International Nuclear Information System (INIS)

Swelling hemoglobin CC erythrocytes stimulates a ouabain-insensitive K flux that restores original cell volume. Studies were performed with the K analog, "8"6Rb. This volume regulatory pathway was characterized for its anion dependence, sensitivity to loop diuretics, and requirement for Na. The swelling-induced K flux was eliminated if intracellular chloride was replaced by nitrate and both swelling-activated K influx and efflux were partially inhibited by 1 mM furosemide or bumetanide. K influx in swollen hemoglobin CC cells was not diminished when Na in the incubation medium was replaced with choline, indicating Na independence of the swelling-induced flux. Identical experiments with hemoglobin AA cells also demonstrated a swelling-induced increase in K flux, but the magnitude and duration of this increase were considerably less than that ...

International Nuclear Information System (INIS)

The temperature and concentration dependence of the densities of binary CaBr_2-(Li, Na, K, Rb, Cs)Br, NaBr-(Sr, Ba)Br_2 and KBr-SrBr_2 mixtures have been measured using the method of hydrostatic weighing. With exception of the systems LiBr-CaBr_2 and NaBr-(Sr, Ba)Br_2 the calculated molar excess volumes are positiv in the investigated mixtures. (author).

International Nuclear Information System (INIS)

The Monte-Carlo method and experimental methods were used to determine the neutron fluxes in the irradiation channels of the Ghana Research Reactor -1. The MCNP5 code was used for this purpose to simulate the radial and axial distribution of the neutron fluxes within all the ten irradiation channels. The results obtained were compared with the experimental results. After the MCNP simulation and experimental procedure, it was observed that axially, the fluxes rise to a peak before falling and then finally leveling out. Axially and radially, it was also observed that the fluxes in the centre of the channels were lower than on the sides. Radially, the fluxes dip in the centre while it increases steadily towards the sides of the channels. The results have shown that there are flux variations within the irradiation channels ...

International Nuclear Information System (INIS)

A gel-type "9"9Mo-"9"9"mTc generator using Titanium-Molybdate target (TiMo-target) as column packing was developed in Radioisotope Department, the Dalat Nuclear Research Institute [1]. The concentration of trace elements in TiMo-target and radionuclidic purity in "9"9"mTc solution eluted from this type of generator were studied for quality control purpose. The monostandard method in neutron activation analysis has been applied to determine the concentration of trace impurities in titanium-molybdate target. For neutron activation analysis, TiMo samples were irradiated in the different channels of nuclear reactor IVV-9 at a neutron flux of maximum 2.1 x 10"1"3 n.cm"-"2s"-"1. The following chemical element impurities were determined: Na, W, Co, Fe, Zn, Ag, Sb and Cr. The gamma ray emitted nuclides found in "9"9"mTc solution eluted from our "9"9"mTc generator were the following: "6"5Zn, "6"0Co, "1"1"0"mAg, "5"9Fe, "5"1Cr, ...

International Nuclear Information System (INIS)

The Flux Mapping System (FMS) of 540 MWe PHWR is a system, which is first of its kind used in Indian PHWRs. It is used to compute a detailed flux/power distribution of the reactor core using modal synthesis method .The paper brings out the high availability features of FMS and the software design philosophy. The paper emphasizes on framework based reusable architectural design, which simplifies and speeds up the development of data acquisition systems. (author)

International Nuclear Information System (INIS)

Included are descriptions of welding methods and joint design, welding equipment, and qualification tests.

Science.gov (United States)

Spectrophotometric method, using a ratio-recording ultraviolet-absorption spectrophotometer, permits analysis of NaMBT in ethylene glycol-water solutions with high accuracy. It reduces analysis time, requires smaller samples, and is able to detect extremely small concentrations of mercaptobenzothiazole.

Energy Technology Data Exchange (ETDEWEB)

This report is composed of the following two parts and appendix. (I) Improvement of the Method for Evaluating Reactivity Based on Monte Carlo Perturbation Theory: Theoretical formulation in Monte Carlo perturbation method had been checked, and then introduced into a calculation code. There are some cases that the results of the change of eigenvalues becomes positive or negative by changing the estimator, and there is no reasonable difference in the results between the conventional method, which does not consider the change of neutron source distribution caused by a perturbation, and the new method, which consider that change. Thus it is still necessary to check the Monte Carlo perturbation code. (II) Improvement of Nodal Transport Method for 3-D Hexagonal Geometry: We can accurately evaluate hexagonal geometry FBR core by nodal transport calculation code for hexagonal-Z geometry ...

Energy Technology Data Exchange (ETDEWEB)

We investigate a new texturization technique for crystalline silicon solar cells with sodium carbonate (Na{sub 2}CO{sub 3}) solutions. We show the dependence of the hemispherical surface reflectance on solution temperature, the etching time and the Na{sub 2}CO{sub 3} concentration. Furthermore, we investigate what element in Na{sub 2}CO{sub 3} solution influences the texturing for reducing the texturing time. As a result of experiments, we find it possible to get low reflectance in a shorter texturing time by the addition of NaHCO{sub 3}. The size of texture becomes smaller by the addition of NaHCO{sub 3} but the etching rate does not change. We conclude carbonic ion and/or its compound seems to play an important role as the initiator of pyramidal structure. This texturing method is cost effective because there is no need of expensive IPA, and the surface ...

International Nuclear Information System (INIS)

We have fabricated MgB_2 dc SQUIDs (superconducting quantum interference devices) containing inter-grain nanobridges as Josephson elements by a focused ion beam (FIB) etching method and measured their transport properties. The entire structure including the SQUID loop was patterned only using a FIB. The beam energy was 30 kV and the current was 0.9 nA for larger structures and 34 and 1.5 pA for the nanobridge pattern. Each bridge with a nominal width of 100 nm crossed a single grain boundary in the normal direction. The SQUID loop had a 3.1 #mu#m x 3.1 #mu#m hole with a 2 #mu#m average linewidth, corresponding to an inductance of 5.1 pH. The nanobridges had a two-step transition with an increase in the resistivity of more than a decade and a substantial decrease in the critical current density. Current-voltage characteristics showed a resistively shunted junction behavior at all temperatures below T_c, which implies that the current in the ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Purpose: We investigated the effects of various rinsing and healing protocols on corneal wound repair and inflammation following alkali burn in rabbits. Methods: We conducted in vitro, in vivo and ex vivo studies. First, different rinse solutions were tested in vitro after incubation of ocular cells with methanol or NaOH. Cell viability was then assessed using the neutral red test (cytofluorometry). Second, NaOH was applied to rabbit corneas and associations of rinse solutions (NaCl 0.9% or controlled ionization marine solutions) with N-acetylcysteine or vegetable oils (from Calophyllum inophyllum and Aleurites moluccana) were tested in vivo. The regeneration of the corneal epithelium and the infiltration of inflammatory cells were evaluated using in vivo confocal microscopy and e...

British Library Electronic Table of Contents (United Kingdom)

A large database (507 station-years) of daily suspended particulate matter (SPM) concentration and discharge data from 36 stations on river basins ranging from 600?km2 to 600,000?km2 in size (USA and Europe) was collected to assess the effects of SPM transport regime on bias and imprecision of flux estimates when using infrequent surveys and the discharge-weighted mean concentration method. By extracting individual SPM concentrations and corresponding discharge values from the database, sampling frequencies from 12 to 200 per year were simulated using Monte Carlo techniques. The resulting estimates of yearly SPM fluxes were compared to reference fluxes derived from the complete database. For each station and given frequency, bias was measured by the median of relative errors between estima...

Energy Technology Data Exchange (ETDEWEB)

Experimental investigations are being conducted on a single-cylinder direct-injection diesel engine to examine the transient heat transfer characteristics. Transient temperature data from stationary locations in the piston and cylinder head were used as the basis for determining the transient heat flux rates. Transient surface temperature was measured using the thin film thermocouples. At first, the transient heat flux rates calculated from the analysis method used in this paper were compared with the results from FEM. The results showed good agreement. Using this analysis method, the transient heat flux rates were calculated. The tests were performed at 1200 rpm with constant air flow. The parameters that were varied included the fuel rate and injection timing. Based on these results, the present paper discusses the mechanism of heat rejection in a direct-injection diesel engine. 8 ...

International Nuclear Information System (INIS)

This regulatory guide describes methods acceptable to the NRC staff for calculating radon fluxes through earthen covers and for calculating the resulting minimum cover thickness needed to meet NRC and EPA standards. The guide also suggests methods for obtaining the various parameters used in calculating the radon fluxes and earthen cover thicknesses and suggests default values for certain parameters. This regulatory guide is applicable to active uranium tailings sites. The NRC staff is using the methods stated in this guide as a basis for review and concurrence of DOE remedial action plans for inactive sites. The guidance is intended to be used for calculating radon flux attenuation by earthen uranium mill tailings covers. The parameter values and examples presented are limited to earthen cover materials, but the diffusion theory and the ...

Energy Technology Data Exchange (ETDEWEB)

3-Quinuclidinyl benzilate (QNB) is a potent muscarinic antagonist that binds to muscarinic acetylcholine receptors. Iodination of QNB is difficult because it contains rings that are deactivated, while phenol rings are activated. The purpose of this research is to develop an appropriate method for the iodination of QNB at no-carrier-added concentrations of /sup 125/I/NaI. Phenol was chose as the test compound for direct iodination by adding chloramine T and nonradioactive sodium iodide to the phenol in a phosphate buffer and methanol system. A simple method to radioiodinate QNB at several concentrations was developed in situ in the presence of QNB, thallic trifluoroacetate /sup 125/I/NaI, /sup 127/I/NaI, and aluminium chloride. Using milligram amounts of QNB (7.12 x 10/sup -6/ moles), three reaction steps were involved: QNB was reacted with thallic trifluoroacetate at 60/sup 0/C for ...

British Library Electronic Table of Contents (United Kingdom)

An analytical method was proposed for calculating radiative fluxes incident on a planar circular detector from a volume multiple point chemi- or bio-luminescent source inside a coaxial cylindrical reactor. The method was designed for a cylindrical reactor when the surface reflections were neglected and when chemi- or bio-luminescence reaches a detector embedded in the same homogeneous optical medium as the point emitters of the volume multiple point source model. The radiative fluxes from arbitrarily distributed point emitters were expressed by one generalized quadruple-integral formula. Then some double- and single-integral formulas were obtained for calculating radiative fluxes from identically radiating point emitters uniformly distributed within the reactor. Selected results were compu...

Energy Technology Data Exchange (ETDEWEB)

The corrosion behavior of Alloy 800 and Type 316 stainless steel in molten NaNO/sub 3/-KNO/sub 3/ was studied at temperatures from 605/degree/C to 630/degree/C. Corrosion behavior was significantly different from that previously reported in nitrate melts at temperatures up to 600/degree/C and involved a combination of oxidation, internal nitridation and sodium metallate formation. Corrosion kinetics, determined metallographically, switched from a parabolic to a linear rate equation as temperature increased. Corrosion was uniform and resulted in metal losses on the order of 100 micronsyear at 630/degree/C. Among the alloying elements, chromium was depleted from the alloy as the result of a basic fluxing process. The kinetic equations describing chromium depletion also changed from parabolic to linear with increasing temperature. The effect of the equilibrium chemistry of the melt on the corrosion behavior of the alloys is analyzed and possible ...

British Library Electronic Table of Contents (United Kingdom)

A new numerical technique called the convolution-based particle tracking (CBPT) method is developed to simulate resident or flux-averaged solute concentrations in groundwater models. The method is valid for steady-state flow and linear transport processes such as sorption with a linear sorption isotherm and first-order decay. The CBPT method uses particle tracking to take advantage of the ability of particle-based approaches to maintain sharp fronts for advection-dominated transport problems common in groundwater modeling and because of the flexibility of the random walk method to simulate a wide range of possible forms of the dispersion tensor. Furthermore, the algorithm for carrying out the convolution and superposition calculation from particle tracking results is very efficient. We sho...

British Library Electronic Table of Contents (United Kingdom)

This paper aims to study fundamentally the impacts of membrane properties on the reactive dye removal from dye/salt mixtures by nanofiltration membranes. To begin with, two types of nanofiltration membranes of similar pore size, namely asymmetric cellulose acetate membrane and thin-film composite polyamide membrane were fabricated, and their key physical, chemical and performance properties were characterized. After that, these resultant membranes were employed to perform dye removal experiments with aqueous solutions of reactive black 5 and NaCl under different operational parameters. The dye removal rate and steady permeate flux were determined and correlated with the measured membrane properties. It was found that there were significant differences between the dye removal performances o...

Energy Technology Data Exchange (ETDEWEB)

A car-borne NaI(Tl) spectrometric system was used together with a {sup 137}Cs source to obtain realistic data in the search for unshielded and semi-shielded orphan sources. The potassium-stripped counts (PSC) method was used to estimate the influence by the shielding on the detection ability. A reduction of about 5% in the critical distance was obtained for the semi-shielded source. A curve fitting method was also developed and evaluated. Results from the curve fitting method showed inferior ability to find the source compared to the PSC method. However, it can be a useful complementary tool, for characterisation of the source shielding, and estimation of the distance from the road.

British Library Electronic Table of Contents (United Kingdom)

Abstract A method to grow the halophilic archaeon Haloferax volcanii in microtiter plates has been optimized and now allows the parallel generation of very reproducible growth curves. The doubling time in a synthetic medium with glucose is around 6-h. The method was used to optimize glucose and casamino acid concentrations, to clarify carbon source usage and to analyze vitamin dependence. The characterization of osmotolerance revealed that after a lag phase of 24-h, H. volcanii is able to grow at salt concentrations as low as 0.7-M NaCl, much lower than the 1.4-M NaCl described as the lowest concentration until now. The application of oxidative stresses showed that H. volcanii exhibits a reaction to paraquat that is delayed by about 10-h. Surprisingly, only one of two amino acid auxotrophi...

International Nuclear Information System (INIS)

The static thermophysical properties of the molten salt system like LiF-NaF-BeF_2 influence the design and construction of the fuel salt and coolant in the Molten Salt Reactor for the new generation. In this paper, the equation of state of the ternary system 0.15LiF-0.58NaF-0.27BeF_2, over the temperature range from 873.15K to 1073.15K at one atmosphere pressure, is described by using modified Peng-Robinson equation. The density of the ternary system is evaluated by this equation directly, and compared with the experimental data. Base on the equation of state, the other static thermophysical properties such as the enthalpy, entropy and heat capacity at constant pressure are evaluated by the fugacity coefficient and residual function methods respectively. The density calculated by Peng-Robinson equation is in highly agreement with the experimental data, and the enthalpy, entropy and heat capacity evaluated by such two ...

