Energy Technology Data Exchange (ETDEWEB)

The half-metallic Heusler alloy Ni{sub 2}MnIn is of high interest for use in spin electronics since at the Ni{sub 2}MnIn/InAs interface a spin polarization of 100% is predicted. We prepare high-quality thin films of 20-60nm thickness by co-evaporation and DC magnetron sputtering. Point-contact Andreev reflection spectroscopy yields a spin polarization of up to 54%. By spectral generalized magneto-optical ellipsometry, the dielectric and magneto-optical properties are determined and ferromagnetic behavior below the Curie temperature T{sub C}=318K is proved.

Energy Technology Data Exchange (ETDEWEB)

The properties of Mn-doped GaAs layers grown by laser deposition were investigated with measurements of Hall effect and magneto-optical Kerr effect (MOKE). The electrical and magnetic parameters of the layers were defined by growth temperature and quantity of sputtered Mn. It was shown that room-temperature ferromagnetism is revealed by MOKE and, after ruby laser 25 ns pulse annealing, by Hall effect measurements.

International Nuclear Information System (INIS)

Short communication.

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

Not Available

British Library Electronic Table of Contents (United Kingdom)

The effects of thermal radiation and viscous dissipation on magneto-hydrodynamic (MHD) unsteady free-convection flow over a semi-infinite vertical porous plate are analysed. The fluid considered is non-gray (absorption coefficient dependent on wave length). The Network Simulation Method is used to solve the boundary-layer equations based on the finite-difference formulation; only discretization of the spatial co-ordinates is necessary, while time remains as a real continuous variable. This method provides a solution for both transient and steady-state problems at the same time, and programming does not require manipulation of the sophisticated mathematical software that is inherent in other numerical methods. The velocity, temperature, local skin-friction and local Nusselt number are studi...

British Library Electronic Table of Contents (United Kingdom)

This paper presents a new algorithm which is applicable in designing a smart damping system for vibration mitigation. The algorithm, which is extended into a unified system from Lyapunov stability theory, enables us to decrease the errors by its increased stability. The validity of this design method was proved in the experiment on a control model of three-storied building structure. Smart damper was used for MR (Magneto-Rheological fluid) damper in the experiment, and its control effectiveness was evaluated. In order to make a more accurate control model mathematically, we updated the model on the basis of the analysis of dynamic characteristics of structure and of the mathematical analysis of a lumped mass model, and then employed a state space model redefined by structural property matr...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

CERN Document Server

Here we show that self-propulsion in quantum vacuum may be achieved by rotating or aggregating magneto-electric nano-particles. The back-action follows from changes in momentum of electro-magnetic zero-point fluctuations, generated in magneto-electric materials. This effect may provide new tools for investigation of the quantum nature of our world. It might also serve in the future as a "quantum wheel" to correct satellite orientation in space.

Science.gov (United States)

The influence of ablation on stagnation region convective heating for ... and thermal properties of this fiber depend on the fluorination process ... However, these properties are between those of graphite and those of PTFE (Teflon). ...

International Nuclear Information System (INIS)

Scanning thermal microscopy (SThM) was used to map thermal conductivity images in an ultrafine-grained copper surface layer produced by surface mechanical attrition treatment (SMAT). It is found that the deformed surface layer shows different thermal conductivities that strongly depend on the grain size of the microstructure: the thermal conductivity of the nanostructured surface layer decreases obviously when compared with that of the coarse-grained matrix of the sample. The role of the grain boundaries in thermal conduction is analyzed in correlation with the heat conduction mechanism in pure metal. A theoretical approach, based on this investigation, was used to calculate the heat flow from the probe tip to the sample and then estimate the thermal conductivities at different scanning positions. Experimental results and theoretical calculation demonstrate that ...

International Nuclear Information System (INIS)

The electrically heated rod is usually used as a substitute for fuel rod in thermal-hydraulic experiment. However, the different structure and thermal properties between nuclear fuel rod and electrically heated rod result in different steady-state distribution of temperature and stored energy and different response to thermal-hydraulic in simulation transient experiment. This paper analyses the effect of structure and thermal properties differences between nuclear fuel rod and electrically heated rod on experiment, and then introduce a feasible method, i.e. electric power is controlled by a program, to reduce the differences between the transient responses of nuclear fuel rod and electrically heated rod. At the same time, this paper points out the limits of the method. (authors)

Science.gov (United States)

This paper presents a theoretical study of heat transfer from magneto-rheological fluid (MRF) dampers. A lumped system model is developed which is capable of predicting the temperature rise for any size MRF damper. As a case study example, finned and unfinned dampers are compared for automotive-size MRF dampers. The results demonstrate that heat transfer from these devices can be enhanced considerably with the use of fins.

British Library Electronic Table of Contents (United Kingdom)

Commercial polyolefin, such as poly(propylene), are widely used because of their easy processing and their excellent mechanical and thermal properties. Although their recycling is well established, the mechanical and thermal properties of the recycled waste poly(propylene)(WPP) are normally lower than those of the virgin material. The introduction of talc can improve the toughness, without compromising the processability and recycling capabilities. However, the thermal properties of these blends should be assessed to limit degradation during recycling. The effect of gamma radiation on the thermal and mechanical properties of WPP/High Crystallinity Poly(propylene)/Talc was studied. TGA, DSC, and electrical conductivity performed the characterization of WPP composites. Mechanical properties ...

UK PubMed Central (United Kingdom)

Thermal behaviors of eucalyptus wood residue (EWR) filled recycled high density polyethylene (HDPE) composites have been measured applying the thermogravimetric analysis (TGA) and differential scanning...Full Text Available

International Nuclear Information System (INIS)

This paper presents the effect of precursor powder size on the thermoelectric properties of sintered nanostructured bulk materials. The transport properties of the nanostructured bulk show a dramatic size effect. There are a lower thermal and electrical conductivity for the bulk with smaller nanopowders. The dimensionless figure-of merit values (ZT) of almost all the samples are much lower than those of the list reported data in the paper because the decrease in the thermal conductivity is counteracted by the reduction in the electrical conductivity and the Seebeck coefficient. The combination route of hydro/solvothermal synthesis and spark-plasma-sintering method provide a well controlled way to significantly reduce the thermal conductivity.

Science.gov (United States)

Graphitized thermal carbon black has also been reported by Kalaschinikova et al. (11) to have excellent adsorption properties for CI-C6 alkanes, ...

Energy Technology Data Exchange (ETDEWEB)

Explosives molecules have a number of unique properties. These properties are discussed. They include low vapor pressures, electronegativity, ''stickiness,'' frangibility, and thermal instability. The program for developing an advanced explosives detector is described.

Science.gov (United States)

Lecture notes (pdf) on Ceramics is part of a physics course on the properties of matter from the University of Auckland, Department of Chemical and Materials Engineering. The following topics are covered: types of chemical bonding, degree of ionic character, structure of ceramics and crystallography, interstitial sites in different crystal structures, silicate structures, glasses, glass transition temperature, glass viscosity, thermal and mechanical properties of ceramics and glasses, fracture properties of ceramics and processing of ceramic materials. Keywords: ionic bonds; covalent bonds; coordination numbers; thermal shock; grain growth; sintering; green body

Energy Technology Data Exchange (ETDEWEB)

This definitive reference is organized in an easy-to-follow format based on materials properties. It features new and existing data verified through major professional societies in the materials fields, such as ASM International and the American Ceramic Society. The third edition has been significantly expanded, most notably by the addition of new tabular material for a wide range of nonferrous alloys and various materials. The contents include: Structure of materials; Composition of materials; Phase diagram sources; Thermodynamic and kinetic data; Thermal properties of materials; Mechanical properties of materials; Electrical properties of materials; Optical properties of materials; Chemical properties of materials.

Energy Technology Data Exchange (ETDEWEB)

The paper reports on the results of a study of the synthesis conditions effects on magnetic and transport properties of nanosized layers of high-T{sub c} diluted magnetic semiconductors (DMS), such as Ge:Mn, Si:Mn and Si:Fe, fabricated by laser-plasma deposition over a wide range of the growth temperature, T{sub g}=(20-550) deg. C on single-crystal GaAs or Al{sub 2}O{sub 3} substrates. Ferromagnetism of the layers was detected by measurement data of the magneto-optical Kerr effect, anomalous Hall effect, negative magnetoresistance and ferromagnetic resonance (FMR) at 5-500 K. The optimum growth temperature, T{sub g}, for Si:Mn/GaAs layers with T{sub c}{approx}400 K is shown to be about 400 deg. C. The Si:Mn/Al{sub 2}O{sub 3} layers with 35% of Mn have the metal-type of conductivity with manifestation of magnetization up to room temperature. Different types of uniformly doped structures and digital alloys have been investigated. In contrast to ...

Energy Technology Data Exchange (ETDEWEB)

Calculations of refrigerant thermal properties are desired to be very fast and stable in cases of simulation of refrigeration system, etc. The traditional method based on equation of state cannot meet such requirement because of unavoidable iterations in calculation. In this paper, a new calculation method for refrigerant thermal properties is presented. Low order implicit polynomial equations are got by using curve-fitting method at first, and then explicit formulae for calculating refrigerant thermal properties quickly are obtained by getting the analytical solution of these implicit equations. Explicit fast calculation formulae for thermal properties of R22 and R407C, covering the saturated temperature of -60{approx}80 {sup o}C and superheat of 0-65 {sup o}C, are presented as examples. The calculation speeds of the ...

British Library Electronic Table of Contents (United Kingdom)

Abstract This study was undertaken over a 10-month period under environmental conditions within the state of Mato Grosso, Brazil, to evaluate the causes of variation in the technological and thermal properties of raw natural rubber (NR) from different clones of Hevea brasiliensis (GT 1, PR 255, FX 3864, and RRIM 600). These clones were chosen to represent good clones available in Brazil. The technological properties of raw NR were evaluated in terms of their dry rubber content (DRC), Wallace plasticity, plasticity retention index (PRI), and Mooney viscosity. The thermal performance was evaluated with the thermogravimetry (TG)/differential thermogravimetry (DTG) technique. There were significant variations (p < 0.01 and p < 0.05) between clones and tappings for all technological properties,...

Energy Technology Data Exchange (ETDEWEB)

Magneto-striction and magnetic form factors in 5f itinerant antiferromagnets UNiGa{sub 5} and UPtGa{sub 5} are studied by means of neutron scattering. Remarkable magneto-striction was observed around T{sub N}, indicating large spin-orbit coupling in the itinerant system. The orbital magnetic moment is found to be strongly suppressed due to the hybridization of uranium 5f with Ga-4p electron.

Science.gov (United States)

This study presents a theoretical analysis of heat generation and dissipation of field-controllable magneto-rheological fluid (MRF) shock absorbers. Since MRF dampers are energy- dissipating devices, the issues of heat generation and dissipation are important in predicting their performance. A theoretical model is developed based on Bingham plastic model to estimate temperature history of the MRF dampers. The governing equation includes the MRF viscosity as a function of the temperature. The numerical solutions are compared with experimental results in order to validate the accuracy of the model, and excellent agreements are obtained.

British Library Electronic Table of Contents (United Kingdom)

A three-dimensional numerical study is performed to explore the effect of pulsed spanwise-periodic surface thermal perturbation (also denoted as thermal bump) in a Mach 1.5 flat plate laminar boundary layer. A high-resolution upwind-biased Roe method is used with the compressive Van Leer harmonic limiter on a suitably refined mesh. The dependence of flow stability characteristics on the variation of thermal bump geometry (shape and dimension) and pulsing properties (disturbance amplitude and frequency) is assessed. It is shown that the finite-span thermal bumps generate streamwise vortices. When the thermal bump is pulsed, vortex shedding is observed, and the streamwise vorticity grows with the downstream distance. Analysis of the integrated disturbance energy indicates that the streamwise...

Science.gov (United States)

The Swedish Ceramic Institute is an industrial research institute working with product-oriented research and development of ceramics and closely related materials. The institute works with the processing and fabrication of ceramic materials as well as with materials properties and design questions. Its website provides details of research projects (engineering ceramics, electroceramics, traditional ceramics). Publications are listed, with some downloadable files (annual reports, research reports, information leaflets). Sample materials data (mechanical properties, thermal properties) is given for oxides and non-oxide ceramics.

Energy Technology Data Exchange (ETDEWEB)

The exposure of heat-resistant alloys to high temperature can significantly change their mechanical properties. This paper presents and analyzes data on the effect of thermal exposure on the tensile and impact behavior of three cast materials -- the HK-40, HP-50, and 21Cr-32Ni-Fe alloys -- and of wrought material -- Alloy 800. The changes in tensile and impact properties caused by high-temperature exposure are reviewed. Reasons for these property changes and needs for considering them in the design, operation, and life assessment of high-temperature equipment are discussed.

Energy Technology Data Exchange (ETDEWEB)

A one-dimensional thermal model is derived to describe the temperature field around a vertical borehole heat exchanger (BHEX) for a geothermal heat pump. The inlet and outlet pipe flows are modeled as one, and an effective heat capacity is added to model the heat storage in the fluid and pipes. Parameter estimation techniques are then used to estimate various parameters associated with the model, including the thermal conductivity of the soil and the grout that fills the borehole and surrounds the U-tube. The model is validated using test data from an experimental rig containing sand with known thermal conductivity. The estimates of the sand's thermal conductivity derived from the model are found to be in good agreement with independent measurements.

International Nuclear Information System (INIS)

Control of thermal expansion is often necessary in the design and selection of electronic packages. In some instances, it is desirable to have a coefficient of thermal expansion intermediate between values readily attainable with single or two phase materials. The addition of a third phase in the form of fillers, whiskers, or fibers can be used to attain intermediate expansions. To help design the thermal expansion of multiphase materials for specific applications, a closed form model has been developed that accurately predicts the effective elastic properties of isotropic filled materials and transversely isotropic lamina. Properties of filled matrix materials are used as inputs to the lamina model to obtain the composite elastic properties as a function of the volume fraction of each phase. Hybrid composites with two or more fiber types are easily handled with ...

UK PubMed Central (United Kingdom)

Animals sense changes in ambient temperature irrespective of whether core body temperature is internally maintained (homeotherms) or subject to environmental variation (poikilotherms). Here we show...Full Text Available

International Nuclear Information System (INIS)

The thermal properties of five types of radiation-induced wood-polymer composites based on a tropical hardwood, rubberwood (Hevea braziliensis), was studied by oxygen index measurement, differential thermal analysis (DTA) and thermogravimetry (TG). The DTA and TG curves of composites were different from those of rubberwood, which can be attributed to the presence of the incorporated polymers. Of the five composites, the one impregnated with bis(2-chloroethyl)vinyl phosphonate reduced the initial temperature of decomposition, increased the peak temperatures of exothermic reactions, and increased the char yield. Comparison with physical blends of rubberwood and the corresponding polymer provided some evidence of chemical interaction of wood and polymer in some of the composites. (author).

International Nuclear Information System (INIS)

The influence of heat treatment on the structure, mechanical properties and fracture peculiarities of high-strength (#alpha#+#beta#)-titanium alloy VT22 has been studied. It is ascertained that thermal cycling and subsequent high-temperature aging permit to reduce considerably crack growth rate. Thermal cycling is realized in the following mode: heating in #beta#-region, cooling and allowance in (#alpha#+#beta#)-region, heating in #beta#-region.

