Energy Technology Data Exchange (ETDEWEB)

A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to ...

International Nuclear Information System (INIS)

Recent data on resistance of modern corrosion-resistant austenitic-ferritic steels to different types of corrosion are generalized. It is shown that these steels are characterized by high resistance to general corrosion in acid, alkali, chloride and other solutions, are not inclined to intercrystalline, pitting and crevice corrosion and are noted for high resistance to corrosion cracking and corrosion fatigue. All this is combined with technological and economical effectiveness. It is advisible to use these steels instead of highly-alloyed and expensive steels and alloys in chemical, power and other industries. 59 refs.; 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

Stainless steels can be nitrided at temperatures {<=}400 C to increase their hardness and wear resistance without a decreasing of their excellent corrosion resistance. Structure and properties of the surface layers produced by plasma nitriding and plasma immersion ion implantation in this temperature range were tested. There are negligible differences in the structure of the produced surface layers in spite of different interaction principles of the used technologies. However there are clear differences between the case of different steels. The case of ferritic chromium steels mainly consists of {epsilon}-nitride. Whereas the cases of austenitic and ferritic austenitic steels are characterized by expanded austenite. The corrosion resistance of the steels is reduced by nitriding only, if evident CrN-formation occurs. (orig.) 11 refs.

International Nuclear Information System (INIS)

Because of their austenitic-ferritic microstructures, duplex stainless steels offer a good combination of mechanical and corrosion resistance properties. However, heat treatments can lower the mechanical strength of these stainless steels as well as render them susceptible to intergranular corrosion (IGC) and pitting corrosion. In this study, a low-carbon (0.02%) duplex stainless steel is subjected to various heat treatments at 450 to 950 C for 30 min to 10 h. The heat-treated samples than undergo ASTM IGC and pitting corrosion tests, and the results are correlated with the microstructures obtained after each heat treatment. In the absence of Cr_2_3C_6 precipitation, #sigma#-phase precipitates render this duplex stainless steel susceptible to IGC and pitting corrosion. Even submicroscopic #sigma#-phase precipitates are deleterious for IGC resistance. Longer-duration heat treatments ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behaviour of passive films formed on one austenitic stainless steel (AISI 304) and one ferritic stainless steel (AISI 446) in solutions with pH between 0.6 and 8.4 was studied by capacitance measurements and photocurrent spectroscopy. Compositional characterization of the passive films was done by X-ray photoelectron spectroscopy. The capacitance increases with decreasing pH. Doping densities evaluated from Mott-Schottky plots are in the range 2-6 x 10{sup 20} cm{sup -3} and increased with the pH in the neutral/alkaline range while in pH 0.6, values above 10{sup 21} cm{sup -3} were found. The bandgap energy indicates two transitions, at 2.5-2.8 and 3.2 eV. The analytical data reveal that, as the pH increased, the films become enriched in Fe(II) and Fe(III), whereas the Cr(III) gradually decreases. The films formed at very low pH had a behaviour that contrasts with that of the films formed in the ...

Energy Technology Data Exchange (ETDEWEB)

Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation of mechanical ...

Energy Technology Data Exchange (ETDEWEB)

The effect of molybdenum on the electronic structure of the passive films formed on ferritic (Fe-Cr and Fe-Cr-Mo) stainless steels is examined by capacitance and photoelectrochemical measurements. The capacitance study is supported by a mathematical analysis of the Schottky barrier developed at the semiconductor-electrolyte interface in the case of a semiconductor with multiple bulk electronic states in the bandgap. The numerical simulations, based on the more general Mott-Schottky relation proposed, are in good agreement with the experimental results. It can be concluded that the capacitance behavior of the passive films is related to the contributions of a shallow donor level very close to the conduction band and a deep donor level at about 0.4 eV below the conduction band. The addition of molybdenum decreases the donor density of the deep level. Photoeffects observed for subbandgap photon energies reveal that this deep donor level behaves ...

Energy Technology Data Exchange (ETDEWEB)

Described herein are effects of nitrogen dissolved in steel on passivity and pitting corrosion, as one of the major corrosion phenomena observed in stainless steel. Mechanisms involved in controlling pitting corrosion by nitrogen are also discussed. Nitrogen contained in austenic stainless steel is concentrated in the surface area, in particular in the vicinity of the interface between the passive film and metal matrix. Nitrogen tends to decrease critical current density in an acid, when it is added to steel of high critical current density (approximately 1mA/cm{sup 2} or higher). This phenomenon is considered to result from accumulation of nitrogen preferentially in the surface area to prevent dissolution of steel. Nitrogen dissolved in the austenic phase improves resistance of the steel to pitting corrosion. This phenomenon is considered to result from controlled decrease in pH level during the initial stage of pitting corrosion, ...

Energy Technology Data Exchange (ETDEWEB)

The microstructure of the layers produced by plasma nitriding austenitic stainless steel at different treatment temperatures (400 and 500 C) were studied by transmission electron microscopy (TEM) together with X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results show that the microstructures were composed of 'expanded austenite' ({gamma}{sub N}) and {alpha}(ferrite)+CrN following plasma nitriding at lower and higher treatment temperatures, respectively. The former contains stacking faults and deformed twin substructures, while the latter is made up of colonies displaying a lamellar structure. Kurdjumov-Sachs or Nishiyama-Wassermann orientation relationships between the {alpha} and CrN layer were observed. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The effect of accelerated thermal cycling on a joint between modified 9Cr-1Mo steel (Grade 91) and Alloy 800 welded with Inconel 82 and 182 filler material is discussed. This is part of a trimetallic transition joint involving Grade 91-Alloy 800-316LN austenitic stainless steel for steam generator application. It has been shown that, during thermal cycling following the typical post-weld tempering treatment at 760 deg. C for 2 h, no carbon diffusion occurs from the ferritic steel towards the weld metal. There is, in fact, a hardness increase at the ferritic steel/weld metal interface which is probably a result of work hardening. Carbon migration sets in only after unusually long post-weld heat treatments for 20 and 50 h at 760 deg. C followed by thermal cycling. Significantly, even under the most severe thermal cycling test conditions imposed, no cracking or oxide notching could be detected, thus demonstrating the superior ...

Energy Technology Data Exchange (ETDEWEB)

This paper reports that the co-deposition of chromium and silicon into a 2.25Cr-1.0Mo-0.15C steel, alloy 800, and type 304 stainless steel has been achieved using the pack cementation process. The ferritic coating produced on the 2.25 Cr-1.0Mo steel was approximately 225 {mu}m (9 mils) thick, whereas the inward diffusion of chromium and silicon produced a two-phase structure of ferrite and austenite for type 304. Chromium and silicon were incorporated into the austenitic solid solution upon diffusion into alloy 800. All coatings had approximately 25 to 35 wt% Cr and 2 to 3% Si at the surface. Cyclic oxidation testing in air of the coated 2.25Cr-1.0Mo steel (T = 700{degrees} C) and type 304 (T = 1035{degrees} C) showed a dramatic decrease in the oxidation kinetics compared to the original uncoated alloys. The cyclic oxidation of alloy 800 was also improved.

Energy Technology Data Exchange (ETDEWEB)

The pitting resistance of Fe-Cr and Fe-Cr-Mo alloys has been correlated with characteristics of the passive films analyzed by Auger electron spectroscopy (AES). Increased film protectiveness as a result of increased Cr in the alloy can be directly attributed to Cr enrichment of the film and decreased film thickness. Increased Mo in the alloy or passivation at noble potentials promotes passive film resistance to breakdown, but neither does much to change the macrocharacteristics of the film. Rather, it is suggested that the roles of alloying and/or passivation conditions are related to the susceptibility and distribution of weak points of the film. In solutions in which pitting occurs, chloride is generally not incorporated into the film, suggesting that the role of halides is to interact with weak points of the film at the solution/film interface. At 260/sup 0/C, the films are much thicker and likely to be much more defective in structure than those formed at 80/sup 0/C.

International Nuclear Information System (INIS)

The critical part of the trimetallic transition joint (type 304 stainless steel/Alloy 800/2.25 Cr-1 Mo steel), the Alloy 800/2.25 Cr-1 Mo steel joint welded with Inconel 182, was subjected to thermal cycling between room temperature and 873 K. The thermal cycling test procedure used produces accelerated failures in transition joints similar to those observed in steam generators of operating power plants. On thermal cycling, precipitation at the weld/ferritic steel interface decreased on post-weld heat treatment. This precipitation increased with increased prior ageing and applied stress. The results of these tests indicated a considerable improvement in performance of the trimetallic transition joint compared to the direct (bimetallic) transition joint. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Microstructural analyses by several advanced metallographic techniques were conducted on austenitic stainless steel mockup and core shroud welds that had cracked in boiling water reactors. Contrary to previous beliefs, heat-affected zones of the cracked Type 304L, as well as 304 SS core shroud welds and mockup shielded-metal-arc welds, were free of grain-boundary carbides, which shows that core shroud failure cannot be explained by classical intergranular stress corrosion cracking. Neither martensite nor delta-ferrite films were present on the grain boundaries. However, as a result of exposure to welding fumes, the heat-affected zones of the core shroud welds were significantly contaminated by oxygen and fluorine, which migrate to grain boundaries. Significant oxygen contamination seems to promote fluorine contamination and suppress thermal sensitization. Results of slow-strain-rate tensile tests also indicate that fluorine exacerbates the ...

Energy Technology Data Exchange (ETDEWEB)

In the present paper, the chemical composition of passive films formed on both phases of two types of duplex stainless steels (UNS S31803 and UNS S32304) is determined at the micro-scale using Auger electron spectroscopy (AES). Samples were either mechanically polished (down to diamond pastes) or electrochemically etched in acidic solutions. The micro-electrochemical behavior of samples was then determined in sodium chloride media by means of the electrochemical micro-cell technique (capillary diameters of 30 {mu}m). The results obtained were analyzed considering the passive film chemical composition. Quantitative relationships between electrochemical parameters and the distribution of chromium and iron in the oxide layer were found. Due to differences in mechanical properties between ferrite and austenite, a heterogeneous stress distribution is generated in both phases. A method based on thermal-mechanical simulation was used to quantify ...

Energy Technology Data Exchange (ETDEWEB)

Nitridation of Cr-bearing alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant CrN or Cr{sub 2}N base surfaces of interest for a range of electrochemical devices, including fuel cells, batteries, and sensors. This paper presents results of exploratory studies of the nitridation of commercially available, high Cr (30-35 wt%) Ni-Cr alloys and a ferritic high Cr (29 wt%) stainless steel for proton exchange membrane fuel cell (PEMFC) bipolar plates. A high degree of corrosion resistance in sulfuric acid solutions designed to simulate bipolar plate conditions and low ICR values were achieved. Oxygen impurities in the nitriding environment were observed to play a significant role in the nitrided surface structures that formed, with detrimental effects for the Ni-Cr base alloys, but beneficial effects for the stainless steel alloy. Positive results from single-cell fuel cell ...

Energy Technology Data Exchange (ETDEWEB)

Fretting wear test in room temperature water was performed to evaluate the wear coefficient of CANDU (CANadian Deuterium Uranium) steam generator (SG) tube material (Alloy 800) against 410 type martensitic stainless steels. The main focus is to compare the wear behaviors between Alloy 800 and Inconel 690. Test conditions are 10{approx}30N of normal load, 200{approx}450mm of sliding amplitude and 30Hz of frequency. The result indicated that the wear rate of Alloy 800 was higher than those of Inconel 690 at various test condition such as normal loads, sliding amplitudes etc. From the results of SEM observation, there was little evidence of plastic deformation layer that were dominantly formed on the worn surfaces of Inconel 690. Also, wear particles in Alloy 800 were released from contacting asperities deformed by severe plastic flow during fretting wear. Main cause of wear rate between Alloy 800 and Inconel 690 may be due to the difference of hardness between ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties of Fe-Mn-Al alloys; passive films formed on nonmagnetic Cr-Mn-N stainless steels in ...

Energy Technology Data Exchange (ETDEWEB)

Structure of ferrite in drawn pearlitic steel containing 0.9 mass% C was investigated with X-ray diffraction technique using synchrotron radiation. In the detailed analysis of diffraction peaks of ferrite during the drawing process, it was experimentally revealed that the transformation of ferrite from bcc to bct due to the supersaturation of carbon in ferrite of heavily drawn pearlitic steel.

International Nuclear Information System (INIS)

Results of an investigation of the weldability of compact hollow automobile parts are reported. The use of magnetically impelled arc butt (MIAB) welding for a piston rod (OD_22_mm x 2.2_mm thickness), a shock-absorber (OD 40 mm x 2.2 mm) and a torque rod (OD 34 mm x 6 mm) has been investigated. Metallographic examination and comprehensive mechanical testing has been conducted to demonstrate the effectiveness of the method for joining of these types of automobile components

Energy Technology Data Exchange (ETDEWEB)

This report summarizes work performed by Argonne National Laboratory on fatigue and environmentally assisted cracking (EAC) in light water reactors from January 1997 to June 1997. Topics that have been investigated include (a) fatigue of carbon, low-alloy, and austenitic stainless steels (SSs) used in reactor piping and pressure vessels, (b) irradiation-assisted stress corrosion cracking of Types 304 and 304L SS, and (c) EAC of Alloys 600 and 690. Fatigue tests were conducted on ferritic and austenitic SSs in water that contained various concentrations of dissolved oxygen (DO) to determine whether a slow strain rate applied during various portions of a tensile-loading cycle is equally effective in decreasing fatigue life. Slow-strain-rate-tensile tests were conducted in simulated boiling water reactor (BWR) water at 288 C on SS specimens irradiated to a low fluence in the Halden reactor and the results were compared with similar data from a ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Nanodimensional powders of cubic copper ferrite are synthesized by two-steps procedure of co-precipitation of copper and iron hydroxide carbonates, followed by mechanochemical treatment. X-ray powder diffraction, Moessbauer spectroscopy and temperature-programmed reduction are used for the characterization of the obtained materials. Their catalytic behavior is tested in methanol decomposition to hydrogen and CO and total oxidation of toluene. Formation of nanosized ferrite material is registered even after one hour of milling time. It is established that the prolonging of treatment procedure decreases the dispersion of the obtained product with the appearance of Fe2O3. It is demonstrated that the catalytic behavior of the samples depends not only on their initial phase composition, but on the concomitant ferrite phase transformations by the influence of the reaction medium. -- Graphical abstract: It is demonstrated that the ...

British Library Electronic Table of Contents (United Kingdom)

An ultrafine-grained ferrite/cementite (UGF/C) steel with a local high density of cementite particles was fabricated through caliber-warm-rolling followed by annealing and resulted in a bimodal-sized microstructure. The characteristic bimodal-sized microstructure was attributed to the original ferrite-pearlite structure and cementite spacing, and reflected the original ferrite-pearlite structure. The smaller-sized clusters corresponded to the former pearlite regions and the larger-sized clusters to the proeutectoid ferrite regions. The cementite particles naturally localized within the former pearlite region. Most of the ferrite coarsening did not occur until the cementite particle spacing reached a critical value. The UGF/C microstructure with a bimodal grain size showed a yield strength ...

