International Nuclear Information System (INIS)

In situ spectroscopic ellipsometry was employed to investigate the initial regime of rare earth metal (REM) conversion coatings formation on AZ31 magnesium alloy. Three REM salts solutions, 0.05 mol.dm"-"3 Ce(NO_3)_3, La(NO)_3 and Sm(NO)_3 solutions, were used for REM conversion coatings preparation. By deconvoluting the ellipsometric data, the surface of the fresh well-polished AZ31 magnesium alloy was found to be covered with 15.80 nm thick native (hydr)oxide film; the refractive indices and the thickness of Ce, La and Sm conversion coatings were obtained. The formation kinetics of three REM coatings follows different exponential functions and the coatings exhibit different optical properties. La conversion coating has the largest n values and the lowest k values while Sm conversion coating is just opposite. Moreover, the pH variation of the bulk conversion solutions upon the coatings formation was recorded. It is ...

International Nuclear Information System (INIS)

The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples.

International Nuclear Information System (INIS)

Short communication.

International Nuclear Information System (INIS)

This patent describes the producing of a refractory metal wherein a sponge refractory metal is produced as an intermediate product by the use of magnesium with the incidental production of magnesium chloride, and wherein residual magnesium is separated from the magnesium chloride and from refractory metal to a vacuum distillation step which fractionally distills the magnesium, the magnesium chloride, and the metal sub-chlorides; the steps of: recovering fractionally distilled vapors of magnesium chloride and metal sub-chlorides from a sponge refractory metal; separately condensing the vapors as separately recovered; and recycling the separately recovered magnesium at a purity of at least about 96%.

International Nuclear Information System (INIS)

This document generates a supernatant hydroxide ion depletion model based on mechanistic principles. The carbon dioxide absorption mechanistic model is developed in this report. The report also benchmarks the model against historical tank supernatant hydroxide data and vapor space carbon dioxide data. A comparison of the newly generated mechanistic model with previously applied empirical hydroxide depletion equations is also performed.

UK PubMed Central (United Kingdom)

Fasting plasma concentrations of magnesium were measured by neutron activation analysis in 30 non-diabetics and 87 diabetics (55 non-insulin-treated, 32 insulin treated). Plasma concentrations of magnesium...Full Text Available

International Nuclear Information System (INIS)

The intercalation reaction of some layered transition metal disulfides with alkali metals, alkali metal hydroxides, and tetraalkylammonium hydroxides were investigated. The alkali metal intercalates were prepared in the respective metal-hexamethylphosphoric triamide solutions in vaccuo, and the hydroxide intercalates in aqueous hydroxide solutions. According to the intercalation reaction, the c-lattice parameter was increased, and the increase indicated the expansion of the interlayer distance. In the case of alkali metal intercalates, the expansion of the interlayer distance increased continuously, corresponding to the atomic radius of the alkali metal. On the other hand, the hydroxide intercalates showed discrete expansion corresponding to the effective ionic radius of the intercalated cation. All intercalates of TaS_2 amd NbS_2 were superconductors. The expansion of the ...

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Wastenet

as a by-product during the purification of molten magnesium chloride prior to its electrolysis and during the

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

KoreaScience (Korea)

Full Text Available

Science.gov (United States)

The extraction of magnesium by tributyl phosphate from KI solutions was investigated. With increasing KI and TBP concentrations, the extraction increased. The maximum extraction (82%) was attained at pH 4, and it did not decrease with a further pH increase. With decreasing pH, the extraction decreased because of HI extraction. The magnesium was extracted as the compound MgI/sub 2/ x 4TBP. Complexone III (at pH 3-4) does not affect the extraction of magnesium, which makes it possible to use it to mask other metals.

Energy Technology Data Exchange (ETDEWEB)

Two extruded magnesium alloys, AZ31 and AZ61 were selected to evaluate the influence of process parameters on the material forgeability. The processing parameters considered for forging magnesium alloys were: compression load in the range 55 KN to 60 KN and forging temperature, in the range of ambient temperature to 300 C. Uniaxial compression tests were conducted to establish the strain-temperature relationship. The influences of process parameters on the microstructure were also evaluated. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Measurements of the double-electron-capture process in which a positive ion of iodine becomes a negative ion in a single collision with a magnesium atom are reported between 20 and 90 keV. The cross section is comparable to that for the rare gases and not as large as might be expected from a two-valence-electron atom. This process is probably insignificant in the production of negative ion beams using a magnesium-vapor target.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are being increasingly utilized in a variety of fields as an alternative material to organic materials and aluminum alloys, owing to excellent properties. Those include low density, and excellent damping properties. When compared to organic materials, furthermore, Mg alloy excels at recyclability, heat radiation, and electromagnetic-shielding. Though most of magnesium alloy products are manufactured through die-casting and thixo-molding at present, the demand for the expanding of magnesium wrought alloy market is increasing. Taking full advantage of a drawing technique and applying it to the conventional extruded pipe, we have developed a new type of magnesium alloy pipe. The strength of the developed pipe is significantly higher than that of the conventional one, either extruded or die-casting. Some of the excellent properties were obtained from fundamental tests performed with the ...

Energy Technology Data Exchange (ETDEWEB)

The oxidation of Cr(III) hydroxides, mixed Fe(III)-Cr(III) hydroxides, and specimens of spinel phases NiCr2O4 and Fe(Cr,Fe)2O4 have been investigated in alkaline suspensions under the action of air and pure oxygen (1-3 atm). The rate of reaction increases with increasing alkali concentration, temperature, and oxygen pressure. Pu(IV) fixed on chromium hydroxides is not oxidized by oxygen under these conditions but is retained in the precipitate.

International Nuclear Information System (INIS)

An experimental approach has been performed to ascertain the effectiveness of semi-solid strip casting using a horizontal twin roll caster. The demand for light-weight products with high strength has grown recently due to the rapid development of automobile and aircraft technology. One key to such development has been utilization of magnesium alloys, which can potentially reduce the total product weight. However, the problems of utilizing magnesium alloys are still mainly related to high manufacturing cost. One of the solutions to this problem is to develop magnesium casting-rolling technology in order to produce magnesium sheet products at competitive cost for commercial applications. In this experiment, magnesium alloy AZ31B was used to ascertain the effectiveness of semi-solid roll strip casting for producing magnesium alloy sheets. The temperature of the ...

Science.gov (United States)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +/- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +/- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

Energy Technology Data Exchange (ETDEWEB)

Aluminum hydroxide coating thicknesses were measured on fuel elements stored in aluminum canisters in K West Basin using specially developed eddy current probes . The results were used to estimate coating inventories for MCO fuel,loading. Brushing tests successfully demonstrated the ability to remove the coating if deemed necessary prior to MCO loading.

Energy Technology Data Exchange (ETDEWEB)

The goal of this work was to develop a process flow diagram to economically produce a clean-burning fuel from fine Illinois coal. To accomplish this, the process of pelletizing fine coal with calcium hydroxide, a sulfur capturing sorbent, was investigated. Carbonation, which is the reaction of calcium hydroxide with carbon dioxide (in the presence of moisture) to produce a bonding matrix of calcium carbonate, was investigated as a method for improving pellet quality and reducing binder costs. Proper moisture level is critical to allow the reaction to occur. If too much moisture is present in a pellet, the pore spaces are filled and carbon dioxide must diffuse through the water to reach the calcium hydroxide and react. This severely slows or stops the reaction. The ideal situation is when there is just enough moisture to coat the calcium hydroxide allowing for the reaction to proceed. The process has ...

