Reactive power plays an important role in supporting the real power transfer by maintaining voltage stability and system reliability. It is a critical element for a transmission operator to ensure the reliability of an electric system while minimizing the cost associated with it. The traditional objectives of reactive power dispatch are focused on the technical side of reactive support such as minimization of transmission losses. Reactive power cost compensation to a generator is based on the incurred cost of its reactive power contribution less the cost of its obligation to support the active power delivery. In this paper an efficient Particle Swarm Optimization (PSO) based reactive power optimization approach is presented. The optimal reactive power dispatch problem is a nonlinear optimization problem with several constraints. The objective of the proposed PSO is to minimize the total ...
The obligations of organisations associated with policy formation and implementation of international mass public health programmes are explored. Lines of responsibility are considered to become unclear...Full Text Available
Once the definition of the CHP (combined heat and power generation) certificate is clear, demand for it can be organised in several ways. A well-designed system of mandatory demand, by means of an obligation to acquire a certain amount of CHP certificates each year, is effective to meet the policy target. The voluntary willingness to pay for CHP certificates is likely to be small, resulting in a very thin market. Finally, instead of creating a demand solely targeted at the CHP certificates, demand could also result from interacting policy schemes such as emissions trading. Assuming that a CHP certificate scheme is going to be introduced, we would recommend to issue standard CHP certificates based on additional ('fuel-free') kWh output (substitution approach with standard certificates) and create demand by means of an incentive on electricity supply companies to purchase CHP certificates. The incentive could either be quantitative (an ...
The obligate biotrophic fungus Golovinomyces orontii causes powdery mildew (PM) disease on its host Arabidopsis thaliana. Most research on the G. orontii?Arabidopsis pathosystem uses rosette leaves as experimental materials, so little is known about the behavior of G. orontii on other Arabidopsis organs. We thus conducted microscopic analyses of the PM infection process on leaves, stems, fruits and roots of Arabidopsis. Adaxial and abaxial surfaces of mature rosette leaves supported G. orontii infection, but growth was somewhat suppressed on cauline leaves. Prepenetration processes (germination and appressorium formation) were strongly inhibited on stems, fruits and roots. To test the effect of alterations in the Arabidopsis cuticle on the inhibition of prepenetration processes on stems, w...
This article reports on the operation of Fibrowatt's third chicken waste-fuelled power plant at Thetford in Norfolk, UK. Details are given of the plant which started operation in October 1998, the chicken litter fuel, the spiral screw fuel feeders, the Detroit Stoker grate and spreader stokers which ensure the fuel is burnt mid-air, the production of fertiliser from the ash, and fluegas emission control using cyclones, a baghouse and lime addition to neutralise acid gas. The economics of the project, and the support for the renewable electricity generation under the UK government's Non-Fossil Fuel Obligation are discussed. A site plan of the Thetford plant and a flow diagram of the process are provided.
The new Code Case to substitute the allowable crack angle for a circumferential surface crack in 'Rules on Fitness-for-Service (FFS)' published from The Japan Society of Mechanical Engineers (JSME). Until now, the angle of a circumferential surface crack was limited below 60deg. This is the limitation with consideration to the stability of the crack if the deep crack penetrates wall of the pipe. Therefore, a long crack (such like an SCC) was obliged to repair or replace even if it was shallow enough. Weld Overlay (WOL) repair in which strength of the original piping is ignored is also inapplicable for the same reason. In order to solve this irrationality, the new Code Case applying to the crack stability assessment when the crack angle exceeds 60deg was established, and allowable crack depth according to the crack angle were defined in it. (author)
The obligations under international law to reduce transfrontier air pollution is discussed in five chapters from various aspects. Consequences for the European Communities are gone into in five further chapters. (orig./HP)
... Implied terms are all of your rights and obligations that come directly from the law. Express terms are rules and charges the park owner decides to put in your agreement. Even if you do not have a written statement, you still have all the rights the law gives you. These rights come from the Mobile Homes Act of 1983. Your rights and obligations from the law ...
fuel obligation under the RFS2 program for the production or importation of conventional jet fuel, RINs can be generated for renewable jet fuel. Is that right? A: As described in...
Rotifers of class Bdelloidea are common invertebrate animals with highly unusual characteristics, including apparently obligate asexuality, the ability to resume reproduction after desiccation at any...Full Text Available
The guiding mechanism is attached by a hinge (swivel) to the supporting frame, and the frame is equipped by hinges (swivels) with hydraulic or pneumatic cylinders mounted on its ends and is attached by hinges (swivels) to the coke ejector and guide respectively. This increases the productivity and efficiency of operating the system.
The U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) administers and operates the Waste Isolation Pilot Plant (WIPP) site, which hosts a deep geologic repository for safe disposal of U.S. defense-related TRU waste and is located 42 kilometers (km) east of Carlsbad, New Mexico. CBFO also manages the National Transuranic Waste Program (NTP), which oversees TRU waste management from generation to disposal. The WIPP began receiving waste in March 1999. In some areas of broad international interest, the CBFO has developed a leading expertise through its 25-year WIPP repository and TRU waste characterization activities. In addition to participating in relevant and beneficial experiments, the CBFO will provide the international community convenient access to this information by sponsoring and hosting symposia and workshops on relevant topics and by participation in international waste management organizations and topical meetings. In recognition of the successes at WIPP, the Inter ...
An actuating mechanism of a mine combine is proposed. It includes a rotating platform in a vertical plane on which by hinges with the possibility of rotation parallel to the plane of the platform there are handles with cutting drums and a mechanism for extension of the handle which has hydraulic cylinders. With a decrease in load on the hinges of the handles from bending forces, on the platform between the front edge of the platform and the site of attachment of the handle hinges there are openings. Each handle has a support projection which is placed in this opening with the possibility of movement. A clamp plank is installed on it which covers the opening. The distance from the center of the projection support to the axis of the corresponding hinge is greater than the height of embedding of this hinge into the platform.
A device is described for transporting loads, especially for moving belt driving stations in open pit mining operations with a propelling mechanism which for lifting a respective load is operable to move into a free space formed by the load with the ground. The device comprises a plurality of lifting mechanisms, by means of which, a lifting platform can be brought into engagement with a supporting surface of the load. The device comprises at least one supporting member which is so designed that it prevents the lifting platform from lifting off lifting mechanisms. Furthermore, means are provided which permit a turning of the lifting platform relative to the lifting mechanisms about a vertical axis which is arranged in a certain relationship to the propelling mechanism.
Papers are presented under the following topics: machine control and automation; rock drilling; cutting and fragmentation; rock characterization, remote sensing and interface detection; artificial intelligence and mine monitoring systems; computer applications; mechanical excavators; material handling; surface and underground mining; innovative mining systems; new developments in mechanical miners; ground hazard detection and control; ground support; and extraterrestrial mining.
Papers are presented under the session headings: research in mechanical fragmentation; rock characterization, remote sensing and interface detection; monitoring, data transmission and communications; tunnel boring machines; minewide monitoring and expert systems for ground control; machine guidance; shaft and raise boring; automation of drilling equipment; machine automation and control; new developments in mechanical miners; materials handling; innovative mining systems; general minewide monitoring and expert systems; ground support; human factors; and extraterrestrial mining.
AbstractIndividual informed consent is a key ethical obligation for clinical studies, but empirical studies show that key requirements are often not met. Common recommendations to strengthen...Full Text Available
Glacier ice worms, Mesenchytraeus solifugus and related species, are the largest glacially obligate metazoans. As one component of cold temperature adaptation, ice worms maintain atypically...Full Text Available
Most physicians dealing with Jehovah's Witnesses (JWs) who refuse blood-based treatment are uncertain as to any obligation to educate patients where it concerns the JW blood doctrine itself. They often...Full Text Available
Arbuscular mycorrhizal fungi (AMF) are obligate biotrophs, known to play an important role in ecological processes. Conventional light microscopy is the most common method used to detect their presence...Full Text Available
Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to investigation of alternative support designs and materials. In recent designs of steam generators the carbon steel drilled hole tube support plate has been replaced by one of quatrefoil or trefoil shape to minimize the contact area. These plates are now made of more corrosion resistant chromium steel (approx. 12%Cr) to ensure that they are less vulnerable to attack in the event of adverse boiler water chemistry. This study was initiated to examine the corrosion behavior of a range of chromium steels in the acid chloride environments characteristic of tube/support plate crevices under adverse boiler water conditions. Objectives of the study were to: 1) determine the relative susceptibility of candidate tube support plate steels to acid chloride corrosion; ...
Barsebaeck 1 was closed on 30 November 1999. Barsebaeck's output of approximately 4 TWh per year will primarily be replaced by imports from coal-fired plants in Denmark and Germany. During the year, the closure of Swedish fossil-fired condensing power stations continued. With that, over 3,000 MW of peak-load power has been shut down during recent years. Consequently, situations entailing shortages of power can arise. On the deregulated electricity market, it is only the system operators that have a satisfactory overview of the overall electricity balance. The Swedish Power Association has thus lobbied the government as regards the need to elucidate Svenska Kraftnaet's responsibility. In a governmental decision from December, Svenska Kraftnaet was given the task of, among other things, monitoring the available capacity during peak loads and developing market instruments that can contribute to safeguarding the availability of power during peak loads. Svenska Kraftnaet ...
A public health emergency such as an influenza pandemic will lead to shortages of mechanical ventilators, critical care beds, and other potentially life saving treatments. This will raise difficult...Full Text Available
The cancer preventive action of (−)-epigallocatechin gallate (EGCG), found in green tea, is strongly supported by epidemiology and laboratory research data. However, the mechanism by...Full Text Available
Previous ultrasound elasticity imaging experiments supported a generally accepted concept that the hardness of deep venous thrombi increases with thrombus aging. Results also showed that this...Full Text Available
Different tombusviruses were able to support the replication of either homologous or heterologous defective interfering (DI) RNAs, and those infected plants usually developed typical attenuated symptoms....Full Text Available
Rapid corrosion of PWR steam generator carbon steel support structures and consequential denting of steam generator tubes led to considerable investigation of the mechanism of corrosion and for palliatives. The basic mechanism is now fairly well understood. Chloride present in the boiler feedwater from condenser leakage is concentrated in the support plate crevice as a result of the superheat present. This leads to the formation of a low pH acid ferrous chloride environment either through the hydrolysis of a weak base chloride such as MgCl_2 or the combined action of a neutral chloride with an oxidizing agent. Rapid attack of the carbon steel ensues with the Fe_3O_4 corrosion product forming at the metal/oxide interface. This oxide has a volume approximately twice that of the steel consumed and thus eventually fills the crevice between the tube and the support plate. Oxide growth ...
Biological membranes are lamellar structures composed of two leaflets capable of supporting different mechanical stresses. Stress differences between leaflets were generated during micromechanical experiments...Full Text Available
This document is an executive summary of the colloquium organized by the French syndicate of renewable energies (SER) which took place at the Maison de l'UNESCO in Paris during the national debate on energies organized by the French government in spring 2003. The colloquium was organized around 6 round tables dealing with: the world perspectives and the environmental context of the contribution of renewable energies to the sustainable development (respect of Kyoto protocol commitments, contribution to the security of energy supplies, lack of large scale program of development of decentralized power generation in developing countries, lack of market tools linked with CO{sub 2} emissions, improvement of competitiveness); development of renewable energies in Europe (promotion and sustain in all European countries, obligation of supply and purchase, pricing regulation, European harmonization of practices); renewable electricity and its place in the new ...
The next great issue on the Russian landscape will be management of its foreign debt. In the near future the United States will be called upon to lead an international program of debt restructuring to assist Russia in overcoming the burden of its debt trap. With debt service obligations equal to 50{percent} of 1999 revenues, Russia has virtually no chance of sustaining a program of economic recovery without debt relief (Hardt, 1999). With some form of debt restructuring a foregone conclusion, Russia, the United States, and world community have a vital stake in searching for creative ways to transform the inevitability of debt restructuring into something of value and constructive to Russia and the problems it faces. This was the rationale behind debt-for-nature swaps which emerged in the early 1980s in Latin American and Eastern Europe as a means of relieving developing nations of their crippling foreign debt. Debt-for-nature swaps served both domestic and ...
The problem of denting in steam generators leads to change in the conception of the tube support plates. A new material is now used for this component, a 13% Cr steel, which composition has been adjusted for weldability and mechanical resistance criteria. The geometry of trefoil support plate (TSP) has also been improved, using a broached TSP (quadrifoiled holes) instead of a drilled TSP. Tests have been performed on 13% Cr and C-steel broached TSP, and drilled TSP, to confirm the better resistance to denting of this new configuration.
Recently, Faria et al. [Phys. Lett. A 305 (2002) 322] discussed an example in which the Heisenberg and the Schroedinger pictures of quantum mechanics gave different results. We identify the mistake in their reasoning and conclude that the example they discussed does not support the inequivalence of these two pictures.
The mechanisms underlying life machinery are still not completely understood. Something is known, something is ?probably? known, other things are still unknown. Scientists all over the world are working very hard to clarify the processes regulating the cell life cycle and bioinformaticians try to support them by developing specialized automated tools. Within the plethora of applications devoted to the study of life mechanisms, tools for the analysis and comparison of biological networks are catching the attention of many researchers. It is interesting to investigate why.
Due to legal restrictions, the German hard coal mining company Deutsche Steinkohle AG (DSK) is obliged to conduct a monitoring on surface changes (subsidence) caused by mining activity (e.g. topographic surface, groundwater, water, flora and fauna, soil). To fulfill legal demands and to do this effectively, process chains by use of Photogrammetry, Remote Sensing and Geo-Informationssystems (GIS) have been established. Photogrammetric methods are used to generate high resolution Digital Elevation Models (DEM) from which in combination with subsidence data geometrical changes at the topographic surface are deduced. The potential use of active sensors (Laser Scanning and Synthetic Aperture Radar Systems) to deduct DEM has been investigated. The applicability of SAR satellite data to detect and observe subsidence and resulting movements - point wise or with spatial extent - using differential SAR Interferometry (dInSAR) as well as persistent scatterer technology (here: ...
The 'high-tension distribution line design support system' was developed for the 'work design support system'. This support system is composed of the work outline editor for preparing work details and facility data and the inference engine for preparing practical design plans, and can check system conditions such as voltage drop and deviation from technical standards automatically. The work outline editor takes charge of selection of work items, selective input of system information, and setting of some conditions such as pole position and reserved load onto a system diagram. The inference engine provides the design plan automatically based on the information inputted by the editor. For the design of high-tension distribution line, such various factors as local condition and load sharing of distribution systems should be considered. This design support system attains ...
Detailed chemical kinetic reaction mechanisms have been developed to describe the pyrolysis and oxidation of the n-alkanes, including n-octane (n-C{sub 8}H{sub 18}), n-nonane (n-C{sub 9}H{sub 20}), n-decane (n-C{sub 10}H{sub 22}), n-undecane (n-C{sub 11}H{sub 24}), n-dodecane (n-C{sub 12}H{sub 26}), n-tridecane (n-C{sub 13}H{sub 28}), n-tetradecane (n-C{sub 14}H{sub 30}), n-pentadecane (n-C{sub 15}H{sub 32}), and n-hexadecane (n-C{sub 16}H{sub 34}). These mechanisms include both high temperature and low temperature reaction pathways. The mechanisms are based on previous mechanisms for n-heptane, using the same reaction class mechanism construction developed initially for n-heptane. Individual reaction class rules are as simple as possible in order to focus on the parallelism between all of the n-alkane fuels included in the mechanisms, and there is an intent to ...
Detailed chemical kinetic reaction mechanisms have been developed to describe the pyrolysis and oxidation of nine n-alkanes larger than n-heptane, including n-octane (n-C{sub 8}H{sub 18}), n-nonane (n-C{sub 9}H{sub 20}), n-decane (n-C{sub 10}H{sub 22}), n-undecane (n-C{sub 11}H{sub 24}), n-dodecane (n-C{sub 12}H{sub 26}), n-tridecane (n-C{sub 13}H{sub 28}), n-tetradecane (n-C{sub 14}H{sub 30}), n-pentadecane (n-C{sub 15}H{sub 32}), and n-hexadecane (n-C{sub 16}H{sub 34}). These mechanisms include both high temperature and low temperature reaction pathways. The mechanisms are based on our previous mechanisms for the primary reference fuels n-heptane and iso-octane, using the reaction class mechanism construction first developed for n-heptane. Individual reaction class rules are as simple as possible in order to focus on the parallelism between all of the n-alkane fuels included in ...
British Columbia Hydro's new corporate strategic plan now recognizes two special responsibilities: to the province's native peoples and to the people of the Columbia River Basin. Eight strategic initiatives in the categories of obligations, investments, and opportunities are outlined. Four initiatives are aimed at meeting moral obligations: to pursue employment equity, to establish mutually beneficial business relationships with native peoples, to develop and maintain a leadership role in environmental stewardship, and to ensure a fair annual return on investment to the province. Two initiatives will see investments of strategic importance to British Columbia's future in the areas of job creation and economic progress throughout the province, notably in the Columbia River Basin. The final two initiatives concern development of export markets for the utility's technical services and expertise, and synergy with ...
Equivalent circuit and electrical parameters for H-doped NH_4UO_2PO_4.3H_2O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).
The objectives of the project were to develop operational techniques for promoting contaminant hideout return from tube support crevices and to identify the effect of chemical inhibitor application on corrodent transport. The implementation of routine procedures for promoting the return of sequestered corrodents could retard the progression of denting or other corrosion processes and improve steam generator availability. Tests also quantified the effect of inhibitor application on crevice hideout and hideout return processes, with the intention of developing a better understanding of the inhibition mechanism. By carefully monitoring the hideout and hideout return inventories, the program also has provided the opportunity to study steam generator concentration processes in general.
A variety of engineering and experimental applications require primary support structures which are self-centering. High mechanical strength, low-density, carbon fiber/epoxy matrix composite springs are used in unique planar, cylindrical, conical, and spherical configurations to self-center components. The sinusoidal and triangular-shaped composite springs are readily manufactured and assembled into component hardware. Design considerations, flexural strength properties, load bearing and centering data plus procedures for the manufacture of composite springs are presented.
At atmospheric pressure and room temperature, dielectric barrier discharge induced plasma oxidation for achieving supported TiO2 photocatalysts derived from TiCl4 adsorbed onto ?-Al2O3 pellets was studied. The supported TiO2/?-Al2O3photocatalysts prepared by a cyclic 'adsorption-discharge' approach, without requirement of heat treatment, exhibit high activity in the photocatalytic degradation reaction of formaldehyde. The mass spectra and optical emission spectra during O2/Ar discharge for oxidizing the adsorbed-state TiCl4 were measured. The mechanism for the TiO2 formation from adsorbed-state TiCl4 by plasma oxidation was discussed.
In spite of recent education reform and reorganization efforts requiring the use of research-based methods, the fundamental elements of an effective program for children and youth with emotional and behavioral disorders (EBD) have not been succinctly identified. This article presents the essential features of programs for students with EBD. Program elements include (a) qualified and committed professionals, (b) utilitarian environmental supports, (c) effective behavior management plans, (d) valid social skill and social interpretation training and social interaction programs, (e) proven academic support systems, (f) strong parent- and family-involvement programs, (g) coordinated community supportmechanisms, and (h) ongoing evaluation of essential program components and student outcomes and progress. A justification for the program and a comparison of the proposed program with existing models is ...
Megasphaera elsdenii is a lactate-fermenting, obligately anaerobic bacterium commonly present in the gastrointestinal tracts of mammals, including humans. Swine M. elsdenii strains were previously shown to have high levels of tetracycline resistance (MIC = 64->256 micro g/ml) and to carry mosaic (re...
This Insight conference was held to review many of the legal aspects, legislation and regulations dealing with abandoned wells within the petroleum and natural gas industry. Remedial actions to rehabilitate the abandoned sites, legal issues in abandonment, obligations of the owner, the industry-sponsored Orphans Wells Program, were some of the topics discussed.
In this paper, we intend to formulate a new metaheuristic algorithm, called Cuckoo Search (CS), for solving optimization problems. This algorithm is based on the obligate brood parasitic behaviour of some cuckoo species in combination with the Levy flight behaviour of some birds and fruit flies. We validate the proposed algorithm against test functions and then compare its performance with those of genetic algorithms and particle swarm optimization. Finally, we discuss the implication of the results and suggestion for further research.
Hyperosmotic stress is known to significantly enhance net uptake of inorganic ions into plant cells. Direct evidence for cell turgor recovery via such a mechanism, however, is still lacking. In the...Full Text Available
Surface deposition probe techniques have been shown to be an effective means of determining the characteristics of the plasma edge region of magnetic confinement devices. Experimental results on ISX-B and EBT-S have led to a consistent picture of the edge plasma and the dominant impurity introduction mechanisms. This picture is supported by numerous other measurements and emphasizes the importance of concentrating several techniques on the complex problems of plasma fusion.
This paper shows some considerations about the cost of wood, steel and cement support pillars in rural power distribution systems. The life span, mechanical properties, cost estimation and general durability of each type of pillar was evaluated, aiming a better selection of the desired one. 6 figs., 8 tabs., 4 refs.
In order to better understand the molecular mechanisms of human hair growth control and to test hair growth-modulatory drugs, appropriate in vitro models are required. Here, we report the long-term...Full Text Available
The device for removing drilling fines from the well head includes a support disk encompassing the sucker rod of the drilling machine with frame made in the form of a dish with inner conical surface, and overturned truncated cone located in the dish of the support disk with the formation between them of a ring guide slit. In order to improve the effectiveness of removing the drilling fines and convenience of operation by excluding heavy manual auxiliary operations to clean the well head and to move the device from one well to another, it is equipped with a mechanism for suspension with a drive. The inner conical surface of the dish is equipped with slide blocks, while the overturned truncated cone is equipped with projections. The suspension mechanism is made in the form of a hydrocylinder and two pairs of levers connected in pairs by means of hinges. The hinges of each pair of levers are connected to ...
Biosorption of elements is a little understood phenomenon exhibited by some types of even nonliving microbial biomass. A common fungus Rhizopus arrhizus has been reportd to take up uranium from adqueous solutions to the extent of 180 mg U/sup 6 +//g. The mechanism of uranium sequestering by this type of biomass was studied by using experimental techniques such as electron microscopy, x-ray energy dispersion analysis, IR spectroscopy, and supporting evidence was obtained for a biosorption mechanism consisting of at least three processes. Uranium coordination and adsorption in the cell-wall chitin structure occur simultaneously and rapidly whereas precipitation of uranylhdroxide within the chitin microcrystalline cell-wall structure takes place at a lower rate. Interference of Fe/sup 2/ and Zn/sup 2 +/ coions with uranium biosorption is indicated.
Studies at Commissariat a l'Energie Atomique (CEA) have been under way for three years in an attempt to find methods for preventing and stopping denting. Tests have been performed in 28 model boilers (Ajax with U tubes and Clarinette with straight tubes). In these boilers, with continous injection and blowdown, and heat flux is about 40 W X cm"-"2 (126900 Btu/ft"2 X h). The kinetics of denting has been studied with different levels of faulting. Some high-temperature electrochemical measurements established the mechanism of denting in the boiler tests. Denting kinetics can be rationalized in terms of three main parameters: faulting level, heat flux, and relative mechanical strength of the tube compared to the support plate.
Tube supports used in the tube bundles of PWR steam generators have consisted of mechanical devices located at intervals along the tube bundle. The presence of tube supports creates regions of restricted flow with altered flow patterns and increased pressure drop. An additional and very important effect is also the possibility of local complete vaporization or dryout occurring in the tube/support flow passage and crevices. The thermal/hydraulic conditions at which dryout occurs are of particular interest because of the possibility of the deposition of dissolved solids with the occurrence of dryout. As long term build-up of solid deposition could have a deleterious effect, knowledge of the conditions at which dryout occurs would possibly provide a means to avoid this build-up. A test program, sponsored by the Steam Generator Project Office of the Electric Power Research Institute, was conducted to ...
Current light water reactor (LWR) steam generators have been affected by a variety of corrosion and mechanical damage degradation mechanisms. Included are wear caused by tube vibration, intergranular corrosion, pitting, and thinning or wastage of the steam generator tubing and accelerated corrosion of carbon steel supports (denting). The Electric Power Research Institute (EPRI) and the Steam Generator Owners Groups (I, II) have sponsored laboratory and field studies to provide ameliorative actions for the majority of the damage forms experienced to date. Some of the current corrosion mechanisms are aggravated or caused by unique materials choices or materials interactions. New materials have been proposed and at least partially qualified for use in replacement model steam generators, including an advanced LWR design. In so far as possible, the materials choices for the advanced LWR steam generator avoid ...
A micro-mechanistic understanding of bone fracture that encompasses how cracks interact with the underlying microstructure and defines their local failure mode is lacking, despite extensive research on the response of bone to a variety of factors like aging, loading, and/or disease. Micro-mechanical models for fracture incorporating such local failure criteria have been widely developed for metallic and ceramic materials systems; however, few such deliberations have been undertaken for the fracture of bone. In fact, although the fracture event in mineralized tissues such as bone is commonly believed to be locally strain controlled, until recently there has been little experimental evidence to support this widely held belief. In the present study, a series of in vitro experiments involving a double-notch bend test geometry are performed in order to shed further light on the nature of the local cracking events that precede catastrophic fracture ...
In order to improve the reliability of PWR steam generators, we have performed research to improve the tubing material and tube-support-plate configuration, based on our wide operating experience, and have developed and verified Alloy TT690 as the optimum tubing material and the BEC (Broached Egg Crate) type tube-support design. In the research, we have studied the metallurgical mechanism of the alloy to improve its corrosion resistance, evaluated corrosion susceptible region quantitatively, estimated the actual environment in a steam generator and confirmed the reliability by a model boiler test over a long period. It has been verified that the steam generator with the latest design has higher reliability with respect to the corrosion resistance of tubes. (author).
In August 1995, the US Nuclear Regulatory Commission (NRC) issued a policy statement proposing improved regulatory decision making by increasing the use of probabilistic risk assessment (PRA) in all regulatory matters to the extent supported by the state-of-the-art in PRA methods and data. A key aspect in using PRA in risk-informed regulatory activities is establishing the appropriate scope and attributes of the PRA. In this regard, the American Society of Mechanical Engineers (ASME) decided to develop a consensus PRA standard. The objective is to develop a PRA standard such that the technical quality of nuclear plant PRAs will be sufficient to support risk-informed regulatory applications. The authors present example recommendations for the systems analysis element of a PRA for incorporation into the ASME PRA standard.
