Energy Technology Data Exchange (ETDEWEB)

It has become necessary to investigate the feasibility and desirability of joint coking of residues from the processing of petroleum and shale oil. Experiments have been performed on different types of feedstocks: a shale oil residue (SO) with an initial boiling point of 350/sup 0/C, obtained by thermal destruction of Bulgarian shales with a solid heat-carrier; a pyrolysis tar from the production of ethylene; extracts obtained in solvent treatment of petroleum oils, namely extracts from medium-viscosity lube distillate, viscous distillate, and residual lube stock; and asphalt obtained in deasphalting. Each of the petroleum products was blended with the SO in a 1/1 ratio.

Energy Technology Data Exchange (ETDEWEB)

Acidic constituents in crude oil are associated with the formation of stable emulsions during production and present a challenge for efficient oil recovery and processing. Acid molecules, including naphthenic acids and acidic sulfur in crude oil cause corrosion in refineries and pipelines. Naphthenic acids are also significant because of their surface activity and marginal water solubility, so that they may leach to wastewaters and cause adverse environmental effects. Acidic components of oil are not limited to carboxylic acids but also molecules that contain sulfur and nitrogen. As such, an improved understanding of the chemistry and physics of petroleum at the molecular level is needed in order to understand the range of problems associated with acidic oil components and to design better solutions. The applications of negative-ion electrospray ionization (ESI) Fourier transform ion cyclotron resonance mass spectrometry ...

Energy Technology Data Exchange (ETDEWEB)

Biocatalytic Desulfurization (BDS) represents an alternative approach to the reduction of sulfur in fossil fuels. The objective is to use bacteria to selectively remove sulfur from petroleum and middle distillate fractions, without the concomitant release of carbon. Recently, bacteria have been developed which have the ability to desulfurize dibenzothiophene (DBT) and other organosulfur molecules. These bacteria are being developed for use in a biocatalyst-based desulfurization process. Analysis of preliminary conceptual engineering designs has shown that this process has the potential to complement conventional technology as a method to temper the sulfur levels in crude oil, or remove the recalcitrant sulfur in middle distillates to achieve the deep desulfurization mandated by State and Federal regulations. This paper describes the results of initial feasibility studies, sensitivity analyses and conceptual design work. ...

International Nuclear Information System (INIS)

Plant Assessment Technology (PAT) group, in association with Intelligent System (IS) Group and Engineering Services Department of Malaysian Institute for Nuclear Technology Research (MINT) has developed gamma scanning facilities for on-line investigation of industrial process columns and vessels. The technology, based on the principle of gamma-ray absorption, has been successfully applied for troubleshooting of a number of distillation columns and process vessels in petroleum refineries, gas processing plants and chemical plants in the country and the region. This paper outlines basic characteristics of the system and describes the inspection procedures, and in addition, case studies are also presented. The case studies are purposely chosen to illustrate the versatility of the technology, and furthermore to demonstrate the economic benefits which can be realised from the application of this technology. (author)

Energy Technology Data Exchange (ETDEWEB)

In the development of the specific mathematical modeling for heavy and ultra heavy petroleum fractions in a molecular distiller is very important the definition of physical and chemical parameters as density and specific heat of the mixture, the enthalpy of vaporization, among others, since they are used in the energy balance. Information on these properties and their variation with temperature are found in the open literature for mixture with few components (simple mixtures). However, for multicomponent solutions consisting of complex mixtures such as oil and its heavy and ultraheavy fractions, available data are few, or are limited to low temperatures. The specific heat is an important property in the energy balance. This property can be measured by Differential Scanning Calorimetry (DSC), which gives results with great sensitivity and accuracy. This paper presents the variation of specific heat with the temperature of ultra-heavy oil ...

Norwegian Open Research Archives (NORA)

Full Text Available

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

In the past three years, we followed the work plan as we suggested in the proposal and made every efforts to fulfill the project objectives. Based on our large amount of creative and productive work, including both of experimental and theoretic aspects, we received important technical breakthrough on naphthenic acid removal process and obtained deep insight on catalytic decarboxylation chemistry. In detail, we established an integrated methodology to serve for all of the experimental and theoretical work. Our experimental investigation results in discovery of four type effective catalysts to the reaction of decarboxylation of model carboxylic acid compounds. The adsorption experiment revealed the effectiveness of several solid materials to naphthenic acid adsorption and acidity reduction of crude oil, which can be either natural minerals or synthesized materials. The test with crude oil also received promising results, which can be potentially ...

British Library Electronic Table of Contents (United Kingdom)

We have recently introduced several important improvements in the measurement of distillation curves for complex fluids. This new method is a significant improvement over current approaches, with features including a composition-explicit data channel for each distillate fraction (for both qualitative and quantitative analysis), trace chemical analysis of each distillate fraction, and a corrosivity assessment of each distillate fraction. In the present contribution, we present the application of the advanced distillation curve method to a bio-derived crude oil prepared from swine manure. One motivation behind the work was to precisely measure the distillation curve of the oil derived from swine manure with our advanced distillation apparatus and compare the bio-derived oil to traditional pe...

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Four advanced oxidation processes (UV/TiO2, UV/IO4^-, UV/S2O8^2^-, and UV/H2O2) were tested for their ability to mineralize naphthenic acids to inorganic carbon in a model oil sands process water containing high dissolved and suspended solids at pH values ranging from 8 to 12. A medium pressure mercury (Hg) lamp was used, and a Quartz immersion well surrounded the lamp. The treatment goal of 5mg/L naphthenic acids (3.4mg/L total organic carbon (TOC)) was achieved under four conditions: UV/S2O8^2^- (20mM) at pH 8 and 10, and UV/H2O2 (50mM) at pH 8 (all with the Quartz immersion well). Values of electrical energy required to meet the treatment goal were about equal for UV/S2O8^2^- (20mM) and UV/H2O2 (50mM) at pH 8, but three to four times larger for treatment by UV/S2O8^2^- (20mM) at pH 10. ...

Energy Technology Data Exchange (ETDEWEB)

It turns out of interest to Comision Federal de Electricidad and Petroleos Mexicanos to reduce costs of fuel oil, reducing the viscosity of the residues petroleum of high vacuum distillation emulsifying these with water. The parameters that define the characteristics of the emulsions are mainly the relation of their components, viscosity, size and drop distribution and its stability. The experimental work began producing emulsions in form of lots, using samples of approximately 500 milliliters of vacuum residue. In this first stage, at different concentrations, were examined eight different surfactants, as well as combinations among them, also seven different stabilizers were used. With these tests it has been managed to identify the concentrations, as well as the most adequate relations of surfactants and stabilizers for the production of emulsions of vacuum residues in water. The size and drop distribution has been determined by means of an ...

Science.gov (United States)

Describes laboratory and industrial tests on the use of lowasash sulphurous petroleum coke during reduction of barite. Shows the potential of substituting blast furnace coke with petroleum/coke fines in this process.

Energy Technology Data Exchange (ETDEWEB)

Petroleum, known to be a source of a vast variety of organic compounds, is also a depository of valuable mineral components. Vanadium and nickel are the most important metal components of crude petroleum, with their concentrations reaching a few tenths of a percent. Their percentage increases 2- to 5-fold in the hydrocarbon products. The vanadium content in processed petroleum products is given. Therefore, the extraction of metals from petroleum is becoming an increasing important task. At present, there is no petroleum processing technology aimed solely at obtaining organic components. The occurrence of metals and other trace elements in petroleum and hydrocarbon products is discussed on the basis of available literature and experimental data. Techniques for isolating metals from petroleum and hydrocarbon products and their quantitative ...

Energy Technology Data Exchange (ETDEWEB)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

We have recently introduced several important improvements in the measurement of distillation curves for complex fluids. The modifications include a composition-explicit data channel for each distillate fraction (for both qualitative and quantitative analysis) and corrosivity assessment of each distillate fraction. The composition-explicit information is achieved with a new sampling approach that allows precise qualitative as well as quantitative analyses of each fraction, on the fly. We have applied the new method to a variety of fluids, including simple n-alkanes, rocket propellant, gasoline, jet fuels, and a hydrocarbon fluid made corrosive with dissolved hydrogen sulfide. In the current contribution, we present the application of the advanced distillation curve method to two samples of crude oil. A primary motivation behind the work is to precisely measure the distillation ...

Energy Technology Data Exchange (ETDEWEB)

Reclaimed Energy Company, Inc., Connersville, IN, receives waste generated from a wide variety of industrial applications which include paint, printing and degreasing companies. The wastes are stored in separate tanks and then distilled in batches (pot distillation). The recovered solvents can be returned to the originator. The residue, left after the solvents are distilled, is disposed of using an environmentally safe, economical procedure. The company worked with an engineering and fabrication firm to develop a continuous processing system that employs a mechanically agitated thin-film evaporator to distill the solvents. Successful performance of the evaporator was ensured by processing samples of solvents through the evaporator manufacturer's pilot plant facilities before the full-sized system was designed. Reclaimed Energy Company, Inc., has realized a number of advantages by going from pot ...

British Library Electronic Table of Contents (United Kingdom)

Abstract: The recent National Academy of Sciences report on forensic sciences states that the study of fire patterns and debris in arson fires is in need of additional work and eventual standardization. We discuss a recently introduced method that can provide predicted evaporation patterns for ignitable liquids as a function of temperature. The method is a complex fluid analysis protocol, the advanced distillation curve approach, featuring a composition explicit data channel for each distillate fraction (for qualitative, quantitative, and trace analysis), low uncertainty temperature measurements that are thermodynamic state points that can be modeled with an equation of state, consistency with a century of historical data, and an assessment of the energy content of each distillate fraction...

British Library Electronic Table of Contents (United Kingdom)

In previous work, several significant improvements in the measurement of distillation curves for complex fluids were introduced. The modifications to the classical measurement provide for (1) temperature and volume measurement(s) of low uncertainty, and most important, (2) a composition-explicit data channel in addition to the usual temperature?volume relationship. This latter modification is achieved with a new sampling approach that allows precise qualitative as well as quantitative analyses of each fraction, on the fly. In the new approach, the distillation temperature is measured in two locations. The temperature is measured in the usual location, at the bottom of the take-off in the distillation head, but it is also measured directly in the fluid. We have further modified our developm...

Energy Technology Data Exchange (ETDEWEB)

Crude N,N-dialkylcarbamoylmethylphosphonates and phosphine oxide extractants, and particularly crude dihexyl N,N-diethylcarbamoylmethylphosphonate and octylphenyl N,N-diisobutylcarbamoyl phosphine oxide, are purified by distilling the crude materials in a thin film evaporator. Preferably, the crude materials are reacted with concentrated hydrochloric acid and then with aqueous sodium hydroxide prior to distillation in the thin film evaporator to hydrolyze impurities contained in them. The purified extractants are useful for extracting actinides and lanthanides from liquid waste streams. (author).

Energy Technology Data Exchange (ETDEWEB)

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N{sub 2} and H{sub 2}-D{sub 2} distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N{sub 2} distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H{sub 2}, HD, D{sub 2}, HT, DT, T{sub 2}) distillation column showed good performance after comparison with the result of a JAERI code, and a H{sub 2}-D{sub ...

Energy Technology Data Exchange (ETDEWEB)

The subject of this paper is based on necessity to register occurrence in petroleum industry. Specifically we are making reference about Exploration and Production at petroleum industry, using a photography as job instrument. The PETROBRAS - Petroleo Brasileiro S.A., apply the photography resources in almost all service. The Campos basin Exploration and Production, responsible for 70% Brazil's petroleum production, utilizes photographies in many solutions. This paper is based on the following premises: the photography as register way; the information facility; the technical applies; the use of this register in the academic, scientific and operational ways. (author)

Energy Technology Data Exchange (ETDEWEB)

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, an improved version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multicomponent gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines (3-50 atm, 650-1200K, stoichiometric fuel/air mixtures). Simulation results ...

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

International Nuclear Information System (INIS)

The study reports the identification of different organic acids that are formed during the pyrohydrolysis of mixed carbide of uranium and plutonium using ion chromatography (IC). The identification of organic acids present in the pyrohydrolysis distillate is required to carry out interference free analysis of Cl and F. The study describes three stage isocratic separations with NaOH eluents having concentrations 2 mM, 10 mM and 50 mM respectively in order to separate and identify both aliphatic and aromatic acids. The present investigation identified formic, acetic, propionic, butyric, tartaric and oxalic acids in the distillate, however, aromatic acids could not be identified. (author)

Energy Technology Data Exchange (ETDEWEB)

Samples from a burning bituminous coal seam from Coalspur, Alberta, were studied by reflected light microscopy. Two zones - namely oxidation- combustion and distillation - were detected in the seam. Near the surface, the oxidation zone contained chars showing cracks and oxidation rims. The cracks were filled with fluorescing hydrocarbon material formed by thermal cracking of coal macerals. The chars in the deeper part of the oxidation zone had a carbonized matrix and burnt rims. The distillation zone covered most of the coal seam. Chars were mostly in the precarbonization stage, except those immediately below the combustion zone or near the base of the seam. Precarbonized chars contained pyrolytic carbon in some horizons. The distilled chars were formed by heat generated by combustion at the top of the seam and also by heat transfer from an underlying burning seam through an intermediate clastic layer. The minimum ...

Science.gov (United States)

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose o...

Science.gov (United States)

the Advanced Distillation Curve, Energy & Fuels, Vol. 22, No. 2, pp. 11041114. http://pubs.acs.org/doi/full/10.1021/ef700562c. Lemmon, E. W., Huber, M. L., ...

Energy Technology Data Exchange (ETDEWEB)

Mild hydrotreating is the key to successful re-refining of used lubricating oils. Coupled with pre-distillation and metals removal, the process produces oil of superior color and clarity with acceptable viscosity and heteroatom content. Furthermore, the entire process provides operational simplicity, economic feasibility and environmental attractiveness. Re-refining preserves a valuable resource while solving a potential environmental problem. Increased sensitivity to disposal of hazardous material once again makes re-refining almost a necessity. Various technologies developed to re-refine used lubricating oils range from simple acid/clay contacting to complex solvent extraction. Most technologies require similar capital investment; however, operating costs vary substantially. Current technology seems to converge on a two-step procedure: distillation of dehydrated used oil in a thin-film evaporator, and subsequent hydrotreating of ...

Energy Technology Data Exchange (ETDEWEB)

This paper examines the dynamic international political economic environment in which petroleum exploration and production companies must operate when considering investments in the economically transitional nations of the former Soviet Union or developing nations In this period of critical global changes low oil prices is only one factor with which petroleum companies Must be. concerned in their investment decisions Other factors include the transition from a bipolar world to a multipolar world of free trade zones. the general malaise of the international economy public and political recognition that nations and industries can no longer practice environmental {open_quotes}beggar-thy-neighbor{close_quotes} policies, and the rejection of aggregate national economic growth policies for sustainable economic development policies in both the Developed and developing world This paper focuses on actions which investing petroleum ...

Energy Technology Data Exchange (ETDEWEB)

Results are given for deep-level petroleum and gas drilling probes in various coastal zones of Southern Sakhalin covering the Poronai depression and the Aniv Bay trough. The exploratory probes indicate that the Middle Miocence deposits of the Boundary trough contain commercial-size deposits of petroleum, that commercial-size gas deposits are in the upper Myocene deposits of the Aliv Bay trough, and that the upper Cretaceous and Cenozoic deposits of the eastern section of Southern Sakhalin lack folded deformations. 7 references, 2 figures.

Energy Technology Data Exchange (ETDEWEB)

Some Japanese and US coal liquefaction research projects are listed.

Science.gov (United States)

and used to reduce or replace petroleum-based transportation fuel, heating oil or jet fuel). In addition, this rule includes a new regulatory provision establishing a...

Science.gov (United States)

of refined petroleum and energy traders have stopped sales of refined product to Iran. Jet fuel suppliers are now refusing to supply jet fuel to Iran Air at most destinations in...

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

International Nuclear Information System (INIS)

The petroleum and petroleum products increase offer a real development opportunity to the alternative fuels. In the context of the french energy accounting increase, the energy independence notion incites the government to promote these new fuels. If the LPG seems declining because of the accident risks fear, the fuel cell is not for today. Near these two sectors what is the future of the biofuels and the natural gas vehicle or the electric cars? (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age hardening and moisture susceptibility was conducted by Western Research Institute (WRI). The ESO residue, have a viscosity of 23.9 Pa{lg_bullet}s at 60{degree}C (140{degree}F), was blended with three different petroleum-derived asphalts, ASD-1, AAK-1, and AAM-1, which are known to be very susceptible to oxidative aging. Rheological and infrared analyses of the unaged and aged asphalts and the blends were then conducted to evaluate oxidative age hardening. In addition, the petroleum-derived asphalts and the blends were coated onto three different aggregates, Lithonia granite (RA), a low-absorption limestone (RD), and a siliceous Gulf Coast gravel (RL), and compacted into briquettes. Successive freeze-thaw cycling was then conducted to evaluate the moisture susceptibility of the prepared briquettes. The rheological analyses of the unaged ...

