British Library Electronic Table of Contents (United Kingdom)

Regularities of deformation-induced dissolution of a surface layer of iron oxides in matrixes of iron-based alloys with bcc and fcc lattices have been studied by the methods of M?ssbauer spectroscopy, transmission electron microscopy, and X-ray diffraction. A method of producing iron alloys strengthened by dispersed oxide nanoparticles and alloyed with elements possessing a high affinity to oxygen (titanium and yttrium) has been proposed, which implies a dynamic dissolution of a surface layer of iron oxides upon strong cold deformation and a precipitation of secondary yttrium and titanium nanooxides upon a subsequent high-temperature sintering of mechanically alloyed powders. There has been demonstrated a possibility of oxide strengthening of pure iron upon its interaction with air without...

British Library Electronic Table of Contents (United Kingdom)

Methods of X-ray diffraction and transmission electron microscopy were used to study the microstructure of dispersion-strengthened Cu-Al2O3 nanocomposites obtained by the method of simultaneous deposition of Cu and Al2O3 from the vapor phase. The effect of the size of particles of the oxide (Al2O3) and of their content on the electrical resistance of the composite has been considered. The results obtained make it possible to suppose that the main structural factor that determines the electrical resistance of the composite are nanodispersed particles of Al2O3 with a size of less than 20 nm.

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the modeling, dispersion, formation, transformation, monitoring and biological effects of atmospheric pollution. Specific topics include a prognostic mesoscale model for pollutant transport and diffusion, commuter exposure modeling, a Gaussian plume model for an urban area, carbon monoxide dispersion in an urbanized area, wind-tunnel modeling of flue gas dispersion, the regional-scale transport of fine aerosol components in eastern North America, and a Markov process for the generation of hourly average wind vectors. Attention is also given to photochemical aerosol formation in multicomponent systems, heterogeneous nitrogen oxide-particulate reactions, the generation and measurement of primary soot aerosols of size between 50 and 400 A, inertial particle size classification techniques, the design of air quality monitoring networks, visibilities in polluted and unpolluted areas, ...

Energy Technology Data Exchange (ETDEWEB)

This thesis is in the field of gas emission control from automobile and stationary sources. Out of the possible approaches to the elimination of pollutant gases, such as nitrogen oxides (NO{sub x}), one consists in the selective catalytic reduction (SCR) of these NO{sub x} on a suitable heterogeneous catalyst. Ammonia or hydrocarbons are employed as reducing agents. The most important catalysts active in the SCR of NO{sub x} are based on ions of transition metal either supported on several oxides or dispersed in zeolites. The catalysts have been characterized by electron magnetic resonance techniques (EPR, ENDOR, ESEEM) and the interaction of catalysts with nitrogen oxides, with reducing and poisoned agents have been followed with the same techniques. Copper dispersed on alumina and its interaction with both NO and ammonia has been investigated. Also the interaction between both ...

British Library Electronic Table of Contents (United Kingdom)

High purity W and W-0.9La2O3 (wt.%) nanopowders were produced by a wet chemical route. The precursor was prepared by the reaction of ammonium paratungstate (APT) with lanthanum salt in aqueous solutions. High resolution electron microscopy investigations revealed that the tungstate particles were coated with oxide precipitates. The precursor powder was reduced to tungsten metal with dispersed lanthanum oxide. Powders were consolidated by spark plasma sintering (SPS) at 1300 and 1400degreeC to suppress grain growth during sintering. The final grain size relates to the SPS conditions, i.e. temperature and heating rate, regardless of the starting powder particle size. Scanning electron microscopy revealed that oxide phases were mainly accumulated at grain boundaries while the tungsten matrix ...

British Library Electronic Table of Contents (United Kingdom)

Fluoroalkyl end-capped vinyltrimethoxysilane oligomer suffered the sol-gel reaction under alkaline conditions in the presence of titanium oxide nanoparticles in tetrahydrofuran to afford the corresponding fluorinated oligomer/titanium oxide nanocomposites[RF-(VM-SiO2)n-RF/TiO2] in excellent to moderate isolated yields. These fluorinated composites thus obtained were nanometer size-controlled fine particles, and exhibited good dispersibility and stability in traditional organic solvents except for water. These fluorinated nanocomposites were applied to the surface modification of glass to exhibit not only a completely superhydrophobic characteristic (a water contact angle: 180degree) with a non-wetting property against water droplets but also a good oleophobicity imparted by fluoroalkyl seg...

Energy Technology Data Exchange (ETDEWEB)

Limited field trial results of a heating oil additive package developed to minimize unscheduled maintenance indicate that it achieves its goal of keeping heating oil systems cleaner. The multifunctional additive package was developed to provide improved fuel oxidation stability, improved corrosion protection, and dispersency. This combination of performance benefits was chosen because we believed it would retard the formation of sludge, as well as allow sludge already present to be carried through the system without fouling the fuel system components (dispersency should keep sludge particles small so they pass through the filtering system). Since many unscheduled maintenance calls are linked to fouling of the fuel filtering system, the overall goal of this technology is to reduce these maintenance calls. Photographic evidence shows that the additive package not only reduces the amount of sludge formed, but even removes ...

Energy Technology Data Exchange (ETDEWEB)

It has been discovered that when Taiheiyo coal pulverized to 200 mesh or smaller is dispersed in naphthalene, a non-hydrogen-donor solvent, and reacted under hydrogen pressure in the presence of a red mud/sulfur catalyst, the catalyst exhibits activity in the regeneration of hydrogen donor solvents which have been hydrogen-depleted in the course of coal liquefaction. It is already known that inorganic matter contained in coal acts as a catalyst in liquefaction. This suggests that the reported effect of the red mud/sulfur catalyst is due to the iron oxide reacting with the sulfur and forming pyrrhotite. 22 refs., 6 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

A solid electrolytic capacitor having a solid electrolyte comprising manganese dioxide dispersed in an aromatic polyamide capable of further cure to form polyimide linkages, the solid electrolyte being disposed between a first electrode made of valve metal covered by an anodic oxide film and a second electrode opposite the first electrode. The electrolyte autogenously produces water, oxygen, and hydroxyl groups which act as healing substances and is not itself produced pyrolytically. Reduction of the manganese dioxide and the water molecules released by formation of imide linkages result in substantially improved self-healing of anodic dielectric layer defects.

Energy Technology Data Exchange (ETDEWEB)

In this work, the silicon oxynitride layer was studied as a tunneling layer for non-volatile memory application by fabricating low temperature polysilicon thin film transistors on glass. Silicon wafers were oxynitrided by only nitrous oxide plasma under different radio frequency powers and plasma treatment times. Plasma oxynitridation was performed in RF plasma using inductively coupled plasma chemical vapor deposition. The X-ray energy dispersive spectroscopy was employed to analyze the atomic concentration ratio of nitrogen/oxygen in oxynitride layer. The oxynitrided layer formed under radio frequency power of 150 W and substrate temperature of 623 K was found to contain the atomic concentration ratio of nitrogen/oxygen as high as 1.57. The advantage of high nitrogen concentration in silicon oxide layer formed by using nitrous oxide plasma was investigated by capacitance-voltage measurement. The ...

Energy Technology Data Exchange (ETDEWEB)

Investigations are discussed carried out in a pilot plant at the Kaz. Power Engineering Scientific Research Institute into the effect of the amount of primary air in coal-dust flame on the final concentration of nitrogen oxides in flue gases. The tests were carried out in a 7500 mm high, 1600 mm dia vertical cylindrical combustion chamber having type P-57 burner, and air dispersed fuel plus additional air supplies located at the top. Amounts of coal dust fed by a drum feeder along the air pipe varied from 100-600 kg/h. The required air was supplied by 5000 m/sup 3//h Type TK-700/5 blowers at 0.04 MPa. Ehkibastuz coal samples contained: 1.3% moisture; 48.1% ash; 38.02% carbon; 2.56% hydrogen; 0.73% sulfur; 0.60% nitrogen; heat of combustion was 14.3 MJ/kg. Results obtained indicate that variations in the amount of primary air in swirl flow burners affect formation of fuel nitrogen; there is an optimum volume at which minimum quantities of ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the characteristics of selected parameters of organic matter of the Tertiary coal samples and organic matter of Carboniferous rock samples from the Spitsbergen. The coal samples were taken from Central Coal Basin (the Longyearbyen region) and from the Forlandsundet Basin (Oscar II Land, the Kaffioyra region). Samples of dispersed organic matter were collected from Suffolk Pynten and Sergeijevfjellet area in Sorkapp Land. The optical properties of coal samples are different from properties of dispersed organic matter. Macerals of vitrinite group dominate in all of the samples. The average content of vitrinite group macerals is much lower in dipersed organic matter samples than it is in coals. The average content of liptinite group macerals is a little lower, and inertinite group macerals is much higher. The average content of mineral matter is higher in organic matter samples than in coal samples. The average value of ...

Energy Technology Data Exchange (ETDEWEB)

A brief review and assessment of field measurement programs that provide data for mixed layer diffusion research is presented. The majority of programs emphasize either the meteorological aspects of the mixed layer or plume characterization. Few programs are available that provide the complimentary blend of plume and appropriate meteorological measurements needed to adequately validate mixed layer diffusion theory. Three major U.S. EPA (Environmental Protection Agency) field programs that provide data bases for model development and validation of mixed layer diffusion processes are described and discussed in more detail. The Regional Air Pollution Study (RAPS) focused on measurements of surface and mixed layer turbulent transport processes in the urban environment. The Tennessee Plume Study (TPS) obtained a database with coincident measurement of boundary layer turbulent structure and plume dispersion for a large coal-fired power plant in nonuniform terrain over ...

International Nuclear Information System (INIS)

Nano-sized zinc oxide was synthesized and deposited onto cellulosic fibers using the sol-gel process at ambient temperature. The prepared materials were characterized using several techniques including scanning electron microscopy, transmission electron microscopy, diffuse reflectance spectroscopy, X-ray diffraction and thermogravimetric analysis. X-ray diffraction studies of the ZnO-coated fiber indicate formation of the hexagonal crystal phase which was satisfactory crystallized on the fiber surface. The electron micrographs show formation of zinc oxide nanoparticles within 10-15 nm in size which have been homogeneously dispersed on the fiber surface. The prepared materials show significant photocatalytic self-cleaning activity, which was monitored by diffuse reflectance spectroscopy. The photoactivity was studied upon measuring the photodegradation of methylene blue and eosin yellowish under UV-Vis irradiation. The ...

International Nuclear Information System (INIS)

For direct writing of electrically conducting connections and areas into insulating gold oxide thin films a scanning Ar"+ laser beam and a 30 keV Ga"+ focused ion beam (FIB) have been used. The gold oxide films are prepared by magnetron sputtering under argon/oxygen plasma. The patterning of larger areas (dimension 10-100 #mu#m) has been carried out with the laser beam by local heating of the selected area above the decomposition temperature of AuO_x(130-150 C). For smaller dimensions (100 nm to 10 #mu#m) the FIB irradiation could be used. With both complementary methods a reduction of the sheet resistance by 6-7 orders of magnitude has been achieved in the irradiated regions (e.g. with FIB irradiation from 1.5 x 10"7#OMEGA#/#square# to approximately 6 #OMEGA#/#square#). The energy-dispersive X-ray analysis (EDX) show a considerably reduced oxygen content in the irradiated areas, and scanning electron microscopy (SEM), as ...

