We investigated the association between biomarkers of dermal exposure, naphthyl-keratin adducts (NKA), and urine naphthalene biomarker levels in 105 workers routinely exposed to jet-fuel. A moderate correlation was observed between NKA and urine naphthalene levels (p?=?0.061). The NKA, post-exposure breath naphthalene, and male gender were associated with an increase, while CYP2E1*6 DD and GSTT1-plus (++/+-) genotypes were associated with a decrease in urine naphthalene level (p?0.0001). The NKA show great promise as biomarkers for dermal exposure to naphthalene. Further studies are warranted to characterize the relationship between NKA, other exposure biomarkers, and/or biomarkers of biological effects due to naphthalene and/or PAH exposure. PMID:21961652
The mixture of lauric acid and capric acid is a potential latent heat storage material. However, its eutectic melting temperature is quite high for low-temperature thermal energy storage. Addition of naphthalene is proposed. The ternary system lauric acid-capric acid-naphthalene has been investigated by differential scanning calorimetry (DSC), visual polythermal and chromatography of gases. The phase diagram is of an incongruent eutectic type. The eutectic mixture contains 18.4mol% lauric acid, 63.1mol% capric acid and 18.5mol% naphthalene and melts at 13.3{sup o}C. The peritectic mixture contains 32.4mol% lauric acid, 48.2mol% capric acid and 19.4mol% naphthalene and peritectic temperature of 16.2{sup o}C. The incongruent compound was analysed to be CH{sub 3}(CH{sub 2}){sub 10}COOH.CH{sub 3}(CH{sub 2}){sub 8}COOH. The melting temperature of the lauric acid-capric acid-naphthalene ...
Most of the general population is exposed to carbaryl and other contemporary-use insecticides at low levels. Studies of laboratory animals, in addition to limited human data, show an association between...Full Text Available
The comparative analysis of plant hormones was undertaken on a 1-naphthaleneacetic acid tolerant mutant and normal tobacco (Nicotiana tabacum cv Xanthi) plantlets. The mutant plantlet...Full Text Available
This paper presents the corrosion inhibition performance of soluble self-doped copolymers of aniline and 4-amino-3-hydroxy-naphthalene-1-sulfonic acid synthesized by chemical oxidative polymerization method. The corrosion inhibition behaviour of the copolymers in 1.0M HCl has been evaluated using Tafel Extrapolation method and electrochemical impedance spectroscopy (EIS) which was also used to propose the mechanism besides surface morphology. The results showed that the copolymer film exhibited the significant shifting in the corrosion potential and greater charge transfer resistance. The corrosion inhibition efficiency was found to increase from 50% to 90% by increasing the concentration of copolymer from 10 to 70mg/l in HCl medium. Moreover, the copolymer showed the larger degree of surf...
The results of the investigations show that magnetic treatment is a quite practical and effective method of intensifying certain technological processes in the coking industry. Magnetic treatment was utilized for improving the production of ammonium sulfate, refining of the naphthalene fraction, removal of sludge from wash oil in the benzol division, and the treatment of tar before fractionation. 2 references, 3 tables.
Pretreatment of brown coal in oil was conducted using 1-methyl naphthalene or mixture of tetralin and 1-methyl naphthalene as solvent at temperatures ranging from 300 to 430{degree}C under nitrogen atmosphere. Effects of the solvent properties on the structural change of oxygen-functional groups (OFG) and coal liquefaction were investigated by means of quantitative analysis of OFG and solid state {sup 13}C-NMR measurement. When hydrogen transfer from solvent was insufficient, it was suggested that brown coal molecules loose their hydrogen to be aromatized. While, at lower temperatures ranging from 300 to 350{degree}C, hydrogen contained in brown coal molecules was consumed for the stabilization of pyrolytic radicals, and the deterioration of liquefaction was not observed. When hydrogen transfer from solvent was insufficient at higher temperatures above 400{degree}C in nitrogen atmosphere during pretreatment in oil, crosslinking like benzofuran ...