Science.gov (United States)

When withdrawing a fluid sample (for additional chromatographic analyses) from an apparatus operated at a reduced pressure, a typical syringe proves to be ineffective (even if it is equipped with a gas tight plunger). It simply does not create enough pressure differential to remove a fluid sample from a reduced pressure environment. We encountered such a situation as part of efforts to extend the operation of the advanced distillation curve protocol to reduced pressures. The problem was solved by the development of a pressure balance syringe that allows reliable and precise sampling from an apparatus operating at sub-ambient pressures. This new device uses an external vacuum source to evacuate a syringe barrel, allowing a user to withdraw fluid samples from environments with pressures as low as 0.5kPa. To demonstrate the operation of the newly developed device, distillate analyses were performed on two fluids at low pressure: a predefined ...

British Library Electronic Table of Contents (United Kingdom)

Complex fluids have long posed a significant challenge in our ability to characterize and model fluid properties. Here, we consider complex fluids to be mixtures with many components that can differ significantly in polarity and polarizability. The penultimate complex fluid is crude oil, although many other fluids such as finished fuels are also highly complex. We have recently introduced a measurement strategy that can simplify these efforts and provides the added potential of linking chemical composition (i.e. analytical) information with physical property information. In addition to chemical characterization, the approach provides the ability to calculate thermodynamic and transport properties for such complex heterogeneous streams. The technique is based on the advanced distillation cu...

Energy Technology Data Exchange (ETDEWEB)

Naval Petroleum Reserve No. 1 (NPR-1) in California and Naval Petroleum Reserve No. 3 (NPR-3) in Wyoming continued to be operated at their maximum efficient rates of production during FY 1983. The Government-owned portion of Naval Petroleum Reserve No. 2 in California continued to be leased to private operators as it has been for over 50 years, with the Government receiving a royalty share of production from the leases. All of the Government's share of crude oil produced at the Petroleum Reserves during FY 1983 was sold to the Department of Defense, while natural gas and natural gas liquids were sold competitively on the open market. FY 1983 revenues from the three Naval Petroleum Reserves totaled over $1.5 billion in general receipts and Windfall Profit Taxes. Program expenditures totaled approximately $220 million. The drilling of new wells continued to be an important ...

Energy Technology Data Exchange (ETDEWEB)

Beginning in 1972 low-pressure cables filled with MN-4 oil produced by the Yaroslav Petroleum Processing Plant arrived at the Leningrad Cable Network of the Leningrad Rayon Power Administration. Lines formed with these cables have been successfully used. The parameters of the oil in them have not changed with respect to the values present when the lines were placed in operation. However, from here on filling in of the 110 to 220 kV input lines of low and high pressure will be accomplished with MN-4 oil produced by the Gorkiy Petroleum Processing Plant. Because petroleum from various fields and the properties of the oil produced from it are unlike, samples were taken from some elements of the lines filled in with MN-4 oil. The results of the tests are described.

British Library Electronic Table of Contents (United Kingdom)

The present investigation deals with the synthesis of nanostructured nickel ferrite (NiFe2O4) and their liquid petroleum gas-sensing characteristics. The 15-20nm size nickel ferrite has been synthesized at 700degreeC by a simple molten-salt route using sodium chloride as grain growth inhibitor. These nanoparticles exhibit significantly high response towards liquid petroleum gas (LPG) in comparison with ethanol vapor, hydrogen sulfide, ammonia and hydrogen. The gas response towards various gases at their 200ppm concentrations is investigated at 200-450degreeC. Different characterization techniques have been employed, such as differential thermal analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high resolution transmission elec...

Energy Technology Data Exchange (ETDEWEB)

Coal solids (SRC) and distillate oils are combined to afford single-phase blends of residual oils which have utility as fuel oils substitutes. The components are combined on the basis of their respective polarities, that is, on the basis of their heteroatom content, to assure complete solubilization of SRC. The resulting composition is a fuel oil blend which retains its stability and homogeneity over the long term.

Energy Technology Data Exchange (ETDEWEB)

Results of tests on the 1 kg/h continuous reactor for the hydroliquefaction of coal are described. The reactor was operated at 415-435 C and 21 MPa using a continuous stirred reactor with a retention time of about 2 hours. All product oils were recovered by distillation. Sub-bituminous coal was found to give the best product yield. Tests using 5% red mud and 3% improved red mud showed significant increases in oil yield. (4 refs.)

Energy Technology Data Exchange (ETDEWEB)

In this paper, a concept of technology that can be helpful for lowering the negative influence of the synthetic (based on the Solvay process) soda ash plant on the natural environment is presented. We describe the desulphurisation of combustion gases from the factory's power plant, which is based on their absorption in the overflow of distiller waste. The excess of lime milk, which is added in the process of ammonia regeneration from filter liquor, results in a strong alkalinity of distiller waste. The high pH of distiller waste favours absorption of acidic combustion gases. The laboratory-scale tests showed about 80% efficiency of the desulphurisation process. The suspension samples we obtained consist mainly of CaCO{sub 3}. We suggest using the obtained solid phase as an adsorbent-insert in Fluidised Bed Combustion technology (FBC). Based on raw material prices, production costs, and average sell prices of the ...

International Nuclear Information System (INIS)

Most of the petroleum fields in the Norwegian sector of the North Sea are sandstone reservoirs; the oil and gas are trapped in different species of sandstone. But the Ekofisk Field is a chalk reservoir, which really challenges the operator companies. When oil is produced from chalk reservoirs, water usually gets in and the reservoir subsides. The subsidence may be expensive for the oil companies or be used to advantage by increasing the recovery rate. Since 60 per cent of the world's petroleum reserves are located in carbonate reservoirs, it is important to understand what happens as oil and gas are pumped out. Comprehensive studies at the Department of Petroleum Technology and Applied Geophysics at Stavanger University College in Norway show that the mechanical properties of chalk are considerably altered when the pores in the rock become saturated with oil/gas or water under different stress conditions. The processes are ...

International Nuclear Information System (INIS)

Chemoheterotrophic thermophilic bacteria were used to achieve enhanced hydrocarbon degradation during slurry-phase treatment of oily waste sludges from petroleum refinery operations. Aerobic and anaerobic bacterial cultures were examined under thermophilic conditions to assess the effects of mode of metabolism on the potential for petroleum hydrocarbon degradation. The study determined that both aerobic and anaerobic thermophilic bacteria are capable of growth on petroleum hydrocarbons. Thermophilic methanogenesis is feasible during the degradation of hydrocarbons when a strict anaerobic condition is achieved in a slurry bioreactor. Aerobic thermophilic bacteria achieved the largest apparent reduction in chemical oxygen demand, freon extractable oil, total and volatile solid,s and polycyclic aromatic hydrocarbons (PAHs) when treating oily waste sludges. The observed shift with time in the molecular weight distribution of ...

British Library Electronic Table of Contents (United Kingdom)

The chloromethylation reaction of an asphaltite and styrene graft copolymer followed by the amination of the chloromethylated products was optimized. New strongly basic anion exchangers with an exchange capacity of 2.5 mg-equiv/g and a mechanical strength of 93% were prepared.

Energy Technology Data Exchange (ETDEWEB)

The Monthly Energy Review provides an overview of the production, distribution, and consumption of energy derived from petroleum natural gas, coal, electricity, and nuclear energy. It also discusses oil and gas resource development, energy prices, and issues relevant to international energy markets.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The feasibility of removing petroleum hydrocarbons from oil fields produced waters using biological treatment was evaluated under laboratory and field conditions. Based on previous laboratory studies, a field-scale prototype system was designed and operated over a period of four months. Two different sources of produced waters were tested in this field study under various continuous flow rates ranging from 375 1/D to 1,800 1/D. One source of produced water was an open storage pit; the other, a closed storage tank. The TDS concentrations of these sources exceeded 50,000 mg/l; total n-alkanes exceeded 100 mg/l; total petroleum hydrocarbons exceeded 125 mg/l; and total BTEX exceeded 3 mg/l. Removals of total n-alkanes, total petroleum hydrocarbons, and BTEX remained consistently high over 99%. During these tests, the energy costs averaged $0.20/bbl at 12 bbl/D.

Energy Technology Data Exchange (ETDEWEB)

Survey report: The Petroleum Association for the Conservation of the Canadian Environment is an organization of petroleum refiners that works closely with the Canadian government to set realistic air pollution control standards for refinery emissions. To date, the refiners have made a substantial investment in pollution abatement equipment. As a result, there have been no major pollution incidents traceable to refinery emissions. In the future, it will be essential that refiners continue to invest in air pollution abatement measures and continue to cooperate with the government in setting achievable pollution control standards. (1 photo, 1 table)

Energy Technology Data Exchange (ETDEWEB)

The petroleum sector is highly significant for the Norwegian economy. Its share of gross domestic product, exports and total government revenues has been substantial over the past two decades, reaching a particularly high level in 2000 and 2001. The principal reason why revenues were so high in these two years is a combination of high oil prices, a strong USD against the NOK and historically high petroleum production. The share of petroleum investment in total capital spending in the Norwegian economy was at its highest in the early 1990s. Total investment in the petroleum sector has been above NOK 40 bn every year since 1992, and peaked in 1998 at roughly NOK 80 bn. Capital spending declined to around NOK 56.9 bn in 2001. The government's most important revenue sources in recent years have been cash flow from the state's direct financial interest (SDFI) and from taxes. Production of ...

International Nuclear Information System (INIS)

Literature on examples of phytoremediation techniques used in the in-situ remediation of soils contaminated by petroleum hydrocarbons is reviewed. The review includes discussion of the key mechanisms involved in each case, benefits, limitations and costs compared to alternative approaches, including natural attenuation, engineering and bioremediation. Review of the literature led to the conclusion that phytoremediation is an effective method for degrading and containing petroleum hydrocarbons in soil, and confirmed the ability of plants to transfer volatile petroleum hydrocarbons, such as napthalene, from the soil to the atmosphere via transpiration. The primary loss mechanism for the degradation of petroleum hydrocarbons appears to be microorganisms in the rhizosphere of plants. The available information also suggests that plants may degrade petroleum hydrocarbons directly, ...

Science.gov (United States)

An evaluation of eastern shale oil as an asphalt additive to reduce oxidative age hardening and moisture susceptibility is being conducted. An eastern shale oil residue having a viscosity of 1.30 Pa`s at 60{degrees}C (140{degrees}F) was blended with three different petroleum-derived asphalts that are known to be very susceptible to oxidative aging. In addition, blends of the eastern shale oil residue and the petroleum-derived asphalts are being coated onto three different aggregates that are known to be susceptible to water stripping. The oxidative age hardening portion of this study is not complete at this time. To date, information has been obtained on the unaged samples and two of the aged petroleum-derived asphalts (AAD-1 and AAK-1). When complete, this data will include rheological data on the unaged, RTFO-aged, and the RTFO/PAV-aged samples and infrared data on the unaged and RTFO/PAV-aged samples. With respect to the ...

Energy Technology Data Exchange (ETDEWEB)

The Raywell Process Plants unit, which reclaims a wide range of organic solvents, including chlorinated hydrocarbons, is based on thin film evaporation and distillation rather than steam distillation, thus reducing the risk of contamination by water. Henry Balfour and Co.'s Pfaudler Solvent Recovery System gives 96% or better solvent recovery and produces a near-solid waste suitable for landfill disposal; like the Raywell system, it uses a mechanically wiped thin-film evaporator. Midland Oil Refineries uses sa Raywell thin-film evaporator for recovery of waste lubricating oils rather than the conventional sulfuric acid/clay treatment, thus avoiding formation of sulfuric acid sludge waste. The Henry Balfour Bioenergy anaerobic digestion system gives yields of fuel gas with 65-75% methane as high as 0.8 cu m/kg BOD; it achieves 95-98% BOD removal with no pH control or nutrient addition because it separates solids from liquid effluent and ...

Energy Technology Data Exchange (ETDEWEB)

Special CoMo/Al{sub 2}O{sub 3} catalysts were prepared for testing in coal liquefaction: a conventional CoMo/Al{sub 2}O{sub 3} catalyst, one containing Zn as a second promoter and one having the alumina acidified with fluorine. Their activities were compared with that of red mud. The experiments were conducted in a stirred autoclave with a subbituminous coal and solvent (tetralin, anthracene oil or creosote oil) at 425{degree}C and 17 MPa. The liquefaction products were fractionated into oils, asphaltenes and preasphaltenes with pentane, toluene and THF. The Co(Zn)Mo/Al{sub 2}O{sub 3} catalysts have far higher activities than red mud. Zn and fluorine have beneficial effects on the catalyst activity. Coal tar distillates give higher conversions and oil + gas yields than tetralin when the prepared catalysts are used. 17 refs., 7 tabs.

Energy Technology Data Exchange (ETDEWEB)

The paper describes uptake of gaseous lodine-131 on silver impregnated organic resin, Amberlite IR-120, available at the Secondary Steam Generator (S.S.G.) Opening at T.A.P.S. in comparison with activated charcoal. The experiments are conducted in dry and wet conditions by soaking the impregnated resin and activated charcoal in distilled water for wet condition. The paper also describes the iodine sampler specially designed and fabricated for these experiments.

International Nuclear Information System (INIS)

Tritium removal from tritiated heavy water in a PHWR is the most effective way in reducing workers' internal dose and radioactivity emissions from Wolsong NPP. The optimum design of the Wolsung TRF(Tritium Removal Facility) was carried out using an approximate short-cut method with an assumption that the TRF, designed to extract 8 MCi per year of elemental tritium from a heavy water feedstream, uses Liquid Phase Catalytic Exchange (LPCE) front-end process and Cryogenic Distillation (CD) process. 19 refs., 6 figs., 2 tabs. (author).

Energy Technology Data Exchange (ETDEWEB)

The authors investigated phase equilibria in the system carbon dioxide-hexametapol. Vacuum-distilled solvent of ''pure'' grade was used. The solubility of CO/sub 2/ in hexametapol under pressures at various temperatures and the temperature dependence of the Henry's law coefficient is show. It is concluded that the solubility of carbon dioxide in hexametapol in the temperature and pressure ranges corresponding to the operating conditions of industrial equipment for removing CO/sub 2/ from gases conforms to the Krichevskii-II'inskaya equation. The experimental data can be used for equipment design.

Wastenet

... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions Microchemical Engineer... Provides the information chemists and engineers need to evaluate the use of microreactors, covering the technical, operational, and economic considerations for various applications. AU$136.36 ex-GST Terms and Conditions Perry's Chemical Engin... Was: $199.95 inc gst NOW: $129.95 Special Price ...

Wastenet

... Focuses on distillation and packed towers, and presents the methods and fundamentals of plant design along with supplemental mechanical and related data, nomographs, data charts and heuristics. AU$223.45 ex-GST Terms and Conditions CRC Handbook of Chemis... For almost a century this handbook has been updated annually, except for a few wartime years, and has served generations of engineers and scientists. Current daily price AU$209.09 ex-GST Terms and Conditions Perry's Chemical Engin... Was: $199.95 inc gst NOW: ...

Energy Technology Data Exchange (ETDEWEB)

The Monsanto Chemical Company operates a plastics and resins plant located in Addyston, Ohio. The process equipment requires routine rinsing with technical grade acetone between batches. Due to the volumes of spent acetone generated and the associated RCRA hazardous waste regulations, the plant sought to recycle and reuse the acetone to reduce the purchase cost of virgin acetone and the cost of spent acetone disposal. One of the first options explored was package unit distillation units. The cost of these units was in the $20--$30,000 range in 1989 dollars. Even though the cost of a package unit was not deemed unreasonable, there were additional costs and concerns that led to elimination of this option. The unit would have required additional manpower to operate and maintain, i.e., at least a fraction of an operator and mechanic. For plant safety reasons, it was desired to operate this package unit outside the production building, thus construction of an ...