Energy Technology Data Exchange (ETDEWEB)

Samarium cobaltite ceramic perovskites, with and without platinum particles dispersion, are possible candidates as electrode for electrochemical conversion of hydrocarbon and for intermediate temperature solid oxide fuel cells (ITSOFC). In this work, samarium cobaltites were synthesized by the combustion method using cobalt, and samarium nitrates as cation precursors and urea as fuel. For containing-platinum compositions Pt (II) acetyl acetonate was also employed as precursor. The effect of Sr on the phase formation and its electrical behavior is also studied. Specific surface area (BET), SEM-EDX, TEM and XRD analysis are used to characterize the powders obtained. Powders were pressed into pellets and sintered in air in the temperature range of 1200 -1400 C. Electrical impedance spectroscopy studies (EIS) are performed on sintered samples. The as-prepared powders showed an amorphous structure and by TEM a very small particle size ...

DEFF Research Database (Denmark)

Udgivelsesdato: DEC 1

Energy Technology Data Exchange (ETDEWEB)

The ball-milling method was used to produce Mg-50 wt.% ZrFe{sub 1.4}Cr{sub 0.6} composite. The thermodynamic, kinetic, and cycling properties, as well as the resistance to oxidation were examined. This composite possesses excellent kinetic properties, even at moderate temperature. Scanning electron microscopy, energy-dispersive spectrum, transmission electron microscopy and X-ray diffraction were used to characterize the composite before and after hydriding. The fine ZrFe{sub 1.4}Cr{sub 0.6} particles covering Mg particles acting as a ''catalytic film'', a significant amount of imperfections and some alloy powder in the Mg matrix introduced by ball milling all contributed to the enhanced absorption/desorption rate. (orig.)

International Nuclear Information System (INIS)

Nanodimensional powders of cubic copper ferrite are synthesized by two-steps procedure of co-precipitation of copper and iron hydroxide carbonates, followed by mechanochemical treatment. X-ray powder diffraction, Moessbauer spectroscopy and temperature-programmed reduction are used for the characterization of the obtained materials. Their catalytic behavior is tested in methanol decomposition to hydrogen and CO and total oxidation of toluene. Formation of nanosized ferrite material is registered even after one hour of milling time. It is established that the prolonging of treatment procedure decreases the dispersion of the obtained product with the appearance of Fe2O3. It is demonstrated that the catalytic behavior of the samples depends not only on their initial phase composition, but on the concomitant ferrite phase transformations by the influence of the reaction medium. -- Graphical abstract: It is demonstrated that the catalytic behavior ...

International Nuclear Information System (INIS)

A highly sensitive and stable tris(2,2'-bipyridyl)ruthenium(II) (Ru(bpy)_3 "2"+) electrogenerated chemiluminescence (ECL) sensor was developed based on carbon nanotube (CNT) dispersed in mesoporous composite films of sol-gel titania and perfluorosulfonated ionomer (Nafion). Single-wall (SWCNT) and multi-wall carbon nanotubes (MWCNT) can be easily dispersed in the titania-Nafion composite solution. The hydrophobic CNT in the titania-Nafion composite films coated on a glassy carbon electrode certainly increased the amount of Ru(bpy)_3 "2"+ immobilized in the ECL sensor by adsorption of Ru(bpy)_3 "2"+ onto CNT surface, the electrocatalytic activity towards the oxidation of hydrophobic analytes, and the electronic conductivity of the composite films. Therefore, the present ECL sensor based on the CNT-titania-Nafion showed improved ECL sensitivity for tripropylamine (TPA) compared to the ECL sensors based on both titania-Nafion ...

British Library Electronic Table of Contents (United Kingdom)

Dispersal can be regarded as a process operating both between and within patches of suitable habitat. For uncontrolled dispersal processes, the risk of crossing the borders of the habitat patch and arriving in the unsuitable landscape matrix will increase with decreasing patch area, in particular when the distance between isolated habitat patches is larger than the species' average dispersal capacity. Ballooning dispersal in spiders can be considered as a passive dispersal process, in which dispersed distances depend on the prevalent wind velocity. We executed a reaction norm analysis to analyze how dispersal propensity of the salt marsh wolf spider Pardosa purbeckensis depended on population characteristics (patch size) and the environment (wind velocity). Dispersal propensity was affecte...

Energy Technology Data Exchange (ETDEWEB)

Bremstrahlung Isochromat Spectroscopy (BIS). The XES spectra were collected using a Specs electron gun for the excitation and the XES 350 grating monochromator and channel plate system from Scienta as the photon detection. Spectra were collected in 'normal mode,' where the electron gun kinetic energy (KE) and the energy position of the center of the channel plate were both fixed and the energy distribution in the photon (hv) spectrum was derived from the intensities distributed across the channel plate detector in the energy dispersal direction. The polycrystalline Ce sample was oxidized by exposure to air at ambient pressures. After introduction to the ultra-high vacuum system, the oxidized sample was bombarded with Ar, to clean the topmost surface region and stabilize the surface and near surface regions. Although CeO{sub 2} would be the thermodynamically preferred composition in an oxygen rich ...

Energy Technology Data Exchange (ETDEWEB)

Nanocrystalline processing by inert gas condensation has the inherent advantages of generating: (1) high surface area nanoclusters, (2) non-stoichiometric oxides, and (3) high dispersions of dopants. This approach is exploited in the synthesis of fluorite-structured catalysts for SO{sub 2} reduction by CO. Nanocrystalline CeO{sub 2{minus}x}, La-doped CeO{sub 2{minus}x}, and Cu-doped CeO{sub 2{minus}x} were produced by magnetron sputtering from a pure or mixed metal target, followed by controlled oxidation of the metallic clusters. The as-prepared doped and undoped nanocrystalline CeO{sub 2{minus}x} materials were found to be excellent catalysts for complete SO{sub 2} conversion to elemental sulfur. Undoped nanocrystalline CeO{sub 2{minus}x} enabled light-off at 460 C, a temperature {approximately} 120 C lower than that over polycrystalline CeO{sub 2}, which is a novel effective catalyst itself. The high catalytic activity ...

Science.gov (United States)

Five hydrated inorganic divalent cations, Mg[sup 2+], Co[sup 2+], Ni[sup 2+], Cu[sup 2+], and Zn[sup 2+], have successfully been used as templates for the synthesis of manganese oxide octahedral molecular sieves (OMS-1) having the todorokite structure. The OMS-1 samples have been well characterized by X-ray diffraction, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy/energy dispersive X-ray studies, inductively coupled plasma analysis, electron paramagnetic resonance, Fourier transform infrared spectroscopy, thiosulfate titration, and cyclohexane sorption. Catalytic CO oxidation and 2-propanol decomposition were carried out. Results show that these OMS-1 samples with a tunnel size of about 6.9 angstroms are crystalline and chemically pure. They have the following formulas: Mg[sub 3.17]Mn[sub 5.05]O[sub 12] [center dot] 4.52H[sub 2]O, Co[sub 1.84]Mn[sub 5.59]O[sub 12] [center dot] ...

Energy Technology Data Exchange (ETDEWEB)

Ceria (CeO{sub 2})-modified PtRu/C catalysts with different compositions of Ru and CeO{sub 2}, viz. PtRu{sub 0.9}(CeO{sub 2}){sub 0.1}/C, PtRu{sub 0.7}(CeO{sub 2}){sub 0.3}/C and PtRu{sub 0.5}(CeO{sub 2}){sub 0.5}/C and unmodified PtRu/C catalyst were synthesized by the sodium borohydride reduction method. Transmission electron microscopic results indicated that the lower concentrated CeO{sub 2}-modified PtRu/C catalysts had almost a similar morphological structure (well-dispersed particles with size around 2.3-2.5nm) with that of the unmodified PtRu/C catalyst. X-ray diffraction and X-ray photoelectron spectroscopy analyses indicated the formation of PtRu alloy and presence of CeO{sub 2} in an amorphous form with a mixed oxidation states (Ce{sup 3+}-Ce{sup 4+}). Electro-catalytic activity of these catalysts for methanol oxidation was investigated by linear sweep voltammetry and chronoamperometry and it was found that the ...

International Nuclear Information System (INIS)

A series of silylated Co/SBA-15 catalysts were prepared via the reaction of surface Si-OH of SBA-15 with hexamethyldisilazane (HMDS) under anhydrous, vapor-phase conditions, and then characterized by FT-IR, N2 physisorption, TG, XRD, and TPR-MS. The results showed that organic modification led to a silylated SBA-15 surface composed of stable hydrophobic Si-(CH3)3 species even after calcinations and H2 reduction at 673 K. Furthermore, the hydrophobic surface strongly influenced both metal dispersion and reducibility. Compared with non-silylated Co/SBA, Co/S-SBA (impregnation after silylation) showed a high activity, due to the better cobalt reducibility on the hydrophobic support. However, S-Co/SBA (silylation after impregnation) had the lowest FT activity among all the catalysts, due to the lower cobalt reducibility along with the steric hindrance of grafted -Si(CH3)3 for the re-adsorption of ?-olefins. -- Graphical abstract: The silylation of an SBA-15 before ...

Energy Technology Data Exchange (ETDEWEB)

A hydrogen peroxide injection system was designed and installed in the stack of a 5,274 million J/hr industrial pilot plant scale combustion chamber using natural gas as fuel. The concentration of peroxide in the gas stream was precisely controlled by continuous injection using an electromagnetic dosage pump, the liquid 50% peroxide solution was finely dispersed into the gases by a water cooled custom designed delivery system with a spray nozzle at the tip. Residence times between 0.1 and 1.8 seconds and concentrations of H{sub 2}O{sub 2} between 280 ppm and 4,000 ppm were used during the test runs. CEMS for total hydrocarbons, carbon monoxide, nitrogen oxides, as well as an ultrasonic gas flow monitor were used to measure the effect of hydrogen peroxide in reducing the emissions of these pollutants. Destruction removal efficiencies between 25% and 100% were observed for hydrocarbons, and concentrations of CO, as well as NO{sub x}. were reduced ...

International Nuclear Information System (INIS)

High resolution Monte-Carlo simulations show that the neutron spectrum, fuel burnup and fuel temperature feedback effect of a PWR core loaded with Thoria-based fuel (Th/Pu-O_2) do not significantly differ from the MOX fuelled one due to the similar neutronic characteristics of both fertile materials (Th-232, U-238). The core physics of this fuel variant is characterized by an enhanced moderator/void temperature coefficient (by factor 2.4) and high incineration rate for Pu (approx. 60 %). A PWR core loaded with the Molybdenum-based inert matrix fuel (IMF) - in contrast to MOX-, shows a harder spectrum, resulting in small temperature coefficients of reactivity and particularly in a higher fuel depletion rate as well as an enhanced TRU reduction performance. The incineration of Pu amounts to 46 % resulting, in turn, in generation of minor actinides of about 10 % of the total Pu consumption. The higher excess reactivity resulting from the initial Pu contents is controlled by the use of ...