UK PubMed Central (United Kingdom)

IntroductionMale sexual dysfunction is a common complication of diabetes (DM), but the relative impact of erectile dysfunction (ED), orgasmic dysfunction (OD), and/or...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Magnetic field, thickness and magnetic forming effect on general mode and quantitative parameters of the domain structure (DS) of ferrite-garnet (EuEr)/sub 3/(FeGa)/sub 5/O/sub 12/ monocrystalline plates (111) is investigated. Field interval of circle (cone) and ring domain stability is determined. It is shown that DS of ferrite-garnet crystals with uniaxial an6sotropy has some peculiarities, that can be explained by cubic anisotropy effect.

Energy Technology Data Exchange (ETDEWEB)

Mixed microstructures have been studied in low- carbon microalloyed steels suitable for automotive applications, after continuous cooling from the hot-rolled condition. Microstructural features such as polygonal ferrite, bainitic and acicular ferrite and microphase constituent are identified using transmission electron microscopy. The influence of these mixed structures on the tensile strength, impact toughness and fracture behaviour is examined. It is found that improvements in impact toughness as compared with microalloyed medium- carbon ferrite/pearlite steels can be achieved from these predominantly acicular structures developed by controlling alloy composition and continuous cooling of these lower carbon steels. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Production costs for commercial-sized Populus plantations were developed from a series of research programs sponsored by the US Department of Energy's Short Rotation Woody Crops Program. Populus hybrid planted on good quality agricultural sites at a density of 2100 cuttings ha{sup {minus}1} was projected to yield an average of 16 Mg (OD) ha{sup {minus}1}yr{sup {minus}1}. Discounted cash flow analysis of multiple rotations showed pre-harvest production costs of $17 (US) Mg{sup {minus}1}(OD). 19 refs., 1 fig., 3 tabs.

British Library Electronic Table of Contents (United Kingdom)

This paper presents results from a research case study that examined the distribution of travel time of origin-destination (OD) pairs on a transportation network under incident conditions. Using a transportation simulation dynamic traffic assignment (DTA) model, incident on a transportation network is executed under normal conditions, incident conditions without traveler information availability, and incident conditions assuming that users had perfect knowledge of the incident conditions and could select paths to avoid the incident location. The results suggest that incidents have a different impact on different OD pairs. The results confirm that an effective traveler information system has the potential to ease the impacts of incident conditions network wide. Yet it is also important to n...

Energy Technology Data Exchange (ETDEWEB)

Four low activation alloy classes, two austenitic and two ferritic, have been incorporated into the MOTA-1B experiment in the FFTF reactor to provide an early assessment of the suitability of such alloys for reactor service.

CERN Document Server

Differences in synchrotron radiation induced gas desorption from stainless steel and aluminium alloy

British Library Electronic Table of Contents (United Kingdom)

This paper reports the results of in situ observation of fatigue crack growth in a ferrite?pearlite steel. Stress intensity factor range (?K) decreasing/increasing and constant-?K fatigue tests have been carried out. In banded pearlite orientation, intense crack branching was observed which leads to fatigue crack retardation. Crack closure during the test was monitored to understand the fatigue crack growth behaviour.

Energy Technology Data Exchange (ETDEWEB)

Effect of ultrasonic-wave irradiation on the Mn-Zn ferrite powder suspension prepared by solid-state reaction and alcoholic dehydration methods was investigated. Size, distribution, and morphology of the powders prepared at different temperatures were examined, as a function of irradiation time. It was observed that the powders were reduced in size by ultrasonic energy through distinct routes. 8 refs., 7 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

Early failure of an induction-hardening carbon steel pipe, which was used to transport tailing slurry, was caused by pitting corrosion. The microstructure on the internal pipe surface layer was found being a mixture of martensite, pearlite and ferrite. In this work, the pitting corrosion behavior of each constitute in the microstructure of steel is investigated with electrochemical noise analyses; the electronic properties of passive films were studied with Mott-Schottky relationship. It is found that the passive films formed on the materials under investigation are highly disordered n-type semiconductors. The high-to-low pitting susceptibility is ferrite > martensite > pearlite. The pitting resistance is related to the semiconductive nature of the passive film formed on each constitute. The pitting susceptibility increases with the donor concentration in the passive films. (author)

British Library Electronic Table of Contents (United Kingdom)

Fatigue crack growth tests of three ferrite-pearlite steels with different size and spacing of pearlite particles, which were uniformly distributed in the ferrite matrix, were carried out to investigate the effect of microstructure on fatigue crack growth behavior in the Paris regime. The fatigue crack growth rates for the three materials did not coincide with each other, even when the crack growth curves were arranged by the effective stress intensity factor range. From in situ observations, crack tip stress shielding phenomena, such as interlocking and branching, were found on the crack wake, which enhanced fatigue crack growth resistance. A small size and spacing of pearlite particle seemed to induce small but frequent crack deflections, which resulted in crack closure phenomena. On the...

International Nuclear Information System (INIS)

In this study, effects of alloying elements such as Mo, Cr and Ni on intergranular corrosion (IGC) resistance of Mo contained austenitic stainless steels in boiling 65% nitric acid solution (Huey Test) were studied. Obtained results are as follows; (1) Mo deteriorates IGC resistance of austenitic stainless steel in Huey test due to enhance precipitation of Laves ((Fe, Cr)_2Mo) phase at grain boundary. (2) Cr improves IGC resistance of Mo contained austenitic stainless steel in Huey test, which is considered to reduce dissolution rate of Laves phase into nitric acid solution by increasing Cr content in Laves phase as increasing Cr content of stainless steel. (3) Ni suppresses occurrence of IGC of Mo contained austenitic stainless steel in Huey test. (author).

Energy Technology Data Exchange (ETDEWEB)

PWR steam generators have suffered from a variety of degradation phenomena. This paper identifies the corrosion-related defects and their probable causes and suggests approaches to correct and prevent corrosive activity. In the attempt to solve the degradation problems, research programs have concentrated on modifying materials, stresses, and the chemical environment in both new and operating steam generators. The following corrosion-related defects have been studied: tube wastage, denting, primary side (ID) intergranular stress corrosion cracking (IGSCC), OD-initiated intergranular attack (IGA), pitting, and corrosion fatigue. Plants affected by wastage have greatly reduced their problem by adopting an all volatile treatment (AVT). In the case of denting, a less aggressive chemical environment is recommended. Primary side IGSCC responds to temperature reduction, stress relief, and material improvements, while flushing and boric acid addition minimizes ...

Energy Technology Data Exchange (ETDEWEB)

A key factor that demands special attention in the pipeline construction is the cold bending process, since 30 to 40% of the pipes use this process in the field. This study aimed to evaluate the X80 cold bending operational parameters, in order make viable the use of this process in the installation of future onshore pipelines. Three 34''OD x 0,750'' pipes were bended. The bending was conducted using a hydraulic equipment with application of equally spaced punches, recording the correspondent angles related to the elastic and plastic deformations in order to assess the spring-back effect and performing dimensional inspection. Samples from pipe and the weld were subjected to mechanical and metallographic tests. It was possible to obtain a 19 deg curve and 27D radius without presenting any evidence of wrinkles, out of roundness or any type of mechanical damage. After analysis, all criteria established from project specifications ...

Energy Technology Data Exchange (ETDEWEB)

The shot peening of the outer surface of Alloy 800 is proposed by the steam generator supplier in order to increase the stress corrosion cracking resistance of the tubes. The benefits and drawbacks of such a treatment are evaluated, focusing on the main concern i.e. a possible enhanced tendency of stress corrosion cracking at the transition of the expanded tube-to-tubesheet joint. Stress corrosion tests as well as residual stresses measurements demonstrate no significant difference between peened and unpeened tubes at that location. The other concerns such as stability of the compressive stresses, increased risk of pitting or intergranular attack and pollution of the secondary circuit by fragmented beads appear the as minor concerns.

International Nuclear Information System (INIS)

The fabrication of the ZT-40 torus, a large complex all-ceramic toroidal plasma containment vessel, is described. Several glass sealants covering the temperature range of 500 to 1300"0C, were developed and used to ''braze'' segments of the torus together, sapphire windows to the torus and the required pump-out and diagnostic parts to the ceramic vacuum vessel. Designs of window seals were developed that allowed sealing of the sapphire windows in a vertical position with minimum sealing glass flow.

Energy Technology Data Exchange (ETDEWEB)

Long crack fatigue threshold ({delta} K{sub th}) and crack closure behaviour of two thermomechanically processed microalloyed (MA) ferrite-pearlite steels are reported. {delta} K{sub th} and crack closure were measured using a dynamic compliance measurement technique. Crack closure was observed at low load ratios (R < 0.5) and the fatigue thresholds decreased with increasing load ratio. In both steels, the closure-free intrinsic threshold ({delta} K{sub eff} {sub th}) was found to be independent of the load ratio. (orig.)

Energy Technology Data Exchange (ETDEWEB)

It is known that in size reduction of the granular structure of ferrite and ferrite-pearlite steels the temperature of the transformation from ductile to brittle condition is lowered. This effect can also be caused by an increase in the dispersity of intragrain and intergrain segregations (sulfides, carbonitrides, and segregations of impurity atoms), which accompanies grain size reduction and promotes initiation and propagation of cracks. In order to clarify the mechanism of fracture of steel in the region of the ductile-brittle transition steel 45 with different grain sizes and pearlite morphologies has been investigated.

Energy Technology Data Exchange (ETDEWEB)

Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X = 1 {mu}m and an intermediate inter-pillar gap size of Y = 4 {mu}m with superhydrophobic CAs over 170 . Surface analysis with X-ray photoelectron spectroscopy (XPS) revealed ...

International Nuclear Information System (INIS)

Full text: It was recently-established for hexagonal barium ferrite-industrially important magnetically hard material that refinement of the crystallite dimensions into the nanoscale regime, typically #<=# 10 nm, leads after heat treatment at temperatures 800-1000 deg C to significant coercivity increase of up to 6.5 kOe (#approx#3-4 times) with saturation magnetisation values of 50-55 emu/g (#approx#95% of bulk at room temperature). High-energy mechanochemical processing has been applied to prepare nanostructural (nanocrystalline-amorphous) composites. High resolution electron microscopy studies reveal that the enhancement of the final magnetic properties was due to formation of magnetically noninteracting #approx#l,#mu#m Ba-ferrite particles with 5-10 nm amorphous surface layer - depending on annealing parameters. Similar situation was established also for ball milled strontium ferrite (SrFe_1_2O_1_9) powders where ...

Energy Technology Data Exchange (ETDEWEB)

In recent years, the phase stability of austenitic stainless steels, and its effect on the mechanical properties of stainless steels, have been the subject of much interest. With the availability of new experimental techniques, new theoretical methods, and new computational procedures, significant advances have been made in understanding, and being able to predict, phase stability and mechanical properties of stainless steel welds. This paper reviews some of these developments, with an emphasis on recent work that has been done at Oak Ridge National Laboratory.

International Nuclear Information System (INIS)

... Industry, Material Science Research Laboratory, Yokosuka, Kanagawa (Japan)

International Nuclear Information System (INIS)

Duplex stainless steels are widely used in severe corrosion environments because of their good corrosion performance. This paper deals with the influence of aging treatments on the intergranular corrosion (IGC) resistance of a commercial duplex stainless steel, SAF 2205. Duplex stainless steel was given aging treatments in the range 773-1173 K for time periods ranging from 6 min to 100 h. Optical microscopy and XRD was carried out on the aged stainless steels for the microstructural study. The aged samples were evaluated for the IGC susceptibility with the ASTM standard practices. Potentiodynamic cyclic polarization studies were also carried out to investigate the influence of aging treatments on the passivity breakdown. The results indicate that the sigma phase gets precipitated and is responsible for grain boundary attack. (author).

Energy Technology Data Exchange (ETDEWEB)

Chromium nitride/Cr coating has been deposited on surface of 316L stainless steel to improve conductivity and corrosion resistance by physical vapor deposition (PVD) technology. Electrochemical behaviors of the chromium nitride/Cr coated 316L stainless steel are investigated in 0.05 M H{sub 2}SO{sub 4}+2 ppm F{sup -} simulating proton exchange membrane fuel cell (PEMFC) environments, and interfacial contact resistance (ICR) are measured before and after potentiostatic polarization at anodic and cathodic operation potentials for PEMFC. The chromium nitride/Cr coated 316L stainless steel exhibits improved corrosion resistance and better stability of passive film either in the simulated anodic or cathodic environment. In comparison to 316L stainless steel with air-formed oxide film, the ICR between the chromium nitride/Cr coated 316L stainless steel and carbon paper is about 30 ...

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately estimates the tensile behavior of the ...

Energy Technology Data Exchange (ETDEWEB)

The global production of steel is predicted to increase rapidly to meet future demands. In order to conserve the natural resources, certain measures must be taken. These include perfecting the recycling of steel, improving the performance to extend the life of the material, and reduce the need for massive production of steel by increasing the strength of the material. This paper presented a design concept for ultrafine complex microstructure steel. The National Research Institute for Metals in Japan has worked on a project which investigated 800 MPa ferrite steel for welded structures with a chemical composition similar to 400 MPa-class plain carbon steel. The doubled strength was attributed to grain refinement. Novel welding techniques were also used for joining the ultrafine microstructure. In this study, low carbon Si-Mn ferrite-pearlite steels were subjected to a thermo-mechanical treatment to produce a microstructure of 1 micron order ...

Energy Technology Data Exchange (ETDEWEB)

The synergistic effects of displacement damage and atomic hydrogen and helium on swelling of the ferritic/martensitic steel, F82H, has been investigated. The irradiation was performed at temperatures between 470 and 600 deg. C to 50 dpa (displacement per atoms) under conditions of simultaneous ion beams consisting of Fe{sup 3+}, He{sup +} and H{sup +} ions or Fe{sup 3+} and He{sup +} ions. The swelling of F82H steel under triple beams with 18 appm He/dpa and 70 appm H/dpa was larger than that under dual beams with 18 appm He/dpa. The swelling in F82H under triple beams increased with decreasing irradiation temperature from 0.1% to 3.2%, while swelling under dual beams was between 0.04% and 0.08%. On the other hand, in the case of triple beam irradiation with a high ratio of gas/dpa, the swelling tended to increase with irradiation temperature. The swelling in ferritic/martensitic steels is significantly enhanced by the synergistic effect of ...

International Nuclear Information System (INIS)

M-type hexagonal ferrite composition, Ba(1-x)SrxFe12O19 (x=0.0, 0.2, 0.4, 0.6, 0.8 and 1.0), was prepared by a two route ceramic method. Complex permittivity (?'-j?'') and complex permeability (?'-j?'') have been measured using a network analyzer from 8.2 to 12.4 GHz X-ray diffraction confirmed the M-type hexagonal structure and a scanned electron micrograph was used to analyze the grain size distribution of ferrite. Substitution of Sr2+ ions causes an increase in porosity that deteriorates the electromagnetic and microstructural properties in the doped samples. Both dielectric constant and dielectric loss are enhanced in comparison to the permeability and magnetic loss over the entire frequency region. This is due to a resistivity variation and the formation of Fe2+ ions, which increases the hopping mechanism between Fe2+ and Fe3+ ions.