Phenanthrene and naphthalene sorption isotherms were measured for three different series of kerogen materials using completely mixed batch reactors. Sorption isotherms were nonlinear for each sorbate-sorbent system, and the Freundlich isotherm equation fit the sorption data well. The Freundlich isotherm linearity parameter n ranged from 0.192 to 0.729 for phenanthrene and from 0.389 to 0.731 for naphthalene. The n values correlated linearly with rigidity and aromaticity of the kerogen matrix, but the single-point, organic carbon-normalized distribution coefficients varied dramatically among the tested sorbents. A dual-mode sorption equation consisting of a linear partitioning domain and a Langmuir adsorption domain adequately quantified the overall sorption equilibrium for each sorbent-sorbate system. Both models fit the data well, with r{sup 2} values of 0.965 to 0.996 for the Freundlich model and 0.963 to 0.997 for the dual-mode model for the ...
It has been discovered that when Taiheiyo coal pulverized to 200 mesh or smaller is dispersed in naphthalene, a non-hydrogen-donor solvent, and reacted under hydrogen pressure in the presence of a red mud/sulfur catalyst, the catalyst exhibits activity in the regeneration of hydrogen donor solvents which have been hydrogen-depleted in the course of coal liquefaction. It is already known that inorganic matter contained in coal acts as a catalyst in liquefaction. This suggests that the reported effect of the red mud/sulfur catalyst is due to the iron oxide reacting with the sulfur and forming pyrrhotite. 22 refs., 6 figs., 1 tab.
Research continued on the synthesis of model compounds for coal liquefaction research. This report covers the actual laboratory investigation performed during the reporting period in order to attain the stated objective of the project, viz, the synthesis of a model compound containing tetrahydronaphthalene, naphthalene and phenyl moieties linked by methylene, ethylene and ether bonds. The overall synthetic approach aimed at obtaining the end product has been broken down into three major steps that involve the synthesis of three key reactive intermediates. These are: (1) 3,5-dimethyl-5-bromobenzyl chloride, (2) 1-chloromethylene-2-hydroxytetralin and (3) 2-chloromethylene-1-hydroxynaphthalene.
Although polybrominated naphthalenes (PBNs) are contaminants of the commercial fire retardant fireMaster BP-6, the individual PBN isomers have not been identified. In order to study PBNs possessing an analogous level of bromination to those found in fireMaster BP-6, three synthetic PBN mixtures, averaging 5.0, 5.3, and 5.6 bromines per naphthalene were synthetized and partially characterized. The PBN mixtures were administered to immature male Wistar rats and found to be potent inducers of cytochrome P-450-dependent monooxygenases. At the lowest dose tested, 30 mumol X kg-1, each PBN mixture caused maximal induction of benzo(a)pyrene hydroxylase activity. On the basis of enzyme activities, ligand-binding spectra and sodium dodecyl sulfate-polyacrylamide gel electrophoresis, the PBN mixtures were determined to be 3-methylcholanthrene-type inducers of cytochrome P-450 (P-448), resembling qualitatively the most toxic polyhalogenated biphenyls, ...
Thromboxane A2, the predominant product of arachidonic acid metabolism in the blood platelet, is a potent vasoconstrictor and platelet agonist. During its biosynthesis from cyclic endoperoxide, 12(S)-hydroxy-5Z,8E,10E-heptadecatrienoic acid (HHT) is formed in equal amounts. The further metabolism of HHT, catalyzed by 15-hydroxyprostaglandin dehydrogenase, leads to 12-oxo-5Z,8E,10E-heptadecatrienoic acid (Oxo-HT). Sample workup procedures are described which allow for the sensitive and reproducible determination of these two arachidonic acid metabolites in human plasma by gas chromatography-mass spectrometry in the presence of deuterated analogues as internal standards. HHT is derivatized to the pentafluorobenzyl ester tert-butyldimethylsilyl ether. In order to enable quantification of low concentrations of about 10 pg/ml in nonstimulated human plasma, the samples have to be purified by HPLC. Oxo-HT is derivatized to the pentafluorobenzyl ester, which is purified by ...
Hydrogenation of napthalene to tetralin using activated red mud as catalyst was studied as a typical hydrogen-donor system. Under the chosen reaction conditions, unprocessed red mud resulted in a conversion of napthalene of 3.55%. The most active catalyst, prepared by adding 20 wt% of TiO/SUB/2 to the red mud, followed by acid digestion and re-precipitation, resulted in a 58% conversion of naphthalene. This technology may have an important bearing on processes such as coal hydrogenation or crude-oil-residue processing, where the rate of reaction and product quality may depend upon the rate at which a hydrogen-donor solvent can be re-hydrogenated. (7 refs.)
