directory of Open Access Journals (Sweden)

    B. Zanoni

    2015-06-01

    Full Text Available Several batches of approx. 200 kg olives from Frantoio and Moraiolo cultivars were processed in an oil mill at two dates of harvesting. Samples were collected in several steps of extraction process for sensory, chemical and microbial analyses.All extracted olive oil from the second olive harvesting date was affected by sensory defects and hence classified as being “non-extra virgin”. A distinction between extra virgin olive oil and nonextra virgin olive oil obtained from both harvesting dates was explained by the volatile compounds content of olive oil samples and by yeast and mould counts collected at different processing steps.

  5. Supercritical Extraction Process of Allspice Essential Oil

    Directory of Open Access Journals (Sweden)

    Yasvet Y. Andrade-Avila

    2017-01-01

    Full Text Available Allspice essential oil was extracted with supercritical carbon dioxide (SC-CO2 in a static process at three different temperatures (308.15, 313.15, and 318.15 K and four levels of pressure (100, 200, 300, and 360 bar. The amount of oil extracted was measured at intervals of 1, 2, 3, 4, 5, and 6 h; the most extraction yield reached was of 68.47% at 318.15 K, 360 bar, and 6 h of contact time. In this supercritical extraction process, the distribution coefficient (KD, the mean effective diffusion coefficient (Def, the energy of activation (Ea, the thermodynamic properties (ΔG0, ΔH0, and ΔS0, and the apparent solubility (S expressed as mass fraction (w/w were evaluated for the first time. At the equilibrium the experimental apparent solubility data were successfully correlated with the modified Chrastil equation.

  6. Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

    Directory of Open Access Journals (Sweden)

    Giacomo Costagli

    2015-10-01

    Full Text Available Nowadays the avocado fruit (Persea americana Mill. is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or solvent extraction units cannot be installed. These traditional processes yield a grade of oil that needs subsequent refining and is mainly used in the cosmetic industry. In the late 1990s, in New Zeland, a processing company with the collaboration of Alfa Laval began producing cold-pressed avocado oil (CPAO to be sold as edible oil for salads and cooking. Over the last fifteen years, CPAO production has increased in many other countries and has led to an expansion of the market which is set to continue, given the growing interest in highquality and healthy food. Avocado oil like olive oil is extracted from the fruit pulp and in particular shares many principles of the extraction process with extra-vergin olive oil. We conducted a review of traditional and modern extraction methods with particular focus on extraction processes and technology for CPAO production.

  7. Multiclass pesticide determination in olives and their processing factors in olive oil: comparison of different olive oil extraction systems.

    Science.gov (United States)

    Amvrazi, Elpiniki G; Albanis, Triantafyllos A

    2008-07-23

    The processing factors (pesticide concentration found in olive oil/pesticide concentration found in olives) of azinphos methyl, chlorpyrifos, lambda-cyhalothrin, deltamethrin, diazinon, dimethoate, endosulfan, and fenthion were determined in olive oil production process in various laboratory-scale olive oil extractions based on three- or two-phase centrifugation systems in comparison with samples collected during olive oil extractions in conventional olive mills located at different olive oil production areas in Greece. Pesticide analyses were performed using a multiresidue method developed in our laboratory for the determination of different insecticides and herbicides in olive oil by solid-phase extraction techniques coupled to gas chromatography detection (electron capture detection and nitrogen phosphorus detection), optimized, and validated for olive fruits sample preparation. Processing factors were found to vary among the different pesticides studied. Water addition in the oil extraction procedure (as in a three-phase centrifugation system) was found to decrease the processing factors of dimethoate, alpha-endosulfan, diazinon, and chlorpyrifos, whereas those of fenthion, azinphos methyl, beta-endosulfan, lambda-cyhalothrin, and deltamethrin residues were not affected. The water content of olives processed was found to proportionally affect pesticide processing factors. Fenthion sulfoxide and endosulfan sulfate were the major metabolites of fenthion and endosulfan, respectively, that were detected in laboratory-produced olive oils, but only the concentration of fenthion sulfoxide was found to increase with the increase of water addition in the olive oil extraction process.

  8. Walnut and almond oil screw-press extraction at industrial scale: Effects of process parameters on oil yield and quality

    Directory of Open Access Journals (Sweden)

    M. L. Martínez

    2018-01-01

    Full Text Available Walnut and almond kernels are highly nutritious mainly due to their high oil contents. In this study, 32 factorial experimental designs were used to optimize processes for oil extraction by screw-pressing at industrial scale. Experimental designs included seed moisture content (SMC, and restriction die (RD as the main processing parameters. Theoretical models were scanned against experimental data in order to optimize oil extraction conditions. The response variables analyzed were oil yield (OY, fine solid content (FC in oil, and oil quality parameters. Fitted models for OY indicated maximum predicted values similar to the highest experimental values. Walnut oil extractions showed a maximum OY (84.5 ± 2.3 % at 7.21% SMC, and 10 mm RD. For almond kernels, maximum OY (71.9 ± 3.5% was obtained at 9.42% SMC, and 12 mm RD. Chemical quality parameters from both oils were in the ranges stated in Codex (FAO/WHO standards for virgin (non-refined oils.

  9. Walnut and almond oil screw-press extraction at industrial scale: Effects of process parameters on oil yield and quality

    International Nuclear Information System (INIS)

    Martínez, M. L.; Bordón, M.G.; Bodoira, R. M.; Penci, M.C.; Ribotta, P.D.; Maestri, D.M.

    2017-01-01

    Walnut and almond kernels are highly nutritious mainly due to their high oil contents. In this study, 32 factorial experimental designs were used to optimize processes for oil extraction by screw-pressing at industrial scale. Experimental designs included seed moisture content (SMC), and restriction die (RD) as the main processing parameters. Theoretical models were scanned against experimental data in order to optimize oil extraction conditions. The response variables analyzed were oil yield (OY), fine solid content (FC) in oil, and oil quality parameters. Fitted models for OY indicated maximum predicted values similar to the highest experimental values. Walnut oil extractions showed a maximum OY (84.5 ± 2.3 %) at 7.21% SMC, and 10 mm RD. For almond kernels, maximum OY (71.9 ± 3.5%) was obtained at 9.42% SMC, and 12 mm RD. Chemical quality parameters from both oils were in the ranges stated in Codex (FAO/WHO) standards for virgin (non-refined) oils. [es

  10. Influence of enzymes on the oil extraction processes in aqueous media

    Directory of Open Access Journals (Sweden)

    Ricochon Guillaume

    2010-11-01

    Full Text Available The methods of oil aqueous extraction process (AEP assisted by enzymes are, over the last 50 years, an alternative designed to replace traditional methods of extraction using organic solvents. To extract the oil using an AEP, the use of specific enzymes, able to hydrolyze some or all components of seeds, can significantly increase the yields of extraction. Hydrolyzing the different constituents of cell walls (cellulose, hemicellulose, pectins, proteins, etc., enzymes are able to enhance the liberation of the oil. A number of physico-chemical parameters must also be considered for the better expression of the enzymatic mixture, while maintaining the quality of oils and meals. This article presents the various factors influencing the release of oil in aqueous media and the main results obtained by this process on various substrates.

  11. Optimization of castor seed oil extraction process using response surface methodology

    Directory of Open Access Journals (Sweden)

    J. D. Mosquera-Artamonov

    2016-09-01

    Full Text Available This work focuses on the study of the oil extraction yield from castor seed using three different seed conditions: whole, minced and bare endosperm. Taguchi design was used to determine the contribution of the following parameters: seed condition, seed load in the extractor, temperature, and pressure. It was proved that it is necessary to introduce the whole seed and that the presence of the pericarp increases the extraction yield. The contribution of the control factors has an extraction yield limit. After determining which factors contributed to the process, these were left at their optimum levels aiming to reduce the control factors to only two. The complete analysis was done using a surface response methodology giving the best parameter for temperature and pressure that allows a better yielding mechanical extraction. The oil extraction yield can be kept up to 35% of the seed.

  12. Optimization of aqueous enzymatic extraction of oil from shrimp processing by-products using response surface methodology

    Directory of Open Access Journals (Sweden)

    Chen WENWEI

    2018-06-01

    Full Text Available Abstract The aqueous enzymatic extraction (AEE of oil from shrimp processing by-products was investigated. Four kinds of proteases, including alkaline protease, neutral protease, flavor protease and compound protease, were applied to hydrolysis shrimp processing by-products. The results showed that flavor protease was the best hydrolysis enzyme for shrimp processing by-products to obtain high oil recovery. The influences of four factors, including enzyme amount, liquid/solid ratio, hydrolysis time and hydrolysis temperature, on shrimp oil extraction yield were also studied. The flavor enzyme hydrolysis condition was optimized as following: enzyme amount of 2.0% (w/w, liquid/solid ratio of 9.0ml/g, hydrolysis time of 2.6 h and hydrolysis temperature of 50 °C. Under these optimum hydrolysis conditions, the experimental oil extraction yield was 88.9%.

  13. Process of extracting oil from stones and sands. [heating below cracking temperature and above boiling point of oil

    Energy Technology Data Exchange (ETDEWEB)

    Bergfeld, K

    1935-03-09

    A process of extracting oil from stones or sands bearing oils is characterized by the stones and sands being heated in a suitable furnace to a temperature below that of cracking and preferably slightly higher than the boiling-point of the oils. The oily vapors are removed from the treating chamber by means of flushing gas.

  14. Radionuclide concentrations in oil extraction and production processes in Northeast Brazil

    International Nuclear Information System (INIS)

    Gazineu, Maria Helena Paranhos

    2005-06-01

    Since the beginning of the twentieth century the presence of naturally occurring radioactive material (NORM) was detected in the water and oil extracted from wells both onshore and offshore. The oil is extracted together with water and sediments which contain radionuclides of the uranium and thorium series. Among the radionuclides present, especial attention should be given to 226 Ra and 228 Ra, due to its long half-life and importance, from the radiological point of view. The objective of this work was to identify the natural radionuclides in the oil industry, to determine their activity concentration, and from these results, to evaluate the risks the employees of the oil industry are exposed to. Samples of sludge, scale and produced water extracted with the oil were collected from three oil processing stations in the state of Sergipe, Brazil. The activity concentrations of the radionuclides were determined in the solid samples before and after the extraction of the oil. The chemical and mineralogical composition of the samples without oil was evaluated. Water samples, on the other hand, were analyzed for their contents of radionuclides and barium concentration. It was observed that the activity concentrations of the analyzed radionuclides ( 226 Ra, 228 Ra, 228 Th and 210 Pb) in sludge and scales were very high when compared with the literature, particularly much higher than the values for 226 Ra and 228 Ra obtained for sludge and scales from the oil platforms near the city of Campos, state of Rio de Janeiro. The maximum concentration values for 226 Ra, 228 Ra, 228 Th and 210 Pb (3,500, 2,195, 2,248.6 and 201 kBq kg -1 , respectively) were obtained for the scales after the extraction of the oil. The analysis of the samples showed that barium sulphate (barite) and strontium sulphate (celestite) are the main constituents of the scales, while carbonates and silicates, together with other compounds are the components of sludge. A correlation between barium, 226 Ra and

  15. Green bio-oil extraction for oil crops

    Science.gov (United States)

    Zainab, H.; Nurfatirah, N.; Norfaezah, A.; Othman, H.

    2016-06-01

    The move towards a green bio-oil extraction technique is highlighted in this paper. The commonly practised organic solvent oil extraction technique could be replaced with a modified microwave extraction. Jatropha seeds (Jatropha curcas) were used to extract bio-oil. Clean samples were heated in an oven at 110 ° C for 24 hours to remove moisture content and ground to obtain particle size smaller than 500μm. Extraction was carried out at different extraction times 15 min, 30 min, 45 min, 60 min and 120 min to determine oil yield. The biooil yield obtained from microwave assisted extraction system at 90 minutes was 36% while that from soxhlet extraction for 6 hours was 42%. Bio-oil extracted using the microwave assisted extraction (MAE) system could enhance yield of bio-oil compared to soxhlet extraction. The MAE extraction system is rapid using only water as solvent which is a nonhazardous, environment-friendly technique compared to soxhlet extraction (SE) method using hexane as solvent. Thus, this is a green technique of bio-oil extraction using only water as extractant. Bio-oil extraction from the pyrolysis of empty fruit bunch (EFB), a biomass waste from oil palm crop, was enhanced using a biocatalyst derived from seashell waste. Oil yield for non-catalytic extraction was 43.8% while addition of seashell based biocatalyst was 44.6%. Oil yield for non-catalytic extraction was 43.8% while with addition of seashell-based biocatalyst was 44.6%. The pH of bio-oil increased from 3.5 to 4.3. The viscosity of bio-oil obtained by catalytic means increased from 20.5 to 37.8 cP. A rapid and environment friendly extraction technique is preferable to enhance bio-oil yield. The microwave assisted approach is a green, rapid and environmental friendly extraction technique for the production of bio-oil bearing crops.

  16. Enumeration and rapid identification of yeasts during extraction processes of extra virgin olive oil in Tuscany.

    Science.gov (United States)

    Mari, Eleonora; Guerrini, Simona; Granchi, Lisa; Vincenzini, Massimo

    2016-06-01

    The aim of this study was to evaluate the occurrence of yeast populations during different olive oil extraction processes, carried out in three consecutive years in Tuscany (Italy), by analysing crushed pastes, kneaded pastes, oil from decanter and pomaces. The results showed yeast concentrations ranging between 10(3) and 10(5) CFU/g or per mL. Seventeen dominant yeast species were identified by random amplified polymorphic DNA with primer M13 and their identification was confirmed by restriction fragments length polymorphism of ribosomal internal transcribed spacer and sequencing rRNA genes. The isolation frequencies of each species in the collected samples pointed out that the occurrence of the various yeast species in olive oil extraction process was dependent not only on the yeasts contaminating the olives but also on the yeasts colonizing the plant for oil extraction. In fact, eleven dominant yeast species were detected from the washed olives, but only three of them were also found in oil samples at significant isolation frequency. On the contrary, the most abundant species in oil samples, Yamadazyma terventina, did not occur in washed olive samples. These findings suggest a phenomenon of contamination of the plant for oil extraction that selects some yeast species that could affect the quality of olive oil.

  17. Extraction and Characterization of Cottonseed (Gossypium) Oil

    OpenAIRE

    Efomah Andrew Ndudi; Orhevba Bosede Adelola

    2012-01-01

    This study investigated the extraction and characterization of cottonseed oil using solvent extraction method. Normal hexane was used as solvent in the extraction process. The AOAC method of Analysis was employed in the determination of the chemical, physical and proximate compositions of the oil. The chemical properties of the oil determined include the saponification value, free fatty acid, iodine value, peroxide value and acid value. The physical properties of the oil determined are viscos...

  18. The extraction of bitumen from western oil sands

    International Nuclear Information System (INIS)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-08-01

    The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report

  19. Supercritical CO2 extraction of candlenut oil: process optimization using Taguchi orthogonal array and physicochemical properties of the oil.

    Science.gov (United States)

    Subroto, Erna; Widjojokusumo, Edward; Veriansyah, Bambang; Tjandrawinata, Raymond R

    2017-04-01

    A series of experiments was conducted to determine optimum conditions for supercritical carbon dioxide extraction of candlenut oil. A Taguchi experimental design with L 9 orthogonal array (four factors in three levels) was employed to evaluate the effects of pressure of 25-35 MPa, temperature of 40-60 °C, CO 2 flow rate of 10-20 g/min and particle size of 0.3-0.8 mm on oil solubility. The obtained results showed that increase in particle size, pressure and temperature improved the oil solubility. The supercritical carbon dioxide extraction at optimized parameters resulted in oil yield extraction of 61.4% at solubility of 9.6 g oil/kg CO 2 . The obtained candlenut oil from supercritical carbon dioxide extraction has better oil quality than oil which was extracted by Soxhlet extraction using n-hexane. The oil contains high unsaturated oil (linoleic acid and linolenic acid), which have many beneficial effects on human health.

  20. Process optimization and characterization of fragrant oil from red pepper (Capsicum annuum L.) seed extracted by subcritical butane extraction.

    Science.gov (United States)

    Gu, Ling-Biao; Pang, Hui-Li; Lu, Ke-Ke; Liu, Hua-Min; Wang, Xue-De; Qin, Guang-Yong

    2017-04-01

    Red pepper seeds account for 450-500 g kg -1 of the total pepper weight and are often discarded as waste. In this study, process optimization and characterization of fragrant oil from roasted red pepper seed extracted by subcritical butane extraction were carried out. The optimal conditions of extraction were a temperature of 74.61 °C, a time of 68.65 min and a liquid/solid ratio of 30.24:1. The oil had a refractive index (25 °C) of 1.471, a relative density of 0.900, an acid value of 1.421 mg g -1 oil, an iodine value of 127.035 g per 100 g, a saponification value of 184.060 mg KOH g -1 , an unsaponifiable matter content of 12.400 g kg -1 , a peroxide value of 2.465 meq. O 2 kg -1 and a viscosity of 52.094 cP. The main fatty acids in the oil were linoleic acid (72.95%) followed by palmitic acid (11.43%) and oleic acid (10.00%). The oil showed desirable thermal and oxidative stability. A total of 19 volatile compounds, mostly aldehydes and alkenes, were identified from the oil. The results indicated that the method is appropriate for the preparation of fragrant red pepper seed oil, and the oil is suitable for used as edible oil. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  1. Delay oil oxidation during frying process

    International Nuclear Information System (INIS)

    Atta, N.M.M.; Shams Eldin, N.M.M.

    2010-01-01

    Blend oil (mixed of refined sunflower and soy beans oils 1:1 w/w) containing add 200 ppm of rosemary leaves methanolic extract (rosemary extract) (RE) and 3% refined rice bran oil (RRBO), were used in frying process at 1800 degree c for 5 hrs/ day, four consecutive days to delay oil oxidation during frying. Therefore, rosemary extract (methanolic extract) was analyzed by HPLC technique for identification of flavonoids compounds (as a specific active compounds; gives high protection to frying oil). Physical and chemical properties, including refractive index(RI). Red color unit (R), viscosity, acidity (FFA), peroxide value (PV), iodine value (IV) oxidized fatty acid (OFA), polymer content (PC), total polar components (TPC) and trans fatty acid (TFA) as eliadic acid were determined. The results indicated that; rosemary extract contained about eight flavonoids compounds (hypersoid, rutin, 3-OH flavon, luleotin, kempferol, sakarutin, querectrin and apeginin). Addition of RE or RRBO to frying oil caused delay oil oxidation during frying process compared with frying oil without any addition. Also, the results indicated that rosemary extract was more effective in reducing formation of PV, FFA, OFA, PC, TPC and TFA in frying oil than refined rice bran oil

  2. Extracting oils

    Energy Technology Data Exchange (ETDEWEB)

    Patart, G

    1926-03-15

    In the hydrogenation or extraction of by-products from organic substances at high temperatures and pressures, the gases or liquids, or both, used are those which are already heated and compressed during industrial operations such as exothermic synthesizing reactions such as the production of methanol from hydrogen and carbon monoxide in a catalytic process. Gases from this reaction may be passed upwardly through a digester packed with pine wood while liquid from the same catalytic process is passed downwardly through the material. The issuing liquid contains methanol, pine oil, acetone, isopropyl alcohol, and acetic acid. The gases contain additional hydrogen, carbon monoxide, methane, ethylene, and its homologs which are condensed upon the catalyser to liquid hydrocarbons. Petroleum oils and coal may be treated similarly.

  3. Effects of thermal processing on physicochemical properties and oxidative stability of Balanities aegyptiaca kernels and extracted oil

    International Nuclear Information System (INIS)

    Elbadawi, S.M.A.; Ahmad, E.E.M.; Mariod, A.A.; Mathäus, B.

    2017-01-01

    In the present study, the effects of roasting and boiling on the proximate composition of the kernels as well as the physicochemical properties and oxidative stabilities of the extracted oils of Balanites aegyptiaca were investigated. Roasting was performed at 180 °C for 15 minutes, whereas boiling of the kernels was carried out in tap water for one hour. The oils from raw and thermally processed samples were extracted using n-hexane in a Soxhlet extraction apparatus and characterized. The roasting significantly (p < 0.05) influenced the peroxide value and the oxidative stability of the extracted oil in a positive way; whereas boiling had the opposite effect. The oils were composed of linoleic, oleic, stearic, and palmitic acids as the major fatty acids (96%) and contained predominantly α- and γ-tocopherols (ca. 400mg/kg). The study suggests that the oil from roasted kernels could be used as a natural antioxidant for enhancing the characteristics of other edible oils via blending. [es

  4. Aqueous enzymatic extraction of Moringa oleifera oil.

    Science.gov (United States)

    Mat Yusoff, Masni; Gordon, Michael H; Ezeh, Onyinye; Niranjan, Keshavan

    2016-11-15

    This paper reports on the extraction of Moringa oleifera (MO) oil by using aqueous enzymatic extraction (AEE) method. The effect of different process parameters on the oil recovery was discovered by using statistical optimization, besides the effect of selected parameters on the formation of its oil-in-water cream emulsions. Within the pre-determined ranges, the use of pH 4.5, moisture/kernel ratio of 8:1 (w/w), and 300stroke/min shaking speed at 40°C for 1h incubation time resulted in highest oil recovery of approximately 70% (goil/g solvent-extracted oil). These optimized parameters also result in a very thin emulsion layer, indicating minute amount of emulsion formed. Zero oil recovery with thick emulsion were observed when the used aqueous phase was re-utilized for another AEE process. The findings suggest that the critical selection of AEE parameters is key to high oil recovery with minimum emulsion formation thereby lowering the load on the de-emulsification step. Copyright © 2016 Elsevier Ltd. All rights reserved.

  5. Supercritical fluid extraction of peach (Prunus persica) almond oil: process yield and extract composition.

    Science.gov (United States)

    Mezzomo, Natália; Mileo, Bruna R; Friedrich, Maria T; Martínez, Julian; Ferreira, Sandra R S

    2010-07-01

    Peach kernels are industrial residues from the peach processing, contain oil with important therapeutic properties and attractive nutritional aspects because of the high concentration of oleic and linoleic acids. The extraction method used to obtain natural compounds from raw matter is critical for product quality definition. Thus, the aim of this work was to compare peach almond extraction yields obtained by different procedures: soxhlet extractions (Sox) with different solvents; hydrodistillation (HD); ethanolic maceration (Mac) followed by fractionation with various solvents, and supercritical fluid extraction (SFE) at 30, 40 and 50 degrees C and at 100, 200 and 300bar, performed with pure CO(2) and with a co-solvent. The extracts were evaluated with respect to fatty acid composition (FAC), fractionated chemical profile (FCP) and total phenolic content (TPC). The Sox total yields were generally higher than those obtained by SFE. The crossover pressure for SFE was between 260 and 280bar. The FAC results show oleic and linoleic acids as main components, especially for Sox and SFE extracts. The FCP for samples obtained by Sox and Mac indicated the presence of benzaldehyde and benzyl alcohol, components responsible for almond flavor and with important industrial uses, whereas the SFE extracts present a high content of a possible flavonoid. The higher TPC values were obtained by Sox and Mac with ethanol. In general, the maximum pressure in SFE produced the highest yield, TPC and oleic acid content. The use of ethanol at 5% as co-solvent in SFE did not result in a significant effect on any evaluated parameter. The production of peach almond oil through all techniques is substantially adequate and SFE presented advantages, with respect to the quality of the extracts due to the high oleic acid content, as presented by some Sox samples. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

  6. Asphaltene precipitation and its effects on the vapour extraction (VAPEX) heavy oil recovery process

    Energy Technology Data Exchange (ETDEWEB)

    Luo, P.; Wang, X.; Gu, Y. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Regina Univ., SK (Canada). Petroleum Technology Research Centre; Zhang, H. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Core Laboratories Canada Ltd., Calgary, AB (Canada); Moghadam, L. [Fekete Associates Inc., Calgary, AB (Canada)

    2008-10-15

    One of the most important physical phenomena during the solvent vapour extraction (VAPEX) of heavy oil recovery is asphaltene precipitation. After the asphaltene precipitation occurs, the produced heavy oil is deasphalted in-situ, resulting in a lower viscosity and better quality. However, precipitated asphaltenes may plug some small pores of the reservoir formation, thus reducing its permeability. This paper examined the effects of three operating factors on the asphaltene precipitation during the VAPEX process, notably solvent type; operating pressure; and sand-pack permeability. Eight VAPEX tests were conducted to recover two different Lloydminster heavy oil samples from a rectangular sand-packed physical model with a butane mixture and propane as the respective solvents. The accumulative heavy oil and solvent production from the physical model were measured in the entire VAPEX process. The paper described the materials, experimental set-up, and experimental preparation. The VAPEX test was also explained. Results were presented for sand consolidation; solvent effect; pressure effect; and permeability effect. It was concluded that when the extracting solvent is in a liquid-gas state, asphaltene precipitation occurs and leads to in-situ deasphalting. 15 refs., 3 tabs., 6 figs.

  7. Extraction of siphonochilus aethiopicus essential oil by steam distillation

    CSIR Research Space (South Africa)

    Malaka, MS

    2017-04-01

    Full Text Available was to optimize the process parameters of steam distillation for the extraction of oil from African ginger rhizomes. This technology is the oldest and well known for extracting essential oils due to its economic viability and the higher final oil purity...

  8. The ultrasound-assisted aqueous extraction of rice bran oil.

    Science.gov (United States)

    Khoei, Maryam; Chekin, Fereshteh

    2016-03-01

    In this work, aqueous extraction of rice bran oil was done without and with ultrasound pretreatment. Key factors controlling the extraction and optimal operating conditions were identified. The highest extraction efficiency was found at pH=12, temperature of 45°C, agitation speed of 800rpm and agitation time of 15min, ultrasound treatment time of 70min and ultrasound treatment temperature of 25°C. Moreover, extraction yields were compared to ultrasound-assisted aqueous extraction and Soxhlet extraction. The results showed that the yield of rice bran oil at ultrasound-assisted aqueous extraction was close to the yield of oil extracted by hexane Soxhlet extraction. This result implied that the yield of rice bran oil was significantly influenced by ultrasound. With regard to quality, the oil extracted by ultrasound-assisted aqueous process had a lower content of free fatty acid and lower color imparting components than the hexane-extracted oil. Also, effect of parboiling of paddy on hexane and ultrasound-assisted aqueous extraction was studied. Both extraction methods gives higher percentage of oil from par boiled rice bran compared with raw rice bran. This may be due to the fact that parboiling releases the oil. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Quality of Cosmetic Argan Oil Extracted by Supercritical Fluid Extraction from Argania spinosa L.

    Directory of Open Access Journals (Sweden)

    Chouaa Taribak

    2013-01-01

    Full Text Available Argan oil has been extracted using supercritical CO2. The influence of the variables pressure (100, 200, 300, and 400 bar and temperature (35, 45, 55°C was investigated. The best extraction yields were achieved at a temperature of 45°C and a pressure of 400 bar. The argan oil extracts were characterized in terms of acid, peroxide and iodine values, total tocopherol, carotene, and fatty acids content. Significant compositional differences were not observed between the oil samples obtained using different pressures and temperatures. The antioxidant capacity of the argan oil samples was high in comparison to those of walnut, almond, hazelnut, and peanut oils and comparable to that of pistachio oil. The physicochemical parameters of the extracted oils obtained by SFE, Soxhlet, and traditional methods are comparable. The technique used for oil processing does not therefore markedly alter the quality of argan oil.

  10. Soy Sauce Residue Oil Extracted by a Novel Continuous Phase Transition Extraction under Low Temperature and Its Refining Process.

    Science.gov (United States)

    Zhao, Lichao; Zhang, Yong; He, Liping; Dai, Weijie; Lai, Yingyi; Yao, Xueyi; Cao, Yong

    2014-04-09

    On the basis of previous single-factor experiments, extraction parameters of soy sauce residue (SSR) oil extracted using a self-developed continuous phase transition extraction method at low temperature was optimized using the response surface methodology. The established optimal conditions for maximum oil yield were n-butane solvent, 0.5 MPa extraction pressure, 45 °C temperature, 62 min extraction time, and 45 mesh raw material granularity. Under these conditions, the actual yield was 28.43% ± 0.17%, which is relatively close to the predicted yield. Meanwhile, isoflavone was extracted from defatted SSR using the same method, but the parameters and solvent used were altered. The new solvent was 95% (v/v) ethanol, and extraction was performed under 1.0 MPa at 60 °C for 90 min. The extracted isoflavones, with 0.18% ± 0.012% yield, mainly comprised daidzein and genistein, two kinds of aglycones. The novel continuous phase transition extraction under low temperature could provide favorable conditions for the extraction of nonpolar or strongly polar substances. The oil physicochemical properties and fatty acids compositions were analyzed. Results showed that the main drawback of the crude oil was the excess of acid value (AV, 63.9 ± 0.1 mg KOH/g) and peroxide value (POV, 9.05 ± 0.3 mmol/kg), compared with that of normal soybean oil. However, through molecular distillation, AV and POV dropped to 1.78 ± 0.12 mg KOH/g and 5.9 ± 0.08 mmol/kg, respectively. This refined oil may be used as feedstuff oil.

  11. Green ultrasound-assisted extraction of carotenoids from pomegranate wastes using vegetable oils.

    Science.gov (United States)

    Goula, Athanasia M; Ververi, Maria; Adamopoulou, Anna; Kaderides, Kyriakos

    2017-01-01

    The objective of this work was to develop a new process for pomegranate peels application in food industries based on ultrasound-assisted extraction of carotenoids using different vegetable oils as solvents. In this way, an oil enriched with antioxidants is produced. Sunflower oil and soy oil were used as alternative solvents and the effects of various parameters on extraction yield were studied. Extraction temperature, solid/oil ratio, amplitude level, and extraction time were the factors investigated with respect to extraction yield. Comparative studies between ultrasound-assisted and conventional solvent extraction were carried out in terms of processing procedure and total carotenoids content. The efficient extraction period for achieving maximum yield of pomegranate peel carotenoids was about 30min. The optimum operating conditions were found to be: extraction temperature, 51.5°C; peels/solvent ratio, 0.10; amplitude level, 58.8%; solvent, sunflower oil. A second-order kinetic model was successfully developed for describing the mechanism of ultrasound extraction under different processing parameters. Copyright © 2016 Elsevier B.V. All rights reserved.

  12. Extraction, Characterization and Modification of Castor Seed Oil

    Directory of Open Access Journals (Sweden)

    A. D. MOHAMMED

    2006-01-01

    Full Text Available This paper carried out experimental study, through extraction and characterization of both crude and refined castor oil. Normal hexane was used as solvent for the extraction process. The oil produced was refined through degumming, neutralization and bleaching process using local adsorbent (activated clay. The characterization analysis revealed that tested parameters, which include specific gravity, refractive index, acid value, saponification value and iodine value for both crude and refined castor oil produced, were within the ASTM standard specifications. In fact the iodine value obtained (84.8 for the refined oil indicates that the oil could certainly be used as lubricant, hydraulic break fluid and protecting coatings. The oil was modified via sulphation method to produce Turkey – red oil that was tested on wooden material, paper and cloth. The test revealed that the Turkey – red oil produced is suitable to be used as a good dying agent and polish.

  13. Optimization of oil extraction process by the method of mathematical modeling

    Directory of Open Access Journals (Sweden)

    М. V. Kopylov

    2017-01-01

    Full Text Available The main objective of the experimental study of all processes is the analysis, study and generalization of all available results. In accordance with the idea of indexing search experiment was carried out in several stages. The number of stages and steps on each of which depended on the results of the previous stage and the ultimate goal of research. The ultimate goal of the study is to determine the optimum process conditions. Studies vegetable oil extraction process was conducted in a pilot plant set up on the basis of a single-screw Oil-presses. To ensure maximum efficiency Oil-presses without loss of quality of the finished necessary to ensure continuity and uniformity of oilseeds admission hopper. To process the experimental studies, the software complex STATISTICA 10 was applied. To obtain the regression equation, the matrix data was processed using the MS Excel software package. It is found that in order to provide the required performance Oil-presses need to set the angular speed of the screw in the range of 5.5–6.4 s-1, the value of the annular gap between the screw and curb chamber is 0.7–0.9 mm, the quantity gap curb camera of 0.16–0.18 mm. To optimize the process, the output values of the parameters converted into a dimensionless scale desirability d. In the course of the research found that the desirability of the D function, which characterizes the adequacy of the obtained values, has an extreme experience in the 8 and equal to 0.8. On the basis of the following parameters should be considered optimal obtained data: the angular speed of the screw of 6.6 to 1, the value of the annular gap between the screw and camera curb 0.92 mm, the magnitude of the gap.

  14. Extraction of Lepidium apetalum Seed Oil Using Supercritical Carbon Dioxide and Anti-Oxidant Activity of the Extracted Oil

    Directory of Open Access Journals (Sweden)

    Xuchong Tang

    2011-12-01

    Full Text Available The supercritical fluid extraction (SFE of Lepidium apetalum seed oil and its anti-oxidant activity were studied. The SFE process was optimized using response surface methodology (RSM with a central composite design (CCD. Independent variables, namely operating pressure, temperature, time and flow rate were evaluated. The maximum extraction of Lepidium apetalum seed oil by SFE-CO2 (about 36.3% was obtained when SFE-CO2 extraction was carried out under the optimal conditions of 30.0 MPa of pressure, 70 °C of temperature, 120 min of extraction time and 25.95 L/h of flow rate. GC-MS analysis showed the presence of four fatty acids in Lepidium apetalum seed oil, with a high content (91.0% of unsaturated fatty acid. The anti-oxidant activity of the oil was assessed by the 2,2-diphenyl-1-picrylhydrazyl (DPPH radical-scavenging assay and 2,2′-azino- bis(3-ethylbenzthiazoline-6-sulphonic acid diammonium salt (ABTS test. Lepidium apetalum seed oil possessed a notable concentration-dependent antioxidant activity, with IC50 values of 1.00 and 3.75 mg/mL, respectively.

  15. Extraction and analysis of Jatropha curcas L. seed oil | Shivani ...

    African Journals Online (AJOL)

    In this study, extraction of Jatropha oil from seeds was optimized using organic solvents. The effects of parameters on the oil extraction namely type of organic solvents and different techniques were also investigated to optimize the processing conditions for achieving maximum oil yield. The acid value and antioxidant ...

  16. Selective solvent extraction of oils

    Energy Technology Data Exchange (ETDEWEB)

    1938-04-09

    In the selective solvent extraction of naphthenic base oils, the solvent used consists of the extract obtained by treating a paraffinic base oil with a selective solvent. The extract, or partially spent solvent is less selective than the solvent itself. Selective solvents specified for the extraction of the paraffinic base oil are phenol, sulphur dioxide, cresylic acid, nitrobenzene, B:B/sup 1/-dichlorethyl ether, furfural, nitroaniline and benzaldehyde. Oils treated are Coastal lubricating oils, or naphthenic oils from the cracking, or destructive hydrogenation of coal, tar, lignite, peat, shale, bitumen, or petroleum. The extraction may be effected by a batch or counter-current method, and in the presence of (1) liquefied propane, or butane, or naphtha, or (2) agents which modify the solvent power such as, water, ammonia, acetonitrile, glycerine, glycol, caustic soda or potash. Treatment (2) may form a post-treatment effected on the extract phase. In counter-current treatment in a tower some pure selective solvent may be introduced near the raffinate outlet to wash out any extract therefrom.

  17. A MODELLING APPROACH TO EXTRA VIRGIN OLIVE OIL EXTRACTION

    Directory of Open Access Journals (Sweden)

    Marco Daou

    2007-12-01

    Full Text Available In the present work is described a feasibility assessment for a new approach in virgin olive oil production control system. A predicting or simulating algorithm is implemented as artificial neural network based software, using literature found data concerning parameters related to olive grove, process, machine. Test and validation proved this tool is able to answer two different frequently asked questions by olive oil mill operators, using few agronomic and technological parameters with time and cost saving: – which quality level is up to oil extracted from defined olive lot following a defined process (predicting mode; – which process and machine parameters set would determine highest quality level for oil extracted from a defined olive lot (simulating mode.

  18. Effect of Different Sterilization Methods on the Extracted Oil from Oil Palm Fruit

    International Nuclear Information System (INIS)

    Hasimah Kasmin; Hasimah Kasmin; Roila Awang; Azwan Mat Lazim

    2015-01-01

    Sterilization is important process during the processing of oil palm fruits in order to produce crude palm oil (CPO). This process can be carried out using steam (conventional method), dry heating or wet heating method. In this study, the effectiveness of the dry heating and wet heating method for sterilization and solvent extraction were carried out. The sterilization time of these two methods were varied at 30, 60 and 90 min in order to determine their effectiveness on the oil extraction and their quality. Results showed that, at 30 min of sterilization, the wet heating produced a higher percentage of oil extraction compared to the conventional and dry heating, with average of 27.65 %, 19.01 % and 20.21 % respectively. In comparison with the conventional method, both sterilization methods gave better FFA and DOBI results. This can be seen where the average of free fatty acid (FFA) content for proposed sterilization method was between 0.37 % to 0.93 % while, average deterioration of bleach ability index (DOBI) was from 4.89 to 6.12. The average carotene content was in agreement with the conventional method at a range of 644.64 ppm to 764.80 ppm. (author)

  19. Modeling and optimization of extraction process of eucalyptus essential oil (Eucalyptus globulus

    Directory of Open Access Journals (Sweden)

    Jeancarlos Moreno

    2010-06-01

    Full Text Available In this paper we have studied the effect of the moisture from the eucalyptus leaf and the time of extraction on the yield of essential oil and the production cost. We took into account parameters such as steam temperature, pressure extraction, porous bed, steam flow and temperature of condensation. A Central Composite Rotational Design was used to evaluate optimum extraction areas and the cost that would follow, searching always to increase yields and reduce costs. According to this design, the extraction with the lowest production costs (0.57 Nuevos Soles by mL of essential oil is reached when the leaves have moisture between 25 and 30% and are extracted with times between 98 and 126 min

  20. Taggiasca extra virgin olive oil colonization by yeasts during the extraction process.

    Science.gov (United States)

    Ciafardini, G; Cioccia, G; Zullo, B A

    2017-04-01

    The opalescent appearance of the newly produced olive oil is due to the presence of solid particles and microdrops of vegetation water in which the microorganisms from the olives' carposphere are trapped. Present research has demonstrated that the microbiota of the fresh extracted olive oil, produced in the mills, is mainly composed of yeasts and to a lesser extent of molds. The close link between the composition of the microbiota of the olives' carposphere undergoing to processing, and that of the microbiota of the newly produced olive oil, concerns only the yeasts and molds, given that the bacterial component is by and large destroyed mainly in the kneaded paste during the malaxation process. Six physiologically homogenous yeast groups were highlighted in the wash water, kneaded paste and newly produced olive oil from the Taggiasca variety which had been collected in mills located in the Liguria region. The more predominant yeasts of each group belonged to a single species called respectively: Kluyveromyces marxianus, Candida oleophila, Candida diddensiae, Candida norvegica, Wickerhamomyces anomalus and Debaryomyces hansenii. Apart from K. marxianus, which was found only in the wash water, all the other species were found in the wash water and in the kneaded paste as well as in the newly produced olive oil, while in the six-month stored olive oil, was found only one physiologically homogeneous group of yeast represented by the W. anomalus specie. These findings in according to our previous studies carried out on other types of mono varietal olive oils, confirms that the habitat of the Taggiascas' extra virgin olive oil, had a strong selective pressure on the yeast biota, allowing only to a few member of yeast species, contaminating the fresh product, to survive and reproduce in it during storage. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. Optimal Extraction and Evaluation on the Oil Content of Citronella Oil Extracted From Cymbopogon Nardus

    International Nuclear Information System (INIS)

    Weng, D.C.J.; Jalifah Latip; Siti Aishah Hasbullah; Sastrohamidjojo, H.

    2015-01-01

    An investigation on the extraction of citronella oil from Cymbopogon nardus (C. nardus) using a custom made medium scale steam distillation apparatus has been conducted. The Clevenger apparatus was used to generate a continuous flow of the hydrosol, creating an efficient distillation system. In the case for C. nardus leave samples orientation; the sleeping/ standing and close/ loose packing in steam distillator was found to have significant effects on the yield of extraction. The 3.5 hours distillation process produced an extraction yield of 0.64 % in sleeping position of the leaves as compared to the standing position (0.43 %), while the loose packing (0.70 %) has almost two fold of yield percentage as compared to the close-packing (0.40 %) of the leaves. Therefore, the steam distillation of C. nardus leaves using a custom made medium scale steam distillation apparatus was found to be most effective in the combination of sleeping position with a loose packing. Furthermore, the age of C. nardus leaves also affect the physical and chemical quality of the citronella oil extracted. The younger leaves produced citronella oil that consists mainly of citronellal, citronellol and geraniol while the older leaves contained a high composition of citral. (author)

  2. Parameters Affecting the Extraction Process of Jatropha curcas Oil Using a Single Screw Extruder

    Directory of Open Access Journals (Sweden)

    Ali Nurrakhmad Siregar

    2015-07-01

    Full Text Available The most commonly used technique to separate oil and cake from J. curcas seeds is mechanical extraction. It uses simple tools such as a piston and a screw extruder to produce high pressure, driven by hand or by engine. A single screw extruder has one screw rotating inside the barrel and materials simultaneously flow from the feed to the die zone. The highest oil yield can be obtained by a well-designed oil press as well as finding the optimum conditions for all parameters involved during the extraction process. The influence of the parameters in a single screw extruder was studied using finite element analysis and computational fluid dynamics simulation with ANSYS POLYFLOW. The research focused on predicting the velocity, pressure and shear rate in the metering section that influenced the screw rotational speed and mass flow rate. The obtained results revealed that increasing the screw rotational speed will increase the pressure, velocity and shear rate. Meanwhile, increasing the mass flow rate results in decreasing the pressure while the velocity and shear rate remain constant.

  3. Experimental Study On The Optimization Of Extraction Process Of ...

    African Journals Online (AJOL)

    The objective is to study the extraction process of garlic oil and its antibacterial effects. Materials and Methods: CO2 Supercritical extraction was used to investigate the optimal processing conditions for garlic oil extraction; filter paper test and suspension dilution test were applied to determine the bacteriostatic action of ...

  4. Glycerol extracting dealcoholization for the biodiesel separation process.

    Science.gov (United States)

    Ye, Jianchu; Sha, Yong; Zhang, Yun; Yuan, Yunlong; Wu, Housheng

    2011-04-01

    By means of utilizing sunflower oil and Jatropha oil as raw oil respectively, the biodiesel transesterification production and the multi-stage extracting separation were carried out experimentally. Results indicate that dealcoholized crude glycerol can be utilized as the extracting agent to achieve effective separation of methanol from the methyl ester phase, and the glycerol content in the dealcoholized methyl esters is as low as 0.02 wt.%. For the biodiesel separation process utilizing glycerol extracting dealcoholization, its technical and equipment information were acquired through the rigorous process simulation in contrast to the traditional biodiesel distillation separation process, and results show that its energy consumption decrease about 35% in contrast to that of the distillation separation process. The glycerol extracting dealcoholization has sufficient feasibility and superiority for the biodiesel separation process. Copyright © 2011 Elsevier Ltd. All rights reserved.

  5. Supercritical fluid extraction of silicone oil from uranate microspheres prepared by sol-gel process

    International Nuclear Information System (INIS)

    Kumar, R.; Venkatakrishnan, R.; Sivaraman, N.; Srinivasan, T.G.; Vasudeva Rao, P.R.

    2005-01-01

    Supercritical fluid extraction of silicone oil from urania microspheres prepared through sol-gel route was investigated. The influence of pressure, temperature, and flow rate on the extraction efficiency was studied. Experimental conditions were optimised for the complete removal of silicone oil from urania microspheres. (author)

  6. Critical review of supercritical carbon dioxide extraction of selected oil seeds

    Directory of Open Access Journals (Sweden)

    Sovilj Milan N.

    2010-01-01

    Full Text Available Supercritical carbon dioxide extraction, as a relatively new separation technique, can be used as a very efficient process in the production of essential oils and oleoresins from many of plant materials. The extracts from these materials are a good basis for the new pharmaceutical products and ingredients in the functional foods. This paper deals with supercritical carbon dioxide extraction of selected oil seeds which are of little interest in classical extraction in the food industry. In this article the process parameters in the supercritical carbon dioxide extraction, such as pressure, temperature, solvent flow rate, diameter of gound materials, and moisture of oil seed were presented for the following seeds: almond fruits, borage seed, corn germ, grape seed, evening primrose, hazelnut, linseed, pumpkin seed, walnut, and wheat germ. The values of investigated parameters in supercritical extraction were: pressure from 100 to 600 bar, temperature from 10 to 70oC, diameter of grinding material from 0.16 to 2.0 mm, solvent flow used from 0.06 to 30.0 kg/h, amount of oil in the feed from 10.0 to 74.0%, and moisture of oil seed from 1.1 to 7.5%. The yield and quality of the extracts of all the oil seeds as well as the possibility of their application in the pharmaceutical and food, industries were analyzed.

  7. Virgin almond oil: Extraction methods and composition

    Energy Technology Data Exchange (ETDEWEB)

    Roncero, J.M.; Alvarez-Orti, M.; Pardo-Gimenez, A.; Gomez, R.; Rabadan, A.; Pardo, J.E.

    2016-07-01

    In this paper the extraction methods of virgin almond oil and its chemical composition are reviewed. The most common methods for obtaining oil are solvent extraction, extraction with supercritical fluids (CO2) and pressure systems (hydraulic and screw presses). The best industrial performance, but also the worst oil quality is achieved by using solvents. Oils obtained by this method cannot be considered virgin oils as they are obtained by chemical treatments. Supercritical fluid extraction results in higher quality oils but at a very high price. Extraction by pressing becomes the best option to achieve high quality oils at an affordable price. With regards chemical composition, almond oil is characterized by its low content in saturated fatty acids and the predominance of monounsaturated, especially oleic acid. Furthermore, almond oil contains antioxidants and fat-soluble bioactive compounds that make it an oil with interesting nutritional and cosmetic properties.

  8. Virgin almond oil: Extraction methods and composition

    International Nuclear Information System (INIS)

    Roncero, J.M.; Alvarez-Orti, M.; Pardo-Gimenez, A.; Gomez, R.; Rabadan, A.; Pardo, J.E.

    2016-01-01

    In this paper the extraction methods of virgin almond oil and its chemical composition are reviewed. The most common methods for obtaining oil are solvent extraction, extraction with supercritical fluids (CO2) and pressure systems (hydraulic and screw presses). The best industrial performance, but also the worst oil quality is achieved by using solvents. Oils obtained by this method cannot be considered virgin oils as they are obtained by chemical treatments. Supercritical fluid extraction results in higher quality oils but at a very high price. Extraction by pressing becomes the best option to achieve high quality oils at an affordable price. With regards chemical composition, almond oil is characterized by its low content in saturated fatty acids and the predominance of monounsaturated, especially oleic acid. Furthermore, almond oil contains antioxidants and fat-soluble bioactive compounds that make it an oil with interesting nutritional and cosmetic properties.

  9. Oil Extraction from “Morelos Rice” Bran: Kinetics and Raw Oil Stability

    Directory of Open Access Journals (Sweden)

    J. Zúñiga-Diaz

    2017-01-01

    Full Text Available “Morelos rice” is a variety of rice with certificate of denomination of origin. It is a large grain of opaque appearance and extra large size that is grown exclusively in Morelos state (Mexico. Thus, the quality and characteristics of its rice bran may affect the kinetic of the extraction process of its oil as well as its stability. Therefore, this work is oriented to determine the extraction kinetics of its oil and its oxidative stability. The latter one is obtained through the proposal of a method based on open-circuit potential measurements. The results showed that the rice bran has 21.44% of raw oil, with a chemical composition (based on fatty acids of 48.48% oleic acid, 35.26% linoleic acid, and 14.54% palmitic acid, as well as a free fatty acid content of 8.15%. A high percentage of its oil content can be recovered in a short time at room temperature, and its extraction kinetics is a function of both the washing and the diffusion of its oil. Under storage conditions the raw oil has a high stability, at least 8 months, and its oxidative stability was of 24, 9, and 7 hours at 50°C, 80°C, and 110°C, respectively.

  10. Special features of SCF solid extraction of natural products: deoiling of wheat gluten and extraction of rose hip oil

    Directory of Open Access Journals (Sweden)

    Eggers R.

    2000-01-01

    Full Text Available Supercritical CO2 extraction has shown great potential in separating vegetable oils as well as removing undesirable oil residuals from natural products. The influence of process parameters, such as pressure, temperature, mass flow and particle size, on the mass transfer kinetics of different natural products has been studied by many authors. However, few publications have focused on specific features of the raw material (moisture, mechanical pretreatment, bed compressibility, etc., which could play an important role, particularly in the scale-up of extraction processes. A review of the influence of both process parameters and specific features of the material on oilseed extraction is given in Eggers (1996. Mechanical pretreatment has been commonly used in order to facilitate mass transfer from the material into the supercritical fluid. However, small particle sizes, especially when combined with high moisture contents, may lead to inefficient extraction results. This paper focuses on the problems that appear during scale-up in processes on a lab to pilot or industrial plant scale related to the pretreatment of material, the control of initial water content and vessel shape. Two applications were studied: deoiling of wheat gluten with supercritical carbon dioxide to produce a totally oil-free (< 0.1 % oil powder (wheat gluten and the extraction of oil from rose hip seeds. Different ways of pretreating the feed material were successfully tested in order to develop an industrial-scale gluten deoiling process. The influence of shape and size of the fixed bed on the extraction results was also studied. In the case of rose hip seeds, the present work discusses the influence of pretreatment of the seeds prior to the extraction process on extraction kinetics.

  11. Profitability Analysis of Soybean Oil Processes.

    Science.gov (United States)

    Cheng, Ming-Hsun; Rosentrater, Kurt A

    2017-10-07

    Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV), break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP), is profitable when the capacity is larger than 17 million kg of annual oil production.

  12. Profitability Analysis of Soybean Oil Processes

    Directory of Open Access Journals (Sweden)

    Ming-Hsun Cheng

    2017-10-01

    Full Text Available Soybean oil production is the basic process for soybean applications. Cash flow analysis is used to estimate the profitability of a manufacturing venture. Besides capital investments, operating costs, and revenues, the interest rate is the factor to estimate the net present value (NPV, break-even points, and payback time; which are benchmarks for profitability evaluation. The positive NPV and reasonable payback time represent a profitable process, and provide an acceptable projection for real operating. Additionally, the capacity of the process is another critical factor. The extruding-expelling process and hexane extraction are the two typical approaches used in industry. When the capacities of annual oil production are larger than 12 and 173 million kg respectively, these two processes are profitable. The solvent free approach, known as enzyme assisted aqueous extraction process (EAEP, is profitable when the capacity is larger than 17 million kg of annual oil production.

  13. Extraction by Dry Rendering Methode and Characterization Fish Oil of Catfish Viscera Fat by Product of Smooked Fish Processing

    Directory of Open Access Journals (Sweden)

    Kamini Kamini

    2017-02-01

    Full Text Available AbstractThe catfish viscera fat, is cathfish processing by-products, has potential to be used as a source of rawmaterial for production of fish oil. This study aimed to analyze the value of proximate, heavy metal contentand fatty acid profile of catfish viscera fat (Pangasius hypopthalmus and characterized fish oil extracted bydry rendering in various temperature and time than compared it to fish oil extracted by stove heating toobtain the best treatment. Proximate, heavy metal residue, and the fatty acid profile analysis were conductedfor characterizing catfish viscera fat. Fish oil extraction was conducted by dry rendering in varioustemperatures of 50, 60, 70, 80 °C for 1, 2, and 3 hours. Fish oil quality was determined by the chemicalcharacteristics i.e. PV, FFA, anisidin and TOTOX. The results of the study showed that fat content of catfishfat viscera was 88.19 %, the heavy metals content was below SNI standart to be consumed, and fatty acidprofile composition was SFA>MUFA>PUFA. The highest fatty acid content was oleic acid. The best fish oilquality was resulted on temperature extraction of 50°C for 2 hours with yield value, PV, FFA, anisidin, andTOTOX were 45.17 %, 2.77 meq/kg, 0.83 %, 2.86 meq/kg, 8.39 meq/kg respectively. This result was notsignificantly different with fish oil extracted by the stove heating expect for yield and PV were 80.11% and6.52 meq/kg, respectively.

  14. Solvent-free microwave extraction of essential oil from Melaleuca leucadendra L.

    Directory of Open Access Journals (Sweden)

    Widya Ismanto Aviarina

    2018-01-01

    Full Text Available Cajuput (Melaleuca leucadendra L. oil is one of potential commodity that provides an important role for the country’s foreign exchange but the extraction of these essential oil is still using conventional method such as hydrodistillation which takes a long time to produce essential oil with good quality. Therefore it is necessary to optimize the extraction process using a more effective and efficient method. So in this study the extraction is done using solvent-free microwave extraction method that are considered more effective and efficient than conventional methods. The optimum yield in the extraction of cajuput oil using solvent-free microwave extraction method is 1.0674%. The optimum yield is obtained on the feed to distiller (F/D ratio of 0.12 g/mL with microwave power of 400 W. In the extraction of cajuput oil using solvent-free microwave extraction method is performed first-order and second-order kinetics modelling. Based on kinetics modelling that has been done, it can be said that the second-order kinetic model (R2 = 0.9901 can be better represent experimental results of extraction of cajuput oil that using solvent-free microwave extraction method when compared with the first-order kinetic model (R2 = 0.9854.

  15. Alternative oil extraction methods from Echium plantagineum L. seeds using advanced techniques and green solvents.

    Science.gov (United States)

    Castejón, Natalia; Luna, Pilar; Señoráns, Francisco J

    2018-04-01

    The edible oil processing industry involves large losses of organic solvent into the atmosphere and long extraction times. In this work, fast and environmentally friendly alternatives for the production of echium oil using green solvents are proposed. Advanced extraction techniques such as Pressurized Liquid Extraction (PLE), Microwave Assisted Extraction (MAE) and Ultrasound Assisted Extraction (UAE) were evaluated to efficiently extract omega-3 rich oil from Echium plantagineum seeds. Extractions were performed with ethyl acetate, ethanol, water and ethanol:water to develop a hexane-free processing method. Optimal PLE conditions with ethanol at 150 °C during 10 min produced a very similar oil yield (31.2%) to Soxhlet using hexane for 8 h (31.3%). UAE optimized method with ethanol at mild conditions (55 °C) produced a high oil yield (29.1%). Consequently, advanced extraction techniques showed good lipid yields and furthermore, the produced echium oil had the same omega-3 fatty acid composition than traditionally extracted oil. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Optimizing conditions for enzymatic extraction of sunflower oil

    Directory of Open Access Journals (Sweden)

    Badr, F. H.

    1992-10-01

    Full Text Available Sunflower seed oil was extracted with an enzymatic processes using different hydrolytic enzymes: cellulase, hemicellulase, animal proteinase, acid proteinase, pectinase and pectinex, as compared to enzyme - free aqueous extraction. All the hydrolytic enzymes enhanced oil extraction from sunflower seeds. The most optimal conditions for oil extraction from sunflower seeds were: 2% enzyme concentration, 30% substrate concentration and 3 hrs period. Using Boganov and Buchkov equation showed that time must be prolonged to get higher yields. The maximum yield during 3 hrs extraction with enzymatic process ranged between 44,5%-57,1% of the soxhlet extractable oil. The potency of the investigated enzymes in extracting oil was in the following order: acid proteinase > cellulase > hemicellulase > animal proteinase > pectinex > pectinase when compared at the previous optimal conditions.

    Aceite de semilla de girasol fue extraído mediante un proceso enzimático usando diferentes enzimas hidrolíticos: celulasa, hemicelulasa, proteinasa animal, proteinasa acida, pectinasa y pectinex, comparando con la extracción acuosa libre de enzima. Todos los enzimas hidrolíticos incrementan la extracción de aceites de semilla de girasol. Las condiciones óptimas para la extracción de aceite a partir de semillas de girasol fueron: 2% de concentración de enzima, 30% de concentración de sustrato y un período de 3 horas. La ecuación de Boganov y Buchkov mostró que el tiempo debe ser prolongado para alcanzar altos rendimientos. El máximo rendimiento durante tres horas de extracción con proceso enzimático osciló entre el 44,5%-57,1% del aceite extraído con soxhlet. La potencia de los enzimas investigados en la extracción de aceite siguió el orden: proteinasa acida > celulasa > hemicelulasa > proteinasa animal > pectinex > pectinasa cuando fue previamente comparado con las condiciones óptimas.

  17. Kinetic and Thermodynamics studies for Castor Oil Extraction Using Subcritical Water Technology.

    Science.gov (United States)

    Abdelmoez, Wael; Ashour, Eman; Naguib, Shahenaz M; Hilal, Amr; Al Mahdy, Dalia A; Mahrous, Engy A; Abdel-Sattar, Essam

    2016-06-01

    In this work both kinetic and thermodynamics of castor oil extraction from its seeds using subcritical water technique were studied. It was found that the extraction process followed two consecutive steps. In these steps, the oil was firstly extracted from inside the powder by diffusion mechanism. Then the extracted oil, due to extending the extraction time under high temperature and pressure, was subjected to a decomposition reaction following first order mechanism. The experimental data correlated well with the irreversible consecutive unimolecular-type first order mechanism. The values of both oil extraction rate constants and decomposition rate constants were calculated through non-linear fitting using DataFit software. The extraction rate constants were found to be 0.0019, 0.024, 0.098, 0.1 and 0.117 min(-1), while the decomposition rate constants were 0.057, 0.059, 0.014, 0.019 and 0.17 min(-1) at extraction temperatures of 240, 250, 260, 270 and 280°C, respectively. The thermodynamic properties of the oil extraction process were investigated using Arrhenius equation. The values of the activation energy, Ea, and the frequency factor, A, were 73 kJ mol(-1) and 946, 002 min(-1), respectively. The physicochemical properties of the extracted castor oil including the specific gravity, viscosity, acid value, pH value and calorific value were found to be 0.947, 7.487, 1.094 mg KOH/g, 6.1, and 41.5 MJ/Kg, respectively. Gas chromatography analysis showed that ricinoleic acid (83.6%) appears as the predominant fatty acid in the extracted oil followed by oleic acid (5.5%) and linoleic acid (2.3%).

  18. Chemical composition and bioactivity of different oregano (Origanum vulgare) extracts and essential oil.

    Science.gov (United States)

    Teixeira, Bárbara; Marques, António; Ramos, Cristina; Serrano, Carmo; Matos, Olívia; Neng, Nuno R; Nogueira, José M F; Saraiva, Jorge Alexandre; Nunes, Maria Leonor

    2013-08-30

    There is a growing interest in industry to replace synthetic chemicals by natural products with bioactive properties. Aromatic plants are excellent sources of bioactive compounds that can be extracted using several processes. As far as oregano is concerned, studies are lacking addressing the effect of extraction processes in bioactivity of extracts. This study aimed to characterise the in vitro antioxidant and antibacterial properties of oregano (Origanum vulgare) essential oil and extracts (in hot and cold water, and ethanol), and the chemical composition of its essential oil. The major components of oregano essential oil were carvacrol, β-fenchyl alcohol, thymol, and γ-terpinene. Hot water extract had the strongest antioxidant properties and the highest phenolic content. All extracts were ineffective in inhibiting the growth of the seven tested bacteria. In contrast, the essential oil inhibited the growth of all bacteria, causing greater reductions on both Listeria strains (L. monocytogenes and L. innocua). O. vulgare extracts and essential oil from Portuguese origin are strong candidates to replace synthetic chemicals used by the industry. © 2013 Society of Chemical Industry.

  19. Supercritical fluid extraction for the determination of optimum oil recovery conditions

    Energy Technology Data Exchange (ETDEWEB)

    Al-Marzouqi, Ali H.; Zekri, Abdulrazag Y.; Jobe, Baboucarr; Dowaidar, Ali [Chemical and Petroleum Engineering Department, U.A.E. University, P.O. Box: 17555, Al-Ain (United Arab Emirates)

    2007-01-15

    CO{sub 2} under supercritical (SC) conditions is a powerful solvent capable of extracting hydrocarbons from crude oil. The extraction capacity of CO{sub 2} is a function of pressure, temperature and composition of the crude oil. This paper presents the results of a laboratory study investigating the capacity of CO{sub 2} to extract hydrocarbons from an oil-saturated soil under a wide range of pressures and temperatures (80-120 bar for temperatures ranging from 40 to 60 C and 200-300 bar for temperatures varying from 100 to 140 C). The soil samples were collected from Sahel oil filed, which is near Bu Hasa oil field (Abu Dhabi, UAE) where the crude oil was obtained from. The extracted oil from the SC CO{sub 2} process and the residual oil remaining in the soil sample were analyzed by gas chromatography to shed more light on the extraction phenomenon. Extraction efficiency of CO{sub 2} increased with pressure and decreased with temperature. Moreover, the amount of extracted heavy fractions increased with pressure for all temperatures. On the other hand, the amount of extracted heavy hydrocarbons decreased with temperature for the low pressure range (80-120 bar) and remained the same for the pressure range of 250-300 bar. The maximum extraction efficiency of CO{sub 2} was 72.4%, which was obtained at the highest pressure (300 bar) and a temperature of 100 C. (author)

  20. EVALUATION OFAMATHEMATICAL MODEL FOR OIL EXTRACTION FROM OLEAGINOUS SEEDS

    Directory of Open Access Journals (Sweden)

    Giuseppe Toscano

    2007-06-01

    Full Text Available Mechanical extraction from seeds represents an important process in the production of vegetable oils. The efficiency of this step can have an effect on the economic convenience of the entire production chain of vegetable oils. However, the mechanical presses used for extraction are designed following criteria based more on the experience and intuition of the operators than on rigorous analyses of the physical principles involved in the process. In this study we have tested the possibility of applying a mathematical model that reproduces oil extraction from seeds, on a laboratory type of continuous press. In other words, we have compared the results of our mathematical model with those obtained from real extractions with mechanical presses on sunflower seeds. Our model is based on determining the main operating parameters of mechanical extraction, such as temperature, pressure and compression time, and on the knowledge of some physical characteristics of the solid matrix of the seeds. The results obtained are interesting because they include the role of operating parameters involved in extraction while the application of the mathematical model studied here allows, although with potential for improvement, a mathematical instrument to be developed for optimising the sizing and the operating conditions of mechanical presses.

  1. Unconventional oil and gas extraction and animal health.

    Science.gov (United States)

    Bamberger, M; Oswald, R E

    2014-08-01

    The extraction of hydrocarbons from shale formations using horizontal drilling with high volume hydraulic fracturing (unconventional shale gas and tight oil extraction), while derived from methods that have been used for decades, is a relatively new innovation that was introduced first in the United States and has more recently spread worldwide. Although this has led to the availability of new sources of fossil fuels for domestic consumption and export, important issues have been raised concerning the safety of the process relative to public health, animal health, and our food supply. Because of the multiple toxicants used and generated, and because of the complexity of the drilling, hydraulic fracturing, and completion processes including associated infrastructure such as pipelines, compressor stations and processing plants, impacts on the health of humans and animals are difficult to assess definitively. We discuss here findings concerning the safety of unconventional oil and gas extraction from the perspectives of public health, veterinary medicine, and food safety.

  2. Re-Refining of Waste Lubricating Oil by Solvent Extraction

    Directory of Open Access Journals (Sweden)

    Hassan Ali Durrani

    2011-04-01

    Full Text Available Re-refining of waste lubricating oil by solvent extraction is one of the potential techniques. The advantages of solvent extraction technique practically offers from environmental and economic points of view have received due attention. In this paper selection of composite solvent and technique to upgrade the used lubricant oil into base oil has been made. The composite solvent 2-propanol, 1-butanol and butanone have two alcohols that make a binary system reasonably effective. This work also attempts to study the performance of the composite solvent in the extraction process for recovering waste lubricating oil. The key parameters considered were vacuum pressure, temperature and the weight ratio of solvent to waste lubricating oil. The performance was investigated on the PSR (Percentage Sludge Removal and POL (Percent Oil Loss. The best results were obtained using composite solvent 25% 2-propanol, 37% 1-butanol and 38% butanone by a solvent to oil ratio of 6:1 at vacuum pressure 600mmHg and distillation temperature 250oC. The vacuum distilled oil pretreated with the composite solvents was matched to the standard base oil 500N and 150N, found in close agreement and could be used for similar purpose.

  3. Optimisation of steam extraction of oil from maritime pine needles

    OpenAIRE

    Rezzoug , Sid-Ahmed

    2009-01-01

    International audience; Essential oil from pine maritime needles is generally extracted by steam distillation process at atmospheric pressure for more than one hour, or by solvent extraction process. In the last decade, there has been an increasing demand for new extraction techniques enabling automation, shorter extraction time and reduced consumption of organic solvent. In this study, Response Surface Methodology (RSM) was used to evaluate the effects of two processing parameters of an alte...

  4. Supercritical Carbon Dioxide Extraction of the Oak Silkworm (Antheraea pernyi Pupal Oil: Process Optimization and Composition Determination

    Directory of Open Access Journals (Sweden)

    Zhao-Jun Wei

    2012-02-01

    Full Text Available Supercritical carbon dioxide (SC-CO2 extraction of oil from oak silkworm pupae was performed in the present research. Response surface methodology (RSM was applied to optimize the parameters of SC-CO2 extraction, including extraction pressure, temperature, time and CO2 flow rate on the yield of oak silkworm pupal oil (OSPO. The optimal extraction condition for oil yield within the experimental range of the variables researched was at 28.03 MPa, 1.83 h, 35.31 °C and 20.26 L/h as flow rate of CO2. Under this condition, the oil yield was predicted to be 26.18%. The oak silkworm pupal oil contains eight fatty acids, and is rich in unsaturated fatty acids and α-linolenic acid (ALA, accounting for 77.29% and 34.27% in the total oil respectively.

  5. Non-aqueous heavy oil extraction from oil sand

    Energy Technology Data Exchange (ETDEWEB)

    Bohnert, George [National Nuclear Security Administration (United States)

    2011-07-01

    The Kansas City plant operated by Honeywell has a long history of working with DOE NNSA on engineering and manufacturing services supporting national security requirements. The plant has developed a non-aqueous method for heavy oil extraction from oil sands. This method is environmentally friendly as it does not use any external body of water, which would normally be contaminated in the conventional method. It is a 2 phase process consisting of terpene, limonene or alpha pinene, and carbon dioxide. The CO2 and terpene phases are both closed loop systems which minimizes material loss. The limonene and alpha pinene are both naturally derived solvents that come from citrus sources or pine trees respectively. Carbon dioxide is an excellent co-solvent with terpene. There is also a possibility for heat loss recovery during the distillation phase. This process produces clean dry sand. Laboratory tests have concluded that this using non-aqueous liquids process works effectively.

  6. Extraction and characterization of oil bodies from soy beans: a natural source of pre-emulsified soybean oil.

    Science.gov (United States)

    Iwanaga, Daigo; Gray, David A; Fisk, Ian D; Decker, Eric Andrew; Weiss, Jochen; McClements, David Julian

    2007-10-17

    Soybeans contain oil bodies that are coated by a layer of oleosin proteins. In nature, this protein coating protects the oil bodies from environmental stresses and may be utilized by food manufacturers for the same purpose. In this study, oil bodies were extracted from soybean using an aqueous extraction method that involved blending, dispersion (pH 8.6), filtration, and centrifugation steps. The influence of NaCl (0-250 mM), thermal processing (30-90 degrees C, 20 min) and pH (2-8) on the properties and stability of the oil bodies was analyzed using zeta-potential, particle size, and creaming stability measurements. The extracted oil bodies were relatively small ( d 32 approximately 250 nm), and their zeta-potential went from around +12 mV to -20 mV as the pH was increased from 2 to 8, with an isoelectric point around pH 4. The oil bodies were stable to aggregation and creaming at low (pH = 2) and high (pH >/= 6) pH values but were unstable at intermediate values (3 oil bodies were stable to aggregation and creaming at relatively low salt concentrations (NaCl oil bodies were stable to thermal processing from 30 to 90 degrees C (0 mM NaCl, pH 7), but there appeared to be a change in their interfacial properties (decrease in zeta-potential) at temperatures exceeding 60 degrees C. These results suggest that oil bodies extracted from soybeans have similar or improved stability compared to soybean oil emulsions produced from bulk ingredients and may provide a new way of creating functional soy products for the food industry.

  7. Batch extraction modeling of jatropha oil using ethanol and n-hexane

    Energy Technology Data Exchange (ETDEWEB)

    Drummond, Alessandro Araujo; Martins, Marcio Aredes [Universidade Federal de Vicosa (DEA/UFV), MG (Brazil). Dept. de Engenharia Agricola], E-mail: aredes@ufv.br; Santos, Karine Tennis dos [Universidade Federal de Vicosa (DEQ/UFV), MG (Brazil). Dept. de Quimica; Carneiro, Angelica Cassia de Oliveira [Universidade Federal de Vicosa (DFT/UFV), MG (Brazil). Dept. de Fitotecnia; Perez, Ronaldo [Universidade Federal de Vicosa (DTA/UFV), MG (Brazil). Dept. de Tecnologia de Alimentos

    2008-07-01

    Jatropha curcas (Linnaeus.) has been considered as a promising alternative for rainfall regimes from 200 to over 1500 mm per annum. The seed and the oil have many applications, such as purgative, in the treatment of skin infections and rheumatism, in the control of insects, mollusks and fungi, for diesel engines lubricants, in soap and paint production, and mainly for biodiesel production. New technologies should be developed to accomplish the oil production in large scale, since the Brazilian Biodiesel Program stimulates the oilseeds productions. In large scale oil production, the oil is obtained using solvent extraction. The solvent widely used for oil extraction is the n-hexane mainly because of its low vaporization temperature and selectivity to the lipidic fraction. However, the use of n-hexane in small capacity plants makes the process expensive because of high operating losses. Alcohols were exhaustively studied at pilot and industrial scales extraction plants. Ethanol is an efficient and advantageous extraction solvent for oilseeds, being an attractive alternative to extraction grade n-hexane. Therefore, the objective of the present work is to model and to compare the extraction kinetics of jatropha oil by using ethanol and n-hexane. Extractions experiments were performed in a batch extractor at 45 deg C using a liquid-to-solvent ratio of 15:1 (mL solvent/g sample). Samples were taken every 15 min, and extraction time was to 2 h. The kinetics of oil extraction data were fitted to the models reported in literature. For n-hexane and ethanol extractions, the fractional residual oil at 120 minutes was 0.314 and 0.0538, respectively. The models reported in literature were suitable to describe the n-hexane extraction, especially the Duggal model. However, those models were not adequate the model the ethanol extraction (author)

  8. Systems principles of planning the net cost of oil and gas extraction

    Energy Technology Data Exchange (ETDEWEB)

    Ryazanova, N I

    1979-01-01

    The automated system of calculation of ASPC ''oil extraction'' is developed in order to improve the existing system of planning of the oil extracting sector. The most complete expression of the systems construction of the plan is found in the section ''net cost and profit.'' Unity of the production process advances definite requirements for construction of the plan for net cost of oil and gas extraction as the model of this unified process. According to these requirements, the plan for net cost must be developed on the basis of interrelationship of the indicators of the plan for net cost within the section and with indicators of other sections of the plan, methodological unity and continuity of the methods of planning net cost by elements of outlays, articles of calculation and technical-economic factors, methodological continuity of regimes and stages of planning, as well as based on methodological continuity of the control levels. The listed requirements are principles for systems planning of the net cost of oil and gas extraction. These principles guarantee improvement in planning of net cost of oil and gas extraction according to the requirements made for the national economic planning.

  9. The extraction of bitumen from western oil sands. Annual report, July 1991--July 1992

    Energy Technology Data Exchange (ETDEWEB)

    Oblad, A.G.; Bunger, J.W.; Dahlstrom, D.A.; Deo, M.D.; Hanson, F.V.; Miller, J.D.; Seader, J.D.

    1992-08-01

    The University of Utah tar sand research and development program is concerned with research and development on Utah is extensive oil sands deposits. The program has been intended to develop a scientific and technological base required for eventual commercial recovery of the heavy oils from oil sands and processing these oils to produce synthetic crude oil and other products such as asphalt. The overall program is based on mining the oil sand, processing the mined sand to recover the heavy oils and upgrading them to products. Multiple deposits are being investigated since it is believed that a large scale (approximately 20,000 bbl/day) plant would require the use of resources from more than one deposit. The tasks or projects in the program are organized according to the following classification: Recovery technologies which includes thermal recovery methods, water extraction methods, and solvent extraction methods; upgrading and processing technologies which covers hydrotreating, hydrocracking, and hydropyrolysis; solvent extraction; production of specialty products; and environmental aspects of the production and processing technologies. These tasks are covered in this report.

