British Library Electronic Table of Contents (United Kingdom)

We prepared macromer-grafted polymers (MGPs) containing suitable polymer side chains for improving solubility and pyrene units for improving adsorption on multiwalled carbon nanotube (MWCNT) surfaces, and demonstrated that these MGPs act as MWCNT solubilizers that improve solubility of MWCNTs in typically poor solvents such as alkanes and that improve flowability of polymer/MWCNT composites. The polydimethylsiloxane (PDMS)-MGPs, synthesized using PDMS macromers and pyrene-containing monomers, improved solubility of MWCNTs not only in chloroform but also in hexane, which is a poor solvent for MWCNTs. Moreover, the addition of PDMS-MGP-adsorbed MWCNTs (MWCNT/PDMS-MGPs) to epoxy resin monomers or polybutylene terephthalate (PBT) drastically reduced the viscosity of the obtained epoxy resin mo...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

In this study, Multi-Walled Carbon Nanotubes (MWCNTs) / Hydroxylapatite (HAp) composites were made to improve mechanical properties by using Spark Plasma Sintering (SPS) method. Slurry 6 mol of CaHPO4#centre dot#2H2O (DCPD), 4 mol calcium hydroxide and MWCNTs were mixed and sintered by using SPS at 5-120 MPa pressure, 1200-1250 deg. C and in vacuum or N2 atmosphere. The fracture toughness of sintered MWCNTs/HAp composites was increased.

Science.gov (United States)

... Descriptors : *POLYMERS, *BINDERS, *HOWITZERS, *COMBUSTIBLE CARTRIDGE CASES, CHEMICAL COMPOSITION, PROPELLING ...

International Nuclear Information System (INIS)

Polymerizing effects of high energy radiation has been found suitable for preparation of wood-polymer composites. In the present work after evaluating polymer products that have been obtained by irradiation method, wood-polymer composites have been prepared by in situ polymerization of vinyl acetate, acrylic acid and acrylic acid/styrene mixture using two samples of Iranian hardwoods, Beech and Hornbeam. These woods and their composites have been tested for their physical and mechanical properties. The results have shown that chemical bonding between polymer and the cell wall component lead to better strength properties in the composites. (author).

British Library Electronic Table of Contents (United Kingdom)

A highly sensitive and stable tris(2,2prime-bipyridyl)ruthenium(II) (Ru(bpy)32+) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)32+ immobilized in the ECL sensor by adsorption of Ru(bpy)32+ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-...

Energy Technology Data Exchange (ETDEWEB)

Multi-walled carbon nanotubes (MWNTs) were modified with poly(hexamethylene adipamide) (also known as Nylon 66) via a controlled polymer solution crystallization method. A 'nanohybrid shish kebab' (NHSK) structure was found wherein the MWNT resembled the shish while Nylon 66 lamellar crystals formed the kebabs. These Nylon 66-functionalized MWNTs were used as precursors to prepare polymer/MWNT nanocomposites. Excellent dispersion was revealed by optical and electron microscopies. Nitric acid etching of the nanocomposites showed that MWNT formed a robust network in Nylon 66. Non-isothermal DSC results showed multiple melting peaks, which can be attributed to lamellar thickness changes upon heating. The crystallite sizes L{sub 100} and L{sup 010} of Nylon 66, determined by WAXD, decreased with increasing MWNT contents. Isothermal DSC results showed that crystallization kinetics increased first and then ...

Energy Technology Data Exchange (ETDEWEB)

A wood/polymer composite was produced by impregnating Ramin wood with methyl methacrylate monomer and subsequently polymerizing it by gamma irradiation. To assess the improvement in compression strength of the wood caused by the polymer impregnation, a microbuckling compression failure mechanism was used to model the compression failure of the composite. Such a mechanism was found to predict a linear relationship between the compression strength and the percentage polymer impregnation (by weight). Uniaxial compression test results at 45({plus minus}5)% and 90({plus minus}5)% relative humidity levels, after being statistically analysed, showed that such a linear relationship was valid for up to 100% polymer impregnation. (author).

Energy Technology Data Exchange (ETDEWEB)

SnO{sub 2}-carbon nanotube (CNT) composite sheets are synthesized using poly(vinylpyrrolidone) to uniformly load a monolayer of SnO{sub 2} nanoparticles onto the surfaces of CNTs and CNT bundles within cross-stacked CNT sheets. When they are used as high-capacity (over 850 mA h g{sup -1}) and binder-free anodes in rechargeable lithium-ion batteries, they exhibit good cycle performance. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

International Nuclear Information System (INIS)

Although some polymer conductors of electricity (ex. Polyanilines) are materials known for more than 100 years, only recently have the interesting chemical, electrical and optic properties of their insulating and conducting forms been recognized. Advances made in the chemistry of polymer conductors have also led to improvements in processing them. This work studies a practical application of these materials: the use of polymer conductors for the remote welding of insulating thermoplastic polymers, using energy from microwaves for the local heating of the union. Many thermoplastics (for ex. Polyethylene) do not absorb, or absorb very little, energy from microwaves. Different conductor materials (conductor polymers, carbon nanotubes), however, heavily absorb energy from microwaves with the resulting heating. In this way the welding zone can be heated without ...

Science.gov (United States)

Near-infrared spectroscopy is a convenient tool for measuring nanotube / carbonaceous impurities

British Library Electronic Table of Contents (United Kingdom)

Abstract Aims: To develop a new nano composite of multi walled carbon nanotubes (MWNTs) with enhanced antimicrobial activity. Methods and Results: A novel antimicrobial nanocomposite [MWNT epilson polylysine (MEPs)] was synthesized via covalent attachment of epilson polylysine on MWNTs with hexamethylene diisocyanate (HDI) as the coupling agent. UV visible spectra and Fourier transform infrared spectra (FT IR) investigations indicate that MEPs is stable, with epilson polylysine leaching effectively eliminated. When compared to MWNTs, the new nano composite MEPs exhibits enhanced antimicrobial activities. In 20 mg l 1 suspensions, significant increases of 72 1, 64 5 and 69% against Escherichia coli, Pseudomonas aeruginosa and Staphylococcus aureus can be observed. The deposited film of MEPs...

Science.gov (United States)

Results are presented of experiments on partial discharge in liquid nitrogen, including insulation breakdown characteristics of liquid nitrogen, partial discharge characteristics of composite insulation systems, lifetime of polymer films, impulse breakdown of polymer films in liquid nitrogen, etc. The partial discharge characteristics of liquid nitrogen are examined with increasing liquid-nitrogen pressure. It is concluded that a composite insulation structure of polymer film and liquid nitrogen can be used as effective electrical insulators at cryogenic temperatures.

Energy Technology Data Exchange (ETDEWEB)

Composites based on pure gypsum and polyester-styrene resin have been prepared using various doses of gamma radiation. Some physical properties of the prepared composites and the influence of irradiation dose on it have been studied as: compression strength, hardness, thermal decomposition temperature in nitrogen or oxygen, and the change in weight in aqueous solutions with different pH values. The glass transition temperature of the pure polymer and the composites increases with increasing the irradiation dose up to a plateau, and the glass transition temperature of the pure polymer is lower than that of the composites. The irradiation dose does not seem to affect the decomposition temperature of the pure polymer or the composites significantly and the decomposition temperature in presence of nitrogen is higher than ...

International Nuclear Information System (INIS)

Wood-polymer composites (WPC) have been prepared of pinewood with different monomers using Gamma radiation: acrylamide, butyl acrylate, butyl methacrylate, styrene, acrylonitrile, and polyester. The polymer loading was determined as a function of monomer concentration and absorbed dose. The data show that polymer loading increases by increasing the monomer concentration. In two cases, BMA and polyester, the polymer loading decreases at high concentrations. This can be explained by the increase of the viscosity. Thus the diffusion of the compound into bulk would be slower. The absorbed dose seems to play a positive role in enhancing the polymer loading by increasing the dose. The mechanical properties, tensile and compression strength, have been improved in the most cases for all monomer concentrations or absorbed doses. Using polyester there was no improvement ...

British Library Electronic Table of Contents (United Kingdom)

The physics and technology of a new class of efficient composite piezoelectrics are described. This material combines nanostructured and micropiezoelectric matrix composites. They consist of a polymer matrix, an insulating nanodimensional phase, and a microdimensional piezoelectric phase. It is shown that the nanostructuring of the near-surface region of polymer-PZT piezoelectric composites greatly improves their piezoelectric, mechanical, and electromechanical characteristics. A plausible mechanism underlying this effect is suggested.

British Library Electronic Table of Contents (United Kingdom)

Dye-sensitized solar cells (DSSCs) based on anatase TiO2 hollow spheres (TiO2HS)/multi-walled carbon nanotubes (CNT) nanocomposite films are prepared by a directly mechanical mixing and doctor blade method. The prepared samples are characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, UV-vis absorption spectroscopy and N2 adsorption-desorption isotherms. The photoelectric conversion performances of the DSSCs based on TiO2HS/CNT composite film electrodes are also compared with commercial-grade Degussa P25 TiO2 nanoparticles (P25)/CNT composite solar cells at the same film thickness. The results indicate that the photoelectric conversion efficiencies () of the TiO2HS/CNT composite DSSCs are dependent on CNT loading in the electrodes. A small amou...

International Nuclear Information System (INIS)

A novel composite film, comprising of hydrophobic ionic liquid (IL), multi-walled carbon nanotubes (MWNTs) and gold nanoparticles (GNP), was fabricated and characterized. The GNP was introduced through electrochemical deposition on IL-MWNT gel film coated glassy carbon electrodes (GCE). Experiments showed that both IL and MWNTs could facilitate the GNP deposition. With GNP the composite film exhibited smaller electron transfer resistance and higher sensitivity in sensing guanine (G) and adenine (A). Under the optimized experimental conditions, the anodic peak currents were linear to the analyte concentration in the ranges of 0.008-2.0 ?M. The detection limits were down to nanomole level after an accumulation of 150 s on open-circuit. In addition, on the composite film coated GCE, the anodic peaks of G and A were well separated, and their response sensitivities kept almost unchanged no matter whether ...

British Library Electronic Table of Contents (United Kingdom)

Abstract The effects of the type of coupling agent and virgin polypropylene (PP) content on the mechanical properties and water absorption behavior of recycled low-density polyethylene/wood flour (WF) composites were investigated. The fractured surfaces of these recycled wood/plastic composites (rWPCs) were examined to gain insight into the distribution and dispersion of WF within the polymer matrix. The results indicate that the use of 100% recycled polymer led to inferior mechanical properties and to a greater degree of moisture absorption and swelling when compared to recycled polymer-virgin PP wood/plastic composites. This could have been related to the poor melt strength and inferior processability of the recycled polymer. The extent of improvement of the mechanical properties depende...

International Nuclear Information System (INIS)

The compressive and torsional buckling behavior of carbon nanotube bundles at room temperature is examined with classical molecular dynamics simulation. The critical compressive load and stiffness of a single carbon nanotube in the bundle are found to be similar to those of individual carbon nanotubes. However, the critical torsional moment and stiffness of a single carbon nanotube in the bundle are found to be higher than those of individual carbon nanotubes. In addition, this study demonstrates that van der Waals interactions between the nanotubes in the bundle significantly affect the critical compressive load of the nanotube bundle.

British Library Electronic Table of Contents (United Kingdom)

TaC-4wt.% CNT composites were synthesized using spark plasma sintering. Two kinds of CNTs, having long (10-20mm) and short (1-3mm) length, were dispersed by wet chemistry and spray drying techniques respectively. Spark plasma sintering was carried out at 1850^oC at pressures of 100, 255 and 363MPa. Addition of CNTs leads to an increase in the density of 100MPa sample from 89% to 95%. Short CNTs are more effective in increasing the density of the composites whereas long CNTs are more effective grain growth inhibitors. The longer CNTs are more effective in increasing the fracture toughness and an increase up to 60% was observed for 363MPa sample. Hardness and elastic modulus are found to increase by 22% and 18% respectively for 100MPa samples by addition of long CNTs. Raman spectroscopy, SEM...

International Nuclear Information System (INIS)

This is a preliminary study on the sound absorption properties of two tropical hardwoods, Light Red Meranti and Ramin, and their wood-polymer composites. Sound absorption is measured using a standing wave apparatus. The samples are of one thickness (7 mm) and cut longitudinally. Wood-polymer composites are made by impregnating the samples with methyl methacrylate which is polymerized in situ through #gamma#-irradiation. Both woods and their composites are better sound absorbers at higher sound frequencies. With partial impregnation, the absorption coefficients are improved upon particularly in the region between 1-3 kHz. (author).