Science.gov (United States)

Two major modes of CO adsorption on SiO{sub 2}-supported Pd reflect different extents of back-donation, which is, at least in part, controlled by the local electron density at the adsorption site. The fraction of CO in the bridging mode (B) increases and that of the linear mode (L) decreases, with increasing size of the Pd particles, indicating high electron density at Pd atoms in terraces of close-packed crystal faces, in agreement with Smoluchowski's classical model. For samples reduced at 300{degree}C our data points and those of other authors are located on a common curve of B/L vs metal dispersion. Extensive reduction at 600{degree}C results in significantly lower B/L values, attributed to the incipient formation of a palladium silicide. Oxidation followed by reduction at 300{degree}C destroys the silicide, and the B/L value returns to the original curve.

International Nuclear Information System (INIS)

Cyclic voltammetry (CV), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) were employed to investigate the electrodeposition of Eu and Al in an LiCl-KCl eutectic melt containing Eu2+ and Al3+ at 450 deg. C. In order to deposit a pure Eu and Al alloy, the stoichiometrically lower concentration of Al3+ than that of Eu2+ and Al wires as a counter electrode was introduced into the bath of LiCl-KCl melt for the electrodeposition. The electrodeposition takes place at a potential more negative than -1.95 V vs. Ag|Ag+ while the deposit is oxidized at more positive potential than -1.92 V. Two new reduction peaks and an anodic peak on a W working electrode were observed at -2.39 V, -2.42 V, and -2.1 V, vs. Ag|Ag+, respectively, suggesting that the potential window of the Al system in LiCl-KCl melt can be extended to -2.43 V vs. Ag|Ag+. The EDS analysis indicated that AlEu can be deposited at the potential more negative than ...

Wastenet

...of Mixing Sections 9 Interacting Rotor/Stator Mixers 10 Floating Ring Mixing Devices 11 Static (or Motionless) Mixers 12 Incorporation of Liquid Additives and Dispersions by Direct Addition 13 Dispersive Mixing of Fillers and Pigments 14 Dispersive Mixing Applied to Polymer Blending 15 Compounding with Single Screw Extruders Appendix - Preparation of Microtome Sections for Assessment of Dispersive In order to get a feel for this book, you can view Chapter 1 now, simply follow the link ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The radiation dose and the atmospheric dispersion for Pressurized Heavy Water Reactors (PHWR) are based on the CAN/CSA N288.2-M91 standards: for Pressurized Water Reactor (PWR) on the NRC Regulatory Guide 1.145. There are some differences between in the methodologies used in the standards, including the atmospheric dispersion model, the release height, the temperature lapse rate, the cutoff condition. This paper reports on a comparison of standards for atmospheric dispersion models of PHWRs and PWRs in order to determine which one is the more conservative. The comparison between PHWR and PWR for atmospheric dispersion factors and radiation doses confirms that there are no big differences

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Effects of the addition of precious metals (PM; Pt, Rh) on CeO{sub 2}/Al{sub 2}O{sub 3} and CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} were confirmed to enhance the oxygen storage capacities (OSC). Increments in the OSC of the added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} catalysts were much greater than those in the OSC of the PM added CeO{sub 2}/Al{sub 2}O{sub 3}. The enhanced OSC is ascribed to the interaction between PM and a CeO{sub 2}-La{sub 2}O{sub 3} solid solution formed during the catalyst preparation. No enhancements in the OSC were observed on physical mixing of CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3} and Pt-Rh/Al{sub 2}O{sub 3}, although the composition ratio of PM:CeO{sub 2}:La{sub 2}O{sub 3} is the same as that in the PM added CeO{sub 2}/La{sub 2}O{sub 3}/Al{sub 2}O{sub 3}. This indicates that the intimate contacts between the precious metals and CeO{sub 2} particles dispersed on Al{sub 2}O{sub 3} are essential for the enhanced OSC ...

International Nuclear Information System (INIS)

SiC-AlN and SiC-SiAlON refractory composites were obtained by means of nitridation of the mixtures of silicon carbide (SiC) powder with a broad granulometric distribution and powders of aluminium (Al) and aluminium-silicon (Al-Si) mixtures. The mixtures of the composition Al-25% Si, Al-50% Si and Al-75% Si were previously prepared by means of 'mechanical alloying' technique. Thermodynamic analysis was accomplished in order to evaluate the viability of SiC-SiAlON and SiC-AlN refractories production by the chosen processing method, and the results confirmed viability of such. Investigation of nitridation of Al and Al-Si powder compacts in order to obtain the AlN and #beta#-SiAlON matrix phases of the composite was accomplished by means of differential thermal analysis (DTA) and thermogravimetric analysis (TG). The results of the thermal analysis show that nitridation of the Al-25% Si, Al-50% Si and Al-75% Si resulting in p-SiAlON formation occur at temperatures of 910 deg C, 811 deg C ...

International Nuclear Information System (INIS)

... ammonium compounds benzilic acid chemical preparation lanthanum oxides

UK PubMed Central (United Kingdom)

The safety, pharmacokinetics, and distribution in tissue of an amphotericin B (AmB)-cholesteryl sulfate colloidal dispersion (ABCD) were compared with those of micellar amphotericin B-deoxycholate (m-AmB)....Full Text Available

UK PubMed Central (United Kingdom)

Species that depend on ephemeral habitat often evolve distinct dispersal strategies in which the propensity to disperse is closely integrated with a suite of morphological, behavioural and physiological...Full Text Available

UK PubMed Central (United Kingdom)

Pigment-dispersing factor (PDF) is a neuropeptide that plays a prominent role in the circadian clock of several insects. The cockroach Leucophaea maderae...Full Text Available

Science.gov (United States)

Gun barrel vibrations lead to dispersion in the shot patterns. Thus, reducing these vibrations should lead to increased accuracy. Since the muzzle is the anti-node for all vibration modes and its vibrations have the greatest effect on shot dispersion, it ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

British Library Electronic Table of Contents (United Kingdom)

This paper is devoted to investigate the influences of thermal dispersion and magnetic field on a hot semi-infinite vertical porous plate embedded in a saturated Darcy-Forchheimer-Brinkman porous medium. The coefficient of thermal diffusivity has been assumed to be the sum of the molecular diffusivity and the dynamic diffusivity due to mechanical dispersion. The effects of transverse magnetic field parameter (Hartmann number Ha), Reynolds number Re (different velocities), Prandtl number Pr (different types of fluids) and dispersion parameter on the wall shear stress and the heat transfer rate are discussed.

Science.gov (United States)

Dispersants have been widely used as a primary response measure for marine oil spills around the world. Recently, the U.S. Environmental Protection Agency (EPA) developed an improved laboratory dispersant testing protocol, called the Baffled Flask Test (BFT). The BFT protocol w...

Energy Technology Data Exchange (ETDEWEB)

The propagation of acoustic pressure perturbations in an adiabatic low-quality air/water flow were investigated both theoretically and experimentally. A linearized dispersion model is correlated with data to extract information on the behavior of interfacial momentum transfer controlled by the virtual volume coefficient. The dispersion model is examined in limiting cases of low and high frequency and related to current models for critical flow velocity. Fourier decomposition techniques are employed to predict the dispersion of measured pressure pulses and to relate data for standing waves and propagating pulses. The dispersion model is based on a two-fluid model and is the most complete model available in the literature at this time. The dispersion data presented herein is also the best available to date for low frequency (i.e., frequencies less than bubble resonance) sound ...

British Library Electronic Table of Contents (United Kingdom)

Seed dispersal involves several complex stages that can be affected by multiple peripheral processes. Thus, a major dispersal event can be followed by secondary dispersal, which can reduce density-dependent mortality and consolidate the dispersal phase. But predation events can also follow, and predation of seeds in feces is particularly interesting because it can heavily alter the fate of seeds dispersed through vertebrate guts. Our review of 20 cases involving this kind of interaction found that research has chiefly been in tropical and subtropical areas (85% of cases), suggesting that it is a minor phenomenon at higher latitudes. However, the small size of both the seeds and predators involved may have caused this process to go unnoticed outside the tropics. We tested the presence of pr...

Energy Technology Data Exchange (ETDEWEB)

A hydrous oxide film for the application as dielectric film is synthesized by immersion of pure aluminum in hot water. From a Rutherford backscattering analysis, the ratio of aluminum to oxygen atoms was found to be 3:2 in the anodized aluminum oxide film, and 2:1 in the hydrous oxide layer. Anodization of the hydrous oxide layer was more effective for the transition of amorphous anodic oxides to the crystalline aluminum oxides.

Science.gov (United States)

Basic research of the structure and electronic properties of a-Si:H is reported with particular emphasis on the role of defects. The main findings are as follows: (1) low defect density material can be deposited at a high rate using SiH/sub 4/ diluted in He or Ne. Using Ar or Kr results in a high defect density and columnar material; (2) an electrical bias during deposition modifies the band gap, hydrogen concentration and structure; (3) the clustering of hydrogen in the regions between the columns is confirmed; (4) hydrogen diffusion is observed by NMR; (5) the oxidation of an a-Si:H surface results in approx. 3 x 10/sup 11/ cm/sup -2/ dangling bonds at the interface; (6) auger recombination of photoexcited carriers is a significant non-radiative mechanism at low temperatures; (7) non-radiative recombination by diffusion and capture at dangling bonds is observed at temperatures above 50 to 100/sup 0/K; (8) the defect density in doped and compensated a-Si:H is ...

Energy Technology Data Exchange (ETDEWEB)

Ni catalysts supported on {gamma}-Al{sub 2}O{sub 3}, CeO{sub 2} and CeO{sub 2}-Al{sub 2}O{sub 3} systems were tested for catalytic CO{sub 2} reforming of methane into synthesis gas. Ni/CeO{sub 2}-Al{sub 2}O{sub 3} catalysts showed much better catalytic performance than either CeO{sub 2}- or {gamma}-Al{sub 2}O{sub 3}-supported Ni catalysts. CeO{sub 2} as a support for Ni catalysts produced a strong metal-support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO{sub 2} had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/{gamma}-Al{sub 2}O{sub 3} catalysts for this reaction. A weight loading of 1-5wt% CeO{sub 2} was found to be the optimum. Ni catalysts with CeO{sub 2} promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO{sub 2}-promoted ...

International Nuclear Information System (INIS)

Particulate ceramic composites that were composed of a combustion-synthesized #beta#'-SiAlON matrix and dispersed MoSi_2 particles were hot pressed at 1,600 C in a nitrogen atmosphere. The physical and mechanical properties of the composites that contained 15, 30, and 45 vol% MoSi_2 were evaluated. The average four-point bend strength, fracture toughness, and Vickers hardness of the composites were in the ranges of 500--600 MPa, 3--4 MPa#centre dot#m"1"/"2, and 11--13 GPa, respectively. The measured mechanical strength and hardness were very similar to the values that were predicted from the rule of mixtures. The fracture toughness of the combustion-synthesized #beta#'-SiAlON (2.5 MPa#centre dot#m"1"/"2) was apparently enhanced by the MoSi_2 particles that were added. The increase in the fracture toughness was predominantly attributed to the residual thermal stress that was induced by the thermal expansion mismatch between the MoSi_2 particles and the ...