Energy Technology Data Exchange (ETDEWEB)

The Energy Information Administration (EIA) prepares quarterly, short-term energy supply, demand, and price projections for publication in February, May, August, and November in the Short-Term Energy Outlook (Outlook). An annual supplement analyzes the performance of previous forecasts, compares recent cases with those of other forecasting services, and discusses current topics related to the short-term energy markets. (See Short-Term Energy Outlook Annual Supplement, DOE/EIA-0202.) The forecast period for this issue of the Outlook extends from the third quarter of 1993 through the fourth quarter of 1994. Values for the second quarter of 1993, however, are preliminary EIA estimates (for example, some monthly values for petroleum supply and disposition are derived in part from weekly data reported in the Weekly Petroleum Status Report) or are calculated from model simulations using the latest exogenous information available (for example, ...

International Nuclear Information System (INIS)

This conference and trade show provided a forum to present new, emerging and existing technologies that will play a key role in ensuring that hydrocarbon exploitation occurs in a sustainable manner, where costs and resource recovery are optimized while minimizing environmental impacts. The challenge of developing maturing basins, frontier lands and unconventional resources was discussed. In particular, the application of thermal recovery methods such as steam assisted gravity drainage (SAGD) for the in-situ recovery of heavy oils and bitumens was reviewed and compared with the performance of alternative enhanced energy recovery technologies such as vapor extraction (VAPEX). The conference was attended by local and international participants in the petroleum sector, including managers, engineers, technologists, geologists, and other petroleum industry specialists. The conference featured 132 presentations addressing topics such as improved ...

Energy Technology Data Exchange (ETDEWEB)

The growth power-time curves of a strain of petroleum bacteria, B-2, in various kinds of cultures containing different kinds of carbon sources, glucose, n-tetradecane, n-hexadecane and n-octadecane, and different kinds of microemulsions have been determined by using a 2277 Thermal Activity Monitor. The curves showed a single peak for cultures containing a single carbon source, glucose, and two peaks for cultures containing two kinds of carbon sources, glucose and one of the n-alkanes. The first peak indicated that bacteria grew by consuming glucose and the second peak indicated that bacteria grew by consuming n-alkane. The curves were complex when the bacterium grows in a microemulsion culture. According to a kinetic equation of bacterial growth under limited conditions, the rate constants of bacterial growth were obtained. The results showed that the microemulsion culture was more appropriate to bacteria to grow on n-alkanes.

Energy Technology Data Exchange (ETDEWEB)

The removal of paraffinic bottom accumulations from refinery storage tanks represents an increasingly costly area of petroleum storage management. Microorganisms can be used to reduce paraffinic bottoms by increasing the solubility of bottom material and by increasing the wax-carrying capacity of carrier oil used in the cleaning process. The economic savings of such treatments are considerable. The process is also intrinsically safer than alternative methods, as it reduces and even eliminates the need for personnel to enter the tank during the cleaning process. Both laboratory and field sample analyses can be used to document changes in tank material during the treatment process. These changes include increases in volatile content and changes in wax distribution. Several case histories illustrating these physical and chemical changes are presented along with the economics of treatment.

Energy Technology Data Exchange (ETDEWEB)

This report presents the preliminary findings of the first phase of the Environmental Survey of the US Department of Energy's (DOE) National Institute for Petroleum and Energy Research (NIPER), conducted February 29 through March 4, 1988. The Survey is being conducted by an interdisciplinary team of environmental specialists, led and managed by the Office of Environment, Safety and Health's Office of Environmental Audit. Team members are being provided by private contractors. The objective of the Survey is to identify environmental problems and areas of environmental risk associated with NIPER. The Survey covers all environmental media and all areas of environmental regulation. It is being performed in accordance with the DOE Environmental Survey Manual. The on-site phase of the Survey involves the review of existing site environmental data, observations of the operations carried on at NIPER and interviews with site personnel. 35 refs., 8 figs., ...

International Nuclear Information System (INIS)

Various theories and examples of modelling, forecasting and optimization designing in the different parts of the petroleum and gas industries are presented, stochastic programming for long term planning in the refining industry, stochastic model for gasoline blending, feedstock optimization, location and sizing for offshore platforms, hydrocarbon exploration simulation rapid method, valuation of oil field development leases, economic models for petroleum allocation, models for oil supply market, trade embargo game theory, stochastic programming of gas contract portfolio management, scheduling transportation of oil and gas, strategic planning in an oil pipeline company, simulation of offshore oil terminal systems, hierarchical selection of oil and gas distribution systems.

Energy Technology Data Exchange (ETDEWEB)

Research is presented on oil and gas technologies, advanced systems, soil remediation and remediation of acid mine drainage, applied science research in plastics and petroleum coprocessing, and fossil fuel and hydrocarbon conversion using a hydrogen rich plasmas.

International Nuclear Information System (INIS)

This support document summarized the results of botanical surveys conducted as part of a phytoremediation research project that catalogued plants found growing at a petroleum impacted site in Alberta. Phytoremediation refers to the growing of chosen plant species in a polluted site for a period of time in order for the plant to remove contaminants through its natural attributes of absorption, translocation, storage and excretion. Several different plant species with phytoremediation properties are being considered for wide scale bioremediation use. This document described the PhytoPet database which was originally developed as an inventory of plants with phytoremediation capabilities. It was designed to provide easy access to information and help users choose plants with the potential to phytoremediate petroleum hydrocarbons. The information in this document is intended for remediation specialists, site owners and managers as well as ...

Energy Technology Data Exchange (ETDEWEB)

The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.

Energy Technology Data Exchange (ETDEWEB)

This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.

Energy Technology Data Exchange (ETDEWEB)

Stochastic simulation has been employed in petroleum reservoir characterization as a modeling tool able to reconcile information from several different sources. It has the ability to preserve the variability of the modeled phenomena and permits transference of geological knowledge to numerical models of flux, whose predictions on reservoir constitute the main basis for reservoir management decisions. Several stochastic models have been used and/or suggested, depending on the nature of the phenomena to be described. Markov Random Fields (MRFs) appear as an alternative for the modeling of discrete variables, mainly reservoirs with mosaic architecture of facies. In this dissertation, the reader is introduced to the stochastic modeling by MRFs in a generic sense. The main aspects of the technique are reviewed. MRF Conceptual Background is described: its characterization through the Markovian property and the equivalence to Gibbs distributions. The framework for generic ...

International Nuclear Information System (INIS)

This Insight conference was held to review many of the legal aspects, legislation and regulations dealing with abandoned wells within the petroleum and natural gas industry. Remedial actions to rehabilitate the abandoned sites, legal issues in abandonment, obligations of the owner, the industry-sponsored Orphans Wells Program, were some of the topics discussed.

Energy Technology Data Exchange (ETDEWEB)

A brief overview is given of the developments in the Dutch offshore industry where new offshore sites appear to be retrofitted or recycled platforms and contractors take over the work from petroleum companies (e.g. as so-called Floating Production Storage Offloading or FPSO). It is expected that in ten years from now a large number of oil platforms will be disappeared or transported to the Chinese Bohai Sea where a new oil field will be explored.

Science.gov (United States)

Coke production from bitumens, coal, petroleum and lignite is covered in this compilation from worldwide research. Studies on coke oven design, performance, corrosion, and deterioration are cited. Blast furnace coke, additives, quality control, and chemical analysis are discussed. Byproduct recovery from coking processes is included. (This updated bibliography contains 369 citations, 110 of which are new entries to the previous edition.)

Science.gov (United States)

Coke production from bitumens, coal, petroleum and lignite is covered in this compilation from worldwide research. Studies on coke oven design, performance, corrosion, and deterioration are cited. Blast furnace coke, additives, quality control, and chemical analysis are discussed. Byproduct recovery from coking processes is included. (This updated bibliography contains 210 abstracts, 61 of which are new entries to the previous edition.)

Energy Technology Data Exchange (ETDEWEB)

The aim of British coal liquefaction research is to produce premium products such as transport fuels and chemical feedstocks. Government support has been promised for two 25 tpd pilot plants. Badger estimate that the finished products would cost 25% more than petroleum products. Countries with no indigenous oil are likely to commence commercial coal liquefaction soon.

Energy Technology Data Exchange (ETDEWEB)

The Ordos Basin is a typical lapped basin, including three sequences of strata: early Paleozoic, late Paleozoic and Mesozoic, with a total thickness of 4000-6000m. Impermeable sealing beds are well developed at the top and base of the upper Paleozoic sequence, separating it from the Mesozoic and the lower Paleozoic strata to form an independent petroleum system. In this petroleum system, the source rocks are widely distributed coals and dark mudstones occurring in the Carboniferous-lower Permian coal measures, with a thickness of 10-15 and 40-60m, respectively. The reservoirs are mainly early Permian tight sandstones, mostly with a porosity of 4-8% and a permeability of 0.1-1.0x10{sup -3}{mu}m{sup 2}. The regional cap rock is a 100-150m thick mudstone in the upper Permian strata. The structural framework of the basin is a huge asymmetric syncline, dipping gently toward the east and north, and steeply toward the south and west. Well data show ...

Energy Technology Data Exchange (ETDEWEB)

Ternary diagrams are commonly used to provide a graphic representation of equilibrium fluid phase behavior for systems as diverse as distillation columns and miscible gas floods of oil reservoirs. The phase envelope, and the position of the critical point on it, are important to enhanced oil recovery engineers who are involved with miscible gas flood design. In the past, phase equilibrium data were laboriously plotted on the ternary diagram and special graphic techniques were utilized to locate the critical point on the phase envelope. This work presents a computerized curve fitting method to generate the phase envelope from a given set of phase equilibrium data and then use the tie-line slopes to position the critical point. Experimental data are included and show excellent agreement with this new method.

British Library Electronic Table of Contents (United Kingdom)

Abstract:- Brine solution injection of beef contaminated with-Escherichia coli-O157:H7 on its surface may lead to internalization of pathogen cells and/or cross-contamination of the brine, which when recirculated, may serve as a source of new product contamination. This study evaluated survival of-E. coli-O157:H7 in brines formulated without or with antimicrobials. The brines were formulated in sterile distilled water (simulating the composition of freshly prepared brines) or in a nonsterile 3% meat homogenate (simulating the composition of recirculating brines) at concentrations used to moisture-enhance meat to 110% of initial weight, as follows: sodium chloride (NaCl, 5.5%) + sodium tripolyphosphate (STP, 2.75%), NaCl + sodium pyrophosphate (2.75%), or NaCl + STP combined with potassium ...

Energy Technology Data Exchange (ETDEWEB)

Source Philippe (on the island of La Govave, near Haiti) is described in terms of climatic, sociological, agricultural and technical background. Because of drought conditions, it became necessary to develop a solar still to provide the town with sufficient fresh water. The still, which has been in operation since 1969, is described in some detail as is the construction process. Brackish and sea water are used to produce more than 1250 liters of fresh water each day. A windmill is used to pump the brackish water from a well to an elevated storage tank; it flows by gravity to solar still basins where it is vaporized, then condensed on a sloping glass surface and collected. Benefits of the solar still to the town's economy and health are discussed. Cost of the project was $17,000. 10 references. (MJJ)

British Library Electronic Table of Contents (United Kingdom)

Objective.The objective of this study was to use the newly synthesized poly(quaternary ammonium salt) (PQAS)-containing polyacid to formulate the light-curable glass-ionomer cements and study the effect of the PQAS on the compressive strength and antibacterial activity of the formed cements.Materials and methods.The functional QAS and their constructed PQAS were synthesized, characterized and formulated into the experimental high-strength cements. Compressive strength (CS) and Streptococcus mutans viability were used to evaluate the mechanical strength and antibacterial activity of the cements. Fuji II LC cement was used as control. The specimens were conditioned in distilled water at 37 degrees C for 24 h prior to testing. The effects of the substitute chain length, loading as well as gra...

Energy Technology Data Exchange (ETDEWEB)

Tests on the scrubbing column have led to the following results: Use of a scrubbing column with Raschig rings is only meaningful for the sedimentation of particles exceeding diameters of 0.5 ..mu..m; drops of diameter size 1.5 ..mu..m are formed in the column; more efficient drop precipitators in the column air flow ease the load on subsequent suspended material filters thereby contributing to a longer life of these filters even at higher sodium ion concentrations in the washing water; with distillate of an 8% rather than 0.8% salt solution a decontamination factor greater than 10 can be calculated since larger particles precipitate more readily. This only applies, however, under the condition that the washing water is renewed regularly, if necessary daily where higher aerosol concentrations are present. If not, the decontamination factor will be reduced through the salt-containing secondary aerosols from the washing water.

British Library Electronic Table of Contents (United Kingdom)

Natural rubber (NR) and its derivatives as renewable and biodegradable materials have attracted considerable attention because of the serious pollution problems caused by synthetic materials and a shortage of resources. A new semi-interpenetrating polymer network (semi-IPN) based on epoxidised natural rubber and polyvinyl alcohol containing maleic acid as a crosslinking reagent was synthesized and characterized by FTIR, XRD, SEM, swelling ratio in both distilled water and toluene, and mechanical properties. The curing time and dose of maleic acid were varied from 10 to 60min, and from 10 to 60% (w/w), respectively. An IR spectroscopic study indicated the presence of an ester linkage at 1730cm-1 in maleic acid crosslinked with PVA in semi-IPN films. In addition, the crystalline content of P...

Energy Technology Data Exchange (ETDEWEB)

An experimental and theoretical study of heat and mass transfer analogy and a comparison of that to a binary liquid mixture evaporation is presented. Common organic solvents, ethanol and n-heptane, were used to form an alcohol - hydrocarbon mixture. Studies were carried out in a horizontal rectangular channel having air flow velocities of 0.2 - 0.9 m/s. Heat transfer coefficients were measured with a copper plate resistor and mass transfer coefficients with a square pool. The heat and mass transfer analogy is presented for a system having two evaporating compounds with a fixed value of air flow and verified by measuring and comparing mass transfer coefficients for distilled water with air flow velocities of 0.2 - 0.9 m/s. An illustrative example of the use of the theory for industrial ventilation is presented. (author)

International Nuclear Information System (INIS)

To sophisticate the nuclear fuel recycling processes, the transfer percentages for Pd, Mo, Te, and Sb should be determined. Each element solution containing NaNO_3 or HNO_3 was fed consistently into the thin film evaporator regulated in vac and at 50 deg C. The analyte percentages in the inside of the lid, in the condenser, and in the distillate were 10"-"1%/m"2, 10"-"3%/m"2, and 10"-"3% (DF = 10"5), respectively. The Mo percentage in the condenser was lower by a factor of 10 than those of other elements investigated. The NO_3"- percentages were nearly constant despite increasing HNO_3 concentrations, however, the ratios decreased with increasing NaNO_3 concentrations. (author)

Energy Technology Data Exchange (ETDEWEB)

A formulation to pelletize simulated high-level ICPP alumina waste calcine was developed. The pellets are formed on a 41-cm-diameter disc pelletizer using 5% bentonite, 2% metakaolin, and 5 wt % calcium hydroxide as a solid binder and a solution of 7M phosphoric acid and 4M nitric acid as a liquid binder. After drying and heat treatment at 800/sup 0/C for 2 hours, the average crush strength of the pellets is 3.9 MPa and the pellets have a leach resistance of 10/sup -3/ g/cm/sup 2//day, based on Soxhlet leaching for 48 h at 95/sup 0/C with distilled water.

Energy Technology Data Exchange (ETDEWEB)

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

Energy Technology Data Exchange (ETDEWEB)

The performance of advanced ceramics under cavitation loading in distilled water was studied by using a laboratory test with vibration-induced cavitation following the pattern of the ASTM standard G32-92. The hardened and tempered martensitic steel 100Cr6 was used as a reference. The aim was to identify mechanisms and the effects of important microstructural parameters on damage of polished Al{sub 2}O{sub 3}, Al{sub 2}O{sub 3}-ZrO{sub 2}, ZrO{sub 2} and SiC ceramics. Results showed that surface damage of brittle ceramics was mainly dominated by intergranular fracture, followed by detachment of single grains or fragments of them. Both incubation time and erosion rate were affected by the amount of initial surface cavities, grain sizes and secondary phases at grain boundaries. (orig.)

CERN Document Server

Vehicular communication (VC) systems have recently drawn the attention of industry, authorities, and academia. A consensus on the need to secure VC systems and protect the privacy of their users led to concerted efforts to design security architectures. Interestingly, the results different project contributed thus far bear extensive similarities in terms of objectives and mechanisms. As a result, this appears to be an auspicious time for setting the corner-stone of trustworthy VC systems. Nonetheless, there is a considerable distance to cover till their deployment. This paper ponders on the road ahead. First, it presents a distillation of the state of the art, covering the perceived threat model, security requirements, and basic secure VC system components. Then, it dissects predominant assumptions and design choices and considers alternatives. Under the prism of what is necessary to render secure VC systems practical, and given possible non-technical influences, ...

