Science.gov (United States)

The catalytic effects of copper-aluminium-magnesium oxides in the oxidative coupling of phenylethyne is described. The importance of surface properties as a redox site are discussed.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

Energy Technology Data Exchange (ETDEWEB)

The aim of this study as to determine the mechanisms involved in using ammonium fluoborate as a reducing atmosphere when preheating a high magnesium content aluminium alloy. Rutherford Backscattering (RBS) has been the major technique used in the analysis of samples, it revealed significant reduction in both the diffusion of magnesium to the surface and the calculated oxide thickness in the presence of NH{sub 4}BF{sub 4}. At temperatures above 500 deg C in air, SEM images revealed depressions and voids due to incipient melting at various stages, around the grain boundaries. Grain boundaries effectively acted as pipes aiding the diffusion of magnesium to the surface. These results have been verified through compositional analysis with both RBS and auger electron spectroscopy (AES). Results from NH{sub 4}BF{sub 4} atmosphere preheat conditions showed significant improvements. It was verified ...

International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion solutions upon the coatings formation was recorded. It is ...

Energy Technology Data Exchange (ETDEWEB)

Stearic acid gel is employed to study the phase evolution of MgTiO{sub 3} nanoparticles by thermal gravimetric analysis, X-ray diffraction, and Fourier transform infrared. During the preparation of stearic acid gel, tetrabutyl titanate easily absorbed moisture to hydrolyze into Ti(OH){sub 4} firstly, and then reacts with stearic acid and magnesium stearate to form magnesium-titanium oxide network polymer gel, meanwhile n-butanol is generated. When stearic acid gel is calcined in air, a series of oxidation and combustion reactions occur, meanwhile apparent heat is given off. The results show that a metastable intermediate phase Mg{sub 2}TiO{sub 4} is generated at 450 {sup o}C and nearly disappeared at 550 {sup o}C. Simultaneously, a new solid phase of MgTiO{sub 3} appears. The metastable intermediate phase Mg{sub 2}TiO{sub 4} is successfully identified in the current work.

International Nuclear Information System (INIS)

After being pre-plated a zinc layer, an amorphous Al-Mn alloy coating was applied onto the surface of AZ31B magnesium alloy with a bath of molten salts. Then the corrosion performance of the coated magnesium alloy was examined in 3.5% NaCl solution by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS). The results showed that the single Zn layer was active in the test solution with a high corrosion rate while the Al-Mn alloy coating could effectively protect AZ31B magnesium alloy from corrosion in the solution. The high corrosion resistance of Al-Mn alloy coating was ascribed to an intact and stable passive film formed on the coating. The performances of the passive film on Al-Mn alloy were further investigated by Mott-Schottky curve and X-ray photoelectron spectroscopy (XPS) analysis. It was confirmed that the passive film exhibited n-type semiconducting behavior in 3.5% NaCl solution with a ...

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

Energy Technology Data Exchange (ETDEWEB)

Recent developments on plastic forming technology of magnesium alloys are presented. Attempts have been undergoing with an aim at forming magnesium alloy parts at lower temperatures. It is believed that fine microstructure magnesium alloys usually have much higher plasticity at lower temperatures and even room temperatures. Extrusion is a method to form magnesium profile products and tube products, which is also one of the effective ways to make fine microstructure magnesium alloys. Superplasticity forming is another method to form high plasticity magnesium alloys. Hot forming of magnesium sheet parts is an important process to form magnesium products. Some developments related to above issues are discussed in the present paper. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The cost of transporting biogas digestate can be decreased by reducing its water content. However, the digestate emits volatile compounds during drying. This study investigated the drying behaviour and the change of digestate composition. Drying took place in a hybrid solar/waste-heat dryer that used solar energy as well as waste heat from a combined heat and power unit (CHP) and the exhaust air of a microturbine. The experiment involved the use of 60 t of liquid digestate. Climatic conditions were measured inside and outside the drying hall. Dry matter (DM) and organic dry matter (ODM) were also measured on a daily basis. In addition, the energy consumption of waste and solar heat were recorded and related to the quantity of dried feedstock. The total nitrogen, ammonium, phosphate, potassium oxide, magnesium oxide and calcium oxide in the digestate were subjected to chemical analysis before and after ...

British Library Electronic Table of Contents (United Kingdom)

Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...

British Library Electronic Table of Contents (United Kingdom)

The electroless nickel plating/poly(dl-lactide-co-glycolide) composite coating (EN-plating/PLGA composite coating) was fabricated on the surface of the micro-arc oxidation (MAO) film of the magnesium alloy AZ81 to double control the corrosion and drug release in the hanks' solution. The EN-plating was fabricated on the MAO coating to improve the corrosion resistance by overlaying most pores and micro-cracks on the surface of the MAO film. Meanwhile, a double layered organic poly(dl-lactide-co-glycolide)/paclitaxel (PLGA/PTX) drug releasing coating with a top layered PLGA drug controlled releasing coating on EN plating was prepared to control the drug release rate by adjusting the different lactide: glycolide (LA:GA) ratio of PLGA. Scanning electron microscopy (SEM) and the X-ray powder dif...

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys show a high specific strength and are therefore increasingly used for light-weight constructions in transportation industry.{sup [1,2]} To predict the behaviour of the material under the influence of cyclic loading it is vital to understand the fatigue behaviour of magnesium alloys. Only when understood properly, it is possible to fully apply the potential weight reduction by using magnesium alloys. A very important aspect in fatigue of magnesium alloys is the influence of a corrosive media and elevated temperatures, of which both are relevant in automotive applications. These two factors tend to have deleterious effects on magnesium alloys and therefore also have to be considered in investigations on the fatigue behaviour of magnesium alloys. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

International Nuclear Information System (INIS)

Uranium-aluminum alloys with a significant enrichment of uranium with "2"3"3U or "2"3"5U serve as nuclear fuels in research reactors. The quality assurance of this fuel requires, among other things, precise knowledge that all trace metal constituents that affect neutron economy, fuel integrity, and fuel fabrication process parameters are well within the specification limits. Trace metal characterization of "2"3"5U-Al alloy has been carried out by atomic spectrometry. The trace metal constituents of interest are grouped into common metals (silver, boron, calcium, cadmium, cobalt, chromium, copper, iron, magnesium, manganese, molybdenum, sodium, nickel, lead, silicon, tin, titanium, vanadium, tungsten, and zinc) and lanthanides (cerium, dysprosium, europium, gadolinium, holminium, lutetium, samarium, and terbium). The elements yttrium and zirconium are grouped with the latter in view of the chemical separation procedure used. The alloy samples are dissolved in 6 M ...

Energy Technology Data Exchange (ETDEWEB)

Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal surfaces for the ...

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The extraction of magnesium by tributyl phosphate from KI solutions was investigated. With increasing KI and TBP concentrations, the extraction increased. The maximum extraction (82%) was attained at pH 4, and it did not decrease with a further pH increase. With decreasing pH, the extraction decreased because of HI extraction. The magnesium was extracted as the compound MgI/sub 2/ x 4TBP. Complexone III (at pH 3-4) does not affect the extraction of magnesium, which makes it possible to use it to mask other metals.

Energy Technology Data Exchange (ETDEWEB)

Two extruded magnesium alloys, AZ31 and AZ61 were selected to evaluate the influence of process parameters on the material forgeability. The processing parameters considered for forging magnesium alloys were: compression load in the range 55 KN to 60 KN and forging temperature, in the range of ambient temperature to 300 C. Uniaxial compression tests were conducted to establish the strain-temperature relationship. The influences of process parameters on the microstructure were also evaluated. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Measurements of the double-electron-capture process in which a positive ion of iodine becomes a negative ion in a single collision with a magnesium atom are reported between 20 and 90 keV. The cross section is comparable to that for the rare gases and not as large as might be expected from a two-valence-electron atom. This process is probably insignificant in the production of negative ion beams using a magnesium-vapor target.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are being increasingly utilized in a variety of fields as an alternative material to organic materials and aluminum alloys, owing to excellent properties. Those include low density, and excellent damping properties. When compared to organic materials, furthermore, Mg alloy excels at recyclability, heat radiation, and electromagnetic-shielding. Though most of magnesium alloy products are manufactured through die-casting and thixo-molding at present, the demand for the expanding of magnesium wrought alloy market is increasing. Taking full advantage of a drawing technique and applying it to the conventional extruded pipe, we have developed a new type of magnesium alloy pipe. The strength of the developed pipe is significantly higher than that of the conventional one, either extruded or die-casting. Some of the excellent properties were obtained from fundamental tests performed with the ...

International Nuclear Information System (INIS)

An experimental approach has been performed to ascertain the effectiveness of semi-solid strip casting using a horizontal twin roll caster. The demand for light-weight products with high strength has grown recently due to the rapid development of automobile and aircraft technology. One key to such development has been utilization of magnesium alloys, which can potentially reduce the total product weight. However, the problems of utilizing magnesium alloys are still mainly related to high manufacturing cost. One of the solutions to this problem is to develop magnesium casting-rolling technology in order to produce magnesium sheet products at competitive cost for commercial applications. In this experiment, magnesium alloy AZ31B was used to ascertain the effectiveness of semi-solid roll strip casting for producing magnesium alloy sheets. The temperature of the ...