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium is known to have poor formability at room temperature, mainly attributed to its hexagonal lattice structure. This paper presents the findings generated from development of warm forming to produce thin-walled magnesium components. Finite element analysis was conducted to evaluate the formability of the material and the simulated results were compared to the tensile results and product formability. Tensile tests were used to verify the formability of the sheet metal at difference temperatures. The process parameters considered in the feasibility study were forming temperature, in the range of 28 C to 300 C and magnesium sheet (AZ31B-H24) thickness, in the range of 0.4 mm to 1 mm. Magnesium hand phone covers of a thickness down to 0.4 mm have been successfully produced. The feasible forming temperature was found to be between 200 C and 250 C. Metallographic examination shows evident of ...

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

Science.gov (United States)

... alloys--Lanthanum-- Magnesium--Magnasium &11oy8--Hagn*31Uft compounds--Manxganese--Manganes. alloys-- Mercury ...

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are ...

International Nuclear Information System (INIS)

One of the major concerns during high speed welding of magnesium alloys is the presence of porosity in the weld metal that can deteriorate mechanical properties. This study seeks to analyze the presence method and quantity of pore during hybrid laser-tungsten inert gas arc (TIG) welding of magnesium alloy AZ31B by radiography, optical microscopy and electron probe microanalysis (EMPA). At the same time, it identifies both the mechanism of pore formation and a remedy for this problem. The experimental results indicate that lacking of shielding gas for laser beam is the dominant cause of macroporosity formation during the hybrid of laser-TIG welding of magnesium Alloys AZ31B plate, and hydrogen is not main cause to form large pores. A favorable weld without porosity can be obtained by appending lateral shielding gas for laser beam.

Energy Technology Data Exchange (ETDEWEB)

In this paper, for an acceleration of utilization of magnesium alloy which is being interested in recent years, friction welding of AZ31 magnesium alloy was carried out, and the joint performance was discussed in relation to the deformation heat input in the upset stage and upset loss as a evaluation factor. Where, the deformation heat input in the upset stage is mechanical work represented by the product of upset speed and axial pressure. As a result, it was made clear that the friction welding of AZ31 magnesium alloy was easy in the atmosphere, and good welded joints without a non- adhesion area at the weld interface could de obtained. Moreover, the evaluation factors discussed were possible to evaluate to joint performance. (orig.)

British Library Electronic Table of Contents (United Kingdom)

A microanalytical characterization of cast magnesium alloys of eutectic origin based on the Mg?Al?Ca ternary matrix system has been carried out in order to investigate the influence of alloying elements on their microstructure as well as microchemistry-processing-microstructural relations using structure-sensitive techniques of electron microscopy, mechanical spectroscopy (internal friction), X-ray diffractometry, and advanced microanalytical methods including electron probe compositional analysis. Following the data obtained here there is direct correlation of microstructure with creep properties of the new experimental magnesium alloys. The creep and heat-induced properties of the multicomponent magnesium alloys containing low range of inexpensive additions of titanium (0.07?0.2%) or str...

Energy Technology Data Exchange (ETDEWEB)

Although magnesium is not attacked by hydrocarbons, it reacts vigorously with anhydrous methanol, raising concerns about the compatibility of the metal with methanol blend fuels. This paper describes the behavior of magnesium alloys in laboratory tests in static contact with methanol-containing fuels at 110/sup 0/F. Water in small concentrations (above 0.25% by weight of the methanol content) is shown to prevent the destructive attack of magnesium by these fuels. The required water content is well within the water tolerance of methanol-GTBA (gasoline grade tertiary-butyl alcohol) cosolvent fuel blends. Die cast AZ91HP shows greater resistance to methanol reaction than does AZ31B sheet.

British Library Electronic Table of Contents (United Kingdom)

Magnesium fructose-1,6-diphosphate is a novel agent of antimyocardial ischaemia. In the present study, the subchronic toxicity of magnesium fructose-1,6-diphosphate was investigated after 13-week repeated intravenous administration in beagle dogs. The animals received doses of 0, 75, 150 and 300 mg/kg/day (three males and three females for each dose). During the study period, clinical signs, mortality, body weights, food consumption, electrocardiogram, urinalysis, haematology, clinical biochemistry, macroscopic findings, organ weights and histopathology were examined. The administration of magnesium fructose-1,6-diphosphate resulted in increased incidence of clinical signs, including salivation and emesis. These effects were transient and were noted in almost all dogs given 300 mg/kg/day a...

Energy Technology Data Exchange (ETDEWEB)

In order to investigate the extrusion characteristics of magnesium alloy (AZ31), a computer simulation was attempted. Tensile properties of as-cast billet with different strain rates were incorporated into the simulation. The results showed a great change in distribution of stress and strain at near die region by the ram travel. It was found that the average grain size at longitudinal edge of the extruded sheet was smaller than that at center region, which might be attributed to recrystallization caused by severe plastic deformation. (orig.)

International Nuclear Information System (INIS)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

Energy Technology Data Exchange (ETDEWEB)

PVD-chromium-nitride coated samples of substrates of the magnesium alloy AZ91hp and the roller and ball bearing steel 100Cr6 were investigated regarding structure, mechanical characteristics, adhesion and internal stresses. For the coatings the parameters layer thickness and substrate BIAS voltage were varied. Both substrate materials were coated in one lad. Results of the X-ray analysis of the internal stresses show significant differences between the coated magnesium and the coated steel substrates. In the case of the variation of the substrate BIAS voltage, for the coated steel a dependency of the internal stresses to coating parameters could be obtained. For the coated magnesium no dependency was recognizable. The coating structure was examined with scanning electron microscopy. Element depth profiles of the coated samples were performed with SIMS. (orig.)

UK PubMed Central (United Kingdom)

Strong aqueous ammonium hydroxide used to remove N-acyl protecting groups from synthetic oligoribonucleotides causes removal of some alkylsilyl protecting groups from 2'-hydroxyls and leads to chain...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

A process is claimed for selectively preparing alpha-olefins having from 2 to about 22 carbon atoms by contacting a gaseous mixture containing carbon monoxide and hydrogen with an iron titanate alkali metal hydroxide catalyst at reaction conditions correlated so as to favor the formation of a substantial proportion of such alpha-olefin product.

International Nuclear Information System (INIS)

The influence of microalloying vanadium or titanium on improving the corrosion resistance of mild steel in saturated calcium hydroxide solution was investigated. Potential-time, potentiodynamic polarization, and impedance measurement techniques were employed. The corrosion products have been examined by infrared and X-ray diffraction analysis and by scanning electron microscopy. It has been shown that the grain refining, due to microalloying, plays an important role in enhancing the corrosion resistance of steel. Scales of calcite and iron oxides on top of a protective oxide are formed on the investigated steels.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are ideal candidates to benefit from equal channel angular extrusion (ECAE) because of their poor forming characteristics due to a hcp structure. In this study, ECAE processing was applied to ZK31 and AZ31 magnesium alloys under various conditions. The grain size of as-ECAE specimens decreases with decreasing the processing temperature, however, the grain size decreases slightly with increasing number of repetitive processing. Both the tensile strength and 0.2% proof stress of as-ECAE specimens are high when processed at low temperature, but the elongation is high when processed at high temperature. Crystal orientation is different in the two alloys and it also varies according to the processing temperature for the two alloys. The difference of the crystal orientation influences the tensile properties, especially 0.2% proof stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Passive films were formed on chromium by polarization at +400 mV/SHE in 0.5 M H{sub 2}SO{sub 4} for different times (30 minutes, 2 hours and 20 hours) without and with chlorides. The effect of chlorides was studied by adding NaCl to the solution before or after passivation. The chloride concentrations were 0.05, 0.3 and 1 M. The (i-E) curves recorded for Cr without and with Cl{sup -} are similar and the addition of chlorides after passivation has no significant effect on the current recorded in the passive state. The passive films were analyzed by angle-resolved XPS (AR-XPS). The measurements performed at different take-off angles of the photoelectrons show that the films have a bilayer structure constituted of an outer hydroxide layer, Cr(OH){sub 3}, and an inner oxide layer, Cr{sub 2}O{sub 3}. The thicknesses of the oxide and hydroxide layers are 3 A and 9 A, 6 A and 7 A and 6 A and 6 A for the films formed in 0.5 M H{sub 2}SO{sub 4} after 30 ...