International Nuclear Information System (INIS)

The effect of additives on the grafting of a monomer, butylmethacrylate (BA), into simul (a soft wood) has been studied using "6"0Co source at 3 Mrad. The enhancement of polymer loading (grafting) by the addition of minute amounts (1%) of oligomers and of polyfunctional monomers into simul + BA system has been further increased in the presence of acid and urea. The synergistic polymer loading yields by acid addition cause substantial decrease of tensile strength values of wood-plastic composite; but urea increases both polymer loading and tensile strength values synergistically in these systems. (author).

Energy Technology Data Exchange (ETDEWEB)

A highly sensitive and stable tris(2,2'-bipyridyl)ruthenium(II) (Ru(bpy){sub 3} {sup 2+}) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy){sub 3} {sup 2+} immobilized in the ECL sensor by adsorption of Ru(bpy){sub 3} {sup 2+} onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-titania-Nafion showed improved ...

Energy Technology Data Exchange (ETDEWEB)

Considerable interest has focused recently on the use of lignocellulosic fibers as a reinforcement for thermoplastic polymers. The combination of these dissimilar materials, however, is characterized by a widespread incompatibility that leads to a weak fiber/polymer interface and poor performance properties for the composite. In an effort to improve compatibility a number of fiber surface modification approaches have been investigated including plasma, ozone, and polymer grafting treatments. Evaluation of adhesion improvements has been complicated by processing variables that are difficult to control. This paper will discuss the use of the-micro-debond test in quantifying the interfacial shear strength (ISS) in wood fiber/polystyrene composites. Wood fibers were modified to different degrees with styrene-maleic anhydride copolymers that varied in their ...

British Library Electronic Table of Contents (United Kingdom)

In this research, hybrid composite materials were prepared from combination of oil palm Empty fruit bunches (EFB) fibre and jute fibre as reinforcement, epoxy as polymer matrix. This study intended to investigate the effect of jute fiber hybridization and different layering pattern on the physical properties of oil palm EFB-Epoxy composites. Water absorption and thickness swelling test reveal that hybrid composite shows a moderate water absorption which is 11.20% for hybrid EFB/Jute/EFB composite and 6.08% for hybrid Jute/EFB/Jute composite. The thickness swelling and water absorption of the hybrid composites slightly increased as the layering pattern of hybrid composites changed. Hybrid composites are more water resistance and dimensional stable compare to the pure EFB ...

Energy Technology Data Exchange (ETDEWEB)

The resistance of six tropical hardwoods to fungal degradation by two wild-type strains of Phanerochaete chrysosporium Burdsall was investigated using vermiculite burial and wood-block weight loss techniques. Radiation-induced wood-polymer composites (WPC), based on two hardwoods Ramin and Rubberwood with methyl methacrylate, were prepared, and samples were also exposed to the wood-rotting fungus. A significant improvement in resistance to fungal decay was observed in the WPC. Scanning-electron micrographs of the two woods and their composites after fungal degradation are presented and discussed.

Energy Technology Data Exchange (ETDEWEB)

The microstructure of the interphase in semicrystalline polymer matrix composites has a dramatic influence on their mechanical properties. Studies have been performed to alter this region and to correlate various interphase morphologies with changes in fiber-matrix adhesion. A reinforced nylon 66 composite, when subjected to specific thermal histories, contains an interphase composed of transcrystallinity. This region has been altered by coating fibers with a diluent, poly(vinyl pyrrolidone), and/or adding the diluent to the matrix material in very small quantities. Interphase morphology was investigated with optical microscopy, and adhesion was measured using a modified fiber pull-out test. It was found that transcrystallinity increases the interfacial shear strength. The effect different interphase morphologies have on the durability of bulk composite samples is currently under investigation.

International Nuclear Information System (INIS)

Composite materials of synthetics (based on monomers, oligomers and thermoplastics) and of natural polymers (wood and other fibrous cellulosics) prepared by radiation processing, offer valuable structural materials with enhanced coupling forces between the components. The applied polymer chemistry of such composites shows several common features with that of radiation grafting, e.g. the polymerization rate of oligomer-monomer mixtures in wood remains in most cases proportional to the square-root of the initiating dose-rate, just as in the simultaneous grafting, demonstrating that the chain termination kinetics remain regularly bimolecular in the corresponding dose-rate ranges. In the processing experiences of such composites, low dose requirement, easy process-control, and good technical feasibility have been found for composites of wood with oligomer-monomer ...

International Nuclear Information System (INIS)

Nanocomposites comprising nanocrystal silicon (Si), disordered carbon (DC), and multi-walled carbon nanotubes (MWCNTs) - denoted as Si/DC/MWCNTs - have been prepared by pyrolyzing the phenol-formaldehyde resin (PFR) mixed with Si and MWCNTs. This nanocomposite anode material showed a discharge capacity of 1216 mAh/g in the first cycle, and a charge capacity of 711 mAh/g after 20 charge-discharge, much higher than that of Si/DC composite. It can be observed that Si particles wrapped in MWCNTs were homogeneously embedded into the matrix of the DC. The improved electrochemical performance is hypothesized to be mainly attributed to the morphology stability of the composite due to the excellent resiliency and distinct electric conductivity of the MWCNTs.

Energy Technology Data Exchange (ETDEWEB)

The use of WPC as an important insulating material is studied by determining its dielectric constant. The variation of dielectric constant with moisture content is also investigated. Preliminary results show that all untreated woods studied have a higher dielectric constant than their polymer composites with the exception of Kapur and Keruing. It is therefore postulated that the presence of polymers has led to a decrease in the number of polarizable units. Such a material may be useful commercially.

British Library Electronic Table of Contents (United Kingdom)

The electric explosion of a conductor being part of an electric cable is studied. It is ascertained that the electric properties of a polymeric dielectric depend nonlinearly on the maintenance of the ultradisperse metal filler. In the course of the numerous heating-cooling processes of an insulator, a streamlining of the structure of a polymeric composite occurs.

Energy Technology Data Exchange (ETDEWEB)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a {sup 60}Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used.

International Nuclear Information System (INIS)

Wood-plastic composites (WPC) have been prepared with five low-grade woods, native to Syria, using three monomer systems; acrylamide, butylmethacrylate, and styrene, with methanol as the swelling solvent. Polymerization was induced at various radiation doses (10, 20, and 30 kGy) at a dose rate of 3.5 kGy/h using a "6"0Co gamma radiation source. Some physical properties of WPC, namely polymer loading and compression strength have been measured. The polymer loading decreases approximately with increasing density of the wood species used. (author)

Energy Technology Data Exchange (ETDEWEB)

The lithium carbon batteries studied in this paper use plasticized polymer electrolytes made with passive polymer matrix swollen by a liquid electrolyte with a high ionic conductivity (> 10{sup -3} S/cm at 25 deg. C). The polymers used to prepare the gels are polyacrylonitrile (PAN) and vinylidene poly-fluoride (PVdF). The electrochemical and physical properties of these materials are analyzed according to their composition. The behaviour of solid electrolytes with different materials of lithium ion insertion (graphite and LiNiO{sub 2}) are studied and compared to liquid electrolytes. The parameters taken into account are the reversible and irreversible capacities, the cycling performance and the admissible current densities. Finally, complete lithium ion batteries with gelled electrolytes were manufactured and tested. (J.S.) 2 refs.

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the preparation and characterization of polyaniline/TiO{sub 2} composite by XRD, UV-VIS spectra, TGA/DTA and FTIR. The composite is used as a cathode material for rechargeable battery comprising of zinc container as the anode, cellulose acetate as the separator and polyvinyl sulfate and carboxy methyl cellulose as the solid polymer electrolytes (SPE). By using the PAn/TiO{sub 2} composite as the cathode material, the cylindrical AA type rechargeable battery was fabricated and the following output was observed. The open circuit voltage (OCV) is 1.4 V and current is 250 mA to 1.0 A, 50 recharge cycles, power density is 350 A h/kg and power efficiency is 70%.

British Library Electronic Table of Contents (United Kingdom)

Emeraldine base (EB) polymer?ZnO nanoparticles composite films has been synthesized by solution casting technique on ITO-coated glass substrate and characterized by XRD, FTIR and TEM for their structure and morphology. Dielectric behaviour of these composite films has been investigated in the very low frequency region to medium frequency region (1?kHz?1?MHz). The dielectric constant of the composite with 30% nanoparticles is almost one-tenth of the pure EB. The dielectric value becomes constant in the frequency region greater than 400?kHz. The change in dielectric behaviour of the composite is explained on the basis of multilayered interface formed between the ZnO nanoparticles and emeraldine chains. Nanoparticles have high energy surface which is responsible for the decrease of free volum...

International Nuclear Information System (INIS)

Fibre-reinforced-polymer-composite material has been suggested as a bearing material to overcome tribological problems witnessed during the testing of Ram assembly of the 540 MWe fuelling machine at RTD. After successful trials at B-Ram the composite material has been adapted for B-RAM, C-Ram and RDB head at fuelling machines being tested at RTD, Hall 7 and at Tarapur. Laboratory evaluations were also carried out at Tribology Lab RTD to study effect of radiation on the composite. Paper deals with the various aspects of life prediction of this material in term of wear and radiation damage. (author)

Energy Technology Data Exchange (ETDEWEB)

The adverse effect of moisture diffusion on the properties of wood has been one of the main weaknesses of wood. Using a gamma irradiation method, wood-polymer composites have been produced which exhibit significant improvement in mechanical properties like compression, creep deformation and creep rupture particularly at high humidity. It has been thought that the impregnation of polymer into the wood has affected the moisture diffusion in the wood, so that its adverse effects on the mechanical properties has been reduced. In this report the apparent diffusion coefficients of a Ramin wood impregnated with varying amounts of polymethyl methacrylate (PMMA) were determined using a Fick's law approach. An initial linear relationship was found for impregnation of up to 70% PMMA, after which the diffusion coefficient levels off to a maximum value, for the three environmental relative humidity levels of 40, 60 and 90({plus ...

International Nuclear Information System (INIS)

Wood plastic composites are prepared under radiation of "6"0Co gamma source with simul, a low grade wood of Bangladesh using a water soluble monomer acrylamide (AM) mixed with a swelling solvent methanol, water or methanol/water (1:1) at different compositions in the presence of a number of additives and co-additives such as NVP (N-vinylpyrrolidone), TPGDA (tripropylene glycol diacrylate), TMPTA (trimethylol propane triacrylate), sulfuric acid, urea and copper sulfate. Polymer loading (PL) and tensile strength (TS) of the composites are measured. The role of these additives on the composites is also discussed. It is observed that nitrogen-atom containing-materials like urea, NVP and AM produce composites with the highest mechanical strength, and incorporation of copper into this system provides additional property of protection and preservation of the ...

International Nuclear Information System (INIS)

One of the greatest opportunities for using of biomass as a precursor in the production of polymeric materials is the lignocellulose composites that can combine high performance with low costs. This work is a initial study on the production of a lignocellulose reinforced polyethylene composite. A compatibilization made by a induced gamma radiation grafting reaction was used to increase the adhesion between the matrix and the reinforced or filled fibers. The lignocellulose materials were exposed to gamma radiation in order to promote a molecular degradation and increase its reactivity. The polymer, the lignocellulose material and the compatibilization were processed by extrusion and the composite produced by this process were characterized by mechanical tests. (author)

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

British Library Electronic Table of Contents (United Kingdom)

Summary: The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR res...

Energy Technology Data Exchange (ETDEWEB)

The surface coverage of amorphous silica gels used in the synthesis of silica polyamine composites has been investigated by 29Si NMR. By diluting the polyamine anchor silane, chloropropyl trichlorosilane, with methyl trichlorosilane it was found that surface coverage could be markedly improved for a range of amine polymers after grafting to the silica surface. The commensurate decrease in the number of anchor points and increase in the number of free amines results in an increase in metal capacity and/or an improvement in capture kinetics. Solid state CPMAS-13C NMR has been employed to investigate the structure and metal ion binding of a series of these composite materials. It is reported that the highly branched polymer, poly(ethyleneimine) (PEI) exhibits much broader 13C NMR resonances than the linear polymers poly(allylamine) (PAA) and poly(vinylamine) (PVA). These results are ...

International Science & Technology Center (ISTC)

Shungit Filled Polymers for Artificial Bone Articulations

Energy Technology Data Exchange (ETDEWEB)

Wood plastic composite (WPC) has been prepared with a low grade wood simul (Salmalia malabarica) of Bangladesh under Co-60 gamma irradiation using MMA as the bulk monomer combined with methanol as the swelling solvent at different urea concentrations. Effect of a second solute such as NVP, TPGDA and TMPTA in the impregnating solution is evaluated. NVP appears to be the best co-additive/second solute among all the additives used to yield the composite with the highest polymer loading (PL) and tensile strength (TS) at 0.5% urea concentration. (author).

