WorldWideScience

Sample records for molecular iodine-epoxy paint

  1. Study of molecular iodine-epoxy paint mass transfer

    Energy Technology Data Exchange (ETDEWEB)

    Belval-Haltier, E [Inst. de Protection et Surete Nucleaire, IPSN, CEN Cadarache, St. Paul-lez-Durance (France)

    1996-12-01

    The mass transfer phenomena may have a significant influence on the quantity of I{sub 2} which could be released following a severe accident of a nuclear power plant and specially the mass transfer of iodine onto containment surfaces. So, the objective of the present work was to evaluate which phase limited the adsorption process of iodine onto gaseous epoxy paint under a range of conditions which may be relevant to a severe reactor accident. In this aim, a series of experiments was conducted in which the sorption kinetics of molecular iodine, labelled with {sup 131}I, was measured by monitoring continuously the accumulation of this species on the epoxy surface. For each test condition, the initial deposition velocity was determined and the corresponding gas phase mass transfer, kg, was estimated by using the heat transfer analogy for a laminar flow passing over a flat plate. Then, the surface reaction rate, Kr, was deduced from these two values. Experiments performed indicated that iodine adsorption onto epoxy paint is highly dependent on temperature, relative humidity of the carrier gas and moisture content of the painted coupon. In dry air flow conditions, the adsorption of iodine onto paint was found to increase with temperature and to be limited by the surface reaction rate, Kr. The I{sub 2} adsorption rate was found to increase with the humidity of carrier gas and in some studied conditions, the initial deposition velocity appeared to be controlled by gas phase mass transfer rather than surface interaction. The same phenomenon has been observed with an increase of the initial water content of the painted coupon. (author) 6 figs., 1 tab., 8 refs.

  2. A FTIR/chemometrics approach to characterize the gamma radiation effects on iodine/epoxy-paint interactions in Nuclear Power Plants

    Energy Technology Data Exchange (ETDEWEB)

    Colombani, Juliette, E-mail: juliette.colombani@irsn.fr [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES/SEREX/L2EC, CEN Cadarache BP3, 13115 Saint Paul lez Durance Cedex (France); Chauvet, Elodie [Institut de Radioprotection et de Sûreté Nucléaire, PSN-RES/SEREX/L2EC, CEN Cadarache BP3, 13115 Saint Paul lez Durance Cedex (France); Aix-Marseille Université, CNRS ICR UMR 7273, 13397 Marseille Cedex 20 (France); Amat, Sandrine; Dupuy, Nathalie [Aix-Marseille Université, CNRS, IRD, Avignon Université, IMBE UMR 7263, 13397 Marseille Cedex 20 (France); Gigmes, Didier [Aix-Marseille Université, CNRS ICR UMR 7273, 13397 Marseille Cedex 20 (France)

    2017-04-01

    The effects of radiation on polymeric materials are a topic of concern in a wide range of industries including the sterilization, and the nuclear power industry. While much work has concentrated on systems like polyolefins that are radiation sterilized, some work has been done on epoxy systems. The epoxy system studied is an epoxy/amine paint which is representative of the paint that covers the inner surfaces of the French nuclear reactor containment buildings. In case of a severe accident on a Nuclear Power Plant, fission products can be released from the nuclear fuel to the reactor containment building. Among them, volatile iodine (I{sub 2}) can be produced and can interact with the epoxy-paint. This paint is also subjected to gamma radiation damages (due to the high dose in the containment coming from radionuclides released from the fuel). So the epoxy-paint studied was exposed to gamma radiation under air atmosphere after being loaded with I{sub 2} or not. The aim of this study is to characterize by FTIR spectroscopy the iodine-paint interactions, then to identify the radiation damages on the epoxy-paint, and to check their effects on these iodine-paint interactions. This work shows the potential of multi-block analysis method (ANOVA-PCA and COMDIM = AComDim) for such a study as it allows to identify the nature of iodine/epoxy-paint interactions and to characterize the gamma radiation damages on the epoxy-paint. AComDim method conduces to the extraction of Common Components to different tables and highlights factors of influence and their interactions.

  3. A FTIR/chemometrics approach to characterize the gamma radiation effects on iodine/epoxy-paint interactions in Nuclear Power Plants.

    Science.gov (United States)

    Colombani, Juliette; Chauvet, Elodie; Amat, Sandrine; Dupuy, Nathalie; Gigmes, Didier

    2017-04-01

    The effects of radiation on polymeric materials are a topic of concern in a wide range of industries including the sterilization, and the nuclear power industry. While much work has concentrated on systems like polyolefins that are radiation sterilized, some work has been done on epoxy systems. The epoxy system studied is an epoxy/amine paint which is representative of the paint that covers the inner surfaces of the French nuclear reactor containment buildings. In case of a severe accident on a Nuclear Power Plant, fission products can be released from the nuclear fuel to the reactor containment building. Among them, volatile iodine (I 2 ) can be produced and can interact with the epoxy-paint. This paint is also subjected to gamma radiation damages (due to the high dose in the containment coming from radionuclides released from the fuel). So the epoxy-paint studied was exposed to gamma radiation under air atmosphere after being loaded with I 2 or not. The aim of this study is to characterize by FTIR spectroscopy the iodine-paint interactions, then to identify the radiation damages on the epoxy-paint, and to check their effects on these iodine-paint interactions. This work shows the potential of multi-block analysis method (ANOVA-PCA and COMDIM = AComDim) for such a study as it allows to identify the nature of iodine/epoxy-paint interactions and to characterize the gamma radiation damages on the epoxy-paint. AComDim method conduces to the extraction of Common Components to different tables and highlights factors of influence and their interactions. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Interaction of water with epoxy.

    Energy Technology Data Exchange (ETDEWEB)

    Powers, Dana Auburn

    2009-07-01

    The chemistries of reactants, plasticizers, solvents and additives in an epoxy paint are discussed. Polyamide additives may play an important role in the absorption of molecular iodine by epoxy paints. It is recommended that the unsaturation of the polyamide additive in the epoxy cure be determined. Experimental studies of water absorption by epoxy resins are discussed. These studies show that absorption can disrupt hydrogen bonds among segments of the polymers and cause swelling of the polymer. The water absorption increases the diffusion coefficient of water within the polymer. Permanent damage to the polymer can result if water causes hydrolysis of ether linkages. Water desorption studies are recommended to ascertain how water absorption affects epoxy paint.

  5. Dissolution of organic solvents from painted surfaces into water

    International Nuclear Information System (INIS)

    Wren, J.C.; Jobe, D.J.; Sanipelli, G.G.; Ball, J.M.

    2000-01-01

    The presence of volatile iodine in containment buildings is one of the major safety concerns in the potential event of nuclear reactor accidents. Organic impurities in containment water, originating from various painted structural surfaces and organic materials, could have a significant impact on iodine volatility following an accident. To determine the source and magnitude of organic impurities and their effects on time-dependent iodine volatility, the dissolution for organic constituents from paints used in reactor buildings has been studied under postulated accident conditions. The studies of the organic dissolution from carbon steel coupons coated with zinc-primed vinyl, epoxy-primed polyurethane or epoxy paints over the temperature range 25-90 deg C are reported. Relatively large activation energies were measured for the release of the principal organic compounds from painted surfaces, suggesting it is the release of the solvents from the paint matrix rather than their diffusion through the solution that is the rate determining step for the dissolution mechanism. The similarities in the values of activation energies for the dissolution of different organic compounds from the paints suggest the release rate is independent of the nature of the painted surface or the type of organic being released from the surface. These two observations indicate that it may be possible to write a generalized rate expression for the release of organic compounds from painted surfaces in containment following an accident. The possible implications of these results for predicting iodine volatility in containment are also discussed. (author)

  6. Epoxy-paint stripping using TEA CO2 laser: Determination of threshold fluence and the process parameters

    Science.gov (United States)

    Kumar, Manoj; Bhargava, P.; Biswas, A. K.; Sahu, Shasikiran; Mandloi, V.; Ittoop, M. O.; Khattak, B. Q.; Tiwari, M. K.; Kukreja, L. M.

    2013-03-01

    It is shown that the threshold fluence for laser paint stripping can be accurately estimated from the heat of gasification and the absorption coefficient of the epoxy-paint. The threshold fluence determined experimentally by stripping of the epoxy-paint on a substrate using a TEA CO2 laser matches closely with the calculated value. The calculated threshold fluence and the measured absorption coefficient of the paint allowed us to determine the epoxy paint thickness that would be removed per pulse at a given laser fluence even without experimental trials. This was used to predict the optimum scan speed required to strip the epoxy-paint of a given thickness using a high average power TEA CO2 laser. Energy Dispersive X-Ray Fluorescence (EDXRF) studies were also carried out on laser paint-stripped concrete substrate to show high efficacy of this modality.

  7. The main outcomes of the OECD Behaviour of Iodine (BIP) Project

    International Nuclear Information System (INIS)

    Glowa, Glenn A.; Moore, Chris J.; Ball, Joanne M.

    2013-01-01

    Highlights: • Moisture affects the rate of iodine adsorption on paint. • Irradiation of iodine-loaded paint yields methyl iodide. • The BIP project is complimentary to the EPICUR project. • BIP results help with the interpretation of Phébus FP results. - Abstract: An Organisation for Economic Co-operation and Development (OECD) status report on iodine behaviour published in February 2007 concluded that although the understanding of iodine behaviour in containment had advanced considerably over the past several decades, there were still areas where further investigation was warranted. The OECD initiated the Behaviour of Iodine Project (BIP) to investigate two of these areas: • The interaction of iodine with painted surfaces: adsorption of iodine from the gas phase to several containment surfaces was investigated under a variety of conditions, with focus on the role of water on the adsorption of iodine onto epoxy paints. The results show that the relative humidity is very important to the deposition velocity of iodine on paint; higher humidity caused faster deposition. Adsorption parameters are a critical input for containment codes. • The formation of organic iodide from painted surfaces: gas chromatography was used to monitor the evolution of CH 3 I during the irradiation of epoxy coupons pre-loaded with iodine. The results showed that organic iodide formation is greater, and has a different temporal behaviour, when the iodine is absorbed by the paint from the aqueous phase as opposed to from the gas phase. The results also highlighted the importance of destruction of organic iodides by gas phase radiolysis to the concentration of CH 3 I. The BIP organic iodide production experiments were different, but complementary, to the experiments performed in the EPICUR (Experimental Program for Iodine Chemistry Under Radiation) facility. However, both projects share an objective of supporting the explanation of iodine behaviour in the Phébus Fission Product

  8. Leaching of iodine from composites based on epoxy resin and lead iodide

    International Nuclear Information System (INIS)

    Kalinin, N.N.; Elizarova, A.N.

    1988-01-01

    The scope for using solid composites obtained by incorporating dry powdery lead iodide and its aqueous suspension into epoxy resin for prolonged immobilization of iodine-129 under monitorable storage conditions has been assessed by a study of leaching of iodine

  9. Evaluation of Tritium Behavior in the Epoxy Painted Concrete Wall of ITER Hot Cell

    International Nuclear Information System (INIS)

    Nakamura, Hirofumi; Hayashi, Takumi; Kobayashi, Kazuhiro; Nishi, Masataka

    2005-01-01

    Tritium behavior released in the ITER hot cell has been investigated numerically using a combined analytical methods of a tritium transport analysis in the multi-layer wall (concrete and epoxy paint) with the one dimensional diffusion model and a tritium concentration analysis in the hot cell with the complete mixing model by the ventilation. As the results, it is revealed that tritium concentration decay and permeation issues are not serious problem in a viewpoint of safety, since it is expected that tritium concentration in the hot cell decrease rapidly within several days just after removing the tritium release source, and tritium permeation through the epoxy painted concrete wall will be negligible as long as the averaged realistic diffusion coefficient is ensured in the concrete wall. It is also revealed that the epoxy paint on the concrete wall prevents the tritium inventory increase in the concrete wall greatly (two orders of magnitudes), but still, the inventory in the wall is estimated to reach about 0.1 PBq for 20 years operation

  10. Organic chemistry and radiochemistry: study of chemical interactions between iodine and paint of French nuclear reactor in a severe accident situation

    International Nuclear Information System (INIS)

    Aujollet, Y.

    2005-01-01

    In Phebus (French in pile facility; PWR scale 1/5000) experiments, performed by the Institut de Radioprotection et de Surete Nucleaire, few quantities of organic iodides were registered after interaction between iodine and reactor containment paint. This study concerns all mechanisms of chemical reactions between iodine and the polymer of the paint in order to estimate the organic iodides released from the paint. At first, all the paint components had been identified. Several models of chemical sites of the polymer were synthesized and tested with iodine in different conditions of temperature and radiation. These experiments showed interactions between iodine and secondary or tertiary amines by charge transfer. In few cases, the complex of tertiary amines creates oxidation reactions. (author)

  11. Identification of the chemical inventory of different paint types applied in nuclear facilities

    International Nuclear Information System (INIS)

    Sabrina Tietze; Foreman, M.R.St.J.; Ekberg, CH.H.; Chalmers University of Technology, Chemical and Biological Engineering, Goeteborg; Dongen van, B.E.

    2013-01-01

    The floors, concrete walls and many of the metal surfaces in nuclear power plant containments are coated with zinc primers or paint films to preserve the metal surfaces and simplify decontamination in the containment after the occurrence of a severe nuclear incident or accident. A chemical examination of paint films from different nuclear installations out of operation, as well as current operating ones, reveals that different types of paints are used whose composition can vary significantly. Results obtained for one type of paint at a certain nuclear site are in most cases unlikely to be comparable with sites painted with another type of paint. During normal operation and particularly during nuclear accidents, the paints will degrade under the high temperature, steam and irradiation influence. As paint and its degradation products can act as sources and depots for volatile iodine compounds, the type and aging conditions of the paint films will have a significant impact on the source term of the volatile fission product iodine. Thus, great care should be taken when extrapolating any results obtained for the interaction of radioactive iodine with one paint product to a different paint product. The main focus of the study is a comparison of the chemical profile of paint films applied in Swedish nuclear power plants. Teknopox Aqua V A, an epoxy paint recently used at Ringhals 2, and an emulsion paint used in the scrubber buildings of Ringhals 1-4 are compared with a paint film from Barsebaeck nuclear power plant unit 1 that had been aged under real reactor conditions for 20 years. In addition, two paint films, an emulsion and a gloss paint, used in an international nuclear fuel reprocessing facility, are compared with the paints from the Swedish nuclear power plants. (author)

  12. Comparison of Dust Release from Epoxy and Paint Nanocomposites and Conventional Products during Sanding and Sawing

    DEFF Research Database (Denmark)

    Gomez, V.; Levin, Marcus; Saber, A. T.

    2014-01-01

    The release of dust generated during sanding or sawing of nanocomposites was compared with conventional products without nanomaterials. Epoxy-based polymers with and without carbon nanotubes, and paints with different amounts of nano-sized titanium dioxide, were machined in a closed aerosol chamber...

  13. Effect of hydrophobic paints coating for tritium reduction in concrete materials

    International Nuclear Information System (INIS)

    Edao, Y.; Fukada, S.; Nishimura, Y.; Katayama, K.; Takeishi, T.; Hatano, Y.; Taguchi, A.

    2012-01-01

    Highlights: ► Effects of hydrophobic paint coating in tritium transport are investigated. ► Two kinds of paints, acrylic-silicon resin and epoxy resin are used. ► The hydrophobic paints are effective to reduce tritium permeation. ► The effect of tritium reduction of epoxy paint is higher than that of silicon. - Abstract: The effects of hydrophobic paint coating on a concrete material of cement paste on the tritium transport are investigated. The cement paste is coated with two kinds of paints, acrylic-silicon resin paint and epoxy resin paint. We investigated the amount of tritium trapped in the samples exposed to tritiated water vapor by means of sorption and release. It was found that both the hydrophobic paints could reduce effectively tritium permeation during 50 days exposure of tritiated water vapor. The effect of tritium reduction of the epoxy paint was higher than that of silicon while the amount of tritium trapped in the epoxy paint was larger than that of silicon due to difference of the structure. Based on an analysis of a diffusion model, the rate-determining step of tritium migration through cement paste coated with the paints is diffusion through the paints respectively. It was found that tritium was easy to penetrate through silicon because there were many pores or voids in the silicon comparatively. In the case of tritium released from the epoxy paint, it is considered that tritium diffusion in epoxy is slow due to retardation by isotope exchange reaction to water included in epoxy paint.

  14. Thickness dependence of the poling and current-voltage characteristics of paint films made up of lead zirconate titanate ceramic powder and epoxy resin

    Science.gov (United States)

    Egusa, Shigenori; Iwasawa, Naozumi

    1995-11-01

    A specially prepared paint made up of lead zirconate titanate (PZT) ceramic powder and epoxy resin was coated on an aluminum plate and was cured at room temperature, thus forming the paint film of 25-300 μm thickness with a PZT volume fraction of 53%. The paint film was then poled at room temperature, and the poling behavior was determined by measuring the piezoelectric activity as a function of poling field. The poling behavior shows that the piezoelectric activity obtained at a given poling field increases with an increase in the film thickness from 25 to 300 μm. The current-voltage characteristic of the paint film, on the other hand, shows that the increase in the film thickness leads not only to an increase in the magnitude of the current density at a given electric field but also to an increase in the critical electric field at which the transition from the ohmic to space-charge-limited conduction takes place. This fact indicates that the amount of the space charge of electrons injected into the paint film decreases as the film thickness increases. Furthermore, comparison of the current-voltage characteristic of the paint film with that of a pure epoxy film reveals that the space charge is accumulated largely at the interface between the PZT and epoxy phases in the paint film. On the basis of this finding, a model is developed for the poling behavior of the paint film by taking into account a possible effect of the space-charge accumulation and a broad distribution of the electric field in the PZT phase. This model is shown to give an excellent fit to the experimental data of the piezoelectric activity obtained here as a function of poling field and film thickness.

  15. Occupational contact dermatitis caused by 1,3-benzenedimethanamine, N-(2-phenylethyl) derivatives in hardeners for epoxy paints and coatings.

    Science.gov (United States)

    Pesonen, Maria; Kuuliala, Outi; Suomela, Sari; Aalto-Korte, Kristiina

    2016-12-01

    Amines in epoxy hardeners are significant causes of occupational allergic contact dermatitis among workers who use epoxy resin systems. To describe a novel group of contact allergens: N-(2-phenylethyl) derivatives of the reactive amine 1,3-benzenedimethanamine (1,3-BDMA). We describe the clinical examinations and exposure of 6 patients with occupational contact allergy to derivatives of 1,3-BDMA. Of the 6 patients, 4 were spray painters who used epoxy paints, 1 was a floor layer who handled a variety of epoxy coatings, and 1 was a worker in epoxy hardener manufacture. We were able to confirm exposure to epoxy hardeners that contained derivatives of 1,3-BDMA in 5 of the 6 sensitized patients. Despite the close structural resemblance between derivatives of 1,3-BDMA and m-xylylenediamine (MXDA), only 3 patients reacted positively to MXDA. Concomitant contact allergy to diglycidyl ether of bisphenol A resin was seen in 2 of the 6 patients. Because of the lack of a commercially available patch test substance, the diagnosis of contact allergy to derivatives of 1,3-BDMA requires patch testing with either the epoxy hardener product or a hardener ingredient that contains the derivatives of 1,3-BDMA. © 2016 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  16. Direct evidence for coastal iodine particles from Laminaria macroalgae – linkage to emissions of molecular iodine

    Directory of Open Access Journals (Sweden)

    G. McFiggans

    2004-01-01

    Full Text Available Renewal of ultrafine aerosols in the marine boundary layer may lead to repopulation of the marine distribution and ultimately determine the concentration of cloud condensation nuclei (CCN. Thus the formation of nanometre-scale particles can lead to enhanced scattering of incoming radiation and a net cooling of the atmosphere. The recent demonstration of the chamber formation of new particles from the photolytic production of condensable iodine-containing compounds from diiodomethane (CH2I2, (O'Dowd et al., 2002; Kolb, 2002; Jimenez et al., 2003a; Burkholder and Ravishankara, 2003, provides an additional mechanism to the gas-to-particle conversion of sulphuric acid formed in the photo-oxidation of dimethylsulphide for marine aerosol repopulation. CH2I2 is emitted from seaweeds (Carpenter et al., 1999, 2000 and has been suggested as an initiator of particle formation. We demonstrate here for the first time that ultrafine iodine-containing particles are produced by intertidal macroalgae exposed to ambient levels of ozone. The particle composition is very similar both to those formed in the chamber photo-oxidation of diiodomethane and in the oxidation of molecular iodine by ozone. The particles formed in all three systems are similarly aspherical. When small, those formed in the molecular iodine system swell only moderately when exposed to increased humidity environments, and swell progressively less with increasing size; this behaviour occurs whether they are formed in dry or humid environments, in contrast to those in the CH2I2 system. Direct coastal boundary layer observations of molecular iodine, ultrafine particle production and iodocarbons are reported. Using a newly measured molecular iodine photolysis rate, it is shown that, if atomic iodine is involved in the observed particle bursts, it is of the order of at least 1000 times more likely to result from molecular iodine photolysis than diiodomethane photolysis. A hypothesis for molecular

  17. Dissociation of molecular iodine in RF discharge for oxygen-iodine laser

    Czech Academy of Sciences Publication Activity Database

    Jirásek, Vít; Schmiedberger, Josef; Čenský, Miroslav; Kodymová, Jarmila

    2012-01-01

    Roč. 66, č. 4 (2012), 1-6 ISSN 1434-6060 R&D Projects: GA ČR GA202/09/0310 Grant - others:European Office for Aerospace R&D(XE) FA8655-09-1-3092 Institutional research plan: CEZ:AV0Z10100523 Keywords : molecular iodine * RF discharge * dissociation * oxygen-iodine laser * COIL Subject RIV: BH - Optics, Masers, Lasers Impact factor: 1.513, year: 2012

  18. Studies on some Indian paints for radiochemical plants

    International Nuclear Information System (INIS)

    Mahesh Kumar, V.V.; Srinivasan, R.; Natarajan, R.

    1996-01-01

    The choice of paints in areas subjected to contamination and radiation in nuclear installation need special attention. The types of generic coatings are examined with reference to these requirements. Among those examined, certain types of epoxy paints are found to be attractive for these applications. Samples of epoxy paints obtained from some Indian manufacturers are tested for their suitability. Decontaminability and radiation resistance properties are also evaluated with special reference to radiochemical plants. Important specifications for such applications are listed. This report summarizes the results of these studies. (author)

  19. The reaction between iodine and organic coatings under severe PWR accident conditions. An experimental parameter study

    Energy Technology Data Exchange (ETDEWEB)

    Hellmann, S; Funke, F; Greger, G U; Bleier, A; Morell, W [Siemens AG, Power Generation Group, Erlangen (Germany)

    1996-12-01

    An extensive experimental parameter study was performed on the deposition and on the resuspension kinetics in the reaction system iodine/organically coated surfaces. Both reactions in the gas phase and in the liquid phase were investigated and kinetic rate constants suitable for modelling were derived. Previous experimental studies on the reaction of iodine with organic coated surfaces were mostly limited to temperatures below 100{sup o}C. Thus, this parameter study aims at filling a gap and providing kinetic data on heterogeneous reactions with organic surfaces in the accident-relevant temperature range of 100-160{sup o}C. Two types of laboratory experiments carried out at Siemens/KWU using coatings representative for German power plants (epoxy-tape paint), namely gas phase tests and liquid phase tests. (author) 6 figs., 6 tabs., 5 refs.

  20. Absorption of airborne molecular iodine by water sprays

    International Nuclear Information System (INIS)

    Albert, M.F.; Wichner, R.P.; Baumgarten, P.K.

    1986-01-01

    A computer model, I2WASH, which accounts for the effect of hydrolysis reactions between molecular iodine and water, has been developed to predict the rate of removal of gaseous molecular iodine by water sprays. It has been shown that the hydrolysis reactions can affect the concentration driving force of mass transfer for molecular iodine absorption. Thus, factors that affect the hydrolysis kinetics, such as spray solution pH, iodine concentration, and temperature, should be considered in the design of a well-based absorption model. The described model also includes the effects of spray drop-size distribution, convective heat transfer, droplet evaporation or water condensation, decay heating, and ventilation air flow through the containment. The model was originally developed at Oak Ridge National Laboratory (ORNL) in 1985 for the Nuclear Regulatory Commission's Severe Accident Sequence Analysis program and has been improved to assist in a comprehensive probability risk assessment of the Savannah River Plant (SRP). Results obtained using the model are compared with those of the Containment Systems Experiments conducted at Pacific Northwest Laboratories (PNL) in 1970. An improvement over the earlier model is indicated at room temperatures, but accuracy decreases as the temperature rises. The decreased agreement at high temperature is partially due to an incomplete knowledge of the temperature effects on iodine hydrolysis reactions. The results of the I2WASH model for a postulated catastrophic accident at SRP show that ∼85% of the molecular iodine will be captured by the sprays at a buffered pH of 10.0, and ∼52% will be captured at a buffered pH of 7.0. The model is believed to be a significant improvement over (and more realistic than) other models

  1. Comparison of dust release from epoxy and paint nanocomposites and conventional products during sanding and sawing.

    Science.gov (United States)

    Gomez, Virginia; Levin, Marcus; Saber, Anne T; Irusta, Silvia; Dal Maso, Miikka; Hanoi, Roberto; Santamaria, Jesus; Jensen, Keld A; Wallin, Håkan; Koponen, Ismo K

    2014-10-01

    The release of dust generated during sanding or sawing of nanocomposites was compared with conventional products without nanomaterials. Epoxy-based polymers with and without carbon nanotubes, and paints with different amounts of nano-sized titanium dioxide, were machined in a closed aerosol chamber. The temporal evolution of the aerosol concentration and size distribution were measured simultaneously. The morphology of collected dust by scanning electron microscopy was different depending on the type of nanocomposites: particles from carbon nanotubes (CNTs) nanocomposites had protrusions on their surfaces and aggregates and agglomerates are attached to the paint matrix in particles emitted from alkyd paints. We observed no significant differences in the particle size distributions when comparing sanding dust from nanofiller containing products with dust from conventional products. Neither did we observe release of free nanomaterials. Instead, the nanomaterials were enclosed or partly enclosed in the matrix. A source strength term Si (cm(-3) s(-1)) that describes particle emission rates from continuous sources was introduced. Comparison between the Si parameters derived from sanding different materials allows identification of potential effects of addition of engineered nanoparticles to a composite. © The Author 2014. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

  2. Parametric studies of radiolytic oxidation of iodide solutions with and without paint: comparison with code calculations

    Energy Technology Data Exchange (ETDEWEB)

    Poletiko, C; Hueber, C [Inst. de Protection et de Surete Nucleaire, C.E. Cadarache, St. Paul-lez-Durance (France); Fabre, B [CISI, C.E. Cadarache, St. Paul-lez-Durance (France)

    1996-12-01

    In case of severe nuclear accident, radioactive material may be released into the environment. Among the fission products involved, are the very volatile iodine isotopes. However, the chemical forms are not well known due to the presence of different species in the containment with which iodine may rapidly react to form aerosols, molecular iodine, hydroiodic acid and iodo-organics. Tentative explanations of different mechanisms were performed through benchscale tests. A series of tests has been performed at AEA Harwell (GB) to study parameters such as pH, dose rate, concentration, gas flow rate, temperature in relation to molecular iodine production, under dynamic conditions. Another set of tests has been performed in AECL Whiteshell (CA) to study the behaviour of painted coupons, standing in gas phase or liquid phase or both, with iodine compounds under radiation. The purpose of our paper is to synthesize the data and compare the results to the IODE code calculation. Some parameters of the code were studied to fit the experimental result the best. A law, concerning the reverse reaction of iodide radiolytic oxidation, has been proposed versus: pH, concentrations and gas flow-rate. This law does not apply for dose rate variations. For the study of painted coupons, it has been pointed out that molecular iodine tends to be adsorbed or chemically absorbed on the surface in gas phase, but the mechanism should be more sophisticated in the aqueous phase. The iodo-organics present in liquid phase tend to be partly or totally destroyed by oxidation under radiation (depending upon the dose delivered). These points are discussed. (author) 18 figs., 3 tabs., 15 refs.

  3. Thermal conductivity of pillared graphene-epoxy nanocomposites using molecular dynamics

    Science.gov (United States)

    Lakshmanan, A.; Srivastava, S.; Ramazani, A.; Sundararaghavan, V.

    2018-04-01

    Thermal conductivity in a pillared graphene-epoxy nanocomposite (PGEN) is studied using equilibrium molecular dynamics simulations. PGEN is a proposed material for advanced thermal management applications because it combines high in-plane conductivity of graphene with high axial conductivity of a nanotube to significantly enhance the overall conductivity of the epoxy matrix material. Anisotropic conductivity of PGEN has been compared with that of pristine and functionalized carbon nanotube-epoxy nanocomposites, showcasing the advantages of the unique hierarchical structure of PGEN. Compared to pure carbon allotropes, embedding the epoxy matrix also promotes a weaker dependence of conductivity on thermal variations. These features make this an attractive material for thermal management applications.

  4. Allergic contact dermatitis from resin hardeners during the manufacture of thermosetting coating paints.

    Science.gov (United States)

    Foulds, I S; Koh, D

    1992-02-01

    5 production operators from 2 factories manufacturing thermosetting coating paint developed work-related skin disorders within 12 months of the introduction of a new powdered paint product. All 5 workers were found to have allergic contact dermatitis from 2 epoxy resin hardeners, both of which were commercial preparations of triglycidyl isocyanurate (TGIC). 2 of the workers had concomitant sensitization to epoxy resin in the standard series and several of the epoxy resin preparations at the workplace. TGIC has been reported as a contact sensitizer both in persons producing the chemical and among end-users of TGIC-containing products. These 5 reported cases document allergic contact dermatitis from commercial TGIC among exposed workers during an intermediate process of powdered paint manufacture. The possibility of substituting this epoxy resin hardener with less sensitizing alternatives should be explored.

  5. Molecular environment of iodine in naturally iodinated humic substances: Insight from X-ray absorption spectroscopy

    International Nuclear Information System (INIS)

    Schlegel, Michel L.; Mercier-Bion, Florence; Barre, Nicole; Reiller, Pascal; Moulin, Valerie

    2006-01-01

    The molecular environment of iodine in reference inorganic and organic compounds, and in dry humic and fulvic acids (HAs and FAs) extracted from subsurface and deep aquifers was probed by iodine L-3-edge X-ray absorption spectroscopy. The X-ray absorption near-edge structure (XANES) of iodine spectra from HAs and FAs resembled those of organic references and displayed structural features consistent with iodine forming covalent bonds with organic molecules. Simulation of XANES spectra by linear combination of reference spectra suggested the predominance of iodine forming covalent bonds to aromatic rings (aromatic-bound iodine). Comparison of extended X-ray absorption fine structure (EXAFS) spectra of reference and samples further showed that iodine was surrounded by carbon shells at distances comparable to those for references containing aromatic-bound iodine. Quantitative analysis of EXAFS spectra indicated that iodine was bound to about one carbon at a distance d(I-C) of 2.01(4)-2.04(9) angstrom, which was comparable to the distances observed for aromatic-bound iodine in references (1.99(1)-2.07(6) angstrom), and significantly shorter than that observed for aliphatic-bound iodine (2.15(2)-2.16(2) angstrom). These results are in agreement with previous conclusions from X-ray photoelectron spectroscopy and from electro-spray ionization mass spectrometry. These results collectively suggest that the aromatic-bound iodine is stable in the various aquifers of this study. (authors)

  6. Molecular Modeling of Aerospace Polymer Matrices Including Carbon Nanotube-Enhanced Epoxy

    Science.gov (United States)

    Radue, Matthew S.

    Carbon fiber (CF) composites are increasingly replacing metals used in major structural parts of aircraft, spacecraft, and automobiles. The current limitations of carbon fiber composites are addressed through computational material design by modeling the salient aerospace matrix materials. Molecular Dynamics (MD) models of epoxies with and without carbon nanotube (CNT) reinforcement and models of pure bismaleimides (BMIs) were developed to elucidate structure-property relationships for improved selection and tailoring of matrices. The influence of monomer functionality on the mechanical properties of epoxies is studied using the Reax Force Field (ReaxFF). From deformation simulations, the Young's modulus, yield point, and Poisson's ratio are calculated and analyzed. The results demonstrate an increase in stiffness and yield strength with increasing resin functionality. Comparison between the network structures of distinct epoxies is further advanced by the Monomeric Degree Index (MDI). Experimental validation demonstrates the MD results correctly predict the relationship in Young's moduli for all epoxies modeled. Therefore, the ReaxFF is confirmed to be a useful tool for studying the mechanical behavior of epoxies. While epoxies have been well-studied using MD, there has been no concerted effort to model cured BMI polymers due to the complexity of the network-forming reactions. A novel, adaptable crosslinking framework is developed for implementing 5 distinct cure reactions of Matrimid-5292 (a BMI resin) and investigating the network structure using MD simulations. The influence of different cure reactions and extent of curing are analyzed on the several thermo-mechanical properties such as mass density, glass transition temperature, coefficient of thermal expansion, elastic moduli, and thermal conductivity. The developed crosslinked models correctly predict experimentally observed trends for various properties. Finally, the epoxies modeled (di-, tri-, and tetra

  7. Analyzing FTIR spectra using high sensitivity compare function of FTIR software for 2-pack epoxy paints

    Science.gov (United States)

    Saaid, Farish Irfal; Chan, Chin Han; Ong, Max Chong Hup; Winie, Tan; Harun, Mohamad Kamal

    2015-08-01

    The existing problem of oil and gas companies faced for on-site jobs of polymeric coatings on steel pipelines is that the quality of polymeric coatings varies from job to job for the same product brand from the same supplier or paint manufacturer. This can be due to the inherent problem of the reformulation of polymeric coatings or in other words adulterated polymeric coatings are supplied, where the quality of the coatings deviates from the submitted specifications for prequalification and tender purpose. Major oil and gas companies in Malaysia are calling for Coating Fingerprinting Certificate for the supply of polymeric coatings from local paint manufactures as quality assurance requirement of the coatings supplied. This will reduce the possibility of failures of the polymeric coatings, which lead to the corrosion of steel pipelines resulting in leakage of crude oil and gas to the environment. In this case, Fourier-transform infrared (FTIR) is a simple and reliable tool for coating fingerprinting. In this study, we conclude that, revelation of possible components of the 2-pack epoxy paints by carrying out extensive FTIR libraries search on FTIR spectra seems to be extremely challenging. Estimation of correlation of the sample spectrum to that of the reference spectrum using Compare function from one FTIR manufacturer, even the FTIR spectra are collected by different FTIR spectrometers from different FTIR manufacturers, can be made. The results of the correlation are reproducible.

  8. PARIS project: Radiolytic oxidation of molecular iodine in containment during a nuclear reactor severe accident

    Energy Technology Data Exchange (ETDEWEB)

    Bosland, L. [Institut de Radioprotection et de Surete Nucleaire, DPAM, SEMIC, LETR - CEN Cadarache, BP 3, 13115 Saint Paul Lez Durance (France)], E-mail: loic.bosland@irsn.fr; Funke, F. [AREVA NP GmbH, Technical Center, P.O. Box 1109, D-91001 Erlangen (Germany); Girault, N. [Institut de Radioprotection et de Surete Nucleaire, DPAM, SEMIC, LETR - CEN Cadarache, BP 3, 13115 Saint Paul Lez Durance (France); Langrock, G. [AREVA NP GmbH, Technical Center, P.O. Box 1109, D-91001 Erlangen (Germany)

    2008-12-15

    In case of a hypothetical severe accident in a nuclear LWR (light water reactor), the high radiation fields reached in the reactor containment building due to the release of fission products from the reactor core could induce air radiolysis. The air radiolysis products could, in turn, oxidise gaseous molecular iodine into aerosol-borne iodine-oxygen-nitrogen compounds. Thereby, this reaction involves a change of iodine speciation and a decrease of iodine volatility in the reactor containment atmosphere. Kinetic data were produced within the PARIS project on the air radiolysis products formation and destruction, and on their reaction with molecular iodine, with the objective of developing and validating existing kinetic models. The current paper includes the non-iodine tests of the PARIS project whose objective was to determine the rates of formation and destruction of air radiolysis products in the presence of both structural containment surfaces (decontamination coating ('paint') and stainless steel), aerosol particles such as silver rich particles (issued from the control rods) in boundary conditions representative for LWR or PHEBUS facility containments. It is found that the air radiolysis products concentration increases with dose and tend to approach saturation levels at doses higher than about 1 kGy. This behaviour is more evident in oxygen/steam atmospheres, producing ozone, than in air/30% (v/v) steam atmospheres, the latter favouring the model-predicted on-going production of nitrogen dioxide even at very high doses. No significant effect of temperature, dose rate and hydrogen addition (4%, v/v) was observed. Furthermore, the inserted surfaces do not exhibit significant effects on the air radiolysis concentrations. However, these 'non-noticeable influence' could be due to a masking of small effects by the appreciable scattering of the experimental air radiolysis product concentrations. The PARIS results are then analysed using two

  9. PARIS project: Radiolytic oxidation of molecular iodine in containment during a nuclear reactor severe accident

    International Nuclear Information System (INIS)

    Bosland, L.; Funke, F.; Girault, N.; Langrock, G.

    2008-01-01

    In case of a hypothetical severe accident in a nuclear LWR (light water reactor), the high radiation fields reached in the reactor containment building due to the release of fission products from the reactor core could induce air radiolysis. The air radiolysis products could, in turn, oxidise gaseous molecular iodine into aerosol-borne iodine-oxygen-nitrogen compounds. Thereby, this reaction involves a change of iodine speciation and a decrease of iodine volatility in the reactor containment atmosphere. Kinetic data were produced within the PARIS project on the air radiolysis products formation and destruction, and on their reaction with molecular iodine, with the objective of developing and validating existing kinetic models. The current paper includes the non-iodine tests of the PARIS project whose objective was to determine the rates of formation and destruction of air radiolysis products in the presence of both structural containment surfaces (decontamination coating ('paint') and stainless steel), aerosol particles such as silver rich particles (issued from the control rods) in boundary conditions representative for LWR or PHEBUS facility containments. It is found that the air radiolysis products concentration increases with dose and tend to approach saturation levels at doses higher than about 1 kGy. This behaviour is more evident in oxygen/steam atmospheres, producing ozone, than in air/30% (v/v) steam atmospheres, the latter favouring the model-predicted on-going production of nitrogen dioxide even at very high doses. No significant effect of temperature, dose rate and hydrogen addition (4%, v/v) was observed. Furthermore, the inserted surfaces do not exhibit significant effects on the air radiolysis concentrations. However, these 'non-noticeable influence' could be due to a masking of small effects by the appreciable scattering of the experimental air radiolysis product concentrations. The PARIS results are then analysed using two different kinetic models

  10. Effects of Molecular Iodine and 4-tert-Butylcatechol Radical Inhibitor on the Radical Polymerization of Styrene

    Directory of Open Access Journals (Sweden)

    Mojtaba Bozorg

    2017-05-01

    Full Text Available The presence of molecular iodine was studied in relation the molecular weight and molecular weight distribution of polystyrene, produced by radical poly merization. Radical polymerization of styrene initiated by 2,2׳-azobisisobutyronitrile (AIBN was performed at 70°C in the presence of molecular iodine. The synthesized polymers were characterized by gel permeation chromatography (GPC and proton- nuclear magnetic resonance (1H NMR techniques. The results of these reactions including conversion data, number-average molecular weight and molecular weight distribution were compared with those obtained for styrene radical polymerization initiated by AIBN at the same temperature in the absence of molecular iodine. It was found that the presence of iodine had a profound effect on the molecular weight and its distribution in the produced polystyrene. This was attributed to the ability of iodine to control the polymerization of styrene initiated by AIBN via reverse iodine transfer polymerization (RITP mechanism. The polymer produced by this method had a molecular weight of 10600 g/mol with a molecular weight polydispersity index of 1.3. Due to the importance of induction period in reverse iodine transfer radical polymerization, increasing the temperature to 120°C during the induction period resulted in shorter induction periods and the produced species led to better control of the molecular weight. Also, due to the role of iodine molecules as a radical inhibitor, the presence of a secondary radical inhibitor, i.e. 4-tert-butylcatechol, along with the iodine was investigated in radical polymerization of polystyrene initiated by AIBN. It was observed that the secondary radical inhibitor prevented the consumption of the iodine molecules by the radicals produced from decomposition of the AIBN initiator; therefore, alkyl halides were not produced during the induction period.

  11. The sorption of iodine by an inorganic zinc primer

    Energy Technology Data Exchange (ETDEWEB)

    Evans, G J; Bekeris, P A [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

    1996-12-01

    The purpose of this work was to identify and evaluate significant parameters in the sorption of I{sub 2}(g) onto Carbo Zinc 11 inorganic primer, a paint used in the containment structure of some CANDU reactors. Air containing known amounts of {sup 131}I{sub 2}(g) was passed through 0.64 cm diameter glass tubing coated on the inner surface with paint. The accumulation of iodine on the surface was continuously monitored using two scintillation detectors. The test parameters covered were relative humidity, flow rate, I{sub 2} concentration and paint temperature. Adsorption was rapid at 23{sup o}C and predominantly gas phase mass transfer limited: the deposition velocity of 0.7{+-}0.4 cm/s was similar to the gas phase mass transfer coefficient of 1.2 cm/s estimated for the system. The deposition velocity observed at a higher paint surface temperature was an order of magnitude smaller. A similar deposition velocity was observed at 23{sup o}C for adsorption of I{sub 2}(g) from essentially dry air suggesting that the low deposition velocity observed for high surface temperature was limited by the amount of water on the paint surface. The rate of adsorption on the paint was directly proportional to the I{sub 2}(g) concentration over the range in concentration studied. The majority of the iodine retained by the paint could not be removed by washing with methanol or chloroform, but it was removed by water indicating that it was in an ionic form. Analysis of the speciation of the iodine in the wash water indicated that only a third of it was in the form of I{sup -}; the form of the remaining iodine could not be resolved. Desorption from the paint was negligible at room temperature but was detectable at higher temperatures. These low desorption rates and the ionic nature of the surface iodine indicated that adsorption occurred predominantly through a chemisorption process. A number of possible mechanisms were proposed. (author) 5 figs., 2 tabs., 6 refs.

  12. Active molecular iodine photochemistry in the Arctic.

    Science.gov (United States)

    Raso, Angela R W; Custard, Kyle D; May, Nathaniel W; Tanner, David; Newburn, Matt K; Walker, Lawrence; Moore, Ronald J; Huey, L G; Alexander, Liz; Shepson, Paul B; Pratt, Kerri A

    2017-09-19

    During springtime, the Arctic atmospheric boundary layer undergoes frequent rapid depletions in ozone and gaseous elemental mercury due to reactions with halogen atoms, influencing atmospheric composition and pollutant fate. Although bromine chemistry has been shown to initiate ozone depletion events, and it has long been hypothesized that iodine chemistry may contribute, no previous measurements of molecular iodine (I 2 ) have been reported in the Arctic. Iodine chemistry also contributes to atmospheric new particle formation and therefore cloud properties and radiative forcing. Here we present Arctic atmospheric I 2 and snowpack iodide (I - ) measurements, which were conducted near Utqiaġvik, AK, in February 2014. Using chemical ionization mass spectrometry, I 2 was observed in the atmosphere at mole ratios of 0.3-1.0 ppt, and in the snowpack interstitial air at mole ratios up to 22 ppt under natural sunlit conditions and up to 35 ppt when the snowpack surface was artificially irradiated, suggesting a photochemical production mechanism. Further, snow meltwater I - measurements showed enrichments of up to ∼1,900 times above the seawater ratio of I - /Na + , consistent with iodine activation and recycling. Modeling shows that observed I 2 levels are able to significantly increase ozone depletion rates, while also producing iodine monoxide (IO) at levels recently observed in the Arctic. These results emphasize the significance of iodine chemistry and the role of snowpack photochemistry in Arctic atmospheric composition, and imply that I 2 is likely a dominant source of iodine atoms in the Arctic.

  13. Active molecular iodine photochemistry in the Arctic

    Energy Technology Data Exchange (ETDEWEB)

    Raso, Angela R.; Custard, Kyle D.; May, Nathaniel W.; Tanner, David; Newburn, Matthew K.; Walker, Lawrence R.; Moore, Ronald J.; Huey, L. G.; Alexander, Lizabeth; Shepson, Paul B.; Pratt, Kerri A.

    2017-09-05

    During springtime, the Arctic atmospheric boundary layer undergoes frequent rapid depletions in ozone and gaseous elemental mercury due to reactions with halogen atoms, influencing atmospheric composition and pollutant fate. Although bromine chemistry has been shown to initiate ozone depletion events, and it has long been hypothesized that iodine chemistry may contribute, no previous measurements of molecular iodine (I2) have been reported in the Arctic. Iodine chemistry also contributes to atmospheric new particle formation and therefore cloud properties and radiative forcing. Here we present Arctic atmospheric I2 and snowpack iodide (I-) measurements, which were conducted near Utqiagvik, AK, in February 2014. Using chemical ionization mass spectrometry, I2 was observed in the atmosphere at mole ratios of 0.3–1.0 ppt, and in the snowpack interstitial air at mole ratios up to 22 ppt under natural sunlit conditions and up to 35 ppt when the snowpack surface was artificially irradiated, suggesting a photochemical production mechanism. Further, snow meltwater I-measurements showed enrichments of up to ~1,900 times above the seawater ratio of I-/Na+, consistent with iodine activation and recycling. Modeling shows that observed I2 levels are able to significantly increase ozone depletion rates, while also producing iodine monoxide (IO) at levels recently observed in the Arctic. These results emphasize the significance of iodine chemistry and the role of snowpack photochemistry in Arctic atmospheric composition, and imply that I2 is likely a dominant source of iodine atoms in the Arctic.

  14. Temperature dependence of creep compliance of highly cross-linked epoxy: A molecular simulation study

    International Nuclear Information System (INIS)

    Khabaz, Fardin; Khare, Ketan S.; Khare, Rajesh

    2014-01-01

    We have used molecular dynamics (MD) simulations to study the effect of temperature on the creep compliance of neat cross-linked epoxy. Experimental studies of mechanical behavior of cross-linked epoxy in literature commonly report creep compliance values, whereas molecular simulations of these systems have primarily focused on the Young’s modulus. In this work, in order to obtain a more direct comparison between experiments and simulations, atomistically detailed models of the cross-linked epoxy are used to study their creep compliance as a function of temperature using MD simulations. The creep tests are performed by applying a constant tensile stress and monitoring the resulting strain in the system. Our results show that simulated values of creep compliance increase with an increase in both time and temperature. We believe that such calculations of the creep compliance, along with the use of time temperature superposition, hold great promise in connecting the molecular insight obtained from molecular simulation at small length- and time-scales with the experimental behavior of such materials. To the best of our knowledge, this work is the first reported effort that investigates the creep compliance behavior of cross-linked epoxy using MD simulations

  15. Formation and behaviour of organic iodine

    International Nuclear Information System (INIS)

    Zilliacus, R.; Koukkar, P.; Karjunen, T.; Sjoevall, H.

    2002-01-01

    The report presents experimental studies on the formation of organic iodine in severe reactor accidents. The analyses were performed to evaluate the amount of alkaline chemical needed for effective pH control of containment water during the accidents. The formation of organic iodine in solutions used in the filtered venting system and the absorption of iodine compounds in the solutions were studied. Experiments for the formation of organic iodine on painted surfaces were also performed. (au)

  16. Adsorption and revaporisation studies of thin iodine oxide and CsI aerosol deposits from containment surface materials in LWRs

    Energy Technology Data Exchange (ETDEWEB)

    Tietze, S.; Foreman, M.; Ekberg, C. [Chalmers Univ. of Technology, Goeteborg (Sweden); Kaerkelae, T.; Auvinen, A.; Tapper, U.; Jokiniemi, J. [VTT Technical Research Centre of Finland, Espoo (Finland)

    2013-07-15

    During a severe nuclear accident released fission and radiolysis products can react with each other to form new species which might contribute to the volatile source term. Iodine will be released from UO2 fuel mainly in form as CsI aerosol particles and elemental iodine. Elemental iodine can react in gaseous phase with ozone to form solid iodine oxide aerosol particles (IOx). Within the AIAS-2 (Adsorption of Iodine Aerosols on Surfaces) project the interactions of IOx and CsI aerosols with common containment surface materials was investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS. Non-radioactive and {sup 131}I labelled aerosols were produced from a KI solution and ozone with a new facility designed and built at VTT Technical Research Centre of Finland. CsI aerosols were produced from a CsI solution with the same facility. A monolayer of the aerosols was deposited on the surfaces. The deposits were analysed with microscopic and spectroscopic measurement techniques to identify the chemical form of the deposits on the surfaces to identify if a chemical conversion on the different surface materials had occured. The revaporisation behaviour of the deposited aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 with a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The decomposition effect of the radiolysis product carbon monoxide was tested on IOx aerosols deposited on a glass fibre filter. Iodine oxide particles were produced at 50 deg. C, 100 deg. C and 120 deg. C and deposited on filter samples in order to study the chemical

  17. Adsorption and revaporisation studies of thin iodine oxide and CsI aerosol deposits from containment surface materials in LWRs

    International Nuclear Information System (INIS)

    Tietze, S.; Foreman, M.; Ekberg, C.; Kaerkelae, T.; Auvinen, A.; Tapper, U.; Jokiniemi, J.

    2013-07-01

    During a severe nuclear accident released fission and radiolysis products can react with each other to form new species which might contribute to the volatile source term. Iodine will be released from UO2 fuel mainly in form as CsI aerosol particles and elemental iodine. Elemental iodine can react in gaseous phase with ozone to form solid iodine oxide aerosol particles (IOx). Within the AIAS-2 (Adsorption of Iodine Aerosols on Surfaces) project the interactions of IOx and CsI aerosols with common containment surface materials was investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS. Non-radioactive and 131 I labelled aerosols were produced from a KI solution and ozone with a new facility designed and built at VTT Technical Research Centre of Finland. CsI aerosols were produced from a CsI solution with the same facility. A monolayer of the aerosols was deposited on the surfaces. The deposits were analysed with microscopic and spectroscopic measurement techniques to identify the chemical form of the deposits on the surfaces to identify if a chemical conversion on the different surface materials had occured. The revaporisation behaviour of the deposited aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 with a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The decomposition effect of the radiolysis product carbon monoxide was tested on IOx aerosols deposited on a glass fibre filter. Iodine oxide particles were produced at 50 deg. C, 100 deg. C and 120 deg. C and deposited on filter samples in order to study the chemical speciation of

  18. Molecular Iodine Fluorescence Using a Green Helium-Neon Laser

    Science.gov (United States)

    Williamson, J. Charles

    2011-01-01

    Excitation of molecular iodine vapor with a green (543.4 nm) helium-neon laser produces a fluorescence spectrum that is well suited for the upper-level undergraduate physical chemistry laboratory. Application of standard evaluation techniques to the spectrum yields ground electronic-state molecular parameters in good agreement with literature…

  19. Molecular Mechanics of the Moisture Effect on Epoxy/Carbon Nanotube Nanocomposites

    Directory of Open Access Journals (Sweden)

    Lik-ho Tam

    2017-10-01

    Full Text Available The strong structural integrity of polymer nanocomposite is influenced in the moist environment; but the fundamental mechanism is unclear, including the basis for the interactions between the absorbed water molecules and the structure, which prevents us from predicting the durability of its applications across multiple scales. In this research, a molecular dynamics model of the epoxy/single-walled carbon nanotube (SWCNT nanocomposite is constructed to explore the mechanism of the moisture effect, and an analysis of the molecular interactions is provided by focusing on the hydrogen bond (H-bond network inside the nanocomposite structure. The simulations show that at low moisture concentration, the water molecules affect the molecular interactions by favorably forming the water-nanocomposite H-bonds and the small cluster, while at high concentration the water molecules predominantly form the water-water H-bonds and the large cluster. The water molecules in the epoxy matrix and the epoxy-SWCNT interface disrupt the molecular interactions and deteriorate the mechanical properties. Through identifying the link between the water molecules and the nanocomposite structure and properties, it is shown that the free volume in the nanocomposite is crucial for its structural integrity, which facilitates the moisture accumulation and the distinct material deteriorations. This study provides insights into the moisture-affected structure and properties of the nanocomposite from the nanoscale perspective, which contributes to the understanding of the nanocomposite long-term performance under the moisture effect.

  20. Molecular Mechanics of the Moisture Effect on Epoxy/Carbon Nanotube Nanocomposites.

    Science.gov (United States)

    Tam, Lik-Ho; Wu, Chao

    2017-10-13

    The strong structural integrity of polymer nanocomposite is influenced in the moist environment; but the fundamental mechanism is unclear, including the basis for the interactions between the absorbed water molecules and the structure, which prevents us from predicting the durability of its applications across multiple scales. In this research, a molecular dynamics model of the epoxy/single-walled carbon nanotube (SWCNT) nanocomposite is constructed to explore the mechanism of the moisture effect, and an analysis of the molecular interactions is provided by focusing on the hydrogen bond (H-bond) network inside the nanocomposite structure. The simulations show that at low moisture concentration, the water molecules affect the molecular interactions by favorably forming the water-nanocomposite H-bonds and the small cluster, while at high concentration the water molecules predominantly form the water-water H-bonds and the large cluster. The water molecules in the epoxy matrix and the epoxy-SWCNT interface disrupt the molecular interactions and deteriorate the mechanical properties. Through identifying the link between the water molecules and the nanocomposite structure and properties, it is shown that the free volume in the nanocomposite is crucial for its structural integrity, which facilitates the moisture accumulation and the distinct material deteriorations. This study provides insights into the moisture-affected structure and properties of the nanocomposite from the nanoscale perspective, which contributes to the understanding of the nanocomposite long-term performance under the moisture effect.

  1. The interaction of iodine with organic material in containment

    Energy Technology Data Exchange (ETDEWEB)

    Wren, J C; Ball, J M; Glown, G A; Portmann, R; Sanipelli, G G [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Labs.

    1996-12-01

    Organic impurities in containment water, originating from various painted structural surfaces and organic containment materials, could have a significant impact on iodine volatility following an accident. A research program has been designed to determine the impact of organic impurities on iodine volatility under accident conditions. The program consists of experimental, literature and modelling studies on the radiolysis or organic compounds in the aqueous phase, thermal and radiolytic formation and decomposition of organic iodides, dissolution of organic solvents from various painted surfaces into the aqueous phase, and iodine deposition on painted surfaces. The experimental studies consist of bench-scale `separate effects` tests as well as intermediate-scale `integrated effects` in the Radioiodine Test facility. The studies have shown that organic impurities will be found in containment water, arising from the dissolution of organic compounds from various surface paints and that these compounds can potentially have a significant impact on iodine volatility following an accident. The main impact of surface paints will occur through aqueous-phase reactions of the organic compounds that they release to the aqueous phase. Under the radiation conditions expected during an accident, these compounds will react to reduce the pH and dissolved oxygen concentration, consequently increasing the formation of I{sub 2} from I{sup -} that is present in the sump. It appears that the rates of these processes may be controlled by the dissolution kinetics of the organic compounds from the surface coatings. Moreover, the organic compounds may also react thermally and radiolytically with I{sub 2} to form organic iodides in the aqueous phase. Our studies have shown that the formation of organic iodides from soluble organics such as ketones, alcohols and phenols may have more impact on the total iodine volatility than the formation of CH{sub 3}I. (author) 13 figs., 2 tabs., 19 refs.

  2. The interaction of iodine with organic material in containment

    International Nuclear Information System (INIS)

    Wren, J.C.; Ball, J.M.; Glown, G.A.; Portmann, R.; Sanipelli, G.G.

    1996-01-01

    Organic impurities in containment water, originating from various painted structural surfaces and organic containment materials, could have a significant impact on iodine volatility following an accident. A research program at the Whiteshell Laboratories of AECL has been designed to determine the impact of organic impurities on iodine volatility under accident conditions. The program consists of experimental, literature and modelling studies on the radiolysis or organic compounds in the aqueous phase, thermal and radiolytic formation and decomposition of organic iodides, dissolution of organic solvents from various painted surfaces into the aqueous phase, and iodine deposition on painted surfaces. The experimental studies consist of bench-scale 'separate effects' tests as well as intermediate-scale 'integrated effects' in the Radioiodine Test facility. The studies have shown that organic impurities will be found in containment water, arising from the dissolution of organic compounds from various surface paints and that these compounds can potentially have a significant impact on iodine volatility following an accident. The main impact of surface paints will occur through aqueous-phase reactions of the organic compounds that they release to the aqueous phase. Under the radiation conditions expected during an accident, these compounds will react to reduce the pH and dissolved oxygen concentration, consequently increasing the formation of I 2 from I - that is present in the sump. It appears that the rates of these processes may be controlled by the dissolution kinetics of the organic compounds from the surface coatings. Moreover, the organic compounds may also react thermally and radiolytically with I 2 to form organic iodides in the aqueous phase. Our studies have shown that the formation of organic iodides from soluble organics such as ketones, alcohols and phenols may have more impact on the total iodine volatility than the formation of CH 3 I. (author) 13 figs., 2

  3. Contribution to the study of gaseous molecular iodine washout by natural rains

    International Nuclear Information System (INIS)

    Fournier-Bidoz, V.

    1991-01-01

    This study is part of researches about nuclear accident prediction consequences on the environment. It concerns transfering of molecular gaseous iodine into liquids and especially precipitation scavenging below the cloud (washout). Bibliographic data directly concerned with this study (iodine's aqueous chemistry, aqueous to gaseous phases transfer) and also with its global frame-work (atmospheric release from a nuclear reactor in accidental situation and the behaviour of atmospheric iodine) are presented. Several experimental approaches have been performed in laboratory and on field. An aqueous to gaseous phase transfer simulator allowed us to isolate parameters involved in absorption and desorption of the halogen. Field experiments permit to quantify dry deposition on different solutions and to get a better insight of the phenomenon. Extrapolation of the whole results to precipitation scavenging of gaseous iodine I 2 by natural rains suggests that the process is an irreversible one. Washout rate values acquired during rainy experiments with molecular iodine emission or in a laboratory rainfall simulator agree with literatures data relative to irreversibility. However and even if reversibility was efficient it was not possible to clearly exhibit it according to experimental conditions. Moreover, the analytical iodine method which leads to a good experimental study has been presented

  4. Piezoelectric paints as one approach to smart structural materials with health-monitoring capabilities

    Science.gov (United States)

    Egusa, Shigenori; Iwasawa, Naozumi

    1998-08-01

    Piezoelectric paints have a potential to change a conventional structural material into an intelligent material system with health-monitoring capabilities such as vibration sensing and damage detection. Such paints were prepared using lead zirconate titanate (PZT) ceramic powder as a pigment and epoxy resin as a binder. The obtained paints were coated on aluminum test specimens, and were cured at room temperature or at 150 0964-1726/7/4/002/img5, thus forming the paint films having different thicknesses of 25-300 0964-1726/7/4/002/img6. These films were then poled at room temperature, and were evaluated with regard to the sensitivities as vibration and acoustic emission sensors in the frequency ranges of 0-250 Hz and 0-1.0 MHz, respectively. This paper mainly describes the effects of the film thickness and the cure temperature on the poling behavior of the PZT/epoxy paint film. This paper describes also the application of the paint film as a vibration modal sensor integrated into a structural material.

  5. The retention of iodine by iodine filters in nuclear power plants in the case of fire

    International Nuclear Information System (INIS)

    Giraud, V.

    1985-01-01

    Due to the liberation of considerable amounts of gaseous combustion products, fires in nuclear power plants may lead to a deterioration in the retention of radioiodine by iodine filters. The combustion products of the burnable materials, i.e., insulations, lubricants and paints, vary considerably with the development of the fire. Combustion product analyses of these materials have been performed only to a limited extent. The reaction of iodine with combustion products as well as the retention of the resulting iodine reaction products by sorbents have not yet been investigated. The reduction in the removal efficiencies of iodine sorbents due to the presence of combustion products is unknown. (orig.) [de

  6. Electrochemical assessment of magnetite anti corrosive paints

    International Nuclear Information System (INIS)

    Escobar, D. M.; Arroyave, C.; Jaramillo, F.; Mattos, O. R.; Margarit, I. c.; Calderon, J.

    2003-01-01

    With the purpose of deepening in the understanding of the mechanisms of protection of anticorrosive pigments based on iron oxides, this work has been carried out on the production of pure magnetite, and copper and chromium doped magnetite, which were evaluated by different characterization techniques. The paints were prepared with a solvent less epoxy resin maintaining the Pigment volume Content near the Practical Critical value (CPVC), established for each pigment. The paints were applied on polished steel and monitored with electrochemical techniques at total immersion conditions. Permeability and impedance measurements of free films were also done. Impedance data were simulated with the Boukamp software. Results show that the paints pigmented with doped magnetite present better behaviour than a paint prepared with commercial hematite. (Author) 8 refs

  7. Study of decontamination and radiation resistance properties of Indian paints

    International Nuclear Information System (INIS)

    Shah, S.M.; Gopinathan, E.; Bhagwath, A.M.

    1976-01-01

    A brief introduction to the study of contamination and radiation resistance properties of Indian paints used as coating for structural materials in the nuclear industry is given. The general composition of paints such as epoxy, vinyl, alkyd, phenolic, chlesimated rubber, etc. is given. Method of sample preparation, processing and actual evaluation of decontaminability are described. The results have been discussed in terms of decontamination factors. Some recommendations based on the performance of the paints studied are also included. (K.B.)

  8. Smart paint sensor for monitoring structural vibrations

    International Nuclear Information System (INIS)

    Al-Saffar, Y; Baz, A; Aldraihem, O

    2012-01-01

    A class of smart paint sensors is proposed for monitoring the structural vibration of beams. The sensor is manufactured from an epoxy resin which is mixed with carbon black nano-particles to make it electrically conducting and sensitive to mechanical vibrations. A comprehensive theoretical and experimental investigation is presented to understand the underlying phenomena governing the operation of this class of paint sensors and evaluate its performance characteristics. A theoretical model is presented to model the electromechanical behavior of the sensor system using molecular theory. The model is integrated with an amplifier circuit in order to predict the current and voltage developed by the paint sensor when subjected to loading. Furthermore, the sensor/amplifier circuit models are coupled with a finite element model of a base beam to which the sensor is bonded. The resulting multi-field model is utilized to predict the behavior of both the sensor and the beam when subjected to a wide variety of vibration excitations. The predictions of the multi-field finite element model are validated experimentally and the behavior of the sensor is evaluated both in the time and the frequency domains. The performance of the sensor is compared with the performance of conventional strain gages to emphasize its potential and merits. The presented techniques are currently being extended to sensors that can monitor the vibration and structural power flow of two-dimensional structures. (paper)

  9. A molecular dynamics study on the interaction between epoxy and functionalized graphene sheets

    DEFF Research Database (Denmark)

    Melro, Liliana Sofia S. F. P.; Pyrz, Ryszard; Jensen, Lars Rosgaard

    2016-01-01

    The interaction between graphene and epoxy resin was studied using molecular dynamics simulations. The interfacial shear strength and pull out force were calculated for functionalised graphene layers (carboxyl, carbonyl, and hydroxyl) and epoxy composites interfaces. The influence of functional...... groups, as well as their distribution and coverage density on the graphene sheets were also analysed through the determination of the Young's modulus. Functionalisation proved to be detrimental to the mechanical properties, nonetheless according to interfacial studies the interaction between graphene...

  10. Nanoclays for polymer nanocomposites, paints, inks, greases and ...

    Indian Academy of Sciences (India)

    Unknown

    An overview of nanoclays or organically modified layered silicates ... silicates; nanocomposites; rheological modifier; drug delivery; waste water. 1. ... enhance the rheological properties of the paint system. .... tems (thermoset and thermoplastic) including epoxy .... involves adding organoclay as a dry powder prior to, or.

  11. The retention of iodine by iodine filters in nuclear power plants in the case of fire (a literature review)

    International Nuclear Information System (INIS)

    Giraud, V.

    1985-03-01

    Due to the liberation of considerable amounts of gaseous combustion products, fires in nuclear power plants may lead to a deterioration in the retention of radioiodine by iodine filters. The combustion products of the burnable materials, i.e., insulations, lubricants and paints, vary considerably with the development of the fire. Combustion product analyses of these materials have been performed only to a limited extent. The reaction of iodine with combustion products as well as the retention of the resulting iodine reaction products by sorbents have not yet been investigated. The reduction in the removal efficiencies of iodine sorbents due to the presence of combustion products is unknown. (orig.) [de

  12. Ultraviolet-radiation-curable paints

    Energy Technology Data Exchange (ETDEWEB)

    Grosset, A M; Su, W F.A.; Vanderglas, E

    1981-09-30

    In product finishing lines, ultraviolet radiation curing of paints on prefabricated structures could be more energy efficient than curing by natural gas fired ovens, and could eliminate solvent emission. Diffuse ultraviolet light can cure paints on three dimensional metal parts. In the uv curing process, the spectral output of radiation sources must complement the absorption spectra of pigments and photoactive agents. Photosensitive compounds, such as thioxanthones, can photoinitiate unsaturated resins, such as acrylated polyurethanes, by a free radical mechanism. Newly developed cationic photoinitiators, such as sulfonium or iodonium salts (the so-called onium salts) of complex metal halide anions, can be used in polymerization of epoxy paints by ultraviolet light radiation. One-coat enamels, topcoats, and primers have been developed which can be photoinitiated to produce hard, adherent films. This process has been tested in a laboratory scale unit by spray coating these materials on three-dimensional objects and passing them through a tunnel containing uv lamps.

  13. Methodology study for fixation of radioactive iodine in polymeric substrate for brachytherapy sources

    International Nuclear Information System (INIS)

    Rodrigues, Bruna T.; Rostelato, Maria Elisa C.M.; Souza, Carla D.; Tiezzi, Rodrigo; Souza, Daiane B. de; Benega, Marcos A.G.; Souza, Anderson S. de; Peleias Junior, Fernando S.; Zeituni, Calos A.; Fernandes, Vagner; Melo, Emerson Ronaldo de; Camargo, Anderson Rogerio de

    2015-01-01

    Cancer is now the second leading cause of death by disease in several countries, including Brazil. Prostate cancer is the most common among men. Brachytherapy is a modality of radiotherapy in which radioactive seeds are placed inside or in contact with the organ to be treated. The most widely used radioisotope in prostate brachytherapy is Iodine-125 which is presented fixated on a silver substrate that is subsequently placed inside a titanium capsule. A large dose of radiation is released only in the targeted tumor protecting healthy surrounding tissues. The technique requires the application of 80 - 120 seeds per patient. The implants of seeds have low impact and non-surgical procedures. Most patients can return to normal life within three days with little or no pain. This work proposes an alternative to the seeds that have already been developed, in order to reduce the cost by obtaining a better efficiency on fixing the radioactive iodine onto the epoxy resin. Methods have been developed to perform the fixation of Iodine-125 onto polymeric substrates. The parameters analyzed were the immersion time, type of static or dynamic reaction, concentration of the adsorption solution, the specific activity of the radioactive source, the need for carrier and chemical form of the radioactive Iodine. These experiments defined the most effective method to fixate the Iodine onto the polymeric material (epoxy resin), the Iodine activity in the polymeric substrate, the activity of the distribution of variation in a plot of polymeric cores and the efficiency of the epoxy resin to seal the seed. (author)

  14. Assessment of integrity of containment coating (Epoxy) using beta radiometry and NDT techniques

    International Nuclear Information System (INIS)

    Pujala, Usha; Sujatha, P.N.; Kumar, Amit; Menaka, M.; Subramanian, V.; Sriniyas, C.V.; Baskaran, R.; Venkataraman, B.; Preetha, R.; Kumar, J. Ashok

    2018-01-01

    The inner sides of walls of reactor containments and other fuel handling areas are coated with paint made of epoxy resins mainly for ease of decontamination and protecting rebar from corrosion environment. In addition, this gives the advantage in terms of ensuring additional leak tightness of reactor containment building (RCB) during the hypothetical Core Disruptive Accident (CDA) of Sodium Cooled Fast Reactors (SFR). During CDA, RCB will be bottled-up with sodium aerosols along with fuel and fission product aerosols. Sodium aerosols undergo chemical changes with progress of time to form hydroxide, carbonate and bicarbonate species upon reaction with atmospheric constituents. Of which, hydroxide aerosols are highly corrosive due to alkaline nature and it can cause damages to the epoxy coating. In this context, experiments have been conducted at ATF to assess the integrity of epoxy coating under the alkaline atmospheric conditions. Plywood, ordinary concrete and zinc plates are coated with epoxy paint and integrity of the coating is checked by exposing to sodium aerosols using beta radiometry technique (BRT), NDT techniques and gravimetric analysis. The results are presented in this paper

  15. Adsorption modes of molecular iodine on defected boron nitrides: A DFT study

    Science.gov (United States)

    Arabieh, Masoud; Azar, Yavar Taghipour

    2018-03-01

    The interaction of molecular iodine with pristine and monovacant boron-nitride quantum dots (QDs) have been investigated using density functional theory. It was found that removing one B or N single atom significantly decreased the calculated Eg values at various exchange functional. In B-defected BN system, the localized spin densities canceled each other and overall polarization of system was found to be equal to unity. For N-defected system there was smaller spin densities localized on each closest B atoms. Both B- and N-vacancies caused appearance of new states in gap region. Our calculation revealed that spin density and polarization of defected system are localized on vacancy region and other atoms did not take part in this polarization. The results of electron localization function for N-DBN showed there was high density region at the position of removed nitrogen atom. The calculated adsorption energies implied that there was no significant chemical interaction between iodine molecule and pristine BN sheet. We suggested that when a deficiency was imposed to the BN sheet, the reactivity of the modified system toward iodine molecule significantly could increase. We found strong interaction between iodine and nitrogen atoms of B-DBN system. In the case of I2/N-DBN system the neighbor atoms had no contribution in spin polarization of the system and it seemed that all spin density of system transferred to the iodine molecule after adsorption. Strong correlation between molecular iodine orientation and BN-QDs via their interactions type has been clarified in this work. These findings may provide a deeper insight into halogen molecules interactions with low dimensional defected boron nitrides.

  16. A Molecular Iodine Spectral Data Set for Rovibronic Analysis

    Science.gov (United States)

    Williamson, J. Charles; Kuntzleman, Thomas S.; Kafader, Rachael A.

    2013-01-01

    A data set of 7,381 molecular iodine vapor rovibronic transitions between the X and B electronic states has been prepared for an advanced undergraduate spectroscopic analysis project. Students apply standard theoretical techniques to these data and determine the values of three X-state constants (image omitted) and four B-state constants (image…

  17. A facile dip-coating process for preparing highly durable superhydrophobic surface with multi-scale structures on paint films.

    Science.gov (United States)

    Cui, Zhe; Yin, Long; Wang, Qingjun; Ding, Jianfu; Chen, Qingmin

    2009-09-15

    Superhydrophobic surfaces with multi-scale nano/microstructures have been prepared on epoxy paint surfaces using a feasible dip-coating process. The microstructures with 5-10 microm protuberances were first prepared on epoxy paint surface by sandblast. Then the nanostructures were introduced on the microstructure surface by anchoring 50-100 nm SiO(2) particles (nano-SiO(2)) onto the sandblasted paint surface, which was completed by dip-coating with a nano-SiO(2)/epoxy adhesive solution (M1). At last the surface was further modified for enhancing hydrophobicity by another dip-coating with a solution of a low surface energy polymer, aminopropyl terminated polydimethylsiloxane (ATPS) modified epoxy adhesive (M2). The water contact angle of the as-prepared samples reached as high as 167.8 degrees and the sliding angle was 7 degrees. The prepared superhydrophobic surface exhibited excellent durability to the high speed scouring test and high stability in neutral and basic aqueous solutions and some common organic solvents. In addition, this method can be adopted to fabricate large scale samples with a good homogeneity of the whole surface at very low cost.

  18. Radiolytical oxidation of gaseous iodine by beta radiation

    International Nuclear Information System (INIS)

    Kaerkelae, Teemu; Auvinen, Ari; Kekki, Tommi; Kotiluoto, Petri; Lyyraenen, Jussi; Jokiniemi, Jorma

    2015-01-01

    Iodine is one of the most radiotoxic fission product released from fuel during a severe nuclear power plant accident. Within the containment building, iodine compounds can react e.g. on the painted surfaces and form gaseous organic iodides. In this study, it was found out that gaseous methyl iodide (CH 3 I) is oxidised when exposed to beta radiation in an oxygen containing atmosphere. As a result, nucleation of aerosol particles takes place and the formation of iodine oxide particles is suggested. These particles are highly hygroscopic. They take up water from the air humidity and iodine oxides dissolve within the droplets. In order to mitigate the possible source term, it is of interest to understand the effect of beta radiation on the speciation of iodine.

