British Library Electronic Table of Contents (United Kingdom)

In this article a methodology is presented for studying the influence of the biomass moisture content and the biomass/air ratio on the producer gas composition and on the chemiluminescent emissions during the combustion process. Firstly, a mathematical model based on the thermo-chemical processes inside the gasifier is used to predict the composition of the producer gas as a mixture of CO, CO2, H2, N2, CH4 and H2O gases. Secondly, the predicted composition is introduced into a constant volume combustion bomb (CVCB), which simulates the typical conditions inside the combustion chamber of an internal combustion engine, in order to characterize its combustion under gasoline-type conditions through the instantaneous pressure and the detection of the spontaneous luminous radiation (chemilumines...

Energy Technology Data Exchange (ETDEWEB)

We report the performance of a commercial recuperated micro gas turbine on biomass producer gas and mixtures of biomass producer gas with natural gas. The biomass producer gas, obtained by gasification at 850{sup o}C with air at atmospheric pressure, contains about 7% H2, 17% CO, 15% CO2, 4% CH4, 2% other hydrocarbons, 2% H2O, and a balance of N2 and Ar from air. It has a net heating value of about 6 MJ/(Nm{sup 3}). The micro gas turbine delivers full power (30 kW{sub e}) on gas mixtures with a net heating value of at least 15 MJ/(Nm{sup 3}). For gas of lower heating value, the maximum fuel gas flow allowed by the fuel control unit limits the attainable power. At reduced power, the lower limit for stable operation is a net heating value of about 8 MJ/(Nm{sup 3}). The gross efficiency of the micro gas turbine depends on the output power but not on the gas heating ...

Energy Technology Data Exchange (ETDEWEB)

Three typical Japanese coals of non-coking coal, coking coal and anthracite were heat-treated with KOH, and change in their pore structure was examined by absorption of N2, X-ray diffraction and TEM observation. In addition, the relation between a coal rank and pore structure was also studied by absorption experiment of N2. In experiment, the mixture of coal and KOH in a nickel holder was heat-treated in N2 gas flow at heating rate of 2{degree}C/min, and held at a fixed temperature for one hour. To clarify the pore structure, N2 absorption isotherms were measured at -196{degree}C under nearly 76cmHg using a commercially available full-automatic absorption measurement equipment. Based on the X-ray diffraction and TEM observation results on activated coals, the relation between the ...

Energy Technology Data Exchange (ETDEWEB)

Using gasoline as an example of additives for cold start improvement, fuel vapor composition of methanol-gasoline mixtures, fuel evaporation rate in consideration of temperature drop due to heat of fuel evaporation, air fuel ratio, stoichiometric air fuel ratio and excess air ratio of fuel vapor were calculated. The mixture formation of methanol-gasoline mixtures at low temperature in otto cycle engines was studied. Van Laar's empirical formula was used to estimate the partial pressure of high-percentage methanol blends. It was found that the most part of fuel vapor is occupied by gasoline, even when a small amount of gasoline is added to methanol resulting to an extremely small excess air ratio. It is obvious that this vapor pressure adjustment using gasoline is the dominant factor for improvement in cold startability. (10 figs, 1 ...

Energy Technology Data Exchange (ETDEWEB)

The purpose of the present work was to establish the flammability limits of hydrogen in air for upward vertical flame propagation at elevated temperatures up to 350 deg and atmospheric pressure in a conventional stainless steel test tube apparatus, and to investigate the extent to which a prolonged exposure (i.e., residence time) of the mixture to elevated temperatures before spark ignition may influence the value of the flammability limits. 9 refs.

British Library Electronic Table of Contents (United Kingdom)

In the present work, the plasma nitriding behavior of a nickel based dental alloy was investigated. Plasma nitriding experiments carried out under constant gas mixture (15% H2?85% N2) for different process parameters including time (4, 6, 10, and 20?h) and temperature (400, 450, 500, and 550??C). Depending on nitriding parameters, it was found that triple or double layers formed on the surface of the samples. Increasing of treatment time and temperature has resulted in a double layer. ?N1 layer was in formed all nitrided samples. However, ?N2 layer is formed only at low temperatures and in short times. Layer growth of nickel based alloys increases until a critical time or a critical temperature reached. Above these critical values, it is observed that the layer thickness decreases. It was ...

Energy Technology Data Exchange (ETDEWEB)

In this study, the effects of hydrogen peroxide on laminar, premixed, methane-air flames at atmospheric pressure and temperature were investigated using CHEMKIN III and GRI 3.5 mechanism. The range of fuel/air equivalence ratio {phi} was varied from 0.6 to 1.2, and the amount of hydrogen peroxide was altered from 0% to 20% volumetric fraction of the methane-hydrogen peroxide (air excluded) mixture. The burning velocity was found to increase with increasing hydrogen peroxide addition, with a relatively larger increase for the fuel-richer mixtures ({delta}S{sub u} up to 15 cm/s for {phi} {approx}=1.2). The adiabatic flame temperature rose with hydrogen peroxide addition, and the temperature rise per unit hydrogen peroxide addition was more significant ({delta}T up to 100 K) for the leaner mixtures. For the same mixture stoichiometry, adding ...

British Library Electronic Table of Contents (United Kingdom)

Biased above threshold (VT), pulsed photocurrent (u) measurements on windowed silicon Pd gate MOS capacitors are shifted (DV) negatively by H2/N2, whereas Au gates shift positively under NO2/air. Below VT, the shifts are reversed by adjustments of interface state population. Minor temperature increases may coax the device from inversion to depletion, inducing sign reversal of the chemical response.

British Library Electronic Table of Contents (United Kingdom)

Abstract Microbiological quality and biophenol content evolution was studied in minimally processed Thassos cv table olives by hot air dehydration under mild conditions (40C, 24-h, aw-=-0.893) and storage under characteristic packaging conditions (vacuum, 100% N2 and air) at 4 and 20C over a period of 180 days. No salt was used in the production line or packaging. The undesirable microorganisms (Enterobacteriaceae, Staphylococcus aureus, Bacillus, Clostridium) were undetectable until the end of the storage period. Also, modified atmospheres prevented fungal growth at both temperatures apart from the samples stored in air, in which Penicillium and Aspergillus spp. were identified. At 20C, a coexistence of mesophilic bacteria and yeasts occurred. At 4C, yeasts were the predominant microflora...

International Nuclear Information System (INIS)

With the aim of optimizing the nitriding process parameters (temperature and gas mixture ) experimental studies of the plasma nitriding of Ck 15 steel were carried out, using a D. C. glow discharge. Nitriding treatments were performed at 450, 500 and 550 and N_2/H_2 volume ratio of 3/1, 1/1 and 1/3 for 5 hours. Nitriding treatment produces modified surface layer consisting of an outer compound layer and an inner diffusion layer.The plasma nitriding of Ck 15 produce single white layer consisting of #gamma#-(Fe_4N).

International Nuclear Information System (INIS)

This study was the analyse the relationship between properties of ion nitrided Fe sintered material and parameters of plasma nitriding process. Pure fe sintered materials (relative density : 92%) were fabricated by hot-pressing and nitrided under pulsed DC plasma for 4 hours. The large number of parameters in plasma diffusion treatment allows close control of the process so that surface layers with defined microstructures and properties can be obtained. The number of micropores in nitriding layer can be reduced in pulsed DC plasma by reducing the plasma power and by varying the gas mixture. The phase constitution of compound layer of nitrided Fe sintered material were influenced by gas mixture (N_2 : H_2) and pulsed ratio (pulse on/off time ratio).

International Nuclear Information System (INIS)

Austenitic stainless steel AISI 304 has been nitrided by radio frequency (rf) plasma containing various nitrogen-hydrogen gas mixtures, in order to study the effect of hydrogen on structure and magnetic properties of the formed compound layer. The thermal temperature has been measured at the vicinity of the samples. The compound layer thus produced has been characterized using, X-ray diffractometer and vibration sample magnetometer. Providing the total pressure of nitrogen and hydrogen is held constant, the addition of hydrogen up to 50% gives new structural phases. The magnetization values of the plasma treated samples are strongly dependent on the percentage of H_2 in the gas phase. An excessive amount of hydrogen (#approx#75%) on the other hand, retards the nitriding process. The surface temperature of the sample and plasma condition is crucial factors for nitriding process.

Energy Technology Data Exchange (ETDEWEB)

A combination of degenerate four-wave mixing spectroscopy and a low-pressure sampling technique has been studied for isotopic analysis in an air-acetylene flame. Hyperfine spectra of D lines of sodium and several mixtures of lithium isotopes obtained in this way are presented.

British Library Electronic Table of Contents (United Kingdom)

In this work an experimental study is carried out to determine the thermo-hydraulic performance of an intercooler (IC) with flat tubes provided with triangular plain internal fins and louvered external fins when it is used on a car equipped with a low pressure EGR. The main unknowns to be answered are the thermo-hydraulic characteristics of the IC working under humid conditions induced by EGR, the conditions under which the water content in the mixture of air and exhaust gases begins to condense and the conditions under which the condensed water will be retained inside the IC. The exhaust gases are here replaced by a mixture of dry air and water vapour which are mixed upstream of the IC. The IC is submitted at the following testing conditions: on the ambient air side, the air temperature i...

Energy Technology Data Exchange (ETDEWEB)

One of the unsolved problems of the natural gas dual fuel engine is that there is too much exhaust of Total Hydrogen Carbon(THC) at a low equivalent mixture ratio. To fix it, a natural gas mixed with hydrogen was applied to engine test. The results showed that the higher the mixture ratio of hydrogen to natural gas, the higher the combustion efficiency. And when the amount of the intake air is reached to 90% of WOT, the combustion efficiency was promoted. But, like a case making the injection timing earlier, the equivalent mixture ratio for the nocking limit decreases and the produce of NOx increases. 5 refs., 9 figs., 1 tab.

Energy Technology Data Exchange (ETDEWEB)

A cathode of improved discharge characteristics for a zinc-air battery is prepared from mixtures containing gamma-MnO/sub 2/ 33-67 wt%, C 12-40 wt% and KOH 20-28 wt%.

Energy Technology Data Exchange (ETDEWEB)

The metal dependence of mesoporous activated carbons with various metal acetylacetonate (acac) particles prepared from Morwell coal was studied. In experiment, the mixture of Morwell coal and acac metal complexes were dissipated into tetrahydrofuran, and after agitation in Ar atmosphere, the solvent was removed by vacuum distillation. Coal specimens with Fe(acac)3, Ni(acac)2 and Co(acac)2 as acac complexes were activated by exchanging flow gas with water vapor after heat treatment in N2 gas flow at 900{degree}C. The pore sizes of the specimens were obtained from N2 adsorption isotherms by BET method and BJH method. Conditions of pores and metals in the specimens were examined by XRD measurement and TEM observation. The relation between the above conditions and pore characteristics obtained from adsorption experiment was also examined. As a result, the difference in mesopore ratio ...

International Nuclear Information System (INIS)

In the present investigation, the properties of plasma nitrided AISI 304 steel were studied by changing the presence of nitrogen in the gas mixture. The plasma nitriding was performed at temperature -560 deg C, pressure -4 mbar and duration 24 hours. The nitrided samples were characterized by evaluating the phase composition, micro hardness, and diffusion layer thickness. The phase analysis indicates the mixed phases of CrN and Fe_3N, Fe_3N and Fe_4N which has the highest intensity. The results show the glow discharge plasma nitriding in presence of N_2 (80 vol. %) and H_2 (rest) produced higher hardness as well as higher case depth. (author)

International Nuclear Information System (INIS)

The method for calculating emissions to air has been revised, which has led to adjustments. Because of this, emissions in 1999 cannot yet be compared with previous years. Emissions in 1990 - 1998 are being recalculated now using the new method and are expected to be ready during 2001. Emissions to air of carbon dioxide (CO_2) in Sweden was 56.58 million tonnes in 1999, not including emissions from biofuels and international bunkers. The major sources of CO_2 emissions are the combustion of fossil fuels and the use of fuels for mobile sources. Total emissions to air of sulphur dioxide (SO_2) and nitrogen oxides (NO_x, counted as NO_2) in Sweden was 66 000 and 263 000 tonnes respectively in 1999. International bunkers are not included. The major source of SO_2 emissions is combustion of fossil fuels. Road traffic is the major source of NO_x emissions. Emissions to air of methane (CH_4), nitrous oxide ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a nitrogen oxides decreasing combustion method which comprises: a first step of mixing a fuel and air with each other; a second step of bringing the mixture obtained in the first step into contact with a packed catalyst such that only catalytic combustion occurs; and a third step of adding a fresh supply of the fuel to a stream obtained from the second step to form a mixed gas and causing the mixed gas to undergo non-catalytic thermal combustion. The temperature of the packed catalyst is lower than the ignition temperature of the mixture and the adiabatic flame temperature of the mixed gas is lower than a temperature at which the nitrogen oxides occur.

