International Nuclear Information System (INIS)

Molybdenum oxide nanostructures were synthesized utilizing the solution combustion method where the ammonium molybdate powder and an organic additive were used as precursors. Different organic additives including ethylene diamine tetra-acetic acid (EDTA), polyethylene glycol 200 (PEG 200), sorbitol and urea were used as surfactants in order to investigate the effect of additive structure on morphology and particle size of products. Also various reaction parameters such as the additive/Mo molar ratio, concentration of metal ion in solution, pH of the reaction, and temperature of the synthesis media were changed to study effects on product morphology and size. Outcomes were characterized by Scanning Electron Microscopy (SEM), X-ray diffraction, and Transmission Electron Microscopy (TEM) techniques. Results show a variety of MoO_3 nanoparticles and nanorods produced within the size range of 10-80 nm. Furthermore, microrods and ...

International Nuclear Information System (INIS)

This paper presents the effect of precursor powder size on the thermoelectric properties of sintered nanostructured bulk materials. The transport properties of the nanostructured bulk show a dramatic size effect. There are a lower thermal and electrical conductivity for the bulk with smaller nanopowders. The dimensionless figure-of merit values (ZT) of almost all the samples are much lower than those of the list reported data in the paper because the decrease in the thermal conductivity is counteracted by the reduction in the electrical conductivity and the Seebeck coefficient. The combination route of hydro/solvothermal synthesis and spark-plasma-sintering method provide a well controlled way to significantly reduce the thermal conductivity.

Science.gov (United States)

Robert A. Martock. Cleveland State University, Cleveland, Ohio. Synthesis and Structural Characterization of a. Novel Indium Mercapto Derivative. [Clln(SCH. 2 ...

International Nuclear Information System (INIS)

A mass separated focused ion beam (FIB) is a very useful tool to fabricate nanostructures by writing implantation within an ion beam synthesis process. In these investigations the IMSA-OrsayPhysics FIB, equipped with a Co_3_6Nd_6_4 alloy liquid metal ion source, was applied. Si(100) and (111) wafers were implanted with 60 keV Co"+"+ ions in the dose range of 2 . 10"1"6 to 2 . 10"1"7 cm"-"2. Implantation parameters were investigated, like pixel dwell time, relaxation time (time between two cycles), dose rate as well as the pixel overlapping factor. The subsequent annealing was done in a two step process, namely 600 deg. C for 60 min and 1000 deg. C for 30 min in a N_2 ambient. The results obtained by SEM investigations in terms of continuous nanowire structures following the direction and interrupted CoSi_2 pattern in the direction show a clear dependence on the time scale as well as the scanning mode of the irradiation. Structure sizes as ...

UK PubMed Central (United Kingdom)

This work describes the synthesis and characterization of novel thermoresponsive highly-branched polyamidoamine-polyethylene glycol-poly (D, L-lactide) (PAMAM-PEG-PDLLA) core-shell nanoparticles....Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

A single plasma process involving three consecutive steps has been developed for producing high gas flow catalytic nanostructures on the electrodes of proton exchange membrane (PEM) fuel cells (FC). Using a high density helicon radio frequency (13.56 MHz) plasma, nickel is sputtered onto a porous carbon support. Changing the background gas from argon to methane/hydrogen allowed 2 ?m long, 37 nm diameter carbon nanofibres (CNFs) to be grown by diffusion through the nickel clusters in a 'tip growth' mechanism at the relatively low temperature of 400 deg. C. The third step involves plasma sputtering of platinum onto the CNFs, resulting in nanoclusters (3-8 nm) being formed on the periphery of the CNFs. Four FC cathodes were synthesized on carbon paper and PTFE/carbon loaded cloth (known as gas diffusion layer, GDL), both with and without CNFs, with the Pt/CNFs nanostructures grown on PTFE/carbon loaded cloth having the best FC performances. ...

British Library Electronic Table of Contents (United Kingdom)

A fully lamellar ferrite/cementite nanostructure was designed in a low C steel by using a specific thermal treatment. The strengthening of such microstructure has been investigated as a function of prestrain by rolling up to a deformation of 300%. As in usual pearlitic structure, its work-hardening shows no saturation and its elongation to fracture remains rather constant instead of decreasing drastically as conventional steels. The hardening by a similitude effect is thus not the privilege of pearlitic steels. Nevertheless, its lower initial work-hardening rate at low strain compared to an equivalent pearlitic steel and a lower hardening potential at high strain let us suspect major differences in the nature and the behaviour of ferrite channels in relation to the morphogenesis of the mic...

Energy Technology Data Exchange (ETDEWEB)

We demonstrate the rapid optical characterization of large numbers of individual metal nanoparticles freely diffusing in colloidal solution by confocal laser spectroscopy. We find that hollow gold nanospheres and solid silver nanoparticles linked with a bifunctional ligand, both designed nanostructures, exhibit significantly higher monodispersity in their Rayleigh and Raman scattering response than randomly aggregated gold and silver nanoparticles. We show that measurements of rotational diffusion timescales allow sizing of particles significantly more reliably than can be obtained using translational diffusion timescales.

UK PubMed Central (United Kingdom)

Hyaluronan (HA), a non-sulfated glycosaminoglycan, is widely used in the clinic for viscosurgery, viscosupplementation, and treatment of osteoarthritis. Four decades of chemical modification...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

CERN Document Server

material, and that these magnetic properties vary systematically with the diameter of the spherical pores within the films. A new oscillation effect has been observed for the coercivity of macroporous Ni sub 8 sub 0 Fe sub 2 sub 0 film with different pore layer thickness. sphere templates, the resulting films show well-formed, regular, two- and three-dimensional macroporous networks consisting of spherical pores arranged in a highly ordered face centred cubic (fee) structure. The spherical voids are interconnected by a series of smaller windows that form an open porous structure embedded in the material framework. The diameter of the spherical pores can be precisely changed over the range from 200 to 1000 nm by changing the diameter of the latex spheres used to form the templates. The resulting macroporous material structures are robust, self-supported, dense, polycrystalline, uniform and free from filling defects and contamination or problems caused by shrinkage during processing. The ...

International Nuclear Information System (INIS)

The influence of chemical composition and heat treatment on a low-carbon steel, chromium steel and high speed steel has been examined by polarisation curves and electrochemical parameters deduced from the Tafel plots. The electrochemical corrosion resistance, which is small between the as-received steels become greater after heat treatment, following the order: carbon steel < chromium steel #approx# high speed steel. To explain these differences, the nano- and microstructure of the steels has been characterized by the ex situ techniques of atomic force microscopy and optical microscopy, before and after surface etching with Nital (a solution of 5% HNO_3 in ethanol). This causes preferential attack of the ferrite phases showing the carbide phases more clearly. From these nanostructural studies it was possible to better understand why the passive films formed on chromium steel and high speed steel have superior protective properties to those ...

International Nuclear Information System (INIS)

In the present work the hydrogen desorption properties of nanostructured magnesium hydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM) of elemental Mg powder under hydrogen are investigated. A profound effect of the particle size of synthesized MgH2 hydride on its hydrogen desorption characteristics measured by differential scanning calorimetery (DSC) has been found. All synthesized MgH2 powders are characterized by a double hydrogen desorption peak. Furthermore, below a certain threshold particle size the DSC desorption temperature of the peak doublet starts decreasing rapidly with decreasing of the mean hydride powder particle size (expressed as equivalent circle diameter-ECD). In contrast, the nanograin (crystallite) size of MgH2 does not seem to have apparent effect on the DSC desorption temperature. It is also observed that for powder particles smaller than some threshold value, X-ray diffraction shows the presence ...

UK PubMed Central (United Kingdom)

The endogenous reverse transcriptase reaction of equine infectious anemia virus (EIAV) has been studied, and conditions allowing synthesis of full-length minus-strand DNA have been determined. In contrast...Full Text Available

International Nuclear Information System (INIS)

[3,5-"3H] 4-Azidoclonidine 6 was prepared from [3,5-"3H] 4-aminoclonidine 4 and has emerged as a valuable tool to study the alpha-2-adrenergic receptor. (author)

UK PubMed Central (United Kingdom)

We have synthesized a novel stable precursor, saligenin phosphorotrichloridate, which, on reaction with N-monobiotinyldiamines, generates a series of biotinylated covalent inhibitors of serine esterases....Full Text Available

UK PubMed Central (United Kingdom)

The changes in protein species synthesized during early Drosophila embryogenesis were characterized by two-dimensional electrophoresis. Of the 261 proteins scored, 68 (26%) show dramatic changes in...Full Text Available

Science.gov (United States)

Synthesis and Structural Characterization of a Novel Indium Mercapto Derivative [Clln(SCH2(CO)O)2]2-[(4-MepyH)2]2+. AUTHOR(S): ...

Science.gov (United States)

The synthesis and structural characterization of a novel In(III) complex is described. The reaction between InCl3 with sodium mercapto-acetic acid, (NaSCH2(CO)OH) in 4-methylpyridine, (CH3(C5H5N), (4-Mepy)) at 25 C affords (ClIn(SCH2(CO)O)2)2- ((4-MepyH)2...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

... Abstract only 1063-7869 v. 44(10) CLASSICAL AND QUANTUM MECHANICS,

British Library Electronic Table of Contents (United Kingdom)

The light-emitting properties of cubic silicon carbide films grown by vacuum vapor phase epitaxy on Si(100) and Si(111) substrates under conditions of decreased growth temperatures (T gr ? 900?700?C) have been discussed. Structural investigations have revealed a nanocrystalline structure and, simultaneously, a homogeneity of the phase composition of the grown 3C-SiC films. Photoluminescence spectra of these structures under excitation of the electronic subsystem by a helium-cadmium laser (?excit = 325 nm) are characterized by a rather intense luminescence band with the maximum shifted toward the ultraviolet (?3 eV) region of the spectral range. It has been found that the integral curve of photoluminescence at low temperatures of measurements is split into a set of Lorentzian components. Th...

UK PubMed Central (United Kingdom)

A mixed copper complex with deprotonated nalidixic acid (nal) and histamine (hsm) was synthesized and characterized by FTIR, UV-Vis, elemental analysis, and conductivity. The crystal structure of [Cu(hsm)(nal)H₂O]Cl·3H₂O...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Recent research has shown that biologically inspired approaches to materials synthesis and self-assembly, hold promise of unprecedented atomic level control of structure and interfaces. In particular, the use of organic molecules to control the production of inorganic technological materials has the potential for controlling grain structure to enhance material strength; controlling facet expression for enhanced catalytic activity; and controlling the shape of nanostructured materials to optimize optical, electrical and magnetic properties. In this work, we use organic molecules to modify silver crystal shapes towards understanding the metal-organic interactions that lead to nanoparticle shape control. Using in situ electrochemical AFM (EC-AFM) as an in situ probe, we study the influence of a cationic surfactant cetyltrimethylamminobromide (CTAB) on Ag growth during electrochemical deposition on Ag(100). The results show that the organic ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of this study is fabrication and characterization of silver nanofluid by the submerged arc nanoparticle synthesis system (SANSS). The silver metal electrodes under the electrical discharge will melt and evaporate rapidly and condense to form the nanoparticles in the lower temperature dielectric liquid and produce the suspended nanoparticle. The results showed that the spherical nanosilver particle formed in the ethylene glycol and the mean particle size is about 12.5 nm. The prepared silver nanofluid was irradiated under the 410 nm visible light, electrons could be excited from the valence band to the conduction band. The silver nanofluid more closely resembles Newtonian fluids.

UK PubMed Central (United Kingdom)

In the body, vascular cells continuously interact with tissues that possess nanostructured surface features due to the presence of proteins (such as collagen and elastin) embedded in the vascular wall....Full Text Available

International Nuclear Information System (INIS)

Inorganic nanoparticles are indispensable for science and technology as materials, pigments and cosmetics products. Improving the dispersion stability of nanoparticles in various liquids is essential for those applications. In this review, we discuss why it is difficult to control the stability of nanoparticles in liquids. We also overview the role of surface interaction between nanoparticles in their dispersion and characterization, e.g. by colloid probe atomic force microscopy (CP-AFM). Two types of surface modification concepts, post-synthesis and in situ modification, were investigated in many previous studies. Here, we focus on post-synthesis modification using adsorption of various kinds of polymer dispersants and surfactants on the particle surface, as well as surface chemical reactions of silane coupling agents. We discuss CP-AFM as a technique to analyze the surface interaction between nanoparticles and the effect ...

Energy Technology Data Exchange (ETDEWEB)

Porous nanostructured LiFePO{sub 4} powder with a narrow particle size distribution (100-300nm) for high rate lithium-ion battery cathode application was obtained using an ethanol based sol-gel route employing lauric acid as a surfactant. The synthesized LiFePO{sub 4} powders comprised of agglomerates of crystallites <65nm in diameter exhibiting a specific surface area ranging from 8m{sup 2}g{sup -1} to 36m{sup 2}g{sup -1} depending on the absence or presence of the surfactant. The LiFePO{sub 4} obtained using lauric acid resulted in a specific capacity of 123mAhg{sup -1} and 157mAhg{sup -1} at discharge rates of 10C and 1C with less than 0.08% fade per cycle, respectively. Structural and microstructural characterization were performed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) with energy dispersive X-ray (EDX) analysis while electronic conductivity and ...

British Library Electronic Table of Contents (United Kingdom)

We describe a simple one-pot thermal decomposition method for the production of a stable colloidal suspension of narrowly dispersed superparamagnetic Fe3O4-Ag core-shell nanostructures. These biocompatible nanostructures are highly toxic to microorganisms. Antimicrobial activity studies were carried out on both Gram negative (Escherichia coli and Proteus vulgaris) and Gram positive (Bacillus megaterium and Staphylococcus aureus) bacterial strains. Efforts have been made to understand the underlying molecular mechanism of such antibacterial actions. The effect of the core-shell nanostructures on Gram negative strains was found to be better than that observed for silver nanoparticles. The minimum inhibitory concentration (MIC) values of these nanostructures were found to be considerably lowe...

