Energy Technology Data Exchange (ETDEWEB)

To study the effect of CuO on the electrochemical properties of MgNi alloy, the MgNi-xCuO (x = 3, 5 and 10 wt%) composites were prepared by ball-milling method. The X-ray diffraction (XRD) analysis showed that the structures of the composites were amorphous. The cycle stability of the composites was improved compared to pure MgNi alloy due to the enhancement of the anti-corrosion property in the alkaline electrolyte, and the composite with 5 wt% CuO ball-milled for 15 h exhibited the best performance. Electrochemical impedance spectroscopy (EIS) and potential-step measurements indicated that the electrochemical kinetics of the composites was improved.

International Science & Technology Center (ISTC)

Nanostructured Materials from Impulse Plasma in Liquid: Studying of Physical-Chemical Properties, Optimization of Conditions of Obtaining

Energy Technology Data Exchange (ETDEWEB)

The magnetic properties of diluted spinels Zn{sub 1-x}M{sub x}Fe{sub 2}O{sub 4} (M = Mg, Ni) systems have been studied by mean field theory, probability law and high-temperature series expansions method in the range 0 {<=} x {<=} 1. The exchange interactions are calculated by the first and second theory, respectively. The magnetic phase diagrams of Zn{sub 1-x}M{sub x}Fe{sub 2}O{sub 4} (M = Mg, Ni) are calculated by the high-temperature series expansions, combined with the Pade approximants method. The critical exponent associated with the magnetic susceptibility ({gamma}) is deduced.

International Science & Technology Center (ISTC)

Multi-functional Bioactive Nano-structured Coatings for Load-Bearing Implants

Energy Technology Data Exchange (ETDEWEB)

We have developed a Bragg curve counter (BCC) equipped with an active cathode to extend the energy acceptance to lower energies than for a conventional BCC to measure differential cross-sections of fragment production reactions induced by tens of MeV protons. The signal from the active cathode providing the timing signal of fragment incidence and the time difference signal between the cathode and anode gives information on the fragment range in the BCC on the basis of electron drift time. Utilization of the range information made possible identification of fragments less than 0.5 MeV/u that is lower than the identification threshold of a conventional BCC technique. After investigations on fundamental properties of a newly constructed BCC using heavy ion beams and alpha-particles, this method was applied successfully to a fragment production measurement for 70 MeV proton-induced ...

Energy Technology Data Exchange (ETDEWEB)

We have developed an energy-extension method of a Bragg curve counter (BCC) at the high-energy end for the measurements of double-differential cross-sections (DDXs) of fragment productions induced by tens of MeV protons. In this method, we estimate the incident energies of the fragments penetrating a BCC on the basis of the energy loss and atomic number (Z). We applied this method to the DDX measurements of the {sup nat}C(p, Li) and {sup nat}C(p, Be) reactions induced by 70 MeV protons. The validity of this method has been confirmed by comparing the DDXs of beryllium with theoretical predictions of the PHITS code and the two-body kinematics. This method improves the energy acceptance of the BCC for light fragments twice as wide as that of a conventional method without remodeling of the BCC and any loss of the original advantages.

Energy Technology Data Exchange (ETDEWEB)

A body-centered cubic (bcc) Mg-12Li-9Al-1Zn (wt.%) alloy was fabricated in air by electrolysis from LiCl-KCl molten salt at 500 deg. C. Electrolytic deposition of Li atoms on cathode (Mg-Al-Zn alloy) and diffusion of the Li atoms formed the bcc Mg-Li-Al-Zn alloy with 12 wt.% Li and only 0.264 wt.% K. Low K concentration in the bcc Mg alloy strip after the electrolysis process resulted from 47% atomic size misfit between K and Mg atoms and low solubility of K in Mg matrix.

Science.gov (United States)

A novel reactor combining a flame-deposited nanostructured titanium dioxide film and a set of embedded ceramic electrodes was designed, developed and tested for degradation of methyl tert-butyl ether (MTBE) in water. On applying a voltage to the ceramic electrodes, a surface coro...

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

We describe a simple one-pot thermal decomposition method for the production of a stable colloidal suspension of narrowly dispersed superparamagnetic Fe3O4-Ag core-shell nanostructures. These biocompatible nanostructures are highly toxic to microorganisms. Antimicrobial activity studies were carried out on both Gram negative (Escherichia coli and Proteus vulgaris) and Gram positive (Bacillus megaterium and Staphylococcus aureus) bacterial strains. Efforts have been made to understand the underlying molecular mechanism of such antibacterial actions. The effect of the core-shell nanostructures on Gram negative strains was found to be better than that observed for silver nanoparticles. The minimum inhibitory concentration (MIC) values of these nanostructures were found to be considerably lowe...

Energy Technology Data Exchange (ETDEWEB)

The refractory nature and high ductility of body centered cubic (bcc) phase tantalum makes it a suitable material for corrosion- and wear-resistant coatings on surfaces which are subjected to high stresses and harsh chemical and erosive environments. Sputter deposition can produce thick tantalum films but is prone to forming the brittle tetragonal beta phase of this material. Efforts aimed at forming thick bcc phase tantalum coatings in both flat plate and cylindrical geometries by high-rate triode sputtering methods are discussed. In addition to substrate temperature, the bcc-to-beta phase ratio in sputtered tantalum coatings is shown to be sensitive to other substrate surface effects.

Energy Technology Data Exchange (ETDEWEB)

In the early days of Moessbauer spectroscopy, it was demonstrated that coherent scattering of photons emitted by a Moessbauer source can be observed. In spite of the fact that scattering experiments could give information not accessible by the absorption method, they are not widely used. The reasons for this are, on the one hand, experimental difficulties, and on the other hand, the form of the samples, which should be large single crystals in most cases. In this work, we present a Moessbauer diffraction measurement on polycrystalline bcc iron where these problems have been overcome. We demonstrate that using the kinematical theory of gamma-ray diffraction, useful information on the relative orientation of the crystallographic axis to the hyperfine field directions can be subtracted. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The physics and technology of a new class of efficient composite piezoelectrics are described. This material combines nanostructured and micropiezoelectric matrix composites. They consist of a polymer matrix, an insulating nanodimensional phase, and a microdimensional piezoelectric phase. It is shown that the nanostructuring of the near-surface region of polymer-PZT piezoelectric composites greatly improves their piezoelectric, mechanical, and electromechanical characteristics. A plausible mechanism underlying this effect is suggested.

International Nuclear Information System (INIS)

A scalar-relativistic procedure for calculating the valence-electron contribution to the total energy of bulk and thin-film solids has been developed and applied to the fcc and bcc phases of the group-VIB transition elements Cr, Mo, and W. This approach, which is based on the linear augmented-plane-wave method and local-density-functional theory, contains no shape approximations for either the charge density or potential. The formulation adopts a rigid-core approximation and incorporates an exact treatment of the core-charge tails that extend beyond the muffin-tin spheres. The application of this procedure to bcc Cr, Mo, and W yields calculated lattice parameters and bulk moduli that are in good (Cr) to excellent (Mo and W) agreement with experiment. The present calculated properties also agree quite well with the results of previous calculations involving a variety of band-structure methods. The calculated fcc-bcc energy ...

