Energy Technology Data Exchange (ETDEWEB)

The Active Magnetospheric Particle Tracer Explorers (AMPTE) program provided important information on the behavior of clouds of plasma artificially injected into the solar wind and the earth's magnetosphere. Now that the releases are over, data from the satellites are being analyzed to investigate the processes by which the ambient solar wind mass, momentum, and energy are transferred to the magnetosphere. Work in progress at APL indicates that the solar wind is much more inhomogeneous than previously believed, that the solar wind constantly buffets the magnetosphere, and that ground observers may remotely sense these interactions as geomagnetic pulsations. 8 refs.

Energy Technology Data Exchange (ETDEWEB)

In this work, the pulse plasma nitriding process of pure iron is modelled using a kinetic model derived from the Fick's laws. This approach based on the error function model allows to simulate the growth kinetics of a biphase configuration consisting of {gamma}'-Fe{sub 4}N{sub 1-x} and {epsilon}-Fe{sub 2-3}N iron nitrides under specified conditions. By coupling the kinetics data about the diffusivities of nitrogen in {alpha}-Fe, {gamma}' and {epsilon} phases to the thermodynamic description of the Fe-N phase diagram, it is possible to evaluate the kinetic constant at each growing phase interface, the thickness of nitrided layer, and predict the nitrogen concentration profiles. The comparison between the experimental and theoretical results shows the reliability of the simulation results.

Science.gov (United States)

Nov 14, 2009 ... Ring Current electrons from the Fok Ring Current Model are computed using plasma and magnetic field values from the SWMF magnetosphere ...

Science.gov (United States)

Nov 14, 2009 ... Ring Current electrons from the Fok Ring Current Model are computed using plasma and magnetic field values from the SWMF magnetosphere ...

Energy Technology Data Exchange (ETDEWEB)

Linear properties of ion temperature gradient (ITG) modes in helical systems are studied. The real frequency, growth rate, and eigenfunction are obtained for both stable and unstable cases by solving a kinetic integral equation with proper analytic continuation performed in the complex frequency plane. Based on the model magnetic configuration for toroidal helical systems like the Large Helical Device (LHD), dependences of the ITG mode properties on various plasma equilibrium parameters are investigated. Particularly, relative effects of {nabla}B-curvature drifts driven by the toroidicity and by the helical ripples are examined in order to compare the ITG modes in helical systems with those in tokamaks. (author)

CERN Document Server

Using the recently developed effective field theory of inflation, we argue that the size and the shape of the non-Gaussianities generated by single-field inflation are generically well described by two parameters: f_NL^equil, which characterizes the size of the signal that is peaked on equilateral configurations, and f_NL^orthog, which instead characterizes the size of the signal which is peaked both on equilateral configurations and flat-triangle configurations (with opposite signs). The shape of non-Gaussianities associated with f_NL^orthog is orthogonal to the one associated to f_NL^equil, and former analysis have been mostly blind to it. We perform the optimal analysis of the WMAP 5-year data for both of these parameters. We find no evidence of non-Gaussianity, and we have the following constraints: -125 0.011 at 95% CL. or alternatively to be so small that the higher-derivative kinetic term ...

CERN Document Server

Several observational studies suggest that solar wind dynamic pressure fluctuations can drive magnetospheric ultra-low frequency (ULF) waves on the dayside. To investigate this causal relationship, we present results from Lyon-Fedder-Mobarry (LFM) global, three-dimensional magnetohydrodynamic (MHD) simulations of the solar wind-magnetosphere interaction. These simulations are driven with synthetic solar wind input conditions, where idealized ULF dynamic pressure fluctuations are embedded in the upstream solar wind. In three of the simulations, a monochromatic, sinusoidal ULF oscillation is introduced into the solar wind dynamic pressure time series. In the fourth simulation, a continuum of ULF fluctuations over the 0-50 mHz frequency band is introduced into the solar wind dynamic pressure time series. In this numerical experiment, the idealized solar wind input conditions allow us to study only the effect of a fluctuating solar wind dynamic ...

Energy Technology Data Exchange (ETDEWEB)

In this study we extend the analysis of magnetopause crossings observed with Magnetospheric Plasma Analyzer measurements to examine a much larger statistical data set. This study examines 39 maiznetosheath/LLBL intervals from 79 spacecraft-months of observations: these observations were taken from a survey of data from the start of each spacecraft mission and extending through March 1993. In contrast to the previous findings, we find no evidence for a significant dawn/dusk asymmetry in geosynchronous magnetopause crossings.

Energy Technology Data Exchange (ETDEWEB)

The role played by calcium sulfite in the flue gas desulfurization of lime/limestone scrubbers makes it desirable to work out its thermodynamic properties. A thermogravimetric apparatus was used to study the equilibria between calcium sulfite hemihydrate and calcium sulfite anhydrite under different conditions. Efforts were made to analyze the difficulties encountered in the dynamic approach to equilibration after calcium sulfate dihydrate failed in calibration of the apparatus. Finally, the kinetics and thermodynamics for the dissociation of calcium sulfite hemihydrate were examined. The confirmation of Engel-Brewer's correlation between the electronic configuration and crystal structure in metallic systems has long been pursued in this group by studying the Lewis-acid-base interactions. Tantalum-iridium alloys of different compositions were brought into equilibrium with various steam/hydrogen mixtures in the same thermogravimetric ...

Energy Technology Data Exchange (ETDEWEB)

This series of measurements with a mixed Pu-U nitrate solution (280 g Pu/liter, 180 g U/liter) in a 35.54-cm-diam cylindrical tank provides a wide variety of experimental data for subcritical configurations that can be used to verify calculational methods and nuclear data. The Pu contained 7.85 wt% {sup 240}Pu and the uranium was natural uranium. The measurements performed were: inverse count rate, prompt neutron decay constants, inverse kinetics, and frequency analysis by the {sup 252}Cf source driven method. These data are presented in sufficient detail that the results of the experiments can be calculated directly. For purposes of extrapolating to the delayed critical height the ratio of spectral densities was linear with height and thus provided the best estimate of critical height.

International Nuclear Information System (INIS)

We have studied the features of formation and the possible stationary structures of a self-consistent magnetic field in a relativistic collisionless plasma, which are characteristic of a simple geometry of the Weibel instability that is well known in the nonrelativistic case. The universal condition is established, the growth rate is determined, and the criteria of saturation of the Weibel instability are analyzed for a broad class of anisotropic particle distribution functions (for definiteness, in application to an electron-positron plasma). A nonlinear equation of the Grad-Shafranov type describing the potential current structures is derived and its solutions are analytically studied. Special attention is paid to spatially harmonic, nonlinear current configurations with parameters determined by the properties of the initial homogeneous plasma subject to the Weibel instability. It is demonstrated that the magnetic field energy density in the obtained solutions ...

CERN Document Server

Two-dimensional simulations of the coarsening process of the isotropic/smectic-A phase transition are presented using a high-order Landau-de Gennes type free energy model. Defect annihilation laws for smectic disclinations, elementary dislocations, and total dislocation content are determined. The computed evolution of the orientational correlation length and disclination density is found to be in agreement with previous experimental observations showing that disclination interactions dominate the coarsening process. The mechanism of smectic disclination movement, limited by the absorption and emission of elementary dislocations, is found to be facilitated by curvature walls connecting interacting disclinations. At intermediate times in the coarsening process, split-core dislocation formation and interactions displaying an effective disclination quadrupole configuration are observed. This work provides the framework for further understanding of the formation and ...

Energy Technology Data Exchange (ETDEWEB)

This paper discusses how to overcome failures and pitfalls in software configuration management. (LSP)

Science.gov (United States)

After each archwire was ligated into a bracket with a 0.010-in stainless steel wire, both stainless steel and beta-titanium archwires (0.017- x 0.025-in) were slid through commercially pure titanium brackets (0.018-in slot size) at 34 degrees C in both the dry and wet conditions. As controls, stainless steel archwire versus stainless steel bracket couples were used with comparable dimensions. The drawing forces were measured at 5 angulations (0 degrees, 3 degrees, 7 degrees, 9 degrees, and 11 degrees ) for 5 normal forces (nominally 0.2, 0.4, 0.6, 0.8, and 1.0 kg). Regression lines were determined for each frictional couple (P <.05). In the passive configuration, the kinetic frictional coefficients of control and test couples in the dry condition were comparable to previously reported values at 0.11 +/- 0.01 for stainless steel versus stainless steel, 0.12 +/- 0.00 for stainless steel versus titanium, and 0.26 +/- 0.02 for beta-titanium ...

Energy Technology Data Exchange (ETDEWEB)

The subcriticality of two interacting solution tanks was determined using /sup 252/Cf-source-driven neutron noise analysis methods. These experiments were the first test of this method for an interacting system with materials (in this case, uranyl nitrate) typical of nuclear materials in processing plants. The experiments were performed to test the conclusions from previous interaction experiments with uranium metal discs for a fissile system with moderation, and to provide data to test theoretical models for coupled systems. The uranium metal experiments showed that the subcritical neutron multiplication factor, k/sub eff/, could be determined using point kinetics without any correction for spatial effects from measurements with the source and detectors located adjacent to the same cylinder, whereas for source-detector configurations with either the source and/or detectors adjacent to different cylinders, a model which incorporates the ...

Energy Technology Data Exchange (ETDEWEB)

Essential to today's modern refineries and the gasoline production process are fluidized catalytic cracking units. By using a computational fluid dynamics (CFD) code developed at Argonne National Laboratory to simulate the riser, parametric and sensitivity studies were performed to determine the effect of catalyst inlet conditions on the riser hydrodynamics and on the product yields. Simulations were created on the basis of a general riser configuration and operating conditions. The results of this work are indications of riser operating conditions that will maximize specific product yields. The CFD code is a three-dimensional, multiphase, turbulent, reacting flow code with phenomenological models for particle-solid interactions, droplet evaporation, and chemical kinetics. The code has been validated against pressure, particle loading, and product yield measurements. After validation of the code, parametric studies were performed on ...

Energy Technology Data Exchange (ETDEWEB)

Pre-stacking depth migration treatment is studied for the estimation of the fold configuration from seismic survey cross sections. The estimation of a velocity structure is necessary for the execution of such treatment, and the utilization of structural-geological knowledge is required for its interpretation. The concept of balanced cross section in relation to the fault-bend fold constructs a stratum structure model under conditions that the deformation during fold and fault formation is a planar strain, that there is no change in volume due to deformation, and that a fold is a parallel fold. In addition to the above geometric and kinetic approach, there is another fold formation process simulation model using a Newtonian fluid for study from the viewpoint of dynamics. This simulation stands on the presumption that the boundary contains a ramp that had been in presence before fold formation and that an incompressible viscous matter is mounted ...

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

Science.gov (United States)

The use of ceramics as energy absorbents has been studied by many researchers and some improvements in the ballistic performance of ceramic tiles have been made by coating them with different classes of materials (e.g. E-glass/epoxy, carbon-fiber/epoxy, etc.). Using ceramics for energy absorbing applications leads to a significant weight reduction of the system. Therefore, any modification to the ceramic configuration in the system which leads to more energy absorption with the same or less areal density is significant. On the other hand, polyurea has been proved to be an excellent energy dissipating agent in many applications. Inspired by this, we are studying the effect of coating ceramics with polyurea and other materials, on the energy absorption and ballistic performance of the resulting ceramic-based composites. In this study, we investigate the effect of polyurea on ballistic efficiency of ceramic tiles. To this end, we have performed a set of penetration ...

Energy Technology Data Exchange (ETDEWEB)

This thesis is concerned with the crystallisation behaviour of polymers near to a free surface or a buried interface. The properties of polymers are expected to differ significantly near to an interface (either with air or another polymer), due to the contributions of (a) chain configurations induced at the interface, and (b) different mobilities between interfacial regions and the bulk of the sample. For a semi-crystalline polymer, properties such as the degree of crystallinity and the crystallisation kinetics may be enhanced near to a free surface. Grazing incidence x--ray diffraction (GIXD) is used to investigate such effects in poly(ethylene terphthalate) (PET), showing that a lower crystallisation temperature is obtained at the surface, and the crystallisation kinetics are faster at the surface for all temperatures. It is proposed that in thin films of PET, this surface-induced ordering provides nucleation sites for ...

CERN Document Server

The interaction of accretion disks with the magnetospheres of young stars can produce X-winds and funnel flows. With the assumption of axial symmetry and steady state flow, the problem can be formulated in terms of quantities that are conserved along streamlines, such as the Bernoulli integral (BI), plus a partial differential equation (PDE), called the Grad-Shafranov equation (GSE), that governs the distribution of streamlines in the meridional plane. The GSE plus BI yields a PDE of mixed type, elliptic before critical surfaces where the flow speed equals certain characteristic wave speeds are crossed and hyperbolic afterward. The computational difficulties are exacerbated by the locations of the critical surfaces not being known in advance. To overcome these obstacles, we consider a variational principle by which the GSE can be attacked by extremizing an action integral, with all other conserved quantities of the problem explicitly included as part of the overall ...

Science.gov (United States)

The transport of magnetospheric particles in the outer cusp region is examined by means of three-dimensional single particle codes. It is shown that, at high altitudes, particles can experience nonadiabatic motions leading to significant magnetic moment changes. It is demonstrated that this nonadiabatic behavior can be interpreted, at least partly, by the action of an impulsive centrifugal force perturbing the particle gyromotion. Systematic trajectory calculations reveal that plasma sheet ions which ExB convert toward the magnetopause from low L-shells in the dayside sector are subjected to such nonadiabatic motions. As a result of magnetic moment damping, a number of them are injected into the loss cone and subsequently precipitate near the cusp equatorward edge.