International Nuclear Information System (INIS)

The Environmental Management System (EMS) is an instrument to manage the interaction between the organization and the environment. The scope od EMS is to reduce the environmental impact and to achieve improvements in overall performances. In particular, the focus point of EMS implementation is the method for identifying and assessing significant environmental aspects. The results of the literature and regulation reviews (Perotto 2006) have shown that rigourous repeatable and transparent methodologies do not exist. This paper presents a proposal method for identifying and assessing significant environmental aspects, that has all three of these important characteristics. In particular, the proposal methodology for assessing aspects is based on some criteria that are combined in a specific algorithm. It is important to specify that to make a correct application of the method a preliminary rigorous approach to investigating the environment and the activities of ...

International Nuclear Information System (INIS)

A series of nine model ferritic alloys were ion irradiated at #propor to#300 C using 2.5 MeV He ions to a dose of 1.4 x 10"2"1 ion/m"2, which corresponds to #propor to#0.1 dpa at a depth of 2 #mu#m and #propor to#3.5 dpa at the peak damage region which occurs at about 4 #mu#m deep. The resultant changes in hardness as a function of depth were measured using a Nanoindenter "t"r"a"d"e"m"a"r"k. TEM was used to investigate the defect distributions. The effect of various solutes, Cu and N in particular, but Mn and Ti as well, on the change of hardness and the defect distribution due to the ion irradiation are discussed. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is to evaluate the synergistic effect of helium and hydrogen on Fe-Cr ferritic model alloys, to provide basic understanding concerning development of fusion reactor components. Single, dual and triple ion-beams consisting of Fe{sup 3+}, He{sup +} and H{sup +} were used for irradiation, at temperatures 470-600 deg. C and dose to 50 dpa at 1 {mu}m. The dual beam irradiation with He enhanced cavity nucleation extensively to swelling of about 0.4%, whereas the dual beam irradiation with H did not significantly affect the microstructure. In the case of triple ion irradiation, the synergistic effect of He and H was confirmed clearly; relative large void formation and enhanced swelling to almost 5%. The synergistic effect suggests that the role of H is important for void growth and dislocation bias.

British Library Electronic Table of Contents (United Kingdom)

Nanocrystalline MnFe"2O"4 ferrite was prepared by using autocombustion technique (flash). The microstructure and magnetic properties are studied. The results of XRD and TEM clarified that, this ferrite is nanosized with particle size (39 nm). Magnetic measurements showed a ferromagnetic behavior with T"C = 613 K, the saturation magnetization M"s = 13.71 emu/g, remanent magnetization M"r = 0.1694 emu/g and, coercivity H"c = 25.6 Oe. Natural material, egg white used as an aqueous medium to extend prepare nanoparticles better than other chemical interesting materials.

International Nuclear Information System (INIS)

Ferrite of system, namely Ni_1_-_xZn_xFe_2O_4 with x = (0.0, 0.2, 0.4, 0.6, 0.8, 1.0), have been prepared by solid state reaction to investigate the effect of gamma rays irradiations using Co"6"0 source on the cation distribution, structural and magnetic properties. The unirradiated and irradiated samples were then subjected to characterization techniques such as X-ray diffraction, magnetization and AC susceptibility. The results of these characterizations are found to be different for irradiated from that of the pristine sample. The modifications in respect of irradiated samples are explained in terms of the ion-induced disorder. The important result of #gamma#-irradiation on the cation distribution, structural and magnetic properties is the change of ratio Fe"2"+/Fe"3"+. Possible reasons on the results are proposed.

Energy Technology Data Exchange (ETDEWEB)

For the purpose of solving the limitations such as shape and dimension for magnetic compact fabricated by conventional anisotropic forming under magnetic orienting field, the feasibility of a new magnetic forming process was studied. Ferrite powder mixed with UV resin was compacted in the die mold and followed by alignment under the magnetic field. Effects of viscosity of UV resin and forming condition on magnetic characteristics of the compact was investigated. Maximum degree of alignment for the ferrite powder reached to 0.826. It was predicted that the proposed method had make it possible to fabricate a high performance magnet having the anisotropic alignment of the magnetic powder. The UV resin is desirable to have low viscosity, good properties such as formability and configuration stability for the compact and also parting- ability between the metal mold and the compact. (author)

International Nuclear Information System (INIS)

This paper deals with the pitting corrosion of evaporators in the liquid - radwaste system of nuclear power stations. Corrosion testrs were conducted by the anodic polalization of specimen in the chloride solution. (1) The initiation of the pitting in SUS 304, SUS 316 stainless steels was inhibited by addition of NaOH and H_3BO_3, however, these addition had no effect on the pitting propagation. (2) Inconel 625 had the resitivity against the pitting initiation superior to that of stainless steels, but this was not necessarily in the case of the pitting propagation. (3) It is noticed for pitting prevention that the environmental and material effect on the pitting initiation differed from that on the pitting propagation. (author).

Science.gov (United States)

Three bonding agents were evaluated to determine which were most effective in enhancing the bond of resin composite to stainless steel. A light-activated resin composite was bonded to a total of 60 stainless steel specimens using Panavia, Cover-Up, or Silicoating. Tensile bond strength measurements revealed that all three agents provide a satisfactory means of increasing adherence of the esthetic veneer without decreasing bonding through thermocycling of the specimens. Panavia and Cover-Up were significantly more effective than Silicoating and appear to be easier to use. PMID:8297460

International Nuclear Information System (INIS)

The effects of modification with Ti and Nb, heat treatment and solute segregation on void suppression in 316 stainless steel were studied using HVEM in the temperature range of 623-873 K after solution treatment at 1323-1473 K. Post-irradiation compositional analysis was performed by an energy dispersive X-ray analyzer. In Ti-modified stainless steel, void swelling peaks appeared at 723 K and 823 K. On the other hand, when the stainless steels modified by both Ti and Nb were irradiated, the void swelling was effectively suppressed, particularly the growth rate of a void was remarkedly retarded. This void suppression effect was easily recognized with increasing Nb concentration. Compositions such as Mo, Cr, Ti and Ni changed during irradiation and Ni, Si and Ti enriched around voids, whereas Cr and Mo depleted. (orig.).

International Nuclear Information System (INIS)

... Industry, Material Science Research Laboratory, Yokosuka, Kanagawa (Japan)

Science.gov (United States)

In this paper a new procedure, addressed as Interpolation Damage Detecting Method (IDDM), is investigated as a possible mean for early detection and location of light damage in a structure struck by an earthquake. Damage is defined in terms of the accuracy of a spline function in interpolating the operational mode shapes (ODS) of the structure. At a certain location a decrease (statistically meaningful) of accuracy, with respect to a reference configuration, points out a localized variation of the operational shapes thus revealing the existence of damage. In this paper, the proposed method is applied to a numerical model of a multistory frame, simulating a damaged condition through a reduction of the story stiffness. Several damage scenarios have been considered and the results indicate the effectiveness of the method to assess and localize damage for the case of concentrated damage and for low to medium levels of noise in the recorded signals. The main advantage ...

International Nuclear Information System (INIS)

Pitting corrosion is a kind of electrolytic corrosion by which the surface of a material is locally affected owing to inhomogeneities on the part of the material or medium. The paper deals briefly with questions relating to the importance, to parameters medium or materialwise, influence on production and construction, as well as the general conditions for pitting corrosion. In particular oxygen corrosion in unalloyed and low-alloy steel, and pitting corrosion in ferritic chromium-steel and austenitic chromium-nickel (molybdenum) steel is described. (DG).

International Nuclear Information System (INIS)

The structural changes attendant on intermartensitic transformation in a Ni-Mg-Ga shape memory alloy are considered using magneto-optical visualization with the help of ferrite-garnet monocrystalline films. It is established that on the intermartensitic transformation the complete reorganization of martensite macrostructure fails. Martensite crystals resulted from the basic transformation change somewhat their sizes on intermartensitic transition. The existence of large-scale labyrinth magnetic domain structure is revealed

International Nuclear Information System (INIS)

General corrosion behavior of ALLOY 800 in high temperature water was studied in relation to its surface film structure. The surface film formed in water was found to decrease the corrosion rate of ALLOY 800. This film is composed of Ni ferrite, and can be obtained by oxidation in air or steam. Based on these results, air or steam oxidation treatment to inhibit Ni and Co release of ALLOY 800 into high temperature water is proposed. (author).

Energy Technology Data Exchange (ETDEWEB)

Azobenzene dyes are effective inhibitors for austenitic 304 L and 316 L stainless steel corrosion in high acidic medium up to 7N. A good efficiency is obtained from weight loss and electrochemical Rsub(p) measurements in hydrochloric acid, while no inhibition is observed in sulfuric solutions. Transformation from the primarily azobenzene to other compounds give rise to enhanced protection of steel samples, and probable structures of the inhibiting species are proposed in view of our results.

International Nuclear Information System (INIS)

Paper estimates the corrosion resistance and studies the character of dissolving of silicon-bearing austenite stainless steels in strongly oxidizing media containing phosphate and fluoride admixtures. Corrosion behaviour of the studied steels is determined to depend essentially on the content of admixture or alloying silicon, as well as, on their phase composition in many respects determined by the thermal treatment condition. Refs. 22, figs. 1, tabs. 2.

International Nuclear Information System (INIS)

Mutual influence of phosphorus and carbon on the tendency to integranular corrosion (IGC) of tempered austenitic stainless steels in boiling solutions of 65% HNO_3 and 27% of HNO_3+40 g/l Cr"6"+ was investigated. It is ascertained that under the action of carbon additions susceptibility of phosphorus-containing steels to IGC increases considerably in pure nitric acid and decreases in nitric acid containing the oxidant. Possible reasons for the effects observed are discussed.

International Nuclear Information System (INIS)

The study by impedance and photoelectrochemical measurements of passive films formed on an AISI 304 type stainless steel shows that important parameters of the electronic structure of these films are modified under #alpha# irradiation, namely: width of the space charge region, donors concentration and diffusion length for minority carriers. The consequences of #alpha# irradiation on localized corrosion processes are discussed.

International Nuclear Information System (INIS)

By means of ESCA the composition and the thickness of passive films formed on austenitic stainless steels were investigated after the attack of nitric acid at various temperatures and acid concentrations. The outermost layers of the oxide film consist of SiO_2, then a layer rich of Cr-oxid follows, containing also some Mo in the four- and sixvalent state. Ni does not contribute to the oxide film. Cr is also enriched in the metal just below the oxide film. (orig.).

Energy Technology Data Exchange (ETDEWEB)

By using a plasma nitriding procedure at the PUPR Mirror Cusp Plasma machine, surface hardness is increased in 302/304-type stainless steel samples by exposing them to high-ion-density plasma at high vacuum. This method successfully dopes the surface of the material with strengthening nitrogen ions, without the use of chemical procedures that sacrifice the resistance to corrosion of the given material. A 500 V negative bias is placed on the sample exposed to the nitrogen plasma, where high-energy ions are therefore attracted and immersed into the metallic matrix microns into the surface of the stainless steel. This potential maintains a constant surface temperature at approximately 800 deg. C. The plasma parameters including ion density and plasma temperature were diagnosed using single Langmuir probes. The stainless steel samples were then tested using scanning electron microscopy (SEM), and Vickers micro-hardness testing ...

International Nuclear Information System (INIS)

The design of the ITER primary first wall incorporates a multi-layered structure consisting of a layer of beryllium bonded to a layer of copper alloy with embedded stainless steel tubes which in turn is bonded to a stainless steel structure. In this configuration, the stainless steel provides structural support, the copper alloy improved resistance to high heat loads, and the beryllium layer a low Z metal interface with plasma. Fabrication, testing and control of this multi-layered structure, and indeed the entire blanket shield module, calls for advanced methods. Several associations in the four home teams and their industrial partners have been involved in various fabrication and joining tasks now grouped under L4 blanket project. In this paper, an overview of the work done so far for joining stainless steel to stainless steel, stainless steel to copper alloy, ...

Energy Technology Data Exchange (ETDEWEB)

A study has been made of the passive film remaining over pits on stainless steel using a high resolution transmission electron microscope. Type 305 stainless steel was passivated in a borate buffer solution and pitted in ferric chloride. Passive films formed at 0.2 V relative to a saturated calomel electrode were found to be amorphous. Films formed at higher potentials showed only broad diffraction rings. The passive film was found to cover a remnant lacy structure formed over pits passivated at 0.8 V. The metallic strands of the lace were roughly hemitubular in shape with the curved surface facing the center of the pit.

British Library Electronic Table of Contents (United Kingdom)

Gas nitridation has shown excellent promise to form dense, electrically conductive and corrosion-resistant Cr-nitride surface layers on Ni-Cr base alloys for use as proton exchange membrane fuel cell (PEMFC) bipolar plates. Due to the high cost of nickel, Fe-base bipolar plate alloys are needed to meet the cost targets for many PEMFC applications. Unfortunately, nitridation of Fe-base stainless steel alloys typically leads to internal Cr-nitride precipitation rather than the desired protective surface nitride layer formation, due to the high permeability of nitrogen in these alloys. This paper reports the finding that it is possible to form a continuous, protective Cr-nitride (CrN and Cr2N) surface layer through nitridation of Fe-base stainless steel alloys. The key to form a protective Cr...

Energy Technology Data Exchange (ETDEWEB)

Photocurrent and capacitance measurements of semiconductor passive films formed on metals and alloys can be used to study the electronic properties and reveal indirect information about structure and composition. The current work used these techniques to investigate the electronic properties of the passive films formed on three austenitic stainless steels, types 304L, 316L and 254SMO, in borate. Evidence was found for the existence of a large number of localised mid bandgap states, consistent with amorphous oxides. However, the flat-band potentials of the austenitic stainless steel passive films were found to be independent of both composition and measuring frequency. The most credible explanation for the bandgap values determined from photocurrent measurements is that the passive films are formed as dual layers, iron oxide outer layer and chromium oxide inner layer. This model does not need to evoke the potential dependent bandgaps used by ...

International Nuclear Information System (INIS)

Both the price of nickel and the allergic reaction that it can cause to human beings make it desirable to develop and use nickel-free austenitic stainless steels. The steels should be austenitic so as to avoid ferro-magnetism, a condition which has to be fulfilled for a number of requirements, including its use as implants in the human body, for wrist watch cases and many others. The paper presents the development of a nickel-free steel containing 11 percent manganese, 17 percent chromium, 4 percent molybdenum, and 0.9 percent nitrogen. This austenitic stainless steel has exceptional strength and corrosion resistance. These properties could result in numerous applications of the steel. A limitation, however, is that the steel is not weldable.