Science.gov (United States)

The efficiency of basic, direct and reactive dye removal from water by narrow-leaved cattail (NLC) powder treated with distilled water (DW-NLC), 37% formaldehyde+0.2 N sulfuric acid (FH-NLC), or 0.1 N sodium hydroxide (NaOH-NLC) at various pH levels (3, 5, 7, and 9) was tested. Desorption of the adsorbed dyes was also investigated. The type of NLC treatment and pH of the dye solution had little effect on removal of basic dyes, and efficiencies ranged from 97% to 99% over the range of pH used. Over a wide range of pH levels, all types of treated cattail powder had negative charges and probably attracted the basic dyes possessing positive charges. Efficiency of removal by the three NLC treatments ranged from 37% to 42% for direct dyes and from 22% to 54% for direct dyes at pH 7. The pH of the dye solution had substantial effects on the efficiency of removal in direct and reactive dyes. Dye removal was highest at pH 3, with 99% for a direct dye (Sirius Red Violet RL) ...

International Nuclear Information System (INIS)

Full text: In heavy-water-moderated power reactors, tritium is primarily produced by neutron capture in deuterium nuclei in the moderator and coolant. For CANDU 6 reactors, the estimated steady-state values are #approx# 3 TBq#centre dot#kg"-"1 D_2O in the moderator and #approx# 74 GBq#centre dot#kg"-"1 D_2O in the coolant. Tritium removal is one option available to reactor operators for use in their heavy water and tritium management strategies. The WTRF is designed to remove tritium from tritiated heavy water in each of the four CANDU units at the Wolsung Site, to immobilize the tritium and to store it on site. The detritiation process is based on three steps: the first one (front-end) involves the transfer of tritium from heavy water to deuterium gas; the second one (enrichment) concentrates the tritium in a cryogenic distillation system to produce essentially pure D_2 and T_2 streams; and in the third step the tritium is packaged for long-term storage. The WTRF ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents a case study of site characterization and hydrocarbon contamination plume mapping/delineation in a gas processing plant in southern Mexico. The paper describes innovative and cost-effective use of passive (non-intrusive) and active (intrusive) techniques, including the use of compound-specific analytical methods for site characterization. The techniques used, on a demonstrative basis, include geophysical, geochemical, and borehole drilling. Geochemical techniques used to delineate the horizontal extent of hydrocarbon contamination at the site include soil gas surveys. The borehole drilling technique used to assess the vertical extent of contamination and confirm geophysical and geochemical data combines conventional hollow-stem auguring with direct push-probe using Geoprobe. Compound-specific analytical methods, such as hydrocarbon fingerprinting and a modified method for gasoline range organics, demonstrate the inherent merit and need for such analyses to properly ...

Energy Technology Data Exchange (ETDEWEB)

The present investigation deals with the fabrication of liquid petroleum gas (LPG) sensor based on semiconducting oxide SnO{sub 2}. The gas sensor elements have been prepared by conventional solid state route. Addition of noble metal sensitizer, palladium and grain growth inhibitor, aluminum silicate to the base material SnO{sub 2}, not only improved the sensitivity towards LPG but also the selectivity in the presence of CO and CH{sub 4} gases. Out of various sensor compositions, SnO{sub 2}:Al{sub 2}Si{sub 2}O{sub 7} (35 wt.%):Pd (1.5 wt.%) sintered at 800 C for 5 h has shown high sensitivity (0.97) towards LPG at an operating temperature of 350 C. Different characterization techniques have been employed, such as differential thermal analysis (DTA), surface area analyzer, X-ray diffraction (XRD), to study the formation of SnO{sub 2}, surface area and crystallite size, respectively. The results suggested the possibility of utilizing the sensor element for the ...

Energy Technology Data Exchange (ETDEWEB)

A large amount of industrial water is used for cooling the various process fluids in the petroleum purification factories as well as petroleum chemistry factories. Consequently, a lot of heat exchangers as the necessary constitutional instruments are made of carbon steel. Due to the most of the corrosions of the carbon steel occurring in such cooling water systems are pitting corrosions, the inhibition thereof is extremely important for the elongation of the life of the plants and the stable operation. In this paper, the influences of water quality fractions on pitting corrosion of carbon steel in cooling water circumstance are examined aiming at the fouling in the cooling water. The fouling in the cooling water does not only increase the amount of occurrence of pitting corrosion but also accelerates the progress of pitting corrosion enlarging the rust due to its deposition near the anode. Since only the inhibitor is not sufficient to inhibit ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this project was to identify needs for environmental research development and demonstration projects that have the potential to improve the performance of oil and gas exploration, drilling, and production technologies for maximum recovery of domestic petroleum resources under optimal environmental and economic conditions. To achieve this objective several areas of work were addressed. The first task was to compile as much related data as possible. This was achieved by literature searches of a number of petroleum-related data bases. After acquiring sufficient background on environmental and economical areas that should be expanded, experts who are knowledgeable in these areas were contacted to further define specific issues. More than 33 identified areas were submitted to an in-house panel at NIPER to assure that the final environmental research demonstration and development needs that were selected to be expanded were unbiased ...

Energy Technology Data Exchange (ETDEWEB)

An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age-hardening and moisture susceptibility was conducted. The ESO residue, having a viscosity of 23.9 Pa{sm_bullet}s at 60{degrees}C (140{degrees}F), was blended with three different petroleum-derived asphalts, AAD-1, AAK-1, and AAM-1, that are known to be very susceptible to oxidative aging. Rheological and infrared analyses of the unaged and aged asphalts and the blends were then conducted to evaluate oxidative age-hardening. In addition, the petroleum-derived asphalts and the blends were coated onto three different aggregates, Lithonia granite (RA), a low-absorption limestone (RD), and a silicious Gulf Coast gravel (RL), and compacted into briquets. Successive freeze-thaw cycling was then conducted to evaluate the moisture susceptibility of the prepared briquets. The abbreviations used above for the asphalts and the aggregates are part of the Strategic ...

Energy Technology Data Exchange (ETDEWEB)

The Canadian Association of Petroleum Producers (CAPP) represents about 170 crude oil and natural gas exploration, development and production companies in regulatory hearings and legal proceedings. Its principal role is to enhance the economic well-being and sustainability of the Canadian upstream petroleum industry. This presentation explores the role that information technology (IT) plays in knowledge and information management and how this role relates to meeting Canada`s target for greenhouse gas emissions reductions set by the Kyoto Protocol. Actions such as the Voluntary Challenge Registry (VCR) and emissions reductions trading are re-visited and the information requirements associated with these actions are highlighted. It is shown that among others, emissions databases between jurisdictions (provincial, national, international) have to be integrated, reduction claims must be tracked, verified and cross-referenced to eliminate double ...

Energy Technology Data Exchange (ETDEWEB)

The search for alternative fuels and new fuel resources is a top priority for Turkey, as is the case in the majority of countries throughout the world. The fuel policies pursued by governmental or civil authorities are of key importance in the success of alternative fuel use, especially for widespread and efficient use. Following the 1973 petroleum crisis, many users in Turkey, especially in transportation sector, searched for alternative fuels and forms of transportation. Gasoline engines were replaced with diesel engines between the mid-1970s and mid-1980s. In addition, natural gas was introduced to the Turkish market for heating in the early 1990s. Liquid petroleum gas was put into use in the mid-1990s, and bio-diesel was introduced into the market for transportation in 2003. However, after long periods of indifference governmental action, guidance and fuel policies were so weak that they did not make sense. Entrepreneurs and users ...

Energy Technology Data Exchange (ETDEWEB)

This document provides information and presents data on the energy situation in many regions of Canada. The first part deals with the petroleum and the bitumen shales of Alberta (reserves, exploitation and production, environmental impacts), the second part discusses with the hydroelectricity choice of Quebec and the 2004 crisis. The nuclear situation of Ontario is presented in the third part (nuclear park, programs, uranium reserves, research and development on Candu reactors), while the fourth part deals with the renewable energies (wind power and biomass). The canadian situation facing the Kyoto protocol is discussed in the last part. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

British Columbia is rich in resources of coal but is deficient in resources of liquid petroleum. The overall objective of the B.C. Research Coal Liquefaction Program is to provide sufficient technical data to identify and evaluate coal conversion opportunities in the province. In this first quarterly report, liquefaction test systems are discussed and results from the testing of equipment, procedures and analytical methods using coal samples from Sukunka (N.E. coal) and Hat Creek (central interior) are presented. The proposed program to be undertaken over the next four years is outlined.

Energy Technology Data Exchange (ETDEWEB)

The effects of automation and optimization on the day-to-day activities of oil field operators are sketched in this lead-in editorial comment on a series of articles designed to provide an overview of the revolution that computers have brought to the petroleum industry. The articles that follow detail the role of databases in tracking production information, new system architectures based on common integrated data repositories that provide corporation-wide access, the way video and single-site supervisory control and data acquisition are combined to control wellsite production, and a case study about the integrated processes introduced by Wascana Energy to automate its fields.

Energy Technology Data Exchange (ETDEWEB)

This paper presents a unique method, currently under evaluation, that can continuously track pipeline operation providing essentially instantaneous responses to leaks or ruptures without causing a pressure drop or energy loss. Using the highly linear characteristics of a very accurate and repeatable meter and then correlating it to a second identical unit, a dynamic leak detection system is planned that can be retrofitted on existing pipelines without a major construction effort nor destroying the integrity of the existing transmission line. Initial tests performed on a crude oil transmission line verified the equipment's performance and established that the repeatability limits are sufficient to continue development of the concept.

International Nuclear Information System (INIS)

This is the first report about a relevant and compiled information on the Mexican Energy Sector. It was realized in one volume by the University Energy Program of the National Autonomous University of Mexico and it comprises information for the period 1996-1997. In the chapter 1 there are presented the numbers of hydrocarbon reserves. Chapter 2 treats about production, events and its results. Likewise chapter 3 shows information about the typical Installations for petroleum, gas and electricity including through of the nuclear energy. In the chapter 4, named Energy Consumption, is presented a National energy balance for 1996 and, finally there are a sections about the prices, the rates and a glossary to facilitate its understanding. (Author)

Energy Technology Data Exchange (ETDEWEB)

Knowledge of ground subsidence behavior provides for better economic planning and execution of a mining exploitation, higher safety and optimum use of the resources without ruining the environment. In addition, when considering subsidence generated by petroleum exploitation, the monitored (measured) subsidence, combined with geological information and a suitable prediction model, can provide data on the expanse of the oil field and thus aid in the estimation of available resources. An integrated survey system for monitoring mining subsidence is described which has been developed as part of a research program in cooperation with the Canada Centre for Mineral and Energy Technology. (JMT)

Energy Technology Data Exchange (ETDEWEB)

The present volume provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD Countries. It covers the years 1970 to 1982 year by year and includes many revisions and additions to data previously published. The balances in the present volume are based on data published in OECD Energy Statistics 1971-1981 and OECD Energy Statistics 1981-1982. Tables for each OECD Country include production, import, export, consumption by the different industries, transportation, agriculture, residential sector of the different energies: solid fuels, petroleum, gas, nuclear power and hydroelectricity.

Energy Technology Data Exchange (ETDEWEB)

Petroleum resources are finite and, therefore, search for their alternative non-petroleum fuels for internal combustion engines is continuing all over the world. Moreover gases emitted by petroleum fuel driven vehicles have an adverse effect on the environment and human health. There is universal acceptance of the need to reduce such emissions. Towards this, scientists have proposed various solutions for diesel engines, one of which is the use of gaseous fuels as a supplement for liquid diesel fuel. These engines, which use conventional diesel fuel and gaseous fuel, are referred to as 'dual-fuel engines'. Natural gas and bio-derived gas appear more attractive alternative fuels for dual-fuel engines in view of their friendly environmental nature. In the gas-fumigated dual-fuel engine, the primary fuel is mixed outside the cylinder before it is inducted into the cylinder. A pilot quantity of liquid fuel is ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented under 38 symposia. Subjects included reinforced concrete, protective coatings and linings, cathodic/anodic protection, chemical cleaning of boilers, managing corrosion with plastics, water treatment, HRSG boiler tube failure analysis, corrosion in oil and gas production, corrosion in petroleum refining and gas, processing, pipelines and tanks, high temperature materials, chemical process industry, aerospace equipment, materials technology developments for incinerators and waste fuel-fired processors, materials and corrosion in fossil-fuels conversion and combustion, corrosion in nuclear systems, marine corrosion, building systems, corrosion mechanisms, corrosion inhibitors and corrosion monitoring and measurement.

International Nuclear Information System (INIS)

A synthesis of scientific knowledge about petroleum biodegradation linked to uranium mineralisation is firstly done. Then the genesis of Huemul Uranium ore deposit (Malargue Town, Mendoza Province) is discussed, where Uranium ore is linked only with one type of asphaltite (there are three other types) from an oil field close by. This asphaltite type would be an efficient natural geological barrier for Uranium migration and it could be linked to a particular kind of biodegradation. The authors think that the International Wonuc Conference would be a good opportunity to discuss a way for future investigations. (author)

Energy Technology Data Exchange (ETDEWEB)

The UFIP (French Petroleum Industry Association) studies concerning polluted sites and soils and their rehabilitation are presented: characterization of the admissible maximum fuel or gas oil content in the ground, the issue of time effects, and the risks it may induce for public health; study on the various pollutant impacts on the environment (underground waters, biotope...); approach to the development of a dynamical model describing these phenomena and their influence on man, in order to derive consistent and reasonable decontamination objectives

Energy Technology Data Exchange (ETDEWEB)

''S-220'' white oil is used currently to impregnate and fill high voltage cables for 110-500 kilovolts; it has high electrical characteristics and meets production and use standards. High pressure and cooling problems, however, require filling cables with lower viscosity oils, while insulation needs still demand high viscosity. The authors developed a new white oil similar to S-220 using a neutral oil made in producing sulfonate additives. The process involved vacuum distillation, low-temperature paraffination, sulfation with oleum, neutralizing with ammonium hydroxide and simultaneous extraction of sulfo-salts and contact purification. The lowest content of aromatic hydrocarbons was sought. Dielectric qualities varied with viscosity. Satisfactory thermooxidational capability was found at 50/sup 0/C with an oil of no less than 50 mm/sup 2//sec viscosity. The final white oil had no more than 2% aromatic hydrocarbons, thus assuring ...

Science.gov (United States)

This document demonstrates the commercial status of the process units to be used in the Tri-State Synfuels Project at Henderson, Kentucky. The basic design philosophy as established in October, 1979, was to use the commercial SASOL II/III plants as a basis. This was changed in January 1982 to a plant configuration to produce gasoline via a methanol and methanol to gasoline process. To accomplish this change the Synthol, Oil workup and Chemical Workup Units were eliminated and replaced by Methanol Synthesis and Methanol to Gasoline Units. Certain other changes to optimize the Lurgi liquids processing eliminated the Tar Distillation and Naphtha Hydrotreater Units which were replaced by the Partial Oxidation Unit. The coals to be gasified are moderately caking which necessitates the installation of stirring mechanism in the Lurgi Dry Bottom gasifier. This work is in the demonstration phase. Process licenses either have been obtained or must be obtained for a number of ...

Energy Technology Data Exchange (ETDEWEB)

The separation of bitumens (B) and natural asphalts using a dialysis (D) method is studied. A moderately vulcanized latex of natural rubber, which was subjected to extraction by cold n-hexane prior to use, was used as the material of the membrane for dialysis. With dialysis of bitumen samples dispersed in a small quantity of n-alkane in a Soxhlet apparatus three fractions were acquired: a dialyzate, an undialyzable fraction and asphaltenes (the residue). N-pentane, n-hexane and n-heptane were used as the solvents for dialysis. Samples of oxidized road bitumen, grade AOSI 85/25, bitumens from the process of propane deasphaltization, natural asphalts from Trinidad and Albania and A80 grade bitumens from the oil distillation process were isolated using the dialysis method. The reproducability of the output of the fractions with varying suspensions and productivity of the dialysis, the dependence of the output on the length of the dialysis, the dependence of the output ...