  10. Optimizing oil and xanthorrhizol extraction from Curcuma xanthorrhiza Roxb. rhizome by supercritical carbon dioxide.

    Science.gov (United States)

    Salea, Rinaldi; Widjojokusumo, Edward; Veriansyah, Bambang; Tjandrawinata, Raymond R

    2014-09-01

    Oil and xanthorrhizol extraction from Curcuma xanthorrhiza Roxb. rhizome by supercritical carbon dioxide was optimized using Taguchi method. The factors considered were pressure, temperature, carbon dioxide flowrate and time at levels ranging between 10-25 MPa, 35-60 °C, 10-25 g/min and 60-240 min respectively. The highest oil yield (8.0 %) was achieved at factor combination of 15 MPa, 50 °C, 20 g/min and 180 min whereas the highest xanthorrhizol content (128.3 mg/g oil) in Curcuma xanthorrhiza oil was achieved at a factor combination of 25 MPa, 50 °C, 15 g/min and 60 min. Soxhlet extraction with n-hexane and percolation with ethanol gave oil yield of 5.88 %, 11.73 % and xanthorrhizol content of 42.6 mg/g oil, 75.5 mg/g oil, respectively. The experimental oil yield and xanthorrhizol content at optimum conditions agreed favourably with values predicted by computational process. The xanthorrizol content extracted using supercritical carbon dioxide was higher than extracted using Soxhlet extraction and percolation process.

  11. Storage stability of screwpress-extracted oils and residual meals from CELSS candidate oilseed crops

    Science.gov (United States)

    Stephens, S. D.; Watkins, B. A.; Nielsen, S. S.

    1997-01-01

    The efficacy of using screwpress extraction for oil was studied with three Controlled Ecological Life-Support System (CELSS) candidate oilseed crops (soybean, peanut, and canola), since use of volatile organic solvents for oil extraction likely would be impractical in a closed system. Low oil yields from initial work indicated that a modification of the process is necessary to increase extraction efficiency. The extracted oil from each crop was tested for stability and sensory characteristics. When stored at 23 degC, canola oil and meal were least stable to oxidative rancidity, whereas peanut oil and meal were least stable to hydrolytic rancidity. When stored at 65 degC, soybean oil and canola meal were least stable to oxidative rancidity, whereas peanut oil and meal were least stable to hydrolytic rancidity. Sensory evaluation of the extracted oils used in bread and salad dressing indicated that flavor, odor intensity, acceptability, and overall preference may be of concern for screwpress-extracted canola oil when it is used in an unrefined form. Overall results with screwpress-extracted crude oils indicated that soybean oil may be more stable and acceptable than canola or peanut under typical storage conditions.

  12. Ultrasonic-assisted Aqueous Extraction and Physicochemical Characterization of Oil from Clanis bilineata.

    Science.gov (United States)

    Sun, Mingmei; Xu, Xiao; Zhang, Qiuqin; Rui, Xin; Wu, Junjun; Dong, Mingsheng

    2018-02-01

    Ultrasound-assisted aqueous extraction (UAAE) was used to extract oil from Clanis bilineata (CB), a traditional edible insect that can be reared on a large scale in China, and the physicochemical property and antioxidant capacity of the UAAE-derived oil (UAAEO) were investigated for the first time. UAAE conditions of CB oil was optimized using response surface methodology (RSM) and the highest oil yield (19.47%) was obtained under optimal conditions for ultrasonic power, extraction temperature, extraction time, and ultrasonic interval time at 400 W, 40°C, 50 min, and 2 s, respectively. Compared with Soxhlet extraction-derived oil (SEO), UAAEO had lower acid (AV), peroxide (PV) and p-anisidine values (PAV) as well as higher polyunsaturated fatty acids contents and thermal stability. Furthermore, UAAEO showed stronger antioxidant activities than those of SEO, according to DPPH radical scavenging and β-carotene bleaching tests. Therefore, UAAE is a promising process for the large-scale production of CB oil and CB has a developing potential as functional oil resource.

  13. Improvement of Soybean Oil Solvent Extraction through Enzymatic Pretreatment

    Directory of Open Access Journals (Sweden)

    F. V. Grasso

    2012-01-01

    Full Text Available The purpose of this study is to evaluate multienzyme hydrolysis as a pretreatment option to improve soybean oil solvent extraction and its eventual adaptation to conventional processes. Enzymatic action causes the degradation of the cell structures that contain oil. Improvements in terms of extraction, yield, and extraction rate are expected to be achieved. Soybean flakes and collets were used as materials and hexane was used as a solvent. Temperature, pH, and incubation time were optimized and diffusion coefficients were estimated for each solid. Extractions were carried out in a column, oil content was determined according to time, and a mathematical model was developed to describe the system. The optimum conditions obtained were pH 5.4, 38°C, and 9.7 h, and pH 5.8, 44°C, and 5.8h of treatment for flakes and collets, respectively. Hydrolyzed solids exhibited a higher yield. Diffusion coefficients were estimated between 10-11 and 10-10. The highest diffusion coefficient was obtained for hydrolyzed collets. 0.73 g oil/mL and 0.7 g oil/mL were obtained at 240 s in a column for collets and flakes, respectively. Hydrolyzed solids exhibited a higher yield. The enzymatic incubation accelerates the extraction rate and allows for higher yield. The proposed model proved to be appropriate.

  14. Oil extraction from plant seeds for biodiesel production

    Directory of Open Access Journals (Sweden)

    Yadessa Gonfa Keneni

    2017-04-01

    Full Text Available Energy is basic for development and its demand increases due to rapid population growth, urbanization and improved living standards. Fossil fuels will continue to dominate other sources of energy although it is non-renewable and harm global climate. Problems associated with fossil fuels have driven the search for alternative energy sources of which biodiesel is one option. Biodiesel is renewable, non-toxic, environmental-friendly and an economically feasible options to tackle the depleting fossil fuels and its negative environmental impact. It can be produced from vegetable oils, animal fats, waste oils and algae. However, nowadays, the major feedstocks of biodiesel are edible oils and this has created food vs fuel debate. Therefore, the future prospect is to use non-edible oils, animal fats, waste oils and algae as feedstock for biodiesel. Selection of non-expensive feedstock and the extraction and preparation of oil for biodiesel production is a crucial step due to its relevance on the overall technology. There are three main conventional oil extraction methods: mechanical, chemical/solvent and enzymatic extraction methods. There are also some newly developed oil extraction methods that can be used separately or in combination with the conventional ones, to overcome some disadvantages of the conventional oil extraction methods. This review paper presents, compare and discusses different potential biofuel feedstocks, various oil extraction methods, advantages and disadvantages of different oil extraction methods, and propose future prospective for the improvement of oil extraction methods and sustainability of biodiesel production and utilization.

  15. Oil shales and the nuclear process heat

    International Nuclear Information System (INIS)

    Scarpinella, C.A.

    1974-01-01

    Two of the primary energy sources most dited as alternatives to the traditional fossil fuels are oil shales and nuclear energy. Several proposed processes for the extraction and utilization of oil and gas from shale are given. Possible efficient ways in which nuclear heat may be used in these processes are discussed [pt

  16. Logistic curves, extraction costs and effective peak oil

    International Nuclear Information System (INIS)

    Brecha, Robert J.

    2012-01-01

    Debates about the possibility of a near-term maximum in world oil production have become increasingly prominent over the past decade, with the focus often being on the quantification of geologically available and technologically recoverable amounts of oil in the ground. Economically, the important parameter is not a physical limit to resources in the ground, but whether market price signals and costs of extraction will indicate the efficiency of extracting conventional or nonconventional resources as opposed to making substitutions over time for other fuels and technologies. We present a hybrid approach to the peak-oil question with two models in which the use of logistic curves for cumulative production are supplemented with data on projected extraction costs and historical rates of capacity increase. While not denying the presence of large quantities of oil in the ground, even with foresight, rates of production of new nonconventional resources are unlikely to be sufficient to make up for declines in availability of conventional oil. Furthermore we show how the logistic-curve approach helps to naturally explain high oil prices even when there are significant quantities of low-cost oil yet to be extracted. - Highlights: ► Extraction cost information together with logistic curves to model oil extraction. ► Two models of extraction sequence for different oil resources. ► Importance of time-delay and extraction rate limits for new resources. ► Model results qualitatively reproduce observed extraction cost dynamics. ► Confirmation of “effective” peak oil, even though resources are in ground.

  17. Applications of supercritical fluid extraction (SFE) of palm oil and oil from natural sources.

    Science.gov (United States)

    Akanda, Mohammed Jahurul Haque; Sarker, Mohammed Zaidul Islam; Ferdosh, Sahena; Manap, Mohd Yazid Abdul; Ab Rahman, Nik Norulaini Nik; Ab Kadir, Mohd Omar

    2012-02-10

    Supercritical fluid extraction (SFE), which has received much interest in its use and further development for industrial applications, is a method that offers some advantages over conventional methods, especially for the palm oil industry. SC-CO₂ refers to supercritical fluid extraction (SFE) that uses carbon dioxide (CO₂) as a solvent which is a nontoxic, inexpensive, nonflammable, and nonpolluting supercritical fluid solvent for the extraction of natural products. Almost 100% oil can be extracted and it is regarded as safe, with organic solvent-free extracts having superior organoleptic profiles. The palm oil industry is one of the major industries in Malaysia that provides a major contribution to the national income. Malaysia is the second largest palm oil and palm kernel oil producer in the World. This paper reviews advances in applications of supercritical carbon dioxide (SC-CO₂) extraction of oils from natural sources, in particular palm oil, minor constituents in palm oil, producing fractionated, refined, bleached, and deodorized palm oil, palm kernel oil and purified fatty acid fractions commendable for downstream uses as in toiletries and confectionaries.

  18. Applications of Supercritical Fluid Extraction (SFE of Palm Oil and Oil from Natural Sources

    Directory of Open Access Journals (Sweden)

    Mohd Omar Ab Kadir

    2012-02-01

    Full Text Available Supercritical fluid extraction (SFE, which has received much interest in its use and further development for industrial applications, is a method that offers some advantages over conventional methods, especially for the palm oil industry. SC-CO2 refers to supercritical fluid extraction (SFE that uses carbon dioxide (CO2 as a solvent which is a nontoxic, inexpensive, nonflammable, and nonpolluting supercritical fluid solvent for the extraction of natural products. Almost 100% oil can be extracted and it is regarded as safe, with organic solvent-free extracts having superior organoleptic profiles. The palm oil industry is one of the major industries in Malaysia that provides a major contribution to the national income. Malaysia is the second largest palm oil and palm kernel oil producer in the World. This paper reviews advances in applications of supercritical carbon dioxide (SC-CO2 extraction of oils from natural sources, in particular palm oil, minor constituents in palm oil, producing fractionated, refined, bleached, and deodorized palm oil, palm kernel oil and purified fatty acid fractions commendable for downstream uses as in toiletries and confectionaries.

  19. Enhancing oil rate in solvent vapour extraction processes through tee-well pattern

    Energy Technology Data Exchange (ETDEWEB)

    Zeng, F.; Knorr, K.D.; Wilton, R.R. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Saskatchewan Research Council, Saskatoon, SK (Canada)

    2008-10-15

    In order for the vapour extraction (VAPEX) process to be considered commercially viable, the production flow rate in classical VAPEX must be increased. The low flow rate can be attributed to the fact that the classical VAPEX process uses forces of buoyancy to distribute the solvent and gravity to drain the diluted oil to the producer. This paper presented a new well pattern, referred to as the tee-SVX process, that may enhance the oil flow rate two to ten times over the classical approach. Additional horizontal injectors, perpendicular to the injector and the producer in classical VAPEX were placed in the top-most region of the reservoir in the new well pattern. The paper described the model development which involved conducting a series of simulation runs in order to evaluate the performance of the new well pattern. The paper also presented a comparison of the performance of the tee-SVX and the classical VAPEX and lateral-SVX. A sensitivity analysis was also performed to further evaluate the performance of tee-SVX and provide the boundaries of the application of the process. Two types of factors affecting the performance of tee-SVX were outlined, notably design factors; and formation and fluid uncertainties. The performance of tee-SVX in thinner reservoirs and in reservoirs with a gas cap were also examined. It was concluded that compared with the lateral-SVX process, the tee-SVX process could significantly reduce the time to solvent breakthrough. 12 refs., 2 tabs., 30 figs.

  20. Bitumen extraction from oil sands ore-water slurry using CaO (lime) and or ozone

    Energy Technology Data Exchange (ETDEWEB)

    Babadagli, T. [Society of Petroleum Engineers, Canadian Section, Calgary, AB (Canada)]|[Alberta Univ., Edmonton, AB (Canada); Burkus, Z.; Moschopedis, S.E.; Ozum, B. [Apex Engineering Inc., Calvert City, KY (United States)

    2008-10-15

    Reductions in the surface and interfacial tensions in oil sands ore-water slurry systems improve bitumen extraction processes from oil sands ore structures and promote the attachment of air bubbles to liberated bitumen droplets. This study provided details of a non-caustic bitumen extraction process where oil sands slurries were conditioned by bitumen asphaltenes modified to act as surfactants. Oil sands ore-water slurry extraction processes were optimized by adding lime (CaO) and oxidizing bitumen asphaltenes with ozone (O{sub 3}). Experiments were conducted using oil sands ore and process water samples from Alberta. Extraction tests were performed to investigate the effects of various CaO and O{sub 3} dosages and treatment retention times on bitumen extraction efficiency on operating temperatures of 20, 35 and 50 degrees C. A Dean-Stark extraction apparatus was used to determine the amount of bitumen contained in the ore, froth, and in left-over tailings. Process water and release water chemistry were also monitored. Bitumen extraction efficiency was defined as the percentage of bitumen recovered in the resulting froth. Use of the slurries allowed high extraction efficiencies at a temperature of 35 degrees C. Energy consumption and carbon dioxide (CO{sub 2}) emissions were also reduced. The study showed that both additions resulted in significant improvements in bitumen extraction efficiency. Use of the technique also eliminated the accumulation of Na{sup +} ions in produced water. It was concluded that further tests are needed in order to commercialize the CaO and O{sub 3} based techniques. 14 refs., 1 tab., 4 figs.

  1. Coconut oil extraction by the Java method: An investigation of its potential application in aqueous Jatropha oil extraction

    NARCIS (Netherlands)

    Marasabessy, A.; Moeis, M.R.; Sanders, J.P.M.; Weusthuis, R.A.

    2010-01-01

    A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w-1 oil from grated

  2. EVALUATION OF THE MICROCLIMATE DURING OLIVE OIL EXTRACTION OPERATIONS INSIDE OLIVE MILLS

    Directory of Open Access Journals (Sweden)

    Vittorio Panaro

    2007-06-01

    Full Text Available Some oil mills, among the most representative in the Puglia Region in terms of quality and productivity have been considered, and the temperature and humidity of the environment and the sensations of temperature felt by the workers were registered inside them during the process of oil extraction. Subsequently, a numerical code in MATLAB language was created, able to calculate the PMV and PPD and a study was carried out of the conditions of global comfort in the environment during the oil extraction process. The results of the surveys carried out in the mills show the importance of microclimate risk analysis in these workplaces, since the instrumental surveys and the calculations have shown that climatic conditions are not comfortable in the olive storage bays. On the other hand, the data from the oil extraction areas shows an acceptable condition of thermal well-being.

  3. Avocado oil extraction processes: method for cold-pressed high-quality edible oil production versus traditional production

    OpenAIRE

    Giacomo Costagli; Matteo Betti

    2015-01-01

    Nowadays the avocado fruit (Persea americana Mill.) is widely regarded as an important fruit for its nutritional values, as it is rich in vital human nutrients. The avocado fruit is mainly sold fresh on the market, which however trades also a relevant quantity of second-grade fruits with a relatively high oil content. Traditionally, this oil is extracted from dried fruits by means of organic solvents, but a mechanical method is also used in general in locations where drying systems and/or sol...

  4. Tendency of lubricating oil manufacturing process

    Energy Technology Data Exchange (ETDEWEB)

    Seki, Toshio

    1988-09-30

    The manufacturing method of paraffin base oil and the tendency are explained in details. The base oil is distillate of petroleum which is obtained at the high boiling of 400/degree/C or higher. The base oil is made from the distillate which is obtained through solvent deasphalting of the vacuum distillated residual oil. The refining process of those material is classified into the two different process steps such as refining and modifying process step in which the quality of the material is improved while eliminating unstable resin, aromatic compound, and sulfur contained in the material, and dewaxing process step in which the wax contained in the material is removed. The former is combination of the two different process steps such as solvent extraction process and hydrogen finishing process or hydroforming process. The latter is a combination of the two different process steps such as solvent dewaxing and catalytic dewaxing (hydro-dewaxing). Various examples of reactions, features and industrial processes are given in accordance with each of these process steps. Regarding the tendency toward the future, the kinds of materials will be expanded in the way that naphthene base oil will adopted as the material oil along with diversification of the quality of lubricating oil, and the processing technology including two-stage processing, catalytic dewaxing, etc. will be expected to be improved. 18 references, 11 figures, 7 tables.

  5. Applications of Enzymes in Oil and Oilseed Processing

    DEFF Research Database (Denmark)

    Xu, Xuebing

    Enzymes, through the last 20-30 years research and development, have been widely explored for the uses in oil and oilseed processing. Following the conventional processing technology from oilseeds, the oil can be produced through pressing or solvent extraction. The crude oil is then refined to meet...... edible requirements. The oil can be also modified to meet functional or even nutritional needs. In each of those steps, enzymes have been used in industry successfully. For the oil processing stage, enzymes have been used to destroy the cell structure so that makes the oil release easier, where...... conventionally high temperature conditioning or cooking is necessary. The good story in industry is the fish oil and olive oil processing. Good quality and higher oil yield have been achieved through the use of enzymes in the processing stages. For the refining stage, the use of enzymes for degumming has...

  6. A simple model for super critical fluid extraction of bio oils from biomass

    International Nuclear Information System (INIS)

    Patel, Rajesh N.; Bandyopadhyay, Santanu; Ganesh, Anuradda

    2011-01-01

    A simple mathematical model to characterize the supercritical extraction process has been proposed in this paper. This model is primarily based on two mass transfer mechanisms: solubility and diffusion. The model assumes two districts mode of extraction: initial constant rate extraction that is controlled by solubility and falling rate extraction that is controlled by diffusivity. Effects of extraction parameters such as pressure and temperature on the extraction of oil have also been studied. The proposed model, when compared with existing models, shows better agreement with the experimental results. The proposed model developed has been applied for both high initial oil content material (cashew nut shells) and low initial oil content material (black pepper).

  7. Lipid Composition of Oil Extracted from Wasted Norway Lobster (Nephrops norvegicus Heads and Comparison with Oil Extracted from Antarctic Krill (Euphasia superba

    Directory of Open Access Journals (Sweden)

    Amaya Albalat

    2016-12-01

    Full Text Available In the UK, the Norway lobster (Nephrops norvegicus supports its most important shellfish fishery. Nephrops are sold either whole, or as “tails-only” for the scampi trade. In the “tailing” process, the “head” (cephalothorax is discarded as waste. A smaller crustacean species, the Antarctic krill Euphasia superba, represents an economically valuable industry, as its extractable oil is sold as a human dietary supplement. The aim of this study was to determine the amount and composition of the oil contained in discarded Nephrops heads and to compare its composition to the oil extracted from krill. Differences due to Geographical variation and seasonal patterns in the amount and composition of lipid were also noted. Results indicated that Nephrops head waste samples collected from more southern locations in Scotland (Clyde Sea area contained higher levels of oil when compared to samples collected from northern locations in Iceland. Moreover, seasonal differences within the Clyde Sea area in Scotland were also observed, with oil extracted from Nephrops head waste peaking at around 11.5% during the summer months when larger and more mature females were caught by trawl. At this time of the year, the valuable fatty acids eicosapentaenoic acid (EPA and docosahexaenoic acid (DHA accounted for around 23% of the total fatty acid content in oil extracted from Nephrops head waste. A seasonal effect on EPA content was found, with higher levels obtained in the summer, while no trend was found in DHA percentages. Finally, oil from Nephrops head waste contained a higher proportion of EPA and DHA than krill oil but these fatty acids were more abundantly linked to the neutral lipids rather to than polar lipids. The characterization of lipid that could be extracted from Nephrops head waste should be seen as a first step for the commercial use of a valuable resource currently wasted. This approach is extremely relevant given the current limited supply of

  8. Optimization of conditions for the extraction of phorbol esters from Jatropha oil

    Energy Technology Data Exchange (ETDEWEB)

    Devappa, Rakshit K.; Makkar, H.P.S.; Becker, K. [Institute for Animal Production in the Tropics and Subtropics (480b), University of Hohenheim, 70593 Stuttgart (Germany)

    2010-08-15

    The production of Jatropha curcas seeds as a biodiesel feedstock is expected to reach 160 Mt by 2017. The present study aims at extracting phorbol esters (PEs) as a co-product from Jatropha oil before processing it to biodiesel. The conditions were optimized for extraction of PEs in organic solvents by using a magnetic stirrer and an Ultra turrax. The extent of reduction in PEs was >99.4% in methanol using any of the stirring tools. However, the extraction using Ultra turrax affected considerably the colour of the remaining oil. Therefore, further solvent:oil ratio, time and temperature were optimized using a magnetic stirrer to get PE rich fraction-I (48.4 mg PEs g{sup -1}) and virtually PE-free oil. PEs were 14 fold higher in this fraction than the control oil. PEs, extracted in methanol from the untreated Jatropha oil, at 1 mg L{sup -1} produced 100% mortality in snails (Physa fontinalis). The methanol extract from virtually PE-free oil when concentrated 20 and 25 time the untreated Jatropha oil (equivalent of 20 mg L{sup -1} and 25 mg L{sup -1} PEs in the control oil) was nontoxic to snails. PE rich fraction-I, obtained as a co-product, can be used in agricultural, medicinal and pharmaceutical applications and the remaining oil can be used for biodiesel preparation. The remaining oil will be friendly to the environment and workers. (author)

  9. Considering extraction constraints in long-term oil price modelling

    Energy Technology Data Exchange (ETDEWEB)

    Rehrl, Tobias; Friedrich, Rainer; Voss, Alfred

    2005-12-15

    Apart from divergence about the remaining global oil resources, the peak oil discussion can be reduced to a dispute about the time rate at which these resources can be supplied. On the one hand it is problematic to project oil supply trends without taking both - prices as well as supply costs - explicitly into account. On the other hand are supply cost estimates however itself heavily dependent on the underlying extraction rates and are actually only valid within a certain business-as-usual extraction rate scenario (which itself is the task to determine). In fact, even after having applied enhanced recovery technologies, the rate at which an oil field can be exploited is quite restricted. Above a certain level an additional extraction rate increase can only be costly achieved at risks of losses in the overall recoverable amounts of the oil reservoir and causes much higher marginal cost. This inflexibility in extraction can be overcome in principle by the access to new oil fields. This indicates why the discovery trend may roughly form the long-term oil production curve, at least for price-taking suppliers. The long term oil discovery trend itself can be described as a logistic process with the two opposed effects of learning and depletion. This leads to the well-known Hubbert curve. Several attempts have been made to incorporate economic variables econometrically into the Hubbert model. With this work we follow a somewhat inverse approach and integrate Hubbert curves in our Long-term Oil Price and EXtraction model LOPEX. In LOPEX we assume that non-OPEC oil production - as long as the oil can be profitably discovered and extracted - is restricted to follow self-regulative discovery trends described by Hubbert curves. Non-OPEC production in LOPEX therefore consists of those Hubbert cycles that are profitable, depending on supply cost and price. Endogenous and exogenous technical progress is extra integrated in different ways. LOPEX determines extraction and price

  10. Considering extraction constraints in long-term oil price modelling

    International Nuclear Information System (INIS)

    Rehrl, Tobias; Friedrich, Rainer; Voss, Alfred

    2005-01-01

    Apart from divergence about the remaining global oil resources, the peak oil discussion can be reduced to a dispute about the time rate at which these resources can be supplied. On the one hand it is problematic to project oil supply trends without taking both - prices as well as supply costs - explicitly into account. On the other hand are supply cost estimates however itself heavily dependent on the underlying extraction rates and are actually only valid within a certain business-as-usual extraction rate scenario (which itself is the task to determine). In fact, even after having applied enhanced recovery technologies, the rate at which an oil field can be exploited is quite restricted. Above a certain level an additional extraction rate increase can only be costly achieved at risks of losses in the overall recoverable amounts of the oil reservoir and causes much higher marginal cost. This inflexibility in extraction can be overcome in principle by the access to new oil fields. This indicates why the discovery trend may roughly form the long-term oil production curve, at least for price-taking suppliers. The long term oil discovery trend itself can be described as a logistic process with the two opposed effects of learning and depletion. This leads to the well-known Hubbert curve. Several attempts have been made to incorporate economic variables econometrically into the Hubbert model. With this work we follow a somewhat inverse approach and integrate Hubbert curves in our Long-term Oil Price and EXtraction model LOPEX. In LOPEX we assume that non-OPEC oil production - as long as the oil can be profitably discovered and extracted - is restricted to follow self-regulative discovery trends described by Hubbert curves. Non-OPEC production in LOPEX therefore consists of those Hubbert cycles that are profitable, depending on supply cost and price. Endogenous and exogenous technical progress is extra integrated in different ways. LOPEX determines extraction and price

  11. Optimization of oil extraction from waste “Date pits” for biodiesel production

    International Nuclear Information System (INIS)

    Jamil, Farrukh; Al-Muhtaseb, Ala’a H.; Al-Haj, Lamya; Al-Hinai, Mohab A.; Hellier, Paul; Rashid, Umer

    2016-01-01

    Highlights: • Oil extraction from “Date pits” has been optimized first time by using RSM. • Optimized conditions for oil extraction gave oil yield of 16.5%. • “Date pits” oil as non-edible feedstock was transformed to biodiesel. • Biodiesel from “Date pits” oil posses potential fuel properties. - Abstract: Biodiesel produced from non-edible feedstocks is increasingly attractive alternative to both fossil diesels and renewable fuels derived from food crops. Date pits are one such lipid containing feedstock, and are widely available in Oman as a waste stream. This study analyses the effects of soxhlet process parameters (temperature, solvent to seed ratio and time) on the extraction of oils from waste Date pits and the subsequent production of biodiesel from it. The highest yield of oil extracted from the Date pits was 16.5 wt% obtained at a temperature of 70 °C, solvent to seed ratio of 4:1 and extraction duration of 7 h. Gas Chromatography analysis showed that Date pits oil consisted of 54.85% unsaturated fatty acids (UFA). Transesterification of the oil extracted was undertaken at 65 °C, a methanol to oil ratio of 6:1 and a reaction time of 1 h for biodiesel production. Biodiesel produced from the Date pits oil was found to have a cetane number of 58.23, density 870 of kg m"−"3, cloud point of 4 °C, pour point of −1 °C, CFPP of −0.5 °C and kinematic viscosity of 3.97 mm"2 s"−"1 (40 °C). In general, Date pit oil appears to be a potential alternative feedstock for biodiesel production.

  12. Process for separating and recovering oil from oil-sands, etc

    Energy Technology Data Exchange (ETDEWEB)

    Preller, H

    1920-07-14

    A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil shale, and coal is characterized in that the material to be separated feeds, by a self-acting feeding arrangement, to a system with slowly rotating drums alternating in different directions and thereby it is exposed to the action of hot water running opposite to the rotation, direction of the drum, with addition of extraction-medium, so that the light material is washed out and rises to the top. It is carried off, while the heavy material sinks to the bottom and, by bucket-conveyor is removed.

  13. Effects of Extraction Process Parameters on the Quality ...

    African Journals Online (AJOL)

    Akorede

    for the first time the effects of extraction process parameters on the properties of parinari seed oil. The parinari seeds ... soya oil used in the production of alkyd polymer resin, a main ... relatively lower acid value implies better storage and shell life of the oil. ... Little work has been done on parinari oil, the variation in lipid.

  14. Coconut oil extraction by the traditional Java method : An investigation of its potential application in aqueous Jatropha oil extraction

    NARCIS (Netherlands)

    Marasabessy, Ahmad; Moeis, Maelita R.; Sanders, Johan P. M.; Weusthuis, Ruud A.

    A traditional Java method of coconut oil extraction assisted by paddy crabs was investigated to find out if crabs or crab-derived components can be used to extract oil from Jatropha curcas seed kernels. Using the traditional Java method the addition of crab paste liberated 54% w w(-1) oil from

  15. Preliminary study: kinetics of oil extraction from sandalwood by microwave-assisted hydrodistillation

    Science.gov (United States)

    Kusuma, H. S.; Mahfud, M.

    2016-04-01

    Sandalwood and its oil, is one of the oldest known perfume materials and has a long history (more than 4000 years) of use as mentioned in Sanskrit manuscripts. Sandalwood oil plays an important role as an export commodity in many countries and its widely used in the food, perfumery and pharmaceuticals industries. The aim of this study is to know and verify the kinetics and mechanism of microwave-assisted hydrodistillation of sandalwood based on a second-order model. In this study, microwave-assisted hydrodistillation is used to extract essential oils from sandalwood. The extraction was carried out in ten extraction cycles of 15 min to 2.5 hours. The initial extraction rate, the extraction capacity and the second-order extraction rate constant were calculated using the model. Kinetics of oil extraction from sandalwood by microwave-assisted hydrodistillation proved that the extraction process was based on the second-order extraction model as the experimentally done in three different steps. The initial extraction rate, h, was 0.0232 g L-1 min-1, the extraction capacity, C S, was 0.6015 g L-1, the second-order extraction rate constant, k, was 0.0642 L g-1 min-1 and coefficient of determination, R 2, was 0.9597.

  16. Other factors to consider in the formation of chloropropandiol fatty esters in oil processes.

    Science.gov (United States)

    Ramli, Muhamad Roddy; Siew, Wai Lin; Ibrahim, Nuzul Amri; Kuntom, Ainie; Abd Razak, Raznim Arni

    2015-01-01

    This paper examines the processing steps of extracting palm oil from fresh fruit bunches in a way that may impact on the formation of chloropropandiol fatty esters (3-MCPD esters), particularly during refining. Diacylglycerols (DAGs) do not appear to be a critical factor when crude palm oils are extracted from various qualities of fruit bunches. Highly hydrolysed oils, in spite of the high free fatty acid (FFA) contents, did not show exceptionally high DAGs, and the oils did not display a higher formation of 3-MCPD esters upon heat treatment. However, acidity measured in terms of pH appears to have a strong impact on 3-MCPD ester formation in the crude oil when heated at high temperatures. The differences in the extraction process of crude palm oil from current commercial processes and that from a modified experimental process showed clearly the effect of acidity of the oil on the formation of 3-MCPD esters. This paper concludes that the washing or dilution step in palm oil mills removes the acidity of the vegetative materials and that a well-optimised dilution/washing step in the extraction process will play an important role in reducing formation of 3-MCPD esters in crude palm oil upon further heat processing.

  17. Comparative analysis of essential oil composition of Iranian and Indian Nigella sativa L. extracted using supercritical fluid extraction and solvent extraction.

    Science.gov (United States)

    Ghahramanloo, Kourosh Hasanzadeh; Kamalidehghan, Behnam; Akbari Javar, Hamid; Teguh Widodo, Riyanto; Majidzadeh, Keivan; Noordin, Mohamed Ibrahim

    2017-01-01

    The objective of this study was to compare the oil extraction yield and essential oil composition of Indian and Iranian Nigella sativa L. extracted by using Supercritical Fluid Extraction (SFE) and solvent extraction methods. In this study, a gas chromatography equipped with a mass spectrophotometer detector was employed for qualitative analysis of the essential oil composition of Indian and Iranian N. sativa L. The results indicated that the main fatty acid composition identified in the essential oils extracted by using SFE and solvent extraction were linoleic acid (22.4%-61.85%) and oleic acid (1.64%-18.97%). Thymoquinone (0.72%-21.03%) was found to be the major volatile compound in the extracted N. sativa oil. It was observed that the oil extraction efficiency obtained from SFE was significantly ( P essential oil, which is composed of higher linoleic acid and thymoquinone contents compared to the essential oil obtained by the solvent extraction technique.

  18. Effect of process variables on the oil extraction from passion fruit seeds by conventional and non-conventional techniques - doi: 10.4025/actascitechnol.v36i1.15217

    Directory of Open Access Journals (Sweden)

    Ricardo Cardoso de Oliveira

    2014-01-01

    Full Text Available The effects of process variables on the oil extraction from passion fruit seeds by three techniques, ultrasound shaker, and soxhlet, and of environment-friendly solvents are evaluated. Ratio variables of seed weight, solvent volume (R, time of extraction (T, and type of solvent (S were evaluated. The significant variables for oil extraction from passion fruit seeds were R and S by ultrasound and shaker techniques and T for soxhlet extraction. Comparison of the three techniques showed that the soxhlet technique had the highest yield with 65% of total oil in the initial matrix.

  19. Methane gas generation from waste water extraction process of crude palm oil in experimental digesters

    Science.gov (United States)

    Dillon, A.; Penafiel, R.; Garzón, P. V.; Ochoa, V.

    2015-12-01

    Industrial processes to extract crude palm oil, generates large amounts of waste water. High concentrations of COD, ST, SV, NH4 + and low solubility of O2, make the treatment of these effluents starts with anaerobic processes. The anaerobic digestion process has several advantages over aerobic degradation: lower operating costs (not aeration), low sludge production, methane gas generation. The 4 stages of anaerobic digestion are: hydrolysis, acidogenic, acetogenesis and methanogenesis. Through the action of enzymes synthesized by microbial consortia are met. The products of each step to serve as reagents is conducted as follows. The organic load times and cell hydraulic retention, solids content, nutrient availability, pH and temperature are factors that influence directly in biodigesters. The objectives of this presentation is to; characterize the microbial inoculum and water (from palm oil wasted water) to be used in biodigestores, make specific methanogenic activity in bioassays, acclimatize the microorganisms to produce methane gas using basal mineral medium with acetate for the input power, and to determine the production of methane gas digesters high organic load.

  20. Fatty acid composition of maize germ oil from high-oil hybrids wet-milling processing

    Directory of Open Access Journals (Sweden)

    Jovanović Petar Lj.

    2005-01-01

    Full Text Available Maize germ was obtained by wet-milling laboratory processing of domestic high-oil maize hybrids. After separation, the germ was subjected to extraction of maize oil. Fatty acid composition of maize germ oil was determined by gas chromatography. The results showed very high levels of unsaturated fatty acids and a constant sum of oleic and linoleic acids in oils of different maize hybrids.

  1. Microwave-Assisted Extraction of Essential Oil from Eucalyptus: Study of the Effects of Operating Conditions

    Directory of Open Access Journals (Sweden)

    A.A. Saoud

    2006-12-01

    Full Text Available Classical extraction of essential oil such as Soxhlet and steam distillation is still a formidable and time-solvent consuming. Microwave assisted process (MAP is used to accelerate the extraction process of target compounds. It can be used for the extraction of compounds from various plants and animal tissues, or the extraction of undesirable components from raw materials. The investigation of microwave extraction of eucalyptus (globules essential oil using ethanol as solvent was carried out. The influence of material (eucalyptus/solvent (ethanol ratio, required doses of microwave, and time of microwave exposure on extraction efficiency, was studied.

  2. A review of lipid extraction from fish processing by-product for use as a biofuel

    International Nuclear Information System (INIS)

    Adeoti, Ibraheem A.; Hawboldt, Kelly

    2014-01-01

    Fish processing facilities generate a significant amount of fish by-products that could be an important source of energy, food, or industrial feedstock. While fish oil is a natural source of omega-3 polyunsaturated fatty acids (mostly eicosapentaenoic acid (EPA), and docosahexaenoic acid (DHA)) used in nutritional supplements, the ability to extract, refine, and get to market of these oils may be challenging at processing facilities where there is limited infrastructure and plants are remotely located. Under these conditions, extraction of oil from fish by-product for use as an in-house or regional fuel may be both economically and environmentally be a more sustainable approach. Processes to extract and refine fish oil for fuel are less energy intensive than the processes for nutritional quality oils and do not require the stringent product specifications and approval process as in the food and pharmaceutical industry. Unlike food crops, extraction of oil from fish residue does not negatively impact food production. This paper presents an overview of developments made in fish oil extraction methodologies including physical, chemical and biological processes. - Highlights: • We have reviewed various lipid extraction methods from fish residue. • Low grade fish oils for fuel applications can be beneficial to facility and region. • The environmental impacts and safety issues can be reduced using SFE method

  3. The influence of extraction methods on composition and antioxidant properties of rice bran oil

    Directory of Open Access Journals (Sweden)

    Noppawat Pengkumsri

    2015-09-01

    Full Text Available AbstractThe current study was employed to assess the influence of the different extraction methods on total tocols, γ-oryzanol content, and antioxidant properties of Chiang Mai Black rice, Mali Red rice, and Suphanburi-1 Brown rice bran oil. Rice bran oil (RBO was extracted by Hexane, Hot pressed, Cold pressed, and Supercritical Fluid Extraction (SFe methods. High yield of RBO was extracted by hexane and SFe methods. Total and subgroups of tocols, and γ-oryzanol content were determined by HPLC. The hexane extracted sample accounts for high content of γ-oryzanol and tocols. Besides, all of RBO extracts contain a significantly high amount of γ-tocotrienol. In vitro antioxidant assay results indicated that superior quality of oil was recovered by hexane extraction. The temperature in the extraction process also affects the value of the oil. Superior quality of oil was recovered by hexane extraction, in terms of phytochemical contents and antioxidant properties compared to other tested extraction methods. Further, thorough study of factors compromising the quality and quantity of RBO recovery is required for the development of enhanced functional foods and other related products.

  4. Mass transfer coefficient in ginger oil extraction by microwave hydrotropic solution

    Science.gov (United States)

    Handayani, Dwi; Ikhsan, Diyono; Yulianto, Mohamad Endy; Dwisukma, Mandy Ayulia

    2015-12-01

    This research aims to obtain mass transfer coefficient data on the extraction of ginger oil using microwave hydrotropic solvent as an alternative to increase zingiberene. The innovation of this study is extraction with microwave heater and hydrotropic solvent,which able to shift the phase equilibrium, and the increasing rate of the extraction process and to improve the content of ginger oil zingiberene. The experiment was conducted at the Laboratory of Separation Techniques at Chemical Engineering Department of Diponegoro University. The research activities carried out in two stages, namely experimental and modeling work. Preparation of the model postulated, then lowered to obtain equations that were tested and validated using data obtained from experimental. Measurement of experimental data was performed using microwave power (300 W), extraction temperature of 90 ° C and the independent variable, i.e.: type of hydrotropic, the volume of solvent and concentration in order, to obtain zingiberen levels as a function of time. Measured data was used as a tool to validate the postulation, in order to obtain validation of models and empirical equations. The results showed that the mass transfer coefficient (Kla) on zingiberene mass transfer models ginger oil extraction at various hydrotropic solution attained more 14 ± 2 Kla value than its reported on the extraction with electric heating. The larger value of Kla, the faster rate of mass transfer on the extraction process. To obtain the same yields, the microwave-assisted extraction required one twelfth time shorter.

  5. Design and construction of a prototype for the continuous extraction of Sacha Inchi seed oil with a cold pressing process

    Directory of Open Access Journals (Sweden)

    Nelson Ramiro Gutiérrez Suquillo

    2017-03-01

    Full Text Available This work presents the design of an oil extractor from the Sacha Inchi seed with an extruder screw mechanism allows a maximum yield of 34% through a continuous cold extraction process at working temperatures below 45 ° C. The temperature is a critical parameter because when it exceeds 50 ° C, the oil decreases its nutritional value by the loss of its most important properties such as: Omega 3 (48%, Omega 6 (36%, Omega 9 (8%, digestibility (96%, vitamin A and E. The methodology used for the development of the work was the concurrent and simultaneous design according to the recommendations of National Instruments. The prototype consists of the extruder screw, pressure chamber, feed chamber, sieve and filter. The advantage of modular design is the flexibility it offers, so that when changing certain components it is possible to use the prototype to extract oil of different types and sizes of seeds. The products obtained from this mechanism are: 33.34% of oil and the solid residue known as Cake in 66.66% which has many applications in the field of human food and pets. Due to the processing of a food product, the requirements of ISO 22005 were applied for the design and implementation of the prototype.

  6. Heat and power demands in babassu palm oil extraction industry in Brazil

    International Nuclear Information System (INIS)

    Teixeira, Marcos A.

    2005-01-01

    The objective of this paper is to analyze the energy use profile of the babassu (Orbignya ssp-Palmae) oil extraction industry in Brazil in order to establish the basis for a cogeneration study of this important part of the Brazilian Northeast region economy, which is still ignored by energetic biomass studies. The work used information from new equipment suppliers that was analyzed against field information from operating units. The data was used to establish a basis for the thermal and mechanical energy consumption for the two main basic unit profiles for the sector: a simple one with just oil extraction and the other, more vertically integrated with other secondary by-products. For the energetic demand taken from the only oil extraction unit profile study, the minimum pressure for the steam process was estimated at 1.4MPa, electric demand at 5.79kW/ton of processed kernel and heat consumption at 2071MJ/ton of processed kernel (829kg steam/ton of processed kernel). For the vertically integrated unit profile, the following values were found: minimum pressure for the steam process 1.4MPa, electric demand 6.22kW/ton of processed kernel and heat consumption 21,503MJ/ton of processed kernel (7600kg steam/ton of processed kernel)

  7. Extraction of heavy oil by supercritical carbon dioxide

    DEFF Research Database (Denmark)

    Rudyk, Svetlana Nikolayevna; Spirov, Pavel; Søgaard, Erik Gydesen

    2010-01-01

    The present study deals with the extraction of heavy oil by supercritical carbon dioxide at the pressure values changing from 16 to 56 MPa at the fixed value of temperature: 60oC. The amount of the recovered liquid phase of oil was calculated as a percentage of the extracted amount to the initial...... 40 gm of oil. The noticeable breackover point in the graph of the oil recovery versus pressure was observed at 27 MPa, which was in concordance with the conclusions from chromatographic analysis of the extracted oil samples. But the recovery rate of 14 % at this pressure value was not high enough...

  8. Extraction by Dry Rendering Methode and Characterization Fish Oil of Catfish (Pangasius hypopthalmus Viscera Fat by Product of Smooked Fish Processing

    Directory of Open Access Journals (Sweden)

    Kamini Kamini

    2016-12-01

    Full Text Available The catfish viscera fat, is cathfish processing by-products, has potential to be used as a source ofraw material for production of fish oil. This study aimed to analyze the value of proximate, heavy metalcontent and fatty acid profile of catfish viscera fat (Pangasius hypopthalmus and characterized fish oilextracted by dry rendering in various temperature and time than compared it to fish oil extracted by stoveheating to obtain the best treatment. Proximate, heavy metal residue, and the fatty acid profile analysiswere conducted for characterizing catfish viscera fat. Fish oil extraction was conducted by dry renderingin various temperatures of 50, 60, 70, 80 °C for 1, 2, and 3 hours. Fish oil quality was determined by thechemical characteristics i.e. PV, FFA, anisidin and TOTOX. The results of the study showed that fat contentof catfish fat viscera was 88.19 %, the heavy metals content was below SNI standart to be consumed, and fattyacid profile composition was SFA>MUFA>PUFA. The highest fatty acid content was oleic acid. The best fishoil quality was resulted on temperature extraction of 50°C for 2 hours with yield value, PV, FFA, anisidin,and TOTOX were 45.17 %, 2.77 meq/kg, 0.83 %, 2.86 meq/kg, 8.39 meq/kg respectively. This result was notsignificantly different with fish oil extracted by the stove heating expect for yield and PV were 80.11% and6.52 meq/kg, respectively.

  9. Extraction and characterization of Raphanus Sativus seed oil ...

    African Journals Online (AJOL)

    properties and bioactive ingredients of Raphanus sativus seed oil. Methods: Raphanus sativus seed oil was prepared by traditional solvent extraction (SE), super-critical carbon dioxide extraction (SCE) and sub-critical propane extraction (SPE). The yield, physicochemical properties, fatty acid composition and oxidative ...

  10. Characterization of grape seed and pomace oil extracts

    Directory of Open Access Journals (Sweden)

    Sema Çetin, Emine

    2007-03-01

    Full Text Available The objective of this study was to determine the nutrient and antioxidant contents of grape seed and pomace oil extracts from the main Turkish wine grape cultivars, Kalecik karas1, Narince, Hasandede and Emir. Dried and powdered seed and pomace materials were extracted with hexane. The results showed that the oil concentration of seeds ranged from 12.35 to 16.00% while in pomace the oil concentration varied from 5.47 to 8.66%. Grape seed and pomace oils were rich in oleic and linoleic acids and the degree of unsaturation in the oils was over 85%. α- tocopherol was the most abundant tocopherol in the oil extracts. Although γ and δ-tocopherols were found with low concentrations, β-tocopherol was not detected in the oil extracts. Oil extracts from pomace in all cultivars gave the highest tocopherol contents compared to the seeds. The contents of total phenolics were higher in pomace oil extracts than seed oil extracts. The highest total phenolic content (392.74 mg/kg was found in the oil extract from Narince pomace compared to the other oil extracts. The refractive indexes of pomace oil extracts ranged from 1.445 to 1.468 while the refractive indexes of the seed oil extracts ranged from 1.460 and 1.466. In conclusion, wine byproducts including the seeds and pomace can be utilized both to get natural antioxidants and to obtain edible vegetable oil.El objetivo de este estudio fue determinar los contenidos de nutrientes y antioxidantes de extractos de aceite de orujo y pepita de uva de los principales cultivares de uva de Turquía, Kalecik karas1, Narince, Hasandede y Emir. El material procedente del orujo y las semillas, seco y pulverizado, se extrajo con hexano. Los resultados mostraron que la concentración de aceite de las semillas osciló entre 12,35 y 16,00 % mientras que en el aceite de orujo la concentración varió entre 5,47 y 8,66%. Los aceites de orujo y pepita de uva eran ricos en ácido oleico y linoleico y su grado de instauraci

  11. Aggressive oil extraction and precautionary saving: Coping with volatility

    NARCIS (Netherlands)

    van der Ploeg, F.

    2010-01-01

    The effects of stochastic oil demand on optimal oil extraction paths and tax, spending and government debt policies are analyzed when the oil demand schedule is linear and preferences quadratic. Without prudence, optimal oil extraction is governed by the Hotelling rule and optimal budgetary policies

  12. Recovery of Oil with Unsaturated Fatty Acids and Polyphenols from Chaenomelessinensis (Thouin Koehne: Process Optimization of Pilot-Scale Subcritical Fluid Assisted Extraction

    Directory of Open Access Journals (Sweden)

    Zhenzhou Zhu

    2017-10-01

    Full Text Available The potential effects of three modern extraction technologies (cold-pressing, microwaves and subcritical fluids on the recovery of oil from Chaenomelessinensis (Thouin Koehne seeds have been evaluated and compared to those of conventional chemical extraction methods (Soxhlet extraction. This oil contains unsaturated fatty acids and polyphenols. Subcritical fluid extraction (SbFE provided the highest yield—25.79 g oil/100 g dry seeds—of the three methods. Moreover, the fatty acid composition in the oil samples was analysed using gas chromatography–mass spectrometry. This analysis showed that the percentages of monounsaturated (46.61%, and polyunsaturated fatty acids (42.14%, after applying SbFE were higher than those obtained by Soxhlet, cold-pressing or microwave-assisted extraction. In addition, the oil obtained under optimized SbFE conditions (35 min extraction at 35 °C with four extraction cycles, showed significant polyphenol (527.36 mg GAE/kg oil, and flavonoid (15.32 mg RE/kg oil, content, had a good appearance and was of high quality.

  13. Recovery of Oil with Unsaturated Fatty Acids and Polyphenols from Chaenomelessinensis (Thouin) Koehne: Process Optimization of Pilot-Scale Subcritical Fluid Assisted Extraction.

    Science.gov (United States)

    Zhu, Zhenzhou; Zhang, Rui; Zhan, Shaoying; He, Jingren; Barba, Francisco J; Cravotto, Giancarlo; Wu, Weizhong; Li, Shuyi

    2017-10-22

    The potential effects of three modern extraction technologies (cold-pressing, microwaves and subcritical fluids) on the recovery of oil from Chaenomelessinensis (Thouin) Koehne seeds have been evaluated and compared to those of conventional chemical extraction methods (Soxhlet extraction). This oil contains unsaturated fatty acids and polyphenols. Subcritical fluid extraction (SbFE) provided the highest yield-25.79 g oil/100 g dry seeds-of the three methods. Moreover, the fatty acid composition in the oil samples was analysed using gas chromatography-mass spectrometry. This analysis showed that the percentages of monounsaturated (46.61%), and polyunsaturated fatty acids (42.14%), after applying SbFE were higher than those obtained by Soxhlet, cold-pressing or microwave-assisted extraction. In addition, the oil obtained under optimized SbFE conditions (35 min extraction at 35 °C with four extraction cycles), showed significant polyphenol (527.36 mg GAE/kg oil), and flavonoid (15.32 mg RE/kg oil), content, had a good appearance and was of high quality.

  14. Parameters Affecting the Extraction Process of Jatropha Curcas Oil Using a Single Screw Extruder

    OpenAIRE

    Siregar, Ali Nurrakhmad; Ghani, Jaharah A; Che Haron, Che Hassan; Rizal, Muhammad

    2015-01-01

    The most commonly used technique to separate oil and cake from J. curcas seeds is mechanical extraction. It uses simple tools such as a piston and a screw extruder to produce high pressure, driven by hand or by engine. A single screw extruder has one screw rotating inside the barrel and materials simultaneously flow from the feed to the die zone. The highest oil yield can be obtained by a well-designed oil press as well as finding the optimum conditions for all parameters involved during the ...

  15. Oil Extraction and Indigenous Livelihoods in the Northern Ecuadorian Amazon.

    Science.gov (United States)

    Bozigar, Matthew; Gray, Clark L; Bilsborrow, Richard E

    2016-02-01

    Globally, the extraction of minerals and fossil fuels is increasingly penetrating into isolated regions inhabited by indigenous peoples, potentially undermining their livelihoods and well-being. To provide new insight to this issue, we draw on a unique longitudinal dataset collected in the Ecuadorian Amazon over an 11-year period from 484 indigenous households with varying degrees of exposure to oil extraction. Fixed and random effects regression models of the consequences of oil activities for livelihood outcomes reveal mixed and multidimensional effects. These results challenge common assumptions about these processes and are only partly consistent with hypotheses drawn from the Dutch disease literature.

  16. Identification of components contents of oil extracts and its aromatic fractions. Extracted from oil-polluted soils of Surakhany oilfield of Apsheron peninsula

    International Nuclear Information System (INIS)

    Abbasova, D.R.; Kerimov, M.K.; Cafarova, R.A.

    2010-01-01

    In this work have been studied components content of oil extracts and its aromatic fraction of Surakhany oilfield by DSC and TGA in follow temperature interval 20-500 degrees Celsium. Have been identified that low paraffinicity of oil fraction and oil extract and its aromatic fraction in this investigation show to young geological age (low transformation) of this oil.

  17. Extraction and characterization of radish seed oils using different ...

    African Journals Online (AJOL)

    Purpose: To evaluate the impact of three different extraction methods on oil yield, physicochemical properties and bioactive ingredients of radish seeds. Methods: Radish seed oil was prepared by traditional solvent extraction (SE), supercritical carbon dioxide extraction (SCE) and sub-critical propane extraction (SPE).

  18. Distribution of clay minerals in the process streams produced by the extraction of bitumen from Athabasca oil sands

    Energy Technology Data Exchange (ETDEWEB)

    Kaminsky, H.A.W.; Etsell, T.H.; Ivey, D.G. [Alberta Univ., Edmonton, AB (Canada). Dept. of Chemical and Materials Engineering; Omotoso, O. [Natural Resources Canada, Devon, AB (Canada). CETC

    2009-02-15

    The clay minerals present in the oil sands were studied with particular reference to how they are partitioned in bitumen ore during the extraction process. Bitumen production from surface-mined oil sands accounts for nearly two-thirds of the total bitumen production in Alberta. Every cubic meter of mined ore results in 1.3 cubic meters of mature fine tailings (MFT). The characteristic differences between the clay minerals that report to the froth versus the tailings streams were also examined to determine which minerals could impact different unit operations in the bitumen extraction process. X-ray diffraction and random powder samples were used to quantify the clay minerals. Particle size distribution and clay activity balances were also conducted. The degree of partitioning during the conditioning and flotation stages in a batch extractor was determined by the surface properties of the clay minerals. The water-continuous tailings stream was separated into fine and coarse tailings fractions through sedimentation. The study showed that bitumen-clay interactions may be dominated by kaolinite or iron oxides. Clays are responsible for the poor settling behaviour of MFTs. The clay minerals present in the oil sands include illite, illite-smectite, kaolinite, kaolinite-smectite, and chlorite. The close proximity of the tailings ponds to the Athabasca River and volatile organic compounds (VOCs) emission require that the ponds be reclaimed to a natural landscape before mine closure. In addition to its impact on fine tailings reclamation, clay mineralogy plays a role in extraction froth flotation and emulsion stability during froth treatment. The mineralogy of the froth solids was found to be different from the mineralogy of the middlings and tailings solids. 39 refs., 6 tabs., 6 figs.

  19. Calendula oil processing : seed classification, oil extraction, refining process development and oil quality aspects

    NARCIS (Netherlands)

    Janssens, R.J.J.

    2000-01-01

    The difference in Calendula oil quality from fractions obtained after seed classification is enormous. The oil quality varies from excellent to very poor, according to important aspects such as in the hulls and dust fraction, high free fatty acid values (13% vs. 0.6%) are found. This can be

  20. Extraction of citronella (Cymbopogon nardus essential oil using supercritical co2: experimental data and mathematical modeling

    Directory of Open Access Journals (Sweden)

    C. F. Silva

    2011-06-01

    Full Text Available Citronella essential oil has more than eighty components, of which the most important ones are citronellal, geranial and limonene. They are present at high concentrations in the oil and are responsible for the repellent properties of the oil. The oil was extracted using supercritical carbon dioxide due to the high selectivity of the solvent. The operational conditions studied varied from 313.15 to 353.15 K for the temperature and the applied pressures were 6.2, 10.0, 15.0 and 180.0 MPa. Better values of efficiency of the extracted oil were obtained at higher pressure conditions. At constant temperature, the amount of extracted oil increased when the pressure increased, but the opposite occurred when the temperature increased at constant pressure. The composition of the essential oil was complex, although there were several main components in the oil and some waxes were presented in the extracted oils above 10.0 MPa. The results were modeled using a mathematical model in a predictive way, reproducing the extraction curves over the maximum time of the process.

  1. Comparative analysis of essential oil composition of Iranian and Indian Nigella sativa L. extracted using supercritical fluid extraction and solvent extraction

    Directory of Open Access Journals (Sweden)

    Ghahramanloo KH

    2017-07-01

    Full Text Available Kourosh Hasanzadeh Ghahramanloo,1 Behnam Kamalidehghan,2 Hamid Akbari Javar,3 Riyanto Teguh Widodo,1 Keivan Majidzadeh,4 Mohamed Ibrahim Noordin1 1Department of Pharmacy, Faculty of Medicine, University of Malaya, Kuala Lumpur, Malaysia; 2Medical Genetics Department, National Institute of Genetic Engineering and Biotechnology (NIGEB, 3Department of Pharmaceutics, Faculty of Pharmacy, Tehran University of Medical Sciences (TUMS, 4Breast Cancer Research Center (BCRC Academic Center for Education, Culture and Research, Tehran, Iran Abstract: The objective of this study was to compare the oil extraction yield and essential oil composition of Indian and Iranian Nigella sativa L. extracted by using Supercritical Fluid Extraction (SFE and solvent extraction methods. In this study, a gas chromatography equipped with a mass spectrophotometer detector was employed for qualitative analysis of the essential oil composition of Indian and Iranian N. sativa L. The results indicated that the main fatty acid composition identified in the essential oils extracted by using SFE and solvent extraction were linoleic acid (22.4%–61.85% and oleic acid (1.64%–18.97%. Thymoquinone (0.72%–21.03% was found to be the major volatile compound in the extracted N. sativa oil. It was observed that the oil extraction efficiency obtained from SFE was significantly (P<0.05 higher than that achieved by the solvent extraction technique. The present study showed that SFE can be used as a more efficient technique for extraction of N. Sativa L. essential oil, which is composed of higher linoleic acid and thymoquinone contents compared to the essential oil obtained by the solvent extraction technique. Keywords: Nigella sativa L., essential oil extraction, supercritical fluid extraction, solvent extraction, fatty acid composition, thymoquinone, linoleic acid

  2. Supercritical solvent extraction of oil sand bitumen

    Science.gov (United States)

    Imanbayev, Ye. I.; Ongarbayev, Ye. K.; Tileuberdi, Ye.; Mansurov, Z. A.; Golovko, A. K.; Rudyk, S.

    2017-08-01

    The supercritical solvent extraction of bitumen from oil sand studied with organic solvents. The experiments were performed in autoclave reactor at temperature above 255 °C and pressure 29 atm with stirring for 6 h. The reaction resulted in the formation of coke products with mineral part of oil sands. The remaining products separated into SARA fractions. The properties of the obtained products were studied. The supercritical solvent extraction significantly upgraded extracted natural bitumen.

  3. Cogeneration of biodiesel and nontoxic cottonseed meal from cottonseed processed by two-phase solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Qian Junfeng, E-mail: qianjunfeng80@126.co [Jiangsu Provincial Key Laboratory of Fine Petrochemical Engineering, Jiangsu Polytechnic University, Changzhou 213016 (China) and College of Chemistry and Chemical Engineering, Nanjing University of Technology, Nanjing 210009 (China); Yun Zhi; Shi Haixian [College of Chemistry and Chemical Engineering, Nanjing University of Technology, Nanjing 210009 (China)

    2010-12-15

    In the present work, the preparation of biodiesel from cottonseed oil produced by two-phase solvent extraction (TSE) was studied. The experimental results of TSE process of cottonseed showed that the optimal extraction conditions were 30 g samples, 240 mL extraction solvent mixture and methanol/petroleum ether volume ratio 60:40, extraction temperature 30 deg. C, extraction time 30 min. Under the extraction conditions, the extraction rate of cottonseed oil could achieve 98.3%, the free fatty acid (FFA) and water contents of cottonseed oil were reduced to 0.20% and 0.037%, respectively, which met the requirement of alkali-catalyzed transesterification. The free gossypol (FG) content in cottonseed meal produced from two-phase solvent extraction could reduce to 0.014% which was far below the FAO standard. And the nontoxic cottonseed meal could be used as animal protein feed resources. After the TSE process of cottonseed, the investigations were carried out on transesterification of methanol with oil-petroleum ether solution coming from TSE process in the presence of sodium hydroxide (CaO) as the solid base catalyst. The influences of weight ratio of petroleum ether to cottonseed oil, reaction temperature, molar ratio of methanol to oil, alkali catalyst amount and reaction time on cottonseed oil conversion were respectively investigated by mono-factor experiments. The conversion of cottonseed oil into fatty acid methyl ester (FAME) could achieve 98.6% with 3:1 petroleum ether/oil weight ratio, 65 deg. C reaction temperature, 9:1 methanol/oil mole ratio, 4% (catalyst/oil weight ratio, w/w) solid base catalyst amount and 3 h reaction time. The properties of FAME product prepared from cottonseed oil produced by two-phase solvent extraction met the ASTM specifications for biodiesel.

  4. Cogeneration of biodiesel and nontoxic cottonseed meal from cottonseed processed by two-phase solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Qian, Junfeng [Jiangsu Provincial Key Laboratory of Fine Petrochemical Engineering, Jiangsu Polytechnic University, Changzhou 213016 (China); College of Chemistry and Chemical Engineering, Nanjing University of Technology, Nanjing 210009 (China); Yun, Zhi; Shi, Haixian [College of Chemistry and Chemical Engineering, Nanjing University of Technology, Nanjing 210009 (China)

    2010-12-15

    In the present work, the preparation of biodiesel from cottonseed oil produced by two-phase solvent extraction (TSE) was studied. The experimental results of TSE process of cottonseed showed that the optimal extraction conditions were 30 g samples, 240 mL extraction solvent mixture and methanol/petroleum ether volume ratio 60:40, extraction temperature 30 C, extraction time 30 min. Under the extraction conditions, the extraction rate of cottonseed oil could achieve 98.3%, the free fatty acid (FFA) and water contents of cottonseed oil were reduced to 0.20% and 0.037%, respectively, which met the requirement of alkali-catalyzed transesterification. The free gossypol (FG) content in cottonseed meal produced from two-phase solvent extraction could reduce to 0.014% which was far below the FAO standard. And the nontoxic cottonseed meal could be used as animal protein feed resources. After the TSE process of cottonseed, the investigations were carried out on transesterification of methanol with oil-petroleum ether solution coming from TSE process in the presence of sodium hydroxide (CaO) as the solid base catalyst. The influences of weight ratio of petroleum ether to cottonseed oil, reaction temperature, molar ratio of methanol to oil, alkali catalyst amount and reaction time on cottonseed oil conversion were respectively investigated by mono-factor experiments. The conversion of cottonseed oil into fatty acid methyl ester (FAME) could achieve 98.6% with 3:1 petroleum ether/oil weight ratio, 65 C reaction temperature, 9:1 methanol/oil mole ratio, 4% (catalyst/oil weight ratio, w/w) solid base catalyst amount and 3 h reaction time. The properties of FAME product prepared from cottonseed oil produced by two-phase solvent extraction met the ASTM specifications for biodiesel. (author)

  5. Desulfurization of AL-Ahdab Crude Oil using Oxidative Processes

    OpenAIRE

    Neran Khalel Ibrahim; Saja Mohsen Jabbar

    2015-01-01

    Two different oxidative desulfurization strategies based on oxidation/adsorption or oxidation/extraction were evaluated for the desulfurization of AL-Ahdab (AHD) sour crude oil (3.9wt% sulfur content). In the oxidation process, a homogenous oxidizing agent comprising of hydrogen peroxide and formic acid was used. Activated carbons were used as sorbent/catalyst in the oxidation/adsorption process while acetonitrile was used as an extraction solvent in the oxidation/extraction process. For the ...

  6. Factors affecting emulsion stability and quality of oil recovered from enzyme-assisted aqueous extraction of soybeans.

    Science.gov (United States)

    Jung, S; Maurer, D; Johnson, L A

    2009-11-01

    The objectives of the present study were to assess how the stability of the emulsion recovered from aqueous extraction processing of soybeans was affected by characteristics of the starting material and extraction and demulsification conditions. Adding endopeptidase Protex 6L during enzyme-assisted aqueous extraction processing (EAEP) of extruded soybean flakes was vital to obtaining emulsions that were easily demulsified with enzymes. Adding salt (up to 1.5 mM NaCl or MgCl(2)) during extraction and storing extruded flakes before extraction at 4 and 30 degrees C for up to 3 months did not affect the stabilities of emulsions recovered from EAEP of soy flour, flakes and extruded flakes. After demulsification, highest free oil yield was obtained with EAEP of extruded flakes, followed by flour and then flakes. The same protease used for the extraction step was used to demulsify the EAEP cream emulsion from extruded full-fat soy flakes at concentrations ranging from 0.03% to 2.50% w/w, incubation times ranging from 2 to 90 min, and temperatures of 25, 50 or 65 degrees C. Highest free oil recoveries were achieved at high enzyme concentrations, mild temperatures, and short incubation times. Both the nature of enzyme (i.e., protease and phospholipase), added alone or as a cocktail, concentration of enzymes (0.5% vs. 2.5%) and incubation time (1 vs. 3 h), use during the extraction step, and nature of enzyme added for demulsifying affected free oil yield. The free oil recovered from EAEP of extruded flakes contained less phosphorus compared with conventional hexane-extracted oil. The present study identified conditions rendering the emulsion less stable, which is critical to increasing free oil yield recovered during EAEP of soybeans, an environmentally friendly alternative processing method to hexane extraction.

  7. Statistical model of planning technological indicators for oil extraction

    Energy Technology Data Exchange (ETDEWEB)

    Galeyev, R G; Lavushchenko, V P; Sheshnev, A S

    1979-01-01

    The efficiency of the process of oil extraction is determined by the effect of a number of interrelated technological indicators. Analytical expression of the interrelationships of the indicators was represented by an econometric model consisting of a system of linear regression equations. The basic advantage of these models is the possibility of calculating in them different, significantly important interrelationships. This makes it possible to correlate all calculations into a single logically noncontradictory balanced system. The developed model of the technological process of oil extraction makes it possible to significantly facilitate calculation and planning of its basic indicators with regard for system and balance requirements, makes it possible to purposefully generate new variants. In this case because of the optimal distribution of the volumes of geological-technical measures, a decrease in the total outlays for their implementation is achieved. Thus for the Berezovskiy field, this saving was R 150,000.

  8. Supercritical carbon dioxide (SC-CO2) extraction of essential oil from Swietenia mahagoni seeds

    Science.gov (United States)

    Norodin, N. S. M.; Salleh, L. M.; Hartati; Mustafa, N. M.

    2016-11-01

    Swietenia mahagoni (Mahogany) is a traditional plant that is rich with bioactive compounds. In this study, process parameters such as particle size, extraction time, solvent flowrate, temperature and pressure were studied on the extraction of essential oil from Swietenia mahagoni seeds by using supercritical carbon dioxide (SC-CO2) extraction. Swietenia mahagoni seeds was extracted at a pressure of 20-30 MPa and a temperature of 40-60°C. The effect of particle size on overall extraction of essential oil was done at 30 MPa and 50°C while the extraction time of essential oil at various temperatures and at a constant pressure of 30 MPa was studied. Meanwhile, the effect of flowrate CO2 was determined at the flowrate of 2, 3 and 4 ml/min. From the experimental data, the extraction time of 120 minutes, particle size of 0.5 mm, the flowrate of CO2 of 4 ml/min, at a pressure of 30 MPa and the temperature of 60°C were the best conditions to obtain the highest yield of essential oil.

  9. Biological Properties of Fucoxanthin in Oil Recovered from Two Brown Seaweeds Using Supercritical CO2 Extraction

    Directory of Open Access Journals (Sweden)

    Saravana Periaswamy Sivagnanam

    2015-05-01

    Full Text Available The bioactive materials in brown seaweeds hold great interest for developing new drugs and healthy foods. The oil content in brown seaweeds (Saccharina japonica and Sargassum horneri was extracted by using environmentally friendly supercritical CO2 (SC-CO2 with ethanol as a co-solvent in a semi-batch flow extraction process and compared the results with a conventional extraction process using hexane, ethanol, and acetone mixed with methanol (1:1, v/v. The SC-CO2 method was used at a temperature of 45 °C and pressure of 250 bar. The flow rate of CO2 (27 g/min was constant for the entire extraction period of 2 h. The obtained oil from the brown seaweeds was analyzed to determine their valuable compounds such as fatty acids, phenolic compounds, fucoxanthin and biological properties including antioxidant, antimicrobial, and antihypertension effects. The amounts of fucoxanthin extracted from the SC-CO2 oils of S. japonica and S. horneri were 0.41 ± 0.05 and 0.77 ± 0.07 mg/g, respectively. High antihypertensive activity was detected when using mixed acetone and methanol, whereas the phenolic content and antioxidant property were higher in the oil extracted by SC-CO2. The acetone–methanol mix extracts exhibited better antimicrobial activities than those obtained by other means. Thus, the SC-CO2 extraction process appears to be a good method for obtaining valuable compounds from both brown seaweeds, and showed stronger biological activity than that obtained by the conventional extraction process.

  10. Biological Properties of Fucoxanthin in Oil Recovered from Two Brown Seaweeds Using Supercritical CO2 Extraction.

    Science.gov (United States)

    Sivagnanam, Saravana Periaswamy; Yin, Shipeng; Choi, Jae Hyung; Park, Yong Beom; Woo, Hee Chul; Chun, Byung Soo

    2015-05-29

    The bioactive materials in brown seaweeds hold great interest for developing new drugs and healthy foods. The oil content in brown seaweeds (Saccharina japonica and Sargassum horneri) was extracted by using environmentally friendly supercritical CO2 (SC-CO2) with ethanol as a co-solvent in a semi-batch flow extraction process and compared the results with a conventional extraction process using hexane, ethanol, and acetone mixed with methanol (1:1, v/v). The SC-CO2 method was used at a temperature of 45 °C and pressure of 250 bar. The flow rate of CO2 (27 g/min) was constant for the entire extraction period of 2 h. The obtained oil from the brown seaweeds was analyzed to determine their valuable compounds such as fatty acids, phenolic compounds, fucoxanthin and biological properties including antioxidant, antimicrobial, and antihypertension effects. The amounts of fucoxanthin extracted from the SC-CO2 oils of S. japonica and S. horneri were 0.41 ± 0.05 and 0.77 ± 0.07 mg/g, respectively. High antihypertensive activity was detected when using mixed acetone and methanol, whereas the phenolic content and antioxidant property were higher in the oil extracted by SC-CO2. The acetone-methanol mix extracts exhibited better antimicrobial activities than those obtained by other means. Thus, the SC-CO2 extraction process appears to be a good method for obtaining valuable compounds from both brown seaweeds, and showed stronger biological activity than that obtained by the conventional extraction process.

  11. Effect of Grape Seeds Oil Extracted from Radiation Processed Seeds on Lipid Metabolism and on Antioxidant Activity in Rats Fed Diets Containing Cholesterol

    International Nuclear Information System (INIS)

    El-Neily, H.F.G.; El-Shennawy, H.M.

    2011-01-01

    Grape seeds were separated from fresh grape pomace and dried at room temperature then packed in polyethylene bags and subjected to gamma rays at dose level of 10 kGy. The grape seeds oil was extracted from non and irradiated seeds. The oil quality, fatty acid composition and total phenolic compounds of oil extracted from non or irradiated seeds have been studied. The results indicated that there were significant increases in the acid value, saponification value and peroxide value of oil extracted from irradiated seeds at 10 kGy by 46.2%, 2.5% and 95.2%, respectively, and the total phenolic compounds and total radical trapping antioxidant potential (TRAP) were reduced by 22.13% and 10%, respectively, as compared to those of oil extracted from non-irradiated seeds. No degradation of the fatty acids; palmitic, linoleic, linolenic and arachidic acids, were observed for oil extracted from irradiated seeds at 10 kGy. However, significant decrease in oleic acid by 11.35% and increase in stearic acid by 26.22% were recorded corresponding to those for oil extracted from non-irradiated seeds. The effect of grape seeds oils extracted from non or irradiated seeds on lipid metabolism and antioxidant activity was investigated using 60 male Albino rats divided into six groups: (1) Control group: animals fed casein diet. (2) Ch group: animals received casein diet contains 10 g cholesterol per kg diet. (3) RGSO group: animals received diet contains grape seeds oil extracted from non-irradiated seeds (100 g oil per kg diet). (4) RGSO + Ch group: rats received diet contains grape seeds oil extracted from non-irradiated seeds (100 g oil per kg diet) + 100 g cholesterol per kg diet. (5) IGSO group: rats received diet contains grape seeds oil extracted from irradiated seeds at 10 kGy (100 g oil per kg diet). (6) IGSO + Ch group: rats received diet contains grape seeds oil extracted from irradiated seeds at 10 kGy (100 g oil per kg diet) + 10 g cholesterol per kg diet. Animals received

  12. Optimization of processing parameters for extraction of essential oil from Foeniculum vulgare

    Directory of Open Access Journals (Sweden)

    2017-11-01

    Full Text Available Background and objectives: It is necessary to specify the best conditions of essential oils production to get more major compound(s and higher yield oil. The fennel oil is useful in pharmaceutical industry as flavor. The main component of fennel oil is anethole (55-75%. The objective of this work was to identify the effect of  particle size, pH of water, method of distillation and using ultrasound on extraction of fennel essential oil (and its major constituent, anethole. Methods: We used a statistical method called D-optimal Design that appointed pH, particle size and method for each assay. Fennel seeds were purchased, then milled and passed from different meshes. In the first series, the seeds powder was distilled directly. In the second series the seeds were placed in an ultrasonic apparatus for 30 min. The essential oils were subsequently isolated by two methods, hydro distillation and steam distillation, in different sizes (25, 30, 40, 50 and pH (5.5, 5.8, 7, 7.4, 8.5. Fifty g of dry seeds were used in each distillation (for 3 h. Analytical gas chromatography (GC was used to determine the essential oil composition. Results: In the steam distillation, the volume of essential oils and the concentration of anethole, whatever the plant became smaller, was less. However, in the water distillation, it was more and by comparing the two steps, without and with ultrasound, it increased 20% after the ultrasound. Conclusion: optimum conditions according to the statistical results were steam distillation, mesh size 50 and using ultrasounic device.

  13. Characterization of Carya illinoiensis and Juglans regia oils obtained by different extraction systems

    Directory of Open Access Journals (Sweden)

    Tainara Costa-Singh

    2015-05-01

    Full Text Available It is extremely important to evaluate the extraction processes of vegetable oils used in food, considering that the nuts are rich sources of triacylglycerols. Thus, the present study aimed at comparing the methods of solvent extraction and extraction by pressing of the lipid fractions of walnut (Juglans regia and pecan nut (Carya illinoensis, in order to elucidate their influence on the content of bioactive substances. The samples were analyzed regarding fatty acid profile, tocopherols, phytosterols, carotenoids, and phenolic compounds, presenting relevant quantities of these bioactive substances. It was found that the extraction of oils by pressing minimized degradation of tocopherol when compared to solvent extraction. However, solvent extraction is more efficient to extract bioactive compounds such as phytosterols, carotenoids, and phenolic compounds.