Energy Technology Data Exchange (ETDEWEB)

The effect of Mo addition as an alloying element to stainless steel alloys is investigated by capacitance (Mott Schottky approach), and photoelectrochemistry measurements. Complementary studies were made using Auger electron spectroscopy and X-ray photoelectron spectroscopy. The Mott-Schottky approach and the photoelectrochemical studies showed that the presence of Mo as an alloying element affects the semiconductive properties of the oxide films. The analytical results have shown that the oxide films formed on stainless steels are composed by an external Fe rich region and an inner Cr rich region. No significant amount of Mo was found in the outer layers of the film. The presence of Mo leads to an increase of the chromium content in the inner layers of the film, although without increasing the film thickness. (orig.) 30 refs.

Energy Technology Data Exchange (ETDEWEB)

The goal of this project was to increase the high-temperature strength of the H-Series of cast austenitic stainless steels by 50% and the upper use temperature by 86 to 140 degrees fahrenheit (30 to 60 degrees celsius). Meeting this goal is expected to result in energy savings of 35 trillion Btu/year by 2020 and energy cost savings of approximately $230 million/year. The higher-strength H-Series cast stainless steels (HK and HP type) have applications for the production of ethylene in the chemical industry, for radiant burner tubes and transfer rolls for secondary processing of steel in the steel industry, and for many applications in the heat treating industry, including radiant burner tubes. The project was led by Duraloy Technologies, Inc., with research participation by Oak Ridge National Laboratory (ORNL) and industrial participation by a diverse group of companies.

British Library Electronic Table of Contents (United Kingdom)

The colonization of an implant surface by bacteria is an extremely important medical problem, which often leads to the failure of medical devices. Modern surface modification techniques, such as ion implantation, can confer to the surfaces very different properties from those of the bulk underlying material. In this work, austenitic stainless steel 316 LVM has been superficially modified by Si^+ ion implantation. The effect of surface modification on the biocompatibility and bacterial adhesion to 316 LVM stainless steel has been investigated. To this aim, human mesenchymal stem cells (hMSCs), as precursor of osteoblastic cells, and bacterial strains relevant in infections related to orthopedic implants, i.e., Staphylococcus aureus and Staphylococcus epidermidis, have been assayed. For the ...

Energy Technology Data Exchange (ETDEWEB)

Acid Rock Drainage (ARD) is the product formed by the atmospheric oxidation of the relatively common pyrite and pyrrhotite. Waste rock dumps and tailings containing sulfide mineral have been reported at toxic materials producing ARD. Mining in sulphide bearing rock is one of activity which may lead to generation and release of ARD. ARD has had some major detrimental affects on mining areas. The purpose of this study was carried out to develop disposal method for preventing contamination of water and soil environment by waste rocks dump and tailings, which could discharge the acid drainage with high level of metals. Scope of this study was as following: environmental impacts by mine wastes, geochemical characteristics such as metal speciation, acid potential and paste pH of mine wastes, interpretation of occurrence of ARD underneath tailings impoundment, analysis of slope stability of tailings dam etc. The following procedures were used as part of ARD evaluation and prediction to ...

Energy Technology Data Exchange (ETDEWEB)

The use of linear accelerators in radiotherapy is of great importance in Medicine, and according to international recommendations the electron beam dosimetry has to be performed using plane-parallel ionization chambers, previously calibrated in standard gamma radiation fields at accredited laboratories. In this work, calibration methods of plane-parallel ionization chambers used in dosimetry procedures of high energy electron beams of clinical accelerators were presented, tested and intercompared. The experiments were carried out using gamma radiation beams of {sup 60} Co at the Calibration Laboratory of Clinical Dosemeters at IPEN and electron beams od 4 to 16 MeV at the Radiotherapy Department of Hospital Israelita Albert Einstein, Sao Paulo. A method was chosen to be established at IPEN. Proposals of the calibration procedure, calibration certificate and data sheets are presented. (author)

Energy Technology Data Exchange (ETDEWEB)

One of the main factors that require special attention in a pipeline construction is the cold bending process, once depending on the region that the line will be installed the number of bends may achieve 75%, as it was observed in some areas during Campinas-Rio pipeline construction. A study was carried out to evaluate the X80 cold bending operational parameters in order to make viable the use of high strength pipes in the construction of onshore pipelines. For this analysis three pipes of 34 inches x 0.750 inches had been cold bended, the operation was carried out using a hydraulic equipment with punches applications along the pipe, recording the correspondent angles related to the elastic and plastic deformations in order to assess the material spring-back. After the bending process, samples of the weld, extrados and intrados were subjected to mechanical and metallographic tests, as well as performed dimensional inspection of the pipes. It was possible to obtain a 19 deg curve and ...

Energy Technology Data Exchange (ETDEWEB)

The influence of surface oxides of variable composition and nonstoichiometry formed at high temperatures in air on the general corrosion resistance of ferritic chromium steel type 08H17T (Fe-17Cr-1Ti) in weak sulfuric acid has been studied. Anodic passive films formed on steel with different pretreatments have also been examined. The surface oxide of nearly stoichiometric composition formed at 300 C provides for the passive state of steel in sulfuric acid despite its depletion by chromium when compared with that for nonstoichiometric Cr-enriched oxide formed at 600 C. The dissolution and transformation of nonstoichiometric thermal surface oxide in sulfuric acid appear to take place through defect sites, {minus}Fe{sup 2+} ions, and oxygen vacancies of the n-type conductor. The passive film formed on the nonstoichiometric oxide film, which had been produced at 600 C, was found to be more susceptible to open-circuit breakdown compared to the native oxide and to the ...

Energy Technology Data Exchange (ETDEWEB)

Red mud from HINDALCO (Hindustan Aluminium Corporation) Industries Limited, Renukoot, India, contains significant quantities of alumina, iron oxide and silica. Presence of the said constituents makes it a suitable ingredient for the preparation of special cements. Preparation of three varieties of cements was investigated, namely: (a) aluminoferrite (C{sub 4}AF)-belite ({beta}-C{sub 2}S) using lime + red mud + fly ash; (b) aluminoferrite-ferrite (C{sub 2}F)-aluminates (C{sub 3}A and C{sub 12}A{sub 7}) utilizing lime + red mud + bauxite; and (c) sulfoaluminate (C{sub 4}A{sub 3}{bar S})-aluminoferrite-ferrite using lime + red mud + bauxite + gypsum. The effects of composition (proportions of lime, red mud, fly ash, bauxite and gypsum), firing temperature and duration on the properties of cements produced were studied in detail. Cements made from lime + red mud + bauxite or lime + red mud + bauxite + gypsum exhibit strengths comparable or superior ...

International Nuclear Information System (INIS)

Irradiation of ferritic steels with neutrons in the temperture range of room temperature to #propor to# 450deg C results in lattice hardening, which causes an increase in strength and a decrease in ductility. Eight reduced-activation Cr-W-V stels with chromium concentration varying from 2.25 to 12% were irradiated at 365deg C to #propor to# 7 dpa in the Fast Flux Test Facility. A steel with 2.25% Cr and the combination of 2% W and 0.25% V hardened less than those containing vanadium or tungsten alone or a steel with 1% W and 0.25% V. The amount of hardening was similar for Cr-W-V steels with constant vanadium and tungsten concentrations and containing 2.,25, 5, and 9% Cr; a steel with 12% Cr hardened considerably more. Specimens of two conventional Cr-Mo steels, 9Cr-1MoVNb and 12Cr-1MoVW, were also irradiated, and the hardening of these steels was similar to analogous reduced-activation steels. (orig.).

International Nuclear Information System (INIS)

Past elastic-plastic fracture studies for leak-before-break (LBB) assessment of low alloy steel pipings have been focused mostly on the behavior of base metals and their weld metals. In contrast, the heat-affected zone (HAZ) of a welded pipe has not been studied in detail primarily because the size of the HAZ is too small to make specimens for mechanical properties measurements. In this study, microstructural analyses, microhardness tests, tensile tests and J-R tests have been conducted as a function of distance from a fusion line and temperature for HAZ materials of SA106Gr.C low alloy piping steels. For the ferrite-pearlite steels such as SA106Gr.C, the HAZ specimens showed a higher yield strength and fracture toughness compared with those of its base metal. These characteristics, despite of grain coarsening, can be explained by cleaner microstructures of HAZ materials with a finer morphology of carbides compared with pearlitic-ferritic base ...

International Nuclear Information System (INIS)

Ferritic/martensitic steel, modified 9Cr-1Mo steels have been used most extensively in the power generation industry throughout the world due to having superior high temperature properties such as high strength, creep resistance, and good microstructure stability. These steels are also the primary candidate for the RPVs(Reactor Pressure Vessels) of High Temperature Gas-Cooled Reactors. Currently, many studies has been conducted in laboratory-scale for mod. 9Cr-1Mo steels. However, there is a lack of the study on forged thick- section for RPVs. The differences in characteristics including the through thickness microstructure and mechanical properties between internal and external locations may occur during cooling after austenitization, because the thickness of RPVs is over about 200mm. Therefore, in order to use ferritic/martensitic steel as RPVs, a detailed assessment of the through thickness properties is needed. The purpose of this study is ...

Energy Technology Data Exchange (ETDEWEB)

The report covers the results of exposing materials for steam turbines to increased steam temperatures in two modules of the KOMET 650 testing facility at the Westfalen power plant. Ferritic/martensitic steels with 9 to 12% Cr and austenite and nickel-based alloys were investigated. Some experimental coatings on low-alloy Cr steel were also tested. The principal findings are presented. It will become possible to construct advanced power stations to be operated at higher temperatures. (orig.)

International Nuclear Information System (INIS)

A preliminary investigation was completed on the characterization and decontamination of coral samples from Johnston Island. These samples were found to contain individual particles (2 to 0.25 mm) of contaminated coral as well as a piece of contaminated magnetic metal. They ranged in activity from about 70 to 811 nCi Am-241. The decontamination methods investigated were froth flotation, ferrite treatment, attrition scrubbing, ultrasonic treatment and dry sieving. Dry sieving, the more effective technique, separated about 42 wt % of the coral into a decontaminated fraction. This fraction (>4 mm) contained about 0.5% of the total activity. 7 refs., 3 tabs.

UK PubMed Central (United Kingdom)

The metal parts of cardiac valve prostheses cause reactions in the surrounding tissues of the heart. In some dogs rather abnormal reactions were found, and were attributed to corrosion of the stainless...Full Text Available

Science.gov (United States)

Mar 13, 2003 ... dryer, $95; cooktop, drop-in, 30 , stainless steel, $75. 837-6649. 5 Two tickets to Broadway Theatre. League play, South Pacific, Orchestra, ...

British Library Electronic Table of Contents (United Kingdom)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr2N, CrN, TiN, V2N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited...

International Nuclear Information System (INIS)

Plasma nitriding in glow discharge is a process of modifying surface properties of a material by which surface hardness, corrosion resistance, fatigue strength etc. of a material can be improved

Energy Technology Data Exchange (ETDEWEB)

The open circuit potential (OCP) of stainless steels immersed in natural waters generally increases with time. This phenomenon is strongly linked to the formation of a bio-film on the surface. Several studies have proved that the bio-film modifies the reaction of reduction of dissolved oxygen and that it acts mainly on the cathodic processes. One of the hypotheses explaining the action of the bio-film involves certain bacteria which use dissolved oxygen and extracellular enzymes to produce reactive oxygen species. Among this kind of metabolites is hydrogen peroxide H{sub 2}O{sub 2}. This compound interacts with the passive layer of stainless steels and affects their electrochemical behaviour, even when the chloride concentration is low. The aim of this work is to study the influence of an enzymatic reaction (of the oxidoreductase type) on anodic and cathodic processes on AISI 316L stainless steel. Experiments are carried ...

Energy Technology Data Exchange (ETDEWEB)

The methodology of the drip procedure of the Standard Test Method for Evaluating the Influence of Thermal Insulation on External Stress Corrosion Cracking Tendency of Austenitic Stainless Steel (ASTM C 692-95a) was used to research the effect of halogens and inhibitors on the external stress corrosion cracking (ESCC) of Type 304 stainless steel as it applies to the insulation industry. Simulated insulation extraction solutions were made with pure chemical reagents for the halogens and inhibitors. The results indicated that sodium silicate compounds that were higher in sodium were more effective for preventing chloride-induced ESCC in Type 304 austenitic stainless steel. Potassium silicate was not as effective as sodium silicate. Fluoride, bromide, and iodide may cause ESCC but they were much less active than chloride and could be effectively inhibited by sodium silicate compound. The addition of fluoride ions to the ...

International Nuclear Information System (INIS)

Thin passive films formed on highly corrosion-resistant type-312L stainless steel, containing 20 mass% chromium and 6 mass% molybdenum, in 2 mol dm-3 HCl solution at 293 K have been analyzed by glow discharge optical emission spectroscopy (GDOES). The stainless steel does not suffer pitting corrosion even in this aggressive solution, showing a wide passive potential region. The depth profiles obtained clearly show a two-layer structure of the air-formed and passive films: an outer iron-rich layer and an inner layer highly enriched in chromium. Alloy-constituting molybdenum is deficient in the inner layer of the passive films and is enriched in the outer layer, particularly at the active dissolution potential. The molybdenum species in the outer layer may retard the active dissolution of stainless steel, promoting the formation of stable passive films highly enriched in chromium. Chloride ions are present only at the ...

Energy Technology Data Exchange (ETDEWEB)

The formation and breakdown of the passive films on stainless steels are mainly controlled by ionic and electronic transport processes. Both these processes are in part controlled by the electronic properties of the oxide film. Consequently, it is vital to gain a detailed perception of the electronic properties of the passive films together with structural and compositional information for a comprehensive understanding of mechanisms behind passivity and localised corrosion. As a step towards this goal the passive films formed on two main austenitic stainless steels AISI 316L and AISI 304L in borate solution were characterised by in situ Raman spectroscopy and photocurrent spectroscopy coupled with electrochemical measurements. This revealed the formation of an Fe-Cr spinel as the dominant constituent in the passive films with more Cr enrichment in the oxide film on 316L than that of 304L. Bandgap readings and semiconductivities of the two ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical dissolution behaviour of armco-iron and of the steels C15, C45, C60 and 100Cr6 in concentrated sodium chloride media has been investigated. Anodic metal dissolution experiments have been carried out using the flow channel cell (parallel plate reactor), the rotating cylinder electrode (RCE) and the capillary cell. The microstructure of the steel has been varied through variation of carbon content and heat treatment (e.g. soft annealed with globular carbides or pearlitic). Current-efficiency values have been obtained by gravimetric measurements in the current-density range from i=5 to 60 A/cm{sup 2}. For the soft annealed steels, the divalent ferrite dissolution in combination with electroless cementite removal dominates. For the pearlitic steels, the occurrence of oxygen evolution electronically conductive metal carbides or trivalent ferrite dissolution, depending on the current density applied, was detected. Microstructure ...

DEFF Research Database (Denmark)

It is shown that multipole dislocation configurations can arise during power-law creep of certain austenitic stainless steels. These multipoles have been analysed in some detail for two particular steels (Alloy 800 and a modified AISI 316L) and it is suggested that they arise either during instantaneous loading or during the primary creep stage. Trace analysis has shown that the multipoles are confined to {1 1 1} planes during primary creep but are not necessarily confined to these planes during steady-state creep unless they are pinned by interstitials.

