Energy Technology Data Exchange (ETDEWEB)

FeAl, which has high oxidation and sulfidation resistance, was shown to be thermodynamically compatible with WC. Calculations indicate that soly. of WC in liq. Fe-40at.%Al at 1450 C is about 2 at.%. Since liquid FeAl wets WC very well, the WC/FeAl system lends itself to liquid-phase sintering, resulting in close to theoretical densities. Almost fully dense cermets with 20.6 wt% FeAl binder were produced. With one-step infiltration, 98% dense cermets with only 7 wt% FeAl binder were fabricated. RT bend strengths and fracture toughness for WC-20.6 wt% FeAl reached 1680 MPa and 22 MPa{center_dot}m{sup 1/2}. Ductile binder fracture was observed on the fracture surfaces. Pores containing oxide inclusions were found, suggesting that improvements in processing are likely to further improve the mechanical properties. Insufficient process control may explain why WC/FeAlNi cermets did not ...

International Nuclear Information System (INIS)

Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of titanium silicide at the boundary of the aluminide coating and substrate, thereby ...

International Nuclear Information System (INIS)

Results of an investigation of the weldability of compact hollow automobile parts are reported. The use of magnetically impelled arc butt (MIAB) welding for a piston rod (OD_22_mm x 2.2_mm thickness), a shock-absorber (OD 40 mm x 2.2 mm) and a torque rod (OD 34 mm x 6 mm) has been investigated. Metallographic examination and comprehensive mechanical testing has been conducted to demonstrate the effectiveness of the method for joining of these types of automobile components

Energy Technology Data Exchange (ETDEWEB)

Attempts to synthesize YPd[sub 2]Si-type representatives LnPd[sub 2]Al were successful only with Ln triple bond Ce, Pr, Nd. This orthorhombic structure (oP16; space group Pnma) is an ordered variant of the Fe[sub 3]C type. Only NdPd[sub 2]Al undergoes magnetic ordering above 2 K. (orig.)

Energy Technology Data Exchange (ETDEWEB)

In this paper coating developments for advanced gas turbine engines (diffusion aluminide coatings, overlay coatings, and ceramic thermal barrier coatings) were desorbed, a selection of current metallic coatings was made and their performance as outlined. Finally coating developments for advanced diesel engines with a view to improved turbocharging or to low heat rejection engines (adiabatic diesel concept) were dealt with. (IHOE).

UK PubMed Central (United Kingdom)

IntroductionMale sexual dysfunction is a common complication of diabetes (DM), but the relative impact of erectile dysfunction (ED), orgasmic dysfunction (OD), and/or...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Currently, high temperature filter systems are in the demonstration phase with the first commercial scale hot filter systems being installed on integrated gasification combined cycle (IGCC) and pressurized fluid bed combustion cycle (PBFC) systems (70 MW). They are dependent on the development of durable and economic high temperature filter systems. These filters are mostly ceramic tubes or candles. Ceramic filter durability has not been high. Failure is usually attributed to mechanical or thermal shock: they can also undergo significant changes due to service conditions. The overall objective of this project is to commercialize weldable, crack resistant filters which will provide several years service in advanced power processes. The specific objectives of this project are to develop corrosion resistant alloys and manufacturing processes to make Iron Aluminide filter media, and to use a ``short term`` exposure apparatus supported by other tests to identify the ...

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Abstract Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X-=-1-m and...

Energy Technology Data Exchange (ETDEWEB)

A new eddy current array probe has been implemented as a straightforward and promising technique for detection of outer diameter (OD) surface-breaking cracks on the extrados of feeder bends. The design is based on previous work performed at AECL, which had demonstrated that eddy current probes with laterally displaced transmit-receive coils can overcome some of the limitations of inspecting ferritic steel components for surface-breaking cracks. The Feeder Integrity Joint Program-CANDU Owners Group Inc. (FIJP-COG) Non-Destructive Evaluation (NDE) Team members commissioned AECL to work in collaboration with the probe manufacturer ZETEC, to develop a field usable eddy current array probe. The objective was to acquire a technique with the following capabilities: fast scanning non-contact inspection technique for surface breaking discontinuities; full inspection of the bend extrados OD surface in a single scan; ability to inspect first and second ...

International Nuclear Information System (INIS)

The Environmental Management System (EMS) is an instrument to manage the interaction between the organization and the environment. The scope od EMS is to reduce the environmental impact and to achieve improvements in overall performances. In particular, the focus point of EMS implementation is the method for identifying and assessing significant environmental aspects. This paper presents a review of methods and techniques existing in this area, and the definition of the state of the art. The results of the literature, regulation and case studies reviews have shown that rigorous, repeatable and transparent methodologies do not exist.

