Energy Technology Data Exchange (ETDEWEB)

This work covers three distinct aspects of deformation and fracture during indentations. In particular, we develop an approach to verification of nanoindentation induced film fracture in hard film/soft substrate systems; we examine the ability to perform these experiments in harsh environments; we investigate the methods by which the resulting deformation from indentation can be quantified and correlated to computational simulations, and we examine the onset of plasticity during indentation testing. First, nanoindentation was utilized to induce fracture of brittle thin oxide films on compliant substrates. During the indentation, a load is applied and the penetration depth is continuously measured. A sudden discontinuity, indicative of film fracture, was observed upon the loading portion of the load-depth curve. The mechanical properties of thermally grown oxide films on various substrates were ...

International Nuclear Information System (INIS)

Results of investigation on the effect of microstructure and deformation conditions (temperature and strain rate) on flow stress and critical strain in two phase #alpha# + #beta# titanium alloy Ti-6Al-5Mo-5V-1Cr-1Fe is presented in the paper. The alloy is deformed or torsional plastometer at temperature range 1073-1173 K and at the strain rate #epsilon# = 0.04-4.0 s"-"1. Sequential deformation at 1173 K at the strain rate of 0.4 s"-"1 was also performed with holding times in the range 1-100 s. The fraction of dynamically and metadynamically recrystallized #beta# phase was determined on the basis of results of sequential deformation test. Microstructure was examined using LM and TEM techniques. (author)

International Nuclear Information System (INIS)

The relationships of hydrogen alloyed #beta#-titanium alloy deformation behaviour to its microstructure and texture are investigated. It is shown that plasticity increases and strain induced texture changes at low hydrogen contents (0.1-0.2 mass %). Possible mechanisms responsible for specific features of #beta#-Ti alloy deformation are discussed. The study is made using alloy VT35 doped with hydrogen

Energy Technology Data Exchange (ETDEWEB)

Two aspects of the deformation behavior of magnesium sheets are the subject of this paper. First it will give a mechanical characterization of a commercial magnesium with a focus on the anisotropy and the possible microstructural causes of this behavior. The rolling process will be part of the second aspect. The aim is to show the influence of the parameters on the microstructure and texture and how this could affect the anisotropy in the rolled sheets. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Aerospace gas turbine disks operate in an environment of relatively high stresses caused by centrifugal forces and elevated temperatures. These severe conditions necessitate the need for materials with high temperature strength and good low cycle fatigue resistance. One class of alloys used for this task is the nickel base superalloys, out of which, IN 718 is the most widely used in the aerospace industry. The properties of IN 718 are attributed to the combined effects of the chemistry, heat treatment, and microstructure. The chemistry is tailored not only for solid solution strengthening but also for precipitation hardening developed during heat treatment, which combined with a fine grained microstructure lead to excellent mechanical properties such as low cycle fatigue resistance and elevated temperature strength. The properties of a gas turbine disk are sensitive to the microstructure, in particular the grain size, which ...

International Nuclear Information System (INIS)

The effect of mean stress, or the stress ratio (R), on the fatigue-crack growth (FCG) behavior of #alpha#-aged and #omega#-aged microstructures of the beta titanium alloy Ti-10V-2Fe-3Al was investigated. While the mean stress had a negligible effect on the FCG behavior of the #alpha#-aged microstructure, a strong effect was observed in the #omega#-aged microstructure. In particular, the values of the threshold stress-intensity range (#DELTA#K_t_h) exhibited a strong dependence on R in the #omega#-aged microstructure, while this dependence was weak in the #alpha#-aged microstructure. These effects seem to arise primarily from fracture-surface roughness-induced crack closure. The crack closure levels for the #alpha#-aged microstructure were found to be very low compared to those for the #omega#-aged microstructure. Transmission electron ...

Energy Technology Data Exchange (ETDEWEB)

In this study, deformation modes and precipitations have been characterized in test pieces made of alloy 800, grade 2 hyper-hardened state and age-conditioned for 3000 h at 550/sup 0/C, used for steam generator tubes of the Super Phenix Reactor, after continuous fatigue and fatigue-relaxation tests in the oligocyclic range. This microstructural study has provided an interpretation of the fatigue behaviour of the material.

Energy Technology Data Exchange (ETDEWEB)

Mechanical alloying is an important pre-requisite for the manufacturing of heat resistant oxide-dispersion-strengthened superalloys. Though the microstructure of these materials after hot extrusion and recrystallization treatment is well documented, little is known about the microstructural evolution during ball-milling. A method was tested to prepare electron transparent foils and extraction replica from powder particles for TEM investigations. The microstructure was found to consist of a Ni-Cr-Al solid solution in which submicron particles of refractory metals were embedded. The extremely fine grainize of about 50 nm is the consequence of severe plastic deformation. Yttria particles could not be detected in the powder after ball milling, but after a heat treatment at 1000 C the well-known fine dispersion of oxide particles was evident. (orig.)

International Nuclear Information System (INIS)

Radiation hardening in austenitic stainless steels is shown to modify deformation characteristics and correlate well with an increased susceptibility to intergranular stress corrosion cracking (IGSCC). Available data on neutron-irradiated materials have been analyzed and correlations developed between fluence, yield strength and cracking susceptibility in high-temperature water environments. Large heat-to-heat differences in the critical fluence (0.2 to 2.5 x10"2"1 n/cm"2) for IGSCC are documented. In many cases, this variability is consistent with yield strength differences among irradiated materials. IGSCC correlates better to yield strength than to fluence for most heats suggesting a possible role of radiation-induced hardening and microstructure on cracking. Microstructural evolution during proton and heavy-ion irradiation has been characterized in low-carbon 304SSs. Hardening results from a dispersion of dislocation ...

Energy Technology Data Exchange (ETDEWEB)

In this study, isothermal torsion tests were carried out on magnesium AZ31B alloy under constant strain rate conditions, in the range of 250 to 400 C at 0.01, 0.1, and 1.0 s{sup -1}. Alloy flow stress dependence on strain rate and temperature can be described by a power law with activation energy of 130 kJ/mol. Microstructural examination of hot deformed samples shows very fine recrystallized grains decorating grain boundaries of larger gains in the form of a necklace. These fine grains are produced by dynamic recrystallization at the grain boundaries of original grains. Microstructure evolution, based on samples quenched at different strain levels, indicates that increasing deformation strain has little effect on recrystallized grain size but widens the recrystallized region, with full recrystallization achieved at a certain high strain level. Recrystallized grain size increases with increasing ...

Energy Technology Data Exchange (ETDEWEB)

The microstructural development inside the stress induced martensite (SIM) variants in Ti-Ni-Nb alloy with various degrees of deformation have been revealed by electron microscopic observations. The orientation relationship between the SIM and the parent phase has been found: [1{bar 1}0]{sub M}{parallel}[11{bar 1}]{sub B2}, (001){sub M} 5{degree} away from (101){sub B2}. The lattice invariant shear of the SIM variants at the slightly deformed stage is dominantly (11{bar 1}) Type I twin. Besides the ordinary slip, the adjustment and development of the internal secondary twinning from (11{bar 1}) Type I twin to {l_angle}011{r_angle} Type II/ or (011) Type I twin, (001)compound twin and (111) Type I twin happen concurrently or in combination inside the SIM variants with the further deformation. The corresponding deformation mechanisms include stress induced reorientation of SIM ...

International Nuclear Information System (INIS)

The constituent phases and associated deformed microstructure of the quenched Ti-xNb-(0.5-1.5) at.% Si alloy consisting of non-cytotoxicity elements, where x = 24-30 at.%, were investigated to provide pseudoelasticity for biomedical and sensor applications. Optical microscopy revealed that stress-induced martensitic transformation takes place during the deformation in the present alloys. It is confirmed from the X-ray diffraction results of the deformed specimens that the crystal structure of the stress-induced martensite phase is the orthorhombic so-called #alpha#'' structure. Within the alloys having #beta#(bcc) phase studied Nb-poor region appeared to exhibit a dominant behavior for stress-induced martensitic transformation than Nb-rich region. This result suggests that metastable #beta# phase is superior to stable #beta# phase for the occurrence of stress-induced martensitic transformation in the ...

International Nuclear Information System (INIS)

Microstructure and properties of a Mg AZ31B laser beam weld without filler are studied using electron microscopy, X-ray diffraction and mechanical tests. The microstructure of the weld is characterized by a narrow heat affected zone, columnar grains and precipitate coarsening in the fusion zone. Texture in the fusion zone is significantly different from the texture of the base material. The residual stress distribution observed is similar at the top and the bottom of the weld, maximum tensile residual stress values are observed in the fusion zone. Tensile tests reveal differences in the mechanical behavior of the fusion zone and the parent material, which can be related to the differences of texture and the resulting deformation mechanisms.

International Nuclear Information System (INIS)

Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that SThM can be used as a tool for the thermal property and ...

Science.gov (United States)

Hot-torsion testing was used to establish the cavitation behavior of a typical alpha/beta titanium alloy, Ti-6Al-4V, with a colony microstructure, during simple-shear deformation. For this purpose, sections of deformed specimens were examined by optical metallography, and by scanning and orientation-imaging microscopy (OIM). It was found that cavity nucleation occurred along prior beta boundaries as well as at triple points; in particular, most cavities nucleated along boundaries perpendicular to the axial direction of the specimen. Extensive growth was observed for cavities surrounded by both hard and soft orientations, with the soft colonies accommodating more of the imposed strain. At high degrees of deformation, dynamic globularization of the colony microstructure adjacent to the cavities was also observed. In addition, the metallographic observations revealed that the cavities ...

International Nuclear Information System (INIS)

In this paper, an investigation was performed on a failure pressure vessel, which was as an anti-freezing heater for General Gas Storage and Distribution (SGZ) system. Evident and serious deformation was observed on the body of the vessel. A metallurgical investigation was conducted to establish the mechanism and cause of deformation of the anti-freezing heater at Daya Bay PWR station in China. The investigation, which was performed on specimens cut from the most serious area deformed of the vessel, included macroscopic examination and microscopy examination. The results of the examinations showed that some lamellar pearlite in the microstructure were already spheroidized. It was confirmed that the vessel was operated at high temperature. Stress analysis for the vessel was conducted. And it was confirmed that, in ideal conditions, the vessel would be deformed at around 420 C. The ...

Energy Technology Data Exchange (ETDEWEB)

Woven Kevlar fabrics exhibit a number of beneficial mechanical properties which include strength, flexibility, and relatively low density. The desire to engineer or design Kevlar fabrics for specific applications has stimulated interest in the development of theoretical models which relate their effective mechanical properties to specific aspects of the fabric morphology and microstructure. In this work the author provides a theoretical investigation of the large deformation elastic response of a plane woven Kevlar fabric and compares these theoretical results with experimental data obtained from uniaxially loaded Kevlar fabrics. The theoretical analysis assumes the woven fabric to be a regular network of orthogonal interlaced yarns and the individual yarns are modeled as extensible elastica, thus coupling stretching and bending effects at the outset. This comparison of experiment with theory indicates that the deformation ...

International Nuclear Information System (INIS)

A study was made into microstructure and texture of cold rolled titanium alloy VT-35 with various hydrogen content aimed to reveal hydrogen influence on the mechanism of cold plastic deformation by rolling. Experiments were carried out using sheets 1.2 mm thick hydrogenated up to hydrogen concentrations from 0.06 to 0.554 mass. %. All specimens constituted a single-phase FCC #beta#-solid solution. It is shown that small hydrogen additions have a plasticizing effect on #beta#-titanium alloys in their cold rolling. The character of texture is dependent on hydrogen concentration and determined by deformation mechanism. 6 refs.; 5 figs.

Energy Technology Data Exchange (ETDEWEB)

AZ31 Mg alloy samples were extruded by an equal channel angular extrusion (ECAE) process and subsequently annealed to obtain fine-grained material with a low dislocation density. Tensile tests at room temperature exhibited an apparent steady-state deformation region and a large tensile elongation of 47%. The deformed microstructure at an elongation of 2% indicated a substantial cross-slip to nonbasal planes possibly induced by grain-boundary compatibility effects. The nonbasal segments of dislocations were found to consist of 40% of the total dislocation density at a yield anisotropy factor of only 1.1 instead of an expected value of 100 from single-crystal experiments. (orig.)

Energy Technology Data Exchange (ETDEWEB)

An axisymmetric unit cell model based on a regular array of second-phase particles arranged on a BCC lattice is used to study deformation mechanisms of ferrite-pearlite structural steels. Microstructural characteristics of the steels were parameterized by the pearlite volume fraction, the aspect ratio of the pearlite particles, and the neighboring factor, which represents the ratio of interparticle spacing in the longitudinal direction to that in the transverse direction. FE analyses were carried out to investigate the macroscopic and microscopic response of unit cells with morphological features based on idealizations of the microstructures of the actual steels. Tensile properties of each constituent phase were obtained experimentally and used in the analyses. As compared to traditional axisymmetric models, the BCC tell model appears to be able to capture more realistically the behavior of the materials, and it accurately ...