Equivalent circuit and electrical parameters for H-doped NH{sub 4}UO{sub 2}PO{sub 4}.3H{sub 2}O self supported membranes have been determined by impedance spectroscopy. The measurements were carried out with a dry membrane, at different temperatures, and a wet membrane in contact with different electrolyte solutions. Resistance values for the dry membrane decrease with temperature increase, which agrees with the weak protonic character of the H-doped ammonium uranylphosphate. On the other hand, differences in the electrical parameters, depending on the electrolyte considered were also obtained and are attributed to different conduction mechanisms. (Author).
At present, the mostly used and developed mechanism is hardware virtualization which provides a common platform to run multiple operating systems and applications in independent partitions. More precisely, it is all about resource virtualization as the term hardware virtualization is emphasized. In this paper, the aim is to find out the advantages and limitations of current virtualization techniques, analyze their cost and performance and also depict which forthcoming hardware virtualization techniques will able to provide efficient solutions for multiprocessor operating systems. This is done by making a methodical literature survey and statistical analysis of the benchmark reports provided by SPEC (Standard Performance Evaluation Corporation) and TPC (Transaction processing Performance Council). Finally, this paper presents the current aspects of hardware virtualization which will help the IT managers of the large organizations to take effective decision while ...
This article examines the potential threat of marine pollution caused by offshore oil and gas development activities in the disputed areas of the South China Sea (SCS) and the Spratly Islands. After addressing the potential threat of marine pollution, it discusses the legal obligations and political commitment of the SCS littoral states regarding the protection of the marine environment in the area. The role that Taiwan can play in these matters is also examined.
Three possibilities to observe the Higgs-top interaction at future {gamma}{gamma}-colliders are discussed: (a) associated Higss production via the {gamma}{gamma}{yields}tanti tH reaction, (b) Higgs obliged radiative correction to the {gamma}{gamma}{yields}tanti t channel, (c) Higgs resonance production via {gamma}{gamma}{yields}H{yields}ZZ. The results obtained show windows of the Higss mass where the Yukawa interaction of the Higss with the top quark can be studied at {gamma}{gamma}-colliders. (orig.).
Three possibilities to observe the Higgs-top interaction at future #gamma##gamma#-colliders are discussed: a) associated Higss production via the #gamma##gamma##->#tanti tH reaction, b) Higgs obliged radiative correction to the #gamma##gamma##->#tanti t channel, c) Higgs resonance production via #gamma##gamma##->#H#->#ZZ. The results obtained show windows of the Higss mass where the Yukawa interaction of the Higss with the top quark can be studied at #gamma##gamma#-colliders. (orig.).
Unlike the well-characterized nuclear function of the Notch intracellular domain, it has been difficult to identify a nuclear role for the ligands of Notch. Here we provide evidence for the nuclear function of the Notch ligand Delta-like 1 in colon cancer (CC) cells exposed to butyrate. We demonstrate that the intracellular domain of Delta-like 1 (Dll1icd) augments the activity of Wnt signaling-dependent reporters and that of the promoter of the connective tissue growth factor (CTGF) gene. Data suggest that Dll1icd upregulates CTGF promoter activity through both direct and indirect mechanisms. The direct mechanism is supported by co-immunoprecipitation of endogenous Smad2/3 proteins and Dll1 and by chromatin immunoprecipitation analyses that revealed the occupancy of Dll1icd on CTGF promot...
The similarity in the genetic regulation of arthropod and vertebrate appendage formation has been interpreted as the product of a plesiomorphic gene network that was primitively involved in bilaterian appendage development and co-opted to build appendages (in modern phyla) that are not historically related as structures. Data from lophotrochozoans are needed to clarify the pervasiveness of plesiomorphic appendage-forming mechanisms. We assayed the expression of three arthropod and vertebrate limb gene orthologs, Distal-less (Dll), dachshund (dac), and optomotor blind (omb), in direct-developing juveniles of the polychaete Neanthes arenaceodentata. Parapodial Dll expression marks pre-morphogenetic notopodia and neuropodia, becoming restricted to the bases of notopodial cirri and to ventral ...
This work studied the effect of the nature of the metal on the performance of Co/CeO{sub 2}, Pd/CeO{sub 2} and Pt/CeO{sub 2} catalysts in the partial oxidation of ethanol. Infrared spectroscopy of adsorbed ethanol and temperature programmed desorption of ethanol were performed in order to establish the reaction mechanism. Catalytic experiments revealed that the product distribution is strongly affected by the nature of the metal. Acetaldehyde was practically the only product formed on a Co/CeO{sub 2} catalyst while methane was also produced on Pt/CeO{sub 2} and Pd/CeO{sub 2} catalysts. These results were explained through a reaction mechanism proposed by the characterization techniques. Co/CeO{sub 2} and Pt/CeO{sub 2} catalysts show mainly ethoxy species at room temperature whereas acetate species is mainly formed on the Pd/CeO{sub 2} catalyst. The ethoxy species can undergo further dehydrogenation and desorb as acetaldehyde. This effect is ...
The project has been developing Yttria Stabilized Zirconia (YSZ)-Alumina Composites as an electrolyte of a self-support type planar Solid Oxide Fuel Cell (SOFC) from the following points of view: a path of alumina particles with high thermal conductivity can be designed as an electrolyte sheet; there are some possibilities that the electrolyte can be enhanced in mechanical strength. As previously reported, these composite materials have higher mechanical strength and better thermal shock resistance than those of YSZ. These composites containing 0-30 wt% of Al[sub 2]O[sub 3] were measured by AC impedance method at temperatures of 250-1,000[degree]C. Electrical conductivities of 8YSZ without Al[sub 2]O[sub 3] and a composite consisting of 80 wt% YSZ and 20 wt%Al[sub 2]O[sub 3] as sintered samples were 1.2 x 10[sup -1]S/cm and 1.0 x 10[sup -1]S/cm respectively at 1,000[degree]C. The composite containing 20 wt% of Al[sub ...
In 1998 the American Society of Mechanical Engineers (ASME) formed the Committee on Nuclear Risk Management (CNRM) and a Project Team to develop a standard on PRAs for use in risk informed applications. This ASME standard is being developed to help provide an adequate level of quality in PRAs that are being used to support ASME initiatives to risk informed in-service inspection (ISI) and in-service testing (IST) of nuclear power plant components. A related need supported by the industry and the U.S. Nuclear Regulatory Commission is to reduce the level of effort that is being expended in pilot applications of risk informed initiatives to address questions about the sufficiency of quality in the supporting PRA models. The purpose of this paper is to discuss the authors' views on some of the technical issues that were encountered in the effort to develop the ASME PRA standard. Draft 12 of this ...
In 1998 the American Society of Mechanical Engineers (ASME) formed the Committee on Nuclear Risk Management (CNRM) and a Project Team to develop a standard on PRAs for use in risk informed applications. This ASME standard is being developed to help provide an adequate level of quality in PRAs that are being used to support ASME initiatives to risk informed in-service inspection (ISI) and in-service testing (IST) of nuclear power plant components. A related need supported by the industry and the U.S. Nuclear Regulatory Commission is to reduce the level of effort that is being expended in pilot applications of risk informed initiatives to address questions about the sufficiency of quality in the supporting PRA models. The purpose of this paper is to discuss the authors' views on some of the technical issues that were encountered in the effort to develop the ASME PRA standard. Draft 12 of this standard has ...
The nature of the electrolyte strongly influences the electrode kinetics of the oxygen evolution reaction (OER) and electrochemical ozone production (EOP) mainly by affecting the degree of coverage by the intermediates of both processes. The anomalous behaviour of the Tafel coefficient, b, as a function of temperature was attributed to surface adsorption of the electrolyte species, and the competition between them, as well as gas bubble adherence. Comparison of the current efficiencies of the EOP, PHI_E_O_P, determined for different temperatures and supporting electrolyte compositions, showed the presence of fluorinated anions increases PHI_E_O_P. The influence of the anion nature on PHI_E_O_P, when analysed in the light of the proposed electrode mechanism, reveals introduction into the electrolyte of anions having a high electronegativity changes the double layer structure resulting in an increase of surface concentration of the active centres ...
The objective of this research was to determine improved thermal, epithermal, and fast fluxes and several responses at mechanical test surveillance location keys 2, 4, 5, and 7 of the pressure vessel of the Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) for the beginning of the fuel cycle. The purpose of the research was to provide essential flux data in support of radiation embrittlement studies of the pressure vessel shell and beam tubes at some of the important locations.
Steam generator tube denting is primarily caused by build-up of corrosion products at the tubesheet and the tube support plates. The mechanism of dent growth and the identification of tubes which should be removed from service have been studied. The practical outcome has been to prevent in-service tube leaks and to avoid unnecessary plugging of large numbers of tubes. A finite element study of tubesheet deformation (of pulled leaking tubes from reactors) was undertaken. Profilometry results for characterizing dents are given. Although several modifications have been made the high resolution profilometry system performance and the results obtained have proved satisfactory. (U.K.).
The equivalence of representations of symmetry groups operating upon wave-functions in configuration space is studied with regard to the (intuitive) notion of physical equivalence. A refinement of the usual projective equivalence relation is introduced, called gauge equivalence, for which the allowed unitary equivalence transformations are gauge transformations. For a Euclidean as well as for Newton-Hooke symmetry group the gauge equivalence classes of unitary multiplier representations are determined. These examples support the assertion that equivalence from a physical viewpoint corresponds better to this new gauge equivalence concept than to the usual notion of projective equivalence. (author).
In recent years very good experience has been accumulated with self-supporting low-pressure blades. Today blades are constructed up to a length of 1060 mm (50 Hz) or 1360 mm (25 Hz). In this process modern computational methods from aerodynamics and also from mechanics are employed. The further development of computer technology also permits new methods, for example the use of curved fixed blading as well as the optimization of existing designs. (orig.).
Two new identical insertion devices have been designed for the Daresbury SRS. They are 2T permanent-magnet multipole wigglers that will provide high flux in the X-ray region. This paper describes the magnetic and mechanical design of the arrays of steel pole pieces and permanent-magnet blocks. Also given is the engineering design of the support structure that will cope with the very large forces present while maintaining high levels of precision in gap setting and parallelism. The engineering design has been fully assessed using finite-element techniques to predict the deflections of critical parts of the structure. These two devices are due to be installed into the SRS by the end of 1998.
On Day 363, a negative 360-degree roll turn with spacecraft ... Ill. DSN Support Assessment. As an indication of the high level support provided by the ...
To understand more fully the mechanism of enzyme-catalyzed phospho group transfer, the stereochemical course at phosphorus of four enzymes has been determined. First, using adenosine (..gamma..-(S)-/sup 16/O, /sup 17/O, /sup 18/O)triphosphate as the substrate, the reaction catalyzed by creatine kinase has been found to proceed with overall inversion of configuration at phosphorus. Second, using adenosine (..beta..-(S)-/sup 16/O, /sup 17/O, /sup 18/O)diphosphate as the substrate, the reaction catalyzed by adenylate kinase has been found also to proceed with overall inversion. Third, the reaction catalyzed by phosphoenolpyruvate carboxylase has been studied using ((S/sub p/)-/sup 16/O, /sup 17/O)thiophospoenolpyruvate as the substrate in H/sub 2/ /sup 18/O. Fourth, using adenosine 5'-O-((..gamma..S/sub p/)-..beta gamma..-/sup 17/O,..gamma..-/sup 17/O,/sup 18/O)(3-thiotriphosphate) as the substrate, the reaction catalyzed by pyruvate carboxylase has been ...
Samples of ultra-high molecular weight polyethylene (UHMWPE) and nylon 66, of grades suitable for use in medical prostheses, were subjected to irradiation using a /sup 60/Co source. The effects of a 10 Mrad dose on percentage crystallinity, tensile behaviour and dynamic mechanical response were established 3 days after irradiation at intervals over a one year period. Crystallinity in UHMWPE was found to increase progressively during this period with consequent changes in mechanical behaviour. It is proposed that the observed ageing process arises from the breakdown of metastable groups in the polymer, which are formed on irradiation, with consequent release of long inter-lamella tie chains. This removes an inhibition to crystal perfection processes, which can occur at room temperature in polyethylene. Infra-red spectroscopic evidence supports the proposal that the metastable species is peroxy or hydroperoxy and that this ...
A highly reliable control rod drive mechanism (CRDM) installed inside the reactor vessel has developed for use of an advanced marine reactor. This CRDM contributes to compactness and simplicity of the reactor system, and it can eliminate the possibility of a rod ejection accident. The CRDM works in the high temperature and high pressure water - 310degC and 12 MPa, the same atmosphere as the primary loop. Driving force is produced by a synchronous motor with the rotor of a permanent magnet, which has been developed. An innovative latch mechanism using separable ball nuts can latch driving shaft connecting the control rod and de-latch it for scram. The rod position detector using a magnetostrictive wire type sensor on the principle of Wiedeman effect has been developed, accuracy of which is verified to have a detecting error within 1.2 mm. Ball bearings for thrust and radial supports in rotation have been developed to be ...
In order to model transport of dissolved ions in subsurface environments, one should understand how these ions interact with solid phase adsorbents. Our primary goal has been investigating the reaction mechanisms which affect microcontaminant partitioning between aqueous solutions and solid phase adsorbents, using goethite ({alpha}-FeOOH) as a model adsorbent. Cylindrical internal reflection -- Fourier transform infrared (CIR-FTIR) spectroscopy has been developed as the primary technique for this study. Wet chemical adsorption studies, acoustophoresis and electrophoretic mobility have been used to obtain supporting information as needed. Phenol and o-nitrophenol did not adsorb to goethite. Benzoate, phthalate and p-hydroxybenzoate all adsorbed via a bidentate mechanism to two adjacent iron atoms, while salicylate and 2,4-dihydroxybenzoate formed a chelate complex to single iron atoms. Phosphate adsorption was predominately ...
The primary function of the Waste Handling Shaft (WHS) at the Waste Isolation Pilot Plant (WIPP) is to permit the transfer of radioactive waste from the surface waste handling building to the underground storage area. It also serves as an intake shaft for small volumes of air during normal storage operations and as an emergency escape route. Part of the construction was the placement of a concrete liner and steel reinforced key in 1984. During a routine shaft inspection in May 1990, some degradation of the WHS concrete liner was observed between the depths of 800 and 900 feet below the ground surface. Detailed investigations of the liner had been carried out by Sandia National Laboratories and by Westinghouse Electric Corporation Waste Isolation Division (WID) through Lankard Materials Laboratory. Observations, reports, and data support the conclusion that the concrete degradation, resulting from attack by chemically aggressive brine, is a localized phenomena. It ...
The purpose of this Analysis and Model Report (AMR) supporting the Site Recommendation/License Application (SR/LA) for the Yucca Mountain Project is the development of elementary analyses of the interactions of a hypothetical dike with a repository drift (i.e., tunnel) and with the drift contents at the potential Yucca Mountain repository. This effort is intended to support the analysis of disruptive events for Total System Performance Assessment (TSPA). This AMR supports the Process Model Report (PMR) on disruptive events (CRWMS M&O 2000a). This purpose is documented in the development plan (DP) ''Coordinate Modeling of Dike Propagation Near Drifts Consequences for TSPA-SR/LA'' (CRWMS M&O 2000b). Evaluation of that Development Plan and the work to be conducted to prepare Interim Change Notice (ICN) 1 of this report, which now includes the design option of ...
The oxidative dehydrogenation (OXDH) of n-butane, 1-butene, and trans-2-butene on different vanadia catalysts has been compared. MgO, alumina, and Mg-Al mixed oxides with Mg/(Al + Mg) ratios of 0.25 and 0.75 were used as supports. The catalytic data indicate that the higher the acid character of catalysts the lower is both the selectivity to C{sub 4}-olefins from n-butane and the selectivity to butadiene from both 1-butene or trans-2-butene. Thus, OXDH reactions are mainly observed from n-butane and butenes on basic catalysts. The different catalytic performance of both types of catalysts is a consequence of the isomerization of olefins on acid sites, which appears to be a competitive reaction with the selective way, i.e., the oxydehydrogenation process by a redox mechanism. Infrared spectroscopy data of 1-butene adsorbed on supported vanadium oxide catalysts suggest the presence of different adsorbed species. O-containing ...
There are two major distinct activities involved with reprocessing of nuclear fuel. They are: a) Mechanical handling of the fuel in the head end plants; and b) chemical dissolution and separation of unused fuel, useful by-products and waste products. Plants and facilities associated with the former include significant remote handling equipment that is designed for handling of fuel for normal production processes. These equipment are selected and designed to meet the design throughput of the plant taking into consideration ease of their operation and maintenance in conjunction with statutory regulations on safety and operator dose uptake. Nevertheless, during the life of the plant, there are instances when special equipment is called for to access part of the plant and undertake tasks such as inspection, maintenance and modification to improve the existing process. BNFL has much experience in the design and application of remote handling equipment for normal ...
Operating PWR units in the USA have experienced very severe corrosion of the tube support plate at the crevice between the tube and the support. This results in distortion of the plate and crushing of the tube (denting). The first task of this project required that currently available computational methods to estimate the pH attained by concentrating boiler water under various fault conditions such as condenser leakage of river waters and faulty operation of condensate polishing plant. Particular attention has been paid to systems in which sulfate predominates. In the second task, the mechanisms are discussed by which solutions become concentrated in porous deposits on a boiling heat transfer surface. It is concluded that more experimental data are needed to test the validity of existing models. High solution concentrations in the deposit may occur at a heat flux close to the critical value for drying out the base of the ...
This technical report was written as a result of Integrated Plant Information System (IPIS) feasibility study on CANDU 9 project which had been carried out from January, 1994 to March, 1994 at AECL (Atomic Energy Canada Limited) in Canada. From 1987, AECL had done endeavour to change engineering work process from paper based work process to computer based work process through CANDU 3 project. Even though AECL had a lot of good results form computerizing the Process Engineering, Instrumentation Control and Electrical Engineering, Mechanical Engineering, Computer Aided Design and Drafting, and Document Management System, but there remains the problem of information isolation and integration. On this feasibility study, IPIS design support functionality guideline was suggested by evaluating current AECL CAE tools, analyzing computer aided engineering task and work flow, investigating request for implementing integrated computer aided engineering ...
Single crystal tungsten oxide (WO3) nanoparticles were prepared via a microwave-assisted method. Electrochemical activity for hydrogen evolution reaction (HER) on WO3 supported on carbon black (WO3/C) electrocatalyst was first studied in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH) at room temperature. The overall experimental results revealed that the electrocatalytic activity for HER on WO3/C is one order magnitude higher than those obtained with carbon black in 0.5 M H2SO4 and is six times than in the case of carbon black in 1.0 M KOH. These results demonstrated that WO3 could enhance the electrocatalytic activity for hydrogen evolution reaction in acid solution (0.5 M H2SO4) and alkaline solution (1.0 M KOH). On the other hand, the kinetic reaction mechanisms were disc...
With the passing of the Energy Policy Act of 2005, the United States is experiencing for the first time in over two decades, what some refer to as the 'Nuclear Renaissance'. The US Nuclear Regulatory Commission (NRC) recognizes this surge in application submissions and is committed to reviewing these applications in a timely manner to support the country's growing energy demands. Notwithstanding these facts, it is understood that the nuclear industry requires appropriately trained and educated personnel to support the growing needs of the nuclear industry and the US NRC. Equally important is the need to educate the next generation of students in nuclear non-proliferation, nuclear forensics and various aspects of homeland security for the national laboratories and the Department of Defense. From mechanical engineers educated and experienced in materials, thermal/fluid dynamics, and component ...
The current status of the ZTH vacuum liner design is covered by this report. ZTH will be the first experiment to be installed in the CPRF (Confinement Physics Research Facility) at the Los Alamos National Laboratory and is scheduled to be operational at the rated current of 4 MA in 1992. The vacuum vessel has a 2.4 m major radius and a 40 cm minor radius. Operating parameters which drive the vacuum vessel mechanical design include a 300 C bakeout temperature, an armour support system capable of withstanding 25 kV, a high toroidal resistance, 1250 kPa magnetic loading, a 10 minute cycle time, and high positional accuracy with respect to the conducting shell. The vacuum vessel design features which satisfy the operating parameters are defined. The liner is constructed of Inconel 625 and has a geometry which alternates sections of thin walled bellows with rigid ribs. These composite sections span between pairs of the 16 diagnostic stations to ...
The isomerization of neopentane has been investigated over the 0.76 wt% Pd/SiO{sub 2} catalyst. It is found that after high temperature reduction (HTR, at 873 K) the selectivity for isomerization is much higher than that after low temperature reduction (LTR, at 573 K). A variety of experiments, including kinetic, chemisorption (O{sub 2}, H{sub 2}, and CO), temperature-programmed desorption of H{sub 2}, and X-ray diffraction, showed that this selectivity enhancement cannot be interpreted in terms of H{sub 2} retention by catalyst. Instead, the formation of Pd-Si compound(s) (most probably Pd{sub 3}Si) during HTR seems immediately responsible for the catalytic behavior of HTR Pd/SiO{sub 2} catalysts. A mechanism is proposed for the Pd-SiO{sub 2} interaction in which Pd atoms (or ions) are incorporated into the silica support (via oxygen vacancies) and a new phase of palladium silicide is formed. Regeneration by an oxygen treatment of the HTR ...
A general overview is provided of the Wind Energy Research and Development Program (WERD) structure, status, and current perspectives, and a highlight of recent achievements. The broad objectives of WERD are to: determine under what circumstances wind energy can make a viable contribution to Canadian energy supplies; establish the technology of wind energy conversion systems (WECS) to appropriate Canadian conditions; and to encourage and support Canadian industrial initiatives in the design and manufacture of WECS for both domestic and export markets. Field trials supported by WERD include: six small scale Savonius/Darrieus vertical axis wind turbines (VAWT) rated at 1 to 3 kW installed throughout Canada; a 37 kW VAWT mechanically coupled to a 50 kW diesel-electric set as part of a 100 kW remote community powerplant; five 50 kW grid-coupled VAWT generating systems; a 224 kW VAWT grid-coupled system in cooperation with Hydro ...
The onshore Potiguar basin has nowadays around 5.000 artificial lifting petroleum wells, distributed into 80 fields located on the states of Rio Grande do Norte and Ceara, representing approximately 8% of the national oil production. For that, well maintenance service, realized by Workover Rigs, is essential to preserve the oil productivity of the reservoirs on these fields. However, as the number of rigs is lower than to the number of wells needing maintenance, the task of administrating the management of such equipment according to the demand created by the wells, generates an optimization problem. The decision for a rig intervention on a well depends on parameters such as flow rate, depth, wasted time on intervention, distance from the rig to the next well, type of operation, rig capacity, environmental risks, etc. The objective of this paper is to present an interactive Computational System for Support Decision to the optimized management of the wells attended ...
In this paper, we investigate the relationship between the subprime asset-backed collateralized debt obligations (CDO) market and Large Complex Financial Institutions (LCFIs). We attempt to account for the dynamics between the ABX index returns and the banks' equity returns through conditioning our analysis on the historical correlation between the variables. Three key results emerge from the analysis. First, we find a positive correlation between movements of the ABX index and the equity returns for all the LCFIs. Second, the volatility of ABX index returns tend to be transmitted to the volatilities of the equity returns of the financial institutions. Third, ABX prices changes lead equity returns changes of the European-based LCFIs. For the US LCFIs a two-way linkage emerges.
Parthenogenesis-inducing (PI) Wolbachia belong to a class of intracellular symbionts that distort the offspring sex ratio of their hosts toward a female bias. In many PI Wolbachia-infected species sex ratio distortion has reached its ultimate expression-fixation of infection and all-female populations. This is only possible with thelytokous PI symbionts as they provide an alternative form of reproduction and remove the requirement for males and sexual reproduction. Many populations fixed for PI Wolbachia infection have lost the ability to reproduce sexually, even when cured of the infection. We examine one such population in the species Trichogramma pretiosum. Through a series of backcrossing experiments with an uninfected Trichogramma pretiosum population we were able to show that the gen...
The Clean Air Act Amendments of 1990, established requirements for the Environmental Protection Agency (EPA) to develop rules for the establishment of enhanced ozone monitoring networks or Photochemical Assessment Monitoring Stations (PAMS) in ozone nonattainment areas designated as serious, severe, and extreme. The subsequent rules require these stations to collect ambient air measurements for a target list of volatile organic compounds including several carbonyls, oxides of nitrogen, ozone, and meteorological measurements, both surface and upper air. Twenty-two areas in the US are obligated to install and operate PAMS stations to aid in the identification, development, and implementation of effective ozone control strategies. This paper will examine the specific requirements of the PAMS rules and will provide information regarding the current status of the networks and overall implementation issues.
To meet BPA`s contractual obligation to supply electrical power to its customers, BPA proposes to acquire power generated by Klickitat Cogeneration Project. BPA has prepared an environmental assessment evaluating the proposed project. Based on the EA analysis, BPA`s proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969 for the following reasons: (1)it will not have a significant impact land use, upland vegetation, wetlands, water quality, geology, soils, public health and safety, visual quality, historical and cultural resources, recreation and socioeconomics, and (2) impacts to fisheries, wildlife resources, air quality, and noise will be temporary, minor, or sufficiently offset by mitigation. Therefore, the preparation of an environmental impact statement is not required and BPA is issuing this FONSI (Finding of No Significant Impact).
The rapid pace of competitive change in the generation sector has pushed electric utilities to rethink the concept of being obligated to serve all customers and with this change, the notion of measuring customer profitability is also being redefined. Traditionally, uniform services were provided to all customers. Rates were based on each customer classes` contribution to average costs, and consequently return was equally allocated across all customer segments. Profitability was defined strictly on an aggregate basis. The increasing demand for choice by electric customers will require electricity providers to redefine if not who they serve, than certainly how they provide differentiated services tailored to specific customer segments. Utilities are beginning to analyze the value, or profitability, of offering these services. Aggregate data no longer provides an accurate assessment of how resources should be allocated most efficiently. As services are unbundled, so ...
This report summarizes the major features of the advisory tool `TUNDTEMP`, developed to act as a decision support in the continuous steel casting process. `TUNDTEMP` provides a means to predict abnormal phenomena of temperature origin in the casting that may be difficult to foresee in practical situations. The heart of the system is a semi-empirical calculation model that yields an estimate of the evolution of the tundish temperature of the liquid steel on the basis of a few important casting factors. The user interface of the system is to a large extent based on the visual presentation of the simulated results. The system also contains an optional rule based mechanism that provides assistance in the result interpretation and, if wished, linguistically formulates action recommendations. A separate program has been built for the tuning of the calculation model and for maintenance of the system. At the end of the report, the different tuning ...