Energy Technology Data Exchange (ETDEWEB)

The enhancement of longitudinal heat transfer by means of fluid pulsation in a pipe has been investigated analytically and numerically, including the transient state. The effects of pulsation amplitude, frequency, and pipe length on thermal properties such as effective thermal diffusivity and delay time are clarified. Their effects on numerical calculations are also presented and suggestions for efficient numerical calculations of this problem are made concerning the combination of parameters.

Science.gov (United States)

Henry constants for the adsorption of o- and p-phenylenediamines on the surface of graphitized thermal carbon black within the temperature range 433-479 K were calculated by the molecular statistical method. The parameters of the atom-atom potential function of intermolecular interaction between the nitrogen atom in aniline and isomeric phenylenediamines and the carbon atom of the basal face of graphite were determined. It was shown that an intramolecular H bond influenced the geometry and adsorption properties of o-phenylenediamine.

British Library Electronic Table of Contents (United Kingdom)

In vibration control field, magneto-rheological (MR) fluid dampers are semi-active control devices that have recently begun to receive more attention. This paper presents a nonlinear black-box model (BBM) and an inverse black-box model (IBBM) for the identification of a MR fluid damper and their application to design a novel force-sensorless control method for any damping system using that damper. The nonlinear model named 'black-box' is a simple direct modeling method which was designed based on fuzzy-neural technique. Characteristics of the damper in study are directly estimated through a fuzzy mapping system. In order to improve the model accuracy, neural network technique including back-propagation and gradient descent method were used to train the fuzzy parameters to minimize the mode...

British Library Electronic Table of Contents (United Kingdom)

In vibration control field, magneto-rheological (MR) fluid dampers are semi-active control devices that have recently begun to receive more attention. This paper presents a black-box model (BBM) for identification of a MR fluid damper and its application to vibrating control systems using that damper with self-sensing behavior. A model named ''black-box'' is a simple direct modeling method which is designed for a typical MR fluid damper using the self-tuning fuzzy technique. The characteristics of the researched damper are directly estimated through a fuzzy mapping system. In order to improve the accuracy of the proposed model, the back propagation algorithm and gradient descent method were used to train the fuzzy parameters to minimize the model error function. Consequently, the BBM with ...

International Nuclear Information System (INIS)

The influence of structure on mechanical properties in the course of tensile tests in a wide range of temperatures was studied, using the VT16 structure thermally strengthened (alpha+beta)-titanium alloy by way of example. It is ascertained that transition from ductile to brittle fracture at the temperature of -196 deg C is observed only in coarse-grain alloy having alpha-eldging of beta grains.

International Nuclear Information System (INIS)

Polymer composites are used in numerous applications. In spite of this fact, new developments are still under way to explore in other field of application of these materials and to tailor their properties for more extreme condition. A particular emphasis is focused on fillers content is summarized. Some steps towards the functionally graded materials are illustrated. The FT-IR spectroscopic studies revealed the information about curing of epoxy with fillers. It was observed that mechanical properties like tensile strength, hardness etc get enhanced up with filler contents. The effect of the different formulations were investigated and discussed for optimum process condition. (author)

Science.gov (United States)

Resistance exercise has been widely reported to have positive rehabilitation effects for patients with neuromuscular and orthopaedic conditions. This paper presents an optimal design of magneto-rheological fluid dampers for variable resistance exercise devices. Adaptive controls for regulating the resistive force or torque of the device as well as the joint motion are presented. The device provides both isometric and isokinetic strength training for various human joints.

International Nuclear Information System (INIS)

We have performed precision measurements in a magneto-optical trap of the 7P1/2 hyperfine structure of the isotopes 209-210Fr. The ratio of these hyperfine constants to the previously measured 7S1/2 ground state values reveals a significant hyperfine anomaly. This anomaly results from the different radial dependence of the electron density in the two atomic levels. The measurements are sensitive to changes in the radial distribution of the neutron magnetism.

Energy Technology Data Exchange (ETDEWEB)

A series of experiments were carried out to examine the resistant capacity of a chemically treated hard wood, Anthocephalus cadamba (Roxb) Miq. to thermal and termite degradation. The treatment with thermosetting resins viz. urea formaldehyde (UF), melamine formaldehyde (MF) and phenol formaldehyde (PF) at 31-33 levels of weight percent gain (WPG) increased the strength property i.e. modulus of rupture (MOR) by 7.50-21.02% and stiffness i.e. modulus of elasticity (MOE) by 9.50-12.18% over the untreated one with no remarkable effect on specific gravity. The treated samples were found resistant to termite attack, while the untreated one was badly damaged by termites on 12 months' exposure to a termite colony. The thermal degradations of untreated and treated wood samples were studied using thermogravimetric (TGA) and differential thermogravimetric (DTG) techniques at heating rates 20 and 30 {sup o}Cmin{sup -1} in ...

Energy Technology Data Exchange (ETDEWEB)

Transition joints in power plants between ferritic steels and austenitic stainless steels suffer from a mismatch in coefficients of thermal expansion (CTE) and the migration of carbon during service from the ferritic to the austenitic steel. To overcome these, nickel-based consumables are commonly used. The use of a trimetallic combination with an insert piece of intermediate CTE provides for a more effective lowering of thermal stresses. The current work envisages a trimetallic joint involving modified 9Cr-1Mo steel and 316LN austenitic stainless steel as the base materials and Alloy 800 as the intermediate piece. Of the two joints involved, this paper describes the choice of welding consumables for the joint between Alloy 800 and 316LN. Four consumables were examined: 316, 16-8-2, Inconel 82 and Inconel 182. The comparative evaluation was based on hot cracking tests and estimation of mechanical properties and coefficient ...

Energy Technology Data Exchange (ETDEWEB)

The iron smelting performance of brown coal coke is compared to black coal coke in a small experimental cupola furnace with 300 mm internal diameter. Relations between major operational parameters are explained, including coke properties, coke lump size, cupola furnace geometry, air supply and temperature conditions. Thermal efficiency of the furnace, a thermal balance (Sankey diagram) as well as results of 12 smelting tests are described. Smelting results were used to establish a coke assessment diagram with minimum limit lines for coke properties required for satisfactory cupola smelting. The influence of furnace dimensions, horizontal and vertical, is further analyzed in order to derive conclusions on coke suitability for larger industrial cupola furnaces. The performance of brown coal coke types was below the limit of technological quality, all other coke types above the minimum quality level are ...

Energy Technology Data Exchange (ETDEWEB)

The major part of the chapter 'Physical Properties' in concerned with, in addition to nuclear and atomic properties, the properties of the metal molybdenum. Due to the huge number of relevant papers, the present volume comprises only the first part of the metal properties, i.e. the crystallographic properties, the electronic structure, the lattice dynamics, and subsequently the mechanical and thermal properties. There are two small sections where the properties of the molecules, primarily Mo/sub 2/ and Mo/sub 6/, and of the vapor are described. The strength and some other mechanical properties have been frequently investigated to establish the change due to neutron irradiation, because this affects the durability of the fuel containers in nuclear reactors. For that purpose, changes ...

Science.gov (United States)

Constant property, laminar flow heat transfer in a semicircular tube with uniform wall temperature has been analyzed to define the lower bound of heat transfer augmentation in circular tubes with twisted-tape inserts. Two thermal boundary conditions, which correspond to the two extremes of the fin effect of twisted tapes encountered in practical applications, are considered. Numerical solutions, employing finite-difference formulations for the governing momentum and energy equations were carried out for the thermal entrance region and for fully developed flow.

British Library Electronic Table of Contents (United Kingdom)

Abstract Thermomechanical behavior of membranes based on blends of poly(vinyl alcohol) (PVA) with different weight percentage (wt %) of glycerol has been studied. Solid-state PVA/Glycerol polymer membranes were prepared by a solution casting method. The films were studied for thermal characteristics by differential scanning calorimetry (DSC) and thermogravimetric analysis and for the mechanical properties including hardness and modulus by nanoindentation method. The dispersion of glycerol within the polymer matrix was examined using scanning electron microscopy. Fourier transform infrared spectroscopy was used to confirm the formation of hydrogen bonding between the plasticizer and PVA in their blends and also to provide information on compatibility and physical interactions between the gl...

Energy Technology Data Exchange (ETDEWEB)

A compression ignition engine was operated on dual fuel principle inducting two commercial fuels and four pure hydrocarbon fuels in turn through intake manifold along with air and injecting diesel fuel to initiate the combustion in the conventional manner. The engine was operated at different loads and at each load the quantity of inducted fuel was increased gradually till knocking set in. The engine performance and exhaust pollutant emissions were recorded at different operating conditions. It was observed that the extent of induction and the effect on the performance depend on the properties of the inducted fuel such as volatility, self ignition temperature and oxidation characteristics. The energy release during the cycle was also observed to shift depending on the properties of inducted fuel. With the dual fuel operation, the thermal efficiency at part loads was observed to be less compared to neat diesel operation. The ...

International Nuclear Information System (INIS)

The effect of both dopant and neutron radiation on the optical and thermal properties of polyvinyl chloride (PVC) has been studied. The doped samples with Pb and Cd were irradiated with a 14 MeV-neutron fluence in the range 7-28.8 x 10"9 n/cm"2. The optical energy gap E_o_p exhibits a significant dependence on the type of additive and the neutron irradiation fluence. The specific heat at constant pressure C_p showed a nonmonotonical change with radiation fluence. The results of this study show that PVC:Pb behaves as a crystalline structure which is only slightly affected by neutron irradiation, while PVC:Cd is highly affected. (author).

British Library Electronic Table of Contents (United Kingdom)

In the present paper, the effects of hydroxyapatite (HA) content on the microstructure, thermal and mechanical properties of Ti-based glassy alloy/HA composite prepared by spark plasma sintering (SPS) are investigated. The microstructure of the composites is homogeneous when the HA is lower than 2 wt%. When the HA content is higher than 3 wt%, the crystalline precipitates with size of less than 5 nm are distributed in the glassy matrix. HA decomposes during sintering procedure for the composite with high HA content. With increasing HA addition, compressive strength decreases. Especially for the HA content is over 2 wt%, the strength decreases sharply because of partial crystallization of glassy alloy matrix.

International Nuclear Information System (INIS)

Composite nitrides (such as BN, TiN) are widely used in various industrial applications because of their extreme wear and corrosion resistance, thermal and electrical properties. in order to obtain composite materials with these optimal properties, it is important to elucidate whether any chemical reactions occur at nitride/metal interfaces, e.g., those involving BN-Ti/TiN. Materials of interest include the deposition by PVD of Ti and TiN on BN substrates. Some of these systems were then subjected to varying degrees of physical and thermal alteration. Detailed X-ray photoelectron spectroscopy (XPS) has therefore been rendered of these interfaces using cross-sectional display and sputter etching. Resulting structural and morphological features have been investigated with transmission electron microscopy (TEM) and X-ray diffraction (XRD). Diffusion of the nitridation, oxynitride formation and interfacial ...

Energy Technology Data Exchange (ETDEWEB)

A solar thermophotovoltaic (STPV) system has both terrestrial and space applications because thermal energy storage can be utilized. Excellent properties (heat of fusion=1800 j/gm and melting temperature=1680 K) make silicon the ideal thermal storage material for an STPV system. Using a one dimensional model with tapering of the silicon storage material, it was found that several hours of running time with modest lengths ({approximately}15 cm) of silicon are possible. Calculated steady-state efficiencies for an STPV system using an Er-YAG selective emitter and ideal photovoltaic (PV) cell model are in the range of 15{percent}{endash}17{percent}. Increasing the taper of the storage material improves both efficiency and power output. {copyright} {ital 1996 American Institute of Physics.}

British Library Electronic Table of Contents (United Kingdom)

This study aimed to enhance the dimensional stability of flat-pressed wood plastic composites (WPCs) containing fast growing wood fibres by a thermal-treatment method. The wood fibres were treated at three different temperatures (120, 150, or 180 degreeC) for 20 or 40 min in a laboratory autoclave. The WPC panels were made from dry-blended Eucalyptus camaldulensis wood fibres and polypropylene (PP) powder (50:50 by weight) using a conventional flat-press process under laboratory conditions. Thickness swelling and water absorption of the WPC panels significantly decreased with increasing the treatment temperature and time. The thermal-treatment of eucalyptus wood fibres slightly decreased the screw withdrawal resistance of the WPC panels as compared to the reference panels while the flexura...

Energy Technology Data Exchange (ETDEWEB)

In most industrial processes operating at elevated temperatures, protective oxide layers perform a vital duty in protecting the underlying metallic alloys from process gases. Coal-fired combined cycle power generation systems present a number of process conditions in which the properties of the protective oxide layers are particularly important. This paper discusses two of these particular conditions: (1) `erosion/corrosion` of in-bed heat exchanger tubing and (2) thermal cycling of hot gas path components. For both these situations, the desirable properties of protective scales are outlined. The behaviour of scales in practice are highlighted. 33 refs., 6 figs., 2 tabs.

Energy Technology Data Exchange (ETDEWEB)

The bibliography contains citations concerning the properties, industrial uses and federal regulation of asbestos. The references explore advantages and disadvantages associated with use of industrial robots in areas containing high concentrations of asbestos dust, the use of water as a cutting tool to control the generation of asbestos dust, and governmental policies and attitudes relative to the health and welfare of workers subjected to asbestos. Thermal insulation properties, wear characteristics, high temperature capabilities, use as a reinforcement in composite materials, and asbestos substitutes are included. (Contains a minimum of 69 citations and includes a subject term index and title list.)

International Nuclear Information System (INIS)

The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.

Energy Technology Data Exchange (ETDEWEB)

Vacuum insulation panels (VIP) offer excellent thermal resistance properties that can enhance the energy efficiency of insulating systems, save space and contribute to energy consumption reductions. However, VIPs are not used much in Canada, and new commitments to carbon dioxide reductions has created the need to study the prospect of using VIPs in various components of a building envelope. For that reason, assessment methods for the applicability and sustainability of VIPs for use in building envelope construction were developed. There are practical aspects regarding the long-term performance and application of VIPs in building construction. Air molecules and water molecules can permeate through the foil and seams of the VIPs, causing a reduction in thermal resistance. This paper addresses some of the test methods that may accelerate long term changes in thermal resistance. Results were presented from ...

Energy Technology Data Exchange (ETDEWEB)

One requirement of a thermophotovoltaic (TPV) radiator is to efficiently emit photons at high temperatures to TPV cells for conversion to electric power. Because many candidate radiator materials with adequate structural properties display low emissivity, coatings or other surface modifications are required for enhancement of emissivity. Six plasma sprayed coatings and one textured surface demonstrated adequate thermal stability and emittance values of 0.8 or greater. Promising attributes of modified surfaces are identified.

Energy Technology Data Exchange (ETDEWEB)

The paper industry needs alternative waste disposal methods rather than dumping sites. The combustion properties of these waste materials make them suitable for thermal disposal. A process has been developed in which the waste materials are burnt on an oscillating bar grate without supplying external energy. Electrical energy and process steam are generated while small amounts of a sintered slag remain behind. (orig.).