  19. Radiolytical oxidation of gaseous iodine by beta radiation

    Energy Technology Data Exchange (ETDEWEB)

    Kaerkelae, Teemu; Auvinen, Ari; Kekki, Tommi; Kotiluoto, Petri; Lyyraenen, Jussi [VTT Technical Research Centre of Finland, Espoo (Finland); Jokiniemi, Jorma [VTT Technical Research Centre of Finland, Espoo (Finland); Eastern Finland Univ., Kuopio (Finland)

    2015-07-01

    Iodine is one of the most radiotoxic fission product released from fuel during a severe nuclear power plant accident. Within the containment building, iodine compounds can react e.g. on the painted surfaces and form gaseous organic iodides. In this study, it was found out that gaseous methyl iodide (CH{sub 3}I) is oxidised when exposed to beta radiation in an oxygen containing atmosphere. As a result, nucleation of aerosol particles takes place and the formation of iodine oxide particles is suggested. These particles are highly hygroscopic. They take up water from the air humidity and iodine oxides dissolve within the droplets. In order to mitigate the possible source term, it is of interest to understand the effect of beta radiation on the speciation of iodine.

  20. Fly ash based zeolitic pigments for application in anticorrosive paints

    International Nuclear Information System (INIS)

    Shaw, Ruchi; Tiwari, Sangeeta

    2016-01-01

    The purpose of this work is to evaluate the utilization of waste fly ash in anticorrosive paints. Zeolite NaY was synthesized from waste fly ash and subsequently modified by exchanging its nominal cation Na + with Mg 2+ and Ca 2+ ions. The metal ion exchanged zeolite was then used as anticorrosive zeolitic pigments in paints. The prepared zeolite NaY was characterized using X-Ray diffraction technique and Scanning electron microscopy. The size, shape and density of the prepared fly ash based pigments were determined by various techniques. The paints were prepared by using fly ash based zeolitic pigments in epoxy resin and the percentages of pigments used in paints were 2% and 5%. These paints were applied to the mild steel panels and the anticorrosive properties of the pigments were assessed by the electrochemical spectroscopy technique (EIS).

  1. An experimental study on moisture absorption for jute-epoxy composite with coatings exposed to different pH media

    Directory of Open Access Journals (Sweden)

    Radhika Londhe

    2016-09-01

    The purpose of this work is to study the moisture absorption and mechanical properties of jute-epoxy composites. Jute fibres are treated with NaOH before manufacturing of composite laminate in order to improve adhesion with epoxy material. Further jute-epoxy composite specimens were coated with epoxy resin and acrylic paint. Composite specimens with and without coatings are subjected to absorption in solutions of different pH media, for 28 days (666 h. The effect of coatings on reduction in moisture absorption for jute-epoxy composite is presented in this current work.

  2. Evaluation of epoxy resin for cryogenic use by positron annihilation method. Change of characteristics of epoxy resin with cross-linking density and positron lifetime

    International Nuclear Information System (INIS)

    Nishijima, Shigehiro; Honda, Yoshihide; Okada, Toichi; Kobayashi, Yoshinori; Namba, Shingo.

    1994-01-01

    The positron annihilation method has been applied to evaluate unoccupied space in epoxy aiming at the design of the molecular structure for cryogenic use. To confirm the model in which molecular free space is needed in the epoxy for cryogenic use, the molecular weight between cross-linkings in epoxy was changed. The increase of molecular weight between cross-linkings brought an increase of fracture toughness even at liquid helium temperature and the model was found to be confirmed. The increase of molecular weight between cross-linkings was also found to decrease the 3rd lifetime of positrons. It suggested that the epoxy main chains were folded and this was confirmed by the molecular mechanical calculation. (author)

  3. A Simple and Convenient Method of Multiple Linear Regression to Calculate Iodine Molecular Constants

    Science.gov (United States)

    Cooper, Paul D.

    2010-01-01

    A new procedure using a student-friendly least-squares multiple linear-regression technique utilizing a function within Microsoft Excel is described that enables students to calculate molecular constants from the vibronic spectrum of iodine. This method is advantageous pedagogically as it calculates molecular constants for ground and excited…

  4. A study on impact monitoring using a piezoelectric paint sensor

    International Nuclear Information System (INIS)

    Choi, Kyung Woo; Kang, Dong Hoon; Park, Seung Bok; Kang, Lae Hyong

    2015-01-01

    The piezoelectric paint sensor is a paint type sensor comprising of an epoxy and piezoelectric powder, which is the main component of a piezoelectric material. This sensor can be easily attached to any type of structure as compared to other sensors because it is viable to directly apply it on structures, as in the case with a typical paint. In this study, the capability of piezoelectric paint sensor for impact detection was evaluated. In Particular, the applications of the piezoelectric paint sensor for railroad vehicles were considered. There have been various cases reported about the damages caused by flying gravel to the under-cover of the railroad vehicle during operation. In order to prevent this, real-time monitoring of the large under-cover surface of the railroad vehicle is unavoidable. Under the assumption of vehicle application, sensor sensitivities were measured after multiple and prolonged exposure to thermal cycle environment -20⁓60 degrees Celsius). Sensitivity evaluation of paint sensor under environmental conditions was conducted in an aluminum specimen. In results, despite the small variations in sensitivity, we could confirm the applicability of this paint sensor for impact detection even after a severe environmental exposure test

  5. Leaching test of bituminized waste and waste solidified by epoxy resin

    International Nuclear Information System (INIS)

    Yoshinaka, Kazuyuki; Sugaya, Atsushi; Onizawa, Toshikazu; Takano, Yugo; Kimura, Yukihiko

    2008-10-01

    About 30,000 bituminized waste drums and about 1800 drums of waste solidified by epoxy resin, generated from Tokai Reprocessing Plant, were stored in storage facilities. And study for disposal of these waste is performed. It was considered that radioactive nuclides and chemical components were released from these waste by contact of underground water, when disposed there waste. This paper is reported that result of leaching tests for these waste, done from 2003 to 2006. We've get precious knowledge and data, as follows. (1) In leaching tests for bituminized waste, it has detected iodine-129 peak, considered difficult too low energy gamma to detect. We've get data and knowledge of iodine-129 behavior first. Leached radioactivity for 50 days calculated by peak area was equal for about 40% and 100% of including radioactivity in bituminized waste sample. And we've get data of behavior of nitric acid ion and so on, important to study for disposal, in various condition of sample shape or leaching liquid temperature. (2) In leaching test for waste solidified by epoxy resin, we've get data of behavior of TBP, radionuclides and so on, important to study for disposal. Leached TBP was equal about 1% of including of sample. And we've get data of iodine-129 behavior, too. It was confirmed that leached iodine-129 was equal for about 60% and 100% of including sample, for 90 days. (author)

  6. Controlled interface between carbon fiber and epoxy by molecular self-assembly method

    International Nuclear Information System (INIS)

    He Jinmei; Huang Yudong; Liu Li; Cao Hailin

    2006-01-01

    In this paper, a new treatment method based on molecular self-assembly on carbon fiber surface was proposed for obtaining a controlled interface between carbon fiber and epoxy matrix in composite system. To form the controlled interfacial region, the surfaces of carbon fibers were first metallized by electroless Ag plating, then were reacted with a series of thiols (different chain lengths and terminally functional groups) to form self-assembly monolayers (SAMs), which further reacted with epoxy resin to generate a strong adhesion interface. The morphology, structure and composition of untreated and treated carbon fiber surface were investigated by atomic force microscope (AFM), surface-enhanced Raman scattering spectroscopy (SERS) and X-ray photoelectron spectroscopy (XPS), respectively. SERS study showed that thiols chemisorbed on Ag/carbon fiber in the form of thiolate species via the strong S-Ag coordinative bond. XPS study further confirmed the chemisorption by an S 2p 3/2 component observed at 162.2 eV. The binding energy was characteristic of silver thiolate. The interfacial shear strength of the carbon fiber/epoxy microcomposites was evaluated by the microbond technique. The results showed that there was a direct effect of the interfacial parameters changes such as chain lengths and surface functional groups on the fiber/matrix adhesion

  7. Comparison of Molecular Iodine Spectral Properties at 514.7 and 532 nm Wavelengths

    Directory of Open Access Journals (Sweden)

    Hrabina J.

    2014-08-01

    Full Text Available We present results of investigation and comparison of spectral properties of molecular iodine transitions in the spectral region of 514.7 nm that are suitable for laser frequency stabilization and metrology of length. Eight Doppler-broadened transitions that were not studied in detail before were investigated with the help of frequency doubled Yb-doped fiber laser, and three of the most promising lines were studied in detail with prospect of using them in frequency stabilization of new laser standards. The spectral properties of hyperfine components (linewidths, signal-to-noise ratio were compared with transitions that are well known and traditionally used for stabilization of frequency doubled Nd:YAG laser at the 532 nm region with the same molecular iodine absorption. The external frequency doubling arrangement with waveguide crystal and the Yb-doped fiber laser is also briefly described together with the observed effect of laser aging.

  8. A parametric study of surface roughness and bonding mechanisms of aluminum alloys with epoxies: a molecular dynamics simulation

    Science.gov (United States)

    Timilsina, Rajendra; Termaath, Stephanie

    The marine environment is highly aggressive towards most materials. However, aluminium-magnesium alloys (Al-Mg, specifically, 5xxx series) have exceptionally long service life in such aggressive marine environments. For instance, an Al-Mg alloy, AA5083, is extensively used in naval structures because of its good mechanical strength, formability, seawater corrosion resistance and weldability. However, bonding mechanisms of these alloys with epoxies in a rough surface environment are not fully understood yet. It requires a rigorous investigation at molecular or atomic levels. We performed a molecular dynamics simulation to study an adherend surface preparation and surface bonding mechanisms of Al-Mg alloy (AA5083) with different epoxies by developing several computer models. Various distributions of surface roughness are introduced in the models and performed molecular dynamics simulations. Formation of a beta phase (Al3Mg2) , microstructures, bonding energies at the interface, bonding strengths and durability are investigated. Office of Naval Research.

  9. Basis for and practical methods of controlling painting activities at the Sequoyah Nuclear Plant

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, R.R. [Tennessee Valley Authority, Chattanooga, TN (United States)

    1997-08-01

    Sequoyah Nuclear Plant (SQN) follows the guidance presented in Regulatory Guide (R.G.) 1.52, {open_quotes}Design, Testing, and Maintenance Criteria for Atmospheric Cleanup System Air Filtration and Adsorption System Units of Light-Water-Cooled Nuclear Power Plants{close_quotes} in protecting its charcoal filter trains from the effects of painting and other chemical releases. SQN, as well as other nuclear facilities around the country, have the problem of how to address the issue of protection of Engineered Safety Feature (ESF) filter systems from degradation due to communication with airborne hydrocarbons (i.e., primarily paints and solvents). R.G. 1.52 (and a similar statement from R.G. 1.140) states in part,{open_quotes}Testing should be performed ... following painting, fire, or chemical release in any ventilation zone communicating with the system...,{close_quotes} and requires that a test be performed upon any kind of painting or chemical release. This is considered overly restrictive if the activity is minor and in a location remote from the charcoal filters. Charcoal filters used in air cleaning systems are required to filter out radioactive iodine from an airstream before its release from the plant to the environment. Charcoal filters will age with time because of their ability to adsorb many different types of material. This aging affects the charcoal by lowering its iodine retention efficiency, and therefore the charcoal needs to be protected from the effects of chemicals such as paint fumes. 14 refs., 3 tabs.

  10. Extensive Evaluation of a Diffusion Denuder Technique for the Quantification of Atmospheric Stable and Radioactive Molecular Iodine

    DEFF Research Database (Denmark)

    Huang, Ru-Jin; Hou, Xiaolin; Hoffmann, Thorsten

    2010-01-01

    In this paper we present the evaluation and optimization of a new approach for the quantification of gaseous molecular iodine (I2) for laboratory- and field-based studies and its novel application for the measurement of radioactive molecular iodine. α-Cyclodextrin (α-CD) in combination with 129I......, and condition of release and derivatization of iodine, is extensively evaluated and optimized. The collection efficiency is larger than 98% and the limit of detection (LOD) obtained is 0.17 parts-per-trillion-by-volume (pptv) for a sampling duration of 30 min at 500 mL min−1. Furthermore, the potential use...... of this protocol for the determination of radioactive I2 at ultra trace level is also demonstrated when 129I− used in the coating is replaced by 127I− and a multiple denuder system is used. Using the present method we observed 25.7−108.6 pptv 127I2 at Mweenish Bay, Ireland and 108 molecule m−3 129I2 at Mainz...

  11. Wettability of nano-epoxies to UHMWPE fibers.

    Science.gov (United States)

    Neema, S; Salehi-Khojin, A; Zhamu, A; Zhong, W H; Jana, S; Gan, Y X

    2006-07-01

    Ultra high molecular weight polyethylene (UHMWPE) fibers have a unique combination of outstanding mechanical, physical, and chemical properties. However, as reinforcements for manufacturing high performance composite materials, UHMWPE fibers have poor wettability with most polymers. As a result, the interfacial bonding strength between the fibers and polymer matrices is very low. Recently, developing so-called nano-matrices containing reactive graphitic nanofibers (r-GNFs) has been proposed to promote the wetting of such matrices to certain types of fiber reinforcements. In this work, the wettability of UHMWPE fibers with different epoxy matrices including a nano-epoxy, and a pure epoxy was investigated. Systematic experimental work was conducted to determine the viscosity of the epoxies, the contact angle between the epoxies and the fibers. Also obtained are the surface energy of the fibers and the epoxies. The experimental results show that the wettability of the UHMWPE fibers with the nano-epoxy is much better than that of the UHMWPE fibers with the pure epoxy.

  12. Modeling an Iodine Hall Thruster Plume in the Iodine Satellite (ISAT)

    Science.gov (United States)

    Choi, Maria

    2016-01-01

    An iodine-operated 200-W Hall thruster plume has been simulated using a hybrid-PIC model to predict the spacecraft surface-plume interaction for spacecraft integration purposes. For validation of the model, the plasma potential, electron temperature, ion current flux, and ion number density of xenon propellant were compared with available measurement data at the nominal operating condition. To simulate iodine plasma, various collision cross sections were found and used in the model. While time-varying atomic iodine species (i.e., I, I+, I2+) information is provided by HPHall simulation at the discharge channel exit, the molecular iodine species (i.e., I2, I2+) are introduced as Maxwellian particles at the channel exit. Simulation results show that xenon and iodine plasma plumes appear to be very similar under the assumptions of the model. Assuming a sticking coefficient of unity, iodine deposition rate is estimated.

  13. Adsorption and revaporisation studies on iodine oxide aerosols deposited on containment surface materials in LWR

    International Nuclear Information System (INIS)

    Tietze, S.; Foreman, M.R.StJ.; Ekberg, C.; Kaerkelae, T.; Auvinen, A.; Tapper, U.; Lamminmaeki, S.; Jokiniemi, J.

    2012-12-01

    During a hypothetical severe nuclear accident, the radiation field will be very high in the nuclear reactor containment building. As a result gaseous radiolysis products will be formed. Elemental iodine can react in the gaseous phase with ozone to form solid iodine oxide aerosol particles (iodine oxide). Within the AIAS (Adsorption of Iodine oxide Aerosols on Surfaces) project the interactions of iodine oxide (IOx) aerosols with common containment surface materials were investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS, as well as Pt and Pd surfaces from hydrogen recombiners. Non-radioactive and 131 I labelled iodine oxide aerosols were produced with the EXSI CONT facility from elemental iodine and ozone at VTT Technical Research Centre of Finland. The iodine oxide deposits were analysed with microscopic and spectroscopic measurement techniques to identify the kind of iodine oxide formed and if a chemical conversion on the different surface materials occurs. The revaporisation behaviour of the deposited iodine oxide aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 having a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The revaporisated 131 I species from the surfaces were chemically tested for elemental iodine formation. The parameter dominating the degradation of the produced iodine oxide aerosols was humidity. Cu and Zn surfaces were found to react with iodine from the iodine oxide aerosols to form iodides, while no metal iodides were detected for Al and SS samples. Most of the iodine oxide aerosols are assumed to be

  14. Synthesis of cuprous oxide epoxy nanocomposite as an environmentally antimicrobial coating.

    Science.gov (United States)

    M El Saeed, Ashraf; Abd El-Fattah, M; Azzam, Ahmed M; Dardir, M M; Bader, Magd M

    2016-08-01

    Cuprous oxide is commonly used as a pigment; paint manufacturers begin to employ cuprous oxide as booster biocides in their formulations, to replace the banned organotins as the principal antifouling compounds. Epoxy coating was reinforced with cuprous oxide nanoparticles (Cu2O NPs). The antibacterial as well as antifungal activity of Cu2O epoxy nanocomposite (Cu2O EN) coating films was investigated. Cu2O NPs were also experimented for antibiofilm and time-kill assay. The thermal stability and the mechanical properties of Cu2O EN coating films were also investigated. The antimicrobial activity results showed slowdown, the growth of organisms on the Cu2O EN coating surface. TGA results showed that incorporating Cu2O NPs into epoxy coating considerably enhanced the thermal stability and increased the char residue. The addition of Cu2O NPs at lower concentration into epoxy coating also led to an improvement in the mechanical resistance such as scratch and abrasion. Cu2O NPs purity was confirmed by XRD. The TEM photograph demonstrated that the synthesized Cu2O NPs were of cubic shape and the average diameter of the crystals was around 25nm. The resulting perfect dispersion of Cu2O NPs in epoxy coating revealed by SEM ensured white particles embedded in the epoxy matrix. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Photoabsorption of the molecular IH cation at the iodine 3 d absorption edge

    Science.gov (United States)

    Klumpp, Stephan; Guda, Alexander A.; Schubert, Kaja; Mertens, Karolin; Hellhund, Jonas; Müller, Alfred; Schippers, Stefan; Bari, Sadia; Martins, Michael

    2018-03-01

    Yields of atomic iodine Iq + (q ≥2 ) fragments resulting from photoexcitation and photoionization of the target ions IH+ and I+ have been measured in the photon-energy range 610-680 eV, which comprises the thresholds for iodine 3 d ionization. The measured ion-yield spectra show two strong and broad resonance features due to the excitation of the 3 d3 /2 ,5 /2 electrons into ɛ f states rather similar for both parent ions. In the 3 d pre-edge range, excitations into (n p π ) -like orbitals and into an additional σ* orbital are found for IH+, which have been identified by comparison of the atomic I+ and molecular IH+ data and with the help of (time-dependent) density functional theory (DFT) and atomic Hartree-Fock calculations. The (5 p π ) orbital is almost atomlike, whereas all other resonances of the IH+ primary ion show a more pronounced molecular character, which is deduced from the chemical shifts of the resonances and the theoretical analysis.

  16. Antiproliferative/cytotoxic effects of molecular iodine, povidone-iodine and Lugol's solution in different human carcinoma cell lines.

    Science.gov (United States)

    Rösner, Harald; Möller, Wolfgang; Groebner, Sabine; Torremante, Pompilio

    2016-09-01

    Clinical trials have revealed that molecular iodine (I 2 ) has beneficial effects in fibrocystic breast disease and in cyclic mastalgia. Likewise, povidone-iodine (PVP-I), which is widely used in clinical practice as an antiseptic agent following tumour surgery, has been demonstrated to have cytotoxic effects on colon cancer and ascites tumour cells. Our previous study indicated that the growth of breast cancer and seven other human malignant cell lines was variably diminished by I 2 and iodolactones. With the intention of developing an iodine-based anticancer therapy, the present investigations extended these studies by comparing the cytotoxic capacities of I 2 , potassium iodide (KJ), PVP-I and Lugol's solution on various human carcinoma cell lines. Upon staining the cell nuclei with Hoechst 33342, the cell densities were determined microscopically. While KJ alone did not affect cell proliferation, it enhanced the antiproliferative activity of I 2 . In addition, PVP-I significantly inhibited the proliferation of human MCF-7 breast carcinoma, IPC melanoma, and A549 and H1299 lung carcinoma cells in a concentration corresponding to 20 µM I 2 . Likewise, Lugol's solution in concentrations corresponding to 20-80 µM I 2 were observed to reduce the growth of MCF-7 cells. Experiments with fresh human blood samples revealed that the antiproliferative activity of PVP-I and I 2 is preserved in blood plasma to a high degree. These findings suggest that PVP-I, Lugol's solution, and a combination of iodide and I 2 may be potent agents for use in the development of antitumour strategies.

  17. Simulation of ISTP-EPICUR Iodine Chemistry Tests with RAIM

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Han-Chul; Cho, Yeong-Hun; Jang, Dong-Ju; Ryu, Myung-Hyun [Nuclear Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2014-10-15

    The amount of iodine release largely depends on its volatility in the containment. Iodine has several chemical forms including aerosols, vapor, and gas. Among them gaseous iodine such as I{sub 2} and organic iodide are dominating due to their high volatility. Therefore, such iodine behavior has been extensively examined. Korea Institute of Nuclear Safety (KINS) has been joining the relevant international programs such as ISTP-EPICUR, OECD-BIP and OECD-STEM. In the course of this study, a simple iodine model, RAIM (Radio-Active Iodine chemistry Model) has been developed, based on the IMOD methodology and other previous studies. This model deals with chemical reactions associated with formation and destruction of iodine species in the containment atmosphere and the sump in a simple manner, as shown in Fig. 1. It also treats adsorption and desorption of volatile iodine on the paint surface. The iodine species modeled are inorganic volatile iodine, organic iodides of high volatility (HVRI) and low volatility (LVRI), non-volatiles, non-aqueous iodine, and iodine oxide aerosols (IO{sub x}). Many other material participating in the iodine reactions, e.g., air radiolysis products (ARP) such as ozone, are also modeled. This paper especially shows the analysis results after addition of gaseous reaction model to RAIM, which was further accompanied by adjustments of the existing reaction rate constants even for the aqueous reactions. After integration of iodine reaction models for gas and aqueous phase, RAIM was applied the S1-9 and S1-11 tests which were carried out in aqueous phase. In addition, re-analysis of the S2-6-5-2 test, for which iodine-loaded coupons were tested in gas phase, was also performed.

  18. Iodine oxides in large-scale THAI tests

    International Nuclear Information System (INIS)

    Funke, F.; Langrock, G.; Kanzleiter, T.; Poss, G.; Fischer, K.; Kühnel, A.; Weber, G.; Allelein, H.-J.

    2012-01-01

    Highlights: ► Iodine oxide particles were produced from gaseous iodine and ozone. ► Ozone replaced the effect of ionizing radiation in the large-scale THAI facility. ► The mean diameter of the iodine oxide particles was about 0.35 μm. ► Particle formation was faster than the chemical reaction between iodine and ozone. ► Deposition of iodine oxide particles was slow in the absence of other aerosols. - Abstract: The conversion of gaseous molecular iodine into iodine oxide aerosols has significant relevance in the understanding of the fission product iodine volatility in a LWR containment during severe accidents. In containment, the high radiation field caused by fission products released from the reactor core induces radiolytic oxidation into iodine oxides. To study the characteristics and the behaviour of iodine oxides in large scale, two THAI tests Iod-13 and Iod-14 were performed, simulating radiolytic oxidation of molecular iodine by reaction of iodine with ozone, with ozone injected from an ozone generator. The observed iodine oxides form submicron particles with mean volume-related diameters of about 0.35 μm and show low deposition rates in the THAI tests performed in the absence of other nuclear aerosols. Formation of iodine aerosols from gaseous precursors iodine and ozone is fast as compared to their chemical interaction. The current approach in empirical iodine containment behaviour models in severe accidents, including the radiolytic production of I 2 -oxidizing agents followed by the I 2 oxidation itself, is confirmed by these THAI tests.

  19. Gas phase reactions of organic iodine in containment conditions

    International Nuclear Information System (INIS)

    Kaerkalae, T.; Holm, J.; Auvinen, A.; Zilliacus, R.; Kajolinna, T.; Tapper, U.; Gaenneskog, H.; Ekberg, C.

    2010-01-01

    In case of a hypothetical severe accident it is very likely that iodine at least partly deposits on painted walls of a reactor containment building. Iodine may react with painted surfaces to form organic iodine species. These organic species are a possible source of volatile iodine, which may increase the fraction of releasable iodine. Therefore, it is important to study the transport of organic iodine in containment conditions. Another question is, in which form are the organic iodides transported as gaseous molecules or as aerosol particles resulting from organic iodides reacting with radiolysis products. To answer this last question methyl iodide was fed into the EXSI facility in an air mixture. In some experiments the flow contained also humidity. The reactions took place in a quartz tube heated either to 50 deg. C, 90 deg. C or 120 deg. C. UV-light was used as a source of radiation to produce ozone from oxygen. A separate generator was also applied to reach higher ozone concentrations. Nucleated aerosol particles were collected on plane filters and gaseous iodine species were trapped in trapping bottles. Aerosol mass flow rate and size distribution as well as speciation of gaseous reaction products were measured with several on-line instruments. Collected aerosol particles were analysed with SEM. It was found that the formation of aerosol particles was very fast when ozone and methyl iodide were present in the facility. Even a very low concentration of ozone produced high number concentration of particles. The measured aerosol mass concentration increased with increasing temperature and ozone concentration. Because the particle diameter was quite small (<180 nm), their settling velocity is low. Therefore, iodine containing aerosols may exist in containment atmosphere for a long period of time. Part of methyl iodide was always transported through the facility regardless of experimental conditions. All ozone was consumed in the reactions when only UV-light was

  20. Molecular Imaging of Cancer Using X-ray Computed Tomography with Protease Targeted Iodinated Activity-Based Probes.

    Science.gov (United States)

    Gaikwad, Hanmant K; Tsvirkun, Darya; Ben-Nun, Yael; Merquiol, Emmanuelle; Popovtzer, Rachela; Blum, Galia

    2018-03-14

    X-ray computed tomography (CT) is a robust, precise, fast, and reliable imaging method that enables excellent spatial resolution and quantification of contrast agents throughout the body. However, CT is largely inadequate for molecular imaging applications due mainly to its low contrast sensitivity that forces the use of large concentrations of contrast agents for detection. To overcome this limitation, we generated a new class of iodinated nanoscale activity-based probes (IN-ABPs) that sufficiently accumulates at the target site by covalently binding cysteine cathepsins that are exceptionally highly expressed in cancer. The IN-ABPs are comprised of a short targeting peptide selective to specific cathepsins, an electrophilic moiety that allows activity-dependent covalent binding, and tags containing dendrimers with up to 48 iodine atoms. IN-ABPs selectively bind and inhibit activity of recombinant and intracellular cathepsin B, L, and S. We compared the in vivo kinetics, biodistribution, and tumor accumulation of IN-ABPs bearing 18 and 48 iodine atoms each, and their control counterparts lacking the targeting moiety. Here we show that although both IN-ABPs bind specifically to cathepsins within the tumor and produce detectable CT contrast, the 48-iodine bearing IN-ABP was found to be optimal with signals over 2.1-fold higher than its nontargeted counterpart. In conclusion, this study shows the synthetic feasibility and potential utility of IN-ABPs as potent contrast agents that enable molecular imaging of tumors using CT.

  1. Paint and binding material to be hardened by ionizing radiations

    International Nuclear Information System (INIS)

    Johnson, O.B.; Labana, S.S.

    1976-01-01

    The invention concerns a paint binding material which can be hardened due to the effect of ionising radiation, consisting of a dispersion of a) an ethylene unsaturated material in b) at least one vinyl monomer. Component (a) is a reaction product of graded rubber particles (0.1 - 4 μm) and an ethylene unsaturated component with a reactive epoxy-, hydroxy- or carbonyl-group, which is connected to the rubber by ester or urethane links. The rubber particles have a core of cross linked elastomer acrylic polymers, an outer shell of reactive groups and an intermediate layer made from the core monomer and the shell. 157 examples explain the manufacturing process. The paint is suitable for covering articles which will later be subject to distortion. (UWI) [de

  2. Absorption of gaseous iodine by water droplets

    International Nuclear Information System (INIS)

    Albert, M.F.

    1985-07-01

    A new model has been developed for predicting the rate at which gaseous molecular iodine is absorbed by water sprays. The model is a quasi-steady state mass transfer model that includes the iodine hydrolysis reactions. The parameters of the model are spray drop size, initial concentration of the gas and liquid phases, temperature, pressure, buffered or unbuffered spray solution, spray flow rate, containment diameter and drop fall height. The results of the model were studied under many values of these parameters. Plots of concentration of iodine species in the drop versus time have been produced by varying the initial gas phase concentration of molecular iodine over the range of 1 x 10 -5 moles/liter to 1 x 10 -10 moles/liter and a drop size of 1000 microns. Results from the model are compared to results available from Containment Systems Experiments at Pacific Northwest Laboratory. The difference between the model predictions and the experimental data ranges from -120.5% to 68.0% with the closest agreement 7.7%. The new spray model is also compared to previously existing spray models. At high concentrations of gaseous molecular iodine, the new spray model is considered to be less accurate but at low concentrations, the new model predicts results that are closer to the experimental data than the model called the realistic model from WASH-1329. Inclusion of the iodine hydrolysis reaction is shown to be a feature important to a model intended for determining the removal of molecular iodine over a wide range of conditions

  3. Present status of iodine research at IPSN

    Energy Technology Data Exchange (ETDEWEB)

    Bardelay, J [IPSN/DPEA/SEAC (France)

    1996-12-01

    Since several years, IPSN has conducted an effort in order to evaluate the release of radioactive iodine in case of hypothetical severe accident in a realistic manner. This source-term evaluation is performed with IODE code which is a module of the EXCADRE system of codes. This code is validated against: -analytical experiments: in these experiments, IPSN studies radiolytic effects and chemical processes in the sump, organic formation, mass transfer, effect of spray (CARAIDAS experiment), - the CAIMAN semi global experiment; this experiment will allow to study the phenomena linked to iodine behavior under representative containment geometry in the presence of painted surfaces and global irradiation, - the PHEBUS FP program. The paper consists to describe succinctly the current status of IODE and the various experiments for its validation. In case of hypothetical severe accident iodine can induce important perturbations of human organism. The effects are principally radiological, in particular on the thyroid. At short term, radioactive iodine is the most important contributor for the sanitary risk. It represents 55% of effective dose and 92% of thyroid dose at 10 km in case of controlled rejects with current assumptions. This is the reason why it must be actively studied. In France, the safety evaluations are performed with mechanistic codes or lumped parameter codes like EXCADRE which contains a module devoted to iodine studies: IODINE. The objective of the French experimental program on iodine is to understand and quantify important phenomena in order to put kinetic parameters in IODE module. The experiments can be classified in analytical experiments, the semi-global experiment CAIMAN which takes into account different phenomena studied in analytical experiments and the global experiment PHEBUS PF, not only devoted to iodine behavior study. In the following text we will present the needs of IODINE code and these different experiments. (author).

  4. Present status of iodine research at IPSN

    International Nuclear Information System (INIS)

    Bardelay, J.

    1996-01-01

    Since several years, IPSN has conducted an effort in order to evaluate the release of radioactive iodine in case of hypothetical severe accident in a realistic manner. This source-term evaluation is performed with IODE code which is a module of the EXCADRE system of codes. This code is validated against: -analytical experiments: in these experiments, IPSN studies radiolytic effects and chemical processes in the sump, organic formation, mass transfer, effect of spray (CARAIDAS experiment), - the CAIMAN semi global experiment; this experiment will allow to study the phenomena linked to iodine behavior under representative containment geometry in the presence of painted surfaces and global irradiation, - the PHEBUS FP program. The paper consists to describe succinctly the current status of IODE and the various experiments for its validation. In case of hypothetical severe accident iodine can induce important perturbations of human organism. The effects are principally radiological, in particular on the thyroid. At short term, radioactive iodine is the most important contributor for the sanitary risk. It represents 55% of effective dose and 92% of thyroid dose at 10 km in case of controlled rejects with current assumptions. This is the reason why it must be actively studied. In France, the safety evaluations are performed with mechanistic codes or lumped parameter codes like EXCADRE which contains a module devoted to iodine studies: IODINE. The objective of the French experimental program on iodine is to understand and quantify important phenomena in order to put kinetic parameters in IODE module. The experiments can be classified in analytical experiments, the semi-global experiment CAIMAN which takes into account different phenomena studied in analytical experiments and the global experiment PHEBUS PF, not only devoted to iodine behavior study. In the following text we will present the needs of IODINE code and these different experiments. (author)

  5. Iodine behaviour in PWR accidents leading to severe core damage

    International Nuclear Information System (INIS)

    Lucas, M.; Devillers, C.; Fermandjian, J.; Manesse, D.

    1982-09-01

    This paper deals with the iodine partition coefficient between the water at the bottom of the reactor building and the atmosphere above it. Molecular iodine is considered as a potential contributor to the airborne activity inside the reactor building. The concentration of molecular iodine in the containment atmosphere will depend, on one hand, upon mechanisms which generate that species and, on the other hand, upon the kinetics of chemical reactions which consume that species. Experiments have therefore been performed on the two following items: - molecular iodine formation through ν radiation from cesium iodide aerosols (droplets) in the reactor containment building, for doses ranging between 1.2 and 8 MRad (12 and 80 kSv), with solutions of various pH's and at different temperatures, - rate of hypoiodous acid disproportionation into iodate and iodide influencing further behavior of molecular iodine

  6. Adsorption and revaporisation studies on iodine oxide aerosols deposited on containment surface materials in LWR

    Energy Technology Data Exchange (ETDEWEB)

    Tietze, S.; Foreman, M.R.StJ.; Ekberg, C. [Chalmers Univ. of Technology, Goeteborg (Sweden); Kaerkelae, T.; Auvinen, A.; Tapper, U.; Lamminmaeki, S.; Jokiniemi, J. [VTT Technical Research Centre of Finland, Espoo (Finland)

    2012-12-15

    During a hypothetical severe nuclear accident, the radiation field will be very high in the nuclear reactor containment building. As a result gaseous radiolysis products will be formed. Elemental iodine can react in the gaseous phase with ozone to form solid iodine oxide aerosol particles (iodine oxide). Within the AIAS (Adsorption of Iodine oxide Aerosols on Surfaces) project the interactions of iodine oxide (IOx) aerosols with common containment surface materials were investigated. Common surface materials in Swedish and Finnish LWRs are Teknopox Aqua V A paint films and metal surfaces such as Cu, Zn, Al and SS, as well as Pt and Pd surfaces from hydrogen recombiners. Non-radioactive and {sup 131}I labelled iodine oxide aerosols were produced with the EXSI CONT facility from elemental iodine and ozone at VTT Technical Research Centre of Finland. The iodine oxide deposits were analysed with microscopic and spectroscopic measurement techniques to identify the kind of iodine oxide formed and if a chemical conversion on the different surface materials occurs. The revaporisation behaviour of the deposited iodine oxide aerosol particles from the different surface materials was studied under the influence of heat, humidity and gamma irradiation at Chalmers University of Technology, Sweden. Studies on the effects of humidity were performed using the FOMICAG facility, while heat and irradiation experiments were performed in a thermostated heating block and with a gammacell 22 having a dose rate of 14 kGy/h. The revaporisation losses were measured using a HPGe detector. The revaporisated {sup 131}I species from the surfaces were chemically tested for elemental iodine formation. The parameter dominating the degradation of the produced iodine oxide aerosols was humidity. Cu and Zn surfaces were found to react with iodine from the iodine oxide aerosols to form iodides, while no metal iodides were detected for Al and SS samples. Most of the iodine oxide aerosols are assumed to

  7. Study of Iodine Behavior in the Gas Phase during a Severe Accident

    International Nuclear Information System (INIS)

    Kim, Hanchul; Cho, Yeonghun; Ryu, Myunghyun

    2014-01-01

    Among the iodine species, the organic iodides produced from the reaction between iodine and organics such as paint, are not easily trapped by the filters during the containment venting following a severe accident. Korea Institute of Nuclear Safety (KINS) has been studying this issue, joining international research programs such as ISTP-EPICUR, OECDBIP and OECD-STEM. In the course of this study, a simple iodine model, RAIM (Radio-Active Iodine chemistry Model) has been developed (Oh et al., 2011), based on the IMOD methodology, and other previous studies. This paper deals with our recent activities on this study, including the development of the model for the iodine reactions in gas phase. Iodine reactions in gas phase were modeled and added to the RAIM code, taking into account several relevant reactions such as formation of ARP, iodine oxide, and organic iodides in gas phase. RAIM was then applied to analyze the S2-6-5-2 test for which iodine-loaded coupons were tested in gas phase. The analysis results show a reasonable estimation of volatile iodine concentration with the desorption rate constant of about 10 -6 s -1 , while those of the other iodine species overestimated for the whole period of the test. It reveals the need to determine appropriate values for the rate constants for formation of iodine oxides and organic iodides

  8. ELABORATION OF AN EPOXY COATING REINFORCED WITH ZIRCONIUM CARBIDE NANOSTRUCTURES

    Directory of Open Access Journals (Sweden)

    Lucia G. Díaz-Barriga

    2013-12-01

    Full Text Available This work shows the preparation of a transparent epoxy coating reinforced with 200 PPM of zirconium carbide nanostructures. The nanostructures of ZrC were prepared by mechanosynthesis. The additive characteristics analyzed by X-ray diffraction (XRD and scanning electron microscopy (SEM were presented. Epoxy coating adhesion on a steel plate was analyzed using MEB. Thermogravimetric analysis (TGA was performed to the reinforced paints between 20-700 °C. The reinforced enamel was compared with an enamel without nanostructures. There is not vaporization of reinforced enamel at a 95 y 100 °C with ZrC particles size of 10 µm y 120 nm respectively. The final enamel degradation is slower when there is a 14% by weight of the residue and 426 °C with 120nm diameter particles.

  9. 124Iodine: A Longer-Life Positron Emitter Isotope—New Opportunities in Molecular Imaging

    Directory of Open Access Journals (Sweden)

    Giuseppe Lucio Cascini

    2014-01-01

    Full Text Available 124Iodine (124I with its 4.2 d half-life is particularly attractive for in vivo detection and quantification of longer-term biological and physiological processes; the long half-life of 124I is especially suited for prolonged time in vivo studies of high molecular weight compounds uptake. Numerous small molecules and larger compounds like proteins and antibodies have been successfully labeled with 124I. Advances in radionuclide production allow the effective availability of sufficient quantities of 124I on small biomedical cyclotrons for molecular imaging purposes. Radioiodination chemistry with 124I relies on well-established radioiodine labeling methods, which consists mainly in nucleophilic and electrophilic substitution reactions. The physical characteristics of 124I permit taking advantages of the higher PET image quality. The availability of new molecules that may be targeted with 124I represents one of the more interesting reasons for the attention in nuclear medicine. We aim to discuss all iodine radioisotopes application focusing on 124I, which seems to be the most promising for its half-life, radiation emissions, and stability, allowing several applications in oncological and nononcological fields.

  10. Influence of the molecular structure on hydrolyzability of epoxy resins

    International Nuclear Information System (INIS)

    Pays, M.F.

    1996-01-01

    EDF has decided to use glass reinforced composites for certain pipework in Pressurized Water Reactors (service water, emergency-supplied service water, fine pipe works, etc...) as a replacement for traditional materials. In practice, steel is prone to rapid corrosion in these circuits; introducing composites could prove economically viable if their long term behaviour can be demonstrated. However, composite materials can undergo deterioration in service through hydrolysis of the resin or the fibre-matrix interface. Different resins can be chosen depending on the programmed use. A first study has covered the hydrolyzability of polyester and vinyl ester resins. The present document undertakes the resistance to hydrolysis of epoxy resins, concentrating on those reputed to withstand high temperatures. This research uses model monomer, linking the molecular structure of the materials to their resistance to hydrolysis. (author)

  11. Spectroscopic and structural study of novel interaction product of pyrrolidine-2-thione with molecular iodine. Presumable mechanisms of oxidation

    Science.gov (United States)

    Chernov'yants, Margarita S.; Burykin, Igor V.; Starikova, Zoya A.; Tereznikov, Alexander Yu.; Kolesnikova, Tatiana S.

    2013-09-01

    Synthesis, spectroscopic and structural characterization of novel interaction product of pyrrolidine-2-thione with molecular iodine is reported. The ability of pyrrolidine-2-thione to form the outer-sphere charge-transfer complex C4H7NS·I2 with iodine molecule in dilute chloroform solution has been studied by UV/vis spectroscopy. Oxidative desulfurization promotes ring fusion of two pyrrolidine-2-thione molecules. The product of iodine induced oxidative desulfurization has been studied by X-ray diffraction method. The crystal structure of the reaction product is formed by 5-(2-thioxopyrrolidine-1-yl)-3,4-dihydro-2H-pyrrolium (C8H13N2S+) cations and pentaiodide anions I5-, which are linked by the intermolecular I⋯Hsbnd C and I⋯C close contacts. The angular pentaiodide anions can be considered as structures formed by coordination of two iodine molecules to the iodide ion (type 1) or by the coordination of iodine molecule to the triiodide ion (type 2).

  12. Iodine Plasma (Electric Propulsion) Interaction with Spacecraft Materials

    Science.gov (United States)

    2016-12-28

    Teflon (AGT5, Ag-FEP) Thermal control surface (radiator) Spacecraft Exposure Soda-lime glass (74% SiO2 , 13% Na2O, 8% CaO, 4% MgO, 1% other oxide... Glass Solar panel cover Spacecraft Exposure Buna-N (acrylonitrile butadiene rubber) Seals Iodine Feed System Carbon fiber composite (epoxy resin...Fe Propellant isolator Spacecraft Exposure Lanthanum Hexaboride, LaB6 Cathode emitter Inside Cathode Yes MACOR (46% SiO2 , 17% MgO, 16% Al2O3, 10

  13. The kinetic study of oxidation of iodine by hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Cantrel, L [Institut de Protection et de Surete Nucleaire, IPNS, CEN Cadarache, Saint Paul lez Durance (France); Chopin, J [Laboratoire d` Electrochimie Inorganique, ENSSPICAM, Marseille (France)

    1996-12-01

    Iodine chemistry is one of the most important subjects of research in the field of reactor safety because this element can form volatile species which represent a biological hazard for environment. As the iodine and the peroxide are both present in the sump of the containment in the event of a severe accident on a light water nuclear reactor, it can be important to improve the knowledge on the reaction of oxidation of iodine by hydrogen peroxide. The kinetics of iodine by hydrogen peroxide has been studied in acid solution using two different analytical methods. The first is a UV/Vis spectrophotometer which records the transmitted intensity at 460 nm as a function of time to follow the decrease of iodine concentration, the second is an amperometric method which permits to record the increase of iodine+1 with time thanks to the current of reduction of iodine+1 to molecular iodine. The iodine was generated by Dushman reaction and the series of investigations were made at 40{sup o}C in a continuous stirring tank reactor. The influence of the initial concentrations of iodine, iodate, hydrogen peroxide, H{sup +} ions has been determined. The kinetics curves comprise two distinct chemical phases both for molecular iodine and for iodine+1. The relative importance of the two processes is connected to the initial concentrations of [I{sub 2}], [IO{sub 3}{sup -}], [H{sub 2}O{sub 2}] and [H{sup +}]. A rate law has been determined for the two steps for molecular iodine. (author) figs., tabs., 22 refs.

  14. The kinetic study of oxidation of iodine by hydrogen peroxide

    International Nuclear Information System (INIS)

    Cantrel, L.; Chopin, J.

    1996-01-01

    Iodine chemistry is one of the most important subjects of research in the field of reactor safety because this element can form volatile species which represent a biological hazard for environment. As the iodine and the peroxide are both present in the sump of the containment in the event of a severe accident on a light water nuclear reactor, it can be important to improve the knowledge on the reaction of oxidation of iodine by hydrogen peroxide. The kinetics of iodine by hydrogen peroxide has been studied in acid solution using two different analytical methods. The first is a UV/Vis spectrophotometer which records the transmitted intensity at 460 nm as a function of time to follow the decrease of iodine concentration, the second is an amperometric method which permits to record the increase of iodine+1 with time thanks to the current of reduction of iodine+1 to molecular iodine. The iodine was generated by Dushman reaction and the series of investigations were made at 40 o C in a continuous stirring tank reactor. The influence of the initial concentrations of iodine, iodate, hydrogen peroxide, H + ions has been determined. The kinetics curves comprise two distinct chemical phases both for molecular iodine and for iodine+1. The relative importance of the two processes is connected to the initial concentrations of [I 2 ], [IO 3 - ], [H 2 O 2 ] and [H + ]. A rate law has been determined for the two steps for molecular iodine. (author) figs., tabs., 22 refs

  15. Studies on Fracture Behavior of Epoxy/DWNT Nanocomposites by Molecular Dynamics Simulation

    Directory of Open Access Journals (Sweden)

    Shahin Shadlou

    2012-12-01

    Full Text Available The nanoscale fracture behavior of epoxy-based nanocomposites reinforced with double-walled carbon nanotube (DWNT was investigated by molecular dynamics (MD simulations technique. In order to prepare a nanocomposite model including polymer and DWNT, the exact atomic structure of epoxy was adopted as in previous experimental studies made by authors. Tersoff and Amber potential, which are well known potentials, were used for simulation of polymer and DWNT, respectively. Among different available methods to simulate the cross-linking process, a technique was adopted with closer similarity to what happens in real conditions. Therefore, when some especial atoms of monomer and hardener molecules were closer than a specific potential distance, the chemical bonds were created between them. To verify the prepared model, a pull-out simulation was carried out and the results were compared with those of previous studies. It was found that although a rather wide range for interface strength has been presented by different researchers and different techniques, the strength obtained in this study is in the middle of this range. In addition, the fracture energy obtained from the simulations for pure epoxy was compared with that of experimental results and good agreement was obtained. To evaluate the effect of nanocomposite structure at nanometer scale, DWNT was modeled in three different angles relative to the loading direction, including 0°, 45°and 90°. It was found that when DWNT is parallel with the loading direction (i.e. 90° it has the least impact on the fracture energy. The maximum fracture energy was obtained when MWNT was at 45° relative to loading direction. These results were compared with the theories provided for conventional composites.

  16. Epoxy/anhydride thermosets modified with end-capped star polymers with poly(ethyleneimine cores of different molecular weight and poly(ε–caprolactone arms

    Directory of Open Access Journals (Sweden)

    C. Acebo

    2015-09-01

    Full Text Available Multiarm star polymers, with a hyperbranched poly(ethyleneimine (PEI core and poly(ε-caprolactone (PCL arms end-capped with acetyl groups were synthesized by ring-opening polymerization of ε-caprolactone from PEI cores of different molecular weight. These star polymers were used as toughening agents for epoxy/anhydride thermosets. The curing process was studied by calorimetry, thermomechanical analysis and infrared spectroscopy. The final properties of the resulting materials were determined by thermal and mechanical tests. The addition of the star polymers led to an improvement up to 130% on impact strength and a reduction in the thermal stresses up to 55%. The structure and molecular weight of the modifier used affected the morphology of the resulting materials. Electron microscopy showed phase-separated morphologies with nano-sized fine particles well adhered to the epoxy/anhydride matrix when the higher molecular weight modifier was used.

  17. LWR severe accident simulation: Iodine behaviour in FPT2 experiment and advances on containment iodine chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Girault, N., E-mail: nathalie.girault@irsn.fr [Institut de Radioprotection et de Surete Nucleaire (IRSN), BP3 - 13115 St.-Paul-lez-Durance (France); Bosland, L. [Institut de Radioprotection et de Surete Nucleaire (IRSN), BP3 - 13115 St.-Paul-lez-Durance (France); Dickinson, S. [National Nuclear Laboratory, Harwell, Oxon OX11 0QT (United Kingdom); Funke, F. [AREVA NP Gmbh, PO Box 1109, 91001 Erlangen (Germany); Guentay, S. [Paul Scherrer Institut, 5232 Villigen PSI (Switzerland); Herranz, L.E. [Centro des Investigaciones Energeticas, MedioAmbiantales y Tecnologicas, av. Complutense 2, 28040 Madrid (Spain); Powers, D. [Sandia National Laboratories, New Mexico, PO Box 5800, Albuquerque, NM 87185 (United States)

    2012-02-15

    the iodine behaviour in the FPT2 containment vessel based on dedicated small-scale analytical experiments and computer codes calculations. Other investigations dealing with primary circuit and sump chemistry are also reported. These could help to scale the results of Phebus-FP tests to reactor accidents. Modelling studies were generally successful when a gaseous iodine injection from the primary circuit was assumed. Indeed, though each of the iodine codes has specific iodine chemistry features that should be further developed and each approach to the modelling is distinct, the overall iodine behaviour in the FPT2 containment is generally well reproduced by the models that predict: Bullet a low final gaseous iodine concentration in the containment atmosphere, Bullet a predominant iodine concentration in the sump and to a lesser extent a significant iodine deposition on containment surfaces. The main code-to-code differences, in the results obtained in gaseous iodine speciation, come from the various treatments of gaseous radiolytic reactions. Calculations that include the radiolytic conversion of volatile iodine into iodine oxide particulate show there is a persistence of both gaseous iodine and iodine oxide particles in the atmosphere. There are also some variations between the predicted organic iodine concentrations that depend mainly on the initial assumptions. A key aspect of the Phebus FPT2 test interpretation is that the long term iodine behaviour in the containment can be explained by exchanges between organic iodide released from painted surfaces and inorganic iodine released from deposited aerosol on the containment walls. Further studies of regulatory significance on sump chemistry showed that the gaseous iodine control that was evident in the Phebus tests through silver release and/or alkaline buffered sump solutions may not be assured. As most of the past iodine aqueous chemistry studies were done with rather pure systems and because of the uncompleted

  18. A Highly Sensitive Electrochemical Glucose Sensor By Nickel-Epoxy Electrode With Non-Enzymatic Sensor

    Directory of Open Access Journals (Sweden)

    Riyanto Riyanto

    2016-03-01

    Full Text Available The preparation of new sensor for glucose was based on the fact that glucose can be determined by non-enzymatic glucose oxidase. The Ni metals (99.98% purity, 0.5 mm thick, Aldrich Chemical Company was used to prepare Ni-Epoxy electrode. The Ni-epoxy electrodes were prepared in square cut of 1 cm and 1 mm by length and wide respectively. The Ni metal electrodes were connected to silver wire with silver conducting paint prior covered with epoxy gum. The prepared of nickel-epoxy modified electrode showed outstanding electro catalytic activity toward the oxidation of glucose in alkaline solution. The result from this research are correlation of determination using Nickel-Epoxyelectrode for electroanalysis of glucose in NaOH was R2 = 0.9984. LOQ, LOD and recovery of the Nickel-Epoxy electrode towards glucose were found to be 4.4 μM, 1.48 μM and 98.19%, respectively. The Nickel-Epoxy wire based electrochemical glucose sensor demonstrates good sensitivity, wide linear range, outstanding detection limit, attractive selectivity, good reproducibility, high stability as well as prominent feasibility use of non-enzymatic sensor for monitoring glucose in human urine owing to its advantages of low cost, simple preparation and excellent properties for glucose detection.

  19. The method of quantitative determination of iodine in acetic acid

    International Nuclear Information System (INIS)

    Sukhomlinov, A.B.; Kalinchenko, N.B.

    1988-01-01

    Method for separate determination of J 2 and J - concentrations in acetic acid is suggested. Iodine concentration in acetic acid is determined by measuring potential of iodine-selective electrode first in the initial solution of acetic acid, where molecular iodine dissociation equals 0.5, and then in acetic acid, with alkali (NaOH) addition up to pH > 3, where molecular iodine dissociation equals 1. Determination is conducted in 5x10 -7 -5x10 -6 mol/l concentration range with relative standard deviation not more than 0.1. 1 fig

  20. A randomized open-label controlled trial of chlorhexidine-alcohol vs povidone-iodine for cesarean antisepsis: the CAPICA trial.

    Science.gov (United States)

    Springel, Edward H; Wang, Xiao-Yu; Sarfoh, Vanessa M; Stetzer, Bradley P; Weight, Steven A; Mercer, Brian M

    2017-10-01

    Identification of optimal surgical site antisepsis preparations may reduce cesarean-related surgical site infections. Two recently published investigations examined efficacy of chlorhexidine-alcohol and iodine-alcohol preparations. No previous randomized controlled trial has compared chlorhexidine-alcohol to povidone-iodine aqueous scrub and paint in reduction of cesarean-related surgical site infection. The purpose of the study was to determine if chlorhexidine-alcohol would result in fewer surgical site infections than povidone-iodine when used as skin antisepsis preparation prior to cesarean delivery. This study was a single-center pragmatic randomized controlled trial at an urban tertiary care institution to compare chlorhexidine-alcohol 26-mL single-step applicator to povidone-iodine aqueous scrub and paint 236-mL wet skin tray as preoperative skin antiseptic preparation for women undergoing cesarean delivery. Patients were eligible for study participation if they could provide informed consent in English or Spanish, were ≥18 years of age, did not have clinical chorioamnionitis, were unlikely to be lost to follow-up, and had no sensitivities to chlorhexidine, betadine, or iodine. Treatment was assigned by computer-generated simple 1:1 randomization immediately before skin preparation. The primary outcome was surgical site infection occurring within 30 days of cesarean delivery including ≥1 of: superficial or deep surgical site infection, or endometritis, according to Centers for Disease Control and Prevention definitions. Analysis was by intent to treat. Categorical outcomes were compared using Fisher exact test. The Wilcoxon rank-sum test was performed for continuous outcomes. This trial was institutional review board approved and registered at ClinicalTrials.gov (NCT02202577). In all, 932 subjects (461 assigned to chlorhexidine-alcohol, 471 assigned to povidone-iodine) were randomized from February 2013 through May 2016. Rate of follow-up evaluation

  1. Laboratory studies on tropospheric iodine chemistry: bridging the atomic, molecular and particle scale

    Science.gov (United States)

    Gomez Martin, J.; Saunders, R. W.; Blitz, M. A.; Mahajan, A. S.; Plane, J. M.

    2008-12-01

    High mixing ratios of the iodine oxides IO and OIO have been observed in the polar, mid-latitude and tropical marine boundary layer (MBL). The impact of the iodine chemistry on the oxidizing capacity of the MBL is well documented. Moreover, there is evidence showing that the bursts of new particles measured in coastal regions are produced by the biogenic emission of iodine containing precursors, followed by the photochemical production and condensation of iodine oxide vapours. Airborne measurements of particle growth rates show that these particles can reach significant sizes where they can contribute to the regional aerosol loading, thus suggesting a potential impact on climate on a regional or global scale. Within the frame of the INSPECT project (INorganic Secondary Particle Evolution, Chemistry and Transport) we wish to understand at a fundamental level the tendency for the iodine oxides formed from IO and OIO recombination to condense into particles. Elemental analysis of iodine oxide particles (IOP) made in the laboratory shows that they have the empirical formula I2O5. The major question is how this happens: through formation of I2O5 in the gas phase, followed by polymerization, or by condensation of various IxOy to form amorphous iodine oxides, which subsequently rearrange to I2O5. We are studying the gas phase photochemistry leading to nucleation of IOP, their growth kinetics, aspects of their heterogeneous chemistry, and their properties as ice condensation nuclei. In order to bridge the molecular and the particle scales, a wide variety of techniques are being used, including CRDS, ARAS, LIF, UV-VIS spectroscopy, PI-TOF-MS and mobility particle size scanning. The results obtained so far provide new and interesting insights to the problem. From the gas phase point of view, a unit iodine atom quantum yield from OIO photolysis has been now established across its strong visible spectral bands. This result implies a short lifetime of OIO and explains why in

  2. Atomistic modeling of thermomechanical properties of SWNT/Epoxy nanocomposites

    Science.gov (United States)

    Fasanella, Nicholas; Sundararaghavan, Veera

    2015-09-01

    Molecular dynamics simulations are performed to compute thermomechanical properties of cured epoxy resins reinforced with pristine and covalently functionalized carbon nanotubes. A DGEBA-DDS epoxy network was built using the ‘dendrimer’ growth approach where 75% of available epoxy sites were cross-linked. The epoxy model is verified through comparisons to experiments, and simulations are performed on nanotube reinforced cross-linked epoxy matrix using the CVFF force field in LAMMPS. Full stiffness matrices and linear coefficient of thermal expansion vectors are obtained for the nanocomposite. Large increases in stiffness and large decreases in thermal expansion were seen along the direction of the nanotube for both nanocomposite systems when compared to neat epoxy. The direction transverse to nanotube saw a 40% increase in stiffness due to covalent functionalization over neat epoxy at 1 K whereas the pristine nanotube system only saw a 7% increase due to van der Waals effects. The functionalized SWNT/epoxy nanocomposite showed an additional 42% decrease in thermal expansion along the nanotube direction when compared to the pristine SWNT/epoxy nanocomposite. The stiffness matrices are rotated over every possible orientation to simulate the effects of an isotropic system of randomly oriented nanotubes in the epoxy. The randomly oriented covalently functionalized SWNT/Epoxy nanocomposites showed substantial improvements over the plain epoxy in terms of higher stiffness (200% increase) and lower thermal expansion (32% reduction). Through MD simulations, we develop means to build simulation cells, perform annealing to reach correct densities, compute thermomechanical properties and compare with experiments.

  3. Atomistic modeling of thermomechanical properties of SWNT/Epoxy nanocomposites

    International Nuclear Information System (INIS)

    Fasanella, Nicholas; Sundararaghavan, Veera

    2015-01-01

    Molecular dynamics simulations are performed to compute thermomechanical properties of cured epoxy resins reinforced with pristine and covalently functionalized carbon nanotubes. A DGEBA-DDS epoxy network was built using the ‘dendrimer’ growth approach where 75% of available epoxy sites were cross-linked. The epoxy model is verified through comparisons to experiments, and simulations are performed on nanotube reinforced cross-linked epoxy matrix using the CVFF force field in LAMMPS. Full stiffness matrices and linear coefficient of thermal expansion vectors are obtained for the nanocomposite. Large increases in stiffness and large decreases in thermal expansion were seen along the direction of the nanotube for both nanocomposite systems when compared to neat epoxy. The direction transverse to nanotube saw a 40% increase in stiffness due to covalent functionalization over neat epoxy at 1 K whereas the pristine nanotube system only saw a 7% increase due to van der Waals effects. The functionalized SWNT/epoxy nanocomposite showed an additional 42% decrease in thermal expansion along the nanotube direction when compared to the pristine SWNT/epoxy nanocomposite. The stiffness matrices are rotated over every possible orientation to simulate the effects of an isotropic system of randomly oriented nanotubes in the epoxy. The randomly oriented covalently functionalized SWNT/Epoxy nanocomposites showed substantial improvements over the plain epoxy in terms of higher stiffness (200% increase) and lower thermal expansion (32% reduction). Through MD simulations, we develop means to build simulation cells, perform annealing to reach correct densities, compute thermomechanical properties and compare with experiments. (paper)

  4. Molecular environment of stable iodine and radioiodine (129I) in natural organic matter: Evidence inferred from NMR and binding experiments at environmentally relevant concentrations

    Science.gov (United States)

    Xu, Chen; Zhong, Junyan; Hatcher, Patrick G.; Zhang, Saijin; Li, Hsiu-Ping; Ho, Yi-Fang; Schwehr, Kathleen A.; Kaplan, Daniel I.; Roberts, Kimberly A.; Brinkmeyer, Robin; Yeager, Chris M.; Santschi, Peter H.

    2012-11-01

    129I is a major by-product of nuclear fission and had become one of the major radiation risk drivers at Department of Energy (DOE) sites. 129I is present at elevated levels in the surface soils of the Savannah River Site (SRS) F-Area and was found to be bound predominantly to soil organic matter (SOM). Naturally bound 127I and 129I to sequentially extracted humic acids (HAs), fulvic acids (FAs) and a water extractable colloid (WEC) were measured in a 129I-contaminated wetland surface soil located on the SRS. WEC is a predominantly colloidal organic fraction obtained from soil re-suspension experiments to mimic the fraction that may be released during groundwater exfiltration, storm water or surface runoff events. For the first time, NMR techniques were applied to infer the molecular environment of naturally occurring stable iodine and radioiodine binding to SOM. Iodine uptake partitioning coefficients (Kd) by these SOM samples at ambient iodine concentrations were also measured and related to quantitative structural analyses by 13C DPMAS NMR and solution state 1H NMR on the eight humic acid fractions. By assessing the molecular environment of iodine, it was found that it was closely associated with the aromatic regions containing esterified products of phenolic and formic acids or other aliphatic carboxylic acids, amide functionalities, quinone-like structures activated by electron-donating groups (e.g., NH2), or a hemicellulose-lignin-like complex with phenyl-glycosidic linkages. However, FAs and WEC contained much greater concentrations of 127I or 129I than HAs. The contrasting radioiodine contents among the three different types of SOM (HAs, FAs and WEC) suggest that the iodine binding environment cannot be explained solely by the difference in the amount of their reactive binding sites. Instead, indirect evidence indicates that the macro-molecular conformation, such as the hydrophobic aliphatic periphery hindering the active aromatic cores and the hydrophilic

  5. Tailored SWCNT functionalization optimized for compatibility with epoxy matrices

    International Nuclear Information System (INIS)

    Martinez-Rubi, Y; Kingston, C T; Daroszewska, M; Barnes, M; Simard, B; Gonzalez-Dominguez, J M; Ansón-Casaos, A; Martinez, M T; Hubert, P; Cattin, C

    2012-01-01

    We have modified single walled carbon nanotubes (SWCNTs) with well defined matrix-based architectures to improve interface interaction in SWCNT/epoxy composites. The hardener and two pre-synthesized oligomers containing epoxy and hardener moieties were covalently attached to the SWCNT walls by in situ diazonium or carboxylic coupling reactions. In this way, SWCNTs bearing amine or epoxide-terminated fragments of different molecular weights, which resemble the chemical structure of the cured resin, were synthesized. A combination of characterization techniques such as Raman and infrared absorption (FTIR) spectroscopy, elemental analysis and coupled thermogravimetry-FTIR spectroscopy were used to identify both the functional groups and degree of functionalization of SWCNTs synthesized by the laser ablation and arc-discharge methods. Depending on the type of reaction employed for the chemical functionalization and the molecular weight of the attached fragment, it was possible to control the degree of functionalization and the electronic properties of the functionalized SWCNTs. Improved dispersion of SWCNTs in the epoxy matrix was achieved by direct integration without using solvents, as observed from optical microscopy and rheology measurements of the SWCNT/epoxy mixtures. Composite materials using these fillers are expected to exhibit improved properties while preserving the thermosetting architecture. (paper)

  6. Development of a coupled diffusion denuder system combined with gas chromatography/mass spectrometry for the separation and quantification of molecular iodine and the activated iodine compounds iodine monochloride and hypoiodous acid in the marine atmosphere.

    Science.gov (United States)

    Huang, Ru-Jin; Hoffmann, Thorsten

    2009-03-01

    This study concerns the development of a coupled diffusion denuder system capable of separating and quantifying gaseous molecular iodine (I(2)) and two other highly reactive iodine species, ICl and HOI, which are collectively named activated iodine compounds (AIC). Both I(2) and AIC are key species in the atmospheric chemistry of iodine. 1,3,5-Trimethoxybenzene (1,3,5-TMB)- and alpha-cyclodextrin/(129)I(-) (alpha-CD/(129)I(-))-coated denuders proved to be suitable for the collection of gaseous AIC and I(2), respectively. The experimental collection efficiencies for AIC (tested as ICl) and I(2) agreed well with the theoretical values for gas flow rates in the range between 300 and 1800 mL min(-1). The coupled denuder system (1,3,5-TMB-coated denuder as front-denuder coupled upstream of an alpha-CD/(129)I(-)-coated denuder) was applied successfully to separate test gas mixtures of ICl and I(2) at various mixing ratios in the laboratory. The operation of both denuder systems was demonstrated to be independent of relative humidity (0-100%) and storage period (at least 2 weeks prior to and after sampling). Detection limits were achieved at sub-parts-per-trillion-by-volume (sub-pptv) level. The presented method provides a reliable and practical approach for the speciation of gaseous iodine compounds. In addition, we report for the first time ambient air measurements of AIC mixing ratios, carried out at the atmospheric research station in Mace Head, Ireland. A maximum concentration of AIC of 30.2 pptv was observed for nighttime measurements and 6.0 pptv for daytime measurements. A similar diurnal pattern was found for I(2) with an average concentration level of 23.2 pptv during daytime and 85.1 pptv during nighttime, indicating a strong correlation with AIC.

  7. CaI and SrI molecules for iodine determination by high-resolution continuum source graphite furnace molecular absorption spectrometry: Greener molecules for practical application.

    Science.gov (United States)

    Zanatta, Melina Borges Teixeira; Nakadi, Flávio Venâncio; da Veiga, Márcia Andreia Mesquita Silva

    2018-03-01

    A new method to determine iodine in drug samples by high-resolution continuum source graphite furnace molecular absorption spectrometry (HR-CS GF MAS) has been developed. The method measures the molecular absorption of a diatomic molecule, CaI or SrI (less toxic molecule-forming reagents), at 638.904 or 677.692nm, respectively, and uses a mixture containing 5μg of Pd and 0.5μg of Mg as chemical modifier. The method employs pyrolysis temperatures of 1000 and 800°C and vaporization temperatures of 2300 and 2400°C for CaI and SrI, respectively. The optimized amounts of Ca and Sr as molecule-forming reagents are 100 and 150µg, respectively. On the basis of interference studies, even small chlorine concentrations reduce CaI and SrI absorbance significantly. The developed method was used to analyze different commercial drug samples, namely thyroid hormone pills with three different iodine amounts (15.88, 31.77, and 47.66µg) and one liquid drug with 1% m v -1 active iodine in their compositions. The results agreed with the values informed by the manufacturers (95% confidence level) regardless of whether CaI or SrI was determined. Therefore, the developed method is useful for iodine determination on the basis of CaI or SrI molecular absorption. Copyright © 2017 Elsevier B.V. All rights reserved.

  8. Comparison of Molecular Iodine Spectral Properties at 514.7 and 532 nm Wavelengths

    Czech Academy of Sciences Publication Activity Database

    Hrabina, Jan; Acef, O.; Du Burck, F.; Chiodo, N.; Candela, Y.; Šarbort, Martin; Holá, Miroslava; Lazar, Josef

    2014-01-01

    Roč. 14, č. 4 (2014), s. 213-218 ISSN 1335-8871 R&D Projects: GA ČR GPP102/11/P820; GA MŠk(CZ) LO1212; GA MŠk ED0017/01/01; GA MŠk EE2.4.31.0016; GA TA ČR TA02010711; GA TA ČR TA01010995; GA TA ČR TE01020233 Institutional support: RVO:68081731 Keywords : laser spectroscopy * metrology * molecular iodine * absorption cells * frequency doubling * nterferometry Subject RIV: BH - Optics, Masers, Lasers Impact factor: 0.989, year: 2014

  9. Electron beam hardened paint binder

    International Nuclear Information System (INIS)

    Johnson, O.B.; Labana, S.S.

    1976-01-01

    The invention concerns a paint binder hardened by the effect of electron beams (0.1-100 Mrad/sec). It consists of a dispersion of (A) an ethylenic unsaturated material in (B) at least one vinyl monomer. The component (A) in a reaction product of degraded rubber particles (0.1-4 μm) and an ethylenic unsaturated component with a reactive epoxy, hydroxy or carboxy group which is bonded to the rubber particles by ester or urethane compounds. The rubber particles possess a nucleus and a cross-linked elastomeric acryl polymer, an outer shell with reactive groups and an intermediate layer formed by the monomers of the nucleus and the shell. The manner of production is described in great detail and supplemented by 157 examples. The coatings are suitable to coat articles which will be subject to deformation. (UWI) [de

  10. Identification and imaging of modern paints using Secondary Ion Mass Spectrometry with MeV ions

    DEFF Research Database (Denmark)

    Bogdanović Radović, Iva; Siketić, Zdravko; Jembrih-Simbürger, Dubravka

    2017-01-01

    Secondary Ion Mass Spectrometry using MeV ion excitation was applied to analyse modern paint materials containing synthetic organic pigments and binders. It was demonstrated that synthetic organic pigments and binder components with molecular masses in the m/z range from 1 to 1200 could be identi......Secondary Ion Mass Spectrometry using MeV ion excitation was applied to analyse modern paint materials containing synthetic organic pigments and binders. It was demonstrated that synthetic organic pigments and binder components with molecular masses in the m/z range from 1 to 1200 could...... be identified in different paint samples with a high efficiency and in a single measurement. Different ways of mounting of mostly insulating paint samples were tested prior to the analysis in order to achieve the highest possible yield of pigment main molecular ions. As Time-of-Flight mass spectrometer for Me......V Secondary Ion Mass Spectrometry is attached to the heavy ion microprobe, molecular imaging on cross-sections of small paint fragments was performed using focused ions. Due to the fact that molecules are extracted from the uppermost layer of the sample and to avoid surface contamination, the paint samples...

  11. Functionalizing CNTs for Making Epoxy/CNT Composites

    Science.gov (United States)

    Chen, Jian; Rajagopal, Ramasubramaniam

    2009-01-01

    Functionalization of carbon nanotubes (CNTs) with linear molecular side chains of polyphenylene ether (PPE) has been shown to be effective in solubilizing the CNTs in the solvent components of solutions that are cast to make epoxy/CNT composite films. (In the absence of solubilization, the CNTs tend to clump together instead of becoming dispersed in solution as needed to impart, to the films, the desired CNT properties of electrical conductivity and mechanical strength.) Because the PPE functionalizes the CNTs in a noncovalent manner, the functionalization does not damage the CNTs. The functionalization can also be exploited to improve the interactions between CNTs and epoxy matrices to enhance the properties of the resulting composite films. In addition to the CNTs, solvent, epoxy resin, epoxy hardener, and PPE, a properly formulated solution also includes a small amount of polycarbonate, which serves to fill voids that, if allowed to remain, would degrade the performance of the film. To form the film, the solution is drop-cast or spin-cast, then the solvent is allowed to evaporate.

  12. Effect of Interfacial Bonding on Interphase Properties in SiO2/Epoxy Nanocomposite: A Molecular Dynamics Simulation Study.

    Science.gov (United States)

    Wang, Zhikun; Lv, Qiang; Chen, Shenghui; Li, Chunling; Sun, Shuangqing; Hu, Songqing

    2016-03-23

    Atomistic molecular dynamics simulations have been performed to explore the effect of interfacial bonding on the interphase properties of a nanocomposite system that consists of a silica nanoparticle and the highly cross-linked epoxy matrix. For the structural properties, results show that interfacial covalent bonding can broaden the interphase region by increasing the radial effect range of fluctuated mass density and oriented chains, as well as strengthen the interphase region by improving the thermal stability of interfacial van der Waals excluded volume and reducing the proportion of cis conformers of epoxy segments. The improved thermal stability of the interphase region in the covalently bonded model results in an increase of ∼21 K in the glass transition temperature (Tg) compared to that of the pure epoxy. It is also found that interfacial covalent bonding mainly restricts the volume thermal expansion of the model at temperatures near or larger than Tg. Furthermore, investigations from mean-square displacement and fraction of immobile atoms point out that interfacial covalent and noncovalent bonding induces lower and higher mobility of interphase atoms than that of the pure epoxy, respectively. The obtained critical interfacial bonding ratio when the interphase and matrix atoms have the same mobility is 5.8%. These results demonstrate that the glass transitions of the interphase and matrix will be asynchronous when the interfacial bonding ratio is not 5.8%. Specifically, the interphase region will trigger the glass transition of the matrix when the ratio is larger than 5.8%, whereas it restrains the glass transition of the matrix when the ratio is smaller than 5.8%.

  13. Epoxy cracking in the epoxy-impregnated superconducting winding: nonuniform dissipation of stress energy in a wire-epoxy matrix model

    International Nuclear Information System (INIS)

    Tsukamoto, O.; Iwasa, Y.