International Nuclear Information System (INIS)

We have investigated the growth behaviors of high temperature compatible ZrO_2 insulation coatings on Ag and AgMg sheathed Bi_2Sr_2Ca_1Cu_2O_x superconducting tapes depending on number of dipping and thermal conditions. The coatings were fabricated on long-length superconducting tape substrates using a solution derived from Zr tetrabutoxide, solvent and chelating agent for high magnetic field magnets. The layer-on-layer growth behaviors were characterized by environmental scanning electron microscope (ESEM), energy dispersive spectroscopy (EDS), X-ray maps and X-ray diffraction (XRD). This research showed that the ZrO_2 coatings were regularly grown on Ag-based tape substrates and coating thickness increased with increasing number of dipping. It was found that ceramic oxides formed at temperature range 450 and 550 deg. C. The final coating thickness changed between 6 and 8 #mu#m after annealing process. Resistance of insulation measured from ...

International Nuclear Information System (INIS)

The World Bank is analyzing the role of economic policy instruments for the control of air pollution in Poland, in cooperation with Polish and international experts. The first stage, covering Poland as a whole, was recently completed, jointly financed with the U.S. E.P.A. and the Government of the Netherlands. The second stage, now under way, will extend the analysis into a specific regional framework. Stage 2 is financed by the World Bank, the Polish Government, and the U.K. Environment Know-How Fund. Air Pollution in Poland is overwhelmingly caused by energy production and uses, due to the fact that the Polish economy depends heavily on coal and lignite. At present, vehicles contribute less to total emissions than do coal burning and industrial processes, although they account for 25-35% of nitrogen oxides, carbon monoxide, hydrocarbons and lead; and the concentrated in areas of high population density. The paper shows how economic, technical and meteorological ...

Energy Technology Data Exchange (ETDEWEB)

A new type of zinc electrode is matched with new bifunctional air electrodes to produce a zinc-air battery of a novel design. The zinc electrode is a flow-thru type made from copper foam-metal. The air electrode uses corrosion resistant carbon black as a high area support for a highly dispersed spinel oxide electrocatalyst. The battery design employs flowing electrolyte, 12 M KOH saturated or supersaturated with zincate. Single cells as large as 200 cm{sup 2} (1/5 EV design scale) having a capacity of 20 AH have been tested with C/4--C/16 constant current cycling. More extensive and realistic life cycle testing was done with 2 Ah cells, including the Simplified Federal Urban Driving Schedule (SFUDS) cycle. This testing has confirmed that these cells can provide the necessary transient power response required for urban EV applications. The cells achieved an average of 72 SFUDS repetitions (7.2 hrs) per discharge cycle, more than twice the number ...

UK PubMed Central (United Kingdom)

The oxidative stress theory of aging predicts that manipulations that alter oxidative stress/damage will alter aging. The gold standard for determining whether aging is altered is lifespan,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Short communication.

International Nuclear Information System (INIS)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

... Accession Number : ADD257320. Title : Sputter Deposition of Yttrium-Oxides. Descriptive Note : Journal article,. Corporate ...

Energy Technology Data Exchange (ETDEWEB)

Chemical oxidation is a treatment technology that uses powertul chemical oxidizers to destroy organic contaminants. Typical oxidizers used in chemical oxidation processes include ozone, hydrogen peroxide, chlorine, and potassium permanganate. The chemical reaction products are usually simple organic compounds, such as carboxylic acids, and/or inorganic compounds, such as carbon dioxide, water, and simple inorganic complexes (e.g., chloride salts, in the case of chemical oxidation treatment of chlorinated solvents).

International Nuclear Information System (INIS)

A variable-dispersion electron spectrometer is being installed for use by the Stanford Superconducting Accelerator in conjunction with its Free Electron Laser program. The system has been designed to operate with electron beam energies from 20 MeV to 200 MeV, with a maximum energy resolution of 0.01% FWHM. The maximum energy acceptance is approximately #+-# 5%, as determined by the bending magnet aperture. Resolution is controlled by adjusting the focal conditions at the entrance to a 90 degree bending magnet, while the dispersion is controlled by changing the magnitude and polarity of the field in a quadrupole magnet which immediately follows the bending magnet. 4 refs., 5 figs.

Energy Technology Data Exchange (ETDEWEB)

This paper presents the results of a series of experiments performed to study the effect of initial pressure vessel conditions on the extent of melt dispersal from scaled reactor cavities and describes progress in development of a mathematical model which is designed to predict the melt mass dispersed from reactor cavities as a function of reactor vessel initial conditions and on the vessel breach area. The model, which is being developed to also characterize the heat transfer and chemical reaction phenomena which would take place within the reactor cavity, is designed to be incorporated into a lumped-parameter containment analysis computer code.

Energy Technology Data Exchange (ETDEWEB)

It is demonstrated that highly dispersed molybdenum sulfide catalysts are prepared by using Mo(CO){sub 6} adsorbed on the support. The structure of ultradispersed molybdenum sulfide is suggested by EXAFS techniques to be different from that of MoS{sub 2}. The TOF of the thiophene HDS is almost invariant with the dispersion of molybdenum sulfide at a high molybdenum dispersion, whereas the TOF of the hydrogenation greatly increases with increasing dispersion. On the basis of the HDS activity and optimum Co/Mo ratio of Co-Mo/Al{sub 2}O{sub 3} catalysts having a variety of molybdenum dispersion fabricated by using carbonyl complexes, it is demonstrated that highly active HDS catalysts are prepared by highly dispersing molybdenum sulfide phases. Edge decorations of molybdenum sulfides by cobalt are suggested for the synergy generation between cobalt and molybdenum ...

British Library Electronic Table of Contents (United Kingdom)

Abstract A one step method was used to prepare stable aqueous nanocomposite dispersions based on cellulose whiskers extracted from the rachis of the date palm tree and a poly(styrene co 2 ethyl hexylacrylate) copolymer via miniemulsion polymerization. A reactive silane, i.e., methacryloxypropyl triethoxysilane was added to stabilize the dispersion and favor the anchoring of the whiskers on polymer particles. Dynamic light scattering was used to study the effect of the silane and whiskers contents on the average particle size of the polymer. Nanocomposites materials were prepared from these dispersions using a casting/evaporation method. The effect of the silane and whiskers contents on the thermal and mechanical properties were studied using differential scanning calorimetry and dynamic me...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

British Library Electronic Table of Contents (United Kingdom)

Oxidation of propylene with oxygen, air and a mixture of nitrogen?oxygen in a barrier discharge is investigated. The selectivity towards formation of propylene oxide in pure oxygen is shown to be as high as 45 wt% and the propylene conversion ratio is found to be 12.9 wt%. In the oxidation with air, the propylene oxide selectivity is 23 wt%, while the conversion is 7.5 wt%. The values of propylene conversion and selectivity towards formation of propylene oxide in a barrier discharge are consistent with those obtained by the thermocatalytic methods for production of propylene oxide.

Energy Technology Data Exchange (ETDEWEB)

Production of cermet nuclear fuel having fine uranium dioxide (UO{sub 2}) particles dispersed in matrix metal requires basic property data on the compatibility of matrix metal with fission product compounds. It is thermodynamically suggested that, as burnup increases, cesium in oxide fuel reacts with the fuel, other fission products or cladding pipe and produces cesium uranates, cesium molybdate, or cesium chromate in stainless steel cladding pipe. Attempt was made to measure the thermal expansion coefficient and thermal conductivity of cesium uranates (Cs{sub 2}UO{sub 4} and Cs{sub 2}U{sub 2}O{sub 7}), cesium molybdate (Cs{sub 2}MoO{sub 4}) and cesium chromate (Cs{sub 2}CrO{sub 4}). Thermal expansion was measured by X-ray diffraction and determined by Cohen`s method. Thermal conductivity was obtained by measuring thermal diffusion by laser flash method. The thermal expansion of Cs{sub 2}UO{sub 4} and Cs{sub 2}U{sub 2}O{sub 7} is as low as 1.2% ...

Science.gov (United States)

A mathematical model describing the behavior of a gas of any density released into a turbulent atmosphere was developed. A numerical treatment was established for two dimensional flow. An understanding of the effects of accidental or continuous release wa...

Energy Technology Data Exchange (ETDEWEB)

The biodegradation of one of the most commonly used commercially available dispersants in the treatment of hydrocarbon out-flow was studied. The culture mediums employed were sea water, sterile sea water, and medium M19 (Merck). The latter two were inoculated with two kinds of microorganisms of the Pseudomona genus isolated from sludge from a waste treatment plant. The dispersants used is a commercial product made of anionic sulphated dispersants (1.710% by weight); anionic sulphonated dispersants (0.144%) and non-ionic dispersants (8.146%), both accompained by hidrocarbonated solvent (90%). The degradation processes occurred at differents temperatures (20, 30 and 37). The greatest degradation was obtained at 30 degree centigree. The degradation percentages obtained with the miscroorganisms were 40% of the anionic total and 70% of the non-ionic total after 56 hours for the 5:2 ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the mechanism of the oxidation and ammoxidation of propylene was made. The products of the above reactions were acrylonitrile and acrolein for ammoxidation and oxidation, respectively. Also, the ammoxidation and oxidation of allyl alcohol, allyl amine, and their allylic deuterium substituted analogues was studied. It was concluded that oxidation and ammoxidation of propylene have the same rate determining step. Other conclusions about the reaction intermediates were also made.

Energy Technology Data Exchange (ETDEWEB)

Three dispersants (stearic acid, oleic acid, and poly-(12-hydroxystearic acid)) are compared for their ability to produce low-viscosity suspensions of zirconia in kerosene. Rheological measurements and sediment packing density measurements show that poly(12-hydroxystearic acid) is a better dispersant than stearic acid or oleic acid; this is explained in terms of the longer tail of the poly-(12-hydroxystearic acid) surfactant molecule. The amount of dispersant can be optimized to reduce viscosity and yield point of the suspension, and to eliminate thixotropic hysteresis. The use of a dispersion medium of lower viscosity than the dispersant makes it easy to detect when complete monolayer coverage has been achieved. The loss of pseudoplasticity, brought about by a higher degree of deflocculation, can be recovered by increasing the volume fraction of solids of a suspension and this is ...

Energy Technology Data Exchange (ETDEWEB)

Finite-difference acoustic-wave modeling and reverse-time depth migration based on the full wave equation are general approaches that can take into account arbitrary variations in velocity and density and can handle turning waves as well. However, conventional finite-difference methods for solving the acoustic- or elastic-wave equation suffer from numerical dispersion when too few samples per wavelength are used. The flux-corrected transport (FCT) algorithm, adapted from hydrodynamics, reduces the numerical dispersion in finite-difference wavefield continuation. The flux-correction procedure endeavors to incorporate diffusion into the wavefield continuation process only where needed to suppress the numerical dispersion. Incorporating the flux-correction procedure in conventional finite-difference modeling or reverse-time migration can provide finite-difference solutions with no numerical dispersion even ...