Energy Technology Data Exchange (ETDEWEB)

The grain boundary crystallographic misorientations of magnetic-pulse-welded (MPW) aluminum alloy (AA) 6061-T6 in linear and tubular configurations were examined using the electron backscattered diffraction (EBSD) technique. A refined structure of heavily deformed grains with higher grain boundary angles was observed in linear welds. Significant spalling was observed away from the joints, in the interior of tubular welds. The results show the complex interaction of shock waves with the materials during this impact welding process.

Energy Technology Data Exchange (ETDEWEB)

During rolling contact fatigue of the inner rings of ball bearings three stages of material response can be distinguished, in terms of the volume that is plastically deformed upon overrolling. After a first stage of material strengthening during which a decrease occurs for the volume that is deformed plastically, an effectively stationary, second stage is entered which is eventually succeeded by a third stage exhibiting a pronounced increase of the volume that is deformed plastically upon overrolling, which leads to failure. It is suggested that carbon diffusion induced by local temperature peaks occurring at the moment of overrolling is the key mechanism leading to fatigue damage. The amount of decomposed retained austenite is a useful, practical parameter to assess fatigue life. It is shown that published ideas about the role of certain components of residual stress in enhancing fatigue life are not correct and that the ...

Energy Technology Data Exchange (ETDEWEB)

Determination of stacking fault energy (SFE) of the austenite phase of a duplex stainless steel DIN W.-Nr.: 1.4462 has been carried out using transmission electron microscopy. Furthermore, cold rolling tests and microstructural analysis have been realized in order to allow a detailed discussion of the obtained SFE-values. The results of this investigation indicate that the stacking fault energy of the austenite phase within the duplex stainless steel is lower than of one-phase austenitic stainless steels. This is justified by the chemical composition, mainly by the Cr and Ni alloying contents. Nevertheless, work hardening of the austenite during cold deformation is not as accentuated as expected by the SFE-values, because at higher deformation levels the deformation mainly occurs within the ferrite phase 7 refs., 5 figs., 2 tabs.

International Nuclear Information System (INIS)

Bulk nanocrystalline pure iron rods were fabricated by the equal channel angular pressure (ECAP) technique up to eight passes. The microstructure and grain size distribution, natural immersion and electrochemical corrosion in simulated body fluid, cellular responses and hemocompatibility were investigated in this study. The results indicate that nanocrystalline pure iron after severe plastic deformation (SPD) would sustain durable span duration and exhibit much stronger corrosion resistance than that of the microcrystalline pure iron. The interaction of different cell lines reveals that the nanocrystalline pure iron stimulates better proliferation of fibroblast cells and preferable promotion of endothelialization, while inhibits effectively the viability of vascular smooth muscle cells (VSMCs). The burst of red cells and adhesion of the platelets were also substantially suppressed on contact with the nanocrystalline pure iron in blood ...

British Library Electronic Table of Contents (United Kingdom)

A fully lamellar ferrite/cementite nanostructure was designed in a low C steel by using a specific thermal treatment. The strengthening of such microstructure has been investigated as a function of prestrain by rolling up to a deformation of 300%. As in usual pearlitic structure, its work-hardening shows no saturation and its elongation to fracture remains rather constant instead of decreasing drastically as conventional steels. The hardening by a similitude effect is thus not the privilege of pearlitic steels. Nevertheless, its lower initial work-hardening rate at low strain compared to an equivalent pearlitic steel and a lower hardening potential at high strain let us suspect major differences in the nature and the behaviour of ferrite channels in relation to the morphogenesis of the mic...

International Nuclear Information System (INIS)

The present work focuses on the transformation of high-purity Ni powder blends of controlled volume fractions (40 and 60 %) of nanometre-sized (100 nm) and micrometre-sized (544 nm) particles into bulk samples as part of a strategy for producing ultrafine-grained materials usefully exhibiting both strength and ductility. The process involved cold isostatic pressing at 1.5 GPa and sintering. The resulting bulk samples had relative densities near 95 %, were texture-free, and exhibited two different grain size distributions with an average value of 600 #+-# 30 nm. The mechanical properties were investigated by compression and microhardness tests, both at room temperature, and compared to the behaviour of a sample processed from micrometre-sized powder only. Samples prepared from the blends exhibited high yield stresses of 440 and 550 MPa after compression, and they did sustain work hardening. Tests conducted before and after compression up to 50 % deformation showed ...

Energy Technology Data Exchange (ETDEWEB)

In view of the situation that aging of boiler components proceeds and some `Type IV` cracking incidents are reported recently, the development of an accurate remaining life evaluation method for boiler weldment parts is an important subject for the utilities. In this study, simulated materials with coarse and fine grain microstructures in a weldment heat affected zone were produced, and their high temperature strength properties were evaluated. The strength property of the weld joint was also discussed based on the experimental and analytical results. It was found that the creep rupture strength of the fine grain material was as low as 1/2 of the base metal and as 1/5 of the coarse grain material, and the weld joint ruptured at the fine grain region in a shorter period than the base metal as the applied stress level decreased. Many grainboundary creep cavities were also observed in the fine grain region. A creep deformation analysis by FEM ...

Science.gov (United States)

... Accession Number : ADD100229. Title : DEFORMATION BEHAVIOR OF AN OMEGA HARDENED ALPHA-BETA TITANIUM ALLOY,. ...

Energy Technology Data Exchange (ETDEWEB)

Alloyed steels containing retained austenite after martensitic hardening are widely applied in technical practice. Although many practical investigations have been made into the mechanical behaviour of composite microstructures with retained austenite, there is still a lack of knowledge concerning their fatigue and crack propagation behaviour. For this reason, the author investigated the effects of retained austenite concentration and stability on the transformation and deformation behaviour of hardened states of the steels X210Cr12 and 100Cr6. For this purpose, monotone tensile tests, cyclic tensile pressure tests, and supplementary crack propagation experiments were carried out. The concentrations of retained austenite were varied between 10 and 100% by volume by means of different heat treatments. [Deutsch] Legierte Staehle, die nach martensitischer Haertung noch Restaustenit enthalten, finden in der technischen Praxis verbreitete Anwendung. ...

Energy Technology Data Exchange (ETDEWEB)

We calculate mass spectrum of CHS model deformed by an exactly marginal operator, and find that there are tachyons which are not localized in the target space. Similar deformation is discussed in another CFT which corresponds to separated NS5-branes. A condensation of the tachyons is briefly argued.

UK PubMed Central (United Kingdom)

BackgroundMany molecules of interest are flexible and undergo significant shape deformation as part of their function, but most existing methods of molecular shape comparison (MSC)...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

In this study, a range of joining technologies has been investigated for creating attachments between refractory metal and Ni-based superalloys. Refractory materials of interest include Mo-47%Re, T-111, and Ta-10%W. The Ni-based superalloys include Hastelloy X and MarM 247. During joining with conventional processes, these materials have potential for a range of solidification and intermetallic formation-related defects. For this study, three non-conventional joining technologies were evaluated. These included inertia welding, electro-spark deposition (ESD) welding, and magnetic pulse welding (MPW). The developed inertia welding practice closely paralleled that typically used for the refractory metals alloys. Metallographic investigations showed that forging during inertia welding occurred predominantly on the refractory metal side. It was also noted that at least some degree of forging on the Ni-based superalloy side of the joint was necessary to achieve consistent bonding. Both ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Investigated are the characteristics of high-temperature plastic deformation the velocity sensitivity of flow stresses, deformation curves, flow stresses, deformation before rupture - as well as the structure of beryllium alloys containing nickel (0.5-4 %), yttrium (0.5-2 %) and aluminium (38 %). The alloys containing nickel (2%) and yttrium (0.5 %) are superplastic, however, deformation before fracture of the alloys is lower than that of the unalloyed beryllium. The singularities of high-temperature plastic flow of the alloys and the causes of deterioration of their plasticity are determined.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... crystals and polycrystals. Nevertheless, explosive forming, magnetic forming, etc., are all high-strain-rate processes that ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

Science.gov (United States)

... THE STRENGTH, TOUGHNESS, AND STRESS-CORROSION CRACKING SUSCEPTIBILITY OF A METASTABLE BETA TITANIUM ALLOY (Ti-11. ...

International Nuclear Information System (INIS)

The methods of optical and transmission electron microscopy were used to study the influence of different programmes of hot deformation on the structure formation of (#alpha#+#beta#) titanium alloy VT9. The #beta# alloy VT-15 was studied at the same time in order to simulate the dislocation structure generated in the process of hot deformation. During the hot deformation of two-phase titanium alloys in both #beta# and (#alpha#+#beta#) ranges there is found to be an optimum range of deformation in which a homogeneous, polygonized structure is formed.

International Nuclear Information System (INIS)

There is no possibility to check any inner part at real welded joint at nuclear power station (NPS) during operation because any destructive test cannot be used. In practice there is checked surface of weld. There are used four methodical instructions for the check of real welds: 1. The visual inspection, 2. The measurement of hardness, 3. The chemical composition checking and 4. The microstructure replica analysis. It is necessary to know how these information of weld surface are in accordance with characteristics of inner parts of weld. If there is not any difference between surface weld microstructure and internal weld microstructure of experimental weld it is supposed to that there is not any difference in other measured properties of welds. If is changed structural characteristics of microstructure, it is changed also hardness, chemical analysis etc. It was observed that the ...

Energy Technology Data Exchange (ETDEWEB)

Based on techniques of organic solvent extraction and a thermal model experiments of coal-related hydrocarbon, the variation of coal structure and the character of deformed coal-related hydrocarbons were studied when the coal seam at Piagdingshan mine, China was modified by tectonic stress. The results show that the extraction ratio by n-hexane and benzene from the deformed coal approaches that form normal coal, but the extraction ratio by chloroform from the deformed coal is two times more than that from normal coal. The deformed coal has higher solvable low-molecular weight compounds than normal coal. The intermolecular force of deformed coal is relatively small. The deformed coal has low strength and high adsorption capacity, and these determine the outbreak of coal-gas outburst. The extraction yields by chloroform can be taken as an index of forecast risks ...

Energy Technology Data Exchange (ETDEWEB)

The Gordon Research Conference (GRC) on ROCK DEFORMATION was held at II Ciocco from 5/19/02 thru 5/24/02. Emphasis was placed on current unpublished research and discussion of the future target areas in this field.

International Nuclear Information System (INIS)

... deformed nuclei eigenvalues even-odd nuclei gold 195 hamiltonians iridium

Science.gov (United States)

Analytical models for predicting the deformation and failure of composite sandwich panels subjected to blast and projectile impact loading are presented in this paper. The analytical predictions of the transient deformations and damage initiation in the composite sandwich panels were compared with finite element solutions using ABAQUS Explicit. For the blast model, the predicted transient deformation of the sandwich panel was within 7%of FEA results, while the predicted damage initiation using Hashin's composite failure criteria was about 15%higher than FEA results in most cases. For the high velocity impact model, the predicted transient deformations were within 20%of FEA results.

International Nuclear Information System (INIS)

... coupling deformed nuclei gold 195 high spin states iridium 187 moment of

International Nuclear Information System (INIS)

Full text of publication follows: Radiation hardening and embrittlement due to high-energy neutron radiation around 623 K are the important issues on reduced-activation ferritic/martensitic (RAF/M) steels. It is expected that the improvement of radiation hardening might be one of effective ways to control the mechanical properties of RAF/M after irradiation. It has been reported that the weld joint has less hardening than the base metal from the tensile test results of TIG weldments irradiated in HFIR. This report indicated that radiation hardening can be reduced by the optimization of heat treatment condition for F82H. The purposes of this study are to establish the condition of heat treatment for minimum of radiation hardening in F82H steel using Neutron/Ion-irradiation and to examine a correlation between tensile property and micro-hardness before/after irradiation. The materials used in this study were F82H IEA heat and F82H heat treatment variants. Neutron irradiation was ...

Energy Technology Data Exchange (ETDEWEB)

We study certain supersymmetry breaking deformations of linear dilaton backgrounds in different dimensions. In some cases, the deformed theory has bulk closed strings tachyons. In other cases there are no bulk tachyons, but there are localized tachyons. The real time condensation of these localized tachyons is described by an exactly solvable worldsheet CFT. We also find some stable, non-supersymmetric backgrounds.

International Nuclear Information System (INIS)

The applicability of conventional strength hypotheses in the long-term creep range was examined by means of multiaxial loaded small and large-scale specimens of 1% CrMoNiV-steel at 550deg C. The experimentally determined deformation behaviour in the primary and secondary creep range was simulated by means of a finite element analysis. The creep deformation capacity is influenced by the degree of multiaxiality. The validity of a strength hypothesis depends on the type of load and on deformation resp. failure criteria. (orig.).

