Science.gov (United States)

... 2009. Copyright belongs to the Marine Technology Society., The original document contains color images. 14. ABSTRACT ...

Energy Technology Data Exchange (ETDEWEB)

A new class of one-dimensional active acoustic metamaterials (AAMMs) with programmable effective densities is presented. The proposed AAMM is capable of producing densities that are orders of magnitudes lower or higher than the ambient fluid. Such characteristics are achieved by using an array of fluid cavities separated by piezoelectric diaphragms that are controlled to generate constant densities over wide frequency bands. The piezodiaphragms are augmented with passive electrical components to broaden the operating frequency bandwidth and enable densities higher than the fluid medium to be generated. The use of these components is shown to be essential to maintain the closed-loop compliance of the piezodiaphragm away from the zone of elastic instabilities. The values of the passive components are selected on a rational basis in order to ensure a balance between the frequency bandwidth and control voltage. With this unique ...

Energy Technology Data Exchange (ETDEWEB)

In this work the authors study the stabilization point of a lifted, reacting jet of nitrogen diluted methane in co-flowing air. The jet flow is acoustically forced so as to organize the large scale vortical structures. The validation of the numerical results is possible through a concurrent experimental investigation of a similar planar jet. The use of an acoustically forced planar jet allows for significant savings by the restriction of the computation to two dimensions; the model is otherwise applicable in three dimensions. The authors based their study on the following parameters, which are derived from the experimental setup: a jet width of 1.16 cm, a mean jet velocity of 0.8 m/s, and a coflow velocity of 0.1 m/s. The acoustical forcing is studied at frequencies of 7.5 MHz and 90 MHz, which have been established experimentally as being characteristic of two broad behavioral modes. The authors restrict themselves to five ...

Science.gov (United States)

This site explains how temperature, pressure, and salinity work together to determine the density of ocean water. The three density layers of the ocean are described by means of text description and a graphic illustration.

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

We present a comparative study on the acoustic tunneling through artificial periodical composites, from phononic crystals to acoustic metamaterials. We find that the features of the acoustic tunneling are closely related with the origins of band gaps. In particular, the band gap associated with the negative effective material parameter in the metamaterial results in a better analog of the tunneling effect to the quantum system.

UK PubMed Central (United Kingdom)

Acoustic lenses are employed in a variety of applications, from biomedical imaging and surgery to defense systems and damage detection in materials. Focused acoustic signals, for example, enable ultrasonic...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A shear acoustic transducer-lens system in which a shear polarized piezoelectric material excites shear polarized waves at one end of a buffer rod having a lens at the other end which excites longitudinal waves in a coupling medium by mode conversion at selected locations on the lens.

Energy Technology Data Exchange (ETDEWEB)

The mission of the Emerging Technologies thrust area at Lawrence Livermore National Laboratory is to help individuals establish technology areas that have national and commercial impact, and are outside the scope of the existing thrust areas. We continue to encourage innovative ideas that bring quality results to existing programs. We also take as our mission the encouragement of investment in new technology areas that are important to the economic competitiveness of this nation. In fiscal year 1992, we have focused on nine projects, summarized in this report: (1) Tire, Accident, Handling, and Roadway Safety; (2) EXTRANSYT: An Expert System for Advanced Traffic Management; (3) Odin: A High-Power, Underwater, Acoustic Transmitter for Surveillance Applications; (4) Passive Seismic Reservoir Monitoring: Signal Processing Innovations; (5) Paste Extrudable Explosive Aft Charge for Multi-Stage Munitions; (6) A Continuum Model for Reinforced Concrete ...

Energy Technology Data Exchange (ETDEWEB)

With an objective to detect gas leaking from an underground gas pipeline, discussions have been given on a method which utilizes acoustic characteristics of leakage. On leaking sound generated from damaged portions, the form of damaging was hypothesized as pinholes, and spectra of leaking sounds from holes with different diameters were measured. The dominant frequency decreases as the hole diameter increases, while it is in a region of relatively high frequency of 1 kHz or higher. However, detection from the ground surface was impossible when cover soil has thickness from 0.5 to 1.5 m. In an experiment to measure leaking sound inside the pipe, pressure in the pipe was adjusted to 0.02 atm which is a standard pressure for a low-pressure pipe, and the sound was measured when the hole diameters were varied. In any of the results obtained by varying the hole diameter, spectra having the dominant frequency in the region of 1 kHz or higher were measured. In addition, it ...

Science.gov (United States)

The satellite ocean color data record spans multiple decades and, like most long-term satellite

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

This work proposes an acoustic structure feasible to engineer that accomplishes the requirements of acoustic cloaking design recently introduced by Cummer and Schurig (2007 New J. Phys. 9 45). The structure, which consists of a multilayered composite made of two types of isotropic acoustic metamaterials, exactly matches the conditions for the acoustic cloaking. It is also shown that the isotropic metamaterials needed can be made of sonic crystals containing two types of material cylinders, whose elastic parameters should be properly chosen in order to satisfy (in the homogenization limit) the acoustic properties under request. In contrast to electromagnetic cloaking, the structure here proposed verifies the acoustic cloaking in a wide range of wavelengths; its performance is guaranteed for any wavelength above a certain cutoff defined by the homogenization limit ...

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) is to evaluate the radiological conditions at former MED-US AEC sites. Purpose of the Ocean FUSRAP program is to assess the feasibility of ocean disposal of FUSRAP waste which contains trace natural radioactive materials. This paper presents soil characterization information on the Middlesex, NJ, Sampling Plant site, and reports preliminary ocean dispersion calculations. (DLC)

Energy Technology Data Exchange (ETDEWEB)

A series of speeches is presented which cover political aspects of ocean energy, legislation, the status of the DOE Ocean Energy Program, the Maritime Administration OTEC Support Program. Six workshop reports are given covering ocean energy technology and systems concepts, power systems concepts, environmental developments, energy transfer and utilization, construction and test capabilities, and industry development. (LEW)

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP waste which contains traces of natural radioactive materials. The initial planning has focused on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of material. The Belgian Congo uranium ore and other uranium ores used by the United States were handled at the sampling plant site and have since been removed.

UK PubMed Central (United Kingdom)

Measurements are reported of ultrasonic acoustic emissions (AEs) measured from sapwood samples of Thuja occidentalis L. and Tsuga canadensis (L.) Carr. during air dehydration....Full Text Available

International Nuclear Information System (INIS)

Russian 2010 p. 382 Ukraine Yuferov, VB Ozerov, AN Ponomarev,

CERN Document Server

We fabricated a double negative acoustic metamaterial which consisted of Helmholtz resonators and membranes. Experimental data on the transmission and dispersion relation are presented. The system exhibits three frequencies where the acoustic state makes sharp transitions from density negative ({\\rho} -NG) to double negative (DNG), modulus negative (B-NG), and double positive (DPS) in sequence with the frequency. We observed a wide range of negative refractive index from -0.06 to -3.7 relative to air, which will allow for new acoustic transformation techniques.

CERN Document Server

We investigate theoretically subwavelength imaging by acoustic metamaterial slabs immersed in the liquid matrix. A near-field subwavelength image formed by evanescent waves is achieved by a designed metamaterial slab with negative mass density and positive modulus. A subwavelength real image is achieved by a designed metamaterial slab with simultaneously negative mass density and modulus. These results are expected to shed some lights on designing novel devices of acoustic metamaterials.

Science.gov (United States)

period T. Also shown is the returned chirp from a specular reflector at ...... algorithms is a Brown (1977) model of the return waveform, which assumes a ...... Townsend, W.F., 1980: An initial assessment of the performance achieved by ...

Energy Technology Data Exchange (ETDEWEB)

The Subseabed Disposal Program has recently completed a 30-day, 0.286-scale laboratory simulation of an In Situ Heat Transfer Experiment (ISHTE), scheduled for eventual deployment in the deep ocean 600 nautical miles north of Hawaii. 10 figures.

Energy Technology Data Exchange (ETDEWEB)

Only half of the carbon dioxide produced by burning fossil fuels stays in the atmosphere. It is thought that the oceans absorb the rest. To understand the world's climate it is necessary to know how the atmosphere, ocean and biosphere interact.

British Library Electronic Table of Contents (United Kingdom)

We analyse numerically the acoustic stop band properties of an array of orthotropic coated cylinders whose elastic parameters are deduced from a geometric transform [H. Chen, C.T. Chan, Acoustic cloaking in three dimensions using acoustic metamaterials, Appl. Phys. Lett. 91 (2007) 183518]. We find that whereas a single coated inclusion is acoustically neutral at any frequency, an array of them might display some stop bands. More precisely, an array of freely vibrating coated voids is always neutral, whereas an array of clamped coated inclusions might display a zero frequency stop band. Interestingly, an array of radially symmetric coated inclusions behaves as local Helmholtz resonators, for which the eigenfield within each cloak is obtained in closed form, leading to a frequency estimate a...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... 2004, Underwater Gliders for Ocean Research. Journal of the Marine Technology Society. Fiorelli, E., NE Leonard, P. Bhatta ...

Wastenet

... Studies People Projects Opportunities Framework Critical Sectors Development Goals Geographic Region Geographic Scale Research Themes Printer-Friendly Center for Ocean Solutions Early Career Fellowship Program Location: Stanford, California Source: The Center for Ocean Solutions (“Ocean Solutions”) seeks one or more recent graduates who have received a JD, MBA or PhD in the natural, physical or social sciences in the last five years, and who ...

Energy Technology Data Exchange (ETDEWEB)

The structure and composition of the passive films formed on 304 stainless steel in deaerated IN H{sub 2}SO{sub 4} were studied by RHEED, XPS and AES. The stability of the passive films as a function of passivation potential and passivation time were investigated. The role of bound water in affecting the stability of the passive films is discussed. 7 refs., 3 figs.

Energy Technology Data Exchange (ETDEWEB)

Conference paper regarding research in the use of freeze prevention for passive solar domestic water heating systems.

Science.gov (United States)

Al-Balushi KR, Samanta B. Gear fault diagnosis using energy-based features of acoustic emission signals. Proc. IMechE, Part I: ...

Energy Technology Data Exchange (ETDEWEB)

A method and device have been provided for distinguishing Africanized honeybees from European honeybees. The method is based on the discovery of a distinct difference in the acoustical signatures of these two species of honeybees in flight. The European honeybee signature has a fundamental power peak in the 210 to 240 Hz range while the Africanized honeybee signature has a fundamental power peak in the 260 to 290 Hz range. The acoustic signal produced by honeybees is analyzed by means of a detecting device to quickly determine the honeybee species through the detection of the presence of frequencies in one of these distinct ranges. The device includes a microphone for acoustical signal detection which feeds the detected signal into a frequency analyzer which is designed to detect the presence of either of the known fundamental wingbeat frequencies unique to the acoustical signatures of these species as ...

Energy Technology Data Exchange (ETDEWEB)

An electronically controllable apparatus is described which modulates a continuous wave laser beam so as to produce an output beam consisting of coherent ''pulses'' that are electronically controllable as to both pulse repetition rate and pulse width. The apparatus includes two acoustic devices positioned so that the laser beam passes through them in sequence, and apparatus or for passing sound waves through the devices to frequency shift the laser radiation as well as to diffract it. Each acoustic device such as generates sound waves containing a group of frequencies which result in spaced pulses. The spreading of a laser beam at which emanates from the first acoustic device is countered by the second acoustic device to produce a collimated, coherently pulsed, laser beam.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Research highlights: {yields} The polarization curve of 316L SS possesses five turning potentials in passive region. {yields} Films formed at turning potentials perform different electrochemical and semiconductor properties. {yields} Dissolutions and regenerations of passive film at turning potentials are obtained by AAS and XPS. {yields} Turning potentials appearing in passive region are ascribed to the changes of the compositions of the passive films. - Abstract: The passivity of 316L stainless steel in borate buffer solution has been investigated by Mott-Schottky, atomic absorption spectrometry (AAS) and X-ray photoelectron spectroscopy (XPS). The results indicate that the polarization curve in the passive region possesses several turning potentials (0 V{sub SCE}, 0.2 V{sub SCE}, 0.4 V{sub SCE}, 0.6 V{sub SCE} and 0.85 V{sub SCE}). The ...