International Nuclear Information System (INIS)

Dust particles in a plasma are charged negatively and are subject to various types of forces, including a drag force by plasma particles and a force due to the collective nature of a plasma. Dust particles are found in a sheath in laboratories balanced by the gravitational force and the electric force, while dust particles in space are ubiquitous, including planetary magnetospheres and interstellar space. Because of the novel nature of a complex system involving plasma particles and dust particles in a collective way, the dusty plasma is often called a complex plasma. The complex plasma is characterized by two distinctly different scales in time and in space. The plasma with electrons, ions and neutrals is characterized by the collective motion with a fast time scale and a short wavelength, while the dust particles move in a slow time scale and a long spatial scale. Some fundamental aspects of a complex plasma are reviewed and possible applications are discussed. ...

Energy Technology Data Exchange (ETDEWEB)

This document contains the complete printout of the MICON A/S system configuration used in the Plutonium Finishing Plant. The document is divided into several volumes. Volume 1 covers the workstation display and configuration. All other volumes contain the controller configurations, or programs.

Science.gov (United States)

Dec 9, 2008 ... This page describes the procedures to configure certain browsers to automatically start Java Web Start applications...

Energy Technology Data Exchange (ETDEWEB)

The kinetic energy transferred to some elements by an electron of kinetic energy 100 to 400 kV is discussed. The displacement rates are compared to the signal generation. (DCL)

Science.gov (United States)

... Accession Number : ADA539720. Title : A Hybrid Kinetic Model of Asymmetric Thin Current Sheets with Sheared Flows in a Collisionless Plasma. ...

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Past airfoil configurations have been used to improve aerodynamic performance and engine efficiencies. The present airfoil configuration further increases component life and reduces maintenance by reducing internal stress within the airfoil itself. The airfoil includes a chord and a span. Each of the chord and the span has a bow being summed to form a generally "C" configuration of the airfoil. The generally "C" configuration includes a compound bow in which internal stresses resulting from a thermal temperature gradient are reduced. The structural configuration reduces internal stresses resulting from thermal expansion.

International Nuclear Information System (INIS)

... females in vitro intestines lead 203 mucous membranes radionuclide kinetics

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

UK PubMed Central (United Kingdom)

Peptide toxins with high affinity, divergent pharmacological functions, and isoform-specific selectivity are powerful tools for investigating the structure-function relationships of voltage-gated...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Monte Carlo neutron transport methods can be used to verify the applicability of point kinetics for safety analysis of nuclear reactors. KENO-NR was used to obtain the transfer function of the Advanced Neutron Source reactor and the time delay between the core power production and the external detectors, a parameter of interest to the safety systems design. The good agreement between the Monte Carlo generated transfer function and the point kinetics transfer function validates that the uncommon ANS geometry does not preclude the use of point kinetics in the frequency range that was investigated. Various features of the power spectral densities also demonstrated the applicability of point kinetics. The time delay was obtained from the cross-power spectral density (CPSD) and is {approximately}15 ms. These analyses show that frequency analysis can be used experimentally to investigate the validity of the ...

Science.gov (United States)

... Title : FINITE ELEMENT OPTIMIZATION OF FIELD CONFIGURATION FOR THE EDDY CURRENT TESTING OF ROLLER BEARING RIB RINGS. ...

International Nuclear Information System (INIS)

O close-quote Neil and Smith [T.M. O close-quote Neil and R.A. Smith, Phys. Plasmas 1, 8 (1994)] have argued that a pure electron plasma can be confined stably in a toroidal magnetic field configuration. This paper shows that the toroidal curvature of the magnetic field of necessity causes slow cross-field transport. The transport mechanism is similar to magnetic pumping and may be understood by considering a single flux tube of plasma. As the flux tube of plasma undergoes poloidal ExB drift rotation about the center of the plasma, the length of the flux tube and the magnetic field strength within the flux tube oscillate, and this produces corresponding oscillations in T_p_a_r_a_l_l_e_l and T_p_e_r_p_e_n_d_i_c_u_l_a_r. The collisional relaxation of T_p_a_r_a_l_l_e_l toward T_p_e_r_p_e_n_d_i_c_u_l_a_r produces a slow dissipation of electrostatic energy into heat and a consequent expansion (cross-field transport) of the plasma. In the limit where the cross section of ...

UK PubMed Central (United Kingdom)

BackgroundWe investigated the influence of parenteral glucose infusion on insulin-driven tight glucose control (4.4–6.1 mmol/liter) in the critically ill by appraising kinetic...Full Text Available

UK PubMed Central (United Kingdom)

Several compact proton accelerator systems for use in proton therapy have recently been proposed. Of paramount importance to the development of such an accelerator system is the maximum kinetic energy...Full Text Available

UK PubMed Central (United Kingdom)

Pyrophosphate:fructose-6-phosphate phosphotransferase (PFP) was purified over 500-cold from endosperm of germinating castor bean (Ricinus commiunis L. var. Hale). The kinetic properties...Full Text Available

UK PubMed Central (United Kingdom)

A specific immunoglobulin, the receptor antibody, can be found in most patients with myasthenia gravis. In order to study the kinetic properties of this antibody, serial determinations of receptor antibody,...Full Text Available

UK PubMed Central (United Kingdom)

Fibroblast cell population kinetics in the developing molar periodontal ligament was investigated in 10, 12, 16 and 20 days old mice by autoradiography after the administration of [3H]thymidine. Labelled...Full Text Available

UK PubMed Central (United Kingdom)

BACKGROUND AND OBJECTIVE:For treatment of benign prostatic hyperplasia (BPH), Plasma Kinetic loop Resection of the Prostate (PKRP) is an alternative to conventional monopolar...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

This report describes experimental results for the selective removal of strontium and cesium from simulated waste solutions using monosodium titanate (MST) and crystalline silicotitanate (CST)-laden filter cartridges. Four types of ion exchange cartridge media (CST and MST designed by both 3M and POROX{reg_sign}) were evaluated. In these proof-of-principle tests effective uptake of both Sr-85 and Cs-137 was observed. However, the experiments were not performed long enough to determine the saturation levels or breakthrough curve for each filter cartridge. POREX{reg_sign} MST cartridges, which by design were based on co-sintering of the active titanates with polyethylene particles, seem to perform as well as the 3M-designed MST cartridges (impregnated filter membrane design) in the uptake of strontium. At low salt simulant conditions (0.29 M Na{sup +}), the instantaneous decontamination factor (D{sub F}) for Sr-85 with the 3M-design MST cartridge measured 26, representing the removal of ...

Energy Technology Data Exchange (ETDEWEB)

Isothermal transformation kinetics of austenite to acicular ferrite and allotriomorphic ferrite were measured in reheated low alloy steel weld deposits with similar weld compositions and austenite grain size but different inclusion characteristics. Accelerated kinetics of transformation to acicular ferrite were observed in weld metal containing coarser and titanium-rich inclusions. In contrast, kinetics of transformation to allotriomorphic ferrite were not influenced by inclusion characteristics, but, rather, by the austenite grain size and carbon concentration.

Energy Technology Data Exchange (ETDEWEB)

This work deals with kinetic description of carbothermic reduction of iron oxides using microwaves as power source. Previous researches show that it is possible to conduct this kind of process successfully, but real kinetic comparisons between conventional and microwaves procedure have been presented partially. The aim of this work is to describe reduction kinetics, taking into account how the iron oxide is reduced by microwaves compared with conventional energy supply. In this study the authors used iron ore in pellet shape and dust. They found that both, pellet and dust reduction stops when it reaches approximately 40%, even at whole power.

Energy Technology Data Exchange (ETDEWEB)

Studies dialysis kinetics of zinc dialkyldithiophosphates, detergent-dispersing agents, alkyl-phenols and base oils. It was established that diffusion kinetics of oil hydrocarbons through membrane of individual compounds and narrow fractions is described by Brinzinger's formula, which is identical to the kinetic reaction formula of the 1st order. It was shown that dialysis can be utilized to determine the content of the ''active substance'' only in sulphonate and alkylsalycilate additives. Increasing temperature from 20 to 40/sup 0/ results in an increased dialysis constant for all studied products by 1.4-1.9 times.

Energy Technology Data Exchange (ETDEWEB)

The baryogenesis process in the early hot universe is investigated by means of relativistic kinetic theory. An exact solution to the kinetic equations for supermassive bosons serves to refine previous results: the optimum baryon-production domain is now complemented by bosons of low mass, thus removing the cosmological lower bound that had limited the mass of superheavy bosons. 14 references.

International Nuclear Information System (INIS)

The kinetics of lead distribution was studied in suckling and adult rats 8 days after a single intraperitoneal injection of "2"0"3Pb. Marked differences were observed in the kinetics of lead retention and distribution in suckling as compared to adult rats. The rate of "2"0"3Pb disappearance was lower in the whole body, blood and kidneys, but higher in the liver, while the deposition processes predominated in the brain, femur and teeth of sucklings as compared to adult animals. (auth).

Energy Technology Data Exchange (ETDEWEB)

Thermodynamic analysis of dissolution processes of tungsten minerals in citric acid solutions in the absence and in the presence of hydrochloric acid has been carried out by means of calculation of Gibbs energy of the chemical reactions. Kinetic characteristics, such as specific dissolution rates and activation energies, are determined. It is established that the dissolution reactions studied take place in kinetic region. A possibility of scheelite selective dissolution in the presence of other tungsten minerals is shown.

Science.gov (United States)

Four-enzyme section of the shikimate pathway (Aro B, D, E, and K) of Streptococcus pneumoniae has been studied. Kinetic properties of the individual enzymes and three- and four-enzyme linked reactions have been characterized in vitro. On the basis of the data measured in spectrophotometric and LC-MS experiments, kinetic mechanisms of the enzymes have been suggested and all kinetic parameters have been identified. Kinetic models for these three- and four-enzyme sections of the shikimate pathway have been constructed and validated. The model of the four-enzyme section of shikimate pathway has been employed to design an inhibition-sensitive reconstituted pathway for a high-throughput screening effort on the shikimate pathway. It was demonstrated that using the model it was possible to optimize this reconstituted pathway in such a way to provide equal sensitivity of the enzymes to inhibition. PMID:16921527

Energy Technology Data Exchange (ETDEWEB)

A detailed chemical kinetic reaction mechanism is developed to describe incineration of the chemical warfare nerve agent sarin (GB), based on commonly used principles of bond additivity and hierarchical reaction mechanisms. The mechanism is based on previous kinetic models of organophosphorus compounds such as TMP, DMMP and DIMP that are often used as surrogates to predict incineration of GB. Kinetic models of the three surrogates and GB are then used to predict their consumption in a perfectly stirred reactor fueled by natural gas to simulate incineration of these chemicals. Computed results indicate that DIMP is the only one of these surrogates that adequately describes combustion of GB under comparable conditions. The kinetic pathways responsible for these differences in reactivity are identified and discussed. The most important reaction in GB and DIMP that makes them more reactive than TMP or DMMP ...

Energy Technology Data Exchange (ETDEWEB)

Non-first order (FO) kinetics models are of three types; second order (SO), general order (GO) and mixed order (MO). It is shown that all three of these have constraints in their energy level schemes and their applicable parameter values. In nature such restrictions are not expected to exist. The thermoluminescence (TL) glow peaks produced by these models shift their position and change their shape as the trap occupancies change. Such characteristics are very unlike those found in samples of real materials. In these models, in general, retrapping predominates over recombination. It is shown that the quasi-equilibrium (QE) assumption implied in the derivation of the TL equation of these models is quite valid, thus disproving earlier workers' conclusion that QE cannot be held under retrapping dominant conditions. However notwithstanding their validity, they suffer from the shortcomings as stated above and have certain lacunae. For example, the ...

Science.gov (United States)

... VALIDATING NETWORK SECURITY POLICIES VIA STATIC ANALYSIS OF ROUTER ACL CONFIGURATION by Eric Gregory Wen Wei Wong ...

Science.gov (United States)

Variations,of-the ,rudder pedel force with.indicated airspeed are shown in figure 16 for the six vertical-tail configurations. -tested. ...

Science.gov (United States)

Disclosed in this proposal are plans to construct a patent pending wrist module with computer control, configurable to form high-dexerity telerobotic arms ...

International Nuclear Information System (INIS)

The level structure of "2"1"2Bi has been studied by observing the alpha decay of "2"1"6At which is in secular equilibrium with "2"2"0Fr and "2"2"4Ac. Eight states are observed and tentatively assigned to the configuration #pi#h_9_/_2#nu#(g_9_/_2)"3 and three to the configuration #pi#h_9_/_2#nu#(g_9_/_2)"2i_1_1_/_2. These two lowest configurations in "2"1"2Bi are compared with the corresponding configurations in "2"1"0Bi and the calculations of Warburton.

Energy Technology Data Exchange (ETDEWEB)

An overview is provided of an evolving atomistic and kinetic model of semiconductor growth that unifies the main features of strain relaxation in low and high lattice misfit heteroepitaxy. The model reveals a kinetic pathway for dislocation formation during growth with little or no energy cost at low misfits, thus providing a way out of the longstanding dilemma of too high dislocation nucleation energies predicted by classical theories of the equilibrium behavior of a fixed number of particles at low misfits. The essential kinetic process underlying the model are identified on the basis of comparison of the predictions of kinetic Monte-Carlo simulations of growth with real-time or in-situ data obtained in such experiments as reflection high-energy electron diffraction (RHEED) and scanning probe microscopy (SPM). Relative significance of these atomistic kinetic processes is shown to ...