Energy Technology Data Exchange (ETDEWEB)

This paper addresses fuel cycle cost comparisons for a generic 10 MW reactor with HEU aluminide fuel and with LEU oxide and silicide fuels in several fuel element geometries. The intention of this study is to provide a consistent assessment of various design options from a cost point of view. Fuel cycle cost benefits could result if a number of reactors were to utilize fuel elements with the same number or different numbers of the same standard fuel plate. Data are presented to quantify these potential cost benefits. This analysis shows that there are a number of fuel element designs using LEU oxide or silicide fuels that have either the same or lower total fuel cycle costs than the HEU design. Use of these fuels with the uranium densities considered requires that they are successfully demonstrated and licensed.

Energy Technology Data Exchange (ETDEWEB)

This report presents the results of cladding technology development under the Coal-Fired Combined Cycle DOE Project for the period July 1976 through June 1978. Sub-task 3.1, Clad Alloy Development, involved the selection, fabrication and burner rig evaluation of advanced clad alloy compositions diffusion-bonded to IN-738. Testing was conducted for up to 5800 hours at 1600/sup 0/F in a simulated PFB environment. Metallographic evaluation showed Co-base cladding alloys PFB-5PM and PFB-6PM (aluminided) and Fe-base alloy GE-2541 to be the most corrosion resistant. The formability and fabricability of sheet material was significantly improved for these alloys by utilizing powder metallurgy techniques. Sub-task 3.2, Clad Process Development, encompassed processing activities to evaluate sheet alloy formability, bucket surface preparation techniques, platform clad forming, and the activated diffusion bonding (ADB) of corrosion resistant tips to MS5001 buckets. The main ...

Energy Technology Data Exchange (ETDEWEB)

PWR steam generators have suffered from a variety of degradation phenomena. This paper identifies the corrosion-related defects and their probable causes and suggests approaches to correct and prevent corrosive activity. In the attempt to solve the degradation problems, research programs have concentrated on modifying materials, stresses, and the chemical environment in both new and operating steam generators. The following corrosion-related defects have been studied: tube wastage, denting, primary side (ID) intergranular stress corrosion cracking (IGSCC), OD-initiated intergranular attack (IGA), pitting, and corrosion fatigue. Plants affected by wastage have greatly reduced their problem by adopting an all volatile treatment (AVT). In the case of denting, a less aggressive chemical environment is recommended. Primary side IGSCC responds to temperature reduction, stress relief, and material improvements, while flushing and boric acid addition minimizes ...

Energy Technology Data Exchange (ETDEWEB)

A key factor that demands special attention in the pipeline construction is the cold bending process, since 30 to 40% of the pipes use this process in the field. This study aimed to evaluate the X80 cold bending operational parameters, in order make viable the use of this process in the installation of future onshore pipelines. Three 34''OD x 0,750'' pipes were bended. The bending was conducted using a hydraulic equipment with application of equally spaced punches, recording the correspondent angles related to the elastic and plastic deformations in order to assess the spring-back effect and performing dimensional inspection. Samples from pipe and the weld were subjected to mechanical and metallographic tests. It was possible to obtain a 19 deg curve and 27D radius without presenting any evidence of wrinkles, out of roundness or any type of mechanical damage. After analysis, all criteria established from project specifications ...

Energy Technology Data Exchange (ETDEWEB)

The shot peening of the outer surface of Alloy 800 is proposed by the steam generator supplier in order to increase the stress corrosion cracking resistance of the tubes. The benefits and drawbacks of such a treatment are evaluated, focusing on the main concern i.e. a possible enhanced tendency of stress corrosion cracking at the transition of the expanded tube-to-tubesheet joint. Stress corrosion tests as well as residual stresses measurements demonstrate no significant difference between peened and unpeened tubes at that location. The other concerns such as stability of the compressive stresses, increased risk of pitting or intergranular attack and pollution of the secondary circuit by fragmented beads appear the as minor concerns.

International Nuclear Information System (INIS)

The fabrication of the ZT-40 torus, a large complex all-ceramic toroidal plasma containment vessel, is described. Several glass sealants covering the temperature range of 500 to 1300"0C, were developed and used to ''braze'' segments of the torus together, sapphire windows to the torus and the required pump-out and diagnostic parts to the ceramic vacuum vessel. Designs of window seals were developed that allowed sealing of the sapphire windows in a vertical position with minimum sealing glass flow.