International Nuclear Information System (INIS)

A few metal complexes of isatin-isonicotinoylhydrazone with Ni(II), Cr(III), Co(II), Cu(II), Zn(II) and Cd(II) have been prepared and characterized on the basis of elemental analyses, infrared and electronic spectra as well as "1H NMR spectra, conductivity and magnetic measurements. In view of the results obtained, it has been found that two molecules of isatin-isonicotinoylhydrazone are chelated to the central metal ion as bis-uninegative ONO tridentate ligand forming non-electrolytic octahedral metal complexes. (author)

International Nuclear Information System (INIS)

The layer-by-layer (LBL) self-assembly has been extensively used as a simple and effective method for the preparation of polyelectrolyte multilayer films. In this work, we utilized this unique method to prepare polyimide precursor/layered double hydroxide (LDH) ultrathin films. Well-crystallized Co-Al-CO_3 LDH and subsequent anion exchanged Co-Al-NO_3 LDH were prepared and characterized by scanning electron microscopy and X-ray diffraction (XRD). By vigorous shaking of the as-prepared Co-Al-NO_3 LDH, positively charged and exfoliated LDH nanosheets were obtained. Atomic force microscopy and XRD investigations indicated the delamination of LDH nanosheets. The precursor of polyimide, poly(amic acid) tertiary amine salt (PAS) was prepared by the polycondensation of dianhydride and diamine, and subsequent amine salt formation. By using the LBL method, heterogeneous ultrathin films of PAS and LDH were prepared. The formation of the ordered ...

UK PubMed Central (United Kingdom)

The use of 2-pyridinealdoxime (paoH)/N,N′-donor ligand (L-L) “blend” in cobalt chemistry has afforded two cationic mononuclear cobalt(III) complexes of the general type [Co(pao)₂(L-L)]⁺,...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

A new bimetallic complex [HNEt3][Cuq2IEu(hfac)3] (q^- = 8-hydroxyquinolinato, hfac^- = hexafluoroacetylacetonate) was prepared simply with only one step and characterized. Upon excitation of the organic ligand q^-, the sensitized europium luminescence was achieved.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

British Library Electronic Table of Contents (United Kingdom)

With collaboration between chemistry, X-ray crystallography, and molecular modeling, we designed and synthesized a series of novel piperazine sulfonamide BACE1 inhibitors. Iterative exploration of the non-prime side and S2prime sub-pocket of the enzyme culminated in identification of an analog that potently lowers peripheral Ab40 in transgenic mice with a single subcutaneous dose.

UK PubMed Central (United Kingdom)

The complete nucleotide sequence of the cap3A gene of Streptococcus pneumoniae, which is directly responsible for the transformation of some unencapsulated, serotype 3 mutants to the encapsulated phenotype,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In this work it is made a study of the structure and electric properties of chlorate polyethylene (PE-CI) with double and simple bonds obtained by continuous plasma with resistive coupling to 13.5 MHz. The synthesis conditions are power between 10 and 14 W and pressure of (6-7) x 10{sup -2} Torr. The synthesized PE-Cl in that way is soluble in acetone what indicates that probably is formed of short chains and not it shows the generalized inter crossing that is presented in some syntheses by plasma and that it can degrade the electric properties of these polymers. The IR and XPS analysis show the vibration of the C-C, C=C and C-CI bonds. The morphology of the polymer after being dissolved shows a compact and flat configuration. The electric conductivity has an approximately lineal behavior in an interval of 35 to 90% of relative humidity. (Author)

Energy Technology Data Exchange (ETDEWEB)

Development of useful high-critical-temperature (high-{Tc}) superconductors requires synthesis of superconducting compounds; fabrication of wires, tapes, and films from these compounds; production of composite structures that incorporate stabilizers or insulators; and design and testing of efficient components. This report describes technical progress of research and development efforts aimed at producing superconducting components based on the Y-Ba-Cu, Bi-Sr-Ca-Cu, Bi-Pb-Sr-Ca-Cu, and Tl-Ba-Ca-Cu oxides systems. Topics discussed are synthesis and heat treatment of high-{Tc} superconductors, formation of monolithic and composite wires and tapes, superconductor/metal connectors, characterization of structures and superconducting and mechanical properties, and fabrication and properties of thin films. Collaborations with industry and academia are also documented. 10 figs.

Science.gov (United States)

... R OFFICIAL FILE COPY SYNTHESIS OF PERFLUOROALIPHATIC ETHER MONOMERS PCR, Inc. ... Synthesis of Perfluoroaliphatic Ether Monomers ...

Energy Technology Data Exchange (ETDEWEB)

After pioneering work in the 1980s, plasma-based ion implantation (PBII) and plasma-based ion implantation and deposition (PBIID) can now be considered mature technologies for surface modification and thin film deposition. This review starts by looking at the historical development and recalling the basic ideas of PBII. Advantages and disadvantages are compared to conventional ion beam implantation and physical vapor deposition for PBII and PBIID, respectively, followed by a summary of the physics of sheath dynamics, plasma and pulse specifications, plasma diagnostics, and process modeling. The review moves on to technology considerations for plasma sources and process reactors. PBII surface modification and PBIID coatings are applied in a wide range of situations. They include the by-now traditional tribological applications of reducing wear and corrosion through the formation of hard, tough, smooth, low-friction and chemically inert phases and coatings, e.g. for engine components. ...

International Nuclear Information System (INIS)

Low pressure silane plasmas are known for their ability to synthesize silicon nanoparticles via gas phase nucleation. While in the past this particle formation has often been considered from the viewpoint of a contamination problem in semiconductor processing, we here describe a silane low pressure plasma that enables the synthesis of highly oriented, cubic-shaped silicon nanocrystals with a rather monodisperse size distribution. These silicon nanocubes have successfully been used in the manufacture of single nanoparticle vertical transistors. We discuss the advantages of this new paradigm of building nanoelectronic devices. The plasma synthesis process is characterized in more detail than in prior work. The particle nucleation, growth and shape evolution are studied. Results indicate that the process provides two spatially distinct zones: a diffuse plasma for particle growth and a constricted plasma zone for particle ...

Energy Technology Data Exchange (ETDEWEB)

The synthesis, characterization, and emission properties of a series of Pt(L{sub 2})(S-S) complexes are reported. The (L{sub 2}) ligands include 4,7-diphenyl-1,10-phenanthroline (Ph{sub 2}phen), 4,4{prime}-dimethyl-2,2{prime}-bipyridine (Me{sub 2}bpy), 1,5-cyclo-octadiene (COD), trimethyl phosphite (P(OMe){sub 3}), and the {alpha}-C-deprotonated form of 2-phenylpyridine (2-phpy). The (S-S) ligands include 1-(tert-butoxycarbonyl)-1-cyanoethylene-2,2-dithiolate (tbcda), 1-(diethoxyphosphinyl)-1-cyanoethylene-2,2-dithiolate (cpdt), cis-1,2-dicarbomethoxyethylene-1,2-dithiolate (met), and N,N-diethyldithio-carbamate (Et{sub 2}dtc). The complexes are readily synthesized by the addition of the dithiolate or thiolate ligand to Pt(L{sub 2})Cl{sub 2} except for Pt(P(OMe){sub 3}){sub 2}(met), which is prepared by the addition of 2 equiv of trimethyl phosphite to Pt(COD)(met).

International Nuclear Information System (INIS)

Fine ceramic particles of zirconia toughened alumina (ZTA), titania toughened alumina (TTA), and zirconia-titania toughened alumina (ZTTA) have been synthesized by ultrasonic spray pyrolysis (USP) at various temperatures from starting salt solutions of various compositions aiming for the development of catalytic material. These particles were characterized for properties such as shape, size and size distribution, diffraction pattern, and chemical and phase composition of elements by scanning electron microscopy (SEM), particle size analyzer (PSA), x-ray diffraction (XRD), and inductively coupled plasma-atomic emission spectroscopy (ICP-AES). Chemical compositions and sizes of ceramic composites have been controlled by the stoichiometry of salt solutions and the flow rate of spraying solutions. The optimum experimental conditions for the various composite particle synthesis have been proposed.

Energy Technology Data Exchange (ETDEWEB)

The synthesis of [3, 3-D[sub 2

Energy Technology Data Exchange (ETDEWEB)

This was a project to investigate the crystal chemistry of OH and H{sub 2}O substitution in silicate minerals by use of X-ray and neutron diffraction methods combined with IR spectroscopy and to interpret and generalize the results using an electrostatic model for these mineral structures. Using these data together with published H position data electrostatic parameters for H sites were calculated from a simple electrostatic model. The data were then used to refine the model for incorporation of H into the wadsleyite structure. This has led to recent work on the synthesis and characterization of hydrous wadsleyites.

Science.gov (United States)

Some acylhydrazine derived ONO donor Schiff bases and their Co(II) and Ni(II) complexes have been prepared having the same metal ion (cation) but different anions. These synthesized metal(II) complexes have been characterized on the basis of their elemental analyses, magnetic moment, molar conductance, and IR and electronic spectral data. All of the Schiff base ligands function as tridentates and the deprotonated enolic form is preferred for coordination. In order to evaluate the effect of anions on the bactericidal activity, these synthesized complexes, in comparison to the uncomplexed Schiff bases have been screened against bacterial species., Escherichia coli, Staphylococcus aureus and Pseudomonas aeruginosa and the results are reported. PMID:18475936

Energy Technology Data Exchange (ETDEWEB)

This paper deals with the preparation and characterization of polyaniline/TiO{sub 2} composite by XRD, UV-VIS spectra, TGA/DTA and FTIR. The composite is used as a cathode material for rechargeable battery comprising of zinc container as the anode, cellulose acetate as the separator and polyvinyl sulfate and carboxy methyl cellulose as the solid polymer electrolytes (SPE). By using the PAn/TiO{sub 2} composite as the cathode material, the cylindrical AA type rechargeable battery was fabricated and the following output was observed. The open circuit voltage (OCV) is 1.4 V and current is 250 mA to 1.0 A, 50 recharge cycles, power density is 350 A h/kg and power efficiency is 70%.

Science.gov (United States)

We have obtained convincing evidence for localization of the optical electron on a single-ring fragment of a chelated bipyridine-like'' ligand (ie., pyridylpyrazine or 4-Methyl-bipyridine). In addition we have completed studies of Ru(bipyrazine){sub 3}{sup 2+} in aqueous sulfuric acid (0--98% by weight) and find clear evidence for sequential addition of six-protons to the six peripheral nitrogen atoms. Studies of zeolite-entrapped complexes are continuing and a series of homo- and heteroleptic complexes have been prepared and characterized. Finally, the synthesis of zeolite-entrapped metallophthalocyanines has now been developed and the copper and cobalt analogues synthesized. The characterization of these materials is now in progress.

International Nuclear Information System (INIS)

Single-crystalline nanostructures often exhibit gradients of surface (and/or interface) curvature that emerge from fabrication and growth processes or from thermal fluctuations. Thus, the system-inherent capillary force can initiate morphological transformations during further processing steps or during operation at elevated temperature. Therefore and because of the ongoing miniaturization of functional structures which causes a general rise in surface-to-volume ratios, solid-state capillary phenomena will become increasingly important: On the one hand diffusion-mediated capillary processes can be of practical use in view of non-conventional nanostructure fabrication methods based on self-organization mechanisms, on the other hand they can destroy the integrity of nanostructures which can go along with the failure of functionality. Additionally, capillarity-induced shape transformations are effected and can thereby be ...

UK PubMed Central (United Kingdom)

The effect of low concentrations of nalidixic acid on ribonucleic acid (RNA) synthesis in Escherichia coli was examined. It was observed that RNA synthesis in exponentially growing...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This article considers the fundamentals of what happens in asolid when it is impacted with a medium energy gallium ion. The study ofthe ion/sample interaction at the nanometer scale is applicable to mostfocused ion beam (FIB) based work even if the FIB/sample interaction isonly a step in the process, e.g., micromachining or microelectronicdevice processing. Whereas the objective in other articles in this issueis to use the FIB tool to characterize a material or to machine a deviceor transmission electron microscopy (TEM) sample, the goal of the FIB inthis article is to have the FIB/sample interaction itself become theproduct. To that end, the FIB/sample interaction is considered in threecategories according to geometry: below, at, and above the surface.First, the FIB ions can penetrate the top atom layer(s) and interactbelow the surface. Ion implantation and ion damage on flat surfaces havebeen comprehensively examined; however, FIB applications require thefurther ...

Energy Technology Data Exchange (ETDEWEB)

Novel complexes of the type (Pt(DACH)(N-R-iminodiacetate)), wherein DACH represents (R,S)- and (R,R)-1,2 diaminocyclohexane and R represents /minus/Me, /minus/EtOH, and /minus/CH/sub 2/Ph groups, have been prepared, purified, and characterized by spectroscopic techniques (/sup 1/H, /sup 13/C, and /sup 195/Pt NMR;MS(FAB);IR) and by the measurement of selected physical properties (pH, pK/sub a/, conductivity, and molecular weights). The data are consistent with the formation of two diastereomeric complexes in unequal proportions in which the N-R-iminodiacetate ligand appears to be bonded as a pseudofacial tridentate chelate. One are of the ligand forms a stable five-membered-ring O,N-chelate while the other arm appears to be involved in ion-pair formation (zwitterion-like) involving the carboxylate anion and the formally positive Pt(II) central metal atom. It has been demonstrated indirectly that an active impurity was present in predictably inactive bulk complexes ...

British Library Electronic Table of Contents (United Kingdom)

Synthesis of highly anisotropic rod-like b-Si3N4 particles with different morphological characteristics was accomplished using commercial a-Si3N4. A number of powder mixtures were prepared with additions of various oxides (Al2O3+RE2O3, being RE=Y, La or Yb) that were subsequently heat treated in a loose powder state in the temperature range of 1750-1950degreeC and dwell times from 10 to 180min under high pressure of N2 (60MPa) in a hot isostatic press. The obtained aggregated porous bodies were lightly crushed by hand using an alumina mortar and pestle and subsequently subjected to sequential chemical treatments to eliminate the glassy phases and possible residual crystalline compounds, and to separate the synthesized b-Si3N4 particles. Resulting b-Si3N4 particles were characterized by X-r...