UK PubMed Central (United Kingdom)

Background. The Free Radical Theory of Aging mechanistically links oxidative stress to aging. Okinawa has among the world's longest-lived populations but oxidative stress in this...Full Text Available

UK PubMed Central (United Kingdom)

1. Nitric oxide generation is important in the regulation of resistance vessel tone. Until now, however, there has been no evidence of such a role for basal generation of nitric oxide in the skin microcirculation...Full Text Available

UK PubMed Central (United Kingdom)

Studies were conducted to quantitate the evolution of nitrogen oxides (NO_(x)) from soybean [Glycine max (L.) Merr.] leaves during in vivo nitrate reductase...Full Text Available

UK PubMed Central (United Kingdom)

The potential for oxidation of ammonia in anoxic marine sediments exists through anaerobic oxidation by Nitrosomonas-like organisms, utilizing nitrogen dioxide, coupling of nitrification,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

Science.gov (United States)

The growth of an oxide interfacial layer was recently found to increase the open-circuit voltage (OCV) and efficiency by up to 60 per cent in GaAs metal-semiconductor solar cells. Details of oxidation techniques to provide the necessary oxide thickness and chemical structure and using ozone, water-vapor-saturated oxygen, or oxygen gas discharges are described, as well as apparent crystallographic orientation effects. Preliminary results of the oxide chemistry obtained from X-ray, photoelectron spectroscopy are given. Ratios of arsenic oxide to gallium oxide of unity or less seem to be preferable. Samples with the highest OVC predominantly have As(+3) in the arsenic oxide rather than As(+5). A major difficulty at this time is a reduction in OCV by 100-200 mV when the antireflection coating is vacuum deposited.

UK PubMed Central (United Kingdom)

PurposeCataracts are often considered to be an unavoidable consequence of aging. Oxidative damage is a major cause or consequence of cortical and nuclear cataracts, the most common...Full Text Available

Science.gov (United States)

Metastable yttrium-oxide films are synthesized using reactive sputter deposition. The yttrium concentration of the as-deposited film is found to vary as a function of the sputter deposition rate. In addition to the synthesis of the cubic equilibrium phase...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a catalyst composition. It consists of the catalytic oxides of iron, bismuth, molybdenum and magnesium as essential components and optionally the oxides of cobalt, nickel, phosphorus and arsenic.

Science.gov (United States)

May 31, 2011 ... A Theoretical Solid Oxide Fuel Cell Model for System Controls and Stability Design AUTHOR(S): Kopasakis, George; Brinson, Thomas; Credle, ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Incomplete dispersion of aggregates is a well known difficulty when analyzing soil texture of Andosols, particularly if no fresh soil material is available. To facilitate such investigations, several dispersion procedures were carried out on air dried samples rich in short range order minerals, originating from selected Andosol profiles (S Mexico). As a result, we propose an improved method based on a sequential chemical treatment with K oxalate, NH4 oxalate, and oxalic acid that reliably removes cementing agents and allows for a stable dispersion of soil particles after addition of Na pyrophosphate. This method was proved to be well reproducible and highly reliable for routine grain size determinations. The potential error caused by the inherent risk of dissolving primary mineral...

British Library Electronic Table of Contents (United Kingdom)

Abstract Smoke is a mixture of toxic gases and suspended particulate matter of solids and liquids that evolves from a fire of flammable materials. This article presents real-time consequence modeling to track the concentration of individual species in smoke as well as its soot deposition. In the modeling process presented, the burning rate or vapor mass is fed into a combustion model in which the combustion of products has been identified and quantified along with the temperature of the fire. The output of the combustion model is the smoke that will be dispersed into the ambient. The fire geometry, which depends on the type of fire (e.g., pool or flare), is identified. A dispersion model with the capability of determining particulate deposition is then used for tracking the smoke plume. Th...

Energy Technology Data Exchange (ETDEWEB)

A wavelength division multiplexer/demultiplexer having optical path lengths between a fiber array and a Fourier transform lens, and between a dispersion grating and the lens equal to the focal length of the lens. The optical path lengths reduce losses due to angular acceptance mismatch in the multiplexer. Close orientation of the fiber array about the optical axis and the use of a holographic dispersion grating reduces other losses in the system. Multi-exposure holographic dispersion gratings enable the multiplexer/demultiplexer for extremely broad-band simultaneous transmission and reflection operation. Individual Bragg plane sets recorded in the grating are dedicated to and operate efficiently on discrete wavelength ranges.

International Nuclear Information System (INIS)

A stable chlorobenzene dispersion of conducting polyaniline (PANI) has been obtained by doping emeraldine base with dodecylbenzene sulfonic acid (DBSA) and studied by spectrophotometric measurements in the UV-vis-IR range. The electrical properties of PANI: DBSA films obtained from the above dispersion have been investigated under different temperature and relative humidity conditions. All-organic chemoresistive devices have been developed by spin-coating the PANI: DBSA dispersion on flexible substrates, and then by depositing electrodes on the top, from a carbon nanotube conducting ink. Sensing tests performed under exposition to calibrated amounts of ammonia reveal that these simple and inexpensive sensors are able to detect ammonia at room temperature in a reliable way, with a sensitivity linearly related to concentration in the range between 5 ppm and 70 ppm.

International Nuclear Information System (INIS)

Dispersed flow film boiling is the heat transfer regime that occurs at high void fractions in a heated channel. The way this transfer mode is modelled in the NRC computer codes (RELAP5 and TRAC) and the validity of the assumption and empirical correlations used is discussed. An extensive review of the theoretical and experimental work related with heat transfer to highly dispersed mixtures reveals the basic deficiencies of these models: the investigation refers mostly to the typical conditions of low rate bottom reflooding, since the simulation of this physical situation by the computer codes has often showed poor results. The alternative models that are available in the literature are reviewed, and their merits and limits are highlighted. The modification that could improve the physics of the models implemented in the codes are identified. (author) 13 figs., 123 refs.

CERN Document Server

We investigate the chemical and observational implications of repetitive transient dense core formation in molecular clouds. We allow a transient density fluctuation to form and disperse over a period of 1 Myr, tracing its chemical evolution. We then allow the same gas immediately to undergo further such formation and dispersion cycles. The chemistry of the dense gas in subsequent cycles is similar to that of the first, and a limit cycle is reached quickly (2 - 3 cycles). Enhancement of hydrocarbon abundances during a specific period of evolution is the strongest indicator of previous dynamical history. The molecular content of the diffuse background gas in the molecular cloud is expected to be strongly enhanced by the core formation and dispersion process. Such enhancement may remain for as long as 0.5 Myr. The frequency of repetitive core formation should strongly determine the level of background molecular enhancement. ...

British Library Electronic Table of Contents (United Kingdom)

Industrial effects have long been significant factors in wage inequality. Previous research indicates that wage differentials across industries were increasing through the mid 1980s. Using more recent data, however, we find that the level of inter-industry wage dispersion declined by 36% from 1986 to 2002 despite the continued trend towards increasing inequality in the labor force. This decline in inter-industry wage dispersion is evident across gender and educational groups. Using multilevel growth curve models, our multivariate results indicate that the decline is only weakly related to industrial changes in education, occupation or even productivity despite the fact that the latter variable had been a critical factor in the prior period. Indicators of globalization and downsizing also d...

International Nuclear Information System (INIS)

Deep level effects in GaAs MOSFET have been characterised in the ohmic channel using DLTS, low frequency excess noise and dispersion technique. An isothermal multi exponential curve fitting method has been devised and implanted into the DLTS system. Multi exponential curve fitting method used to decompose a multi exponential transient into its constituents so that the peak signature can be better characterised for the case whereas several peaks are closely spaced. Low frequency excess noise and dispersion techniques also confirm the trap in signature of the same traps observed in the DLTS measurements. (author)

British Library Electronic Table of Contents (United Kingdom)

A ferritic steel with finely dispersed precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersed TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Short communication.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The influence of MeV electrons irradiation on the gate oxide layers of hydrogenated polysilicon thin film transistors (TFTs) was investigated by measuring gate leakage currents and threshold voltages. The experimental data revealed a decrease of oxide trap density and increase of positive oxide charge. Improvement in the interface roughness and in the oxide quality near the bottom interface was observed.

KoreaScience (Korea)

Full Text Available

J-STORE (Japan)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The RKR potential energy curves are constructed for the ground states of diatomic hafnium oxide and thorium oxide. Using Lippincott and Hulburt-Hirschfelder potential function the dissociation energies are estimated by curve fitting method. The H-H potential function was found to give a better fit in both cases. The dissociation energies of hafnium oxide and thorium oxide are estimated as 9.04 #+-# 0.02 eV and 10.34 #+-# 0.01 eV respectively. (author).

Science.gov (United States)

PMID:11506019

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

Energy Technology Data Exchange (ETDEWEB)

Targets for heterogeneous transmutation of americium are composed of a support material, the inert matrix and of an americium oxide compound: AmO{sub 2-x} or Am{sub 2}O{sub 3}. In parallel to the studies using americium, simulated compounds of americium oxide, chosen amongst lanthanide oxides, are used. The selection of these compounds is based on theoretical, physical and crystallochemical considerations. In order to assess the influence of impurities composed of lanthanide oxides, resulting from the separation process, on the physical and chemical properties of such a target, synthesis of oxide powders containing impurities associated with the simulated americium oxide, characterizations, crystallographic studies and sodium compatibility tests have been performed. (author)

British Library Electronic Table of Contents (United Kingdom)

Desulphurization of gasoline and kerosene was carried out using organic and inorganic oxidants. Among the organic oxidants used were hydrogen peroxide in combination with acetic acid, formic acid, benzoic acid and butyric acid, while inorganic oxidants used included potassium permanganate and sodium perchlorate. The oxidation of each petroleum oil was carried out in two steps; the first step consisted of oxidation of the feed at moderate temperature and atmospheric pressure while in the second step, the oxidized mixture was extracted with azeotropic mixture of acetonitrile-water. A maximum desulphurization has occurred with NaClO4 and hydrogen peroxide and acetic acid, which are 68% and 61%, respectively in case of gasoline and 66% and 63%, respectively in case of kerosene oil. The FTIR st...

Energy Technology Data Exchange (ETDEWEB)

A kinetic model based on the Mars-van Krevelen mechanism that allows to describe the microkinetics of the heterogeneously catalysed partial oxidation of {alpha}, {beta}-unsaturated aldehydes is presented. This conversion is represented by a network, composed of the oxidation of the {alpha}, {beta}-unsaturated aldehyde towards the {alpha}, {beta}-unsaturated carboxylic acid and the consecutive oxidation of the acid as well as the parallel reaction of the aldehyde to products of deeper oxidation. The reaction steps of aldehyde respectively acid oxidation and catalyst reoxidation have been investigated separately in transient experiments. The combination of steady state and transient experiments has led to an improved understanding of the interaction of the catalyst with the aldehyde and the carboxylic acids as well as to a support of the kinetic model assumptions. (orig.)