Energy Technology Data Exchange (ETDEWEB)

17-4PH stainless steel was modified by direct current (DC) plasma nitriding and titanium nitride film duplex treatment in this study. The microstructure, wear resistance and corrosion resistance were characterized by X-ray diffraction (XRD), pin-on-disk tribological test and polarization experiment. The results revealed that the DC plasma nitriding pretreatment was in favor of improving properties of titanium nitride film. The corrosion resistance and wear resistance of duplex treatment specimen was more superior to that of only coated titanium nitride film.

International Nuclear Information System (INIS)

This paper presents the main achievements of the European Home Team (EU HT) test programme of ITER primary wall small scale mock ups. It describes briefly the fabrication method of the mock ups, the test conditions and the main results obtained with high heat flux and thermal fatigue tests of Cu alloy/stainless steel and beryllium/Cu alloy/stainless steel mock ups. The results obtained so far show very good thermal fatigue performance and operation margin of the ITER primary first wall concept.

International Nuclear Information System (INIS)

The effects of #alpha# particle irradiation on a passive film formed on a 304 type stainless steel are studied in situ. The experimental arrangement minimizes the radiolysis effects due to the electrolyte. Under irradiation, a modification of the electronic structure of the oxide layers is revealed by photo-electrochemistry and impedance measurements. The influence of irradiation on the corrosion resistance of the passive film is investigated. Comparing the rest potential and the breakdown potential respectively under and without irradiation, a drop in the passivity range under irradiation is shown. this is interpreted as a decrease in the corrosion resistance. (author).

International Nuclear Information System (INIS)

Evolution of the passive films formed on AISI 304L and duplex stainless steel SAF 2205 in NaOH 0.1 M was investigated using cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and X-ray photoelectron spectroscopy (XPS). Special attention is paid to the effect of Mo in the generation of the films. Results point out to the stabilising effect of the molybdates on the surface of the film, enhancing the formation of a thin layer on the SAF 2205 with a higher Cr/Fe ratio.

International Nuclear Information System (INIS)

Visualizations by real-time neutron radiography are demonstrated of various flow patterns of nitrogen gas-water two-phase flow in a stainless-steel tube, water inverted annular flow in a stainless-steel tube, flashing flow in an aluminium nozzle and fluidized bed in aluminium tube and vessels. Photographs every 1/60 s are presented by an image processing method to show the dynamic behaviours of the various flow patterns. It is shown that this visualization method can be applied efficiently to multiphase flow researches and will be applicable to multiphase flows in industrial machines. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper described experiments on the adsorption of radon gas on surfaces of various materials. The experiments were carried out on three kinds of materials: Poly(vinyl chloride), polyethylene and stainless steel. On stainless steel, adsorption was not detectable. On the other hand, there was clearly adsorption on poly(vinyl chloride) and polyethylene. A poly(vinyl chloride) sheet of one square meter surface in a 5.3 L container absorbed approximately 20% of the radon. Radon adsorption has to be taken into account when radon concentration measurements in the air. (author)

International Nuclear Information System (INIS)

In this paper the thermal design of a horizontal steam generator for the Indian PHWR nuclear power plant is described. The main attraction is absence of tube sheet and use of stainless steel 'U' tubes. It is emphasised that with appropriate water chemistry it is possible to use stainless steel tubes, which is many times cheaper than the Incoloy tubes used elsewhere. The design approach, applicable equation for the design and the results of computation in the form of heat transfer area and some important dimensions of the steam generator are presented.

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steels can yield low interfacial contact resistance (ICR), electrically-conductive and corrosion-resistant nitride containing surfaces (Cr2N, CrN, TiN, V2N, VN, etc) of interest for fuel cells, batteries, and sensors. This paper presents the results of scale up studies to determine the feasibility of extending the nitridation approach to thin 0.1 mm stainless steel alloy foils for proton exchange membrane fuel cell (PEMFC) bipolar plates. A major emphasis was placed on selection of alloy foil composition and nitidation conditions potentially capable of meeting the stringent cost goals for automotive PEMFC applications. Developmental Fe-20Cr-4V alloy and type 2205 stainless steel foils were treated by pre-oxidation and nitridation to form low-ICR, corrosion-resistant surfaces. Promising behavior was observed under simulated aggressive anode- and cathode- side bipolar plate conditions ...

Energy Technology Data Exchange (ETDEWEB)

The passive films formed in stainless steels are thin and fine oxide films, a high corrosion resistance can be provided by these films. This study formed SiO2 protective coating on the substrate of SUS 304 stainless steels by chemical vapor deposition using TEOS-O3 system. Firstly, relations of substrate temperature and deposition rate of films, chemical composition, refractive index of films were investigated. Then, the corrosion resistance of SUS 304 stainless steels coated SiO2 films was examined by activation time and an anodic polarization curve in 1 kmol[center dot]m[sup -3] HCl solution. The results were obtained as follows. Thickness of SiO2 films linearly increases with time at the deposition temperature of 473 to 673 K. Si-OH bonds would disappear above the deposition temperature of 573 K, almost perfect SiO2 films were obtained. The activation time in 1 kmol[center dot]m[sup -3] HCl solution increased with ...

International Nuclear Information System (INIS)

Surface analytical studies of high nitrogen austenitic stainless steels exposed to deaerated 0.1M HCl have revealed that nitrogen alloying additions influence the composition of salt layers and the passive film/alloy interface. In this study the authors employ electrochemical techniques and variable angle X-ray Photoelectron Spectroscopy (XPS) to examine the passive films formed on a series of austenitic stainless steels, Fe18Cr8Ni, Fe18Cr8Ni0.2N, Fe20Cr20Ni, Fe20Cr20Ni6Mo and Fe20Cr20Ni6Mo0.2N, in acidic chloride aqueous solution. In addition, several other model alloys, Fe19Cr, Fe19Cr9Ni, Fe19Cr2.5Mo, and Fe19Cr9Ni2.5Mo, were examined before and after electrochemical surface nitriding, a technique proven to have an effect analogous to N alloying. It was shown that nitrogen, nickel and molybdenum additions independently and in certain combinations stimulate selective dissolution of iron, resulting in a significant enrichment of chromium ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the effects of 325nm wavelength ultraviolet light irradiation on pitting corrosion behavior of type 340 stainless steel in a neutral chloride solution are studied. Further, the change of passive film with the light irradiation is analyzed using x-ray photoelectron spectroscopy. The mains results obtained therefrom are stated below. Pitting potential can be shifted in noble direction by the ultraviolet light irradiation. The effect of ultraviolet light irradiation is ore prominent in the pitting corrosion process than that in the passive film formation. The result of the analysis in terms of the birth and death stochastic probability process shows that pitting corrosion rate is decreased remarkably by the ultraviolet light irradiation at the formation of passive film, while the repassivation is slightly expedited by the ultraviolet light irradiation. On the other hand, the repassivation rate is increased a little by the ultraviolet light irradiation ...

Energy Technology Data Exchange (ETDEWEB)

A dense and supersaturated nitrogen layer with higher conductivity is obtained on the surface of austenitic stainless steel 304L by the low temperature plasma nitriding. The effect of plasma nitriding on the corrosion behavior and interfacial contact resistance (ICR) for the austenitic stainless steel 304L was investigated in 0.05M H{sub 2}SO{sub 4}+2ppm F{sup -} simulating proton exchange membrane fuel cell (PEMFC) environment using electrochemical and electric resistance measurements. The experiment results show that the stable passive film is formed after the potentiostatic polarization at the specified anodic or cathodic potentials under PEMFC operation condition, and the plasma nitriding improves slightly the corrosion resistance and decreases markedly the ICR of 304L. The ICR of the plasma nitrided 304L increases after the potentiostatic polarizations for 4h, and lower than 100m{omega}cm{sup 2} at the compaction force of 150Ncm{sup -2}. ...

Energy Technology Data Exchange (ETDEWEB)

It was to be investigated why inexplicable cracking occurred in plain stainless austenitic steel pipes of heat exchangers in discrete sites of the inner surface exposed to acid even with anodic corrosion protection, and what countermeasures must be taken. The following materials were investigated: X 6 CrNiTi 18 10 and X 6 CrNiMoTi 17 12 2. The influence of mechanical vibrations on passive film formation and destruction was investigated in unconstrained pipes and pipes constrained at one end in conditions of anodic protection at frequencies of 0 to 160 Hz and temperatures of 98 to 130 degrees Centigrade in 98% sulphuric acid. The authors were unable to reconstruct the cracks observed in practical operation in anodically protected heat exchanger pipes of stainless austenitic steel. (orig./MM). 5 refs., 2 tabs., 71 figs.

Energy Technology Data Exchange (ETDEWEB)

A low-molybdenum austenitic stainless steel (UNS S30100) has been surface implanted with molybdenum ions, using various doses of 50 keV and 140 keV ions at room temperature. It is found that in aqueous sulphate/chloride solutions similar to the constitution of sea-waters the implantation does not affect the potentiostatically-determined critical pitting potential, but does change the density and morphology of corrosion pits. Pitting initiation after the addition of chloride at a fixed potential indicates little change in the time for measurable current increase, but the rate of increase of the current is much lower for implanted material. Detailed examination using optical microscopy, scanning electron microscopy, transmission electron microscopy and selected area diffraction suggests that the pits produced in implanted material are hemispherical with smooth covers of unattacked alloy. The use of half-implanted samples demonstrates that molybdenum implantation ...

Science.gov (United States)

Using an expanded nuclear data base, the transmutation of PCA, AMCR33 (a reduced activation austenitic steel), HT-9, Rafer2 (a reduced activation ferritic steel), V-15%Cr-5%Ti alloy, and SiAlON (a ceramic) were calculated for two positions in the Fast Flux Test Facility (FFTF), three positions in the High Flux Isotope Reactor (HFIR), and the first wall position of both the STARFIRE and MARS conceptual fusion reactors. The peripheral test (PTP) position, and to a lesser extent the radial beryllium (RB) position, of HFIR show significant transmutations which are often in the opposite direction to the transmutations in the fusion conceptual designs. The positions in FFTF, as well as the hafnium covered location in the HFIR RB position show relative minor transmutations.

British Library Electronic Table of Contents (United Kingdom)

Irradiation of EP-823 (16Cr12MoWsiVNbB) ferritic-martensitic steel with 7-MeV Ni++ ions and with 30- and 70-keV He+ ions at a temperature of 500?C was followed by an increase in the microhardness, which was due to both radiation point defects and changes in the phase composition and the dislocation structure of the steel. It was found that the dependence of the largest relative increase in the microhardness on the concentration of radiation-induced point defects in the near-surface region of the steel under irradiation with different ions correlated with an analogous dependence of the surface segregation of silicon and chromium.

Energy Technology Data Exchange (ETDEWEB)

There have been many stress measurements on welds by neutron diffraction over the past 20 years but there are still a number of serious experimental issues that are often not addressed. The primary fact is that the microstructure generally changes across the weld and accompanying this may be a change in the concentration of strengthening elements in solution. This will lead to a shift in lattice spacing which may be incorrectly interpreted as a strain. Secondly, a gradient of plastic deformation near the weld may be expected. Since plastic deformation by application of a stress always generates intergranular (type-2) strains this may lead to a range of intergranular effects superposed on the conventional weld-related strains. The effects are illustrated by neutron diffraction studies of Zr-4, ferritic and austenitic welds where chemistry, intergranular effects and crystallographic texture can all play a role.

British Library Electronic Table of Contents (United Kingdom)

This paper presents a procedure for transferring the CTOD fracture toughness obtained from laboratory specimens to an equivalent CTOD for structural components, taking constraint loss into account. The Weibull stress criterion is applied to correct the CTOD for constraint loss, which leads to an equivalent CTOD ratio, b, defined as b=d/dWP, where d and dWP are CTODs of the standard fracture toughness specimen and the structural component, respectively, at the same level of the Weibull stress. The CTOD ratio b is intended to apply to the fracture assessment of ferritic steel components to stress levels beyond small-scale yielding. Nomographs are given to determine the b-value as a function of the crack type and size in the component, the yield-to-tensile ratio of the material and the Weibul...

International Nuclear Information System (INIS)

The magnetic and magnetostrictive properties of polycrystalline Co1-xMnxFe2O4 (0 ? x ? 0.4) have been studied. Although the Curie temperature decreases continuously with increasing concentration of Mn, the magnetization remains high up to x = 0.3 and unexpectedly low coercivity is observed for this composition showing an unusual magnetostrictive behaviour. This composition shows a relatively larger magnetostriction at low fields. Moreover, the strain derivative which is the slope of the magnetostriction curve at low magnetic fields is almost doubled and the field at which maximum magnetostriction is observed is reduced to almost half for 30% of Mn substitution. The results show that x ? 0.3 in Co1-xMnxFe2O4 is an optimum composition with superior magnetostrictive properties for many applications.

Energy Technology Data Exchange (ETDEWEB)

The preliminary design of a far-infrared free-electron laser with a Coaxial Hybrid Iron (CHI) wiggler is presented. The CHI wiggler consists of a central rod and outer ring of alternating ferrite and dielectric spacers. A periodic wiggler field is produced when the CHI structure is immersed in an axial magnetic field. The design under investigation makes use of 1A, 1MV annular electron beam interacting with the TE{sub 01} coaxial waveguide mode at approximately 1 THz ({lambda} = 300 {mu}m). The nominal wiggler period is 0.5 cm and the inner and outer waveguide radii are 0.4 and 0.8 cm, respectively. An axial guide field of 5-10 kG is used. The device performance is modeled with slow-time-scale nonlinear code. Self fields and axial velocity spread are included in the model. Theoretical results will be presented.

Energy Technology Data Exchange (ETDEWEB)

Very good friction and wear measurements are reported for MRCC (metal reinforced carbon composites), made from low-wear non-graphitic carbon matrix with metal-fiber reinforcement. Counterfaces include austenitic and martensitic stainless steels, Si nitride, and alumina. Effects of high load, high temperature, and gaseous environments are reported: removal of humidity, atm. oxygen have little effect on friction, wear for MRCC sliding against ceramic or stainless steel. Wear of Al oxide riders on MRCC is very low, not affected by contact load. 260 C temperatures do not degrade performance of 440-C riders on MRCC disks or raise friction. In small or large sizes, MRCC is made in a single-pass process for about the same volume cost as cast iron. It can survive heating in nitrogen above 1600 C without loss of integrity or major change of dimensions.

International Nuclear Information System (INIS)

Moss-Schottky plots and photoelectrochemical measurements were made on films formed at different potentials on AISI 304 stainless steel in a borate/boric acid solution, pH 9.2. The results allowed the determination of the semiconductive properties and band structure of the films, which account for the existence of two kinds of films depending on the formation potential. For potentials below 0 V (SCE), the results point out for a film with an inverse spinel structure constituted by Cr-substituted magnetite with two donor levels. Above 0 V only one donor level is detected, which should be Fe"2 "+ on tetrahedral sites.