International Nuclear Information System (INIS)

Kinetics of decomposition of gallium and alkali metal intermetallic compounds in the systems LiGa-LiOH, LiGa-NaOH and LiGa-KON was studied in the temperature range of 40-80 deg C. It was ascertained that increase in temperature gives rise to increase in decomposition rate, whereas increase in hydroxide concentration involves the reaction deceleration. An assumption was made that the decomposition occurs with superimposing of two mechanisms, i.e. chemical and electrochemical decomposition. Basic kinetic characteristics of the process were determined - decomposition rate constant and current density

Energy Technology Data Exchange (ETDEWEB)

The development of detailed chemical kinetic reaction mechanisms for analysis of autoignition and knocking of hydrocarbon fuels is described. In particular, kinetic processes of concern for the oxidation of complex hydrocarbon fuel molecules are emphasized. The wide ranges of temperature and pressure which are encountered by end gases in automobile engine combustion chambers result in extreme demands on reaction mechanisms which are intended to describe knocking conditions and predict rates of combustion and ignition. The reactions and chemical species which are most important in each temperature and pressure regime are discussed, and the validation of these reaction mechanisms through comparison with idealized experimental results is described. 53 refs., 8 figs., 5 tabs.

International Nuclear Information System (INIS)

A new method for kinetic experiments with neutrons is described. This method combines the conventional triple-axis neutron spectroscopy with relaxation-type experiments. Whereas the former method yields information about the microscopic dynamics of solids, the latter provides macroscopic relaxation times. The combination of both methods allows to determine the microscopic mechanism of relaxation processes. The time-resolved triple-axis spectroscopy is limited to reversible processes and to time scales from 10"-"3 to 10"4 s. Typical applications are the kinetics of phase transformations (structural and dynamical changes), kinetics of domain distributions, kinetics of (spinodal) decomposition, reversible solid state reactions, time-dependent occupation of phonon states or phonon lifetimes. (orig.).

Science.gov (United States)

... determination of the molar extinction coefficients, e, were measured by the Lowry method with native a-toxin as a standard. Binding Kinetics. ...

CERN Document Server

In this paper, we discuss the large--time behavior of solution of a simple kinetic model of Boltzmann--Maxwell type, such that the temperature is time decreasing and/or time increasing. We show that, under the combined effects of the nonlinearity and of the time--monotonicity of the temperature, the kinetic model has non trivial quasi-stationary states with power law tails. In order to do this we consider a suitable asymptotic limit of the model yielding a Fokker-Planck equation for the distribution. The same idea is applied to investigate the large-time behavior of an elementary kinetic model of economy involving both exchanges between agents and increasing and/or decreasing of the mean wealth. In this last case, the large-time behavior of the solution shows a Pareto power law tail. Numerical results confirm the previous analysis.

UK PubMed Central (United Kingdom)

To express growth-related changes in physiologic or other functions in forms usable for kinetic modeling, we are interested in identifying regular relationships that take the form of simple mathematical...Full Text Available

Science.gov (United States)

Aug. 24, 1965. L. V. BALDWIN ETAL. 3202915. PARTICLE BEAM MEASUREMENT APPARATUS USING BEAM KINETIC. ENERGY TO CHANGE TIIE HEAT SENSITIVE RESISTANCE OF ...

Science.gov (United States)

... defense's weapons are Space-based kinetic-kill vehicles ... I ti I obtained by dividing the weapons as ... of the optimal weapon-arge assigntments and ...

British Library Electronic Table of Contents (United Kingdom)

A detailed chemical kinetic reaction mechanism is developed for primary reference fuel mixtures of n-hexadecane and 2,2,4,4,6,8,8-heptamethyl nonane for diesel cetane ratings. The mechanisms are constructed using existing rules for reaction pathways and rate expressions developed previously for the primary reference fuels for gasoline octane ratings, n-heptane and iso-octane. These reaction mechanisms are validated by comparisons between computed and experimental results for shock tube ignition and for oxidation under jet-stirred reactor conditions. The combined kinetic reaction mechanism contains the submechanisms for the primary reference fuels for diesel cetane ratings and submechanisms for the primary reference fuels for gasoline octane ratings, all in one integrated large kinetic reac...

Science.gov (United States)

The concentration decay curves for the adsorption of phenol on organobentonite were obtained in an agitated tank batch adsorber. The experimental adsorption rate data were interpreted with diffusional models as well as first-order, second-order and Langmuir kinetic models. The surface diffusion model adjusted the data quite well, revealing that the overall rate of adsorption was controlled by surface diffusion. Furthermore, the surface diffusion coefficient increased raising the mass of phenol adsorbed at equilibrium and was independent of the particle diameter in the range 0.042-0.0126cm. It was demonstrated that the overall rate of adsorption was essentially not affected by the external mass transfer. The second-order and the Langmuir kinetic models fitted the experimental data quite well; however, the kinetic constants of both models varied without any physical meaning while increasing the particle size and the mass of ...

Science.gov (United States)

Mar 1, 2011... properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. ...

Energy Technology Data Exchange (ETDEWEB)

In this paper the possibility of configuring a water cooled Nuclear Thermal Propulsion (NTP) rocket, based on a Particle Bed Reactor (PBR) is investigated. This rocket will be used to operate on water obtained from near earth objects. The conclusions reached in this paper indicate that it is possible to configure a PBR based NTP rocket to operate on water and meet the mission requirements envisioned for it. No insurmountable technology issues have been identified.

Energy Technology Data Exchange (ETDEWEB)

An electrical circuit testing device is provided, comprising a case, a digital voltage level testing circuit with a display means, a switch to initiate measurement using the device, a non-shorting switching means for selecting pre-determined electrical wiring configurations to be tested in an outlet, a terminal block, a five-pole electrical plug mounted on the case surface and a set of adapters that can be used for various multiple-pronged electrical outlet configurations for voltages from 100 600 VAC from 50 100 Hz.

International Nuclear Information System (INIS)

K?-to-K? X-ray intensity ratios of Ti and Ni have been measured in pure metals and in alloys of TixNi1-x (x=0.7, 0.6, 0.5, 0.4 and 0.3) following excitation by 22.69 keV X-rays from a 10 mCi 109Cd radioactive point source. The valence-electron configurations of these metals were determined by corporation of measured K?-to-K? X-ray intensity ratios with the results of multiconfiguration Dirac-Fock calculation for various valence-electron configurations. Valence-electron configurations of 3d-transition metals in alloys indicate significant differences with respect to the pure metals. Our analysis indicates that these differences arise from delocalization and/or charge transfer phenomena in alloys. Namely, the observed change of the valence-electron configurations of metals in alloys can be explained with the transfer of 3d electrons from one element to the other element and/or the rearrangement of ...

CERN Document Server

The first quantitative evaluation of the quality of corporate firewall configurations appeared in 2004, based on Check Point FireWall-1 rule-sets. In general that survey indicated that corporate firewalls were often enforcing poorly written rule-sets, containing many mistakes. The goal of this work is to revisit the first survey. The current study is much larger. Moreover, for the first time, the study includes configurations from two major vendors. The study also introduce a novel "Firewall Complexity" (FC) measure, that applies to both types of firewalls. The findings of the current study indeed validate the 2004 study's main observations: firewalls are (still) poorly configured, and a rule-set's complexity is (still) positively correlated with the number of detected risk items. Thus we can conclude that, for well-configured firewalls, ``small is (still) beautiful''. However, unlike the 2004 study, we ...

Science.gov (United States)

We study a kinetic model for a system of two species of particles interacting via a repulsive long range potential and with a reservoir at fixed temperature. The interaction between the particles is modeled by a Vlasov term and the thermal bath by a Fokker-Planck term. We show that in the diffusive and sharp interface limit the motion of the interfaces at low temperature is described by a Stefan problem or a Mullins-Sekerka motion, depending on the time scale.

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the hydrolysis of polyacrylonitrile in aqueous and aqueousalcoholic solution have been studied. The effects of the solvent on the kinetics of the hydrolysis have been demonstrated, together with the role of diffusion and adsorption of the hydrolyzing agent on the surface of the macromolecules. It has also been shown to be possible to control the extent of hydrolysis and the hydrophilicity of the product.

International Nuclear Information System (INIS)

Studies have been performed with an anti-osteogenic sarcoma monoclonal antibody 791T/36 and human tumour xenografts to examine some of the quantitative and kinetic aspects of tumour localization. The influence of variations in tumour size and site and antibody dose on the extent and rate of specific antibody localization have been examined, together with the site of intratumoural deposition of the antibody. (UK).

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the reaction of carbon dioxide in MDEA solutions were studied both experimentally and theoretically. It is concluded that MDEA acts as a homogeneous catalyst for CO/sub 2/ hydrolysis, and as a result the rate of absorption in aqueous MDEA solutions is significantly larger than one would calculate by simply taking into account the alkalinity of the reaction. A possible zwitterion mechanism is proposed for this reaction. The minor effect of ionic strength were also studied with the presence of other ions. 19 references, 6 figures.

CERN Document Server

We construct a chaotic inflation model in which the Higgs fields play the role of the inflaton in the singlet extension of the supersymmetric standard model. The key idea is to impose a shift symmetry on the D-flat direction Hu Hd in the Kahler potential. The model is a realization of the recently proposed running kinetic inflation, in which the coefficient of the kinetic term grows as the inflaton field. The inflaton potential depends on the structure of the Higgs sector. For instance, the inflaton potential is proportional to phi^{2/3} during inflation in the NMSSM.

Energy Technology Data Exchange (ETDEWEB)

Primary dendrite spacings and side-branch coarsening kinetics were examined in specimens of the single-crystal multicomponent commercial superalloy PWA-1480, which were directionally solidified in a psoitive thermal gradient. The experimentally observed dependence of primary dendrite spacings and side-branch coarsening kinetics on growth rate and thermal gradient were in agreement with the behavior predicted by analytical models developed for binary alloys. (orig.).

International Nuclear Information System (INIS)

A simple model is described to simulate kinetic processes in dielectric barrier discharges for O_2/NO_x mixtures. A threshold of ozone production found experimentally is confirmed by the calculations of this modeling, and the underlying chemical reaction mechanisms are discussed. It is also found that the effects of diffusion processes in the period of the lifetime of O atoms are not important to micro-discharge channels with a large radius, i.e. larger than 150 #mu#m

International Nuclear Information System (INIS)

Kinetic Monte Carlo (KMC) computer simulations are performed to determine the kinetics of SIA cluster 'clouds' in the vicinity of edge dislocations. The simulations include elastic interactions amongst SIA clusters, and between clusters and dislocations. Results of KMC simulations that describe the formation of 'SIA clouds' during neutron irradiation of bcc Fe and the corresponding evolution kinetics are presented, and the size and spatial distribution of SIA clusters in the cloud region are studied for a variety of neutron displacement damage dose levels. We then investigate the collective spatio-temporal dynamics of SIA clusters in the presence of internal elastic fields generated by static and mobile dislocations. The main features of the investigations are: (1) determination of the kinetics and spatial extent of defect clouds near static dislocations; (2) assessment of the influence of localized ...

Energy Technology Data Exchange (ETDEWEB)

The study discussed relates to the design and development of a process consisting of combining a reversible geothermal heat pump with thermal solar collectors for building heating and cooling and the production of domestic hot water. The proposed process, called GEOSOL, has been installed in a 180 m{sup 2} private residence in 2004. This installation is the subject of long-term experimental follow-up to analyse the energy-related behavior of the installation at all times of the year. In addition, different configurations of this combined system (geothermal heat pump and thermal solar collectors) have been defined and will be simulated numerically using TRNSYS software. A comparative analysis of these different alternative versions will be conducted to determine the best configuration(s) of the GEOSOL process in terms of energy, economical and environmental performances. (author)

Energy Technology Data Exchange (ETDEWEB)

This document is the final report for Cooperative Agreement DE-FC26-04NT42314, 'Kinetics Study of Mercury Reactions in FGD Liquors'. The project was co-funded by the U.S. DOE National Energy Technology Laboratory and EPRI. The objective of the project has been to determine the mechanisms and kinetics of the aqueous reactions of mercury absorbed by wet flue gas desulfurization (FGD) systems, and develop a kinetics model to predict mercury reactions in wet FGD systems. The model may be used to determine optimum wet FGD design and operating conditions to maximize mercury capture in wet FGD systems. Initially, a series of bench-top, liquid-phase reactor tests were conducted and mercury species concentrations were measured by UV/visible light spectroscopy to determine reactant and byproduct concentrations over time. Other measurement methods, such as atomic absorption, were used to measure concentrations of ...

UK PubMed Central (United Kingdom)

Many healthcare organizations utilize network "firewalls" to protect their networks from being accessed by unauthorized external entities. These same firewalls are also often configured to deny access...Full Text Available

International Nuclear Information System (INIS)

There are 173 three quasiparticle rotational bands, out of which 38 bands display signature splitting and sometimes a signature inversion also. The observed signature splitting is basically due to the higher order Coriolis coupling and calculation based on particle rotor model (PRM) are in progress

Energy Technology Data Exchange (ETDEWEB)

A number of technical requirements and performance criteria can drive stellarator costs, e.g., tight tolerances, accurate coil positioning, low aspect ratio (compactness), choice of assembly strategy, metrology, and complexity of the stellarator coil geometry. With the completion of a seven-year design and construction effort of the National Compact Stellarator Experiment (NCSX) it is useful to interject the NCSX experience along with the collective experiences of the NCSX stellarator community to improving the stellarator configuration. Can improvements in maintenance be achieved by altering the stellarator magnet configuration with changes in the coil shape or with the combination of trim coils? Can a mechanical configuration be identified that incorporates a partial set of shaped fixed stellarator coils along with some removable coil set to enhance the overall machine maintenance? Are there other approaches that will ...