Energy Technology Data Exchange (ETDEWEB)

Pyrheliometric methods are described (particularly methods for measuring the solar constant), and theoretical and experimental studies in this field are surveyed and systematized. Particular attention is given to the analysis of instruments intended for pyrheliometers used as standards, reference instruments, and solar-constant meters is examined, and consideration is given to methods for determining the thermal-radiation properties of absorbing coatings and methods for calculating the absorption coefficients of cavity receivers.

Energy Technology Data Exchange (ETDEWEB)

The examples discussed demonstrate that in order to improve further the high-temperature strength properties of (monocrystalline) nickel-base superalloys, it is expedient to follow two parallel routes, namely alloy development, on the one hand, and suitable modifications of the microstructure by appropriate thermal and mechanical treatments, on the other hand. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Most of the Turkish lignites have undesired fuel properties and they are extremely polluting. In this study, Sweet Sorghum was chosen as the energy plant. Combustion experiments of lignite and lignite-Sweet Sorghum mixtures were carried out in a fluidised bed system. The fuel-feeding ratio was set such that the thermal output of the system remained constant. Addition of Sweet Sorghum to the lignite reduces the pollutant concentration. The results were supported by experimental results.

International Nuclear Information System (INIS)

This document is a summary of the available information on the thermo-hydro-mechanical properties of the bentonite barrier of a high-level radioactive waste repository and of the processes taking place in it during the successive repository operation phases. Mainly the thermal properties, the volume change processes (swelling and consolidation), the permeability and the water retention capacity are analysed. A review is made of the existing experimental knowledge on the modification of the these properties by the effect of temperature, water salinity, humidity and density of the bentonite, and their foreseen evolution as a consequence of the processes expected in the repository. The compiled evolution refers mostly to the FEBEX (Spain), the MX-80 (USA) and the FoCa (France) bentonite, considered as reference barrier materials in several European disposal concepts. (Author) 102 refs.

British Library Electronic Table of Contents (United Kingdom)

Metal iodates with a lone-pair containing I(V) that is in an asymmetric coordination geometry can form a diversity of unusual structures and many of them are promising new second homonic generation (SHG) materials. They exhibit wide transparency wavelength regions, large SHG coefficients and high optical-damage thresholds as well as moderately high thermal stability. In this paper, the structures and properties of the metal iodates are reviewed. The combination of d0 transition-metal cations with the iodate groups afforded a large number of metal iodates, with cations covering alkali metal, alkaline earth and lanthanide elements. Many of them are noncentrosymmetric (NCS) and display excellent SHG properties due to the additive effects of polarizations from both types of the asymmetric unit...

British Library Electronic Table of Contents (United Kingdom)

Abstract A series of polypropylene carbonate (PPC)/ZnO nanocomposite films with different ZnO contents were prepared via a solution blending method. The morphological structures, thermal properties, oxygen permeability, water sorption, and antibacterial properties of the films were investigated as a function of ZnO concentration. While all of the composite films with less than 5 wt % ZnO exhibited good dispersion of ZnO in the PPC matrix, FTIR and SEM results revealed that solution blending did not lead to a strong interaction between PPC and unmodified ZnO. As such, poor dispersion was induced in the composite films with a high ZnO content. By incorporating inorganic ZnO filler nanoparticles, the diffusion coefficient, water uptake in equilibrium, and oxygen permeability decreased as the ...

International Nuclear Information System (INIS)

When operating a nuclear power plant the necessity arise to eliminate various defects of building constructions, to seal joints and transitional elements. The authors present data concerning the production of a sealing composition made of epoxy resin and used for NPP premises of emergency location. Analytical relations are presented between the properties of the composition (adhesion strength, water absorption and others) and its structure. Physical, mechanical and thermal properties and structural peculiarities are determined in the process of interaction between the filling and binding agents. The composition sustains sealing properties under environmental conditions at he presence of an air - vapour mixture with 160 degrees C"o temperature and 0.3 MPa surplus pressure. (author).

Energy Technology Data Exchange (ETDEWEB)

The phase transformations and properties of a precipitation-hardened Ni-Cr-based alloy are investigated as a function of C, B, Nb, and Cr contents. It is found that the primary role of Nb consists in the formation of an independent phase, delta-Ni3Nb, a part of a gamma/gamma-prime-delta eutectoid (for high C and B concentrations) and in stimulating the gamma-sigma reaction consecutively with the gamma double prime-delta reaction (for low C and B concentrations). In both cases, the long-term strength characteristics of the Nb-alloyed system are relatively low. The substitution of boron for carbon contributes to a reduction in the number of nucleation sites for topologically close-packed phases and to the formation of more stable (with respect to excess compounds) M3B2 and MB2 borides. The high-boron material exhibits better properties and phase stability under mechanical and thermal loading. 13 references.

Energy Technology Data Exchange (ETDEWEB)

In this study, SnO{sub 2} thin films have been grown using spray pyrolysis technique on glass substrates under a substrate temperature (T{sub s} = 440 {sup o}C). The precursors were methanol CH{sub 4}O and anhydrous tin tetrachloride. XRD analyses yielded strong (1 1 0)-(1 0 1)-(2 0 0) X-ray diffraction peaks which are characteristics to tetragonal crystals. Atomic Force Microscopy (AFM) analyses showed the existence of clusters with particular pyramidal shapes. The main part of this study concerns the optical measurements of transmittance T({lambda}) and reflectance R({lambda}) spectra inside 250-1800 nm domain. Conjoint optical and thermal properties were deduced using the Amlouk-Boubaker Opto-Thermal Expansivity {psi}{sub AB}. The obtained value: {psi}{sub AB} {approx} 23.4 m{sup 3} s{sup -1} helped situating the performance of the as-grown SnO{sub 2} compound among most known PV-T oxides like ZnO and TiO{sub 2}.

Energy Technology Data Exchange (ETDEWEB)

The development of a silicon carbide (SiC) heat exchanger is a critical step in the development of the Externally-Fired Combined Cycle (EFCC) power system. SiC is the only material that provides the necessary combination of resistance to creep, thermal shock, and oxidation. While the SiC structure materials provide the thermomechanical and thermophysical properties needed for an efficient system, the mechanical properties of the SiC tubes are severely degraded through corrosion by the coal combustion products. To obtain the necessary service life of thousands of hours at temperature, a protective coating is needed that is stable with both the SiC tube and the coal combustion products, resists erosion from the particle laden gas stream, is thermal shock resistant, adheres to SiC during repeated thermal shocks (start-up, process upsets, shut-down), and allows the EFCC system to be ...

Science.gov (United States)

The Bingham plastic constitutive model has been widely used to predict the post-yield behavior of electro- and magneto- rheological fluids (ER and MR fluids). However, if these fluids experience shear thinning or shear thickening, the Bingham plastic model may not be an accurate predictor of behavior, since the post-yield plastic viscosity is assumed to be constant. In a recent study, it was theoretically and experimentally demonstrated that the Herschel-Bulkley fluid model can be successfully employed when evaluating non- Newtonian post-yield behavior of ER and MR fluids. In this paper, the Herschel-Bulkley model is employed to include a detailed analysis of ER and MR fluid dynamics through pipes and parallel plates. Simplified explicit expressions for the exact formulation are also developed. It is shown that the proposed simplified model of the Herschel-Bulkley steady flow equations for pipes and parallel plates can be used as an accurate design tool while ...

Energy Technology Data Exchange (ETDEWEB)

The defects localization in power cables follows several steps: identification, pre-localization and precise localization. Pre-localization methods, other than echo-metry, are presented first: bridge methods, particular case of low voltage networks, future perspectives. Then, the precise localization methods are described: magneto-acoustic method, audible frequencies method. The particular case of underwater and high-voltage cables is considered too (oil and gas leaks detection). (J.S.)

Science.gov (United States)

This study presents a semi-active vibration control of a scaled two-span bridge structure. Magneto-rheological fluid dampers are utilized as the semi-active energy absorbing devices, and a bridge vibration control system is developed. Closed-loop control system based on fuzzy logic is used to suppress the bridge deck motion under random excitation. It is demonstrated that this fuzzy logic control system can significantly reduce the relative deck displacement using about 60% less power compared to passive on state, while the absolute deck acceleration remains practically unchanged.

CERN Document Server

Individual laser cooled atoms are delivered on demand from a single atom magneto-optic trap to a high-finesse optical cavity using an atom conveyor. Strong coupling of the atom with the cavity field allows simultaneous cooling and detection of individual atoms for time scales exceeding 15 s. The single atom scatter rate is studied as a function of probe-cavity detuning and probe Rabi frequency, and the experimental results are in good agreement with theoretical predictions. We demonstrate the ability to manipulate the position of a single atom relative to the cavity mode with excellent control and reproducibility.

Energy Technology Data Exchange (ETDEWEB)

Recently, the development of shape memory alloy (SMA) actuators, in the forms of wire, thin film and stent have been found increasingly in the fields of materials science and smart structures and engineering. The increase in attraction for using these materials is due to their many unique materials, mechanical, thermal and thermal-mechanical properties, which in turn, evolve their subsequent shape memory, pseudo-elasticity and super-elasticity properties. In this paper, a common type of SMA actuator, Nitinol wires, were embedded into advanced composite structures to modulate the structural dynamic responses, in terms of natural frequency and damping ratio by using its shape memory and pseudo-elastic properties. A simple theoretical model is introduced to estimate the natural frequency of the structures before and after actuating the embedded SMA wires. The damping ratios of ...

Energy Technology Data Exchange (ETDEWEB)

Concerning high performance composite solid propellant BAMO and BAMO-based copolymers, synthetic method and properties of them were studied. Comparison graph of theoretical specific impulse for various propellants were shown, by that, reason why highest specific impulse BAMO was selected as direction of the study. As the orientation of synthesis, those were indicated that radicals at both ends should be hydroxyl so as urethane bonding was available, that liquid at normal temperature was required for easy handling, and that glass transition temperature is required to be low enough. Synthesis was conducted by ring-opening polymerization of ring ether detail procedures of which were explained. Measurements of properties was performed for thermochemical properties, thermal decomposition, combution heat, and friction sensitivity test to confirm safety. As the result, those were understood that ...

Energy Technology Data Exchange (ETDEWEB)

Since ionic liquids (ILs) possess several attractive properties, including chemical and thermal stability, nonflammability, high ionic conductivity, and negligible vapor pressure, a new electrolyte system based on ILs has been proposed for chip type aluminum electrolytic capacitors. Four ILs based on imidazolium/pyrrolidinium cations and maleate/phthalate anions have been synthesized and their thermal stabilities have been examined. The 25wt.% solutions of the four ILs in gamma-butyrolactone (GBL) solvent were prepared as electrolytes of chip type aluminum electrolytic capacitors. The conductivity, sparking voltage and thermal stability of these electrolytes have been systematically investigated. The results revealed that the four IL-based electrolytes exhibited high conductivity. Furthermore, the conductivity of maleate anion-based electrolytes is higher than that of phthalate anion-based electrolytes, ...

British Library Electronic Table of Contents (United Kingdom)

Nanomaterials are increasingly being used to modify adhesives used in aerospace and materials applications. Improvements in thermal and mechanical properties have been found by incorporation of small amounts of nanosize materials in to such adhesives. However, the introduction of nanomaterials to adhesives used in civil engineering applications is still a new approach which needs to be explored, especially in retrofitting of structures. This paper presents part of an ongoing research to address the effect of adding nanomaterials to modify a thermosetting adhesive used for bonding carbon fibre reinforced polymer (CFRP) composites to concrete members. Vapour grown carbon fiber (VGCF) was chosen to modify the adhesive. Different concentrations of carbon nanofibres PR-24 XT-LHT were adopted fo...

British Library Electronic Table of Contents (United Kingdom)

Glass ceramics are commonly used as sealing materials for planar solid oxide fuel cells (SOFCs). The major requirements of stack and module builders for these materials are the stability of the coefficient of thermal expansion (CTE), excellent bonding (sticking) behaviour and the absence of volatile ingredients, which can lead to changes of the material properties and the sealing ability. SCHOTT Electronic Packaging has developed special glasses and glass-ceramics for various solid oxide fuel cell designs and operating temperatures. The glass compositions are based on the system MgO-Al2O3-BaO-SiO2-B2O3. In this study the evaluation of the developed materials was done by high temperature aging tests for up to 1000h, high temperature XRD-studies and Rietveld calculations, combined with scann...

Energy Technology Data Exchange (ETDEWEB)

A new class of low aspect ratio toroidal hybrid stellarators is found using more general plasma confinement optimization criterion than quasi-symmetrization. The plasma current profile and shape of the outer magnetic flux surface are used as control variables to achieve near constancy of the longitudinal invariant J* on internal flux surfaces (quasi-omnigeneity), in addition to a number of other desirable physics target properties. We find that a range of compact (small aspect ratio A), high {beta} (ratio of thermal energy to magnetic field energy), low plasma current devices exist which have significantly improved confinement both for thermal as well as energetic (collisionless) particle components. With reasonable increases in magnetic field and geometric size, such devices can also be scaled to confine 3.5 MeV alpha particle orbits.

British Library Electronic Table of Contents (United Kingdom)

Medium-density polyethylene/multiwall carbon nanotube (MDPE/MWCNT) nanocomposites were produced by a mechanical milling method using a high-energy ball mill. The MDPE and MWCNTs were added to the ball mill at a constant 20:1 weight ratio of ball/powders and milled for 10 h to obtain polyethylene matrix nanocomposites reinforced with 0.5, 1, 2.5, and 5 weight percent of MWCNTs. To clarify the role of both MWCNT content and milling time on the morphology of MDPE, some nanocomposite samples were investigated by using a scanning electron microscope. To evaluate the role of milling on the microstructure of the nanocomposites, very thin films of MDPE/MWCNTs were prepared and studied by transmission electron microscopy. Thermal behavior of these nanocomposites was investigated by using differenti...

British Library Electronic Table of Contents (United Kingdom)

Density functional theory calculations were performed to study the effects of different substituents and bridge groups on the heats of formation (HOFs), thermal stability, and detonation properties for a series of diiminotetrazole derivatives. The isodesmic reaction method was employed to calculate the HOFs of the derivatives using total energies obtained from electronic structure calculations. The bond dissociation energies and bond orders for the weakest bonds were analyzed to investigate the thermal stability of the diiminotetrazole derivatives. The detonation velocities and pressures were evaluated by using the semiempirical Kamlet-Jacobs equations, based on the theoretical densities and HOFs. These results provide basic information for the molecular design of novel high-energy density...

Energy Technology Data Exchange (ETDEWEB)

Fatty acids such as stearic acid (SA), palmitic acid (PA), myristic acid (MA), and lauric acid (LA) are promising phase change materials (PCMs) for latent heat thermal energy storage (LHTES) applications, but high cost is the most drawback which limits the utility area of them in thermal energy storage. The use of fatty acids as form-stable PCM will increase their feasibilities in practical LHTES applications due to reduced cost of the energy storage system. In this regard, a series of fatty acid/poly(methyl methacrylate) (PMMA) blends, SA/PMMA, PA/PMMA, MA/PMMA, and LA/PMMA were prepared as new kinds of form-stable PCMs by encapsulation of fatty acids into PMMA which acts as supporting material. The blends were prepared at different mass fractions of fatty acids (50, 60, 70, 80, and 90% w/w) to reach maximum encapsulation ratio. All blends were subjected to leakage test by heating the blends over the melting temperature of the PCM. The blends ...