Energy Technology Data Exchange (ETDEWEB)

Separate abstracts were prepared for 62 papers in this volume of conference proceedings. Two other papers were previously abstracted for EDB. (LEW)

Environmental Research Database

Objectives(i) Investigate the correlation between Antarctic sea-ice and equatorial sea-surface temperature anomalies in a realistically forced ocean model simulation of the last 50 years. (ii) Determine whether and how the enormous seasonal change in distribution of sea-ice modifies the seasonal cycle at the Equator. (iii) Determine the detailed pathways of wave propagation both in a historically-forced simulation and in response to realistic perturbations. (iv) Quantify the amplitude of the response i [continued...]DescriptionIt is well known that the equatorial ocean-atmosphere system plays a key role in global climate events such as the El Nino-Southern Oscillation (ENSO) phenomenon. There is now compelling evidence that changes in the Antarctic can strongly and quickly affect the equatorial ocean and the ENSO cycle. Observations demonstrate statistically significant correlations (teleconnections) between the Antarctic ...

Science.gov (United States)

A Self-Powered Underwater Robot for Ocean Exploration and Beyond ... first unmanned underwater vehicle (UUV) that is completely powered by renewable energy . ...

Energy Technology Data Exchange (ETDEWEB)

A strategy for the management of the disposal of low-level radioactive wastes into coastal zones and ocean waters has developed over the past three decades. While there has been a substantial increase in the number of international and required agreements there has also been a concomitant improvement in our understanding of the ocean and the processes at work within it. This has allowed more rigorous and reliable assessments to be made of the radiological consequences. With the continued development of basic guidelines of radiological protection by the International Commission on Radiological Protection (ICRP) methodologies have been formulated to derive the fundamental scientific requirement - the relationship between disposal or release rate to the ocean and the resultant radiation dose to exposed human populations.

International Nuclear Information System (INIS)

Present and potential future changes to the global environment have important implications for marine pollution and for the air-sea exchange of both anthropogenic and natural substances. This report addresses three issues related to the potential impact of global change on the air-sea exchange of chemicals: Global change and the air-sea transfer of the nutrients nitrogen and iron. Global change and the air-sea exchange of gases. Oceanic responses to radiative and oxidative changes in the atmosphere. The deposition of atmospheric anthropogenic nitrogen has probably increased biological productivity in coastal regions along many continental margins. Atmospheric deposition of new nitrogen may also have increased productivity somewhat in mid-ocean regions. The projected future increases of nitrogen oxide emissions from Asia, Africa and South America will provide significant increases in the rate of deposition of oxidized nitrogen to the central ...

Science.gov (United States)

... Distribution Unlimited: Approved for "i3a. ... 'he tide changes were obtained using the standard NOAA National Ocean Survey tide tables. ...

Science.gov (United States)

... Characterizing the Relative Contributions of Large Vessels to Total Ocean Noise Fields: A Case Study Using the Gerry E. ... ...

Energy Technology Data Exchange (ETDEWEB)

Cheap air conditioning from oceanic temperature differences is a possible new competitor for coal in coastal regions. Coal suppliers planning expansion in growing economies need to be aware of the possibilities and limitations of this new competitor. Ocean thermal energy conversion (OTEC) used to be uneconomic but the National Energy Laboratory of Hawaii (NELH) has developed a very economic method of utilising the temperature difference between warm ocean surface and cold deep ocean to generate energy for air conditioning. The article outlines the process and mentions demonstrations of OTEC technology to produce electricity and air conditioning at a site in Kailua-Kona, Hawaii. Indonesia and India have viable sites for OTEC installations, and NELH is working with Madras State on a project to construct a commercial OTEC plant in India. 2 photos.

International Nuclear Information System (INIS)

It is maintained that special features of FFTF make it an ideal system to test sodium boiling detection techniques by acoustic/neutronic methods and to test the response of acoustic/neutronic sensors to vibrations. It is shown that accumulated research results indicate that such tests in FFTF are feasible, predictable, promising and safe. (author).

Energy Technology Data Exchange (ETDEWEB)

Mott-Schottky (M-S) analysis is an effective approach to investigate the electronic property of passive films of metals, and it is well suitable for the passive film with single space charge capacitance. But there is no proper method to analyze the C{sub sc}{sup -2} vs. V{sub m} plots of passive films with several space charge capacitances in series connection, such as bipolar passive films. In this paper, the relationship between the space charge capacitance of the bipolar passive film and the applied potential was deduced and the features of corresponding plots were given out simultaneously. Accordingly, a non-linear fitting method was presented to analyze the C{sub sc}{sup -2} vs. V{sub m} plots of bipolar passive films. Then the method was used to study the semiconductor characteristics of bipolar passive films formed on the surface of ...

CERN Document Server

Kelvin-Helmholtz instability of short gravity waves is examined in order to explain the recent findings of the decrease in momentum transfer from hurricane winds to sea waves. A three-fluid configuration of a foam layer between the atmosphere and the ocean is suggested to provide signifficant stabilization of the system and shifting the marginal critical wavelength to the shortwave part of the spectrum. It is conjectured that such stabilization leads to the observed drag reduction. The high contrasts in three fluid densities provide a universal mechanism for stabilizing surface perturbations.

Energy Technology Data Exchange (ETDEWEB)

Separate abstracts were prepared for 20 papers in this conference report and includes all papers in the ''engineering'' section (program E). Ocean thermal energy conversion (OTEC), moorings, cables, corrosion protection, corrosion testing, coatings, offshore platforms, pipelines, OTEC models and pilot plants, and energy transfer are topics discussed.

Wastenet

...ENSO Applications Center (PEAC) Institutional Affiliation: PEAC's core members are The National Oceanic and Atmospheric Administration - Office of Global Programs (NOAA/OGP) The NOAA National Weather Service - Pacific Region (NWS-PR), The University of Hawaii - School of Ocean and Earth Science and Technology UH/SOEST, The University of Guam - Water and Energy Research Institute (UOG/WERI), and a regional association of the USAPI Governments, the Pacific Basin ...

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy 690 in different pH solutions at high temperatures were studied by potentiodynamic polarization, Auger electron spectroscopy, thermodynamic diagrams and the Mott-Schottky relation. The chemical compositions and electronic structures of the passive films were found to be strongly pH-dependent. In alkaline solutions, a secondary passivation was clearly observed on potentiodynamic polarization curves. The passive films were a mixture of Cr{sub 2}O{sub 3} and FeCr{sub 2}O{sub 4} below the flat band potential of nickel oxide and were NiFe{sub 2}O{sub 4} above this potential. Electronic structure models, describing the electrochemical properties of the passive films, are proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

The oceanic phytoplancton productivity may essentially influence the total rate of the atmospheric CO{sub 2} absorption by the ocean - that is, a considerable amount of CO{sub 2} will be taken-up in the 50 micrometers thick layer near the air-sea interface. Even if phytoplancton production constitutes only 5% of the total oceanic biota production, this will increase the rate of CO{sub 2} absorption more than twice compared with the present estimates. The reason is that metabolic activity of phytoplancton leads to the emergence in a thin scin (50 micrometers, the average size of phytoplancton cells) layer near the water surface of an additional minimum in the CO{sub 2} partial pressure profile and of an additional maximum of {Delta} {sup 13}C in the same area. These two extremums cannot be detected if the corresponding characteristics are averaged over any microscopic area in the well mixing layer that is more than 1 meter ...

International Nuclear Information System (INIS)

Passivity of aluminum (Al) alloy 3003 in air and in aqueous solutions without and with chloride ions was characterized by electrochemical measurements, including cyclic polarization, electrochemical impedance spectroscopy (EIS), localized EIS and potential of zero charge, Mott-Schottky analysis and secondary ion mass spectroscopy (SIMS) technique. Stability, pitting susceptibility and repassivation ability of Al alloy 3003 under various film-forming conditions were determined. Results demonstrated that passive films formed on 3003 Al alloy in air and in Na2SO4 solution without and with NaCl addition show an n-type semiconductor in nature. The passive film formed in chloride-free solution is most stable, and that formed in chloride-containing solution is most unstable, with the film formed in air in between. Pitting of Al alloy 3003 passivated both in air and in aqueous solutions is inevitable in the ...

Energy Technology Data Exchange (ETDEWEB)

By using a two-step homogenization approach, we derive analytical formulas of effective mass density {rho}{sub e} and effective bulk modulus B{sub e} for two- and three-dimensional acoustic metamaterials of Helmholtz resonators (HRs) in fluid. A negative B{sub e} is found at certain frequencies due to the monopolar resonance, leading to a low-frequency acoustic band gap. A unified picture is presented for metamaterials of HRs and three-component metamaterials of negative {rho}{sub e}. Our work supports recent observations in a one-dimensional array of HRs [N. Fang et al., Nat. Mater. 5, 452 (2006)] and presents important high-dimensional extensions for exploring more fascinating phenomena.

Energy Technology Data Exchange (ETDEWEB)

It has been shown that two-dimensional arrays of rigid or fluidlike cylinders in a fluid or a gas define, in the limit of large wavelengths, a class of acoustic metamaterials whose effective parameters (sound velocity and density) can be tailored up to a certain limit. This work goes a step further by considering arrays of solid cylinders in which the elastic properties of cylinders are taken into account. We have also treated mixtures of two different elastic cylinders. It is shown that both effects broaden the range of acoustic parameters available for designing metamaterials. For example, it is predicted that metamaterials with perfect matching of impedance with air are now possible by using aerogel and rigid cylinders equally distributed in a square lattice. As a potential application of the proposed metamaterial, we present a gradient index lens for airborne sound (i.e. a sonic Wood lens) whose functionality is demonstrated by multiple ...

Energy Technology Data Exchange (ETDEWEB)

Semiconductor properties of passive films formed on the Fe-18Cr alloy in a borate buffer solution (pH = 8.4) and 0.1 M H{sub 2}SO{sub 4} solution were examined using a photoelectrochemical spectroscopy and an electrochemical impedance spectroscopy. Photo current reveals two photo action spectra that derived from outer hydroxide and inner oxide layers. A typical n-type semiconductor behaviour is observed by both photo current and impedance for the passive films formed in the borate buffer solution. On the other hand, a negative photo current generated, the absolute value of which decreased as applied potential increased in the sulfuric acid solution. This indicates that the passive film behaves as a p-type semiconductor. However, Mott-Schottky plot revealed the typical n-type semiconductor property. It is concluded that the passive film on the Fe-18Cr alloy formed in the borate buffer solution is ...

UK PubMed Central (United Kingdom)

Excised sheets of canine myocardium were subjected to cyclic loading and unloading in the predominant fibre and cross-fibre directions to determine passive mechanical properties. Myocardium under biaxial...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Conference paper regarding research in freeze-protection methods that could extend market acceptance for passive solar domestic water heating systems in more northern climates if the U.S.

International Nuclear Information System (INIS)

The effects of #alpha# particle irradiation on a passive film formed on a 304 type stainless steel are studied in situ. The experimental arrangement minimizes the radiolysis effects due to the electrolyte. Under irradiation, a modification of the electronic structure of the oxide layers is revealed by photo-electrochemistry and impedance measurements. The influence of irradiation on the corrosion resistance of the passive film is investigated. Comparing the rest potential and the breakdown potential respectively under and without irradiation, a drop in the passivity range under irradiation is shown. this is interpreted as a decrease in the corrosion resistance. (author).

International Nuclear Information System (INIS)

... Sciences, Research Center for Radiation Protection, Chiba (Japan) Hafez,

Science.gov (United States)

The summertime tropical cyclogenesis rate per unit area in the eastern Pacific ocean is arguably higher than in any other location in the world. Many if not most of these cyclones form from African easterly waves which cross Central America into the Pacific. Of order 25% of these waves intensify into cyclones. A significant fraction of east Pacific tropical cyclones undergoes landfall on the Mexican coast. Those which do not, generally dissipate over cold ocean waters north of the east Pacific intertropical convergence zone, often not far from land. The layer of warm ocean water which supports the development of east Pacific cyclones is unusually shallow and is structured by anticyclonic vortices which form by various processes and propagate slowly to the west. These vortices locally deepen the oceanic mixed layer and support stronger convection than their surroundings, possibly promoting ...

International Nuclear Information System (INIS)

The Formerly Utilized Sites Remedial Action Program (FUSRAP) of the Department of Energy is designed to identify and evaluate the radiological conditions at sites formerly used by the Corps of Engineers Manhattan Engineer District and the US Atomic Energy Commission. Where required, remedial action will be instituted to remove potential restrictions on the use of the sites due to residual low-level radioactive contamination. A total of 31 sites that may require remedial action has been identified. The purpose of the Ocean FUSRAP Program, which began in March 1981, is to assess the technical, environmental, and institutional feasibility of disposing, in the ocean and on the ocean floor, of FUSRAP soil and rubble which contains traces of natural radioactive materials. The initial focus has been on the Middlesex, New Jersey, Sampling Plant site and surrounding properties, which contain on the order of 100,000 metric tons of ...