International Nuclear Information System (INIS)

A Monte Carlo method called transient curve fitting method was developed to calculate a eigenvalues by first simulating the existing neutrons and precursors in the system, then calculating the Eigen-distribution of neutron flux and calculating the a eigenvalues using the transient results based on the Eigen-distribution by the code TMCC. The results of this method are tested by calculating Godiva Benchmark problems and they agree well with the benchmark results. Then the reasonable results of Subcritical Facility in Tsinghua University are given by TMCC, and the results are compared with the experimental results measured by Rossi-a method. Even in the deep subcritical cases, the method can give results consistent with experimental results. (authors)

International Nuclear Information System (INIS)

An accurate neutronics calculation of a local thermal environment within a fast reactor presents a major challenge. A method was previously described that used Monte Carlo techniques within a macrocell to make accurate and reasonably efficient design calculations for such an environment. This method is now being further optimized for the calculation of "2"3"8Pu production in the Fast Flux Test Facility (FFTF). Here, it is not only important to determine the "2"3"8Pu production from neutron capture in "2"3"7Np, but also to calculate the production of the contamination isotope "2"3"6Pu from high-energy (n,2n) and (#gamma#,n) reactions. The power of the Monte Carlo method to automatically include geometry and energy self-shielding is retained by optimization using fission neutron source biasing in both space and energy.

International Nuclear Information System (INIS)

Radial distribution functions of liquid sodium and caesium at 100"0C have been calculated by the method of molecular dynamics with interionic pair potentials derived from Heine-Abarenkov-Shaw type model potential. The results were found to be in good agreement with recent experimental data. (Auth.).

International Nuclear Information System (INIS)

A method for enrichment of the ppb level of cadmium in water by using the coagulation of soybean protein by adding acids or its complex-forming character with heavy metal ions was investigated. After adding fixed amounts of soybean milk and 2% sodium diethyldithiocarbamate(DDTC) aqueous solution and a suitable amount of delta-gluconic lactone (delta-GL) to a sample solution, the mixture was heated to boiling in order to coagulate the protein. The coagulum(soybean curd) was separated from the suspension by centrifugation and burned to ashes with a low temperature plasma asher. Then the cadmium enriched in it was determined by atomic absorption spectrometry. Various factors such as the pH of the sample solution, the amounts of soybean milk and the collection additives, and the concentration of NaCl in the sample solution on the recovery of cadmium were examined systematically. The best recovery was obtained under the following conditions: To a ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work was to develop a method to distinguish between different ion formation processes and to determine the influence of these processes on the total number of detected monatomic ions of a certain element. A vector/matrix-formalism was developed, which describes the physical processes of sputtering, ion formation, mass separation and detection in laser-SNMS. In the framework of the method developed, based on this theoretic formalism, changes in the secondary flux contribution of the respective element were observed by comparing the detected monatomic ion yield obtained in specifically aligned (SIMS and) laser-SNMS experiments. The yields resulting from these experiments were used to calculate characteristic numbers to compare the flux composition from different surfaces. The potential of the method was demonstrated for the elements boron, iron and gadolinium by ...

International Nuclear Information System (INIS)

The complex thermally stimulated luminescence (TSL) pattern of NaAlSi_3O_8 has been analyzed on transparent and opaque varieties of natural crystals and synthetic pure powder. The existence of seven additional peaks in the range 20 to 450 "0C following X-irradiation at room temperature (RT) is reported, also evaluated by the curve fitting method. The validity of the analysis is discussed in the light of detailed trap analysis of KAlSi_3O_8. An attempt has been made to probe the excistence of high temperature peaks beyond 450 "0C using UV stimulation at RT. All the TSL peaks analyzed follow a second-order kinetic process.

Energy Technology Data Exchange (ETDEWEB)

A technique has been developed which enables the direct sputter generation of atomic negative ion beams of all members of the Group IA elements (Li, Na, K, Rb and Cs). The method is based on the use of sputter samples formed by pressing mixtures of the carbonates of the Group IA elements and 10% (atomic) Cu, Ag or other metal powders. The following intensities are typical of those observed from carbonate samples subjected to approx. = 3 keV cesium ion bombardment: Li/sup -/: greater than or equal to 0.5 ..mu..A; Na/sup -/: greater than or equal to 0.5 ..mu..A; K/sup -/: greater than or equal to 0.5 ..mu..A; Rb/sup -/: greater than or equal to 0.5 ..mu..A; Cs/sup -/: greater than or equal to 0.2 ..mu..A.

International Nuclear Information System (INIS)

The solubility of Sn(IV) oxide was determined in a dilute NaClO_4 solution with pH 2 through 12 at ambient temperature. Both oversaturation and undersaturation experiments were carried out in an inert gas glovebox where the concentration of the oxygen and carbon dioxide were less than 1 ppm. The solubility of Sn(IV) oxide was 3 x 10"-"8 mol/l at neutral pH, and increased at pH > 7.5. Equilibrium constants of soluble reactions were calculated from the experimental data, using curve fitting method. The study suggests that the solubility of Sn(IV) oxide would be higher than that provisionally used in current safety assessments of HLW disposal sites.

British Library Electronic Table of Contents (United Kingdom)

IntroductionThe elimination of microorganisms from the root canal system necessitates the use of combination of irrigating solutions to enhance their antimicrobial property. The combination of irrigants and their interaction sometimes could be detrimental to the outcome of the root canal therapy. The purposes of this study were (1) to evaluate the interaction between 7% maleic acid (MA) and 2% chlorhexidine gluconate solution (CHX) and to find out the availability of individual irrigant and (2) to determine the free available chlorine content when 7% MA was mixed with 2.5% sodium hypochlorite (NaOCl) solution. MethodsInteraction between MA and CHX was assessed by high-performance liquid chromatography. Available chlorine content in NaOCl was evaluated by the standard iodine/thiosulfate tit...

Energy Technology Data Exchange (ETDEWEB)

A versatile method for estimating the characteristics of radon transport in soil is developed. The method allows the following characteristics to be estimated: depth distribution function of the soil gas radon concentration, equilibrium radon concentration in the soil air, depth at which the radon concentration reaches its equilibrium value, radon flux density from the Earth's surface, and convective radon transport velocity. The method is based on soil gas radon concentration measurements and is appropriate in the case of relatively uniform geology. (orig.)

International Nuclear Information System (INIS)

An attempt was made for early quantitative assessment of the severety of an injury, using the nuclear acids (NA) content as a biochemical indicator. Sexually mature male rats with body mass 160-180 g were irradiated with doses 0.5, 1, 2, 4 and 8 Gy of "1"3"7Cs source. Uneven irradiation was achieved by shielding the abdominal-lumbar area with lead rings, measuring 2,5/50 mm. A 28-30% fall of the dose beneath the shielded zone was thus provided. Dose-dependent quantitative changes in Na content were determined on hours 24 and 72 within the range from 0.5 to 8 Gy and followed up until day 30 after irradiation with nonlethal (2 Gy) and lethal (8 Gy) doses. The total NA content in the leucocytes was determined by the method of Kritski and Aleksandrov. The uneven irradiation of rats within the 0,5-8 Gy range induced early dose-dependent changes in NA content. The nature of their ...

Energy Technology Data Exchange (ETDEWEB)

Finite-difference acoustic-wave modeling and reverse-time depth migration based on the full wave equation are general approaches that can take into account arbitrary variations in velocity and density and can handle turning waves as well. However, conventional finite-difference methods for solving the acoustic- or elastic-wave equation suffer from numerical dispersion when too few samples per wavelength are used. The flux-corrected transport (FCT) algorithm, adapted from hydrodynamics, reduces the numerical dispersion in finite-difference wavefield continuation. The flux-correction procedure endeavors to incorporate diffusion into the wavefield continuation process only where needed to suppress the numerical dispersion. Incorporating the flux-correction procedure in conventional finite-difference modeling or reverse-time migration can provide finite-difference solutions with no numerical dispersion even ...

Energy Technology Data Exchange (ETDEWEB)

Doubly-excited 2s{sup -1}2p{sup -1}3pnp autoionizing resonance series of Ne atom as well as autoionizing resonances in the 2s region of Na and Mg atoms have been studied with monochromatized synchrotron radiation. Use of charge-separated photoion-yield method allowed us to detect these weak resonances in a clarified way in the yield curves of doubly-charged ions. The observed resonance states have been interpreted with the help of MCDF calculations, and the decay processes of these resonance states are discussed briefly.

International Nuclear Information System (INIS)

Description or function: WLUP contains validated WIMS-D formatted cross section libraries in 69 and 172 energy group structures for nuclear reactor calculations. Materials from recently released evaluated nuclear data libraries are included. The NJOY nuclear data processing system was applied for generating the cross section files following the models and conventions built into the WIMS-D lattice code. The relevant features for the WIMS users are: - Energy group structures: 69 and 172 energy groups. - List of materials: WIMS ID, general information, source of data. - Cross sections: 69 and 172 group plots. - Resonance data: WIMS ID, temperature, background cross sections. - Goldstein-Cohen factors: Goldstein-Cohen lambda values. - Thermal scattering data: thermal scattering laws and P1 matrixes. - Fission spectrum: fission spectrum data. - Burnup data: burnup chains. - Fission product yields: fission yield tables. - Pseudo lumped fission product: Description of pseudo fission product. ...

Science.gov (United States)

The relationship between the fluxes of the two strongest UV emission lines and flux in the continuum

International Nuclear Information System (INIS)

Sodium is one of the most essential elements needed for metabolic processes amongst human beings. It is consumed in the form of sodium chloride but it is also present in edible plant leaves. Sodium is mostly analyzed by flame photometric method, a destructive and time consuming technique. Sodium has been determined in some green leave vegetables samples-palak, radish, khatta palak (ambat chuka), chaulai leaves, chauli bean covers and its seeds by instrumental neutron activation analysis. The method involves irradiation of samples with thermal neutrons from "2"4"1Am-Be source and counting "2"4Na activity (half life 15 hr) from the reaction "2"3Na(n,#gamma#) "2"4Na. Activity due to 1.37 MeV photopeak was counted with a NaI(Tl) crystal coupled to gamma ray spectrometer. Green leaves of the vegetables were thoroughly washed, dried at constant temperature and ...

Energy Technology Data Exchange (ETDEWEB)

As a series of experimental determinations of the thermal diffusivity of molten alkali halides, this paper describes measurements on five molten alkali metal chlorides (LiCl, NaCl, KCl, RbCl, and CsCl) in the temperature range up to 1440 K by the forced Rayleigh scattering method. K[sub 2]Cr[sub 2]O[sub 7] is employed as a dye substance to color the transparent molten salts. In comparison with the present results converted into thermal conductivity, most of the previous experimental data obtained by steady-state methods show larger values, up to about five times, which may be due to the systematic error caused by the presence of convection and radiation. It is found that the thermal conductivity of these series of molten alkali metal chlorides decreases with increasing molecular weight, and their temperature coefficients are weakly negative. 24 refs., 9 figs., 6 tabs.

Energy Technology Data Exchange (ETDEWEB)

A survey is given by the authors of methods of removing the sulphur dioxide content of fumes which can be linked together with producing useful final products. From these technologies those suppling well utilizable gypsum, the Walther process, producing ammonium sulphate, the Wellman-Lord and Bergbau-Forschung processes, respectively adapted to produce sulphuric acid or sulphur, may be of interest. Also in the method of fumes desulphurisation by catalysis by manganese, developed in KBFI, utilizable final products are given. Background of the work of developing this method. Detailed description of the manganese catalytic method based on the use of a red mud desulphurizing agent. By this process, in addition to desulphurizing fumes, enriched red mud with reduced Na/sub 2/O content is produced, which as an iron carrier, is to be reckoned with, or to be used in the cement industry for ...

Science.gov (United States)

The technology for flue gas desulfurization (FGD) with seawater is widely adopted by coal-fired power plants in coastal areas. SO2 in the flue gas is absorbed by alkaline seawater and transfered in aqueous phase as sulfite (SO3(2-)), and most SO3(2-) is transformed to sulfate (SO4(2-)) after an aeration process. The remaining SO3(2-) in the seawater discharged to sea area may be harmful to marine organism because of its biological toxicity, thus it is necessary to determine the concentration of SO3(2-) in the seawater for desulfurization. In this study, the method of determination of SO3(2-) in the seawater by ion chromatography was investigated. The separation was achieved on an IonPac AS14A column with 14 mmol/L NaOH-12 mmol/L Na2 CO3 solution as the mobile phase at a flow rate of 1.2 mL/min, and the detection was performed by a pulsed amperometric detector. Formaldehyde was added as a protective agent when sampling ...

Energy Technology Data Exchange (ETDEWEB)

Performance assessments for the Area 5 Radioactive Waste Management Site on the Nevada Test Site have used three different mathematical models to estimate Rn-222 flux density. This study describes the performance, uncertainty, and sensitivity of the three models which include the U.S. Nuclear Regulatory Commission Regulatory Guide 3.64 analytical method and two numerical methods. The uncertainty of each model was determined by Monte Carlo simulation using Latin hypercube sampling. The global sensitivity was investigated using Morris one-at-time screening method, sample-based correlation and regression methods, the variance-based extended Fourier amplitude sensitivity test, and Sobol's sensitivity indices. The models were found to produce similar estimates of the mean and median flux density, but to have different uncertainties and sensitivities. When ...

International Nuclear Information System (INIS)

An explicite PN solution of the multi-dimensional homogeneous neutron transport equation is given by expanding the angular flux into a series of geometry-independent spherical harmonics operators. An algorithm is developed for representing the spherical harmonic operators in orthogonal curvilinear coordinates. The general formulae are applied to two-dimensional spherical geometry; detailed P3 formulae are given. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Thermal absorption with its combined thermal and mechanical loads in a solar receiver does depend significantly on the distribution of incident solar radiation. For a cavity receiver with paraboloid collectar a method is derived which enables the calculation of solar radiation distribution on the areas inside the receiver. The theoretical bases are presented first, and a subsequent example shows the influence of the most important geometric parameters on the distribution of solar radiation.

Energy Technology Data Exchange (ETDEWEB)

Depth dose distributions for protons in the energy range from 2 to 600 MeV have been calculated by Monte Carlo and analytical methods. The dependence on energy of Maximum Dose Equivalent (MDE), quality factor and isotropic factor recommended for practical use are presented. The problems connected with regulation of maximum permissible proton fluxes are discussed. (author).