Energy Technology Data Exchange (ETDEWEB)

Real fuels are complex mixtures of thousands of hydrocarbon compounds including linear and branched paraffins, naphthenes, olefins and aromatics. It is generally agreed that their behavior can be effectively reproduced by simpler fuel surrogates containing a limited number of components. In this work, an improved version of the kinetic model by the authors is used to analyze the combustion behavior of several components relevant to gasoline surrogate formulation. Particular attention is devoted to linear and branched saturated hydrocarbons (PRF mixtures), olefins (1-hexene) and aromatics (toluene). Model predictions for pure components, binary mixtures and multicomponent gasoline surrogates are compared with recent experimental information collected in rapid compression machine, shock tube and jet stirred reactors covering a wide range of conditions pertinent to internal combustion engines (3-50 atm, 650-1200K, ...

Energy Technology Data Exchange (ETDEWEB)

Coal demineralization mechanism and its optimum condition were studied by hydrothermal reaction between Ca(OH)2 and quartz as a coal demineralization model. In experiment, the mixture of powder quartz and Ca(OH)2 water slurry was subjected to reaction in an autoclave under spontaneous pressure at 175-340{degree}C. After dried in N2 gas atmosphere at 105{degree}C, the reaction product was analyzed by X-ray diffraction, thermo-balance and differential thermal analysis. In measurement of quartz conversion, the specimen was analyzed by X-ray diffraction after removal of bound water by heat treatment at 850{degree}C. The mixture of clean coal deashed by NaOH and a fixed amount of quartz was also used as specimen for experiment. As the experimental result, dicalcium silicate hydrate was mainly produced at 175{degree}C, and the product changed into xonotlite through tobermorite by longer treatment at higher ...

Energy Technology Data Exchange (ETDEWEB)

The characteristic rich shifting of the maximum adiabatic flame temperature from the stoichiometric value for mixtures of hydrocarbon and air is demonstrated to be caused by product dissociation and hence reduced amount of heat release. Since the extent of dissociation is greater on the lean side as a result of the stoichiometry of dissociated products, the peaking occurs on the rich side. The specific heat per unit mass of the mixture is shown to increase monotonically with increasing fuel concentration, and as such tends to shift the peak toward the lean side. It is further shown that this is the cause for the lean shifting of the adiabatic flame temperature of oxidizer-enriched mixtures of N{sub m}H{sub n} and F{sub 2} and of NH{sub 3} and O{sub 2}, with various amounts of inert dilution, even though their maximum heat release still peaks on the rich side. (author)

International Nuclear Information System (INIS)

In evaluating commercialization prospects for natural gas fuelled vehicles, this paper compares the performance and emission quality of these innovative vehicles with those using conventional fuels - gasoline and diesel fuels. Assessments are made of the state-of-the-art of current technology relative to fuel storage, air/fuel mixture preparation, in cylinder combustion processes and pollution control. The analysis evidences that while natural gas is an excellent fuel for spark ignition engines, in transport applications its use is hampered by large storage volume requirements and weight. Moreover, the air/fuel mixture preparation, combustion process and exhaust-gas cleaning require a greater research and development effort to make this alternative fuel economically and environmentally competitive with conventional fuels.

Energy Technology Data Exchange (ETDEWEB)

The catalytically stabilised thermal combustion (CST) of lean hydrogen-air mixtures was investigated numerically in a turbulent channel flow configuration using a two-dimensional elliptic model with detailed heterogeneous and homogeneous chemical reactions. Comparison between turbulent and laminar cases having the same incoming mean properties shows that turbulence inhibits homogeneous ignition due to increased heat transport away from the near-wall layer. The peak root-mean-square temperature and species fluctuations are always located outside the extent of the homogeneous reaction zone indicating that thermochemical fluctuations have no significant influence on gaseous combustion. (author) 4 figs., 6 refs.

Energy Technology Data Exchange (ETDEWEB)

The rechargeability of the slurry-Zn/air battery was demonstrated with a practical recharge cell that requires minimal hydraulic and mechanical energy for operation. A dendritic Zn was deposited on a Mg plate substrate from which it was easily, periodically and automatically scraped to regenerate dendritic Zn slurries. Excellent discharge results were obtained with the regenerated dendritic Zn slurry, comparable to those obtained with slurries made with mixtures of Zn powder. The dendritic Zn slurry allowed, however, twice the utilization of Zn. 13 refs., 24 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

Equations are derived to permit calculation of the work required for the isentropic compression of a two phase fuel-air mixture. Methanol evaporation during compression is shown to substantially reduce compression work and thereby improve cycle efficiency and maximum power. Effects of evaporative cooling in the intake manifold are calculated. 14 refs.

Energy Technology Data Exchange (ETDEWEB)

High pressure experiments in a jet-stirred reactor have been performed to study the NO{sub x} formation in lean premixed combustion of methane/air mixtures. The experimental results are compared with numerical predictions using four well known reaction mechanisms and a model which consists of a series of two perfectly stirred reactors and a plug flow reactor. (author) 2 figs., 7 refs.

Energy Technology Data Exchange (ETDEWEB)

In order to develop modern two-stroke engines with low fuel consumption, respectively with low exhaust emissions, two alternative development areas -- the mixture formation and the scavenging system -- have been correlated. For a satisfying mixture formation without fuel losses by scavenging, the direct injection seems to be one of the best solution for the high speed two-stroke engine of the future. On the other hand the modern development of two-stroke scavenging systems shows a large field of application and improvement methods of cross and loop scavenging. Based on the specific optimization factors of the injection system, respectively of the scavenging system, the aim off this common work of the Universities of Pisa and Zwickau is to correlate both the optimization fields in an advantageous mixture formation process. The principal elements of this correlation are the design of the combustion chamber, the position of ...

International Nuclear Information System (INIS)

A mixture of crushed rock and bentonite is being considered as backfill and sealant for high-level nuclear waste repositories. Many variables affect the hydraulic conductivity of such a mixture, including the size and shape of the rock particles, method of mixing, water content and density of the clay, and the weight ratio of rock to clay. Mixtures of crushed basalt and bentonite have been tested to determine the relative effects of these variables. Two types of permeameters are used, 20 cm diameter stainless steel permeameters and 10 cm diameter clear PVC permeameters. Plugs are installed as a single lift or in many lifts; the water content of the clay ranged from air-dry (in most cases) to as high as 200%. Preliminary results show that a mixture of 75% crushed basalt and 25% bentonite has a hydraulic conductivity between 1 x 10/sup -9/ cm/s and 2.5 x 10/sup -8/ cm/s. In some ...

Energy Technology Data Exchange (ETDEWEB)

The propagation of acoustic pressure perturbations in an adiabatic low-quality air/water flow were investigated both theoretically and experimentally. A linearized dispersion model is correlated with data to extract information on the behavior of interfacial momentum transfer controlled by the virtual volume coefficient. The dispersion model is examined in limiting cases of low and high frequency and related to current models for critical flow velocity. Fourier decomposition techniques are employed to predict the dispersion of measured pressure pulses and to relate data for standing waves and propagating pulses. The dispersion model is based on a two-fluid model and is the most complete model available in the literature at this time. The dispersion data presented herein is also the best available to date for low frequency (i.e., frequencies less than bubble resonance) sound propagation in bubbly air/water mixtures.

British Library Electronic Table of Contents (United Kingdom)

Abstract The available surface equation of state for pure pulmonary surfactant monolayers is generalised to binary mixture monolayers by introducing a group of parameters, i(i-=-1-4) in the form of $x_{r}^{\\beta _{i} } $ to express the influence of the components in new mixing rules and a new factor, I $\\left[ { = \\left( {\\prod\\limits_{i = 1}^{4} {\\beta _{i} } } \\right)^{{\\raise0.5ex\\hbox{$\\scriptstyle 1$}\\kern-0.1em/\\kern-0.15em\\lower0.25ex\\hbox{$\\scriptstyle {4}$}}} } \\right]$, is defined to represent the interaction intensity between two different components. The ---A isotherms getting by the surface equations of state agree with the experimental data for protein-lipid binary monolayers, and the average deviation is about 11.41%. The result shows the order of the interaction intensity b...

British Library Electronic Table of Contents (United Kingdom)

Bio-inspired silver nanoparticles were synthesized with the aid of a novel, non-toxic, eco-friendly biological material namely, banana peel extract (BPE). Boiled, crushed, acetone precipitated, air-dried peel powder was used for reducing silver nitrate. Silver nanoparticles were formed when the reaction conditions were altered with respect to pH, BPE content, concentration of silver nitrate and incubation temperature. The colorless reaction mixtures turned brown and displayed UV-visible spectra characteristic of silver nanoparticles. Scanning electron microscope (SEM) observations revealed the predominance of silver nanosized crystallites after short incubation periods. When the reaction mixtures were incubated for 15 days, some micro-aggregates were also observed. Energy dispersive spectr...

International Nuclear Information System (INIS)

Carbon monoxide can be produced in severe accidents from interaction of ex-vessel molten core with concrete. Depending on the particular core-melt scenario, the type of concrete and geometric factors affecting the interaction, the quantities of carbon monoxide produced can vary widely, up to several volume percent in the containment. Carbon monoxide is a combustible gas. The carbon monoxide thus produced is in addition to the hydrogen produced by metal-water reactions and by radiolysis, and represents a possibly significant contribution to the combustible gas inventory in the containment. Assessment of possible accident loads to containment thus requires knowledge of the combustion properties of both CO and H_2 in the containment atmosphere. Extensive studies have been carried out and are still continuing in the nuclear industry to assess the threat of hydrogen in a severe reactor accident. However the contribution of carbon monoxide to the combustion threat has received less ...

International Nuclear Information System (INIS)

This work presents a comparative study of low-alloy steel nitriding for different possible techniques. Active screen plasma nitriding (ASPN) is a successful surface modification method that has many advantages over the conventional DC plasma nitriding (CPN). The corrosion behavior of 30CrNiMo8 low-alloy steel has been examined using anodic polarization tests in 3.5% NaCl solution under varying conditions of ASPN and CPN processes. The process variables included active screen setup parameters, treatment temperature (550 and 580 deg. C), gas mixture (25/75 and 75/25 of N_2/H_2) and treatment time (5 and 10 h) in 500 Pa pressure. The structure and phases composition of the compound layer was studied by X-ray diffraction (XRD), microhardness tests, optical microscopy and scanning electron microscopy (SEM). It was observed that ASPN treated samples surface enhanced corrosion resistance while the temperature and/or hole size of ...

International Nuclear Information System (INIS)

Nitrogen doped Diamond-like carbon thin films were deposited on n-Si and SiO_2 substrates by rf magnetron sputtering using pure graphite (99.999%) as the target material and mixtures of Ar, N_2 and H_2 for plasma generation. The dependence of structural and optical properties on nitrogen content was investigated using XPS, Raman spectroscopy, FT-IR spectroscopy, and Ellipsometry studies. It was found that as the nitrogen content was increased in the plasma, sp"2 bonding favored. Also it was observed that oxygen contamination increased with nitrogen content. Typical C-H stretching modes connected with diamond-like carbon could be seen in FT-IR spectra. The I_D and I_G bands were well defined and it was observed that as nitrogen content increased I_G band was enhanced. Ellipsometry studies revealed that the optical constants like refractive index (n) and extinction co-efficient (k) increased with increase in nitrogen content ...

International Nuclear Information System (INIS)

Plasma nitriding is a powerful technique for modifying the phase-structure of the material surface layers, which affect the mechanical, physical and chemical properties of material. The effect of plasma nitriding on the surface properties of three types of steel (low carbon, AISI-304 and H13 (hardened)) has been investigated. The steel samples were plasma nitrided in vacuum of 10"-"1Pa with gas mixture of (N_2, H_2) at 530 Centigrade degree for a duration of 14 hours. Vickers microhardness measurements and XRD phase analysis of the treated and untreated samples were carried out. The diffraction patterns of treated steels revealed that new phases of #gamma#-Fe_4N, #epsilon#-Fe_3N and (Fe,Cr)_2N were formed. The maximum treated depths were about 5, 6 and 45 #mu#m for low carbon, AISI-304 and H13 (hardened) nitrided steel respectively. The microhardness was increased by about 150%, 200% and 140% for low carbon, AISI-304 and ...

International Nuclear Information System (INIS)

Several materials, lenses, dry bearings and cables were exposed to a tritiated moisture environment to study the behavior of tritium contamination on candidate materials for ITER remote handling equipment. To optimize the tritium removal procedure, decontamination experiments using a gas purge with three different moisture concentrations were also performed. The surface tritium concentrations of CeO_2 containing alkaline barium glass (NB), CeO_2 containing lead glass (LX) and synthetic quartz (Quartz) after the exposure experiments were 7.80, 10.94 and 0.67 Bq/cm"2, respectively. It was found that the tritium concentration was influenced by the compositions of the materials. The concentrations of tritium on type 831 (solid lubrication material: graphite) and type 237 (solid lubrication material: tungsten disulfate) dry bearings after the exposure experiments were 89.80 and 31.78 Bq/cm"2, respectively. The tritium concentration in an electric cable tested was 5014 Bq/g after HTO ...