Energy Technology Data Exchange (ETDEWEB)

Increase usage of magnesium components in the portable electronics industries has propelled considerable research interest on the development of magnesium forging. There have been some studies done in the area of sheet metal forming and forging of axis-symmetrical parts of magnesium alloys but there are very little work done on the plane strain backward extrusion of magnesium alloy. This paper deals with the analysis of plane strain extrusion of magnesium alloy, AZ31, using numerical modeling at different extrusion conditions of temperatures and friction coefficients. A commercially available finite element package, ANSYS/LSDYNA, was used in the finite element analysis. FE simulated results, material deformation, punch force and stress/strain distributions, were compared with actual experimental data. From the numerical analysis, a decrease in forging temperature from 300 C to 250 C ...

Energy Technology Data Exchange (ETDEWEB)

To improve the surface properties of magnesium alloy, a lining process using shot peening was carried out. The lining of magnesium alloy with metals such as titanium and nickel is useful in heightening the corrosion and wear properties for the components. In the shot peening experiment, the foil set on the magnesium workpiece is pelted with many shots at a high velocity. The foil is bonded to the surface of the workpiece due to plastic deformation induced by the collision of the shots. A pure aluminum foil is inserted between the hard foil and magnesium workpiece to assist the bonding. To heighten the bondability, the foil and workpiece are heated and the flow stresses of the metals are reduced. In this experiment, a centrifugal shot peening machine with an electrical heater was employed. The workpieces were commercially magnesium alloys AZ31B and AZ91D, and the foils were ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium cast parts as well as indirectly and hydrostatically extruded profiles were used in order to investigate the influence of different microstructures on the damping behaviour of magnesium AZ-alloys. Especially, hydrostatic extrusion leads to a significant grain refinement in the extruded profile compared to indirect extrusion. Strain dependent damping measurements were carried out at room temperature using alloys AZ31, AZ61 and AZ80. Damping was determined as the logarithmic decrement of free bending beam vibrations. The results of these measurements after indirect and hydrostatic extrusion are shown and discussed. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The effects of carbon inoculation by C{sub 2}Cl{sub 6} addition were investigated using commercial AZ31 magnesium alloy. The additions of C{sub 2}Cl{sub 6} to AZ31 magnesium alloy significantly reduce the grain size from 280 {mu}m to about 120 {mu}m and the tensile properties are also increased due to grain refinement. EPMA analysis shows that Al-C-O compounds are formed in the castings which are considered to function as nucleants. (orig.)

Science.gov (United States)

Increasing the Mg(2+) concentration results in a depression of succincoxidase-linked state 3

Energy Technology Data Exchange (ETDEWEB)

A new technique has been developed for improving corrosion resistance on magnesium alloys. Specimens of AZ31 magnesium alloy were dipped into molten salt of NaBF{sub 4} at 723 K for various times, and then cooled, rinsed with water, and dried in air. Corrosion resistance in the surface treated specimens was evaluated by salt immersion test using 1% NaCl solution as a time for occurring filiform corrosion. On an un-treated AZ31 alloy, the time for starting the filiform corrosion was about 1.2 ks, while on the surface treated specimen, the time was prolonged into about 1300 ks. Moreover, the surface treated specimen showed corrosion resistance in low pH solutions, such as 1% HNO{sub 3} and HCl solutions. (orig.)

UK PubMed Central (United Kingdom)

Hypocalcemia in the hypomagnesemic state in man is usually attributed to refractoriness of end-organs to the calcemic action of parathyroid hormone. We studied the responsiveness of end-organs to bovine...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A new interest in magnesium alloys has arisen since light-weight constructions have become more and more attractive. Products that are currently available are mostly cast, forged, and extruded. A cost-effective production of sheet metals will render new perspectives in the design of light-weight constructions. The development of new casting technologies like thin slab casting or strip casting with an in-line rolling process is expected to result in a shorter processing time featuring a high potential of saving energy, time, and cost. Particular attention is paid to the casting process parameters such as casting speed and solidification speed. This article deals with some aspects of a magnesium-adapted single-belt caster. Results of casting experiments and material examination are shown as well as some advices given concerning safety and handling of liquid magnesium. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Corrosion behavior of deposition coated specimens prepared by the technique proposed by the authors is investigated in salt immersion tests, and also those of pure magnesium, 3N, 4N and 6N grades, and magnesium alloys, AZ31 and AZ91E, are investigated for comparison. Inhomogeneous corrosion occurs in AZ31 and AZ91E alloys when buffered solutions with pH values of 6.5 and 9.0 including 1% NaCl and a conventional 3% NaCl solution are used for immersion tests, while 6N-Mg shows homogeneous corrosion in such solutions. Corrosion behavior of the deposition coated specimen resembles that of 6N-Mg. Purification process included in the deposition coating technique provides homogeneity in microstructural and electrochemical terms, which results in improving corrosion resistance. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the extrusion characteristics of magnesium alloy (AZ31), a computer simulation was attempted. Tensile properties of as-cast billet with different strain rates were incorporated into the simulation. The results showed a great change in distribution of stress and strain at near die region by the ram travel. It was found that the average grain size at longitudinal edge of the extruded sheet was smaller than that at center region, which might be attributed to recrystallization caused by severe plastic deformation. (orig.)

International Nuclear Information System (INIS)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

Energy Technology Data Exchange (ETDEWEB)

Polycrystalline Al2O3, magnesium aluminate spinel (MgAl2O4), MgO, Si3N4, and SiC were irradiated with various ions at 200-450 K, and microstructures were examined following irradiation using cross-section TEM. Amorphization was not observed in any of the irradiated oxide ceramics, despsite damage energy densities up to {similar_to}7 keV/atom (70 displacements per atom). On the other hand, SiC readily amorphized after damage levels of {similar_to}0.4 dpa at room temperature (RT). Si3N4 exhibited intermediate behavior; irradiation with Fe{sup 2+} ions at RT produced amorphization in the implanted ion region after damage levels of {similar_to}1 dpa. However, irradiated regions outside the implanted ion region did not amorphize even after damage levels > 5 dpa. The amorphous layer in the Fe-implanted region of Si3N4 did not appear if the specimen was simultaneoulsy irradiated with 1-MeV He{sup +} ions at RT. By comparison with published results, ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys have replaced resins as a material for the components of electronic products such as cell phone and notebook personal computer mainly, because of their lightness and rigidity. Thin walls, a complicated shape, and high appearance quality are all needed in the external parts. Die-casting and injection molding are the main method of manufacturing magnesium alloy parts. The optimal cast conditions and mold design have been investigated in order that a few defects such as surface cracks and mold cavities in casting parts would be reduced. Instead of cast, plastic forming technologies such as warm drawing and hot forging have been developed to form thinner walls and less defects. Plastic formability of magnesium alloy in hot working is dependent on a grain size of material. The material with fine grains has advantage of being formed at high strain rate. The characteristics of forming processes of ...

Energy Technology Data Exchange (ETDEWEB)

Machines and structures, such as automobiles are usually subjected to biaxial or three-axial stresses instead of uniaxial stress. However, research on a fatigue failure under multi-axial stress has not been fully presented because such experiments are difficult. To solve this problem, we developed the servo biaxial fatigue-testing machine. In this research, we performed the biaxial fatigue tests of a magnesium alloy in order to clarify the effects from different heat treatments. Magnesium alloy is the lightest in weight among metal materials for structural use. The fatigue characteristics of a magnesium alloy are indispensable in order to create the design which ensures the reliability and the safety of the vehicles especially in long-distance run. The main conclusions are summarized as follows; (1) The mechanical property of magnesium alloy AZ31B falls by heat treatment at low temperature. (2) The ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are ideal candidates to benefit from equal channel angular extrusion (ECAE) because of their poor forming characteristics due to a hcp structure. In this study, ECAE processing was applied to ZK31 and AZ31 magnesium alloys under various conditions. The grain size of as-ECAE specimens decreases with decreasing the processing temperature, however, the grain size decreases slightly with increasing number of repetitive processing. Both the tensile strength and 0.2% proof stress of as-ECAE specimens are high when processed at low temperature, but the elongation is high when processed at high temperature. Crystal orientation is different in the two alloys and it also varies according to the processing temperature for the two alloys. The difference of the crystal orientation influences the tensile properties, especially 0.2% proof stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

International Nuclear Information System (INIS)

Luminescence and reflection spectra as well as luminescence kinetics of the 1 mol% Sm3+-doped crystalline lanthanum magnesium meta borate (LaMgB5O10) and gadolinium magnesium meta borate (GdMgB5O10) were analyzed. Materials were synthesized by conventional solid state route and showed bright orange-red emission under UV excitation. Emission spectra contain sharp and well resolved Sm3+4G5/2#->#6HJ transitions indicating a strong crystal-field effect. In case of gadolinium compound energy transfer between Gd3+ and Sm3+ was detected. The luminescent kinetics of the Sm3+ in analyzed powders is characterized by single exponential decay and experimental values vary in the range 2.2-2.4 ms. - Research highlights: ? Phosphorescence of samarium-doped lanthanide magnesium meta borates. ? Bright and well resolved orange-red emission of Sm3+ under UV excitation. ? Energy transfer from Gd3+ to Sm3+ in gadolinium ...

Science.gov (United States)

... having high fluidity. The SC-51A alloy contains 4.5 to 5.5% silicon, 1 to 1.5% coppers .4 to .6% magnesium, o35% sine, .8% iron, .5% manganes*, ...

