In the paramagnetic region T > 178 K the paramagnetic susceptibility, chi, of Dy was measured as a function of temperature and orientation of the applied magnetic field with respect to the c-axis. For magnetic fields parallel and perpendicular to the c-axis the temperature dependence of chi can be represented by Curie-Weiss laws whereas for arbitrary orientations significant deviations from a Curie-Weiss behaviour were found. The measured anisotropy of the paramagnetic Curie temperatures and of the Curie-Weiss constants is shown to depend mainly on the magnetocrystallineenergy and an anisotropic g-factor. (Auth.).
Magnetic structures and magnetocrystallineanisotropy (MCA) of tetragonal phase Fe_3Pt with an L1_2 atomic ordering in bulk and thin film are investigated by means of the first-principles full-potential linearized augmented plane-wave method. The results obtained predict that the tetragonal phase, in which the tetragonal distortion with (c/a) = 0.95 makes an asymmetry of magnetic properties along the c-axis (out-of-plane) and a-axis (in-plane), has an out-of-plane MCA. In addition, from the thin film calculations, the presence of surface is found to strongly enhance the out-of-plane MCA.
Using the full potential linearized augmented plane wave (FLAPW) method, the magnetic properties of two-dimensional Ru and Rh monolayers (MLs) on a NiAl(001) surface have been investigated. It has been found that free standing one monolayer Ru and Rh films have ferromagnetic ground state with magnetic moments of 2.21 and 1.48 #mu#_B, respectively. The ferromagnetism is still observed even on a Ni terminated NiAl(001) surface, while no magnetic state is found on an Al terminated surface. The calculated magnetic moments of Ru and Rh atoms are 1.56 and 0.88 #mu#_B, respectively. In addition, an induced magnetic moment in surface Ni is observed. It has been found that the free standing Ru film has perpendicular magnetization to the film surface with a magnetocrystallineanisotropy (MCA) energy of 0.66 meV/atom, while an in-plane MCA energy of 0.37 meV/atom is achieved in Rh film. Very interestingly, we find ...
Parameters of permanent magnets result from the combination of intrinsic properties such as saturation magnetization, magnetic exchange, and magnetocrystallineenergy, as well as microstructural parameters such as phase structure, grain size, and orientation. Reduction of grain size into nanocrystalline regime (#approx# 50 nm) leads to the enhanced remanence which derives from ferromagnetic exchange coupling between highly refined grains. In this study the fundamental phenomena, quantities, and structure parameters, which define nanophase permanent magnets are presented and discussed. The theoretical considerations are confronted with experimental data for nanocrystalline Sm-Fe-N type permanent magnets. (author)
This review of methods and designs of transducers for nondestructive determination of the magnitude and nature of the anisotropy of magnetic properties (permeability, induction, coercive force, energy loss due to magnetization reversal) in local portions of ferromagnetic sheet and, in some cases, in individual parts of products. The need to measure the anisotropy is considered for two angles: for the case when the anisotropy is due to the crystallographic texture and determines the main operating characteristics of widely used sheet such as electrical steel and automobile body sheet, and for crystallographically isotropic materials, in which the anisotropy of magnetic properties as a result of mechanical stresses is a measure for determining the internal stresses.
Careful measurements do not confirm an anomalous anisotropy in the angular distribution of fission fragments from the fast neutron fission of Americium 242. The energy range covered was 1.60-3.15 MeV. (AIP)
When searching for anisotropies in the arrival directions of Ultra High Energy Cosmic Rays, one must estimate the number of events expected in each direction of the sky in the case of a perfect isotropy. We present in this article a new method, developed for the Auger Observatory, based on a smooth estimate of the zenith angle distribution obtained from the data itself (which is essentially unchanged in the case of the presence of a large scale anisotropy pattern). We also study the sensitivity of several methods to detect large-scale anisotropies in the cosmic ray arrival direction distribution : Rayleigh analysis, dipole fitting and angular power spectrum estimation.
Fe_5_0Pt_5_0 nanodots dispersed in a SiO_2 film (Fe_5_0Pt_5_0 nanodot film) were formed by a self-assembled nanodot deposition (SAND) method in which Fe_5_0Pt_5_0 and SiO_2 are cosputtered in a high vacuum rf magnetron sputtering equipment. Fe_5_0Pt_5_0 pellets are laid on a SiO_2 target in a sputtering chamber to form the Fe_5_0Pt_5_0 nanodot film in the SAND method. The size and density of Fe_5_0Pt_5_0 nanodot were controlled by changing the ratio of the total area of Fe_5_0Pt_5_0 pellets to that of SiO_2 target. The Fe_5_0Pt_5_0 nanodot size decreases and its density increases when the ratio decreases. As-deposited Fe_5_0Pt_5_0 nanodots self-assembled to a face-centered-cubic phase of single-crystal structure. The Fe_5_0Pt_5_0 nanodot films were annealed to evaluate the nanodot size controllability, the magnetic anisotropy, and the thermal stability. Fully ordered L1_0 face-centered-tetragonal Fe_5_0Pt_5_0 nanodots with high ...
Within the framework of the Bianchi type-IX homogeneous space, we set up a system of coupled equations for the cosmic scale factors, scalar field, and radiative energy density. At the tree level, the equations are written in a self-consistent, Hartree-Fock form. For phi/sup 4/ theory, the system of nine first-order differential equations is solved numerically for a varying ratio of the energy of anisotropy to the vacuum energy. As the vacuum energy increases, there appears to be less reheating, since the energy of anisotropy is more efficiently converted into isotropic expansion. If the energy of anisotropy is large enough, the inflationary phase is prevented. In this case, a series of cosmological phase transitions will take place each time the square of the effective mass changes its sign.
Within the framework of the Bianchi type-IX homogeneous space, we set up a system of coupled equations for the cosmic scale factors, scalar field, and radiative energy density. At the tree level, the equations are written in a self-consistent, Hartree-Fock form. For phi"4 theory, the system of nine first-order differential equations is solved numerically for a varying ratio of the energy of anisotropy to the vacuum energy. As the vacuum energy increases, there appears to be less reheating, since the energy of anisotropy is more efficiently converted into isotropic expansion. If the energy of anisotropy is large enough, the inflationary phase is prevented. In this case, a series of cosmological phase transitions will take place each time the square of the effective mass changes its sign.
Recent advances in nanoscience have raised interest in the minimum bit size required for classical information storage. This bit size is determined by the necessity for bistability with suppressed quantum tunnelling and energy barriers that exceed ambient temperatures. In the case of magnetic information storage, much attention has centred on molecular magnets with bits consisting of about 100 atoms, magnetic uniaxial anisotropyenergy barriers of about 50?K and very slow relaxation at low temperatures. Here, we draw attention to the remarkable magnetic properties of some transition-metal dimers, which have energy barriers approaching 500?K with only two atoms. The spin dynamics of these ultrasmall nanomagnets is strongly affected by a Berry phase, which arises from quasi-degen...
Using the full potential linearized augmented plane wave (FLAPW) method, thickness dependent magnetic anisotropy of ultrathin FeCo alloy films in the range of 1 monolayer (ML) to 5 ML coverage on Pd(0 0 1) surface has been explored. We have found that the FeCo alloy films have close to half metallic state and well-known surface enhancement in thin film magnetism is observed in Fe atom, whereas the Co has rather stable magnetic moment. However, the largest magnetic moment in Fe and Co is found at 1 ML thickness. Interestingly, it has been observed that the interface magnetic moments of Fe and Co are almost the same as those of surface elements. The similar trend exists in orbital magnetic moment. This indicates that the strong hybridization between interface FeCo alloy and Pd gives rise to the large magnetic moment. Theoretically calculated magnetic anisotropy shows that the 1 ML FeCo alloy has in-plane magnetization, but the spin reorientation ...
Measurements are made on the principal magnetic susceptibilities and anisotropies of praseodymium selenate octahydrate single crystals in the temperature range 90 to 300 K. Although the effective magnetic moment is close to the free ion value, the anisotropy is quite high at room temperature. A least sequares fit of the Curie-Weiss law to the observed average susceptibility yields -36.5 K as the paramagnetic Curie temperature. An analysis of the results with a crystal field (CF) of D_4 symmetry, explains the observed results quite well. The CF and the spin-orbit interaction matrix is block diagonalized in the complete 33 dimensional basis of the "3H term in order to obtain the Stark energies and their eigenstates. Intermediate coupling effects are also considered. The ground state being a singlet, the g-factors are absent. Some predictions on the electronic heat capacity and the electronic quadrupole splitting are made in ...
We have obtained radial velocities for 69 stars in the globular cluster M2 (NGC 7089). M2's rotation axis is, within sizeable uncertainties, perpendicular to the major axis determined by the flattening. The ratio of rotational to random kinetic energy agrees with that predicted from the ellipticity assuming an oblate figure and an isotropic velocity-dispersion tensor. We have fitted King-Michie models to determine M2's mass, the exponent of an assumed power-law mass function, and the anisotropy radius. The most significant sources of uncertainty in the modeling are the velocity dispersion, the distance, and the mass-luminosity relation for the cluster stars. The models favor mass functions similar to or shallower than the Salpeter initial-mass function and a moderate amount of velocity anisotropy.
The defect-induced electron lifetime and energy-gap anisotropy effects on the T/sub c/ of the A-15 compounds are examined. A self-consistent model calculation demonstrates that the various defect dependences of T/sub c/ can be qualitatively understood in terms of the electron-lifetime effect.
The defect-induced electron lifetime and energy-gap anisotropy effects on the T/sub c/ of the A-15 compounds are examined. A self-consistent model calculation demonstrates that the various defect dependences of T/sub c/ can be qualitatively understood in terms of the electron-lifetime effect.
Recent analyses of the anisotropy of cosmic rays at 10{sup 18} eV (the AGASA and SUGAR data) show significant excesses from regions close to the galactic centre and Cygnus. Our aim is to check whether such anisotropies can be caused by single sources of charged particles. We investigate propagation of protons in two models of the galactic regular magnetic field (with the irregular component included) assuming that the particles are injected by a short-lived discrete source lying in the direction of the galactic centre. We show that apart from a prompt image of the source, the regular magnetic field may cause delayed images at quite large angular distances from the actual source direction. The image is strongly dependent on the time elapsed after ejection of particles and it is also very sensitive to their energy. For the most favourable conditions for particle acceleration by a young pulsar, the predicted fluxes are two to ...
Nonparabolicity of the heavy hole band in diamond-like semiconductors, which occurs within the framework of the three band model with the perturbation from the other bands taken into account according to the Loewdin procedure, is studied. A direct dependence of nonparabolicity on the band anisotropy (caused by the different effect of Gamma/sub 15c/ and Gamma/sub 12c/ bands) and the inverse dependence on the magnitude of the spin-orbit splittiing is established. A connection between the effective mass of heavy holes and their energy is obtained, which is valid for the majority of diamond-like semiconductors, except for materials with a very strong nonparabolicity of the band of silicon type
Nonparabolicity of the heavy hole band in diamond-like semiconductors, which occurs within the framework of the three band model with the perturbation from the other bands taken into account according to the Loewdin procedure, is studied. A direct dependence of nonparabolicity on the band anisotropy (caused by the different effect of Gamma/sub 15c/ and Gamma/sub 12c/ bands) and the inverse dependence on the magnitude of the spin-orbit splittiing is established. A connection between the effective mass of heavy holes and their energy is obtained, which is valid for the majority of diamond-like semiconductors, except for materials with a very strong nonparabolicity of the band of silicon type.
The subband structure and optical properties of a cylindrical quantum well wire under intense non-resonant laser field are investigated by taking into account the correct dressing effect for the confinement potential. The energy levels and wave functions are calculated within the effective mass- approximation using a finite element method. It is found that the absorption coefficient and the saturation intensity are strongly affected by the laser amplitude and frequency as well as by the incident light polarization. As a key result, a large anisotropy in the linear and nonlinear optical absorptions for very intense laser field is predicted. These effects can be useful for the design of polarization sensitive devices.
Focused Ion Beam (FIB) milling is a powerful tool to produce ordered magnetic nanostructures. However, it is impossible to produce out-of-plane magnetized nanoscale structures from multilayer films by direct FIB writing. Co/Pt multilayers exhibit an out-of-plane easy axis due to strong perpendicular interface anisotropy. The interface contribution is known to be very sensitive to high energy ion irradiation. In case of 30 keV Ga ions it needs less than one ion per 100 surface atoms to destroy the perpendicular interface anisotropy. We demonstrate how this problem can be overcome by milling a Co/Pt multilayer, which has been deposited on a SiN membrane, from the rear side, through the SiN. The effect of the ions is determined as a function of applied dose utilizing the domain structure imaged by soft X-ray holography. When the magnetic material is removed we find only a very narrow range of destruction around the holes in ...
The dd{yields}{sup 4}He{eta} reaction has been investigated near threshold using the ANKE facility at COSY-Juelich. Both total and differential cross-sections have been measured at two excess energies, Q=2.6 MeV and 7.7 MeV, with a subthreshold measurement being undertaken at Q=-2.6 MeV to study the physical background. While consistent with isotropy at the lower energy, the angular distribution reveals a pronounced anisotropy at the higher one, indicating the presence of higher partial waves. Options for the decomposition into partial amplitudes and their consequences for the determination of the s-wave {eta}{alpha} scattering length are discussed. (orig.)
Long-term modulation of galactic cosmic rays in interplanetary magnetic field (IMF) turbulence is a fundamental subject for understanding the connection between cosmic ray transport and solar activity. The discovery of a new cosmic ray modulation phenomenon is reported. Analysis of neutron monitor data has revealed that the difference in amplitude of the cosmic ray diurnal anisotropy for IMF sectors directed toward and away from the Sun displays a solar cycle variation. Neutron monitor data recorded at Climax, Deep River, Hyancayo, Kiel, Mt. Washington, and Swarthmore/Newark over the period 1957 to 1988 show that the amplitude difference varied between approximately 0.1 to -0.1 percent, with peaks in 1960, 1972, and 1982. A theoretical expression for this difference was derived from a three-dimensional model. Analysis also showed that the latitudinal density gradient of cosmic rays changed between 1.6 and -1.6 percent/AU with a solar cycle variation, which may ...
Molecular cluster predictions for electronic energy levels, wave functions, momentum densities, and Compton profiles of VO and VO_2 are examined within the Hartree-Fock-Slater model. VO_6 clusters are treated in O/subh/, D_4/subh/, and D_2/subh/ symmetry to obtain quantitative relations between distortion parameters and level shifts and splittings. Effects of the crystal environment are taken into account by a potential field. Results for VO are consistent with the augmented plane-wave band calculation of Mattheiss and x-ray emission data; the VO_2 levels are in good agreement with x-ray photoelectron spectroscopy data. A sizable anisotropy is predicted for the Compton profile of VO and VO_2.
A Monte Carlo simulation of the vacuum Bianchi type-IX (mixmaster) cosmology yields a significant correlation between large universe volume and high anisotropy. An analog of the model's chaotic classical behavior is seen in the break up of the universe wave function at large volume into fingers in the corners of the minisuperspace anisotropy potential.
This work reports the design of and experimentation with a topographically patterned cell culture substrate of variable local density and anisotropy as a facile and efficient platform to guide...Full Text Available
BackgroundFourier Transform Infrared Imaging (FTIRI) is used to investigate the amide anisotropies at different surfaces of a three-dimensional cartilage or tendon block. With the...Full Text Available
The spherical harmonic analysis of cosmic ray neutron data from the worldwide network neutron monitor stations during the years 1966 to 1969 was carried out. The second zonal harmonic component obtained from the analysis corresponds to the Pole-Equator anisotropy of the cosmic ray neutron intensity. Such an anisotropy makes a semiannual variation. In addition to this, it is shown that the Pole-Equator anisotropy makes a variation depending on the interplanetary magnetic field (IMF) sector polarities around the passages of the IMF sector boundary. A mechanism to interpret these results is also discussed.
Textured silicon nitride (Si_3N_4) has been intensively studied over the past 15 years because of its use for achieving its superthermal and mechanical properties. In this review we present the fundamental aspects of the processing and anisotropic properties of textured Si_3N_4, with emphasis on the anisotropic and abnormal grain growth of #beta#-Si_3N_4, texture structure and texture analysis, processing methods and anisotropic properties. On the basis of the texturing mechanisms, the processing methods described in this article have been classified into two types: hot-working (HW) and templated grain growth (TGG). The HW method includes the hot-pressing, hot-forging and sinter-forging techniques, and the TGG method includes the cold-pressing, extrusion, tape-casting and strong magnetic field alignment techniques for #beta#-Si_3N_4 seed crystals. Each processing technique is thoroughly discussed in terms of theoretical models and experimental data, including the texturing mechanisms ...
Recent preliminary results from the PAMELA satellite indicate the presence of a large flux of positrons (relative to electrons) in the cosmic ray spectrum between approximately 10 and 50 GeV. As annihilating dark matter particles in many models are predicted to contribute to the cosmic ray positron spectrum in this energy range, a great deal of interest has resulted from this observation. Here, we consider pulsars (rapidly spinning, magnetized neutron stars) as an alternative source of this signal. After calculating the contribution to the cosmic ray positron and electron spectra from pulsars, we find that the spectrum observed by PAMELA could plausibly originate from such sources. In particular, a significant contribution is expected from the sum of all mature pulsars throughout the Milky Way, as well as from the most nearby mature pulsars (such as Geminga and B0656+14). The signal from nearby pulsars is expected to generate a small but significant dipole ...
An in-plane uniaxial magnetic anisotropy has been observed in thin Co films normally deposited onto obliquely sputtered Ta and Pt underlayers. Associated with this anisotropy is an augmented easy axis coercivity. The in-plane easy axis is, in most cases, perpendicular to the incident deposition plane. Microstructural results indicate that grains are well connected along the magnetic easy axis but are separated by long continuous voids along the hard axis, which is ascribed to a geometric shadowing effect due to the oblique incidence deposition of the underlayer. Hence, the magnetic anisotropy mimics the film growth anisotropy. It is therefore believed that the observed magnetic properties are due to magnetostatic shape anisotropy effects. In-plane coercivity and anisotropy field are shown to increase with underlayer deposition angle, underlayer thickness and ...
When a metallic alloy is quenched into a miscibility gap, a mixture of two phases develops, whose domain structure then coarsens because of the interfacial energy between the two phases. This spatial arrangement of the domains and the rate at which they evolve may be strongly influenced by elastic interactions. In a recent paper, the authors described a method for simulating the effect of anisotropic elastic interactions in a two-dimensional Ising model of a cubic alloy, using Kawasaki dynamics with the elastic interactions represented by a long-range two-body interaction potential. Here they present the results of such simulations at various temperatures, alloy compositions and misfits (by misfit they mean the difference in size between the two kinds of atom), exhibiting snapshots both of the microscopic configurations (corresponding to experimental measurements using transmission electron microscopy) and of their squared Fourier transforms (corresponding to ...
We have analyzed data obtained with the Deep River neutron monitor and the underground vertical muon telescope at Embudo for the period 1965--79. Our data in conjunction with other published data show that for 1957--70 the diurnal anisotropy is unidirectional; with direction along 18 hour LT (east-west). During 1971--79, the diurnal anisotropy consists of two components. One is in east-west direction and the other is the radial component, with direction along 12 hour LT. The latter attains a maximum amplitude in 1976. We find no evidence for the existence of the twenty year wave in the diurnal anisotropy of cosmic rays. copyright American Geophysical Union 1988
Strong perpendicular anisotropy systems consisting of Co/Pt multilayer stacks that are antiferromagnetically coupled via thin Ru or NiO layers have been used as model systems to study the competition between local interlayer exchange and long-range dipolar interactions [1,2]. Magnetic Force Microscopy (MFM) studies of such systems reveal complex magnetic configurations with a mix of antiferromagnetic (AF) and ferromagnetic (FM) phases. However, MFM allows detecting surface stray fields only and can interact strongly with the magnetic structure of the sample, thus altering the original domain configuration of interest [3,4]. In the current study they combine magnetometry and state-of-the-art soft X-ray transmission microscopy (MXTM) to investigate the external field driven FM phase evolution originating from the domain boundaries in such antiferromagnetically coupled perpendicular anisotropy films. MXTM allows directly imaging the perpendicular ...
A Monte Carlo simulation of the vacuum Bianchi type-IX (mixmaster) cosmology yields a significant correlation between large universe volume and high anisotropy. An analog of the model's chaotic classical behavior is seen in the break up of the universe wave function at large volume into fingers in the corners of the minisuperspace anisotropy potential.
Two aspects of the deformation behavior of magnesium sheets are the subject of this paper. First it will give a mechanical characterization of a commercial magnesium with a focus on the anisotropy and the possible microstructural causes of this behavior. The rolling process will be part of the second aspect. The aim is to show the influence of the parameters on the microstructure and texture and how this could affect the anisotropy in the rolled sheets. (Abstract Copyright [2003], Wiley Periodicals, Inc.)
It if first shown, that the effective field of uniaxial magnetic anisotropy of Fe-Cr-P-C and Fe-Ni-B-Si system amorphous alloys is reduced with an increase of the source melt isothermal exposure time. The behaviour noted is conditioned by microcoherence and relaxation processes in the nonequilibrium liquid phase after crystal-liquid phase transition.
Magnetic field, thickness and magnetic forming effect on general mode and quantitative parameters of the domain structure (DS) of ferrite-garnet (EuEr)/sub 3/(FeGa)/sub 5/O/sub 12/ monocrystalline plates (111) is investigated. Field interval of circle (cone) and ring domain stability is determined. It is shown that DS of ferrite-garnet crystals with uniaxial an6sotropy has some peculiarities, that can be explained by cubic anisotropy effect.
We report the experimental and theoretical results on the anisotropies in the magnetic properties and x-ray absorption spectra of single-crystal LiFePO4. A mean-field theory is developed to explain the observed strong anisotropies in Lande g-factor, paramagnetic Curie temperature, and effective moment for LiFePO4 single crystals. The values of the in-plane nearest- and next-nearest-neighbor spin exchange (J1 and J2), interplane spin exchange (J{perpendicular}), and single-ion anisotropy (D), obtained recently from neutron scattering measurements, are used for calculating the Curie temperatures with the formulas derived from the mean-field Hamiltonian. It is found that the calculated Curie temperatures match well with that obtained by fitting the magnetic susceptibility curves to the modified Curie-Weiss law. For the polarized Fe K-edge x-ray absorption spectra of single-crystal LiFePO4, a different feature assignment for ...
The galvanomagnetic properties of single-crystal samples of the Bi{sub 0.93}Sb{sub 0.07} semiconductor alloy with the electron density n = 1.6 x 10{sup 17} cm{sup -3} in magnetic fields up to 14 T at T = 1.6 K have been investigated. The resistivity {rho} and Hall coefficient R have been measured as functions of the magnetic field directed along the binary axis of a crystal for a current flowing through a sample along the bisector axis; i.e., the components {rho}{sub 22} and R{sub 32,1} have been measured. The strong anisotropy of the electron spectrum of the samples makes it possible to separately observe quantum oscillations of the magnetoresistance {rho}{sub 22}(H) for H -parallel C{sub 2} in low magnetic fields for two equivalent ellipsoids with small extremal cross sections (secondary ellipsoids) and in high magnetic fields for electrons of the ellipsoid with a large extremal cross section (main ellipsoid). An increase in the energy of the ...
In a first paper (Forni & Aghanim 1999), we developed several statistical discriminators to test the non-gaussian nature of a signal. These tests are based on the study of the coefficients in a wavelet decomposition basis. In this paper, we apply them in a cosmological context, to the study of the nature of the Cosmic Microwave Background (CMB) anisotropies. The latter represent the superposition of primary anisotropy imprints of the initial density perturbations and secondary ones due to photon interactions after recombination. In an inflationary scenario (standard Cold Dark Matter) with gaussian distributed fluctuations, we study the statistical signature of the secondary effects. More specifically, we investigate the dominant effects arising from the Compton scattering of CMB photons in ionised regions of the Universe: the Sunyaev-Zel'dovich effect of galaxy clusters and the effects of a spatially inhomogeneous re-ionisation of the ...
The evolution of Bianchi type-I and type-IX universes for a theory of gravity with an #epsilon#R"2 term added to the usual Lagrangian is considered. As in the spatially flat Robertson-Walker case considered previously by others, inflation is found to occur. For any amount of initial anisotropy, the anisotropy decays quickly relative to the length of the inflationary epoch, and the amount of expansion is enhanced by the anisotropy. The exceptions are Bianchi type-IX universes near or at isotropy. In these cases a wide range of initial parameters causes the universe to recollapse, thus reducing the phase space in which inflation can occur. The diagonal metric is shown to be the most general form in the R"2 theory for both Bianchi type-I universes with a perfect fluid and vacuum Bianchi type-IX models.
The evolution of Bianchi type-I and type-IX universes for a theory of gravity with an {epsilon}{ital R}{sup 2} term added to the usual Lagrangian is considered. As in the spatially flat Robertson-Walker case considered previously by others, inflation is found to occur. For any amount of initial anisotropy, the anisotropy decays quickly relative to the length of the inflationary epoch, and the amount of expansion is enhanced by the anisotropy. The exceptions are Bianchi type-IX universes near or at isotropy. In these cases a wide range of initial parameters causes the universe to recollapse, thus reducing the phase space in which inflation can occur. The diagonal metric is shown to be the most general form in the {ital R}{sup 2} theory for both Bianchi type-I universes with a perfect fluid and vacuum Bianchi type-IX models.
Dark matter particles form halos that contribute the major part of the mass of galaxy clusters. The formation of these cosmological structures have been investigated both observationally and in numerical simulations, which have confirmed the existence of a universal mass profile. However, the dynamic behaviour of dark matter in halos is not as well understood. We have used observations of 16 equilibrated galaxy clusters to show that the random velocities of dark matter particles are larger on average along the radial direction than along the tangential, and that the magnitude of this velocity anisotropy is radially varying. Our measurement implies that the collective behaviour of dark matter particles is fundamentally different from that of normal particles and the radial variation of the anisotropy velocity agrees with the predictions of numerical simulation.
Car weight corresponds directly to fuel consumption and driving performance. So in order to improve the fuel efficiency and performance of a car the weight has to be reduced. Magnesium as a light metal offers a wide range of weight saving opportunities, especially Magnesium wrought alloys with their improved mechanical properties have a high potential for structural applications. Mechanical properties in terms of their quality and anisotropy are dependent on the microstructure of the material and can be characterized by their degree of inhomogeneity, their grain size distribution and their crystallographic texture. Therefore the orientation distribution of grains, the grain size, its size distribution, the chemical composition (precipitates) itself influence the mechanical parameters and their anisotropy. In this presentation first results of mechanical anisotropy are given: differences in yield stress, r-values and their ...
The work reported here concerns the evolution of the shape of a coherent, cubic precipitate as it grows by coarsening. The work was motivated by the need to explain recent experimental observations that show that cuboidal ..gamma.. Ni/sub 3/Al precipitates in Ni-Al alloys resist coarsening and decompose into doublets of parallel rectangular plates and octets of small cubes. The theoretical model assumes a precipitate of cubic phase with negative elastic anisotropy, and neglects any difference between the elastic constants of the precipitate and the matrix. The elastic energy of the precipitate is then calculated as a function of its morphology, including the possibility of decomposition into doublets or octets of discrete particles. The results show that a cuboidal precipitate with (100) faces and edge length, 2a, is metastable with respect to transition to a doublet of discrete plates, with dimensions a x 2a x 2a, that are separated by the ...
This paper reports on Monte Carlo path integral simulations of a Bianchi Type IX cosmology which yield a wave function which reflects the known chaotic dynamics of the classical system and predicts a significant probability for a correlation between large universe volume and large anisotropy.
If we decompose C1 using SVD the parameter covariance matrix can be inverted to ... However, we can analyze the parameter covariance matrix directly by ...
Anisotropy has been investigated using S-wave as a technique for detecting fractures. In this study, fundamental experiments were carried out with slightly changing the measuring conditions at a place where anisotropy was expected. This paper describes the fundamental data acquisition of anisotropy analysis using S-wave, and a part of the results. The experiments were conducted on the agricultural road in Yamadera district, Matsuyama-machi, Yamagata Prefecture. Two flat unpaved roads meeting at right angles were used as traverse lines. In this place, several reflection surfaces were certainly detected by P-wave, and anisotropy of S-wave was confirmed from the velocity of refracted wave of S-wave. Data were processed for individual traverse lines meeting at right angles. Firstly, signal sweeping, correlation, and vertical superposition were made. Six kinds of data were prepared, i.e., three-component ...
To calibrate channels A1 to A4 for particles with Z >= 1, tests were done on the IBIS accelerator at AERE, Harwell, which gave protons up to 3 MeV. ...
The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. ...