    1985-01-01

    The authors present the epoxy-crack-induced temperature data of copper wires imbedded in wire-epoxy resin composite model at 4.2 K. The experimental results show that the epoxy-crackinduced temperature rise is higher in the copper wires than in the epoxy matrix, indicating that in stress-induced wire-epoxy failure, stress energy stored in the wire-epoxy matrix is preferrentially dissipated in the wire. A plausible mechanism of the nonuniform dissipation is presented

  14. Identification and imaging of modern paints using Secondary Ion Mass Spectrometry with MeV ions

    Science.gov (United States)

    Bogdanović Radović, Iva; Siketić, Zdravko; Jembrih-Simbürger, Dubravka; Marković, Nikola; Anghelone, Marta; Stoytschew, Valentin; Jakšić, Milko

    2017-09-01

    Secondary Ion Mass Spectrometry using MeV ion excitation was applied to analyse modern paint materials containing synthetic organic pigments and binders. It was demonstrated that synthetic organic pigments and binder components with molecular masses in the m/z range from 1 to 1200 could be identified in different paint samples with a high efficiency and in a single measurement. Different ways of mounting of mostly insulating paint samples were tested prior to the analysis in order to achieve the highest possible yield of pigment main molecular ions. As Time-of-Flight mass spectrometer for MeV Secondary Ion Mass Spectrometry is attached to the heavy ion microprobe, molecular imaging on cross-sections of small paint fragments was performed using focused ions. Due to the fact that molecules are extracted from the uppermost layer of the sample and to avoid surface contamination, the paint samples were not embedded in the resin as is usually done when imaging of paint samples using different techniques in the field of cultural heritage.

  15. Anti-microbial and skin wound dressing application of molecular iodine nanoparticles

    Science.gov (United States)

    Viswanathan, Kaliyaperumal; Bharathi Babu, Divya; Jayakumar, Gomathi; Dhinakar Raj, Gopal

    2017-10-01

    In this study, iodine nanoparticles were synthesized without use of any stabilizer by a new co-precipitation process using polyvinyl pyrolidone, calcium lactate, disodium hydrogen phosphate and iodine solution as precursor and the reaction was catalyzed by sodium hydroxide. Ten mg of the synthesized nanoparticles killed 95% of bacteria and inhibited 90% of bio film formation. Assays on membrane disintegration activities of the nanoparticles indicated that these nanoparticles destroyed the extracellular membrane of the bacteria. The wound healing application evaluated using mice model showed that it was hastened by iodine nanoparticles.

  16. In situ detection of atomic and molecular iodine using Resonance and Off-Resonance Fluorescence by Lamp Excitation: ROFLEX

    Directory of Open Access Journals (Sweden)

    J. C. Gómez Martín

    2011-01-01

    Full Text Available We demonstrate a new instrument for in situ detection of atmospheric iodine atoms and molecules based on atomic and molecular resonance and off-resonance ultraviolet fluorescence excited by lamp emission. The instrument combines the robustness, light weight, low power consumption and efficient excitation of radio-frequency discharge light sources with the high sensitivity of the photon counting technique. Calibration of I2 fluorescence is achieved via quantitative detection of the molecule by Incoherent Broad Band Cavity-enhanced Absorption Spectroscopy. Atomic iodine fluorescence signal is calibrated by controlled broad band photolysis of known I2 concentrations in the visible spectral range at atmospheric pressure. The instrument has been optimised in laboratory experiments to reach detection limits of 1.2 pptv for I atoms and 13 pptv for I2, for S/N = 1 and 10 min of integration time. The ROFLEX system has been deployed in a field campaign in northern Spain, representing the first concurrent observation of ambient mixing ratios of iodine atoms and molecules in the 1–350 pptv range.

  17. Solar-simulator-pumped atomic iodine laser kinetics

    Science.gov (United States)

    Wilson, H. W.; Raju, S.; Shiu, Y. J.

    1983-01-01

    The literature contains broad ranges of disagreement in kinetic data for the atomic iodine laser. A kinetic model of a solar-simulator-pumped iodine laser is used to select those kinetic data consistent with recent laser experiments at the Langley Research Center. Analysis of the solar-simulator-pumped laser experiments resulted in the following estimates of rate coefficients: for alkyl radical (n-C3F7) and atomic iodine (I) recombination, 4.3 x 10 to the 11th power (1.9) + or - cu cm/s; for n-C3F7I stabilized atomic iodine recombination (I + I) 3.7 x 10 to the -32nd power (2.3) + or -1 cm to the 6th power/s; and for molecular iodine (I2) quenching, 3.1 x 10 to the -11th power (1.6) + or - 1 cu cm/s. These rates are consistent with the recent measurements.

  18. Landscape Painting. Rewriting Painting in the Postmedium Condition

    Directory of Open Access Journals (Sweden)

    Gal, Nissim

    2011-02-01

    Full Text Available Is landscape painting still relevant today? To answer this question the article examines the work of the contemporary artist Yehudit Sasportas. Sasporas offers a unique kind of written-drawn landscape painting that moves between the manual and the mechanical. The theoretical perspectives from which it is approached are taken, among others, from Plato, Heidegger and Derrida on the issue of writing. Sasportas painting, which may be characterized as "painting under erasure" or "Landscape Painting", serves as a key to understanding the status of painting as a relevant medium, not because it defines medium according to the modernist Greenbergian formula, but because it enables an understanding of painting as a field that exists in a variety of media. Painting as a field, in Sasportas's art, works and lives within various techniques and materials, even when it includes within itself a melancholic mark indicating doubt about its own relevance.

  19. Development of microwave absorbing materials prepared from a polymer binder including Japanese lacquer and epoxy resin

    Science.gov (United States)

    Iwamaru, T.; Katsumata, H.; Uekusa, S.; Ooyagi, H.; Ishimura, T.; Miyakoshi, T.

    Microwave absorption composites were synthesized from a poly urushiol epoxy resin (PUE) mixed with one of microwave absorbing materials; Ni-Zn ferrite, Soot, Black lead, and carbon nano tube (CNT) to investigate their microwave absorption properties. PUE binders were specially made from Japanese lacquer and epoxy resin, where Japanese lacquer has been traditionally used for bond and paint because it has excellent beauty. Japanese lacquer solidifies with oxygen contained in air's moisture, which has difficulty in making composite, but we improved Japanese lacquer's solidification properties by use of epoxy resin. We made 10 mm thickness composite samples and cut them into toroidal shape to measure permittivity, permeability, and reflection loss in frequencies ranging from 50 Hz to 20 GHz. Electric magnetic absorber's composites synthesized from a PUE binders mixed either with Soot or CNT showed significantly higher wave absorption over -27 dB than the others at frequencies around 18 GHz, although Japanese lacquer itself doesn't affect absorption. This means Japanese lacquer can be used as binder materials for microwave absorbers.

  20. Phebus FPT-O. Exploratory containment iodine chemistry calculations

    International Nuclear Information System (INIS)

    Fermandjian, J.; Dickinson, S.; Edward, J.B.; Ewig, F.J.; Funke, F.; Hueber, C.; Rodriguez-Maroto, J.J.; Sims, H.E.

    1994-01-01

    The results of the exploratory containment iodine chemistry calculations related to the first Phebus-FP test (benchmark exercise for explaining the reasons for code inconsistencies and realistic calculation for test preparation) are reported. Calculations have been performed by CEA/IPSN/DRS/SEMAR-Cadarache (France), CIEMAT-Madrid (Spain), GRS-Koeln and SIEMENS/KWU, Erlangen (Germany), AEA-Harwell (UK), Ontario Hydro-Toronto, University of Toronto and AECL-Whiteshell (Canada). The code benchmark results show that mechanistic codes (INSPECT and LIRIC) are in agreement for molecular iodine concentration in the gaseous phase, whereas empirical codes (IODE and IMPAIR) are in disagreement because they model differently HOI disproportionation and use different radiolytic constant values (iodide/iodate radiolysis). Furthermore, the molecular iodine concentrations in the gaseous phase are 10 to 100 times higher at acid pH (pH - 5) than at neutral pH (pH - 7), and the presence of organic radicals in water does not change the concentrations of inorganic iodine species. Concerning the realistic calculation, the iodine mass distribution in the containment differ from one code to another, but all codes predict that the iodine concentration in the gaseous phase is high enough to be detected by foreseen instrumentation (as was verified during the test). FPT-0 test has been performed in December 1993. Analysis of experimental results is underway and result interpretation will be available at the beginning of 1995. (author). 11 refs., 1 tab., 5 figs

  1. EFFECT OF MOLECULAR WEIGHT ON THE YIELD BEHAVIOUR OF EPY EPOXY COMPOUND

    Directory of Open Access Journals (Sweden)

    Magdalena Urbaniak

    2016-12-01

    Full Text Available A series of epoxy networks with molecular weight between crosslinks (Mc ranging from 117 to 508 g/mol were investigated by employing as DSC and DMA methods and compression testing over a broad range of test temperatures (from 20 to 120 °C and strain rates (from 0.0208 to 20.8 min–1. Mechanical characteristics vs. testing temperature and strain rate developed in relation to working conditions of EPY compound applied for machine foundation chocks as well as effect of crosslinking on glass transition temperature (Tg presented in this paper let to find out the effect of molecular architecture composed chiefly by Mc on the thermal and mechanical properties that govern yield behaviour of the material. The investigations carried out in a.m. ranges of testing temperatures and strain rates showed that whichever change of Mc is related to the change in crosslink density causing relative shift in the Tg of the compound. However, a sensitivity of the polymer material on changes in strain rate falls down with growth of testing temperature. Obtained results prove that yielding in EPY compound can be examined in categories of the Eyring’s plastic flow model in which yielding is described.

  2. Electrical infrared in the baking of paints and the drying of coatings; L`infrarouge electrique dans la cuisson des peintures et le sechage des revetements

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This conference day was organized by the `industrial electro-thermal engineering` section of the French association of thermal engineers. This book of proceedings contains 11 papers entitled: `recalls about infrared emitters and furnaces technology`; `experimental study of transfer phenomena and of the thermophysical properties of paints during baking under infrared radiation`; `synthetic report of a theoretical and experimental study about drying and reticulation under infrared radiation of a aqueous-based epoxy-amine-type paint on metal support`; `short IR baking as viewed by the paint manufacturer`; `influence of texture and impurities on the radiative properties of materials`; `contribution of modeling to the dimensioning of IR furnaces`; `IR baking of paints`; `experimental studies and testing means of EdF`; `presentation of ABB Capponi Alesina company`; `presentation report of the Infrarouge System company`; `the choice of heat transfer technologies`. (J.S.)

  3. Self-healing woven glass fabric/epoxy composites with the healant consisting of micro-encapsulated epoxy and latent curing agent

    International Nuclear Information System (INIS)

    Yin Tao; Zhou Lin; Rong Minzhi; Zhang Mingqiu

    2008-01-01

    This paper reports a study of self-healing woven glass fabric reinforced epoxy composites. The healing agent was a two-component one synthesized in the authors' laboratory, which consisted of epoxy-loaded urea-formaldehyde microcapsules as the polymerizable binder and CuBr 2 (2-methylimidazole) 4 (CuBr 2 (2-MeIm) 4 ) as the latent hardener. Both the microcapsules and the matching catalyst were pre-embedded and pre-dissolved in the composites' matrix, respectively. When the microcapsules are split by propagating cracks, the uncured epoxy can be released into the damaged areas and then consolidated under the catalysis of CuBr 2 (2-MeIm) 4 that was homogeneously distributed in the composites' matrix on a molecular scale. As a result, the cracked faces can be bonded together. The influence of the content of the self-healing agent on the composites' tensile properties, interlaminar fracture toughness and healing efficiency was evaluated. It was found that a healing efficiency over 70% relative to the fracture toughness of virgin composites was obtained in the case of 30 wt% epoxy-loaded microcapsules and 2 wt% latent hardener

  4. Iodine behaviour under LWR accident conditions: Lessons learnt from analyses of the first two Phebus FP tests

    International Nuclear Information System (INIS)

    Girault, N.; Dickinson, S.; Funke, F.; Auvinen, A.; Herranz, L.; Krausmann, E.

    2006-01-01

    The International Phebus Fission Product programme, initiated in 1988 and performed by the French 'Institut de Radioprotection et de Surete Nucleaire' (IRSN), investigates through a series of in-pile integral experiments, key phenomena involved in light water reactor (LWR) severe accidents. The tests cover fuel rod degradation and the behaviour of fission products released via the primary coolant circuit into the containment building. The results of the first two tests, called FPT0 and Ftp, carried out under low pressure, in a steam rich atmosphere and using fresh fuel for Ftp and fuel burned in a reactor at 23 GWdt -1 for Ftp, were immensely challenging, especially with regard to the iodine radiochemistry. Some of the most important observed phenomena with regard to the chemistry of iodine were indeed neither predicted nor pre-calculated, which clearly shows the interest and the need for carrying out integral experiments to study the complex phenomena governing fission product behaviour in a PWR in accident conditions. The three most unexpected results in the iodine behaviour related to early detection during fuel degradation of a weak but significant fraction of volatile iodine in the containment, the key role played by silver rapidly binding iodine to form insoluble AgI in the containment sump and the importance of painted surfaces in the containment atmosphere for the formation of a large quantity of volatile organic iodides. To support the Phebus test interpretation small-scale analytical experiments and computer code analyses were carried out. The former, helping towards a better understanding of overall iodine behaviour, were used to develop or improve models while the latter mainly aimed at identifying relevant key phenomena and at modelling weaknesses. Specific efforts were devoted to exploring the potential origins of the early-detected volatile iodine in the containment building. If a clear explanation has not yet been found, the non-equilibrium chemical

  5. Room temperature thin foil SLIM-cut using an epoxy paste: experimental versus theoretical results

    International Nuclear Information System (INIS)

    Bellanger, Pierre; Serra, Joao; Bouchard, Pierre-Olivier; Bernacki, Marc

    2015-01-01

    The stress induced lift-off method (SLIM) -cut technique allows the detachment of thin silicon foils using a stress inducing layer. In this work, results of SLIM-cut foils obtained using an epoxy stress inducing layer at room temperature are presented. Numerical analyses were performed in order to study and ascertain the important experimental parameters. The experimental and simulation results are in good agreement. Indeed, large area (5 × 5 cm 2 ) foils were successfully detached at room temperature using an epoxy thickness of 900 μm and a curing temperature of 150 °C. Moreover, three foils (5 × 3 cm 2 ) with thickness 135, 121 and 110 μm were detached from the same monocrystalline substrate. Effective minority carrier lifetimes of 46, 25 and 20 μs were measured using quasi-steady-state photoconductance technique in these foils after iodine ethanol surface passivation. (paper)

  6. Creep behavior of an epoxy resin and an epoxy-based FRP in condition of simultaneous supply of radiation and stress at cryogenic temperatures

    International Nuclear Information System (INIS)

    Nishiura, Tetsuya; Nishijima, Shigehiro; Okada, Toichi

    1995-01-01

    Creep tests of an epoxy resin and an epoxy-based FRP in bending under irradiation condition have been carried out, to investigate the synergistic effects of radiation and stress on mechanical properties of FRP. Simultaneous supply of stress and irradiation on the epoxy resin and the FRP enhanced creep rates in comparison with that supply of the stress on a post-irradiated one did. ESR spectra measurement was also carried out to study the change of molecule of the resin irradiated. Increase of molecular weight between crosslinks was found out to be enhanced by the synergistic effect of radiation and stress. The mechanism of increased damage of FRP induced by the effects of simultaneous stress and irradiation is discussed. (author)

  7. Processing and properties of carbon nanofibers reinforced epoxy powder composites

    International Nuclear Information System (INIS)

    Palencia, C.; Mazo, M. A.; Nistal, A.; Rubio, F.; Rubio, J.; Oteo, J. L.

    2011-01-01

    Commercially available CNFs (diameter 30–300 nm) have been used to develop both bulk and coating epoxy nanocomposites by using a solvent-free epoxy matrix powder. Processing of both types of materials has been carried out by a double-step process consisting in an initial physical premix of all components followed by three consecutive extrusions. The extruded pellets were grinded into powder and sieved. Carbon nanofibers powder coatings were obtained by electrostatic painting of the extruded powder followed by a curing process based in a thermal treatment at 200 °C for 25 min. On the other hand, for obtaining bulk carbon nanofibers epoxy composites, a thermal curing process involving several steps was needed. Gloss and mechanical properties of both nanocomposite coatings and bulk nanocomposites were improved as a result of the processing process. FE-SEM fracture surface microphotographs corroborate these results. It has been assessed the key role played by the dispersion of CNFs in the matrix, and the highly important step that is the processing and curing of the nanocomposites. A processing stage consisted in three consecutive extrusions has reached to nanocomposites free of entanglements neither agglomerates. This process leads to nanocomposite coatings of enhanced properties, as it has been evidenced through gloss and mechanical properties. A dispersion limit of 1% has been determined for the studied system in which a given dispersion has been achieved, as the bending mechanical properties have been increased around 25% compared with the pristine epoxy resin. It has been also demonstrated the importance of the thickness in the nanocomposite, as it involves the curing stage. The complex curing treatment carried out in the case of bulk nanocomposites has reached to reagglomeration of CNFs.

  8. Processing and properties of carbon nanofibers reinforced epoxy powder composites

    Science.gov (United States)

    Palencia, C.; Mazo, M. A.; Nistal, A.; Rubio, F.; Rubio, J.; Oteo, J. L.

    2011-11-01

    Commercially available CNFs (diameter 30-300 nm) have been used to develop both bulk and coating epoxy nanocomposites by using a solvent-free epoxy matrix powder. Processing of both types of materials has been carried out by a double-step process consisting in an initial physical premix of all components followed by three consecutive extrusions. The extruded pellets were grinded into powder and sieved. Carbon nanofibers powder coatings were obtained by electrostatic painting of the extruded powder followed by a curing process based in a thermal treatment at 200 °C for 25 min. On the other hand, for obtaining bulk carbon nanofibers epoxy composites, a thermal curing process involving several steps was needed. Gloss and mechanical properties of both nanocomposite coatings and bulk nanocomposites were improved as a result of the processing process. FE-SEM fracture surface microphotographs corroborate these results. It has been assessed the key role played by the dispersion of CNFs in the matrix, and the highly important step that is the processing and curing of the nanocomposites. A processing stage consisted in three consecutive extrusions has reached to nanocomposites free of entanglements neither agglomerates. This process leads to nanocomposite coatings of enhanced properties, as it has been evidenced through gloss and mechanical properties. A dispersion limit of 1% has been determined for the studied system in which a given dispersion has been achieved, as the bending mechanical properties have been increased around 25% compared with the pristine epoxy resin. It has been also demonstrated the importance of the thickness in the nanocomposite, as it involves the curing stage. The complex curing treatment carried out in the case of bulk nanocomposites has reached to reagglomeration of CNFs.

  9. Combination of ozone feed and wet electrostatic precipitator. Experimental study of an innovative system to filter gaseous iodine and iodine containing particles

    International Nuclear Information System (INIS)

    Gouëllo, Mélany; Hokkinen, Jouni; Kärkelä, Teemu; Auvinen, Ari

    2017-01-01

    Efficient mitigation systems capable of reducing as much as possible the radioactive discharge to the environment in a severe Nuclear Power Plant (NPP) accident are a necessity. Nuclear Power Plants are equipped with filtration systems which have been characterized for aerosol retention in a short term, but to a far lesser extent for the retention of volatile iodine or for the long-term behaviour of the system. After the Fukushima accident, one of the main concerns of the nuclear industry has been to verify the ability of filtration systems to mitigate the possible source term to the environment. Radiotoxic iodine has a significant contribution to a possible source term in a severe NPP accident. An innovative system has been developed at VTT Technical Research Centre of Finland Ltd. to filter gaseous iodine and iodine containing particles (e.g. I x O y ). The system consists of a combination of an ozone feed and a modern wet electrostatic precipitator (WESP). The electrostatic precipitation (ESP) technique is widely used in the industry to filter out impurities (i.e. particles) in gases. The advantage of a WESP is that the impurities are removed from the system with a solution. They can thus directly be transported to a water container, such as the sump in a nuclear power plant. The addition of ozone feed at the inlet of the WESP allows the oxidation of gaseous iodine into particles. The efficiency of the system for the filtration of gaseous molecular iodine and methyl iodine has been tested and the subsequent observations are further discussed in this paper. The results showed that the combination of WESP together with ozone feed results in a good filtering efficiency against molecular iodine under air atmosphere and air/steam atmosphere. (author)

  10. Epoxy resins used to seal brachytherapy seed

    International Nuclear Information System (INIS)

    Ferreira, Natalia Carolina Camargos; Ferraz, Wilmar Barbosa; Reis, Sergio Carneiro dos; Santos, Ana Maria Matildes dos

    2013-01-01

    Prostate cancer treatment with brachytherapy is recommended for patients with cancer at an early stage. In this treatment, small radioactive seeds are implanted directly in the prostate gland. These seeds are composed at least of one radionuclide carrier and an X-ray marker enclosed within a metallic tube usually sealed by laser process. This process is expensive and, furthermore, it can provoke a partial volatilization of the radionuclide and change the isotropy in dose distribution around the seed. In this paper, we present a new sealing process using epoxy resin. Three kinds of resins were utilized and characterized by scanning electron microscopy (SEM), energy dispersive X ray (EDS) and by differential scanning calorimetry (DSC) after immersion in simulated body fluid (SBF) and in sodium iodine solution (NaI). The sealing process showed excellent potential to replace the sealing laser usually employed. (author)

  11. Performance of an iodine-fueled radio-frequency ion-thruster

    Science.gov (United States)

    Holste, Kristof; Gärtner, Waldemar; Zschätzsch, Daniel; Scharmann, Steffen; Köhler, Peter; Dietz, Patrick; Klar, Peter J.

    2018-01-01

    Two sets of performance data of the same radio-frequency ion-thruster (RIT) have been recorded using iodine and xenon, respectively, as propellant. To characterize the thruster's performance, we have recorded the radio-frequency DC-power, required for yielding preset values of the extracted ion-beam currents, as a function of mass flow. For that purpose, an iodine mass flow system had to be developed, calibrated, and integrated into a newly-built test facility for studying corrosive propellants. The performance mappings for iodine and xenon differ significantly despite comparable operation conditions. At low mass flows, iodine exhibits the better performance. The situation changes at higher mass flows where the performance of iodine is significantly poorer than that of xenon. The reason is very likely related to the molecular nature of iodine. Our results show that iodine as propellant is compatible with RIT technology. Furthermore, it is a viable alternative as propellant for dedicated space missions. In particular, when taking into account additional benefits such as possible storage as a solid and its low price the use of iodine as propellant in ion thrusters is competitive.

  12. Iodine Deficiency

    Science.gov (United States)

    ... Fax/Phone Home » Iodine Deficiency Leer en Español Iodine Deficiency Iodine is an element that is needed ... world’s population remains at risk for iodine deficiency. Iodine Deficiency FAQs WHAT IS THE THYROID GLAND? The ...

  13. Total iodine quantification in fluids and tissues from iodine- or iodide-supplemented rats by ion chromatography following microwave-assisted digestion.

    Science.gov (United States)

    Delgado, Guadalupe; Muñoz-Torres, Carolina; Orozco-Esquivel, Teresa; Anguiano, Brenda; Aceves, Carmen

    2015-03-01

    Iodine is a crucial component of thyroid hormones, and several reports have shown that iodine per se is implicated in the physiopathology of other organs. Innovative ion chromatography detection following a four-step temperature ramp microwave digestion in 25-50 mM nitric acid was developed to measure total iodine in biological fluids and tissue samples from female Sprague-Dawley rats supplemented with 0.05% molecular iodine (I2) or 0.05% potassium iodide (I(-)) in drinking water. The reported method allows the measurement of total iodine with a limit of quantification of 13.7 μg L(-1), recoveries of 96.3-100.3%, and intra- and inter-assay variations, of 3.5% and 7.4% respectively. Analysis of biological fluids showed that after 48 hours, iodine-supplemented animals exhibited significantly higher levels of total iodine in both serum and urine compared with those supplemented with iodide. The half-life of iodine in serum and urine measured over the first 48 h showed similar patterns for both the I2 (7.89 and 7.76 hours) and I(-) (8.27 and 8.90 hours) supplements. Differential uptake patterns were observed in tissues after 6 days of supplements, with I(-) preferentially retained by thyroid, lactating mammary gland, and milk, and a slightly but significantly higher capture of I2 in pituitary, ovary, and virgin mammary gland. We developed a rapid, selective, and accurate digestion method to process fluid and tissue samples that permits reproducible measurements of total iodine by ion chromatography; iodine or iodide supplement show a similar serum and urine half-life, but organ-specific uptake depends on the chemical form of the iodine supplement.

  14. Kinetics of an oxygen – iodine active medium with iodine atoms optically pumped on the {sup 2}P{sub 1/2} – {sup 2}P{sub 3/2} transition

    Energy Technology Data Exchange (ETDEWEB)

    Zagidullin, M V; Azyazov, V N [Samara Branch of the P.N. Lebedev Physical Institute, Russian Academy of Sciences, Samara (Russian Federation); Malyshev, M S [S.P. Korolev Samara State Aerospace University, Samara (Russian Federation)

    2015-08-31

    The kinetics of the processes occurring in an O{sub 2} – I{sub 2} – He – H{sub 2}O gas flow in which photodissociation of molecular iodine at a wavelength close to 500 nm and excitation of atomic iodine on the {sup 2}P{sub 1/2} – {sup 2}P{sub 3/2} transition by narrow-band radiation near 1315 nm are implemented successively has been analysed. It is shown that implementation of these processes allows one to form an oxygen – iodine medium with a high degree of dissociation of molecular iodine and a relative content of singlet oxygen O{sub 2}(a{sup 1}Δ) exceeding 10%. Having formed a supersonic gas flow with a temperature ∼100 K from this medium, one can reach a small-signal gain of about 10{sup -2} cm{sup -1} on the {sup 2}P{sub 1/2} – {sup 2}P{sub 3/2} transition in iodine atoms. The specific power per unit flow cross section in the oxygen – iodine laser with this active medium may reach ∼100 W cm{sup -2}. (active media)

  15. The effect of BaM/PANI composition with epoxy paint matrix on single and double layers coating with spray coating method for radar absorbing materials applications

    Science.gov (United States)

    Widyastuti, Fajarin, Rindang; Pratiwi, Vania Mitha; Kholid, Rifki Rachman; Habib, Abdulloh

    2018-04-01

    In this study, RAM composite has been succesfully synthesized by mixing BaM as magnetic materials and PANI as conductive materials. BaM and PANI materials were prepared separately by solid state method and polymerization method, respectively. To investigated the presence of BaM phase and magnetic property of the as prepared BaM, XRD pert PAN analytical and VSM 250 Dexing Magnet were employed. Inductance Capacitance Resistance technique was carried out to measure electrical conductivity of the synthesized PANI materials. In order to further characterized the structural features of BaM and PANI, SEM-EDX FEI 850 and FTIR characterizations were conducted. RAM composite was prepared by mixing BaM and PANI powders with ultrasonic cleaner. Afterwards, VNA (Vector Network Analyzer) characterization was carried out to determine reflection loss value of RAM by applying mixed RAM composite and epoxy paint on aluminum plate using spray gun. Microscopic characterization was employed to investigated the distribution of RAM particles on the substrate. It was found that reflection loss value as low as -27.153 dB was achieved when applied 15 wt% BaM/PANi composite at 100.6 µm thickness. In addition, the absorption of electromagnetic waves value increase as the addition of RAM composite composition increases.

  16. Introduction to Test Facility for Iodine Retention in Filtered Containment Venting System

    Energy Technology Data Exchange (ETDEWEB)

    Jung, Jaehoon; An, Sang Mo; Ha, Kwang Soon; Kim, Hwan Yeol [KAERI, Daejeon (Korea, Republic of)

    2015-05-15

    In many countries the implementation of FCVS's is under discussion to mitigate fission product release not only in the short-term but also in the long-term view. To verify the performance of FCVS, the large-scaled tests have been performed such as advanced containment experiments (ACE), the iodine and aerosol retention rate test facility (JAVA), etc. The elemental and organic iodides are the main gaseous iodine species in the containment atmosphere. For the iodine retention, experimental programs have confirmed the existence of gaseous organic iodine in some cases in higher concentrations than for gaseous molecular iodine (I{sub 2}). The Reaction of Methyl iodide (CH{sub 3}I) with surfaces and the removal by containment filters and scrubbers is less efficient in comparison to molecular iodine. In the recent years, an experimental and analytical work has been conducted at the Paul Scherrer Institute (PSI) to develop a process leading to a fast, comprehensive and reliable retention of volatile iodine species in aqueous solutions. New FCVS test facility to verify the performance of FCVS is designed and under construction. The iodine retention tests are planned with elemental iodine or with organic iodide loaded carrier gas consisting of pure non-condensable gas, pure steam and of typical mixtures of non-condensable gas/steam. This paper introduces the iodine generation and measurement system for the iodine retention test of FCVS. In severe accidents elemental and organic iodides are the main gaseous iodine species in the containment atmosphere. Release of the gaseous species in sufficient quantities from containment to environment generates a risk for public health. The filtered containment venting systems (FCVS) can considerably reduce the leakage of radioactive materials to the environment. New integral test facility is prepared to verify a performance of the FCVS. The test facility consists of a test vessel, thermal-hydraulic, and aerosol/iodine generation and

  17. ORGANIC/INORGANIC HYBRID EPOXY NANOCOMPOSITES BASED ON OCTA(AMINOPHENYL)SILSESQUIOXANE

    Institute of Scientific and Technical Information of China (English)

    Hai-bo Fan; Rong-jie Yang; Xiang-mei Li

    2013-01-01

    Octa(aminophenyl)silsesquioxane (OAPS) was used as the curing agent of diglycidyl ether of bisphenol-A (DGEBA) epoxy resin.A study on comparison of DGEBA/OAPS with DGEBA/4,4'-diaminodiphenyl sulfone (DDS) epoxy resins was achieved.Differential scanning calorimetry was used to investigate the curing reaction and its kinetics,and the glass transition of DGEBA/OAPS.Thermogravimetric analysis was used to investigate thermal decomposition of the two kinds of epoxy resins.The reactions between amino groups and epoxy groups were investigated using Fourier transform infrared spectroscopy.Scanning electron microscopy was used to observe morphology of the two epoxy resins.The results indicated that OAPS had very good compatibility with DGEBA in molecular level,and could form a transparent DGEBA/OAPS resin.The curing reaction of the DGEBA/OAPS prepolymer could occur under low temperatures compared with DGEBA/DDS.The DGEBA/OAPS resin didn't exhibit glass transition,but the DGEBA/DDS did,which meant that the large cage structure of OAPS limited the motion of chains between the cross-linking points.Measurements of the contact angle indicated that the DGEBA/OAPS showed larger angles with water than the DGEBA/DDS resin.Thermogravimetric analysis indicated that the incorporation of OAPS into epoxy system resulted in low mass loss rate and high char yield,but its initial decomposition temperature seemed to be lowered.

  18. Exhalation velocity of radon-222 of Dutch building materials and the influence of paint systems

    International Nuclear Information System (INIS)

    Dijk, W. van; Jong, P. de

    1989-02-01

    In order to achieve a better insight concerning the source terms of radon in the Dutch dwelling in the framework of the RENA-programme an investigation has been performed into the exhalation velocity of radon-222 from building materials. From this investigation it turned out that the ventilation factor does not have any influence upon the exhalation velocity, neither an influence of alteration of air pressure could be demonstrated. The influence of air humidity upon the exhalation velocity showed a twofold picture; for gypsum a linear increase of the exhalation velocity with vapour pressure was found, while for concrete a linear decrease with vapour pressure was observed. Further it has been investigated in how far paint systems diminish the exhalation velocity of the Rn-222 from gypsum and concrete. Acryl paints, mostly used in the Dutch dwelling, did not show a decrease of the exhalation velocity and structure paints did even cause an increase of the exhalation velocity. Other types of paint based on chlorous rubber, epoxy resins and poly-urethane, in contrast, showed a clear reduction. From these those based on poly-urethane showed the largest reduction (60-75%) at a double sided treatment of the wall. With the help of a mathematical modelling of the exhalation estimations have been made of the exhalation velocity of Rn-222 at single sided treatment of a wall and for the exhalation velocity of Rn-220. For the fore mentioned poly-urethane-paints this yelds, at an estimate, a reduction of respectively 90-95% and 100%. (author). 40 refs.; 15 figs.; 8 tabs

  19. Iodination of the humic samples from Hupa project

    International Nuclear Information System (INIS)

    Reiller, P.; Mercier-Bion, F.; Barre, N.; Gimenez, N.; Miserque, F.

    2005-01-01

    Full text of publication follows: Iodine radioactive isotopes, such as 129 I, are important radionuclides due to their significant impact in geological disposal: in the conditions of natural reducing groundwaters, iodine would essentially be present in the form of highly mobile iodide anion. But in shallow waters the presence of molecular iodine is to be taken into account. The interaction of iodine with natural organic matter in general and with humic substances (HS) in particular, has been the subject of numerous studies. It has been shown that in some cases, organically bound iodine can dominate the speciation either as methyl iodide or bound to humic substances [1, 2]. It is now also clear that this reactivity is closely related to the occurrence of molecular iodine I 2 (aq). The reaction scheme can be viewed as an electrophilic substitution of a hydrogen atom by an iodine atom on a phenolic ring. Nevertheless, in some of the latter studies, the characterization of the final reaction products did not satisfy the authors completely as total separation from I - produced during the iodination could not be achieved. Thus, further studies were led using samples from the CCE HUPA project: natural humic and fulvic extract from Gorleben [3] and synthetic samples obtained from FZ Rossendorf [4]. Dialysis procedures were envisaged to improve the incomplete separation between the colloidal humic matter and the iodide ions either unreacted or produced by the reaction [2]. The iodination of these samples were monitored using UV-Visible spectrophotometry. As in previous studies [2], the kinetics could not be linearized in simple order but the trends were conform to simple phenolic patterns. The apparent rates could nevertheless be correlated to the aromaticity (H/C ratio) of the samples. After dialysis, the iodine humic/fulvic interaction was characterised to occur as a carbon-iodine covalent bonding by X-ray photoelectron spectroscopy (XPS) [5]. Electro-spray ionisation

  20. The glass transition in cured epoxy thermosets: A comparative molecular dynamics study in coarse-grained and atomistic resolution

    International Nuclear Information System (INIS)

    Langeloth, Michael; Böhm, Michael C.; Müller-Plathe, Florian; Sugii, Taisuke

    2015-01-01

    We investigate the volumetric glass transition temperature T g in epoxy thermosets by means of molecular dynamics simulations. The epoxy thermosets consist of the resin bisphenol A diglycidyl ether and the hardener diethylenetriamine. A structure based coarse-grained (CG) force field has been derived using iterative Boltzmann inversion in order to facilitate simulations of larger length scales. We observe that T g increases clearly with the degree of cross-linking for all-atomistic (AA) and CG simulations. The transition T g in CG simulations of uncured mixtures is much lower than in AA-simulations due to the soft nature of the CG potentials, but increases all the more with the formation of rigid cross-links. Additional simulations of the CG mixtures in contact with a surface show the existence of an interphase region of about 3 nm thickness in which the network properties deviate significantly from the bulk. In accordance to experimental studies, we observe that T g is reduced in this interphase region and gradually increases to its bulk value with distance from the surface. The present study shows that the glass transition is a local phenomenon that depends on the network structure in the immediate environment

  1. Iodine behaviour in the SLOWPOKE nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Bekeris, P A; Evans, G J [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

    1994-12-31

    The purpose of this project is to measure and attempt to explain the presence and volatility of iodine isotopes present as fission products in the SLOWPOKE-2 reactor. Liquid sampling and extraction procedures developed indicated that approximately 40% of the reactor iodine is in the form of iodate (IO{sub 3}{sup -}), and 60% is in the form of iodide (I{sup -}). No appreciable amount in non-polar forms such as molecular iodine (I{sub 2}) or organic iodides (RI) were detected. This goes contrary to past expectations that all of the iodine in the liquid phase would be in the form of I{sup -}. In addition partition coefficients for I-131 were determined as 2-6x10{sup 6} at a neutral pH. Kr-88 is suspected as a possible interfering isotope in the measurement of I-131 in the liquid and gas phases. (author). 9 refs., 2 tabs., 2 figs.

  2. Iodine volatility

    International Nuclear Information System (INIS)

    Beahm, E.C.; Shockley, W.E.

    1984-01-01

    The ultimate aim of this program is to couple experimental aqueous iodine volatilities to a fission product release model. Iodine partition coefficients, for inorganic iodine, have been measured during hydrolysis and radiolysis. The hydrolysis experiments have illustrated the importance of reaction time on iodine volatility. However, radiolysis effects can override hydrolysis in determining iodine volatility. In addition, silver metal in radiolysis samples can react to form silver iodide accompanied by a decrease in iodine volatility. Experimental data are now being coupled to an iodine transport and release model that was developed in the Federal Republic of Germany

  3. Decontamination of paint-coated concrete in nuclear plants using laser technology

    Energy Technology Data Exchange (ETDEWEB)

    Anthofer, Anton; Lippmann, Wolfgang; Hurtado, Antonio [Technische Univ. Dresden (Germany). Chair of Hydrogen and Nuclear Technology

    2013-07-01

    A review of the state of the art shows the technical novelty of the combined project. The development of an all-in-one process for treatment hazard chemical contamination on concrete structures with online monitoring method reduces the laborious mechanic decontamination and post-treatment. For safe experimental investigations, a three-barrier-system was constructed and can be used for tests with - first - epoxy paint in order to analyze and optimize the process. Simulation models help to formulate a mathematic scheme of the decontamination process by laser technology. The goal is a decontamination system with an online analyzing system of the flue gas for a mobile and extensive component in nuclear and conventional decommission. (orig.)

  4. Iodine Tagging Velocimetry in a Mach 10 Wake

    Science.gov (United States)

    Balla, Robert Jeffrey

    2013-01-01

    A variation on molecular tagging velocimetry (MTV) [1] designated iodine tagging velocimetry (ITV) is demonstrated. Molecular iodine is tagged by two-photon absorption using an Argon Fluoride (ArF) excimer laser. A single camera measures fluid displacement using atomic iodine emission at 206 nm. Two examples ofMTVfor cold-flowmeasurements areN2OMTV [2] and Femtosecond Laser Electronic Excitation Tagging [3]. These, like most MTV methods, are designed for atmospheric pressure applications. Neither can be implemented at the low pressures (0.1- 1 Torr) in typical hypersonic wakes. Of all the single-laser/singlecamera MTV approaches, only Nitric-Oxide Planar Laser Induced Fluorescence-based MTV [4] has been successfully demonstrated in a Mach 10 wake. Oxygen quenching limits transit times to 500 ns and accuracy to typically 30%. The present note describes the photophysics of the ITV method. Off-body velocimetry along a line is demonstrated in the aerothermodynamically important and experimentally challenging region of a hypersonic low-pressure near-wake in a Mach 10 air wind tunnel. Transit times up to 10 µs are demonstrated with conservative errors of 10%.

  5. Radionuclide Basics: Iodine

    Science.gov (United States)

    ... Centers Radiation Protection Contact Us Share Radionuclide Basics: Iodine Iodine (chemical symbol I) is a chemical element. ... in the environment Iodine sources Iodine and health Iodine in the Environment All 37 isotopes of iodine ...

  6. Iodine excretion during stimulation with rhTSH in differentiated thyroid carcinoma

    International Nuclear Information System (INIS)

    Loeffler, M.; Weckesser, M.; Franzius, C.; Kies, P.; Schober, O.

    2003-01-01

    Aim: Elevated iodine intake is a serious problem in the diagnostic and therapeutic application of 131 iodine in patients with differentiated thyroid cancer. Therefore, iodine avoidance is necessary 3 months in advance. Additionally, endogenous stimulation requires withdrawal of thyroid hormone substitution for 4 weeks. Exogenous stimulation using recombinant human TSH (rhTSH) enables the continuous substitution of levothyroxine, which contains 65.4% of its molecular weight in iodine. Thus, a substantial source of iodine intake is maintained during exogenous stimulation. Although this amount of stable iodine is comparable to the iodine intake in regions of normal iodine supply, it may reduce the accumulation of radioiodine in thyroid carcinoma tissue. The aim of this study was to assess the iodine excretion depending on different ways of stimulation. Methods: Iodine excretion was measured in 146 patients in the long term follow up after differentiated thyroid carcinoma. Patients were separated into 2 groups, those on hormone withdrawal (G I) and rhTSH-stimulated patients on hormone substitution (G II). Results: Iodine excretion was significantly lower in hypothyroid patients (G I, median 50 μg/l, range: 25-600 μg/l) than in those under levothyroxine medication (G II, median 75 μg/l, 25-600 μg/l, p [de

  7. Multiscale Modeling of Carbon Nanotube-Epoxy Nanocomposites

    Science.gov (United States)

    Fasanella, Nicholas A.

    Epoxy-composites are widely used in the aerospace industry. In order to improve upon stiffness and thermal conductivity; carbon nanotube additives to epoxies are being explored. This dissertation presents multiscale modeling techniques to study the engineering properties of single walled carbon nanotube (SWNT)-epoxy nanocomposites, consisting of pristine and covalently functionalized systems. Using Molecular Dynamics (MD), thermomechanical properties were calculated for a representative polymer unit cell. Finite Element (FE) and orientation distribution function (ODF) based methods were used in a multiscale framework to obtain macroscale properties. An epoxy network was built using the dendrimer growth approach. The epoxy model was verified by matching the experimental glass transition temperature, density, and dilatation. MD, via the constant valence force field (CVFF), was used to explore the mechanical and dilatometric effects of adding pristine and functionalized SWNTs to epoxy. Full stiffness matrices and linear coefficient of thermal expansion vectors were obtained. The Green-Kubo method was used to investigate the thermal conductivity as a function of temperature for the various nanocomposites. Inefficient phonon transport at the ends of nanotubes is an important factor in the thermal conductivity of the nanocomposites, and for this reason discontinuous nanotubes were modeled in addition to long nanotubes. To obtain continuum-scale elastic properties from the MD data, multiscale modeling was considered to give better control over the volume fraction of nanotubes, and investigate the effects of nanotube alignment. Two methods were considered; an FE based method, and an ODF based method. The FE method probabilistically assigned elastic properties of elements from the MD lattice results based on the desired volume fraction and alignment of the nanotubes. For the ODF method, a distribution function was generated based on the desired amount of nanotube alignment

  8. Ultrasound-assisted synthesis of zinc molybdate nanocrystals and molybdate-doped epoxy/PDMS nanocomposite coatings for Mg alloy protection.

    Science.gov (United States)

    Eduok, Ubong; Szpunar, Jerzy

    2018-06-01

    Zinc molybdate (ZM) is a safer anticorrosive additive for cooling systems when compared with chromates and lead salts, due to its insolubility in aqueous media. For most molybdate pigments, their molybdate anion (MoO 4 -2 ) acts as an anionic inhibitor and its passivation capacity is comparable with chromate anion (CrO 4 -2 ). To alleviate the environmental concerns involving chromates-based industrial protective coatings, we have proposed new alternative in this work. We have synthesized ZM nanocrystals via ultrasound-assisted process and encapsulated them within an epoxy/PDMS coating towards corrosion protection. The surface morphology and mechanical properties of these ZM doped epoxy/PDMS nanocomposite coatings is exhaustively discussed to show the effect of ZM content on protective properties. The presence of ZM nanocrystals significantly contributed to the corrosion barrier performance of the coating while the amount of ZM nanocrystals needed to prepare an epoxy coating with optimum barrier performance was established. Beyond 2 wt% ZM concentration, the siloxane-structured epoxy coating network became saturated with ZM pigments. This further broadened inherent pores channels, leading to the percolation of corrosion chloride ions through the coating. SEM evidence has revealed proof of surface delamination on ZM3 coating. A model mechanism of corrosion resistance has been proposed for ZM doped epoxy/PDMS nanocomposite coatings from exhaustive surface morphological investigations and evidence. This coating matrix may have emerging applications in cooling systems as anticorrosive surface paints as well as create an avenue for environmental corrosion remediation. Copyright © 2018 Elsevier B.V. All rights reserved.

  9. 49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

  10. Evaporation of iodine from nitric acid with the aid of peroxide

    International Nuclear Information System (INIS)

    Cathers, G.I.; Shipman, C.J.

    1975-01-01

    Traces of radioactive iodine with a concentration of 5 x 10 -4 M or less that remained in nitric acid solution after reprocessing of nuclear fuels can, without great apparatus effort, be distilled off as hydrogen iodide by continuous addition of hydrogen peroxide to the solution boiling at about 105 0 C to 1,15 0 C, and then be separated as elementary iodine. Starting from a 4 to 6 molecular nitric acid solution, the H 2 O 2 -concentration amounts to 0.012 percentage by weight and is kept at this level during the entire distillation process. The iodine concentration is also profitably kept at the level of the starting solution by adding non-radioactive iodine, since an isotopec exchange of radioactive iodine bound in organic impurities is advanced in that way. (UWI) [de

  11. Is placental iodine content related to dietary iodine intake?

    LENUS (Irish Health Repository)

    Burns, R

    2011-08-01

    Delivery of iodine to the foetus depends not only on maternal dietary iodine intake but also on the presence of a functioning placental transport system. A role for the placenta as an iodine storage organ has been suggested, and this study compares the iodine content of placentas from women giving birth at term in Ireland and Iran, areas with median urinary iodine of 79 and 206 μg\\/l respectively.

  12. The Effect of High Concentration and Small Size of Nanodiamonds on the Strength of Interface and Fracture Properties in Epoxy Nanocomposite

    Directory of Open Access Journals (Sweden)

    Yasir A. Haleem

    2016-06-01

    Full Text Available The concentration and small size of nanodiamonds (NDs plays a crucial role in the mechanical performance of epoxy-based nanocomposites by modifying the interface strength. Herein, we systemically analyzed the relation between the high concentration and small size of ND and the fracture properties of its epoxy-based nanocomposites. It was observed that there is a two-fold increase in fracture toughness and a three-fold increase in fracture energy. Rationally, functionalized-NDs (F-NDs showed a much better performance for the nanocomposite than pristine NDs (P-NDs because of additional functional groups on its surface. The F-ND/epoxy nanocomposites exhibited rougher surface in contrast with the P-ND/epoxy, indicating the presence of a strong interface. We found that the interfaces in F-ND/epoxy nanocomposites at high concentrations of NDs overlap by making a web, which can efficiently hinder further crack propagation. In addition, the de-bonding in P-ND/epoxy nanocomposites occurred at the interface with the appearance of plastic voids or semi-naked particles, whereas the de-bonding for F-ND/epoxy nanocomposites happened within the epoxy molecular network instead of the interface. Because of the strong interface in F-ND/epoxy nanocomposites, at high concentrations the de-bonding within the epoxy molecular network may lead to subsequent cracks, parallel to the parent crack, via crack splitting which results in a fiber-like structure on the fracture surface. The plastic void growth, crack deflection and subsequent crack growth were correlated to higher values of fracture toughness and fracture energy in F-ND/epoxy nanocomposites.

  13. Carbon Nanotube-Epoxy Nanocomposites: Correlation and Integration of Dynamic Impedance, Dielectric, and Mechanical Analyses

    Directory of Open Access Journals (Sweden)

    O. Moudam

    2013-01-01

    Full Text Available This study focuses on the characterization of MWNT-epoxy composites for different MWNT concentrations of 0–7 wt% by correlating different dynamic analysis techniques, including DMA, impedance, and DEA. An optimum composition was established at 0.1 wt% MWNTs corresponding to the best MWNT dispersion which resulted in the formation of an optimum MWNT network. The addition of this low fraction of MWNTs in epoxy resulted in stiffening the molecular structure and suppressing certain molecular transitions, raising the dielectric constant especially in the low-to-medium frequency range, raising the electrical conductivity especially at the high frequencies, and increasing the electromagnetic shielding effectiveness. The 0.1% MWNT-epoxy nanocomposite switched the electromagnetic shielding behaviour from being a very effective absorber at low frequencies to being an effective reflector at high frequencies. Finally, the Nyquist plot derived from the dynamic impedance spectroscopy proved most useful at providing evidence of multiple size distribution of MWNT agglomerates.

  14. The glass transition in cured epoxy thermosets: A comparative molecular dynamics study in coarse-grained and atomistic resolution

    Energy Technology Data Exchange (ETDEWEB)

    Langeloth, Michael; Böhm, Michael C.; Müller-Plathe, Florian [Eduard-Zintl-Institut für Anorganische und Physikalische Chemie and Center of Smart Interfaces, Technische Universität Darmstadt, Alarich Weiss Straße 4, D-64287 Darmstadt (Germany); Sugii, Taisuke, E-mail: taisuke.sugii.zs@hitachi.com [Center for Technology Innovation – Mechanical Engineering, Research & Development Group, Hitachi, Ltd., 832-2, Horiguchi, Hitachinaka, Ibaraki 312-0034 (Japan)

    2015-12-28

    We investigate the volumetric glass transition temperature T{sub g} in epoxy thermosets by means of molecular dynamics simulations. The epoxy thermosets consist of the resin bisphenol A diglycidyl ether and the hardener diethylenetriamine. A structure based coarse-grained (CG) force field has been derived using iterative Boltzmann inversion in order to facilitate simulations of larger length scales. We observe that T{sub g} increases clearly with the degree of cross-linking for all-atomistic (AA) and CG simulations. The transition T{sub g} in CG simulations of uncured mixtures is much lower than in AA-simulations due to the soft nature of the CG potentials, but increases all the more with the formation of rigid cross-links. Additional simulations of the CG mixtures in contact with a surface show the existence of an interphase region of about 3 nm thickness in which the network properties deviate significantly from the bulk. In accordance to experimental studies, we observe that T{sub g} is reduced in this interphase region and gradually increases to its bulk value with distance from the surface. The present study shows that the glass transition is a local phenomenon that depends on the network structure in the immediate environment.

  15. Role of iodine in pathogenesis of thyroid disease - is induction of apoptosis consequence of iodine cytotoxicity?

    Directory of Open Access Journals (Sweden)

    Marković Ljiljana

    2017-01-01

    Full Text Available Iodine is one of the best-characterized environmental factors associated with autoimmune thyroid disease (ATD. Epidemiological studies have shown that ATD incidence has increased following the introduction of salt iodination in the 1920s; in addition, ATD patients can improve upon iodine restriction. In animal models such as BioBreeding/Worcester and Buffalo rats, obese chicken strain, and non-obese diabetic H-2h4 mice, excess iodine is associated with autoimmunity. Analyses of Hashimoto thyroiditis (HT have shown enlarged number of apoptotic follicular cells, and the destruction is an effect of death receptormediated apoptosis. Excess of iodine induces rapid apoptosis of goitrogen Wistar pretreated rats, possibly connected with inhibition of polyamine synthesis, inhibitors of DNA fragmentation. Percentage of apoptotic cells was statistically higher in patients with HT than in those with euthyroid goiter, with significant increase of caspase 32. Genes for Bcl-2 and Bax proteins are under the transcriptional control of p53. In TAD-2 cell cultures, apoptosis is p53-independed, suggesting that DNA damage is not primarily evoked by potassium iodide (KI. High concentrations of NaI increase the proportion of apoptotic cells in FTRL5 thyroid cell line. Iodide cytotoxicity is inhibited by a TPO inhibitor and is relieved with an anti-oxidant agent. Chronic iodine excess induces apoptosis and necrosis of thyroid follicular and endothelial cells, leading to thyroglobulin accumulation in connective tissue. Iodide excess requires peroxidase enzymatic activity to induce apoptosis. Ionic iodide is not directly toxic, whereas its molecular form I2 mediates the apoptotic effect of KI. [Project of the Serbian Ministry of Education, Science and Technological Development, Grant no. OI-175059

  16. Increased persistence of antifouling paint biocides when associated with paint particles

    International Nuclear Information System (INIS)

    Thomas, K.V.; McHugh, M.; Hilton, M.; Waldock, M.

    2003-01-01

    Release of biocides associated with paint particles into marinas may increase their persistence in the environment. - Current regulatory risk assessment procedures only assess the impact of antifouling paint biocides that are released through leaching from a painted surface. Hull cleaning activities can lead to particles of antifouling paint containing biocides to enter the environment. Comparative pseudo-first order anaerobic degradation rate constants and half-lives were determined for a selection of common antifouling paint booster biocides, their degradation products, and associated with paint particles. Anaerobic half-lives of <0.5 days were calculated for chlorothalonil, dichlofluanid, and SeaNine 211, between 1 and 3 days for DCPMU and DCPU, between 14 and 35 days for diuron and CPDU, and over 226 days for GS26575 and Irgarol 1051. Increased persistence was observed when the compounds were introduced to sediments associated with antifouling paint particles. When present as antifouling paint particles, an increased half-life of 9.9 days for SeaNine 211 and 1.4 days was calculated for dichlofluanid, no significant degradation was observed for diuron. It is suspected that this is due to much of the biocide being initially bound within the matrix of the paint particle that is slowly released through dissolution processes into the sediment pore water prior to degradation. The release of booster biocides associated with paint particles into marinas has the potential to lead to their accumulation unless activities such as hull cleaning are strictly regulated

  17. Increased persistence of antifouling paint biocides when associated with paint particles

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, K.V.; McHugh, M.; Hilton, M.; Waldock, M

    2003-05-01

    Release of biocides associated with paint particles into marinas may increase their persistence in the environment. - Current regulatory risk assessment procedures only assess the impact of antifouling paint biocides that are released through leaching from a painted surface. Hull cleaning activities can lead to particles of antifouling paint containing biocides to enter the environment. Comparative pseudo-first order anaerobic degradation rate constants and half-lives were determined for a selection of common antifouling paint booster biocides, their degradation products, and associated with paint particles. Anaerobic half-lives of <0.5 days were calculated for chlorothalonil, dichlofluanid, and SeaNine 211, between 1 and 3 days for DCPMU and DCPU, between 14 and 35 days for diuron and CPDU, and over 226 days for GS26575 and Irgarol 1051. Increased persistence was observed when the compounds were introduced to sediments associated with antifouling paint particles. When present as antifouling paint particles, an increased half-life of 9.9 days for SeaNine 211 and 1.4 days was calculated for dichlofluanid, no significant degradation was observed for diuron. It is suspected that this is due to much of the biocide being initially bound within the matrix of the paint particle that is slowly released through dissolution processes into the sediment pore water prior to degradation. The release of booster biocides associated with paint particles into marinas has the potential to lead to their accumulation unless activities such as hull cleaning are strictly regulated.

  18. Painting

    DEFF Research Database (Denmark)

    Petersen, Anne Ring

    2012-01-01

    and discursive battles over the essentially self-reflective question of “What is painting?” Over the last decades it has also become an intermedial laboratory in which artists experiment with developing a connective aesthetic in the interface between painting and other media. Accordingly, it is has become...

  19. Preparation of precipitated barium sulphate from Egyptian barytes ore and its application in paints

    International Nuclear Information System (INIS)

    El-Sawy, S.M.; Ahmed, N.M.; Abd El-Ghaffar, M.A.

    2005-01-01

    Precipitated barium sulphate (Blank fixe) was prepared and evaluated as an extender pigment, making use of the naturally occurring Egyptian barytes ore. X-ray diffraction patterns, transmission electron microscope, thermal gravimetric analysis, color measurements, specific gravity, oil absorption, bulking value, bleed resistance, hydrogen ion concentration, permanence for light and heat and chemical resistance were different methods used for characterization and evaluation of the prepared pigment. Medium oil alkyd resin, melamine-alkyd and epoxy resin were used as different binding media for the application and testing of the prepared pigments as an extender- in some paint formulations, this was done in comparison with a commercial imported blank fixe sample and the Egyptian barytes ore that it was prepared from. It was found that; a white bright fine powder of precipitated barium sulfate could be successfully prepared from the locally abundant Egyptian barytes ore. It has a suitable properties as an extender pigment. Paints pigmented with blank fixe offered favourable rheological and protective properties exceeding that of the imported commercial sample and the ore that was prepared from

  20. Chemisorption of organic iodine compounds forming from fission isotopes of radioactive iodine

    International Nuclear Information System (INIS)

    Tot, G.; Galina, F.; Zel'd, E.

    1977-01-01

    Studied is ethyl iodine adsorption, labelled by iodine 131, on palladium black and on aluminium oxide activized by palladium. The desorption of adsorbed iodine in the temperature range of 20-600 deg C by the mass spectroscopy and thermal gravimetric methods was investigated. At the ethyl iodine and palladium interaction the bond between carbon and iodine in the ethyl iodine molecule breaks down and extracting iodine reacts with palladium, forming a stable compound at high temperatures. Desorption of adsorbed iodine is insignificant up to the temperatures of 250-300 deg C. Thus, sorbents, containing palladium, may be successfully applied for iodine absorption from the organic iodine compounds. These compounds spontaneously appear from the iodine fragment ratio isotopes during their interaction with some environmental organic impurities

  1. Mitigation of release of volatile iodine species during severe reactor accidents - a novel reliable process of safety technology

    International Nuclear Information System (INIS)

    Guentay, S.; Bruchertseifer, H.

    2010-01-01

    In severe accidents, a significant risk for public health may be generated as a result of release of the gaseous iodine species into the environment through the containment leaks or containment venting filter systems with low retention efficiency. The elemental iodine and volatile organic iodides are the main gaseous iodine species in the containment. Potential release of large quantities of gaseous elemental iodine from the reactor coolant system or its radiolytic generation in the containment sump constitute the key source of gaseous elemental iodine in containment atmosphere. Iodine paint reactions as well as the reaction of iodine with organic residuals in sump water are the main mechanisms for the generation of high volatile organic iodides in the containment. Although very much desired, significant research activities conducted in 70's unfortunately did not create any technically feasible solution to mitigate iodine release into the environment under prevailing conditions. Development of a process leading to a fast, comprehensive and reliable retention of volatile iodine species in aqueous solution with an aim to implement for the severe accident management applications has been subject of a research project in the recent years at Paul Scherrer Institut. The process developed utilizes simultaneous use of two customary technical chemical additives in an aqueous solution. The results of the experimental program have demonstrated a fast and reliable destruction of high volatile organic iodine species and fast reduction of elemental iodine into iodide ions in aqueous solutions and an efficient mitigation of the re-formation of gaseous iodine from iodide ions. Investigations covered a broad range of anticipated severe accident conditions in the containment. The project additionally focused on possible application of the process to existing containment venting filter systems, specifically as a passive add-on for back-fitting. This paper describes the process

  2. Altering iodine metabolism in the calf by feeding iodine-binding agents

    International Nuclear Information System (INIS)

    Miller, J.K.; Swanson, E.W.; Lyke, W.A.; Byrne, W.F.

    1975-01-01

    Effects of feeding cottonseed meal and anion-exchange resin on iodine absorption and excretion by calves were investigated. Each additional amount of resin fed from 0.3 to 3.5 g/kg body weight further increased fecal excretion from single oral iodine-131 and intravenous iodine-125 doses. By feeding 3 to 10 g cottonseed meal/kg body weight, excretion of oral iodine-131 given daily was increased 7 to 94 percent in feces and reduced as much as 35 percent in urine, but plasma iodine-131 was not changed. Introducing 1 g resin/kg body weight daily into the diet increased fecal iodine-131 excretion three to five times that with cottonseed meal alone and reduced both plasma and urinary iodine-131. The same amount of resin fed daily had similar effects on excretion of iodine-131 injected subcutaneously each day. Although iodine depletion by a highly efficient iodine binder (resin) in the gastrointestinal tract is probable, iodine binding by a natural feed constituent (cottonseed meal) was relatively inefficient. (U.S.)

  3. Altering iodine metabolism in the calf by feeding iodine-binding agents

    International Nuclear Information System (INIS)

    Miller, J.K.; Swanson, E.W.; Lyke, W.A.; Byrne, W.F.

    1975-01-01

    Effects of feeding cottonseed meal and anion-exchange resin on iodine absorption and excretion by calves were investigated. Each additional amount of resin fed from 0.3 to 3.5 g/kg body weight further increased fecal excretion from single oral iodine-131 and intravenous iodine-125 doses. By feeding 3 to 10 g cottonseed meal/kg body weight, excretion of oral iodine-131 given daily was increased 7 to 94 percent in feces and reduced as much as 35 percent in urine, but plasma iodine-131 was not changed. Introducing 1 g resin/kg body weight daily into the diet increased fecal iodine-131 excretion three to five times that with cottonseed meal alone and reduced both plasma and urinary iodine-131. The same amount of resin fed daily had similar effects on excretion of iodine-131 injected subcutaneously each day. Although iodine depletion by a highly efficient iodine binder (resin) in the gastrointestinal tract is probable, iodine binding by a natural feed constituent (cottonseed meal) was relatively inefficient. (auth)

  4. Structural investigation of e-beam cured epoxy resins through solid state NMR

    International Nuclear Information System (INIS)

    Alessi, Sabina; Spinella, Alberto; Caponetti, Eugenio; Dispenza, Clelia; Spadaro, Giuseppe

    2012-01-01

    In this paper the network structure of e-beam cured DGEBF based epoxy resins is investigated. Two epoxy systems, having different reactivity and cured in different process conditions, were analyzed through solid state NMR spectroscopy. The analysis shows that the more reactive system has higher cross-linking density and higher uniformity of network distribution. Similar information were obtained, in a previous work, on the same systems through dynamic mechanical thermal analysis. It is worth noting that unlike DMTA tests, which interfere with the molecular structure of the analyzed material, due to the heating during the analysis itself, more reliable information, without any artefact, are obtained by solid state NMR, carried out at constant room temperature. - Highlights: ► The structure of two e-beam cured epoxy systems is investigated through solid state NMR. ► The aim is to have direct information about the structure without inducing modifications. ► The different molecular structures are able to emphasize the response of solid state NMR. ► T 1 H, T 1ρ H and T CH measurements indicate different cross-linking degrees. ► The NMR results are in agreement with DMTA analysis performed in a previous paper.

  5. RAIM-A model for iodine behavior in containment under severe accident condition

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Han Chul; Cho, Yeong Hun [Korea Institute of Nuclear Safety, Daejeon (Korea, Republic of)

    2015-12-15

    Following a severe accident in a nuclear power plant, iodine is a major contributor to the potential health risks for the public. Because the amount of iodine released largely depends on its volatility, iodine's behavior in containment has been extensively studied in international programs such as International Source Term Programme-Experimental Program on Iodine Chemistry under Radiation (EPICUR), Organization for Economic Co-operation and Development (OECD)-Behaviour of Iodine Project, and OECD-Source Term Evaluation and Mitigation. Korea Institute of Nuclear Safety (KINS) has joined these programs and is developing a simplified, stand-alone iodine chemistry model, RAIM (Radio-Active Iodine chemistry Model), based on the IMOD methodology and other previous studies. This model deals with chemical reactions associated with the formation and destruction of iodine species and surface reactions in the containment atmosphere and the sump in a simple manner. RAIM was applied to a simulation of four EPICUR tests and one Radioiodine Test Facility test, which were carried out in aqueous or gaseous phases. After analysis, the results show a trend of underestimation of organic and molecular iodine for the gas-phase experiments, the opposite of that for the aqueous-phase ones, whereas the total amount of volatile iodine species agrees well between the experiment and the analysis result.

  6. Gas pipeline internal painting: an economical advantage; Uso da pintura interna em gasodutos: uma vantagem economica

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Christian E.; Santos, Paulo T. [Soco-Ril do Brasil S.A., Pindamonhangaba, SP (Brazil)]|[Faculdade de Engenharia Quimica de Lorena (FAENQUIL), SP (Brazil). Programa de Pos-graduacao em Engenharia Mecanica; Oliveira, Luiz C. [Confab Industrial S.A., Pindamonhangaba, SP (Brazil)]|[Faculdade de Engenharia Quimica de Lorena (FAENQUIL), SP (Brazil). Programa de Pos-graduacao em Engenharia Mecanica; Campos, Paulo H. [Confab Industrial S.A., Pindamonhangaba, SP (Brazil)

    2003-07-01

    Focusing the fabulous financial losses due to the corrosion problems, it had been necessary increase the range of new technologies and developments regarding material protection. The application of internal painting systems have become the most employed protection technical, showing a lot of benefits: improved flow characteristics of gas, reduced energy consumption of pumping, reduced pressure drops, easily application, inspection and maintenance, faster commissioning, reduced deposition of condensate and microorganism, excellent preventing corrosion during storage and operation, and others. The present paper describe the advantages and the technical and financial benefits of liquid epoxy internal coating. (author)

  7. Synthesis of polyoxometalate-loaded epoxy composites

    Science.gov (United States)

    Anderson, Benjamin J

    2014-10-07

    The synthesis of a polyoxometalate-loaded epoxy uses a one-step cure by applying an external stimulus to release the acid from the polyoxometalate and thereby catalyze the cure reaction of the epoxy resin. Such polyoxometalate-loaded epoxy composites afford the cured epoxy unique properties imparted by the intrinsic properties of the polyoxometalate. For example, polyoxometalate-loaded epoxy composites can be used as corrosion resistant epoxy coatings, for encapsulation of electronics with improved dielectric properties, and for structural applications with improved mechanical properties.

  8. Recovery of iodine as iodine-125 from biological materials prior to assay

    International Nuclear Information System (INIS)

    Jones, G.B.; Belling, G.B.; Buckley, R.A.

    1979-01-01

    In biological tissues iodine is usually present as iodoamino acids or iodoproteins. The organic material must be oxidised and the iodine converted into iodate prior to the final spectrophotometric determination. At parts per billion (10 9 ) levels, recoveries of added iodine are difficult to measure precisely as iodine can easily be lost from the sample and added inorganic iodine may not be recovered in the same proportions as the naturally occurring iodine. Iodine-125 provides a much more sensitive, specific and accurate means of testing the recovery of nanogram amounts of iodine from biological tissues and it can be incorporated into tissues in the naturally occurring compounds. Plants can be grown in a solution culture containing iodine-125 and animals can be injected with iodine-125 to provide tissues where naturally occurring iodine compounds are labelled with radioactive iodine. These tissues can be used to examine the recovery of iodine after oven drying, freeze drying, alkali ashing and acid digestion of the samples. Experimental details are given for spinach, tobacco, oats, cauliflower and thyroid. Results are given and discussed. (author)

  9. Iodine from bacterial iodide oxidization by Roseovarius spp. inhibits the growth of other bacteria.

    Science.gov (United States)

    Zhao, Dan; Lim, Choon-Ping; Miyanaga, Kazuhiko; Tanji, Yasunori

    2013-03-01

    Microbial activities in brine, seawater, or estuarine mud are involved in iodine cycle. To investigate the effects of the microbiologically induced iodine on other bacteria in the environment, a total of 13 bacteria that potentially participated in the iodide-oxidizing process were isolated from water or biofilm at a location containing 131 μg ml(-1) iodide. Three distinct strains were further identified as Roseovarius spp. based on 16 S rRNA gene sequences after being distinguished by restriction fragment length polymorphism analysis. Morphological characteristics of these three Roseovarius spp. varied considerably across and within strains. Iodine production increased with Roseovarius spp. growth when cultured in Marine Broth with 200 μg ml(-1) iodide (I(-)). When 10(6) CFU/ml Escherichia coli, Pseudomonas aeruginosa, and Bacillus pumilus were exposed to various concentrations of molecular iodine (I(2)), the minimum inhibitory concentrations (MICs) were 0.5, 1.0, and 1.0 μg ml(-1), respectively. However, fivefold increases in the MICs for Roseovarius spp. were obtained. In co-cultured Roseovarius sp. IOB-7 and E. coli in Marine Broth containing iodide (I(-)), the molecular iodine concentration was estimated to be 0.76 μg ml(-1) after 24 h and less than 50 % of E. coli was viable compared to that co-cultured without iodide. The growth inhibition of E. coli was also observed in co-cultures with the two other Roseovarius spp. strains when the molecular iodine concentration was assumed to be 0.52 μg ml(-1).

  10. Iodine leaflets in chapter D5 'Distribution of iodine pills'

    International Nuclear Information System (INIS)

    1981-01-01

    Jodine leaflet A will be distributed together with iodine pills in a nuclear disaster. Iodine leaflet B is suitable for informing the public in advance. Iodine leaflet C informs physicians in a scientific way on the benefits and risk of iodine pills. (orig./HP) [de

  11. Povidone-Iodine-Based Polymeric Nanoparticles for Antibacterial Applications.

    Science.gov (United States)

    Gao, Tianyi; Fan, Hongbo; Wang, Xinjie; Gao, Yangyang; Liu, Wenxin; Chen, Wanjun; Dong, Alideertu; Wang, Yan-Jie

    2017-08-09

    As microbial contamination is becoming more and more serious, antibacterial agents play an important role in preventing and removing bacterial pathogens from microbial pollution in our daily life. To solve the issues with water solubility and antibacterial stability of PVP-I 2 (povidone-iodine) as a strong antibacterial agent, we successfully obtain hydrophobic povidone-iodine nanoparticles (povidone-iodine NPs) by a two-step method related to the advantage of nanotechnology. First, the synthesis of poly(N-vinyl-2-pyrrolidone-co-methyl methacrylate) nanoparticles, i.e., P(NVP-MMA) NPs, was controlled by tuning a feed ratio of NVP to MMA. Then, the products P(NVP-MMA) NPs were allowed to undergo a complexation reaction with iodine, resulting in the formation of a water-insoluble antibacterial material, povidone-iodine NPs. It is found that the feed ratio of NVP to MMA has an active effect on morphology, chemical composition, molecular weight, and hydrophilic-hydrophobic properties of the P(NVP-MMA) copolymer after some technologies, such as SEM, DLS, elemental analysis, 1 H NMR, GPC, and the contact angle test, were used in the characterizations. The antibacterial property of povidone-iodine NPs was investigated by using Escherichia coli (E. coli), Staphylococcus aureus (S. aureus), and Pseudomonas aeruginosa (P. aeruginosa) as model bacteria with the colony count method. Interestingly, three products, such as glue, ink, and dye, after the incorporation of povidone-iodine NPs, show significant antibacterial properties. It is believed that, with the advantage of nanoscale morphology, the final povidone-iodine NPs should have great potential for utilization in various fields where antifouling and antibacterial properties are highly required.

  12. Perchlorate, iodine supplements, iodized salt and breast milk iodine content

    Energy Technology Data Exchange (ETDEWEB)

    Kirk, Andrea B. [Department of Epidemiology, School of Public Health, University of North Texas Health Sciences Center, 3500 Camp Bowie Blvd., Fort Worth, TX 76107 (United States); Kroll, Martina; Dyke, Jason V.; Ohira, Shin-Ichi; Dias, Rukshan A.; Dasgupta, Purnendu K. [Department of Chemistry and Biochemistry, 700 Planetarium Place, University of Texas at Arlington, Arlington, TX 76019 (United States)

    2012-03-15

    This study was undertaken to determine if increasing maternal iodine intake through single dose tablets will decrease breast milk concentrations of the iodine-uptake inhibitor, perchlorate, through competitive inhibition. We also sought to determine if the timing of supplementation influences the fraction of iodine excreted in milk versus urine and to compare the effectiveness of iodized salt as a means of providing iodine to breastfed infants. Thirteen women who did not use supplements, seven of whom used iodized salt and six of whom used non-iodized salt, submitted four milk samples and a 24-h urine collection daily for three days. Women repeated the sampling protocol for three more days during which {approx} 150 {mu}g of iodine were taken in the evening and again for three days with morning supplementation. Samples were analyzed using isotope-dilution inductively-coupled plasma-mass spectrometry for iodine and isotope-dilution ion chromatography-tandem mass spectrometry for perchlorate. No statistically significant differences were observed in milk iodine or perchlorate concentrations during the two treatment periods. Estimated perchlorate intake was above the U.S. National Academy of Sciences suggested reference dose for most infants. Single daily dose iodine supplementation was not effective in decreasing milk perchlorate concentrations. Users of iodized salt had significantly higher iodine levels in milk than non-users. Iodized salt may be a more effective means of iodine supplementation than tablets. - Highlights: Black-Right-Pointing-Pointer Estimated infant exposures to perchlorate were, on a {mu}g/kg basis, {approx} 5 Multiplication-Sign higher than those of mothers. Black-Right-Pointing-Pointer Daily supplements are less effective than iodized salt in providing iodine to lactating women. Black-Right-Pointing-Pointer Low iodine and high perchlorate in milk may place infants at risk of iodine deficiency.

  13. Pyrolysis responses of kevlar/epoxy composite materials on laser irradiating

    Science.gov (United States)

    Liu, Wei-ping; Wei, Cheng-hua; Zhou, Meng-lian; Ma, Zhi-liang; Song, Ming-ying; Wu, Li-xiong

    2017-05-01

    The pyrolysis responses of kevlar/epoxy composite materials are valuable to study in a case of high temperature rising rate for its widely application. Distinguishing from the Thermal Gravimetric Analysis method, an apparatus is built to research the pyrolysis responses of kevlar/epoxy composite materials irradiated by laser in order to offer a high temperature rising rate of the sample. By deploying the apparatus, a near real-time gas pressure response can be obtained. The sample mass is weighted before laser irradiating and after an experiment finished. Then, the gas products molecular weight and the sample mass loss evolution are derived. It is found that the pressure and mass of the gas products increase with the laser power if it is less than 240W, while the molecular weight varies inversely. The variation tendency is confusing while the laser power is bigger than 240W. It needs more deeper investigations to bring it to light.