We review the current status of resolved X-ray emission associated with extragalactic radio jets and hotspots. The primary question for any particular jet is to decide if the X-rays come from the synchrotron process or from inverse Compton scattering. There is considerable evidence supporting synchrotron emission for knots in the jets of FRI galaxies. For FRII terminal hotspots detected in the X-ray band, synchrotron self-Compton emission continues to provide viable models with one possible exception (so far). Inverse Compton scattering on photons of the cosmic microwave background is indicated for a few powerful jets, and is expected to be an important contributor if not the dominating mechanism for higher redshift objects. The application of a model generally yields physical parameters and in many cases, these include the Doppler boosting factor.
The thermal spike model has been successfully applied to track formation by swift heavy ions in insulators. Arguments are given supporting the assumption that the thermal spike mechanism is also valid for the anisotropic growth. The glass transition temperature is used as the main thermal parameter of the amorphous solids. Experimental results on the track formation in {alpha}-quartz and in crystalline Ni{sub 3}B and also on the anisotropic growth in Pyrex and Synsil glasses, in amorphous Pd{sub 80}Si{sub 20}, Ni{sub 3}B and Fe{sub 85}B{sub 15} are discussed. Good agreement is found with the predictions of the thermal spike model. (orig.).
For the safety of astronauts and to ensure the stability and integrity of the genome of microorganisms and plants used in bioregenerative life support systems, it is important to improve our knowledge of the combined action of (space) radiation and microgravity. The SOS-LUX-TOXICITY test, as part of the TRIPLE-LUX project (accepted for flight at Biolab in Columbus on the International Space Station, (ISS)), will provide an estimation of the health risk resulting from exposure of astronauts to the radiation environment of space in microgravity. The project will: (i) increase our knowledge of biological/health threatening action of space radiation and enzymatic DNA repair; (ii) uncover cellular mechanisms of synergistic interaction of microgravity and space radiation; (iii) provide specified...
Jet-driven shocks are responsible for an important fraction of the emission of the narrow-line regions (NLRs) in many classes of AGN. However, this cannot explain all observations. It is clear that the remaining sources are photoionised by the active nucleus. The 2-d hydrodynamic models from the RSAA group support an evolutionary scenario whereby the shock-excited NLRs are initially jet-driven but later, ionizing photons from the central engine replace shocks as the main excitation mechanism and shock induced star formation may also become important. In their photoionized phase, dusty and radiation-pressure dominated evolution produces a self-regulated NLR spectrum. This model aso explains the coronal emission lines and fast (3000 km s$^{-1}$) outflows seen in some Seyferts.
Mesocarp tissue from sucrose-accumulating sweet melon (Cucumis melo cv. Galia) showed sucrose synthase activity (ca 1 nkat/gfw) while soluble acid invertase and sucrose phosphate synthase activities were not observed. Sucrose uptake into mesocarp discs was linear with sucrose concentration (1-500 mM) and unaffected by PCMBS and CCCP. Sucrose compartmentation into the vacuole also increased linearly with sucrose concentration as indicated by compartmental efflux kinetics. Mesocarp discs incubated in /sup 14/C-fructose + UDP-glu synthesized /sup 14/C-sucrose and efflux kinetics indicated that the /sup 14/C-sucrose was compartmentalized. These data support the hypothesis that two mechanisms are involved in sucrose accumulation in sweet melon: (1) compartmentation of intact sucrose and (2) synthesis of sucrose via sucrose synthase and subsequent compartmentation in the vacuole.
The condensation reaction of furfural (F) on acetone (Ac) gives a high added value product, the 4-(2-furyl)-3-buten-2-one (FAc), used as aroma in alcohol free drinks, ice, candies, gelatines and other products of current life. This synthesis valorises the residues of sugar cane treatment since furfural is obtained by hydrolysis of sugar cane bagasse followed by vapor training extraction. In the face of numerous and complex reactions involved in this synthesis, it is very complicated to define the kinetic laws from exact stoichiometry. A solution allowing to cope the problem consists in identifying an appropriate stoichiometric model. It does not attempt to represent exactly all the reaction mechanisms, but proposes a mathematical support to integrate available knowledge on the transformati...
Dusty primordial disks surrounding young low-mass stars are revealing tracers of stellar and planetary formation. The evolution and lifetime of these disks define the boundary conditions of the mechanisms of planet formation. Stellar companions, however, can significantly change this evolution through their tidal interactions. Stellar evolution and planet formation in binaries have to respond to an environment of truncated, quickly disappearing disks--very different compared to an isolated star environment. In order to investigate details of the influence of binarity on circumstellar disk evolution, we obtained adaptive optics supported near-infrared imaging and spectroscopy of the individual components of 22 low-mass binaries in the well-known Orion Nebula Cluster. Brackett gamma emission, which we detect in several systems, is used as a tracer for the presence of an active accretion disk around each binary component. We find a low fraction of ...
In support of the efforts to apply ceramics to advanced heat engines, a study is being performed of the performance of ceramics at the ring/cylinder interface of advanced (low heat rejection) engines. The objective of the study, managed by the Oak Ridge National Laboratory, is to understand the basic mechanisms controlling the wear of ceramics and thereby identify means for applying ceramics effectively. Attempts to operate three different zirconias, silicon carbide, silicon nitride, and plasma-sprayed ceramic coatings without lubrication have not been successful because of excessive friction and high wear rates. Silicon carbide and silicon nitride perform well at ambient temperatures with fully formulated mineral oil lubrication, but are limited to temperatures of 500F because of the lack of suitable liquid lubricants for higher temperatures.
We show that accretion disks, both in the subcritical and supercritical accretion rate regime, may exhibit significant amplitude luminosity oscillations. The luminosity time behavior has been obtained by performing a set of time-dependent 2D SPH simulations of accretion disks with different values of ? and accretion rate. An explanation of this luminosity behavior is proposed in terms of limit-cycle instability: the disk oscillates between a radiation pressure dominated configuration (with a high luminosity value) and a gas pressure dominated one (with a low luminosity value). The origin of this instability is the difference between the heat produced by viscosity and the energy emitted as radiation from the disk surface (the well-known thermal instability mechanism). We support this hypothesis showing that the limit-cycle behavior produces a sequence of collapsing and refilling states of the innermost disk region.
A kinetic model based on the Mars-van Krevelen mechanism that allows to describe the microkinetics of the heterogeneously catalysed partial oxidation of {alpha}, {beta}-unsaturated aldehydes is presented. This conversion is represented by a network, composed of the oxidation of the {alpha}, {beta}-unsaturated aldehyde towards the {alpha}, {beta}-unsaturated carboxylic acid and the consecutive oxidation of the acid as well as the parallel reaction of the aldehyde to products of deeper oxidation. The reaction steps of aldehyde respectively acid oxidation and catalyst reoxidation have been investigated separately in transient experiments. The combination of steady state and transient experiments has led to an improved understanding of the interaction of the catalyst with the aldehyde and the carboxylic acids as well as to a support of the kinetic model assumptions. (orig.)
The determination of Li and proton-capture element abundances in globular cluster (GC) giants allows us to constrain several key questions on the multiple population scenarios in GCs, from formation and early evolution to pollution and dilution mechanisms. In this Letter, we present our results on Li abundances for a large sample of giants in the intermediate-metallicity GC NGC 6121 (M4), for which Na and O have been already determined by Marino et al. The stars analyzed are both below and above the red giant branch bump luminosity. We found that the first and second generation stars share the same Li content, suggesting that a Li production must have occurred. This provides strong observational evidence supporting the scenario in which asymptotic giant branch stars are GC polluters.
The potential association between xenotropic murine leukaemia virus-related gammaretrovirus (XMRV) and prostate cancer (PCa) has been documented since 2006. It is important for furthering our understanding of the biological mechanisms of PCa to ascertain whether this association is causal. To summarize the available information on the epidemiological and laboratory findings of the association, we conducted a literature search of the PubMed electronic database (from March 2006 to February 2011) to identify relevant published studies that examined the association between XMRV and PCa. Although several studies showed the positive association between XMRV and PCa, more recent studies did not support this conclusion. The positive findings might be due to contamination of human samples. Further ...
An ion processing element employing composite media disposed in a porous substrate, for facilitating removal of selected chemical species from a fluid stream. The ion processing element includes a porous fibrous glass substrate impregnated by composite media having one or more active components supported by a matrix material of polyacrylonitrile. The active components are effective in removing, by various mechanisms, one or more constituents from a fluid stream passing through the ion processing element. Due to the porosity and large surface area of both the composite medium and the substrate in which it is disposed, a high degree of contact is achieved between the active component and the fluid stream being processed. Further, the porosity of the matrix material and the substrate facilitates use of the ion processing element in high volume applications where it is desired to effectively process a high volume flows.
A Gross Decontamination Experiment was conducted on various levels and surfaces of the TMI - Unit 2 reactor building in March 1982. The polar crane, D-rings, missile shields, refueling canals, refueling bridges, equipment, and elevations 305' and 347'-6'' were flushed with low pressure water. Additionally, floor surfaces on elevation 305' and floor surfaces and major pieces of equipment on elevation 347'-6'' were sprayed with high pressure water. Selective surfaces were decontaminated with a mechanical scrubber and chemicals. Strippable coating was tested and evaluated on equipment and floor surfaces. The effectiveness, efficiency, and safety of several decontamination techniques were established for the large, complex decontamination effort. Various decontamination equipment was evaluated and its effectiveness was documented. Decontamination training and procedures were documented and evaluated, as were the support system and organization for ...
The phenomenon of radiation blistering by helium ion bombardment has been the subject of extensive studies in recent years because of its technological importance in thermonuclear fusion devices and reactors. However, the mechanism of radiation blistering is still not well understood. There are two different models of blister formation: the gas-pressure model and the lateral stress model. The former model is, however, supported by many experimental observations, the prominent one is that of Evans and Eyre who observed blisters appearing on the front and rear surfaces of a thin wedge-shaped molybdenum foil irradiated by helium ions. Their experiment also indicates that the thickness of the irradiated specimen could be important in affecting the characteristics of blisters. With this in view, we have studied the development of blisters in thin foils of tantalum by 30 MeV ..cap alpha..-particle bombardment.
The phenomenon of radiation blistering by helium ion bombardment has been the subject of extensive studies in recent years because of its technological importance in thermonuclear fusion devices and reactors. However, the mechanism of radiation blistering is still not well understood. There are two different models of blister formation: the gas-pressure model and the lateral stress model. The former model is, however, supported by many experimental observations, the prominent one is that of Evans and Eyre who observed blisters appearing on the front and rear surfaces of a thin wedge-shaped molybdenum foil irradiated by helium ions. Their experiment also indicates that the thickness of the irradiated specimen could be important in affecting the characteristics of blisters. With this in view, we have studied the development of blisters in thin foils of tantalum by 30 MeV #alpha#-particle bombardment. (orig.).
Neutron capture ..gamma..-ray spectra have been measured at 11 average neutron energies from 10 to 530 keV in /sup 88/Sr using a 20 x 15 cm NaI detector with time-of-flight discrimination of background events. The partial radiation widths and the calculated partial valence widths are compared for the strong p-wave resonances at 287 and 321 keV and found to be highly correlated. At these energies, the spectra are dominated by strong transitions to low-lying single particle states, in confirmation of the role of valence capture in the 3p region. However, the data do not support this mechanism at <508> keV.
Neutron capture #gamma#-ray spectra have been measured at 11 average neutron energies from 10 to 530 keV in /sup 88/Sr using a 20 x 15 cm NaI detector with time-of-flight discrimination of background events. The partial radiation widths and the calculated partial valence widths are compared for the strong p-wave resonances at 287 and 321 keV and found to be highly correlated. At these energies, the spectra are dominated by strong transitions to low-lying single particle states, in confirmation of the role of valence capture in the 3p region. However, the data do not support this mechanism at <508> keV.
In device fabrication, dopants are frequently implanted into silicon through silicon dioxide masks. A consequence of this technique is the co-implantation of recoiled oxygen into the substrate. This study investigates the effect of recoiled oxygen on the widely observed transient enhanced boron diffusion. Comparison of the spreading resistance profiles of annealed through-oxide and directly implanted samples reveals that transient enhanced diffusion of boron can be suppressed by the former process. Continued annealing of the through-oxide implanted silicon recovers the enhanced diffusion of boron. This behavior is believed to be due to precipitation of recoiled oxygen. The mechanisms leading to the above observations are discussed and transmission electron microscopy support presented. 11 refs., 5 figs.
Land snails move via adhesive locomotion. Through muscular contraction and expansion of their foot, they transmit waves of shear stress through a thin layer of mucus onto a solid substrate. Since a free surface cannot support shear stress, adhesive locomotion is not a viable propulsion mechanism for water snails that travel inverted beneath the free surface. Nevertheless, the motion of the freshwater snail, Sorbeoconcha physidae, is reminiscent of that of its terrestrial counterparts, being generated by the undulation of the snail foot that is separated from the free surface by a thin layer of mucus. Here, a lubrication model is used to describe the mucus flow in the limit of small amplitude interfacial deformations. By assuming the shape of the snail foot to be a traveling sine wave and the mucus to be Newtonian, an evolution equation for the interface shape is obtained and the resulting propulsive force on the snail is calculated. This ...
Silicon sensors have about ten times improved radiation hardness around 130 K temperature, compared with the state-of-art sensors close to room temperature. This is based on the Lazarus effect studied by the RD39 Collaboration of CERN. Other benefits of low temperatures will also be discussed. We shall describe the conceptual design of low-mass detector modules cooled using two-phase flow of argon in miniature cooling pipes integrated in the module structure between the sensors and the readout hybrid circuit. The main engineering features of the cooling system and mechanicalsupport structures are discussed, as well as the benefits arising from the operation of the tracker under cryogenic vacuum. 4 Refs.
This report documents the research activities by Rogers and Associates Engineering Corporation on grant DE-FG03-93ER61600 during the funded project period from August 1993 to April 1996. The objective of this research was to characterize the mechanisms and rates of radon gas penetration of the different structural domains of the concrete components of residential floor slabs, walls, and associated joints and penetrations. The research was also to characterize the physical properties of the concretes in these domains to relate their radon resistance to their physical properties. These objectives support the broader goal of characterizing which, if any, concrete domains and associated properties constitute robust barriers to radon and which permit radon entry, either inherently or in ways that could be remediated or avoided.
Prompted by work on the buckling instability in barred spiral galaxies, much effort has been devoted lately to the study of boxy/peanut-shaped (B/PS) bulges. Here, we present new bar diagnostics for edge-on spiral galaxies based on periodic orbits calculations and hydrodynamical simulations. Both approaches provide reliable ways to identify bars and their orientations in edge-on systems. We also present the results of an observational search for bars in a large sample of edge-on spirals with and without B/PS bulges. We show that most B/PS bulges are due to the presence of a thick bar viewed edge-on while only a few may be due to accretion. This strongly supports the bar-buckling mechanism for the formation of B/PS bulges.
Anaphylaxis is a serious allergic reaction that is rapid in onset and sometimes leads to death. Understanding mechanisms, triggers, and patient-specific risk factors for severe or fatal anaphylaxis is critically important. Diagnosis of anaphylaxis is currently based on established clinical criteria. Epinephrine (adrenaline) is the first-line medication for anaphylaxis treatment and delay in injecting it contributes to biphasic reactions, hypoxic-ischemic encephalopathy, and fatality. Here, we focus on four important areas of translational research in anaphylaxis: studies of potential new biomarkers to support the clinical diagnosis of anaphylaxis, laboratory tests to distinguish allergen sensitization from clinical risk of anaphylaxis, the primary role of epinephrine (adrenaline) in anaphylaxis treatment, and strengthening the overall evidence base for anaphylaxis treatment. PMID:21668849
The research documented herein was funded by a research contract between the Research Reactors Division (RRD) of Oak Ridge National Laboratory (ORNL) and the University of Tennessee, Knoxville (UTK) Mechanical, Aerospace and Biomedical Engineering Department (MABE). The research was governed by a statement of work (SOW) which clearly defines nine specific tasks. This report is outlined to follow and document the results of each of these nine specific tasks. The primary goal of this phase of the research is to demonstrate, through verification and validation methods, that COMSOL is a viable simulation tool for thermal-hydraulic modeling of the High Flux Isotope Reactor (HFIR) core. A secondary goal of this two-dimensional phase of the research is to establish methodology and data base libraries that are also needed in the full three-dimensional COMSOL simulation to follow. COMSOL version 3.5a was used for all of the models presented throughout this report.
The collapse of a massive star's core, followed by a neutrino-driven, asymmetric supernova explosion, can naturally lead to pulsar recoils and neutron star kicks. Here, we present a two-dimensional, radiation-hydrodynamic simulation in which core collapse leads to significant acceleration of a fully-formed, nascent neutron star (NS) via an induced, neutrino-driven explosion. During the explosion, a ~10% anisotropy in the low-mass, high-velocity ejecta lead to recoil of the high-mass neutron star. At the end of our simulation, the NS has achieved a velocity of ~150 km s$^{-1}$ and is accelerating at ~350 km s$^{-2}$, but has yet to reach the ballistic regime. The recoil is due almost entirely to hydrodynamical processes, with anisotropic neutrino emission contributing less than 2% to the overall kick magnitude. Since the observed distribution of neutron star kick velocities peaks at ~300-400 km s$^{-1}$, recoil due to anisotropic core-collapse supernovae provides a natural, non-exotic ...
Silica and bridged polysilsesquioxane aerogels are low-density materials that are attractive for applications such as thermal insulation, porous separation media or catalyst supports, adsorbents, and cometary dust capture agents. However, aerogels are notoriously weak and brittle making it difficult to handle and machine monoliths into desired forms. This complication prevents the development of many applications that would otherwise benefit from the use of the low-density materials. Here, we will describe our efforts to chemically modify and mechanically enhance silica-based aerogels using chemical vapor techniques without sacrificing their characteristic low densities. Monolithic silica and organic-bridged polysilsesquioxane aerogels were prepared by sol-gel polymerization of the respective methoxysilane monomers followed by supercritical carbon dioxide drying of the gels. Then the gels were reactively modified with silylating agents to ...
Cooperation for low carbon and energy efficient development is a high priority for France, in line with the United Nations Framework Convention on Climate Change. France contributes to tackling climate change by working with its partners on all continents to implement projects both to mitigate greenhouse gas emissions and to adapt to climate change. Within the framework of the Marrakech Accords, France also encourages the implementation of the Kyoto Protocol Clean Development Mechanism, in particular between French business and non-Annex I countries; this mechanism will facilitate the financing of mitigation projects and contribute to the sustainable development of host countries in the South. At multilateral level, France is a major donor. At a bilateral level, an initial analysis of cooperation projects which are strongly linked to tackling climate change identified public support of 136 millions euros per year, as an ...
Evolutionary theory holds that aging is a consequence of the declining force of natural selection with age. We discuss here the evidence that among the causes of aging in complex multicellular organisms, such as mammals, is the antagonistically pleiotropic effects of the cellular responses that protect the organism from cancer. Cancer is relatively rare in young mammals, owing in large measure to the activity of tumor suppressor mechanisms. These mechanisms either protect the genome from damage and/or mutations, or they elicit cellular responses--apoptosis or senescence--that eliminate or prevent the proliferation of somatic cells at risk for neoplastic transformation.We focus here on the senescence response, reviewing its causes, regulation and effects. In addition, we describe recent data that support the idea that both senescence and apoptosis may indeed be the double-edged swords predicted by the evolutionary hypothesis ...
In 2005, the American Medical Informatics Association undertook a set of activities relating to clinical decision support (CDS), with support from the office of the national coordinator and the Agency...Full Text Available
Lateral and vertical variabilities in the bulk and mechanical properties of silicic volcanic tuff at the potential nuclear waste repository site in Yucca Mountain, NV have been evaluated. Laboratory measurements have been performed on tuff specimens recovered from boreholes located to support the design of the Exploratory Studies Facility/North Ramp. The data include dry and saturated bulk densities, average grain density, porosity, compressional and shear wave velocities, elastic moduli, and compressional and tensional fracture strengths. Data from eight boreholes aligned in a northwest-southeast direction have been collected under the required quality assurance program. Three boreholes have penetrated the potential repository horizon. The information collected provides for an accurate appraisal of the variability of rock properties in the vicinity of the boreholes. As expected, there is substantial variability in the bulk and ...
The subjective experience of one's environment is constructed by interactions among sensory, cognitive, and affective processes. For centuries, meditation has been thought to influence such processes by enabling a nonevaluative representation of sensory events. To better understand how meditation influences the sensory experience, we used arterial spin labeling functional magnetic resonance imaging to assess the neural mechanisms by which mindfulness meditation influences pain in healthy human participants. After 4 d of mindfulness meditation training, meditating in the presence of noxious stimulation significantly reduced pain unpleasantness by 57% and pain intensity ratings by 40% when compared to rest. A two-factor repeated-measures ANOVA was used to identify interactions between meditation and pain-related brain activation. Meditation reduced pain-related activation of the contralateral primary somatosensory cortex. Multiple regression analysis was used to ...
In this experiments, we established long-termed culture methods of bone marrow stromal cells for proliferation and differentiation of stem cells. And we selected some extracts which support maximal proliferation of stromal cells with this method. We conformed the synergic effects of herval mixture extracts for stromal cell growth. The proliferation of stromal cells was increased rather by the addition of mixture extracts than by addition of single strain extract. In the previous and cooperative experiments, we selected complex extracts which increased the number of nonadherent mononuclear cells. Different cytokine expression patterns were observed stromal cells cultured in the presence or absence of mixture extracts which support differentiation of nonadherent cells. Stimulation of macrophage cell line with herval extracts with the treatments of recombinant interferon-{gamma} resulted in increased nitric oxide synthesis in a dose-dependent ...
In this experiments, we established long-termed culture methods of bone marrow stromal cells for proliferation and differentiation of stem cells. And we selected some extracts which support maximal proliferation of stromal cells with this method. We conformed the synergic effects of herbal mixture extracts for stromal cell growth. The proliferation of stromal cells was increased rather by the addition of mixture extracts than by addition of single strain extract. In the previous and cooperative experiments, we selected complex extracts (Him-I, Him-II) which increased the number of nonadherent mononuclear cells. Different cytokine expression patterns were observed stromal cells cultured in the presence or absence of mixture extracts which support differentiation of nonadherent cells. Some fractions of Him-I and Him-II increased the proliferation of bone marrow cells irradiated {gamma}-ray(4Gray). Stimulation of macrophage cell line with herval ...
Following the Chernobyl nuclear disaster, a considerable amount of effort and resources were allocated worldwide to designing and developing coherent and comprehensive decision support systems for nuclear or radiological emergency management. They range from simple radiological consequence assessment tools to more advanced systems, incorporating the assessment of countermeasures and their effectiveness. Furthermore, many of these systems have been tailored to answer to national emergency preparedness requirements and in some cases such as the R.O.D.O.S. and A.R.G.O.S. systems they have been successfully deployed in a number of countries. Thus, computer based decision support systems for nuclear emergencies are nowadays a reality in Europe, the US and Japan; however, there was a lack of an adequate information and data exchange mechanism that enabled them to function properly and serve the purpose that triggered their ...
Hydrocarbon synthesis during CO hydrogenation over Pd/M-ZSM5 (M=H,Na,La) and Pd/SiO/sub 2/ has been investigated. Overall activity depended on the cation-exchanged form of the support and decreased in the order Pd/La-ZSM5 = Pd/Na-ZSM5 > Pd/H-ZSM5 > Pd/SiO/sub 2/. The zeolite-supported catalysts showed high selectivity towards saturated C/sub 2/-C/sub 6/ hydrocarbons, whereas Pd/SiO/sub 2/ favored methanol production. Increasing temperature and H/sub 2//CO feed ratio led to higher reaction rates, lower yields of C/sub 2/-C/sub 6/ products, and increased lighter hydrocarbons. A mechanical mixture of Pd/SiO/sub 2/ and Na-ZSM5 showed similar product distribution as Pd/Na-ZSM5. Infrared spectra of the catalysts under reaction conditions indicate the presence of adsorbed oxygenates on the zeolite. Changes in the IR bands during the initial stages of the reaction suggest that surface species on the zeolite are not methanol ...
The catalytic nature of Mo(CO)/sub 6/ supported on ..gamma..-Al/sub 2/O/sub 3/, KOH-doped ..gamma..-Al/sub 2/O/sub 3/, and HY-zeolite was investigated in CO oxidation with N/sub 2/O in comparison with that of a conventional partially reduced MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst. Kinetic parameters of this reaction were obtained in the range 0 to 100/sup 0/C; the rate law r = kP/sub N/sub 2/O//sup 1/P/sub CO//sup 0/ was found on all catalysts, and the activation energy was estimated to be 9.1 kcal/mol on the Mo(CO)/sub 6/-derived catalysts and 7.1 kcal/mol on the partially reduced MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst. Maximum catalytic activities were obtained by activating the Mo(CO)/sub 6/-derived catalysts at 400/sup 0/C. To obtain similar activity on the MoO/sub 3//..gamma..-Al/sub 2/O/sub 3/ catalyst, it was necessary to reduce at 600/sup 0/C. The former catalysts were deactivated on repeating the reaction. On the basis of these results ...
The stand is designed to test supports of development workings. To expand the test range for various types of supports, the cross pieces have fixing devices in the form of winches interacting by cables through blocks fastened to the stand body with the support hinges.
In the beginning of 2005 several changes in the electricity and natural gas market law came into effect. This report examines the influence and impact of these changes on the behaviour and development of these markets, looking at the role and position of both the energy industry and customers. The report combines existing data with new research data collected during spring and summer 2006. Whilst the recency of the law changes, along with the simultaneous impact of other market variables limits the salience of any impact, the report nevertheless provides clear and interesting conclusions. In the electricity market, one major legislative change that came into force in the beginning of 2005 concerned the supervision of the reasonableness of electricity distribution pricing. According to the newly adopted ex ante regulation principles, the regulatory authority now determines the guidelines for reasonable pricing prior the start of a predefined regulatory period. So far, the price ...