An anisotropic power spectrum will have a clear signature in the 21cm radiation from high- redshift hydrogen. We calculate the expected power spectrum of the intensity fluctuations in neutral hydrogen from before the epoch of reionization, and predict the accuracy to which future experiments could constrain a quadrupole anisotropy in the power spectrum. We find that the Square Kilometer Array will have marginal detection abilities for this signal at z~17 if the process of reionization has not yet started; reionization could enhance the detectability substantially. Pushing to higher redshifts and higher sensitivity will allow highly precise (percent level) measurements of anisotropy.
We report on a promising approach to high-sensitivity anisotropy measurements using a high-finesse cavity locked by optical feedback to a diode laser. We provide a simple and effective way to decouple the weak anisotropy of interest from the inherent mirror's birefringence whose drift may be identified as the key limiting parameter in cavity-based techniques. We demonstrate a shot-noise-limited phase shift resolution previously inaccessible in an optical cavity, readily achieving the state-of-the-art level of 3x10"-"1"3 rad.
The paramagnetic susceptibility of single crystals of dysprosium-yttirum alloys is measured in the basal plane and along the hexagonal axis. It is shown that the susceptibility of the alloys obeys the Curie-Weiss law, the effective magnetic moments allong the different directions being the same and the paramagnetic Curie temperatures being different. The difference between the paramagnetic Curie temperatures in the basal plane and along the hexagonal axis is independent of the dysprosium concentration in the alloy. As a comparison with the theoretical models of magnetic anisotropy shows, this is an indication that the magnetic anisotropy of dysprosium - yttrium alloys is of a single-ion nature.
The room-temperature anisotropy of amorphous Fe_4_0Ni_3_8Mo_4B_1_8 (METGLAS 2628MB) ribbons after various heat treatments has been studied by Moessbauer spectroscopy. The average magnetization direction becomes significantly more out-of-plane after heating above 650 K but below the crystallization temperature. X-ray diffractograms suggest an atomic rearrangement has occurred. (orig.).
It is noted that the existence of cosmic-ray semidiurnal anisotropy of interplanetary origin has generally been attributed to the symmetrically rising density gradients perpendicular to the solar equatorial plane. An increase in the magnitude of the semidiurnal anisotropy of cosmic rays during the years 1973-1975 by a factor of 2 is in theory expected to be associated with larger magnitudes of the heliolatitudinal density gradients. The distribution of cosmic-ray intensity in the heliolatitude range + or - 7.25 deg obtained using the data of the Deep River neutron monitor is shown not to support the density gradient hypothesis. The presence of symmetrical gradients at higher heliolatitudes, however, cannot be ruled out.
The anisotropy of H/sub c2/ was measured in a V$sub 3$Si monocrystal and was found to be much larger than in other materials. The max elementary pinning force f/sub p/ is estimated to be approximately 0.01 dyn/cm at the reduced field H/H/sub c/ = 0.25 and 4.2$sup 0$K. Control of texture as well as of grain size is important for improving J/sub c/ in A-15 compounds. (DLC)
A sample of 41 radio-galaxies with 13.0<=msub(corr)<=15.5 has been analyzed to test the angular redshift anisotropy discovered on Sc I galaxies by Rubin, Rubin and Ford (1973). The sample does not present their anisotropy but contains an even more curious distribution of radial velocities which suggests that the Rubin-Ford effect results from an anomalous redshift of light when it travels through clusters of galaxies. (Auth.).
This thesis deals with the special electronic properties of the transition-metal aluminides. Following quasicrystals and their approximants it is shown that even materials with small elementary cells exhibit the same surprising effects. So among the transition-metal aluminides also semi-metallic and semiconducting compounds exist, although if they consist of classic-metallic components like Fe, Al, or Cr. These properties are furthermore coupled with a deep pseusogap respectively gap in the density of states and strongly covalent bonds. Bonds are described in this thesis by two eseential properties. First by the bond charge and second by the energetic effect of the bond. It results that in the caes of semiconducting transition-metal aluminides both a saturation of certain bonds and a bond-antibond alteration in the Fermi level is present. By the analysis of the near-order in form of the so-calles coordination polyeders it has been succeeded to establish a simple rule for ...
The double diffusive convection in a horizontal couple stress fluid saturated anisotropic porous layer, which is heated and salted from below, is studied analytically. The modified Darcy equation that includes the time derivative term is used to model the momentum equation. The critical Rayleigh number, wavenumber for stationary and oscillatory modes, and frequency of oscillations are obtained analytically using linear theory. The effect of anisotropy parameter, solute Rayleigh number, Lewis number, couple stress parameter, and Vadasz number on the stationary, oscillatory, and finite amplitude convection is shown graphically. It is found that the thermal anisotropy parameter, couple stress parameter, and solute Rayleigh number have stabilizing effect on the stationary, oscillatory, and fin...
In this Letter, we demonstrate the application of time-resolved fluorescence anisotropy measurements to detect solution state hybridization of streptavidin conjugate (CdSe)ZnS quantum dots (QD). The study was performed on samples containing 10nM QD incubated with 800nM DNA. We show that the rotational correlation time of QD-DNA constructs increases significantly upon hybridization with values of 330ns (QD-ssDNA) and 1.3ms (QD-dsDNA), corresponding to a diameter of 14nm and 23nm respectively. The present study opens a new modality for hybridization detection using quantum dots.
The behaviour of the wave function of the universe under the barrier for the anisotropic cosmological Bianchi type-IX model taking account of the scalar field is explored. In view of the known difficulties with the interpretation of multidimensional ones is offered. For this purpose in the frameworks of the semiclassical approach the system of characteristics equations relative to one variable is written out. This system describes a bundle of the characteristics along which the multidimensional problem is reduced to a one-dimensional one that allows to utilize the standard interpretation of the wave function as well as the usual Schroedinger equation. The obtained results for the Bianchi type-IX model are reduced to the following statement: the universe tunnels through the barrier from an isotropic state with small anisotropy that is necessary for providing a ling-lived inflation to derive the universe.
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no semiclassical components which would correspond to Lorentzian universes. For the case with a cosmological constant the Hartle-Hawking boundary conditions formally constrain one of the parameters in the Lorentzian solutions to be purely imaginary. Possible interpretations of this imaginary parameter are ...
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no semiclassical components which would correspond to Lorentzian universes. For the case with a cosmological constant the Hartle-Hawking boundary conditions formally constrain one of the parameters in the Lorentzian solutions to be purely imaginary. Possible interpretations of this imaginary parameter are ...
The authors examine the relationship of the structure and mechanical properties of similar alloys of tungsten with rhenium produced by the powder metallurgy method by sintering powders. Since the alloys were deformed by rolling, we examine the effect of the resultant anisotropy of the structure on the properties of the metal in various directions. The tests were conducted on an alloy of tungsten with 2 wt.% rhenium and, for comparison purposes, an alloy of tungsten with additions of oxides of yttrium and hafnium. The mechanical properties of the alloys, i.e., strength, cracking resistance, cold shortness temperature, were determined in the bend test. Structural examination was carried out using an optical microscope, electron scanning microscopy, and the method of transmission electron microscopy.
An investigation of the Ll x-#gamma# angular correlations following the decay of "2"0"7Bi is done by using a Si(Li) semiconductor counter as L x-ray detector. Coincidence measurements at five different angles were made between the 570-keV #gamma# ray (gated in the movable counter) and the Ll x spectrum (displayed in a multichannel analyzer).
The wavefunction of a positron in ReO is calculated using the augmented-plane-wave method. Due to the loosely-packed structure of ReO_3, the ground-state GAMMA_1 wavefunction exhibits a marked anisotropy particularly around the oxygen ions, and a large fraction of a positron is distributed in the interstitial region. Experimental results of the positron annihilation 2#gamma#-correlations and the positron annihilation rates in ReO_3 are discussed based on the positron wavefunction. (orig.).
The cosmic no hair theorem is studied in anisotropic brane worlds. Assuming anisotropic Bianchi models with an inflaton field it is shown that, during slow-roll inflation, anisotropy in all Bianchi models except a Bianchi type-IX universe washes out. Brane worlds admit both exponential and power law inflation. We consider here only exponential expansion of the universe. It is found that isotropization occurs much faster in a brane world than in the general theory of relativity.
After presenting three ways of defining a bulge component in disc galaxies, we introduce the various types of bulges, namely the classical bulges, the boxy/peanut bulges and the disc-like bulges. We then discuss three specific topics linked to bulge formation and evolution, namely the coupled time evolution of the bar, buckling and peanut strengths; the effect of velocity anisotropy on peanut formation; and bulge formation via bar destruction.
As the jump from 2D to 3D, seismic exploration lives a new revolution with the use of converted PS waves. Indeed PS converted waves are proving their potential as a tool for imaging through gas; lithology discrimination; structural confirmation; and more. Nevertheless, processing converted shear data and in particular determining accurate P and S velocity models for depth imaging of these data is still a challenging problem, especially when the subsurface is anisotropic. To solve this velocity model determination problem we propose to use reflection travel time tomography. In a first step, we derive a new approximation of the exact phase velocity equation of the SV wave in anisotropic (TI) media. This new approximation is valid for non-weak anisotropy and is mathematically simpler to handle than the exact equation. Then, starting from an isotropic reflection tomography tool developed at Lt-'P, we extend the isotropic bending ray tracing method to the ...
A consistent combination of quantum geometry effects rules out a large class of models of loop quantum cosmology and their critical densities as they have been used in the recent literature. In particular, the critical density at which an isotropic universe filled with a free, massless scalar field would bounce must be well below the Planck density. In the presence of anisotropy, no model of the Schwarzschild black hole interior analyzed so far is consistent.
On the basis of symmetry way of texture description a calculation method of elastic moduli of two-phase titanium alloys with rolling texture has been suggested. Efficiency of the calculation formulas is checked by comparing the calculation results of Young modulus anisotropy in the sheet plane of (#alpha#+#beta#)-titanium alloy VT23 with the experimental data.
This research is to provide improved strategies for enhanced oil recovery from the Tensleep Sandstone oil reservoirs in the Bighorn and Wind River basins, Wyoming. Because of the great range of API gravities of the oils produced from these reservoirs, the proposed study concentrates on understanding the spatial variation and anisotropy of relative permeability within the Tensleep Sandstone. This research will associate those spatial distributions and anisotropies with the depositional subfacies and zones of diagenetic alteration found within the sandstone. The associations of the above with pore geometry will link relative permeability with the dimensions of lithofacies and authigenic mineral facies. Hence, the study is to provide criteria for scaling this parameter on a range of scales, from the laboratory to the basin-wide scale of subfacies distribution. Effects of depositional processes and burial diagenesis will be investigated. Image ...
We present a set of exact solutions for quantum Bianchi type-IX anisotropic cosmological models (including the Taub model) of the form {Psi}={ital We}{sup {minus}{ital S}}. These solutions are spread over all values of anisotropy near the singularity, but at larger values of the radius of the universe they are strongly peaked around the {ital k}=+1 Friedmann-Robertson-Walker model.
In order to simplify the coke manufacturing process, a coke production mechanism in coal pyrolysis was discussed. Australian bituminous coal which can produce good coke was used for the discussion. At a temperature raising rate of 50{degree}C per minute, coal weight loss increases monotonously. However, in the case of 3{degree}C, the weight loss reaches a peak at a maximum ultimate temperature of about 550{degree}C. The reaction mechanism varies with the temperature raising rates, and in the case of 50{degree}C per minute, volatiles other than CO2 and propane increased. Weight loss of coal at 3{degree}C per minute was caused mainly by methane production at 550{degree}C or lower. When the temperature is raised to 600{degree}C, tar and CO2 increased, and so did the weight loss. Anisotropy was discerned in almost of all coke particles at 450{degree}C, and the anisotropy became remarkable with increase in the maximum ultimate temperature. Coke and ...
A procedure and software have been developed to transform the area distribution of the residual surface heights available from the measurement with the Micromap interferometric microscope into a two-dimensional (2D) power spectral density (PSD) distribution of the surface height. The procedure incorporates correction of one of the spectral distortions of the PSD measurement. The distortion appears as a shape difference between the tangential and sagittal PSD spectra deduced from the 2D PSD distribution for an isotropic surface. A detailed investigation of the origin of the anisotropy was performed, and a mathematical model was developed and used to correct the distortion. The correction employs a modulation transfer function (MTF) of the detector deduced analytically based on an experimentally confirmed assumption about the origin of the anisotropy due to the asymmetry of the read-out process of the instrument's CCD camera. The ...
Satellite CMB anisotropy missions and new generation of balloon-borne and ground experiments, make use of complex multi-frequency instruments at the focus of a meter class telescope. Between 70 GHz and 300 GHz, where foreground contamination is minimum, it is extremely important to reach the best trade-off between the improvement of the angular resolution and the minimization of the straylight contamination mainly due to the Galactic emission. We focus here, as a working case, on the 30 and 100 GHz channels of the Planck Low Frequency Instrument (LFI). We evaluate the GSC introduced by the most relevant Galactic foreground components for a reference set of optical configurations. We show that it is possible to improve the angular resolution of 5-7% by keeping the overall GSC below the level of few microKelvin. A comparison between the level of straylight introduced by the different Galactic components for different beam regions is presented. Simple approximate ...
We have investigated the possibility to use a microwire of BiSn to design an anisotropic thermoelectric generator. The glass-coated microwire of pure and Sn-doped bismuth was obtained by the Ulitovsky method; it was a cylindrical single-crystal with orientation (1011) along the wire axis; the C3 axis was inclined at an angle of 70 degrees to the microwire axis. It is found that doping of bismuth wires with tin increases the thermopower anisotropy in comparison with Bi by a factor of 2 - 3 in the temperature range of 200-300 K. For a Bi microwire with a core diameter of 10 ?m with a glass coating with outer diameter of 35 ?m, the transverse thermopower is ? 150 ?V/(K*cm); for BiSn, 300 ?V/(K*cm). The design of an anisotropic thermogenerator based on BiSn microwire is proposed. The miniature thermogenerator will be efficient for power supply of devices with low useful current. In addition to the considerable thermopower anisotropy of BiSn wires ...
Reflectance anisotropy spectroscopy (RAS) has been used, together with scanning tunnelling spectroscopy (STS), to investigate the optical and electronic properties of nanodots formed by depositing Ag on the Si(111)-3 x 1-Ag surface. One-dimensional (1D) arrays of nanodots were grown on a single-domain (3 x 1)-Ag surface and the anisotropic optical response in the 0.5-5 eV range measured by RAS. Aligned, elongated Ag islands were also grown on this surface to compare their properties with those of the nanodots. STS of the Ag islands showed distinct metallic behaviour, whereas the nanodots revealed a bandgap of #approx#0.6 eV, indicating that the surface of the dots has a non-metallic character, similar to that of the Si(111)-3 x 1-Ag surface. RAS also showed substantial differences between the structures, with a large infrared anisotropy for the metallic Ag islands consistent with anisotropic Drude-like intraband transitions, whereas the ...
We review the data on long-term changes in the solar diurnal variation of cosmic rays, observed at Deep River with a neutron monitor and at Embudo with an underground muon telescope, during the period 1965-1976. We show that the model proposed by Erdos and Kota (1979, Sixteenth ICCR, Kyoto. Conference Papers 4, 45). cannot explain the systematic changes seen in our data during 1971-1976. An insight gained from the diffusion-convection model enables us to obtain a unique solution for K parallel to Gsub(r) in terms of the parameters applicable to the solar wind and the diurnal anisotropy. This helps us calculate the rigidity (R) dependence of the diffusion coefficent K parallel. We find that K parallel = 1.37 x 10/sup 18/ Rsup(0.6) m/sup 2/s/sup -1/, where R is in gigavolts, and K perpendicular 1.08 x 10/sup 18/ m/sup 2/s/sup -1/. Our results are discussed.
We performed density functional calculations to examine the effects of solvation, hydrogen bonding, backbone conformation, and the side chain on 15N chemical shielding in proteins. We used N-methylacetamide (NMA) and N-formyl-alanyl-X (with X being one of the 19 naturally occurring amino acids excluding proline) as model systems. In addition, calculations were performed for selected fragments from protein GB3. The conducting polarizable continuum model was employed to include the effect of solvent in the density functional calculations. Our calculations for NMA show that the augmentation of the polarizable continuum model with the explicit water molecules in the first solvation shell has a significant influence on isotropic 15N chemical shift but not as much on the chemical shift anisotropy. The difference in the isotropic chemical shift between the standard ?-sheet and ?-helical conformations ranges from 0.8 to 6.2 ppm depending on the residue type, with the mean ...
Correlations are studied between the power density of Alfv\\'en-cyclotron waves (having frequencies between 0.02 and 2 Hz) and the ratio of the perpendicular and parallel temperature of the protons. The wave power spectrum is evaluated from high-resolution 3D magnetic field vector components, and the ion temperatures are derived from the velocity distribution functions as measured in fast solar wind during the Helios-2 primary mission at radial distances from the Sun between 0.3 AU and 0.9 AU. From our statistical analysis, we obtain a striking correlation between the increases in the proton temperature ratio and enhancements in the wave power spectrum. Near the Sun the transverse part of the wave power is often found to be by more than an order of magnitude higher than its longitudinal counterpart. Also the measured ion temperature anisotropy appears to be limited by the theoretical threshold value for the ion-cyclotron instability. This suggests that ...
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no rapidly oscillating semiclassical components in the wave function, and hence do not recover lorentzian space-time as a prediction of the no-boundary proposal. For the case with a cosmological constant the wave function does contain rapidly oscillating components and thus predicts approximately ...
We investigate the quantum cosmology of spatially homogeneous models with compact spatial sections admitting a u(2) isometry algebra. The metric ansatz in these models is that of Bianchi type IX with two scale factors set to be equal. We apply the Hartle-Hawking no-boundary path integral prescription and find the semi-classical contributions to the wave function. Exact formulae are obtainable for certain contributions and otherwise the limits of large and small anisotropy (for the pure vacuum case) and large spatial volume or small anisotropy (for the case with a positive cosmological constant) are considered. For the pure vacuum case we find no rapidly oscillating semiclassical components in the wave function, and hence do not recover lorentzian space-time as a prediction of the no-boundary proposal. For the case with a cosmological constant the wave function does contain rapidly oscillating components and thus predicts approximately ...
The pH of the solution is shown to significantly effect the reflection anisotropy spectroscopy (RAS) profiles of adenine adsorbed at Au(110)/electrolyte interfaces. At pH 12.8 the net adsorption is very weak due the formation of negative adenine ions in solution. The sensitivity of the RAS profiles to the pH of the solution is probably due to a change in the geometry of the adsorbed molecules caused by a disruption of the base stacking configuration that is adopted when adenine is adsorbed from solutions at pH 7.1. (Abstract Copyright [2010], Wiley Periodicals, Inc.)
Axially symmetric waveguides, resonators, and scatterers of arbitrary cross section and anisotropy in the cross section can be modeled rigorously with use of 2-D Cartesian-grid based codes by means of mere redefinition of material permittivity and permeability profiles. The method is illustrated by the frequencydomain simulations of resonant modes in a circular-cylinder cavity with perfectly conducting walls, a shielded uniaxial anisotropic dielectric cylinder, and an open dielectric sphere for which, after proper implementation of the perfectly matched layer boundary conditions, the radiation quality factor is also determined.
Formation of basis type texture at rolling of Ti + 6.0% Al + 1.5% V + 1.0% Mo system alloy with initial prismatic texture is investigated by means of X-ray techniques. Variations of mechanical features in titanium alloy sheets depending on temperature-deformation conditions of rolling are investigated. Main conditions for formation of the intensive basis textute in the investigated alloy sheets which provides for isotropic properties in sheet plane and for increased ductility are determined.
We provide a both qualitative and quantitative comparison among different approaches aimed to solve the problem of non-linear diffusive acceleration of particles at shocks. In particular, we show that state-of-the-art models (numerical, Monte Carlo and semi-analytical), even if based on different physical assumptions and implementations, for typical environmental parameters lead to very consistent results in terms of shock hydrodynamics, cosmic ray spectrum and also escaping flux spectrum and anisotropy. Strong points and limits of each approach are also discussed, as a function of the problem one wants to study.
The work is devoted to the construction of a viable of locally anisotropic, i.e. Finslerian, space-time and to the generalization, on this basis, of the relativistic theory of gravitation. Arguments in favour of this model are considered. From physical considerations the concrete form of the Finslerian metric has been reconstructed and within the framework of the correspondence principle a formalism of the theory has been developed. The approach suggested is aimed at developing unified gauge theories of all fundamental interactions. Much attention is given to the nontrivial physical manifestations of local space anisotropy and to the possibility of its experimental detection. (orig.)
The work in the past year has primarily involved four areas of magnetic thin films: amorphous rare earth-transition metal alloys, epitaxial CoPt{sub 3} and Ni-Pt alloy thin films, amorphous rare earth doped Si (a new class of dilute magnetic semiconductor with large negative magnetoresistance which the authors have discovered), and exchange-coupled antiferromagnetic insulators. In the amorphous alloys, they made a systematic study of the effects of local anisotropy, macroscopic (perpendicular) anisotropy, and exchange constant on the fundamental (and practical) properties of these magnetic alloys, as originally described in the grant proposal. The work on the epitaxial Co-Pt (and more recently Ni-Pt) alloys was originally undertaken as a comparison study to the amorphous alloys. Crystalline Co-Pt alloys have many striking similarities to the amorphous rare earth-transition metal alloys: perpendicular magnetic anisotropy, ...
A scaling Monte Carlo method has been developed to calculate diffuse reflectance from multilayered media with a wide range of optical properties in the ultraviolet-visible wavelength range. This multilayered scaling method employs the photon trajectory information generated from a single baseline Monte Carlo simulation of a homogeneous medium to scale the exit distance and exit weight of photons for a new set of optical properties in the multilayered medium. The scaling method is particularly suited to simulating diffuse reflectance spectra or creating a Monte Carlo database to extract optical properties of layered media, both of which are demonstrated in this paper. Particularly, it was found that the root-mean-square error (RMSE) between scaled diffuse reflectance, for which the anisotropy factor and refractive index in the baseline simulation were, respectively, 0.9 and 1.338, and independently simulated diffuse reflectance was less than or equal to 5% for ...
Buildings Energy-Efficient Research Laboratories Energy Efficiency in Federal Facilities Energy Efficiency Standards Group Energy Efficient Windows Collaborative Energy &...
Results of X-ray investigations of solid normal hydrogen are presented. Temperature dependences of the lattice parameteps, molar volumes, linear and volume expansion coefficients in the 2K-Tsub(melt) temperature range are obtaiped. An essential n-H/sub 2/ expansion anisotropy in the premelting temperature region is pointed out. It is shown that the hexagonal lattice parameter ratios over the whole investigated temperature range is considerably higher than for solid parahydrogen. A considerable difference in thermal expansion of normal hydrogen and parahydrogen in the low temperature region is revealed. It is caused by contribuation of a rotational subsystem, increasing with the temperature decrease to crystal expansion. A detailed analysis of solid n-H/sub 2/ thermodynamic properties is conducted. The data testifying to the presence of isomorphous phase transformation in the solid n-H/sub 2/ in the premelting temperature region are discussed.
ObjectivesThe objective of this meeting will be to interface the two ends of the particulate flow spectrum - those working to understand the fundamentals of granular flows and those attempting to control particulate flows in an industrial setting - to develop solutions to the complex problems presented by dense granular flows. We will aim~%~~%~to provide a forum for the interface between practical users of particulate technology and the developers of theories for understanding granular flow;~%~to present [continued...]DescriptionIn practical situations such as those met in industry where segregation and mixing are important, understanding particulate flows is complex due to the presence of polydispersity, anisotropy and complex grain morphology. In attempting to model such systems, many of these features are generally ignored, except perhaps through empirical parameter fitting. Developing a theory to include these effects is a considerable ...
The physicochemical properties of binary lipid mixtures of diether C25,25 lipids and dipalmitoyl-L-a-phosphatidylcholine (DPPC) were studied using photon correlation, fluorescence and electron paramagnetic resonance spectroscopy, and transmission electron microscopy. These two types of lipids can be mixed at all molar ratios to form unilamellar and multilamellar liposomes. Fluorescence anisotropy of 1,6-diphenyl-1,3,5-hexatrien in mixed liposomes indicates that the abrupt changes in order parameter in the hydrophobic part of bilayer membranes made of DPPC lipids disappears with increasing mol%C25,25 lipids. Electron paramagnetic resonance spectroscopy shows that at temperatures below 50^oC, the interfacial regions of membrane bilayer of mixed liposomes is more fluid than for pure DPPC lipo...
Natural fractures and in situ stresses commonly dictate subsurface reservoir permeability and permeability anisotropy, as well as the effectiveness of stimulation techniques in low-permeability, natural gas reservoirs. This paper offers an initial prediction for the orientations of the fracture and stress systems in the tight gas reservoirs of the Frontier Formation, in the Green River basin of southwestern Wyoming. It builds on a previous report that addressed fractures and stresses in the western part of the basin and on ideas developed for the rest of the basin, using the principle that thrust faults are capable of affecting the stress magnitudes and orientations in little-deformed strata several hundreds of kilometers in front of a thrust. The prediction of subsurface stresses and natural fracture orientations is an undertaking that requires the willingness to revise models as definitive data are acquired during drilling. The predictions made in this paper are ...
The purpose of this experimental study is to investigate the micromechanical fatigue behavior, in terms of slip nature and preferential cracking sites, of a commercial #alpha#/#beta#-forged Ti-6Al-4V alloy. Electron backscattering diffraction is extensively used to identify the deformation (prismatic, basal, pyramidal slip) and crack formation modes activated by fatigue at the surface of several hundred primary #alpha# nodules. Some fatal crack formation sites are also characterized. Cracking in basal planes is identified as the most critical damage mode leading to fracture. An explanation is proposed which involves the resolved shear stress, taking into account the Schmid factor and the normal stress in relation to the elastic anisotropy of the #alpha#-phase. Finally, the spatial distribution of the secondary cracks is analyzed according to the crystallographic textures (macrozones) present on a mesoscopic scale in the Ti-6Al-4V alloy.
The electrical resistivity, Hall effect, and magnetic susceptibility of single-crystal UPd_2Si_2 have been studied between 4.2 and 300 K. A large anisotropy was observed in both the magnetic and transport properties. There is a quadratic temperature dependence of the resistivity for a range of temperatures between 4.2 and 80 K. At higher temperatures, the resistivity indicates a Kondo-type behavior. The behavior of these quantities is accounted for by the magnetic phase transitions at 108 and 136 K reported from neutron-scattering studies. At high temperatures, the magnetic susceptibility of UPd_2Si_2 is Curie-Wiess-like along the c axis. The temperature dependence of the Hall coefficient above 108 K is accounted for by a theoretical model invoking skew scattering of conduction electrons by localized magnetic moments.
The electrical resistivity, Hall effect, and magnetic susceptibility of single-crystal UPd[sub 2]Si[sub 2] have been studied between 4.2 and 300 K. A large anisotropy was observed in both the magnetic and transport properties. There is a quadratic temperature dependence of the resistivity for a range of temperatures between 4.2 and 80 K. At higher temperatures, the resistivity indicates a Kondo-type behavior. The behavior of these quantities is accounted for by the magnetic phase transitions at 108 and 136 K reported from neutron-scattering studies. At high temperatures, the magnetic susceptibility of UPd[sub 2]Si[sub 2] is Curie-Wiess-like along the [ital c] axis. The temperature dependence of the Hall coefficient above 108 K is accounted for by a theoretical model invoking skew scattering of conduction electrons by localized magnetic moments.
The existence of a cosmic neutrino background - the analogue of the cosmic microwave background - is a fundamental prediction of standard big bang cosmology. Up to now, the observational evidence for its existence is rather indirect and rests entirely on cosmological observations of, e.g., the light elemental abundances, the anisotropies in the cosmic microwave background, and the large scale distribution of matter. Here, we review more direct, weak interaction based detection techniques for the cosmic neutrino background in the present epoch and in our local neighbourhood. We show that, with current technology, all proposals are still off by some orders of magnitude in sensitivity to lead to a guaranteed detection of the relic neutrinos. The most promising laboratory search, based on neutrino capture on beta decaying nuclei, may be done in future experiments designed to measure the neutrino mass through decay kinematics. (orig.)
The dual characteristics in the performance of polymers in wood-polymer composites systems have been pursued with regard to the resolution of mechanical anisotropy of wood and the improvement in dimensional stability. The objective of the present study is to pursue the polymerization mechanism in wood under electron beam irradiation and the temperature dependence of polymer-wood interactions induced at various levels of higher order structure of wood in order to understand the polymer performance. Veneers used in the study were of rotary-cut beech (Fagus crenata Blume) 0.65 mm thick. All samples were oven-dried in vacuo at 80/sup 0/C for 30 hr. The monomers used in the study were methyl methacrylate, styrene, acrylic acid, acrylonitrile, and unsaturated polyester. Experimental details are given. Results are given and discussed.