UK PubMed Central (United Kingdom)

A novel therapeutic compound was found to induce bladder tumors in male rats. Given the location of the tumors and the increased amounts of calcium- and magnesium-containing solids found in the urine...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The possibility of improving the cold formability of wrought magnesium alloys is considered in light of their good hot forming characteristics. Magnesium alloy AZ31B sheet is selected as a model system. Parameters affecting formability, such as strain hardening rate, strain rate sensitivity, and the degree of anisotropy are examined systematically by conducting tensile tests over a range of temperatures (room temperature to 250 C) and strain rates (1 x 10{sup -5} to 0.1 s{sup -1}). The plastic anisotropy and deformation texture evolution are examined in samples aligned with the sheet rolling and transverse directions. Polycrystal plasticity simulations using a viscoplastic self-consistent (VPSC) formulation are used to model the observed anisotropy and texture evolution. The adjustable parameters in the model are the relative critical resolved shear stresses of the dislocation mechanisms known to operate within magnesium. ...

International Nuclear Information System (INIS)

Chemical and phase homogeneity of titanium-niobium sponge, produced by a combined magnesium-thermic reduction of niobium pentachloride and titanium tetrachloride mixtures, is investigated. It is ascertained that a sponge consists of spherical shape particles and has a large number of pores. Particle sizes are reduced with niobium being substituted for titanium from 50-500 #mu#m for titanium sponge to 1-40 #mu#m for niobium one, which testifies to the bormation in a titanium-niobium sponge of an alloy and not a mechanical mixture. A number of solid solutions is detected by X-ray phase analysis. Lattice parameters are determined.

British Library Electronic Table of Contents (United Kingdom)

A new coumarin-based sensor molecule (L1) has been synthesized and this was found to bind calcium and magnesium ions more effectively as compared to other alkali/alkaline earth/lanthanide and certain transition metal ions. A significant enhancement in fluorescence intensity was observed on binding to Ca2+ and Mg2+ ions; while a minor quenching was observed for weakly bound Hg2+, Ni2+, Fe3+, and Co2+ ions. PET process, coupled with the ICT process, is proposed to explain the observed spectral response.

Energy Technology Data Exchange (ETDEWEB)

Optimum conditions for microstructural control in industrial hot working of cast and homogenized AZ31 magnesium alloys are evaluated by using a processing map. The recommended window for bulk metal working of this alloy is the domain in the temperature range 300-450 C and strain rate range 1-10 s{sup -1}, and the optimum processing parameters are 400 C and 10 s{sup -1}, where grain-boundary self diffusion is the rate-controlling mechanism. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The superplastic characteristics and diffusion bonding behaviors were investigated in commercial 7475 aluminum alloy and AZ31 magnesium alloy sheets. In this study, the presently used materials behaved in a superplastic manner at {proportional_to} 773 K (7475Al) and {proportional_to} 523 K (AZ31). Then, by the theoretical relationship between pressure and time, these materials were successfully diffusion bonded at the superplastic temperatures. The bonding strength was more than 65 MPa. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

J-STORE (Japan)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The ...

International Nuclear Information System (INIS)

... ammonium compounds benzilic acid chemical preparation lanthanum oxides

Energy Technology Data Exchange (ETDEWEB)

A hydrous oxide film for the application as dielectric film is synthesized by immersion of pure aluminum in hot water. From a Rutherford backscattering analysis, the ratio of aluminum to oxygen atoms was found to be 3:2 in the anodized aluminum oxide film, and 2:1 in the hydrous oxide layer. Anodization of the hydrous oxide layer was more effective for the transition of amorphous anodic oxides to the crystalline aluminum oxides.

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

A press formability of magnesium alloy sheet cannot be evaluated by only general characteristics in tensile test; tensile strength, elongation n-value and r-value. For example, AZ31-alloy elongates about 20% in room temperature but breaks easily at shallow stage in deep drawing, which is caused by little local elongation (local necking). Crystallographic restriction of slip deformation in this alloy produces high strength, which almost equal to macroscopic fracture strength. In press forming, the bending under high tension requires a large deformability. A great difference in the deformability between AZ31 magnesium alloy and a strain hardened A1100 Aluminum (only 5% in elongation) is shown by static bending test with V-notch. In a rolled plate of AZ31, a crack is produced by stress concentration and propagates with reduced load at all testing temperature up to 453 K. In contrast, the point of notch in A1100 is dulled by local plastic ...

Energy Technology Data Exchange (ETDEWEB)

There are many factors affecting diffusion bonding in order to obtain high quality joining. Therefore, in the beginning, we constructed diffusion bonding model based on void growth mechanism to predict bonding pressures and times. In addition, in order to compare theoretical values with experimental values, diffusion bonding tests were carried out by using commercial AZ31 magnesium alloy sheets with different grain sizes, 16 and 130 {mu}m. The present AZ31 alloys were successfully diffusion bonded at several conditions, and the bonding strength was more than 0.8 of each parent materials. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This research investigated the inhibiting effects that sodium salts of linear monocarboxylic acids displayed towards the corrosion process of AZ31 Mg alloy in ASTM D 1387 saline solution (a synthetic industrial cooling water). The length of the aliphatic chain of the acids ranged between 7 and 15 carbon atoms. The inhibiting action of these salts can be related to the precipitation of an insoluble magnesium salt, which mainly affected the anodic reaction. The aliphatic chain length controlled the anion solubility and the reaction rate of magnesium carboxylate formation. For all the salts, an optimum concentration was experienced: 10{sup -2} M for sodium decanoate (caprate), 10{sup -3} M for sodium dodecanoate (laurate), 10{sup -4} M for sodium tetradecanoate (myristate); when this concentration was exceeded, a diminution (even a disappearance) in the inhibiting action was found. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The development of a twinned microstructure in hexagonal close-packed rolled magnesium compressed in the in-plane direction has been monitored in situ with neutron diffraction. The continuous conversion of the parent to daughter microstructure is tracked through the variation of diffraction peak intensities corresponding to each. Approximately 80% of the parent microstructure twins by 8% compression. Elastic lattice strain measurements indicate that the stress in the newly formed twins (daughters) is relaxed relative to the stress field in the surrounding matrix. However, since the daughters are in a plastically 'hard' deformation orientation, they quickly accumulate elastic strain as surrounding grains deform plastically. Polycrystal modeling of the deformation process provides insight about the crystallographic deformation mechanism involved.

Energy Technology Data Exchange (ETDEWEB)

Grain refinement in AZ31 magnesium alloy has been attempted by hot-rolling and annealing process. Specimens were solution heat treated at 673 K for 36 ks, then hot-rolled at 423-773 K with total reduction of 20-80% by multi pass process. The rolled specimens were annealed at 473-673 K for 3.6 ks. Grain sizes after the solution heat treatment were about 20 to 150 {mu}m. After hot-rolling at 573 K and annealing at 473 K, grain sizes decreased into about 5 to 10 {mu}m. Suppression of grain growth by pinning due to precipitates was observed by transmission electron microscopic observations. (orig.)

J-STORE (Japan)

Full Text Available

International Nuclear Information System (INIS)

Short communication.

Energy Technology Data Exchange (ETDEWEB)

Short communication

International Nuclear Information System (INIS)

Bi-U mixed oxides were synthesized by two methods and characterized by X-ray diffraction and X-ray photoelectron spectroscopy. The samples were tested for the catalytic oxidation of carbon monoxide by oxygen. A stepwise redox mechanism consistent with the kinetic results is proposed. (orig.).

International Science & Technology Center (ISTC)

Development of Method and Technical Project of the Plant for Thermo-Vacuum Desorption of Tritium Oxide (HTO) from the Environmental Samples

KoreaScience (Korea)

Full Text Available

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and ...

Science.gov (United States)

A number of alloys of zirconium have been investigated as part of a program aimed at improving the high-temperature tensile and creep strength of zirconium. These alloys include aluminum, beryllium, lead, magnesium, molybdenum, niobium, tantalum, tin, titanium, tungsten, vanadium, and zinc, binary and ternary alloys. The data indicate that aluminum, lead, molybdenum niobium, tin, titanium, tungsten, and vanadium can be used successfully to harden zirconium, and that aluminum, tin, titanium, and vanadium are particularly effective in maintaining the strength of zirconium at elevated temperatures.

Science.gov (United States)

A laser spectrometer for the ethylenediaminetetra-acetic acid (EDTA) titration of magnesium or calcium ions that is designed around a handheld laser pointer as the source and a photoresistor as the detector is developed. Findings show that the use of the spectrometer reduces the degree of uncertainty and error in one part of the EDTA titrations, however overall standard deviations depend on the skill of the student and their willingness to be careful and precise.

Science.gov (United States)

The effect of hydrogen sulfide (H2S) on the chemical looping combustion of coal-derived synthesis gas with bentonite-supported metal oxidesssuch as iron oxide, nickel oxide, manganese oxide, and copper oxideswas investigated by thermogravimetric analysis, mass spectrometry, and X-ray photoelectron spectroscopy (XPS). During the reaction with synthesis gas containing H2S, metal-oxide oxygen carriers were first reduced by carbon monoxide and hydrogen, and then interacted with H2S to form metal sulfide, which resulted in a weight gain during the reduction/sulfidation step. The reduced/sulfurized compounds could be regenerated to form sulfur dioxide and oxides during the oxidation reaction with air. The reduction/oxidation capacities of iron oxide and nickel oxide were not affected by the presence ...

Energy Technology Data Exchange (ETDEWEB)

An investigation of the mechanism of the oxidation and ammoxidation of propylene was made. The products of the above reactions were acrylonitrile and acrolein for ammoxidation and oxidation, respectively. Also, the ammoxidation and oxidation of allyl alcohol, allyl amine, and their allylic deuterium substituted analogues was studied. It was concluded that oxidation and ammoxidation of propylene have the same rate determining step. Other conclusions about the reaction intermediates were also made.