Energy Technology Data Exchange (ETDEWEB)

To investigate the influence of equal channel angular pressing on the microstructure and texture of the magnesium alloy AZ31, electron backscattering diffraction and well as neutron diffraction experiments were carried out. Through these experiments it was possible to trace the microstructure and texture evolution with strain accumulated with the increasing number of equal channel angular pressing passes. It was further demonstrated by subsequent compression tests that the microstructural changes produced by equal channel angular pressing have a beneficial effect on both the compressive strength and ductility of AZ31. (orig.)

Science.gov (United States)

Not Available

Energy Technology Data Exchange (ETDEWEB)

By characterising the microstructure, quantitative image analysis allows to draw conclusions on the mechanical properties of materials. On fine microstructures with low contrast, e.g. of hardened steels, texture analysis has to be applied for quantification. Feeding texture parameters according to Haralick into a trained neural network, a correlation between the microstructure and the hardness of the steels C45 and 100Cr6 can be achieved. (orig.)

International Nuclear Information System (INIS)

Both microstructural graded and homogenous single-phase #alpha#-Sialon is obtained from Si_3N_4 powder for a broad range of compositions of practical interest. Elongated grains of #alpha#-Sialon could be developed in the monophase material by controlled mechanism of nucleation and growth. Tailoring of microstructure was realized through slow transformation reaction from Si_3N_4 to #alpha#-Sialon at lower temperature than sintering temperature when the composition is near the #alpha#-Sialon phase boundary. The mechanical properties are strongly correlated with the microstructure and are enhanced greatly in the optimized Sialon composition. (author)

Energy Technology Data Exchange (ETDEWEB)

In this paper, aluminium nitride synthesis is carried out by direct laser irradiation onto an aluminium target surface in a nitrogen containing atmosphere. The influence of various processing parameters on the microstructure of AlN thin films is investigated in order to improve their tribological properties. The main microstructural characteristics: nature, concentration, in depth distribution and morphology of various phases are studied versus processing parameters by TEM and GIXD. (author). 2 refs., 1 fig., 2 photos.

British Library Electronic Table of Contents (United Kingdom)

Ground deformation affecting the Umbria region (central Italy) in the 9-year period from 1992 to 2000 was investigated through multi-temporal Differential Synthetic Aperture Radar Interferometry (DInSAR). For the purpose, the Small BAseline Subset (SBAS) technique was adopted, which allows studying the temporal evolution of the detected deformation at two spatial scales: a low-resolution (regional) scale, and a full-resolution (local) scale. For the analysis, SAR data acquired by the European Remote Sensing (ERS-1/2) satellites along ascending and descending orbits were used. The detected deformation was analysed to investigate its relevance to geophysical, geomorphologic, and human-induced processes that may result in hazardous conditions to the population of Umbria. Low-resolution deform...

International Nuclear Information System (INIS)

Water repellency en the microstructure super-hydrophobic cured surface is important for research and industrial purposes. This microstructure film can be cured on polyethylene terephthalate PET surface by electron beam (EB) at different irradiation doses 10-100 kGy. The microstructure formulation composed from hydrophobic acrylate oligomer (EB 244) and monomer (SR 440). The irradiation induced cross linking of the prepared microstructure was proved by FTIR spectroscopy and the adhesion force by abrasion test. Some factors affecting the adhesion force of the prepared microstructure film such as oligomer/monomer composition ratio and the thickness of the microstructure cured film were studied. The contact angles (8) were measured on cured surfaces before and after adding the super hydrophobic nanoparticles (Zonyl 9361). The super-hydrophobic cured surface showed ...

International Nuclear Information System (INIS)

The purpose of this research is to investigate the micro-mechanism of deformation behavior of metallic glasses. We report the results of direct observations of short-range and medium-range structural change during tensile deformation of metallic glasses by high energy X-ray diffraction method. Cu50Zr50 and Ni30Zr70 metallic glass samples in the ribbon shape (1.5 mm width and 25 ?m) were made by using rapid quenching method. Tensile deformation added to the sample was made by using special equipment adopted for measuring the high energy X-ray diffraction. The peaks in pair distribution function g(r) for Cu50Zr50 and N30iZr70 metallic glasses move zigzag into front and into rear during tensile deformation. These results of direct observation on atomic distribution change for Cu50Zr50 and Ni30Zr70 metallic glass ribbons during tensile deformation suggest that the micro-relaxations ...

Energy Technology Data Exchange (ETDEWEB)

Lifetimes have been measured in the {pi}h{sub 9/2} (yrast) and {pi}i{sub 13/2} (excited) bands in the nuclei {sup 181}Ir and {sup 187}Au using the Recoil Distance Method (RDM). The results clearly indicate that the {pi}i{sub 13/2} band exhibits an increased deformation over the {pi}h{sub 9/2} band, in keeping with the premise that the delayed crossing in this band is due to enhanced quadrupole deformation. (author). 3 refs, 1 fig, 2 tab.

Energy Technology Data Exchange (ETDEWEB)

The paper reports extensive analyses of the fractal geometry of cellular dislocation structures observed in Cu deformed in multiple-slip orientation. Several methods presented for the determination of fractal dimensions are shown to give consistent results. Criteria are formulated which allow the distinguishing of fractal from non-fractal patterns, and implications of fractal dislocation patterning for quantitative metallography are discussed in detail. For an interpretation of the findings a theoretical model is outlined according to which dislocation cell formation is associated to a noise-induced structural transition far from equilibrium. This allows relating the observed fractal dimensions to the stochastic properties of deformation by collective dislocation glide.

Energy Technology Data Exchange (ETDEWEB)

In order to design the microstructure of ceramics with desired dielectric property, an estimation method of dielectric constant of ceramics taking into account the characteristics of microstructure of the ceramics is proposed. In the estimation model, the microstructure of ceramics is represented by the assembly of unit cells comprising of grain, pore and grain boundary. The sizes of grain and pore and the thickness of grain boundary in each unit cell were determined exactly according to their size and thickness distributions in a real ceramic. The dielectric constant of the assembly can be calculated on the basis of equivalent circuit theory. The estimated values of dielectric constant of ceramic BaTiO{sub 3} using the proposed estimation method agree well with experimental ones. The dependence of characteristics of microstructure on the dielectric constant was clarified by the estimation of dielectric ...

International Nuclear Information System (INIS)

(7 Jan 1974). Netherlands Rebel, H. Hauser, G. Schweimer, GW Nowicki,

Science.gov (United States)

... The effects of these voids were more noticeable for tantalum and aluminum electrolytic capacitors, which usually exhibited severe case deformation ...

Energy Technology Data Exchange (ETDEWEB)

Morphological and structural changes of nylon 66 were evaluated during a continuous heat-draw process. Results are discussed.

Science.gov (United States)

In this work we examine a five-dimensional brane-world model with brane structure driven by a real scalar field. From the deformation of a kink-like defect we find a new class of brane solutions containing internal structures which have implications for the way the background space-time is constructed and the way its curvature behaves. Initially, for spin 0 scalar field, we find a zero mode which can be localized on the deformed brane. However, this result can change by the gravitational interaction with the brane internal structure. Analyzing the massive modes of the scalar field, using two different methods, we find resonance structures similar to those found in the study of gravity localization. The main objective here is to observe the contributions of the deformation procedure to the resonances and to the well known field localization methods.

International Nuclear Information System (INIS)

The positive-energy unitary irreducible representations of the q-deformed conformal algebra #delta#C_q = U_q(su(2,2)) are obtained by appropriate deformation of the classical ones. When the deformation parameter q is N -th root of unity, all these unitary representations become finite-dimensional. For his case we discuss in some detail the massless representations, which are also irreducible representations of the q-deformed Poincare subalgebra of #delta#C_q. Generically, their dimensions are smaller than the corresponding finite-dimensional non-unitary representation of su(2,2), except when N = 2 modul h + 1, where h is the helicity of the representations. The latter cases include the fundamental representations with h = #+-#1/2. (author). 10 refs.

International Nuclear Information System (INIS)

(1974). Romania Gils, HJ Rebel, H. Kernforschungszentrum Karlsruhe

International Nuclear Information System (INIS)

... SCIENCE SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS

Energy Technology Data Exchange (ETDEWEB)

Doubly decoupled structures in doubly odd deformed nuclei are reexamined and shown to be composed of a pseudo-spin aligned neutron and a decoupled proton. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Investigations of dislocation structure and mechanical properties of iron after rolling deformation in shaped rolls and after hydroextrusion are conducted. It is shown that dislocation iron structure slightly changes with deformation degree after rolling in shaped rolls and annealing and it is characterized by low density of screw dislocations. Cold brittleness temperature decreases in the result of rolling and the succeeding recrystallization and impact strength increases both at room temperature and at low temperatures. Screw dislocations having high Peierls barrier prevail in the structure after hydroextrusions. The iron deformed by hydroextrusion at 400 mPa and higher after annealing has high cold brittleness temperature and low impact strength.

UK PubMed Central (United Kingdom)

For a set S of points in ℝ^d, an s-spanner is a subgraph of the complete graph with node set S such that...Full Text Available

Science.gov (United States)

... F ? (28.3)(108) in an isotherme.l deformation with stationary principal axes of strain rate, but the component might be as small as F2= (19-3)(100) ...

Science.gov (United States)

Pore Fraction in Yttrium-Barium-Copper-Oxide and. Other Polycrystalline. Materials ...... Properties of Yttrium Ceramic. Sov. J. LowTemp.Phys. 14:395-402 . ...

International Nuclear Information System (INIS)

1972. United States Narayanan, GH Archbold, TF Univ. of California Press.;

Energy Technology Data Exchange (ETDEWEB)

In this letter, examples of microstructural instabilities that can significantly affect the low crystal fatigue (LCF) life are pointed out.

KoreaScience (Korea)

Full Text Available

British Library Electronic Table of Contents (United Kingdom)

A microanalytical characterization of cast magnesium alloys of eutectic origin based on the Mg?Al?Ca ternary matrix system has been carried out in order to investigate the influence of alloying elements on their microstructure as well as microchemistry-processing-microstructural relations using structure-sensitive techniques of electron microscopy, mechanical spectroscopy (internal friction), X-ray diffractometry, and advanced microanalytical methods including electron probe compositional analysis. Following the data obtained here there is direct correlation of microstructure with creep properties of the new experimental magnesium alloys. The creep and heat-induced properties of the multicomponent magnesium alloys containing low range of inexpensive additions of titanium (0.07?0.2%) or str...

Energy Technology Data Exchange (ETDEWEB)

The strain gradient crystal plasticity theory is applied to study the deformation of planar single crystal with a void under a nominally uniaxial tension. The crystal theory assumes elevated strain hardening due to slip gradients and has a constitutive length scale. The effects of the void size with respect to the constitutive length scale on the single crystal deformation are investigated.

Energy Technology Data Exchange (ETDEWEB)

Reports by U.S. workers on geodetic measurements of recent plate motions or crustal deformation published in 1987-1990 are reviewed. The review begins with global plate motions, proceeds through plate boundaries in California, Alaska, and the Pacific Northwest, and finishes with volcanic phenomena, monument stability and longevity, and GPS relative position measurements. 184 refs.

Energy Technology Data Exchange (ETDEWEB)

The paper discusses the problem of influence of grain boundaries structure on mechanical properties of aluminium alloys at elevated temperatures. Showed the data amount of grain boundaries close to special and a random of grain boundaries. The results of calculation of contribution of different mechanisms of deformation to the total deformation for alloys with different types of grain boundaries are given. (orig.)

UK PubMed Central (United Kingdom)

Dynamic deformation and recovery responses of red blood cells (RBCs) to a cyclically reversing shear flow generated in a 30-μm clearance, with the peak shear stress of 53, 108,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

In the development of the man-made island siting technology of nuclear power plants, assessing the stability of the seawall against large ocean waves and earthquakes is indispensable. Concerning with the seismic stability of the seawall, prediction of the deformation like sliding and settlement of the seawall during earthquake including the armour units in front of the caisson becomes important factor. For this purpose, the authors have developed the two-dimensional DEM-FEM coupled analysis method (SEAWALL-2D) to predict the deformation of the seawall covered with the armour units during earthquake. In this method, movements of the armour units are calculated in DEM analysis part and deformation of the caisson, rubble moundsand seabed and back fill are calculated in FEM analysis part taking the nonlinearity of the soil materials based on the effective stress into account. Numerical simulations of dynamic centrifuge model ...

Science.gov (United States)

The effect of solution treatment temperature and oxygen content on the microstructure and age hardening response of the metastable beta alloy Ti-11.5Mo-6Zr-4.5Sn have been studied. Kinetics of formation of the equilibrium alpha-phase and the metastable om...