International Nuclear Information System (INIS)

Calculations in "7Li have been carried out for the differential coherent elastic scattering cross-section of thermal neutrons at a fixed scattering angle #theta#_0(148"o) and varying the energy of incident neutrons (or corresponding d-spacings). The results are reported, as variations of the ratio #SIGMA#_0"c"o"h (#theta#_0, d)/#SIGMA#_0"c"o"h (#theta#_0) with d-spacing, at atmospheric pressure and at two temperatures, 80 and 20 K. The calculations at 80 K correspond to BCC lithium whereas at 20 K all the possible crystallographic structures of polytype lithium (BCC, 9R, HCP and FCC) were considered. On comparing our results with the time-of-flight (TOF) measurements of Berliner et al. (Physical Review, B40, 12086, 1989) we find that up to 80 K lithium-7 does not undergo any martenistic transformation whereas the structural state at 20 K can be described by the co-existence of the original BCC phase with 9R, HCP and FCC ...

International Nuclear Information System (INIS)

We have calculated the electronic structure of Eu for the bcc, hcp, and fcc crystal structures for volumes near equilibrium up to a calculated 90 GPa pressure using the augmented-plane-wave method in the local-density approximation. The frozen-core approximation was used with a semi-empirical shift of the f-states energies in the radial Schroedinger equation to move the occupied 4f valence states below the #GAMMA#_1 energy and into the core. This shift of the highly localized f-states yields the correct europium phase ordering with lattice parameters and bulk moduli in good agreement with experimental data. The calculated superconductivity properties under pressure for the bcc and hcp structures are also found to agree with and follow a T_c trend similar to recent measurement by Debessai et al.

International Nuclear Information System (INIS)

... NOU TsIPK; Obninsk (Russian Federation) 978-5-85855-125-6 208 p.

UK PubMed Central (United Kingdom)

The treatment of brain disorders is one of the greatest challenges in drug delivery because of a variety of main barriers in effective drug transport and maintaining therapeutic concentrations in the...Full Text Available

International Nuclear Information System (INIS)

A study of the thin gold film growth, during the deposition on glass substrate under UHV conditions at low temperatures, is presented. The complementary methods, the atomic force microscopy and grazing incidence x-ray reflectometry, are used for the research. It is shown that due to variation of the time of deposition from 2 to 50 min different kinds of thin Au films nanostructures are obtained: from discontinuous films consisting of isolated islands, via formation of the chains of islands, up to continuous films. (author)

International Nuclear Information System (INIS)

Structure of ferrite in drawn pearlitic steel containing 0.9 mass% C was investigated with X-ray diffraction technique using synchrotron radiation. In the detailed analysis of diffraction peaks of ferrite during the drawing process, it was experimentally revealed that the transformation of ferrite from bcc to bct due to the supersaturation of carbon in ferrite of heavily drawn pearlitic steel.

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately estimates the tensile ...

Energy Technology Data Exchange (ETDEWEB)

A single crystalline ternary nanostructure having the formula A.sub.xB.sub.yO.sub.z, wherein x ranges from 0.25 to 24, and y ranges from 1.5 to 40, and wherein A and B are independently selected from the group consisting of Ag, Al, As, Au, B, Ba, Br, Ca, Cd, Ce, Cl, Cm, Co, Cr, Cs, Cu, Dy, Er, Eu, F, Fe, Ga, Gd, Ge, Hf, Ho, I, In, Ir, K, La, Li, Lu, Mg, Mn, Mo, Na, Nb, Nd, Ni, Os, P, Pb, Pd, Pr, Pt, Rb, Re, Rh, Ru, S, Sb, Sc, Se, Si, Sm, Sn, Sr, Ta, Tb, Tc, Te, Ti, Tl, Tm, U, V, W, Y, Yb, and Zn, wherein the nanostructure is at least 95% free of defects and/or dislocations.

International Nuclear Information System (INIS)

A single plasma process involving three consecutive steps has been developed for producing high gas flow catalytic nanostructures on the electrodes of proton exchange membrane (PEM) fuel cells (FC). Using a high density helicon radio frequency (13.56 MHz) plasma, nickel is sputtered onto a porous carbon support. Changing the background gas from argon to methane/hydrogen allowed 2 ?m long, 37 nm diameter carbon nanofibres (CNFs) to be grown by diffusion through the nickel clusters in a 'tip growth' mechanism at the relatively low temperature of 400 deg. C. The third step involves plasma sputtering of platinum onto the CNFs, resulting in nanoclusters (3-8 nm) being formed on the periphery of the CNFs. Four FC cathodes were synthesized on carbon paper and PTFE/carbon loaded cloth (known as gas diffusion layer, GDL), both with and without CNFs, with the Pt/CNFs nanostructures grown on PTFE/carbon loaded cloth having the best FC performances. ...

International Nuclear Information System (INIS)

A mass separated focused ion beam (FIB) is a very useful tool to fabricate nanostructures by writing implantation within an ion beam synthesis process. In these investigations the IMSA-OrsayPhysics FIB, equipped with a Co_3_6Nd_6_4 alloy liquid metal ion source, was applied. Si(100) and (111) wafers were implanted with 60 keV Co"+"+ ions in the dose range of 2 . 10"1"6 to 2 . 10"1"7 cm"-"2. Implantation parameters were investigated, like pixel dwell time, relaxation time (time between two cycles), dose rate as well as the pixel overlapping factor. The subsequent annealing was done in a two step process, namely 600 deg. C for 60 min and 1000 deg. C for 30 min in a N_2 ambient. The results obtained by SEM investigations in terms of continuous nanowire structures following the direction and interrupted CoSi_2 pattern in the direction show a clear dependence on the time scale as well as the scanning mode of the irradiation. Structure sizes as small as 10 nm are ...

Energy Technology Data Exchange (ETDEWEB)

The magnetization of ultrathin bcc Fe films (two and three monolayers) on MgO was measured and compared with the behavior predicted for a two-dimensional ferromagnet. The experiment indicated that no hysteresis was present in the magnetization. Instead, the magnetization at low temperature was affected by a marked field cooling effect. These observations lead to the conclusion that films of Fe on MgO of such thickness exhibit superparamagnetic behavior as if they were not entirely continuous. In contrast, films thicker than five monolayers exhibit a magnetic response close to that of bulk iron.

International Nuclear Information System (INIS)

The evolution of metallic substance atomic structure is studied on temperature variation including crystal heating up to melting points, a crystal- liquid phase transition and initiation of a high-density liquid specific structure. It is marked that heat induced changes of simple metal structure can be described as changes around a natural elementary cell which is common for both a crystal and a liquid and consists of a central atom and Z_1 atoms of the first coordination sphere. On this basis the vacancy model of melting is verified. Concentrations of melting vacancies are determined by coordination numbers in the form of Z_1/(1+Z_1)"2 which are the same for both a crystal and a natural elementary cell. The size of natural elementary cells is in an agreement with that of the coordination sphere featured in the liquid and phase transition statistical theory. Calculated data are given for a number of metals, Cs, Eu, Ni, V included

British Library Electronic Table of Contents (United Kingdom)

Modifications of the structure and mechanical properties in LiF crystals irradiated with MeV-energy Au ions have been studied using nanoindentation, atomic force microscopy and optical spectroscopy. The nanostructuring of crystals under a high-fluence irradiation (above 1013 ions/cm2)?was?observed. Nanoindentation tests show a strong ion-induced increase of hardness (up?to 150?200%), which is related to the high volume concentration of complex color centers, defect aggregates, dislocation loops and grain boundaries acting as strong barriers for dislocations. From the?depth profiling of the hardness and energy loss it follows that both nuclear and electronic stopping mechanisms of MeV Au ions contribute to the creation of damage and hardening. Whereas the electronic stopping is dominating i...