Radiation-induced enteritis is a well-recognized sequel of therapeutic irradiation. Therefore we examined the radioprotective properties of Punica granatum peel extract (PPE) on the oxidative damage in the ileum. Rats were exposed to a single whole-body X-ray irradiation of 800 cGy. Irradiated rats were pretreated orally with saline or PPE (50 mg/kg/day) for 10 days before irradiation and the following 10 days, while control rats received saline or PPE but no irradiation. Then plasma and ileum samples were obtained. Irradiation caused a decrease in glutathione and total antioxidant capacity, which was accompanied by increases in malondialdehyde levels, myeloperoxidase activity, collagen content of the tissue with a concomitant increase 8-hydroxy-2'-deoxyguanosine (an index of oxidative DNA damage). Similarly, pro-inflammatory cytokines (TNF-?, IL-1? and IL-6) and lactate dehydrogenase were elevated in irradiated groups as compared to control. PPE treatment reversed all these ...
The passivity and breakdown of passivity of 1018 carbon steel in propylene carbonate (PC) and 1,2-dimethoxyethane (DME) mixtures with 0.5 molar lithium hexafluoroarsenate supporting electrolyte were examined via several electrochemical and surface analytical methods. The PC-DME/0.5 M LiAsF{sub 6} mixtures ranged from 10 to 90 mol % PC. The results from the PC/DME mixtures were compared to passivating mechanisms found in pure PC and DME solutions. In PC-rich mixtures, the breakdown of passivity occurred near the oxidation potentials of either organic solvent. Premature breakdown of the carbon steel in PC-DME mixtures occurred at sulfide inclusions as was observed earlier in PC/0.5 M LiAsF{sub 6} solutions although passive films attempted to form at these inclusion sites in mixtures containing at least 10 mol % DME. As the DME content increased in the PC-DME mixtures, the passive films formed on bare steel surfaces possessed an increasing polymer ...
Under appropriate conditions, bismuth molybdates can catalyze a number of transformations of olefins with selective oxidation being of particular importance. Experimental evidence suggests that the propylene is activated to an allylic species by a site associated with the Bi and that the oxidation step occurs at an Mo site. In order to address the mechanistic steps associated with these Mo sites. The authors discuss the chemistry of terminal oxo and imido groups. They find that for surface sites such as 1 about, 2 about and 3 about, the presence of two double bonds leads to a much more active species than those with a single multiple bond. This leads to a situation similar to that in olefin metathesis by high oxidation state Mo catalysis where the (spectator) oxo group species promotes formation of the metallacycle intermediate by formation of a partial Mo==O triple bond that stabilizes the intermediate. Calculations suggest that the magnitude of the spectator oxo activation is 35 kcal ...
Aging degradation is a phenomenon we all experience throughout life, both on a personal basis and in business. Many industries have been successful in postponing the inevitable impact on their related systems and components through programs to maintain long-term reliability, maintainability and safety. However, this has not always been the case for nuclear power. While all power plants are experiencing the world trend of increasing operating costs with age, few (if any) have been able to fully define the parameters that solve the aging equation, particularly in relation to major components. Inspection and preventive maintenance have not been effective in predicting life-limiting degradation and failure. In CANDU nuclear plants, utilities are taking a comprehensive approach in dealing with the aging problem. Programs have been established to identify the current condition and degradation mechanisms of critical components, the failure of which would impact negatively ...
In 1978, China's coal mining industry achieved an output of 618,000,000 metric tons of raw hard coal, an increase of 128,000,000 tons compared with 1977. This has been achieved primarily by increased new mine development and the modernizaion and expansion of existing mines. While 96% of China's coal is currently produced from underground mines, only 33% of this output is from full mechanized operations, i.e., mechanized longwall retreat faces. Over 1% is produced by hydraulic mining. The current Ten-Year Plan (1975-1985) established that the major thrust of new development and activity should be made particularly in the Shandong, Anhui, Henan, Guizhou, and Yunnan provinces. China is presently concentrating on the construction/enlargement of eight major coal mining centers, mainly in the north and northeast of the country, each with a designed capacity in excess of 10,000,000 tons a year. China has elected to import large ...
Small circular and noncircular channels are representative of flow passages in compact evaporators and condensers. This paper describes results of an experimental study on heat transfer to the flow boiling of refrigerant- 12 in a small circular tube of diameter = 2.46 mm. The objective of the study was to assess the effect of channel size on the heat transfer coefficient and to obtain additional insights relative to the heat transfer mechanisms. The flow channel was made of brass and had an overall length of 0.9 m. The channel wall was electrically heated, and temperatures were measured on the channel wall and in the bulk fluid stream. Voltage taps were located at the same axial locations as the stream thermocouples to allow testing over an exit quality range of 0.21 to 0.94 and a large range of mass flux (63 to 832 kg/m{sup 2}s) and heat flux (2.5 to 59 kW/m{sup 2}). Saturation pressure was nearly constant, averaging 0.82 MPa for most of the testing; a few test ...
When completed, Lawrence Livermore National Laboratory's (LLNL) National Ignition Facility (NIF) will be the world's largest laser with experimental capabilities applicable to stockpile stewardship, energy research, science and astrophysics. As construction of the conventional facilities nears completion, operations supporting the installation of specialized laser equipment have come online. Playing a critical role in the precision cleaning of mechanical parts from the NIF beamline are three pieces of aqueous cleaning equipment. Housed in the Optics Assembly Building (OAB), adjacent to NIF's laser bay, are the large mechanical parts gross cleaner (LMPGC), the large mechanical parts precision cleaner (LMPPC), and the small mechanical parts gross and precision cleaner (SMPGPC). These aqueous units, designed and built by Sonic Systems, Inc., of Newtown, ...
Radiotherapy can be very significant as the treatment for ocular lesions, eyes need to be preserved as properly as possible on their functions and cosmetics. The application of conventional X ray therapy has been gradually abandoned as conventional X ray therapy ceased to be accepted as the general treatment for malignant tumors. Consequently the necessity of electron beam therapy has been rising even as the substituted method for conventional X ray therapy. The department of radiology of Gunma University was obliged to establish a new therapy for ocular lesions, and has been trying electron beam therapy since 1973. It is concluded that electron beam therapy is not at all inferior to conventional X ray therapy as reported above. Basic therapeutic methods for ocular lesions are the following: 1) For epidermoid carcinoma, 600 rads at a time, 3600 - 4200 rads in total is applied by 8 MeV electron twice a week method. 2) For malignant melanoma, 1000 rads at a time, ...
The Executive Body adopted the Protocol on Heavy Metals on 24 June 1998 in Aarhus (Denmark). It targets three particularly harmful metals: cadmium, lead and mercury. According to one of the basic obligations, parties will have to reduce their emissions for these three metals below their levels in 1990. The Protocol aims to cut emissions from industrial sources, combustion process and waste incineration. It lays down strighten limit values for emissions from stationary sources and suggests best available techniques (BAT) for these sources, such as special filters or scrubbers for combustion sources or mercury-free processes. The Protocol requires parties to phase out leaded petrol. It also introduces measures to lower heavy metal emissions from other products, such as mercury in batteries, and proposes the introduciton of management measures for other mercury-containing products, such as electrical componets (thermostats, switches), measuring devices (thermometers, ...
The NATO Advanced Research Workshop on Nuclear Submarine Decommissioning and Related Problems was held in Moscow June 19--22, 1995. It was preceded by a visit to the Zvezdotchka Shipyard at Severodvinsk, a repair and maintenance yard for Russian nuclear submarines, for a subgroup of the workshop attendees. Most of the material in this paper is drawn directly form the workshop proceedings. Slightly less than 500 nuclear ships and submarines (the vast majority are submarines) have been constructed by the countries with nuclear navies. This includes approximately 250 by Russia, 195 by the United States, 23 by the United Kingdom, 11 by France and 6 by China. By the year 2000 it is expected that approximately one-half of these nuclear vessels will be removed from service and in various states of decommissioning. A newspaper account in June 1997 indicated that 156 Russian nuclear submarines had been removed from service. In August 1996 it was reported that 55 reactor compartment sections ...
This report, the ORNL Long-Range Environmental and Waste Management Plan, is the annual update in a series begun in fiscal year 1985. Its primary purpose is to provide a thorough and systematic planning document to reflect the continuing process of site assessment, strategy development, and planning for the current and long-term control of environmental issues, waste management practices, and remedial action requirements. The document also provides an estimate of the resources required to implement the current plan. This document is not intended to be a budget document; it is, however, intended to provide guidance to both Martin Marietta Energy Systems, Inc., and the US Department of Energy (DOE) management as to the near order of magnitude of the resources (primarily funding requirements) and the time frame required to execute the strategy in the present revision of the plan. As with any document of this nature, the near-term (one to three years) part of the plan is a pragmatic ...
Current hydrocarbon-based energy systems, current energy consumption and the push towards the utilization of renewable energy sources, fuelled by global warming and the need to reduce atmospheric pollution are discussed. The consequences of climatic change and the obligation of Annex B countries to reduce their greenhouse gas emissions in terms of the Kyoto Protocols are reviewed. The role that renewable energy sources such as hydrogen, solar and wind energy could play in avoiding the most catastrophic consequences of rapidly growing energy consumption and atmospheric pollution in the face of diminishing conventional fossil fuel resources are examined. The focus is on hydrogen energy as a means of storing and transporting primary energy. Some favorable characteristics of hydrogen is its abundance, the fact that it can be produced utilizing renewable or non-renewable sources, and the further fact that its combustion produces three times more energy per unit of mass ...
Inventories of emissions and removals of greenhouse gases will be used under the United Nations Framework Convention on Climate Change and the Kyoto Protocol to demonstrate compliance with obligations. During the negotiation process of the Kyoto Protocol it has been a concern that uptake of carbon in forest sinks can be difficult to verify. The reason for large uncertainties are high temporal and spatial variability and lack of representative estimation parameters. Additional uncertainties will be a consequence of definitions made in the Kyoto Protocol reporting. In the Nordic countries the national forest inventories will be very useful to estimate changes in carbon stocks. The main uncertainty lies in the conversion from changes in tradable timber to changes in total carbon biomass. The uncertainties in the emissions of the non-CO{sub 2} carbon from forest soils are particularly high. On the other hand the removals reported under the Kyoto Protocol will only be a ...
The Seismic Proving Test of Heavy Component with Energy Absorbing Supports has been conducted to prove the reliability of advanced seismic technology, supporting heavy component such as PWR steam generator with large capacity energy absorbing supports under the sponsorship of Ministry of Economical Trade and Industry. If energy absorbing supports are adopted for NPP heavy components, support structure of facility will be much simplified due to their seismic energy absorbing effect. The paper describes the results of lead damper element test and seismic test at Tadotsu Laboratory, using 1/2.5 scale PWR Steam Generator model supported by Lead Extraction Damper (LED) and development of characteristics evaluation formula of energy absorbing support. (author)
The proposed device incorporates an axle which has a roller bearing support mounted upon it. This support uses a cylindrical sleeve that comes in contact with the housing, the sensors, and the bearing support component. Metering accuracy is improved by placing roller bearing supports into grooves running through the protruding center sections of the sensor elements. These roller bearing supports interface with the cylindrical sleeve.
Silicon carbide (SiC) based electronic devices are of great importance for applications under the condition of high temperature, high power and high radiation. Schottky diodes of Palladium/SiC are good candidates for hydrogen and hydrocarbon gas sensors at elevated temperature. The detection sensibility of the diodes has been found heavily temperature dependent. In this work, the electrical and chemical properties of Pd/SiC Schottky contacts were studied by XPS and AES at different annealing temperatures. Schottky diodes were made by depositing ultra-thin palladium films onto a silicon carbide substrate. No significant change in the Schottky barrier height of the Pd/SiC contact was found in the temperature range of 300-673K. Palladium diffusion into SiC and the formation of palladium silicides were observed at room temperature and became significant at 300^oC and higher temperature. The mechanism of diffusion and reaction at the Pd/SiC interface will be discussed. ...
Vanadium alloys exhibit important advantages as a candidate structural material for fusion first wall/blanket applications. These advantages include fabricability, favorable safety and environmental features, high temperature and high wall load capability, and long lifetime under irradiation. Vanadium alloys with (3-5)% chromium and (3-5)% titanium appear to offer the best combination of properties for first wall/blanket applications. A V-4Cr-4Ti alloy is recommended as the reference composition for the ITER application. This report provides a summary of the R&D conducted during 1994 in support of the ITER Engineering Design Activity. Progress is reported for Vanadium Alloy Production, Welding, Physical Properties, Baseline Mechanical Properties, Corrosion/Compatibility, Neutron Irradiation Effects, Helium Transmutation Effects on Irradiated Alloys, and the Status of Irradiation Experiments. Separate abstracts have been prepared for ...
A stochastic-convective reactive (SCR) transport method is developed for one-dimensional steady transport in physically heterogeneous media with nonlinear degradation. The method is free of perturbation amplitude limitations and circumvents the difficulty of scale dependence of phenomenological parameters by avoiding volume-averaged specifications of diffusive/dispersive fluxes. The transport system is conceptualized as an ensemble of independent convective-reactive streamlines, each characterized by a randomized convective velocity (or travel time). Dispersive effects are treated as a component of the randomness in the streamline velocity ensemble, so no explicit expression for hydrodynamic dispersive flux is written in the streamline transport equation. The expected value of the transport over the stream tube ensemble is obtained as an average of solutions to the reactive convection equation according to the stream tube (travel time) probability distribution function. In this way, ...
A splice assembly tool for assembling component parts of an electrical conductor while producing a splice connection between electrical cables therewith, comprises a first structural member adaptable for supporting force applying means thereon, said force applying means enabling a rotary force applied manually thereto to be converted to a longitudinal force for subsequent application against a first component part of said electrical connection, a second structural member adaptable for engaging a second component part in a manner to assist said first structural member in assembling the component parts relative to one another and transmission means for conveying said longitudinal force between said first and said second structural members, said first and said second structural members being coupled to one another by said transmission means, wherein at least one of said component parts comprises a tubular elastomeric sleeve and said force applying means provides a ...
A probability-based approach is presented as the integration of probabilistic methods and deterministic modelling based on the finite element method. An existing finite element software package was linked to an existing probabilistic package to analyse the complex mechanics that occur during the transient non-linear analysis of impact problems. This methodology is applied to a pipe whip analysis of a group-distribution-header, which results from a guillotine break, and subsequent impact with the adjacent building wall; this is a postulated accident for the Ignalina Nuclear Power Plant RBMK-1500 reactors. The uncertainties of material properties, component geometry data and loads were taken into consideration. The probabilities of failure of the impacted header and of the header support-wall were estimated given uncertainties in material properties, geometrical parameters and loading. The software ProFES was used for the probabilistic analysis ...
The hydro-generators suffer during its operative useful life a combination of stresses of nature thermal, electric, mechanics and environmental. With the time, they are going losing the capacity to support those stresses and the power plants suffer, more and more frequently, undesirable stops for repair services and maintenance. In function of the high costs incurred with these stopped, the operation of the power plant can be economically impracticable. That unavailability of the generation for the electric system, it results in reduction of the reliability, burdening the politics of load ruling. The re-potentiation is a proposal that seeks to extend the useful life of hydro-generators, at the same time that it try to rescue the reliability and the readiness of the plant, with larger power. The power increase is usually made possible, or for the surplus of the hydro resources in excess, or for the reduction of the losses of all the components ...
We summarize results of recent studies of heavy quarkonia correlators and spectral functions at finite temperatures from lattice QCD and systematic T-matrix studies using QCD motivated finite-temperature potentials. We argue that heavy quarkonia dissociation shall occur in the temperature range $1.2 \\le T_d/T_c \\le 1.5$ by the interplay of both screening and absorption in the strongly correlated plasma medium. We discuss these effects on the quantum mechanical evolution of quarkonia states within a time-dependent harmonic oscillator model with complex oscillator strength and compare the results with data for $R_{\\rm AA}/R_{\\rm AA}^{\\rm CNM}$ from RHIC and SPS experiments. We speculate whether the suppression pattern of the rather precise NA60 data from In-In collisions may be related to the recently discovered X(3872) state. Theoretical support for this hypothesis comes from the cluster expansion of the plasma Hamiltonian for heavy ...
CERN signed a Co-operation Agreement with the Government of Pakistan in 1994, which was followed in 1997 by a Protocol signed with the Pakistan Atomic Energy Commission (PAEC) concerning CMS magnet supports. CERN and PAEC then signed in 1998 a Memorandum of Understanding for collaboration in the construction of the CMS detector. The participation by Pakistani scientists and engineers in the CERN programme is channelled through the National Centre of Physics (NCP) established at the Quaid-i-Azzam University in Islamabad, under the terms of a 1999 Protocol to the 1994 Co-operation Agreement. The engineering and detector construction work performed under these Agreements has been of high quality, and the Pakistani participation is valued highly by the CMS collaboration. In continuation of this co-operation, Pakistan, represented by PAEC as funding agency, has now proposed to make in-kind contributions to the LHC Project, such as mechanical ...
Although the mechanism is unknown, Calculus Bovis and its active components, cholic acid analogs (CAAs), have been used in China to treat a wide range of diseases. Based on the previous finding that the potency of CAA is strongly dependent on the intrinsic surface activity, this paper aimed to investigate the role of the plasma membrane in the pharmacological activity of CAAs. First, CAAs (0.1 mM) caused a surface activity-dependent depression on ATPase activity in the cell membrane extract, but it had no effects on other cellular extracts, suggesting an indispensable role of the membrane environment for pharmacological activity. Second, CAAs lowered the membrane fluidity of cultured Caco-2 cells with the same rank-order of potency sequence. Third, the hypothesis that any functional protein located on the membrane is influenced by changes in cellular membrane fluidity was supported by: ileal contraction that was induced by acetylcholine and ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for ...
The Boiler and Pressure Vessel Code (BPVC) of the American Society of Mechanical Engineers (ASME) has introduced a risk based approach into Section XI that covers Rules for Inservice Inspection of Nuclear Power Plant Components. The risk based approach requires application of the probabilistic risk assessments (PRA). Because no industry consensus standard existed for PRAs, ASME has developed a standard to evaluate the quality level of an available PRA needed to support a given risk based application. The paper describes the PRA standard, Section XI application of PRAs, and plans for broader applications of PRAs to other ASME nuclear codes and standards. The paper addresses several specific topics of interest to Section XI. Important consideration are special methods (surrogate components) used to overcome the lack of PRA treatments of passive components in PRAs. The approach allows calculations of conditional core damage probabilities both for ...
The work reported here encompasses analyses of specific potential spill scenarios for oil exploration activity planned offshore of Namibia. The analyses are carried out with the SINTEF Oil Spill Contingency and Response (OSCAR) 3-dimensional model systems. A spill scenario using 150 m{sup 3} of marine diesel demonstrates the rapidity with which such a spill will dissipate naturally, even in light winds. Vertical and horizontal mixing bring subsurface hydrocarbon concentrations to background levels within a few days. A hypothetical 10 day blowout scenario releasing 11,000 bbl per day of light crude oil is investigated in terms of the potential for delivering oil to selected bird and marine mammal areas along the Namibian coast. Worst case scenarios are selected to investigate the potential mitigating effects of planned oil spill response actions. Mechanical recovery significantly reduces, and in some cases eliminates, potential environmental consequences of these ...
Although the subtrate binding properties of adenylate kinase (AK) have been studied extensively by various biochemical and biophysical techniques, it remains controversial whether uncomplexed adenosine 5'-triphosphate (ATP) binds to the adenosine 5'-monophosphate (AMP) site of AK. The authors present two sets of experiments which argue against binding of ATP to the AMP site. (a) /sup 31/P nuclear magnetic resonance titration of ATP with AK indicated a 1:1 stoichiometry on the basis of changes in coupling constants and line widths. This ruled out binding of ATP to both sites. (b) ATP and MgATP were found to behave similarly by protecting AK from spontaneous inactivation while AMP showed only a small degree of protection. Such inactivation could also be protected or reversed by dithioerythritol and is most likely due to oxidation of sulfhydryl groups, one of which (cysteine-25) is located near the MgATP site. The results support binding of ATP to ...
Currently, high temperature filter systems are in the demonstration phase with the first commercial scale hot filter systems being installed on integrated gasification combined cycle (IGCC) and pressurized fluid bed combustion cycle (PBFC) systems (70 MW). They are dependent on the development of durable and economic high temperature filter systems. These filters are mostly ceramic tubes or candles. Ceramic filter durability has not been high. Failure is usually attributed to mechanical or thermal shock: they can also undergo significant changes due to service conditions. The overall objective of this project is to commercialize weldable, crack resistant filters which will provide several years service in advanced power processes. The specific objectives of this project are to develop corrosion resistant alloys and manufacturing processes to make Iron Aluminide filter media, and to use a ``short term`` exposure apparatus supported by other ...
A single plasma process involving three consecutive steps has been developed for producing high gas flow catalytic nanostructures on the electrodes of proton exchange membrane (PEM) fuel cells (FC). Using a high density helicon radio frequency (13.56 MHz) plasma, nickel is sputtered onto a porous carbon support. Changing the background gas from argon to methane/hydrogen allowed 2 ?m long, 37 nm diameter carbon nanofibres (CNFs) to be grown by diffusion through the nickel clusters in a 'tip growth' mechanism at the relatively low temperature of 400 deg. C. The third step involves plasma sputtering of platinum onto the CNFs, resulting in nanoclusters (3-8 nm) being formed on the periphery of the CNFs. Four FC cathodes were synthesized on carbon paper and PTFE/carbon loaded cloth (known as gas diffusion layer, GDL), both with and without CNFs, with the Pt/CNFs nanostructures grown on PTFE/carbon loaded cloth having the best FC performances. ...
This document establishes the Quality Assurance (QA) Program requirements for the Hazards Waste remedial Actions Program (HASWRAP) for ensuring, with a high degree of confidence, that program objectives will be achieved as planned. The QA Program is introduced in Sect. 1. The HAZWRAP Support Contractor Office (SCO) functional organization and QA responsibilities are shown in Sect. 2. QA program requirements are contained in Sect. 3. These requiremens are pased on the American national Standard, American National Standards Institute/American Society of Mechanical Engineers NQA-1 Quality Assurance Program Requirements for Nuclear Facilities. The 18 elements defined in the standard are tailored to HAZWRAP's needs. The QA program requirements are delineated under the major headings: Quality Assurance Program, Organization, and Control of Quality;two additional program requirements, Software Quality Assurance and Problem Prevention, are included. ...
Using a sample of 88 less developed countries, hypotheses were tested over time in panel regression models to determine what type of impact military and arms expenditures have on national economic growth and development. Hypotheses were drawn from three theoretical perspectives. The first set of tested hypotheses came from the modernization literature, which assumes that expenditures have positive ripple effects in national economies that are good for growth and development. The second set is based on the economic dependency and world systems theories. These theories assume that the relationships between countries affect a nation's economic structure and that arms expenditures are a mechanism used by core industrialized nations to increase economic penetration and dependency of periphery unindustrialized countries. Finally, the third set of hypotheses is grounded in literature on the role of the state in development. Briefly, it is assumed that military ...
This document presented the results of a full-scale pile load tests conducted on helix pile foundations supporting power transmission towers in northern Manitoba. The site conditions were described along with pile installation and the performance of the foundations. The pile load tests were carried out in 2 different soil conditions, notably soft to firm clays and stiff high plastic clays with silt varves. The performance of the helix pile foundations were examined under axial compressive and axial tension (uplift) loading conditions. The results of the compressive load tests were presented in the form of load settlement curves while the results of the uplift load tests were presented in the form of load displacement curves. Both types of load tests in soft or stiff clays showed the suitability of helical pile foundations for power transmission lines in northern Manitoba. The cylindrical shear failure mechanism controlled the behaviour of ...
The role of intermediate products of dioxygen reduction in cytotoxic effects ascribed to oxygen molecules was studied in vivo using various yeast mutants with changed response to oxygen stress. It has been documented that superoxide radical exerts its deleterious effects on yeast cells directly and the role of other oxygen species derived from it is hardly detectable. Yeast Saccharomyces cerevisiae, however, cannot be considered as a typical eukaryotic organism due to its inability of synthesizing polyunsaturated fatty acids (pufa). These fatty acids are known as main target molecules during oxidative stress and their peroxidation leads to cytotoxic effects. As fatty acid content could be easily manipulated in yeast, this organism was used to evaluate the contribution of pufa peroxidation process to the cytotoxic effects of oxygen. Results obtained show, that yeast cells containing linolenic acid as the main constituent of phospholipids are hypersensitive to oxygen stress and, ...
45{number_sign} steel, which has good mechanical strength and is relatively cheap, is a common constituent in industrial components, such as precision gears, piston columns of oil pumps, and so on. However, since the working environment of these industrial parts is sometimes quite harsh and unforgiving, they are vulnerable to wear and corrosion. Replacing 45{number_sign} steel with stainless or alloy steel increases the cost significant, and a better alternative is to improve its surface properties and lifetime using plasma immersion ion implantation (PIII). The authors have devised a variety of treatment processes using PIII, including radio-frequency (RF) plasma nitriding, RF plasma nitriding and nitrogen PIII, Ti deposition in conjunction with nitrogen PIII (IBED), as well as Cr deposition followed by nitrogen PIII (IBED). To assess the efficacy of the processes, the microhardness and mass loss due to wear were measured for both the untreated and treated ...
Nanowires of copolymers film based on aniline and 1-amino-2-naphthol-4-sulphonic acid were electrochemically synthesized on the iron electrode by cyclic voltammetry using oxalic acid as a supporting electrolyte. Protective properties of copolymer film on the iron surface in 1.0 M HCl solution was investigated by chronoamperometry, potentiodynamic polarization technique and electrochemical impedance spectroscopy (EIS). The results showed that the copolymer film showed the significant shifting in the corrosion potential and greater charge transfer resistance. Moreover, the copolymer showed the larger degree of surface coverage onto the iron surface, reflecting the higher protection for corrosion of the iron in acidic medium. In addition, the film constitutes a physical as well as a chemical barrier layer due to the presence of -OH and -NH groups in ANSA unit, which provides passivity protection in polymer coatings. The mechanism of corrosion ...
This paper describes the test results on high-temperature strength properties of fire resistant steel(FR steel) for building, the formulation, and the examples of application to member tests and actual buildings. Because of its components and manufacturing method, FR steel excels in strength at elevated temperature due to precipitation and dispersion strengthening. Tests on high temperature properties of FR steel showed that every property such as strength, stress-strain curve, elastic modulus, and creep performance at high temperature was superior to those of conventional steels. Then, it was confirmed in the tensile tests at room temperature and high temperature after heat history that FR steel could be reused after fire. It was also found in the member tests that columns and beams of FR steel could support loadings equivalent to long-term allowable unit stress until the temperature rose up to 600 centigrade. Moreover, test results could be simulated by the ...