Energy Technology Data Exchange (ETDEWEB)

This work was made with the purpose to complete information about the hydrolysis constants of Europium (III) in high ion strength media. So it was determined at a ion forces media 4, 5 and 6 M of sodium perchlorate at 303 K. The method used was the potentiometric with the aid of the Super quad computer program. In high ion strength media, the measurements of p H do not correspond directly to negative logarithm of the concentration of hydrogen ions, by this it is necessary to calibrate the electrode in these conditions. The Europium was hydrolized at pC{sub H} values greater 6 in all cases. The potentiometric method used under the described experimental conditions is adequate to determine the hydrolysis constants of Europium (III). According to the results and diagrams of chemical species of Europium obtained we can conclude that the hydrolysis constants, differ by its distribution but not in its identity. (Author)

Science.gov (United States)

Cardiac contractile function is dependent on the integrity and function of the sarcolemmal membrane. Swimming exercise training is known to increase cardiac contractile performance. The purpose of the present study was to examine whether a swimming exercise program would alter sarcolemmal enzyme activity, ion flux, and composition in rat hearts. After approximately 11 wk of exercise training, cardiac myosin and actomyosin Ca2+-adenosinetriphosphatase (ATPase) activity was significantly higher in exercised rat hearts than in sedentary control rat hearts. Glycogen content was increased in plantaris and gastrocnemius muscles from exercised animals as was succinic dehydrogenase activity in gastrocnemius muscle of exercised rats in comparison to sedentary rat preparations. Sarcolemmal vesicles were isolated from hearts of exercise-trained and control rats. Sarcolemmal Na+-K+-ATPase and K+-p-nitrophenylphosphatase activities, ...

Energy Technology Data Exchange (ETDEWEB)

The damping of unwanted oscillations in the generator units after a failure can be realized by installing a stabilizer between f.e. the revs of the generator and an input of the voltage regulator. The tuning of a Power System Stabilizer (PSS) is investigated using bode plots. Eigenvalue analysis shows an enlarged system stability margin. The method was tested on an advanced analogue power system simulator. As a result of these tests it appears to be useful to consider the stability as well as the optimal tuning. 5 figs., 6 refs.

Energy Technology Data Exchange (ETDEWEB)

A study is made of plant sensitivity to mutagens during the processing of seeds. An examination is made of problems concerned with modification mutability, the nature of plant restoration following irradiation. Particular attention is given to mutation changes. A presentation is made of several features of mutant changes initially selected by separate indicators. An examination is made of the possible study of mutant indicator genetics. General data on the forms and varieties produced by the mutagenesis method are given. The book is designed for breeding specialists and geneticists engaged in the study of mutagenesis. 439 references, 27 figures, 66 table.

International Nuclear Information System (INIS)

A numerical and experimental investigation is carried out in a solar thermochemical reactor for the thermal dissociation of ZnO at 2000 K using concentrated solar energy. The reactor consists of a cavity-receiver lined with ZnO particles and directly exposed to high-flux irradiation. A transient heat transfer model is formulated to link the rate of radiation, convection, and conduction heat transfer to the reaction kinetics. The radiosity and Monte Carlo methods are applied to obtain the distribution of net radiative fluxes at the internal surfaces of the reactor cavity and at the surface of the ZnO bed. Validation is accomplished in terms of the calculated and measured transient temperature profiles and chemical reaction rates.

Energy Technology Data Exchange (ETDEWEB)

In this study the soil/vegetation/atmosphere-model based on the formulation of Deardorff was refined to hour basis and applied to a field in Vihti. The effect of model parameters on model results (energy fluxes, temperatures) was also studied as well as the effect of atmospheric conditions. The estimation of atmospheric conditions on the soil-vegetation system as well as an estimation of the effect of vegetation parameters on the atmospheric climate was estimated. Areal surface fluxes, temperatures and moistures were also modelled for some river basins in southern Finland. Land-use and soil parameterisation was developed to include properties and yearly variation of all vegetation and soil types. One classification was selected to describe the hydrothermal properties of the soils. Evapotranspiration was verified against the water balance method

Energy Technology Data Exchange (ETDEWEB)

Water vapor is well known to be a critical component in many aspects of atmospheric research, such as radiative transfer and cloud and aerosol processes. This requires both improved measurements of the columnar water vapor and its profiles in the atmosphere in a wide range of conditions, and adjustment of water vapor parameterizations in radiation codes including the perfection of spectroscopic parameters. In this paper we will present the results of comparison of our calculations and downward solar fluxes measured with Rotating Shadowband Spectroradiometer under conditions of horizontally homogeneous clouds. We also will discuss the sensitivity of atmospheric radiation characteristics to variations of water vapor in the band 940 nm: these results may be useful for development of new methods of retrieval of the total column water vapor content (WVC) in the atmosphere from data of radiation observations.

International Nuclear Information System (INIS)

The authors have developed a high-sensitivity real-time neutron radiography (NR) system by the use of the low power reactor of Kinki University. The system was constructed with a high efficiency neutron-photon converter, an image intensifier and a SIT TELEVISION camera. Some digital image processing techniques were applied for improving the quality of the real-time neutron images. By the use of this system, dynamic neutron imaging was performed successfully under the condition of a weak neutron field that was about two orders of magnitude lower than that of the standard NR system. The neutron flux, calculated from the fluctuation of the neutron response of the images, was nearly equal to the value measured by the foil activation method. From this fact, the efficiency for the neutron detection of the imaging system was estimated to be almost 100%. For the purpose of developing a system with higher sensitivity, consideration of neutron statistics ...

International Nuclear Information System (INIS)

The principle is described of X-ray fluorescence analysis and the manner of detecting the emitted characteristic radiation. The advantages are presented of radionuclide X-ray fluorescence analysis which consist primarily in the possibility of conducting a totally non-destructive analysis, and of accurate and relatively narrow localization of the analyzed area, the simultaneous qualitative and quantitative determinations of a large number of elements in the order of concentrations 10"1 to 10"-"4%, stability of excitation radiation flux, simple design and relatively low capital costs. The so-called matrix effect is pointed to. A number of examples is given of the use of the cited method, including its use in the analysis of art objects. (J.B.).

Science.gov (United States)

This report describes an improved method of remotely identifying irradiated nuclear fuel assemblies. The method uses existing in-cell TV cameras to input an image of the notch-coded top of the fuel assemblies into a computer vision system, which then produces the identifying number for that assembly. This system replaces systems that use either a mechanical mechanism to feel the notches or use human operators to locate notches visually. The system was developed for identifying fuel assemblies from the Fast Flux Test Facility (FFTF) and the Clinch River Breeder Reactor, but could be used for other reactor assembly identification, as appropriate.

International Nuclear Information System (INIS)

The purpose of this work was to develop and evaluate a method of locating breached fuel within the Fast Flux Test Facility (FFTF) reactor based on the relative response of the delayed neutron monitors (DNM) located on each of the three primary sodium cooling loops. The primary method of location is the use of tag gas containing unique ratios of the noble gases xenon and krypton. Although the tag gas system works quite well, it is relatively expensive because of the costs of preparing and loading the gas into each fuel pin. Triangulation of DNM signals could potentially decrease tag gas costs while maintaining overall location reliability.

International Nuclear Information System (INIS)

A modified accumulator was devised to measure surface radon flux from porous media. It consists of a collector hood accumulator with a homogenizer pump and a pressure balancer. The latter was used to compensate for any pressure changes produced during sample withdrawl and hence eliminate additional radon transport from media. Errors resulting from radon back diffusion due to decreasing concentration gradient with time across the interface were eliminated by measuring radon concentrations in the accumulator for two different periods of time and calculating the true radon flux, J(o), from the solution of a time-dependent radon transport equation. Core samples from the observation site were withdrawn for laboratory determination of pkrosity, moisture content, bulk and grain densities, Ra-226 source concentration and the fraction of Rn-222 produced in the void volume. The data were used to calculate the radon diffusion coefficient for the media. ...

UK PubMed Central (United Kingdom)

1. In rat soleus muscle, high frequency electrical stimulation produced a rapid increase in intracellular Na+ (Na+i) content. This was considerably larger in muscles contracting without developing tension...Full Text Available

UK PubMed Central (United Kingdom)

Na⁺ channels are often spliced but little is known about the functional consequences of splicing. We have been studying the regulation of Na⁺ current inactivation in an...Full Text Available

International Nuclear Information System (INIS)

The University of Virginia's real-time neutron radiography facility was characterized by measurement of the total neutron flux, gold/cadmium ratio, neutron/gamma ratio, and the effective collimar length-to-aperture diameter (L/D) ratio. The real-time neutron imaging system and collimator were further characterized by measuring the modulation transfer function (MTF) of the system. The collimator effectiveness was measured by using the MTF to determine the ''unparallelism'' of the neutron beam. The computer-based image processing system allowed rapid calculation of the MTF and the collimator effectiveness. The results of these measurements, using no collimator and a simple tube collimator, demonstrated the method's ability to determine the effective L/D ratio. The MTF measurement scheme provided a fast, reliable, and reproducible means of monitoring any changes in the real-time system, including both the neutron beam and the electronic ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanical supported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the MgO(MG-S) with Copper and ...

Energy Technology Data Exchange (ETDEWEB)

A thermal-resistant radiation sensing system using optical fiber has been developed. The system is for monitoring progress of chemical decontamination and able to measure the gamma-ray level in a hot solution of decontamination chemicals in situ. Our sensor head makes use of thermal-resistant NaI (T1) and it is connected to an optical fiber bundle. Scintillation photons pass from the NaI (T1) into the end of the bundle. This part of the system can withstand temperatures of over 100degC. At the far end of the optical fiber bundle, the scintillation photons are converted into fluorescent photons using a wavelength-shifting fiber. These photons are transferred to a distant photomultiplier tube through two thin transparent optical fibers. Furthermore, we propose a self-compensation technique for the dependence of scintillator sensitivity on. This compensation method is based on the correlation between temperature, sensitivity, ...

British Library Electronic Table of Contents (United Kingdom)

Abstract The present work, regarding the determination of ultratrace Os(VIII), Ru(III) and Ir(III) in superficial waters is an interesting example of the possibility to simultaneously, or better sequentially determine each single element in real samples by voltammetry. The method is based on the catalytic current of the Os(VIII)- and Ru(III)-bromate systems by square wave voltammetry and on the Ir(III) determination by square wave catalytic adsorptive stripping voltammetry. 0.5-mol-L-1 acetate buffer pH-4.9+7.710-2-mol-L-1 NaBrO3 and 0.5-mol-L-1 acetate buffer pH-4.9+7.710-2-mol-L-1 NaBrO3+2.310-5-mol-L-1 cetyltrimethylammonium bromide (CTAB) +0.2-mol-L-1 KCl were employed as the supporting electrolytes. The analytical procedure was verified by the analysis of the standard reference materi...

British Library Electronic Table of Contents (United Kingdom)

Abstract Many (K1-xNax)NbO3 (KNN)-based ceramics with high piezoelectric performance exhibit undesirable strong temperature dependence due to the orthorhombic-tetragonal polymorphic phase transition near room temperature. In order to improve the temperature stability of the ceramics, many additives have been added into the KNN-based ceramics to shift TO-T down to below room temperature. Contrary to the previous approach (Na0.53K0.47-xAgx)Nb1-xSbxO3 (NKANS) ceramics with TO-T well above room temperature have been prepared by a conventional solid-state reaction method. The density and the electrical properties are effectively improved by the addition of AgSbO3, and optimum piezoelectric properties are found in the ceramics with 0.05---x---0.07, with maximum kp---0.46 for NKANS5 and maximum d...

British Library Electronic Table of Contents (United Kingdom)

There are mainly two protocols in isoflavone analysis, one that involves hydrolysis prior to HPLC analysis and the other direct HPLC analysis. In this study, three different hydrolysis methods were systematically re-evaluated, and compared with direct HPLC analysis. Acidic hydrolysis (1.2-3M HCl in ethanol at 80^oC) showed a maximum conversion of ca. 92% from glucosides to aglycones in 2h; however, longer reaction caused degradation of genistein. Alkaline hydrolysis using 2M NaOH converted acetylglucosides and malonylglucosides to their respective glucosides within 10min. Glucuronidase from H. pomatia effectively converted isoflavone glucosides and acetylglucosides to aglycones. Quantification of the total isoflavones in various soy food products showed no significant difference among dire...

Energy Technology Data Exchange (ETDEWEB)

The measurement of local heat transfer coefficients is necessary to record the basic phenomena of heat transfer in thin-film apparatuses. For this reason the so-called electrochemical analogy method was developed and used for this application. The electrochemical method implies a specifically composed electrolyte which substitutes the fluid to be evaporated in the thin-film apparatus. Using the redox electrolyte (0,025 kmol/m/sup 3/ K/sub 4/Fe(CN)/sub 6/ resp. k/sub 4/Fe(CN)/sub 6/ and 2nNaOH) the viscosity was, for the first time, thickened until 0.4 Pa s by the help of hydroxyethyl-cellulose.

International Nuclear Information System (INIS)

The formation constants of species formed in the system H"+"+alanine and VO_"2"+alanine have be determined in aqueous solution for 1.0NaCIO_4,using a combination of pramiracetam and spectrophotometric techniques. The compositions of the formed complexes and their stability constants were determined ny curve fitting method and it was shown that di oxovanadium(V) forms two mononuclear 1:1 and 1:2 species with alanine of the type VO_2L and VO_2L_2 The protonation constant of the amino group of alanine has been determined using a computer program which employ a least-squares method. The defence of the protonation of alanine and the stability constant of the species on ionic strength are described by a Debby-huckel type equation.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Czech Academy of Sciences Repository

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A method has been developed to optimize the energy resolution of a horizontally focusing monochromator. The method consists of determining the optimum radius of curvature of the cylindrically bent monochromator crystal by minimizing the total diffracted X-ray flux measured through an X-ray absorption foil. When measured at an absorption edge a global minimum can be identified, which corresponds to the minimum energy band accepted along the entire length of the crystal. Experimental verification of this method has been validated by comparing X-ray fluorescent scans taken for a series of crystal curvatures and by directly measuring the X-ray beam profiles at the corresponding points. The actual optical configuration and asymmetric-cut parameter of the focusing monochromator on beamline X4C at the National Synchrotron Light Source are modeled and ray tracing simulations of the optical system are compared ...

Energy Technology Data Exchange (ETDEWEB)

Numerical solutions given by a vorticity-velocity method are presented for combined free and forced laminar convection in the thermal entrance region of a horizontal rectangular channel without the assumptions of large Prandtl number and small Grashof number. The channel wall is heated with a uniform wall heat flux. Typical developments of temperature profile, secondary flow, and axial velocity at various axial positions in the entrance region are presented. Local friction factor and Nusselt number variations are shown for Rayleigh numbers Ra = 10{sup 4}, 3 {times} 10{sup 4}, 6 {times} 10{sup 4}, and 10{sup 5} with the Prandtl number as a parameter. The solution for the limiting case of large Prandtl number and small Grashof number obtained from the present study confirms the data of existing literature. It is observed that the large Prandtl number assumption is valid for Pr = 10 when Ra {le} 3 {times} 10{sup 4} but for a larger Prandtl number ...