UK PubMed Central (United Kingdom)

Combined QM(PM3)/MM molecular dynamics simulations together with QM(DFT)/MM optimizations for key configurations have been performed to elucidate the enzymatic catalysis mechanism on the detoxification...Full Text Available

Science.gov (United States)

... 1 8.53 1.5448 2 12.45 2.1944 3 16.59 2.5224 Sensor Mobility fixed 8.92 1.9312 mobile 12.15 2.3625 Display Configuration conv. 10.92 1.7981 ...

Energy Technology Data Exchange (ETDEWEB)

A design of the modular coil system for CHS-qa has been made for the plasma configuration '2b32' with the aspect ratio 3.2. The magnetic field strength and the major radius are 1.5 T and 1.5 m, respectively. The normal component of magnetic field produced by the modular coils is minimized on the plasma boundary to obtain the optimum coil design. We put engineering constraint on the distance between adjacent modular coils and the radius of coil curvature. The dependence of the residual normal component of the field on these conditions is examined, and the realistic values for them are selected. Additional coils to control various properties of the magnetic field configuration (the rotational transform, the magnetic well depth, etc.) have been designed and a flexibility of the magnetic field configuration is realized. For the case that the rotational transform crosses the low-order rational value resulting ...

Energy Technology Data Exchange (ETDEWEB)

A general model for wakefield-generated instabilities in linear accelerators, originally developed for cumulative beam breakup [1], is applied to the resistive wall instability. The general solution for various bunch charge distributions and application to various accelerator configurations are presented.

Energy Technology Data Exchange (ETDEWEB)

In pre-experiments a tubular reactor was checked whether it is suitable for kinetic measurement on the system of the silver-catalysed partial oxidation of methanol to formaldehyde. Detrimental effects of heat-transfer and mass-transfer on the experimental results were ruled out. Investigations on the characteristics of the reaction showed that it is possible to manipulate the composition of the product mixture by changing the inlet concentration of the reactants. A modified power-law model was established to describe the reaction kinetics. It considers the preadsorption step of oxygen on the catalysts surface and fits the experimental data quite well. During the rapid oxidation the catalysts surface undergoes a drastic change. It gets coarse and has an adsorption capacity of 11 m{sup 2}/g after being exposed to the reaction mixture. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The potential of waste seashells powder, as a new adsorbent for Brilliant Red HE-3B reactive dye removal from aqueous solutions, was examined by the batch technique. The Freundlich, Langmuir, and Dubinin-Radushkevich adsorption models were applied to describe the equilibrium sorption data and to determine the corresponding isotherm constants. The values of the thermodynamic parameters, ?G, ?H, and ?S, indicate that the sorption of reactive dye is a spontaneous and endothermic process. The kinetic data evaluated by pseudo-first order, pseudo-second order, and intraparticle diffusion kinetic models suggested that the sorption of reactive dye onto seashell is a complex process and both surface sorption and intraparticle diffusion contributes to the rate limiting step.

Energy Technology Data Exchange (ETDEWEB)

The design of a reaction cell which permits the investigation of the sorption kinetics of microcomponents without separation of the phases under automated condition has been described. The use of thin-layer inorganic sorbents obtained by depositing films of a sorbing substance from aqueous solutions on flat substrates of small thickness makes it possible to determine the extent of sorption even at small values in the case of /beta/ emitters with a low energy and /alpha/ emitters. Detailed observation of the kinetics of isotopic exchange in the CdS-/sup 115m/Cd-HNO/sub 3/ system has made it possible to reveal at least four stages in the process during the time of observation.

British Library Electronic Table of Contents (United Kingdom)

A dense Pd-Ag membrane reactor (MR) with 100% hydrogen selectivity packed with either Rh/La2O3 or Rh/La2O3-SiO2 as catalysts was used to carry out the dry reforming of methane. The membrane reactor simulation was performed using a well-known reactor model. For this purpose, we employed the equations derived from complete kinetic studies of the dry reforming of methane reaction in connection with both catalysts. In addition, we developed the kinetic equation for the reverse water gas shift reaction (RWGS). The combination of detailed kinetic studies with the measured permeation flux for the Pd-Ag membrane allowed a complete comparison between experimental and simulated operation variables. The variables studied for both catalysts were methane conversion and hydrogen permeation as a function...

Energy Technology Data Exchange (ETDEWEB)

The temperature and concentration dependence of the kinetics of uranium(VI) ions adsorption onto activated charcoal from aqueous solutions has been studied. The adsorption proceeds via a rather fast stage followed by a slower one, with activation energies of 5.41 and 17.46 kJ . mol[sup -1] respectively. The diffusion of uranium ions into the pores of the activated charcoal controls the kinetics of adsorption which follows the Langmuir isotherm equation in the concentration range studied. The adsorption equilibrium constant k[sub c] has been derived at temperatures between 283 K and 323 K as well as [Delta] G, [Delta] H and [Delta] S. The results indicate that the adsorption of uranium ions on activated charcoal is an endothermic process. (orig.)

Science.gov (United States)

The kinetic rate constants for the cracking, isomerization, and disproportionation of n-heptane over a CrHNaY (32% chromium exchanged) zeolite catalyst at 400, 450, and 470/sup 0/C have been calculated. The interaction of n-heptane with a model Lewis acid such as BF/sub 3/ and progress along the reaction coordinate have been studied by means of molecular orbital calculations. From the kinetic results, i.e., activation energies and frequency factors, and the theoretical calculations, it can be concluded that the controlling step in these reactions is not the formation of the carbonium ion, but the subsequent transformation of this carbonium ion. In addition, the theoretical calculations show that the attack of a Lewis acid is more likely to occur on a carbon atom than on a C-H bond.

Energy Technology Data Exchange (ETDEWEB)

Reactive chemical transport models developed over the past decade have generally relied on the assumption that local thermodynamic equilibrium is achieved at all times between aqueous species in a given system. Consequently, homogeneous aqueous systems characterized by a number of kinetically slow reactions, particularly problems involving organic species, cannot be satisfactorily modeled. In this study, we present a prototype computer model, KINETRAN, which is designed to handle kinetically-controlled homogeneous reactions in the aqueous phase, along with the transport of the various species involved, through geologic media. 31 refs., 53 figs., 10 tabs.

British Library Electronic Table of Contents (United Kingdom)

b-carotene, a natural antioxidant, beneficial form human health prospective. In this study we had examined the recovery of b-carotene form mesoporous carbon coated monolith (MCCM) by batch process. Desorption kinetics and isotherm studies were carried out by using n-hexane as an eluent. Isotherm studies showed better applicability of Langmuir model. The first-order two-compartment three-parameter kinetics model as a function of initial loading concentration and reaction temperature was applied. It was observed that b-carotene desorption process is controlled by both rapid and slow desorption. Results showed that the slow desorption fraction increases from 0.8446 to 0.9007 with increase in initial loading concentration from 10.83 to 39.72mg/g while, the slow desorption fraction decreases fr...

International Nuclear Information System (INIS)

The kinetics of the reactions between mixed powders of BaCO_3 and CuO, as well as BaCO_3 and Y_2O_3, have been studied using DXRD techniques as a function of particle size, temperature, and CO_2 pressure. Except for initial nucleation phenomena, the reaction rates are governed by shrinking core behavior for BaCO_3 particle sizes between 6 and 33 #mu#m. During the initial stages of the reactions, the surface reaction kinetics are governing, whereas the diffusion of CuO, Y_2O_3, and CO_2 are limiting factors at later stages in the reactions. Quantitative conversion data were used to determine the values of the activation energies and the pertinent diffusivities in these systems.

Energy Technology Data Exchange (ETDEWEB)

This project is concerned with the kinetics and mechanisms of aromatic oxidation and soot and fullerenes formation in flames. The objective of the aromatics oxidation work is to identify and measure the concentration of important intermediates and products in benzene oxidation, and to determine reaction mechanisms and kinetics properties consistent with the behavior seen in flames. The research on soot formation is concerned primarily with the particle inception stages, but the work includes study of soot structure at all stages of growth in order to obtain mechanistic information from evidence of growth steps recorded in the structure of the particles. The ultimate objective is to understand how nascent soot particles are formed from high molecular weight compounds, including the roles of planar and curved PAH and the relationship between soot and fullerenes. The objective of the proposed research on fullerenes is to develop a more ...

International Nuclear Information System (INIS)

We theoretically investigate the features of two-photon absorption in a coherently driven four-level atomic system with closed-loop configuration. It is found that two-photon absorption can be completely suppressed just by properly adjusting the relative phase of four coherent low-intensity driving fields and the atomic system becomes transparent against two-photon absorption. From a physical point of view, we explicitly explain these results in terms of quantum interference induced by two different two-photon excitation channels.

Energy Technology Data Exchange (ETDEWEB)

The theory for the general case of solar cells operating inside integrating cavity receivers is established. This is applied to the particular case of different configurations of silicon and GaAs cells. The results of the analysis show that a composite system of silicon and GaAs cells manufactured using relatively simple technology could reach an efficiency of 34%. The optimal configuration is that in which the GaAs cells are placed in the directly illuminated area of the receiver and the silicon cells are placed in the indirectly illuminated area of the receiver. (orig.).

Energy Technology Data Exchange (ETDEWEB)

The objective of Configuration Risk Management Program(CRMP) is to maintain the safety level by assuring the defense-in-depth of nuclear power plant while the configurations are changed during plant operations, especially for the LP/SD. Such a safety purpose can be achieved by establishing the risk monitoring programs with both quantitative and qualitative features. Generally, the quantitative risk evaluation models, i.e., PRA models are used for the risk evaluation during full power operation, and the qualitative risk evaluation models such as safety function assessment trees are used. Through this study, safety function assessment trees were developed.

Energy Technology Data Exchange (ETDEWEB)

Compact heat exchangers are being increasingly considered for condensation applications in the process, cryogenic, aerospace, power and refrigeration industries. In this paper, different configurations available for condensation applications are analyzed and the current state-of-the-knowledge for the design of compact condensers is evaluated. The key technical issues for the design and development of compact heat exchangers for condensation applications are analyzed and major advantages are identified. The experimental data and performance prediction methods reported in the literature are analyzed to evaluate the present design capabilities for different compact heat-exchanger configurations. The design flexibility is evaluated for the development of new condensation applications, including integration with other process equipment.

Energy Technology Data Exchange (ETDEWEB)

A thermophotovoltaic (TPV) generator for electric vehicles has been designed and developed. In this paper we focus on the combustion system and the heat regenerator. The system has been designed to work as a range extender for electric vehicles. This solution would provide energy always available on the vehicle, which would run even if the battery level were low. Several configurations for the burner and for the heat exchanger have been investigated and a comparison of these is presented. The different solutions have been studied both theoretically and experimentally. In this paper, we report on the work carried out to build a TPV device capable of yielding 6 kW of electric power to recharge the battery pack of an electric city-car. The project has been divided into four steps: (1) pre-design of different configurations of the burner and heat exchanger using non-commercial software 'TPV Design Tool 1.0'; (2) testing of the ...

UK PubMed Central (United Kingdom)

Uracil appears in DNA as a result of cytosine deamination and by incorporation from the dUTP pool. As potentially mutagenic and deleterious for cell regulation, uracil must be removed from DNA....Full Text Available

UK PubMed Central (United Kingdom)

The trematode Fasciola hepatica (Fa.he.) is a common parasite of human and livestock. The hemoglobin (Hb) of Fa.he., a potential immunogen, was chosen for characterization...Full Text Available

UK PubMed Central (United Kingdom)

Sucrose uptake by discs of mature sugar beet root tissue incubated in [¹⁴C]-sucrose exhibited nonsaturating kinetics over the concentration range of 1 to 500 millimolar. Uptake was inhibited...Full Text Available

UK PubMed Central (United Kingdom)

In vivo short-term effects of recombinant human TNF-alpha on lipolysis, FFA flux, fat oxidation, triglyceride-fatty acid cycling, and glucose kinetics were evaluated with stable isotopic tracers and...Full Text Available

UK PubMed Central (United Kingdom)

To investigate the role of thyroxine-binding globulin (TBG) and albumin in the availability of thyroid hormones to peripheral tissues, comprehensive kinetic studies of thyroxine (T4) and triiodothyronine...Full Text Available

UK PubMed Central (United Kingdom)

Edema factor (EF) and CyaA are calmodulin (CaM)-activated adenylyl cyclase exotoxins involved in the pathogenesis of anthrax and whooping cough, respectively. Using spectroscopic, enzyme kinetic and...Full Text Available

UK PubMed Central (United Kingdom)

In this study we use the multiple indicator dilution technique to outline the kinetic mechanisms underlying the uptake of rubidium, a cation which, in the steady state, is concentrated by hepatic parenchymal...Full Text Available

UK PubMed Central (United Kingdom)

CTX-M-25 is a novel extended-spectrum β-lactamase isolated from a single Canadian Escherichia coli isolate. Susceptibility testing demonstrated that this enzyme confers resistance...Full Text Available

International Nuclear Information System (INIS)

Heterogeneous gasless reactive systems, including high-energy density metal-nonmetal compositions, have seen increasing study due to their various applications. However, owing to their high reaction temperature, short reaction time, and small scale of heterogeneity, investigation of their reaction mechanisms and kinetics is very difficult. In this study, microstructural changes and the kinetics of product layer growth in the W-Si system was investigated using a high-speed x-ray phase-contrast imaging technique. Using the Advanced Photon Source of Argonne National Laboratory, this method allowed direct imaging of irreversible reactions in the W-Si reactive system at frame rates up to 36 000 frames per second with 4 #mu#s exposure and spatial resolution of 10 #mu#m. Details of the Si melt and reactions between W and Si, that are unable to be viewed with visible-light imaging, were revealed. These include processes such as the initiation of ...