International Nuclear Information System (INIS)

The creep behaviour of different casts of Alloy 800, supplied by different sources, has been determined in multispecimen furnaces at 650, 750 and 800"0C and at different stress levels up to about 14,000 hs; the environment was initially helium and then air. The microstructural investigations were carried out by transmission electron microscopy. (Auth.).

Energy Technology Data Exchange (ETDEWEB)

Recent development in application of a focused ion beam (FIB) technique to preparation of thin foil specimens for transmission electron microscopy (TEM) observation has been reviewed. Combined technique of FIB/TEM enables one to analyze those microstructures which have been almost impossible or very difficult to analyze so far. (author)

Energy Technology Data Exchange (ETDEWEB)

The microstructural development and grain-coarsening behavior of WC-Co alloys, with and without a VC additive, were investigated. The primary goal was to determine the mechanism through which VC acts as a grain-growth inhibitor. The study involved long-time sintering experiments (1 to 100 hours) on fully dense material, nascent stage sintering (90 to 1,320 seconds) starting with the green compact, and surrogate liquid phase experiments to characterize the WC powder prior to sintering. Quantitative microstructural analysis using intercept length distributions was performed for the long-term sintering. The nascent stage experiments involved the measurement of the specific surface area (S{sub v}) of each type of interface separately allowing the determination of the contribution of each developing entity to the overall microstructural evolution. The VC addition has been found to enhance the breakup of multigrained particles in ...

International Nuclear Information System (INIS)

Buried silicon carbide (SiC) microstructures with lateral dimensions in the #mu#m range were formed by high-dose projection of 1.5 MeV C"2"+ ions in Si(100) at different doses and temperatures and subsequent annealing for 10 h at 1250 deg. C. Sections of individual SiC microstructures were prepared for cross-sectional transmission electron microscopy (TEM) analysis using a focused ion beam (FIB). Besides the possibility to select an individual microstructure, the FIB technique has the advantage of producing specimen foils of uniform thickness. Therefore, it was possible to map the carbon concentration of microstructures by energy filtered TEM (EFTEM) using the C_K absorption edge without the need of any sample thickness correction. Local overstoichiometric (>50%) carbon concentrations are shown to be correlated to the formation of an amorphous phase in the SiC and to significant swelling visible at ...

Energy Technology Data Exchange (ETDEWEB)

The theory of ..cap alpha.. decay in first-order perturbation theory is presented. The theory is designed for a strongly deformed nucleus in an isomeric state which changes its deformation dynamically through decay from a very deformed to an almost spherical shape. It is shown that other channels are not coupled to the ..cap alpha.. channel in first-order perturbation theory. The collective degrees of freedom of the daughter nucleus are described by shape vibrational states, eigenstates of a Hamiltonian whose potential has two minima. The parent nucleus is described by dynamically coupling the vibrational degrees of freedom to the ..cap alpha..-particle motion and also taking rotations into account. The ..cap alpha.. particle is taken to be a point-like particle. The theory is applied to the ..cap alpha.. decay of the isomeric state of /sub 95//sup 242/Am.

British Library Electronic Table of Contents (United Kingdom)

We demonstrate a novel cross-sectional deformation, called the radial corrugation, of multi-walled carbon nanotubes (MWNTs) under hydrostatic pressure. Theoretical analyses based on the continuum elastic approximation have revealed that MWNTs consisting of more than ten concentric walls undergo elastic deformations at critical pressure Formula Not Shown , above which the circular shape of the cross-section becomes radially corrugated. Various corrugation modes have been observed by tuning the innermost tube diameter and the number of constituent walls, which is a direct consequence of the core-shell structure of MWNTs. Cross-sectional views of MWNT under high hydrostatic pressure: elliptic deformation with the mode index n = 2 (left), and radial corrugations with n = 5 (center), and n = 6 ...

International Nuclear Information System (INIS)

A study is made into textures of deformation and primary recrystallization forming in a #beta#-titanium alloy doped with hydrogen in amounts from 0.04 to 0.55 mass. %, on cold rolling with a 70%-reduction and dehydrogenating annealing at 860 deg C. It is shown that a volume fraction of recrystallization texture components is determined by the nature of corresponding deformation texture, in its turn, depending on hydrogen concentration in the alloy. At low hydrogen contents the main texture components are #left brace#111#right brace# and #left brace#001#right brace#. A hydrogen content increase up to 0.09 - 0.18 mass. % results in formation of dominant components of #left brace#111#right brace# and #left brace#112#right brace#

British Library Electronic Table of Contents (United Kingdom)

In this paper we demonstrate the capabilities of our ArcGIS-based software development that includes an adapted database system and a GIS tool for storage, combined analysis and visualization of leveling data and interferometric synthetic aperture radar (SAR) deformation measurements. Preprocessed remote sensing image data are stored with metadata that include all processing routines and parameters. This allows reproduction and traceability of all processing steps. Deformation monitoring is supported through data searching and selection based on a variety of criteria. A methods toolbox allows spatio-temporal analyses for points, lines and areas (e.g. subsidence basins) in a graphical manner.

International Nuclear Information System (INIS)

Activation energy values for high temperature deformation of a beta -titanium alloy Ti-10V were determined from the flow stress strain rate data taken from the second increasing strain rate cycles, in order to find the rate controlling mechanism. Although the data obtained from first increasing strain rate cycles are considered most appropriated by the author in a previous study due to obvious reasons, the values obtained in present work are again indicative of lattice self diffusion in beta -phase as the rate controlling mechanism for this alloy and nevertheless suggest that two different activation energy values for a deformation process could be possible in a given temperature range, depending upon the data. (author)

International Nuclear Information System (INIS)

Early failure of an induction-hardening carbon steel pipe, which was used to transport tailing slurry, was caused by pitting corrosion. The microstructure on the internal pipe surface layer was found being a mixture of martensite, pearlite and ferrite. In this work, the pitting corrosion behavior of each constitute in the microstructure of steel is investigated with electrochemical noise analyses; the electronic properties of passive films were studied with Mott-Schottky relationship. It is found that the passive films formed on the materials under investigation are highly disordered n-type semiconductors. The high-to-low pitting susceptibility is ferrite > martensite > pearlite. The pitting resistance is related to the semiconductive nature of the passive film formed on each constitute. The pitting susceptibility increases with the donor concentration in the passive films. (author)

International Nuclear Information System (INIS)

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 ?m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

Energy Technology Data Exchange (ETDEWEB)

AISI 316L stainless steel was welded by the electron beam (EB) and laser techniques. Microstructural characteristics, hardness profile, creep rupture properties and creep damage of the welds were investigated. Fully austenitic microstructure was obtained in the two welds. The solidification structure of the welds consisted of the cellular and equiaxed dendrites. The creep rupture lives of the two welds were almost the same, and they were reduced by a factor of about two compared to the base metal. Moreover, the rupture elongation of the welds was lower than that of the base metal. Creep damage was observed in the ``parting`` region of the welds and in the heat-affected zone (HAZ), respectively. Final creep fracture occurred in the ``parting`` region of the welds. (orig.).

International Nuclear Information System (INIS)

The microstructure of commercial rolled magnesium alloy AZ31B (nominal composition Mg-3Al-0.9Zn-0.15Mn in wt.%) was investigated with the help of light microscopy, electron backscatter diffraction (EBSD) and X-ray diffraction technique after annealing in the temperature range from room temperature (RT) to 400 deg. C. Tensile tests at RT were performed to show the influence of the microstructure on mechanical properties. Static recrystallization (SRX) was observed during annealing of as-received alloy at and above 150 deg. C. Twins play an important role during SRX and serve as nucleation sites and preferred paths for growth of grains. The strong basal texture caused by rolling was weakened by SRX. Significant differences in the stress strain curves were observed for as-received and annealed specimens.

British Library Electronic Table of Contents (United Kingdom)

In the present paper, the effects of hydroxyapatite (HA) content on the microstructure, thermal and mechanical properties of Ti-based glassy alloy/HA composite prepared by spark plasma sintering (SPS) are investigated. The microstructure of the composites is homogeneous when the HA is lower than 2 wt%. When the HA content is higher than 3 wt%, the crystalline precipitates with size of less than 5 nm are distributed in the glassy matrix. HA decomposes during sintering procedure for the composite with high HA content. With increasing HA addition, compressive strength decreases. Especially for the HA content is over 2 wt%, the strength decreases sharply because of partial crystallization of glassy alloy matrix.

Energy Technology Data Exchange (ETDEWEB)

The temperature dependence of the dislocation mobility threshold is investigated on the basis of a dislocation model suggested by Frenkel-Kontorova. The critical value is obtained for the stress/temperature, corresponding to the dislocation depinning from its equilibrium position. The universal behaviour of a barrier height at finite stress and temperature is revealed and investigated.

UK PubMed Central (United Kingdom)

This paper presents a new deformable model using both population and patient-specific statistics to segment the prostate from CT images. There are two novelties in the proposed method. First,...Full Text Available

International Nuclear Information System (INIS)

A survey is given of the influence of surface deformations on heavy ion reactions. Emphasis is put on the effect of zeropoint fluctuations in the entrance channel and on the effect on grazing collisions in terms of an imaginary part of the scattering potential. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Superplasticity of polycrystalline metallic materials is a phenomenon which shows hundreds to thousands of percents of large plastic deformation without necking in a steady state of low stress, when the uni-axial tensile loading is done in some special thermo-mechanical conditions (some limited ranges of properly high temperature and low strain rate). The main mechanism of superplastic phenomenon is the grain boundary sliding, while the main mechanism of usual plastic deformation is the trans-granular sliding. In this research, the possibility of superplastic deformation in a magnesium alloy (AZ31Mg alloy) was experimentally investigated, because generally speaking, the magnesium alloy whose atomic structure is hexagonal does not have enough formability in a form of trans-granular sliding mechanism. In this paper, the detail of experimental results are shown and discussed. Moreover, the constitutive equations of Mg alloy ...

UK PubMed Central (United Kingdom)

Four-dimensional (4D) radiotherapy is the explicit inclusion of the temporal changes in anatomy during the imaging, planning, and delivery of radiotherapy. One key component of 4D radiotherapy planning...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Deformation mechanisms were investigated in fine-grain (d=7 {mu}m) AZ31 Mg alloy in order to understand their excellent room-temperature ductility. Dislocation cross slip from basal to non-basal planes was found to occur easily at room temperature at a plastic anisotropy factor of only 1.5 instead of several tens to 100 expected from the single crystal CRSS data. Enhanced grain-boundary sliding (GBS) was also found to occur at room temperature. The contribution of GBS strain was found to be approximately 8% of total strain. The enhanced activity of non-basal dislocation slip and GBS was attributed to grain-boundary compatibility effects. Moreover, dynamic recovery was found to occur during deformation at room temperature associated with the formation of recovery twins and small-angle grain boundaries. The occurrence of these deformation mechanisms at room temperature was considered to be a major reason for an excellent ...

Energy Technology Data Exchange (ETDEWEB)

In this paper we report a case with primarily unspecific arthralgia after surgical therapy of hallux valgus deformity and consecutive reflex sympathetic dystrophy in which MR led to the diagnosis of Lyme disease. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This work concerns the study of the nuclear superdeformation phenomenon in the rare earth region (A {approx} 150). The superdeformed (SD) states in Gadolinium and Dysprosium isotopes were produced via heavy-ion induced reactions and studied with the (EUROGAM EUROpean GAmma-ray Microscope) gamma multidetector array. Precise level attenuation method (DSAM). From the derived quadrupole moments, we find large differences in deformation between the yrast bands in neighbour nuclei explained in terms of the case of nuclei corresponding to an axis ratio of 2:1, the shell gaps are not fixed at a specific particle number and deformation. Furthermore the present results indicate that the deformations associated with identical bands are different supporting the picture that mass and deformation changes tend to compensate in SB bands with the same moments of inertia. (author). 114 refs.

International Nuclear Information System (INIS)

For safety evaluations and licensing procedures, fuel rod performance is predicted through model calculations. Due to the complexity of fuel rod performance and the insufficient availability of experimental data, such calculations necessarily reflect inaccuracies and conservatism. For verification and development of more realistic models and submodels, acquisition of reliable on-line data on fuel rod performance characteristics is imperative. The present paper describes the instruments and equipment applied in the Halden Reactor for on-line measurements of fuel rod and assembly power and power distribution, and fuel rod axial and diameter deformation. Recent results from evaluation of such fuel rod deformation measurements, covering fuel rods with different designs, subjected to various modes of operation, including startup ramps, steady state, and power shock, are presented. It is also shown how these data are used for verification and ...