Energy Technology Data Exchange (ETDEWEB)

Two-phase pressure drop and fluctuating static pressures were measured in a small horizontal rectangular channel (hydraulic diameter = 5.44 mm). The two-phase fluid was an air/water mixture at atmospheric pressure tested over a mass flux range of 50 to 2,000 kg/m[sup 2] [center dot] s. Two-phase flow patterns were identified and an objective method was found for determining the flow pattern transition from bubble or plug flow to slug flow. The method is based on an RMS static pressure measurement. In particular, it is shown that the transition is accompanied by a clear and abrupt increase in the RMS pressure when plotted as a function of mass quality. Use of the RMS pressure as a two-phase flow pattern transition indicator is shown to have advantages over pressure-versus-time trace evaluations reported in the literature. The transition is substantiated by a clear local change in slope in the curve of two-phase pressure drop ...

Energy Technology Data Exchange (ETDEWEB)

Pitting corrosion and trans-passive dissolution of 316 stainless steel in solution containing five percent of commercial bleaching liquid was investigated by employing potentiodynamic polarization method and recording corrosion potential during immersion. Today commercial bleaching liquids are widely used as cleaner additives, therefore, those house appliances made from stainless steels are in contact with aqueous solution containing bleaching liquid. This may cause sever localized corrosion and trans-passive dissolution. In order to investigate the possibility of trans-passive dissolution of stainless steel by bleaching liquid, potentiodynamic polarization and recording variation of corrosion potential of specimens were carried out in 0.2 M Na{sub 2}SO{sub 4} solution containing 5 %wt. commercial bleaching liquid. A 500 mV drop in trans-passive potential and also instantaneously ennobling corrosion potential revealed the possibility of ...

Energy Technology Data Exchange (ETDEWEB)

The thermal modeling of electrochemical batteries is today an integral part of the design and validation operations of new products. The Li-ion pair allows to increase the power density of batteries but leads to higher heat fluxes during charging-output cycles. Thus, the thermal control has become more crucial and requires the use of modeling. SAFT and TSR companies are involved in this approach and use the ESACAP software. This paper presents this software which uses a nodal method for the modeling of the coupled thermal and electrical processes that take place inside elementary cells and batteries. (J.S.)

International Nuclear Information System (INIS)

Axial offset anomaly (AOA) is caused by the deposition of crud on the fuel cladding of a PWR. When significant levels of crud build up on the cladding, boron can accumulate in the pores of the crud as a concentrated solution or solid phase, and cause the flux depression. Numerous studies have been conducted on the primary water chemistry to reduce the amount of crud in the primary circuit to avoid radioactivity buildup and unexpected power transition in the plant. However, experiments on the crud are restricted in the laboratory because the crud is a highly radioactive material. The objective of this study is to develop a test method for simulating the deposition of crud in a nuclear power plant

Science.gov (United States)

Numerical solutions for fully developed laminar flow in internally finned tubes with trapezoidal and triangular fin profiles were given with Finite Element Method (FEM): The heat transfer characteristics were obtained and compared under the boundary conditions of uniform heat flux, uniform wall temperature, and the third boundary condition with finite wall thermal conductivity considered. The numerical results show that boundary conditions have pronounced effects on the temperature field. Furthermore, a new mechanism on the heat transfer augmentation of internally finned tubes is proposed.

CERN Document Server

We provide a both qualitative and quantitative comparison among different approaches aimed to solve the problem of non-linear diffusive acceleration of particles at shocks. In particular, we show that state-of-the-art models (numerical, Monte Carlo and semi-analytical), even if based on different physical assumptions and implementations, for typical environmental parameters lead to very consistent results in terms of shock hydrodynamics, cosmic ray spectrum and also escaping flux spectrum and anisotropy. Strong points and limits of each approach are also discussed, as a function of the problem one wants to study.

Energy Technology Data Exchange (ETDEWEB)

Among the membrane filtration techniques, continuous cross-flow ultrafiltration (UF) is an innovative method to separate solid/liquid or liquid/liquid phases at a lower pressure of 5--150 psi compared to reverse osmosis (RO) in which the applied pressure is an order of magnitude higher. Recently, attempts have been made to combine processes of UF and other treatments for many applications. However, there is very little knowledge about the filtration process which combined coagulation and UF, and very few attempts have been made to apply coagulated UF to the treatment of fuel oil contaminated water. During the UF treatment of organic contaminants rapid declines in flux will occur due to the membrane fouling. Oil as a foulant plants an important role in the flux decrease. However, there are very limited pretreatment processes which can effectively remove fuel oil from water and hence solve the fouling problem. The purpose of ...

International Nuclear Information System (INIS)

The use of europium as a local structural probe allows the various phases appearing in the NaCaPO_4-Na_3Eu(PO_4)_2 and NaSrPO_4-Na_3Eu(PO_4)_2 systems to be detected. The broadening of the europium emission lines in going from the calcium to the strontium phases illustrates the ease of displacement of the PO_4 groups. (Auth.).

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

As the last step of urinary acidification, the inner medullary collecting duct (IMCD) is thought to secrete protons into the tubular lumens by means of a H(+)-translocating adenosinetriphosphatase (H(+)-ATPase). However, recent studies have also shown the existence of Na(+)-H+ exchange activity in IMCD cells. Although the physiological function of the antiporter in IMCD cells is unknown, activation of Na(+)-H+ exchange in other cell-culture systems has been suggested to be closely associated with the process of cell growth. Thus presence of Na(+)-H+ exchange may relate to the growth phase of these cells. To examine intracellular pH (pHi) regulation in growing IMCD cells, we studied proton transport by Na(+)-dependent and Na(+)-independent mechanisms by microfluorimetry using the pHi-sensitive dye 2',7'-bis(carboxyethyl)-5,6-carboxyfluorescein acetoxymethyl ester ...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The results of X-ray and neutron diffraction experiments on molten alkali halides in which some data of our experiments by X-ray diffraction such as those of molten LiCl, NaCl, KCl, LiBr and KBr are included were summarized. The first peak positions in the radial distribution function in molten alkali halides by X-ray or neutron diffraction experiments are always longer than those by computer simulations and the differences of 0.1 -- 0.3 A exceed the experimental error. It seems to be due to the deformation of the electron shell. In the computer simulation, the shell model which has the spherical deformation was expected to have more closer value of the first peak position to the experimental one than the rigid ion model by taking the polarization of ions. However, no change in the first peak position was found. Therefore, the non-spherical deformation of electron shell at the point where ions are in contact with each other has to be taken into account. The neutron ...

Energy Technology Data Exchange (ETDEWEB)

Anode polarization measurement is performed in mixed solution of NaCl and NaF using SUS 304 steel to investigate whether F[sup -] promotes or inhibits pitting corrosion. Pitting corrosion does not occur in the solution of NaF only, but passive state is broken above a certain critical potential, resulting in overall dissolution. When anode polarization measurement is made in a solution of fixed concentration NaCl added with NaF, pitting corrosion is inhibited at a certain critical concentration. F[sup -] has no effect on corrosion potential in the solution up to this critical concentration. Overall dissolution occurs in the solution with higher concentration than the critical concentration, the current value at that time agrees with that in the solution of NaF alone, and no effect of Cl[sup -] is shown. The concentration range where pitting corrosion occurs and ...

Energy Technology Data Exchange (ETDEWEB)

Creation of new multi-composite materials is an essential issue to attain an innovative improvement of the current nuclear technology. In this paper, some highlights are focused on the research of creation of those materials and the relating subjects in NIRIM. (1) The KOH corrosion test method are expected to be efficiently available in the limited cases instead of Na corrosion test one. (2) The preliminary creation of the multi-composite ceramics were achieved by Y- ion implantation into sapphire and the RF sputtering, of which the specified orientation was realized by the existence of the buffer layer. The importance of the defect control are described with the relation to the corrosion resistance improvement. (3) The ion beam induced phenomena have been investigated on the surface change of silica glass and the crystallization of Cu film on SrTiO{sub 3}. (4) The electronic states of the alkali-metal adsorbed surfaces and that of the ...

Energy Technology Data Exchange (ETDEWEB)

Modeling calculations on the solubility of americium have indicated that basic americium carbonate, and not americium trihydroxide, is the solubility-controlling solid in the pH range from 6 to 10 under the influence of atmospheric CO{sub 2}. The solubility of crystalline {sup 243}AmOHCO{sup 3} has been investigated in batch experiments in near-neutral and basic solutions as a function of dissolution time in 0.1 M NaClO{sup 4} at room temperature under oxic conditions. After the solutions reached steady-state conditions, the influence of dissolved solids on the americium concentration in the supernatant solution was studied by utilizing several experimental methods to separate the solution phase from the solid. The solids were characterized by X-ray powder diffraction analysis.

Energy Technology Data Exchange (ETDEWEB)

The passive films formed on 316L stainless steel in various NaCl solutions have been investigated by capacitance measurements (Mott-Schottky). Pitting parameters have been determined using the galvano-kinetic polarisation method. The obtained results reveal the existence of a shallow and a deep donor level localised in the band gap of the semiconducting oxide film. These energy levels are due to iron ions in the tetrahedral and octahedral positions. It also appears that the participation of the deep donor level effects the electric field. The study developed allows us to compare characteristic parameters of the electronic structure of the passive film to those related to pitting susceptibility. (authors) 25 refs.

British Library Electronic Table of Contents (United Kingdom)

Background/Aims Serum free fatty acid (FFA) composition and abnormal fatty acid metabolism have been implicated in the pathogenesis of nonalcoholic steatohepatitis (NASH). Therefore, we determined if the serum FFA composition can provide accurate diagnosis of NASH. Methods We compared fasting serum FFA compositions in 20 patients with simple steatosis to those in 77 patients with NASH, including 65 patients with early-stage NASH. Results By univariate analysis, the proportions of serum free myristic acid (P?=?0.002) and palmitoleic acid (P?=?0.033) and the stearoyl CoA desaturase (SCD)-1 index (P?=?0.047) were significantly elevated in NASH patients in comparison to patients with simple steatosis. Only the serum free myristic acid proportion was significantly elevated in the early-stage NA...

International Nuclear Information System (INIS)

Formation of the complex of the univalent astatine cation with nitrilotriacetic acid (AtL)"2"- and its stability constant (lgK_1=8.97(4), 25degC, #mu#=0.1) have been found experimentally for the first time. The complex is stable in perchlorate solutions in presence of 5 . 10"-"3 mol . l"-"1 of the oxidizer Na_2S_2O_8 in the interval 4#<=#pH#<=#8.5. The complex is supposed to be destroyed in weak alkaline solutions by reduction of astatine to astatide. The deprotonation constant of hypoastatic acid pK_d_p=5.23(9) was found to be lower than determined previously. The investigation was carried out by the method of ion electrophoresis in free electrolyte solutions. (orig.).

CERN Document Server

CR-39 detectors have been exposed to a 5.9-MeV antiproton beam using the low energy antiproton ring (LEAR) facility at CERN. At this energy, tracks of antiprotons appear in a CR-39 detector after 135 min of etching in 6 M NaOH at 70C. Fluence of the antiproton beam has been determined using track density. We have also found tracks in the etched CR-39 detector at different depths (250-500 mum). These tracks have resulted from the annihilation of antiprotons with the constituents (H, C and O) of the CR-39 detector. The goal of the experiment is to develop a simple and low-cost method to study properties of antiparticles and those formed after annihilation of these particles with the target matter.

British Library Electronic Table of Contents (United Kingdom)

Summary Background Sorafenib is an oral multikinase inhibitor that blocks cell proliferation via the ERK pathway and angiogenesis via the VEGF pathway. This phase II trial was conducted to determine the efficacy and tolerability of sorafenib for the treatment of patients with metastatic urothelial cancer (UC) who had not had prior chemotherapy for advanced disease. Patients and Methods Seventeen chemo-na?ve UC patients with adequate performance status and organ function were treated with sorafenib 400?mg twice daily on a continuous basis until progression or unacceptable toxicity. The primary endpoint was objective tumor response rate as measured by RECIST criteria. Secondary endpoints included rate of prolonged stable disease (>3?months), time to progression, median and 1?yr survival and ...

International Nuclear Information System (INIS)

We consider a SQUID ring inductively coupled to an electromagnetic field mode, both treated quantum mechanically. We demonstrate a method for creating a maximally entangled state between the ring and the field mode. Our method utilises a non-adiabatic external magnetic flux pulse to move into and out of a transition region. Hence, our approach is fundamentally different to techniques based on Landau-Zener tunnelling that can also be used to achieve similar results. Our analysis is extended to include the effects of coupling the system to a dissipative environment. With this model we show that although such an environment makes a noticeable difference to the time evolution of the system, it need not destroy the entanglement of this coupled system over time scales required for quantum technologies.

Energy Technology Data Exchange (ETDEWEB)

The utilization of electrically heated rods for the simulation of nuclear fuel pins represents a generally adopted method by the nuclear industry to study thermalhydraulic problems. Usually its is necessary to determine the time variation of the electric linear power to simulate a given nuclear power transient in order to yield the same temperature and heat flux conditions in the surface of the electrical heater that would be observed in the nuclear fuel pin. The present work analyzes the limits of the usually adopted simulation methods and shows a manner to obtain the required electrical linear power that reduces oscillations and yields accurate results for the thermal conditions of the rod surface wall. (author). 5 refs, 5 figs, 1 tab.

Energy Technology Data Exchange (ETDEWEB)

A complete code based on the finite element method (FEM) is used to study the attenuation of gamma rays, of source energy 9 MeV, in simple homogeneous lead and water systems. The results are compared, in tables and graphs, with those produced by a Monte Carlo method of solution. In the comparison, particular attention is paid to the annihilation gamma rays generated by the pair production process, to energy deposition, and to the leakage spectra. A model, multilayer, slab shield, having a fission neutron source impinging on the left-hand face, is also solved by the FEM code, using data from a coupled neutron/gamma ray cross section library. The resulting neutron and gamma ray flux distributions, and the leakage spectra, are shown graphically. (author).

Energy Technology Data Exchange (ETDEWEB)

Two measurement methods to determine the rate of neutral free radical production by the photo-deionization of negative ion beams (PDINIB) are introduced. These methods, namely, photoelectron-current measurement by low-frequency electro-modulation probe (PMMP) and measurement of decrease in the negative-ion beam current (DNIC) were employed to evaluate the production rate in a trial surface-processing apparatus developed in the author's laboratory utilizing a steady-flux refined beam of neutral free radicals (RBNR) produced by the PDINIB procedure. A {sup 63}Cu{sup -} negative ion beam of kinetic energy E{sub i} varied up to 15 keV was irradiated with a 514.5 nm visible light beam from a 25 W CW Ar{sup +} ion laser. The detection limit of the production rate by the PMMP setup was as high as 6 x 10{sup 9} s{sup -1} under the condition that E{sub i}=15 keV, the negative-ion beam current I{sub i}=4 {mu}A and the laser ...