Energy Technology Data Exchange (ETDEWEB)

Surface modification of topography and chemistry in order to achieve a specific water contact angle (CA) has been explored by using a novel combinatorial screening platform. The screening arrays consisted of 507 distinct combinations of micro-topographies and chemical compositions. By performing chemical modifications with 1H, 1H, 2H, 2H perfluoroethyltriethoxy-silane (PFS) and n-octadecyltriethoxysilane (ODS) on standard silicon wafers it was possible to include both superhydrophobic and very hydrophilic pad arrays in the same screening platform. Surfaces modified with PFS were more hydrophobic than surfaces modified with ODS, while the unmodified silicon surfaces were hydrophilic. For the PFS modified surfaces the largest CAs were achieved with a small pillar size of X = 1 {mu}m and an intermediate inter-pillar gap size of Y = 4 {mu}m with superhydrophobic CAs over 170 . Surface analysis with X-ray photoelectron spectroscopy (XPS) revealed ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work was the examination of the coarse grain recrystallisation of the {gamma}-free ODS nickel-based alloy PM 1000 depending on the various parameters due to the processing during heat treatment. After isotropic hot compacting (HIP) of the mechanically alloyed powder, one observes a homogeneous sub-microscopic fine grain structure which can coarsen during high temperature heat treatment, due to sufficiently high driving force from the grain boundary energy via abnormal grain growth to 600 times its size. The setting of the elongated high temperature resistant recrystallisation structure is, however, not connected with this. The dependence of the sucess of re-crystallisation on the re-forming parameters (re-forming temperature and degree of re-forming) was shown by a socalled re-forming card. In order to achieve re-crystallisation to a coarse and aligned grain structure, apart from a certain absolute minimum degree of re-forming, the re-forming must ...

British Library Electronic Table of Contents (United Kingdom)

High purity W and W-0.9La2O3 (wt.%) nanopowders were produced by a wet chemical route. The precursor was prepared by the reaction of ammonium paratungstate (APT) with lanthanum salt in aqueous solutions. High resolution electron microscopy investigations revealed that the tungstate particles were coated with oxide precipitates. The precursor powder was reduced to tungsten metal with dispersed lanthanum oxide. Powders were consolidated by spark plasma sintering (SPS) at 1300 and 1400degreeC to suppress grain growth during sintering. The final grain size relates to the SPS conditions, i.e. temperature and heating rate, regardless of the starting powder particle size. Scanning electron microscopy revealed that oxide phases were mainly accumulated at grain boundaries while the tungsten matrix ...

Science.gov (United States)

Spike-timing-dependent plasticity (STDP), a form of Hebbian plasticity, is inherently stabilizing. Whether and how GABAergic inhibition influences STDP is not well understood. Using a model neuron driven by converging inputs modifiable by STDP, we determined that a sufficient level of inhibition was critical to ensure that temporal coherence (correlation among presynaptic spike times) of synaptic inputs, rather than initial strength or number of inputs within a pathway, controlled postsynaptic spike timing. Inhibition exerted this effect by preferentially reducing synaptic efficacy, the ability of inputs to evoke postsynaptic action potentials, of the less coherent inputs. In visual cortical slices, inhibition potently reduced synaptic efficacy at ages during but not before the critical period of ocular dominance (OD) plasticity. Whole-cell recordings revealed that the amplitude of unitary IPSCs from parvalbumin positive (Pv+) interneurons to pyramidal neurons ...

Energy Technology Data Exchange (ETDEWEB)

A procedure for the determination of carboxylic acids (benzoic and C{sub 8}-C{sub 16} aliphatic acids) in oxidised engine oils is described. It is based on a simple and selective derivatisation of the acids with a fluorescent label 9-anthracene-methanol followed by reverse-phase separation on an ODS column with a water-acetonitrile-tetrahydrofuran (20:40:40 by volume) mobile phase and post-column reaction with bis(2,4-dinitrophenyl) oxalate and hydrogen peroxide. The chemiluminiscence emission from the reaction was monitored using a lamina flow-through detector. Analysis of oxidised oils showed that although there was quenching of chemiluminiscence emission by the oil matrix, the acids could be determined over the range 0-0.4% (m/v) in the oil with a detection limit of 0.013% (m/v) (130 pmol on-column with a 20 {mu}l injection) for lauric acid. 8 figs., 2 tabs., 17 refs.

International Nuclear Information System (INIS)

Safety studies related to the disposal of low- and intermediate waste indicate that the long term risk is determined by the presence of long-lived nuclides such as "1"4C, "5"9Ni, "6"3Ni, "9"9Tc, "1"2"9I and the transuranium elements. As most of these nuclides are difficult to measure, the correlation between these critical nuclides and some other easily measurable key nuclides such as "6"0Co and "1"3"7Cs has been investigated for typical waste streams of Paks Nuclear Power Plant (Hungary) and scaling factors have been proposed. An automated gamma-scanning monitor has been purchased and calibrated to determine the gamma-emitting radionuclides. Radiochemical methods have been developed to determine significant difficult-to-measure radionuclides. The radionuclides of interest have been "3H, "1"4C, "9"0Sr, "5"5Fe, "5"9Ni, "9"9Tc, "1"2"9I and TRUs. The measurements taken so far have revealed brand new information and data on radiological composition of waste of WWER-type reactors. The ...