The full theory and the semiclassical description of loop quantum cosmology (LQC) have been studied in the Friedmann-Robertson-Walker and Bianchi I models. As an extension to include both anisotropy and intrinsic curvature, this paper investigates the cosmological model of Kantowski-Sachs spacetime with a free massless scalar field at the level of phenomenological dynamics with the LQC discreteness corrections. The LQC corrections are implemented in two different improved quantization schemes. In both schemes, the big bang and big crunch singularities of the classical solution are resolved and replaced by the big bounces when the area or volume scale factor approaches the critical values in the Planck regime measured by the reference of the scalar field momentum. Symmetries of scaling are also noted and suggest that the fundamental spatial scale (area gap) may give rise to a temporal scale. The bouncing scenarios are in an analogous fashion of the Bianchi I model, ...
Highly ordered arrays of Ni nanoholes and Fe{sub 20}Ni{sub 80} antidots have been prepared, respectively, by replica/antireplica processing and sputtering techniques using nanoporous alumina membranes as templates. Geometrical characteristics as nanohole/antidot diameter, interpore distance and the overall hexagonal symmetry of arrays are controlled through the original templates. Experimental data on their hysteresis and magnetic domain structure have been taken by vibrating sample magnetometry and magnetic force microscopy, respectively. An analysis of the magnetization process, resulting magnetic anisotropy and magnetic domain structure is summarized considering the influence of those geometry aspects. In particular, the hexagonal symmetry and the density of nanohole/antidots determine the overall magnetic behavior, which is of interest in future high-density magnetic storage systems.
Highly ordered arrays of Ni nanoholes and Fe20Ni80 antidots have been prepared, respectively, by replica/antireplica processing and sputtering techniques using nanoporous alumina membranes as templates. Geometrical characteristics as nanohole/antidot diameter, interpore distance and the overall hexagonal symmetry of arrays are controlled through the original templates. Experimental data on their hysteresis and magnetic domain structure have been taken by vibrating sample magnetometry and magnetic force microscopy, respectively. An analysis of the magnetization process, resulting magnetic anisotropy and magnetic domain structure is summarized considering the influence of those geometry aspects. In particular, the hexagonal symmetry and the density of nanohole/antidots determine the overall magnetic behavior, which is of interest in future high-density magnetic storage systems.
Time-differential magnetic moment measurements on the first-excited Isup(#pi#)=2"+ states in "2"0Ne and "2"4Mg with mean lives of 1.0 and 2.1 ps, respectively are described. The lifetime of the latter state was determined simultaneously. A special detection geometry was designed to improve the experimental #gamma#-ray anisotropy measured with finite-size detectors. For "2"0Ne also a time-integral measurement with charge-state separation was performed. The necessary electronics circuitry built to perform these complicated measurements and the plunger assembly with laser interferometer are also described. A magnetic moment measurement of "2"2Ne(2_1"+) with tau=5.0 ps and transient field measurements at low and high recoil velocities are reported. A discussion of possible extensions of the techniques are given. (Auth.).
New phosphates with NaZr{sub 2}(PO{sub 4}){sub 3} structure of the B{sub 0.5}FeTa(PO{sub 4}){sub 3}-type (where B-Ca, Sr, Ba) are synthesized and characterized by X-ray diffraction analysis and IR-spectroscopy. The heating behavior of the phosphates is studied using high-temperature X-ray crystallography in the range 15-625 deg. C. The unit-cell parameters, the coefficients of thermal expansion {alpha}{sub a}, {alpha}{sub c} and their thermal expansion anisotropy |{alpha}{sub c} - {alpha}{sub a}| of the phosphates under study are determined and the dependences of these characteristics on the nature of cations are established and analyzed.
The temperature dependence of the average magnetization direction in an Fe_8_0B_2_0 glassy alloy (METGLAS 2605) is investigated by Moessbauer spectroscopy. Moessbauer spectra were recorded between 77 K and 363 K using a conventional constant-acceleration Moessbauer spectrometer with 10 mCi "5"7Co in Pd source. The direction of the easy magnetization is found to be strongly terperature dependent and the out-of-plane component turned to be unusually large. Comparing the magnetic moments some similarities between the electronic structure of the glassy alloy and the Fe_2B and FeB intermetallic compounds are established and discussed. (Sz.N.Z.).
We compare the effect of isotropic point defects vis a vis extended defects on the inter and intra grain properties of superconducting MgB{sub 2} thin films. In a recent paper Gandikota et al. [Appl. Phys. Lett. 86 (2005) 012508] reported that after 200 MeV {alpha} particle irradiation intergrain connectivity remains unaffected. Our results on the contrary indicate that connectivity does depend on irradiation dose and type of ions used. We ascertain that extended defects alter the {sigma} band properties of this two-band superconductor more effectively than the point defects. The improvement in upper critical field and critical current density is intricately related to the type and density of defects created.
The microstructure and tensile properties of Ti-44Al-6V-3Nb-0.3Y (at.%) alloy after canned forging were investigated. SEM results showed that the TiAl pancake exhibits inhomogeneous microstructure, which can be ascribed to the temperature drop and friction between billet and outer pack during forging, as well as the intrinsic anisotropy of lamellar colony. By means of TEM observation and EBSD analysis, the microstructure in the dominant area of the pancake was further characterized. This deformation area consists of 87.7% content of g grains plus some refined lamellar colonies and the rest of B2 grains. The grain size ranges between 1mm and 8.5mm. High-angle boundaries dominate the deformation microstructure, several substructures and twins are observed as well. Additionally, current forge...
Examinations of polished and dry cut sections of feed and tuyere coke revealed some possible mechanisms for the physical influence of mineral compounds on the reactivity and strength of coke. It was observed that rounded particles of mineral phases that are exposed to the pore walls and surface of coke at high temperature create an inorganic cover, thus reducing the surface available for gas-solid reactions. The particles of mineral matter that have a low melting point and viscosity can affect the coke at earlier stages in the blast furnace process, acting in the upper parts of the blast furnace (BF). The temperature-driven redistribution of mineral phases within the coke matrix probably leads to the creation of weak spots and in general to anisotropy in its properties, thus reducing its strength. 9 refs., 2 figs., 1 tab.
Samples of Fe78B13Si9 (Metglas 2605 TCA) and Fe77Cr2B16Si5 (Metglas 2605 S3A) were exposed to pulsed excimer laser irradiation at repetition rates of 15, 25 and 50Hz. The occurrence of out-of-plane magnetic anisotropy, changes in the average hyperfine magnetic field and width of the hyperfine field distribution were evidenced by transmission Mossbauer spectroscopy. The variation of the recoilless fraction with laser processing parameters was derived from the simultaneous recording of Mossbauer spectra using a stainless steel etalon as a dual absorber. Conclusions on the onset of long-range magnetic order were formulated.
Magnetic properties of Fe-Co-Mo-Cu-B alloy system with Co up to 26at.% were investigated. After proper thermal treatment, the nanocrystalline grain remains tiny, the density hardly increases, but the room-temperature saturation attains 1.5T mainly due to a high enough Curie temperature. The generally observed slant hysteresis loops point to ribbon surfaces, which stress the ribbon interior and induce a specific magnetoelastic contribution to hard-ribbon-axis magnetic anisotropy even after vacuum annealing. The effect does not come from cobalt but rather from the lack of silicon. Partial removal of the surfaces resulted in a decrease of the loop tilt.
The switching behavior of magnetic patterns prepared by ion irradiation was investigated. Co/Pt multilayers with perpendicular anisotropy and large out-of-plane coercivities 5-6 kOe were grown on electron transparent SiN windows. Regularly spaced 1 micron sized regions, were magnetically pattered via ion beam irradiation through a stencil mask. Lorentz TEM was used to observe in-situ magnetization reversal processes of irradiated regions under well-defined applied magnetic fields. When the in-plane field was increased, domain wall motion was observed, resulting in the alignment of the patterns with the direction of the applied field. The switching mechanism of the in-plane patterns was by domain wall motion.
We calculate the quarkonium dissociation rate in the P and CP-odd domains (bubbles) that were possibly created in heavy-ion collisions. In the presence of the magnetic field produced by the valence quarks of colliding ions, parity-odd domains generate electric field. Quarkonium dissociation is the result of quantum tunneling of quark or antiquark through the potential barrier in this electric field. The strength of the electric field in the quarkonium comoving frame depends on the quarkonium velocity with respect to the background magnetic field. We investigate momentum, electric field strength and azimuthal dependence of the dissociation rate. Azimuthal distribution of quarkonia surviving in the electromagnetic field is strongly anisotropic; the form of anisotropy depends on the relation between the electric and magnetic fields and quarkonium momentum. These features can be used to explore the properties of the electromagnetic field created in heavy ion ...
During helium beam fuelling experiments in JET, distinctive anisotropic features have been observed in the velocity distribution function describing both fast and thermal alpha particle populations. During the initial fuelling phase the central helium ion temperature observed perpendicular to the magnetic field is higher than the central electron temperature, while the central helium ion temperature observed parallel to the magnetic field is lower than or equal to the central electron temperature. In order to verify temperature measurements of both perpendicular and parallel lines of sight, other independent methods of deducing the ion temperature are investigated: deuterium ion temperature, deuterium density, comparison with neutron rates and profiles (influence of a possible metastable population of helium). 6 refs., 7 figs.
A variety of observations suggest that the Universe had a hot dense origin and that the pregalactic composition of the Universe was determined by nuclear reactions that occurred in the first few minutes. There is no unique hot Big Bang theory, but the simplest version produces a primeval chemical composition that is in good qualitative agreement with the abundances deduced from observation. Whether or not any Big Bang theory will provide quantitative agreement with observations depends on a variety of factors in elementary particle physics (number and masses of stable or long-lived particles, half-life of neutron, structure of grand unified theories) and from observational astronomy (present mean baryon density of the Universe, the Hubble constant and deceleration parameter). The influence of these factors on the abundances is discussed, as is the effect of departures from homogeneity and isotropy in the early Universe.
Algorithms for generating new exact solutions of the Einstein-Klein-Gordon field equations, which describe inhomogeneous universes with S/sup 3/ topology of spatial sections, are developed. The known exact vacuum and still-fluid solutions with S/sup 3/ topology are used as an input. The methods developed are further applied to derive inhomogeneous generalizations of Bianchi type IX solutions and inhomogeneous S/sup 3/ Gowdy models with gravitational and scalar waves. It is shown that the new solutions, which are generalizations of the Bianchi type IX models, permit identification of the scalar field with the velocity potential of the stiff irrotational fluid. The latter result is further used to study the growth rate of density perturbations of the isotropic and anisotropic Bianchi type IX universes in a fully nonlinear relativistic regime. The role of anisotropy on the rate of growth of density perturbations is studied in detail.
Algorithms for generating new exact solutions of the Einstein-Klein-Gordon field equations, which describe inhomogeneous universes with S"3 topology of spatial sections, are developed. The known exact vacuum and still-fluid solutions with S"3 topology are used as an input. The methods developed are further applied to derive inhomogeneous generalizations of Bianchi type IX solutions and inhomogeneous S"3 Gowdy models with gravitational and scalar waves. It is shown that the new solutions, which are generalizations of the Bianchi type IX models, permit identification of the scalar field with the velocity potential of the stiff irrotational fluid. The latter result is further used to study the growth rate of density perturbations of the isotropic and anisotropic Bianchi type IX universes in a fully nonlinear relativistic regime. The role of anisotropy on the rate of growth of density perturbations is studied in detail.
Cfiber/Si3N4 composites were prepared by hot-pressed sintering using a-Si3N4 powders, short carbon fibers and sintering additives as starting materials. The mechanical and dielectric properties of these composites were studied. When the short carbon fiber content of the composites increases from 0 to 1wt.%, the fracture toughness increases from 3.456 to 4.203MPam1/2, and both the real and imaginary part of permittivity increase greatly over the frequency range 8.2-12.4GHz. These effects were due to the anisotropy of short carbon fibers.
ABSTRACT New observations from the Hubble Ultra Deep Field suggest that the star formation rate at Formula Not Shown drops off faster than previously thought. Using a newly determined star formation rate for the normal mode of Population II/I (PopII/I) stars, including this new constraint, we compute the Thomson scattering optical depth and find a result that is marginally consistent with Wilkinson Microwave Anisotropy Probe 5 results. We also reconsider the role of Population III (PopIII) stars in light of cosmological and stellar evolution constraints. While this input may be needed for reionization, we show that it is essential in order to account for cosmic chemical evolution in the early universe. We investigate the consequences of PopIII stars on the local metallicity distribution fu...
The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic slip systems.
Stellar rotation velocities and velocity dispersions along three slit positions in M31 have been measured, and three-dimensional velocity and velocity dispersion fields are obtained in order to search for a central black hole. Synthetic apparent spectra are constructed to eliminate problems with the reaction of the Fourier quotient program to stellar population mixes. Models are constructed to explore parameter space. The large velocities and velocity gradients that are found imply that the total mass-to-light ratio rises sharply at r of 0.5 arcsec or less to values greater than 100. This is much larger than normal for old stellar populations. Velocity anisotropies are not a major uncertainty because of the rapid rotation. There is thus strong evidence for a dark central mass, probably a supermassive black hole. 48 references.
The standard Friedmann-Robertson-Walker (FRW) big bang model of the universe requires special initial conditions: the early universe is highly homogeneous and isotropic even though there exist causally disconnected regions (horizon problem). A plane symmetric (anisotropic) solution of field equations in a generalized theory of gravitation predicts the beginning of the universe as a vacuum instability at a specific fundamental time (which can be associated with the Planck time (tsub(p))), after which matter is created as the universe begins to expand. At a time t=tsub(c) there is a singular expansion, the anisotropy vanishes, and the physical horizon becomes infinite. Thereafter the solution of the field equations goes over into the FRW model. Thus the special initial conditions of the FRW model at the big bang singularity t=tsub(c) are predicted by the theory.
Objective: To compare pediatric patients with periventricular leukomalacia (PVL) with normal children by using diffusion tensor MR imaging. Methods: Diffusion tensor images were obtained in 15 pediatric patients with PVL and 15 age-matched normal children. Regions of interest were drawn to measure the fractional anisotropy (FA) in bilateral posterior limb of internal capsule, bilateral optic radiation, genu of corpus callosum, and splenium of corpus callosum. The values of PVL patients and normal children were compared using non-dependent samples T-test. Results: The FA values of regions of interest prescribed were significantly lower in PVL patients than in normal children (P<0.01). Conclusion: Diffusion tensor imaging may reveal retard of myelination of fiber tracts in PVL patients. It can be a potential tool in evaluating the brain development of children. (authors)
The next decade promises an observational revolution which will change cosmology forever. The precise measurement of the angular anisotropy of the cosmic microwave background should specify to a few percent all of the parameters of the cosmological model which effect astrophysics. The growth of structure will then be determined (but not yet observed) until gravitational collapse becomes highly non-linear and stars, galaxies and active galactic nuclei (AGN) form. These processes are hard to model with basic physics because they are complex and allow a rich variety of expression. Instead observations will determine when the first stars and quasars formed, and how and when galaxies assembled. If we can reconcile the numerous contradictions which characterize the subject today, cosmology will become a mature subject, founded on the agreement between detailed, inclusive and realistic models, which make precise predictions, and the wealth of new data which will come from ...
The dynamical effects of spatially homogeneous electromagnetic fields on anisotropic Bianchi type-IX models are studied. The Lagrangians and Hamiltonians affecting the evolution of anisotropy (including the gravitational and electromagnetic potentials) are obtained for very general spatially homogeneous metrics by means of the Arnowitt-Deser-Misner Hamiltonian formalism. For models having diagonal metrics an exact solution for the electromagnetic fields is obtained. This solution allows a qualitative solution for the gravitational variables. The total solution is similar to that of Brill. For Bianchi type-IX models having symmetric and general metrics, a discussion of the qualitative behavior of the universe point under the influence of the above potentials is given. In particular, it is shown that in some cases the presence of the electromagnetic potential inhibits some types of singularities.
The dynamical effects of spatially homogeneous electromagnetic fields on anisotropic Bianchi type-IX models are studied. The Lagrangians and Hamiltonians affecting the evolution of anisotropy (including the gravitational and electromagnetic potentials) are obtained for very general spatially homogeneous metrics by means of the Arnowitt-Deser-Misner Hamiltonian formalism. For models having diagonal metrics an exact solution for the electromagnetic fields is obtained. This solution allows a qualitative solution for the gravitational variables. The total solution is similar to that of Brill. For Bianchi type-IX models having symmetric and general metrics, a discussion of the qualitative behavior of the universe point under the influence of the above potentials is given. In particular, it is shown that in some cases the presence of the electromagnetic potential inhibits some types of singularities.
AZ31 Mg alloy samples were extruded by an equal channel angular extrusion (ECAE) process and subsequently annealed to obtain fine-grained material with a low dislocation density. Tensile tests at room temperature exhibited an apparent steady-state deformation region and a large tensile elongation of 47%. The deformed microstructure at an elongation of 2% indicated a substantial cross-slip to nonbasal planes possibly induced by grain-boundary compatibility effects. The nonbasal segments of dislocations were found to consist of 40% of the total dislocation density at a yield anisotropy factor of only 1.1 instead of an expected value of 100 from single-crystal experiments. (orig.)
VHF wind-profiling radars often measure a decrease of echo power with zenith angle, which can be explained from in situ measurements of horizontal layering or anisotropy of metre-scale temperature structure in the atmosphere. There can also be an azimuthal variation of echo power, which is increased in an azimuth opposite to the vertical shear vector of horizontal wind. This paper checks if the azimuth variation can also be linked to in situ observations of temperature structure, using aircraft flights in the tropopause region near a VHF radar. At heights where VHF radar measures wind shear and aspect sensitivity, there can be an asymmetry in the probability distribution of horizontal gradient of potential temperature, for horizontal scale of e.g. hundreds of metres. The asymmetry is often...
Radial sonic crystals (RSC) are fluidlike structures infinitely periodic along the radial direction that verify the Bloch theorem and are possible only if certain specially designed acoustic metamaterials with mass density anisotropy can be engineered (see Torrent and Sanchez-Dehesa 2009 Phys. Rev. Lett. 103 064301). A comprehensive analysis of two-dimensional (2D) RSC shells is reported here. A given shell is in fact a circular slab with a central cavity. These finite crystal structures contain Fabry-Perot-like resonances and modes strongly localized at the central cavity. Semi-analytical expressions are developed to obtain the quality factors of the different resonances, their symmetry features and their excitation properties. The results reported here are completely general and can be extended to equivalent 3D spherical shells and to their photonic counterparts.
This paper presents a patient specific deformable heart model that involves the known electrical and mechanical properties of the cardiac cells and tissue. The whole heart model comprises ten Tusscher's ventricular and Nygren's atrial cell models, the anatomical and electrophysiological model descriptions of the atria (introduced by Harrild et al.) and ventricle (given by Winslow et al.), and the mechanical model of the periodical cardiac contraction and resting phenomena proposed by Moireau et al. During the propagation of the depolarization wave, the kinetic, compositional and rotational anisotropy is handled by the tissue, organ and torso model. The applied patient specific parameters were determined by an evolutionary computation method. An intensive parameter reduction was performed u...
The in-plane resistivity, in-plane absolute thermopower, and upper critical field measurements are reported for single-crystal samples of YNi_2B_2C and LuNi_2B_2C superconductors. The in-plane resistivity shows metallic behavior and varies approximately linearly with temperature near room temperature (RT) but shows nearly quadratic behavior in temperature at low temperatures. The YNi_2B_2C and LuNi_2B_2C single-crystal samples exhibit large transverse magnetoresistance (#approx#6 8% at 45 kOe) in the ab plane. The absolute thermopower S(T) is negative from RT to the superconducting transition temperature T_c. Its magnitude at RT is a few times of the value for a typical good metal. S(T) is approximately linear in temperature between #approx#150 K and RT. Extrapolation to T=0 gives large intercepts (few #mu#V/K) for both samples suggesting the presence of a much larger knee than would be expected from electron-phonon interaction renormalization effects. The upper critical fields for H ...
Stellar rotation and velocity-dispersion measurements are presented for the bulge components of the SBO galaxies NGC 1023, 2859, 2950, 4340, 4371, and 7743. The kinematics of nine SB bulges with data available are compared with bulges of unbarred galaxies studied by Kormendy and Illingworth. All of the SB bulges are found to rotate at least as rapidly as oblate-spheroid dynamical models which are flattened by rotation. This result confirms the conclusion of Kormendy and Illingworth that bulges rotate very rapidly. Six SB bulges found by Kormendy and Koo to be triaxial rotate even more rapidly than the oblate models. In this respect, they resemble published n-body models of bars. That is, triaxial bulges are dynamically like bars and unlike elliptical galaxies, which are also believed to be triaxial, but which rotate slowly. Measured velocity anisotropies are found to be consistent with these conclusions. Two ordinary bulges whose rotation is well described by ...
The productivity characteristics of perforated gas well are investigated for the first time under real conditions considering drilling damage, perforation compacted zone and anisotropy in this paper. A non-linear finite element model for non-Darcy flow in perforated gas reservoir is built to consider the effects of twelve factors on productivity ratio (PR) of perforated gas well. The nomographs for two cases are presented in this paper. Compared with previous works, the following results are found: (1) the effects of drilling damage and perforation diameter on PR of gas well are more remarkable than that in oil well; (2) any perforation phase may be the best or the worst as to perforating gas well, which depends on anisotropy, drawdown and that whether or not perforations are beyond drilling damage zone; (3) the increase in perforation length hardly improve PR of gas well when perforations have been beyond drilling damage zone. The new method ...
As the only non-polar plane the (110) surface has a unique role in GaAs. Together with Silicon as a dopant it is an important substrate orientation for the growth of n-type or p-type heterostructures. As a consequence, this thesis will concentrate on growth and research on that surface. In the course of this work we were able to realize two-dimensional electron systems with the highest mobilities reported so far on this orientation. Therefore, we review the necessary growth conditions and the accompanying molecular process. The two-dimensional electron systems allowed the study of a new, intriguing transport anisotropy not explained by current theory. Moreover, we were the first growing a two-dimensional hole gas on (110) GaAs with Si as dopant. For this purpose we invented a new growth modulation technique necessary to retrieve high mobility systems. In addition, we discovered and studied the metal-insulator transition in thin bulk p-type layers on (110) GaAs. ...
The energy strategy of the UK Overseas Development Administration is outlined with specific emphasis on energy efficiency and renewable energies. Based on 29 case studies concerning projects and programmes in both developed and developing countries, critical success factors for renewable energy projects are identified. UK)
The Monthly Energy Review provides an overview of the production, distribution, and consumption of energy derived from petroleum natural gas, coal, electricity, and nuclear energy. It also discusses oil and gas resource development, energy prices, and issues relevant to international energy markets.
A survey on electric power and on energy balance especially primary and final energy (gas oil, kerosene,solar energy...) has been implemented in Lebanon in 1993. Results and economic impact of energy consumption and energy production are given in statistics and tables. 10 figs.
The article describes the energy in Lebanon. In 1995, 97% of the imported energy was based on hydrocarbons. Fuel and gas oil present 66% of the final energy. Air pollution is mainly caused by the transportation sector (vehicles and buses...) which presents 70% of the global atmospheric pollution. Renewable energy such as biomass, fossil energy, hydro-energy, solar energy... are also described. The solar energy was defined as a best solution that preserve health in Lebanon. The different applications of the solar for energy production is discussed: photovoltaic , thermal heating, sanitary hot water, electrical heaters, solar water heaters...In conclusion, solar heaters economize 80% of the annual energy expenses
Jet Propulsion Laboratory. California Institute of Technology. Pasadena, California. Energy and Water Conservation. Steve Rigdon. Facilities Energy Manager ...
... is to develop a systematic program of energy consumption reductions in compliance with the stated goals of the Army Facilities Energy Plan (AFEP ...
... projects that will result in the reduction of energy consumption in compliance with the objectives set forth in the Army Facilities Energy Plan, without ...
Superparamagnetic MFe{sub 2}{sup 3+}O{sub 4} (M=Mn{sup 2+}, Fe{sup 2+} and Co{sup 2+}) inverse spinel ferrite (ISF) nanoparticles with narrow size distribution having average diameters of 6-8 nm were synthesized by a diol reduction of organic metals and the surface was modified to be hydrophilic by coating with succimer. Magnetic resonance imaging (MRI) contrast enhancement by dipolar coupling defined interactions between the synthesized ISFs and protons in the bulk water was investigated with initial susceptibility, magnetization and anisotropy of the succimer-coated ISFs. The relaxivity ratios, r{sub 2}/r{sub 1}, for MnFe{sub 2}O{sub 4}, Fe{sub 3}O{sub 4} and CoFe{sub 2}O{sub 4} were measured to be 12.2, 23.1 and 62.3, respectively, which demonstrate the potential usefulness of these magnetic nanoparticles as T{sub 2} contrast agents for MRI.
The collapse of a massive star's core, followed by a neutrino-driven, asymmetric supernova explosion, can naturally lead to pulsar recoils and neutron star kicks. Here, we present a two-dimensional, radiation-hydrodynamic simulation in which core collapse leads to significant acceleration of a fully-formed, nascent neutron star (NS) via an induced, neutrino-driven explosion. During the explosion, a ~10% anisotropy in the low-mass, high-velocity ejecta lead to recoil of the high-mass neutron star. At the end of our simulation, the NS has achieved a velocity of ~150 km s$^{-1}$ and is accelerating at ~350 km s$^{-2}$, but has yet to reach the ballistic regime. The recoil is due almost entirely to hydrodynamical processes, with anisotropic neutrino emission contributing less than 2% to the overall kick magnitude. Since the observed distribution of neutron star kick velocities peaks at ~300-400 km s$^{-1}$, recoil due to anisotropic core-collapse supernovae provides a ...
Superparamagnetic MFe23+O4 (M=Mn2+, Fe2+ and Co2+) inverse spinel ferrite (ISF) nanoparticles with narrow size distribution having average diameters of 6-8 nm were synthesized by a diol reduction of organic metals and the surface was modified to be hydrophilic by coating with succimer. Magnetic resonance imaging (MRI) contrast enhancement by dipolar coupling defined interactions between the synthesized ISFs and protons in the bulk water was investigated with initial susceptibility, magnetization and anisotropy of the succimer-coated ISFs. The relaxivity ratios, r2/r1, for MnFe2O4, Fe3O4 and CoFe2O4 were measured to be 12.2, 23.1 and 62.3, respectively, which demonstrate the potential usefulness of these magnetic nanoparticles as T2 contrast agents for MRI.
The temperature dependence of T/sub 1/ spin-lattice relaxation time on /sup 51/V, /sup 69/Ga, /sup 71/Ga and Knight shift on /sup 51/V and /sup 29/Si nuclei in polycrystalline V/sub 3/Si, V/sub 3/Ga, V/sub 3/Ge and in the monocrystal V/sub 3/Si in normal state is investigated. For V/sub 3/Si and V/sub 3/Ga a rapid growth (T/sub 1/T)/sup -1/ is observed with temperature decrease while for V/sub 3/Ge the maximum (T/sub 1/T)/sup -1/ at T approximately equal to 60 K has been found. The temperature dependence peculiarities have been discussed on the basis of theoretical models available and zone structure calculations for A-15 compounds. The T/sub 1/ anisotropy and possibility of its experimental discovery are considered. Anisotropic contribution in (T/sub 1/T)/sup -1/ and contributions of d states of different symmetries into the electron state density at the Fermi level are estimated for V/sub 3/Si from T/sub 1/ measurements.
The temperature dependence of T_1 spin-lattice relaxation time on "5"1V, "6"9Ga, "7"1Ga and Knight shift on "5"1V and "2"9Si nuclei in polycrystalline V_3Si, V_3Ga, V_3Ge and in the monocrystal V_3Si in normal state is investigated. For V_3Si and V_3Ga a rapid growth (T_1T)"-"1 is observed with temperature decrease while for V_3Ge the maximum (T_1T)"-"1 at T approximately equal to 60 K has been found. The temperature dependence peculiarities have been discussed on the basis of theoretical models available and zone structure calculations for A-15 compounds. The T_1 anisotropy and possibility of its experimental discovery are considered. Anisotropic contribution in (T_1T)"-"1 and contributions of d states of different symmetries into the electron state density at the Fermi level are estimated for V_3Si from T_1 measurements.
The measurement of the brightness temperature fluctuations of neutral hydrogen 21 cm lines from the Epoch of Reionisation (EoR) is expected to be a powerful tool for revealing the reionisation process. We study the 21 cm cross-correlation with Cosmic Microwave Background (CMB) temperature anisotropies, focusing on the effect of the patchy reionisation. We calculate, up to second order, the angular power spectrum of the cross-correlation between 21 cm fluctuations and the CMB kinetic Sunyaev-Zel'dovich effect (kSZ) from the EoR, using an analytical reionisation model. We show that the kSZ and the 21 cm fluctuations are anti-correlated on the scale corresponding to the typical size of an ionised bubble at the observed redshift of the 21 cm fluctuations. The amplitude of the angular power spectrum of the cross-correlation depends on the fluctuations of the ionised fraction. Especially, in a highly inhomogeneous reionisation model, the amplitude reaches the order of ...