Energy Technology Data Exchange (ETDEWEB)

A laboratory differential simulation method is used for the design of carbonization columns at coal-tar processing in which phenols are regenerated from phenolate solution by carbon dioxide absorption. The design method is based on integration of local absorption rates of carbon dioxide along the column. The local absorption rates into industrial phenolate mixture are measured in a laboratory model contactor for various compositions of the gas and liquid phases under the conditions that ensure the absorption rates in the laboratory absorber simulate the local rates in the industrial column. On the bases of the calculations, two-step carbonization columns were designed for 30000 t/year of the phenolate solution treatment by carbon dioxide. The absorption proceeds at higher pressure of 500 kPa and temperatures from 50 to 65 C, pure carbon dioxide is used and toluene is added. These conditions have the following favourable effects: (I) significant ...

Energy Technology Data Exchange (ETDEWEB)

One of the main problems facing the mining sector is the production of acid mine drainage (AMD), which is caused by the oxidation of sulphide minerals in the presence of water. AMD can have a detrimental effect on the environment. One solution is to use soil covering over the materials that cause acid to limit the gas flux by diffusion. A capillary barrier effect is generated by using various layers of different types of soil. In the composite system till and clay normally form the basis of the fine material layer. The use of low sulphide tailings to replace the use of fine grained soil was studied to evaluate its effectiveness. Following both in situ and laboratory experiments spread over an eight-year period, the results indicated that an effective method to limit the oxygen flux and generation of AMD is the use of non-acid generating tailings as the moisture retaining layer. The main concepts that form the basis of the ...

Energy Technology Data Exchange (ETDEWEB)

The technology of minor actinide recycling in fast reactors has been discussed. In CEA, the feasibility study on Am once-through recycling in Phenix core with the moderated target subassemblies (S/As) has been performed. In this report, the evaluation of the heterogeneity effect on the moderated target S/As is described. It was evaluated by the calculation with the continuous energy Monte-Carlo code, MVP, because the accuracy of the deterministic method for the moderated target S/As is unknown. The reaction rates of four isotopes (Am-241, Am-242, Am242m and Am-243) calculated with the heterogeneous model and the homogeneous one were compared. These four isotopes play the important role in Am incineration. It is seen that the homogeneous model overestimates the reaction rates of Am-241 and Am-243 by 4 - 13%, and underestimates those of Am-242 and Am-242m by 13 - 23%. Further investigation made it clear that the overestimation of Am-241 and Am-243 reaction rates is ...

International Nuclear Information System (INIS)

The efficiency of the synthesized zeolite NaY from rice husk ash (RHA) in the removal of Cr(III) from aqueous solution was studied. Zeolite NaY was synthesized from RHA via seeding technique and the identification of its structure was done by X-ray Diffraction (XRD) technique and the elemental analysis was carried out by X-ray Fluorescence (XRF). The physicochemical properties which were related to the use of the zeolite NaY as a sorbent was also investigated. The synthesized zeolite NaY has higher cation exchange capacity (CEC) than the commercial zeolite NaY due to the higher amount of sodium content in the synthesized as well as the lower ratio of silica to alumina. The synthesized zeolite NaY together with the commercial one as comparison was used in the sorption of the Cr(III) in aqueous solution by batch sorption experiments. The kinetic study showed that ...

British Library Electronic Table of Contents (United Kingdom)

This study was focused on the possibility to inactivate thermosensitive Listeria monocytogenes ATCL3C 7644 and thermoresistant 56 Ly strain by Na-Chlorophyllin (Na-Chl)-based photosensitization in vitro and on the surface of packaging. Comparative analysis of antimicrobial efficiency of photosensitization with conventional surface cleaning was performed. Data indicate that both Listeria strains, after incubation with Na-Chl and following illumination (l=400nm, 20mWcm-2), were inactivated by 7 log in vitro. This treatment cleaned both Listeria strains from packaging surfaces. Comparative analysis indicates that washing with water diminishes pathogens by less than 1 log, 200ppm Na-hypochlorite by 1.7 log, Na-Chl-based photosensitization by 4.5 log. Listeria biofilms were totally removed from...

International Nuclear Information System (INIS)

The aim of this study is to clarify the radon behavior in the soil at the waste rock yards of uranium mine. We have developed an apparatus for measuring radon diffusion coefficient in soil under the control of soil temperature. The radon diffusion coefficients changed suddenly around the soil temperature of 0degC. The radon diffusion coefficients in dry soil have little temperature dependency, and were comparable coefficients obtained by empirical formula of Rogers and Nielson. To study the restraint effect of radon exhalation by covering with bentonite on soil, we carried out the measurements and the calculations by using one-dimensional transport model of atmosphere and soil. The decrease of radon exhalation rate was 2.9 Bq m"-"2s"-"1 when soil covered with the bentonite of 5 cm thick. The radon concentrations in snow cover and the radon flux from the snow surface were measured at the waste rock yard in Ningyo-toge Environmental Engineering Center. The simulation ...

Energy Technology Data Exchange (ETDEWEB)

Heat transfer augmentation in narrow rectangular channels in a target system is a very important method to remove high heat flux up to 12 MW/m{sup 2} generated at target plates of a high-intensity proton accelerator of 1.5 GeV and 1 mA with a proton beam power of 1.5 MW. In this report, heat transfer coefficients and friction factors in narrow rectangular channels with one-sided rib-roughened surface were evaluated for fully developed flows in the range of the Reynolds number from 6,000 to 1,00,000; the rib pitch-to-height ratios (p/k) were 10,20 and 30; the rib height-to-equivalent diameter ratios (k/De) were 0.025, 0.03 and 0.1 by means of previous existing experimental correlations. The rib-roughened surface augmented heat transfer coefficients approximately 4 times higher than the smooth surface at Re=10,000, p/k=10 and k/De=0.1; friction factors increase around 22 times higher. In this case, higher heat flux up to 12 ...

International Nuclear Information System (INIS)

Single pellets (of approximately 70 g each) of irradiated lithium aluminate target from N-Reactor test PT-57 were used in a series of experiments to determine the extent to which the product tritium can be recovered by (a) vacuum outgassing of the target (thermal extraction-TX) and (b) in-vacuo chemical dissolution of the target in molten sodium tetraborate (flux extraction-FX). Five TX runs and seven FX runs were made. Thirty-five percent of the tritium was recovered in a form non-condensable at -196"0C. The remainder was recovered in a condensable form (as T_2O, HTO, etc.). Post-extraction analysis of the melt from the seven flux extractions showed that a maximum of 2 percent of the original amount of tritium remained and that target dissolution was essentially complete in 12 hours. Flux extraction of two pellets which had been subjected to thermal extraction showed less than 0.4 percent of the original amount of tritium ...

CERN Document Server

This thesis is divided up into five chapters as outlined below. Chapter 1 gives the background to the techniques used in this thesis including X-ray structure determination and ab initio methods. An overview of some recent studies using ab initio methods to study transition metal complexes is also given. Chapter 2 investigates structural trans influence in a number of transition metal and p-block complexes. The database and ab initio studies showed that the classical trans influence model based on Pt(II) chemistry does not always hold. For some systems (eg. d sup 1 sup 0 s sup 0 for Sb sup V and Sn sup I sup V) the cis influence is of similar magnitude to the trans influence. For other systems (d sup 0), the trans influence is not as powerful as usually assumed. Chapter 3 is an investigation into the bridging chloride unit. A database study was performed on three systems (M-CI-M', M-CI...H and M-CI...Li/Na/K). Reaction ...

Energy Technology Data Exchange (ETDEWEB)

This invention is a manufacturing method of a metal-hydrogen alkali battery cell consisting of a positive electrode of metal oxides, alkaline electrolyte solution and a separator containing an amide-radical, wherein the above treating solution is aqueous solution of KOH (or NaOH) which is heated at least at 40 centigrade and the separator is first immersiion-treated and then water-washed and dried. The amide-radical-containing separaator uses a nylon non-woven fabrics. Average molecular weight of nylon 66 is 12,000 - 20,000. In this invention, in order to improve the storage ability and the cycle characteristics which are caused by corrosion of a separator which takes place in the cell after its assembly, the separator is immersed in a hot alkali in order to obtain a non-woven fabric of nylon 66 consisting of alkali-stable high molecular weight portion, which is assembled into a battery. By this, the dissolving of the non-woven fabric and the ...

Energy Technology Data Exchange (ETDEWEB)

This presentation describes a method for separating {sup 14}C-hexose from {sup 14}C-sucrose in extracts of plant tissue. Portions of ethanol extracts are treated with activated charcoal in microcentrifuge tubes. Aliquots are removed, ethanol evaporated and replaced with reaction mixture that phosphorylates hexose (HEPPS, K{sub 2}HPO{sub 4}, Mg(C{sub 2}H{sub 3}O{sub 2}){sub 2}, ovalbumen, Na{sub 2}ATP, yeast hexokinase). After a time course, the hexokinase reaction is stopped (slowed considerably) to minimize effects of contamination enzyme activities. The stopping agent used is lyxose, a nonphosphorylable analogue of glucose. The strong anionic charge of phosphate introduced through the hexokinase action results in binding (> 95%) of hexose-phosphate to anion-exchange resin. Sucrose remains unbound (> 95%) in solution. This batch ion-exchange is performed in microcentrifuge tubes to allow many samples to be processed simultaneously. ...

Energy Technology Data Exchange (ETDEWEB)

The crystallization of calcium sulfate from aqueous solutions with NaCl is both geological and industrial interest because NaCl is the dominant solute in natural brines and many industrial fluids. Induction periods for the nucleation of calcium sulfate dihydrate were experimentally determined as a function of supersaturation in NaCl solutions from 0 to 6 m at 25 C and in 3.0-m NaCl solutions at temperatures from 25 to 90 C. Using classic nucleation theory, the interfacial tension between gypsum and 3.0-m NaCl solution was estimated to be about 39 mJ/m[sup 2] at 25 C and increases with increasing temperature (to 63 mJ/m[sup 2] at 90 C). It was observed that the induction period decreases with increasing NaCl concentrations up to 3 m and then starts to increase slightly at a given temperature and saturation state. The electrolyte effect on nucleation was ...

Energy Technology Data Exchange (ETDEWEB)

MoO[sub 3] as well as WO[sub 3] react with an excess of NaNH[sub 2] in autoclaves at temperatures ranging from 250 C to 750 C to yield - in contrast to Ta[sub 2]O[sub 5] backslash lbrackvertical stroke 1 backslash rbrackvertical stroke - oxonitridometallates of general composition Na[sub 4]MX[sub 4] and other products like Na[sub 5]WO[sub 4]N backslash lbrackvertical stroke 2 backslash rbrackvertical stroke . The compounds decompose in moist air within minutes to Na[sub 2]WO[sub 4], Na[sub 2]MoO[sub 4] and Na[sub 2]MoO[sub 4].xH[sub 2]O, respectively. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The effects of thiosulfate ion and solution pH on pitting corrosion of Alloy 690 in chloride solution were explored. Potentiodynamic polarization measurements were conducted to evaluate pitting corrosion susceptibility of Alloy 690 in these environments. The results showed that pitting corrosion occurred in the mill-annealed (1050 deg. C/5min) Alloy 690 in 1 wt% NaCl solution but not in 0.1 M Na{sub 2}S{sub 2}O{sub 3} solution. The value of pitting nucleation potential (E{sub np}) determined in 1 wt% NaCl solution (without Na{sub 2}S{sub 2}O{sub 3} ) increased with increasing solution pH value in the range of 2-10. The addition of Na{sub 2}S{sub 2}O{sub 3} to 1 wt% NaCl solution greatly affected the pitting corrosion behavior, which was dependent on concentration. The preformed nickel sulfide surface film due to the presence of Na{sub ...

UK PubMed Central (United Kingdom)

Searching for the structural requirements improving the potency and the stereoselectivity of Na⁺ channel blockers as antimyotonic agents, new...Full Text Available

International Nuclear Information System (INIS)

Information is presented concerning solute concentration in a porous layer; solute concentration in a packed crevice; corrosion of a packed carbon steel crevice in NaCl-O"2 solutions; and effect of copper on corrosion in NaCl-O"2 solutions.

International Nuclear Information System (INIS)

The sodium- and potassium-dependent adenosine triphosphatase (Na+,K(+)-ATPase) maintains the transmembrane Na+ gradient to which is coupled all active cellular transport systems. The R and S alleles of the gene encoding the Na+,K(+)-ATPase alpha 1 subunit isoform were identified in Dahl salt-resistant (DR) and Dahl salt-sensitive (DS) rats, respectively. Characterization of the S allele-specific Na+,K(+)-ATPase alpha 1 complementary DNA identified a leucine substitution of glutamine at position 276. This mutation alters the hydropathy profile of a region in proximity to T3(Na), the trypsin-sensitive site that is only detected in the presence of Na+. This mutation causes a decrease in the rubidium-86 influx of S allele-specific sodium pumps, thus marking a domain in the Na+,K(+)-ATPase alpha subunit important for K+ transport, and supporting ...

Energy Technology Data Exchange (ETDEWEB)

The use of europium as a local structural probe allows the various phases appearing in the NaCaPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ and NaSrPO/sub 4/-Na/sub 3/Eu(PO/sub 4/)/sub 2/ systems to be detected. The broadening of the europium emission lines in going from the calcium to the strontium phases illustrates the ease of displacement of the PO/sub 4/ groups.

Energy Technology Data Exchange (ETDEWEB)

SO/sub 2/ adsorption onto faujasite-type zeolites (Na-X, Na-Y) was investigated by combined UV and IR spectroscopy. Formation of chemisorbed HSO/sub 3//sup -/ species, indicated by a UV band around 215 nm and a low-frequency IR band at 1240 cm/sup -1/, was shown to depend significantly upon the presence of water. Differences in the behavior of Na-X and Na-Y were discussed in terms of different site populations.

CERN Document Server

The Ludwig-Soret effect, the migration of a species due to a temperature gradient, has been extensively studied without a complete picture of its cause emerging. Here we investigate the dynamics of DNA and spherical particles sub jected to a thermal gradient using a combination of Brownian dynamics and the lattice Boltzmann method. We observe that the DNA molecules will migrate to colder regions of the channel, an observation also made in the experiments of Duhr, et al[1]. In fact, the thermal diffusion coefficient found agrees quantitatively with the experimental value. We also observe that the thermal diffusion coefficient decreases as the radius of the studied spherical particles increases. Furthermore, we observe that the thermal fluctuations-fluid momentum flux coupling induces a gradient in the stress which leads to thermal migration in both systems.

International Nuclear Information System (INIS)

The authors describe a new method which makes it possible to determine the radial distribution of the diffuse component of galactic gamma rays outside the solar circle. They use the observation that a good correlation exists between gamma-ray intensities and total column densities of the local interstellar gas and that the fractional column density of H_2<0.1 HI outside the solar circle. Thus the gamma-ray intensities are shown to be proportional to N(HI). The authors use the kinematics of the HI to determine the distances from which various fractions of the emission originate in the second and third galactic quadrants. Preliminary results of our analysis show that a significant flux of gamma rays originates from distances as large as 18 kpc from the galactic centre. (Auth.).