International Nuclear Information System (INIS)

English Oct 1996 p. 352-353 Brazil Maliska, Ana Maria Kuehn, Ingeborg Klein,

Energy Technology Data Exchange (ETDEWEB)

A stochastic-convective reactive (SCR) transport method is developed for one-dimensional steady transport in physically heterogeneous media with nonlinear degradation. The method is free of perturbation amplitude limitations and circumvents the difficulty of scale dependence of phenomenological parameters by avoiding volume-averaged specifications of diffusive/dispersive fluxes. The transport system is conceptualized as an ensemble of independent convective-reactive streamlines, each characterized by a randomized convective velocity (or travel time). Dispersive effects are treated as a component of the randomness in the streamline velocity ensemble, so no explicit expression for hydrodynamic dispersive flux is written in the streamline transport equation. The expected value of the transport over the stream tube ensemble is obtained as an average of solutions to the reactive convection equation according to the stream tube ...

UK PubMed Central (United Kingdom)

The analysis of individual molecules is evolving into an important tool for biological research, and presents conceptually new ways of approaching experimental design strategies. However, more...Full Text Available

UK PubMed Central (United Kingdom)

ObjectivesIn old age, there are marked changes in both the structure of the liver sinusoidal endothelial cell and liver perfusion. The objective of this study was...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The Sunshine Project of Japan was inaugurated in 1974. Since 1980 it has been promoting priority projects such as coal liquefaction. Japan is now promoting the basic and applied research that underpins this development and is increasing the efficiency of technical development. With regard to risk dispersion, the expansion of international cooperation such as the IEA is being promoted.

Energy Technology Data Exchange (ETDEWEB)

The oxidative dehydrodimerization of propylene to C/sub 3/-dimers (1,5-hexadiene and benzene) has been examined at 600/sup 0/C and atmospheric pressure using a (Bi/sub 2/O/sub 3/)/sub 0.85/(La/sub 2/O/sub 3/)/sub 0.15/ oxide ion-conducting catalyst in a reactor where a catalyst disk separates a feed of propylene in helium from air. The surface of the disk exposed to propylene was reoxidized not by gaseous O/sub 2/, but by the dissociative adsorption and reduction of dioxygen at the oxidant side of the disk, followed by oxide ion conduction to replace spent lattice oxygen. Selectivity to C/sub 3/-dimers when using lattice oxide migration to reoxidize the catalyst was considerably greater than when O/sub 2/ was added to the propylene feed under the same reaction conditions. This result supports the proposal that lattice oxygen is predominantly involved in the selective ...

International Nuclear Information System (INIS)

The magnon dispersion curve of Gd metal has been determined from first principles by use of augmented-plane-wave energy bands and wave functions. The exchange matrix elements I (k,k') between the 4f electrons and the conduction electrons from the first six energy bands were calculated under the assumption of an unscreened Coulomb interaction. The results are in good overall agreement with experiment provided the I (k,k') are diminished by a constant scale factor of about 2 which may be caused by screening.

Energy Technology Data Exchange (ETDEWEB)

The purpose of SEADEX was to acquire a comprehensive, high-quality data base for evaluating models of dispersion within coastal zones, it secondary objective was to provide data to help determine which meteorological measurements are most appropriate for emergency preparedness at nuclear power plant sites. The study was conducted in the vicinity of Kewannee, Wisconsin, on the western shore of Lake Michigan. This report describes the design of the study and the data base resulting from it. Both a gas tracer (SF/sub 6/) and a particulate tracer (oil fog) were used. (ACR)

International Nuclear Information System (INIS)

A dispersion interferometer based on CO2 laser for measurements of plasma line density in the gas dynamic trap (GDT) experiment has been developed with sensitivity el>min ? 1.1013 cm-2, temporal resolution ?50 ns. The main advantages of the interferometer are compactness and low sensitivity to vibrations. The interferometer does not require specific vibration isolation structure and can be mounted directly on the working chamber of the plasma device. The above mentioned advantages have been successfully demonstrated in the Gas Dynamic Trap experiments.

International Nuclear Information System (INIS)

The procedure of charge-coupled devices (CCD) are investigated by using MOS capacitors for enhancing their ionizing radiation tolerance. Authors have found that the gate oxidation temperature, thickness of SiO_2 gate insulator and high temperature processes after gate oxidation are crucial for determining the radiation tolerance of the devices, and proposed to decrease the thickness of gate insulator, perform gate oxidation at 1000 deg C by means of dry oxidation and minimize the number of high temperature procedure steps after gate oxidation. All stated above is a necessary preparation for priducing radiation hardened charge-coupled devices.

Energy Technology Data Exchange (ETDEWEB)

Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window ...

British Library Electronic Table of Contents (United Kingdom)

Zirconium and particularly Zr-2.5wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate. In this study, we demonstrate a two step pro...

Energy Technology Data Exchange (ETDEWEB)

Trichloroethene (TCE), a common groundwater contaminant, can be degraded under certain conditions by microorganisms that occur naturally in the subsurface. TCE can be degraded under anaerobic conditions to less chlorinated compounds and ultimately into the non-chlorinated, non-hazardous end product, ethene, via anaerobic reductive dechlorination (ARD). ARD is widely recognized as a TCE degradation mechanism, and occurs in active groundwater remediation and can occur during monitored natural attenuation (MNA). MNA relies on natural processes, such as dispersion and degradation, to reduce contaminant concentrations to acceptable levels without active human intervention other than monitoring. TCE can also be biodegraded under aerobic conditions via cometabolism, in which microbial enzymes produced for other purposes fortuitously also react with TCE. In cometabolism, TCE is oxidized directly to non-hazardous products. Cometabolism as a ...

International Nuclear Information System (INIS)

The formation of thin SiO_2 layers on silicon and metal silicides was studied by phase- and thickness measurements with Rutherford back-scattering of 2 MeV alfa particles. Thermal oxidation was done in steam and dry oxygen at temperatures between 750 degrees Celsius and 1 100 degrees Celsius, while SiO_2 formation at room temperature was carried out by anodic oxidation. The study of silicon oxidation was done on Si<100>, Si<111> and amorphous silicon substrates. Thermal oxidation of CoSi_2, CrSi_2, NiSi_2, PtSi and TiSi_2 was investigated. The oxidation rates of the silicides were found to be much higher than for silicon. The oxidation process is also diffusion-limited with a higher oxidation rate for steam as compared to dry oxygen. The silicide layers were found to stay intact during thermal oxidation. A ...

Energy Technology Data Exchange (ETDEWEB)

MCrAlY coatings are widely used on hot section components of gas turbines to provide hot corrosion and/or oxidation protection by formation of an oxide layer on the surface. As the protective oxide scale exfoliates during service, aluminum from the coating diffuses outward for reformation of the protective scale. Aluminum may also diffuse inward due to the differences in composition between the coating and the substrate. Thus, the coatings degrade due to oxidation, oxide scale spallation, and inward and outward diffusion of aluminum. Service life of these coatings is controlled by the aluminum content in the coating, operating temperature and start- shutdown cycles. In-service degradation of CoCrAlY and CoNiCrAlY coatings is presented. A procedure to predict the remaining service life of coatings under oxidizing conditions is discussed. (orig.) 12 refs.

Science.gov (United States)

... Accession Number : ADD141533. Title : Yttrium Oxides in Vacuum-Plasma- Sprayed CoNiCrAlY Coatings,. Descriptive Note : Journal Article,. ...

Wastenet

Emissions and residues: Emissions may include, inter alia, nitrogen oxides, carbon monoxide, sulphur dioxide and other oxides

UK PubMed Central (United Kingdom)

Reactive oxygen species (ROS), inevitable byproducts of aerobic metabolism, are known to cause oxidative damage to cells and molecules. This, in turn, is widely accepted as a pivotal determinant of...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The influence of surface oxides of variable composition and nonstoichiometry formed at high temperatures in air on the general corrosion resistance of ferritic chromium steel type 08H17T (Fe-17Cr-1Ti) in weak sulfuric acid has been studied. Anodic passive films formed on steel with different pretreatments have also been examined. The surface oxide of nearly stoichiometric composition formed at 300 C provides for the passive state of steel in sulfuric acid despite its depletion by chromium when compared with that for nonstoichiometric Cr-enriched oxide formed at 600 C. The dissolution and transformation of nonstoichiometric thermal surface oxide in sulfuric acid appear to take place through defect sites, {minus}Fe{sup 2+} ions, and oxygen vacancies of the n-type conductor. The passive film formed on the nonstoichiometric oxide film, which had been produced at 600 C, was found to be ...

Science.gov (United States)

... ADD137758. Title : The Oxidation Behavior of CoCrAlY, CoCrAl and Yttrium-Implanted CoCrAl Alloys Compared and Contrasted,. ...

Energy Technology Data Exchange (ETDEWEB)

A catalytic process for the oxidation of sulfur-containing gases , E.G., sulfur dioxide and simultaneous production of sulfuric acid wherein a sulfur-containing gas is reacted with an oxygencontaining gas in the presence of a catalyst comprising an iron group metal on a solid support comprising a zeolite in a silicaalumina matrix.

UK PubMed Central (United Kingdom)

The gelation kinetics of an in situ gelable hydrogel formulated from oxidized dextran (Odex) and N-carboxyethyl chitosan (CEC) were investigated rheologically. Both Schiff base...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Rheological properties of moderately concentrated solutions of cellulose in methylmorpholine N-oxide-dimethylformamide mixtures containing hydrophilic montmorillonite nanoparticles were studied. Film composite materials were prepared, and their physicomechanical properties and structural organization were studied.

UK PubMed Central (United Kingdom)

We report the use of cysteine-substituted mutants in conjunction with in situ oxidation to determine the physical proximity of a pair of engineered cysteines in the pore region of the voltage-gated...Full Text Available

UK PubMed Central (United Kingdom)

A multidisciplinary approach was used to study the effects of pollution from a marine fish farm on nitrification rates and on the community structure of ammonia-oxidizing bacteria in the underlying...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The OH-initiated photo-oxidation of n-butane was used as a source of 1- and 2-butoxy radicals. Reactions producing ketones and other organic compounds are explained. Rates of photolysis were determined and are discussed.

UK PubMed Central (United Kingdom)

Oxidative stress has been implicated in the etiology of age-related muscle loss (sarcopenia). However, the underlying mechanisms by which oxidative stress contributes to sarcopenia have not been thoroughly...Full Text Available

UK PubMed Central (United Kingdom)

Neurons in the hippocampal CA1 region are particularly sensitive to oxidative stress (OS), whereas those in CA3 are resistant. To uncover mechanisms for selective CA1 vulnerability to OS, we...Full Text Available

UK PubMed Central (United Kingdom)

Quantitative probing of heterogeneous regions in muscle is feasible with phosphorus-31 magnetic resonance spectroscopy because of the differentiation of metabolic patterns of glycolytic and oxidative...Full Text Available

UK PubMed Central (United Kingdom)

Bacterial nitric oxide synthases (bNOS) are present in many Gram-positive species and have been demonstrated to synthesize NO from arginine in vitro and in vivo. However, the physiological role...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The oxidation conditions were investigated for obtaining a higher productivity in the production of high strength carbon fiber from polyacrylonitrile (PAN). The effect of incorporation of 2 % comonomer such as methyl acrylate (MA), acrylate containing carboxylate (SA), acrylamide (AAm), and hydroxyethyl acrylate (HEA) on the oxidation conditions was also investigated. The measurement of DSC and bonded oxygen content revealed that the most effective comonomer for promoting the cyclization of nitril group and the bonding of oxygen was found to be SA, and the second best was AAm. The measurement of tensile strength of carbon fiber showed that the copolymer of SA, HEA, and MA gave a high strength fiber. It took a long time to oxidize the carbon fiber when it was oxidized at a temperature on which double layer structure was not formed. To shorten the production time, a method of combining the upper limit ...