Energy Technology Data Exchange (ETDEWEB)

Two types of thermal control materials based on polyimide film UPILEX-R are designed. One of thermal control material R/Al is coated with Al on the back surface. The other of thermal control material TCC/R/Al is coated with transparent conductive coating on the font surface and is coated with Al on the balk surface. The solar absorptance is measured spectroscopically with an integrating sphere in the wavelength region of 0.26 - 2.50 {mu}m and the total hemispherical emittance is measured calorimetrically in the temperature range of -100-+100{degree}C for the present thermal control materials. To evaluate the space degradation of optical properties (refractive index, extinction coefficient, absorption coefficient) on UPILEX-R film and solar absorptance on thermal control materials, space environment simulation tests are performed on the ground with independent ...

International Nuclear Information System (INIS)

In the feasibility study on commercialized FBR systems, the application of 12Cr steel, with its physical properties and high-temperature strength properties, as structural material is considered in order to greatly reduce construction costs by compacted instruments and structures. In this report, creep, fatigue and the creep-fatigue properties of Mod.9Cr-1Mo steel forging (thickness 550mm) weld, representing conventional steels, were evaluated in order to obtain the needed basic data for the evaluation of the high-temperature strength of 12Cr steel weld. The results obtained are as follows: (1) Metal suitable for HAZ was made by applying thermal treatment to simulate the thermal hysteresis during welding to clearly define creep and fatigue properties in a HAZ softened zone. (2) Creep strength of the weld metal and the welded joint was equal to that of the base ...

Energy Technology Data Exchange (ETDEWEB)

Specimens of glassy Pd{sub 80}Si{sub 20} were irradiated at temperatures below 100K with 3.5 MeV krypton ions. After irradiation, changes in the sound velocity were measured at 80 K without warm-up by Brillouin scattering. The sound velocity decreased with increasing ion fluence and exponentially approached a saturation value of -4.7%. The change in the shear elastic modulus per unit concentration n of defects was estimated to be d(ln C)/dn = -9.4 to -4.7. The results of the present study are compared with changes in the elastic properties predicted recently by an interstitialcy model for glassy metals, and with the elastic properties of glassy metals after thermal treatment.

International Nuclear Information System (INIS)

Electron beam (EB) processing involves using electrons to initiate polymerization or cross-linking reactions in suitable substrates, thereby enhancing specific physical and chemical properties. A relatively new use of EB processing is now emerging: the production of fibre-reinforced composites. EB curing at ambient temperature has the potential to reduce the residual stresses in an advanced composite, a result of expansion during thermal curing, and to significantly increase the overall cure speed and process throughput. Wood fibres are used as a filler material for various thermoplastics such as polypropylene. EB treatment, combined with selected EB-curable coupling agents, significantly increases the adhesion between the wood fibres and the thermoplastic polymer, resulting in improved material properties. Work to develop both products and processes for the EB curing of fibre-reinforced composites is currently underway at ...

International Nuclear Information System (INIS)

First-principles density functional theory (DFT) based calculations were performed to study the electronic and cohesive properties of all the intermediate ordered phases appearing in the transformation from bcc-based #beta# to hexagonal ordered #omega# phase in Zr_3Al alloy. Full-potential linear augmented plane wave (FPLAPW) method under the GGA was employed to establish the stability hierarchy and structure-property correlations. Further, effective pair potentials upto the fourth nearest neighbours were extracted, which, subsequently, were used for the thermodynamics analysis of the thermally-induced #beta##->##omega# transformation. The lattice collapse mechanism involving the concept of the onset of a displacement wave where the extent of collapse is viewed as an amplification of the displacement wave was employed for further analysis. (author)

International Nuclear Information System (INIS)

Irradiation processing of food in the prepackaged form may affect chemical and physical properties of the plastic packaging materials. The effect of #gamma#-irradiation doses (2.5-10.0 kGy) on polypropylene (PP)-based retortable food packaging materials, were investigated using Fourier transform infrared (FTIR) spectroscopic analysis, which revealed the changes happening to these materials after irradiation. The mechanical properties decreased with irradiation while oxygen transmission rate (OTR) was not affected significantly. Colour measurement indicated that Nylon 6 containing multilayer films became yellowish after irradiation. Thermal characterization revealed the changes in percentage crystallinity.

International Nuclear Information System (INIS)

Different semi precious alloys (Pd-Ag, Pd-Au) have been studied after thermal oxidation treatments to analyze the mechanical improvement of the interface between the metal and the ceramic. Using the four point bending test, the authors have analyzed the different steps corresponding to the mechanical evolution of the bi-material : cracking energy on the surface, relaxation energy after first cracking, propagation energy of cracks at the interface zone. It has been shown that some alloys only have a high resistance to the interface cracking and the role played by the interface reactions to improve this property. (orig.).

International Nuclear Information System (INIS)

Thermochromic tungsten-doped vanadium dioxide (VO2) powders were successfully synthesized by thermal reduction using V2O5 as a vanadium precursor. The products were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM) and differential scanning calorimetry (DSC). The results indicated that W was successfully doped into the crystal lattice of VO2 matrix, and prepared tungsten-doped VO2 had a rod-like morphology. The effects of reducing temperature and annealing temperature on the crystallographic structures were also discussed. The phase transition temperature (Tt) of VO2 could be simply tuned by changing the doping concentration of tungsten. When the doping concentration was 1.58 mol%, the Tt could be reduced to 37.8 oC from initial 69.5 oC, suggesting that tungsten-doped VO2 possesses prominent thermochromic properties and optical switching characters. It has shown that this ...

International Nuclear Information System (INIS)

In the present study a partial replacement of aggregate with two different ratios of waste rubber (5%, 10%) with the addition of a constant ratio of rice husk ash (RHA), 5% was carried out. The hardened cement mortar used the optimum water of consistency. The specimens were molded into 1 inch cubic moulds .The specimens were first cured for 24 hours, at 100% relative humidity and then cured under tap water for 3, 7 and 28 days followed by irradiation at different doses of gamma irradiation namely 5 and 10 kGy. The physico-chemical and mechanical properties such as compressive strength, total porosity and bulk density were studied for the three types of specimens. The results showed that the values of the compressive strength, bulk density and chemically combined water of the blended cement mortar paste (OPC-RHA) increase ,while blended cement mortar paste with 5% RHA and 5, 10% waste rubber decrease. The results were confirmed by scanning electron microscopy and ...

Energy Technology Data Exchange (ETDEWEB)

There is a growing interest in using {sup 242m}Am as a nuclear fuel. The advantages of {sup 242m}Am as a nuclear fuel derive from the fact that {sup 242m}Am has the highest thermal fission cross section. The thermal capture cross section is relatively low and the number of neutrons per thermal fission is high. These nuclear properties make it possible to obtain nuclear criticality with ultra-thin fuel elements. The possibility of having ultra-thin fuel elements enables the use of these fission products directly, without the necessity of converting their energy to heat, as is done in conventional reactors. There are three options of using such highly energetic and highly ionized fission products. - Using the fission products themselves for ionic propulsion. - Using the fission products in an MHD generator, in order to obtain electricity directly. - Using the fission products to heat a gas up to a high ...

Energy Technology Data Exchange (ETDEWEB)

Properly quantified performance of a solar-thermal cavity receiver must not only account for the energy gains and losses as dictated by the First Law of thermodynamics, but it must also account for the quality of that energy. However, energy quality can only be determined from the Second Law. In this paper an equation for the Second-Law efficiency of a cavity receiver is derived from the definition of available energy or availability (occassionally called exergy), which is a thermodynamic property that measures the maximum amount of work obtainable when a system is allowed to come into unrestrained equilibrium with the surrounding environment. The fundamental concepts of the entropy and availability of radiation are explored from which a convenient relationship among the reflected cone half angle, the insolation, and the concentrator geometric characteristics is developed as part of the derivation of the Second-Law efficiency. A comparison is ...

International Nuclear Information System (INIS)

Radiation-and-thermal-combined degradation of some kinds of cable insulating and jacketing materials was evaluated by accelerated aging tests. Plasticized polyvinyl chloride (PVC), silicone rubber, crosslinked and non-crosslinked halogen-free flame-retardant polyolefins (NH-XLPO and NH-PO) and ethylene-propylene rubber (EP rubber) of experimental formulation were degraded at accelerated rates, that are 50-1000 times the degradation rate under standard conditions (e.g.; 1Gy/h, 50degC), and a method to assess the lifetime of these materials under standard conditions was studied. The degradation was investigated by measuring tensile properties. In the accelerated aging tests, rates of elongation decrease owing to degradation for these materials were in proportion to the increase in accelerated rate. The PVC lifetime estimated from sequential aging tests had a tendency to extend beyond that from simultaneous aging tests, while the lifetime of other ...

International Nuclear Information System (INIS)

We report on the specific heat and the thermopower of UPdSn and UCuSn, both of which order antiferromagnetically at low temperatures. The compounds show similar behaviour in the specific heat, and the large magnetic-entropy changes around T_N are evidence for a large degree of 5f-electron localization. For both compounds, we find that thermopower results are consistent with the findings for the electrical resistance. While for UCuSn very abrupt changes at 25 and 60 K are observed for both quantities, more continuous changes at the magnetic transitions (25 and 40 K) are found for UPdSn. (orig.).

International Nuclear Information System (INIS)

The effect of heat transfer is described from heat exchange tubes of a horizontal steam generator on the distribution of primary water to the individual tubes of the tube bundle. It is shown that in a broad interval of mass flow rates and lengths of heat exchange tubes, the simplified method of calcualtion, i.e., calculation of the distribution of primary water into heat exchange tubes neqlecting the changes of physical properties of water along the heat exchange tubes, will yield sufficiently accurate results. (author).

Energy Technology Data Exchange (ETDEWEB)

Solutions are obtained for the Einstein field equations governing 40 rotating and time-dependent Bianchi type-IX cosmologies with thermal and nonthermal perfectly fluid sources. Some general properties of the solutions are discussed, and the exact computational details are given in a companion paper. All the cosmologies have spacelike, timelike or null-like homogeneous hypersurfaces depending on whether the constant alpha is less than or greater than one. The pressure of the cosmologies is assumed to be zero, and the energy density is less than zero. 9 references.

Energy Technology Data Exchange (ETDEWEB)

A study was undertaken of problems encountered in the use of thermal power station coal ash and red mud (an aluminium smelting residue) as a banking or filling material, the aim being the effective utilization of these substances. Like clinker, coal ash and red mud can also be used as improvers, but there are various problems such as absorption swelling, strong alkalinity, and the difficulty of controlling the moisture content. Certain measures have to be carried out in on-site use to combat these problems. (11 refs.)

Energy Technology Data Exchange (ETDEWEB)

Three-dimensional magnetohydrodynamic simulations are executed in a full toroidal geometry to clarify the physical mechanisms of the Internal Reconnection Event (IRE), which is observed in the spherical tokamak experiments. The simulation results reproduce several main properties of IRE. Comparison between the numerical results and experimental observation indicates fairly good agreements regarding nonlinear behavior, such as appearance of localized helical distortion, appearance of characteristic conical shape in the pressure profile during thermal quench, and subsequent appearance of the m=2/n=1 type helical distortion of the torus. (author)

International Nuclear Information System (INIS)

The neutron data required to completely analyze fission reactors includes many isotopes and covers a broad energy range. In both fast and thermal reactors, the neutron inventory is a fine balance determined by the fission properties of "2"3"5U, "2"3"9Pu and "2"3"8U and by the capture cross sections of "2"3"8U, fuel materials, structural materials and coolant materials. In fast reactors, the spectrum of neutrons ranges from 1 keV to 3 MeV and is influenced by the elastic and inelastic scattering properties of "2"3"8U and the structural and coolant materials. For neutron shielding applications, the important neutron data include the total cross sections of structural and coolant materials in the MeV range. The impact of these basic nuclear data in fission reactor applications is most suitably described by sensitivity analysis. For example, sensitivity coefficients computed for a typical large plutonium fueled fast reactor ...

Science.gov (United States)

To fulfill the President s Vision for Space Exploration - successful human and robotic missions between the Earth and other solar system bodies in order to explore their atmospheres and surfaces - NASA must reduce trip time, cost, and vehicle weight so that payload and scientific experiment capabilities are maximized. As a collaboration among NASA Centers, this project will generate products that will enable greater fidelity in mission/vehicle design trade studies, support risk reduction for material selections, assist in optimization of vehicle weights, and provide the material and process templates for development of human-rated qualification and certification Thermal Protection System (TPS) plans. Missions performing aerocapture, aerobraking, or direct aeroentry rely on technologies that reduce vehicle weight by minimizing the need for propellant. These missions use the destination planet s atmosphere to slow the spacecraft. Such mission profiles induce heating ...

Science.gov (United States)

This paper presents a semi-active vibration control of a scaled two-span bridge structure. Magneto-rheological fluid dampers are utilized as the semi-active energy absorbing deices and a bridge vibration control system is developed. Closed-loop control system based on fuzzy logic is used to suppress the bridge deck motion under random excitations. The sufficient condition for the closed-loop stability of the fuzzy control system is derived from the variable structure system theory. It is demonstrated that this stable fuzzy control system can significantly reduce the relative deck displacement using about 55 percent less power compared to passive-on state, while the absolute deck acceleration is relatively unaffected.

British Library Electronic Table of Contents (United Kingdom)

Purpose - The purpose of this paper is to investigate the accuracy of different force calculation methods and their impact on mechanical deformations. For this purpose, a micrometer scaled actuator is considered, which consists of a micro-coil and of a permanent magnet (PM) embedded in a deformable elastomeric layer. Design/methodology/approach - For the magnetic field evaluation a hybrid numerical approach (finite element method/boundary element method (FEM/BEM) coupling and a FEM/BEM/Biot-Savart approach) is used, whereas FEM is implemented for the mechanical deformation analysis. Furthermore, for the magneto-mechanical coupling several force calculation methods, namely the Maxwell stress tensor, the virtual work approach and the equivalent magnetic sources methods, are considered and co...

British Library Electronic Table of Contents (United Kingdom)

In this study structural and magnetic character of the expanded austenite phase (gN) layer formed on a medical grade CoCrMo alloy by a low-pressure Radio-Frequency plasma nitriding process was investigated. The formation of the expanded austenite phase is facilitated at a substrate temperature near 400^oC for 1, 2, 4, 6 and 20h under a gas mixture of 60% N2-40% H2. The magnetic state of the gN layers was determined by a surface sensitive technique, magneto-optic Kerr effect (MOKE), and with a scanning probe microscope in magnetic force mode (MFM). Strong evidence for the ferromagnetic nature of the gN-(Co,Cr,Mo) phase is provided by the observation of stripe domain structures and the hysteresis loops. The ferromagnetic state for the gN phase observed here is mainly linked to large lattice ...