Energy Technology Data Exchange (ETDEWEB)

The passive films formed on 316L stainless steel in various NaCl solutions have been investigated by capacitance measurements (Mott-Schottky). Pitting parameters have been determined using the galvano-kinetic polarisation method. The obtained results reveal the existence of a shallow and a deep donor level localised in the band gap of the semiconducting oxide film. These energy levels are due to iron ions in the tetrahedral and octahedral positions. It also appears that the participation of the deep donor level effects the electric field. The study developed allows us to compare characteristic parameters of the electronic structure of the passive film to those related to pitting susceptibility. (authors) 25 refs.

Energy Technology Data Exchange (ETDEWEB)

P-implantation (10/sup 17/ ions cm/sup -2/, 40 KeV) into 304 stainless steel (ss) has been carried out, and an amorphous surface alloy was formed. Polarization studies in deaerated 1N H/sub 2/SO/sub 4/+ 2% NaCl showed that P-implantation improved both the general and localized corrosion resistance of 304 ss. A comparative study has been carried out between the implanted and unimplanted steel to determine what influence P-implantation has upon the properties of the passive film formed 1N H/sub 2/SO/sub 4/. The influence of Cl ions on pre-formed passive films was also studied. RHEED, XPS and AES were used to evaluate the nature of the passive films formed in these studies.

Energy Technology Data Exchange (ETDEWEB)

Samples of austenitic stainless steel AISI 316 were nitrided using the cathodic cage technique with the addition of methane in the nitriding atmosphere. The aim was to study the influence of this technique in reducing the precipitation of chromium nitrite and in improving the wear resistance. The results show that there was a significant improvement in such properties when compared to the results of ionic plasma nitriding. Formation of a double layer, one more internal composed of carbon and another with high nitrogen content, was confirmed by Scanning Electron Microscopy (SEM). The microhardness profile of the layer showed an increase in hardness values and a larger uniformity, while X-ray analysis showed less chromium nitriding precipitation when compared with results obtained for samples treated using ionic plasma nitriding.

International Nuclear Information System (INIS)

AISI 316L stainless steel was welded by the electron beam (EB) and laser techniques. Microstructural characteristics, hardness profile, creep rupture properties and creep damage of the welds were investigated. Fully austenitic microstructure was obtained in the two welds. The solidification structure of the welds consisted of the cellular and equiaxed dendrites. The creep rupture lives of the two welds were almost the same, and they were reduced by a factor of about two compared to the base metal. Moreover, the rupture elongation of the welds was lower than that of the base metal. Creep damage was observed in the ''parting'' region of the welds and in the heat-affected zone (HAZ), respectively. Final creep fracture occurred in the ''parting'' region of the welds. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The divertor collector plate in the INTOR reactor will be subjected to high heat, particle, and neutron fluxes, making it the most severely damaged torus component. The collector plate is composed of a protection plate, which is directly exposed to the particle flux, and a heat sink which provides support for the protection plate and carries the water coolant. The high-Z refractory metals have been considered for use as the protection plate material, and austenitic stainless steels and copper alloys have been considered as the heat sink material. Tungsten and Type 316 stainless steels have been selected for the protection plate and heat sink, respectively. The protection plate has a sputtering lifetime of 1.75 y at a 50% duty factor, while the heat sink is expected to last the lifetime of the reactor.

Energy Technology Data Exchange (ETDEWEB)

The surface films formed on type 316LN stainless steels (SS) with different nitrogen contents, during potentiodynamic polarization in acidified 1 M NaCl solution, were characterized by Laser Raman Spectroscopy (LRS). LRS confirmed the presence of oxides and oxychlorides of iron and chromium, hydrated chlorides and nitrates in the film. Raman mapping showed increasing nitrate content in the film with increasing nitrogen content. The film on the uncorroded material showed the presence of chromium and molybdenum oxides. The improvement in pitting corrosion resistance of type 316LN SS with increasing nitrogen content was attributed to increased amount of nitrates in the passive film.

International Nuclear Information System (INIS)

Nickel ion radiation at 500 C was shown to have a strong effect on the surface electrochemistry and intergranular corrosion (IGC) of stainless steel (SS). Measured current densities in a 1 N sulfuric acid solution at room temperature were increased at active-passive, passive, and transpassive potentials. Radiation effects on the current decay behavior and susecptibility to IGC were similar for a fine-grained (FG) S alloy and for a very large-grained (LG) SS. Radiation-induced segregation (RIS) at the surface was believed to promote higher currents at short times, whereas segregation at grain boundaries was responsible for IG attack. Analytical electron microscopy (AEM) measurements revealed chromium and iron depletion plus Ni and silicon enrichment at grain boundaries in irradiated specimens. Si enhanced dissolution at transpassive potentials, whereas Cr depletion did the same at active-passive and passive potentials.

International Nuclear Information System (INIS)

Intergranular corrosion (IGC) resistance of types 304LN and 316LN stainless steels (SS) thermally aged at 823, 873, and 923 K for various durations was assessed by ASTM A262 practice A test (electrolytic etch test) and electrochemical potentiodynamic reactivation (EPR) test. The results indicated that the type 316LN SS has significantly improved IGC resistance compared to 304LN SS. Based on the results of these tests, time-temperature-sensitization (TTS) diagrams were developed for both alloys. The secondary precipitates formed during thermal aging treatments were electrochemically extracted and analyzed by X-ray diffraction (XRD) to determine the types of precipitates formed during the aging treatments. The results indicated that the precipitates were mostly of M_2_3C_6 carbides.

Energy Technology Data Exchange (ETDEWEB)

This paper investigates steels 12Kh18N10T, 10Kh17N13M2T, 08Kh22N6T, and 08Kh21N6M2T. In corrosion of stainless steels in sulfuric acid solutions, dissolved sulfur dioxide acts as a cathodic depolarizer, capable of being reduced to elemental sulfur or forming sulfides with the metal. Depending on the conditions, this is associated with some increase in potential and greater or lesser increase in corrosion or facilitation of passivation of active steel. After passivation the influence of SO/sub 2/ is negligible. The results of this investigation were used as initial data for developing systems of anodic protection for shell-and-tube heat exchangers for sulfuric acid.

International Nuclear Information System (INIS)

The CO laser is superior in the absorption characteristic to materials to the CO2 laser due to its shorter wavelength. In consideration of this characteristic Nuclear Power Engineering Corporation is studying this applicability sponsored by the Ministry of International Trade Industry of Japan to cutting of reactor core internals of commercial nuclear power plant. In decommissioning of reactor core internals it is necessary to cut stainless steel plates of 305 mm thick. The authors cut stainless steel plates of up to 310mm thick in air and those of up to 150 mm thick underwater with a 20kW class laser. Further, models simulating key structural elements of PWR core internals were cut and secondary products to clarify the applicability of the CO laser cutting to reactor core internals were evaluated. (author)

International Nuclear Information System (INIS)

Surface study techniques were used to investigate films on Type 304 stainless steel which were formed during exposure to high purity water at 288"0C. The results indicated that the film chemistry depended strongly upon the concentration of the dissolved O_2 in the water. Films formed in water having 8 ppm O_2 were stoichiometric mixed oxides; whereas those formed in water with 10 ppb O_2 were highly defective oxyhydroxides. The latter films are not as protective as the stoichiometric oxides. Auger electron spectroscopy (AES) and X-ray photoelectron spectroscopy (XPS) were used to investigate the films. (Auth.).

International Nuclear Information System (INIS)

In this work passive films formed in AISI 304 stainless steel were envisaged as semiconductors and studied by means of photoelectrochemistry and Mott-Schottky plots. The passive films were potentiostatically formed at different potentials (0.2-0.8V) in a basic borate/boric acid solution without and with addition of NaCl (0.5 and 1g/l) and at various temperatures in the range 8-60"oC. The influence of these parameters on the photocurrent, quantum efficiency, bandgap energy and density of charge carriers was determined. The results show that the experimental conditions at which the films are formed influence the semiconductive properties of the film, which seem to be related to the higher or lower stability of the film. An Arrhenius type of relationship was also found between the density of charge carriers and temperature, leading to the determination of an activation energy. (author) 13 refs., 7 figs.

Energy Technology Data Exchange (ETDEWEB)

Raman scattering was observed from thin film optical waveguides of cellulose acetate exposed to water vapor from 0% to 100% relative humidity (RH), and from dilute solutions of water in methyl acetate. Spectra of cellulose acetate (CA398, 39.8% acetyl) at low RH and cellulose triacetate (CTA) at low and high RH are consistent with the presence of water monomers that are weakly hydrogen bonded to acetyl C=O groups. Differences between the spectra of water in CA398 and CTA at low RH are attributed to sequential hydrogen bonding involving OH groups in CA398. At high RH, CA398 and CTA (to a lesser extent) show bands attributed to water/water interactions that are similar to those found in sequentially hydrogen-bonded hydrates. CA398 films that are annealed at high temperatures exhibit decreased water/water interactions at high RH. Exposure of CA398 films to D/sub 2/O converts > 90% of all polymer OH groups to OD groups. This indicates that water is accessible to ...

International Nuclear Information System (INIS)

This paper describes a reactor design to facilitate a room-temperature nuclear fusion/fission reaction to generate heat without generating unwanted neutrons, gamma rays, tritium, or other radioactive products. The room-temperature fusion/fission reaction involves the sequential triggering of billions of single-molecule, "6LiD 'fusion energy pellets' distributed in lattices of a palladium ion accumulator that also acts as a catalyst to produce the molecules of "6LiD from a solution comprising D_2O, "6LiOD with D_2 gas bubbling through it. The D_2 gas is the source of the negative deuterium ions in the "6LiD molecules. The next step is to trigger a first nuclear fusion/fission reaction of some of the "6LiD molecules, according to the well-known nuclear reaction: "6Li + D #-># 2"4He + 22.4 MeV. The highly energetic alpha particles ("4He nuclei) generated by this nuclear reaction within the palladium will cause shock and vibrations in the palladium lattices, leading ...

International Nuclear Information System (INIS)

A simple and specific method has been developed for the simultaneous determination of the four major Cinchona alkaloids and their dihydroderivatives and pyridoxine hydrochloride (Vitamin B_6) by high-performance liquid chromatography (HPLC) with fluorescence detection (#lambda#_e_m=420 nm with #lambda#_e_x=330 nm). The chromatographic separation was performed on a Phenomenex Prodigy ODS column (5 #mu#m, 250 mmx3.2 mm i.d.), recommended for basic compounds, under isocratic reversed-phase conditions. The method allowed a good peak shape and an effective resolution of the tested compounds. The extraction of alkaloids from the Cinchona succirubra bark was carried out in mild and fast conditions (ambient temperature, 20 min) by ultrasonication. The procedure showed to be advantageous respect to a reference method, which involved Soxhlet extraction. The results were compared statistically by means of the Student's t-test and the variance ratio F-test; no significant ...

International Nuclear Information System (INIS)

Full text: The transmutation of nuclear waste to reduce the burden on a geological repository is a relevant topic within the Program of Nuclear Safety Research of the Research Centre Karlsruhe. Several studies have confirmed that a high efficiency of transmutation of actinides is reached in fast neutron spectrum reactor system. Therefore, an important effort is dedicated to the study of transmutation strategies with different fast reactors and their associated technologies. Moreover, in international contexts as Generation IV International Forum (GIF) and Sustainable Nuclear Energy Technology Platform (SNETP), fast reactors are considered in the frame of sustainable development of nuclear energy and reduction of waste. The systems that are currently under investigation, in the frame of the different fuel cycle scenarios, are liquid metal cooled and gas cooled fast reactors as well as Accelerator Driven Sub-critical Transmutation devices (ADS). These innovative reactor systems, call for ...

Energy Technology Data Exchange (ETDEWEB)

The influence of high C martensite on the strength and impact behavior of C-Mn-Nb-Al steels has been determined for two distributions: films surrounding the ferrite grains and distinct colonies. In the former case, the impact behavior markedly deteriorated, this deterioration increasing with martensite level. The changes in impact behavior could be explained by regarding the films of martensite as being similar to the brittle grain boundary carbides that are present in ferrite-pearlite steels. These films readily crack, yet are always thick enough to produce a sufficient wide crack to render crack propagation easy. The critical event in fracture then becomes the ability to propagate the cracks through the grain boundaries. The greater the grain boundary coverage by these films, the easier this becomes and the worse is the impact behavior. When the martensite is present as colonies, again the impact performance is seriously impaired, but to a ...

Energy Technology Data Exchange (ETDEWEB)

Holmium doped barium based hexaferrites BaFe{sub 12-2x}Ho{sub 2x}O{sub 19} with (x = 0.0-1.0) were synthesized by solid state reaction method. Structural and magnetic characterization of these ferrites provide significant information about their reactive physical properties. X-ray analysis reveals that in all samples M-type structure exist with few secondary phases. Scanning electron microscope revealed the grain size of the specimen. The results show that grain size decreases with the substitution degree of Holmium. Thus rare earth element Holmium Ho{sup 3+} acts as a grain growth inhibitor. The magnetic hysteresis loops show the variation in the values of magnetic parameters like saturation magnetization (M{sub s}), remanent magnetization (M{sub r}) and coercivity (H{sub c}) were observed by changing Ho{sup 3+} content in BaFe{sub 12-2x}Ho{sub 2x}O{sub 19} ferrites. Coercivity showed a maximum value of 2230 Oe for (x = 0.4) and then ...

Energy Technology Data Exchange (ETDEWEB)

Outline: Discuss far-side weld problem and phased array techniques applied. Describe laboratory work on flawed piping specimens using L- and S-wave arrays and provide synopsis of results. Discuss conclusions ofr capability of phased array as applied to austenitic welds. Research Approach: Evaluate phased arrays on unifornly-welded piping specimens. Apply best methods to non-uniform welds. Correlate acoustic responses as function of weld microstructures.

Energy Technology Data Exchange (ETDEWEB)

This Conference paper is for submission to the 7th International Conference on NDE in Relation to Structural Integrity for Nuclear and Pressurized Components, in Yokohama, Japan Specifically, this paper is being presented at this Conference on May 12-14, 2009.

Energy Technology Data Exchange (ETDEWEB)

Thermal (gas) nitridation of stainless steel alloys can yield low interfacial contact resistance (ICR), electrically conductive and corrosion-resistant nitride containing surface layers (Cr{sub 2}N, CrN, TiN, V{sub 2}N, VN, etc.) of interest for fuel cells, batteries, and sensors. This paper presents results of proton exchange membrane (PEM) single-cell fuel cell studies of stamped and pre-oxidized/nitrided developmental Fe-20Cr-4V weight percent (wt.%) and commercial type 2205 stainless steel alloy foils. The single-cell fuel cell behavior of the stamped and pre-oxidized/nitrided material was compared to as-stamped (no surface treatment) 904L, 2205, and Fe-20Cr-4V stainless steel alloy foils and machined graphite of similar flow field design. The best fuel cell behavior among the alloys was exhibited by the pre-oxidized/nitrided Fe-20Cr-4V, which exhibited {proportional_to}5-20% better peak power output than untreated ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this research is to gain a better understanding of the corrosion of the aluminized type 316 stainless steel employed in the seal areas of the molten carbonate fuel cell. The seals are formed between the aluminized Type 316 SS surface and the electrolyte (generally a mixture of molten alkali carbonates and lithium aluminate).