Energy Technology Data Exchange (ETDEWEB)

Wood plastic composites formation has been studied with simul (soft wood, density = 0.4 g/cm{sup 3}) and butylmethacrylate (BA) monomer using 10% methanol as the swelling agent. The effect of additives like sulfuric acid, multifunctional monomers (NVP, TPGDA, TMPTA) and oligomers (PEA, UA and EA) has been investigated using 1-3 Mrad dose at 0.8 Mrad/h. Synergistic polymer yields have been achieved in presence of the additives. The tensile properties of the composite are also reported. (author).

International Nuclear Information System (INIS)

Two species of wood, viz. Haldu (Adina Cordifolia) and Jamun (Syzygium Cumini) were vacuum-impregnated with two styrene-based monomer systems and polymerized in situ with gamma radiation from a cobalt-60 source. The electrical conductivity of these specimens was determined at various polymer loadings under dry conditions, after wetting and after wet recovery as per ASTM standards. The water absorption characteristics are also presented. The results are discussed with special reference to the role of water. Potential applications are also discussed. 7 figures.

Energy Technology Data Exchange (ETDEWEB)

An apparatus was designed and built for the purpose of exposing samples of solid polymers to varying temperatures, atmospheres and stress levels while quantitatively recording the resulting chemiluminescence. Preliminary data were acquired with this apparatus that show a correlation between an enhanced chemiluminescence signal at a low level of applied stress and a decrease in tensile strength for the most commonly used epoxy resin in high performance fiber composites, TGMDA DDS. The studies with cellular silicone cushions (which are used to accommodate thermal expansion and contraction) have defined the temperature regimes in which accelerated aging tests are valid for extrapolation to ambient temperature. Preliminary data on Kevlar fibers is also discussed.

Science.gov (United States)

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network ...

British Library Electronic Table of Contents (United Kingdom)

The integration of the environmental problem in the design of industrial products leads us to incorporate vegetal fibres and recycled polymers into composite materials. The aim of this work is to study the behaviour and the environmental interest of a recycled PP/hemp fibre after several injection cycles. The mechanical and rheological behaviour of recycled PP/hemp composite was first studied by using tensile, dynamical mechanic analysis and rheological measurements. Then, to better understand the influence of the recycling, a morphology study was carried out on composites by using optical and electron microscopy. Finally, we investigated the environmental advantages of our composite thanks to a simplified environmental assessment. Our results highlighted the environmental interest of usin...

Energy Technology Data Exchange (ETDEWEB)

Selected local woods and their wood-polymer combinations or composites (WPC) were tested for their thermal conductivity and their fire resistance. WPC were prepared by polymerizing monomers ''in situ'' in oven dried woods by gamma radiation. The monomers included acrylonitrile (AN), 60% styrene-40% acrylonitrile (STAN), methyl methacrylate (MMA), 95% methyl methacrylate-5% dioxane (MD), and vinylidene chloride (VDC). A reduction in thermal conductivity was exhibited by all the composites prepared. W-PAN showed the greatest reduction in thermal conductivity and W-PSTAN in general showed the least. An explanation is suggested for this behaviour. The polymers PMMA and PMD were found to enhance flammability of the woods while PVDC, PAN, and PSTAN imparted fire resistance to the woods. Of the six local woods studied, Ramin-and-Keruing-polymer ...

International Nuclear Information System (INIS)

There is growing interest in the use of natural fibres as the reinforcements for polymer composites in the automotive industry and as matrix for composites in building products application to replace synthetic fibres. In this respect the aim of this study is to develop an environmental friendly composites for furniture industry based on EFB fibres and sago starch. In this preliminary study, a basic composition and processing of EFB fibres-sago starch composites were established and the properties of the composites were determined. EFB fibre content was varied between 50-80% by weight. The amount of sago starch in liquid form was also varied and final weight percentage of sago starch added into the EFB fibres was adjusted accordingly. The mixtures of EFB fibres and sago starch were blended using Haake Rheomixer. The preliminary results ...

Energy Technology Data Exchange (ETDEWEB)

Utilization of microwaves for heating purposes began in the 1940`s. This new form of energy transfer offers many distinct advantages over conventional heating, such as volumetric, fast, direct, selective, instantaneous, and controllable heating. Studies of microwave processing of polymeric materials in the early 1960`s led to a successful industrial application in the rubber industry. Since the mid-1980`s, there has been a great deal of interest in microwave processing of polymeric materials. Technical issues, such as temperature uniformity and control of thermal runaway during processing, were investigated and many successful laboratory scale results were obtained from both fundamental and processing studies. This paper presents a historical perspective of microwave heating in the processing of polymer composites and discusses possible future directions for technology commercialization.

Energy Technology Data Exchange (ETDEWEB)

We summarize recent developments in x-ray microscopy of polymers by focusing on the characterization of organic electronic devices. The quantitative compositions of model polymer blends have been mapped at a resolution of {approx}35 nm. Since it could be inferred that these devices have structures smaller than 35 nm, quantitative compositional mapping at length scales below the present resolution limit of x-ray microscopy is required. Organic devices thus serve to both highlight the success of NEXAFS microscopy to date, but to also outline the very real need for higher spatial resolution. New approaches to create improved optics or different acquisition modalities are required if x-ray microscopy is to make sustained contributions to such an important area of research as organic devices.

Energy Technology Data Exchange (ETDEWEB)

Thin films of sodium montmorillonite clay and cationic polyacrylamide were grown on a polyethylene terephthalate film using layer-by-layer assembly. After 30 clay-polymer layers are deposited, with a thickness of 571 nm, the resulting transparent film has an oxygen transmission rate (OTR) below the detection limit of commercial instrumentation (< 0.005 cc/m{sup 2}/day/atm). This low OTR, which is unprecedented for a clay-filled polymer composite, is believed to be due to a brick wall nanostructure comprised of completely exfoliated clay in polymeric mortar. With an optical transparency greater than 90% and potential for microwaveability, this thin composite is a good candidate for foil replacement in food packaging and may also be useful for flexible electronics packaging.

Energy Technology Data Exchange (ETDEWEB)

Wood-Polymer Composites (WPC) was prepared from recycled films of agricultural use and wood wastes, and LLDPE and neat PE resin mixture were also utilized in order to compare the properties. Maleic anhydride (MA) and dicumyl peroxide were used as an adhesion promoter and an initiator, respectively. Tensile properties of WPC were measured via tensile test as a function of wood filler and MA content, and fracture surface was also investigated with SEM. As the content of wood filler increased, elongation decreased but modulus increased. However, tensile strength of WPC increased only when MA was used, and 1 wt.% of MA may be high enough to increase the tensile properties. The tensile properties of WPC prepared from recycled PE films were almost same as those of neat PE resin mixture. (author). 18 refs., 5 figs.

International Nuclear Information System (INIS)

The use of polymer matrix composites in aerospace propulsion applications is currently limited by insufficient resistance to erosion by abrasive media. Erosion resistant coatings may provide necessary protection; however, adhesion to many high temperature polymer matrix composite (PMC) materials is poor. A low pressure oxygen plasma treatment process was developed to improve adhesion of CN_x coatings to a carbon reinforced, fluorinated polymer matrix composite. Fullerene-like CN_x was selected as an erosion resistant coating for its high hardness-to-elastic modulus ratio and elastic resilience which were expected to reduce erosion from media incident at different angles (normal or glancing) relative to the surface. In situ x-ray photoelectron spectroscopy was used to evaluate the effect of the plasma treatment on surface chemistry, and electron microscopy was ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Impurity effects on the photon-assisted spin-polarized transport through armchair carbon nanotubes connected with ferromagnetic leads are investigated theoretically. The impurity induces one resonant state whose position depends on the impurity strength, which can break the electron-hole symmetry. Whether the impurity suppresses or enhances the spin-coherent current depends on the nanotube length. When the microwave fields are applied on the nanotube, additional small side peaks caused by the photon-assisted tunneling are found. With increasing the impurity strength, one new current peak appears under the influence of both the microwave fields and the impurity.

Energy Technology Data Exchange (ETDEWEB)

The thermal stability of wood polymer composites made with extractive-free wood from four different wood species was studied. Hot water (HW) extractives, ethanol/cyclohexane (E/C) extractives and both types of extractives were eliminated from A. cyclops, E. grandis, P. radiata and Q. alba. Composites of LLDPE and 10 wt% of wood were prepared, using poly vinyl alcohol-co-ethylene (EVOH) as a compatibilizer. The thermal degradation behavior of the composites was characterized with thermogravimetric analysis (TGA). The obtained results showed that in all cases, the degradation temperatures shifted to higher values after removal of the extractives. The removal of E/C extractives was less effective in its improvement of the thermal stability than the removal of HW extractives. The largest improvement on the thermal stability of WPCs was achieved when both types of extractives (E/C and HW) were removed.

British Library Electronic Table of Contents (United Kingdom)

Abstract Melamine cyanurate (MCA) was utilized as an environmental friendly additive to prepare the nonhalogen flame retardant MCA/Nylon 66 composites by melt blending technique. Because of the strong hydrogen bond interactions and fine interfacial compatibility between MCA and Nylon 66, the resultant even dispersion of MCA filler in polymer matrix leads to the better toughness and strength of MCA/Nylon 66 composites than those of neat Nylon 66. Both Nylon 66 and MCA/Nylon 66 composites exhibit similar -crystalline structure, but the presence of MCA influences the distribution of 1 and 2 crystalline phases in Nylon 66 by inducing its hydrogen-bonded sheet separation. Moreover, the blending of MCA and Nylon 66 increases the crystallization temperature and exothermicity but decreases the the...

Science.gov (United States)

Plastic composites have become a large class of construction material for exterior applications. One of the main disadvantages of wood plastic composites resides in the weak adhesion between the polar and hydrophilic surface of wood and the non-polar and hydrophobic polyolefin matrix, hindering the dispersion of the flour in the polymer matrix. To improve interfacial compatibility wood flour can be pretreated with environmentally friendly methods such as cold-atmospheric pressure plasma. The objective of this work is therefore to evaluate the potential of plasma polymerization of acetylene on wood flour to improve the compatibility with polyolefins. This presentation will describe the reactor design used to modify wood flour using acetylene plasma polymerization. The optimum conditions for plasma polymerization on wood particles will also be presented. Finally preliminary results on the wood flour surface properties and use ...

International Nuclear Information System (INIS)

By means of an audio frequency plasma polymerisation ultra-thin gradient plasma polymer layers were deposited on zinc and zinc-coated iron. The aim was to generate an interfacial polymeric layer which bonds to an oxidised metal as well as to a subsequently applied organic coating and acts as an interfacial barrier layer for ions and water. Surface modifications were done in an in situ plasma cell with infrared reflection absorption spectroscopy (IRRAS). The zinc surface was first activated by an oxygen plasma to provide a freshly oxidised and contamination free oxide surface. The intermediate stages of the surface reactions could be revealed. Carbon dioxide molecules as oxidation products adsorbed on the growing zinc oxide and were desorbed at a later stage. An organosilicon plasma polymer was deposited directly on top of the oxide layer from a hexamethyldisilane (HMDS) plasma. Afterwards a cyclohexene (CHEX)/hexamethyldisilane co-plasma ...

International Nuclear Information System (INIS)

It has been prepared composites materials by means of monomer penetration in pores of wood samples and later curing by means of gamma irradiation. The studied species were Hura crepitans L. (catahua), Aniba puchury-minor (C. Martinez) (mohena amarilla), and Calycophyllum spruceanum (Benth.) (capirona). These new materials exhibit smaller water absorption and better mechanical properties in comparison with native wood. The test tubes of catahua treated with the styrene-polyester mixture absorb only up to 10% humidity compared to the native species whereas its hardness is increased in a 100%. (author).

Energy Technology Data Exchange (ETDEWEB)

Four species of nanocomposites organized by hydroxyapatite (HAp), hyaluronic acid (HyA), chondroitin sulfate (ChS) and type II collagen (Col), i.e. HAp/HyA, HAp/ChS, HAp/HyA/Col and HAp/ChS/Col composites, were synthesized by coprecipitation methods. The composites could retain lots of water: 40%, 32%, 42% and 58% for the HAp/HyA, HAp/ChS, HAp/HyA/Col and HAp/ChS/Col composites, respectively. Transmission electron microscopy observations revealed that the HAp/HyA and HAp/ChS composites consisted of island-like aggregations whose sizes were 300 nm in length and 30 nm in width, and 150 nm in length and 30 nm in width, respectively. In the aggregations, there were many HAp nanocrystals of 20 nm in length, and their c-axes were aligned along the respective polymer molecules through a self-organization process. Animal tests showed that chondrocyte-like cells penetrated into the ...

Science.gov (United States)

The production of water from a subterranean formation is reduced by contacting the formation with a water dispersible hydrophilic organic polymer having a molecular weight greater than 100,000 and containing carboxyl functionality and a crosslinking composition comprising water, a zirconium compound having a value of 4+, an alpha-hydroxy acid and an amine compound.