UK PubMed Central (United Kingdom)

The widely accepted oxidative stress theory of aging postulates that aging results from accumulation of oxidative damage. Surprisingly, data from the longest-living rodent known, naked mole-rats [MRs;...Full Text Available

UK PubMed Central (United Kingdom)

Oxidative stress occurs when the level of prooxidants exceeds the level of antioxidants in cells resulting in oxidation of cellular components and consequent loss of cellular function. Oxidative...Full Text Available

UK PubMed Central (United Kingdom)

Studies were conducted to quantitate the evolution of nitrogen oxides (NO_(x)) from soybean [Glycine max (L.) Merr.] leaves during in vivo nitrate reductase...Full Text Available

UK PubMed Central (United Kingdom)

The potential for oxidation of ammonia in anoxic marine sediments exists through anaerobic oxidation by Nitrosomonas-like organisms, utilizing nitrogen dioxide, coupling of nitrification,...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Superplasticity of polycrystalline metallic materials is a phenomenon which shows hundreds to thousands of percents of large plastic deformation without necking in a steady state of low stress, when the uni-axial tensile loading is done in some special thermo-mechanical conditions (some limited ranges of properly high temperature and low strain rate). The main mechanism of superplastic phenomenon is the grain boundary sliding, while the main mechanism of usual plastic deformation is the trans-granular sliding. In this research, the possibility of superplastic deformation in a magnesium alloy (AZ31Mg alloy) was experimentally investigated, because generally speaking, the magnesium alloy whose atomic structure is hexagonal does not have enough formability in a form of trans-granular sliding mechanism. In this paper, the detail of experimental results are shown and discussed. Moreover, the constitutive equations of Mg alloy are proposed on the ...

Energy Technology Data Exchange (ETDEWEB)

The tensile and compressive properties as well as LCF and HCF performance of the extruded magnesium alloys AZ31 and AZ80 were determined in extrusion (L) and long-transverse (T) directions. Owing to marked crystallographic textures, both alloys showed pronounced directional mechanical properties in monotonic as well as cyclic loading with strength values in L-direction being significantly superior to those in T-direction. Thermomechanical treatments such as pressing, swaging and rolling were found to increase yield stresses and HCF strengths and to alter the directionality in properties due to textural modifications. To further improve HCF strengths, mechanical surface treatments such as shot peening, roller-burnishing and deep rolling were utilized. The results indicate marked improvements provided that suitable process parameters are used. The improvement of the HCF strengths is explained by the process-induced changes in near-surface dislocation densities and ...

Energy Technology Data Exchange (ETDEWEB)

In order to enhance the mechanical properties of magnesium alloy (AZ31) sheet, an integrated sheet-making process including billet casting, extrusion and rolling was attempted. Microstructural analysis was carried out and the mechanical properties at each processing step were also investigated by tensile tests. By an extrusion process of ingot-processed billet, average grain size of billet was reduced from 91.2 to 28.2 {mu}m, and a further reduction in grain size to 16.9 {mu}m was obtained by subsequent rolling of extruded 5 mm thin slab. In the final step, a rolled sheet of 1 mm showed a remarkable refinement in grain size down to 8.8 {mu}m. Regarding mechanical properties, tensile strength and elongation for as-cast billet, as-extruded thin slab and as-rolled sheet increased from 189, 258 to 234 MPa, and from 13, 16.5 to 23%, respectively. (orig.)

British Library Electronic Table of Contents (United Kingdom)

In the present study, new light weight nano-composites (AZ31B-3.3Al2O3-Cu) based on magnesium alloy AZ31B are developed using disintegrated melt deposition technique. Microstructural characterization studies revealed grain refinement and significant increase in amount of second phases as a result of increasing presence of copper. All the samples exhibited minimal porosity and good matrix-second phase interfacial integrity. The results also showed that addition of both nano-Al2O3 and Cu led to a simultaneous improvement in 0.2% yield compressive strength (0.2%YCS), ultimate compressive strength (UCS) and work of fracture (WoF) of the AZ31B magnesium alloy while failure strain was marginally affected. The results of this study clearly illustrate the capability of AZ31B-Al2O3-Cu formulations ...

Energy Technology Data Exchange (ETDEWEB)

Microstructure evolution under hot deformation was investigated in compression of a magnesium alloy AZ31 at 673 K (0.73T{sub m}). Two kinds of samples were machined along the parallel and transverse direction of the extruded rods. New fine grains are evolved at corrugated grain boundaries at low strains and developed rapidly in grain interiors in the medium range of strain, finally leading to a roughly full evolution of equiaxial fine grains. Kink bands are evolved at corrugated grain boundaries and in grain interiors at low strains. The boundary misorientation of kink band increases rapidly with increasing strain. These characteristics of new grain evolution process are not changed by the orientation of the samples, while the flow behaviors clearly depend on it. It is concluded that new grain evolution can be controlled by a deformation-induced continuous reaction resulting in grain fragmentation by kink bands, i.e. continuous dynamic recrystallization (DRX). The ...

Energy Technology Data Exchange (ETDEWEB)

Apparatus and method for selective measurement of tritium oxide in an environment which may include other radioactive components and gamma radiation, the measurement including the selective separation of tritium oxide from a sample gas through a membrane into a counting gas, the generation of electrical pulses individually representative by rise times of tritium oxide and other radioactivity in the counting gas, separation of the pulses by rise times, and counting of those pulses representative of tritium oxide. The invention further includes the separate measurement of any tritium in the sample gas by oxidizing the tritium to tritium oxide and carrying out a second separation and analysis procedure as described above.

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

Science.gov (United States)

Continuous wave lasing operation with the shortest wavelength for semiconductor lasers was obtained from AlGaInP double heterostructure lasers at 77 K. The structure was grown by metalorganic vapor phase epitaxy. Lasing wavelength was 583.6 nm (yellow). Threshold current was 43 mA (1.9 kA/cm/sup 2/). Magnesium was adopted as a p-type dopant, and was proved to be preferable for a high aluminum composition AlGaInP cladding layer.

International Nuclear Information System (INIS)

The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.

International Nuclear Information System (INIS)

The potential use of uranium in the field of catalysis is presented in the first part of this paper. Numerous applications of uranium binary oxides, as well as mixed oxides, are reviewed with a special emphasis on the role of U-Sb-O catalysts in selective oxidation (and ammoxidation) processes. Attempts are made to correlate the electronic structure of uranium, and especially the role that 5f electrons play in bonding, with its promising catalytic properties. In the second part, new data are given for uranium-bismuth mixed oxides in the catalytic oxidation of CO by O_2. Kinetic tests performed in a flow microreactor allow a mechanism to be proposed that involves the direct participation of lattice oxygen of the catalyst in the chemical process (redox mechanism). The high activity can be related to the ability of uranium to change reversibly its oxidation state. ...

Energy Technology Data Exchange (ETDEWEB)

The potential use of uranium in the field of catalysis is presented in the first part of this paper. Numerous applications of uranium binary oxides, as well as mixed oxides, are reviewed with a special emphasis on the role of U-Sb-O catalysts in selective oxidation (and ammoxidation) processes. Attempts are made to correlate the electronic structure of uranium, and especially the role that 5f electrons play in bonding, with its promising catalytic properties. In the second part, new data are given for uranium-bismuth mixed oxides in the catalytic oxidation of CO by O/sub 2/. Kinetic tests performed in a flow microreactor allow a mechanism to be proposed that involves the direct participation of lattice oxygen of the catalyst in the chemical process (redox mechanism). The high activity can be related to the ability of uranium to change reversibly its oxidation ...

UK PubMed Central (United Kingdom)

Ethane oxidation was studied in ethane-grown resting cells (mycelia) of an Acremonium sp. and in cell-free preparations of such mycelia. From resting cell experiments evidence was found for a pathway...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Alkali metal doped double perovskites containing manganese and at least one of cobalt, iron and nickel are useful in the oxidative coupling of alkane to higher hydrocarbons.

Science.gov (United States)

May 31, 2011 ... A Theoretical Solid Oxide Fuel Cell Model for System Controls and Stability Design AUTHOR(S): Kopasakis, George; Brinson, Thomas; Credle, ...

Energy Technology Data Exchange (ETDEWEB)

Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the ...

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Czech Academy of Sciences Repository

Full Text Available

Science.gov (United States)

Not Available

International Nuclear Information System (INIS)

On the basis of experimental and extrapolated values the physico-chemical properties of astatine are reviewed considering all oxidation states.

International Nuclear Information System (INIS)

The influence of MeV electrons irradiation on the gate oxide layers of hydrogenated polysilicon thin film transistors (TFTs) was investigated by measuring gate leakage currents and threshold voltages. The experimental data revealed a decrease of oxide trap density and increase of positive oxide charge. Improvement in the interface roughness and in the oxide quality near the bottom interface was observed.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

We report on the fouling of Focused Ion Beam (FIB)-fabricated silicon oxide nanopores after exposure to tap water for two weeks. Pore clogging was monitored by Scanning Electron Microscopy (SEM) on both bare silicon oxide and chemically functionalized nanopores. While fouling occurred on hydrophilic silicon oxide pore walls, the hydrophobic nature of alkane chains prevented clogging on the chemically functionalized pore walls. These results have implications for nanopore sensing platform design.

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

DEFF Research Database (Denmark)

ATPase, endoplasmic reticulum, calcium, ischaemia

International Nuclear Information System (INIS)

By means of ESCA the composition and the thickness of passive films formed on austenitic stainless steels were investigated after the attack of nitric acid at various temperatures and acid concentrations. The outermost layers of the oxide film consist of SiO_2, then a layer rich of Cr-oxid follows, containing also some Mo in the four- and sixvalent state. Ni does not contribute to the oxide film. Cr is also enriched in the metal just below the oxide film. (orig.).