Energy Technology Data Exchange (ETDEWEB)

A rapid filtration technique has been used to measure at room temperature the kinetics of ADP and ATP transport in rat heart mitochondria in the millisecond time range. Transport was stopped by cessation of the nucleotide supply, without the use of a transport inhibitor, thus avoiding any quenching delay. The kinetics of ({sup 14}C)ADP transport in energized mitochondria were apparently monophasic. The rate of transport of ({sup 14}C)ATP in energized mitochondria was 5-10 times lower than that of ({sup 14}C)ADP. Upon uncoupling, the rate of ({sup 14}C)ATP uptake was enhanced, and that of ({sup 14}C)ADP uptake was decreased. However, the two rates did not equalize, indicating that transport was not exclusively electrogenic. Transport of ({sup 14}C)ADP and ({sup 14}C)ATP by resting mitochondria followed biphasic kinetics. Depletion of nucleotides in resting mitochondria resulted in a greater decrease in the extent of the slow ...

International Nuclear Information System (INIS)

The first-order relativistic correction to the kinetic energy of an electron, the mass-velocity term, is not bounded from below. It can, therefore, not be used within a variational framework. To overcome this deficiency we developed a method to include the entire relativistic kinetic energy #sq root#(p"2c"2+m_0"2c"4)-m_0c"2 in a spline-augmented plane-wave band calculation. The first results for silver are quite promising, especially for d and p states: The analysis of the energies of the core states as well as of the valence band structure suggests that the energies of d bands are reproduced within 1 mRy. However, the combination of the relativistic kinetic energy with the Darwin term leads to energies which are too low for s-like valence states by 10 mRy. Therefore, the s and d valence band complex is spread out and the Fermi level is lowered by the same amount as the s states. We expect to overcome these deficiencies in ...

UK PubMed Central (United Kingdom)

In this report we define the parameters of the human immune response after immunization with hepatitis B vaccine. 2 wk after booster immunization, there is significant spontaneous secretion of antibody...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The electrode kinetics for oxygen reduction on conducting metal oxides, including lithiated NiO (formed in situ) and Sb-doped SnO/sub 2/, have been investigated. Kinetic measurements were carried out by using ac impedance and coulostatic relaxation methods. The ac behavior on the oxide electrodes was analyzed on the basis of a modified Randles-Ershler type equivalent circuit which takes into account the effect of non-faradaic components due to the semiconducting oxide films. The kinetic parameters (the charge transfer resistance and Warburg coefficient) and the interfacial parameters (the double layer capacity, film capacity and film resistance) were obtained by a least squares curve fitting method under P/sub O2//P/sub CO2/=0.9/0.1 atmosphere. The exchange current density was found to be 10 to 20 mA cm/sup -2/ at the oxide electrodes, assuming n=2. The coulostatic relaxation experiments supported the magnitude of the i/sub ...

UK PubMed Central (United Kingdom)

1 The influence of the nonsteroidal anti-inflammatory drug naproxen on glucose metabolism and on tolbutamide pharmacokinetics and pharmacodynamics has been studied in ten maturity-onset diabetics. 2...Full Text Available

UK PubMed Central (United Kingdom)

The continuous addition of toluene as a solute of treated ballast water from oil tankers into a well-defined estuary facilitated the study of the dynamics of dissolved hydrocarbon metabolism in seawater....Full Text Available

UK PubMed Central (United Kingdom)

A physiologically based pharmacokinetic (PBPK) model was developed that provides a comprehensive description of the kinetics of trichloroethylene (TCE) and its metabolites, trichloroethanol (TCOH),...Full Text Available

International Nuclear Information System (INIS)

The dependences of kinetic energies and peak profiles of multicharged ions of I "q"+ (q = 2-3) and C"2"+ on the laser intensity have been studied in detail by time-of-flight mass spectrometry, those multicharged ions are produced by irradiation of methyl iodide cluster beam with a nanosecond 532 nm Nd-YAG laser. Our experiments show that the kinetic energies released of multicharged ions increase linearly with the laser intensity in the range of 3 x 10"9-2 x 10"1"1 W/cm"2. The peaks of multicharged ions are split to forward ions and backward ions, and the ratio of the backward ions to forward ions decreases exponentially with laser intensity. The decreasing of backward ions is probably due to Coulomb scattering by the heavier I"+ ions when they turn around through the laser focus point. The linear dependence of kinetic energy of multicharged ions on laser intensity is interpreted by the ionization mechanism, in which the ...

UK PubMed Central (United Kingdom)

Mice homozygous for the recessive gene achondroplasia (cn) aged 16 and 17 days and some homozygotes aged 22-34 days have disruptions in the growth of the proximal tibial growth plate which are due solely...Full Text Available

UK PubMed Central (United Kingdom)

Differential scanning calorimetric (DSC) studies of the glassy states of as-received and hydrated lysozyme, hemoglobin, and myoglobin powders, with water contents of < or = 0.25, < or...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The isotherms, kinetics and thermodynamics of Cd(II), Zn(II) and Pb(II) biosorption by Penicillium simplicissimum were investigated in a batch system. The effects of pH, initial metal ions concentration, biomass dose, contact time, temperature and co-ions on the biosorption were studied. Adsorption data were well described by both the Redlich-Peterson and Langmuir model. Chemical ion-exchange was found to be an important process based on free energy value from Dubini-Radushkevich isotherm for all metal ions. The results of the kinetic studies of all metal ions at different temperature showed that the rate of adsorption followed the pseudo second-order kinetics well. The thermodynamics constants {delta}G{sup o}, {delta}H{sup o} and {delta}S{sup o} of the adsorption process showed that biosorption of Cd(II), Zn(II) and Pb(II) ions on Penicillium simplicissimum were endothermic and spontaneous.

UK PubMed Central (United Kingdom)

BackgroundKinematic and kinetic measurements used in laboratory settings can quantify upper extremity movement impairment following stroke, but their relationship...Full Text Available

UK PubMed Central (United Kingdom)

Single-channel currents from acetylcholine receptor channels of garter snake neuromuscular junctions were recorded using the patch-clamp technique. Low concentrations of acetylcholine or carbamylcholine...Full Text Available

UK PubMed Central (United Kingdom)

Transthyretin aggregation-associated proteotoxicity appears to cause several human amyloid diseases. Rate-limiting tetramer dissociation and monomer misfolding of transthyretin (TTR) occur before...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The research has involved the characterization of catalyst acidity, [sup 2]D NMR studies of Bronsted acid sites, and kinetic, calorimetric, and spectroscopic studies of methylamine synthesis and related reactions over acid catalysts. Approach of this work was to explore quantitative correlations between factors that control the generation, type, strength, and catalytic properties of acid sites on zeolite catalysts. Microcalorimetry, thermogravimetric analysis, IR spectroscopy, and NMR spectroscopy have provided information about the nature and strength of acid sites in zeolites. This was vital in understanding the catalytic cycles involved in methylamine synthesis and related reactions over zeolite catalysts.

International Nuclear Information System (INIS)

The wide-angle neutron diffractometer recently installed at the HFIR has the capability of performing time-resolved or time-slicing measurements. One of the interesting problem areas the authors have explored using this time-slicing function of the diffractometer is the kinetics of structural changes occurring after a temperature jump across a value at which a first-order phase transition occurs. Two measurements of this sort have been carried out: the phase III to II transition in RbNO_3 and the transition between the alpha and beta phases in Sn.

International Nuclear Information System (INIS)

Non-thermal plasma treatment is a promising technique for the destruction of volatile organic compounds in waste gas. A relatively unexplored technique is the atmospheric negative dc multi-pin-to-plate glow discharge. This paper reports experimental results of allyl alcohol degradation and ozone production in this type of plasma. A new model was developed to describe these processes quantitatively. The model contains a detailed chemical degradation scheme, and describes the physics of the plasma by assuming that the fraction of electrons that takes part in chemical reactions is an exponential function of the reduced field. The model captured the experimental kinetic data to less than 2 ppm standard deviation.

Energy Technology Data Exchange (ETDEWEB)

Direct electric heating by passing an electrical current directly through a bed of adsorbent may prove to be an efficient means of regenerating activated charcoal in continuous and batch adsorption processes. Obvious advantages of this type of regeneration are its almost complete lack of inertia, which makes it possible to reduce the number and dimensions of the adsorbers, and its highly efficient use of energy due to the small number of steps in the conversion of the energy, as well as the reduction of heat losses involved in warming the structure and making up for losses to the surroundings. The authors consider the kinetics of direct electric heating of a stationary bed of activated charcoal not containing adsorbed substances.

Energy Technology Data Exchange (ETDEWEB)

In the Joule II project JOU2-CT 94-0428 `Development and Testing of Stand-Alone small-size Solar Photovoltaic-Hydrogen power Systems (SAPHYS)`, different design configurations are compared and discussed. In this paper we present some of the proposed design configurations and discuss their benefits and drawbacks. Simplified expressions for system efficiency for the different configurations are presented. These expressions are based on average efficiencies for the solar cells, the electrolyzer, the batteries, the hydrogen storage and the fuel cells. Mean fractions of energy passing through the energy storages are also assumed. From considerations in the paper one conclusion becomes apparent, i.e. the direct use of the energy should be maximized. Another conclusion is that one of the most important factors in Solar Photovoltaic Hydrogen Power Systems is the solar cell efficiency. This point seems to be lost in typical projects ...

Science.gov (United States)

The investigation of various Two-Stage Liquefaction (TSL) process configurations was conducted at the Wilsonville Advanced Coal Liquefaction R D Facility between July 1982 and September 1986. The facility combines three process units. There are the liquefaction unit, either thermal (TLU) or catalytic, for the dissolution of coal, the Critical Solvent Deashing unit (CSD) for the separation of ash and undissolved coal, and a catalytic hydrogenation unit (HTR) for product upgrading and recycle process solvent replenishment. The various TSL process configurations were created by changing the process sequence of these three units and by recycling hydrotreated solvents between the units. This report presents a description of the TSL configurations investigated and an analysis of the operating and performance data from the period of study. Illinois No. 6 Burning Star Mine coal Wyodak Clovis Point Mine coal were processed. ...

Energy Technology Data Exchange (ETDEWEB)

Using a coplanar, end-mounted antenna as a baseline, various configuration trades were performed to select a preferred solid state concept. The increase in efficiency that could be realized by use of multi bandgap solar cells, either with klystron or solid state antenna was evaluated. Satellite configurations were developed to exploit the sandwich antenna concept wherein solar cells are located on one side of the antenna panel and solid state dc/RF converters on the other side. These concepts entailed various primary and secondary reflector arrangements for directing solar energy to the solar cell side of the antenna with higher concentration ratios than used on the coplanar configurations. Operations analysis included development of a satellite construction scenario, a concept for the SCB, a top-level satellite construction operation, construction operation, construction timelines and crew sizes, mass flows to orbit, and a ...

Energy Technology Data Exchange (ETDEWEB)

We discuss the possibility of extending solid state laser technology to high average power and of improving the efficiency of such lasers sufficiently to make them reasonable candidates for a number of demanding applications. A variety of new design concepts, materials, and techniques have emerged over the past decade that, collectively, suggest that the traditional technical limitations on power (a few hundred watts or less) and efficiency (less than 1%) can be removed. The core idea is configuring the laser medium in relatively thin, large-area plates, rather than using the traditional low-aspect-ratio rods or blocks. This presents a large surface area for cooling, and assures that deposited heat is relatively close to a cooled surface. It also minimizes the laser volume distorted by edge effects. The feasibility of such configurations is supported by recent developments in materials, fabrication processes, and optical pumps. Two types of ...

Energy Technology Data Exchange (ETDEWEB)

Sandia National Laboratories contracted with Rockwell International Science Center to perform a series of narrowband, pseudo-random cyclic fatigue tests on sections of 6063-T651 aluminum, Darrius-type, vertical axis wind turbine (VAWT) airfoils. We designed and constructed a load member that was mounted within the frame of a rigid 200-kip servohydraulic, closed-loop test system to hold the VAWT section and permit cantilever bending along the shear centerline of the beam. A computer program was developed to synthesize a narrow band, pseudo-random load history with fixed root mean square (RMS) stress levels at a given bandwidth and central frequency. Six specimens each of two different weld configurations at the flange mounting plate were tested at several RMS stress levels with failure defined as visual observation of a 3-inch-long crack in the VAWT. In order to test at as great a frequency as possible, a 20-kip hydraulic ram with a 10-GPM servovalve was employed ...

Energy Technology Data Exchange (ETDEWEB)

Background: the authors report on the conception and first clinical application of a donut-shaped high-dose configuration for proton therapy (PT). This approach allows one to intensify target volume dose coverage for targets encompassing a critical, dose-limiting structure - like here, the cauda equina -, whilst delivering minimal dose to other healthy structures surrounding the target, thereby reducing the integral dose. Methods and results: intensity-modulated PT methods (IMPT) for spot scanning were applied to create and deliver a donut-shaped high-dose configuration with protons, allowing treating > 75% of the target with at least 95% of the prescribed dose of 72.8 CGE, whilst restricting dose to the cauda equina to 60-65 CGE. Integral dose was lower by a factor of 3.3 as compared to intensity-modulated radiotherapy with photons (IMXT). Conclusion: IMPT and spot scanning technology allow a potentially clinically useful approach which ...