Science.gov (United States)

PMID:21370327

Science.gov (United States)

No abstract prepared.

UK PubMed Central (United Kingdom)

Skin protects the body from pathogens and degradation. Mummified skin in particular is extremely resistant to decomposition. External influences or the action of micro-organisms, however, can degrade...Full Text Available

International Nuclear Information System (INIS)

In this work, the effects of the focus ion beam (FIB) milling process on the optical properties of semiconductor nanostructures were investigated. With this aim, a sensitive materials system based on InGaAs/GaAs quantum dots with well known and excellent optical properties was selected for the FIB treatment. The FIB technique was used to locally remove a metallic mask deposited on top of the quantum dot sample. The photoluminescence (PL) signal, collected from the circular openings, was used to infer the possible damage effects of the ion beam on the properties of the dots.

Energy Technology Data Exchange (ETDEWEB)

This paper presents recent results concerning the chemical and electrochemical synthesis, the electrochemical properties and the characterization of two new families of amorphous oxides of formula Li{sub x}MVO{sub 4} (1

British Library Electronic Table of Contents (United Kingdom)

A novel difunctional acylhydrazone has been synthesized by the reaction of 5-methylisoxazole-4-carboyl hydrazine with benzaldehyde and characterized by X-ray crystallography and spectroscopy. The obtained results demonstrate the crystal belongs to triclinic, space group Formula Not Shown . Moreover, the spectroscopic properties were evaluated through density functional theory (DFT) and time-dependent density functional theory (TD DFT) calculations. The results reveal that UV-Vis absorption peaks at 194, 217.5 and 290.5nm are mainly attributed to (p, p)p*, partly (p, p)p* and partly pp*, and predominantly pp*, respectively, with intraligand charge-transfer transition (ILCT) character. The fluorescence emission peak at 485.96nm should be assigned to ILCT. In addition, the results of antibact...

British Library Electronic Table of Contents (United Kingdom)

In this paper, multilayer oxide nanorods were deposited in the nanopores of anodic aluminum oxide (AAO) via solution infiltration followed by heat treatment. The nanorods have a core-shell structure. First, the shell (nanotube) with the thickness of about 40nm was made of TiO"2 through the hydrolysis of (NH"4)"2TiF"6. Second, silver nanoparticles with the diameter of about 3nm were added into the TiO"2 layer through thermal decomposition of AgNO"3 at elevated temperatures. Then, cylindrical cores (nanorods) of CoO and ZnO with 200nm diameter were prepared, respectively. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the structure and composition of the nanorods. UV-vis light absorption measurements in the wavelength range from 350 to...

Energy Technology Data Exchange (ETDEWEB)

Reduction of silver myristate (AgMy) under mild thermal reaction conditions in a dipolar aprotic solvent i.e. N, N-dimethylformamide (DMF) has been carried out. UV-visible absorption measurements of dried and re-dispersible brown flocculants showed broad features of surface plasmon resonance (SPR) due to silver nanoparticles. The freshly isolated particles showed absorption bands at 414 and 485 nm, respectively, due to inter-particle coupling or clustering of silver ions and silver atoms. X-ray diffraction (XRD) pattern of fcc zero-valent silver resulted in crystallite size of about 10 nm. Scanning electron microscopy (SEM) revealed formation of rod shaped silver with increasing reaction temperature. Thermal analysis (TGA) showed about 10% weight loss due to organic capping.

Energy Technology Data Exchange (ETDEWEB)

Targets for heterogeneous transmutation of americium are composed of a support material, the inert matrix and of an americium oxide compound: AmO{sub 2-x} or Am{sub 2}O{sub 3}. In parallel to the studies using americium, simulated compounds of americium oxide, chosen amongst lanthanide oxides, are used. The selection of these compounds is based on theoretical, physical and crystallochemical considerations. In order to assess the influence of impurities composed of lanthanide oxides, resulting from the separation process, on the physical and chemical properties of such a target, synthesis of oxide powders containing impurities associated with the simulated americium oxide, characterizations, crystallographic studies and sodium compatibility tests have been performed. (author)

British Library Electronic Table of Contents (United Kingdom)

An amphiphilic azobenzene diblock copolymer {2-[4-(4-methoxy phenyl azo)phenoxy]hexyl acrylate co-acrylic acid} was synthesized via reversible addition-fragmentation chain transfer polymerization in a hydrothermal reactor. The products were characterized by 1H-NMR, DSC, GPC and UV-Vis spectroscopy. Different self-assembly behaviors of this amphiphilic diblock copolymer in different organic solvent with different water content were investigated. In THF/H2O solution, the diblock copolymer self-assembled into spheres and the spheres would then change to vesicles with smaller size by increasing the volume of H2O. However, in DMSO/H2O solution, the sizes and morphologies of the self-assembled spheres would not change significantly with an enhanced amount of H2O. Photochromic behaviors of the am...

Energy Technology Data Exchange (ETDEWEB)

Research conducted since the last progress report includes the synthesis and characterization of twenty three novel proton-ionizable crown ether compounds. Metal ion complexation behavior of new and previously-synthesized proton-ionizable crown ether compounds has been probed by solvent extraction and transport across polymer-supported liquid membranes. The behavior of neutral polyether and proton-ionizable polyether ligands in polymeric membrane electrodes has been assessed. Studies of the use of proton-ionizable crown ethers for separation of lithium isotopes were initiated. Also, the thermodynamics of interactions between alkali metal cations and ionized crown ethers have been probed by titration calorimetry. 10 refs., 1 tab.

International Nuclear Information System (INIS)

We report synthesis, characterization and ion transport in polyether-based ionic melt electrolytes consisting of Li salts of low-basicity anions covalently attached to polyether oligomers. Purity of the materials was investigated by HPLC analysis and electrospray ionization mass spectrometry. The highest ionic conductivity of 7.1 x 10-6 S/cm at 30 deg. C was obtained for the sample consisting of a lithium salt of an arylfluorosulfonimide anion attached to a polyether oligomer with an ethyleneoxide (EO) to lithium ratio of 12. The conductivity order of various ionic melts having different polyether chain lengths suggests that at higher EO:Li ratios the conductivity of the electrolytes at room temperature is determined in part by the amount of crystallization of the polyether portion of the ionic melt.

British Library Electronic Table of Contents (United Kingdom)

Abstract Flame retardants (FRs) are used for in protection against fire. Organic inorganic hybrids could become one of the most promising FR solution in the future. In this paper, the synthesis, the characterization and the use as FRs and filler of grafted titania and alumina with 2 chloroethylphosphonic acid are presented. These hybrids contain 3.8 3.24% P and have good flame retardance when they are incorporated into unsaturated polyester resins. Alumina treated with 2 chloroethylphosphonic acid performed better than titania. The advantage of this approach is the use of these hybrid materials as filler and FR, in the same time, and the increase in flame retardancy by synergistic effect between alumina phosphorus and chlorine, for unsaturated polyester resins. Copyright 2010 John Wiley & ...

Energy Technology Data Exchange (ETDEWEB)

The structure and catalytic properties of 2 wt.-% Pd/SiO/sub 2/ catalysts promoted with 2 wt.-% MgO and 0.2-5 wt.-% iron have been investigated. Catalysts were characterized by TPR, hydrogen chemisorption, and Moessbauer spectroscopy and their catalytic performance in methanol formation was also measured. At 16 at.-% iron a sharp maximum was observed in the activity which can be interpreted as being due to simultaneous promotion with iron and MgO. Independent mechanisms of promotion were found for the two modifiers: iron influenced the metallic component by forming bimetallic PdFe particles while MgO changed the properties of silica in a favourable way. 6 figs., 29 refs., 1 tab.

International Nuclear Information System (INIS)

The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples.

Energy Technology Data Exchange (ETDEWEB)

Coal liquefaction investigations required the availability of model compounds for mechanistic investigations. Towards this end, IITRI was funded to develop an approach for the synthesis of one of the target compound. This study was carried out in several phases as outlined here. Initial synthetic investigations on obtaining 2-tetrolol was carried out using high pressure and temperature reduction with Raney nickel catalyst. The next step consisted in incorporation of a hydroxymethyelene group at the C-3 position. This was successfully carried out utilizing 2-tetrolol, formaldehyde, and calcium oxide. An alternate improved method was developed using 3-carboxyl-2-naphthol. This required less time, gave a cheer product in higher yield. Efforts at the introduction of a chloromethylene group only yielded polymeric material or starting material in spite of protection the phenolic group by various groups. They synthesis of 3, 5-dimethyl-6- bromobenzyl ...

Energy Technology Data Exchange (ETDEWEB)

Lithium-ion batteries are now considered to be the technology of choice for future hybrid electric and full electric vehicles to address global warming. LiCoO{sub 2} has been the most widely used cathode material in commercial lithium-ion batteries. Since LiCoO{sub 2} has economic and environmental issues, intensive research has been directed towards the development of alternative low cost, environmentally friendly cathode materials as possible replacement of LiCoO{sub 2}. Among them, spinel LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} material is one of the promising and attractive cathode materials for next generation lithium-ion batteries because of its high voltage (4.7 V), acceptable stability, and good cycling performance. Research advances in high voltage spinel LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} are reviewed in this paper. Developments in synthesis, structural characterization, effect of doping, and effect of coating are presented. In addition to ...

Science.gov (United States)

The purpose of this study was to examine arachidonic acid (AA) metabolism and to characterize the type of adrenergic receptor (AR) involved in the production of the major metabolite of this fatty acid. ({sup 14}C)AA was incubated with GPT-rings and the radiolabelled products were extracted and separated by TLC method. The medium was also assayed for radiolabelled immunoreactive PG's (iPG's) and leukotrienes (LT) B4 and C4 by RIA or Enzyme immunoassay (EIA) after exposure to various AR agonists. ({sup 14}C)AA was incorporated into GPT-rings and metabolized mainly into iPGE2 and smaller amounts into PGF2{alpha}. Trace amounts of PGD2 and 6-keto-PGF1{alpha} but not LTB4 or LTC4 were detected by RIA and/or EIA. Incubation of GPT rings for 15 minutes with isoproterenol and salbutamol resulted in a significant increase of PGE2 synthesis (optimum conc: 10{sup {minus}7}, 10{sup {minus}7}M respectively). In contrast, dobutamine, ...

Energy Technology Data Exchange (ETDEWEB)

X-ray scattering from lyophilized proteins or protein-rich samples is characterized by the presence of two characteristic broad peaks at scattering angles equivalent to momentum transfer values of 0.27 and 0.6 nm{sup -1}, respectively. These peaks arise from the interference of coherently scattered photons. Once the conformation of a protein is changed, these two peaks reflect such change with considerable sensitivity. The present work examines the possibility of characterizing the most common cause of hemolytic anaemia in Egypt and many Mediterranean countries; {beta}-thalassemia, from its X-ray scattering profile. This disease emerges from a genetic defect causing reduced rate in the synthesis of one of the globin chains that make up hemoglobin. As a result, structurally abnormal hemoglobin molecules are formed. In order to detect such molecular disorder, hemoglobin samples of {beta}-thalassemia patients are collected, ...

British Library Electronic Table of Contents (United Kingdom)

A series of thiazolo[3,2-b][1,2,4]triazole incorporating diphenylsulfone moieties were synthesized starting from 5-[4-(4-X-phenylsulfonyl)phenyl]-4H-1,2,4-triazole-3-thioles 3a-c, X=H, Cl, Br. Thus, alkylation of 1,2,4-triazoles 3 with phenacyl bromide or 4-bromophenacyl bromide afforded S-substituted 1,2,4-triazoles 4, 5. These new intermediates 4 and 5, in the presence of H2SO4 (c), were cyclized to 2-[4-(4-X-phenylsulfonyl)phenyl]-6-(4-Y-phenyl)[1,3]thiazolo[3,2-b]-[1, 2,4]-triazoles 6, 7 (I) and not to isomeric thiazolo[2,3-c][1,2,4]-triazoles 6, 7 (II). The newly synthesized compounds were characterized by IR, 1H, 13C NMR and elemental analysis. MS spectra confirmed the formation of thiazolo[3,2-b][1,2,4]triazole 6, 7 (forms I) in detriment of [2,3-c] isomeric compounds (forms II). Th...

British Library Electronic Table of Contents (United Kingdom)

A general approach has been designed to synthesize some mononuclear and binuclear cyclometalated platinum(II) complexes, containing aromatic N-donor ligands with the presence of one Cl- trans to carbon. In this way, cyclometalated platinum(II) complex [Pt(C^N)Cl(dmso)], 1, C^N = N(1),C(2prime)-chelated, deprotonated 2-phenylpyridine and dmso = dimethylsulfoxide, was used as a precursor to react with imidazole derivatives (1-methylimidazole, 2a, imidazole, 2b,), monodentate pyridine derivatives (4-methylpyridine, 2c, pyridine, 2d,) and bidentate pyridine derivative (4,4prime-bipyridine, 3 and 4,). Synthesized complexes were fully characterized by using multinuclear NMR spectroscopy (1H, 13C{1H} and 195Pt), correlation NMR spectroscopy (1H-1H COSY, 13C{1H}-1H Heteronuclear Multiple Quantum C...

Energy Technology Data Exchange (ETDEWEB)

Crystalline MnV{sub 2}O{sub 6} has been synthesized by a polymer gellation method and investigated for its physical and electrochemical properties as an anode material for Li secondary battery. The physical characterization was carried out by thermal analysis (TG/DTA), FT-IR and SEM. Structural analysis by powder XRD and spectroscopic analysis by XANES showed that the synthesized compound is MnV{sub 2}O{sub 6} with brannerite structure. The Li insertion of MnV{sub 2}O{sub 6} anode during the first charge showed a large capacity of about 1400 mAh/g, accompanied by irreversible structural transformation into amorphous material. Despite its structural transformation to amorphous during the first lithiation, subsequent cycles showed a capacity of about 800 mAh/g. This paper presents the advantage of this material over existing anode material and discusses the mechanism underlying the electrode process.