  14. Extraction of Citrus Hystrix D.C. (Kaffir Lime) Essential Oil Using Automated Steam Distillation Process: Analysis of Volatile Compounds

    International Nuclear Information System (INIS)

    Nurhani Kasuan; Zuraida Muhammad; Zakiah Yusoff; Mohd Hezri Fazalul Rahiman; Mohd Nasir Taib; Zaibunnisa Abdul Haiyee

    2013-01-01

    An automated steam distillation was successfully used to extract volatiles from Citrus hystrix D.C (Kaffir lime) peels. The automated steam distillation integrated with robust temperature control can commercially produce large amount of essential oil with efficient heating system. Objective of this study is to quantify the oil production rate using automated steam distillation and analyze the composition of volatiles in Kaffir lime peels oil at different controlled and uncontrolled temperature conditions. From the experimentation, oil extraction from Kaffir lime peels only took approximately less than 3 hours with amount of oil yield was 13.4 % more than uncontrolled temperature. The identified major compounds from Kaffir lime peels oil were sabinene, β-pinene, limonene, α-pinene, camphene, myrcene, terpinen-4-ol, α-terpineol, linalool, terpinolene and citronellal which are considered to have good organoleptic quality. In contrast with uncontrolled temperature, oil analysis revealed that some important volatile compounds were absent such as terpinolene, linalool, terpinen-4-ol due to thermal degradation effect from fast heating of extracted material. (author)

  15. Extraction of rice bran oil from local rice husk

    International Nuclear Information System (INIS)

    Anwar, J.; Zaman, W.; Salman, M.; Jabeen, N.

    2006-01-01

    Rice Bran Oil is widely used in pharmaceutical, food and chemical industries due to its unique properties and high medicinal value. In the present work, extraction of rice bran oil from different samples of rice husk collected from local rice shellers by solvent extraction method has been studied. Experiments were conducted using a soxhelt apparatus, to extract rice bran oil using hexane, petroleum ether, ethanol and methanol as the solvents and the yields obtained under different conditions were compared. Batch extraction tests showed that the rate of extraction decreases with time and the solution approaches saturation at an exponential rate. (author)

  16. Antioxidant Activity of Essential Oil Extracted by SC-CO₂ from Seeds of Trachyspermum ammi.

    Science.gov (United States)

    Singh, Aarti; Ahmad, Anees

    2017-07-11

    Bcakground: Extracts obtained from natural sources such as plants are of immense importance for humans. Methods: Therefore this study was conducted to obtain essential oil from the seeds of T. ammi by conventional and non-conventional methods. Hydrodistillation (HD), Solvent Extraction (SE), Ultrasonication (US), and Supercritical Carbon-dioxide (SC-CO₂) extraction techniques were used to extract essential oil from the powdered seeds of T. ammi . A quality control method for each extracted oil was developed using HPTLC, FTIR, and GC-MS. The optimization process was carried out using fractional factorial design (FFD) under which three parameters were considered: pressure (150, 175, and 300 bar), temperature (25, 30, and 40 °C), and CO₂ flow rate (5, 10, 15 g/min). Results: The yield of essential oil obtained from the HD, SE, US, and SC-CO₂ methods were 1.20%, 1.82%, 2.30%, and 2.64% v/w , respectively. Antioxidant activity was determined by the DPPH and superoxide scavenging methods and the IC 50 (Inhibition Concentration) values of the T. ammi oil sample were found to be 36.41 and 20.55 µg mL -1 , respectively. Conclusion: The present paper reported that different extraction methods lead to different yields of essential oils and the choice of a suitable method is extremely important to obtain more preferred compounds. The yield was higher in the SC-CO₂ method and it is a sustainable and green extraction technique. Many important constituents were detected in analytical techniques. Antioxidant activities carried out showed that essential oil extracted from T. ammi seeds possess significant antioxidant activity.

  17. Errors When Extracting Oil from Algae

    Science.gov (United States)

    Murphy, E.; Treat, R.; Ichiuji, T.

    2014-12-01

    Oil is in popular demand, but the worldwide amount of oil is decreasing and prices for it are steadily increasing. Leading scientists have been working to find a solution of attaining oil in an economically and environmentally friendly way. Researchers at the U.S. Department of Energy's Pacific Northwest National Laboratory (PNNL) have determined that "a small mixture of algae and water can be turned into crude oil in less than an hour" (Sheehan, Duhahay, Benemann, Poessler). There are various ways of growing the algae, such as closed loop and open loop methods, as well as processes of extracting oil, such as hydrothermal liquefaction and the hexane-solvent method. Our objective was to grow the algae (C. reinhardtii) and extract oil from it using NaOH and HCl, because we had easy access to those specific chemicals. After two trials of attempted algae growth, we discovered that a bacteria was killing off the algae. This led us to further contemplation on how this dead algae and bacteria are affecting our environment, and the organisms within it. Eutrophication occurs when excess nutrients stimulate rapid growth of algae in an aquatic environment. This can clog waterways and create algal blooms in blue-green algae, as well as neurotoxic red tide phytoplankton. These microscopic algae die upon consumption of the nutrients in water and are degraded by bacteria. The bacteria respires and creates an acidic environment with the spontaneous conversion of carbon dioxide to carbonic acid in water. This process of degradation is exactly what occurred in our 250 mL flask. When the phytoplankton attacked our algae, it created a hypoxic environment, which eliminated any remaining amounts of oxygen, carbon dioxide, and nutrients in the water, resulting in a miniature dead zone. These dead zones can occur almost anywhere where there are algae and bacteria, such as the ocean, and make it extremely difficult for any organism to survive. This experiment helped us realize the

  18. Studies on the extraction of wheat germ oil by commercial hexane

    Directory of Open Access Journals (Sweden)

    El Kinawy, Omayma S.

    2002-12-01

    Full Text Available Extraction of an edible oil from wheat germ, an important byproduct of wheat milling industry in Egypt, using commercial hexane was studied. The extraction was carried out in a single and in two successive stages using different solvent-to-solid ratios from 2 to 6 m3/ ton. The results showed that a good oil recovery (about 75% can be achieved using 4 m3 hexane for each ton germ extracted in a single stage. This amount of solvent can be reduced to 2.5 m3/ ton if the process is carried out in two successive stages. The study has shown also that the amount of oil recovered from wheat germ is not significantly affected by heating the extraction mixture during the extraction process. The developments of free acids and peroxides in the oil during the storage period of wheat germ prior to extraction and during the hot extraction process were also investigated.Se ha estudiado la extracción de un aceite comestible a partir del germen de trigo, importante subproducto de la industria de la molienda del trigo en Egipto, usando hexano comercial. La extracción se llevó a cabo en una etapa única y en dos sucesivas, usando diferentes relaciones solvente-sólido desde 2 a 6 m3/ton. Los resultados mostraron que una buena recuperación de aceite (alrededor del 75% puede alcanzarse usando 4 m3 de hexano por cada tonelada de germen extraído en una etapa única. Esta cantidad de solvente puede reducirse a 2’5 m3/ton si el proceso se lleva a cabo en dos etapas sucesivas. El estudio mostró también que la cantidad de aceite recuperada a partir del germen de trigo no se afectó significativamente por el calentamiento de la mezcla durante el proceso de extracción. También se estudió la producción de ácidos libres y peróxidos en el aceite durante el período de almacenamiento del germen de trigo anterior a la extracción y durante el proceso de extracción en caliente

  19. Deacidification of Soybean Oil Combining Solvent Extraction and Membrane Technology

    Directory of Open Access Journals (Sweden)

    M. L. Fornasero

    2013-01-01

    Full Text Available The aim of this work was to study the removal of free fatty acids (FFAs from soybean oil, combining solvent extraction (liquid-liquid for the separation of FFAs from the oil and membrane technology to recover the solvent through nanofiltration (NF. Degummed soybean oil containing 1.05 ± 0.10% w/w FFAs was deacidified by extraction with ethanol. Results obtained in the experiences of FFAs extraction from oil show that the optimal operating conditions are the following: 1.8 : 1 w : w ethanol/oil ratio, 30 minutes extraction time and high speed of agitation and 30 minutes repose time after extraction at ambient temperature. As a result of these operations two phases are obtained: deacidified oil phase and ethanol phase (containing the FFAs. The oil from the first extraction is subjected to a second extraction under the same conditions, reducing the FFA concentration in oil to 0.09%. Solvent recovery from the ethanol phase is performed using nanofiltration technology with a commercially available polymeric NF membrane (NF-99-HF, Alfa Laval. From the analysis of the results we can conclude that the optimal operating conditions are pressure of 20 bar and temperature of 35°C, allowing better separation performance: permeate flux of 28.3 L/m2·h and FFA retention of 70%.

  20. Physicochemical characterisation of hexanic seed oil extract from ...

    African Journals Online (AJOL)

    The physicochemical characterisation of oil extracts from Schinus molle seeds collected in South Africa was performed. The oils were extracted in hexane, physicochemical parameters determined and lipids profiled by gas chromatography, in order to determine its potential for use in industry, ethnomedicine and its ...

  1. Analysis of edible oil processing options for the BIO-Plex advanced life support system

    Science.gov (United States)

    Greenwalt, C. J.; Hunter, J.

    2000-01-01

    Edible oil is a critical component of the proposed plant-based Advanced Life Support (ALS) diet. Soybean, peanut, and single-cell oil are the oil source options to date. In terrestrial manufacture, oil is ordinarily extracted with hexane, an organic solvent. However, exposed solvents are not permitted in the spacecraft environment or in enclosed human tests by National Aeronautics and Space Administration due to their potential danger and handling difficulty. As a result, alternative oil-processing methods will need to be utilized. Preparation and recovery options include traditional dehulling, crushing, conditioning, and flaking, extrusion, pressing, water extraction, and supercritical extraction. These processing options were evaluated on criteria appropriate to the Advanced Life Support System and BIO-Plex application including: product quality, product stability, waste production, risk, energy needs, labor requirements, utilization of nonrenewable resources, usefulness of by-products, and versatility and mass of equipment to determine the most appropriate ALS edible oil-processing operation.

  2. Extraction of kiwi seed oil: Soxhlet versus four different non-conventional techniques.

    Science.gov (United States)

    Cravotto, Giancarlo; Bicchi, Carlo; Mantegna, Stefano; Binello, Arianna; Tomao, Valerie; Chemat, Farid

    2011-06-01

    Kiwi seed oil has a nutritionally interesting fatty acid profile, but a rather low oxidative stability, which requires careful extraction procedures and adequate packaging and storage. For these reasons and with the aim to achieve process intensification with shorter extraction time, lower energy consumption and higher yields, four different non-conventional techniques were experimented. Kiwi seeds were extracted in hexane using classic Soxhlet as well as under power ultrasound (US), microwaves (MWs; closed vessel) and MW-integrated Soxhlet. Supercritical CO₂ was also employed and compared to the other techniques in term of yield, extraction time, fatty acid profiles and organoleptic properties. All these non-conventional techniques are fast, effective and safe. A sensory evaluation test showed the presence of off-flavours in oil samples extracted by Soxhlet and US, an indicator of partial degradation.

  3. Antitumor effects and mechanisms of Ganoderma extracts and spores oil.

    Science.gov (United States)

    Chen, Chun; Li, Peng; Li, Ye; Yao, Guan; Xu, Jian-Hua

    2016-11-01

    Ganoderma lucidum is a popular herbal medicine used in China to promote health. Modern studies have disclosed that the active ingredients of Ganoderma can exhibit several effects, including antitumor effects and immunomodulation. The present study evaluated the antitumor effects of self-prepared Ganoderma extracts and spores oil, and investigated the possible underlying mechanisms by observing the effects of the extracts and oil on topoisomerases and the cell cycle. The results showed that Ganoderma extracts and spores oil presented dose-dependent inhibitory effects on tumor cells. The half maximal inhibitory concentration (IC 50 ) values of Ganoderma extracts on HL60, K562 and SGC-7901 cells for 24 h were 0.44, 0.39 and 0.90 mg/ml, respectively; for Ganoderma spores oil, the IC 50 values were 1.13, 2.27 and 6.29 mg/ml, respectively. In the in vivo study, the inhibitory rates of Ganoderma extracts (4 g/kg/d, intragastrically) on S180 and H22 cells were 39.1 and 44.6%, respectively, and for Ganoderma spores oil (1.2 g/kg/d, intragastrically) the inhibitory rates were 30.9 and 44.9%, respectively. Ganoderma extracts and spores oil inhibited the activities of topoisomerase I and II. Ganoderma spores oil was shown block the cell cycle at the transition between the G1 and S phases and induce a marked decrease in cyclin D1 levels in K562 cells, with no significant change in cyclin E level. These results suggest that the Ganoderma extracts and spores oil possessed antitumor effects in the in vitro and in vivo studies. The antitumor mechanisms of the extracts and spores oil were associated with inhibitory effects on topoisomerase I and II activities, and for Ganoderma spores oil, the antitumor effects may also be associated with decreased cyclin D1 levels, thus inducing G1 arrest in the cell cycle.

  4. Application of 2k Full Factorial Design in Optimization of Solvent-Free Microwave Extraction of Ginger Essential Oil

    Directory of Open Access Journals (Sweden)

    Mumtaj Shah

    2014-01-01

    Full Text Available The solvent-free microwave extraction of essential oil from ginger was optimized using a 23 full factorial design in terms of oil yield to determine the optimum extraction conditions. Sixteen experiments were carried out with three varying parameters, extraction time, microwave power, and type of sample for two levels of each. A first order regression equation best fits the experimental data. The predicted values calculated by the regression model were in good agreement with the experimental values. The results showed that the extraction time is the most prominent factor followed by microwave power level and sample type for extraction process. An average of 0.25% of ginger oil can be extracted using current setup. The optimum conditions for the ginger oil extraction using SFME were the extraction time 30 minutes, microwave power level 640 watts, and sample type, crushed sample. Solvent-free microwave extraction proves a green and promising technique for essential oil extraction.

  5. Reduction of Sulphur Content of Urals Crude Oil Prior to Processing ...

    African Journals Online (AJOL)

    during oxidation was carried out by extraction followed ... and from gas oil to 82 % (Gore et al., 2003). In 2004 ... treated light gas oil(LGO), it was reduced from 307 to ..... Oil Shale,. 23(2):164-176. Rappas, A.S. (2002). Process for removing low.

  6. The addition of pineapple flesh and pineapple peels extracts to increase the quality of used cooking oil

    Science.gov (United States)

    Kusumawardani, R.; Hasanah, N.; Sukemi

    2018-04-01

    In Indonesia, reuse of cooking oil is high and common. Heating process and reuse of the cooking oil causes a change in its chemical constituents and decrease its qualities. This research aimed to investigate the addition of pineapple flesh extract (PFE) and pineapple peel extract (PPE) on the increment of the quality of oxidized (used) cooking oil. The cooking oil has been used three times. Treatment was done by mixing the used cooking oil with the extract (2:1) at 50°C. Peroxide value, FFA and iodine number of treated and untreated used cooking oils were measured by using titration method. The result showed that the treatment could increase the quality of the used cooking oils. PPE was better than PFE to increase the quality of the used cooking oil.

  7. Process optimisation of microwave-assisted extraction of peony ( Paeonia suffruticosa Andr .) seed oil using hexane-ethanol mixture and its characterisation

    Science.gov (United States)

    Xiaoli Sun; Wengang Li; Jian Li; Yuangang Zu; Chung-Yun Hse; Jiulong Xie; Xiuhua Zhao

    2016-01-01

    Ethanol and hexane mixture agent microwave-assisted extraction (MAE) method was conducted to extract peony (Paeonia suffruticosa Andr.) seed oil (PSO). The aim of the study was to optimise the extraction for both yield and energy consumption in mixture agent MAE. The highest oil yield (34.49%) and lowest unit energy consumption (14 125.4 J g -1)...

  8. EXTRACTION OF OIL SEED PIN (Citrullus vulgaris BY LEACHING

    Directory of Open Access Journals (Sweden)

    Peggy Londoño

    2014-12-01

    Full Text Available Extraction of seed oil initially consisted in physicochemical study of the seed, in order to meet their nutritional content by performing various analyzes as moisture, ash, fat, phosphorus, proteins and carbohydrates. Then we proceeded with oil extraction equipment using solid-liquid extraction, Soxhlet using hexane as a solvent using the factorial design of the type 23. After, the crude oil was characterized and refined by the methodology of COVENIN norms, where the oil presented potential properties to elaborate soap in the cosmetic industry. Finally, a lipid profile was obtained by a gas chromatographic, the results showed highly unsaturated fatty acid contents (linoleic and oleic that gives it the potential to be applied as a capable oil with excellent properties and quality to human consume.

  9. Hydroxytyrosol extracts, olive oil and walnuts as functional components in chicken sausages.

    Science.gov (United States)

    Nieto, Gema; Martínez, Lorena; Castillo, Julian; Ros, Gaspar

    2017-08-01

    Olive oil, hydroxytyrosol and walnut can be considered ideal Mediterranean ingredients for their high polyphenolic content and healthy properties. Three extracts of hydroxytyrosol obtained using different extraction processes (HXT 1, 2, 3) (50 ppm) were evaluated for use as antioxidants in eight different chicken sausage formulas enriched in polyunsaturated fatty acids (2.5 g 100 g -1 walnut) or using extra virgin olive oil (20 g 100 g -1 ) as fat replacer. Lipid and protein oxidation, colour, emulsion stability, and the microstructure of the resulting chicken sausages were investigated and a sensory analysis was carried out. The sausages with HXT extracts were found to decrease lipid oxidation and to lead to the loss of thiol groups compared with control sausages. Emulsion stability (capacity to hold water and fat) was greater in the sausages containing olive oil and walnut than in control sausages. In contrast, the HXT extracts produced high emulsion instability (increasing cooking losses). Sensory analysis suggested that two of the HXT extracts studied (HXT 2 and HXT 3 ) were unacceptable, while the acceptability of the other was similar to that of the control products. Sausages incorporating HXT showed different structures than control samples or sausages with olive oil, related to the composition of the emulsion. These results suggest the possibility of replacing animal fat by olive oil and walnut in order to produce healthy meat products. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  10. Bioactive compounds and quality parameters of avocado oil obtained by different processes.

    Science.gov (United States)

    Krumreich, Fernanda D; Borges, Caroline D; Mendonça, Carla Rosane B; Jansen-Alves, Cristina; Zambiazi, Rui C

    2018-08-15

    The objective of this study was to evaluate the quality of avocado oil whose pulp was processed through different drying and oil extraction methods. The physicochemical characteristics of avocados cv. Breda were determined after drying the pulp in an oven under ventilation (40 °C and 60 °C) and vacuum oven (60 °C), followed by the oil extracted by mechanical pressing or the Soxhlet method. From the approximately 72% pulp found in the avocado fruit, the 16% fraction is lipids. The quality indices evaluated in avocado oil showed better results when the pulp was dried at 60 °C under vacuum and oil extraction was done by the Soxhlet method with petroleum ether, whereas the bioactive compounds were better preserved when the avocado pulp was dried at 60 °C under ventilation and mechanical pressing was used for the oil extraction. Among the fatty acids found, oleic acid was the main. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. A Green Protocol for Microwave-Assisted Extraction of Volatile Oil Terpenes from Pterodon emarginatus Vogel. (Fabaceae

    Directory of Open Access Journals (Sweden)

    Giuliana M. Vila Verde

    2018-03-01

    Full Text Available Microwave-assisted extraction of volatile oils (MAE potentially offers a more efficient and bio-sustainable method than conventional extraction by Clevenger apparatus (CE. This study aimed to optimise the MAE of the volatile oil from Pterodon emarginatus fruits and characterise the volatile compounds. A 23 full-factorial central composite design and response surface methodology were used to evaluate the effects of time (min, moisture (% and microwave power (W on the extraction yield. The process optimisation was based on the desirability function approach. The reaction time and moisture conditions were standardised in these analyses. The volatile oil composition was analysed by Gas Chromatography/Mass Spectrometry (GC/MS in order to compare techniques extractions influences. Microwave irradiation showed excellent performance for extraction of the volatile oil from Pterodon emarginatus and there were some advantages in compare to conventional method with respect to the time (14 times, energy (6 times, reagents amounts and waste formation. About chemical composition presents significant differences with the type of extraction. Caryophyllene (25.65% and trans-α-bisabolol (6.24% were identified as major components in MAE sample while caryophyllene (6.75% and γ-elemene (7.02% are the components with higher relative percentage in CE samples. The microwaves assisted process shown an increase of economic interested compounds present in volatile oil.

  12. Ultrasound-assisted extraction (UAE) and solvent extraction of papaya seed oil: yield, fatty acid composition and triacylglycerol profile.

    Science.gov (United States)

    Samaram, Shadi; Mirhosseini, Hamed; Tan, Chin Ping; Ghazali, Hasanah Mohd

    2013-10-10

    The main objective of the current work was to evaluate the suitability of ultrasound-assisted extraction (UAE) for the recovery of oil from papaya seed as compared to conventional extraction techniques (i.e., Soxhlet extraction (SXE) and solvent extraction (SE)). In the present study, the recovery yield, fatty acid composition and triacylglycerol profile of papaya seed oil obtained from different extraction methods and conditions were compared. Results indicated that both solvent extraction (SE, 12 h/25 °C) and ultrasound-assisted extraction (UAE) methods recovered relatively high yields (79.1% and 76.1% of total oil content, respectively). Analysis of fatty acid composition revealed that the predominant fatty acids in papaya seed oil were oleic (18:1, 70.5%-74.7%), palmitic (16:0, 14.9%-17.9%), stearic (18:0, 4.50%-5.25%), and linoleic acid (18:2, 3.63%-4.6%). Moreover, the most abundant triacylglycerols of papaya seed oil were triolein (OOO), palmitoyl diolein (POO) and stearoyl oleoyl linolein (SOL). In this study, ultrasound-assisted extraction (UAE) significantly (p < 0.05) influenced the triacylglycerol profile of papaya seed oil, but no significant differences were observed in the fatty acid composition of papaya seed oil extracted by different extraction methods (SXE, SE and UAE) and conditions.

  13. Modelling long-term oil price and extraction with a Hubbert approach: The LOPEX model

    International Nuclear Information System (INIS)

    Rehrl, Tobias; Friedrich, Rainer

    2006-01-01

    The LOPEX (Long-term Oil Price and EXtraction) model generates long-term scenarios about future world oil supply and corresponding price paths up to the year 2100. In order to determine oil production in non-OPEC countries, the model uses Hubbert curves. Hubbert curves reflect the logistic nature of the discovery process and the associated constraint on temporal availability of oil. Extraction paths and world oil price path are both derived endogenously from OPEC's intertemporally optimal cartel behaviour. Thereby OPEC is faced with both the price-dependent production of the non-OPEC competitive fringe and the price-dependent world oil demand. World oil demand is modelled with a constant price elasticity function and refers to a scenario from ACROPOLIS-POLES. LOPEX results indicate a significant higher oil price from around 2020 onwards compared to the reference scenario, and a stagnating market share of maximal 50% to be optimal for OPEC

  14. Desulfurization of AL-Ahdab Crude Oil using Oxidative Processes

    Directory of Open Access Journals (Sweden)

    Neran Khalel Ibrahim

    2015-07-01

    Full Text Available Two different oxidative desulfurization strategies based on oxidation/adsorption or oxidation/extraction were evaluated for the desulfurization of AL-Ahdab (AHD sour crude oil (3.9wt% sulfur content. In the oxidation process, a homogenous oxidizing agent comprising of hydrogen peroxide and formic acid was used. Activated carbons were used as sorbent/catalyst in the oxidation/adsorption process while acetonitrile was used as an extraction solvent in the oxidation/extraction process. For the oxidation/adsorption scheme, the experimental results indicated that the oxidation desulfurization efficiency was enhanced on using activated carbon as catalyst/sorbent. The effects of the operating conditions (contact time, temperature, mixing speed and sorbent dose on the desulfurization efficiency were examined. The desulfurization efficiency measured at the best operating conditions(optimum conditions: 60 , 500rpm, 60min contact time and sorbent dose of 0.7g AC/100 ml AHD crude, was 32.8% corresponding to a sulfur content of 2.6 wt%. Applying the same optimum operating conditions and at 3:1 solvent/oil ratio, the oxidation/extraction method gave comparable desulfurization efficiency of 31.5%.

  15. Use of a Combined Technology of Ultrasonication, Three-Phase Partitioning, and Aqueous Enzymatic Oil Extraction for the Extraction of Oil from Spirogyra sp.

    Directory of Open Access Journals (Sweden)

    Adisheshu Reddy

    2014-01-01

    Full Text Available Algal oil from Spirogyra sp. was extracted using a combined technology of ultrasonication, three-phase partitioning, and aqueous enzymatic oil extraction. Ultrasonication was done to rupture the cell wall and papain was used for an easier release of the trapped oil. The salt concentration for three-phase partitioning, preincubation period with (or without the protease, and its operational temperature were optimized for a maximum possible yield of the oil and the effect of ultrasonication, and three-phase partitioning with (or without the protease were studied. It was found that under optimized conditions at 50% ammonium sulphate concentration using tert-butanol (in 1 : 1, v/v ratio a presonicated and papain treated algal suspension could produce 24% (w/w, dry weight oil within few hours which was ten times higher as compared to the oil obtained by Soxhlet extraction using hexane and two times higher than the oil obtained without using the protease.

  16. Microwave-Assisted Extraction and Physicochemical Evaluation of Oil from Hevea brasiliensis Seeds

    Directory of Open Access Journals (Sweden)

    Evelyn C. Creencia

    2018-04-01

    Full Text Available The rubber tree (Hevea brasiliensis is exploited mainly for latex in view of its economic importance. However, one of its auxiliary products, the rubber seed, does not find any major applications, and hence, even the natural production of seeds itself remains underutilized. In this study, microwave-assisted Soxhlet extraction is used as a green alternative to extract the oil from seeds at a reaction time of 90 min and microwave power of 300 W. The objective of the study is to evaluate the effects of the processing conditions, including drying time, temperature, solid–solvent ratio, and extraction solvent, on the yield of rubber seed oil. Moreover, the microwave-assisted aqueous extraction (MAAE under acidic conditions is also investigated. Based on the results, n-hexane gave the best yield at an optimized 1:20 seed–hexane ratio at 72 °C compared with the conventional Soxhlet method and the acidic MAAE. Furthermore, the chemical characteristics of the oil showed a high value of free fatty acids (% FFA (1.15–7.61% and an iodine value (IV that ranges from 100–150. As a semi-drying oil, rubber seed oil (RSO can be used as an ingredient for surface coating and in the formulation of products where the presence of unsaturation is important.

  17. Agrochemical characterization of vermicomposts produced from residues of Palo Santo (Bursera graveolens) essential oil extraction

    DEFF Research Database (Denmark)

    Carrión-Paladines, Vinicio; Fries, Andreas; Gomez Muñoz, Beatriz

    2016-01-01

    Fruits of Palo Santo (Bursera graveolens) are used for essential oil extraction. The extraction process is very efficient, because up to 3% of the fresh fruits can be transformed into essential oil; however, a considerable amount of waste is concurrently produced (>97% of the fresh biomass). Rece...

  18. Antitumor effects and mechanisms of Ganoderma extracts and spores oil

    Science.gov (United States)

    Chen, Chun; Li, Peng; Li, Ye; Yao, Guan; Xu, Jian-Hua

    2016-01-01

    Ganoderma lucidum is a popular herbal medicine used in China to promote health. Modern studies have disclosed that the active ingredients of Ganoderma can exhibit several effects, including antitumor effects and immunomodulation. The present study evaluated the antitumor effects of self-prepared Ganoderma extracts and spores oil, and investigated the possible underlying mechanisms by observing the effects of the extracts and oil on topoisomerases and the cell cycle. The results showed that Ganoderma extracts and spores oil presented dose-dependent inhibitory effects on tumor cells. The half maximal inhibitory concentration (IC50) values of Ganoderma extracts on HL60, K562 and SGC-7901 cells for 24 h were 0.44, 0.39 and 0.90 mg/ml, respectively; for Ganoderma spores oil, the IC50 values were 1.13, 2.27 and 6.29 mg/ml, respectively. In the in vivo study, the inhibitory rates of Ganoderma extracts (4 g/kg/d, intragastrically) on S180 and H22 cells were 39.1 and 44.6%, respectively, and for Ganoderma spores oil (1.2 g/kg/d, intragastrically) the inhibitory rates were 30.9 and 44.9%, respectively. Ganoderma extracts and spores oil inhibited the activities of topoisomerase I and II. Ganoderma spores oil was shown block the cell cycle at the transition between the G1 and S phases and induce a marked decrease in cyclin D1 levels in K562 cells, with no significant change in cyclin E level. These results suggest that the Ganoderma extracts and spores oil possessed antitumor effects in the in vitro and in vivo studies. The antitumor mechanisms of the extracts and spores oil were associated with inhibitory effects on topoisomerase I and II activities, and for Ganoderma spores oil, the antitumor effects may also be associated with decreased cyclin D1 levels, thus inducing G1 arrest in the cell cycle. PMID:27900038

  19. Technical difficulties and solutions of direct transesterification process of microbial oil for biodiesel synthesis.

    Science.gov (United States)

    Yousuf, Abu; Khan, Maksudur Rahman; Islam, M Amirul; Wahid, Zularisam Ab; Pirozzi, Domenico

    2017-01-01

    Microbial oils are considered as alternative to vegetable oils or animal fats as biodiesel feedstock. Microalgae and oleaginous yeast are the main candidates of microbial oil producers' community. However, biodiesel synthesis from these sources is associated with high cost and process complexity. The traditional transesterification method includes several steps such as biomass drying, cell disruption, oil extraction and solvent recovery. Therefore, direct transesterification or in situ transesterification, which combines all the steps in a single reactor, has been suggested to make the process cost effective. Nevertheless, the process is not applicable for large-scale biodiesel production having some difficulties such as high water content of biomass that makes the reaction rate slower and hurdles of cell disruption makes the efficiency of oil extraction lower. Additionally, it requires high heating energy in the solvent extraction and recovery stage. To resolve these difficulties, this review suggests the application of antimicrobial peptides and high electric fields to foster the microbial cell wall disruption.

  20. Green solvents and technologies for oil extraction from oilseeds.

    Science.gov (United States)

    Kumar, S P Jeevan; Prasad, S Rajendra; Banerjee, Rintu; Agarwal, Dinesh K; Kulkarni, Kalyani S; Ramesh, K V

    2017-01-01

    Oilseeds are crucial for the nutritional security of the global population. The conventional technology used for oil extraction from oilseeds is by solvent extraction. In solvent extraction, n -hexane is used as a solvent for its attributes such as simple recovery, non-polar nature, low latent heat of vaporization (330 kJ/kg) and high selectivity to solvents. However, usage of hexane as a solvent has lead to several repercussions such as air pollution, toxicity and harmfulness that prompted to look for alternative options. To circumvent the problem, green solvents could be a promising approach to replace solvent extraction. In this review, green solvents and technology like aqueous assisted enzyme extraction are better solution for oil extraction from oilseeds. Enzyme mediated extraction is eco-friendly, can obtain higher yields, cost-effective and aids in obtaining co-products without any damage. Enzyme technology has great potential for oil extraction in oilseed industry. Similarly, green solvents such as terpenes and ionic liquids have tremendous solvent properties that enable to extract the oil in eco-friendly manner. These green solvents and technologies are considered green owing to the attributes of energy reduction, eco-friendliness, non-toxicity and non-harmfulness. Hence, the review is mainly focussed on the prospects and challenges of green solvents and technology as the best option to replace the conventional methods without compromising the quality of the extracted products.

  1. Characterization of Arachis hypogaea L. oil obtained from different extraction techniques and in vitro antioxidant potential of supercritical fluid extraction extract

    Directory of Open Access Journals (Sweden)

    Rishika Chauhan

    2016-01-01

    Full Text Available Aim: The present investigation was aimed to characterize the fixed oil of Arachis hypogaea L. using five different extraction methods: Supercritical fluid extraction (SFE, ultrasound assistance extraction, soxhlet extraction, solvent extraction, and three phase partitioning method. Materials and Methods: The SFE conditions (temperature, pressure, and volume of CO 2 were optimized prior for better yield. The extracted oils were analyzed and compared for their physiochemical parameters, high-performance thin layer chromatography (HPTLC, gas chromatography-mass spectrometry (GC-MS, and Fourier transform infrared spectrometry (FT-IR fingerprinting. Anti-oxidant activity was also determined using DPPH and superoxide scavenging method. Results: The main fatty acids were oleic, linoleic, palmitic, and stearic acids as obtained by GC-MS. HPTLC analysis revealed the presence of similar major components in chromatograms. Similarly, the pattern of peaks as obtained in FT-IR and GC-MS spectra of same oils by different extraction methods was superimposable. Conclusion: Analysis reported that the fixed oil of A. hypogaea L. is a good source of unsaturated fatty acid, mainly n-6 and n-9 fatty acid with a significant antioxidant activity of oil obtained from SFE extraction method.

  2. Extraction/fractionation and deacidification of wheat germ oil using supercritical carbon dioxide

    Directory of Open Access Journals (Sweden)

    P. Zacchi

    2006-03-01

    Full Text Available Wheat germ oil was obtained by mechanical pressing using a small-scale screw press and by supercritical extraction in a pilot plant. With this last method, different pressures and temperatures were tested and the tocopherol concentration in the extract was monitored during extraction. Then supercritical extracted oil as well as commercial pressed oil were deacidified in a countercurrent column using supercritical carbon dioxide as solvent under different operating conditions. Samples of extract, refined oil and feed oil were analyzed for free fatty acids (FFA and tocopherol contents. The results show that oil with a higher tocopherol content can be obtained by supercritical extraction-fractionation and that FFA can be effectively removed by countercurrent rectification while the tocopherol content is only slightly reduced.

  3. Process for the extraction of valuable products from coals, pitches, mineral oils, and the like

    Energy Technology Data Exchange (ETDEWEB)

    1936-06-05

    A process is described for the treating of coke, lignite, peat, etc., and mineral oils with the help of hydrogen or other reducing gases and under pressure to recover valuable hydrocarbons, characterized by the carbonaceous substances and the reducing gas coming together already heated totally or in part at least from 350/sup 0/C to the temperature necessary for the reaction. The substances to be treated becoming extracted in the form of paste or liquid from the reaction chamber and then returned to it and being reacted outside the reaction zone in the presence of the reducing gases at the temperature necessary for the reaction.

  4. Ultrasound-Assisted Extraction (UAE and Solvent Extraction of Papaya Seed Oil: Yield, Fatty Acid Composition and Triacylglycerol Profile

    Directory of Open Access Journals (Sweden)

    Hasanah Mohd Ghazali

    2013-10-01

    Full Text Available The main objective of the current work was to evaluate the suitability of ultrasound-assisted extraction (UAE for the recovery of oil from papaya seed as compared to conventional extraction techniques (i.e., Soxhlet extraction (SXE and solvent extraction (SE. In the present study, the recovery yield, fatty acid composition and triacylglycerol profile of papaya seed oil obtained from different extraction methods and conditions were compared. Results indicated that both solvent extraction (SE, 12 h/25 °C and ultrasound-assisted extraction (UAE methods recovered relatively high yields (79.1% and 76.1% of total oil content, respectively. Analysis of fatty acid composition revealed that the predominant fatty acids in papaya seed oil were oleic (18:1, 70.5%–74.7%, palmitic (16:0, 14.9%–17.9%, stearic (18:0, 4.50%–5.25%, and linoleic acid (18:2, 3.63%–4.6%. Moreover, the most abundant triacylglycerols of papaya seed oil were triolein (OOO, palmitoyl diolein (POO and stearoyl oleoyl linolein (SOL. In this study, ultrasound-assisted extraction (UAE significantly (p < 0.05 influenced the triacylglycerol profile of papaya seed oil, but no significant differences were observed in the fatty acid composition of papaya seed oil extracted by different extraction methods (SXE, SE and UAE and conditions.

  5. Extraction methods of Amaranthus sp. grain oil isolation.

    Science.gov (United States)

    Krulj, Jelena; Brlek, Tea; Pezo, Lato; Brkljača, Jovana; Popović, Sanja; Zeković, Zoran; Bodroža Solarov, Marija

    2016-08-01

    Amaranthus sp. is a fast-growing crop with well-known beneficial nutritional values (rich in protein, fat, dietary fiber, ash, and minerals, especially calcium and sodium, and containing a higher amount of lysine than conventional cereals). Amaranthus sp. is an underexploited plant source of squalene, a compound of high importance in the food, cosmetic and pharmaceutical industries. This paper has examined the effects of the different extraction methods (Soxhlet, supercritical fluid and accelerated solvent extraction) on the oil and squalene yield of three genotypes of Amaranthus sp. grain. The highest yield of the extracted oil (78.1 g kg(-1) ) and squalene (4.7 g kg(-1) ) in grain was obtained by accelerated solvent extraction (ASE) in genotype 16. Post hoc Tukey's HSD test at 95% confidence limit showed significant differences between observed samples. Principal component analysis (PCA) and cluster analysis (CA) were used for assessing the effect of different genotypes and extraction methods on oil and squalene yield, and also the fatty acid composition profile. Using coupled PCA and CA of observed samples, possible directions for improving the quality of product can be realized. The results of this study indicate that it is very important to choose both the right genotype and the right method of extraction for optimal oil and squalene yield. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

  6. The Protective Effect of Hippophae Rhamnoides Carotenoid Extract Against Lipid Peroxidation in Crude Vegetable Oils

    Directory of Open Access Journals (Sweden)

    Sanda Andrei

    2014-11-01

    Full Text Available Vegetable oils are important elements of the human diet because they contain essential nutritional factors. Due to the manufacturing processes or inadequate conditions of storage, they may also contain lipid oxidation products that are toxic to the body. The purpose of this paper is to test the protective effect of carotenoid-rich extracts obtained from the fruits of Hippophae rhamnoides on crude sunflower, pumpkin and olive oils oxidative processes. In order to evaluate the effect of antioxidant carotenoids, three stages were followed: thermal induction of lipid peroxidation in the presence of AAPH (2,2'-Azobis(2-amidinopropane dihydrochloride; determination of the level of lipid peroxidation in oxidized oils in the presence and absence of antioxidants, by quantifying the concentration of conjugated dienes and malonyl dialdehyde (MDA; determination of the level of lipid peroxidation by evaluating the profile of the fatty acids and the ratio between the saturated and unsaturated fatty acids (UFA / SFA, using an GC-MS method. In the case of sunflower oil, it was observed that sea buckthorn fruit extract significantly decreased MDA concentration but does not significantly reduce the concentration of conjugated dienes. The protective effect of carotenoids is more evident in the case of oil from pumpkin seeds. In the olive oil, unlike the first two types of oils, the carotenoids extract inhibits both the MDA and the conjugated dienes formation to a lesser extent, statistically insignificant. Overall, the ratio UFA / SFA decreases in crude oxidized oils. In the oils in which carotenoids were added was observed an increase in the UFA / SFA ratio. Carotenoids fraction from sea buckthorn fruits, rich in xanthophylls’ esters, possess a good antioxidant effect, protecting vegetable oils against peroxidation processes induced in the presence of AAPH

  7. Alternative to conventional extraction of vetiver oil: Microwave hydrodistillation of essential oil from vetiver roots (Vetiveria zizanioides)

    Science.gov (United States)

    Kusuma, H. S.; Altway, A.; Mahfud, M.

    2017-12-01

    In this study the extraction of essential oil from vetiver roots (Vetiveria zizanioides) has been carried out by using microwave hydrodistillation. In the extraction of vetiver oil using microwave hydrodistillation method is studied the effect of microwave power, feed to solvent (F/S) ratio and extraction time on the yield of vetiver oil. Besides, in this study can be seen that microwave hydrodistillation method offers important advantages over hydrodistillation, such as shorter extraction time (3 h vs. 24 h for hydrodistillation); better yields (0.49% vs. 0.46% for hydrodistillation); and environmental impact (energy cost is appreciably higher for performing hydrodistillation than that required for extraction using microwave hydrodistillation). Based on the analysis using GC-MS can be seen 19 components on vetiver oil that has been extracted using microwave hydrodistillation. In addition, GC-MS analysis showed that the main components of vetiver oil that has been extracted using microwave hydrodistillation method were β-Gurjunene (30.12%), α-Vetivone (20.12%), 4-(1-cyclohexenyl)-2-trimethylsilymethyl-1-buten-3-yne (13.52%) and δ-Selinene (7.27%).

  8. Burn drug made from ozonated vegetable oil mixture with white tumeric and cassava leaves extract

    Directory of Open Access Journals (Sweden)

    Moulydia Farah

    2018-01-01

    Full Text Available This research aims to create a burn treatment performed with ozonation process from a mixture of vegetable oil and added extracts of herbal ingredients. Ozonation on vegetable oils proven to kill bacteria and safe for the body. Ozonated vegetable oil produced from the ozone reactor batch process by doing a variety of extraction mixture to Oleozon® and vegetable oils. Then the results of ozonation is added extracts of herbal ingredients that cassava leaves and white turmeric to increase effectiveness in killing bacteria. Cassava leaves have anti-inflammatory agent, namely Vitamin C. While white turmeric Curcuma zedoaria have substance, which of the two compounds can inhibit and kill bacteria. The quality of ozonated oil (Oleozon® analytically were tested by the method of iodine number, acid number, peroxide number, and FTIR. Ozonation increased the peroxide and acid values for both oils, the increase being higher for mixture of coconut oil and soybean oil. The results of such mixing is then tested in bacteria to determine their effectiveness in killing the bacteria. The best ozonation condition is in an increase of 386,85% acid value, peroxide value about 102,91 meq/kg oil, and decrease in iodine number up to 21%. The result showed that under these conditions, ozonized oil has an antiseptic effect against Staphylococcus aureus. The final results of this study are expected to be a new innovation in the healing of skin wounds caused by burns as an anti-inflammatory that is effective, safe, and environmentally friendly.

  9. Antioxidant Activity of Essential Oil Extracted by SC-CO2 from Seeds of Trachyspermum ammi

    Directory of Open Access Journals (Sweden)

    Aarti Singh

    2017-07-01

    Full Text Available Bcakground: Extracts obtained from natural sources such as plants are of immense importance for humans. Methods: Therefore this study was conducted to obtain essential oil from the seeds of T. ammi by conventional and non-conventional methods. Hydrodistillation (HD, Solvent Extraction (SE, Ultrasonication (US, and Supercritical Carbon-dioxide (SC-CO2 extraction techniques were used to extract essential oil from the powdered seeds of T. ammi. A quality control method for each extracted oil was developed using HPTLC, FTIR, and GC-MS. The optimization process was carried out using fractional factorial design (FFD under which three parameters were considered: pressure (150, 175, and 300 bar, temperature (25, 30, and 40 °C, and CO2 flow rate (5, 10, 15 g/min. Results: The yield of essential oil obtained from the HD, SE, US, and SC-CO2 methods were 1.20%, 1.82%, 2.30%, and 2.64% v/w, respectively. Antioxidant activity was determined by the DPPH and superoxide scavenging methods and the IC50 (Inhibition Concentration values of the T. ammi oil sample were found to be 36.41 and 20.55 µg mL−1, respectively. Conclusion: The present paper reported that different extraction methods lead to different yields of essential oils and the choice of a suitable method is extremely important to obtain more preferred compounds. The yield was higher in the SC-CO2 method and it is a sustainable and green extraction technique. Many important constituents were detected in analytical techniques. Antioxidant activities carried out showed that essential oil extracted from T. ammi seeds possess significant antioxidant activity.

  10. Antioxidant Activity of Essential Oil Extracted by SC-CO2 from Seeds of Trachyspermum ammi

    Science.gov (United States)

    Singh, Aarti; Ahmad, Anees

    2017-01-01

    Bcakground: Extracts obtained from natural sources such as plants are of immense importance for humans. Methods: Therefore this study was conducted to obtain essential oil from the seeds of T. ammi by conventional and non-conventional methods. Hydrodistillation (HD), Solvent Extraction (SE), Ultrasonication (US), and Supercritical Carbon-dioxide (SC-CO2) extraction techniques were used to extract essential oil from the powdered seeds of T. ammi. A quality control method for each extracted oil was developed using HPTLC, FTIR, and GC-MS. The optimization process was carried out using fractional factorial design (FFD) under which three parameters were considered: pressure (150, 175, and 300 bar), temperature (25, 30, and 40 °C), and CO2 flow rate (5, 10, 15 g/min). Results: The yield of essential oil obtained from the HD, SE, US, and SC-CO2 methods were 1.20%, 1.82%, 2.30%, and 2.64% v/w, respectively. Antioxidant activity was determined by the DPPH and superoxide scavenging methods and the IC50 (Inhibition Concentration) values of the T. ammi oil sample were found to be 36.41 and 20.55 µg mL−1, respectively. Conclusion: The present paper reported that different extraction methods lead to different yields of essential oils and the choice of a suitable method is extremely important to obtain more preferred compounds. The yield was higher in the SC-CO2 method and it is a sustainable and green extraction technique. Many important constituents were detected in analytical techniques. Antioxidant activities carried out showed that essential oil extracted from T. ammi seeds possess significant antioxidant activity. PMID:28930268

  11. Oil quality of passion fruit seeds subjected to a pulp-waste purification process

    Directory of Open Access Journals (Sweden)

    Suelen Alvarenga Regis

    2015-06-01

    Full Text Available Passion fruit seeds must be clean and dry before the extraction processing to obtain high-quality oil for edible and cosmetic purposes. This research studies the viability of a cleaning process of seeds by evaluating the oil quality. The research examined 2 maturation stages of the fruit and one purification process of the seeds, compared to the control. The oil quality was evaluated by fatty acid composition, acidity, peroxide value and oxidative stability. The pulp waste suffered a thermal treatment in an alkaline water solution at 60°C for 10min and was further purified in an experimental decanter. In the control treatment, the pulp waste was processed using only water at ambient conditions. The passion fruit seeds were totally cleaned by the thermal/chemical treatment, allowing a faster drying (less than 50% of the drying time of the seeds and a bit higher yield of oil extraction (proportionally around 7.7%, without changes in quality of the oil

  12. Full Characterization of CO2-Oil Properties On-Chip: Solubility, Diffusivity, Extraction Pressure, Miscibility, and Contact Angle.

    Science.gov (United States)

    Sharbatian, Atena; Abedini, Ali; Qi, ZhenBang; Sinton, David

    2018-02-20

    Carbon capture, storage, and utilization technologies target a reduction in net CO 2 emissions to mitigate greenhouse gas effects. The largest such projects worldwide involve storing CO 2 through enhanced oil recovery-a technologically and economically feasible approach that combines both storage and oil recovery. Successful implementation relies on detailed measurements of CO 2 -oil properties at relevant reservoir conditions (P = 2.0-13.0 MPa and T = 23 and 50 °C). In this paper, we demonstrate a microfluidic method to quantify the comprehensive suite of mutual properties of a CO 2 and crude oil mixture including solubility, diffusivity, extraction pressure, minimum miscibility pressure (MMP), and contact angle. The time-lapse oil swelling/extraction in response to CO 2 exposure under stepwise increasing pressure was quantified via fluorescence microscopy, using the inherent fluorescence property of the oil. The CO 2 solubilities and diffusion coefficients were determined from the swelling process with measurements in strong agreement with previous results. The CO 2 -oil MMP was determined from the subsequent oil extraction process with measurements within 5% of previous values. In addition, the oil-CO 2 -silicon contact angle was measured throughout the process, with contact angle increasing with pressure. In contrast with conventional methods, which require days and ∼500 mL of fluid sample, the approach here provides a comprehensive suite of measurements, 100-fold faster with less than 1 μL of sample, and an opportunity to better inform large-scale CO 2 projects.

  13. Developing novel one-step processes for obtaining food-grade O/W emulsions from pressurized fluid extracts: processes description, state of the art and perspectives

    Directory of Open Access Journals (Sweden)

    Diego Tresinari SANTOS

    2015-01-01

    Full Text Available AbstractIn this work, a novel on-line process for production of food-grade emulsions containing oily extracts, i.e. oil-in-water (O/W emulsions, in only one step is presented. This process has been called ESFE, Emulsions from Supercritical Fluid Extraction. With this process, emulsions containing supercritical fluid extracts can be obtained directly from plant materials. The aim in the conception of this process is to propose a new rapid way to obtain emulsions from supercritical fluid extracts. Nowadays the conventional emulsion formulation method is a two-step procedure, i.e. first supercritical fluid extraction for obtaining an extract; secondly emulsion formulation using another device. Other variation of the process was tested and successfully validated originating a new acronymed process: EPFE (Emulsions from Pressurized Fluid Extractions. Both processes exploit the supercritical CO2-essential oils miscibility, in addition, EPFE process exploits the emulsification properties of saponin-rich pressurized aqueous plant extracts. The feasibility of this latter process was demonstrated using Pfaffia glomerata roots as source of saponin-rich extract, water as extracting solvent and clove essential oil, directly extracted using supercritical CO2, as a model dispersed phase. In addition, examples of pressurized fluid-based coupled processes applied for adding value to food bioactive compounds developed in the past five years are reviewed.

  14. Box-Behnken design for investigation of microwave-assisted extraction of patchouli oil

    Science.gov (United States)

    Kusuma, Heri Septya; Mahfud, Mahfud

    2015-12-01

    Microwave-assisted extraction (MAE) technique was employed to extract the essential oil from patchouli (Pogostemon cablin). The optimal conditions for microwave-assisted extraction of patchouli oil were determined by response surface methodology. A Box-Behnken design (BBD) was applied to evaluate the effects of three independent variables (microwave power (A: 400-800 W), plant material to solvent ratio (B: 0.10-0.20 g mL-1) and extraction time (C: 20-60 min)) on the extraction yield of patchouli oil. The correlation analysis of the mathematical-regression model indicated that quadratic polynomial model could be employed to optimize the microwave extraction of patchouli oil. The optimal extraction conditions of patchouli oil was microwave power 634.024 W, plant material to solvent ratio 0.147648 g ml-1 and extraction time 51.6174 min. The maximum patchouli oil yield was 2.80516% under these optimal conditions. Under the extraction condition, the experimental values agreed with the predicted results by analysis of variance. It indicated high fitness of the model used and the success of response surface methodology for optimizing and reflect the expected extraction condition.

  15. Carbon Disulfide (CS2) Interference in Glucose Metabolism from Unconventional Oil and Gas Extraction and Processing Emissions.

    Science.gov (United States)

    Rich, Alisa L; Patel, Jay T; Al-Angari, Samiah S

    2016-01-01

    Carbon disulfide (CS2) has been historically associated with the manufacturing of rayon, cellophane, and carbon tetrachloride production. This study is one of the first to identify elevated atmospheric levels of CS2 above national background levels and its mechanisms to dysregulate normal glucose metabolism. Interference in glucose metabolism can indirectly cause other complications (diabetes, neurodegenerative disease, and retinopathy), which may be preventable if proper precautions are taken. Rich et al found CS2 and 12 associated sulfide compounds present in the atmosphere in residential areas where unconventional shale oil and gas extraction and processing operations were occurring. Ambient atmospheric concentrations of CS2 ranged from 0.7 parts per billion by volume (ppbv) to 103 ppbv over a continuous 24-hour monitoring period. One-hour ambient atmospheric concentrations ranged from 3.4 ppbv to 504.6 ppbv. Using the U.S. Environmental Protection Agency Urban Air Toxic Monitoring Program study as a baseline comparison for atmospheric CS2 concentrations found in this study, it was determined that CS2 atmospheric levels were consistently elevated in areas where unconventional oil and gas extraction and processing occurred. The mechanisms by which CS2 interferes in normal glucose metabolism by dysregulation of the tryptophan metabolism pathway are presented in this study. The literature review found an increased potential for alteration of normal glucose metabolism in viscose rayon occupational workers exposed to CS2. Occupational workers in the energy extraction industry exposed to CS2 and other sulfide compounds may have an increased potential for glucose metabolism interference, which has been an indicator for diabetogenic effect and other related health impacts. The recommendation of this study is for implementation of regular monitoring of blood glucose levels in CS2-exposed populations as a preventative health measure.

  16. The extraction of essential oil from patchouli leaves (Pogostemon cablin Benth) using microwave hydrodistillation and solvent-free microwave extraction methods

    Science.gov (United States)

    Putri, D. K. Y.; Kusuma, H. S.; Syahputra, M. E.; Parasandi, D.; Mahfud, M.

    2017-12-01

    Patchouli plant (Pogostemon cablin Benth) is one of the important essential oil-producing plant, contributes more than 50% of total exports of Indonesia’s essential oil. However, the extraction of patchouli oil that has been done in Indonesia is generally still used conventional methods that require enormous amount of energy, high solvent usage, and long time of extraction. Therefore, in this study, patchouli oil extraction was carried out by using microwave hydrodistillation and solvent-free microwave extraction methods. Based on this research, it is known that the extraction of patchouli oil using microwave hydrodistillation method with longer extraction time (240 min) only produced patchouli oil’s yield 1.2 times greater than solvent-free microwave extraction method which require faster extraction time (120 min). Otherwise the analysis of electric consumption and the environmental impact, the solvent-free microwave extraction method showed a smaller amount when compared with microwave hydrodistillation method. It is conclude that the use of solvent-free microwave extraction method for patchouli oil extraction is suitably method as a new green technique.

  17. effect of crude oil extracts on early stages of african catfish

    African Journals Online (AJOL)

    Admin

    Nigerian Bonny light crude oil and Exxon Mobil Oso off-shore condensate during a ... of Oso condensate extract when larval integument was damaged. It is ... Spills of oil condensate from Oso Exxon Mobil Oil rig readily enter the .... compounds are extracted from oil films in natural .... Resources and Fishing Rome, 9-13 Dec.

  18. Application of molecular sieves in the fractionation of lemongrass oil from high-pressure carbon dioxide extraction

    Directory of Open Access Journals (Sweden)

    L. Paviani

    2006-06-01

    Full Text Available The aim of this work was to study the feasibility of simultaneous process of high-pressure extraction and fractionation of lemongrass essential oil using molecular sieves. For this purpose, a high-pressure laboratory-scale extraction unit coupled with a column with four different stationary phases for fractionation: ZSM5 zeolite, MCM-41 mesoporous material, alumina and silica was employed. Additionally, the effect of carbon dioxide extraction variables on the global yield and chemical composition of the essential oil was also studied in a temperature range of 293 to 313 K and a pressure range of 100 to 200 bar. The volatile organic compounds of the extracts were identified by a gas chromatograph coupled with a mass spectrometer detector (GC/MS. The results indicated that the extraction process variables and the stationary phase exerted an effect on both the extraction yield and the chemical composition of the extracts.

  19. Determining an Efficient Solvent Extraction Parameters for Re-Refining of Waste Lubricating Oils

    Directory of Open Access Journals (Sweden)

    Hassan Ali Durrani

    2012-04-01

    Full Text Available Re-refining of vehicle waste lubricating oil by solvent extraction is one of the efficient and cheapest methods. Three extracting solvents MEK (Methyl-Ethyl-Ketone, 1-butanol, 2-propanol were determined experimentally for their performance based on the parameters i.e. solvent type, solvent oil ratio and extraction temperature. From the experimental results it was observed the MEK performance was highest based on the lowest oil percent losses and highest sludge removal. Further, when temperature of extraction increased the oil losses percent also decreased. This is due to the solvent ability that dissolves the base oil in waste lubricating oil and determines the best SOR (Solvent Oil Ratio and extraction temperatures.

  20. Near-Infrared Spectroscopy Combined with Multivariate Calibration to Predict the Yield of Sesame Oil Produced by Traditional Aqueous Extraction Process

    Directory of Open Access Journals (Sweden)

    Yong-Dong Xu

    2017-01-01

    Full Text Available Sesame oil produced by the traditional aqueous extraction process (TAEP has been recognized by its pleasant flavor and high nutrition value. This paper developed a rapid and nondestructive method to predict the sesame oil yield by TAEP using near-infrared (NIR spectroscopy. A collection of 145 sesame seed samples was measured by NIR spectroscopy and the relationship between the TAEP oil yield and the spectra was modeled by least-squares support vector machine (LS-SVM. Smoothing, taking second derivatives (D2, and standard normal variate (SNV transformation were performed to remove the unwanted variations in the raw spectra. The results indicated that D2-LS-SVM (4000–9000 cm−1 obtained the most accurate calibration model with root mean square error of prediction (RMSEP of 1.15 (%, w/w. Moreover, the RMSEP was not significantly influenced by different initial values of LS-SVM parameters. The calibration model could be helpful to search for sesame seeds with higher TAEP oil yields.

  1. Effect of irradiation and extractive solvents on the Thevetia seed oil ...

    African Journals Online (AJOL)

    Oil of irradiated thevetia seeds was extracted with different solvents. The effect of irradiation dosages on the extracted oils was studied by comparing the TLC chromatography of irradiated seed oil with that of non-radiated seeds. Saponification values were also compared.

  2. Process design for isolation of soybean oil bodies by applying the product-driven process synthesis methodology

    NARCIS (Netherlands)

    Zderic, A.; Taraksci, T.; Hooshyar, N.; Zondervan, E.; Meuldijk, J.

    2014-01-01

    The present work describes the product driven process synthesis (PDPS) methodology for the conceptual design of extraction of intact oil bodies from soybeans. First, in this approach consumer needs are taken into account and based on these needs application of the final product (oil bodies) is

  3. Enhancement of Palm Oil Extraction Using Cell Wall Degrading Enzyme Formulation

    International Nuclear Information System (INIS)

    Silvamany, H.; Jamaliah Md Jahim

    2015-01-01

    In this recent work, application of aqueous enzymatic process to enhance recovery of palm oil was studied. Experiments were carried out to investigate the structural carbohydrate composition of oil palm mesocarp (Elaeis guineensis) and to analyze the effect of different combination of enzymes on the palm oil recovery and degree of digestibility and the respective correlation. The optimum combination of enzymes comprising of Cellic CTec2 (X 1 ), Cellic HTec2 (X 2 ) and Pectinex Ultra SP-L (X 3 ) for Aqueous Enzymatic Oil Extraction Process (AEOEP), were determined using Simplex Lattice mixture design under fixed parameters. Maximum oil recovery of 88 % was achieved with ratio of enzymes at 0.46: 0.34: 0.2 (X 1 :X 2 :X 3 ), at enzyme loading of 30 mg protein/ 10 g substrate, substrate loading of 50 % w/v, pH 4.8, and 2 hours of incubation at 50 degree Celsius. The conversion of reducing sugar at corresponding condition was measured to evaluate the effectiveness of enzymes in degrading fruit cell wall releasing trapped oil. Moreover, transmission electron microscopy (TEM) was utilized to indicate the increase in cell wall disintegration leading to higher release of oil with enzymatic treatment. (author)

  4. Ultrasound pretreatment as an alternative to improve essential oils extraction

    Directory of Open Access Journals (Sweden)

    Flávia Michelon Dalla Nora

    Full Text Available ABSTRACT: Essential oils are substances originated from plants in general. These compounds are well known to have a high biological activity, specially the antioxidant and antimicrobial. Several extraction techniques are employed to obtain these substances. However, the majority of these techniques require a long extraction time. In this sense, innovative and alternative extraction techniques, such as ultrasound, have recently been the target of studies. In view of the small amount of publications using ultrasonic pretreatment, this review aimed to congregate current relevant information on ultrasound-assisted extraction of essential oils. In this sense, theoretical aspects, such as the main factors that influence the performance of this technique as well as the advantages and disadvantages of the use of ultrasound as an environmental friendly alternative technique to improve the extraction of essential oil in comparison to traditional methods, are shown. Considering the available studies in the literature on essential oil extraction using ultrasonic pretreatment, low frequencies ranged from 20 to 50kWz and times ranged from 20 to 40min were used. The use of ultrasonic pretreatment represents a time reduction to near 70% in relation to the conventional hydrodistillation. Also, these conditions enabled a growth in the extraction of bioactive compounds and consequently improving the antioxidant and antimicrobial activities of essential oils.

  5. An energy-saving opportunity in producing lubricating oil using mixed-solventin simulated Rotary Disc Contacting (RDC) extraction tower

    Energy Technology Data Exchange (ETDEWEB)

    Hatamipour, M.S.; Fakhr Hoseini, S.M.; Tavakkoli, T.; Mehrkesh, A.H. [Chemical Engineering Department, University of Isfahan, Isfahan (Iran)

    2010-05-15

    Industrial processes are the most energy consuming processes in the world. Modification of these processes helps us with controlling the consumption of energy and minimizing energy loss. Changing raw materials is one of the ways through which we can optimize industrial processes. In this paper, a new solvent mixture (furfural + a co-solvent) was used for the extraction of lubricating base oil from lube-oil cut. It was found that the energy consumption of the new solvent mixture for obtaining a product with the same quality was much lower than the original solvent. By using this new solvent mixture, the operating temperature of the top of tower was reduced by 30 K. This leads to a high reduction in energy consumption in extraction of aromatics from lube oil. At our new extraction process by means of using new solvent mixture, the maximum energy saving was 38% per cubic meter of produced raffinate. (author)

  6. Effect of clay content in rock on oil extraction under alkaline seam conditions

    Energy Technology Data Exchange (ETDEWEB)

    Vezirov, D Sh; Gorbunov, A T; Kasimov, Sh A; Kashchavtsev, V E; Tairov, N D

    1978-01-01

    When oil beds are flooded with alkaline solutions, the alkaline concentration in the solution can be significantly reduced as a result of the interaction between clay and alkali. Large losses of alkali in the bed can render the flooding method ineffective. Experimental studies were conducted on porous media containing up to 25% clay at a constant permeability of 1 D in order to determine the oil extraction indices for clay-containing rock. Constant permeability is maintained by using clays, marshalite, and quartz sand in various proportions. Oil having a viscosity of 99.17 sP, and containing a large amount of surfactants, including 1.1% naphthenic acid, was extracted by fresh water and a 0.25% solution of NaOH. The extraction of oil by fresh water and NaOH solution from quartz sand indicated the advantage of using alkaline solutions. The extraction coefficient increased by 11% with the use of this method. As clay is added to the sand, the extraction coefficient decreases, and is reduced to 12.7% when the clay content reaches 25%. Nevertheless, a comparison of data obtained for quartz sand with fresh water on a porous medium containing 25% clay with an alkaline solution, indicates that the extraction coefficient is just 1.5% lower even in the presence of such a large amount of clay. Consequently, alkaline flooding should still be given preference over the usual methods under specific conditions and where the rock has a comparatively large amount of clay, in view of all the basic factors that influence the extraction process. The results obtained can be used for selecting alkaline concentration in evaluating the efficiency of flooding oil beds with alkaline solutions. 2 figures, 2 tables.

  7. The integral and extrinsic bioactive proteins in the aqueous extracted soybean oil bodies.

    Science.gov (United States)

    Zhao, Luping; Chen, Yeming; Cao, Yanyun; Kong, Xiangzhen; Hua, Yufei

    2013-10-09

    Soybean oil bodies (OBs), naturally pre-emulsified soybean oil, have been examined by many researchers owing to their great potential utilizations in food, cosmetics, pharmaceutical, and other applications requiring stable oil-in-water emulsions. This study was the first time to confirm that lectin, Gly m Bd 28K (Bd 28K, one soybean allergenic protein), Kunitz trypsin inhibitor (KTI), and Bowman-Birk inhibitor (BBI) were not contained in the extracted soybean OBs even by neutral pH aqueous extraction. It was clarified that the well-known Gly m Bd 30K (Bd 30K), another soybean allergenic protein, was strongly bound to soybean OBs through a disulfide bond with 24 kDa oleosin. One steroleosin isoform (41 kDa) and two caleosin isoforms (27 kDa, 29 kDa), the integral bioactive proteins, were confirmed for the first time in soybean OBs, and a considerable amount of calcium, necessary for the biological activities of caleosin, was strongly bound to OBs. Unexpectedly, it was found that 24 kDa and 18 kDa oleosins could be hydrolyzed by an unknown soybean endoprotease in the extracted soybean OBs, which might give some hints for improving the enzyme-assisted aqueous extraction processing of soybean free oil.

  8. development of u-channel screw jack for vegetable oil extraction

    African Journals Online (AJOL)

    HOD

    the performance of the machine in terms of oil yield, extraction efficiency and extraction loss with groundnut as the feedstock. ... The world production of oil seed stocks was estimated to ..... published by Asoke K. Ghosh PHI Learning. Limited ...

  9. Review of Palm Kernel Oil Processing And Storage Techniques In South East Nigeria

    Directory of Open Access Journals (Sweden)

    Okeke CG

    2017-06-01

    Full Text Available An assessment of palm kernel processing and storage in South-Eastern Nigeria was carried out by investigative survey approach. The survey basically ascertained the extent of mechanization applicable in the area to enable the palm kernel processors and agricultural policy makers, device the modalities for improving palm kernel processing in the area. According to the results obtained from the study, in Abia state, 85% of the respondents use mechanical method while 15% use manual method in cracking their kernels. In Imo state, 83% of the processors use mechanical method while 17% use manual method. In Enugu and Ebonyi state, 70% and 50% of the processors respectively use mechanical method. It is only in Anambra state that greater number of the processors (50% use manual method while 45% use mechanical means. It is observable from the results that palm kernel oil extraction has not received much attention in mechanization. The ANOVA of the palm kernel oil extraction technique in South- East Nigeria showed significant difference in both the study area and oil extraction techniques at 5% level of probability. Results further revealed that in Abia State, 70% of the processors use complete fractional process in refining the palm kernel oil; 25% and 5% respectively use incomplete fractional process and zero refining process. In Anambra, 60% of the processors use complete fractional process and 40% use incomplete fractional process. Zero refining method is not applicable in Anambra state. In Enugu sate, 53% use complete fractional process while 25% and 22% respectively use zero refining and incomplete fractional process in refining the palm kernel oil. Imo state, mostly use complete fractional process (85% in refining palm kernel oil. About 10% use zero refining method while 5% of the processors use incomplete fractional process. Plastic containers and metal drums are dominantly used in most areas in south-east Nigeria for the storage of palm kernel oil.

  10. Green Soap: An Extraction and Saponification of Avocado Oil

    Science.gov (United States)

    Sutheimer, Susan; Caster, Jacqueline M.; Smith, Simone H.

    2015-01-01

    An introductory level green chemistry experiment is described that places a new twist on soap-making in lab. In this experiment, oil is extracted from an avocado, after which the oil is saponified to produce bars of green craft soap. Commonly used extraction solvents, such as petroleum ether, methylene chloride, and hexane, are replaced with safer…

  11. Efficiency of the refining processes in removing 14C-dichlorvos residues in soybean oil

    International Nuclear Information System (INIS)

    Soliman, S.M.

    2006-01-01

    Crude soybean oil extracted from grains treated with 14 C-dichlorvos at a dose 24 mg insecticide / kg seeds and stored for 30 weeks was subjected to different refining processes such as alkali treatment, bleaching, winterization and deodorization. The effect of the refining processes on the nature and magnitude of the originally present residues was investigated. The insecticide residues in crude oil and cake amounted to 9.5% and 55% , respectively, of original residues inside the seeds. Extraction of the seeds with hexane gave crude oil with 9.5 % of original residues in seeds. The l4 C-activity in the crude stored Soya beans oil could be reduced by about 82% of radioactivity originally present in crude oil eliminated by simulated commercial processes locally used for oil refining. A high percentage of the residues (50-55%) were eliminated during alkali treatment and bleaching. Refining of soybeans oil fortified with '1 4 C-dichlorovos. The final refined oil had only 13% of the radioactivity originally present, mainly in the form of dichlorvos, dimethyl and monomethyl phosphate in addition to desmethyl dichlorvos in oil with aged residues

  12. Effect of irradiation and extractive solvents on the Thevetia seed oil

    African Journals Online (AJOL)

    STORAGESEVER

    2009-03-06

    Mar 6, 2009 ... Oil of irradiated thevetia seeds was extracted with different solvents. The effect of irradiation dosages on the extracted oils was studied by comparing the TLC chromatography of irradiated seed oil with that of non-radiated seeds. Saponification values were also compared. Key words: Thevetia seed, ...

  13. Process intensification for biodiesel production from Jatropha curcas L. seeds: Supercritical reactive extraction process parameters study

    International Nuclear Information System (INIS)

    Lim, Steven; Lee, Keat Teong

    2013-01-01

    Highlights: ► Investigation of supercritical reactive extraction process for biodiesel production. ► Focus is given on optimizing methyl esters yield for Jatropha curcas L. seeds. ► Influence of process parameters to the reaction are discussed thoroughly. ► Comparison between the novel reaction with conventional process are studied. ► High methyl esters yield can be obtained without pre-extraction and catalyst. -- Abstract: In a bid to increase the cost competitiveness of biodiesel production against mineral diesel, process intensification has been studied for numerous biodiesel processing technologies. Subsequently, reactive extraction or in situ transesterification is actively being explored in which the solid oil-bearing seeds are used as the reactant directly with short-chain alcohol. This eliminates separate oil extraction process and combines both extraction and transesterification in a single unit. Supercritical reactive extraction takes one step further by substituting the role of catalyst with supercritical conditions to achieve higher yield and shorter processing time. In this work, supercritical reactive extraction with methanol was carried out in a high-pressure batch reactor to produce fatty acid methyl esters (FAMEs) from Jatropha curcas L. seeds. Material and process parameters including space loading, solvent to seed ratio, co-solvent (n-hexane) to seed ratio, reaction temperature, reaction time and mixing intensity were varied one at a time and optimized based on two responses i.e. extraction efficiency, M extract and FAME yield, F y . The optimum responses for supercritical reactive extraction obtained were 104.17% w/w and 99.67% w/w (relative to 100% lipid extraction with n-hexane) for M extract and F y respectively under the following conditions: 54.0 ml/g space loading, 5.0 ml/g methanol to seeds ratio, 300 °C, 9.5 MPa (Mega Pascal), 30 min reaction time and without n-hexane as co-solvent or any agitation source. This proved that

  14. Extraction of essential oils from Algerian myrtle leaves using instant controlled pressure drop technology.

    Science.gov (United States)

    Berka-Zougali, Baya; Hassani, Aicha; Besombes, Colette; Allaf, Karim

    2010-10-01

    In the present work, the new extraction process of Détente Instantanée Contrôlée DIC (French, for instant controlled pressure drop) was studied, developed, quantitatively and qualitatively compared to the conventional hydrodistillation method for the extraction of essential oils from Algerian myrtle leaves. DIC was used as a thermomechanical treatment, DIC subjecting the product to a high-pressure saturated steam. The DIC cycle ends with an abrupt pressure drop towards vacuum, and this instantly leads to an autovaporization of myrtle volatile compounds. An immediate condensation in the vacuum tank produced a micro-emulsion of water and essential oils. Thus, an ultra-rapid cooling of residual leaves occurred, precluding any thermal degradation. An experimental protocol was designed with 3 independent variables: saturated steam pressure between 0.1 and 0.6 MPa, resulting in a temperature between 100 and 160°C, a total thermal processing time between 19 and 221 s, and between 2 and 6 DIC cycles. The essential oils yield was defined as the main dependent variable. This direct extraction gave high yields and high quality essential oil, as revealed by composition and antioxidant activity (results not shown). After this treatment, the myrtle leaves were recovered and hydrodistilled in order to quantify the essential oil content in residual DIC-treated samples. Scanning electron microscope (SEM) showed some modification of the structure with a slight destruction of cell walls after DIC treatment. Copyright © 2010 Elsevier B.V. All rights reserved.

  15. Antioxidant activity for spice oils (1) anti oxidative stability of thyme and caraway oil extracts under UV-irradiation

    International Nuclear Information System (INIS)

    Atef Ghazy, M.; Shaker, E.S.

    2002-01-01

    The anti oxidative activity for some spice essential oils have been investigated using thiocyanate method and compared with common natural antioxidant. The antioxidant activity for nine spice oils has been measured at 500 ppm after 13 days. The most potent one was the lemon grass (99.8), followed by orange peel, thyme, and caraway. The activities for these four oils were higher than that for Alpha-tocopherol (87.7%). Petitgrain, and geranium oils have marched activity but less than that for Alpha-tocopherol. No obvious has been found for citronella. fennel, and cardamon oils. The aqueous, butanoic, methanolic and hexanoic extracts for thyme and caraway oil exhibit effective anti oxidative activities under UV irradiation (254 nm) for 6 and 10 hr compared with that for alpha-tocopherol. The anti oxidative effect of thyme and caraway oil extracts were found to be strong and stable towards UV-irradiation, and equal to that for Alpha-tocopherol. Thyme's aqueous and caraway's hexanal extracts were the most potent extracts under the same conditions

  16. Application of enzymatic methods for chia (Salvia hispanica L oil extraction

    Directory of Open Access Journals (Sweden)

    Norma Ciau-Solís

    2016-07-01

    Full Text Available Aim. The aim was to evaluate the use of different enzymatic treatments on the oil extraction yield from Chia (Salvia hispanica L. seeds Methods. Enzymatic extraction was performed by treating of whole and degummed chia flours with different conditions of enzyme concentration, pH and temperature. Commercial enzymes were employed: Viscozyme LTM (endo-1,3 (4-betaglucanase derived from Aspergillus aculeatus, with 100 FBG g (Beta Glucanase-unit Fungal and Neutrase0.8LTM, neutral protease with 0.8 AU-NH/g of activity, derived from Bacillus amyloliquefaciens. Results. All treatments of enzymatic oil extraction were different (P <0.05 and the maximum oil yield obtained was 9.35%. Conclusion. Oil extraction using enzymatic methods is not a viable for chia seed

  17. Dual-fuel production from restaurant grease trap waste: bio-fuel oil extraction and anaerobic methane production from the post-extracted residue.