British Library Electronic Table of Contents (United Kingdom)

The aim of this study was to develop a nanostructured Nb2O5-natural hydroxyapatite bulk composite to serve as an alternative biocompatible bulk material for implants. A set of samples of hydroxyapatite from fish bones with different concentrations of Nb2O5 were designed. They were prepared through a milling process, compacted under different pressures (350, 450, 550 and 650MPa) and sintered in air atmosphere at 1000^oC for 1h. The results revealed that the prepared composites presented strong interactions between the two elements and showed improvement in the sinterability with significant densification and microstructure changes, suggesting that they are promising for implants meant to replace bone tissues.

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline and nanostructured materials offer unique microstructure-dependent properties that are superior to coarse-grained materials. These materials have been shown to have very high hardness, strength, and wear resistance. However, most current methods of producing nanostructured materials in weapons-relevant materials create powdered metal that must be consolidated into bulk form to be useful. Conventional consolidation methods are not appropriate due to the need to maintain the nanocrystalline structure. This research investigated new ways of creating nanocrystalline material, new methods of consolidating nanocrystalline material, and an analysis of these different methods of creation and consolidation to evaluate their applicability to mesoscale weapons applications where part features are often under 100 {micro}m wide and the material's microstructure must be very small to give homogeneous properties across the feature.

International Nuclear Information System (INIS)

Full text: It was recently-established for hexagonal barium ferrite-industrially important magnetically hard material that refinement of the crystallite dimensions into the nanoscale regime, typically #<=# 10 nm, leads after heat treatment at temperatures 800-1000 deg C to significant coercivity increase of up to 6.5 kOe (#approx#3-4 times) with saturation magnetisation values of 50-55 emu/g (#approx#95% of bulk at room temperature). High-energy mechanochemical processing has been applied to prepare nanostructural (nanocrystalline-amorphous) composites. High resolution electron microscopy studies reveal that the enhancement of the final magnetic properties was due to formation of magnetically noninteracting #approx#l,#mu#m Ba-ferrite particles with 5-10 nm amorphous surface layer - depending on annealing parameters. Similar situation was established also for ball milled strontium ferrite (SrFe_1_2O_1_9) powders where short annealing 4 h at 1000 deg C produced ...

International Nuclear Information System (INIS)

The optical, electromagnetic and mechanical properties of thin films (TFs) are directly correlated to their morphology at the nanoscale. This, in concert with the fact that new deposition techniques are enabling the growth of thin films with very complex morphologies, there is an increasing interest in model-based simulation (MBS) for the design of engineering structures (including nanostructures), and increasing computer speeds are beginning to make MBS an effective design tool capable of bridging the nanoscale with the continuum scale, has made it increasingly important to understand how the nanostructure of a thin film impacts its properties at all length scales. The authors have developed the capability to determine the mechanical properties of thin films with amorphous nanostructure by combining molecular dynamics, i.e., position of particles (e.g., atoms or molecules) and their interatomic potential(s), with continuum ...

Science.gov (United States)

In this Communication, we report the fabrication of well-crystallized rutile-phase TiO2 hollow spheres using potassium titanium oxalate as the precursor. The spheres exhibited unique three-dimensional hierarchical architectures and demonstrated a significantly improved photocatalytic performance. The synthetic strategy used in this process represents a general approach and therefore may contribute to the formation mechanisms of hollow nanostructures. PMID:16634578

International Nuclear Information System (INIS)

The constituent phases and associated deformed microstructure of the quenched Ti-xNb-(0.5-1.5) at.% Si alloy consisting of non-cytotoxicity elements, where x = 24-30 at.%, were investigated to provide pseudoelasticity for biomedical and sensor applications. Optical microscopy revealed that stress-induced martensitic transformation takes place during the deformation in the present alloys. It is confirmed from the X-ray diffraction results of the deformed specimens that the crystal structure of the stress-induced martensite phase is the orthorhombic so-called #alpha#'' structure. Within the alloys having #beta#(bcc) phase studied Nb-poor region appeared to exhibit a dominant behavior for stress-induced martensitic transformation than Nb-rich region. This result suggests that metastable #beta# phase is superior to stable #beta# phase for the occurrence of stress-induced martensitic transformation in the present alloy system.

International Nuclear Information System (INIS)

Initial rates of resistivity-measured low-temperature damage production by fission-spectrum fast neutrons have been determined for 14 metals in the same very well characterized irradiation facility. Six of these metals were fcc, 5 bcc, and 3 hcp. Most were of quite high purity. Observed damage rates, after correction for all known extraneous resistivity-producing effects, were compared with rates predicted by the damage calculation code RECOIL, using parameters chosen from the literature. These parameters, effective displacement threshold energy, E/sub d/, and Frenkel-pair resistivity, rho/sub F/, were in many cases only best estimates, the further refinement of which may be aided by the present results. Damage efficiencies (measured/predicted rates) follow the same trends by crystal classes as seen in other fast-neutron studies.

International Nuclear Information System (INIS)

The EXAFS-study (Fe, Sn and Ge K-edges) of disordered by mechanical activation binary supersaturated nanocrystalline solid solutions Fe-Al, Fe-Ge, Fe-Sn and Fe-Si is presented. The EXAFS-spectra are processed by solving the inverse binary problem, using the EXAFS-spectrum of the Fe K-edge only or combining the EXAFS-spectra on two K-edges, Fe and Ge or Fe and Sn. The parameters of partial correlation functions indicate chemical short-range ordering, high local static distortions in the lattice, increasing with metalloid content. The macrostructure of other type is forming through an initial, 'local' stage within the bcc lattice.

British Library Electronic Table of Contents (United Kingdom)

Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal firms and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in the advanced DEA linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of tot...

Energy Technology Data Exchange (ETDEWEB)

We have developed a flexible radioactive polyurethane patch incorporating {beta}-emitting radionuclide (166Ho) to treat malignant skin lesions. We covered the tumor surface (n=133) with the radioactive patch for 33.58 {+-} 5.33 minutes. Radiation dose delivered was 35 Gy for Bowen's disease (n=78), Kaposi sarcoma (n=25), actinic keratosis (n=5), and 50 Gy for BCC (n=17) and squamous carcinoma (n=8). Complete response was observed in 91.7% after the first therapeutic trial, 96.2% after 2nd and 97.7% after 4th trial with excellent cosmetic outcome for 31.15{+-}13.88 months of follow-up. Radioactive patch therapy is effective for superficial skin cancers that are impractical for surgery.