Energy Technology Data Exchange (ETDEWEB)

Previous studies have found that classrooms are often inadequately ventilated, with the resultant increased risk of negative impacts on the pupils. This paper describes a series of field measurements that investigated the indoor air quality, thermal comfort and acoustic performance of nine recently built secondary schools in England. The most significant conclusion is that the complex interaction between ventilation, thermal comfort and acoustics presents considerable challenges for designers. The study showed that while the acoustic standards are demanding it was possible to achieve natural ventilation designs that met the criteria for indoor ambient noise levels when external noise levels were not excessive. Most classrooms in the sample met the requirement of limiting the daily average CO{sub 2} concentration to below 1500 ppm but just a few met the need to readily provide 8 l/s per person of fresh air under the easy ...

International Nuclear Information System (INIS)

Superconductivity in A-15 compounds is examined in terms of electron pairing induced by exchange of acoustic plasmons. The electronic band structure of Nb_3Sn, V_3Si, and similar materials favor transition temperatures of Tsub(c)approximately20 K. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Papers are presented in the areas of: Medical Technologies; Non-Destructive Evaluation; Applications of Signal/Image Processing; Laser Guide Star and Adaptive Optics; Computational Electromagnetic, Acoustics and Optics; Micro-Impulse Radar Processing; Optical Applications; TANGO Space Shuttle.

Science.gov (United States)

The effect of spatial auditory information on a listener's ability to detect, identify, and monitor multiple simultaneous speech signals was evaluated using virtual audio technology. Factorial combinations of three variables - the number of localized spee...

Energy Technology Data Exchange (ETDEWEB)

Samples of fat coal-E, its roof sandstone-A and blind coal-W from two coal mines in Hebei Province of China were brought to the laboratory to study the features of infrared thermal images and radiation temperature in the course of uni-axial load and uni-axial cycle load. To check the results of infrared remote sensing detection, two other methods, acoustic emission detection and electrical resistance detection were also used. The AGA-782 thermalvision detected change of the temperature field of the samples` surfaces. The study showed that: (1) coal rocks and sandstone in the course of loading have three types of infrared thermal image features and three types of infrared radiation temperature features; (2) infrared detection is comparable with acoustic emission detection and electrical resistance detection. Generally, the infrared forewarning of coal rocks` failure comes later than that of acoustic and electrical ...

UK PubMed Central (United Kingdom)

Noise pollution from human traffic networks and industrial activity impacts vast areas of our planet. While anthropogenic noise effects on animal communication are well documented, we have very limited...Full Text Available

UK PubMed Central (United Kingdom)

Vestibular schwannomas, also called acoustic neuromas, are benign tumors of the vestibulocochlear nerve. Patients with these tumours almost always present with signs of hearing loss, and many also experience...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Mass density of a composite is generally taken as the volume-averaged value of components' densities. Moreover, the same volume-averaged mass density is usually used to calculate the wave speed in the long-wavelength limit, i.e., where the wavelength is much larger than the size of the inhomogeneities. In this paper, we show via rigorous derivation that the dynamic mass density used in the calculation of (long-wavelength) wave speed can differ significantly from the static volume-averaged value. This recognition is shown to yield an excellent account of some recent experimental data, as well as to make possible the realization of acoustic metamaterials. Physical reason for the difference between two mass densities is attributed to the relative motion between the components. That is, the implicit assumption-that all components in a composite must move uniformly in the long-wavelength limit-can be violated in the limit of large acoustic ...

Energy Technology Data Exchange (ETDEWEB)

Ultrasonic enhancement of heat transfer on a narrow surface was measured by changing the width of the surface from 8 to 0.1 mm. Ultrasonic power of 600 W with a frequency of 40 kHz was used. Heat transfer on the narrow surface without ultrasonic vibration was correlated by the experimental equation for a thin wire. The cavitation intensity was measured by the cavitation erosion loss of an aluminum foil of 15 [mu]m thickness. The effects of acoustic streaming and cavitation were separated by this measurement. Heat transfer by acoustic streaming was predicted through forced convection. Enhancement by cavitation was explained by the turbulence thermal conductivity of the microjets.

Science.gov (United States)

An improved acousto-optic laser Q-switch uses a chirped fm pulse in the acousto-optic cell to diffract and focus the input beam into a resonating high-Q mode. When the rf acoustic pulse is not wholly within the cell, the beam is diverted to the output. A reflective surface is placed on the cell to yield only one output beam and to yield a retroflective beam back into the cavity for a high Q condition whenever a correctly generated chirp acoustic wave is in the proper postion within the cell.

International Nuclear Information System (INIS)

To get a better understanding of the condensation oscillation and chugging process during blowdown of a BWR after a LOCA a large number of large scale pressure suppression experiments have been performed in several countries. ECN has performed a detailed analysis of the results of one of these experiments, e.g. the DAS M10 experiment of GKSS. This analysis includes the following aspects: Power Spectral Density (PSD) analysis of the data, analysis of the acoustic frequencies of the downcomers and an analysis of the eigenfrequencies of the downcomers. The results of these analyses and an evaluation are given in this paper. It is shown that all dominant frequencies in the experimental results can be correlated with the vent-acoustic or eigenfrequencies. (orig.).

Energy Technology Data Exchange (ETDEWEB)

This book, an updated version of the 1985 edition, contains thirteen chapters, beginning with a preface which provides the objective of the book. The primary objective is to offer a comprehensive survey of the biological, hydrological, mathematical, and biochemical aspects of stream, lake, estuary, and ocean pollution analysis. The book also contains ten appendices of useful tables and nomographs of pertinent data. This book provides a very good summary and review of stream, lake, estuary, and ocean pollution. This book is recommended for environmental engineering students, environmental consulting engineers, and regulatory personnel. It provides an excellent summary of the field of stream and lake analysis and modeling. Every chapter includes a significant number of questions and pertinent references.

British Library Electronic Table of Contents (United Kingdom)

Various SST indices in the Indo-Pacific region have been proposed in the literature in light of a long-range seasonal forecasting of the Indian Summer Monsoon (ISM). However, the dynamics associated with these different indices have never been compared in detail. To this end, the present work re-examines the variabilities of ISM rainfall, onset and withdrawal dates at interannual timescales and explores their relationships with El Ni?o-Southern Oscillation (ENSO) and various modes of coupled variability in the Indian Ocean. Based on recent findings in the literature, five SST indices are considered here: Ni?o3.4 SST index in December?January both preceding [Nino(?1)] and following the ISM [Nino(0)], South East Indian Ocean (SEIO) SST in February?March, the Indian Ocean Basin (IOB) mode in ...

British Library Electronic Table of Contents (United Kingdom)

Understanding the processes responsible for coastal change is important for managing our coastal resources, both natural and economic. The current scientific understanding of coastal sediment transport and geology suggests that examining coastal processes at regional scales can lead to significant insight into how the coastal zone evolves. To better identify the significant processes affecting our coastlines and how those processes create coastal change we developed a Coupled Ocean-Atmosphere-Wave-Sediment Transport (COAWST) Modeling System, which is comprised of the Model Coupling Toolkit to exchange data fields between the ocean model ROMS, the atmosphere model WRF, the wave model SWAN, and the sediment capabilities of the Community Sediment Transport Model. This formulation builds upon ...

International Nuclear Information System (INIS)

The total amount of uranium dissolved in seawater at a uniform concentration of 3 mg U/m3 in the world's oceans is 4.5 billion tons. An adsorption method using polymeric adsorbents capable of specifically recovering uranium from seawater is reported to be economically feasible. A uranium-specific nonwoven fabric was used as the adsorbent packed in an adsorption cage 16 m2 in cross-sectional area and 16 cm in height. We submerged three adsorption cages in the Pacific Ocean at a depth of 20 m at 7 km offshore of Japan. The three adsorption cages consisted of stacks of 52 000 sheets of the uranium-specific non-woven fabric with a total mass of 350 kg. The total amount of uranium recovered by the nonwoven fabric was >1 kg in terms of yellow cake during a total submersion time of 240 days in the ocean.

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on stainless steels in a borate buffer solution (pH 9.2) have been investigated by capacitance measurements and photoelectrochemistry. The study was carried out on films formed on AISI type 304 and 316 stainless steels and high purity alloys with differing chromium, nickel, and molybdenum contents. Complementary research by Auger analysis shows that the passive films are composed essentially of an inner chromium region in contact with the metallic substrate and an outer iron oxide region developed at the film/electrolyte interface. The semiconducting properties of the passive films are determined by those of the constituent chromium and iron oxides which are of p-type and n-type, respectively. Thus the influence of the alloying elements on the semiconducting properties of the passive films is explained by changes in the electronic structure of each of these two oxide regions.

Energy Technology Data Exchange (ETDEWEB)

Photocurrent and capacitance measurements of semiconductor passive films formed on metals and alloys can be used to study the electronic properties and reveal indirect information about structure and composition. The current work used these techniques to investigate the electronic properties of the passive films formed on three austenitic stainless steels, types 304L, 316L and 254SMO, in borate. Evidence was found for the existence of a large number of localised mid bandgap states, consistent with amorphous oxides. However, the flat-band potentials of the austenitic stainless steel passive films were found to be independent of both composition and measuring frequency. The most credible explanation for the bandgap values determined from photocurrent measurements is that the passive films are formed as dual layers, iron oxide outer layer and chromium oxide inner layer. This model does not need to evoke ...

Energy Technology Data Exchange (ETDEWEB)

In a work studying the corrosion and tarnishing properties of a variety of copper alloys, the alloy Cu-A110-Sn5 was found to show an excellent corrosion resistance in neutral solutions, where copper and most conventional Cu alloys are covered by thick nonprotective surface layers. The passive films formed on this alloy were characterized with electrochemical and photoelectrochemical methods. The pH dependence of the passivation and of the photocurrent behavior of the Cu-A110-Sn5 alloy clearly indicates that the passivity of this alloy in neutral solutions is due to a formation of passive film enriched with aluminum oxide. At corrosion potential a strong increase in the corrosion resistance with time is due to a gradual enrichment of the surface with aluminum oxide. This can be seen in the photocurrent spectra which change from cooper-type to aluminum-type with time. At higher applied potentials the ...

Energy Technology Data Exchange (ETDEWEB)

Passive films were formed on a high purity Fe-23 Cr alloy in acid sulfate solutions in the presence and absence of chloride ion. The resulting film composition was investigated by Auger depth profiling. The passivated samples were exposed to a 1M NaCl solution at a constant potential slightly above the critical pitting potential, and the current-time transient was measured in order to compare the relative stability of the different films. The results obtained suggest that the formation conditions influence the chloride content of the passive film and the breakdown behavior. Passive films formed in the presence of chloride contain and are slightly less stable towards breakdown. No chloride was found in films formed in sulfate and subsequently exposed to chloride well below the pitting potential.

Energy Technology Data Exchange (ETDEWEB)

Sputter-deposited tantalum (Ta) and reactively sputter-deposited Ta-nitride films were studied with respect to the passivation capability against copper (Cu) oxidation in thermal O{sub 2} ambient. A 200 {angstrom} Ta or Ta-nitride film was sputter-deposited on a 2,000 {angstrom} Cu film using a Ta target in an Ar/N{sub 2} gas mixture. With Ta passivation, Cu was not oxidized at temperatures up to 400 C, which can be further improved by using passivation of an amorphous Ta-nitride film deposited in an appropriate condition. The absence of long-range defects in the Ta-nitride film was presumably responsible for this improvement. However, sputtering-induced surface damage by excess N{sub 2} in the sputter gas mixture may reduce the passivation capability of Ta-nitride films. When the passivated Cu was oxidized, the Cu oxides always resided in the top surface region. That is, in the ...

International Nuclear Information System (INIS)

Thin passive films formed on highly corrosion-resistant type-312L stainless steel, containing 20 mass% chromium and 6 mass% molybdenum, in 2 mol dm-3 HCl solution at 293 K have been analyzed by glow discharge optical emission spectroscopy (GDOES). The stainless steel does not suffer pitting corrosion even in this aggressive solution, showing a wide passive potential region. The depth profiles obtained clearly show a two-layer structure of the air-formed and passive films: an outer iron-rich layer and an inner layer highly enriched in chromium. Alloy-constituting molybdenum is deficient in the inner layer of the passive films and is enriched in the outer layer, particularly at the active dissolution potential. The molybdenum species in the outer layer may retard the active dissolution of stainless steel, promoting the formation of stable passive films highly enriched in chromium. ...