International Nuclear Information System (INIS)

Hybrid organic-inorganic coatings with phosphonate functionalities have been synthesized and evaluated as prospective surface treatments for magnesium materials. These coatings have been processed via a sol-gel route by hydrolysis and condensation of a mixture of diethylphosphonatoethyltriethoxy-silane and tetraethoxy-silane with variable molar ratios. The coatings morphology and the surface chemistry at the coating/substrate interface have been characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, "3"1P nuclear magnetic resonance spectroscopy, and time-of-flight secondary ion mass spectrometry. The corrosion protection performance of the coatings deposited on magnesium alloy AZ31B has been examined by a group of electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, a scanning Kelvin probe technique has been used to investigate interfacial ...

Science.gov (United States)

... having high fluidity. The SC-51A alloy contains 4.5 to 5.5% silicon, 1 to 1.5% coppers .4 to .6% magnesium, o35% sine, .8% iron, .5% manganes*, ...

Science.gov (United States)

The effects of various fixative agents, pH, ionic strength, stain concentration, and magnesium concentration on DNA staining with the antibiotics olivomycin, chromomycin A3, and mithramycin were examined with DNA in solution and in mammalian cells.

Science.gov (United States)

The biocompatibility and corrosion resistance of various materials for use as sacrificial anodes in in vivo hybrid fuel cells were studied. Aluminium, zinc, and magnesium alloy AZ31B were studied, and the results are discussed.

Energy Technology Data Exchange (ETDEWEB)

Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

To investigate the influence of equal channel angular pressing on the microstructure and texture of the magnesium alloy AZ31, electron backscattering diffraction and well as neutron diffraction experiments were carried out. Through these experiments it was possible to trace the microstructure and texture evolution with strain accumulated with the increasing number of equal channel angular pressing passes. It was further demonstrated by subsequent compression tests that the microstructural changes produced by equal channel angular pressing have a beneficial effect on both the compressive strength and ductility of AZ31. (orig.)

International Nuclear Information System (INIS)

The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society

Energy Technology Data Exchange (ETDEWEB)

Semiconductor properties of passive films formed on the Fe-18Cr alloy in a borate buffer solution (pH = 8.4) and 0.1 M H{sub 2}SO{sub 4} solution were examined using a photoelectrochemical spectroscopy and an electrochemical impedance spectroscopy. Photo current reveals two photo action spectra that derived from outer hydroxide and inner oxide layers. A typical n-type semiconductor behaviour is observed by both photo current and impedance for the passive films formed in the borate buffer solution. On the other hand, a negative photo current generated, the absolute value of which decreased as applied potential increased in the sulfuric acid solution. This indicates that the passive film behaves as a p-type semiconductor. However, Mott-Schottky plot revealed the typical n-type semiconductor property. It is concluded that the passive film on the Fe-18Cr alloy formed in the borate buffer solution is composed of both n-type outer hydroxide and inner ...

Energy Technology Data Exchange (ETDEWEB)

The possibility of obtaining high yields of hydrogen through the exposure of calcium hydroxide to natural uranium fission fragments is confirmed experimentally. The amounts of hydrogen obtained in some experiments were determined not only from the mass-spectrometry data, but also with the use of standard chemical analysis methods. The radiolytic hydrogen yield averaged over six independent experiments comprises 20.41 hydrogen molecules per 100 eV of absorbed fission fragment energy. The corresponding energy efficiency makes up to 60.62. Since on interaction with water or water vapor calcium hydroxide enters into the exothermal reaction to liberate 15.6 kcal/mole, it can easily be regenerated; this was attested to by one of irradiation experiments. Therefore, in the long run, we are dealing with a radiolytic decomposition of water at low temperatures or at temperatures readily available with modern reactor engineering techniques. Comparison of ...

International Nuclear Information System (INIS)

A flame retardant tarpaulin is used for protecting equipments upon periodical repairing in places for handling radioactive materials such as a nuclear power plant. It is formed by coating a woven fabric, a knitted fabric or a non-woven fabric with from 100 to 1000% by weight of a composition formed by blending from 3 to 10 parts by weight of red phosphorus and from 7 to 25 parts by weight of melamine sulfate to 100 parts by weight of an ethylene-vinyl acetate copolymer having a vinyl acetate content of from 8 to 28% by weight. Further, it comprises metal hydroxides such as Mg hydroxide and Al hydroxide. Aids such as plasticizers, stabilizers, lubricants and colorants can optionally be blended so long as they do not inhibit the flame retardant effect. It has an excellent flame retardancy, and does not produce poisonous gases or a great amount of ashes when burnt and discarded. It can be processed with satisfactory ...

International Nuclear Information System (INIS)

Denting studies have been undertaken in order to assess the influence of the most important parameters which could initiate corrosion of the carbon-steel occurring in the tube-tube support plate crevices of some PWR steam generators. Tests have been carried out in model boilers, feedwater being polluted with sea or river water. Specific effect of chloride or sulfate and influence of oxygen content, magnetite addition and pH value were investigated. In magnetite prepacked crevices, denting is obtained within 1000 hours for sea-water pollution of 0.3 ppm chloride at the blowdown. In neutral chloride or in river water denting is observed only with oxygen addition. Denting prevention is effective in the case of an on-line addition of phosphate, boric acid or calcium hydroxide. For denting stopping, boric acid or calcium hydroxide is efficient even with a high sea-water pollution. Soaks cannot stop denting if they are not followed by an on-line ...

International Nuclear Information System (INIS)

Available in abstract form only. Full text of publication follows: In this study. simulation of carbon dioxide absorption by Sodium Hydroxide solution in a packed bed has been investigated. At first, mass and energy balances were applied around a differential height of the bed. So, the governing equations were obtained. Surface renewal theory by Danckwerts was used to represent the mass transfer operation Finally, by changing the operating parameters like solvent temperature, inlet gas composition pressure and height of the bed, the effect of these parameters on the absorption and the composition of carbon dioxide in exit stream have been investigated. (authors)

British Library Electronic Table of Contents (United Kingdom)

Co catalysts, obtained from a layered double Co?Zn?Al hydroxide, are highly active and stable towards the hydrogenolysis of glycerol to 1,2-propanediol (1,2-PDO) in aqueous media. The Co-673 catalyst, containing a CoO species, provided a glycerol conversion of 67.7% and a 1,2-PDO selectivity of 50.5%. The Co-873 catalyst comprising 16?nm Co nanoparticles gave a glycerol conversion of 70.6% and a 1,2-PDO selectivity of 57.8%. It was revealed that the CoO species in the Co-673 catalyst was readily converted to 50?nm Co particles under the glycerol hydrogenolysis conditions. The Co catalysts maintained a stable size and phase in recycling tests. Graphical Abstract

International Nuclear Information System (INIS)

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

Measurements of local mass fluxes of liquid, local number fluxes of the drop and local drop size distributions at various locations in the test column were made for wide ranges of liquid flow rates and gas flow rates. An empirical correlation for the volume mean diameter of the drop at the nozzle exit was proposed. Measurements of the rates of absorption of carbon dioxide from carbon dioxide-air mixtures with water sprays (physical absorption) and aqueous sodium hydroxide sprays (chemical absorption) were made for wide range so fluid flow rates, feed gas concentrations, and initial alkali concentrations. The observed dimensionless rates of absorption were compared with the theoretical values by assuming penetration model with second-order irreversible reaction. 11 refs., 7 figs.