Energy Technology Data Exchange (ETDEWEB)

The investigated hybrid nanocomposite consists of a porous silicon template with electrochemically embedded Ni or Co nanostructures and offers magnetic characteristics which can be tailored by the electrochemical process parameters during fabrication. A twofold magnetic behaviour can be observed, a first one due to the spinmagnetism at magnetic fields below the saturation magnetization of the deposited metals and a second non-saturating term at higher fields (>1 T up to 7 T) above the saturation magnetization. In case of Ni deposited within the pores this non-saturating term shows a paramagnetic characteristic and follows exactly the Curie-Weiss law, whereas for Co/porous silicon samples the temperature dependent magnetization shows some deviations from the Curie Weiss law. In this high field region a difference in the temperature dependence between Ni and Co is observed whereas the non-saturating term does not depend on the geometry of the embedded ...

British Library Electronic Table of Contents (United Kingdom)

Here in the present paper, we report on growth of stoichiometric and nonstoichiometric nanostructured heterojunction solar cell of CdS/CuInSXSe2-X varying X from 0 to 2 in the interval of 0.5 using cost effective, simple, chemical ion exchange method at room temperature on ITO glass substrate. The as-grown varying composition solar cells annealed at 200degreeC in air and characterized for structural, compositional, optical and illumination studies. The X-ray diffraction pattern obtained from CdS/CuInSXSe2-X solar cell confirms the formation of CuInSe2, CuInS0.5Se1.5, CuInS1Se1, CuInS1.5Se0.5 and CuInS2 phases having tetragonal structure with varying crystallite size from 19, 19.37, 28, 33 and 20nm respectively. The energy dispersive X-ray analysis (EDAX) confirms the expected elemental com...

International Nuclear Information System (INIS)

Focused Ion Beam (FIB) milling is a powerful tool to produce ordered magnetic nanostructures. However, it is impossible to produce out-of-plane magnetized nanoscale structures from multilayer films by direct FIB writing. Co/Pt multilayers exhibit an out-of-plane easy axis due to strong perpendicular interface anisotropy. The interface contribution is known to be very sensitive to high energy ion irradiation. In case of 30 keV Ga ions it needs less than one ion per 100 surface atoms to destroy the perpendicular interface anisotropy. We demonstrate how this problem can be overcome by milling a Co/Pt multilayer, which has been deposited on a SiN membrane, from the rear side, through the SiN. The effect of the ions is determined as a function of applied dose utilizing the domain structure imaged by soft X-ray holography. When the magnetic material is removed we find only a very narrow range of destruction around the holes in contrast to the observations when milling ...

International Nuclear Information System (INIS)

In the present work the hydrogen desorption properties of nanostructured magnesium hydride (MgH2) synthesized by controlled reactive mechanical milling (CRMM) of elemental Mg powder under hydrogen are investigated. A profound effect of the particle size of synthesized MgH2 hydride on its hydrogen desorption characteristics measured by differential scanning calorimetery (DSC) has been found. All synthesized MgH2 powders are characterized by a double hydrogen desorption peak. Furthermore, below a certain threshold particle size the DSC desorption temperature of the peak doublet starts decreasing rapidly with decreasing of the mean hydride powder particle size (expressed as equivalent circle diameter-ECD). In contrast, the nanograin (crystallite) size of MgH2 does not seem to have apparent effect on the DSC desorption temperature. It is also observed that for powder particles smaller than some threshold value, X-ray diffraction shows the presence of two polymorphic ...

International Nuclear Information System (INIS)

In the present paper it is assumed that above a limiting value of fission fluency (burn-up) a more intensive process of irradiation introduced chemical interaction occurs. A significant part of fission gas product is thus expected to be chemically bounded in the matrix of UO_2 fuel. The fission gas atoms substituting, for example, uranium atoms in the crystallographic lattice can form weak facets. At a certain saturation condition, division of the grains can occur at the weak facets and the increase in fission-gas products release may be expected. The fact that the process of grain division for high burn-ups (70-80 MWd/kgU) forms an extremely fine structure up to the temperature as high as 1100 "oC and simultaneously the observed decreases in fission gas concentration in the fuel supports this concept. The analysis of fission gas concentration change due to the formation of nanostructures in UO_2 fuel at high burn-ups in terms of total surface area change in a ...

CERN Document Server

material, and that these magnetic properties vary systematically with the diameter of the spherical pores within the films. A new oscillation effect has been observed for the coercivity of macroporous Ni sub 8 sub 0 Fe sub 2 sub 0 film with different pore layer thickness. sphere templates, the resulting films show well-formed, regular, two- and three-dimensional macroporous networks consisting of spherical pores arranged in a highly ordered face centred cubic (fee) structure. The spherical voids are interconnected by a series of smaller windows that form an open porous structure embedded in the material framework. The diameter of the spherical pores can be precisely changed over the range from 200 to 1000 nm by changing the diameter of the latex spheres used to form the templates. The resulting macroporous material structures are robust, self-supported, dense, polycrystalline, uniform and free from filling defects and contamination or problems caused by shrinkage during processing. The ...

Energy Technology Data Exchange (ETDEWEB)

A model for the structural relaxation of grain boundaries (GBs) in nanostructured materials (NSMs) by diffusion-accommodated rigid body translations along GBs is proposed. The model is based on the results of recent computer simulations that have demonstrated that the GBs in NSMs retain a high-energy structure with random translational states due to severe geometrical constraints applied from neighboring grains (J. Appl. Phys. 78 (1995) 847; Scripta Metall. Mater. 33 (1995) 1245). The shear stresses within a GB caused by non-optimized rigid-body translations (RBTs) can be accommodated by diffusive flow of atoms along a GB. This mechanism is particularly important for low-angle and vicinal GBs, the energy of which noticeably depends on the rigid body translations. At moderate and high temperatures the model yields relaxation times that are very short and therefore GBs in NSMs can attain an equilibrium structure with optimized rigid body translations. In contrast, at ...

International Nuclear Information System (INIS)

HgTe rod-shape composed of crystalline particles has been prepared by a hydrothermal method, and characterized by means of X-ray powder diffraction (XRD), scanning electron microscopy (SEM), and transition electron microscopy (TEM). The effects of capping agents, reductants, reaction temperatures, and reaction times on crystal structures and shapes of HgTe have been investigated. The results showed that the CTAB as capping agent plays a crucial role in the hydrothermal process. The synthesis procedure is simple and uses less toxic reagents than the previously reported methods.

Energy Technology Data Exchange (ETDEWEB)

We investigate the formation of nanostructures in 2D strained alloys on face centered cubic (111) surfaces by means of equilibrium Monte Carlo simulations. In the framework of an off-lattice model, we consider one monolayer of two bulk-immiscible adsorbates A and B with negative and positive misfit relative to the substrate, respectively. Simulations show that the adsorbates partly self-organize into island or stripe-like patterns. We show how these structures depend on the relative misfits, interaction, and concentration of components. The morphology is quite different for phase separation and intermixing regimes.