UK PubMed Central (United Kingdom)

Systemic administration of lipopolysaccharide (LPS), which causes endotoxemia and systemic inflammation, has been reported to induce expression of the gene for type II inducible nitric oxide synthase...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behavior of lanthanide oxides in molten alkaline chloride media is of great concern in pyrochemical processes for advanced nuclear fuel cycle. We have studied the solubilities of various lanthanide oxides in LiCl-KCl eutectic melt. In general, lanthanide oxides appeared to be insoluble/sparingly soluble in LiCl-KCl eutectic at 723 K. However, europium oxide exhibited an abnormal behavior in solubility and redox chemistry. The solubility of europium oxide was measured to be 1-2 order of magnitude higher than those of other lanthanide oxides. This abnormal solubility may be attributable to different electrochemical behavior of europium in the same experimental conditions. Most lanthanides ion exists as trivalent oxidation states. However, we observed divalent europium dissolved in LiCl-KCl molten salt by applying electron ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a method comprising applying a passivation layer of CaF{sub 2} to the surface of a superconductive ceramic oxide by evaporation. The CaF{sub 2} layer is effective to passivate the oxide surface without disrupting the superconductive properties.

UK PubMed Central (United Kingdom)

There is increasing evidence of a biochemical link between lipid oxidation and bone metabolism. Paraoxonase 1 (PON1) prevents the oxidation of low-density lipoprotein (LDL) and metabolizes biologically...Full Text Available

UK PubMed Central (United Kingdom)

Anionic peroxidase from tomato (Lycopersicon esculentum) fruit oxidized indoleacetic acid (IAA) slowly in the presence of Mn²⁺ and dichlorophenol in acetate buffers. The...Full Text Available

UK PubMed Central (United Kingdom)

Evolution of nitrogen oxides (NO_(x), primarily as nitric oxide) from soybean (Glycine max [L.] Merr.) leaves during purged in vivo nitrate reductase assays...Full Text Available

Science.gov (United States)

A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-

Energy Technology Data Exchange (ETDEWEB)

This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Partial oxidation of 2-propanol was carried out on AB{sub 1-x}B`{sub x}O{sub 3} (A=Ba, B=Pb, Ce, Ti; B`=Bi, Sb and Cu) type perovskite oxides. Acetone was the major product observed on all the catalysts. All the catalysts underwent partial reduction during the reaction depending on the composition of the reactant, nature of the B site cation and the extent of substitution at B site. The catalytic activity has been correlated with the reducibility of the perovskite oxides determined from Temperature Programmed Reduction (TPR) studies. (orig.)

International Nuclear Information System (INIS)

... compilation fission products j codes mixed oxide fuels neutron reactions

Science.gov (United States)

... Title : Effect of Yttrium on the Microstructure of Titanium Alloys,. ... The yttrium was added in the melting stage as an oxide or in the elemental form. ...

International Nuclear Information System (INIS)

(1978). United States Quan, B. Becker, M. Harris, DR Rensselaer Polytechnic

Energy Technology Data Exchange (ETDEWEB)

Measurements were completed on the solubility of cupric and cuprous oxides in liquid water and steam at controlled pH conditions from 25 to 400 C (77 to 752 F). The results of this study have been combined with those reported from this laboratory in two previous EPRI reports to provide a complete description of the solubility of these oxides and the speciation of copper dissolved in liquid water and steam as a function of oxidation state, temperature, pH, and in the case of steam, pressure. These constitute the first set of reliable data for cuprous oxide solubility over this range of conditions. For the more intensively studied CuO case, agreement was found between our results and those of previous studies of its solubility in steam, whereas only partial agreement was evident for its solubility in liquid water. For both oxides this disagreement often amounted to orders of ...

Science.gov (United States)

Thermal wet oxidations of GaP and Al{sub 0.4}Ga{sub 0.6}P at 650 degree sign C for various times have been performed. Comparisons are made on oxidation rates and post oxidation morphology. Transmission electron microscopy shows that when oxidizing GaP, polycrystalline monoclinic GaPO{sub 4}{center_dot}2H{sub 2}O forms without noticeable loss of phosphorus. Oxidation for 6 h or more leads to poor morphology resulting in cracks and detachment. A thickness expansion of about 2.5-3 times is noticed as a result of oxidation. In contrast, oxidized Al{sub 0.4}Ga{sub 0.6}P exhibits much better morphology without cracks or detachment from the substrate. The oxide has an almost amorphous-like microstructure. The oxidation process shows typical diffusion-limited reaction at long anneals. Preliminary work on the ...

International Nuclear Information System (INIS)

The behaviour of an elastomeric seal for vehicle brake Tandem master cylinder is measured and analyzed in temperature and brake fluids changed. Working conditions are simulated for different piston rod velocity and cylinder supply pressure, in temperature rising, brakefluid boundary and Nanoaluminum oxide brakefluid oxide brakefluid lubrication. The result shows that Nanoaluminum oxide brakefluid with its ball shape can highly reduce friction coefficient to avoid seal excessive wear and reduce slick slip in brake applications.

UK PubMed Central (United Kingdom)

A two-step purification protocol was used in an attempt to separate the constitutive NAD(P)H-nitrate reductase [NAD(P)H-NR, pH 6.5; EC 1.6.6.2] activity from the nitric oxide and nitrogen dioxide (NO_(x))...Full Text Available

International Nuclear Information System (INIS)

The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.

Energy Technology Data Exchange (ETDEWEB)

Oxide catalysis plays a central role in hydrocarbon processing and improvements in catalytic activity or selectivity are of great technological importance because these improvements will translate directly into more efficient utilization of hydrocarbon supplies and lower energy consumption in separation processes. An understanding of the relationships between surface structure and catalytic properties is needed to describe and improve oxide catalysts. Our approach has been to prepare supported oxides that have a specific structure and oxidation state and then employ these structures in reaction studies. Our current research program is focused on studying the fundamental relationships between structure and reactivity for two important reactions that are present in many oxide-catalyzed processes, partial oxidation and carbon-carbon bond formation. ...

Energy Technology Data Exchange (ETDEWEB)

The dispersion of more than 20 vol pct submicrometer ceramic particles within a metallic matrix and the deposition of such a cermet to form a thick and tough coating presents problems. Most of the coating techniques have failed in attempting to homogeneously disperse very fine and hard particles in large amounts while avoiding their decomposition or reaction with the metal matrix during the deposition process. A simple and efficient method has been developed for producing ceramic-containing composite coatings. It consists in synthesizing cermet-based materials and in depositing them by a rapid solidification process, such as thermal spraying. Boride- and carbide-based materials have been successfully obtained by plasma spraying reactive powders comprising the basic reagents. These materials, with a microstructure of submicrometer ceramic particles dispersed in a metallic matrix, exhibit good wear-resistant properties ...

International Nuclear Information System (INIS)

Central velocity dispersions and rotation curves to radii of approx.5 kpc have been measured for 32 galaxies, mostly field S0's. Our rotation curves confirm the result of Kormendy and Illingworth that the bulges of S0 galaxies are in rapid rotation, with enough rotational kinetic energy to account for their flattenings. The V/sigma-ellipticity relation we find for S0 bulges is compared with similar data for elliptical galaxies from Davies et al. We conclude that (1) faint SO bluges and elliptical galaxies (M/sub B/ fainter than -20.5) are both consistent with oblate rotators with isotropic velocity dispersions (although in our sample, S0 bluges are flatter, on the average, than ellipticals) and (2) bright S0 bulges, -22.0

CERN Document Server

Gravitational lensing by the dual cusp catastrophes of the cold dark matter (CDM) caustic rings at cosmological distances may provide the tantalizing opportunity to detect CDM indirectly, and discriminate between axions and weakly interacting massive particles (WIMPs). Caustics are places where the CDM particles are naturally focussed. Our focus is upon the caustic rings which are closed tubes whose cross-section is an elliptic umbilic catastrophe with three dual cusps. A caustic ring has a specific density profile, a specific geometry and, therefore, precisely calculable gravitational lensing signatures. The magnification monotonically increases as the line of sight approaches to the cusps where it diverges in the limit of zero velocity dispersion. In this limit, we find 37% magnification at a sample point near the outer cusps of the CDM caustic rings at cosmological distances. In the presence of finite velocity dispersion, the lower and upper ...

Energy Technology Data Exchange (ETDEWEB)

Capacitance dispersion on the fractal carbon electrode with edge and basal orientations was investigated using atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), and a.c.-impedance spectroscopy. For this purpose, four types of as-received pyrolytic graphite electrode, as-received, mechanically polished, and as-activated glassy carbon electrodes were prepared with different surface irregularities and amounts of edge orientations. The apparent self-similar fractal dimensions of the carbon electrodes were determined from the analyses of AFM images based upon triangulation method. The amounts of edge orientations on the surface of the carbon electrodes were qualitatively estimated from the XPS analysis of surface acidic functional groups that were preferably formed on the edge planes by the heat treatment of the carbon electrodes. The values of the constant phase element exponent {alpha} determined from the apparent self-similar fractal dimensions ...

Energy Technology Data Exchange (ETDEWEB)

With the increased usage of dispersion models that require stack top wind information, such as the Complex Terrain Dispersion Model (CTDM), the need for a reliable method to collect elevated wind data has also increased. Doppler Sound Detection and Ranging (SODAR) instruments have gained recognition as a viable means of collecting such data. SODAR technology has improved greatly over the last decade and is now a cost effective alternative to tall meteorological towers. SODARs are remote sensing devices that sample the atmosphere and calculate wind speed and wind direction data at different altitudes. This is accomplished by measuring the doppler shift of an acoustic pulse emitted by a ground level antenna.

International Nuclear Information System (INIS)

Published density profiles and central velocity dispersions place important constraints on the stellar velocity ellipsoid and on the distribution of dark matter (DM) in the dwarf spheroidal galaxies Draco and Ursa Minor. Central velocity dispersions of 9 km/s are adopted for Draco and 11 km/s for Ursa Minor. Then, for an isotropic stellar velocity distribution, the central DM densities are 0.8 and 1.0 solar mass/cu pc, respectively, if visible and dark matter have the same core radius. If DM has a much larger core radius than visible matter but nevertheless dominates the potential, these densities are reduced by a factor of 2. Central DM densities can be lower than this only if the stellar velocity distribution is anisotropic. Simple two-component King models are used to investigate this and to look for the smallest DM densities that are consistent with the observations. 36 refs.