Energy Technology Data Exchange (ETDEWEB)

A series of N-carbazolyl-substituted silane homo- and copolymers has been prepared by Wurtz coupling. Doping with iodine on these copolymer films increases the electrical conductivity to the range 10{sup -6}-10{sup -3} S cm{sup -1}. The conductivity depends strongly on the composition of the copolymer; it reaches the maximum value for N-carbazolyl-substituted silane homopolymer. The effects of carbazolyl group on conductivity and charge transport mechanisms in the polymer are discussed. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Solid-state nuclear magnetic resonance (NMR) has been used to explore the nanometer-scale structure of Nafion, the widely used fuel cell membrane, and its composites. We have shown that solid-state NMR can characterize chemical structure and composition, domain size and morphology, internuclear distances, molecular dynamics, etc. The newly-developed water channel model of Nafion has been confirmed, and important characteristic length-scales established. Nafion-based organic and inorganic composites with special properties have also been characterized and their structures elucidated. The morphology of Nafion varies with hydration level, and is reflected in the changes in surface-to-volume (S/V) ratio of the polymer obtained by small-angle X-ray scattering (SAXS). The S/V ratios of different Nafion models have been evaluated numerically. It has been found that only the water channel model gives the ...

International Nuclear Information System (INIS)

Wood-plastic composite (WPC) formation has been studied with simul + styrene system at various compositions of styrene with methanol as the swelling solvent. Effect of additives, e.g. multifunctional monomers (MFM)and oligomers used in very low quantity (1% v/v) on the polymer loading (PL) and tensile strength (TS) of the WPC has been elaborately investigated. Enhanced PL and TS values are observed. Inorganic co-additives like Lithium (Li"+), Copper (Cu"2"+) and acid (H"+) and urea (U) used in combinations with additives (MFM or oligomers) have influenced the results of PL and TS in these systems. Li"+ ion has been a good replacement for H"+ ion; U has substantially enhanced the PL values with retention of the TS values of WPC. Co-additive Cu"2"+ used in these systems can act as a preservative and protective agent for WPC. (Author).

British Library Electronic Table of Contents (United Kingdom)

Fluorocarbon polymers are used to enhance thermal stability and electrostatic protection of composite propellant compositions. A precipitation technique has been developed to coat ammonium perchlorate (AP) using a copolymer of hexafluoropropylene and vinylidene fluoride (HFP-VF) with the help of solvent-counter solvent method. The coated AP has been used to prepare propellant compositions in different ratio based on hydroxyl terminated polybutadiene (HTPB), aluminium powder along with uncoated AP and studied for viscosity build-up and visco-elastic behaviour as well as mechanical, ballistic, thermal and sensitivity properties keeping 86% solid loading. The data on viscosity build-up indicate that as the percentage of viton coated AP increases end of mix viscosity and viscosity build-up inc...

British Library Electronic Table of Contents (United Kingdom)

In this work, a highly-sensitive polymeric membrane ion selective electrode for determination of tetracycline was constructed by using molecularly imprinted polymer (MIP) particles as quasi-ionophore. The water-compatible MIP particles targeting tetracycline were synthesized with tetracycline as a template molecule, methacrylic acid as a functional monomer, ethylene glycol dimethacrylate as a cross-linker, 2,2?-azobisisobutyronitrile as an initiator and lanthanum ion as a mediator. Benefited from the distinctive performance of the quasi-ionophore and the optimized composition of the membrane and the inner filling solution, the lower detection limit of the electrode was decreased to about 1 ? 10?8 mol/l. It exhibited a good electrode slope 59.8 mV/decade near the theoretical Nernstian one, ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A control framework was developed for real time implementation of optimal control of emulsion polymerization with multiple monomers by integrating model based algorithms with software engines. The developed system was applied for controlling conversion, particle size, molar mass, and polymer composition using model predictive control (MPC) based on mechanistic models for emulsion polymerization. The control formulation was extended to account for existing process constraints on the input, input moves, and solids content. On experimental testing, the developed control scheme was found to achieve the desired objectives without violating the process constraints and showed good robustness in rejecting disturbances. Improvements in the process operation and polymer property control wer...

International Nuclear Information System (INIS)

Decommissioning of radiological and nuclear installations is for this century the new challenge. One of the performance criteria is the reduction of total quantities of radioactive materials (liquid or solid) arising from dismantling and decontamination of radiological and nuclear installations. In this work we present a new application of the water soluble polymers used as: - flocculation agents in treatment and conditioning process within the management of radioactive liquid materials; - strippable coatings on solid materials based on the water soluble polymers. The parameters of water soluble polymers made in our Institute by radiation processing have been analysed, namely the molecular average weight, composition, and efficiency of utilization of these polymeric materials as well as the content of ash, additives, decontamination factor, consumption per surfaces/liter, corrosion aspects, ...

Energy Technology Data Exchange (ETDEWEB)

The physical properties of polymer blends consisting of one or more crystallizable components are affected by the microstructure of these materials. In particular, the degree of crystallinity can be influenced by processing parameters, and the crystallinity, as well as the phase distribution, may vary as a function of depth through an injection molded part Conventional x-ray diffraction techniques can provide information regarding both phase composition and degree of crystallinity, but, because of the relative transparency of these materials to wavelengths generally available in the laboratory, these techniques provide information representative of only the bulk. By employing parallel beam optics at varying grazing incidence angles, the x-ray sampling depth can be varied without loss of resolution. This technique can be used to vary the effective analysis depth from the top several hundred angstroms for low razing incidence to centimeters for ...

Energy Technology Data Exchange (ETDEWEB)

Porous SnO{sub 2} nanotubes were prepared via electrospinning followed by calcination in air. As anode materials for lithium ion batteries, the porous nanotubes delivered a high discharge capacity of 807 mAh g{sup -1} after 50 cycles. Even after cycled at high rates, the electrode still retained a high fraction of its theoretical capacity. Such excellent performances of porous SnO{sub 2} nanotubes could be attributed to the porous and hollow structure which facilitated liquid electrolyte diffusion into the bulk materials and buffered large volume changes during lithium ions insertion/extraction. Furthermore, the nanoparticles of nanotubes provided the shorter diffusion length for lithium ions insertion which benefited in retaining the structural stability and good rate performance. Our results demonstrated that this simple method could be extended for the synthesis of porous metal oxide ...

Energy Technology Data Exchange (ETDEWEB)

Wood plastic composite (WPC) formation was studied with simul wood and butylmethacrylate (BMA) at different compositions with swelling solvent methanol in the presence of a set of multifunctional acrylate monomer additives like N-vinyl Pyrrolidone (NVP), tripropylene glycol diacrylate (TPGDA) and trimethylol propane triacrylate (TMPTA) at a different doses between 1 and 3 Mrad using Co{sup 60} gamma source. This was further investigated using another set of additives chosen from oligomers such as epoxy acrylate (EA), urethane acrylate (UA) and polyester acrylate (PEA). TMPTA yielded the highest polymer loading at relatively low dose (2 Mrad). Effect of co-additives like sulfuric acid (H{sup +} ions), copper sulphate (Cu{sup 2+} ions) and urea was investigated in these series. Tensile strength (TS) of the composites were determined and the highest TS values were obtained with the ...

Energy Technology Data Exchange (ETDEWEB)

The performance of PAN-based composite absorbers was evaluated in dynamic experiments at flow rates ranging from 25--100 bed volumes (BV) per hour. Composite absorbers with active components of ammonium molybdophosphate (AMP) PAN and K-Co ferrocyanide (KCoFC) PAN were used for separating Cs from a 1 M HNO{sub 3} + 1 M NaNO{sub 3} + 2 {times} 10{sup {minus}5} M CsCl acidic simulant solution. KCoFC-PAN and two other FC-based composite absorbers were tested for separating Cs from alkaline simulant solutions containing 0.01 M to 1 M NaOH and 1 M NaNO{sub 3} + x {times} 10{sup {minus}4} M CsCl. The efficiency of the Cs sorption on the AMP-PAN absorber from acidic simulant solutions was negatively influenced by the dissolution of the AMP active component. At flow rates of 50 BV/hr, the decontamination factor of about 10{sup 3} could be maintained for treatment of 380 BV of the feed. With the KCoFC-PAN absorber, the ...

British Library Electronic Table of Contents (United Kingdom)

We have developed a process for chemical purification of carbon nanotubes for solution-processable thin-film transistors (TFTs) having high mobility. Films of the purified carbon nanotubes fabricated by simple drop coating showed carrier mobilities as high as 164 cm2V?1s?1, normalized transconductances of 0.78 Sm?1, and on/off current ratios of 106. Such high performance requires the preparation of a suspension of micrometer-long and highly purified semiconducting single-walled carbon nanotubes (SWCNTs). Our purification process includes length and electronic-type selective trapping of SWCNTs using recycling gel filtration with a mixture of surfactants. The results provide an important milestone toward printed high-speed and large-area electronics with roll-to-roll and ink-jet device fabri...

Energy Technology Data Exchange (ETDEWEB)

The need for a hydrogen economy is driven by increasing fuel prices, depleting oil reserves and uncertainty over supplies, and concerns about global warming and environmental pollution. Alternative methods to portable energy sources such as fossil fuels are being developed that are more efficient and carbon-emission-neutral. A prospective method is to produce hydrogen as an energy carrier. This paper presented a study on the degradation of materials under conditions of the sulphur-iodine (SI) thermochemical cycle. The paper provided background information on the study and presented a schematic of the SI cycle. A literature review was presented along with materials selected, such as refractory metals, reactive metals, superalloys, glassy metals, ceramics, cermets, polymers, composites, and coatings. The experimental method was then described. A capsule method was developed to rapidly quantify the decomposition rate of the candidate materials ...

Energy Technology Data Exchange (ETDEWEB)

To obtain Pinus wood-plastic composites, wood samples were impregnated with methyl methacrylate and polymerized by the use of gamma rays from a /sup 60/Co at different dose exposure and total dose. The best percentage of polymerization was obtained with the exposure of 2.0 MR of gamma radiation. It was found that the impregnation and polymerization, determined by the density values along the samples were uniform. The density became 2.6 times higher in relation to the control samples. The storage of the impregnated wood samples showed losses of the monomer, even when wrapped with aluminum or polyethylene film. It is recommended that the wood samples should be irradiated soon after impregnation.

British Library Electronic Table of Contents (United Kingdom)

The factors affecting the rate of silica leaching in alkaline aqueous media from surface silanized, nanoporous, amorphous, silica gels and from silanized silica gels that have been modified with polyamines to form the previously reported silica polyamine composites (SPCs), BP-1 and BP-2 have been investigated. Silanization with alkyl trichlorosilanes slows the rate of silica leaching relative to the unmodified silica gels. The use of bulkier aryl silanes somewhat decreases the silica leaching under the same conditions. Interestingly, after modification of the silanized silica with poly(allylamine) (PAA) to make BP-1, the leaching increases, but subsequent modification of the SPC with chloroacetic acid to make BP-2, quenches this increase. A mechanism explaining these results is discussed. ...

Energy Technology Data Exchange (ETDEWEB)

Polyester WPC (wood-polymer composite) systems are one of the promising materials for multiple uses increasing the mechanical properties, provided that their dimensional stability can be improved. Possibility was pursued for the improvement in the dimensional stability of the polyester WPC systems prepared by electron beam irradiation. The impregnation of the mixture of polyester and monomer into both oven-dried beech veneers and preswollen wood was followed by mutual irradiation process. Polymerization was carried out at total dosage of 6 Mrad to the respective surfaces of samples by an electron beam accelerator, and the reaction was completed by heating at 80 deg C for 24 hr. The dimensions of the samples were measured primarily in the tangential direction, and their dynamic modulus and loss modulus were measured by a Rheovibron DDV-2 and the vibrating reed method. The results and the discussion are given for the reaction mode of ...

British Library Electronic Table of Contents (United Kingdom)

Two types of representative nanometer materials, i.e., fibroid nanometer attapulgite and approximate spherical ultrafine diamond, were selected as fillers of polytetrafluoroethylene (PTFE) to study the mechanism of the wear-reducing actions of the fillers in PTFE composites. The friction and wear tests were performed on a block-on-ring wear tester under dry sliding conditions. Differential scanning calorimetry (DSC) was used to investigate material microstructure and to examine modes of failure. No significant change in coefficient of friction was found, but the wear rate of PTFE composites was orders of magnitude less than that of pure PTFE. DSC analysis revealed that nanometer attapulgite and ultrafine diamond played a heterogeneous nucleation role in PTFE matrix and consequently resulte...

Science.gov (United States)

We presented a simple approach for in-situ synthesis of poly(dimethylsiloxane) (PDMS)-gold nanoparticles composite film based on the special characteristics of PDMS itself. It is an environmentally safe synthesis method without the requirement of additional reducing/stabilizing agents. The region where the resulting gold nanoparticles distribute (in the matrix or on the surface of the polymer) and the size of the nanoparticles, as well as the colour of the free-standing films, can be simply controlled by adjusting the ratio of curing agent and the PDMS monomer. The chemical and optical properties of these composite films were studied. Using such a method, gold nanoparticle micropatterns on PDMS surfaces can be performed. And based on the gold nanoparticles micropattern, further modification with antibodies, antigens, enzymes and other biomolecules can be achieved. To verify this ability, an immobilized glucose oxidase (GOx) ...