International Nuclear Information System (INIS)

Formation of the soft magnetic nanostructure in amorphous Fe_1_4Ni_4_0Zr_7B_1_2 alloy due to heat treatment is studied by the Moessbauer, differential scanning calorimetry, and X-ray diffraction techniques. Annealing at temperatures 520-580 "oC leads to the formation of extremely soft nanocrystalline alloy as revealed by the rf-Moessbauer measurements. The superparamagnetic behaviour was observed for the alloy annealed at 620-640 "oC. At higher annealing temperatures good soft magnetic properties deteriorate. (author)

International Nuclear Information System (INIS)

Several recent experiments on micro- (or nano-) structured samples of ferromagnetic materials are introduced. Magnetization reversal phenomena are investigated on submicron wire samples of trilayer structure using the giant magnetoresistance effect. Domain wall movements are sensitively monitored by resistivity measurements and the velocity of propagation is determined. The contribution of domain wall to the resistivity is argued from the results on artificially designed samples of a spring-magnet system. In circular dots of permalloy, the existence of vortex magnetization is confirmed and the reversal of the vortex core magnetization is studied from magnetic force microscopy measurements. (author)

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Energy and environment are two major concerns in our modern society due to the coming shortage in fossil energy sources and the growing of greenhouse gas emissions. The challenge for the coming years is to discover new energy resources and to develop devices that are compatible with a sustainable development and generate few (or zero) emission. One of these devices is the fuel cell feed by hydrogen, whose application fields are very large. In particular, the proton exchange membrane fuel cell (PEMFC) is the most realistic device for automotive application. However, hydrogen storage remains one of the most important challenges regarding its development. Although different techniques are available for storing hydrogen, no ideal solution has been found yet. Compression needs elaborated tanks in shape for supporting high pressures, liquefaction requires an expensive hydrogen cooling and adapted tanks. Chemical storage by hydrides imposes heavy devices. A ...

Energy Technology Data Exchange (ETDEWEB)

Nanoparticles represent versatile building blocks in material science and nanotechnology. Thereby, the defined assembly of nanostructures (13 and 56 nm in diameter, respectively) is of significant importance. Short DNA sequences can be bound to the nanoparticle surface thus enabling highly specific DNA hybridization-driven events that direct the formation of nanoparticle constructs.In this paper, examples for the defined formation of gold nanoparticle constructs are demonstrated. In addition, gold-silver core-shell nanoparticles are introduced as further building blocks for the hybridization-controlled formation of nanoparticle constructs.

International Nuclear Information System (INIS)

The anodic reaction kinetics and interfacial mass transport of a direct polymer electrolyte membrane formic acid fuel cell have been investigated in an all solid-state electrochemical cell using a highly active nanostructured palladium-gold alloy microelectrode as an in situ probe. Well-defined 'S-shaped' steady-state cyclic voltammograms exhibiting current-rising region at lower overpotentials and limiting current region at higher overpotentials have been first obtained for the electrochemical oxidation of formic acid at varying temperature. The 'S-shaped' steady state polarization curves and chronoamperometric curves enable convenient measurements of the anodic reaction kinetics and interfacial mass transport of formic acid under real polymer electrolyte membrane conditions. It is encouragingly found that formic acid can be directly oxidized to CO2 with the first electron transfer being the likely rate-determining step and the formation of surface poison can be ...

International Nuclear Information System (INIS)

Kinetic Monte Carlo (KMC) computer simulations are performed to determine the kinetics of SIA cluster 'clouds' in the vicinity of edge dislocations. The simulations include elastic interactions amongst SIA clusters, and between clusters and dislocations. Results of KMC simulations that describe the formation of 'SIA clouds' during neutron irradiation of bcc Fe and the corresponding evolution kinetics are presented, and the size and spatial distribution of SIA clusters in the cloud region are studied for a variety of neutron displacement damage dose levels. We then investigate the collective spatio-temporal dynamics of SIA clusters in the presence of internal elastic fields generated by static and mobile dislocations. The main features of the investigations are: (1) determination of the kinetics and spatial extent of defect clouds near static dislocations; (2) assessment of the influence of localized patches of SIA clouds on the pinning-depinning motion of ...

International Nuclear Information System (INIS)

Three types of titanium hydrides have been reported: #delta#, #epsilon# and #gamma# hydrides. The #delta# hydride forms in the composition range from TiH/sub 1.5/ to TiH/sub 1.99/ and has a CaF/sub 2/ structure with metal atoms on an fcc lattice and hydrogen atoms randomly occupying tetrahedral interstitial sites. At higher hydrogen concentrations, TiH/sub 2/, the fct (c/a # #epsilon# transformation is apparently diffusionless, similar to that operating in the cubic/tetragonal transformation in zirconium hydride. The metastable fct #gamma# hydride having a c/a value of 1.09 or 1.12 forms from solid solutions of hydrogen in the hcp #alpha# matrix. While the titanium hydride precipitation in #alpha#-Ti and its alloys has attracted extensive investigation, hydride formation in bcc #beta#-Ti alloys has rarely been studied because they have not been thought to be liable to hydride formation. This paper shows conclusive evidence for the fcc #delta# hydride phase ...

International Nuclear Information System (INIS)

The crystallography of #alpha#(hcp) precipitates formed on the #beta#(bcc) matrix grain boundaries has been studied with transmission electron microscopy (TEM) in a Ti-15V-3Cr-3Sn-3Al alloy. The #alpha# precipitates have a near-Burgers orientation relationship with respect to at least one of the adjacent #beta# grains. Among the possible 12 variants in this orientation relationship, the variant that [11 bar 20]_#alpha# is parallel to the _#beta# closest to the grain boundary plane tends to be preferred by the #alpha# precipitates. Additionally, further variant selections are made so as to minimize the deviation of orientation relationship with respect to the ''opposite'' #beta# grain from the Burgers one. Such rules in variant selection often result in the formation of precipitates with a single variant at a planar grain boundary. Prior small deformation of #beta# matrix changes the variant of #alpha# precipitates at the deformed portion of grain boundary. It is ...

Energy Technology Data Exchange (ETDEWEB)

Continually rising energy prices in global markets highlights a serious concern about the need to improve energy efficiency and the efficiency in the energy sector in many countries. China, as one of the fastest growing countries in the world and the largest coal producer, has high coal consumption but a low recovery rate of coal utilization. Coal efficiency and the efficiency in coal industry have therefore attracted a great deal of attention from Chinese policy makers, coal companies and academics. This study attempts to compare the relative technical efficiency performance of listed coal mining companies in China and the US using CCR and BCC models in advanced data envelopment analysis (DEA) linear programming. The results show that the level of relative efficiency in Chinese coal mining enterprises, regardless of total technical efficiency or decomposed pure technical and scale efficiency, is much lower than in American coal firms. The study also highlights the ...

British Library Electronic Table of Contents (United Kingdom)

As portable electronics become more advanced and alternative energy demands become more prevalent, the development of advanced energy storage technologies is becoming ever more critical in today's society. In order to develop higher power and energy density batteries, innovative electrode materials that provide increased storage capacity, greater rate capabilities, and good cyclability must be developed. Nanostructured materials are gaining increased attention because of their potential to mitigate current electrode limitations. Here we report on the use of vertically aligned multi-walled carbon nanotubes (VA-MWNTs) as the active electrode material in lithium-ion batteries. At low specific currents, these VA-MWNTs have shown high reversible specific capacities (up to 782mAhg^-^1 at 57mAg^-...