  14. Iodine deficiency and iodine excess in Jiangsu Province, China

    NARCIS (Netherlands)

    Zhao, J.

    2001-01-01

    Keywords:
    iodine deficiency, iodine excess, endemic goiter, drinking water, iodine intake, thyroid function, thyroid size, iodized salt, iodized oil, IQ, physical development, hearing capacity, epidemiology, meta-analysis, IDD, randomized trial, intervention, USA, Bangladesh,

  15. Molecular structures and thermodynamic properties of monohydrated gaseous iodine compounds: Modelling for severe accident simulation

    Science.gov (United States)

    Sudolská, Mária; Cantrel, Laurent; Budzák, Šimon; Černušák, Ivan

    2014-03-01

    Monohydrated complexes of iodine species (I, I2, HI, and HOI) have been studied by correlated ab initio calculations. The standard enthalpies of formation, Gibbs free energy and the temperature dependence of the heat capacities at constant pressure were calculated. The values obtained have been implemented in ASTEC nuclear accident simulation software to check the thermodynamic stability of hydrated iodine compounds in the reactor coolant system and in the nuclear containment building of a pressurised water reactor during a severe accident. It can be concluded that iodine complexes are thermodynamically unstable by means of positive Gibbs free energies and would be represented by trace level concentrations in severe accident conditions; thus it is well justified to only consider pure iodine species and not hydrated forms.

  16. Eco-friendly Oxidative Iodination of Various Arenes with Sodium Percarbonate as the Oxidantâ€

    Directory of Open Access Journals (Sweden)

    Lech Skulski

    2005-10-01

    Full Text Available Six easy laboratory procedures are presented for the oxidative iodination ofvarious aromatics, mostly arenes, with either molecular iodine or potassium iodide (usedas the sources of iodinating species, I or I3 , in the presence of sodium percarbonate(SPC, a stable, cheap, easy to handle, and eco-friendly commercial oxidant.

  17. Iodine in diet

    Science.gov (United States)

    Diet - iodine ... Many months of iodine deficiency in a person's diet may cause goiter or hypothyroidism . Without enough iodine, ... and older children. Getting enough iodine in the diet may prevent a form of physical and intellectual ...

  18. Iodine and thyroid function

    Directory of Open Access Journals (Sweden)

    Hye Rim Chung

    2014-03-01

    Full Text Available Severe iodine deficiency causes hypothyroidism that results in impaired somatic growth and motor development in children. Mild and moderate iodine deficiencies cause multifocal autonomous growth of thyroid, which results in thyrotoxicosis. On the other hand, iodine excess is associated with the development of hypothyroidism and thyroid autoimmunity. In areas of iodine deficiency, a sudden increase in iodine intake is associated with transient hyperthyroidism. Recent studies demonstrated that long-term thyroid function of subjects who experienced both iodine deficiency and iodine excess during childhood tended to be abnormal despite optimization of their current iodine intake. Iodine status in the Korean Peninsula is very unique because people in the Republic of Korea have been shown to have predominantly excessive iodine levels, whereas the Democratic People's Republic of Korea is known to be an iodine-deficient area. Further research is warranted to verify the optimal ranges of iodine intake and to clarify the effects of iodine intake on thyroid disorders in the Korean Peninsula.

  19. Iodine Deficiency

    NARCIS (Netherlands)

    Zimmermann, M.B.

    2009-01-01

    Iodine deficiency has multiple adverse effects in humans, termed iodine deficiency disorders, due to inadequate thyroid hormone production. Globally, it is estimated that 2 billion individuals have an insufficient iodine intake, and South Asia and sub-Saharan Africa are particularly affected.

  20. Egyptian Tomb Painting.

    Science.gov (United States)

    Schroeder, Liesa

    1999-01-01

    Provides an activity where sixth-grade students replicated the Egyptian art form of tomb painting. Explains that the students researched information about Egyptian culture and history in order to familiarize themselves with Egyptian wall-painting style. Discusses the process of creating tomb paintings in detail. (CMK)

  1. Evaluation method of iodine re-evolution from an in-containment water pool after a loss of coolant accident, Part II: Evaluation of pH and iodine re-evolution

    International Nuclear Information System (INIS)

    Kim, Tae Hyeon; Jeong, Ji Hwan

    2016-01-01

    Highlights: • It is required to evaluate re-evolved iodine from sump water after LOCA. • Transport of iodine and chemicals influencing pH were analyzed using CFD. • Chemical conditions of the iodine-rich region suppress iodine re-evolution. • The current evaluation method for I 2 re-evolution is excessively conservative. - Abstract: Radioactive iodine that is released during a postulated loss of coolant accident is dissolved into the containment spray water and transported into the in-containment refueling water storage tank (IRWST). The re-evolution of iodine from the water is a safety concern. In this study, three-dimensional computational fluid dynamics (CFD) analyses are conducted in order to analyze the transport of chemical species including iodine in the IRWST and to calculate the amount of iodine that re-evolves from the IRWST water. The CFD analyses demonstrate that the pH of water is high where the iodine concentration is high. Considering that the creation rate of molecular iodine declines as the pH increases, it can be understood that the iodine re-evolution is not so strong in practical situations because the chemical conditions of the iodine-rich region suppress the re-evolution of the iodine. In addition, four different methods for evaluating the amount of re-evolved iodine are examined. The amount of re-evolved iodine calculated using the total-volume-average values, which are currently used for safety analyses, appear to be significantly higher than those determined using other methods. The amount of re-evolved iodine estimated using a realistic method with a conservative assumption of volatilization appears to be approximately one thousandth of that evaluated using the current method. This implies that the current method is very conservative.

  2. Black molecular adsorber coatings for spaceflight applications

    Science.gov (United States)

    Abraham, Nithin S.; Hasegawa, Mark M.; Straka, Sharon A.

    2014-09-01

    The molecular adsorber coating is a new technology that was developed to mitigate the risk of on-orbit molecular contamination on spaceflight missions. The application of this coating would be ideal near highly sensitive, interior surfaces and instruments that are negatively impacted by outgassed molecules from materials, such as plastics, adhesives, lubricants, epoxies, and other similar compounds. This current, sprayable paint technology is comprised of inorganic white materials made from highly porous zeolite. In addition to good adhesion performance, thermal stability, and adsorptive capability, the molecular adsorber coating offers favorable thermal control characteristics. However, low reflectivity properties, which are typically offered by black thermal control coatings, are desired for some spaceflight applications. For example, black coatings are used on interior surfaces, in particular, on instrument baffles for optical stray light control. Similarly, they are also used within light paths between optical systems, such as telescopes, to absorb light. Recent efforts have been made to transform the white molecular adsorber coating into a black coating with similar adsorptive properties. This result is achieved by optimizing the current formulation with black pigments, while still maintaining its adsorption capability for outgassing control. Different binder to pigment ratios, coating thicknesses, and spray application techniques were explored to develop a black version of the molecular adsorber coating. During the development process, coating performance and adsorption characteristics were studied. The preliminary work performed on black molecular adsorber coatings thus far is very promising. Continued development and testing is necessary for its use on future contamination sensitive spaceflight missions.

  3. Reactivities of some aldoses towards iodine in alkaline

    International Nuclear Information System (INIS)

    Azmat, R.; Nizami, S.S.

    2005-01-01

    The kinetics studies of oxidation of some reducing sugars by aqueous alkaline solution of iodine investigated. Results demonstrated that iodine in the presence of alkali converted into hypoiodous acid which was effective oxidizing species. Reaction between iodine and sugars was slowest reaction. The rate of oxidation of sugars was affected by change in pH of the medium and maximum at pH 11.4 where the concentration of hypoiodous acid was maximum which oxidized the sugars into respective acids. The rate of oxidation followed first order kinetics with respect to substrate and obeyed zero order kinetics with that of iodine. Change in ionic strength of the medium showed no effect on the rate of oxidation indicating that reaction occurred between molecular species and there was no ionic species present in the rate determining step. Reaction was affected by the change in temperature and value of energy of activation corresponding to glucose, galactose, D-mannose and L-arabinose were 10.16 kj/mol, 12.17 kj/mol, 14.00 kj/mol and 20.22 kj/mol respectively. (author)

  4. Radiolytic oxidation of iodine in the containment at high temperature and dose rate

    International Nuclear Information System (INIS)

    Guilbert, S.; Bosland, L.; Jacquemain, D.; Clement, B.; Andreo, F.; Ducros, G.; Dickinson, S.; Herranz, L.; Ball, J.

    2007-01-01

    Iodine Chemistry is one of the areas of top interest in the field of nuclear power plants (NPP) severe accidents studies. The strong radiological impact of iodine on man health and environment, mostly through its isotope I-131, has made it a key point to get an accurate prediction of the potential iodine release from the NPP containment to the environment in the low probable event of an accident leading to core melt. Released from the fuel as a gaseous form, iodine enters the containment in gaseous or particulate form and undergoes deposition processes that eventually take it to the containment surfaces and sump. Once in the sump, iodine, when present as soluble compounds, gets dissolved as non volatile iodide (I-). Nonetheless, in the presence of radiation and particularly in acidic sumps, iodine can be oxidized to volatile forms such as molecular iodine (I 2 ) and can escape from the sump to the containment atmosphere (sump radiolysis process), thus increasing its potential contribution to the iodine source term. Iodine sump radiolysis has been extensively studied experimentally in the past decades. Experiments have revealed that parameters such as pH, temperature and total iodine concentration have a large impact on iodine volatility. However, experimental data at elevated temperatures (> 80 O C) and elevated dose rates (> 1 kGy.h -1 ) anticipated in containment during a postulated severe accident are too scarce to provide for these relevant conditions an accurate determination of the volatile iodine fractions. Furthermore, some data were obtained from post-irradiation analysis and iodine concentration may be underestimated at the time of measurements compared with that during irradiation, due to post-irradiation reactions. To complete the existing database, the EPICUR program was launched by IRSN (Institut de Radioprotection et de Surete Nucleaire) and experiments have been performed in the frame of the International Source Term Program (ISTP) to provide on

  5. Experimental study on iodine chemistry (EXSI) - Containment experiments with elemental iodine

    Energy Technology Data Exchange (ETDEWEB)

    Kaerkelae, T.; Auvinen, A. (VTT Technical Research Centre of Finland (Finland)); Holm, J.; Ekberg, C. (Chalmers Univ. of Technology (Sweden)); Glaenneskog, H. (Vattenfall Power Consultant (Sweden))

    2009-10-15

    The behaviour of iodine during a severe accident has been studied in several experimental programs, ranging from the large-scale PHEBUS FP tests and intermediate-scale ThAI tests to numerous separate effect studies. Oxidation of iodine in gas phase has been one of the greatest remaining uncertainties in iodine behaviour during a severe accident. In this study the possible formation of iodine oxide aerosol due to radiolytic oxidation of gaseous iodine is experimentally tested and the reaction products are analysed. The experimental facility applied in this study is based on the sampling system built at VTT for ISTP program project CHIP conducted IRSN. The experimental facility and the measuring technology are sophisticated and unique in the area of nuclear research as well as in the field of aerosol science. The results from the experiments show an extensive particle formation when ozone and gaseous iodine react with each other. The formed particles were collected on filters, while gaseous iodine was trapped into bubbles. The particles were iodine oxides and the size of particles was approximately 100 nm. The transport of gaseous iodine through the facility decreased when both gaseous iodine and ozone were fed together into facility. Experimental study on radiolytic oxidation of iodine was conducted in co-operation between VTT and Chalmers University of Technology as a part of the NKS-R programs. (author)

  6. Experimental study on iodine chemistry (EXSI) - Containment experiments with elemental iodine

    International Nuclear Information System (INIS)

    Kaerkelae, T.; Auvinen, A.; Holm, J.; Ekberg, C.; Glaenneskog, H.

    2009-10-01

    The behaviour of iodine during a severe accident has been studied in several experimental programs, ranging from the large-scale PHEBUS FP tests and intermediate-scale ThAI tests to numerous separate effect studies. Oxidation of iodine in gas phase has been one of the greatest remaining uncertainties in iodine behaviour during a severe accident. In this study the possible formation of iodine oxide aerosol due to radiolytic oxidation of gaseous iodine is experimentally tested and the reaction products are analysed. The experimental facility applied in this study is based on the sampling system built at VTT for ISTP program project CHIP conducted IRSN. The experimental facility and the measuring technology are sophisticated and unique in the area of nuclear research as well as in the field of aerosol science. The results from the experiments show an extensive particle formation when ozone and gaseous iodine react with each other. The formed particles were collected on filters, while gaseous iodine was trapped into bubbles. The particles were iodine oxides and the size of particles was approximately 100 nm. The transport of gaseous iodine through the facility decreased when both gaseous iodine and ozone were fed together into facility. Experimental study on radiolytic oxidation of iodine was conducted in co-operation between VTT and Chalmers University of Technology as a part of the NKS-R programs. (author)

  7. Color alteration of the paint used for iris painting in ocular prostheses

    Directory of Open Access Journals (Sweden)

    Aline Úrsula Rocha Fernandes

    2009-12-01

    Full Text Available The purpose of this study was to assess color alteration of the paints used for iris painting in artificial eyes. Five disks of heat cured acrylic resin were confectioned by microwave energy for each paint analyzed, in a total of 40 specimens. Each specimen consisted of a colorless acrylic resin disk and another of equal size, of scleral white colored acrylic resin, with the painting interposed between the two disks. The specimens were submitted to an accelerated aging process in a chamber under ultraviolet radiation for 1,008 hours. To assess color variation, a reflective spectrophotometer was used. The results were statistically analyzed by ANOVA and the Tukey test (p < 0.05. All the paints underwent chromatic alteration. The oil paint presented the highest resistance to accelerated aging.

  8. Epoxy-based carbon nanotubes reinforced composites

    CSIR Research Space (South Africa)

    Kesavan Pillai, Sreejarani

    2011-04-01

    Full Text Available of the three major epoxy resin producers worldwide [May, 1987]. Epoxy resin is most commonly used as a matrix for advanced composites due to their superior thermal, mechanical and electrical properties; dimensional stability and chemical resistance. Epoxy... and modifiers to create products with an almost unlimited range and variety of performance properties [The epoxy book, 2000]. Epoxy resins are widely used as high-grade synthetic resins, for example, in the electronics, aeronautics and astronautic industries...

  9. Raim – A model for iodine behavior in containment under severe accident condition

    Directory of Open Access Journals (Sweden)

    Han-Chul Kim

    2015-12-01

    Full Text Available Following a severe accident in a nuclear power plant, iodine is a major contributor to the potential health risks for the public. Because the amount of iodine released largely depends on its volatility, iodine's behavior in containment has been extensively studied in international programs such as International Source Term Programme-Experimental Program on Iodine Chemistry under Radiation (EPICUR, Organization for Economic Co-operation and Development (OECD-Behaviour of Iodine Project, and OECD-Source Term Evaluation and Mitigation. Korea Institute of Nuclear Safety (KINS has joined these programs and is developing a simplified, stand-alone iodine chemistry model, RAIM (Radio-Active Iodine chemistry Model, based on the IMOD methodology and other previous studies. This model deals with chemical reactions associated with the formation and destruction of iodine species and surface reactions in the containment atmosphere and the sump in a simple manner. RAIM was applied to a simulation of four EPICUR tests and one Radioiodine Test Facility test, which were carried out in aqueous or gaseous phases. After analysis, the results show a trend of underestimation of organic and molecular iodine for the gas-phase experiments, the opposite of that for the aqueous-phase ones, whereas the total amount of volatile iodine species agrees well between the experiment and the analysis result.

  10. Iodine intake in Ireland

    International Nuclear Information System (INIS)

    Smith, P.P.A.; Hetherton, A.M.; O'Carroll, D.; Smith, D.F.; O'Halloran, M.J.; O'Donovan, D.K.

    1988-01-01

    A study of urinary iodine excretion and thyroid gland uptake of radioactive iodine 131 I was undertaken in the Dublin area with a view to providing data on the current iodine status in Ireland. A mean urinary iodine excretion of 118±82μg/gram creatinine (Median 96) obtained from 821 subjects attending general hospital outpatient clinics in the Dublin area in 1987, while excluding severe iodine deficiency in this particular cohort, obscured the fact that 250 (30%) had iodine excretion values ≤70 μ/g creatinine, a value approximating to the minimum daily iodine requirement. The results provide sufficient evidence of sporadic iodine deficiency to justify a more widespread study of the iodine status of the Irish population with a view to making recommendations on the possible need for iodine prophylaxis

  11. Molecular Modeling for Calculation of Mechanical Properties of Epoxies with Moisture Ingress

    Science.gov (United States)

    Clancy, Thomas C.; Frankland, Sarah J.; Hinkley, J. A.; Gates, T. S.

    2009-01-01

    Atomistic models of epoxy structures were built in order to assess the effect of crosslink degree, moisture content and temperature on the calculated properties of a typical representative generic epoxy. Each atomistic model had approximately 7000 atoms and was contained within a periodic boundary condition cell with edge lengths of about 4 nm. Four atomistic models were built with a range of crosslink degree and moisture content. Each of these structures was simulated at three temperatures: 300 K, 350 K, and 400 K. Elastic constants were calculated for these structures by monitoring the stress tensor as a function of applied strain deformations to the periodic boundary conditions. The mechanical properties showed reasonably consistent behavior with respect to these parameters. The moduli decreased with decreasing crosslink degree with increasing temperature. The moduli generally decreased with increasing moisture content, although this effect was not as consistent as that seen for temperature and crosslink degree.

  12. Iodination of phenol

    International Nuclear Information System (INIS)

    Christiansen, J.V.; Feldthus, A.; Carlsen, L.

    1990-01-01

    Phenol is iodinated in aqueous solution at pH 5 (acetate buffer) by elemental iodine or, if the iodine is present as iodide, enzymatically controlled by peroxidases. Generally mono-, di- and triiodophenols are obtained, the overall product composition being virtually identical for the two iodination modes. However, there is a tendency to a higher para to ortho ratio for the enzymatically controlled reaction. The mutual ratios of the single iodophenols depends on the initial concentration ratio between phenol and the iodinating species. The first step in the iodination leads preferentially to substitution in the ortho position rather than in the para position in contract to e.g. the corresponding bromination. The relative rates of the competive reactions in the combined iodination scheme has been derived. (author) 2 tabs., 3 ills., 15 refs

  13. Iodine and Pregnancy

    OpenAIRE

    Yarrington, Christina; Pearce, Elizabeth N.

    2011-01-01

    Iodine is a necessary element for the production of thyroid hormone. We will review the impact of dietary iodine status on thyroid function in pregnancy. We will discuss iodine metabolism, homeostasis, and nutritional recommendations for pregnancy. We will also discuss the possible effects of environmental contaminants on iodine utilization in pregnant women.

  14. Mechanical Properties of Graphene Nanoplatelet/Carbon Fiber/Epoxy Hybrid Composites: Multiscale Modeling and Experiments

    Science.gov (United States)

    Hadden, C. M.; Klimek-McDonald, D. R.; Pineda, E. J.; King, J. A.; Reichanadter, A. M.; Miskioglu, I.; Gowtham, S.; Odegard, G. M.

    2015-01-01

    Because of the relatively high specific mechanical properties of carbon fiber/epoxy composite materials, they are often used as structural components in aerospace applications. Graphene nanoplatelets (GNPs) can be added to the epoxy matrix to improve the overall mechanical properties of the composite. The resulting GNP/carbon fiber/epoxy hybrid composites have been studied using multiscale modeling to determine the influence of GNP volume fraction, epoxy crosslink density, and GNP dispersion on the mechanical performance. The hierarchical multiscale modeling approach developed herein includes Molecular Dynamics (MD) and micromechanical modeling, and it is validated with experimental testing of the same hybrid composite material system. The results indicate that the multiscale modeling approach is accurate and provides physical insight into the composite mechanical behavior. Also, the results quantify the substantial impact of GNP volume fraction and dispersion on the transverse mechanical properties of the hybrid composite, while the effect on the axial properties is shown to be insignificant.

  15. Mechanical Properties of Graphene Nanoplatelet Carbon Fiber Epoxy Hybrid Composites: Multiscale Modeling and Experiments

    Science.gov (United States)

    Hadden, Cameron M.; Klimek-McDonald, Danielle R.; Pineda, Evan J.; King, Julie A.; Reichanadter, Alex M.; Miskioglu, Ibrahim; Gowtham, S.; Odegard, Gregory M.

    2015-01-01

    Because of the relatively high specific mechanical properties of carbon fiber/epoxy composite materials, they are often used as structural components in aerospace applications. Graphene nanoplatelets (GNPs) can be added to the epoxy matrix to improve the overall mechanical properties of the composite. The resulting GNP/carbon fiber/epoxy hybrid composites have been studied using multiscale modeling to determine the influence of GNP volume fraction, epoxy crosslink density, and GNP dispersion on the mechanical performance. The hierarchical multiscale modeling approach developed herein includes Molecular Dynamics (MD) and micromechanical modeling, and it is validated with experimental testing of the same hybrid composite material system. The results indicate that the multiscale modeling approach is accurate and provides physical insight into the composite mechanical behavior. Also, the results quantify the substantial impact of GNP volume fraction and dispersion on the transverse mechanical properties of the hybrid composite, while the effect on the axial properties is shown to be insignificant.

  16. Iodine

    Science.gov (United States)

    ... Health Information Supplement Fact Sheets Frequently Asked Questions Making Decisions What you Need To Know About Supplements Dietary ... mild iodine deficiency and of iodine supplements on cognitive ... breasts. It mainly affects women of reproductive age but can also occur ...

  17. Preparación y caracterización de filmes epoxi basados en aceite de linaza para aplicación

    OpenAIRE

    Gómez Carrera, Marta

    2015-01-01

    En este proyecto se preparan diferentes composiciones de filmes epoxi basados en aceite de linaza químicamente epoxidado (Epoxidized Linseed Oil-ELO) y su posterior curado con dos tipos de endurecedores, una poliaminoamida comercial y una poli(etilenimina) con dos pesos moleculares distintos. El objetivo final es la preparación de una pintura epoxi menos tóxica para el ser humano, sustituyendo parcialmente la molécula de diglicidil éter de bisfenol A (DGEBA), de las formulaciones epoxi, por m...

  18. Low-level seaweed supplementation improves iodine status in iodine-insufficient women.

    Science.gov (United States)

    Combet, Emilie; Ma, Zheng Feei; Cousins, Frances; Thompson, Brett; Lean, Michael E J

    2014-09-14

    Iodine insufficiency is now a prominent issue in the UK and other European countries due to low intakes of dairy products and seafood (especially where iodine fortification is not in place). In the present study, we tested a commercially available encapsulated edible seaweed (Napiers Hebridean Seagreens® Ascophyllum nodosum species) for its acceptability to consumers and iodine bioavailability and investigated the impact of a 2-week daily seaweed supplementation on iodine concentrations and thyroid function. Healthy non-pregnant women of childbearing age, self-reporting low dairy product and seafood consumption, with no history of thyroid or gastrointestinal disease were recruited. Seaweed iodine (712 μg, in 1 g seaweed) was modestly bioavailable at 33 (interquartile range (IQR) 28-46) % of the ingested iodine dose compared with 59 (IQR 46-74) % of iodine from the KI supplement (n 22). After supplement ingestion (2 weeks, 0·5 g seaweed daily, n 42), urinary iodine excretion increased from 78 (IQR 39-114) to 140 (IQR 103-195) μg/l (Pseaweed was palatable and acceptable to consumers as a whole food or as a food ingredient and effective as a source of iodine in an iodine-insufficient population. In conclusion, seaweed inclusion in staple foods would serve as an alternative to fortification of salt or other foods with KI.

  19. Micro-analytical study of interactions between oil and lead compounds in paintings

    International Nuclear Information System (INIS)

    Cotte, M.; Checroun, E.; Susini, J.; Walter, P.

    2007-01-01

    Oil paintings are complex hybrid materials, made of organic binders associated with inorganic minerals, susceptible to evolving over centuries. In particular, interactions of oil with lead compounds may give rise to the formation of lead soap aggregates, so-called protrusions. This phenomenon is studied here via X-ray and FTIR micro-analysis of an ancient painting dated from 1610. In complement, the synthesis of modern preparations, reconstructed from ancient recipes was assessed. Molecular and atomic images are obtained by combining synchrotron-based FTIR and X-ray fluorescence microscopies. Protrusions are identified in both ancient and modern samples, more particularly, in the ground layer of the paintings, below the colored layer. These observations imply that lead oxide, introduced as a siccative and not as a pigment, may be the element mainly responsible for the protrusions formation, and that this degradation may appear very rapidly on paintings. (orig.)

  20. Contact allergy to epoxy resin

    DEFF Research Database (Denmark)

    Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil

    2012-01-01

    Background. Epoxy resin monomers are strong skin sensitizers that are widely used in industrial sectors. In Denmark, the law stipulates that workers must undergo a course on safe handling of epoxy resins prior to occupational exposure, but the effectiveness of this initiative is largely unknown...... in an educational programme. Conclusion. The 1% prevalence of epoxy resin contact allergy is equivalent to reports from other countries. The high occurrence of epoxy resin exposure at work, and the limited use of protective measures, indicate that reinforcement of the law is required....

  1. A Spectroscopic Method for Determining Free Iodine in Iodinated Fatty-Acid Esters

    Science.gov (United States)

    Klyubin, V. V.; Klyubina, K. A.; Makovetskaya, K. N.

    2018-01-01

    It is shown that the concentration of free iodine in samples of iodinated fatty-acid esters can be measured using the electronic absorption spectra of their solutions in ethanol. The method proposed is rather simple in use and highly sensitive, allowing detection of presence of less than 10 ppm of free iodine in iodinated compounds. It is shown using the example of Lipiodol that this makes it possible to easily detect small amounts of free iodine in samples containing bound iodine in concentrations down to 40 wt %.

  2. Oil-based paint poisoning

    Science.gov (United States)

    Paint - oil-based - poisoning ... Hydrocarbons are the primary poisonous ingredient in oil paints. Some oil paints have heavy metals such as lead, mercury, cobalt, and barium added as pigment. These heavy metals can cause additional ...

  3. Process Waste Assessment - Paint Shop

    International Nuclear Information System (INIS)

    Phillips, N.M.

    1993-06-01

    This Process Waste Assessment was conducted to evaluate hazardous wastes generated in the Paint Shop, Building 913, Room 130. Special attention is given to waste streams generated by the spray painting process because it requires a number of steps for preparing, priming, and painting an object. Also, the spray paint booth covers the largest area in R-130. The largest and most costly waste stream to dispose of is open-quote Paint Shop wasteclose quotes -- a combination of paint cans, rags, sticks, filters, and paper containers. These items are compacted in 55-gallon drums and disposed of as solid hazardous waste. Recommendations are made for minimizing waste in the Paint Shop. Paint Shop personnel are very aware of the need to minimize hazardous wastes and are continuously looking for opportunities to do so

  4. Characterization of iodinated adrenomedullin derivatives suitable for lung nuclear medicine

    Energy Technology Data Exchange (ETDEWEB)

    Fu Yan; Letourneau, Myriam; Chatenet, David [Laboratoire d' etudes moleculaires et pharmacologiques des peptides, INRS-Institut Armand-Frappier, Ville de Laval, Qc, H7V 1B7 (Canada); Dupuis, Jocelyn [Research Center, Montreal Heart Institute, Montreal, Qc (Canada); Department of Medicine, University of Montreal, Montreal, Qc (Canada); Fournier, Alain, E-mail: alain.fournier@iaf.inrs.ca [Laboratoire d' etudes moleculaires et pharmacologiques des peptides, INRS-Institut Armand-Frappier, Ville de Laval, Qc, H7V 1B7 (Canada)

    2011-08-15

    Introduction: We have recently demonstrated the effectiveness of 99m-technetium adrenomedullin (AM) as a new molecular lung imaging agent that could provide significant advantages for the diagnosis and follow-up of disorders affecting the pulmonary circulation such as pulmonary embolism and pulmonary hypertension. Having the possibility to conjugate the targeting molecule with different radionuclides would offer more flexibility and potential advantages depending on clinical situations. Since various iodine isotopes are currently used in nuclear medicine and in pharmacological studies, we have evaluated which iodination method should be privileged in order to produce a good iodinated AM-derived nuclear medicine agent. Methods: Synthetic AM was labeled with iodine through chemical and lactoperoxidase oxidation methods. Position of the iodine atom on the peptide was determined by MALDI-TOF mass spectrometry analysis following cyanogen bromide cleavage and carboxypeptidase Y digestion. Binding affinity of iodinated AM analogues was evaluated by competition and saturation binding experiments on dog lung preparations. Results: In this study, we demonstrated that, upon lactoperoxidase oxidation, iodination occurred at Tyr{sup 1} and that this radioligand retained higher binding affinity and specificity over preparations obtained through chemical oxidation. Conclusions: These results emphasize the fact that even a small chemical modification, i.e. iodination, might deeply modify the pharmacological profile of a compound and support observations that the C-terminal tail of human AM plays an important role in the AM receptor binding process. Consequently, incorporation of a radionuclide to produce an AM-based nuclear medicine agent should privilege the N-terminus of the molecule.

  5. [Assessment of dietary iodine intake of population in non-high-iodine areas in China].

    Science.gov (United States)

    Song, Xiaoyu; Li, Fengqin; Liu, Zhaoping; He, Yuna; Sui, Haixia; Mao, Weifeng; Liu, Sana; Yan, Weixing; Li, Ning; Chen, Junshi

    2011-03-01

    To assess the potential risk of dietary iodine insufficiency of population in non-high-iodine areas (water iodine China. The dietary iodine intake of 13 age-sex population groups were estimated by combining the data of iodine intake from food, table salt and drinking water. Two conditions were considered: consuming iodized salt or non-iodized salt. The data of food and table salt consumption were derived from the Chinese National Nutrition and Health Survey in 2002. Water consumption was calculated as the recommended water intake. Iodine contents of food, table salt and water were calculated from China Food Composition Table and iodine surveillance data. Under the condition of consuming iodized salt, the average iodine intake of all population groups was higher than the Recommended Nutrient Intake (RNI), while the iodine intakes of individuals above Upper Limits (UL) and below RNI were 5.8% and 13.4% respectively, and the iodine intake of individuals lower than the Estimated Average Requirement (EAR) was 9.4% in adults above 18 years of age (including pregnant and lactating women). If non-iodized salt was consumed, the average iodine intake of most sex-age population groups was higher than RNI, but the iodine intake of 97.6% of individuals would be lower than RNI, while the iodine intake of 97.4% of adults would be lower than EAR. The contribution of iodine from table salt was much higher than that from drinking water and food in the condition of consuming iodized salt, while food was the predominant contributor of dietary iodine in the condition of consuming non-iodized salt. The health risk of iodine deficiency was higher than that of iodine excess in areas where water iodine was China, and the risk of iodine insufficiency was much higher if non-iodized salt was consumed. Iodized salt should be the main sources of dietary iodine intake for population in areas where water iodine was China.

  6. The iodine reactivity

    International Nuclear Information System (INIS)

    2003-01-01

    The iodine is an important element because it has long life isotopes (such as iodine 129) and a great mobility in natural media. Iodine presents a complex chemistry because of its volatility and its strong redox reactivity. The S.E.C.R. works to better understand the reactivity of this element in different natural, industrial or biological environments. It plays a part in thermochemical sites as a possible way of hydrogen formation. This seminar gives some aspects relative to the chemical reactivity of iodine, since its thermochemistry in the I/S cycles to produce hydrogen to its reactivity in the natural medium and its potential radiological impact. This document includes 4 presentations transparencies) dealing with: the 129 I cycle rejected in the low radioactive gaseous and liquid effluents of the La Hague reprocessing plant (C. Frechou); a bibliographic review of iodine retention in soils (F. Bazer-Bachi); the hydrogen production and the iodine/sulfur thermochemical cycle (role of iodine in the process); and the direct characterization by electro-spray ionization mass spectroscopy of iodine fixation by fulvic acids (P. Reiller, B. Amekraz, C. Moulin, V. Moulin)

  7. Povidone-iodine induced post-surgical irritant contact dermatitis localized outside of the surgical incision area. Report of 27 cases and a literature review.

    Science.gov (United States)

    Borrego, Leopoldo; Hernández, Noelia; Hernández, Zaida; Peñate, Yeray

    2016-05-01

    Povidone-iodine solution is an antiseptic that is used worldwide as surgical paint and is considered to have a low irritant potential. Post-surgical severe irritant dermatitis has been described after the misuse of this antiseptic in the surgical setting. Between January 2011 and June 2013, 27 consecutive patients with post-surgical contact dermatitis localized outside of the surgical incision area were evaluated. Thirteen patients were also available for patch testing. All patients developed dermatitis the day after the surgical procedure. Povidone-iodine solution was the only liquid in contact with the skin of our patients. Most typical lesions were distributed in a double lumbar parallel pattern, but they were also found in a random pattern or in areas where a protective pad or an occlusive medical device was glued to the skin. The patch test results with povidone-iodine were negative. Povidone-iodine-induced post-surgical dermatitis may be a severe complication after prolonged surgical procedures. As stated in the literature and based on the observation that povidone-iodine-induced contact irritant dermatitis occurred in areas of pooling or occlusion, we speculate that povidone-iodine together with occlusion were the causes of the dermatitis epidemic that occurred in our surgical setting. Povidone-iodine dermatitis is a problem that is easily preventable through the implementation of minimal routine changes to adequately dry the solution in contact with the skin. © 2015 The International Society of Dermatology.

  8. Interfacially enhancement of PBO/epoxy composites by grafting MWCNTs onto PBO surface through melamine as molecular bridge

    Science.gov (United States)

    Lv, Junwei; Wang, Bin; Ma, Qi; Wang, Wenjing; Xiang, Dong; Li, Mengyao; Zeng, Lan; Li, Hui; Li, Yuntao; Zhao, Chunxia

    2018-06-01

    Melamine and multi-walled carbon nanotubes (MWCNTs) were grafted onto Poly-p-phenylene benzobisoxazole (PBO) fiber surface effectively via layer-by-layer method. Both of them have been chemically bonded as fourier transform infrared spectroscopy (FTIR) confirmed. Grafting melamine overcame the inertness of PBO surface. Ammoniation was processed on PBO surface through grafting melamine so that the MWCNTs could be grafted onto PBO surface. Scanning electron microscopy (SEM) images indicated that melamine used as molecular bridge could increase MWCNTs’ quantity on PBO surface. X-ray photoelectron spectroscopy (XPS) results revealed the variation of chemical composition of PBO surface. Test of interfacial shear strength (IFSS) and tensile strength indicated the great mechanical properties of modified PBO fibers when combining with epoxy resin. Furthermore, whole reaction was processed under a simple condition. Results in this research also promised a potential method to modify PBO surface.

  9. Iodine intake in Denmark

    International Nuclear Information System (INIS)

    Pedersen, K.M.; Noehr, S.B.; Laurberg, P.

    1997-01-01

    Iodine deficiency with a high frequency of goitre and, in severely affected areas, cretinism is common in some areas of the world. In Denmark the iodine intake as evaluated by urinary iodine excretion has been at a stable low level for many years, except for the part of the population now taking iodine supplementation as part of vitamin/mineral preparations. The iodine intake is lowest in the western part to the country where an epidemiological study of elderly subjects has demonstrated a high frequency of goitre and hyperthyroidism in women. This supports the suggestion of a controlled moderate increase in iodine intake via an iodine supplementation program. (au) 40 refs

  10. CFD Analyses of Re-Evolved Iodine from an In-containment Water Pool

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Tae Hyeon [KHNP CRI, Daejeon (Korea, Republic of); Yoon, Woo Sung; Jung, Ji Hwan [Pusan National University, Busan (Korea, Republic of)

    2016-10-15

    A good understanding of the behavior of iodine is required to evaluate the safety and emergency procedures after a LOCA. The quantity of re-evolved iodine is related to pH level, temperature, and iodine concentration of water pool. In the calculation of pH for water pool, sequence calculations must consider this variable if any aqueous iodine is present, even if it is initially present in stable forms. The present study consists of two parts: the pH evaluation and the evaluation of the iodine re-evolution. The current paper focuses on the pH evaluation method, the development of a user-defined function (UDF) and the iodine re-evolution from the water pool. CFD that incorporates the UDF was used in this study to calculate the local pH level in the transient condition. The amount of re-evolved iodine was calculated based on the iodine concentration, temperature, and pH. The transportation and resulting distribution of the iodine concentration, temperature, and pH were calculated using transient analyses with CFD. The quantity of reevolved iodine was obtained with several assumptions. The quantitative evaluation of re-evolved iodine during a LOCA in a commercial nuclear power plants is done in two stages. The first stage is to calculate the pH in the water pool, and the second stage is to calculate the quantity of re-evolved iodine. Evaporated iodine, from the water pool water to the containment atmosphere, can be estimated from characteristic iodine behaviors and pH calculations. The 3D CFD analysis results show that the pH reached 7.0 after 149.5 minutes. Near the spillway, the change in averaged pH was faster than the change in wholevolume averaged pH. Evaluating the amount of reevolved iodine were examined using four different methods. As a result of our evaluation of iodine reevolution, the initial molecular iodine concentration of a water pool has a significant impact on the amount of gaseous iodine, more so than the pH or temperature, due to the locally similar

  11. CFD Analyses of Re-Evolved Iodine from an In-containment Water Pool

    International Nuclear Information System (INIS)

    Kim, Tae Hyeon; Yoon, Woo Sung; Jung, Ji Hwan

    2016-01-01

    A good understanding of the behavior of iodine is required to evaluate the safety and emergency procedures after a LOCA. The quantity of re-evolved iodine is related to pH level, temperature, and iodine concentration of water pool. In the calculation of pH for water pool, sequence calculations must consider this variable if any aqueous iodine is present, even if it is initially present in stable forms. The present study consists of two parts: the pH evaluation and the evaluation of the iodine re-evolution. The current paper focuses on the pH evaluation method, the development of a user-defined function (UDF) and the iodine re-evolution from the water pool. CFD that incorporates the UDF was used in this study to calculate the local pH level in the transient condition. The amount of re-evolved iodine was calculated based on the iodine concentration, temperature, and pH. The transportation and resulting distribution of the iodine concentration, temperature, and pH were calculated using transient analyses with CFD. The quantity of reevolved iodine was obtained with several assumptions. The quantitative evaluation of re-evolved iodine during a LOCA in a commercial nuclear power plants is done in two stages. The first stage is to calculate the pH in the water pool, and the second stage is to calculate the quantity of re-evolved iodine. Evaporated iodine, from the water pool water to the containment atmosphere, can be estimated from characteristic iodine behaviors and pH calculations. The 3D CFD analysis results show that the pH reached 7.0 after 149.5 minutes. Near the spillway, the change in averaged pH was faster than the change in wholevolume averaged pH. Evaluating the amount of reevolved iodine were examined using four different methods. As a result of our evaluation of iodine reevolution, the initial molecular iodine concentration of a water pool has a significant impact on the amount of gaseous iodine, more so than the pH or temperature, due to the locally similar

  12. Radiation-polymerisable paint and its applications

    International Nuclear Information System (INIS)

    Cassata, J.C.; Dickie, R.A.

    1974-01-01

    A paint polymerisable under the effect of a radiation is presented. The main components, excluding non-polymerisable solvent, pigment, initiator and particle charge, are as follows: about 90 to 10 parts of a saturated thermoplastic vinyl polymer of average molecular mass around 2000 to 250,000, prepared from monofunctional vinyl monomers to the extent of at least 85% by weight; about 10 to 90 parts of vinyl monomer solvent for the polymer, up to 90% by weight of the solvent consisting of monovinyl monomers and the remainder being chosen amongst divinyl, trivinyl, tetravinyl monomers and their mixtures. The average molecular weight of the thermoplastic vinyl polymer has between 5000 and 50,000 [fr

  13. Iodinated bleomycin

    International Nuclear Information System (INIS)

    Lunghi, F.; Riva, P.; Assone, F.; Villa, M.; Plassic, G.

    1978-01-01

    Bleomycin was labelled with iodine-131 by the iodine monochloride method. Iodination did not alter the chemical and chromatographic features and ''in vitro'' stability studies on freeze-dried 131 I-Bleomycin having a specific activity of 1 mCi/mg, stored at different temperatures, showed no appreciable variation of the free-iodine content. Tissue distribution of 131 I-Bleomycin has been evaluated in tumor bearing rats. Patients have been injected with 0.5-1.0 mCi of 131 I-Bleomycin corresponding to a maximum of 1.5 mg. No adverse reactions have been observed. Total body scans have been performed at 2, 6, 24 and 48 hours after injection. The iodinated Bleomycin was rapidly distributed and cleared from the body and showed an early uptake in the neoplastic tissue. A diagnostic accuracy of 90% has been observed in malignant deseases, while no false positive results have been, at the moment, recorded. (author)

  14. X-ray photoelectron and Auger electron spectroscopic study of the adsorption of molecular iodine on uranium metal and uranium dioxide

    International Nuclear Information System (INIS)

    Dillard, J.G.; Moers, H.; Klewe-Nebenius, H.; Kirch, G.; Pfennig, G.; Ache, H.J.

    1984-01-01

    The adsorption of molecular iodine on uranium metal and on uranium dioxide has been investigated at 25 0 C. Clean surfaces were prepared in an ultrahigh vacuum apparatus and were characterized by X-ray photoelectron (XPS) and X-ray and electron-induced Auger electron spectroscopies (AES). Adsorption of I 2 was studied for exposures up to 100 langmuirs (1 langmuir = 10 -6 torr s) on uranium metal and to 75 langmuirs on uranium dioxide. Above about 2-langmuir I 2 exposure on uranium, spectroscopic evidence is obtained to indicate the beginning of UI 3 formation. Saturation coverage for I 2 adsorption on uranium dioxide occurs at approximately 10-15 langmuirs. Analysis of the XPS and AES results as well as studies of spectra as a function of temperature lead to the conclusions that a dissociative chemisorption/reaction process occurs on uranium metal while nondissociative adsorption occurs on uranium dioxide. Variations in the iodine Auger kinetic energy and in the Auger parameter are interpreted in light of extra-atomic relaxation processes. 42 references, 10 figures, 1 table

  15. Urinary Iodine Concentrations Indicate Iodine Deficiency in Pregnant Thai Women but Iodine Sufficiency in Their School-Aged Children

    NARCIS (Netherlands)

    Gowachirapant, S.; Winichagoon, P.; Wyss, L.; Tong, B.; Baumgartner, J.; Boonstra, A.; Zimmermann, M.B.

    2009-01-01

    The median urinary iodine concentration (UI) in school-aged children is recommended for assessment of iodine nutrition in populations. If the median UI is adequate in school-aged children, it is usually assumed iodine intakes are also adequate in the remaining population, including pregnant women.

  16. Field measurements of the washout coefficient for gaseous iodine likely to be released on accidental conditions

    International Nuclear Information System (INIS)

    Caput, C.; Camus, H.; Gauthier, D.; Belot, Y.

    1992-01-01

    Field experiments were performed in Brittany to assess the washout coefficient Λ for molecular iodine. During each run, a few grams of nonradioactive iodine were released from a 12 meters telescopic mast, and the rain was sampled at a short distance downwind along complete transversal sections of the plume. The amount of iodine in each sample was determined by ionic chromatography to calculate the washout coefficient. In most cases, the results obtained (a few 10 -5 s -1 ) are not so different as expected from the theoretical values assuming a complete solubility of iodine in rain water. 4 refs., 1 fig., 1 tab

  17. Selective paint coatings for coloured solar absorbers: Polyurethane thickness insensitive spectrally selective (TISS) paints (Part II)

    Energy Technology Data Exchange (ETDEWEB)

    Orel, B.; Spreizer, H.; Surca Vuk, A.; Fir, M. [National Institute of Chemistry, Hajdrihova 19, SI-1000 Ljubljana (Slovenia); Merlini, D.; Vodlan, M. [Color d.d., Cesta komandanta Staneta 4, SI-1230 Medvode (Slovenia); Koehl, M. [Fraunhofer-Institute for Solar Energy Systems ISE, Heidenhofstr. 2, D-79110 Freiburg (Germany)

    2007-01-23

    Red, green and blue paints were prepared for use as thickness insensitive spectrally selective (TISS) paint coatings for solar facade absorbers. The paints were composed of a polyurethane resin binder in which various pigments were incorporated in such a way that they formed stable paint dispersions, satisfying stability criteria for facade coatings. A low emittance of the paints was achieved by using low-emittance aluminium flake pigments combined with iron oxide (red coloured paints). Black pigment was added to adjust solar absorptance. Blue and green paints were made by the addition of coloured aluminium flake pigment and the solar absorptance was also adjusted by the addition of black pigment. Efficiency for photo-thermal conversion of solar radiation was assessed by evaluation of the corresponding performance criteria, which enabled the selection of paints whose performance criteria values were higher than 0 (spectrally non-selective black coating). The results confirmed that blue and green paints and to minor extent red ones, combined selectivity with colour. The morphology of the paints was assessed, revealing that the colours originated from the deposition of finely dispersed colour and/or black pigment on the surface of the aluminium flakes during paint preparation. (author)

  18. The influence of physical parameters on the adsorption of iodine 131 by activated charcoals

    International Nuclear Information System (INIS)

    Billard, F.; Chevalier, G.; Caron, J.; Van Der Meersch, J.

    1966-01-01

    Following an outline of the means of generating iodine 131 in the gas phase and a brief description of the apparatus used, the authors analyse the experimental results obtained on the trapping of iodine 131 by activated charcoal. The efficiency depends concurrently on the relative humidity and the iodine concentration of the air. While it is independent of this concentration in dry air, it does not exceed 50 in moist air, whatever the bed depth, when the concentration is less than 1 mCi/m 3 , then it increases with the concentrations to reach values close to those obtained in dry air for concentrations of around 1000 Ci/m 3 . At the same time the efficiency of a dust filter with respect to iodine remains very low in dry air whatever the iodine concentration; in moist air this efficiency, which is high at low concentrations, decreases when the latter increases. In addition if a charcoal bed is divided into several beds, separated by an amount corresponding to a passage time of about a second, it is found that the efficiency of the whole is appreciably higher than that of the initial bed. These results appear to establish the existence of at least two forms of iodine, one molecular form and one particulate form probably formed by clusters, the forms equilibrium being functions of the relative concentrations of iodine and water vapour in the air. The third form evidence, a gaseous form compound, remains hypothetical; the experimental curves can be explained either by the molecular and particular forms reversibility or by the increase of clusters size with the relative humidity of the air. (authors) [fr

  19. Novel molecular-level evidence of iodine binding to natural organic matter from Fourier transform ion cyclotron resonance mass spectrometry

    International Nuclear Information System (INIS)

    Xu, Chen; Chen, Hongmei; Sugiyama, Yuko; Zhang, Saijin; Li, Hsiu-Ping; Ho, Yi-Fang; Chuang, Chia-ying; Schwehr, Kathleen A.; Kaplan, Daniel I.; Yeager, Chris; Roberts, Kimberly A.; Hatcher, Patrick G.; Santschi, Peter H.

    2013-01-01

    Major fractions of radioiodine ( 129 I) are associated with natural organic matter (NOM) in the groundwater and surface soils of the Savannah River Site (SRS). Electrospray ionization coupled to Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICR-MS) was applied to elucidate the interactions between inorganic iodine species (iodide and iodate) and a fulvic acid (FA) extracted from a SRS surface soil. Iodate is likely reduced to reactive iodine species by the lignin- and tannin-like compounds or the carboxylic-rich alicyclic molecules (CRAM), during which condensed aromatics and lignin-like compounds were generated. Iodide is catalytically oxidized into reactive iodine species by peroxides, while FA is oxidized by peroxides into more aliphatic and less aromatic compounds. Only 9% of the total identified organo-iodine compounds derived from molecules originally present in the FA, whereas most were iodine binding to newly-produced compounds. The resulting iodinated molecules were distributed in three regions in the van Krevelen diagrams, denoting unsaturated hydrocarbons, lignin and protein. Moreover, characteristics of these organo-iodine compounds, such as their relatively low O/C ratios ( 2 or -HNCOR groups and a ring-activating functionality to favor the electrophilic substitution. The ESI-FTICR-MS technique provides novel evidence to better understand the reactivity and scavenging properties of NOM towards radioiodine and possible influence of NOM on 129 I migration. Highlights: ► IO 3 − reduced by lignin-, tannin-like compounds/carboxylic-rich alicyclic molecules ► Condensed aromatic and lignin-like compounds generated after iodate-iodination ► Aliphatic and less aromatic compounds formed after iodide-iodination ► Organo-iodine identified as unsaturated hydrocarbons, lignin and protein ► Organo-iodine with low O/C ratios imply less environmental mobility

  20. Epoxy-based carbon nanotubes reinforced composites

    CSIR Research Space (South Africa)

    Kesavan Pillai, Sreejarani

    2011-04-01

    Full Text Available of the three major epoxy resin producers worldwide [May, 1987]. Epoxy resin is most commonly used as a matrix for advanced composites due to their superior thermal, mechanical and electrical properties; dimensional stability and chemical resistance. Epoxy... are electrical insulators, and the widespread use of the epoxy resins for many high-performance applications is constrained because of their inherent brittleness, delamination and fracture toughness limitations. There were quite a few approaches to enhance...

  1. Novel molecular-level evidence of iodine binding to natural organic matter from Fourier transform ion cyclotron resonance mass spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Chen, E-mail: xuchen66@tamu.edu [Laboratory for Environmental and Oceanographic Research, Department of Marine Sciences, Texas A and M University, Building 3029, Galveston, TX 77551 (United States); Chen, Hongmei [Department of Chemistry and Biochemistry, Old Dominion University, Norfolk, VA 23529 (United States); Sugiyama, Yuko [Department of Chemistry and Biochemistry, Old Dominion University, Norfolk, VA 23529 (United States); University of Hyogo, 1-1-12, Shinzaike-honcho, Himeji, Hyogo 670-0092 (Japan); Zhang, Saijin; Li, Hsiu-Ping; Ho, Yi-Fang; Chuang, Chia-ying; Schwehr, Kathleen A. [Laboratory for Environmental and Oceanographic Research, Department of Marine Sciences, Texas A and M University, Building 3029, Galveston, TX 77551 (United States); Kaplan, Daniel I. [Savannah River National Laboratory, Aiken, SC 29808 (United States); Yeager, Chris [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Roberts, Kimberly A. [Savannah River National Laboratory, Aiken, SC 29808 (United States); Hatcher, Patrick G. [Department of Chemistry and Biochemistry, Old Dominion University, Norfolk, VA 23529 (United States); Santschi, Peter H. [Laboratory for Environmental and Oceanographic Research, Department of Marine Sciences, Texas A and M University, Building 3029, Galveston, TX 77551 (United States)

    2013-04-01

    Major fractions of radioiodine ({sup 129}I) are associated with natural organic matter (NOM) in the groundwater and surface soils of the Savannah River Site (SRS). Electrospray ionization coupled to Fourier transform ion cyclotron resonance mass spectrometry (ESI-FTICR-MS) was applied to elucidate the interactions between inorganic iodine species (iodide and iodate) and a fulvic acid (FA) extracted from a SRS surface soil. Iodate is likely reduced to reactive iodine species by the lignin- and tannin-like compounds or the carboxylic-rich alicyclic molecules (CRAM), during which condensed aromatics and lignin-like compounds were generated. Iodide is catalytically oxidized into reactive iodine species by peroxides, while FA is oxidized by peroxides into more aliphatic and less aromatic compounds. Only 9% of the total identified organo-iodine compounds derived from molecules originally present in the FA, whereas most were iodine binding to newly-produced compounds. The resulting iodinated molecules were distributed in three regions in the van Krevelen diagrams, denoting unsaturated hydrocarbons, lignin and protein. Moreover, characteristics of these organo-iodine compounds, such as their relatively low O/C ratios (< 0.2 or < 0.4) and yet some degree of un-saturation close to that of lignin, have multiple important environmental implications concerning possibly less sterically-hindered aromatic ring system for iodine to get access to and a lower hydrophilicity of the molecules thus to retard their migration in the natural aquatic systems. Lastly, ∼ 69% of the identified organo-iodine species contains nitrogen, which is presumably present as -NH{sub 2} or -HNCOR groups and a ring-activating functionality to favor the electrophilic substitution. The ESI-FTICR-MS technique provides novel evidence to better understand the reactivity and scavenging properties of NOM towards radioiodine and possible influence of NOM on {sup 129}I migration. Highlights: ► IO{sub 3}{sup

  2. Physical properties of a high molecular weight hydroxyl-terminated polydimethylsiloxane modified castor oil based polyurethane/epoxy interpenetrating polymer network composites

    Science.gov (United States)

    Chen, Shoubing; Wang, Qihua; Wang, Tingmei

    2011-06-01

    A series of polyurethane (PU)/epoxy resin (EP) graft interpenetrating polymer network (IPN) composites modified by a high molecular weight hydroxyl-terminated polydimethylsiloxane (HTPDMS) were prepared. The effects of HTPDMS content on the phase structure, damping properties and the glass transition temperature ( Tg) of the HTPDMS-modified PU/EP IPN composites were studied by scanning electron microscopy (SEM) and dynamic mechanical analysis (DMA). Thermogravimetric analysis (TGA) showed that the thermal decomposition temperature of the composites increased with the increase of HTPDMS content. The tensile strength and impact strength of the IPN composites were also significantly improved, especially when the HTPDMS content was 10%. The modified IPN composites were expected to be used as structural damping materials in the future.

  3. Development of analytical methods for iodine speciation in fresh water

    International Nuclear Information System (INIS)

    Takaku, Yuichi; Ohtsuka, Yoshihito; Hisamatsu, Shun'ichi

    2007-01-01

    Analytical methods for physicochemical speciation of iodine in fresh water samples were developed to elucidate its behavior in the environment. The methods combined inductively coupled plasma mass spectrometry (ICP-MS) with size exclusion high performance liquid chromatography (SEC) or capillary electrophoresis (CE). Freshwater samples were collected from Lake Towada and rivers surrounding the lake. After filtration through a 0.45 μm pore size membrane filter, iodine in the water samples was pre-concentrated with an ultra-filtration filter which had a cut-off size of 10 kDa. The fraction with molecular size over 10 kDa was concentrated to 100 times in the original water, and then introduced into the SEC-ICP-MS. Molecular size chromatograms of all river and lake water samples showed two peaks for iodine concentrations: 40 kDa and 20 kDa. The method for separately determining two valence states of inorganic iodine, I - and IO 3 - , was also developed using the CE-ICP-MS system and it was successfully applied to the fresh water samples. Analysis results of surface water samples in Lake Towada and rivers surrounding the lake indicated that the chemical form of inorganic iodine in all samples was IO 3 - . Additional lake water samples were collected from Lake O-ike-higashi in the Juni-ko area at Shirakami-Sanchi, which is a UNESCO natural world heritage. The lake has a strong thermocline during all seasons; its bottom layer is in a highly reductive state. Depth profiles of I - and IO 3 - clearly showed that I - was not detected in the surface layer, but it was predominant in the bottom layer, and vice versa for IO 3 - . As this separation method is rapid and sensitive, it will be widely used in the future. (author)

  4. Iodine generator for reclaimed water purification

    Science.gov (United States)

    Wynveen, R. A.; Powell, J. D.; Schubert, F. H. (Inventor)

    1977-01-01

    The system disclosed is for controlling the iodine level in a water supply in a spacecraft. It includes an iodine accumulator which stores crystalline iodine, an electrochemical valve to control the input of iodine to the drinking water and an iodine dispenser. A pump dispenses fluid through the iodine dispenser and an iodine sensor to a potable water tank storage. The iodine sensor electronically detects the iodine level in the water, and through electronic means, produces a correction current control. The correction current control operates the electro-chemical iodine valve to release iodine from the iodine accumulator into the iodine dispenser.

  5. Iodination of the humic samples from HUPA project

    International Nuclear Information System (INIS)

    Reiller, P.; Mercier-Bion, F.; Barre, N.; Gimenez, N.; Miserque, F.

    2005-01-01

    The interaction of iodine with natural organic matter in general and with humic substances (HS) in particular, has been the subject of numerous studies. It has come to a consensus that in soils as well as in aquatic systems, the speciation of iodine is closely related to the redox potential of the medium. In oxidizing media, as in sea water or upper horizons, the major part of iodine is found in iodate form IO 3 - , whereas in reducing media, iodide I - is the major specie. Nevertheless, it has been shown that in some cases, organically bound iodine can dominate the speciation either as methyl iodide or bounded to humic substances. It is now also clear that this reactivity is closely related to the occurrence of molecular iodine I 2 (aq) and its disproportionation to HIO and I - . The reaction scheme can be viewed as an electrophilic substitution of an hydrogen to an iodine atom on a phenolic ring. This scheme has been validated in the case of HS on different samples including HUPA, and the covalent character of this interaction has been shown using electrospray ionization mass spectroscopy (ESI-MS), X-ray photoelectron spectroscopy. Nevertheless, in some of the latter studies, the characterization of the final reaction products did not satisfy the authors completely as total separation from I - could not be achieved. Thus, further studies were led using HUPA samples: natural humic and fulvic extract from Gorleben and synthetic samples obtained form FZ Rossendorf. Dialysis procedures were envisaged to improve the incomplete separation between the colloidal humic matter and the iodide ions either unreacted or produced by the reaction. (orig.)

  6. Performance of paint coatings in the radiation fields of nuclear reactors and of high energy particle accelerators and after contamination by radionuclides

    CERN Document Server

    Schönbacher, Helmut; Oesterle, K M; Van de Voorde, M

    1977-01-01

    Several commercially available two/component coating systems based on epoxy and polyurethane resin, as well as lithium silicate/zinc dust paint coatings, have been irradiated in a nuclear reactor up to a dose of 2*10/sup 9/ rad and in a 28 GeV proton accelerator up to a dose of 1*10/sup 9/ rad. Besides assessment by visual inspection, the irradiated specimens have been subjected to the impact hardness test, the infinitesimal hardness behaviour tests, the grid scarification test and to swelling tests in methanol and acetone. The decontaminability of these paint coatings after contamination with solutions containing Ca 45, S 35 and I 131 is also investigated. Very good results in respect of decontaminability and radiation resistance up to 1*10/sup 9/ rad have been obtained with a coating of polyurethane cross-linked with an aliphatic diisocyanate. (9 refs).

  7. Thermally activated, single component epoxy systems

    KAUST Repository

    Unruh, David A.; Pastine, Stefan J.; Moreton, Jessica C.; Frechet, Jean

    2011-01-01

    A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

  8. Thermally activated, single component epoxy systems

    KAUST Repository

    Unruh, David A.

    2011-08-23

    A single component epoxy system in which the resin and hardener components found in many two-component epoxies are combined onto the same molecule is described. The single molecule precursor to the epoxy resin contains both multiple epoxide moieties and a diamine held latent by thermally degradable carbamate linkages. These bis-carbamate "single molecule epoxies" have an essentially infinite shelf life and access a significant range in curing temperatures related to the structure of the carbamate linkages used. © 2011 American Chemical Society.

  9. Iodination and stability of somatostatin analogues: comparison of iodination techniques. A practical overview.

    Science.gov (United States)

    de Blois, Erik; Chan, Ho Sze; Breeman, Wouter A P

    2012-01-01

    For iodination ((125/127)I) of tyrosine-containing peptides, chloramin-T, Pre-Coated Iodo-Gen(®) tubes and Iodo-Beads(®) (Pierce) are commonly used for in vitro radioligand investigations and there have been reliant vendors hereof for decades. However, commercial availability of these radio-iodinated peptides is decreasing. For continuation of our research in this field we investigated and optimized (radio-)iodination of somatostatin analogues. In literature, radioiodination using here described somatostatin analogues and iodination techniques are described separately. Here we present an overview, including High Performance Liquid Chromatography (HPLC) separation and characterisation by mass spectrometry, to obtain mono- and di-iodinated analogues. Reaction kinetics of (125/127)I iodinated somatostatin analogues were investigated as function of reaction time and concentration of reactants, including somatostatin analogues, iodine and oxidizing agent. To our knowledge, for the here described somatostatin analogues, no (127)I iodination and optimization are described. (Radio-)iodinated somatostatin analogues could be preserved with a >90% radiochemical purity for 1 month after reversed phase HPLC-purification.

  10. Microscale radiocarbon dating of paintings

    International Nuclear Information System (INIS)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron; Kueffner, Markus; Ferreira, Ester S.B.; Scherrer, Nadim C.

    2016-01-01

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. 14 C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the 14 C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated. (orig.)

  11. Microscale radiocarbon dating of paintings

    Energy Technology Data Exchange (ETDEWEB)

    Hendriks, Laura; Hajdas, Irka; McIntyre, Cameron [ETH Zurich, Ion Beam Physics, Zurich (Switzerland); Kueffner, Markus; Ferreira, Ester S.B. [SIK-ISEA, Zurich, Zurich (Switzerland); Scherrer, Nadim C. [Bern University of Applied Sciences, HKB, Bern (Switzerland)

    2016-03-15

    In this paper, radiocarbon dating of paintings using minimal sample sizes has been investigated, in an effort to address the problem of limited access to sample material in paintings. {sup 14}C analyses were conducted on signed and dated paintings from two Swiss artists of the twentieth century. The selected paintings dated from the 1930s and 1960s, provided the opportunity to evaluate the dating accuracy on paintings realized before and after 1950 AD when the {sup 14}C bomb peak was created, as a result of the nuclear tests conducted in the 1950/1960s. The work focused on the one hand on minimizing the size of the canvas sample required for accelerator mass spectrometer radiocarbon measurement on the gas ion source of the MICADAS and, on the other hand, on testing the possibility of dating the organic binder of the paint. Following careful characterization of the paint composition by X-ray fluorescence spectroscopy, Fourier transformed infrared spectroscopy, and Raman spectroscopy, paints containing no other carbon source than the natural organic binder were identified and dated. (orig.)

  12. Chemical species of iodine in some seaweeds. Pt. 2. Iodine-bound biological macromolecules

    International Nuclear Information System (INIS)

    Xiaolin Hou; Chifang Chai; Xiaojun Yan

    2000-01-01

    The distribution of iodine in various biological macromolecules in Sargassum kjellmanianum was studied using neutron activation analysis combined with chemical and biochemical separation techniques. The results indicate that iodine is mainly bound with protein, part of iodine with pigment and polyphenol, and little with polysaccharides, such as algin, fucoidan and cellulose. This result is significant for the mechanism of enriching iodine of algae and utilization of alga iodine. (author)

  13. Emydid herpesvirus 1 infection in northern map turtles (Graptemys geographica) and painted turtles (Chrysemys picta).

    Science.gov (United States)

    Ossiboff, Robert J; Newton, Alisa L; Seimon, Tracie A; Moore, Robert P; McAloose, Denise

    2015-05-01

    A captive, juvenile, female northern map turtle (Graptemys geographica) was found dead following a brief period of weakness and nasal discharge. Postmortem examination identified pneumonia with necrosis and numerous epithelial, intranuclear viral inclusion bodies, consistent with herpesviral pneumonia. Similar intranuclear inclusions were also associated with foci of hepatocellular and splenic necrosis. Polymerase chain reaction (PCR) screening of fresh, frozen liver for the herpesviral DNA-dependent DNA polymerase gene yielded an amplicon with 99.2% similarity to recently described emydid herpesvirus 1 (EmyHV-1). Molecular screening of turtles housed in enclosures that shared a common circulation system with the affected map turtle identified 4 asymptomatic, EmyHV-1 PCR-positive painted turtles (Chrysemys picta) and 1 asymptomatic northern map turtle. Herpesvirus transmission between painted and map turtles has been previously suggested, and our report provides the molecular characterization of a herpesvirus in asymptomatic painted turtles that can cause fatal herpesvirus-associated disease in northern map turtles. © 2015 The Author(s).

  14. Solving the problem of building models of crosslinked polymers: an example focussing on validation of the properties of crosslinked epoxy resins.

    Science.gov (United States)

    Hall, Stephen A; Howlin, Brendan J; Hamerton, Ian; Baidak, Alex; Billaud, Claude; Ward, Steven

    2012-01-01

    The construction of molecular models of crosslinked polymers is an area of some difficulty and considerable interest. We report here a new method of constructing these models and validate the method by modelling three epoxy systems based on the epoxy monomers bisphenol F diglycidyl ether (BFDGE) and triglycidyl-p-amino phenol (TGAP) with the curing agent diamino diphenyl sulphone (DDS). The main emphasis of the work concerns the improvement of the techniques for the molecular simulation of these epoxies and specific attention is paid towards model construction techniques, including automated model building and prediction of glass transition temperatures (T(g)). Typical models comprise some 4200-4600 atoms (ca. 120-130 monomers). In a parallel empirical study, these systems have been cast, cured and analysed by dynamic mechanical thermal analysis (DMTA) to measure T(g). Results for the three epoxy systems yield good agreement with experimental T(g) ranges of 200-220°C, 270-285°C and 285-290°C with corresponding simulated ranges of 210-230°C, 250-300°C, and 250-300°C respectively.

  15. Separation of iodine-131 from water using isotopic exchange with iodine-starch compound

    International Nuclear Information System (INIS)

    Ignatov, V.P.; Kolomejtseva, I.V.

    1990-01-01

    Conditions of iodine isotopic exchange with iodine-starch compound (ISC) were studied with the aim of compound utilizatoin for radioactive iodine separation from solution. It is shown that in pH range from 2 to 7 the degree of iodine extraction and coefficient of its distribution practically do not depend on pH, at pH>7 ISC destruction (decolorizing) starts and iodine extraction decreases. Rapid method of iodine separation from solution is suggested. The method can be used in radiochemical techniques. The degree of extraction equals 80 %, a higher degree of extraction can not be achieved owing to ISC formation peculiarities

  16. Iodine frequency references for space

    International Nuclear Information System (INIS)

    Schuldt, Thilo; Braxmaier, Claus; Döringshoff, Klaus; Peters, Achim; Oswald, Markus; Johann, Ulrich

    2017-01-01

    Optical frequency references are a key element for the realization of future space missions. They are needed for missions related to tests of fundamental physics, gravitational wave detection, Earth observation and navigation and ranging. In missions such as GRACE follow-on or LISA the optical frequency reference is used as light source for high-sensitivity inter-satellite distance metrology. While cavity-based systems are current baseline e.g. for LISA, frequency stabilization on a hyperfine transition in molecular iodine near 532 nm is a promising alternative. Due to its absolute frequency, iodine standards crucially simplify the initial spacecraft acquisition procedures. Current setups fulfill the GRACE-FO and LISA frequency stability requirements and are realized near Engineering Model level. We present the current status of our developments on Elegant Breadboard (EBB) and Engineering Model (EM) level taking into account specific design criteria for space compatibility such as compactness (size iodine spectroscopy EM: 38 × 18 × 10 cm 3 ) and robustness. Both setups achieved similar frequency stabilities of ∼ 1 · 10 −14 at an integration time of 1 s and below 5 · 10 −15 at integration times between 10 s and 1000 s. Furthermore, we present an even more compact design currently developed for a sounding rocket mission with launch in 2017. (paper)

  17. Iodine budget in surface waters from Atacama: Natural and anthropogenic iodine sources revealed by halogen geochemistry and iodine-129 isotopes

    International Nuclear Information System (INIS)

    Álvarez, Fernanda; Reich, Martin; Snyder, Glen; Pérez-Fodich, Alida; Muramatsu, Yasuyuki; Daniele, Linda; Fehn, Udo

    2016-01-01

    Iodine enrichment in the Atacama Desert of northern Chile is widespread and varies significantly between reservoirs, including nitrate-rich “caliche” soils, supergene Cu deposits and marine sedimentary rocks. Recent studies have suggested that groundwater has played a key role in the remobilization, transport and deposition of iodine in Atacama over scales of millions-of-years. However, and considering that natural waters are also anomalously enriched in iodine in the region, the relative source contributions of iodine in the waters and its extent of mixing remain unconstrained. In this study we provide new halogen data and isotopic ratios of iodine ("1"2"9I/I) in shallow seawater, rivers, salt lakes, cold and thermal spring water, rainwater and groundwater that help to constrain the relative influence of meteoric, marine and crustal sources in the Atacama waters. Iodine concentrations in surface and ground waters range between 0.35 μM and 26 μM in the Tarapacá region and between 0.25 μM and 48 μM in the Antofagasta region, and show strong enrichment when compared with seawater concentrations (I = ∼0.4 μM). In contrast, no bromine enrichment is detected (1.3–45.7 μM for Tarapacá and 1.7–87.4 μM for Antofagasta) relative to seawater (Br = ∼600 μM). These data, coupled to the high I/Cl and low Br/Cl ratios are indicative of an organic-rich sedimentary source (related with an “initial” fluid) that interacted with meteoric water to produce a mixed fluid, and preclude an exclusively seawater origin for iodine in Atacama natural waters. Iodine isotopic ratios ("1"2"9I/I) are consistent with halogen chemistry and confirm that most of the iodine present in natural waters derives from a deep initial fluid source (i.e., groundwater which has interacted with Jurassic marine basement), with variable influence of at least one atmospheric or meteoric source. Samples with the lowest isotopic ratios ("1"2"9I/I from ∼215 to ∼1000 × 10"

  18. Iodine mineral waters

    Directory of Open Access Journals (Sweden)

    Iluta Alexandru

    2011-11-01

    Full Text Available Iodine mineral waters are found especially in sub-Carpathian region, also in regions with Salif deposits. Waters are currently used iodine in drinking cure for chaps and Basedow. Are also indicated in balneology. Iodine water containing at least 1 mg L, there is pure iodine is usually given the nature of other types of mineral waters further: sodium chlorinated water (Bazna (50-70 mg iodine / l, Baile Govora (50 - 70 mg / l, Bălţăteşti (4-5 mg / l, salted Monteoru (30 mg / l, mine water mixed alkaline chlorination, sulphate, which are indicated for crenoterapie (hypo or isotonic to the bathrooms Olăneşti or Călimăneşti-Căciulata.

  19. MECHANICAL PROPERTIES AND CORROSION PROTECTION OF CARBON STEEL COATED WITH AN EPOXY BASED POWDER COATING CONTAINING MONTMORILONITE FUNCTIONALIZED WITH SILANE

    Directory of Open Access Journals (Sweden)

    Paula Tibola Bertuoli

    2014-06-01

    Full Text Available In the present work the MMT-Na+ clay was functionalized with 3-aminopropyltriethoxysilane (γ-APS and incorporated in a commercial formulation epoxy-based powder coating in a proportion of 8 wt% and applied on 1008 carbon steel panels by electrostatic spray. Adhesion, flexibility, impact and corrosion performance in salt spray chamber tests were performed to evaluate the coatings. The presence of clay did not affect the mechanical properties of the film, however greater subcutaneous migration was assessed after the completion of salt spray testing, which can compromise the use of paints obtained as primers.

  20. Iodine status in neonates in Denmark: regional variations and dependency on maternal iodine supplementation

    DEFF Research Database (Denmark)

    Nøhr, S B; Laurberg, P; Børlum, K G

    1994-01-01

    Iodine status of 147 neonates born in five different regions of Denmark was evaluated in relation to the iodine content of breast milk and iodine supplementation taken by the mother. Approximately two-thirds of the women had not received iodine supplementation. They had low iodine concentrations...... in breast milk and urinary iodine concentrations of the neonates at day 5 were low. The median values (milk/urine) were 33.6/31.7 micrograms/l (Randers 22/26, Ringkøbing 29/16, Aalborg 36/31. Arhus 54/41 and Copenhagen 55/59 micrograms/l). Higher values were found in the group where tablets containing...... iodine had been taken (milk/urine: 57.0/61.0 micrograms/l). In general, the values are low compared with internationally recommended levels. We suggest that mothers without autoimmune thyroid disease should receive iodine supplementation in the form of vitamin/mineral tablets containing iodine (150...