Energy Technology Data Exchange (ETDEWEB)

Desorption behavior of pyrene, phenanthrene and naphthalene from fullerene, single-walled carbon nanotubes (SWCNTs) and multi-walled carbon nanotubes (MWCNTs) was examined. Available adsorption space of carbon nanotubes (CNTs) was found to be the cylindrical external surface, neither the inner cavities nor inter-wall spaces due to impurities in the CNTs and restricted spaces (0.335 nm) of the MWCNTs, respectively. Desorption hysteresis was observed for fullerene but not for CNTs. Deformation-rearrangement was proposed to explain the hysteresis of polycyclic aromatic hydrocarbons (PAHs) for fullerene, due to the formation of closed interstitial spaces in spherical fullerene aggregates. However, long, cylindrical carbon nanotubes could not form such closed interstitial spaces in their aggregates due to their length, thus showing no significant hysteresis. High adsorption capacity and reversible adsorption ...

Energy Technology Data Exchange (ETDEWEB)

Lithium metal-polymer electrolyte batteries with improved utilisation of the active material at a moderate-low temperature (65degC) were realised. Low molecular weight poly(ethylene glycol) (PEG, MW=2000) was used as the lithium-ion conductive matrix in the composite cathode. The cathode active material was crystalline V{sub 2}O{sub 5}. A blend of poly(ethylene oxide) (PEO, MW=4x10{sup 6}) and PEG was used as a solid polymer electrolyte (SPE). The transport properties of the SPE were evaluated at various temperatures. A specific conductivity as high as 1.0x10{sup -4} S cm{sup -1} was calculated at 45degC. The temperature dependence of the interfacial resistances between lithium/SPE and cathode material/PEG was evaluated. The lithium/SPE interfacial resistance decreases linearly with the temperature. The charge transfer resistance between cathode material and PEG reaches a minimum at 60degC and it does not decrease with a ...

Energy Technology Data Exchange (ETDEWEB)

Silanization of the silica gel surface in the synthesis of silica gel polyamine composites uses (chloropropyl)-trichlorosilane (CPTCS). It is possible to substitute a molar fraction of reagent CPTCS with methyltrichlorosilane (MTCS), creating a mixed silane surface layer. Two types of silica gels were modified with a series of MTCS:CPTCS molar ratios. Solid-state CP/MAS 29Si and 13C NMR spectroscopies were used to evaluate the surface silane composition. Surface silane coverage was markedly improved for the resulting gels. When polyamines were grafted to the resultant MTCS:CPTCS silane layers, it was shown that the decrease in the number of propyl attachments to the polyamine resulted in increased quantities of ''free amines''. Optimum MTCS:CPTCS ratios were determined for three polyamines grafted onto one silica gel. A substantial free amine increase was observed for poly(allylamine) (PAA). Metal uptake ...

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Allyl alcohol (AA), acrylonitrile (AN), methyl methacrylate (MMA), monomers and monomer mixtures AA+AN, AA+MMA were used to conserve and consolidate Beech and Spruce. After impregnation, copolymerisation and polymerisation were accomplished by gamma irradiation. The fine structure of wood+polymer(copolymer) composites was investigated by Scanning Electron Microscopy (SEM). It was observed that copolymer obtained from AA+MMA monomer mixture showed the optimum compatibility. The compressional strength and Brinell Hardness Numbers determined for untreated and treated wood samples indicated that the mechanical strength of wood+copolymer composites was increased. It was found that the mechanical strength of the wood samples containing the AA+MMA copolymer was higher than the others. In the presence of P(AA/MMA), at highest conversion, the compressive strength perpendicular to the fibres in Beech and Spruce increased ...

International Nuclear Information System (INIS)

Angelin Pedra is a specie found in the north of Mato Grosso State in Brazil, where an expressive volume of waste of this wood is produced. An alternative to recycle this waste is to produce wood plastic composites. However, structural and chemical investigations are fundamental to generate information for this use. In the present work, low field NMR was used to determine the spin-lattice and spin-spin relaxation times with objective to investigate the molecular dynamic behavior of the alburnu and cerne regions of Angelin Pedra aiming at a potential use of this waste wood in polymeric composites. The results of the proton spin-lattice relaxation time (T1H) and the proton spin-spin relaxation time (T2H) showed at least three different mobility domains for both regions. Among the values, one was very flexible and other was rigid. Knowing that wood is a polymer composite basically constituted by cellulose, ...

Energy Technology Data Exchange (ETDEWEB)

Concerning high performance composite solid propellant BAMO and BAMO-based copolymers, synthetic method and properties of them were studied. Comparison graph of theoretical specific impulse for various propellants were shown, by that, reason why highest specific impulse BAMO was selected as direction of the study. As the orientation of synthesis, those were indicated that radicals at both ends should be hydroxyl so as urethane bonding was available, that liquid at normal temperature was required for easy handling, and that glass transition temperature is required to be low enough. Synthesis was conducted by ring-opening polymerization of ring ether detail procedures of which were explained. Measurements of properties was performed for thermochemical properties, thermal decomposition, combution heat, and friction sensitivity test to confirm safety. As the result, those were understood that thermal decomposition was divided into two phases, rapid exothermal ...

Energy Technology Data Exchange (ETDEWEB)

The advent of carbon nanotubes, which are graphite layers convoluted in cylinders several nanometers in diameter and several micrometers in length, as well as the experiments on implanting metal atoms in such tubes open the way to producing nanoconductors and other materials with unique properties. For theorists, the basic challenge is interpreting and predicting the structure and properties of these systems. The linearized augmented-plane-wave method (LAPW) is one of the most accurate methods in the theory of the electronic structure of solids. A generalization of this method for quasi-two-dimensional systems, surface electronic states, and layered crystals is known. The LAPW theory for quasi-unidimensional systems, which exhibit translational symmetry in one direction, has been absent thus far. In this paper, the authors suggest a version of such a theory and use this method to calculate the electronic structure of carbyne (a linear chain of carbon atoms) and ...

Science.gov (United States)

Polymer matrix composites are presently used in many fields due to their excellent mechanical properties such as high specific strength and stiffness. However, not much is known of these composites' response to impact loading, which usually occurs at strain rates much higher than the strain rates used to measure the quasi-static mechanical properties of materials. The use of static properties in the study of structures that undergo dynamic loading can produce excessive design weight or cause unexplained and untimely failure. The studies included in this dissertation provide the results of Split Hopkinson Pressure Bar experiments to determine the ultimate compressive strength and strain of composites at high strain rates. Most researchers are using specimens with different dimensions and geometry. For this reason, it is difficult to compare results of tests done by different people. Herein, the Split ...

British Library Electronic Table of Contents (United Kingdom)

Gas separation membranes with polydimethylsiloxane(PDMS)/polystyrene(PS) were prepared by using the sequential interpenetrating polymer network (IPN) method with various PS contents (10?70wt%). These gas separation membranes can be applied to reduce the smoke density in the emission gas of diesel engines. PS content has a pronounced effect on the membrane performance. It was found that the optimized PS contents in the final membrane were 50wt%. The emission capacities of diesel engines used in this study were 632 cc and 11,149 cc. When the oxygen separation membrane was used in the diesel engines, the smoke density of both diesel engines was remarkably reduced (35?73%). The oxygen concentration in the inlet air affects the composition of the emission gases. Especially, hydrocarbon (HC) dec...

British Library Electronic Table of Contents (United Kingdom)

In situ composites based on poly(ethylene 2,6-naphthalate) (PEN) and a thermotropic liquid crystal polymer (Vectra A950) were prepared by melt blending under different processing conditions. Thermal behaviour, mechanical and physical properties and morphology of the blends were investigated. The DSC analysis indicates that, as expected, Vectra enhances the crystallization process of PEN. Moreover, mechanical and thermal tests evidence the significant role of 20wt% Vectra on increasing the material performances; tensile properties, coupled with SEM, show that strength and modulus of PEN are significantly improved when Vectra domains are long and continuous fibrils. The overall results can be attributed to the compatibilisation of the system induced by the mixing conditions that affect the e...

Energy Technology Data Exchange (ETDEWEB)

The separator can be used for electrical separation of the drilling string used as the channel of communication with transmission of face information. It contains upper and lower metal conductors electrically insulated from each other by an insulator made of layered polymer composite material. In order to improve reliability of the connection of the conductors to the insulator and reduce the metal consumption on the ends of the conductors that come into contact with the insulator there are graduated niches with radial projections. The latter form jointly with the layers of the insulator a crown-radial-multiple stage undetachable connection. The niches decreases from the outer diameter of the conductors to the inner. The insulator has additional layers made of high-module fibers of carbon or boron which cover the radial projections in stages.

UK PubMed Central (United Kingdom)

Tubular membrane structures are widespread in eukaryotic cells, but the mechanisms underlying their formation and stability are not well understood. Previous work has focused on tube extrusion from...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Effects of dopant and coating carbon nanotube on anodic performance of Si were studied for metallic anode Li ion rechargeable battery with large capacity. Although the large Li intercalation capacity higher than 1500mAhg{sup -1} is exhibited on pure Si, it decreased drastically with increasing cycle number. Increasing the electrical conductivity by doping Cr or B is effective for increasing the initial capacity and the cycle stability of Si for Li intercalation. Coating semiconductive Si with the carbon nanotube by decomposition of hydrocarbon is effective for increasing the cycle stability, though the initial Li intercalation capacity slightly decreased. Conducting binder is also important for increasing the cycle stability and it was found that Li intercalation capacity higher than 1500mAhg{sup -1} can be sustained by using poly vinyliden fruolide. Consequently, reversible Li intercalation capacity of 1500mAhg{sup -1} was successfully ...

British Library Electronic Table of Contents (United Kingdom)

Multiwall carbon nanotubes (MWCNTs) were functionalized with a photosensitizer, rosebengal (RB), and folicacid (FA), an anti-cancer drug simultaneously and individually, which was characterized with various analytical instruments like Fourier Transform Iinfrared (FTIR) spectroscopy, UV?Vis spectroscopy, Thermogravimetric analysis (TGA), Photoluminescence (PL) spectroscopy, X-ray photoelectron spectroscopy (XPS), and Transmission electron microscopy (TEM). FTIR spectra confirmed the chemical modification of MWCNT. The chemical functionalization of MWCNT with RB was further supported by UV?Vis and PL spectra.

International Nuclear Information System (INIS)

This paper deals with preparation of PE clay nano composite specimen for transmission electron microscopy (TEM) and studying the difference between dispersion of clay in low density polyethylene using poly(hydrogen methyl siloxane) (PHMS) as coupling agent and untreated one. Argon ion milling is the conventional means by which film sections are thinned to electron transparency for TEM analysis, but this technique exhibits significant problems. In particular, selective thinning and imaging of sub-micrometer inclusions during sample milling are highly problematic. We have achieved successful results using the focused ion beam (FIB) lift-out technique, which utilizes a 30 kV Ga"+ ion beam to extract electron transparent specimens with nanometer scale precision. Using this procedure, we have prepared a number of thin film materials representing a range of structures and compositions for TEM analysis. We believe that FIB milling will create major ...

Energy Technology Data Exchange (ETDEWEB)

A lightweight, low permeability liner for graphite epoxy composite compressed gas storage vessels. The liner is composed of polymers that may or may not be coated with a thin layer of a low permeability material, such as silver, gold, or aluminum, deposited on a thin polymeric layer or substrate which is formed into a closed bladder using torispherical or near torispherical end caps, with or without bosses therein, about which a high strength to weight material, such as graphite epoxy composite shell, is formed to withstand the storage pressure forces. The polymeric substrate may be laminated on one or both sides with additional layers of polymeric film. The liner may be formed to a desired configuration using a dissolvable mandrel or by inflation techniques and the edges of the film seamed by heat sealing. The liner may be utilized in most any type of gas storage system, and is particularly applicable for hydrogen, gas ...

International Nuclear Information System (INIS)

The conditions of production and the stability regions have been studied for the following crystallohydrates of trisubstituted uranyl orthophosphates: (UO_2)_3(PO_4)_2x6H_2O, (UO_2)_3(PO_4)_2x4H_2O, and (UO_2)_3(PO_4)_2xH_2O. Their thermal stability has been studied. It is shown that thermal dehydration of high-water hydrates at 220-240 deg C gives (UO_2)_3(PO_4)_2xH_2O. The anion composition and crystal structure of the compound remain constant up to 1000 deg C. The mixture of the composition of U_3O_8xU_3(PO_4)_4 is the final product of decomposition at 1000 deg C. The thermodynamic constants of dehydration processes have been calculated. A conclusion has been made about the polymer structure of the compound in which water is located between the uranylphosphate layers.