UK PubMed Central (United Kingdom)

Equinovarus of the foot is the most common lower extremity deformity following traumatic brain injury. We evaluated outcomes of the split anterior tibialis tendon transfer (SPLATT) for correction of...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The cell is modeled as an ellipsoid with shell and the surface stress distribution calculated by means of the Maxwell Stress Tensor. The cell membrane is treated as incompressible material having both bending and shear energies of deformation. Employing the principle of virtual work, cell volume (and hence shape) is computed as a function of the external field strength and orientation with respect to the field. The following results were obtained: (1) The surface stresses that develop or the cell membrane are distributed having both normal and tangential components that act together to produce a rounding of the cell. (2) If the tangential component of the stress is ignored, then higher field strengths are needed to produce similar deformation (shape change) of cells. (3) The threshold value of the applied field, i.e, the field strength at which the volume (shape) of the cell changes abruptly, occurs at approximately 55V/cm. Above the threshold ...

Energy Technology Data Exchange (ETDEWEB)

Methodologies are given for conducting studies to discover and map break deformations in coal strata using various modifications on radiometry, together with the field for their use. Results that were obtained using the IKS-50 device are given.

Energy Technology Data Exchange (ETDEWEB)

The deformation characteristics of pellets of electrolyte-binder (EB) mixes based on MgO were measured under simulated, thermal-battery conditions. Measurements (using a statistically designed experimental strategy) were made as a function of applied pressure, temperature, and percentage of theoretical density for four molten-salt electrolytes at two levels of MgO. The EB mixes are used as separators in Li-alloy thermal batteries. The electrolytes included LiCl-KCI eutectic, LiCl-LiBr-KBr eutectic, LiBr-KBr-LiF eutectic, and a LiCl-LiBr-LiF electrolyte with a minimum-melting composition. The melting points ranged from 313 C to 436 C. The experimental data were used to develop statistical models that approximate the deformation behavior of pellets of the various EB mixes over the range of experimental conditions we examined. This report, discusses the importance of the deformation response surfaces to thermal-battery design.

UK PubMed Central (United Kingdom)

A new 3D model is developed to simulate the self-oscillation of the elongated vocal folds. This model allows for large deformation and longitudinal displacement. The displacement boundary condition...Full Text Available

CERN Document Server

We calculate quark-antiquark potentials using the relationship between the expectation value of the Wilson loop and the action of a probe string in the string dual. We review and categorize the possible forms of the dependence of the energy on the separation between the quarks. In particular, we examine the possibility of there being a minimum separation for probe strings which do not penetrate close to the origin of the bulk space, and derive a condition which determines whether this is the case. We then apply these considerations to the flavoured resolved deformed conifold background of Gaillard et al. We suggest that the unusual behaviour we observe in this solution is likely to be related to the IR singularity which is not present in the unflavoured case.

International Nuclear Information System (INIS)

We analyse in detail the SL(2, R) black hole by extending standard techniques of Kac-Moody current algebra to the non-compact case. We construct the elements of the ground ring and exhibit W_#infinity# type structure in the fusion algebra of the discrete states. As a consequence, we can identify some of the exactly marginal deformations of the black hole. We show that these deformations alter not only the spacetime metric but also turn on non-trivial backgrounds for the tachyon and all of the massive modes of the string. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The schematic model is extended to open-shell nuclei. The quasiparticle random-phase approximation plus core polarization are used to calculate multipole matrix elements M/sub n/ and M/sub p/. Calculated trends in the ratio of deformation parameters ..beta../sub n//..beta../sub p/ are compared with experimental ratios for several sets of isotopes and isotones. The systematics indicate a rather abrupt change toward equality of ..beta../sub n/ and ..beta../sub p/ when N or Z is changed from a closed-shell value.

Energy Technology Data Exchange (ETDEWEB)

Posttraumatic tibia valga is a well-recognized complication following fracture of the upper tibial metaphysis in young children. We present a case of a child who developed a valgus deformity following fracture of the proximal tibia and fibula in which quantitative bone scintigraphy at 5 months after injury demonstrated increased uptake at the proximal tibial growth plate with proportionally greater uptake on the medial side. This finding suggests that the valgus deformity in this patient was due to a relative increase in vascularity and consequent overgrowth of the medial portion of the proximal tibial physis.

CERN Document Server

The possibility of the existence of stable tetrahedral deformations at spin zero is investigated using the Skyrme-HFBCS approach and the generator coordinate method (GCM). The study is limited to nuclei in which the tetrahedral mode has been predicted to be favored on the basis of non self-consistent models. Our results indicate that a clear identification of tetrahedral deformations is unlikely as they are strongly mixed with the axial octupole mode. However, the excitation energies related to the tetrahedral mode are systematically lower than those of the axial octupole mode in all the nuclei included in this study.

Energy Technology Data Exchange (ETDEWEB)

This study examines the effects of blasting on waste dumps at open pit mining operations. Of specific concern were mining operations at the base of a five hundred foot high waste dump such as the operation at the South Pit of the Smoky-River Coal Ltd. property near Grande Cache, Alberta. An assessment of waste dump stability including factors such as quasi-static deformation behaviour, historical dump deformation behaviours and potential blasting effects was undertaken. It is concluded that safe blasting may be carried out in proximity to waste dumps, but monitoring of dump behaviour is recommended to ensure operational safety. 22 refs., 4 apps.

Science.gov (United States)

This study deals with the torsional response of Ti-8823 and 18Ni (200) maraging steel. The effect of different heat treatments and the subsequent change in microstructure are investigated. In the case of the Ti-8823, a comparison was made between the solu...

International Nuclear Information System (INIS)

In the heat-affected zones (HAZ) of low alloy steels used for nuclear pressure vessel, microstructural changes, such as grain coarsening, carbide precipitation, and martensite formation, generally occur and cause a deterioration of toughness and an increase in sensitivity to brittle fracture. Metallographic analyses of low alloy steel welds reveal significantly different regions in HAZ microstructures. In 2-pass welds, there were seven characteristic regions in the HAZ determined by the peak temperature, to which the region was exposed during the weld thermal cycle: a coarse-grained region, a fine-grained region, an intercritical region, and subcritical region. The coarse-grained region can be categorized into four zones according to the reheating temperature as follows : an unaltered coarse-grained zone (UCGHAZ), a supercritically reheated coarse grained zone (SCRCGHAZ), an intercritically reheated coarse-grained zone (ICRCGHAZ), and an ...

Energy Technology Data Exchange (ETDEWEB)

A micro-mechanistic understanding of bone fracture thatencompasses how cracks interact with the underlying microstructure anddefines their local failure mode is lacking, despite extensive research nthe response of bone to a variety of factors like aging, loading, and/ordisease.

International Nuclear Information System (INIS)

The development of tough #alpha#-SiAlON with elongated grains in the last five years is summarized. This progress has been guided by the improved understanding of phase relations and nucleation/growth kinetics in SiAlON ceramics. Although most #alpha#-SiAlON compositions can be processed to contain some elongated grains, their microstructure, fracture toughness and R-curve behavior vary greatly. Such variability is due to the different phase stability of #alpha#-SiAlONs and the varying physical chemistry of the competing phases, including the transient/residual liquid. For this reason, microstructure control of #alpha#-SiAlON must pay close attention to the composition, starting powder and heating schedule. Seeding with single crystals of an appropriate #alpha#-SiAlON composition provides an attractive alternative that simplifies the task of microstructure control, since such seeds are thermodynamically stable and they ...

Energy Technology Data Exchange (ETDEWEB)

Cold deformation of YBa{sub 2}Cu{sub 3}O{sub 7-x}(phase 123, T{sub c} = 88.5-92 K) powders and strips causes partial decomposition of the 123 phase, a reduction in the degree of orthorhombicity of the structure up to almost complete degradation, and a decrease in T{sub c}. When they are deformed, yttrium high temperature superconductors acquire basal (001) (110) texture with high pole density (13-15 arbitrary units), low scattering angle ({+-} 6deg--7deg from the normal direction), and a weak preference for a, b or a + b in the rolling direction; traces of (139) orientations may also be found. This texture is known to be favourable for increasing j{sub k}. The combined effect of cold deformation and a carbon-containing binder leads, however, to a complete loss of superconductivity at 77 K or above. Depending on the regime of subsequent annealing, the following effects may be observed: degradation of the orthorhombic ...

Energy Technology Data Exchange (ETDEWEB)

Mixed microstructures have been studied in low- carbon microalloyed steels suitable for automotive applications, after continuous cooling from the hot-rolled condition. Microstructural features such as polygonal ferrite, bainitic and acicular ferrite and microphase constituent are identified using transmission electron microscopy. The influence of these mixed structures on the tensile strength, impact toughness and fracture behaviour is examined. It is found that improvements in impact toughness as compared with microalloyed medium- carbon ferrite/pearlite steels can be achieved from these predominantly acicular structures developed by controlling alloy composition and continuous cooling of these lower carbon steels. (orig.).

International Nuclear Information System (INIS)

Beta-C trademark is a metastable beta titanium alloy which can be heat treated to achieve a good combination of properties such as tensile strength, fatigue strength, ductility and toughness, such as needed in aircraft fasteners. Variations in hot and cold processing parameters and solution heat treatment can affect the resultant grain structure which in turn affects subsequent aging response and mechanical properties. Several processing/heat treating routes on round bar are explored in this study to determine the effects on microstructure and various mechanical properties.

International Nuclear Information System (INIS)

The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society

Science.gov (United States)

Coke petrography could be useful for improving blast furnace coke properties and for solving cokemaking production problems. To do this, quantitative correlations between coke structure, coal properties and carbonization conditions, and coke properties are useful, if not essential. Some examples of correlations of this type were presented in this paper. Specifically, microstructural parameters of cokes produced in Inland Steel Company's pilot scale coke oven were correlated with the rank and blend proportions of the parent coal, with the reactivity of the coke, and with the ASTM stability of cokes prepared from single coals.

Energy Technology Data Exchange (ETDEWEB)

A large part of mechanical and durability characteristics of cement-based materials comes from the performances of the hydrated cement, cohesive matrix surrounding the granular skeleton. Experimental studies, in situ or in laboratory, associated to models, have notably enhanced knowledge on the cement material and led to adapted formulations to specific applications or particularly aggressive environments. Nevertheless, these models, developed for precise cases, do not permit to specifically conclude for other experimental conclusions. To extend its applicability domain, we propose a new evolutive approach, based on reactive transport expressed at the microstructure scale of the cement. In a general point of view, the evolution of the solid compounds of the cement matrix, by dissolutions or precipitations, during chemical aggressions can be related to the pore solution evolution, and this one relied to the ionic exchanges with the external environment. By the ...

Energy Technology Data Exchange (ETDEWEB)

The results of X-ray and neutron diffraction experiments on molten alkali halides in which some data of our experiments by X-ray diffraction such as those of molten LiCl, NaCl, KCl, LiBr and KBr are included were summarized. The first peak positions in the radial distribution function in molten alkali halides by X-ray or neutron diffraction experiments are always longer than those by computer simulations and the differences of 0.1 -- 0.3 A exceed the experimental error. It seems to be due to the deformation of the electron shell. In the computer simulation, the shell model which has the spherical deformation was expected to have a closer value of the first peak position to the experimental one than the rigid ion model by taking the polarization of ions. However, no change in the first peak position was found. Therefore, the non-spherical deformation of electron shell at the point where ions are in contact with each other ...

International Nuclear Information System (INIS)

Mechanical properties of cold-worked molybdenum, grade 4 titanium, and an #alpha#-#beta# titanium alloy are measured with tensile tests and by indentations using conical indenters with 105, 120, and 137 deg included angles. The extent of plastic deformation and pileup around an indentation is measured using profilometry. Various models predicting the extent of plastic deformation and pileup are compared to the actual measured values. As inferred from indentation, the calculated yield strength of the material from the mean pressure does not correlate well to the yield strength measured by tensile testing. The plastic zone size surrounding an indentation can also be used to determine the yield strength of the material, and this does correlate to the yield strength measured by tensile tests. Furthermore, the extent of plastic deformation is relatively independent of the included angle of the indenter for the range of materials ...

Energy Technology Data Exchange (ETDEWEB)

Precisely measured differential cross sections for elastic and inelastic scattering from 104 MeV alpha-particles by /sup 48/Ca, /sup 50/Ti and /sup 52/Cr are reported. The analyses aim primarily at the determination of strength, radial shapes and deformation of the scattering potentials, looking for isotonic differences of N=28 isotones. The mean square radii of the (real) potentials are discussed in terms of mean square radius differences of the matter distributions. The isoscalar transition rates derived by coupled channel analyses of the measured cross sections are compared with electromagnetic rates. In addition to the analyses on the basis of a slightly generalized extended optical model a semi-microscopic deformed folding model has been applied, using a density-dependent effective alpha-bound nucleon interaction. Though an excellent description of the data over the full angular range is obtained the resulting values of the ...