Observations of anisotropies in the brightness temperature of the 21 cm line of neutral hydrogen from the period before reionization would shed light on the dawn of the first stars and galaxies. In this paper, we use large-scale semi-numerical simulations to analyse the imprint on the 21 cm signal of spatial fluctuations in the Lyman-alpha flux arising from the clustering of the first galaxies. We show that an experiment like the Square Kilometer Array (SKA) can probe this signal at the onset of reionization giving us important information about the UV emission spectra of the first stars and characterizing their host galaxies. SKA-pathfinders with ~ 10% of the full collecting area should be capable of making a statistical detection of the 21 cm power spectrum at redshifts $z\\lesssim 20$. We then show that the SKA should be able to measure the three dimensional power spectrum as a function of the angle with the line of sight and discuss the use of the redshift ...
The PLANCK SURVEYOR is a European Space Agency satellite mission to image the very faint anisotropies in the temperature of the Cosmic Microwave Background (CMB) radiation. Maynooth is actively participating in an international collaboration of scientists involved with the optical design of the High Frequency Instrument (HFI). This paper outlines research which has been undertaken in Maynooth concerned with numerical modelling of the optical characteristics of the multi-frequency array of detectors making up the HFI instrument. In the study the commercial software package ZEMAX was used to model the coupling of the focal plane HFI detectors to the PLANCK telescope. This package is particularly useful in the optical design of PLANCK because of the powerful optimisation features of the software. It is thus possible to readily determine the optimum positioning of the detectors in the focal plane of the telescope. Although the package is based on a numerical ray ...
Deformation mechanisms were investigated in fine-grain (d=7 {mu}m) AZ31 Mg alloy in order to understand their excellent room-temperature ductility. Dislocation cross slip from basal to non-basal planes was found to occur easily at room temperature at a plastic anisotropy factor of only 1.5 instead of several tens to 100 expected from the single crystal CRSS data. Enhanced grain-boundary sliding (GBS) was also found to occur at room temperature. The contribution of GBS strain was found to be approximately 8% of total strain. The enhanced activity of non-basal dislocation slip and GBS was attributed to grain-boundary compatibility effects. Moreover, dynamic recovery was found to occur during deformation at room temperature associated with the formation of recovery twins and small-angle grain boundaries. The occurrence of these deformation mechanisms at room temperature was considered to be a major reason for an excellent ductility in fine-grain Mg alloys. (orig.)
The extraction of cosmological parameters from microwave background observations relies on specific assumptions about the statistical properties of the data, in particular that the p-point distributions of temperature fluctuations are jointly-normal. Using a battery of statistical tests, we assess the multivariate Gaussian nature of the Wilkinson Microwave Anisotropy Probe (WMAP) 1st year data. The statistics we use fall into three classes which test different aspects of joint-normality: the first set assess the normality of marginal (one-point) distributions using familiar univariate methods; the second involves statistics that directly assess joint-normality; and the third explores the evidence of non-linearity in the relationship between variates. We applied these tests to frequency maps, `foreground-cleaned' assembly maps and all-sky CMB-only maps. The assembly maps are of particular interest as when combined with the kp2 mask, we recreate the region used in ...
Nanocrystalline Fe75Si20M5 (M = Al, B and Cr) powders were synthesized by mechanical alloying in a planetary ball mill from high purity elemental powders. Evolution of non-equilibrium solid solutions of ?-Fe[Si,(Al, B, Cr)] with a nanocrystalline structure was accompanied by the introduction of a large number of dislocation defects in the course of the milling process. Fe sites get substituted by Si and M (M = Al, B, Cr) atoms during the milling process. The structural change and the resulting disorder are reflected in the changes in the lattice parameter and average magnetic moment of the powders milled for various time periods. The effective magnetic anisotropy increases linearly with the milling time. An increase in coercivity with increasing milling time was observed which could be attributed to the introduction of dislocations and the reduction in the powder particle size during milling. The presence of dislocations and grain boundaries increases the ...
The magnetic properties of a single crystal of SmNiSn with the orthorhombic {epsilon}-TiNiSi-type crystal structure have been investigated by magnetic susceptibility, magnetization and electrical resistivity measurements from 1.5 K to room temperature. Two anomalies have been found in the magnetic susceptibility, indicating an antiferromagnetic phase transition at T{sub N}=9.4 K and a second transition at 4.4 K. A large magnetic anisotropy has been found at low temperatures in the temperature and field dependencies of magnetic susceptibility and magnetization. Below 80 K, the easy axis of the magnetization is the c-axis. At T=2.0 K, the c-axis magnetization curve exhibits metamagnetic-like behavior at H{sub c}=42 kOe and reaches 0.54 emu/g at H=55 kOe, whereas for the a- and b-axis the magnetization is linear and smaller. The paramagnetic susceptibilities do not follow the Curie-Weiss law suggesting a large van Vleck contribution of the Sm ions.
Ternary R_2TSi_3 intermetallic compounds (R=Rare Earth, T=Transition Metal) with hexagonal AlB_2-type crystallographic structure are known because of their interesting physical properties. Pr_2PdSi_3 single crystals were grown by a vertical floating zone method. The compound exhibits congruent melting behavior at a liquidus temperature of about 1770 C. Single crystalline samples show a huge anisotropy at low temperatures due to the crystal electric field effect and order antiferromagnetically below the Neel temperature T_N=2.17 K. This value approximately obeys the linear de Gennes scaling for this class of compounds. The [001] orientation was identified as the magnetic easy axis at room temperature. At lower temperature (#approx#20 K) magnetic easy and hard axes interchange with each other. Two additional magnetic phase transitions were observed at temperatures below 1 K.
The three-dimensional magnetic structure and reversal mechanism of patterned Co/Pt multilayers, were imaged using complementary Lorentz transmission electron microscopy (LTEM) (in-plane component) and magnetic transmission x-ray microscopy (M-TXM) (perpendicular magnetization). The Co/Pt films with perpendicular anisotropy were patterned by ion irradiation through a stencil mask to produce in-plane magnetization in the irradiated regions. The boundaries of the patterns, defined by the transition from out-of-plane to in-plane magnetization, were found to be determined by the stencil mask, whilst the scale of the magnetic reversal by the physical microstructure. The nucleation fields were substantially reduced to 50 Oe for the in-plane regions and 1 kOe for the perpendicular regions, comparing to 4.5 kOe for the as-grown film. The perpendicular reversals were found to always originate at the pattern boundaries.
Constraints on the original Cardassian model and the modified polytropic Cardassian model are examined from the latest derived 397 Type Ia supernova (SNe Ia) data, the size of baryonic acoustic oscillation peak from the Sloan Digital Sky Survey (SDSS), the position of first acoustic peak of the Cosmic Microwave Background radiation (CMB) from the five years Wilkinson Microwave Anisotropy Probe (WMAP), the x-ray gas mass fractions in clusters of galaxies, and the observational H(z) data. In the original Cardassian model with these combined data set, we find $\\Omega_{m0}=0.271^{+0.014}_{-0.014}, n=0.035^{+0.049}_{-0.049}$ at $1 \\sigma$ confidence level. And in the modified polytropic Cardassian model, we find that $\\Omega_{m0}=0.271^{+0.014}_{-0.015}$, $n=-0.091^{+0.331}_{-1.908}$ and $\\beta=0.824^{+0.750}_{-0.622}$ within $1\\sigma$ confidence level. According to these observations, the acceleration of the universe begins at $z_T=0.55^{+0.05}_{-0.05} (1\\sigma)$ ...
A micro-mechanistic understanding of bone fracture that encompasses how cracks interact with the underlying microstructure and defines their local failure mode is lacking, despite extensive research on the response of bone to a variety of factors like aging, loading, and/or disease. Micro-mechanical models for fracture incorporating such local failure criteria have been widely developed for metallic and ceramic materials systems; however, few such deliberations have been undertaken for the fracture of bone. In fact, although the fracture event in mineralized tissues such as bone is commonly believed to be locally strain controlled, until recently there has been little experimental evidence to support this widely held belief. In the present study, a series of in vitro experiments involving a double-notch bend test geometry are performed in order to shed further light on the nature of the local cracking events that precede catastrophic fracture in bone and to define their relationship to ...
We present a new class of exact solutions of Deser, Jackiw, and Templeton's theory (DJT) of topologically massive gravity which consists of homogeneous, anisotropic manifolds. In these solutions the coframe is given by the left-invariant 1-forms of 3-dimensional Lie algebras up to constant scale factors. These factors are fixed in terms of the DJT coupling constant {mu}m which is the constant of proportionality between the Einstein and Cotton tensors in 3-dimensions. Differences between the scale factors result in anisotropy which is a common feature of topologically massive 3-manifolds. We have found that only Bianchi Types VI, VIII, and IX lead to nontrivial solutions. Among these, a Bianchi Type IX, squashed 3-sphere solution of the Euclideanized DJT theory has finite action, Bianchi Type VIII, IX solutions can variously be embedded in the de Sitter/anti-de Sitter space. That is, some DJT 3-manifolds that we shall present here can be regarded as the ...
We present a new class of exact solutions of Deser, Jackiw, and Templeton's theory (DJT) of topologically massive gravity which consists of homogeneous, anisotropic manifolds. In these solutions the coframe is given by the left-invariant 1-forms of 3-dimensional Lie algebras up to constant scale factors. These factors are fixed in terms of the DJT coupling constant #mu#m which is the constant of proportionality between the Einstein and Cotton tensors in 3-dimensions. Differences between the scale factors result in anisotropy which is a common feature of topologically massive 3-manifolds. We have found that only Bianchi Types VI, VIII, and IX lead to nontrivial solutions. Among these, a Bianchi Type IX, squashed 3-sphere solution of the Euclideanized DJT theory has finite action, Bianchi Type VIII, IX solutions can variously be embedded in the de Sitter/anti-de Sitter space. That is, some DJT 3-manifolds that we shall present here can be regarded as the basic ...
Anisotropy finite element analysis was performed to study stresses associated with the tetragonal precipitates and the tetragonal to monoclinic transformation in MgO partially stabilized zirconia. Stresses were assumed to be caused by the lattice misfits between the product phase and the parent phase. In the finite element calculations, the tetragonal and monoclinic precipitates were assumed to be lenticular in shape, and the anisotropic elastic constants of the cubic, tetragonal and monoclinic phases were considered. The purpose of this paper is to obtain some knowledge about how stresses respond when the microstructure is changed, and how stress fields affect microstructure development. The finite element results show that increasing a{sub t}/a{sub c} and decreasing c{sub t}/a{sub c} can create a favorable stress field to reduce the growth rate of tetragonal precipitates during the heat treatment. Stresses associated with the single tetragonal precipitate in an ...
A diagrammatic approach to calculate n-point correlators of the primordial curvature perturbation \\zeta was developed a few years ago following the spirit of the Feynman rules in Quantum Field Theory. The methodology is very useful and time-saving, as it is for the case of the Feynman rules in the particle physics context, but, unfortunately, is not very well known by the cosmology community. In the present work, we extend such an approach in order to include not only scalar field perturbations as the generators of \\zeta, but also vector field perturbations. The purpose is twofold: first, we would like the diagrammatic approach (which we would call the Feynman-like rules) to become widespread among the cosmology community; second, we intend to give an easy tool to formulate any correlator of \\zeta for those cases that involve vector field perturbations and that, therefore, may generate prolonged stages of anisotropic expansion and/or important levels of statistical ...
We investigated the isotropic diffusion coefficient (D') and fractional anisotropy (FA) in white matter (WM) during brain development, using an optimised diffusion-tensor imaging (DTI) method with whole brain coverage in a clinically acceptable time. We images 52 children with no evident neurological abnormality (30 boys, 22 girls aged 1 day-16 years) using high-angle DTI with optimised temporal gradient performance. D' and FA were calculated in 10 regions of interest in white matter. We saw that the age-related reduction in D' and increase in FA follow a mono- or biexponential model in white matter, probably depending on the compactness and myelination rate of the fibre tracts. In contrast to other areas, in which adult values were reached during the third year, there is a trend to continuous increase in FA in all deep white-matter areas, suggesting continuing maturation and organisation of deep tracts not detected on conventional MRI. (orig.)
Reactive milling of NiO + Al powder mixture resulted in the formation of NiAl-Al_2O_3 nanocomposite powders, with a crystallite size of about 20 nm. The Hall-Williamson analysis revealed that NiAl showed an orientation dependent crystallite size after short processing time and orientation dependent internal strain after long milling time. Both anisotropies were removed by heating the powders in the differential scanning calorimetry. Calorimetric studies showed one exothermic effect attributed to the reduction reaction of NiO and endothermic one associated with melting of Al. Two methods were applied for powders compaction: resistance sintering and pulse electric discharge. In both cases the densities of abut 90% of the theoretical value were achieved. A significant increase in average NiAl crystallites size in compacted samples was observed, up to several hundreds of nanometers.(author)
We propose a method to determine the cosmic mass density Omega from redshift-space distortions induced by large-scale flows in the presence of nonlinear clustering. Nonlinear structures in redshift space such as fingers of God can contaminate distortions from linear flows on scales as large as several times the small-scale pairwise velocity dispersion sigma_v. Following Peacock & Dodds (1994), we work in the Fourier domain and propose a model to describe the anisotropy in the redshift-space power spectrum; tests with high-resolution numerical data demonstrate that the model is robust for both mass and biased galaxy halos on translinear scales and above. On the basis of this model, we propose an estimator of the linear growth parameter beta = Omega^0.6/b, where b measures bias, derived from sampling functions which are tuned to eliminate distortions from nonlinear clustering. The measure is tested on the numerical data and found to recover the true value of beta ...
Monte Carlo calculations using the codes PENELOPE and GEANT4 have been performed to characterize the dosimetric parameters of the new 20 mm long catheter based $^{32}$P beta source manufactured by Guidant Corporation. The dose distribution along the transverse axis and the two dimensional dose rate table have been calculated. Also, the dose rate at the reference point, the radial dose function and the anisotropy function were evaluated according to the adapted TG-60 formalism for cylindrical sources. PENELOPE and GEANT4 codes were first verified against previous results corresponding to the old 27 mm Guidant $^{32}$P beta source. The dose rate at the reference point for the unsheathed 27 mm source in water was calculated to be $0.215 \\pm 0.001$ cGy s$^{-1}$ mCi$^{-1}$, for PENELOPE, and $0.2312 \\pm 0.0008$ cGy s$^{-1}$ mCi$^{-1}$, for GEANT4. For the unsheathed 20 mm source these values were $0.2908 \\pm 0.0009$ cGy s$^{-1}$ mCi$^{-1}$ and $0.311 \\pm 0.001$ cGy ...
Theoretical work supported by this grant has lead to the concept of the specific pinning force Q and the development of new methods to sum elementary interaction forces to find Q. Pinning due to changes in transition temperature or thermodynamic critical field in thin layers (e.g., a grain boundary), is greatly reduced due to the proximity effect and the stress field interaction due to the dislocations in the grain boundary has been shown to be negligible. The crystalline anisotropy (CA) and electron scattering (ES) interactions have been computed for the first time for an arbitrary boundary. Experiments on niobium bicrystals, polycrystalline niobium thin foils doped with oxygen, lead-bismuth alloy thin films and lead-bismuth alloy films in which either lead or thallium has been allowed to diffuse down the grain boundaries and out into the grains provide evidence that confirms the predictions of the theory. These results suggest that further improvements in grain ...
An approximate expression for whistler-mode group velocity is obtained, taking into account the effects of electron temperature and anisotropy, density and ion effects, effects of oblique propagation and a non-dipolarity of the dayside magnetospheric magnetic field. This expression is applied to the propagation of whistlers between one hemisphere and the other. It is pointed out that at frequencies close to the upper cut-off of whistler spectra, perturbations to whistler group delay times due to temperature effects can be of the same order of magnitude as, or even higher than, the corresponding perturbations due to finite electron density and ion effects. A method of magnetospheric electron temperature diagnostics is proposed and applied to two whistlers recorded at Halley (L = 4.3). It is pointed out that the values of temperature obtained from the analysis of whistler spectra depend on the choice of model of electron density and temperature distribution in the ...
The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was also influenced by the test orientation. Metallographic studies revealed a microstructure which was ...
We present a development of the use of the AAPM TG-43 dose formalism applied to "1"3"7Cs gynecological implant sources. The geometry factor, radial dose function, and anisotropy function of a "1"3"7Cs source modeled after the Nuclear Associates 67-809 series stainless steel jacketed tube source were derived following the AAPM TG-43 formalism. The dose rate distribution through the center of the source using the AAPM TG-43 dose formalism is calculated and compared with the calculations obtained using the Sievert summation and Monte Carlo simulation. The three methods resulted in an agreement within less than 5%, or an isodose rate line agreement within 2 mm. We demonstrate that the AAPM TG-43 formalism can be applied to "1"3"7Cs linear sources and is capable of serving as a "1"3"7Cs dose calculation algorithm that can be used for treatment planning purpose.
We consider the supercooled Stefan problem with a general anisotropic curvature- and velocity-dependent boundary condition on the moving interface. We present numerical methods, based on an integral equation formulation and including a new algorithm for moving curves with curvature-dependent velocity. These methods compute a periodic interface with {ital O}({Delta}{ital t}) accuracy, where {Delta}{ital t} is the time step. Previous work has been limited to short time spans and achieved slightly less than {ital O}({Delta}{ital t}{sup 1/2}) accuracy. Accurate numerical results are seen to agree with the predictions of linear stability theory. This agreement has eluded previous authors, because their numerical methods suffered from grid effects and their linear stability theory was incorrect. We study the long-time evolution of an unstable interface. Our computations exhibit the beginnings of a sidebranching instability when the boundary condition includes anisotropy ...
Sep 1, 2011 ... Description: What amount of extra energy can be generated after subtracting the total energy consumed to produce the biomass energy? ...
Program Plans, Implementation, & Results Energy Management at Federal Facilities Energy Management at DOE Fleet Management Interagency Coordination Interagency Energy...
The in-plane resistivity, in-plane absolute thermopower, and upper critical field measurements are reported for single-crystal samples of YNi{sub 2}B{sub 2}C and LuNi{sub 2}B{sub 2}C superconductors. The in-plane resistivity shows metallic behavior and varies approximately linearly with temperature near room temperature (RT) but shows nearly quadratic behavior in temperature at low temperatures. The YNi{sub 2}B{sub 2}C and LuNi{sub 2}B{sub 2}C single-crystal samples exhibit large transverse magnetoresistance ({approx}6{endash}8{percent} at 45 kOe) in the ab plane. The absolute thermopower S(T) is negative from RT to the superconducting transition temperature T{sub c}. Its magnitude at RT is a few times of the value for a typical good metal. S(T) is approximately linear in temperature between {approx}150 K and RT. Extrapolation to T=0 gives large intercepts (few {mu}V/K) for both samples suggesting the presence of a much larger {open_quotes}knee{close_quotes} than would be expected from ...
Electro Energy, Inc. conducted a research project to develop an energy efficient and environmentally friendly bipolar Ni-MH battery for distributed energy storage applications. Rechargeable batteries with long life and low cost potentially play a significant role by reducing electricity cost and pollution. A rechargeable battery functions as a reservoir for storage for electrical energy, carries energy for portable applications, or can provide peaking energy when a demand for electrical power exceeds primary generating capabilities.
This report presents the full texts of the allocution delivered during the colloquium on the renewable energies and the public policies. It takes stock on the strategical environment and the political will of the renewable energies, the tracks of development in France and the necessity of a law on the renewable energies. (A.L.B.)
Contents: Introduction; Design Criteria for a Green Building; Comparison of Energy Efficiency Measures; Whole House Energy Efficiency; Built Examples of Energy Efficient Houses; and Product Energy of Building Elements.
Since Taiwan lacks sufficient self-produced energy, increasing energy efficiency and energy savings are essential aspects of Taiwan's energy policy. This work summarizes the energy savings implemented by 303 firms in Taiwan's textile industry from the on-line Energy Declaration System in 2008. It was found that the total implemented energy savings amounted to 46,074 ton of oil equivalent (TOE). The energy saving was equivalent to 94,614 MWh of electricity, 23,686 kl of fuel oil and 4887 ton of fuel coal. It represented a potential reduction of 143,669 ton in carbon dioxide emissions, equivalent to the annual carbon dioxide absorption capacity of a 3848 ha plantation forest. This study summarizes energy-saving measures for energy users and identifies the areas for making ...
An ``energy snapshot`` article is included on housing characteristics in 1993 (survey of 7,111 households). The rest of the document is divided into: energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, international energy, and appendices (conversion factors, CO2 emission factors from coal, index, glossary).
This is the June report by the Energy Information Administration. The contents of the report include an energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy. Included are appendices containing thermal conversion factors, metric and other physical conversion factors, and carbon dioxide emission factors for coal.
Denmark has been one of the first countries in the world to commit itself to a sustainable energy development. This has been substantiated by two official action plans from 1990 and 1996 with emphasis on energy efficiency and supply systems based on renewable energy. In year 2005, renewable energy sources are planned to cover 12-14% and in year 2030 about 35% of total Danish energy demand. This paper reviews the experiences with implementation of renewable energy in Denmark with a focus on wind power and biomass.
The Danish Energy Agency has prepared a report on the Danish geothermal resources and their contribution to the national energy potential.Environmental and socio-economic consequences of geothermal power systems implementation are reviewed. Organizational models and financing of geothermal-seismic research are discussed, and the Committee of the Energy Agency for Geothermal Energy recommends financing of a pilot plant as well as a prompt elucidation of concession/licensing problems. (EG).
Energy production during Feb 95 totaled 5.4 quadrillion Btu (Q), 3.1% over Feb 94. Energy consumption totaled 7.4 Q, 0.7% below Feb 94. Net imports of energy totaled 1.3 Q, 5.6% below Feb 94. This publication is divided into energy overview, energy consumption, petroleum, natural gas, oil and gas resource development, coal, electricity, nuclear energy, energy prices, and international energy.
...Climate Change : News Categories : Department of Energy and Climate Change Articles in Smart energy meters Results There are 2 articles listed in Smart energy ... meters DECC lays foundations for smart meters rollout A crucial step in delivering the UK's energy security and low carbon future was taken today ...Nuclear Prices Renewable energy Renewable Heat Incentive Saving energy and CO2 Science Smart energy meters Statistics Statistics and projections Transparency Wave and tidal Wind ...
A new estimator of the local density of dark energy is suggested which comes from the virial theorem for non-relativistic gravitating systems embedded in the uniform dark energy background.
... Geothermal Energy Equipment in Finland on Environmental Expert Find and compare a variety of geothermal energy equipment in finland on the world's largest environmental ...
... Geothermal Energy Equipment in Belgium on Environmental Expert Find and compare a variety of geothermal energy equipment in belgium on the world's largest environmental ...
placed on direct energy conversion. This is an advanced technology which is ..... Of the direct energy conversion methods discussed, the only one which may ...
The purpose of this study was to use high-resolution magnetic resonance (MR) imaging combined with image analysis to investigate the three-dimensional (3D) trabecular structure, anisotropy, and connectivity of human vertebral, femoral, and calcaneal specimens. The goal was to determine whether: (a) MR-derived measures depict known skeletal-site-specific differences in architecture and orientation of trabeculae; (b) 3D architectural parameters combined with bone mineral density (BMD) improve the prediction of the elastic modulus using a fabric tensor formulation; (c) MR-derived 3D architectural parameters combined with BMD improve the prediction of strength using a multiple regression model, and whether these results corresponded to the results obtained using higher resolution depictions of trabecular architecture. A total of 94 specimens (12 x 12 x 12 mm cubes) consisting of trabecular bone only were obtained, of which there were 7 from the calcaneus, 15 from ...
With specific energy of more than 200 Wh/kg, the Electric Fuel zinc-air battery delivers as much as eight times the energy of lead-acid traction battery, more than twice the energy of the nearest advanced-battery competitor, and as much energy as a tank of gasoline. (author)
The discussion of energy usage falls naturally into three parts. The first is a review of what the problem is, the second is a description of steps that can be taken to conserve energy at existing facilities, and the third is a review of the implications of energy consumption on future facilities.
A short survey of the energy situation in Iran is given with the aid of some interesting figures. Following remarks on the national and international energy policy, the developments regarding individual energy sources and electricity production are described.
Keywords: energy, management, conservation, program, fiscal, year, 2005, annual, ...S Environmental Protection Agency Energy Management and Conservation Program ...ENVIRONMENTAL P ROTECTION AGENCY Energy Management and Conservation Program Fiscal Year 2005 Annual Report
The Plan identifies the Army's organization, goals, objectives, and policies with respect to energy. It projects energy consumption and costs to the year 2000 and summarizes the programs required to support the long range goals. A summary of current and needed energy related legislation is included. (Author)
...2010-10-01 false Department of Energy Directives. 970.0470 Section...Acquisition Regulations System DEPARTMENT OF ENERGY AGENCY SUPPLEMENTARY REGULATIONS ...Matters 970.0470 Department of Energy...
...2010-10-01 false Preferences under the Energy Policy Act. 926.7005 Section...Acquisition Regulations System DEPARTMENT OF ENERGY SOCIOECONOMIC PROGRAMS OTHER SOCIOECONOMIC...Implementation of Section 3021 of the Energy Policy Act of 1992 926.7005...
As a result of a lower value of the energy efficiency coefficient (EPC) for houses and the implementation of the Energy Performance Building Directive (EPBD), both in 2006, the interest in applying renewable energy systems is growing. Therefore, this issue is dedicated to renewable energy and related energy systems. [Dutch] Het begrip 'duurzaam' is van toepassing op twee pijlers: een pijler betreft het gebruik van duurzame materialen, de tweede pijler is duurzame energie. Door verlaging van de Energieprestatiecoefficient (EPC) voor woningen per 2006 en de invoering van de Europese richtlijn Energy Performance Building Directive (EPBD) in 2006, krijgt duurzame energie een nieuwe impuls. Reden voor de redactie van ThemaTech om deze aflevering te wijden aan duurzame energie en verwante ...
The National Energy Modeling System (NEMS) developed by the U.S. Department of Energy`sEnergy Information Administration is a well-recognized model that is used to project the potential impact of new electric generation technologies. The NEMS model does not presently have the capability to model energy storage on the national grid. The scope of this study was to assess the feasibility of, and make recommendations for, the modeling of battery energy storage systems in the Electricity Market of the NEMS. Incorporating storage within the NEMS will allow the national benefits of storage technologies to be evaluated.
Integrating phytotechnologies with energy crop production for biofuels, bioenergy, and bioproducts. In: Sixth International Phytotechnologies Conference ; ...
... Areas of Consultation: All Areas About DECC Bioenergy Carbon capture & storage Carbon Reduction Commitment Climate Change Agreements CRC energy efficiency scheme Development, consents and planning reform Electricity Electricity network Emissions Emissions trading Energy markets Energy network Energy security Feed-in Tariffs Fuel poverty Funding and support Gas Governance Green Deal Hydroelectricity International climate change International energy Legislation Low-carbon Microgeneration News Nuclear Oil Renewable energy Saving energy and CO2 Site Wide Footer Smart ...
... energy absorption characteristics of composite sandwich panels, thermoplastic energy-absorbing subfloor structures, and shoulder belt pre- tensioners. ...
The true potential energy curve for the x "1#SIGMA#"+ state of BeO has been calculated using the RKRV method. The dissociation energy of the ground state has been estimated to be 5.15 +- 0.05 eV by the curve-fitting method using the three-parameter potential energy function of Lippincott with an RKRV potential energy curve. (author).
The uncertainties of growth in Croatian future energy, particularly electricity demand, together with growing environmental considerations and protection constraints, are such that Croatia needs to have flexibility to respond by having the option of expanding the nuclear sector. The paper deals with nuclear energy as an option for croatian sustainable economic development. The conclusion is that there is a necessity for extended use of nuclear energy in Croatia because most certainly nuclear energy can provide energy necessary to sustain progress. (author).
The Monthly Energy Review (MER) presents an overview of the Energy Information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. 37 figs., 61 tabs.
This publication presents an overview of the Energy information Administration`s recent monthly energy statistics. The statistics cover the major activities of US production, consumption, trade, stocks, and prices for petroleum, natural gas, coal, electricity, and nuclear energy. Also included are international energy and thermal and metric conversion factors. Two brief ``energy plugs`` (reviews of EIA publications) are included, as well.