Energy Technology Data Exchange (ETDEWEB)

The polymer industry is a young industry that has undergone tremendous growth and change over the last sixty years. Many important discoveries in polymer science have been accidental. Most of the learning has been by trial and error and most of the understanding is still basically empirical--make a polymer material or compound and then put it to the test to study what it is and how it performs. This article provides an overview of what polymers and polymer compounds are, why they behave as they do, and it discusses several examples of failures of rubber and plastic components.

Science.gov (United States)

... Title : Wear Rate and Friction Coefficient in Liquid Nitrogen and Hydrogen of Steel Sliding on Polymer Laminates (Various Fabrics and Polymers. ...

UK PubMed Central (United Kingdom)

Synthetic polymers and nanomaterials display selective phenotypic effects in cells and in the body that affect signal transduction mechanisms involved in inflammation, differentiation, proliferation,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Functionalization of carbon nanotubes is very challenging for their applications. The paper here describes a new method to functionalize multi-walled carbon nanotubes (MWCNTs) as specific affinity adsorbents. MWCNTs were acid purified and pretreated with (3-aminopropyl)-triethoxysilane (APTES) in order to introduce abundant amino groups on the surface of MWCNTs. After the conversion of amino groups to carboxyl groups by succinic acid anhydride, MWCNTs were attached to protein A or aminodextran using 1-ethyl-3,3' (dimethylamion)-propylcarbodiimide as a biofunctional crosslinker. The incorporation of aminodextran as a spacer arm noticeably increased the binding capacity of the APTES-modified MWCNTs for protein A. The application of affinity MWCNTs for purification of immunoglobulin G was then evaluated. The affinity of MWCNTs with AMD spacer exhibited a high adsorption capacity of {approx}361 {mu}g IgG/mg MWCNT (wet basis). About 75% of ...

Energy Technology Data Exchange (ETDEWEB)

A quantitative description is proposed for the depletion-induced slip thickness and velocity profile of a polymer solution near the wall-fluid interface in simple shear flow. The inhomogeneous polymer density profile at a flat wall is inserted into the equations of motion for the flow of a polymer solution near the flat wall. The theory is in quantitative agreement with simulation results. (letter to the editor)

International Nuclear Information System (INIS)

... compounds polymers polyolefins polyvinyls radiation effects SYNTHESIS.

Energy Technology Data Exchange (ETDEWEB)

The goal of this research project by the Energy & Environmental Research Center (EERC) was to determine the potential for coal ash to serve as a {open_quote}functional filler{close_quotes} in plastics and other composite materials, with special emphasis on recycled plastics. The term functional filler is intended to indicate that the material added to the plastic does more than take up space and extend the use of the polymer. Determining the functional filler potential of ash was not the only intent of this project, since another prime objective was to find a use for materials currently considered waste. The term functional filler also opened a door to the use of cenospheres, which are currently marketed and for which there is sufficient market demand that they do not fit the category of a waste even though they are a product of coal combustion. Cenospheres, hollow spherical ash particles, were selected because of their unique properties. ...

Energy Technology Data Exchange (ETDEWEB)

porous silica ceramics were prepared(with HCL catalyst)using H{sub 2}O/TEOS molar ratios of 2.6-59.0, with the EtOH/TEOS ratio fixed. After preparing 9 kinds of sol, the followings were investigated; measurement of the gelation time, thermal analyses by TG/DTA, property analyses of the intermediates by FT-IR and X-ray diffractometry with dried samples, analyses of SiO{sub 2} polymer by FT-IR, the investigation of specific surface area and pore size distribution by N{sub 2}-adsorption isotherm, and structural change of SiO{sub 2} polymer and pore morphology by TEM observation, with samples heat-treated to 500 deg. C. In the concentrations of investigated compositions and catalyst, gelation time showed a minimum at ca. 11 moles of water per one mole of TEOS, the highest degree of polymerization at ca.8-18 moles, and the largest specific surface area at ca. 11 moles, which means that the polymerization proceeded fastest at ca. ...

International Nuclear Information System (INIS)

Radiation technology offers a very wide scope for utilisation and commercial exploitation in various field. All over the world, this technology is being favourably considered for different applications like radiation sterilisation of medical products, preservation of food by controlling the physiological processes for extending shelf-life and eradication of microbial and insect pests, radiation processing of polymeric materials and treatment of sewage sludge. Bangladesh Atomic Energy Commission has taken radiation processing programmes in a big way right from its inception. This paper describes the studies carried out by various research groups in Bangladesh Atomic Energy Commission mainly using Cobalt-60 gamma radiation. The investigation covers medical sterilisation, food preservation and development and modification of polymeric materials by gamma radiation. Both food preservation and radiation sterilisation of medical products are now being commercially carried out in the Gammatech ...

British Library Electronic Table of Contents (United Kingdom)

Solid-phase extraction and gas chromatography with electron-capture detection has been used for sensitive, simple, and reliable analysis of carfentrazone-ethyl residues in water. Carfentrazone-ethyl was enriched by use of multiwalled carbon nanotubes (MWCNT), a new adsorptive material. Several conditions affecting recovery of the analyte, for example polarity and volume of eluents, pH of water samples, and sample volume, were studied. Recovery from fortified samples, linear range, and limit of detection were evaluated. The results showed that MWCNT are an efficient SPE adsorbent for preconcentration of carfentrazone-ethyl in water. Under the optimized SPE conditions, recovery of carfentrazone-ethyl from fortified water was 81.49?91.08%, with RSD from 1.66 to 8.21%. The limits of detection ...

British Library Electronic Table of Contents (United Kingdom)

We demonstrate a novel cross-sectional deformation, called the radial corrugation, of multi-walled carbon nanotubes (MWNTs) under hydrostatic pressure. Theoretical analyses based on the continuum elastic approximation have revealed that MWNTs consisting of more than ten concentric walls undergo elastic deformations at critical pressure Formula Not Shown , above which the circular shape of the cross-section becomes radially corrugated. Various corrugation modes have been observed by tuning the innermost tube diameter and the number of constituent walls, which is a direct consequence of the core-shell structure of MWNTs. Cross-sectional views of MWNT under high hydrostatic pressure: elliptic deformation with the mode index n = 2 (left), and radial corrugations with n = 5 (center), and n = 6 ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Dispersions of single-walled carbon nanotubes (SWNTs) in various surfactant solutions have been systematically evaluated as additives in MEEKC. The compounds examined were catechins, phenolic acids, and flavonoids. Compared with zwitterionic and neutral surfactants, the addition of anionic dispersion seemed to be better at separating the three types of analytes in microemulsion system. In order to achieve low operating currents, an in situ-synthesized surfactant system based on the combination of a long-chain alkyl acid with an organic base was used in MEEKC. The optimized buffer contained 0.5% (57-mM) ethyl acetate, 0.6% (30-mM) lauric acid, 4.0% (666-mM) propanol, 50-mM Tris solution, and 4.5-mg/L the dispersion of SWNTs. Under optimized conditions, the established method was ap...

International Nuclear Information System (INIS)

The effects of intradot electron-electron interaction on the photon-assisted Andreev tunneling of a superconductor/carbon-nanotube/superconductor system are studied by using nonequilibrium Green's function technique. The inverse supercurrent reflecting the #pi#-junction transition emerges in the spin-split energy-levels regime polarized by the Coulomb interaction. For the positive tunneling case, the supercurrent reaches its maximum when the spin-degenerate energy-levels are nearest to the Fermi surface. Conversely, for the negative tunneling case, the supercurrent reaches its maximum when two split energy-levels are symmetric with respect of the Fermi surface. The sign and the amplitude of the Andreev tunneling depend distinctly on the energy-level spacing tuned by photon-assisted tunneling. In order to fully understand the transport characteristics, the current-carrying density of states are investigated, which clearly shows the enhancement, suppression or even ...

Energy Technology Data Exchange (ETDEWEB)

Molar excess volumes, V{sup E}, molar excess enthalpies, H{sup E}, and speeds of sound data, u, of chloroform (i) + aniline or o-toluidine (j) binary mixtures have been measured as a function of composition at 308.15 K. Isentropic compressibility changes of mixing, {kappa}{sub S}{sup E} have been determined by employing speed of sound data. Topological investigations of V{sup E} data reveals that aniline, chloroform and o-toluidine are associated entities and these (i + j) mixtures contain a 1:1 molecular complex. The IR studies lend further support to the nature and extent of interaction for the proposed molecular entity in the mixtures. H{sup E} and {kappa}{sub S}{sup E} values have also been calculated by employing Moelwyn-Huggins concept [Polymer 12 (1971) 387] taking topology of the constituents of the mixtures. It has been observed that calculated H{sup E} and {kappa}{sub S}{sup E} values compare well with their corresponding experimental ...

Energy Technology Data Exchange (ETDEWEB)

A review of the various solidification agents and techniques that are currently available or potentially applicable for the solidification of low-level radioactive wastes is presented. An overview of the types and quantities of low-level wastes produced is presented. Descriptions of waste form matrix materials, the wastes types for which they have been or may be applied and available information concerning relevant waste form properties and characteristics follow. Also included are descriptions of the processing techniques themselves with an emphasis on those operating parameters which impact upon waste form properties. The solidification agents considered in this survey include: hydraulic cements, thermoplastic materials, thermosetting polymers, glasses, synthetic minerals and composite materials. This survey is part of a program supported by the United States Department of Energy's Low-Level Waste Management Program (LLWMP). This ...

Energy Technology Data Exchange (ETDEWEB)

This project has received DOE support since July 1, 1978. During this period, 40 papers have been published dealing predominantly with chlorophyll-photosensitized electron transfer reactions in a variety of media (solutions, polymer films, lipid bilayer membranes). The overall theme of this work has been to develop mechanistic strategies f or photochemical energy storage via chlorophyll, using the green plant photosynthetic system as a paradigm for designing in vitro systems. Microheterogeneous lipid vesicle suspensions allow ready application of time-resolved optical spectroscopy to follow the course of light-induced electron transfer processes. Both the yields and the lifetimes of electron transfer products were markedly improved in the vesicle systems. In subsequent studies, this compartmentalization was favorably manipulated by controlling the electrical charge on the membrane surface, by controlling the solubility properties of the acceptors, by varying the ...

International Nuclear Information System (INIS)

Particularly high coherence of the x-ray beam is associated, on the ID19 beamline at ESRF, with the small angular size of the source as seen from a point of the sample (0.1-1 #mu#rad). This feature makes the imaging of phase objects extremely simple, by using a 'propagation' technique. The physical principle involved is Fresnel diffraction. Phase imaging is being simultaneously developed as a technique and used as a tool to investigate light natural or artificial materials introducing phase variations across the transmitted x-ray beam. They include polymers, wood, crystals, alloys, composites or ceramics, exhibiting inclusions, holes, cracks, ... . 'Tomographic' three-dimensional reconstruction can be performed with a filtered back-projection algorithm either on the images processed as in attenuation tomography, or on the phase maps retrieved from the images with a reconstruction procedure similar to that used for electron microscopy. The ...

International Nuclear Information System (INIS)

Novel hybrid organic/inorganic nanocomposites made of metal oxide and conjugated polymer nanocomposite and its application in bulk-heterojunction solar cells were studied. The composite was composed of different concentrations of strontium titanate (SrTiO_3) and polyaniline doped phosphoric acid. The optimum concentration of strontium titanate was found to be 0.2 v/v. An inorganic-organic photovoltaic device with a structure of Ag/Pani-H_3PO_4-SrTiO_3/Al has been fabricated. The ideality factor value of the diode was found to be 1.8. This n value of the diode implies a deviation from ideal junction behaviour. The barrier height #phi#_b value for the diode was found to be 0.56 eV. The Ag/Pani-H_3PO_4-SrTiO_3/Al diode shows a photovoltaic behaviour with a maximum open-circuit voltage V_o_c of 2.49 V, and short-circuit current I_s_c of 5.6 mA under light illumination #lambda# = 460 nm. The conversion efficiency was found to be 5.2%. It is ...

International Nuclear Information System (INIS)

The process of miniemulsification allows the generation of small, homogeneous, and stable droplets containing monomer or polymer precursors and magnetite which are then transferred by polymer reactions to the final polymer latexes, keeping their particular identity without serious exchange kinetics involved. It is shown that the miniemulsion process can excellently be used for the formulation of polymer-coated magnetic nanoparticles which can further be used for biomedical applications. The use of high shear, appropriate surfactants, and the addition of a hydrophobe in order to suppress the influence of Ostwald ripening are key factors for the formation of the small and stable droplets in miniemulsion and will be discussed. Two different approaches based on miniemulsion processes for the encapsulation of magnetite into polymer particles will be presented in detail.