British Library Electronic Table of Contents (United Kingdom)

The light-emitting properties of cubic silicon carbide films grown by vacuum vapor phase epitaxy on Si(100) and Si(111) substrates under conditions of decreased growth temperatures (T gr ? 900?700?C) have been discussed. Structural investigations have revealed a nanocrystalline structure and, simultaneously, a homogeneity of the phase composition of the grown 3C-SiC films. Photoluminescence spectra of these structures under excitation of the electronic subsystem by a helium-cadmium laser (?excit = 325 nm) are characterized by a rather intense luminescence band with the maximum shifted toward the ultraviolet (?3 eV) region of the spectral range. It has been found that the integral curve of photoluminescence at low temperatures of measurements is split into a set of Lorentzian components. Th...

Energy Technology Data Exchange (ETDEWEB)

We report the simultaneous formation of self-assembled surface ripples in Cd{sub 2}Nb{sub 2}O{sub 7} pyrochlore caused by focused ion beam (FIB) patterning and uniformly distributed metallic nanodots induced by phase decomposition under ion bombardment. The characteristic wavelength of the surface ripples is controllable from the nm to the sub-{micro}m scale. High-density Cd metallic nanoparticles, {approx} 5 nm, formed and the distribution of nanoparticles is consistent with the morphological characteristics of the ripple pattern. This approach provides a means of fabricating surface nanostructure with various patterns and a controllable particle size and distribution by combining ion beam-induced phase decomposition with high-precision FIB patterning.

Energy Technology Data Exchange (ETDEWEB)

Thin films of sodium montmorillonite clay and cationic polyacrylamide were grown on a polyethylene terephthalate film using layer-by-layer assembly. After 30 clay-polymer layers are deposited, with a thickness of 571 nm, the resulting transparent film has an oxygen transmission rate (OTR) below the detection limit of commercial instrumentation (< 0.005 cc/m{sup 2}/day/atm). This low OTR, which is unprecedented for a clay-filled polymer composite, is believed to be due to a brick wall nanostructure comprised of completely exfoliated clay in polymeric mortar. With an optical transparency greater than 90% and potential for microwaveability, this thin composite is a good candidate for foil replacement in food packaging and may also be useful for flexible electronics packaging.

CERN Document Server

The controlled growth of nanowires (NWs) with dimensions comparable to the Fermi wavelengths of the charge carriers allows fundamental investigations of quantum confinement phenomena. Here, we present studies of proximity-induced superconductivity in undoped Ge/Si core/shell NW heterostructures contacted by superconducting leads. By using a top gate electrode to modulate the carrier density in the NW, the critical supercurrent can be tuned from zero to greater than 100 nA. Furthermore, discrete sub-bands form in the NW due to confinement in the radial direction, which results in stepwise increases in the critical current as a function of gate voltage. Transport measurements on these superconductor-NW-superconductor devices reveal high-order (n = 25) resonant multiple Andreev reflections, indicating that the NW channel is smooth and the charge transport is highly coherent. The ability to create and control coherent superconducting ordered states in semiconductor-superconductor hybrid ...

British Library Electronic Table of Contents (United Kingdom)

To improve the friction and wear behavior of carbon fabric reinforced polymer composites (CFRP), nano-SiO2 was deposited on the fabric surface. The friction and wear behavior of the resulting composites were investigated on a model ring-on-block test rig. Experimental results revealed that fiber surface treatment contributed to largely improve the tribological properties of the CFRP composites. Scanning electron microscope (SEM) investigation showed that the worn surface of the surface modified CFRP composite was smoother under given load and sliding rate. Field emission scanning electron microscopy (FESEM), FTIR and X-ray photoelectron spectroscopy (XPS) studies of the carbon fiber surface showed that nanostructured Sio2 thin film can be obtained by SiO2 sols deposition, which improved th...

International Nuclear Information System (INIS)

One-dimensional core-shell polymer nanowires offer many advantages and great potential for many different applications. In this paper we introduce a highly versatile two-step template wetting process to fabricate two-component core-shell polymer nanowires with controllable shell thickness. PLLA and PMMA were chosen as model polymers to demonstrate the feasibility of this process. Solution wetting with different concentrations of polymer solutions was used to fabricate the shell layer and melt wetting was used to fill the shell with the core polymer. The shell thickness was analyzed as a function of the polymer solution concentration and viscosity, and the core-shell morphology was observed with TEM. This paper demonstrates the feasibility of fabricating polymer core-shell nanostructures using our two-step template wetting process and opens the arena for optimization and future experiments with polymers that are desirable for specific applications.

Energy Technology Data Exchange (ETDEWEB)

Porous nanostructured LiFePO{sub 4} powder with a narrow particle size distribution (100-300nm) for high rate lithium-ion battery cathode application was obtained using an ethanol based sol-gel route employing lauric acid as a surfactant. The synthesized LiFePO{sub 4} powders comprised of agglomerates of crystallites <65nm in diameter exhibiting a specific surface area ranging from 8m{sup 2}g{sup -1} to 36m{sup 2}g{sup -1} depending on the absence or presence of the surfactant. The LiFePO{sub 4} obtained using lauric acid resulted in a specific capacity of 123mAhg{sup -1} and 157mAhg{sup -1} at discharge rates of 10C and 1C with less than 0.08% fade per cycle, respectively. Structural and microstructural characterization were performed using X-ray diffraction (XRD), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM) with energy dispersive X-ray (EDX) analysis while electronic conductivity and specific surface area ...

Energy Technology Data Exchange (ETDEWEB)

Nanoimprinting is a fast-growing technique for nanoscale patterning. One of the remaining issues in nanoimprinting is the removal of the residual layer after nanoimprinting. Traditionally the residual layer is removed by an oxygen reactive-ion etching (RIE) step. The need for a vacuum environment and dedicated equipment in this step lowers the throughput and increases the cost of the nanoimprinting process. It also prevents the possibility of patterning isolated functional polymers because oxygen RIE destroys the functional materials. In this work, novel nanoimprinting schemes are developed to nondestructively remove the residual layer in thermal nanoimprinting by solvent developing and dewetting. Combined with a transfer-bonding technique, three-dimensional polymer scaffolds are achieved. The techniques developed here eliminate the RIE step in thermal nanoimprinting and are compatible with roller nanoimprinting for large-scale patterning of polymer micro- or ...

British Library Electronic Table of Contents (United Kingdom)

Electrodeposition of tertiary alumina/yttria/carbon nanotube (Al2O3/Y2O3/CNT) nanocomposite by using pulsed current has been studied in this investigation. Coating process has been performed on nickel sulphate bath and nanostructure of obtained compound layer is examined with high precision figure analysis of SEM nanographs. The effects of process variables, i.e., Y2O3 concentration, treatment time, frequency and duty cycle, have been experimentally studied. Statistical methods are used to achieve the minimum of corrosion rate and average size of nanoparticles. Finally the contribution percentage of different effective factors is revealed and confirmation run shows the validity of obtained results. Also it has been revealed that by changing the size of nanoparticles, corrosion properties o...