Energy Technology Data Exchange (ETDEWEB)

Abstract: We report for the selective-area chemical synthesis of semiconductor single-crystal organic nanowires of silver-tetracyanoquinodimethane (Ag-TCNQ). Straight and smooth Ag-TCNQ nanowires can be produced and patterned on micrometer and nanometer scale on silicon substrates covered with a thin layer of Ag film through the reaction of TCNQ and Ag in a simple gas-solid chemical reaction process. Ag-TCNQ nanowires are characterized by UV-vis, IR and Raman spectroscopy, respectively. The Ag-TCNQ nanowires grows preferentially along the [100] direction of strong - stacking of Ag-TCNQ molecules. Nanodevices based on these nanowires are fabricated using focus ion beam (FIB) technique. Electrical properties are characterized and I-V hysteresis is observed, which shows memory effect with electrical switching of three orders on-off ratio. These nanowires could be potential for use in optical storage, ultrahigh-density ...

British Library Electronic Table of Contents (United Kingdom)

A variety of platinum(II) complexes of methimazole (2-mercapto-1-methylimidazole; HImS=neutral form and ImS=thiolate form), coordinated in both thione and thiolate forms, have been isolated by reacting methimazole with [PtCl(terpy)]Cl (terpy=2,2prime:6prime,2Prime terpyridine), [PtCl2(bipy)] (bipy=bipyridine), [PtCl2(o-phen)] (o-phen=o-phenanthroline), [PtCl2(CH3CN)2] and [PtCl2(COD)] (COD=1,5-cyclooctadiene). These complexes were characterized by electronic absorption, IR and NMR (1H, 13C, 195Pt) spectroscopies. Molecular structure of [Pt(bipy)(HImS)2]Cl23H2O (3a3H2O) has been established by single crystal X-ray crystallography. Platinum thiolate complex, [Pt(ImS)2(HImS)2] (5), could be obtained by treatment of [Pt(HImS)4]Cl2 with sodium methoxide in methanol. The solution of 5 in organic...

International Nuclear Information System (INIS)

Two sup(99m)Tc complexes of (N-piperidinylethyl) hexamethyl diaminodithiol (NEP-DADT) have shown high brain uptake in rodents and lower primates. One of these sup(99m)Tc complexes has given positive images of the brain in man which are qualitatively related to regional brain blood flow (rCBF). In order to determine the structure of these sup(99m)Tc products, the corresponding "9"9Tc(NEP-DADT) complexes were prepared and characterized by HPLC, TLC, fast-atom-bombardment mass spectrometry (FAB MS) and other analytical techniques. These results indicate that the two "9"9Tc (NEP-DADT) complexes are syn and anti isomers (i.e. one isomer has the N-piperdinylethyl side chain located syn to the technetium oxo core while the other has this side chain located anti to the technetium oxo core). (author).

Energy Technology Data Exchange (ETDEWEB)

Mono-dispersed cubic CeO{sub 2} nanoparticles have been synthesized using a surfactant-assisted method with laurylamine hydrochloride and cerium alkoxide modified with acetylacetone in an aqueous solution system. The prepared cubic CeO{sub 2} nanoparticles had a highly crystallized structure at 353 K and formed rod-like structures by calcination at 673 K after freeze-drying the CeO{sub 2} gel. We discovered a clear potential to make 1D, 2D or 3D CeO{sub 2}-materials with a well-controlled characteristic length and shape by assembling cubic-shaped CeO{sub 2} nanoparticle building blocks. CeO{sub 2}-TiO{sub 2} composite nanostructures have also been synthesized by changing the mole ratio of cerium alkoxide/titanium alkoxides. By utilizing the redox characteristic of CeO{sub 2}, CeO{sub 2} nanoparticles and CeO{sub 2}-TiO{sub 2} composite nanostructures after calcination, showed reaction activity toward the oxidization of I{sup -} to I{sub 2}, due ...

Energy Technology Data Exchange (ETDEWEB)

A single crystalline ternary nanostructure having the formula A.sub.xB.sub.yO.sub.z, wherein x ranges from 0.25 to 24, and y ranges from 1.5 to 40, and wherein A and B are independently selected from the group consisting of Ag, Al, As, Au, B, Ba, Br, Ca, Cd, Ce, Cl, Cm, Co, Cr, Cs, Cu, Dy, Er, Eu, F, Fe, Ga, Gd, Ge, Hf, Ho, I, In, Ir, K, La, Li, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Os, P, Pb, Pd, Pr, Pt, Rb, Re, Rh, Ru, S, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Tc, Te, Ti, Tl, Tm, U, V, W, Y, Yb, and Zn, wherein the nanostructure is at least 95% free of defects and/or dislocations.

British Library Electronic Table of Contents (United Kingdom)

A new method of the synthesis of high molecular polybutylene terephthalate (PBT) is developed with the use of Irganox 1010, tris(nonylphenyl) phosphite and hypophosphite as stabilizers and boron nitride or boron oxide as a catalyst is proposed.

International Nuclear Information System (INIS)

The evolution of metallic substance atomic structure is studied on temperature variation including crystal heating up to melting points, a crystal- liquid phase transition and initiation of a high-density liquid specific structure. It is marked that heat induced changes of simple metal structure can be described as changes around a natural elementary cell which is common for both a crystal and a liquid and consists of a central atom and Z_1 atoms of the first coordination sphere. On this basis the vacancy model of melting is verified. Concentrations of melting vacancies are determined by coordination numbers in the form of Z_1/(1+Z_1)"2 which are the same for both a crystal and a natural elementary cell. The size of natural elementary cells is in an agreement with that of the coordination sphere featured in the liquid and phase transition statistical theory. Calculated data are given for a number of metals, Cs, Eu, Ni, V included

British Library Electronic Table of Contents (United Kingdom)

Modifications of the structure and mechanical properties in LiF crystals irradiated with MeV-energy Au ions have been studied using nanoindentation, atomic force microscopy and optical spectroscopy. The nanostructuring of crystals under a high-fluence irradiation (above 1013 ions/cm2)?was?observed. Nanoindentation tests show a strong ion-induced increase of hardness (up?to 150?200%), which is related to the high volume concentration of complex color centers, defect aggregates, dislocation loops and grain boundaries acting as strong barriers for dislocations. From the?depth profiling of the hardness and energy loss it follows that both nuclear and electronic stopping mechanisms of MeV Au ions contribute to the creation of damage and hardening. Whereas the electronic stopping is dominating i...

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline and nanostructured materials offer unique microstructure-dependent properties that are superior to coarse-grained materials. These materials have been shown to have very high hardness, strength, and wear resistance. However, most current methods of producing nanostructured materials in weapons-relevant materials create powdered metal that must be consolidated into bulk form to be useful. Conventional consolidation methods are not appropriate due to the need to maintain the nanocrystalline structure. This research investigated new ways of creating nanocrystalline material, new methods of consolidating nanocrystalline material, and an analysis of these different methods of creation and consolidation to evaluate their applicability to mesoscale weapons applications where part features are often under 100 {micro}m wide and the material's microstructure must be very small to give homogeneous properties across the feature.

Energy Technology Data Exchange (ETDEWEB)

A number of high voltage cathode materials are now being considered for their ability to increase the energy density of lithium-ion batteries. In this study, a lithium-nickel composite alloy (LiNiVO{sub 4}) was synthesized using a rheological phase reduction method that incorporated mixtures of LiOH-H{sub 2}O, Ni(CH{sub 3}COO){sub 2}, 4H{sub 2}O, NH{sub 4}VO{sub 3} and C{sub 2}H{sub 2}O{sub 4}-2H{sub 2}O. The rheological phase method was used to prepare the compounds from a solid-liquid rheological mixture. Solid reactants were first mixed in a proper molar ratio, and water or solvents were added to the solid-liquid rheological body. X-ray powder diffraction (XRD) and Fourier Transform (FT) analyses were conducted to characterize the powders. Scanning electron microscopy (SEM) was used to characterize the morphological features and particle sizes of the powders. Results of the analyses indicated that the single-phase LiNiVO{sub 4} composite is ...

Energy Technology Data Exchange (ETDEWEB)

The research for the development of flexible organic electronic devices (FEDs) is rapidly increasing worldwide, since FEDs will change radically several aspects of everyday life. Although there has been considerable progress in the area of flexible inorganic devices (a-Si or solution processed Si), there are numerous advances in the organic (semiconducting, conducting and insulating), inorganic and hybrid (organic-inorganic) materials that exhibit customized properties and stability, and in the synthesis and preparation methods, which are characterized by a significant amount of multidisciplinary efforts. Furthermore, the development and encapsulation of organic electronic devices onto flexible polymeric substrates by large-scale and low-cost roll-to-roll production processes will allow their market implementation in numerous application areas, including displays, lighting, photovoltaics, radio-frequency identification circuitry and chemical ...

Energy Technology Data Exchange (ETDEWEB)

Radioisotopes of Pb(II) have been of some interest in radioimmunotherapy and radioimmunoimaging (RII). However, the absence of a kinetically stable bifunctional chelating agent for Pb(II) has hampered its use for these applications. {sup 203}Pb (T{sub 1/2}=52.02 h) has application potential in RII, with a {gamma}-emission that is ideal for single photon emission computerized tomography, whereas {sup 212}Pb (T{sub 1/2}=10 h) is a source of highly cytotoxic {alpha}-particles via its decay to its {sup 212}Bi (T{sub 1/2}=60 min) daughter. The synthesis of the novel bifunctional chelating agent 2-(4-isothiocyanotobenzyl)-1,4,7,10-tetraaza-1,4,7,10-tetra-(2-carbamoyl methyl)-cyclododecane (4-NCS-Bz-TCMC) is reported herein. The Pb[TCMC]{sup 2+} complex was less labile to metal ion release than Pb[DOTA]{sup 2-} at pH 3.5 and below in isotopic exchange experiments. In addition to increased stability to Pb{sup 2+} ion release at low pH, the bifunctional TCMC ligand was ...

Energy Technology Data Exchange (ETDEWEB)

{sup 14}C-Sugar uptake and incorporation into starch by slices of developing maize (Zea mays L.) endosperm were examined and compared with sugar uptake by maize endosperm-derived suspension cultures. Rates of sucrose, fructose, and D- and L-glucose uptake by slices were similar, whereas uptake rates for these sugars differed greatly in suspension cultures. Concentration dependence of sucrose, fructose, and D-glucose uptake was biphasic (consisting of linear plus saturable components) with suspension cultures but linear with slices. These and other differences suggest that endosperm slices are freely permeable to sugars. After diffusion into the slices, sugars were metabolized and incorporated into starch. Starch synthesis, but not sugar accumulation, was greatly reduced by 2.5 millimolar p-chloromercuribenzenesulfonic acid and 0.1 millimolar carbonyl cyanide m-chlorophenylhydrazone. Starch synthesis was dependent on kernel age and incubation ...

International Nuclear Information System (INIS)

Three new rare earth metal-rich compounds, Gd_6MTe_2 (M=Co, Ni) and Er_6RuTe_2, were synthesized in direct reactions between the R, R_3M, and R_2Te_3 (R=Gd, Er, M=Co, Ni, Ru). These materials all adopt the same Zr_6CoAl_2 structure type with space group P6-bar 2m (No. 189, Z=1). Single crystal structures of Gd_6CoTe_2 and Er_6RuTe_2 were determined and lattice parameters are a=b=8.3799(5), c=3.9801(4) A, and a=b=8.1473(5) A, c=3.9962(4) A, respectively. Gd_6NiTe_2 was characterized by X-ray powder diffraction; lattice parameters are a=b=8.412(2), c=3.9577(9) A. Metal-metal bonding correlations were analyzed using the empirical Pauling bond order concept.

British Library Electronic Table of Contents (United Kingdom)

Reaction between [V^I^VO(acac)2] and the ONN donor Schiff base Hpydx-aepy (I) (Hpydx-aepy=Schiff base obtained by the condensation of pyridoxal and 2-aminoethylpyridine) resulted in the formation of a complex [V^I^VO(acac)(pydx-aepy)] (1). Addition of aqueous 30% H2O2 to 1 yields the poor stable oxidoperoxidovanadium(V) complex [V^VO(O2)(pydx-aepy)] (2). Its formation has also been demonstrated in solution by treating 1 with H2O2 in methanol. Reaction of vanadium exchanged zeolite-Y with I in methanol followed by aerial oxidation gave zeolite-Y encapsulated dioxidovanadium(V) complex, abbreviated as [V^VO2(pydx-aepy)]-Y (4). The crystal and molecular structure of 1 has been determined, confirming the ONN binding mode of the ligand. The encapsulated complex [V^VO2(pydx-aepy)]-Y (4) catalyse...

British Library Electronic Table of Contents (United Kingdom)

Crystalline ?-Al2O3 nanowires with diameter, 20?40?nm, length above 600?nm and aspect ratio above 30 have been successfully synthesized by thermal decomposition of boehmite (?-AlOOH) precursors obtained via hydrothermal route by using AlCl3, NaOH and NH3 as starting materials. Thermogravimetric analysis (TG), differential thermal analysis (DTA), X-ray diffraction (XRD), transmission electron microscope (TEM), selected area electron diffraction (SAED) and high resolution transmission electron microscope (HRTEM) were used to characterize the features of the as-made ?-Al2O3 nanowires and their ?-AlOOH precursors. The pH value of the solution and the mixed precipitant play important roles in the formation of ?-AlOOH nanowires. After calcination at 500?C for 2?h, the orthorhombic ?-AlOOH transf...