Science.gov (United States)

A series of experiments is to be made during the acceptance test program of the Fast Flux Test Facility (FFTF) to measure the gamma ray characteristics of the Fast Test Reactor (FTR) and to establish the performance characteristics of the reactor shield. These measurements are a part of the FFTF Reactor Characterization Program (RCP). Detailed plans have been developed for these experiments. During the initial phase of the Characteristics Program, which will be carried out in the In-Reactor Thimble (IRT), both active and passive measurement methods will be employed to obtain as much information concerning the gamma ray environment as is practical. More limited active gamma ray measurements also will be made in the Vibration Open Test Assembly (VOTA).

Energy Technology Data Exchange (ETDEWEB)

The Interim Examination and Maintenance (IEM) Cell is located within the Fast Flux Test Facility (FFTF) Reactor Containment Building. This cell is a complex vertical hot cell whose purpose is to process reactor experiments and to perform maintenance on reactor and refueling components. Because access to this very complex cell is limited, a mock-up called the IEM Training Facility (IEMTF) has been developed. The IEMTF provides the IEM cell with many valuable benefits. Four of these benefits are: (1) development of alternate processing methods; (2) hands-on evaluation of equipment problems; (3) a ready source of verified parts, and (4) training facilities for IEM Cell technicians.

Energy Technology Data Exchange (ETDEWEB)

Neutron Coded Aperture Imaging is a nondestructive imaging technique that utilizes neutrons scattered from an object through specially designed apertures. Coded Aperture Imaging is an alternative technique to Computed Tomography for three-dimensional imaging. Coded Aperture Imaging has the advantage that all of the three-dimensional information is contained in a single image, whereas Computed Tomography requires several images or projections. This technique has been implemented by other using photographic film as an image recording medium and optical reconstruction or decoding of the images. In this work, the possibility of using a real-time neutron video camera to record the images, followed by digital decoding methodology has been investigated. Because only a small fraction of the neutrons incident on the object are scattered to the neutron camera, a new neutron beamport facility, with a larger neutron flux (7.3 x 10[sup 7] n/cm[sup 2]/s) than the previous ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

The thermal-neutron capture cross section (#sigma#_0_,_g) and the resonance integral (I_0_,_g) leading to the ground state of "2"4"2Am were measured by an activation method for neutron capture by "2"4"1Am. A method with gadolinium, which was similar to the cadmium difference method, was used to measure the cross section #sigma#_0_,_g with attention to resonances of "2"4"1Am. Americium chloride samples containing "2"4"1Am radioisotope were irradiated for 68 h in the long-irradiation plug of the Kyoto University Research Reactor, KUR. Wires of Co/Al and Au/Al alloys were used as monitors to determine thermal-neutron fluxes and epithermal Westcott's indexes at the irradiation positions. An #alpha#-ray spectrometer was used to measure the activity ratios of "2"4"2Cm to "2"4"1Am. On the basis of Westcott's convention, the #sigma#_0_,_g and I_0_,_g values were determined as 628#+-#22 b and 3.5#+-#0.3 kb, ...

Energy Technology Data Exchange (ETDEWEB)

The energy-integrated reaction cross-sections of several neutron-rich nuclei ({sup 17-22}N, {sup 19-24}O, {sup 21-27}F, {sup 23-30}Ne, {sup 26-33}Na, {sup 28-35}Mg, {sup 31-38}Al, {sup 33-40}Si, {sup 36-42}P, {sup 39-44}S, {sup 42-45}Cl, {sup 45,46}Ar), measured at intermediate energy (30-65 A-bar MeV), via direct method, are presented. Silicon detectors have been used as the active target as well as for particles identification. The reduced strong absorption radii r{sub 0}{sup 2} are extracted and compared to the data available from the literature. New measurements for 19 nuclei ({sup 27}F, {sup 27,30}Ne, {sup 33}Na, {sup 28,34-35}Mg, {sup 36-38}Al, {sup 38-40}Si, {sup 41-42}P, {sup 42-44}S, {sup 45}Cl) are revealed. From the study of the isospin dependence of the reduced strong absorption radius, a new quadratic parameterisation of the nuclear radii in the closed shell regions N=8 and N=28, is proposed. According to this ...

Energy Technology Data Exchange (ETDEWEB)

The pharmacological properties of medicinal plants have been related to the presence of organic compounds, however elements are also known to have an important participation in the active compounds constitution process. In this study, instrumental neutron activation analysis (INAA) was applied to determine elements in leaves of Casearia obliqua medicinal plant collected at two different locations in the Atlantic Forest, Brazil, SP. Soil samples collected from where this plant was grown were also analyzed in order to verify if there is a correlation between the elements present in soils and plant leaves. Br, Ca, Cl, Co, Cr, Cs, Fe, K, La, Mn, Na, Rb, Sb, Sc and Zn were determined in C. obliqua leaves and the elements As, Ca, Ce, Eu, Fe, Hf, La, Lu, Nd, Rb, Sc, Sm, Tb, Th, U and Zn in soils. Soil samples collected from two different locations presented similar concentrations for most elements. Likewise, C. obliqua leaves collected from the two locations presented ...

International Nuclear Information System (INIS)

The principal mathematical tools frequently available for calculations in Nuclear Engineering, including coupled neutron-gamma radiations shielding problems, involve the full Transport Theory or the Monte Carlo techniques. The Multigroup Albedo Method applied to shieldings is characterized by following the radiations through distinct layers of materials, allowing the determination of the neutron and gamma fractions reflected from, transmitted through and absorbed in the irradiated media when a neutronic stream hits the first layer of material, independently of flux calculations. Then, the method is a complementary tool of great didactic value due to its clarity and simplicity in solving neutron and/or gamma shielding problems. The outstanding results achieved in previous works motivated the elaboration and the development of this study that is presented in this dissertation. The radiation balance resulting from the ...

British Library Electronic Table of Contents (United Kingdom)

Integrative and firing properties are important characteristics of neuronal circuits and these responses are determined in large part by the repertoire of ion channels they express, which can vary considerably between cell types. Recently, a new mode of operation of voltage dependent sodium channels has been described that generates a so-called resurgent Na^+ current. Accumulating evidence suggests resurgent Na current participates in the generation of sub-threshold inward Na^+ current causing membrane depolarization which provides the necessary drive to fire high-frequency action potentials. Recent studies indicate that resurgent Na^+ current could be a more widespread feature than previously thought.

International Nuclear Information System (INIS)

Removal of radioactive ions was studied from low and medium level radioactive waste solutions by electrodialysis using ion exchange membranes. The test solutions contained "1"3"7Cs"+, "1"0"6Ru"3"+ or fission products (F.P.) as active ions and NaCl, Na_2SO_4 or Ca(NO_3)_2 as inactive coexisting salts. The decontamination factor of the active ions was in the order: "1"3"7Cs"+ (greater than 99%) > "9"0Sr"2"+ > F.P. > "1"0"6Ru"3"+. The dialysis time required to attain the saturation was the shortest for monovalent cations K"+, Cs"+ and Na"+, intermediate for divalent cation Sr"2"+, and the longest for trivalent cation Ru"3"+. The ratio of the decontamination factor of an active ion eta sub( a) to the desalination factor of an inactive ion eta sub( b) was nearly equal to unity for "2"4Na, "4"2K, "1"3"7Cs and "9"0Sr. On the other hand, the apparent selective permeability of an active ion (A"+) ...

Science.gov (United States)

A novel sorbent for SO2 removal has been investigated. The sorbent is obtained by conventional incipient wetness impregnation of abandoned biomaterials (straw or dried leaves) with an aqueous solution of Na2CO3. A material with the composition 80 wt % Na2CO3/straw shows a desulfurization activity which is both higher and faster than that of the reference sample Na2CO3/gamma-Al2O3. The breakthrough and stoichiometric SO2 adsorption efficiencies for 80 wt % Na2CO3/straw reach 48.9% and 80.6%, respectively, at a temperature of 80 degrees C. The adsorption efficiencies are almost constant in the temperature range 70 to 300 degrees C. According to IR and XPS analysis the main products observed on the spent sorbent are sulfite below 150 degrees C and sulfate at 300 degrees C. The Na2CO3 in 80 wt % Na2CO3/straw can potentially be recycled by the oxidation of the straw ...

Energy Technology Data Exchange (ETDEWEB)

The important amount of hydration water in the ulexite (NaCaN{sub 5}O{sub 9}.8H{sub 2}O), allows using calcination methods to increase its B{sub 2}O{sub 3} content. This paper analyses the thermal decomposition reaction of a preconcentrated ulexite through weight loss measurements, which occur during the heating of samples until 1000 degree centigree, Determinations of heat content at each temperature were made using an isoperibol calorimeter. The mean specific heat was calculated from these values, and its dependence on temperature was determined. The maximum weight loss was about 32.5% and the specific heat obtained was 1,13 kJ/kg 0 C for solid samples and 1,38 kJ/kg''0 C for fluid samples. The results are useful for the design of the industrial process, in order to determine the thermal requirements for heating calcined ulexite, and to obtain smelted ulexite. (Author) 19 refs.

International Nuclear Information System (INIS)

This work presents a comparative study of low-alloy steel nitriding for different possible techniques. Active screen plasma nitriding (ASPN) is a successful surface modification method that has many advantages over the conventional DC plasma nitriding (CPN). The corrosion behavior of 30CrNiMo8 low-alloy steel has been examined using anodic polarization tests in 3.5% NaCl solution under varying conditions of ASPN and CPN processes. The process variables included active screen setup parameters, treatment temperature (550 and 580 deg. C), gas mixture (25/75 and 75/25 of N_2/H_2) and treatment time (5 and 10 h) in 500 Pa pressure. The structure and phases composition of the compound layer was studied by X-ray diffraction (XRD), microhardness tests, optical microscopy and scanning electron microscopy (SEM). It was observed that ASPN treated samples surface enhanced corrosion resistance while the temperature and/or hole size of screen setup ...

Energy Technology Data Exchange (ETDEWEB)

The removal of heavy metal by microbial biomass have been investigated as an alternative to the traditional methods. The removal of the heavy metals copper and iron from discarded lubricating-oil was studied using the biosorbent Sargassum sp. It was chosen a discarded lubricating-oil of a bus fleet from the city of Natal-RN-Brazil. The oil was characterized to determine and quantify the heavy metals present. The effect of biomass protonation was performed in order to increase the removal efficiency of the metals. The equilibrium time between the oil and the biomass was determined. It was found that after 10 hours the equilibrium was reached. It was also studied the influence of biomass quantity. The results showed that the biomass quantity is an important parameter to the efficiency and biosorption capacity. The protonated biomass was shown more efficient to removal of Fe and Cu, removing 37,53% and 31,63% respectively. (author)

Energy Technology Data Exchange (ETDEWEB)

The LiMnO{sub 2} lamellar oxide, obtained by exchange reaction from its sodium homologue {alpha}-NaMnO{sub 2}, has been used as a positive electrode for lithium batteries. After the first electrochemical cycle, the shape of the potential-composition curve changes and indicates a change in the structure. This modification changes imperceptibly at each cycle and after about 40 cycles, a stationary state is reached. Powder spectra refinement using the Rietvelt method shows a migration of manganese ions from the thin sheets towards the inter-sheet space. After a single cycle, 8% of the manganese ions are already present in the lithium site and this rate reaches 13% after 3 cycles. During long cycling, a redistribution of ions and vacancies inside the cfc oxygenated pile leads to a structure very similar to the LiMn{sub 2}O{sub 4} spinel. This structure evolution is to be compared with the one obtained from the orthorhombic variety of LiMnO{sub 2} ...

Energy Technology Data Exchange (ETDEWEB)

This paper presents the experience faced by people who works in PETROBRAS Business Unit (UN-RNCE), located in Rio Grande do Norte Province, Brazil, during the implementation of a pipeline leak detection system. That application involved nine multiphase oil pipelines distributed along several production facilities. Because of the emergency after the leakage that polluted the Guanabara bay and due to the two phases and multi phases pipelines characteristics, the UN-RNCE decided to apply the Pressure Point Analysis (PPA) technology in order to detect leakages. It is a statistical method for leak detection e uses a very simple instrumentation which facilitates the installation and maintenance. However, in order to get the best performance of the system, it is necessary to know thoroughly the whole process and have a fast and reliable SCADA system for long distance communication. Finally it will be shown the test results, the recommendations to expand the system and the ...

Energy Technology Data Exchange (ETDEWEB)

A technique capable of measuring the electron energy fluence spectra in a scattering medium was designed. These measurements were performed by setting a bremsstrahlung conversion target on the surface of a phantom, at an intermediate depth, and at a depth equal to electron mean range. The bremsstrahlung produced by the deceleration of electrons in the target was passed through an air channel in the phantom and passed forward by a pinhole collimator into a Na(Tl) detector. The measured pulse height data were unfolded to correct for the distortion of the spectrometer system by using the FORIST unfolding code. The unfolded bremsstrahlung spectra represent the electron energy fluence spectra convolution with the bremsstrahlung produced in the target. To generate the electron energy fluence spectra, the unfolded bremsstrahlung spectra were deconvoluted by using the MAZE2 unfolding code. CYLTRAN, a coupled electron-photon Monte Carlo transport code, was used to produce ...

International Nuclear Information System (INIS)

Impurities (Ca, Cr, Cu, Fe, K, Mg, Mn, Na, Ni, Ti, Y, Zn and Zr) in sialon powder were determined by the following procedure: A sample (0.5 g) was heated with a mixture of hydrofluoric acid (3 ml) and nitric acid (1 ml) in a Teflon pressure vessel at 170degC for 16 h. The contents of the vessel were transferred into a platinum crucible containing phosphoric acid (4 ml) and heated on a hot plate until the opaque appearance of the content changed to a clear-syrupy fluid. The fluid was diluted to 100 ml with water and used for ICP-AES analysis of all impurity elements except K, which was determined by AAS. It was necessary to match closely the matrix concentrations (H_3PO_4, Al and/or Y) of the standard solutions with those of sialon sample solutions for the determination of impurities because of interferences of the matrix components. This method was successfully applied to the determination of impurities in commercial sialon samples. (author).

International Nuclear Information System (INIS)

The cross sections of "2"0"4Pb(n,2n)"2"0"3Pb and "2"0"6Pb(n, #alpha#)"2"0"3Hg reactions have been measured by using the activation method in the neutron energy range of 13.50-14.81 MeV. Neutron fluence dose was calibrated with the cross sections of "2"7Al(n, #alpha#)"2"4Na reaction and neutron energies were determined by using the cross section ratios of "9"0Zr(n,2n)"8"9"m"+"gZr to "9"3Nb(n,2n)"9"2"mNb reactions. The results obtained are compared with the published data.