International Nuclear Information System (INIS)

Focused ion beam (FIB) milling is a powerful and versatile tool for the maskless fabrication of structures and devices at micro- and nanometer scales. The approach is based on the milling and deposition capabilities of a focused ion beam, where the latter is achieved by ion-beam-assisted decomposition of a metalorganic gas precursor of the specific material that has to be deposited. The combination of FIB and scanning electron microscopy in the same unit (so-called dual-beam unit) further expands the capabilities of the approach by the possibility of performing electron-beam-assisted deposition and inspection. Permalloy nanowires with electrical contacts patterned by FIB-Pt deposition were prepared in the dual-beam unit. Various types of notches to pin magnetic domain walls were additionally fabricated by means of FIB. The fabrication parameters for a structural modification of the Permalloy structures without too strongly affecting the material properties were determined previously. ...

Energy Technology Data Exchange (ETDEWEB)

The optoelectronic and excitonic properties in a series of linear acenes are investigated using range-separated methods within time-dependent density functional theory (TDDFT). In these highly-conjugated systems, we find that the range-separated formalism provides a substantially improved description of excitation energies compared to conventional hybrid functionals, which surprisingly fail for the various low-lying valence transitions. Moreover, we find that even if the percentage of Hartree-Fock exchange in conventional hybrids is re-optimized to match wavefunction-based CC2 benchmark calculations, they still yield serious errors in excitation energy trends. Based on an analysis of electron-hole transition density matrices, we also show that conventional hybrid functionals overdelocalize excitons and underestimate quasiparticle energy gaps in the acene systems. The results of the present study emphasize the importance of a range-separated and asymptotically-correct contribution of ...

Energy Technology Data Exchange (ETDEWEB)

In ionic nanocrystals the cationic sub-lattice can be replaced with a different metal ion via a fast, simple, and reversible place-exchange, allowing post-synthetic modification of the composition of the nanocrystal, while preserving its size and shape. Here, we demonstrate for the first time that during such an exchange, the anionic framework of the crystal is preserved. When applied to nanoheterostructures, this phenomenon ensures that compositional interfaces within the heterostructure are conserved throughout the transformation. For instance, a morphology composed of a CdSe nanocrystal embedded in a CdS rod (CdSe/CdS) was exchanged to a PbSe/PbS nanorod via a Cu2Se/Cu2S structure. During every exchange cycle, the seed size and position within the nanorod were preserved, as evident by excitonic features, Z-contrast imaging, and elemental line-scans. Anionic framework conservation extends the domain of cation exchange to the design of more complex and unique ...

International Nuclear Information System (INIS)

The layer-by-layer (LBL) self-assembly has been extensively used as a simple and effective method for the preparation of polyelectrolyte multilayer films. In this work, we utilized this unique method to prepare polyimide precursor/layered double hydroxide (LDH) ultrathin films. Well-crystallized Co-Al-CO_3 LDH and subsequent anion exchanged Co-Al-NO_3 LDH were prepared and characterized by scanning electron microscopy and X-ray diffraction (XRD). By vigorous shaking of the as-prepared Co-Al-NO_3 LDH, positively charged and exfoliated LDH nanosheets were obtained. Atomic force microscopy and XRD investigations indicated the delamination of LDH nanosheets. The precursor of polyimide, poly(amic acid) tertiary amine salt (PAS) was prepared by the polycondensation of dianhydride and diamine, and subsequent amine salt formation. By using the LBL method, heterogeneous ultrathin films of PAS and LDH were prepared. The formation of the ordered nanostructured assemblies was ...

Energy Technology Data Exchange (ETDEWEB)

RNA interference has become a powerful biological tool over the last decade. In this study, a tetracycline-inducible shRNA vector system was designed for silencing CFP expression and delivered alongside the yfp marker gene into Chinese hamster ovary cells using impalefection on spatially indexed vertically aligned carbon nanofiber arrays (VACNFs). The VACNF architecture provided simultaneous delivery of multiple genes, subsequent adherence and proliferation of interfaced cells, and repeated monitoring of single cells over time. Following impalefection and tetracycline induction, 53.1% 10.4% of impalefected cells were fully silenced by the inducible CFP-silencing shRNA vector. Additionally, efficient CFP-silencing was observed in single cells among a population of cells that remained CFP-expressing. This effective transient expression system enables rapid analysis of gene silencing effects using RNAi in single cells and cell populations.

Environmental Research Database

Objectives1. To develop new photoactive materials and fabricate demonstration QD (quantum dot) solar cells. This will be achieved by:~%~1.1. Materials preparation and characterisation of QD/polymer systems~%~1.2. Optimising structures of QDs, nanorods and polymer for quantum yield and charge transfer~%~1.3 Fabricating demonstration QD/polymer solar cells and measuring power conversion efficiencies~%~2. To demonstrate multiexciton generation (MEG) and harvesting within nanostructured QDs. This will involv [continued...]DescriptionWidespread implementation of photovoltaic electricity to meet changing energy demands requires a step-change in the cost of photovoltaic power. This proposal assembles a consortium of chemists, physicists, materials scientists and electrical engineers from The University of Manchester and Imperial College London to address this need through the development of new low-cost, high-efficiency, demonstration solar cells for micro-generation.We ...

International Nuclear Information System (INIS)

Focused Ion Beams are an important approach for nanostructure fabrication in the semiconductor industry and material sciences. Applications in sputtering and ion induced deposition of materials are investigated. The IMSA FIB system equipped with the high resolution Orsay Physics CANION M31plus ion column with current densities up to 10 A/cm"2 including a gas injection system is applied. In this work the ion beam induced chemical vapour deposition of tungsten, wherefore tungsten hexacarbonyl as precursor gas is used for a first investigation. Conductive tungsten-nanowires with smallest cross-section upon a substrate of Si and SiO_2 are produced. The ion beam parameters of this focused ion beam system are optimized for the metal deposition. A short insight in the theory of layer nucleation and growth induced by the ion beam during the metal deposition is given. The layer quality is determined by Auger electron analysis which shows the components in atomic percent ...

International Nuclear Information System (INIS)

We report a study of the physical characteristics of the pillars of C, Pt and W grown by 10-30 keV Ga focused ion beam (FIB) as a function of Ga ion flux, and present a quantitative analysis of the elements using energy-dispersive analysis of X-rays (EDAX). All the FIB grown pillars exhibit a rough morphology with whisker like protrusions on the cylindrical surface and broadening of the base as compared to the nominal size. For a constant fluence, the height of the pillar initially increases and then reduces after going through a maximum as a function of ion flux in all the cases. The compositional analysis shows good metallic quality for Pt structures but reveals significant contamination of Ga in C and Ga and C in W structures at higher ion fluxes. Explanation to all these observations has been sought in the light of secondary ion and electron effects and the different processes involved which lead to the FIB induced deposition.

Energy Technology Data Exchange (ETDEWEB)

Both the sign and magnitude of residual stress can vary with the thickness of sputter deposited films. The origins of this behavior are not well understood. In this work, the authors consider the correlation between the residual stress behavior and the depth dependence of impurities in thin (2.5 nm--150 nm) sputtered Mo and Ta films. They also consider the effects of phase transformations and microstructural changes on the stress behavior. Films were deposited onto Si substrates with native oxide. The residual stress observed in the Mo films varied from highly compressive at 2.5 nm film thickness to {approximately}0 at 10 nm thickness. Ta films also exhibited a high compressive stress, which relaxed from highly compressive to tensile between 10 nm and 50 nm film thickness. Impurities in the films may originate from the sputtering targets, the background gases, and the substrate surfaces. Auger Electron Spectroscopy (AES) results showed the presence of O and C contamination near the ...