Sandia National Laboratories, New Mexico, conducts the Energy Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Utility Technologies. The goal of this program is to assist industry in developing cost-effective energy storage systems as a resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of energy storage systems for stationary applications. This report details the technical achievements realized during fiscal year 1996.
An overall review of status of energy in Lebanon is presented. Energy consumption and demand, in all sectors of economy, including renewable energy sources (biomass, solar energy, kerosene, gas oils...) are described, enhanced by figures and tables. Recommendations of energy development in Lebanon within national economic policy are formulated. 4 tabs.
A combined application of several microtechniques is presented and discussed with the Ti/TiO_2 and Zr/ZrO_2-systems as an example. All measurements were carried out on single grains of technical materials in order to detect and quantify the effect of substrate microstructure on the properties of anodic passive films formed potentiodynamically in 0.5 M H_2SO_4 (dU/dt = 20 mVs"-"1). Anisotropy-micro-ellipsometry (AME) was employed to determine the crystallographic orientation of the substrate grains along with passive film thickness and crystallinity in dependence on the anodization potential. Both the isotropic (amorphous) TiO_2- and the anisotropic (crystalline) ZrO_2-films exhibit a systematic dependence of film thickness on the grain orientation. Local LASER-scanning photocurrent measurements (#lambda#=257 nm) on the same grains likewise show a heterogeneity of the photoelectrochemical reactivity in all cases. This is quantitatively explained by the results from ...
Normal fetal brain maturation can be studied by in vivo magnetic resonance imaging (MRI) from the 18th gestational week (GW) to term, and relies primarily on T2-weighted and diffusion-weighted (DW) sequences. These maturational changes must be interpreted with a knowledge of the histological background and the temporal course of the respective developmental steps. In addition, MR presentation of developing and transient structures must be considered. Signal changes associated with maturational processes can mainly be ascribed to the following changes in tissue composition and organization, which occur at the histological level: (1) a decrease in water content and increasing cell-density can be recognized as a shortening of T1- and T2-relaxation times, leading to increased T1-weighted and decreased T2-weighted intensity, respectively; (2) the arrangement of microanatomical structures to create a symmetrical or asymmetrical environment, leading to structural differences that may be ...
We report on the transport properties of a high mobility two-dimensional hole system (2DHS) confined in GaAs/AlGaAs quantum wells grown by molecular-beam epitaxy on the (100) surface of GaAs. The quantum wells are modulation doped with carbon utilizing a resistive filament source. At T=0.3 K and carrier density p=1x10"1"1 cm"-"2, a mobility of 10"6 cm"2/Vs is achieved. At fixed carrier density p=10"1"1 cm"-"2, the mobility is found to be a nonmonotonic function of the quantum well width. The mobility peaks at 10"6 cm"2/Vs for a 15-nm well and is reduced for both smaller and larger well widths for these (100) samples. The mobility anisotropy is found to be small. Mobility along [011] is approximately 20% higher than along the [011] direction. In addition, the low-temperature carrier density is found to have low sensitivity to light. The hole density increases by only #approx#10% after exposure to red light at T=4.2 K. In structures designed for a lower carrier ...
Substitution of various rare earths R within the class of R2PdSi3 single crystals with hexagonal AlB2-type crystallographic structure reveals the systematic dependence of anisotropic magnetic properties governed by the interplay of crystal-electric field effects and magnetic two-ion interactions. Here we compare the floating zone (FZ) crystal growth with radiation heating of compounds with R = Tb, Tm, Pr, and Gd. The congruent melting behavior enabled moderate growth velocities of 3 to 5 mmh-1. The preferred growth directions are close to the basal plane of the hexagonal unit cell. The composition of the crystals, except of Tb2PdSi3, is slightly Pd-depleted with respect to the nominal composition 16.7 at.% Pd. Thin precipitates of RSi secondary phases were detected in the crystal matrix. Their phase fraction can be diminished by growth from Pd-rich melt compositions and annealing treatments. The compounds exhibit antiferromagnetic order below the N el temperatures TN: 23.6 K ...
Numerical models based on finite-difference or finite-element methods are used by various research groups in studies of radon-222 transport through soil and building materials. Applications range from design of radon remediation systems to more fundamental studies of radon transport. To ascertain that results obtained with these models are of good quality, it is necessary that such models are tested. This document reports on a benchmark test organized by the EU project ERRICCA: European Research into Radon in Construction Concerted Action. The test comprises the following cases: 1) Steady-state diffusive radon profiles in dry and wet soils, 2) steady-state entry of soil gas and radon into a house, 3) time-dependent radon exhalation from a building-material sample. These cases cover features such as: soil heterogeneity, anisotropy, 3D-effects, time dependency, combined advective and diffusive transport of radon, flux calculations, and partitioning of radon between ...
As characterization of artificial cracks formed underground by using the water pressure fracturing method, experiments have been carried out to detect relationship of pressurization and S-wave propagation time with the polarizing direction dependence. Openings are created when pressure in the vicinity of the artificial cracks increases greater than reopening pressure of micro cracks. Elastic wave velocity decreases in this region because of water in the opened micro cracks. Anisotropy is created in the S-wave propagation velocity due to influence from anisotropic reopening region when the artificial cracks are pressurized, and is separated into two components which polarize orthogonally with each other (micro splitting). Field experiments conducted at the Higashi-hachimantai field were analyzed by using wavelet transform. It was possible to detect the S-wave arrival time at high accuracy, and the arrival of an orthogonally polarized wave was observed in 0.03 to ...
This paper describes the results of a French-Lebanese scientific cooperation, between 2001 and 2005, about 'Rational use of energy in the residential buildings in Lebanon and adaptation of an energy certification procedure'. The aim of this project is to promote the energy efficiency in the existing residential buildings in Lebanon, using an energy certification procedure, and to evaluate the energy certification foresight with prospective methods. The paper first describes an energy investigation in Lebanese residential buildings, and the energy certification procedure. It presents the foresight methodology implemented to identify the key variables and the actors. Finally, the paper exposes the morphological method which allows to elaborate three scenarios of energy performance certification. These scenarios are ...
This presentation outlined the energy policy in the United States and its impact on frontier development in Alaska, deepwater offshore fields and in the western oil shale resources. The energy strategy focuses on technologies that increase domestic production from existing resources as well as technologies that create new sources of energy. In addition to emphasizing the cooperation between Canada and the United States in ensuring energy supply security and stability, this paper discussed the importance of overall bilateral trade between the 2 countries. It was noted that Canada is the United State's most secure and reliable energy partner and is the number 1 supplier of imported oil, natural gas, electricity and uranium. The Bush administration's energy policy is based on the mandate to supply stable, reliable, secure, affordable and ...
Security of supply is defined as the availability and reliability of energy supply at acceptable prices. By security of energy supply we mean a globally large supply of reliable, affordable, clean energy. By virtue of its nature security of supply in the energy sector primarily requires making provisions for the future through exploration, innovation, research, diversification and investments in technology. Energy politics takes place in a tension field defined by the goals of economic efficiency, sustainability and security of supply. In the past there have been repeated shifts within this triad of goals. The task for a rational energy policy is to reconciliate these goals in a meaningful way. European energy policy is understood to comprise all sovereign measures taken by the European Union in the energy sector, in ...
Current hydrocarbon-based energy systems, current energy consumption and the push towards the utilization of renewable energy sources, fuelled by global warming and the need to reduce atmospheric pollution are discussed. The consequences of climatic change and the obligation of Annex B countries to reduce their greenhouse gas emissions in terms of the Kyoto Protocols are reviewed. The role that renewable energy sources such as hydrogen, solar and wind energy could play in avoiding the most catastrophic consequences of rapidly growing energy consumption and atmospheric pollution in the face of diminishing conventional fossil fuel resources are examined. The focus is on hydrogen energy as a means of storing and transporting primary energy. Some favorable characteristics of hydrogen is its abundance, the fact that it can be ...
Development of renewable energy systems for remote communities is gaining interest among government, utilities, NGOs and the communities themselves as a means of improving lifestyles of community members and showcasing renewable energy systems. The Huu-ay-aht First Nation, whose traditional territory is located on the west side of Vancouver Island in British Columbia, is a community which has energy related problems and energy related opportunities. The objective of this study is to assess possible energy options for the Huu-ay-aht First Nation traditional territory. Current and future energy services within the territory were used as the starting point for developing energy system options. Extensive consultation with community members was instrumental in clearly defining the objectives of the study and understanding the territory's ...
This paper describes a simulation model for predicting end-use energy consumption in residential sectors of a city or region. In this model, the annual energy consumption of a dwelling is simulated from the occupants' schedule of living activities, weather data and energy efficiencies of appliances and dwellings. By summing up the simulation results for various household categories, total energy consumption for the residential sector in a region can be estimated. In this paper, energy consumption for Osaka City is simulated. The result is compared with statistical data. The effects of energy efficiency standards and urban heat island phenomena are examined. (author)
The section on environmental impacts covers global environmental concerns and air pollution. Energy systems includes the following: alternative fuels; co-generation; fossil fuels; mechanical thermal storage; fission/fusion; thermal management; electric and hybrid vehicles. The section on renewable energy sources includes biomass, hydrogen, and solar. This volume also contains separate sections for stirling cycles, policy issues, and new technologies for energy utilization. Separate abstracts were prepared for 150 papers of this volume.
The paper presents a comprehensive analysis of the energy conservation policy conducted in the Central and Eastern European countries - its development from the start of reforms and up to the present. The problems of rational energy consumption are shown to be closely connected with the concrete conditions of the transition from the economy based on the command principles to the market economy. The author indicates the main areas of application for energy conservation activities. He also describes the models for determination of energy intensity in different branches of energy economy, and organisational structure of the measures to be taken foe energy conservation. (author)
Energy productivity and energy intensity within the industrial sector of the economy are examined. Results suggest that relative prices and other economic factors can explain much of the variation in both energy productivity and energy intensity for manufacturing and mining and for the industrial sector as a whole. Cyclical factors, seasonal factors and trend variables are also useful in explaining variation in these data, both for annual and monthly time series. Of the variables examined, it appears that the relative price of energy is a highly significant factor in accounting for the difference between actual industrial energy intensity and that which might have been expected had pre-1973 trends continued.
The Advanced Power Electronics Interfaces for Distributed Energy Workshop, sponsored by the California Energy Commission Public Interest Energy Research program and organized by the National Renewable Energy Laboratory, was held Aug. 24, 2006, in Sacramento, Calif. The workshop provided a forum for industry stakeholders to share their knowledge and experience about technologies, manufacturing approaches, markets, and issues in power electronics for a range of distributed energy resources. It focused on the development of advanced power electronic interfaces for distributed energy applications and included discussions of modular power electronics, component manufacturing, and power electronic applications.
The Meteorological Service of Canada has made weather datasets available in real-time on the Internet, for use by those with an interest in solar applications. Ensemble weather models can be used to produce medium range forecasts of weather events and to predict the likely available kilowatt-hours (kWhrs) of solar energy. As such, solar sites can maximize their harvest and use of solar energy. This presentation highlighted several different types of renewable energy forecasts obtained from weather models, including forecasts of expected kWhrs from solar panels and wind turbines, daily forecasts of expected solar heated water volumes and forecasts of water collection potential from impending precipitation events. The value of renewable energy forecasts in helping the solar energy sector monitor daily energy loads as well as daily and weekly solar ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. Here we calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favourable for wave amplification from alpha energy. We find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this idea, the use of a lossy boundary to enhance the ...
The interaction between a lower hybrid wave and a fusion alpha particle displaces the alpha particle simultaneously in space and energy. This results in coupled diffusion. Diffusion of alphas down the density gradient could lead to their transferring energy to the wave. This could, in turn, put energy into current drive. An initial analytic study was done by Fisch and Rax. Here the authors calculate numerical solutions for the alpha energy transfer and study a range of conditions that are favorable for wave amplification from alpha energy. They find that it is possible for fusion alpha particles to transfer a large fraction of their energy to the lower hybrid wave. The numerical calculation shows that the net energy transfer is not sensitive to the value of the diffusion coefficient over a wide range of practical values. An extension of this ...
The French agency of environment and energy mastery (Ademe) and Deutsche Energie Agentur (DENA) organised in Berlin on November 22 and 23, 2001, the first seminar and forum of ideas and exchanges on the implementation of energy efficiency and renewable energy policies in France and in Germany. On this occasion, Ademe asked Energie-Cites - an association of European cities with a long practical experience in 'good practice' exchanges - to prepare a publication describing the experience of about ten French cities or local energy agencies in energy management issues. The case studies presented in this document concern the following cities: Besancon, Dole, Dunkerque, Lille, Montpellier, and the local energy agencies of Clermont-Ferrand (Aduhme), Grenoble, Montreuil-Vincennes, Mulhouse and Rennes. (J.S.)
Primary energy consumption per unit of gross domestic product (GDP) indicates the importance of energy as an input to an economy. The most important determinant of energy consumption per GDP unit is economic structure, although the efficiency with which energy is used and the availability of non-commercial energy sources are also significant. Energy consumption intensities among the industrial nations reflect, in part, the vigor with which energy conservation and substitution policies have been pursued in the past decade. Energy production intensities indicate resource endowment, and may vary from zero to close to 100% of GDP. Comparisons of the seven world regions note that the centrally planned economies distort the figures because of their method of measuring economic output. 1 table.
The IEA has identified energy efficiency as essential to achieving a sustainable energy future. In order to improve energy efficiency in industry one of the priority areas for further action is the promotion of more and higher quality energy management (EM) activity. However, there are significant gaps in the current implementation of EM. One method of bridging these gaps would be the creation of an EM Action NetworK (EMAK) to bring practical support to energy managers, connect energy managers to energy policy makers, and interconnect these networks globally. The paper describes possible aims, activities, scope, structure, timelines and approaches related to EMAK and looks at specific tasks that would be important in the set-up and implementation.
may be possible to meet those loads with renewable energy systems &mdashachieving zero-net- energy performance.Solar-thermal heating systems, ...p/p Spencer and others argue that renewable energy systems should be considered only after the building envelope ...energy loads are brought low enough, however, a renewable energy system may make sense financially. p
...Simplification of the scheme - Department of Energy and Climate Change simplification, crc energy efficiency scheme Simplification of the scheme Simplification of the CRC Energy ...Efficiency Scheme The Government is considering the simplification of the CRC in the light of experience since the scheme began in April 2010. ...will take into account feedback from stakeholders including: the effectiveness of the CRC framework for driving energy efficiency in large private and public sector ... The perceived complexity of the CRC scheme and hence the administrative burden on: - those organisations that are subject to ...
The article explains the method of selecting the optimum energy for correcting the energy selectivity of tomographic projection and the optimum length of the crystals corresponding to it when the dual energy method in computerized tomography is used. Results of numerical calculations for actual materials and count results are presented.
This short article describes the strategies taken into consideration by the Swiss Federal Office of Energy for the promotion of renewable forms of energy in Switzerland. Two basic models are considered and the parts to be played by the Swiss Confederation, the Swiss Cantons, Energy Agencies and professional organisations are discussed. The importance of the activities of partner organisations and actor-networks in various areas such as solar, small hydro, geothermal and wind energy are discussed, as are models for financing the necessary promotion and marketing efforts
This 2001 status on the use of renewable energies in France makes a synthesis of the electric and heat productions of renewable origin. It lists the primary or secondary productions of renewable energies, and details the uses corresponding to each renewable energy production source and their respective satisfaction of consumer's needs (residential, industry and agriculture sectors). A detail statistical status for 1999, 2000 and 2001 is presented in tables. (J.S.)
DescriptionFossil fuels have a detrimental effect on the environment. They lead to the increase in atmospheric carbon dioxide which has been documented over the last 150 years. In contrast, some sources of renewable energy are near carbon neutral. Renewable energy produced from biomass constitutes such a type of energy and so has many potential advantages. The Energy White Paper (DTI et al., 2003) identifies bioenergy as an important means of meeting the Government's energy and environment objectives, in [continued...
Clear effects of the Act on Power Generation from Renewable Energy Sources (EEWaermeG) on the market cannot be recognized both for the depth geothermal energy and ground source geothermal energy. Due to the concrete design of the law a position that is inferior to others is attained in relation to some other renewable energy sources.
Contains Executive Summary and Chapters on: Energy and the Internet; Internet Developments; Search Guide; Oil and Gas Industry; Electricity and Utilities; Nuclear Energy; Coal Industry; Alternative Energy; Government and Supranational Agencies; Research Institutions and Universities; Energy Statistics; Commodity Pricing and financial Markets; Company Information; Country Information; Associations; Engineering; Environment; Patents, Trademarks and Standards; News; Industry Events; Miscellaneous. (Author)
The purpose of this analysis is to develop a systematic program of projects that will result in energy consumption reductions in compliance with the stated goals of the Army Facilities Energy Plan for the Stratford Army Engine Plant in Stratford, Connecticut. Reduced energy consumption is a stated goal for the Army Facility Energy Plan.
A series of speeches is presented which cover political aspects of ocean energy, legislation, the status of the DOE Ocean Energy Program, the Maritime Administration OTEC Support Program. Six workshop reports are given covering ocean energy technology and systems concepts, power systems concepts, environmental developments, energy transfer and utilization, construction and test capabilities, and industry development. (LEW)
This quarterly newsletter provides timely news and information about the plans and progress of the Energy Development in Island Nations U.S. Virgin Islands pilot project, including significant events and milestones, work undertaken by each of the five working groups, and EDIN-sponsored renewable energy and energy efficiency projects.
The US Department of Energy, Office of Technical and Financial Assistance (OTFA) promotes the application of renewable energy and energy efficiency technologies and practices by working cooperatively with state and local governments and private and nonprofit organizations, providing technical and financial assistance and serving as network for sharing information. This report is an overview of some of the programs designed to aid in solving our national energy problems.
The inevitability of sustainable economic development and its linkage to a gradual shift to renewable energy sources, especially solar energy, was discussed. Means to measure sustainability of technology were described, and policy instruments (essentially research, development and demonstration, and punitive taxes on conventional energy carriers) to accelerate the shift to renewable energy sources were outlined.
Mitsubishi Research Institute has analyzed the energy demand of a typical Japanese city, Yokohama, as well as the distribution of fossil-energy flow, and the final consumption by sectors. It has evaluated the effectiveness of various energy conservation measures, (e.g., cogeneration, electric cars, insulation,...) in countering the global warming trend. This study defines a viable methodology which may be utilized, in the future, in examining the effectiveness of environmental policies. (TEC). 1 tab., 4 figs.
As the 20th century draws to a close, both individual countries and the world community face challenging problems related to the supply and use energy. These include local and regional environmental impacts, the prospect of global climate and sea level change associated with the greenhouse effect, and threats to international relations in connection with oil supply or nuclear proliferation. For developing countries, the financial cost of providing energy to provide basic needs and fuel economic development pose an additional burden. To assess the magnitude of future problems and the potential effectiveness of response strategies, it is important to understand how and why energy use has changed in the post and where it is heading. This requires study of the activities for which energy is used, and of how people and technology interact to provide the energy services that are desired. ...
As the 20th century draws to a close, both individual countries and the world community face challenging problems related to the supply and use energy. These include local and regional environmental impacts, the prospect of global climate and sea level change associated with the greenhouse effect, and threats to international relations in connection with oil supply or nuclear proliferation. For developing countries, the financial cost of providing energy to provide basic needs and fuel economic development pose an additional burden. To assess the magnitude of future problems and the potential effectiveness of response strategies, it is important to understand how and why energy use has changed in the post and where it is heading. This requires study of the activities for which energy is used, and of how people and technology interact to provide the energy services that are desired. ...
Environmental Protection Agency Energy Management and Conservation Program ...Environmental Protection Agency Office of Administration and Resources Management 1200 Pennsylvania Avenue, NW (3101A) ...MANAGEMENT AND ADMINISTRATION 7 Energy Management Infrastructure 7 Senior Agency Official and Energy Team 7
This fact sheet highlights how renewable energy and energy efficiency technologies can and are being used to reduce air emissions and meet environmental goals, showcasing case studies and technology-specific topics.
By placing a discharge or 'dump' tube across an exploding bridgewire load, it is possible to by-pass the electrical energy and terminate the explosion of the wire. The dump tube is triggered by a signal derived from the energy removed from the storage cap...
The melting unit, consisting of a water-cooled cupola furnace, afterburner, heat exchanger, air preheater, consumes most of the supplied energy in the rockwool process. The report maps the energy flows and defines factors of merit according to thermodynam...
In the case of total skin electron therapy without the beam guide, the electron beam is scattered just outside the gantry exit, dose uniformity in the field is broken, and dose is spread outside the light field. The aims of this study were to measure the mean energy of the off-axis incident electron beam without the beam guide and to establish a reference for the clinical situation. For the measurement, a 4 MeV electron beam was selected among several energies from the linear accelerator. A scintillating fiber beam energy monitor measured the mean energy of the incident electron beam. This energy monitor is a small, light-weight piece of equipment composed of a wedge absorber, scintillation fiber, and photodiode. We found the relationship between electron energy and the indicated value of the energy monitor by means of the estimation of ...
The high-energy reaction cross sections of Li and Be isotopes are calculated using a simplified Glauber model and densities constrained by the empirical binding energies. We find excellent agreement with experiment, reproducing the large increase for the most neutron-rich nuclei.
Title: FY 2004 Energy Management and Conservation Program Annual Report ...Energy Management and Conservation Program ...Environmental Protection Agency Office of Administration and Resources Management 1200 Pennsylvania Avenue, NW (3101A)
The following manual chapters are outlined and described: overview, boilers, juice evaporators, feed mills, refrigeration, additional energy savings potentials, emerging technologies, optimization of integrated plant energy systems, and economics. (MHR)
;Contents: Energy Use; Building Fabric Performance; Ventilation and Infiltration; Passive Solar Design; Heating Systems and Controls; Hot and Cold Water Provision; and Lighting and Electrical Appliances.
Contents: Energy Use; Building Fabric Performance; Ventilation and Infiltration; Passive Solar Design; Heating Systems and Controls; Hot and Cold Water Provision; and Lighting and Electrical Appliances.
This paper deals with electron flux densities and electron energy flux densities in positive column discharges. Recent kinetic calculations by Uhrlandt and Winkler have revealed the interesting physical phenomenon of radially inward directed energy flux densities in positive column plasmas. We have used a self-consistent positive column model, based on an accurate and highly detailed Monte Carlo code, to study this effect in more depth. The results of this study show a rather complex physical picture of electron particle and energy flux densities. Electrons with low energies usually exhibit radially outward directed particle and energy flux densities. At energies above the threshold for electronic excitation particle and energy flux densities are usually inward directed. Only close to the wall, at total energies above ...
The energy-momentum tensor of a massless spinor field is constructed and studied based on the previously proposed interpretation of quantum effects of such a field in the anisotropic metric of Bianchi type IX. The characteristic properties of the energy-momentum tensor in the mixed universe model are discussed.
The report deals with the energy consumption of traffic and its emissions of hazardous substances into the air, and stresses the advantages of the electric car with respect to energy consumption and noise generation. 5 figs., 3 refs.
Energy study was conducted in an organic fertilizer production plant in Nigeria, to determine the energy consumption patterns and the associated costs for the production of both powdered and pelletised fertilizer. Analysis was conducted for a daily production of 9000 kg of the finished products. Eight and nine defined unit operations were required for production of powder and pellets, respectively. The electrical and manual energy required for the production of powder were 94.5 and 5.6% of the total energy, respectively, with corresponding 93.9 and 5.1% for the production of pellets. The respective average energy intensities were estimated as 0.28 and 0.35 MJ/kg for powder and pellets. The most energy intensive operation was identified as the pulverizing unit with energy intensity of 0.09 MJ/kg, accounting for respective proportions of 33.4 ...
This volume is a summary of the results of the final report of the Energy Engineering Analysis Program (EEAP) Study of 30 selected dining facilities at Fort Campbell, Kentucky.
The problems of introducing renewable energy systems into communities having meagre resources are analysed. Topics covered include financial and economic barriers, subsidies and bank policy. It is concluded that without satisfactory financing mechanisms, renewable energies are unlikely to be widespread in the developing world. (UK)
The objective of this project is to reduce energy consumption in 203 buildings by providing a new EMCS (Energy Monitoring Control System) to control and monitor systems.
... Question Chronic fatigue: Can natural remedies boost my energy? Are there any natural remedies that reduce chronic ... AN01764 ">Chronic fatigue: Can natural remedies boost my energy? Guidelines for sites linking to MayoClinic.com ...
A new energy concept known as centrifugal potential energy was discussed. This new energy concept is capable of increasing the pressure, temperature and enthalpy of a fluid, without having to apply work or heat transfer to the fluid. It occurs through a change in the centrifugal potential energy of the flowing fluid in a rotating frame of reference or a centrifugal force field, where work is performed internally by the centrifugal weight of the fluid. This energy concept has resulted in new energy equations, such as the Rotational Frame Bernoulli's Equation for liquids and the Rotational Frame Steady-Flow Energy Equation for gases. Applications of these equations have been incorporated into the design of centrifugal field pumps and compressors. Rather than compressing a fluid with a physical load transfer, these devices can compress ...
Computer assisted energy-spectral analyses were obtained on EEG recordings of unilateral non-dominant hemisphere ECT-induced seizures using the different pre-ECT anesthetic agents methohexital (Brevital), Innovar, and ketamine (Ketalar). The previously postulated predominance of electrical energy over the stimulated (right) hemisphere early in ECT-induced seizures is confirmed. There appears to be marked reduction in total seizure energy with methohexital anesthesia, whereas ketamine anesthesia appears to be associated with increased overall seizure energy. The greatest right to left energy transfer during the seizure occurred with Innovar anesthesia. PMID:7172456
This is the first report about a relevant and compiled information on the Mexican Energy Sector. It was realized in one volume by the University Energy Program of the National Autonomous University of Mexico and it comprises information for the period 1996-1997. In the chapter 1 there are presented the numbers of hydrocarbon reserves. Chapter 2 treats about production, events and its results. Likewise chapter 3 shows information about the typical Installations for petroleum, gas and electricity including through of the nuclear energy. In the chapter 4, named Energy Consumption, is presented a National energy balance for 1996 and, finally there are a sections about the prices, the rates and a glossary to facilitate its understanding. (Author)
This report issued by the Energy Economics Group and the Laboratory for Energy Systems Analysis at the Paul Scherrer Institute (PSI) analyses current and future trends in the area of energy and mobility on a global, European level as well as with respect to the German-speaking countries Austria, Germany and Switzerland. In a first step, developments with regard to how mobility is achieved and the energy consumption involved are examined and the impact of business-as-usual trends on global carbon dioxide (CO2) emissions and future fuel consumption is discussed. In a second step, the paper outlines potential alternative futures in terms of energy and mobility. Finally, the paper derives and presents recommendations for policy-makers.
This report issued by the Energy Economics Group and the Laboratory for Energy Systems Analysis at the Paul Scherrer Institute (PSI) analyses current and future trends in the area of energy and mobility on a global, European level as well as with respect to the German-speaking countries Austria, Germany and Switzerland. In a first step, developments with regard to how mobility is achieved and the energy consumption involved are examined and the impact of business-as-usual trends on global carbon dioxide (CO2) emissions and future fuel consumption is discussed. In a second step, the paper outlines potential alternative futures in terms of energy and mobility. Finally, the paper derives and presents recommendations for policy-makers.
The feasibility of a high-energy electron cooling device has been studied through tests on a prototype of the electron device. The apparatus consists of a pulsed ((20-60) keV, 2#mu#s) electron gun, a drift region 1 m long and of a depressed collector for recovering the electron energy. Tests on beam optics and energy recovery have been performed, a high-energy recovery efficiency has been attained. Experimental results are discussed in this paper.
The purpose of this paper is to inform commercial building designers about an energy analysis tool which can aid them in making appropriate decisions about daylighting. The energy nomographs are an energy design tool which calculate the annual energy consumption of commercial buildings, including lighting, heating, cooling, domestic hot water, fans, pumps, and miscellaneous items. This paper specifically discusses the daylighting aspects of the tool. The calculation procedure is presented with an example to explain how this design tool can be used to make good energy decisions early in the design process.
A complete guide to 7000 key decision makers and 2800 organizations actively involved in energy today, the 1983 Directory updates the changes in state and Congressional energy offices that resulted from the 1982 elections, the reshuffling at DOE, the shifts of jurisdiction at the Department of the Interior, and the increasing role of the private sector in funding energy research and development. New features include the addition of nearly 100 major venture-capital firms and key public-affairs contacts. The Directory also features an Annual Energy Review highlighting development that will have international effects in the coming year.
In this short communication, we discuss the energy consumption trends in the Malaysian road transport sector, with a special emphasis on the energy losses due to vehicle aerodynamic drag on highways. The recent trends of energy consumption in the Malaysian road transport sector are reviewed. It is evidently shown that the aerodynamic losses represented exceed 1.2MTOE annually since 2002. A novel concept of vertical-axis wind turbine (VAWT) farms for harvesting aerodynamic energy losses on Malaysian highways is preliminarily proposed. The novel concept aims at providing a sustainable and green energy source for the lighting of the highway network in the country.