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared

KoreaScience (Korea)

Full Text Available

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

... AT THE INTERFACE, A THIN OXIDE LAYER IS OBSERVED ALONG WITH POSSIBLE PALLADIUM SILICIDES. PALLADIUM ...

Energy Technology Data Exchange (ETDEWEB)

The effect of sodium on the partial oxidation of methane over MoO{sub 3}-SiO{sub 2} in the presence of molecular oxygen has been investigated. As in the sodium-free case, the major products are formaldehyde, carbon monoxide, carbon dioxide, and water. Kinetic analysis indicates that methane is directly oxidized to formaldehyde and carbon dioxide. Formaldehyde is oxidized to carbon monoxide, which is itself further oxidized, providing an alternative route to carbon dioxide. The kinetic model shows that sodium poisons the direct oxidation of methane to formaldehyde and carbon dioxide, but promotes the oxidation of formaldehyde and carbon monoxide. Model predictions of rates and selectivities are in good agreement with the experimental data. A mechanism that explains both the poisoning and promotion effects of sodium on MoO{sub 3}-SiO{sub 2} is proposed.

Energy Technology Data Exchange (ETDEWEB)

Titanium oxides were grown anodically to selected final potentials on grade II polycrystalline titanium under different anodization rates. XPS and RBS results show that the oxide consists of primarily TiO2 with a non-stoichiometric oxide/metal interface, with the slower growth rate associated with a thicker layer at the interface. Characterization using TEM reveals that the structure of the oxide evolves from a primarily amorphous phase to islands of crystallites in an amorphous matrix, to an entirely crystalline phase by increasing the polarization potential. Slower growth rates tend to remain crystalline at higher potentials. The mechanical strength of oxide films extracted from load-depth data by nanoindentation varies dramatically for oxide films grown by different rates at 9.4 V, and to a lesser extent at lower potentials. The variation of film strength is ...

International Nuclear Information System (INIS)

Synergism has been observed during inhibiting initiated oxidation of styrene or tetralin by organic phosphites in the presence of complex compounds of some transition metals. The results are given of non-additive intensification of antioxidative activity of triphenylphosphite (TPP) and tri-(4-methyl-6-tert.-- butyl)-phenyl-phosphite (TMBP) in the process of initiated oxidation of styrene or tetralin with addition of acetylacetonates of cobalt and vanadyl. During styrene oxidation, inhibition of the reaction with chelate complex of vanadyl is weakened considerably when phosphite is added into the reaction system. During tetralin oxidation, postcatalytic (or branched) oxidation is observed only for large concentration of vanadyl complex. Addition of TPP to above complex sharply increases the induction period. When the induction period is completed, oxidation of ...

Energy Technology Data Exchange (ETDEWEB)

The oxidative dehydrodimerization of propylene to C/sub 3/-dimers (1,5-hexadiene and benzene) has been examined at 600/sup 0/C and atmospheric pressure using a (Bi/sub 2/O/sub 3/)/sub 0.85/(La/sub 2/O/sub 3/)/sub 0.15/ oxide ion-conducting catalyst in a reactor where a catalyst disk separates a feed of propylene in helium from air. The surface of the disk exposed to propylene was reoxidized not by gaseous O/sub 2/, but by the dissociative adsorption and reduction of dioxygen at the oxidant side of the disk, followed by oxide ion conduction to replace spent lattice oxygen. Selectivity to C/sub 3/-dimers when using lattice oxide migration to reoxidize the catalyst was considerably greater than when O/sub 2/ was added to the propylene feed under the same reaction conditions. This result supports the proposal that lattice oxygen is predominantly involved in the selective ...

Energy Technology Data Exchange (ETDEWEB)

This work reports studies of ethanol oxidation on Pt-Sn/C catalysts with nearly the same particle size and identical overall composition having different amounts of oxide and alloyed phases. Results of characterization of physical properties by transmission electron microscopy (TEM), X-ray diffraction (XRD), differential scanning calorimetry (DSC), X-ray photoelectron spectroscopy (XPS), and in situ dispersive X-ray absorption spectroscopy (DXAS) are presented. The variation in the amount of oxide and alloyed phases, promoted by heat treatments in mild temperature conditions, does not produce any significant particle growth. Cyclic voltammetry and oxidation of adsorbed CO in acid medium are used to probe the surface conditions. Data on the electrocatalytic activity towards ethanol oxidation, obtained by potential sweeps and chronoamperometry, are discussed and correlate well with ...

International Nuclear Information System (INIS)

The procedure of charge-coupled devices (CCD) are investigated by using MOS capacitors for enhancing their ionizing radiation tolerance. Authors have found that the gate oxidation temperature, thickness of SiO_2 gate insulator and high temperature processes after gate oxidation are crucial for determining the radiation tolerance of the devices, and proposed to decrease the thickness of gate insulator, perform gate oxidation at 1000 deg C by means of dry oxidation and minimize the number of high temperature procedure steps after gate oxidation. All stated above is a necessary preparation for priducing radiation hardened charge-coupled devices.

Energy Technology Data Exchange (ETDEWEB)

Cathodic arc deposition is an established and industrially applied technique for the formation of nitrides (e.g. TiN); it can also be used for metal oxide thin film formation. A cathodic arc plasma source with the desired cathode material is operated in an oxygen atmosphere of appropriate pressure, and metal oxides of various stoichiometric composition can be formed on different substrates. We report here on a series of experiments on metal oxide formation by cathodic arc deposition for different applications. Black copper oxide has been deposited on accelerator components to increase the radiative heat transfer between the parts. Various metal oxides such as tungsten oxide, niobium oxide, nickel oxide and vanadium oxide have been deposited on ITO glass to form electrochromic films for window ...

British Library Electronic Table of Contents (United Kingdom)

Zirconium and particularly Zr-2.5wt%Nb (Zr2.5Nb) alloy are useful for engineering bearing applications because they can be oxidized in air to form a hard surface ceramic. Oxidized zirconium (OxZr) due to its abrasion resistant ceramic surface and biocompatible substrate alloy has been used as a bearing surface in total joint arthroplasty for several years. OxZr is characterized by hard zirconium oxide (oxide) formed on Zr2.5Nb using one step thermal oxidation carried out in air. Because the oxide is only at the surface, the bulk material behaves like a metal, with high toughness. The oxide, furthermore, exhibits high adhesion to the substrate because of an oxygen-rich diffusion hardened zone (DHZ) interposing between the oxide and the substrate. In this study, we demonstrate a two step pro...

Energy Technology Data Exchange (ETDEWEB)

The oxide colloidal route, developed in the laboratory for mono-metallic catalysts, consists in preparing a metallic oxide hydro-sol which leads to the supported catalyst after deposition onto a support and an activation stage. In this work, this method has been adapted to the preparation of alumina supported bimetallic Pd-Sn catalysts to determine its interest for the control of the properties of the bimetallic phase (size, composition and structure). In the preliminary study concerning tin oxide sols, SnO{sub 2} (size=2,3 nm) and Sn{sub 6}O{sub 4}(OH){sub 4} (size = 25 nm) nano-particles were synthesized by neutralization respectively for tin(IV) and tin(H). The control through the pH of the aggregation of the PdO and SnO{sub 2} particles revealed that increasing oxide solubility promotes integral re-dispersion of the oxide particles. To synthesize oxide ...

International Nuclear Information System (INIS)

The formation of thin SiO_2 layers on silicon and metal silicides was studied by phase- and thickness measurements with Rutherford back-scattering of 2 MeV alfa particles. Thermal oxidation was done in steam and dry oxygen at temperatures between 750 degrees Celsius and 1 100 degrees Celsius, while SiO_2 formation at room temperature was carried out by anodic oxidation. The study of silicon oxidation was done on Si<100>, Si<111> and amorphous silicon substrates. Thermal oxidation of CoSi_2, CrSi_2, NiSi_2, PtSi and TiSi_2 was investigated. The oxidation rates of the silicides were found to be much higher than for silicon. The oxidation process is also diffusion-limited with a higher oxidation rate for steam as compared to dry oxygen. The silicide layers were found to stay intact during thermal oxidation. A ...

British Library Electronic Table of Contents (United Kingdom)

Regularities of deformation-induced dissolution of a surface layer of iron oxides in matrixes of iron-based alloys with bcc and fcc lattices have been studied by the methods of M?ssbauer spectroscopy, transmission electron microscopy, and X-ray diffraction. A method of producing iron alloys strengthened by dispersed oxide nanoparticles and alloyed with elements possessing a high affinity to oxygen (titanium and yttrium) has been proposed, which implies a dynamic dissolution of a surface layer of iron oxides upon strong cold deformation and a precipitation of secondary yttrium and titanium nanooxides upon a subsequent high-temperature sintering of mechanically alloyed powders. There has been demonstrated a possibility of oxide strengthening of pure iron upon its interaction with air without...

International Nuclear Information System (INIS)

Heat capacities and densities of aqueous MgCl/sub 2/, CaCl/sub 2/, and SrCl/sub 2/ from the accompanying paper are combined with literature data up to 473 K to yield temperature-dependent equations by using the ion-interaction model of Pitzer. These heat capacity equations have been integrated to yield the enthalpy and the Gibbs energy. The enthalpy parameters for 298 K are evaluated in separate calculations using published high-temperature osmotic data as well as heats of dilution, while the Gibbs energy parameters for 298 K are taken from the literature. The range of validity of the final equations is described.