International Nuclear Information System (INIS)

The comprehension of passivity and its protective character against corrosion is closely connected with the electronic properties of passive films. Passive films formed anodically on carbon steel in borate/boric acid solution, pH 9.2, have been characterised by electrochemical impedance spectroscopy (EIS). Mott-Schottky plots and impedance measurements were made on films formed at different potentials and times. The investigation allowed the determination of the semiconductive properties of the films. The results of the capacitance response indicate that the passive films behave like highly doped n-type semiconductors, showing that the passive film properties are dominated by iron. The value of donors density (N _D) for the passive film is of the order of 10"2"1 cm"-"3 and decreases with increasing formation time and potential, indicating that defects decrease ...

UK PubMed Central (United Kingdom)

BackgroundDinoflagellates are unicellular, often photosynthetic protists that play a major role in the dynamics of the Earth's oceans and climate. Sequencing of dinoflagellate nuclear...Full Text Available

Science.gov (United States)

The ratio of particle velocity to translation speed exceeds 1 for 98% of .... The westward movement of the meandering jet and eddy system transports nutrient- rich ...... J. Hydrometeor., 4, 1044-1066. Gedney, N., P. M. Cox, H. Douville, ...

UK PubMed Central (United Kingdom)

BackgroundFood supply from the ocean is constrained by the shortage of domesticated and selected fish. Development of genomic models of economically important fishes should assist...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Separate abstracts were prepared for 60 papers in this volume of conference proceedings. None other papers in the proceedings were previously abstracted for EDB. Also included in the proceedings but not indexed separately are six workshop summaries and a session introduction. (LEW)

Science.gov (United States)

In the IEEE Marine Technology Society OCEANS 2009 Conference, Biloxi. October 26-29, 2009. Biloxi, MS. Al-Hamdan, M.; Estes, M.; Quattrochi, D.; Thom, R.; ...

UK PubMed Central (United Kingdom)

Records of past climates contained in ice cores, ocean sediments, and other archives show that large, abrupt, widespread climate changes have occurred repeatedly in the past. These changes were especially...Full Text Available

UK PubMed Central (United Kingdom)

It is now widely accepted that novel infectious disease can be a leading cause of serious population decline and even outright extinction in some invertebrate and vertebrate groups (e.g., amphibians)....Full Text Available

Science.gov (United States)

Ocean thermal energy conversion (OTEC) plants discharge large volumes of cold water into the upper ocean. A three-dimensional, limited-area model was developed to investigate the regional influence of the far-field effluent plume created by the negatively buoyant discharge. The model was applied to discharges from a 40-MW/sub e/ OTEC plant into coastal waters characterized by various ambient ocean conditions. A typical ambient temperature structure and nutrient distribution, as well as the behavior of the effluent plume itself, were strongly modified by the discharge-induced circulation. Although temperature perturbations in the plume were small, upward entrainment of nutrients from below the thermocline was significant. The regional influence of discharges from an 80-MW/sub e/ OTEC plant, the interactions between the discharges from two adjacent 40-MW/sub e/ OTEC plants, and the effects of coastal boundary and bottom ...

Energy Technology Data Exchange (ETDEWEB)

Adenosine triphosphate (ATP) is an indicator of living biomass in marine particulates. This report details the method used by Lawrence Berkeley Laboratory to analyze particulate ATP in samples taken from oligotrophic, tropical ocean waters. It represents a synthesis of previously published methods.

UK PubMed Central (United Kingdom)

Picocyanobacteria of the genus Synechococcus are important contributors to marine primary production and are ubiquitous in the world's oceans. This genus is genetically diverse, and...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

It is often advantageous to generate power with combinations of wind and ocean waves. In fact ocean waves, their generation, propagation, dissipation are directly related to wind velocity and its duration oven the sea. In this paper an attempt has been made to demonstrate statistically to present some advantages with combined wind and ocean wave power generation. Even though many conceptual techniques and methods are possible to harness combined power generation, it is important to test feasibility of combined output as well as individual outputs mathematically. One of the major advantages of combined wind and wave power generation is to improve probability of continuous power supply (it minimises the interruptions and compensates power fluctuations with one another). Some of the major wave characteristics like wave Height (H), Time period (T), Wave length (L) significantly influence wave power generation. Interestingly, ...

Energy Technology Data Exchange (ETDEWEB)

Several Mg-Y binary ribbons with Y content up to {approx}17.9 at.% were fabricated by melt-spinning. X-ray diffraction (XRD) revealed that the phase structure changes with increasing Y content from extended solid solution to partially amorphous, and then fully intermetallic Mg{sub 24}Y{sub 5}. Anodic potentiodynamic polarization performed in 0.01 M NaCl electrolyte (pH=12) revealed improved anodic passivity behavior compared to pure Mg for all the Mg-Y alloys. X-ray photoelectron spectroscopy (XPS) revealed that the improved passivity of Mg-Y was more related to the elemental oxidation state rather than the concentration of the surface components. To study the effect of Cl{sup -} ion on the passivity behavior, anodic potentiodynamic and potentiostatic polarization were performed on Mg-17.9 at.% Y in alkaline (pH=12) NaCl electrolytes containing Cl{sup -} ion in the concentration range from 0.00 to 0.50 M. The ...

Energy Technology Data Exchange (ETDEWEB)

The structure of hydroxylated oxide films (passive films) formed on Cr(110) in 0.5 M H{sub 2}SO{sub 4} at +0.35, +0.55, and +0.75 V/SHE has been investigated by in situ scanning tunneling microscopy (STM). Cathodic reduction pretreatments at {minus}0.54, {minus}0.64, and {minus}0.74 V/SHE destroy the well-defined topography of the single-crystal electrode and they have been excluded from the passivation procedure. Two different passive film structures have been observed, depending on the potential and time of passivation. At low potential (+0.35 V/SHE), the passive film, consisting mostly of chromium hydroxide, has a noncrystalline and granular structure whose roughness suggests local variations of thickness of ca. {+-} 0.5 nm. A similar structure is observed at higher potential (+0.55 V/SHE), but only for a short polarization time. For longer polarization at 0.55 V/SHE, and at ...

Energy Technology Data Exchange (ETDEWEB)

Research performed at the Lawrence Livermore National Laboratory on the equilibrium and stability of a new class of ambient-temperature passive bearing systems is described. The basic concepts involved are: (1) Stability of the rotating system is only achieved in the rotating state. That is, disengaging mechanical systems are used to insure stable levitation at rest (when Earnshaw`s theorem applies). (2) Stable levitation by passive magnetic elements can be achieved if the vector sum of the force derivatives of the several elements of the system is net negative (i.e. restoring) for axial, transverse, and tilt-type perturbations from equilibrium. To satisfy the requirements of (2) using only permanent magnet elements we have employed periodic ``Halbach arrays.`` These interact with passive inductive loaded circuits and act as stabilizers, with the primary forces arising from axially symmetric permanent-magnet elements. ...

Energy Technology Data Exchange (ETDEWEB)

The temperature effect on corrosion behaviors of PbCaSnCe alloy in 4.5 M H{sub 2}SO{sub 4} solution was investigated by using potentiodynamic curve, electrochemical impedance spectra (EIS), Mott-Schottky plot and photocurrent response methods. It was found that PbCaSnCe alloy was in passive state in sulfuric acid solution, a passive film can be formed on alloy surface. The compositions of passive films formed at 0.9 V for 2 h under different temperatures were detected by X-ray photoelectron spectroscopy (XPS). The results showed that the film resistance and the transfer resistance decreased with the increment of the solution temperature. Mott-Schottky analysis and the photocurrent response revealed that the passive film exhibited n-type semi-conductive character, the donor density of the passive film decreased with increasing the solution temperature. Photocurrent response revealed ...

Energy Technology Data Exchange (ETDEWEB)

Type 440C stainless steel is a high-C, high-Cr martensitic steel used in applications requiring high hardness and wear resistance in combination with moderate corrosion resistance. Typical applications include precision aerospace bearings and critical components in computer disk drives. The properties of passive films formed on 440C steel were investigated using advanced electrochemical techniques with a view to establishing a method to measure film stability directly in the passivation baths. Electrochemical measurements were sensitive to the passive film properties and were able to quantify the effect of cooling rate on passive film stability. The techniques used included linear polarization, AC impedance, small amplitude cyclic voltammetry, and coulostatic transient measurements. These provided results that exhibited excellent agreement with the AC impedance technique providing the most information ...

International Nuclear Information System (INIS)

The formation and breakdown of the passive films on stainless steels are mainly controlled by ionic and electronic transport processes. Both these processes are in part controlled by the electronic properties of the oxide film. Consequently, it is vital to gain a detailed perception of the electronic properties of the passive films together with structural and compositional information for a comprehensive understanding of mechanisms behind passivity and localised corrosion. As a step towards this goal the passive films formed on two main austenitic stainless steels AISI 316L and AISI 304L in borate solution were characterised by in situ Raman spectroscopy and photocurrent spectroscopy coupled with electrochemical measurements. This revealed the formation of an Fe-Cr spinel as the dominant constituent in the passive films with more Cr enrichment in the oxide film on 316L than that of ...

International Nuclear Information System (INIS)

The chemical properties of alloys in a given environment are to a large extent governed by the surface composition. Changes of the surface composition during passivation are important features in this respect. Previous studies of single crystal Ni-Mo alloys surfaces have been reported. The aim of this work was to obtain quantitative data, for the natural oxide and the passive films formed on Ni-6% Mo(100) and (110) alloys, using Rutherford backscattering spectroscopy and nuclear reaction analysis. (author).

Energy Technology Data Exchange (ETDEWEB)

Indoor radon is a potential health hazard for the general public, especially in buildings with poor ventilation. A variety of dosemeters have been developed and used in surveys of radon concentration measurements. In this article the passive dosemeters which are based on solid state nuclear track detectors are reviewed. The principle of passive dosimetry and the factors affecting their performance are discussed. The characteristics of SSNTD materials in relation to their behaviour under different environmental conditions are tabulated and discussed. Results of radon surveys from selected studies are also presented. (Author).

Energy Technology Data Exchange (ETDEWEB)

The resistance to pitting of a Fe-17%Cr alloy in Cl[sup [minus

Energy Technology Data Exchange (ETDEWEB)

The passive films formed on 316L stainless steel in various NaCl solutions have been investigated by capacitance measurements (Mott-Schottky). Pitting parameters have been determined using the galvano-kinetic polarisation method. The obtained results reveal the existence of a shallow and a deep donor level localised in the band gap of the semiconducting oxide film. These energy levels are due to iron ions in the tetrahedral and octahedral positions. It also appears that the participation of the deep donor level effects the electric field. The study developed allows us to compare characteristic parameters of the electronic structure of the passive film to those related to pitting susceptibility. (authors) 25 refs.

Energy Technology Data Exchange (ETDEWEB)

P-implantation (10/sup 17/ ions cm/sup -2/, 40 KeV) into 304 stainless steel (ss) has been carried out, and an amorphous surface alloy was formed. Polarization studies in deaerated 1N H/sub 2/SO/sub 4/+ 2% NaCl showed that P-implantation improved both the general and localized corrosion resistance of 304 ss. A comparative study has been carried out between the implanted and unimplanted steel to determine what influence P-implantation has upon the properties of the passive film formed 1N H/sub 2/SO/sub 4/. The influence of Cl ions on pre-formed passive films was also studied. RHEED, XPS and AES were used to evaluate the nature of the passive films formed in these studies.

International Nuclear Information System (INIS)

Nickel ion radiation at 500 C was shown to have a strong effect on the surface electrochemistry and intergranular corrosion (IGC) of stainless steel (SS). Measured current densities in a 1 N sulfuric acid solution at room temperature were increased at active-passive, passive, and transpassive potentials. Radiation effects on the current decay behavior and susecptibility to IGC were similar for a fine-grained (FG) S alloy and for a very large-grained (LG) SS. Radiation-induced segregation (RIS) at the surface was believed to promote higher currents at short times, whereas segregation at grain boundaries was responsible for IG attack. Analytical electron microscopy (AEM) measurements revealed chromium and iron depletion plus Ni and silicon enrichment at grain boundaries in irradiated specimens. Si enhanced dissolution at transpassive potentials, whereas Cr depletion did the same at active-passive and ...