Energy Technology Data Exchange (ETDEWEB)

A prospective study was performed on 50 patients suffering from osteochondritis dissecans of the knee and ankle to define criteria for stability and fixation of osteochondral lesions. Morphological parameters in MRI (size, fragmentation, cartilage, interface) and conventional radiology (separation, fragmentation) were registered and compared with arthroscopical staging. MRI staging based on different types of interfaces was demonstrated on T{sub 1}- and T{sub 2}-weighted images. MRI could correctly predict a Grade 1 lesion in 50%, a Grade 2 lesion in 90%, a Grade 3 lesion on 0%, and a Grade 4 lesion in 79%. Stable lesions were differentiated from unstable lesions in 90%. Radiographic findings corresponded with arthroscopic staging in only 56% of the cases because fibrotic connection may guarantee stability in case of bony separation. (orig./MG) [Deutsch] In einer prospektiven Studie an 50 Patienten mit einer Osteochondrosis dissecans (OD) des Knie- und ...

Science.gov (United States)

A liquid chromatography tandem mass spectrometry (LC-MS/MS) method was developed for the simultaneous determination of the 10 major components of Da-Cheng-Qi decoction (rhein, emodin, aloe-emodin, chrysophanol, rheochrysidin, naringin, naringenin, hesperidin, magnolol and honokiol) in dog plasma. Plasma samples were spiked with internal standard (ibuprofen), acidified with HCl and extracted twice by liquid-liquid extraction using ethyl acetate. Separation was performed on a YMC-Pack ODS-A C(18) column (5 microm, 150 mm x 4.6 mm) and a C(18) guard column (5 microm, 4.0 mm x 2.0 mm) with methanol-water (92:8, v/v) at a flow rate of 0.3 mL/min. The LC/MS system was operated under the multiple reaction monitoring mode using electrospray ionization in the negative ion mode. All analytes showed good linearity over a wide concentration range (r>0.99). The linear range of the calibration curves was 5000-19.53 ng/mL for rhein; 400-3.13 ng/mL for emodin; 800-3.13 ng/mL ...

Energy Technology Data Exchange (ETDEWEB)

The secondary side corrosion of steam generator tubes is the main degradation of components in operating power plants, strongly impacted by chemistry. This is why EDF has largely studied the chemical parameters in its 56 PWRs which might influence corrosion development. The results of 168 hideout returns of chemical species performed on the French plants allowed to draw conclusions on where chemical species are likely to concentrate in steam generators and on the influence of several contaminants on corrosion processes: sodium, chloride, phosphate, organic compounds, etc... Based on laboratory studies and plants feedback, new chemistry specifications were established and are now applied to EDF units to minimize corrosion and operating costs and to provide a good availability while maintaining an excellent safety. Boric acid is added in the secondary water of the 10 oldest units with Inconel 600 MA tubing, highly sensitive to intergranular stress corrosion cracking. Implementation of ...

Energy Technology Data Exchange (ETDEWEB)

The preparation and performance of membranes for application to hydrogen separation from coal-derived gas is described. The membrane material investigated was dense amorphous silica deposited on a suitable support by chemical vapor deposition (CVD). Two types of support materials were pursued. One type consisted of a two-layer composite, zeolite silicalite/{alpha}-Al{sub 2}O{sub 3}, in the form of tubes approximately 0.7 cm in diameter. The other type was porous glass tubes of diameter below 0.2 cm. The first type of support was prepared starting from {alpha}-Al{sub 2}O{sub 3} tubes of 1{micro}m mean pore diameter and growing by hydrothermal reaction a zeolite silicalite layer inside the pores of the alumina at the OD side. After calcination to remove the organic template used in the hydrothermal reaction, CVD was carried out to deposit the final silica layer. CVD was carried out by alternating exposure of the surface with silicon tetrachloride and water vapor. SEM ...

Energy Technology Data Exchange (ETDEWEB)

In this thesis, increased hemicellulose retention during kraft pulping has been studied. The work has been divided into three parts: i) Development of an accessible and reliable method for determination of carbohydrate composition of kraft pulps ii) Investigation of the composition and molecular mass distributions of the carbohydrates in kraft pulps with increased hemicellulose content iii) Investigation of the effect of increased hemicellulose content on the sheet properties of kraft pulps with increased hemicellulose content. A method for carbohydrate determination was developed. In this method, enzymes are used to hydrolyse the pulp into monosaccharides. A relatively mild acid hydrolysis is performed prior to detection on an HPLC with an RI-detector. The pulp is not derivatized and no pre-treatment (mechanical or chemical) is needed to determine the carbohydrate composition using the method developed here. Peak deconvolution software is used to improve the accuracy. Polysulphide and ...