British Library Electronic Table of Contents (United Kingdom)

A new heterogeneous catalyst for the esterification of free fatty acids and the transesterification of vegetable oils is reported. The layered compound zinc hydroxide nitrate (Zn5(OH)8(NO3)22H2O) was very effective in the alcoholysis of palm oil and the esterification of lauric acid with m(ethanol), even when hydrated ethanol was used. Over the range of 100-140degreeC, the ester yield was the highest at 140degreeC, while the catalyst concentration had a much greater effect on ester yields than the molar ratio of alcohol to acid did. Total ester contents above 95wt% were obtained in both reactions and 93.2wt% glycerin streams were recovered as a result of methanolysis.

Energy Technology Data Exchange (ETDEWEB)

Aluminum is a principal element in alkaline nuclear sludge waste stored in high level waste (HLW) tanks at the Savannah River Site. The mass of sludge in a HLW tank can be reduced through the caustic leaching of aluminum, i.e. converting aluminum oxides (gibbsite) and oxide-hydroxides (boehmite) into soluble hydroxides through reaction with a hot caustic solution. The temperature limits outlined by the chemistry control program for HLW tanks to prevent caustic stress corrosion cracking (CSCC) in concentrated hydroxide solutions will potentially be exceeded during the sludge mass reduction (SMR) campaign. Corrosion testing was performed to determine the potential for CSCC under expected conditions. The experimental test program, developed based upon previous test results and expected conditions during the current SMR campaign, consisted of electrochemical and mechanical testing to determine the susceptibility of ASTM A516 ...

International Nuclear Information System (INIS)

Crude N,N-dialkylcarbamoylmethylphosphonates and phosphine oxide extractants, and particularly crude dihexyl N,N-diethylcarbamoylmethylphosphonate and octylphenyl N,N-diisobutylcarbamoyl phosphine oxide, are purified by distilling the crude materials in a thin film evaporator. Preferably, the crude materials are reacted with concentrated hydrochloric acid and then with aqueous sodium hydroxide prior to distillation in the thin film evaporator to hydrolyze impurities contained in them. The purified extractants are useful for extracting actinides and lanthanides from liquid waste streams. (author).

Energy Technology Data Exchange (ETDEWEB)

Hydrothermal method for preparing crystal borophosphate with zeolite structure is suggested. To increase absorption capacity and thermal stability of final product, aluminium hydroxide sol, ethylenediamine and ethyl acetate are added to the mixture of crystal boric and concentrated phosphoric acids. Thermal stability of the specimens prepared constitutes 880-950 deg, water absorption capacity is within the limits of 0.30-0.32 cmT/g. 1 table.

UK PubMed Central (United Kingdom)

Fresh-harvested, air-dried rice straw was pretreated at a water content of 5 g H₂O/g straw using sodium hydroxide (NaOH) and compared to pretreatment at 10 g H₂O/g...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

A press formability of magnesium alloy sheet cannot be evaluated by only general characteristics in tensile test; tensile strength, elongation n-value and r-value. For example, AZ31-alloy elongates about 20% in room temperature but breaks easily at shallow stage in deep drawing, which is caused by little local elongation (local necking). Crystallographic restriction of slip deformation in this alloy produces high strength, which almost equal to macroscopic fracture strength. In press forming, the bending under high tension requires a large deformability. A great difference in the deformability between AZ31 magnesium alloy and a strain hardened A1100 Aluminum (only 5% in elongation) is shown by static bending test with V-notch. In a rolled plate of AZ31, a crack is produced by stress concentration and propagates with reduced load at all testing temperature up to 453 K. In contrast, the point of notch in A1100 is dulled by local plastic ...

International Nuclear Information System (INIS)

Research highlights: ? Reports a high protection system for the alloy in corrosive environment. ? Describes an interfacial process with self-healing properties. ? Reports the influence of substrate pre-treatment in the coating performance. - Abstract: In this paper the interface of poly(vinylidene fluoride) coatings prepared by the dip coating method and HF-treated AZ31 magnesium alloy was evaluated. The best performance of this system in corrosion tests compared to ground, as-received and acetic acid cleaned substrates is related to an acid-base interaction at the interface and to interfacial reactions which resulted in a self-healing process. The protectiveness of the samples was investigated using impedance and immersion tests while the coating morphology and interface stability were investigated by scanning electron microscopy, X-ray photoelectron spectroscopy and adhesion tests.

Energy Technology Data Exchange (ETDEWEB)

AZ31 magnesium alloy was friction-welded to AM60 and the microstructures and the friction welding process were studied. The microstructures changed near the weld interface. The AZ31 was refined to a grain size of several {mu}m near the weld interface. The nucleation occurred in the shear bands that were introduced during the welding process. On the other hand, the eutectic structure was deformed and the lamellar structure which was composed of {alpha}-Mg and Mg{sub 17}Al{sub 12} was formed near the weld interface in AM60 alloy. In the friction process, the adhesion and peel off occurred alternately between AZ31 and AM60. Eventually, bonding was completed during upset process. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The development of a twinned microstructure in hexagonal close-packed rolled magnesium compressed in the in-plane direction has been monitored in situ with neutron diffraction. The continuous conversion of the parent to daughter microstructure is tracked through the variation of diffraction peak intensities corresponding to each. Approximately 80% of the parent microstructure twins by 8% compression. Elastic lattice strain measurements indicate that the stress in the newly formed twins (daughters) is relaxed relative to the stress field in the surrounding matrix. However, since the daughters are in a plastically 'hard' deformation orientation, they quickly accumulate elastic strain as surrounding grains deform plastically. Polycrystal modeling of the deformation process provides insight about the crystallographic deformation mechanism involved.

Energy Technology Data Exchange (ETDEWEB)

Grain refinement in AZ31 magnesium alloy has been attempted by hot-rolling and annealing process. Specimens were solution heat treated at 673 K for 36 ks, then hot-rolled at 423-773 K with total reduction of 20-80% by multi pass process. The rolled specimens were annealed at 473-673 K for 3.6 ks. Grain sizes after the solution heat treatment were about 20 to 150 {mu}m. After hot-rolling at 573 K and annealing at 473 K, grain sizes decreased into about 5 to 10 {mu}m. Suppression of grain growth by pinning due to precipitates was observed by transmission electron microscopic observations. (orig.)

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and ...

Science.gov (United States)

A number of alloys of zirconium have been investigated as part of a program aimed at improving the high-temperature tensile and creep strength of zirconium. These alloys include aluminum, beryllium, lead, magnesium, molybdenum, niobium, tantalum, tin, titanium, tungsten, vanadium, and zinc, binary and ternary alloys. The data indicate that aluminum, lead, molybdenum niobium, tin, titanium, tungsten, and vanadium can be used successfully to harden zirconium, and that aluminum, tin, titanium, and vanadium are particularly effective in maintaining the strength of zirconium at elevated temperatures.

Energy Technology Data Exchange (ETDEWEB)

Nutrient elements contained in litter fall flux, that of uptake flux and turnover rate had generally tended to increase with the increase in the Warmth Index, while the amount of nutrient in the A[sub 0] horizon and nutrient use efficiency did not. However, it is suggested that topographic and climatic aridity, and the amount of available and exchangeable phosphorus, calcium and magnesium greatly affect the nutrient dynamics in a each forest ecosystem as the Warmth Index increases. (J.P.N.).

International Nuclear Information System (INIS)

Dynamic recrystallization (DRX) is the main softening mechanism of magnesium alloy AZ31B in hot deformation. Theoretically, in the flow rule the atomic diffusibility and the driving force of dislocation migration are dependent on the temperature, and the dislocation density and the cumulation of grain boundary energy are dependent on the strain rate. The peak stress will appear when the flow driving force and resistance force reach a balance, after which the stress descending will take place due to recrystallization fraction. Since the DRX is a thermally activated process, the recrystallized volume fraction can be regarded as the function of strain through Avrami equation. Based on this idea, the paper proposes a new constitutive model characterizing dynamic recrystallization for magnesium alloy AZ31B. The model is described by a peak stress and a strain softening rate, in which the peak stress depends only on Zener-Hollomon parameter and is ...