Energy Technology Data Exchange (ETDEWEB)

Composites based on pure gypsum and polyester-styrene resin have been prepared using various doses of gamma radiation. Some physical properties of the prepared composites and the influence of irradiation dose on it have been studied as: compression strength, hardness, thermal decomposition temperature in nitrogen or oxygen, and the change in weight in aqueous solutions with different pH values. The glass transition temperature of the pure polymer and the composites increases with increasing the irradiation dose up to a plateau, and the glass transition temperature of the pure polymer is lower than that of the composites. The irradiation dose does not seem to affect the decomposition temperature of the pure polymer or the composites significantly and the decomposition temperature in presence of nitrogen is higher than that in presence of oxygen. Increasing the irradiation dose leads to an enhancement of the compression strength of the pure polymer and the prepared composites; the ...

Energy Technology Data Exchange (ETDEWEB)

This invention relates with a pot-type catalyst carrier which excels as a catalyst carrier when such heavy oils as ordinary pressure distillation residue, oil sand oil, and shale oil are decomposed or treated by hydrogenation. The conventional pot-type carrier is produced by dropping a small drop of a slurry (containing a catalyst component) onto a particle bed and drying it. But the demerit is a large particle size and less catalyst activity or strength. In this invention, a mixture of such carrier components as allophane, red mud, bauxite and latellite, etc.. 60 - 80 weight parts. and a binder 20 - 40 weight parts is added with water to form a slurry of 10 - 30 weight% solid concentration. Slurry is wet-crushed to make the average particle size 0.6 - 2.0 micron, then spray-dried and burned to obtain a pot-type catalyst carrier with average particle size 30 - 200 micron and abrasion index below 10. This catalyst showed high yield of kerosene and light oil in the ...

Energy Technology Data Exchange (ETDEWEB)

The metal dependence of mesoporous activated carbons with various metal acetylacetonate (acac) particles prepared from Morwell coal was studied. In experiment, the mixture of Morwell coal and acac metal complexes were dissipated into tetrahydrofuran, and after agitation in Ar atmosphere, the solvent was removed by vacuum distillation. Coal specimens with Fe(acac)3, Ni(acac)2 and Co(acac)2 as acac complexes were activated by exchanging flow gas with water vapor after heat treatment in N2 gas flow at 900{degree}C. The pore sizes of the specimens were obtained from N2 adsorption isotherms by BET method and BJH method. Conditions of pores and metals in the specimens were examined by XRD measurement and TEM observation. The relation between the above conditions and pore characteristics obtained from adsorption experiment was also examined. As a result, the difference in mesopore ratio between the specimens and blank specimens was larger in the order of Fe, Co and Ni, ...

Energy Technology Data Exchange (ETDEWEB)

The coke plant at the Sparrows Point Plant consist of three coke oven batteries and two coal chemical plants. The by-product coke oven gas (COG) consists primarily of hydrogen, methane, carbon monoxide, nitrogen and contaminants consisting of tars, light oils (benzene, toluene, and xylene) hydrogen sulfide, ammonia, water vapor and other hydrocarbons. This raw coke oven gas needs to be cleaned of most of its contaminants before it can be used as a fuel at other operations at the Sparrows Point Plant. In response to environmental concerns, BSC decided to replace much of the existing coke oven gas treatment facilities in the two coal chemical Plants (A and B) with a group of technologies consisting of: Secondary Cooling of the Coke oven Gas; Hydrogen Sulfide Removal; Ammonia Removal; Deacification of Acid Gases Removed; Ammonia Distillation and Destruction; and, Sulfur Recovery. This combination of technologies will replace the existing ammonia removal system, the ...

Energy Technology Data Exchange (ETDEWEB)

The NiMo sulfide supported on Ketjen Black (KB) was more effective and yielded lighter oil products containing light fractions with their boiling point below 300{degree}C during the two stage liquefaction combining low temperature and high temperature hydrogenation the conventional NiMo/alumina catalyst and FeS2 catalyst. Although the NiMo/alumina yielded increased oil products during the two stage liquefaction, the lighter oil fractions did not increase and the heavier fractions increased mainly. This suggests that the hydrogenation of aromatic rings and successive cleavage of the rings are necessary for producing the light oil, which is derived from the sufficient hydrogenation of aromatic rings using catalysts. For the two stage reaction with NiMo/KB catalyst, it was considered that sufficient hydrogen was directly transferred to coal molecules at the first stage of the low temperature reaction, which promoted the solubilization of coal and the successive hydrogenation at the high ...

Energy Technology Data Exchange (ETDEWEB)

Biodiesel is derived from triacylglycerides and is produced primarily through transesterification, a chemical reaction of vegetable oils with alcohol, methanol or ethanol. The cost of raw material should be considered since 85 per cent of production cost is related to vegetable oil. The purpose of this study was to evaluate oil expression of sunflower seed. It also examined the sunflower crude oil as a raw material for biodiesel by transesterification in both laboratory and pilot scale studies. Three different biodiesel purification methods were examined. The best result for oil expelling (68.4 per cent) at the experimental stage was obtained for seeds with a moisture content of 6.9 per cent at 25 degrees C and at a screw speed of 114 rpm. For biodiesel production at the laboratory scale, the best result for oil expelling was 87.5 per cent. It was obtained with an ethanol:oil molar ratio of 4.7:1 and with a 4.42 per cent catalyst concentration related to the quantity of oil that had to ...

Energy Technology Data Exchange (ETDEWEB)

An evaporator using a hydrophobic membrane made from a polytetrafluoroethylene (PTFE) was developed to improve DF (Decontamination Factor) and to reduce evaporator size. The membrane distillation, provided by the evaporator, is a new technique for liquid purification. Fundamental experiments were carried out to develop the membrane filter (tube type, outer diameter, 8 mm; membrane thickness, 500 {mu}m) for radioactive liquid treatment. The continuous operation test using actual liquid waste was also made during about 3,000 h. (This is almost equal to the operation time of an actual evaporator per year.) The evaporation rate decreased with increase an operation time due to contamination of waste impurity. But the rate was recovered by washing the membrane with hot water and then drying it. DF was over 10{sup 4} which is ten times larger than that for a conventional system. A pilot plant (capacity, 200 kg-liquid waste/h) was constructed and its performance test was ...

International Nuclear Information System (INIS)

An ampoule corrosion tests technique is presented for making a comparative corrosion-proof estimation of austenitic steels and alloys which are candidate materials for the ITER first wall and shield blanket. Influence of Cl"- on the rate and character of corrosion cracking has been determined. The dependence of time before destruction on Cl"- contents was obtained by experiments in twice-distilled water at a Cl"- content value of less than 0.05 mg/l. Kinetics of a corrosion crack growth has been determined by way of acoustic emission and measurement of electrical resistance. It has been revealed, that corrosion cracking of 316L and 316Ti steels in water with 100 mg/l of Cl"- takes place at temperatures over 50 C. For 316L (Russian analogue), 316Ti, 08Cr18Ni10Ti (type 304), 00Cr16Ni15Mo3Nb (type 316) steels and CrNiMo-1 (42-47%Cr, 1%Mo, Ni-base) alloy corrosion long-term strength and crack-resistance characteristics were obtained. Results of tests show, that ...

Energy Technology Data Exchange (ETDEWEB)

This paper described the basic design of Alpha Aqueous Waste Treatment Process in NUCEF. Since various experiments using the TRU (transuranium) elements are carried out in NUCEF, wastes containing TRU elements arise. The liquid wastes in NUCEF are categorized into three types. Decontamination and volume reduction of the liquid waste mainly of recovery water from acid recovery process which has lowest radioactive concentration is the most important task, because the arising rate of the waste is large. The major function of the Alpha Aqueous Waste Treatment Process is to decontaminate the radioactive concentration below the level which is allowed to discharge into sea. Prior the process design of this facility, the followings are evaluated:property and arising rate of the liquid waste, room space to install and licensing condition. Considering varieties of liquid wastes and their large volume, the very high decontamination factor was proposed by a process of multiple evaporation ...

Science.gov (United States)

The objectives of this project are to support the DOE direct coal liquefaction process development program and to improve the useful application of analytical chemistry to direct coal liquefaction process development. Independent analyses by well-established methods will be obtained of samples produced in direct coal liquefaction processes under evaluation by DOE. Additionally, analytical instruments and techniques which are currently underutilized for the purpose of examining coal-derived samples will be evaluated. The data obtained from this study will be used to help guide current process development and to develop an improved data base on coal and coal liquids properties. A sample bank will be established and maintained for use in this project and will be available for use by other researchers. The reactivity of the non-distillable resids toward hydrocracking at liquefaction conditions (i.e., resid reactivity) will be examined. From the literature and data ...

Energy Technology Data Exchange (ETDEWEB)

The colloquium began with a talk of Michel Destot about the energy policy in France, in comparison with the economic situation, the social solidarity and the durable development. The paper presents then the report of the three round tables conferences, in discussion form, giving the point of view of each participant. The discussed subjects are the new needs and offers of the France after the storm and the petroleum crisis, the Europe and the gas, the Europe and the electric power. (A.L.B.)

Energy Technology Data Exchange (ETDEWEB)

Shale oil as a fuel source would need to compete with crude oil. The prospects for shale oil therefore depend upon the market outlook and likely prices for crude oil and its products. These are examined for both the world and Australia. For Australia, market prospects for shale oil are assessed in terms of maintaining a degree of self-sufficiency in petroleum fuels. Shale oil might also need to compete with other synthetic liquid fuels. The prospects for producing these in Australia are discussed. Some factors which might influence the pattern of development of a synthetic fuels industry in Australia are described and a role suggested for the federal government to ensure optimum development for national economic growth. 6 refs., 1 fig.

British Library Electronic Table of Contents (United Kingdom)

ABSTRACT Shallow-lacustrine delta deposits of the Upper Triassic Yanchang Formation form the most important petroleum reservoir sandstone units in the Ordos Basin, China. Recent hydrocarbon exploration and outcrop studies demonstrated that shallow-lacustrine sand-rich deltas developed extensively along the gentle flanks and central part of the basin. The vertical succession of facies indicates that the Yanchang Formation records the entire lacustrine life cycle of the Late Triassic Ordos Basin. Four third-order transgressive-regressive cycles and two larger shallow-lacustrine deltaic cycles have been recognized. A process-based depositional model, derived in part from the modern Ganjiang delta in Poyang Lake, China, is used to infer the origins of the sand-rich lacustrine delta deposits. S...

International Nuclear Information System (INIS)

Lebanon has imported in 1996 5000 Kt of carburants causing about 80 Kt of SO_x; 40 Kt of NO_x; 3 Kt of dusts and 3.5 million tons of CO_2. The atmospheric pollution in Lebanon is due to three main sources: - Thermal central of electric production - Industries (cement) - Transportation sector The document describes in tables: the inventory of pollutants and pollutant emissions in 1993 and 2010; industrial and heating gas oil; liquified petroleum gas commercial propane; fuel oil for EDL; consumption of energy in 1996; sectorial distribution of pollutants PPM; emissions of CO_2 per tons per habitant in 1993; consumption in 1993 broken down by use and application. Finally, three projects concerning public transportation were presented

Energy Technology Data Exchange (ETDEWEB)

Oil shales of the US represent a tremendous store of potential oil. Most of the deposits are relatively unknown and warrant additional investigation. The summary presented cannot hope to cover all of the deposits. Information about them is usually available only locally. However, the 3 best known deposits - the Green River formation, the Devonian black shales, and the retort member of the Phosphoria formation - represent well over 2 trillion bbl (300 x 10/sup 12/ ton) of potential oil in place. This is an oil resource large enough to supplement quite adequately the US petroleum supply, to extend the time available for realigning our energy supply mixes, and to help reach a satisfactory solution to our current energy dilemma. The concentrated resource in the Green River formation is obviously the next most feasible source of oil. If it cannot be developed, all the other deposits will have to wait until it can be. 100 references.

Energy Technology Data Exchange (ETDEWEB)

The objective of this study was to provide a framework for land use and resource allocation decisions in the Northeast Coal Block of British Columbia. The area was divided into a number of sites, and information gathered in two main areas, 1) status of the resource base, and 2) resource management/planning/development. A map and physical description of each site is provided as well as such information as - air quality, soils, vegetation, water resources, petroleum and natural gas resources, coal resources, and gravel resources, agricultural resources, timber resources, fisheries and wildlife resources, recreatational and aesthetic (visual) resources. The appendix volume provides a summary of the institutional management framework and approval procedures for all significant resource sectors. Provincial legislation and government acts are identified.

British Library Electronic Table of Contents (United Kingdom)

Remote, offshore gas reserves have long been a challenging deepwater petroleum resource to tap. Natural gas in many offshore regions is plentiful, but lacks access to the market because of the logistical challenges and costs. Most large offshore gas discoveries are capped, and gas associated with oil production is re-injected into the reservoir or is flared. A more attractive option is to convert the gas into a liquid product on a floating production, storage, and offloading (FPSO) vessel. However, some conventional process technologies are not well suited for operation on floating vessels that are highly space and weight constrained and may challenge vessel stability during inclement weather. Microchannel process technology units under development offer intensified processes that are suit...

Energy Technology Data Exchange (ETDEWEB)

Malaysia's petroleum industry is looking forward to an expansionary period until the end of the century, with the role of gas being greatly enhanced. The state oil firm Petronas sees increasing oil and gas reserves, making fuller use of abundant gas reserves, an exploration thrust into deepwater areas and the intensification of environmental protection as some of the points of emphasis in its current programme. The state firm president Tan Sri Datuk Azizan Zainul Abidin says that in the past few years a national economic growth rate of 8 percent has resulted in rising energy demand. Economic growth is projected to continue, so that an increase in power demand can be expected for the next few years. 'Fortunately, we are experiencing the same bullish trend in oil exploration and development,' he says. (author)

Science.gov (United States)

Hydrogenation residue is the product left over when petroleum residue feedstocks (or coal) are treated by, e.g. the Veba Combi Cracking (VCC) process. Many tests in semitechnical and full-sized coke ovens were carried out with hydrogenation residue (HR) as an additive in coking coal blends for the production of blast furnace coke or foundry coke. The results of the investigations reported in this paper demonstrate that HR is a very promising alternative for enlarging the coking coal basis compared to other processes or the use of other additives. The application of HR on an industrial scale did not indicate any negative impact on the handling of the hydrogenation residue or on the operation of the coke oven battery.

British Library Electronic Table of Contents (United Kingdom)

Well over 90 percent of all motorized transportation is fueled by products of petroleum, but the end of such widespread use of oil may be in sight. Among alternative fuels for land transportation, electricity appears to be the most promising, in part because it can be renewably produced and readily transmitted. The inadequacy and high cost of on-board storage of electrical energy present major challenges to widespread deployment of electric traction, and may do so for many years. On-board generation of electrical energy also presents challenges. The third means of powering electric traction is to provide for connection to the electricity grid while in motion. Grid-connected vehicles (GCVs) are an established feature of many cities and of much inter-city transportation, chiefly as electric ...

British Library Electronic Table of Contents (United Kingdom)

Three alternative extraction procedures were carried out in order to separate the antioxidant components and isolate an efficient extract from Origanum dictamnus. Procedure A included sequential extractions with petroleum ether (PE), diethyl ether (DE) and ethanol; procedure B sequential extractions with PE and ethyl acetate (EAc); procedure C a single step extraction with ethanol. The most efficient radical scavengers, according to the DPPH method, were isolated in ethanol extract of procedure A (mainly rosmarinic acid), followed by ethanol extract of procedure C. However, both ethanol extracts had low solubility in oil and could not protect it. EAc and DE extracts, containing mainly apigenin and epirosmanol ethyl ether, presented lower radical scavenging activity but were very effective ...

Energy Technology Data Exchange (ETDEWEB)

Recent developments in rechargeable Li-ion battery technology include the use of lithium-carbon compounds instead of metallic anodes. Non-graphitizable carbons offer high capacity as the anode material but it's large irreversible capacity must be solved. The ultimate goals of the present work are to understand the origin of the high capacity and large irreversible capacity in conjunction with the structural change due to Li intercalation and thus to establish a scientific basis for optimizing their performance in real batteries. 'House of cards' model is considered and emphasis is given to find out the size of the pores present in the carbon fibers prepared from an isotropic petroleum pitch and heat treated at 1200degC. Small angle neutron scattering and wide angle neutron scattering results provide enlargement of pores and d-spacing of grapheme layers after Li intercalation. (author)

British Library Electronic Table of Contents (United Kingdom)

Within the current outlook for sustainable electric energy supply with concomitant reduction in emission of greenhouse gases, accelerated attention is focusing on the long-term development of hydrogen fuel cell and all-electric battery vehicles to provide alternative fuels to replace petroleum-derived fuels for automotive national fleets. The potential varies significantly between large industrially developed nations and smaller industrially developing nations. The requirement for additional electric energy supply from low-specific energy renewable resources and high-specific energy nuclear resources depends strongly on individual national economic, environmental, and political factors. Analysis of the additional electric energy supply required for the two potential large-scale technologie...