International Nuclear Information System (INIS)

The thermodynamics of the Sr-Si system is of fundamental importance for the understanding of eutectic modification of Al-Si alloys. At the same time, strontium silicides have recently been found to have potential applications in electronic devices. Renewed research efforts have led to a re-evaluation of the phase equilibria in this system, resulting in the discovery of previously undetected stable intermetallic compounds. In this work, we investigate the finite temperature thermodynamic properties of the stable (and metastable) Sr-Si intermetallics. The vibrational properties of the intermetallic compounds are calculated within harmonic theory, with quasi-harmonic corrections to account for the effects of thermal expansion. The total free energies of the compounds are computed considering vibrational and electronic contributions, as well as weak anharmonic corrections. The ground state of the system is predicted and ...

British Library Electronic Table of Contents (United Kingdom)

Abstract Many (K1-xNax)NbO3 (KNN)-based ceramics with high piezoelectric performance exhibit undesirable strong temperature dependence due to the orthorhombic-tetragonal polymorphic phase transition near room temperature. In order to improve the temperature stability of the ceramics, many additives have been added into the KNN-based ceramics to shift TO-T down to below room temperature. Contrary to the previous approach (Na0.53K0.47-xAgx)Nb1-xSbxO3 (NKANS) ceramics with TO-T well above room temperature have been prepared by a conventional solid-state reaction method. The density and the electrical properties are effectively improved by the addition of AgSbO3, and optimum piezoelectric properties are found in the ceramics with 0.05---x---0.07, with maximum kp---0.46 for NKANS5 and maximum d...

Energy Technology Data Exchange (ETDEWEB)

The entrapment of proteins using the sol-gel route provides a means to retain its native properties and artificially reproduce the molecular crowding and confinement experienced by proteins in the cell allowing investigation of the physico-chemical and structural properties of biomolecules at the biotic/abiotic interface. The biomolecules are spatially separated and 'caged' in the gel structure but solutes can freely permeate the matrix. Thus, properties such as the folding of ensembles of individual molecules can be examined in the absence of aggregation effects that can occur in solution studies. Green fluorescent protein from Aequorea coerulescens was used as a model protein to examine the unfolding/re-folding properties of protein in silica gels. The recombinant protein was isolated and purified from Escherichia coli extracts by cell lysis, three-phase partitioning, dialysis, and ...

Energy Technology Data Exchange (ETDEWEB)

In this work, ZnO thin films have been grown on glass substrates by using a solution of propanol (C{sub 3}H{sub 8}O), water (H{sub 2}O) and zinc acetate (Z{sub n}(CH{sub 3}CO{sub 2}){sub 2}) in acidified medium (pH 5). The obtained films were n doped with ytterbium (Yb) at the rates of 100, 200 and 300 ppm. The structural features of the doped films were investigated using XRD, atomic force microscopy and scanning electronic microscopy techniques. XRD analysis shows a strong (0 0 2) X-ray diffraction line for increasing Yb-doping amounts. This c-axis preferential orientation of ZnO crystallites is naturally required to use this oxide as transparent conductor in optoelectronic applications. Atomic force microscopy (AFM) analysis shows an enhancement in the surface roughness of the doped ZnO:Yb thin films. Optical measurements were performed in 300-1800 nm domain via transmittance T(lambda) and reflectance R(lambda) spectra. Conjoint optical and thermal ...

Energy Technology Data Exchange (ETDEWEB)

In this work, {beta}-SnS{sub 2} thin films have been prepared on glass substrates by the spray pyrolysis technique using an alcohol solution which contains tin chloride (SnCl{sub 4}) and thiourea (SC(NH{sub 2}){sub 2}) as precursors. The structural study shows that {beta}-SnS{sub 2} thin film prepared using optimal experimental conditions: substrate temperature T{sub s} = 280 deg. C and the concentration ratio of sulfur and tin elements in the spray solution x = [S]/[Sn] = 2.5, crystallizes in the hexagonal phase with a strong (0 0 1) X-ray diffraction line. In the same way, microprobe analyses (EPMA) as well as X-ray photoelectron spectroscopy (XPS) show the presence of undiserable phase of SnO{sub 2}. From the transmission and reflectance spectra, the band gap energy is 2.65 eV. On the other hand, the photothermal properties of such films have been studied, the thermal conductivity was K{sub c} = 0.85 W m{sup -1} K{sup -1} and the ...

International Nuclear Information System (INIS)

We succeeded in synthesizing a new cubic intermetallic compound PrCu_4Ag in a fcc structure. Measurements of X-ray diffraction, magnetic susceptibility, magnetization, specific heat, electrical resistivity, thermal expansion, and elastic constants have been performed on single crystals of PrCu_4Ag. A maximum value of #chi#(T) with a corresponding peak in C(T) suggests that an antiferromagnetic phase transition occurs at T_N=2.4 K, where a sudden decrease in #rho#_4_f(T) and a sharp peak in the thermal expansion coefficient #alpha#(T) were observed. Characteristic Curie-type softening was observed in the temperature dependence of the transverse mode for (C_1_1 - C_1_2)/2 and C_4_4 from 70 K down to T_N, which implies that the crystalline electric field (CEF) ground state is the magnetic triplet #GAMMA#_5. The anisotropic properties in M(T,H) and C(T,H) are studied when the external magnetic field is applied in the ...

International Science & Technology Center (ISTC)

Development of Oxygen Ion-Implanted Collector materials for Thermal Emission Converters of Thermal Energy into the Electric One.

Energy Technology Data Exchange (ETDEWEB)

In this work some physicochemical properties and the thermal behavior and stability of sour sop or guanabana (Annona muricata) seed almond oil were studied by means of chemical, DSC and TG analysis. The results showed that the almond has 2.5% ash, 17.9% crude fiber, 15.7% protein, 26.0% de carbohydrates and 37.7% oil (dry base). The composition of almond oil showed 68.5% unsaturated fatty acids, mainly oleic and linoleic, and some palmitoleic acids, and 31.5% saturated, principally palmitic and stearic fatty acids; refraction index was 1.468 and saponification and iodine value were 168.2 and 87.0, respectively. DSC thermal analysis showed that oil crystallization initiates at -4.5 degree centigrade and ends at -79.0 degree centigrade with a crystallization enthalpy of 48.2 J/g; the oil melts in a temperature range from -42.4 to -16.9 degree centigrade, with a maximum peak at -15 degree centigrade and a fusion enthalpy of ...

Energy Technology Data Exchange (ETDEWEB)

A joint materials test program developed by the Institute for Mining and Minerals Research (IMMR) and the Tennessee Valley Authority (TVA) involved the postexposure mechanical properties and corrosion behavior of candidate structural materials in an experimental, atmospheric fluidized-bed combustor (AFBC). This combustor was operated by Accurex Corporation at Research Triangle Park, North Carolina, under the direction of TVA. The materials studied were Type 304, Type 310, and INCOLOY alloy 800 in the form of disc coupons with and without crevice configurations. Type 304 was also used for mechanical property measurements. The alloys were exposed to the combustor environment at about840/sup 0/C for approximately 330 hours. The ranking in terms of decreasing weight loss was: (1) Type 304, (2) Type 310, and (3) INCOLOY alloy 800. The presence of tight crevices did not enhance the corrosion rate. In addition, the corrosion rates, based on the weight ...

Energy Technology Data Exchange (ETDEWEB)

For reduction of the amount of waste plastics, the paper summarized the actual recycling state and the present recycling technology in Japan. A total plastic discharge amount of Japan in 1995 is 8.84 million tons, approximately 60% of all the production amount, 950,000 tons of which are recycled. Reutilized are pallets and containers in the physical distribution field. Recycling is a cascade recycling to the usage field where the degree of the required properties is lower than that of products used in virgin. As to making it a chemical material, chemical recycling technology by depolymerization has been developed. Thermal recycling is a strong method where combustion heat energy of waste plastics is used for steam production and power generation. The thermal recycling is divided into a direct combustion method and a method of use as fuel. Keys to promote and settle recycling are summarized to the following five: promotion ...

Energy Technology Data Exchange (ETDEWEB)

Polycrystalline ZnS semiconducting films have been prepared in sandwich configuration by spray pyrolysis technique using ZnO-coated glass substrates and mixed aqueous solutions of ZnCl{sub 2} and thiourea. The sandwich structures have been produced successfully by means of ZnO-coated glass substrates. The produced ZnS films have been crystallized in a wurtzite structure and had a direct band gap energy of 3.62 eV. The electrical properties of the sample have been studied by an analysis based on the thermally stimulated current spectra in the temperature range of 40-300 K with various heating rates. A set of curves of I (T) for varying initial density of filled traps at a heating rate of {beta} {sub 2}=0.06 K s{sup -1} indicate that the observed peaks in the TSC curve of polycrystalline ZnS films have first-order features. In order to evaluate the trap parameters of ZnS films, we have used curve-fitting method. The values of the frequency factor ...

Energy Technology Data Exchange (ETDEWEB)

The dispersion of more than 20 vol pct submicrometer ceramic particles within a metallic matrix and the deposition of such a cermet to form a thick and tough coating presents problems. Most of the coating techniques have failed in attempting to homogeneously disperse very fine and hard particles in large amounts while avoiding their decomposition or reaction with the metal matrix during the deposition process. A simple and efficient method has been developed for producing ceramic-containing composite coatings. It consists in synthesizing cermet-based materials and in depositing them by a rapid solidification process, such as thermal spraying. Boride- and carbide-based materials have been successfully obtained by plasma spraying reactive powders comprising the basic reagents. These materials, with a microstructure of submicrometer ceramic particles dispersed in a metallic matrix, exhibit good wear-resistant properties (abrasion and sliding ...

Energy Technology Data Exchange (ETDEWEB)

The results of the laboratory studies performed by CIEMAT with the FEBEX bentonite in the context of WP3.2 of the NF-PRO Project and of the Agreement ENRESA-CIEMAT Anexo V are presented and analysed in this report. They refer to the effect of the hydraulic gradient on the permeability of bentonite, the effect of the thermal gradient on the hydration kinetics of bentonite, and the repercussion of temperature on the hydro-mechanical properties of bentonite (swelling, permeability and water retention capacity). In all the cases the bentonite has been used compacted to densities expected in the engineered barrier of a high-level radioactive waste repository. The existence of threshold and critical hydraulic gradients has been observed, both of them dependent on bentonite density and water pressures. After more than seven years of hydration, the 40-cm high bentonite columns are far from full saturation, the thermal gradient ...

International Nuclear Information System (INIS)

Heat losses in duct flow and heat transfer enhancement are investigated through an analysis of natural convection about a horizontal cylinder with a porous or fibrous coating. The porous substrate may be used for two purposes. According to its properties, it may be employed as an insulating material or as a means to surface augmentation. An optimization study is then carried out in order to find the best conditions that allow good thermal insulation or heat transfer rate improvement. The flow motion and heat transfer coefficient are predicted for various conditions. The results show that an efficient insulation which means less than 10% in heat losses is obtained for a porous layer thickness of 0.8x tube diameter and a permeability corresponding to Da #<=# 10"-"7. Nevertheless, there is a Darcy number limit above which convection must be accounted for. Porous or fibrous materials may also be used as a heat transfer augmentation technique. To ...

Energy Technology Data Exchange (ETDEWEB)

Radiation-and-thermal-combined degradation of ethylene-propylene rubber (EP rubber) and chlorosulfonated polyethylene (CSM) as cable insulating and jacketing materials were evaluated by accelerated aging tests and a method to assess the lifetime of these materials under practical application was studied. EP rubber and CSM of experimental formulation were degraded at accelerated rates, that are 50 [approx] 1000 times the degradation rate under a standard condition (1Gy/h, 50degC). The degradation was investigated by measuring the tensile properties. In the accelerated aging tests, rates of elongation decrease owing to degradation for both EP rubber and CSM were in proportion to increase in accelerated rate. Behaviors of elongation changes showed little difference with accelerated rate. EP rubber lifetime estimated from sequential aging test had a tendency to extend beyond that from simultaneous aging test, while CSM lifetime estimated from both ...

International Nuclear Information System (INIS)

A family of sealant materials has been developed for use in the solid oxide fuel cell (SOFC) and in other applications in the temperature range of 800 endash 1000 degree C. These materials are based on glasses and glass-ceramics in the SrO endash La_2O_3 endash Al_2O_3 endash B_2O_3 endash SiO_2 system. The coefficients of thermal expansion (CTE) for these materials are in the range of 8 endash 13x10"-"6/degree C, a good match with those of the SOFC components. These sealant materials bond well with the ceramics of the SOFC and, more importantly, form bonds that can be thermally cycled without failure. At the fuel cell operating temperature, the sealants have viscosities in the range of 10"4-10"6 Pa-s, which allow them to tolerate a CTE mismatch of about 20% among the bonded substrates. The gas tightness of a sample seal was demonstrated in a simple zirconia-based oxygen concentration cell. copyright 1996 Materials Research Society.

International Nuclear Information System (INIS)

Neutron semiconductor detectors for neutron counting and neutron radiography have an increasing importance. Simple silicon neutron detectors are combination of a planar diode with a layer of an appropriate neutron converter such as 6LiF. These devices have limited detection efficiency of not more than 5%. The detection efficiency can be increased by creating a 3D microstructure of dips, trenches or pores in the detector and filling it with a neutron converter. The first results related to the development of such devices are presented. Silicon detectors were fabricated with pyramidal dips on the surface covered with 6LiF and then irradiated by thermal neutrons. Pulse height spectra of the energy deposited in the sensitive volume were compared with simulations. The detection efficiency of these devices was about 6.3%. Samples with different column sizes were fabricated to study the electrical properties of 3D structures. Charge collection ...

Energy Technology Data Exchange (ETDEWEB)

A carbon-bonded carbon fiber (CBCF) insulation developed for a radioisotope heat source is made from chopped rayon fiber about 10 ..mu..m in diameter and 250 ..mu..m long, which is carbonized and bonded with phenolic resin particles. The CBCF is an excellent lightweight insulating material with a nominal density of 0.2 Mg/m/sup 3/ and a thermal conductivity of 0.24 W/(m-K) in vacuum at 2000/sup 0/C. Several attributes that make CBCF particularly suitable for the heat source application have been identified. These include light weight, low thermal conductivity, chemical compatibility, and high-temperature capabilities. The mechanical strength of CBCF insulation is satisfactory for the application. The basic fabrication technique was refined to eliminate undesirable large pores and cracks often present in materials fabricated by earlier techniques. Also, processing was scaled up to increase the fabrication rate by a factor of 10. The specific ...

Energy Technology Data Exchange (ETDEWEB)

Results of X-ray investigations of solid normal hydrogen are presented. Temperature dependences of the lattice parameteps, molar volumes, linear and volume expansion coefficients in the 2K-Tsub(melt) temperature range are obtaiped. An essential n-H/sub 2/ expansion anisotropy in the premelting temperature region is pointed out. It is shown that the hexagonal lattice parameter ratios over the whole investigated temperature range is considerably higher than for solid parahydrogen. A considerable difference in thermal expansion of normal hydrogen and parahydrogen in the low temperature region is revealed. It is caused by contribuation of a rotational subsystem, increasing with the temperature decrease to crystal expansion. A detailed analysis of solid n-H/sub 2/ thermodynamic properties is conducted. The data testifying to the presence of isomorphous phase transformation in the solid n-H/sub 2/ in the premelting temperature region are discussed.