Wastenet

...Polymer Fuel Cells Challenge Publications News Events Login Register Search Content type All Web pages Case studies Publications News Video Home ...Buildings Carbon capture & storage Combined heat & power Electricity transmission & distribution Energy storage Fuel cells Geothermal Hydroelectric Hydrogen Industry Lighting Marine Metering Nuclear Solar Transport Wind ...Home Emerging technologies Current focus areas Polymer Fuel Cell Challenge Polymer Fuel Cells Challenge The objective of the Polymer Fuel Cells Challenge is to develop,...prove and commercialise novel polymer fuel cell technologies that have the potential to deliver a step-change in overall system cost. What are ...

Energy Technology Data Exchange (ETDEWEB)

The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metal alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy ...

Energy Technology Data Exchange (ETDEWEB)

In many ways, the Advanced Industrial Materials (AIM) Program underwent a major transformation in Fiscal Year 1995 and these changes have continued to the present. When the Program was established in 1990 as the Advanced Industrial Concepts (AIC) Materials Program, the mission was to conduct applied research and development to bring materials and processing technologies from the knowledge derived from basic research to the maturity required for the end use sectors for commercialization. In 1995, the Office of Industrial Technologies (OIT) made radical changes in structure and procedures. All technology development was directed toward the seven ``Vision Industries`` that use about 80% of industrial energy and generated about 90% of industrial wastes. The mission of AIM has, therefore, changed to ``Support development and commercialization of new or improved materials to improve productivity, product quality, and energy efficiency in the major process industries.`` Though AIM remains ...

UK PubMed Central (United Kingdom)

The main aim of the present study was to evaluate potential of ternary complexation (comprising of drug, cyclodextrin and polymer) as an approach for taste masking. For this purpose famotidine with...Full Text Available

UK PubMed Central (United Kingdom)

A variety of albumin polymers were prepared and tested for binding with hepatitis B surface antigen (HBsAg): synthetic polymers cross-linked by either glutaraldehyde or carbodiimide; heat-aggregated...Full Text Available

Science.gov (United States)

The present article studies the electret state of polymers when moving through an alternating-current corona discharge plasma and investigates means for the determination of the transition of the polymeric material from the initial state of the electret when the corona-displaying voltage is increased.

Science.gov (United States)

Commercial introduction of new polymer materials for use as the electrolyte in solid tantalum and solid aluminum electrolytic capacitors is underway. ...

Science.gov (United States)

Demand for compact instrumentation, portable field equipment, and new electromagnetic weapons is

Energy Technology Data Exchange (ETDEWEB)

The chemistries of reactants, plasticizers, solvents and additives in an epoxy paint are discussed. Polyamide additives may play an important role in the absorption of molecular iodine by epoxy paints. It is recommended that the unsaturation of the polyamide additive in the epoxy cure be determined. Experimental studies of water absorption by epoxy resins are discussed. These studies show that absorption can disrupt hydrogen bonds among segments of the polymers and cause swelling of the polymer. The water absorption increases the diffusion coefficient of water within the polymer. Permanent damage to the polymer can result if water causes hydrolysis of ether linkages. Water desorption studies are recommended to ascertain how water absorption affects epoxy paint.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

FEP polyethylene mechanical properties affected by UV. " Siloxane-modified materials resist AO. " Nonsilicone polymers attacked by AO ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents ionic conductivity results obtained with polymer electrolytes and also with propylene carbonate solutions. The domain of electrochemical activity of this salt has been determined using cycle volt-amperometry in propylene carbonate. Preliminary experiments on the stability of the polymer electrolyte with respect to the lithium electrode have been carried out for a possible subsequent use in lithium batteries. (J.S.) 4 refs.

Energy Technology Data Exchange (ETDEWEB)

Threshold pump intensity values leading to irreversible damage to colored laser elements based on elastic polymers were measured. The damage to colored elastomers is connected with absorbing microinclusions but is independent of molecular absorption. It is shown that damage to the elastomers has a pronounced threshold character in contrast to the microdamage accumulation effect in glassy polymers. The damage threshold for elastomers is 1.5 times higher, which is connected with the absence of microstresses (characteristics for organic glasses) in the specimens. 13 references.

Energy Technology Data Exchange (ETDEWEB)

Ultra-thin, uniform, pinhole-free solid polymer electrolyte films having a fixed carboxylic ester group of approximately 1 {mu}m thickness were prepared by polymerization of methyl acrylate and tris(2-methoxyethoxy)vinylsilane in a glow discharge plasma. The carboxylic ester group of the plasma polymer were transformed to lithium carboxylate groups by treatment with lithium iodide. This process give a single lithium ion conductive film. These solid polymer electrolyte films showed ionic conductivities of the order of 10{sup -8} S cm{sup -1} (10{sup 4} {omega} cm{sup 2} resistance per unit area) at room temperature. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Thin, lightweight, and flexible gas-diffusion electrodes (GDEs) based on freestanding entangled networks of single-walled carbon nanotubes (SWNTs) decorated with Ag nanoparticles (AgNPs) are tested as the air-breathing cathode in a zinc-air battery. The SWNT networks provide a highly porous surface for active oxygen absorption and diffusion. The high conductivity of SWNTs coupled with the catalytic activity of AgNPs for oxygen reduction leads to an improvement in the performance of the zinc-air cell. By modulating the pH value and the reaction time, different sizes of AgNPs are decorated uniformly on the SWNTs, as revealed by transmission electron microscopy and powder X-ray diffraction. AgNPs with sizes of 3-5 nm double the capacity and specific energy of a zinc-air battery as compared with bare SWNTs. The simplified, lightweight architecture shows significant advantages over conventional carbon-based GDEs in terms of weight, thickness and conductivity, and hence ...

Science.gov (United States)

Understanding the influence of interfacial structures on the nanoarchitecture mechanical properties is of particular importance for its mechanical applications. Due to a small size of constituting nanostructural units and a consequently high volume ratio of such interfacial regions, this question becomes crucial for the overall mechanical performance. Boron nitride bamboo-like nanotubes, called hereafter boron nitride nanobamboos (BNNBs), are composed of short BN nanotubular segments with specific interfaces at the bamboo-shaped joints. In this work, the mechanical properties of such structures are investigated by using direct in situ transmission electron microscopy tensile tests and molecular dynamics simulations. The mechanical properties and deformation behaviors are correlated with the interfacial structure under atomic resolution, and a geometry strengthening effect is clearly demonstrated. Due to the interlocked joint interfacial structures and compressive ...

Energy Technology Data Exchange (ETDEWEB)

Polymers containing hydroquinone, catechol or their corresponding benzoquinones are a special class of redox polymers. Three pathways of their syntheses are possible: condensation polymerization of suitable monomers, addition polymerization of vinyl monomers containing redox moiety, and chemical attachment of redox unit onto pre-made polymeric matrix. A range of functionalized matrices have been employed such as polyethers, polyesters, polycarbonates, polyurethanes, polyamides and others. Protection of their phenolic functionality has conducted to chemically interesting redox polymer precursors. The presence of a redox moiety coupled with the extant functionalization of the polymer matrix makes the materials very valuable, of wide properties and consequently of vast applicability. For instance, in the oil field, some polymers such as carboxy-methyl-cellulose (CMC) are often applied ...

International Science & Technology Center (ISTC)

Metal Matrix Composites on the Basis of Nano-Materials

International Science & Technology Center (ISTC)

Development of the Method of Electrodepositing Nanostructured Composite Coatings with Improved Engineering Properties

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behavior of the anti-thalassemia and anti-HIV replication drug, deferiprone, was investigated on a carbon nanotube-modified glassy carbon (GC-CNT) electrode in phosphate buffer solution, pH 7.40 (PBS). During oxidation of deferiprone, two irreversible anodic peaks, with E{sub 1}{sup 0}=452 and E{sub 2}{sup 0}=906mV, appeared, using GC-CNT. Cyclic voltammetric study indicated that the oxidation process is irreversible and diffusion controlled. The number of exchanged electrons in the electro-oxidation process was obtained, and the data indicated that deferiprone is oxidized via two two-electron steps. The results revealed that carbon nanotube (CNT) promotes the rate of oxidation by increasing the peak current, so that deferiprone is oxidized at lower potentials, which thermodynamically is more favorable. This result was confirmed by impedance measurements. The diffusion coefficient, electron-transfer coefficient and ...

International Nuclear Information System (INIS)

Complimentary spectroscopic, microscopic and electrochemical studies were performed to characterise the barrier properties as well as the interface structure of model iron substrates covered with thin plasma polymer films. Cathodic plasma polymers were deposited which show high barrier properties. The metal surface was pre-treated by a reducing or oxidising plasma. This allowed the adjustment of the oxidation state of the interface layer. The interface structure was characterised by means of X-ray photoelectron sputter profiles, infrared spectroscopy and the application of a Kelvin probe. The investigations show that the measured Voltapotential on the plasma polymer surface can be correlated with the oxidation state of the interface. Reducing plasmas lead to an almost oxide free surface. After deposition of the plasma polymer, this reduced state of the oxide is sensitive to re-oxidation of the interface ...

International Nuclear Information System (INIS)

The paper generalizes some results of the United States/Moldova program on advanced composite organic and semiconductor light emitters. High density exciton system bound to N impurity superlattice grown by modern technologies and GaP:N, GaP:N:Sm nanocrystals distributed in transparent fluorine-containing polymers will be used as the base elements for new generation of optoelectronic devices. The work seeks to expand further the applications of GaP itself through the formation of nanocomposites. Classic and new methods are applied for preparation of GaP:N nanoparticles with the controlled dimensions developed clear quantum confinement effect. The long-term ordered bulk GaP crystals as well as their nanoparticles have been investigated by TEM, XRD, Raman scattering, and luminescent methods. The evolution of the Raman Light Scattering and luminescence spectra is reported from pure and doped GaP single crystals grown over 40 years ago and evaluated ...

Energy Technology Data Exchange (ETDEWEB)

The preparation and performance of membranes for application to hydrogen separation from coal-derived gas is described. The membrane material investigated was dense amorphous silica deposited on a suitable support by chemical vapor deposition (CVD). Two types of support materials were pursued. One type consisted of a two-layer composite, zeolite silicalite/{alpha}-Al{sub 2}O{sub 3}, in the form of tubes approximately 0.7 cm in diameter. The other type was porous glass tubes of diameter below 0.2 cm. The first type of support was prepared starting from {alpha}-Al{sub 2}O{sub 3} tubes of 1{micro}m mean pore diameter and growing by hydrothermal reaction a zeolite silicalite layer inside the pores of the alumina at the OD side. After calcination to remove the organic template used in the hydrothermal reaction, CVD was carried out to deposit the final silica layer. CVD was carried out by alternating exposure of the surface with silicon tetrachloride and water vapor. SEM ...

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to passivation-free solid-state rechargeable batteries composed of Li.sub.4 Ti.sub.5 O.sub.12 anode, a solid polymer electrolyte and a high voltage cathode. The solid polymer electrolyte comprises a polymer host, such as polyacrylonitrile, poly(vinyl chloride), poly(vinyl sulfone), and poly(vinylidene fluoride), plasticized by a solution of a Li salt in an organic solvent. The high voltage cathode includes LiMn.sub.2 O.sub.4, LiCoO.sub.2, LiNiO.sub.2 and LiV.sub.2 O.sub.5 and their derivatives.

Energy Technology Data Exchange (ETDEWEB)

Researchers are developing polymer-based coating systems to reduce scaling and corrosion of air-cooled condensers that use a geothermal fluid spray for heat transfer augmentation. These coating systems act as barriers to corrosion to protect aluminum fins and steel tubing; they are formulated to resist the strong attachment of scale. Field tests have been done to determine the corrosion and scaling issues related to brine spraying and a promising organometallic polymer has been evaluated in salt spray tests.

Science.gov (United States)

Systems MEMS sensors C11-20 Lifetime Distributions of Aluminum Electrolytic Capacitors C11-22 Adhesion Strength of Advanced Polymer Films for Flexible and Rigid...

Science.gov (United States)

[12] Kusy, R. P. and Turner, D. T.: Influence of molecular-weight ofpoly(methyl methacrylate)on fracture morphology in notched tension, Polymer. ...

International Nuclear Information System (INIS)

A kind of polymer-metal complex gel electrolyte is successfully prepared and is used in dye-sensitized solar cells. Raman and X-ray photoelectron spectroscopy confirm the structure of this complex and is found that the metal ion reacts with nitrogen in the polymer. This novel electrolyte shows apparent diffusion coefficient of iodide of 8.37 x 10-7 cm2 s-1 and the energy conversion efficiency of 6.10% when the amount of ZnI2 is 0.04 M. By studying the dissociation active energy of the inorganic salt in electrolytes, we find that the metal salts can dissociate more easily after reacting with polymer and as a result can provide extra free iodide ion. The cell maintains ca. 93% of its initial efficiency after 20 d without further sealing, which shows good long-time stability.