International Nuclear Information System (INIS)

The compositions of passive films formed on Fe-17Fr-13Ni (at. %) and Fe-18.5Cr-14Ni-1.5Mo (100) single crystals have been determined and the structure of the alloy under the film has been investigated. The alloys were passivated in 0.05M H_2SO_4 at 250 mV/SHE for 30 min. The oxygen content was measured by nuclear microanalysis using the "1"6O(d,p) "1"7O* reaction. The oxygen content in the passive film is similar for the two alloys and equal to (12#+-#2) 10"1"5 O/cm"2. The cationic compositions of the passive films have been determined by "4He channeling at two incident beam energies: 0.8 and 2.0 MeV. For the two alloys studied, a total cation content of (5#+-#2)10"1"5 at/cm"2 is found in the passive films. The corresponding thickness is about 12 A. There is an excess of oxygen, which can be attributed to the presence of hydroxyls and sulfate. A strong chromium enrichment is found ...

Science.gov (United States)

... The approach is to perform noise spectral density measurements and selected materials structure measurements on GaAs detector materials, with ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, we propose a new cooperative control method for multiple robotic systems that eliminates several issues in the discentralized control method. The proposed control method is constructed by extending a Passive Velocity Field Control (PVFC). It is easy to guarantee the stability in control, because the PVFC can keep the passivity of the controlled system. In this study, the cooperative control method is proposed and then it`s stability is proven. Moreover, it is extended so as to control an internal force and to control a virtual time. Finally, the efficiency of the proposed cooperative control method are examined by computer simulations for cooperation tasks with two manipulators. 11 refs., 7 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The problem of passively tracking a moving signal source has importance in a variety of applications such as radar, sonar, seismology, and radio astronomy. In many applications, only limited information is available about the signal source. It will be assumed here that only the signals which are detected by the sensors and the velocity of the source signal are known. The objective of this document is to present a program which passively tracks a target using an array of sensors. This program is available in MATLAB, version 3.5. The algorithm which is implemented consists of three main parts: time delay estimation, passive localization, and data post processing. Each of these parts are discussed, and the mathematical foundation for their solution given. Following, this the organization of the program is presented, and an example of its usage is given.

Energy Technology Data Exchange (ETDEWEB)

The high-temperature scanning borehole inspection system is currently being developed jointly by the Los Alamos National Laboratory (LANL) and Westfalische Berggewerkschaftskasse (WBK) of West Germany. The downhole instrument is a digital televiewer that utilized a microprocessor to digitize, process and transmit the acoustic information to the surface acquisition and control system. The primary operation of the downhole acoustic assembly uses a piezoelectric crystal acting as a receiver-transmitter which is mounted on the rotating head. The crystal emits a burst of acoustic energy that propagates through the borehole fluid with a portion of the energy reflected by the borehole wall back to the crystal. The time of travel and the amplitude of the reflected signal are conditioned by the microprocessor and transmitted along with other pertinent data to the surface data processing center. This instrument has been designed ...

DEFF Research Database (Denmark)

The multiple responses of fishes to changes in dissolved oxygen saturations have been studied widely in the laboratory. In contrast only few studies have included field observations. The objective of the present study was to evaluate the performance of a novel acoustic dissolved oxygen transmitter for field biotelemetry. The results demonstrated that the output of the transmitter was unaffected by three different temperatures (10 to 30 degrees C) and described the dissolved oxygen saturation with high accuracy (r(2) > 0.99) over the entire range of 0 to 191% saturation. The response time (>= 90% of end value) of the transmitter was 12 s both in terms of decreasing (100 to 0%) and increasing (0 to 100%) oxygen saturations. When externally attached to fishes the present findings support the use of the transmitter for reliable dissolved oxygen measurements on individuals living in environments that may change both temporally and spatially with regard to ambient ...

Science.gov (United States)

Field surveys were conducted to assess the community annoyance potential from electromagnetic interference to television reception (TVI) and acoustic emissions associated with the operation of a Darrieus-type, vertical axis wind turbine (VAWT). The type and extent of interference to nearby television reception was evaluated using a 17 meter VAWT. A series of measurements of observed interference levels were made at a number of sites in the turbine vicinity employing the locally available VHF and UHF television signals as sources. A simple theoretical model was developed for analyzing the TVI produced by the Darrieus turbine. Using this model in conjunction with the field measurements, it was found the Darrieus/VAWT produces the same amount of interference on the lower VHF channels as a horizontal axis turbine with a comparably sized blade scattering area, but less on all other channels.

Energy Technology Data Exchange (ETDEWEB)

Seismic stratigraphy and sedimentological studies of the Gemlik Gulf in the Sea of Marmara, Turkey, have been carried out. For this purpose, 19 lines totaling 189 km of excellent quality, high-resolution seismic data were recorded. Four major acoustic units were identified in the seismic profiles. Three were sedimentary units: irregular layered, cross-layered and well-layered; and the fourth was an acoustic basement which is probably composed of crystalline volcanic rocks. Some local areas in the Neogene formation contain gas accumulations. The formation of faults in E--W and N--S directions can be explained by the existence of shear stresses in the Gulf. The bathymetric map shows good accommodation with the shore line as does the tectonic map.

CERN Document Server

Acoustic metamaterials with negative effective mass below a cut-off frequency are studied. An equivalent mass-spring structure is firstly proposed for such metamaterials, the effective mass is found to follow the Drude model: being negative below a specific frequency. The peculiar behavior is then verified by transmission experiments operating in the low-frequency regime. Inspired by the mass-spring model, we investigate the two-dimensional elastic waveguide with clamped boundaries and attribute the bandgap occurring below a critical frequency to negative effective mass density. The finding helps us to design a new acoustic Drude metamaterial, which enables shearing and bending deformations, in contrast to the membrane-type ones. Both simulation and experimental results show that the proposed metamaterial exhibits negative effective mass below 1200 Hz, thus opening broadband applications in vibration and noise controls.

British Library Electronic Table of Contents (United Kingdom)

Orthogonal frequency division multiplexing (OFDM) can fully use the frequency band and transmit data at high speeds. The ADSP-TS101 is a high performance digital signal processor (DSP) with good properties that include parallel processing and a high speed. Aimed at the real-time processing requirement of the OFDM algorithm, an underwater acoustic communication system with real-time processing capability is carried out. The system is mainly composed of multiple ADSP-TS101s, a multi-channel synchronous sample module and a field programmable gate array (FPGA) chip. The multiprocessor structure is made up of a cluster/data flow associated multiprocessing parallel processing structure as the operation kernel, and a multi-channel synchronous sample module is designed to realize no phase warp amo...

Energy Technology Data Exchange (ETDEWEB)

The use of dendrimers for preparing chemically sensitive interfaces for detecting volatile organic compounds (VOCs) using surface acoustic wave (SAW) device transducers is described. Specifically, the synthesis of the dendrimers and the means by which they are affixed to SAW devices is discussed, followed by a detailed spectroscopic analysis of the surface-confined dendrimers and a discussion of their interaction with different VOCs. Most of these preliminary experiments focus on dendrimer surface modification using benzoylchloride, which leads to phenyl terminal groups linked to the dendrimer via amide groups. The results of this study lead us to conclude that dendrimers: (1) provide general specificity towards classes of functional groups and are therefore suitable for array-based sensing schemes; (2) are intermediate in structure between monolayers and polymers and exhibit the desirable properties of both; (3) can be straightforwardly attached to the surfaces of ...

Energy Technology Data Exchange (ETDEWEB)

The improvement in the functions of the viscous flow calculation method VEGA-SHIP around a ship and the expansion of application range were described as the numerical flow simulation in ship and ocean engineering and at the same time application examples to the ocean engineering by the general-purpose flow simulation code FLOW-3D handling the non-steady flow with a free surface were introduced as the numerical simulation regarding such products as a water gate and a dam. In the VEGA-SHIP, water surface was handled as a fixed wall so that wave could not be calculated. Therefore, an algorithm for calculating wave on the water surface was added to the VEGA-SHIP and a calculation method simultaneously considering the creation of wave around the ship and viscosity was developed. The FLOW-3D was used to calculate the phenomenon where inside liquid moved greatly due to the oscillation of a tank and hit against and damaged the tank ceiling in the tank, ...

British Library Electronic Table of Contents (United Kingdom)

A parameterized surface wave-induced vertical mixing (B"v) is incorporated into the Modular Ocean Model version 4 (MOM4). A comparison of the two numerical experiments with and without B"v shows that B"v can significantly improve the upper-ocean (20-100m) simulation in summer. The simulated upper-ocean temperature errors are reduced in summer due to the surface wave-induced vertical diffusive heat flux. The non-breaking-wave-induced vertical mixing can increase the probability of the simulated SST biases between -1^oC and 1^oC from 64% to 76% in the Southern Hemisphere (60^oS-10^oS) in January, and from 66% to 75% in the Northern Hemisphere (10^oN-60^oN) in July. The averaged mixed layer depth (MLD) simulated by the MOM4 without B"v is 14.4m shallower than the observations in 10^oS-60^oS i...

DEFF Research Database (Denmark)

The tidal motion of the ocean water through the ambient magnetic field, generates secondary electric field. This motionally induced electric field can be detected in the sea or inland and has a potential for electrical soundings of the Earth. A first goal of the paper is to gain an understanding of the global distribution of the electric signal due to tidal ocean flow. We simulate the electric signals for two tidal constituents - lunar semidiurnal (M2) and diurnal (O1) tides. We assume a realistic Earth's conductivity model with a surface thin shell and 1-D mantle underneath. Simulations demonstrate that in some coastal regions the amplitudes of the electric field can reach 100 mV/km and 10 mV/km for M2 and O1 tides respectively. The changes of lithosphere resistance produce detectable changes in the tidal electric signals. We show that our predictions are in a good agreement with observations.

International Nuclear Information System (INIS)

Austenitic stainless steels (304-type) have been implanted with nitrogen ions in order to investigate the effects of implanted nitrogen on their electrochemical behaviour and on the nature of the passive film formed on the steels in acid (0.5M H_2SO_4). Alloys with two nitrogen doses have been prepared (2.5x10"1"6 and 2x10"1"7 N atoms/cm"2). The implanted alloys have been characterized by "1"5N-NRA (nuclear reaction analysis) and XPS (X-ray photoelectron spectroscopy). Alloy surfaces with well-defined N concentrations were prepared, prior to the electrochemical measurements, by argon-ion sputtering of the implanted material for a fixed time in order to reach a well-defined point on the nitrogen depth profile. The samples were then transferred without exposure to air to an electrochemical cell mounted in an inert gas glove box. The implanted nitrogen modifies the electrochemical behaviour of the alloy. The anodic dissolution in the active state is enhanced, and the ...

Energy Technology Data Exchange (ETDEWEB)

The state of lithium electrode surface after contact with triethylamine-modified propylene carbonate solutions of lithium perchlorate was studied using the pulse galvanostatic technique as well as methods of SIMS and electron microscopy. It was shown that amine added into the solutions stabilizes the state of lithium and prevents the formation of a secondary porous passive film on the lithium surface. Chemical composition of the primary film remains unchanged. Certain properties of passive films formed in electrolyte solutions studied were evaluated.

Energy Technology Data Exchange (ETDEWEB)

The passivity and breakdown of passivity of 1018 carbon steel in propylene carbonate (PC) and 1,2-dimethoxyethane (DME) mixtures with 0.5 molar lithium hexafluoroarsenate supporting electrolyte were examined via several electrochemical and surface analytical methods. The PC-DME/0.5 M LiAsF{sub 6} mixtures ranged from 10 to 90 mol % PC. The results from the PC/DME mixtures were compared to passivating mechanisms found in pure PC and DME solutions. In PC-rich mixtures, the breakdown of passivity occurred near the oxidation potentials of either organic solvent. Premature breakdown of the carbon steel in PC-DME mixtures occurred at sulfide inclusions as was observed earlier in PC/0.5 M LiAsF{sub 6} solutions although passive films attempted to form at these inclusion sites in mixtures containing at least 10 mol % DME. As the DME content increased in the PC-DME mixtures, the ...

Science.gov (United States)

Traditionally, market researchers have sought some formula to predict the acceptance of a new product or innovation in advance of its introduction. Perhaps a universal marketing formula will never be found. However, a summary of 3000 research studies, conducted in the United States and in other countries of the world, on how people accept new ideas promises more insight into the subject of the marketing of passive design and products than ever before.