British Library Electronic Table of Contents (United Kingdom)

Guar seed gum, consisting primarily of a high molecular weight galactomannan, is the most cost effective natural thickener, having broad applications in the food, cosmetics, paper, pharmaceutical and petroleum industries. The properties of the polymer can potentially be enhanced by genetic modification. Development of suitable endosperm-specific promoters for use in guar is desirable for metabolic engineering of the seed gum. A ~1.6?kb guar mannan synthase (MS) promoter region has been isolated. The MS promoter sequence was fused with the GUS reporter gene and overexpressed in the heterologous species alfalfa (Medicago sativa). The potential strength and specificity of the MS promoter was compared with those of the constitutive 35S promoter and the seed specific ?-phaseolin promoter. Quant...

CERN Document Server

Heterogeneous anisotropic diffusion problems arise in the various areas of science and engineering including plasma physics, petroleum engineering, and image processing. Standard numerical methods can produce spurious oscillations when they are used to solve those problems. A common approach to avoid this difficulty is to design a proper numerical scheme and/or a proper mesh so that the numerical solution validates the discrete counterpart (DMP) of the maximum principle satisfied by the continuous solution. A well known mesh condition for the DMP satisfaction by the linear finite element solution of isotropic diffusion problems is the non-obtuse angle condition that requires the dihedral angles of mesh elements to be non-obtuse. In this paper, a generalization of the condition, the so-called anisotropic non-obtuse angle condition, is developed for the finite element solution of heterogeneous anisotropic diffusion problems. The new condition is essentially the same ...

Energy Technology Data Exchange (ETDEWEB)

Twenty-eight measurement while drilling tools are listed in this year's MWD Comparison Tables. Updated data on tools listed last year and data on five new tools provide a convenient guide for choosing MWD systems. Future MWD technologies include sonic tools and tools that make measurements ahead of the bit. For the seventh year, Petroleum Engineer International presents the Measurement While Drilling (MWD) Tables comparing a variety of available tools from many different vendors. The 1994 Tables include two additional companies and five new MWD tools not found in last year's Tables. However, the tables should serve only as a reference source. System specifications can change rapidly as tools are refined and new technologies develop. Operators and contractors should consult designated MWD marketing representatives before making a final tool selection.

International Nuclear Information System (INIS)

The role of the Latin American state oil companies (LASOCs) in establishing national industries to fuel economic development is discussed. LASOCs are represented internationally in an organization called ARPEL (Asistencia Reciproca Petrolera Estatal Latinoamericana) which is aimed to foster interchange, cooperation, and mutual assistance among its 20 member companies, as well as to promote economic integration of Latin America through its petroleum sector. State oil companies in Latin America date from 1922, when the oldest LASOC was created in Argentina. LASOCs are responsible for ca 80% of petroleum activities in Latin America. As of 1990, Latin American oil reserves, including gas liquids, amounted to ca 122 billion bbl or 12.2% of the world total. Regional oil production averaged 7.4 million bbl/d in 1990. Refining capacity is ca 7.7 million bbl/d, of which 80% is operated directly by LASOCs. Natural gas reserves are 7.3 trillion m"3, ca 6% ...

Science.gov (United States)

The strategy for building SASOL plants reflects a commitment to long-range planning. The first plant, which represented a large investment for a moderate production capacity, was built to establish a technology for reducing South Africa's dependence on imported motor fuels. After the success of the plant, SASOL made plans for a larger plant, which had to be justified solely on economic grounds. At that time, petroleum crude was cheap and plentiful, and the second plant was cancelled. But when OPEC formed and the price of petroleum crude was increased, the South African government reconsidered the plans for another SASOL plant. Furthermore, because the cost of fuels produced at Sasol I proved to be significantly insensitive to inflation and future OPEC price increases were expected, SASOL projected that a new, larger plant should make a profit within a few years after its initial operation. But OPEC prices and inflation have risen even ...

Energy Technology Data Exchange (ETDEWEB)

The Cambro-Ordovician platform was formed along the margin of the old super-continent of Laurentia approximately 470 million years ago, and is a prolific producer of hydrocarbons. This presentation provided a geological review of the region as well as estimates of the amounts of oil in place. A simplified geological cross-section of the formation was presented, as well as a chart of the Anticosti Basin of western Newfoundland. Details of exploration wells targeting the Cambro-Ordovician carbonate platform and current west coast land holdings were provided. An outline of the area's petroleum system included details of source rock, reservoirs, traps and seals and migration and timing. Offshore prospects for the platform were estimated to be in the region of 100 to 200 million barrels. Onshore prospects were estimated to be in the region of 30 million to 150 million barrels. It was noted that limited coverage by onshore seismic data may mean that larger ...

Energy Technology Data Exchange (ETDEWEB)

In world crude oil markets, 1987 was a year of limited recovery and relative stability after the dramatic price slide of early 1986. Both foreign and domestic crude thereafter, ending the year somewhat higher than a year ago. In contrast, product wholesale markets remained relatively stable throughout the year, while retail prices sustained a fairly steady increase. As has been the case for over a decade, major price movements in international oil markets generally reflected responses to actual or perceived changes in the policies of the Organization of Petroleum Exporting Countries (OPEC) and/or its members. The year began with prices on an upward trend, in reaction to the December 1986 OPEC meeting in which the members resolved to return to an official pricing structure (a departure from the market-based pricing of 1986), and to reduce output quotas. Prices continued to rise until August, when evidence of continued OPEC overproduction appeared to outweigh market ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the development, design, and fabrication of the crude oil process facilities, and the conversion of an existing tanker for use at the Liuhua 11-1 Field. Over a 16-month period spanning 1994 and 1995, Amoco Orient Petroleum Company, and partners, China Offshore Oil Nanhai East Corporation (CONHE), and Kerr-McGee China Petroleum Ltd., converted a crude oil tanker originally built in 1975 to the Nanhai Sheng Li, the floating production, storage and offloading (FPSO) facility for the Liuhua 11-1 Field. The FPSO will process up to 65,000 BOPD produced from 20 subsea wells located 1.7 miles away. In addition to the processing facilities for produced oil and water, the FPSO has a processed crude oil storage capacity of 715,000 bbls. The ship`s propulsion system was removed during the conversion, because the FPSO is permanently moored at site by means of a 10-point, ``soft`` mooring. The mooring system was designed to survive the ...

Energy Technology Data Exchange (ETDEWEB)

The Hyperion project was developed to determine an algorithm for assessing the risk of hydrate plug formation in the pipeline transport oil-water-gas mixtures at low temperatures. The project is a collaboration between physicists, chemists and engineers within the petroleum industry. This paper provided an overview of the project and outlined results obtained as the project entered its third and final year. The main objective of the project has been to understand the inherent mitigation effects of some oils on gas hydrate formation as well as to develop methods of predicting the risk of hydrate plugging. To date, the project has extracted and studied natural inhibiting components (NICs) in oils. Molecular modelling techniques have been used to study hydrate and fluid interfaces in order to estimate the driving force of agglomeration and growth through mechanical surface stress and measurement of surface wave fluctuations. A scheme is also being developed measure ...

Energy Technology Data Exchange (ETDEWEB)

The decision of a firm to make investments on petroleum fields depends on the expected economic performance and on the firm economics context and on country economic and regulatory constraints. Traditionally, the Net Present Value (NPV) has being used for decision criterion as a measure of profitability of investments. The other indicators are used to help investment decision, because, according to the priorities established by the firm, only one indicator may not be sufficient. On this paper we will show production strategies considering a set of economic indicators: NPV, actualized Np, Return on investment (ROI), Equivalent Present Value (EPV), Cost Benefit, and NPV/Np ratio. The use of different economic indicators permits capture different aspects from in a decision process, i.e., each indicator or a set of economic measures may result in a different perspective, that will influence the decision manager. It is important to emphasize the use of more than one ...

Energy Technology Data Exchange (ETDEWEB)

There are over 4,500 petroleum platforms in the north-central Gulf of Mexico. Explosives are commonly used to remove platforms and have the potential to kill nearby sea turtles. From June 1988-June 1990, the authors used aerial surveys to study turtle density and the spatial relationship between turtles and platforms offshore of Louisiana. They sighted 316 turtles most of which (92%) were loggerheads. Seventy-eight percent were sighted just east of the Mississippi River offshore of the Chandeleur Islands. East of the river, turtle densities ranged from 0.92 (winter) to 4.83 turtles/100 sq km (spring). West of the river, annual densities ranged from 0.11-0.50 turtles/100 sq km. East of the river, three statistical tests indicated that turtles were generally closer to platforms than expected by chance alone. West of the river, turtles were randomly located with respect to platform locations. Before explosives are used, current mitigation measures require that no ...

Science.gov (United States)

This report presents the operating results for Run 244 at the Advanced Coal Liquefaction R and D Facility in Wilsonville, Alabama. This run was made in an all-distillate Integrated Two-Stage Liquefaction (ITSL) mode using Illinois 6 coal from the Burning Star mine. The primary objective was to demonstrate the effects of temperature programming an aged catalyst batch on the ITSL product slate, especially on the net C/sub 1/-C/sub 5/ gas production and hydrogen consumption. Other objectives were to demonstrate the effect of fresh catalyst addition and to age the catalyst batch for an extended run with catalyst addition and withdrawal. Run 244 began on 4 July 1983 and continued through 27 September 1983. During this period, 182.9 tons of coal was fed in 1872 hours of operation. Seven special product workup material balances and two hydrotreater balances were defined, and the results are presented herein. From 27 to 30 September, 7.4 tons of Wyodak (Clovis Point mine) ...

International Nuclear Information System (INIS)

On the basis of environmental considerations, a high temperature gas cooled reactor (HTGR) was proposed as the heat source for the Natuna project for CO_2 conversion. To convert CO_2 to useful products, a large amount of high quality water is required for the chemical processes, boilers and other purposes. One LNG production train (maximum of six trains) would produce 0.4 x 10"9 SCF/d of saleable gas and 1.4 x 10"9 SCF/d of CO_2 (in the case of the Exxon process). This CO_2 gas would then be converted to automobile fuel (methane, methanol), which requires a large amount of water. Natural gas from an off- shore gas field is piped to the petrochemical complex on Natuna Island (about 228 km). Natuna is a small island that, apart from sea water, does not have much available water. The desalination process is considered to be the only solution to the water demand problems of the petrochemical complex. A nuclear desalination system was designed to provide high quality water for this complex. ...

Energy Technology Data Exchange (ETDEWEB)

Recent efforts to identify methods of modeling pitting corrosion damage of high-level radioactive-waste containers are described. The need to develop models that can provide information useful to higher level system performance assessment models is emphasized, and examples of how this could be accomplished are described. Work to date has focused upon physically-based phenomenological stochastic models of pit initiation and growth. These models may provide a way to distill information from mechanistic theories in a way that provides the necessary information to the less detailed performance assessment models. Monte Carlo implementations of the stochastic theory have resulted in simulations that are, at least qualitatively, consistent with a wide variety of experimental data. The effects of environment on pitting corrosion have been included in the model using a set of simple phenomenological equations relating the parameters of the stochastic model to key ...

Energy Technology Data Exchange (ETDEWEB)

The diminishing clean oil reserve is driving the search for new or improved ways to reduce the level of NSO-containing species found in high abundance in heavy crude oils. Hydrotreatment is the currently preferred technique to remove those polar species. Unfortunately, nitrogen-containing compounds cause coke formation on the surface of the hydrotreatment catalyst, leading to partial or complete deactivation. Here, positive- and negative-ion electrospray ionization Fourier transform ion cyclotron resonance mass spectrometry (ESI FT-ICR MS) identify those nitrogen compounds that resist hydrotreatment. ESI preferentially ionizes polar (e.g., heteroatom-containing) species: basic molecules are detected as positive ions and acidic/neutral molecules as negative ions. FT-ICR MS resolves thousands of species in a single mass spectrum, allowing for unambiguous determination of elemental composition, C{sub c}H{sub h}N{sub n}O{sub o}S{sub s}, for identification of compound ...

Science.gov (United States)

To determine the effects of ammonium chloride (NH4Cl) dosage and swimming exercise training during 4 weeks on bone metabolic turnover in rats, seven-week-old female 24 Wister-Kyoto (WKY) rats were investigated by bone status including bone mineral density (BMD) and biomechanical markers from blood and urine. Twenty-four rats (initial weight: 191.2+/-7.6 g) were randomly divided into four groups: baseline (8 weeks old) control group (n=6, BC), 4-week control group (n=6, Con), 4-week swimming exercise loading group (n=6, Swim) and 4-week chronic NH4Cl dosage group (n=6, Acid). All rats were fed an AIN93M diet (Ca: 0.5%, P: 0.3%), and both Con and Swim groups were pair-fed by feeding volume of the NH4Cl dosage group. The acid group only received 0.25 M NH4Cl distilled water ad libitum. At the end of the experimental period, rats were sacrificed with blood drawn and femur and tibia were removed for analysis of bone mineral density (BMD) by dual energy X-ray ...

International Nuclear Information System (INIS)

In light of the recent rapid increase in the fossil fuel prices it is meaningful to evaluate the impact of these price changes in the economics of dual-purpose desalination projects producing electricity and fresh water simultaneously. The price of crude oil and LNG (Liquefied Natural Gas) has increased by about 200% and 100% during the past three or four years. The uranium price has also increased by nearly 500% during the same period. The purpose of this paper is to analyze and compare the economics of SMART (System-integrated Modular Advanced ReacTor) which is being developed as a small size PWR type and the LNG Combine Cycle coupled with MED (Multi-Effect Distillation) which are being acknowledged as promising energy sources for the future in Korea. The methods of analysis used in this paper are the lifetime leveled cost method for the power and water cost calculation and the power credit method for the total cost allocation. DEEP (Devaluation Economic ...

International Nuclear Information System (INIS)

The subject of quantum optics has undergone considerable development in the last twenty-five years. Spurred by the invention of the laser, the theoretical understanding of the coherence and statistical properties of optical beams has now attained a stage of maturity where it is possible to treat different kinds of light sources. Over approximately the latter half of this period of development in quantum optics, the free-electron laser (FEL) has been developed to the point where it is now regarded as a tunable light source of considerable versatility, with prospects of producing radiation over a wide range of wavelengths at large levels of power. Since the basic mechanism for radiation gain in an FEL can be understood in classical terms, much of the literature on the subject does not need to venture outside the domain of classical physics. However, it is natural that the coherence and statistical properties of photon beams produced by FEL's should be investigated as they are in ...

Science.gov (United States)

The overall objective of this project was to develop a new approach for the direct liquefaction of coal to produce an all-distillate product slate at a sizable cost reduction over current technology. The approach integrated coal selection, pretreatment, coal swelling with catalyst impregnation, liquefaction, product recovery with characterization, alternate bottoms processing, and a technical assessment including an economic evaluation. Heterofunctional solvents were the most effective in swelling coals. Also solvent blends such as isopropanol/water were more effective than pure solvents alone. Impregnating slurry catalysts simultaneously during coal swelling showed that better uptake was achieved with nonswelling solvent and higher impregnation temperature. Some enhancement in initial coal conversion was seen liquefying SO{sub 2}-treated Black Thunder coal with slurry catalysts, and also when hydrogen donor liquefaction solvents were used. Noncatalytic reactions ...

Energy Technology Data Exchange (ETDEWEB)

In January 2001, Husky Oil Operations Limited (Husky), in joint-venture with Petro-Canada submitted a Development Application (DA) to the Canada-Newfoundland and Labrador Offshore Petroleum Board (C-NLOPB) for the White Rose Development. This DA was prepared following the Canada-Newfoundland Atlantic Accord Implementation Act and the Canada-Newfoundland and Labrador Atlantic Accord Implementation Newfoundland and Labrador Act. In December 2001, the C-NLOPB approved the White Rose DA. This document outlined a proposed amendment to the original Development Plan involving an expansion of its White Rose Development in the Jeanne d'Arc Basin on the Grand Bank. The expansion will consist of a subsea tie-back to the Floating Production, Storage and Offloading (FPSO) vessel through the existing Southern Glory Hole (SGH) and utilizing a new glory hole constructed approximately 4 km south of the SGH. The document presented an overview of the development; geology, ...