The effect of air addition on biomass tar conversion in catalytic packed bed crackers was studied using both an isothermal micro reactor and a fluidised bed bench scale biomass gasification set up with down stream tar crackers. The micro reactor was applied for experiments with artificial biomass producer gas containing naphthalene as a model tar compound. Experiments were carried out with inert silica and catalytically active calcined dolomite bed material both with and without air addition. Experimental results with real tar from the fluidised bed bench scale gasification set up were in qualitative agreement with results from the micro reactor experiments. (author)
Red mud has been activated by dissolution in hydrochloric acid and reprecipitation with ammonia. The activated material has been evaluated as a catalyst for the hydrogenation of naphthalene, phenanthrene and pyrene and in the hydroliquefaction of both a high and low rank coal utilizing solvents of high and low hydrogen donating ability. Activation led to a substantial increase in the ability to hydrogenate the model compounds and a significant increase in oil yield was obtained in the hydroliquefaction of a low rank coal in the presence of a poor donor solvent. However, activation did not lead to significant increases in overall yields of liquids in other cases and the activated red mud was significantly less active than a commercial nickel-molybdenum-sulphur catalyst. 27 refs., 1 fig., 5 tabs.
Most of the general population is exposed to carbaryl and other contemporary-use insecticides at low levels. Studies of laboratory animals, in addition to limited human data, show an association between carbaryl exposure and decreased semen quality. In the present study we explored whether environmental exposures to 1-naphthol (1N), a metabolite of carbaryl and naphthalene, and 3,5,6-trichloro-2-pyridinol (TCPY), a metabolite of chlorpyrifos and chlorpyrifos-methyl, are associated with decreased semen quality in humans. Subjects (n=272) were recruited through a Massachusetts infertility clinic. Individual exposures were measured as spot urinary concentrations of 1N and TCPY adjusted using specific gravity. Semen quality was assessed as sperm concentration, percent motile sperm, and percent sperm with normal morphology, along with sperm motion parameters (straight-line velocity, curvilinear velocity, and linearity). Median TCPY and 1N concentrations were 3.22 and ...
Callus cultures derived from pith tissue of Nicotiana tobacum were grown on two media either under continuous illumination or in complete darkness. The first medium limited greening ability of callus grown in the light (3 milligrams per liter naphthalene acetic acid, 0.3 milligram per liter 2-isopentenylaminopurine, Murashige and Skoog salts, and 2% sucrose). The second medium encouraged chlorophyll synthesis (greening) though not shoot formation (0.3 milligram per liter naphthalene acetic acid; 0.3 milligrams per liter 2-isopentylaminopurine). To measure intracellular concentrations, calli were grown for 15 days on these standard media containing (U-/sup 14/C)sucrose. The dry weight proportions of the calli (as a fraction of fresh weight) and many metabolite concentrations nearly doubled in light-grown cells compared to dark-grown cells and increase 30 to 40% on low-auxin media relative to high-auxin media. Glutamine concentrations (from 4 to ...
Callus cultures of Calophyllum inophyllum were established using seed, nodal/ internodal and leaf explants on WPM basal medium supplemented with indole-3-butyric acid (IBA), a-naphthalene acetic acid (NAA), picloram (4-amino-3,5,6-trichloropicolinic acid), and 6-benzylaminopurine (BAP) in different combinations and concentrations with the view to study the influence of hormones on callus induction and the pattern of expression of dipyranocoumarins including anti-HIV, non-nucleoside reverse transcriptase inhibitors inophyllum B and P in callus cultures. 96.01% seed explants, 87.50% nodal/internodal explants and 86.66% leaf explants were converted into calluses when inoculated on WPM supplemented with IBA 4.0mgl-1 along with BAP 1.0mgl-1, IBA 4.0mgl-1, and picloram 6.0mgl-1 along with BAP 2....
Desorption behavior of pyrene, phenanthrene and naphthalene from fullerene, single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs) was examined. Available adsorption space of carbon nanotubes (CNTs) was found to be the cylindrical external surface, neither the inner cavities nor inter-wall spaces due to impurities in the CNTs and restricted spaces (0.335 nm) of the MWCNTs, respectively. Desorption hysteresis was observed for fullerene but not for CNTs. Deformation-rearrangement was proposed to explain the hysteresis of polycyclic aromatic hydrocarbons (PAHs) for fullerene, due to the formation of closed interstitial spaces in spherical fullerene aggregates. However, long, cylindrical carbon nanotubes could not form such closed interstitial spaces in their aggregates due to their length, thus showing no significant hysteresis. High adsorption capacity and reversible adsorption of PAHs on CNTs imply the potential release of PAHs if ...