  1. Recent studies of laser science in paintings conservation and research.

    Science.gov (United States)

    Pouli, Paraskevi; Selimis, Alexandros; Georgiou, Savas; Fotakis, Costas

    2010-06-15

    The removal of aged and deteriorated molecular overlayers from the surface of paintings is a delicate and critical intervention in Cultural Heritage (CH) conservation. This irreversible action gets particularly complicated given the multitude of materials that may be present within a painted work of art (often in ultrathin layers or traces), as well as the exceptional sensitivity of the original surfaces to environmental conditions such as heat, light, and so on. Lasers hold an important role among the available cleaning methodologies, as they enable high control and accuracy, material selectivity, and immediate feedback. Still, prior to their implementation, it is imperative to optimize the cleaning parameters, so to ensure that any potential implications to the remaining materials are minimal and well understood. Toward this aim, research at IESL-FORTH is focused on both refining and continuously updating the laser-cleaning protocols (by introducing novel laser technologies into the field, i.e., ultrashort laser pulses), as well as on investigating and studying the nature and extent of laser-induced physicochemical alterations to the involved materials. In this Account, extended work for the understanding of ultraviolet (UV) laser ablation of polymers is presented. Emphasis is placed on the use of model systems (polymers doped with chromophores of known photochemistry) to examine the in-depth laser-induced modifications at the processed surfaces and thus to illustrate the dependence of their nature and extent on laser parameters and material properties. Furthermore, studies for the potential use of femtosecond UV pulses to overcome certain limitations involved with the nanosecond ablation of molecular overlayers from CH surfaces are highlighted. In particular, it is demonstrated that in the femtosecond regime any chemical modifications are, qualitatively and quantitatively, highly defined, limited and nearly independent of the material properties, such as the

  2. Urinary Iodine Clearance following Iodinated Contrast Administration: A Comparison of Euthyroid and Postthyroidectomy Subjects

    Directory of Open Access Journals (Sweden)

    Janice D. Ho

    2014-01-01

    Full Text Available Purpose. To compare iodine clearance following iodinated contrast administration in thyroidectomised thyroid cancer patients and euthyroid individuals. Methods. A convenience population (6 thyroidectomised thyroid cancer patients and 7 euthyroid controls was drawn from patients referred for iodinated contrast-enhanced computed tomography (CT studies. Subjects had sequential urine samples collected up to 6 months (50 samples from the thyroidectomised and 63 samples from the euthyroid groups. t-tests and generalised estimating equations (GEE were used to test for group differences in urinary iodine creatinine ratios. Results. Groups had similar urinary iodine creatinine ratios at baseline, with a large increase 2 weeks following iodinated contrast (P=0.005. Both groups had a return of urinary iodine creatinine ratios to baseline by 4 weeks, with no significant group differences overall or at any time point. Conclusions. Thyroidectomised patients did not have a significantly different urinary iodine clearance than euthyroid individuals following administration of iodinated contrast. Both had a return of urinary iodine creatinine ratios to baseline within 4 weeks.

  3. [Study on the iodine nutrition and iodine deficiency disorders status in pasturing areas of Tibet-a non-epidemic area of iodine deficiency disorders in serious iodine deficiency district].

    Science.gov (United States)

    DU, Dan; Li, Su-Mei; Li, Xiu-Wei; Wang, Hai-Yan; Li, Shu-Hua; Nima, Cangjue; Danzeng, Sangbu; Zhuang, Guang-Xiu

    2010-08-01

    To explore the status of iodine nutrition and iodine deficiency disorders in the pasturing areas and agricultural regions in Tibet. 30 families were selected respectively in pastoral Dangxiong county and agricultural Qushui county of Lasa. Drinking water and edible salt were collected for testing the iodine contents. In each type of the following populations including children aged 8 - 10, women of child-bearing age and male adults, 50 subjects were randomly sampled to examine their urinary iodine contents. Among them, 50 children and 50 women were randomly selected for goiter examination by palpation. Water iodine content was less than 2 µg/L, both in pasturing area and in agricultural areas. There was no iodized salt used in the families of pasturing areas, while 90% people consumed iodized salt in agricultural areas. The median of urinary iodine in pasturing area was 50.2 µg/L, significantly lower than that of agricultural area (193.2 µg/L). However, the goiter rate of children and women in pasturing area was significantly lower than that in agricultural area. Although iodine intake of populations in pasturing area of Tibet was severely deficient, there was no epidemic of Iodine Deficiency Disorders. This phenomenon noticed by the researchers deserved further investigation.

  4. Iodine deficiency disorders

    Energy Technology Data Exchange (ETDEWEB)

    Ali, S M [Pakistan Council for Science and Technology, Islamabad (Pakistan)

    1994-12-31

    Iodine deficiency (IDD) is one of the common problem in the diet. Iodine deficiency as prevalence of goiter in population occurs in the mountainous areas. There is consensus that 800 million people are at risk of IDD from living in iodine deficient area and 190 million from goiter. Very high prevalence of IDD in different parts of the world are striking. It has generally observed that in iodine-deficient areas about 50% are affected with goiter, 1-5% from cretinsim and 20% from impaired mental and/or mortor function. (A.B.).

  5. Iodine deficiency and thyroid disorders.

    Science.gov (United States)

    Zimmermann, Michael B; Boelaert, Kristien

    2015-04-01

    Iodine deficiency early in life impairs cognition and growth, but iodine status is also a key determinant of thyroid disorders in adults. Severe iodine deficiency causes goitre and hypothyroidism because, despite an increase in thyroid activity to maximise iodine uptake and recycling in this setting, iodine concentrations are still too low to enable production of thyroid hormone. In mild-to-moderate iodine deficiency, increased thyroid activity can compensate for low iodine intake and maintain euthyroidism in most individuals, but at a price: chronic thyroid stimulation results in an increase in the prevalence of toxic nodular goitre and hyperthyroidism in populations. This high prevalence of nodular autonomy usually results in a further increase in the prevalence of hyperthyroidism if iodine intake is subsequently increased by salt iodisation. However, this increase is transient because iodine sufficiency normalises thyroid activity which, in the long term, reduces nodular autonomy. Increased iodine intake in an iodine-deficient population is associated with a small increase in the prevalence of subclinical hypothyroidism and thyroid autoimmunity; whether these increases are also transient is unclear. Variations in population iodine intake do not affect risk for Graves' disease or thyroid cancer, but correction of iodine deficiency might shift thyroid cancer subtypes toward less malignant forms. Thus, optimisation of population iodine intake is an important component of preventive health care to reduce the prevalence of thyroid disorders. Copyright © 2015 Elsevier Ltd. All rights reserved.

  6. Iodine Status in Pregnant & Breastfeeding Women

    DEFF Research Database (Denmark)

    Andersen, Stine Linding

    Iodine is required for the synthesis of thyroid hormones, which are crucial regulator of early brain development. The source of iodine in the fetus and the breastfed infant is maternal iodine, and adequate iodine intake in pregnant and breastfeeding is of major concern. Severe iodine deficiency can...... cause irreversible brain damage, whereas the consequences of mild to moderate iodine deficiency are less clear. Denmark was previously iodine deficient with regional differences (mild iodine deficiency in East Denmark and moderate iodine deficiency in West Denmark), and also pregnant and breastfeeding...... women suffered from iodine deficiency. A mandatory iodine fortification of household salt and salt used for commercial production of bread was introduced in Denmark in the year 2000. The PhD thesis investigates intake of iodine supplements and urinary iodine status in Danish pregnant and breastfeeding...

  7. Consuming iodine enriched eggs to solve the iodine deficiency endemic for remote areas in Thailand

    Directory of Open Access Journals (Sweden)

    Teeyapant Punthip

    2010-12-01

    Full Text Available Abstract Background Evidence showed that the occurrence of iodine deficiency endemic areas has been found in every provinces of Thailand. Thus, a new pilot programme for elimination of iodine deficiency endemic areas at the community level was designed in 2008 by integrating the concept of Sufficient Economic life style with the iodine biofortification of nutrients for community consumption. Methods A model of community hen egg farm was selected at an iodine deficiency endemic area in North Eastern part of Thailand. The process for the preparation of high content iodine enriched hen food was demonstrated to the farm owner with technical transfer in order to ensure the sustainability in the long term for the community. The iodine content of the produced iodine enriched hen eggs were determined and the iodine status of volunteers who consumed the iodine enriched hen eggs were monitored by using urine iodine excretion before and after the implement of iodine enrichment in the model farm. Results The content of iodine in eggs from the model farm were 93.57 μg per egg for the weight of 55 - 60 g egg and 97.76 μg for the weight of 60 - 65 g egg. The biological active iodo-organic compounds in eggs were tested by determination of the base-line urine iodine of the volunteer villagers before and after consuming a hard boiled iodine enriched egg per volunteer at breakfast for five days continuous period in 59 volunteers of Ban Kew village, and 65 volunteers of Ban Nong Nok Kean village. The median base-line urine iodine level of the volunteers in these two villages before consuming eggs were 7.00 and 7.04 μg/dL respectively. After consuming iodine enriched eggs, the median urine iodine were raised to the optimal level at 20.76 μg/dL for Ban Kew and 13.95 μg/dL for Ban Nong Nok Kean. Conclusions The strategic programme for iodine enrichment in the food chain with biological iodo-organic compound from animal origins can be an alternative method to

  8. Iodine in meat in Macedonia

    International Nuclear Information System (INIS)

    Bogdanov, Bogdan; Gonev, Mihajlo; Tadzher, Isak

    2000-01-01

    Iodine deficiency in Macedonia still persists in a mild form. In 1999 the iodination of salt rose to 20 m gr iodine in Kg salt. The consumption of salt diminished after the last war from 20-30 gr salt per day to 10-20 gr salt daily. This shows that the problem of the elimination of iodine deficiency is being vigorously tackled. Since 1956 the iodine in salt in Macedonia rose to 10 m gr KI/Kg salt. The content of iodine in the Macedonian diet seems to be important. The amount of iodine in milk, eggs and bread is low as found by the investigation of MANU. The content of iodine in meat is low, compared to British meat is 10 times lower. The average iodine content in Macedonian meat is 95.15 micro gr per Kg, whereas in British meat it is 850-1510 micro gr iodine per k gr meat. (Original)

  9. Characterization of Epoxy Functionalized Graphite Nanoparticles and the Physical Properties of Epoxy Matrix Nanocomposites

    Science.gov (United States)

    Miller, Sandi G.; Bauer, Jonathan L.; Maryanski, Michael J.; Heimann, Paula J.; Barlow, Jeremy P.; Gosau, Jan-Michael; Allred, Ronald E.

    2010-01-01

    This work presents a novel approach to the functionalization of graphite nanoparticles. The technique provides a mechanism for covalent bonding between the filler and matrix, with minimal disruption to the sp2 hybridization of the pristine graphene sheet. Functionalization proceeded by covalently bonding an epoxy monomer to the surface of expanded graphite, via a coupling agent, such that the epoxy concentration was measured as approximately 4 wt.%. The impact of dispersing this material into an epoxy resin was evaluated with respect to the mechanical properties and electrical conductivity of the graphite-epoxy nanocomposite. At a loading as low as 0.5 wt.%, the electrical conductivity was increased by five orders of magnitude relative to the base resin. The material yield strength was increased by 30% and Young s modulus by 50%. These results were realized without compromise to the resin toughness.

  10. Self Cleaning Paint: Introduction of Photocatalytic Particles into a Paint System

    DEFF Research Database (Denmark)

    Gunnarsson, Sverrir Grimur

    The current industrial PhD work was aimed at synthesising a photocatalytic composite material which could be used to give organic wood paint films self-cleaning and anti-microbial properties. The current PhD work was done in collaboration between Dyrup A/S and Technical University of Denmark...... consists of an introduction to relevant concepts and literature followed by results, presented as research papers, and a patent application. Four research papers are introduced as individual chapters. Chapter 4 discusses the synthesis and optimisation of anatase TiO2 coated microspheres, chapter 5......-cleaning coatings containing TiO2 coated microspheres. The results show that introducing a photocatalyst into an organic paint system as a coating on inert carrier particles results in durable and weather stable paint films. The paint films exhibit selfcleaning properties and are able to resist the attack of micro...

  11. Iodine Hall Thruster

    Science.gov (United States)

    Szabo, James

    2015-01-01

    Iodine enables dramatic mass and cost savings for lunar and Mars cargo missions, including Earth escape and near-Earth space maneuvers. The demonstrated throttling ability of iodine is important for a singular thruster that might be called upon to propel a spacecraft from Earth to Mars or Venus. The ability to throttle efficiently is even more important for missions beyond Mars. In the Phase I project, Busek Company, Inc., tested an existing Hall thruster, the BHT-8000, on iodine propellant. The thruster was fed by a high-flow iodine feed system and supported by an existing Busek hollow cathode flowing xenon gas. The Phase I propellant feed system was evolved from a previously demonstrated laboratory feed system. Throttling of the thruster between 2 and 11 kW at 200 to 600 V was demonstrated. Testing showed that the efficiency of iodine fueled BHT-8000 is the same as with xenon, with iodine delivering a slightly higher thrust-to-power (T/P) ratio. In Phase II, a complete iodine-fueled system was developed, including the thruster, hollow cathode, and iodine propellant feed system. The nominal power of the Phase II system is 8 kW; however, it can be deeply throttled as well as clustered to much higher power levels. The technology also can be scaled to greater than 100 kW per thruster to support megawatt-class missions. The target thruster efficiency for the full-scale system is 65 percent at high specific impulse (Isp) (approximately 3,000 s) and 60 percent at high thrust (Isp approximately 2,000 s).

  12. Selectively strippable paint schemes

    Science.gov (United States)

    Stein, R.; Thumm, D.; Blackford, Roger W.

    1993-03-01

    In order to meet the requirements of more environmentally acceptable paint stripping processes many different removal methods are under evaluation. These new processes can be divided into mechanical and chemical methods. ICI has developed a paint scheme with intermediate coat and fluid resistant polyurethane topcoat which can be stripped chemically in a short period of time with methylene chloride free and phenol free paint strippers.

  13. Marine geochemistry of iodine

    International Nuclear Information System (INIS)

    Kennedy, H.; Elderfield, H.

    1985-01-01

    Iodine has long been classified as a biophilic element with analyses showing that iodine is strongly enriched, relative to seawater concentrations in both plankton and particulate matter and that the concentration of iodine found in surface sediments is still further enriched relative to that found in the sedimenting particulate matter. The extent of enrichment of iodine relative to carbon in deep sea surface sediments has been shown to depend on the carbon accumulation rate. Iodine decomposition rates have been calculated and are shown to vary with the sedimentation rate in the same manner as has been shown for organic carbon. Vertical profiles of total dissolved iodine, iodate and iodide in interstitial waters of sediments from the north east Atlantic are characterised by three zones of reaction as identified by changes in the concentration of iodate and iodide. These reaction zones represent (i) iodide production (ii) iodide oxidation and (iii) iodate reduction. Pore water and solid phase iodine profiles from cores containing turbidite units have shown that iodine, released to pore waters as iodide during the oxidation of the organic matter, has been scavenged after diffusing upwards into a less reducing region of the sediment. (author)

  14. Analysis of iodine content in seaweed by GC-ECD and estimation of iodine intake

    Directory of Open Access Journals (Sweden)

    Tai Sheng Yeh

    2014-06-01

    Full Text Available Edible seaweed products have been consumed in many Asian countries. Edible seaweeds accumulate iodine from seawater, and are therefore a good dietary source of iodine. An adequate consumption of seaweed can eliminate iodine deficiency disorders, but excessive iodine intake is not good for health. The recommended dietary reference intake of 0.15 mg/d and 0.14 mg/d for iodine has been established in the United States and Taiwan, respectively. In this study, 30 samples of seaweed were surveyed for iodine content. The samples included 10 nori (Porphyra, 10 wakame (Undaria, and 10 kombu (Laminaria products. The iodine in seaweed was derivatized with 3-pentanone and detected by gas chromatography-electron capture detector (GC-ECD. The method detection limit was 0.5 mg/kg. The iodine content surveyed for nori was 29.3–45.8 mg/kg, for wakame 93.9–185.1 mg/kg, and for kombu 241–4921 mg/kg. Kombu has the highest average iodine content 2523.5 mg/kg, followed by wakame (139.7 mg/kg and nori (36.9 mg/kg. The GC-ECD method developed in this study is a low-cost alternative to inductively coupled plasma-optical emission spectroscopy for iodine detection in seaweeds. The iodine intake from seaweed in the current survey was calculated and compared with the iodine dietary reference intake of Taiwan. The risk and benefit of seaweed consumption is also discussed.

  15. Painting for protection

    International Nuclear Information System (INIS)

    Stepto, G.G.C.

    1981-01-01

    Despite the use of special alloys, paint is still the most economical and practical method of protecting steel. Chlorinated rubber resin based paint systems are shown to be satisfactory in areas requiring decontamination as well as for outside exposed areas of nuclear power plants. (author)

  16. Breast-Milk Iodine Concentrations and Iodine Levels of Infants According to the Iodine Status of the Country of Residence: A Systematic Review and Meta-Analysis.

    Science.gov (United States)

    Nazeri, Pantea; Kabir, Ali; Dalili, Hosein; Mirmiran, Parvin; Azizi, Fereidoun

    2018-01-01

    Iodine, an essential micronutrient, plays a critical role in normal growth and development, especially during the first two years of life. This systematic review and meta-analysis is among the first to evaluate breast-milk iodine concentrations and infant iodine status in countries characterized by iodine sufficiency or deficiency. PubMed, Web of Science, Cochrane Library, Google Scholar, and other relevant databases, as well as reference lists of previous reviews, were searched for relevant studies published between 1986 and 2016. Mean or median breast-milk and infant urinary iodine concentrations, along with other relevant data, were extracted from eligible studies. Each study was assessed for quality and risk of bias. Of the 496 identified studies, 57 met the criteria for inclusion in the meta-analysis. The mean (confidence interval [CI]) iodine concentrations in maternal colostrum were 152.0 μg/L [CI 106.2-198.7 μg/L] and 57.8 μg/L [CI 41.4-74.1 μg/L] in iodine-sufficient and -deficient countries, respectively, indicating a significant difference between the two iodine statuses. By contrast, the corresponding values in mature milk did not differ significantly between mothers in iodine-sufficient and -deficient countries (71.5 μg/L [CI 51.0-92.0 μg/L] and 28.0 μg/L [CI -13.8 to 69.9 μg/L], respectively]. The weighted urinary iodine levels [CIs] of breast-fed infants in iodine-sufficient countries were significantly higher than those in iodine-deficient countries (164.5 μg/L [CI 116.4-212.7 μg/L] vs. 70.4 μg/L [CI 46.2-94.6 μg/L]). Similarly, a significant difference was observed in the pooled estimates of urinary iodine levels [CIs] among formula-fed infants in iodine-sufficient versus iodine-deficient countries (310.3 μg/L [CI 287.4-342.1 μg/L] vs. 38.3 μg/L [CI 23.4-53.2 μg/L]). The meta-analysis reveals that in iodine-sufficient countries, the mean iodine concentrations in colostrum and mature breast milk

  17. Non-destructive synchrotron X-ray diffraction mapping of a Roman painting

    International Nuclear Information System (INIS)

    Dooryhee, E.; Anne, M.; Hodeau, J.-L.; Martinetto, P.; Rondot, S.; Bardies, I.; Salomon, J.; Walter, P.; Vaughan, G.B.M.

    2005-01-01

    The history and the properties of materials are deduced not only from their elemental and molecular signatures, but also from their exact phase compositions, and from the structures and the defects of their constituents. Here we implement a non-destructive synchrotron X-ray based method, which combines both the quantitative structural content of diffraction and the imaging mode. As a demonstration case, the pigments of a Roman wall painting are examined. The joined elemental and mineral maps mimic the major features of the painting. Different structural phases made of common atomic elements are differentiated. Textures and graininess are measured and related to the artist's know-how. (orig.)

  18. Effect of carbon nanotube dispersion on glass transition in cross-linked epoxy-carbon nanotube nanocomposites: role of interfacial interactions.

    Science.gov (United States)

    Khare, Ketan S; Khare, Rajesh

    2013-06-20

    We have used atomistic molecular simulations to study the effect of nanofiller dispersion on the glass transition behavior of cross-linked epoxy-carbon nanotube (CNT) nanocomposites. Specific chemical interactions at the interface of CNTs and cross-linked epoxy create an interphase region, whose impact on the properties of their nanocomposites increases with an increasing extent of dispersion. To investigate this aspect, we have compared the volumetric, structural, and dynamical properties of three systems: neat cross-linked epoxy, cross-linked epoxy nanocomposite containing dispersed CNTs, and cross-linked epoxy nanocomposite containing aggregated CNTs. We find that the nanocomposite containing dispersed CNTs shows a depression in the glass transition temperature (Tg) by ~66 K as compared to the neat cross-linked epoxy, whereas such a large depression is absent in the nanocomposite containing aggregated CNTs. Our results suggest that the poor interfacial interactions between the CNTs and the cross-linked epoxy matrix lead to a more compressible interphase region between the CNTs and the bulk matrix. An analysis of the resulting dynamic heterogeneity shows that the probability of percolation of immobile domains becomes unity near the Tg calculated from volumetric properties. Our observations also lend support to the conceptual analogy between polymer nanocomposites and the nanoconfinement of polymer thin films.

  19. Radioactive iodine intake through foodstuff

    International Nuclear Information System (INIS)

    Omomo, Yoichiro

    1974-01-01

    The transition of radioactive iodine to human bodies is affected by the amount of coexisting stable iodine. The intake of stable iodine through foodstuffs was studied from the stand point of I) discussion of the literature which states the approximate amounts of stable iodine contained in environmental materials, and II) the authors' research on the consumption of foodstuffs. For example, the amounts of iodine intake of fishermen living in Kuji-cho (Ibaragi Prefecture) was estimated from I and II, and was revealed as 2704p. The national average iodine intake was about 800p indicating that the former estimated value was remarkably high. Eighty Four per cent of the 2.7 mg iodine intake was taken from marine products, indicating that marine products are important sources of iodine supply. (Tsukamoto, Y.)

  20. FDA regulations regarding iodine addition to foods and labeling of foods containing added iodine12

    Science.gov (United States)

    Trumbo, Paula R

    2016-01-01

    The US Food and Drug Administration (FDA) regulates the addition of iodine to infant formulas, the iodization of salt, and the addition of salt and iodine to foods. The required amount of iodine in infant formulas is based on caloric content, and the label must provide the iodine content per 100 kcal. Cuprous iodide and potassium iodide may be added to table salt as a source of dietary iodine at a maximum amount of 0.01%; if added, the label must indicate that the salt is iodized. Table salt to which iodine has not been added must bear the statement, “This salt does not supply iodide, a necessary nutrient.” If a nutrient is to be appropriately added to a food for the purpose of correcting a dietary insufficiency, there should be sufficient scientific information available to demonstrate a nutritional deficiency and/or identify a public health problem. Furthermore, the population groups that would benefit from the proposed fortification should be identified. If iodine is added to a food, the percent Daily Value of iodine must be listed. There are no FDA regulations governing ingredient standards for dietary supplements. As a result, some dietary supplements include iodine and others do not. If a supplement contains iodine, the Supplement Facts label must list iodine as a nutrient ingredient. If iodine is not listed on the Supplement Facts label, then it has not been added. There are similarities between the FDA, which establishes US food regulations and policies, and the Codex Alimentarius (Codex), which develops international food standards and guidelines under the aegis of the FAO and the WHO. Both the FDA and Codex call for the labeling of table salt to indicate fortification with iodine, voluntary labeling of iodine on foods, and a Daily Value (called a Nutrient Reference Value by Codex) of 150 μg for iodine. PMID:27534626

  1. Some Aspects of Thermal Transport across the Interface between Graphene and Epoxy in Nanocomposites.

    Science.gov (United States)

    Wang, Yu; Yang, Chunhui; Pei, Qing-Xiang; Zhang, Yingyan

    2016-03-01

    Owing to the superior thermal properties of graphene, graphene-reinforced polymer nanocomposites hold great potential as the thermal interface materials (TIMs) dissipating heat for electronic packages. However, this application is greatly hindered by the high thermal resistance at the interface between graphene and polymer. In this paper, some important aspects of the improvement of the thermal transport across the interface between graphene and epoxy in graphene-epoxy nanocomposites, including the effectiveness of covalent and noncovalent functionalization, isotope doping, and acetylenic linkage in graphene are systematically investigated using molecular dynamics (MD) simulations. The simulation results show that the covalent and noncovalent functionalization techniques could considerably reduce the graphene-epoxy interfacial thermal resistance in the nanocomposites. Among different covalent functional groups, butyl is more effective than carboxyl and hydroxyl in reducing the interfacial thermal resistance. Different noncovalent functional molecules, including 1-pyrenebutyl, 1-pyrenebutyric acid, and 1-pyrenebutylamine, yield a similar amount of reductions. Moreover, it is found that the graphene-epoxy interfacial thermal resistance is insensitive to the carbon isotope doping in graphene, while it can be reduced moderately by replacing the sp(2) bonds in graphene with acetylenic linkages.

  2. Spectroscopic studies of molecular iodine emitted into the gas phase by seaweed

    Directory of Open Access Journals (Sweden)

    S. M. Ball

    2010-07-01

    Full Text Available Time profiles of molecular iodine emissions from seven species of seaweed have been measured at high time resolution (7.5 s by direct spectroscopic quantification of the gas phase I2 using broadband cavity enhanced absorption spectroscopy. Substantial differences were found between species, both in the amounts of I2 emitted when the plants were exposed to air and in the shapes of their emission time profiles. Two species of kelp, Laminaria digitata and Laminaria hyperborea, were found to be the most potent emitters, producing an intense burst of I2 when first exposed to air. I2 was also observed from Saccharina latissima and Ascophyllum nodosum but in lower amounts and with broader time profiles. I2 mixing ratios from two Fucus species and Dictyopteris membranacea were at or below the detection limit of the present instrument (25 pptv. A further set of experiments investigated the time dependence of I2 emissions and aerosol particle formation when fragments of L. digitata were exposed to desiccation in air, to ozone and to oligoguluronate stress factors. Particle formation occurred in all L. digitata stress experiments where ozone and light were present, subject to the I2 mixing ratios being above certain threshold amounts. Moreover, the particle number concentrations closely tracked variations in the I2 mixing ratios, confirming the results of previous studies that the condensable particle-forming gases derive from the photochemical oxidation of the plant's I2 emissions. This work also supports the theory that particle nucleation in the coastal atmosphere occurs in "hot-spot" regions of locally elevated concentrations of condensable gases: the greatest atmospheric concentrations of I2 and hence of condensable iodine oxides are likely to be above plants of the most efficiently

  3. Radioactive Iodine Treatment for Hyperthyroidism

    Science.gov (United States)

    ... Balance › Radioactive Iodine for Hyperthyroidism Fact Sheet Radioactive Iodine for Hyperthyroidism April, 2012 Download PDFs English Zulu ... prepare for RAI or surgery. How does radioactive iodine treatment work? Iodine is important for making thyroid ...

  4. Surface treated fly ash filled modified epoxy composites

    Directory of Open Access Journals (Sweden)

    Uma Dharmalingam

    2015-01-01

    Full Text Available Abstract Fly ash, an inorganic alumino silicate has been used as filler in epoxy matrix, but it reduces the mechanical properties due to its poor dispersion and interfacial bonding with the epoxy matrix. To improve its interfacial bonding with epoxy matrix, surface treatment of fly ash was done using surfactant sodium lauryl sulfate and silane coupling agent glycidoxy propyl trimethoxy silane. An attempt is also made to reduce the particle size of fly ash using high pressure pulverizer. To improve fly ash dispersion in epoxy matrix, the epoxy was modified by mixing with amine containing liquid silicone rubber (ACS. The effect of surface treated fly ash with varying filler loadings from 10 to 40% weight on the mechanical, morphological and thermal properties of modified epoxy composites was investigated. The surface treated fly ash was characterized by particle size analyzer and FTIR spectra. Morphological studies of surface treated fly ash filled modified epoxy composites indicate good dispersion of fillers in the modified epoxy matrix and improves its mechanical properties. Impact strength of the surface treated fly ash filled modified epoxy composites show more improvement than unmodified composites.

  5. Effect of the hardener to epoxy monomer ratio on the water absorption behavior of the DGEBA/TETA epoxy system

    Directory of Open Access Journals (Sweden)

    Ayrton Alef Castanheira Pereira

    2016-02-01

    Full Text Available Abstract The water absorption behavior of the DGEBA/TETA epoxy system was evaluated as a function of the epoxy monomer to amine hardener ratio. Weight gain versus immersion time curves were obtained and the experimental points were fitted using Fickian and Non-Fickian diffusion models. The results obtained showed that for all epoxy monomer to hardener ratios analyzed water diffusion followed non-Fickian behavior. It was possible to correlate the water absorption behavior to the macromolecular structure developed when the epoxy/ hardener ratio was varied. All epoxy/hardener ratios present a two-phase macromolecular structure, composed of regions with high crosslink density and regions with lower crosslinking. Epoxy rich systems have a more open macromolecular structure with a lower fraction of the dense phase than the amine rich systems, which present a more compact two-phase structure.

  6. Estimation of iodine intake from various urinary iodine measurements in population studies

    DEFF Research Database (Denmark)

    Vejbjerg, P.; Knudsen, N.; Perrild, H.

    2009-01-01

    Background: Iodine intake is often measured by a surrogate measure, namely urine iodine excretion as almost all ingested iodine is excreted in the urine. However, the methods for urine collection and the reporting of the results vary. These methods, and their advantages and disadvantages, are con...

  7. Order-fractal transitions in abstract paintings

    Energy Technology Data Exchange (ETDEWEB)

    Calleja, E.M. de la, E-mail: elsama79@gmail.com [Instituto de Física, Universidade Federal do Rio Grande do Sul, Caixa Postal 15051, 91501-970, Porto Alegre, RS (Brazil); Cervantes, F. [Department of Applied Physics, CINVESTAV-IPN, Carr. Antigua a Progreso km.6, Cordemex, C.P.97310, Mérida, Yucatán (Mexico); Calleja, J. de la [Department of Informatics, Universidad Politécnica de Puebla, 72640 (Mexico)

    2016-08-15

    In this study, we determined the degree of order for 22 Jackson Pollock paintings using the Hausdorff–Besicovitch fractal dimension. Based on the maximum value of each multi-fractal spectrum, the artworks were classified according to the year in which they were painted. It has been reported that Pollock’s paintings are fractal and that this feature was more evident in his later works. However, our results show that the fractal dimension of these paintings ranges among values close to two. We characterize this behavior as a fractal-order transition. Based on the study of disorder-order transition in physical systems, we interpreted the fractal-order transition via the dark paint strokes in Pollock’s paintings as structured lines that follow a power law measured by the fractal dimension. We determined self-similarity in specific paintings, thereby demonstrating an important dependence on the scale of observations. We also characterized the fractal spectrum for the painting entitled Teri’s Find. We obtained similar spectra for Teri’s Find and Number 5, thereby suggesting that the fractal dimension cannot be rejected completely as a quantitative parameter for authenticating these artworks. -- Highlights: •We determined the degree of order in Jackson Pollock paintings using the Hausdorff–Besicovitch dimension. •We detected a fractal-order transition from Pollock’s paintings between 1947 and 1951. •We suggest that Jackson Pollock could have painted Teri’s Find.

  8. Measurement of small-signal gain on COIL with chemically generated molecular iodine

    Czech Academy of Sciences Publication Activity Database

    Jirásek, Vít; Špalek, Otomar; Čenský, Miroslav; Kodymová, Jarmila

    2010-01-01

    Roč. 46, č. 9 (2010), s. 1350-1353 ISSN 0018-9197 Institutional research plan: CEZ:AV0Z10100523 Keywords : chemical lasers * iodine * gain measurement Subject RIV: BH - Optics, Masers, Lasers Impact factor: 2.477, year: 2010

  9. Suboptimal Iodine Concentration in Breastmilk and Inadequate Iodine Intake among Lactating Women in Norway.

    Science.gov (United States)

    Henjum, Sigrun; Lilleengen, Anne Marie; Aakre, Inger; Dudareva, Anna; Gjengedal, Elin Lovise Folven; Meltzer, Helle Margrete; Brantsæter, Anne Lise

    2017-06-22

    Breastfed infants depend on sufficient maternal iodine intake for optimal growth and neurological development. Despite this, few studies have assessed iodine concentrations in human milk and there is currently no published data on iodine status among lactating women in Norway. The aim of this study was to assess iodine concentrations in breast milk (BMIC) in lactating women and estimate iodine intake. Five Mother and Child Health Centres in Oslo were randomly selected during 2016, and 175 lactating women between 2nd and 28th weeks postpartum participated. Each of the women provided four breastmilk samples which were pooled and analysed for iodine concentrations. Participants also provided information on iodine intake from food and supplements covering the last 24 h and the habitual iodine intake (food frequency questionnaire). The median (p25, p75 percentiles) BMIC was 68 (45, 98) µg/L and 76% had BMIC food (p25, p75) was 121 (82, 162) µg/day and the total intake (food and supplements) was 134 (95, 222) µg/day. The majority of lactating women had suboptimal BMIC and inadequate intake of iodine from food and supplements.

  10. The application of epoxy resin coating in grounding grid

    Science.gov (United States)

    Hu, Q.; Chen, Z. R.; Xi, L. J.; Wang, X. Y.; Wang, H. F.

    2018-01-01

    Epoxy resin anticorrosion coating is widely used in grounding grid corrosion protection because of its wide range of materials, good antiseptic effect and convenient processing. Based on the latest research progress, four kinds of epoxy anticorrosive coatings are introduced, which are structural modified epoxy coating, inorganic modified epoxy coating, organic modified epoxy coating and polyaniline / epoxy resin composite coating. In this paper, the current research progress of epoxy base coating is analyzed, and prospected the possible development direction of the anti-corrosion coating in the grounding grid, which provides a reference for coating corrosion prevention of grounding materials.

  11. Measurement of thyroid volume, iodine concentration and total iodine content by CT and its clinical significance

    International Nuclear Information System (INIS)

    Nakaji, Shunsuke; Imanishi, Yoshimasa; Okamoto, Kyouko; Shinagawa, Toshihito

    2007-01-01

    Recently, Imanishi et al have developed new CT software for quantitative in vivo measurement of thyroid iodine. Using a CT system with the software, we measured volume, iodine concentration and total iodine content of thyroids in 63 controls and 435 patients with various diffuse thyroid diseases and thyroid nodules. In controls, all of them showed no difference between the sexes. Although the iodine concentration of the thyroid showed no difference among children, adults and seniles, the volume and total iodine content of the thyroid appeared smaller in children and seniles than in adults. In addition, although the volume and iodine concentration of the thyroid had two peaks in distribution, the total iodine content had almost normal distribution. Normal range of volume, iodine concentration and total iodine content in adults were 5.2-15.5 cm 3 , 0.28831-0.85919 mg/cm 3 and 2.35-11.69 mg, respectively. In thyroid nodule, there is no significant difference in volume, iodine concentration and total iodine content between benign and malignant nodules. All nodules with iodine concentration of less than 0.00007 mg/cm 3 were benign. No thyroid was higher in iodine concentration than the normal range although the thyroid was lower in 78.7% of patients with diffuse thyroid diseases. In all thyroids with increasing iodine concentration and total iodine content in medication course, thyroidal symptoms and signs were uncontrollable by the medication. In 43.8% of patients with long-period systemic diseases, the thyroid showed abnormality in any of the three. We concluded that quantitative in vivo measurement of thyroid iodine by CT could assist the diagnosis of thyroid diseases and decision of therapeutic methods. (author)

  12. Solving the problem of building models of crosslinked polymers: an example focussing on validation of the properties of crosslinked epoxy resins.

    Directory of Open Access Journals (Sweden)

    Stephen A Hall

    Full Text Available The construction of molecular models of crosslinked polymers is an area of some difficulty and considerable interest. We report here a new method of constructing these models and validate the method by modelling three epoxy systems based on the epoxy monomers bisphenol F diglycidyl ether (BFDGE and triglycidyl-p-amino phenol (TGAP with the curing agent diamino diphenyl sulphone (DDS. The main emphasis of the work concerns the improvement of the techniques for the molecular simulation of these epoxies and specific attention is paid towards model construction techniques, including automated model building and prediction of glass transition temperatures (T(g. Typical models comprise some 4200-4600 atoms (ca. 120-130 monomers. In a parallel empirical study, these systems have been cast, cured and analysed by dynamic mechanical thermal analysis (DMTA to measure T(g. Results for the three epoxy systems yield good agreement with experimental T(g ranges of 200-220°C, 270-285°C and 285-290°C with corresponding simulated ranges of 210-230°C, 250-300°C, and 250-300°C respectively.

  13. Accelerated bridge paint test program.

    Science.gov (United States)

    2011-07-06

    The accelerated bridge paint (AB-Paint) program evaluated a new Sherwin-Williams two-coat, : fast-curing paint system. The system is comprised of an organic zinc-rich primer (SW Corothane I : Galvapac One-Pack Zinc-Rich Primer B65 G11) and a polyurea...

  14. Characterization of Streptomyces isolates causing colour changes of mural paintings in ancient Egyptian tombs.

    Science.gov (United States)

    Abdel-Haliem, M E F; Sakr, A A; Ali, M F; Ghaly, M F; Sohlenkamp, C

    2013-08-25

    Paintings in ancient Egyptian tombs often suffer colour changes due to microbial growth and colonization. Streptomyces strains were isolated from mural paintings of Tell Basta and Tanis tombs (East of Nile Delta, Egypt) and were identified using biochemical and molecular methods. The16S rDNA sequences data indicated that isolated strains were closely related to S. coelicolor, S. albidofuscus, S. ambofaciens, S. canarius, S. parvullus, S. corchorusii, S. albidofuscus and S. nigrifaciens. It could be shown that Streptomyces strains are involved on a large scale in the colour changes of paintings and stone support by producing a wide range of metabolites such as acids (oxalic, citric and sulphuric acids), biopigments of melanin, carotenoids, and hydrogen sulphide. Copyright © 2013 Elsevier GmbH. All rights reserved.

  15. Contact allergy to epoxy (meth)acrylates.

    Science.gov (United States)

    Aalto-Korte, Kristiina; Jungewelter, Soile; Henriks-Eckerman, Maj-Len; Kuuliala, Outi; Jolanki, Riitta

    2009-07-01

    Contact allergy to epoxy (meth)acrylates, 2,2-bis[4-(2-hydroxy-3-methacryloxypropoxy) phenyl]propane (bis-GMA), 2,2-bis[4-(2-hydroxy-3-acryloxypropoxy)phenyl]-propane (bis-GA), 2,2-bis[4-(methacryl-oxyethoxy)phenyl] propane (bis-EMA), 2,2-bis[4-(methacryloxy)phenyl]-propane (bis-MA), and glycidyl methacrylate (GMA) is often manifested together with contact allergy to diglycidyl ether of bisphenol A (DGEBA) epoxy resin. To analyse patterns of concomitant allergic reactions to the five epoxy (meth)acrylates in relation to exposure. We reviewed the 1994-2008 patch test files at the Finnish Institute of Occupational Health (FIOH) for reactions to the five epoxy (meth)acrylates, and examined the patients' medical records for exposure. Twenty-four patients had an allergic reaction to at least one of the studied epoxy (meth)acrylates, but specific exposure was found only in five patients: two bis-GMA allergies from dental products, two bis-GA allergies from UV-curable printing inks, and one bis-GA allergy from an anaerobic glue. Only 25% of the patients were negative to DGEBA epoxy resin. The great majority of allergic patch test reactions to bis-GMA, bis-GA, GMA and bis-EMA were not associated with specific exposure, and cross-allergy to DGEBA epoxy resin remained a probable explanation. However, independent reactions to bis-GA indicated specific exposure. Anaerobic sealants may induce sensitization not only to aliphatic (meth)acrylates but also to aromatic bis-GA.

  16. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    Energy Technology Data Exchange (ETDEWEB)

    Jalili, M. [Nanomaterials and Nanocoatings Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Surface Coatings and Corrosion Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Rostami, M. [Nanomaterials and Nanocoatings Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of); Ramezanzadeh, B., E-mail: ramezanzadeh-bh@icrc.ac.ir [Surface Coatings and Corrosion Department, Institute for Color Science and Technology (ICST), PO 16765-654, Tehran (Iran, Islamic Republic of)

    2015-02-15

    Highlights: • Aluminum nanoparticle was modified with amino trimethylene phosphonic acid. • 2 wt% of zinc dust in zinc-rich paint was substituted by aluminum nanoparticles. • Surface modified aluminum nanoparticle improved the cathodic period of protection. • Aluminum nanoparticles enhanced the corrosion protection of the zinc-rich coating. - Abstract: Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties.

  17. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    International Nuclear Information System (INIS)

    Jalili, M.; Rostami, M.; Ramezanzadeh, B.

    2015-01-01

    Highlights: • Aluminum nanoparticle was modified with amino trimethylene phosphonic acid. • 2 wt% of zinc dust in zinc-rich paint was substituted by aluminum nanoparticles. • Surface modified aluminum nanoparticle improved the cathodic period of protection. • Aluminum nanoparticles enhanced the corrosion protection of the zinc-rich coating. - Abstract: Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties

  18. Local radiolytic effectiveness of Auger electrons of iodine-125 in benzene-iodine solutions

    International Nuclear Information System (INIS)

    Uenak, P.; Uenak, T.

    1987-01-01

    High radiotoxicity of iodine-125 has been mainly attributed to the local radiolytic effects of Auger electrons on biological systems. In the present study, experimental and theoretical results are compared. The agreement between the experimental and theoretical results explains that the energy absorption of iodine aggregates has an important role in the radiolytic effectiveness of Auger electrons and iodine-125 in benzene-iodine solutions. (author) 18 refs.; 3 figs

  19. Surface analytical investigations of the release behaviour of volatile fission products during simulated core meltdown accidents and of the reaction behaviour of iodine with silver surfaces

    International Nuclear Information System (INIS)

    Moers, H.

    1986-07-01

    The report presents the results of the analysis of aerosol particles formed in simulated laboratory scale core meltdown experiments. In addition the interaction of silver surfaces with gaseous molecular iodine and with iodide and molecular iodine in aqueous solution was investigated. The composition of the aerosol samples and the progress of the reactions mentioned were determined by use of surface analytical techniques (X-ray photoelectron spectroscopy, Auger electron spectroscopy, secondary ion mass spectroscopy). The major information can be evaluated from X-ray photoelectron spectra which exhibit chemical shifts of the photoelectron lines which allowing a discrimination between different chemical species of the same element. The analyses showed that iodine is present in the aerosol particles mainly as caesium iodide and, to a smaller fraction, as silver iodide. During the adsorption of gaseous molecular iodine at metallic silver surfaces a closed silver iodide overlayer is formed. In aqueous iodide solutions one observes chemisorption of the iodide anions up to a coverage of the metallic silver surface of about half a monolayer. Molecular iodine in aqueous solution is completely converted to silver iodide which covers the substrate irregularly. (orig./HP) [de

  20. Structuralist readings: Painting vs. picture

    Directory of Open Access Journals (Sweden)

    Marinkov-Pavlović Lidija

    2016-01-01

    Full Text Available The aim of the paper is to point to two fundamentally different strategies of painting practice, that is, to two subsystems of painting: picture and painting. This differentiation can be made within the framework of semiotic and semiological analyses which have developed in theory under the influence of structuralism. The first part of the paper offers a basic insight into the linguistic foundation of structuralistic concept, and then sets a thesis about the possibility of analogue reconceptualisation of semiotics/semiology of painting through Julia Kristeva's semiotics and Roland Barthes' semiology. In addition, it points to the concrete concepts of structural analysis which have accentuated the opposition picture-painting with the examples of art practice concurrent to the development of structuralism. However, what is revealed is that various structuralist readings are significantly subjective to unstable relationship between the basic elements in the pictorial object, that is, in the work of painting.

  1. Volume changes at macro- and nano-scale in epoxy resins studied by PALS and PVT experimental techniques

    Energy Technology Data Exchange (ETDEWEB)

    Somoza, A. [IFIMAT-UNCentro, Pinto 399, B7000GHG Tandil (Argentina) and CICPBA, Pinto 399, B7000GHG Tandil (Argentina)]. E-mail: asomoza@exa.unicen.edu.ar; Salgueiro, W. [IFIMAT-UNCentro, Pinto 399, B7000GHG Tandil (Argentina); Goyanes, S. [LPMPyMC, Depto. de Fisica, Facultad de Ciencias Exactas y Naturales, Universidad de Buenos Aires, Ciudad Universitaria, Pabellon I, 1428 Buenos Aires (Argentina); Ramos, J. [Materials and Technology Group, Departamento de Ingenieria Quimica y M. Ambiente, Escuela University Politecnica, Universidad Pais Vasco/Euskal Herriko Unibertsitatea, Pz. Europa 1, 20018 Donostia/San Sebastian (Spain); Mondragon, I. [Materials and Technology Group, Departamento de Ingenieria Quimica y M. Ambiente, Escuela University Politecnica, Universidad Pais Vasco/Euskal Herriko Unibertsitatea, Pz. Europa 1, 20018 Donostia/San Sebastian (Spain)

    2007-02-15

    A systematic study on changes in the volumes at macro- and nano-scale in epoxy systems cured with selected aminic hardeners at different pre-cure temperatures is presented. Free- and macroscopic specific-volumes were measured by PALS and pressure-volume-temperature techniques, respectively. An analysis of the relation existing between macro- and nano-scales of the thermosetting networks developed by the different chemical structures is shown. The result obtained indicates that the structure of the hardeners governs the packing of the molecular chains of the epoxy network.

  2. Controversies in urinary iodine determinations

    OpenAIRE

    Soldin, Offie Porat

    2002-01-01

    Iodine deficiency (ID) is associated with increased prevalence of goiter, increased risk for neurodevelopmental disorders, and is the world’s leading cause of intellectual deficits. Iodine nutritional status of a population is assessed by measurements of urinary iodine concentrations which are also used to define, indicate, survey and monitor iodine deficiency and consequently its treatment. Several methods are available for urinary iodine determination. Discussed here are some of the limitat...

  3. Design of carbon nanofiber embedded conducting epoxy resin

    International Nuclear Information System (INIS)

    Gantayat, Subhra; Sarkar, Niladri; Rout, Dibyaranjan; Swain, Sarat K.

    2017-01-01

    Acid treated carbon nanofiber (t-CNF) reinforced epoxy nanocomposites were fabricated by hand lay-up method with various wt % of t-CNF loadings. Pristine or unmodified carbon nano fibers (u-CNFs) were made compatible with epoxy matrix by means of mixed acid treatment. Fabricated nanocomposites were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) study, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Mechanical and thermal properties of the nanocomposites were measured as a function of t-CNF content. Effect of acid treated CNFs on to the mechanical properties of epoxy nanocomposites was justified by comparing the mechanical properties of epoxy/t-CNF and epoxy/u-CNF nanocomposites with same loading level. The electrical conductivity was achieved by epoxy resin with a threshold at 1 wt % of t-CNF. Substantial improvement in thermal, mechanical and electrical properties of the synthesized epoxy/t-CNF nanocomposites may be suitable for fabricating electronic devices. - Highlights: • Epoxy/t-CNF nanocomposites are characterized by XRD, FTIR, SEM, AFM and TEM. • Electrical conductivity was achieved by epoxy with a threshold at 1 wt% of t-CNF. • Tensile strength is enhanced by 40% due to dispersion of t-CNF. • Synthesized nanocomposites are suitable for fabricating electronic devises.

  4. Design of carbon nanofiber embedded conducting epoxy resin

    Energy Technology Data Exchange (ETDEWEB)

    Gantayat, Subhra [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India); School of Applied Sciences, KIIT University, Bhubaneswar 751024, Odisha (India); Sarkar, Niladri [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India); Rout, Dibyaranjan [School of Applied Sciences, KIIT University, Bhubaneswar 751024, Odisha (India); Swain, Sarat K., E-mail: swainsk2@yahoo.co.in [Department of Chemistry, Veer Surendra Sai University of Technology, Burla, Sambalpur 768018, Odisha (India)

    2017-01-15

    Acid treated carbon nanofiber (t-CNF) reinforced epoxy nanocomposites were fabricated by hand lay-up method with various wt % of t-CNF loadings. Pristine or unmodified carbon nano fibers (u-CNFs) were made compatible with epoxy matrix by means of mixed acid treatment. Fabricated nanocomposites were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) study, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Mechanical and thermal properties of the nanocomposites were measured as a function of t-CNF content. Effect of acid treated CNFs on to the mechanical properties of epoxy nanocomposites was justified by comparing the mechanical properties of epoxy/t-CNF and epoxy/u-CNF nanocomposites with same loading level. The electrical conductivity was achieved by epoxy resin with a threshold at 1 wt % of t-CNF. Substantial improvement in thermal, mechanical and electrical properties of the synthesized epoxy/t-CNF nanocomposites may be suitable for fabricating electronic devices. - Highlights: • Epoxy/t-CNF nanocomposites are characterized by XRD, FTIR, SEM, AFM and TEM. • Electrical conductivity was achieved by epoxy with a threshold at 1 wt% of t-CNF. • Tensile strength is enhanced by 40% due to dispersion of t-CNF. • Synthesized nanocomposites are suitable for fabricating electronic devises.

  5. A rechargeable iodine-carbon battery that exploits ion intercalation and iodine redox chemistry.

    Science.gov (United States)

    Lu, Ke; Hu, Ziyu; Ma, Jizhen; Ma, Houyi; Dai, Liming; Zhang, Jintao

    2017-09-13

    Graphitic carbons have been used as conductive supports for developing rechargeable batteries. However, the classic ion intercalation in graphitic carbon has yet to be coupled with extrinsic redox reactions to develop rechargeable batteries. Herein, we demonstrate the preparation of a free-standing, flexible nitrogen and phosphorus co-doped hierarchically porous graphitic carbon for iodine loading by pyrolysis of polyaniline coated cellulose wiper. We find that heteroatoms could provide additional defect sites for encapsulating iodine while the porous carbon skeleton facilitates redox reactions of iodine and ion intercalation. The combination of ion intercalation with redox reactions of iodine allows for developing rechargeable iodine-carbon batteries free from the unsafe lithium/sodium metals, and hence eliminates the long-standing safety issue. The unique architecture of the hierarchically porous graphitic carbon with heteroatom doping not only provides suitable spaces for both iodine encapsulation and cation intercalation but also generates efficient electronic and ionic transport pathways, thus leading to enhanced performance.Carbon-based electrodes able to intercalate Li + and Na + ions have been exploited for high performing energy storage devices. Here, the authors combine the ion intercalation properties of porous graphitic carbons with the redox chemistry of iodine to produce iodine-carbon batteries with high reversible capacities.

  6. On-line determination of iodine in nuclear fuel reprocessing off-gas streams by a combination of laser-induced fluorimetry and laser photoacoustic spectroscopy

    International Nuclear Information System (INIS)

    Kuno, Yusuke; Sato, Souichi; Masui, Jinichi

    1992-01-01

    The on-line determination of molecular iodine and organic iodides in nuclear fuel reprocessing off-gas streams containing high concentrations of NO x gas was studied. Ultraviolet radiation is used to convert organic iodides into molecular iodine. The approximate concentration of iodine before and after the photochemical conversion in the presence of NO x gas was first determined by laser-induced fluorimetry. NO 2 was determined by photoacoustic spectroscopy, correcting the acoustic signal due to iodine by using the approximate iodine concentration. NO was determined from the concentrations of NO 2 before and after the photoirradiation based on the photochemical fraction changes of NO and NO 2 . The quenching of the fluorimetry due to NO and NO 2 was finally corrected with the NO and NO 2 concentrations obtained. The detection limit of the proposed method is 10 nl 1 -1 . 7 figs., 2 tabs., 11 refs

  7. Thermo-curable epoxy systems for nanoimprint lithography

    International Nuclear Information System (INIS)

    Wu, Chun-Chang; Hsu, Steve Lien-Chung

    2010-01-01

    In this work, we have used solvent-free thermo-curable epoxy systems for low-pressure and moderate-temperature nanoimprint lithography (NIL). The curing kinetic parameters and conversion of diglycidyl ether of bisphenol A (DGEBA) resin with different ambient-cure 930 and 954 hardeners were studied by the isothermal DSC technique. They are useful for the study of epoxy resins in the imprinting application. The DGEBA/930 and DGEBA/954 epoxy resists can be imprinted to obtain high-density nano- and micro-scale patterns on a flexible indium tin oxide/poly(ethylene terephthalate) (ITO/PET) substrate. The DGEBA/930 epoxy resin is not only suitable for resist material, but also for plastic mold material. Highly dense nanometer patterns can be successfully imprinted using a UV-curable resist from the DGEBA/930 epoxy mold. Using the replicated DGEBA/930 epoxy mold instead of the expensive master can prevent brittle failure of the silicon molds in the NIL

  8. Effect of chronic douching with polyvinylpyrrolidone-iodine on iodine absorption and thyroid function

    International Nuclear Information System (INIS)

    Safran, M.; Braverman, L.E.

    1982-01-01

    Daily vaginal douching with polyvinylpyrrolidone-iodine in 12 euthyroid volunteers for 14 days resulted in a significant increase in serum total iodine concentration and urine iodine excretion. The increase in serum total iodine was associated with a marked decrease in 24-hour 123 I uptake by the thyroid and a small but significant increase in serum thyrotropin (TSH) concentration. However, values for serum TSH never rose above the normal range. No significant changes in serum thyroxine (T4), free T4 index (FTI), or triiodothyronine concentrations were observed, although serum T4 and FTI did decrease slightly during treatment. The findings suggest that iodine is absorbed across the vaginal mucosa and that the subsequent increase in serum total iodine does induce subtle increases in serum TSH concentration. There was no evidence, however, of overt hypothyroidism in these euthyroid women

  9. Fatigue life extension of epoxy materials using ultrafast epoxy-SbF5 healing system introduced by manual infiltration

    Directory of Open Access Journals (Sweden)

    X. J. Ye

    2015-03-01

    Full Text Available The present paper is devoted to the verification of the capability of epoxy-SbF5 system as a healing chemistry for rapidly retarding and/or arresting fatigue cracks in epoxy materials at room temperature. Owing to the very fast curing speed of epoxy catalyzed by SbF5, epoxy monomer and the hardener (ethanol solution of SbF5–ethanol complex are successively infiltrated into the fracture plane under cyclic loading during the tension-tension fatigue test. As a result, the mechanisms including hydrodynamic pressure crack tip shielding, polymeric wedge and adhesive bonding of the healing agent are revealed. It is found that the healing agent forms solidified wedge at the crack tip within 20 s after start of polymerization of the epoxy monomer, so that the highest healing effect is offered at the moment. The epoxy-SbF5 system proves to be effective in rapidly obstructing fatigue crack propagation (despite that its cured version has lower fracture toughness than the matrix, and satisfies the requirement of constructing fast self-healing polymeric materials.

  10. Iodine tablets and a nuclear accident

    International Nuclear Information System (INIS)

    Paile, W.

    1992-01-01

    Radioactive iodine is one of the major substances released during severe nuclear accidents. Radioactive iodine is easily gasified, and if present in fallout it can enter the lungs, and thereby the circulatory system, with the inhalation of air. Once in a body, radioactive iodine accumulates in the thyroid and may result in tumours in the thyroid and, in extreme cases, impaired thyroid function. Accumulation of radioactive iodine can be prevented by taking non-radioactive, 'cold' iodine as tablets. Iodine tablets dilute the radioactive iodine that has entered the body. A dose of iodine also paralyses the thyroid temporarily by saturating its iodine-carrying capacity. To be useful iodine tablets should be taken immediately when a radioactive emission has occurred. If the tablets are taken too early or too late, they give little protection. Iodine tablets should not be taken just to be on the safe side, since their use may involve harmful side effects. Dosing instructions should also be followed with care. (orig.)

  11. Iodine deficiency and nutrition in Scandinavia

    DEFF Research Database (Denmark)

    Manousou, Sofia; Dahl, Lisbeth; Heinsbaek Thuesen, Betina

    2017-01-01

    Iodine nutrition is a result of geological conditions, iodine fortification and monitoring strategies within a country together with the dietary habits of the population. This review summarizes the basis for the current iodine situation in the Scandinavian countries in order to identify gaps...... strategies have been used in Scandinavia to improve iodine nutrition. The major source of iodine is iodized salt in Sweden and from milk and dairy products in Norway. In Denmark, drinking water, milk, dairy products and iodized salt used in commercial production of bread are the important sources of iodine....... The current iodine status in Scandinavia is not optimal and action is ongoing to increase iodination in Denmark, where there is mild iodine deficiency in the general population. Data from all three countries indicate insufficient iodine nutrition during pregnancy and there is a need for data from children...

  12. Design and Analysis of Drive Shaft using Kevlar/Epoxy and Glass/Epoxy as a Composite Material

    Science.gov (United States)

    Karthikeyan, P.; Gobinath, R.; Kumar, L. Ajith; Jenish, D. Xavier

    2017-05-01

    In automobile industry drive shaft is one of the most important components to transmit power form the engine to rear wheel through the differential gear. Generally steel drive shaft is used in automobile industry, nowadays they are more interested to replace steel drive shaft with that of composite drive shaft. The overall objective of this paper is to analyze the composite drive shaft using to find out the best replacement for conventional steel drive shaft. The uses of advanced composite materials such as Kevlar, Graphite, Carbon and Glass with proper resins ware resulted in remarkable achievements in automobile industry because of its greater specific strength and specific modulus, improved fatigue and corrosion resistances and reduction in energy requirements due to reduction in weight as compared to steel shaft. This paper is to presents, the modeling and analysis of drive shaft using Kevlar/Epoxy and Glass/Epoxy as a composite material and to find best replacement for conventional steel drive shafts with an Kevlar/epoxy or Glass/Epoxy resin composite drive shaft. Modeling is done using CATIA software and Analysis is carried out by using ANSYS 10.0 software for easy understanding. The composite drive shaft reduces the weight by 81.67 % for Kevlar/Epoxy and 72.66% for Glass/Epoxy when compared with conventional steel drive shaft.

  13. Iodine requirements and the risks and benefits of correcting iodine deficiency in populations

    NARCIS (Netherlands)

    Zimmermann, M.B.

    2008-01-01

    Iodine deficiency has multiple adverse effects on growth and development due to inadequate thyroid hormone production that are termed the iodine deficiency disorders (IDD). IDD remains the most common cause of preventable mental impairment worldwide. IDD assessment methods include urinary iodine

  14. Volatilization of iodine from vegetation

    International Nuclear Information System (INIS)

    Amiro, B.D.; Johnston, F.L.

    1989-01-01

    Gaseous emissions of iodine were measured from bean plant foliage. A gamma-emitting iodine tracer, Na 125 I, was taken up by the plants from a hydroponic growth medium and released to a cuvette atmosphere. The dynamics of the flux were studied using a flow-through gamma detector. The relationship between leaf radioactive tracer activity and growth-medium activity was linear, as was the relationship between the iodine flux and both leaf and growth-medium activity. Iodine flux and leaf conductance to water responded similarly to changes in light levels, suggesting that the stomata may partially control the flux. The flux was inhibited by aeration of the hydroponic growth media, and we postulate that methylation causes the iodine flux. Iodine emissions from living vegetation probably contribute < 0.1% to the stable iodine concentration in the atmosphere above terrestrial areas. However, this pathway may be a direct route for radioactive iodine transport from contaminated soils to the atmosphere. (author)

  15. Volatilization of iodine from vegetation

    Energy Technology Data Exchange (ETDEWEB)

    Amiro, B D; Johnston, F L [Atomic Energy of Canada Ltd., Pinawa, MB (Canada). Whiteshell Nuclear Research Establishment

    1989-01-01

    Gaseous emissions of iodine were measured from bean plant foliage. A gamma-emitting iodine tracer, Na {sup 125}I, was taken up by the plants from a hydroponic growth medium and released to a cuvette atmosphere. The dynamics of the flux were studied using a flow-through gamma detector. The relationship between leaf radioactive tracer activity and growth-medium activity was linear, as was the relationship between the iodine flux and both leaf and growth-medium activity. Iodine flux and leaf conductance to water responded similarly to changes in light levels, suggesting that the stomata may partially control the flux. The flux was inhibited by aeration of the hydroponic growth media, and we postulate that methylation causes the iodine flux. Iodine emissions from living vegetation probably contribute < 0.1% to the stable iodine concentration in the atmosphere above terrestrial areas. However, this pathway may be a direct route for radioactive iodine transport from contaminated soils to the atmosphere. (author).

  16. The Status of Iodine Nutrition and Iodine Deficiency Disorders ...

    African Journals Online (AJOL)

    Background: Iodine deficiency disorders are serious public health problems in Ethiopia. The aim of this study was to measure the prevalence and severity of iodine deficiency disorders among school children in Metekel Zone. Methods: A cross-sectional school based descriptive study was conducted between February 2011 ...

  17. Study and development of methodology for radioactive iodine fixation in polymeric substrate for manufacturing sources used in brachytherapy

    International Nuclear Information System (INIS)

    Rodrigues, Bruna T.; Souza, Carla D.; Benega, Marcos A.G. and others

    2014-01-01

    According global estimates of Globocan 2012 project of the International Agency for Research of Cancer, of the World Health Organization, there were 14,1 million new cases of cancer and a total of 8,2 million deaths from cancer. Also show that in 2030, the overall load will be 21,4 million new cases and 13,2 million cancer deaths. One of the prostate cancer therapy is brachytherapy, used in early and middle stages of the disease. It is made with the introduction of seeds with radioactive material within the tumor or in nearby regions, affecting the minimum surrounding tissues. The aim of this work is the study and developing the deposition of radioactive iodine on the polymeric substrate method, and an analysis relating the efficiency of the method to implementation in the laboratory of brachytherapy from IPEN. Iodine-125 is adsorbed on an epoxy resin solution. The objective of this study is to offer a new proposal for seeds. The results will give the data for the radiation protection and the procedures for radioactive waste management

  18. Iodine filters in nuclear installations

    International Nuclear Information System (INIS)

    Wilhelm, J.G.

    1982-01-01

    The present report discusses the significance for environmental exposure of the iodine released with the gaseous effluents of nuclear power stations and reprocessing plants in relation to releases of other airborne radionuclides. Iodine filtration processes are described. The release pathways and the composition of airborne fission product iodine mixtures and their bearing on environmental exposure are discussed on the basis of measured fission product iodine emissions. The sorbents which can be used for iodine filtration, their removal efficiencies and range of applications are dealt with in detail. The particular conditions governing iodine removal, which are determined by the various gaseous iodine species, are illustrated on the basis of experimentally determined retention profiles. Particular attention is given to the limitations imposed by temperature, humidity, radiation and filter poisoning. The types of filter normally used are described, their advantages and drawbacks discussed, the principles underlying their design are outlined and the sources of error indicated. The methods normally applied to test the efficiency of various iodine sorbents are described and assessed. Operating experience with iodine filters, gathered from surveillance periods of many years, is supplemented by a large number of test results and the findings of extensive experiments. Possible ways of prolonging the permissible service lives of iodine filters are discussed and information is given on protective measures. The various iodine removal processes applied in reprocessing plants are described and compared with reference to efficiency and cost. The latest developments in filter technology in reprocessing plants are briefly outlined

  19. Methylisothiazolinone and benzisothiazolinone are widely used in paint: a multicentre study of paints from five European countries

    DEFF Research Database (Denmark)

    Schwensen, Jakob F; Lundov, Michael; Bossi, Rossana

    2015-01-01

    were found in paints from all five countries. Paints purchased in Denmark and Sweden contained especially high concentrations of BIT. CONCLUSION: The use of MI across European countries is extensive. In view of the ongoing epidemic of MI contact allergy, an evaluation of the safety of MI in paints......BACKGROUND: In view of the current epidemic of contact allergy to methylisothiazolinone (MI), it is important to clarify the extent of use of MI and related isothiazolinones in paints currently available for the consumer and worker in Europe. OBJECTIVES: To elucidate the use and concentrations...... of MI, methylchloroisothiazolinone (MCI) and benzisothiazolinone (BIT) in paints on the European retail market. METHODS: Wall paints (n = 71) were randomly purchased in retail outlets in five European countries. The paints were quantitatively analysed for their contents of MI, MCI and BIT by high...

  20. Preparation of Microcellular Epoxy Foams through a Limited-Foaming Process: A Contradiction with the Time-Temperature-Transformation Cure Diagram.

    Science.gov (United States)

    Wang, Lijun; Zhang, Chun; Gong, Wei; Ji, Yubi; Qin, Shuhao; He, Li

    2018-01-01

    3D cross-linking networks are generated through chemical reactions between thermosetting epoxy resin and hardener during curing. The curing degree of epoxy material can be increased by increasing curing temperature and/or time. The epoxy material must then be fully cured through a postcuring process to optimize its material characteristics. Here, a limited-foaming method is introduced for the preparation of microcellular epoxy foams (Lim-foams) with improved cell morphology, high thermal expansion coefficient, and good compressive properties. Lim-foams exhibit a lower glass transition temperature (T g ) and curing degree than epoxy foams fabricated through free-foaming process (Fre-foams). Surprisingly, however, the T g of Lim-foams is unaffected by postcuring temperature and time. This phenomenon, which is related to high gas pressure in the bubbles, contradicts that indicated by the time-temperature-transformation cure diagram. High bubble pressure promotes the movement of molecular chains under heating at low temperature and simultaneously suppresses the etherification cross-linking reaction during post-curing. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Generation of atomic iodine via fluorine for chemical oxygen-iodine laser

    International Nuclear Information System (INIS)

    Jirasek, Vit; Spalek, Otomar; Censky, Miroslav; Pickova, Irena; Kodymova, Jarmila; Jakubec, Ivo

    2007-01-01

    A method of the chemical generation of atomic iodine for a chemical oxygen-iodine laser (COIL) using atomic fluorine as a reaction intermediate was studied experimentally. This method is based on the reaction between F 2 and NO providing F atoms, and the reaction of F with HI resulting in iodine atoms generation. Atomic iodine was produced with efficiency exceeding 40% relative to initial F 2 flow rate. This efficiency was nearly independent on pressure and total gas flow rate. The F atoms were stable in the reactor up to 2 ms. An optimum ratio of the reactants flow rates was F 2 :NO:HI = 1:1:1. A rate constant of the reaction of F 2 with HI was determined. The numerical modelling showed that remaining HI and IF were probably consumed in their mutual reaction. The reaction system was found suitable for employing in a generator of atomic iodine with its subsequent injection into a supersonic nozzle of a COIL

  2. Comparison of structural health assessment capabilities in epoxy – carbon black and epoxy – carbon nanotube nanocomposites

    Directory of Open Access Journals (Sweden)

    F. Inam

    2014-01-01

    Full Text Available A novel method for comparing structural health of different types of brittle epoxy nanocomposites filled with carbon nanostructured fillers is presented. Epoxy – 0.2 vol% carbon black (CB and epoxy – 0.2 vol% carbon nanotube (CNT nanocomposite bars were prepared by calendering and thermal curing. Nanocomposite bars were subjected to Vickers diamond indentation to produce sub-surface damage. Electrical conductivities were analysed by 4-point method to estimate the structural damage caused by indentation. For comprehensive comparison, fracture toughness and percolation threshold were analysed as well. Because of the systematically induced indentation damage, a sharp decrease of 89% was observed in the electrical conductivity of epoxy – CNT nanocomposite as compared to 25% in the electrical conductivity of epoxy – CB nanocomposite. CNTs impart superior damage sensing capability in brittle nanocomposite structures, in comparison to CB, due to their high aspect ratio (fibrous nature and high electrical conductivity.

  3. Formulation of eb-curable epoxy resin : some important parameters

    International Nuclear Information System (INIS)

    Dahlan bin Haji Mohd; Hosoi, Fumio; Sasaki, Takashi

    1989-01-01

    The works on the electron-beam curing of surface coatings using epoxy acrylic-based resins were discussed. The works covered among other things the effect of molecular weights of the resins on the physical properties of coatings and their physical and chemical characterizations. The emphasis was given to formulating the resins applicable to surface coatings. Curings were done on a low-energy electron beam accelerator operating at 250 kV. A number of parameters deemed important to formulations, such as the molecular weights of the oligomers and monomers, monomer ratios, and HEA additions were explored. It was found that one could modify the physical properties of the coatings by changing or adjusting those parameters. (author)

  4. Breastfeeding and maternal and infant iodine nutrition.

    Science.gov (United States)

    Azizi, Fereidoun; Smyth, Peter

    2009-05-01

    The aim of this review is to explore information available regarding iodine secretion in milk, both mothers and infants iodine nutrition during breastfeeding and to make recommendations for appropriate iodine supplementation during lactation. MEDLINE was queried for studies between 1960 and 2007 that included lactation and breastfeeding with iodine and iodine deficiency. Studies were selected if they studied (i) Secretion of iodine in breast milk; (ii) breastfeeding and iodine nutrition; (iii) factors affecting maternal iodine metabolism and (iv) recommendations for iodine supplementation during breastfeeding. Thirty-six articles met the selection criteria. The iodine content of breast milk varies with dietary iodine intake, being lowest in areas of iodine deficiency with high prevalence of goitre. Milk iodine levels are correspondingly higher when programs of iodine prophylaxis such as salt iodization or administration of iodized oil have been introduced. The small iodine pool of the neonatal thyroid turns over very rapidly and is highly sensitive to variations in dietary iodine intake. Expression of the sodium iodide symporter is up-regulated in the lactating mammary gland which results in preferential uptake of iodide. In areas of iodine sufficiency breast milk iodine concentration should be in the range of 100-150 microg/dl. Studies from France, Germany, Belgium, Sweden, Spain, Italy, Denmark, Thailand and Zaire have shown breast milk concentrations of nutrition. The current WHO/ICCIDD/UNICEF recommendation for daily iodine intake (250 microg for lactating mothers) has been selected to ensure that iodine deficiency dose not occur in the postpartum period and that the iodine content of the milk is sufficient for the infant's iodine requirement.

  5. Fracture behavior of α-zirconium phosphate-based epoxy nanocomposites

    International Nuclear Information System (INIS)

    Sue, H.-J.; Gam, K.T.; Bestaoui, N.; Clearfield, A.; Miyamoto, M.; Miyatake, N.

    2004-01-01

    The fracture behaviors of α-zirconium phosphate (α-ZrP) based epoxy nanocomposites, with and without core-shell rubber (CSR) toughening, were investigated. The state of exfoliation and dispersion of α-ZrP nanofiller in epoxy were characterized using X-ray scattering and various microscopy tools. The level of enhancement in storage moduli of epoxy nanocomposite against neat epoxy is found to depend on the state of exfoliation of α-ZrP as well as the damping characteristics of the epoxy matrix. The fracture process in epoxy nanocomposite is dominated by preferred crack propagation along the weak intercalated α-ZrP interfaces, and the presence of α-ZrP does not alter the fracture toughness of the epoxy matrix. However, the toughening using CSR can significantly improve the fracture toughness of the nanocomposite. The fracture mechanisms responsible for such a toughening effect in CSR-toughened epoxy nanocomposite are rubber particle cavitation, followed by shear banding of epoxy matrix. The ductility and toughenability of epoxy do not appear to be affected by the incorporation of α-ZrP. Approaches for producing toughened high performance polymer nanocomposites are discussed

  6. Paintings - high-energy protons detect pigments and paint-layers

    International Nuclear Information System (INIS)

    Denker, A.; Opitz-Coutureau, J.

    2004-01-01

    High-energy PIXE was used to identify pigment composition, sequencing and the thickness of paint-layers. Before applying the technique to valuable masterpieces, mock-ups were examined in a collaboration with the Kunsthistorisches Museum, Vienna. The results of high-energy PIXE were compared to conventional cross-section analysis. In addition, the non-destructiveness of the technique was investigated thoroughly. After this preparative work, two ancient paintings have been examined and the results are presented in this paper

  7. Historical origins of Petrykivsky decorative painting

    Directory of Open Access Journals (Sweden)

    T. A. Harkava

    2017-07-01

    Full Text Available Petrykivsky decorative painting is a part of Ukrainian folk art. Domestic science of folk art has originated and has been developing primarily as a study of archaeological antiquities and artistic monuments of the past. Scientific papers, which comprehended the process of folk art development, began to appear in the late nineteenth century, Archaeological Congresses became the impetus for their appearance. Being a representative of the decorative painting, Petrikivsky decorative painting is rooted by its murals to Tripoli. It was created as a peasant domestic drawing. Inexhaustible diversity of local variants of Petrikivsky decorative painting, its evolutionary change, the individual characteristics of paintings of hundreds of famous Ukrainian artists do not even allow comparing it to any other European counterparts, each of which is characterized only by some individual techniques. Petrikivsky decorative painting got the significant boost in its distribution and development when it «came down» from walls to paper. Paper pictures - malyovky - were stucked to walls following the traditional rules of domestic interior’s decoration. Petrikivsky decorative painting got the official status in 1913, when E. Evenbah, by the initiative of D.I. Yavornytsky, gathered the collection of Petrikivsky decorative painting’s malyovkas and organized the exhibition in St. Petersburg. Motives of painting are rooted into the local flora and fauna and into the historical tradition. However, Petrikivsky decorative painting is not a direct reflection of natural motifs. World, created in paintings, is the product of the imagination of folk artist, it is the stylization of local flowers, fruits and birds. First names of Masters of Petrikivsky decorative painting, which appeared in historical sources, were T. Pata, N. Bilokin, I. Pavlenko. Their official recognition happened in 1930 after their participation in the first republican exhibition, which was later shown

  8. Radiation safety in radioluminous paint workshop handling tritium activated paint

    International Nuclear Information System (INIS)

    Gaur, P.K.; Venkateswaran, T.V.