Energy Technology Data Exchange (ETDEWEB)

Deformation in the overburden proves useful in deducing spatial and temporal changes in the volume of a producing reservoir. Based upon these changes we estimate diffusive travel times associated with the transient flow due to production, and then, as the solution of a linear inverse problem, the effective permeability of the reservoir. An advantage an approach based upon travel times, as opposed to one based upon the amplitude of surface deformation, is that it is much less sensitive to the exact geomechanical properties of the reservoir and overburden. Inequalities constrain the inversion, under the assumption that the fluid production only results in pore volume decreases within the reservoir. We apply the formulation to satellite-based estimates of deformation in the material overlying a thin gas production zone at the Krechba field in Algeria. The peak displacement after three years of gas production is approximately ...

Energy Technology Data Exchange (ETDEWEB)

Together with an investigation on the deformation behavior of hot and cold rolled strip edge, the edge-drop control was explained in characteristics and result of application to the commercial mill by the tapered-crown work roll (WR) shifting mill. From a cold rolling experiment, three-dimensional material flow was known to be generated in the vicinity of edge also at the time of rolling the strip, and which generation influences that of edge-drop. Almost linearly relative to the flattened deformation of WR, the edge-drop enlarges with enlargement in that deformation. The number of stands to be applied to the tapered-crown WR shifting mill in the tandem cold mill is determined by the location as far as which the strip is to be controlled in edge-drop. In case of improving it to obtain the edge-drop-free strip, all the stands are required to be equipped with tapered-crown WR shifting mill. By applying a tapered-crown WR ...

Energy Technology Data Exchange (ETDEWEB)

The constitutive model used to describe the deformation of crushed salt is presented in this report. Two mechanisms -- dislocation creep and grain boundary diffusional pressure solution -- are combined to form the basis for the constitutive model governing the deformation of crushed salt. The constitutive model is generalized to represent three-dimensional states of stress. Upon complete consolidation, the crushed-salt model reproduces the Multimechanism Deformation (M-D) model typically used for the Waste Isolation Pilot Plant (WIPP) host geological formation salt. New shear consolidation tests are combined with an existing database that includes hydrostatic consolidation and shear consolidation tests conducted on WIPP and southeastern New Mexico salt. Nonlinear least-squares model fitting to the database produced two sets of material parameter values for the model -- one for the shear consolidation tests and one for a ...

Energy Technology Data Exchange (ETDEWEB)

The thermomechanical behaviour of clayey soils was examined in a laboratory study because of their importance in some engineering applications such as hydrocarbon extraction from oil-bearing sands and radioactive waste disposal. The slightest temperature variations have been known to have an impact on the mechanical behaviour of clayey soils. In this study, tests were conducted on reconstituted and natural clayey soils using triaxial cells modified to control temperatures. Changes of temperature and stress state were not applied simultaneously. Instead, the tests were divided into two separate sections aimed at studying the thermal and mechanical behaviour of clays. The thermal behaviour tests examined the deformations induced by drainage temperature changes as well as pore-pressure generation and consolidation phenomena. The mechanical behaviour tests, focused on the influence of temperature and temperature history on compressibility, ...

International Nuclear Information System (INIS)

Research highlights: ? Correlations between microstructure and internal stress during Ti anodising are established. ? Large internal compressive stresses are accumulated in the film during anodising upto 12 V. ?A transition from compressive to tensile stress is observed when the cell voltage exceeds 12 V. ? At 40 V, the oxide films consist of two regions with different compositions and microstructures. Crystallisation of amorphous to anatase TiO2 contributes to the compressive stress relaxation. - Abstract: The relationship between the microstructural and internal stress evolution during Ti anodising is discussed. Samples anodised galvanostatically to 12 V and 40 V, corresponding to different stages of the internal stress evolution, were examined by in-plane and cross-section transmission electron microscopy. Electron diffraction patterns have been complemented with stoichiometry data obtained from energy loss near edge ...

International Nuclear Information System (INIS)

A dilute tungsten heavy alloy consisting of 50W-35Ni-15Fe (wt pct) was liquid phase sintered at 1,500 C for times ranging from 30 to 960 minutes. This alloy corresponds to a nominal solid content of 20 vol pct at the sintering temperature. Because of the excess liquid, the alloy densified easily and exhibited extensive liquid-solid separation due to the density difference between the phases. The solid content at the compact bottom ranged from 45 to 70 vol pct over position and time. The microstructure of the settled region was quantified for volume fraction of tungsten, grain size, connectivity, and settled solid angle of repose. These results provide a basis for extending the microstructural parameters to possible microgravity conditions. The grain growth rate constant varies with the inverse 2/3 power of the volume fraction of liquid, possibly reflecting combined coalescence and solution-reprecipitation processes. This volume-fraction effect ...

Science.gov (United States)

The papers contained in this volume provide an overview of recent theoretical and experimental research related to the fracture toughness and fatigue crack growth characteristics of titanium alloys. Topics discussed include room temperature fatigue crack propagation in beta-titanium alloys, fatigue crack growth rate acceleration in alpha+beta Ti alloys, influence of transformed beta microstructures on fatigue crack growth rates in Ti-6Al-4V, and the role of inclusion and pore content on the fracture toughness of powder processed blended elemental Ti-10V-2Fe-3Al. Papers are also presented on fatigue crack growth measurements in an alpha-beta titanium alloy, the effects of thermal processing variation on the properties of Ti-6Al-4V, and the effect of microstructure on ductility and fracture toughness of alpha+beta titanium alloys.

Energy Technology Data Exchange (ETDEWEB)

A micro-mechanistic understanding of bone fracture that encompasses how cracks interact with the underlying microstructure and defines their local failure mode is lacking, despite extensive research on the response of bone to a variety of factors like aging, loading, and/or disease. Micro-mechanical models for fracture incorporating such local failure criteria have been widely developed for metallic and ceramic materials systems; however, few such deliberations have been undertaken for the fracture of bone. In fact, although the fracture event in mineralized tissues such as bone is commonly believed to be locally strain controlled, until recently there has been little experimental evidence to support this widely held belief. In the present study, a series of in vitro experiments involving a double-notch bend test geometry are performed in order to shed further light on the nature of the local cracking events that precede catastrophic fracture in bone and to define ...

International Nuclear Information System (INIS)

Ca #alpha#-sialon is a high hardness material that exhibits in-situ growth of elongated grains during pressureless sintering. This potentially gives the material very good fracture toughness. This paper examined the effects of a number of variables on microstructural development during sintering. The effect of composition was investigated by studying seven different compositions. Densification was seen to be hindered in compositions that produced only small quantities of liquid phase during sintering. Elongated #alpha#-sialon was observed in all the compositions. It was in combination with equiaxed #alpha#--sialon in low liquid compositions, but only elongated #alpha#-sialon was present in the liquid rich compositions. The effects of using P-Si_3N_4 instead of #alpha#-Si_3N_4 starting powders were also examined. Compositions using only #alpha#-S_3N_4 and those that used a 50:50 #alpha#:#beta# mix displayed similar development during sintering. However, compositions ...

Energy Technology Data Exchange (ETDEWEB)

(001) CZ silicon wafers were implanted with arsenic (As{sup +}) at energies of 10--50 keV to doses of 2 {times} 10{sup 14} to 5 {times} 10{sup 15}/cm{sup 2}. All implants were amorphizing in nature. The samples were annealed at 700 C for 16 hrs. The resultant defect microstructures were analyzed by XTEM and PTEM and the As profiles were analyzed by SIMS. The As profiles showed significantly enhanced diffusion in all of the annealed specimens. The diffusion enhancement was both energy and dose dependent. The lowest dose implant/annealed samples did not show As clustering which translated to a lack of defects at the projected range. At higher doses, however, projected range defects were clearly observed, presumably due to interstitials generated during As clustering. The extent of enhancement in diffusion and its relation to the defect microstructure is explained by a combination of factors including surface recombination of point defects, As ...

International Nuclear Information System (INIS)

The microstructures of so called high temperature alloys, which have been developed for service temperatures up to 800"0C, are not necessarily stable at higher temperatures. The mobility of alloying elements is very high in FeCrNi alloys at 950 "0C e.g. iron, chromium or nickel can diffuse up to 0.1 mm distance in one year, which is about a grain diameter. Interstitials like carbon or nitrogen show a four orders of magnitude higher diffusivity than the alloying elements. In addition, the carbon solubility in this type of alloy is reported to be very low. Therefore the alloys are supersaturated with carbon after heat treatment above 1100 "0C and water quenching although the absolute carbon content is very low. At service temperatures around 800"0C the solubility of carbon is still about one order of magnitude lower than at heat treatment temperature. This will lead, together with the high mobility of elements, to precipitation of carbides even after short times and ...

International Nuclear Information System (INIS)

Ferritic/martensitic steel, modified 9Cr-1Mo steels have been used most extensively in the power generation industry throughout the world due to having superior high temperature properties such as high strength, creep resistance, and good microstructure stability. These steels are also the primary candidate for the RPVs(Reactor Pressure Vessels) of High Temperature Gas-Cooled Reactors. Currently, many studies has been conducted in laboratory-scale for mod. 9Cr-1Mo steels. However, there is a lack of the study on forged thick- section for RPVs. The differences in characteristics including the through thickness microstructure and mechanical properties between internal and external locations may occur during cooling after austenitization, because the thickness of RPVs is over about 200mm. Therefore, in order to use ferritic/martensitic steel as RPVs, a detailed assessment of the through thickness properties is needed. The purpose of this study is ...

International Nuclear Information System (INIS)

We examined the spectral behaviors of lasing from a asymmetrically deformed liquid jet (a ? 14 ?m) which is induced by a laterally flowing gas. Th liquid sample was methanols which contains DCM dye. When n distortion is induced, the lasing spectrum appears as two periodic peaks which are corresponding to the resonance modes of cylindrical cavity. As the distortion parameter exceeds about 4%, the lasing spectrum shifts continuously to short wavelength. When the distortion parameter reaches ? 10%, the amount of blue shift was ? 30 nm. The blue shift can be explained as the shift of optimum wavelength of threshold curves. From the absorption and fluorescence curve of liquid sample, we estimated the spoiled Q with the distortion parameter.

British Library Electronic Table of Contents (United Kingdom)

In this study polycrystalline specimens of as-cast DyCu with B2 crystal structure were compressed to different strains at room temperature to test if stress-induced phase transformation and twinning occur during deformation. In these tests DyCu exhibited high ductility with plastic strain as high as 35% and ultimate compressive strength of ~790MPa. X-ray diffraction and transmission electron microscopy (TEM) showed no indications that DyCu had undergone stress-induced phase transformation or twinning. -type dislocations have been observed to play an important role for imparting the ductile behavior. TEM analyses showed the presence of second phases, Dy2O3 and DyCu2 within the DyCu. The mechanisms of ductility and impurity phase formation are discussed.

British Library Electronic Table of Contents (United Kingdom)

Post-tensioned (PT) self-centering moment frames have been developed as an alternative to typical moment-resisting frames (MRFs) for earthquake resistance. When a PT frame deforms laterally, gaps between the beams and columns open. However, the gaps are constrained by the columns and the slab in a real PT self-centering building frame. This paper presents a methodology for evaluating the column restraint and beam compression force based on the column deformation and gap openings at all stories. The method is verified by cyclic tests of a full-scale, two-bay by one-story PT frame. Moreover, a sliding slab is proposed to minimize restraints on the expansion of the PT frame. Shaking table tests were conducted on a reduced-scale, two-by-two bay one-story specimen, which comprises one PT frame ...

CERN Document Server

To investigate the origin and nature of inertia, we introduce a new concept of hypothetical 2D, so-called, "master-space" (MS), subject to certain rules. The MS, embedded in the background 4D-spacetime, is an indispensable individual companion to the particle of interest, without relation to every other particle. We argue that a deformation/(distortion of local internal properties) of MS is the origin of inertia. With this perspective in sight, we construct the alternative relativistic theory of inertia (RTI), which allows to compute the relativistic inertial force acting on an arbitrary point-like observer due to its "absolute acceleration". We go beyond the hypothesis of locality with an emphasis on distortion of MS, which allows to improve essentially the standard metric and other relevant geometrical structures related to the noninertial reference frame of an arbitrary accelerated observer. We compute the inertial force exerted on the photon in a gravitating ...

Energy Technology Data Exchange (ETDEWEB)

The authors consider the dynamics of interacting elastic disks in the plane. This is an experimentally realizable two-dimensional model of dry granular flow where the stresses can be visualized using the photoelastic effect. As the elastic disks move in a vacuum, they interact through collisions with each other and with the surrounding geometry. Because of the finite propagation speed of deformations inside each grain it can be difficult to capture computationally even simple experiments involving just a few interacting grains. The goal of this project is to improve our ability to simulate dense granular flow in complex geometry. They begin this process by reviewing some past work, how they can improve upon previous work. the focus of this project is on capturing the elastic dynamics of each grain in an approximate, computationally tractable, model that can be coupled to a molecular dynamics scheme.