This is the first time that the adsorption of binary mixtures of polycyclic aromatic hydrocarbons (PAHs) has been studied. This study was carried out at laboratory scale in an experimental apparatus specially designed for this aim: with gas-phase fluorescence, a new detection procedure was used. Experimental conditions, mainly in terms of temperature (150C) and contaminant concentration (approximately 1 ppmv), close to the ones observed in energy generation systems, were applied. The PAH adsorption process interpretation was carried out by recording the experimentally obtained breakthrough curves. After the detection parameter optimization, the influence of adsorbate characteristics in the hot gas cleaning of PAH was studied. In this system, the adsorption of 10 binary mixtures of five PAH (naphthalene (Np), fluorene (Fu), phenanthrene (Phe), fluoranthene (Fl), and pyrene (Py)) on an activated carbon was investigated. It was found that the adsorbent efficiency is ...
PAH biomineralization measurements of yardwaste compost samples indicated heterogeneous distribution of active microorganisms and substantial sequestration of the non-polar substrate in the compost matrix. - The purpose of the study was to evaluate the potential of phenanthrene and fluoranthene biodegradation in yardwaste compost materials. These polynuclear aromatic hydrocarbons were chosen for this work because they are relatively readily biodegradable and ubiquitous in the environment. Compost samples were incubated in biometers with "1"4C-labeled phenanthrene and the evolution of "1"4CO_2 was assessed as a measure of mineralization. The "1"4CO_2 evolution varied widely among replicate biometers, possibly as the result of (1) uneven and patchy colonization of phenanthrene-degrading microorganisms on compost particles, and (2) non-uniform dispersion of the labeled substrate spike into the yardwaste microenvironment. Mineralization of phenanthrene reached about 40% extent of "1"4CO_2 ...
A precise admixtures system is needed when using high-volume fly ash concrete as fresh concrete occasionally undergoes rapid slump loss after mixing, which can cause problems with casting, pumping and finishing of the concrete in hot weather. This paper provided details of a study conducted to implement high-volume fly ash concrete technology in India. Different families of admixtures were investigated to determine their water reduction capacities. A set-retarding admixture was used in some of the concrete mixtures in order to determine its efficacy. An Indian Portland cement was used to create a total of 22 different concrete mixtures. Four different fly ashes were used to replace portions of the concrete. The slump of the fresh concrete mixture was monitored for 2 to 3 hours. Unit weight and temperature of the concrete was measured. Specimens were cast in steel moulds in order to determine the compressive strength and unit weight of the hardened concrete. The concretes were demoulded ...
There are five tasks within this project on thermally stable coal-based jet fuels. Progress on each of the tasks is described. Task 1, Investigation of the quantitative degradation chemistry of fuels, has 5 subtasks which are described: Literature review on thermal stability of jet fuels; Pyrolytic and catalytic reactions of potential endothermic fuels: cis- and trans-decalin; Use of site specific {sup 13}C-labeling to examine the thermal stressing of 1-phenylhexane: A case study for the determination of reaction kinetics in complex fuel mixtures versus model compound studies; Estimation of critical temperatures of jet fuels; and Surface effects on deposit formation in a flow reactor system. Under Task 2, Investigation of incipient deposition, the subtask reported is Uncertainty analysis on growth and deposition of particles during heating of coal-derived aviation gas turbine fuels; under Task 3, Characterization of solid gums, sediments, and carbonaceous deposits, is subtask, Studies ...
Soil gas, soil, and water were assessed for organic and inorganic constituents at the former 19th Street landfill at Fort Gordon, Georgia, from February to September 2010. Passive soil-gas samplers were analyzed to evaluate organic constituents in the hyporheic zone and flood plain of a creek and soil gas within the estimated boundaries of the former landfill. Soil and water samples were analyzed to evaluate inorganic constituents in soil samples, and organic and inorganic constituents in the surface water of a creek adjacent to the landfill, respectively. This assessment was conducted to provide environmental constituent data to Fort Gordon pursuant to requirements of the Resource Conservation and Recovery Act Part B Hazardous Waste Permit process. The passive soil-gas samplers deployed in the water-saturated hyporheic zone and flood plain of the creek adjacent to the former landfill indicated the presence of total petroleum hydrocarbon (TPH) and octane above method detection levels ...