    1986-01-01

    This paper discusses the safety features related to a workshop when tritium activated luminous paint is handled by workmen. Salient features of the workshop and the methods employed for monitoring the radiation levels are briefly outlined and results are discussed. The importance of proper ventilation of the workplace and precautions to be taken in the storage of painted articles are highlighted. (author). 1 table, 3 figs

  9. Environmental Degradation and Durability of Epoxy-Clay Nanocomposites

    Directory of Open Access Journals (Sweden)

    Raman P. Singh

    2010-01-01

    Full Text Available This experimental investigation reports on the durability of epoxy-clay nanocomposites upon exposure to multiple environments. Nanocomposites are fabricated by mixing the clay particles using various combinations of mechanical mixing, high-shear dispersion, and ultrasonication. Clay morphology is characterized using X-ray diffraction and transmission electron microscopy. Specimens of both neat epoxy and the epoxy-clay nanocomposite are subjected to two environmental conditions: combined UV radiation and condensation on 3-hour repeat cycle and constant temperature-humidity, for a total exposure duration of 4770 hours. The presence of nanoscale clay inhibits moisture uptake, as demonstrated by exposure to constant temperature-humidity. Nonetheless, both materials lose mass under exposure to combined UV radiation and condensation due to the erosion of epoxy by a synergistic process. Surprisingly, the epoxy-clay specimens exhibit greater mass loss, as compared to neat epoxy. Mechanical testing shows that either environment does not significant affect the flexure modulus of either material. On the other hand, both materials undergo degradation in flexural strength when exposed to either environment. However, the epoxy-clay nanocomposite retains 37% more flexure strength than the neat epoxy after 4072 hours of exposure.

  10. Environmental Degradation and Durability of Epoxy-Clay Nanocomposites

    International Nuclear Information System (INIS)

    Singh, R.P.; Zunjarrao, S.C.; Pandey, G.; Khait, M.; Korach, C.S.

    2010-01-01

    This experimental investigation reports on the durability of epoxy-clay nanocomposites upon exposure to multiple environments. Nanocomposites are fabricated by mixing the clay particles using various combinations of mechanical mixing, high-shear dispersion, and ultrasonication. Clay morphology is characterized using X-ray diffraction and transmission electron microscopy. Specimens of both neat epoxy and the epoxy-clay nanocomposite are subjected to two environmental conditions: combined UV radiation and condensation on 3-hour repeat cycle and constant temperature-humidity, for a total exposure duration of 4770 hours. The presence of nanoscale clay inhibits moisture uptake, as demonstrated by exposure to constant temperature-humidity. Nonetheless, both materials lose mass under exposure to combined UV radiation and condensation due to the erosion of epoxy by a synergistic process. Surprisingly, the epoxy-clay specimens exhibit greater mass loss, as compared to neat epoxy. Mechanical testing shows that either environment does not significant affect the flexure modulus of either material. On the other hand, both materials undergo degradation in flexural strength when exposed to either environment. However, the epoxy-clay nanocomposite retains 37% more flexure strength than the neat epoxy after 4072 hours of exposure.

  11. Occupational exposure to epoxy resins

    NARCIS (Netherlands)

    Terwoert, J.; Kersting, K.

    2014-01-01

    Products based on epoxy resins as a binder have become popular in various settings, among which the construction industry and in windmill blade production, as a result of their excellent technical properties. However, due to the same properties epoxy products are a notorious cause of allergic skin

  12. Optimal buffer gas pressure for laser-induced fluorescence detection of the iodine-129 isotope in the atmosphere

    International Nuclear Information System (INIS)

    Kireev, S.V.; Pit'ko, A.V.; Shnyrev, S.L.

    1995-01-01

    The effect of atmospheric air pressure on the intensity of iodine-129 vapor fluorescence excited by a He-Ne (633 nm) laser is studied. It is shown that to achieve the maximum intensity of fluorescence of molecular iodine-129, it is advantageous, first, to use a 3 He- 20 Ne laser for excitation, and second, to detect atmospheric iodine impurities in the gas mixture under analysis evacuated to 2 x 10 18 - 4 x 10 18 mol/cm 3 . In this case, the sensitivity increases about twofold. 7 refs., 4 figs

  13. An Assessment of the Selenium Status of Iodine-Deficient and Non-Iodine Deficient Filipino Children

    Directory of Open Access Journals (Sweden)

    Ma. Sofia Amarra

    2002-06-01

    Full Text Available The aim of this study is to examine and compare blood selenium levels in iodine-deficient and non-iodine deficient children. Two groups of children were examined: one group with iodine deficiency (n=31 and the other group with normal iodine status (n=32. Blood was extracted by venipuncture from children aged 6-10 years attending first grade in Commonwealth Elementary School in Quezon City. Whole blood selenium was examined by electrothermal atomic absorption spectrophotometry (AAS. Iodine status was determined by goiter palpation and urinary iodine excretion. Mean selenium levels of deficient and non-deficient children were compared using T-test. Using a cut-off value of 60 mg Se/L whole blood, the proportion of children with normal and deficient iodine status who fell below this cut-off was compared using chi-square test. Whole blood selenium values ranged from 17.6 to 133.6 mg/L. There were no significant differences in mean selenium levels between children with normal and deficient iodine status. Children with normal iodine status had a mean blood selenium level of 55.87 ± 26.3 mg/L while children with deficient iodine status had a mean level of 58.76 ± 26.4 mg/L. Sixty percent of children had blood selenium levels below the arbitrary cut-off of 60 mg/L with no significant difference between groups (p = 0.165, indicating that selenium deficiency is prevalent in this group of children regardless of iodine status. Since selenium deficiency limits the response to iodine supplementation, further investigation is needed to determine whether the same situation exists in children from other areas.

  14. Comparison of structural health assessment capabilities in epoxy – carbon black and epoxy – carbon nanotube nanocomposites

    OpenAIRE

    F. Inam; B. R. Bhat; N. Luhyna; T. Vo

    2014-01-01

    A novel method for comparing structural health of different types of brittle epoxy nanocomposites filled with carbon nanostructured fillers is presented. Epoxy – 0.2 vol% carbon black (CB) and epoxy – 0.2 vol% carbon nanotube (CNT) nanocomposite bars were prepared by calendering and thermal curing. Nanocomposite bars were subjected to Vickers diamond indentation to produce sub-surface damage. Electrical conductivities were analysed by 4-point method to estimate the structural damage caused by...

  15. Iodine removal from a gas phase

    International Nuclear Information System (INIS)

    Vikis, A. Ch.

    1982-01-01

    Iodine, e.g. radioactive iodine, present as one or more organic iodides, optionally with elemental iodine, in a gas phase (e.g. air) are removed by photochemically decomposing the organic iodides to elemental iodine, reacting the iodine produced, and any initially present with excess ozone, preferably photochemically produced in situ in the gas phase to produce solid iodine oxides, and removing the solid oxides from the gas phase. (author)

  16. Iodine removal from a gas phase

    International Nuclear Information System (INIS)

    Vikis, A.C.

    1984-01-01

    Iodine, e.g. radioactive iodine, present as one or more organic iodides, optionally with elemental iodine, in a gas phase (e.g. air) are removed by photochemically decomposing the organic iodides to elemental iodine, reacting the iodine produced, and any initially present with excess ozone, preferably photochemically produced in situ in the gas phase to produce solid iodine oxides, and removing the solid oxides from the gas phase

  17. Biobased Epoxy Nanocomposites Derived from Lignin-Based Monomers.

    Science.gov (United States)

    Zhao, Shou; Abu-Omar, Mahdi M

    2015-07-13

    Biobased epoxy nanocomposites were synthesized based on 2-methoxy-4-propylphenol (dihydroeugenol, DHE), a molecule that has been obtained from the lignin component of biomass. To increase the content of hydroxyl groups, DHE was o-demethylated using aqueous HBr to yield propylcatechol (DHEO), which was subsequently glycidylated to epoxy monomer. Optimal conditions in terms of yield and epoxy equivalent weight were found to be 60 °C with equal NaOH/phenolic hydroxyl molar ratio. The structural evolution from DHE to cured epoxy was followed by (1)H NMR and Fourier transform infrared spectroscopy. The nano-montmorillonite modified DHEO epoxy exhibited improved storage modulus and thermal stability as determined from dynamic mechanical analysis and thermogravimetric analysis. This study widens the synthesis routes of biobased epoxy thermosets from lignin-based molecules.

  18. Determination of iodide, iodate and organo-iodine in waters with a new total organic iodine measurement approach.

    Science.gov (United States)

    Gong, Tingting; Zhang, Xiangru

    2013-11-01

    The dissolved iodine species that dominate aquatic systems are iodide, iodate and organo-iodine. These species may undergo transformation to one another and thus affect the formation of iodinated disinfection byproducts during disinfection of drinking waters or wastewater effluents. In this study, a fast, sensitive and accurate method for determining these iodine species in waters was developed by derivatizing iodide and iodate to organic iodine and measuring organic iodine with a total organic iodine (TOI) measurement approach. Within this method, organo-iodine was determined directly by TOI measurement; iodide was oxidized by monochloramine to hypoiodous acid and then hypoiodous acid reacted with phenol to form organic iodine, which was determined by TOI measurement; iodate was reduced by ascorbic acid to iodide and then determined as iodide. The quantitation limit of organo-iodine or sum of organo-iodine and iodide or sum of organo-iodine, iodide and iodate was 5 μg/L as I for a 40 mL water sample (or 2.5 μg/L as I for an 80 mL water sample, or 1.25 μg/L as I for a 160 mL water sample). This method was successfully applied to the determination of iodide, iodate and organo-iodine in a variety of water samples, including tap water, seawater, urine and wastewater. The recoveries of iodide, iodate and organo-iodine were 91-109%, 90-108% and 91-108%, respectively. The concentrations and distributions of iodine species in different water samples were obtained and compared. Copyright © 2013 Elsevier Ltd. All rights reserved.

  19. EPR and rheological study of hybrid interfaces in gold-clay-epoxy nanocomposites.

    Science.gov (United States)

    Angelov, Verislav; Velichkova, Hristiana; Ivanov, Evgeni; Kotsilkova, Rumiana; Delville, Marie-Hélène; Cangiotti, Michela; Fattori, Alberto; Ottaviani, Maria Francesca

    2014-11-11

    With the aim to obtain new materials with special properties to be used in various industrial and biomedical applications, ternary "gold-clay-epoxy" nanocomposites and their nanodispersions were prepared using clay decorated with gold nanoparticles (AuNPs), at different gold contents. Nanocomposites structure was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). Rheology and electron paramagnetic resonance (EPR) techniques were used in order to evaluate the molecular dynamics in the nanodispersions, as well as dynamics at interfaces in the nanocomposites. The percolation threshold (i.e., the filler content related to the formation of long-range connectivity of particles in the dispersed media) of the gold nanoparticles was determined to be ϕp = 0.6 wt % at a fixed clay content of 3 wt %. The flow activation energy and the relaxation time spectrum illustrated the presence of interfacial interactions in the ternary nanodispersions around and above the percolation threshold of AuNPs; these interfacial interactions suppressed the global molecular dynamics. It was found that below ϕp the free epoxy polymer chains ratio dominated over the chains attracted on the gold surfaces; thus, the rheological behavior was not significantly changed by the presence of AuNPs. While, around and above ϕp, the amount of the bonded epoxy polymer chains on the gold surface was much higher than that of the free chains; thus, a substantial increase in the flow activation energy and shift in the spectra to higher relaxation times appeared. The EPR signals of the nanocomposites depended on the gold nanoparticle contents and the preparation procedure thus providing a fingerprint of the different nanostructures. The EPR results from spin probes indicated that the main effect of the gold nanoparticles above ϕp, was to form a more homogeneous, viscous and polar clay-epoxy mixture at the nanoparticle surface. The knowledge

  20. Femtosecond Time-Resolved Resonance-Enhanced CARS of Gaseous Iodine at Room Temperature

    International Nuclear Information System (INIS)

    He Ping; Fan Rong-Wei; Xia Yuan-Qin; Yu Xin; Chen De-Ying; Yao Yong

    2011-01-01

    Time-resolved resonance-enhanced coherent anti-Stokes Raman scattering (CARS) is applied to investigate molecular dynamics in gaseous iodine. 40 fs laser pulses are applied to create and monitor the high vibrational states of iodine at room temperature (corresponding to a vapor pressure as low as about 35 Pa) by femtosecond time-resolved CARS. Depending on the time delay between the probe pulse and the pump/Stokes pulse pairs, the high vibrational states both on the electronically ground states and the excited states can be detected as oscillations in the CARS transient signal. It is proved that the femtosecond time-resolved CARS technique is a promising candidate for investigating the molecular dynamics of a low concentration system and can be applied to environmental and atmospheric monitoring measurements. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

  1. Effects of diuretics on iodine uptake in non-toxic goitre: comparison with low-iodine diet

    Energy Technology Data Exchange (ETDEWEB)

    Kapucu, L.Ozlem; Azizoglu, Firat [Department of Nuclear Medicine, Gazi University, Ankara (Turkey); Ayvaz, Goksun; Karakoc, Ayhan [Department of Endocrinology, Gazi University, Ankara (Turkey)

    2003-09-01

    Low-iodine diet has been employed to achieve iodine depletion prior to radioiodine (RI) therapy. However, treatment with diuretics may be more effective than low-iodine diet in causing iodine depletion and subsequent increase in RI uptake by the thyroid. Fifty-five patients with non-toxic goitre were given 0.20 MBq RI p.o. on the first day of the study and thyroid uptake was measured. In 15 patients, a low-iodine diet was started and continued for 14 days. The remaining 40 patients received furosemide 40 mg/day orally for 5 days with an unrestricted diet. On the 15th day of the study, all patients were given 0.20 MBq RI p.o. and thyroid RI uptake was measured again. Additionally, 24-h urinary iodine excretion and RI clearance were measured on the 1st and 6th days in 21 patients from the furosemide group and on the 1st and 15th days in eight patients from the diet group. Furosemide administration led to a 58.40% increase in iodine uptake over the baseline value, which was significantly higher than the increase caused by low-iodine diet (17.22%) (P<0.0001). Urinary excretion of RI decreased in both groups similarly (furosemide, 29.45%; low-iodine diet, 21.06%; P=0.33). Iodine clearance also decreased in each group similarly (10.61% vs 7.53%, P=0.53). Treatment with furosemide prior to administration of RI increases the uptake of RI by the thyroid more effectively than does low-iodine diet. (orig.)

  2. Toughening Mechanisms in Silica-Filled Epoxy Nanocomposites

    Science.gov (United States)

    Patel, Binay S.

    Epoxies are widely used as underfill resins throughout the microelectronics industry to mechanically couple and protect various components of flip-chip assemblies. Generally rigid materials largely surround underfill resins. Improving the mechanical and thermal properties of epoxy resins to better match those of their rigid counterparts can help extend the service lifetime of flip-chip assemblies. Recently, researchers have demonstrated that silica nanoparticles are effective toughening agents for lightly-crosslinked epoxies. Improvements in the fracture toughness of silica-filled epoxy nanocomposites have primarily been attributed to two toughening mechanisms: particle debonding with subsequent void growth and matrix shear banding. Various attempts have been made to model the contribution of these toughening mechanisms to the overall fracture energy observed in silica-filled epoxy nanocomposites. However, disparities still exist between experimental and modeled fracture energy results. In this dissertation, the thermal, rheological and mechanical behavior of eight different types of silica-filled epoxy nanocomposites was investigated. Each nanocomposite consisted of up to 10 vol% of silica nanoparticles with particle sizes ranging from 20 nm to 200 nm, with a variety of surface treatments and particle structures. Fractographical analysis was conducted with new experimental approaches in order to accurately identify morphological evidence for each proposed toughening mechanism. Overall, three major insights into the fracture behavior of real world silica-filled epoxy nanocomposites were established. First, microcracking was observed as an essential toughening mechanism in silica-filled epoxy nanocomposites. Microcracking was observed on the surface and subsurface of fractured samples in each type of silica-filled epoxy nanocomposite. The additional toughening contribution of microcracking to overall fracture energy yielded excellent agreement between experimental

  3. Iodine content in bread and salt in Denmark after iodization and the influence on iodine intake

    DEFF Research Database (Denmark)

    Rasmussen, Lone Banke; Ovesen, Lars; Christensen, Tue

    2007-01-01

    Objective To measure the iodine content in bread and household salt in Denmark after mandatory iodine fortification was introduced and to estimate the increase in iodine intake due to the fortification. Design The iodine content in rye breads, wheat breads and salt samples was assessed. The incre......, and the current fortification level of salt ( 13 ppm) seems reasonable.......% of the rye breads and 90% of the wheat breads were iodized. The median iodine intake from bread increased by 25 ( 13-43) mu g/day and the total median iodine intake increased by 63 (36-104) mu g/day. Conclusions The fortification of bread and salt has resulted in a desirable increase in iodine intake...

  4. Highly Modified Cellulose Nanocrystals and Formation of Epoxy-CNC Nanocomposites.

    Science.gov (United States)

    Abraham, Eldho; Kam, Doron; Nevo, Yuval; Slattegard, Rikard; Rivkin, Amit; Lapidot, Shaul; Shoseyov, Oded

    2016-10-05

    This work presents an environmentally friendly, iodine-catalysed chemical modification method to generate highly hydrophobic, optically active cellulose nanocrystals (CNC). The high degree of ester substitution (DS=2.18), hydrophobicity, crystalline behaviour and optical activity of the generated acetylated CNC (Ac-CNC) were quantified by TEM, FTIR, solid 13C NMR, contact angle, XRD and POM analyses. Ac-CNC possessing substantial enhancement in thermal stability (16.8%) and forms thin films with interlayer distance of 50-150 nm, presenting cavities suitable for entrapping nano and micro particles. Generated Ac-CNC proved as an effective reinforcing agent in hydrophobic polymer matrices for fabricating high performance nanocomposites. When integrated at a very low weight percentage (0.5%) in an epoxy matrix, Ac-CNC provided for a 73% increase in tensile strength and a 98% increase in modulus, demonstrating its remarkable reinforcing potential and effective stress transfer behaviour. The method of modification and the unique properties of the modified CNC (hydrophobicity, crystallinity, reinforcing ability and optical activity) render them a novel bionanomaterial for a range of multipurpose applications.

  5. Hydrophobic Modification of Layered Clays and Compatibility for Epoxy Nanocomposites

    Directory of Open Access Journals (Sweden)

    Jiang-Jen Lin

    2010-04-01

    Full Text Available Recent studies on the intercalation and exfoliation of layered clays with polymeric intercalating agents involving poly(oxypropylene-amines and the particular uses for epoxy nanocomposites are reviewed. For intercalation, counter-ionic exchange reactions of clays including cationic layered silicates and anionic Al-Mg layered double hydroxide (LDH with polymeric organic ions afforded organoclays led to spatial interlayer expansion from 12 to 92 Å (X-ray diffraction as well as hydrophobic property. The inorganic clays of layered structure could be modified by the poly(oxypropyleneamine-salts as the intercalating agents with molecular weights ranging from 230 to 5,000 g/mol. Furthermore, natural montmorillonite (MMT clay could be exfoliated into thin layer silicate platelets (ca. 1 nm thickness in one step by using polymeric types of exfoliating agents. Different lateral dimensions of MMT, synthetic fluorinated Mica and LDH clays had been cured into epoxy nanocomposites. The hydrophobic amine-salt modification resulting in high spacing of layered or exfoliation of individual clay platelets is the most important factor for gaining significant improvements of properties. In particular, these modified clays were reported to gain significant improvements such as reduced coefficient of thermal expansion (CTE, enhanced thermal stability, and hardness. The utilization of these layered clays for initiating the epoxy self-polymerization was also reported to have a unique compatibility between clay and organic resin matrix. However, the matrix domain lacks of covalently bonded crosslink and leads to the isolation of powder material. It is generally concluded that the hydrophobic expansion of the clay inter-gallery spacing is the crucial step for enhancing the compatibility and the ultimate preparation of the advanced epoxy materials.

  6. Hydrophobic Modification of Layered Clays and Compatibility for Epoxy Nanocomposites

    Science.gov (United States)

    Lin, Jiang-Jen; Chan, Ying-Nan; Lan, Yi-Fen

    2010-01-01

    Recent studies on the intercalation and exfoliation of layered clays with polymeric intercalating agents involving poly(oxypropylene)-amines and the particular uses for epoxy nanocomposites are reviewed. For intercalation, counter-ionic exchange reactions of clays including cationic layered silicates and anionic Al-Mg layered double hydroxide (LDH) with polymeric organic ions afforded organoclays led to spatial interlayer expansion from 12 to 92 Å (X-ray diffraction) as well as hydrophobic property. The inorganic clays of layered structure could be modified by the poly(oxypropylene)amine-salts as the intercalating agents with molecular weights ranging from 230 to 5,000 g/mol. Furthermore, natural montmorillonite (MMT) clay could be exfoliated into thin layer silicate platelets (ca. 1 nm thickness) in one step by using polymeric types of exfoliating agents. Different lateral dimensions of MMT, synthetic fluorinated Mica and LDH clays had been cured into epoxy nanocomposites. The hydrophobic amine-salt modification resulting in high spacing of layered or exfoliation of individual clay platelets is the most important factor for gaining significant improvements of properties. In particular, these modified clays were reported to gain significant improvements such as reduced coefficient of thermal expansion (CTE), enhanced thermal stability, and hardness. The utilization of these layered clays for initiating the epoxy self-polymerization was also reported to have a unique compatibility between clay and organic resin matrix. However, the matrix domain lacks of covalently bonded crosslink and leads to the isolation of powder material. It is generally concluded that the hydrophobic expansion of the clay inter-gallery spacing is the crucial step for enhancing the compatibility and the ultimate preparation of the advanced epoxy materials.

  7. Mechanical properties of graphene oxide (GO/epoxy composites

    Directory of Open Access Journals (Sweden)

    Shivan Ismael Abdullah

    2015-08-01

    Full Text Available In this study, the effects of graphene oxide (GO on composites based on epoxy resin were analyzed. Different contents of GO (1.5–6 vol.% were added to epoxy resin. The GO/epoxy composite was prepared using the casting method and was prepared under room temperature. Mechanical tests’ results such as tensile test, impact test and hardness test show enhancements of the mechanical properties of the GO/epoxy composite. The experimental results clearly show an improvement in the Young’s modulus, tensile strength and hardness. The impact strength was seen to decrease, pointing to brittleness increase of the GO/epoxy composite. A microstructure analysis using Scanning Electron Microscopy (SEM and X-ray diffraction (XRD analysis was also performed, which showed how GO impeded the propagation of cracks in the composite. From the SEM images we observed the interface between the GO and the epoxy composite. As can be seen from this research, the GO/epoxy composites can be used for a large number of applications. The results of this research are a strong evidence for GO/epoxy composites being a potential candidate for use in a variety of industrial applications, especially for automobile parts, aircraft components, and electronic parts such as supercapacitors, transistors, etc.

  8. Modelling the chemistry of iodine

    International Nuclear Information System (INIS)

    Paquette, J.

    1989-01-01

    We have assembled a kinetic model, based on elementary chemical reactions, that describes the chemical behaviour of iodine in aqueous solution as a function of time and various parameters such as pH, concentration and radiation field. The model is conceptually divided into six section: aqueous iodine chemistry, aqueous organic iodide chemistry, water radiolysis, radiolysis of iodine solutions, radiolysis of organic iodide solutions and mass transfer. The model indicates that, in the absence of a radiation field, the rate of production of volatile iodine species is controlled by the rate of oxidation of the iodide ion. The volatile iodine species are dominated by organic iodides if organic impurities are present. The single most important parameter controlling iodine volatility is the pH of the solution; high pH values tend to minimize iodine volatility. In the presence of a radiation field, the volatility of iodine is controlled by the radiation-induced oxidation of the iodide ion. Again, iodine volatility is dominated by organic iodides if organic impurities are present. High pH values minimize iodine volatility. A sensitivity analysis has been performed on some sections of the model to identify reactions to which the volatility of iodine is most sensitive. In the absence of a radiation field, the volatility is most sensitive, first, to the rate of oxidation of the iodide ion, and, second, to the rate of mass transfer of volatile species between the aqueous and the gaseous phases. This approach should be useful in identifying reactions for which accurate rate constants are required and in decreasing the complexity of the model. 37 refs

  9. Iodine status in neonates in Denmark

    DEFF Research Database (Denmark)

    Nøhr, S B; Laurberg, Peter; Børlum, K G

    1994-01-01

    Iodine status of 147 neonates born in five different regions of Denmark was evaluated in relation to the iodine content of breast milk and iodine supplementation taken by the mother. Approximately two-thirds of the women had not received iodine supplementation. They had low iodine concentrations...... in breast milk and urinary iodine concentrations of the neonates at day 5 were low. The median values (milk/urine) were 33.6/31.7 micrograms/l (Randers 22/26, Ringkøbing 29/16, Aalborg 36/31. Arhus 54/41 and Copenhagen 55/59 micrograms/l). Higher values were found in the group where tablets containing...... iodine had been taken (milk/urine: 57.0/61.0 micrograms/l). In general, the values are low compared with internationally recommended levels. We suggest that mothers without autoimmune thyroid disease should receive iodine supplementation in the form of vitamin/mineral tablets containing iodine (150...

  10. Iodine bonding stabilizes iodomethane in MIDAS pesticide. Theoretical study of intermolecular interactions between iodomethane and chloropicrin.

    Science.gov (United States)

    Glaser, Rainer; Prugger, Kaitlan

    2012-02-22

    The results are reported of a theoretical study of iodomethane (H(3)C-I, 1) and chloropicrin (Cl(3)C-NO(2), 2), of the heterodimers 3-6 formed by aggregation of 1 and 2, and of their addition products 7 and 8 and their possible fragmentation reactions to 9-18. Mixtures of iodomethane and chloropicrin are not expected to show chemistry resulting from their reactions with each other. The structures and stabilities are discussed of the iodine-bonded molecular aggregates (IBMA) 3 and 4 and of the hydrogen- and iodine-bonded molecular aggregates (IHBMA) 5 and 6. The mixed aggregates 3-5 are bound on the free enthalpy surface relative to the homodimers of 1 and 2, and the IBMA structures 3 and 4 are most stable. This result suggests that the mixture of chloropicrin and iodomethane in the pesticide Midas is a good choice to reduce the volatility of iodomethane because of thermodynamically stabilizing iodine bonding.

  11. Effect of an organoclay on the reaction-induced phase-separation in a dynamically asymmetric epoxy/PCL system

    Directory of Open Access Journals (Sweden)

    J. Rotrekl

    2013-12-01

    Full Text Available The addition of layered silicates can significantly affect the phase behaviour of both immiscible thermoplastic blends and partially miscible thermoset systems that undergo reaction-induced phase separation (RIPS during curing. This study focuses on the phase behaviour of polycaprolactone (PCL/epoxy in the presence of organically modified montmorillonite (oMMT. Due to the high dynamic asymmetry caused by the differences in the molecular weights and viscosities of the PCL and the uncured epoxy, the critical point is localised at low PCL concentrations, as indicated by the pseudophase diagram. The addition of oMMT to the system led to the marked shift of the critical point towards higher concentrations of PCL, with an increase in the oMMT content occurring as a consequence of the preferential localisation of the clay in the epoxy phase, making this phase more dynamically slow. Significant changes in morphology, including phase inversion of the PCL/epoxy systems caused by the presence of oMMT, were recorded for PCL concentrations ranging from 10 to 30%.

  12. Mixed-layered bismuth--oxygen--iodine materials for capture and waste disposal of radioactive iodine

    Science.gov (United States)

    Krumhansl, James L; Nenoff, Tina M

    2015-01-06

    Materials and methods of synthesizing mixed-layered bismuth oxy-iodine materials, which can be synthesized in the presence of aqueous radioactive iodine species found in caustic solutions (e.g. NaOH or KOH). This technology provides a one-step process for both iodine sequestration and storage from nuclear fuel cycles. It results in materials that will be durable for repository conditions much like those found in Waste Isolation Pilot Plant (WIPP) and estimated for Yucca Mountain (YMP). By controlled reactant concentrations, optimized compositions of these mixed-layered bismuth oxy-iodine inorganic materials are produced that have both a high iodine weight percentage and a low solubility in groundwater environments.

  13. Mixed-layered bismuth-oxygen-iodine materials for capture and waste disposal of radioactive iodine

    Science.gov (United States)

    Krumhansl, James L; Nenoff, Tina M

    2013-02-26

    Materials and methods of synthesizing mixed-layered bismuth oxy-iodine materials, which can be synthesized in the presence of aqueous radioactive iodine species found in caustic solutions (e.g. NaOH or KOH). This technology provides a one-step process for both iodine sequestration and storage from nuclear fuel cycles. It results in materials that will be durable for repository conditions much like those found in Waste Isolation Pilot Plant (WIPP) and estimated for Yucca Mountain (YMP). By controlled reactant concentrations, optimized compositions of these mixed-layered bismuth oxy-iodine inorganic materials are produced that have both a high iodine weight percentage and a low solubility in groundwater environments.

  14. CHARACTERIZATION OF ALKALINE LIGNINS FOR USE IN PHENOL-FORMALDEHYDE AND EPOXY RESINS

    Directory of Open Access Journals (Sweden)

    Nour Eddine El Mansouri

    2011-05-01

    Full Text Available Besides polyurethanes and polyesters, phenolic and epoxy resins are the most prominent applications for technical lignins in thermosetting materials. To evaluate the potential application of lignin raw materials in phenol formaldehyde and epoxy resins, three types of alkaline lignins were characterized in terms of their structures and thermal properties. The lignin samples analyzed were kraft lignin (LIG-1, soda–rice straw lignin (LIG-2, and soda-wheat straw lignin (LIG-3. FTIR and 1H-NMR methods were used to determine their structure. Gel permeation chromatography (GPC was used to determine the molecular weight distribution (MWD. Differential scanning calorimetry (DSC was used to measure the glass transition temperature (Tg, and thermogravimetric analysis (TGA to determine the thermal stability of lignin samples. Results showed that kraft lignin (LIG-1 has moderate hydroxyl-group content, is rich in G-type units, and has good thermal stability. These properties make it more suitable for direct use in phenol formaldehyde resins, and it is therefore a good raw material for this purpose. The alkaline soda-rice straw lignin (LIG-2 with a high hydroxyl-group content and excellent thermal stability is most suited to preparing lignin-based epoxy resins.

  15. Removal of volatile iodine from gas bubbles rising in water pools: review and assessment of pool scrubbing codes

    Energy Technology Data Exchange (ETDEWEB)

    Polo, J; Herranz, L E; Peyres, V; Escudero, M [CIEMAT, Nuclear Technology Institute, Madrid (Spain)

    1996-12-01

    During a hypothetical nuclear reactor accident with core damage the fission products released from the degrading fuel bundles often pass through aqueous beds before entering the containment, mitigating in part the source term. Several computer codes have been developed for predicting the fission product and aerosols removal in pool scrubbing scenarios. In addition to particle removal, these codes simulate the retention of some volatile iodine compounds. In this work a review of volatile iodine removal models included in SPARC and BUSCA codes is presented. Besides, the results and discussions of a validation of both codes against the available experimental data are summarized. SPARC and BUSCA codes model the diffusion of iodine toward the bubble interface by using the film penetration theory, which assumes a double layer gas-liquid at the interface. However, there are some differences between the two models, mainly related to the boundary conditions in the aqueous volume for the diffusion of molecular iodine. In SPARC, a set of fast reactions in the liquid phase control both the molecular iodine concentration in the pool and the partition coefficient of iodine at the interface. Thus, the aqueous chemistry plays an important role in the boundary conditions for the diffusion process. On the contrary, the BUSCA model has no chemical considerations at all, and assumes a null iodine concentration in the water bulk. Several sensitivity studies have been made in order to weight the effect of these differences. The variables examined in these studies were the pool temperature and the incoming iodine concentration in the pool. Additionally, sensitivity studies focused on the steam mass fraction of the injected gas were performed to study the effect of the different approach of both models for the condensation process. The results showed a different sensitivity of SPARC and BUSCA to the incoming concentration. (author) 5 tabs., 26 refs.

  16. Cooperativity and binding isotherms of the amylose-iodine-triiodide complex

    International Nuclear Information System (INIS)

    Cesaro, A.; Benegas, J.C.; Ripoll, D.R.

    1984-08-01

    A simple model has been presented which is based on some widely accepted characteristics of the amylose-iodine-triiodide complex and is capable of correlating a number of experimental features with molecular parameters. A substantial improvement is obtained removing weakness and arbitrariness of some adjustable parameters of previous models. The proposed model assumes that sequences of bound species are initiated by triiodide ions and propagated (principally) by iodine. The theory is developed by using the matrix method of Zimm and Bragg and assuming that the cooperative interaction is of electrostatic nature. The model reproduces most of the experimental data and predicts a finite length of the bound polyiodine chain for any length of the host polymer. (author)

  17. Iodine in the environment revisited

    International Nuclear Information System (INIS)

    Christiansen, J.V.; Carlsen, L.

    1989-05-01

    The report gives an overview of the environmental cycle of iodine, especially focusing on the possible reactions being responsible for the retention of iodine in the terrestrial environment. During the last two decades evidence for the presence of iodine in soil as organically bound has been presented. The major part of inorganic iodine in the terrestrial environment will, under physical and chemical conditions normally prevailing, exist as iodide. No evidence for a direct reaction between iodide and organic material has been presented, whereas strong support for the engagement of microbial activity in the formation of organic iodine compounds in soil has been obtained. Incorporation of iodine in humic substances as a result of enzymatic catalysis, involving an enzyme of the perozidase group apperas reasonable. It is concluded that microbiological activity involving extracellular enzymes most probably is responsible for the possible retention of iodine in the terrestrial environment. It is suggested that these reactions in detail should be studied experimentally. (author) 3 tabs., 2 ills., 51 refs

  18. Iodine Intakes of Victorian Schoolchildren Measured Using 24-h Urinary Iodine Excretion

    Directory of Open Access Journals (Sweden)

    Kelsey Beckford

    2017-08-01

    Full Text Available Mandatory fortification of bread with iodized salt was introduced in Australia in 2009, and studies using spot urine collections conducted post fortification indicate that Australian schoolchildren are now replete. However an accurate estimate of daily iodine intake utilizing 24-h urinary iodine excretion (UIE μg/day has not been reported and compared to the estimated average requirement (EAR. This study aimed to assess daily total iodine intake and status of a sample of primary schoolchildren using 24-h urine samples. Victorian primary school children provided 24-h urine samples between 2011 and 2013, from which urinary iodine concentration (UIC, μg/L and total iodine excretion (UIE, μg/day as an estimate of intake was determined. Valid 24-h urine samples were provided by 650 children, mean (SD age 9.3 (1.8 years (n = 359 boys. The mean UIE of 4–8 and 9–13 year olds was 94 (48 and 111 (57 μg/24-h, respectively, with 29% and 26% having a UIE below the age-specific EAR. The median (IQR UIC was 124 (83,172 μg/L, with 36% of participants having a UIC < 100 μg/L. This convenience sample of Victorian schoolchildren were found to be iodine replete, based on UIC and estimated iodine intakes derived from 24-h urine collections, confirming the findings of the Australian Health Survey.

  19. Status of urinary iodine and I-131 uptake after universal iodination of common salt

    International Nuclear Information System (INIS)

    Alam, F.; Begum, F.; Haque, M.; Karim, M.A.; Faruque, O.; Ali, L.; Khan, A.K.A.

    2002-01-01

    This work was carried out in the Institute of Institute of Nuclear Medicine (INM), Bangabandhu Sheikh Mujib Medical University and Bangladesh Institute of Research and Rehabilitation in Diabetes, Endocrine and Metabolic Disorders, Dhaka. Here we have tried to explore present status of urinary iodine and uptake status in Bangabandhu. Period study was from 1998 to 2000. Total study population was 300, of them 84 was male and 216 was female. Populations of all social and economic strata have been studied, starting from bottoms to top-level income groups as well as urban, rural and suburban populations are included randomly. We studied I-131 uptake and urinary iodine. I-131 given orally in liquid form and the quantity accumulated by the thyroid gland at 24 hours intervals of time is measured using a gamma scintillation counter. Gamma-ray emission of 364 keV energy by I-131 is detected gamma scintillation counter. Urinary iodine is estimated by CIS-BIO kit. Urine is digested with chloric acid under mild conditions and determined manually by its catalytic role in the reduction of ceric ammonium sulfate in the presence of arsenious acid. The uptake was grouped into four categories according to their uptake percentage. Group-A; (lowest uptake group) 99 subject, have uptake between 0 to 4.9%, Group-B; 100 subjects, (relatively low uptake) who have uptake between 4.91-9.9%, group-C; 73 subjects, who have uptake between 10-30% and in-group D, there was 28 subjects their uptake was above 30%. We have also found in group-A median uptake is 3.0% and urinary iodine level is 43.31 μg/dl, in group-B median uptake is 7.0% and urinary iodine level is 33.95 μg/dl, in group-C median uptake is 23.0% and urinary iodine level is 12.97 μg/dl, in group-D median uptake is 34.0% and urinary iodine level is 9.35 μg/dl. We have found 1.04% have severe type low urinary iodine, 3.48% moderate type of low urinary iodine, 3.48%, 16.72% mild type of low urinary iodine and 78.74% have normal

  20. Activation energies for iodine-exchange systems containing organic iodine compounds

    Energy Technology Data Exchange (ETDEWEB)

    Ikeda, N. (Takyo Univ. of Education (Japan). Faculty of Science) Takahashi, Yasuko

    1976-01-01

    In studies on the nonequilibrium isotopic exchange method for determining iodine in organic iodine compounds, activation energies have been measured to find systems having appropriate rate of exchange reactions. Activation energies are discussed by considering the effect of the structure of organic iodine compounds, the concentrations of reactants and solvent, etc. In homogeneous systems, activation energy is found to become larger in the order of CH/sub 3/Iiodine ratio between I/sub 2/ and organic iodine is a predominant factor in determining the rate of the exchange reaction.

  1. Impact on the environment from steel bridge paint deterioration using lead isotopic tracing, paint compositions and soil deconstruction

    Energy Technology Data Exchange (ETDEWEB)

    Gulson, Brian, E-mail: brian.gulson@mq.edu.au [Department of Environmental Science, Macquarie University, Sydney, NSW 2109 (Australia); CSIRO Energy Flagship, North Ryde, NSW 2113 (Australia); Chiaradia, Massimo [Department of Mineralogy, University of Geneva, Geneva (Switzerland); Davis, Jeffrey [CSIRO Energy Flagship, North Ryde, NSW 2113 (Australia); O' Connor, Gary [Queensland Department of Environment & Heritage Protection, Brisbane, QLD 4000 (Australia)

    2016-04-15

    Deterioration and repair of lead paint on steel structures can result in contamination of the ambient environment but other sources of lead such as from past use of leaded paint and gasoline and industrial activities can also contribute to the contamination. Using a combination of high precision lead isotopic tracing, detailed paint examination, including with scanning electron microscopy, and soil deconstruction we have compared paint on a steel bridge and bulk soil and lead-rich particles separated from soil. The majority of Pb found in the paint derives from Australian sources but some also has a probable US origin. The isotopic data for the bulk soils and selected particles lie on a mixing line with end members the geologically ancient Broken Hill lead and possible European lead which is suggested to be derived from old lead paint and industrial activities. Data for gasoline-derived particulates lie on this array and probably contribute to soil Pb. Although paint from the bridge can be a source of lead in the soils, isotopic tracing, paint morphology and mineralogical identification indicate that other sources, including from paint, gasoline and industrial activities, are contributing factors to the lead burden. Even though physical characteristics and elemental composition are the same in some particles, the isotopic signatures demonstrate that the sources are different. Plots using {sup 206}Pb/{sup 208}Pb vs {sup 206}Pb/{sup 207}Pb ratios, the common representation these days, do not allow for source discrimination in this investigation. - Highlights: • Soil Pb values up to 1200 mg/kg below Pb painted bridge • Microscopy & SEM characterised up to 6 different paint layers. • Isotopes identified different sources of Pb including paint and gasoline. • Multiple methods provide definitive answers.

  2. Iodine filters in nuclear power stations

    International Nuclear Information System (INIS)

    Wilhelm, J.G.

    1977-04-01

    On the basis of calculated and recorded release rates of nuclear power plants, the significance of iodine releases in the invironmental impact relative to other nuclides is discussed. The release pathways for iodine in LWR-type reactors and the efficiency of various methods to lower the activity release are given. The airborne species of iodine are discussed with regard to their removal in iodine sorption filters and environmental impact. The technical status of iodine removal by means of iodine sorption filters is studied for normal operation and accident conditions in nuclear power stations on the basis of the data given in the relevant literature for the efficiency of a number of iodine sorption materials. The applicability of concepts for ventilation and containment and their influence on iodine filter systems are discussed. Design, structure, and testing of iodine sorption filters are treated in detail; recommendations for design are given, and failure sources are mentioned. (orig.) [de

  3. 24 CFR 35.1320 - Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and...

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Lead-based paint inspections, paint testing, risk assessments, lead-hazard screens, and reevaluations. 35.1320 Section 35.1320 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development LEAD-BASED PAINT...

  4. 75 FR 6383 - Lead-Based Paint Renovation, Repair and Painting, and Pre-Renovation Education Activities in...

    Science.gov (United States)

    2010-02-09

    ..., Repair and Painting, and Pre- Renovation Education Activities in Target Housing and Child Occupied....C. 2682(c)(3), and a lead-based paint pre-renovation education program in accordance with section... TSCA, and a lead-based paint pre-renovation education program in accordance with section 406(b) of TSCA...

  5. Iodine Satellite

    Science.gov (United States)

    Kamhawi, Hani; Dankanich, John; Martinez, Andres; Petro, Andrew

    2015-01-01

    The Iodine Satellite (iSat) spacecraft will be the first CubeSat to demonstrate high change in velocity from a primary propulsion system by using Hall thruster technology and iodine as a propellant. The mission will demonstrate CubeSat maneuverability, including plane change, altitude change and change in its closest approach to Earth to ensure atmospheric reentry in less than 90 days. The mission is planned for launch in fall 2017. Hall thruster technology is a type of electric propulsion. Electric propulsion uses electricity, typically from solar panels, to accelerate the propellant. Electric propulsion can accelerate propellant to 10 times higher velocities than traditional chemical propulsion systems, which significantly increases fuel efficiency. To enable the success of the propulsion subsystem, iSat will also demonstrate power management and thermal control capabilities well beyond the current state-of-the-art for spacecraft of its size. This technology is a viable primary propulsion system that can be used on small satellites ranging from about 22 pounds (10 kilograms) to more than 1,000 pounds (450 kilograms). iSat's fuel efficiency is ten times greater and its propulsion per volume is 100 times greater than current cold-gas systems and three times better than the same system operating on xenon. iSat's iodine propulsion system consists of a 200 watt (W) Hall thruster, a cathode, a tank to store solid iodine, a power processing unit (PPU) and the feed system to supply the iodine. This propulsion system is based on a 200 W Hall thruster developed by Busek Co. Inc., which was previously flown using xenon as the propellant. Several improvements have been made to the original system to include a compact PPU, targeting greater than 80 percent reduction in mass and volume of conventional PPU designs. The cathode technology is planned to enable heaterless cathode conditioning, significantly increasing total system efficiency. The feed system has been designed to

  6. Epoxy resin systems for FGD units

    International Nuclear Information System (INIS)

    Brytus, V.; Puglisi, J.S.

    1984-01-01

    This paper discusses ongoing research work which is directed towards epoxy resins and curing agents which are designed to withstand aggressive environments. This work includes not only a chemical description of the materials involved, but the application testing necessary to verify the usefulness of these systems. It demonstrates that new high performance epoxy systems are superior to those which traditionally come to mind when one thinks epoxy. Finally, it discusses the results of testing designed specifically to screen candidates for use in FGD units

  7. Preference for and discrimination of paintings by mice.

    Directory of Open Access Journals (Sweden)

    Shigeru Watanabe

    Full Text Available I measured preference for paintings (Renoir vs. Picasso or Kandinsky vs. Mondrian in mice. In general mice did not display a painting preference except for two mice: one preferred Renoir to Picasso, and the other preferred Kandinsky to Mondrian. Thereafter, I examined discrimination of paintings with new mice. When exposure to paintings of one artist was associated with an injection of morphine (3.0 mg/kg, mice displayed conditioned preference for those paintings, showing discrimination of paintings by Renoir from those by Picasso, and paintings by Kandinsky from those by Mondrian after the conditioning. They also exhibited generalization of the preference to novel paintings of the artists. After conditioning with morphine for a set of paintings consisting of two artists, mice showed discrimination between two sets of paintings also from the two artists but not in association with morphine. These results suggest that mice can discriminate not only between an artist's style but also among paintings of the same artist. When mice were trained to discriminate a pair of paintings by Kandinsky and Renoir in an operant chamber equipped with a touch screen, they showed transfer of the discrimination to new pairs of the artists, but did not show transfer of discrimination of paintings by other artists, suggesting generalization.

  8. Predissociation of high-lying Rydberg states of molecular iodine via ion-pair states

    Energy Technology Data Exchange (ETDEWEB)

    Bogomolov, Alexandr S. [Institute of Chemical Kinetics and Combustion, Institutskaya Str. 3, Novosibirsk 630090 (Russian Federation); Grüner, Barbara; Mudrich, Marcel [Physikalisches Institut, Universität Freiburg, D-79104 Freiburg (Germany); Kochubei, Sergei A. [Institute of Semiconductor Physics, ac. Lavrent' yev ave., 13, Novosibirsk 630090 (Russian Federation); Baklanov, Alexey V. [Institute of Chemical Kinetics and Combustion, Institutskaya Str. 3, Novosibirsk 630090 (Russian Federation); Novosibirsk State University, Pirogova Str. 2, Novosibirsk 630090 (Russian Federation)

    2014-03-28

    Velocity map imaging of the photofragments arising from two-photon photoexcitation of molecular iodine in the energy range 73 500–74 500 cm{sup −1} covering the bands of high-lying gerade Rydberg states [{sup 2}Π{sub 1/2}]{sub c}6d;0{sub g}{sup +} and [{sup 2}Π{sub 1/2}]{sub c}6d;2{sub g} has been applied. The ion signal was dominated by the atomic fragment ion I{sup +}. Up to 5 dissociation channels yielding I{sup +} ions with different kinetic energies were observed when the I{sub 2} molecule was excited within discrete peaks of Rydberg states and their satellites in this region. One of these channels gives rise to images of I{sup +} and I{sup −} ions with equal kinetic energy indicating predissociation of I{sub 2} via ion-pair states. The contribution of this channel was up to about 50% of the total I{sup +} signal. The four other channels correspond to predissociation via lower lying Rydberg states giving rise to excited iodine atoms providing I{sup +} ions by subsequent one-photon ionization by the same laser pulse. The ratio of these channels varied from peak to peak in the spectrum but their total ionic signal was always much higher than the signal of (2 + 1) resonance enhanced multi-photon ionization of I{sub 2}, which was previously considered to be the origin of ionic signal in this spectral range. The first-tier E0{sub g}{sup +} and D{sup ′}2{sub g} ion-pair states are concluded to be responsible for predissociation of Rydberg states [{sup 2}Π{sub 1/2}]{sub c}6d;0{sub g}{sup +} and [{sup 2}Π{sub 1/2}]{sub c}6d;2{sub g}, respectively. Further predissociation of these ion-pair states via lower lying Rydberg states gives rise to excited I(5s{sup 2}5p{sup 4}6s{sup 1}) atoms responsible for major part of ion signal. The isotropic angular distribution of the photofragment recoil directions observed for all channels indicates that the studied Rydberg states are long-lived compared with the rotational period of the I{sub 2} molecule.

  9. Long-term migration of iodine in sedimentary rocks based on iodine speciation and 129I/127I ratio

    Science.gov (United States)

    Togo, Y.; Takahashi, Y.; Amano, Y.; Matsuzaki, H.; Suzuki, Y.; Muramatsu, Y.; Iwatsuki, T.

    2012-12-01

    [Introduction] 129I is one of the available indexes of long-term migration of groundwater solutes, because of its long half-life (15.7 million years) and low sorption characteristics. The Horonobe underground research center (Japan Atomic Energy Agency), at which are conducted research and development of fundamental techniques on geological disposal of high-level radioactive waste, is an appropriate site for natural analogue studies, because iodine concentration in groundwater is high in this area. To predict iodine behavior in natural systems, speciation of iodine is essential because of different mobility among each species. In this study, we determined iodine speciation and129I/127I isotope ratios of rock and groundwater samples to investigate long term migration of iodine. [Methods] All rock and groundwater samples were collected at Horonobe underground research center. The region is underlain mainly by Neogene to Quaternary marine sedimentary rocks, the Wakkanai Formation (Wk Fm, siliceous mudstones), and the overlying Koetoi Formation (Kt Fm, diatomaceous mudstones). Iodine species in rock samples were determined by iodine K-edge X-ray absorption near edge structure (SPring-8 BL01B1). Thin sections of rock samples were prepared, and iodine mapping were obtained by micro-XRF analysis (SPring-8 BL37XU). Iodine species (IO3-, I-, and organic I) in groundwater were separately detected by high performance liquid chromatography connected to ICP-MS. The 129I/127I ratios in groundwater and rock samples were measured by accelerator mass spectrometry (MALT, Univ. of Tokyo). Iodine in rock samples were separated by pyrohydrolysis and water extraction. [Results and discussion] Concentration of iodine in groundwater varied widely and was much higher than that of seawater showing a high correlation with that of chlorine (R2 = 0.90). Species of iodine in groundwater was mainly I-. Iodine in rock samples decreased near the boundary between Wk and Kt Fms. Iodine K-edge XANES

  10. PAINT SUPPLIES AND LOCATION: EXAMINING ICI

    Directory of Open Access Journals (Sweden)

    M. Herron

    2016-01-01

    Full Text Available How important is location to an international retailer? Not just any retailer but the second largest paint retailer in the world. Imperial Chemical Industries (ICI was a British chemical company and was at one stage the largest manufacturer in Britain. Formed from the merger of several leading British chemical companies in 1926, ICI makes paints and speciality products, including food ingredients, speciality polymers, electronic materials, fragrances and flavourings. ICI paints purchased the Cleveland Ohiobased Glidden Coatings & Resins (Glidden Paint Company in 1986 for USD$580 million. The addition of Glidden to ICI's North American operations more than doubled that subsidiary's annual sales to $3 billion and increased ICI's corporate presence in the United States dramatically. A decline in paint and solvent consumption during the 2000 decade slowed the average growth of the paint industry to about 2% annually. Rauch Associates, the leading US paint analyst firm, predicted near-term growth to slow even further to 1.2% per annum. Through the 1990’s and early 2000’s Glidden paint was sold only through Glidden-badged paint stores and smaller retailers under licence, developing a strong identifiable brand and reputation. How were potential Glidden retail paint store locations chosen across America to enable and support this market growth? This paper investigates the real process that was developed and applied to construct a national network of retail outlets across the United States. It also highlights the change in direction that occurred at ICI paints culminating in its eventual acquisition by AkzoNobel in 2008 who immediately sold parts of ICI to Henkel, and integrated ICI's remaining operations within its existing organisation. This sale and the associated corporate restructure caused considerable change in marketing directions allowing for the first time the selling of Glidden paint products to mass market centres

  11. Serum thyroglobulin and urinary iodine concentration are the most appropriate indicators of iodine status and thyroid function under conditions of increasing iodine supply in schoolchildren in Benin

    NARCIS (Netherlands)

    van den Briel, T.; West, C. E.; Hautvast, J. G.; Vulsma, T.; de Vijlder, J. J.; Ategbo, E. A.

    2001-01-01

    Iodine deficiency control programs have greatly reduced iodine deficiency disorders worldwide. For monitoring changes in iodine status, different indicators may be used. The aim of this study was to evaluate the suitability of indicators of iodine status and thyroid function, thyroglobulin (Tg),

  12. Retrospective reconstruction of Iodine-131 distribution through the analysis of Iodine-129

    Science.gov (United States)

    Matsuzaki, Hiroyuki; Muramatsu, Yasuyuki; Ohno, Takeshi; Mao, Wei

    2017-09-01

    Iodine-131 distribution released from the Fukushima Dai-ichi Nuclear Power Plant accident was reconstructed through the iodine-129 measurements. From nearly 1,000 surface soil samples iodine was extracted by the pyro hydrolysis method. Extracted iodine was then mixed with carrier, purified and finally collected as silver iodide. Silver iodide sample was pressed into the cathode holder and set at the ion source of the MALT facility, The University of Tokyo. The isotopic ratio 129I/127I was measured by means of Accelerator Mass Spectrometry. From 129I data obtained, 131I deposition map was constructed. There observed various fine structures in the map which could not estimated neither by the simulation nor 137Cs distribution.

  13. Thyroid disorders in mild iodine deficiency

    DEFF Research Database (Denmark)

    Laurberg, P; Nøhr, S B; Pedersen, K M

    2000-01-01

    Comparative epidemiologic studies in areas with low and high iodine intake and controlled studies of iodine supplementation have demonstrated that the major consequence of mild-to-moderate iodine deficiency for the health of the population is an extraordinarily high occurrence of hyperthyroidism...... endangered but the consequences of severe iodine deficiency for brain development are grave and a considerable safety margin is advisable. Moreover, a shift toward less malignant types of thyroid cancer and a lower radiation dose to the thyroid in case of nuclear fallout support that mild-to-moderate iodine...... deficiency should be corrected. However, there is evidence that a high iodine intake may be associated with more autoimmune hypothyroidism, and that Graves' disease may manifest at a younger age and be more difficult to treat. Hence, the iodine intake should be brought to a level at which iodine deficiency...

  14. Biofortification of lettuce (Lactuca sativa L.) with iodine: the effect of iodine form and concentration in the nutrient solution on growth, development and iodine uptake of lettuce grown in water culture.

    Science.gov (United States)

    Voogt, Wim; Holwerda, Harmen T; Khodabaks, Rashied

    2010-04-15

    Iodine is an essential trace element for humans. Two billion individuals have insufficient iodine intake. Biofortification of vegetables with iodine offers an excellent opportunity to increase iodine intake by humans. The main aim was to study the effect of iodine form and concentration in the nutrient solution on growth, development and iodine uptake of lettuce, grown in water culture. In both a winter and summer trial, dose rates of 0, 13, 39, 65, and 90 or 129 microg iodine L(-1), applied as iodate (IO(3)(-)) or iodide (I(-)), did not affect plant biomass, produce quality or water uptake. Increases in iodine concentration significantly enhanced iodine content in the plant. Iodine contents in plant tissue were up to five times higher with I(-) than with IO(3)(-). Iodine was mainly distributed to the outer leaves. The highest iodide dose rates in both trials resulted in 653 and 764 microg iodine kg(-1) total leaf fresh weight. Biofortification of lettuce with iodine is easily applicable in a hydroponic growing system, both with I(-) and IO(3)(-). I(-) was more effective than IO(3)(-). Fifty grams of iodine-biofortified lettuce would provide, respectively, 22% and 25% of the recommended daily allowance of iodine for adolescents and adults. (c) 2010 Society of Chemical Industry.

  15. Assessing iodine intake, iodine status, and the effects of maternal iodine supplementation: introduction to articles arising from 3 workshops held by the NIH Office of Dietary Supplements12

    Science.gov (United States)

    Ershow, Abby G; Coates, Paul M; Swanson, Christine A

    2016-01-01

    The NIH Office of Dietary Supplements (ODS) convened 3 workshops on iodine nutrition in 2014, each held in Rockville, Maryland. These workshops were part of the ongoing ODS Iodine Initiative, begun in 2011 in response to concerns that US pregnant women may be at risk of iodine deficiency and that a high fraction of prenatal dietary supplements do not contain the recommended amounts of iodine. The primary purpose of the workshops was to consider the data and resources necessary to evaluate the clinical and public health benefits and risks of maternal iodine supplementation in the United States. The first workshop focused on the assessment of iodine intake, the second focused on the assessment of iodine status, and the third focused on the design and interpretation of clinical trials of maternal iodine supplementation. Here we provide the background of the ODS Iodine Initiative, summarize the 3 workshops held in 2014, and introduce the articles that arose from the workshops and are published in this supplement issue. PMID:27534646

  16. Enhancement of mechanical properties of epoxy/graphene nanocomposite

    Science.gov (United States)

    Berhanuddin, N. I. C.; Zaman, I.; Rozlan, S. A. M.; Karim, M. A. A.; Manshoor, B.; Khalid, A.; Chan, S. W.; Meng, Q.

    2017-10-01

    Graphene is a novel class of nanofillers possessing outstanding characteristics including most compatible with most polymers, high absolute strength, high aspect ratio and cost effectiveness. In this study, graphene was used to reinforce epoxy as a matrix, to enhance its mechanical properties. Two types of epoxy composite were developed which are epoxy/graphene nanocomposite and epoxy/modified graphene nanocomposite. The fabrication of graphene was going through thermal expansion and sonication process. Chemical modification was only done for modified graphene where 4,4’-Methylene diphenyl diisocyanate (MDI) is used. The mechanical properties of both nanocomposite, such as Young’s modulus and maximum stress were investigated. Three weight percentage were used for this study which are 0.5 wt%, 1.0 wt% and 1.5 wt%. At 0.5 wt%, modified and unmodified shows the highest value compared to neat epoxy, where the value were 8 GPa, 6 GPa and 0.675 GPa, respectively. For maximum stress, neat epoxy showed the best result compared to both nanocomposite due to the changes of material properties when adding the filler into the matrix. Therefore, both nanocomposite increase the mechanical properties of the epoxy, however modification surface of graphene gives better improvement.

  17. Dietary Iodine Intake of the Australian Population after Introduction of a Mandatory Iodine Fortification Programme

    Directory of Open Access Journals (Sweden)

    Karen Charlton

    2016-11-01

    Full Text Available To address mild iodine deficiency in Australia, a mandatory fortification program of iodised salt in bread was implemented in 2009. This study aimed to determine factors associated with achieving an adequate dietary iodine intake in the Australian population post-fortification, and to assess whether bread consumption patterns affect iodine intake in high-risk groups. Using nationally representative data of repeated 24-h dietary recalls from the 2011–2012 Australian National Nutrition and Physical Activity Survey, dietary iodine intakes and food group contributions were compared by age, socioeconomic status (SES, and geographical remoteness (N = 7735. The association between fortified bread intake and adequacy of iodine intake (meeting age and sex-specific Estimated Average Requirements was investigated using logistic regression models in women of childbearing age 14–50 years (n = 3496 and children aged 2–18 years (n = 1772. The effect of SES on bread consumption was further investigated in a sub group of children aged 5–9 years (n = 488. Main sources of iodine intake at the time of the survey were cereal and cereal products, followed by milk products and dishes. Differences in iodine intake and dietary iodine habits according to age, SES and location were found (p < 0.001 for women of child-bearing age. Fortified bread consumption at ≥100 g/day was associated with five times greater odds of achieving an adequate iodine intake (OR 5.0, 95% CI 4.96–5.13; p < 0.001 compared to lower bread consumption in women and 12 times in children (OR 12.34, 95% CI 1.71–89.26; p < 0.001. Disparities in dietary iodine intake exist within sectors of the Australian population, even after mandatory fortification of a staple food. On-going monitoring and surveillance of iodine status is required.

  18. Iodine-deficiency disorders

    NARCIS (Netherlands)

    Zimmermann, M.B.; Jooste, P.L.; Pandav, C.S.

    2008-01-01

    billion individuals worldwide have insufficient iodine intake, with those in south Asia and sub-Saharan Africa particularly affected. Iodine deficiency has many adverse effects on growth and development. These effects are due to inadequate production of thyroid hormone and are termed

  19. Adhesion between coating layers based on epoxy and silicone

    DEFF Research Database (Denmark)

    Svendsen, Jacob R.; Kontogeorgis, Georgios; Kiil, Søren

    2007-01-01

    The adhesion between a silicon tie-coat and epoxy primers, used in marine coating systems, has been studied in this work. Six epoxy coatings (with varying chain lengths of the epoxy resins), some of which have shown problems with adhesion to the tie-coat during service life, have been considered....... The experimental investigation includes measurements of the surface tension of the tie-coat and the critical surface tensions of the epoxies, topographic investigation of the surfaces of cured epoxy coatings via atomic force microscopy (AFM), and pull-off tests for investigating the strength of adhesion...... to the silicon/epoxy systems. Calculations for determining the roughness factor of the six epoxy coatings (based on the AFM topographies) and the theoretical work of adhesion have been carried out. The coating surfaces are also characterized based on the van Oss-Good theory. Previous studies on the modulus...

  20. Radioactive iodine absorbing properties of tetrathiafulvalene

    Energy Technology Data Exchange (ETDEWEB)

    Ito, Tomiyasu; Nakamura, Asao (Ajinomoto Co. Inc., Kawasaki, Kanagawa (Japan). Central Research Labs.); Nogawa, Norio; Oohashi, Kunio; Morikawa, Naotake

    1989-05-01

    For the purpose of searching some effective absorbents of gaseous radioactive iodine, 16 substances considered as having an affinity for iodine were investigated with regular iodine and /sup 125/I. In a preliminary survey, only tetrathiafulvalene (TTF) was found to have satisfactory absorbing properties comparable to activated charcoal. A further detailed comparison of the properties between TTF and activated charcoal led us to the conclusion that the former has more preferable properties as absorbent of radioactive iodine than the latter in all points studied. The results are summarized as follows: (1) The absorption of iodine on TTF in atmosphere was about twice as much as that on activated charcoal. Desorption of iodine from saturatedly absorbed iodine on TTF was practically negligible except trace amount of initial desorption, while that on activated charcoal was considerable (3%/50h) even in the air at room temperature. (2) Absorbed amount of iodine on activated charcoal decreased with increasing gaseous iodine concentration, air flow rate, on humidity of flowing-air. On the other hand, those factors scarcely affected that on TTF. Under an air flow rate of 1m/s, activated charcoal absorbs only 80% of iodine, while TTF absorbs more than 99%. (3) In flowing-air saturated with water vapor, iodine absorbed on activated charcoal was gradually liberated although by small amount (0.08%/100h), while that on TTF was much more stable for a long period (0.004%/100h). As a conclusion, TTF is considered to be useful as a quite effective radioactive iodine absorbent, especially in the case where protection from radioactive iodine should be serious, though it is expensive now. (author).

  1. Radioactive iodine absorbing properties of tetrathiafulvalene

    International Nuclear Information System (INIS)

    Ito, Tomiyasu; Nakamura, Asao; Nogawa, Norio; Oohashi, Kunio; Morikawa, Naotake.

    1989-01-01

    For the purpose of searching some effective absorbents of gaseous radioactive iodine, 16 substances considered as having an affinity for iodine were investigated with regular iodine and 125 I. In a preliminary survey, only tetrathiafulvalene (TTF) was found to have satisfactory absorbing properties comparable to activated charcoal. A further detailed comparison of the properties between TTF and activated charcoal led us to the conclusion that the former has more preferable properties as absorbent of radioactive iodine than the latter in all points studied. The results are summarized as follows: (1) The absorption of iodine on TTF in atmosphere was about twice as much as that on activated charcoal. Desorption of iodine from saturatedly absorbed iodine on TTF was practically negligible except trace amount of initial desorption, while that on activated charcoal was considerable (3%/50h) even in the air at room temperature. (2) Absorbed amount of iodine on activated charcoal decreased with increasing gaseous iodine concentration, air flow rate, on humidity of flowing-air. On the other hand, those factors scarcely affected that on TTF. Under an air flow rate of 1m/s, activated charcoal absorbs only 80% of iodine, while TTF absorbs more than 99%. (3) In flowing-air saturated with water vapor, iodine absorbed on activated charcoal was gradually liberated although by small amount (0.08%/100h), while that on TTF was much more stable for a long period (0.004%/100h). As a conclusion, TTF is considered to be useful as a quite effective radioactive iodine absorbent, especially in the case where protection from radioactive iodine should be serious, though it is expensive now. (author)

  2. Dynamics of production of iodine atoms by dissociation of iodides in a pulsed self-sustained discharge

    International Nuclear Information System (INIS)

    Vagin, Nikolai P; Kochetov, Igor' V; Napartovich, A P; Yuryshev, Nikolai N

    2013-01-01

    Absorption at the laser transition has been used for the first time to assess the evolution of concentration of iodine atoms in a pulsed self-sustained discharge in mixtures of iodides with a buffer gas such as molecular nitrogen and helium. Dynamics of the iodine atom production is studied by the method of absorption spectroscopy. The dissociation of C n F 2n+1 I and CnH 2n+1 I (n = 1, 2) iodides is investigated. The energy required to produce atomic iodine is evaluated. The experimental data obtained for CF 3 I are compared with the results of numerical simulations, their reasonable agreement being demonstrated. (active media)

  3. Thyroid disorders in mild iodine deficiency.

    Science.gov (United States)

    Laurberg, P; Nøhr, S B; Pedersen, K M; Hreidarsson, A B; Andersen, S; Bülow Pedersen, I; Knudsen, N; Perrild, H; Jørgensen, T; Ovesen, L

    2000-11-01

    Comparative epidemiologic studies in areas with low and high iodine intake and controlled studies of iodine supplementation have demonstrated that the major consequence of mild-to-moderate iodine deficiency for the health of the population is an extraordinarily high occurrence of hyperthyroidism in elderly subjects, especially women, with risk of cardiac arrhythmias, osteoporosis, and muscle wasting. The hyperthyroidism is caused by autonomous nodular growth and function of the thyroid gland and it is accompanied by a high frequency of goiter. Pregnant women and small children are not immediately endangered but the consequences of severe iodine deficiency for brain development are grave and a considerable safety margin is advisable. Moreover, a shift toward less malignant types of thyroid cancer and a lower radiation dose to the thyroid in case of nuclear fallout support that mild-to-moderate iodine deficiency should be corrected. However, there is evidence that a high iodine intake may be associated with more autoimmune hypothyroidism, and that Graves' disease may manifest at a younger age and be more difficult to treat. Hence, the iodine intake should be brought to a level at which iodine deficiency disorders are avoided but not higher. Iodine supplementation programs should aim at relatively uniform iodine intake, avoiding deficient or excessive iodine intake in subpopulations. To adopt such a strategy, surveillance programs are needed.

  4. Iodine kinetics and effectiveness of stable iodine prophylaxis after intake of radioiodine: a review

    International Nuclear Information System (INIS)

    Geoffroy, B.; Verger, P.; Le Guen, B.

    2000-01-01

    Ingestion of stable iodine (potassium iodide) offers an efficient protection against the irradiation of the thyroid when an accidental exposure to radioiodine occurs. This prophylaxis aims at obtaining a rapid and maximum thyroid protection without antithyroid effects. This article reviews studies on iodine kinetics in the human and on stable iodine effectiveness to protect the thyroid. In adults with a normal thyroid function, ingestion of 100 mg of iodide just before exposure to radioiodine allows a percentage of thyroid averted dose equal or greater than 95%. If the exposure persists after iodide ingestion (100 mg), the percentage of averted dose may decrease significantly. Repeated ingestion of daily amounts of 15 mg of stable iodine would then allow to maintain a 90% effectiveness. Iodide effectiveness and antithyroid effects also depend on external and individual factors such as iodine amounts in the diet, thyroid function and age. It is recommended to adapt the amount of ingested stable iodine according to age at the time of exposure. (author)

  5. Chromosome painting in plants.

    NARCIS (Netherlands)

    Schubert, I.; Fransz, P.F.; Fuchs, J.; Jong, de J.H.

    2001-01-01

    The current 'state-of-art' as to chromosome painting in plants is reviewed. We define different situations described as painting so far: i) Genomic in situ hybridisation (GISH) with total genomic DNA to distinguish alien chromosomes on the basis of divergent dispersed repeats, ii) 'Chromosomal in

  6. Modification of (DGEBA epoxy resin with maleated depolymerised natural rubber

    Directory of Open Access Journals (Sweden)

    2008-04-01

    Full Text Available In this work, diglycidyl ether of bisphenol A (DEGBA type epoxy resin has been modified with maleated depolymerised natural rubber (MDPR. MDPR was prepared by grafting maleic anhydride onto depolymerised natural rubber. MDPR has been characterized by Fourier transform infrared (FT-IR spectroscopy and nuclear magnetic resonance spectroscopy. MDPR was blended with epoxy resin at three different ratios (97/3, 98/2 and 99/1, by keeping the epoxy resin component as the major phase and maleated depolymerised natural rubber component as the minor phase. The reaction between the two blend components took place between the acid/anhydride group in the MDPR and the epoxide group of the epoxy resin. The proposed reaction schemes were supported by the FT-IR spectrum of the uncured Epoxy/MDPR blends. The neat epoxy resin and Epoxy/MDPR blends were cured by methylene dianiline (DDM at 100°C for three hours. Thermal, morphological and mechanical properties of the neat epoxy and the blends were investigated. Free volume studies of the cured, neat epoxy and Epoxy/MDPR blends were correlated with the morphological and mechanical properties of the same systems using Positron Annihilation Lifetime Studies.

  7. Spectroscopic and structural investigation of interaction of 5-mercapto-3-phenyl-1,3,4-thiadiazole-2-thione potassium salt with molecular iodine

    Science.gov (United States)

    Ivolgina, Victoria A.; Chernov'yants, Margarita S.

    2018-06-01

    The interest in the study of heteroaromatic thioamides which are known to exhibit antithyroid activity is stimulated by the variety and an unusual structure their complexes with molecular iodine. The directions of dithiones investigation are diversity enough, however a few works are devoted to the study them as the potential thyreostatics. The ability of 5-mercapto-3-phenyl-1,3,4-thiadiazole-2-thion potassium salt to form the outer-sphere charge-transfer complex in dilute chloroform solution, coordinating 2 iodine molecules has been studied by UV-vis spectroscopy (lgβ = 7.91). The compound of the 5,5‧-disulfanediylbis(3-phenyl-1,3,4-thiadiazole-2(3H)-thione) - product of irreversible oxidation of 5-mercapto-3-phenyl-1,3,4-thiadiazole-2-thione potassium salt has been isolated and characterized by X-ray diffraction. Intermolecular interactions between sulfur atoms are observed with very short interatomic distance, shorter than sum of van der Waals radii. The contact between heterocyclic sulfur and heterocyclic nitrogen is also slightly short - 3.169 Å (0.053 Å less than vdW radii sum). This investigation constitutes a starting point for study of novel antithyroid drugs in future.

  8. Stress corrosion cracking of Zircaloy-4 in non-aqueous iodine solutions

    International Nuclear Information System (INIS)

    Gomez Sanchez, Andrea V.