Subcommittee of the Joint Committee on Atomic Energy of the United States, Outer Space Propulsion by Nuclear Energy, hearings, 85th Cong., 2d sess., 22, ...
Sep 1, 2011 ... Recent wildfires in interior Alaska have left substantial volumes of burned timber, potentially usable for biomass energy. Motivated,in part, by ...
Mitochondria are the major sites where energy is produced in the cell. Functions of organs such as the heart which has high energy demand are seriously affected by dysfunction of mitochondria....Full Text Available
In the framework of the renewable energies development policy and the energy mastership wanted by the Government, a document has been asked by the Prime Minister. It evaluates the development prospects at long and medium dated, of the main chains of renewable energies production taking into account the national developable deposits size, the technologies assessment, the environmental impacts and the competition facing the traditional energies. It evaluates the measures leading to an increasing efficiency. Measures concerning the regulations, the budget, and the fiscality are also discussed. From these analysis, a national strategy for actions in favor the renewable energies, are proposed. (A.L.B.)
The assets that Citizen Potawatomi Nation holds were evaluated to help define the strengths and weaknesses to be used in pursuing economic prosperity. With this baseline assessment, a Planning Team will create a vision for the tribe to integrate into long-term energy and business strategies. Identification of energy efficiency devices, systems and technologies was made, and an estimation of cost benefits of the more promising ideas is submitted for possible inclusion into the final energy plan. Multiple energy resources and sources were identified and their attributes were assessed to determine the appropriateness of each. Methods of saving energy were evaluated and reported on and potential revenue-generating sources that specifically fit the tribe were identified and reported. A primary goal is to create long-term energy strategies to explore development of ...
Within the framework of a modified Balitsky-Kovchegov equation, we calculated and provide estimates of non-linear saturation effects expected in the LHC range of energies.
Energy saving technologies in the railway vehicle traction field can be mainly categorized into two domains: reducing loss and increasing the regenerative energy. Energy saving technologies for the traction equipment by the use of power converters with less loss and high-efficiency permanent magnet synchronous motors are introduced. The regenerative brake related technologies are also presented as another measure to save the energy, including the improvement of the regenerative brake control and application of energy storage devices. It is concluded that the benefit of the energy saving technology is not only the energy saving itself but also downsizing traction equipments and reducing the maintenance work in the electrical railway system. Copyright Copyright 2010 Institute of Electrical E...
Energy consumption of black coal mines in Poland and methods for energy conservation are evaluated. Organizational models of energy management in underground coal mining are discussed. Tasks for dispatcher service for energy consumption control in a coal mine are analyzed: control of energy supplies, control of energy consumption, evaluation of electrical failures and reliability of protection systems, recording accidents and analyzing their causes, optimization of power systems in underground mines. Problems associated with control of energy consumption in a coal mine with mechanized systems for coal mining and use of computerized control systems are discussed. Recommendations for reucing energy consumption in underground coal mining are made. 4 references.
The kinetic energy transferred to some elements by an electron of kinetic energy 100 to 400 kV is discussed. The displacement rates are compared to the signal generation. (DCL)
This bibliography contains 3920 references including abstracts, to information on the technology of flue gas desulfurization and denitrification. These references and others are included in the Department of Energy's Energy Data Base (EDB) through Decembe...
Of the many energy-conservation options available to the design engineer, a system-management approach is recommended as one that will effect maximum benefits to the owner. Systems management includes energy-conscious consideration of design criteria, design details, installation, testing and balancing, and operation. It requires the informed participation of the design engineer, contractor, testing and balancing (TAB) engineer, and owner/operator. Within limits, almost every component of HVAC systems offers an opportunity to conserve energy. Many of these impact energy determinants such as system static pressure, system total air flow, or the quantity of outside air. A few design considerations for energy conservation in a simple system and the impact that the TAB work has on these are illustrated. Particular attention is devoted to the energy impact of systems ...
This study on the role of energy in the development of rural areas was originally conducted in the spring and summer of 1985. It was intended to serve as a background paper for the preparation of a program plan for the Office of Energy of the United States Agency for International Development. As such it begins with a brief overview of how rural development fits into national development, then offers a comprehensive framework for thinking about rural development in particular and the energy implications of the various components of rural development. Agriculture naturally comes to mind when rural areas are mentioned, but industry is an important component of rural activity as well. Consequently, both agricultural and nonagricultural energy use is discussed. Modernization of rural areas will change household, as well as production, energy use. However, household ...
2011 Department of Energy Investments in Carbon Capture Technologies 2010 Smart Meter Installations DOE Recovery Field Projects and State Memos Advanced Vehicle...
In this paper, we consider the development of demand-side research, from an early interest in conservation behavior to a later focus on physical, economic, psychological and social models of energy consumption. Unfortunately, none of these models account satisfactorily for measured energy consumption in the residential sector. Growing interest in the end-uses of energy (e.g. in support of load forecasting, demand-side management and least-cost utility planning), increasing international studies of energy use, and continuing work in the energy and lifestyles research tradition now support an emerging cultural perspective on household energy use. The ecological foundations of the cultural model and its applications in energy research are discussed, along with some of the analytic consequences of this approach. (author).
The study of the intrinsic behavior of high transition temperature copper-oxide superconductors (HTSC) has proven to be challenging because of the extreme sensitivity of their transport properties on material quality. These compounds are characterized by a high degree of structural and electrical anisotropy, and a very short superconductive coherence length of the same order as the size of the crystalline unit cell (~5-30 A). As a result, microscopic defects such as oxygen vacancies, cationic disorder, and the presence of minute impurities have a significant effect on electrical transport in these materials. Therefore, much effort has been expended in synthesizing sizable samples that are homogeneous, well characterized, and emenable to the study of the anisotropic properties of the HTSC. We have demonstrated that thin films of HTSC compounds such as rm YBa_2Cu_3O_{7 -delta}, which is a 92 K superconductor, can be synthesized easily by a technique known as pulsed ...
The aims of this study are determining the energy use, qualitative analyzing of energy flow and also investigating energy efficiency by Data Envelopment Analysis (DEA) in corn production of Iran during a seven years period. Results indicated that the average of total energy input increased from 40.98 GJ ha-1 in 2001 to 63.64 GJ ha-1 in the year of 2007. Similarly, the average of total output energy rose from 89.03 to 107.54 GJ ha-1 in the same years, respectively. Also the results showed that average energy use efficiency, energy productivity, specific energy and net energy gain in the studied period was 2.59, 0.17 kg MJ-1, 7.24 MJ kg-1 and 51.34 GJ ha-1, respectively. DEA considered the yield (kg ha-1) as output and three major energy inputs; fertilizers, diesel fuel and ...
Interest in renewable energy systems that employ regenerative components to enable intermittent energy sources to service time varying loads is growing. The overall performance of these systems is intimately linked to the choice of the energy storage media and the efficiency of the energy conversion devices. Recent advances in electrolyser and fuel cell technologies may make small-scale hydrogen buffered renewable energy systems a practical reality in the near term. A research team at the University of Victoria - Institute for Integrated Energy Systems (IESVic) is developing a flexible distributed, laboratory-scale energy system called IRENE (Integrated Renewable Energy Experiment). The initial goal of this research is to explore the potential for constructing a regenerative energy system using early ...
Johnson & Johnson has had a formal energy program since the early 1970`s. A corporate energy department was formed as a result of the disruption of energy supplies and rising energy costs. Johnson & Johnson is a decentralized company with many independent operating companies throughout the world. The corporate energy department cuts across the different levels of management to delivery energy related information to the actual implementers at all of our locations worldwide. Like many other energy programs, Johnson & Johnson`s program had highs and lows depending on worldwide energy activities. Unlike many other corporate programs that were disbanded in the late 1980`s, our program remained in place, although there was not a high level of interest or attention. In the early 1990`s, the link was made between ...
This work deals with a study on estimation of energy consumption in eight readily defined unit operations of cashew nut processing. Data for analysis were collected from nine cashew nut mills stratified into small, medium and large categories to represent different mechanization levels. Series of equations were developed to easily compute requirements of electricity, fuel and labour for each of the unit operations. The computation of energy use was done using spreadsheet program on Microsoft Excel. The results of application test of the equations show that the total energy intensity in the cashew nut mills varied between 0.21 and 1.161MJ/kg. Electrical energy intensity varied between 0.0052 and 0.029MJ/kg, while thermal energy intensity varied from 0.085 to 1.064MJ/kg. The two identified energy intensive operations in cashew nut processing are cashew nut drying ...
Energy and exergy studies were conducted in an orange juice manufacturing industry in Nigeria to determine the energy consumption pattern and methods of energy optimization in the company. An adaptation of the process analysis method of energy accounting was used to evaluate the energy requirement for each of the eight defined unit operations. The types of energy used in the manufacturing of orange juice were electrical, steam and manual with the respective proportions of 18.51%, 80.91% and 0.58% of the total energy. It was estimated that an average energy intensity of 1.12 MJ/kg was required for the manufacturing of orange juice. The most energy intensive operation was identified as the pasteurizer followed by packaging unit with energy intensities of 0.932 and 0.119 MJ/kg, ...
In earliest works devoted to proton computed tomography it was shown that the advantage of pCT image reconstruction appears when the energy is close to the Bragg peak region, since the proton passes the object. This effect provided by the Bragg peak makes the computerized tomography with protons possible. However, when decreasing the initial proton energy, with the increase of the irradiation dose, there are two effects that work simultaneously in opposite ways. First, the energy loss of a proton in an object becomes bigger at small initial energy. At the same time decreasing of the proton energy results in the increase of the energy straggling, requiring a larger number of protons. In this work the radiation dose dependence on the proton initial energy was studied using analytical formulas and computer simulations. The investigation ...
This document gathers the available presentations (articles and transparencies) given at this annual meeting, the 2007 topic of which was the technological, geopolitical, economical, environmental, societal and development stakes of energy. 1 - technological stakes - which energies for the future: new energies, illusion or solution of the future; the Lorraine region, an energy land: strategies and stakes for a sustainable development; from China to Brazil: understanding the nuclear energy revival; hydroelectric power: renewable and sustainable energy; renewable energies and environment protection: the contribution of biofuels; wind power in Germany between success and contestation; 2 - geopolitical stakes - energy levier of power: the Gulf of Guinea hydrocarbons: between development and geopolitics; the complex ...
Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. The goal of this program is to assist industry in developing cost-effective battery systems as a utility resource option by 2000. Sandia is responsible for the engineering analyses, contracted development, and testing of rechargeable batteries and systems for utility energy storage applications. This report details the technical achievements realized during fiscal year 1994.
Sandia National Laboratories, New Mexico, conducts the Utility Battery Storage Systems Program, which is sponsored by the US Department of Energy`s Office of Energy Management. In this capacity, Sandia is responsible for the engineering analyses, contract development, and testing of rechargeable batteries and systems for utility-energy-storage applications. This report details the technical achievements realized during fiscal year 1993.
To foster rural economic development and growth, Congress passed the Renewable Energy Systems and Energy Efficiency Improvements Program as Section 9006 of the 2002 Farm Bill. This program provides financial assistance to farmers, ranchers, and rural small businesses to purchase renewable energy systems or make energy efficiency improvements. The Rural Business and Cooperative Services of the United States Department of Agriculture (USDA) administers this program. This conference poster provides an overview of Section 9006.
Energy sector is relatively easy to evaluate economically. There have existed reliable statistics on energy systems and consumption and the planning has been based on them. However the environmental factors have been integrated into the Danish energy policy first in the nineties, and the new socio-economic evaluations have to take the pollution abatement measures into account. (EG)
Smart electricity and gas supply grids are a prerequiste for full-scale utilization of the potential of modern energy-saving appliances and equipment. Direct exchange of information between the supplier and the consumer is indispensable for reducing costly and energy-intensive peak loads. (orig.)
The report is an overview on the production of the nuclear energy all over the world. The amount of production at present and in future, availability of the nuclear fuel, development of nuclear technology, environmental and safety issues, radioactive waste management and commissioning of the plants and also the competitivity of nuclear energy compared with other energy forms are considered. (91 refs.).
Several of the issues of the workshop are addressed from the perspective of a potential Space Station developer and energy wheel user. Systems considerations are emphasized rather than component technology. The potential of energy storage wheel (ESW) concept is discussed. The current status of the technology base is described. Justification for advanced technology development is also discussed. The study concludes that energy storage in wheels is an attractive concept for immediate technology development and future Space Station application.
The aim of this paper is to provide a general view of wave energy resource assessment. First, a review of the origin of waves and the transformation they undergo as they propagate towards the coast through waters of decreasing depth is presented. Following this, the wave and wave-energy parameters and the statistics required for resource characterization are described. The various types of wave data and their usefulness for the present purposes are summarised. A common methodology for assessment of the wave energy resource is developed. Finally, a general description of the global open ocean resource is presented.
Science and technology are at the heart of everything we do at the National Renewable Energy Laboratory, as we pursue innovative, robust, and sustainable ways to produce energy--and as we seek to understand and illuminate the physics, chemistry, biology, and engineering behind alternative energy technologies. This year's Research Review highlights the Lab's work in the areas of alternatives fuels and vehicles, high-performing commercial buildings, and high-efficiency inverted, semi-mismatched solar cells.
Institutional issues play a critical, but often overlooked, role in the implementation of renewable energy systems. This paper briefly reviews the institutional arrangements involved in deploying renewable energy from both the sender and receiver perspectives, giving the institutional basis principal characteristics, and pros and cons of each institution. It then offers several perspectives on the critical issues facing the deployment of renewable energy systems before offering a number of potential institutional based solutions. (author)
In this work, energy-based features for gear fault diagnosis and prediction are proposed. The instantaneous energy density is shown to obtain high values when defected teeth are engaged. Three methods are compared in terms of sensitivity, reliability and computation effectiveness. The Wigner Ville distribution is contrasted to the wavelet transform and the newly proposed empirical mode decomposition scheme. It is shown that all three methods are capable of a reliable prediction. An empirical law, which relates the energy content to the crack magnitude is established.
Power generated by manufacturers and third-party suppliers in venture capital projects is available to military and other government users at a cost 10 to 20% lower. Tax benefits and other financial incentives keep suppliers' costs low. Users are required to contract for a minimum amount of energy over a 20- to 30-year period. Military use of these energy projects includes sources based on solar energy, cogeneration, geothermal heat, and refuse-derived fuel. (DCK)
This document deals with energy management in buildings. It presents the conditions for a good implementation of energy management. These conditions include the total involvement of the management and the training of the staff. The structure of this implementation is presented together with the tools for an efficient energy management. Eventually, information on air quality and comfort in buildings is provided, as well as the management of complaints linked to them. (TEC). 1 tab.
An overview of the present status of energy sector in Lebanon and requirements of its future development is presented. The study is based on an economic analysis of needs and energy consumption among the population and on a comparison with other developing countries. Tables and graphs on energy distribution, needs and demands per habitant and national income are included. 3 figs. 3 tabs.
This paper shows the characteristics of the fertilizer production park of the State of Minas Gerais, Brazil, mainly in the aspects of energy consumption and energy sources used in the production process of the various kinds of fertilizers and by-products. A scenario including the fertilizer production evolution was made, relating this future production with the future energy consumption of this sector. 7 figs., 2 tabs.
The RKR potential energy curves are constructed for the ground states of diatomic hafnium oxide and thorium oxide. Using Lippincott and Hulburt-Hirschfelder potential function the dissociation energies are estimated by curve fitting method. The H-H potential function was found to give a better fit in both cases. The dissociation energies of hafnium oxide and thorium oxide are estimated as 9.04 #+-# 0.02 eV and 10.34 #+-# 0.01 eV respectively. (author).
CEA is a public body devoted to technological research with 9 research centers throughout France. The activities of its 16,000 scientists, engineers, and technicians deal with new technologies for nuclear energy and alternative energies (fuel batteries, solar energy, energy storage) as well as technologies related to the new economy, in particular in the fields of microelectronics, bio-technologies, and materials. (author)
Pollutant emissions due to fossil fuel and biomass energy utilization in Turkey have been estimated. Standard emission factors were used for estimating the levels of particulate matter, sulfur oxides, nitrogen oxides, carbon monoxide, volatile organic compounds, and aldehydes. The results are presented for different fuels and energy-consuming sectors for the reference year 1987. Total Turkish emissions vs energy consumption are presented for every fifth year since. 1960. (author).
The Lawrence Livermore National Laboratory (LLNL) is establishing a local chapter of the University of California Energy Institute (UCEI). In order to most effectively contribute to the Institute, LLNL sponsored a workshop on energy and environmental issues in transportation. This workshop took place in Livermore on August 10 and brought together researchers from throughout the UC systems in order to establish a joint LLNL-UC research program in transportation, with a focus on energy and environmental impacts.
...2010-10-01 2010-10-01 false Energy Policy Act target group certification...Acquisition Regulations System DEPARTMENT OF ENERGY CLAUSES AND FORMS SOLICITATION...Provisions and Clauses 952.226-73 Energy Policy Act target group...
...2010-10-01 false Low-income home energy assistance. 96.48 Section 96...Organizations § 96.48 Low-income home energy assistance. (a) This section applies...Indian tribes under the low-income home energy assistance program. (b) The...
Renewable energy systems, such as photovoltaic and wind-turbine energy systems, are considered to be environmentally sound from the viewpoint of carbon-dioxide emissions and resource depletion. The cost of energy supplied from renewable energy systems is higher than that of conventional fossil-fuel systems, and this hinders the wider spread of renewable energy systems. Global environmental problems, however, are becoming more obvious. There is a movement to defray the additional cost of electricity generated in environmentally-sound processes. In this paper, we report the results of a survey using the contingent valuation method (CVM) of the willingness of Japanese households to pay more, in the form of a flat monthly surcharge, for renewable energy. The median value of willingness to pay for renewable energy by Japanese households is ...
We develop the formalism of a unified semi-microscopic description of low-energy proton and {alpha}-particle interaction with nuclei. We analyze elastic and inelastic proton scattering at the energy 25.05 MeV and {alpha}-particle scattering at the energy 104 MeV by the {sup 90}Zr nucleus. Information is obtained on differences in the deformation of the proton and neutron distributions. We study the energy dependence of the semi-microscopic {alpha}-particle potential including the energy dependence of the potential geometry.'' We analyze the change in angular distributions of elastically scattered {alpha} particles with increase of energy and the contribution to the scattering cross section from nucleon-nucleon correlations.
A module is described with a receiver having a solar energy acceptance opening and supported by a mounting ring along the optic axis of a parabolic mirror in coaxial alignment for receiving solar energy from the mirror, and a solar flux modulator plate for varying the quantity of solar energy flux received by the acceptance opening of the module. The modulator plate is characterized by an annular, plate-like body, the internal diameter of which is equal to or slightly greater than the diameter of the solar energy acceptance opening of the receiver. Slave cylinders are connected to the modulator plate for supporting the plate for axial displacement along the axis of the mirror thereby shading the opening with respect to solar energy flux reflected from the surface of the mirror to the solar energy acceptance opening.
The Seismic Proving Test of Heavy Component with Energy Absorbing Supports has been conducted to prove the reliability of advanced seismic technology, supporting heavy component such as PWR steam generator with large capacity energy absorbing supports under the sponsorship of Ministry of Economical Trade and Industry. If energy absorbing supports are adopted for NPP heavy components, support structure of facility will be much simplified due to their seismic energy absorbing effect. The paper describes the results of lead damper element test and seismic test at Tadotsu Laboratory, using 1/2.5 scale PWR Steam Generator model supported by Lead Extraction Damper (LED) and development of characteristics evaluation formula of energy absorbing support. (author)
From its inception in 1977, the U.S. Department of Energy (DOE) has been responsible for maintaining the nations nuclear stockpile, leading the country in terms of basic research, setting national energy goals, and managing thousands of individual programs. Despite these gains, however, the DOE research and development (R&D) model does not appear to offer the nation an optimal strategy for assessing long-term energy challenges. American energy policy continues to face constraints related to three "Is": inconsistency, incrementalism, and inadequacy. An overly rigid management structure and loss of mission within the DOE continues to plague its programs and create inconsistencies in terms of a national energy policy. Various layers of stove-piping within and between the DOE and national labo...
This report describes the empirical research into barriers to energy efficiency in the German higher education (HE) sector. It is one of nine such reports in the BARRIERS project. The report contains description and analysis of six case studies of energy management in German universities. The results are analysed using the theoretical framework developed for the BARRIERS project (Sorrell et al., 2000). The report also provides brief recommendations on how these barriers to the rational use of energy (RUE) may be overcome and how energy efficiency within the sector may be improved. The results of the study for the higher education sector in Germany are summarised in this executive summary under the following headings: - Characterising the higher education sector; - Case studies of energy management in the German higher education sector; - Evidence of barriers in the German higher ...
Energy-filtered X-ray photoemission electron microscopy (EXPEEM) is a microscopy technique which has the potential to provide surface chemical mapping during surface chemical processes on the nanometer scale. We studied the possibilities of EXPEEM using a Wien filter type energy analyzer in the high energy X-ray region above 1000 eV. We have successfully observed the EXPEEM images of Au islands on a Ta sheet using Au 3d_5_/_2 and Ta 3d_5_/_2 photoelectron peaks which were excited by 2380 eV X-rays emitted from an undulator (BL2A) at Photon Factory. Our recent efforts to improve the sensitivity of the Wien filter energy analyzer will also be discussed.
Environmental pollution has become a bottleneck for the sustainable economic development of China. A 'business-as-usual' energy system in Chian is not suitable for meeting sustainability needs. It is well known that China has to use coal as the main primary energy source over the long term. Under such special conditions, to plan and construct an integrated sustainable energy system with optimal benefits in resource and energy utilization and environmental emissions is urgent. By introducing international studies and new developments in sustainable energy systems, this paper puts forward the concept that a polygeneration strategy based on coal gasification is the trend for future development of China's domestic energy industry. The framework of a polygeneration system based on oxygen-blown gasification is described and its benefits are ...
Full text.The electric energy demand in Lebanon is estimated to grow at an average of 3-5% per year for the coming 10 years. Such an increase in energy demand is problematic for Lebanon since its economy is almost totally dependent on imported fuel which contributes to 97% of the overall energy requirements. Solar water heaters (SWH) are regarded as the most important element in a long term energy conservation and management strategy for this country, but their promotion is a national issue requiring the participation of many stake holders and decision makers. Additionally, the success of solar energy penetration into the existing energy market is constrained by many factors such as technical and financial limitations, decision criteria and policy instruments. This paper will explore the feasibility of SWH, and will work out, using the Analytic Hierarchy Process ...
Many of the vulnerabilities to Energy Access, Energy Security, and Environmental Sustainability result from impediments to reaching a global demand-supply balance, as well as local balances, for various energy sources and carriers. Vulnerabilities result from multiple reasons: regional imbalances of energy production and consumption, the bulky character of the majority of energy fuels, the virtual necessity of electricity consumption following its production, among others. To detect and prioritize respective 'bottlenecks' across energy carriers, they have to be measured. In this report, production, consumption, exports, and imports were measured across all major energy carriers for seven key regions of the world for three time frames-2008, 2020, and 2050. Imbalances between production and consumption form bottlenecks in ...
Visits were made to selected manufacturing units with 25 or more employees. Information was gathered on energy consumption and advice was given on the opportunities available for improving the efficiency of energy use. Potential energy savings are estimated and recommendations are made on the action that should be taken to improve the efficiency of energy use. In the footwear industry space heating controls, improvements in boiler plant and steam services along with building insulation provide most of the savings potential. In the leather industries major energy saving opportunities can be found in low-temperature drying, and heat recovery, where the use of heat pumps could contribute substantial savings in drying and process water heating. Boiler controls and good housekeeping are areas where firms can make worthwhile savings at very little capital cost. (MCW)
Southern California Gas Co.`s (SoCalGas) Energy Resource Center (ERC) in Downey, Calif. is a 45,000 ft{sup 2} (4,181 m{sup 21}) conference and education center created to help energy decision-makers find the most energy-efficient, cost-effective and environment-sensitive solutions to their energy requirements. The center has 36,000 ft{sup 2} (3,344 m{sup 2}) of remodeled space and 9,000 ft{sup 2} (836 m{sup 2}) of new space, all designed to showcase the latest energy-efficient and environment-sensitive technologies. The building is one of the 25 buildings in the US to be designated as Energy Star Showcase buildings by the US Environmental Protection Agency.
We have developed an energy-extension method of a Bragg curve counter (BCC) at the high-energy end for the measurements of double-differential cross-sections (DDXs) of fragment productions induced by tens of MeV protons. In this method, we estimate the incident energies of the fragments penetrating a BCC on the basis of the energy loss and atomic number (Z). We applied this method to the DDX measurements of the {sup nat}C(p, Li) and {sup nat}C(p, Be) reactions induced by 70 MeV protons. The validity of this method has been confirmed by comparing the DDXs of beryllium with theoretical predictions of the PHITS code and the two-body kinematics. This method improves the energy acceptance of the BCC for light fragments twice as wide as that of a conventional method without remodeling of the BCC and any loss of the original advantages.
Energy use patterns and utilisation efficiencies in 40 factories producing palm kernel oil (PKO) in southwestern part of Nigeria were studied. The factories were stratified into small, medium and large scale categories based on the mode of operations and production capacities. Questionnaires were administered on the factories to obtain historical data on petrol, diesel and electricity consumption and PKO production outputs for seven years (1998-2004). Energy use efficiency indicators employed include: energy intensity (EI), energy cost per unit product (EC/P), energy ratio (ER), food energy ratio (FER) and percentage oil yield by weight. Results of the study indicated that averagely, 0.58, 0.53 and 0.74GJ/103l of PKO were needed in the small, medium and large PKO factories, respectively. T...
Detailed, complete, timely and reliable statistics are essential to monitor the energy situation at a country level as well as at an international level. Energy statistics on supply, trade, stocks, transformation and demand are indeed the basis for any sound energy policy decision. For instance, the market of oil -- which is the largest traded commodity worldwide -- needs to be closely monitored in order for all market players to know at any time what is produced, traded, stocked and consumed and by whom. In view of the role and importance of energy in world development, one would expect that basic energy information to be readily available and reliable. This is not always the case and one can even observe a decline in the quality, coverage and timeliness of energy statistics over the last few years.
An energy saving dc-dc converter circuit is disclosed having two energy efficient means which operate in tandem, an energy conserving means and a voltage doubling means. These energy efficient means are applied in combination with elements commonly found in dc-dc converter circuits, namely an ac voltage generator, a transformer for stepping up the generated ac voltage, and means for storing the converted dc voltage. The energy conserving means is connected to the dc voltage storage means. It comprises a resettable inhibit circuit which cuts off the provision of dc voltage for conversion for a predetermined interval when the output of the converter exceeds a predetermined level. The voltage doubling means is reponsive to outputs of the inhibit circuit of the energy conserving means and the ac voltage generator. It provides a phase inverted waveform of the ...
Geothermal energy appears as a viable economic alternative among the different renewable energy sources. The French bureau of geological and mining researches (BRGM) is involved in several research and development programs in the domain of geothermal energy and underground reservoirs. This document presents the content of 5 programs: the deep hot dry rock system of Soultz-sous-Forets (construction and testing of the scientific pilot, modeling of the reservoir structure), the development of low and high enthalpy geothermal energy in the French West Indies, the comparison of the geothermal development success of Bouillante (Guadeloupe, French West Indies) with the check of the geothermal development of Nyssiros (Greece) and Pantelleria (Italy), the development of the high enthalpy geothermal potentialities of Reunion Island, and the underground storage of CO{sub 2} emissions in geologic formations (deep ...
This report summarizes all work of the Limited Energy Study, Energy Engineering Analysis Program (EEAP), Fort Hunter Liggett, California, authorized under Contract Number DACA05-92-C-0155 with the U.S. Army Corps of Engineers, Sacramento District, California. The purpose of this study is to develop projects and actions that will reduce facilities energy consumption and operating costs at Fort Hunter Liggett. Implementation of these projects will contribute to achieving the goal of the Army Facilities Energy Plan of a reduction in energy consumption per square foot of building floor area of 20 percent by FY2000 from FY1985 baseline levels.
Summary Dietary fibres are believed to reduce subjective appetite, energy intake and body weight. However, different types of dietary fibre may affect these outcomes differently. The aim of this review was to systematically investigate the available literature on the relationship between dietary fibre types, appetite, acute and long-term energy intake, and body weight. Fibres were grouped according to chemical structure and physicochemical properties (viscosity, solubility and fermentability). Effect rates were calculated as the proportion of all fibre-control comparisons that reduced appetite (n-=-58 comparisons), acute energy intake (n-=-26), long-term energy intake (n-=-38) or body weight (n-=-66). For appetite, acute energy intake, long-term energy intake and body weight, there were cl...