International Nuclear Information System (INIS)

Ultrafine particles of Sn-Sb alloys with different chemical composition have been prepared by hydrogen plasma-metal reaction. Structure, morphology, size and chemical composition of the Sn-Sb ultrafine particles were investigated by transmission electron microscopy, X-ray diffraction, BET gas adsorption, and induction-coupled plasma spectroscopy. It was found that all the particles have spherical shapes, with average particle size in the range of 100-300 nm. The electrochemistry properties as an alternative anode material for lithium-ion batteries have been characterized by constant current cycling and cyclic voltammetry. Electrochemical measurements showed that the alloys with Sn-46.5 at.% Sb have best reversible capacity and capacity retention. It exhibited a high reversible lithium-ion storage capacity of 701 mAh g"-"1 in the initial cycle, which has remained at 81% (i.e., 566 mAh g"-"1) of its original capacity after 20 cycles.

British Library Electronic Table of Contents (United Kingdom)

A series of NHC silver(I), mercury(II) and palladium(II) complexes, [(1,3-diethylbimy)6Ag4I3]I (2), [(1-benzyl-3-picolylbimy)Ag2Br2]n (3), [(1-benzyl-3-picolylbimy)HgI(CH2CN)]2 (4), {[(1-picolyl-3-npropylbimy)2Hg][Hg2I6]}n (5) and [(1,3-dipicolylbimy)PdCl]Cl (6), as well as one anionic complex [1,3-diethylbimidazolium]2[HgI4] (1) (bimy=benzimidazol-2-ylidene), have been prepared and characterized. Interestingly, a wind wheel-like Ag4I3 arrangement in 2 is formed, 1D polymeric chain containing 12-membered macrometallocycles and quadrangle Ag2Br2 units in 3 is generated, and the a-carbon atom of deprotonated acetonitrile ([CH2CN]-) in 4 participates in coordination with mercury(II) atom. In the crystal packings of complexes 1-6, 2D supramolecular layers or 3D supramolecular architectures are...

British Library Electronic Table of Contents (United Kingdom)

Four extracellular keratinases (designated KI, KII, KIII, and KIV) were produced during submerged aerobic cultivation in a medium containing native human foot skin (NHFS) for enzyme synthesis. The molecular weights, determined by SDS-PAGE, were 25, 50, 34, and 19kDa, respectively. Gel filtration of the four purified enzymes in native conditions indicated that active keratinase KI is a novel homo-octamer, KII a homo-dimer, and KIII and KIV monomers. All four keratinases exhibited high activities at pH 8.0-10.0 with an optimal pH of 9.0. The optimal temperature for keratinolytic activity of KI, KII, and KIII was approximately 50, and 60degreeC for KIV. One millimolar of PMSF completely inhibited the keratinolytic activities of the four enzymes. The N-terminal sequences of KI, KII, and KIII s...

British Library Electronic Table of Contents (United Kingdom)

New palladium(II) and platinum(II) complexes of saccharinate (sac), trans-[Pd(py)"2(sac)"2] (1), cis-[Pt(py)"2(sac)"2] (2), trans-[Pd(3-acpy)"2(sac)"2] (3) and cis-[Pt(3-acpy)"2(sac)"2] (4) (py=pyridine and 3-acpy=3-acetylpyridine) have been synthesized. Elemental analysis, UV-Vis, IR, NMR and TG/DTA characterizations have been carried out. The structures of 1-4 were determined by X-ray diffraction. The palladium(II) and platinum(II) ions are coordinated by two N-bonded sac ligands, and two nitrogen atoms of py or 3-acpy, forming a distorted square-planar geometry. The palladium(II) complexes (1 and 3) are trans isomers, while the platinum(II) complexes (2 and 4) are cis isomers. The mononuclear species in the solid state are connected by weak intermolecular C-H...O hydrogen bonds, C-H...@...

Energy Technology Data Exchange (ETDEWEB)

Platinum complexes play an important role in the development of anticancer drugs. Their cytotoxicity can be influenced by the nature of the leaving ligands, due to the hydrolysis reaction that occurs prior to the binding of the platinum complex to DNA. Also, non-leaving groups such as lipophilic diamines may affect cellular uptake. In this work, we describe the synthesis of platinum(II) complexes having oxalato and long chain aliphatic N-alkyl ethylenediamines as ligands. The products were characterized by elemental analyses, infrared spectroscopy and {sup 1}H, {sup 13}C and {sup 195}Pt NMR spectroscopy. Biological activity was assessed against tumor cell lines (A{sub 549}, B16-F1, B16-F10, MDA-MB-231) and non-tumor cell lines (BHK-21 and CHO). The length of the carbon chain affects the cytotoxicity and the oxalato complexes were less cytotoxic than the respective chloride-containing analogues. (author)

British Library Electronic Table of Contents (United Kingdom)

Phosphor material BaAl2O4:Eu2+, Dy3+ with varying compositions of Sr substitution were prepared by the solid-state synthesis method. The phosphor compositions were characterized for their phase and crystallinity by XRD, SEM and TEM. Photoluminescence (PL) properties were investigated measuring PL and decay time for varying Ba/Sr compositions. The PL results show the blue shift in the luminescence properties in Sr substituted BaAl2O4:Eu2+, Dy3+ compared to parent BaAl2O4:Eu2+, Dy3+. It is probably due to the influence of 5d electron states of Eu2+ in the crystal field because of atomic size variation causing crystal defects. Dy3+ ion doping in the phosphor generates deep traps, which results in long afterglow phosphorescence.

International Nuclear Information System (INIS)

High quality graphene sheets are synthesized through efficient oxidation process followed by rapid thermal expansion and reduction by H2. The number of graphene layers is controlled by tuning the oxidation degree of GOs. The higher the oxidation degree of GOs is getting, the fewer the numbers of graphene layers can be obtained. The material is characterized by elemental analysis, thermo-gravimetric analysis, scanning electron microscopy, atomic force microscopy, transmission electron microscopy and Fourier transform infrared spectroscopies. The obtained graphene sheets with single, triple and quintuplicate layers as anode materials exhibit a high reversible capacity of 1175, 1007, and 842 mA h g-1, respectively, which show that the graphene sheets with fewer layers have higher reversible capacity. -- Graphical abstract: The typical TEM images of the graphene sheets derived from GO3(a), GO2(b) and GO1(c). Display Omitted Highlights: ? With the oxidation degree of GO ...

International Nuclear Information System (INIS)

In this study, perovskite type oxide YAlO_3 has been doped with different amounts of the divalent cation Ca to synthesize Y_1_-_xCa_xAlO_3_-_#delta# (x = 0-0.21) compositions. The effect of dopant concentration on the crystal structure and electrical properties of YAlO_3 synthesized by citrate gel route has been investigated. The phase purity of the samples has been carried out using X-ray diffraction. The microstructural evaluation of the samples has been conducted by scanning electron microscopy and energy dispersive spectrum analysis. Thermal analysis has been conducted to monitor the decomposition of the intermediate products. The electrical conductivity studies have been performed using a.c. impedance spectroscopy as a function of temperature in the range 200-800 "oC in air. The Y_0_._9_4Ca_0_._0_6AlO_3_-_#delta# composition exhibits a total conductivity of 2.5 mS/cm at 800 "oC.

British Library Electronic Table of Contents (United Kingdom)

Cobalt supported on Beta zeolite catalysts were prepared by impregnation of metal salts in aqueous solution and were tested for the Fischer Tropsch reaction. The support consisted of a Beta zeolite composed by crystallites of nanometric dimensions and a SiO2/Al2O3 molar ratio of about 50. This support was impregnated with Co(NO3)2 aqueous solution using different metal loads of 7.5, 10, 15 and 20wt% Co. These materials were characterized by X-ray diffraction (XRD), high resolution transmission electron microscopy (HRTEM), N2 adsorption (BET), thermal programmed reduction (TPR) and FTIR of adsorbed pyridine (i.e., surface acid sites distribution). All the catalysts showed a significant catalytic activity for the F-T reaction from synthesis gas (CO+2H2), in a continuous fixed bed reactor sys...

International Nuclear Information System (INIS)

Brief item.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

The heterogeneous solid catalyst, mercaptopropylsilica (MPS), has been prepared by a modified procedure in water and its structure confirmed by solid state carbon-13 CP-MAS NMR spectrum. This catalyst has been efficiently utilized for the synthesis of a wide variety of tri-, tetrasubstituted imidazoles and their bis-analogues at room temperature. The protocol was further explored for the synthesis of the drug trifenagrel.

DEFF Research Database (Denmark)

ATPase, endoplasmic reticulum, calcium, ischaemia

International Nuclear Information System (INIS)

... odd nuclei organic compounds radiation effects radioisotopes synthesis

Energy Technology Data Exchange (ETDEWEB)

In the framework of the search for a ceramic material usable in the radioactive waste storage, uranium and thorium phosphates have been investigated. Their experimental synthesis conditions have been entirely reviewed, they lead to the preparation of four new compounds: U(UO{sub 2})(PO{sub 4}){sub 2}, U{sub 2}O(PO{sub 4}){sub 2}, UCIPO{sub 4}, 4H{sub 2}O, and Th{sub 4}(PO{sub 4}){sub 4}P{sub 2}O{sub 7}. Experimental evidenced are advanced for non existent compounds such as: U{sub 3}(PO{sub 4}){sub 4}, U{sub 2}O{sub 3}P{sub 2}O{sub 7} and Th{sub 3} (PO{sub 4}){sub 4}. Characterization by several techniques (X-rays and neutron powder diffractions, UV-Visible and Infra-red spectroscopies, XPS,...) were performed. The ab initio structure determination of U(UO{sub 2})(PO{sub 4}){sub 2} has been achieved by X-rays and refined by neutron diffractions. Through its physico-chemical analysis, we found that this compound was a new mixed valence uranium ...

International Nuclear Information System (INIS)

By the methods of the angular distribution of photon annihilation, time distribution of photon annihilation, photoluminescence spectroscopy, Fourier IR-spectroscopy, atomic force microscopy the detail information on relation of the structural and physical properties of the porous nano-structures is obtained. Study of pores sizes in a different nano-porous materials, such as the porous silicon, porous anode aluminium oxide, porous solids exposed to light atoms ion implantation (hydrogen, deuterium, helium) is carried out.

UK PubMed Central (United Kingdom)

After slow progress in the efforts to develop phase plates for electron microscopes, functional phase plate using thin carbon film has been reported recently. It permits collecting high-contrast images...Full Text Available

International Nuclear Information System (INIS)

Nanocrystalline materials can exhibit properties which are considerably different from their coarse-grained counterparts, making them unique for basic or applied research and also very promising for potential applications. The topics which are addressed in the present paper are magnetic properties and magnetic correlations on the nanometer scale, mechanical properties, in particular the influence of grain boundaries on the elastic and plastic behaviour, and vibration models of grain boundary atoms in nanostructured materials. (author)

International Nuclear Information System (INIS)

The new nonlinear optical crystal Rb3V5O14 has been synthesized by solid state reaction and characterized by single-crystal X-ray diffraction, IR and thermogravimetric analysis. The crystal Rb3V5O14 crystallizes in the trigonal system with space P31m (No. 157), a=b=8.7134(12) A, c=5.2807(11) A and ?=90o, ?=90o, ?=120o, Z=1, ?=3.516 g/cm3. It is a layered structure that is very flat and strongly parallel to c. The V5O14 layer structure consists of corner-linked square and triangular pyramids. The layers are separated by Rb+ ions, which fit equally well on the V5O14 layer. The Kurtz powder SHG measurement, using 1064 nm radiation, showed that the second-harmonic generation efficiency of Rb3V5O14 is about two times that of KDP. -- Graphical abstract: The new nonlinear optical crystal Rb3V5O14 has been synthesized by solid state reaction and characterized by single-crystal X-ray diffraction, IR and thermogravimetric analysis. The crystal Rb3V5O14 ...

International Nuclear Information System (INIS)

Full text: HMPAO, a butane monoxime derivative of propylene amine and ECD, ethyl cysteinate dimer, are currently being used as brain imaging agents. In an effort to develop new radiopharmaceuticals for imaging brain, we have synthesized amine and imine derivatives of ethyl cysteinate with butane monoxime, optimized labelling procedure with "9"9"mTc and studied the in vivo behaviour of their "9"9"mTc complexes. Imine derivative of ethyl cysteinate with butane monoxime was synthesized by refluxing equimolar amounts of butane monoxime and ethyl cystinate in dry benzene for 3 hours. The product was purified over silica with 10% ethyl acetate in chloroform as eluent. Amine derivative was prepared by reducing the imine derivative with sodium borohydride. The ligands were characterized by NMR spectroscopy and were found to be pure. The ligands were labelled with "9"9"mTc using stannous chloride as reducing agent. The complexes were characterized by ...

International Nuclear Information System (INIS)

The synthesis, characterization of M"vO([CH_3CH_2N(CH_2CH_2S)_2](p-S-Ph-COOCH_2-CH_3)) (M:"9"9"mTc: I, Re: II) is presented in this work, where a pendant ester function is attached to the monothiolate ligand. Chemical structure of I is established after chromatographic comparison with II, synthesized in macroscopic amounts. Complex II is fully characterized by classical methods of analysis showing that the compound adopts a distorted trigonal bipyramidal configuration around the metal. The two sulfur atoms of the tridentate ligand and the oxo group form the basal plane, while the remaining nitrogen atom of the tridentate ligand and the sulfur atom of the monothiolate ligand occupy the apices of the bipyramid. In vitro challenge experiments with glutathione (GSH) in neutral aqueous medium demonstrate, that I suffers nucleophilic attack by GSH and thereby transformation to a more hydrophilic daughter metal compound. Formation ...

Energy Technology Data Exchange (ETDEWEB)

We describe the synthesis and characterization of superparamagnetic iron oxide nanoparticle based heavy metal sorbents with various surface chemistries that demonstrate an excellent affinity for the separation of heavy metals in contaminated water systems (i.e. spiked Columbia river water). The magnetic nanoparticle sorbents are prepared from an easy to synthesize iron oxide precursor, followed by a simple, one-step ligand exchange technique to introduce the organic surface functionality of interest chosen to target either specific or broader classes of heavy metals. Functionalized superparamagnetic nanoparticles are excellent sorbent materials for the extraction of heavy metal contaminants from environmental and clinical samples since they are easily removed from the media once bound to the contaminant by simply applying a magnetic field. These engineered magnetic nanoparticle sorbents have an inherently high active surface area (often > ...