Science.gov (United States)

... Accession Number : ADD014577. Title : Phthalonitrile Monomers Containing Imide and/or Phenoxy Linkages, and Polymers Thereof. ...

Energy Technology Data Exchange (ETDEWEB)

The development of 'Green Chemistry' requires new materials to replace the conventional organic chemistry by biological catalysts, to produce fine chemicals in an environmentally friendly manner. Microbial whole cells can be directly used as biocatalysts, providing a simple and cheap methodology since enzyme isolation and purification are avoided. High-density polyethylene (HDPE) is a very stable polymer though it can be activated by gamma radiation to induce grafting. Glycidyl methacrylate was grafted onto macroporous HDPE and PP in the range of 1-6%, proportional to the initial monomer concentration. Grafted polymers were further chemically modified with ethylenediamine to generate a cationic hydrogel of micron-size thickness onto the internal polymer surfaces. Modified polymers were able to immobilize Gram-positive and Gram-negative bacteria that can catalyze a chemical reaction as ...

International Nuclear Information System (INIS)

Portuguese 1998 p. 47 Brazil Silva, Edemilson P. Universidade Federal,

Science.gov (United States)

Light Weight Composite Mirrors for Science Instruments. Composite Optics, Inc. San Diego, CA. INNOVATION. Light weight, large aperture reflectors of graphite ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Norwegian Open Research Archives (NORA)

Full Text Available

Science.gov (United States)

Not Available

Science.gov (United States)

... at the end of this report. A. Low-Velocity Impact of Composite Sandwich Panels In 2007, the PI developed analytical solutions ...

Energy Technology Data Exchange (ETDEWEB)

MINEQL is a subroutine package to calculate equilibrium composition of an aqueous system, accounting for mass transfer.

Science.gov (United States)

... Abstract : High temperature testing of graphite/epoxy laminates and composite sandwich panels was performed while the Shuttle was on orbit to ...

Science.gov (United States)

the progressive simplification of composite sandwich panels. The equations ... The thermal and structural behavior of composite sandwich panels with a ...

Science.gov (United States)

... Accession Number : ADD808679. Title : Advanced Composites for Aerospace Require Waterjet Technology. Descriptive Note : Journal article. ...

International Nuclear Information System (INIS)

Esters of dihydric alcohols with alkenylphosphonic or alkenylphosphinic acids which are polymerizable by free radicals are described. They are combined with polymer binders, in particular water-soluble polymers, and photoinitiators forming free radicals to give photopolymerizable mixtures which are suitable for the production of photoresists and printing plates. The mixtures display low heat-sensitivity and have long shelf lives. (author) 1 tab.

Energy Technology Data Exchange (ETDEWEB)

Water transport in the ionomeric membrane, typically Nafion{reg_sign}, has profound influence on the performance of the polymer electrolyte fuel cell, in terms of internal resistance and overall water balance. In this work, high resolution neutron imaging of the Nafion{reg_sign} membrane is presented in order to measure water content and through-plane gradients in situ under disparate temperature and humidification conditions.

Energy Technology Data Exchange (ETDEWEB)

We have measured, by {sup 1}H and {sup 13}C nuclear magnetic resonance (NMR), the percent deuteration, the tacticity and the purity of several polymers and one solvent used in the preparation of microcellular foams. The percent deuteration was measured for polystyrene, polyacrylonitrile and polyethylene. The tacticities of polystyrene and polyacrylonitrile were determined. The purity and degradation products of polyacrylonitrile and maleic anhydride were examined. This report documents the experimental procedures and results of these measurements.

British Library Electronic Table of Contents (United Kingdom)

The interaction between molecules and solid surfaces plays important roles in various applications, including catalysis, sensors, nanoelectronics, and solar cells. Surprisingly, a full understanding of molecule-surface interaction at the quantum mechanical level has not been achieved even for very simple molecules, such as water. In this mini-review, we report recent progresses and current status of studies on interaction between representative molecules and surfaces. Taking water/metal, DNA bases/carbon nanotube, and organic dye molecule/oxide as examples, we focus on the understanding on the microstructure, electronic property, and electron-ion dynamics involved in these systems obtained from first-principles quantum mechanical calculations. We find that a quantum mechanical description ...

International Nuclear Information System (INIS)

A stable chlorobenzene dispersion of conducting polyaniline (PANI) has been obtained by doping emeraldine base with dodecylbenzene sulfonic acid (DBSA) and studied by spectrophotometric measurements in the UV-vis-IR range. The electrical properties of PANI: DBSA films obtained from the above dispersion have been investigated under different temperature and relative humidity conditions. All-organic chemoresistive devices have been developed by spin-coating the PANI: DBSA dispersion on flexible substrates, and then by depositing electrodes on the top, from a carbon nanotube conducting ink. Sensing tests performed under exposition to calibrated amounts of ammonia reveal that these simple and inexpensive sensors are able to detect ammonia at room temperature in a reliable way, with a sensitivity linearly related to concentration in the range between 5 ppm and 70 ppm.

Science.gov (United States)

The kinetics of electrical breakdown of thin (15-70 ?m) layers of polymers and ceramics in a constant-sign field at 77-480 K has been investigated. The temperature dependences of the longevity (breakdown waiting time) of both dielectrics have been found to be similar to each other. At elevated temperatures, the longevity of the dielectrics varies exponentially with increasing temperature, and at reduced temperatures, it is temperature-independent (there is an athermal plateau). The mechanisms of elementary events controlling the process of preparation of the dielectrics for breakdown at elevated and reduced temperatures are the thermal-fluctuation over-barrier electron transition from trap to trap and the tunneling (under-barrier) transition, respectively. The hopping electron transport in the field direction gives rise to critical space charges causing breakdown of the dielectrics. The transition barrier heights (trap depths) have been determined. The ...

Science.gov (United States)

We study the emission zone in a single-layer polymer light-emitting diode. The emission zone is found by studying the angular distribution of the electroluminescence. The emission is modeled by accounting for optical interference. We account for birefringence of the anode layer in our model. The active polymer was, however, found to be isotropic. The anode consists of a single-layer of the conducting polymer complex poly(3,4-ethylenedioxythiophene) and poly(styrene sulfonate) (PEDOT-PSS), with enhanced conductivity. As a cathode we use plain aluminum. By using only PEDOT-PSS we avoid having a thin metal layer or indium-tin-oxide as the anode in the path of the escaping light. The active material is a substituted polythiophene with excellent film forming properties. A comparison between the experimental and calculated angular distribution of light emission from a single-layered polymer light-emitting ...

British Library Electronic Table of Contents (United Kingdom)

The effect of particle/matrix interface debonding on composites consisting of elastic particles and viscoelastic matrix is studied. The interface debonding is represented by a nonlinear cohesive law for the high explosive PBX 9501. The Mori-Tanaka method gives the constitutive relation of the composite in terms of the properties of elastic particles, viscoelastic matrix, and nonlinear cohesive law for interfaces. For the example of a composite with spherical particles subject to hydrostatic tension, simple analytical expressions of the composite stress-strain relation are obtained. The strain rate and temperature have strong effects on the composite behavior. High strain rate and low temperature give high strength of the composite. However, the rate and temperature effects decrease as the ...

Science.gov (United States)

The commercial solid phase microextraction (SPME) fibers are not stable enough in organic solvent and tend to swell and strip off from the silica fiber in the high performance liquid chromatography (HPLC) mobile phase, and therefore the application of SPME coupled online with HPLC is limited. In this study, an SPME fiber coated with single walled carbon nanotubes (SWCNTs), prepared by means of electrophoretic deposition, was coupled on line to HPLC for the determination of four endocrine-disrupting compounds, i.e. bisphenol A (BPA), estrone (E(1)), 17?-ethynylestradiol (EE(2)) and octylphenol (OP), in aqueous samples. The results showed that the SWCNTs coating on the prepared fiber did not swell and strip off from the platinum fiber throughout the experiment, thus indicating a high resistance to the HPLC mobile phase, the mixture of water and acetonitrile. The SWCNTs fiber had similar (for OP) or higher (for BPA, EE(2) and E(1)) extraction efficiencies than the ...

Energy Technology Data Exchange (ETDEWEB)

This process for the preparation of nonaqueous dispersions of water-soluble polymerisates concerns compounds obtained by polymerization of water-soluble unsaturated ethylenic monomers in an emulsion of water in oil. The product is then dewatered to a maximum residual water content of 5% by means of microwaves. The process is azeotropic. The polymer has a molecular weight between 100,000 and 50,000,000, preferably between one and 10 million. Before treating with microwaves, the mixture is concentrated by conventional means until it has a polymer concentration between 20 and 65%, preferably between 40 and 60%. The microwaves have a wavelength between 0.1 and 30 cm. These polymer dispersions can be used in drilling fluids and as additives in tertiary oil recovery. 4 claims.

British Library Electronic Table of Contents (United Kingdom)

Nanocapsules coated by medicinal plants have many applications in drug manufacturing. Medicinal plants can be loaded on nanocapsules with polyesteric triblock copolymer poly ethylene glycol-poly butylene adipate-poly ethylene glycol (PEG-PBA-PEG) as shell and olive oil can be introduced as a core of nanocapsules by a method known as polymer deposition solvent evaporation method. In this research, first, certain amount of polymer, Matricaria recutita extract and olive oil were mixed with acetone and then, water was added to the solution using magnetic stirrer. After which the acetone was removed by vacuuming and finally nanocapsules were found by freezing-drier. The study showed the size of nanocapsules depends on variety of factors such as the ratio of polymer to oil and concentration of p...

CERN Document Server

We discuss theoretically and numerically the intramolecular form factor $F(q)$ in dense polymer systems. Following Flory's ideality hypothesis, chains in the melt adopt Gaussian configurations and their form factor is supposed to be given by Debye's formula. At striking variance to this, we obtain noticeable (up to 20%) non-monotonic deviations which can be traced back to the incompressibility of dense polymer solutions beyond a local scale. The Kratky plot ($q^2F(q)$ {\\it vs.} wavevector $q$) does not exhibit the plateau expected for Gaussian chains in the intermediate $q$-range. One rather finds a significant decrease according to the correction $\\delta(F^{-1}(q)) = q^3/32\\rho$ that only depends on the concentration $\\rho$ of the solution, but neither on the persistence length or the interaction strength.

Energy Technology Data Exchange (ETDEWEB)

The performance of different polymers used to flocculate red mud particulate materials in the Bayer process can be evaluated on the basis of their efficiency to achieve adequate settling velocities and turbidity levels. In this study, three commercially available flocculants are evaluated under typical conditions found in the last washer of a Bayer plant. The different shear levels are produced by using a modified Couette flow system. Great differences are noticed in the performance of the polymers when they are compared at different dosages and at different shear rate levels. The data collected also suggests that conventional cylinder settling tests may not be adequate to measure the performance of certain types of polymers. (author)

Energy Technology Data Exchange (ETDEWEB)

We demonstrate control and improvement of charge injection in organic electronic devices by utilizing self-assembled monolayers (SAMs) to manipulate the Schottky energy barrier between a metal electrode and the organic electronic material. Hole injection from Cu electrodes into the electroluminescent conjugated polymer poly[2-methoxy,5-(2{sup {prime}}-ethyl-hexyloxy)-1,4-phenylene vinylene] was varied by using two conjugated-thiol based SAMs. The chemically modified electrodes were incorporated in organic diode structures and changes in the metal/polymer Schottky energy barriers and current{endash}voltage characteristics were measured. Decreasing (increasing) the Schottky energy barrier improves (degrades) charge injection into the polymer. {copyright} {ital 1997 American Institute of Physics.}

International Nuclear Information System (INIS)

In this work, a water-soluble polymer, polyethylenimine (PEI) was used for the simultaneous separation and preconcentration of trace Cu and Mn prior to their determination by flame atomic absorption spectrometry. For this purpose, the sample and the PEI solution were mixed and the metal-bound polymer was precipitated by adding acetone. The precipitate was separated and dissolved in a minimum amounts of water and aspirated into a flame AAS. By increasing the ratio of the volumes of sample to water used in dissolving the precipitate, the analyte elements were concentrated as needed. The sorption is quantitative in the pH ?6. Detection limits were 5.2 ?g/L for Cu and 5.4 ?g/L for Mn. This method is simple, fast and precise.

British Library Electronic Table of Contents (United Kingdom)

A tobermorite/hydroxyapatite composite was prepared by hydrothermal treatment using diatomaceous earth, ?-tricalcium phosphate and slaked lime starting materials. The XRD patterns of the composite confirmed that tobermorite and hydroxyapatite were formed after the hydrothermal process. The bending strength of the composite reached a level higher than 9?MPa after the hydrothermal process. The development of the bending strength was due to the formation of tobermorite and hydroxyapatite during the hydrothermal process. The composite had a high specific surface area due to these newly formed crystals.