    Science.gov (United States)

    Kobayashi, Takuro; Kuramochi, Hidetoshi; Maeda, Kouji; Tsuji, Tomoya; Xu, Kaiqin

    2014-10-01

    An effective way for restaurant grease trap waste (GTW) treatment to generate fuel oil and methane by the combination of physiological and biological processes was investigated. The heat-driven extraction could provide a high purity oil equivalent to an A-grade fuel oil of Japanese industrial standard with 81-93 wt% of extraction efficiency. A post-extracted residue was treated as an anaerobic digestion feedstock, and however, an inhibitory effect of long chain fatty acid (LCFA) was still a barrier for high-rate digestion. From the semi-continuous experiment fed with the residual sludge as a single substrate, it can be concluded that the continuous addition of calcium into the reactor contributed to reducing LCFA inhibition, resulting in the long-term stable operation over one year. Furthermore, the anaerobic reactor performed well with 70-80% of COD reduction and methane productivity under an organic loading rate up to 5.3g-COD/L/d. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Extraction and characterization of radish seed oils using different ...

    African Journals Online (AJOL)

    However, SCE oil had the best oxidative stability, and highest contents of vitamin ... that consumption of radish (Raphanus sativus L.) has positive ... rate of liquid CO2 was 35 L/h. The oil in the .... amounts of toxic solvents to extract plant oils.

  19. A comparative study of solvent and supercritical Co2 extraction of Simarouba gluaca seed oil

    International Nuclear Information System (INIS)

    Anjaneyulu, B.; Satyannarayana, S.; Kanjilal, S.; Siddaiah, V.; Prasanna Rani, K.N.

    2017-01-01

    In the present study, the supercritical carbon dioxide (Co2) extraction of oil from Simarouba gluaca seeds was carried out at varying conditions of pressure (300–500 bar), temperature (50–70 °C) and CO2 flow rate (10–30 g·min-1). The extraction condition for maximum oil yield was obtained at 500 bar pressure, 70 °C and at 30 g·min-1 flow rate of CO2. The extracted oil was analyzed thoroughly for physico-chemical properties and compared with those of conventional solvent extracted oil. An interesting observation is a significant reduction in the phosphorus content of the oil (8.4 mg·kg-1) extracted using supercritical CO2 compared to the phosphorous content of the solvent extracted oil (97 mg·kg-1). Moreover, the content of total tocopherols in supercritically extracted oil (135.6 mg·kg-1) was found to be higher than the solvent extracted oil (111 mg·kg-1). The rest of the physico-chemical properties of the two differently extracted oils matched well with each other. The results indicated the possible benefits of supercritical CO2 extraction over solvent extraction of Simarouba gluaca seed oil. [es

  20. A comparative study of solvent and supercritical CO2 extraction of Simarouba gluaca seed oil

    Directory of Open Access Journals (Sweden)

    B. Anjaneyulu

    2017-09-01

    Full Text Available In the present study, the supercritical carbon dioxide (CO2 extraction of oil from Simarouba gluaca seeds was carried out at varying conditions of pressure (300–500 bar, temperature (50–70 °C and CO2 flow rate (10–30 g·min-1. The extraction condition for maximum oil yield was obtained at 500 bar pressure, 70 °C and at 30 g·min-1 flow rate of CO2. The extracted oil was analyzed thoroughly for physico-chemical properties and compared with those of conventional solvent extracted oil. An interesting observation is a significant reduction in the phosphorus content of the oil (8.4 mg·kg-1 extracted using supercritical CO2 compared to the phosphorous content of the solvent extracted oil (97 mg·kg-1. Moreover, the content of total tocopherols in supercritically extracted oil (135.6 mg·kg-1 was found to be higher than the solvent extracted oil (111 mg·kg-1. The rest of the physico-chemical properties of the two differently extracted oils matched well with each other. The results indicated the possible benefits of supercritical CO2 extraction over solvent extraction of Simarouba gluaca seed oil.

  1. Alternative Bio-Based Solvents for Extraction of Fat and Oils: Solubility Prediction, Global Yield, Extraction Kinetics, Chemical Composition and Cost of Manufacturing

    Directory of Open Access Journals (Sweden)

    Anne-Gaëlle Sicaire

    2015-04-01

    Full Text Available The present study was designed to evaluate the performance of alternative bio-based solvents, more especially 2-methyltetrahydrofuran, obtained from crop’s byproducts for the substitution of petroleum solvents such as hexane in the extraction of fat and oils for food (edible oil and non-food (bio fuel applications. First a solvent selection as well as an evaluation of the performance was made with Hansen Solubility Parameters and the COnductor-like Screening MOdel for Realistic Solvation (COSMO-RS simulations. Experiments were performed on rapeseed oil extraction at laboratory and pilot plant scale for the determination of lipid yields, extraction kinetics, diffusion modeling, and complete lipid composition in term of fatty acids and micronutrients (sterols, tocopherols and tocotrienols. Finally, economic and energetic evaluations of the process were conducted to estimate the cost of manufacturing using 2-methyltetrahydrofuran (MeTHF as alternative solvent compared to hexane as petroleum solvent.

  2. Optimization of Pumpkin Oil Recovery by Using Aqueous Enzymatic Extraction and Comparison of the Quality of the Obtained Oil with the Quality of Cold-Pressed Oil

    Science.gov (United States)

    Roszkowska, Beata; Czaplicki, Sylwester; Tańska, Małgorzata

    2016-01-01

    Summary The study was carried out to optimize pumpkin oil recovery in the process of aqueous extraction preceded by enzymatic maceration of seeds, as well as to compare the quality of the obtained oil to the quality of cold-pressed pumpkin seed oil. Hydrated pulp of hulless pumpkin seeds was macerated using a 2% (by mass) cocktail of commercial pectinolytic, cellulolytic and proteolytic preparations (Rohapect® UF, Rohament® CL and Colorase® 7089). The optimization procedure utilized response surface methodology based on Box- -Behnken plan of experiment. The optimized variables of enzymatic pretreatment were pH, temperature and maceration time. The results showed that the pH value, temperature and maceration time of 4.7, 54 °C and 15.4 h, respectively, were conducive to maximize the oil yield up to 72.64%. Among these variables, the impact of pH was crucial (above 73% of determined variation) for oil recovery results. The oil obtained by aqueous enzymatic extraction was richer in sterols, squalene and tocopherols, and only slightly less abundant in carotenoids than the cold-pressed one. However, it had a lower oxidative stability, with induction period shortened by approx. 30% in relation to the cold-pressed oil. PMID:28115898

  3. Optimization of Pumpkin Oil Recovery by Using Aqueous Enzymatic Extraction and Comparison of the Quality of the Obtained Oil with the Quality of Cold-Pressed Oil

    Directory of Open Access Journals (Sweden)

    Beata Roszkowska

    2016-01-01

    Full Text Available The study was carried out to optimize pumpkin oil recovery in the process of aqueous extraction preceded by enzymatic maceration of seeds, as well as to compare the quality of the obtained oil to the quality of cold-pressed pumpkin seed oil. Hydrated pulp of hulless pumpkin seeds was macerated using a 2 % (by mass cocktail of commercial pectinolytic, cellulolytic and proteolytic preparations (Rohapect® UF, Rohament® CL and Colorase® 7089. The optimization procedure utilized response surface methodology based on Box-Behnken plan of experiment. The optimized variables of enzymatic pretreatment were pH, temperature and maceration time. The results showed that the pH value, temperature and maceration time of 4.7, 54 °C and 15.4 h, respectively, were conducive to maximize the oil yield up to 72.64 %. Among these variables, the impact of pH was crucial (above 73 % of determined variation for oil recovery results. The oil obtained by aqueous enzymatic extraction was richer in sterols, squalene and tocopherols, and only slightly less abundant in carotenoids than the cold-pressed one. However, it had a lower oxidative stability, with induction period shortened by approx. 30 % in relation to the cold-pressed oil.

  4. Data set for extraction and transesterification of bio-oil from Stoechospermum marginatum, a brown marine algae.

    Science.gov (United States)

    Venkatesan, Hariram; Godwin, John J; Sivamani, Seralathan

    2017-10-01

    The article presents the experimental data on the extraction and transesterification of bio-oil derived from Stoechospermum marginatum, a brown macro marine algae. The samples were collected from Mandapam region, Gulf of Mannar, Tamil Nadu, India. The bio-oil was extracted using Soxhlet technique with a lipid extraction efficiency of 24.4%. Single stage transesterification was adopted due to lower free fatty acid content. The yield of biodiesel was optimized by varying the process parameters. The obtained data showed the optimum process parameters as reaction time 90 min, reaction temperature 65 °C, catalyst concentration 0.50 g and 8:1 M ratio. Furthermore, the data pertaining to the physio-chemical properties of the derived algal biodiesel were also presented.

  5. Data set for extraction and transesterification of bio-oil from Stoechospermum marginatum, a brown marine algae

    Directory of Open Access Journals (Sweden)

    Hariram Venkatesan

    2017-10-01

    Full Text Available The article presents the experimental data on the extraction and transesterification of bio-oil derived from Stoechospermum marginatum, a brown macro marine algae. The samples were collected from Mandapam region, Gulf of Mannar, Tamil Nadu, India. The bio-oil was extracted using Soxhlet technique with a lipid extraction efficiency of 24.4%. Single stage transesterification was adopted due to lower free fatty acid content. The yield of biodiesel was optimized by varying the process parameters. The obtained data showed the optimum process parameters as reaction time 90 min, reaction temperature 65 °C, catalyst concentration 0.50 g and 8:1 M ratio. Furthermore, the data pertaining to the physio-chemical properties of the derived algal biodiesel were also presented.

  6. Acute Toxicity of Castor Oil Bean Extract and Tolerance Level of ...

    African Journals Online (AJOL)

    The experiment was carried out to determine the acute toxicity of raw castor oil bean (Ricinus communis) extract and the tolerance level of raw castor oil bean by broilers. The seeds were ground, defatted with petroleum ether and the residue was subjected to extraction with phosphate-buffered saline. The extract volume ...

  7. First stage of bio-jet fuel production: non-food sunflower oil extraction using cold press method

    Directory of Open Access Journals (Sweden)

    Xianhui Zhao

    2014-06-01

    Full Text Available As a result of concerning petroleum price increasing and environmental impact, more attention is attracted to renewable resources for transportation fuels. Because not conflict with human and animal food resources, non-food vegetable oils are promising sources for developing bio-jet fuels. Extracting vegetable oil from oilseeds is the first critical step in the pathway of bio-jet fuel production. When sunflower seeds are de-hulled, there are always about 5%–15% broken seed kernels (fine meat particles left over as residual wastes with oil content up to 48%. However, the oil extracted from these sunflower seed residues is non-edible due to its quality not meeting food standards. Genetically modified sunflower grown on margin lands has been identified one of sustainable biofuel sources since it doesn't compete to arable land uses. Sunflower oils extraction from non-food sunflower seeds, sunflower meats, and fine sunflower meats (seed de-hulling residue was carried out using a cold press method in this study. Characterization of the sunflower oils produced was performed. The effect of cold press rotary frequency on oil recovery and quality was discussed. The results show that higher oil recovery was obtained at lower rotary frequencies. The highest oil recovery for sunflower seeds, sunflower meats, and fine sunflower meats in the tests were 75.67%, 89.74% and 83.19% respectively. The cold press operating conditions had minor influence on the sunflower oil quality. Sunflower meat oils produced at 15 Hz were preliminarily upgraded and distilled. The properties of the upgraded sunflower oils were improved. Though further study is needed for the improvement of processing cost and oil recovery, cold press has shown promising to extract oil from non-food sunflower seeds for future bio-jet fuel production.

  8. Subcritical Water Extraction of Monosaccharides from Oil Palm Fronds Hemicelluloses

    International Nuclear Information System (INIS)

    Norsyabilah, R.; Hanim, S.S.; Norsuhaila, M.H.; Noraishah, A.K.; Siti Kartina

    2013-01-01

    Oil palm plantations in Malaysia generate more than 36 million tones of pruned and felled oil palm fronds (OPF) and are generally considered as waste. The composition of monosaccharide in oil palm frond can be extracted using hydrothermal treatment for useful applications. The objectives of this study were to quantify the yield of monosaccharides at various reaction conditions; temperature 170 to 200 degree Celsius, pressure from 500 psi to 800 psi, reaction time from 5 to 15 min using subcritical water extraction and to determine the composition of oil palm frond hemicelluloses at optimum condition. The monosaccharides composition of oil palm frond hemicelluloses were analysed using High Performance Liquid Chromatography (HPLC). The highest yield of monosaccharides can be extracted from OPF at temperature of 190 degree Celsius, pressure of 600 psi and 10 min of contact time which is xylose the most abundant composition (11.79 %) followed with arabinose (2.82 %), glucose (0.61 %) and mannose (0.66 %). (author)

  9. Low cost and conformal microwave water-cut sensor for optimizing oil production process

    KAUST Repository

    Karimi, Muhammad Akram

    2015-01-01

    Efficient oil production and refining processes require the precise measurement of water content in oil (i.e., water-cut) which is extracted out of a production well as a byproduct. Traditional water-cut (WC) laboratory measurements are precise

  10. Improved rapeseed oil extraction yield and quality via cold separation of ethanol miscella

    Directory of Open Access Journals (Sweden)

    Citeau Morgane

    2018-03-01

    Full Text Available In the extraction of vegetable oils, the idea of using ethanol as a solvent, allowing solvent recycling without distillation, can be attested as early as 1948 (Beckel, yet it is now seldom envisaged. The development of organic farming and a growing demand for a more natural diet prompted us to revisit this approach, which takes advantage of the relatively low affinity of ethanol for lipids to produce pure crude oils and meal with higher protein content. This method is based on the change of oil solubility in ethanol with temperature. Rapeseed oil extraction was carried out by hot pressurized ethanol (subcritical extraction condition. Oil was then recovered by cooling the miscella and demixing of two phases, an oil-rich phase and a solvent-rich phase. This study, after verifying the kinetics of extraction, focused on the optimization of the demixing temperature based on the amount and quality of recovered oil. The results show that ethanol extraction followed by cold demixing of the miscella makes it possible to obtain a high quality oil, free of free fatty acids and phospholipids.

  11. In vitro antimicrobial activity of Pistacia lentiscus L. edible oil and phenolic extract.

    Science.gov (United States)

    Mezni, F; Aouadhi, C; Khouja, M L; Khaldi, A; Maaroufi, A

    2015-01-01

    Pistacia lentiscus L. is known in some Tunisian forest area by its fixed oil used in traditional medicine as an antiseptic product. This investigation is the first to study the antimicrobial activity of P.lentiscus edible oil and its phenolic extract. Oil was extracted from fruits harvested from six provenances located in Tunisia. The antimicrobial activity was tested using disc diffusion assay and the broth dilution method. Kbouch and Sidi Zid oils were most efficient (p oil and extract.

  12. Effect of ultrasound on olive oil extraction and optimization of ultrasound-assisted extraction of extra virgin olive oil by response surface methodology (RSM)

    International Nuclear Information System (INIS)

    Aydar, A.Y.; Bağdatlıoğlu, N.; Köseoğlu, O.

    2017-01-01

    In this study, the effects of different extraction parameters including ultrasound time, temperature and malaxation time on olive oil quality were investigated. The extraction variables ultrasound initial temperature (20–50 °C), ultrasound time (2–10 min) and malaxation time (30–50 min) were studied to obtain ideal conditions of ultrasonic treatment on the olive paste for obtaining of a greater yield in the extraction of oil, while maintaining a maximum level of commercial quality. To evaluate the level of commercial quality, absorbance in the UV region, peroxide (PV) and free acidity values (AV), the total chlorophyll, carotenoid, phenol contents, total antioxidant activity and sensory analysis of EVOOs extracted from Edremit cultivar were determined. The optimum conditions were found to be 50 °C, 2 min and 43.23 min for ultrasound initial temperature, sonication time and malaxation time, respectively. This optimal condition gave an extraction yield of 8.25 % and the acidity value of 0.24 mg oleic acid/100 g olive oil. The experimental values obtained under optimal conditions were in agreement with the theoretical values [es

  13. Fatty acid profile and elemental content of avocado (Persea americana Mill.) oil--effect of extraction methods.

    Science.gov (United States)

    Reddy, Mageshni; Moodley, Roshila; Jonnalagadda, Sreekanth B

    2012-01-01

    Interest in vegetable oil extracted from idioblast cells of avocado fruit is growing. In this study, five extraction methods to produce avocado oil have been compared: traditional solvent extraction using a Soxhlet or ultrasound, Soxhlet extraction combined with microwave or ultra-turrax treatment and supercritical fluid extraction (SFE). Traditional Soxhlet extraction produced the most reproducible results, 64.76 ± 0.24 g oil/100 g dry weight (DW) and 63.67 ± 0.20 g oil/100 g DW for Hass and Fuerte varieties, respectively. Microwave extraction gave the highest yield of oil (69.94%) from the Hass variety. Oils from microwave extraction had the highest fatty acid content; oils from SFE had wider range of fatty acids. Oils from Fuerte variety had a higher monounsaturated: saturated FA ratio (3.45-3.70). SFE and microwave extraction produced the best quality oil, better than traditional Soxhlet extraction, with the least amount of oxidizing metals present. Copyright © Taylor & Francis Group, LLC

  14. Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil

    Directory of Open Access Journals (Sweden)

    Gamel, T. H.

    1999-10-01

    Full Text Available Effect of methanol extracts of rosemary and olive vegetable water on the stability of olive oil and sunflower oil. Methanol phenolic extracts of dry rosemary leaves and olive vegetable water filtrate, in combination with BHA, were added to olive oil (blend of refined and virgin olive oil, 3 to 1 and to sunflower oil and their antioxidant effects under accelerated conditions were evaluated. Accelerated conditions included the oven test (at 63 °C and the conductivity method (Rancimat at 120 °C. Frying process at 180 °C was also applied. The methanol phenolic extracts and the BHA were added to each oil at the following concentrations: 200 ppm rosemary extract; 200 ppm olive vegetable water extract; 100 ppm rosemary extract + 100 ppm BHA; 100 ppm vegetable water extract + 100 ppm BHA and 200 ppm BHA. In general, antioxidant effect of phenolic additives of rosemary and of BHA was in the following order: 200 ppm rosemary extract > 100 ppm rosemary extract + 100 ppm BHA > and 200 ppm BHA. The addition of 200 ppm vegetable water extract and 100 ppm vegetable water extract + 100 ppm BHA exhibited similar antioxidant effect to that of 200 ppm BHA.

    Extractos metanólicos de fenoles de hojas secas de romero y filtrados de agua de vegetación de la aceituna, en combinación con BHA, se añadieron al aceite de oliva (mezcla de aceite de oliva refinado y virgen, 3 a 1 y al aceite de girasol, evaluándose sus efectos antioxidantes usando condiciones aceleradas. Estas condiciones incluyeron el test del horno de oxidación (a 63 °C y el método de conductividad (Rancimat a 120 °C. También se aplicó al proceso de fritura a 180 °C. Los extractos metanólicos de fenoles y el BHA se añadieron a cada aceite en las siguientes concentraciones: 200 ppm de extracto de romero, 200 ppm de extracto de agua de vegetación de la aceituna, 100 ppm de extracto de romero + 100 ppm de BHA, 100 ppm de extracto de agua de vegetación + 100 ppm de BHA y 200 ppm de BHA

  15. Extraction and quantitation of furanic compounds dissolved in oils

    International Nuclear Information System (INIS)

    Koreh, O.; Torkos, K.; Mahara, M.B.; Borossay, J.

    1998-01-01

    Furans are amongst the decomposition products which are generated by the degradation of cellulose in paper. Paper insulation is used in capacitors, cables and transformers. These furans dissolve in the impregnating mineral oil, and a method, involving liquid/liquid extraction, solid phase extraction and high performance liquid chromatography, has been developed to determine the concentration of 2-furfural the most stable compound in oil. The degradation of paper is being examined in order to find correlation between the change in dielectric and mechanical properties and the increase in concentration of 2-furfural in the oil. (author)

  16. Wet separation processes as method to separate limestone and oil shale

    Science.gov (United States)

    Nurme, Martin; Karu, Veiko

    2015-04-01

    Biggest oil shale industry is located in Estonia. Oil shale usage is mainly for electricity generation, shale oil generation and cement production. All these processes need certain quality oil shale. Oil shale seam have interlayer limestone layers. To use oil shale in production, it is needed to separate oil shale and limestone. A key challenge is find separation process when we can get the best quality for all product types. In oil shale separation typically has been used heavy media separation process. There are tested also different types of separation processes before: wet separation, pneumatic separation. Now oil shale industry moves more to oil production and this needs innovation methods for separation to ensure fuel quality and the changes in quality. The pilot unit test with Allmineral ALLJIG have pointed out that the suitable new innovation way for oil shale separation can be wet separation with gravity, where material by pulsating water forming layers of grains according to their density and subsequently separates the heavy material (limestone) from the stratified material (oil shale)bed. Main aim of this research is to find the suitable separation process for oil shale, that the products have highest quality. The expected results can be used also for developing separation processes for phosphorite rock or all others, where traditional separation processes doesn't work property. This research is part of the study Sustainable and environmentally acceptable Oil shale mining No. 3.2.0501.11-0025 http://mi.ttu.ee/etp and the project B36 Extraction and processing of rock with selective methods - http://mi.ttu.ee/separation; http://mi.ttu.ee/miningwaste/

  17. PALM KERNEL OIL SOLUBITY EXAMINATION AND ITS MODELING IN EXTRACTION PROCESS USING SUPERCRITICAL CARBON DIOXIDE

    Directory of Open Access Journals (Sweden)

    Wahyu Bahari Setianto

    2013-11-01

    Full Text Available Application of  supercritical carbon dioxide (SC-CO2 to vegetable oil extraction became an attractive technique due to its high solubility, short extraction time and simple purification. The method is considered as earth friendly technology due to the absence of chemical usage. Solubility of solute-SC-CO2 is an important data for application of the SC-CO2 extraction. In this work, the equilibrium solubility of the palm kernel oil (PKO in SC-CO2 has been examined using extraction curve analysis. The examinations were performed at temperature and pressure ranges of  323.15 K to 353.15 K and 20.7 to 34.5 MPa respectively. It was obtained that the experimental solubility were from 0.0160 to 0.0503 g oil/g CO2 depend on the extraction condition. The experimental solubility data was well correlated with a solvent density based model with absolute percent deviation of 0.96. PENENTUAN KELARUTAN MINYAK INTI KELAPA SAWIT DAN PEMODELAN EKSTRAKSI DENGAN KARBON DIOKSIDA SUPERKRITIK. Sehubungan dengan kelarutan yang tinggi, waktu ekstraksi yang pendek dan pemurnian hasil yang mudah, aplikasi karbon dioksida superkritis (SC-CO2 pada ekstraksi minyak nabati menjadi sebuah teknik ekstraksi yang menarik. Karena tanpa penggunaan bahan kimia, metode ekstraksi ini dianggap sebagai teknologi yang ramah lingkungan. Kelarutan zat terlarut pada SC-CO2 merupakan data yang penting dalam aplikasi SC-CO2 pada proses ekstraksi.  Pada penelitian ini,  kelarutan kesetimbangan dari minyak biji sawit (PKO dalam SC-CO2 telah diuji dengan mengunakan analisa kurva proses ekstraksi. Pengujian kelarutan tersebut dilakukan pada rentang suhu 323,15 K sampai 353,15 K dan rentang tekanan 20,7 MPa sampai 34,5 MPa. Hasil analisa menunjukkan bahwa kelarutan kesetimbangan hasil percobaan  PKO pada SC-CO2 adalah 0.0160 g minyak/g CO2 sampai 0,0503 g minyak/g CO2 tergantung pada kondisi ekstraksi. Data kelarutan kesetimbangan hasil percobaan  telah dikorelasaikan dengan baik menggunakan

  18. Solvent extraction

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, D.M.; Latimer, E.G.

    1988-01-05

    It is an object of this invention to provide for the demetallization and general upgrading of heavy oil via a solvent extracton process, and to improve the efficiency of solvent extraction operations. The yield and demetallization of product oil form heavy high-metal content oil is maximized by solvent extractions which employ either or all of the following techniques: premixing of a minor amount of the solvent with feed and using countercurrent flow for the remaining solvent; use of certain solvent/free ratios; use of segmental baffle tray extraction column internals and the proper extraction column residence time. The solvent premix/countercurrent flow feature of the invention substantially improves extractions where temperatures and pressures above the critical point of the solvent are used. By using this technique, a greater yield of extract oil can be obtained at the same metals content or a lower metals-containing extract oil product can be obtained at the same yield. Furthermore, the premixing of part of the solvent with the feed before countercurrent extraction gives high extract oil yields and high quality demetallization. The solvent/feed ratio features of the invention substanially lower the captial and operating costs for such processes while not suffering a loss in selectivity for metals rejection. The column internals and rsidence time features of the invention further improve the extractor metals rejection at a constant yield or allow for an increase in extract oil yield at a constant extract oil metals content. 13 figs., 3 tabs.

  19. Radiological consequences of gas and oil extraction

    International Nuclear Information System (INIS)

    Kutkov, V.

    2002-01-01

    Contamination of the environment by Technologically Enhanced Naturally Occurring Radioactive Material (TENORM) is a well-known side outcome of gas and oil extraction. Naturally Occurring Radioactive Material (NORM) means material containing the radionuclides of nature origin, i.e., K 40, U 238, Th 232 and their decay products. Technologically Enhanced means, that the physical, chemical, radiological properties, and concentrations of natural radionuclides in NORM have been altered such that there exists a potential for:Redistribution and contamination of environmental media (soil, water, and air); Increased environmental mobility in soils and groundwater; Incorporation of elevated levels of radioactivity in products and construction materials; Improper disposal or use of disposal methods that could result in unnecessary and relatively high exposures to individuals and populations via any environmental pathway and medium. NORM and TENORM are the major sources of human exposure in the World. Their contributions to the worldwide human exposure as evaluated by UNSCEAR. The radiological consequences of occupational and public exposures with TENORM are not clearly monitored and examined. The principal reason of such situation is that for a long time neither ecological organizations nor Regulatory Authorities did not consider the handling of material containing natural radionuclides (other than radon and thoron) as object for regulation of radiation safety. For instance, till now Green peace have not demonstrated any opinion about this problem. TENORM released in oil and gas extraction is a major source of environmental contamination of the Caspian Sea and soils, surface and ground waters in Azerbaijan. The origin of TENORM in oil fields of Apsheron peninsula is related to drilling, production, and processing operations. Other sources of contamination are oil well equipment where separation of contaminated water from oil takes place. Contamination of the environment leads

  20. Effect of unsaponifiable matter extracted from Pistacia khinjuk fruit oil on the oxidative stability of olive oil.

    Science.gov (United States)

    Tavakoli, Javad; Estakhr, Parviz; Jelyani, Aniseh Zarei

    2017-08-01

    The present study was carried out to investigate the improvement of oxidative stability of refined olive oil using various concentrations of unsaponifiable matters extracted from Pistacia khinjuk fruit oil (UFO). For further elucidation of UFO antioxidative power, tertbutylhydroquinone (TBHQ) was used in an olive oil sample, too. Oxidative stability of olive oil samples without and with different levels of UFO (50, 100, 250, 500, 750 and 1000 ppm) and TBHQ (100 ppm) were studied via evaluation of conjugated diene value, carbonyl value, oil/oxidative stability index, acid value and total tocopherol (TT) contents through 8 h thermal process at 170 °C. Results obtained by oxidative stability assays revealed that the highest antioxidative activity of olive oil was obtained by 100 ppm of UFO, followed using 100, 250, 500, 750, and 1000 ppm of UFO and 100 ppm TBHQ, respectively. Evaluation of the relationship between oxidative stability indexes and TT changes indicated a strong correlation (R 2  = 0.9718) between mean relative resistance to oxidation and relative resistance to TT reduction during thermal process. By promotion of relative resistance to TT reduction, olive oil samples' relative resistance to oxidation was enhanced exponentially; implying importance of TT in promotion of oxidative stability of edible oils. The results obtained in this study showed that UFO has higher antioxidative activity compared to TBHQ; thus UFO can be considered as a natural antioxidant with ideal antioxidative activity.

  1. Experimental optimization of catalytic process in-situ for heavy oil and bitumen upgrading

    Energy Technology Data Exchange (ETDEWEB)

    Shah, A.; Fishwick, R.P.; Leeke, G.A.; Wood, J. [Birmingham Univ., Birmingham (United Kingdom); Rigby, S.P.; Greaves, M. [Bath Univ., Bath (United Kingdom)

    2010-07-01

    Peak crude oil production is expected to occur in the second decade of this century, followed by a phase of permanent decline in conventional crude oil production. However, very large resources of heavy oil and bitumen exist throughout the world, most notably in Canada and Venezuela. The high viscosity and density of these non-conventional crude oils require more energy intensive operations for production and upgrading, and also for transportation. As such, they are more costly to extract. This paper described some of the technological innovations that are being considered to extract heavier oil supplies with reduced environmental impact. The toe-to-heel air injection (THAI) process and its catalytic added-on (CAPRI) process combine in-situ combustion with catalytic upgrading using an annular catalyst packed around a horizontal producer well. Results of an experimental study concerning optimization of catalyst type and operating conditions showed that CAPRI can effect further upgrading of partially upgraded THAI oil, with upgrading levels of viscosity and API gravity dependent upon temperature and flow rate. 20 refs., 8 tabs., 10 figs.

  2. Fatty Acid Composition and Antioxidant Activity of Tea (Camellia sinensis L.) Seed Oil Extracted by Optimized Supercritical Carbon Dioxide

    Science.gov (United States)

    Wang, Yuefei; Sun, Da; Chen, Hao; Qian, Lisheng; Xu, Ping

    2011-01-01

    Seeds are another product in addition to leaves (raw materials for teas) of tea (Camellia sinensis L.) plant. The great increase of tea consumption in recent years raises the challenge of finding commercial applications for tea seeds. In the present study, supercritical carbon dioxide (SC-CO2) extraction edible oil from tea seed was carried out, response surface methodology (RSM) was used to optimize processing parameters including time (20–90 min), temperature (35–45 °C) and pressure (50–90 MPa). The fatty acid composition and antioxidant activity of the extracted oil was also investigated. The highest yield of oil (29.2 ± 0.6%) was obtained under optimal SC-CO2 extraction conditions (45 °C, 89.7 min and 32 MPa, respectively), which was significantly higher (p Soxhlet extraction. Meanwhile, tea seed oil extracted by SC-CO2 contained approximately 80% unsaturated fatty acids and showed a much stronger scavenging ability on the DPPH radical than that extracted by Soxhlet. SC-CO2 is a promising alternative for efficient extraction of edible oil from tea seed. Moreover, tea seed oil extracted by SC-CO2 is highly edible and has good antioxidant activity, and therefore may play a potential role as a health-promoting food resource in human diets. PMID:22174626

  3. Fatty acid composition and antioxidant activity of tea (Camellia sinensis L.) seed oil extracted by optimized supercritical carbon dioxide.

    Science.gov (United States)

    Wang, Yuefei; Sun, Da; Chen, Hao; Qian, Lisheng; Xu, Ping

    2011-01-01

    Seeds are another product in addition to leaves (raw materials for teas) of tea (Camellia sinensis L.) plant. The great increase of tea consumption in recent years raises the challenge of finding commercial applications for tea seeds. In the present study, supercritical carbon dioxide (SC-CO(2)) extraction edible oil from tea seed was carried out, response surface methodology (RSM) was used to optimize processing parameters including time (20-90 min), temperature (35-45 °C) and pressure (50-90 MPa). The fatty acid composition and antioxidant activity of the extracted oil was also investigated. The highest yield of oil (29.2 ± 0.6%) was obtained under optimal SC-CO(2) extraction conditions (45 °C, 89.7 min and 32 MPa, respectively), which was significantly higher (p < 0.05) than that (25.3 ± 1.0%) given by Soxhlet extraction. Meanwhile, tea seed oil extracted by SC-CO(2) contained approximately 80% unsaturated fatty acids and showed a much stronger scavenging ability on the DPPH radical than that extracted by Soxhlet. SC-CO(2) is a promising alternative for efficient extraction of edible oil from tea seed. Moreover, tea seed oil extracted by SC-CO(2) is highly edible and has good antioxidant activity, and therefore may play a potential role as a health-promoting food resource in human diets.

  4. Fatty Acid Composition and Antioxidant Activity of Tea (Camellia sinensis L. Seed Oil Extracted by Optimized Supercritical Carbon Dioxide

    Directory of Open Access Journals (Sweden)

    Ping Xu

    2011-11-01

    Full Text Available Seeds are another product in addition to leaves (raw materials for teas of tea (Camellia sinensis L. plant. The great increase of tea consumption in recent years raises the challenge of finding commercial applications for tea seeds. In the present study, supercritical carbon dioxide (SC-CO2 extraction edible oil from tea seed was carried out, response surface methodology (RSM was used to optimize processing parameters including time (20–90 min, temperature (35–45 °C and pressure (50–90 MPa. The fatty acid composition and antioxidant activity of the extracted oil was also investigated. The highest yield of oil (29.2 ± 0.6% was obtained under optimal SC-CO2 extraction conditions (45 °C, 89.7 min and 32 MPa, respectively, which was significantly higher (p < 0.05 than that (25.3 ± 1.0% given by Soxhlet extraction. Meanwhile, tea seed oil extracted by SC-CO2 contained approximately 80% unsaturated fatty acids and showed a much stronger scavenging ability on the DPPH radical than that extracted by Soxhlet. SC-CO2 is a promising alternative for efficient extraction of edible oil from tea seed. Moreover, tea seed oil extracted by SC-CO2 is highly edible and has good antioxidant activity, and therefore may play a potential role as a health-promoting food resource in human diets.

  5. Wheat germ oil extracted by supercritical carbon dioxide with ethanol: Fatty acid composition

    International Nuclear Information System (INIS)

    Parczewska-Plesnar, B.; Brzozowski, R.; Gwardiak, H.; Białecka-Florjańczyk, E.; Bujnowski, Z.

    2016-01-01

    In this work, supercritical fluid extraction (SFE) using CO2 with ethanol as entrainer was performed at a temperature of 40 o C under a pressure of 21 MPa. For comparison, a similar extraction without the entrainer was carried out. The extraction yield of wheat germ using supercritical CO2 with ethanol was slightly higher (10.7 wt%) than that of extraction without the entrainer (9.9 wt%). Fractions of SFE extracts were collected separately during the experiments and the composition of fatty acids in each fraction was analyzed. The SFE extracted oils were rich (63.4-71.3%) in the most valuable polyunsaturated fatty acids (PUFA) and their content in all collected fractions was approximately constant. Similar PUFA contents were found in the reference samples of oils extracted by n-hexane (66.2-67.0%), while the commercial cold-pressed oil contained significantly less PUFA (60.2%). These results show a higher nutritional value of the oil obtained by extraction with supercritical CO2 than cold pressed oil which is generally considered to be very valuable. [es

  6. Evaluation of the essential oil of Foeniculum vulgare Mill (fennel) fruits extracted by three different extraction methods by GC/MS.

    Science.gov (United States)

    Hammouda, Faiza M; Saleh, Mahmoud A; Abdel-Azim, Nahla S; Shams, Khaled A; Ismail, Shams I; Shahat, Abdelaaty A; Saleh, Ibrahim A

    2014-01-01

    Hydrodistillation (HD) and steam-distillation, or solvent extraction methods of essential oils have some disadvantages like thermal decomposition of extracts, its contamination with solvent or solvent residues and the pollution of residual vegetal material with solvent which can be also an environmental problem. Thus, new green techniques, such as supercritical fluid extraction and microwave assisted techniques, are potential solutions to overcome these disadvantages. The aim of this study was to evaluate the essential oil of Foeniculum vulgare subsp. Piperitum fruits extracted by three different extraction methods viz. Supercritical fluid extraction (SFE) using CO2, microwave-assisted extraction (MAE) and hydro-distillation (HD) using gas chromatography-mass spectrometry (GC/MS). The results revealed that both MAE and SFE enhanced the extraction efficiency of the interested components. MAE gave the highest yield of oil as well as higher percentage of Fenchone (28%), whereas SFE gave the highest percentage of anethol (72%). Microwave-assisted extraction (MAE) and supercritical fluid extraction (SFE) not only enhanced the essential oil extraction but also saved time, reduced the solvents use and produced, ecologically, green technologies.

  7. Solvent extraction of base oil from used lubricant oil: a study on the performance of zeolite adsorption

    International Nuclear Information System (INIS)

    Lim Lee Ping; Rosli Mohd Yunus; Adnan Ripin

    2001-01-01

    Solvent extraction is known as one of the potential techniques for recycling used lubricant oil. The recovered oil is identical to the virgin oil, but the oil maintains its darkish color and some odor. This paper is to study the performance of zeolite in removing color and odor. A part from the study, factorial design analysis indicated that the concentration of zeolite exerts to be the most influenced on the adsorption process in which the increase of zeolite concentration resulted in an average increase of 2.22% adsorption response. The number of contact stage appeared to be the second most influential effects, which brought an average increase of 1.38% adsorption response. Further more, it was found that the interaction between the concentration of zeolite and the number of contact stage was the most significant of all interactions under study, at 2.71%. Thus, the additions of 10 g zeolite in 50 ml base oil of 3 rd stage color removal produces the best color removal from the recovered base oil. (Author)

  8. Resinous constituent extracting process

    Energy Technology Data Exchange (ETDEWEB)

    Sayer, W F

    1947-10-07

    The method of recovering oily constituents from coal or oil shale comprising the saturation of coal or oil shale in a sealed vessel with an organic solution having a boiling point at atmospheric pressure of not exceeding 220/sup 0/C, elevating the temperature within the vessel to a temperature below the cracking temperature of the constituents and maintaining the pressure within the vessel below 51 pounds, to extract the oily material from the coal or oil shale and subsequently separating the solvent from the oily material.

  9. Chemical composition and oxidative stability of jussara (Euterpe edulis M.) oil extracted by cold and hot mechanical pressing

    International Nuclear Information System (INIS)

    Da Cunha, A.L.A.; Freitas, S.P.; Godoy, R.L.O.; Cabral, L.M.C.; Tonon, R.V.

    2017-01-01

    The aim of this work was to evaluate the effect of mechanical pressing on jussara oil yield, oxidative stability and carotenoid profile with or without heat application. Firstly, jussara pulp was centrifuged for juice extraction, and the resulting cake was dried until reaching 10% moisture content. Then, oil extraction was performed in an expeller press at 25 ºC (cold pressing) and at 50 ºC (hot pressing). The process performance was evaluated by the oil yield, and the crude jussara oil was characterized for fatty acid composition, acid value, carotenoid profile and oxidative stability. Jussara oil contained 74% unsaturated fatty acids, mainly oleic and linoleic acids (48% and 24%, respectively). The oil yield was almost twice as high for the hot process as compared to the cold one. Additionally, hot pressing resulted in 25% higher total carotenoid content as compared to cold pressing, with β-carotene as the most abundant one. Hot and cold pressing showed no difference in oil oxidative stability and fatty acid composition. [es

  10. Essential oils: extraction, bioactivities, and their uses for food preservation.

    Science.gov (United States)

    Tongnuanchan, Phakawat; Benjakul, Soottawat

    2014-07-01

    Essential oils are concentrated liquids of complex mixtures of volatile compounds and can be extracted from several plant organs. Essential oils are a good source of several bioactive compounds, which possess antioxidative and antimicrobial properties. In addition, some essential oils have been used as medicine. Furthermore, the uses of essential oils have received increasing attention as the natural additives for the shelf-life extension of food products, due to the risk in using synthetic preservatives. Essential oils can be incorporated into packaging, in which they can provide multifunctions termed "active or smart packaging." Those essential oils are able to modify the matrix of packaging materials, thereby rendering the improved properties. This review covers up-to-date literatures on essential oils including sources, chemical composition, extraction methods, bioactivities, and their applications, particularly with the emphasis on preservation and the shelf-life extension of food products. © 2014 Institute of Food Technologists®

  11. Application of GC–MS chromatography for the analysis of the oil fractions extracted by supercritical CO2 at high pressure

    DEFF Research Database (Denmark)

    Rudyk, Svetlana Nikolayevna; Spirov, Pavel; Søgaard, Erik Gydesen

    2013-01-01

    GC–MS chromatographic analysis has been applied for the investigation of the fractions of oil extracted by supercritical carbon dioxide at a temperature of 60 °C and at pressure values ranging from 22 to 56 MPa. The observations revealed, that the whole extraction process is clearly reflected...... in the chromatograms, demonstrating how the heavier hydrocarbon fractions were gradually involved in the extraction process. The shape of the chromatograms alters with increasing pressure from triangle to trapezoid, approaching the shape of the chromatogram of the crude oil. The observation of the fingerprints...

  12. Radionuclide concentrations in oil extraction and production processes in Northeast Brazil; Teores de radionuclideos em processos de extracao e de producao de petroleo no nordeste do Brasil

    Energy Technology Data Exchange (ETDEWEB)

    Gazineu, Maria Helena Paranhos

    2005-06-15

    Since the beginning of the twentieth century the presence of naturally occurring radioactive material (NORM) was detected in the water and oil extracted from wells both onshore and offshore. The oil is extracted together with water and sediments which contain radionuclides of the uranium and thorium series. Among the radionuclides present, especial attention should be given to {sup 226}Ra and {sup 228}Ra, due to its long half-life and importance, from the radiological point of view. The objective of this work was to identify the natural radionuclides in the oil industry, to determine their activity concentration, and from these results, to evaluate the risks the employees of the oil industry are exposed to. Samples of sludge, scale and produced water extracted with the oil were collected from three oil processing stations in the state of Sergipe, Brazil. The activity concentrations of the radionuclides were determined in the solid samples before and after the extraction of the oil. The chemical and mineralogical composition of the samples without oil was evaluated. Water samples, on the other hand, were analyzed for their contents of radionuclides and barium concentration. It was observed that the activity concentrations of the analyzed radionuclides ({sup 226}Ra, {sup 228}Ra, {sup 228}Th and {sup 210}Pb) in sludge and scales were very high when compared with the literature, particularly much higher than the values for {sup 226}Ra and {sup 228}Ra obtained for sludge and scales from the oil platforms near the city of Campos, state of Rio de Janeiro. The maximum concentration values for {sup 226}Ra, {sup 228}Ra, {sup 228}Th and {sup 210}Pb (3,500, 2,195, 2,248.6 and 201 kBq kg{sup -1}, respectively) were obtained for the scales after the extraction of the oil. The analysis of the samples showed that barium sulphate (barite) and strontium sulphate (celestite) are the main constituents of the scales, while carbonates and silicates, together with other compounds are the

  13. Terpenes as Green Solvents for Extraction of Oil from Microalgae

    Directory of Open Access Journals (Sweden)

    Celine Dejoye Tanzi

    2012-07-01

    Full Text Available Herein is described a green and original alternative procedure for the extraction of oil from microalgae. Extractions were carried out using terpenes obtained from renewable feedstocks as alternative solvents instead of hazardous petroleum solvents such as n-hexane. The described method is achieved in two steps using Soxhlet extraction followed by the elimination of the solvent from the medium using Clevenger distillation in the second step. Oils extracted from microalgae were compared in terms of qualitative and quantitative determination. No significant difference was obtained between each extract, allowing us to conclude that the proposed method is green, clean and efficient.

  14. Disinfection of vegetable seed by treatment with essential oils, organic acids and plant extract

    NARCIS (Netherlands)

    Wolf, van der J.M.; Birnbaum, Y.E.; Zouwen, van der P.S.; Groot, S.P.C.

    2008-01-01

    Various essential oils, organic acids, Biosept, (grapefruit extract), Tillecur and extracts of stinging nettle and golden rod were tested for their antimicrobial properties in order to disinfect vegetable seed. In in vitro assays, thyme oil, oregano oil, cinnamon oil, clove oil and Biosept had the

  15. Pollutant in palm oil production process.

    Science.gov (United States)

    Hosseini, Seyed Ehsan; Abdul Wahid, Mazlan

    2015-07-01

    Palm oil mill effluent (POME) is a by-product of the palm industry and it releases large amounts of greenhouse gases (GHGs). Water systems are also contaminated by POME if it is released into nonstandard ponds or rivers where it endangers the lives of fish and water fowl. In this paper, the environmental bottlenecks faced by palm oil production were investigated by analyzing the data collected from wet extraction palm oil mills (POMs) located in Malaysia. Strategies for reducing pollution and technologies for GHG reduction from the wet extraction POMs were also proposed. Average GHG emissions produced from processing 1 ton of crude palm oil (CPO) was 1100 kg CO2eq. This amount can be reduced to 200 kg CO2eq by capturing biogases. The amount of GHG emissions from open ponds could be decreased from 225 to 25 kg CO2eq/MT CPO by covering the ponds. Installation of biogas capturing system can decrease the average of chemical oxygen demand (COD) to about 17,100 mg/L and stabilizing ponds in the final step could decrease COD to 5220 mg/L. Using a biogas capturing system allows for the reduction of COD by 80% and simultaneously using a biogas capturing system and by stabilizing ponds can mitigate COD by 96%. Other ways to reduce the pollution caused by POME, including the installation of wet scrubber vessels and increasing the performance of biogas recovery and biogas upgrading systems, are studied in this paper. Around 0.87 m3 POME is produced per 1 ton palm fruit milled. POME consists of around 2% oil, 2-4% suspended solid, 94-96% water. In palm oil mills, more than 90% of GHGs were emitted from POME. From 1 ton crude palm oil, 1100 kg CO2eq GHGs are generated, which can be reduced to 200 kg CO2eq by installation of biogas capturing equipment.

  16. In growing pigs, the true ileal and total tract digestibility of acid hydrolyzed ether extract in extracted corn oil is greater than in intact sources of corn oil or soybean oil.

    Science.gov (United States)

    Kim, B G; Kil, D Y; Stein, H H

    2013-02-01

    An experiment was conducted to determine the true ileal digestibility (TID) and the true total tract digestibility (TTTD) of acid-hydrolyzed ether extract (AEE) in extracted corn oil, high-oil corn, distillers dried grains with solubles (DDGS), corn germ, and high protein distillers dried grains (HP DDG) and to compare these values to the TID and TTTD of AEE in full-fat soybeans. Nineteen barrows with an initial BW of 52.2 kg (SD = 3.8) were fitted with a T-cannula in the distal ileum and allotted to a 19 × 11 Youden square design with 19 diets and 11 periods. A basal diet based on cornstarch, casein, sucrose, and corn bran was formulated. Eighteen additional diets were formulated by adding 3 levels of extracted corn oil, high-oil corn, DDGS, corn germ, HP DDG, or full-fat soybeans to the basal diet. The apparent ileal and the apparent total tract digestibility of AEE were calculated for each diet. The endogenous flow of AEE associated with each ingredient and values for TID and TTTD were calculated using the regression procedure. Results indicated that digested AEE in ileal digesta and feces linearly increased as AEE intake increased regardless of ingredient (P 0.77). However, the ileal and fecal endogenous losses of AEE were different (P oil, HP DDG, and full-fat soybeans. The TID of AEE was greater (P oil (95.4%) than for all other ingredients. The TID of AEE in HP DDG (76.5%) was not different from the TID of AEE in full-fat soybeans (85.2%) but greater (P oil corn, DDGS, and corn germ (53.0, 62.1, and 50.1%, respectively). The TTTD of AEE was greater (P oil (94.3%) than for all other ingredients, and the TTTD in full-fat soybeans (79.7%) was greater (P oil corn, DDGS, corn germ, and HP DDG (41.4, 51.9, 43.9, and 70.2%, respectively). The TTTD of AEE in HP DDG was also greater (P oil corn, DDGS, and corn germ. In conclusion, the intact sources of oil originating from high-oil corn, DDGS, corn germ, or HP DDG are much less digestible than extracted corn oil

  17. Antioxidant Activity of Essential Oil and Extracts of Valeriana jatamansi Roots

    Directory of Open Access Journals (Sweden)

    Sakshima Thusoo

    2014-01-01

    Full Text Available Valeriana jatamansi is an indigenous medicinal plant used in the treatment of a number of diseases. In the present study, chemical composition of the essential oil was determined by GC-MS. Seven major components were identified in Valeriana jatamansi essential oil, namely, β-vatirenene, β-patchoulene, dehydroaromadendrene, β-gurjunene, patchoulic alcohol, β-guaiene, and α-muurolene. Methanolic, aqueous, and chloroform extracts of Valeriana jatamansi roots were also prepared and analyzed for their polyphenols and flavonoid content. Antioxidant activity of essential oil and different extracts of Valeriana jatamansi roots was determined by DPPH radical scavenging and chelation power assay. A linear correlation has been obtained by comparing the antioxidant activity and polyphenols and flavonoid content of the extracts. Results indicated that antioxidant activity of methanolic extract could be attributed to the presence of rich amount of polyphenols and flavonoid. Essential oil of Valeriana jatamansi roots showed moderate antioxidant activity.

  18. Bio-oil extraction of Jatropha curcas with ionic liquid co-solvent: Fate of biomass protein.

    Science.gov (United States)

    Severa, Godwin; Edwards, Melisa; Cooney, Michael J

    2017-02-01

    The fate of oil-seed biomass protein has been tracked through all steps of a multi-phase extraction process using an ionic liquid based co-solvent system previously demonstrated to extract bio-oil and phorbol esters and to recover fermentable sugars from Jatropha oil seed. These analyses, however, did not address the fate of biomass protein. This work demonstrated that the majority of protein (∼86%) tracked with the biomass with the balance lost to co-solvent (∼12%) and methanol (∼2%) washes. A significant portion of the ionic liquid remained with the treated biomass and required aggressive methanol washes to recover. A system analysis showed a net-positive energy balance and thus the potential of this system to produce both bio-oil and protein-rich toxin-free biomass. While these results further support Jatropha as an oil seed crop, the additional costs of solvent recovery will need to be addressed if commercialization is to be realized. Copyright © 2016 Elsevier Ltd. All rights reserved.

  19. Extraction of sunflower oil by twin screw extruder: screw configuration and operating condition effects

    Energy Technology Data Exchange (ETDEWEB)

    Kartika, I.A. [FATETA-IPB, Bogor (Indonesia). Department of Agroindustrial Technology; Pontalier, P.Y.; Rigal, L. [Laboratoire de Chimie Agro-Industrielle, UMR 1010 INRA/INP-ENSIACET, Toulouse (France)

    2006-12-15

    The objective of this study was to investigate the screw configuration allowing oil extraction from sunflower seeds with a twin-screw extruder. Experiments were conducted using a co-rotating twin-screw extruder. Five screw profiles were examined to define the best performance (oil extraction yield, specific mechanical energy and oil quality) by studying the influence of operating conditions, barrel temperature, screw speed and feed rate. Generally, the position and spacing between two reversed screw elements affected oil extraction yield. An increase of oil extraction yield was observed as the reversed screw elements were moved with increased spacing between two elements and with smaller pitch elements. In addition, oil extraction yield increased as barrel temperature, screw speed and feed rate were decreased. Highest oil extraction yield (85%) with best cake meal quality (residual oil content lower than 13%) was obtained under operating conditions of 120 {sup o}C, 75 rpm and 19 kg/h. Furthermore, the operating parameters influenced energy input. A decrease in barrel temperature and feed rate followed by an increase in screw speed increased energy input, particularly specific mechanical energy input. Effect of the operating parameters on oil quality was less important. In all experiments tested, the oil quality was very good. The acid value was below 2 mg of KOH/g of oil and total phosphorus content was low, below 100 mg/kg. (author)

  20. Study of volatile oil component of petal and herbal and extraction of seed oil in Borage by Cold Press method

    Directory of Open Access Journals (Sweden)

    esfandiar Hassani Moghadam

    2010-03-01

    Full Text Available There is a few reported about the volatile oil component of petal, herbal and component of seed oil of borage. This research worked carried out for analysis and identification the volatile oil in herbals, petals, and seed oil compositions of Borago officinalis L. in Lorestan province. Material and methods: Extraction of essential oil from petals carried out using steam distillation by Clevenger apparatus. The new SPME-GC/MS method is used for extraction and identification of volatile oil compounds in the herbal of borage. The oil of the seeds was extracted using a Cold-press method. The identification of chemical composition of extracted oil was carried out by GC/MS apparatus. Results: In petals of Borage only Carvacerol component, and in the herbal of Borage three components Carvacrol, Bisabolone oxide and 2-Phenylethyl benzoate, extracted and identified respectively. In the seed oil of borage 16 different components were separated and identified. The following components had the highest amount in seed oil: Hexadecane, N, N-dimethylethanolamine, Beta-d-glycoside, 3, 6-glucurono-methyl, Benzaldehde, 4-methyl 3-Hydroxytetrahydrofuran, Hexadecanoic acid, Heptanoic acid, Gamma butyrolactone and Ethyl octadec-9-enoate are the major components respectively. These components contain 63.4% of all components in borage seed oil and the 7 residual components only 9.5% all of the components in borage seed oil. Also one unknown (27.1% component identified. Conclusion: Using result obtained from this research the volatile oil a few amounts of the borage chemical composition. The results show that the seed oil of this species can be used for medicinal preparation. Cold Press method was found to be rapid and simple for identification of seeds oil components.

  1. Optimization of oil yield from Hevea brasiliensis seeds through ultrasonic-assisted solvent extraction via response surface methodology

    Directory of Open Access Journals (Sweden)

    Val Irvin F. Mabayo

    2018-01-01

    Full Text Available The demand for oil has been increasing vastly over time, and the source of this has slowly been diminishing. The use of non-food feedstock is seen as a promising alternative source for the production of bio-based fuel. In this study, rubber (Hevea brasiliensis seeds were utilized as biomass in bio-oil production considering that these are non-edible and considered wastes in rubber tree plantations. In the oil extraction process, the rubber seed kernels were oven dried at 100 °C for 24 h, powdered and then dried further at 105 °C for 4 h. After characterization, optimization study was done using Design Expert 7.0 software through central composite design of the response surface methodology. Ultrasonication technology was employed in the oil extraction process which significantly reduced the reaction time needed for extraction to 15 min compared the conventional extraction method of at least 8 h. An optimum rubber seed oil (RSO yield of 30.3 ± 0.3% was obtained using 15 g biomass, 5:1 n-hexane to biomass (mL g−1 ratio, 50 μm resonance amplitude and 60 ± 5 °C temperature at 15 min reaction time. The oil yield at optimum condition was found to have 0.89 g mL−1 density at room temperature, 26.7 cSt kinematic viscosity at 40 °C and high heating value of 39.2 MJ kg−1. The Fourier Transform Infrared Radiation spectroscopy analysis of the RSO, at optimum condition, showed the presence of carboxylic acid and ester carbonyl functional groups which are good indicators as a potential source of biodiesel. Keywords: Hevea brasiliensis, Oil extraction, Optimization, Response surface methodology, Rubber seed oil, Ultrasonic-assisted solvent extraction

  2. Mixing in three-phase systems: Implications for enhanced oil recovery and unconventional gas extraction

    Science.gov (United States)

    Jimenez-Martinez, J.; Porter, M. L.; Hyman, J.; Carey, J. W.; Viswanathan, H. S.

    2015-12-01

    Although the mixing of fluids within a porous media is a common process in natural and industrial systems, how the degree of mixing depends on the miscibility of multiple phases is poorly characterized. Often, the direct consequence of miscible mixing is the modification of the resident fluid (brine and hydrocarbons) rheological properties. We investigate supercritical (sc)CO2 displacement and mixing processes in a three-phase system (scCO2, oil, and H2O) using a microfluidics experimental system that accommodates the high pressures and temperatures encountered in fossil fuel extraction operations. The miscibility of scCO2 with the resident fluids, low with aqueous solutions and high with hydrocarbons, impacts the mixing processes that control sweep efficiency in enhanced oil recovery (EOR) and the unlocking of the system in unconventional oil and gas extraction. Using standard volume-averaging techniques we upscale the aqueous phase saturation to the field-scale (i.e., Darcy scale) and interpret the results as a simpler two-phase system. This process allows us to perform a statistical analysis to quantify i) the degree of heterogeneity in the system resulting from the immiscible H2O and ii) how that heterogeneity impacts mixing between scCO2 and oil and their displacement. Our results show that when scCO2 is used for miscible displacement, the presence of an aqueous solution, which is common in secondary and tertiary EOR and unconventional oil and gas extraction, strongly impacts the mixing of scCO2 with the hydrocarbons due to low scCO2-H2O miscibility. H2O, which must be displaced advectively by the injected scCO2, introduces spatio-temporal variability into the system that acts as a barrier between the two miscibile fluids. This coupled with the effect of viscosity contrast, i.e., viscous fingering, has an impact on the mixing of the more miscible pair.

  3. Waste to Want: Polymer nanocomposites using nanoclays extracted from Oil based drilling mud waste

    International Nuclear Information System (INIS)

    Adegbotolu, Urenna V; Njuguna, James; Pollard, Pat; Yates, Kyari

    2014-01-01

    Due to the European Union (EU) waste frame work directive (WFD), legislations have been endorsed in EU member states such as UK for the Recycling of wastes with a vision to prevent and reduce landfilling of waste. Spent oil based drilling mud (drilling fluid) is a waste from the Oil and Gas industry with great potentials for recycling after appropriate clean-up and treatment processes. This research is the novel application of nanoclays extracted from spent oil based drilling mud (drilling fluid) clean-up as nanofiller in the manufacture of nanocomposite materials. Research and initial experiments have been undertaken which investigate the suitability of Polyamide 6 (PA6) as potential polymer of interest. SEM and EDAX were used to ascertain morphological and elemental characteristics of the nanofiller. ICPOES has been used to ascertain the metal concentration of the untreated nanofiller to be treated (by oil and heavy metal extraction) before the production of nanocomposite materials. The challenges faced and future works are also discussed

  4. Kinetics and thermodynamics of cottonseed oil extraction

    Directory of Open Access Journals (Sweden)

    Saxena, Devesh K.

    2011-06-01

    Full Text Available Petroleum derived n-hexane is commercially used in solvent extraction plants due to its higher extraction efficiency in spite of the fact that it is graded as highly toxic and hazardous. The present study is based on the use of both a much safer and non toxic solvent ethanol and n-hexane for the extraction of oil from cottonseed. The extraction data were obtained by varying temperature, solvent-solid ratio and particle size, to compare the extraction efficiency of both ethanol and n-hexane. The data show that nearly the same amount of extraction is possible at a higher solvent-solid ratio for both the solvents. This study has established that the kinetics of oil extraction follows a second order reaction mechanism. The thermodynamic analysis of the data shows that both ΔHº and ΔSº are positive, and ΔGº is negative indicating that the extraction process is endothermic, irreversible, and spontaneous.

    El n-hexano derivado del petróleo es comercialmente usado en plantas de extracción con disolventes debido a su mayor eficiencia de extracción, a pesar de que está calificado como altamente tóxico y peligroso. El presente estudio está basado en el uso de etanol, disolvente mucho más seguros y no tóxico, y n-hexano en la extracción de aceite de algodón. Los datos de extracción fueron obtenidos variando la temperatura, la proporción sólido-disolvente y el tamaño de partícula, para comparar la eficiencia de extracción del etanol y del hexano. Los datos muestran que casi la misma cantidad de extracción es posible para ambos disolventes a la proporción más alta de sólido-disolvente. Este estudio es capaz de establecer que las cinéticas de extracción de aceite siguen un mecanismo de reacción de segundo orden. El análisis termodinámico de los datos mostró que ΔHº and ΔSº son positivas, y ΔGº es negativa, indicando que el proceso de extracción es endotérmico, irreversible y espontáneo.

  5. In-vitro antibacterial activity of essential oils extracted from locally available medicinal plants

    International Nuclear Information System (INIS)

    Ara, G.; Shawar, D.; Akbar, A.; Kanwal, F.; Imran, M.

    2011-01-01

    Extraction of essential oils from locally available species of four plants, Nigella sativa, Syzygium aromaticum, Cinnamomum tenuis and Curcuma aromatica was carried out using steam distillation followed by ether extraction. Dried and purified extracted oils were screened for their antibacterial activity against three bacterial strains namely, Bacillus lichaniformis (Gram +ve), Micrococcus leutus (Gram +ve) and Salmonella Typhimurium (Gram -ve) using Mc. Cartney's method. Minimum Inhibition Concentration (MIC) values of these oils were also determined. It was observed that the oils extracted from Nigella sativa and Cinnamomum tenuis were found to be more potent as compared to other two species. With the exception of Nigella sativa, all the other oils showed bacterial inhibition at 50 mmol concentration. These results support that these plant oils can be used to cure bacterial infections and may also have role as pharmaceuticals and preservatives. (author)

  6. Seed oil extraction from red prickly pear using hexane and supercritical CO2 : assessment of phenolic compound composition, antioxidant and antibacterial activities.

    Science.gov (United States)

    Koubaa, Mohamed; Mhemdi, Houcine; Barba, Francisco J; Angelotti, Armel; Bouaziz, Fatma; Chaabouni, Semia Ellouz; Vorobiev, Eugène

    2017-01-01

    Investigating Opuntia species for their seed oil content is of much importance owing to their potential use for food and in cosmetic applications. These oils have an important content in unsaturated fatty acids as well as antioxidant compounds (e.g. polyphenols, vitamin E), which have been associated with the prevention of some chronic diseases. Moreover, Opuntia stricta oils possess important antimicrobial activities. For instance, the main focus of this study was to compare the effectiveness of conventional (hexane extraction) and novel (supercritical (SC)-CO 2 ) extraction methods for the recovery of oil and phenolic compounds from O. stricta seeds. The oil yield of both extracts was then compared and the polyphenol content and composition of both extracts were determined by liquid chromatography-high-resolution mass spectrometry. Additionally, antioxidant (DPPH assay) and antimicrobial activities (disc diffusion method) of O. stricta seed oils were determined. The oil yield (based on Soxhlet's method) of O. stricta seeds was determined using SC-CO 2 (49.9 ± 2.2%), and hexane (49.0 ± 1.5%). Although obtaining similar oil extraction yields using the two methods, the extracted oil using SC-CO 2 was more enriched in polyphenols (172.2 ± 11.9 µg gallic acid equivalents (GAE) g -1 oil) than that extracted using hexane (76.0 ± 6.9 µg GAE g -1 of oil). Polyphenol profiles showed that the SC-CO 2 process led to the yield of more compounds (45) than that using hexane extraction (11). Moreover, the antioxidant and antimicrobial activities of SC-CO 2 extract showed a high percentage of inhibition. SC-CO 2 extraction of O. stricta seed oil led to extraction of oil with a similar yield to that with hexane extraction, but with higher polyphenol content. The extract containing polyphenols exhibited high antioxidant and antibacterial properties, demonstrating their great potential as feedstock for high-oil quality. © 2016 Society of Chemical Industry. © 2016 Society of

  7. A study of extraction of oil through a polymer flooding method

    Energy Technology Data Exchange (ETDEWEB)

    Aliyev, V.S.; Agazade, A.D.; Asadov, Z.G.; Yusubov, A.Yu.

    1983-01-01

    A number of representatives of water soluble acrylic polymers is synthesized. These include polyacrylamine (PAA), methylated polyacrylamine, polymethacrylic acid (PMAK) and its alkaline salts. The oil extracting properties of the synthesized polymers are studied in a laboratory installation. The effectiveness for extracting Romaninsk oil of solutions of polyacrylamine, methylated polyacrylamine and polymethacrylic acid in alkaline stratum water (the effect is 12 to 17 percent) is shown. It is established that the solutions of alkaline (sodium, potassium, and ammonium) salts of polymethacrylic acid in fresh water have good extracting capabilities as compared to light Balakhansk oil. The effect is 14 to 19 percent.

  8. Evaluation of energy efficiency efforts of oil and gas offshore processing

    DEFF Research Database (Denmark)

    Nguyen, Tuong-Van; Voldsund, Mari; Breuhaus, Peter

    2015-01-01

    the energy performance of these facilities, by decreasing the power and heating requirements and designing more efficient processes. Several technologies that have been proposed are to (i) promote energy integration within the oil and gas processing plant, (ii) add an additional pressure extraction level......, (iii) implement multiphase expanders, and (iv) install a waste heat recovery system. The present work builds on two case studies located in the North and Norwegian Seas, which differ by the type of oil processed, operating conditions and strategies. The findings suggest that no generic improvement can...

  9. SOLVENT-BASED ENHANCED OIL RECOVERY PROCESSES TO DEVELOP WEST SAK ALASKA NORTH SLOPE HEAVY OIL RESOURCES

    Energy Technology Data Exchange (ETDEWEB)

    David O. Ogbe; Tao Zhu

    2004-01-01

    A one-year research program is conducted to evaluate the feasibility of applying solvent-based enhanced oil recovery processes to develop West Sak and Ugnu heavy oil resources found on the Alaska North Slope (ANS). The project objective is to conduct research to develop technology to produce and market the 300-3000 cp oil in the West Sak and Ugnu sands. During the first phase of the research, background information was collected, and experimental and numerical studies of vapor extraction process (VAPEX) in West Sak and Ugnu are conducted. The experimental study is designed to foster understanding of the processes governing vapor chamber formation and growth, and to optimize oil recovery. A specially designed core-holder and a computed tomography (CT) scanner was used to measure the in-situ distribution of phases. Numerical simulation study of VAPEX was initiated during the first year. The numerical work completed during this period includes setting up a numerical model and using the analog data to simulate lab experiments of the VAPEX process. The goal was to understand the mechanisms governing the VAPEX process. Additional work is recommended to expand the VAPEX numerical study using actual field data obtained from Alaska North Slope.

  10. Compositional and functional difference in cumin (Cuminum cyminum essential oil extracted by hydrodistillation and SCFE

    Directory of Open Access Journals (Sweden)

    Supradip Saha

    2016-12-01

    Full Text Available Essential oils were obtained from same raw material of cumin seed by extraction with hydrodistillation and super critical fluid extraction (SCFE. For SCFE, supercritical carbon dioxide at 45°C and 100 bar was used as variable for the extraction. The composition of the extracts was determined by gas chromatography-mass spectrometry. Yield of essential oil was more in the SCFE method. Extract obtained by supercritical fluid extraction technique using CO2 was heavier than the hydrodistilled volatile oil. Cumin oil obtained by hydrodistillation contained higher percentage of cuminaldehyde (52.6%, then did oil obtained by SCFE (37.3%, whereas cumin oil obtained by hydrodistillation had the lower percentage of cuminic alcohol (13.3% as compared to 19.3% in SCFE method. However, cuminal (2-caren-10-al content was almost similar in cumin oil obtained by the SCFE and hydrodistillation method (24.5–25.8%. Hydrodistilled volatile oil showed better antioxidant activity measured by DPPH and FRAP assay and more total phenol content. The results indicated that though essential oil yield was more in the SCFE method, antioxidant property was more in conventional hydrodistillation method. SCFE extracted non polar (wax materials compounds along with volatile oil and it was recorded that enhanced aroma of signature compounds of cumin.

  11. Characterization of Linum usitatissimum L. oil obtained from different extraction technique and in vitro antioxidant potential of supercritical fluid extract

    Science.gov (United States)

    Chauhan, Rishika; Chester, Karishma; Khan, Yasmeen; Tamboli, Ennus Tajuddin; Ahmad, Sayeed

    2015-01-01

    Aim: Present investigation was aimed to characterize the fixed oil of Linum usitatissimum L. using five different extraction methods: Supercritical fluid extraction (SFE), ultrasound-assistance, soxhlet extraction, solvent extraction, and three phase partitioning method. Materials and Methods: The SFE conditions (temperature, pressure, and volume of CO2) were optimized prior for better yield. The extracted oils were analyzed and compared for their physiochemical parameters, high performance thin layer chromatography (HPTLC), gas chromatography-mass spectrometry (GC-MS), and Fourier-transformed infrared spectroscopy (FT-IR) fingerprinting. Antioxidant activity was also determined using 1,1-diphenyl-2-picrylhydrazyl and superoxide scavenging method. Result: The main fatty acids were α-linolenic acid, linoleic acid, palmitic acid, and stearic acid as obtained by GC-MS. HPTLC analysis revealed the presence of similar major components in chromatograms. Similarly, the pattern of peaks, as obtained in FT-IR and GC-MS spectra of same oils by different extraction methods, were superimposable. Conclusion: Analysis reported that the fixed oil of L. usitatissimum L. is a good source of n-3 fatty acid with the significant antioxidant activity of oil obtained from SFE extraction method. PMID:26681884

  12. Characterization of Linum usitatissimum L. oil obtained from different extraction technique and in vitro antioxidant potential of supercritical fluid extract

    Directory of Open Access Journals (Sweden)

    Rishika Chauhan

    2015-01-01

    Full Text Available Aim: Present investigation was aimed to characterize the fixed oil of Linum usitatissimum L. using five different extraction methods: Supercritical fluid extraction (SFE, ultrasound-assistance, soxhlet extraction, solvent extraction, and three phase partitioning method. Materials and Methods: The SFE conditions (temperature, pressure, and volume of CO2 were optimized prior for better yield. The extracted oils were analyzed and compared for their physiochemical parameters, high performance thin layer chromatography (HPTLC, gas chromatography-mass spectrometry (GC-MS, and Fourier-transformed infrared spectroscopy (FT-IR fingerprinting. Antioxidant activity was also determined using 1,1-diphenyl-2-picrylhydrazyl and superoxide scavenging method. Result: The main fatty acids were α-linolenic acid, linoleic acid, palmitic acid, and stearic acid as obtained by GC-MS. HPTLC analysis revealed the presence of similar major components in chromatograms. Similarly, the pattern of peaks, as obtained in FT-IR and GC-MS spectra of same oils by different extraction methods, were superimposable. Conclusion: Analysis reported that the fixed oil of L. usitatissimum L. is a good source of n-3 fatty acid with the significant antioxidant activity of oil obtained from SFE extraction method.

  13. Instant controlled pressure drop technology and ultrasound assisted extraction for sequential extraction of essential oil and antioxidants.

    Science.gov (United States)

    Allaf, Tamara; Tomao, Valérie; Ruiz, Karine; Chemat, Farid

    2013-01-01

    The instant controlled pressure drop (DIC) technology enabled both the extraction of essential oil and the expansion of the matrix itself which improved solvent extraction. The sequential use of DIC and Ultrasound Assisted Extraction (UAE) triggered complementary actions materialized by supplementary effects. We visualized these combination impacts by comparing them to standard techniques: Hydrodistillation (HD) and Solvent Extraction (SE). First, the extraction of orange peel Essential Oils (EO) was achieved by HD during 4h and DIC process (after optimization) during 2 min; EO yields was 1.97 mg/g dry material (dm) with HD compared to 16.57 mg/g d m with DIC. Second, the solid residue was recovered to extract antioxidant compounds (naringin and hesperidin) by SE and UAE. Scanning electron microscope showed that after HD the recovered solid shriveled as opposite to DIC treatment which expanded the product structure. HPLC analyses showed that the best kinetics and yields of naringin and hesperidin extraction was when DIC and UAE are combined. Indeed, after 1h of extraction, DIC treated orange peels with UAE were 0.825 ± 1.6 × 10(-2)g/g of dry material (dm) for hesperidin and 6.45 × 10(-2) ± 2.3 × 10(-4)g/g d m for naringin compared to 0.64 ± 2.7 × 10(-2)g/g of dry material (dm) and 5.7 × 10(-2) ± 1.6 × 10(-3)g/g d m, respectively with SE. By combining DIC to UAE, it was possible to enhance kinetics and yields of antioxidant extraction. Copyright © 2012 Elsevier B.V. All rights reserved.

  14. Study on effective utilization of palm oil (Part 2). Extraction of carotenes from palm oil

    Energy Technology Data Exchange (ETDEWEB)

    Mamuro, Hideo; Kubota, Yasuhiko; Shiina, Hisako; Nakasato, Satoshi

    1987-01-08

    This report is a part of the result of an international cooperation project with Malaysia Palm Oil Research Institute. Extraction of carotenes from palm oil was carried out by means of molecular distillation or adsorption method. High recovery and enrichment of carotene was obtained from the sample treated with phosphoric acid or polyphosphoric acid. However, even the maximum enrichment was only 3.8 times of carotene concentration of the sample, which was far remote from the target value of 10. The yield of recovery was also as low as 40%. Adsorption of carotenes was found to be chemisorptive in nature. The highest enrichment and recovery were obtained in the caseof oil pretreated with the phosphorous pentoxide, the recovery was 34.3% and enrichment was 11.3 which exceeded the target of 10. This adsorption process may be commercialized if the demand for carotene will grow to justify it. (2 figs, 7 tabs, 18 refs)

  15. Antioxidant and Antibacterial Activities of Crude Extracts and Essential Oils of Syzygium cumini Leaves

    Science.gov (United States)

    Mohamed, Amal A.; Ali, Sami I.; El-Baz, Farouk K.