British Library Electronic Table of Contents (United Kingdom)

Bacillus licheniformis ?-glutamyltranspeptidase (BlGGT) undergoes an autocatalytic process to generate 44.9 and 21.7?kDa subunits; however, a mutant protein (T399A) loses completely the processing ability and mainly exists as a precursor. For a comprehensive understanding of their structural features, the biophysical properties of these two proteins were investigated by circular dichroism and fluorescence spectroscopy. Tryptophan fluorescence and circular dichroism spectra were nearly identical for BlGGT and T399A, but unfolding analyses revealed that these two proteins had a different sensitivity towards temperature- and guanidine hydrochloride (GdnHCl)-induced denaturation. BlGGT and the unprocessed T399A displayed T m values of 61.4?C and 68.1?C, respectively, and thermal unfolding of b...

CERN Document Server

Quark Gluon Plasma transport coefficients for heavy quarks and quark-antiquark pairs are computed through an extension of the results obtained for a hot QED plasma by describing the heavy-quark propagation in the eikonal approximation and by weighting the gauge field configurations with the Hard Thermal Loop effective action. It is shown that such a model allows to correctly reproduce, at leading logarithmic accuracy, the results obtained by other independent approaches. The results are then inserted into a relativistic Langevin equation allowing to follow the evolution of the heavy-quark momentum spectra. Our numerical findings are also compared with the ones obtained in a strongly-coupled scenario, namely with the transport coefficients predicted (though with some limitations and ambiguities) by the AdS/CFT correspondence.

CERN Document Server

Monopolar charge disorder effects are studied in the context of fluctuation-induced interactions between neutral dielectric slabs. It is shown that quenched bulk charge disorder gives rise to an additive contribution to the net interaction force which decays as the inverse distance between dielectric surfaces. This effect may thus completely mask the standard Casimir--van der Waals effect. By contrast, annealed (bulk or surface) charge disorder leads to a net interaction force whose large-distance behavior coincides with the universal Casimir force between perfect conductors, which scales as inverse cubic distance, and the dielectric properties enter only in subleading corrections.

International Nuclear Information System (INIS)

Test Blanket Modules (TBM) will be tested in ITER to verify the capability of tritium breeding and recovery and the extraction of thermal energy suitable for the production of electricity. A Helium Cooled Solid Breeder (HCSB) TBM has been developed in Korea to accomplish these goals. Reduced Activation Ferritic/Martensitic (RAFM) steel has been chosen as the primary candidate structural material for Korean TBM. Due to the complexity of the First wall (FW) and Side wall (SW), it is necessary to develop various joining technologies, such as Hot Isostatic Pressing (HIP), Electron Beam Welding (EBW) and Tungsten Inert Gas (TIG) welding, for the successful fabrication of TBM. In this study, the mechanical properties of TIG welded RAFM steel were investigated. Various mechanical tests of TIG-welded RAFM steel were performed to obtain the optimized TIG welding process for RAFM steel

British Library Electronic Table of Contents (United Kingdom)

In this article, we describe a method used to prepare an in situ sodium-activated, organomodified bentonite clay/styrene-butadiene rubber nanocomposite master batch via a latex blending technique. The clay master batch was used for compound formulation. Octadecyl amine was used as an organic intercalate. The clay was purchased from local suppliers and was very cheap. Sodium chloride was used for in situ activation of the clay. The wide-angle X-ray diffraction data indicated that the in situ sodium activation helped to increase the intergallery distance from 1.28 to 1.88 nm. A transmission electron micrograph indicated intercalation and partial exfoliation. The thermal properties were relatively better in the case of the sodium-activated, organomodified bentonite-clay-containing compound. A...

Energy Technology Data Exchange (ETDEWEB)

Carbon films have been made by a variety of techniques, including evaporation, sputtering, and laser or thermal pyrolysis of organic polymers. Polyacrylonitrile (PAN) is often used as a carbon precursor, since low-temperature thermo-oxidative pretreatment produces a material which can be pyrolyzed without loss of shape. This is the basis for the production of carbon fibers with good mechanical properties. We report here the formation of very thin films of carbon (500 to 1500 A) by pyrolysis of spin-cast PAN. Using this technique, large, conductive films can be made which are sufficiently robust to allow intact lift-off and transfer of the films from one substrate to another. Such films are chemically inert, but can be photolithographically patterned and etched with an oxygen plasma.

International Nuclear Information System (INIS)

The spin relaxation processes within the pyrochlore Ho_2Ru_2O_7 have been investigated by neutron scattering and bulk property techniques. A single-ion process, that is thermally activated, dominates the spin-spin relaxation spectrum above 2 K. Assuming Arrhenius behaviour, we found an activation energy #DELTA# = (329 #+-# 6) K and characteristic relaxation time #tau#_0 (5.2 #+-# 0.3) x 10"-"1"2 s in the paramagnetic state, akin to those found in the spin ice, Ho_2Ti_2O_7. Atlow temperature (T<95 K) the activation energy lowers and below 20 K the entropy and ac susceptibility are similar to that observed in other spin ice compounds within a 10 kOe field.

Science.gov (United States)

Apparent evolution of relativistic flows as traced by radio emission results from a combination of several factors related to propagation of relativistic blobs or shocks, velocity, density and pressure stratification of the underlying flow, plasma instability and (possibly also) phase and time travel effect. This combination can create an intricate and chaotic patterns of the observed morphological changes in radio emission, which complicates the analysis and interpretation of kinematic and physical properties of the jet plasma. Recent studies have indicated that slow and quasi-stationary patterns in jets are most likely formed by plasma instabilities while faster, superluminally moving patterns are related to highly relativistic plasma condensations produced by the nuclear flares. Some of the stationary patterns may also be related to recollimation shocks or locations where strong non-thermal continuum is produced in jets. Similarities and ...

Energy Technology Data Exchange (ETDEWEB)

This renewal request for DOE grant DE-FG02-86ER45238, is dedicated to providing a complete thermodynamic profile of solids fluids, and fluid mixtures, over a wide range of temperatures and pressures. We are partially motivated by technological interest in detonation, combustion, superhard high pressure materials, and high temperature superconductors, which are important components of interest of various DOE laboratories. Our work on fluids and solids, composed of simple molecules, involves the determination of structures, phase transitions, pressure-volume relations, phonon, vibron, and libron modes of excitation, sound velocities, specific heats, thermal expansion, virial coefficients, sublimation energies, and orientational translational, and magnetic correlations. We hope that the study of these systems under extreme thermodynamic conditions will lead to exotic new materials of value, as well as enhanced fundamental understanding.

British Library Electronic Table of Contents (United Kingdom)

Abstract A one step method was used to prepare stable aqueous nanocomposite dispersions based on cellulose whiskers extracted from the rachis of the date palm tree and a poly(styrene co 2 ethyl hexylacrylate) copolymer via miniemulsion polymerization. A reactive silane, i.e., methacryloxypropyl triethoxysilane was added to stabilize the dispersion and favor the anchoring of the whiskers on polymer particles. Dynamic light scattering was used to study the effect of the silane and whiskers contents on the average particle size of the polymer. Nanocomposites materials were prepared from these dispersions using a casting/evaporation method. The effect of the silane and whiskers contents on the thermal and mechanical properties were studied using differential scanning calorimetry and dynamic me...

Energy Technology Data Exchange (ETDEWEB)

Energy International is developing a technology that will create a staged formulation with the first coal form (Mulled Coal) that can be stored, transported, and pumped. Just prior to combustion, the Mulled Coal (MC) would be modified to provide the properties needed for proper atomization. This concept is an alternative to the expensive and energy intensive thermal drying processing of fine coal wet cakes. The material is suitable for both direct feed use in conventional and fluid bed combustors as well as on-site conversion to combustible slurries. By maintaining the coal form relatively close to the feed wet cake, only minor processing with low additive levels and low energy blending needed at the point of production. Its conversion to slurry or other use-feed form is made near the time of use and thus the requirements for stability, climatic control, and other storage, transport, and handling requirements are much less severe.

British Library Electronic Table of Contents (United Kingdom)

The versatile electrospinning technique was used to successfully align and disperse multiwalled carbon nanotubes (MWCNT) in nylon 6,6 matrix to obtain composite fibers. The morphology of the composite fibers and the dispersion of the CNTs within the fibers were analyzed using scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. TEM analysis revealed that the CNTs were well-dispersed, separated and aligned along the fiber axis. The thermal and mechanical properties of the composite fibers were characterized as a function of weight fraction of the CNTs. Incorporation of the CNTs in the fibers resulted in an increase in glass-transition temperature (Tg) by 7degreeC, indicating that the addition of CNTs has restricted the mobility of the polymer chains a...

International Nuclear Information System (INIS)

DZ4 substrates were coated with NiCoCrAlY by plasma spray and subsequently treated by high current pulsed electron beams(HCPEB) of different parameters. The surface microstructure, phase structure and high temperature oxidation resistance were studied. It has been shown that as a result of the HCPEB treatment the loose and rough structure remelted and the surface became smooth. Smooth microregion, craters and cracks appeared on the surface. The ?' phase manifolded and there was no visible thermal stress. The oxidation test at 900 degree C for 100 h showed that a more compact and successive ?-Al_2O_3 scale was formed on the surface of the samples after HCPEB irradiation, which improved the oxidation resistance of the NiCoCrAlY coatings obviously. (authors)

Energy Technology Data Exchange (ETDEWEB)

The author explains current developments in high voltage cable technology and subsequently describes problems inherent in its application, from the users viewpoint, in municipal electricity supply. The planning of a high voltage cable network and the selection of a specific type of cable are not only dependent on the typical properties of various cables but to a major degree also on the feasible laying technique, the power transmitted, the costs, the stellation treatment of the high voltage network, the acceptance requirement, the inductive influence from telecommunication cable, thermal influences from the environment, eventual safeguards from mechanical and chemical damage to the network, frequency of failure and surveillance and breakdown location. In conclusion, the author portrays potential developments in the fields of high and maximum voltage cable from the perspectives of today.

British Library Electronic Table of Contents (United Kingdom)

Plasma polymerization of aniline is carried out in a radiofrequency plasma reactor and the effect of polymerization time is examined in the structural, optical and optoelectronic properties of deposited films. Conjugated structures of polyaniline like films are obtained with unique and broad optical absorption band in the ultraviolet and entire visible region. The width of the absorption band increases and hence the optical band gap decreases with polymerization time. The optical constants are extracted by Swanepoel method and the optical dispersion parameters are determined by employing the Wemple-DiDomenico single oscillator model. The films exhibit similar thermal stability in air and argon atmosphere in the region of interest for optoelectronic applications. The photoluminescence study...

British Library Electronic Table of Contents (United Kingdom)

Abstract:- In recent years, the study of polymer/clay nanocomposites has attracted major research and commercial interests due to their superior mechanical and thermal properties to those of the neat polymers. Numerical modelling is an advantageous approach to understand the material behaviour. In this work a symmetric two dimensional finite element model is developed to simulate the fully exfoliated Polymer/Clay nanocomposite behaviour and evaluate its- before stress stress-strain curve. The Nylon 66/Clay in this study has a nonlinear elastic behaviour. The influence of volume fraction and aspect ratio of clay platelet (defined as the ratio of the particle length to the particle thickness) on the tensile behaviour of exfoliated Nylon 66/clay nanocomposite is investigated with the aid of n...

International Nuclear Information System (INIS)

We develop a large scale parallel viscous-elastic analysis program incorporating a mesoscopic self-consistent model developed by Laws. In the model, macroscopic elastic constants are treated as variables depending on the shape and statistical properties of pre-existing microscopic pores and change due to neutron irradiation. We apply this program to the visco-elastic analysis of nuclear graphite structures under neutron irradiation environment in High Temperature Gas-cooled Reactor (HTGR), as an example problem. Furthermore the calculated results by this parallel computational program are compared with those by one of commercial finite element analysis codes, FINAS, for validating elastic and thermal stress analysis function. (author)

Energy Technology Data Exchange (ETDEWEB)

It is planned to bulk-heat a unit cell of a fusion reactor solid-breeder blanket in a fission reactor to study thermo-mechanical and thermal-hydraulic properties of fusion blankets. This study investigates the neutronic feasibility of using the Power Burst Facility (PBF) for this purpose. Heating rates were calculated for a Li/sub 2/O experiment placed in the PBF test space. The ANISN code and a 56-group coupled neutron-gamma library based on FLUNG and VITAMIN C were used to compute the heating rates. The results show that an average heating rate level of 1-3 W/cc can be produced in PBF with a local power profile that should be typical of a fusion blanket unit cell.

International Nuclear Information System (INIS)

Full text: Institute for Nuclear Research, Pitesti-Mioveni, Romania in direct cooperation with the National Institute for Laser, Plasma and Radiation Physics, Magurele, Bucharest studied and prepared for coating more than 1000 tiles made of Inconel with 7-9 #mu#m of beryllium for nuclear fusion applications at JET, Culham, UK. The principles of manufacturing processes using thermal evaporation and plasma ignited in pure metal vapors as well as by Thermionic Vacuum Arc (TVA) method and the properties of the Ni and Be coatings are presented. The prepared beryllium layers were characterized by scanning electron microscopy, transmission electron microscopy, X-ray diffraction, X-ray photoelectron spectroscopy and atomic force microscopy. (authors)

Energy Technology Data Exchange (ETDEWEB)

The catalytically stabilised thermal combustion (CST) of lean hydrogen-air mixtures was investigated numerically in a turbulent channel flow configuration using a two-dimensional elliptic model with detailed heterogeneous and homogeneous chemical reactions. Comparison between turbulent and laminar cases having the same incoming mean properties shows that turbulence inhibits homogeneous ignition due to increased heat transport away from the near-wall layer. The peak root-mean-square temperature and species fluctuations are always located outside the extent of the homogeneous reaction zone indicating that thermochemical fluctuations have no significant influence on gaseous combustion. (author) 4 figs., 6 refs.

British Library Electronic Table of Contents (United Kingdom)

The residing fracture system and the prevailing in situ stresses have a significant impact on fluid flow and heat transfer in crystalline rocks. The long term response of fracture systems to changes in effective stresses, in particular the long term geo-mechanical effects of thermal stresses on reservoir characteristics is of particular interest to the geothermal industry.In this paper, a geothermal reservoir model is presented, in which a thermo-poroelastic finite element module is coupled to a fracture geomechanical module. This describes fracture closure as a function of effective stress and the changes in parameters, such as effective permeability, porosity and discrete fracture apertures. The novelty of this approach lies in its dynamic treatment of the characteristic properties of in...