Science.gov (United States)

The kinetics of benzoate degradation by the anaerobic syntrophic bacterium, Syntrophus buswellii, was studied in coculture with Desulfovibrio strain G11. The threshold value for benzoate degradation was dependent on the acetate concentration with benzoate threshold values ranging from 2.4 [mu]M at 20 mM acetate to 30.0 [mu]M at 65 mM acetate. Increasing acetate concentrations also inhibited the rate of benzoate degradation with a apparent K[sub i] for acetate inhibition of 7.0 mM. Lower threshold values were obtained when nitrate rather than sulfate was the terminal electron acceptor. These data are consistent with a thermodynamic explanation for the threshold, and suggest that there is a minimum Gibbs free energy value required for the degradation of benzoate. An acetoacetyl-CoA thiolase has been isolated from Syntrophomonas wolfei; it is apparently a key enzyme controlling the synthesis of poly-B-hydroxyalkanoate from acetyl-CoA in this organism. Kinetic ...

International Nuclear Information System (INIS)

A burgeoning interest in technetium coordination chemistry has been spurred by its widespread use in nuclear medicine. Recent focus has been on the design and preparation of new technetium complexes, the lipophilicity, polarity, and overall charge of which can be readily altered by simple substitutions in the molecular framework of the ligand in order to optimize the biodistribution and target specific organs. Examples are cationic (Cardiolite) and neutral (Ceretec) technetium complexes, used as myocardial and brain imaging agents, respectively. The authors have been pursuing a continuing study of tris(3-hydroxy-4-pyridinonato)gallium and -indium complexes that are water soluble, are hydrolytically stable, and are of varying lipophilicity and neutral charge. Studies of in vivo in rabbits and mice have revealed that several of these cationic complexes may be useful as morphologic kidney imaging agents, with ["9"9"mTc(pap)_3]"+ showing elevated levels in the kidneys even after 24 h. In ...

International Nuclear Information System (INIS)

The aim of this work is to understand the reasons for the selectivity shown in the complexation by unsaturated heteropolyanions (HPA) of actinides (An) which are oxidized to the number +IV. Different studies have been carried out, both in solution and in solid state, on P_2W_1_7O_6_1"1"0"- and its complexes with Zn"2"+, UO_2"2"+, Ce"4"+, Th"4"+ and U"4"+ to characterize the nature of the complexation site offered to the cation. Among the actinides(IV), the U"4"+ ion has been selected due to its singular spectroscopic and magnetic properties. An initial series of studies, in solution, using NMR"3"1P has thus enabled us to characterize these complexes and to compare them to those formed with the complexing agent PW_1_1O_3_9"8"-. This body of data allows to identify an identical complexation site for both ligands. An analysis of the NMR"3"1P spectrum of U(P_2W_1_7O_6_1)_2"1"6"- has shown a plane of symmetry passing through the actinide and enables ...

UK PubMed Central (United Kingdom)

The t-butyldimethylsilyl group is shown to be an ideal protecting group for the 2T-hydroxyl function of ribonucleosides during the synthesis of ribonucleotides using any of nine commonly used condensing...Full Text Available

UK PubMed Central (United Kingdom)

The accepted model of retroviral reverse transcription includes a circular DNA intermediate which requires strand displacement synthesis for linearization and creation of an integration-competent, long...Full Text Available

International Nuclear Information System (INIS)

There is renewed interest in the +6 oxidation state of iron, ferrate (VI) (FeVIO42-), because of its potential as a benign oxidant for organic synthesis, as a chemical in developing cleaner ('greener') technology for remediation processes, and as an alternative for environment-friendly battery cathodes. This interest has led many researchers to focus their attention on the synthesis of ferrate(VI). Of the three synthesis methods, electrochemical, wet chemical and thermal, electrochemical synthesis has received the most attention due to its ease and the high purity of the product. Moreover, electrochemical processes use an electron as a so-called clean chemical, thus avoiding the use of any harmful chemicals to oxidize iron to the +6 oxidation state. This paper reviews the development of electrochemical methods to synthesize ferrate(VI). The approaches chosen by different laboratories to overcome some of ...

UK PubMed Central (United Kingdom)

A new strategy is presented for the synthesis of graft copolymers using only the ring-opening metathesis polymerization (ROMP). From a ROMP-derived main chain, pendant maleimide functional groups...Full Text Available

UK PubMed Central (United Kingdom)

Cell suspension cultures of tomato, Lycopersicon esculentum Mill. cv VFNT-Cherry, produce phytochelatins (poly[γ-glutamylcysteinyl]glycines) when exposed to cadmium. The synthesis...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Research programs, presented at the contractor's review meeting on indirect liquefaction, are presented on the following topics: oxygenates (methanol) synthesis; Fischer-Tropsch synthesis; product upgrading; and process support engineering evaluations. A total of 18 reports are included. Individual projects are processed separately for the data bases. (CBS)

Energy Technology Data Exchange (ETDEWEB)

Adenosine triphosphate (ATP) is an indicator of living biomass in marine particulates. This report details the method used by Lawrence Berkeley Laboratory to analyze particulate ATP in samples taken from oligotrophic, tropical ocean waters. It represents a synthesis of previously published methods.

UK PubMed Central (United Kingdom)

A short, highly stereoselective (over 97%) synthesis of all-trans squalene is described. Starting with succinaldehyde, a tetraenedichlorodione having the complete squalene skeleton...Full Text Available

UK PubMed Central (United Kingdom)

The accumulation of α-1,4-polyglucans is an important strategy to cope with transient starvation conditions in the environment. In bacteria and plants, the synthesis of glycogen and starch occurs...Full Text Available

International Nuclear Information System (INIS)

Spherical nanostructured Si/C composite was prepared by spray drying technique, followed by heat treatment, in which nanosized silicon and fine graphite particles were homogeneously embedded in carbon matrix pyrolyzed by phenol formaldehyde resin. Cyclic voltammetry tests showed two pairs of redox peaks corresponding to lithiation and delithiation of Si/C composite. The Si/C composite exhibited a reversible capacity of 635 mAh g"-"1 and good cycle performance used in lithium ion batteries. To improve cycle performance of this Si/C composite further, the carbon-coated Si/C composite was synthesized by the second spray drying and heat treatment processing. The cycle performance of carbon-coated Si/C composite was improved significantly, which was attributed to the formation of stable SEI passivation layers on the outer surface of carbon shell which protected the bared silicon from exposing to electrolyte directly.

British Library Electronic Table of Contents (United Kingdom)

The nanostructure Ni-doped CdO films have been prepared by sol gel spin coating method. Atomic force microscopy results indicate that the CdO films are formed from the nanoparticles and the grain size is changed with nickel content. X-ray diffraction patterns of the films indicate that the undoped and Ni-doped CdO films have polycrystalline structure with a cubic sodium chloride structure, showing two main characteristic peaks assigned to the (111) and (200) planes. The optical band gap values of undoped and Ni-doped CdO films were determined by optical absorption method. The Eg values of the CdO films were found to be in the range of 2.26?2.60?eV. The Eg values of the CdO films increase with the content of Ni dopant (up to 6% Ni). It is evaluated that the optical band gap and grain size o...

Energy Technology Data Exchange (ETDEWEB)

We used light confinement in optical microcavities to achieve a strong enhancement and a precise wavelength tunability of the electrical photoconductance of nanostructured porous silicon (PS). The devices consist of a periodic array of alternating PS layers, electrochemically etched to have high and low porosities - and therefore distinct dielectric functions. A central layer having a doubled thickness breaks up the symmetry of the one-dimensional photonic structure, producing a resonance in the photonic band gap that is clearly observed in the reflectance spectrum. The devices were transferred to a glass coated with a transparent SnO{sub 2} electrode, while an Al contact was evaporated on its back side. The electrical conductance was measured as a function of the photon energy. A strong enhancement of the conductance is obtained in a narrow (17nm FWHM) band peaking at the resonance. We present experimental results of the angular dependence of this photoconductance ...

Energy Technology Data Exchange (ETDEWEB)

A model for the structural relaxation of grain boundaries (GBs) in nanostructured materials (NSMs) by diffusion-accommodated rigid body translations along GBs is proposed. The model is based on the results of recent computer simulations that have demonstrated that the GBs in NSMs retain a high-energy structure with random translational states due to severe geometrical constraints applied from neighboring grains (J. Appl. Phys. 78 (1995) 847; Scripta Metall. Mater. 33 (1995) 1245). The shear stresses within a GB caused by non-optimized rigid-body translations (RBTs) can be accommodated by diffusive flow of atoms along a GB. This mechanism is particularly important for low-angle and vicinal GBs, the energy of which noticeably depends on the rigid body translations. At moderate and high temperatures the model yields relaxation times that are very short and therefore GBs in NSMs can attain an equilibrium structure with optimized rigid body translations. In contrast, at ...

International Nuclear Information System (INIS)

Portuguese 2009 1 p. Brazil Magalhaes, Cassia Goncalves Silva, Gracia

International Science & Technology Center (ISTC)

Development of SHS-technologies for SiC, Si3N4 and Ceramic Composites on Their Basis from Rocks

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

We explore the relation of nanostructures with the appearance of giant magnetoresistance (GMR) in melt-spun CuCo ribbons. We find by energy-filtered transmission electron microscopy that the ribbons are composed of a periodic distribution of Co within the Cu, as in spinodal decomposition. The lamellar structure should thus be associated with GMR, as only a small percentage of the Co is present in the form of grains. This is counterintuitive, for no clear interfaces are present as required by standard models, and the period of the composition oscillation (43-52 nm) is an order of magnitude larger than the mean free paths for electrons. Upon annealing, a secondary spinodal decomposition appears following the same direction as the original.

International Nuclear Information System (INIS)

An annealing with the nanosecond laser light pulse is applied for crystal lattice reconstruction of a disturbed near-surface layer, which was created in semiconductor material as a result of the implantation process. Radiation with energy density higher than the threshold value causes the melting of the surface layer and than the epitaxial recrystallization from the melt on a different substrate. Structural changes occurring in the Ge implanted Si crystals after annealing with different energy densities are investigated by means of the cross-section high-resolution transmission electron microscopy. (author)

Energy Technology Data Exchange (ETDEWEB)

This paper reports the presence of face centered cubic cobalt precipitates inside tungsten carbide in nanocomposite of WC-Co synthesized by spray conversion processing. EDS was used to identify the presence and micro-diffraction was employed to determine the nature of the precipitates. There is entrapment of cobalt in tungsten carbide during the spray conversion process used to form WC/Co powder. During consolidation, at high temperatures, the cobalt attains enough mobility to precipitate inside WC. A vanadium containing compound was seen at the interfaces in samples which incorporated VC as a grain growth inhibitor. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive hydrogen cooling and adapted tanks. Chemical storage by hydrides imposes heavy devices. A ...

Energy Technology Data Exchange (ETDEWEB)

Nanoparticles represent versatile building blocks in material science and nanotechnology. Thereby, the defined assembly of nanostructures (13 and 56 nm in diameter, respectively) is of significant importance. Short DNA sequences can be bound to the nanoparticle surface thus enabling highly specific DNA hybridization-driven events that direct the formation of nanoparticle constructs.In this paper, examples for the defined formation of gold nanoparticle constructs are demonstrated. In addition, gold-silver core-shell nanoparticles are introduced as further building blocks for the hybridization-controlled formation of nanoparticle constructs.

International Nuclear Information System (INIS)

We have recently shown the applicability of robotics to the synthesis of a positron-emitting radiopharmaceutical, namely 16#alpha#[F-18]fluoroestradiol-17#beta#, a breast tumor imaging agent. We now report the application of the robot to the synthesis of two additional radiopharmaceuticals, [F-18]spiroperiodol and [C-11]butanol. This achievement shows the power of a robot as a multifunctional automated device for the synthesis of several positron-emitting radiopharmaceuticals in limited laboratory space. (author).

Energy Technology Data Exchange (ETDEWEB)

This invention pertains to a Fischer Tropsch process for converting synthesis gas to an oxygenated hydrocarbon with particular emphasis on dimethyl ether. Synthesis gas comprising carbon monoxide and hydrogen are converted to dimethyl ether by carrying out the reaction in the presence of an alkali metal-manganese-iron carbonyl cluster incorporated onto a zirconia-alumina support.

International Nuclear Information System (INIS)

The anodic reaction kinetics and interfacial mass transport of a direct polymer electrolyte membrane formic acid fuel cell have been investigated in an all solid-state electrochemical cell using a highly active nanostructured palladium-gold alloy microelectrode as an in situ probe. Well-defined 'S-shaped' steady-state cyclic voltammograms exhibiting current-rising region at lower overpotentials and limiting current region at higher overpotentials have been first obtained for the electrochemical oxidation of formic acid at varying temperature. The 'S-shaped' steady state polarization curves and chronoamperometric curves enable convenient measurements of the anodic reaction kinetics and interfacial mass transport of formic acid under real polymer electrolyte membrane conditions. It is encouragingly found that formic acid can be directly oxidized to CO2 with the first electron transfer being the likely rate-determining step and the formation of surface poison can be ...

International Nuclear Information System (INIS)

SiC-AlN and SiC-SiAlON refractory composites were obtained by means of nitridation of the mixtures of silicon carbide (SiC) powder with a broad granulometric distribution and powders of aluminium (Al) and aluminium-silicon (Al-Si) mixtures. The mixtures of the composition Al-25% Si, Al-50% Si and Al-75% Si were previously prepared by means of 'mechanical alloying' technique. Thermodynamic analysis was accomplished in order to evaluate the viability of SiC-SiAlON and SiC-AlN refractories production by the chosen processing method, and the results confirmed viability of such. Investigation of nitridation of Al and Al-Si powder compacts in order to obtain the AlN and #beta#-SiAlON matrix phases of the composite was accomplished by means of differential thermal analysis (DTA) and thermogravimetric analysis (TG). The results of the thermal analysis show that nitridation of the Al-25% Si, Al-50% Si and Al-75% Si resulting in p-SiAlON formation occur at temperatures of 910 deg C, 811 deg C ...