Energy Technology Data Exchange (ETDEWEB)

Results from four chemical-equilibrium computer programs, REDEQL.EPAK, GEOCHEM, WATEQF, and SENECA2, have been compared with experimental solubility data for some simple systems of interest with geothermal brines. Seven test cases involving solubilities of CaCO/sub 3/, amorphous SiO/sub 2/, CaSO/sub 4/, and BaSO/sub 4/ at various temperatures from 25 to 300/sup 0/C and in NaCl or HCl solutions of 0 to 4 molal have been examined. Significant differences between calculated results and experimental data occurred in some cases. These differences were traced to inaccuracies in free-energy or equilibrium-constant data and in activity coefficients used by the programs. Although currently available chemical-equilibrium programs can give reasonable results for these calculations, considerable care must be taken in the selection of free-energy data and methods of calculating activity coefficients.

British Library Electronic Table of Contents (United Kingdom)

An extremely sensitive stripping voltammetric procedure for ultra-trace determination of iridium(III) is reported. The method is based on the interfacial accumulation of the iridium(III)-CTAB complex onto the glassy carbon electrode, followed by the catalytic reduction of the adsorbed complex in the presence of bromate. 0.3molL^-^1 acetate buffer pH 4.7+6.9x10^-^2molL^-^1 NaBrO3+2.7x10^-^5molL^-^1 cetyltrimethylammonium bromide (CTAB)+0.2molL^-^1 KCl was employed as the supporting electrolyte. The analytical procedure was verified by the analysis of the standard reference materials: Sea Water BCR-CRM 403 and Fresh Water NIST-SRM 1643d. The accuracy, expressed as relative error e%, was satisfactory, being lower than 6%, while precision as repeatability, expressed as relative standard deviat...

CERN Document Server

We propose a new method to measure the metallicity of Type Ia supernova progenitors using Mn and Cr lines in the X-ray spectra of young supernova remnants. We show that the Mn to Cr mass ratio in Type Ia supernova ejecta is tightly correlated with the initial metallicity of the progenitor, as determined by the neutron excess of the white dwarf material before thermonuclear runaway. We use this correlation, together with the flux of the Cr and Mn Kalpha X-ray lines in the Tycho supernova remnant recently detected by Suzaku (Tamagawa et al. 2008) to derive a metallicity of log(Z) = -1.32 (+0.67,-0.33) for the progenitor of this supernova, which corresponds to log(Z/Zsun)= 0.60 (+0.31,-0.60) according to the latest determination of the solar metallicity by Asplund et al. (2005). The uncertainty in the measurement is large, but metallicities much smaller than the solar value can be confidently discarded. We discuss the implications of this result ...

International Nuclear Information System (INIS)

A method for converting organic iodides to elemental iodine would be advantageous in improving the performance of charcoal filters for the removal of radio iodines from reactor off gases. A photochemical method has been developed. The HAVCHM code was used to establish the relevant process time scales on a complete set of rate equations describing the primary and secondary reactions occurring in a plug-flow reactor containing low levels of elemental iodine and methyl iodide in air, which is irradiated by intense u.v. light. These simulations were used to justify the contraction of the complete set of reactions to the most significant elementary processes. The contracted set of rate equations are then solved analytically to render the concentration-time profiles of methyl iodide, total inorganic iodine and total oxidized organics, consistent with the achievement of a desirable radioiodine decontamination factor. For the short contact times ...

Energy Technology Data Exchange (ETDEWEB)

This report is the first of four volumes that identify and assess the environmental, health, and safety issues involved in using sodium-sulfur (Na/S) battery technology as the energy source in electric and hybrid vehicles that may affect the commercialization of Na/S batteries. This and the other reports on recycling, shipping, and vehicle safety are intended to help the Electric and Hybrid Propulsion Division of the Office of Transportation Technologies in the US Department of Energy (DOE/EHP) determine the direction of its research, development, and demonstration (RD&D) program for Na/S battery technology. The reports review the status of Na/S battery RD&D and identify potential hazards and risks that may require additional research or that may affect the design and use of Na/S batteries. This volume covers cell design and engineering as the basis of safety for ...

International Nuclear Information System (INIS)

In order to assess various core parameters a reference equilibrium core with Low Enriched Uranium (LEU) fuel for Pakistan Research Reactor (PARR-1) was assembled. Due to increased volume of reference core, the average neutron flux reduced as compared to the first higher power operation. To get a higher neutron flux an irradiation facility was created in centre of the reference equilibrium core where the advantage of the neutron flux peaking was taken. Various low power experiments were performed in order to evaluate control rods worth and neutron flux mapping inside the core. The neutron flux inside the central irradiation facility almost doubled. With this arrangement reactor operation time was cut down from 72 hours to 48 hours for the production of the required specific radioactivity. (author)

International Nuclear Information System (INIS)

For the advanced fusion reactor FFHR2 (Force Free Helical Reactor) that has been proposed by NIFS, molten salt Flibe (LiF:BeF2=64:36) breeder blanket system is selected because of Flibe's features such as chemical stability, low-pressure operation and low electric conductivity. The Flibe is however high Prandtl number fluid since it has high viscosity and low thermal conductivity. Therefore its heat transfer performance is low compared with liquid Li or Pb-Li. In addition to heat removal of 1MW/m2 on the first wall, electrolysis of molten salt due to MHD effect will take place under high flow rate condition. This indicates that heat transfer enhancement under low flow rate is essential for the Flibe blanket system. In our laboratory, heat transfer characteristics of molten salt HTS (KNO3:NaNO2:NaNO3=53:40:7), have been evaluated, which is used as a simulant fluid of Flibe from the points of view of Be's toxicity and similar Prandtl number. In ...

Energy Technology Data Exchange (ETDEWEB)

This report provides the results of a JASON review of the technical feasibility of using the Department of Energy`s (DOE`s) Fast Flux Test Facility (FFTF) to generate tritium needed for the enduring United States nuclear weapons stockpile.

UK PubMed Central (United Kingdom)

We analyze transport through conical channels due to the difference in particle concentration on the two sides of the membrane. Because of the detailed balance, fluxes of non-interacting particles...Full Text Available

International Nuclear Information System (INIS)

The sol-gel-immobilized Tris(2,2'-bipyridyl)ruthenium(II) [Ru(bpy)_3 "2"+] electrogenerated chemiluminescence (ECL) sensor was applied to the reversed-phase high-performance liquid chromatography (HPLC) determination of phenothiazine derivatives (promazine, chlorpromazine, triflupromazine, thioridazine, and trifluoperazine) and erythromycin in human urine samples. In this method, Ru(bpy)_3 "2"+ was immobilized in sol-gel-derived titania (TiO_2)-Nafion nanocomposite films coated on a dual platinum electrode. This method eliminates an extra pump needed for the delivery of Ru(bpy)_3 "2"+ reagent into a reaction/observation zone in front of photomultiplier tube because the immobilized-Ru(bpy)_3 "2"+ is recycled on the electrode surface by an applied potential at +1.3 V versus Ag/AgCl (3 M NaCl) reference electrode. The resulting analytical performances such as detection limit, working range, sensitivity, and measurement ...

CERN Document Server

We use the conductimetric method, adequate to electrolytes, to determine the lysozyme charge in lys-water and ternary lys-salt-water systems. We measured also the viscosities for the above binary and ternary systems in the same conditions at pH$=4.5$ and T$=298$ K, measurements that allow us to see any effect of viscosity on cations mobilities and implicitly on the lysozyme charge. The method is illustrated for the lysozyme chloride aqueous solution system at 25$^o$ C, using the data reported here for pH$=4.5$ at 0.15, 0.6, 0.8, 1., 1.5, 2., 2.5, 3., 3.5 mM (mg/mL) lysozyme chloride concentrations. The method was also applied to ternary lys-salt-water systems in the same conditions at pH$=4.5$ and T$=25^o$ C. Ternary conductivities are reported for a mean concentration 0.6 mM of lysozyme chloride in all systems and a mean concentration 0.01, 0.025, 0.05, 0.1, 0.175, 0.2, 0.5, 0.7, 0.9, 1.2, 1.3 and 1.4 M for ...

Energy Technology Data Exchange (ETDEWEB)

The Segmented Rail Phased Induction Motor (SERAPHIM) is a compact, pulsed linear induction motor (LIM) offering a unique capability for very high speed train propulsion. It uses technology developed for the Sandia coilgun, an electromagnetic launcher designed to accelerate projectiles to several kilometers per second. Both aluminum cylinders and plates were accelerated to a kilometer per second (Mach 3) by passing through a sequence of coils which were energized at the appropriate time. Although this technology was developed for ultra-high velocity, it can be readily adapted to train propulsion for which, at sea level, the power required to overcome air resistance limits the operational speed to a more modest 300 mph. Here, the geometry is reversed. The coils are on the vehicle and the ``projectiles`` are fixed along the roadbed. SERAPHIM operates not by embedding flux in a conductor, but by excluding it. In this propulsion scheme, pairs of closely spaced coils on ...

International Nuclear Information System (INIS)

We report here on an experimental system that utilizes ion-selective microelectrodes to measure the electrochemical potential gradients for H"+ and K"+ ions within the unstirred layer near the root surface of both tact 4-day-old corn seedlings and corn root segments. Analysis of the steady state H"+ and K"+ electrochemical potential gradients provided a simultaneous measure of the fluxes crossing a localized region of the root surface. Net K"+ influx values obtained by this method were compared with unidirectional K"+ ("8"6Rb"+) influx kinetic data; at any particular K"+ concentration, similar values were obtained by either technique. The ion-specific microelectrode system was then used to investigate the association between net H"+ efflux and net K"+ influx. Although the computed H"+K"+ stoichiometry is dependent upon the choice of diffusion coefficients, the values obtained were extremely variable, and net K"+ influx rarely appeared to be ...

Energy Technology Data Exchange (ETDEWEB)

Applying a total energy absorption {gamma}-ray detector composed of 12 bricks (5x5 cm{sup 2}, 7.5 cm thick) of Bi{sub 4}Ge{sub 3}O{sub 12}(BGO) scintillators, the absolute measurement of capture cross sections for Au and Sb has been made in an energy region between 0.01 eV and 10 eV using the linac time-of-flight method. Incident thermal neutron flux was absolutely determined by using the BGO detection system with a Sm sample. To extend the neutron flux measurement from the thermal neutron region to higher neutron energy, the {sup 10}B(n, {alpha} {gamma}) reaction was applied. Absolute capture yield for the relevant capture sample was obtained by the saturated capture yield at a large resonance of the sample. Gold was selected to investigate the application of the BGO detection system to the absolute measurement of the capture cross sections, since the {sup 197}Au(n, {gamma}){sup 198}Au reaction cross section is a well ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We write a path-integral expression for the Green function of a advected scalar on a fluid flux. (author)

Science.gov (United States)

analysis of NaMBT in ethylene glycol-water solutions with high accuracy. It reduces analysis time, requires smaller samples, and is able to detect extremely ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

UK PubMed Central (United Kingdom)

ObjectiveNeuralgic amyotrophy (NA) is a distinct clinical syndrome that is characterized by the acute onset of shoulder and arm pain, weakness, and sensory loss. The purpose of this...Full Text Available

International Nuclear Information System (INIS)

... activation analysis aluminium 28 calcium 49 chlorine 38 cotton plants li-drifted

International Nuclear Information System (INIS)

The corrosion behavior of the sputter-deposited amorphous or nanocrystalline W-Nb alloys is studied in 10% NaCl, 0.1 and 1 M NaOH solutions at 24 deg. C, open to air using immersion tests and electrochemical measurements. Niobium metal acts synergistically with tungsten in enhancing the corrosion resistance of the W-Nb alloys so as to show lower corrosion rates than the corrosion rates of the alloy-constituting elements in almost all examined solutions. Corrosion rates of W-Nb alloys are about more than one order of magnitude less than that of the sputter-deposited tungsten and even lower than that of sputter-deposited niobium. The stability of the anodic passive films formed on the W-Nb alloys increase with niobium content.

Science.gov (United States)

Mar 1, 2011 ... analysis of NaMBT in ethylene glycol-water solutions with high accuracy. It reduces analysis time, requires smaller samples, and is able to ...

International Nuclear Information System (INIS)

In this study, a high-resolution characteristic-based finite-volume (FV) method on unstructured grids [Int. J. Numer. Method Eng. 50 (2001) 11; Int. J. Heat Fluid Flow 21 (2000) 432] is extended by a matrix-free implicit dual-time stepping scheme for the numerical simulation of steady and unsteady flow and heat transfer with porous media. The method has been used to study the characteristics of a complex problem: flow and heat transfer in a channel with multiple discrete porous blocks, which was originally proposed by Huang and Vafai [J. Thermophys. Heat Transfer 8 (3) (1994) 563]. In addition, flow and heat transfer in a channel partially or fully filled with porous layers and containing solid protruding blocks with constant heat flux on its lower surface are also investigated in details. Hydrodynamic and heat transfer results are reported for both steady and transient flow cases. In particular, the ...

International Nuclear Information System (INIS)

A real-time neutron radiography facility was constructed including the capability of neutron tomography. The neutron beam was measured for total neutron flux ((1.0 +/- 0.2) x 10"1"1 m/(m"2-sec)), gold cadmium ratio (52 +/- 3) and effective neutron temperature (83"0C +/- 8"0C). The angular divergence or nonparallelism of the neutron beam was measured to be 2.3"0 +/- 0.1"0 thereby providing a means of quantifying the collimator effectiveness. The resolution capabilities of both static film and real-time neutron radiographs were quantified using a Fourier transform algorithm to calculate the modulation transfer function of both types of radiographs. The contrast sensitivity of both types of radiographs. The contrast sensitivity of both types of radiographs was measured as 3.1% for film and 4.0% for real-time radiographs. Two tomography algorithms, the simultaneous iterative reconstruction technique (SIRT) and the convolution method, were ...

CERN Document Server

Aims. We attempt to detect starlight reflected from the hot Jupiter orbiting the main-sequence star Tau Boo, in order to determine the albedo of the planetary atmosphere, the orbital inclination of the planetary system and the exact mass of the planetary companion. Methods. We analyze high-precision, high-resolution spectra, collected over two half nights using UVES at the VLT/UT2, by way of data synthesis. We interpret our data using two different atmospheric models for hot Jupiters. Results. Although a weak candidate signal appears near the most probable radial velocity amplitude, its statistical significance is insufficient for us to claim a detection. However, this feature agrees very well with a completely independently obtained result by another research group, which searched for reflected light from Tau Boo b. As a consequence of the non-detection of reflected light, we place upper limits to the planet-to-star flux ratio at the 99.9% ...