Tantalum and tantalum-based thin films have gained precedence as the diffusion barrier for copper interconnects used in the latest generation of integrated circuits (ICs). The paper presents insight and observations on the covariance of texture and grain size of wrought tantalum sputtering targets and their influence on sputtering performance. Previous studies involving deposition trials of tantalum targets of varying metallurgical character had demonstrated that both grain size and textural homogeneity is critical for assuring reliable sputtering performance of tantalum. Subsequently, a model had been proposed to prescribe how localized texture bands and orientation clusters in tantalum are effectively resistant to sputter erosion. In this paper, results of atomic force microscopy (AFM) and orientation imaging microscopy (OIM{sup TM}) analyses on the eroded surface of a tantalum sputtering target are presented. Initial findings support the model's ...
Increases in atmospheric CO[sub 2] are predicted to cause an increase in the C:N ratio of plant substrates entering the soil organic matter pool. We experimentally increased soil C:N ratios by adding 40 g C/m[sup 2] as sucrose (metabolic C) or cellulose (structural C) in short-, mid-, and tall-grass plots in the Serengeti Ecosystem, and measured plant productivity, plant nutrient uptake rates, and mineralization rates. Experimental treatments also included fencing to exclude grazing and additions of 40 g N/m[sup 2] as urea to simulate a urine hit from an average-sized ungulate. Productivity was only 60% of controls in C-addition plots, and was similar for sucrose and cellulose. However, this response was not observed in the short-grass site, an area of relatively low rainfall and high fertility. These results support the role of a plant-microbe negative feedback mechanism on plant growth in which increased C to microbes results in increased ...
Cyclopropane isomerization to propylene over various Eu[sup 3+] loadings in NaX zeolite have been studied by measurements of steady-state and transient kinetics and by Fourier transform infrared spectroscopy. As Eu[sup 3+] loading increases, the rate of deactivation increases, the conversion increases, apparent activation energies are lowered, and Bronsted acid site strength and amounts increase. Apparent activation energies of 13-15 kcal/mol for propylene formation have been observed for these systems, consistent with literature reports for other metal supported heterogeneous catalyst systems. Deactivation studies have shown that activity can be restored by heating in He at 380[degrees]C between various temperature runs, and that gases desorbed during regeneration are predominantly propylene. Poisoning studies of Bronsted sites with Na vapor lead to deactivation of these catalysts. A reaction mechanism scheme based on [pi] allyl intermediates ...
For a better understanding of sulphidation mechanisms, some alloys (alloy 600, alloy 800, Uranus S, iron-chromium-aluminium-alloy) and metals (iron, chromium, nickel, molybdenum, titanium) were tested at 773, 873, 1 073 K in gaseous sulphur dioxide. Total pressure was 760 torrs. Sulphur dioxide pressure was 760, 100 and 10 torrs. Argon, oxygen, water vapor were used, successively, as pressure complement. Oxygen supply, generally speaking cause decay of corrosion resistance in SO/sub 2/ atmospheres especially at 1 073 K with low ratio p/sub O2//P/sub SO/sub 2//. Water vapor supply act similarly. Temperature laws and pressure laws do not give monotonous rise of corrosion values. There are maximas suggesting corrosion products undertaking a volatilization process. According to test conditions, Uranus S, chromium, alloy 800 (and titanium at some extent) showed good corrosion resistance. That results are supporting those obtained by JRC Ispra team, ...
Efflux of dopamine through the dopamine transporter (DAT) is critical for the psychostimulatory properties of amphetamines, but the underlying mechanism is unclear. Here we show that Ca(2+)/calmodulin-dependent protein kinase II (CaMKII) plays a key role in this efflux. CaMKIIalpha bound to the distal C terminus of DAT and colocalized with DAT in dopaminergic neurons. CaMKIIalpha stimulated dopamine efflux via DAT in response to amphetamine in heterologous cells and in dopaminergic neurons. CaMKIIalpha phosphorylated serines in the distal N terminus of DAT in vitro, and mutation of these serines eliminated the stimulatory effects of CaMKIIalpha. A mutation of the DAT C terminus impairing CaMKIIalpha binding also impaired amphetamine-induced dopamine efflux. An in vivo role for CaMKII was supported by chronoamperometry measurements showing reduced amphetamine-induced dopamine efflux in response to the CaMKII inhibitor KN93. Our data suggest that ...
The failure of the standard Growth Approach to economic development to solve the problems of underdevelopment in LDCs has caused an alternative approach, Basic Needs Approach (BNA), to attain prominence in development thought. BNA emphasizes poverty-minimizing growth. Its strategy of direct attack on poverty has better potential for LDCs' development and fulfillment of their populations' basic needs than the trickle-down mechanism of the Growth Approach. BNA requires, among other things, (a) suitable rural financial markets (RFMs) as parts of the overall financial system, and (b) indigenous technological capabilities. The financial system, if it functions as a central element in an institutionalized technology policy, can link technology-related institutions that generate, evaluate, and promote appropriate technologies (ATs) with RFMs that can support adoption and diffusion of ATs in the agro-rural sector. The above argument ...
The United States and Russia have agreed to jointly develop a solar dynamic (SD) system for flight demonstration on the Russian Mir space station starting in late 1997. Two important components of this SD system are the solar concentrator and heat receiver provided by Russia and the US, respectively. This paper describes optical analysis of the concentrator and solar flux predictions on target receiver surfaces. The optical analysis is performed using the code CIRCE2. These analyses account for finite sun size with limb darkening, concentrator surface slope and position errors, concentrator petal thermal deformation, gaps between petals, and the shading effect of the receiver support struts. The receiver spatial flux distributions are then combined with concentrator shadowing predictions. Geometric shadowing patterns are traced from the concentrator to the target receiver surfaces. These patterns vary with time depending on the chosen Mir flight attitude and ...
The cross sections for /sup 250/Fm, /sup 244-246/Cf, /sup 242-244/Cm, and /sup 242/Am/sup g-italic/ produced by the /sup 12/C+ /sup 242/Pu and the /sup 16/O+ /sup 238/U reactions leading to the same compound nucleus of /sup 254/Fm have been measured by using radiochemical methods. The excitation functions show that the difference between the /sup 12/C+ /sup 242/Pu and the /sup 16/O+ /sup 238/U reactions can be attributed mainly to the Coulomb barriers. Our results were compared with others reported previously for /sup 22/Ne+ /sup 232/Th, /sup 12/C+ /sup 238/U, /sup 12/C+ /sup 240,241/Pu, /sup 13/C+ /sup 241/Pu, /sup 16/O+ /sup 233/U, and /sup 16/O+ /sup 242/Pu reaction systems, and support a mechanism involving transfer of ..cap alpha..-particle clusters (C,Be,He) from projectile to target for the production of Cf and Cm isotopes.
The cross sections for /sup 250/Fm, /sup 244-246/Cf, /sup 242-244/Cm, and /sup 242/Am/sup g/ produced by the /sup 12/C+ /sup 242/Pu and the /sup 16/O+ /sup 238/U reactions leading to the same compound nucleus of /sup 254/Fm have been measured by using radiochemical methods. The excitation functions show that the difference between the /sup 12/C+ /sup 242/Pu and the /sup 16/O+ /sup 238/U reactions can be attributed mainly to the Coulomb barriers. Our results were compared with others reported previously for /sup 22/Ne+ /sup 232/Th, /sup 12/C+ /sup 238/U, /sup 12/C+ /sup 240,241/Pu, /sup 13/C+ /sup 241/Pu, /sup 16/O+ /sup 233/U, and /sup 16/O+ /sup 242/Pu reaction systems, and support a mechanism involving transfer of #alpha#-particle clusters (C,Be,He) from projectile to target for the production of Cf and Cm isotopes.
On 24th of July 2007 Westinghouse Electric Co. signed landmark contracts with China's State Nuclear Power Technology Corporation (SNPTC), to provide four AP1000 nuclear power plants in China. The AP1000 is a two-loop 1117 MWe Pressurized Water Reactor (PWR). It is based on proven technology, but with an emphasis on safety features that rely on natural driving forces, such as pressurized gas, gravity flow, natural circulation flow and convection. Ansaldo Nucleare has provided a significant support to the passive plant technology development and, starting from 2000, is cooperating with Westinghouse to development of the AP1000 Plant. In the frame of the AP1000 Chinese agreement, Ansaldo Nucleare, in Joint Venture with Mangiarotti Nuclear, has signed a contract with Westinghouse for the design and the supply of innovative components to be installed in the first AP1000 unit to be constructed at the Sanmen site. The contract includes: the design of the steel containment ...
Development in organic farming has been stimulated by farmers and consumers becoming interested in healthy food products and sustainable environment. Organic agriculture is a holistic production management system which is based on the principles of health, ecology, care, and fairness. Organic development in Uganda has focused more on the crop sector than livestock sector and has primarily involved the private sector, like organic products export companies and non-governmental organizations. Agriculture in Uganda and many African countries is predominantly traditional, less mechanized, and is usually associated with minimum use of chemical fertilizers, pesticides, and drugs. This low external input agriculture also referred to as "organic by default" can create basis for organic farming where agroecological methods are introduced and present an alternative in terms of intensification to the current low-input/low-output systems. Traditional farming should not be ...
Twenty undergraduate students participated in an elaborative learning test to evaluate the relationship between electrical brain activity and subsequently recalled and not-recalled words. Data collected from the midline (Fz, Cz, Pz) and lateral scalp sites (F3, F4, C3, C4, P3, P4) were analysed. The difference between event-related potentials (ERPs) elicited by subsequently recalled and not-recalled words, the ERP memory effect, was evaluated for each portion (primacy, plateau and recency) of the serial-position curve (SPC). We compared peak amplitudes for the P1, N1, P2, N400, P3 and frontal positive slow wave (FPSW) components. The electrophysiological data support the hypothesis that different mechanisms underlie primacy and recency effects during free recall paradigms. There was no support for the hypothesis that an association arises between memory and the FPSW when subjects utilise elaborative learning strategies. The ...
Studies on the determinants of pain-related support are needed to enhance couples-based treatments for pain. The purpose of this study was to determine the extent to which pain catastrophizing...Full Text Available
Using a theoretical framework of social support, and content analysis, the content and pattern of support in messages posted in a 4-week period on a commercial health network for individuals concerned...Full Text Available
A device is presented with handle containing hinges and work support arm, a flexible pin with supports and extra weights. The flexible pin is equipped with cantilevered sergments and weights. The bracket hinges on the handle are perpendicular to the axis of the flexible pin. To reduce handle vibration during drilling hard rock, the handle and brackets are joined to allow relative movement on the surface perpendicular to the hinges of the work support arm. The handle is joined to the work support arm parallel to the sides and the work support arm has holes to accomodate this. Elastic bushings are located between the lateral sides of the work support arm where it is joined to the handle.
... Headquarters Element, Defense Logistics Agency, Support Detachment 3 ... Joint Task Force, Team 6 ... 19th Special Forces Group, Support Element 1 ...
OBJECTIVEEvaluate the qualitative and quantitative differences between moderated and unmoderated on-line social support groups focused on asthma.DESIGNA...Full Text Available
This paper reports an investigation of older adults' needs and preferences concerning online social support. We focused our analysis on seven different aspects of online support: Self disclosure, Deep support, Light support, Community building, Information/Facts, Off topic, and Technical issues. For each aspect we were interested in how older adults perceive this aspect of support, what they think are the similarities and differences of this aspect of support in online settings vs offline settings, and what they perceive are the advantages and disadvantages of communicating this aspect of support online. We did this by conducting detailed interviews with three groups of older adults (31 people in total) with different levels of expertise in using the internet and online communication (olde...
... s guides and "how-to" videos and other materials, and 7. Receive continuing support from GLOBE's ... and educational materials that result from international proposals in its materials and support ...
The temperature dependent vibrational relaxation of the CO stretching mode of Rhodium dicarbonyl acetylacetonate (Rh(CO){sub 2}(acac)) and tungsten hexacarbonyl (W(CO){sub 6}) in dibutylphthalate (DBP) and 2-methylpentane (2-MP) were measured with IR pump and probe (P-P) experiments. The experiments were performed with {approximately}1.5 ps pulses generated by the Stanford superconducting accelerator pumped free electron laser (FEL). Measurements were performed on the Rh(CO){sub 2}(acac) CO asymmetric stretching mode at {lambda} = 4.98{mu}m from 10 K to 300 K. Both the parallel and magic angle probe polarizations decay curves are biexponential over the entire temperature range. The slow component (ranging from 40 ps at 300 K to 55 ps at 10K) is attributed to the population relaxations. For the fast component (ranging from 4-5 ps at 300 K to 13-15 ps at 10K), we propose a mechanism of spectral diffusion, in contrast to the previously proposed ...
The Plant Life Assessment Network (PLAN) is a Brite Euram Type II Thematic Network, initiated by the European Commission to facilitate structured co-operation between all cost shared action projects already funded by the Commission which fall under this common technical theme. The projects involved address a multiplicity of problems associated with plant life assessment and are drawn from Brite-Euram, Standards, Measurement and Testing, Nuclear Fission Safety and Esprit EC programmes. The main aim of the Network is to initiate, maintain and monitor a fruitful co-operation process between completed, ongoing and future EC R and D projects, thereby promoting improved cross fertilization and enhanced industrial exploitation of R and D results. As the project is in its infancy, this presentation covers the background to the initiative in some detail. In particular two key aspects are highlighted, namely, the requirement of the EC to launch such a network in the area of plant life assessment ...
Mechanical testing of controlled-purity Ni-xCr-9Fe-yC alloys at 360 C revealed an environmental enhancement in IG cracking and time-dependent deformation in high purity and primary water over that exhibited in argon. Dimples on the IG facets indicate a creep void nucleation and growth failure mode. IG cracking was primarily located at the interior of the specimen and not necessarily linked to direct contact with the environment. Controlled potential CERT experiments showed increases in IG cracking as the applied potential decreased, suggesting that hydrogen is detrimental to the mechanical properties. It is proposed that the environment, through the presence of hydrogen, enhances IG cracking by enhancing the matrix dislocation mobility. This is based on observations that dislocation-controlled creep controls the IG cracking of controlled-purity Ni-xCr-9Fe-yC in argon at 360 C and grain boundary cavitation and sliding results that show the ...
The IRG protein Irgm3 preserves cell survival during coxsackievirus B3 (CVB3) infection. However, the molecular mechanisms are not clear. Here, we examined the effect of Irgm3 expression on ER stress triggered by pharmacological agents or CVB3 infection. In Tet-On/Irgm3 HeLa cells, Irgm3 expression suppressed either chemical- or CVB3-induced upregulation of glucose-regulated protein78. Further, Irgm3 strongly inhibited the activation of both the PERK and ATF6 pathways of ER stress responses, which further led to the diminished phosphorylation of eIF2?, reduced cleavage/activation of transcription factor SREBP1 and attenuated induction of proapoptotic genes CHOP and GADD34. These data were further supported by experiments using Irgm3 knockout mouse embryonic fibroblasts, in which the ER stress induced by CVB3 was not relieved due to the lack of Irgm3 expression. In addition, the tunicamycin-triggered ER stress promoted the subsequent CVB3 ...
A processing technique for A-15 compounds which has improved mechanical and superconducting properties has been developed. This technique consists of rapid solidification of the alloy by the chill block spinning machine (CBSM) to form amorphous ribbons and by subsequent annealing crystallizes the stable or metastable fine grain flexible A-15 structure. The CBSM has been modified so that all the processing parameters could be controlled and optimized for each alloy composition. By the improved CBSM it was possible to form amorphous Nb_3Si, Nb_3Ge and Nb_3(AlSi) ribbons with more than 80% reproducible rate. Critical current density measurements are limited by contact resistance. A Cu plating technique was introduced in this research that made the contact resistance three orders of magnitude lower than that obtained by other methods. This plated coating also gave an additional mechanicalsupport to the sample and acted as a ...
A processing technique for A-15 compounds which has improved mechanical and superconducting properties has been developed. This technique consists of rapid solidification of the alloy by the chill block spinning machine (CBSM) to form amorphous ribbons and by subsequent annealing crystallizes the stable or metastable fine grain flexible A-15 structure. The CBSM has been modified so that all the processing parameters could be controlled and optimized for each alloy composition. By the improved CBSM it was possible to form amorphous Nb{sub 3}Si, Nb{sub 3}Ge and Nb{sub 3}(AlSi) ribbons with more than 80% reproducible rate. Critical current density measurements are limited by contact resistance. A Cu plating technique was introduced in this research that made the contact resistance three orders of magnitude lower than that obtained by other methods. This plated coating also gave an additional mechanicalsupport to the sample ...
The research carried out in Canada in the design of containers for the disposal of radioactive waste has focussed on spent nuclear fuel, even though the quantities of other currently stored radioactive wastes are substantially greater. Research carried out at the Royal Military College of Canada on the effects of mixed fields of radiation on high polymer adhesives and composite materials has shown that some polymers are quite resistant to radiation and could well serve in the fabrication of radioactive waste disposal containers. The purpose of this research was to determine if thermoplastic polymers could be used as superior materials to replace metals in the application of low and intermediate level radioactive waste disposal containers. Polymers have the advantage that they do not corrode like metals. The experimental methods, used in this research, focused on the effects of radiation on the properties of the materials. Polypropylene, Nylon 66, Polycarbonate, and Polyurethane, with ...
This study identifies potential applications and design requirements for ceramic materials (CMs) and ceramic composite materials (CCMs) in the NGNP hightemperature gas-cooled reactor (HTGR) primary circuit. Components anticipated for fabrication from non-graphite CMs and CCMs are identified along with recommended normal and off-normal operating conditions. The evaluation defines required dimensions and material properties of the candidate materials for normal operating conditions (NOC), anticipated transients, abnormal events, and design basis events. The report also identifies additional activities required for codifying the selected materials. The activities include ASTM Standard and ASME Code development and other work to support NRC licensing of the plant. Evaluation of the NGNP baseline design indicates components requiring either CMs or CCMs depend upon the reactor operating temperatures. For a reactor outlet temperature of 900 oC, four of the five evaluated ...
The effects of the dopants, Mg{sup 2+}, Ca{sup 2+}, Sr{sup 2+}, Sc{sup 3+}, Yb{sup 3+}, Y{sup 3+}, Gd{sup 3+}, La{sup 3+}, Ti{sup 4+}, Zr{sup 4+}, and Nb{sup 5+}, on the grain boundary mobility of dense CeO{sub 2} have been investigated from 1,270 to 1,420 C. Parabolic grain growth has been observed in all instances. Together with atmospheric effects, the results support the mechanism of cation interstitial transport being the rate-limiting step. A strong solute drag effect has been demonstrated for diffusion-enhancing dopants such as Mg{sup 2+} and Ca{sup 2+}, which, at high concentrations, can nevertheless suppress grain boundary mobility. Severely undersized dopants (Mg, Sc, Ti, and Nb) have a tendency to markedly enhance grain boundary mobility, probably due to the large distortion of the surrounding lattice that apparently facilitates defect migration. Overall, the most effective grain growth inhibitor at 1.0% doping is Y{sup 3+}, while ...
The Kyoto Protocol attempts through political negotiations to guide participating industrialized countries' greenhouse gas (GHG) emissions from a positive growing trend, to reach a peak point (or turning point), and then be reduced to a negative growth. That means the relationship between decreasing GHG emissions and economic growth may be described by an inverted-U curve (or called a bell-shaped curve), which is consistent with the concept of the Environmental Kuznets Curve (EKC) hypothesis. This research observed that the economic development and GHG emissions in Economies in Transition (EITs) exhibit a hockey-stick curve trend (or called quasi-L-shape curve), that also generates a lot of 'hot air' which is significant to the implementation of the Kyoto Protocol. In addition, through the analysis of single-country time series data and GDP data, this research demonstrated that statistical data for most of the Annex II countries do not possess evidence that ...
The Kyoto Protocol attempts through political negotiations to guide participating industrialized countries' greenhouse gas (GHG) emissions from a positive growing trend, to reach a peak point (or turning point), and then be reduced to a negative growth. That means the relationship between decreasing GHG emissions and economic growth may be described by an inverted-U curve (or called a bell-shaped curve), which is consistent with the concept of the Environmental Kuznets Curve (EKC) hypothesis. This research observed that the economic development and GHG emissions in Economies in Transition (EITs) exhibit a hockey-stick curve trend (or called quasi-L-shape curve), that also generates a lot of 'hot air' which is significant to the implementation of the Kyoto Protocol. In addition, through the analysis of single-country time series data and GDP data, this research demonstrated that statistical data for most of the Annex II countries do not possess evidence that ...
A Task Group of the International Commission on Radiological Protection (ICRP) has finished a report Biological Effects after Prenatal Irradiation (Embryo and Fetus) which has been approved by the Main Commission and Will be Published. Some new important scientific data shall be discussed in this contribution. During the preimplantation period lethality of the mammalian embryo is the dominating radiation effect. However, in mouse strains with genetic predispositions it has been shown that also malformations can be caused. This effect is genetically determined and its mechanisms is different from the induction of malformations during major organogenesis. Radiation exposures during this prenatal period leads ato an increase of genomic instability of cells in the normal appearing fetuses. These radiation effects can be transmitted to the next generation. A renewed analysis of individuals with severe mental retardation after exposures during the 8th to 15th week post ...
The development of rechargeable lithium batteries with a high mass capacity, made with non-toxic and low cost materials is an important industrial challenge. Morphological and structural modifications occurring in the electrode materials during charge-output cycles should not lower the electrochemical characteristics and the cycling properties of the battery. Thus the structure of electrode materials must be sufficiently deformable and stable to support the constraints linked with lithium intercalation and de-intercalation (ions and electrons absorption/extraction). The aim of this work is to explain some characteristics (mass capacity, ions and electrons mobility, cycling) using the relation between some mechanisms of lithium insertion (sites occupation, lattice reduction mods) and the nature of atoms and chemical bonds (covalence, ionicity). This approach is developed on 2-D models of crystallized and vitreous sulfur compounds (CdI{sub 2} ...
The Defense Advanced Research Projects Agency (DARPA) inaugurated a program addressing research and development for an Exoskeleton for Human Performance Augmentation in FY!2001. A team consisting of Oak Ridge National Laboratory, the prime contractor, AeroVironment, Inc., the Army Research Laboratory, the University of Minnesota, and the Virginia Polytechnic Institute has recently completed an 18-month Phase I effort in support of this DARPA program. The Phase I effort focused on the development and proof-of-concept demonstrations for key enabling technologies, laying the foundation for subsequently building and demonstrating a prototype exoskeleton. The overall approach was driven by the need to optimize energy efficiency while providing a system that augmented the operator in as transparent manner as possible (non-impeding). These needs led to the evolution of two key distinguishing features of this team's approach. The first is the ...
The mz8310 device support module provides support for the following record types: event, pulseCounter, pulseDelay, and pulseTrain. No driver support is needed. Up to 4 mz8310 modules are supported. Each 8310 module contains 10 channels, which are identified as signals O,...9. Each channel is individually configurable. Each mz83 10 has two Am9513 Timing Controller chips. Each Am9513 has 5 counters.
...six months Organising local tours of the area for up to 1000 affected families in the Izu Penninsula area around Mount Fuji Mobile food stalls that wlll serve up to 10,000 bottles of water and 10,000 servings of food Mobile human waste disposal units Building northern Japan support committees Browser does not support script. Browser does not support script. For further information, please contact: Garry Campbell, PR & ...
A procedure for lowering an offshore rig support block into water, one with water displacement elements, including transfering a structure ready for installation from construction supports onto the grillage that has been set up on the slide, and then lowering the structure together with the grillage into the water. With the goal of dereasing the volume of hydrotechnical operations, the slides have been extended only to the waterline, and the water-displacing elements of the support block are mounted or the structure in a manner whereby the following conditions are fulfilled: Msigmaless than or equal toM /SUB wi/ sigma-W/Lless than or equal toq where Msigma, M /SUB w/ - are the mass moments of the support block and bouyancy forces correspond to the threshhold; sigma and W - the weight force and bouyancy; L - the support length of the block on the grillage; q - the allowable linear ...
Fuel assemblies in a reactor pressure vessel are disposed in a reactor core shroud. The own weight of the fuel assembly is supported by a reactor core support plate, and is supported, for the horizontal direction, by an upper lattice plate and the reactor core support plate. A support portion for the upper portion of the fuel assembly is disposed above the fuel assembly, and a support portion for the support portion described above is joined to a shroud head by welding. The support portion for the upper portion of the fuel assembly has a network-like portion which absorbs and disperses rising force which exerted on the fuel assembly when the fuel assembly is risen by seismic forces. The rising force exerted on the fuel assembly absorbed by the network-like portion is effectively transferred to the shroud head by the ...
Evaluates experiments aimed at selecting optimum design and technical specifications of a support system for junctions of gate roads and longwall faces mined by shearer loaders and powered supports. A set of supports used at a junction of a working face and a gate road consisted of 2 supports (each made up of a roof bar and two hydraulic props). Roof bar length ranged from 4.0 to 5.5 m and from 7.0 to 9.0 m respectively. The support roof bars were parallel to the longitudinal axis of a gate road. Stress distribution in strata surrounding a junction of a working face and a gate road was analyzed. The finite element method was used. Convergence of the roof and the floor of a gate road depending on support yield strength and distance from a measuring point to the supports was analyzed. Recommendations are made for optimum yield strength of the ...
Carbon supported catalysts can lose their activity over a period of time due to the sintering of the nanometer-sized catalyst particles. The sintering of metal clusters on carbon supports can occur due to the weak interaction between the metal and the support and also due to the corrosion of carbon, especially in fuel cell electrocatalysts. The sintering may be reduced by increasing the interaction between the metal and the support and also by increasing the corrosion resistance of carbon supports. In an effort to mitigate the growth of the nanoparticles, carbon-substituted boron defects were introduced in the carbon lattice. The interaction between the Pt nanoparticles on the pure and boron-doped carbon supports was examined using X-ray photoelectron spectroscopy (XPS). The results indicate that the interaction between the Pt nanoparticles and the boron-doped ...
A manipulator for checking the inside of a vertical, flange-shaped collector of a horizontal steam generator consists of a rotating mast with bearings at the top and bottom ends with a support that can be moved along the length of the mast for the checking system mountings. The support is propelled by a drive spindle placed parallel to the mast with its drive head bearing in the support and locked into a toothed rack attached to the mast. The checking system mountings are fitted in or on the walls of the support and are very close to the box-shaped support. Their retractable arms are hinged.