Energy consumption is a perennial issue in the design of wireless sensor networks (WSNs) which typically rely on portable sources like batteries for power. Recent advances in ambient energy harvesting technology have made it a potential and promising alternative source of energy for powering WSNs. By using energy harvesters with supercapacitors, WSNs are able to operate perpetually until hardware failure and in places where batteries are hard or impossible to replace. In this paper, we study the performance of different medium access control (MAC) schemes based on CSMA and polling techniques for WSNs which are solely powered by ambient energy harvesting using energy harvesters. We base the study on (i) network throughput (S), which is the rate of sensor data received by the sink, (ii) fair...
This article examines reported willingness to pay for electric utility investments in renewable energy and energy efficiency resources using the results of Deliberative Polls conducted by electric utilities in Texas. Age, education, and salary tend to affect reported willingness to pay for utility investments in these resources. Intensive exposure to information about energy resource issues led to an increase in the number of respondents interested in paying a modest premium to support investments in both renewable energy resources and energy efficiency. However, average reported premiums actually declined following the Polls, as very high outlier responses moved to more reasonable values following the Polls. These results support the contention that informed dialogue about energy alternatives will result in broader interest in providing a modest level of ...
The main sources of energy that might be available in remote low populated areas of Libya are either diesel generating units or wind mills for water pumping. Several problems in the working performance of these two types of energy production may arise due to environmental conditions. Direct conversion of solar energy can replace other ways of energy delivery or production, especially in this country where the solar radiation all year is relatively high. Direct conversion of solar energy is relatively expensive, however the cost of erecting long feeders and supervising them may be much more expensive than the usage of solar systems. This paper investigates the economics associated with either solutions of energy production. A case study is given in detail to supply one of the remote areas with a population of about 250. (author)
Today's building industry is promoting the use of renewable sources of energy to heat, cool, and illuminate commercial buildings. Societies such as the International Solar Energy Society sponsor conferences such as this one to share knowledge and experience in the area of solar energy. However, the technologies presented here assume a need for heating, cooling or illumination. A simple technique is presented for determining the actual heating, cooling, and lighting requirements for commercial buildings, and for reducing those requirements through proper building design before applying solar technologies. The energy nomographs are a graphic energy design tool developed to aid designers in making cost effective decisions about energy alternatives early in the design process. Reducing loads at this point can help reduce the expense of a passive or active ...
The study of the {alpha}-particle energy distributions associated with ND and SD states in {sup 151,152}Dy has been carried out. The Dy isotopes were produced in the reaction {sup 37}Cl+{sup 123}Sb at 191 MeV via the ({alpha}5n) and ({alpha}4n) channels, respectively. In {sup 151}Dy the {alpha}-particle energy distributions associated to ND and SD are very different from each other, both at the low and high energy sides inducing a difference of 3 MeV in the {alpha}-particle mean energy. In {sup 152}Dy the situation is different; the {alpha}-particle spectral shapes are similar and a difference in the {alpha}-particle mean energy of only 0.7 MeV is deduced. A description in terms of energy localization of entry states is given. (orig.)
A closed economic system was assumed for the Veneto Region (Italy) in order to define an appropriate input-output model and assess the future economic and environmental impacts of proposed actions for energy source development and economic growth. Present and forecasted energy demands (to the year 2000) were determined by energy source, e.g., natural gas, coal, petroleum and hydropower for the different consuming sectors - agriculture, transportation, industry, etc. Forecasts were made of the air pollution expected as a result of different types of energy and technology inputs for each sector. These considered planned retrofits towards clean combustion systems. Costs were estimated for the implementation of proposed pollution abatement measures, as well as, for the effects of energy use related environmental damage and measures to restore the environment. Some of the factors taken ...
We calculated the energies of asymmetric nuclear matter at zero and finite temperatures with the cluster variational method. At zero temperature, the expectation value of the two-body Hamiltonian composed of the kinetic energies and the AV18 two-body forces is calculated with the Jastrow wave function in the two-body cluster approximation. The obtained two-body energy is in good agreement with the result with the Fermi Hypernetted Chain (FHNC) calculation by Akmal et al. The energy caused by the UIX three-body forces is treated somewhat phenomenologically so that the total energy reproduces the empirical saturation point. Furthermore, the parameters included in the three-body energy are readjusted so that the Thomas-Fermi (TF) calculations with use of the obtained energy of nuclear matter reproduce the gross feature of the experimental data ...
Energy savings performance contracting (ESPC) is now receiving greater attention as a means of implementing large-scale energy conservation projects in housing. Opportunities for such projects exist for military housing, federally subsidized low-income housing, and planned communities (condominiums, townhomes, senior centers), to name a few. Accurate prior (to construction) estimates of the energy savings in these projects reduce risk, decrease financing costs, and help avoid post-construction disputes over performance contract baseline adjustments. This paper demonstrates an improved method of estimating energy savings before construction takes place. Using an engineering model calibrated to pre-construction energy-use data collected in the field, this method is able to predict actual energy savings to a high degree of accuracy. This is verified with ...
Energy savings performance contracting (ESPC) is now receiving greater attention as a means of implementing large-scale energy conservation projects in housing. Opportunities for such projects exist for military housing, federally subsidized low-income housing, and planned communities (condominiums, townhomes, senior centers), to name a few. Accurate prior (to construction) estimates of the energy savings in these projects reduce risk, decrease financing costs, and help avoid post-construction disputes over performance contract baseline adjustments. This paper demonstrates an improved method of estimating energy savings before construction takes place. Using an engineering model calibrated to pre-construction energy-use data collected in the field, this method is able to predict actual energy savings to a high degree of accuracy. This is verified with ...
This document gathers the presentations given at the first French national meetings of solar energy for the development of solar systems in buildings. The meeting was organized over two days. The first day comprises 4 workshops about: urbanism and planning, cultural acceptability of solar energy in buildings (the OPAC 38 housing association, point of view on an energy information point, the Freiburg (Germany) solar region and marketing examples), technical integration to the structure (Clipsol solutions), and economical criteria (compared impacts of R and D public photovoltaic programs (USA, Japan, Germany, France, Italy), financing of rehabilitation projects, global approach of solar photovoltaic energy, technical solutions and strategy of products development, why and how to make an economical analysis of solar energy applications in the building industry). The second day ...
In Canada, the cost of heating is a major expense in the operation of greenhouses in the winter season, inhibiting greenhouse production in winter months in most part of the country. Alternative energy sources, such as solar energy and biomass energy may offer an economically feasible heating alternative. A solar energy greenhouse technology developed in northern China for winter vegetable production has demonstrated good potential for Manitoba winter conditions. The design and performance of solar energy greenhouses depend on the geographical location. Therefore, in order to optimize the design of solar greenhouses with respect to the latitude of the location for maximum solar radiation gain, a theoretical analysis was performed that analyzed parameters such as greenhouse length and the roof slope. This paper described the methodology of the study, including a description of solar ...
This report deals with the renewable energies and the local development called the territory intelligence in action. Taking into account the place of the electricity in the french energy accounting and the part of the nuclear in its production, the local authorities have to act in the heat domain, which is the first energy need in France, far in front of the specific electricity (those which cannot be replace by other type of energy). But 80% of the heat is today covered by fossil energies. No actions to change this situation will be done without a real implication of the local government. The authors preconize an ambitious objective: cover 50% of the heat needs from renewable energies in the next generat This objective must rely on a program called ''alternative energies''. In this framework the authors ...
Recognizing the importance of energy as a vital component in economic development, the Taiwanese government has been continuously revising its energy policy, seeking to balance economic development, energy supply, and environmental protection (3E). Some measures, in an attempt to achieve the 3E balance, were previously implemented in Taiwan; nevertheless, some unresolved issues departing from certain core principles of Taiwan's sustainable energy policy and an international initiative for a low carbon society remain. The aim of this paper is to examine the energy supply and demand structure of Taiwan and the present status of individual energy carriers (including coal, petroleum, natural gas and electricity). In addition, it investigates the current energy policy framework and its implementation in Taiwan, identifies unresolved issues ...
The purpose of this study is to develop projects and actions that will reduce facilities energy consumption and operating costs at Fort Hunter Liggett. Implementation of these projects will contribute to achieving the goal of the Army Facilities Energy Plan of a reduction in energy consumption per square foot of building floor area of 20 percent by FY2OOO from FY1985 baseline levels, There are 205 numbered structures at Fort Hunter Liggett, containing a total of 791,034 square feet of gross floor space. This United Energy Study evaluates 52 surveyed buildings with results extended to an additional 44 identical or similar buildings. Together, these buildings contain a total of 632,386 gross square feet and account for approximately 93 percent of overall energy usage. Present Energy Consumption Total energy consumption at Fort Hunter Ligett in ...
Geothermal energy is one of the more promising renewable energy technologies because it is environmentally benign and, unlike most renewable energy sources, can provide base power. This report provides an assessment of the research and development (R&D) work underway in geothermal energy in the following countries: Denmark, France, Germany, Italy, Japan, Russia, and the United Kingdom. While the R&D work underway in the US exceeds the R&D efforts of the other countries, the lead is eroding. This erosion is due to reductions in federal government funding for geothermal energy R&D and the decline of the US petroleum industry. This erosion of R&D leadership is hindering commercialization of US geothermal energy products and services. In comparison, the study countries are promoting the commercialization of their geothermal ...
Due to the recent catastrophic energy system failures in California along with those in the North-Eastern US and Southern Canada, London, and Italy, the time has come to proclaim the failure of deregulation, privatization or liberalization and propose a new energy system. This book shows in the first section, how five precipitating forces led to the deregulation debacle in California: (1) major technological changes and commercialization, (2) regulatory needs mismatched to societal adjustments, (3) inadequate and flawed economic models, (4) lack of vision, goals, and planning leading to energy failures, and (5) failure and lack of economic regional development. The second half of the book, examines how 'civic market', new economic models, and planning for complexity as sustainable economic development transformed in California, the same five forces to create an 'agile energy ...
Examines thermal coal demand in Japan covering: trends in energy demand; long-term outlook for energy supply and demand; coal-fired power development plan and the outlook for steam coal demand; and the prospects for Asian steam coal demand and coal procurement. Total energy consumption is expected to increase by 1.0% per annum to 2000 and thereafter 0.9% per annum until 2010. This is based on the assumption that measures to encourage energy conservation and improve energy efficiency are implemented. 3 figs., 2 tabs.
Discusses the resolution of the 2. Congress of the Polish Nuclear Society on the energy situation in Poland and recommendations for energy policy. Recommendations for use of nuclear power plants in Poland are made considering environmental pollution from coal combustion (air pollution by sulfur dioxide, nitrogen oxides and carbon dioxide as well as water pollution by salt from mine water discharged to rivers), development of the Polish economy, forecast increase in energy consumption and the role of nuclear energy in other European countries. Research on nuclear power plants, safety and environmental aspects as well as comparative efficiency of coal-fired power plants and nuclear power plants is evaluated.
This paper explores the feasibility of integrating energyefficiency program evaluation with the emerging need for the evaluationof programs from different "energy cultures" (demand response, renewableenergy, and climate change). The paper reviews key features andinformation needs of the energy cultures and critically reviews theopportunities and challenges associated with integrating these withenergy efficiency program evaluation. There is a need to integrate thedifferent policy arenas where energy efficiency, demand response, andclimate change programs are developed, and there are positive signs thatthis integration is starting to occur.
Energy deposition process by relativistic fast electrons produced by ultra-intense laser pulses is discussed. The process is calculated with a two dimensional Fokker-Planck simulation code including binary and collective collisions coupled with electromagnetic field. We focused on Velocity Distribution Function (VDF) dependence in the simulation. The results show that the spread angle of the fast electrons distribution affects energy deposition area and deposited energy is concentrated in the vicinity of the propagation axis of the fast electrons. It may be also suggested that self-pinch effect of a fast electron beam causes large deposition energy. (author)
The following Resolution has been stated because of the results of the workshops Elaboration of proposals for strategic guidelines held from 2 to May 5, 2006, elaboration of proposals for the Strategic Lines instruments held from 24 to July 28, 2006, as well as documents Proposal of politic energetic Uruguayan Energy Sector development and proposal of Energy Policy Instruments developed by the National Directorate of Nuclear Energy and Technology and the Energy Strategy Guidelines Uruguay 2006.
Using the past diffusion trends of four renewable energy technologies for irrigation water pumping in India (SPV pumps, windmill pumps and biogas/producer gas driven dual fuel engine pumps), results of an attempt to project their future dissemination levels, have been presented in this study. The likely contribution of the renewable energy options considered in the study to the projected energy demand for irrigation water pumping in India has been estimated. Estimates of the associated investment requirements taking into account the learning effect have also been presented. (author)
In the rural areas, especially those located far enough from infrastructure facilities (highways and national roads, electricity and gas networks, etc.), energy supply (both quantitatively and qualitatively) is scarcer than in the urban ones. The purpose of this paper is to analyse the use of renewable energy hybrid systems in order to increase the quality and the quantity of energy supplied to the rural settlements. The paper is thus a guide of how to choose the appropriate energy source with higher potential and efficiency, minimal capital and operational costs and better comfort. (authors)
Nuclear energy related research in Switzerland is concentrated at PSI's Nuclear Energy and Safety Research Department (NES). The activities of the department are concentrated on three main domains of: Safety and related problems of operating plants; safety features of future reactor and fuel cycles; waste management. Comprehensive assessments of energy systems are carried out in cooperation with PSI's General Energy Research Department. Many of the programs are part of collaborations with universities, industry, or international organisations. Progress in 2000 in these topical areas is described in this report. A list of scientific publications in 2000 is also provided.
Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.
Energy conservation and local energy deposition are investigated in the context of coupled-particle (i.e., neutrons, gamma rays, and charged particles) transport analysis. For charged particles, the concept of group splitting the 1 = 0 transfer matrix to ensure both particle and energy conservation is introduced. Although these procedures are more complex than those found in the usual neutron or coupled-neutron gamma-ray problem, they yield a consistent approach for the calculation of local energy deposition.
Contract No. DACA 90-8l-C-oo72 directs that a basewide energy study be accomplished for the Mannheim and Pirmasens Military Communities, Federal Republic of Germany. The project is identified as Energy Engineering Analysis Program (EEAP) Package No. 5. The overall objective of the study is to produce a systematic plan of improvement projects that will reduce by 1985 the energy consumption in compliance with the Army Facilities Energy Plan without decreasing the readiness posture of the Army.
Multi-machine experimental observations indicate resilience in the temperature profiles at low pedestal temperatures,whereas at high pedestal temperatures the profile stiffness seems to disappear.The change of the profile behavior impacts the energy confinement,basically due to a strong non-linear dependence of the energy transport on the pedestal temperature together with different critical conditions for the onset of turbulence in the ions and electrons.This possible explanation for the different observations is based on the assumption that both ion and electron energy transport is governed by turbulence which sets in at a critical temperature gradient as well as on a significant energy equipartition between electrons and ions.
In a free electron laser (FEL), the electron bunch energy profile at the undulator entrance can have temporal structures. In this paper, we derive analytical expressions for the FEL in the undulator, in the case of the electron bunch having both energy chirp and energy curvature. The FEL properties are studied analytically by convoluting a Gaussian seed laser with the FEL Green's function obtained by solving the coupled Vlasov-Maxwell equations. In particular, for different ratios of the temporal duration of the seed laser and that of the Green's function, interesting behavior is revealed.
The central nervous system (CNS), generally accepted to regulate energy homeostasis, has been implicated in the metabolic perturbations that either cause or are associated with obesity. Normally, the CNS receives hormonal, metabolic, and neuronal input to assure adequate energy levels and maintain stable energy homeostasis. Recent evidence also supports that the CNS uses these same inputs to regulate glucose homeostasis and this aspect of CNS regulation also becomes impaired in the face of dietary-induced obesity. This review focuses on the literature surrounding hypothalamic regulation of energy and glucose homeostasis and discusses how dysregulation of this system may contribute to obesity and T2DM.
Most K-12 schools could save 25% of their energy costs by being smart about energy. Nationwide, the savings potential is $6 billion. While improving energy use in buildings and busses, schools are likely to create better places for teaching and learning, with better lighting, temperature control, acoustics, and air quality. This brochure, targeted to school facilities managers and business officials, describes how schools can become more energy efficient.
The paper considers the main components of energy policy, in particular the challenges of network security of supply, long-term contracts and the environmental constraints. It is argued that the United Kingdom's energy policy should take account of multiple market failures and context dependent. Given energy liberalisation in the 1980s and 1990s, it is argued that interventions based upon market-based instruments should be given greater importance. Institutional reform to reflect the shift in focus towards investment in non-carbon technologies and the security issues associated with networks is proposed, notably the creation of an energy agency. 15 refs., 2 figs.
The present volume provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD Countries. It covers the years 1970 to 1982 year by year and includes many revisions and additions to data previously published. The balances in the present volume are based on data published in OECD Energy Statistics 1971-1981 and OECD Energy Statistics 1981-1982. Tables for each OECD Country include production, import, export, consumption by the different industries, transportation, agriculture, residential sector of the different energies: solid fuels, petroleum, gas, nuclear power and hydroelectricity.
This document provides guidance for modeling and inspecting energy-efficient property in commercial buildings for certification of the energy and power cost savings related to Section 179D of the Internal Revenue Code enacted in Section 1331 of the 2005 Energy Policy Act and noted in Internal Revenue Service Notice 2006-52. Specifically, Section 179D provides federal tax deductions for energy-efficient property related to a commercial building's envelope; interior lighting; heating, ventilating, and air conditioning; and service hot water systems.
This document provides guidance for modeling and inspecting energy-efficient property in commercial buildings for certification of the energy and power cost savings related to Section 179D of the Internal Revenue Code enacted in Section 1331 of the 2005 Energy Policy Act and noted in Internal Revenue Service Notice 2006-52. Specifically, Section 179D provides federal tax deductions for energy-efficient property related to a commercial building's envelope; interior lighting; heating, ventilating, and air conditioning; and service hot water systems.
The authors use a Glauber multiple-collision model to examine the dynamics of nucleus-nucleus collisions. The model introduces a stopping law, which describes how a baryon loses energy in a baryon-baryon collision, and a particle production law, which is based on the baryon energy loss. The model gives results on the longitudinal energy loss which compare well with the recent WA80 experimental data for /sup 16/O on various targets at 60 and 200 GeV per nucleon. The stopping law that is needed to fit the experimental zero-degree spectra reveals that the degree of stopping in these high-energy nuclear collisions is high.
Renewable energy systems (RES) are unique among energy supply systems because their performance and design depends entirely on the location and climatic conditions. As a result of design options, user requirements and local climatic conditions, there are enormous variations between RES. This paper describes a method how to evaluate the data on monitored renewable energy systems (RES) in such a way that the operating conditions and performance of individual components and the system as a whole can be analysed and compared. It shows how categories of similar use can be defined and recommendations for each category can be made to assist in the selection of the most suitable products. (orig.)
Purpose of this assessment for this town in the Slovak Republic is to develop information on the building sector energy efficiency and improvement potential for use by town management to support decisions on providing energy services to Handlova citizens. Objectives were to characterize baseline space and water heat energy use and efficiency improvement potential in the residential and nonresidential building sectors. Intention was to identify major areas of efficiency improvement potential and cost-effectiveness. Four levels of energy and fuel prices were used. A significant efficiency resource exists in the space and water heating end uses in these building sectors; it amounts to 42% of the total building sector space and water heat energy consumption.
A new scheme of the longitudinal emittance measurement for high energy negative ion beam is proposed. The energy distribution of the detached electron from the negative ions by the photodetachment process, if the photon energy is almost equal to the electron binding energy of the negative ion (=electron affinity of the atom), reflects that of the original negative ions. Therefore, by introducing the photon in a short width comparing with the bunch width of the negative ion beam, the longitudinal energy distribution of each phase of the beam, that is the longitudinal emittance, can be measured. (author).
Since the late nineties, an energy control standardisation steering body was set up at the AFNOR, prompted by the French administration and ADEME which is chairing it. That body, which became a forum in 2006 brings together stakeholders in various areas concerned by that issue (industries, construction, transport, environment, services,...) as well as the representatives of main companies, professional organisations and standardisation operators acting in the area / of energy in France. Its purpose is to help exchange information and express needs in terms of standardisation in the area of energy and energy efficiency. On its initiative, the European standardisation committees CEN and CENELEC set up in 2002 an equivalent body responsible for the strategic coordination of their energy management programmes and entrusted the steering to our country (ADEME chairing, AFNOR secretariat). ...
The spectral energy-dependence of the radiation-induced ESR signal has been studied in ovine cortical bone. Crushed bone samples were irradiated using photon beams with effective energies in the range from 0.06 to 6 MeV, and electron beams with mean energies in the range from 2 to 10 MeV. The photon and electron data were normalized to a dose to bone of 50 Gy and the results are reported as response relative to the ESR signal for photon irradiation at 1.25 MeV ("6"0Co). The photon irradiation results show that the ESR response is greatest at low energies with a relative value of 1.2 at 0.06 MeV. The relative response decreases, as the energy increases, to approximately 0.85 in the region of 2 to 3 MeV. These variations in the relative ESR responses are significantly less than the ESR energy-dependent responses reported in the literature for human tooth enamel ...
This work, carried out by the parliamentary office for the evaluation of scientific and technological choices on request of the French National Assembly and Senate, takes stock of the present day situation and technical perspectives of development of renewable energy sources and of research needs of the French industry in this domain: 1 - renewable energies: key-technologies for the energy supply of developing countries and for a rational consumption in transportation systems and accommodations of developed countries (energies technically different from fossil or nuclear energies; fundamental energy sources for a developing world; different national goals in Europe depending on the available natural resources and on the political realities; a minor interest in France for the domestic power generation but a major interest for transports, residential and tertiary ...
In many facilities, energy management is simply a matter of managing the energy required for lighting and space conditioning. In many others, however, energy management is much more complex and involves large motors and controls, industrial insulation, complex combustion monitoring, unique steam distribution problems, significant amounts of waste heat, etc. Typical facilities offering large energy management opportunities include industrial facilities, large office and commercial operations, government institutions such as schools, hospitals and prisons. Such facilities generally have specialized industrial, commercial or institutional processes that incorporate many of the concepts covered in other chapters. These processes require thorough analytical evaluations to determine the appropriate energy-saving measures. This chapter provides some examples. In this chapter the authors ...
Energy is a critical factor which determines the progress of rural development. Energy is therefore an area of concern. The quality, availability and cost of conventional energies, plus the associated environmental effects are a growing problem - not only for the health infrastructure but also for agriculture and domestic life. This is true not only in developing countries where the fast growing industries and urban populations demand a soaring proportion of available energy at the expense of the rural communities, but also in the poorest countries with weak energy infrastructure. Renewable energies, much studied in the last 20 years, can meet the needs of rural health and education services and communities by providing high quality, low cost, non-polluting energy. Solar energy, in particular, has the flexibility to ...
Coal output in China increased from 872mt in 1985 to 1080mt in 1990, representing an annual growth rate of 4.37% . As the biggest coal burning country, it gives out a large amount of CO_2 and other pollutants into air, resulting in serious air pollution and sharing a great part in creating the global greenhouse effect. On the other hand, China faces severe energy shortage. Coal will remain the most important energy resource for a long time, Using the method of econometrics, this paper analyses the relations between China's energy production, consumption increase and national economic growth in the list forty years, makes comparisons with other countries, and points out problems of China's energy consumption increase and economic development. On this basis the strategy for developing China's energy industry is put forward, In the end, the authors advance that the leading position of ...
In 1986, the National Research Council, through its Energy Engineering Board, formed the Committee on Geothermal Energy Technology. The committee's study addressed major issues in geothermal energy technology, made recommendations for research and development, and considered cooperative arrangements among government, industry, and universities to facilitate RandD under current severe budget constraints. The report addresses four types of geothermal energy: hydrothermal, geopressured, hot dry rock, and magma systems. Hydrothermal systems are the only type that are now economically competitive commercially. Further technology development by the Department of Energy could make the uneconomical hydrothermal resources commercially attractive to the industry. The economics are more uncertain for the longer-term technologies for extracting energy from ...
The purpose of this solar energy project was to design, manufacture, install, maintain and evaluate solar heating systems in order to stimulate community acceptance of the practicality of solar applications, reduce non-renewable energy resource consumption, and decrease residential expenditures for energy. The project also provided skill training and experience for CETA employees in the design, manufacture, and installation of solar energy equipment systems. CDC's contract had four separate solar energy projects; namely: Domestic Water Heating Systems for four Single-Family Homes; Domestic Water Heating for an industrial building; Domestic Water Heating for a (4) unit apartment complex (includes (12) supplemental space heating units); and Integral Passive Water Heaters and Energy Conservation Devices for (8) one bedroom homes. CDC staff designed all ...
In electron beam therapy, tissue overdose due to electrons backscattered from lead has been profusely studied. To quantify this dose enhancement effect, an electron backscatter factor (EBF) wasdefined as the ratio of dose at the tissue-inhomogeneity interface with and without the scatterer present. The dependence of the EBF on energy at the scatterer surface is not well known for energies lower than 3 MeV which is the most frequent clinical situation. In this work, we have done Monte Carlo calculations with the GEANT code to study EBF in lead at this energy range. The applicability of this code and the developed procedure for dose estimation has been experimentally verified. The dependence of the EBF on the beam energy incident on the scatterer has been studied for different nominal beam energies incident at the phantom's surface. The results show a trend of increase of EBF ...
The steady state surfaces of ion bombarded 3C-, 4H- and 6H-SiC samples were studied by means of reflected electron energy loss spectroscopy (REELS). The REELS exhibit a well-defined loss peak in the region of about 20 eV. The position of the maximum of the loss peak depends on the bombarding ion energy (decreasing with increasing ion energy), and on the primary electron beam energy (increasing with increasing primary energy). This behavior can be explained if we suppose that the plasmon energy in the altered layer (produced by ion bombardment) is different from that of the unaltered bulk. In this case the measured loss peak is the sum of two overlapping plasmon peaks. With modeling the system as a homogeneous altered layer and a homogeneous unaltered substrate the plasmon energy in the altered layer was derived to be 19.8 eV. The large ...
Renewable energy sources have been attracting the attention of a sensitized public since general pollution abatement measures have been taken, since efforts have been going into the protection of the earth atmosphere, the preservation of the vital ozone layer, and the conservation of fossil energy sources, and since nuclear power risks have been recognized and discussed. In addition to wind power and solar energy solid biomass, e.g. wood, wood wastes, vegetable residues and plants cultivated for the purpose of energy production, is among the topical alternatives. Agriculture and silviculture are important end-users of potential decentralized energy supplies and are cut out for supplying biomass for energy utilization. Additional income sources will open up for farmers. Based on these facts this KTBL working paper describes the biomass energy ...
Launched in 2006, over 8,700 residential energy upgrades have been completed through Austin Energy's Home Performance with Energy Star (HPwES) program. The program's lending partner, Velocity Credit Union (VCU) has originated almost 1,800 loans, totaling approximately $12.5 million. Residential energy efficiency loans are typically small, and expensive to originate and service relative to larger financing products. National lenders have been hesitant to deliver attractive loan products to this small, but growing, residential market. In response, energy efficiency programs have found ways to partner with local and regional banks, credit unions, community development finance institutions (CDFIs) and co-ops to deliver energy efficiency financing to homeowners. VCU's experience with the Austin Energy HPwES program ...
Greenhouse gas mitigation strategies are generally considered costly with world leaders often engaging in debate concerning the costs of mitigation and the distribution of these costs between different countries. In this paper, the analyses and results of the design of a 100% renewable energy system by the year 2050 are presented for a complete energy system including transport. Two short-term transition target years in the process towards this goal are analysed for 2015 and 2030. The energy systems are analysed and designed with hour-by-hour energy system analyses. The analyses reveal that implementing energy savings, renewable energy and more efficient conversion technologies can have positive socio-economic effects, create employment and potentially lead to large earnings on exports. If externalities such as health effects are included, even more benefits can ...
This document is an executive summary of the colloquium organized by the French syndicate of renewable energies (SER) which took place at the Maison de l'UNESCO in Paris during the national debate on energies organized by the French government in spring 2003. The colloquium was organized around 6 round tables dealing with: the world perspectives and the environmental context of the contribution of renewable energies to the sustainable development (respect of Kyoto protocol commitments, contribution to the security of energy supplies, lack of large scale program of development of decentralized power generation in developing countries, lack of market tools linked with CO{sub 2} emissions, improvement of competitiveness); development of renewable energies in Europe (promotion and sustain in all European countries, obligation of supply and purchase, pricing regulation, European ...