International Nuclear Information System (INIS)

We report the oxygen, hydrogen, and deuterium effects on nitrogen implantation of stainless steel. Oxygen is absorbed on the surface creating a potential barrier and diminishing the nitrogen retention. Deuterium removes more oxygen from the surface than hydrogen, augmenting the nitrogen chemical potential and yielding faster nitrogen diffusion into the bulk material.

Science.gov (United States)

Ti-Pd-Ag, Ni-Cu-Sn. Back cover. Tedlar, mylar, T-P-T. Tedlar, T-P-T, glass, i. T -AI-T. P-AI-T, T-AI-T,white RTV. Frame. AI, stainless steel ...

British Library Electronic Table of Contents (United Kingdom)

The review provides a general idea about the types of metallic alloys and the pure metals used as implant materials in dental and orthopedic surgery. Their corrosive behavior in both real solutions and various media that model human biological fluids is described. Based on the literature data, it is concluded that multicomponent alloys containing titanium, niobium, zirconium, tungsten, molybdenum, aluminum, and silicon are the most resistant to corrosion. Implants made of different types of stainless steel are preferred when manufacturing orthopedic devices for short-term use.

International Nuclear Information System (INIS)

An improved coating for Advanced Gas Cooled Nuclear Reactor austenitic stainless steel fuel cans is described which, tests have shown, inhibits the deposition of carbon on the cans in carbon-containing ionising radiation environments. The coating comprises a refractory oxide which has been prepared by a vapour phase condensation method, in combination with a noble metal. (U.K.).

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work was to establish the flammability limits of hydrogen in air for upward vertical flame propagation at elevated temperatures up to 350 deg and atmospheric pressure in a conventional stainless steel test tube apparatus, and to investigate the extent to which a prolonged exposure (i.e., residence time) of the mixture to elevated temperatures before spark ignition may influence the value of the flammability limits. 9 refs.

International Nuclear Information System (INIS)

A historical overview of corrosion problems found in power plant condensers and mitigation procedures is presented. The paper is organized according to alloy type and failure mode. Alloys considered are copper-base alloys, stainless steels and titanium. Failure modes discussed include erosion-corrosion, sulfide attack, environmentally assisted cracking, galvanic corrosion, steam condensate corrosion, pitting corrosion, and dealloying. Mitigation procedures discussed include cathodic protection, ferrous ion injection, as well as tube cleaning and layup practices.

International Nuclear Information System (INIS)

Constant pull rate tests were conducted on tensile specimens of Inconel Alloy 600, Incoloy Alloy 800, and Type 304 stainless steel in deaerated 10% NaOH solution at 288 C (550 F) with a cover gas of 5% H_2 in N_2. The pull rate used for most experiments was 3.3 x 10"-"6 cm/s, which corresponds to an initial strain rate of 3 x 10"-"6 s"-"1. The electrical potential of the specimens was controlled by a potentiostat using a nickel wire as a hydrogen reference electrode. Under open circuit conditions, Type 304 stainless steel specimens cracked rapidly, but Alloys 600 and 800 specimens exhibited only ductile fracture. However, cracks readily formed in Alloy 800 specimens at potentials in the +50 to +300 mV range and in Alloy 600 specimens at potentials in the +150 to +250 mV range. Scanning electron microscope (SEM) photographs of some of the cracked specimen surfaces showed the transition from ductile to brittle fracture as a consequence of changes ...

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion and trans-passive dissolution of 316 stainless steel in solution containing five percent of commercial bleaching liquid was investigated by employing potentiodynamic polarization method and recording corrosion potential during immersion. Today commercial bleaching liquids are widely used as cleaner additives, therefore, those house appliances made from stainless steels are in contact with aqueous solution containing bleaching liquid. This may cause sever localized corrosion and trans-passive dissolution. In order to investigate the possibility of trans-passive dissolution of stainless steel by bleaching liquid, potentiodynamic polarization and recording variation of corrosion potential of specimens were carried out in 0.2 M Na{sub 2}SO{sub 4} solution containing 5 %wt. commercial bleaching liquid. A 500 mV drop in trans-passive potential and also instantaneously ennobling corrosion potential revealed the ...

Energy Technology Data Exchange (ETDEWEB)

In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the accuracy. Polysulphide and ...

International Nuclear Information System (INIS)

The influence of chemical composition and heat treatment on a low-carbon steel, chromium steel and high speed steel has been examined by polarisation curves and electrochemical parameters deduced from the Tafel plots. The electrochemical corrosion resistance, which is small between the as-received steels become greater after heat treatment, following the order: carbon steel < chromium steel #approx# high speed steel. To explain these differences, the nano- and microstructure of the steels has been characterized by the ex situ techniques of atomic force microscopy and optical microscopy, before and after surface etching with Nital (a solution of 5% HNO_3 in ethanol). This causes preferential attack of the ferrite phases showing the carbide phases more clearly. From these nanostructural studies it was possible to better understand why the passive films formed on chromium steel and high speed steel have superior protective properties to those formed on carbon ...

International Nuclear Information System (INIS)

The results of a combined investigation of splat-quenched Fe-Csub(x) (x<0.05) alloys by resistivity, X-ray diffraction and Moessbauer spectroscopy are presented. The residual resistivity increases linearly with the carbon content (#DELTA#rho=5#mu##OMEGA#cm/at.%) with a slope identical to that observed in the dilute ferritic phase. X-ray diffraction reveals the presence of a martensite structure in addition to a small fraction of residual austenite; the dependence of the a and c lattice parameters on xsub(c) agrees with earlier measurements. A detailed investigation of the relative reflexion intensities shows that the as-quenched martensites consist of a mixing of massive martensite and tetragonal martensite for low carbon content and of tetragonal martensite only for xsub(c) approximately 0.05. The Moessbauer spectra reveal 3 or 4 magnetically non equivalent iron sites. From a detailed analysis of the intensity dependence of the subspectra on carbon content the ...

Energy Technology Data Exchange (ETDEWEB)

A 9Cr-1Mo steel with properties improved over other ferritics in the ranges from 9 to 12% Cr and 1 to 2% Mo and over the widely used 2 1/2 Cr-1Mo steel has recently been developed. The main changes in the modified alloy, compared with the standard alloy, include: addition of niobium and vanadium, to improve the alloy's elevated-temperature strength properties; a specified range for each element; and a specification for nitrogen, which is not listed for the standard 9Cr-1Mo. Microstructural work has indicated that the improved strength of the modified alloy comes from two factors: (1) fine M/sub 23/C/sub 6/ precipitate particles nucleate on Nb/C, N, which comes out first during the heat treatment; and (2) the vanadium enters M/sub 23/C/sub 6/ and retards its growth at the service temperature. Mechanical properties discussed were Charpy-impact, tensile, and creep properties. Other properties included were: thermal expansion coefficient, fatigue tests, steam ...

British Library Electronic Table of Contents (United Kingdom)

Holmium doped barium based hexaferrites BaFe12-2xHo2xO19 with (x=0.0-1.0) were synthesized by solid state reaction method. Structural and magnetic characterization of these ferrites provide significant information about their reactive physical properties. X-ray analysis reveals that in all samples M-type structure exist with few secondary phases. Scanning electron microscope revealed the grain size of the specimen. The results show that grain size decreases with the substitution degree of Holmium. Thus rare earth element Holmium Ho^3^+ acts as a grain growth inhibitor. The magnetic hysteresis loops show the variation in the values of magnetic parameters like saturation magnetization (Ms), remanent magnetization (Mr) and coercivity (Hc) were observed by changing Ho^3^+ content in BaFe12-2xH...

Energy Technology Data Exchange (ETDEWEB)

Corrosion of several materials including pure metals Fe, Ni, Cr and also Fe-Cr, Fe-Ni-Cr alloys, has been studied in anisothermal Pb17Li (Tmax = 500 deg C; {Delta}T = 60 deg C). The corrosion rate of pure nickel is two orders of magnitude higher than the chromium one and about three orders of magnitude higher than the iron one. Fe-Cr alloys (1.4914) suffers a dissolution rate equal to the one of its major constituent, iron. With regard to the three austenitic materials (316L and NS20 steels, alloy 800), they exhibit a porous corrosion layer mainly constituted of ferrite but containing also a small amount of {sigma} phase in the case of the alloys with higher Ni content, NS30 steel and alloy 800. Mechanism of formation of this layer is discussed.

Energy Technology Data Exchange (ETDEWEB)

The precipitation hardened, ferrite-pearlite medium-carbon steels microalloyed with vanadium (AFP steels) have been developed over the last few years as materials allowing processing by controlled, continuous cooling down from forging temperatures, for achieving benefits such as reducing the number of required heat treatment and working processes and saving expensive alloying materials. Due to their cost-saving advantages, the steels rapidly have been accepted as an alternative material to the quenched and tempered steels and re particularly used for fabrication of automobile parts. Their drawbacks however are the lower yield strength, and low ductility and toughness as compared to the heat-treatable steels. The research project therefore was intended to enhance the properties of the microalloyed, medium-carbon steels and widen their applicability by establishing further and improving existing thermomechanical treatment processes that will considerably improve the ...

Energy Technology Data Exchange (ETDEWEB)

Austenitic stainless steels have been implanted with molybdenum ions (Mo[sup +], 100 keV, 2.5 x 10[sup 16] atoms cm[sup -2]). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of [approx] 1000 A with a maximum molybdenum concentration of [approx] 9 at.% Mo located at [approx] 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H[sub 2]SO[sub 4] have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer ...

International Nuclear Information System (INIS)

Critical experiments have been analyzed to verify a nuclear analysis system for fast reactors used in Japan Nuclear Cycle Development Institute (JNC). The experiments were performed in a collaboration work between JNC and the Institute of Physics and Power Engineering of Russia to dispose Russian surplus weapons plutonium, focusing on the effect of the introduction of uranium-plutonium mixed-dioxide (MOX) fuel and stainless steel reflector into the current BN-600 core that is comprised of UO_2 fuel and blanket. The analysis results agreed well with measured values on most of the nuclear characteristics. The accuracies are comparable to those obtained for the conventional MOX fueled fast reactors. It suggests that the JNC analysis system can analyze accurately nuclear characteristics in uranium fueled cores as well. A significant improvement was achieved on the sodium void reactivity by employing an ultra fine group cell calculation system. A change in adjoint ...

International Nuclear Information System (INIS)

The present design of Blanket Shield and Primary Wall for ITER envisages construction of the wall with a water cooled, stainless steel outer layer and a water cooled, copper liner on the inside plasma facing surface. Protection of the inner copper surface with an armour layer is necessary to cope with plasma to wall interaction. There are a number of armour materials under consideration, for this project beryllium was used. The scope of work was to produce a series of mock-ups, each consisting of a different combination of materials, which included Dispersion Strengthened Copper, Copper-Chrome-Zirconium alloy, Beryllium and Stainless Steel. Hot Isostatic Pressing (HIP) was the method used to ensure that a fully diffused bonded joint was achieved giving the necessary strength and thermal conductivity. The first five of the mock ups have been successfully completed and are being tested at the various laboratories in Europe. The remaining mock ups ...

Energy Technology Data Exchange (ETDEWEB)

This work was initiated to examine the effect of frequency and treatment temperature on the formation of nitrided layers and surface characteristics during plasma nitriding. Plasma nitriding experiments were performed with 316L austenitic stainless steel at the temperatures 400 .deg. C and 500 deg. C using a pulsed d.c. plasma with various frequencies in an atmosphere of N{sub 2}-H{sub 2} gas mixture. The microstructure and thickness of the nitrided layer and morphology of the nitrided surface were investigated using OM, SEM, XRD, EDS and AFM. XRD patterns revealed that the surface layer formed at 400 deg. C consisted of S phase only and CrN+Fe{sub 4}N nitrides at 500 .deg. C and no change of phase composition with frequency was observed. The compound layer thickened slightly with increased frequency. Also, the surface roughness increased as the frequency of the pulsed plasma increased from 50 to 5,000Hz.

International Nuclear Information System (INIS)

This paper deals with the characterization of passive films formed on stainless steel (26% Cr and 0 to 3%Mo). The influence of the applied passivation potential and the effect of molybdenum additions to steel upon the composition profiles of passive films formed in an aqueous NaCl solution (3.5% at pH 2.5) are studied. The technique involved is Auger electron spectroscopy combined with ion sputtering. Some electrochemical techniques have been used in conjunction. A quantitative approach of the Auger spectra during the progressive removal of the passive film is described. The peak-to-peak height of the Auger lines are treated in order to yield the atomic fraction of the various elements present in a given subsurface layer. The analytical study of the film by electron spectroscopy indicates that molybdenum plays a part at the metal-oxide interface where this element acts on the chromium diffusion process. This phenomenon, which depends on the imposed potential, may ...

Energy Technology Data Exchange (ETDEWEB)

Passive films, formed on annealed and cold worked AISI 304 stainless steel in hot chloride media, were examined using polarization resistance and impedance measurements. The obtained results show the influence of cold work on film conductivity, which can be correlated to conditions of susceptibility to stress corrosion cracking. Capacitance measurements, using the Mott-Schottky approach, revealed that a change from n to p type semi-conductivity is associated to susceptible conditions with an increase in the doping density estimated for cold worked samples in the presence of chloride. It is assumed that p-type semi-conductivity of the passive film together with the position of the flat band potential has a strong influence on the dissolution processes at the corrosion potential. Based on this analysis the influence of plastic deformation, at the dislocation scale, is discussed. (authors)

Energy Technology Data Exchange (ETDEWEB)

Direct current (DC) glow discharge plasma nitriding was carried out on three selected surface-roughened AISI 304 stainless steel samples at 833 K under 4 mbar pressures for 24 h in the presence of N{sub 2}:H{sub 2} gas mixtures of 50 : 50 ratios. After plasma nitriding, the phase formation, case depth, surface roughness, and microhardness of a plasma-nitrided layer were evaluated by glancing angle x-ray diffractogram, optical microscope, stylus profilometer, and Vickers microhardness tester techniques. The case depth, surface hardness, and phase formation variations were observed with a variation in initial surface roughness. The diffraction patterns of the plasma-nitrided samples showed the modified intensities of the {alpha} and {gamma} phases along with those of the CrN, Fe{sub 4}N, and Fe{sub 3}N phases. Hardness and case depth variations were observed with a variation in surface roughness. A maximum hardness of 1058 Hv and a case depth of 95 {mu}m were ...