International Nuclear Information System (INIS)

In this paper, a time-domain equivalent circuit method is applied to solve dispersion of coupled-cavity travelling-wave tube (CCTWT). First, the time-domain circuit equations of CCTWT coupled-cavity chain are deduced from the equivalent circuit model. Then, the equations are solved numerically by fourth-order Runge-Kutta method and a program CTTDCP is developed using MATLAB. Last, a L-band CCTWT is calculated using CTTDCP and the cavity pass-band of this tube is computed to be 1.08-1.48 GHz, which is consistent with the experimental results and the simulation results of electromagnetic code and demonstrates the validity of the time-domain equivalent circuit method. In addition, a new design method which uses the equivalent circuit method and electromagnetic simulation together to optimize the cold cavity characteristics of CCTWT is proposed. (authors)

British Library Electronic Table of Contents (United Kingdom)

Novel fluoroalkyl end-capped vinyltrimethoxysilane oligomeric nanoparticles were prepared by the hydrolysis of the corresponding oligomer under alkaline conditions. The size of fluorinated nanoparticles thus obtained is of submicrometer levels and is not sensitive to the refractive indices of a variety of solvents; however, the turbidity of the dispersed fluorinated nanoparticles is extremely sensitive to the refractive indices of these solvents. In particular, the solvents of which the refractive indices are from 1.378 to 1.408 were found to afford the transparent colorless dispersed particle solutions. More interestingly, the modified glass surface treated with fluorinated nanoparticles exhibited a completely superhydrophobic characteristic (a water contact angle: 180?) with a nonwetting...

CERN Document Server

TRANSVERSE EMITTANCE PRESERVATION IS A MAJOR CONCERN OF THE LHC INJECTOR CHAIN. MINIMISATION OF THE BLOW-UP DUE TO MISMATCH AT INJECTION INTO THE SPS IS THEREFORE MANDATORY. WHILE THE TRANSVERSE POSITIONN OF THE BEAM IN THE SPS INJECTION LINE IS MONITORED BUNCH BY BUNCH BY AN OTR (OPTICAL TRANSITION RADIATION) SCREEN AND A FAST CCD (CHARGED COUPLED DEVICE) CAMERA, THE PHASE SPACE MATCHING AT INJECTION IS MONITORED BY AN OTR BASED MISMATCH MONITOR IN THE SPS RING. ORTHOGONAL TUNING KNOBS WERE DEVELOPED TO TUNE INDEPENDENTLY TWISS PARAMETERS, DISPERSION AND DISPERSION DERIVATIVE. IN THIS PAPER WE DESCRIBE THE MISMATCH CORRECTION MECHANISM AS WELL AS THE TWO MONITORING SYSTEMS. WE REPORT ON FIRST MEASUREMENTS WHICH WERE CARRIED OUT DURING THE 1998 SPS RUN.

British Library Electronic Table of Contents (United Kingdom)

Microreserves may be useful in protecting native arthropod diversity in urbanized landscapes. However, species that do not disperse through the urban matrix may eventually be lost from these fragments. Population extinctions may be precipitated by an increase in genetic differentiation among fragments and loss of genetic diversity within fragments, and these effects should become stronger with time. We analyzed population genetic structure in the dispersal limited Jerusalem cricket Stenopelmatus n. sp. ?santa monica?? in the Santa Monica Mountains and Simi Hills north of Los Angeles, California (CA), to determine the impacts of fragmentation over the past 70 years. MtDNA divergence was greater among urban fragments than within contiguous habitat and was positively correlated with fragment ...

Energy Technology Data Exchange (ETDEWEB)

Laboratory {open_quotes}jar{close_quotes} tests compared eleven different fuel oil and diesel fuel sludge-control additives. Factors studied included (1) ability to disperse and prevent buildup of sludge deposits on surfaces, (2) ability to protect steel from corrosion, (3) ability to inhibit growth and proliferation of bacteria, and (4) ability to disperse water. Results varied greatly, and it was found that many commercial products do not do what they claim. It is concluded that fuel retailers should not believe manufacturers` claims for their additive products, but rather should test such products themselves to be sure that the benefits of treatment are real. A simplified form of the procedure used here is proposed as one way for dealers to do such testing.

International Nuclear Information System (INIS)

Heat-transfer augmentation by straight grid spacers in rod bundles is studied for single-phase flow and for post-critical heat flux dispersed flow. The heat transfer effect of swirling grid spacers in single-phase flow is also examined. Governing heat-transfer mechanisms are analyzed, and predictive formulations are established. For single-phase flow, the local heat transfer at a straight spacer and at its upstream or downstream locations are treated separately. The effect of local velocity increasing near swirling spacer is considered. For post critical heat flux (CHF) dispersed flow, the heat transfer by thermal radiation, fin cooling, and vapor convection near the spacer are calculated. The predictions are compared with experimental data with satisfactory agreement.

Energy Technology Data Exchange (ETDEWEB)

A new fuel-cell electrocatalyst based on highly porous carbonized polyacrylonitrile (PAN) microcellular foam with platinum particles was prepared recently in this laboratory. Its surface morphology, one of the most important aspects of a practical electrocatalyst, has been examined in terms of fractal theory and methods. The fractal dimension of the platinum particles dispersed in porous carbonized PAN foam was determined by using chronometric and rotating-disk-electrode methods in oxygen-saturated solutions. A fractal dimension smaller than 2 was obtained, which was attributed to the partially active nature of the surface of this electrocatalytic material. This value of fractal dimension is also proposed to be considered as a reaction dimension. A reaction dimension smaller than 2 may indicate that not all of the platinum particle surface is accessible to the incoming oxygen molecules.

International Nuclear Information System (INIS)

Stellar rotation velocities and velocity dispersions have been measured along the major and minor axes of NGC 4594 with the Canada-France-Hawaii Telescope. The observations show the kinematic signature of a nuclear disk of stars superposed on the bulge (Fig. 1). Apart from its larger size, this is similar to the nucleus of M31. It rotates rapidly: the apparent rotation curve reaches an inner maximum of V 231 #+-# 7 km s"-"1 at r = 5.''0. The apparent velocity dispersion falls from #sigma# = 250 #+-# 7 km s"-"1 at the center to 181 #+-# 6 km s"-"1 at r = 3.''7. (author).

Science.gov (United States)

Rapid administration of stable iodine is essential for the saturation and subsequent protection of the thyroid gland against the potential harm caused by radioiodines. This paper proposes the Dutch risk analysis that uses an atmospheric dispersion model to calculate the size of the zones around nuclear power plants where radiological thyroid doses for children might be sufficiently high to warrant iodine administration. Dose calculations for possible releases from the nuclear power plants of Borssele (The Netherlands), Doel (Belgium) and Emsland (Germany) are based on two scenarios in combination with a 1-y set of authentic, high-resolution meteorological data. The dimensions of the circular zones were defined for each nuclear power plant. In these zones, with a radius up to 50 km, distribution of stable iodine tablets is advised. PMID:20332130

Energy Technology Data Exchange (ETDEWEB)

In this project, graphite is used as a substitute for lead in order to maintain the machinability of plumbing components at the level of leaded brass. Graphite dispersed in Cu alloy was observed to impart good machinability and reduce the sizes of chips during machining of plumbing components in a manner similar to lead. Copper alloys containing dispersed graphite particles could be successfully cast in several plumbing fixtures which exhibited acceptable corrosion rate, solderability, platability, and pressure tightness. The power consumption for machining of composites was also lower than that of the matrix alloy. In addition, centrifugally cast copper alloy cylinders containing graphite particles were successfully made. These cylinders can therefore be used for bearing applications, as substitutes for lead-containing copper alloys. The results indicate that copper graphite alloys developed under this DOE project have a great potential to ...

CERN Document Server

A prism spectrometer has been developed to operate in the VUV wavelength range from 120 to 200 nm. It can be used as a pre- disperser in conjunction with a Fabry-Perot based gas refractometer. This instrument has also been used to measure the refractive index of the liquid radiator C/sub 6/F/sub 14/ in various spectral lines. This radiator is used in the RICH detectors of the DELPHI experiment and has been proposed for ALICE, and LHCb experiments. The spectral resolution of the system is improved as the wavelength decreases and the data are consistent with a wavelength accuracy about 0.4 nm at 140 nm. The results for the dispersion curve of the above liquid are presented. (17 refs).

British Library Electronic Table of Contents (United Kingdom)

Coordination of CoCl2 solutions to the silica polyamine composite, WP-1, made with the branched polymer polyethylenimine (PEI) shows irreversible binding resulting from surface oxidation of the Co2+-Co3+. This is not the case for the silica polyamine composite BP-1 made with the linear polymer polyallylamine where reversible binding and no oxidation is observed. These observations suggested that oxidation of the cobalt was related to the greater coordination number available with the branched polyamine relative to the linear polyamine. A study of the kinetics of cobalt binding to WP-1 indicated initial loading of Co2+ at relatively low coordination number followed by desorption of Co2+ leading to oxidation and irreversible binding. Exclusion of oxygen from the composite-cobalt solution mix...

International Nuclear Information System (INIS)

#beta#-sialon ceramics of equal overall compositions but containing amorphous, partly crystalline and almost completely crystalline intergranular phase(s) have been oxidized in oxygen at 1350 deg C for 20 hours. The obtained weight gain curves do not follow the parabolic rate law (#DELTA#W/A_0)"2= k_pt + #beta#. To the extent that crystallization occurs in the oxide scale during the oxidation experiment, the amorphous cross section area through which oxygen most easily diffuses will decrease with time. A brief description of this new rate law is given, and the obtained oxidation curves will be discussed within that framework. 4 refs., 2 tabs., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

One-electron oxidation of several derivatives of pyrazolin-5-one, including the drug antipyrine, were studied by pulse radiolysis of aqueous solutions. All the compounds were found to be oxidized by Br2 rapidly but considerably more slowly by weaker oxidants, such as peroxyl radicals. From redox equilibria using p-methoxyphenol and N,N,N',N'-tetramethyl-p-phenylenediamine as reference compounds, the one-electron oxidation potentials of the methyl-substituted 2-pyrazolin-5-ones were found to be in the range of 0.32-0.39 V versus normal hydrogen electrode. The relevance of these findings to the properties of the drug nafazatrom is discussed. Antipyrine was found to have a much higher oxidation potential, estimated as 1.2-1.5 V, which is rationalized on the basis of the phenyl substitution and lack of resonance stabilization of the radical cation.

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer ...

Energy Technology Data Exchange (ETDEWEB)

Transient experiments in a Temporal Analysis of Products (TAP) Reactor were performed to elucidate the role of surface oyxgen species in the oxidation of benzene to phenol on ZSM-5 type zeolites with nitrous oxide as a selective oxidant. It was shown by puls experiments with nitrous oxide that the mean lifetime of the generated surface oxygen species is between 0.2s at 500 C and about 4.2 s at 400 C. Afterwards the surface oxygen species desorb as molecular oxygen into the gas phase where total oxidation will take place if hydrocarbons are present. Dual puls experiments consisting of a nitrous oxide puls followed by a benzene puls allowed studying the reactivity of the surface oxygen species formed during the first puls. The observation of the phenol formation was impeded due to the strong sorption of phenol. Multipulse experiments were necessary to reach a ...

International Nuclear Information System (INIS)

Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of titanium silicide at the boundary of the aluminide coating and ...

International Nuclear Information System (INIS)