International Nuclear Information System (INIS)

Austenitic stainless steels have been implanted with molybdenum ions (Mo"+, 100 keV, 2.5 x 10"1"6 atoms cm"-"2). The implanted material has been characterized by XPS and RBS. The implanted region has a thickness of #approx# 1000 A with a maximum molybdenum concentration of #approx# 9 at.% Mo located at #approx# 210 A from the surface. The effects of implanted molybdenum on the passivation of the alloy in 0.5 M H_2SO_4 have been investigated by electrochemistry and XPS. After XPS analysis the samples were transferred without exposure to air into a glove-box with an inert atmosphere. The electrochemical behaviour of the alloy is significantly modified by the implanted molybdenum. The major effect is that the activation peak disappears. A bilayer structure (outer hydroxide/inner oxide) of the passive film is observed for both the implanted and non-implanted alloys and the thicknesses of the films are similar. On the implanted alloy the outer ...

Energy Technology Data Exchange (ETDEWEB)

This patent describes a process for preparing of an ion exchanger, comprising: treating an ionically inert activated charcoal porous support with an aqueous solution of metal oxychloride selected from the group consisting of zirconium and titanium oxychlorides so as to impregnate the pores of the support with the solution; separating the treated support from excess metal oxychloride solution; converting the metal oxychloride to a hydrous metal oxide precipitate in the pores of the support at a pH above 8 and above the pH whereat the hydrous metal oxide and activated charcoal support have opposite zeta potentials and sufficient to hydrolyze the metal oxychloride. It also describes a process for preparing an ion exchanger comprising: treating granulated activated charcoal with a concentrated solution of a metal oxychloride from the group consisting of zirconium and titanium oxychlorides, degassing the mixture; and treating the resultant mixture with a base selected from the group ...

Energy Technology Data Exchange (ETDEWEB)

Apparatus and methods are described for generating heat and electricity from the consumption of a variety of aluminum products. The method consists of (A) a reaction chamber containing an aqueous electrolyte solution and adapted for introduction therein of aluminum pieces of various shapes and sizes up to a certain maximum predetermined size and for effecting a chemical reaction between said aqueous electrolyte and said aluminum pieces yielding aluminum hydroxide and an intermediate reactant; (B) means for feeding said aluminum pieces into said reaction chamber in small quantities upon demand; (C) means for removing the heat generated in said chamber as a result of said reaction; (D) means for removing said aluminum hydroxide reaction product; and (E) means for oxidizing said intermediate reactant in an electrochemical cell, thereby generating electrical energy. The intermediate reactant is preferably hydrogen or zinc. The latter may be used in ...

Energy Technology Data Exchange (ETDEWEB)

Constant extension rate (CERT) tests were performed on Alloy 690 and Alloy 800 nuclear steam generator tubing specimens. For the Alloy 690 specimens, tests were performed in deaerated 10% sodium hydroxide solutions at 315 deg C with a +100 mV applied potential. For the Alloy 800 specimens, tests were performed in deaerated 5% sodium hydroxide solutions at 343 deg C with no applied potential. The test specimens were machined from tubing which was produced by different manufacturing processes and in different heat treated conditions. The Alloy 690 tubing was tested in six different thermomechanical conditions, while the Alloy 800 tubing was tested in four different thermomechanical conditions. The results from the test program include a complete microstructural examination using light-optical and scanning electron microscopy. The CERT test results (such as maximum stress achieved and crack morphology) are correlated to tubing microstructure, ...

International Nuclear Information System (INIS)

This paper presents the results of experimental study carried out to know whether the salicylic acid used as an additive during the precipitation of zirconium using ammonium hydroxide solution goes into the filtrate, remains in the hydrated zirconia or gets distributed between the both under the ambient conditions of precipitation. Keeping its simplicity and amenability to adopt on a routine basis, spectrophotometric method has been chosen for the purpose among the many methods available and the problems associated in determining salicylic acid in the presence of zirconium and the medial measures to circumvent the same have been brought out in detail. (author)

Energy Technology Data Exchange (ETDEWEB)

Two new surfactant molecules are reported which contain thermally labile Diels-Alder adducts connecting the polar and non-polar sections of each molecule. The two surfactants possess identical non-polar dodecyl tail segments but exhibit different polar headgroups. The surfactants become soluble in water when anionic salts are formed through the deprotonation of the surfactant headgroups by the addition of potassium hydroxide. When either surfactant is exposed to temperature above about 60.degree. C., the retro Diels-Alder reaction occurs, yielding hydrophilic and hydrophobic fragments or the aqueous solutions of the surfactants subsequently exhibit loss of all surface-active behavior.

Energy Technology Data Exchange (ETDEWEB)

'The interactions of carbon tetrachloride with strongly basic oxides and hydroxides have been studied by several techniques in order to understand the surface reactions and the subsequent bulk reactions that result in the destruction of the chlorinated hydrocarbon. Emphasis has been placed on understanding the surface phases, as well as the bulk phases, that are present during these transformations. As a result of the study with barium oxide, a reaction cycle has been demonstrated that may have practical significance in the removal of chlorinated hydrocarbons.'

International Nuclear Information System (INIS)

In this study, Multi-Walled Carbon Nanotubes (MWCNTs) / Hydroxylapatite (HAp) composites were made to improve mechanical properties by using Spark Plasma Sintering (SPS) method. Slurry 6 mol of CaHPO4#centre dot#2H2O (DCPD), 4 mol calcium hydroxide and MWCNTs were mixed and sintered by using SPS at 5-120 MPa pressure, 1200-1250 deg. C and in vacuum or N2 atmosphere. The fracture toughness of sintered MWCNTs/HAp composites was increased.

Energy Technology Data Exchange (ETDEWEB)

This work is the first active crossflow filter testing of the new strontium-permanganate process for Envelope C at the Savannah River Technology Center. Extreme filtration difficulties with the ferric hydroxide precipitation led to investigations of other chemistries with simulants. The current process includes the isotopic dilution by precipitation from inactive strontium nitrate addition. A permanganate strike to replace ferric reagents was found to provide practical filterability and good lanthanide or transuranic decontamination. That work had been supported with simulant and active beaker testing.

British Library Electronic Table of Contents (United Kingdom)

Uranium has varying degrees of oxidation (+4 and +6) and is responsive to changes in the redox potential of the environment. It is deposited at the reduction barrier with the participation of biota and at the sorption barrier under oxidative conditions. Iron (hydr)oxides are the strongest sorbents of uranium. Uranium, being an element of medium biological absorption, can accumulate (relative to thorium) in the humus horizons of some soils. The high content of uranium in uncontaminated soils is most frequently inherited from the parent rocks in the regions of positive U anomalies: in the soils developed on oil shales and in the marginal zone of bogs at the reduction barrier. The development of nuclear and coal-fired power engineering resulted in the environmental contamination with uranium....

Energy Technology Data Exchange (ETDEWEB)

The structure of hydroxylated oxide films (passive films) formed on Cr(110) in 0.5 M H{sub 2}SO{sub 4} at +0.35, +0.55, and +0.75 V/SHE has been investigated by in situ scanning tunneling microscopy (STM). Cathodic reduction pretreatments at {minus}0.54, {minus}0.64, and {minus}0.74 V/SHE destroy the well-defined topography of the single-crystal electrode and they have been excluded from the passivation procedure. Two different passive film structures have been observed, depending on the potential and time of passivation. At low potential (+0.35 V/SHE), the passive film, consisting mostly of chromium hydroxide, has a noncrystalline and granular structure whose roughness suggests local variations of thickness of ca. {+-} 0.5 nm. A similar structure is observed at higher potential (+0.55 V/SHE), but only for a short polarization time. For longer polarization at 0.55 V/SHE, and at higher potentials (+0.75 V/SHE), a crystalline structure is formed; the higher the ...