Energy Technology Data Exchange (ETDEWEB)

A mathematical model was developed to predict the penetration of a transient fuel spray, the temporal and spatial distribution of air-fuel mixture before the end of ignition delay and the subsequent pressure rise during combustion in a Direct-Injection Diesel Engine with and without swirl. The model accounts for the non-isothermal and non-isobaric character of processes during fuel injection resulting from continuous motion of the piston. The effects of various engine operating variables on spray were studied and graphically presented. The calculated spray penetration with and without crossflow of air is compared with the available experimental data of other researchers with good agreement. The model can predict the rate of combustible-mixture formation, the rate of heat release and cylinder pressure as a function of time in direct injection (DI) diesel engine. A single-cylinder D.I. research diesel ...

Energy Technology Data Exchange (ETDEWEB)

Flame lengths inside circular tubes, using an (in-shot) atmospheric burner design commonly found in gas-fired residential furnaces were visually observed for natural gas and air under various operating conditions. The flame length data were reduced into dimensionless flame lengths, which were shown to be linearly proportional to the Peclet number of the fuel and air mixture. The dimensionless flame length dependence reported does not scale according to the classical flame models: pre-mixed (laminar) flame or diffusion flame. Instead, the flame length dependence was found to scale with the fuel burn speed, gas/mixture properties (evaluated at the adiabatic flame temperature), and flow parameters. Currently, this is the only flame length study available for the standard atmospheric burner designs commonly used in residential heating products. The results and data reduction provide an easy method to ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the results obtained from two large experimental facilities built at Sandia National Laboratories in Albuquerque, NM. FLAME (Flame Acceleration Measurements and Experiments) is a large horizontal rectangular channel designed to study flame acceleration, transition to detonation, simulation of combustion in containment geometries, component heating, and other problems in hydrogen combustion relevant to reactor safety. The Heated Detonation Tube has been designed to study detonations in hydrogen-air-steam mixtures. Both facilities have been in operation for just over a year. 12 figures.

International Nuclear Information System (INIS)

For pt.I see ibid., vol.516, p.426-48, 1998. Manifest N=2 supersymmetric hypermultiplet mass terms can be introduced in the projective N=2 superspace formalism. In the case of complex hypermultiplets, where the gauge covariantized spinor derivatives have an explicit representation in terms of gauge prepotentials, it is possible to interpret such masses as vacuum expectation values of an Abelian vector multiplet. The duality transformation that relates the N=2 off-shell projective description of the hypermultiplet to the on-shell description involving two N=1 chiral superfields allows us to obtain the massive propagators of the N=1 complex linear fields in the projective hypermultiplet. The N=1 massive propagators of the component superfields in the projective hypermultiplet suggest a possible ansatz for the N=2 massive ...

International Nuclear Information System (INIS)

A hydrogen combustion and exhaust emissions in a supercharged gas engine ignited with micro pilot diesel fuel was discussed in this presentation. A schematic diagram of the experimental study was first presented. The single cylinder, water-cooled, supercharged test engine was illustrated. Results were presented for the following: fuel energy and energy share (hydrogen and diesel fuel); pressure history and rate of heat release; engine performance and exhaust emissions; effect of nitrogen dilution on heat value per cycle; effect of N_2 dilution on pressure history and rate of heat release; and engine performance and exhaust emissions. This presentation demonstrated that smooth and knock-free engine operation results from the use of hydrogen in a supercharged dual-fuel engine for leaner fuel-air equivalence ratios maintaining high thermal efficiency. It was possible to attain mor3 than 90 per cent hydrogen-energy substitution ...

Energy Technology Data Exchange (ETDEWEB)

The operation of Diesel engines on gaseous fuels, commonly known as dual fuel engines, uses Diesel fuel as the pilot fuel and gaseous fuel (methane and sometimes propane in the present work) as the main fuel. The gaseous fuel was inducted in the intake manifold to mix with the intake air. The investigation was conducted on a high speed indirect injection (Ricardo-E6) dual fuel engine and was concerned with the effects of exhaust gas recirculation (EGR) on the dual fuel engine combustion and emissions, in particular, the effects of intake air temperature and diluent admissions (N{sub 2} and CO{sub 2}) on combustion and emissions. The use of diluents to displace oxygen (O{sub 2}) in the intake air resulted in a reduction in the O{sub 2} supplied to the engine, increased the inlet charge thermal capacity (thermal effect) and, potentially, CO{sub 2} and N{sub 2} participated in the combustion process (chemical effect). In a ...

Energy Technology Data Exchange (ETDEWEB)

In order to establish coal NOx preventive measures, discussions were given on formation of N2 in the fixed-bed pyrolysis of low rank coals and the mechanisms thereof. Chinese ZN coal and German RB coal were used for the discussions. Both coals do not produce N2 at 600{degree}C, and the main product is volatile nitrogen. Conversion into N2 does not depend on heating rates, but increases linearly with increasing temperature, and reaches 65% to 70% at 1200{degree}C. In contrast, char nitrogen decreases linearly with the temperature. More specifically, these phenomena suggest that the char nitrogen or its precursor is the major supply source of N2. When mineral substances are removed by using hydrochloric acid, their catalytic action is lost, and conversion into N2 decreases ...

International Nuclear Information System (INIS)

Cross-sections for "8"4Sr(n, 2n)"8"3Sr, "8"6Sr(n, 2n)"8"5"mSr, "8"6Sr(n, 2n)"8"5Sr, "8"8Sr(n, 2n)"8"7"mSr, "8"4Sr(n, p)"8"4Rb, "8"6Sr(n, p)"8"6Rb, "8"8Sr(n, p)"8"8Rb and "8"8Sr(n, #alpha#)"8"5"mKr reactions have been measured at neutron energies from 13.5 to 14.6 MeV using activation technique and by means of #gamma#-ray spectrometry. The neutron flux was determined using the monitor reaction "9"3Nb(n, 2n)"9"2"mNb and the neutron energies were measured by the method of cross-section ratios for "9Zr(n, 2n)"8"9Zr to "9"3Nb (n, 2n)"9"2"mNb reactions. The results of present work are compared with data published previously.

International Nuclear Information System (INIS)

Short communication.

CERN Document Server

We propose the exact boundary S matrix for breathers of the N=2 supersymmetric sine-Gordon model. We argue that this S matrix has three independent parameters, in agreement with a recently-proposed action. We also show, contrary to a previous claim, that the ``universal'' supersymmetric boundary S matrix commutes with two supersymmetry charges. General N=2 supersymmetric boundary integrable models are expected to have boundary S matrices with a similar structure.

Energy Technology Data Exchange (ETDEWEB)

In January 1981, a dual-fuel engine of type 8L52/55 ADG, with the highest cylinder rating of all four-stroke gas engines currently available, succesfully completed its test run on M.A.N.s test bed at Augsburg. The engine can be operated either on Diesel oil or on gas and pilot oil and can be switched from Diesel to gas operation or vice versa at any load during operation. In gas operation, the engine works on the pilot injection principle. By changing from pulse-pressure to constant-pressure turbocharging, matching the charge-air pressure, improving mixture formation and optimising the injection system, M.A.N. has succeeded in achieving a high power output while reducing the heat consumption in gas operation almost to its level in Diesel operation. A close look is taken at the design features which distinguish the dual-fuel engine from the 52/55 A Diesel engine, such as the gas supply, injection system and automatic change-over system. ...

Energy Technology Data Exchange (ETDEWEB)

Real-time neutron radiography is being evaluated for studying the dynamic behavior of two-phase flow and for measuring void fraction in vertical and inclined water ducts. This technique provides a unique means of visualizing the behavior of fluid flow inside thick metal enclosures. An air-water flow system was constructed to simulate vapor conditions encountered in a fluid flow duct. Air was injected into the bottom of the duct at flow rates up to 0.47 {ell}/s (1 ft{sup 3}/min). The water flow rate was varied between 0 and 3.78 {ell}/min (0 to 1 gal/min). The experiments were performed at the Pennsylvania State University nuclear reactor facility using a real-time neutron radiography camera. With a thermal neutron flux on the order of 10{sup 6} n/cm{sup 2}{center_dot}s{sup {minus}1} directed through the thin duct dimension, the dynamic behavior of the air bubbles was clearly visible through 5-cm (2-in.)-thick aluminum ...

International Nuclear Information System (INIS)

Real-time neutron radiography is being evaluated for studying the dynamic behavior of two-phase flow and for measuring void fraction in vertical and inclined water ducts. This technique provides a unique means of visualizing the behavior of fluid flow inside thick metal enclosures. An air-water flow system was constructed to simulate vapor conditions encountered in a fluid flow duct. Air was injected into the bottom of the duct at flow rates up to 0.47 ell/s (1 ft"3/min). The water flow rate was varied between 0 and 3.78 ell/min (0 to 1 gal/min). The experiments were performed at the Pennsylvania State University nuclear reactor facility using a real-time neutron radiography camera. With a thermal neutron flux on the order of 10"6 n/cm"2#centre dot#s"-"1 directed through the thin duct dimension, the dynamic behavior of the air bubbles was clearly visible through 5-cm (2-in.)-thick aluminum support plates placed on both ...

Energy Technology Data Exchange (ETDEWEB)

An automotive powertrain includes a conventional piston engine, a continuously variable ratio transmission, an engine speed sensor and a feedback control system. The control system adjusts both the transmission ratio and the throttle valve in the engine carburetor or fuel metering system in response to the position of the accelerator pedal and in response to the crankshaft speed as measured by the engine sensor. The transmission provides extreme overdrive gear ratios which allow the engine to be operated at wide open throttle even during moderate cruising, and, in addition, the engine carburetor or fuel metering system is calibrated to deliver to the engine a stoichiometric air-fuel mixture which is combined, before combustion, with a special proportion of recirculated exhaust gas. As a result of extensive wide open throttle engine operation with the above mentioned intake charge composition, combustion variables are optimized to produce ...

Energy Technology Data Exchange (ETDEWEB)

Part of the crushed activated charcoal (about 20-50%) designed for manufacture of electrodes is made water repellant with the help of an aqueous suspension of water repelling agent containing 3-15% (preferably 10%) dry substance. After this the remaining part of the activated charcoal and the other additives are mixed with the water repelling part. The plates or tape which is rolled to an assigned thickness are pressed from the obtained mixture. The electrodes obtained by this method have a thin active layer and a porous structure and have good diffusion properties. They can be loaded by currents up to 80 mA/cm/sup 2/ without causing excessive polarization losses, and their service life is greater than or equal to 100 h.

British Library Electronic Table of Contents (United Kingdom)

To analyze the effect of containment spray on gas mixing and depressurization, two experiments (ST3_1 and ST3_2) were performed with two interconnected vessels. These experiments were conducted in the frame of the OECD/SETH-2 project using the PANDA facility. The vessels were preconditioned such that a helium-rich layer is formed in the upper section of the first vessel, henceforth referred to as Vessel-1. In the case of the first experiment (ST3_1), the remaining volume of Vessel-1 and the entirety of the second vessel, Vessel-2, were filled with pure steam. For ST3_2, the second experiment presented here, pure steam was replaced with a steam-air mixture instead. Water was injected from the top of Vessel-1 with a spray nozzle projecting downwards. Transient behavior of system pressure, as...

Energy Technology Data Exchange (ETDEWEB)

Measurements of local mass fluxes of liquid, local number fluxes of the drop and local drop size distributions at various locations in the test column were made for wide ranges of liquid flow rates and gas flow rates. An empirical correlation for the volume mean diameter of the drop at the nozzle exit was proposed. Measurements of the rates of absorption of carbon dioxide from carbon dioxide-air mixtures with water sprays (physical absorption) and aqueous sodium hydroxide sprays (chemical absorption) were made for wide range so fluid flow rates, feed gas concentrations, and initial alkali concentrations. The observed dimensionless rates of absorption were compared with the theoretical values by assuming penetration model with second-order irreversible reaction. 11 refs., 7 figs.

Energy Technology Data Exchange (ETDEWEB)

It has been shown that two-dimensional arrays of rigid or fluidlike cylinders in a fluid or a gas define, in the limit of large wavelengths, a class of acoustic metamaterials whose effective parameters (sound velocity and density) can be tailored up to a certain limit. This work goes a step further by considering arrays of solid cylinders in which the elastic properties of cylinders are taken into account. We have also treated mixtures of two different elastic cylinders. It is shown that both effects broaden the range of acoustic parameters available for designing metamaterials. For example, it is predicted that metamaterials with perfect matching of impedance with air are now possible by using aerogel and rigid cylinders equally distributed in a square lattice. As a potential application of the proposed metamaterial, we present a gradient index lens for airborne sound (i.e. a sonic Wood lens) whose functionality is demonstrated by multiple ...

International Nuclear Information System (INIS)

Fourier transform infrared absorption spectroscopy has been used for the determination of the line strengths of 41 CO and CO_2 absorption lines at temperatures between 295 and 1250 K. The CO vibrational-rotational lines were from the P branch of the fundamental absorption band (2150--1950 cm"-"1) while the CO_2 vibrational-rotational lines were from the far wing of the R branch of the #nu#_3 fundamental band (2395--2380 cm"-"1). The intensities of the lines were measured from absorption spectra recorded in a high-temperature gas cell containing known concentrations of CO/CO_2/N_2 gas mixtures at atmospheric pressure. Absorption spectra were recorded through the cell with the use of a moderate-resolution Fourier transform infrared spectrometer. The absorption spectra were mathematically corrected for distortions resulting from the finite resolution of the spectrometer and for peak overlap. Line strength measurements were ...