    2006-01-01

    In the present work the susceptibility to intergranular attack and stress corrosion cracking of Zircaloy-4 in different iodine alcoholic solutions was studied. The influence of different variables such as the molecular weight of the alcohols, the water content of the solutions, the alcohol type (primary, secondary or tertiary) and the temperature was evaluated. To determine the susceptibility to stress corrosion cracking the slow strain rate technique was used. Specimens of Zircaloy-4 were also exposed between 0.5 and 300 hours to the solutions without applied stress to evaluate the susceptibility to intergranular attack. The electrochemical behavior of the material in the corrosive media was studied by potentiodynamic polarization tests. It was determined that the active species responsible for the stress corrosion cracking of Zircaloy-4 in iodine alcoholic solutions is a molecular complex between the alcohol and iodine. The intergranular attack precedes the 'true' stress corrosion cracking phenomenon (which is associated to the transgranular propagation of the crack) and it is controlled by the diffusion of the active specie to the tip of the crack. Water acts as inhibitor to intergranular attack. Except for methanolic solutions, the minimum water content necessary to inhibit stress corrosion cracking was determined. This critical water content decreases when increasing the molecular weight of the alcohol. An explanation for this behavior is proposed. The susceptibility to stress corrosion cracking also depends on the type of the alcohol used as solvent. The temperature dependence of the crack propagation rate is in agreement with a thermal activated process, and the activation energy is consistent with a process controlled by the volume diffusion of the active species. (author) [es

  9. Polymerization of epoxy resins studied by positron annihilation

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, T. [Radiation Science Center, High Energy Accelerator Research Organization (KEK), Tsukuba (Japan); Hayashi, T. [Fine Chemical Research Lab., Sumitomo Chemical, Tsukuba (Japan); Ito, Y. [Research Center for Nuclear Science and Technology, Univ. of Tokyo (Japan)

    2001-04-01

    Positron annihilation lifetime spectroscopy (PALS) has been applied to study polymerization of epoxy resins of cresole novolac with a hardener of phenol novolac. PALS uses positrons to probe the microstructure of a nanometer (nm) size. Using PALS polymerization can be followed through three states: powder (monomer), liquid and solid. PALS is a unique method for the detection of intermolecular spaces, hence polymerization was followed from the point of view of free spaces (inter-molecular spaces) between polymer networks. The glass transition temperature (T{sub g}) was determined from the temperature dependence of the positronium (Ps) lifetime. Although Tg determined by PALS is usually lower than that determined by a mechanical analysis (TMA), it was observed that T{sub g} approached the value determined by TMA after long curing. Ps can form bubbles in a liquid, and the surface tension of a mixture of the resin and the hardener was calculated from a simple empirical formula using the Ps lifetime; the resulting value is similar to that of the bisphenol-A epoxy resin. Gelation was observed as an increase in the intensity of Ps and a sharp decrease in the lifetime. (orig.)

  10. Prophylactic iodine treatment in radiation protection

    International Nuclear Information System (INIS)

    Oberhausen, E.

    1980-01-01

    Prophylactic iodine treatment is to prevent accumulation of radioactive iodine in the thyroid. This is done by administering a large amount of stable iodine before uptake of radioactive iodine so that further accummulation of iodine in the thyroid will be impossible. This blocking effect should be as complete as possible. This is achieved by administering an initial dose of 200 mg potassium iodide. As the release of radioactive iodine may last several hours or even days; for this reason, maintenance doses of 100 mg potassium iodide should be administered in 8-hour intervals. The risk of prophylactiv iodine treatment is rather low; however, provocation of latent hyperthyreoses must be expected in, at the most, 0.2% of the exposed population. (orig./MG) [de

  11. Iodine excretion in school children in Copenhagen

    DEFF Research Database (Denmark)

    Rasmussen, Lone B.; Kirkegaard-Klitbo, Ditte Marie; Laurberg, Peter

    2016-01-01

    INTRODUCTION: Studies of dietary habits show a high iodine intake in children in Denmark. Iodine excretion in children has not previously been assessed. Iodine excretion in adults is below the recommended threshold, and it is therefore being discussed to increase the fortification level. The main...... objective of this study was to assess iodine excretion in children living in Copenhagen to establish whether a moderate increase in iodine fortification would lead to excess iodine intake in this group. METHODS: Children in first and fifth grade were recruited through schools in Copenhagen. In total, 244...... children de-ivered a urine sample. Urine samples were analysed for iodine and creatinine, and the results were expressed as urinary iodine concentration (UIC) and as estimated 24-h iodine excretion. Iodine excretion in children was also compared with that of adults living in the same area, investigated...

  12. Iodine-infused aeration for hull fouling prevention: a vessel-scale study.

    Science.gov (United States)

    Dickenson, Natasha C; Krumholz, Jason S; Hunsucker, Kelli Z; Radicone, Michael

    2017-11-01

    Biofouling is a significant economic and ecological problem, causing reduced vessel performance and increases in fuel consumption and emissions. Previous research has shown iodine vapor (I 2 )-infused aeration to be an environmentally friendly method for deterring the settlement of fouling organisms. An aeration system was deployed on a vessel with hull sections coated with two types of antifoulant coatings, Intersleek ® 1100 (fouling-release) and Interspeed ® BRA-640 (ablative copper biocide), as well as an inert epoxy barrier coating, to assess the effectiveness of aeration in conjunction with common marine coatings. I 2 -infused aeration resulted in consistent reductions of 80-90% in hard fouling across all three coatings. Additionally, aeration reduced the soft fouling rate by 45-70% when used in conjunction with both Intersleek ® and Interspeed ® BRA versus those coatings alone. The results of this study highlight the contribution of I 2 -infused aeration as a standalone mechanism for fouling prevention or as a complement to traditional antifouling coatings.

  13. Silver iodide reduction in aqueous solution: application to iodine enhanced separation during spent nuclear fuels reprocessing

    International Nuclear Information System (INIS)

    Badie, Jerome

    2002-01-01

    Silver iodide is a key-compound in nuclear chemistry either in accidental conditions or during the reprocessing of spent nuclear fuel. In that case, the major part of iodine is released in molecular form into the gaseous phase at the time of dissolution in nitric acid. In French reprocessing plants, iodine is trapped in the dissolver off-gas treatment unit by two successive steps: the first consists in absorption by scrubbing with a caustic soda solution and in the second, residual iodine is removed from the gaseous stream before the stack by chemisorption on mineral porous traps made up of beds of amorphous silica or alumina porous balls impregnated with silver nitrate. Reactions of iodine species with the impregnant are assumed to lead to silver iodide and silver iodate. Enhanced separation policy would make necessary to recover iodine from the filters by silver iodide dissolution during a reducing treatment. After a brief silver-iodine chemical bibliographic review, the possible reagents listed in the literature were studied. The choice has been made to use ascorbic acid and hydroxylamine. An experimental work on silver iodide reduction by this two compounds allowed us to determinate reaction products, stoichiometry and kinetics parameters. Finally, the process has been initiated on stable iodine loaded filters samples. (author) [fr

  14. Action of ionizing radiation on epoxy resins

    Energy Technology Data Exchange (ETDEWEB)

    Van de Voorde, M. E.

    1970-12-01

    The resistance of classical and experimental epoxy resins to irradiation was studied. The resistance to irradiation of epoxy resins of diverse compositions as well as the development of resins having a radioresistance that approaches that of certain ceramics are discussed. Sources of irradiation and the techniques of dosimetry used are described. The structures of certain epoxy resins and of hardeners are given. The preparation of these resins and their physical properties is described. The effects of radiation on epoxy resins, as well as conditions of irradiation, and suggested mechanisms for degradation of the irradiated resins are discussed. The relationship between chemical structure of the resins and their physical properties is evaluated. (115 references) (JCB)

  15. Values of iodine metabolism biomarkers in assessing the iodine nutrition status in surgically treated patients with thyroid disease.

    Science.gov (United States)

    Han, Jian-hua; Wu, Lian; Yu, Song-lin; Fang, Hui-ling; Kamg, Wei-ming; Cheng, Xin-qi; Lu, Jie; Yu, Jian-chun; Qiu, Ling

    2015-04-01

    To assess the clinical application value of iodine metabolism biomarkers in assessing iodine nutrition status in surgically treated patients with thyroid disease. Blood,morning urine and 24-hour urine samples were collected in 31 healthy volunteers and in 30 surgically treated patients with thyroid disease before and after surgery. Iodine concentration was analyzed by inductively coupled plasma mass spectrometry. The iodine metabolism biomarkers including serum iodine (SI), morning urine iodine(UI), morning urine iodine/urine creatinine ratio (UI/UCr), 24-hour urine iodine (24 h UI), and 24-hour urine iodine excretion (24 h UIE) were evaluated in these two groups. In addition, the validation coincidence rate of iodine metabolism biomarkers in healthy volunteers to different reference ranges including World Health Organization, Mayo Clinic, and Quest Diagnostics were calculated. The UI/UCr ratio of pre-operative thyroid disease patients was significantly lower than that of healthy volunteers (P0.05) between these two groups. The SI, UI ,and 24 h UI in postoperative thyroid disease patients were significantly higher than those of the pre-operative patients (all Piodine metabolism biomarkers. The UI/UCr ratio may be used for iodine nutrition evaluation in surgically treated patients with thyroid disease.

  16. Longitudinal study of iodine in toenails following IV administration of an iodine-containing contrast agent

    International Nuclear Information System (INIS)

    Spate, V.L.; Morris, J.S.; Nichols, T.A.; Baskett, C.K.; Mason, M.M.; Horsman, T.L.; McDougall, I.R.

    1998-01-01

    The literature on the relationship between diet and thyroid cancer (TC) risk and the higher incidence of TC among Asian immigrants to the US compared to second and third generation subgroups has prompted epidemiologists to hypothesize that increased levels of iodine consumption may be associated with TC risk, particularly among persons with a history of clinical or subclinical thyroid dysfunction. At the University of Missouri Research Reactor (MURR), we have applied epiboron neutron activation analysis to investigate human nails as a dietary monitor for iodine. Preliminary studies have indicated a positive correlation between dietary iodine intake and the concentration of iodine in toenails. However, these studies are confounded by high iodine levels (up to 30 ppm) in approximately 5% of the nails studied. We hypothesize that, in the subjects we have studied, the high iodine levels may be due to iodine-containing medications, in particular contrast-agents containing iopamidol. This paper will report on longitudinal studies using contrast agent subjects who where followed-up for almost two years compared to a longitudinal control and a population mean. Based on this study, we suggest that iodine-containing contrast agents contaminate nail samples via non-specific binding in the short term followed by incorporation in the nail as a result of absorption. (author)

  17. Flexural Properties of Activated Carbon Filled Epoxy Nano composites

    International Nuclear Information System (INIS)

    Khalil, H.P.S.A.; Khalil, H.P.S.A.; Alothman, O.Y.; Paridah, M.T.; Zainudin, E.S.

    2014-01-01

    Activated carbon (AC) filled epoxy nano composites obtained by mixing the desired amount of nano AC viz., bamboo stem, oil palm empty fruit bunch, and coconut shell from agricultural biomass with the epoxy resin. Flexural properties of activated carbons filled epoxy nano composites with 1 %, and 5 % filler loading were measured. In terms of flexural strength and modulus, a significant increment was observed with addition of 1 % vol and 5 % vol nano-activated carbon as compared to neat epoxy. The effect of activated carbon treated by two chemical agents (potassium hydroxide and phosphoric acid) on the flexural properties of epoxy nano composites were also investigated. Flexural strength of activated carbon-bamboo stem, activated carbon-oil palm, and activated carbon-coconut shell reinforced epoxy nano composites showed almost same value in case of 5 % potassium hydroxide activated carbon. Flexural strength of potassium hydroxide activated carbon-based epoxy nano composites was higher than phosphoric acid activated carbon. The flexural toughness of both the potassium hydroxide and phosphoric acid activated carbon reinforced composites range between 0.79 - 0.92 J. It attributed that developed activated carbon filled epoxy nano composites can be used in different applications. (author)

  18. Study on adsorption performance of coal based activated carbon to radioactive iodine and stable iodine

    International Nuclear Information System (INIS)

    Zhou, Junbo; Hao, Shan; Gao, Liping; Zhang, Youchen

    2014-01-01

    Highlights: • The impregnated coal-based activated carbons as adsorbent for removing methyl iodide. • The coal-based activated carbons to remove stable iodine. • Iodine residues are under 0.5 μg/ml after adsorption treatment. • The decontamination factor is much higher than 1000. - Abstract: Nuclear power plant, nuclear reactors and nuclear powered ship exhaust contains a large amount of gaseous radioactive iodine, and can damage to the workplace and the surrounding environment. The quantitative test to remove methyl iodide and the qualitative test for removing stable iodine were investigated using the impregnated coal-based activated carbons and coal-based activated carbons as adsorbents. The research conducted in this work shows that iodine residues were under 0.5 μg/ml after adsorption treatment and the decontamination factor of the coal-based activated carbon for removing the stable iodine was more than 1000, which can achieve the purpose of removing harmful iodine, and satisfy the requirement of gaseous waste treatment of nuclear powered vessel and other nuclear plants

  19. Molecular dynamics of palmitic acid and lead palmitate in cross-linked linseed oil films: Implications from deuterium magnetic resonance for lead soap formation in traditional oil paintings.

    Science.gov (United States)

    Catalano, Jaclyn; Murphy, Anna; Yao, Yao; Zumbulyadis, Nicholas; Centeno, Silvia A; Dybowski, Cecil

    2018-02-01

    Many oil paintings, dating from the 15th century to the present, are affected by the formation of heavy-metal carboxylates (soaps) that alter the structural integrity and appearance of the works. Through transport phenomena not yet understood, free fatty acids formed from oils used as binders migrate through the paint film and react with heavy-metal ions that are constituents of pigments and/or driers, forming metal carboxylates. The local molecular dynamics of fatty acids and metal carboxylates are factors influencing material transport in these systems. We report temperature-dependent 2 H NMR spectra of palmitic acid and lead palmitate as pure materials, in cross-linked linseed oil films, and in a lead white linseed oil paint film as part of our broader research into metal soap formation. Local dynamics at the α carbon, at the terminal methyl group, and at the middle of the fatty acid chain were observed in specifically deuterated materials. Changes in the dynamic behavior with temperature were observed by the appearance of two species, a solid-like material and a liquid-like material. The relative amounts of the two phases and their deuterium NMR parameters indicate that the amount of liquid-like material and the local dynamics at that site increase with temperature. At the three locations along the chain and at all temperatures, there is a larger percentage of acyl chains of both palmitic acid and lead palmitate that are "mobile" or liquid-like in linseed oil films than there are in the pure materials. However, the percentage of liquid-like species is decreased in a lead white paint film, as compared to a linseed oil matrix. In addition, these experiments indicate that there is a larger percentage of liquid-like acyl chains of palmitic acid than of lead palmitate under identical conditions in these model paint systems. Copyright © 2017 Elsevier Inc. All rights reserved.

  20. The colors of paintings and viewers' preferences.

    Science.gov (United States)

    Nascimento, Sérgio M C; Linhares, João M M; Montagner, Cristina; João, Catarina A R; Amano, Kinjiro; Alfaro, Catarina; Bailão, Ana

    2017-01-01

    One hypothesis to explain the aesthetics of paintings is that it depends on the extent to which they mimic natural image statistics. In fact, paintings and natural scenes share several statistical image regularities but the colors of paintings seem generally more biased towards red than natural scenes. Is the particular option for colors in each painting, even if less naturalistic, critical for perceived beauty? Here we show that it is. In the experiments, 50 naïve observers, unfamiliar with the 10 paintings tested, could rotate the color gamut of the paintings and select the one producing the best subjective impression. The distributions of angles obtained are described by normal distributions with maxima deviating, on average, only 7 degrees from the original gamut orientation and full width at half maximum just above the threshold to perceive a chromatic change in the paintings. Crucially, for data pooled across observers and abstract paintings the maximum of the distribution was at zero degrees, i.e., the same as the original. This demonstrates that artists know what chromatic compositions match viewers' preferences and that the option for less naturalistic colors does not constrain the aesthetic value of paintings. Copyright © 2016 Elsevier Ltd. All rights reserved.

  1. The speciation of iodine in the environment

    International Nuclear Information System (INIS)

    Bulman, R.A.

    1986-01-01

    The speciation of iodine in the environment is discussed under the following topics: (i) sea surface to atmosphere, (ii) chemistry in bulk seawater, (iii) iodine in rocks, (iv) iodine in soils, (v) iodine in plants and (vi) iodine in solidified wastes. (author)

  2. Iodine deficiency in pregnancy in Denmark. Regional variations and frequency of individual iodine supplementation

    DEFF Research Database (Denmark)

    Nøhr, S B; Laurberg, Peter; Børlum, K G

    1993-01-01

    Iodine requirements are increased during pregnancy and lactation and adequate iodine intake is important for normal brain development of the fetus/newborn child. The aim of the present study was to evaluate the extent to which this increase in iodine requirement is met in pregnant women living...... micrograms/g creatinine). These values are far below internationally recommended levels. The consequences remain to be evaluated and no firm recommendations can be given. It seems reasonable, however, to recommend a high intake of food containing iodine (e.g. milk products) during pregnancy and lactation...

  3. Iodine deficiency in pregnancy in Denmark. Regional variations and frequency of individual iodine supplementation

    DEFF Research Database (Denmark)

    Nøhr, S B; Laurberg, P; Børlum, K G

    1993-01-01

    micrograms/g creatinine). These values are far below internationally recommended levels. The consequences remain to be evaluated and no firm recommendations can be given. It seems reasonable, however, to recommend a high intake of food containing iodine (e.g. milk products) during pregnancy and lactation...... containing vitamin/mineral tablets. Approximately one third of the women had received tablets containing iodine. In women who had not received iodine supplementation urinary iodine was low with a median value of 39.7 micrograms/g creatinine (Aalborg 28, Randers 33, Ringkøbing 34, Arhus 43 and Copenhagen 62...

  4. Atomistic Modeling of Thermal Conductivity of Epoxy Nanotube Composites

    Science.gov (United States)

    Fasanella, Nicholas A.; Sundararaghavan, Veera

    2016-05-01

    The Green-Kubo method was used to investigate the thermal conductivity as a function of temperature for epoxy/single wall carbon nanotube (SWNT) nanocomposites. An epoxy network of DGEBA-DDS was built using the `dendrimer' growth approach, and conductivity was computed by taking into account long-range Coulombic forces via a k-space approach. Thermal conductivity was calculated in the direction perpendicular to, and along the SWNT axis for functionalized and pristine SWNT/epoxy nanocomposites. Inefficient phonon transport at the ends of nanotubes is an important factor in the thermal conductivity of the nanocomposites, and for this reason discontinuous nanotubes were modeled in addition to long nanotubes. The thermal conductivity of the long, pristine SWNT/epoxy system is equivalent to that of an isolated SWNT along its axis, but there was a 27% reduction perpendicular to the nanotube axis. The functionalized, long SWNT/epoxy system had a very large increase in thermal conductivity along the nanotube axis (~700%), as well as the directions perpendicular to the nanotube (64%). The discontinuous nanotubes displayed an increased thermal conductivity along the SWNT axis compared to neat epoxy (103-115% for the pristine SWNT/epoxy, and 91-103% for functionalized SWNT/epoxy system). The functionalized system also showed a 42% improvement perpendicular to the nanotube, while the pristine SWNT/epoxy system had no improvement over epoxy. The thermal conductivity tensor is averaged over all possible orientations to see the effects of randomly orientated nanotubes, and allow for experimental comparison. Excellent agreement is seen for the discontinuous, pristine SWNT/epoxy nanocomposite. These simulations demonstrate there exists a threshold of the SWNT length where the best improvement for a composite system with randomly oriented nanotubes would transition from pristine SWNTs to functionalized SWNTs.

  5. Effect of iodine solutions on polyaniline films

    International Nuclear Information System (INIS)

    Ayad, M.M.; Amer, W.A.; Stejskal, J.

    2009-01-01

    Polyaniline (PANI) emeraldine-base films have been exposed to iodine solutions. The interaction between the films and the iodine solution was studied using the quartz-crystal microbalance (QCM) technique and the UV-visible absorption spectroscopy. The iodine-treated film of emeraldine base was subjected to dedoping process using 0.1 M ammonia solution. The resulting film was exposed again to the previously used iodine solution. Iodine was found to play multiple roles: the ring-iodination of PANI film, the oxidation of PANI to pernigraniline base, and iodine doping to PANI salt. A sensor based on PANI-coated electrode of QCM was developed to monitor the presence of iodine in solution.

  6. Halloysite reinforced epoxy composites with improved mechanical properties

    Directory of Open Access Journals (Sweden)

    Saif Muhammad Jawwad

    2016-03-01

    Full Text Available Halloysite nanotubes (HNTs reinforced epoxy composites with improved mechanical properties were prepared. The prepared HNTs reinforced epoxy composites demonstrated improved mechanical properties especially the fracture toughness and flexural strength. The flexural modulus of nanocomposite with 6% mHNTs loading was 11.8% higher than that of neat epoxy resin. In addition, the nanocomposites showed improved dimensional stability. The prepared halloysite reinforced epoxy composites were characterized by thermal gravimetric analysis (TGA. The improved properties are attributed to the unique characteristics of HNTs, uniform dispersion of reinforcement and interfacial coupling.

  7. Shape memory polymers from benzoxazine-modified epoxy

    International Nuclear Information System (INIS)

    Rimdusit, Sarawut; Lohwerathama, Montha; Dueramae, Isala; Hemvichian, Kasinee; Kasemsiri, Pornnapa

    2013-01-01

    Novel shape memory polymers (SMPs) were prepared from benzoxazine-modified epoxy resin. Specimens consisting of aromatic epoxy (E), aliphatic epoxy (N), Jeffamine D230 (D) and BA-a benzoxazine monomer (B) were evaluated. The mole ratio of D/B was used as a mixed curing agent for an epoxy system with a fixed E/N. The effects of BA-a content on the thermal, mechanical and shape memory properties of epoxy-based shape memory polymers (SMPs) were investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), flexural test and shape recovery test. The results revealed that the obtained SMPs exhibited a higher flexural strength and flexural modulus than those of the unmodified epoxy-based SMP at room temperature and at 20 ° C above glass transition temperature (T g ). The presence of 1 mol BA-a as a curing agent provided the specimen with the highest T g , i.e. about 72 ° C higher than that of epoxy-based SMP cured by Jeffamine D230. All SMP samples needed only a few minutes to fully recover to their original shape. The samples exhibited high shape fixity (98–99%) and shape recovery ratio (90–100%). In addition, the recovery stress values increased with increasing BA-a mole ratio from 20 to 38 kPa, when BA-a up to 1 mol ratio was added. All of the SMP samples exhibited only minimum change in their flexural strength at the end of a 100 recovery cycles test. (paper)

  8. Structuralist readings: Painting vs. picture

    OpenAIRE

    Marinkov-Pavlović Lidija

    2016-01-01

    The aim of the paper is to point to two fundamentally different strategies of painting practice, that is, to two subsystems of painting: picture and painting. This differentiation can be made within the framework of semiotic and semiological analyses which have developed in theory under the influence of structuralism. The first part of the paper offers a basic insight into the linguistic foundation of structuralistic concept, and then sets a thesis about the possibility of analogue reconceptu...

  9. Electrochemistry of iodine

    Energy Technology Data Exchange (ETDEWEB)

    Yaraliev, Ya.A. (AN Azerbajdzhanskoj SSR, Baku. Inst. Neorganicheskoj i Fizicheskoj Khimii)

    1982-06-01

    The review is devoted to investigations into oxidation-reduction processes in different systems including iodine. The data on adsorption of iodine on metals are discussed; the connection between the nature of iodine adsorption and the mechanism of its electrode reactions is considered. The metals studied can be placed in the following series taking into account the degree of I sorption on them: Cd approximately Tl < Sn approximately Pb < Ga < Bi < Hg < Co approximately Ni < Fe < Ag approximately Rh approximately Pd approximately Ir < Pt. The data are given of standard and equilibrium potentials in iodine systems. Electric oxidation and electric reduction of iodide ions is investigated using the methods of Faraday impedance and rectification, methods of voltamperometry and oscillopolarography, rotating disc electrode, chronopotentiometry. Anode and cathode processes of oxidation-reduction reactions in I/sup -//IO/sub 3//sup -/, I/sub 2//IO/sub 3//sup -/ and I/sub 2//I/sup +/ systems are analyzed.

  10. Spectroscopic (multi-energy) CT distinguishes iodine and barium contrast material in MICE.

    Science.gov (United States)

    Anderson, N G; Butler, A P; Scott, N J A; Cook, N J; Butzer, J S; Schleich, N; Firsching, M; Grasset, R; de Ruiter, N; Campbell, M; Butler, P H

    2010-09-01

    Spectral CT differs from dual-energy CT by using a conventional X-ray tube and a photon-counting detector. We wished to produce 3D spectroscopic images of mice that distinguished calcium, iodine and barium. We developed a desktop spectral CT, dubbed MARS, based around the Medipix2 photon-counting energy-discriminating detector. The single conventional X-ray tube operated at constant voltage (75 kVp) and constant current (150 microA). We anaesthetised with ketamine six black mice (C57BL/6). We introduced iodinated contrast material and barium sulphate into the vascular system, alimentary tract and respiratory tract as we euthanised them. The mice were preserved in resin and imaged at four detector energy levels from 12 keV to 42 keV to include the K-edges of iodine (33.0 keV) and barium (37.4 keV). Principal component analysis was applied to reconstructed images to identify components with independent energy response, then displayed in 2D and 3D. Iodinated and barium contrast material was spectrally distinct from soft tissue and bone in all six mice. Calcium, iodine and barium were displayed as separate channels on 3D colour images at contrast agents with K-edges only 4 keV apart. Multi-contrast imaging and molecular CT are potential future applications.

  11. Spectroscopic (multi-energy) CT distinguishes iodine and barium contrast material in MICE

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, N.G. [University of Otago, Department of Radiology, Christchurch (New Zealand); Butler, A.P. [University of Otago, Department of Radiology, Christchurch (New Zealand); University of Canterbury, Physics and Astronomy, Christchurch (New Zealand); Scott, N.J.A. [University of Otago, Department of Medicine, Christchurch (New Zealand); Cook, N.J. [Christchurch Hospital, Medical Physics and Bioengineering, Christchurch (New Zealand); Butzer, J.S. [Karlsruhe Institute of Technology, Physics Department, Karlsruhe (Germany); Schleich, N. [University of Canterbury, Physics and Astronomy, Christchurch (New Zealand); Christchurch Hospital, Medical Physics and Bioengineering, Christchurch (New Zealand); Firsching, M. [Friedrich Alexander University, Physics Department, Erlangen (Germany); Grasset, R.; Ruiter, N. de [University of Canterbury, Hitlab NZ, Christchurch (New Zealand); Campbell, M. [European Organisation for Nuclear Research, Physics Section, Geneva (Switzerland); Butler, P.H. [University of Canterbury, Physics and Astronomy, Christchurch (New Zealand)

    2010-09-15

    Spectral CT differs from dual-energy CT by using a conventional X-ray tube and a photon-counting detector. We wished to produce 3D spectroscopic images of mice that distinguished calcium, iodine and barium. We developed a desktop spectral CT, dubbed MARS, based around the Medipix2 photon-counting energy-discriminating detector. The single conventional X-ray tube operated at constant voltage (75 kVp) and constant current (150 {mu}A). We anaesthetised with ketamine six black mice (C57BL/6). We introduced iodinated contrast material and barium sulphate into the vascular system, alimentary tract and respiratory tract as we euthanised them. The mice were preserved in resin and imaged at four detector energy levels from 12 keV to 42 keV to include the K-edges of iodine (33.0 keV) and barium (37.4 keV). Principal component analysis was applied to reconstructed images to identify components with independent energy response, then displayed in 2D and 3D. Iodinated and barium contrast material was spectrally distinct from soft tissue and bone in all six mice. Calcium, iodine and barium were displayed as separate channels on 3D colour images at <55 {mu}m isotropic voxels. Spectral CT distinguishes contrast agents with K-edges only 4 keV apart. Multi-contrast imaging and molecular CT are potential future applications. (orig.)

  12. Chromatographic assessment of two hybrid monoliths prepared via epoxy-amine ring-opening polymerization and methacrylate-based free radical polymerization using methacrylate epoxy cyclosiloxane as functional monomer.

    Science.gov (United States)

    Wang, Hongwei; Ou, Junjie; Lin, Hui; Liu, Zhongshan; Huang, Guang; Dong, Jing; Zou, Hanfa

    2014-11-07

    Two kinds of hybrid monolithic columns were prepared by using methacrylate epoxy cyclosiloxane (epoxy-MA) as functional monomer, containing three epoxy moieties and one methacrylate group. One column was in situ fabricated by ring-opening polymerization of epoxy-MA and 1,10-diaminodecane (DAD) using a porogenic system consisting of isopropanol (IPA), H2O and ethanol at 65°C for 12h. The other was prepared by free radical polymerization of epoxy-MA and ethylene dimethacrylate (EDMA) using 1-propanol and 1,4-butanediol as the porogenic solvents at 60°C for 12h. Two hybrid monoliths were investigated on the morphology and chromatographic assessment. Although two kinds of monolithic columns were prepared with epoxy-MA, their morphologies looked rather different. It could be found that the epoxy-MA-DAD monolith possessed higher column efficiencies (25,000-34,000plates/m) for the separation of alkylbenzenes than the epoxy-MA-EDMA monolith (12,000-13,000plates/m) in reversed-phase nano-liquid chromatography (nano-LC). Depending on the remaining epoxy or methacrylate groups on the surface of two pristine monoliths, the epoxy-MA-EDMA monolith could be easily modified with 1-octadecylamine (ODA) via ring-opening reaction, while the epoxy-MA-DAD monolith could be modified with stearyl methacrylate (SMA) via free radical reaction. The chromatographic performance for the separation of alkylbenzenes on SMA-modified epoxy-MA-DAD monolith was remarkably improved (42,000-54,000 plates/m) when compared with that on pristine epoxy-MA-DAD monolith, while it was not obviously enhanced on ODA-modified epoxy-MA-EDMA monolith when compared with that on pristine epoxy-MA-EDMA monolith. The enhancement of the column efficiency of epoxy-MA-DAD monolith after modification might be ascribed to the decreased mass-transfer resistence. The two kinds of hybrid monoliths were also applied for separations of six phenols and seven basic compounds in nano-LC. Copyright © 2014 Elsevier B.V. All

  13. Study on iodine levels in thyroids of iodine-supplemented rats by epithermal neutron activation analysis

    International Nuclear Information System (INIS)

    Wang Xuefei; Zhang Fang; Xu Qing; Liu Nianqing; Chai Zhifang; Zhao Xueqin; Zuo Aijun

    2003-01-01

    The second generation female Wistar rats that have been treated with iodine-deficient food, after their delivery, are divided into three groups i.e. excessive-iodine (EI), adequate-iodine (AI) and iodine-deficient (ID) according to the KIO 3 concentration in the drinking water (3.0, 0.4, 0 mg/L). In addition, the normal rats with low iodine food and 0.4 mg/L KIO 3 water are used as the control group (C). The iodine content in thyroid and the serum thyroid hormone levels of the third generation rats are measured by means of epithermal neutron activation analysis (ENAA), and the method of enzyme-linked immunosorbent assay (ELISA), respectively. The results indicate that the total thyroxine (TT 4 ) and the free thyroxine (FT 4 ) of the EI, compared with those of the controls, are significantly decreased (p 3 ) evidently increased (p 4 , FT 4 and goiter

  14. Iodine excretion has decreased in Denmark between 2004 and 2010 - the importance of iodine content in milk

    DEFF Research Database (Denmark)

    Rasmussen, Lone Banke; Carlé, Allan; Jørgensen, Torben

    2014-01-01

    Fortification with the essential trace element iodine is widespread worldwide. In the present study, results on iodine excretion and intake of iodine-rich foods from a cross-sectional study carried out in 2004-5, 4 to 5 years after the implementation of mandatory iodine fortification, were compared...... with data in a study carried out in 2008-10. The 2008-10 study was a follow-up of a cross-sectional study carried out before iodine fortification was implemented. Participants in the cross-sectional studies were randomly selected. Both studies were carried out in the cities of Aalborg and Copenhagen...... in Denmark. The median urinary iodine concentration decreased in women from 97 μg/l (n 2862) to 78 μg/l (n 2041) (Piodine excretion. The prevalence of users of iodine containing dietary...

  15. Separation and retention of iodine

    International Nuclear Information System (INIS)

    Thomas, T.R.

    1976-01-01

    Caustic and mercuric nitrate scrubbers have been used for iodine recovery from process offgas, but they exhibit low decontamination factors for organic iodide removal and produce liquid wastes that are unsuitable for final storage. The Iodox process gives high decontamination factors for both organic iodides and elemental iodine. The liquid waste can be evaporated to a solid or concentrated and fixed in cement. Efficient separation and retention of gaseous iodine species can be obtained with silver-loaded adsorbents. The waste is a dry solid easily handled and stored. Adsorbents containing cheaper metals appear to have lower iodine-loading capacities and may be unsuitable for bulk iodine removal from process offgas because of the large amounts of solid waste that would be generated. A potential method for regenerationg and recycling silver-loaded adsorbents is being evaluated. In conjunction with the regeneration, lead-exchanged zeolite is used as a secondary adsorbent for the final fixation and storage of the iodine

  16. Lead content in household paints in India

    International Nuclear Information System (INIS)

    Kumar, Abhay; Gottesfeld, Perry

    2008-01-01

    Lead and its compounds are used in paints not only to impart colour but also to make it durable, corrosion resistant and to improve drying. Adverse health impacts of lead especially on children have led countries to restrict or ban its use in paints. While U.S. and other developed countries instituted measures to limit the use of lead in paints, some developing countries including India have failed to regulate their lead content. The present study was undertaken to determine the levels of lead in new latex (water-based) and enamel paints (oil-based) intended for residential use in India. A total of 69 paint samples (38 latex and 31 enamel samples) from six of the most popular brands were analysed for lead concentrations. While all latex paint samples contained low levels of lead, (i.e., well below 600 ppm as regulated by United States' Consumer Products Safety Commission) the enamel paint samples of all but one brand contained significant concentrations of lead, ranging up to 140,000 ppm. In fact 84% of the enamel paints tested exceeded 600 ppm whereas only 38 % of all samples (including latex and enamel types) exceeded this regulatory level

  17. The importance of iodine nutrition during pregnancy.

    Science.gov (United States)

    Glinoer, Daniel

    2007-12-01

    To examine the importance of iodine nutrition during pregnancy. Review of existing literature of iodine in pregnancy. Population surveys and metabolic studies. Pregnant women. The main changes in thyroid function associated with pregnancy are due to an increase in hormone requirements that begin in the first trimester of gestation. This increase can only be met by a proportional increase in hormone production, something that depends directly upon the availability of iodine. When dietary iodine is lacking, an adequate physiological adaptation is difficult to achieve and is progressively replaced by pathological alterations that occur in parallel with the degree and duration of iodine deprivation. Iodine prophylaxis should be given systematically to women during pregnancy. In most public health programmes dealing with the correction of iodine deficiency disorders, iodised salt has been used as the preferred means to deliver iodine to households. Iodised salt, however, is not the ideal means of delivering iodine in the specific instances of pregnancy, breast-feeding and complementary feeding because of the need to limit salt intake during these periods. In European countries, presently it is proposed that iodine is given to pregnant women and breast-feeding mothers by systematically administering multivitamin tablets containing iodine in order to reach the recommended dietary allowance of 250 microg iodine day-1.

  18. Biofortification of lettuce (Lactuca sativa L.) with iodine: The effect of iodine form and concentration in the nutrient solution on growth, development and iodine uptake of lettuce grown in water culture

    NARCIS (Netherlands)

    Voogt, W.; Holwerda, H.T.; Khodabaks, M.R.

    2010-01-01

    BACKGROUND: Iodine is an essential trace element for humans. Two billion individuals have insufficient iodine intake. Biofortification of vegetables with iodine offers an excellent opportunity to increase iodine intake by humans. The main aim was to study the effect of iodine form and concentration

  19. Microbial influences on the mobility and transformation of radioactive iodine in the environment

    International Nuclear Information System (INIS)

    Amachi, Seigo; Fujii, Takaaki; Shinoyama, Hirofumi; Muramatsu, Yasuyuki

    2005-01-01

    Long-lived radioactive iodine ( 129 I, half-life: 1.57x10 7 y) has been released into the environment from nuclear fuel reprocessing plants. 129 I may also be released from ground storage of nuclear waste. Given its long half-life, a better understanding of the behavior of iodine in the environment is necessary to ensure the safety of humans and the health of the environment. In this report, we summarize our recent results and new experimental data about microbial influences on the mobility and transformation of iodine. Microbial volatilization of organic iodine was observed in soil slurries and seawater samples, and various species of aerobic bacteria were considered to play a significant role through methylation of iodide (I - ) to form methyl iodide (CH 3 I). The volatilization of iodine was also found in iodide-rich natural gas brine water, where iodide concentration is approximately 2,000 times higher than that in seawater. In this case, however, a significant amount of molecular iodine (I 2 ) was produced together with organic iodine compounds. Iodide-oxidizing bacteria, which oxidize iodide to I 2 , were isolated from seawater and natural gas brine water. Phylogenetically, they were divided into two groups within the alpha-subclass of the Proteobacteria (Roseovarius sp. and unidentified bacteria), and they produced not only I 2 but also diiodomethane (CH 2 I 2 ) and chloroiodomethane (CH 2 CII). Iodide-accumulating bacteria, which accumulate iodide to concentrations 5,500-fold over that of the medium, were also isolated from marine sediment. They were closely related to Arenibacter troitsensis, and iodide uptake was medicated by an active transport system. Our results suggest that the fate of iodine can be affected by microorganisms, particularly by bacteria, through processes such as volatilization, oxidation, and accumulation. (author)

  20. Cleaning of Easel Paintings: An Overview

    International Nuclear Information System (INIS)

    Bordalo, R.; Morais, P.J.; Gouveia, H.; Young, C.

    2006-01-01

    The application of laser cleaning to paintings is relatively recent despite its use on stone-based materials for over 30 years. The cleaning of paintings is of high importance, because it is the least reversible invasive intervention, as well as the most usual of all conservation treatments. Paintings are multilayer system of heterogeneous nature, often very sensitive and inherent difficult to clean. Being a noncontact method, laser cleaning has advantages compared to alternative techniques. Over the last decade, there have been important research studies and advances. However, they are far from sufficient to study the effects on painting materials and to establish the best parameters for each material under investigation. This paper presents a historical overview of the application of laser technology to the cleaning of paintings giving special emphasis on the research of the last decade. An overview of the current research into the interaction between the radiation and the different painting materials (varnish, pigments, and medium) is also given. The pigment's mechanisms of discoloration and the presence of media as a variable factor in the discoloration of pigments are discussed.

  1. Characterization and Curing Kinetics of Epoxy/Silica Nano-Hybrids

    Science.gov (United States)

    Yang, Cheng-Fu; Wang, Li-Fen; Wu, Song-Mao; Su, Chean-Cheng

    2015-01-01

    The sol-gel technique was used to prepare epoxy/silica nano-hybrids. The thermal characteristics, curing kinetics and structure of epoxy/silica nano-hybrids were studied using differential scanning calorimetry (DSC), 29Si nuclear magnetic resonance (NMR) and transmission electron microscopy (TEM). To improve the compatibility between the organic and inorganic phases, a coupling agent was used to modify the diglycidyl ether of bisphenol A (DGEBA) epoxy. The sol-gel technique enables the silica to be successfully incorporated into the network of the hybrids, increasing the thermal stability and improving the mechanical properties of the prepared epoxy/silica nano-hybrids. An autocatalytic mechanism of the epoxy/SiO2 nanocomposites was observed. The low reaction rate of epoxy in the nanocomposites is caused by the steric hindrance in the network of hybrids that arises from the consuming of epoxide group in the network of hybrids by the silica. In the nanocomposites, the nano-scale silica particles had an average size of approximately 35 nm, and the particles were well dispersed in the epoxy matrix, according to the TEM images. PMID:28793616

  2. High-performance fiber/epoxy composite pressure vessels

    Science.gov (United States)

    Chiao, T. T.; Hamstad, M. A.; Jessop, E. S.; Toland, R. H.

    1978-01-01

    Activities described include: (1) determining the applicability of an ultrahigh-strength graphite fiber to composite pressure vessels; (2) defining the fatigue performance of thin-titanium-lined, high-strength graphite/epoxy pressure vessel; (3) selecting epoxy resin systems suitable for filament winding; (4) studying the fatigue life potential of Kevlar 49/epoxy pressure vessels; and (5) developing polymer liners for composite pressure vessels. Kevlar 49/epoxy and graphite fiber/epoxy pressure vessels, 10.2 cm in diameter, some with aluminum liners and some with alternation layers of rubber and polymer were fabricated. To determine liner performance, vessels were subjected to gas permeation tests, fatigue cycling, and burst tests, measuring composite performance, fatigue life, and leak rates. Both the metal and the rubber/polymer liner performed well. Proportionately larger pressure vessels (20.3 and 38 cm in diameter) were made and subjected to the same tests. In these larger vessels, line leakage problems with both liners developed the causes of the leaks were identified and some solutions to such liner problems are recommended.

  3. Photochemistry of DNA containing iodinated cytosine

    Energy Technology Data Exchange (ETDEWEB)

    Rahn, R O; Stafford, R S [Oak Ridge National Lab., TN (USA)

    1979-10-01

    Irradiation at 313 nm of compounds containing iodinated cytosine moieties results in the photolysis of iodine. Photolysis occurs with a quantum yield of 0.022-0.024 for 5-iododeoxycytidine and 5-iododeoxycytidine monophosphate, and 0.004-0.008 for iodinated DNA as well as for iodinated polycytidylate. Photodegradation of the cytosine moiety occurs when air is present during irradiation, presumably due to the reaction of oxygen with the cytosyl radical formed when iodine is lost. This oxygen promoted photodegradation destroys the cytosine chromophore and is complete in the monomers but occurs to only a limited extent in the polymers. In the absence of oxygen or in the presence of ethanol, photodegradation is prevented and the loss of iodine leads exclusively to the formation of the cytosine chromophore. In DNA, the loss of iodine is accompanied by the formation of sugar damage and/or chain breaks. As measured by sedimentation in alkaline sucrose gradients, approximately one break is made for every six iodines lost in denatured DNA. The frequency of chain breakage per iodine photolyzed is reduced 2-fold in renatured DNA. Analysis in neutral gradients suggests that half of the breaks observed in alkali are alkali-labile bonds. Both ethanol and cysteamine reduce the number of chain breaks in alkali by approximately 3-fold.

  4. Experimental reproduction of iodine deficiency in cattle.

    Science.gov (United States)

    McCoy, M A; Smyth, J A; Ellis, W A; Arthur, J R; Kennedy, D G

    1997-11-22

    The role of iodine deficiency in stillbirth/perinatal weak calf syndrome was investigated in pregnant heifers. Five heifers were fed an iodine deficient diet (mean [sd] iodine concentration 0.06 [0.01] mg/kg dry matter [DM]) and six received an iodine sufficient diet (mean [sd] iodine concentration 1.45 [0.27] mg/kg DM). The diets consisted of wheat and soyabean meal with added minerals and vitamins (with or without iodine) and were fed to the heifers over the final four to five months of pregnancy. The iodine deficient diet produced clinicopathological changes and pathological changes in the thyroid glands of both the heifers and their offspring. However, all the calves in the iodine deficient group were born clinically normal.

  5. Iodine removing method in organic solvent

    International Nuclear Information System (INIS)

    Suzuki, Takeo; Sakurai, Manabu

    1988-01-01

    Purpose: To effectively remove iodine in an organic solvent to thereby remove iodine in the solvent that can be re-used or put to purning treatment. Method: Organic solvent formed from wastes of nuclear facilities is mixed with basic lead acetate, or silica gel or activated carbon incorporated with such a compound to adsorb iodine in the organic solvent to the basic lead acetate. Then, iodine in the organic solvent is removed by separating to eliminate the basic lead acetate adsorbing iodine from the organic solvent or by passing the organic solvent through a tower or column charged or pre-coated with silica gel or activated carbon incorporated with lead acetate. By using basic lead acetate as the adsorbents, iodine can effective by adsorbed and eliminated. Thus, the possibility of circumstantial release of iodine can be reduced upon reusing or burning treatment of the organic solvent. (Kamimura, M.)

  6. Viscoelastic properties of graphene-based epoxy resins

    Science.gov (United States)

    Nobile, Maria Rossella; Fierro, Annalisa; Rosolia, Salvatore; Raimondo, Marialuigia; Lafdi, Khalid; Guadagno, Liberata

    2015-12-01

    In this paper the viscoelastic properties of an epoxy resin filled with graphene-based nanoparticles have been investigated in the liquid state, before curing, by means of a rotational rheometer equipped with a parallel plate geometry. Exfoliated graphite was prepared using traditional acid intercalation followed by a sudden treatment at high temperature (900°C). The percentage of exfoliated graphite was found to be 56%. The epoxy matrix was prepared by mixing a tetrafunctional precursor with a reactive diluent which produces a significant decrease in the viscosity of the epoxy precursor so that the dispersion step of nanofillers in the matrix can easily occur. The hardener agent, the 4,4-diaminodiphenyl sulfone (DDS), was added at a stoichiometric concentration with respect to all the epoxy rings. The inclusion of the partially exfoliated graphite (pEG) in the formulated epoxy mixture significantly modifies the rheological behaviour of the mixture itself. The epoxy mixture, indeed, shows a Newtonian behaviour while, at 3 wt % pEG content, the complex viscosity of the nanocomposite clearly shows a shear thinning behaviour with η* values much higher at the lower frequencies. The increase in complex viscosity with the increasing of the partially exfoliated graphite content was mostly caused by a dramatic increase in the storage modulus. All the graphene-based epoxy mixtures were cured by a two-stage curing cycles: a first isothermal stage was carried out at the lower temperature of 125°C for 1 hour while the second isothermal stage was performed at the higher temperature of 200°C for 3 hours. The mechanical properties of the cured nanocomposites show high values in the storage modulus and glass transition temperature.

  7. 127I Moessbauer study of some oxygen bonded iodine(I) and iodine(III) complexes

    International Nuclear Information System (INIS)

    Bardhan, M.; Birchall, T.; Frampton, C.; Kapoor, P.

    1988-01-01

    127 I Moessbauer spectra have been recorded at 4.2 0 K for a series of oxygen bonded iodine(I) and iodine(III) complexes. The sign of the quadrupole coupling constant is dependant only on the primary arrangement of ligands about the central iodine nucleus whereas the magnitude and the asymmetry parameter are more sensitive to ligand electronegativity and type. (orig.)

  8. Epoxy Nanocomposites Containing Zeolitic Imidazolate Framework-8.

    Science.gov (United States)

    Liu, Cong; Mullins, Michael; Hawkins, Spencer; Kotaki, Masaya; Sue, Hung-Jue

    2018-01-10

    Zeolitic imidazole framework-8 (ZIF-8) is utilized as a functional filler and a curing agent in the preparation of epoxy nanocomposites. The imidazole group on the surface of the ZIF-8 initiates epoxy curing, resulting in covalent bonding between the ZIF-8 crystals and epoxy matrix. A substantial reduction in dielectric constant and increase in tensile modulus were observed. The implication of the present study for utilization of metal-organic framework to improve physical and mechanical properties of polymeric matrixes is discussed.

  9. Chemical generation of iodine atoms

    Energy Technology Data Exchange (ETDEWEB)

    Hewett, Kevin B. [Directed Energy Directorate, Air Force Research Laboratory, 3550 Aberdeen Avenue SE, Kirtland AFB, NM 87117-5776 (United States)]. E-mail: kevin.hewett@kirtland.af.mil; Hager, Gordon D. [Directed Energy Directorate, Air Force Research Laboratory, 3550 Aberdeen Avenue SE, Kirtland AFB, NM 87117-5776 (United States); Crowell, Peter G. [Northrup Grumman Information Technology, Science and Technology Operating Unit, Advanced Technology Division, P.O. Box 9377, Albuquerque, NM 87119-9377 (United States)

    2005-01-10

    The chemical generation of atomic iodine using a chemical combustor to generate the atomic fluorine intermediate, from the reaction of F{sub 2} + H{sub 2}, followed by the production of atomic iodine, from the reaction of F + HI, was investigated. The maximum conversion efficiency of HI into atomic iodine was observed to be approximately 75%, which is in good agreement with the theoretical model. The conversion efficiency is limited by the formation of iodine monofluoride at the walls of the combustor where the gas phase temperature is insufficient to dissociate the IF.

  10. Preparation of water paint by radiation

    International Nuclear Information System (INIS)

    Makuuchi, Keizo

    1984-01-01

    The development of coatings which do not require any organic solvent have been the social needs. The emulsion made by radiation method is considered to meet possibly this requirement, but it has not been utilized well in the application to water paint. In this review, the investigation concerning the synthesis of water paint raw material by radiation is summarized. In the introduction, radiation curing, water paint and radiation emulsion polymerization are outlined, in the section of γ-ray emulsion polymerization, clean emulsion, cross-linked polymer particles and low temperature polymerization are described, and in the section of paint characteristics of radiation-induced emulsion-polymerized emulsion, the synthesis of thermosetting emulsion, the relation between the method of polymerization and the properties of emulsion, the performance of coating film, and self-hardening emulsion are explained. In the following section of skin-core double layer structured particle emulsion, skin-core double layer structured particles, optimal monomer composition, optimal polymerization process, the manufacturing test with a pilot plant, the performance of the paint, the durability of skin-core double layer structured particle coating film and low temperature curing water paint are described, and in the section of synthesis of emulsion by utilization of electron beam, electron beam emulsion polymerization and the synthesis of water paint by electron beam graft polymerization are described. (Yoshitake, I.)

  11. Denotative and connotative meanings of paintings

    Directory of Open Access Journals (Sweden)

    Vasić Sandra

    2007-01-01

    Full Text Available In this study the relationships between judgments of paintings denotative and connotative meanings was investigated. Denotative domain was defined as motif (represented object, e.g. portrait, landscape etc. and message (information carried by paintings, e.g. celebration of patriotism. Connotative domain was defined as subjective experience, i.e. affective or metaphoric impression produced by painting (e.g. feeling of pleasure, impression of dynamics, and so on. In preliminary study the list of 39 motifs was specified empirically. The four dimensions of pictorial message were taken from the previous study (Marković, 2006: Subjectivism, Ideology, Decoration and Constructivism vs. Realism. The four dimensions of paintings subjective experience were taken from the previous study as well (Radonjić and Marković, 2005: Regularity, Attraction, Arousal and Relaxation. In Experiment 1 subjects were asked to associate 39 motifs with 18 paintings. In Experiment 2 subjects were asked to judge 24 paintings on four dimensions of pictorial message. Results form Experiment 1 have shown that dimensions of paintings subjective experience were significantly correlated with only five motifs (e.g. everyday life was negatively correlated with Arousal, battle was negatively correlated with Relaxation, and so on. Results from Experiment 2 have shown that Subjectivism and Constructivism are negatively correlated with Regularity, and positively correlated with Arousal. Decoration is negatively correlated with Arousal and positively with Attraction and Relaxation.

  12. Removal of volatile iodine from gas bubbles rising in water pools: review and assessment of pool scrubbing codes

    International Nuclear Information System (INIS)

    Polo, J.; Herranz, L.E.; Peyres, V.; Escudero, M.

    1996-01-01

    During a hypothetical nuclear reactor accident with core damage the fission products released from the degrading fuel bundles often pass through aqueous beds before entering the containment, mitigating in part the source term. Several computer codes have been developed for predicting the fission product and aerosols removal in pool scrubbing scenarios. In addition to particle removal, these codes simulate the retention of some volatile iodine compounds. Nonetheless, experimental data on the matter are rather scarce and further validation remains to be done. In this work a review of volatile iodine removal models included in SPARC and BUSCA codes is presented. Besides, the results and discussions of a validation of both codes against the available experimental data are summarized. SPARC and BUSCA codes model the diffusion of iodine toward the bubble interface by using the film penetration theory, which assumes a double layer gas-liquid at the interface. However, there are some differences between the two models, mainly related to the boundary conditions in the aqueous volume for the diffusion of molecular iodine. In SPARC, a set of fast reactions in the liquid phase control both the molecular iodine concentration in the pool and the partition coefficient of iodine at the interface. Thus, the aqueous chemistry plays an important role in the boundary conditions for the diffusion process. On the contrary, the BUSCA model has no chemical considerations at all, and assumes a null iodine concentration in the water bulk. Several sensitivity studies have been made in order to weight the effect of these differences. The variables examined in these studies were the pool temperature and the incoming iodine concentration in the pool. Additionally, sensitivity studies focused on the steam mass fraction of the injected gas were performed to study the effect of the different approach of both models for the condensation process. The results showed a different sensitivity of SPARC

  13. Clinical and Biochemical Uses of Stable Iodine Measurements

    Energy Technology Data Exchange (ETDEWEB)

    Koutras, D. A. [Thyroid Section, Alexandra Hospital, Athens (Greece)

    1970-07-01

    Iodine and thyroid function are closely linked, since the only known role of iodine is its participation in the synthesis of thyroid hormones. Iodine metabolism may be represented as a metabolic cycle consisting of three main pools: the Plasma Inorganic Iodine (PIl) pool into which dietary iodine goes and from where it is either taken up by the thyroid or excreted by the kidneys, the intrathyroidal iodine pool, where. thyroid hormone synthesis occurs, and finally the peripheral pool of thyroid hormones, of which about 80% are deiodinated and 20% excreted with the faeces. Endemic goitre is usually due to iodine deficiency. There is no renal homeostatic mechanism to keep the PII level constant, and so adaptation to iodine deficiency occurs by increasing the thyroidal iodide clearance rate. Stable iodine measurements are necessary for a complete study of iodine metabolism. Estimates of the serum Protein-Bound Iodine (PBl) are the best index of thyroid function, estimates of the PII and of the urinary iodine are the best indices of iodine nutrition. (author)

  14. Iodine nutrition status in lactating mothers residing in countries with mandatory and voluntary iodine fortification programs: an updated systematic review.

    Science.gov (United States)

    Nazeri, Pantea; Mirmiran, Parvin; Shiva, Niloofar; Mehrabi, Yadollah; Mojarrad, Mehdi; Azizi, Fereidoun

    2015-06-01

    The aim of this review is to assess data available on iodine nutrition status in lactating mothers residing in countries with mandatory and voluntary iodine fortification programs and/or iodine supplementation. A systematic review was conducted by searching articles published between 1964 and 2013 in Pub Med, ISI Web, and Cochrane Library using iodine nutrition, lactation, iodine supplementation, and iodine fortification as keywords for titles and/or abstracts. Relevant articles were included if they reported urinary iodine concentration (UIC) in lactating mothers and, if determined, the type of iodine fortification program and/or iodine supplementation. Forty-two studies met the inclusion criteria. Among these, 21 studies assessed lactating mothers in countries with a mandatory iodine fortification program, 17 studies were from countries with voluntary and/or without iodine fortification programs, and four studies assessed iodine nutrition status in lactating mothers undergoing iodine supplementation. Among countries with mandatory iodine fortification programs, the range of salt iodization level in lactating mothers with a UIC 100 μg/L, it was between 15 and 60 ppm. Levels of UIC Chile, Iran, Mongolia, New Guinea, and Nigeria, the median or mean of UIC was >100 μg/L. There was a median or mean UIC program was voluntary, including Switzerland, Australia, New Zealand, Ireland, and Germany. However, in some countries with voluntary iodine fortification programs, such as the United States, Spain, and Japan, a mean or median UIC of >100 μg/L has been reported. Although universal salt iodization is still the most feasible and cost-effective approach for iodine deficiency control in pregnant and lactating mothers, UIC in lactating mothers of most countries with voluntary programs and in areas with mandatory iodine fortification is still within the iodine deficiency range, indicating that iodine supplementation in daily prenatal vitamin/mineral supplements in

  15. Plasma Treated Multi-Walled Carbon Nanotubes (MWCNTs for Epoxy Nanocomposites

    Directory of Open Access Journals (Sweden)

    Jie Lian

    2011-12-01

    Full Text Available Plasma nanocoating of allylamine were deposited on the surfaces of multi-walled carbon nanotubes (MWCNTs to provide desirable functionalities and thus to tailor the surface characteristics of MWCNTs for improved dispersion and interfacial adhesion in epoxy matrices. Plasma nanocoated MWCNTs were characterized using scanning electron microscopy (SEM, high-resolution transmission electron microscopy (HR-TEM, surface contact angle, and pH change measurements. Mechanical testing results showed that epoxy reinforced with 1.0 wt % plasma coated MWCNTs increased the tensile strength by 54% as compared with the pure epoxy control, while epoxy reinforced with untreated MWCNTs have lower tensile strength than the pure epoxy control. Optical and electron microscopic images show enhanced dispersion of plasma coated MWCNTs in epoxy compared to untreated MWCNTs. Plasma nanocoatings from allylamine on MWCNTs could significantly enhance their dispersion and interfacial adhesion in epoxy matrices. Simulation results based on the shear-lag model derived from micromechanics also confirmed that plasma nanocoating on MWCNTs significantly improved the epoxy/fillers interface bonding and as a result the increased composite strength.

  16. Development of AlN/Epoxy Composites with Enhanced Thermal Conductivity

    Science.gov (United States)

    Xu, Yonggang; Yang, Chi; Li, Jun; Zhang, Hailong; Hu, Song; Wang, Shiwei

    2017-01-01

    AlN/epoxy composites with high thermal conductivity were successfully prepared by infiltrating epoxy into AlN porous ceramics which were fabricated by gelcasting of foaming method. The microstructure, mechanical, and thermal properties of the resulting composites were investigated. The compressive strengths of the AlN/epoxy composites were enhanced compared with the pure epoxy. The AlN/epoxy composites demonstrate much higher thermal conductivity, up to 19.0 W/(m·K), compared with those by the traditional particles filling method, because of continuous thermal channels formed by the walls and struts of AlN porous ceramics. This study demonstrates a potential route to manufacture epoxy-based composites with extremely high thermal conductivity. PMID:29258277

  17. Development of AlN/Epoxy Composites with Enhanced Thermal Conductivity.

    Science.gov (United States)

    Xu, Yonggang; Yang, Chi; Li, Jun; Mao, Xiaojian; Zhang, Hailong; Hu, Song; Wang, Shiwei

    2017-12-18

    AlN/epoxy composites with high thermal conductivity were successfully prepared by infiltrating epoxy into AlN porous ceramics which were fabricated by gelcasting of foaming method. The microstructure, mechanical, and thermal properties of the resulting composites were investigated. The compressive strengths of the AlN/epoxy composites were enhanced compared with the pure epoxy. The AlN/epoxy composites demonstrate much higher thermal conductivity, up to 19.0 W/(m·K), compared with those by the traditional particles filling method, because of continuous thermal channels formed by the walls and struts of AlN porous ceramics. This study demonstrates a potential route to manufacture epoxy-based composites with extremely high thermal conductivity.

  18. Investigating the effect of artists’ paint formulation on degradation rates of TiO2‑based oil paints

    NARCIS (Netherlands)

    van Driel, B.A.; van den Berg, K. J.; Smout, M.; Dekker, N; Kooyman, P.J.; Dik, J.

    2018-01-01

    This study reports on the effect of artists’ paint formulation on degradation rates of TiO2-based oil paints. Titanium white oil paint exists in a multitude of different recipes, and the effect of the formulation on photocatalytic binder
    degradation kinetics is unknown. These formulations

  19. The high-power iodine laser

    Science.gov (United States)

    Brederlow, G.; Fill, E.; Witte, K. J.

    The book provides a description of the present state of the art concerning the iodine laser, giving particular attention to the design and operation of pulsed high-power iodine lasers. The basic features of the laser are examined, taking into account aspects of spontaneous emission lifetime, hyperfine structure, line broadening and line shifts, stimulated emission cross sections, the influence of magnetic fields, sublevel relaxation, the photodissociation of alkyl iodides, flashlamp technology, excitation in a direct discharge, chemical excitation, and questions regarding the chemical kinetics of the photodissociation iodine laser. The principles of high-power operation are considered along with aspects of beam quality and losses, the design and layout of an iodine laser system, the scalability and prospects of the iodine laser, and the design of the single-beam Asterix III laser.

  20. Prediction of Outside Surface Aluminium Tank Corrosion on TRIGA Mark - IIResearch Reactor Bandung

    International Nuclear Information System (INIS)

    Soedardjo

    2000-01-01

    The prediction of outside surface aluminium tank corrosion on researchreactor design which coated by epoxy paint, has been assessed. The new TRIGAMark - II Bandung research reactor tank design separated by 3 section arebottom, middle and upper section then inserted into the existing old reactor.The separation carried out caused by the space constraint on top of old tank,so that the novel tank impossible inserted into old tank all at once. Thespace between novel and old tank is 10 mm. After bottom and middle section oftank welded then followed by epoxy painting and inserted partially into oldtank. From then on the middle and upper section welded and followed by epoxypainting then inserted into old tank. Based on prediction result, that theroot cause of corrosion would be took place on welding and on imperfectlyepoxy painting area. The outside surface novel tank would be generated by thereaction between imperfectly epoxy painting area and the highly basecondition on cement grout that available on novel and old tank gap. (author)

  1. Geochemical Cycling of Iodine Species in Soils

    International Nuclear Information System (INIS)

    Hu, Q.; Moran, J.E.; Blackwood, V.

    2007-01-01

    Iodine is an important element in studies of environmental protection and human health, global-scale hydrologic processes and nuclear nonproliferation. Biogeochemical cycling of iodine in soils is complex, because iodine occurs in multiple oxidation states and as inorganic and organic species that may be hydrophilic, atmophilic, and biophilic. In this study, we applied new analytical techniques to study the content and speciation of stable iodine in representative surface soils, and sorption and transport behavior of iodine species (iodide, iodate, and 4-iodoaniline) in sediments collected at numerous nuclear facilities in the United States, where anthropogenic 129 I from prior nuclear fuel processing activities poses an environmental risk. The surface soil samples were chosen for their geographic locations (e.g., near the ocean or nuclear facilities) and for their differing physico-chemical characteristics (organic matter, texture, etc). Extracted solutions were analyzed by IC and ICP-MS methods to determine iodine concentrations and to examine iodine speciation (iodide, iodate, and organic iodine). In natural soils, iodine is mostly (nearly 90% of total iodine) present as organic species, while inorganic iodine becomes important (up to 50%) only in sediments with low organic matter. Results from laboratory column studies, aimed at examining transport of different iodine species, showed much greater retardation of 4-iodoaniline than iodide or iodate. Careful attention must be given to potential interconversion among species when interpreting the biogeochemical behavior of iodine in the environment. In addition to speciation, input concentration and residence time effects will influence the biogeochemical cycling of anthropogenic 129I deposited on surface soils

  2. Mock iodine-125 radiation source

    International Nuclear Information System (INIS)

    Coffey, D.L.

    1976-01-01

    An intimate mixture of americium-241 and iodine-129 provides an energy spectrum that reliably simulates the spectrum of iodine-125 in a well-type detector. As such, it may be used as a long-lived standard to calibrate instruments such as well scintillation spectrometers in which measurements are to be made involving iodine-125

  3. Radiation processing of carbon fiber-acrylated epoxy composites

    International Nuclear Information System (INIS)

    Singh, A.; Saunders, C.B.

    1992-01-01

    Advanced composites, specifically carbon fiber reinforced epoxies, are being used for a variety of demanding structural applications, primarily because of their high strength-to-weight and stiffness-to-weight ratios, corrosion resistance, and damage tolerance characteristics. For these composites the key advantages of using electron beam (EB), rather than thermal curing, are curing at ambient temperature, reduced curing times for individual components, improved resin stability, fewer volatiles, and better control of the profile of energy absorption. Epoxy compounds do, however, have to be modified to make them EB curable. The electron beam penetration limit, a function of beam energy, product density, and the thickness of any container required, must also be examined when considering EB processing. Research is being conducted to develop EB-curable carbon fiber-acrylated epoxy composites. The tensile properties of these laminates are comparable to those of thermally cured epoxy laminates. Research is continuing to develop suitable resin formulations and coupling agents to optimize the mechanical properties of EB-cured carbon fiber laminates. In this chapter the EB curing of epoxies, processing considerations, and typical properties of EB-cured carbon fiber-acrylated epoxy laminates are discussed. (orig.)

  4. Iodine deficiency disorders in Sarawak, Malaysia.

    Science.gov (United States)

    Kiyu, A; Tambi, Z; Ahmad, Y

    1998-12-01

    The state of Sarawak in Malaysia has a high prevalence of iodine deficiency disorders (IDD). This has been revealed through a review of goitre surveys that were carried out in the State from the early 1970s to the 1990s. The primary cause was low iodine intake. Contributory factors were low iodine content in the soil and water as well as high cassava consumption. Virtual elimination of IDD is one of the nutritional goals of the IDD prevention and control programs. The strategies adopted include the iodination of coarse salt, which is sold in the market by shopkeepers and also provided free from government health clinics; legislation requiring that salt sold in IDD-gazetted areas must be iodised; and the use of iodinators to iodise water supplied by the gravity-feed system to villages and boarding schools in rural areas. The indicators used in the monitoring and evaluation of the program include the availability of iodised salt in the market and households, iodine levels in water supply that had been fitted with iodinators, goitre volume measured by ultrasound, and urinary iodine excretion among school children.

  5. Conservation problems with paintings containing fluorescent layers of paint

    Directory of Open Access Journals (Sweden)

    Stefanie De Winter

    2010-11-01

    Full Text Available L’artiste moderne cherche continuellement de nouvelles techniques. Des nouveaux matériaux tels que l’éponge, le polyester, le sable, etc. sont devenus courants. Ces développements amènent de nouveaux problèmes dans le domaine de la conservation (préventive des matériaux en question. Chaque matériau doit être analysé individuellement afin de préserver  le mieux possible l’intention de l’artiste à long terme. La présente recherche concerne des matériaux très récents: les pigments et les couleurs fluorescentes. Ces derniers n’ont fait leur apparition qu’au vingtième siècle. Pour cette raison les données concernant leur dégradation et leur conservation sont peu nombreuses. La majorité des tableaux fluorescents sont conçus pour être montrés sous éclairage UV. En cas de dommage, si l’œuvre a besoin d’être retouchée, ceci pose un grand problème esthétique. La retouche devient visible sous les lampes UV. La première partie de la recherche concerne la composition des différentes sortes de pigments et de peintures. Par la suite, les différentes causes de dégradation- lumière UV, chaleur, etc.- sont analysées en détail. Pour conclure, un possible remède est proposé.In modern art we can see that artists are breaking with traditional techniques. New materials like sponge, polyester, sand, etc. are being used. This causes a lot of new problems in the (preventive conservation of works containing these materials. Every material needs to be researched individually so the exact intention of the artist can be preserved for a (relatively long period. My research is about very recent materials: fluorescent pigments and paints. These only started to be used by artists from the 60’s. That's why there is not much information about their aging and ways to (preventively conserve them. A lot of fluorescent paintings are meant to be shown under UV-light. If a fluorescent painting has damage and needs to be retouched

  6. LSST Painting Risk Evaluation Memo

    Energy Technology Data Exchange (ETDEWEB)

    Wolfe, Justin E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2016-11-10

    The optics subsystem is required to paint the edges of optics black where possible. Due to the risks in applying the paint LSST requests a review of the impact of removing this requirement for the filters and L3.

  7. Iodine in soil

    International Nuclear Information System (INIS)

    Johanson, Karl Johan

    2000-12-01

    A literature study of the migration and the appearance of iodine isotopes in the bio-sphere particularly in soil is presented. Some important papers in the field of iodine appearance in soil and the appearance of 129 I in the surroundings of reprocessing plants are discussed. The most important conclusions are: 1. Iodine binds to organic matter in the soil and also to some oxides of aluminium and iron. 2. If the iodine is not bound to the soil a large fraction of added 129 I is volatilized after a rather short period. 3. The binding and also the volatilisation seems to be due to biological activity in the soil. It may take place within living microorganisms or by external enzymes excreted from microorganisms. 4. Due to variations in the composition of soil there may be a large variation in the distribution of 129 I in the vertical profile of soil - usually most of the 129 I in the upper layer - which also results in large variations in the 129 I uptake to plants

  8. Iodine in soil

    Energy Technology Data Exchange (ETDEWEB)

    Johanson, Karl Johan [Swedish Univ. of Agricultural Sciences, Uppsala (Sweden). Dept. of Forest Mycology and Pathology

    2000-12-01

    A literature study of the migration and the appearance of iodine isotopes in the bio-sphere particularly in soil is presented. Some important papers in the field of iodine appearance in soil and the appearance of {sup 129}I in the surroundings of reprocessing plants are discussed. The most important conclusions are: 1. Iodine binds to organic matter in the soil and also to some oxides of aluminium and iron. 2. If the iodine is not bound to the soil a large fraction of added {sup 129}I is volatilized after a rather short period. 3. The binding and also the volatilisation seems to be due to biological activity in the soil. It may take place within living microorganisms or by external enzymes excreted from microorganisms. 4. Due to variations in the composition of soil there may be a large variation in the distribution of {sup 129}I in the vertical profile of soil - usually most of the {sup 129}I in the upper layer - which also results in large variations in the {sup 129}I uptake to plants.

  9. Thermal-mechanical properties of a graphitic-nanofibers reinforced epoxy.

    Science.gov (United States)

    Salehi-Khojin, Amin; Jana, Soumen; Zhong, Wei-Hong

    2007-03-01

    We previously developed a series of reactive graphitic nanofibers (r-GNFs) reinforced epoxy (nano-epoxy) as composite matrices, which have shown good wetting and adhesion properties with continuous fiber. In this work, the thermal-mechanical properties of the nano-epoxy system containing EponTM Resin 828 and Epi-cure Curing Agent W were characterized. Results from three-point bending tests showed that the flexural strength and flexural modulus of this system with 0.30 wt% of reactive nanofibers were increased by 16%, and 21% respectively, over pure epoxy. Fracture toughness increased by ca. 40% for specimens with 0.50 wt% of r-GNFs. By dynamic mechanical analysis (DMA) test, specimens with 0.30 wt% of r-GNFs showed a significant increase in storage modulus E' (by ca. 122%) and loss modulus E" (by ca. 111%) with respect to that of pure epoxy. Also thermo-dilatometry analysis (TDA) was used to measure dimensional change of specimens as a function of temperature, and then, coefficients of thermal expansion (CTE) before and after glass transition temperature (Tg) were obtained. Results implied that nano-epoxy materials had good dimensional stability and reduced CTE values when compared to those of pure epoxy.

  10. Intravascular enhancement with identical iodine delivery rate using different iodine contrast media in a circulation phantom.

    Science.gov (United States)

    Mihl, Casper; Wildberger, Joachim E; Jurencak, Tomas; Yanniello, Michael J; Nijssen, Estelle C; Kalafut, John F; Nalbantov, Georgi; Mühlenbruch, Georg; Behrendt, Florian F; Das, Marco

    2013-11-01

    Both iodine delivery rate (IDR) and iodine concentration are decisive factors for vascular enhancement in computed tomographic angiography. It is unclear, however, whether the use of high-iodine concentration contrast media is beneficial to lower iodine concentrations when IDR is kept identical. This study evaluates the effect of using different iodine concentrations on intravascular attenuation in a circulation phantom while maintaining a constant IDR. A circulation phantom with a low-pressure venous compartment and a high-pressure arterial compartment simulating physiological circulation parameters was used (heart rate, 60 beats per minute; stroke volume, 60 mL; blood pressure, 120/80 mm Hg). Maintaining a constant IDR (2.0 g/s) and a constant total iodine load (20 g), prewarmed (37°C) contrast media with differing iodine concentrations (240-400 mg/mL) were injected into the phantom using a double-headed power injector. Serial computed tomographic scans at the level of the ascending aorta (AA), the descending aorta (DA), and the left main coronary artery (LM) were obtained. Total amount of contrast volume (milliliters), iodine delivery (grams of iodine), peak flow rate (milliliter per second), and intravascular pressure (pounds per square inch) were monitored using a dedicated data acquisition program. Attenuation values in the AA, the DA, and the LM were constantly measured (Hounsfield unit [HU]). In addition, time-enhancement curves, aortic peak enhancement, and time to peak were determined. All contrast injection protocols resulted in similar attenuation values: the AA (516 [11] to 531 [37] HU), the DA (514 [17] to 531 [32] HU), and the LM (490 [10] to 507 [17] HU). No significant differences were found between the AA, the DA, and the LM for either peak enhancement (all P > 0.05) or mean time to peak (AA, 19.4 [0.58] to 20.1 [1.05] seconds; DA, 21.1 [1.0] to 21.4 [1.15] seconds; LM, 19.8 [0.58] to 20.1 [1.05] seconds). This phantom study demonstrates that

  11. Internal contamination by tritium caused by radioluminescent paints

    Energy Technology Data Exchange (ETDEWEB)

    Adamiak-Ziemba, J.; Doniec, J.

    1985-01-01

    The internal contamination investigations covered 23 persons using radioluminescence paints containing tritium, assembling devices painted with those paints, and those having no contact with active paints but working next to the painting room. Determined were concentrations of tritium excreted with urine, air contamination at workplaces, contamination of workplace areas and hand skin. At the time covered by the investigations, the mean annual equivalent doses for those using tritium paints were reduced from 14-20 mSv to about 5 mSv. In those working next to the painting room they were reduced from 5.8-15 to 0.23 mSv. The exposure of those assembling the devices does not exceed 1 mSv. It was demonstrated that the main cause of the tritium exposure level was air contamination in working rooms.