Energy Technology Data Exchange (ETDEWEB)

The warm caliber rolling was experimented using the AZ31 magnesium alloy round bar of 20 mm in diameter machined from cast ingot materials. In warm caliber rolling in final size of 10 mm in diameter at 623 K via 8passes, each width-spreading, the change of each microstructure, X-ray analysis of final texture and final mechanical properties were investigated. Microstructure, texture and mechanical properties of warm caliber rolled round bar at 473 K via latter 4passes were compared with those at 623 K consistently. Obtained results are as follows: (1) The width-spreading in caliber rolling of round bar is relatively large, compared with that in flat rolling of the flat bar. The largeness of width-spreading of round bar makes the shape control of cross section difficult, and causes the cracks around the free surface. (2) Finer microstructure and inclined c axis of hexagonal lattice of 10 degrees to vertical direction of the rolled surface are obtained in warm caliber ...

Energy Technology Data Exchange (ETDEWEB)

Superplasticity of polycrystalline metallic materials is a phenomenon which shows hundreds to thousands of percents of large plastic deformation without necking in a steady state of low stress, when the uni-axial tensile loading is done in some special thermo-mechanical conditions (some limited ranges of properly high temperature and low strain rate). The main mechanism of superplastic phenomenon is the grain boundary sliding, while the main mechanism of usual plastic deformation is the trans-granular sliding. In this research, the possibility of superplastic deformation in a magnesium alloy (AZ31Mg alloy) was experimentally investigated, because generally speaking, the magnesium alloy whose atomic structure is hexagonal does not have enough formability in a form of trans-granular sliding mechanism. In this paper, the detail of experimental results are shown and discussed. Moreover, the constitutive equations of Mg alloy are proposed on the ...

Energy Technology Data Exchange (ETDEWEB)

Our goal was a process to convert methane to higher hydrocarbons oxidatively, since this circumvents thermodynamic yield limits of a strictly degydrogenative process. Keller and Bhasin converted thermodynamic yield limits of a strictly dehydrogenative process. Keller and Bhasin converted methane to higher hydrocarbons by using metal oxides as oxidants, without co-fed oxygen. They stated that selectivity is necessarily poor if gaseous oxygen is present. Jones and Sofranko have also used reducible metal oxides as oxidants in a group of their parents, but later used some of those materials with continuous O{sub 2} feed without much loss of selectivity. Baerns, Lunsford and Otsuka have shown that high selectivity could be possible with co-fed O{sub 2} at least for low O{sub 2} partial pressures, over PbO-A1{sub 2}O{sub 3}, Li-MgO and rare earths. The performance of a group of multicomponent oxide catalysts, containing lead and magnesium oxides, for oxidative conversion ...

Energy Technology Data Exchange (ETDEWEB)

Three kinds of thin AZ31 wrought magnesium alloys sheets were used in order to investigate the influence of the second phase particles on fracture toughness. From the theoretical model, the ratio of {lambda}{sub p}/d{sub p} would be estimated 5 {proportional_to} 6. On the other hand, from the microstructural observation, average particle spacing on each material was sample A: 13.1 {mu}m, sample B: 14.1, and sample C: 12 {mu}. In addition, average particle size on each sample was sample A: 2.1, sample B: 1.9, and sample C: 2.3 {mu}m. Therefore, the ratio of {lambda}{sub p}/d{sub p} calculated from fracture surface observation would be predicted 6 {proportional_to} 7. In comparison with the result of the prediction by theoretical analysis was in good agreement with the result of fracture toughness observation. It was found that the variation in plane-strain fracture toughness on AZ31 were affected by both of particle spacing and particle size. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The deformation behavior and structure changes of magnesium alloy AZ31 were studied in compression at temperatures ranging from 523 K to 673 K and at a strain rate of 3 x 10{sup -3} s{sup -1}. They depend sensitively on deformation temperature. At high temperatures, grain fragmentation takes place due to frequent formation of kink bands initially at corrugated grain boundaries and then in grain interiors, followed by full development of new grains in high strain. At lower temperatures, in contrast, twinning takes place in rather coarse grains and kink bands are formed mainly in finer original ones in low strain. It is concluded that new grain evolution can be controlled by a deformation-induced continuous reaction resulting in grain fragmentation by kink bands, i.e. continuous dynamic recrystallization (cDRX). The latter is discussed comparing with conventional, i.e. discontinuous, DRX. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The effect of ammonia treatment in field natural rubber (NR) latex with different storage period time on the properties of concentrated NR latex and stability of skim latex was investigated. Fresh NR latex was treated with various ammonia contents such as 0.35, 0.60 and 0.80% w/w, and then they were centrifuged to get the concentrated NR latex with 60% dry rubber content (DRC) containing 0.16, 0.18 and 0.25% w/w, respectively and skim NR latex with roughly 5% DRC containing 0.42, 0.60 and 0.80% w/w, respectively. The effect of storage times with ?0, 15, 30 and 45 days for concentrated NR latex with different ammonia contents on their properties such as alkalinity, magnesium content and viscosity was observed. It was found that generally, magnesium content in field NR latex and latex...

Energy Technology Data Exchange (ETDEWEB)

The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was also influenced by the test orientation. Metallographic studies revealed a ...

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

Energy Technology Data Exchange (ETDEWEB)

This specification establishes requirements for design, testing, and quality assurance for electric heaters that will be used to maintain primary Sodium temperature in the Fast Test Facility (FFTF) reactor vessel. The Test Specification (WHC-SD-FF-SDS-003) has been revised to Rev. 1. This change modifies the fabrication of approximately 25 feet of the subject heater using ceramic insulators over the heater lead wire rather than compressed magnesium oxide. Also, 304 or 316 stainless steel can be used for the heater sheath. This change should simplify fabrication and improve the heater operational reliability.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

International Nuclear Information System (INIS)

The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.

Science.gov (United States)

INTRODUCTION. We searched for a pathophysiologically based feature of major water electrolytes, which may define water quality better than the water hardness, respecting urinary calculus formation. MATERIALS AND METHODS. Utilizing a multistage stratified sampling, 2310 patients were diagnosed in the imaging centers of the provincial capitals in Iran between 2007 and 2008. These were composed of 1755 patients who were settled residents of 24 provincial capitals. Data on the regional drinking water composition, obtained from an accredited registry, and their relationships with the region's incidence of urinary calculi were evaluated by metaregression models. The stone risk index (defined as the ratio of calcium to magnesium-bicarbonate product in drinking water) was used to assess the risk of calculus formation. RESULTS. No correlation was found between the urinary calculus incidence and the amount of calcium, bicarbonate, or the total hardness of the drinking water. ...

International Nuclear Information System (INIS)

The extraction of rare earth elements, yttrium and aluminium from red mud resulting from alumina production with the ion-exchange resin KU-2-8n was studied. Experimental results are presented. The technology of hydrometallurgical processing of pulps obtained by sorption extraction of scandium from red mud is developed. It is shown that in the process of precipitation from sulfate sulfuric acid desorbate it became possible to obtain a high degree of rare earths deposition. The use of sodium hydroxide makes it possible to obtain a maximum deposition of rare earths and aluminium - 99.9 %. Aluminium leaching from crude composite concentrate gives a possibility to get concentrates which 15 - 20 times richer in yttrium and rare earths

British Library Electronic Table of Contents (United Kingdom)

A protective film has been developed on the surface of carbon steel in low chloride aqueous environment using a synergistic mixture of an environmentally friendly phosphonic acid, N,N-bis(phosphonomethyl) glycine (BPMG), and zinc ions. Impedance studies of the metal/solution interface indicated that the surface film is highly protective against the corrosion of carbon steel in the chosen environment. Potentiodynamic polarization studies showed that the inhibitor is a mixed inhibitor. X-ray photoelectron spectroscopic analysis (XPS) of the film showed the presence of the elements iron, phosphorus, nitrogen, oxygen, carbon, and zinc. Deconvolution spectra of these elements in the surface film showed the presence of oxides/hydroxides of iron(III), Zn(OH)2, and [Zn(II)-BPMG] complex. This infe...