British Library Electronic Table of Contents (United Kingdom)

Regularities of deformation-induced dissolution of a surface layer of iron oxides in matrixes of iron-based alloys with bcc and fcc lattices have been studied by the methods of M?ssbauer spectroscopy, transmission electron microscopy, and X-ray diffraction. A method of producing iron alloys strengthened by dispersed oxide nanoparticles and alloyed with elements possessing a high affinity to oxygen (titanium and yttrium) has been proposed, which implies a dynamic dissolution of a surface layer of iron oxides upon strong cold deformation and a precipitation of secondary yttrium and titanium nanooxides upon a subsequent high-temperature sintering of mechanically alloyed powders. There has been demonstrated a possibility of oxide strengthening of pure iron upon its interaction with air without...

International Nuclear Information System (INIS)

General expressions for the interlattice displacements of the A-15 structure compounds are obtained in terms of the strain components making use of the deformation theory. The nature of the interlattice displacements of all the 8 atoms in the unit cell is discussed. It is found that the interlattice displacements occur in such a way that the pair of atoms along any linear chain move in opposite directions with equal magnitudes. Expression for the strain energy of these compounds is developed using deformation theory and this is compared with the strain energy expression from continuum theory to obtain the elastic constants. The theoretical values of the elastic constants fairly agree with the experimental values for V_3Si, V_3Ge and Nb_3Sn. (author).

Energy Technology Data Exchange (ETDEWEB)

This paper presents experimental data and an computational model of the cold spray solid particle impact process. Copper particles impacting onto a polished stainless steel substrate are examined. The high velocity impact causes significant plastic deformation of both the particle and the sub- strate, but no melting is observed. The plastic deformation exposes clean surfaces that, under the high impact pressures, result in significant bond strengths between the particle and substrate. Experimental measurements of the splat and crater sizes compare well with the numerical calculations. It is shown that the crater depth is significant and increases with impact velocity. However, the splat diameter is much less sensitive to the impact velocity. It is also shown that the geometric lengths of the splat and crater scale linearly with the diameter of the impacting particle. It is hoped that the results presented will allow better understanding of the ...

International Nuclear Information System (INIS)

High temperature deformation behavior of an alpha + beta titanium alloy Ti-3Al-2.5V has been investigated in the temperature range 830 deg. C to 910 deg. C by using the method of cross head speed cycling. On the basis of flow stress-strain rate and strain rate sensitivity data, it was found that the alloy exhibits a hardening effect in the entire temperature range studied, amount of hardening being significant at the highest test temperature of 910 deg. C which resulted in a degradation of superplastic properties of the alloy. Grain growth in beta-phase due to strain was considered responsible for the hardening effect observed.

British Library Electronic Table of Contents (United Kingdom)

Tissue-engineered heart valves are prone to early structural deterioration. We hypothesize that cell?scaffold interaction and mechanical deformation results in upregulation of genes related to osteogenic/chondrogenic differentiation and thus changes extracellular matrix (ECM) composition in human bone marrow mesenchymal stem cell (hBMSC)-derived tissue-engineered grafts. hBMSC were expanded and seeded onto poly-glycolic acid/poly-lactic acid scaffold for 14 days. Seeded tissue-engineered constructs (TEC) were subjected to cyclic flexure for 24?h, whereas control TEC was maintained in roller bottles for the same duration. hBMSC, TEC, and mechanically deformed TEC were subjected to gene-array and histological analysis. Expression levels of RNA and/or protein markers related to chondrogenesis...

British Library Electronic Table of Contents (United Kingdom)

In many drug dispensing devices, such as syringes and inhalers, an elatomeric gasket is used to prevent the formulation from leaking from the chamber. During device actuation, the seal is subjected to friction, which in turn causes its deformation and can cause unintentional leakage, thus dose variability. Additionally, friction of seal is responsible for a host of potential problems such undue effort required for actuation and potential wear. The mechanism of friction generation in the seal conjunction is complex, arising from adhesion of rubber in contact with the moving interface, viscous action of a thin film of fluid and deformation of seal asperities. Therefore, the first step in understanding the conjunctional behaviour of rubber seals is a fundamental study of mechanisms of frictio...

British Library Electronic Table of Contents (United Kingdom)

The experimental results of brittle/ductile two-layer analogue models verify that intraplate tectonic deformation in central-eastern Asia is controlled mainly by the netlike plastic-flow (NPF) occurring in the lower lithosphere, including the lower crust and lithospheric mantle. The ductile lower layer in the model, corresponding to the lower lithosphere in the natural prototype, is made of a mixture of gum rosin and turpentine oil and the brittle upper one, to the upper crust, is formed by the consolidation of talc-powder slurry. The NPF hypothesis for continental dynamics can be regarded as a combination and development of two kinds of seemingly mutually exclusive ones, which are based on the theories of slip-line field and viscous (plastic) flow, respectively. In contrast to "homogeneou...

Energy Technology Data Exchange (ETDEWEB)

The effect of tsub(A) austenitization temperature in heating for quenching as well as in the cycle of high-temperature thermomechanical treatment (HTMT) on structure, mechanical properties and fracture mode of 40KhN2MA structural steel is investigated. It is shown that heating up to 1200 deg C does not affect essentially sigmasub(b) and sigmasub(0.2) of a quenched material but increases fracture toughness of 200 deg C - tempered precracked specimens and is accompanied by a decrease of impact strength and plasticity of vee-notched specimens. The optimum complex of mechanical properties is attained upon combined treatment comprising heating up to 1200 deg C and HTMT with deformation at 850 deg C.

International Nuclear Information System (INIS)

An Ultra-Low-Carbon 19% Cr-11% Ni Stainless Steels used in nuclear fuel reprocessing plants where highly corrosion resistance in nitric acid is required has been developed. This steel has optimized the chemistry composition to decrease inclusions and deformation-induced martensitic transformation. The formation of deformation-induced martensite has the potential danger of accelerating corrosion in nitric acid. In this paper, effects of cold reduction and martensitic transformation on corrosion resistance of Ultra-Low-Carbon Stainless Steels in nitric acid are discussed. The developed steel showed excellent corrosion resistance during long-term exposure to nitric acid. (author).

Energy Technology Data Exchange (ETDEWEB)

Rafting of the {gamma}/{gamma}{prime} morphology of nickel-base superalloys is a well-known phenomenon during high-temperature deformation. The initial stages of this type of directional coarsening were modeled two-dimensionally by the method of finite elements (FEs) using an energy-perturbation approach. In addition to the elastic energy density, the effect of the local difference of the hydrostatic stresses in {gamma} and {gamma}{prime} in combination with the different lattice parameters of the two phases was considered in the calculations as a further driving force. From the results of modeling, the deformation-induced internal stresses and strains were determined and used to evaluate the direction-dependent lattice parameters and lattice misfits of the two phases. The results agree well with experimentally determined values.

British Library Electronic Table of Contents (United Kingdom)

Abstract: We have performed petrographic and spectroscopic studies of brown diamonds from an eclogite xenolith from the Udachnaya pipe (Yakutia, Russia). Brown diamonds are randomly intermixed with colorless ones in the rock and often located at the grain boundaries of clinopyroxene and garnet. Brown diamonds can be characterized by a set of defects (H4, N2D and a line at 490.7nm) which are absent in colorless diamonds. This set of defects is typical for plastically deformed diamonds and indicates that diamonds were likely annealed for a relatively short period after deformation had occurred. Excitation of brown colored zones with a 632.8nm He-Ne laser produced the typical diamond band plus two additional bands at 1730cm^-^1 and 3350cm^-^1. These spectral features are not genuine Raman ban...

International Nuclear Information System (INIS)

The changes in microstructure of a specially prepared boron nitride (BN) film as a function of film depth were studied by high resolution transmission electron microscopy (HRTEM) and other materials analysis tools. These changes were then correlated to the changes in processing parameters during film growth. The analyzed film was fabricated by the four-step ion-assisted deposition procedure known to be effective in film-stress engineering for the formation and retention of a thick cubic BN (cBN) layer with a three-step buffer-layer deposition. In this deposition, the energy of the ions assisting cBN formation was increased stepwise from 200 to 280, and then to 360 eV [S.F. Wong, C. W. Ong, G.K.H. Pang, K.Z. Baba-Kishi, W. M. Lau, J. Vac. Sci. Technol. A 22 (2004) 676]. The nominal thickness of the cBN layer was 650 nm and that for each of the three buffer layers was about 160 nm. Both the HRTEM and electron diffraction results confirmed that the top cBN layer, with ...

International Nuclear Information System (INIS)

In this paper, the influence of plasma nitriding at temperature 720 deg. C for 20 h on the surface microstructure and interface microstructure of electroplated chromium coating was investigated. In these conditions, interdiffusion, mixing and reaction phenomena of elements originating from the substrate and coating material are more likely to occur, thus increasing the bonding strength between the coating and carbon steel substrate. The change of the structures from the substrate side to the coating surface, and the effect of the substrate steel on the interface structure were studied by cross-sectional transmission electron microscope observation (XTEM). The nitride layer formed on the surface was analyzed by X-ray diffraction method (XRD). After treatment at above conditions a 6-7 #mu#m thick nitride compound layer was formed in surface region and the same thick carbide compound layer was also formed in the interface region between ...

International Nuclear Information System (INIS)

Microstructure characterization is important for controlling the quality of laser welding. In the present work, a detailed microstructure characterization by transmission electron microscopy was carried out on the laser welding cast Ni-based superalloy K418 turbo disk and alloy steel 42CrMo shaft and an unambiguous identification of phases in the weldment was accomplished. It was found that there are #gamma#-FeCrNiC austenite solid solution dendrites as the matrix, (Nb, Ti) C type MC carbides, fine and dispersed Ni_3 Al #gamma#' phase as well as Laves particles in the interdendritic region of the seam zone. A brief discussion was given for their existence based on both kinetic and thermodynamic principles.

British Library Electronic Table of Contents (United Kingdom)

Pulses are rich in nutrients. The existence of anti-nutritional components and the length of time required for preparation have, however, limited their frequency of use compared to recommended intake levels. Anti-nutritional components in pulses can be largely removed by heat treatment. Additionally pre-treatment of pulses with heat and processing of seeds into flour could further enhance their use by decreasing processing and preparation times. In this study, trypsin inhibitor activity, functional properties, and microstructural characteristics of flours prepared from different varieties of lentil, chickpea, and pea as affected by roasting and boiling were evaluated. Both thermal treatments resulted in significant reduction (p<0.05) in trypsin inhibitor activity ranging from -95.6% to -37...

British Library Electronic Table of Contents (United Kingdom)

The influence of selenium dioxide (SeO2) on the microstructure and electrodeposition of manganese coatings obtained from a sulfate based neutral solution was investigated by material characterization methods and electrochemical techniques. The crystal structure and surface morphology of these coatings were studied by scanning electron microscopy (SEM) and powder X-ray diffraction spectroscopy (XRD), respectively. The SEM and XRD data showed that SeO2 could effectively accelerate phase transformation, and facilitate leveled and fine grain growth. The electrochemical results indicated that SeO2 could inhibit hydrogen evolution reaction and promote manganese deposition. The action of selenium dioxide in manganese deposition was found to be a reduction and adsorption mechanism. The process cou...

Energy Technology Data Exchange (ETDEWEB)

The authors report the fabrication and characterization of a low temperature (200--400 C) thin film gas sensor constructed from a MOCVD-grown yttria-stabilized zirconia (YSZ) layer sandwiched between two platinum thin film electrodes. A reproducible gas-sensing response is produced by applying a cyclic voltage which generates voltammograms with gas-specific current peaks and shapes. Growth conditions are optimized for preparing YSZ films having dense microstructures, low leakage currents, and maximum ion conductivities. In particular, the effect of growth temperature on film morphology and texture is discussed and related to the electrical and gas-sensing properties of the thin film sensor device.

International Nuclear Information System (INIS)

In order to substitute expensive cast titanium alloys by powder ones the possibility of introduction of powder additions by mechanical stock mixing is studied. It is shown that microstructure of powder alloys of Ti-Zr(1-9%) system is typical for one-phase cast #alpha#-alloys. The Ti-Mo(1-9%) and Ti-Nb(1-9%) system alloys have microstructure typical for two-phase (#alpha#+#beta#)-alloys. For homogeneous structure to be obtained the high temprature annealing is advisable after hot pressing. Alloying with Mo, Zr and Nb permits to increase considerable the strength of powder titanium products (at 9% Mo more than two times).