  12. Study of Iodine Prophylaxis Following Nuclear Accidents

    International Nuclear Information System (INIS)

    Sri Widayati; Tedjasari, R. S.; Elfida

    2007-01-01

    Study of iodine prophylaxis following nuclear accidents has been done. Giving stable iodine to a population exposed by I-131 is one of preventive action from internal radiation to the thyroid gland. Stable iodine could be given as Kl tablet in a range of dose of 30 mg/day to 130 mg/day. Improper giving of stable iodine could cause side effect to health, so then some factors should be considered i. e. dose estimation, age, dose of stable iodine to be given, duration of stable iodine prophylaxis and risk of health. (author)

  13. Theoretical and experimental investigations on the behaviour of iodine during severe accidents: volatile iodine. Final report

    International Nuclear Information System (INIS)

    Funke, F.; Zeh, P.; Greger, G.U.; Hellmann, S.

    1999-01-01

    Analysis of the consequences of severe accidents in nuclear power plants requires knowledge of the behaviour of radionuclides relevant from the radiological viewpoint, especially the iodine. The current modelling of iodine behaviour is not conclusive, owing to insufficiently known data. This project is intended to eliminate some of these data gaps in critical areas. 350 tests on the radiation-induced oxidation of elemental iodine (I 2 ) in the containment atmosphere were performed yielding an extended database. Moreover, irradiation tests were performed on the formation and decomposition of ozone which is a reaction partner for I 2 . The reaction with ozone converts volatile I 2 into non-volatile iodine oxides or iodate. An improved kinetic modelling was developed for the iodine accident code IMPAIR. Now the model is valid also for steam-containing atmospheres and, additionally, considers dose rate and thus the actual ozone concentration. An assessment of the literature concludes that β and γ radiation have no different impact on iodine chemistry and thus do not need to be modelled separately in iodine accident codes. An assessment of the literature shows a partly significant chemical interaction of volatile iodine with aerosols. Since such reactions lead to a faster decrease of volatile iodine at least at high aerosol concentrations, a modelling should be foreseen in the future. In the frame of the international ISP-41 project, calculations to an integral test in the Canadian Radioiodine Test Facility (RTF) were performed with IMPAIR. The existing model of the radiation-induced I 2 formation in the sump in IMPAIR is identified as a weakness requiring future improvement. A theoretical assessment on the iodine chemistry in the droplets of a spray system concludes that a modelling is necessary in case of spraying with fresh water, and that this is already contained in available spray models. During recirculation spraying in an examplary, hypothetical EPR case, no

  14. Green Preparation of Epoxy/Graphene Oxide Nanocomposites Using a Glycidylamine Epoxy Resin as the Surface Modifier and Phase Transfer Agent of Graphene Oxide.

    Science.gov (United States)

    Tang, Xinlei; Zhou, Yang; Peng, Mao

    2016-01-27

    In studies of epoxy/graphene oxide (GO) nanocomposites, organic solvents are commonly used to disperse GO, and vigorous mechanical processes and complicated modification of GO are usually required, increasing the cost and hindering the development and application of epoxy nanocomposites. Here, we report a green, facile, and efficient method of preparing epoxy/GO nanocomposites. When triglycidyl para-aminophenol (TGPAP), a commercially available glycidyl amine epoxy resin with one tertiary amine group per molecule, is used as both the surface modifier and phase transfer agent of GO, GO can be directly and rapidly transferred from water to diglycidyl ether of bisphenol A and other types of epoxy resins by manual stirring under ambient conditions, whereas GO cannot be transferred to these epoxy resins in the absence of TGPAP. The interaction between TGPAP and GO and the effect of the TGPAP content on the dispersion of GO in the epoxy matrix were investigated systematically. Superior dispersion and exfoliation of GO nanosheets and remarkably improved mechanical properties, including tensile and flexural properties, toughness, storage modulus, and microhardness, of the epoxy/GO nanocomposites with a suitable amount of TGPAP were demonstrated. This method is organic-solvent-free and technically feasible for large-scale preparation of high-performance nanocomposites; it opens up new opportunities for exploiting the unique properties of graphene or even other nanofillers for a wide range of applications.

  15. Intrinsic Flame-Retardant and Thermally Stable Epoxy Endowed by a Highly Efficient, Multifunctional Curing Agent

    Directory of Open Access Journals (Sweden)

    Chunlei Dong

    2016-12-01

    Full Text Available It is difficult to realize flame retardancy of epoxy without suffering much detriment in thermal stability. To solve the problem, a super-efficient phosphorus-nitrogen-containing reactive-type flame retardant, 10-(hydroxy(4-hydroxyphenylmethyl-5,10-dihydrophenophosphazinine-10-oxide (HB-DPPA is synthesized and characterized. When it is used as a co-curing agent of 4,4′-methylenedianiline (DDM for curing diglycidyl ether of bisphenol A (DGEBA, the cured epoxy achieves UL-94 V-0 rating with the limiting oxygen index of 29.3%. In this case, the phosphorus content in the system is exceptionally low (0.18 wt %. To the best of our knowledge, it currently has the highest efficiency among similar epoxy systems. Such excellent flame retardancy originates from the exclusive chemical structure of the phenophosphazine moiety, in which the phosphorus element is stabilized by the two adjacent aromatic rings. The action in the condensed phase is enhanced and followed by pressurization of the pyrolytic gases that induces the blowing-out effect during combustion. The cone calorimeter result reveals the formation of a unique intumescent char structure with five discernible layers. Owing to the super-efficient flame retardancy and the rigid molecular structure of HB-DPPA, the flame-retardant epoxy acquires high thermal stability and its initial decomposition temperature only decreases by 4.6 °C as compared with the unmodified one.

  16. Performance of epoxy-nanocomposite under corrosive environment

    Directory of Open Access Journals (Sweden)

    2007-06-01

    Full Text Available Nanocomposite materials consisting of polymeric matrix materials and natural or synthetic layered minerals like clay are currently an expanding field of study because these new materials often exhibit a wide range of improved properties over their unmodified starting polymers. Epoxy/organoclay nanocomposites have been prepared by intercalating epoxy into the organoclay via direct mixing process. The clay exfoliation was monitored by X-ray diffraction (XRD and transmission electron microscopy (TEM. Water diffusion and sulfuric acid corrosion resistance of epoxy-based nanocomposites were evaluated. Diffusion was studied through epoxy samples containing up to 6 phr (parts per hundred resin of an organically treated montmorillonite. The diffusion of the environmental solution was measured by noting the increase in weight of the samples as a function of immersion time in these solutions at 80°C. The effect of the degree of exfoliation of the organoclay on water barrier and corrosion resistance was specifically studied. The data have been compared to those obtained from the neat epoxy resin to evaluate the diffusion properties of the nanocomposites. The flexural strength of the epoxy/organoclay nanocomposites samples made was examined to compare their mechanical performance under corrosive conditions as a function of immersion time and temperature. It was found, that the organoclay was mainly intercalated with some exfoliation and that addition of the organoclay yields better flexural strength retention under immersion into sulfuric acid.

  17. In-situ Elevated Temperature Mechanical Performance of MWCNT/epoxy Nanocomposite

    Directory of Open Access Journals (Sweden)

    Bhanu Pratap Singh

    2017-03-01

    Full Text Available The present investigation has been focused on the effects of multi-walled carbon nanotube (MWCNT addition on the mechanical performance of epoxy under different in-service elevated temperature environments. Room temperature flexural test results revealed that addition of 0.1 wt. % MWCNT into epoxy resin resulted in modulus and strength enhancement of 21 % and 9 % respectively. With increase in service temperature, significant decrement in both modulus and strength was noticed for both materials (neat epoxy and MWCNT/epoxy nanocomposite, but the rate of degradation was found to be quite drastic for the nanocomposite. At 90 °C temperature, the CNT/epoxy nanocomposite exhibited inferior modulus and strength, which are 41 % and 59 % lower than neat epoxy respectively. The variation trend in elastic modulus with temperature obtained from both flexural testing and DMA for both these materials was also analyzed. It was found that addition of 0.1 % CNT in the epoxy reduced the glass transition temperature by about 16°C.

  18. Iodine deficiency in pregnancy and the effects of maternal iodine supplementation on the offspring: a review

    NARCIS (Netherlands)

    Zimmermann, M.B.

    2009-01-01

    The World Health Organization (WHO) recently increased their recommended iodine intake during pregnancy from 200 to 250 µg/d and suggested that a median urinary iodine (UI) concentration of 150-249 µg/L indicates adequate iodine intake in pregnant women. Thyrotropin concentrations in blood collected

  19. Neural correlates of viewing paintings

    DEFF Research Database (Denmark)

    Vartanian, Oshin; Skov, Martin

    2014-01-01

    Many studies involving functional magnetic resonance imaging (fMRI) have exposed participants to paintings under varying task demands. To isolate neural systems that are activated reliably across fMRI studies in response to viewing paintings regardless of variation in task demands, a quantitative...

  20. Iodine-125 and Iodine-131 in the Thames Valley and other areas

    International Nuclear Information System (INIS)

    Howe, J.R.; Lloyd, M.K.; Bowlt, C.

    1985-01-01

    Part of the Iodine-125 and Iodine-131 waste from hospitals and research centres is discarded down drains and passes through sewage and water reclamation works into the river system. Relatively high concentration of radioiodine occur in outfalls that discharge into the river Thames, lower levels are found in the mainstream river and less still in the reservoirs and tap water supplies abstracted from the river. The pathway from waste to drinking water could account for the low levels of Iodine-125 found in the thyroid glands of some farm animals and human beings in the Thames valley

  1. Evaluation of soil-plant transfer factors of iodine. Estimation of annual ingestion for iodine from the diet

    International Nuclear Information System (INIS)

    Saas, Arsene.

    1980-11-01

    The author presents the iodine middle contents of the soils and vegetables. A synthesis on the iodine evolution in the soils and vegetables allows to conclude that the vegetable absorption of this isotope is correlated with the isotopiquely exchangeable iodine of the soil. The soil-plant transfer-factors are calculated for the vegetables, cereals, fruits from the stable iodine quantitative analysis. The annual iodine ingestion has been estimated from the dietary of the European Communites areas. This one is a little different of the quantity estimated by CRESTA-LACOURLY-R 2979, yet the contribution by consummation unity is different [fr

  2. New biocides for antifouling paints

    International Nuclear Information System (INIS)

    Mazziotti, Isabella; Massanisso, Paolo; Cremisini, Carlo; Chiavarini, Salvatore; Fantini, Michele; Morabito, Roberto

    2005-01-01

    The antifouling paints are used for protecting the hulls of the boasts from the undesirable accumulation of micro-organisms, plants, and animals on artificial surfaces (marine biological fouling). These paints constitute a potential risk for the marine environment, because of the presence in their formulation, among the other potentially toxic components, of organic compounds acting as biocide. The environmental problems associated with the use of the organotin compounds as biocides in the antifouling paints, have lead to the international ban of these compounds. In the article the new antifouling paints coming up the national and international market are shortly introduced and discussed, with particular attention respect to the new organic compounds used as biocides. In Italy quite a few marine monitoring campaigns have been carried out for organotin compounds, on the contrary there is a lack of data regarding the presence of other biocides [it

  3. Modeling of a solar-pumped iodine laser

    Science.gov (United States)

    Wilson, J. W.; Lee, J. H.

    1980-01-01

    The direct conversion in space of solar radiation into laser radiation for power transmission to earth, satellites, or deep space probes shows promise as a reasonably simple technology and may have cost advantage in deployment and greater reliability compared to other methods of space power generation and transmission. The main candidates for solar pumping are the gas dynamic, photochemical, and direct photoexcited lasers. Here consideration is given to the photochemical reaction of alkyliodides which predominantly excite the I(2P1/2) state which then lases at 1.315 microns. The iodine ground state is eventually lost to reconstituting the gas or in the formation of molecular iodine. The rates at which the gas is required to be recycled through the laser system are modest. The side exposure at 100-fold solar concentration of a 100-m long tube with a 1 sq m cross section is estimated to provide 20 kW of continuous laser output. Scaling laws and optimum operating conditions of this system are discussed.

  4. Compositional and quantitative microtextural characterization of historic paintings by micro-X-ray diffraction and Raman microscopy.

    Science.gov (United States)

    Romero-Pastor, Julia; Duran, Adrian; Rodríguez-Navarro, Alejandro Basilio; Van Grieken, René; Cardell, Carolina

    2011-11-15

    This work shows the benefits of characterizing historic paintings via compositional and microtextural data from micro-X-ray diffraction (μ-XRD) combined with molecular information acquired with Raman microscopy (RM) along depth profiles in paint stratigraphies. The novel approach was applied to identify inorganic and organic components from paintings placed at the 14th century Islamic University-Madrasah Yusufiyya-in Granada (Spain), the only Islamic University still standing from the time of Al-Andalus (Islamic Spain). The use of μ-XRD to obtain quantitative microtextural information of crystalline phases provided by two-dimensional diffraction patterns to recognize pigments nature and manufacture, and decay processes in complex paint cross sections, has not been reported yet. A simple Nasrid (14th century) palette made of gypsum, vermilion, and azurite mixed with glue was identified in polychromed stuccos. Here also a Christian intervention was found via the use of smalt, barite, hematite, Brunswick green and gold; oil was the binding media employed. On mural paintings and wood ceilings, more complex palettes dated to the 19th century were found, made of gypsum, anhydrite, barite, dolomite, calcite, lead white, hematite, minium, synthetic ultramarine blue, and black carbon. The identified binders were glue, egg yolk, and oil.

  5. Chemical oxygen-iodine laser with atomic iodine generated via fluorine atoms

    Czech Academy of Sciences Publication Activity Database

    Jirásek, Vít; Čenský, Miroslav; Špalek, Otomar; Kodymová, Jarmila; Picková, Irena; Jakubec, Ivo

    2008-01-01

    Roč. 345, č. 1 (2008), 14-22 ISSN 0301-0104 R&D Projects: GA ČR GA202/05/0359 Institutional research plan: CEZ:AV0Z10100523; CEZ:AV0Z40320502 Keywords : atomic iodine * atomic fluorine * chemical oxygen–iodine laser * COIL Subject RIV: BH - Optics, Masers, Lasers Impact factor: 1.961, year: 2008

  6. Mural Painting as Inclusive Art Learning Experience

    Science.gov (United States)

    Ho, Kong

    2010-01-01

    Traditional art education, like other academic disciplines, emphasizes competitiveness and individualism. Through a mural painting curriculum, learners participate in mural art and history appreciation, are active in mural theme or content construction, and engage in hands-on mural design and painting processes. When mural paintings are produced…

  7. Texton-based analysis of paintings

    NARCIS (Netherlands)

    Van der Maaten, L.J.P.; Postma, E.O.

    2010-01-01

    The visual examination of paintings is traditionally performed by skilled art historians using their eyes. Recent advances in intelligent systems may support art historians in determining the authenticity or date of creation of paintings. In this paper, we propose a technique for the examination of

  8. Mineral resource of the month: iodine

    Science.gov (United States)

    Polyak, Désirée E.

    2009-01-01

    The article focuses on iodine, its benefits and adverse effects, and its production and consumption. It states that iodine is essential to humans for it produces thyroid hormones to nourish thyroid glands but excessive intake could cause goiter, hyperthyroidism or hypothyroidism. U.S. laws require salt iodization to help prevent diseases. Chile and Japan are the world's leading iodine producer while in the U.S. iodine is mined from deep well brines in northern Oklahoma.

  9. An investigation of the electrochemical action of the epoxy zinc-rich coatings containing surface modified aluminum nanoparticle

    Science.gov (United States)

    Jalili, M.; Rostami, M.; Ramezanzadeh, B.

    2015-02-01

    Aluminum nanoparticle was modified with amino trimethylene phosphonic acid (ATMP). The surface characterization of the nanoparticles was done by X-ray photo electron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and thermal gravimetric analysis. The influence of the replacement of 2 wt% of zinc dust in the standard zinc-rich epoxy coating by nanoparticles on the electrochemical action of the coating was studied by electrochemical impedance spectroscopy (EIS) and salt spray tests. The morphology and phase composition of the zinc rich paints were evaluated by X-ray diffraction (XRD) and filed-emission scanning electron microscopy (FE-SEM). Results showed that the ATMP molecules successfully adsorbed on the surface of Al nanoparticles. Results obtained from salt spray and electrochemical measurements revealed that the addition of surface modified nanoparticles to the zinc rich coating enhanced its galvanic action and corrosion protection properties.

  10. Iodine binding to humic acid.

    Science.gov (United States)

    Bowley, H E; Young, S D; Ander, E L; Crout, N M J; Watts, M J; Bailey, E H

    2016-08-01

    The rate of reactions between humic acid (HA) and iodide (I(-)) and iodate (IO3(-)) have been investigated in suspensions spiked with (129)I at concentrations of 22, 44 and 88 μg L(-1) and stored at 10 °C. Changes in the speciation of (129)I(-), (129)IO3(-) and mixed ((129)I(-) + (129)IO3(-)) spikes were monitored over 77 days using liquid chromatography inductively coupled plasma mass spectrometry (LC-ICP-MS). In suspensions spiked with (129)I(-) 25% of the added I(-) was transformed into organic iodine (Org-(129)I) within 77 days and there was no evidence of (129)IO3(-) formation. By contrast, rapid loss of (129)IO3(-) and increase in both (129)I(-) and Org-(129)I was observed in (129)IO3(-)-spiked suspensions. However, the rate of Org-(129)I production was greater in mixed systems compared to (129)IO3(-)-spiked suspensions with the same total (129)I concentration, possibly indicating IO3(-)I(-) redox coupling. Size exclusion chromatography (SEC) demonstrated that Org-(129)I was present in both high and low molecular weight fractions of the HA although a slight preference to bond with the lower molecular weight fractions was observed indicating that, after 77 days, the spiked isotope had not fully mixed with the native (127)I pool. Iodine transformations were modelled using first order rate equations and fitted rate coefficients determined. However, extrapolation of the model to 250 days indicated that a pseudo-steady state would be attained after ∼200 days but that the proportion of (129)I incorporated into HA was less than that of (127)I indicating the presence of a recalcitrant pool of (127)I that was unavailable for isotopic mixing. Copyright © 2016 Elsevier Ltd. All rights reserved.

  11. Large-scale quantitative analysis of painting arts.

    Science.gov (United States)

    Kim, Daniel; Son, Seung-Woo; Jeong, Hawoong

    2014-12-11

    Scientists have made efforts to understand the beauty of painting art in their own languages. As digital image acquisition of painting arts has made rapid progress, researchers have come to a point where it is possible to perform statistical analysis of a large-scale database of artistic paints to make a bridge between art and science. Using digital image processing techniques, we investigate three quantitative measures of images - the usage of individual colors, the variety of colors, and the roughness of the brightness. We found a difference in color usage between classical paintings and photographs, and a significantly low color variety of the medieval period. Interestingly, moreover, the increment of roughness exponent as painting techniques such as chiaroscuro and sfumato have advanced is consistent with historical circumstances.

  12. Prediction of brittle fracture of epoxy-aluminum flanging

    Directory of Open Access Journals (Sweden)

    Korbel J.

    2010-07-01

    Full Text Available This paper presents a fracture mechanical approach for estimation of critical bending load of different types of aluminum-epoxy flanging and comparison with experimental measurements. For this purpose, several designs of the flanges were investigated. The flanges were glued to the epoxy bars and adhesive-epoxy interface was considered as a bi-material notch. Prediction of the failure is based on generalized stress intensity factor and generalized fracture toughness.

  13. Accelerated thermal aging of rubber modified epoxy encapsulants

    International Nuclear Information System (INIS)

    Sayre, J.A.

    1979-01-01

    A program is outlined to enable prediction of physical properties of rubber modified epoxy encapsulants over the life time of the extended life neutron generators. Preliminary results show that the chief aging phenomenon occurring is increased crosslink density of the epoxy matrix. No changes in the rubber phase have been detected. The effect of increased epoxy crosslink density has been higher volume resistivity at 66 0 C, increased tensile strength, and decreased ultimate elongation

  14. Chiral smectogens with four-phenyl-ring molecular core, laterally substituted by iodine atom

    Czech Academy of Sciences Publication Activity Database

    Podoliak, Natalia; Novotná, Vladimíra; Kašpar, Miroslav; Hamplová, Věra; Pacherová, Oliva

    2015-01-01

    Roč. 42, č. 3 (2015), s. 404-411 ISSN 0267-8292 R&D Projects: GA ČR GA13-14133S; GA MŠk(CZ) LD14007 Institutional support: RVO:68378271 Keywords : liquid crystals * iodine lateral substitution * lactic acid unit * ferroelectric phase Subject RIV: JJ - Other Materials Impact factor: 2.244, year: 2015

  15. The Swiss lodized Salt Program Provides Adequate Iodine for School Children and Pregnant Women, but Weaning Infants Not Receiving Iodine-Containing Complementary Foods as well as Their Mothers Are Iodine Deficient

    NARCIS (Netherlands)

    Andersson, M.; Aeberli, I.; Wüst, N.; Piacenza, A.M.; Bucher, T.; Henschen, I.; Haldimann, M.; Zimmermann, M.B.

    2010-01-01

    Background: If children and pregnant women in the population are iodine sufficient, it is generally assumed infants are also sufficient. But weaning infants may be at risk of iodine deficiency because iodized salt contributes little dietary iodine during this period. To fill this gap, iodine

  16. Iodine behaviour in severe accidents

    Energy Technology Data Exchange (ETDEWEB)

    Dutton, L M.C.; Grindon, E; Handy, B J; Sutherland, L [NNC Ltd., Knutsford (United Kingdom); Bruns, W G; Sims, H E [AEA Technology, Harwell (United Kingdom); Dickinson, S [AEA Technology, Winfrith (United Kingdom); Hueber, C; Jacquemain, D [IPSN/CEA, Cadarache, Saint Paul-Lez-Durance (France)

    1996-12-01

    A description is given of analyses which identify which aspects of the modelling and data are most important in evaluating the release of radioactive iodine to the environment following a potential severe accident at a PWR and which identify the major uncertainties which affect that release. Three iodine codes are used namely INSPECT, IODE and IMPAIR, and their predictions are compared with those of the PSA code MAAP. INSPECT is a mechanistic code which models iodine behaviour in the aqueous aerosol, spray water and sump water, and the partitioning of volatile species between the aqueous phases and containment gas space. Organic iodine is not modelled. IODE and IMPAIR are semi-empirical codes which do not model iodine behaviour in the aqueous aerosol, but model organic iodine. The fault sequences addressed are based on analyses for the Sizewell `B` design. Two types of sequence have been analysed.: (a) those in which a major release of fission products from the primary circuit to the containment occur, e.g. a large LOCAS, (b) those where the release by-passes the containment, e.g. a leak into the auxiliary building. In the analysis of the LOCA sequences where the pH of the sump is controlled to be a value of 8 or greater, all three codes predict that the oxidation of iodine to produce gas phase species does not make a significant contribution to the source term due to leakage from the reactor building and that the latter is dominated by iodide in the aerosol. In the case where the pH of the sump is not controlled, it is found that the proportion of gas phase iodine increases significantly, although the cumulative leakage predicted by all three codes is not significantly different from that predicted by MAAP. The radiolytic production of nitric acid could be a major factor in determining the pH, and if the pH were reduced, the codes predict an increase in gas phase iodine species leaked from the containment. (author) 4 figs., 7 tabs., 13 refs.

  17. Examination of lead concentrations in new decorative enamel paints in four countries with different histories of activity in lead paint regulation

    International Nuclear Information System (INIS)

    Clark, C. Scott; Kumar, Abhay; Mohapatra, Piyush; Rajankar, Prashant; Nycz, Zuleica; Hambartsumyan, Amalia; Astanina, Lydia; Roda, Sandy; Lind, Caroline; Menrath, William; Peng, Hongying

    2014-01-01

    Paints with high lead concentrations (ppm) continue to be sold around the world in many developing countries and those with economies in transition representing a major preventable environmental health hazard that is being increased as the economies expand and paint consumption is increasing. Prior lead paint testing had been performed in Brazil and India and these countries were selected to examine the impact of a new regulatory limit in Brazil and the impact of efforts of non-governmental organizations and others to stop the use of lead compounds in manufacturing paints. Armenia and Kazakhstan, in Central Asia, were selected because no information on lead concentration in those regions was available, no regulatory activities were evident and non-governmental organizations in the IPEN network were available to participate. Another objective of this research was to evaluate the lead loading (µg/cm 2 ) limit determined by X-Ray Fluorescence (XRF) for areas on toys that are too small to obtain a sample of sufficient size for laboratory analysis. The lead concentrations in more than three-fourths of the paints from Armenia and Kazakhstan exceeded 90 ppm, the limit in the United States, and 600 ppm, the limit in Brazil. The percentages were about one-half as high in Brazil and India. The average concentration in paints purchased in Armenia, 25,000 ppm, is among the highest that has been previously reported, that in Kazakhstan, 15,700 ppm, and India, 16,600, about median. The average concentration in Brazil, 5600 ppm, is among the lowest observed. Paints in Brazil that contained an average of 36,000 ppm before the regulatory limit became effective were below detection (<9 ppm) in samples collected in the current study. The lack of any apparent public monitoring of paint lead content as part of regulatory enforcement makes it difficult to determine whether the regulation was a major factor contributing to the decline in lead use in these paints. Using data from the

  18. Iodine in Enteral and Parenteral Nutrition

    NARCIS (Netherlands)

    Zimmermann, M.B.; Crill, C.M.

    2010-01-01

    Iodine deficiency (ID) has multiple adverse effects on growth and development due to inadequate thyroid hormone production. Methods for assessment of iodine nutrition in individuals include the urinary iodine concentration (UI), thyroid size and thyroid function tests. The UI measured in several

  19. Iodine chemistry in a reactor regulation

    Energy Technology Data Exchange (ETDEWEB)

    Powers, D A [Nuclear Regulatory Commission, Washington, DC (United States). Advisory Committee on Reactor Safeguards

    1996-12-01

    Radioactive iodine has always been an important consideration in the regulation of nuclear power reactors to assure the health and safety of the public. Regulators adopted conservatively bounding predictions of iodine behavior in the earliest days of the development of nuclear power because there was so little known about either accidents or the chemistry of iodine. Today there is a flood of new information and understanding of the chemistry of iodine under reactor accident conditions. This paper offers some thoughts on how the community of scientists engaged in the study of iodine chemistry can present the results of their work so that it is more immediately adopted by the regulator. It is suggested that the scientific community consider the concept of consensus standards so effectively used within the engineering community to define the status of the study of radioactive iodine chemistry for reactor safety. (author) 9 refs.

  20. Iodine chemistry in a reactor regulation

    International Nuclear Information System (INIS)

    Powers, D.A.

    1996-01-01

    Radioactive iodine has always been an important consideration in the regulation of nuclear power reactors to assure the health and safety of the public. Regulators adopted conservatively bounding predictions of iodine behavior in the earliest days of the development of nuclear power because there was so little known about either accidents or the chemistry of iodine. Today there is a flood of new information and understanding of the chemistry of iodine under reactor accident conditions. This paper offers some thoughts on how the community of scientists engaged in the study of iodine chemistry can present the results of their work so that it is more immediately adopted by the regulator. It is suggested that the scientific community consider the concept of consensus standards so effectively used within the engineering community to define the status of the study of radioactive iodine chemistry for reactor safety. (author) 9 refs

  1. Iodine Prophylaxis and Nuclear Accidents

    International Nuclear Information System (INIS)

    Franic, Z.

    1998-01-01

    Iodine is a highly volatile element therefore being very mobile in the environment. It enters the metabolism of living organisms and is selectively taken up and concentrated in the thyroid gland. The plume (cloud-like formation) of radioactive material that might be released in the environment in the case of a serious nuclear accident, primarily consists of the radioactive isotopes of iodine. Among those, due to its decay properties, is the most important 131 I. The effective means of protecting the thyroid gland against exposure to radioactive iodine is an intake of stable iodine. Therefore, one of the central issues in the emergency planning is to determine whether and at which projected thyroid radiation dose stable iodine should be given to the population. The International Atomic Energy Agency (IAEA) set the generic optimized intervention value for iodine prophylaxis to 100 mGy of avertable committed dose to a thyroid.The prophylaxis is implemented by utilizing the pills of pills of potassium iodine (KI). The efficacy of KI in protecting the thyroid gland depends upon the time of intake relative to the start of exposure to radioactive iodine. The best results are obtained if KI is taken 1-2 hours before or immediately after the start of exposure. The recommended dosage, based upon the study performed by Il'in et.al. is 130 mg/day. KI should be taken at least three days after the acute exposure to radioiodine, to prevent accumulation in a thyroid gland of radioiodine excreted from the other compartments of the body. The largest epidemiological study on the effects of KI prophylaxis ever performed was the one in Poland after the Chernobyl accident. Stable iodine was given as single dose of KI solution to 10.5 million of children and 7 millions of adults. Among children no serious side effects were seen while only two adults (with previously recorded iodine sensitivity) had severe respiratory distresses. Polish experiences showed that rapid response to such

  2. Thermoset epoxy polymers from renewable resources

    Science.gov (United States)

    East, Anthony [Madison, NJ; Jaffe, Michael [Maplewood, NJ; Zhang, Yi [Harrison, NJ; Catalani, Luiz H [Carapicuiba, BR

    2009-11-17

    Novel thermoset epoxy polymers using the bisglycidyl ethers of anhydrosugars, such as isosorbide, isomannide, and isoidide, are disclosed. The bisglycidyl ethers are useful as substitutes for bisphenol A in the manufacture of thermoset epoxy ethers. The anhydrosugars are derived from renewable sources and the bisglycidyl ethers are not xenoestrogenic and the thermoset curing agents are likewise derived form renewable resources.

  3. Understanding the thermal, mechanical and electrical properties of epoxy nanocomposites

    International Nuclear Information System (INIS)

    Sarathi, R.; Sahu, R.K.; Rajeshkumar, P.

    2007-01-01

    In the present work, the electrical, mechanical and thermal properties of epoxy nanocomposite materials were studied. The electrical insulation characteristics were analyzed through short time breakdown voltage test, accelerated electrical ageing test, and by tracking test. The breakdown voltage increases with increase in nano-clay content up to 5 wt%, under AC and DC voltages. The volume resistivity, permittivity and tan(δ) of the epoxy nanocomposites were measured. The Weibull studies indicate that addition of nanoclay upto 5 wt% enhances the characteristic life of epoxy nanocomposite insulation material. The tracking test results indicate that the tracking time is high with epoxy nanocomposites as compared to pure epoxy. Ageing studies were carried out to understand the surface characteristic variation through contact angle measurement. The hydrophobicity of the insulating material was analysed through contact angle measurement. The diffusion coefficients of the material with different percentage of clay in epoxy nanocomposites were calculated. The exfoliation characteristics in epoxy nanocomposites were analyzed through wide angle X-ray diffraction (WAXD) studies. The thermal behaviour of the epoxy nanocomposites was analyzed by carrying out thermo gravimetric-differential thermal analysis (TG-DTA) studies. Heat deflection temperature of the material was measured to understand the stability of the material for intermittent temperature variation. The dynamic mechanical analysis (DMA) results indicated that storage modulus of the material increases with small amount of clay in epoxy resin. The activation energy of the material was calculated from the DMA results

  4. Modeling and mechanical performance of carbon nanotube/epoxy resin composites

    International Nuclear Information System (INIS)

    Srivastava, Vijay Kumar

    2012-01-01

    Highlights: ► The MWCNT fillers are uniformly dispersed in the epoxy resin, which improved the mechanical properties of epoxy resin. ► Modified Halpin–Tsai model is useful to calculate the Young’s modulus of MWCNT/epoxy resin composite. ► The experimental moduli are within the variation of 27% with the theoretical values. -- Abstract: The effect of multi-walled carbon nanotube (MWCNT) addition on mechanical properties of epoxy resin was investigated to obtain the tensile strength, compressive strength and Young’s modulus from load versus displacement graphs. The result shows that the tensile strength, compressive strength and Young’s modulus of epoxy resin were increased with the addition of MWCNT fillers. The significant improvements in tensile strength, compressive strength and Young’s modulus were obtained due to the excellent dispersion of MWCNT fillers in the epoxy resin. The dispersion of MWCNT fillers in epoxy resin was observed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) analysis. Also, Halpin–Tsai model was modified by considering the average diameter of internal/external of multi-walled nanotube and orientation factor (α) to calculate the Young’s modulus of multi-walled carbon nanotubes (MWCNTs)/epoxy resin composite. There was a good correlation between the experimentally obtained Young’s modulus and modified Halpin–Tsai model.

  5. The failure mode of natural silk epoxy triggered composite tubes

    International Nuclear Information System (INIS)

    Eshkour, R A; Ariffin, A K; Zulkifli, R; Sulong, A B; Azhari, C H

    2012-01-01

    In this study the quasi static compression test over natural silk epoxy triggered composite tubes has been carried out, the natural silk epoxy composite tubes consist of 24 layer of woven natural silk as reinforcement and thermoset epoxy resin as matrix which both of them i e natural silk and epoxy have excellent mechanical properties More over the natural silk have better moisture resistance in comparison with other natural reinforcements, the length of tubes are 50, 80 and 120 mm The natural silk epoxy composite tubes are associated with an external trigger which includes 4 steel pieces welded on downside flat plate fixture The hand lay up fabrication method has been used to make the natural silk epoxy composite tubes Instron universal testing machine with 250 KN load capacity has been employed to accomplish this investigation The failure modes of natural silk epoxy triggered composite tubes has been investigated by representative photographs which has been taken by a high resolution camera(12 2 Mp) during the quasi static compression test, from the photographs is observed the failure modes is progressive local buckling

  6. Fracture behaviour of a self-healing microcapsule-loaded epoxy system

    Directory of Open Access Journals (Sweden)

    2011-03-01

    Full Text Available The effect of temperature on the fracture behaviour of a microcapsule-loaded epoxy matrix was investigated. Microencapsulated epoxy and mercaptan-derivative healing agents were incorporated into an epoxy matrix to produce a polymer composite capable of self-healing. Maximum fracture loads were measured using the double-torsion method. Thermal aging at 55 and 110°C for 17 hours [hrs] was applied to heal the pre-cracked samples. The addition of microcapsules appeared to increase significantly the load carrying capacity of the epoxy after healing. Once healed, the composites achieved as much as 93–171% of its virgin maximum fracture load at 18, 55 and 110°C. The fracture behavior of the microcapsule- loaded epoxy matrix was influenced by the healing temperature. The high self-healing efficiency may be attributed to the result of the subsurface micro-crack pinning or deviation, and to a stronger microencapsulated epoxy and mercaptanderivative binder than that of the bulk epoxy. The results show that the healing temperature has a significant effect on recovery of load transferring capability after fracture.

  7. Epoxy/α-alumina nanocomposite with high electrical insulation performance

    Directory of Open Access Journals (Sweden)

    Yun Chen

    2017-10-01

    Full Text Available An experimental study was conducted to improve the electrical insulation of epoxy resin. The effects of boehmite, γ-alumina and α-alumina nanoparticles on the volume resistivity, dielectric strength and glass transition temperature of epoxy nanocomposites were investigated. The results showed that α-alumina nanoparticles displayed obvious advantages in enhancing electrical insulation performance of epoxy nanocomposites, compared to boehmite and γ-alumina nanoparticles. The direct current volume resistivity and breakdown strength of epoxy nanocomposite with 2.0 wt% α-alumina nanoparticles was improved to 2.2 × 1018 Ω cm and 76.1 kV mm−1 respectively. And these improved values of electrical insulation properties are much higher than these of epoxy nanocomposites reported in previous studies. The main reason of these improvements may be that the epoxy/α-alumina interaction zone was enhanced by crosslink. Keywords: Nanocomposite, Epoxy resin, Insulation, α-alumina

  8. Transfer of gaseous iodine to Tradescantia

    International Nuclear Information System (INIS)

    Nakamura, Yuji; Ohmomo, Yoichiro.

    1984-01-01

    Transfer rates of gaseous elemental iodine and methyliodide from atmosphere to Tradescantia were investigated in relation to supposed genetic mutation due to radioactive iodine released from nuclear facilities. The estimated transfer rate of elemental iodine to the young buds of Tradescantia, which was given as the ratio of iodine uptake rate per unit weight of the plant to the concentration of the element in the air, was approximately 7 x 10 -2 cm 3 /g.sec, about 30 to 40 times higher than that of methyliodide. The contribution of direct deposition of elemental iodine was suggested to be significant, although methyliodide was mainly absorbed by respiration through stomata of the plant. (author)

  9. Determination of iodine in Asian diets by epithermal and radiochemical neutron activation analysis

    Czech Academy of Sciences Publication Activity Database

    Kučera, Jan; Iyengar, GV.; Řanda, Zdeněk; Parr, RM.

    2004-01-01

    Roč. 259, č. 3 (2004), s. 505-509 ISSN 0236-5731 R&D Projects: GA AV ČR IAA4048301 Institutional research plan: CEZ:AV0Z1048901 Keywords : iodine * Asian diets Subject RIV: BG - Nuclear, Atomic and Molecular Physics, Colliders Impact factor: 0.457, year: 2004

  10. Selective Clay Placement Within a Silicate-Clay Epoxy Blend Nanocomposite

    Science.gov (United States)

    Miller, Sandi G (Inventor)

    2013-01-01

    A clay-epoxy nanocomposite may be prepared by dispersing a layered clay in an alkoxy epoxy, such as a polypropylene oxide based epoxide before combining the mixture with an aromatic epoxy to improve the nanocomposite's thermal and mechanical properties.

  11. Behavior of highly radioactive iodine on charcoal in moist air

    International Nuclear Information System (INIS)

    Lorenz, R.A.; Manning, S.R.; Martin, W.J.

    1976-01-01

    The behavior of highly radioactive iodine adsorbed on charcoal exposed to moist air (110 torr water vapor partial pressure) was investigated in a series of six experiments. The amount of radioactive 130 I on the well-insulated 28-cm 3 bed ranged from 50 to 570 Ci, and the relative humidity was 47 percent at the bed inlet temperature of 70 0 C. Radioactive iodine was released from the test beds at a continuous fractional release rate of approximately 7 x 10 -6 /hr for all types of charcoal tested. The chemical form of the released iodine was such that it was very highly penetrating with respect to the nine different types of commercial impregnated charcoals tested in backup collection beds. Two types of silver-nitrate-coated adsorption materials behaved similarly to the charcoals. Silver-exchanged type 13-X molecular sieve adsorbers were 20 to 50 times more efficient for adsorbing the highly penetrating iodine, but not as efficient as normally found for collecting methyl iodide. The chemical form of the highly penetrating iodine was not determined. When the moist air velocity was decreased from 28.5 fpm (25 0 C) to as low as 0.71 fpm (25 0 C), the charcoal bed temperature rose slowly and reached the ignition temperature in three of the experiments. At 0.71 fpm (25 0 C) the ignited charcoal beds reached maximum temperatures of 430 to 470 0 C because of the limited oxygen supply. The charcoal exposed for four years at Oak Ridge ignited at 283 0 C compared with 368 0 C for unused charcoal from the same batch. Two of the experiments used charcoal containing 1 or 2 percent TEDA (triethylene-diamine) and a proprietary flame retardant. The oxidation and ignition behavior of these charcoals did not appear to be affected adversely by the presence of the TEDA

  12. Interface Bond Improvement of Sisal Fibre Reinforced Polylactide Composites with Added Epoxy Oligomer.

    Science.gov (United States)

    Hao, Mingyang; Wu, Hongwu; Qiu, Feng; Wang, Xiwen

    2018-03-07

    To improve the interfacial bonding of sisal fiber-reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with addition of a commercial grade epoxy-functionalized oligomer Joncryl ADR @ -4368 (ADR). The FTIR (Fourier Transform infrared spectroscopy) analysis and SEM (scanning electron microscope) characterization demonstrated that the PLA molecular chain was bonded to the fiber surface and the epoxy-functionalized oligomer played a hinge-like role between the sisal fibers and the PLA matrix, which resulted in improved interfacial adhesion between the fibers and the PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of the ADR oligomer, which in turn reflected the improved interfacial interaction between SF and the PLA matrix. These results were further justified with the calculation of activation energies of glass transition relaxation (∆ E a ) by dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened with the addition of ADR oligomer. The interfacial interaction and structure-properties relationship of the composites are the key points of this study.

  13. Immobilization of iodine in concrete

    International Nuclear Information System (INIS)

    Clark, W.E.; Thompson, C.T.

    1977-01-01

    A method for immobilizing fission product radioactive iodine recovered from irradiated nuclear fuel comprises combining material comprising water, Portland cement and about 3 to 20 wt percent iodine as Ba(IO 3 ) 2 to provide a fluid mixture and allowing the fluid mixture to harden, said Ba(IO 3 ) 2 comprising said radioactive iodine. An article for solid waste disposal comprises concrete prepared by this method. 10 claims, 2 figures

  14. MDCT angiography of the pulmonary arteries: intravascular contrast enhancement does not depend on iodine concentration when injecting equal amounts of iodine at standardized iodine delivery rates

    International Nuclear Information System (INIS)

    Keil, S.; Plumhans, C.; Behrendt, F.F.; Das, M.; Muehlenbruch, G.; Mahnken, A.H.; Guenther, R.W.; Stanzel, S.; Seidensticker, P.; Knackstedt, C.; Wildberger, J.E.

    2008-01-01

    To compare the impact of iodine concentration using two different contrast materials (CM) at standardized iodine delivery rate (IDR) and overall iodine load in 16-multidetector-row-CT-angiography (MDCTA) of the pulmonary arteries of 192 patients with known or suspected pulmonary embolism. One hundred three patients (group A) received 148 ml of a CM containing 300 mg iodine/ml (Ultravist 300 trademark, BayerScheringPharma) at a flow rate of 4.9 ml/s. Eighty-nine patients (group B) received 120 ml of a CM with a concentration of 370 mg iodine/ml (Ultravist370 trademark) at a flow rate of 4.0 ml/s, resulting in a standardized IDR (∝1.5 gI/s) and the same overall amount of iodine (44.4 g). Both CM injections were followed by a saline chaser. Mean density values were determined in the pulmonary trunk, the ascending and the descending aorta, respectively. Applying repeated-measures ANOVA, no statistically significant differences between both MDCTA protocols were found (p=0.5790): the mean density in the pulmonary trunk was 355±116 Hounsfield Units (group A) and 358±115 (group B). The corresponding values for the ascending and descending aorta were 295±79 (group A) and 284±65 (group B) as well as 272±71 and 262±70. In conclusion, the use of standardized IDR and overall iodine load provides comparable intravascular CM density in pulmonary 16-MDCTA for delivering contrast materials with different iodine concentrations. (orig.)

  15. Positron lifetime study of electron-irradiated epoxy resins

    International Nuclear Information System (INIS)

    Suevegh, K.; Vertes, A.; Wojnarovits, L.; Foeldiak, G.; Liszkai, L.; Kajcsos, Zs.

    1990-01-01

    Two bisphenol-A type epoxy resins were irradiated by electron beam and studied afterwards by positron lifetime spectroscopy. An interesting result is that despite of the considerable amount of free-radicals, no inhibition of positronium formation was observed in the two epoxies. Nevertheless, several serious differences were detected between the studied polymers. The results suggest that the radiation-resistant properties of epoxies depend strongly on the amount of the curing agent. (author) 8 refs.; 2 figs

  16. Spectrally selective paint coatings. Preparation and characterization

    Energy Technology Data Exchange (ETDEWEB)

    Crnjak Orel, Z.C.; Klanjsek Gunde, M. [National Institute of Chemistry, Hajdrihova 19, SI-1000 Ljubljana (Slovenia)

    2001-06-01

    Preparation and characterization of spectrally selective paint coating for photothermal solar energy conversion are discussed. The applied methods for preparation of paints with described measurements and calculations of black-pigmented coatings were reviewed. The article represents not only possible future applications but also past and current applications of spectrally selective paint coating which are used all over the world since the 1980s. Spectrally selective paint coatings based on combinations of two types of resins, various types of pigments and three types of silica, were prepared. The influence of pigment type and pigment volume concentration (PVC) was studied by applying the Kubelka-Munk (K-M) theory. The relation between the degrees of dispersion and distribution of pigment particles across the paint layer is discussed in terms of K-M coefficients.

  17. Iodine in drinking water varies by more than 100-fold in Denmark. Importance for iodine content of infant formulas

    DEFF Research Database (Denmark)

    Pedersen, K M; Laurberg, P; Nøhr, S

    1999-01-01

    The iodine intake level of the population is of major importance for the occurrence of thyroid disorders in an area. The aim of the present study was to evaluate the importance of drinking water iodine content for the known regional differences in iodine intake in Denmark and for the iodine content...

  18. Painting Reproductions on Display

    Directory of Open Access Journals (Sweden)

    Joanna Iranowska

    2017-09-01

    Full Text Available Paintings in museums might occasionally be replaced by a photoprint mimicking the original. This article is an investigation of what constitutes a good reproduction of an artwork (oil painting that is meant to be displayed. The article discusses what the usefulness of reproductions depends on, applying the Valuation Studies approach, which means the primary concern is with the practice of valuing itself. In other words, the study focuses on how museum experts evaluate reproduc-tions of oil paintings. The article analyses three cases of displaying digitally prin-ted copies of Edvard Munch's oil paintings between 2013 and 2015 in the Munch Museum and in the National Gallery in Oslo. The study is based on a series of semi-structured interviews with the experts, working at and for the museums, that were involved in producing and exhibiting of the photoprints: curators, con-servators, museum educators, and external manufacturers. The interviews were grouped into five clusters, which I have chosen to call registers of valuing following Frank Heuts and Annemarie Mol (2013. The described valuation practices have to do with delivering experiences to the public, obtaining mimetic resemblance, solving ethical aspects, exhibitions' budget, and last but not least, with the time perspective.

  19. Immobilization of iodine in concrete

    Science.gov (United States)

    Clark, Walter E.; Thompson, Clarence T.

    1977-04-12

    A method for immobilizing fission product radioactive iodine recovered from irradiated nuclear fuel comprises combining material comprising water, Portland cement and about 3-20 wt. % iodine as Ba(IO.sub.3).sub.2 to provide a fluid mixture and allowing the fluid mixture to harden, said Ba(IO.sub.3).sub.2 comprising said radioactive iodine. An article for solid waste disposal comprises concrete prepared by this method. BACKGROUND OF THE INVENTION This invention was made in the course of, or under a contract with the Energy Research and Development Administration. It relates in general to reactor waste solidification and more specifically to the immobilization of fission product radioactive iodine recovered from irradiated nuclear fuel for underground storage.

  20. Experimental design applied optimization of a state in epoxy clay dispersion; Planejamento de experimentos aplicado a otimizacao do estado de dispersao de argilas em epoxi

    Energy Technology Data Exchange (ETDEWEB)

    Paz, Juliana D' Avila; Bertholdi, Jonas; Folgueras, Marilena Valadares; Pezin, Sergio Henrique; Coelho, Luiz Antonio Ferreira, E-mail: julianadpaz@yahoo.com.b [Universidade do Estado de Santa Catarina (UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2010-07-01

    This paper presents some analysis showed that the exfoliation / intercalation of a montmorillonite clay in epoxy resin such as viscosity, X-ray diffraction (XRD), scanning electron microscopy (SEM) and thermogravimetry (TG). Increasing the viscosity of epoxy resin diglycidyl ether bisphenol A with the addition of clay associated with the sonification system at the time of dispersion is a good indication of exfoliation. The X-ray diffraction already cured composite shows a decrease of crystallinity of clay and EDS microanalysis of SEM, non-uniform dispersion of clay in epoxy resin. Thermal analysis TG composite clay / epoxy shows an increase in thermal stability relative to pure epoxy. (author)

  1. Zinc, Paint loss and Harmony in blue

    DEFF Research Database (Denmark)

    Vila, Anna; Krarup Andersen, Cecil; Baadsgaard, Elizabeth

    2016-01-01

    P.S. Krøyer’s late and most popular paintings have proven very difficult to preserve, and as zinc white has been known to cause structural problems in paintings, the authors investigate if the damage seen in the late paintings can be related to the use of this relatively new pigment. Eight painti...

  2. Risk of suboptimal iodine intake in pregnant Norwegian women.

    Science.gov (United States)

    Brantsæter, Anne Lise; Abel, Marianne Hope; Haugen, Margaretha; Meltzer, Helle Margrete

    2013-02-06

    Pregnant women and infants are exceptionally vulnerable to iodine deficiency. The aims of the present study were to estimate iodine intake, to investigate sources of iodine, to identify predictors of low or suboptimal iodine intake (defined as intakes below 100 μg/day and 150 μg/day) in a large population of pregnant Norwegian women and to evaluate iodine status in a sub-population. Iodine intake was calculated based on a validated Food Frequency Questionnaire in the Norwegian Mother and Child Cohort. The median iodine intake was 141 μg/day from food and 166 μg/day from food and supplements. Use of iodine-containing supplements was reported by 31.6%. The main source of iodine from food was dairy products, contributing 67% and 43% in non-supplement and iodine-supplement users, respectively. Of 61,904 women, 16.1% had iodine intake below 100 μg/day, 42.0% had iodine intake below 150 μg/day and only 21.7% reached the WHO/UNICEF/ICCIDD recommendation of 250 μg/day. Dietary behaviors associated with increased risk of low and suboptimal iodine intake were: no use of iodine-containing supplements and low intake of milk/yogurt, seafood and eggs. The median urinary iodine concentration measured in 119 participants (69 μg/L) confirmed insufficient iodine intake. Public health strategies are needed to improve and secure the iodine status of pregnant women in Norway.

  3. Weight, iodine content and iodine uptake of the thyroid gland of normal Japanese

    International Nuclear Information System (INIS)

    Yoshizawa, Yasuo; Kusama, Tomoko

    1976-01-01

    Various questions arise in the application of ICRP ''Standard Man'' values to Japanese. One of the questions is that ''Standard Man'' values of the thyroid are different from normal Japanese values. A systematic survey of past reports was carried out with a view to search for normal Japanese values of the thyroid. The subjects of search were weight, iodine content and iodine uptake rate (f sub(w)) of the thyroid. These are important factors in the estimation of the radiation dose of the thyroid caused by internal contamination of radioiodine, and are foreseen to have the difference between Japanese and ''Standard Man''. The result of study suggested that the weight of the thyroid of normal Japanese is about 19 g for adult male and about 17 g for adult female, and that the iodine content is 12-22 mg and iodine uptake rate (f sub(w)) is about 0.2. (auth.)

  4. X-ray Pump–Probe Investigation of Charge and Dissociation Dynamics in Methyl Iodine Molecule

    Directory of Open Access Journals (Sweden)

    Li Fang

    2017-05-01

    Full Text Available Molecular dynamics is of fundamental interest in natural science research. The capability of investigating molecular dynamics is one of the various motivations for ultrafast optics. We present our investigation of photoionization and nuclear dynamics in methyl iodine (CH3I molecule with an X-ray pump X-ray probe scheme. The pump–probe experiment was realized with a two-mirror X-ray split and delay apparatus. Time-of-flight mass spectra at various pump–probe delay times were recorded to obtain the time profile for the creation of high charge states via sequential ionization and for molecular dissociation. We observed high charge states of atomic iodine up to 29+, and visualized the evolution of creating these high atomic ion charge states, including their population suppression and enhancement as the arrival time of the second X-ray pulse was varied. We also show the evolution of the kinetics of the high charge states upon the timing of their creation during the ionization-dissociation coupled dynamics. We demonstrate the implementation of X-ray pump–probe methodology for investigating X-ray induced molecular dynamics with femtosecond temporal resolution. The results indicate the footprints of ionization that lead to high charge states, probing the long-range potential curves of the high charge states.

  5. Bio-Based Aromatic Epoxy Monomers for Thermoset Materials

    Directory of Open Access Journals (Sweden)

    Feifei Ng

    2017-01-01

    Full Text Available The synthesis of polymers from renewable resources is a burning issue that is actively investigated. Polyepoxide networks constitute a major class of thermosetting polymers and are extensively used as coatings, electronic materials, adhesives. Owing to their outstanding mechanical and electrical properties, chemical resistance, adhesion, and minimal shrinkage after curing, they are used in structural applications as well. Most of these thermosets are industrially manufactured from bisphenol A (BPA, a substance that was initially synthesized as a chemical estrogen. The awareness on BPA toxicity combined with the limited availability and volatile cost of fossil resources and the non-recyclability of thermosets implies necessary changes in the field of epoxy networks. Thus, substitution of BPA has witnessed an increasing number of studies both from the academic and industrial sides. This review proposes to give an overview of the reported aromatic multifunctional epoxide building blocks synthesized from biomass or from molecules that could be obtained from transformed biomass. After a reminder of the main glycidylation routes and mechanisms and the recent knowledge on BPA toxicity and legal issues, this review will provide a brief description of the main natural sources of aromatic molecules. The different epoxy prepolymers will then be organized from simple, mono-aromatic di-epoxy, to mono-aromatic poly-epoxy, to di-aromatic di-epoxy compounds, and finally to derivatives possessing numerous aromatic rings and epoxy groups.

  6. Effectiveness and risks of stable iodine prophylaxis

    International Nuclear Information System (INIS)

    Waight, P.J.

    1995-01-01

    The factors upon which the efficacy of stable iodine prophylaxis depends are reviewed, with particular reference to the dose of stable iodine, the timing of the dose, the influence of dietary iodine and the impact of the other prospective actions. The risks of stable iodine ingestion are estimated, and their application to the principle of Justification in outlined. (Author)

  7. Thermal conductivity and Kapitza resistance of cyanate ester epoxy mix and tri-functional epoxy electrical insulations at superfluid helium temperature

    CERN Document Server

    Pietrowicz, S; Jones, S; Canfer, S; Baudouy, B

    2012-01-01

    In the framework of the European Union FP7 project EuCARD, two composite insulation systems made of cyanate ester epoxy mix and tri-functional epoxy (TGPAP-DETDA) with S-glass fiber have been thermally tested as possible candidates to be the electrical insulation of 13 T Nb$_{3}$Sn high field magnets under development for this program. Since it is expected to be operated in pressurized superfluid helium at 1.9 K and 1 atm, the thermal conductivity and the Kapitza resistance are the most important input parameters for the thermal design of this type of magnet and have been determined in this study. For determining these thermal properties, three sheets of each material with different thicknesses varying from 245 μm to 598 μm have been tested in steady-state condition in the temperature range of 1.6 K - 2.0 K. The thermal conductivity for the tri-functional epoxy (TGPAP-DETDA) epoxy resin insulation is found to be k=[(34.2±5.5).T-(16.4±8.2)]×10-3 Wm-1K-1 and for the cyanate ester epoxy k=[(26.8±4.8).T- (9...

  8. Aged anthropogenic iodine in a boreal peat bog

    International Nuclear Information System (INIS)

    Maillant, S.; Sheppard, M.I.; Denys, S.; Leclerc Cessac, E.

    2004-01-01

    Iodine-129 is a radionuclide of major concern in the international safety assessments for deep geological storage and disposal of nuclear waste because it migrates quickly through the geosphere to the biosphere and then from the soil to humans through the food-chain. However, in organic soils the 129 I may be immobilized over a long time period, and so these soils represent a potential accumulation point in the biosphere. Effects of long residence times of iodine in soils are scarce. The present paper gives some insight on the aging of stable iodine, under natural conditions. Stable iodine was introduced as KI in 1987 at the base of a small natural sphagnum bog to simulate arrival of iodine via a groundwater discharge from the geosphere. Previous data revealed the spread of the iodine outwards spatially from the basal spike and also recorded its rise towards the bog surface. Fifteen years later, the groundwater, the soil and the vegetation have been sampled and analyzed for iodine. The results we will present give insight on the mobility of 'aged' iodine with time, the retention properties of the peat, and provide iodine transfer factors for native boreal plant species. The data show iodine: - continues to slowly spread from the spike after 15 years, - is more strongly retained on the solid phase at the surface than at depth, - the chemical structure of the peat may influence the retention of iodine as shown by NMR analysis, - iodine retention has become greater with time, and - herbaceous species are the greatest accumulators. This study demonstrates bogs present good sinks for iodine and limit the transfer of iodine to some of the 'wildlife' food-chains. (author)

  9. Paint Scaler. Innovative Technology Summary Report

    International Nuclear Information System (INIS)

    None

    2000-01-01

    The Paint Scaler can collect paint samples quickly and efficiently for lab analysis. The Rotary Hammer Drill is a 24-V battery operated, 3/4-in. rotary hammer drill. When used with an optional chipping adapter, the Bosch Rotary Hammer Drill can be used to perform chipping and chiseling tasks such as paint removal from either concrete or metal surfaces. It is ultra-compact, lightweight with an ergonomic balanced grip. The battery operation gives the operator more flexibility during sampling activities

  10. Iodine Contents in Baby Food Consumed in Japan

    Directory of Open Access Journals (Sweden)

    Yoshida M.

    2013-04-01

    Full Text Available To evaluate iodine intake in Japanese infants, iodine contents were determined in both commercial and homemade baby food samples consumed in Japan. Fifty-three samples of commercial bottled or retort baby food and 25 samples of homemade baby food for one day were collected and their iodine contents were determined by inductively coupled plasma mass spectrometry after an extraction with 0.5% tetramethylammonium hydroxide. Among the commercial baby food samples, 35 samples showed low iodine values ( 1000 ng/g wet weight. Significantly higher iodine values were observed in 15 samples composed of dishes cooked using kombu (a kind of kelp than other samples. Among the homemade baby food samples, 12 samples brought very low iodine intake (< 1- 24 μg/d, while 5 samples brought very high iodine intake (283-978 μg/d. These results indicate that intermittent high iodine baby food including dishes cooked using kombu contributes to sufficient iodine intake in Japanese infants.

  11. Magnetism in graphene oxide induced by epoxy groups

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dongwook, E-mail: dongwookleedl324@gmail.com [Cavendish Laboratory, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Division of Physics and Applied Physics, Nanyang Technological University, Singapore 637371 (Singapore); Seo, Jiwon, E-mail: jiwonseo@yonsei.ac.kr [Department of Physics and IPAP, Yonsei University, Seoul 120-749 (Korea, Republic of); School of Advanced Materials Science and Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Zhu, Xi; Su, Haibin [Division of Materials Science, School of Materials Science and Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Cole, Jacqueline M. [Cavendish Laboratory, University of Cambridge, Cambridge CB3 0HE (United Kingdom); Argonne National Laboratory, 9700S Cass Avenue, Argonne, Illinois 60439 (United States)

    2015-04-27

    We have engineered magnetism in graphene oxide. Our approach transforms graphene into a magnetic insulator while maintaining graphene's structure. Fourier transform infrared spectroscopy spectra reveal that graphene oxide has various chemical groups (including epoxy, ketone, hydroxyl, and C-O groups) on its surface. Destroying the epoxy group with heat treatment or chemical treatment diminishes magnetism in the material. Local density approximation calculation results well reproduce the magnetic moments obtained from experiments, and these results indicate that the unpaired spin induced by the presence of epoxy groups is the origin of the magnetism. The calculation results also explain the magnetic properties, which are generated by the interaction between separated magnetic regions and domains. Our results demonstrate tunable magnetism in graphene oxide based on controlling the epoxy group with heat or chemical treatment.

  12. Experiments on The Retention of The Fission Product Iodine in Nuclear Reactor Accidents

    International Nuclear Information System (INIS)

    Bruchertseifer, H.; Cripps, R.; Guentay, S.; Jaeckel, B.

    2004-01-01

    The paper reports PSI participation in the ICHEMM Project (Iodine Chemistry and Mitigation Mechanisms) of the EU 5th Framework Programme, which has the objective of identifying new possible mitigation processes, or accident management measures, favouring the conversion of volatile iodine species, especially organic iodine released during a severe accident at a Nuclear Power Plant (NPP), into nonvolatile forms. Significant effort has been expended, firstly to develop analytical methods for determining concentrations of the common iodine species (iodide, iodate, molecular iodine and methyl iodide), and secondly to provide missing and important information on decomposition phenomena and involved reactions. Experiments have been conducted at PSI to obtain data on thermal (hydrolysis) and radiolytic decomposition of CH 3 I in aqueous solution under conditions as close as possible to those in an anticipated accident. Radioactive-labelled methyl iodide was used to monitor and quantify the decomposition and to determine the overall mass balance. Results have shown that CH 3 I hydrolysis at 90 o C will dominate over radiolysis at the dose rates (max. 0.4 Gy.s -1 ) employed in the experiments. Much increased decomposition rates of CH 3 I have been achieved with chemical reagents (additives), such as sodium thiosulphate or ammonium sulphide. After completion of the ICHEMM Project, further advances have been made from experiments carried out on additives (especially in combination with Aliquat 336) in terms of a fast and complete retention of iodine. The data from these experiments are of direct relevance to severe accident management for both PWR and BWR systems. The impact of the results on possible strategies for management of radioactive waste has also been investigated. (author)

  13. Experiments on The Retention of The Fission Product Iodine in Nuclear Reactor Accidents

    Energy Technology Data Exchange (ETDEWEB)

    Bruchertseifer, H.; Cripps, R.; Guentay, S.; Jaeckel, B

    2004-03-01

    The paper reports PSI participation in the ICHEMM Project (Iodine Chemistry and Mitigation Mechanisms) of the EU 5th Framework Programme, which has the objective of identifying new possible mitigation processes, or accident management measures, favouring the conversion of volatile iodine species, especially organic iodine released during a severe accident at a Nuclear Power Plant (NPP), into nonvolatile forms. Significant effort has been expended, firstly to develop analytical methods for determining concentrations of the common iodine species (iodide, iodate, molecular iodine and methyl iodide), and secondly to provide missing and important information on decomposition phenomena and involved reactions. Experiments have been conducted at PSI to obtain data on thermal (hydrolysis) and radiolytic decomposition of CH{sub 3}I in aqueous solution under conditions as close as possible to those in an anticipated accident. Radioactive-labelled methyl iodide was used to monitor and quantify the decomposition and to determine the overall mass balance. Results have shown that CH{sub 3}I hydrolysis at 90{sup o}C will dominate over radiolysis at the dose rates (max. 0.4 Gy.s{sup -1}) employed in the experiments. Much increased decomposition rates of CH{sub 3}I have been achieved with chemical reagents (additives), such as sodium thiosulphate or ammonium sulphide. After completion of the ICHEMM Project, further advances have been made from experiments carried out on additives (especially in combination with Aliquat 336) in terms of a fast and complete retention of iodine. The data from these experiments are of direct relevance to severe accident management for both PWR and BWR systems. The impact of the results on possible strategies for management of radioactive waste has also been investigated. (author)

  14. Examination of lead concentrations in new decorative enamel paints in four countries with different histories of activity in lead paint regulation

    Energy Technology Data Exchange (ETDEWEB)

    Clark, C. Scott, E-mail: clarkcs@ucmail.uc.edu [Department of Environmental Health, University of Cincinnati (United States); International POPS Elimination Network (IPEN), San Francisco (United States); Kumar, Abhay; Mohapatra, Piyush; Rajankar, Prashant [Toxics Link, New Delhi (India); Nycz, Zuleica [APROMAC Environmental Protection Association and Toxisphera Environmental Health Association, Curitiba, Parana (Brazil); Hambartsumyan, Amalia [Greenwomen, Almaty (Kazakhstan); Astanina, Lydia [Khazer Ecological and Cultural Non-Governmental Organization, Yerevan (Armenia); Roda, Sandy; Lind, Caroline; Menrath, William; Peng, Hongying [Department of Environmental Health, University of Cincinnati (United States)

    2014-07-15

    Paints with high lead concentrations (ppm) continue to be sold around the world in many developing countries and those with economies in transition representing a major preventable environmental health hazard that is being increased as the economies expand and paint consumption is increasing. Prior lead paint testing had been performed in Brazil and India and these countries were selected to examine the impact of a new regulatory limit in Brazil and the impact of efforts of non-governmental organizations and others to stop the use of lead compounds in manufacturing paints. Armenia and Kazakhstan, in Central Asia, were selected because no information on lead concentration in those regions was available, no regulatory activities were evident and non-governmental organizations in the IPEN network were available to participate. Another objective of this research was to evaluate the lead loading (µg/cm{sup 2}) limit determined by X-Ray Fluorescence (XRF) for areas on toys that are too small to obtain a sample of sufficient size for laboratory analysis. The lead concentrations in more than three-fourths of the paints from Armenia and Kazakhstan exceeded 90 ppm, the limit in the United States, and 600 ppm, the limit in Brazil. The percentages were about one-half as high in Brazil and India. The average concentration in paints purchased in Armenia, 25,000 ppm, is among the highest that has been previously reported, that in Kazakhstan, 15,700 ppm, and India, 16,600, about median. The average concentration in Brazil, 5600 ppm, is among the lowest observed. Paints in Brazil that contained an average of 36,000 ppm before the regulatory limit became effective were below detection (<9 ppm) in samples collected in the current study. The lack of any apparent public monitoring of paint lead content as part of regulatory enforcement makes it difficult to determine whether the regulation was a major factor contributing to the decline in lead use in these paints. Using data from the

  15. An assessment of the iodine status and the correlation between iodine nutrition and thyroid function during pregnancy in an iodine sufficient area.

    Science.gov (United States)

    Amouzegar, A; Khazan, M; Hedayati, M; Azizi, F

    2014-03-01

    Iodine as a micronutrient is mandatory for thyroid hormone production and inadequate iodine intakes during pregnancy may result in varying degrees of hypothyroidism affecting pregnancy outcomes adversely. The aim of this study was to evaluate nutritional status and its effects on thyroid function in pregnant women during all trimesters of pregnancy. In this cohort study, we assessed a total of 203 pregnant women in the first trimester of pregnancy and followed them in the second and third trimesters. They were divided into two groups, group I with urinary iodine excretion (UIE) pregnancy, respectively; UIEpregnancy, respectively. The median (range) of TSH was 1.7 (0.9-2.7) mIU/l, 1.9(1.2-2.7) mIU/l and 1.8 (1.1-2.8) mIU/l in the three trimesters of pregnancy, respectively. There was no correlation between UIE, TSH, TT4, FT4I, T3 and TPOAb in the first and second trimesters, but there was a weak correlation between UIE, TSH, T3 and TgAb in the third trimester. In our cohort of pregnant women the iodine intakes were sufficient, and no correlation between urinary iodine concentration and thyroid function tests was found.

  16. Sanding dust from nanoparticle-containing paints: Physical characterisation

    International Nuclear Information System (INIS)

    Koponen, I K; Jensen, K A; Schneider, T

    2009-01-01

    Increasing use of nanoparticles in different industrial applications has raised a new potential health risk to the workers as well as to the consumers. This study investigates the particle size distributions of sanding dust released from paints produced with and without engineered nanoparticles. Dust emissions from sanding painted plates were found to consist of five size modes; three modes under 1 μm and two modes around 1 and 2 μm. We observed that the sander was the only source of particles smaller than 50 nm and they dominated the number concentration spectra. Mass and surface area spectra were dominated by the 1 and 2 μm modes. Addition of nanoparticles caused only minor changes in the geometric mean diameters of the particle modes generated during sanding of two paints doped with 17 nm TiO2 and 95 nm Carbon Black nanoparticles as compared to the size modes generated during sanding a conventional reference paint. However, the number concentrations in the different size modes varied considerably in between the two NP-doped paints and the reference paint. Therefore, from a physical point of view, there may be a difference in the exposure risk during sanding surfaces covered with nanoparticle-based paints as compared to sanding conventional paints.

  17. Electron-collision cross sections for iodine

    International Nuclear Information System (INIS)

    Zatsarinny, O.; Bartschat, K.; Garcia, G.; Blanco, F.; Hargreaves, L.R.; Jones, D.B.; Murrie, R.; Brunton, J.R.; Brunger, M.J.; Hoshino, M.; Buckman, S.J.

    2011-01-01

    We present results from a joint experimental and theoretical study of elastic electron scattering from atomic iodine. The experimental results were obtained by subtracting known cross sections from the measured data obtained with a pyrolyzed mixed beam containing a variety of atomic and molecular species. The calculations were performed using both a fully relativistic Dirac B-spline R-matrix (close-coupling) method and an optical model potential approach. Given the difficulty of the problem, the agreement between the two sets of theoretical predictions and the experimental data for the angle-differential and the angle-integrated elastic cross sections at 40 eV and 50 eV is satisfactory.

  18. The Impact of Carrot Enriched in Iodine through Soil Fertilization on Iodine Concentration and Selected Biochemical Parameters in Wistar Rats

    Science.gov (United States)

    Piątkowska, Ewa; Kopeć, Aneta; Bieżanowska-Kopeć, Renata; Pysz, Mirosław; Kapusta-Duch, Joanna; Koronowicz, Aneta Agnieszka; Smoleń, Sylwester; Skoczylas, Łukasz; Ledwożyw-Smoleń, Iwona; Rakoczy, Roksana; Maślak, Edyta

    2016-01-01

    Iodine is one of the trace elements which are essential for mammalian life. The major objective of iodine biofortification of plants is to obtain food rich in this trace element, which may increase its consumption by various populations. Additionally, it may reduce the risk of iodine deficiency diseases. In this research for the first time we have assessed the bioavailability of iodine from raw or cooked carrot biofortified with this trace element on iodine concentration in selected tissues and various biochemical parameters as well as mRNA expression of some genes involved in iodine metabolism in Wistar rats. Statistically, a significantly higher iodine level was determined in urine, faeces and selected tissues of rats fed a diet containing biofortified raw carrot as compared to a diet without iodine and a diet containing control cooked carrot. Biofortified raw carrot significantly increased triiodothyronine concentration as compared to animals from other experimental groups. The highest thyroid stimulating hormone level was determined in rats fed control cooked carrots. mRNA expression of selected genes was affected by different dietary treatment in rats’ hearts. Biofortified raw and cooked carrot could be taken into account as a potential source of iodine in daily diets to prevent iodine deficiency in various populations. PMID:27043135

  19. Iodine/steel reactions under severe accident conditions in LWR's

    International Nuclear Information System (INIS)

    Funke, F.; Greger, G-U.; Hellman, S.; Bleier, A.; Morell, W.

    1994-01-01

    Due to large surface areas, the reaction of volatile, molecular iodine (I 2 ) with steel surfaces in the containment may play an important role in predicting the source term to the environment. Both wall retention of iodine and conversion of volatile into non-volatile iodine compounds at steel surfaces have to be considered. Two types of laboratory experiments were carried out at Siemens/KWU in order to investigate the reaction of I 2 at steel surfaces representative for German power plants. 1) For steel coupons submerged in an I 2 solution at T = 50 deg C, 90 deg C or 140 deg C the reaction rate of the I 2 /I - conversion was determined. No iodine loading was observed on the steel in the aqueous phase tests. I 2 reacts with the steel components (Fe, Cr or Ni) to form metal iodides on the surface which are all immediately dissolved in water under dissociation into the metal and the iodide ions. From these experiments, the I 2 /I - conversion rate constants over the temperature range 50 deg C - 140 deg C as well as the activation energy were determined. The measured data are suitable to be included in severe accident iodine codes such as IMPAIR. 2) Steel tubes were exposed to a steam/I 2 flow under dry air at T=120 deg C and steam-condensing conditions at T= 120 deg C and 160 deg C. In dry air I 2 was retained on the steel surface and a deposition rate constant was measured. Under steam-condensing conditions there is an effective conversion of volatile I 2 to non-volatile I - which is subsequently washed off from the steel surface. The I 2 /I - conversion rate constants suitable for modelling this process were determined. No temperature dependency was found in the range 120 deg C - 160 deg C. (author). 4 refs., 2 tabs., 7 figs

  20. Criteria for safe working with iodine-125

    International Nuclear Information System (INIS)

    Linsley, G.S.

    1977-01-01

    Radio-immunoassay and other saturation assay tests involving the use of iodine-125 are finding wide application for the determination of hormone concentrations in biological fluids. In such tests, iodinations involving concentrations of a milli-curie per micro-litre are common. Iodine-125 presents a problem from the monitoring standpoint because of its low energy photon emission (27 and 35 keV). Iodine is preferentially taken up by the thyroid gland and work involving moderate amounts of radio-iodine may give rise to a significant hazard in an accident situation. The general precautions which should be taken in work with unsealed radioactive substances are briefly summarized, working limits for iodine-125 are identified, and methods of personal protection and monitoring in an emergency situation described. (author)