International Nuclear Information System (INIS)

Previous flow regime studies have been for horizontal, vertical, and inclined pipe flow. As such, only a few studies have been performed on bundle geometries. The present paper examines the flow regimes for a vertical hexagonal flow channel with and without a finned fuel bundle. This type of a 36 finned rod hexagonal fuel bundle in parallel hexagonal flow channels is used in a MAPLE (Multi- purpose Applied Physics Lattice Experimental) type nuclear reactor. An experiment apparatus was designed consisting of the flow channel, inlet plenum and an air-water separator. The inlet plenum is used to provide a uniform mixture of air and water before entering the hexagonal flow channel. A turbine flow meter is used to determine the water flow rate. The turbine flow meter is calibrated for a low flow range and limits the measurable flow to 50 l/min. Flow pattern observation is determined by a SONY video camera, Real-Time Neutron ...

Energy Technology Data Exchange (ETDEWEB)

A diesel engine having staged injection for using lower cetane number fuels than No. 2 diesel fuel. The engine includes a main fuel injector and a pilot fuel injector. Pilot and main fuel may be the same fuel. The pilot injector injects from five to fifteen percent of the total fuel at timings from 20.degree. to 180.degree. BTDC depending upon the quantity of pilot fuel injected, the fuel cetane number and speed and load. The pilot fuel injector is directed toward the centerline of the diesel cylinder and at an angle toward the top of the piston, avoiding the walls of the cylinder. Stratification of the early injected pilot fuel is needed to reduce the fuel-air mixing rate, prevent loss of pilot fuel to quench zones, and keep the fuel-air mixture from becoming too fuel lean to become effective. In one embodiment, the pilot fuel injector includes a single hole for injection of the fuel and is directed at approximately ...

Energy Technology Data Exchange (ETDEWEB)

The objective of this project was to develop a explosion suppression system capable to confine and extinguish gas explosions of the type produced in sub level caving faces when blasting to the coal pillar. Existing systems, such as triggered barriers, were considered not to be valid because of size, weight, cost, and other operational constraints. The research activities have been focused in the development of a mixed water/air spray system that should be manually activated some second before blasting. Two prototypes have been developed and tested, the first one using nozzle operating at the standard ranges of pressure that are normally available in underground coal mines, and a second one based in high-pressure nozzles. In this case, bottles containing a pressurized air/water mixtures are required. The works carried out included theoretical studies, hydraulic nozzles characterization, and modelling of the explosion ...

Energy Technology Data Exchange (ETDEWEB)

Contaminated wood treatment sites can result in adverse health effects to nearby residents. Environmental exposure can be estimated by measuring concentrations of pollutants in air, water, food, or wipe tests. This environmental exposure value can be used as a surrogate to estimate individual exposure. The objective of this study was to determine whether or not pentachlorophenol (PCP) could be found in potentially exposed residents and if the dioxin levels are consistent with PCP exposure. A further objective of the study was to determine whether or not PAH-DNA adducts could be found in the potentially exposed residents. We present results of biomonitoring studies in residents living near a wood treatment plant that used coal-derived creosote and PCP to process and treat wood for over 100 years. The plant was built in 1904 and used creosote and PCP. Creosote is a complex mixture that contains numerous polycyclic aromatic hydrocarbons (PAHs). ...

DEFF Research Database (Denmark)

Udgivelsesdato: 2008

International Nuclear Information System (INIS)

Based on the results obtained for C-N and Si-C-N films, a systematic investigation of reactive magnetron sputtering of hard quaternary Si-B-C-N materials has been carried out. The Si-B-C-N films were deposited on p-type Si(100) substrates by dc magnetron co-sputtering using a single C-Si-B target (at a fixed 20% boron fraction in the target erosion area) in nitrogen-argon gas mixtures. Elemental compositions of the films, their surface bonding structure and mechanical properties, together with their oxidation resistance in air, were controlled by the Si fraction (5-75%) in the magnetron target erosion area, the Ar fraction (0-75%) in the gas mixture, the rf induced negative substrate bias voltage (from a floating potential to -500 V) and the substrate temperature (180-350 deg. C). The total pressure and the discharge current on the magnetron target were held constant at 0.5 Pa and 1 A, respectively. The energy and flux of ...

Energy Technology Data Exchange (ETDEWEB)

The Hydrogen Program at Sandia National Laboratories is developing internal combustion engine generators for application in series hybrid vehicles and stationary power units. The program consists of two approaches: investigating the utilization of hydrogen in a conventional crankshaft driven engine and in an advanced free piston configuration. The conventional engine program has taken the direction of utilizing the unique ability to spark ignite homogeneous fuel/air mixtures of hydrogen at low equivalence ratios to achieve low NO{sub x} emissions and high thermal efficiency. The goal is to translate the indicated thermal efficiency of single-cylinder engines into multicylinder configurations achieving at least 40% brake thermal efficiency. When coupled to an electrical generator, the fuel to electricity conversion efficiency would be approximately 37%. A modified Perkins 3.152 Diesel engine is currently being tested and has achieved an ...

International Nuclear Information System (INIS)

The cross sections of "2"0"4Pb(n,2n)"2"0"3Pb and "2"0"6Pb(n, #alpha#)"2"0"3Hg reactions have been measured by using the activation method in the neutron energy range of 13.50-14.81 MeV. Neutron fluence dose was calibrated with the cross sections of "2"7Al(n, #alpha#)"2"4Na reaction and neutron energies were determined by using the cross section ratios of "9"0Zr(n,2n)"8"9"m"+"gZr to "9"3Nb(n,2n)"9"2"mNb reactions. The results obtained are compared with the published data.

Science.gov (United States)

and propels the projectile to a velocity sufficient to reach ..... CLF3 + N2 4 .... 5 inches or greater accelerates a finned projectile to the veloc ...

Energy Technology Data Exchange (ETDEWEB)

This dissertation is devoted to the study of the phenomenological consequences of the three-generation heterotic string models based on the Calabi-Yau compactifications and the N = 2 superconformal constructions.

International Nuclear Information System (INIS)

... kinetics chemical reactions energy dependence ion-molecule collisions milli

CERN Document Server

We study N=2 SuperVirasoro SCFT for the generic value of the central charge. The main tool is the nonstandard bosonisation suggested in \\ref\\rRoz{L. Rozansky a letter to M. Bershadsky, 1989}, \\ref\\rSeBGR{B. Gato-Rivera, A. Semikhatov Phys. Letts. B293 (1992) 72},\\ref\\rBLNW{M. Bershadsky, W. Lerche, D. Nemeshansky, N. Warner N=2 Extended superconformal structure of Gravity and W Gravity coupled to Matter HUTP-A034/92}. The free field resolutions for the irreducible representations are obtained; the characters of these representations are computed. The quantum hamiltonian reduction from the Kac-Moody $\\hat{sl}_k(2|1)$ to N=2 $SVir$ is constructed.

International Nuclear Information System (INIS)

Nuclear Reaction Analysis (NRA) with deuteron ion beams has been used to probe for ion implanted nitrogen and carbon with high sensitivity in zinc oxide and silicon single crystals. The ion implanted N was measured using 1.4 MeV deuteron ion beams and was found to be in agreement with calculated values. The limit of detection for N in ZnO is 8x1014 ions cm-2. Raman measurements of the ion implanted samples showed three additional modes at 275, 504, and 644 cm-1 compared to the un-implanted ZnO crystals. The NRA and Raman results provided information on the N concentration, depth distribution, and structural changes that occur in dependence on the nitrogen ion fluences. The deuterium induced 12C(d,p)13C reaction was used to measure the carbon impurity/dose in ion implanted silicon. It was found that the use of a large cold shield (liquid nitrogen trap) in the ion implanter chamber greatly reduces the amount of carbon impurity on the surface of ion implanted silicon. Various ...

International Nuclear Information System (INIS)

Throughout the last decades, plasma technology has been established in a series of surface treatment applications, e.g. for semiconductor processing or optical coatings. The majority of plasma assisted technologies is based on low pressure processes. In recent years, however, non-thermal atmospheric pressure discharges have attracted considerable interest because of their simplified technical devices for industrial applications as compared to low pressure processes which require vacuum equipment. Hence, batch processing can be avoided, thus facilitating the implementation of plasma process steps into production lines. Investment costs are cut down significantly. The use of atmospheric pressure plasmas for technical applications dates back to the ozone production with dielectric barrier discharges (DBD) by Siemens in 1857. Lately, the application of atmospheric pressure plasmas for surface treatment has been reported, e.g. for the treatment of foils to improve printability, for surface ...

Science.gov (United States)

Page 1. REENGINEERING AIR MOBILITY: A PROCESS PERSPECTIVE ... REENGINEERING AIR MOBILITY: A PROCESS PERSPECTIVE ...

International Nuclear Information System (INIS)

We study the relationship between tachyons in N=2 superconformal tensor product models and topology changing of the defining polynomial of corresponding algebraic varieties. We show that monomials which correspond to tachyons change the topology of the defining polynomial if they are added whereas those corresponding to massless and massive fields do not. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Precondition for the low-NO operation of gas turbine burners is the generation of as homogeneous as possible a gaseous fuel/air mixture. Such a burner behavior can be achieved by selective adaptation of the flow and injection. A computing model is introduced that calculates the dynamically balanced GASs/droplet flow through numerical solution of the transport equations in a curved orthogonal coordinate system. The feedback reaction of the fuel droplets to the gas phase is considered by source terms and/or sink terms. Test computations were carried out for comparison with analytical solutions from the flow mechanics and validated by comparison with measurement results. Droplet motion and evaporation were checked by means of published experimental results on single droplets. For the validation of the developed computing technique, model tests were carried out with water in place of fuel. It is pointed out that the choice of different parameters ...

Energy Technology Data Exchange (ETDEWEB)

Two-phase pressure drop and fluctuating static pressures were measured in a small horizontal rectangular channel (hydraulic diameter = 5.44 mm). The two-phase fluid was an air/water mixture at atmospheric pressure tested over a mass flux range of 50 to 2,000 kg/m[sup 2] [center dot] s. Two-phase flow patterns were identified and an objective method was found for determining the flow pattern transition from bubble or plug flow to slug flow. The method is based on an RMS static pressure measurement. In particular, it is shown that the transition is accompanied by a clear and abrupt increase in the RMS pressure when plotted as a function of mass quality. Use of the RMS pressure as a two-phase flow pattern transition indicator is shown to have advantages over pressure-versus-time trace evaluations reported in the literature. The transition is substantiated by a clear local change in slope in the curve of two-phase pressure drop plotted as a ...

Energy Technology Data Exchange (ETDEWEB)

The plasma plume generated by a new type of high energy Janitor known as the railplug, is examined. The railplug is a miniaturized railgun that has the potential for improving ignition characteristics of combustible mixtures in engines. The objective of the study is to gain an uderstanding of the characteristics of the plasma created by a transparent railplug, and to validate a multidimensional computer simulation of the plasma and shock fronts. The nature of the plume emitted by the railplug was examined for three levels of electrical energy while firing into air at a pressure of 1 atm. The computer model is to be used to predict trends in railplug performance for various railplug designs, energies, and ambient conditions. The velocity of the plasma movement inside a transparent railplug was measured, as well as the velocity of the plume ejected from the cavity. A shock is produced at the initiation point of the arc and propagates down the ...

Energy Technology Data Exchange (ETDEWEB)

The results of an experimental investigation of the performance of a small bore engine with a swirl chamber when operating as a dual fuel engine with commercial methane as the gaseous fuel were presented in this paper. The experiment involved using a 3-dimensional computational fluid dynamics model to predict the performance of the engine. A detailed chemical kinetics for the gaseous fuel component, consisting primarily of methane and a reduced detailed chemical kinetics for the diesel fuel while considering the turbulent combustion processes an associated performance of a dual fuel engine with a swirl chamber were incorporated in the simulation. The study experimentally and numerically investigated the effects of changes in the quantities of the liquid fuel pilot and gaseous fuels on the combustion processes, engine performance, cyclic variations, and emissions. The paper discussed the experimental approach and results. It also discussed the simulation of the dual fuel engine ...

Energy Technology Data Exchange (ETDEWEB)

Two-phase flow patterns and frictional pressure gradients in flow in small, rectangular channels are being studies as part of a larger research program addressing phase-change heat transfer of pure refrigerants and refrigerant mixtures in plate-fin heat exchangers. Small rectangular flow channels were selected as representative of plain fin geometries. The particular channel reported herein has dimensions of 19.05 {times} 3.18 mm. Adiabatic flows of air/water mixtures, with the flow channel horizontal and the channel exit at near-atmospheric conditions, were utilized in the experiments. Analysis and interpretation of the pressure data relative to observed flow pattern transitions led to an objective method for determining the plug/bubble-to-slug flow transition. This method, together with visual observations, supplemented with photographic data, was used to develop a flow pattern man. A comparison of existing flow pattern ...