One of the most complicated tasks during the assembly of the Wendelstein W7-X is the installation of the superconductive coil system. The entire magnet system is enclosed between the Outer Vessel and the plasma vessel in high vacuum at 4 K. The coils are supported by a support structure, the Central Support Structure (CSS). The CSS carries all 70 coils, and it is designed as a closed ring made of 5 modules (10 half modules). The whole structure is supported by 10 Cryolegs which rest on the machine base. This paper describes the final design and manufacture of these Cryolegs.
Statement of problem Porcelain fracture associated with an implant-supported, metal ceramic crown or fixed partial denture occurs at a higher rate than in tooth-supported restorations, according to the literature. Implant-specific and patient-specific causes of ceramic failure have not been fully evaluated. Purpose The purpose of this retrospective study was to evaluate the potential statistical predictors for porcelain fracture of implant-supported, metal ceramic restorations. Material and Methods Over a 6-month period, a consecutive series of patients having previously received implant-supported, metal ceramic fixed restorations were examined during periodic recall appointments. The number of supporting implants, number of dental units, type of restoration, date of prosthesis insertion, ...
Objective Over recent years the Internet has become an increasingly popular source of support and information for infertility, with a growing number of online support groups now available to individuals affected by fertility problems. The aims of the present study were therefore to explore the online experiences of individuals accessing infertility support groups via the Internet. Methods Ninety-five participants who were recruited from several online infertility support groups completed an online questionnaire containing a series of open-ended questions. Responses to the open-ended questions were analysed using inductive thematic analysis. Results The thematic analysis revealed five recurrent themes, which were labelled: `unique features of online social support', `improved relationship w...
For purposes of assessing the dumpability of wastes, Article 1 - Ordinance on the Environmentally Responsible Landfilling of Household Wastes (AbfAblV) - of the Ordinance on the Environmentally Responsible Landfilling of Household Wastes and Biological Waste Treatment Plants defines classificaton criteria for biologically and mechanically treated wastes destined for landfilling. The practical experiences that have been gathered with these classification criteria and values were evaluated in a questionnaire-based survey. This was done in particular for the purpose of verifying and validating proposals on the methodology of respiration and fermentation tests. A general finding has been that the application and implementation of the regulations of the AbfAblV is fraught with difficulties. This is evident for one thing in the frequency of analyses and for another in the difficulty of complying with the limit values of the classification criteria. The authors are in ...
Protection of wetlands became a national issue in 1988 when President George Bush pledged no net loss of wetlands in the US under his [open quotes]environmental presidency.[close quotes] As wetlands became a national issue, the job of protecting them became an obligation for many groups, including hydro-power developers. Now, when a site selected for development includes an area that may be classified as a wetland, the developer quickly discovers the importance of recognizing and protecting these natural habitats. Federal legislation severely limits development of wetland, and most states increase the restrictions with their own wetlands regulations. The difficulty of defining wetlands complicates federal and state enforcement. Land that appears to be dry may in fact be classified as a wetland. So, even if a site appears dry, potential hydro developers must confirm whether or not any jurisdictional wetlands are present. Regulated lands include much more than ...
The turbulent history of legislature concerned with the waste-management industry and the amount of material on this subject as well as the significance of the material in its own right led to the decision to publish all legal regulations on waste in one volume. It includes above all the Waste Law, Regulations on Determination of Waste, Regulations on Determination of Residual Products, Technical Instructions for Waste, Regulations for Monitoring Waste and Residual Products, Regulations on Probition from the Use of Chlorofluorohydrocarbons and Halon, Regulations on Packaging and Regulations on Sewage Sludge. The introduction explains the development and the role of the Waste Law and its applicability, goals and principles: The concept of waste, avoidance of waste, avoidance of waste tourism, the general welfare of the public; regulations on waste management, governmental means of monitoring waste management: Obligations to dispose of waste, compulsory ...
The report presents an integrated software system developed at the Norwegian Electric Power Research Institute (EFI), for production scheduling, maintenance handling, network security analysis, inflow forecasting, and load forecasting. The integrated software is being developed with focus on hydro-dominated power supply systems. In specific terms it is expected that application of the software will improve the operational decisions, and make the planning process more effective. The optimal scheduling of hydro resources poses severe computational problems in system operations planning. This necessitates problem decomposition. In the EFI approach, planning is split into three main levels: long-term, mid-term and short-term planning. The long-term planning aims at evaluating the seasonal and pluriannual handling of regional storages in view of firm power supply obligations, inflow statistics, main hydraulic and electric transit limitations, and the available options ...
Most environmental policies provide for special emergency measures to be taken during phases of high pollution, such as smog alarm regulations. These measures serve several purposes and can have various impacts. First of all, they act as a warning to those parts of the population immediately threatened by health hazards (Warnfunktion). They may be directed at short-term pollution reduction via pollution abatement measures proscribed during smog alarm situations (unmittelbare Steuerungsfunktion). In addition, the announcement of emergency measures may signal that pollution levels in general have been too high, indicating that the environmental policies normally pursued do not sufficiently or effectively protect human beings and the environment from harm (Signalfunktion). Emergency measures often contain special regulations obliging industrial polluters to switch to costly, less polluting production processes, or to stop production altogether. This may act as an ...
After more than nine years of negotiations, the US and the Soviet Union signed the Strategic Arms Reduction Treaty (START) in Moscow on July 31, 1991. While the world has changed dramatically since 1982 when the START negotiations began, the treaty remains very much in the US interest. START exacts deep cuts in the most destabilizing and dangerous US and Soviet strategic weapons, and will lead to substantial overall reductions in the strategic nuclear forces of both sides. Moreover, the agreement will create a formal, structured, and predictable strategic environment. It will also impose on the Soviet Union or its successors a legally binding set of obligations that will be in effect for many years, regardless of changes in leadership or form of government. START, with its extensive series of intrusive, cooperative, and technical verification measures, will greatly enhance US knowledge about Soviet strategic nuclear forces and activities. The force reductions, ...
Practitioners who care for pregnant women face dilemmas when their patients use illicit drugs, reject medical recommendations, or cause fetal harm. Many ethics scholars characterize those situations as maternal-fetal conflicts. In conflict-based models, maternal rights are considered to conflict with fetal rights, or moral obligations owed to pregnant women are considered to conflict with those owed to their fetuses. I offer an alternative model of pregnancy ethics by applying relational and equality-based moral theories to situations of fetal harm by pregnant women. In this model, clinicians faced with ethical dilemmas should attempt to understand pregnant women and their decisions within their broad social networks and communities, ask how the clinician's personal standpoint influences outcomes judged to be ethical, and determine whether the clinician's ethical formulations reduce or enhance existing gender, class, or racial inequality. This model focuses on the ...
The Mittelplate oilfield is located in the Waddensea tidelands 8 km off the north sea coast and represents Germany's largest oilfield. Since Mittelplate oil production has started in 1987, RWE Dea AG being the operator in a 50/50 joint venture with Wintershall AG, has continually implemented and improved the sophisticated technology required to exploit natural resources by using safe and environmentally compatible means in the sensitive tideland environment of Mittelplate. Besides the sucessful offshore operations from the man-made Mittelplate Drilling and Production Island, further onshore development has started in 2000 by producing from high-tech ERD wells drilled from onshore locations. The offshore oil production had been transported so far by specially designed tug and tow barges and had been restricted by weather and tide. To overcome this bottleneck and to enable an accelerated offshore drilling and production program a pipeline link between Mittelplate Island and ...
Early in 1988 RWE decided to overhaul the power station at Goldenberg. This was necessary due to the age of the plant, the obligation to supply heat and process steam and recent amendments of environmental legislation. After analysing demands and needs one developed a plant concept with a 290 t/h and a 400 t/h steam generator. Due to lack of space the decision was made in favour of a circulating atmospheric fluidised bed combustion instead of steam generators with pulverised lignite combustion as these steam generators take up much more space due to the legally required desulphurisation plants for gaseous emissions. Apart from generating steam RWE wishes to gain experience with this combustion technology and test it for suitability and use in large-scale plant. (orig./KO) [Deutsch] Aufgrund des fortgeschrittenen Alters, der aktuellen Umweltschutzgesetzgebung sowie bestehender Versorgungsverpflichtungen fuer Waerme und Prozessdampf wurde Anfang 1988 von der RWE ...
Executive summary 1. Few studies have to date explained consumer attitudes and purchase decisions with regard to genetically engineered food products. However, the increased marketing of genetically engineered food products and the considerable concern that consumers seem to express with regard to the technology call for the development of a theoretical basis for research into these issues. 2. The aim of the paper is to present three models which we have developed to explain consumer attitudes, buying behaviour and attitude change with regard to genetically engineered food products. All three models build on established consumer behaviour theory and on existing and comparable research in the field. 3. Consumer attitudes toward genetic engineering in food products are explained in an attitude model that builds on Fishbein's multiattribute attitude model. The model deviates from Fishbein's model in a number of ways: there is an explicit distinction between perceived benefits and risks ...
A novel, obligately anaerobic, extremely thermophilic, cellulolytic bacterium, designated OB47T, was isolated from Obsidian Pool, Yellowstone National Park, WY, USA. The isolate was a non-motile, non-spore forming, Gram-positive rod approximately 2 m long by 0.2 m wide and grew at temperatures between 55-85oC with the optimum at 78oC. The pH range for growth was 6.0-8.0 with values of near 7.0 being optimal. Growth on cellobiose produced the fastest specific growth rates at 0.75 hr-1. The organism also displayed fermentative growth on glucose, maltose, arabinose, fructose, starch, lactose, mannose, sucrose, galactose, xylose, arabinogalactan, Avicel, xylan, filter paper, processed cardboard, pectin, dilute acid-pretreated switchgrass and Populus. OB47T was unable to grow on mannitol, fucose, lignin, Gelrite, acetate, glycerol, ribose, sorbital, carboxymethylcellulose and casein. Yeast extract stimulated growth and thiosulfate, sulfate, nitrate, and sulfur were not ...
CNPT-3 is the laboratory designation of a strain of bacteria that reproduces best at deep-sea pressures. It was isolated from a sample collected at a 5800 m depth of the Pacific Ocean. This isolation was achieved from a sample that had been retrieved without warning. This year we demonstrated that there are similarly behaving bacteria that can be isolated from samples even when retrieved with decompression. The purpose of this project was to define the temperatures and pressures over which CNPT-3 can exist and function. (1) At 2"0C CNPT-3 is eurybathic from about 1000 to 6500 m, as judged from an only slightly pressure dependent generation time. (2) CNPT-3 is unquestionably barophilic at 2"0C, with doubling times of 9 hours at 580 bars and over 18 hours at 1 bar. (3) At 10"0C, reproduction is adversely affected at 1 bar to the extent that CNPT-3 becomes obligately barophilic at 10"0C. Yet reproduction is enhanced above 280 bars and occurs with a regeneration time ...
To many, recent developments in electric markets are perplexing. Competition has appeared, often in the form of new players who do not own and operate generation or transmission facilities. Yet, these players happily enter into contracts obliging them to make or take delivery of power at set prices for months or even years into the future. They seem unconcerned about predicted capacity shortages, fuel price uncertainty or unpredictable plant outages. For the most part, these new players understand these risks quite well. They simply believe in the efficacy of markets. Until recently, price ensured recovery of cost. They foresee a true market where price makes supply equal demand and cost is not a factor in the short term at least. The appearance of such players is an augury of the new industry structure, one in which specialists in taking and managing distinct business risks evolve from within or enter from outside. They take and manage price risk in much the same ...
In neurodegenerative conditions such as Alzheimer's and prion disease it has been shown that host genetic background can have a significant effect on susceptibility. Indeed, human genome-wide association studies (GWAS) have implicated several candidate genes. Understanding such genetic susceptibility is relevant to risks of developing variant CJD (vCJD) in populations exposed to bovine spongiform encephalopathy (BSE) and understanding mechanisms of neurodegeneration. In mice, aspects of prion disease susceptibility can be modelled by examining the incubation period following experimental inoculation. Quantitative trait linkage studies have already identified multiple candidate genes; however, it is also possible to take an individual candidate gene approach. Rarb and Stmn2 were selected as candidates based on the known association with vCJD. Because of the increasing overlap described between prion and Alzheimer's diseases we also chose Clu, Picalm and Cr1, which ...
As a financial institution o the European Union, The European Investment Bank is working and to add substance to the commitments made by the Union and its Member States at Kyoto and subsequently at Johannesburg. Over the last two years, renewable energy sources have attracted funding of more than 1.1 billion from the bank, equivalent to 14% of the total loans granted to the energy sector 7.8 billion), compared to an average o 7.9 % over the previous five years. In order to obviate the detrimental characteristics presented by these investments from a financial viewpoint, in March, 2004 the bank set up a 'CCFF' (Climate Change Financing Facility) of 500 million. Additionally, along with the other financial institutions, the EIB is looking into he possibility of supporting the establishment of European carbon credit trading hubs. Where the economic assessment of these projects is concerned, the bank has decided to take account of external ...
This report documents the technical development for a patent disclosure of a double-clad process for the continuous casting of thin-strip carbon steel. The fundamental idea of the disclosure is to form a product strip by depositing molten steel between two, cooled, clad strips of the same material. The claimed benefits include: (a) the conservation of energy in steel making through the elimination of soaking pits and reheat cycles, and (b) an improved surface on both sides of the as-cast product such that it will be suitable for direct feed to a cold-reduction mill. However, the process as conceived is not necessarily limited to the casting of carbon steel, but may be also applied to other metals and alloys. The work is described under three headings as follows. Preliminary Considerations and Scoping Analysis presents the basic idea of the double-clad, thin-strip casting process; the energy conservation potential; scoping heat transfer calculations for the casting process; and ...
The aim of this work is to develop an industrial process for the synthesis of an extrusible electrolyte polymer for lithium batteries. From literature data and precise specifications the high molar mass EO/OP copolymers synthesis by coordinative catalysis has been studied in order to reach a high productivity and to minimize the treatment steps. Two catalytic systems have been studied: the aluminium alkoxide-based Vandenberg-type catalysis and the calcium alcoholate amides catalysis. The first catalysis performed in solution gives excellent results. Its adaptation to silicon supported catalysis leads to a directly usable polymer in suspension but the productivity falls down and remains to be optimized. The calcium amide catalysis in heptane suspension generates acceptable productivities but also a too high proportion of low molar masses. Various approaches have been studied to minimize this proportion due to the presence of secondary sites that generate a cationic ...
In support of the efforts to apply ceramics in advanced heat engines, a study was made of the sliding performance of ceramics at the ring/cylinder interface of low heat rejection engines. The objective was to understand the basic mechanisms controlling the wear of candidate ceramics and thereby identify means for applying these ceramics effectively. Attempts to operate three different zirconias, silicon carbide, silicon nitride, and several plasma-sprayed ceramic coatings without lubrication were unsuccessful because of high friction and high wear rates. Experiments using a polyalphaolefin lubricant at temperatures to 260 C identified several combinations having wear rates in the general range likely to be acceptable for engines. Plasma-sprayed coatings of chromium oxide and hypersonic powder flame sprayed coatings of cobalt-bonded tungsten carbide performed particularly well as ring coatings. Similar performance was obtained with these ring ...
There are a number of factors favoring synfuel production in South Africa; (1) there are suitable coal fields in the immediate vicinity of our main industrial area.; (2) nature has given us relatively favorable geological conditions permitting highly mechanized extraction techniques so that coal can be delivered to the synfuel plants at Secunda at a cost - including return on capital - of less than $10.00 per ton, based on 1980 price levels; and (3) because the industry and its natural market are remote from the coast, it enjoys some transport protection against products refined from imported crude oil. Even more important we realized a long time ago that in trying to close the gap between the cost of synfuels and international oil prices, one is confronted with a moving target which can more effectively be attacked sooner rather than later. With such highly capital intensive projects, cash operating costs are relatively low. Product price increases once the ...
Since 1975 All Volatile Treatment (AVT) has been the preferred method for controlling the secondary system operating environment in Westinghouse PWR plants. However, since AVT provides no buffering action against corrodent species present in the water as trace contaminants, utilities have initiated programs which combine control of contaminant ingress with total steam generator sludge management. The earliest applications of boric acid, to control denting type corrosion, began in 1978 and have continued up to the present time. Boric Acid has also been added as an inhibitor for SCC/IGA type corrosion since 1985. There are now approximately 30 plants operating with boric acid or boric acid/morpholine chemistry in the secondary system, and a growing number of plants where morpholine is being used as an additive to maintain pH and reduce iron transport attributable to erosion/corrosion. The impact of these modifications in the operating chemistry environment are examined for their ...
This support document summarized the results of botanical surveys conducted as part of a phytoremediation research project that catalogued plants found growing at a petroleum impacted site in Alberta. Phytoremediation refers to the growing of chosen plant species in a polluted site for a period of time in order for the plant to remove contaminants through its natural attributes of absorption, translocation, storage and excretion. Several different plant species with phytoremediation properties are being considered for wide scale bioremediation use. This document described the PhytoPet database which was originally developed as an inventory of plants with phytoremediation capabilities. It was designed to provide easy access to information and help users choose plants with the potential to phytoremediate petroleum hydrocarbons. The information in this document is intended for remediation specialists, site owners and managers as well as environmental scientists in ...
The modification of polymers by radiation grafting has been utilized for several decades. The penetrability of gamma rays allows to modify the internal surfaces of porous materials retaining its mechanical properties. In recent years applications of these materials to obtain chromatographic supports and biocatalysts have been reported. In this work, we described the grafting of glycidyl methacrylate (GMA) onto a macroporous polysulfone polymer. Reproducible amount of grafting, from 10% to 60% was obtained by choosing favourable monomer concentration and gamma radiation doses from 6 kGy up. Afterwards, iminodiacetic acid (IDA) and amino phenyl arsine oxide (PAO) were covalently attached to the grafted polyGMA, in correspondence with the grafting degree. Later on, a recombinant histidin-patch thioredoxin protein (HP-rTrx) was immobilized onto this surface by two different ways, involving specific protein orientations. The first one involves an ...
Full text of publication follows: As the coolant experiences no phase change in the core, SCWRs, unlike LWRs, cannot use design criteria based on the critical heat flux concept. The commonly accepted practice in SCWRs is to specify cladding temperature limits that must be met during transient and accident events. Therefore for the design of the SCWR, it is very important to predict the heat transfer coefficient to the supercritical water coolant with great accuracy. Our recent study focuses on the critical issue of measuring heat transfer to supercritical water at prototypical SCWR conditions and to develop the tools to predict the SCWR thermal behavior. A heat transfer test loop using a surrogate fluids, CO_2, is under construction. The reason of using CO_2 instead of water is that (i) valuable insight of the physical phenomena can be obtained with this fluid, and (ii) some existing facilities already used surrogate fluids, which in general have lower critical pressure and ...
Background. Through PSA screening the rate of prostate cancers detected at an early stage has increased significantly; thus a decrease in mortality can be expected in the near future. Despite all scientific efforts, however, the molecular mechanisms underlying the development and progression of prostate cancer remain poorly understood. Prostate cancer is a disease of aging men and epidemiological evidence supports a major contribution to its development through diet, lifestyle and environmental factors. Genetic instability is the basic phenomenon of tissue cell cancerisation. This instability can be hereditary or due to mutations and other chromosomal aberrations acquired during life. In recent years a large number of interesting data have been collected which show the relationships between focal atrophy and genetic instability of the prostate epithelia. Atrophy can be the result of prostatitis, ischemia as well as of oxidative stress (diet). ...
Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network functions as both ...
A laboratory model of a TPV generator in the kilowatt range was developed and tested. It was based on methane/oxygen combustion and a spectrally matched selective emitter/collector pair (ytterbia emitter-silicon PV cell). The system demonstrated a power output of 2.4 kilowatts at an overall efficiency of 4.5{percent} without recuperation of heat from the exhaust gases. Key aspects of the effort include: (1) process development and fabrication of mechanically strong selective emitter ceramic textile materials; (2) design of a stirred reactor emitter/burner capable of handling up to 175,000 Btu/hr fuel flows; (3) support to the developer of the production silicon concentrator cells capable of withstanding TPV environments; (4) assessing the apparent temperature exponent of selective emitters; and (5) determining that the remaining generator efficiency improvements are readily defined combustion engineering problems that do not necessitate ...
The leading environmental problem facing coastal Louisiana regions is the loss of wetlands. Oil and gas exploration and production activities have contributed to wetland damage through erosion at numerous sites where canals have been cut through the marsh to access drilling sites. An independent oil and gas producer, working with Southeastern Louisiana University and two oil field service companies, developed a process to stabilize drill cuttings so that they could be used as a substrate to grow wetlands vegetation. The U.S. Department of Energy (DOE) funded a project under which the process would be validated through laboratory studies and field demonstrations. The laboratory studies demonstrated that treated drill cuttings support the growth of wetlands vegetation. However, neither the Army Corps of Engineers (COE) nor the U.S. Environmental Protection Agency (EPA) would grant regulatory approval for afield trial of the process. Argonne National Laboratory was ...
The US Department of Energy (DOE) is preparing to perform significant remediation activities of the sites for which it is responsible. To accomplish this, it is preparing a corporate global plan focused on activities over the next decade. Significant in these planned activities is the transportation of the waste arising from the remediation. The costs of this transportation are expected to be large. To support the initial assessment of the plan, a cost estimating model was developed, peer-reviewed against other available packaging and transportation cost data, and applied to a significant number of shipping campaigns of radioactive waste. This cost estimating model, known as the Ten-year Plan Transportation Cost Model (TEPTRAM), can be used to model radioactive material shipments between DOE sites or from DOE sites to non-DOE destinations. The model considers the costs for (a) recovering and processing of the wastes, (b)packaging the wastes for transport, and (c) ...
Geologic sequestration represents a promising strategy for isolating CO{sub 2} waste streams from the atmosphere. Successful implementation of this approach hinges on our ability to predict the relative effectiveness of subsurface CO{sub 2} migration and sequestration as a function of key target-formation and cap-rock properties, which will enable us to identify optimal sites and evaluate their long-term isolation performance. Quantifying this functional relationship requires a modeling capability that explicitly couples multiphase flow and kinetically controlled geochemical processes. We have developed a unique computational package that meets these criteria, and used it to model CO{sub 2} injection at Statoil's North-Sea Sleipner facility, the world's first saline-aquifer storage site. The package integrates a state-of-the-art reactive transport simulator (NUFT) with supporting geochemical software and databases (SUPCRT92). In our Sleipner ...
The Nuclear Renaissance is stumbling at the very same time it should speed up in order to help control the climate change and meet a fast growing energy need in a large part of the world. Rising costs of projects, uncertainties about their completion, rocketing safety requirements, and financial constraints are key factors which slow down the Nuclear Renaissance. Furthermore, the legal infrastructure required from any country to enter a commercial nuclear programme (safety authorities, fuel cycle, and waste disposal) is a major hurdle s which impedes consideration for small to mid size reactors, well suited for many countries. The paper prepared and presented by Alain Bugat (Chairman of NucAdvisor and former Head of the French Atomic Energy Commission), Dominique Vignon (CEO of NucAdvisor and former President and CEO of AREVA NP) and Michel Lecomte (Co-founder NucAdvisor) reviews the present status of the Nuclear Renaissance. Based on an analysis of initial versus actual plans for all ...
The hypothesis that accumulation against sizable chemical gradients of free (non-phosphorylated) 2-deoxy-D-glucose (2dGlc) in isolated rat adipocytes results from an intracellular compartmentation of free hexose was investigated. Cells exposed to 20 ..mu..g/ml digitonin for 10' demonstrated an increased plasma membrane permeability indexed by increased L-glucose entry rates and cellular (presumably cytosolic) protein and K/sup +/ loss. Functional integrity of intracellular organelles was indicated by the ability of the cells to support ATP-driven /sup 45/Ca/sup 2 +/-uptake. Equilibrium 3-O-methylglucose (3-O-MG, a non-accumulated hexose) levels were unaffected. These data suggest a specific permeabilizing action of digitonin at the plasma membrane having no effect on intracellular organelles or passively distributed solutes. Upon addition of digitonin, free 2dGlc fell from 66.5 +/- 8.9 to 7.4 +/- 2.3 pmol/10/sup 5/ cells, a value not significantly ...
One of the Eddy Current Testing issues in aeronautics is the inspection of fastened structures to detect flaws nearby rivets which can grow because of mechanical stress. EADS and the CEA LIST have started a collaborative work with the support of the Ile-de-France Region to develop a simulation tool of EC fastened structures testing, integrated to the CIVA platform, aimed at conceiving testing methods, optimizing and qualifying it. The volume integral method using the Green dyadics formalism has been chosen in order to get a fast resolution of Maxwell equations. A first milestone was to build a simulation model of multilayer structures testing, thanks to the use of the multilayer Green dyads. Because of the rivet volume, 60 times bigger than the one of a typical flaw, a large number of discretization cells are needed. Therefore an iterative method has been developed in order to numerically solve large calculation zones. Finally, the flaw ...
Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanicalsupported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the MgO(MG-S) with Copper and Fe-Ni Alloy relaxation ...
The reconstruction of segmental defect in long bone is a clinical challenge. Multiple surgeries are typically required to restore the structure and function of the affected defect site. In order to overcome this defect a biodegradable bone tissue engineering scaffold is used. This scaffold acts as a carrier of proteins and growth factors, while also supporting the load that the bone would normally sustain, until the natural bone can regenerate in its place. Work was done to optimize an existing solid free-form scaffold design. The goal of the optimization was to increase the porosity of the scaffold while maintaining the strength of a previously-tested prototype design. With this in mind, eight new designs were created. These designs were drawn using CAD software and then through the use of finite element analysis the theoretical ultimate compressive strength of each design was obtained. Each scaffold design was constructed by casting a thermal-curable ...
During the years 1995-1999, an international effort was going on under the title DECOVALEX II, in order to study the coupled thermo-hydro-mechanical (THM) effects in the water containing fractured rock mass caused by the heat generation of spent fuel canisters in a repository. The project was a continuation project of DECOVALEX (1991-1996). The name comes from the acronym 'an international co-operative project for the DEvelopment of COupled models and their VALidation against EXperiments in nuclear waste isolation'. Radiation and Nuclear Safety Authority (STUK) was one of the eleven Funding Organizations in the international project. STUK's Research Team was the Technical Research Centre of Finland, VTT Communities and Infrastructure. To support and coordinate the national research work, STUK formed a National DECOVALEX II Group (NDG). The group had representatives from six research organisations and rock engineering ...