International Nuclear Information System (INIS)

The 177 underground storage tanks at the DOE's Hanford Site contain an estimated 180 million tons of high-level radioactive wastes. It is desirable to remove and concentrate the highly radioactive fraction of the tank wastes for vitrification. Resorcinol-formaldehyde (R-F) resin, an organic ion-exchange resin with high selectivity and capacity for the cesium ion, which is a candidate ion-exchange material for use in remediation of tank wastes. The report includes information on the structure/function analysis of R-F resin and the synthetic factors that affect performance of the resin. CS-100, a commercially available phenol-formaldehyde (P-F) resin, and currently the baseline ion-exchanger for removal of cesium ion at Hanford, is compared with the R-F resin. The primary structural unit of the R-F resin was determined to consist of a 1,2,3,4-tetrasubstituted resorcinol ring unit while CS-100, was composed mainly of a 1,2,4-trisubstituted ring. CS-100 shows the presence of phenoxy-ether ...

Energy Technology Data Exchange (ETDEWEB)

Barbiturates substituted at the 5-position with organyltelluroalkyl or organylselenoalkyl groups were prepared by ring annulation of appropriately substituted diethyl malonates with urea or thiourea. The substituted diethyl malonates (phenyltellurobutyl(ethyl), i-propyltelluropropyl(ethyl), i-propyltelluropropyl(allyl), i-propyselenopropyl(ethyl), and phenylselenohexyl(methyl)) were prepared in 55-91% yield by reaction of diethyl omega-bromoalkyl(alkyl)malonates with organyltellurolates or selenolates (RXNa; X = Se, Te) in ethanol/benzene. The following barbiturates were obtained in 28-84% yield: phenyltellurobutyl(ethyl), m.p. 100/sup 0/C; i-propyltelluropropyl(ethyl), m.p. 119/sup 0/C; i-propylselenopropyl(ethyl), m.p. 137/sup 0/C; phenyl-selenohexyl(methyl), m.p. 124/sup 0/C. The 5-substituted thiobarbiturates i-propyltelluropropyl(ethyl)-(m.p. 75/sup 0/C) and i-propylselenopropyl(ethyl)thiobarbiturate (m.p. 83/sup 0/C) were isolated in 32 and 20% yield, respectively. The ...

Energy Technology Data Exchange (ETDEWEB)

The symmetrical complexes [{sup 99m}Tc][TcN(R{sub 2}PS{sub 2}){sub 2}] [R = CH{sub 3}, CH{sub 2}CH{sub 3}, CH{sub 2}CH{sub 2}CH{sub 3}, CH{sub 2}(CH{sub 3}){sub 2}], and the unsymmetrical complex [{sup 99m}Tc][TcN(Me{sub 2}PS{sub 2})(Et{sub 2}PS{sub 2})] have been prepared, at tracer level, through a two-step procedure involving the preliminary formation of a prereduced technetium nitrido intermediate followed by substitution reaction onto this species by the appropriate dithiophosphinate ligand [R{sub 2}PS{sub 2}]Na. The chemical identity of the resulting complexes have been established by comparison with the corresponding {sup 99}Tc-analogs prepared, at macroscopic level, by reacting the complex [{sup 99}TcNCl{sub 4}] [n-Bu{sub 4}N] (n-Bu = n-butyl) with an excess of ligand in methanol, and characterized by elemental analyses and spectroscopic techniques. The complexes are neutral and lipophilic, and possess a square pyramidal geometry, with an apical Tc N group ...

Energy Technology Data Exchange (ETDEWEB)

Mixed-conducting ceramic oxides have potential uses in high-temperature electrochemical applications such as solid oxide fuel cells, advanced batteries, sensors, and oxygen-permeable membranes. The Sr-Fe-Co-O system combines high electronic/ionic conductivity with appreciable oxygen permeability at elevated temperatures. Dense ceramic membranes made of this material can be used to separate high-purity oxygen from air without the need for external electrical circuitry, or to partially oxidize methane to produce syngas. Samples of Sr{sub 2}Fe{sub 3{minus}x}Co{sub x}O{sub y} (with x = 0, 0.6, 1.0, and 1.4) were prepared by solid-state reaction in atmospheres with various oxygen partial pressures (pO{sub 2}) and were characterized by X-ray diffraction, scanning electron microscopy, and electrical conductivity measurements. Phase components of the samples are dependent on cobalt concentration and synthesis pO{sub 2}. Total conductivity increases ...

Energy Technology Data Exchange (ETDEWEB)

Recognizing the importance of {sup 99m}Tc and {sup 99m}Tc-based radiopharmaceuticals in nuclear medicine, the Philippine Nuclear Research Institute has initiated research on the development of column-type generators for {sup 99m}Tc using {sup 99}Mo in the form of a gel. The use of reactor-produced {sup 99}Mo will reduce the country's dependence on the importation of commercial generators based on fission product molybdenum-99. However, the relatively low specific activity of {sup 99}Mo must be compensated by the high adsorption capacity of the column material for molybdenum. A procedure based on the incorporation of low activity {sup 99}Mo into a zirconium molybdate gel matrix was adopted with reasonable success. Because the properties of the gel vary considerably with conditions of synthesis, the following parameters were carefully controlled: pH, concentration, temperature, order of mixing of the reactant solutions and conditions of aging, washing and ...

International Nuclear Information System (INIS)

Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized under a high magnetic field of 10 T. The formation mechanism was investigated and discussed in detail. The synthesized samples were characterized by XRD, SEM, TEM, EMPA, and vector network analysis. By doping MnO2 with Fe, the relative complex permittivity of MnO2 and its corresponding loss tangent clearly decreases, but its relative complex permeability and its corresponding loss tangent markedly increases. Moreover, the theoretically calculated values of reflection loss show that with increasing the Fe content, the as-prepared Fe-doped MnO2 exhibits good microwave absorption capability. -- Graphical Abstract: Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized in a high magnetic field of 10 T via a simple chemical process. Display Omitted Highlights: ? Fe-doped MnO2 with a hollow sea urchin-like ball chain shape was first synthesized. ? We ...

Energy Technology Data Exchange (ETDEWEB)

The synthesis, characterization, and photophysical properties of several Pt(II) complexes of quinoxaline-2,3-dithiolate (qdt) and 6,7-dimethylquinoxaline-2,3-dithiolate (dmqdt) are described. Specifically, (TBA){sub 2}[Pt(qdt){sub 2}], where TBA = tetra-n-butylammonium, Pt(COD)(qdt), where COD = 1,5-cyclooctadiene, and Pt(phen)(qdt), where phen = 1,10-phenanthroline, and their dmqdt analogs have been prepared and examined with respect to their photophysical properties. Highly structured emission from Pt(COD)(qdt) in frozen glass solution at 77 K has been detected, having a major vibrational progression of 1370 cm{sup {minus}1} corresponding to a C=C stretching frequency of the quinoxalinedithiolate backbone. Solution luminescence from (TBA){sub 2}[Pt(qdt){sub 2}] and Pt(phen)(qdt) has been detected with quantum yields, {Phi}{sub em}, of 10{sup {minus}5} and 10{sup {minus}3}, respectively, although the latter is highly sensitive to solvent ...

Science.gov (United States)

Five hydrated inorganic divalent cations, Mg[sup 2+], Co[sup 2+], Ni[sup 2+], Cu[sup 2+], and Zn[sup 2+], have successfully been used as templates for the synthesis of manganese oxide octahedral molecular sieves (OMS-1) having the todorokite structure. The OMS-1 samples have been well characterized by X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy dispersive X-ray studies, inductively coupled plasma analysis, electron paramagnetic resonance, Fourier transform infrared spectroscopy, thiosulfate titration, and cyclohexane sorption. Catalytic CO oxidation and 2-propanol decomposition were carried out. Results show that these OMS-1 samples with a tunnel size of about 6.9 angstroms are crystalline and chemically pure. They have the following formulas: Mg[sub 3.17]Mn[sub 5.05]O[sub 12] [center dot] 4.52H[sub 2]O, Co[sub 1.84]Mn[sub 5.59]O[sub 12] [center dot] 3.45H[sub 2]O, Ni[sub ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this research project is to investigate the biocompatibility of N-isopropylacrylamide (NIPAAm) monomers and poly(N-isopropylacrylamide) (PNIPAAm) nanoparticles in vitro. PNIPAAm nanoparticles of different sizes were synthesized and characterized by transmission electron microscopy and dynamic light scattering. Cytotoxicity studies using MTS assays were conducted on fibroblasts, smooth muscle cells, and endothelial cells. In addition, the concentration of NIPAAm monomers remaining on PNIPAAm nanoparticles was determined using bromination and spectrophotometry. The cytotoxicity results did not show a significant difference in cell survival when cells were exposed to different particle sizes (100, 300, and 500 nm). Dose studies showed that all three cell types exposed to 100 nm PNIPAAm nanoparticles at concentrations less than or equal to 5 mg/mL were compatible, while cells exposed to NIPAAm monomers exhibited toxicity even at very low ...

Energy Technology Data Exchange (ETDEWEB)

Samarium cobaltite ceramic perovskites, with and without platinum particles dispersion, are possible candidates as electrode for electrochemical conversion of hydrocarbon and for intermediate temperature solid oxide fuel cells (ITSOFC). In this work, samarium cobaltites were synthesized by the combustion method using cobalt, and samarium nitrates as cation precursors and urea as fuel. For containing-platinum compositions Pt (II) acetyl acetonate was also employed as precursor. The effect of Sr on the phase formation and its electrical behavior is also studied. Specific surface area (BET), SEM-EDX, TEM and XRD analysis are used to characterize the powders obtained. Powders were pressed into pellets and sintered in air in the temperature range of 1200 -1400 C. Electrical impedance spectroscopy studies (EIS) are performed on sintered samples. The as-prepared powders showed an amorphous structure and by TEM a very small particle size ({proportional_to}10 nm) was ...

DEFF Research Database (Denmark)

Antisense- or RNAi-mediated suppression of the biosynthesis of nutritionally inferior storage proteins is a promising strategy for improving the amino acid profile of seeds. However, the potential pleiotropic effects of this on interconnected pathways and the agronomic quality traits need to be addressed. In the current study, a transcriptomic analysis of an antisense C-hordein line of barley was performed, using a grain-specific cDNA array. The C-hordein antisense line is characterized by marked changes in storage protein and amino acid profiles, while the seed weight is within the normal range and no external morphological irregularities were observed. The results of the transcriptome analysis showed excellent correlation with data on changes in the relative proportions of storage proteins and amino acid composition. The antisense line had a lower C-hordein level and down-regulated transcript encoding C-hordein. The production of the S-rich B/ - and D-hordeins ...

Energy Technology Data Exchange (ETDEWEB)

This report summarises nearly 20 biosphere reports and gives a synthesis of the work performed within the SR-Site Biosphere project, i.e. the biosphere part of SR-Site. SR-Site Biosphere provides the main project with dose conversion factors (LDFs), given a unit release rate, for calculation of human doses under different release scenarios, and assesses if a potential release from the repository would have detrimental effects on the environment. The intention of this report is to give sufficient details for an overview of methods, results and major conclusions, with references to the biosphere reports where methods, data and results are presented and discussed in detail. The philosophy of the biosphere assessment was to make estimations of the radiological risk for humans and the environment as realistic as possible, based on the knowledge of present-day conditions at Forsmark and the past and expected future development of the site. This was achieved by using the ...

Energy Technology Data Exchange (ETDEWEB)

No abstract available.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... Accession Number : ADD335809. Title : Characterization of Absolute-Resonant Eddy Current Probes,. Corporate Author : ...

Energy Technology Data Exchange (ETDEWEB)

Carbon monoxide, H{sub 2}, and CO{sub 2} in synthesis gas can be converted to CH{sub 4} by employing a triculture of Rhodospirillum rubrum, Methanosarcina barkeri, and Methanobacterium formicicum. Trickle-bed reactors have been found to be effective for this conversion because of their high mass-transfer coefficients. This paper compares results obtained for the conversion of synthesis gas to CH{sub 4} in 5-cm- and 16.5-cm-diameter trickle-bed reactors. Mass-transfer and scale-up parameters are defined, and light requirements for R. rubrum are considered in bioreactor design.

Energy Technology Data Exchange (ETDEWEB)

Iodine-125 labelled vinyl and aryl iodides are formed via the reaction of sodium iodide-125 with vinyl- and arylboronic acids. Good yields of isomerically pure products are obtained.

International Nuclear Information System (INIS)

Short communication.

KoreaScience (Korea)

Full Text Available

Wastenet

...Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Synthesis of low-temperature, fast, single-firing body for porcelain stoneware ... tiles with coal gangue Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Wei et al.,... Article Synthesis of low-temperature, fast, single-firing body for porcelain stoneware tiles with coal gangue Qiangwei Wei1, Wenyuan Gao1*, and Xinguo ...According to phase diagram theory, a low-temperature, fast, single-firing body mix for porcelain stoneware tiles was designed in the quaternary system CaO-MgO-Al2O3-SiO2, using ...

CERN Document Server

Proteins are polymers of amino acids. These macromolecules are synthesized by intracellular machines called {\\it ribosome}. Although, traditionally, the experimental investigation of protein synthesis has been an active area of research in molecular cell biology, important quantitative models of this phenomenon have been reported mostly in the research journals devoted to statistical physics and related interdisciplinary topics. From the perspective of a physicist, protein synthesis is a phenomenon of {\\it classical transport of interacting ribosomes on a messenger RNA (mRNA) template} that dictates the sequence of the amino acids on the protein. Here we bring this frontier area of contemporary research into the classroom by appropriate simplification of the models and methods. In particular, we develope a simple toy model and analyze it by some elementary techniques of non-equilibrium statistical mechanics to predict the average rate of ...