    2013-01-01

    This research highlights the chemical composition, antioxidant and antibacterial activities of essential oils and various crude extracts (using methanol and methylene chloride) from Syzygium cumini leaves. Essential oils were analyzed by gas chromatography-mass spectrometry (GC-MS).The abundant constituents of the oils were: α-pinene (32.32%), β-pinene (12.44%), trans-caryophyllene (11.19%), 1, 3, 6-octatriene (8.41%), delta-3-carene (5.55%), α-caryophyllene (4.36%), and α-limonene (3.42%).The antioxidant activities of all extracts were examined using two complementary methods, namely diphenylpicrylhydrazyl (DPPH) and ferric reducing power (FRAP). In both methods, the methanol extract exhibited a higher activity than methylene chloride and essential oil extracts. A higher content of both total phenolics and flavonoids were found in the methanolic extract compared with other extracts. Furthermore, the methanol extract had higher antibacterial activity compared to methylene chloride and the essential oil extracts. Due to their antioxidant and antibacterial properties, the leaf extracts from S. cumini may be used as natural preservative ingredients in food and/or pharmaceutical industries. PMID:23593183

  16. Extractive oxidative desulfurization of model oil/crude oil using KSF montmorillonite-supported 12-tungstophosphoric acid

    Directory of Open Access Journals (Sweden)

    Ezzat Rafiee

    2016-10-01

    Full Text Available Abstract 12-Tungstophosphoric acid (PW supported on KSF montmorillonite, PW/KSF, was used as catalyst for deep oxidative desulfurization (ODS of mixed thiophenic compounds in model oil and crude oil under mild conditions using hydrogen peroxide (H2O2 as an oxidizing agent. A one-factor-at-a-time method was applied for optimizing the parameters such as temperature, reaction time, amount of catalyst, type of extractant and oxidant-to-sulfur compounds (S-compounds molar ratio. The corresponding products can be easily removed from the model oil by using ethanol as the best extractant. The results showed high catalytic activity of PW/KSF in the oxidative removal of dibenzothiophene (DBT and mixed thiophenic model oil under atmospheric pressure at 75 °C in a biphasic system. To investigate the oxidation and adsorption effects of crude oil composition on ODS, the effects of cyclohexene, 1,7-octadiene and o-xylene with different concentrations were studied.

  17. Extraction and the Fatty Acid Profile of Rosa acicularis Seed Oil.

    Science.gov (United States)

    Du, Huanan; Zhang, Xu; Zhang, Ruchun; Zhang, Lu; Yu, Dianyu; Jiang, Lianzhou

    2017-12-01

    Rosa acicularis seed oil was extracted from Rosa acicularis seeds by the ultrasonic-assisted aqueous enzymatic method using cellulase and protease. Based on a single experiment, Plackett-Burman design was applied to ultrasonic-assisted aqueous enzymatic extraction of wild rose seed oil. The effects of enzyme amount, hydrolysis temperature and initial pH on total extraction rate of wild rose seed oil was studied by using Box-Behnken optimize methodology. Chemical characteristics of a sample of Rosa acicularis seeds and Rosa acicularis seed oil were characterized in this work. The tocopherol content was 200.6±0.3 mg/100 g oil. The Rosa acicularis seed oil was rich in linoleic acid (56.5%) and oleic acid (34.2%). The saturated fatty acids included palmitic acid (4%) and stearic acid (2.9%). The major fatty acids in the sn-2 position of triacylglycerol in Rosa acicularis oil were linoleic acid (60.6%), oleic acid (33.6%) and linolenic acid (3.2%). According to the 1,3-random-2-random hypothesis, the dominant triacylglycerols were LLL (18%), LLnL (1%), LLP (2%), LOL (10%), LLSt (1.2%), PLP (0.2%), LLnP (0.1%), LLnO (0.6%) and LOP (1.1%). This work could be useful for developing applications for Rosa acicularis seed oil.

  18. Micro-pressing of rapeseed (Brassica napus L. and Arabidopsis thaliana seeds for evaluation of the oil extractability

    Directory of Open Access Journals (Sweden)

    Savoire Raphaëlle

    2010-03-01

    Full Text Available Pressing is a crucial step in the crushing process of rapeseed seeds, regarding its major effect on the oil extraction yield, the energy consumption and the quality of the meal. In order to study and model in a rigorous way the behaviour of rapeseed seeds, and the oil extraction during pressing, the potential of a micro-pressing technique using a instrumented micro press adapted to quantities of seeds as low as 10 g for rapeseed and 3 g for Arabidopsis thaliana was examined and discussed. Using a phenomenological model, data from the pressing process and the material behaviour (compressibility modules were obtained with a good precision, highlighting small differences between samples. The well-known positive effect of the temperature on the oil extraction yield was confirmed with A. thaliana. Micro-pressing of ground and cooked rapeseed seeds did not lead to the results usually reported in the literature for continuous pressing. The results strongly suggest that the performance of the static micro-pressing is related to the macro-and micro-structure of seeds and is less sensitive to the moisture than continuous pressing. Further experiments are needed to confirm that the micro-pressing could be an effective tool for predicting the extractability of oil and therefore, contribute to plant breeding programmes in the future.

  19. Parametric optimization of rice bran oil extraction using response surface methodology

    Directory of Open Access Journals (Sweden)

    Ahmad Syed W.

    2016-09-01

    Full Text Available Use of bran oil in various edible and nonedible industries is very common. In this research work, efficient and optimized methodology for the recovery of rice bran oil has been investigated. The present statistical study includes parametric optimization, based on experimental results of rice bran oil extraction. In this study, three solvents, acetone, ethanol and solvent mixture (SM [acetone: ethanol (1:1 v/v] were employed in extraction investigations. Response surface methodology (RSM, an optimization technique, was exploited for this purpose. A five level central composite design (CCD consisting four operating parameter, like temperature, stirring rate, solvent-bran ratio and contact time were examined to optimize rice bran oil extraction. Experimental results showed that oil recovery can be enhanced from 71% to 82% when temperature, solvent-bran ratio, stirring rate and contact time were kept at 55°C, 6:1, 180 rpm and 45 minutes, respectively while fixing the pH of the mixture at 7.1.

  20. Production of rapeseed oil fuel in decentralized oil extraction plants. Handbook. 2. new rev. and enl. ed.; Herstellung von Rapsoelkraftstoff in dezentralen Oelgewinnungsanlagen. Handbuch

    Energy Technology Data Exchange (ETDEWEB)

    Remmele, Edgar [Technologie- und Foerderzentrum (TFZ) im Kompetenzzentrum fuer Nachwachsende Rohstoffe, Straubing (Germany)

    2009-11-15

    Increasing oil prices, the dependence on petroleum imports and the desire to reduce the CO{sub 2} emissions, are arguments to accelerate the production and utilization of biofuels. In 2007, 3.3 million tons of biodiesel and 772,000 tons of vegetable oil were used as fuel. The technically and economically successful production of rapeseed oil fuel in decentralized oil mills requires a quality assurance. Specifically, the brochure under consideration reports on the following: (1) Oilseed processing; (2) Centralized oil production in Germany; (3) Design of a decentralized oil mill; (4) Production of rapeseed oil fuel in decentralized systems; (5) Quality assurance for rapeseed oil fuel in decentralized oil mills; (6) Properties of rapeseed oil fuel; (7) Quality of rapeseed oil fuel from decentralized oil mills; (8) Economic aspects of decentralized oil extraction; (9) Legal framework conditions.

  1. Optimization of ultrasonic-assisted extraction of pomegranate (Punica granatum L.) seed oil.

    Science.gov (United States)

    Tian, Yuting; Xu, Zhenbo; Zheng, Baodong; Martin Lo, Y

    2013-01-01

    The effectiveness of ultrasonic-assisted extraction (UAE) of pomegranate seed oil (PSO) was evaluated using a variety of solvents. Petroleum ether was the most effective for oil extraction, followed by n-hexane, ethyl acetate, diethyl ether, acetone, and isopropanol. Several variables, such as ultrasonic power, extraction temperature, extraction time, and the ratio of solvent volume and seed weight (S/S ratio) were studied for optimization using response surface methodology (RSM). The highest oil yield, 25.11% (w/w), was obtained using petroleum ether under optimal conditions for ultrasonic power, extraction temperature, extraction time, and S/S ratio at 140 W, 40 °C, 36 min, and 10 ml/g, respectively. The PSO yield extracted by UAE was significantly higher than by using Soxhlet extraction (SE; 20.50%) and supercriti cal fluid extraction (SFE; 15.72%). The fatty acid compositions were significantly different among the PSO extracted by Soxhlet extraction, SFE, and UAE, with punicic acid (>65%) being the most dominant using UAE. Copyright © 2012 Elsevier B.V. All rights reserved.

  2. Heating Quality and Stability of Aqueous Enzymatic Extraction of Fatty Acid-Balanced Oil in Comparison with Other Blended Oils

    Directory of Open Access Journals (Sweden)

    Yang Li

    2014-01-01

    Full Text Available The heating performance of enzyme-assisted aqueous processing-extracted blended oil (EAEPO, hexane-extracted blended oil (HEBO, and three kinds of blended oils was investigated by varying the heating times. Oil degradation was monitored by analysis of the acid value (AV, peroxide value (PV, p-anisidine value (p-AV, color, and trans-fatty acid composition. The fatty acid ratios of EAEPO, HEBO, and the three kinds of blended oils were very similar (0.27 : 1.03 : 0.96, 0.27 : 1.08 : 1.16, 0.27 : 0.65 : 0.8, 0.27 : 0.6 : 0.84, and 0.27 : 0.61 : 0.79, resp.. The AV and color increased in proportion to the heating time for all the oils. There was a rapid increase in the PV and p-AV of EAEPO and HEBO after heating for only 1 h, whereas the other three blended oils showed a rapid increase after heating for 2 h or 6 h. Despite the highest trans-fatty acid content found for HEBO, this content was relatively low and remained low up to a heating time of 8 h. It was found that after heating, a fatty acid ratio relatively close to its ideal value (0.27 : 0.48 : 0.49 was maintained by EAEPO, which indicates that EAEPO is tolerant to heat treatment and is suitable for maintaining a healthy diet.

  3. Extraction of oil and minor lipids from cold-press rapeseed cake with supercritical CO2

    Directory of Open Access Journals (Sweden)

    E. Uquiche

    2012-09-01

    Full Text Available This study examines the extraction of oil from cold-press rapeseed cake using Supercritical CO2(SC-CO2. The effects of pressure (20, 30, and 40 MPa, temperature (40, 50, and 60 ºC, and extraction time (60, 90, and 120 min on oil yield and composition (tocopherols and carotenoids were studied using response surface design. The results indicated that pressure influenced the most the yield of oil, followed by temperature and extraction time. Extraction time had no effect on oil composition. Extraction pressure and temperature did not affect the tocopherol concentration of the oil to a great extent, whereas temperature had no affect in its carotenoid concentration. A comparison was made between the relative qualities of oil extracted with SC-CO2at 40 MPa and 60 ºC and with n-hexane. Neither solvent affected the unsaponifiable matter content or the composition of phytosterols (mainly β-sitosterol, campesterol and brassicasterol of the oils, although there was a significant difference (p<0.05 in tocopherol. Extraction with SC-CO2at 40 MPa and 60 ºC is recommended to obtain rapeseed-oil enriched with tocopherols and carotenoids as important functional components.

  4. Impact of industrial hammer mill rotor speed on extraction efficiency and quality of extra virgin olive oil.

    Science.gov (United States)

    Polari, Juan J; Garcí-Aguirre, David; Olmo-García, Lucía; Carrasco-Pancorbo, Alegría; Wang, Selina C

    2018-03-01

    Crushing is a key step during olive oil extraction. Among commercial crushers, the hammer mill is the most widely used due to its robustness and high throughput. In the present work, the impact of hammer mill rotor speed on extraction yield and overall quality of super-high-density Arbosana olive oils were assessed in an industrial facility. Our results show that increasing the rotor speed from 2400rpm to 3600rpm led to a rise in oil yield of 1.2%, while conserving quality parameters. Sensory analysis showed more pungency with increased rotation speed, while others attributes were unaffected. Volatile compounds showed little variation with the differences in crusher speed; however, total phenols content, two relevant secoiridoids, and triterpenoids levels increased with rotor speed. Hammer mill rotor speed is a processing variable that can be tuned to increase the extraction efficiency and modulate the chemical composition of extra virgin olive oil. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. 3D confocal Raman imaging of oil-rich emulsion from enzyme-assisted aqueous extraction of extruded soybean powder.

    Science.gov (United States)

    Wu, Longkun; Wang, Limin; Qi, Baokun; Zhang, Xiaonan; Chen, Fusheng; Li, Yang; Sui, Xiaonan; Jiang, Lianzhou

    2018-05-30

    The understanding of the structure morphology of oil-rich emulsion from enzyme-assisted extraction processing (EAEP) was a critical step to break the oil-rich emulsion structure in order to recover oil. Albeit EAEP method has been applied as an alternative way to conventional solvent extraction method, the structure morphology of oil-rich emulsion was still unclear. The current study aimed to investigate the structure morphology of oil-rich emulsion from EAEP using 3D confocal Raman imaging technique. With increasing the enzymatic hydrolysis duration from 1 to 3 h, the stability of oil-rich emulsion was decreased as visualized in the 3D confocal Raman images that the protein and oil were mixed together. The subsequent Raman spectrum analysis further revealed that the decreased stability of oil-rich emulsion was due to the protein aggregations via SS bonds or protein-lipid interactions. The conformational transfer in protein indicated the formation of a compact structure. Copyright © 2017 Elsevier Ltd. All rights reserved.

  6. Determination of solvent concentration-dependent dispersion in the vapor extraction (VAPEX) process

    Energy Technology Data Exchange (ETDEWEB)

    Abukhalifeh, H.; Lohi, A.; Upreti, S. [Ryerson Polytechnic Univ., Toronto, ON (Canada)

    2008-07-01

    This paper presented the results of a computational algorithm that revealed the optimal conditions required for vapor extraction (VAPEX) for a solvent gas-heavy oil system. VAPEX is a promising recovery process because it requires low energy use and emits fewer greenhouse gases to the atmosphere compared to other enhanced oil recovery methods. The process is governed by the dispersion of solvent gases into heavy oil and bitumen. As such, it is essential to accurately determine solvent dispersion in VAPEX in order to effectively predict the amount and time scale of oil recovery, and to optimize field operations. VAPEX experiments were conducted in this study to determined the dispersion coefficient of a solvent as a function of its concentration in heavy oil and bitumen. The principles of variational calculus were used together with a mass transfer model of the experimental process. It was concluded that the oil production determined by the model should agree with its experimental counterpart, given the optimal gas dispersion versus concentration function.

  7. Supercritical CO2 extraction of oil and omega-3 concentrate from Sacha inchi (Plukenetia volubilis L. from Antioquia, Colombia

    Directory of Open Access Journals (Sweden)

    D. M. Triana-Maldonado

    2017-03-01

    Full Text Available Sacha inchi (Plukenetia volubilis L. seeds were employed for oil extraction with supercritical CO2 at laboratory scale. The supercritical extraction was carried out at a temperature of 60 °C, pressure range of 400–500 bars and CO2 flow of 40–80 g/min. The maximum recovery was 58% in 180 min, favored by increasing the residence time of CO2 in the extraction tank. Subsequently, the process was evaluated at pilot scale reaching a maximum recovery of 60% in 105 min, with a temperature of 60 °C, pressure of 450 bars and CO2 flow of 1270 g/min. The fatty acid composition of the oil was not affected for an extraction period of 30–120 min. The Sacha inchi oil was fractionated with supercritical CO2 to obtain an omega-3 concentrate oil without finding a considerable increase in the proportion of this compound, due to the narrow range in the carbon number of fatty acids present in the oil (16–18 carbons, making it difficult for selective separation.

  8. Supercritical CO2 extraction of oil and omega-3 concentrate from Sacha inchi (Plukenetia volubilis L.) from Antioquia, Colombia

    International Nuclear Information System (INIS)

    Torijano-Gutiérrez, S.A.; Triana-Maldonadoa, D.M.; Giraldo-Estradaa, C.

    2017-01-01

    Sacha inchi (Plukenetia volubilis L.) seeds were employed for oil extraction with supercritical CO2 at laboratory scale. The supercritical extraction was carried out at a temperature of 60 °C, pressure range of 400–500 bars and CO2 flow of 40–80 g/min. The maximum recovery was 58% in 180 min, favored by increasing the residence time of CO2 in the extraction tank. Subsequently, the process was evaluated at pilot scale reaching a maximum recovery of 60% in 105 min, with a temperature of 60 °C, pressure of 450 bars and CO2 flow of 1270 g/min. The fatty acid composition of the oil was not affected for an extraction period of 30–120 min. The Sacha inchi oil was fractionated with supercritical CO2 to obtain an omega-3 concentrate oil without finding a considerable increase in the proportion of this compound, due to the narrow range in the carbon number of fatty acids present in the oil (16–18 carbons), making it difficult for selective separation. [es

  9. The removal of metals from edible oil by a membrane extraction procedure 355

    NARCIS (Netherlands)

    Keurentjes, J.T.F.; Bosklopper, T.G.J.; Dorp, van L.J.; Riet, van 't K.

    1990-01-01

    Edible oils may contain traces of metals. In oil refining procedures these metals have to be removed to guarantee oxidatively stable products. In this study we present a hollow fiber membrane extraction system for the removal of metals from an oil. Several extraction liquids were tested, of which an

  10. Research to commercialization: Technology transfer gaharu oil extraction to people of Orang Asli Kampung Kedaik, Rompin, Pahang

    International Nuclear Information System (INIS)

    Mohd Fajri Osman; Shyful Azizi Abdul Rahman; Chong, Saw Peng; Muhammad Lebai Juri; Mat Rasol Awang

    2010-01-01

    Nuclear Malaysia has been involved in research related to gaharu since 2004 again. Studies conducted in the fields of agronomy, breeding, inoculation, grading, processing and development of quality agar wood products. Agar wood research involves application of nuclear technology and related technologies according to the expertise of researchers in the Malaysian Nuclear Agency in the developing industrial modernization and technology goals gaharu in Malaysia. In a study of the development process and product quality of agar wood, sandalwood oil processing technologies have been researched and developed at Nuclear Malaysia. Demand for sandalwood oil extraction technology development is very high because of sandalwood oil is very high-value products with the price can go up to RM 60,000.00 per kilogram. With the knowledge, technology innovation resulting from research and experience, the Malaysian Nuclear Agency was to transfer technology and knowledge of processing sandalwood oil to the community through a project of Development Projects in Agar wood Oil Extraction Plant Relocation Plan Aboriginal Kg Kedaik, Rompin, Pahang financial assistance from the Ministry of Science, Technology and Innovation under grant Community Innovation Fund (CIF). Technology transfer and travel through the various steps of the project which involves the preparation of papers, technology feasibility study to the community, the strength of community, sustainability research projects, effectiveness, success and benefits gained. (author)

  11. The antibacterial and antifungal activity of essential oils extracted from Guatemalan medicinal plants.

    Science.gov (United States)

    Miller, Andrew B; Cates, Rex G; Lawrence, Michael; Soria, J Alfonso Fuentes; Espinoza, Luis V; Martinez, Jose Vicente; Arbizú, Dany A

    2015-04-01

    Essential oils are prevalent in many medicinal plants used for oral hygiene and treatment of diseases. Medicinal plant species were extracted to determine the essential oil content. Those producing sufficient oil were screened for activity against Staphylococcus aureus, Escherichia coli, Streptococcus mutans, Lactobacillus acidophilus, and Candida albicans. Plant samples were collected, frozen, and essential oils were extracted by steam distillation. Minimum inhibitory concentrations (MIC) were determined using a tube dilution assay for those species yielding sufficient oil. Fifty-nine of the 141 plant species produced sufficient oil for collection and 12 species not previously reported to produce essential oils were identified. Essential oil extracts from 32 species exhibited activity against one or more microbes. Oils from eight species were highly inhibitory to S. mutans, four species were highly inhibitory to C. albicans, and 19 species yielded MIC values less than the reference drugs. RESULTS suggest that 11 species were highly inhibitory to the microbes tested and merit further investigation. Oils from Cinnamomum zeylanicum Blume (Lauraceae), Citrus aurantiifolia (Christm.) Swingle (Rutaceae), Lippia graveolens Kunth (Verbenaceae), and Origanum vulgare L. (Lamiaceae) yielded highly significant or moderate activity against all microbes and have potential as antimicrobial agents. Teas prepared by decoction or infusion are known methods for extracting essential oils. Oils from 11 species were highly active against the microbes tested and merit investigation as to their potential for addressing health-related issues and in oral hygiene.

  12. Microalgae based biorefinery: evaluation of oil extraction methods in terms of efficiency, costs, toxicity and energy in lab-scale

    Directory of Open Access Journals (Sweden)

    Ángel Darío González-Delgado

    2013-06-01

    Full Text Available Several alternatives of microalgal metabolites extraction and transformation are being studied for achieving the total utilization of this energy crop of great interest worldwide. Microalgae oil extraction is a key stage in microalgal biodiesel production chains and their efficiency affects significantly the global process efficiency. In this study, a comparison of five oil extraction methods in lab-scale was made taking as additional parameters, besides extraction efficiency, the costs of method performing, energy requirements, and toxicity of solvents used, in order to elucidate the convenience of their incorporation to a microalgae-based topology of biorefinery. Methods analyzed were Solvent extraction assisted with high speed homogenization (SHE, Continuous reflux solvent extraction (CSE, Hexane based extraction (HBE, Cyclohexane based extraction (CBE and Ethanol-hexane extraction (EHE, for this evaluation were used the microalgae strains Nannochloropsis sp., Guinardia sp., Closterium sp., Amphiprora sp. and Navicula sp., obtained from a Colombian microalgae bioprospecting. In addition, morphological response of strains to oil extraction methods was also evaluated by optic microscopy. Results shows that although there is not a unique oil extraction method which excels in all parameters evaluated, CSE, SHE and HBE appears as promising alternatives, while HBE method is shown as the more convenient for using in lab-scale and potentially scalable for implementation in a microalgae based biorefinery

  13. Bactericidal activity of herbal volatile oil extracts against multidrug-resistant Acinetobacter baumannii.

    Science.gov (United States)

    Intorasoot, Amornrat; Chornchoem, Piyaorn; Sookkhee, Siriwoot; Intorasoot, Sorasak

    2017-01-01

    The aim of the study is to investigate the antibacterial activity of 10 volatile oils extracted from medicinal plants, including galangal ( Alpinia galanga Linn.), ginger ( Zingiber officinale ), plai ( Zingiber cassumunar Roxb.), lime ( Citrus aurantifolia ), kaffir lime ( Citrus hystrix DC.), sweet basil ( Ocimum basilicum Linn.), tree basil ( Ocimum gratissimum ), lemongrass ( Cymbopogon citratus DC.), clove ( Syzygium aromaticum ), and cinnamon ( Cinnamomum verum ) against four standard strains of Staphylococcus aureus , Escherichia coli , Pseudomonas aeruginosa , Acinetobacter baumannii , and 30 clinical isolates of multidrug-resistant A. baumannii (MDR- A. baumannii ). Agar diffusion, minimum inhibitory concentration, and minimum bactericidal concentration (MBC) were employed for the determination of bactericidal activity of water distilled medicinal plants. Tea tree oil ( Melaleuca alternifolia ) was used as positive control in this study. The results indicated the volatile oil extracted from cinnamon exhibited potent antibacterial activity against the most common human pathogens, S. aureus , E. coli , P. aeruginosa , and A. baumannii . Most of volatile oil extracts were less effective against non-fermentative bacteria, P. aeruginosa . In addition, volatile oil extracted from cinnamon, clove, and tree basil possessed potent bactericidal activity against MDR- A. baumannii with MBC 90 of 0.5, 1, and 2 mg/mL, respectively. The volatile oil extracts would be useful as alternative natural product for the treatment of the most common human pathogens and MDR- A. baumannii infections.

  14. Comparison between different liquid-liquid and solid phase methods of extraction prior to the identification of the phenolic fraction present in olive oil washing wastewater from the two-phase olive oil extraction system

    Directory of Open Access Journals (Sweden)

    S. Jiménez-Herrera

    2017-09-01

    Full Text Available Phenolic compounds from olive mill wastewater (OMW, are characterized by a strong antioxidant activity. At the same time, they represent an environmental problem because they are difficult to degrade. The purpose of this work was to identify these biologically active compounds in the OMW from two-phase olive oil production in order to convert a polluting residue into a source of natural antioxidants. After optimizing the extraction process of phenolic compounds using liquid-liquid extraction (LLE and solid phase extraction (SPE methods, it was determined that the most appropriate sequence comprised a previous centrifugation to remove the lipid fraction, followed by liquid extraction with ethyl acetate or SPE. The most important compounds identified in olive oil washing wastewater (OOWW were tyrosol, hydroxytyrosol and succinic acid; whereas the ones in the wastewater derived from the washing of the olives (OWW were cresol, catechol, 4-methylcatechol, hydrocinnamic acid and p-hydroxy-hydrocinnamic acid.

  15. Comparison between different liquid-liquid and solid phase methods of extraction prior to the identification of the phenolic fraction present in olive oil washing wastewater from the two-phase olive oil extraction system

    International Nuclear Information System (INIS)

    Jiménez-Herrera, S.; Ochando-Pulido, J.M.; Martínez-Ferez, A.

    2017-01-01

    Phenolic compounds from olive mill wastewater (OMW), are characterized by a strong antioxidant activity. At the same time, they represent an environmental problem because they are difficult to degrade. The purpose of this work was to identify these biologically active compounds in the OMW from two-phase olive oil production in order to convert a polluting residue into a source of natural antioxidants. After optimizing the extraction process of phenolic compounds using liquid-liquid extraction (LLE) and solid phase extraction (SPE) methods, it was determined that the most appropriate sequence comprised a previous centrifugation to remove the lipid fraction, followed by liquid extraction with ethyl acetate or SPE. The most important compounds identified in olive oil washing wastewater (OOWW) were tyrosol, hydroxytyrosol and succinic acid; whereas the ones in the wastewater derived from the washing of the olives (OWW) were cresol, catechol, 4-methylcatechol, hydrocinnamic acid and p-hydroxy-hydrocinnamic acid. [es

  16. Predicting the supercritical carbon dioxide extraction of oregano bract essential oil

    Directory of Open Access Journals (Sweden)

    Abdolreza Moghadassi

    2011-10-01

    Full Text Available The extraction of essential oils using compressed carbon dioxide is a modern technique offering significant advantagesover more conventional methods, especially in particular applications. The prediction of extraction efficiency is a powerful toolfor designing and optimizing the process. The current work proposed a new method based on the artificial neural network(ANN for the estimation of the extraction efficiency of the essential oil oregano bract. In addition, the work used the backpropagationlearning algorithm, incorporating different training methods. The required data were collected; pre-treating wasused for ANN training. The accuracy and trend stability of the trained networks were verified according to their ability to predictunseen data. The Levenberg-Marquardt algorithm has been found to be the most suitable algorithm, with the appropriatenumber of neurons (i.e., ten neurons in the hidden layer and a minimum average absolute relative error (i.e., 0.019164. Inaddition, some excellent predictions with maximum error of 0.039313 were observed. The results demonstrated the ANN’scapability to predict the measured data. The ANN model performance was also compared to a suitable mathematical model,thereby confirming the superiority of the ANN model.

  17. Effects of high-pressure process on kinetics of leaching oil from soybean powder using hexane in batch systems.

    Science.gov (United States)

    Uhm, Joo Tae; Yoon, Won Byong

    2011-08-01

    Mass transfer models of leaching oil from soybean (Glycine max) flour with hexane after high-pressure process (HPP) treatment were developed. High pressure (450 MPa) was applied to the soybean flour (mean diameter of flour particle: 365 μm) for 30 min before leaching the oil components in the solvent. The ratio of solvent (volume, mL) to soybean flour (mass, g), such as 1:10 and 1:20, was employed to characterize the effect of solvent ratio on the leaching rate in the batch type of extraction process. Ultraviolet absorbance at 300 nm was used to monitor the extraction rate. Saturation solubility (C(AS)) was determined to be 21.73 kg/m³. The mass transfer coefficients (k) were determined based on the 1st- and 2nd-order kinetic models. The 2nd kinetic model showed better fit. The HPP treatment showed a higher extraction rate and yield compared to the control, while the amount of solvent did not affect the extraction rate and yield. The scanning electron microscope showed that HPP-treated soybean particles included more pores than the untreated. The pores observed in the HPP-treated soybean flours might help increase the mass transfer rate of solvent and solute in the solid matrix. High-pressure processing can help increase the extraction rate of oil from the soybean flour operated in batch systems. The conventional solid to solvent ratio (1:20) used to extract oil composition from the plant seed did not help increase the amount of oil extracted from the soybean flour. © 2011 Institute of Food Technologists®

  18. Oil extraction from olive foot cake with acidic hexane

    Directory of Open Access Journals (Sweden)

    Kmieciak, S.

    1991-02-01

    Full Text Available The use of acidic hexane as a solvent increases the extracted oil yield from olive foot cake. Two extraction procedures are studied: open air extraction at room temperature and Soxhlet exhaustive extraction. The additional yield is about 5% for a 2.5% acetic acid content in case of open air extraction and turns out to be 9% for 7.5% acetic acid content in the Soxhlet procedure. An analysis of the extracted oil shows a light increase of the acidity of oil. The improved yield may be attributed to the action of acetic acid on the decomposition of intercellular structures and binding of some polar lipids. The phospholipids content of oil extracted with 7.5% acidic hexane is found to be 25 times more than with pure hexane.

    El uso de hexano ácido como disolvente aumenta el rendimiento de aceite extraído de orujo de aceituna. Se han estudiado dos procedimientos de extracción: extracción al aire libre a temperatura ambiente y extracción exhaustiva en Soxhlet. En el caso de extracción al aire libre el rendimiento adicional es alrededor del 5% para un contenido del 2'5% en ácido acético y llega a ser en el procedimiento en Soxhlet del 9% para un contenido en ácido acético del 7'5%. Un análisis del aceite extraído mostró un ligero aumento de la acidez del aceite. La mejora del rendimiento puede ser atribuida a la acción del ácido acético sobre la descomposición de estructuras intercelulares y uniones de lípidos polares. Se ha encontrado que el contenido en fosfolípidos del aceite extraído con el 7*5% de hexano ácido es 25 veces mayor que con hexano puro.

  19. Antitumor effects and mechanisms of Ganoderma extracts and spores oil

    OpenAIRE

    Chen, Chun; Li, Peng; Li, Ye; Yao, Guan; Xu, Jian-Hua

    2016-01-01

    Ganoderma lucidum is a popular herbal medicine used in China to promote health. Modern studies have disclosed that the active ingredients of Ganoderma can exhibit several effects, including antitumor effects and immunomodulation. The present study evaluated the antitumor effects of self-prepared Ganoderma extracts and spores oil, and investigated the possible underlying mechanisms by observing the effects of the extracts and oil on topoisomerases and the cell cycle. The results showed that Ga...

  20. Antimicrobial potential of leaf and fruit extracts and oils of wild and cultivated edible olive

    International Nuclear Information System (INIS)

    Hussain, A.; Qurshi, I.A.; Liaqat, R.; Akhtar, S.; Aziz, I.

    2014-01-01

    Olive tree is the first botanical noted in the Bible. Leaves and fruits of olive are rich sources of Phenols, triterpenes, and flavanoids. Oleuropein obtained from the leaves extract is believed to be important therapeutic compound. Olive leaf and oils are used for the treatment of different diseases as folklore medicines by different ethnic groups in different countries of the world. The present study aims to investigate the potential antimicrobial activities of wild (Olea ferruginea) and edible (Olea europaea) olive leaf crude extracts, crude oils from ripe and unripe fruits and extra virgin oils against the selected gram positive and gram negative bacterial strains. The results show that olive leaf and oil have potential antibacterial activities against some of the gram positive and gram negative bacterial strains. However, certain strains were resistant to the extracts. It was also found that the activities were higher for the gram negative strains as compared to gram positive strains. The methanolic and ethanolic extracts were found to be more efficient in extraction than the other solvents used. Leaf extracts were more effective than the oil extracted from ripe and unripe fruits. There was no significant difference in the activities of extra virgin oils and crude leaf extracts. From the results it is concluded that the leaf extract is a cheap and effective antibacterial agent that can be used as alternative to purified oil. (author)

  1. Ethanol production from lignocellulosic byproducts of olive oil extraction.

    Science.gov (United States)

    Ballesteros, I; Oliva, J M; Saez, F; Ballesteros, M

    2001-01-01

    The recent implementation of a new two-step centrifugation process for extracting olive oil in Spain has substantially reduced water consumption, thereby eliminating oil mill wastewater. However, a new high sugar content residue is still generated. In this work the two fractions present in the residue (olive pulp and fragmented stones) were assayed as substrate for ethanol production by the simultaneous saccharification and fermentation (SSF) process. Pretreatment of fragmented olive stones by sulfuric acid-catalyzed steam explosion was the most effective treatment for increasing enzymatic digestibility; however, a pretreatment step was not necessary to bioconvert the olive pulp into ethanol. The olive pulp and fragmented olive stones were tested by the SSF process using a fed-batch procedure. By adding the pulp three times at 24-h intervals, 76% of the theoretical SSF yield was obtained. Experiments with fed-batch pretreated olive stones provided SSF yields significantly lower than those obtained at standard SSF procedure. The preferred SSF conditions to obtain ethanol from olives stones (61% of theoretical yield) were 10% substrate and addition of cellulases at 15 filter paper units/g of substrate.

  2. Optimization of palm oil extraction from Decanter cake of small crude palm oil mill by aqueous surfactant solution using RSM

    Science.gov (United States)

    Ahmadi Pirshahid, Shewa; Arirob, Wallop; Punsuvon, Vittaya

    2018-04-01

    The use of hexane to extract vegetable oil from oilseeds or seed cake is of growing concern due to its environmental impact such as its smelling and toxicity. In our method, used Response Surface Methodology (RSM) was applied to study the optimum condition of decanter cake obtained from small crude palm oil with aqueous surfactant solution. For the first time, we provide an optimum condition of preliminary study with decanter cake extraction to obtain the maximum of oil yield. The result from preliminary was further used in RSM study by using Central Composite Design (CCD) that consisted of thirty experiments. The effect of four independent variables: the concentration of Sodium Dodecyl Sulfate (SDS) as surfactant, temperature, the ratio by weight to volume of cake to surfactant solution and the amount of sodium chloride (NaCl) on dependent variables are studied. Data were analyzed using Design-Expert 8 software. The results showed that the optimum condition of decanter cake extraction were 0.016M of SDS solution concentration, 73°C of extraction temperature, 1:10 (g:ml) of the ratio of decanter cake to SDS solution and 2% (w/w) of NaCl amount. This condition gave 77.05% (w/w) oil yield. The chemical properties of the extracted palm oil from this aqueous surfactant extraction are further investigated compared with the hexane extraction. The obtained result showed that all properties of both extractions were nearly the same.

  3. Microwave-assisted extraction of Nigella sativa L. essential oil and evaluation of its antioxidant activity.

    Science.gov (United States)

    Abedi, Abdol-Samad; Rismanchi, Marjan; Shahdoostkhany, Mehrnoush; Mohammadi, Abdorreza; Mortazavian, Amir Mohammad

    2017-11-01

    It has been previously reported that the essential oil of Nigella sativa L. seeds and its major active component, thymoquinone (TQ), possess a broad variety of biological activities and therapeutic properties. In this work, microwave-assisted extraction (MAE) of the essential oil from Nigella sativa L. seeds and its antioxidant activity were studied. Response surface methodology based on central composite design was used to evaluate the effects of extraction time, irradiation power and moisture content on extraction yield and TQ content. Optimal parameters obtained by CCD and RSM were extraction time 30 min, irradiation power 450 W, and moisture content 50%. The extraction yield and TQ content of the essential oil were 0.33 and 20% under the optimum conditions, respectively. In contrast, extraction yield and TQ amount of oil obtained by hydrodistillation (HD) were 0.23 and 3.71%, respectively. The main constituents of the essential oil extracted by MAE and HD were p -cymene, TQ, α-thujene and longifolene, comprising more than 60% of total peak area. The antioxidant capacity of essential oils extracted by different methods were evaluated using 2,2-diphenyl-1-picrylhydrazyl and Ferric reducing antioxidant power assays, and compared with traditional antioxidants. The results showed that MAE method was a viable alternative to HD for the essential oil extraction from N. sativa seeds due to the excellent extraction efficiency, higher thymoquinone content, and stronger antioxidant activity.

  4. In vitro antibacterial effects of five volatile oil extracts against intramacrophage Brucella abortus 544.

    Science.gov (United States)

    Al-Mariri, Ayman; Saour, George; Hamou, Razan

    2012-06-01

    Brucellaabortus is a gram-negative facultative intracellular bacterium that can cause a highly contagious disease in sheep, goats, cattle and one-humped camels. It is responsible for one of the most important zoonosis in human. The aim of this study was to evaluate the role of Mentha piperita, Origanum majorana, Citrus lemon, Cinnamomum verum and Myristica fragrans essential volatile oil extracts on human macrophages infected by B. abortus 544. Essential volatile oil extracts from M. piperita, O. majorana, C. lemon, C. verum and M. fragrans were extracted. Human macrophages were cultured at a density of 2×10(5) cells per well in sterile 96-well microtiter plates, and infected with B. abortus 544 at a ratio of 1:100 bacteria/cell. Then essential volatile oil extracts were added at a concentration of 1%. At specified times; cells were washed, lysed with 0.1% Triton, and plated on 2YT agar to determine the number of intracellular bacteria. Cinnamomum verum volatile oil at a concentration of 1% had the highest antibacterial activity against B. abortus 544 inside human macrophages. Its inhibitory effect observed from 24 h and continued till 144 h after the infection. Moreover, C. verum (0.1%) in combination with 1% concentration of M. piperita, O. majorana, C. lemon or M. fragrans volatile oil extracts produced a synergistic inhibitory effect against B. abortus 544. The results indicate that, among the five selected oil extracts, C. verum volatile oil applied either separately or in combination with other oil extracts had the most effective antimicrobial activity against Brucella.

  5. Essential oil extraction with concentrating solar thermal energy

    OpenAIRE

    Veynandt, François

    2015-01-01

    Material complementari del cas estudi "Essential oil extraction with concentrating solar thermal energy”, part component del llibre "Case studies for developing globally responsible engineers" Peer Reviewed

  6. Extraction of Thyme Oil: Comparison between Hydrodistillation and Supercritical CO2 Extraction

    Czech Academy of Sciences Publication Activity Database

    Aleksovski, S. A.; Sovová, Helena; Poposka, F. A.

    2001-01-01

    Roč. 51, č. 4 (2001), s. 305-310 ISSN 1330-0075 Institutional research plan: CEZ:AV0Z4072921 Keywords : thymus serpyllum * supercritical fluid extraction * assential oil Subject RIV: CI - Industrial Chemistry, Chemical Engineering

  7. Bactericidal activity of herbal volatile oil extracts against multidrug resistant Acinetobacter baumannii

    Directory of Open Access Journals (Sweden)

    Amornrat Intorasoot

    2017-06-01

    Full Text Available Aim:\tTo investigate the antibacterial activity of ten volatile oils extracted from medicinal plants, including galangal (Alpinia galanga Linn., ginger (Zingiber officinale, plai (Zingiber cassumunar Roxb., lime (Citrus aurantifolia, kaffir lime (Citrus hystrix DC., sweet basil (Ocimum basilicum Linn., tree basil (Ocimum gratissimum, lemongrass (Cymbopogon citratus DC., clove (Syzygium aromaticum and cinnamon (Cinnamomum verum against four standard strains of Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, Acinetobacter baumannii and thirty clinical isolates of multidrug-resistant A. baumannii (MDR-A. baumannii. Methods:\tAgar diffusion, minimal inhibitory concentration (MIC and minimal bactericidal concentration (MBC were employed for determination of bactericidal activity of water distillated medicinal plants. Tea tree oil (Melaleuca alternifolia was used as positive control in this study. Results:\tThe results indicated the volatile oil extracted from cinnamon exhibited potent antibacterial activity against the most common human pathogens, S. aureus, E. coli, P. aeruginosa and A. baumannii. Most of volatile oil extracts were less effective against non-fermentative bacteria, P. aeruginosa. In addition, volatile oil extracted from cinnamon, clove and tree basil possessed potent bactericidal activity against MDR-A. baumannii with MBC90 of 0.5, 1 and 2 mg/mL, respectively. Conclusions: The volatile oil extracts would be useful as alternative natural product for treatment of the most common human pathogens and MDR-A. baumannii infections. [J Complement Med Res 2017; 6(2.000: 218-222

  8. Research Concerning Antimicrobial Activities of Some Essential Oils Extracted from Plants

    Directory of Open Access Journals (Sweden)

    ADRIANA DALILA CRISTE

    2014-10-01

    Full Text Available The principal components of some essential oils extracted from plants have been found to have microbial activity. Depending on the concentration, the members of this class are known to be bactericide or bacteriostatic. Their action mechanism is unclear, but some studies suggest that the compounds penetrate the cell, where they interfere with cellular metabolism. The purpose of this study was to evaluate the antimicrobial activity of 5 essential oils extracted from plants on Escherichia coli, Pseudomonas aeruginosa, Salmonella enterica, Staphylococcus aureus and Bacillus cereus and to determinate how different amount of the used oils can influence the results of inhibition tests. These results showed that mainly all the natural extracts presented an antimicrobial effect. Thereby, some extracts were more efficient than another and the order is: Eucalyptus globulus (eucalyptus, Mentha piperita (mint, Lavandula angustifolia (lavender, Matricaria chamomilla (chamomile, Calendula officinalis (calendula.

  9. Effects of oil extracts of Eupatorium adenophorum on Phytophthora capsici and other plant pathogenic fungi in vitro.

    Science.gov (United States)

    Liu, Xiaoman; Ouyang, Canbin; Wang, Qiuxia; Li, Yuan; Yan, Dongdong; Yang, Dongsheng; Fang, Wensheng; Cao, Aocheng; Guo, Meixia

    2017-08-01

    The antifungal activity of oils extracted from Eupatorium adenophorum was tested against five phytopathogens in vitro. Oil extracts inhibited the mycelial growth of Phytophthora capsici which causes phytophthora blight in pepper. The minimum inhibitory concentration of oils against P. capsici was 500μg/ml after 7days incubation. At the ultrastructural level, oil extracts caused complete disorganization of intracellular organelles, cytoplasm depletion, disruption of cytoplasmic membranes and the cell wall. Membrane permeability increased with the increasing concentration of oil extracts. These results suggested that these oil extracts exhibited multiple modes of action including disruption of the cell membrane system. Furthermore, oil extracts combined with synthetic fungicides synergistically inhibited mycelial growth of P. capsici, which creates the possibility of reducing fungicide concentration needed to successfully control phytophthora blight in commercial pepper production. This study's use of multiple methods of analysis has increased our understanding of the mode of action of E. adenophorum oil extracts against P. capsici. Copyright © 2017. Published by Elsevier Inc.

  10. A continuum of research projects to improve extraction of oil and proteins in oilseed plants

    Directory of Open Access Journals (Sweden)

    Miquel Martine

    2011-05-01

    Full Text Available A key challenge in the actual context of fossil sources rarefaction, global warming, and of increase of the world global population, is to promote the use of molecules derived from renewable sources such as plants. Among these molecules, lipids and proteins are targets of interest. Plant lipids from oilseeds are attractive substitutes to the use of fossil oil. Till the beginning of the 20th century, numerous products used in the daily life were derived from natural renewable products. For instance, plant oil was commonly used as fuel for vehicles and was entering in the composition of paintings, lubricants etc. Unfortunately, natural oils have been progressively replaced by cheaper fossil oil in the fabrication of these products. Nowadays, fossil oils are becoming increasingly expensive being a finite comodity. It is thus important to reduce our dependence from fossil oil and develop substitution industries. Oilseeds contain important amounts of proteins which are mainly used in feed. As several kilograms of plant protein are needed to obtain one kilogram of animal protein, the interest toward using plant protein in food is reinforced. The developments of the use of plant lipids, as well as proteins are a major stakes for the competitiveness of European agriculture and industry, as well as for sustainable development. Extraction of oil and proteins from rapeseed has a significant cost, in term of energy and solvent uses, and finally affects the ultimate quality of the products (protein digestibility. In order to quantitatively extract seed reserves under mild conditions, it will be necessary to limit the amount of energy needed, and avoid any use of solvents. Ideally, seeds should be processed in a bio refinery. In this paper, we will describe how oilseeds store their reserves, and roadblocks for improving actual oilseed extraction processes. A continuum of research projects aimed at answering targeted questions will be presented, with selected

  11. Feasibility study for the installation of a nuclear reactor in thermal stimulation processes in heavy oil extraction from Orinoco oil belt

    International Nuclear Information System (INIS)

    Munoz, A.; Sanchez, R.

    1982-01-01

    Due to strategic need in the exploitation of heavy and extraheavy oil wells of Orinoco oil belt, technical and economical studies have been carried out to determine an optimal method for oil production and exploitation. So far, studies indicate thermal stimulation is the most adequate technique. Experience shows that stimulation cost is high when traditional methods (boilers) are used. The profit is due to the high price of oil in international market. Due to actual oil price trends, evaluation of nontraditional methods to generate steam in thermal stimulation processes (steam injection) is in order. A nuclear reactor as steam generator was evaluated. It was found economical feasibility and saving in fuel cost between 31.08% and 72.63% depending on oil prices

  12. An Investigation into the Physico-chemical Properties of Transformer Oil Blends with Antioxidants extracted from Turmeric Powder

    Science.gov (United States)

    Dukhi, Veresha; Bissessur, Ajay; Ngila, Catherine Jane; Ijumba, Nelson Mutatina

    2013-07-01

    The blending of transformer oil (used mainly as an insulating oil) with appropriate synthetic antioxidants, such as BHT (2,6-di-tert-butyl-4-methylphenol) and DBP (2,6-di-tert-butylphenol) have been previously reported. This article is focused on the use of antioxidant extracts from turmeric (Curcuma longa), a natural source. Turmeric is well known for its antimicrobial, antioxidant and anticarcinogenic properties owing to the active nature of its components. Extracts from powdered turmeric were subsequently blended into naphthenic-based uninhibited virgin transformer oil, hereinafter referred to as extract-oil blends (E-OB). Thin-layer chromatography (TLC) of the oil blends revealed that five components extracted from turmeric powder were successfully blended into the oil. Subsequent gas chromatography-mass spectrometry (GC-MS) analysis confirmed the presence of the compounds: curcumene, sesquiphellandrene, ar-turmerone, turmerone and curlone. Thermogravimetric analysis (TGA) of the extract-oil blends, containing various levels of extracts, revealed an average temperature shift of ˜8.21°C in the initial onset of degradation in comparison to virgin non-blended oil. The 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay showed that an increase in the mass aliquot of turmeric extracts in the transformer oil increased the free radical scavenging activity of the oil. Electrical properties of the oil investigated showed that the dissipation factor in the blended oil was found to be lower than that of virgin transformer oil. Evidently, a lower dissipation value renders the oil blend as a superior insulator over normal virgin non-blended oil. This investigation elucidated improved physico-chemical properties of transformer oil blended with turmeric antioxidant extracts.

  13. Analysis of the essential oils of Alpiniae Officinarum Hance in different extraction methods

    Science.gov (United States)

    Yuan, Y.; Lin, L. J.; Huang, X. B.; Li, J. H.

    2017-09-01

    It was developed for the analysis of the essential oils of Alpiniae Officinarum Hance extracted by steam distillation (SD), ultrasonic assisted solvent extraction (UAE) and supercritical fluid extraction (SFE) via gas chromatography mass spectrometry (GC-MS) combined with retention index (RI) method. There were multiple volatile components of the oils extracted by the three above-mention methods respectively identified; meanwhile, each one was quantified by area normalization method. The results indicated that the content of 1,8-Cineole, the index constituent, by SD was similar as SFE, and higher than UAE. Although UAE was less time consuming and consumed less energy, the oil quality was poorer due to the use of organic solvents was hard to degrade. In addition, some constituents could be obtained by SFE but could not by SD. In conclusion, essential oil of different extraction methods from the same batch of materials had been proved broadly similarly, however, there were some differences in composition and component ratio. Therefore, development and utilization of different extraction methods must be selected according to the functional requirements of products.

  14. Ultrasonic-Assisted Extraction of Raspberry Seed Oil and Evaluation of Its Physicochemical Properties, Fatty Acid Compositions and Antioxidant Activities.

    Directory of Open Access Journals (Sweden)

    Hui Teng

    Full Text Available Ultrasonic-assisted extraction was employed for highly efficient separation of aroma oil from raspberry seeds. A central composite design with two variables and five levels was employed and effects of process variables of sonication time and extraction temperature on oil recovery and quality were investigated. Optimal conditions predicted by response surface methodology were sonication time of 37 min and extraction temperature of 54°C. Specifically, ultrasonic-assisted extraction (UAE was able to provide a higher content of beneficial unsaturated fatty acids, whereas conventional Soxhlet extraction (SE resulted in a higher amount of saturated fatty acids. Moreover, raspberry seed oil contained abundant amounts of edible linoleic acid and linolenic acid, which suggest raspberry seeds could be valuable edible sources of natural γ-linolenic acid products. In comparison with SE, UAE exerted higher free radical scavenging capacities. In addition, UAE significantly blocked H2O2-induced intracellular reactive oxygen species (ROS generation.

  15. Flash Extraction and Physicochemical Characterization of Oil from Elaeagnus mollis Diels Seeds.

    Science.gov (United States)

    Kan, Lina; Wang, Lin; Ding, Qingzhen; Wu, Yanwen; Ouyang, Jie

    2017-04-03

    A flash extraction method was used to isolate Elaeagnus mollis oil (EMO). The optimal extraction parameters, sample/solvent ratio and extraction temperature, were determined to be 1:10 (g/mL) and 40°C, respectively. Especially, the extraction yield reached 49.30% when the extraction time was as short as 2 min. No obvious difference was observed in fatty acid composition, iodine value, saponification number, total phenolic content and tocopherol content between flash-extracted EMO and Soxhlet-extracted EMO, but their physicochemical values were lower than those of cold-pressed EMO. Cold-pressed EMO had higher oxidation stability, DPPH (1-diphenyl-2-picrylhydrazyl) and hydroxyl radical-scavenging activities than flash-extracted EMO and Soxlet extracted EMO. The flash extraction is demonstrated to be an alternative, efficient method for the vegetable oil production.

  16. [Inhibition of Linseed Oil Autooxidation by Essential Oils and Extracts from Spice Plants].

    Science.gov (United States)

    Misharina, T A; Alinkina, E S; Terenina, M B; Krikunova, N I; Kiseleva, V I; Medvedeva, I B; Semenova, M G

    2015-01-01

    Clove bud essential oil, extracts from ginger, pimento and black pepper, or ascorbyl palmytate were studied as natural antioxidants for the inhibition of autooxidation of polyunsaturated fatty acids in linseed oil. Different methods were used to estimate antioxidant efficiency. These methods are based on the following parameters: peroxide values; peroxide concentration; content of degradation products of unsaturated fatty acid peroxides, which acted with thiobarbituric acid; diene conjugate content; the content of volatile compounds that formed as products of unsaturated fatty acid peroxide degradation; and the composition of methyl esters of fatty acids in samples of oxidized linseed oil.

  17. In Vitro Antibacterial Effects of Five Volatile Oil Extracts Against Intramacrophage Brucella Abortus 544

    Directory of Open Access Journals (Sweden)

    Ayman Al-Mariri

    2012-06-01

    Full Text Available Background: Brucella abortus is a gram-negative facultative intracellular bacterium that can cause a highly contagious disease in sheep, goats, cattle and one-humped camels. It is responsible for one of the most important zoonosis in human. The aim of this study was to evaluate the role of Mentha piperita, Origanum majorana, Citrus lemon, Cinnamomum verum and Myristica fragrans essential volatile oil extracts on human macrophages infected by B. abortus 544. Methods: Essential volatile oil extracts from M. piperita, O. majorana, C. lemon, C. verum and M. fragrans were extracted. Human macrophages were cultured at a density of 2×105 cells per well in sterile 96-well microtiter plates, and infected with B. abortus 544 at a ratio of 1:100 bacteria/cell. Then essential volatile oil extracts were added at a concentration of 1%. At specified times; cells were washed, lysed with 0.1% Triton, and plated on 2YT agar to determine the number of intracellular bacteria. Results: Cinnamomum verum volatile oil at a concentration of 1% had the highest antibacterial activity against B. abortus 544 inside human macrophages. Its inhibitory effect observed from 24 h and continued till 144 h after the infection. Moreover, C. verum (0.1% in combination with 1% concentration of M. piperita, O. majorana, C. lemon or M. fragrans volatile oil extracts produced a synergistic inhibitory effect against B. abortus 544. Conclusion: The results indicate that, among the five selected oil extracts, C. verum volatile oil applied either separately or in combination with other oil extracts had the most effective antimicrobial activity against Brucella.

  18. Chemical Composition and Antioxidant Activity of Essential Oil and Organic Extracts of Premna integrifolia Linn

    Directory of Open Access Journals (Sweden)

    Sharif M. Al-Reza

    Full Text Available ABSTRACT This study was designed to examine the chemical composition and in vitro antioxidant activity of the hydrodistillated essential oil and various extracts obtained from Premna integrifolia Linn. GC-MS analysis of the essential oil was resulted in determination 29 different compounds, representing 95.73% of total oil. Antioxidant activities of the essential oil and organic extracts of chloroform, ethyl acetate and methanol were determined by three different test systems namely DPPH (2,2-diphenyl-1-picrylhydrazyl, superoxide and nitric oxide radical scavenging assays. The essential oil and methanol extract showed potent antioxidant activity among all the tested samples. Furthermore, the amount of total phenolic compounds was determined and its content in methanol extract was the highest as compared to other samples. The results indicate that the essential oil and extracts of Premna integrifolia could serve as an important bio-resource of antioxidants for using in the pharmaceutical industries.

  19. Evaluation of anxiolytic and sedative effect of essential oil and hydroalcoholic extract of Ocimum basilicum L. and chemical composition of its essential oil.

    Science.gov (United States)

    Rabbani, Mohammed; Sajjadi, Seyed Ebrahim; Vaezi, Arefeh

    2015-01-01

    Ocimum basilicum belongs to Lamiaceae family and has been used for the treatment of wide range of diseases in traditional medicine in Iranian folk medicine. Due to the progressive need to anti-anxiety medications and because of the similarity between O. basilicum and Salvia officinalis, which has anti-anxiety effects, we decided to investigate the anxiolytic and sedative activity of hydroalcoholic extract and essential oil of O. basilicum in mice by utilizing an elevated plus maze and locomotor activity meter. The chemical composition of the plant essential oil was also determined. The essential oil and hydroalcoholic extract of this plant were administered intraperitoneally to male Syrian mice at various doses (100, 150 and 200 mg/kg of hydroalcoholic extract and 200 mg/kg of essential oil) 30 min before starting the experiment. The amount of hydroalcoholic extract was 18.6% w/w and the essential oil was 0.34% v/w. The major components of the essential oil were methyl chavicol (42.8%), geranial (13.0%), neral (12.2%) and β-caryophyllene (7.2%). HE at 150 and 200 mg/kg and EO at 200 mg/kg significantly increased the time passed in open arms in comparison to control group. This finding was not significant for the dose of 100 mg/kg of the extract. None of the dosages had significant effect on the number of entrance to the open arms. Moreover, both the hydroalcoholic extract and the essential oil decreased the locomotion of mice in comparison to the control group. This study shows the anxiolytic and sedative effect of hydroalcoholic extract and essential oil of O. basilicum. The anti-anxiety and sedative effect of essential oil was higher than the hydroalcoholic extract with the same doses. These effects could be due to the phenol components of O. basilicum.

  20. Application of forward osmosis membrane technology for oil sands process-affected water desalination.

    Science.gov (United States)

    Jiang, Yaxin; Liang, Jiaming; Liu, Yang

    2016-01-01

    The extraction process used to obtain bitumen from the oil sands produces large volumes of oil sands process-affected water (OSPW). As a newly emerging desalination technology, forward osmosis (FO) has shown great promise in saving electrical power requirements, increasing water recovery, and minimizing brine discharge. With the support of this funding, a FO system was constructed using a cellulose triacetate FO membrane to test the feasibility of OSPW desalination and contaminant removal. The FO systems were optimized using different types and concentrations of draw solution. The FO system using 4 M NH4HCO3 as a draw solution achieved 85% water recovery from OSPW, and 80 to 100% contaminant rejection for most metals and ions. A water backwash cleaning method was applied to clean the fouled membrane, and the cleaned membrane achieved 77% water recovery, a performance comparable to that of new FO membranes. This suggests that the membrane fouling was reversible. The FO system developed in this project provides a novel and energy efficient strategy to remediate the tailings waters generated by oil sands bitumen extraction and processing.

  1. The Effect of Homogenization Pressures on Extraction of Avocado Oil by Wet Method

    OpenAIRE

    Basuni Hamzah

    2013-01-01

    Avocado tree usually planted by people of Indonesia in rural are small in scale. Mostly, in the modern and high scale industry especially company has a large avocado farm the extraction of avocado oil is extracted through vacuum drying in low temperature. However, in rural area avocado tree spread out in small number of tree, so it needs alternative method of avocado oil extraction. In this experiment, wet method of avocado extraction was applied similar to traditional extraction of coconut o...

  2. Larvicidal effects of mineral turpentine, low aromatic white spirits, aqueous extracts of Cassia alata, and aqueous extracts, ethanolic extracts and essential oil of betel leaf (Piper betle) on Chrysomya megacephala.

    Science.gov (United States)

    Kumarasinghe, Sujith Prasad W; Karunaweera, Nadira D; Ihalamulla, Ranjan L; Arambewela, Lakshmi S R; Dissanayake, Roshinie D S C T

    2002-12-01

    Many methods have been employed, with variable success, in the treatment of cutaneous myiasis caused by Chrysomya species. Experiment 1: to assess the larvicidal effect of mineral turpentine (MT) and the main ingredient of MT, low aromatic white spirits (LAWS), on Chrysomya megacephala larvae in vitro. Experiment 2: to assess the larvicidal effects of aqueous extracts of winged senna (Cassia alata), and aqueous extracts, ethanolic extracts and essential oil of betel leaf (Piper betle). In experiment 1, two samples of LAWS were obtained from two industrialists (samples 1 and 2). Adult flies of C. megacephala were bred in the insectory of the Department of Parasitology, Faculty of Medicine, University of Colombo. Petri dishes were prepared with pads of cotton wool. These cotton pads were soaked separately in MT, LAWS samples 1 and 2, and normal saline as a control. Ten larvae were placed in each Petri dish. The activity of the larvae was observed and recorded half-hourly. MT and the two samples of LAWS were analyzed by chromatography. In experiment 2, volatile essential oil of betel was prepared using a standard steam distillation process. An ethanolic extract of betel was obtained after boiling the crushed leaf with water, and mixing the stock with ethanol. Betel oil dilutions of 1-4% were prepared using 1% Tween 80 (v/v aq) as a solvent, with 0.05 g/100 mL sodium lauryl sulphate (as stabilizer) and 0.01 g/100 mL methyl paraben (as a preservative). Cotton wool swabs soaked in 1, 2, 3 and 4% essential oil of betel in 1% Tween 80 (v/v aq) prepared as above, 1, 2, 3 and 4% ethanolic extract of betel, 50 and 25% aqueous extract of C. alata, and 50 and 25% aqueous extract of betel were placed in separate Petri dishes. Ten larvae were placed in each Petri dish. 1% Tween 80 solvent with the stabilizer and the preservative, but without betel essential oil, was used as a negative control and MT was used as a positive control. Larval motility was assessed as before. MT and

  3. EXTRACTION AND CHARACTERIZATION OF FATTY ACIDS IN CARNAÚBA SEED OIL

    Directory of Open Access Journals (Sweden)

    WELLINSON GADÊLHA GUIMARÃES

    2014-01-01

    Full Text Available This paper describes the composition of fatty acids in oil extracted from seeds of carnaúba ( Copernicia prunifera (Miller H. E. Moore, an important palm species native to Northeastern Brazil. After extracting the crude oil, the physico - chemical characteristics (density, refraction index, pH, acidity and saponi- fication index were registered and the chemical composition of the fatty acids was determined by gas chroma- tography (GC - FID. The predominance of saturated fatty acids does not make carnaúba seed oil a promising alternative for the food industry, and the small yield obtained (approx. 5% may constitute a limiting factor for commercial exploitation, but carnauba seed oil could potentially be used in the production of biofuels, cosmet- ics and detergents.

  4. APPLICATION OF ESSENTIAL OILS EXTRACTED FROM PEELS OF ORANGES AS A PARTIAL SUBSTITUTE OF FLOCCULANT

    Directory of Open Access Journals (Sweden)

    Anna Kowalczyk

    2016-05-01

    Full Text Available The study attempts to determine the optimum conditions of the process of mechanical dewatering of municipal sewage sludge and reduction of odours emitted during this process. The process of dewatering of municipal sewage sludge was carried out using laboratory sedimentation centrifuge of MPW-350 type. Municipal sewage sludge stabilized during anaerobic digestion, taken from Wastewater Treatment Plant Jamno. The dewatering process was aided by cationic flocculant Praestol 855BS of real solution concentration 0.3% and essential oil from orange, which was extracted from orange peels in the process of steam distillation. Constant parameters of dewatering process were: pH, temperature, colour, texture, smell, water content and dry matter content. Independent variables of dewatering process were: centrifugation time (in the range 1–10 min, centrifugation speed (in the range 1000–3000 rotations/min and dose of mixture of flocculant Praestol 855BS (79% + essential oil of orange (21% in the range 0–48 ml/dm3. Water content in the sludge after the process, dry matter content in the effluent and the duration of the smell of oil in the sediment were determined. Studies showed that the essential oil from orange may be used as a partial substitute of flocculant Praestol 855BS in the process of centrifugal sedimentation. Essential oil of orange significantly reduces unpleasant odours which are emitted from sludge during mechanical dewatering. Simultaneous application of both reagents, ie. flocculant Praestol 855BS 79%, and essential oil of orange 21% of volume is recommended.

  5. Antioxidant activity of oils extracted from orange (Citrus sinensis seeds

    Directory of Open Access Journals (Sweden)

    Neuza Jorge

    2016-06-01

    Full Text Available Due to the increasing production of food in the world with consequent increase of the production of waste, the importance of developing researches for its use is noticed. Thus, the interest in vegetable oils with bioactive compounds, such as the ones extracted from fruit seeds, is growing. Therefore, the present study aims to characterize the oils extracted from seeds of Hamlin, Natal, Pera-rio and Valencia orange varieties (Citrus sinensis, as to the levels of total carotenoids, total phenolic compounds, tocopherols and phytosterols, as well as to determine their antioxidant activity. The orange seed oils presented important content of total carotenoids (19.01 mg/kg, total phenolic compounds (4.43 g/kg, α-tocopherol (135.65 mg/kg and phytosterols (1304.2 mg/kg. The antioxidant activity ranged from 56.0% (Natal to 70.2% (Pera-rio. According to the results it is possible to conclude that the orange seed oils can be used as specialty oils in diet, since they contain considerable amounts of bioactive compounds and antioxidants.

  6. Supercritical extraction of carqueja essential oil: experiments and modeling

    Directory of Open Access Journals (Sweden)

    R. M. F. Vargas

    2006-09-01

    Full Text Available Baccharis trimera is a native Brazilian plant which has medicinal properties. In this work a method of supercritical extraction was studied to obtain the popularly essential oil from Baccharis trimera, known as carqueja. The aim was to obtain experimental data and to compare two mathematical models used in the simulation of carqueja (Baccharis trimera oil extraction by supercritical CO2. The two mathematical models are based on mass transfer. One of the models, proposed by Reverchon, is solved numerically and requires two adjustable parameters from the experimental data. The other model chosen is the one proposed by Sovová. This model is solved analytically and requires four adjustable parameters. Numerical results are presented and discussed for the adjusted parameters. The experimental results are obtained in a temperature range of 313.15 K to 343.15 K at 90 bar. The extraction yield of carqueja essential oil using supercritical carbon dioxide ranged between 1.72 % (w/w at 323.15 K and 2.34 % (w/w at 343.15 K, 90 bar with a CO2 flow rate of 3.34.10-8 m³/s for a 0.0015 kg sample of Baccharis trimera.

  7. MODELING OF SUPERCRITICAL FLUID EXTRACTION KINETIC OF FLAXSEED OIL BY DIFFUSION CONTROL METHOD

    Directory of Open Access Journals (Sweden)

    Emir Zafer HOŞGÜN

    2013-06-01

    Full Text Available In this study, Flaxseed oil was extracted by Supercritical Carbondioxide Extraction, and extractionkinetics was modelled using diffusion controlled method.The effect of process parameters, such as pressure (20, 35, 55 MPa, temperature (323 and 343 K, and CO2 flow rate (1 and 3 L CO2 /min on the extraction yield and effective diffusivity (De was investigated. The effective diffusion coefficient varied between 2.4 x10-12 and 10.8 x10-12 m2s-1 for the entire range of experiments and increased with the pressure and flow rate. The model fitted well theexperimental data (ADD varied between 2.35 and 7.48%.

  8. Influence of green solvent extraction on carotenoid yield from shrimp (Pandalus borealis) processing waste

    DEFF Research Database (Denmark)

    Razi Parjikolaei, Behnaz; El-Houri, Rime Bahij; Fretté, Xavier

    2015-01-01

    In this work, sunflower oil (SF) and methyl ester of sunflower oil (ME-SF) were introduced as two green solvents for extracting astaxanthin (ASX) from shrimp processing waste. The effects of temperature (25, 45, 70 °C), solvent to waste ratio (3, 6, 9), waste particle size (0.6 and 2.5 mm...

  9. A review on green trend for oil extraction using subcritical water technology and biodiesel production.

    Science.gov (United States)

    Abdelmoez, Weal; Ashour, Eman; Naguib, Shahenaz M

    2015-01-01

    It became a global agenda to develop clean alternative fuels which were domestically available, environmentally acceptable and technically feasible. Thus, biodiesel was destined to make a substantial contribution to the future energy demands of the domestic and industrial economies. Utilization of the non edible vegetable oils as raw materials for biodiesel production had been handled frequently for the past few years. The oil content of these seeds could be extracted by different oil extraction methods, such as mechanical extraction, solvent extraction and by subcritical water extraction technology SWT. Among them, SWT represents a new promising green extraction method. Therefore this review covered the current used non edible oil seeds for biodiesel production as well as giving a sharp focus on the efficiency of using the SWT as a promising extraction method. In addition the advantages and the disadvantages of the different biodiesel production techniques would be covered.

  10. Comparative analysis of the oil and supercritical CO(2) extract of Artemisia arborescens L. and Helichrysum splendidum (Thunb.) Less.

    Science.gov (United States)

    Marongiu, Bruno; Piras, Alessandra; Porcedda, Silvia

    2006-05-10

    Isolation of volatile concentrate from the dried leaves of Artemisia arborescens and of Helichrysum splendidum has been obtained by supercritical extraction with carbon dioxide. To obtain a pure volatile extract devoid of cuticular waxes, the extraction products were fractionated in two separators operating in series. A good extraction process was obtained operating at 90 bar and 50 degrees C in the extraction vessel, at 90 bar and at -5 degrees C in the first separator and at a pressure between 20 and 15 bar and temperatures in the range 10-20 degrees C in the second one. The composition of the volatile concentrate has been analyzed by GC/MS. The volatile concentrate of A. arborescens was found to contain: trans-thujone (13.96%), camphor (6.15%) and chamazulene (5.95%). The main constituents in the extract of H. splendidum were: germacrene D-4-ol (17.08%), germacrene D (9.04%), bicyclogermacrene (8.79%) and delta-cadinene (8.43%). A comparison with the oils obtained by hydrodistillation is also given. The differences observed between the composition of the SFE volatile concentrates and of the hydrodistilled (HD) oils were relevant. Indeed, the HD oils had a blue color whereas the volatile concentrates were pale yellow. The HD oil of H. splendidum had a blue color due to the presence of guaiazulene (0.42% vs 0%), whereas the coloration of HD oil of A. arborecens was due to the high concentration of chamazulene (26.64% vs 3.37%).

  11. Multiclass mycotoxin analysis in edible oils using a simple solvent extraction method and liquid chromatography with tandem mass spectrometry.

    Science.gov (United States)

    Eom, Taeyong; Cho, Hyun-Deok; Kim, Junghyun; Park, Mihee; An, Jinyoung; Kim, Moosung; Kim, Sheen-Hee; Han, Sang Beom

    2017-11-01

    A simple and rapid method for the simultaneous determination of 11 mycotoxins - aflatoxins B 1 , B 2 , G 1 and G 2 ; fumonisins B 1 , B 2 and B 3 ; ochratoxin A; zearalenone; deoxynivalenol; and T-2 toxin - in edible oils was established using liquid chromatography tandem mass spectrometry (LC-MS/MS). In this study, QuEChERS (Quick, Easy, Cheap, Effective, Rugged and Safe), QuEChERS with dispersive liquid-liquid microextraction, and solvent extraction were examined for sample preparation. Among these methods, solvent extraction with a mixture of formic acid/acetonitrile (5/95, v/v) successfully extracted all target mycotoxins. Subsequently, a defatting process using n-hexane was employed to remove the fats present in the edible oil samples. Mass spectrometry was carried out using electrospray ionisation in polarity switching mode with multiple reaction monitoring. The developed LC-MS/MS method was validated by assessing the specificity, linearity, recovery, limit of quantification (LOQ), accuracy and precision with reference to Commission Regulation (EC) 401/2006. Mycotoxin recoveries of 51.6-82.8% were achieved in addition to LOQs ranging from 0.025 ng/g to 1 ng/g. The edible oils proved to be relatively uncomplicated matrices and the developed method was applied to 9 edible oil samples, including soybean oil, corn oil and rice bran oil, to evaluate potential mycotoxin contamination. The levels of detection were significantly lower than the international regulatory standards. Therefore, we expect that our developed method, based on simple, two-step sample preparation process, will be suitable for the large-scale screening of mycotoxin contamination in edible oils.

  12. Antimicrobial activity and chemical constituents of essential oils and oleoresins extracted from eight pepper species

    Directory of Open Access Journals (Sweden)

    Laira Martinelli

    Full Text Available ABSTRACT: Essential oils are the most important compounds produced during secondary metabolism in aromatic plants. Essential oils are volatile, have characteristic odor and are used as defensive agents by plants. In pepper, it is possible to say that essential oils are the “flavor fingerprint” of each species. In the present article, eight species of pepper were studied in order to extract their essential oils and oleoresins, test their antibacterial and antifungal activities and also to identify the compounds present in the most bioactive samples. Results demonstrated that two essential oils [Pimenta dioica (L. Merr. and Schinus terebinthifolius] and three oleoresins (Schinus terebinthifolius and Piper nigrum white and black recorded significant antimicrobial activity. These active essential oils and oleoresins are interesting for use in biotechnological processes employed in food, pharmaceutical and other industries.

  13. Estimation of Dermatological Application of Creams with St. John’s Wort Oil Extracts

    Directory of Open Access Journals (Sweden)

    Dušanka Runjaić-Antić

    2011-12-01

    Full Text Available Oleum Hyperici, the oil extract of St. John’s Wort (SJW, is one of the oldest folk remedies, traditionally used in the topical treatment of wounds, bruises, ulcers, cuts, burns, hemorrhoids and also as an antiseptic. Considering the advantageous characteristics of emulsion applications, in the present study we have formulated three O/W creams containing 15% (w/v of SJW oil extract as an active ingredient. The aim was to estimate dermatological application of the prepared creams for the abovementioned indications. The extracts were prepared according to the prescriptions from traditional medicine, however with different vegetable oils used as an extractant, namely: Olive, palm and sunflower oil. The investigated O/W creams demonstrated significant antiinflammatory effects in an in vivo double-blind randomized study, using a sodium lauryl sulphate test. Both skin parameters assessed in the study (electrical capacitance and erythema index, were restored to the baseline value after a seven-day treatment with the tested creams. Almost all investigated SJW oil extracts and corresponding creams displayed the same antimicrobial activity against the most of the investigated microorganisms with obtained minimal inhibitory concentrations values of 1,280 µg/mL, 2,560 µg/mL or >2,560 µg/mL.

  14. Comparison of the generation of oil by the extraction and the hydropyrolysis of biomass

    Energy Technology Data Exchange (ETDEWEB)

    O. Onay; A.F. Gaines; O.M. Kockar; M. Adams; T.R. Tyagi; C.E. Snape [Anadolu University, Eskisehir (Turkey). Department of Chemical Engineering, Faculty of Engineering

    2006-02-01

    This paper discusses the maximisation of the yields of useful bio-oils generated from seeds and nut-shells both by extraction and by hydropyrolysis. The formation and the composition of the bio-oils are also discussed. Powdered (<0.25 mm diameter) Rapeseed, Linseed and Safflower seed and Hazel nut and Walnut shells, that is, fresh precursors of liptinite, have been characterised by their elemental analyses, infra-red and NMR spectra. Bio-oils obtained both by extraction and by slow hydropyrolysis to 520{sup o}C at moderate pressure in the presence of ammonium dioxydithiomolybdate have been compared by the same analyses and by gas chromatography. Consistent with previous work (Hardy JA. A greener future with biodiesel. Green Chem 2001 G56-G57), extraction of the seeds with organic solvents, including Diesel oil, gave yields of up to 40% together with an uninteresting residue. However, subsequent saponification of the residues gave further yields of oil. Hydropyrolysis removed oxygen from the seeds as water and as oxides of carbon to generate bio-oil in yields of up to 75%. Whereas little oil could be extracted from the nut-shells, hydropyrolysis gave oil yields of {approximately} 40%. Some char was also formed, suggesting that optimisation of the hydropyrolysis might give even larger yields of oil. 25 refs., 4 figs., 10 tabs.

  15. Effect of extraction methods on the stability of benniseed oil from ...

    African Journals Online (AJOL)

    , 3.06mg KOH/g and 6.02mg KOH/g for the oil expeller, mechanical press and solvent freshly extracted oil samples respectively. The corresponding peroxide values were 1.47mg eq/g, 2.14mg eq/g and 2.89mg eq/g. The FFA for the oils after 4 ...