GaAs-based dc high voltage photoguns used at accelerators with extensive user programs must exhibit long photocathode operating lifetime. Achieving this goal represents a significant challenge for proposed high average current facilities that must operate at tens of milliamperes or more. This paper describes techniques to maintain good vacuum while delivering beam, and techniques that minimize the ill effects of ion bombardment, the dominant mechanism that reduces photocathode yield of a GaAs-based dc high voltage photogun. Experimental results presented here demonstrate enhanced lifetime at high beam currents by: (a) operating with the drive laser beam positioned away from the electrostatic center of the photocathode, (b) limiting the photocathode active area to eliminate photoemission from regions of the photocathode that do not support efficient beam delivery, (c) using a large drive laser beam to distribute ion damage over a larger area, ...
AREVA is the world leader in the design and construction of nuclear power plants, the manufacture of heavy components, and the supply of nuclear fuel and nuclear services such as maintenance and inspection. The Equipment Division provides the widest range of nuclear components and equipment, manufactured at its two facilities in Jeumont, northern France, and St. Marcel, in Burgundy. The St. Marcel plant, set on 35 ha (87.5 acres) near Chalon-sur-Saone, was established in 1973 in a region with a long history of specialized metalworking and mechanical activities to meet the demand for non-military nuclear requirements in France. The site offers two advantages: - excellent facilities for loading and transporting heavy components on the Saone river, - it's proximity to other group sites. Since its completion in 1975, the Chalon/St. Marcel facility has manufactured all the heavy components for French pressurized water reactors (PWRs) ranging from 900 MW to 1500 ...
Full text: The transmutation of nuclear waste to reduce the burden on a geological repository is a relevant topic within the Program of Nuclear Safety Research of the Research Centre Karlsruhe. Several studies have confirmed that a high efficiency of transmutation of actinides is reached in fast neutron spectrum reactor system. Therefore, an important effort is dedicated to the study of transmutation strategies with different fast reactors and their associated technologies. Moreover, in international contexts as Generation IV International Forum (GIF) and Sustainable Nuclear Energy Technology Platform (SNETP), fast reactors are considered in the frame of sustainable development of nuclear energy and reduction of waste. The systems that are currently under investigation, in the frame of the different fuel cycle scenarios, are liquid metal cooled and gas cooled fast reactors as well as Accelerator Driven Sub-critical Transmutation devices (ADS). These innovative reactor systems, call for ...
For the first time in scientific literature, in our joint work with Dr. G. Ladwig in 1978 it was established phase portraite of the oxide vanadium-phosphorus system within wide range of P/V ratios from 0.5 to 3.2. Some later those data were confirmed. By investigation of the properties of individual vanadium-phosphorus phases it was also shown that the active component of such catalysts in n-butane oxidation was vanadyl pyrophosphate phase (VO){sub 2}Pr{sub 2}O{sub 7}. From then the conclusion has been evidenced by numerous publications and at present it has been out of doubt practically all over the world. It was hypothized that the unique properties of (VO){sub 2}P{sub 2}O{sub 7} in the reaction of n-butane oxidation could be explained by the presence of paired vanadyl groups and nearness of the distances between neighbouring vanadyl pairs and that between the first and fourth carbon atoms in n-butane molecule. The molecule activation occured at the latter atoms by proton ...
A post-irradiation annealing study was conducted with use of reactor pressure vessel(RPV) steel A533B C1.1 base metal irradiated to a dose of 4.84x10"1"8 n/cm"2 at about 380 deg C. Microhardness and positron annihilation (PA) methods were used to obtain better understanding of the recovery of radiation hardening. Isochronal anneal experiments indicated that two recovery processes occur during annealing of irradiated specimens. The first recovery process occurs in the temperature of 280-305 deg C. The variations of Ip, Iw and R parameters indicated that the formation of vacancy clusters by vacancy aggromeration and the annihilation parameters measured indicated that the dissolution of carbon atoms decorated around vacancy-type defects and possible precipitates, and the annihilation of monovacancies give rise to the second recovery process. It was further indicated that radiation anneal hardening (RAH) in the range of 305-405 deg C between the temperature ranges for the two processes ...
Patient decision support systems have a promising role in the delivery of health care. However, the best approach for further development of these systems is a matter of speculation. To help chart a...Full Text Available
The original plan for support of research in geothermal reservoir engineering, GREMP, is reviewed and compared with accomplishments to date. A commentary on the comparison and an updated plan are presented. Also included are a justification of the updated plan and a revised management plan. (MHR)
Main results of 15-year SSTC NRS activity in the field of technical support of regulatory authority are presented. The article also described management policy, quality assurance system, personnel training system and international co-operation of SSTC. (author)
BackgroundSupport groups have proved to be effective in reducing the burden on family caregivers of dementia patients. Nevertheless, little is known about the factors that influence...Full Text Available
A knowledge-based expert system has been developed to support human decision makers who assess drug products for inclusion in the Saskatchewan Formulary. Formulary inclusion and deletion decisions...Full Text Available
This paper evaluates the Post-Hospital Support Program for the frail elderly and their caregivers using a quasi-experimental design. The program goals were to reduce stress in the caregivers, improve...Full Text Available
It has been discovered that iron(III) chloride complexes supported on activated charcoal oxidize phosphine under normal conditions. The process accelerates as the concentration of the chloride ions and the proton acid increases.
ObjectiveMany hospitals utilize antimicrobial management teams (AMTs) to improve patient care. However, most function with minimal computer support. We evaluated the effectiveness...Full Text Available
PURPOSE We wanted to assess the impact of an electronic health record–based diabetes clinical decision support system on control of hemoglobin A1c (glycated hemoglobin),...Full Text Available
Objective To compile and evaluate the evidence on the effects on health and social outcomes of computer based peer to peer communities and electronic self support groups, used by people...Full Text Available
DOE is supporting the development of several conversion processes that are currently in the pilot plant stage. Each of these processes is described briefly and information given as to contractor, contract, funding, site and current progress. Several support projects are treated similarly. (LTN)
Social support is a critical, yet underutilized resource when undergoing cancer care. Underutilization occurs in two conditions: (a) when patients fail to seek out information, material assistance,...Full Text Available
Incorporation of clinical decision support (CDS) capabilities is required to realize the greatest benefits from computerized provider order entry (CPOE) systems. Discussions at a conference on CDS in...Full Text Available
As an engineered barrier system in the geological disposal of high-level waste, multibarrier system is considered. Multibarrier system consists of the vitrified waste, the overpack and the buffer. Bentonite is one of the potential material as the buffer because of its low water permeability, self-sealing properties, radionuclides adsorption and retardation properties, thermal conductivity, chemical buffering properties, overpack supporting properties, stress buffering properties, etc. As the construction technology of the buffer, the block installation method and in-situ compaction method, etc, are being investigated. The block installation method is to emplace the buffer blocks manufactured in advance at the ground facility, and construction processes of the block installation method at the underground will be simplified compared with the in-situ compaction method. However, the block joints of buffer might be a mechanical weak portion or might ...
... due to the evolving nature of the Strategy Maps and the changing priority roles, it was decided not to link the SMSP directly with any Strategic Plans. ...
... with the additional US funds supporting Islamic ... the FATA and NWFP, keeping Pakistan's government and ... Without these madrassas, the TTP is left ...
... DARPA UUV and the UUV support simulator. ... Modular connections for robot arm manipulators ... Intelligent mobile robots will be performing many ...
The title invention aims at a vibrations-free running of the flywheel to realize a high speed (18,000-20,000 revolutions per minute). The flywheel consists of a case which holds a central stator, a rotor and two ball-bearings. The ball-bearings have a first radial stiffness and are placed in between the rotor and an upper, respectively lower support bearer. The support bearers are supported on the stator with a second radial stiffness. The top and the bottom of the stator is connected to the case by means of a support with a third stiffness. 6 figs.
sabot: A device fitted around or in back of a projectile in a gun barrel or launching tube to support or protect the projectile or to prevent the escape of ...
with the support and cooperation of the American Meteorological Society, the Marine Technology Society, the National Aeronautics and Space Administration, the National Institute...
The sunlight-induced photocatalytic oxidation of aqueous benzene on TiO(2)-supported gold nanoparticles was considerably improved when the reaction was conducted under a CO(2) atmosphere. 13% yield and 89% selectivity of phenol was obtained on P25-supported gold nanoparticles under 230 kPa of CO(2). PMID:21952312
ABSTRACT Extending the unified theory of acceptance and use of technology (UTAUT) model, this study postulates a model of online social support. The model is empirically tested using data from undergraduates in Taiwan regarding their usage of instant messaging (IM). The test results indicate that all model paths are significant, except that the path between online social support and facilitating conditions is insignificant. This study offers limitations and implications.
Information technology plays an important role in medicine because of the advanced decision support systems (DSS) it can provide. We provide an overview of the building blocks necessary for a medical decision support system and introduce seven research articles in this special issue that describe the development and evaluation of individual medical DSS building blocks or complete medical DSS.
The Coordinated Research Project is a topical collection of research agreements and contracts. The research contracts are awarded with financial support of about 10-20% of the total contract cost. Among the activities of the project is the organization of consultant group meetings and workshops involving several international experts and representatives of users and developers of border radiation monitoring equipment. The project also supports in coordinating the development of equipment and techniques for up-to-date border monitoring and in establishing of a process for providing nuclear forensics support to member states
A zinc-air battery in a case including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit.
A zinc-air battery in a case is described including a zinc particle bed supported adjacent the current feeder and diaphragm on a porous support plate which holds the particles but passes electrolyte solution. Electrolyte is recycled through a conduit between the support plate and top of the bed by convective forces created by a density of differential caused by a higher concentration of high density discharge products in the interstices of the bed than in the electrolyte recycle conduit. 7 figures.
Genetic effects on mechanical properties have been demonstrated in rodents, but not confirmed in primates. Our aim was to quantify the proportion of variation in vertebral trabecular bone mechanical...Full Text Available
The mechanical properties of laminated window profiles manufactured using two types of adhesives were determined. The objective of this study is to evaluate the effects of heat treatment on some mechanical...Full Text Available
Abstract People with a physical disability are a population who for a number of reasons may be vulnerable to social isolation. Research into Internet based support sites has found that social support and an online sense of community can be developed through computer mediated communication channels. This study aims to gain an understanding of the benefits that membership of disability specific online communities may have for people with a physical disability. An online survey was administered to a sample of users of such sites (N = 160). Results indicated that users did receive moral support and personal advice through participating in such online communities. Further, results indicated that online social support and feeling a sense of community online were positively associated with partic...
Background: The Internet has become a popular source of health information for patients with a variety of medical concerns; however, research examining patient interactions on the Internet has been limited. Purpose: Four questions were examined in a survey study of hysterectomy patients who visited http://www.hystersisters.com: (a) Do hysterectomy patients use the support Web site because they perceive their proximal sources of social support to be inadequate? (b) What kinds of support do patients receive from the Web site? (c) What attributes characterize the "Hystersisters" that are perceived to be most helpful? (d) How do informational sources vary depending on the nature of the patient concern? Methods: Women (N = 137) responded to questions about social support, Web site use, and perc...
Industrial solid wastes (fly ash and red mud, a by-product of the aluminium industry) have been employed as supports for preparation of Ru-based catalysts. Physical and chemical treatments on red mud were conducted and these modified supports were also used for preparation of Ru-based catalysts. Those Ru catalysts were characterized by various techniques such as N2 adsorption, H{sub 2} adsorption, XRD, XPS, and temperature-programmed reduction (TPR), and were then tested for catalytic ammonia decomposition to hydrogen. It was found that red-mud-supported Ru catalyst exhibits higher ammonia conversion and hydrogen production than fly-ash-supported catalyst. Heat and chemical treatments of the red mud greatly improve the catalytic activity. Moreover, a combination of acid and heat treatments produces the highest catalytic conversion of ammonia. 35 refs., 4 figs., 4 tabs.
This study validates a research model that examines usage of instant messaging (IM) from the aspect of online social support. Drawing on the social capital theory, this study postulates that IM usage is indirectly affected by social support via the mediation of the following six dimensions of social capital: commitment, reciprocity, shared codes and language, shared narratives, centrality, and network ties. The model tests data obtained from business organizations in Taiwan, and the results suggest that the indirect influence of social support on IM usage through shared codes and language is significant, and the indirect influence of social support on IM usage through centrality is also significant. Managerial implications and limitations of the empirical findings are provided.
Y-zeolite supported catalysts were applied to the hydrocracking of coal-derived liquids. By the introduction of two-stage upgrading consisting of hydrotreating and hydrocracking, Wandoan coal-derived middle distillate was hydrocracked over Ni-Mo/Y-zeolite, producing a high gasoline fraction yield. Zeolite supported catalysts gave little hydrocracked compounds in the hydroprocessing of coal-derived heavy oils, even after hydrotreatment. The reaction inhibitors which seriously poison the active sites of zeolites were found to be small nitrogen-containing molecules. In the hydroprocessing of coal-derived heavy oils, zeolite supported catalysts were inferior to alumina supported catalysts. This is due to the high hydrocracking but low hydrogenation activity of zeolite supported catalysts. 22 refs., 5 figs., 11 tabs.
SUMMARYHomeostatic synaptic plasticity is a negative feedback mechanism neurons use to offset excessive excitation or inhibition by adjusting their synaptic strengths. Recent...Full Text Available
BackgroundAlternative splicing is an important mechanism mediating the diversified functions of genes in multicellular organisms, and such event occurs in around 40-60% of human...Full Text Available
The mechanism of hyaluronan biosynthesis in vertebrates had been proposed to occur at the reducing end of growing chains. This mechanism was questioned because a recombinant synthase appeared to add...Full Text Available
Full text: The IRSN has been organizing enquiries with the French population about risk and risk perception for a long time. In 2002, a collaboration between the IRSN in France and the SCK.CEN in Belgium has been set-up to simultaneously (November 2002) organise this poll in both countries. In each country, a representative sample of the population (over 1000 participants per country) has been consulted by Computer Aided Personal Interviews of about 30 minutes with the professional help of commercial companies: BVA in France and Research International in Belgium. The enquiry yields a broad spectrum of interesting data; here only the results relevant for the emergency context will be presented. One should be aware that these data were collected in a 'normal' period; important differences in behaviour may occur given a serious crisis. A first finding is that more than half of the respondents are convinced that an accident as severe as the Chernobyl disaster may happen in their country as ...
Seven years ago 164 governments, together with partner organizations from around the world, made a collective commitment to dramatically expand educational opportunities for children, youth, and adults by 2015. Participants at the World Education Forum in Dakar, Senegal, endorsed a comprehensive vision of education, anchored in human rights, affirming the importance of learning at all ages and emphasizing the need for special measures to reach the poorest, most vulnerable and most disadvantaged groups in society. This sixth edition of the "Education for All (EFA) Global Monitoring Report" assesses the extent to which these commitments are being met. There is clearly a "Dakar effect," evidence that rallying around common goals can mobilize countries to empower individual lives. Partly because of the abolition of tuition fees, more children are enrolled in school than in 2000, with the sharpest increases in the regions farthest from the goals set in Dakar. Many governments have ...
Our work has focused on the development and analysis of domain decomposition algorithms for a variety of problems arising in continuum mechanics modeling. In particular, we have extended and analyzed FETI-DP and BDDC algorithms; these iterative solvers were first introduced and studied by Charbel Farhat and his collaborators, see [11, 45, 12], and by Clark Dohrmann of SANDIA, Albuquerque, see [43, 2, 1], respectively. These two closely related families of methods are of particular interest since they are used more extensively than other iterative substructuring methods to solve very large and difficult problems. Thus, the FETI algorithms are part of the SALINAS system developed by the SANDIA National Laboratories for very large scale computations, and as already noted, BDDC was first developed by a SANDIA scientist, Dr. Clark Dohrmann. The FETI algorithms are also making inroads in commercial engineering software systems. We also note that the analysis of these ...
Ageing of nuclear power plants means evolution of material or equipment properties on one side, and evolution of personnel skill and procedure adequacy on the other side, both of which, after a certain time, may not be compatible with the required safety provisions, or with an economic operation of the plant. Repair or replacement of components, as well as change in service conditions for a better compatibility with component reduced capabilities can be used to mitigate ageing effects. The paper summarises the results of a study conducted in this field with the support of the European Commission. It presents: the synthesis of the work done under international auspices, and in the European context; the comparison of ageing management approaches used in several European countries with international recommendations; the summary of the various potential phenomena and their governing parameters, the methods of in-service ageing identification and possible mitigation ...
The absence of high-temperature electronics is an obstacle to the development of untapped energy resources (deep oil, gas and geothermal). US natural gas consumption is projected to grow from 22 trillion cubic feet per year (tcf) in 1999 to 34 tcf in 2020. Cumulatively this is 607 tcf of consumption by 2020, while recoverable reserves using current technology are 177 tcf. A significant portion of this shortfall may be met by tapping deep gas reservoirs. Tapping these reservoirs represents a significant technical challenge. At these depths, temperatures and pressures are very high and may require penetrating very hard rock. Logistics of supporting 6.1 km (20,000 ft) drill strings and the drilling processes are complex and expensive. At these depths up to 50% of the total drilling cost may be in the last 10% of the well depth. Thus, as wells go deeper it is increasingly important that drillers are able to monitor conditions down-hole such as temperature, pressure, ...
The integrity of the RPV head and reactor internals was assessed by means of fluid-structural analyses using a coupled method to evaluate the water hammer phenomenon arising from high burnup fuel failure under RIA conditions. The fluid viscosity effect on the water column burst as well as the complex three-dimensional flow paths caused by a core shroud and standpipes were considered in this study. The three analysis scenarios were designed to investigate the above mentioned influential factors separately. In the first scenario, a two-dimensional axisymmetric reactor vessel model without any reactor internals was modeled to assess the influence of the fluid dynamics in the NSC RIA regulatory evaluation. This model has an actual RPV geometry and can be simply separated from other influential factors in order to concentrate only on investigation of the fluid viscosity effect. In the second scenario, a two-dimensional axisymmetric reactor vessel model with major reactor internals, such as ...
This report describes work accomplished in the project, titled ''Development of Appropriate Resistance Spot Welding Practice for Transformation-Hardened Steels.'' The Phase 1 of the program involved development of in-situ temper diagrams for two gauges of representative dual-phase and martensitic grades of steels. The results showed that tempering is an effective way of reducing hold-time sensitivity (HTS) in hardenable high-strength sheet steels. In Phase 2, post-weld cooling rate techniques, incorporating tempering, were evaluated to reduce HTS for the same four steels. Three alternative methods, viz., post-heating, downsloping, and spike tempering, for HTS reduction were investigated. Downsloping was selected for detailed additional study, as it appeared to be the most promising of the cooling rate control methods. The downsloping maps for each of the candidate steels were used to locate the conditions necessary for the peak response. Three ...
Thioredoxin reductase, lipoamide dehydrogenase, and glutathione reductase are members of the pyridine nucleotide–disulfide oxidoreductase family of dimeric flavoenzymes. The mechanisms and structures...Full Text Available
In this study, a novel compliant mechanism, ''partially compliant spatial slider-crank (RSSP)'' is proposed. All possible configurations of compliant RSSP mechanisms are classified and discussed. A method is derived to determine deflection of the multiple-axis flexural hinge for all positions of the crank. A design procedure for partially compliant RSSP mechanisms is introduced. In order to prove the feasibility of the proposed mathematical model, a real model is built and it is shown that results are consistent.
A system for partial mechanisation of the support work with roadway driving machines consisting of a crawler undercarriage carrying a selective cutter with a cutting jib on a rotary tower is claimed. The system comprises a support manipulator movable in longitudinal direction over the rotary tower and cutting jib and a preassembly table with a number of brackets to take up and preassemble a support structure consisting of profile segments, preferably an arc-shaped support with a cap made up for several parts. The system is characterized in that the preassembly table is mounted on one side of the selective cutter and has one straight vertical guide bar each for at least two cap brackets which can be continuously adjusted in height, and in that the manipulator mounted on the selective cutter has a horizontally suivelling head which may grip under the cap of the preassembled structure on the preassembly ...
Role-limiting approaches support knowledge acquisition (KA) by centering knowledge base construction on common types of tasks or domain-independent problem-solving strategies. Within a particular problem-solving strategy, domain-dependent knowledge plays specific roles. A KA tool then helps a user to fill these roles. Although role-limiting approaches are useful for guiding KA, they are limited because they only support users in filling knowledge roles that have been built in by the designers of the KA system. EXPECT takes a different approach to KA by representing problem-solving knowledge explicitly, and deriving from the current knowledge base the knowledge gaps that must be resolved by the user during KA. This paper contrasts role-limiting approaches and EXPECT`s approach, using the propose-and-revise strategy as an example. EXPECT not only supports users in filling knowledge roles, but also provides ...
A 4-loop Pressurised Water Reactor (PWR) primary coolant system has been analysed for the postulated Loss of Coolant Accident (LOCA) event in order to derive peak dynamic loads for qualifying the design of equipment supports and pipe whip restraints. Pipe whip restraints as well as pipe and equipment supports are nonlinear by nature because of the presence of gaps and the different directional stiffnesses arising from snubber, steelwork and geometric and material interaction at the concrete to steel embedment. The different structural idealisations for the supports and restraints have an influence on the dynamic response of the structure. In the first of the two part paper a range of idealisation models for the Steam Generator and Reactor Coolant Pump vertical columns ranging from elastic stiffnesses to bilinear stiffnesses with or without preload were examined. Due to both structural and loading complexity, the behaviour ...
The U.S. Support Program to International Atomic Energy Agency (IAEA) Safeguards (USSP) was established in 1977 to transfer US technology and expertise to assist the IAEA Department of Safeguards because its limited budget and scope would not allow for R&D activities and the procurement of specialized or customized equipment. Over the years, the USSP and the Department of Safeguards have worked together continuously to develop and improve processes for requesting, selecting, and managing projects that support the Safeguards verification mission. This paper will discuss the main USSP processes for accepting and processing Safeguards requests, and managing and reporting task progress.
Reinforced (heterogel) silicate materials containing an amorphous and a crystalline phase are being used more and more industry. Such systems are energetically unsaturated and therefore promising for use in catalysts. The authors used two reinforced materials as supports: an aluminosilicate containing a zeolite (the cracking catalyst, tseokar) and asbestos-containing aluminosilicate. The active component was introduced by impregnation, and this was followed by heat treatment during which the chemical composition and porous structure were formed. The impregnating mixture consisted of solutions of potassium sulfate and vanadate of the required concentrations. The testing shows that reinforced heterogel systems are promising as support materials for sulfuric acid catalysts.
National Nuclear Safety Department is authorized by Infra (Iranian Nuclear Regulatory Authority) for issuing rules and regulation and conducting the licensing and supervisory process for nuclear facilities. The main responsibilities of the NNSD are conducted via five main division are, nuclear codes and standards, Nuclear Safety assessment, Authorization, Inspection and Enforcement and Technical Support. In this paper, the functions and responsibilities of TSD in enhancing nuclear safety are described. Examples of main tasks to support the Nuclear Safety assessment division regarding to technical calculations and research of safety issues in licensing documents are provided. (author)
The risk analysis was carried out in consideration of conditions prevailing at the Kalkar site analogous to the investigations in phase A of DRS (German Reactor Study). Earthquake design loads include the probabilities of upper deviations of the site intensities to be expected. The calculations of dynamic loads for select buildings are made using models and computational methods. Component analyses were performed analogous to DRS for the supports of large components, supports of the roof construction of the reactor building taking into account support reserves due to plastic work capacity, wall disks in steam generator buildings and switchboard plant buildings. (DG).
This paper describes examples of the damage resulting from the impact of a whipping pipe on a nearby pressurised pipe. The work is a by-product of a study of the motion of a whipping pipe. The tests were conducted with small-diameter pipes mounted in rigid supports and hence the results are not directly applicable to large-scale plant applications where flexible support mountings are employed. The results illustrate the influence of whipping pipe energy, impact position and support type on the damage sustained by the target pipe.
This paper describes examples of the damage resulting from the impact of a whipping pipe on a nearby pressurised pipe. The work is a by-product of a study of the motion of a whipping pipe. The tests were conducted with small-diameter pipes mounted in rigid supports and hence the results are not directly applicable to large-scale plant applications where flexible support mountings are employed. The results illustrate the influence of whipping pipe energy, impact position and support type on the damage sustained by the target pipe. (author).
The profitability of combustion turbines intended for export is of extreme importance for Electricite de France. It is principally during the development phase of a project that one can ensure resect of two indissociable factors, essential to the per-kWh production cost: global operating costs and performance in terms of reliability and availability. The approach proposed here advocates the global acquisition of the installation and its logistic support. Generally applicable recommendations are given. They enable integrating in the future plant specifications all requirements relative to plant reliability, availability, maintainability and logistic support. They are structured according to type: expression of needs and management factors. (orig.) 4 refs.
As the new entrants in the global nuclear construction market are increasing and the establishment of an effective and sustainable regulatory infrastructure becomes more important, they have requested international assistance from the international nuclear communities with mature nuclear regulatory programmes. It needs to optimize the use of limited resources from regulatory organization providing support to regulatory infrastructure of new comers. This paper suggests the resource portfolio concept like a GE/Mckinsey Matrix used in business management and tries to apply it to the current needs considered in the regulatory support program in Korea as the case study
Earlier studies had concluded that the preferred direction of the rocket nozzle should ..... Center had to redesign the sensor canisters, brackets and cable supports. ... depending on inspection of the quality of the incoming pictures in real-time. ...
The present paper is a comparative study of the cerium-containing nickel catalysts supported on x- and y-zeolites. In general, the addition of cerium ions caused an increase in the catalytic activity for CO hydrogenation and shifted the product selectivity to high molecular weight hydrocarbons. The degree of the effect of cerium additive depends on the ratio of cerium to nickel contents, the reduction temperature, and the nature of the supporting materials. Catalyst characterization, including volumetric hydrogen chemisorption, temperature programmed reduction/desorption, x-ray diffraction, surface area measurements, in-situ infrared spectroscopy and x-ray photoelectron spectroscopy, was performed in order to interpret the phenomena due to the effects of cerium additives and the support effect on Ni/zeolite catalysts.
... 7th Joint Task Force Augmentation Team Schwetzingen ... Headquarters 85th Division Training Support, Detach 2 ... 20th Special Forces Company A ...
... Astronomy & Space Biology Chemistry & Materials Computing Earth & Environment Education ... Materials Research Center at the University of Chicago, one of nearly 30 NSF-supported Materials ...
Oct 2, 2007 ... Other payloads included the Orbiter Experiments Autonomous Supporting Instrumentation System-1 (OASIS-1), a cooling system designed for ...