Climate change is no longer questioned. Meeting growing global energy needs - while limiting the rate of climate change over the long term - will require both developed and developing countries to move to fuels with lower emissions of greenhouse gases and to adopt more energy-efficient technologies. Investment decisions made today will be pivotal in determining the path of global energy consumption for decades to come. Energy markets, financial markets, and the markets in which greenhouse gas emissions are traded - the so-called 'carbon markets' - together determine which technologies are adopted, and how quickly. Over the next half-century, energy demand will grow almost four times as rapidly in developing countries as in developed countries. Consequently, finding ways to increase investment in cleaner energy technologies in rapidly-growing ...
The needs of large industrial, commercial, and institutional energy consumers are more closely connected with the needs of power utilities and energy services companies, a result of the evolving global energy environment. Consumer choice, competition amongst energy suppliers, and increased demand are brought about in some regions by deregulation. Increasingly, large energy consumers expect high levels of quality and reliability from the energy delivered. As a result, management of the cost and the quality of the energy product and the energy assets that produce, deliver, control and consume it requires different strategies. Three major challenges must be overcome: (1) requirement to support economic and efficient delivery, purchasing and use of energy, (2) requirement to guarantee higher levels of ...
We measured neutron time-of-flight spectra from 90 MeV protons and 140 MeV alpha particles bombarding thin targets of Al, Ni, Zr, and Bi at laboratory angles between 20_0 and 135_0. The low-energy (5 to 45 MeV) portions of the spectra were measured with 5 cm diameter by 5 cm deep NE-213 counters at 1 m flight paths with n-#betta# pulse-shape discrimination. The high-energy (35 to 150 MeV) portions of the spectra were measured with 12.7 cm diameter by 10.2 cm deep NE-102 counters at flight paths of 2.0 to 5.0 m. The proton-induced measured neutron spectra reveal three distinct energy regions: a low-energy evaporation region, a high-energy region dominated by the quasifree scattering process, and an intermediate-energy region dominated by multistep, preequilibrium processes. In the latter two regions, the spectra show strong angular dependence. The alpha-particle ...
An intensified integration of renewable energies and a more extensive use of combined heat and power lead to an increasingly decentralized power economy. Such an economy is characterized by the conversion of energy at the point of the energy demand and depending on the energy system, by the possibility of balancing the fluctuating supply of renewable energies. In the long run, there is no doubt that fuel cells will be part of such a sustainable and flexible energy concept. The scope of this dissertation includes an analysis of the flexibility of fuel cells in energy supply (1,5 kW{sub el}), an assessment of the potential to compensate for the fluctuating supply of wind energy by an aggregation of decentralized fuel cells and a participation as a contractor in the spot and balance energy markets. ...
Twenty patients with lesions in the trachea or bronchus underwent energy subtraction Fuji computed radiography (FCR). Images obtained were compared with those from conventional FCR (plain FCR). ''Very clear'' images (in which the contour of the trachea and bronchus could be clearly defined) were obtained in 12/22 (55 %) by energy subtraction FCR and in 3/22 (14 %) by plain FCR; ''clear'' images (in which the contour could be defined) in 9/22 (41 %) by energy subtraction FCR and in 18/22 (82 %) by plain FCR; and ''unclear'' images (in which the contour could not be defined) in 1/22 (5 %) by both methods. Energy subtraction FCR, as well as plain FCR, yielded high image quality for the trachea. Energy subtraction FCR was superior to plain films when tumors existed within the trachea. (Namekawa, K.).
The International Linear Collider (ILC) and other proposed high energy e{sup +}e{sup -} machines aim to measure with unprecedented precision Standard Model quantities and new, not yet discovered phenomena. One of the main requirements for achieving this goal is a measurement of the incident beam energy with an uncertainty close to 10{sup -4}. This article presents the analysis of data from a prototype energy spectrometer commissioned in 2006-2007 in SLAC's End Station A beamline. The prototype was a 4-magnet chicane equipped with beam position monitors measuring small changes of the beam orbit through the chicane at different beam energies. A single bunch energy resolution close to 5 {center_dot} 10{sup -4} was measured, which is satisfactory for most scenarios. We also report on the operational experience with the chicane-based spectrometer and suggest ways of improving ...
Good indoor air quality and thermal comfort, as well as low energy consumption, were achieved in an environment friendly experimental METOP-office building in Espoo, Finland. The consumption of heating and cooling energy was minimized by installation of energy-efficient windows, good CFC-free thermal insulation of the building envelope, the individually-controlled ventilation and room temperatures, heat recovery and energy-storing structures. According to the study carried out in 1990-1993, the heating energy was 13 kWh/m{sup 3}, 60% lower than the average consumption. The index of the satisfaction of thermal comfort was over 90%. Concentrations of all the measured indoor air pollutants were low. Ventilation rates could be chosen in each office room from 10 to 40 dm{sup 3}/s. The noise level of the ventilation system was low and the lighting level was pleasant. (author)
The offshore and inshore wave energy resource in Asturias (N Spain) is studied using wave buoy data and a hindcast dataset spanning 44 years (1958-2001). Offshore average wave power and annual wave energy values are found to exceed 30 kW/m and 250 MWh/m, respectively, at 7 of the 11 study sites. This substantial resource is characterised in terms of the sea states involved. Most of the energy is provided by IV quadrant waves with significant wave heights between 2 m and 5 m and energy periods between 11 s and 13 s. After analysing the offshore resource, numerical modelling is used to investigate the inshore wave patterns. A coastal wave model is validated with wave buoy data and applied to three case studies representative of storm, winter and summer conditions. Inshore wave energy concent...
A set of nomographs to estimate the levelized energy cost for photovoltaic systems are presented. These are designed to assist system designers, analysts, and planners in estimating the effects of research and development and system-design optimization on the delivered cost of energy. The nomographs are based on a refined version of the energy cost estimation equation that appears in the National Photovoltaics Program Five-Year Research Plan. The nomographs have been prepared to emphasize technologies with the potential of producing low-cost energy (<$0.40/kWh levelized in nominal terms or $0.17/kWh in 1982 dollars), and thus primarily apply to far-term or advanced intermediate photovoltaic technologies. Separate sets of nomographs are presented to encompass both flat-plate and concentrator technologies. To supplement the nomographs, a set of tabular solutions of the energy cost ...
An FEL based energy driver for Inertial Confinement Fusion (ICF) is proposed. The key element of the scheme is free electron laser system. Novel technical solutions, namely, using of multichannel, multi-stage FEL amplifier with diaphragm focusing line, reveal a possibility to construct the FEL system operating at radiation wavelength {lambda} = 0.5 {mu}m and providing flush energy E = 1 MJ and brightness 4 x 10{sup 22} W cm{sup -2} sr{sup -1} within steering pulse duration {tau} {approximately} 0.1-2 ns. Total energy efficiency of the proposed ICF energy driver is about of 11% and repetition rate is 40 Hz. It is shown that the FEL based ICF energy driver may be constructed at the present level of accelerator technique R& D.
During the 1990's, natural gas was the energy source with the fastest rate of growth in the world energy balance. Nevertheless, recent evolutions of the energy context, in particular in terms of prices, have had a rather strong impact on the progress of the different energy sources penalizing gas a little. Beyond this competition between energies, which may increase, the medium-term perspectives of natural gas development is in keeping with an environment full of uncertainties. This article presents: the world supply and demand prospects for 2010-2015 (impact of high gas prices on other energy sources, occurrence of production constraints, political decisions of producing countries and world gas industry balance), trends on main markets (North America, Europe, Asia-Oceania), and international trade. (J.S.)
The coherent flucton model is applied to the description of some basic nuclear properties, such as: ground state energies, bond energies, nucleon momentum spectra, and nuclear density distributions. It is shown that the momentum distributions of the nucleons coincide with the Fermi distribution for small momenta and exhibit a well pronounced high energy ''tail'', thus providing inclusive reactions of pi-meson generations in kinematically forbidden areas at nucleon-nucleon collisions. Analytical expressions for the bond energy and nuclear density distribution are derived. An agreement with the experimentally obtained data is achieved. The model features are discussed referring to the processes, characterized mainly by the geometric and dynamic properties of the nuclei, as well as by nuclear density distribution. In particular, ion-ion scattering processes at high ...
The coherent flucton model is applied to the description of some basic nuclear properties, such as: ground state energies, bond energies, nucleon momentum spectra, and nuclear density distributions. It is shown that the momentum distributions of the nucleons coincide with the Fermi distribution for small momenta and exhibit a well pronounced high energy ''tail'', thus providing inclusive reactions of pi-meson generations in kinematically forbidden areas at nucleon-nucleon collisions. Analytical expressions for the bond energy and nuclear density distribution are derived. An agreement with the experimentally obtained data is achieved. The model features are discussed referring to the processes, characterized mainly by the geometric and dynamic properties of the nuclei, as well as by nuclear density distribution. In particular, ion-ion scattering processes at high energy are ...
In 1980 through 1982 a Basewide Energy Systems Plan (BESP) was developed under the direction of the Corps of Engineers at Ft. McClellan to assist the installation in meeting the requirements of the Army Facilities Energy Plan and the ten (10) year Energy Use Reduction Goal. Some of the energy saving projects recommended by the BESP have been implemented. In FY 1977, the total base energy consumption was 1,105,221 MBtu (Million British thermal units). By FY 1987, this had been reduced to 870,900 MBtu, a reduction of twenty-one percent (21%). This resulted in a cost avoidance for FY 1987 over base year FY 1977 of $2,960,986, or a thirty-two percent (32%) reduction.
A first-principles quasiparticle approach to the electronic excitation energies in crystals and at surfaces is described. The quasiparticle energies are calculated within the GW approximation for comparison with photoemission and other spectroscopic experiments. Applications of the method to bulk semiconductors and the Si(111)2[times]l, Ge(111)2[times]l. and H/Si(III) surfaces are presented. In both cases, significant self-energy corrections arising from many-electron effects to the excitation energies are found. Using atomic positions from total energy minimization, the calculated excitation energies explain quantitatively the experimental spectra. This approach thus provides an ab initio means for analyzing and predicting results from spectroscopic probes.
The aim of this work was to study the energy transfer mechanisms from the ligand to the central lanthanide ion of tetracycline-europium (Tc-Eu) complex. The absorption spectra of a EuCl{sub 3}.H{sub 2}O solution was measured and absorption cross-section of Eu{sup 3+} was estimated. The observed overlap predicts a resonant energy transfer from Tetracycline to Eu{sup 3+}. The microscopic parameter of energy transfer was obtained using the overlap integral calculation considering a dipole-dipole energy transfer mechanism and results were compared considering an energy transfer by exchange. In this work, we report also the optical properties of Tc-Eu complex when urea hydrogen peroxide is added to the aqueous solution.
This Energy Savings Opportunity Survey (ESOS) is to identify Energy Conservation Opportunities (ECO`s) which are practical and economical for the reduction of energy consumption in accordance with the Army Facilities Energy Plan. The work to be performed under this project includes: (A) Coordinating with the on-going and proposed related projects. (B) Conducting a limited site survey required to identify applicable ECO`s and obtaining necessary data to evaluate the ECO`s. (C) Evaluating applicable ECO`s to determine their feasibility in accordance with current criteria. (D) Preparing programming and implementation documents for the recommended ECO`s. and (E) Preparing a comprehensive report to present the work performed including energy analysis, the results, and recommendations.
A study to determine how much energy can be recovered from a Florida citrus processing plant was conducted. The production of ethyl alcohol in particular was examined as it is thought to represent the greatest potential for immediate energy recovery. Three-fourths of the energy expended to produce, harvest, process and market a box of fruit was recoverable using existing technology, i.e. 78,500 Btu/ box of fruit recoverable from a total energy expenditure of 107,800 Btu/ box of fruit. Aside from the actual cost benefits of recovering energy in the form of ethanol, the food processor is also helping to reduce the foreign-oil imports by the blending of ethyl alcohol with unleaded gasoline to form gasohol.
The publication presents an outline of the subject of energy management and attempts to test the hypotheses that targeted knowledge management may result in new developments and potentials, and if these are at all desirable. On this basis, a knowledge management system will be developed that may effectively promote developments and potentials in the field of energy management. The tools and fundamentals of energy management are looked into, and the given situation and desired goals are identified by means of an enquiry. This is a scientific study that aims at providing empirical information on the situation and views on the subject of energy management. The analysis, which is supported by an enquiry sheet, is to provide a basis for testing the assumed hypothesis. Further, the potential acceptance and utilization potential of decisive knowledge management in the facility and real estate management sector ...
There are two fundamental reasons or motivations for energy conservation: (1) economics; and (2) consideration of energy - its sources and availability. Economics speaks for itself and needs little explanation: a project is undertaken, the cost is recovered in a given period of time (we hope) and our company realizes cost savings thereafter. We study and propose a project; we estimate the payback. If approved, we implement the project. Then, we eagerly watch for its effectiveness - for the proposed payback. The second consideration in regard to energy conservation might - in the foreseeable future - become by far the most important - that of availability. Very knowledgeable persons have stated that this - in reality - is the most serious problem facing our nation today. Readily available, reasonably priced energy has given to the US the high form of living experienced today. An interruption in this flow ...
The mass asymmetry of fragments from nuclear fission of heavy nuclei is reviewed. While mass asymmetry is a common and well-known phenomenon for low-energy fission of the lighter actinides, more recent experiments have demonstrated that, for the heaviest actinides, the mass distribution switches to a symmetric one. On the other hand, it has been discovered that, though for fissioning nuclei with mass numbers A< or [approx]225 the mass distribution is basically symmetric, an asymmetric component is clearly to be identified for nuclei down to the Pb-region. In the absence of a generally accepted dynamical theory of fission, the above experimental findings are discussed in terms of static energy considerations. Triggered from the outset by the structure of the potential energy surface at the saddlepoint, the energy balance at the scission point between the available energy (Q-value) ...
The mass asymmetry of fragments from nuclear fission of heavy nuclei is reviewed. While mass asymmetry is a common and well-known phenomenon for low-energy fission of the lighter actinides, more recent experiments have demonstrated that, for the heaviest actinides, the mass distribution switches to a symmetric one. On the other hand, it has been discovered that, though for fissioning nuclei with mass numbers A< or #approx#225 the mass distribution is basically symmetric, an asymmetric component is clearly to be identified for nuclei down to the Pb-region. In the absence of a generally accepted dynamical theory of fission, the above experimental findings are discussed in terms of static energy considerations. Triggered from the outset by the structure of the potential energy surface at the saddlepoint, the energy balance at the scission point between the available energy (Q-value) ...
Hydrogen has the potential to serve as both an energy storage means and an energy carrier in renewable energy systems. When renewable energy sources such as solar or wind power are used to produce electrical power, the output can vary depending on weather conditions. By using renewable sources to produce hydrogen, a fuel which can be stored and transported, a reliable and continuously available energy supply with a predictable long-term average output is created. Electrolysis is one method of converting renewable energy into hydrogen fuel. In this experiment we examine the use of an electrolyzer based on polymer-electrolyte membrane technology to separate water into hydrogen and oxygen. The oxygen is vented to the atmosphere and the hydrogen is stored in a small pressure vessel.
Recently it is strongly required to reduce energy consumption to cope with the global warming. Since energy consumption in commercial and residential sectors are increasing while industrial sector is almost constant in Japan, policies to lead energy conservation in urban areas is quite important. This study aims at investigating the performance of urban energy systems which install combined heat and power (CHP) as a district heating and cooling (DHC) plant and the influence of CHP on the structure of electric power systems of utilities. The behavior of energy technologies and the possibility of energy conservation are evaluated based on an optimization model with respect to total system cost. Sensitivity analysis of population allocation into urban areas indicates that fossil fuel consumption varies in the range of 10--20% compared with conventional systems.
Pd/sub 2/Si formation at the Pd-Si interface induced by irradiation with ions having a wide range of nuclear energy of deposition density has been investigated. It is found that the thickness of the silicide layer formed by irradiation is proportional to the ion fluence for irradiation with ions having low energy-deposition densities, while it is proportional to the square root of the fluence for irradiation with ions having energy-deposition densities. The results indicate that Pd/sub 2/Si formation is reaction limited when the energy-deposition density at the interface is low and is diffusion limited when it is high. The results are compared with the phenomenological theory developed by Horino et al. and it is shown that such a dependence of the limiting processes on the energy depositon density is induced when the diffusion is thermally activated while the reaction at the ...
In this study, the authors evaluated how much price changes in food and energy - two basic living expenditures competing for consumers' budgets - would affect consumer welfare. We first estimated a US complete demand system to quantify the interdependent demand relationships among 11 categories of consumption expenditures. Among the estimates, the own price elasticities of both food and energy are relatively inelastic, a finding that explains the dynamics of the recent soaring food and energy prices. The estimated demand elasticities were then incorporated into the measurement of Hicksian compensating variation to analyse the consumer welfare effects of price changes in food and energy. The results indicated that an increase in food and energy prices would increase compensated expenditures...
The LAHET code system calculations and experimental results for proton interactions with an energy <50 MeV are compared. For these energies, the theories behind the LAHET models are not applicable. Three quantities compared are (a) the magnitude of the neutron yield generated through proton interactions, (b) the energy and angular distributions of the resultant neutrons, and (c) the residual nuclei produced by proton interactions (spallation products). The comparisons are for protons incident on iron and copper, except in the case of the energy and angular distributions, which are calculated only for iron. The neutron yields predicted by LAHET agree with published measurements to within 50% for both materials. For iron, the predicted energy and angular distributions agree to within a factor of 3. Finally, the predicted spallation product yields of both materials agree with ...
Within the current outlook for sustainable electric energy supply with concomitant reduction in emission of greenhouse gases, accelerated attention is focusing on the long-term development of hydrogen fuel cell and all-electric battery vehicles to provide alternative fuels to replace petroleum-derived fuels for automotive national fleets. The potential varies significantly between large industrially developed nations and smaller industrially developing nations. The requirement for additional electric energy supply from low-specific energy renewable resources and high-specific energy nuclear resources depends strongly on individual national economic, environmental, and political factors. Analysis of the additional electric energy supply required for the two potential large-scale technologie...
Variations in thermal energy costs of single module solar central receiver systems using one, two, three, and four aperture cavity receivers at a location corresponding to Barstow, California are investigated for nominal power ratings ranging from 100 MWt to 900 MWt. Also considered are the effects on energy costs of changes in plant latitude, and the energy cost impact of the replacement of the single module design with multiple connected modules producing the same thermal power. The results, obtained with the aid of the DELSOL2 computer program, indicate that solar central receiver plant energy costs are insensitive functions of power level, latitude, and configuration. No clear cost of energy advantage between single and multiple modules is seen.
The objective of the present investigation was to develop a Bayesian framework for updating and integrating covariate information into key parameters of metabolizable energy (ME) systems for dairy cows. The study addressed specifically the effects of genetic improvements and feed quality on key parameters in current ME systems. These are net and metabolizable energy for maintenance (NEM and MEM, respectively), efficiency of utilization of ME for milk production (kL) and growth (kG), and efficiency of utilization of body stores for milk production (kT). Data were collated from 38 studies, yielding 701 individual cow observations on milk energy, ME intake, and tissue gain and loss. A function based on a linear relationship between milk energy and ME intake and correcting for tissue energy lo...
This report summarizes the results and activities funded by this three-year award. The principal goal of this project was to determine the thermal conductivity in clusters of galaxies. Intracluster plasmas possess chaotic magnetic fields. Since charged particles are constrained to move primarily along magnetic field lines, the topology of intracluster magnetic fields slows particle diffusion relative to the non-magnetized case, thereby reducing the thermal conductivity. Our first approach to this problem was to employ the static-magnetic-field approximation. In reality, intracluster magnetic field lines are constantly moving, since they are advected by turbulent intracluster motions. The turbulent velocities, however, are much smaller than the rapid speeds of thermal electrons, which make the dominant contribution to the thermal conductivity. In the static-field approximation, one neglects turbulent motions of field lines, and calculates the diffusion coefficient of thermal electrons ...
This publication presents seven national case studies from a coordinated research project on Indicators for Sustainable Energy Development conducted during the 2002-2005 time period. The project was led by the International Atomic Energy Agency (IAEA) in cooperation with the United Nations Department of Economic and Social Affairs (UNDESA). The case studies were developed by research organizations from Brazil, Cuba, Lithuania, Mexico, Russia, Slovakia and Thailand. This publication is being issued just prior to the 15th session of the United Nations Commission on Sustainable Development for which energy for sustainable development is a major theme. The 15th session of the Commission will focus on policy decisions on practical measures and options to expedite implementation in selected clusters of energy issues. The application the energy indicator, especially their quantification, ...
In the convolution/superposition algorithm, the energy spectrum should be modified to make the reconstructed dose distribution consistent with the measured dose distribution. The energy spectrum, which gives the best agreement, is not determined uniquely depending on the reconstruction procedure. In this report, the effects of the characteristics of the energy spectrum on the calculation accuracy are evaluated by comparing the percentage depth dose (PDD) and beam profiles for the reference energy spectrum with those calculated for the modified spectrum in order to optimize the energy spectrum modification procedure when 4 and 10 MV X-ray beams are used. Decreasing the number of energy bins brought a larger decrease rate in the computation accuracy than a decrease rate in computation time. Further, the decrease of the number of energy bins ...
Government facilities and services are often the largest energy users and major purchasers of energy-using equipment within a country. In developing as well as industrial countries, government ''leadership by example'' can be a powerful force to shift the market toward energy efficiency, complementing other elements of a national energy efficiency strategy. Benefits from more efficient energy management in government facilities and operations include lower government energy bills, reduced greenhouse gas emissions, less demand on electric utility systems, and in many cases reduced dependence on imported oil. Even more significantly, the government sector's buying power and example to others can generate broader demand for energy-efficient products and services, creating entry markets for domestic ...
A link is made in this paper between proposed low energy scenarios for different Western European countries and the amount of pollutants that may result from these scenarios. Air pollutant emissions are calculated for the ten countries for which low energy scenarios are available. These scenarios emphasize stringent energy efficiency, maximizing the use of renewable (other than nuclear) energy, and minimizing the use of fossil fuels. Under these low energy scenarios, the average per capita energy use (year 2030) in the ten countries is estimated as 97 GJ/person, which is a decrease of 38% relative to 1980. Using the energy consumption figures from the low energy scenarios, together with sector- and fuel-specific emission factors from Europe, the resulting emissions of SO_2 , NO_x , and CO_2 were computed. These estimates ...
Energy balances are analysed from a life-cycle perspective for biogas systems based on 8 different raw materials. The analysis is based on published data and relates to Swedish conditions. The results show that the energy input into biogas systems (i.e. large-scale biogas plants) overall corresponds to 20-40% (on average approximately 30%) of the energy content in the biogas produced. The net energy output turns negative when transport distances exceed approximately 200 km (manure), or up to 700 km (slaughterhouse waste). Large variations exist in energy efficiency among the biogas systems studied. These variations depend both on the properties of the raw materials studied and on the system design and allocation methods chosen. The net energy output from biogas systems based on raw materials that have high water content and low biogas yield (e.g. manure) is ...
This paper discussed issues related to the storage of electricity produced from renewable energy sources. Storage systems currently used by distribution systems were reviewed. The study showed that successful storage systems ensure high charging and discharging rates for shorter periods of time. Systems with high storage capacities must also be able to store energy for longer periods of time than traditional energy storage systems. Systems include pumped storage plants; electro-chemical accumulators; compressed air accumulators; and redox flow batteries. Hydrogen technologies for the storage of electric energy from renewable sources were reviewed. The paper also outlined energy storage and fuel cell research currently being conducted by researchers in the Czech Republic. The study concluded by stating that new energy storage technologies are required to ensure ...
The Energy Information Administration (EIA) prepares quarterly, short-term energy supply, demand, and price projections for publication in February, May, August, and November in the Short-Term Energy Outlook (Outlook). An annual supplement analyzes the performance of previous forecasts, compares recent cases with those of other forecasting services, and discusses current topics related to the short-term energy markets. (See Short-Term Energy Outlook Annual Supplement, DOE/EIA-0202.) The forecast period for this issue of the Outlook extends from the third quarter of 1993 through the fourth quarter of 1994. Values for the second quarter of 1993, however, are preliminary EIA estimates (for example, some monthly values for petroleum supply and disposition are derived in part from weekly data reported in the Weekly Petroleum Status Report) or are calculated from model simulations using ...
This report of an interview with T. Watamori, Chairman of the Board of Directors of the New Energy Development Organization (NEDO), Japan outlines the general activities of NEDO, and then gives emphasis to the prospects of the liquefaction of brown coal from Australia. (In Japanese)
The proceedings include the following lectures: Facing the challenges - new structures for electricity production. Renewable energies in Europe - chances and challenges. Nuclear outlook in the UK. Sustainable energy for Europe. Requirements of the market and the grid operator at the electricity production companies. Perspectives for the future energy production. Pumped storage plants - status and perspectives. Nuclear power/renewable energies -partners or opponents? New fossil fired power stations in Europe - status and perspectives. Nuclear energy: outlook for new build and lifetime extension in Europe. Biomass in the future European energy market - experiences for dong energy. Meeting the EU 20:20 renewable energy targets: the offshore challenges. DESERTEC: sustainable electricity for Europe, Middle East and North ...
Combined energy plants operating on the Brayton-Rankine cycle have gained wide acceptance as the most efficient energy conversion system. The technology is well proven and numerous research activities are underway to develop it further past its present plateau of performance. In developed and emerging economies alike, the current situation in the global economic market has caused the liberalisation of the energy industry in some countries, and in others it is causing a rethink of economic and energy policies. A result is that electric utility companies that have enjoyed a monopoly in power generation and distribution are seeing this privilege being eroded. This is opening up opportunities for independent power production and, consequently, for gas/steam turbine plants because of the technical merits of the technology and its ability to fill the vacuum being created in the energy ...
An experimental evaluation of the Fano factor F in silicon at hard X-ray energies (5.9-136.5 keV) has been performed by means of a low-noise, high charge collection efficiency silicon drift detector with on-chip electronics. A dependence of F from the detector temperature as well as from the energy of the X-ray photons has been found. Assuming a pair creation energy equal to 3.64 eV, at +20 deg. C the F factor was observed to vary from 0.124{+-}0.006 at 5.9 keV up to 0.159{+-}0.002 at 122 keV. At -35 deg. C, the change of F with respect to the photon energy was less remarkable but nevertheless statistically significant, from 0.123{+-}0.002 at 5.9 keV up to 0.134{+-}0.001 at 122 keV. To our knowledge, the present results represent the first experimental evidence of an energy dependence of the Fano factor in silicon at hard X-ray energies.
Neutron Star Evolution with Internal Energy h'q/>a. Dissipation by Vortex Creep. N. Shibazaki and F. K. Lamb. University of Illinois at Urbana-Champaign ...
Jul 16, 2005 ... The purpose of this capability portfolio is to develop a roadmap for NASA to exploit .... 1.2.4-2: Some applications of nanotechnology to advanced EVA suits. ..... Power/Energy Storage: Materials and devices for energy storage and .... to 80 %), manufacturing costs (up to 50%) and enhancements in durability. ...
Few studies have examined energy metabolism during prolonged, strenuous exercise. We wanted therefore to investigate energy metabolic consequences of a prolonged period of continuous strenuous work...Full Text Available
The author demonstrates through a specific example that it is possible to extract rotational energy from a Kerr source (in principle, of arbitrary size but not turned black) through a reversible process by suitably injecting tachyons. (Auth.).
Provides standardized energy balance sheets expressed in a common unit of tons of oil equivalent for all OECD countries as well as the regions: OECD total, IEA, North America, Pacific, OECD Europe, EEC and Yugoslavia.
The 7 conference papers in Vol. 9 review the implications of environmental problems and discuss the consequences of pollution abatement measures, especially for the economics of energy conversion. The future developments of pollutant emissions are assessed.
A pedagogical introduction to the equivalence theorem for longitudinal vector bosons in electroweak theories is given and the problem of tree-level unitarity at high energies in models of electroweak interactions is briefly reviewed. To make the treatment self-containded, the basic of the Standard Model are summarized in an appendix.
The unique challenges and opportunities associated with China's rapid economic growth were discussed with reference to the potential risk of political disruption or destabilizing international markets. The author notes that two common mistakes are typically made when assessing the evolution of China's energy policy. The first is that China's future path is assimilated with that of developed countries, thereby dismissing evidence that might point toward a different relationship with energy. Second, analysts tend to focus on the external expression of China's energy needs, its oil imports, while overlooking other energy-related issues such as insufficient electricity supplies or environmental degradation. The author argues that Chinese leadership is redefining its understanding of what constitutes energy security for the country. This report assesses the international impacts of such ...
Study of the conversion of chicken litter to biogas for the production of energy. There was an additional requirement that after extracting the energy from the chicken litter the nutrient value of the raw chicken litter had to be returned to the Ak-Chin Farms for use as fertilizer in a form and delivery method acceptable to the Farm.