Energy Technology Data Exchange (ETDEWEB)

Sulfuric acid hydrogen peroxide mixtures (SPM) are commonly used in the semiconductor industry to remove organic contaminants from wafer surfaces. This viscous solution is very difficult to rinse off wafer surfaces. Various rinsing conditions were tested and the resulting residual contamination on the wafer surface was measured. The addition of small amounts of a chemical base such as ammonium hydroxide to the rinse water has been found to be effective in reducing the surface concentration of sulfur and also mitigates the particle growth that occurs on SPM cleaned wafers. The volume of room temperature water required to rinse these wafers is also significantly reduced.

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy UNS N06690 were investigated in simulated crevice chemistries. It was found the role of lead in corrosion processes is strongly dependent on the pH value of the testing solutions. At pH 1.5 the effect of lead is narrowly noticeable; while at pH 12.7, lead has a significant influence on the electrochemical performance of alloy UNS N06690. The lead alters the surface morphologies at both pH and account for higher hydroxide content in the surface film at pH 12.7. The lead incorporation hinders the formation of spinel oxides during the passivation in alkaline solution. Nanoindentation tests indicate a significant lead-induced degradation in the mechanical properties of passive films. The passivation degradation is attributed to detrimental effects of lead via interrupting the dehydration process and hindering the formation of protective layers on the alloy surface.

Energy Technology Data Exchange (ETDEWEB)

A formulation to pelletize simulated high-level ICPP alumina waste calcine was developed. The pellets are formed on a 41-cm-diameter disc pelletizer using 5% bentonite, 2% metakaolin, and 5 wt % calcium hydroxide as a solid binder and a solution of 7M phosphoric acid and 4M nitric acid as a liquid binder. After drying and heat treatment at 800/sup 0/C for 2 hours, the average crush strength of the pellets is 3.9 MPa and the pellets have a leach resistance of 10/sup -3/ g/cm/sup 2//day, based on Soxhlet leaching for 48 h at 95/sup 0/C with distilled water.

Energy Technology Data Exchange (ETDEWEB)

Describes a process for production of briquets for metallurgy with binder and coke fines or anthracite. The suggested binder is waste phenol resin from the production of phenol (cumene method). Resin properties are given. Possible reaction mechanisms yielding solidified matter are discussed. The production process requires 10-15% binder and applies charge heating up to 200 C over 30 min. Catalytic amounts of sodium hydroxide or sulfuric acid were also employed. The production process is shown in a flowsheet. Properties of produced briquets are tabulated. The briquets were used in a 8 t/h cupola furnace and their performance was compared to that of KL-1 coke. Performance was found to be comparable; the cost of coke briquets was less than that of heating coke. 2 refs.

Energy Technology Data Exchange (ETDEWEB)

X-ray photoelectron spectroscopy and ex situ scanning tunneling microscopy measurements have been combined to investigate the thickness, the chemical composition, and the structure of passive films formed in 0.5 M H{sub 2}SO{sub 4} on Fe-22Cr(110). Aging under polarization at +500 mV/SHE causes a dehydration (anodic) reaction of the outer chromium hydroxide layer of the passive film. This anodic reaction results in a thickening of the inner mixed Cr(III) and Fe(III) oxide layer enriched in Cr{sub 2}O{sub 3}. It also causes a coalescence of the oxide nuclei of the passive film and a crystallization of the inner Cr{sub 2}O{sub 3}. It also causes a coalescence of the oxide nuclei of the passive film and a crystallization of the inner Cr{sub 2}O{sub 3} oxide layer in epitaxy with the substrate. The epitaxial relationship is {alpha}-Cr{sub 2}O{sub 3}(0001) {parallel} Fe-22Cr(110) with three different azimuthal orientations. Aging under polarization is beneficial to the ...

International Nuclear Information System (INIS)

Three model boilers, manufactured to simulate full-size tube sheet crevices, were tested with various secondary side environments. The first was faulted with organics representative of the decomposition of humic acid. The second was faulted with sodium carbonate and sodium hydroxide, while the third was faulted with sodium sulfate and sodium hydroxide. Each model contained seven tubes, which included Alloy 600 in the mill-annealed (MA) and thermally-treated (TT) conditions and Alloy 690 in the thermally-treated condition. Two models contained Alloy 800 tubes in the mill-annealed condition and one had Alloy 800 in the mill-annealed/cold-worked/glass-bead-peened condition. Two different sizes of tubesheet crevices were used in all model boilers. In the organics-faulted boiler, tubes of Alloy 600MA, Alloy 690TT and Alloy 800MA experienced no significant intergranular attack (IGA); however, the Alloy 600TT had intergranular attack (IGA) three to ...

International Nuclear Information System (INIS)

The large degree of confusion and many contradictions which are evident in the literature regarding the dioxo-uranium(VI)-hydroxide system has prompted the re-investigation of the hydrolysis of UO_2"2"- in aqueous media. The hydrolysis reactions of the uranyl ion have been investigated by potentiometric (pH)-, spectrophotometric- and conductometric titrations of uranyl chloride solutions with sodium hydroxide solutions. In all these titrations two clearly defined endpoints were obtained, indicating the predominance in solution of only a limited number of species. From a consideration of all the experimentally obtained data the following set of species was proposed to be present in significant concentrations in the pH range 0 to 12: UO_2"2"-, (UO_2)_2(OH)_2"2"-, (UO_2)_2(OH)_3"- and (UO_2)_9(OH)_1_9"-. By using the proposed set of species, a mathematical model of the uranyl-hydroxo system was developed with which the titration curves obtained by ...

International Nuclear Information System (INIS)

Bone images obtained by single exposure dual energy subtraction with computed radiography, a new image processing method, were evaluated for the detectability of calcification in lung nodules in both phantom and clinical studies. In the phantom study, five simulated nodules containing known and uniformly distributed amounts of calcium hydroxide were placed in a human chest phantom and images were obtained the following five techniques: 1) conventional radiography (CXR), 2) low kV conventional radiography (Low), 3) Fuji computed radiography (FCR), 4) bone images with conventional singles exposure energy subtraction (ES) and 5) bone image with fine single exposure energy subtraction (FES). The detectability of calcification in the simulated nodules was evaluated by six radiologists using ROC analysis and two-way analysis of variance. In the clinical study, images of 42 lung nodules (21 calcified lung nodules and 21 non-calcified nodules), in which calcification was ...

Energy Technology Data Exchange (ETDEWEB)

Electrodeposited Zn alloys with Fe group metals are known to be more resistant than pure Zn. However, the role of the corrosion products on the corrosion inhibition is not considered up to date. The aim of the present work was to examine the composition of corrosion products, which form on the Zn and Zn alloy surfaces under atmospheric corrosion conditions up to 3 year of exposure, trying to correlate it with the differences in their corrosion resistance. Zn corrosion products have been characterized by X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Corrosion film composition was determined to depend on the sample exposure she, as well on the coating type. During the initial exposure stages oxide film was found to be the principal reaction product (XPS data), which in marine station consists from hydroxide phase exceptionally, while in urban one, contain up to 6-12 % of oxide. Succeeding corrosion products (XRD data) in marine station consists ...