Energy Technology Data Exchange (ETDEWEB)

The objective of our research was to obtain fundamental information regarding the functional dependence of the diffusion coefficient of coal molecules on the ratio of molecule to pore diameter. That is, the objective of our study was to examine the effect of molecule size and configuration on hindered diffusion of coal macromolecules through as porous medium. To best accomplish this task, we circumvented the complexities of an actual porous catalyst by using a well defined porous matrix with uniform capillaric pores, i.e., a track-etched membrane. In this way, useful information was obtained regarding the relationship of molecular size and configuration on the diffusion rate of coal derived macromolecules through a pore structure with known geometry. Similar studies were performed using a pellet formed of porous alumina, to provide a link between the idealized membranes and the actual complex pore structure of real catalyst extrudates. The ...

Energy Technology Data Exchange (ETDEWEB)

The flow distribution through a plate-fin heat exchanger is studied by using a computational fluid dynamics (CFD) code, FLUENT. The flow distribution through any heat exchanger affects its performance. In designing a heat exchanger, it is assumed that the fluid is uniformly distributed through the heat exchanger core. In practice, however, it is impossible to distribute fluid uniformly, because of an improper inlet configuration, imperfect design, and a complex heat transfer process. The CFD simulation of the flow distribution in the header of a conventional plate-fin heat exchanger is presented. It is found that the flow maldistribution is very serious in the y-direction of the header. A modified header is proposed and simulated using CFD. The modified header configuration has a more uniform flow distribution than the conventional header configuration. Hence, the efficiency of the modified heat exchanger is seen to be ...

Science.gov (United States)

The major purpose of the work described in this report was to use diffusion modeling techniques to calculate the impact on ambient air quality of SO2 emissions from the ASARCO copper smelter in Tacoma, Washington for the existing smelter configuration (51-percent constant emissions control) and for 20 alternative smelter configurations with varying degrees of constant emissions control. The accuracy of the modeling techniques was established by the close correspondence obtained between calculated and observed short-term ground-level SO2 concentrations for 20 selected historical cases, when high hourly SO2 concentrations were measured in the area surrounding the smelter, as well as by the close agreement between calculated and observed annual average concentrations for 1972. The results of the model calculations show that the maximum allowable constant SO2 emission rate consistent with maintaining the Washington Department of Ecology (DOE) and ...

Energy Technology Data Exchange (ETDEWEB)

The aim of this work is to be able to describe transformations, occurring when solids and gases are in non isothermal and non isobaric conditions, with kinetic models. A methodology has been used. Two essential processes have to be taken into account: the germination and the growth. The germs are supposed to be formed (at constant temperature and pressure) in the grains surface with a constant velocity by surface unit, (gamma), called germination surface frequency (number of germs.m{sup -2}.s{sup -1}. The growth velocity is characterized by a growth surface reactivity, (phi) (in mol.m{sup -2}.s{sup -1}). With an appropriate transformation model, it is possible to obtain the variations of (gamma) and (phi) in terms of the temperature and pressure which are then used in the calculation of the velocity in non isothermal and non isobaric conditions. In order to validate the developed method, two reactions have been studied. For the first one, the kaolinite ...

International Nuclear Information System (INIS)

Optimal design of the hyperfractionated radiotherapy requires basic radiobiological data such as the critical dose per fraction, number of fractions per day and total equivalent dose, to name a few. As a prelude to in vivo hyperfractionated irradiation, the authors carried out experiments to determine quantitative changes in the proliferation and cell kinetic parameters of multicellular spheroids after hyperfractionated irradiation. Experiments were carried out with HeLa S-3 spheroid growing in MEM culture media. Hyperfractionated irradiation schedules were 1.5 Gy/f, 2f/day and 1.0 Gy/f, 3 f/day. At intervals after irradiation, cell numbers, growth delays and cell cycle distribution of spheroids were determined. The kinetic data were obtained by the use of flow cytometry. The most pronounced changes in cell kinetic parameters were early G/sub 2/M block, proportional to single radiation dose up to 4.0 Gy. There was a ...

Energy Technology Data Exchange (ETDEWEB)

The objective of the current MITRE study is to estimate the cost of the coal derived liquid products that result from processing low rank coals in the Wilsonville and HRI CTSL configurations. The resultant cost of liquids is then compared to liquids produced from bituminous coals. The methodology used to accomplish the above objective was to utilize the MITRE coal liquefaction cost model to assess the overall technical and economic performance of low rank coals in both the Wilsonville and HRI configurations. Actual test data from Wilsonville and HRI was used as the basis for these analyses. This test data is modified to simulate complete resid recycle extinction and to standardize the operating performance of the deashing unit. This corrected yield data is then used in the simulation models to predict the overall performance and economics of a conceptual commercial coal liquefaction facility. 9 refs., 7 figs.

Energy Technology Data Exchange (ETDEWEB)

The Recycler ring magnet will be made of Strontium ferrite permanent magnets. A strontium ferrite permanent magnet without compensation has a temperature coefficient of -0.2 % in dB/dT. To compensate this effect, we are utilizing 30 % Ni 70 % Fe alloy, a temperature compensation ferromagnetic material with a low Curie point. To search for optimum commercially available material and optimum condition, we made a couple of simple model magnets, and tested with several different compensating material. The test results are reported and its optimal conditions are shown. Several different configurations were tested including a possible 2 kG magnet configuration.

Energy Technology Data Exchange (ETDEWEB)

In this paper the basic properties of non-rotating and slowly rotating protoneutron stars in the relativistic mean-field approach are discussed. The equation of state is the main input to the structure equations. The TM1 parameter set extended to the finite-temperature case is used to obtain the mass-radius relation for protoneutron stars. The occurrence of unstable branches in the mass-radius relation are presented. This allows for the existence of distinctively different evolution tracks for protoneutron stars. The low-density protoneutron star configurations are estimated. The stable configurations obtained for fixed lepton number Y{sub L}=0.4 are compared with those obtained for fixed proton fraction Y{sub P}=0.1776. (author)

British Library Electronic Table of Contents (United Kingdom)

The present investigation focuses on the study of design parameters for a generic fan-in-wing configuration. The objective is to evaluate the performance of a fan-in-wing concept in a Short-Take-Off and Landing situation. The results presented are also of interest for transition between hover and a wing-sustained flight for a Vertical Take Off and Landing concept. Steady Reynolds Averaged Navier-Stokes computations using an actuator disk technique are performed. The results show a good agreement with experimental data and simulation results obtained in previous investigations for a generic wind tunnel model. A parametric study is conducted for a more realistic wing planform. For a single fan installed in the wing, the streamwise and spanwise influence on the wing aerodynamics is studied. I...

Energy Technology Data Exchange (ETDEWEB)

The high repetition rate and low single-pass gain inherent in an rf-driven Free Electron Laser (FEL) dictate that the laser system be configured as an oscillator. This allows the laser's electric field to build up over many passes around a high Q cavity. By way of contrast, the high-current capability of the Induction Linac (IL) system permits high single-pass optical gain, but the relatively low duty factor precludes oscillator operation; the pulses are neither long enough nor often enough to permit a field to accumulate in a cavity. The IL is thus configured as a MOPA (master oscillator/power amplifier) with a conventional laser serving as the MO. This report concentrates on the status of IL-driven FEL research at LLNL and gives a description of several applications for the high-peak-power radiation produced by an induction linac FEL.

CERN Document Server

An analysis of the cross section for hadronic production of gluino-squark pairs close to threshold is presented. Within the framework of non-relativistic QCD a significant enhancement compared to fixed order perturbation theory is observed which originates from the characteristic remnants of the gluino-squark resonances below the nominal pair threshold. The analysis includes all colour configurations of S-wave gluino-squark pairs, i.e. triplet, sextet and 15 representation. Matching coefficients at leading order are separately evaluated for all colour configurations. The dominant QCD corrections, arising from initial- and final-state radiation are included. The non-relativistic dynamics of the gluino pair is solved by calculating the Green's function in Next-to-Leading Order (NLO). The results are applied to benchmark scenarios, based on Snowmass Points and Slopes (SPS). As a consequence of the large decay rate of at least one of the ...

International Nuclear Information System (INIS)

Since the advent of the first free electron laser (FEL) in 1976 up to now, a series of principles, configurations and operation modes of these FELs have been devised and partially implemented. The principles refer to transverse FEL, longitudinal FEL, combined FEL, and transverse optical klystron FEL. Configurations may be standard or many-stage and the undulators may be magnetostatic, electrostatic or electromagnetic. The operation regimes may be low-gain Compton type, high-gain Compton type, Raman type, with and without space charge. The operation modes may be the amplification of an external coherent EM radiation, a self-amplified spontaneous emission (SASE), or an oscillator. The paper presents in detail these concepts and the limit between classical approach and the quantum approach of FEL. (Author).

Energy Technology Data Exchange (ETDEWEB)

A focused ion beam (FIB) system produces a final beam spot size down to 0.1 {mu}m or less and an ion beam output current on the order of microamps. The FIB system increases ion source brightness by properly configuring the first (plasma) and second (extraction) electrodes. The first electrode is configured to have a high aperture diameter to electrode thickness aspect ratio. Additional accelerator and focusing electrodes are used to produce the final beam. As few as five electrodes can be used, providing a very compact FIB system with a length down to only 20 mm. Multibeamlet arrangements with a single ion source can be produced to increase throughput. The FIB system can be used for nanolithography and doping applications for fabrication of semiconductor devices with minimum feature sizes of 0.1 m or less. 13 figs.

British Library Electronic Table of Contents (United Kingdom)

Timely detection of the pneumatic system problems is important in industry. Many techniques have been employed to solve this problem. In this paper, Genetic Algorithm (GA) based optimal configuration of neural networks is proposed for fault diagnostic of bottle filling systems. Back-propagation is used for neural networks algorithm. The back-propagation algorithm had six inputs and one output. A fitness function was designed to the minimize execution time of ANN model by keeping the number of hidden layer(s) and nodes as low as possible while the mean square error of estimated output error is minimized. The designed GA-ANN combination and the graphical user interface (GUI) eliminate the trial and error process for selection of the fastest and most accurate configuration. The performance of...

Energy Technology Data Exchange (ETDEWEB)

The intrinsic energy levels in the doubly odd isotopes of Np with mass number 238 and of Am with mass numbers 240, 242 and 244 are calculated using the zero-range neutron-proton residual interaction whose parameters are evaluated using the atomic masses and the ground state Gallagher-Moszkowski splitting energy in each case. A configuration dependence of the residual interaction is in evidence in several cases. The results are compared with the experimental data and the comparison is used to check on the two-particle configuration assignments to the intrinsic states in the respective spectra. Encouraged by the nature and the degree of the agreement of the theory with the available experimental data, predictions are made about the expected location of the as yet unobserved two-quasiparticle states in these nuclei.

Energy Technology Data Exchange (ETDEWEB)

The drift-kink instability in field-reversed configurations with a beam component is investigated by means of a three-dimensional particle simulation. The unstable mode with the toroidal mode number n=4 grows with the rate {gamma} {approx} 0.1 - 1.0{omega}{sub ci} for a strong beam current and deforms the plasma profile along the beam orbit in the vicinity of the field-null line. This mode is nonlinearly saturated as a result of the relaxation of current profile. Both the saturation level and the growth rate tend to increase as the ratio of the beam current to the plasma current I{sub b}/I{sub p} increases. It is also found that there is a threshold value of the beam velocity {upsilon}{sub b} {approx} {upsilon}{sub Ti} (ion thermal velocity) for the excitation of the instability. (author)

Energy Technology Data Exchange (ETDEWEB)

Evaluating the need for remedial cleanup at a waste site involves both finding the average contaminant concentration and identifying highly contaminated areas, or hot spots. A nomographic procedure to determine the sample configuration needed to locate a hot spot is presented. The technique can be used to develop a waste-site sampling plant - to determine either the grid spacing required to detect a hot spot at a given level of confidence, or the probability of finding a hot spot of a certain size, given a particular grid spacing. The method and computer program (ELIPGRID) were developed for locating geologic deposits, but the basic procedure can also be used to detect hot spots at chemical- or nuclear-waste disposal sites. Nomographs based on the original program are presented for three sampling-grid configurations - square, rectangular and triangular.

CERN Document Server

{The determination of cluster masses is a complex problem that would be aided by information about the cluster shape and orientation (along the line-of-sight).} {It is in this context, that we have developed a scheme for identifying the intrinsic morphology and inclination of a cluster, by looking for the signature of the true cluster characteristics in the inter-comparison of the different deprojected emissivity profiles (that all project to the same X-ray brightness distribution) and by using SZe data when available.} {We deproject the cluster X-ray surface brightness profile under the assumptions of four different geometry and inclination configurations for the observed system; these 4 configurations correspond to four extreme geometry+inclination scenarios. The deprojection in question is performed by the non-parametric algorithm DOPING. The formalism is tested with model systems and then is applied to a sample of 24 clusters. While the ...