International Nuclear Information System (INIS)

The irradiation behavior of Li_2TiO_3 under a fusion reactor environment was simulated by simultaneous irradiation of Li_2TiO_3 by the triple ion beams and the respective single ion beams of O"2"+, He"+ and H"+. The microstructural changes in Li_2TiO_3 caused by the irradiation were measured by Raman spectroscopy and FT-IR photoacoustic spectroscopy. The results suggest that the formation of TiO_2 due to displacements by irradiation occurs, and the irradiation defects generated by irradiation trap hydrogen and increase the amount of hydroxyl near the surface. Such phenomena are believed to significantly affect the chemical form of the released tritium and the tritium inventory in the breeding materials of a fusion reactor.

Energy Technology Data Exchange (ETDEWEB)

The use of selective additives such as MgO as a sintering aid and a rare earth oxide as a grain growth inhibitor, has allowed the manufacture of beryllia ceramics having close to theoretical density. The grain size and grain size distribution can be controlled by an optimum firing schedule leaving a remnant porosity which is extremely fine (0.2 {mu}m). This structure is compared with conventional BeO ceramics, densified by liquid phase sintering, which develops a glassy grain boundary and retains large pores up to 3 {mu}m. The significantly improved strength properties, extremely fine pores,the 'pinning effect' of rare earth oxide, and the superior surface finish both in the as-fired and polished state are discussed in relation to the micro-structure. (orig.).

International Nuclear Information System (INIS)

Conductive TiN/Si_3N_4 ceramic composites were processed by electrical discharge machining (EDM) and their microstructure and conductivity were investigated. The whole process of tool electrode wear is evaluated by sinker-EDM. The machined surfaces of TiN/Si_3N_4 ceramic composites were examined by scanning electron microscopy (SEM) and profilometry to determine the surface finish. The electrode wear rate of brass is higher than copper electrode for all EDMed tests. The surface texture was found to have greater dependence on pulse energy. It was observed that the sinker-EDM at higher pulse energy caused severe microdamage in the surface. The surface roughness (Ra) values also increase with increasing pulse energy.

International Nuclear Information System (INIS)

Nanometer Ce-W composite materials have been prepared by the method of freeze-drying. Microstructure and surface properties of materials were investigated by SEM and 'in situ' AES and emission characteristics have been determined. It is found that the nanometer materials have relatively small crystal particles with average dimensions in the order of 50 nm. Due to the results of matrix analysis, the cerium in the materials is uniformly distributed on submicron scale, which proves that the diffusion ability of cerium has been increased. Under high temperature, the active layer on the surface thickens simultaneously with the increase of cerium and oxygen. As a result, nanometer Ce-W materials exhibit excellent emission characteristics compared with those of micron-sized Ce-W materials.

Energy Technology Data Exchange (ETDEWEB)

X-Ray reflectivity has been used to investigate the microstructural changes of solution-cast stearic acid films before and after immersion in CoCl{sub 2} solutions. Before immersion, the films possess a well-defined layered structure with an interlayer spacing of 4.01{+-}0.05 nm. After the films were immersed in the CoCl{sub 2} solutions, a new set of equidistant diffraction peaks emerge, the corresponding interlayer spacing of which is 5.13{+-}0.05 nm. The X-ray photoelectron spectra of the films indicate the existence of cobalt ions inside the films after immersion. It is concluded that the permeation of the cobalt ions into the hydrophilic interlayer causes the stearic acid molecules to reorient perpendicular to the films, resulting in the increase of interlayer spacing and the roughening of the interfaces.

British Library Electronic Table of Contents (United Kingdom)

Yb-, Y-, Yb/Y-, and Yb/Nd-doped -SiAlON ceramics with 5-wt% barium aluminosilicate (BAS) were synthesized by hot pressing. Typical self-reinforced microstructures were obtained in all investigated -SiAlONs in spite of the type of doped cations. This is attributed to the incorporation of BAS, which could supply suitable liquid phase to promote the anisotropic growth of the -SiAlON grains. All the composites exhibited excellent high-temperature mechanical properties and thermal shock resistance due to the formation of a self-reinforced microstructure and the complete crystallization of BAS additive.

International Nuclear Information System (INIS)

We studied age-related microstructural changes in the subcortical white matter from adolescence to middle age in 16 healthy male subjects (age range: 12 to 47 years) using diffusion-weighted magnetic resonance (MR) imaging (DWI). Mean diffusivity (MD) of subcortical white matter was mapped onto the overlying cortical surface using our original method. The mean MD values within 76 cortical regions were measured using atlas-based gray matter segmentation and then correlated with age. A significant negative correlation with age was observed in subcortical MD values in several cortical regions, primarily over the bilateral temporal and occipital lobes. Our results demonstrated subcortical microstructural change in postadolescence that may reflect continuing myelination. (author)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

International Nuclear Information System (INIS)

Up to 90% of the life time of cyclically loaded components is determined by short crack initiation and propagation. This stage of the fatigue damage process is strongly influenced by microstructural features, e.g. grain boundaries and crystallographic grain orientation. Therefore LEFM can not be applied in a reasonable manner explaining the demand for a mechanism-related modelling method. The present study deals with mechanical testing and microstructural examinations applied to the relatively new #beta#-titanium alloy LCB. The results are used as data base to develop a new short crack model that is based on the model of Navarro and de los Rios. By using various techniques such as electron back-scattered diffraction and finite-element calculations the origin of crack initiation is revealed and the characteristics of crack propagation is determined. (orig.)

International Nuclear Information System (INIS)

Quantitative analytical electron microscopy study of dopant distribution in the microstructure of selected Nd-#alpha#-sialon samples revealed the presence of relatively large amounts of glassy phase at quadruple pockets, which exhibited a common composition similar to a melilite solution. Al segregants were depleted from adjacent grain boundaries to satisfy the 'stoichiometry' of such glass. Existence of this glass results in significant deviation of the Nd-#alpha#-sialon composition from the expected values, which shifts the #alpha#-#beta#-sialon phase boundary. Only extra Nd_2O_3 additives enable a monolithic #alpha#-sialon microstructure. The absence of similar glass in Yb-#alpha#-sialon materials keeps the phase relations from such deviations.

Energy Technology Data Exchange (ETDEWEB)

Effect of alcohol solvent in mixing process on process on the microstructure and sintering behavior of ceramic-based composites was inestigated in detail. The mixture of fine ceramic powders was prepared through the conventional ball-milling method with various alcohol media. The particle distributions of fine ceramic powders were strongly dependent on the kind of alcohol employed during ball-milling. Ceramic-based composites were fabricated by hot-pressing the mixture of fine ceramic powders. Their microstructures and some mechanical properties of the ceramic-based composites were evaluated. It was found that the viscosity of alcohol, surface tension and contat angle greatly affect the sinterbility and some of the mechanical properties of ceramic-based somposites. (author)

Energy Technology Data Exchange (ETDEWEB)

Recent developments on plastic forming technology of magnesium alloys are presented. Attempts have been undergoing with an aim at forming magnesium alloy parts at lower temperatures. It is believed that fine microstructure magnesium alloys usually have much higher plasticity at lower temperatures and even room temperatures. Extrusion is a method to form magnesium profile products and tube products, which is also one of the effective ways to make fine microstructure magnesium alloys. Superplasticity forming is another method to form high plasticity magnesium alloys. Hot forming of magnesium sheet parts is an important process to form magnesium products. Some developments related to above issues are discussed in the present paper. (orig.)

International Nuclear Information System (INIS)

The examination of the high-temperature properties of the alloy Alloy 800HT has shown that both the creep performance and the microstructure of the material can be purposefully set by the initial heat treatment. At the high temperatures applied, (700-900 C), a rapid softening process sets in induced by carbide precipitation, stabilization, and coarsening. This softening process causes creep velocities strongly accelerating as a function of duration of the heat treatment prior to the creep test. The identified cause of the softening effect is a change in particle size that could be verified by SEM and TEM. It is shown that two different carbide precipitate size classes are responsible for the softening effect. While the precipitates dectable by TEM become effective primarily via interactions with dislocations, the carbide precipitates detectable only by SEM contribute to a hardening of the grain boundaries and the matrix.(orig./CB)

Energy Technology Data Exchange (ETDEWEB)

Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, r-values and their relation to the texture. This correlation ...

Energy Technology Data Exchange (ETDEWEB)

The nuclear shapes of transitional Mo isotopes are calculated by means of a model based on the cranking approximation and the Strutinksy method. The recent experimental results of the high-spin spectroscopy and lifetime measurement of [sup 87]Mo are studied in detail and explained by the evolution of the [gamma]-deformation with the quasiparticle configurations. The shape calculations with the modified-harmonic-oscillator potential give a critical neutron number N [>=] 47 for the spherical shape of the Mo isotopes. (orig.)

Science.gov (United States)

A flutter-motion equation is presently derived for a 2D composite sandwich panel considering the total lateral displacement of the plate as the sum of the displacement due to bending of the plate, and that which is due to shear deformation at the core. The effects of core thickness and stacking sequence of the faces on the flutter boundary of the plate are discussed; it is shown that the sandwich panel greatly improves the flutter boundary over that of a composite laminate panel, provided it has sufficient core thickness.

Energy Technology Data Exchange (ETDEWEB)

Structure of ferrite in drawn pearlitic steel containing 0.9 mass% C was investigated with X-ray diffraction technique using synchrotron radiation. In the detailed analysis of diffraction peaks of ferrite during the drawing process, it was experimentally revealed that the transformation of ferrite from bcc to bct due to the supersaturation of carbon in ferrite of heavily drawn pearlitic steel.

International Nuclear Information System (INIS)

A numerically feasible method, based on the use of deformed phonons, is developed for the diagonalization of the collective quadrupole Hamiltonian for a system with an odd particle coupled to an anharmonic even core. Examples: the transition from prolate to oblate via #gamma#-unstable shapes and furthermore the hsub(9/2) spectra of the nuclei "1"8"7Ir and "1"9"7Tl. (Auth.).

International Nuclear Information System (INIS)

The essential difference as well as the apparent identity between the triaxial-rotor model and the gamma-vibrational model have been discussed. From the gamma decay mode, the [19/2"-]_1 states of the j = 11/2"- family in "1"8"7Ir and "1"8"9Ir have been identified as the K = j + 4 states, the presence of which contradicts the particle plus triaxial-rotor model. (author).

Energy Technology Data Exchange (ETDEWEB)

The reconstruction of steel lining of the FFTF reactor building is described. The cold part of the lining has a simple structure and represents a steel sheet of 6.35 mm thickness welded to I-shaped imbedded in concrete, the hot part is meant for resisting the hot sodium contacting with it. The reconstruction has been reduced to the substitution of usual lining, the sheets of which are fixed in such a way that dangerous strains in metal arising at evaporation are excluded by the new structure admitting sheet deformation.

Energy Technology Data Exchange (ETDEWEB)

The electrical resistivity at low temperatures (T = 10 to 90 K) of the lithium isotopes /sup 6/Li and /sup 7/Li and of an isotopic mixture /sup 7 +6/Li has been studied. The specimens contained a small amount of chemical impurities. An appreciable difference was observed in the temperature dependence of the resistivity produced both by deformation of the phonon spectrum, related to the change in isotopic composition, and by the presence of chemical impurities making the nonequilibrium part of the electron distribution function more isotropic.

International Nuclear Information System (INIS)

A series of Model Tests of Embedment Effect on Reactor Buildings has been carried out by the Nuclear Power Engineering Corporation (NUPEC), under the sponsorship of the Ministry of International Trade and Industry (MITI) of Japan. Seismic response of an embedded reactor building is greatly affected by the non-linearity of the backfill soil. However, quite few experimental data have been obtained so far. The objective of this study is to qualitatively evaluate the non-linear behavior of the backfill soil through shaking table tests. Its effects to the seismic response of a reactor building constructed at a soft rock site can be made clear through the tests. Non-linear effects of the backfill soil on the seismic response of the embedded reactor building model were evaluated experimentally. Based on the sinusoidal and seismic wave excitation tests, the following conclusions were obtained regarding the changes in vibrational characteristics of the building model which occurred according to ...

International Nuclear Information System (INIS)

The ductility of extruded heavy-section Ti-base--Mo--V--Fe--Al alloy was studied. Metallographic evidence for the large effect of grain size on ductility is presented. Fracture was found to occur in large-grain material after less deformation than in smaller grain size specimens.

Energy Technology Data Exchange (ETDEWEB)

In this paper, the adaptive optics (AO) system at Keck Observatory is characterized. The AO system is described in detail. The physical parameters of the lenslets, CCD and deformable mirror, the calibration procedures and the signal processing algorithms are explained. Results of sky performance tests are presented: the AO system is shown to deliver images with an average Strehl ratio of up to 0.37 at 1.59 {micro}m using a bright guide star. An error budget that is consistent with the observed image quality is presented.