Energy Technology Data Exchange (ETDEWEB)

In this paper, the state-of-the-art ultrasonic and magnetic measuring techniques developed at Kawasaki Steel and used in the production process of steel sheets are described. Representative examples shown here are as follows: (1) Magnetic flux leakage testing system for the detection of nonmetallic inclusions, (2) Nondestructive orientation measurement for secondary re-crystallized grains in grain-oriented electrical steel by ultrasonic interferometry, (3) Immersion testing method for the detection of nonmetallic inclusions, (4) Surface wave probe for the detection of surface flaws in rolls used in rolling mills. Developments of these techniques and their applications to actual steel sheets production processes have contributed to advance in technologies for quality assurance and control. With the help of these techniques, steel sheet products with advanced and uniform properties are being continuously produced to meet customers' ...

Energy Technology Data Exchange (ETDEWEB)

By using this doping method, silicon semiconductors with extremely uniform dopant distributions can be produced, and this is the dominant advantage of NTD compared with a conventional chemical doping. Good uniformity of a dopant concentration is usually required for high power applications such as thyristor (SCR), IGBT, IGCT and GTO and for special sensors. Achieving an accurate neutron fluence corresponding to a target resistivity as well as a uniform irradiation is the prime target of a neutron irradiation for NTD. Generally, in order to reach an accurate neutron fluence, a real time neutron flux is monitored by a neutron detector such as a Self-powered Neutron Detector(SPND). And, after an irradiation, the total irradiation fluence is confirmed by measuring the absolute activity of a neutron activation sample that has been irradiated with a silicon ingot, and thus the SPND can be properly calibrated. Excellent irradiation uniformity and a ...

CERN Document Server

We review results from general relativistic axisymmetric magnetohydrodynamic simulations of accretion in Sgr A*. We use general relativistic radiative transfer methods and to produce a broad band (from millimeter to gamma-rays) spectrum. Using a ray tracing scheme we also model images of Sgr A* and compare the size of image to the VLBI observations at 230 GHz. We perform a parameter survey and study radiative properties of the flow models for various black hole spins, ion to electron temperature ratios, and inclinations. We scale our models to reconstruct the flux and the spectral slope around 230 GHz. The combination of Monte Carlo spectral energy distribution calculations and 230 GHz image modeling constrains the parameter space of the numerical models. Our models suggest rather high black hole spin ($a_*\\approx 0.9$), electron temperatures close to the ion temperature ($T_i/T_e \\sim 3$) and high inclination angles ($i \\approx 90 \\deg$).

Science.gov (United States)

Summaries are presented for those research contracts which expired between December 31, 1960 and December 31, 1981. Topics covered include: factors controlling distribution of fission products in biosphere, non-destructive methods of evaluating the U/sup 235/ and Pu content of irradiated fuel elements, studies of contamination in local marine resources, tracer studies of anemia, non-destructive analysis of irradiated fuel elements using a flux integrating monitor, mechanism of proteolysis of I/sup 131/-labeled fibrinogen, radiosensitivity of spermatogonia of Drosophila melel elements by gamma scanning, uptake and loss of radioactive material by marine bacteria, factors which influence the movement of radioactive strontium from soils to plants, biological concentration of fission products in mollusks from water, decay scheme of Tl/sup 210/, calcium balance in metabolic bone disease, development of radioactive drugs ...

International Nuclear Information System (INIS)

The utilization of 14.6-min "1"0"1Mo and 25-min "1"3"1Te for the determination of molybdenum and tellurium in biological materials by neutron activation analysis is described for the first time. Radioisotopes were separated from the samples activated in a thermal neutron flux of about 10"1"4 n cm"-"2s"-"1. The radiochemical procedure for molybdenum involves extraction of Mo"6"+ from 6 M HCl into diethylether, re-extraction into water, precipitation as oxinate, and measurement of the gamma activity of "1"0"1Tc. The tellurium was separated by reduction to the element with SO_2 in 3 M HCl, dissolution in HNO_3, and reprecipitation as the element for the measurement of radioactivity. The sensitivity was estimated at ca. 10 ng at the level of confidence of 95%. The methods were tested by analyzing NBS-standard Bovine Liver and Orchard Leaves for molybdenum; the concentrations found were 3.2 +- 0.1 #mu#g g"-"1 and 300 +- 60 ng g"-"1, respectively. ...

Energy Technology Data Exchange (ETDEWEB)

The US Department of Energy (DOE) sponsors an extensive research program to improve the methods, dosimeters, and instruments available to DOE facilities for measuring neutron dose and assessing its effects on the work force. The Total Dose Meter was recently developed for measuring in real time the adsorbed dose of mixed neutron and gamma radiation and for calculating the dose equivalent. The Field Neutron Spectrometer was developed to provide a portable instrument for determining neutron spectra in the workplace for flux-to-dose equivalent conversion and quality factor calculation. The Combination Thermoluminescence/Track Etch Dosimeter (TLD/TED) was developed to extend the effective neutron energy range of the conventional TLDs to improve detection of fast-energy neutrons. An Optically Stimulated Luminescence Dosimeter is presently being developed for application to gamma, neutron, and beta radiation. An Effective Dose Equivalent System is ...

International Nuclear Information System (INIS)

With the objective to improve the reactor physics calculation on a 2D and 3D nuclear reactor via the Diffusion Equation, an adaptive automatic finite element remeshing method, based on the elementary area (2D) or volume (3D) constraints, has been developed. The adaptive remeshing technique, guided by a posteriori error estimator, makes use of two external mesh generator programs: Triangle and TetGen. The use of these free external finite element mesh generators and an adaptive remeshing technique based on the current field continuity show that they are powerful tools to improve the neutron flux distribution calculation and by consequence the power solution of the reactor core even though they have a minor influence on the critical coefficient of the calculated reactor core examples. Two numerical examples are presented: the 2D IAEA reactor core numerical benchmark and the 3D model of the Argonauta research reactor, built in Brasil. (author)

International Nuclear Information System (INIS)

The Fast Flux Test Facility (FFTF) features a three-loop, sodium-cooled 400 MWt mixed oxide fueled reactor designed for the irradiation testing of fuels and materials for use in liquid metal cooled fast reactors. To establish the ultimate capability of a particular fuel design and thereby generate information that will lead to improvements, many of the fuel irradiations are continued until a loss of cladding integrity (failure) occurs. When the cladding fails, fission gas escapes from the fuel pin and enters the reactor cover gas system. If the cladding failure permits the primary sodium to come in contact with the fuel, recoil fission products can enter the sodium. The presence of recoil fission products in the sodium can be detected by monitoring for the presence of delayed neutrons in the coolant. It is the present philosophy to not operate FFTF when a failure has occurred that permits fission fragments to enter the sodium. Thus, it is important that the ...

International Nuclear Information System (INIS)

A new two-phase friction multiplier correlation has been developed to predict the pressure profile in two-phase flow with heat addition. The main difference from other pressure drop prediction routines is that in addition to the effect of quality, the effects of system pressure, heat and mass flux on the two-phase multiplier are included. The inception of two-phase flow is defined to occur at the onset of significant void in the subcooled boiling regime instead of the boundary between negative and positive thermodynamic equilibrium quality. Pressure drop data from an experiment with a fully segmented 6-metre long, 37-element fuel string were used to optimize the constants and exponents of this correlation for the friction multiplier. This pressure drop prediction technique was shown to successfully predict the measured pressure profiles. The more than one hundred overall pressure drop data were predicted with an RMS error of 5.4 percent. The pressure drop measured ...

CERN Document Server

Recent observations of a large excess of cosmic-ray positrons at high energies have raised a lot of interest in leptonic decay modes of dark matter particles. Nevertheless, dark matter particles in the Milky Way halo could also decay hadronically, producing not only a flux of antiprotons but also a flux of antideuterons. We show that for certain choices of parameters the antideuteron flux from dark matter decay can be much larger than the purely secondary flux from spallation of cosmic rays on the interstellar medium, while the total antiproton flux remains consistent with present observations. We show that if the dark matter particle is sufficiently light, the antideuteron flux from dark matter decay could even be within the reach of planned experiments such as AMS-02 or GAPS. Furthermore, we discuss the prospects to observe the antideuteron ...

International Nuclear Information System (INIS)

A simple and rapid method is described for the determination of major and trace elements in rock and sediment samples by wavelength dispersive XRF. Sample measured were made from cellulose powder pressed into 4 cm diameter aluminium ring 0.4 t cm"-"2, and then 1 g of powdered sample (0.08 g cm"-"2) was placed on the disk and repressed at 1.6 t cm"-"2. X-ray measurements were performed for total XRF intensity (I_p) at the characteristic line of each element and background intensity (I_b) in vicinity of the line. The correction of matrix effect was achieved by X-ray intensity ratio of peak to background for each element. Eight standard rock samples from Geological Survey of Japan were used as standard materials, and linear calibration curves were obtained by the plot of I_p - I_b vs. concentration for Ca, Na and Pb and by the plot of I_p/I_b ratio vs. concentration for Si, Fe, Ti, K, P, Cl, Cr, Mn, Ni, Cu, Zn, Pb, Sr and Ba, respectively. The ...

Energy Technology Data Exchange (ETDEWEB)

To evaluate a dose conversion factor from the `Working Level of Month` (WLM) of radon to the absorbed dose (mGy), the quality of radon and its progeny was assessed, and exposures controlled for each deposition region were planed as follows: 1) exposure of radon gas to the entire respiratory tract, 2) exposure of `unattached` fractions to the upper respiratory tract, 3) exposure of `attached` fractions onto ultrafine particles to the deep lung, 4) exposure of `attached` fractions onto fine particles to the lower respiratory tract, 5) exposure of `attached` fractions onto coarse particles to the upper respiratory tract. In this preliminary study, a prototype exposure system of radon and its progeny for small rodents was designed. A whole body exposure chamber with a volume of about 0.5 m{sup 3} was used, which it held 20 rats. The aging and mixing chamber separated by the exposure chamber had a volume of about 1 m{sup 3}. As career aerosols of radon progeny, carnauba wax aerosols as ...

International Nuclear Information System (INIS)

Phenomenological accountancy of quanta-electrodynamic corrections by means of introduction into multielectron theory of short-term potential, the parameters whereof are calibrated in such a way that provides for correct reproduction of the Lamb shift of the 1s-orbital energy for a correspondingly selected effective charge is developed by example of d-line of Na-like multicharged ions.

British Library Electronic Table of Contents (United Kingdom)

The catalytic performance of alkaline-treated zeolite H-ZSM-5 in the conversion of methanol to gasoline has been studied. After treatment with 0.20M NaOH, the total conversion capacity increased by a factor of 3.3, and the selectivity towards the gasoline fraction increased by a factor of 1.7. Physical characterization indicated the formation of mesopores and improved crystallinity.

Energy Technology Data Exchange (ETDEWEB)

The gamma-ray spectrum following neutron capture on /sup 87/Sr was measured at 3 neutron energies: E/sub n/ = thermal, 2 keV, and 24 keV. Gamma rays were detected in a three-crystal Ge(Li)-NaI-NaI pair spectrometer. Gamma-ray intensities deduced from these spectra by spectral unfolding are presented.

UK PubMed Central (United Kingdom)

Rapidly developing changes in the short-circuiting current (Isc), conductance (G), and potential (PD) of turtle bladders in Na-rich or Na-free media are seen after the mucosal addition, at 10 nM, of...Full Text Available

International Nuclear Information System (INIS)

Effect of hydroxide nature, concentration and temperature on corrosion resistance of domestic steels and alloys to hot NaOH, KOH, LiOH solutions is considered. It is ascertained that by corrosion growth in relation to stainless steels and nickel alloys, the hydroxides are placed in the following sequence: LiOHNaOH. Hydroxide solution concentration and temperature regions in which stainless steel and nickel alloy tendency to cracking is manifested, are determined. 12 refs., 12 figs.

Energy Technology Data Exchange (ETDEWEB)

Chemical phase identifications of complex, multilayered corrosion products formed on Fe-Ni-Cr alloys immersed in molten NaNO/sub 3/-KNO/sub 3/ and LiNO/sub 3/-NaNO/sub 3/-KNO/sub 3/ were obtained by X-ray diffraction analysis. Diffraction analyses performed after successive material removal steps provided depth profiles of corrosion products and identified the dominant phases as NaFeO/sub 2/, Fe/sub 3/O/sub 4/, and Cr/sub 2/O/sub 3/ for Alloy 800 and 316SS after immersion in NaNO/sub 3/-KNO/sub 3/. In LiNO/sub 3/-NaNO/sub 3/-KNO/sub 3/, the major corrosion products identified on Alloy 800 were LiFeO/sub 2/, Fe/sub 3/O/sub 4/, and Cr/sub 2/O/sub 3/. X-ray diffraction results were supplemented by electron microprobe analyses that revealed the solid solution nature of several of the oxide phases.

British Library Electronic Table of Contents (United Kingdom)

Soils of arid regions of Central Asia contain salts of different types that may differentially affect seed germination and plant development. We studied effect of NaCl, Na2SO4, 2NaCl + KCl + CaCl2 and 2Na2SO4+K2SO4+MgSO4 on germination of Kochia prostrata and Kochia scoparia seeds under a range of concentrations from 0.5 to 5% and at two constant temperature regimes +22 degrees C and +6 degrees C. The observed salt tolerance limit of germination at constant temperature +22 degrees C for both species was 5-6%, while at low temperature (+6 degrees C) this limit was 2%. The salt tolerance of young plants (before flowering) was 3% for NaCl. Low concentrations of sulfuric and mixed salts had a stimulating effect on seed germination in K. prostrata. Despite similarity of salt-tolerance limits...

Science.gov (United States)

Atmospheric and ionospheric perturbations associated with the acoustic-gravity waves (AGW) with typical frequencies of a few hertz -millihertz are considered. These events may be caused by the influence from space and atmosphere as well as by oscillations of the Earth surface and other near-surface phenomena. The surface sources include long-period oscillations of the Earth's surface, earthquakes, explosions, thermal heating, seisches and tsunami waves. The wavelike phenomena manifest themself as travelling disturbances of air (in the atmosphere) and of electron density (in the ionosphere). Travelling ionospheric disturbances (TIDs) are well detected by radio physical methods. AGW generation by near-surface sources is modeled by the numerical solution of the equation of geophysical fluid dynamics for different sources in two-dimensional non-linear dissipative compressible atmosphere. The numerical calculations are based on the FCT (Flux ...

Energy Technology Data Exchange (ETDEWEB)

A technique involving shifting of core fuel loadings was investigated as a method for reducing the neutron flux at points of high damage accumulation in the pressure vessel wall of a light water reactor. Calculations were run for six types of commercial generic PWR. Information is provided on the progress being made to develop and apply the Solid State Track Recorder (SSTR) method for in-situ in- and ex-vessel measurements of neutron exposure parameter values, such as fluence (E > 1.0 MeV) and dpa in iron. A new technique of quantitative track counting, the Buffon needle method, is advanced. It is based on random sampling of the SSTR surface. A desensitized etching technique was developed that resulted in an excellent differential energy response for alpha particles in the 3- to 14-MeV energy range. The optical efficiency of Muscovite mica for manual fission track counting is being redetermined to ...

International Nuclear Information System (INIS)