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

Energy Technology Data Exchange (ETDEWEB)

Counter-current regeneration of 2-stage sodium zeolite softeners has been employed in reducing hardness leakage level of steamflooding water to less than 1 ppm when raw water contains as much as 5,000 ppm of the total dissolved solids. Hardness leakage is caused by sodium displacement of calcium and magnesium from the bottom of the exchanger bed. This study presents nomographs providing for rapid calculations to be made, for which a convenient operational mode does not already exist. The nomographs relate the hardness leakage as a function of salt quality and influent water quality and present solutions for predicting the leakage level, salt quality requirement or the treatability of raw water required for steamflooding projects.

International Nuclear Information System (INIS)

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 ?m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

Energy Technology Data Exchange (ETDEWEB)

Materials for the construction of cold neutron sources must satisfy a range of demands. The cryogenic temperature and irradiation create a severe environment. Candidate materials are identified and existing cold sources are briefly surveyed to determine which materials may be used. Aluminum- and magnesium-based alloys are the preferred materials. Existing data for the effects of cryogenic temperature and near-ambient irradiation on the mechanical properties of these alloys are briefly reviewed, and the very limited information on the effects of cryogenic irradiation are outlined. Generating mechanical property data under cold source operating conditions is a daunting prospect. It is clear that the cold source material will be degraded by neutron irradiation, and so the cold source must be designed as a brittle vessel. The continued effective operation of many different cold sources at a number of reactors makes it clear that this can be accomplished. 46 refs., 8 ...

Energy Technology Data Exchange (ETDEWEB)

In the present study, element interdiffusions at the cofired interface of 9/1 Ag/Pd electrode and lead magnesium niobate (PMN)-based ferroelectrics were investigated using Auger Electron Spectroscopy (AES). Intense interdiffusions at the interface were observed while Ag and Pd could penetrate into the ceramics for about 1 {mu}m. Ag-doping experiments were carried out to further study the effects of Ag diffusion on electrical properties of the ceramics. The results showed that Ag could be incorporated into solid solution of the ceramics as Ag{sup +}. As a whole, the Curie temperature (Tc) and dielectric constant of the ceramics decreased with Ag addition. However, Ag addition had no obvious effect on the insulation resistivity. The results inferred that Ag{sup +} could substitute for Pb{sup 2+} at A site of ABO{sub 3} lattice, thereby oxygen vacancies were generated.

International Nuclear Information System (INIS)

The microstructure of commercial rolled magnesium alloy AZ31B (nominal composition Mg-3Al-0.9Zn-0.15Mn in wt.%) was investigated with the help of light microscopy, electron backscatter diffraction (EBSD) and X-ray diffraction technique after annealing in the temperature range from room temperature (RT) to 400 deg. C. Tensile tests at RT were performed to show the influence of the microstructure on mechanical properties. Static recrystallization (SRX) was observed during annealing of as-received alloy at and above 150 deg. C. Twins play an important role during SRX and serve as nucleation sites and preferred paths for growth of grains. The strong basal texture caused by rolling was weakened by SRX. Significant differences in the stress strain curves were observed for as-received and annealed specimens.

International Nuclear Information System (INIS)

The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic slip systems.

British Library Electronic Table of Contents (United Kingdom)

A novel approach using reactive processing is explored that eliminates the labour-intensive separation of post-consumer polyolefin waste from the mixed plastics waste stream. The reactive compatibiliser BMI has been used to form a modified blend of PCPW with 40% improved tensile strength relative to the uncompatibilised control. Addition of 60 wt.-% magnesium hydroxide [Mg(OH)2] during reactive compatibilisation with BMI gave rise to an even more significant enhancement (up to 100%) of the tensile strength. BMI was also able to usefully enhance the properties of a composite based on calcium carbonate and the polyolefin waste.

International Nuclear Information System (INIS)

The study was conducted during 2000 to determine the role of various chemical plant factors viz., total minerals, nitrogen, fat contents, carbohydrate, macro an micro nutrients in the leaves of five genotypes of sugarcane i.e., BF-162, SPSG-26, L-118, CP-43/33 and CP-72/2086 by correlating the infestation of top borer, Scirpophaga Nivella F. at tillering stage. None of the genotype was found completely resistant to the pest. CP-43/33 and BF-162 proved susceptible and resistant varieties, respectively. Total mineral, manganese and copper contents did not show significant correlation with the pest infestation, whereas nitrogen, potassium, calcium, magnesium and ferrous contents played a positive and significant role. Phosphorous, carbohydrates, fats and zinc contents played a significant and negative effect on the pest infestation at tillering stage. (author)

Science.gov (United States)

... Accession Number : ADD141533. Title : Yttrium Oxides in Vacuum-Plasma- Sprayed CoNiCrAlY Coatings,. Descriptive Note : Journal Article,. ...

Wastenet

Emissions and residues: Emissions may include, inter alia, nitrogen oxides, carbon monoxide, sulphur dioxide and other oxides

UK PubMed Central (United Kingdom)

Reactive oxygen species (ROS), inevitable byproducts of aerobic metabolism, are known to cause oxidative damage to cells and molecules. This, in turn, is widely accepted as a pivotal determinant of...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The influence of surface oxides of variable composition and nonstoichiometry formed at high temperatures in air on the general corrosion resistance of ferritic chromium steel type 08H17T (Fe-17Cr-1Ti) in weak sulfuric acid has been studied. Anodic passive films formed on steel with different pretreatments have also been examined. The surface oxide of nearly stoichiometric composition formed at 300 C provides for the passive state of steel in sulfuric acid despite its depletion by chromium when compared with that for nonstoichiometric Cr-enriched oxide formed at 600 C. The dissolution and transformation of nonstoichiometric thermal surface oxide in sulfuric acid appear to take place through defect sites, {minus}Fe{sup 2+} ions, and oxygen vacancies of the n-type conductor. The passive film formed on the nonstoichiometric oxide film, which had been produced at 600 C, was found to be ...

Science.gov (United States)

... ADD137758. Title : The Oxidation Behavior of CoCrAlY, CoCrAl and Yttrium-Implanted CoCrAl Alloys Compared and Contrasted,. ...

Energy Technology Data Exchange (ETDEWEB)

A catalytic process for the oxidation of sulfur-containing gases , E.G., sulfur dioxide and simultaneous production of sulfuric acid wherein a sulfur-containing gas is reacted with an oxygencontaining gas in the presence of a catalyst comprising an iron group metal on a solid support comprising a zeolite in a silicaalumina matrix.

UK PubMed Central (United Kingdom)

The gelation kinetics of an in situ gelable hydrogel formulated from oxidized dextran (Odex) and N-carboxyethyl chitosan (CEC) were investigated rheologically. Both Schiff base...Full Text Available

British Library Electronic Table of Contents (United Kingdom)

Rheological properties of moderately concentrated solutions of cellulose in methylmorpholine N-oxide-dimethylformamide mixtures containing hydrophilic montmorillonite nanoparticles were studied. Film composite materials were prepared, and their physicomechanical properties and structural organization were studied.

UK PubMed Central (United Kingdom)

We report the use of cysteine-substituted mutants in conjunction with in situ oxidation to determine the physical proximity of a pair of engineered cysteines in the pore region of the voltage-gated...Full Text Available

UK PubMed Central (United Kingdom)

A multidisciplinary approach was used to study the effects of pollution from a marine fish farm on nitrification rates and on the community structure of ammonia-oxidizing bacteria in the underlying...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The OH-initiated photo-oxidation of n-butane was used as a source of 1- and 2-butoxy radicals. Reactions producing ketones and other organic compounds are explained. Rates of photolysis were determined and are discussed.

UK PubMed Central (United Kingdom)

Oxidative stress has been implicated in the etiology of age-related muscle loss (sarcopenia). However, the underlying mechanisms by which oxidative stress contributes to sarcopenia have not been thoroughly...Full Text Available

UK PubMed Central (United Kingdom)

Neurons in the hippocampal CA1 region are particularly sensitive to oxidative stress (OS), whereas those in CA3 are resistant. To uncover mechanisms for selective CA1 vulnerability to OS, we...Full Text Available

UK PubMed Central (United Kingdom)

Quantitative probing of heterogeneous regions in muscle is feasible with phosphorus-31 magnetic resonance spectroscopy because of the differentiation of metabolic patterns of glycolytic and oxidative...Full Text Available

UK PubMed Central (United Kingdom)

Bacterial nitric oxide synthases (bNOS) are present in many Gram-positive species and have been demonstrated to synthesize NO from arginine in vitro and in vivo. However, the physiological role...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The oxidation conditions were investigated for obtaining a higher productivity in the production of high strength carbon fiber from polyacrylonitrile (PAN). The effect of incorporation of 2 % comonomer such as methyl acrylate (MA), acrylate containing carboxylate (SA), acrylamide (AAm), and hydroxyethyl acrylate (HEA) on the oxidation conditions was also investigated. The measurement of DSC and bonded oxygen content revealed that the most effective comonomer for promoting the cyclization of nitril group and the bonding of oxygen was found to be SA, and the second best was AAm. The measurement of tensile strength of carbon fiber showed that the copolymer of SA, HEA, and MA gave a high strength fiber. It took a long time to oxidize the carbon fiber when it was oxidized at a temperature on which double layer structure was not formed. To shorten the production time, a method of combining the upper limit ...