Energy Technology Data Exchange (ETDEWEB)

To prove that two-layer, TBP-nitric acid mixtures can be safely stored in the canyon evaporators, it must be demonstrated that a runaway reaction between TBP and nitric acid will not occur. Previous bench-scale experiments showed that, at typical evaporator temperatures, this reaction is endothermic and therefore cannot run away, due to the loss of heat from evaporation of water in the organic layer. However, the reaction would be exothermic and could run away if the small amount of water in the organic layer evaporates before the nitric acid in this layer is consumed by the reaction. Provided that there is enough water in the aqueous layer, this would occur if the organic layer is sufficiently thick so that the rate of loss of water by evaporation exceeds the rate of replenishment due to mixing with the aqueous layer. This report presents measurements of mass transfer rates for the mixing of water and butanol in two-layer, TBP-aqueous ...

Energy Technology Data Exchange (ETDEWEB)

The Electrohydrodynamic (EHD) is an active heat transfer augmentation technique which utilizes the effect of secondary motions generated through the application of an electrostatic potential to a dielectric fluid. Net result is better momentum and heat transfer between the fluid and the heat transfer wall through destabilization of the thermal boundary layer and better mixing of the fluid adjacent to the heat transfer surface. EHD enhancement of refrigerant/refrigerant oil mixtures heat transfer using the Electrohydrodynamic (EHD) technique is the subject of a three-year experimental investigation in a project funded by the US Department of Energy, effective June 1, 1993. For the interim period between November 1992 and June 1993 when the DOE funds became available, the Air-Conditioning and Refrigeration Technology Institute (ARTI) provided partial funding for our EHD research program with the aim of accomplishing three major tasks: (1) conduct ...

Energy Technology Data Exchange (ETDEWEB)

The invention relates to a method for purifying a gas mixture containing at least one undesirable gas compound utilizing certain sulfonamide or sulfamide solvents.

International Nuclear Information System (INIS)

Page 1. ANALYSIS OF REACTION MIXTURE OF LAURIC ACID WITH MONO-

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Uniaxial low-cycle fatigue and creep-fatigue tests have been carried out on hollow alloy 800 specimens that were either filled with air or with a molten mixture of sodium nitrate, potassium nitrate and an oxidizer. Low-cycle fatigue tests were carried out at 1200/sup 0/F and 650/sup 0/F by cycling the strain continuously between equal mangitude of tensile and compressive values at a rate of 4 x 10/sup -3/sec/sup -1/ until failure. The creep-fatigue tests were carried out at 1200/sup 0/F. The loading cycle differed from that of low-cycle fatigue testing only in the imposition of a hold at the peak compressive strain in each cycle. Cracks always initiated on the inner surface of the hollow specimen, and therefore, corrosive effects on crack propagation and initiation were controlled by the environment within the specimen cavity. In common with tests carried out earlier on steam-filled alloy 800 specimens, at 1200/sup 0/F in the presence of molten ...

Energy Technology Data Exchange (ETDEWEB)

In this investigation natural gas has been used as an alternative fuel in diesel engines. Experiments have been performed to study the performance of the dual fuel engine with different diesel quantities as pilot injection. It was suggested in this research that combustion in the dual fuel engine occurred in four stages: the delay period, the slow stage of combustion, the rapid stage of combustion and the fourth stage of combustion. Because of the slower flame speed of natural gas and also because of the prolonged delay period, the combustion of the gas-air continued well into the expansion stroke. These resulted in lower efficiency and higher brake specific fuel consumption, and also higher exhaust gas temperature and higher carbon monoxide in the exhaust when the engine ran on dual fuel. The carbon dioxide and black smoke in the exhaust decreased as the gas was introduced in the engine. The ratio of alternative to diesel fuel was varied at the same load also at ...

British Library Electronic Table of Contents (United Kingdom)

The effect of complexing agents DTPA and H2C2O4 on the extraction-chemical behavior of Tc, as applied to extractive splitting of U and Pu in the Purex process, was studied. The kinetic relationships of catalytic decomposition of N2H5NO3 under the action of Tc in the presence of these agents were determined. Variation of the ratio of the oxidized and reduced Tc species in the course of this process at various HNO3 concentrations was examined. In the final step of the reaction of N2H5NO3 with Tc in a nitric acid solution, when the reductant content is stabilized, the oxidation of reduced Tc also stops or continues at a considerably lower rate than before stabilization. The presence of DTPA decreases the rate of Tc(IV) oxidation owing to its binding in a complex and decreases the fraction of ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The experimental effect investigation programme on Zircaloy-4/air oxidation was pursued and expanded to isothermal specimen exposure and the comparison of the oxidation between the atmospheres Ar/O{sub 2} and air. In close connection with the EC project OPSA, which is meanwhile terminated, the investigation concerned specimen exposure in a thermobalance to flowing atmospheres, namely dry Ar/O{sub 2} of composition 80/20 or synthetic air, respectively. As test parameters the linear heat-up rate was varied in the range 5 to 40 K/min and the ramp or holding temperature between 800 and 1500 C. Mass increase and reaction rate were continuously recorded or evaluated in temperature/time dependence. The oxide scale growth was found to be accompanied by colour changes, crack formation and spalling of layers, as well as by dimensional substrate growth, which are the reasons for the observed kinetic results. The microstructural ...

CERN Document Server

Recently we discovered and discussed non-Abelian duality in the quark vacua of N=2 super-Yang-Mills theory with the U(N) gauge group and N_f flavors (N_f>N). Both theories from the dual pair support non-Abelian strings which confine monopoles. Now we introduce an N=2-breaking deformation, a mass term \\mu{\\mathcal A}^2 for the adjoint fields. Starting from a small deformation we eventually make it large which enforces complete decoupling of the adjoint fields. We show that the above non-Abelian duality fully survives in the limit of N=1 SQCD, albeit some technicalities change. For instance, non-Abelian strings which used to be BPS-saturated in the N=2 limit, cease to be saturated in N=1 SQCD. Our duality is a distant relative of Seiberg's duality in N=1 SQCD. Both share some common features but have drastic distinctions. This is due to the fact that ...

International Nuclear Information System (INIS)

The details and principles of an apparatus built for measurements of fluorescence quantum yields and cascade-free lifetimes of open-shell cations are reported. These rely on the detection of coincidences between energy selected photo-electrons and undispersed photons. The results of such measurements for CO"+_2,COS"+,CS"+_2 and N_2O"+ in selected vibrational levels of their excited states are presented. Non-unity fluorescence quantum yields are found for some vibronic levels of CO"+_2(B), COS"+(A), N_2O"+(A) and a non-exponential decay is observed for CS"+_2(B). The data yield the following values for the radiative lifetimes: CO"+_2(A) 124 +- 6 ns,CO"+_2(B) 140 +- 7 ns, COS"+(A) 550 +- 50 ns and N_2O"+(A) 240 +- 12 ns. (orig.).

Environmental Research Database

ObjectivesThe specific objectives of the research are to: 1. Determine the concentrations of N2O, NO and NO2 in tropical coastal waters in relation to nutrients and salinities. 2. Determine, with excess nitrate present, the potential for nitrate reduction and denitrification in sediments along tropical estuaries, and whether NO, NO2, N2O, N2 or NH4+ are significant products. 3. Establish the balance between denitrification, nitrate ammonification and anammox in tropical estuarine sediments, relative to [continued...]DescriptionThe coastal zone is extremely important in the biogeochemical processes which control the natural cycle of elements of the Earth. In particular, the coastal zone contributes significantly to the nitrogen cycle, removing nitrogen washed in from the land by rivers and so reducing its fertilizing impact on the coastal seas. However, these ...

International Nuclear Information System (INIS)

Cross sections for (n,2n) (n,p) (n,#alpha#), and (n,d*)"1 reactions have been measured on ruthenium isotopes at the neutron energies of 13.5 to 14.8 MeV using the activation technique in combination with high-resolution gamma-ray spectroscopy. Data are reported for the following reactions: "1"0"4Ru(n,2n)"1"0"3Ru, "9"8Ru(n,2n)"9"7Ru, "9"6Ru(n,2n)"9"5Ru, "9"6Ru(n,p)"9"6Tc"g, "9"6Ru(n,p)"9"6Tc"m, "1"0"4Ru(n,p)"1"0"4Tc, "1"0"2Ru(n,p)"1"0"2Tc"m, "1"0"4Ru(n,#alpha#)"1"0"1Mo, "1"0"2Ru(n,#alpha#)"9"9Mo, "9"6Ru(n,#alpha#)"9"3Mo"m, and "9"6Ru(n,d*)"9"5Tc"m. Results were discussed and compared with the previous works.

International Nuclear Information System (INIS)

In the context of sputtering experiments, studying the back-scattering of fast ion beams is a useful way to study inelastic ion-surface interactions, since then the trajectories and energies of the particles are well defined. This same argument holds for the scattering of fast molecular ions. We give a short account of our experiment where N"+_2 was scattered from a Ni(111) surface. The measured energy distributions of scattered N atoms are discussed with regard to vibrational and rotational energy transfer during scattering. (G.Q.).

Science.gov (United States)

An experimental study of H-air counterflow diffusion flames (CFDFs) is reported. Coaxial tubular

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

This study concerns mixtures of triacetone triperoxide (3,3,6,6,9,9-hexamethyl-1,2,4,5,7,8-hexoxonane, TATP) and ammonium nitrate (AN) with added water (W), as the case may be, and dry mixtures of TATP with urea nitrate (UN). Relative performances (RP) of the mixtures and their individual components, relative to TNT, were determined by means of ballistic mortar. The detonation energies, E_0, and detonation velocities, D, were calculated for the mixtures studied by means of the thermodynamic code CHEETAH. Relationships have been found and are discussed between the RP and the E_0 values related to unit volume of gaseous products of detonation of these mixtures. These relationships together with those between RP and oxygen balance values of the mixtures studied indicate different types of participation of AN and UN in the explosive decomposition of the respective ...

UK PubMed Central (United Kingdom)

We use high-density single nucleotide polymorphism (SNP) genotyping microarrays to demonstrate the ability to accurately and robustly determine whether individuals are in a complex genomic DNA mixture....Full Text Available

UK PubMed Central (United Kingdom)

Growth of the malolactic bacterium Leuconostoc oenos was improved with respect to both the specific growth rate and the biomass yield during the fermentation of glucose-malate mixtures as compared with...Full Text Available

Science.gov (United States)

...false Bromoacetone, methyl bromide, chloropicrin and methyl bromide or methyl chloride...193 Bromoacetone, methyl bromide, chloropicrin and methyl bromide or methyl chloride...b) Bromoacetone, methyl bromide, chloropicrin and methyl bromide mixtures,...

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

Esters of dihydric alcohols with alkenylphosphonic or alkenylphosphinic acids which are polymerizable by free radicals are described. They are combined with polymer binders, in particular water-soluble polymers, and photoinitiators forming free radicals to give photopolymerizable mixtures which are suitable for the production of photoresists and printing plates. The mixtures display low heat-sensitivity and have long shelf lives. (author) 1 tab.

Energy Technology Data Exchange (ETDEWEB)

The paper presents a compilation of data and model interpretation of CO{sub 2} with mixtures of amines. The data includes both absorption and desorption conditions in the 288-313K range. The combined mass transfer/equilibrium model can effectively represent CO{sub 2} mass transfer rates for the various mixtures under a wide range of conditions.

Energy Technology Data Exchange (ETDEWEB)

Two-phase flow, thermal management systems are currently being considered as an alternative to conventional, single phase systems for future space missions because of their potential to reduce overall system mass, size, and pumping power requirements. Knowledge of flow regime transitions, heat transfer characteristics, and pressure drop correlations is necessary to design and develop two-phase systems. This work is concerned with microgravity, two-phase flow regime analysis. The data come from a recent sets of experiments. The experiments were funded by NASA Johnson Space Center (JSC) and conducted by NASA JSC with Texas A M University. The experiment was on loan to NASA JSC from Foster-Miller, Inc., who constructed it with funding from the Air Force Phillips Laboratory. The experiment used R12 as the working fluid. A Foster-Miller two phase pump was used to circulate the two phase mixture and allow separate measurements of the vapor and liquid ...

Energy Technology Data Exchange (ETDEWEB)

Some properties of the remarkable Ti{sub 3}SiC{sub 2} based ceramic synthesised by hot pressing of elemental Ti, Si, and C powders have been investigated. Its flexural strength by using three point bending tests and fracture toughness by using single edge notched beam tests were measured at room temperature to be in the range 310-427 MPa and about 7.MPa m{sup 1/2}, respectively. This material is a relative 'soft' ceramic with a low hardness of 4 GPa. Ti{sub 3}SiC{sub 2} is similar to the soft metals and is a damage tolerant material that is able to contain the extent of microdamage. An oxidation test has been performed in the temperature range 1000-1400{sup o}C in air for 20 h. The oxidation resistance below 1100{sup o}C was good. Two oxidized layers were formed, the outer layer consisting of pure rutile-type TiO{sub 2}, and the inner layer a mixture of SiO{sub 2} and TiO{sub 2}. The average coefficient of thermal expansion ...