International Nuclear Information System (INIS)

As a hardening process, the attractiveness of nitriding lies in its low treatment temperature. Although the thickness of the case is less than that obtained by higher temperature processes such as carburising, there are a range of alloys and applications for which nitriding is the only possible alternative. Indeed, there are some alloys and applications for which even the normal nitriding temperatures (between 500 deg C and 600 deg C for ferrous alloys) are too high. In this paper, we report on developments, specifically the use of low pressure plasmas and high energy ion bombardment, which can extend the benefits of nitriding to lower temperatures. In this poster, we will present results from these collaborative projects, concentrating on the nitriding of austenitic stainless steel at temperatures below 450 deg C. In this temperature range, the hardness and wear resistance of the surface can be improved without compromising the corrosion resistance of the ...

International Nuclear Information System (INIS)

Research highlights: #-># Welding parameters affect pitting corrosion resistance of AL-6XN laser welds. #-># Lower heat input laser welds correspond to higher critical pitting temperature. #-># Depletion of Mo and Cr at dendrite cores causes preferential pitting corrosion. #-># Local Mo level at dendrite cores dominates weld pitting corrosion susceptibility. #-># Lower heat input laser welds manifest lower degree of microsegregation of Mo. - Abstract: Pitting corrosion resistance of laser welds of AL-6XN superaustenitic stainless steel (SASS) was investigated in acidic chloride ion medium. It was found that the critical pitting temperature (CPT) of the laser welds increased with increasing welding speed or decreasing laser power. Pitting attack preferentially occurred at selective dendrite cores of the laser welds. Analytical electron microscope (AEM) microanalysis revealed that depletion of Mo at dendrite cores due to microsegregation is the basic ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, we report on a series of experiments designed to study the influence of plasma nitriding on the mechanical properties of austenitic stainless steel. Plasma nitriding experiments were conducted on AISI 304L steel in a temperature range of 375-475 C using pulsed-DC plasma with different N{sub 2}-H{sub 2} gas mixtures and treatment times. Firstly the formation and the microstructure of the modified layer will be highlighted followed by the results of hardness measurement, adhesion testing, wear resistance and fatigue life tests. The modified surface was analyzed directly after plasma nitriding as well as using a depth profiling method. The microhardness after plasma nitriding is increased up to 19 GPa, that is a factor of five higher compared to the untreated material (3.3 GPa). The adhesion is examined by Rockwell indentation and scratch test. No delamination of the treated layer could be observed. The wear rate after plasma nitriding is significantly ...

Energy Technology Data Exchange (ETDEWEB)

A series of plasma nitriding experiments has been conducted on AISI 304L austenitic stainless steel at temperatures ranging from 375 to 475 C using pulsed-DC plasma with different pulse duty cycles, N{sub 2}-H{sub 2} gas mixtures and treatment times. It is shown that a wide range of treatment parameters exist that allow the formation of the S-phase. The formation and growth of this surface layer depend strongly on the treatment parameters, such as nitrogen partial pressure and duty cycle. Within the parameter range investigated, the layer growth appears to be diffusion controlled with an activation energy about 107 kJ/mol. The formation of CrN precipitates during plasma nitriding is not accompanied by the formation of bcc iron, which might be expected due to the loss of free chromium. However, the S-phase transforms into CrN and bcc iron following a heat treatment at 450 C or higher for 25 h. The wear rate after plasma nitriding is greatly reduced compared with the ...

Energy Technology Data Exchange (ETDEWEB)

Type 440C stainless steel is a high-C, high-Cr martensitic steel used in applications requiring high hardness and wear resistance in combination with moderate corrosion resistance. Typical applications include precision aerospace bearings and critical components in computer disk drives. The properties of passive films formed on 440C steel were investigated using advanced electrochemical techniques with a view to establishing a method to measure film stability directly in the passivation baths. Electrochemical measurements were sensitive to the passive film properties and were able to quantify the effect of cooling rate on passive film stability. The techniques used included linear polarization, AC impedance, small amplitude cyclic voltammetry, and coulostatic transient measurements. These provided results that exhibited excellent agreement with the AC impedance technique providing the most information about the interfacial reactions. It was found that the full ...

International Nuclear Information System (INIS)

A nitric acid solution containing Cr_2O_7"2"- ion is used for a corrosion test which simulates the condition in a nuclear fuel reprocessing plant. As the effect of Cr content on the corrosion resistance of stainless steel is not yet fully understood in that solution, the effects of Cr content in an alloy and that of Cr_2O_7"2"- ion in nitric acid on the corrosion rate were studied by using electro-chemical measurements. The increase of Cr content reduced the general corrosion rate in nitric acid solution without Cr_2O_7"2"- ion, however it increased that in nitric acid solution containing Cr_2O_7"2"- ion. It is considered that the reversal of the Cr content dependency is due to a rise of the corrosion potential caused by addition of Cr_2O_7"2"- ion to the potential region where a high Cr alloy shows higher anodic dissolution rate than a low Cr content alloy. (author).

International Nuclear Information System (INIS)

Semiconducting properties of passive films formed on AISI 304 stainless steel grade were investigated by capacitances measurements in chloride containing aqueous solutions for different surface finishes: BA (bright annealing in hydrogen containing atmospheres) and 2B (standard annealing in oxidising atmospheres followed by pickling in acid, then water rinsing). Mott-Schottky analysis shows that for high enough electrode potential, and whatever the surface finish, the films behave like n-type semiconductors. 2B passive film appears to be more donor-doped than BA one and the density of donor states increases with chloride concentration. The electron donor levels are assumed to be generated by negatively charged cations vacancies produced by the chloride ions reaction with the outer passive film. This reaction looks easier for 2B than BA condition, which explains why BA resists better than 2B to pit nucleation.

Energy Technology Data Exchange (ETDEWEB)

Stainless steel is pickled in pickling bath with the sulfuric acid and a mixture of hydrofluoric acid and nitric acid. Suitable equipment based on speedy and accurate chemical analysis for actual production lines has not been developed yet. The concentration of sulfuric acid can be analyzed by using the neutralization titration method. As a method of analyzing hydrofluoric acid in the mixed acid, the iron-acetylacetone complex discoloration absorbance method was adopted. For the concentration, of nitric acid, the method of subtracting the concentration of hydrofluoric acid from the total mixed acid amounts obtained by neutralization titration is adopted. Furthermore, the iron-salicylic acid complex absorbance method is adopted as a method of analyzing the iron content. By adopting these methods, the fully automated analyzer is developed. Completing analysis work can be shortened to 40 minutes by automated sampling from the acid pipes. The fully automated acid ...

Energy Technology Data Exchange (ETDEWEB)

The consistency of different instruments and methods for measuring two-dimensional (2D) power spectral density (PSD) distributions are investigated. The instruments are an interferometric microscope, an atomic force microscope (AFM) and the X-ray Reflectivity and Scattering experimental facility, all available at Lawrence Berkeley National Laboratory. The measurements were performed with a gold-coated mirror with a highly polished stainless steel substrate. It was shown that these three techniques provide essentially consistent results. For the stainless steel mirror, an envelope over all measured PSD distributions can be described with an inverse power-law PSD function. It is also shown that the measurements can be corrected for the specific spatial frequency dependent systematic errors of the instruments. The AFM and the X-ray scattering measurements were used to determine the modulation transfer function of the interferometric microscope. ...

Energy Technology Data Exchange (ETDEWEB)

In the framework of the European Fusion Technology Programme ECN participates in a NET task PSM-8 `Coatings and Surface Effects on Stainless Steel 316L`. High emissivity coatings were developed for enhanced heat transfer from graphite tiles to a Stainless Steel First Wall. Four candidate materials, Cr{sub 2}O{sub 3}, Black Cr, Al{sub 2}O{sub 3}/TiO{sub 2} and TiC were tested as candidate high emissivity coatings. These coatings were manufactured by atmospheric and vacuum plasma spraying technique and the Black Chromium coatings were manufactured by a galvanic coating technique. The tests included total emissivity measurements and Low Cycle Fatigue (LCF) experiments. The total emissivity of two TiC coatings at 525 K appeared to be 0.62 and 0.64. The total emissivity of the TiC and 5 wt% TiO{sub 2}/Al{sub 2}O{sub 3} coating was about 0.7. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The carbon transfer has been analyzed in the Alloy 800/sodium/stainless steel system by determining the carbon-uptake of Alloy 800 foils, which were exposed in liquid sodium of known carburizing potential. Under equilibrium conditions between 650 and 550/sup 0/C the measured total carbon concentrations in the Alloy 800 tabs were found to be roughly related to the carbon activities of the sodium environment by the equation already stated for the 18 Cr-8/10 Ni stainless steels, extrapolated to the chemical composition of the Ni-rich austenitic alloy. However the Alloy 800 was not found to undergo any decarburization in low-carbon activity environments. The carbon diffusion kinetics was determined as a function of temperature, it was found to be similar to that reported for the AISI-304 type of steel. The effects of sodium exposure on microstructural and mechanical properties of several Alloy 800 heats were examined at 550/sup 0/C as a function of ...

International Nuclear Information System (INIS)

Modelization of crack propagation and theoretical prediction of rupture are the two main objectives of researchers in stress corrosion cracking. Nevertheless, to reach this aim, the behavior of the passive film which appears spontaneously on the substrate in contact with an environment has to be known. This structural and mechanical characterization is all the more difficult because the number of parameters is important: crystallinity rate, defects concentration, thickness (about a few nanometers), electric field, chemical composition (a lot of oxides are present), peeling layers (atomic structure for example) and some hypothesis can be made about their multi-layer structure, their chemical composition or their epitaxial character... Passive films formed on 316L or 304L stainless steels in different aqueous solutions (in ambient air, in MgCl_2 at 117 deg. C...) have been studied and some important remarks about their mechanical properties are made (brittle ...

International Nuclear Information System (INIS)

A computational procedure is proposed to perform uncertainty analysis for the calculation of the isotopic inventory and radiological quantities obtained as a linear function of it, due to uncertainties in the activation cross sections. The method is applied to determine the uncertainty of the calculated shallow burial index (SBI) from activated type 304 stainless steel (SS) in the most neutron-exposed zone of the HYLIFE-II vessel structure. Results are obtained by means of an element-by-element study. Some other types of steel are also investigated for comparison purposes. The SS304 is confirmed to be the most promising steel option. 16 refs., 2 tabs.

International Nuclear Information System (INIS)

When decontaminated with continuously replenished CAN-DECON reagent in a once-through system, carbon steel contaminated with "6"0Co during exposure to reducing coolant in stainless steel loops loses up to 90 percent of its radioactivity in the first few minutes. Afterwards, the rate of removal falls to much lower values which persist for many hours to the end of the experiment. The effects of flow rate, temperature and reagent concentration on the initial rates of decontamination indicate that mass transfer in the liquid is an important factor in the decontamination. The decontamination factor is influenced by the initial rate.

Energy Technology Data Exchange (ETDEWEB)

A prototype hydride storage bed, using LaNi{sub 4.25}Al{sub 0.75} as the storage material, was fitted with strain gages to measure strains occurring in the stainless steel bed vessel caused by expansion of the storage powder upon uptake of hydrogen. The strain remained low in the bed as hydrogen was added, up to a bed loading of about 0.5 hydrogen to metal atom ratio (H/M). The strain then increased with increasing hydrogen loading ({approximately} 0.8 H/M). Different locations exhibited greatly different levels of maximum strain. In no case was the design stress of the vessel exceeded.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the description of methodological procedure specially developed for manufacturing mini turbines. This procedure is used in the design of a Francis type mini turbine with 12.5 kW. The housing volute and the suction tube of this equipment are manufactured with using composed material based on glass fiber and its distributor system is manufactured with stainless steel and brass. At the end it is presented an estimate cost of design / manufacturing of such equipment and a comparison with other equipment in the market.

Science.gov (United States)

Oak Ridge National Laboratory (ORNL) has for over ten years provided materials testing and failure analysis services to various coal conversion and utilization facilities in the United States. ORNL was involved in these types of activities at all four of the major coal liquefaction pilot plants. This paper presents a summary of activities at Wilsonville over the past two and one-half years. Some details of these activities are discussed below. Failure analysis of elastomers, stainless steels, and alloys is discussed. 6 refs., 9 figs., 13 tabs.

Energy Technology Data Exchange (ETDEWEB)

The failure took place on a welded elbow pipe which exhibited a catastrophic transverse rupture. The failure was located on the welding HAZ region, parallel to the welding path. Branching cracks were detected at the edge of the rupture area. Deposits of corrosion products were also spotted. The optical microscope analysis showed the presence of transgranular failures which were related to the stress corrosion cracking (SCC) and were predominantly caused by the welding residual stress. The significant difference in hardness between the welded area and the pipe confirmed the findings. Moreover, the failure was also caused by the low Mo content in the stainless steel pipe which was detected by means of spark emission spectrometer. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We propose a dissolution-passivation model to account for the electrochemical behavior of Alloy 800 and 316L stainless steel under steam generators operating conditions. This model is similar to the one defined for nickel, considering the known importance of this element on the studied alloys. The comparison of the rates of the elementary steps points out the favorable influence of dissolved oxygen and phosphate ions on the dissolution of Alloy 800, even in the presence of chloride ions. The sensitivity of 316L SS is greater, especially because of the lowest stability of oxide-like intermediate.

International Nuclear Information System (INIS)

Effect of scale on determination of 12Kh18N10T steel tendency to intergranular corrosion (IGC) by rapid electrochemical techniques in solution of 10 % H_2SO_4+0.0025 g/l KCNS was investigated. It is shown that scale presence of steel surface accelerates anode dissolving, activates grain boundaries. All this results to the effect of tendency to IGC in steels, not inclined to it. The scale is not completely removed from the surface, but remains partially along grain boundaries in result of successive pickling of scale and then a surface layer of metal. This also couses the effect of tendency to IGC.

Energy Technology Data Exchange (ETDEWEB)

The buckling test program comprised 37 axially loaded cylinders made of austenitic stainless steels and 6 reference cylinders made of mild steel. The three test parameters were the steel grade, the shell slenderness and the operating temperature. The chosen steel grades are typical for practical applications: AISI 304 (No. 1.4301) as the basic austenitic stainless steel, AISI 316 L (No. 1.4404) as a molybdenum alloyed and AISI 316 Ti (No. 1.4571) as a molybdenum and titanium alloyed austenitic stainless steel. The chosen shell slendernesses are typical for the above-mentioned elastic-plastic region: r/t=50, 150 and 400, approximately corresponding to non-dimensional slenderness parameters {lambda}=0.3, 0.5 and 0.9 respectively. The chosen testing temperatures cover a wide range of applications: T=20 C, 100 C, 250 C and 400 C. The test cylinders were manufactured from 3.0 mm, 1.0 mm and 0.5 mm steel sheets, cold rolled into ...

Energy Technology Data Exchange (ETDEWEB)

Photocurrent measurements for stainless steel type 304 in the as-received condition after dc and AV (alternating voltage) passivation have confirmed that significant changes of the passive film properties occur due to AV passivation. The photocurrents were the highest for the sample treated by the AV passivation process (AVPP). The bandgap energy increased from about 2.8 to about 3.05 eV for this treatment. Very similar results have been obtained for pure chromium, which suggests that the AVPP produces a thicker passive film with a less defective nature due to a partial dehydration of the chromium oxide phase in the film.