UK PubMed Central (United Kingdom)

Systemic administration of lipopolysaccharide (LPS), which causes endotoxemia and systemic inflammation, has been reported to induce expression of the gene for type II inducible nitric oxide synthase...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behavior of lanthanide oxides in molten alkaline chloride media is of great concern in pyrochemical processes for advanced nuclear fuel cycle. We have studied the solubilities of various lanthanide oxides in LiCl-KCl eutectic melt. In general, lanthanide oxides appeared to be insoluble/sparingly soluble in LiCl-KCl eutectic at 723 K. However, europium oxide exhibited an abnormal behavior in solubility and redox chemistry. The solubility of europium oxide was measured to be 1-2 order of magnitude higher than those of other lanthanide oxides. This abnormal solubility may be attributable to different electrochemical behavior of europium in the same experimental conditions. Most lanthanides ion exists as trivalent oxidation states. However, we observed divalent europium dissolved in LiCl-KCl molten salt by applying electron ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a method comprising applying a passivation layer of CaF{sub 2} to the surface of a superconductive ceramic oxide by evaporation. The CaF{sub 2} layer is effective to passivate the oxide surface without disrupting the superconductive properties.

UK PubMed Central (United Kingdom)

There is increasing evidence of a biochemical link between lipid oxidation and bone metabolism. Paraoxonase 1 (PON1) prevents the oxidation of low-density lipoprotein (LDL) and metabolizes biologically...Full Text Available

UK PubMed Central (United Kingdom)

Anionic peroxidase from tomato (Lycopersicon esculentum) fruit oxidized indoleacetic acid (IAA) slowly in the presence of Mn²⁺ and dichlorophenol in acetate buffers. The...Full Text Available

UK PubMed Central (United Kingdom)

Evolution of nitrogen oxides (NO_(x), primarily as nitric oxide) from soybean (Glycine max [L.] Merr.) leaves during purged in vivo nitrate reductase assays...Full Text Available

Science.gov (United States)

A detection theory is developed for point-contact metal-oxide-metal (MOM) systems. A system with heterogeneous oxide strongly bonded to the substrate is considered. It is shown that the form of the functional connection between the barrier heights and the ultimate compressive strength of the oxide has no substantial influence on the voltage-current characteristics of the system. Quantitative analysis indicates that a MOM system can behave as a tunnel diode and as a diode with a Schottky barrier. The model permits the determination of the optimum construction of long-life detectors based on MOM point-contacts.-

Energy Technology Data Exchange (ETDEWEB)

This paper reports on hydrolysis of 10 metal salt aqueous solutions of 6 metal oxides that was conducted in supercritical water. Continuous and rapid production of metal oxide fine particles was achieved by mixing a metal salt aqueous solution with preheated water fed from another line. The reaction time required was less than 2 min. Particle size, morphology, and crystal structure of the obtained metal (hydrous) oxides were examined. Particle size (20 to 600 nm) was different among the system but the size range was relatively narrow in all the cases.

KoreaScience (Korea)

Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Partial oxidation of 2-propanol was carried out on AB{sub 1-x}B`{sub x}O{sub 3} (A=Ba, B=Pb, Ce, Ti; B`=Bi, Sb and Cu) type perovskite oxides. Acetone was the major product observed on all the catalysts. All the catalysts underwent partial reduction during the reaction depending on the composition of the reactant, nature of the B site cation and the extent of substitution at B site. The catalytic activity has been correlated with the reducibility of the perovskite oxides determined from Temperature Programmed Reduction (TPR) studies. (orig.)

International Nuclear Information System (INIS)

... compilation fission products j codes mixed oxide fuels neutron reactions

Science.gov (United States)

... Title : Effect of Yttrium on the Microstructure of Titanium Alloys,. ... The yttrium was added in the melting stage as an oxide or in the elemental form. ...

International Nuclear Information System (INIS)

(1978). United States Quan, B. Becker, M. Harris, DR Rensselaer Polytechnic

Energy Technology Data Exchange (ETDEWEB)

Measurements were completed on the solubility of cupric and cuprous oxides in liquid water and steam at controlled pH conditions from 25 to 400 C (77 to 752 F). The results of this study have been combined with those reported from this laboratory in two previous EPRI reports to provide a complete description of the solubility of these oxides and the speciation of copper dissolved in liquid water and steam as a function of oxidation state, temperature, pH, and in the case of steam, pressure. These constitute the first set of reliable data for cuprous oxide solubility over this range of conditions. For the more intensively studied CuO case, agreement was found between our results and those of previous studies of its solubility in steam, whereas only partial agreement was evident for its solubility in liquid water. For both oxides this disagreement often amounted to orders of ...

Science.gov (United States)

Thermal wet oxidations of GaP and Al{sub 0.4}Ga{sub 0.6}P at 650 degree sign C for various times have been performed. Comparisons are made on oxidation rates and post oxidation morphology. Transmission electron microscopy shows that when oxidizing GaP, polycrystalline monoclinic GaPO{sub 4}{center_dot}2H{sub 2}O forms without noticeable loss of phosphorus. Oxidation for 6 h or more leads to poor morphology resulting in cracks and detachment. A thickness expansion of about 2.5-3 times is noticed as a result of oxidation. In contrast, oxidized Al{sub 0.4}Ga{sub 0.6}P exhibits much better morphology without cracks or detachment from the substrate. The oxide has an almost amorphous-like microstructure. The oxidation process shows typical diffusion-limited reaction at long anneals. Preliminary work on the ...

International Nuclear Information System (INIS)

The behaviour of an elastomeric seal for vehicle brake Tandem master cylinder is measured and analyzed in temperature and brake fluids changed. Working conditions are simulated for different piston rod velocity and cylinder supply pressure, in temperature rising, brakefluid boundary and Nanoaluminum oxide brakefluid oxide brakefluid lubrication. The result shows that Nanoaluminum oxide brakefluid with its ball shape can highly reduce friction coefficient to avoid seal excessive wear and reduce slick slip in brake applications.

UK PubMed Central (United Kingdom)

A two-step purification protocol was used in an attempt to separate the constitutive NAD(P)H-nitrate reductase [NAD(P)H-NR, pH 6.5; EC 1.6.6.2] activity from the nitric oxide and nitrogen dioxide (NO_(x))...Full Text Available

International Nuclear Information System (INIS)

The following methods of quartz ceramics alloying were considered: alloying of initial quartz glass; introduction of alloying additive into water slip of quartz glass; porous materials impregnation with salt aqueous solutions and subsequent salt thermal decomposition with formation of stable oxides in pores of ceramics. Oxygen free compounds BN, SiB_4, SiC, Si_3N_4, REM oxides and transition metal oxides were used as alloying additives. Main properties of the materials and compositions obtained are presented.

Energy Technology Data Exchange (ETDEWEB)

Oxide catalysis plays a central role in hydrocarbon processing and improvements in catalytic activity or selectivity are of great technological importance because these improvements will translate directly into more efficient utilization of hydrocarbon supplies and lower energy consumption in separation processes. An understanding of the relationships between surface structure and catalytic properties is needed to describe and improve oxide catalysts. Our approach has been to prepare supported oxides that have a specific structure and oxidation state and then employ these structures in reaction studies. Our current research program is focused on studying the fundamental relationships between structure and reactivity for two important reactions that are present in many oxide-catalyzed processes, partial oxidation and carbon-carbon bond formation. ...

Energy Technology Data Exchange (ETDEWEB)

The Partnership for a New Generation of Vehicles (PNGV) program intends to develop new designs for automobiles that will reduce fuel consumption by two thirds but otherwise have price, comfort, safety, and other measures of performance similar to the typical automobile now on the market. PNGV vehicle designs are expected to substitute lightweight materials, such as aluminum, magnesium, carbon-reinforced polymer composites, glass-reinforced polymer composites, and ultra- light steel, for heavier materials such as steel and iron in automobile components. The target mass of a PNGV vehicle is 1,960 pounds, as compared to the average current vehicle that weights 3,240 pounds. Other changes could include the use of different ferrous alloys, engineering changes, or incorporation of advanced ceramic components. Widespread adoption of these vehicle designs would affect materials markets and require concurrent development and adoption of supporting technologies to supply the ...

British Library Electronic Table of Contents (United Kingdom)

Coordination of CoCl2 solutions to the silica polyamine composite, WP-1, made with the branched polymer polyethylenimine (PEI) shows irreversible binding resulting from surface oxidation of the Co2+-Co3+. This is not the case for the silica polyamine composite BP-1 made with the linear polymer polyallylamine where reversible binding and no oxidation is observed. These observations suggested that oxidation of the cobalt was related to the greater coordination number available with the branched polyamine relative to the linear polyamine. A study of the kinetics of cobalt binding to WP-1 indicated initial loading of Co2+ at relatively low coordination number followed by desorption of Co2+ leading to oxidation and irreversible binding. Exclusion of oxygen from the composite-cobalt solution mix...

International Nuclear Information System (INIS)

#beta#-sialon ceramics of equal overall compositions but containing amorphous, partly crystalline and almost completely crystalline intergranular phase(s) have been oxidized in oxygen at 1350 deg C for 20 hours. The obtained weight gain curves do not follow the parabolic rate law (#DELTA#W/A_0)"2= k_pt + #beta#. To the extent that crystallization occurs in the oxide scale during the oxidation experiment, the amorphous cross section area through which oxygen most easily diffuses will decrease with time. A brief description of this new rate law is given, and the obtained oxidation curves will be discussed within that framework. 4 refs., 2 tabs., 2 figs.