Energy Technology Data Exchange (ETDEWEB)

Perylene bisimides (PBIs) represent an important class of organic n-type semiconductors exhibiting a relatively high electron affinity among large-band-gap materials. Herein synthesis and characterization of several unsymmetrical N-substituted PBI dyes is presented and the thermotropic behavior, which is strongly affected by the respective N-substituents was investigated. Two different series of highly soluble and fluorescent derivatives have been synthesized: (1) PBIs bearing swallow-tailed alkyl chains, different in size or (2) one swallow-tailed alkyl chain and one branched oligoethylenglycolether. Synthesis of these PBIs is generally feasible by two distinct divergent synthesis approaches. Thermotropic behavior was studied by DSC, POM and XRD measurements. Inherent {pi}-{pi} interactions between cofacially orientated perylene molecules and the elliptic shape of the molecule favor the ordering in columns and self-organized architectures. Among them hexagonal columnar CoIh ...

Energy Technology Data Exchange (ETDEWEB)

A discussion is given concerning the transformation in acid medium of curite into copper-, nickel- and cobalt-uranylphosphate. From chemical, differential thermal and thermogravimetric analyses, the crystal-chemical formula are calculated as: Cu(UO/sub 2//PO/sub 4/)/sub 2/.8H/sub 2/O, Ni(UO/sub 2//PO/sub 4/)/sub 2/.7H/sub 2/O and Co(UO/sub 2//PO/sub 4/)/sub 2/.7H/sub 2/O. The two last compounds crystallize in the triclinic system with space group P1 or P1(overscore) and the first one crystallizes in the tetragonal system with space group P4/nmm. The cell parameters are calculated. From solubility data, the solubility products are computed as 10sup(-12.8), 10sup(-9.5) and 10sup(-9.9) for the copper-, nickel- and colbalt-compound respectively. The electrokinetic properties of the three species are closely similar to those of natural meta-torbernite: the zeta-potential is negative and the point of zero charge be reached cannot in the pH-range 2 to ...

Science.gov (United States)

Mg-Al mixed oxides with Mg/Al molar ratios of 0.5--9.0 were obtained by thermal decomposition of precipitated hydrotalcite precursors. The effect of composition on structure and surface and catalytic properties was studied by combining several characterization methods with ethanol conversion reactions. The nature, density, and strength of surface basic sites depended on the Al content. The catalyst activity and selectivity of Mg-Al mixed oxides in ethanol conversion reactions depended on composition. The dehydrogenation of ethanol to acetaldehyde and the aldol condensation to n-butanol both involved the initial surface ethoxide formation on a Lewis acid-strong base pair. The dehydration of ethanol to ethylene, and the coupling and dehydration to diethyl ether increased with Al content, probably reflecting the density increase of both Al{sup 3+}-O{sup 2{minus}} pairs and low- and medium-strength basic sites. Pure Al{sub 2}O{sub 3} displayed the ...

Energy Technology Data Exchange (ETDEWEB)

The meeting was arranged into the following sessions: introductory; advanced ceramics and ceramic composites; ceramic and metal matrix composites; electronic materials and devices; acoustoelasticity, stress, and texture; composites-porosity, strength, and UT propagation; process modeling and monitoring; thermal wave physics; material properties, composites, surfaces, and interfaces; acoustic emission; ferromagnetic materials; new sensors; NDE reliability assessment; elastic wave scattering and propagation; image analysis, data storage, and signal processing; UT transducers; weldments and bonded materials; eddy current models; unified life cycle engineering; x rays, CT, and NMR; eddy current probes and instruments; acoustic microscopy imaging, and reconstruction; signal processing, measurement techniques, and systems; NDE applications of artificial intelligence; crack behavior influenced by history; inversion procedures for UT and EC; process ...

Science.gov (United States)

A new class of hybrid organic-inorganic materials, and methods of synthesis, that can be used as a proton exchange membrane in a direct methanol fuel cell. In contrast with Nafion.RTM. PEM materials, which have random sulfonation, the new class of materials have ordered sulfonation achieved through self-assembly of alternating polyimide segments of different molecular weights comprising, for example, highly sulfonated hydrophilic PDA-DASA polyimide segment alternating with an unsulfonated hydrophobic 6FDA-DAS polyimide segment. An inorganic phase, e.g., 0.5 5 wt % TEOS, can be incorporated in the sulfonated polyimide copolymer to further improve its properties. The new materials exhibit reduced swelling when exposed to water, increased thermal stability, and decreased O.sub.2 and H.sub.2 gas permeability, while retaining proton conductivities similar to Nafion.RTM.. These improved properties may allow direct methanol fuel ...

Energy Technology Data Exchange (ETDEWEB)

Polycarbonate (PC), a non-crystalline resin, and polybutylene terephthalate (PBT), a crystalline resin, can be achieved by means of alloying of improving such various properties as chemical resistance, heat and impact resistance, and formability. This paper describes its manufacturing methods, properties, and market trends. A PC/PBT alloy improves the chemical resistance if the PBT composition ratio is high, but reduces thermal deformation temperature and impact strength. It is regarded adequate, therefore, that the PBT component ratio is set to 20% to 30%. The impact strength is improved by adding elastomer as a third component. The national production amount in 1992 was 4,800 tons a year; price per kilogram is 700 to 800 yen; and the main application is interior and exterior parts for automobiles. While PP and urethane are often used for interior and exterior automotive parts, there is a high possibility of transferring ...

Energy Technology Data Exchange (ETDEWEB)

Quasi-carbon fibers (QCFs) were prepared from Polyacrylonitrile (PAN) precursor by pyrolysis in the temperature range from 400{degrees}C to 950{degrees}C. The QCF-reinforced composites were fabricated by impregnating the QCFs with the PAN resin. The microstructural changes of both QCFs and their composites were characterized by the X-ray diffraction method. The stacking size and the crystallinity of the QCFs increased with the increasing heat treatment temperature (HTT). The crystallinity of the PAN matrix in a composite was also affected by various QCFs. DSC data indicated that thermal reaction mechanism of the composite could be altered due to the interaction between the fiber and the matrix. DMTA studies showed that good adhesion existed at the interface of the QCF-reinforced composites containing lower HTT fibers. The modulus magnitudes of QCFs and their composites increased with the QCF pyrolysis temperature. Although the QCFs exhibited a decreasing trend in ...

Energy Technology Data Exchange (ETDEWEB)

In the present paper, the chemical composition of passive films formed on both phases of two types of duplex stainless steels (UNS S31803 and UNS S32304) is determined at the micro-scale using Auger electron spectroscopy (AES). Samples were either mechanically polished (down to diamond pastes) or electrochemically etched in acidic solutions. The micro-electrochemical behavior of samples was then determined in sodium chloride media by means of the electrochemical micro-cell technique (capillary diameters of 30 {mu}m). The results obtained were analyzed considering the passive film chemical composition. Quantitative relationships between electrochemical parameters and the distribution of chromium and iron in the oxide layer were found. Due to differences in mechanical properties between ferrite and austenite, a heterogeneous stress distribution is generated in both phases. A method based on thermal-mechanical simulation was used to quantify ...

Energy Technology Data Exchange (ETDEWEB)

The influence of high energy electron (23 MeV) irradiation on the electrical characteristics of p-channel polysilicon thin film transistors (PSTFTs) was studied. The channel 220 nm thick LPCVD (low pressure chemical vapor deposition) deposited polysilicon layer was phosphorus doped by ion implantation. A 45 nm thick, thermally grown, SiO{sub 2} layer served as gate dielectric. A self-alignment technology for boron doping of the source and drain regions was used. 200 nm thick polysilicon film was deposited as a gate electrode. The obtained p-channel PSTFTs were irradiated with different high energy electron doses. Leakage currents through the gate oxide and transfer characteristics of the transistors were measured. A software model describing the field enhancement and the non-uniform current distribution at textured polysilicon/oxide interface was developed. In order to assess the irradiation-stimulated changes of gate oxide parameters the gate oxide tunneling ...

Energy Technology Data Exchange (ETDEWEB)

A highly efficient integrated energy conversion system is built based on a methane catalytic decomposition reactor (MCDR) together with a direct carbon fuel cell (DCFC) and an internal reforming solid oxide fuel cell (IRSOFC). In the MCDR, methane is decomposed to pure carbon and hydrogen. Carbon is used as the fuel of DCFC to generate power and produce pure carbon dioxide. The hydrogen and unconverted methane are used as the fuel in the IRSOFC. A gas turbine cycle is also used to produce more power output from the thermal energy generated in the IRSOFC. The output performance and efficiency of both the DCFC and IRSOFC are investigated and compared by development of exact models of them. It is found that this system has a unique loading flexibility due to the good high-loading property of DCFC and the good low loading property of IRSOFC. The effects of temperature, pressure, current densities, and methane conversion on the ...

International Nuclear Information System (INIS)

Brittleness and poor low-temperature thermal conductivity of A-15 compounds remain the major obstacles preventing the effective use of these superconductors in large-scale engineering applications. In order to circumvent these difficulties, a new type of ductile superconducting filamentary alloy has been developed recently by a simple metallurgical process which consists of melting the constituent elements and subsequent cold working and appropriate heat treatment. These superconducting materials are essentially Cu-base alloys containing a few percent of A-15 phase such as Nb_3Sn or V_3Ga which is in the form of fine filaments embedded in the Cu matrix. The emphasis of this work is on the formation of the A-15 phase in the Cu-base alloys and its correlation with superconducting properties such as transition temperature and critical current density. The formation of Nb_3Sn, Nb_3Al, V_3Si, and V_3Ga will serve as examples to illustrate the ...

Energy Technology Data Exchange (ETDEWEB)

Thermal, electrical, and electrochemical properties were investigated for the (100-x)(0.6Li{sub 2}S{center{underscore}dot}0.4SiS{sub 2}){center{underscore}dot}xLi{sub 4}SiO{sub 4} oxysulfide glasses. The glass with x = 5 exhibited high electrical conductivity of about 10{sup {minus}3} S cm{sup {minus}1} at room temperature, high glass stability against crystallization, and good chemical stability in contact with Li metal. Cyclic voltammetry also suggested that this glass has a wide electrochemical window of more than 10 V. On the other hand, further addition of Li{sub 4}SiO{sub 4} up to 20 mol% lowered the conductivity, glass stability against crystallization, and electrochemical stability for the oxysulfide glasses.

Energy Technology Data Exchange (ETDEWEB)

The changes in the electrical and structural properties of metal-silicide films caused by ion implantation and subsequent thermal annealing have been investigated. Epitaxial silicide films such as those of CoSi/sub 2/, NiSi/sub 2/ and Pd/sub 2/Si grown on Si(111) substrates were implanted with Ar ions and annealed in a vacuum furnace at temperatures ranging from 200 to 800/sup 0/C. Rutherford backscattering and channeling techniques and the four-point probe method were used to measure the crystalline quality and the sheet resistance of the films, respectively. It was found that the sheet resistances of CoSi/sub 2/, NiSi/sub 2/ and Pd/sub 2/Si films were increased by factors of 70, 6, and 3, respectively, by implantation to a dose of 1 x 10/sup 16/ Ar-ions/cm/sup 2/, but that they were almost restored by subsequent annealing to the values before implantation. A phase transformation from Pd/sub 2/Si to PdSi was also observed in the ...

International Nuclear Information System (INIS)

Volatile compounds produced in flexible food packaging materials (LDPE, EVAc, PET/PE/EVOH/PE) during electron beam irradiation were isolated by purge and trap technique and identified by combined gas chromatography-mass spectrometry (GC/MS), after thermal desorption and concentration. For comparison purposes non-irradiated films were also studied. Film samples were irradiated at low (5 kGy, corresponding to cold pasteurization), intermediate (20 kGy, corresponding to cold sterilization) and high (100 kGy) doses. It was observed that a number of volatile compounds are produced after irradiation in all cases. Furthermore the amounts of all volatile compounds increase with increasing irradiation dose. Both primary (methyl-derivatives etc.) as well as secondary i.e. oxidation products (ketones, aldehydes, alcohols, carboxylic acids etc.) are produced upon irradiation. These products may affect organoleptic properties and thus shelf-life of ...

International Nuclear Information System (INIS)

Low molecular weight epoxy resin based on diglycidyl ether of bisphenol A was synthesized and mixed at constant percentages with natural rubber. The rubber epoxy system was cured with various types of curing agents such as ethylene diamine, maleic anhydride as well as the prepared resole phenol formaldehyde. A study of the photo-induced crosslinking of the prepared elastic adhesives and film samples was carried out by exposure to ultraviolet lamp (300 w) for 2 weeks at 20 deg. C. Samples containing ethylene diamine were cured at 25 + - 1 deg. C. for 24 h while samples containing maleic anhydride or resole phenol formaldehyde resins were thermally cured at 150-170 deg. C. for 10 min. Cured adhesive compositions were tested mechanically and physically and evaluated as wood adhesives. While hardness, chemical resistance as well as heat stability of the prepared cured film sample were investigated. The obtained data indicate that the highest epoxy resin content and the ...

Energy Technology Data Exchange (ETDEWEB)

The paper presents the preparation, X-ray powder diffraction data as well as some magnetic and spectroscopic properties of a new uranium(III) complex bromide of the formula NH{sub 4}UBr{sub 4}.1.5CH{sub 3}CN.6H{sub 2}O. The compound crystallizes in the monoclinic system with a=11.877 A, b=6.385 A, c=6.815 A, {beta}=101.29deg and Z=2. In the 60-240 K range it follows the Curie-Weiss law with {theta}=-37.24 K and {mu}{sub eff}=3.20 B.M. The IR and UV-VIS absorption spectra were recorded in the 80-4000 cm{sup -1} and 4000-26000 cm{sup -1} spectral ranges respectively. Thermal decomposition at a non-static high vacuum enabled the conversion of the compound into pure and anhydrous UBr{sub 3}. (orig.).

International Nuclear Information System (INIS)

The A-15 compounds are known to favor the occurrence of high temperature superconductivity (transition temperature T/sub c/ > 15K). The origin of superconductivity in these metals is a subject of much controversy and importance. A useful approach to this problem is to study comparatively the superconducting and normal-state properties of the A-15 superconductors and their amorphous counterparts. Efforts along these lines have yielded some insight into the mechanisms responsible for high temperature superconductivity. It is interesting to note that most high-T/sub c/ A-15 compounds contain one glass-forming element such as Ge, Si or Al and are thus conducive to the formation of a non-crystalline phase. The amorphous (or higher disordered) state of the A-15 compounds can be achieved, for example, by one of the following techniques: (1) sputtering or co-evaporation onto substrates held at relatively low temperatures; (2) particle irradiation; and (3) ion-mixing. It ...

Energy Technology Data Exchange (ETDEWEB)

Thin, elastic foils of good resistance to the air exposure, patented as wound healing aids, were prepared by evaporation of a blend of lecithin (L) and sodium hyaluronan (H) taken under varying proportions. The contact angle for water, glycerol, formamide, ethylene glycol and diiodomethane, was determined for these foils. The contact angle was correlated against the H:L foil composition. For all liquids but formamide the highest contact angle was noted for the H:L = 2:1 (g g{sup -1}) ratio. The contact angles provided estimation of the work of adhesion. At the same L:H ratio the work of adhesion was the lowest. It was suggested that lecithin cross-linked hyaluronan. Since the work of adhesion of the studied liquids was similar to that of diiodomethane, it could be concluded that almost all functional groups on the foil surface were completely blocked. Perhaps, at H:L = 2:1 (g g{sup -1}) a stoichiometric complex of hyaluronic acid with lecithin was formed, and polar functional groups ...