Energy Technology Data Exchange (ETDEWEB)

The 3-D model program was developed to apply a mise-a-la-masse method to linear current sources with optional shapes. Mise-a-la-masse method is a bipolar mapping survey method using current sources installed in wells, and recently has been widely used for direct exploration of geothermal reservoirs. This method is also used for monitoring underground fluid as electrode arrangement of fluid flow tomography for surveying underground fluid (geothermal fluid, underground water, petroleum). In the geothermal reservoir exploration, the casing pipes of wells are used as linear current sources, and measured data are processed as those based on vertical current source. In the largely inclined well, the inclination of current sources should be considered. The 3-D modeling program was developed by difference calculus using the theoretical potential equation and apparent resistivity based on linear current sources with optional 3-D shapes. The numerical model experiment result ...

Energy Technology Data Exchange (ETDEWEB)

The deep water parts of the Moere and Southern Voering Basins are large frontier areas, which are considered to contain significant undiscovered hydrocarbon resources, within Cretaceous and Paleogene reservoirs. PGS Reservoir AS have evaluated the Cretaceous and Paleogene successions of the shallow and deep water areas offshore Mid-Norway using high-resolution sequence stratigraphic techniques. The successions have been subdivided into about 20 stratigraphic sequences. The results are: (1) A more acurate and higher resolution stratigraphy, (2) Greater constraints on basin palaeoenvironmental and palaeogeographic reconstructions, (4) Fully integrated sandstone fairway models, with increased ability to reservoir and seal quality and continuity, (5) In addition to several obvious giant domal traps, subtler yet significant structural and stratigraphic leads and prospects can be identified, (6) The timing, volume and phase of hydrocarbon generation may be estimated more accurately, to ...

Energy Technology Data Exchange (ETDEWEB)

The Electrochemical Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE`s Electric and Hybrid Propulsion Division (DOE-EHP). The goal of DOE-EHP is to advance promising electric-vehicle (EV) propulsion technologies to levels where industry will continue their commercial development and thereby. significantly reduce petroleum consumption in the transportation sector of the economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R&D contracts on advanced battery and fuel cell technologies for DOE-EHP. This report summarizes the battery-related activities undertaken during the period of October 1, 1991 through March 31, 1992. In this report, the objective, background, technical progress, and status are described for each task. These tasks are structured into the following task areas: 1.0 Project ...

Energy Technology Data Exchange (ETDEWEB)

The Electrochemical Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE's Electric and Hybrid Propulsion Division (DOE-EHP). The goal of DOE-EHP is to advance promising electric-vehicle (EV) propulsion technologies to levels where industry will continue their commercial development and thereby. significantly reduce petroleum consumption in the transportation sector of the economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R D contracts on advanced battery and fuel cell technologies for DOE-EHP. This report summarizes the battery-related activities undertaken during the period of October 1, 1991 through March 31, 1992. In this report, the objective, background, technical progress, and status are described for each task. These tasks are structured into the following task areas: 1.0 ...

Energy Technology Data Exchange (ETDEWEB)

The Electrochemical Technology Program at Argonne National Laboratory (ANL) provides technical and programmatic support to DOE's Electric and Hybrid Propulsion Division (DOE-EHP). The goal of DOE-EHP is to advance promising electric-vehicle (EV) propulsion technologies to levels where industry will continue their commercial development and thereby significantly reduce petroleum consumption in the transportation sector of the economy. In support of this goal, ANL provides research, development, testing/evaluation, post-test analysis, modeling, database management, and technical management of industrial R D contracts on advanced battery technologies for DOE-EHP. This report summarizes the battery-related activities undertaken during the period of July 1, 1992 through September 30, 1992. In this report, the objective, background, technical progress, and status are described for each task. The work is organized into the following task areas: Project Management ...

Energy Technology Data Exchange (ETDEWEB)

Since fuel oil meeting the requirements of current petroleum products can be produced by SASOL F-T synthetic process, the manufacturing process of hydrocarbon fuel oil from the coal-derived synthesis gas, downstream processes are being successively investigated. Mobile M-gasoline, MTG, process which produces gasoline from the natural gas-derived synthesis gas through methanol went into commercial operation in New Zealand in 1986. Although the gasoline suffices the quality of commercial gasoline by both fixed bed and fluidized bed systems, the price and service life of catalyst and control of by-product durene must be improved. Any STG processes have not been completed yet and the yield and quality of gasoline are inferior to those of gasoline produced by the MTG process. Applying two-stage process, the STG process will be more economically effective.(21 refs, 4 figs, 10 tabs)

Energy Technology Data Exchange (ETDEWEB)

The feasibility of using three different solid fuels in chemical-looping combustion (CLC) has been investigated using NiO as oxygen carrier. A laboratory fluidized-bed reactor system for solid fuel was used, simulating a chemical-looping combustion system by exposing the sample to alternating reducing and oxidizing conditions. In each reducing phase 0.2g of fuel was added to the reactor containing 20g oxygen carrier. The experiments were performed at 970{sup o}C. Compared to previously published results with other oxygen carriers the reactivity of the used Ni-particles was considerably lower for the high-sulphur fuel and higher for the low-sulphur fuel. Much more unconverted CO was released and the fuel conversion was much slower for high-sulphur fuel such as petroleum coke, suggesting that the nickel-based oxygen carrier was deactivated by the presence of sulphur. The NiO particles also showed good reactivity with methane and a syngas mixture of 50% H{sub 2} and ...

International Nuclear Information System (INIS)

Combustion noise, knock and ignition limits data are measured and presented for a dual fuel engine running on dual fuels of Diesel and three gaseous fuels separately. The gaseous fuels used are liquefied petroleum gas, pure methane and compressed natural gas mixture. The maximum pressure rise rate during combustion is presented as a measure of combustion noise, and the knocking and ignition limits are presented as torque output at the onset of knocking and ignition failure. Experimental investigation on the dual fuel engine revealed the noise generated from combustion, knocking and ignition limits for all gases at different design and operating conditions. A Ricardo E6 Diesel version engine is converted to run on dual fuel of Diesel and the tested gaseous fuel and is used throughout the work. The engine is fully computerized, and the cylinder pressure data, crank angle data and engine operating variables are stored in a PC for off line analysis. The effects of ...

Energy Technology Data Exchange (ETDEWEB)

The increase in world oil prices since 2003 has prompted renewed interest in producing and using liquid fuels from unconventional resources, such as biomass, oil shale, and coal. This book focuses on issues and options associated with establishing a commercial coal-to-liquids (CTL) industry within the United States. It describes the technical status, costs, and performance of methods that are available for producing liquids from coal; the key energy and environmental policy issues associated with CTL development; the impediments to early commercial experience; and the efficacy of alternative federal incentives in promoting early commercial experience. Because coal is not the only near-term option for meeting liquid-fuel needs, this book also briefly reviews the benefits and limitations of other approaches, including the development of oil shale resources, the further development of biomass resources, and increasing dependence on imported petroleum. A companion ...

Energy Technology Data Exchange (ETDEWEB)

The Cement Bond Log Advisor is an expert system being developed to assist users in the design, evaluation, and interpretation of cement bond logs (CBL's). CBL's are produced by sonic tools run after the casing is cemented in a well to determine how well the cement is bonded to the casing and formation and whether a cement squeeze jog should be attempted. During the development of program, two particular challenges were encountered and resolved in ways that might be of general interest to developers of expert system applications for the petroleum industry. The first challenge was to find an efficient and effective method for guiding the user in correlating and interpreting the relationships between multiple sources of continuous visual data (the various waveforms making up the log output). Second, the nomographs, which correlate log amplitudes with cement compressive strength and are used in the log interpretation, were derive from empirical data ...

Science.gov (United States)

The US Department of Energy is carrying out a program of research and development to establish the capability to produce synthetic liquid fuels from coal. According to the National Energy Policy Plan IV, the Assistant Secretary of Fossil Energy is charged with carrying out a program to foster an adequate supply of energy at reasonable cost through innovative, long-term R and D. The payoff for this kind of research is potentially high if the country should need the capability on short notice. However, the research is also high risk in terms of the expectation of process for synthetic fuels to turn a profit for a private sector company. As the date when commercial quantities of synfuels will be needed has retreated before lower real prices of petroleum, the US DOE program for coal liquefaction has evolved to give increasing support to longer range, more exploratory technologies, rather than those nearly developed to the point where commercialization is possible. ...

Energy Technology Data Exchange (ETDEWEB)

Accomplishments for the quarter are presented for the following areas of research: oil shale, tar sand, coal, advanced exploratory process technology, and jointly sponsored research. Oil shale research includes; oil shale process studies, environmental base studies for oil shale, and miscellaneous basic concept studies. Tar sand research covers process development. Coal research includes; underground coal gasification, coal combustion, integrated coal processing concepts, and solid waste management. Advanced exploratory process technology includes; advanced process concepts, advanced mitigation concepts, and oil and gas technology. Jointly sponsored research includes: organic and inorganic hazardous waste stabilization; development and validation of a standard test method for sequential batch extraction fluid; operation and evaluation of the CO[sub 2] HUFF-N-PUFF Process; fly ash binder for unsurfaced road aggregates; solid state NMR analysis of Mesa Verde Group, Greater Green River ...

Energy Technology Data Exchange (ETDEWEB)

In China, the conventional utilization of oil shale is concentrated mainly on retorting oil shale to produce shale oil and fuel gas, and burning oil shale to generate electricity. The growth of petroleum price, and the development in heavy industry, make these conventional utilization facilities become unavailable on the energy market. In this paper, a new comprehensive utilization system is recommended for the future use of Huadian oil shale, based on the current status of energy and the characteristics of oil shale. The system involves three subsystems: retort subsystem, where coarse oil shale (8-80 mm) is retorted to shale oil, hydrocarbon gases and oil shale semicoke; combustion subsystem, where the mixture fuel of oil-shale semicoke and fine oil shale (0-8 mm) is fed to a circulating fluidized bed (CFB) furnace to burn, in order to generate high-pressure steam which is used to supply heat and generate electricity via a traditional steam-electric power mode; ...

Energy Technology Data Exchange (ETDEWEB)

Many problems in physics necessitate the solution of equations which develop sharp gradients, such as shocks. These include atmospheric shocks near the earth's surface, plasma physics phenomena, both in the laboratory and in space, combustion, petroleum reservoir modelling, and light propagation in glass fibers. To deal with this situation, methods are needed which place a high density of nodes in the neighborhoods of the steep gradients. One of the most promising of these methods is the moving finite element method which was first invented by Miller. This approach, in which the nodes are moved so as to minimize the residual error, has been used successfully by Gelinas, Doss, and co-workers to study several different one-dimensional problems and shows great promise as well in dealing with two dimensions. A paper describing the one-dimensional results has already been published, and a paper describing the two-dimensional results is in preparation. The ...

Energy Technology Data Exchange (ETDEWEB)

Slowly, scientists come to realize that there are huge quantities of natural methan hydrates and their interest is awakened. Important questions in this connection are their possible use as future energy sources, the consequences of using methan hydrates on the climate, their integration into the carbon cycle, the cementation of the continental slopes by gas hydrates and their stability and their role in some geological-biological-geochemical processes, especially in the marine area. Towards the end of the 20th century, the basic problems and applied problem scenarios, e.g. the foundation of production platforms dor petroleum and natural gas in gas-hydrate-containing sediments, was the reason for Japan, Canada, USA, China, Germany and India to install national research programmes of various sorts in order to deal with the problems of gas hydrates. Also international programmes like the INTEGRATED OCEAN DRILLING PROGRAM (IODP) and the INTERNATIONAL CONTINENTAL ...

International Nuclear Information System (INIS)

This report presented some quick facts about oil and gas pipelines in Turkey and presented opportunities for trade. The key players and customers in the oil and gas sector were described along with an export check list. Turkey is looking into becoming an energy bridge between oil and gas producing countries in the Middle East, Central Asia and Europe. The oil and gas sectors are dominated by the Turkish Petroleum Corporation, a public enterprise dealing with exploration and production, and the State Pipeline Corporation which deals with energy transmission. They are also the key buyers of oil and gas equipment in Turkey. There are several pipelines connecting countries bordering the Caspian Sea. Opportunities exist in the areas of engineering consulting as well as contracting services for oil and gas pipeline transmission and distribution. Other opportunities lie in the area of pipeline construction, rehabilitation, materials, equipment, installation, and ...

Energy Technology Data Exchange (ETDEWEB)

Due to the improvement of algorithm and the advancement of calculation performance, the imaging by depth migration before stacking is being put into practice from the viewpoint of both calculation cost and accuracy. A lot of imaging examples have been already reported from the survey areas with complicated velocity structures, such as the North Sea and the Gulf of Mexico. Effectiveness of the method has been confirmed. For imaging techniques in Japan National Oil Corporation and Japan Petroleum Exploration Co., Ltd., high-speed depth migration before stacking and high efficiency velocity structure estimation technique have been investigated. This paper describes necessary care to be taken when using depth focusing analysis (DFA) for correcting a velocity model, as an interim stage of case study. The results of depth migration before stacking using dip moveout (DMO) velocity were further inferior to the section obtained by the migration after tracking. Tendency of ...

Energy Technology Data Exchange (ETDEWEB)

Recent organic geochemical studies differ radically in their interpretation of the origin of the Gulf coast oils. However all studies since (and including) Thompson, et al. 1989, emphasize the considerable geographic variation in genetic oil types and are in generalized agreement as to the genetic oil types present and their spatial and stratigraphic relationships. In particular it is accepted that the Gulf rim (both north and south) is encircled by a ring of Mesozoic carbonate-sourced oils and that there is also at least one major deep water trend of carbonate-sourced oils in the northern Gulf. It is also generally agreed that many of the Gulf rim oils are of Oxfordian-Kimmeridgian age, though some, like the Sunniland oils of Florida, are of lower Cretaceous origin. Major disagreement still occurs over the sources of the Louisiana offshore oils and onshore Wilcox reservoired oils. One {open_quotes}school of thought{close_quotes} assigns all these oils to Mesozoic sources. The other ...

Energy Technology Data Exchange (ETDEWEB)

Live cores were obtained from five reservoirs using special precautions to prevent contamination by exogenous microorganisms and minimize exposure to oxygen. The depths from which the cores were obtained ranged from 2,705 ft to 6,568 ft. Core plugs were cut radially from live cores, encased in heat-shrink plastic tubes, placed in core holders, and fitted with inlets and outlets. Nutrient additions stimulated the in-situ microbial population to increase, dissolve stratal material, produce gases, and release oil. Reduction in flow through the core plugs was observed in some cases, while in other cases flow was increased, probably due to the dissolution of carbonates in the formation. A field demonstration of the ability of the in-situ microbial population to increase oil recovery by blocking the more permeable zones of the reservoir is currently underway. This demonstration is being conducted in the North Blowhorn Creek Unit situated in Lamar County, Alabama. Live cores were obtained ...

Energy Technology Data Exchange (ETDEWEB)

Operable Unit 2 at Eielson Air Force Base (AFB) near Fairbanks, is one of several operable units characterized by petroleum, oil, and lubricant contamination, and by the presence of organic products floating at the water table, as a result of Air Force operations since the 1940s. The base is approximately 19,270 acres in size, and comprises the areas for military operations and a residential neighborhood for military dependents. Within Operable Unit 2, there are seven source areas. These source areas were grouped together primarily because of the contaminants released and hence are not necessarily in geographical proximity. Source area ST10 includes a surface water body (Hardfill Lake) next to a fuel spill area. The primary constituents of concern for human health include benzene, toluene, ethylbenzene, and xylenes (BTEX). Monitored data showed these volatile constituents to be present in groundwater wells. The data also showed an elevated level of trace metals in ...

Energy Technology Data Exchange (ETDEWEB)

Until now the assumption has been that synthesis gas - mixtures of carbon monoxide and hydrogen - would be the principal source for many of the chemicals and fuels to be made via C/sub 1/ chemistry. Efforts to make cheap synthesis gas continue. But the pressure to circumvent the stranglehold that OPEC has on petroleum has caused other avenues to be explored. The current oversupply of natural gas offers an interim solution to the problem of nonpetroleum alternate source materials for C/sub 1/ chemicals production. The paper discusses the constraints and advantages of four processes: conventional steam reforming, steam reforming with oxygen secondary, partial oxidation, and catalytic partial oxidation. The end product in all cases is methanol. Direct use of methanol as a fuel has encountered numerous difficulties. conversion of methanol is, thus, of more immediate interest in C/sub 1/ chemistry. The Mobil MTG process and its second-generation modifications, both ...