International Nuclear Information System (INIS)

The study by impedance and photoelectrochemical measurements of passive films formed on an AISI 304 type stainless steel shows that important parameters of the electronic structure of these films are modified under #alpha# irradiation, namely: width of the space charge region, donors concentration and diffusion length for minority carriers. The consequences of #alpha# irradiation on localized corrosion processes are discussed.

International Nuclear Information System (INIS)

By means of ESCA the composition and the thickness of passive films formed on austenitic stainless steels were investigated after the attack of nitric acid at various temperatures and acid concentrations. The outermost layers of the oxide film consist of SiO_2, then a layer rich of Cr-oxid follows, containing also some Mo in the four- and sixvalent state. Ni does not contribute to the oxide film. Cr is also enriched in the metal just below the oxide film. (orig.).

Energy Technology Data Exchange (ETDEWEB)

A computational model has been developed to calculate the potential and current distributions in the electrolyte phase and on the electrode surface for a system in which a part of the anode is passivated while the rest remains in the active dissolution state. The computation employs the finite element method allied with a boundary variation and a trial and error technique. From the obtained distributions, the location of the boundary between the active and passive regions on the anode can be predicted. In the case of a crevice, this means that a critical distance into the crevice exists beyond which active corrosion (crevice corrosion) takes place. In addition to the active/passive behavior of the material, solution conductivity, applied potential at the sample's outer surface, crevice gap and depth dimensions, and passive current density influence this critical distance to different degrees. ...

International Nuclear Information System (INIS)

This paper deals with the characterization of passive films formed on stainless steel (26% Cr and 0 to 3%Mo). The influence of the applied passivation potential and the effect of molybdenum additions to steel upon the composition profiles of passive films formed in an aqueous NaCl solution (3.5% at pH 2.5) are studied. The technique involved is Auger electron spectroscopy combined with ion sputtering. Some electrochemical techniques have been used in conjunction. A quantitative approach of the Auger spectra during the progressive removal of the passive film is described. The peak-to-peak height of the Auger lines are treated in order to yield the atomic fraction of the various elements present in a given subsurface layer. The analytical study of the film by electron spectroscopy indicates that molybdenum plays a part at the metal-oxide interface where this element acts on the chromium diffusion process. ...

Energy Technology Data Exchange (ETDEWEB)

Pitting behavior of alloy 800 was investigated as a function of temperature and prefilming in high-temperature water. The behavior was characterized in terms of pitting potential (U{sub p}) and pit density (n{sub p}). U{sub p} decreased with increasing temperature and chloride activity. Prefilming of test coupons over a period between 100 h and 5,000 h in ammoniated water at 300 C had no apparent influence on U{sub p} at room temperature, 180 C, and 300 C. However, the number of pits in prefilmed coupons was much higher than in coupons covered with an air passive layer. The effect of prefilming on pit nucleation was investigated in detail with regard to a model and test methods developed by Bianchi, et al. Density of pits in prefilmed coupons was at least 1 order of magnitude higher than in air passive coupons. Maximum pit density was measured after a prefilming period of 100 h. The effect was discussed in terms of Bianchi`s model and in terms ...

Energy Technology Data Exchange (ETDEWEB)

the development of lithium metal batteries is hindered by the bad reversibility of the Li{sup +}/Li pair, due to dendrites formation which limits the amount of active matter and can generate short-circuits. The chemical and electrochemical phenomena which take place at the electrode/organic electrolyte interface lead to the formation of a complex passivation film which is of prime importance for the functioning of this type of batteries. The in-situ infrared reflection spectroscopy is well adapted to the chemical study of the passivation layer. Two different techniques were used: the substraction normalized interfacial transform infrared spectroscopy (SNIFTIRS) and the electro-chemically modulated infrared reflectance spectroscopy. These methods have shown that the passivation layer that develops on the surface of the lithium electrode in contact with organic solutions (propylene carbonate, ethylene carbonate and ...

Energy Technology Data Exchange (ETDEWEB)

Scanning electrochemical microscopy (SECM) was applied to evaluate the heterogeneity of a passive film formed on a pure iron electrode in deaerated pH 8.4 borate solution. A probe current image of SECM was measured with a tip-generation/sub-strate-collection (TO/SC) mode in deaerated pH 8.4 borate solution containing 0.03 moldm{sup -3} Fe(CN){sub 6}{sup 4-} as a mediator. The difference in thickness of passive films formed on two iron plates at different potentials could be evaluated from the probe current image. The probe current image of the passivated iron surface with distinctive crystal grains was composed of the patch patterns, the shapes of which coincided completely with the shapes of the substrate crystal grains. The probe current flowed above the grain surface oriented to {l_brace}100{r_brace} plane was less than that above the grain surface oriented to {l_brace}110{r_brace} or {l_brace}111{r_brace} plane. The ...

International Nuclear Information System (INIS)

III--V based devices such as field effect transistors, heterojunction bipolar transistors, and lasers often have surface leakage and thermal degradation problems due to surface states which pin the Fermi level to the midgap. Sulfur based passivation processes are known to improve device performance by altering surface-state densities. We have developed a voltage-controlled anodic sulfur passivation scheme using Na_2S dissolved in ethylene glycol. Our process has repeatedly produced a #approx#25% improvement in peak output power near the catastrophic damage limit in visible (#lambda#=670 nm) AlGaInP edge-emitting lasers. The threshold current density before and after passivation, and the I--V characteristics before and after catastrophic failure, were essentially unchanged indicating that passivation raises the threshold for facet damage.

British Library Electronic Table of Contents (United Kingdom)

Many of the world's coral reefs suffered high coral mortality during the 1998 ENSO, with the highest mortality in the western Indian Ocean (WIO). A meta-analysis of field data on change in coral cover across the 1998 ENSO event was conducted for 36 major reef areas in the WIO, and relationship of the change with the historical sea-surface temperature (SST) variability investigated. WIO reefs were categorized into three major SST groups of differing coral cover change. Cover change was negatively associated with standard deviation (SD) SST until about SD 2.3, with increasing flatness of the SST frequency distributions. It increased with further increase in SD as the SST distributions became strongly bimodal in the Arabian/Persian Gulf area. The study indicates that environmental resistance/...

International Nuclear Information System (INIS)

"1"2"9I global distribution due to biogeochemical cycle in environment reservoirs has been studied. It is shown that during the operation of nuclear fuel cycle facilities and at a modern level of the decontamination factor the "1"2"9I concentration in some natural media (soil, the Earth biosphere, ocean mixing layer) will increase by 4-5 orders. Recommended gradual increase of the decontamnation factor in time for conserving the "1"2"9I concentration level not exceeding one order in comparison with modern one is given. At that to the end fof the centary the decontamination factor must be of an order of 1x10"4 in the case of "1"2"9I intake to the ocean mixing layer and of 1x10"5 in the case of its intake to the atmosphere.

Energy Technology Data Exchange (ETDEWEB)

The Offshore Comet is a modern offshore drilling rig with a hydraulic-cylinder-actuated jacking (raising and lowering) system. Hydraulic-cylinder jacking provides a safe and efficient method for placing the rig at the desired height above the water and insuring that it can withstand the expected heavy loads imposed by machinery, supplies, and the ocean environment. The drilling rig consists of a steel-hulled barge that is floated to the site and then supported during drilling operations by four steel triangular-cross-section lattice legs. The legs are planted firmly on the ocean bottom by a procedure called preloading. Each leg with its integral footing weighs 657 tons. The barge with its deck load can weigh up to 9200 tons.

British Library Electronic Table of Contents (United Kingdom)

Regional Ocean Modeling System (ROMS v 3.0), a three-dimensional numerical ocean model, was previously enhanced for shallow water applications by including wave-induced radiation stress forcing provided through coupling to wave propagation models (SWAN, REF/DIF). This enhancement made it suitable for surf zone applications as demonstrated using examples of obliquely incident waves on a planar beach and rip current formation in longshore bar trough morphology (Haas and Warner, 2009). In this contribution, we present an update to the coupled model which implements a wave roller model and also a modified method of the radiation stress term based on Mellor (2008, 2011a,b,in press) that includes a vertical distribution which better simulates non-conservative (i.e., wave breaking) processes and ...

British Library Electronic Table of Contents (United Kingdom)

Mesopelagic zooplankton may meet their nutritional and metabolic requirements in a number of ways including consumption of sinking particles, carnivory, and vertical migration. How these feeding modes change with depth or location, however, is poorly known. We analyzed fatty acid (FA) profiles to characterize zooplankton diet and large particle (>51?m) composition in the mesopelagic zone (base of euphotic zone ?1000m) at two contrasting time-series sites in the subarctic (station K2) and subtropical (station ALOHA) Pacific Ocean. Total FA concentration was 15.5 times higher in zooplankton tissue at K2, largely due to FA storage by seasonal vertical migrators such as Neocalanus and Eucalanus. FA biomarkers specific to herbivory implied a higher plant-derived food sou...

British Library Electronic Table of Contents (United Kingdom)

Spacecraft studies of the three terrestrial planets with atmospheres have made it possible to make meaningful comparisons that shed light on their common origin and divergent evolutionary paths. Early in their histories, all three apparently had oceans and extensive volcanism; Mars and Earth, at least, had magnetic fields, and Earth, at least, had life. All three currently have climates determined by energy balance relationships involving carbon dioxide, water and aerosols, regulated by solar energy deposition, atmospheric and ocean circulation, composition, and cloud physics and chemistry. This paper addresses the extent to which current knowledge allows us to explain the observed state of each planet, its planetology, climatology and biology, within a common framework. Areas of ignorance...

Science.gov (United States)

It is shown that the extended softening in k space of the [111] transverse acoustic phonon in Nb3Sn seen recently by neutron measurements is in agreement with the predictions of a phenomenological Landau description of the structural phase transition in the A-15 compounds. This indicates the feasibility of a calculation of the partial phonon density of states of modes directly coupled to the order parameter driving the structural transition, as a function of temperature.

Energy Technology Data Exchange (ETDEWEB)

During its jubilee, the French building technical and scientific centre (CSTB) has organized a colloquium about the future tendencies of buildings evolution in the 20 forthcoming years: autonomy in energy production and wastes or effluents management, reduction of water consumption and management of water, hot water production and space heating, bio-sensors for the management of indoor air-quality, control of noise environment using active acoustic systems etc.. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

The stability of accretion disks against short wavelength perturbations is analyzed. The disk is shown to be unstable to slow thermal perturbations propagating in the z-direction for sufficiently high values of the stress parameter ..cap alpha.. and sufficiently low values of the ratio of gas to total pressure. The acoustic flux from the ''middle region'' of the disk is estimated and discussed.

International Nuclear Information System (INIS)

Purpose: To evaluate the outcome of repeat stereotactic radiosurgery (SRS) for acoustic neuromas, we assessed tumor control, clinical outcomes, and the risk of adverse radiation effects in patients whose tumors progressed after initial management. Methods and Materials: During a 21-year experience at our center, 1,352 patients underwent SRS as management for their acoustic neuromas. We retrospectively identified 6 patients who underwent SRS twice for the same tumor. The median patient age was 47 years (range, 35-71 years). All patients had imaging evidence of tumor progression despite initial SRS. One patient also had incomplete surgical resection after initial SRS. All patients were deaf at the time of the second SRS. The median radiosurgery target volume at the time of the initial SRS was 0.5 cc and was 2.1 cc at the time of the second SRS. The median margin dose at the time of the initial SRS was 13 Gy and was 11 Gy at the time of the second ...

International Nuclear Information System (INIS)

This report focuses on a better understanding of the physical phenomenon related to the enhancement of boiling and non-boiling heat transfer by applying ultrasonic waves. Experimental results obtained both in a pool of water and in a vertically upward water flow proved clearly that macroscopic acoustic steam induced by ultrasonics is a major contribution to heat transfer augmentation. (author).

International Nuclear Information System (INIS)

The universal depression of the superconducting transition temperature T/sub c/ in disordered A-15 compounds is examined. Existing energy-band calculations are used to calculate the density of electron states, which is possibly enhanced by disorder in some cases such as Nb_3Ge. The dramatic drop in T/sub c/ in Nb_3Ge at a critical value of the resistivity is attributed to overdamping of acoustic plasmons which decreases the electron pairing interaction despite small changes in the density of states.