Science.gov (United States)

Polycyclic aromatic hydrocarbons (PAHs) are combustion products of organic materials, mixtures of which contain multiple known and probable human carcinogens. PAHs occur in indoor and outdoor air, as well as in char-broiled meats and fish. Human exposure to PAHs occurs by inhalation, ingestion and topical absorption, and subsequently formed metabolites are either rendered hydrophilic and excreted, or bioactivated and bound to cellular macromolecules. The formation of PAH-DNA adducts (DNA binding products), considered a necessary step in PAH-initiated carcinogenesis, has been widely studied in experimental models and has been documented in human tissues. This review describes immunohistochemistry (IHC) studies, which reveal localization of PAH-DNA adducts in human tissues, and semi-quantify PAH-DNA adduct levels using the Automated Cellular Imaging System (ACIS). These studies have shown that PAH-DNA adducts concentrate in: basal and supra-basal ...

Energy Technology Data Exchange (ETDEWEB)

The zinc-air battery/fuel cell is an old technology invented one hundred years ago. However, there is renewed interest in this technology in response to the growing need for clean energy technology. The zinc-air battery/fuel cell is more attractive than similar technologies because its characteristics include high power density, safe operation and storage, and low cost. Zinc-air battery/fuel cells can be made in milliwatts to mega watts to accommodate different applications. The zinc-air battery/fuel cell has four major designs, namely primary, mechanically rechargeable, continuous feed and electrically rechargeable zinc-air battery/fuel cells. Among the different designs, the most common is the air cathode. There are 3 generations of catalysts used in the air cathodes. This paper discussed the different designs of the ...

Science.gov (United States)

An organic inhibitor for acid corrosion inhibition is described. The inhibitor is a condensation product of a mixture of diethyl- and dibutyl-thiourea with hexamethylenetatramine. This condensation product is preferably made by reacting a mixture of diethyl- and dibutyl-thiourea, in a weight ratio of from 1:5 to 5:1, with 0.1 to 1 mole of hexamethylene tetramine per mole of the thiourea mixture, at temperatures of from 100 to 150 C. It is possible to modify this by using other organic thiourea derivatives containing organic radicals (aliphatic or aromatic) having up to 10 carbon atoms, for example, ditoluyl-thiourea, in addition to the mixture of diethyl- and dibutyl-thiourea, but the amount by weight of these other derivatives must not exceed 20% of the diethyl-dibutyl-thiourea mixture. The advantages of the inhibitor are observed mainly when it is used in hydrofluoric acid ...

International Nuclear Information System (INIS)

This paper proposes a model to explain tritium release behavior of an irradiated Li_4SiO_4 sample made by Forschungszentrum Karlsruhe. The release curves were obtained in a series of experiments carried out using out-pile temperature programmed desorption techniques in the Kyoto University Reactor (KUR). Tritium release curves obtained for different purge gas compositions (N_2, N_2 + H_2, N_2 + H_2O) were compared for selection of suitable conditions to determine the apparent diffusivity of tritium in a crystal grain of Li_4SiO_4.In the model formation, some mass transfer steps in the bulk of the crystal grain and those on the surface of the grain were taken into account, which were diffusion of tritium in the grain, adsorption and desorption of water on the surface of the grain, two types of isotope exchange reactions, and water formation reaction by the ...

International Nuclear Information System (INIS)

Using the ammonia (NH3) plasma generated by a helical antenna surrounded by two magnetic coils, the transition of the discharge mode from low-density plasma to high-density one was observed. At the transition, the emission intensities from the H atoms and NH radicals especially increased in the optical emission spectroscopy, while the intensities of the other emission lines also increased abruptly. The nitridation of gallium arsenide (GaAs) surface was performed using the high-density NH3 plasma, and the properties of the nitrided surface layer were compared with those nitrided by high-density N2 plasma using the same apparatus. From the spectroscopic ellipsometry measurements, the thickness of the nitrided layer was estimated to be 16-18 nm, while that by N2 was 3-4 nm. From the Ga 3d spectra, the contamination with oxygen in the nitridation layer by NH3 plasma was less than that by ...

International Nuclear Information System (INIS)

NaCl doped MgCl_2.nEtOH adducts were prepared by ball-milling MgCl_2.2.5EtOH with NaCl. Both the ball-milled MgCl_2.nEtOH/NaCl mixture and pure MgCl_2.2.5EtOH adducts were analyzed by X-ray diffraction (XRD), transmission electron microscope (TEM), thermogravimetry (TG) and differencial scanning calorimetry (DSC). A simple MgCl_2.nEtOH/NaCl mixture without ball-milling treatment was also studied for comparison. Two kinds of mixed crystals, Na_2MgCl_4 and NaMgCl_3, were found to be formed in a ball-milled mixture that contained 16 mol.% NaCl. TG and DSC analysis of the samples also provided indirect evidences supporting the presence of the mixed crystals in the ball-milled mixture. Adding certain amounts of NaCl in MgCl_2.2.5EtOH adduct, either by co-milling or by simple mixing, greatly increased the thermal stability of the adduct, but thermal decomposition behaviour of the ball-milled ...

Energy Technology Data Exchange (ETDEWEB)

The objectives of this study were to estimate symbiotic nitrogen fixation by two common pasture legumes, Trifolium subterraneum L. and Medicago truncatula Gaertn., and an Australian native legume, Acacia dealbata Link, growing in pots using an indirect isotopic method. This method was also used to calibrate the C2H2 reduction assay of the intact plants. In addition, hydrogen evolution was measured in an attempt to explain the variations in C2H2:N2 ratios between the species. 25 refs.; 1 figure; 4 tabs.

Energy Technology Data Exchange (ETDEWEB)

The nitrogen content of 10 medicinal plant species has been determined by fast-neutron activation analysis (FNAA). Correction factors for the effects of the /sup 16/O(p,..cap alpha..)/sup 13/N knock-on proton-induced reaction and the (n,2n) reactions, which produce interfering positron-emitting radionuclides, have also been determined. The total relative interference from the /sup 16/O(p,..cap alpha..)/sup 13/N and (n,2n) reactions of K, Cl, Fe and Br was found to be 5.1 to 32.1% for the plant samples.

International Nuclear Information System (INIS)

Differential scattering experiments are reported for proton impact on N_2, CO, and NO in the energy range E/sub lab/=30--80 eV. The measurements include the range of very small scattering angles around 0"0 as well as the rainbow region. The vibrationally resolved energy-loss spectra show a relatively low vibrational inelasticity for all three systems. Differential cross sections, transition probabilities, and the mean vibrational energy transfer are presented. Rotational excitation is indicated by the broadening of the energy-loss peaks which is most significant for H"+--NO. The small-angle scattering data for vibrational excitation in CO show good agreement with the impact parameter theory using the known long-range interactions for this system.

Energy Technology Data Exchange (ETDEWEB)

The effect of tsub(A) austenitization temperature in heating for quenching as well as in the cycle of high-temperature thermomechanical treatment (HTMT) on structure, mechanical properties and fracture mode of 40KhN2MA structural steel is investigated. It is shown that heating up to 1200 deg C does not affect essentially sigmasub(b) and sigmasub(0.2) of a quenched material but increases fracture toughness of 200 deg C - tempered precracked specimens and is accompanied by a decrease of impact strength and plasticity of vee-notched specimens. The optimum complex of mechanical properties is attained upon combined treatment comprising heating up to 1200 deg C and HTMT with deformation at 850 deg C.

Science.gov (United States)

We report the characteristics of visible vertical cavity surface emitting laser diodes. Wafers are grown such that the Fabry--Perot resonance wavelength changes with position from 690 to 620 nm, overlapping to varying degrees with the [ital n]=1 and [ital n]=2 quantum well gain peaks at [similar to]670 and 650 nm. Gain guided devices are tested across the entire wafer, and pulsed room temperature lasing is observed from 634.6 to 663.2 nm. Our results suggest that gain contributions from the second quantized state are required to overcome high cavity losses in order to achieve lasing.

Energy Technology Data Exchange (ETDEWEB)

This guidebook concerns the design of air-conditioning and air-treatment installations in recent and old buildings. The design of indoor atmosphere treatment systems is based on a rigorous and safe methodology. The following aspects are reviewed: situation of ambient air treatment, different aspects of a project, humid-air technique, principles of air treatment, basic conditions for a successful project, determination of enthalpy and hydric loads of rooms, design of ambient treatment systems, cold water production using a thermodynamical system, aeraulics, hydraulics, acoustics, logics of operation, forecasting of energy consumptions, global management of air-conditioning installations, ambient air-treatment systems. (J.S.)

Energy Technology Data Exchange (ETDEWEB)

Gas turbine component protection remains essential but environmental regulations emphasize the gas-turbine efficiency. Heating and cooling are features often integrated into the GI air intake packages to provide the optimum operating conditions. This paper describes modern inlet air treatment systems and discusses their effectiveness. (author)

UK PubMed Central (United Kingdom)

Studies of the associations between air pollution and hospital admissions and emergency room use are reviewed, including studies of air pollution episodes, time-series analyses, and cross-sectional...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The measurement of air pollutants is no more sufficient. It is necessary to assess the risk induced by air pollution, and then to put in place actions to reduce it. The air quality monitoring takes into account different pollutants: nitrogen oxides, carbon monoxide, particulates for the traffic; sulfur dioxide and particulates for use of fuel or coal or chemical transformations in air; ozone and nitrogen dioxide from hydrocarbon and nitrogen oxides emissions; the use of simulation methods allow to calculate the concentrations levels for these pollutants taken as indicators. (N.C.)

Energy Technology Data Exchange (ETDEWEB)

The key component for improving the energy efficiency and cycle life of the electrically rechargeable zinc-air battery is the bifunctional air electrode. The air electrodes described in this paper contained different types of carbon black as the substrate for the perovskite catalyst (La{sub 0.6}Ca{sub 0.4}CoO{sub 3}). Morphological and physical properties of the carbon substrates play an important role in enhancing the activity and stability of the bifunctional air electrode. Current-potential curves and cycle-life tests were applied in order to gather information on the activity and stability of these electrodes. (authors)

International Nuclear Information System (INIS)

Excitation functions, production yields and radionuclidic purities are described for "2"0"1Tl production by the "2"0"3Tl(p,3n) "2"0"1Pb #-># "2"0"1Tl and "2"0"5Tl(p,5n)"2"0"1Pb#->#"2"0"1Tl nuclear reactions. The yields (mCi g"-"1 cm"2/#mu#A-hr) of the parent "2"0"1Pb(9.4hr), as well as the radiocontaminants "2"0"0Pb(21.5hr), sup(202m)Pb(3.62 hr), "2"0"3Pb(52.1 hr) and sup(204m)Pb(1.115 hr) were measured by irradiating a stack of thin natural Tl foils with protons from the 76-in isochronous cyclotron at the Crocker Nuclear Laboratory. The "2"0"1Tl thick-target yield (mCi/#mu#A hr) was calculated for different target thicknesses and corresponding incident proton energies. The excitation functions for the "2"0"3Tl(p,3n)"2"0"1Pb and "2"0"5Tl(p,5n)"2"0"1Pb reactions were measured in the 15-60-MeV energy range. (author).

International Nuclear Information System (INIS)

We propose and construct a new type of extended superconformal algebra (ESA) based on the super Toda field theory. Both in the N = 1 ESA and in the N = 2 ESA, an arbitrary value of the central charge is allowed in contrast with the previously known super W-algebra. The generators of ESA are interpreted as the constants of motion in the super Toda field theory. (orig.).

International Nuclear Information System (INIS)

In this contribution we compare the electron scattering processes observed in pure O_2 clusters and mixed clusters like O_2/Ne, O_2/Ar and O_2/N_2. The overlap and positions of the potential curves of O_2 states show the different possible electron attachment processes and also explain the formation of O_2 in clusters. (author).

Science.gov (United States)

Engine flow simulation was provided by four separately mounted air ejectors connected to a high-pressure air supply. The engine nacelle center lines were ...

Science.gov (United States)

... Title : The Numerical Weather Prediction System at the Italian Air Force Weather Service: Impact of Non-Conventional Observations and Increased ...

Wastenet

...Air Quality Monitoring Networks Products and Equipment Find and compare a variety of air quality monitoring networks products and equipment on the world's largest environmental industry portal. ...

Science.gov (United States)

... Army, Navy, Air Force Procedures (JANAP) 128 AUTODIN Operating Procedures. ... JANAP = Joint Army, Navy, Air Force Procedures ...