  16. Effect of oil refining processes on 14 C-tetrachlorvinphos residues in soya bean oil

    International Nuclear Information System (INIS)

    Farghaly, M.; Zayed, S.M.A.D.

    1986-01-01

    Crude soya bean oil extracted from grains treated with 14 C-tetrachlorvinphos and stored for 30 weeks was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleaching, winterization and deodorization on the nature and magnitude of the originally present residues was investigated. A high percentage (52%) of the residues was eliminated during alkali neutralization. No potentially toxic materials were detected among the identified degradation products. The obtained data showed that the ultimate degradation products were dimethyl phosphate and mono methyl phosphate.2 tab.,2 scheme

  17. EXTRACTION OF OIL FROM PRESSED PALM OIL (Elaes guineensis FIBERS USING SUPERCRITICAL CO2

    Directory of Open Access Journals (Sweden)

    Luiz F. FRANÇA

    1997-12-01

    Full Text Available Residual fibers from palm oil production are a good source of carotene, since they contain more than 5% of the original oil, with about 5000 ppm of carotenoids. As carotenoids are thermosensitive molecules, supercritical CO2 can be used for oil recovery, because this technique employs low temperatures. In this work results of oil extraction experiments from pressed palm oil fibers are shown. Fibers were from AGROPALMA, an industry which is located in Tailândia (Pará, Brazil. Extractions were carried out at 200, 250 and 300 bar and at temperatures of 45 and 55oC. Oil was analyzed by UV/vis spectrophotometry for total carotene determination. Results showed a large increase in extraction rate from 200 to 250 bar and a small variation from 250 to 300 bar. The total amount of carotenes did not increase in the course of extraction at 300 bar, but it showed a large increase at 200 and at 250 bar. Free fatty acids are present in amounts larger than those found in commercial oils.As fibras residuais do processo de produção de óleo de palma (óleo de dendê, podem ser uma boa fonte de carotenos, pois contém, ainda, mais de 5% do óleo original, com cerca de 5.000 ppm de carotenóides. Como os carotenóides são moléculas termodegradáveis, é importante um estudo do emprego de CO2 supercrítico na extração deste óleo, visto que esta é uma técnica que emprega baixas temperaturas. Neste trabalho são mostrados os resultados de experimentos de extração do óleo das fibras prensadas de dendê, feitas a 200, 250 e 300 bar e temperaturas de 45 e 55oC. As fibras prensadas foram obtidas da produção industrial da indústria AGROPALMA, localizada em Tailândia (Pará, Brasil. O óleo obtido foi analisado por espectrofotometria UV/vis para a determinação do teor de carotenos totais. Os resultados mostram um aumento na taxa de extração entre 200 e 250 bar, mas esta variação foi pequena entre 250 e 300 bar. O teor de carotenos totais não aumenta

  18. Essential Oil Extraction, Chemical Analysis and Anti-Candida Activity of Calamintha nepeta (L. Savi subsp. glandulosa (Req. Ball—New Approaches

    Directory of Open Access Journals (Sweden)

    Mijat Božović

    2017-01-01

    Full Text Available A comprehensive study on essential oils extracted from different Calamintha nepeta (L. Savi subsp. glandulosa (Req. Ball samples from Tarquinia (Italy is reported. In this study, the 24-h steam distillation procedure for essential oil preparation, in terms of different harvesting and extraction times, was applied. The Gas chromatography–mass spectrometry (GC/MS analysis showed that C. nepeta (L. Savi subsp. glandulosa (Req. Ball essential oils from Tarquinia belong to the pulegone-rich chemotype. The analysis of 44 samples revealed that along with pulegone, some other chemicals may participate in exerting the related antifungal activity. The results indicated that for higher activity, the essential oils should be produced with at least a 6-h steam distillation process. Even though it is not so dependent on the period of harvesting, it could be recommended not to harvest the plant in the fruiting stage, since no significant antifungal effect was shown. The maximum essential oil yield was obtained in August, with the highest pulegone percentage. To obtain the oil with a higher content of menthone, September and October should be considered as the optimal periods. Regarding the extraction duration, vegetative stage material gives the oil in the first 3 h, while material from the reproductive phase should be extracted at least at 6 or even 12 h.

  19. Antifouling potential of seaweed, sponge and cashew nut oil extracts ...

    African Journals Online (AJOL)

    SAM

    2014-07-02

    Jul 2, 2014 ... nut oil extracts against biofilm bacteria and green mussel Perna ... prevent photo and thermal degradation during the transport to the laboratory. ... 40°C. The resultant extractives were collected in air-tight plastic vials and ...

  20. Supercritical Carbon Dioxide Extraction of Seed Oil from Winter Melon (Benincasa hispida and Its Antioxidant Activity and Fatty Acid Composition

    Directory of Open Access Journals (Sweden)

    Ali Ganjloo

    2013-01-01

    Full Text Available In the present study, supercritical carbon dioxide (SC-CO2 extraction of seed oil from winter melon (Benincasa hispida was investigated. The effects of process variables namely pressure (150–300 bar, temperature (40–50 °C and dynamic extraction time (60–120 min on crude extraction yield (CEY were studied through response surface methodology (RSM. The SC-CO2 extraction process was modified using ethanol (99.9% as co-solvent. Perturbation plot revealed the significant effect of all process variables on the CEY. A central composite design (CCD was used to optimize the process conditions to achieve maximum CEY. The optimum conditions were 244 bar pressure, 46 °C temperature and 97 min dynamic extraction time. Under these optimal conditions, the CEY was predicted to be 176.30 mg-extract/g-dried sample. The validation experiment results agreed with the predicted value. The antioxidant activity and fatty acid composition of crude oil obtained under optimized conditions were determined and compared with published results using Soxhlet extraction (SE and ultrasound assisted extraction (UAE. It was found that the antioxidant activity of the extract obtained by SC-CO2 extraction was strongly higher than those obtained by SE and UAE. Identification of fatty acid composition using gas chromatography (GC showed that all the extracts were rich in unsaturated fatty acids with the most being linoleic acid. In contrast, the amount of saturated fatty acids extracted by SE was higher than that extracted under optimized SC-CO2 extraction conditions.

  1. Antimicrobial activity of the essential oil and extracts of Cordia curassavica (Boraginaceae).

    Science.gov (United States)

    Hernandez, Tzasna; Canales, Margarita; Teran, Barbara; Avila, Olivia; Duran, Angel; Garcia, Ana Maria; Hernandez, Hector; Angeles-Lopez, Omar; Fernandez-Araiza, Mario; Avila, Guillermo

    2007-04-20

    In traditional Mexican medicine Cordia curassavica (Jacq) Roemer & Schultes is used to treat gastrointestinal, respiratory and dermatological disorders in Zapotitlán de las Salinas, Puebla (México). The aim of this work was to investigate antimicrobial activity of the essential oil, obtained by using Clevenger distillation apparatus, and hexane, chloroform and methanol extracts from aerial parts of Cordia curassavica. Antimicrobial activity was evaluated against 13 bacteria and five fungal strains. The oil and extracts exhibited antimicrobial activity against Gram-positive and Gram-negative bacteria and five fungal strains. Sarcina lutea and Vibrio cholerae were the strains more sensitive to the essential oil effect (MIC=62 microg/mL) and Vibrio cholerae for the hexane extract (MIC=125 microg/mL). Rhyzoctonia solani was the strain more sensitive to the essential oil effect (IC(50)=180 microg/mL) and Trichophyton mentagrophytes for the hexane extract (IC(50)=230 microg/mL). The essential oil was examined by GC and GC-MS. A total 11 constituents representing 96.28% of the essential oil were identified: 4-methyl,4-ethenyl-3-(1-methyl ethenyl)-1-(1-methyl methanol)cyclohexane (37.34%), beta-eudesmol (19.21%), spathulenol (11.25%) and cadina 4(5), 10(14) diene (7.93%) were found to be the major components. The present study tends to confirm the use in the folk medicine of Cordia curassavica in gastrointestinal, respiratory and dermatological diseases.

  2. Phenolic Extracts from Wild Olive Leaves and Their Potential as Edible Oils Antioxidants

    Directory of Open Access Journals (Sweden)

    Theodora-Ioanna Lafka

    2013-01-01

    Full Text Available The kinetics solid-liquid extraction of phenolics from wild olive leaves was elaborated using different mathematical models (Peleg, second order, Elovich, and power law model. As solvents, methanol, ethanol, ethanol:water 1:1, n-propanol, isopropanol and ethyl acetate were used. The second order model best described the solvent extraction process, followed by the Elovich model. The most effective solvent was ethanol with optimum phenol extraction conditions 180 min, solvent to sample ratio 5:1 v/w and pH 2. Ethanol extract exhibited the highest antiradical activity among solvent and supercritical fluid extraction (SFE extracts, which in addition showed the highest antioxidant capacity compared to synthetic and natural food antioxidants such as BHT, ascorbyl palmitate and vitamin E. Antioxidant potential of SFE extract was quite high, although its phenolic potential was not. Leaf extracts were proven to be good protectors for olive and sunflower oils at levels of 150 ppm.

  3. Evaluation Study Of Inhibition And Regeneration Characters For Substituted Anilines Extracted From Crude Oil

    Directory of Open Access Journals (Sweden)

    Dr. Mohammad Jamil Abd-Alghani

    2015-08-01

    Full Text Available Abstract Aniline derivatives containing carbonyl group in the side chain was extracted from crude oil received from Al- Dora refinery. The crude oil was dissolved in xylene 13 and extracted through a column containing activated cationic resin type Amberlyte 15 then eluted by absolute ethanol and identified by infra red spectroscopy then examined as antioxidant for lubricant oil stock 50. FT-IR spectroscopy for the lubricant oil was performed before employing in an internal combustion engine and 190 hrs after. It was seen that the FT-IR of the oxidized oil contains a new peak in the region 1700 1800 cm1 which is formed due to the oxidation of base oil which belongs to carbonyl group. The FT-IR specter for the formulated crude oil with a specific concentration of the extracted substituted aniline after applying the same conditions of oxidation 190 working hrs. in an internal combustion engine showed a minimum peak intensity at 1710 1770 cm-1 than that observed in FT-IR done in absence of extracted antioxidant. The values of induction periods in presence of 0.20 and 0.30 moll of the extracted sample in the lubricant oil at 393 K were 766 sec. 1630 sec. while in their absence was 55 sec.. The values of maximum rates of oxidation were 3.0x10-4 and 2.0x10-4 moll. sec. These values were still not arrived the value of maximum rate of oxidation for the lubricant oil 3.5 x10-4 mol.l.sec. The same study was applied on the universal antioxidant inhibitor 2 6-diter-butyl-4-methyl phenol phenolic type under the same conditions. The obtained induction periods were 150 290 sec. respectively. This means that the values of induction periods obtained by formulating the lubricant oil with the extracted aniline molecule were 7 times greater than do the 2 6- diter-butyl-4-methyl phenol molecule. From the literatures it is known that the value of stochiometric factor for inhibition f for 2 4 6-triisobutyl phenol is equal to 2 so as a result the value of stochiometric

  4. An investigation of influence of solvent on the degradation kinetics of carotenoids in oil extracts of Calendula officinalis

    Directory of Open Access Journals (Sweden)

    DEJAN BEZBRADICA

    2005-02-01

    Full Text Available The stability of carotenoids was studied in marigold oil extracts prepared with following solvents: Myritol 312®, paraffin oil, almond oil, olive oil, sunflower oil, grape seed oil, and soybean oil. The concentration of the carotenoids was determined by spectroscopic measurement at 450 nm. Degradation rate showed a first order dependence on the concentration of carotenoids with a faster first stage (which lasted 35–50 days, depending on the solvent and a slower second stage. The highest degradation rates were observed in extracts prepared with linoleic acid rich solvents (sunflower oil, soybean oil and grape seed oil, while the lowest were found in oil with saturated fatty acids (Myritol 312® and paraffin oil. These results confirm the connection between the degradation of carotenoids and lipid autoxidation, and suggest that the influence of the oil solvents on the stability of oil extracts of Calendula officinalis is a factor that must be considered when selecting a solvent for the production of marigold oil extracts.

  5. Hot ethanol extraction: economic feasibility of a new and green process

    Directory of Open Access Journals (Sweden)

    Carré Patrick

    2018-03-01

    Full Text Available A new extraction process using ethanol at a temperature above boiling point is assessed from an economic point of view. The study was based on an assessment of the main operating costs adjusted by Lang’s factor. Operating costs were assessed based on energy consumption calculated using a model of the process developed from experimental results, and for a hypothetical unit with a 160 000 t/year rapeseed crushing capacity. The processing cost was estimated at 47.4 € per ton of processed seed. Amortization represented 35% of this cost, energy 32% and manpower 10%. Uncertainty about investment is the main factor that could lead to significant error in this cost, but this uncertainty could be offset by an adjustment of the amortization duration, most of the equipment being durable. Profit generated by the process relies principally on a better valuation of the meal: higher value comes from higher protein content and quality on the market for GM-free high protein feedstuffs. Oil quality is also improved by a lower oleic acidity, low phospholipid content and pigment concentration. This gain was estimated at 2.5% of the crude oil value. Unlike the conventional hexane process, hot ethanol extraction produces molasses in small proportions. Molasses value was set at 70% of corn price. The process profitability appears sufficiently positive to justify further research to test the hypothesis underlying our model. The main uncertainty lies in the performance of the process in real conditions of counter-flow extraction and solvent regeneration.

  6. Efficacy of plant derived oils and extracts against white-fly, bemisia tabaci (gennadius) on sesame crop

    International Nuclear Information System (INIS)

    Iram, A.; Irfan, M.; Aslam, S.

    2014-01-01

    Whitefly, Bemisia tabaci (Genn.) is a polyphagous pest and is reported on more than 600 host plants worldwide. Different methods are being used for its control. The present experiment was conducted to determine the effect of some plant extracts of mint (Mentha spp.) and gera-nium (Pelargonium graveolens) and soybean oil (Glycine max), mustard oil (Brassica spp.) and taramera oil (Eruca sativa) against whitefly, Bemisia tabaci on sesame crop. The data were recorded 24h before and 24h, 48h, 72h and 168h after application of each spray material. The results showed that whitefly population was significantly suppressed by both the botanical oils and extracts as compared to the control treatment but in general botanical oils showed significant results as compared to plant extracts. Soybean oil was quite effective in reducing whitefly population per leaf, while after second spray soybean oil and extract of Mentha spp. was more effective in the reducing whitefly population per leaf. The results indicated that plant derived oils and extracts have the potential to be used in plant protection strategies but still more research has to be incorporated in the pest management programmes. (author)

  7. Solid carbon dioxide to promote the extraction of extra-virgin olive oil

    Energy Technology Data Exchange (ETDEWEB)

    Zinnai, A.; Venturi, F.; Quartacci, V.F.; Sanmartin, C.; Favati, F.; Andrich, G.

    2016-07-01

    The use of solid carbon dioxide (dry ice) as a cryogen is widespread in the food industry to produce high quality wines, rich in color and perfumes. The direct addition of carbon dioxide to olives in the solid state before milling represents a fundamental step which characterizes this innovative extraction system. At room temperature conditions solid carbon dioxide evolves directly into the air phase (sublimation), and the direct contact between the cryogen and the olives induces a partial solidification of the cellular water inside the fruits. Since the volume occupied by water in the solid state is higher than that in the liquid state, the ice crystals formed are incompatible with the cellular structure and induce the collapse of the cells, besides promoting the diffusion of the cellular substances in the extracted oil, which is thus enriched with cellular metabolites characterized by a high nutraceutical value. Furthermore, a layer of CO2 remains over the olive paste to preserve it from oxidative degradation. The addition of solid carbon dioxide to processed olives induced a statistically significant increase in oil yield and promoted the accumulation of tocopherols in the lipid phase, whereas a not significant increase in the phenolic fraction of the oil occurred. (Author)

  8. Antioxidant capacity of cinnamon extract for palm oil stability.

    Science.gov (United States)

    Shahid, Muhammad Zia; Saima, Hafiza; Yasmin, Adeela; Nadeem, Muhammad Tahir; Imran, Muhammad; Afzaal, Muhammad

    2018-05-16

    Spices and their bioactive components are more promising attractions for their inclusion in diet-based regimes to improve human health. These are sources of natural antioxidants and play an important role in the chemoprevention of diseases and aging. The aim of the current study was to explore the antioxidant potential of cinnamon; a widely used spice throughout the world. The current research was aimed to investigate the antioxidant potential of cinnamon extract. For the purpose, cinnamon sticks were procured from local super market, while palm oil was obtained from local oil industry. The resultant extract was analyzed for its antioxidant activity through total phenolic content (TPC), free radical scavenging activity (DPPH assay), and total antioxidant activity was measured by ferric reducing antioxidant power (FRAP) test. The shelf life of palm oil was checked by adding cinnamon extract in oil at different levels i.e. , 0.05, 0.10, 0.15, 0.20 and 0.25%, to compare the antioxidant potential of the extract whereas, T o acted as control and T BHA @ 0.1% was used as synthetic antioxidant in the oil samples. The oil samples were analyzed for rancidity check during storage (after every seven days for a storage period of four weeks). The results indicated that total phenolic contents (TPC); 1,1-diphenyl-2-picrylhydrazyl (DPPH) and ferric reducing antioxidant power (FRAP) values of cinnamon extract were as 355.01 ± 8.34 gallic acid equivalent per gram (mg GAE/g), 90.18 ± 2.12 (%) and 132.82 ± 3.12 (μmol/g), respectively. The oxidative parameters for treatments i.e., T o , T BHA , T 1 , T 2 , T 3 , T 4 , T 5 were recorded as peroxide value (2.61 ± 0.07, 2.42 ± 0.08, 2.57 ± 0.05, 2.56 ± 0.03, 2.54 ± 0.02, 2.54 ± 0.01, 2.46 ± 0.06 meq/kg, respectively), free fatty acids (0.601 ± 0.05, 0.522 ± 0.02, 0.580 ± 0.07, 0.572 ± 0.03, 0.56 ± 00.07, 0.552 ± 0.03, 0.536 ± 0.05%, respectively), TBA

  9. Improvement of Fermented Fish Flour Quality Using Essential Oil Extracted From Fresh Leaves of Pimenta racemosa (Mill.) J. W. Moore.

    Science.gov (United States)

    Adjou, Euloge S; Dègnon, René G; Dahouenon-Ahoussi, Edwige; Soumanou, Mohamed M; Sohounhloue, Dominique C K

    2017-08-01

    The aim of this study was to evaluate the efficacy of the essential oil extracted from fresh leaves of Pimenta racemosa in the improvement of fermented fish flour producing technology. Essential oil of Pimenta racemosa was extracted by hydrodistillation and its chemical composition was determined by GC and GC/MS. Different types of fermented fish flours from Lesser African Threadfin (Galeoides decadactylus) were produced by the modification of the traditional processing technology and the introduction of a step of essential oil adjunction during the process. Three different essential oil concentrations (0.5, 1.0 and 2.0 μL g -1 ) were investigated. Physicochemical, microbiological and nutritional analyzes were performed in order to evaluate the quality of the fermented fish flour produced. Results obtained revealed that the essential oil of Pimenta racemosa investigated has a chemical composition characterized by the presence of myrcene (25.1%), chavicol (7.5%) and eugenol (51.1%). Fermented fish flour produced have a good nutritional potential. However, on the microbiological level, only samples produced by adjunction of essential oil have a low level of microbial contamination, with an absence of pathogenic microorganisms.

  10. Developing novel one-step processes for obtaining food-grade O/W emulsions from pressurized fluid extracts: processes description, state of the art and perspectives

    OpenAIRE

    SANTOS, Diego Tresinari; MEIRELES, Maria Angela de Almeida

    2015-01-01

    Abstract In this work, a novel on-line process for production of food-grade emulsions containing oily extracts, i.e. oil-in-water (O/W) emulsions, in only one step is presented. This process has been called ESFE, Emulsions from Supercritical Fluid Extraction. With this process, emulsions containing supercritical fluid extracts can be obtained directly from plant materials. The aim in the conception of this process is to propose a new rapid way to obtain emulsions from supercritical fluid extr...

  11. Comparative study of the chemical properties of palm oil extracted ...

    African Journals Online (AJOL)

    The chemical properties of oil samples determined were free fatty acid, acid value, saponification value, peroxide value, iodine value and moisture content. The experimental design adopted was 3 x 2 x 2 factorial randomized complete block design in three replicates. The data of chemical properties of extracted palm oil ...

  12. Extraction process

    International Nuclear Information System (INIS)

    Rendall, J.S.; Cahalan, M.J.

    1979-01-01

    A process is described for extracting at least two desired constituents from a mineral, using a liquid reagent which produces the constituents, or compounds thereof, in separable form and independently extracting those constituents, or compounds. The process is especially valuable for the extraction of phosphoric acid and metal values from acidulated phosphate rock, the slurry being contacted with selective extractants for phosphoric acid and metal (e.g. uranium) values. In an example, uranium values are oxidized to uranyl form and extracted using an ion exchange resin. (U.K.)

  13. The regional economic impact of oil and gas extraction in Texas

    International Nuclear Information System (INIS)

    Lee, Jim

    2015-01-01

    This paper empirically investigates the regional economic impact of oil and gas extraction in Texas during the recent shale oil boom. Regressions with county-level data over the period 2009–2014 support smaller multiplier effects on local employment and income than corresponding estimates drawn from popular input–output-based studies. Economic impacts were larger for extraction from gas wells than oil wells, while the drilling phase generated comparable impacts. Estimates of economic impacts are greater in a dynamic spatial panel model that allows for spillover effects across local economies as well as over time. - Highlights: • Economic impacts and multiplier effects differ between oil and gas wells in Texas. • Interactions among local economies raise employment and income effects. • Impacts persist over time, raising the long-run multipliers. • Greater economic impacts from newly drilled wells than legacy wells.

  14. Extraction of phenolic compounds from extra virgin olive oil by a natural deep eutectic solvent: Data on UV absorption of the extracts

    Directory of Open Access Journals (Sweden)

    Vito Michele Paradiso

    2016-09-01

    Full Text Available This data article refers to the paper “Towards green analysis of virgin olive oil phenolic compounds: extraction by a natural deep eutectic solvent and direct spectrophotometric detection” [1]. A deep eutectic solvent (DES based on lactic acid and glucose was used as green solvent for phenolic compounds. Eight standard phenolic compounds were solubilized in the DES. Then, a set of extra virgin olive oil (EVOO samples (n=65 were submitted to liquid–liquid extraction by the DES. The standard solutions and the extracts were analyzed by UV spectrophotometry. This article reports the spectral data of both the standard solutions and the 65 extracts, as well as the total phenolic content of the corresponding oils, assessed by the Folin–Ciocalteu assay. Keywords: Natural deep eutectic solvents, Extra virgin olive oil, Phenolic compounds, UV spectrophotometry

  15. The effect of a herbal paste and oil extract on the lipid content of canine hair fibres.

    Science.gov (United States)

    Momota, Yutaka; Shimada, Kenichiro; Kadoya, Chihiro; Gin, Azusa; Kobayashi, Jun; Nakamura, Yuka; Matsubara, Takako; Sako, Toshinori

    2017-08-01

    Application of herbal paste and oil to a dog's coat and body before rinsing (often combining with shampooing) is a cosmetic therapy available in Japan. It is highly appreciated by users, who claim that the treatment makes the coat shinier, improves volume and eliminates tangles. However, there has been no scientific evaluation of such treatments. Improvement of hair condition is derived from oils such as sebum and conditioning oils because chemicals are not used. Therefore, we examined nonpolar lipids (the primary lipids in dog hair) and the botanical oils used in this therapy. Hair samples were obtained from six beagle dogs. Groups were based on different combinations of the following processes: rinsing, shampooing, herbal therapy and herbal therapy with oil extract. Analysis of lipids was performed by high performance thin layer chromatography. The processes of shampooing and herbal therapy were associated with an equivalent reduction in cholesterol ester and triglyceride (TG). However, hair treated by herbal therapy combined with oil extract had an almost three-fold higher TG content, even after shampooing. This study demonstrated that the herbal therapy was able to coat hair samples with TG that was not removed with rinsing. Further investigation is required to evaluate the possible benefits of the application of botanical products containing lipids, such as TG, on hair coat quality in dogs. © 2017 The Authors. Veterinary Dermatology published by John Wiley & Sons Ltd on behalf of the ESVD and ACVD.

  16. Valorization of Tomato Processing Waste for Lycopene Extraction

    Directory of Open Access Journals (Sweden)

    Rim Driouich

    2016-11-01

    Full Text Available Lycopene is one of the most powerful antioxidants and singlet oxygen quenching agents. It has been found to be of great medical importance with various anti cancer effects, cardiovascular diseases effective agent and with its ability to be an important carotenoid in preventive medicine. In Tunisia, we note a real consumption of tomato paste. With 28 production units for double and triple concentrated tomato, noting a significant production of waste (approximately 30000 Tonne/year consisting of skins pulp and seeds, which could be an important source of lycopene. Our study is concerned with three solid-phase extraction process: assisted by ultrasonic, by microwave and by homogenizer heating at moderate temperature. Their efficiency for the extraction of lycopene contained in the tomato waste was elaborated. The effect of the main process variables (including solvent polarity, solid-to-liquid ratio, temperature and time on lycopene recovery have been investigated. The yield of the isolated lycopene was determined using UV-Visible spectrophotometry and UPLC-DAD quantification methods. Lycopene-rich extract was obtained from the dried and milled tomatoes waste using ethanol as a food grade extraction solvent and employing microwave assisted extraction process. The optimum conditions were 30 min total extraction time at 50°C temperature and 1bar pressure. The degradation of extracted lycopene through air oxidation and day light effect were also tested. Lycopene is stable when mixed with olive oil as a natural antioxidant. Up to 80% of lycopene degradated when exposed for one month to day light at 25°C.

  17. Hydrodistillation extraction time effect on essential oil yield, composition, and bioactivity of coriander oil.

    Science.gov (United States)

    Zheljazkov, Valtcho D; Astatkie, Tess; Schlegel, Vicki

    2014-01-01

    Coriander (Coriandrum sativum L.) is a major essential oil crop grown throughout the world. Coriander essential oil is extracted from coriander fruits via hydrodistillation, with the industry using 180-240 min of distillation time (DT), but the optimum DT for maximizing essential oil yield, composition of constituents, and antioxidant activities are not known. This research was conducted to determine the effect of DT on coriander oil yield, composition, and bioactivity. The results show that essential oil yield at the shorter DT was low and generally increased with increasing DT with the maximum yields achieved at DT between 40 and 160 min. The concentrations of the low-boiling point essential oil constituents: α-pinene, camphene, β-pinene, myrcene, para-cymene, limonene, and γ-terpinene were higher at shorter DT (essential oil constituent, linalool, was 51% at DT 1.15 min, and increased steadily to 68% with increasing DT. In conclusion, 40 min DT is sufficient to maximize yield of essential oil; and different DT can be used to obtain essential oil with differential composition. Its antioxidant capacity was affected by the DT, with 20 and 240 min DT showing higher antioxidant activity. Comparisons of coriander essential oil composition must consider the length of the DT.

  18. Effect of Artemisia annua L. leaves essential oil and ethanol extract on behavioral assays

    Directory of Open Access Journals (Sweden)

    Fabio F. Perazzo

    Full Text Available Artemisia annua has been used as a traditional plant for the treatment of malaria and fever in China because of the presence of its active compound, artemisinin. The present study evaluated the central activity of the essential oil and the crude ethanol extract of A. annua L. in animals as a part of a psychopharmacological screening of this plant. The extract was prepared in ethanol (AEE and the essential oil (AEO obtained by hydrodistillation, both with fresh leaves. Induced immobility, the forced swimming test (FST and the open-field test (OFT are well-known animal models to study drug-induced depression. The administration of A. annua essential oil or crude ethanol extract increased the immobility time in the FST and decreased other activities (ambulation, exploration, rearing and grooming in the OFT in animals. Both AEO and AEE prolonged pentobarbital-induced sleep as well, but the essential oil had a marked effect. Observing these results, it is possible to suggest that A. annua crude ethanol extract and essential oil could act as depressors on the Central Nervous System (CNS.

  19. RESPONSE SURFACE METHODOLOGY FOR OPTIMIZATION OF THE EXTRACTION OF FLAX (LINUM USITATISSIMUM SEED OIL

    Directory of Open Access Journals (Sweden)

    Tibor Maliar

    2011-12-01

    Full Text Available Flax seed is an important source of ω-3 polyunsaturated fatty acids essential for human physiology. The aim of this paper is to investigate the effects of major parameters of the lipid extraction from flax seed, in relation to the recovery of oil as well as the oil quality properties. The independent variables of extraction were proposed as: organic solvents, temperature, extraction time and solid-liquid ratio. The following quantitative and qualitative parameters were chosen as dependent variables: yield of the lipid fraction, acid value of oil and the absorbance at 490 nm. After calculating the optimal values of the extraction, the validation analysis was carried out and it was found out that the predicted and experimentally verified dependent variables were in agreement with the optimal extraction parameters.doi:10.5219/168

  20. New microwave-integrated Soxhlet extraction. An advantageous tool for the extraction of lipids from food products.

    Science.gov (United States)

    Virot, Matthieu; Tomao, Valérie; Colnagui, Giulio; Visinoni, Franco; Chemat, Farid

    2007-12-07

    A new process of Soxhlet extraction assisted by microwave was designed and developed. The process is performed in four steps, which ensures complete, rapid and accurate extraction of the samples. A second-order central composite design (CCD) has been used to investigate the performance of the new device. The results provided by analysis of variance and Pareto chart, indicated that the extraction time was the most important factor followed by the leaching time. The response surface methodology allowed us to determine optimal conditions for olive oil extraction: 13 min of extraction time, 17 min of leaching time, and 720 W of irradiation power. The proposed process is suitable for lipids determination from food. Microwave-integrated Soxhlet (MIS) extraction has been compared with a conventional technique, Soxhlet extraction, for the extraction of oil from olives (Aglandau, Vaucluse, France). The oils extracted by MIS for 32 min were quantitatively (yield) and qualitatively (fatty acid composition) similar to those obtained by conventional Soxhlet extraction for 8 h. MIS is a green technology and appears as a good alternative for the extraction of fat and oils from food products.

  1. Biodiesel production from wet microalgae feedstock using sequential wet extraction/transesterification and direct transesterification processes.

    Science.gov (United States)

    Chen, Ching-Lung; Huang, Chien-Chang; Ho, Kao-Chia; Hsiao, Ping-Xuan; Wu, Meng-Shan; Chang, Jo-Shu

    2015-10-01

    Although producing biodiesel from microalgae seems promising, there is still a lack of technology for the quick and cost-effective conversion of biodiesel from wet microalgae. This study was aimed to develop a novel microalgal biodiesel producing method, consisting of an open system of microwave disruption, partial dewatering (via combination of methanol treatment and low-speed centrifugation), oil extraction, and transesterification without the pre-removal of the co-solvent, using Chlamydomonas sp. JSC4 with 68.7 wt% water content as the feedstock. Direct transesterification with the disrupted wet microalgae was also conducted. The biomass content of the wet microalgae increased to 56.6 and 60.5 wt%, respectively, after microwave disruption and partial dewatering. About 96.2% oil recovery was achieved under the conditions of: extraction temperature, 45°C; hexane/methanol ratio, 3:1; extraction time, 80 min. Transesterification of the extracted oil reached 97.2% conversion within 15 min at 45°C and 6:1 solvent/methanol ratio with simultaneous Chlorophyll removal during the process. Nearly 100% biodiesel conversion was also obtained while conducting direct transesterification of the disrupted oil-bearing microalgal biomass. Copyright © 2015 Elsevier Ltd. All rights reserved.

  2. Comparative Properties of Amazonian Oils Obtained by Different Extraction Methods

    Directory of Open Access Journals (Sweden)

    Cláudio Galuppo Diniz

    2011-07-01

    Full Text Available Pequi (Caryocar brasiliense Camb., babaçu (Orbignya phalerata Mart., buriti (Mauritia flexuosa, and passion fruit (Passiflora edulis oils were studied to determine their antibacterial, antioxidant and cytotoxic activities, as well as their total phenol and carotenoid contents. The fatty acid contents were determined by GC-MS. The three types of passion fruit oils studied were refined, cold pressed or extracted from seeds in a Soxhlet apparatus. The oils thus obtained showed differences in antioxidant activity and carotenoid content, but were similar in regard to total phenols. Buriti and pequi had the highest carotenoid contents, while refined and cold pressed passion fruit oil displayed the highest antioxidant activity. Pequi oil was the only oil to display antibacterial and cytotoxic activity.

  3. Antioxidant Potential of the Extracts, Fractions and Oils Derived from Oilseeds

    Directory of Open Access Journals (Sweden)

    Shagufta Ishtiaque

    2013-10-01

    Full Text Available The polyphenolic extracts and oils were obtained from ajwain, mustard, fenugreek and poppy seeds. The extracts were partitioned into acidic and neutral polyphenolic fractions and following estimation of total phenolics in the crude extract, acidic and neutral fractions and oil, all were analyzed for their DPPH (2,2-diphenyl-1-picrylhydrazyl scavenging potential, ferric reducing ability and chelating power. The highest amount of polyphenols was found in ajwain (8330 ± 107, then in mustard seeds (2844 ± 56.00 and in fenugreek (1130 ± 29.00, and least in poppy seeds (937 ± 18.52. The higher amounts of polyphenols were estimated in neutral fraction compared to acidic (p fenugreek and least by poppy seed extracts (p < 0.05. The reducing power and the chelating effect of the oilseeds followed the same order as DPPH, but higher % chelation was shown by neutral than acidic fraction (p < 0.05. Though low in polyphenols, the oil fractions were as strong antioxidants as the acidic one. Though oilseeds are used in very small quantity in food, they are potential sources of natural antioxidants and may replace synthetic ones.

  4. Walnut and almond oil screw-press extraction at industrial scale: Effects of process parameters on oil yield and quality; Extracción de aceite de nuez y almendra a escala industrial: efecto de parámetros del proceso sobre el rendimiento y la calidad del aceite

    Energy Technology Data Exchange (ETDEWEB)

    Martínez, M. L.; Bordón, M.G.; Bodoira, R. M.; Penci, M.C.; Ribotta, P.D.; Maestri, D.M.

    2017-07-01

    Walnut and almond kernels are highly nutritious mainly due to their high oil contents. In this study, 32 factorial experimental designs were used to optimize processes for oil extraction by screw-pressing at industrial scale. Experimental designs included seed moisture content (SMC), and restriction die (RD) as the main processing parameters. Theoretical models were scanned against experimental data in order to optimize oil extraction conditions. The response variables analyzed were oil yield (OY), fine solid content (FC) in oil, and oil quality parameters. Fitted models for OY indicated maximum predicted values similar to the highest experimental values. Walnut oil extractions showed a maximum OY (84.5 ± 2.3 %) at 7.21% SMC, and 10 mm RD. For almond kernels, maximum OY (71.9 ± 3.5%) was obtained at 9.42% SMC, and 12 mm RD. Chemical quality parameters from both oils were in the ranges stated in Codex (FAO/WHO) standards for virgin (non-refined) oils. [Spanish] La nuez y almendra son frutos sumamente nutritivos debido a su alto contenido de aceite. Mediante un diseño experimental de tipo factorial 32 se optimizó el proceso de extracción de estos aceites con prensa de tornillo a escala industrial. Las variables de proceso analizadas fueron el contenido de humedad de la semilla (CHS) y el diámetro de reducción (DR). Los modelos ajustados para rendimiento de aceite (RA) indicaron valores máximos predichos similares a los valores experimentales. Las extracciones de aceite de nuez mostraron un RA máximo (84,5 ± 2,3%) a 7,21% CHS, y 10 mm DR. Para almendra, se obtuvo un máximo de RA (71,9 ± 3,5%) con 9,42% de CHS y 12 mm de DR. Los parámetros de calidad química de ambos aceites se encontraban en los rangos establecidos en las normas del Codex (FAO / OMS) para aceites vírgenes (no refinados).

  5. Green solvents and technologies for oil extraction from oilseeds

    OpenAIRE

    Kumar, S. P. Jeevan; Prasad, S. Rajendra; Banerjee, Rintu; Agarwal, Dinesh K.; Kulkarni, Kalyani S.; Ramesh, K. V.

    2017-01-01

    Oilseeds are crucial for the nutritional security of the global population. The conventional technology used for oil extraction from oilseeds is by solvent extraction. In solvent extraction, n-hexane is used as a solvent for its attributes such as simple recovery, non-polar nature, low latent heat of vaporization (330?kJ/kg) and high selectivity to solvents. However, usage of hexane as a solvent has lead to several repercussions such as air pollution, toxicity and harmfulness that prompted to...

  6. Antioxidant and antimicrobial activities of extract and essential oil of ...

    African Journals Online (AJOL)

    STORAGESEVER

    2008-08-04

    Aug 4, 2008 ... The antioxidant potential of extracts and essential oils of korarima (Aframomum corrorima (Braun). P.C.M. Jansen) ... growing interest, both in industry and in scientific research, for ... Due to the complex composition of different plant pro- ducts ..... extracts of Turmeric and ginger (Zingiber officinale). J. Phytol.

  7. Extraction and physico chemical properties of some edible seed oils ...

    African Journals Online (AJOL)

    Six edible seed samples were obtained from Yankura market in Kano metropolis, Kano state. The samples were subjected to extraction for their oil contents. The percentage oil yield from the seeds were 40.60% for Moringa oleifera, 49.39% for cashew, 47.80% for sesame, 11.92% for bitter kola, 38.30% for melon and ...

  8. Chemical Composition of Volatiles; Antimicrobial, Antioxidant and Cholinesterase Inhibitory Activity of Chaerophyllum aromaticum L. (Apiaceae) Essential Oils and Extracts.

    Science.gov (United States)

    Petrović, Goran M; Stamenković, Jelena G; Kostevski, Ivana R; Stojanović, Gordana S; Mitić, Violeta D; Zlatković, Bojan K

    2017-05-01

    The present study reports the chemical composition of the headspace volatiles (HS) and essential oils obtained from fresh Chaerophyllum aromaticum root and aerial parts in full vegetative phase, as well as biological activities of their essential oils and MeOH extracts. In HS samples, the most dominant components were monoterpene hydrocarbons. On the other hand, the essential oils consisted mainly of sesquiterpenoids, representing 73.4% of the root and 63.4% of the aerial parts essential oil. The results of antibacterial assay showed that the aerial parts essential oil and MeOH extract have no antibacterial activity, while the root essential oil and extract showed some activity. Both of the tested essential oils exhibited anticholinesterase activity (47.65% and 50.88%, respectively); MeOH extract of the root showed only 8.40% inhibition, while aerial part extract acted as an activator of cholinesterase. Regarding the antioxidant activity, extracts were found to be more effective than the essential oils. © 2017 Wiley-VHCA AG, Zurich, Switzerland.

  9. Comparison study of moisture content, colour properties and essential oil compounds extracted by hydrodistillation and supercritical fluid extraction between stem and leaves of lemongrass (Cymbopogun citratus)

    Science.gov (United States)

    Kamaruddin, Shazlin; Mustapha, Wan Aida Wan; Haiyee, Zaibunnisa Abdul

    2018-04-01

    The objectives of this study were to compare the properties of moisture content, colour and essential oil compounds between stem and leaves of lemongrass (Cymbopogun citratus). The essential oil was extracted using two different methods which are hydrodistillation and supercritical fluid extraction (SFE). There was no significant difference of moisture content between stem and leaves of lemongrass. The lightness (L) and yellowness (+b) values of the stems were significantly higher (pleaves. The highest yield of essential oil was obtained by extraction using supercritical fluid extraction (SFE) in leaves (˜ 0.7%) by treatment at 1700psi and 50°C. The main compound of extracted essential oil was citral (geranial and neral).

  10. A Review of Extraction Techniques for Avocado Oil.

    Science.gov (United States)

    Qin, Xiaoli; Zhong, Jinfeng

    2016-11-01

    Avocado fruit is rich in monounsaturated fat and contains relatively high level of important lipid-soluble compounds such as vitamin E, β-sitosterol and carotenoids. The consumption of avocado fruit is highly related to its potential benefits. However, with the increase of avocado production, short time of maturation and easy oxidation of avocado fruit are the main problem for producers. The production of oil from avocado fruit, thus, is highly promoted. This paper discusses the effects of different extraction methods on chemical composition and yield of oils from avocado fruits.

  11. Extraction of phenolic compounds from extra virgin olive oil by a natural deep eutectic solvent: Data on UV absorption of the extracts.

    Science.gov (United States)

    Paradiso, Vito Michele; Clemente, Antonia; Summo, Carmine; Pasqualone, Antonella; Caponio, Francesco

    2016-09-01

    This data article refers to the paper "Towards green analysis of virgin olive oil phenolic compounds: extraction by a natural deep eutectic solvent and direct spectrophotometric detection" [1]. A deep eutectic solvent (DES) based on lactic acid and glucose was used as green solvent for phenolic compounds. Eight standard phenolic compounds were solubilized in the DES. Then, a set of extra virgin olive oil (EVOO) samples (n=65) were submitted to liquid-liquid extraction by the DES. The standard solutions and the extracts were analyzed by UV spectrophotometry. This article reports the spectral data of both the standard solutions and the 65 extracts, as well as the total phenolic content of the corresponding oils, assessed by the Folin-Ciocalteu assay.

  12. Antioxidant activity, phenolic content, and peroxide value of essential oil and extracts of some medicinal and aromatic plants used as condiments and herbal teas in Turkey.

    Science.gov (United States)

    Ozcan, Mehmet Musa; Erel, Ozcan; Herken, Emine Etöz

    2009-02-01

    The antioxidant activity, total peroxide values, and total phenol contents of several medicinal and aromatic plant essential oil and extracts from Turkey were examined. Total phenolic contents were determined using a spectrophotometric technique and calculated as gallic acid equivalents. Total antioxidant activity of essential oil and extracts varied from 0.6853 to 1.3113 and 0.3189 to 0.6119 micromol of Trolox equivalents/g, respectively. The total phenolic content of essential oil ranged from 0.0871 to 0.5919 mg of gallic acid/g dry weight. However, the total phenolic contents of extracts were found to be higher compared with those of essential oils. The amount of total peroxide values of oils varied from 7.31 (pickling herb) to 58.23 (bitter fennel flower) mumol of H(2)O(2)/g. As a result, it is shown that medicinal plant derivatives such as extract and essential oils can be useful as a potential source of total phenol, peroxide, and antioxidant capacity for protection of processed foods.

  13. Extraction, isolation and characterisation of oil bodies from pumpkin seeds for therapeutic use.

    Science.gov (United States)

    Adams, Gary G; Imran, Shahwar; Wang, Sheng; Mohammad, Abubaker; Kok, M Samil; Gray, David A; Channell, Guy A; Harding, Stephen E

    2012-10-15

    Pumpkin, a member of the Cucurbitaceae family has been used frequently as functional medicines for therapeutic use. Several phytochemicals such as polysaccharides, phenolic glycosides, 13-hydroxy-9Z, 11E-octadecatrienoic acid from the leaves of pumpkin, proteins from germinated seeds, have been isolated. Here the influence of pH, ionic strength, and temperature on the properties and stability of oil bodies from pumpkin (Cucurbita) were determined with a view to patterning oil body size and structure for future therapeutic intervention. Oil bodies from pumpkin seeds were extracted, isolated, characterised using optical microscopy, zeta potential and particle size distribution obtained. During microscopic analysis, the oil bodies were more intact and in an integrated form at the time of extraction but were ruptured with time. Water extracted oil bodies were spherical for all four layers where cream had larger oil bodies then upper curd. Lower curd and supernatant had considerably smaller size with lower curd densely packed and seemed to be rich in oil bodies than any of the four layers. At pH 3, in the absence of salt, the zeta potential is approximately +30 mV, but as the salt concentration increases, the ζ potential rises at 10 mM but then decreases over the salt range. This trend continues for the upper curd, lower curd and the supernatant and the degree of the reduction (mV) in zeta potential is of the order creampumpkin seed oil bodies at an increasing pH (3, 7.4 and 9) and salt concentration (0, 10, 50 and 100 mM) across all four layers. The lowest average size distributions are seen at pH 7.4 across all four layers especially within the cream and upper curd layers. At pH 3 and 9, the highest average size distributions are seen in the lower curd and cream layers. Oil bodies can be extracted, isolated and from pumpkins using an aqueous extraction method and may prove to be a useful new source of lipids for application in patterning therapeutics for clinical use

  14. Fate of 14 C Labelled fungicides maneb and mancozeb during processing of contaminated soybean oil

    International Nuclear Information System (INIS)

    Zayed, S.M.A.D.; Hegazi, B.

    1991-01-01

    Soybeans from plants previously treated with 14 C-maneb and 14 C-mancozeb contain 0.62% and 3.15% of the applied dose, respectively. Crude soybean soil extracted from seeds was subjected to different refining processes. The effect of commercial refining processes, namely: alkali treatment, bleacking, winterization and deoderization on the nature and magnitude of the original residues was investigated. A high percentage of the residues was eliminated by alkali refining and deoderization processes. Analysis of residues after each step showed the ETU, ETM and ETD, in addition to two unknowns where the main 14 C-residues present in the oil. The refined oil contains around 1% of the residues originally present in the crude soybean oil.4 tab

  15. Technical and economic study of a mobile system for extraction of eucalyptus essential oil

    Directory of Open Access Journals (Sweden)

    Gisele Aparecida Vivan

    2011-03-01

    Full Text Available The production of essential oils has become increasing in Brazil, especially considering the benefits that certain substances can add to health and range of cosmetics, toiletries and drugs that originate in its processing. Based on these conditions and in the vast area of the Rio Grande do Sul where it is being implanted the culture of eucalyptus, this study seeks ways to boost the economic structure of culture, seeking to generate new business opportunities through the extraction of oil contained in the leaves Eucalyptus, a byproduct of the paper industry, the current main economic interest of culture. Based on these assumptions, it was elaborated a conceptual design of a mobile equipment able to meet the processing demand of the crop, determining a diagram processing flow and fitting the equipment to meet this demand. Subsequently, it was evaluated the technical and economic feasibility of deploying the mobile extraction system for essential oil of eucalyptus in the southern region of Rio Grande do Sul, conducting technical studies for the improvement and efficiency of the conceptual design and economic feasibility analysis to determine variables that determine the success of the project. It was conclude that the conceptual design has beneficial aspects, especially regarding the mobility, flexibility of use, minimization of empty spaces and water use in semi-closed circuit. In the analysis of economic feasibility, the simulated scenarios showed positive values for Net Present Value, Internal Rate of Return above the minimum rate of attractiveness and capital Payback relatively short, even for the scenarios considered critical.

  16. Effect of matrix pretreatment on the supercritical CO2 extraction of Satureja montana essential oil

    Directory of Open Access Journals (Sweden)

    Damjanović-Vratnica Biljana

    2016-01-01

    Full Text Available The effect of different matrix pretreatment of winter savory(Satureja montana L. on the supercritical CO2(SC-CO2 extraction - yield, composition and antimicrobial activity of extracts and essential oil (EO was investigated. Herb matrix was submitted to conventional mechanical grinding, physical disruption by fast decompression of supercritical and subcritical CO2 and physical disruption by mechanical compression. The analyses of the essential oil obtained by SC-CO2 extraction and hydrodistillation were done by GC/FID method. Major compounds in winter savory EO obtained by SC-CO2 extraction and hydrodistillation were: thymol (30.4-35.4% and 35.3%, carvacrol (11.5-14.1% and 14.1%, γ-terpinene (10.2-11.4% and 9.1% and p-cymene (8.3-10.1% and 8.6%, respectively. The gained results revealed that physical disruption of essential oils glands by fast CO2 decompression in supercritical region (FDS achieved the highest essential oil yield as well as highest content of thymol, carvacrol and thymoquinone. Antimicrobial activity of obtained winter savory SC-CO2 extracts was the same (FDS or weaker compared to essential oil obtained by hydrodistillation.

  17. DEVELOPMENT OF CONTINUOUS SOLVENT EXTRACTION PROCESSES FOR COAL DERIVED CARBON PRODUCTS

    Energy Technology Data Exchange (ETDEWEB)

    Elliot B. Kennel; Philip L. Biedler; Chong Chen; Dady Dadyburjor; Liviu Magean; Peter G. Stansberry; Alfred H. Stiller; John W. Zondlo

    2005-04-13

    The purpose of this DOE-funded effort is to develop continuous processes for solvent extraction of coal for the production of carbon products. These carbon products include materials used in metals smelting, especially in the aluminum and steel industries, as well as porous carbon structural material referred to as ''carbon foam'' and carbon fibers. A process has been developed which results in high quality binder pitch suitable for use in graphite electrodes or carbon anodes. A detailed description of the protocol is given by Clendenin. Briefly, aromatic heavy oils are hydro-treated under mild conditions in order to increase their ability to dissolve coal. An example of an aromatic heavy oil is Koppers Carbon Black Base (CBB) oil. CBB oil has been found to be an effective solvent and acceptably low cost (i.e., significantly below the market price for binder pitch, or about $280 per ton at the time of this writing). It is also possible to use solvents derived from hydrotreated coal and avoid reliance on coke oven recovery products completely if so desired.

  18. The Effectiveness of Rambutan (Nephelium lappaceum L.) Extract in Stabilization of Sunflower Oil under Accelerated Conditions.

    Science.gov (United States)

    Mei, Winne Sia Chiaw; Ismail, Amin; Esa, Norhaizan Mohd; Akowuah, Gabriel Akyirem; Wai, Ho Chun; Seng, Yim Hip

    2014-05-09

    The oxidative properties of sunflower oil supplemented with rambutan extract, (crude extract and its fractionated fraction, SF II) in comparison with synthetic antioxidant were investigated. The supplemented sunflower oils were stored under accelerated conditions for 24 days at 60 °C. For every 6-day interval, the oxidative properties of the supplemented sunflower oil were evaluated based on the following tests, namely peroxide value, p-anisidine value, Thiobarbituric Acid Reactive Substances (TBARS) assay, iodine value and free fatty acids. The total oxidation (TOTOX) values were also calculated based on the peroxide values and p-anisidine values. Rambutan extract is a potential source of antioxidant. The oxidative activities of the extracts at all concentrations were significantly (p rambutan extract could be used as a potential alternative source of antioxidant in the oil industry or other fat-based products to delay lipid oxidation.

  19. Green ultrasound-assisted extraction of carotenoids based on the bio-refinery concept using sunflower oil as an alternative solvent.

    Science.gov (United States)

    Li, Ying; Fabiano-Tixier, Anne Sylvie; Tomao, Valérie; Cravotto, Giancarlo; Chemat, Farid

    2013-01-01

    A green, inexpensive and easy-to-use method for carotenoids extraction from fresh carrots assisted by ultrasound was designed in this work. Sunflower oil was applied as a substitute to organic solvents in this green ultrasound-assisted extraction (UAE): a process which is in line with green extraction and bio-refinery concepts. The processing procedure of this original UAE was first compared with conventional solvent extraction (CSE) using hexane as solvent. Moreover, the UAE optimal conditions for the subsequent comparison were optimized using response surface methodology (RSM) and ultra performance liquid chromatography--diode array detector--mass spectroscopy (UPLC-DAD-MS). The results showed that the UAE using sunflower as solvent has obtained its highest β-carotene yield (334.75 mg/l) in 20 min only, while CSE using hexane as solvent obtained a similar yield (321.35 mg/l) in 60 min. The green UAE performed under optimal extraction conditions (carrot to oil ratio of 2:10, ultrasonic intensity of 22.5 W cm(-2), temperature of 40 °C and sonication time of 20 min) gave the best yield of β-carotene. Copyright © 2012 Elsevier B.V. All rights reserved.

  20. Solvent extraction of jojoba oil from pre-pressed jojoba meal

    Directory of Open Access Journals (Sweden)

    El Haron, Dalia E.

    2004-06-01

    Full Text Available The solvent extraction process of jojoba oil from the meal cake obtained after the mechanical pressing of jojoba seeds was studied. Commercial hexane and petroleum ether were used as solvents and the extraction was carried out at temperatures ranging from 30 to 55 °C using solvent-to-solid ratios, R between 2 and 15 L/kg. The equilibrium compositions of the solvent and solid phases were determined. Based on the equilibrium data, the partition coefficient or distribution ratio, D of the oil between both phases was estimated. Also, the number of extraction stages necessary to achieve a certain degree of oil recovery has been determined using different hexane-to-meal ratios. Jojoba oil was also tested for its physical and chemical properties including chemical composition, percentage fatty acid, peroxide value, flash point, fire point, pour point, refractive index, saponification and iodine values. The stability of jojoba oil during storage at room temperature and during heat treatment was also studied.Se ha estudiado el proceso de extracción con disolventes del aceite contenido en la harina residual del prensado mecánico de las semillas de jojoba. Como disolventes se han utilizado hexano técnico y éter de petróleo, habiéndose efectuado extracciones a temperaturas comprendidas entre 30 ºC y 55 ºC , con relaciones de disolvente a sólido, R, de entre 12 y 15 L/kg. Se han determinado las composiciones del extracto y del residuo sólido en el equilibrio y a partir de los datos de equilibrio, se ha estimado el coeficiente de partición o cociente de distribución, D, del aceite entre ambas fases. Asimismo, se ha determinado el número de etapas de extracción necesarias para conseguir un cierto grado de recuperación del aceite, utilizando diferentes relaciones entre hexano y harina. También se han determinado las propiedades físicas y químicas del aceite de jojoba, incluyendo la composición química, el porcentaje de ácidos grasos

  1. Oil extracted from spent coffee grounds for bio-hydrotreated diesel production

    International Nuclear Information System (INIS)

    Phimsen, Songphon; Kiatkittipong, Worapon; Yamada, Hiroshi; Tagawa, Tomohiko; Kiatkittipong, Kunlanan; Laosiripojana, Navadol; Assabumrungrat, Suttichai

    2016-01-01

    Highlights: • The spent coffee oil with high FFAs was hydrotreated to liquid biofuel. • Pd/C gave higher olefins while NiMo/γ-Al_2O_3 gave higher isoparaffins liquid products. • The diesel fuel fraction can have a cetane number as high as 80. • The physiochemical properties of diesel fraction comply with commercial standard. - Abstract: Oil extracted from spent coffee grounds is utilized as a renewable source for bio-hydrotreated fuel production. In the present work, oil yield up to 13% can be obtained by Soxhlet extraction with hexane as a solvent. As the extracted oil contained high content of free fatty acids (6.14%), therefore one step alkali-catalyzed for ester based biodiesel production is impractical. Hydrotreating of extracted oil was performed over two catalysts i.e. NiMo/γ-Al_2O_3 and Pd/C with different operating parameters i.e. reaction time, operating temperature, and H_2/oil. It was found that the reaction time of 2 h and the reaction temperature of 400 °C are favorable operating conditions. The liquid products mostly consisted of n-pentadecane and n-heptadecane, which contain one carbon atom shorter than the corresponding fatty acid (C_n_−_1) i.e. palmitic and stearic acid, respectively. Unfavorable cracking of diesel product is pronounced at high temperature and prolonged reaction time. In addition, although increased H_2/oil promoted overall reaction and hydrodeoxygenation activity (C_n_−_1/C_n decreased) for both catalysts, hydrocracking is enhanced over Pd/C, leading to significant increase in gasoline yield. Moreover, Pd/C gave higher olefin content in liquid product (22.3 wt%) than NiMo/γ-Al_2O_3 (4.8 wt%). However, NiMo/γ-Al_2O_3 shows higher isomerization activity. The amount of isoparaffins catalyzed by NiMo/γ-Al_2O_3 and Pd/C were 10.8 and 1.7 wt%, respectively. Physiochemical analysis of the diesel fraction exhibit satisfactory properties. The density and kinematic viscosity were consistent with the specification of

  2. Extract of Zanthoxylum bungeanum maxim seed oil reduces ...

    African Journals Online (AJOL)

    Purpose: To investigate the anti-hyperlipidaemic effect of extract of Zanthoxylum bungeanum Maxim. seed oil (EZSO) on high-fat diet (HFD)-induced hyperlipidemic hamsters. Methods: Following feeding with HFD for 30 days, hyperlipidemic hamsters were intragastrically treated with EZSO for 60 days. Serum levels of ...

  3. Microwave-assisted extraction of silkworm pupal oil and evaluation of its fatty acid composition, physicochemical properties and antioxidant activities.

    Science.gov (United States)

    Hu, Bin; Li, Cheng; Zhang, Zhiqing; Zhao, Qing; Zhu, Yadong; Su, Zhao; Chen, Yizi

    2017-09-15

    Microwave-assisted extraction (MAE) of oil from silkworm pupae was firstly performed in the present research. The response surface methodology was applied to optimize the parameters for MAE. The yield of oil by MAE was 30.16% under optimal conditions of a mixed solvent consisting of ethanol and n-hexane (1:1, v/v), microwave power (360W), liquid to solid ratio (7.5/1mL/g), microwave time (29min). Moreover, oil extracted by MAE was quantitatively (yield) and qualitatively (fatty acid profile) similar to those obtained using Soxhlet extraction (SE), but oil extracted by MAE exhibited favourable physicochemical properties and oxidation stability. Additionally, oil extracted by MAE had a higher content of total phenolic, and it showed stronger antioxidant activities. Scanning electron microscopy revealed that microwave technique efficiently promoted the release of oil by breaking down the cell structure of silkworm pupae. Therefore, MAE can be an effective method for the silkworm pupal oil extraction. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Effect of oil extraction assisted by ultrasound on the physicochemical properties and fatty acid profile of pumpkin seed oil (Cucurbita pepo).

    Science.gov (United States)

    Hernández-Santos, Betsabé; Rodríguez-Miranda, Jesús; Herman-Lara, Erasmo; Torruco-Uco, Juan G; Carmona-García, Roselis; Juárez-Barrientos, José M; Chávez-Zamudio, Rubí; Martínez-Sánchez, Cecilia E

    2016-07-01

    The effects of amplitude and time of ultrasound-assisted extraction on the physicochemical properties and the fatty acid profile of pumpkin seed oil (Cucurbita pepo) were evaluated. Ultrasound time (5-30 min) and the response variables amplitude (25-100%), extraction yield, efficiency, oxidative stability in terms of the free fatty acids (FFA) of the plant design comprising two independent experiments variables, peroxide (PV), p-anisidine (AV), totox value (TV) and the fatty acid profile were evaluated. The results were analyzed by multiple linear regression. The time and amplitude showed significant differences (P<0.05) for all variables. The highest yield of extraction was achieved at 5 min and amplitude of 62.5% (62%). However, the optimal ultrasound-assisted extraction conditions were as follows: ultrasound time of 26.34 min and amplitude of 89.02%. All extracts showed low FFA (2.75-4.93% oleic acid), PV (1.67-4.68 meq/kg), AV (1.94-3.69) and TV (6.25-12.55) values. The main fatty acids in all the extracts were oleic and linoleic acid. Therefore, ultrasound-assisted oil extraction had increased performance and reduced extraction time without affecting the oil quality. Copyright © 2016 Elsevier B.V. All rights reserved.

  5. Effect of Processing on Physiochemical Properties and Fatty Acid Composition of Fluted Pumpkin (Telfairia occidentails) Seed Oil

    International Nuclear Information System (INIS)

    Alademeyin, J. O.; Arawande, J. O.

    2016-01-01

    This paper reports the physicochemical properties and fatty acid composition of the seed oil extracted from fluted pumpkin (Telfairia occidentalis). The extracted oil was degummed, neutralised and bleached. The oil yield was 42.26±0.20%. The specific gravity (at 25 degree C) of the oil was 0.923±0.003 and the refractive index (at 25 degree C) was 1.475±0.002. Processing of the crude oil resulted in progressive decrease in turbidity, colour, free fatty acid, acid value, peroxide value and saponification value. However, there was increase in smoke point (243.00±0.03 to 253.00±0.03 degree C), flash point (285.00±1.20 to 304.0 1.10 degree C) and fire point (345.001.10 to 358.0 1.55 degree C) as well as iodine value (113.00 to 121.50 g/100 g) and fatty acid composition during the processing of the oil. The fatty acids detected in the oil samples were myristic, palmitic, stearic, oleic, arachidic, behenic, linoleic and linolenic acids. The predominant fatty acid was oleic acid (47.40-47.90%) followed by linoleic acid (26.36-30.44%) while the least fatty acid was linolenic acid (0.01-0.05%). (author)

  6. Partition behavior of virgin olive oil phenolic compounds in oil-brine mixtures during thermal processing for fish canning.

    Science.gov (United States)

    Sacchi, Raffaele; Paduano, Antonello; Fiore, Francesca; Della Medaglia, Dorotea; Ambrosino, Maria Luisa; Medina, Isabel

    2002-05-08

    The chemical modifications and partitioning toward the brine phase (5% salt) of major phenol compounds of extra virgin olive oil (EVOO) were studied in a model system formed by sealed cans filled with oil-brine mixtures (5:1, v/v) simulating canned-in-oil food systems. Filled cans were processed in an industrial plant using two sterilization conditions commonly used during fish canning. The partitioning of phenolic compounds toward brine induced by thermal processing was studied by reversed-phase high-performance liquid chromatographic analysis of the phenol fraction extracted from oils and brine. Hydroxytyrosol (1), tyrosol (2), and the complex phenolic compounds containing 1 and 2 (i.e., the dialdehydic form of decarboxymethyl oleuropein aglycon 3, the dialdehydic form of decarboxymethyl ligstroside aglycon 4, and the oleuropein aglycon 6) decreased in the oily phase after sterilization with a marked partitioning toward the brine phase. The increase of the total amount of 1 and 2 after processing, as well as the presence of elenolic acid 7 released in brine, revealed the hydrolysis of the ester bond of hydrolyzable phenolic compounds 3, 4, and 6 during thermal processing. Both phenomena (partitioning toward the water phase and hydrolysis) contribute to explain the loss of phenolic compounds exhibited by EVOO used as filling medium in canned foods, as well as the protection of n-3 polyunsaturated fatty acids in canned-in-EVOO fish products.

  7. Antimicrobial and antifungal activities of the extracts and essential oils of Bidens tripartita.

    Directory of Open Access Journals (Sweden)

    Michał Tomczyk

    2008-12-01

    Full Text Available The aim of this study was to determine the antibacterial and antifungal properties of the extracts, subextracts and essential oils of Bidens tripartita flowers and herbs. In the study, twelve extracts and two essential oils were investigated for activity against different Gram-positive Bacillus subtilis, Micrococcus luteus, Staphylococcus aureus, Gram-negative bacteria Escherichia coli, E. coli (beta-laktamase+, Klebsiella pneumoniae (ESBL+, Pseudomonas aeruginosa and some fungal organisms Candida albicans, C. parapsilosis, Aspergillus fumigatus, A. terreus using a broth microdilution and disc diffusion methods. The results obtained indicate antimicrobial activity of the tested extracts (except butanolic extracts, which however did not inhibit the growth of fungi used in this study. Bacteriostatic effect of both essential oils is insignificant, but they have strong antifungal activity. These results support the use of B. tripartita to treat a microbial infections and it is indicated as an antimicrobial and antifungal agent, which may act as pharmaceuticals and preservatives.

  8. In vitro antioxidant activities of extract and oil from roselle (Hibiscus sabdariffa L.) seed against sunflower oil autoxidation.

    Science.gov (United States)

    Nyam, K L; Teh, Y N; Tan, C P; Kamariah, L

    2012-08-01

    In order to overcome the stability problems of oils and fats, synthetic antioxidants such as butylated hydroxyanisole (BHA), butylated hydroxytoluene (BHT) and tert-butyl hydroquinone (TBHQ) have widespread use as food additives in many countries. Recent reports reveal that these compounds may be implicated in many health risks, including cancer and carcinogenesis. Hence, there is a move towards the use of natural antioxidants of plant origin to replace these synthetic antioxidants. In this study, roselle seed oil (RSO) and extract (RSE) were mixed with sunflower oil, respectively to monitor degradation rate and investigate antioxidant activity during accelerated storage. The antioxidant activity was found to stabilise sunflower oil of various samples and in the order of RSE>RSO>tocopherol>sunflower oil. The total percentage increased after 5 days of storage period in free fatty acid (FFA), peroxide value (PV) and anisidine value (AV). Total oxidation value (TOx) of sunflower oil supplemented with 1500 ppm RSE was 33.3%, 47.7%, 14.5%, and 45.5%, respectively. While the total percentage increased under different analysis methods, sunflower oil supplemented with 5% RSO was 17.2%, 60.4%, 36.2% and 59.0% in the order of FFA, PV, AV and TOTOX. Both RSO and RSE were found to be more effective in stabilisation of sunflower oil compared to tocopherol. Total phenolic content of RSE was 46.40 +/- 1.51 mg GAE/100g of oil while RSO was 12.51 +/- 0.15 mg GAE/ 100g of oil. The data indicates that roselle seed oil and seed extract are rich in phenolics and antioxidant activities and may be a potential source of natural antioxidants.

  9. Kinetics of hydrocarbon extraction from oil shale using biosurfactant producing bacteria

    International Nuclear Information System (INIS)

    Haddadin, Malik S.Y.; Abou Arqoub, Ansam A.; Abu Reesh, Ibrahim; Haddadin, Jamal

    2009-01-01

    This study was done to extract hydrocarbon compounds from El-Lajjun oil shale using biosurfactant produced from two strains Rhodococcus erythropolis and Rhodococcus ruber. The results have shown that, optimal biosurfactant production was found using naphthalene and diesel as a carbon source for R. erthropolis and R. ruber, respectively. Optimum nitrogen concentration was 9 g/l and 7 g/l for R. erthropolis and R. ruber, respectively. Optimum K 2 HPO 4 to KH 2 PO 4 ratio, temperature, pH, and agitation speeds were 2:1, 37 deg. C, 7 and 200 rpm. Under optimal conditions R. erthropolis and R. ruber produced 5.67 and 6.9 g/l biosurfactant, respectively. Maximum recovery of oil achieved with hydrogen peroxide pre-treatment was 25% and 26% at biosurfactant concentration of 8 g/l and 4 g/l for R. erthropolis and R. ruber, respectively. The extent desorption of hydrocarbons from the pre-treated oil shale by biosurfactant were inversely related to the concentration of high molecular weight hydrocarbons, asphaltenes compounds. Pre- treatment of oil shale with hydrogen peroxide produced better improvement in aromatic compounds extraction in comparison with improvement which resulted from demineralization of the oil shale

  10. Gill histopathology of goldfish exposed to oil sands processed-waters

    International Nuclear Information System (INIS)

    Nero, V.; Farwell, A.J.; Dixon, D.G.; Lee, L.E.J.

    2002-01-01

    Large volumes of processed wastewater are generated through the oil extraction process at Alberta's Athabasca oil sand deposit. These wastewaters are very toxic to aquatic biota because they are high in salinity and consist of napthenic acids and polycyclic aromatic hydrocarbons (PAH). In this study, goldfish were caged in 3 different experimental ponds in order to evaluate the biological effects of aquatic reclamation alternatives for process-affected waters. The first pond was a control pond, while the other 2 ponds consisted of known and varying chemicals. The fish were exposed to the ponds for 19 days. Those in the pond with elevated levels of napthenic acids and high salinity exhibited severe gill histopathological changes. Alterations included epithelial hyperplasia resulting in severe lamellar fusion, chloride cell hyperplasia, and lamellar edema, all of which were believed to be defense responses of the fish. Additional severe gill alterations were also observed that may indicate the direct negative effects of oil sands processed-water on fish. Exposed goldfish also showed signs of necrosis and degenerative changes resulting in desquamation of the epithelial surfaces of the gill, which are symptoms seen in free-range exposure of yellow perch, a native fish species, at the same sites and exposure times

  11. Gill histopathology of goldfish exposed to oil sands processed-waters

    Energy Technology Data Exchange (ETDEWEB)

    Nero, V.; Farwell, A.J.; Dixon, D.G. [Waterloo Univ., ON (Canada). Dept. of Biology; Lister, A.; Van Der Kraak, G.J. [Guelph Univ., ON (Canada); Lee, L.E.J. [Wilfred Laurier Univ., Waterloo, ON (Canada). Dept. of Biology

    2002-07-01

    Large volumes of processed wastewater are generated through the oil extraction process at Alberta's Athabasca oil sand deposit. These wastewaters are very toxic to aquatic biota because they are high in salinity and consist of napthenic acids and polycyclic aromatic hydrocarbons (PAH). In this study, goldfish were caged in 3 different experimental ponds in order to evaluate the biological effects of aquatic reclamation alternatives for process-affected waters. The first pond was a control pond, while the other 2 ponds consisted of known and varying chemicals. The fish were exposed to the ponds for 19 days. Those in the pond with elevated levels of napthenic acids and high salinity exhibited severe gill histopathological changes. Alterations included epithelial hyperplasia resulting in severe lamellar fusion, chloride cell hyperplasia, and lamellar edema, all of which were believed to be defense responses of the fish. Additional severe gill alterations were also observed that may indicate the direct negative effects of oil sands processed-water on fish. Exposed goldfish also showed signs of necrosis and degenerative changes resulting in desquamation of the epithelial surfaces of the gill, which are symptoms seen in free-range exposure of yellow perch, a native fish species, at the same sites and exposure times.

  12. Cytotoxic effects of Pinus eldarica essential oil and extracts on HeLa and MCF-7 cell lines.

    Science.gov (United States)

    Sarvmeili, Najmeh; Jafarian-Dehkordi, Abbas; Zolfaghari, Behzad

    2016-12-01

    Several attempts have so far been made in the search of new anticancer agents of plant origin. Some studies have reported that different species of Pine genus possess cytotoxic activities against various cancer cell lines. In the present study, we evaluated the cytotoxic effects of Pinus eldarica bark and leaf extracts or leaf essential oil on HeLa and MCF-7 tumor cell lines. Hydroalcoholic and phenolic extracts and the essential oil of plant were prepared. Total phenolic contents of the extracts were measured using Folin-Ciocalteu reagent. Essential oil components were determined by gas chromatography-mass spectroscopy (GC-MS). Cytotoxic activity of the extracts and essential oil against HeLa and MCF-7 tumor cell lines were assessed by 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT) assay. The polyphenolic content of hydroalcoholic and phenolic extracts of the bark and hydroalcoholic extract of the leaf were 48.31%, 47.2%, and 8.47%, respectively. According to the GC-MS analysis, the major components of the leaf oil of P. eldarica were: β -caryophyllene (14.8%), germacrene D (12.9%), α-terpinenyl acetate (8.15%), α -pinene (5.7%), and -α humulene (5.9%). Bark extracts and leaf essential oil of P. eldarica significantly reduced the viability of both HeLa and MCF-7 cells in a concentration dependent manner. However, leaf extract showed less inhibitory effects against both cell lines. The essential oil of P. eldarica was more cytotoxic than its hydroalcoholic and phenolic extracts. The terpenes and phenolic compounds were probably responsible for cytotoxicity of P. eldarica . Therefore, P. eldarica might have a good potential for active anticancer agents.

  13. Antioxidant Activity of Potato Peel Extracts in a Fish-RapeseedOil Mixture and in Oil-in-Water Emulsions

    DEFF Research Database (Denmark)

    Farvin, Sabeena; Nielsen, Nina Skall; Jacobsen, Charlotte

    2010-01-01

    The objectives of the present work were (a) to extract the phenolic fraction from the peels of two Danish varieties of potatoes, viz. Sava and Bintje, and examine their antioxidant capacity in in-vitro systems (b) to evaluate the effect of these extracts on the storage stability of a fish- rapeseed...... oil mixture and oil-in-water emulsions. Multiple antioxidant activity of the potato peel extracts was evident from in-vitro systems as they showed strong reducing power, radical scavenging ability, ferrous ion chelating activity and prevented oxidation in a liposome model system. The Sava variety...... in emulsions. Thus, the results of the present study show the possibility of utilizing waste potato peel as a promising source of natural antioxidants for retarding lipid oxidation....

  14. Concentrations of tocols and γ-oryzanol compounds in rice bran oil obtained by fractional extraction with supercritical carbon dioxide.

    Science.gov (United States)

    Yoon, Sung Won; Pyo, Young-Gil; Lee, Junsoo; Lee, Jeom-Sig; Kim, Byung Hee; Kim, In-Hwan

    2014-01-01

    Rice bran oil (RBO) is a good source of several commercially important bioactive phytochemicals, such as tocols (i.e. tocopherols and tocotrienols) and ferulic esters of sterols (i.e. γ-oryzanol). The aims of the present study were to examine the effects of different pressure and temperature combinations on the fractional extraction of RBO using supercritical carbon dioxide (SC-CO2) and to assess the levels of tocols homologues and γ-oryzanol components in the resulting oil fractions. Fractional extraction of rice bran oil was performed using SC-CO2 at either 27.6 or 41.4 MPa and either 40 or 60°C. The effects of the four different pressure and temperature combinations on the levels of seven tocols homologues (α-, β-, γ- and δ-tocopherol and α-, γ- and δ-tocotrienol) and the four major components of γ-oryzanol in the resulting oil fractions were investigated. Superior extraction efficiency was obtained using the higher pressure of 41.4 MPa. The tocols (particularly α-tocopherol and α-tocotrienol) were recovered early in the extraction process, while the γ-oryzanol compounds were obtained in the later stages. With regard to SC-CO2 extraction, tocols are more soluble than γ-oryzanol components, α-tocopherol is the most soluble of the tocols and the four γ-oryzanol components all have similar solubilities. Valuable data on solubilities of tocols homologues in SC-CO2 were provided from present study.