Energy Technology Data Exchange (ETDEWEB)

X-ray photoelectron spectroscopy and ex situ scanning tunneling microscopy measurements have been combined to investigate the thickness, the chemical composition, and the structure of passive films formed in 0.5 M H{sub 2}SO{sub 4} on Fe-22Cr(110). Aging under polarization at +500 mV/SHE causes a dehydration (anodic) reaction of the outer chromium hydroxide layer of the passive film. This anodic reaction results in a thickening of the inner mixed Cr(III) and Fe(III) oxide layer enriched in Cr{sub 2}O{sub 3}. It also causes a coalescence of the oxide nuclei of the passive film and a crystallization of the inner Cr{sub 2}O{sub 3}. It also causes a coalescence of the oxide nuclei of the passive film and a crystallization of the inner Cr{sub 2}O{sub 3} oxide layer in epitaxy with the substrate. The epitaxial relationship is {alpha}-Cr{sub 2}O{sub 3}(0001) {parallel} Fe-22Cr(110) with three different ...

Energy Technology Data Exchange (ETDEWEB)

Alloy 600 is used as a material for steam generator tubing in pressurized water reactors(PWR) due to its high corrosion resistance under PWR environment. In spite of its corrosion resistance, stress corrosion cracking(SCC) has occurred on the primary side as well as the secondary side of the tubing. Oxide on steel surfaces in aqueous solution above 100 .deg. C is composed of duplex film structure. Inner layer of the oxide is dense and less porous, which is formed by growth of oxide layer on metal surface. Outer layer of the oxide is loose adhesive, which is formed by dissolution precipitation mechanism. Growth processes occur at the metal/oxide and oxide/electrolyte interfaces and are controlled by transport of the layer forming species through the layer, i.e. by the inward diffusion of oxygen including electrolyte species and the outward diffusion of metal cations. Understanding of basic electrochemical behaviors about anodic dissolution and passivation of bare ...

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion and trans-passive dissolution of 316 stainless steel in solution containing five percent of commercial bleaching liquid was investigated by employing potentiodynamic polarization method and recording corrosion potential during immersion. Today commercial bleaching liquids are widely used as cleaner additives, therefore, those house appliances made from stainless steels are in contact with aqueous solution containing bleaching liquid. This may cause sever localized corrosion and trans-passive dissolution. In order to investigate the possibility of trans-passive dissolution of stainless steel by bleaching liquid, potentiodynamic polarization and recording variation of corrosion potential of specimens were carried out in 0.2 M Na{sub 2}SO{sub 4} solution containing 5 %wt. commercial bleaching liquid. A 500 mV drop in trans-passive potential and also instantaneously ennobling corrosion ...

Energy Technology Data Exchange (ETDEWEB)

Part I of this thesis is on long-term iceberg collision-risk assessment methods for fixed offshore structures. Estimates for the long-term probability that an iceberg will hit a fixed offshore structure are based on estimates of the total volume of produced iceberg, a model for the size distribution of icebergs and a description of how iceberg trajectories ``fill`` the plane (the ocean`s surface). Part II of the thesis discusses methods for analysis of low resolution data in the sense that the size of the area covered by each pixel is not small compared to the dominating floes. Still, this type of data can provide estimates of the ice extent (and hence the ice edge) and ice concentration. The estimates of the ice edge (at least) seem to be physically significant in the sense that ``in some way`` they can reflect ice drift in an image time sequence. A priori this is far from obvious. A central idea is that the ``ice edge`` is close to a transition zone between two ...

Wastenet

... The National Oceanography Centre, Southampton is one of the world's leading research centres for the study of ocean and earth sciences. Southampton General Hospital One of the country's leading teaching hospitals and the base for the University's School of Medicine. Winchester School of Art Founded in 1863, Winchester School of Art is based 12 miles (20 kilometres) north of Southampton in the historic city of Winchester,...

Energy Technology Data Exchange (ETDEWEB)

This report highlights the significance of the geological sciences to the nation and to society. Discussions include understanding plate tectonics and surface processes, exploring the continental crust, ocean basins and the deep earth, applications of geology to social problems such as mineral resources, waste disposal, siting of critical facilities, geological hazards, water resources management, and coastal zones. The state of health of geological research is also discussed. (ACR)

Wastenet

... 01, 2009 | Rate It Marine Technology Society https://www.mtsociety.org/home.aspx emphasizes the importance of marine technology as it applies to global issues, encourages marine technology education and facilitates the use of marine technology in managing marine resources Added: Mar. 11, 2010 |...

UK PubMed Central (United Kingdom)

The oceanic bathypelagic realm (1000–4000 m) is a nutrient-poor habitat. Most fishes living there have pelagic larvae using the rich waters of the upper 200 m. Morphological...Full Text Available

Environmental Research Database

DescriptionRemote sensing of the sea surface from satellites in near-polar orbits has contributed greatly to our understanding of the links between physical and biological processes in marine systems. However most of this progress has been made in open oceanic waters or major upwelling areas, and many unresolved problems are encountered in coastal regions and shelf seas. In these optically complex waters, quantitative remote sensing requires a more sophisticated interpretation strategy than that implemente [continued...

Energy Technology Data Exchange (ETDEWEB)

Ammonia is a common and highly toxic pollutant which, in sufficient quantities, will adversely affect aquatic organisms. This ammonia criteria document for salt water will allow establishment of regulatory standards for ammonia discharge into estuaries, near coastal zones and oceans. Possible adverse impacts in highly sensitive and abundant ecosystems such as estuaries make regulation particularly important.

International Nuclear Information System (INIS)

Passive films, formed on annealed and cold worked AISI 304 stainless steel in hot chloride media, were examined using polarization resistance and impedance measurements. The obtained results show the influence of cold work on film conductivity, which can be correlated to conditions of susceptibility to stress corrosion cracking. Capacitance measurements, using the Mott-Schottky approach, revealed that a change from n to p type semi-conductivity is associated to susceptible conditions with an increase in the doping density estimated for cold worked samples in the presence of chloride. It is assumed that p-type semi-conductivity of the passive film together with the position of the flat band potential has a strong influence on the dissolution processes at the corrosion potential. Based on this analysis the influence of plastic deformation, at the dislocation scale, is discussed. (authors)

Energy Technology Data Exchange (ETDEWEB)

Red mud suspensions are studied as passivating agents for iron in alkaline chloride media. Red mud particles in alkaline media are negatively charged, and can absorb considerable amounts of protons without significant changes in pH. These particles adhere easily to an iron surface forming aggregates of heterogeneous shape, smaller than 10 {mu}mx10 {mu}m. These adhered particles recrystallise on potential cycling, and hinder metal dissolution and magnetite formation. Carbon steel samples passivated in red mud suspensions become resistant to corrosion in alkaline chloride media. Corrosion potential versus time records and impedance spectroscopy measurements allow formulating some hypotheses about the inhibiting mechanism.

Energy Technology Data Exchange (ETDEWEB)

Thin passive layers of uranium nitride were formed by nitriding pure metallic uranium in non-equilibrium, low pressure radio-frequency plasma of nitrogen. Plasma nitriding at low substrate temperature of 230 C-250 C was found to cause the formation of adherent layers of uranium sesquinitride ({alpha}-U{sub 2}N{sub 3}) which provide a considerable protection against hydrogen attack. The characteristics of these passivation layers were determined by X-ray diffraction and Auger electron spectroscopy. The incipient hydriding kinetics of the plasma-treated samples were compared with those of untreated and nitrogen-ion implantation ones, utilizing a hot-stage microscope that was monitored continuously with a TV camera and videotape. (orig.)

International Nuclear Information System (INIS)

The effect of surface treatment on the characteristics of the passive film on a super duplex stainless steel is addressed. Auger Electron Spectroscopy (AES) has been used to provide in-depth chemical profile analyses of the passivation film. This study showed that the constitution of the film is largely dependent on the electrolytic conditions under which it is produced or to which it is submitted. The passive films formed by polarisation in an alkaline solution (boric-borate solution) consist of two regions, an inner region rich in chromium and an outer region rich in iron, whilst the films produced in acid solution only present the chromium - rich region. The film thickness is also greatly affected by the polarisation conditions. It can vary from ca. 8 monolayers to about 20 monolayers for cathodically and anodically polarised specimens respectively. The microstructure of weldmetal is also discussed. (author)

International Nuclear Information System (INIS)

In this work passive films formed in AISI 304 stainless steel were envisaged as semiconductors and studied by means of photoelectrochemistry and Mott-Schottky plots. The passive films were potentiostatically formed at different potentials (0.2-0.8V) in a basic borate/boric acid solution without and with addition of NaCl (0.5 and 1g/l) and at various temperatures in the range 8-60"oC. The influence of these parameters on the photocurrent, quantum efficiency, bandgap energy and density of charge carriers was determined. The results show that the experimental conditions at which the films are formed influence the semiconductive properties of the film, which seem to be related to the higher or lower stability of the film. An Arrhenius type of relationship was also found between the density of charge carriers and temperature, leading to the determination of an activation energy. (author) 13 refs., 7 figs.

International Nuclear Information System (INIS)

Austenitic stainless steels have been implanted with molybdenum ions (Mo"+, 100 keV, 2.5 x 10"1"6 atoms cm"-"2). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of #approx# 1000 A with a maximum molybdenum concentration of #approx# 9 at.% Mo located at #approx# 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H_2SO_4 have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer ...

International Nuclear Information System (INIS)

The influence of small amounts of alloying elements (0.36% Cu and 0.47% Cr) on the semiconducting properties of passive films formed on weathering steels was investigated either in tetraborate/boric acid buffer solution (pH 9.2) or artificial atmospheric environment (SO_2-containing environment). The electrochemical behaviour was assessed by potentiodynamic polarisation, capacitance measurements and photoelectrochemistry. The chemical characterisation of the films was carried by Auger electron spectroscopy. The polarization results obtained in the buffer solution show that the addition of chromium decreases the passive current density. The capacitance results show that the films behave as an n-type semiconductor with shallow and deep donor levels situated in the forbidden gap. The presence of copper seems to affect the density of the shallow and of the deep donor levels in the forbidden gap, and as chromium, it also decreases the doping density ...

Energy Technology Data Exchange (ETDEWEB)

Passive films, formed on annealed and cold worked AISI 304 stainless steel in hot chloride media, were examined using polarization resistance and impedance measurements. The obtained results show the influence of cold work on film conductivity, which can be correlated to conditions of susceptibility to stress corrosion cracking. Capacitance measurements, using the Mott-Schottky approach, revealed that a change from n to p type semi-conductivity is associated to susceptible conditions with an increase in the doping density estimated for cold worked samples in the presence of chloride. It is assumed that p-type semi-conductivity of the passive film together with the position of the flat band potential has a strong influence on the dissolution processes at the corrosion potential. Based on this analysis the influence of plastic deformation, at the dislocation scale, is discussed. (authors)

Energy Technology Data Exchange (ETDEWEB)

The possibility has been explored of using a laser scattering technique to detect the imminent onset of rock activity associated with gas outbursts. The instrument described in this paper provides a sensitive, remote and rapid means of passively monitoring micro-seismic activity at the exposed face.

UK PubMed Central (United Kingdom)

Few diseases exemplify the integration of research from bench to bedside as well as neonatal lupus, often referred to as a model of passively acquired autoimmunity. In essence, this disease encompasses...Full Text Available

Science.gov (United States)

Contents: Energy Use; Building Fabric Performance; Ventilation and Infiltration; Passive Solar Design; Heating Systems and Controls; Hot and Cold Water Provision; and Lighting and Electrical Appliances.

Energy Technology Data Exchange (ETDEWEB)

Described herein are effects of nitrogen dissolved in steel on passivity and pitting corrosion, as one of the major corrosion phenomena observed in stainless steel. Mechanisms involved in controlling pitting corrosion by nitrogen are also discussed. Nitrogen contained in austenic stainless steel is concentrated in the surface area, in particular in the vicinity of the interface between the passive film and metal matrix. Nitrogen tends to decrease critical current density in an acid, when it is added to steel of high critical current density (approximately 1mA/cm{sup 2} or higher). This phenomenon is considered to result from accumulation of nitrogen preferentially in the surface area to prevent dissolution of steel. Nitrogen dissolved in the austenic phase improves resistance of the steel to pitting corrosion. This phenomenon is considered to result from controlled decrease in pH level during the initial stage of pitting corrosion, ...