Energy Technology Data Exchange (ETDEWEB)

A new prototype model system named AirGIS has been developed to support local authorities in air quality management for big Danish cities. The system is based on the Danish operational street pollution model (OSPM), technical and cadastral digital maps and Danish national administrative databases on buildings, cadastres and populations. It applies a geographic information system (GIS). AirGIS estimates ambient air pollution levels at high temporal and spatial resolutions. The model system enables mapping of traffic emissions, air quality levels and human exposures at residence addresses, at workplace addresses and in streets. Mapping and scenario results can be compared with air quality limits. Impact assessment of traffic air pollution abatement measures can also be carried out. (author)

Energy Technology Data Exchange (ETDEWEB)

Many attempts have been made to generate reliable thermodiffusion coefficient models for binary mixtures. This paper presented a simple analytical model for the prediction of thermal diffusion coefficients in linear chain hydrocarbon binary mixtures using the thermodynamics of irreversible process. More specifically, the model represented the net heat transport, or the energy of detaching a molecule from its neighbours in the region of the binary mixture minus the energy given up in that region when one molecule fills a hole, and examined its accuracy by comparing theoretical results with available experimental data for linear chain hydrocarbon binary mixtures. The new model was based on phenomenological and kinetic approaches which have been found to be the most reliable. The paper discussed the net heat of transport for each component in the binary mixtures and presented the ...

Energy Technology Data Exchange (ETDEWEB)

Carbon capture and storage have been receiving increasing interest lately, mainly as an option to reduce CO{sub 2} emissions from the power sector. The concept could be adapted for production of H{sub 2} as well, which would provide a carbon free energy carrier that could be used for example as transportation fuel. In this doctoral thesis, the option to use chemical-looping technologies to produce H{sub 2} from fossil fuels with CO{sub 2} capture is explored. In chemical-looping combustion, direct contact between fuel and combustion air is avoided. Instead, a solid oxygen carrier performs the task of bringing oxygen from the air to the fuel. Thus, the resulting CO{sub 2} and H{sub 2}O are not diluted with N{sub 2}, and pure CO{sub 2} can easily be recovered by cooling and condensation. The heat of reaction is the same as for ordinary combustion. Chemical-looping reforming uses the same basic principles as chemical-looping combustion, but ...

Science.gov (United States)

The MISR instrument aboard NASA's Terra satellite participated in the UAE-2 campaign, August-October 2004. This campaign represented a unique opportunity to study the complex aerosol situation in the Arabian Gulf region, in the context of a first-rate collection of aircraft and surface-based instruments, giving us the opportunity to do some groundbreaking satellite aerosol validation work. We aimed (1) to validate MISR aerosol retrieval results for dust and pollution particles over dark and light surfaces, and (2) to contribute regional maps of aerosol optical thickness (AOT) and particle micro-physical properties, giving spatial context to the field-instrument measurements, and moving toward a satellite-based regional aerosol climatology. The validation effort benefited from the combination of an instrumented aircraft and a regional network of surface-based sun photometers. We obtained high-quality sub-orbital data coincident with MISR overpasses on three days: September 01, 10, and ...

Energy Technology Data Exchange (ETDEWEB)

The shifts induced by equimolar mixture of typical lanthanide shift reagent such as 2,2-dimethyl-6,6,7,7,8,8,8-heptafluoro-3,5-octadionato europium with silver trifluoroacetate in /sup 1/H NMR spectra of aromatic hydrocarbons have been used for analytical purposes; the NMR determination of m- and p-xylenes in mixtures has been chosen as an example. The use has been made of the difference between induced shifts of methyl group signals in the /sup 1/H NMR spectra of m- and p-xylenes. The magnitude of induced shifts of methyl groups signal in m-xylene is always larger than that of p-isomer, irrespective of contents of m- and p-xylenes in mixture.

UK PubMed Central (United Kingdom)

A binary mixture of imipramine HCl and chlordiazepoxide was determined by three different spectrophotometric methods. The first method involved determination of imipramine HCl and chlordiazepoxide using...Full Text Available

Science.gov (United States)

... The phenol and cresylic acid stream is flashed in a thin film evaporator over a concentrated sulfuric acid mixture to remove pyridine type substances ...

Energy Technology Data Exchange (ETDEWEB)

The passivity and breakdown of passivity of 1018 carbon steel in propylene carbonate (PC) and 1,2-dimethoxyethane (DME) mixtures with 0.5 molar lithium hexafluoroarsenate supporting electrolyte were examined via several electrochemical and surface analytical methods. The PC-DME/0.5 M LiAsF{sub 6} mixtures ranged from 10 to 90 mol % PC. The results from the PC/DME mixtures were compared to passivating mechanisms found in pure PC and DME solutions. In PC-rich mixtures, the breakdown of passivity occurred near the oxidation potentials of either organic solvent. Premature breakdown of the carbon steel in PC-DME mixtures occurred at sulfide inclusions as was observed earlier in PC/0.5 M LiAsF{sub 6} solutions although passive films attempted to form at these inclusion sites in mixtures containing at least 10 mol % DME. As the DME content increased in the PC-DME ...

Energy Technology Data Exchange (ETDEWEB)

Molar excess volumes, V/sup E/, and molar excess enthalpies, H/sup E/, have been determined at 298.15 K by using dilatometer and an LKB flow microcalorimeter, respectively, for benzene (A), toluene (A), o-xylene (A), m-xylene (A), or rho-xylene (A) + o-chlorotoulene (B) mixtures. While both the V/sup E/ and the H/sup E/ values are positive for benzene (A) = o-chlorotoluene (B) mixtures, they are negative for the rest of the binary mixtures. The data have also been compared with the available literature values.

International Nuclear Information System (INIS)

A method is described for immobilizing or solidifying waste material, which includes blending the waste material with powdered metal and subjecting the mixture of waste material and powdered metal to high pressure. (author).

Energy Technology Data Exchange (ETDEWEB)

Apparatus and method are described for the vaporization of liquid fuel oils to produce a gaseous mixture suitable for burning in a burner normally designed for operation utilizing natural gas.

British Library Electronic Table of Contents (United Kingdom)

The effects of five extraction solvents and their mixtures on the yield of metabolites in crude and fractionated extracts of Annona muricata L. leaves were investigated by direct comparison. Extraction media were prepared using simplex centroid mixtures of ethanol, ethyl acetate, dichloromethane, acetone, and chloroform. The effects of the mobile phase solvent strength and the analysis wavelength on the chromatographic separation were also investigated. Solvent mixtures rather than pure solvents were found to be the most efficient extractors for the different fractions. The results indicated that the mobile phase composed of methanol/acetonitrile/water (26:27:47 v/v/v) was most suitable for the basic fraction analysis at 254 nm, whereas the mobile phase composed of methanol/acetonitrile/wa...

International Nuclear Information System (INIS)

AISI 5140 steel was plasma nitrided at various gas mixtures of nitrogen, hydrogen, and argon to investigate the actions of hydrogen and argon on plasma nitriding. The structural and mechanical properties of ion-nitrided AISI 5140 steel have been assessed by evaluating composition of phases, surface hardness, compound layer thickness, and case depth by using X-ray diffraction (XRD), microhardness tests, and scanning electron microscopy (SEM). It was found that the growth of compound layer can be controlled and the diffusion improved when the gas mixture includes H_2 gas. Additionally, it was determined that the amount of Ar in dual gas mixture must be at 20% minimum to obtain distinctive surface hardness and compound layer thickness.

Energy Technology Data Exchange (ETDEWEB)

Fhe ECOTRONIC system developed by Bosch und Pierburg System oHG is an electronic system for mixture formation for Otto-cycle engines complying with high operational requirements. Engineers incorporated electronic control of the quantity of mixture and mixture enrichment for supplementary functions into a reliable, low-cost system, which will also comply with future requirements concerning fuel consumption, emissions and driveability. The author of the present article reduces the carburetor down to its basic systems, explains how supplementary functions were converted from mechanical to either open or closed-loop electronic control, and describes the newly developed actuators, the control unit making use of digital technology, and the results achieved.

British Library Electronic Table of Contents (United Kingdom)

Summary Although risk assessments are typically conducted on a chemical-by-chemical basis, the 1996 Food Quality Protection Act required the US Environmental Protection Agency to consider cumulative risk of chemicals that act via a common mechanism of toxicity. To this end, we are conducting studies with mixtures of chemicals to elucidate mechanisms of joint action at the systemic level with the goal of providing a framework for assessing the cumulative effects of reproductive toxicants. Previous mixture studies conducted with antiandrogenic chemicals are reviewed briefly and two new studies are described. In all binary mixture studies, rats were dosed during pregnancy with chemicals, singly or in pairs, at dosage levels equivalent to approximately one-half of the ED50 for hypospadias or e...

International Nuclear Information System (INIS)

Russian (Jan 1978). USSR Chorna, IM Beshta, EI Kvitkovskij, LN L'vovskij

Energy Technology Data Exchange (ETDEWEB)

(Boiling site densities and heat-transfer coefficients have been measured for ethanol-water and ethanol-benzene mixtures at 1.01 bar for a heated vertical brass disk. A strong effect of composition on the boiling site density was observed, which was attributed to the nature of the activation of the boiling surface and mass diffusion effects. The boiling heat-transfer coefficient was found to decrease with increasin subcooling, but for the mixtures at a given level of subcooling the decrease was less than that for the single components and azeotropic mixtures.) The heat-transfer coefficient at a given heat flux was seen to be quite insensitive to the very large increase in boiling site density in comparing the pure water and the ethanol-water azeotrope results, leading one to question pool boiling models that predict heat-transfer rates on the basis of boiling site density.

Energy Technology Data Exchange (ETDEWEB)

Because of good thermal insulation of advanced energetic buildings and their good airtightness the air hygiene is insufficient. A normal ventilation behaviour by window opening consumes too much heating energy. A calculation method is shown taking into account a required air change number, flow rate and indoor air quality as thermal comfort in the rooms occupied by different number of persons. (GL)

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

International Nuclear Information System (INIS)

Short communication. 1 fig.

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

Science.gov (United States)

... 14 Face Detection ..... 14 Automated Mapping ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

The report examines common ventilation and air conditioning systems and strategies for both domestic and commercial buildings; and covers issues such as energy conservation, indoor air quality and occupant comfort. Drawing data from many countries in Europe and the United States of America, various natural, mechanical and air conditioning systems were compared using criteria such as climate, level of occupant interaction, and level of system comfort. This classification system is evaluated and seen as a valuable framework for further research. (U.K.)

Energy Technology Data Exchange (ETDEWEB)

The ventilation performance of cold-air distribution systems was investigated in a full-scale test room for three different designs of ceiling-mounted diffusers: a large square radial, a small square radial, and two linear diffusers. The supply air temperature was 38 F (3.3 C). Tests were conducted with internal heat loads and with and without furnishings. The local mean ages of air, air diffusion effectiveness, and contaminant-removal efficiency were measured using tracer gas techniques to assess the performance of the ventilation system in maintaining adequate air quality conditions in the occupied region. Air velocities and temperatures were also measured in the occupied region to calculate the air diffusion performance index (ADPI). It was found that the cold-air distribution system provided satisfactory ...

Science.gov (United States)

This report describes an investigation of the performance of air-augmented waterjet thrusters. The investigation is divided into two parts. Part one describes a study of the injection of large diameter air bubbles to reduce heat transfer between the air and water and, thus, increase the thrust. This study is done analytically by solving the appropriate, governing equations. The results indicate that the approach is very worth-while since thrust can be increased ten percent as compared to air-augmentation with small bubbles. Several practical systems are discussed for injecting large air bubbles. Part two is an experimental investigation of the thrust produced under a wind range of conditions. The results show that a thrust increase of more than 20 percent can be achieved by air-augmentation. Further, the performance improves for larger thrust nozzles.

Energy Technology Data Exchange (ETDEWEB)

By means of a numerical simulation model (PHOENICS) the air flow and the distribution of the air concentration in an operating room of an hospital have been calculated. Comparisons were made for 11 different conditions (m[sup 3]/h air flow, speed of the air supply in the centre, the middle and outside of the room), of which six cases are discussed in this article, in order to optimize the air flow pattern in the room. The calculations were conducted for the so-called Howorth system. It is shown that the inlet velocity profile with a higher inlet velocity in the center zone of the hood gives the best results. The calculated results were validated by some measurements and experiments with smoke. 7 figs., 2 tabs., 8 refs.

Energy Technology Data Exchange (ETDEWEB)

The aim of this research is to experimentally study the efficiency of a new-design plate collector used to heat air in a new desalination humidification-dehumidification process. In fact, in such processes, the air solar collectors work at unusual experimental parameters (forced convection, elevated air humidity, high solar irradiation). At these stressed experimental conditions, few published works are available in literature. Furthermore, the comparison of the efficiency of collectors running with normal air humidity content (about 10-20 g kg{sup -1}) and air of elevated humidity (20-50 g kg{sup -1}) have not been published to our knowledge. In the present investigation, a new air solar plate collector was designed and developed for its use in a desalination process. Moreover, a characterization of such collector was performed under different experimental ...

International Nuclear Information System (INIS)

The main purpose of this work is to evaluate the role of CT in identifying other morphological signs of met static lymph node involvement from non small cell bronchogenic carcinoma. This is done to improve N staging, a critical step in this disease. In fact, since diameter is the only criterion used to distinguish normal form abnormal lymph nodes, mediastinal CT only has 80% diagnostic accuracy. 137 patients with known or suspected lung cancer were examined with Helical CT during early and late arterial phases (2 min. delay, 3 mm thickness, 5 mm inter slice gap) to depict node characteristics. Mediastinal lymph nodes, located according to the American Thoracic Society mapping, were considered normal when they were not visible or, if visible, less than 1 cm in diameter and of homogeneous density; lymph nodes over 1 cm in diameter and homogenous density were considered reactive. A lymph node was considered metastatic when, independent of size, the following signs were found: central hypo ...