Energy Technology Data Exchange (ETDEWEB)

This project is a seven year plan starting from 1997, and is aiming at developing vehicles that use the clean energy instead of petroleum, consume 1/2 of the running energy and discharge 1/2 of the CO{sub 2} of the existing vehicles. The research and development are respectively conducted for every kind of vehicles. Namely, for cars, the developments focus on methanol improved fuel battery cars and ANG series hybrid vehicles carried with flywheel battery. For 2 ton loading trucks, they are CNG self-ignition ceramics engine, capacitor/battery in combination use, series hybrid vehicles in combination with discharge energy recovery technology, CNG rarefaction combustion engine, use of lithium ion battery, and series/parallel hybrid vehicles etc. And, LNG mirror cycle engine, capacitor carrying, series hybrid vehicle, dimethylether engine, flywheel battery or capacitor carrying series hybrid vehicle etc., are for public transportation bus. (NEDO)

Energy Technology Data Exchange (ETDEWEB)

According to an American Petroleum Institute production waste survey reported on by P.G. Wakim in 1987 and 1988, the exploration and production segment of the US oil and gas industry generated more than 360 million barrels (bbl) of drilling wastes, more than 20 billion bbl of produced water, and nearly 12 million bbl of associated wastes in 1985. Current exploration and production activities are believed to be generating comparable quantities of these oil field wastes. Wakim estimates that 28% of drilling wastes, less than 2% of produced water, and 52% of associated wastes are disposed of in off-site commercial facilities. In recent years, interest in disposing of oil field wastes in solution-mined salt caverns has been growing. This report provides information on the availability of commercial disposal companies in oil-and gas-producing states, the treatment and disposal methods they employ, and the amounts they charge. It also compares cavern disposal costs with ...

Energy Technology Data Exchange (ETDEWEB)

BHP Petroleum (BHPP) has now operated the 164 tonne per day Methanol Research Plant (MRP) located on the outskirts of Melbourne, Australia for over one year. This plant was commissioned in 1994 making first methanol on 17th October and has operated since then, selling product by pipeline to two local customers, ICI Adhesives and Borden Australia. The plant is based on the Leading Concept Methanol technology (LCM) licensed from ICI Katalco. Since 1985 BHPP has been involved in the development of Floating Production Storage and Offloading (FPSO) technology for the production of oil and gas offshore. In order to utilize the gas associated with oil on remote offshore oil production facilities the combination of gas conversion to methanol and existing FPSO technology is being investigated. The LCM technology being commercialized at the MRP is part of the strategy to demonstrate and develop LCM technology such that it could be located on the deck of a floating vessel in ...

Energy Technology Data Exchange (ETDEWEB)

Combustion scientists are primarily concerned with the fuels most often burned as energy sources (coal, petroleum products, and natural gas), with the goal of learning to burn them as efficiently, intensely, and cleanly as possible. Discovering those slight rearrangements of chemical bonds that together account for the net chemical transformation is the key to understanding how combustion proceeds. Once these reactions have been defined, the chemist can determine the rate coefficient of each reaction as a function of temperature and assemble the information into flame models. The computer programs that use these models to predict experimental results combine two sets of equations describing (1) the diffusive and reactive rates of change in concentration of all the molecules in the flame and (2) the flow of the reacting gases. Although the details of hydrocarbon-flame models are still disputed, many of their general features are clear and the basic reactions ...

Energy Technology Data Exchange (ETDEWEB)

The ruptured offshore oil well 80 miles from Mexican town of Ciudad del Carmen, which poured 8000 barrels of light oil a day into the Gulf of Mexico, provided marine scientists with the opportunity to monitor the spill and see what happens to petroleum hydrocarbons in sea water. Scientists followed changes in viscosity, surface tension, and buoyancy of individual oil globs as they moved through the water and interacted with the surface slick. Using gas chromatography and mass spectroscopy, chemists are gaining an understanding of the unique characteristics of the oil. Computer-generated models projected the slick's movement in the Gulf in response to wind and wave pressures, but the sophisticated system did not give an accurate daily prediction. Immediate damage to fish, turtles, and sea birds was documented by tagging. Long-term effects will take longer to ascertain since 25 years is generally required to flush oil out of sediments. Fishermen do not agree ...

Energy Technology Data Exchange (ETDEWEB)

For many decades, the oil shale resources of the western United States have been considered possible contributors to the Nation's liquid fuel supply. This volume reviews several paths to development of these resources and the likely consequences of following these paths. A chapter providing background information about the nature of oil shale is followed by an evaluation of technologies for recovery of shale oil. The economics and finances of establishing an industry of various sizes are analyzed. The fact that much of the best shale is located on Federal land is examined in light of the desire to increase use of the resources. The consequences of shale development in terms of impact on the physical and social environments, and a discussion of the availability of water complete the report. Policy options addressing barriers that could hinder the establishment of the industry are presented. These options, designed primarily for Congressional consideration, are limited to the ...

Energy Technology Data Exchange (ETDEWEB)

Geothermal energy is one of the more promising renewable energy technologies because it is environmentally benign and, unlike most renewable energy sources, can provide base power. This report provides an assessment of the research and development (R&D) work underway in geothermal energy in the following countries: Denmark, France, Germany, Italy, Japan, Russia, and the United Kingdom. While the R&D work underway in the US exceeds the R&D efforts of the other countries, the lead is eroding. This erosion is due to reductions in federal government funding for geothermal energy R&D and the decline of the US petroleum industry. This erosion of R&D leadership is hindering commercialization of US geothermal energy products and services. In comparison, the study countries are promoting the commercialization of their geothermal energy products and services. As a result, some of these countries, in particular Japan, will probably have the largest share ...

Energy Technology Data Exchange (ETDEWEB)

Negative ion electrospray ionization (ESI) coupled with high field Fourier transform ion cyclotron resonance mass spectrometry (FT-ICR-MS) allows for the direct detection of acidic NSO compounds in petroleum. The technique requires no chromatographic separation, is able to distinguish 18 different compound classes (e.g., neutral nitrogen, carboxylic acids and oxygenates), and can identify {approx}14,000 distinct masses by ultra-high mass resolution and mass accuracy. We previously studied three crude oils from different geological origins [Organic Geochemistry 33 (2002b) 743-759]. Here, we expand our research by comparing two source-equivalent Smackover oils of different levels of thermal maturity. We observe clear differences in the distribution of NSO compound classes, types (number of rings plus double bonds within a class), and number of alkyl carbons. With increasing thermal stress, the relative amount of sulfur and oxygen containing compounds decreases, ...

Energy Technology Data Exchange (ETDEWEB)

Artificial neural network analysis is found to be far superior to multiple regression when applied to the evaluation of trap quality in the Northern Kuqa Depression, a gas-rich depression of Tarim Basin in western China. This is because this technique can correlate the complex and non-linear relationship between trap quality and related geological factors, whereas multiple regression can only describe a linear relationship. However, multiple regression can work as an auxiliary tool, as it is suited to high-speed calculations and can indicate the degree of dependence between the trap quality and its related geological factors which artificial neural network analysis cannot. For illustration, we have investigated 30 traps in the Northern Kuqa Depression. For each of the traps, the values of 14 selected geological factors were all known. While geologists were also able to assign individual trap quality values to 27 traps, they were less certain about the values for the other three traps. ...

Energy Technology Data Exchange (ETDEWEB)

Tribological performance of alumina and silicon carbide ceramics as well as of the hardened steel 100Cr6 for reference was studied during reciprocating sliding and cavitation erosion in isooctane as substitute of gasoline and in distilled water. It was the aim to characterize effects of surface finish of the specimens and the liquid media on friction, resistance to sliding wear and cavitation erosion. Sliding wear tests were run on the self-mated ceramics and ceramic/steel pairs under conditions of boundary lubrication using a laboratory tribometer with cylinder-on-plate geometry. Vibratory cavitation erosion tests were conducted according to ASTM G 32-92. High initial surface roughness of coarse ground specimens led to a distinct running-in period during sliding contact with a transition from high to low values of friction coefficient and wear intensity. Incubation time was reduced with increasing surface roughness in the cavitation tests. Depending on the ...

Energy Technology Data Exchange (ETDEWEB)

Canada's offshore Atlantic petroleum industry is celebrating its tenth anniversary in 2001. This article chronicles the development of the industry discussing the many challenges and setbacks and the eventual triumphs that accompanied the industry's development over the years. Highlights discussed include shipping first oil from the Cohasset Field in July 1992; the financial crisis caused by the withdrawal of Gulf Oil from the Hibernia consortium in the same year; new funding and the beginning of the gravity-based structure construction at Bulls Arm in 1993; striking oil in the Hibernia Field in 1994; the start of exploration and development of the Terra Nova field by Petro-Canada in the same year, based on the floating production, storage and offloading (FPSO) system, which heralded a new era of offshore development in eastern Canada. Approval by the Nova Scotia government of the third and final phase of the Sable Offshore Energy Project followed ...

Energy Technology Data Exchange (ETDEWEB)

This report presents an assessment of the potential energy savings that could accrue from the use of alternative fuels in future transportation engines. Alternative fuels are defined in this study as hydrocarbon fuels which possess characteristics that assure user safety and satisfaction, but require less energy to produce than conventional specification fuels produced from the same resource. In particular, the energy requirements for producing such fuels from domestic coal and oil shale resources are examined from the standpoint of their adaptability to engine types having a high potential for achieving significant efficiency gains over existing transportation engines. Incentives for specific types of engine development are identified in terms of energy savings above those obtainable with current specification fuels. While engine research and development incentives historically are based on economic trade-offs between the fuel and the engine, no attempt is made in this study to ...

Energy Technology Data Exchange (ETDEWEB)

Apatite fission track analysis, vitrinite reflectance data, and K-Ar dating of Permian-Carboniferous and Mesozoic core samples have been successfully integrated to reconstruct the thermal and tectonic history of the Ordos basin, China. Apatite fission track ages of Carboniferous-Jurassic sedimentary rocks range between 3 and 137 Ma, and are significantly younger than the stratigraphic ages. Confined fission track lengths demonstrate exclusively mixed length distribution, indicating complex thermal history. The data suggest that the samples must have all experienced higher paleotemperatures in the past. Mean virtinite reflectance values (R{sub o}) of the Triassic rocks range from 0.61 to 1.06%, giving a high coalification gradient of 0.36%/km and suggesting a high paleothermal gradient of 57{degrees}C/km. Permian-Carboniferous rocks have R{sub o} values on the order of 1.0-3.0%, and locally up to 4.0-6.0%. Some high R{sub o} values coincide with positive gravity and magnetic anomalies. ...

Energy Technology Data Exchange (ETDEWEB)

This spring, Newfoundland will send off a floating production, storage and offloading (FPSO) vessel to the offshore Terra Nova field. The Terra Nova will proceed southeast through Bull Arm, then northeast out of Trinity Bay, then heads southeast to the Jeanne d'Arc Basin on the Grand Banks. The Terra Nova is expected to produce 115,000 barrels of oil per day for six years, when it reaches full capacity. The consortium, headed by Petro-Canada as senior ownership partner and operator, built an environment protection program into every aspect of the project. Some of the features of the environment protection program include glory holes excavated on the ocean floor for the protection of production equipment from icebergs, to a flare stack on the platform, which has four legs to provide stability in rough seas. The FPSO was designed to withstand sea ice, icebergs, and severe winter storms. Flow lines are also protected, and in the event that a line is damaged, sea water will leak ...

Energy Technology Data Exchange (ETDEWEB)

The mass deployment of electric and plug-in hybrid electric vehicles (EVs and PHEVs) that rely on low greenhouse gas (GHG) emission electricity generation has great potential to significantly reduce the consumption of petroleum and other high CO2-emitting transportation fuels. The vision of the Electric and Plug-in Hybrid (EV/PHEV) Vehicles Roadmap is to achieve by 2050 the widespread adoption and use of EVs and PHEVs, which together represent more than 50% of annual LDV (light duty vehicle) sales worldwide. In addition to establishing a vision, this roadmap sets strategic goals to achieve it, and identifies the steps that need to be taken to accomplish these goals. This roadmap also outlines the roles and collaboration opportunities for different stakeholders and shows how government policy can support the overall achievement of the vision. The strategic goals for attaining the widespread adoption and use of EVs and PHEVs worldwide by 2050 cover the development of ...

Energy Technology Data Exchange (ETDEWEB)

The Georges Bank, off southwestern Nova Scotia, is one of the most biologically productive continental shelf ecosystems in the world. It supports a wide diversity of species, including many seabirds. In 1988, federal and provincial legislation placed a moratorium on petroleum exploration and drilling on the Georges Bank, directing the ministers of Natural Resources Canada, and of the Nova Scotia Department of Natural Resources to make a decision regarding the moratorium by January 1, 2000. This report by the Ecology Action Centre (EAC) asks the Georges Bank Review Panel to recommend extending the moratorium on Georges Bank and adjacent areas until 2012, in part to match the American moratorium. Other reasons why the panel made this recommendation were explored. The principal reason is the EAC concern that when the moratorium is lifted, several oil and gas developments will proceed in this ecologically significant offshore area that could result in the loss of the ...

International Nuclear Information System (INIS)

No information on steam/water two-phase flow behavior in large diameter pipes (10 inch or larger) at elevated pressures is available in the open literature. However, there are many applications, in the nuclear, chemical and petroleum industries among others where two-phase flows in large diameter pipes at elevated pressures and temperatures are encountered routinely or under accident scenarios. Experimental data on steam-water two-phase flow in a large diameter (20 inch, 50.08 cm I.D.) vertical pipe at elevated pressures and temperatures (2.8 MPa/230 C--6.4 MPa/280 C) have been obtained. Void fraction, two-phase mass flux, phase and velocity distributions as well as pressure drop along the test pipe have been measured using the Ontario Hydro Technologies (OHT) Pump Test Loop. The void fraction distributions were found to be axially symmetric and nearly flat over a wide range of two-phase flow conditions. The two-phase flow regime could be inferred from the dynamic ...

International Nuclear Information System (INIS)

Smugglers, who make use of the Ukraine-Slovak border for their business, might be satisfied after last week. The Slovak government ordered the switching off of scanning equipment monitoring the movement of goods by train through the Matovce border line. The modern equipment was substituted by people, who aren't able to check freight cars as effectively as gadgets. Not only in Ukraine are they celebrating this success in corruption, who demanded the shut-off of the scanning equipment The bosses on the Slovak side are also rubbing their hands. As told to TREND by Margareta Grecova, spokeswoman for Cargo Slovakia, 90% of goods that cross through the border at Matovce are unloaded. The most frequently transported commodities are ore, coal, chemical and petroleum products. Smugglers put their consignments among iron ore and coal. They prefer goods with high consumer taxes. Besides alcohol, there are mainly cigarettes. These are put into boxes which are concealed in ...

Energy Technology Data Exchange (ETDEWEB)

The objective of the project was to develop a welded tubular joint database to assess the fatigue design curves (X and X{prime}) in the American Petroleum Institute design code (API RP2A). Changes in the curve-fitting method and screening criteria (primarily the exclusion of the very thin tubular joints) produced results different from those reported previously. The current results show that the X and X{prime} curves are too conservative and that a new curve should be adopted. The Department of Energy T{prime} curve was found to be consistent with the screened tubular joint air data and is recommended for use in API RP2A. The weldment size effect exponent (n) of 0.25 in the current version of API RP2A was found to be too small, and a higher value of 0.30 consistent with the Department of Energy recommendations is recommended. The fatigue test results for tubular joints tested in air and tubular joints tested in sea water with cathodic protection are the same at ...

Energy Technology Data Exchange (ETDEWEB)

The major focus of this oil-shale investigation has been on specific localities of oil-shale resource potential. Three main areas of oil-shale occurrence have been studied in detail: the Elko area, Pinon Range area, and Coal Mine Canyon. Geologic mapping, stratigraphic studies, and sampling to delimit the lateral extent of the oil shale deposits were in progress prior to the cooperative agreement with Nevada DOE. These surface geologic studies have been summarized in this report. The results of surface geologic studies conducted near Elko suggested that the Elko area represented the best and most accessible oil-shale deposits; therefore, the Elko area was selected as the site of a shallow exploratory drilling program. Essential to this study was the obtaining of fresh, unweathered oil-shale samples from the Elko area. The samples were obtained from the core-drilling program and tested for oil yield by Fischer assays. The oil yields determined from these samples, together with the ...