  15. Analysis of essential oils from Voacanga africana seeds at different hydrodistillation extraction stages: chemical composition, antioxidant activity and antimicrobial activity.

    Science.gov (United States)

    Liu, Xiong; Yang, Dongliang; Liu, Jiajia; Ren, Na

    2015-01-01

    In this study, essential oils from Voacanga africana seeds at different extraction stages were investigated. In the chemical composition analysis, 27 compounds representing 86.69-95.03% of the total essential oils were identified and quantified. The main constituents in essential oils were terpenoids, alcohols and fatty acids accounting for 15.03-24.36%, 21.57-34.43% and 33.06-57.37%, respectively. Moreover, the analysis also revealed that essential oils from different extraction stages possessed different chemical compositions. In the antioxidant evaluation, all analysed oils showed similar antioxidant behaviours, and the concentrations of essential oils providing 50% inhibition of DPPH-scavenging activity (IC50) were about 25 mg/mL. In the antimicrobial experiments, essential oils from different extraction stages exhibited different antimicrobial activities. The antimicrobial activity of oils was affected by extraction stages. By controlling extraction stages, it is promising to obtain essential oils with desired antimicrobial activities.

  16. Optimization process condition for deacidification of palm oil by liquid-liquid extraction using NADES (Natural Deep Eutectic Solvent)

    Science.gov (United States)

    Israyandi, Zahrina, Ida; Mulia, Kamarza

    2017-03-01

    One of many steps in palm oil refining process is deacidification which aims to separate free fatty acids and other compounds from the oil. The deacidification process was using a green solvent, known as NADES, that consisted of betaine monohydrate and propionic acid at molar ratio of 1:8. In this study, the process conditions were optimized using the response surface method (RSM) through central composite design in order to predict the maximum distribution coefficient of palmitic acid. The obtained regression equation of the basic model for optimization was: y = 0.717 + 0.003x1 + 0.043 x2 + 0.148x3 - 0.005 x1x1 - 0.030 x2x2 + 0.047 x3x3 - 0.008 x1x2 + 0.008 x1x3 + 0.033 x2x3. The independent variables are x1 ≡ temperature (40, 60, 80 °C), x2≡ amount of palmitic acid in the palm oil (2, 5, 8 %) and x3 ≡ mass ratios of oil to NADES (1:2, 1:1, 2:1). The optimum process condition found was temperature of 62.3°C, palmitic acid content of 8%, and NADES to palm oil mass ratio of 1:2, resulting in the maximum distribution coefficient of 0.96.

  17. Pumpkin Seed Oil Extracted From Cucurbita maxima Improves Urinary Disorder in Human Overactive Bladder.

    Science.gov (United States)

    Nishimura, Mie; Ohkawara, Tatsuya; Sato, Hiroji; Takeda, Hiroshi; Nishihira, Jun

    2014-01-01

    The pumpkin seed oil obtained from Cucurbita pepo has been shown to be useful for the treatment of nocturia in patients with urinal disorders in several western countries. In this study, we evaluated the effect of the pumpkin seed oil from Cucurbita maxima on urinary dysfunction in human overactive bladder (OAB). Forty-five subjects were enrolled in this study. An extract of pumpkin seed oil from C. maxima (10 g of oil/day) was orally administrated for 12 weeks. After 6 and 12 weeks, urinary function was evaluated using Overactive Bladder Symptom Score (OABSS). Pumpkin seed oil from C. maxima significantly reduced the degree of OABSS in the subjects. The results from our study suggest that pumpkin seed oil extracts from C. maxima as well as from C. pepo are effective for urinary disorders such as OAB in humans.

  18. Pumpkin Seed Oil Extracted From Cucurbita maxima Improves Urinary Disorder in Human Overactive Bladder

    Science.gov (United States)

    Nishimura, Mie; Ohkawara, Tatsuya; Sato, Hiroji; Takeda, Hiroshi; Nishihira, Jun

    2014-01-01

    The pumpkin seed oil obtained from Cucurbita pepo has been shown to be useful for the treatment of nocturia in patients with urinal disorders in several western countries. In this study, we evaluated the effect of the pumpkin seed oil from Cucurbita maxima on urinary dysfunction in human overactive bladder (OAB). Forty-five subjects were enrolled in this study. An extract of pumpkin seed oil from C. maxima (10 g of oil/day) was orally administrated for 12 weeks. After 6 and 12 weeks, urinary function was evaluated using Overactive Bladder Symptom Score (OABSS). Pumpkin seed oil from C. maxima significantly reduced the degree of OABSS in the subjects. The results from our study suggest that pumpkin seed oil extracts from C. maxima as well as from C. pepo are effective for urinary disorders such as OAB in humans. PMID:24872936

  19. Effect of extraction technique on the content and antioxidant activity of crude extract of Anacyclus clavatus flowers and their essential oil composition.

    Science.gov (United States)

    Aliboudhar, Hamza; Tigrine-Kordjani, Nacéra

    2014-01-01

    Anacyclus clavatus is a plant used as food and remedy. The objective of this work was to study the effect of extraction technique on the antioxidant property, total phenol and flavonoid contents of crude extracts from A. clavatus flowers and their essential oil composition. 2,2-diphenyl-1-picrylhydrazyl (DPPH) assay, ferric-reducing power, β-carotene and total antioxidant capacity assays have demonstrated the significant antioxidant ability of different crude extracts obtained by using the following extraction methods: Soxhlet, microwave heating, heat reflux (HRE) and maceration. The activity of the extract obtained by HRE was the highest (112.06 ± 2.89 μg/mL) evaluated by the DPPH assay. Extraction of essential oil was performed by microwave-assisted hydro-distillation (MAHD) and by hydro-distillation (HD). A significant difference was observed in both essential oils, despite the common main family and major constituents, such as artemisia ketone (10.0 ± 0.8% for MAHD vs. 6.5 ± 0.5 for HD) and pinocarvone (4.1 ± 0.4% for MAHD vs. 1.1 ± 0.1% for HD).

  20. Solvent extraction of organic acids from stillage for its re-use in ethanol production process.

    Science.gov (United States)

    Castro, G A; Caicedo, L A; Alméciga-Díaz, C J; Sanchez, O F

    2010-06-01

    Stillage re-use in the fermentation stage in ethanol production is a technique used for the reduction of water and fermentation nutrients consumption. However, the inhibitory effect on yeast growth of the by-products and feed components that remains in stillage increases with re-use and reduces the number of possible recycles. Several methods such as ultrafiltration, electrodialysis and advanced oxidation processes have been used in stillage treatment prior its re-use in the fermentation stage. Nevertheless, few studies evaluating the effect of solvent extraction as a stillage treatment option have been performed. In this work, the inhibitory effect of serial stillage recycling over ethanol and biomass production was determined, using acetic acid as a monitoring compound during the fermentation and solvent extraction process. Raw palm oil methyl ester showed the highest acetic acid extraction from the aqueous phase, presenting a distribution coefficient of 3.10 for a 1:1 aqueous phase mixture:solvent ratio. Re-using stillage without treatment allowed up to three recycles with an ethanol production of 53.7 +/- 2.0 g L(-1), which was reduced 25% in the fifth recycle. Alternatively, treated stillage allowed up to five recycles with an ethanol final concentration of 54.7 +/- 1.3 g L(- 1). These results show that reduction of acetic acid concentration by an extraction process with raw palm oil methyl ester before re-using stillage improves the number of recycles without a major effect on ethanol production. The proposed process generates a palm oil methyl ester that contains organic acids, among other by-products, that could be used for product recovery and as an alternative fuel.

  1. SYNTHESIS OF BIODIESEL FROM KAPUK SEED OIL (Ceiba Pentandra L AT VARIATION STIRRING DURATION IN TRANSESTERIFICATION PROCESS

    Directory of Open Access Journals (Sweden)

    Endang Dwi Siswani

    2016-05-01

    Full Text Available The synthesis of biodiesel targeted as SNI 04-7182-2006 standard has been done from kapuk randu seed, following two steps i.e. sokhlet extraction process of kapuk seed oil from kapuk seed using n-heksane as a solvent, and the production of biodiesel from kapuk seed oil by transesterification process using methanol and KOH as catalyst. Transesterificatin process was performed at temperature 50 oC with the variation of stirring duration as followed  50, 75, 100 and 125 minutes. The kapuk randu extraction resulted  % kapuk randu seed oil, while the transestherification process resulted around 55 - 65%. The biodiesel product characteristics provided the density value of all biodiesel at stirring durations variation are suitable with SNI standard (850 – 890 kg/m3, the viscosity value of all biodiesel are  higher than the range SNI value (2,3 – 6,0 cSt. While the flash point values are lesser than SNI standard (10160 - 11000 cal/g.   Keywords: kapuk randu seed, transestherification, biodiesel

  2. Comparative study on the quality of oil extracted from two tucumã varieties using supercritical carbon dioxide

    Directory of Open Access Journals (Sweden)

    Bárbara Elizabeth Teixeira COSTA

    2016-01-01

    Full Text Available Abstract The vast Amazon region has considerable territorial peculiarities and plant species diversity, sometimes from the same botanical family, which can exhibit significant differences in physicochemical properties. From this diversity, two species stand out – Amazonas tucumã (Astrocaryum aculeatum Meyer and Pará tucumã (Astrocaryum vulgare Mart.. The research focus is to analyze, comparatively, these oleaginous fruits, their similarities, particularities and potentials regarding the oil quality extracted from two tucumã varieties from the states of Amazonas and Pará, obtained using supercritical carbon dioxide, under different extraction parameters. The results demonstrate the biometric particularities of each species, highlighting the Amazon fruit, which also showed higher oil yield using supercritical CO2 extraction. The fatty acid quality and profile aspects of the oils show their unsaturated predominance, considering carotenoid content and how the extraction temperature can influence the nutritional quality of the oils. The statistical analyses indicated that the Amazon tucumã oil is superior to the Pará tucumã oil. However, in terms of added value both oils have potential applications in various industrial segments.

  3. Effectiveness of castor oil extract on Escherichia coli and its endotoxins in root canals.

    Science.gov (United States)

    Valera, Marcia Carneiro; Maekawa, Lilian Eiko; Chung, Adriana; de Oliveira, Luciane Dias; Carvalho, Claudio Antonio Talge; Koga-Ito, Cristiane Yumi; Jorge, Antonio Olavo Cardoso

    2012-01-01

    This in vitro study sought to evaluate the effectiveness of castor oil extract used as an irrigating solution on Escherichia coli and its endotoxins in root canals. Sixty single-rooted teeth were prepared (using castor oil extract as irrigating solution) and divided into five groups (n = 12): Group 1 samples were treated with calcium hydroxide (Ca(OH)2), Group 2 samples were treated with polymyxin B, Group 3 samples were treated with Ca(OH)2 and 2% chlorhexidine gel (CHX), and Group 4 samples were treated with castor oil extract. A control group used physiological saline solution as an irrigant. Canal content samples were collected at four different times: immediately after instrumentation, seven days after instrumentation, after 14 days of intracanal medication, and seven days after removal of intracanal medication. A plating method was used to assess antimicrobial activity and the quantification of endotoxins was evaluated by the chromogenic Limulus lysate assay. Data were submitted to ANOVA and a Dunn test (a = 5%). Irrigation with castor oil extract decreased E. coli counts but had no effect on the level of endotoxins. Samples taken seven days after removal of medication revealed a significant reduction in endotoxin levels in Groups 3 and 4. Compared to the saline solution irrigation, castor oil extract decreased microorganism counts in root canals immediately after canal preparation. None of the medications used completely eliminated endotoxins in the root canal.

  4. Quality and characteristics of fermented ginseng seed oil based on bacterial strain and extraction method

    Directory of Open Access Journals (Sweden)

    Myung-Hee Lee

    2017-07-01

    Results and Conclusion: The color of the fermented ginseng seed oil did not differ greatly according to the fermentation or extraction method. The highest phenolic compound content recovered with the use of supercritical fluid extraction combined with fermentation using the Bacillus subtilis Korea Food Research Institute (KFRI 1127 strain. The fatty acid composition did not differ greatly according to fermentation strain and extraction method. The phytosterol content of ginseng seed oil fermented with Bacillus subtilis KFRI 1127 and extracted using the supercritical fluid method was highest at 983.58 mg/100 g. Therefore, our results suggested that the ginseng seed oil fermented with Bacillus subtilis KFRI 1127 and extracted using the supercritical fluid method can yield a higher content of bioactive ingredients, such as phenolics, and phytosterols, without impacting the color or fatty acid composition of the product.

  5. Fatty acid composition and antioxidant activity of oils from two cultivars of Cantaloupe extracted by supercritical fluid extraction

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, M.; Mariod, A.; Bagalkotkar, G.; Ling, H. S

    2010-07-01

    The effect of supercritical fluid extraction (SFE) fractionation of three oil fractions (1st, 2nd, 3rd fraction) on the fatty acid composition and antioxidant activity of oils from two cultivars of cantaloupe were investigated. Rock melon oil (RMO) and Golden Langkawi oil (GLO) were extracted using SFE and the major fatty acids for both cultivars were linoleic, oleic, palmitic, and stearic acid. The SFA decreased from 15.78 to 14.14% in RMO 1st fraction, and MUFA decreased from 18.30 to 16.56% in RMO 2nd fraction, while PUFA increased from 65.9 to 69.30% in RMO 3rd fraction. On the other hand SFA decreased from 16.35 to 13.91% in GLO 1{sup s}t fraction, and MUFA decreased from 17.50 to 15.57% in GLO 2nd fraction, while PUFA increased from 66.15 to 70.52% in GLO 3rd fraction. The different fractions of the two oils showed high antioxidant activity in reducing the oxidation of {beta}-carotene in beta-carotene bleaching assay (BCB) and the quenching of 1,1-diphenyl-2-picrylhydrazyl (DPPH). (Author) 41 refs.

  6. Optimization of soxhlet extraction and physicochemical analysis of crop oil from seed kernel of Feun Kase (Thevetia peruviana)

    Science.gov (United States)

    Suwari, Kotta, Herry Z.; Buang, Yohanes

    2017-12-01

    Optimizing the soxhlet extraction of oil from seed kernel of Feun Kase (Thevetia peruviana) for biodiesel production was carried out in this study. The solvent used was petroleum ether and methanol, as well as their combinations. The effect of three factors namely different solvent combinations (polarity), extraction time and extraction temperature were investigated for achieving maximum oil yield. Each experiment was conducted in 250 mL soxhlet apparatus. The physicochemical properties of the oil yield (density, kinematic viscosity, acid value, iodine value, saponification value, and water content) were also analyzed. The optimum conditions were found after 4.5 h with extraction time, extraction temperature at 65 oC and petroleum ether to methanol ratio of 90 : 10 (polarity index 0.6). The oil extract was found to be 51.88 ± 3.18%. These results revealed that the crop oil from seed kernel of Feun Kase (Thevetia peruviana) is a potential feedstock for biodiesel production.

  7. Extraction and Separation of Volatile and Fixed Oils from Berries of Laurus nobilis L. by Supercritical CO2

    Directory of Open Access Journals (Sweden)

    M. Assunta Dessì

    2008-08-01

    Full Text Available Isolation of volatile and fixed oils from dried berries of Laurus nobilis L. from Tunisia have been obtained by supercritical fractioned extraction with carbon dioxide. Extraction experiments were carried out at a temperature of 40 °C and pressures of 90 and 250 bar. The extraction step performed at 90 bar produced a volatile fraction mainly composed of (E-β-ocimene (20.9%, 1,8-cineole (8.8%, α-pinene (8.0%, β-longipinene (7.1%, linalool acetate (4.5%, cadinene (4.7%, β-pinene (4.2%, α-terpinyl acetate (3.8% and α-bulnesene (3.5%. The oil yield in this step of the process was 0.9 % by weight charged. The last extraction step at 250 bar produced an odorless liquid fraction, in which a very small percentage of fragrance compounds was found, whereas triacylglycerols were dominant. The yield of this step was 15.0 % by weight. The most represented fatty acids of the whole berry fixed oil were 12:0 (27.6%, 18:1 n-9 (27.1%, 18:2 n-6 (21.4%, and 16:0 (17,1%, with the 18:1 n-9 and 18:2 n-6 unsaturated fatty acids in particular averaging 329 μg/mg of oil.

  8. Integrated oil production and upgrading using molten alkali metal

    Science.gov (United States)

    Gordon, John Howard

    2016-10-04

    A method that combines the oil retorting process (or other process needed to obtain/extract heavy oil or bitumen) with the process for upgrading these materials using sodium or other alkali metals. Specifically, the shale gas or other gases that are obtained from the retorting/extraction process may be introduced into the upgrading reactor and used to upgrade the oil feedstock. Also, the solid materials obtained from the reactor may be used as a fuel source, thereby providing the heat necessary for the retorting/extraction process. Other forms of integration are also disclosed.

  9. Mackerel (Scomber Scrombrus Oil Extraction and Evaluation as Raw Materials for Industrial Utilization

    Directory of Open Access Journals (Sweden)

    A. A. BAWA

    2006-01-01

    Full Text Available The extraction, evaluation and refining of fish oil from mackerel (scomber scrombrus has been conducted in this work. The total percentage oil yield using solvent extraction and total moisture content was 28.24% and 56.50 %respectively, which were found to increase linearly with time. The analytical properties of the crude and the refined oil were evaluated. It was observed that the crude oil consist from: acid value 2.5 mg/KOH, peroxide value 2.19 mEq/kg, saponification value 201.6 mgKOH/g, iodine value 108.09 I2/100g, specific gravity 0.911, refractive index 1.485 and reddish brown colour. The refined oil was also evaluated as follows: acid value 2.27 mg/KOH, peroxide 1.00 meq/kg, saponification value 147.84 mgKOH/g, iodine value 106.93 I2 /100g and golden brown colour. These values fall within the acceptable standard values. The refining of the oil brought about a notable improvement in the analytical properties of the oil. Thus, leads to a high quality fish oil in terms of the taste, colour, odours, shelf life and market value. Based on the improved characteristics of the oil, it could be suitable for applications in pharmaceutical and food industries.

  10. Process water treatment in Canada's oil sands industry : 2 : a review of emerging technologies

    International Nuclear Information System (INIS)

    Allen, E.W.

    2008-01-01

    This review was conducted to identify candidate treatment technologies for treating oil sands process water. The oil sands industry in Canada uses large volumes of fresh water in order to extract bitumen deposits. The development of process water treatment technologies has become a critical issue for the industry, particularly as oil sand production is expected to triple in the next decade. However, treatment technologies must be adapted to consider the fouling potential of bitumens and fine clays as well as the effect of alkaline process water on treatment performance. The review included developments in chemical modifications to membranes and adsorbents designed to improve pollutant removal and reduce fouling; hybridization technologies designed to enhance the biological treatment of toxic feedwaters; recent advances in photocatalytic oxidation technologies for organic compounds; and new designs for large-scale treatment wetlands for polluted waste waters. It was concluded that major knowledge gaps must be optimized and preliminary studies must be conducted in order to understand how the treatment technologies will be affected by the chemical and physical characteristics of oil sands process water. 188 refs., 8 tabs

  11. development of a motorized kneader for groundnut oil extraction

    African Journals Online (AJOL)

    Dr Obe

    The machine was constructed, and evaluated for its performance in terms of, its kneading time and ... groundnut oil extraction is a profitable business, and mosly done by women. It was also .... (2.0 hp) single-phase electric motor and its small.

  12. Supercritical Fluid Extraction of Seed Oil from Chinese Licorice ...

    African Journals Online (AJOL)

    CO2) extraction. The oil was analysed by GC-MS after methylation. Compounds were identified according to their mass spectra (EI, 70 eV) by comparison with authentic reference substances and literature data. Five fatty acids were identified, with ...

  13. THE CHARACTERISTICS OF THE PRODUCTION AND PROCESSING OF OIL AND NATURAL GAS IN CROATIA FROM 2000 TO 2014

    Directory of Open Access Journals (Sweden)

    Josipa Velić

    2016-06-01

    Full Text Available This research analyzes the characteristics of the production and processing of oil, condensates and natural gas in the Republic of Croatia starting from 2000, until the end of 2014. Amounts of balance sheet (exploitable reserves of oil and condensates ranges from 9330,92 × 103 m3 in 2005, to 13 471,08 × 103 m3 in 2013, while extracted amounts are gradually declining from 1332,61 × 103 m3 to 639,96 × 103 m3. The ratio of extracted amounts and reserves is gradually declining, meaning that a slight increase in reserves does not affect the extracted amounts. Exploitable reserves of natural gas during the observed period fluctuate greatly. Being peaked in 2007, at 40,919.70 × 106 m3, they reached a low in 2014, at 17,932.98 × 106 m3. Unlike liquid hydrocarbons, the ratio of extracted and exploitable amounts is growing and peaked in 2014. Overall energy demands for oil in Croatia (shown as total consumption of crude oil amounted to 3032,8 × 103 m3 in 2013, while demands for natural gas amounted to 2809,90 × 106 m3. It is interesting to note that the consumption of oil is rapidly declining, which is a favorable trend from the standpoint of reducing emissions of greenhouse gases. While needs are partly covered by domestic exploitation, the dependence on imports of oil and natural gas is still evident and ranges from 75% to 84% for oil and 28% to 46% for natural gas, without major changes to the trend. The amounts of processed hydrocarbons are declining gradually, especially motor gasoline and fuel oil, while diesel fuel amounts remain mostly the same. Further research as well as development of the exploitation of oil and natural gas is of paramount importance, especially by investing in cadre education and new technologies.

  14. Process of deparaffining oils

    Energy Technology Data Exchange (ETDEWEB)

    1941-03-05

    This process comprises centrifuging in the presence of a solvent which dissolves the oil and precipitates the paraffins, with the addition of an auxiliary liquid whose surface tension with respect to the oil solution does not exceed 50 dynes/cm.

  15. The numerical simulation on swelling factor and extraction rate of a tight crude oil and SC-CO2 system

    Science.gov (United States)

    Zou, Hongjun; Gong, Houjian; Li, Yajun; Dong, Mingzhe

    2018-03-01

    A method was established to study swelling and extraction between CO2 and crude oil, and the influences of pressure, temperature and molecular weight were investigated. Firstly, laboratory analysis was conducted to determine the pseudo-component and other parameters of the crude oil. Then swelling and extraction of the crude oil and SC-CO2 system were calculated by computer simulation. The results show that the pressure and temperature have little influence on the swelling and extraction between CO2 and crude oil when the mole fraction of CO2 is lower. A higher pressure and temperature is more beneficial to the interaction of CO2 and crude oil, while the swelling and extraction will not be obvious when the system is miscible. And the smaller the molecular weight of the oil is, the larger the maximum value of the swelling factor of CO2 and crude oil changes. The study of swelling and extraction plays an important role in the oilfield stimulation.

  16. Experimental results for the extraction of essential oil from Lippia sidoides cham. using pressurized carbon dioxide

    Directory of Open Access Journals (Sweden)

    Sousa EMBD.

    2002-01-01

    Full Text Available The odoriferous species Lippia sidoides Cham. is abundant in the Brazilian Northeast. Its essential oil possesses antiseptic activity due to the presence of thymol. In this work, thermodynamic and kinetic data were experimentally determined for the CO2 + L. sidoides system. Solubility was determined using the dynamic method at pressures of 66.7 and 78.5 bar and temperatures of 283.15, 288.15, 293.15, 295.15, and 298.15 K. SFE kinetic data were obtained at 288.15 K and 66.7 bar. The composition of the multicomponent solute mixture was determined by GC-MS and compared to the composition of both the volatile oil obtained by steam distillation and the oleoresin obtained using ethanol. The SFE process yield was higher than the yield of either the steam distillation or the ethanol extraction. The solubilities were correlated using the Peng-Robinson equation of state with one binary interaction parameter for the attractive term, considering the essential oil as a pseudo-component. Sovová?s model quantitatively described the overall extraction curve.

  17. Aqueous Extract Composition of Spent Ginger (Zingiber officinale var. Amarum) from Essential Oil Distillation

    Science.gov (United States)

    Manuhara, G. J.; Mentari, G. P.; Khasanah, L. U.; Utami, R.

    2018-03-01

    Ginger (Zingiber officinale var Amarum) is widely used as raw material for essential oil production in Indonesia and contain high functional compounds. After producing essential oil, distillation leave less valuable spent ginger. This research was conducted to determine the bioactive compounds remained in aqueous extract of the spent ginger. The extracts were produced at various combination of temperature (55, 75, 95°C) and duration (15, 30, 45 minutes). The extract composition was observed using Gas Chromatography - Mass Spectrometry analysis. The temperature and time of maceration extraction affected the content of compounds in spent ginger aqueous extracts. The extracts contained four largest components of α-curcumene, α-zingiberene, β-sesquiphellandrene and β-bisabolene. The aqueous extracts from spent ginger contained the compounds which may contribute to distinctive flavor of ginger and also bioactive function.

  18. The Effectiveness of Rambutan (Nephelium lappaceum L.) Extract in Stabilization of Sunflower Oil under Accelerated Conditions

    Science.gov (United States)

    Mei, Winne Sia Chiaw; Ismail, Amin; Mohd. Esa, Norhaizan; Akowuah, Gabriel Akyirem; Wai, Ho Chun; Seng, Yim Hip

    2014-01-01

    The oxidative properties of sunflower oil supplemented with rambutan extract, (crude extract and its fractionated fraction, SF II) in comparison with synthetic antioxidant were investigated. The supplemented sunflower oils were stored under accelerated conditions for 24 days at 60 °C. For every 6-day interval, the oxidative properties of the supplemented sunflower oil were evaluated based on the following tests, namely peroxide value, p-anisidine value, Thiobarbituric Acid Reactive Substances (TBARS) assay, iodine value and free fatty acids. The total oxidation (TOTOX) values were also calculated based on the peroxide values and p-anisidine values. Rambutan extract is a potential source of antioxidant. The oxidative activities of the extracts at all concentrations were significantly (p crude extract. With a 2-year storage period at ambient temperature, the fractionated fraction of the extract, SF II at 300 ppm, was observed to work more effectively than the synthetic antioxidant, t-Tocopherol, and it possessed a protective effect comparable with butylatedhydrioxynanisole (BHA). Therefore, rambutan extract could be used as a potential alternative source of antioxidant in the oil industry or other fat-based products to delay lipid oxidation. PMID:26784877

  19. An EPR measure of phenolic content in various wine grapeseeds from marc and grapeseed meals left after oil extraction

    International Nuclear Information System (INIS)

    Jordan, R.

    2002-01-01

    Full text: Marc is the leftover material (skins, pulp, seeds, stems) from the fermentation mainly of red wines. Owing to the increase in Australian wine production for home and export, and the decrease in Spirits consumption, marc could be in surfeit- Marc seeds for example, still contain oil and tannins which are useful products. So the titular study by EPR was undertaken. Grapeseeds of various varieties were collected on the vine, and from marc after fermentation. The meal remaining from marc seeds after oil extraction was also collected, and climate was taken into account. From this very limited trial, there appears to be no obvious effect of climate on phenolic content. In most cases, the phenolic content of grapeseeds post-winemaking is lower than that pre-winemaking, consistent with the winemaking process significantly affecting phenolic content. For grapeseed meal, in most cases the phenolic content is lower than that of the seeds used to produce the meal. This 'negative' effect of the oil extraction process is consistent with our previously unpublished work (commercial - in - confidence), but is not necessarily economically significant

  20. Uranium extraction process in a sulfuric medium by means of liquid emulsified membranes

    International Nuclear Information System (INIS)

    Monteillet, A.

    1985-02-01

    Uranium ore processing, after leaching by sulfuric acid, by liquid-liquid extraction is a rather heavy process, not suitable for small deposits. Extraction by emulsions was suggested. In this process the leachate is contacted with an oil in water type emulsion, a liquid organic membrane is formed by the continuous phase. Uranium complexes diffuse through the liquid membrane towards the dispersed aqueous phase of the emulsion (stripping solution). Uranium is recovered by breaking the emulsion. Are successively studied: development of stable emulsions, influence of emulsion composition on uranium transfer kinetics, transfer mechanisms through the membrane and modelling of kinetics data obtained in the experimental study [fr

  1. Extraction of interesting organic compounds from olive oil waste

    Directory of Open Access Journals (Sweden)

    Jiménez, Ana

    2006-03-01

    Full Text Available In the olive fruits there is a large amount of bioactive compounds and substances of high interest. Many of them are known by owing health beneficial properties that contribute to protective effect of the virgin olive oil. During olive oil processing, most of them remain in the olive oil wastes. Although, olive-mill wastewater (OMWW or “alpechin”, olive oil cake (OOC, and the new by-product, known as “alperujo” in Spain and generated by the two-phase extraction process, represent a major disposal and potentially severe pollution problem for the industry, they are also promising source of substances of high value. This review summarises the last knowledge on the utilisation of residual products, with more than 90 references including articles and patents, which are promising with regard to future application. All these investigations have been classified into two options, the recovery of valuable natural constituents and the bioconversion into useful products.Existe una gran cantidad de compuestos bioactivos y de alto interés presentes en la aceituna. Muchos de ellos se conocen por las cualidades beneficiosas que aportan al aceite de oliva virgen. La mayoría permanecen en mayor cantidad en el subproducto de la extracción del aceite. Aunque, el alpechín, el orujo y el nuevo subproducto de extracción del aceite en dos fases, alperujo, representan un problema potencial de vertido y contaminación, también son una prometedora fuente de compuestos de alto valor. Esta revisión resume lo último que se conoce sobre la utilización de estos residuos en el campo anteriormente mencionado, con más de 90 referencias que incluyen artículos y patentes. Todas estas investigaciones han sido clasificadas en cuanto a la recuperación de constituyentes naturalmente presentes o en cuanto a la bioconversión de los residuos en sustancias de interés.

  2. Influence sample sizing of citrus hystrix essential oil from hydrodistillation extraction

    Science.gov (United States)

    Yahya, A.; Amadi, I.; Hashib, S. A.; Mustapha, F. A.

    2018-03-01

    Essential oil extracted from kaffir lime leaves through hydrodistillation. The objective of this study is to quantify the oil production rate by identify the significant influence of particle size on kaffir lime leaves. Kaffir lime leaves were ground and separated by using siever into 90, 150, 300 μm and other kaffir lime leaves. The mean essential oil yield of 0.87, 0.52, 0.41 and 0.3% was obtained. 90 μm of ground gives the highest yield compared to other sizes. Thus, it can be concluded that in quantifying oil production rate, the relevance of different size of particle is clearly affects the amount of oil yield. In analysing the composition of kaffir lime essential oil using GC-MS, there were 38 compounds found in the essential oil. Some of the major compounds of the kaffir lime leave oils were detected while some are not, may due to oil experience thermal degradation which consequently losing some significant compounds in controlled temperature.

  3. Fractionation of lemon essential oil by solvent extraction: Phase equilibrium for model systems at T = 298.2 K

    International Nuclear Information System (INIS)

    Koshima, Cristina C.; Capellini, Maria C.; Geremias, Ivana M.; Aracava, Keila K.; Gonçalves, Cintia B.; Rodrigues, Christianne E.C.

    2012-01-01

    Highlights: ► Deterpenation of lemon oil by solvent extraction using hydrous ethanol. ► Limonene, γ-terpinene, β-pinene, and citral were used to simulate the oil. ► Citral shows a higher distribution coefficient than the hydrocarbons. ► Terpenic hydrocarbons exhibit very similar phase separation behaviour. ► NRTL and UNIQUAC models provided a good description of the phase equilibrium. - Abstract: The fractioning of lemon essential oil can be performed by liquid–liquid extraction using hydrous ethanol as a solvent. A quaternary mixture composed of limonene, γ-terpinene, β-pinene, and citral was used to simulate lemon essential oil. In this paper, we present (liquid + liquid) equilibrium data that were experimentally determined for systems containing essential oil compounds, ethanol, and water at T = 298.2 K. The experimental data were correlated using the NRTL and UNIQUAC models, and the mean deviations between calculated and experimental data were less than 0.0053 in all systems, indicating the accuracy of these molecular models in describing our systems. The results show that as the water content in the solvent phase increased, the values of the distribution coefficients decreased, regardless of the type of compound studied. However, the oxygenated compound always showed the highest distribution coefficient among the components of the essential oil, thus making deterpenation of the lemon essential oil a feasible process.

  4. Pumpkin Seed Oil Extracted From Cucurbita maxima Improves Urinary Disorder in Human Overactive Bladder

    Directory of Open Access Journals (Sweden)

    Mie Nishimura

    2014-01-01

    Full Text Available The pumpkin seed oil obtained from Cucurbita pepo has been shown to be useful for the treatment of nocturia in patients with urinal disorders in several western countries. In this study, we evaluated the effect of the pumpkin seed oil from Cucurbita maxima on urinary dysfunction in human overactive bladder (OAB. Forty-five subjects were enrolled in this study. An extract of pumpkin seed oil from C. maxima (10 g of oil/day was orally administrated for 12 weeks. After 6 and 12 weeks, urinary function was evaluated using Overactive Bladder Symptom Score (OABSS. Pumpkin seed oil from C. maxima significantly reduced the degree of OABSS in the subjects. The results from our study suggest that pumpkin seed oil extracts from C. maxima as well as from C. pepo are effective for urinary disorders such as OAB in humans.

  5. Antioxidant activity and sensory analysis of murtilla (Ugni molinae Turcz. fruit extracts in an oil model system

    Directory of Open Access Journals (Sweden)

    T. R. Augusto-Obara

    2017-03-01

    Full Text Available An oil model system was used to analyze the antioxidant activity of Chilean fruit extracts and to determine their odor sensory effect. Hydroalcoholic extracts from wild and 14-4 genotype murtilla (Ugni molinae Turcz. fruit were assessed by the Response Surface Methodology. The optimal conditions for producing high total phenolic-content extracts were 49.5% (v/v ethanol at 30 ºC, which yielded 18.39 and 26.14 mg GAE·g-1 dry matter, respectively. The optimized extracts were added to a lipid model system and evaluated via the Schaal Oven Test. After 96 hours, 150 and 200 mg·kg-1 oil of the wild and 14-4 genotype extracts, respectively, showed an antioxidant capacity similar to TBHQ (200 mg·kg-1 oil in terms of peroxide values and odor. Thus, murtilla fruit extracts are a natural source of antioxidants for protecting lipidic foods, such as soybean oil.

  6. Antioxidant activity and sensory analysis of murtilla (Ugni molinae Turcz.) fruit extracts in an oil model system

    International Nuclear Information System (INIS)

    Augusto-Obara, T.R.; Pirce, F.; Scheuermann, E.; Spoto, M.H.F.; Vieira, T.M.F.S.

    2017-01-01

    An oil model system was used to analyze the antioxidant activity of Chilean fruit extracts and to determine their odor sensory effect. Hydroalcoholic extracts from wild and 14-4 genotype murtilla (Ugni molinae Turcz.) fruit were assessed by the Response Surface Methodology. The optimal conditions for producing high total phenolic-content extracts were 49.5% (v/v) ethanol at 30 ºC, which yielded 18.39 and 26.14 mg GAE·g−1 dry matter, respectively. The optimized extracts were added to a lipid model system and evaluated via the Schaal Oven Test. After 96 hours, 150 and 200 mg·kg−1 oil of the wild and 14-4 genotype extracts, respectively, showed an antioxidant capacity similar to TBHQ (200 mg·kg−1 oil) in terms of peroxide values and odor. Thus, murtilla fruit extracts are a natural source of antioxidants for protecting lipidic foods, such as soybean oil. [es

  7. Kinetics of hydrocarbon extraction from oil shale using biosurfactant producing bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Haddadin, Malik S.Y.; Abou Arqoub, Ansam A.; Abu Reesh, Ibrahim [Faculty of Graduate Studies, Jordan University, Queen Rania Street, Amman, 11942 (Jordan); Haddadin, Jamal [Faculty of Agriculture, Mutah University, P.O. Box 59, Mutah 61710 (Jordan)

    2009-04-15

    This study was done to extract hydrocarbon compounds from El-Lajjun oil shale using biosurfactant produced from two strains Rhodococcus erythropolis and Rhodococcus ruber. The results have shown that, optimal biosurfactant production was found using naphthalene and diesel as a carbon source for R. erthropolis and R. ruber, respectively. Optimum nitrogen concentration was 9 g/l and 7 g/l for R. erthropolis and R. ruber, respectively. Optimum K{sub 2}HPO{sub 4} to KH{sub 2}PO{sub 4} ratio, temperature, pH, and agitation speeds were 2:1, 37 C, 7 and 200 rpm. Under optimal conditions R. erthropolis and R. ruber produced 5.67 and 6.9 g/l biosurfactant, respectively. Maximum recovery of oil achieved with hydrogen peroxide pre-treatment was 25% and 26% at biosurfactant concentration of 8 g/l and 4 g/l for R. erthropolis and R. ruber, respectively. The extent desorption of hydrocarbons from the pre-treated oil shale by biosurfactant were inversely related to the concentration of high molecular weight hydrocarbons, asphaltenes compounds. Pre-treatment of oil shale with hydrogen peroxide produced better improvement in aromatic compounds extraction in comparison with improvement which resulted from demineralization of the oil shale. (author)

  8. Supercritical carbon dioxide extraction of oil from Clanis bilineata ...

    African Journals Online (AJOL)

    AJL

    2012-02-16

    Feb 16, 2012 ... temperature, 35°C; pressure, 25 MPa; supercritical CO2 flow rate, 20 L/min and time, 60 min. ... methyl esters were recovered after solvent evaporation in vacuum ... Effect of time on extraction of the oil from C. bilineata larvae.

  9. Antioxidant Effects of Grape Vine Cane Extracts from Different Chinese Grape Varieties on Edible Oils

    OpenAIRE

    Min, Zhuo; Guo, Zemei; Wang, Kai; Zhang, Ang; Li, Hua; Fang, Yulin

    2014-01-01

    This study involved the determination of the peroxide value (POV) as a measure of the resistance of the oxidation of edible oil with grape vine cane additives to assess their antioxidation potential. The study demonstrated that grape extracts of canes could effectively inhibit the lipid oxidation of edible oils and that this ability varied significantly due to the different extraction solvents employed, as well as to the different varieties of canes used. Lipid oxidation of edible oils was si...

  10. Electronic techniques for subsea oil exploration and extraction

    Energy Technology Data Exchange (ETDEWEB)

    1976-01-01

    Subsea oil exploration and extraction is becoming increasingly difficult, costly, and dangerous. Electronics is contributing to make offshore work easier and safer. It is used for positioning ships or oil rigs, for remotely controlling well-heads and tool reentry operations, for pipelaying operations, and for monitoring underwater equipment. It is also tending to replace men in diving operations. The specific achievements of THOMPSON--CSF in this field are described. Fully automated operation of the winches on the ETPM 1601 barge proved successful during a recent pipelaying operation. The technique used by THOMPSON--CSF in this venture allowed a single operator to control all the maneuvers. These are briefly described. (MCW)

  11. Effect of commercial processing procedures on 14C-LINDANE residues in corn oil

    International Nuclear Information System (INIS)

    Soliman, S.M.

    2006-01-01

    At blooming, maize plants were sprayed twice, 23 days apart, at a dose of 22 mg equivalent to 5 μCi/ plant. At post harvest, maize seeds had a radioactivity corresponding to 0.36% of the applied dose. The insecticide residues in crude oil, cake and methanolic extract were amounted to 8 % and 60 % 5 % , respectively, of original residues inside the seeds.The 14 C-activity in the crude oil could be reduced by commercial processes locally used for refining. The refined oil had a residue level of about 0.7 ppm mainly in the form of unchanged lindane in addition to a number of chloro phenols as main metabolites. Refining of corn oil fortified with 14 C-lindane led to a high reduction of 14 C-lindane (88%). The refined oil contained a residue consisting lindane and its chloro phenols

  12. Optimization of supercritical carbon dioxide extraction of Piper Betel Linn leaves oil and total phenolic content

    Science.gov (United States)

    Aziz, A. H. A.; Yunus, M. A. C.; Arsad, N. H.; Lee, N. Y.; Idham, Z.; Razak, A. Q. A.

    2016-11-01

    Supercritical Carbon Dioxide (SC-CO2) Extraction was applied to extract piper betel linn leaves. The piper betel leaves oil was used antioxidant, anti-diabetic, anticancer and antistroke. The aim of this study was to optimize the conditions of pressure, temperature and flowrate for oil yield and total phenolic content. The operational conditions of SC-CO2 studied were pressure (10, 20, 30 MPa), temperature (40, 60, 80 °C) and flowrate carbon dioxide (4, 6, 8 mL/min). The constant parameters were average particle size and extraction regime, 355pm and 3.5 hours respectively. First order polynomial expression was used to express the extracted oil while second order polynomial expression was used to express the total phenolic content and the both results were satisfactory. The best conditions to maximize the total extraction oil yields and total phenolic content were 30 MPa, 80 °C and 4.42 mL/min leading to 7.32% of oil and 29.72 MPa, 67.53 °C and 7.98 mL/min leading to 845.085 mg GAE/g sample. In terms of optimum condition with high extraction yield and high total phenolic content in the extracts, the best operating conditions were 30 MPa, 78 °C and 8 mL/min with 7.05% yield and 791.709 mg gallic acid equivalent (GAE)/g sample. The most dominant condition for extraction of oil yield and phenolic content were pressure and CO2 flowrate. The results show a good fit to the proposed model and the optimal conditions obtained were within the experimental range with the value of R2 was 96.13% for percentage yield and 98.52% for total phenolic content.

  13. Inhibitory Effects of Pterodon emarginatus Bean Oil and Extract on Staphylococcus aureus.

    Science.gov (United States)

    Mendes, V S; Sant'Anna, J B; Oliveira, S C C; Maldonade, Iriani Rodrigues; Machado, Eleuza Rodrigues

    2017-01-01

    Pterodon emarginatus is a tree of the Brazilian Savannah. The beans of this tree are used in folk medicine as anti-inflammatory preparations, especially for infections caused by Staphylococcus aureus . These bacteria can cause simple infections or serious illnesses such as pneumonia, meningitis, endocarditis, toxic shock syndrome, septicemia, and others. This study had the goal of verifying the effect of the essential oil (OE) from P. emarginatus on the inhibition of S. aureus in culture medium, i.e., " in vitro " tests. The vegetable material was cut and crushed with a press. The OE was obtained by extraction using hexane, alcohol, and water. The P. emarginatus extracts obtained were used to evaluate the antimicrobial effect on S. aureus (ATCC 25923) by tests of well diffusion, disc diffusion, and microdilution. The strain used in the assays was maintained in brain heart infusion broth and nutrient agar until testing. Afterward, the bacteria were spread on agar plates with Mueller-Hinton agar medium. In the wells and on the paper discs, the OE suspensions were placed in the following volumes: 10, 15, 20, 25, 30, 40, and 80 μL and subsequently they were incubated at 35°C ± 2°C. After 24 h, the number of colony-forming unit was determined. Pure OE and hydroalcoholic extract inhibited the growth of S. aureus , while aqueous extract had no effect on bacterial growth in all microbial methods used. Thus, the present study showed the potential of sucupira-based extracts against S. aureus growth, opening new perspectives for the evaluation of these bioactive compounds as phytopharmaceutical products. Plant extract act as antimicrobials to prevent and reduce bacterial contaminationBeans of Pterodon emarginatus has antibacterial propertiesExtraction with different solvents might implicate on the rate of bacterial deathThe effect of different microbiological methods (well diffusion, disc diffusion and microdilution) was evaluated on reducing CFUThe results showed by MBC

  14. Microwave-assisted extraction of green coffee oil and quantification of diterpenes by HPLC.

    Science.gov (United States)

    Tsukui, A; Santos Júnior, H M; Oigman, S S; de Souza, R O M A; Bizzo, H R; Rezende, C M

    2014-12-01

    The microwave-assisted extraction (MAE) of 13 different green coffee beans (Coffea arabica L.) was compared to Soxhlet extraction for oil obtention. The full factorial design applied to the microwave-assisted extraction (MAE), related to time and temperature parameters, allowed to develop a powerful fast and smooth methodology (10 min at 45°C) compared to a 4h Soxhlet extraction. The quantification of cafestol and kahweol diterpenes present in the coffee oil was monitored by HPLC/UV and showed satisfactory linearity (R(2)=0.9979), precision (CV 3.7%), recovery (yield calculated on the diterpenes content for sample AT1 (Arabica green coffee) showed a six times higher value compared to the traditional Soxhlet method. Copyright © 2014 Elsevier Ltd. All rights reserved.

  15. TBP determination in nitric acid solutions from solvent extraction process

    International Nuclear Information System (INIS)

    Kuada, T.A.; Carvalho, E.I. de; Araujo, I. da C.; Cohen, V.H.

    1988-07-01

    Heavy organic phases have been observed on some occasions during TBP extraction process. These products, described as red oils, were considered as the main cause for process failures, specially in evaporators and concentrators. In view of safety aspects it is necessary to control organic concentration in product and waste solutions. The proposed method involves the organic removal by chloroform as a first step, followed by purification onto a silica gel column. The results are given from analysing TBP and its degradation product (DBP) by gas chromatography. (author) [pt

  16. The loss of essential oil components induced by the Purge Time in the Pressurized Liquid Extraction (PLE) procedure of Cupressus sempervirens.

    Science.gov (United States)

    Dawidowicz, Andrzej L; Czapczyńska, Natalia B; Wianowska, Dorota

    2012-05-30

    The influence of different Purge Times on the effectiveness of Pressurized Liquid Extraction (PLE) of volatile oil components from cypress plant matrix (Cupressus sempervirens) was investigated, applying solvents of diverse extraction efficiencies. The obtained results show the decrease of the mass yields of essential oil components as a result of increased Purge Time. The loss of extracted components depends on the extrahent type - the greatest mass yield loss occurred in the case of non-polar solvents, whereas the smallest was found in polar extracts. Comparisons of the PLE method with Sea Sand Disruption Method (SSDM), Matrix Solid-Phase Dispersion Method (MSPD) and Steam Distillation (SD) were performed to assess the method's accuracy. Independent of the solvent and Purge Time applied in the PLE process, the total mass yield was lower than the one obtained for simple, short and relatively cheap low-temperature matrix disruption procedures - MSPD and SSDM. Thus, in the case of volatile oils analysis, the application of these methods is advisable. Copyright © 2012 Elsevier B.V. All rights reserved.

  17. Grinding and cooking dry-mill germ to optimize aqueous enzymatic oil extraction

    Science.gov (United States)

    The many recent dry grind plants that convert corn to ethanol are potential sources of substantial amounts of corn oil. This report describes an aqueous enzymatic extraction (AEE) method to separate oil from dry-mill corn germ (DMG). The method is an extension of AEE previously developed for wet...

  18. Experimental determination of hydrogen content of oil extract from jatropha seeds

    International Nuclear Information System (INIS)

    Okunade, I.O.; Jonah, S.A.; Omede, M.O.

    2010-01-01

    The thermal neutron technique was used for the determination of hydrogen content of oil extract from Jatropha seeds. The experimental arrangement consists of a source holder, Am-Be neutron source embedded in paraffin wax and 3 He detector was used to measure reflection coefficient as a function of hydrogen content of various hydrocarbon materials used as calibration standards. The hydrogen content which is an important property of fuel oils was determined for jatropha oil and jatropha-synthetic diesel using their measured values of neutron reflection coefficients and calibration data. The result obtained showed that the hydrogen content of Jatropha oil exceeds that of the synthetic diesel, thus indicating its suitability as a fuel oil for powering diesel engines. The results obtained also indicated that hydrogen content of jatropha-synthetic diesel mixture increases as the volumetric concentration of jatropha oil in the mixture increases, indicating that jatropha oil can serve as a suitable additive to synthetic diesel oil.

  19. Cytotoxicity and effect of extraction methods on the chemical composition of essential oils of Moringa oleifera seeds

    Science.gov (United States)

    Kayode, Rowland Monday Ojo; Afolayan, Anthony Jide

    2015-01-01

    Renewed interest in natural materials as food flavors and preservatives has led to the search for suitable essential oils. Moringa oleifera seed essential oil was extracted by solvent-free microwave and hydrodistillation. This study assessed its chemical constituents. Cytotoxicity of the oils was investigated using hatchability and lethality tests on brine shrimps. A total of 16 and 26 compounds were isolated from the hydrodistillation extraction (HDE) and solvent-free microwave extraction (SME) oils, respectively, which accounted for 97.515% and 97.816% of total identifiable constituents, respectively. At 24 h when the most eggs had hatched, values of the SME (56.7%) and HDE (60.0%) oils were significantly different (P1000 mg/ml recommended as an index for non-toxicity, which gives the oil advantage over some antioxidant, antimicrobial, therapeutic, and preservative chemicals. PMID:26238543

  20. Rapid magnetic solid-phase extraction based on monodisperse magnetic single-crystal ferrite nanoparticles for the determination of free fatty acid content in edible oils.

    Science.gov (United States)

    Wei, Fang; Zhao, Qin; Lv, Xin; Dong, Xu-Yan; Feng, Yu-Qi; Chen, Hong

    2013-01-09

    This study proposes a rapid magnetic solid-phase extraction (MSPE) based on monodisperse magnetic single-crystal ferrite (Fe(3)O(4)) nanoparticles (NPs) for determining the quantities of eight free fatty acids (FFAs), including palmitic acid (C16:0), stearic acid (C18:0), oleic acid (C18:1), linoleic acid (C18:2), linolenic acid (C18:3), arachidic acid (C20:0), eicosenoic acid (C20:1), and behenic acid (C22:0) in oil. The amine-functionalized mesoporous Fe(3)O(4) magnetic NPs were applied as a sorbent for MSPE of FFAs from oil samples in a process that is based on hydrophilic interaction. The extraction can be completed rapidly in a dispersive mode with the aid of vigorous vortex. Additional tedious processing steps such as centrifugation and evaporation of organic solvent were not necessary with this procedure. Furthermore, esterification of FFAs can be accomplished during the desorption procedure by using methanol/sulfuric acid (99:1, v/v) as the desorption solvent. Several parameters affecting the extraction efficiency were investigated, including the matrix solvent for extraction, the desorption solvent and desorption time, and the amount of sorbent and extraction time. The pretreatment process was rapid under optimal conditions, being accomplished within 15 min. When coupled with gas chromatography-flame ionization detection (GC-FID), a rapid, simple, and convenient MSPE-GC-FID method for the determination of FFAs in oil samples was established with a total analysis time within 25 min. The limits of detection for the target FFAs were found to be 7.22-26.26 ng/mL. Recoveries in oil samples were in the range of 81.33-117.75%, with RSDs of <6.4% (intraday) and <6.9% (interday). This method was applied successfully to the analysis of dynamic FFA formation in four types of edible oils subjected to an accelerated storage test. The simple, rapid, and cost-effective method developed in the current study offers a potential application for the extraction and

  1. 21 CFR 182.50 - Certain other spices, seasonings, essential oils, oleoresins, and natural extracts.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Certain other spices, seasonings, essential oils... GENERALLY RECOGNIZED AS SAFE General Provisions § 182.50 Certain other spices, seasonings, essential oils, oleoresins, and natural extracts. Certain other spices, seasonings, essential oils, oleoresins, and natural...

  2. 21 CFR 582.50 - Certain other spices, seasonings, essential oils, oleoresins, and natural extracts.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Certain other spices, seasonings, essential oils... GENERALLY RECOGNIZED AS SAFE General Provisions § 582.50 Certain other spices, seasonings, essential oils, oleoresins, and natural extracts. Certain other spices, seasonings, essential oils, oleoresins, and natural...

  3. BP and NCB to collaborate in coal liquefaction study. [Supercritical gas extraction; dissolution in anthracene oil

    Energy Technology Data Exchange (ETDEWEB)

    1978-02-17

    British Petroleum and NCB are collaborating in a two year study of coal liquefaction which could result in a demonstration plant being built. The two liquefaction techniques which the NCB is developing at present are supercritical extraction, and dissolution in anthracene oil. A disadvantage of the latter process is that high grade coking coals must be used.

  4. Fast and effective low-temperature freezing extraction technique to determine organotin compounds in edible vegetable oil.

    Science.gov (United States)

    Liu, Yingxia; Ma, Yaqian; Wan, Yiqun; Guo, Lan; Wan, Xiaofen

    2016-06-01

    Most organotin compounds that have been widely used in food packaging materials and production process show serious toxicity effects to human health. In this study, a simple and low-cost method based on high-performance liquid chromatography with inductively coupled plasma mass spectrometry for the simultaneous determination of four organotins in edible vegetable oil samples was developed. Four organotins including dibutyltin dichloride, tributyltin chloride, diphenyltin dichloride, and triphenyltin chloride were simultaneously extracted with methanol using the low-temperature precipitation process. After being concentrated, the extracts were purified by matrix solid-phase dispersion using graphitized carbon black. The experimental parameters such as extraction solvent and clean-up material were optimized. To evaluate the accuracy of the new method, the recoveries were investigated. In addition, a liquid chromatography with tandem mass spectrometry method was also proposed for comparison. The procedures of extracting and purifying samples for the analysis were simple and easy to perform batch operations, also showed good efficiency with lower relative standard deviation. The limits of detection of the four organotins were 0.28-0.59 μg/L, and the limits of quantification of the four organotins were 0.93-1.8 μg/L, respectively. The proposed method was successfully applied to the simultaneous analysis of the four organotins in edible vegetable oil. Some analytes were detected at the level of 2.5-28.8 μg/kg. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  5. Adsorption of acid-extractable organics from oil sands process-affected water onto biomass-based biochar: Metal content matters.

    Science.gov (United States)

    Bhuiyan, Tazul I; Tak, Jin K; Sessarego, Sebastian; Harfield, Don; Hill, Josephine M

    2017-02-01

    The impact of biochar properties on acid-extractable organics (AEO) adsorption from oil sands process-affected water (OSPW) was studied. Biochar from wheat straw with the highest ash content (14%) had the highest adsorption capacity (0.59 mg/g) followed by biochar from pulp mill sludge, switchgrass, mountain pine, hemp shives, and aspen wood. The adsorption capacity had no obvious trend with surface area, total pore volume, bulk polarity and aromaticity. The large impact of metal content was consistent with the carboxylates (i.e., naphthenate species) in the OSPW binding to the metals (mainly Al and Fe) on the carbon substrate. Although the capacity of biochar is still approximately two orders of magnitude lower than that of a commercial activated carbon, confirming the property (i.e., metal content) that most influenced AEO adsorption, may allow biochar to become competitive with activated carbon after normalizing for cost, especially if this cost includes environmental impacts. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Antioxidant Effects of Grape Vine Cane Extracts from Different Chinese Grape Varieties on Edible Oils

    Directory of Open Access Journals (Sweden)

    Zhuo Min

    2014-09-01

    Full Text Available This study involved the determination of the peroxide value (POV as a measure of the resistance of the oxidation of edible oil with grape vine cane additives to assess their antioxidation potential. The study demonstrated that grape extracts of canes could effectively inhibit the lipid oxidation of edible oils and that this ability varied significantly due to the different extraction solvents employed, as well as to the different varieties of canes used. Lipid oxidation of edible oils was significantly reduced under an accelerated storage condition of 70 ± 1 °C in the presence of Vitamin C (VC, which was chosen as a synergist of grape vine cane extract. A 4:1 ratio of Victoria Blanc-ethyl acetate fraction (EAF and VC led to a significant lowering of the peroxide value and indicated a better antioxidant effect. Thus, these results indicated that some varieties of grape vine cane extracts could be applied as natural antioxidants for elevation of the quality of edible oils in the food industry.

  7. The Effectiveness of Rambutan (Nephelium lappaceum L. Extract in Stabilization of Sunflower Oil under Accelerated Conditions

    Directory of Open Access Journals (Sweden)

    Winne Sia Chiaw Mei

    2014-05-01

    Full Text Available The oxidative properties of sunflower oil supplemented with rambutan extract, (crude extract and its fractionated fraction, SF II in comparison with synthetic antioxidant were investigated. The supplemented sunflower oils were stored under accelerated conditions for 24 days at 60 °C. For every 6-day interval, the oxidative properties of the supplemented sunflower oil were evaluated based on the following tests, namely peroxide value, p-anisidine value, Thiobarbituric Acid Reactive Substances (TBARS assay, iodine value and free fatty acids. The total oxidation (TOTOX values were also calculated based on the peroxide values and p-anisidine values. Rambutan extract is a potential source of antioxidant. The oxidative activities of the extracts at all concentrations were significantly (p < 0.05 higher than the control. Generally, the partially fractionated fraction was more effective than the crude extract. With a 2-year storage period at ambient temperature, the fractionated fraction of the extract, SF II at 300 ppm, was observed to work more effectively than the synthetic antioxidant, t-Tocopherol, and it possessed a protective effect comparable with butylatedhydrioxynanisole (BHA. Therefore, rambutan extract could be used as a potential alternative source of antioxidant in the oil industry or other fat-based products to delay lipid oxidation.

  8. Comparison of Microwave-Assisted and Hydrodistillation Methods for Extraction of Essential Oil from Achillea millefolium

    Directory of Open Access Journals (Sweden)

    S. Mollasalehi

    2013-08-01

    Full Text Available Microwave-assisted hydrodistillation (MAHD method has been compared with hydrodistillation (HD conventional technique for extraction of essential oil from Achillea millefolium. Microwave-assisted hydrodistillation were examined at three levels of microwave powers (300, 500, and 700 W. Obtained results show that MAHD offers important advantages over HD in terms of energy savings and extraction time (20 min against 2.5 h. Also, the essential oils were analyzed by GC-MS. The amount of oxygenated compounds and monoterpene, such as 1,8 -Cineole, Lavandulyl acetate,Caryophylla-dien, Aromadendrene were increased in the microwave method. All these results suggest that MAHD represents an excellent alternative method for extraction of essential oils from plant materials.

  9. Combined Extraction Processes of Lipid from Chlorella vulgaris Microalgae: Microwave Prior to Supercritical Carbon Dioxide Extraction

    Science.gov (United States)

    Dejoye, Céline; Vian, Maryline Abert; Lumia, Guy; Bouscarle, Christian; Charton, Frederic; Chemat, Farid

    2011-01-01

    Extraction yields and fatty acid profiles from freeze-dried Chlorella vulgaris by microwave pretreatment followed by supercritical carbon dioxide (MW-SCCO2) extraction were compared with those obtained by supercritical carbon dioxide extraction alone (SCCO2). Work performed with pressure range of 20–28 Mpa and temperature interval of 40–70 °C, gave the highest extraction yield (w/w dry weight) at 28 MPa/40 °C. MW-SCCO2 allowed to obtain the highest extraction yield (4.73%) compared to SCCO2 extraction alone (1.81%). Qualitative and quantitative analyses of microalgae oil showed that palmitic, oleic, linoleic and α-linolenic acid were the most abundant identified fatty acids. Oils obtained by MW-SCCO2 extraction had the highest concentrations of fatty acids compared to SCCO2 extraction without pretreatment. Native form, and microwave pretreated and untreated microalgae were observed by scanning electronic microscopy (SEM). SEM micrographs of pretreated microalgae present tearing wall agglomerates. After SCCO2, microwave pretreated microalgae presented several micro cracks; while native form microalgae wall was slightly damaged. PMID:22272135

  10. Combined Extraction Processes of Lipid from Chlorella vulgaris Microalgae: Microwave Prior to Supercritical Carbon Dioxide Extraction

    Directory of Open Access Journals (Sweden)

    Farid Chemat

    2011-12-01

    Full Text Available Extraction yields and fatty acid profiles from freeze-dried Chlorella vulgaris by microwave pretreatment followed by supercritical carbon dioxide (MW-SCCO2 extraction were compared with those obtained by supercritical carbon dioxide extraction alone (SCCO2. Work performed with pressure range of 20–28 Mpa and temperature interval of 40–70 °C, gave the highest extraction yield (w/w dry weight at 28 MPa/40 °C. MW-SCCO2 allowed to obtain the highest extraction yield (4.73% compared to SCCO2 extraction alone (1.81%. Qualitative and quantitative analyses of microalgae oil showed that palmitic, oleic, linoleic and α-linolenic acid were the most abundant identified fatty acids. Oils obtained by MW-SCCO2 extraction had the highest concentrations of fatty acids compared to SCCO2 extraction without pretreatment. Native form, and microwave pretreated and untreated microalgae were observed by scanning electronic microscopy (SEM. SEM micrographs of pretreated microalgae present tearing wall agglomerates. After SCCO2, microwave pretreated microalgae presented several micro cracks; while native form microalgae wall was slightly damaged.

  11. The influence of topic and systemic administration of copaiba oil on the alveolar wound healing after tooth extraction in rats.

    Science.gov (United States)

    Dias-da-Silva, Marco A; Pereira, Andresa C; Marin, Miguel Cc; Salgado, Miguel Ac

    2013-10-01

    The Copaiba oil has been used as an auxiliary treatment of inflammations, skin disorders and stomach ulcers, however, in dentistry, this "alternative" medicine has not been investigated yet. The purpose of this study was to evaluate the influence of topic and systemic administration of copaiba oil on the alveolar wound healing after tooth extraction. Twenty-eight wistar male rats had their lower first molar teeth extracted. Subsequently, they were divided in four groups, according to the treatment performed: (a) alveolar socket irrigation with copaiba oil; (b) alveolar socket irrigation with physiological serum; (c) daily gavage with copaiba oil or (d) daily gavage with physiological serum. After the sacrifice, the mandibles were removed and processed in order to obtain decalcified histological sections. The results demonstrated high level of epithelial migration, small number of inflammatory cells and vascular enhancement in the animals which received systemic administration of copaiba oil. The rats treated with topic administration of copaiba oil presented ulcerations and large number of inflammatory cells. An increased bone neoformation was observed in both groups treated with copaiba oil when compared with placebo group. It could be concluded that topic or systemic administration of copaiba oil leads to a better alveolar bone healing, however the topic application on connective tissue should be carefully considered, regarding the whole socket wound healing. Key words:Alveolar wound healing, oil-resin, copaiba.

  12. Oxygen introduction during extraction and the improvement of antioxidant activity of essential oils of basil, lemon and lemongrass

    Directory of Open Access Journals (Sweden)

    Daniele de Freitas Ferreira

    Full Text Available ABSTRACT: Essential oil extraction is commonly carried out by using the hydrodistillation method, which is described in official compendia of food quality control and medicinal plants. Despite the widespread use of this method, few studies have evaluated the effect of the atmosphere change during extraction on the composition and antioxidant activity of essentials oils. Therefore, a study of oxygen introduction influence during the extraction of essential oils from basil, lemongrass and lemon by hydrodistillation was performed. Total amount of oxygenated compounds (e.g., linalool, camphor, α-terpineol, neral, geranial, eugenol and α-muurolol increased for all essential oils extracted under oxygen flow. Antioxidant activity evaluated by using the ORAC method significantly increased (P<0.0001 with oxygen from 618 to 906, 355 to 613 and 72 to 262µmol Trolox g-1 oil for basil, lemongrass and lemon, respectively. Therefore, the simple modification proposed could be considered a suitable alternative to obtain essential oils with higher antioxidant activity.

  13. Optimisation of Microwave-Assisted Extraction of Pomegranate (Punica granatum L. Seed Oil and Evaluation of Its Physicochemical and Bioactive Properties

    Directory of Open Access Journals (Sweden)

    Hasene Keskin Çavdar

    2017-01-01

    Full Text Available Pomegranate seed oil was extracted in a closed-vessel high-pressure microwave system. The characteristics of the obtained oil, such as fatty acid composition, free fatty acidity, total phenolic content, antioxidant activity and colour, were compared to those of the oil obtained by cold solvent extraction. Response surface methodology was applied to optimise extraction conditions: power (176–300 W, time (5–20 min, particle size (d=0.125–0.800 mm and solvent to sample ratio (2:1, 6:1 and 10:1, by mass. The predicted highest extraction yield (35.19 % was obtained using microwave power of 220 W, particle size in the range of d=0.125–0.450 mm and solvent-to-sample ratio of 10:1 (by mass in 5 min extraction time. Microwave-assisted solvent extraction (MASE resulted in higher extraction yield than that of Soxhlet (34.70 % in 8 h or cold (17.50 % in 8 h extraction. The dominant fatty acid of pomegranate seed oil was punicic acid (86 % irrespective of the extraction method. Oil obtained by MASE had bett er physicochemical properties, total phenolic content and antioxidant activity than the oil obtained by cold solvent extraction.

  14. Alkaline Treatment of Oil Palm Frond Fibers by Using Extract of Oil Palm EFB Ash for Better Adhesion toward Polymeric Matrix

    Directory of Open Access Journals (Sweden)

    Warman Fatra

    2015-10-01

    Full Text Available In Indonesia, 187 million tons of biomass were produced from 8.11 million ha of oil palm plantation in 2009. This massive amount of biomass mainly consists of oil palm fronds (OPF and oil palm empty fruit bunches (EFB, which are normally categorized as waste. The properties of OPF fibers compared to those of synthetic fibers, such as low density, low cost, less abrasion of equipment, and safer production, makes them an attractive reinforcement for composite materials. In this work, the utilization of oil palm empty fruit bunch ash for OPF fiber-polyester resin composite and the effect of process conditions were studied. Water absorption, tensile and flexural strength were used to characterize the effects of alkaline treatment on modified OPF fibers in polyester resin. The investigation focused on the effect of alkaline treatment time. Treatment temperature and liquid to solid ratio were analyzed using Response Surface Method-Central Composite Design (RSM-CCD. The highest tensile strength (44.87 MPa was achieved at 12 hours soaking time, at 40°C treatment temperature and 5:1 water to ash ratio. The highest flexural strength (120.50 MPa was obtained at 1.3 hours soaking time, 4 dissolving ratio and 35°C treatment temperature. The lowest water absorption of composite (3.00% was achieved at the longest soaking time (14.7 hours, 4 dissolving ratio and 35°C treatment temperature. Variance of soaking time, dissolving ratio and temperature in the alkaline treatment process using extract of oil palm empty fruit bunch ash significantly affected the mechanical and physical properties of the oil palm frond fibers reinforced composite.

  15. In vitro efficacy of essential oils and extracts of Schinus molle L. against Ctenocephalides felis felis.

    Science.gov (United States)

    Batista, Lilian C De S O; Cid, Yara P; De Almeida, Ana Paula; Prudêncio, Edlene R; Riger, Cristiano J; De Souza, Marco A A; Coumendouros, Katherine; Chaves, Douglas S A

    2016-04-01

    Extracts and essential oils from plants are important natural sources of pesticides. These compounds are considered an alternative to control ectoparasites of veterinary importance. Schinus molle, an endemic species of Brazil, produces a high level of essential oil and several other compounds. The aim of this work was to determinate the chemical composition of extracts and essential oils of S. molle and further to evaluate the activity against eggs and adults of Ctenocephalides felis felis, a predominant flea that infests dogs and cats in Brazil. In an in vitro assay, the non-polar (n-hexane) extract showed 100% efficacy (800 µg cm(-2); LD50 = 524·80 µg cm(-2)) at 24 and 48 h. Its major compound was lupenone (50·25%). Essential oils from fruits and leaves were evaluated, and had 100% efficacy against adult fleas at 800 µg cm(-2) (LD50 = 353·95 µg cm(-2)) and at 50 µg cm(-2) (LD50 = 12·02 µg cm(-2)), respectively. On the other hand, the essential oil from fruits and leaves was not active against flea eggs. This is the first study that reports the insecticidal effects of essential oils and extracts obtained from Schinus molle against Ctenocephalides felis felis.

  16. Effects of process parameters on peanut skins extract and CO2 diffusivity by supercritical fluid extraction

    Science.gov (United States)

    Putra, N. R.; Yian, L. N.; Nasir, H. M.; Idham, Z. Binti; Yunus, M. A. C.

    2018-03-01

    Peanut skins (Arachis hypogea) are an agricultural waste product which has received much attention because they contain high nutritional values and can be potentially utilized in difference industries. At present, only a few studies have been conducted to study the effects of parameters on the peanut skins oil extraction. Therefore, this study aimed to determine the best extraction condition in order to obtain the highest extract yield using supercritical carbon dioxide (SC-CO2) with co-solvent Ethanol as compared to Soxhlet extraction method. Diffusivity of carbon dioxide in supercritical fluid extraction was determined using Crank model. The mean particle size used in this study was 425 µm. The supercritical carbon dioxide was performed at temperature (40 – 70 °C), flow rate of co-solvent ethanol (0 - 7.5% Vethanol/Vtotal), and extraction pressure (10 – 30 MPa) were used in this studies. The results showed that the percentage of oil yields and effective diffusivity increase as the pressure, rate of co-solvent, and temperature increased.

  17. Ionic liquid-based microwave-assisted extraction of essential oil and biphenyl cyclooctene lignans from Schisandra chinensis Baill fruits.

    Science.gov (United States)

    Ma, Chun-hui; Liu, Ting-ting; Yang, Lei; Zu, Yuan-gang; Chen, Xiaoqiang; Zhang, Lin; Zhang, Ying; Zhao, Chunjian

    2011-12-02

    Ionic liquid-based microwave-assisted extraction (ILMAE) has been successfully applied in extracting essential oil and four kinds of biphenyl cyclooctene lignans from Schisandra chinensis Baill. 0.25 M 1-lauryl-3-methylimidazolium bromide ionic liquid is selected as solvent. The optimum parameters of dealing with 25.0 g sample are 385 W irradiation power, 40 min microwave extraction time and 1:12 solid-liquid ratio. The yields of essential oil and lignans are 12.12±0.37 ml/kg and 250.2±38.2 mg/kg under the optimum conditions. The composition of the essential oil extracted by hydro-distillation, steam-distillation and ILMAE is analyzed by GC-MS. With ILMAE method, the energy consumption time has not only been shortened to 40 min (hydro-distillation 3.0 h for extracting essential oil and reflux extraction 4.0 h for extracting lignans, respectively), but also the extraction efficiency has been improved (extraction of lignans and distillation of essential oil at the same time) and reduces the environmental pollution. S. chinensis materials treated by different methods are observed by scanning electronic microscopy. Micrographs provide more evidence to prove that ILMAE is a better and faster method. The experimental results also indicate that ILMAE is a simple and efficient technique for sample preparation. Copyright © 2011 Elsevier B.V. All rights reserved.

  18. IR and Raman studies of oil and seedcake extracts from natural and genetically modified flax seeds

    Science.gov (United States)

    Żuk, M.; Dymińska, L.; Kulma, A.; Boba, A.; Prescha, A.; Szopa, J.; Mączka, M.; Zając, A.; Szołtysek, K.; Hanuza, J.

    2011-03-01

    Flax plant of the third generation (F3) overexpressing key genes of flavonoid pathway cultivated in field in 2008 season was used as the plant material throughout this study. The biochemical properties of seed, oil and seedcake extracts from natural and transgenic flax plants were compared. Overproduction of flavonoids (kaempferol), phenolic acids (coumaric, ferulic/synapic) and lignan-secoisolariciresinol diglucoside (SDG) in oil and extracts from transgenic seeds has been revealed providing a valuable source of these compounds for biotechnological application. The changes in fatty acids composition and increase in their stability against oxidation along three plant generations were also detected. The analysis of oil and seedcake extracts was performed using Raman and IR spectroscopy. The wavenumbers and integral intensities of Raman and IR bands were used to identify the components of phenylpropanoid pathway in oil and seedcake extracts from control and transgenic flax seeds. The spectroscopic data were compared to those obtained from biochemical analysis.

  19. Process for complete conversion of coal oils, shale oils, etc

    Energy Technology Data Exchange (ETDEWEB)

    Dubois, P

    1911-07-08

    A process is described for complete conversion of mineral coal oil, shale oil, and other similar oils in pitch, characterized by these oils being mixed with a nonvolatile substance with a boiling point on the average higher than the boiling point of the oil to be treated, and then being heated under pressure with the introduction of air, whereby the heating is interrupted if necessary on account of the known exothermic reaction and the conversion of the oil in the pitch or its distillation can be carried out without further heating.

  20. Recovery of oil components of okara by ethanol-modified supercritical carbon dioxide extraction.

    Science.gov (United States)

    Quitain, Armando T; Oro, Kazuyuki; Katoh, Shunsaku; Moriyoshi, Takashi

    2006-09-01

    Recovery of the oil components of okara by ethanol-modified supercritical carbon dioxide extraction was investigated at 40-80 degrees C temperature and 12-30 MPa pressure. In a typical run (holding period of 2 h, continuous flow extraction of 5 h), results indicated that the oil component could be best obtained with a recovery of 63.5% at relatively low temperature of 40 degrees C and mild pressure of 20 MPa in the presence of 10 mol% EtOH as entrainer. Based on gas chromatography-mass spectrometry (GC-MS) analysis, the extracts consisted mainly of fatty acids and phytosterols, and traces of decadienal. Folin-Ciocalteau estimates of total phenols showed that addition of EtOH as entrainer increased the yield and the amount of phenolic compounds in the extracts. The amounts of two primary soy isoflavones, genistein and daidzein, in the extracts also increased with increasing amount of EtOH.

  1. Influence of mixing and extraction parameters on virgin olive oil quality

    Directory of Open Access Journals (Sweden)

    Pasqualone, A.