The Computation Directorate at Lawrence Livermore National Laboratory has four major areas of work: (1) Programmatic Support -- Programs are areas which receive funding to develop solutions to problems or advance basic science in their areas (Stockpile Stewardship, Homeland Security, the Human Genome project). Computer scientists are 'matrixed' to these programs to provide computer science support. (2) Livermore Computer Center (LCC) -- Development, support and advanced planning for the large, massively parallel computers, networks and storage facilities used throughout the laboratory. (3) Research -- Computer scientists research advanced solutions for programmatic work and for external contracts and research new HPC hardware solutions. (4) Infrastructure -- Support for thousands of desktop computers and numerous LANs, labwide unclassified networks, computer security, computer-use ...
... the political charisma to compete with support of heavy divisions until recently. ... 82nd Airborne Division, the 101st Air Assault Division, the ...
... Division and the 82nd ABN Division spearheaded a ... attack through the stalled 90th Division to ... mi,_es, which included airborne infantrv, regular ...
Modern HENP experiments such as CMS and Atlas involve as many as 2000 collaborators around the world. Collaborations this large will be unable to meet often enough to support working closely together. Many of the tools currently available for collaboration focus on heavy-weight applications such as videoconferencing tools. While these are important, there is a more basic need for tools that support connecting physicists to work together on an ad hoc or continuous basis. Tools that support the day-to-day connectivity and underlying needs of a group of collaborators are important for providing light-weight, non-intrusive, and flexible ways to work collaboratively. Some example tools include messaging, file-sharing, and shared plot viewers. An important component of the environment is a scalable underlying communication framework. In this paper we will describe our current progress on building a dynamic and ad hoc ...
The long-term support required from Canada in the operation and maintenance of overseas CANDU nuclear generating stations after commercial operation has commenced is described, with reference entirely to the KANUPP reactor. This includes: technical support to station staff to increase plant reliability and maintainability; assistance with plant improvements; procurement of spares and consumables; and assistance with training programmes. This technical support may be provided by a small number of Canadian staff actually resident at the power station; by short-term visits of Canadian specialists to site and by technical and procurement services provided from Canada. Examples of technical problems experienced are given, showing typical services required from Canada.
... rate on the tensile properties of SA-106 carbon steel pipe, in support of analysis and experimental modeling of postulated pipe whip in nuclear ...
Collectively, the organizations participating in the Site Operator Program have over forty years of EV experience and have operated electric vehicles (EVs) for over 600,000 miles, providing the most extensive EV operating and knowledge base in the country. The Site Operator Program is intended to provide financial and technical support and organizational resources to organizations active in the advancement of electric vehicles. Support is provided for the demonstration of vehicles and the test and evaluation of vehicles, components, and batteries. Support is also provided for the management and support of the program for the participating organizations. The Program provides a forum for participants to exchange information among the group, as well as with vehicle and equipment manufacturers and suppliers, and the public. A central data base at the Idaho National Engineering Laboratory provides a ...
Collectively, the organizations participating in the Site Operator Program have over forty years of EV experience and have operated electric vehicles (EVs) for over 600,000 miles, providing the most extensive EV operating and knowledge base in the country. The Site Operator Program is intended to provide financial and technical support and organizational resources to organizations active in the advancement of electric vehicles. Support is provided for the demonstration of vehicles and the test and evaluation of vehicles, components, and batteries. Support is also provided for the management and support of the program for the participating organizations. The Program provides a forum for participants to exchange information among the group, as well as with vehicle and equipment manufacturers and suppliers, and the public. A central data base at the Idaho National Engineering Laboratory provides a ...
The paper deals with the reliability-based design optimization (RBDO) of a riser support installed on a floating production storage and offloading (FPSO) unit under operation, extreme, damaged, and one line failure cases and installation loading conditions. The optimization problem is formulated such that probabilistic thickness variables described with random characteristics are determined by minimizing the weight of the riser support structure subjected to stress constraints for the given target reliability. The initial design model is generated based on actual FPSO riser support specifications. The finite element analysis is conducted using NASTRAN, and the probabilistic optimal solutions are obtained via the moving least squares method in the context of RBDO using a response surface me...
Conservative design procedures adopted for nuclear piping systems usually result in stiff piping designs that use excessive support devices such as rigid supports and snubbers. Use of these piping support devices has created safety concerns. This report describes the interim result for a piping research project conducted at Lawrence Livermore National Laboratory (LLNL) for the US Nuclear Regulatory Commission (NRC). The overall objective of this research project is to develop modified design requirements and criteria which will improve piping reliability and minimize the use of pipe supports, snubbers, and pipe whip restraints. The current study was conducted to establish the necessary groundwork for this work based on the piping reliability analysis.
This research project is to develop a technical basis for flexible piping designs which will improve piping reliability and minimize the use of pipe supports, snubbers, and pipe whip restraints. This study indicated that piping design can be made more reliable by some reduction of rigid supports and/or snubbers. This study also confirmed that the malfunction of pipe whip restraints introduced higher thermal stresses and tended to reduce the overall piping reliability. Finally, our results indicated that supports in a flexible piping design may need to be reevaluated and that the elimination of pipe supports which are close to components should be done with care in order to minimize the impact on the component reliability.
Abstract Evaluation of pharmaceutical agents in children is now conducted earlier in the drug development process. An important consideration for this pediatric use is how to assess and support its safety. This article is a collaborative effort of industry toxicologists to review strategies, challenges, and current practice regarding preclinical safety evaluations supporting pediatric drug development with biopharmaceuticals. Biopharmaceuticals include a diverse group of molecular, cell-based or gene therapeutics derived from biological sources or complex biotechnological processes. The principles of preclinical support of pediatric drug development for biopharmaceuticals are similar to those for small molecule pharmaceuticals and in general follow the same regulatory guidances outlined by...
... for duty as Naval Gunfire Liaison Officers in Marine Corps Divisions. ... Regiment, the 82nd Airborne Division, the 101st Airborne Division (Air Assault ...
Physician reimbursement and the coding to support it are critically important to the sustained health of any physician's practice. This article reviews the recent history of physician reimbursement...Full Text Available
There is a mismatch between the documentation of the visually guided behaviors and visual physiology of decapods (Malacostraca, Crustacea) and knowledge about the neural architecture of their...Full Text Available
... and support cost, and post-retirement disposal cost) of ... from reactors, and the reactors and other ... the ship's hull and reactor compartment enough to ...
Evolution in Space Radio Telescopes Reveal Youngest Stellar Corpse Gas Clouds in Whirlpool Galaxy Yield Important Clues Supporting Theory on Spiral Arms Starbust-driven Winds...
Jun 20, 2011 ... NASA and the Defense Advanced Research Projects Agency (DARPA) are offering high school students the opportunity to design experiments ...
...Systems, UWA investigating rate uplift effects of shallow foundation systems associated with high voltage transmission line support towers. This work was funded by National Grid, ...
... WHS- Washington Headquarters Service ... but also with respect to other Joint, National and ... unit of action (UA) combat team or task force is organized ...
A method for determining the rational capacity of the shield supports under various geological conditions is proposed. Based on the instrumentation of the pressure histories of the shield legs in eight mines, the relation between the final load or the increment of support resistance in a mining cycle and the setting load is established. The relation is represented by a mathematical equation with characteristic constants. Those constants are related to the physical properties of the immediate and main roof strata. Nomographs were constructed for determining the constants under various geological conditions. The paper discusses the principles and step-by-step procedures for determining the rational setting and yield loads for all the shield supports employed in the eight mines. The predicted values are then compared with the actual ones used by the operators. 7 refs., 6 figs., 4 tabs.
... centers in materials research. MRSECs address fundamental materials research topics of intellectual ... in materials research. II. PROGRAM DESCRIPTION MRSECs are supported by NSF to undertake materials ...
... of Award Costs (Schedule A), are free of material misstatement. An audit includes examining, on a ... support costs, materials and supplies, and the indirect costs. We found two material internal ...
... Joint Meritorious Award to DLA," Dimnsions Vol. ... recently the Defense Finance Accounting Services (DFAS ... gmbAt Service SUoDort Field Manual. ...
aluminum electrolytic capacitors with Freon, trichloroethylene, carbon tetrachloride, or other chlorine or fluorine solvents. Aluminum electrolytic ...
The current research addressed age differences in internet use among Same Sex Attracted (SSA) individuals. In general, online communities are found to be a source of social support, especially for minority group members. However, it is unclear whether younger and older SSA people differ in their use of these communities. The present research examined age differences in use of online communities, hypothesizing that young SSA people primarily use these for social interaction and support, whereas older SSA people use online communities to seek sexual contacts. Study 1 examined age differences in motives to start using these websites. Study 2 examined age differences in use of online profiles and online social support. Results of both studies confirmed our hypotheses. Younger compared to older...
North Carolina A and T State University has completed the development of an infrastructure for the interdisciplinary Waste Management Institute (WMI). The Interdisciplinary Waste Management Institute (WMI) was approved in June, 1994 by the General Administration of the University of North Carolina as an academic support unit with research and public service functions. The mission of the WMI is to enhance awareness and understanding of waste management issues and to provide instructional support including research and outreach. The goals of WMI are as follows: increase the number of minority professionals who will work in waste management fields; develop cooperative and exchange programs involving faculty, students, government, and industry; serve as institutional sponsor of public awareness workshops and lecture series; and support interdisciplinary research programs. The vision of the WMI is to provide continued ...
This is a presentation on Human Factors in reactor operations. It discusses issues that deal with power plant operations, training and design, operational effectiveness and safety, supporting people to achieve effective and error free performance.
We write a space-time Feynman Path Integral representation for scattered wave fields from a weakly/compact supported anisotropic non-homogeneity. (author)
The Buried Waste Integrated Demonstration (BWID) is a program of the Department of Energy (DOE) Office of Technology Development whose mission is to evaluate different new and existing technologies and determine how well they address DOE community waste remediation problems. Twenty-three Technical Task Plans (TTPs) have been identified to support this mission during FY-92; 10 of these have identified some support requirements when demonstrations take place. Section 1 of this report describes the tasks supported by BWID, determines if a technical demonstration is proposed, and if so, identifies the support requirements requested by the TTP Principal Investigators. Section 2 of this report is an evaluation identifying facility characteristics of existing Idaho National Engineering Laboratory (INEL) facilities that may be considered for use in BWID technology demonstration activities.
Periodontitis is an infectious process characterized by inflammation affecting the supporting structures of the teeth. Porphyromonas gingivalis is a major oral bacterial species implicated...Full Text Available
Sep 5, 1996 ... In Haiti, the military deployed a space support team to advise the task force commander on the effective use of space assets, such as the Milstar ...
Purpose.There is a paucity of neuron replacement studies for retinal ganglion cells. Given the complex phenotype of these neurons, replacement of ganglion cells may be impossible....Full Text Available
This standard establishes requirements, verification criteria, and contractor tasks for electromagnetic effects protection of airborne, ground, and support systems. These effects include electromagnetic compatibility, electromagnetic interference, lightni...
A brief overview is given of the activities in Italy on the subject of electric-powered vehicles, supported by the Commissione Italiana Veicoli Elettrici Stradali (CIVES) in Milan. 3 tabs., 3 figs., 8 refs.
The economics of medical computer networks are presented in context with the patient care and administrative goals of medical networks. Design alternatives and network topologies are discussed with...Full Text Available
... Ward, William E. Brigadier General, Assistant Division Commander (Support), 82nd Airborne Division, Fort Bragg, North Carolina, Chief, Office of ...
Effective teamwork among station work groups is essential for plant production and safety in all phases of plant operation. To achieve effective teamwork, all contributing work groups must have ongoing access to and share a common perspective on station work priorities, and recognize how their individual contributions fit with and support the contributions of other groups in support of the larger station goals. Achieving and maintaining this alignment in perspective across all workgroups can be a challenge in large organizations. This paper discusses the experience at Darlington in building and maintaining station teamwork among the station workgroups in support of day-to-day plant operations. The issues encountered and the resource impacts of specific teamwork supporting practices adopted are outlined. (author)
In this note we describe a support structure which will hold detector systems (ITS, TPC, TOF) inside the large solenoid. An overall view of ALICE detector is shown on Fig.1. The support structure consists of 2 rings which fixed to an iron yoke and spokes which connect TPC and TOF to these rings. The ITS is connected by spokes to TPC end caps. Between coils there are 7cm spacings which will allow to fix rings to the yoke this support structure will allow to assemble ITS, TPC and TOF together (Fig.2) somewhere on the surface and then transport to the pit and install in the magnet. Two rings (1) are connected with four bars (2). On the bottom bars there are rolls (3) which will allow smoothly insert detectors into the magnet. Spokes (4) are uniformly distributed.
This report provides procedures for evaluating metal, consumable, and combustible cartridge cases. It identifies supporting tests, facilities, and equipment required. Subtests include weapon and ammunition preparation, initial inspection, ammunition chara...
Malignancies Breast Malignancies Bladder, Prostate, and Testicular Malignancies Uses of Cancer Registry Data Brain Tumor Reporting Training Materials Overview Presentation and...
... By developing and disseminating educational materials and curricula, supporting the preparation and ... education, such as curriculum or educational materials development, faculty or teacher preparation ...
An epidemiological study about mastitis in French dairy herds, supported by an ecopathological survey is described. The aim of this work was to explain variations of the annual frequencies of...Full Text Available
Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, ...
There are 760 feederpipes, which they are connected to inlet/outlet of the 380 pressure tube channels on the front of the calandria, in CANDU-type Reactor of Wolsung Nuclear Power Plant. As an ISI(In-Service Inspection) and PSI (Post-Service Inspection) requirements, maintenance activities of measuring the thickness of curvilinear part of feederpipe and inspecting the feederpipe support area within calandria are needed to ensure continued reliable operation of nuclear power plant. And ultrasonic probe is used to measure the thickness of curvilinear part of feederpipe, however workers are exposed to radioactivity irradiation during the measurement period. But, it is exposed to radioactivity irradiation during the measurement period. But, it is impossible to inspect feederpipe support area thoroughly because of narrow and confined accessibility, that is , an inspection space between the pressure tube channels is less than 100 mm and pipes in ...
Different cases exist in various countries regarding the institutional status, the organization and the technical resources of the Nuclear Regulatory Authority (NRA): there are NRAs having extended internal technical capability and others relying mostly on external technical support. Considering the research and development activities and the very broad range of technical matters on which the regulatory and licensing activity are based, the NRA can not rely only on internal resources, and generally there is the need of technical and scientific support together with enhanced international cooperation. The international cooperation and networking among NRAs, and their Technical Support Organizations (TSO), represents a fundamental way to maintain competence, capability and knowledge. Within the EU member states this is becoming more and more an institutional duty. In providing technical support for ...
The primary objective of the Air Force Continuous Acquisition and Life-cycle Support (CALS) Test Network (AFCTN) is to evaluate the effectiveness of the CALS standards for technical data interchange and to demonstrate the technical capabilities and operat...
BackgroundMany emergency ambulance calls are for older people who have fallen. As half of them are left at home, a community-based response may often be more appropriate than hospital...Full Text Available
Design considerations are given for the secondary side region of a vertical U-tube nuclear stream generator with an integral preheater. The thermal shield design, the novel recirculating water flow distribution scheme, the high porosity tube supports used in the parallel flow regions, and the U-bend supports are discussed for the Wolsung Plant steam generators. Experimental and analytical development programs undertaken to verify the design features are outlined.
The document describes the statistical analyses of data on pollutant loadings in effluent wastestreams from pulp, paper, and paperboard facilities. Included are the analyses that support the revised subcategorization and proposed effluent limitations for biochemical oxygen demand and total suspended solids based upon the best practicable control technology currently available.
Prompted by a $10 million Congressional allocation to identify supplemental actions to protect the Columbia River from groundwater contamination beneath the Hanford Reservation, the U. S. Department of Energy (DOE) Environmental Management (EM) Office of Clean-up Technology identified twenty-three potential technical projects and then down-selected ten of these for further evaluation. An independent expert peer review was conducted for the ten down-selected proposals. The review panel consisted of twenty-three recognized subject matter experts that broadly represented academia, industry, and federal laboratories. Of the initial ten proposals reviewed, one was given unconditional support, six were given conditional support, and three were not supported as proposed. Three additional proposals were then submitted by DOE for review--these proposals were structured, in part, to respond to the initial round of technical peer ...
This report presents information and analysis to assist BLM in clarifying oil shale research needs. It provides technical guidance on research needs in support of their regulatory responsibilities for onshore mineral activities involving oil shale. It provides an assessment of research needed to support the regulatory and managerial role of the BLM as well as others involved in the development of oil shale resources on public and Indian lands in the western United States.
...this page document analysis carried out during the policy development of the CRC Energy Efficiency Scheme. policy, background, carbon, reduction,...commitment, energy efficiency, CRC, Policy background Spending Review Announcement In the October 2010 Spending Review, the UK Government announced that the CRC ... Revenue from the sale of CRC allowances, totalling ٟ billion a year by 2014/15, will be used to support ... The implications of this announcement for CRC are: In order to clarify the price signal to participants and to support the public ...
The report presents selected highlights of how research has contributed to the regulatory effort. It explains the research role of the NRC and nuclear safety research contributions in the areas of: pressure vessel integrity, piping, small- and large-break loss-of-coolant accidents, hydrogen and containment, source term analysis, seismic hazards and high-level waste management. The report also provides a summary of current and future research directions in support of regulation.
Assisted users with expired passwords Closed 233 NCICB Support Wizard Accounts Tickets Set up Resource Accounts for individual developers to control and track access on QA Application servers Maintained daily account synchronization between GForge project developers and CVS write access accounts Created FTP and SFTP user accounts for TCGA test, analysis datasets downloads and analysis datasets management.
A composition of matter to treat particles entrained in flue gas, is described comprising: a caustic liquid used to adjust resistivity of the entrained particles; and inert particulate matter supporting the caustic liquid for inhibiting chemical action of the caustic liquid until used to adjust the resistivity of the entrained particles, the inert particulate matter supporting sufficient caustic liquid to adjust the resistivity of the entrained particles.
As the Operating and Support staffs of the FFTF organization have gained experience, the plant reliability and capacity factors have shown a steadily improving trend. The plant capacity factor for Cycle 4 was 99.5%. It is the purpose of this report to describe the evolution of the maintenance organization at the FFTF site from a general support organization to a technically proficient organization playing a major role in planning and performance of plant maintenance evolutions.
The ankle plantar flexor muscles, gastrocnemius (Gas) and soleus (Sol), have been shown to play important roles in providing body support and forward propulsion during human walking. However, there...Full Text Available
... The final strand is to invest in new infrastructure, supporting the growth of small and medium-sized businesses and developing new productive industries like pharmaceuticals, locomotive engineering and plastics. Having acted as an adviser to the government, I can see several reasons why the EU should welcome and support this model of economic development. The most important is that Kazakhstan's diversification and its determination to move production up the ...
A broad-based, multidisciplinary research program is being conducted to study biological effects of electric and magnetic fields from high-voltage transmission lines. Assistance and technical support for this program are reported. (DLC)
... For example, moving from incentives for deepwater drilling for dirty oil to real support for renewables, and from hidden subsidies for nuclear power to transforming the UK to a thriving low carbon economy. Thanks once again to those who came along. There will be more opportunities to campaign with us soon, to help get the support we need to move the UK beyond oil. GoBeyondOilCampaigningCamden1 Comments(...
The Training Department at the Point Lepreau GS has been developing and improving its training for technical support staff. A generic set of objectives are being used as the basis for a systematic approach to training. The program covers general and job specific knowledge and skills using a mix of classroom instruction, mentoring and continuing training seminars. This paper describes experience, success and the challenges in the development, delivery and evaluation of the training program. (author)
DescriptionFollowing publication of the Curry report, DEFRA have made a commitment to establish a number of pilot projects supporting a network of demonstration and development farms. These 'farms' are intended to support the process of technology transfer by giving free access to information on the practical application of new, emerging and best practice technologies. Protected Horticulture has been identified as a sub-sector requiring the establishment of one of these projects. One of the major pressures [continued...
There are 760 feederpipes, which they are connected to inlet/outlet of the 380 pressure tube channels on the front of the calandria, in CANDU-type Reactor of Wolsung Nuclear Power Plant. As an ISI(In-Service Inspection) and PSI (Post- Service Inspection) requirements, maintenance activities of measuring the thickness of curvilinear part of feederpipe and inspecting the feederpipe support area within calandria are needed to ensure continued reliable operation of nuclear power plant. And untrasonic probe is used to measure the thickness of curvilinear part of feederpipe, however workers are exposed to radioactivity irradiation during the measurement period. But, it is impossible to inspect feederpipe support area thoroughlv because of narrow and confined accessibility, that is, an inspection space between the pressure tube channels is less than 100mm and pipes in feederpipe support area are congested. And also, workers ...
The objective of SCK-CEN's R and D programme on decision strategy research are (1) to support and advise the Belgian authorities on specific problems concerning existing and potential hazards from exposure to ionising radiation, both in normal and emergency situations; (2) to perform research on relevant topics that might have an important impact on decision making related to nuclear applications, including social and economic sciences. Main achievements in this area in 1999 are described.
The Department of Energy has used its seldom-used statutory authority and filed comments with the Federal Energy Regulatory Commission urging support for Public Service Company of Indiana's request that the FERC allow it to sell up to 450 megawatts of firm power to eligible wholesale purchasers at negotiated or market-based rates in exchange for open transmission access for other generators.
The involvement and relationship of carbon steel corrosion products in the tube denting phenomenon promoted an intensive research effort to: 1) understand, reproduce, and arrest the denting process, and 2) evaluate alternative tube support materials to provide additional corrosion resistance. The paper summarizes a corrosion testing program for the verification of type 405 stainless steel under acid or all volatile treatment conditions.
A process is provided for conducting organic compound conversion over a catalyst composition comprising a supported crystalline zeolite having a high initial silica-to-alumina mole ratio, said supported zeolite being prepared by compositing said crystalline zeolite with alumina, reacting the composite with a particular hydrogen fluoride solution in a specified way, drying the hydrogen fluoride reacted composite, treating the dried composite by hydrolysis, ammonolysis and/or by contact with an ammonium salt solution, and calcining the resulting material.
A review and a number of extracts are given of the statement made by the acting chairman of the CEGB at a press conference on the publication of documents in support of the case for the building of the proposed Sizewell B PWR. The documents comprise the CEGB Statement of Case proper, the Reference Design, the Pre-Construction Safety Report and some 300 supporting reports. Objectors have eight months to study the reports before the public inquiry into the CEGB's proposals due to open in January 1983.
Clostridium thermoaceticum ATCC 39073 converted vanillate to catechol. Although carboxylated aromatic compounds which did not contain methoxyl groups were not by themselves growth supportive, protocatechuate...Full Text Available
In the WWER-440 reactor the primary piping consists of six horizontal loops going radially from the pressure vessel, each loop having a horizontal steam generator. In this reactor type the relatively long primary piping with many curved sections requires special attention in order to successfully eliminate the consequences of the design basis accident. Emergency supports are located in appropriate places to restrict the movements of the pipe in 1, 2, 3 or 4 directions depending on the geometry of the pipe near the support. Under normal conditions there is a gap of some centimeters between the pipe and a support so that the pipe can be deformed freely under changing loads. In order to analyse the behaviour of the broken piping system with the support structures a computer code called PIPEBREAK has been written. The main objects in the analyses have been to calculate the deformations of the ...
The aim of this work is to test the catalytic oxidation of pyridine over zeolite-supported catalysts and to compare the difference in their activities for the oxidation of pyridine. The catalytic oxidation of pyridine pollutant on a series of copper-supported catalysts, inclusive of Cu/beta, Cu/ZSM-5, Cu/MCM-41 and Cu/{gamma}-Al{sub 2}O{sub 3}, in the presence of excess oxygen was studied. The activity of the copper-supported catalysts for the pyridine oxidation could be correlated with the binding energy of oxygen coordinated to metal copper, while the ability to control the yield of NO{sub x} appeared to be strongly dependent on the binding energy of NO bonded to metal copper. On these catalysts, two copper species, Cu(H{sub 2}O){sub 6}{sup 2+} ions and CuO were identified, in which Cu{sup 2+} ions had higher activity for the NO{sub x} control but poorer activity for the pyridine oxidation. Amongst those ...
The fourth in a series of international Leak-Before-Break (LBB) Seminars supported in part by the US Nuclear Regulatory Commission was held at the National Central Library in Taipei, Taiwan on May 11 and 12, 1989. The seminar updated the international polices and supporting research on LBB. Attendees included representatives from regulatory agencies, electric utilities, nuclear power plant fabricators, research organizations, and academic institutions. Regulatory policy was the subject of presentations by Mr. G. Arlotto (US NRC, USA) Dr. B. Jarman (AECB, Canada), Dr.P. Milella (ENEA-DISP, Italy), Dr. C. Faidy (EDF/Septen, France ), and Dr. K. Takumi (NUPEC, Japan). A paper by Mr. K. Wichman and Mr. A. Lee of the US NRC Office of Nuclear Reactor Regulation is included as background material to these proceedings; it discusses the history and status of LBB applications in US nuclear power plants. In addition, several papers on the ...
Activities are reported by the Reactor Systems Section, Research Instrument Section, and the Measurement and Controls Engineering Section. Reactor system activities include dynamic analysis, survillanc and diagnostic methods, design and evaluation, detectors, facilities support, process instrumentation development, and special assignments. Activities in the Research Instrument Section include the Navy-ORNL RADIAC development program, advanced ..gamma.. and x ray detector systems, neutron detection and subcriticality measurements, circuit development, position-sensitive detectors, stand-alone computers, environmental monitoring-detectors and systems, plant security, engineering support for fusion energy division, engineering support for accelerator physics, and communications: radio, closed-circuit tv, and computer. Activities in the Measurement and Controls Engineering Section include the AVLIS program; gas centrifuge ...
This patent describes a process for preparing of an ion exchanger, comprising: treating an ionically inert activated charcoal porous support with an aqueous solution of metal oxychloride selected from the group consisting of zirconium and titanium oxychlorides so as to impregnate the pores of the support with the solution; separating the treated support from excess metal oxychloride solution; converting the metal oxychloride to a hydrous metal oxide precipitate in the pores of the support at a pH above 8 and above the pH whereat the hydrous metal oxide and activated charcoal support have opposite zeta potentials and sufficient to hydrolyze the metal oxychloride. It also describes a process for preparing an ion exchanger comprising: treating granulated activated charcoal with a concentrated solution of a metal oxychloride from the group consisting of zirconium and titanium ...