International Nuclear Information System (INIS)

The electronic structures of URh_3, UPd_3, UPt_3 and UAu_3 are calculated with the self-interaction-corrected local-spin-density approximation. We find that only in URh_3 the f-electrons are fully delocalized. UPt_3 has one f-electron localized at each U site, whilst a localized f"2 configuration of the U-ion is found for UPd_3. It is predicted that upon application of pressure, UPd_3 will acquire the f"1 configuration and possibly exhibit heavy-fermion behaviour. We find that UAu_3 is characterized by the same mixed localized-delocalized f-electron manifold as UPd_3. (author)

Energy Technology Data Exchange (ETDEWEB)

This paper reports that the point defect model for steady-state passive films formed anodically on metal s in aqueous environments has been extended to include irreversible dissolution of the film and the irreversible generation and annihilation of cation and oxygen vacancies at the metal/film and film/solution interfaces. THe model yields a number of diagnostic criteria that can be used to identify the majority (vacancy) charge carrier and to characterize the kinetic nature of the interfacial vacancy generation and annihilation processes. We use these criteria to show that the steady-state passive film that forms on nickel in acidic phosphate buffer solutions is a cation conductor and that cation transport from the metal to the solution involves irreversible ejection of cations from the film. On the other hand, the passive film that forms on tungsten in the same environment under steady-state conditions is found to be an oxygen ion conductor with the passive ...

CERN Document Server

In dissipative ordinary differential equation systems different time scales cause anisotropic phase volume contraction along solution trajectories. Model reduction methods exploit this for simplifying chemical kinetics via a time scale separation into fast and slow modes. The aim is to approximate the system dynamics with a dimension-reduced model after eliminating the fast modes by enslaving them to the slow ones via computation of a slow attracting manifold. We present a novel method for computing approximations of such manifolds using trajectory-based optimization. We discuss Riemannian geometry concepts as a basis for suitable optimization criteria characterizing trajectories near slow attracting manifolds and thus provide insight into fundamental geometric properties of multiple time scale chemical kinetics. The optimization criteria correspond to a suitable mathematical formulation of "minimal relaxation" of chemical forces along reaction ...

Energy Technology Data Exchange (ETDEWEB)

A detailed kinetic study of the epoxidation of 1-octene with hydrogen peroxide catalyzed by Pt(II) complexes is reported. The two systems analyzed were (diphoe)Pt(CF/sub 3/)(OH)/1-octene/H/sub 2/O/sub 2//THF and ((diphoe)Pt(CF/sub 3/)(CH/sub 2/Cl/sub 2/))BF/sub 4//1-octene/H/sub 2/O/sub 2//H/sub 2/O/CH/sub 2/Cl/sub 2/. Rate data were determined with GLC from epoxide formed vs time plots. Evidence for many of the organometallic intermediates and the individual steps involved was gained from IR studies, /sup 19/F NMR studies, and especially designed experiments including studies of the acidity effect. In both cases the kinetic analysis suggests a mechanism in which the actual oxidant is a PtOOH species that interacts with a Pt-olefin complex in the oxygen-transfer step (second-order dependence on platinum). 29 references, 12 figures, 3 tables.

Energy Technology Data Exchange (ETDEWEB)

The biosorption of Cu(II) from aqueous solutions by valonia tannin resin was investigated as a function of particle size, initial pH, contact time and initial metal ion concentration. The aim of this study was to understand the mechanisms that govern copper removal and find a suitable equilibrium isotherm and kinetic model for the copper removal in a batch reactor. The experimental isotherm data were analysed using the Langmuir, Freundlich and Temkin equations. The equilibrium data fit well in the Langmuir isotherm. The experimental data were analysed using four sorption kinetic models - the pseudo-first- and second-order equations, the Elovich and the intraparticle diffusion model equation - to determine the best fit equation for the biosorption of copper ions onto valonia tannin resin. Results show that the pseudo-second-order equation provides the best correlation for the biosorption process, whereas the Elovich equation also fits the ...

Energy Technology Data Exchange (ETDEWEB)

This paper describes the development of a computational multiphase fluid dynamics (CMFD) model of the Fischer Tropsch (FT) process in a Slurry Bubble Column Reactor (SBCR). The CMFD model is fundamentally based which allows it to be applied to different industrial processes and reactor geometries. The NPHASE CMFD solver [1] is used as the robust computational platform. Results from the CMFD model include gas distribution, species concentration profiles, and local temperatures within the SBCR. This type of model can provide valuable information for process design, operations and troubleshooting of FT plants. An ensemble-averaged, turbulent, multi-fluid solution algorithm for the multiphase, reacting flow with heat transfer was employed. Mechanistic models applicable to churn turbulent flow have been developed to provide a fundamentally based closure set for the equations. In this four-field model formulation, two of the fields are used to track the gas phase (i.e., small spherical and ...

International Nuclear Information System (INIS)

Hydrolysis kinetics of the lead silicate glass (LSG) with 40 mol% PbO in 0.5 N HNO_3 aqueous acid solution was investigated. The surface morphology and the gel layer thickness were studied by scanning electron microscopy (SEM) micrographs. Energy dispersive X-ray spectroscopy (EDS) and inductively coupled plasma spectroscopy (ICP) were used to determine the composition of the gel layer and the aqueous solution, respectively. The silicon content of the dissolution products was determined by using weight-loss data and compositions of the gel layer and the solution. The kinetic parameters were determined using the shrinking-core-model (SCM) for rate controlling step. The activation energy obtained for hydrolysis reaction was Q_c_h_e = 56.07 kJ/mole. The diffusion coefficient of the Pb ions from the gel layer was determined by using its concentration in solution and in LSG. The shrinkage of the sample and the gel layer thickness during dissolution ...

British Library Electronic Table of Contents (United Kingdom)

Biosorption of lead(II) ions from aqueous solution onto the seed husk of Calophyllum inophyllum was investigated in a batch system. Equilibrium, thermodynamics and kinetic studies were conducted by considering the effects of pH, initial metal ion concentration, contact time, and temperature. The results showed that the uptake of the metal ions increased with increase in initial metal ion concentration. The pH for optimum adsorption was 4 for the Pb(II) ions (q=4.86mg/g and 97.2% adsorption). Langmuir isotherm described the biosorption of Pb(II) ions onto the biomass (R^2=0.9531) better than the Freundlich model (R^2=0.7984), and the Temkin model (R^2=0.8761). Biosorption kinetics data obtained for the metal ions sorption were fitted using pseudo-first-order and pseudo-second-order. It was ...

Energy Technology Data Exchange (ETDEWEB)

The sequence of nitride formation during the early stages of plasma nitriding of pure iron was studied by optical microscopy, SEM, TEM and x-ray diffraction. Plasma nitriding at {approximately}490 C in a 25 vol.%H{sub 2} + 75 vol.%N{sub 2} mixture starts with the formation of {gamma}{prime}-Fe{sub 4}N after 40s. Once {gamma}{prime} nucleates, it mainly spreads laterally due to diffusion shortcuts in the discontinuous surface nitride layer. Before {gamma}{prime} is continuous on the surface, {epsilon} nucleates on top of it shortly after 40S. Epsilon is then observed to grow, both inwardly and laterally along with {gamma}{prime}. A compact {gamma}{prime}/{epsilon} bilayer forms on the surface at around 100s. The kinetics of nucleation, growth and compactation of the nitrides observed in the present work was significantly more rapid than in any of the nitriding process reported in the literature, including plasma nitriding. The acceleration of the nitriding ...

Energy Technology Data Exchange (ETDEWEB)

Trichloroethene (TCE), a common groundwater contaminant, can be degraded under certain conditions by microorganisms that occur naturally in the subsurface. TCE can be degraded under anaerobic conditions to less chlorinated compounds and ultimately into the non-chlorinated, non-hazardous end product, ethene, via anaerobic reductive dechlorination (ARD). ARD is widely recognized as a TCE degradation mechanism, and occurs in active groundwater remediation and can occur during monitored natural attenuation (MNA). MNA relies on natural processes, such as dispersion and degradation, to reduce contaminant concentrations to acceptable levels without active human intervention other than monitoring. TCE can also be biodegraded under aerobic conditions via cometabolism, in which microbial enzymes produced for other purposes fortuitously also react with TCE. In cometabolism, TCE is oxidized directly to non-hazardous products. Cometabolism as a TCE-degrading process under aerobic conditions is less ...

Energy Technology Data Exchange (ETDEWEB)

This study focused on the biosorption of total chromium onto red algae (Ceramium virgatum) biomass from aqueous solution. Experimental parameters affecting biosorption process such as pH, contact time, biomass dosage and temperature were studied. Langmuir, Freundlich and Dubinin-Radushkevich (D-R) models were applied to describe the biosorption isotherms. Langmuir model fitted the equilibrium data better than the Freundlich isotherm. The biosorption capacity of C. virgatum biomass for total chromium was found to be 26.5 mg/g at pH 1.5 and 10 g/L biomass dosage, 90 min equilibrium time and 20 deg. C. From the D-R isotherm model, the mean free energy was calculated as 9.7 kJ/mol, indicating that the biosorption of total chromium was taken place by chemisorption. The calculated thermodynamic parameters ({delta}G{sup o}, {delta}H{sup o}and {delta}S{sup o}) showed that the biosorption of total chromium onto C. virgatum biomass was feasible, spontaneous and exothermic at 20-50 deg. C. ...

Energy Technology Data Exchange (ETDEWEB)

The kinetics of {sup 14}C-photosynthate import by developing wheat grains was followed after pulse-labeling the flag leaf with {sup 14}CO{sub 2}. Samples were collected from four successive points along the transport pathway to and within the grain: exuding aphid stylets on the peduncle, exuding grain pedicels, the grain crease tissues, and the liquid contents of the endosperm cavity. In addition, microautoradiographs were prepared of the grain crease tissues during movement of the {sup 14}C pulse into the grain. At all times, sucrose accounted for 93 to 97% of the total {sup 14}C present at all four sampling sites. The main features of the {sup 14}C kinetics could be accounted for by a simple compartmental model consisting of sucrose pools in series. Microautoradiographs of the crease tissues showed fairly uniform labeling of vascular parenchyma at all times, with a sharp gradient in labeling across the chalaza to the nucellus. Thus the ...

International Nuclear Information System (INIS)

We have investigated the microstructure evolutions in the Ti17 near #beta# titanium alloy during heat treatments. The phase transformation has first been studied experimentally by combining X-ray diffraction analysis, electrical resistivity and microscopy observations. From a series of isothermal treatments, a IT diagram has been determined, which takes into account the different morphologies. Then, a Johnson-Mehl-Avrami-Kolmogorov (JMAK) model has been successfully used to describe the phase transformation kinetics during either isothermal or cooling treatments. Finally, the coupling of the JMAK model to the finite element software ZeBuLoN allowed us to investigate the evolution of the spatial distribution of the different morphologies during the cooling of an aircraft engine shaft disk after forging.

British Library Electronic Table of Contents (United Kingdom)

The oxidation of n-butylbenzene was studied in a jet-stirred reactor (JSR) at 10atm in dilute conditions providing new experimental results over the low- and high-temperature range 550-1180K, and variable equivalence ratio (0.25ϕ1.5). They consisted of concentration profiles of the reactants, stable intermediates and final products, measured as a function of temperature, at a constant residence time of 1s, by sonic probe sampling followed by on-line GC-MS and off-line GC-TCD-FID and GC-MS analyses. The oxidation of n-butylbenzene in these conditions was modeled using a detailed chemical kinetic reaction mechanism (404 species and 2210 reactions, most of them reversible) deriving from a previous scheme proposed for the ignition, oxidation, and combustion of simple aromatics (benzene,...

CERN Document Server

We study the dynamics of states perturbatively expanded about a harmonic system of loop quantum cosmology, exhibiting a bounce. In particular, the evolution equations for the first and second order moments of the system are analyzed. These moments back-react on the trajectories of the expectation values of the state and hence alter the energy density at the bounce. This analysis is performed for isotropic loop quantum cosmology coupled to a scalar field with a small but non-zero constant potential, hence in a regime in which the kinetic energy of matter dominates. Analytic restrictions on the existence of dynamical coherent states and the meaning of semi-classicality within these systems are discussed. A numerical investigation of the trajectories of states that remain semi-classical across the bounce demonstrates that, at least for such states, the bounce persists and that its properties are similar to the standard case, in which the moments of the states are ...

British Library Electronic Table of Contents (United Kingdom)

The non-isothermal pyrolysis kinetics of Acetocell (the organosolv) and Lignoboost (kraft) lignins, in an inert atmosphere, have been studied by thermogravimetric analysis. Using isoconversional analysis, it was concluded that the apparent activation energy for all lignins strongly depends on conversion, showing that the pyrolysis of lignins is not a single chemical process. It was identified that the pyrolysis process of Acetocell and Lignoboost lignin takes place over three reaction steps, which was confirmed by appearance of the corresponding isokinetic relationships (IKR). It was found that major pyrolysis stage of both lignins is characterized by stilbene pyrolysis reactions, which were subsequently followed by decomposition reactions of products derived from the stilbene pyrolytic pr...

British Library Electronic Table of Contents (United Kingdom)

The condensation reaction of furfural (F) on acetone (Ac) gives a high added value product, the 4-(2-furyl)-3-buten-2-one (FAc), used as aroma in alcohol free drinks, ice, candies, gelatines and other products of current life. This synthesis valorises the residues of sugar cane treatment since furfural is obtained by hydrolysis of sugar cane bagasse followed by vapor training extraction. In the face of numerous and complex reactions involved in this synthesis, it is very complicated to define the kinetic laws from exact stoichiometry. A solution allowing to cope the problem consists in identifying an appropriate stoichiometric model. It does not attempt to represent exactly all the reaction mechanisms, but proposes a mathematical support to integrate available knowledge on the transformati...