Energy Technology Data Exchange (ETDEWEB)

One-electron oxidation of several derivatives of pyrazolin-5-one, including the drug antipyrine, were studied by pulse radiolysis of aqueous solutions. All the compounds were found to be oxidized by Br2 rapidly but considerably more slowly by weaker oxidants, such as peroxyl radicals. From redox equilibria using p-methoxyphenol and N,N,N',N'-tetramethyl-p-phenylenediamine as reference compounds, the one-electron oxidation potentials of the methyl-substituted 2-pyrazolin-5-ones were found to be in the range of 0.32-0.39 V versus normal hydrogen electrode. The relevance of these findings to the properties of the drug nafazatrom is discussed. Antipyrine was found to have a much higher oxidation potential, estimated as 1.2-1.5 V, which is rationalized on the basis of the phenyl substitution and lack of resonance stabilization of the radical cation.

International Nuclear Information System (INIS)

The chemical composition and the semiconducting properties of passive films formed on nickel based alloy (Alloy 600) in acidic sulphate solution, pH 2.0 at room temperature were studied using Auger analysis, voltammetric techniques and the Mott-Schottky approach. The results obtained revealed that the presence of both chromium and mixed nickel-iron oxides in the films leads to the development of a p-n heterojunction, which controls their electronic structure, similarly manner to the case of stainless steels and Alloy 600 in borate buffer solution. This behavior has been interpreted as representing of an oxide system, which has a duplex character, with an inner p-type semiconducting region, mainly formed by chromium oxide and an outer n-type semiconducting region, containing iron oxide. It could also be observed that the nickel oxide present in the films acts as a barrier layer ...

Energy Technology Data Exchange (ETDEWEB)

Transient experiments in a Temporal Analysis of Products (TAP) Reactor were performed to elucidate the role of surface oyxgen species in the oxidation of benzene to phenol on ZSM-5 type zeolites with nitrous oxide as a selective oxidant. It was shown by puls experiments with nitrous oxide that the mean lifetime of the generated surface oxygen species is between 0.2s at 500 C and about 4.2 s at 400 C. Afterwards the surface oxygen species desorb as molecular oxygen into the gas phase where total oxidation will take place if hydrocarbons are present. Dual puls experiments consisting of a nitrous oxide puls followed by a benzene puls allowed studying the reactivity of the surface oxygen species formed during the first puls. The observation of the phenol formation was impeded due to the strong sorption of phenol. Multipulse experiments were necessary to reach a ...

International Nuclear Information System (INIS)

Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of titanium silicide at the boundary of the aluminide coating and ...

International Nuclear Information System (INIS)

Finding environmentally friendly and cost-effective methods to remediate soils contaminated with polycyclic aromatic hydrocarbons (PAHs) is currently a major concern of researchers. In this study, a series of small-scale semi-continuous extractions - with and without in situ wet oxidation - were performed on soils polluted with PAHs, using subcritical water (i.e. liquid water at high temperatures and pressures, but below the critical point) as the removal agent. Experiments were performed in a 300 mL reactor using an aged soil sample. To find the desorption isotherms and oxidation reaction rates, semi-continuous experiments with residence times of 1 and 2 h were performed using aged soil at 250 deg. C and hydrogen peroxide as oxidizing agent. In all combined extraction and oxidation flow experiments, PAHs in the remaining soil after the experiments were almost undetectable. In combined extraction and ...

Energy Technology Data Exchange (ETDEWEB)

Papers are presented on the development of oxidation- and sulfidation-resistant ferritic alloys; the microstructural stability of sulfidation-resistant FeCrAl stainless steels around 500 C; age hardening in Fe-Mn-Al-C austenitic alloys; the oxidation/corrosion behavior of low-Cr Fe-Cr-Ni alloys containing Zr or Nb; the high temperature oxidation/corrosion of iron-based superalloys; and the role of Mo in the Na/sub 2/SO/sub 4/ induced corrosion of superalloys at high temperature. Topics discussed include the effect of variations of Co content on the cyclic oxidation resistance of selected Ni-base superalloys; high temperature oxidation of Fe based alloys; the morphological development of high temperature oxide scales of Fe-Mn-Al base alloys; and the oxidation of an Fe-Mn-Al-C alloy at 1000 C. Consideration is given to the corrosion properties ...

Energy Technology Data Exchange (ETDEWEB)

From the alkalised crude extract of Symphytum cordatum (L.) W.K. roots, pyrrolizidine alkaloids (PAs) were extracted as free tertiary bases and polar N-oxides in a merely one-step liquid-liquid partitioning (LLP) in separation funnel and subsequently pre-fractionated by preparative multiple-development (MD) thin-layer chromatography (TLC) on silica gel plates. In this way three alkaloid fractions of different polarities and retention on silica gel plates were obtained as: the most polar N-oxides of the highest retention, the tertiary bases of medium retention, and diesterified N-oxides of the lowest retention. The former fraction was reduced into free bases by sodium hydrosulfite and purified by LLP on Extrelut-NT3 cartridge. It was further analysed together with the two other fractions by high-performance liquid chromatography (HPLC)-ion-trap mass spectrometry with atmospheric pressure chemical ionization (APCI) interface ...

Energy Technology Data Exchange (ETDEWEB)

For the reuse of a waste salt from an electrorefining process of a spent oxide fuel, a separation of rare earth elements by an oxidative precipitation in a LiCl-KCl molten salt was tested without using precipitate agents. From the results obtained from the thermochemical calculations by HSC Chemistry software, the most stable rare earth compounds in the oxygen-used rare earth chlorides system were oxychlorides (EuOCl, NdOCl, PrOCl) and oxides (CeO{sub 2}, PrO{sub 2}), which coincide well with results of the Gibbs free energy of the reaction. In this study, similar to the thermochemical results, regardless of the sparging time and molten salt temperature, oxychlorides and oxides were formed as a precipitant by a reaction with oxygen. The structure of the rare earth precipitates was divided into two shapes: small cubic (oxide) and large plate-like (tetragonal) structures. The ...

International Nuclear Information System (INIS)

Basic studies of the oxidation resistance of Fe-Cr binary and Fe-Cr-Ni ternary alloys in pure oxygen have shown that the excellent corrosion resistance of Alloy 800 is explicable in terms of the low defect concentrations and diffusion rates in the oxide forming on alloys of this composition in sufficiently oxidising environments. The performance of Alloy 800 in environments of particular importance to nuclear power generation is briefly reviewed to determine to what extent ideas derived from the basic studies of Fe-Cr-Ni ternary alloys are borne out in practice. The good corrosion resistance of Alloy 800 in steam and CO_2 and, to some extent, in molten salt environments is in agreement with the behaviour of ternary alloys in oxygen. Minor aliovalent alloying additions are only expected to have a significant effect on the oxidation resistance of Alloy 800 if they favour the formation of breakthrough duplex ...

Energy Technology Data Exchange (ETDEWEB)

Dominating factors in plasma nitriding and plasma condition that makes nitriding possible in plasma nitriding process of metals having hard oxide film were studied. In case of stainless steel, oxide film sputtering was easier comparing to nitriding layer. Three phenomena such as sputtering of oxide layer, formation of nitriding layer and sputtering of nitriding layer occurred simultaneously. Nitriding was achieved when the formation of nitriding layer reached the peak comparing to the removal of nitriding layer after the removal of oxide layer. Situations of metallic surface of stainless steel in surface nitriding were divided into four categories and they were, situation where oxide layer remained as it is, situation where nitriding layer was formed although oxide layer remained in some part, situation where only nitriding layer was formed and situation where ...

Science.gov (United States)

A laboratory-scale well-mixed thermostatic reactor with continuously blasting air was used to investigate the oxidation inhibition of sulfite in dual alkali flue gas desulfurization (FGD) system. The effects of operating parameters such as pH value and catalyst concentration on the oxidation were studied. Sodium thiosulfate was used in the system, and was found that it significantly inhabited the sulfite oxidation. In the absence of catalyst, sodium thiosulfate at 12.67 mmol/L had an inhibition efficiency of approximately 98%. While in the presence of catalyst, sodium thiosulfate at 26.72 mmol/L had an inhibition efficiency less than 85.0%. The oxidation reaction order of sulfite in the sodium thiosulfate was determined to be -1.90 and -0.55 in the absence and presence of the catalyst, respectively. Apparent activation energy of oxidation inhibition was calculated to be 53.9 kJ/mol. ...

Energy Technology Data Exchange (ETDEWEB)

Boron is implanted in crystalline silicon through oxide layers with different thicknesses. The implantation is carried out at various doses and energies of interest in ultra large scale integration (ULSI) application. Rapid thermal annealings (RTA) are used to obtain shallow junctions and electrical activation of the B atoms. However, transient enhanced diffusion induced by implantation damage can be observed. The boron concentration profiles before and after annealing are obtained with secondary ion mass spectrometry (SIMS). It is found that the diffusion transient in the tail region of the boron profile increases with decreasing oxide thickness. Even more, if the implantation damage concerns mostly the oxide, i.e. when the concentration peak is located in this oxide, the oxygen knocked into the silicon substrate could play this way an important role in restricting the boron diffusion, which is good to ...

International Nuclear Information System (INIS)

Because of the environmental hazard of organic solvents such as chlorinated or aromatic hydrocarbons, water soluble and biodegradable substitutes have come into use. It should be assessed how they affect soil and aquifer when spilled in leaks or accidents. This was simulated in a model system using methanol and percolation columns, one filled with material from the unsaturated subsurface and two with different materials from aquifers. The results reveal that a spill of the substitutes can also cause problems. In homogeneous soils and at long retention times until the substance reaches the aquifer, sorption and biological degradation are most likely to prevent contamination of the groundwater. When oxygen supply in the subsurface is insufficient, reducing conditions occur and sulphide is formed. The data show that much more methanol was eliminated than reflected by the consumption of electron acceptors. This indicates that sorption and anabolic turnover of the microorganisms play an ...