Energy Technology Data Exchange (ETDEWEB)

The electrolyte was brought into contact with air and potassium carbonate was measured with various contact time in order to check the defect of carbon dioxide in the air on zinc-air cell. The relationship between potassium carbonate concentration in electrolyte and battery capacity was also studied. The potassium carbonate concentration in the electrolyte. The rate of carbon dioxide absorption was mainly affected by the pore size of hydrophobic membrane. Our study showed that adapting the pore of hydrophobic membrane decreased the loss of cell discharge performance due to the presence of carbon dioxide or water vapor in the atmosphere. 7 refs., 12 figs., 1 tab.

International Nuclear Information System (INIS)

Thermodynamic consideration and process calculations at equilibrium conditions showed that processes for separating gas mixtures by partial condensation at low temperatures using turboexpanders have got less energy losses than processes with quasi isobar partial condensation. Compared to the low-pressure parts of condensing steam turbines in turboexpanders less erosion problems are to expected for such separating processes. Separation of liquid in the machine, however, is more difficult withouf additional measures. (orig.).

Energy Technology Data Exchange (ETDEWEB)

A multiple metal oxide sorbent supported on a zeolite of substantially silicon oxide is used for the desulfurization of process gas streams, such as from a coal gasifier, at temperatures in the range of about 1200.degree. to about 1600.degree. F. The sorbent is provided by a mixture of copper oxide and manganese oxide and preferably such a mixture with molybdenum oxide. The manganese oxide and the molybdenum are believed to function as promoters for the reaction of hydrogen sulfide with copper oxide. Also, the manganese oxide inhibits the volatilization of the molybdenum oxide at the higher temperatures.

CERN Document Server

The Rayleigh scattering length has been calculated for rare-gas liquids in the ultraviolet for the frequencies at which they luminesce. The calculations are based on the measured dielectric constants in the gas phase, except in the case of xenon for which measurements are available in the liquid. The scattering length mayplace constraints on the design of some large-scale detectors, using uv luminescence, being proposed to observe solar neutrinos and dark matter. Rayleigh scattering in mixtures of rare-gas mixtures is also discussed.

British Library Electronic Table of Contents (United Kingdom)

Results are given of numerical simulation of three-dimensional pattern of flow of a two-phase steam-water mixture in the house of a PGV-1000 horizontal steam generator obtained using the BAGIRA best-estimate thermohydrodynamic computer codes. The space distributions of velocities and local void fractions in the steam generator housing for different modes of operation of power-generating unit are calculated and compared with available experimental data.

International Nuclear Information System (INIS)

A mathematical and physical model was constructed describing the hydrodynamics of the two-phase mixture in the horizontal steam generator. The HP 9830 A desk-top calculator was used for the computations. The output variable of the solution was the level shape. A quantitative and qualitative comparison was made of the results of computations and experimental data. (author).

Energy Technology Data Exchange (ETDEWEB)

The explosive known under the name Saletrol (mixture of ammonium nitrate and hydrocarbon fuel or a mixture of ammonium nitrate, hydrocarbon fuel and aluminum powder) is characterized by the absence of physical stability during storage (the oily fluid flows from the upper layers of the explosive downward) and as a consequence of this, decrease in the required effectiveness of blasting and increased release of toxic gaseous blasting products. In order to eliminate this shortcoming, lightening clay is added to Saletrol in a quantity of 3-12% by weight of the total explosive mass.

Energy Technology Data Exchange (ETDEWEB)

Repeated exposure to cold air reduces the metabolic response to cold air exposure in man. The purpose of this investigation was to measure the change in resting metabolic rate (RMR) with exposure to 22C air and 4C air during a 12 day period. Four women sat in 22C air for 45 min followed by 45 min in 4C air each day for ten days. The authors measured RMR during a 45 min period in 22C air followed by 45 min in 4C air on four days. All subjects began their morning exposures on a Monday within 2 days of the onset of menses completing the study on a Friday, 12 days later. Subjects dressed in a T-shirt, shorts and cotton socks. During 45 min of exposure to warm air, RMR remained steady at 10% of VO{sub 2peak} on Day 1 and 10% on Day 5. RMR during exposure to warm air significantly ...

Energy Technology Data Exchange (ETDEWEB)

The Flory model is applied to predict the isobaric expansion coefficients, {alpha}{sub P}, isentropic, {kappa}{sub S}, and isothermal, {kappa}{sub T}, compressibilities and speeds of sound, u, of the highly complex mixtures: hydroxyether + alkane, + dibutylether, + 1-butanol or + 2-methoxyethanol, 1-alkanol + alkane, and 1-alkanol + dibutylether. Predictions were obtained using the energetic parameter, {chi}{sub 12}, determined from values of excess enthalpies, H{sup E}, and from values of the excess isochoric internal energies, U{sub V}{sup E}, at equimolar composition. No meaningful differences exist between such predictions. Deviations between experimental and calculated values are lower than 2% for mixtures containing alkoxyethanols. Poorer results are obtained for 1-alkanol + dibutylether mixtures with deviations up to 5%. It is shown that predictions on {alpha}{sub P}, {kappa}{sub S}, {kappa}{sub T}, and u essentially ...

Energy Technology Data Exchange (ETDEWEB)

The characteristics of diesel fuel jet atomization in carburetors depend on dynamic viscosity (v) density (d) and surface tension (st) of fuel, grouped in the combined functions v/d; st/v and st/d. Values of these combined functions for binary mixtures of a farm diesel fuel with a crude vegetable oil (sunflower, soybean, cotton and foot-cake olive oils) as well as with a used frying olive oil, are calculated. Three different diesel fuels have been studied. Combined function values of these mixtures are influenced by the characteristics of their diesel fuel. Mixtures containing less than 24% of any studied crude oils show kinematic viscosity values at 40 degrees C not exceeding 5.8 squared millimeters/s. This value is the higher limit for typical United States farm diesel fuels, according to specifications of the Cummins Engine Company. Mixture with 21% of the used frying olive oil shows at 40 degrees C ...

International Nuclear Information System (INIS)

The preparation of wood-plastic combinations (WPC) using combined methods for curing intermediate products and final products is described. In the first step, impregnated wood was irradiated using doses of 1 to 10 kGy in the presence of chemical initiators of polymerization. Thereafter, curing of this partly cured impregnating mixture was accomplished in the wood at elevated temperatures with the aid of chemical initiators of polymerization. Impregnation mixtures based on unsaturated polyester resins and methyl methacrylate, and the wood species European Beech (Fagus silvatica) and Black Alder (Alnus glutinosa) were used. The results indicate that this method of preparing WPC allows substantially lower radiation doses to be used, i.e., doses in the range of 1 to 2.5 kGy. These doses gelatinate the impregnation mixture in the wood so that the subsequent curing by chemical polymerization initiators proceeds without the ...

Science.gov (United States)

New tetradentate N(2)O(2) donor Schiff bases and their mononuclear Co(II), Ni(II), Cu(II), and Pd(II) complexes were synthesized and characterized extensively by IR, (1)H-, (13)C-NMR, mass, ESR, conductivity measurements, elemental and thermal analysis. Specifically the magnetic and electronic spectral measurements demonstrate the octahedral structures of cobalt(II), nickel(II) complexes and square planar geometries of copper(II), palladium(II) complexes. All the ligands and complexes were screened for their in vitro antibacterial activity against two gram-positive bacteria (Bacillus subtilis, Staphylococcus aureus) and two gram-negative bacteria (Escherichia coli, Klebsiella pneumonia). In this study, Pd(II) complexes exhibited potent antibacterial activity against B. subtilis, S. aureus whereas other metal complexes also exerted good activity towards all tested strains even than standard drugs streptomycin and ampicillin. PMID:21297294

British Library Electronic Table of Contents (United Kingdom)

The aim of this pilot study was to evaluate the feasibility of long-term subcutaneous application of low-dose IL-2 in children with malignancies at very high risk of relapse who underwent highly T cell and B cell depleted HLA-identical (MUD) or full haplotype mismatched related hematopoetic stem cell transplantation. We studied 11 patients with acute leukemias/myelodysplastic syndrome and juvenile myelomonocytic leukemia (active disease and/or second stem cell transplantation, n = 8; >=CR 2, n = 2) and relapsed or progressive Ewings sarcoma (n = 2) who received prophylactic IL-2 treatment for a high probability of disease recurrence after allo-HSCT. Toxicities from IL-2 were transient fever, fatigue and local inflammation. In one patient GvHD grade III with no clear association to IL-2 adm...

International Nuclear Information System (INIS)

In this experiment, a Si wafer containing four lightly doped B marker layers epitaxially grown by CVD has been implanted with 100 keV Si"+ ions to a dose of 2 x 10"1"4 ions/cm"2 and annealed at 850 deg. C for several times in an RTA system in flowing N_2. TEM and SIMS analysis, in conjunction with a transient enhanced diffusion (TED) evaluation method based on the kick-out diffusion mechanism, have allowed us to accurately study the boron TED evolution in presence of extended defects. We show that the silicon surface plays a key role in the recombination of Si interstitial atoms by providing the first experimental evidence of the resulting Si_i_n_ts supersaturation gradient between the defect region and the surface. Our results indicate an upper limit of about 200 nm for the surface recombination length of Si interstitials at 850 deg. C in a N_2 ambient.

Science.gov (United States)

t5I gU9S y`xmRv A'b9 (RW$ F]>H ?ts6@ Snnl yHl$- #|t_C 6G8@ u,H8 3($ds #~^iy { aN2s VFR@1 zs|9n] %pyNv Z{+; !C 1cs= ||8_ 6r$0j n9X 8n`@ ,FH8S hg3` TBq*p UP09 ...

Energy Technology Data Exchange (ETDEWEB)

Purpose: To evaluate the success rates of the implantation of stent grafts in the treatment of peripheral aneurysms. Materials and methods: in 13 patients with 15 aneurysms at the common iliac artery (n = 6), external iliac artery (n = 1), hypogastric artery (n = 2), femoral artery (n = 2) or popliteal artery (n = 4), implantation of dacron-covered nitinol stents was performed. The patients were followed up for three to 20 months (mean, 8.8 months) with intravenous digital subtraction angiography, CT or colour-coded Doppler sonography. Results: In all cases, the aneurysm was successfully occluded after stent implantation. In one case with a popliteal aneurysm, kinking of the vessel caused thrombosis of the stent. The stent was successfully reopened. The aneurysm however, had to be surgically treated 9 months later. The primary and secondary patency rates at 6 months were 93% and 100%, respectively. ...

International Nuclear Information System (INIS)

Recent work on N=2 supersymmetric Bianchi type IX cosmologies coupled to a scalar field is extended to a general treatment of homogeneous quantum cosmologies with explicitly solvable momentum constraints, i.e., Bianchi types I, II, VII, VIII in addition to the Bianchi type IX, and special cases, namely, the Freidmann universes, the Kantowski-Sachs space, and Taub-NUT space. In addition to the earlier explicit solution of the Wheeler-DeWitt equation for Bianchi type IX, describing a virtual wormhole fluctuation, an additional explicit solution is given and identified with the ''no-boundary state.''.

International Nuclear Information System (INIS)

Mass distributions of fragments in the low-energy fission of nuclei from "1"8"7Ir to "2"1"3At have been analysed. This analysis has shown that shell effects in symmetric-mode fragment mass yields from the fission of pre-actinide nuclei could be described if one assumes the existence of two strongly deformed neutron shells in the arising fragments with neutron numbers N_1#approx#52 and N_2#approx#68. A new method has been proposed for quantitatively describing the mass distributions of the symmetric fission mode for pre-actinides with A#approx#180-220. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The present invention provides a compound of the formula (Cat).sup.+.sub.z[M.sup.++(5-nitro-1H-tetrazolato-N2).sup.-.sub.x(H.sub.2- O).sub.y] where x is 3 or 4, y is 2 or 3, x+y is 6, z is 1 or 2, and M.sup.++ is selected from the group consisting of iron, cobalt, nickel, copper, zinc, chromium, and manganese, and (Cat).sup.+ is selected from the group consisting of ammonium, sodium, potassium, rubidium and cesium. A method of preparing the compound of that formula is also disclosed.

International Nuclear Information System (INIS)

In this study, Multi-Walled Carbon Nanotubes (MWCNTs) / Hydroxylapatite (HAp) composites were made to improve mechanical properties by using Spark Plasma Sintering (SPS) method. Slurry 6 mol of CaHPO4#centre dot#2H2O (DCPD), 4 mol calcium hydroxide and MWCNTs were mixed and sintered by using SPS at 5-120 MPa pressure, 1200-1250 deg. C and in vacuum or N2 atmosphere. The fracture toughness of sintered MWCNTs/HAp composites was increased.