Science.gov (United States)

Lead-free piezoelectric ceramics (1-x)K0.5Na0.5NbO3-xAgSbO3+0.75 mol % MnO2 were prepared by a conventional solid-state sintering technique, and the piezoelectric and dielectric properties of the ceramics were studied. The results of x-ray diffraction suggest that AgSbO3 diffuses into the K0.5Na0.5NbO3 lattices to form a new solid solution with a single-phase orthorhombic perovskite structure. After the addition of AgSbO3, the paraelectric cubic-ferroelectric tetragonal phase transition temperature (TC) and the ferroelectric tetragonal-ferroelectric orthorhombic phase transition temperature (TO-T) decrease, and the ceramics become ``softened,'' resulting in significant improvements in the ferroelectric and piezoelectric properties. The ceramics with x=0.03-0.10 exhibit excellent piezoelectric properties: d33=130-216 pC/N, kp=0.44-0.51, and kt=0.40-0.52. The ceramics also exhibit a good thermal stability ...

International Nuclear Information System (INIS)

Particulate ceramic composites that were composed of a combustion-synthesized #beta#'-SiAlON matrix and dispersed MoSi_2 particles were hot pressed at 1,600 C in a nitrogen atmosphere. The physical and mechanical properties of the composites that contained 15, 30, and 45 vol% MoSi_2 were evaluated. The average four-point bend strength, fracture toughness, and Vickers hardness of the composites were in the ranges of 500--600 MPa, 3--4 MPa#centre dot#m"1"/"2, and 11--13 GPa, respectively. The measured mechanical strength and hardness were very similar to the values that were predicted from the rule of mixtures. The fracture toughness of the combustion-synthesized #beta#'-SiAlON (2.5 MPa#centre dot#m"1"/"2) was apparently enhanced by the MoSi_2 particles that were added. The increase in the fracture toughness was predominantly attributed to the residual thermal stress that was induced by the thermal expansion mismatch between ...

Energy Technology Data Exchange (ETDEWEB)

The effect of thermal pretreatment in N[sub 2] up to 723 K and the activation treatments in H[sub 2] and an inert atmosphere on the properties of Ni and Co activated-charcoal-supported catalysts were studied. Catalysts were characterized by means of N[sub 2] adsorption at 77 K, H[sub 2] chemisorption at room temperature, thermogravimetric analysis (TGA), X-ray diffraction (XRD), and transmission electron microscopy (TEM). The catalysts' activity and selectivity for acetone hydrogenation to 2-propanol under unusual and severe conditions (473 K and high overall acetone conversion) were also measured. TGA and XRD evidence was found for the charcoal-support-promoted NiO and CoO reduction to the metallic states when the catalysts were subjected to an inert atmosphere above 723 K caused a loss of acetone hydrogenation activity (calculated on a metal load basis) for both the Ni and Co activated-charcoal-supported catalysts, with respect to ...

Energy Technology Data Exchange (ETDEWEB)

Epitaxial cobalt disilicide (CoSi{sub 2}) layers are grown on n-Si{sub 0.83}Ge{sub 0.17}/n-Si(001) using a sacrificial Si capping layer at the growth temperature T{sub s}=650 deg. C by reactive chemical vapor deposition using cyclopentadienyl dicarbonyl cobalt (Co({eta}{sup 5}-C{sub 5}H{sub 5})(CO){sub 2}). Structural and electrical properties of epi-CoSi{sub 2}/Si{sub 0.83}Ge{sub 0.17}/Si(001) were measured by transmission electron microscopy, X-ray diffraction, Auger electron spectroscopy and sheet resistance measurement as a function of annealing temperature. The combined results showed that the epitaxial CoSi{sub 2} phase by the reaction of Co with the Si capping layer was formed in the as-grown layers. Rapid thermal anneals for the investigation of thermal stability of the as-grown layers showed good thermal stability of the epitaxial CoSi{sub 2} layers with the low sheet resistance value as low as ...

International Nuclear Information System (INIS)

As part of a study into the properties of ferroelectric single crystals at nanoscale dimensions, the effects that focused ion beam (FIB) processing can have, in terms of structural damage and ion implantation, on perovskite oxide materials has been examined, and a post-processing procedure developed to remove such effects. Single crystal material of the perovskite ferroelectric barium titanate (BaTiO_3) has been patterned into thin film lamellae structures using a FIB microscope. Previous work had shown that FIB patterning induced gallium impregnation and associated creation of amorphous layers in a surface region of the single crystal material some 20 nm thick, but that both recrystallization and expulsion of gallium could be achieved through thermal annealing in air. Here we confirm this observation, but find that thermally induced gallium expulsion is associated with the formation of gallium-rich platelets on the surface ...

CERN Document Server

The composition of the lower mantle can be investigated by examining densities and seismic velocities of compositional models as functions of depth. In order to do this, it is necessary to know the volumes and thermoelastic properties of the compositional constituents under lower mantle conditions. We determined the thermal equation of state (EoS) of MgSiO3 perovskite using the non-empirical VIB interatomic potential with molecular dynamics simulations at pressures and temperatures of the lower mantle. We fit our P-V-T results to a thermal EoS of the form P(V,T) = P0(V,T0) + Delta Pth(T), where T0 = 300 K and P0 is the isothermal Universal EoS. The thermal pressure Delta Pth can be represented by a linear relationship Delta Pth = a + b T. We find V0 = 165.40 A^3, KT0 = 273 GPa, K'T0 = 3.86, a = -1.99 GPa, and b = 0.00664 GPa/K for pressures of 0-140 GPa and temperatures of 300-3000 K. By fixing V0 to ...

Science.gov (United States)

A comparative analysis between conventional passive twin tube dampers and skyhook-controlled magneto-rheological fluid (MRF) dampers for motorcycle front suspensions is provided, based on single axis testing in a damper test rig and suspension performance testing in road trials. Performance motorcycles, while boasting extremely light suspension components and competition-ready performance, have an inherent weakness in comfort, as the suspension systems are designed primarily for racing purposes. Front suspension acceleration and shock loading transmit directly through the front suspension triple clamp into the rider's arms and shoulders, causing rapid fatigue in shoulder muscles. Magneto-rheological fluid dampers and skyhook control systems offer an alternative to conventional sport motorcycle suspensions - both performance and comfort can be combined in the same package. Prototype MRF dampers designed and manufactured specifically for this ...

Energy Technology Data Exchange (ETDEWEB)

Abstract not provided

Science.gov (United States)

Not Available

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

... thermal power plants thermal reactors water cooled reactors WATER

Energy Technology Data Exchange (ETDEWEB)

A 100 kW thermal input Two-Stage Gasifier was built at the University of Denmark (DTU). The gasifier consists of an externally heated pyrolysis unit, a down-draft char gasifier, a gas cleaning system and an internal-combustion engine. Between the summer of 1996 and the summer of 1998, 11 tests were made with the gasifier. The gasifier had a total operating time of 278 hours (excluding warming up). The fuel was mainly wood chips, but also briquettes has been used. Four of the tests lasted 50-70 hours, and stable conditions were reached. All the tests were completed without technical problems. The particle sizes and amounts were investigated. The amount of particles depended on the amount of steam led to the gasifier. More than 99% of the particles after the cyclone were soot. The size of the soot particles was mainly between 0.2-0.5 {mu}m. Under normal conditions (biomass:steam = 1:1 (dry mass basis)), the particle load was about 300 mg/Nm{sup 3}. With biomass:steam ...

Energy Technology Data Exchange (ETDEWEB)

The particle surface of Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} was modified by AlF{sub 3} as a new coating material to improve the electrochemical properties in the high cutoff voltage of 4.5 V. The AlF{sub 3}-coated Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} showed no difference in the bulk structure compared with the pristine one and the uniform AlF{sub 3} coating layers whose thickness is of about 10 nm covered Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles, as confirmed by a transmission electron microscopy. The AlF{sub 3} coating on Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2} particles improved the overall electrochemical properties such as the cyclability, rate capability and thermal stability compared with those of the pristine Li[Ni{sub 1/3}Co{sub 1/3}Mn{sub 1/3}]O{sub 2}. Such enhancements were attributed to the presence of the stable AlF{sub 3} layer which acts as the interfacial stabilizer on ...

Energy Technology Data Exchange (ETDEWEB)

Diamond-like carbon thin films for tribological applications were deposited by d.c.-magnetron sputtering of a graphite target in a pure argon atmosphere or in a reactive hydrogen or methane atmosphere at pressures between 0.1 and 1 Pa in a graded constitution to improve adhesion and reduce residual stress. The temperature of the metallic, carbon- and ceramic-like substrates was below 100 C. The mechanical, thermal, electronic and optical properties of the carbon thin films show a significant dependence on the ion energy. Below 220 eV, strongly adherent black conductive films with hardness values up to 2000 HV0.05 were obtained. Hard and superhard diamond-like carbon thin films were deposited in an energy range between 220 and 370 eV with hardness values up to 4000 HV0.05. They are insulating, optically transparent and show a high degree of hardness combined with high compressive stress in the order of 4 GPa as well as a low adhesion, which ...

Energy Technology Data Exchange (ETDEWEB)

The effect of powder particle sizes of n- and p-Bi2Te3 on the thermoelectric properties has been studied. The powder was formed from the each ingot and sieve into <63, 63-90 and 90-150{mu}m for p-type, and <355 and >355 {mu}m for n-type. Those powders are pressed followed by CIP, then sinterd at 773K for S. Effects of CIP on the densities were not so large such as 1-4% depending on the powder sizes. The Setback coefficients and electric conductivities for p-type were 110{mu}V/K and 0.8{times}10{sup 2}ohm{sup -1}m{sup -1} at 333K, while 18O{mu}V/K and 2.0{times}10{sup 4}ohm{sup -1}m{sup -l} for n-type, respectively. The thermal conductivity for n-type was 0.7W/mK leading to the figure of merit of 2.1{times}10{sup -3}(/K). The hybrid texture of the suitable amount of smaller and larger grains has a possibility of an improvement for thermoelectric properties. 10 refs., 5 figs., 5 tabs.

Science.gov (United States)

An electric power generating apparatus is described, including: a solar collector; a primary thermal loop including primary thermal fluid; a cavity receiver to receive reflected solar energy from the solar reflector, convert the solar energy into thermal energy, and transmit the thermal energy to the primary thermal fluid by heating the primary thermal fluid not to exceed a given temperature, the given temperature being substantially equal to 700 F; a Stirling engine receiving the primary thermal fluid heated by the cavity receiver, including means to generate mechanical power and means to generate electrical power from the means to generate mechanical power.

Science.gov (United States)

... Descriptors : *COMBUSTIBLE CARTRIDGE CASES, STYPHNATES, PHYSICAL PROPERTIES, TENSILE PROPERTIES, PRIMERS ...

International Nuclear Information System (INIS)

This report summarizes the findings of a five-month LDRD project funded through Sandia's NTM Investment Area. The project was aimed at providing the foundation for the development of advanced functional materials through the application of ultrathin coatings of microporous or mesoporous materials onto the surface of substrates such as silicon wafers. Prior art teaches that layers of microporous materials such as zeolites may be applied as, e.g., sensor platforms or gas separation membranes. These layers, however, are typically several microns to several hundred microns thick. For many potential applications, vast improvements in the response of a device could be realized if the thickness of the porous layer were reduced to tens of nanometers. However, a basic understanding of how to synthesize or fabricate such ultra-thin layers is lacking. This report describes traditional and novel approaches to the growth of layers of microporous materials on silicon wafers. The novel approaches ...

Energy Technology Data Exchange (ETDEWEB)

Experimental and numerical investigations were performed for the laminar burning velocity and the flame structure of laminar premixed CH{sub 4}/O{sub 2}/CO{sub 2} flames. Measurements of the laminar burning velocity were conducted by using a flame cone angle method for a circular nozzle burner. Numerical simulation was performed using one-dimensional plane flame code including radiation heat loss with an optically thin model. It was shown that the laminar burning velocity decrease with CO{sub 2} addition even though the adiabatic flame temperature is the same as that for CH{sub 4}/Air flames. The radiation heat loss is significant for the CH{sub 4}/O{sub 2}/CO{sub 2}, flames, and the flame temperature and laminar burning velocity decreases when the radiation heat loss is considered. Effects of thermal properties, radiation, and chemical reaction on the determination of the laminar burning velocity of CH{sub 4}/O{sub 2}/CO{sub 2} flames were ...

International Nuclear Information System (INIS)

The properties of the triplet of low-lying states in "1"0"1Mo have been studied through spectroscopy of the #gamma# radation following thermal neutron capture in "1"0"0Mo and #beta#-decay of "1"0"1Nb and through a measurement of the proton angular distributions in the "1"0"0Mo(d, p) reaction with 14 MeV deuteron energy. The half-lives of the 13.5 keV state and the 57.0 keV 5/2"+ state have been measured as 226(7) and 133(7) ns, respectively. These values and the quadrupole/dipole mixing ratios of the 13.5 keV and 43.5 keV transitions yield spin and parity 3/2"+ for the 13.5 keV level. The E2 components in the 13.5 (3/2"+#->#1/2"+) and 43.5 keV (5/2"+#->#3/2"+) transitions are #<=# 8x10"-"4 and 54(9)%, respectively. The possibility of an additional state near to the 57.0 keV level is discussed. IBFM/PTQM calculations, taking into consideration the transitional character of the "1"0"0Mo boson core, account for the ...

International Nuclear Information System (INIS)

In order to study the two-phase natural circulation and flow termination during a small break loss of coolant accident in LWR, simulation experiments have been performed. Based on the two-phase flow scaling criteria developed under this program, an adiabatic hot leg U-bend simulation loop using nitrogen gas and water and a Freon 113 boiling and condensation loop were built. The nitrogen-water system has been used to isolate key hydrodynamic phenomena from heat transfer problems, whereas the Freon loop has been used to study the effect of phase changes and fluid properties. Various tests were carried out to establish the basic mechanism of the flow termination and reestablishment as well as to obtain essential information on scale effects of parameters such as the loop frictional resistance, thermal center, U-bend curvature and inlet geometry. In addition to the above experimental study, a preliminary modeling study has been carried out for ...

Energy Technology Data Exchange (ETDEWEB)

Silica and bridged polysilsesquioxane aerogels are low-density materials that are attractive for applications such as thermal insulation, porous separation media or catalyst supports, adsorbents, and cometary dust capture agents. However, aerogels are notoriously weak and brittle making it difficult to handle and machine monoliths into desired forms. This complication prevents the development of many applications that would otherwise benefit from the use of the low-density materials. Here, we will describe our efforts to chemically modify and mechanically enhance silica-based aerogels using chemical vapor techniques without sacrificing their characteristic low densities. Monolithic silica and organic-bridged polysilsesquioxane aerogels were prepared by sol-gel polymerization of the respective methoxysilane monomers followed by supercritical carbon dioxide drying of the gels. Then the gels were reactively modified with silylating agents to demonstrate the viability ...