UK PubMed Central (United Kingdom)

Synthesis of wild-type Neurospora crassa assimilatory nitrate reductase is induced in the presence of nitrate ions and repressed in the presence of ammonium ions. Effects of several...Full Text Available

Science.gov (United States)

... 0.2 ml each were taken. The reaction was stopped by the addition of 1 ml LO% trichloracetic acid (TCA) in 0.1 mole of pyrophosphate ...

Science.gov (United States)

Current models of DNA repair of biological damage are reviewed correlating the similarity between carcinogenesis and mutagenesis theories. (PCS)

UK PubMed Central (United Kingdom)

SummaryA microreactor for electrochemical synthesis has been designed and fabricated. It has been shown that different reactions can be carried out successfully using simple protocols.

British Library Electronic Table of Contents (United Kingdom)

SnO2/graphene nanocomposites have been fabricated by a simple chemical method. In the fabrication process, the control of surface charge causes echinoid-like SnO2 nanoparticles to be formed and uniformly decorated on the graphene. The electrostatic attraction between a graphene nanosheet (GNS) and the echinoid-like SnO2 particles under controlled pH creates a unique nanostructure in which extremely small SnO2 particles are uniformly dispersed on the GNS. The SnO2/graphene nanocomposite has been shown to perform as a high capacity anode with good cycling behavior in lithium rechargeable batteries. The anode retained a reversible capacity of 634 mA?h?g?1 with a coulombic efficiency of 98% after 50 cycles. The high reversibility can be attributed to the mechanical buffering by the GNS against...

International Nuclear Information System (INIS)

Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a tool for the thermal property and microstructural analysis of ultrafine-grained ...

International Nuclear Information System (INIS)

Nano structured carbon nitride thin films were deposited at different RF powers in the range of 50 W to 225 W and constant gas ratio of (argon: nitrogen) Ar:N_2 by RF magnetron sputtering. The atomic percentage of Nitrogen: Carbon (N/C) content and impedance of the films increased from 14.36% to 22.31% and 9 x 10"-"1 #OMEGA# to 7 x 10"5 #OMEGA# respectively with increase in RF power. The hardness of the deposited films increased from 3.12 GPa to 13.12 GPa. The increase in sp"3 hybridized C-N sites and decrease of grain size with increase in RF power is responsible for such variation of observed mechanical and electrical properties.

British Library Electronic Table of Contents (United Kingdom)

The formation of nanoparticles during the radiation-induced chemical reduction of silver ions, copper ions, and nickel ions in films based on poly(acrylic acid)-poly(ethylenimine) complexes are studied via electron microscopy. This approach allows preparation of composites containing nanoparticles that are randomly distributed in the polymer matrix and materials with a regular spatial distribution of nanoparticles across the film thickness and in subsurface layers. The structure of metal-polymer hybrid materials is dependent on the irradiation conditions, the type of reduced metal ions, and their initial content in polymer matrices. The ratio between the rate of nucleation and the rate of growth of nanoparticles in the matrices of interpolyelectrolyte complexes depends on the intensity of ...

International Nuclear Information System (INIS)

One-dimensional core-shell polymer nanowires offer many advantages and great potential for many different applications. In this paper we introduce a highly versatile two-step template wetting process to fabricate two-component core-shell polymer nanowires with controllable shell thickness. PLLA and PMMA were chosen as model polymers to demonstrate the feasibility of this process. Solution wetting with different concentrations of polymer solutions was used to fabricate the shell layer and melt wetting was used to fill the shell with the core polymer. The shell thickness was analyzed as a function of the polymer solution concentration and viscosity, and the core-shell morphology was observed with TEM. This paper demonstrates the feasibility of fabricating polymer core-shell nanostructures using our two-step template wetting process and opens the arena for optimization and future experiments with polymers that are desirable for specific applications.

British Library Electronic Table of Contents (United Kingdom)

Only 15mol% of l-proline in ethanol proved to be a very efficient catalyst for the one-pot synthesis of a wide variety of highly substituted pyridines at room temperature. The methodology is mild, efficient, high yielding, and the products can be directly recrystallized from hot ethanol.

Energy Technology Data Exchange (ETDEWEB)

This article describes the utilization of plastic wastes in a blast furnace. The plastic waste is a substitution for petroleum and coal as a raw material for synthesis gas production. The synthesis gas is the reducing agent in the blast furnace for the reduction of iron ores. You can find here an ecological and economical analysis of this process in comparison to the utilization of petroleum and coal. (SR)

International Nuclear Information System (INIS)

The purpose of work is systematical studying of benzo (B) of thiophene-1,1-dioxides and their 2,3-di-hydro derivatives behaviour in the reactions of electrophflic, radical, nucleophilic nitration, reduction of nitro group, embodiment of synthesis of N-amino derivatives, investigation of sulfur containing hetero-cyclic compounds, including of residues of some steroids

British Library Electronic Table of Contents (United Kingdom)

The synthesis of novel b-functionalized derivatives of the clinically used photosensitizer Temoporfin has been achieved by nucleophilic addition reactions to a corresponding diketo chlorin. The b-substituted dihydroxychlorin products exhibit a strong absorption in the red spectral region, a high singlet oxygen quantum yield, and were found to be highly effective in in vitro assays against HT-29 tumor cells.

Energy Technology Data Exchange (ETDEWEB)

With the aim of an experimental check on the validity of the theory of molecular recognition, the authors have carried out the chemical-enzymatic synthesis and cloning of the gene of human calcitonin and also of the genes of antisense polypeptides to human calcitonin and miniproinsulin. It has been shown that recombinant plasmids obtained on the basis of these synthetic genes are capable of ensuring the biosynthesis of the given polypeptides in E. coli cells as hybrid proteins with the IgG-binding domain of staphylococcal protein A.

Energy Technology Data Exchange (ETDEWEB)

Stable strange quark matter produced in the QCD phase transition in the early universe will trap neutrons and repel protons, thus reducing primordial helium production, Ysub(p). For reasonable values of Ysub(p), the radius of strange droplets must exceed 10/sup -6/ cm if strange matter shall solve the dark-matter problem without spoiling Big Bang helium synthesis. (orig.).

UK PubMed Central (United Kingdom)

OBJECTIVES: To assess the suitability of analyzing functional images of brain serotonin (5-HT) synthesis with statistical parametric mapping (SPM), and to investigate further possible sex-related regional...Full Text Available

Science.gov (United States)

Partial Contents: Ternary Compounds; Granular Superconductors; Superconductivity in (SN)x and its Halogen Derivative (SNBr0.4)x; Studies of cuCl at Elevated Pressures; Superconducting Properties of Hydride Systems; Thin Film Superconducting Materials Research; Synthesis of Superconducting Nb3Si using High Pressures; Synthesis of Unstable A-15 Compounds by Epitaxial Recrystallization of Ion Implanted Layers; and Sputtering of Nb3Si.

International Nuclear Information System (INIS)

The extracellular matrix (ECM) of the distal tissues in a newt limb stump is completely reorganized in the 2-3-week period following amputation. In view of numerous in vitro studies showing that extracellular material influences cellular migration and proliferation, it is likely that the changes in the limb's ECM are important activities in the process leading to regeneration of such limbs. Using biochemical, autoradiographic, and histochemical techniques we studied temporal and spatial differences in the synthesis of glycosaminoglycans (GAGs) during the early, nerve-dependent phase of limb regeneration. Hyaluronic acid synthesis began with the onset of tissue dedifferentiation, became maximal within 1 weeks, and continued throughout the period of active cell proliferation. Chondroitin sulfate synthesis began somewhat later, increased steadily, and reached very high levels during chondrogenesis. During the first 10 days ...

Energy Technology Data Exchange (ETDEWEB)

Single crystals of RbBaTaS{sub 4} (1) and K{sub 2}BaTa{sub 2}S{sub 11} (2) were obtained from the reactions of Ta, with in situ formed fluxes of A{sub 2}S{sub 3} (A = K, Rb), BaS, and S at 500 C. Compound 1 crystallizes in the orthorhombic space group Pnma with a = 9.3286(5), b = 7.0391(4), c = 12.4365(7) A, V = 816.6(1) A{sup 3}, Z = 4. Compound 2 crystallizes in the monoclinic space group P2{sub 1}/c with a = 14.5280(10), b = 12.6347(7), c = 17.5148(12) A, {beta} = 94.744(8) , V = 3203.9(4) A{sup 3}, Z = 4. The structure of RbBaTaS{sub 4} (1) consists of isolated tetrahedral [TaS{sub 4}]{sup 3-} anions and Rb{sup +} and Ba{sup 2+} cations. The Ba{sup 2+} cations are surrounded by nine sulfur atoms forming distorted tricapped trigonal prisms, whereas the Rb{sup +} cations are in an irregular environment of ten sulfur atoms. The structure of K{sub 2}BaTa{sub 2}S{sub 11} (2) consists of two different dinuclear [Ta{sub 2}S{sub 11}] units which are separated by Ba{sup 2+} and K{sup +} ...

International Nuclear Information System (INIS)

Spectral-luminescent characteristics of Sr2Y8(SiO4)6O2: Eu powder crystal phosphor with the apatite structure and high-intensity luminescence of Eu3+ ions have been studied. The charge state of europium in the samples has been characterized by means of X-ray L3-adsorption spectroscopy. It was established that Eu3+ forms two types of optical centers. Besides, luminescence of Eu2+ions was found. Reduction Eu3+#->#Eu2+ was considered, which may be due to VSr|| vacancy formation in the 4f crystal lattice position and to negative charge transfer by this vacancy to two EuY3+ ions. Thus, in the silicate lattice there exist inhomogeneously distributed oxygen-deficient centers, which are responsible for nonradiative transfer of excitation energy to Eu3+ and Eu2+ ions. To study electron-vibrational interactions in the crystal phosphor samples, their IR and Raman spectra were examined. In the luminescence spectrum of Eu2+, a series of low-intensity bands caused by ...

Science.gov (United States)

Feasibility of depositing continuous films of nano-porous alumino-silicates, primarily zeolites and MCM-41, on metallic and non-metallic substrates was examined with an aim to develop membranes for separation of gaseous mixtures and also for application as hydrogen storage material. Mesoporous silica was deposited in-side the pores of these nano-porous disks with an aim to develop membranes for selective separations. Our study involves supported zeolite film growth on substrates using in-situ hydrothermal synthesis. Faujasite, Silicalite and Mesoporous silica have been grown on various metallic and non-metallic supports. Metallic substrates used for film growth included anodized titanium, sodium hydroxide treated Titanium, Anodized aluminum, and sintered copper. A non-metallic substrate used was nano-porous aluminum oxide. Zeolite film growth was characterized using Scanning Electron Microscope (AMRAY 1820) and High Resolution Transmission ...

Energy Technology Data Exchange (ETDEWEB)

This was a university-based research project in support of distributed reforming production technologies for hydrogen. Our objective was to examine the steam reforming of bio-ethanol and other related bio-derived liquids over non-precious metal catalyst systems to enable small-scale distributed hydrogen production technologies from renewable sources. The study targeted development of a catalytic system that does not rely on precious metals and that can be active in the 350-550 C temperature range, with high selectivity and high stability. To this end, we adopted a multi-prong research strategy, that included catalyst formulation and synthesis, detailed catalyst characterization, reaction kinetics and reaction engineering, molecular modeling and economic analysis studies. Our approach was an iterative one, where the knowledge gained in one aspect of the study was utilized to modify and fine-tune catalyst development. The research addressed many ...

Energy Technology Data Exchange (ETDEWEB)

Rhenium is technetium`s third row congener and exhibits many of the chemical properties that technetium displays. Theoretically, a Re-PhAT complex will be isostructural with the {sup 99m}Tc PhAT complexes that have been prepared for use as brain imaging agents. A series of neutral rhenium(V) oxo complexes was synthesized by the reaction of ReOBr{sub 4}{sup {minus}} with diamino-thiol-thioether ligands of the type (RSC(CH{sub 3}){sub 2})CH{sub 2}NH(o-C{sub 6}H{sub 4})NHCH{sub 2}C(CH{sub 3}){sub 2}SH. The complexes were characterized by IR, UV/visible, and {sup 1}H and {sup 13}C NMR spectroscopy and by fast-atom-bombardment mass spectroscopy. The single-crystal X-ray structure determination on two of the complexes, where R = CH{sub 2}CH{double_bond}CH{sub 2} and CH{sub 2}CH{sub 2}-CH{sub 3}, showed them to consist of a square pyramidal Re{sup V}ON{sub 2}S{sub 2} core. ReO[CH{sub 2}{double_bond}CHCH{sub 2}SC(CH{sub 3}){sub 2}CH{sub 2}N(o-C{sub 6}H{sub 4})NCH{sub ...

Science.gov (United States)

We have used a cell-free polymerase I transcription system derived from HeLa cells to study the regulation of human rRNA synthesis. Analysis of deletion mutants spanning the start site of transcription at nucleotide +1 indicates that the control region affecting initiation of human rRNA synthesis is contained within sequences from nucleotides -158 to +18. This promoter region can be subdivided into (i) a central segment of approximately 40 base pair that is required for transcription and (ii) flanking sequences that influence the efficiency of transcription in vitro. We have examined the in vitro transcriptional activity of the human extract under various conditions that are thought to modulate rRNA synthesis in vivo. Cell-free extracts prepared from HeLa cells infected with adenovirus 2 synthesize human rRNA at levels greatly decreased relative to uninfected cell extracts. By contrast, in vitro transcription of human rRNA ...

UK PubMed Central (United Kingdom)

Venomous mammals are rare, and their venoms have not been characterized. We have purified and characterized the blarina toxin (BLTX), a lethal mammalian venom with a tissue kallikrein-like activity...Full Text Available

Science.gov (United States)

... 041889 Molecular Cloning and Characterization of Three Novel Lysozyme-Like Genes, Predominantly Expressed in the Male Reproducti...