British Library Electronic Table of Contents (United Kingdom)

A numerical model is developed to study electrolyte dependent kinetics in fuel cells. The model is based on the Poisson-Nernst-Planck (PNP) and generalized-Frumkin-Butler-Volmer (gFBV) equations, and is used to understand how the diffuse layer and ionic transport play a role in the performance difference between acidic and alkaline systems. The laminar flow fuel cell (LFFC) is used as the model fuel cell architecture to allow for the appropriate comparison of equivalent acidic and alkaline systems. We study the overall cell performance and individual electrode polarizations of acidic and alkaline fuel cells for both balanced and unbalanced electrode kinetics as well as in the presence of transport limitations. The results predict cell behavior based on electrolyte composition that strongly...

British Library Electronic Table of Contents (United Kingdom)

The lignin, one of the main by-products of the pulp industry, can be used to remove dyes from textile wastewaters. The potential of the lignin for Brilliant Red HE-3B reactive dye removal from aqueous solutions at pH=1.5 was examined by the batch technique as a function of dye concentration, solution temperature and contact time. The Freundlich, Langmuir, Dubinin-Radushkevich and Tempkin adsorption isotherms were used to describe the data of sorption equilibrium and to determine its corresponding isotherm constants. The thermodynamic parameters DG, DH and DS were also determined; the obtained values show that the sorption of reactive dye on lignin is a spontaneous, endothermic and entropy-driven process. The kinetic of reactive dye sorption was analyzed using the pseudo-first order and pse...

Energy Technology Data Exchange (ETDEWEB)

The transformation from the as-quenched amorphous to the crystalline state in Fe/sub 78/B/sub 13/Si/sub 9/ alloy has been investigated using a new-type neutron diffractometer. The time resolved diffraction patterns clearly show that this alloy crystallizes into FeSi alloy and Fe/sub 2/B in that order. The time evolution of these crystalline phases can be analyzed by the Kolmogorov-Johnson-Mehl-Avrami equation with the exponent of about 2.5 over a wide temperature range. This suggests that the crystallization occurs by the diffusion-controlled growth with a constant nucleation rate. The scaling behavior in the crystallization kinetics is also discussed.

British Library Electronic Table of Contents (United Kingdom)

Using a novel, pulsed micro-second time-resolved photoacoustic (PA) instrument, we measured thermal dissipation and energy storage (ES) in the intact cells of wild type (WT) Chlamydomonas reinhardtii, and mutants lacking either PSI or PSII reaction centers (RCs). On this time scale, the kinetic contributions of the thermal expansion component due to heat dissipation of absorbed energy and the negative volume change due to electrostriction induced by charge separation in each of the photosystems could be readily distinguished. Kinetic analysis revealed that PSI and PSII RCs exhibit strikingly different PA signals where PSI is characterized by a strong electrostriction signal and a weak thermal expansion component while PSII has a small electrostriction component and large thermal expansion....

Energy Technology Data Exchange (ETDEWEB)

A non-dissipative drift kinetic simulation scheme, which rigorously satisfies the time-reversibility, is applied to the three-mode coupling problem of the ion temperature gradient (ITG) instability. It is found from the simulation that the three-mode ITG system repeats growth and decay with a period which shows a logarithmic divergence for infinitesimal initial perturbations. Accordingly, time average of the mode amplitude vanishes, as the initial amplitude approaches to zero. An exact solution is analytically given for a class of initial conditions. An excellent agreement is confirmed between the analytical solution and numerical results. The results obtained here provide a useful reference for basic benchmarking of theories and simulation of the ITG modes. (author)

Energy Technology Data Exchange (ETDEWEB)

The kinetics of the reaction of 2,4-dinitrohalogenobenzenes (chlorine, bromine, and iodine derivatives) with tetraethylammonium azide in acetonitrile and in a mixed acetonitrile-dioxane solvent (80 vol. % dioxane) were studied. It was established that there is a marked increase (by more than three orders of magnitude) in the azidization rate constant in the transition from protic solvents to aprotic media, due to the decrease in the activation energy barrier of the reaction. The nucleophilicity parameters N/sup +/ for the azide ion in the investigated solvents were determined in terms of Ritchie's relationship. It was established that the effect of the nature of the leaving group on the rate constant of the reactions is complex in character, and it was shown that treatment of the relative reactivity series for the investigated substrates must be based on an analysis of the activation parameters and not restricted to data obtained at only one temperature.

Energy Technology Data Exchange (ETDEWEB)

One third of the microstructure of glassy carbon (GC) consists of closed pores. Density measurements indicate that the total pore volume depends only on the heat treatment temperature and not on the heat treatment time, a characteristic of coarsening. The kinetics of coarsening of these pores on heat treatment has been investigated by analyzing the changes in specific surface area of the pores as determined by the small angle X-ray scattering (SAXS) technique. A part of the surface area change is due to thermal expansion induced microcracking. Both the superposition method after correcting the thermal expansion induced surface area change and the curve fitting method give an activation energy of 64 +/- 10 kcal/mole. This value is compared with the activation energies of various rate processes in graphite. A model of coarsening of the pores based on a vacancy migration mechanism is proposed.

Energy Technology Data Exchange (ETDEWEB)

Poly(ethylene terephthalate) (PET) powder from waste bottles was degraded at atmospheric pressure in 7--13 M nitric acid at 70--100 C for 72 h, to clarify the mechanism of a feed stock recycling process. Terephthalic acid (TPA) and ethylene glycol (EG) were produced by the acid-catalyzed heterogeneous hydrolysis of PET in nitric acid, and the resulting EG was simultaneously oxidized to oxalic acid. The kinetics of the hydrolysis of PET in nitric acid could be explained by a modified shrinking core model of chemical reaction control, in which the effective surface area is proportional to the degree of unreacted PET, affected by the deposition of the product TPA. The apparent rate constant was inversely proportional to particle size and to the concentration of the nitric acid. The activation energy of the reaction was 101.3 kJ/mol.

Science.gov (United States)

A novel wastewater treatment technique has been investigated, for reactive dye removal, in batch kinetic systems. These experimental studies have indicated that charred dolomite has the potential to act as an adsorbent for the removal of Brilliant Red reactive dye from aqueous solution. The effect of initial dye concentration, adsorbent mass:liquid volume ratio, and agitation speed on dye removal have been determined with the experimental data mathematically described using empirical external mass transfer and intra-particle diffusion models. The experimental data show conformity with an adsorption process, with the removal rate heavily dependent on both external mass transfer and intra-particle diffusion. PMID:12691893

Energy Technology Data Exchange (ETDEWEB)

A study was made of the kinetics of L-(/sup 3/H)quinuclidinyl benzilate binding with membrane-bound muscarine cholinoreceptors from the rat brain. Determination was made of the rate constants of this process, and constants as a function of ligand concentration was investigated, indicating that there is a complex mechanism of interaction of antagonists with muscarine receptor. With up to 3.5 nM concentrations of L-(/sup 3/H)quinuclidinyl benzilate, the binding reaction occurs in two stages: rapid equilibrated binding is followed by a slow process of conformational isomerization of the receptor-ligand complex. At higher ligand concentrations, there is additional drastic increase in constant of rate of ligand binding a new plateau is reached. Such dependence of rate constant on ligand concentration is indicative of the cooperative nature of interaction between antagonists and muscarine receptors. This is possible if there are in the receptor complex several binding ...

CERN Document Server

The finite element method and dimensional analysis have been applied in the present paper to study a hydraulic impact, which is utilized in a non-explosive rock breaking technology in mining industry. The impact process of a high speed piston on liquid water, previously introduced in a borehole drilled in rock, is numerically simulated. The research is focused on the influences of all the parameters involved in the technology on the largest principal stress in the rock, which is considered as one of the key factors to break the rock. Our detailed parametric investigation reveals that the variation of the isotropic rock material properties, especially its density, has no significant influence on the largest principal stress. The influences of the depth of the hole and the depth of the water column are also very small. On the other hand, increasing the initial kinetic energy of the piston can dramatically increase the largest principal stress and the best way to ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Hybrid power plants consisting of a solid oxide fuel cell (SOFC) and a gas turbine show high electrical efficiencies, however require pressurisation of the SOFC to several bar. This paper presents a theoretical investigation of the pressure influence on SOFC performance and durability. A two-dimensional elementary kinetic model is used to predict the performance of a single cell in the pressure range of 1-20-bar. The influence of pressure on thermodynamics, reaction kinetics, porous electrode diffusion, channel transport and efficiency is assessed. It was found that polarisation resistance decreases with increasing pressure due to increased diffusion through porous electrodes and a higher electrode surface coverage with reactant species. Furthermore, open-circuit voltage increases...

British Library Electronic Table of Contents (United Kingdom)

The present study was designed with an aim to analyze the effect of acute aluminium phosphide (ALP) exposure (10mg/kg b.wt, intragastrically) on the kinetic characteristics of cytochrome oxidase and energy metabolism in male Wistar rat liver mitochondria. Liver mitochondrial preparations from ALP-treated rats exhibited significant decrease (66%) in the activity of cytochrome oxidase suggesting that there was a decrease in the catalytic efficiency of the active oxidase molecules on ALP treatment. The decreased activity of cytochrome oxidase with altered NADH and succinic dehydrogenase activities might have contributed towards a significant decline in state 3 and state 4 respiration as observed. These alterations in the electron transport chain complexes in turn adversely affected the ATP sy...

International Nuclear Information System (INIS)

Pulse radiolysis studies of the formation kinetics and the yields of various phenylcarbenium ions from several different solutes in 1,2-dichloroethane solution have been carried out. The results indicate that there are two kinetically distinguishable cationic species of the solvent which react selectively with the different solutes to form the phenylcarbenium ions. It is suggested that one is a cation radical (yield 0.68 molecule/100 eV) and the other a carbocation (yield 0.20 molecule/100 eV). Rate constants for their separate reactions with selected aromatic compounds and with ammonia have been determined. Molar extinction coefficients have been estimated for benzyl cation, diphenyl cation radical, and anthracene cation radical. 6 figures, 1 table.

British Library Electronic Table of Contents (United Kingdom)

Iron nanoparticles were produced using extracts of green tea leaves (GT-Fe NPs). The materials were characterized using TEM, SEM/EDX, XPS, XRD, and FTIR techniques and were shown to contain mainly iron oxide and iron oxohydroxide. The obtained nanoparticles were then utilized as a Fenton-like catalyst for decolorization of aqueous solutions containing methylene blue (MB) and methyl orange (MO) dyes. The related experiments investigated the removal kinetics and the effect of concentration for both MB and MO. The concentrations of dyes in aqueous solution were monitored using ultraviolet-visible (UV-vis) spectroscopy. The results indicated fast removal of the dyes with the kinetic data of MB following a second order removal rate, while those of MO were closer to a first order removal rate. T...

CERN Document Server

New non-stationary non-contracted form of the erosive radially-slotted discharge as a thin round sheet with the current of the azimuth direction have been discovered, its existence beings stipulated by a radial transport-wave fluxes. Characteristic features of this discharge is self-confinement of the discharge current magnitude, corresponding decrease of the current pulse duration and occurrence of an energy and substance ejection with rather unusual properties. Measurements of kinetics of the discharge current, the plasma radiation intensity and an electrical probe signal, as well as the transmission electron microscope investigations of characteristic aerodisperse aggregates arising the erosive phase, have been carried out. The probe signal duration was about 10 times greater than that of the current; its kinetics was complicated suggesting existence in the slot of two components with fundamentally different properties and states of the ...

British Library Electronic Table of Contents (United Kingdom)

Abstract In this research, the efficiency of electrocoagulation treatment process using aluminum electrodes to treat synthetic wastewater containing Reactive Red198 (RR198) was studied. The effects of parameters such as voltage, time of reaction, electrode connection mode, initial dye concentration, electrolyte concentration, and inter electrode distance on dye removal efficiency were investigated. In addition, electrical energy consumption, electrode consumption, and operating cost at optimum condition have been investigated. The results showed that dye and chemical oxygen demand removals were 98.6 and 84%, respectively. Electrode consumption, energy consumption and operating cost were 0.052-kg/m3, 1.303-kWh/m3 and 0.256-US$/m3, respectively. Dye removal kinetic followed first order kinet...

Energy Technology Data Exchange (ETDEWEB)

A detailed chemical kinetic model to describe the autoignition of gasoline surrogate fuels is presented consisting of the fuels iso-octane, n-heptane, toluene, diisobutylene and ethanol. Model predictions have been compared with shock tube ignition delay time data for surrogates of gasoline over practical ranges of temperature and pressure, and the model has been found to be sensitive to both changes in temperature and pressure. Moreover, the model can qualitatively predict the observed synergistic and antagonistic non-linear blending behaviour in motor octane number (MON) for different combinations of primary reference fuels (PRFs) and non-PRFs by correlating calculated autoignition delay times from peak pressures and temperatures in the MON test to experimental MON values. The reasons for the blending behaviour are interpreted in terms autoignition chemistry. 37 refs., 11 figs., 4 tabs.

CERN Document Server

We describe a large class of chemical reaction networks, those endowed with a subtle structural property called concordance. We show that the class of concordant networks coincides precisely with the class of networks which, when taken with any weakly monotonic kinetics, invariably give rise to kinetic systems that are injective --- a quality that, among other things, precludes the possibility of switch-like transitions between distinct positive steady states. We also provide persistence characteristics of concordant networks, instability implications of discordance, and consequences of stronger variants of concordance. Some of our results are in the spirit of recent ones by Banaji and Craciun, but here we do not require that every species suffer a degradation reaction. This is especially important in studying biochemical networks, for which it is rare to have all species degrade.