    2001-08-01

    Full Text Available The mixing time, the temperature and the degree of dilution of olive paste are the main parameters liable to change during mixing and oil ext raction. They can greatly differ from a processing run to another, with variations being observed in Tuscan oil mills, between 26ºC and 36ºC, 40’ and 90’, and 10% and 50% respectively, for the temperature, the mixing time and the water added during the centrifugal extraction. This note reports on the results of some experimental trials run during the 1998 olive oil year in Tuscany. The mixing time and temperature as well as the olive paste dilution were changed one at a time and were assessed for their influence on extraction yield and oil quality. The best conditions to optimise the product yield and quality were identified.El tiempo de batido, la temperatura y el grado de dilución de la pasta de aceituna, son los principales parámetros que pueden sufrir cambios durante el batido y la extracción del aceite. Estos pueden diferir mucho de un proceso a otro, habiendo sido observadas variaciones en los aceites de molino de Toscana, entre 26ºC y 36ºC, 40’ y 90’, y 10% y 50% respectivamente, para la temperatura, el tiempo de batido y el agua añadida durante la extracción por centrifugación. Este artículo presenta los resultados de algunos ensayos experimentales realizados durante el año 1998 con aceite de oliva de Toscana. El tiempo de batido y la temperatura, así como la dilución de la pasta de aceitunas, se variaron uno a uno y se evaluaron por su influencia en el rendimiento de la extracción y la calidad del aceite. Las mejores condiciones para optimizar el rendimiento y la calidad del producto fueron identificadas.

  2. The insecticidal activity of some extracts and oils of some tropical ...

    African Journals Online (AJOL)

    The effect of ethanolic extract on larvae of E. vapidella at an application rate of 0.6 and 3.3% were low since there was no significant difference (P > 0.05) when compared with the control. The effect of oil extract was greater in the slices protected with Monodora tenuifolia and there was no egg hatch and adult emergence.

  3. Production of three types of krill oils from krill meal by a three-step solvent extraction procedure.

    Science.gov (United States)

    Xie, Dan; Mu, Hongyan; Tang, Tianpei; Wang, Xiaosan; Wei, Wei; Jin, Jun; Wang, Xingguo; Jin, Qingzhe

    2018-05-15

    In this study, a three-step extraction method (separately use acetone, hexane, and ethanol as extraction solvent in each step) was conducted to selectively extract three types of krill oils with different compositions. The lipid yields were 5.08% in step 1, 4.80% in step 2, and 9.11% in step 3, with a total of 18.99%. The krill oil extracted with acetone in step 1 (A-KO) contained the lowest contents of phospholipids (PL) (2.32%) and n-3 polyunsaturated fatty acids (PUFA) (16.63%), but the highest levels of minor components (505.00 mg/kg of astaxanthin, 29.39 mg/100 g of tocopherols, 34.32 mg/100 g of vitamin A and 27.95 mg/g of cholesterol). By contrast, despite having traces of minor components, the krill oil extracted using ethanol in step 3 (E-KO) was the most abundant in PL (59.52%) and n-3 PUFA (41.74%). The krill oil extracted using hexane in step 2 (H-KO) expressed medium contents of all the testing indices. The oils showed significant differences in the antioxidant capacity (E-KO > H-KO > A-KO) which exhibited positive correlation with the PL content. These results could be used for further development of a wide range of krill oil products with tailor-made functions. Copyright © 2017 Elsevier Ltd. All rights reserved.

  4. Antioxidant and antidermatophytic activities of essential oil and extracts of Metasequoia glyptostroboides Miki ex Hu.

    Science.gov (United States)

    Bajpai, Vivek K; Yoon, Jung In; Chul Kang, Sun

    2009-06-01

    This study was undertaken to assess the antioxidant and antidermatophytic potential of the essential oil and extracts (hexane, chloroform, ethyl acetate and methanol) of Metasequoia glyptostroboides Miki ex Hu. Antioxidant activity was evaluated by using 1,1-diphenyl-2-picrylhydrazyl (DPPH) assay. The free radical scavenging activities of the oil and ethyl acetate extract were found to be superior (IC(50)=9.1 and 14.24 microg/ml, respectively) as compared to butylatedhydroxyanisole (BHA), (IC(50)=18.27 microg/ml). Also the ethyl acetate extract revealed the highest phenolic contents (93.26 mg/g of dry wt) as compared to the other extracts. Further, oil (1250 microg/disc) and extracts (1750 microg/disc) revealed 35.33-67.66 and 18.0-53.3% antidermatophytic effect, respectively, along with their respective MIC values (62.5-500 and 250-4000 microg/ml) against Trichophyton rubrum KCTC 6345, T. rubrum KCTC 6375, T. rubrum KCTC 6352, T. mentagrophytes KCTC 6085, T. mentagrophytes KCTC 6077, T. mentagrophytes KCTC 6316, Microsporum canis KCTC 6591, M. canis KCTC 6348 and M. canis KCTC 6349. The oil also had a strong detrimental effect on spore germination as well as concentration and time-dependent kinetic inhibition of M. canis KCTC 6591.

  5. Optimisation of Microwave-Assisted Extraction of Pomegranate (Punica granatum L.) Seed Oil and Evaluation 
of Its Physicochemical and Bioactive Properties.

    Science.gov (United States)

    Çavdar, Hasene Keskin; Yanık, Derya Koçak; Gök, Uğur; Göğüş, Fahrettin

    2017-03-01

    Pomegranate seed oil was extracted in a closed-vessel high-pressure microwave system. The characteristics of the obtained oil, such as fatty acid composition, free fatty acidity, total phenolic content, antioxidant activity and colour, were compared to those of the oil obtained by cold solvent extraction. Response surface methodology was applied to optimise extraction conditions: power (176-300 W), time (5-20 min), particle size ( d =0.125-0.800 mm) and solvent to sample ratio (2:1, 6:1 and 10:1, by mass). The predicted highest extraction yield (35.19%) was obtained using microwave power of 220 W, particle size in the range of d =0.125-0.450 mm and solvent-to-sample ratio of 10:1 (by mass) in 5 min extraction time. Microwave-assisted solvent extraction (MASE) resulted in higher extraction yield than that of Soxhlet (34.70% in 8 h) or cold (17.50% in 8 h) extraction. The dominant fatty acid of pomegranate seed oil was punicic acid (86%) irrespective of the extraction method. Oil obtained by MASE had better physicochemical properties, total phenolic content and antioxidant activity than the oil obtained by cold solvent extraction.

  6. Effect of lithium salts addition on the ionic liquid based extraction of essential oil from Farfarae Flos.

    Science.gov (United States)

    Li, Zhen-Yu; Zhang, Sha-Sha; Jie-Xing; Qin, Xue-Mei

    2015-01-01

    In this study, an ionic liquids (ILs) based extraction approach has been successfully applied to the extraction of essential oil from Farfarae Flos, and the effect of lithium chloride was also investigated. The results indicated that the oil yields can be increased by the ILs, and the extraction time can be reduced significantly (from 4h to 2h), compared with the conventional water distillation. The addition of lithium chloride showed different effect according to the structures of ILs, and the oil yields may be related with the structure of cation, while the chemical compositions of essential oil may be related with the anion. The reduction of extraction time and remarkable higher efficiency (5.41-62.17% improved) by combination of lithium salt and proper ILs supports the suitability of the proposed approach. Copyright © 2014 Elsevier B.V. All rights reserved.

  7. Chemical composition profiling and antifungal activity of the essential oil and plant extracts of Mesembryanthemum edule (L.) bolus leaves.

    Science.gov (United States)

    Omoruyi, Beauty Etinosa; Afolayan, Anthony Jide; Bradley, Graeme

    2014-01-01

    Essential oil from Mesembryanthemum edule leaves have been used by the Eastern Cape traditional healers for the treatment of respiratory tract infections, tuberculosis, dysentery, diabetic mellitus, laryngitis and vaginal infections. The investigation of bioactive compounds in the essential oil of this plant could help to verify the efficacy of the plant in the management or treatment of these illnesses. Various concentrations of the hydro-distilled essential oil, ranging from 0.005-5 mg/ml, were tested against some fungal strains, using the micro-dilution method. Minimum inhibitory activity was compared with four other different crude extracts of hexane, acetone, ethanol and aqueous samples from the same plant. The chemical composition of the essential oil, hexane, acetone and ethanol extracts was determined using GC-MS. GC/MS analysis of the essential oil resulted in the identification of 28 compounds, representing 99.99% of the total oil. Phytoconstituents of hexane, acetone and ethanol extracts yielded a total peak chromatogram of fifty nine compounds. A total amount of 10.6% and 36.61% of the constituents were obtained as monoterpenes and oxygenated monoterpenes. Sesquiterpene hydrocarbons (3.58%) were relatively low compared to the oxygenated sesquiterpenes (9.28%), while the major concentrated diterpenes and oxygenated diterpenes were 1.43% and 19.24 %, respectively and phytol 12.41%. Total amount of fatty acids and their methyl esters content, present in the oil extract, were found to be 19.25 %. Antifungal activity of the oil extract and four solvent extracts were tested against five pathogenic fungal strains. The oil extract showed antifungal activity against Candida albican, Candida krusei, Candida rugosa, Candida glabrata and Cryptococcus neoformans with MIC ranges of 0.02 0.31 mg/ml. Hexane extract was active against the five fungal strains with MICs ranging between 0.02-1.25 mg/ml. Acetone extracts were active against C. krusei only at 0.04mg/ml. No

  8. A systematic framework for CAFD and resources allocation optimisation using MINLP in vegetable oil processing

    DEFF Research Database (Denmark)

    Quaglia, Alberto; Sarup, Bent; Sin, Gürkan

    Although being a mature and well established industry segment, over the last few decades the vegetable oil industry has been facing many important new challenges due to emerging new products (such as biodiesel and nutraceuticals compounds), as well as new trends and regulations with regards....... In this paper, a systematic framework for Computer-Aided Flowsheet Syntesis and Design (CAFD) and resources allocation for the vegetable oil sector is presented. In the framework a Mixed Integer Non Linear Programming (MINLP) problem is formulated and solved for a soybean processing case study, to determine...... the optimal processing network for vegetable oil extraction and refining (including biodiesel production and various options for byproducts valorization), as well as the optimal material flows to each processing step. In order to optimize the resources needed to solve such a large and complex problem...

  9. Activity of Six Essential Oils Extracted from Tunisian Plants against Legionella pneumophila.

    Science.gov (United States)

    Chaftar, Naouel; Girardot, Marion; Quellard, Nathalie; Labanowski, Jérôme; Ghrairi, Tawfik; Hani, Khaled; Frère, Jacques; Imbert, Christine

    2015-10-01

    The aim of this study was to investigate the composition of six essential oils extracted from Tunisian plants, i.e., Artemisia herba-alba Asso, Citrus sinensis (L.) Osbeck, Juniperus phoenicea L., Rosmarinus officinalis L., Ruta graveolens L., and Thymus vulgaris L., and to evaluate their activity against Legionella pneumophila (microdilution assays). Eight Legionella pneumophila strains were studied, including the two well-known serogroup 1 Lens and Paris strains as controls and six environmental strains isolated from Tunisian spas belonging to serogroups 1, 4, 5, 6, and 8. The essential oils were generally active against L. pneumophila. The activities of the A. herba-alba, C. sinensis, and R. officinalis essential oils were strain-dependent, whereas those of the J. phoenicea and T. vulgaris oils, showing the highest anti-Legionella activities, with minimum inhibitory concentrations (MICs) lower than 0.03 and lower than or equal to 0.07 mg/ml, respectively, were independent of the strains' serogroup. Moreover, the microorganisms treated with T. vulgaris essential oil were shorter, swollen, and less electron-dense compared to the untreated controls. Isoborneol (20.91%), (1S)-α-pinene (18.30%) β-phellandrene (8.08%), α-campholenal (7.91%), and α-phellandrene (7.58%) were the major components isolated from the J. phoenicea oil, while carvacrol (88.50%) was the main compound of the T. vulgaris oil, followed by p-cymene (7.86%). This study highlighted the potential interest of some essential oils extracted from Tunisian plants as biocides to prevent the Legionella risk. Copyright © 2015 Verlag Helvetica Chimica Acta AG, Zürich.

  10. Optimization of Supercritical CO2 Extraction of Fish Oil from Viscera of African Catfish (Clarias gariepinus)

    Science.gov (United States)

    Sarker, Mohamed Zaidul Islam; Selamat, Jinap; Habib, Abu Sayem Md. Ahsan; Ferdosh, Sahena; Akanda, Mohamed Jahurul Haque; Jaffri, Juliana Mohamed

    2012-01-01

    Fish oil was extracted from the viscera of African Catfish using supercritical carbon dioxide (SC-CO2). A Central Composite Design of Response Surface methodology (RSM) was employed to optimize the SC-CO2 extraction parameters. The oil yield (Y) as response variable was executed against the four independent variables, namely pressure, temperature, flow rate and soaking time. The oil yield varied with the linear, quadratic and interaction of pressure, temperature, flow rate and soaking time. Optimum points were observed within the variables of temperature from 35 °C to 80 °C, pressure from 10 MPa to 40 MPa, flow rate from 1 mL/min to 3 mL/min and soaking time from 1 h to 4 h. However, the extraction parameters were found to be optimized at temperature 57.5 °C, pressure 40 MPa, flow rate 2.0 mL/min and soaking time 2.5 h. At this optimized condition, the highest oil yields were found to be 67.0% (g oil/100 g sample on dry basis) in the viscera of catfish which was reasonable to the yields of 78.0% extracted using the Soxhlet method. PMID:23109854

  11. Optimization of Supercritical CO2 Extraction of Fish Oil from Viscera of African Catfish (Clarias gariepinus

    Directory of Open Access Journals (Sweden)

    Mohamed Zaidul Islam Sarker

    2012-09-01

    Full Text Available Fish oil was extracted from the viscera of African Catfish using supercritical carbon dioxide (SC-CO2. A Central Composite Design of Response Surface methodology (RSM was employed to optimize the SC-CO2 extraction parameters. The oil yield (Y as response variable was executed against the four independent variables, namely pressure, temperature, flow rate and soaking time. The oil yield varied with the linear, quadratic and interaction of pressure, temperature, flow rate and soaking time. Optimum points were observed within the variables of temperature from 35 °C to 80 °C, pressure from 10 MPa to 40 MPa, flow rate from 1 mL/min to 3 mL/min and soaking time from 1 h to 4 h. However, the extraction parameters were found to be optimized at temperature 57.5 °C, pressure 40 MPa, flow rate 2.0 mL/min and soaking time 2.5 h. At this optimized condition, the highest oil yields were found to be 67.0% (g oil/100 g sample on dry basis in the viscera of catfish which was reasonable to the yields of 78.0% extracted using the Soxhlet method.

  12. Extraction and analysis of tea (Camellia sinensis) seed oil from ...

    African Journals Online (AJOL)

    OMONDI-GUYA

    2013-02-20

    Feb 20, 2013 ... spectrophotometer (Model JENWAY6705, multi-cell changer) against a blank ... All the tea seed oil extracts were golden yellow in color and liquid at .... respectively, the two being products of oxidative rancidity. (Chindo et al.

  13. [Extraction and analysis of chemical components of essential oil in Thymus vulgaris of tissue culture].

    Science.gov (United States)

    Li, Xiao-Dong; Yang, Li; Xu, Shi-Qian; Li, Jian-Guo; Cheng, Zhi-Hui; Dang, Jian-Zhang

    2011-10-01

    To extract the essential oils from the Seedlings, the Aseptic Seedlings and the Tissue Culture Seedlings of Thymus vulgaris and analyze their chemical components and the relative contents. The essential oils were extracted by steam distillation, the chemical components and the relative contents were identified and analyzed by gas chromatography-mass spectrometry (GC/MS) and peak area normalization method. The main chemical components of essential oil in these three samples had no significant difference, they all contained the main components of essential oil in Thymus vulgaris: Thymol, Carvacrol, o-Cymene, gamma-Terpinene, Caryophyllene et al. and only had a slight difference in the relative content. This study provides important theoretical foundation and data reference for further study on production of essential oil in thyme by tissue culture technology.

  14. Co-processing of standard gas oil and biocrude oil to hydrocarbon fuels

    International Nuclear Information System (INIS)

    Agblevor, Foster A.; Mante, O.; McClung, R.; Oyama, S.T.

    2012-01-01

    The major obstacle in thermochemical biomass conversion to hydrocarbon fuels using pyrolysis has been the high oxygen content and the poor stability of the product oils, which cause them to solidify during secondary processing. We have developed a fractional catalytic pyrolysis process to convert biomass feedstocks into a product termed “biocrude oils” (stable biomass pyrolysis oils) which are distinct from unstable conventional pyrolysis oils. The biocrude oils are stable, low viscosity liquids that are storable at ambient conditions without any significant increases in viscosity; distillable at both atmospheric pressure and under vacuum without char or solid formation. About 15 wt% biocrude oils containing 20–25% oxygen were blended with 85 wt% standard gas oil and co-cracked in an Advanced Catalyst Evaluation (ACE™) unit using fluid catalytic cracking (FCC) catalysts to produce hydrocarbon fuels that contain negligible amount of oxygen. For the same conversion of 70% for both the standard gas oil and the biocrude oil/gas oil blends, the product gasoline yield was 44 wt%, light cycle oil (LCO) 17 wt%, heavy cycle oil (HCO) 13 wt%, and liquefied petroleum gas (LPG) 16 wt%. However, the coke yield for the standard gas oil was 7.06 wt% compared to 6.64–6.81 wt% for the blends. There appeared to be hydrogen transfer from the cracking of the standard gas oil to the biocrude oil which subsequently eliminated the oxygen in the fuel without external hydrogen addition. We have demonstrated for the first time that biomass pyrolysis oils can be successfully converted into hydrocarbons without hydrogenation pretreatment. -- Highlights: ► The co-processed product had less than 1% oxygen content and contained biocarbons determined by 14 C analysis. ► The co-processing did not affect the yields of gasoline, LCO, and HCO. ► First demonstration of direct conversion of pyrolysis oils into drop-in hydrocarbon fuels.

  15. Jojoba oil: A state of the art review and future prospects

    International Nuclear Information System (INIS)

    Sánchez, Marcos; Avhad, Mangesh R.; Marchetti, Jorge M.; Martínez, Mercedes; Aracil, José

    2016-01-01

    Highlights: • Jojoba oil is a unique oil formed by long esters instead of triglycerides. • Jojoba cake is gaining interest because of the extraction of valuable chemicals. • Jojoba oil heterogeneous-catalyzed methanolysis makes the process more profitable. - Abstract: Jojoba oil, which is derived from the extraction of Jojoba seed, has a peculiar molecular structure in comparison with the rest of conventional oils. Jojoba oil is formed by long monounsaturated esters whereas the rest of the oils are usually composed by triglycerides. This unconventional structure confers to Jojoba oil unique properties and characteristics that are very valuable for fine chemical industry and for the production of pharmaceuticals. In addition, Jojoba oil can be an excellent source of fatty acid alkyl esters or biodiesel after the transesterification process and the purification steps. This review presents general information about the production of Jojoba oil and its derivatives, its composition, oil extraction process and the applications of this oil when it is used directly or after chemical transformation as well as the possible purposes of Jojoba meal after extraction. In addition, this paper contemplates the advantages and disadvantages of the use of homogeneous and heterogeneous catalysts for the Jojoba oil transesterification as well as different methods to obtain long monounsaturated alcohols, which have pharmaceutical applications, after being separated from biodiesel. The properties of the products derived from the transesterification of Jojoba oil are broadly discussed. Moreover, this review suggests future research opportunities such as a possible biorefinery using Jojoba oil as main raw material, supercritical methods and simultaneous extraction/reaction process which are fully discussed.

  16. Improvement of stability and carotenoids fraction of virgin olive oils by addition of microalgae Scenedesmus almeriensis extracts.

    Science.gov (United States)

    Limón, Piedad; Malheiro, Ricardo; Casal, Susana; Acién-Fernández, F Gabriel; Fernández-Sevilla, José M; Rodrigues, Nuno; Cruz, Rebeca; Bermejo, Ruperto; Pereira, José Alberto

    2015-05-15

    Humans are not capable of synthesizing carotenoids de novo and thus, their presence in human tissues is entirely of dietary origin. Consumption of essential carotenoids is reduced due to the lower intake of fruits and vegetables. Microalgae are a good source of carotenoids that can be exploited. In the present work, carotenoids rich extracts from Scenedesmus almeriensis were added to extra-virgin olive oils at different concentrations (0.1 and 0.21 mg/mL) in order to enhance the consumption of these bioactives. Extracts brought changes in olive oils color, turning them orange-reddish. Quality of olive oils was improved, since peroxidation was inhibited. Olive oils fatty acids and tocopherols were not affected. β-carotene and lutein contents increase considerably, as well as oxidative stability, improving olive oils shelf-life and nutritional value. Inclusion of S. almeriensis extracts is a good strategy to improve and enhance the consumption of carotenoids, since olive oil consumption is increasing. Copyright © 2014 Elsevier Ltd. All rights reserved.

  17. Systematic methodology and property prediction of fatty systems for process design/analysis in the oil and fat industry

    DEFF Research Database (Denmark)

    Díaz Tovar, Carlos Axel; Ceriani, Roberta; Gani, Rafiqul

    2010-01-01

    in the vegetable oil were defined. Basic and critical properties were then computed by means of appropriate property prediction software. Temperature dependant properties were modeled using and extending available correlations. The process model was developed through the PRO II commercial simulator and validated......A systematic model based methodology has been developed and its application highlighted through the solvent recovery section of a soybean oil extraction process, with emphasis on the effect of design variables on the process performance. First, the most representative compounds present...

  18. Pre-clinical evaluation of extracts and essential oils from betel-like ...

    African Journals Online (AJOL)

    The extracts and oils were preclinically studied based on cyto - and genotoxicity using microculture tetrazolium (MTT) and comet assays. Results: The crude extracts showed an IC50 in leukocytes and HeLa cells of 58.59 -97.31 mg/ml and 34.91-101.79 mg/ml, the LD50 is higher than 5000 mg/kg. With lower values than the ...

  19. Physical and chemical properties of olive oil extracted from olive cultivars grown in Shiraz and Kazeroon

    DEFF Research Database (Denmark)

    Homapour, M.; Hamedi, M.; Moslehishad, M.

    2014-01-01

    Background and objective: The composition of olive oil is significantly affected by the cultivar and climatic conditions. The present study determined the chemical characteristics of olive oil extracted from two major Iranian varieties of olive (yellow and local oil-grade) in Shiraz and Kazeroon......, two major olive-producing areas in Fars province. Materials and methods: The composition of olive oil is significantly affected by the cultivar and climatic conditions. The present study determined the chemical characteristics of olive oil extracted from two major Iranian varieties of olive (yellow...... and local oil-grade) in Shiraz and Kazeroon, two major olive-producing areas in Fars province. Results: The results showed that the physical and chemical properties of both cultivars are in accordance with national and international standards. There was a significant difference in acidity, iodine content...

  20. Comparison of microwave hydrodistillation and solvent-free microwave extraction of essential oil from Melaleuca leucadendra Linn

    Science.gov (United States)

    Ismanto, A. W.; Kusuma, H. S.; Mahfud, M.

    2017-12-01

    The comparison of solvent-free microwave extraction (SFME) and microwave hydrodistillation (MHD) in the extraction of essential oil from Melaleuca leucadendra Linn. was examined. Dry cajuput leaves were used in this study. The purpose of this study is also to determine optimal condition (microwave power). The relative electric consumption of SFME and MHD methods are both showing 0,1627 kWh/g and 0,3279 kWh/g. The results showed that solvent-free microwave extraction methods able to reduce energy consumption and can be regarded as a green technique for extraction of cajuput oil.

  1. Influence of the extraction method and storage time on the physicochemical properties and carotenoid levels of pequi (Caryocar brasiliense Camb. oil

    Directory of Open Access Journals (Sweden)

    Milton Cosme Ribeiro

    2012-06-01

    Full Text Available The objective of this study was to analyze the physicochemical properties and carotenoid levels of pequi oil obtained by different extraction methods and to evaluate the preservation of these properties and pigments during storage time. The pequi oil was obtained by solvent extraction, mechanical extraction, and hot water flotation. It was stored for over 180 days in an amber bottle at ambient conditions. Analyses for the determination of the acidity, peroxide, saponification and iodine values, coloration, total carotenoids, and β-carotene levels were conducted. The oil extraction with solvents produced the best yield and carotenoid levels. The oil obtained by mechanical extraction presented higher acidity (5.44 mg KOH.g-1 and peroxide values (1.07 mEq.kg-1. During the storage of pequi oil, there was an increase in the acidity and the peroxide values, darkening of the oil coloration, and a reduction of the carotenoid levels. Mechanical extraction is the less advantageous method for the conservation of the physicochemical properties and carotenoid levels in pequi oil.

  2. Molecular imprinting solid phase extraction for selective detection of methidathion in olive oil.

    Science.gov (United States)

    Bakas, Idriss; Oujji, Najwa Ben; Moczko, Ewa; Istamboulie, Georges; Piletsky, Sergey; Piletska, Elena; Ait-Ichou, Ihya; Ait-Addi, Elhabib; Noguer, Thierry; Rouillon, Régis

    2012-07-13

    A specific adsorbent for extraction of methidathion from olive oil was developed. The design of the molecularly imprinted polymer (MIP) was based on the results of the computational screening of the library of polymerisable functional monomers. MIP was prepared by thermal polymerisation using N,N'-methylene bisacrylamide (MBAA) as a functional monomer and ethylene glycol dimethacrylate (EGDMA) as a cross-linker. The polymers based on the itaconic acid (IA), methacrylic acid (MAA) and 2-(trifluoromethyl)acryl acid (TFMAA) functional monomers and one control polymer which was made without functional monomers with cross-linker EGDMA were also synthesised and tested. The performance of each polymer was compared using corresponding imprinting factor. As it was predicted by molecular modelling the best results were obtained for the MIP prepared with MBAA. The obtained MIP was optimised in solid-phase extraction coupled with high performance liquid chromatography (MISPE-HPLC-UV) and tested for the rapid screening of methidathion in olive oil. The proposed method allowed the efficient extraction of methidathion for concentrations ranging from 0.1 to 9 mg L(-1) (r(2)=0.996). The limits of detection (LOD) and quantification (LOQ) in olive oil were 0.02 mg L(-1) and 0.1 mg L(-1), respectively. MIPs extraction was much more effective than traditional C18 reverse-phase solid phase extraction. Copyright © 2012 Elsevier B.V. All rights reserved.

  3. Pressurized liquid extraction and chemical characterization of safflower oil: A comparison between methods.

    Science.gov (United States)

    Conte, Rogério; Gullich, Letícia M D; Bilibio, Denise; Zanella, Odivan; Bender, João P; Carniel, Naira; Priamo, Wagner L

    2016-12-15

    This work investigates the extraction process of safflower oil using pressurized ethanol, and compares the chemical composition obtained (in terms of fatty acids) with other extraction techniques. Soxhlet and Ultrasound showed maximum global yield of 36.53% and 30.41%, respectively (70°C and 240min). PLE presented maximum global yields of 25.62% (3mLmin(-1)), 19.94% (2mLmin(-1)) and 12.37% (1mLmin(-1)) at 40°C, 100bar and 60min. Palmitic acid showed the lower concentration in all experimental conditions (from 5.70% to 7.17%); Stearic and Linoleic acid presented intermediate concentrations (from 2.93% to 25.09% and 14.09% to 19.06%, respectively); Oleic acid showed higher composition (from 55.12% to 83.26%). Differences between percentages of fatty acids, depending on method were observed. Results may be applied to maximize global yields and select fatty acids, reducing the energetic costs and process time. Copyright © 2016 Elsevier Ltd. All rights reserved.

  4. Process for separating and recovering oil from oil-sands, etc

    Energy Technology Data Exchange (ETDEWEB)

    Preller, H

    1921-02-24

    A process for separating and recovering oil from oil-sands, bitumen from oil-chalk, oil-shale, and coal, according to Patent 400,122, is described. It is characterized in that the mined material falling on account of its weight is exposed to the running hot water in circulation through the wash-chamber and the clarifying chamber arranged separate or built on (circulation) being obtained by pumps or injectors in a regulatable motion.

  5. Comprehension of direct extraction of hydrophilic antioxidants using vegetable oils by polar paradox theory and small angle X-ray scattering analysis.

    Science.gov (United States)

    Li, Ying; Fabiano-Tixier, Anne Sylvie; Ruiz, Karine; Rossignol Castera, Anne; Bauduin, Pierre; Diat, Olivier; Chemat, Farid

    2015-04-15

    Since the polar paradox theory rationalised the fact that polar antioxidants are more effective in nonpolar media, extractions of phenolic compounds in vegetable oils were inspired and achieved in this study for obtaining oils enriched in phenolic compounds. Moreover, the influence of surfactants on the extractability of phenolic compounds was experimentally studied first, followed by the small angle X-ray scattering analysis for the oil structural observation before and after extraction so as to better understand the dissolving mechanism underpinning the extraction. The results showed a significant difference on the extraction yield of phenolic compounds among oils, which was mainly dependent on their composition instead of the unsaturation of fatty acids. Appropriate surfactant additions could significantly improve extraction yield for refined sunflower oils, which 1% w/w addition of glyceryl oleate was determined as the optimal. Besides, 5% w/w addition of lecithin performed the best in oil enrichments compared with mono- and di-glycerides. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. The effects of process technology on the physicochemical properties of peony seed oil

    International Nuclear Information System (INIS)

    Qu, J.; Zhang, F.; Thakur, K.; Shi, J.J.; Zhang, J.G.; Faisal, S.; Wei, Z.J.

    2017-01-01

    Peony seed oils (PSOs) were prepared using supercritical CO2 (SC) and compared with soxhlet extraction (SE) and mechanical screw press extraction (SPE) methods. The fatty acid compositions of the oils were determined, and the physicochemical properties of the oils, including free radical-scavenging activity, α-amylase and α-glucosidase inhibition, thermal and rheological properties were evaluated. The unsaturated fatty acids in the SE oils were higher than SC and SPE oils due to the higher percentage of olefinic, allylic methylene and allylic methine protons in the SE oils. The SPE oils also displayed the highest DPPH and ABTS+ radical scavenging activity at the tested concentrations. However, the SE oils showed stronger inhibitory effects on α-amylase and α-glucosidase enzymes under in vitro conditions when compared with the other oil samples. The three oils had similar melting and crystalline point due to similar contents of fatty acids (FAs). The SC oils had a lower Ea than the others. [es

  7. Oil Depletion and the Energy Efficiency of Oil Production: The Case of California

    Directory of Open Access Journals (Sweden)

    Adam R. Brandt

    2011-10-01

    Full Text Available This study explores the impact of oil depletion on the energetic efficiency of oil extraction and refining in California. These changes are measured using energy return ratios (such as the energy return on investment, or EROI. I construct a time-varying first-order process model of energy inputs and outputs of oil extraction. The model includes factors such as oil quality, reservoir depth, enhanced recovery techniques, and water cut. This model is populated with historical data for 306 California oil fields over a 50 year period. The model focuses on the effects of resource quality decline, while technical efficiencies are modeled simply. Results indicate that the energy intensity of oil extraction in California increased significantly from 1955 to 2005. This resulted in a decline in the life-cycle EROI from 6.5 to 3.5 (measured as megajoules (MJ delivered to final consumers per MJ primary energy invested in energy extraction, transport, and refining. Most of this decline in energy returns is due to increasing need for steam-based thermal enhanced oil recovery, with secondary effects due to conventional resource depletion (e.g., increased water cut.

  8. The H-Oil process: a worldwide leader in vacuum residue hydro processing

    Energy Technology Data Exchange (ETDEWEB)

    Colyar, J.J.; Wisdom, L.I.; Koskas, A.

    1996-12-31

    The h-Oil process is a catalytic hydrocracking process which is used to convert and upgrade petroleum residua and heavy oils. This paper discusses additional background information on the H-Oil process, some of the key advances made to the process and applications for the Latin America market. 5 refs., 6 tabs.., 2 figs.

  9. Extraction and Assessment of Physicochemical Properties of Rosigold Mango (Mangifera indica Seed Kernel Oil for Bioresin Production

    Directory of Open Access Journals (Sweden)

    A. S. Sadiq

    2017-10-01

    Full Text Available This paper presents research report on extraction and assessment of physicochemical properties of Rosigold mango kernel oil. This is with a view to using the oil for bioresin production so as to mitigate some of the problems associated with petrochemical resins currently used for bulk of composite production activities. The seeds of the mango were identified and collected from the wastes discarded by marketers and consumers in Bauchi town. The Oil was obtained using soxhlet extraction with n-Hexane as solvent. The oil was characterized for yield, relative density, free fatty acid value, acid value, iodine value, and saponification value. Mean values of the characteristic parameters were: oil yield 19.6%, relative density 0.874 g/cm3, free fatty acid value 3.09 mg NaOH/g oil, acid value 6.18 mg KOH/g oil, iodine value 60.7 mg iodine/100 g oil and saponification value 143.6 mg KOH/ g oil. Analysis and comparison of these results with the physicochemical properties of palm oil, Soya bean oil and Hemp seed oil respectively, revealed that the iodine value of Rosigold mango seed kernel oil is higher than palm oil, but lower than Soya bean and Hemp seed oils respectively. Bioresin production is heavily dependent on the degree of unsaturation of the oil which is reflected by the iodine value. However, the overall results suggested that Rosigold mango seed kernel oil is suitable for bioresin production since the minimum iodine bench mark for renewable oil suitable for bioresin production is 50 mg iodine/100 g oil. The extracted oil has an added advantage in that the source (mango seed is a waste material that is readily available, affordable and sustainable in Nigeria and many other countries.

  10. Antioxidant and cytotoxic activities of the essential oil and extracts of anisosciadium orientale

    International Nuclear Information System (INIS)

    Masroorbabanari, M.; Miri, R.; Firuzi, O.

    2014-01-01

    The essential oil of Anisosciadium orientale was analyzed by gas chromatography-flame ionization detector (GC-FID) and gas chromatography-mass spectrometry (GC-MS). The essential oil (EO) was rich in monoterpene hydrocarbons: terpinolene (19.7+-2.8%, 226.4+-27.6 mg/ g EO), limonene (21.0+-1.3%, 313.3+-22.9 mg/ g EO) and myrcene (5.6+-0.50 %, 65.4+-7.2 mg/ g EO); and the phenylpropanoid myristicin (30.6+-2.3%, 438.5+-40.0 mg/ g EO). The sesquiterpene germacrene D constituted 6.1+-0.8%, 91.8+-10.6 mg/ g EO of the oil. The essential oil and the plant's methanol and 80% methanol extracts were screened for antioxidant activity and total phenol content using 2, 2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging and Folin-Ciocalteu assays, respectively. The radical scavenging activity (lower IC50s; micro g EO or the plant material (PM) /ml 10-4 M DPPH solution) was positively correlated to total phenolic content expressed as mg equivalents of gallic acid (EG) in 1 g EO or in the PM (IC50 633.2+-0.2 micro g EO /ml DPPH; 8.5+-0.2 mg EG/g EO), the methanol extracts (IC50 400.0+-0.2 micro g PM /ml DPPH; 10.3+-0.5 mg EG/g PM), and 80% methanol extracts (IC50 220.0+-0 micro g PM /ml DPPH; 15.9+-0.2 mg EG/g PM), respectively. The cytotoxic activity of the essential oil was measured on 3 human cancer cell lines including K562 (human chronic myelogenous leukemia), LS180 (human colon adenocarcinoma) and MCF-7 (human breast adenocarcinoma) cells. The IC50 values of the oil on K562, LS180 and MCF-7 cells were 396.8 +-4.9, 183.2 +- 42.8 and 159.5 +-9.0 micro g/ml, respectively (mean +- SE), while the plant extracts were not active. (author)

  11. Steam producing plant concept of 4S for oil sand extraction

    International Nuclear Information System (INIS)

    Matsuyama, Shinichiro; Nishiguchi, Youhei; Sakashita, Yoshiaki; Kasuga, Shoji; Kawashima, Masatoshi

    2009-01-01

    Plant concept of small fast reactor '4S' applying to continuous steam production for recovery of crude oil from oil sands was investigated. Assuming typical steam assisted gravity drainage (SAGD) plant whose production scale is 120,000 barrels per day of a crude oil, concept of nuclear steam supply system consisting of eight reactor modules for steam production and three reactor modules for electric generation of the 4S with a thermal rating of 135 MWt was established without any essential or significant design change from the preceding 4S with a thermal rating of 30 MWt. The 4S, provided for an oil sand extraction, will reduce greenhouse gas emission significantly, and has not much burden for development and licensing and has economic competitiveness. (author)

  12. Chemical composition and biological activities of extracts and essential oil of Boswellia dalzielii leaves.

    Science.gov (United States)

    Kohoude, Midéko Justin; Gbaguidi, Fernand; Agbani, Pierre; Ayedoun, Marc-Abel; Cazaux, Sylvie; Bouajila, Jalloul

    2017-12-01

    Boswellia dalzielii Hutch. (Burseraceae) is an aromatic plant. The leaves are used for beverage flavouring. This study investigates the chemical composition and biological activities of various extracts. The essential oil was prepared via hydrodistillation. Identification and quantification were realized via GC-MS and GC-FID. Consecutive extractions (cyclohexane, dichloromethane, ethyl acetate and methanol) were carried out and various chemical groups (phenolics, flavonoids, tannins, antocyanins and sugar) were quantified. The volatile compounds of organic extracts were identified before and after derivatization. Antioxidant, antihyperuricemia, anti-Alzheimer, anti-inflammatory and anticancer activities were evaluated. In the essential oil, 50 compounds were identified, including 3-carene (27.72%) and α-pinene (15.18%). 2,5-Dihydroxy acetophenone and β-d-xylopyranose were identified in the methanol extract. Higher phenolic (315.97 g GAE/kg dry mass) and flavonoid (37.19 g QE/kg dry mass) contents were observed in the methanol extract. The methanol extract has presented remarkable IC 50  =   6.10 mg/L for antiDPPH, 35.10 mg/L for antixanthine oxidase and 28.01 mg/L for anti-5-lipoxygenase. For acetylcholinesterase inhibition, the best IC 50 (76.20 and 67.10 mg/L) were observed, respectively, with an ethyl acetate extract and the essential oil. At 50 mg/L, the dichloromethane extract inhibited OVCAR-3 cell lines by 65.10%, while cyclohexane extract inhibited IGROV-1 cell lines by 92.60%. Biological activities were fully correlated with the chemical groups of the extracts. The ethyl acetate and methanol extracts could be considered as potential alternatives for use in dietary supplements for the prevention or treatment of diseases because of these extracts natural antioxidant, antihyperuricemic and anti-inflammatory activities.

  13. Chemical composition of the essential oil and hexane extract of Salvia chionantha and their antioxidant and anticholinesterase activities.

    Science.gov (United States)

    Tel, Gülsen; Oztürk, Mehmet; Duru, Mehmet Emin; Harmandar, Mansur; Topçu, Gülaçti

    2010-11-01

    The essential oil and methyl ester of hexane extract of Salvia chionantha Boiss. were analysed by GC and GC-MS. Totally, 54 components were detected in the essential oil and all of them were fully determined. Germacrene D (25.03%), β-caryophyllene (8.71%), spathulenol (5.86%) and α-humulene (4.82%) were identified as the major compounds. In the methylated hexane extract, 3-hydroxy hexadecanoic acid (39.39%), 3-hydroxy tetradecanoic acid (12.66%) and palmitic acid (12.02%) were the major fatty acids elucidated. The antioxidant activity of the essential oil and the hexane extract was determined by using four complementary test systems; namely, β-carotene-linoleic acid, DPPH() scavenging, ABTS(+)* scavenging, and CUPRAC assays. In β-carotene-linoleic acid assay, the extract showed 81.2±0.1% lipid peroxidation inhibition at 0.8 mg/mL concentration, while in ABTS(+)* assay the essential oil exhibited 77.4±0.5% inhibition at same concentration. Since, acetylcholinesterase and butyrylcholinesterase enzymes are taking place in pathogenesis of Alzheimer's disease, in vitro anticholinesterase activity of the essential oil and the extract was also studied spectrophotometrically. At 0.5mg/mL concentration, the essential oil showed moderate acetylcholinesterase (56.7±1.9%) and butyrylcholinesterase (41.7±2.9%) inhibitory activity, while the extract was only exhibited activity (63.1±0.8%) against butyrylcholinesterase enzyme. Hence, the essential oil may be useful as a moderate anticholinesterase agent, particularly against acetylcholinesterase. Copyright © 2010 Elsevier Ltd. All rights reserved.

  14. Changes during storage of quality parameters and in vitro antioxidant activity of extra virgin monovarietal oils obtained with two extraction technologies.

    Science.gov (United States)

    Fadda, C; Del Caro, A; Sanguinetti, A M; Urgeghe, P P; Vacca, V; Arca, P P; Piga, A

    2012-10-01

    Extraction technology has a great effect on quality of olive oils. This paper studied 18 months of storage of two Sardinian extra virgin monovarietal oils obtained with a traditional and with a low oxidative stress technology. Oil samples were subjected to the following chemical analyses: acidity, peroxide value, ultraviolet light absorption K₂₃₂ and K₂₇₀, carotenoids, chlorophylls, tocopherols and total polyphenols. The antioxidant capacity of oils, polyphenol extract and oil extract (remaining after polyphenol extraction) was also determined as radical scavenging activity. The results show that both extraction technologies resulted in minor changes in legal and quality indices during storage, due surely to the high quality of the oils as well as to the very good storage conditions used. Oils obtained with the low oxidative stress technology showed lower peroxide value and acidity and resulted in up to 103% higher total polyphenol content as well as increased radical-scavenging activity, with respect to oils obtained with the traditional technology. Copyright © 2012 Elsevier Ltd. All rights reserved.

  15. antibacterial activities of the volatile oil and aqueous extract of ...

    African Journals Online (AJOL)

    The volatile oil of Murraya keonigii was active against Staphylococcus epidemidis, S. aureus, and Streptococcus specie while the aqueous extract was not active. Key Words: Murraya koenigii, Rutaceae, antibacterial activity. Nig. J. Nat. Prod. And Med. Vol.2 1998: 44-45 ...

  16. Extraction of essential oils from native plants and algae from the coast of Peniche (Portugal: antimicrobial and antioxidant activity.

    Directory of Open Access Journals (Sweden)

    Clélia Neves Afonso

    2014-06-01

    Full Text Available Coastal areas are highly complex and dynamic ecosystem of interface between land, sea and atmosphere, which also suffer biotic influences. These areas play several important ecological functions, and here we can find an enormous biodiversity. The coastline of Portugal features a high number of endemic flora and vegetation with the potential to provide functional compounds that may provide physiological benefits at nutritional and therapeutic levels, as sources of bioactive substances with antimicrobial, antioxidant, antifungal, antitumalr and anti-inflammatory activity. Among these compounds, we find essential oils, also known as volatile oils, which are a result of secondary metabolism of aromatic plants, containing a large number of substances with varied chemical composition that can be obtained by different methods of extraction. The aim of this study was to extract essential oils of native plants and seaweeds from the coast of Peniche by hydrodistillation in Clevenger apparatus, with optimization of the purification process. Extracted essential oils were tested as to their ability as antibacterial and antifungal agents, and also as antioxidants. The plants studied for this purpose were Inula chritmoides L., Juniperus phoenicea subsp. turbinata (Guss. Nyman, Daucus carota spp. halophilus and the seaweeds Fucus spiralis L., Codium tomentosum Stackhouse, Stypocaulon scoparium (Linnaeus Kützing and Plocamium cartilagineum (Linnaeus P.S.Dixon. The antimicrobial ability was tested in two bacteria species, Bacillus subtilis and Escherichia coli and in the yeast Saccharomyces cerevisiae, using standard procedures. The antioxidant potential was evaluated and from the results obtained, we can conclude that the essential oils extracted by the hydrodistillation method of plants and algae contain bioactive compounds present in its constitution with interesting bio-activity that can offer significant benefits and biotechnological relevance.

  17. Supercritical extraction of pupunha (Guilielma speciosa oil in a fixed bed using carbon dioxide

    Directory of Open Access Journals (Sweden)

    Araújo M.E.

    2000-01-01

    Full Text Available The pupunha (Guilielma speciosa is the fruit of a palm tree typical of the Brazilian Northern region, whose stem is used as a source of heart of palm. The fruit, which is about 65% pulp, is a source of oil and carotenes. In the present work, an analysis of the kinetics of supercritical extraction of oil from the pupunha pulp is presented. Carbon dioxide was used as solvent. The extractions were carried out at 25 MPa and 323 K and 30 MPa and 318 K. The chemical composition of the extracts in terms of fatty acids was determined by gas chromatography. The amount of oleic acid, a saturated fatty acid, in the CO2 extracts was larger than that in the extract obtained with hexane. The overall extraction curves were modeled using the single-parameter model proposed in the literature to describe the desorption of toluene from activated coal.

  18. Comparison of solvent extraction and solid-phase extraction for the determination of polychlorinated biphenyls in transformer oil.

    Science.gov (United States)

    Mahindrakar, A N; Chandra, S; Shinde, L P

    2014-01-01

    Solid-phase extraction (SPE) of nine polychlorinated biphenyls (PCBs) from transformer oil samples was evaluated using octadecyl (CI8)-bonded porous silica. The efficiency of SPE of these PCBs was compared with those obtained by solvent extraction with DMSO and hexane. Average recoveries exceeding 95% for these PCBs were obtained via the SPE method using small cartridges containing 100mg of 40 pm CI8-bonded porous silica. The average recovery by solvent extraction with DMSO and hexane exceeded 83%. It was concluded that the recoveries and precision for the solvent extraction of PCBs were poorer than those for the SPE. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. Process for treating oil-chalk

    Energy Technology Data Exchange (ETDEWEB)

    1925-10-20

    A process for treating oil-chalk or similar oil-containing minerals is characterized in that the material is treated in a stream of air diluted with indifferent gases at a temperature of about 150/sup 0/ to 160/sup 0/C.

  20. A detailed analysis of the productivity performance of oil and gas extraction in Canada

    International Nuclear Information System (INIS)

    Bradley, C.; Sharpe, A.

    2009-09-01

    The productivity and performance of oil and gas extraction in Canada has been poor over the last few years. Various input estimates show that labour productivity dropped by 8.23 per cent per year between 2000 and 2007. Hours worked grew 108.0 per cent while real gross domestic product (GDP) increased by 14.1 per cent. Oil and gas extraction accounted for 6.2 per cent of aggregate labour productivity growth in Canada between 1987 and 2006. Relative real oil and gas prices also increased significantly during this period. However, declining capital intensity, higher output prices and lagging innovation and technological progress led to declines in labour, capital, and total factor productivity in the oil and gas extraction sector during this period. Higher prices translated into a falling capital-labour ratio. Productivity growth suffered as a result of greater inefficiencies in operations. It was concluded that the deceleration in labour productivity growth after 2000 indicates a slower rate of increase in living standards despite the fact that higher commodity prices have increased the real income of Canadians. 90 refs., 6 tabs., 20 figs.

  1. Wheat germ oil extracted by supercritical carbon dioxide with ethanol: Fatty acid composition

    Directory of Open Access Journals (Sweden)

    Parczewska-Plesnar, B.

    2016-09-01

    Full Text Available In this work, supercritical fluid extraction (SFE using CO2 with ethanol as entrainer was performed at a temperature of 40 oC under a pressure of 21 MPa. For comparison, a similar extraction without the entrainer was carried out. The extraction yield of wheat germ using supercritical CO2 with ethanol was slightly higher (10.7 wt% than that of extraction without the entrainer (9.9 wt%. Fractions of SFE extracts were collected separately during the experiments and the composition of fatty acids in each fraction was analyzed. The SFE extracted oils were rich (63.4-71.3% in the most valuable polyunsaturated fatty acids (PUFA and their content in all collected fractions was approximately constant. Similar PUFA contents were found in the reference samples of oils extracted by n-hexane (66.2-67.0%, while the commercial cold-pressed oil contained significantly less PUFA (60.2%. These results show a higher nutritional value of the oil obtained by extraction with supercritical CO2 than cold pressed oil which is generally considered to be very valuable.En este trabajo, la extracción con fluidos supercríticos (SFE usando CO2 con etanol como agente de arrastre se realizó a 40 °C bajo una presión de 21 MPa. Se ha llevado a cabo la comparación con una extracción similar sin agente de arrastre. El rendimiento de la extracción de germen de trigo usando CO2 supercrítico con etanol fue ligeramente mayor (10,7% en peso que la de extracción sin agente de arrastre (9,9% en peso. Se recogieron por separado fracciones de extractos SFE durante los experimentos y se analizó la composición de ácidos grasos en cada fracción. Los aceites extraídos mediante SFE eran ricos en los ácidos grasos poliinsaturados más valiosos (63,4-71,3%, (PUFA y su contenido en todas las fracciones recogidas fue aproximadamente constante. Un contenido similar de PUFA fueron encontrados en muestras de referencia de los aceites extraídos con n-hexano (66,2-67,0%, mientras que el

  2. Antioxidant effcacy of unripe banana (Musa acuminata Colla) peel extracts in sunflower oil during accelerated storage.

    Science.gov (United States)

    Ling, Stella Sye Chee; Chang, Sui Kiat; Sia, Winne Chiaw Mei; Yim, Hip Seng

    2015-01-01

    Sunflower oil is prone to oxidation during storage time, leading to production of toxic compounds that might affect human health. Synthetic antioxidants are used to prevent lipid oxidation. Spreading interest in the replacement of synthetic food antioxidants by natural ones has fostered research on fruit and vegetables for new antioxidants. In this study, the efficacy of unripe banana peel extracts (100, 200 and 300 ppm)  in stabilizing sunflower oil was tested under accelerated storage (65°C) for a period of 24 days. BHA and α-tocopherol served as comparative standards besides the control. Established parameters such as peroxide value (PV), iodine value (IV), p-anisidine value (p-AnV), total oxidation value (TOTOX), thiobarbituric acid reactive substances (TBARS) and free fatty acid (FFA) content were used to assess the extent of oil deterioration. After 24 days storage at 65°C, sunflower oil containing 200 and 300 ppm extract of unripe banana peel showed significantly lower PV and TOTOX compared to BHA and α-tocopherol. TBARS, p-AnV and FFA values of sunflower oil containing 200 and 300 ppm of unripe banana peel extract exhibited comparable inhibitory effects with BHA. Unripe banana peel extract at 200 and 300 ppm demonstrated inhibitory effect against both primary and secondary oxidation up to 24 days under accelerated storage conditions. Unripe banana peel extract may be used as a potential source of natural antioxidants in the application of food industry to suppress lipid oxidation.

  3. Performance Analysis of Compositional and Modified Black-Oil Models For a Gas Lift Process Analyse des performances de modèles black-oil pour le procédé d’extraction par injection de gaz

    Directory of Open Access Journals (Sweden)

    Mahmudi M.

    2013-03-01

    Full Text Available Artificial gas lift is frequently used to boost production rate of mature oil fields. An integrated mathematical model was developed in order to track the spatial and temporal changes in various components of the continuous gas lift process. The computational demand for solving the comprehensive gas lift model highly depends on the thermodynamic treatment of the hydrocarbon fluids involved. A full compositional treatment using an equation of state provides the most accurate results but at a high computational cost. The results of this article showed that the computational cost can be halved without sacrificing accuracy by using reduced parameter stability and flash calculation procedures. It was also demonstrated that a Modified Black-Oil treatment of the fluids can provide reasonable accuracy at a much-reduced computational cost. The Modified Black-Oil treatment provides a valuable tool when the model has to be solved many hundreds of times to find the optimal combination of the gas lift parameters. Les procédés artificiels d’extraction par injection de gaz sont utilisés pour améliorer le taux de récupération des champs pétroliers matures. Un modèle mathématique intégré a été développé pour détecter de faibles changements temporels et spatiaux dans plusieurs composants des procédés continus d’extraction par injection de gaz. La solution numérique utilisée pour résoudre le modèle du procédé d’extraction dépend fortement du comportement thermodynamique des hydrocarbures impliqués. Un traitement complet de la composition utilisant une équation d’état offre les résultats les plus précis, mais à un coût de calcul très élevé. Les résultats de nos travaux de recherche montrent que l’implication des paramètres de stabilité et des procédures de calcul flash, peut diviser par deux le coût du calcul tout en gardant la précision attendue. Ces travaux montrent que la précision admissible peut être

  4. Coal tar phototherapy for psoriasis reevaluated: erythemogenic versus suberythemogenic ultraviolet with a tar extract in oil and crude coal tar

    International Nuclear Information System (INIS)

    Lowe, N.J.; Wortzman, M.S.; Breeding, J.; Koudsi, H.; Taylor, L.

    1983-01-01

    Recent studies have questioned the therapeutic value of coal tar versus ultraviolet (UV) radiation and their relative necessity in phototherapy for psoriasis. In this investigation, different aspects of tar phototherapy have been studied in single-blind bilateral paired comparison studies. The effects of 1% crude coal tar were compared with those of petrolatum in conjunction with erythemogenic and suberythemogenic doses of ultraviolet light (UVB) using a FS72 sunlamp tubed cabinet. Crude coal tar was clinically superior to petrolatum with suberythemogenic ultraviolet. With the erythemogenic UVB, petrolatum was equal in efficacy to crude coal tar. Suberythemogenic UVB was also used adjunctively to compare the effects of a 5% concentration of a tar extract in an oil base to 5% crude coal tar in petrolatum or the oil base without tar. The tar extract in oil plus suberythemogenic UVB produced significantly more rapid improvement than the oil base plus UVB. The direct bilateral comparison of equal concentrations of tar extract in oil base versus crude coal tar in petrolatum in a suberythemogenic UV photo regimen revealed no statistical differences between treatments. In a study comparing tar extract in oil and the oil base without ultraviolet radiation, the tar extract in oil side responded more rapidly

  5. Extraction and characterization of mandarin essential oil obtained from agroindustrial residues

    International Nuclear Information System (INIS)

    Navarrete, Carolina; Gil, Jesus; Durango, Diego; Garcia, Carlos

    2010-01-01

    In recent years, citrus national agroindustries have shown a significant momentum, led by the market expansion of fruit derivatives. This activity has resulted in the generation of large amounts of waste, which could have a potential as starting material for the development of commercial products with high added value such as essential oils (EO), fixed oils, and fibres among others. The EO have a strong demand in the food industry, pharmaceuticals, and cosmetics. This paper describes the extraction and characterization of mandarin EO obtained through steam distillation, of agroindustrial waste. The effect of vapour pressure, thickness, and the number of layers of plant material, were evaluated on the yield and quality of EO. The operating conditions were adjusted in accordance to the design characteristics of the extraction plant of a local company.

  6. Microdialysis as a New Technique for Extracting Phenolic Compounds from Extra Virgin Olive Oil.

    Science.gov (United States)

    Bazzu, Gianfranco; Molinu, Maria Giovanna; Dore, Antonio; Serra, Pier Andrea

    2017-03-01

    The amount and composition of the phenolic components play a major role in determining the quality of olive oil. The traditional liquid-liquid extraction (LLE) method requires a time-consuming sample preparation to obtain the "phenolic profile" of extra virgin olive oil (EVOO). This study aimed to develop a microdialysis extraction (MDE) as an alternative to the LLE method to evaluate the phenolic components of EVOO. To this purpose, a microdialysis device and dialysis procedure were developed. "Dynamic-oil" microdialysis was performed using an extracting solution (80:20 methanol/water) flow rate of 2 μL min -1 and a constant EVOO stream of 4 μL min -1 . The results indicated a strong positive correlation between MDE and the LLE method, providing a very similar phenolic profile obtained with traditional LLE. In conclusion, the MDE approach, easier and quicker in comparison to LLE, provided a reliable procedure to determine the phenolic components used as a marker of the quality and traceability of EVOO.

  7. Quality assessment of Moringa concanensis seed oil extracted through solvent and aqueous-enzymatic techniques

    Directory of Open Access Journals (Sweden)

    Anwar, Farooq

    2008-03-01

    Full Text Available The composition and quality of the M. concanensis seed oil extracted through an aqueous-enzyme-assisted technique, using three commercial enzyme-mixtures (Natuzyme, Kemzyme, and Feedzyme was compared to those of the control-, (without enzymes and solvent-extracted oils. Aqueous enzyme-extracted M.concanensis seed oil content ranged from 23.54 to 27.46% and was significantly (P 0.05 variation in the contents of fiber and ash within the three extraction methods. However, the protein content of the meal obtained through the aqueous-enzyme and control methods was significantly (P M. concanensis seed oils extracted using the three methods. The specific extinctions at 232 and 270 nm, peroxide value, p-anisidine, free fatty acid contents and color values of the aqueous-enzyme-extracted oil were found to be lower than that of solvent-extracted oil and thus revealed good quality. The oils extracted through the three methods exhibited no significant (P En este estudio se compara la composición y la calidad del aceite de semilla de M. concanensis extraído mediante enzimas, utilizando tres enzimas comerciales (Natuzyme, Kemzyme, y Feedzyme con las de un control extraído sin enzimas y con las del aceite extraído con disolvente. El contenido en aceites de las semilla extraídas con enzimas osciló entre 23,54 a 27,46% y fue significativamente más elevado (P 0,05 en el contenido de fibra y ceniza para los tres métodos de la extracción. Sin embargo, el contenido proteínico de la harina obtenido por métodos enzimáticos y el control sin enzimas fue significativamente menor (P < 0,05 que el de la harina obtenida después de la extracción por disolvente. Las diferencias en el índice de yodo (67.1-68.0 g /100 g of oil, densidad en 24 °C (0,865-0,866 g/mL, índice de refracción a 40 °C (1,4622-1,4627 y fracción insaponificable (0,69-0,76 % no fueron significativamente diferentes para ninguna de las técnicas de extracción. Las extinciones espec

  8. Choice of solvent extraction technique affects fatty acid composition of pistachio (Pistacia vera L.) oil.

    Science.gov (United States)

    Abdolshahi, Anna; Majd, Mojtaba Heydari; Rad, Javad Sharifi; Taheri, Mehrdad; Shabani, Aliakbar; Teixeira da Silva, Jaime A

    2015-04-01

    Pistachio (Pistacia vera L.) oil has important nutritional and therapeutic properties because of its high concentration of essential fatty acids. The extraction method used to obtain natural compounds from raw material is critical for product quality, in particular to protect nutritional value. This study compared the fatty acid composition of pistachio oil extracted by two conventional procedures, Soxhlet extraction and maceration, analyzed by a gas chromatography-flame ionization detector (GC-FID). Four solvents with different polarities were tested: n-hexane (Hx), dichloromethane (DCM), ethyl acetate (EtAc) and ethanol (EtOH). The highest unsaturated fatty acid content (88.493 %) was obtained by Soxhlet extraction with EtAc. The Soxhlet method extracted the most oleic and linolenic acids (51.99 % and 0.385 %, respectively) although a higher concentration (36.32 %) of linoleic acid was extracted by maceration.

  9. The extraction of uranium from wet process phosphoric acid using a liquid surfactant membrane system

    International Nuclear Information System (INIS)

    Dickens, N.; Davies, G.A.

    1984-01-01

    A liquid membrane extraction process is examined for the extraction of uranium from wet process phosphoric acid. Uranium is present in the acid in concentrations up to 100 ppm which in principle makes it ideal for treatment with a membrane process. The membrane system studied is based on extraction using DEHPA-TOPO reagents which are contained within the organic phase of a water in oil emulsion. Formulations of the emulsion membrane system have been studied, the limitations of acid temperature, P 2 O 5 concentration and solid dispersed impurities in the acid have been studied in laboratory batch experiments and in a continuous pilot plant unit capable of treating 5l of concentrated acid per minute. Data from the pilot plant work has been used to develop a flowsheet for a commercial unit based on this process. (author)

  10. Optimization of physicochemical and textural properties of pizza cheese fortified with soybean oil and carrot extract.

    Science.gov (United States)

    Motevalizadeh, Ehsan; Mortazavi, Seyed Ali; Milani, Elnaz; Hooshmand-Dalir, Moosa Al-Reza

    2018-03-01

    Response surface methodology (RSM) was used to optimize pizza cheese containing carrot extract. The effects of two important independent variables including soybean oil (5%-20%) and carrot extract (5%-20%) were studied on physicochemical and textural properties of pizza cheese containing carrot extract. According to the results, RSM was successfully used for optimizing formulation of pizza cheese containing carrot juice. Results of this study revealed that oil (A), carrot (B), AB, square term of carrot (B 2 ), B, AB, square term of oil (A 2 ), B 2 , AB, AB, A 2 B, A 2 , A 2 , A, A 2 , A 2 , AB, and AB 2 had the most effect on moisture, acidity, stretch, L*, a*, b*, hardness, meltability, springiness, peroxide value (PV), cohesiveness, chewiness, gumminess, fracture force, adhesiveness force, stiffness, flavor, and overall acceptability, respectively. A formulation upon 20% oil and 10.88% carrot extract was found as the optimal formulation for pizza cheese containing carrot extract. At the optimal formulation, PV, L*, a*, b*, meltability, stretch, cohesiveness, springiness, gumminess, chewiness, adhesive force, flavor, texture, and overall acceptability at the optimum formulation were measured 2.23, 82.51, -3.69, 18.05, 17.86, 85.61, 0.41, 7.874, 23.7, 0.27, 0.61, 3.50, 3.95, and 3.65, respectively.

  11. Process water treatment in Canada's oil sands industry : 1 : target pollutants and treatment objectives

    International Nuclear Information System (INIS)

    Allen, E.W.

    2008-01-01

    The continuous recycling of tailings pond water in the oil sands industry has contributed to an overall decline in water quality used for bitumen recovery, general water consumption, and remedial activities. This paper reviewed process water quality and toxicity data from 2 long-term oil sands operations. The aim of the study was to determine potential roles for water treatment and provide benchmarks for the selection of candidate water treatment technologies in the oil sands region of Alberta. An overview of the oil sands industry was provided as well as details of bitumen recovery processes. The study examined target pollutants and exceedances identified in environmental and industrial water quality guidelines. The study demonstrated that the salinity of tailings pond water increased at a rate of 75 mg per litre per year between 1980 and 2001. Increases in hardness, chloride, ammonia, and sulphates were also noted. Naphthenic acids released during bitumen extraction activities were determined as the primary cause of tailings pond water toxicity. A summary of recent studies on experimental reclamation ponds and treatment wetlands in the oil sands region was included. 19 refs., 4 tabs., 11 figs

  12. The optimization of essential oils supercritical CO2 extraction from Lavandula hybrida through static-dynamic steps procedure and semi-continuous technique using response surface method

    Science.gov (United States)

    Kamali, Hossein; Aminimoghadamfarouj, Noushin; Golmakani, Ebrahim; Nematollahi, Alireza

    2015-01-01

    Aim: The aim of this study was to examine and evaluate crucial variables in essential oils extraction process from Lavandula hybrida through static-dynamic and semi-continuous techniques using response surface method. Materials and Methods: Essential oil components were extracted from Lavandula hybrida (Lavandin) flowers using supercritical carbon dioxide via static-dynamic steps (SDS) procedure, and semi-continuous (SC) technique. Results: Using response surface method the optimum extraction yield (4.768%) was obtained via SDS at 108.7 bar, 48.5°C, 120 min (static: 8×15), 24 min (dynamic: 8×3 min) in contrast to the 4.620% extraction yield for the SC at 111.6 bar, 49.2°C, 14 min (static), 121.1 min (dynamic). Conclusion: The results indicated that a substantial reduction (81.56%) solvent usage (kg CO2/g oil) is observed in the SDS method versus the conventional SC method. PMID:25598636

  13. Integrated extraction and anaerobic digestion process for recovery of nutraceuticals and biogas from pomegranate marcs

    Science.gov (United States)

    Pomegranate marc (PM), a by-product from pomegranate juice processing, has not been effectively utilized. The objectives of this study were to (1) determine the yields and properties of antioxidants (henceforth referring to total phenolics in terms of tannic acid equivalent) and oil extracted from v...

  14. In Vitro Antibacterial Activity of Several Plant Extracts and Oils against Some Gram-Negative Bacteria

    Directory of Open Access Journals (Sweden)

    Ayman Al-Mariri

    2014-01-01

    Full Text Available Background: Medicinal plants are considered new resources for producing agents that could act as alternatives to antibiotics in the treatment of antibiotic-resistant bacteria. The aim of this study was to evaluate the antibacterial activity of 28 plant extracts and oils against four Gram-negative bacterial species. Methods: Experimental, in vitro, evaluation of the activities of 28 plant extracts and oils as well as some antibiotics against E. coli O157:H7, Yersinia enterocolitica O9, Proteus spp., and Klebsiella pneumoniae was performed. The activity against 15 isolates of each bacterium was determined by disc diffusion method at a concentration of 5%. Microdilution susceptibility assay was used in order to determine the minimal inhibitory concentrations (MICs of the plant extracts, oils, and antibiotics. Results: Among the evaluated herbs, only Origanum syriacum L., Thymus syriacus Boiss., Syzygium aromaticum L., Juniperus foetidissima Wild, Allium sativum L., Myristica fragrans Houtt, and Cinnamomum zeylanicum L. essential oils and Laurus nobilis L. plant extract showed anti-bacterial activity. The MIC50 values of these products against the Gram-negative organisms varied from 1.5 (Proteus spp. and K. pneumoniae( and 6.25 µl/ml (Yersinia enterocolitica O9 to 12.5 µl/ml (E. coli O:157. Conclusion: Among the studied essential oils, O. syriacum L., T. syriacus Boiss., C. zeylanicum L., and S. aromaticum L. essential oils were the most effective. Moreover, Cephalosporin and Ciprofloxacin were the most effective antibiotics against almost all the studied bacteria. Therefore, O. syriacum L., T. syriacus Boiss., C. zeylanicum L., and S. aromaticum L. could act as bactericidal agents against Gram-negative bacteria.

  15. Rapid detection of Ganoderma-infected oil palms by microwave ergosterol extraction with HPLC and TLC.

    Science.gov (United States)

    Muniroh, M S; Sariah, M; Zainal Abidin, M A; Lima, N; Paterson, R R M

    2014-05-01

    Detection of basal stem rot (BSR) by Ganoderma of oil palms was based on foliar symptoms and production of basidiomata. Enzyme-Linked Immunosorbent Assays-Polyclonal Antibody (ELISA-PAB) and PCR have been proposed as early detection methods for the disease. These techniques are complex, time consuming and have accuracy limitations. An ergosterol method was developed which correlated well with the degree of infection in oil palms, including samples growing in plantations. However, the method was capable of being optimised. This current study was designed to develop a simpler, more rapid and efficient ergosterol method with utility in the field that involved the use of microwave extraction. The optimised procedure involved extracting a small amount of Ganoderma, or Ganoderma-infected oil palm suspended in low volumes of solvent followed by irradiation in a conventional microwave oven at 70°C and medium high power for 30s, resulting in simultaneous extraction and saponification. Ergosterol was detected by thin layer chromatography (TLC) and quantified using high performance liquid chromatography with diode array detection. The TLC method was novel and provided a simple, inexpensive method with utility in the field. The new method was particularly effective at extracting high yields of ergosterol from infected oil palm and enables rapid analysis of field samples on site, allowing infected oil palms to be treated or culled very rapidly. Some limitations of the method are discussed herein. The procedures lend themselves to controlling the disease more effectively and allowing more effective use of land currently employed to grow oil palms, thereby reducing pressure to develop new plantations. Copyright © 2014 Elsevier B.V. All rights reserved.

  16. Application of cavitation system to accelerate aqueous enzymatic extraction of seed oil from Cucurbita pepo L. and evaluation of hypoglycemic effect.

    Science.gov (United States)

    Li, Xiao-Juan; Li, Zhu-Gang; Wang, Xun; Han, Jun-Yan; Zhang, Bo; Fu, Yu-Jie; Zhao, Chun-Jian

    2016-12-01

    Cavitation-accelerated aqueous enzymatic extraction (CAEE) of seed oil from Cucurbita pepo was performed. An enzyme cocktail comprised of cellulose, pectinase and proteinase can work synergistically in releasing the oil. The CAEE extraction conditions were optimized by a Plackett-Burman design followed by a central composite methodology. A maximal extraction yield of 58.06% was achieved under optimal conditions of vacuum degree -0.07, enzyme amount 1.05% and extraction time 69min. As compared to soxhlet extraction (SE)-derived oil, CAEE-derived oil exhibited similar physical properties and better oxidation stability. In addition, chemical composition analyzing showed that the content of linoleic acid obtained by CAEE (47.67%) was higher than that of SE (44.51%). Moreover, the IC50 of oil obtained by CAEE and SE, as measured by α-amylase inhibition assay, were 40.68μg/mL and 45.46μg/mL. All results suggest that CAEE represents an excellent alternative protocol for production of oil from oil-bearing materials. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Obtaining bixin from semi-defatted annatto seeds by a mechanical method and solvent extraction: Process integration and economic evaluation.

    Science.gov (United States)

    Alcázar-Alay, Sylvia C; Osorio-Tobón, J Felipe; Forster-Carneiro, Tânia; Meireles, M Angela A

    2017-09-01

    This work involves the application of physical separation methods to concentrate the pigment of semi-defatted annatto seeds, a noble vegetal biomass rich in bixin pigments. Semi-defatted annatto seeds are the residue produced after the extraction of the lipid fraction from annatto seeds using supercritical fluid extraction (SFE). Semi-defatted annatto seeds are use in this work due to three important reasons: i) previous lipid extraction is necessary to recovery the tocotrienol-rich oil present in the annatto seeds, ii) an initial removal of the oil via SFE process favors bixin separation and iii) the cost of raw material is null. Physical methods including i) the mechanical fractionation method and ii) an integrated process of mechanical fractionation method and low-pressure solvent extraction (LPSE) were studied. The integrated process was proposed for processing two different semi-defatted annatto materials denoted Batches 1 and 2. The cost of manufacture (COM) was calculated for two different production scales (5 and 50L) considering the integrated process vs. only the mechanical fractionation method. The integrated process showed a significantly higher COM than mechanical fractionation method. This work suggests that mechanical fractionation method is an adequate and low-cost process to obtain a rich-pigment product from semi-defatted annatto seeds. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Effect of drying and co-matrix addition on the yield and quality of supercritical CO₂ extracted pumpkin (Cucurbita moschata Duch.) oil.

    Science.gov (United States)

    Durante, Miriana; Lenucci, Marcello S; D'Amico, Leone; Piro, Gabriella; Mita, Giovanni

    2014-04-01

    In this work a process for obtaining high vitamin E and carotenoid yields by supercritical carbon dioxide (SC-CO₂) extraction from pumpkin (Cucurbita moschata Duch.) is described. The results show that the use of a vacuum oven-dried [residual moisture (∼8%)] and milled (70 mesh sieve) pumpkin flesh matrix increased SC-CO₂ extraction yields of total vitamin E and carotenoids of ∼12.0- and ∼8.5-fold, respectively, with respect to the use of a freeze-dried and milled flesh matrix. The addition of milled (35 mesh) pumpkin seeds as co-matrix (1:1, w/w) allowed a further ∼1.6-fold increase in carotenoid yield, besides to a valuable enrichment of the extracted oil in vitamin E (274 mg/100 g oil) and polyunsaturated fatty acids. These findings encourage further studies in order to scale up the process for possible industrial production of high quality bioactive ingredients from pumpkin useful in functional food or cosmeceutical formulation. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. using Supercritical Fluid Extraction

    African Journals Online (AJOL)

    Methods: Supercritical CO2 extraction technology was adopted in this experiment to study the process of extraction of volatile oil from Polygonatum odoratum while gas chromatograph-mass spectrometer ..... Saponin rich fractions from.

  20. Essential oils and hydrophilic extracts from the leaves and flowers of Succisa pratensis Moench. and their biological activity.

    Science.gov (United States)

    Witkowska-Banaszczak, Ewa; Długaszewska, Jolanta

    2017-11-01

    This study was undertaken to evaluate the antioxidant activity of methanol and water extracts from Succisa pratensis Moench (Dipsacaceae) leaves and flowers as well as the chemical composition of the essential oils found in them and the antimicrobial activity of the oils and extracts thereof. The essential oils from S. pratensis leaves and flowers were analysed by the GC-MS. The total phenolic content was determined with Folin-Ciocalteu, that of flavonoids with aluminium chloride and that of phenolic acids with Arnov's reagent. The antioxidant activity was investigated by the DPPH radical scavenging assay. Antimicrobial activity was studied in vitro against G-positive and G-negative bacteria, and fungi using disc diffusion and broth microdilution methods. Eighty-six components of the leaf essential oil and 50 of the flower essential oil were identified. The main components of the leaf essential oil were 2-hexyl-1-octanol (5.76%) and heptacosane (5.53%), whereas hexadecanoic acid (16.10%), 8-octadecen-1-ol acetate (9.86%), methyl linolenate (8.58%), pentacosane (6.63%) and heptacosane (5.50%) were found in the flower essential oil. The essential oils exerted high antimicrobial activity (range: 0.11 to >3.44mg/ml) against the following bacteria: Pseudomonas aeruginosa, Staphylococcus aureus and fungi: Trichophyton mentagrophytes, Candida albicans, whereas the methanol and water extracts showed moderate or weak activity. The strongest antioxidant activity was shown by methanol extracts from S. pratensis leaves, IC 50 = 0.09 mg/ml. There was a positive correlation between the total phenolic content and the antimicrobial activity, while for the antioxidant effect, it was not observed. The results suggest great antibacterial activity of the oils and high antioxidant activity of the methanol extract and may justify the application in treating infections. © 2017 Royal Pharmaceutical Society.