Energy Technology Data Exchange (ETDEWEB)

The shock-induced {alpha}(bcc){r_arrow}{var_epsilon}(hcp) transition in iron begins at 13 GPa on the Hugoniot. In the two-phase region above 13 GPa, the Hugoniot lies well above the equilibrium surface defined by G{sub {alpha}}=G{sub {var_epsilon}}, with G the Gibbs free energy. Also, the phase transition relaxation time {tau} is uncertain, with estimates ranging from {lt}50 ns to {approx}180 ns. Here we present an extensive study of these important aspects, metastability and dynamics, of the {alpha}-{var_epsilon} transition in iron. Our primary theoretical tools are (a) accurate theoretically based free energies for {alpha} and {var_epsilon} phases of iron and (b) accurate calculations of the wave evolution following planar impacts. We define metastable surfaces for forward and reverse transitions by the condition that the thermodynamic driving force G{sub {alpha}}{minus}G{sub {var_epsilon}} is just balanced by an opposing force resulting from elastic stresses, ...

International Nuclear Information System (INIS)

The projector augmented-wave (PAW) method was developed by Bloechl as a method to accurately and efficiently calculate the electronic structure of materials within the framework of density-functional theory. It contains the numerical advantages of pseudopotential calculations while retaining the physics of all-electron calculations, including the correct nodal behavior of the valence-electron wave functions and the ability to include upper core states in addition to valence states in the self-consistent iterations. It uses many of the same ideas developed by Vanderbilt in his open-quotes soft pseudopotentialclose quotes formalism and in earlier work by Bloechl in his open-quotes generalized separable potentials,close quotes and has been successfully demonstrated for several interesting materials. We have developed a version of the PAW formalism for general use in structural and dynamical studies of materials. In the present paper, we investigate the accuracy of this implementation in ...

International Nuclear Information System (INIS)

Radioactive "3"1Si was used as a marker to study metal silicide formation. Activity profiles in the silicides were measured by a combination of ion beam sputtering, radioactivity counting and Rutherford backscattering of charged nuclear particles. It was found that the metal is the diffusing species during Co_2Si, Pt_2Si, NiSi and PtSi formation, while silicon diffuses during CrSi_2, TiSi_2 and ZrSi_2 formation. Silicon was also found to be the diffusing species during second phase formation of CoSi from Co_2Si. However, in this case it was established that the silicon diffuses by a grain boundary and/or interstitial mechanism. Both the metal and silicon diffuse during Ni_2Si and Pd_2Si formation. In an attempt to interpret complex radioactivity profiles a computer program, simulating various diffusion mechanisms during both first and second phase silicide formation, was written. A numerical approach was used whereby silicide growth occurs in small increments and the concentration of ...

Energy Technology Data Exchange (ETDEWEB)

After pioneering work in the 1980s, plasma-based ion implantation (PBII) and plasma-based ion implantation and deposition (PBIID) can now be considered mature technologies for surface modification and thin film deposition. This review starts by looking at the historical development and recalling the basic ideas of PBII. Advantages and disadvantages are compared to conventional ion beam implantation and physical vapor deposition for PBII and PBIID, respectively, followed by a summary of the physics of sheath dynamics, plasma and pulse specifications, plasma diagnostics, and process modeling. The review moves on to technology considerations for plasma sources and process reactors. PBII surface modification and PBIID coatings are applied in a wide range of situations. They include the by-now traditional tribological applications of reducing wear and corrosion through the formation of hard, tough, smooth, low-friction and chemically inert phases and coatings, e.g. for engine components. ...

Science.gov (United States)

Silicon is an attractive alloy-type anode material because of its highest known capacity (4200 mAh/g). However, lithium insertion into and extraction from silicon are accompanied by a huge volume change, up to 300%, which induces a strong strain on silicon and causes pulverization and rapid capacity fading due to the loss of the electrical contact between part of silicon and current collector. Si nanostructures such as nanowires, which are chemically and electrically bonded to the current collector, can overcome the pulverization problem, however, the heavy metal current collectors in these systems are larger in weight than Si active material. Herein we report a novel anode structure free of heavy metal current collectors by integrating a flexible, conductive carbon nanotube (CNT) network into a Si anode. The composite film is free-standing and has a structure similar to the steel bar reinforced concrete, where the infiltrated CNT network functions as both ...

Energy Technology Data Exchange (ETDEWEB)

Chemical looping combustion (CLC) is an emerging technology for clean combustion. We have previously demonstrated that the embedding of metal nanoparticles into a nanostructured ceramic matrix can result in unusually active and sinter-resistant nanocomposite oxygen carrier materials for CLC which maintain high reactivity and high-temperature stability even when sulfur contaminated fuels are used in CLC. Here, we propose a novel process scheme for in situ desulfurization of syngas with simultaneous CO{sub 2}-capture in chemical looping combustion by using these robust nanocomposite oxygen carriers simultaneously as sulfur-capture materials. We found that a nanocomposite Cu-BHA carrier can indeed strongly reduce the H{sub 2}S concentration in the fuel reactor effluent. However, during the process the support matrix is also sulfidized and takes part in the redox process of CLC. This results in SO{sub 2} production during the reduction of the oxygen carrier and thus ...

Energy Technology Data Exchange (ETDEWEB)

The goal of the present work was to develop a new synthetic nanosystem for gene delivery. For this purpose, we chose two polysaccharides, hyaluronic acid (HA) and chitosan (CS), as the main components of the nanocarrier. Nanoparticles with different hyaluronate:chitosan (HA:CS) mass ratios (0.5:1 and 1:1) and different polymer molecular weights (hyaluronate 170 (HA) or <10 kDa (HAO) and chitosan 125 (CS) or 10-12 (CSO) kDa) could be obtained using an ionic crosslinking method. These nanoparticles were loaded with pDNA and characterized for their size, zeta potential and pDNA association efficiency. Moreover, their toxicity and ability to transfect the model plasmid pEGFP-C1 were evaluated in the cell line HEK 293, as well as their intracellular fate. The results showed that HA:CS nanoparticles have a small size in the range of 110-230 nm, a positive zeta potential of +10 to +32 mV and a very high pDNA association efficiency of 87-99% (w/w). On the other hand, nanoparticles ...

Energy Technology Data Exchange (ETDEWEB)

Since information has been regarded os a physical entity, the field of quantum information theory has blossomed. This brings novel applications, such as quantum computation. This field has attracted the attention of numerous researchers with backgrounds ranging from computer science, mathematics and engineering, to the physical sciences. Thus, we now have an interdisciplinary field where great efforts are being made in order to build devices that should allow for the processing of information at a quantum level, and also in the understanding of the complex structure of some physical processes at a more basic level. This thesis is devoted to the theoretical study of structures at the nanometer-scale, 'nanostructures', through physical processes that mainly involve the solid-state and quantum optics, in order to propose reliable schemes for the processing of quantum information. Initially, the main results of quantum information theory and quantum ...