International Nuclear Information System (INIS)

Semiconducting properties of passive films formed on AISI 304 stainless steel grade were investigated by capacitances measurements in chloride containing aqueous solutions for different surface finishes: BA (bright annealing in hydrogen containing atmospheres) and 2B (standard annealing in oxidising atmospheres followed by pickling in acid, then water rinsing). Mott-Schottky analysis shows that for high enough electrode potential, and whatever the surface finish, the films behave like n-type semiconductors. 2B passive film appears to be more donor-doped than BA one and the density of donor states increases with chloride concentration. The electron donor levels are assumed to be generated by negatively charged cations vacancies produced by the chloride ions reaction with the outer passive film. This reaction looks easier for 2B than BA condition, which explains why BA resists better than 2B to pit nucleation.

Energy Technology Data Exchange (ETDEWEB)

The primary scope of this study is to establish the analysis technology for the advanced reactor designed on the basis of the passive and inherent safety concepts. This study is extended to the application of these technology to the safety analysis of the passive reactor. The study was performed for the small and medium sized reactor and the large sized reactor by focusing on the development of the analysis technology for the passive components. Among the identified concepts the once-through steam generator, the natural circulation of the integral reactor, heat pipe for containment cooling, and hydraulic valve were selected as the high priority items to be developed and the related studies are being performed for these items. For the large sized passive reactor, the study plans to extend the applicability of the best estimate computer code RELAP5/MOD3 which is widely used for the safety analyses of the ...

Science.gov (United States)

properties such as effective particle size, thermody- namic phase (water, ice), cloud-top properties ...... Green, R.O., and J.E. Conel, 1995: Movement of ..... vertical hydrometeor profiles from passive micro- wave sensors. IEEE Trans. ...

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to passivation-free solid-state rechargeable batteries composed of Li.sub.4 Ti.sub.5 O.sub.12 anode, a solid polymer electrolyte and a high voltage cathode. The solid polymer electrolyte comprises a polymer host, such as polyacrylonitrile, poly(vinyl chloride), poly(vinyl sulfone), and poly(vinylidene fluoride), plasticized by a solution of a Li salt in an organic solvent. The high voltage cathode includes LiMn.sub.2 O.sub.4, LiCoO.sub.2, LiNiO.sub.2 and LiV.sub.2 O.sub.5 and their derivatives.

Energy Technology Data Exchange (ETDEWEB)

Neutron spectra measured in the FFTF In-Reactor Thimble (IRT) by proton recoil proportional counters, proton recoil emulsions, and passive dosimeters have been evaluated and compared with each other and with three-dimensionl diffusion theory calculated spectra for the purpose of validating the passive dosimeter spectrum adjustment technique. The least squares data adjustment code, FERRET, was used to combine measured reaction rates, calculated spectra, and dosimeter cross sections, resulting in adjusted spectra and cross sections with uncertainties and correlations that properly account for uncertainties and correlations on the input parameters.

Energy Technology Data Exchange (ETDEWEB)

We report on multijunction GaInP/GaAs photovoltaic cells with total-area efficiencies of 29.5% at one-sun concentration and air mass (AM) 1.5 global and 25.7% one-sun, AM0. These values represent the highest efficiencies achieved by any solar cell under these illumination conditions. Three key areas in this technology are identified and discussed: the grid design, front surface passivation of the top cell, and bottom surface passivation of both cells. Aspects of cell design related to its operation under different solar spectra and under concentration are also discussed.

International Nuclear Information System (INIS)

This paper reports several design options for improved passive circulation flow investigated for use in small, modular liquid metal cooled reactors (LMRs). The purpose is to enhance the transition to natural convection cooling following loss of forced circulation flow, reducing thermal transients experienced by the fuel and possibly eliminating the need for emergency pony-motor flow. Design details to minimize pressure drops may also enhance maximum equilibrium power levels possible under natural circulation only.

Energy Technology Data Exchange (ETDEWEB)

A passive integrating radon dosemeter is described. The radon dosemeter is based on radon adsorption on activated charcoal. By placing TLD crystals inside an open charcoal container, the beta radiation from radon daughters, produced by the decay of adsorbed radon, is detected continuously during the exposure time. After closing the container, radiation will still be detected by the TLD crystal. Calibration procedures are reported and the suitability of the dosemeter is discussed. The dosemeter proved to be suitable for measurements during periods from a few days to two weeks both in domestic and mine atmospheres.

CERN Document Server

We report on the design, fabrication and testing of two superconducting passive microwave components, a quadrature hybrid and a 20 dB directional coupler. These components are designed to be integrated with superconducting qubits or Josephson parametric amplifiers and used in quantum information processing applications. For the coupler, we measure return loss and isolation > 20 dB, and insertion loss 20 dB and insertion loss < 0.3 dB in a 10% band around 6.5 GHz. These values are within the design specifications of our application; however, we find a 7% difference between the designed and measured center frequency for the hybrid.

International Nuclear Information System (INIS)

Heat transfer augmentation has developed into a major specialty area in heat transfer research and development. A bibliography of world literature on augmentation is presented. The literature is classified into passive augmentation techniques, which require no external power, and active techniques, which do require external power. The fourteen techniques are grouped in terms of their application to the various modes of heat transfer. Mass transfer is included for completeness. Key words are included with each citation for technique/mode identification. The total number of publications cited is 1,967, including 75 surveys of various techniques and 42 papers on performance evaluation of passive techniques. Patents are not included as they will be the subject of a future topical report.

Energy Technology Data Exchange (ETDEWEB)

Cyclic voltammograms of SUS 304 stainless steel in various neutral solutions such as Na/sub 2/SO/sub 4/ at high temperature were measured, as a successive study to previous report in which effects of temperature and pH on polarization behavior of stainless steel were studied. In this measurement Ag/AgCl reference electrode and platinum counter electrode were used in a static autoclave lined with inconel. Passive films formed in various conditions were analysed by electron diffraction and Auger spectroscopy. Results obtained were compared with anodic behavior of iron, chromium and nickel and with thermodynamical stabilities of their compounds. The main results are summarized as follows. (1) Stainless steel shows such electrochemical behavior as active dissolution, passivation and transpassivation in a deaerated neutral solution at 250/sup 0/C after fully reductive treatment of the specimen. In air-saturated solution, the peak of active ...

Energy Technology Data Exchange (ETDEWEB)

The potentiodynamic polarization measurement of 254SMO stainless steel (UNS 31254) was conducted in 3.5% NaCl solutions with pH ranging from 0.1 to 5. The results indicated that this stainless steel offered excellent pitting corrosion resistance in corrosive environments. Further, it also exhibited various features on the polarization curves in different pH solutions. The electrochemical constant-potential passivation treatment performed at different pH followed by XPS analysis revealed that the primary constituents of the outermost layer of the passive films formed in the weak (pH 5) and strong (pH 0.8) acid solutions are iron oxides and Cr{sub 2}O{sub 3} and Cr(OH){sub 3}, respectively. Molybdenum oxides, primarily in the six-valence state, existed in the outermost layer of the passive film. Only very weak signals corresponding to that of nickel oxides were detected in the film formed in the weak acid (pH 5) solution. The ...

Energy Technology Data Exchange (ETDEWEB)

Alloy 600 is commonly used in the primary systems of PWR plants because of its excellent resistance to a stress corrosion cracking and pitting. But a stress corrosion cracking and pitting corrosion are occasionally observed under PWR conditions, which may be correlated with the passive film on the Alloy 600 surface. There is little information on the composition of films growing on the surface of Alloy 600 at high temperature. Therefore, an understanding of the basic electrochemical behaviors about an anodic dissolution and the passivation of the bare surface of metals and alloys provides important information about localized corrosions like a SCC and pitting. Oxide on the steel surfaces in an aqueous solution above 100 .deg. C is composed of a duplex film structure. The inner layer of the oxide is dense and less porous, which is formed by a growth of the oxide layer on the metal surface. Outer layer of the oxide is less adhesive, which is ...

Energy Technology Data Exchange (ETDEWEB)

The five thermal-hydraulic concepts chosen for conceptual study of advanced PWR systems have been studied as follows: (1) Critical Heat Flux in passive PWR Conditions: review of previous works (various of correlations, analysis of parametric trends) on CHF, assessment and improvement of CHF prediction models for round tubes, development of the prediction model on bundle CHF with considering the correction factor calculated from the tube data base, design and construction of the intermediate-pressure CHF experimental loop, extension of CHF data base by performing the experiments at low-flow, and low-quality conditions (2) Passive Cooling Concepts for Concrete Containment Systems: Selection of the external condenser by comparing and reviewing between passive cooling concepts for concrete containment system concepts, survey and review of previous studies (theoretical mechanism of condensation heat transfer and effect of ...

Energy Technology Data Exchange (ETDEWEB)

The meeting was arranged into the following sessions: introductory; advanced ceramics and ceramic composites; ceramic and metal matrix composites; electronic materials and devices; acoustoelasticity, stress, and texture; composites-porosity, strength, and UT propagation; process modeling and monitoring; thermal wave physics; material properties, composites, surfaces, and interfaces; acoustic emission; ferromagnetic materials; new sensors; NDE reliability assessment; elastic wave scattering and propagation; image analysis, data storage, and signal processing; UT transducers; weldments and bonded materials; eddy current models; unified life cycle engineering; x rays, CT, and NMR; eddy current probes and instruments; acoustic microscopy imaging, and reconstruction; signal processing, measurement techniques, and systems; NDE applications of artificial intelligence; crack behavior influenced by history; inversion procedures for UT and EC; process ...

Energy Technology Data Exchange (ETDEWEB)

The Versatile Toroidal Facility (VTF) is a large laboratory plasma machine of 1 meter major radius used to carry out investigations of ionospheric plasma turbulence. Spectral analysis has been performed on plasmas produced by the electron emitters. Interest has focused on the low frequencies below the lower hybrid resonance where ion acoustic and current-convective modes have been observed. Microwaves injected from a 3,000 watt magnetron produce dramatic changes to the low frequency spectrum. First, the parametric decay instability intensifies the ion acoustic modes in the region of plasma heated by the microwaves. Second, the normally dominant current-convective modes are greatly suppressed in the heated region due to the oscillating electric field of the pump wave. When the authors probe beyond the heated region, these two pump wave effects are no longer observed, presumably because the microwaves are denied access to beyond the heated region ...

Energy Technology Data Exchange (ETDEWEB)

A 19.1 metre wind turbine blade was subjected to static tests. The purpose of the test series was to verify the abilities of different types of sensors to detect damage in wind turbine blades. Prior to each of the static test-series an artificial damage was made on the blade. The damage made for each test-series was surveyed during each series by acoustic emission, fiber optic micro bend displacement transducers and strain gauges. The propagation of the damage was determined by use of ultra sonic and X-ray surveillance during stops in the test series. By use of acoustic emission it was possible to measure damage propagation before the propagation was of visible size. By use of fiber optic micro bend displacement transducers and strain gauges it was possible to measure minor damage propagation. By use of both ultra sonic, and X-ray NDT-equipment it were possible to determine the size of propagated damage. (au)

Energy Technology Data Exchange (ETDEWEB)

'The primary objective of this research project is to acquire a deeper fundamental knowledge of acoustic cavitation and cavitation chemistry, and in doing so, to ascertain how ultrasonic irradiation can be more effectively applied to environmental problems. Four on-going projects will be described in this progress report, The first project is the destruction of carbofuran in a Near-Field Acoustical Processor (NAP), and the hydrodynamic characterization of the reactor. The second project is a comprehensive study of how ultrasonic frequency influences sonochemical reaction rates; the substrate it, the preliminary portion of this study has been hydrogen peroxide formation. The third project in progress is destruction of four polychlorinated biphenyls at 20 kHz. Work so far has been at 20 kHz, but the most significant portion of this project will involve a multi-frequency (ultrasonic frequency) study. Finally, the destruction of a ...

International Nuclear Information System (INIS)

We give a theoretical design for a locally resonant two-dimensional cylindrical structure involving a pair of C-shaped voids in an elastic medium which we term as double 'C' resonators (DCRs) and imbedded thin stiff bars, that displays the negative refraction effect in the low frequency regime. DCRs are responsible for a low frequency band gap which hybridizes with a tiny gap associated with the presence of the thin bars. Using an asymptotic analysis, typical working frequencies are given in closed form: DCRs behave as Helmholtz resonators modeled by masses connected to clamped walls by springs on either side, while thin bars behave as a periodic bi-atomic chain of masses connected by springs. The discrete models give an accurate description of the location and width of the stop band in the case of the DCR and the first two dispersion bands for the periodic thin bars. We then combine our asymptotic formulae for arrays of DCR and thin-bars to design a composite structure that displays a ...