Energy Technology Data Exchange (ETDEWEB)

The precipitation of heavy metals as hydroxides is the standard technique for the decontamination of waste water streams polluted by these elements. On the other side, progress in research has been made concerning the biosorption onto dead biomass and bioprecipitation supported by physiologically active bacteria. As the aim of this study, a flexible strategy has been envisaged cleaning a waste water with definite heavy metal load underlying the process mentioned above. Suitable bacteria were enriched and the process was tested in a technical plant. As result, a very high efficiency of heavy metal elimination has been found. The field of application covered by the acquired process is identical with the whole range of the waste water streams polluted by heavy metals. In addition, a second stage may be necessary if there are any further contaminants to be removed. (orig.) [Deutsch] Bei der Reinigung von schwermetallhaltigen Abwaessern ist der derzeitige Stand der ...

International Nuclear Information System (INIS)

Heat capacities and densities of aqueous MgCl/sub 2/, CaCl/sub 2/, and SrCl/sub 2/ from the accompanying paper are combined with literature data up to 473 K to yield temperature-dependent equations by using the ion-interaction model of Pitzer. These heat capacity equations have been integrated to yield the enthalpy and the Gibbs energy. The enthalpy parameters for 298 K are evaluated in separate calculations using published high-temperature osmotic data as well as heats of dilution, while the Gibbs energy parameters for 298 K are taken from the literature. The range of validity of the final equations is described.

International Nuclear Information System (INIS)

By means of the light microscopy and by the measurement of the mechanical properties one investigated into the phase composition and the properties of Al-Mg-Ce and Al-Mg-Y system alloys. One plotted the isothermal cross sections of the mentioned systems under 430 and 275 deg C temperatures at up to 16% magnesium concentration and up to 0.7% yttrium concentration. One determined the yield limit and strength, the relative elongation of Al-Mg base hardened and deformed alloys containing 7.0-9.9% Mg and Ce, Y, Mn, Zr dopes upon ageing under 175, 200, 250 and 300 deg C temperatures within the ageing time ensuring the hardening maximum effect

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

International Nuclear Information System (INIS)

This pilot project was carried out for the purpose of testing methods for active biological monitoring. It covered a period of three years (until September 1994), including two years of exposure. The measurements served to determine pollutant levels in plants used as animal fodder and dust-borne heavy metal concentrations in different sites and, on this basis, to obtain indirect information on human exposure. Among others, the pilot project investigated the suitability of Italian rye-grass as a biological indicator for aluminium, arsenic, cadmium, cobalt, chromium, copper, iron, mercury, magnesium, manganese, nickel, lead, platinum, antimony, titanium, and zinc. (orig./GL).

British Library Electronic Table of Contents (United Kingdom)

Mineral carbonation is based on the reaction of carbon dioxide with metal-oxide bearing minerals, usually containing magnesium or calcium silicate, to form hardly soluble carbonates and other solid byproducts. The concept is based on acceleration of the naturally occurring rock weathering process. In the present work the calcium silicate is present in the mineral, wollastonite. To accelerate the process and make it potentially useful for practical applications, mineral carbonation is conducted here using an indirect two-step route in which the reactive component (Ca^2^+ ions in considered case) is first extracted from the mineral matrix and afterwards carbonated. Two solid byproducts are formed in this process: silica in the extraction step and calcium carbonate in the carbonation step. In...

International Nuclear Information System (INIS)

AM-SC1 is a heat treatable magnesium alloy that has been specifically developed to achieve the elevated temperature strength and creep properties necessary for engine block applications. This paper describes the interrelationship between the microstructure and the mechanical properties of AM-SC1. The compressive and tensile strengths are relatively insensitive to temperature up to and including 450 K and the tensile yield behaviour deviates from a standard Hall-Petch relationship at grain sizes below 200 ?m. The microstructural features contributing to the creep resistance are both inter- and intra-granular in nature and are on length scales from nanometers to micrometers. The creep behaviour at 423 K and 450 K is diffusion controlled, with any contribution from the grain boundaries being negligible.

Energy Technology Data Exchange (ETDEWEB)

Materials for the construction of cold neutron sources must satisfy a range of demands. The cryogenic temperature and irradiation create a severe environment. Candidate materials are identified and existing cold sources are briefly surveyed to determine which materials may be used. Aluminum- and magnesium-based alloys are the preferred materials. Existing data for the effects of cryogenic temperature and near-ambient irradiation on the mechanical properties of these alloys are briefly reviewed, and the very limited information on the effects of cryogenic irradiation are outlined. Generating mechanical property data under cold source operating conditions is a daunting prospect. It is clear that the cold source material will be degraded by neutron irradiation, and so the cold source must be designed as a brittle vessel. The continued effective operation of many different cold sources at a number of reactors makes it clear that this can be accomplished. 46 refs., 8 ...

Energy Technology Data Exchange (ETDEWEB)

In the present study, element interdiffusions at the cofired interface of 9/1 Ag/Pd electrode and lead magnesium niobate (PMN)-based ferroelectrics were investigated using Auger Electron Spectroscopy (AES). Intense interdiffusions at the interface were observed while Ag and Pd could penetrate into the ceramics for about 1 {mu}m. Ag-doping experiments were carried out to further study the effects of Ag diffusion on electrical properties of the ceramics. The results showed that Ag could be incorporated into solid solution of the ceramics as Ag{sup +}. As a whole, the Curie temperature (Tc) and dielectric constant of the ceramics decreased with Ag addition. However, Ag addition had no obvious effect on the insulation resistivity. The results inferred that Ag{sup +} could substitute for Pb{sup 2+} at A site of ABO{sub 3} lattice, thereby oxygen vacancies were generated.

International Nuclear Information System (INIS)

The microstructure of commercial rolled magnesium alloy AZ31B (nominal composition Mg-3Al-0.9Zn-0.15Mn in wt.%) was investigated with the help of light microscopy, electron backscatter diffraction (EBSD) and X-ray diffraction technique after annealing in the temperature range from room temperature (RT) to 400 deg. C. Tensile tests at RT were performed to show the influence of the microstructure on mechanical properties. Static recrystallization (SRX) was observed during annealing of as-received alloy at and above 150 deg. C. Twins play an important role during SRX and serve as nucleation sites and preferred paths for growth of grains. The strong basal texture caused by rolling was weakened by SRX. Significant differences in the stress strain curves were observed for as-received and annealed specimens.

International Nuclear Information System (INIS)

The grain size dependence of the tensile properties and the deformation mechanisms responsible for those properties are examined for Mg alloy, AZ31B, sheet. Specifically, the Hall-Petch effect and strain anisotropy (r-value) are characterized experimentally, and interpreted using polycrystal plasticity modeling. {1 0 . 2} extension twins, {1 0 . 1} contraction twins, and so-called 'double-twins' are observed via microscopy and diffraction-based techniques, and the amount of twinning is found to increase with increasing grain size. For the sheet texture and tensile loading condition examined, {1 0 . 2} extension twinning is not expected, yet the polycrystal plasticity model predicts the observed behavior, including this 'anomalous' tensile twinning. The analysis shows that the Hall-Petch strength dependence, of the polycrystal as a whole, is primarily determined by the grain size dependence of the strength of the prismatic slip systems.

Energy Technology Data Exchange (ETDEWEB)

The structure and catalytic properties of 2 wt.-% Pd/SiO/sub 2/ catalysts promoted with 2 wt.-% MgO and 0.2-5 wt.-% iron have been investigated. Catalysts were characterized by TPR, hydrogen chemisorption, and Moessbauer spectroscopy and their catalytic performance in methanol formation was also measured. At 16 at.-% iron a sharp maximum was observed in the activity which can be interpreted as being due to simultaneous promotion with iron and MgO. Independent mechanisms of promotion were found for the two modifiers: iron influenced the metallic component by forming bimetallic PdFe particles while MgO changed the properties of silica in a favourable way. 6 figs., 29 refs., 1 tab.

International Nuclear Information System (INIS)

The study was conducted during 2000 to determine the role of various chemical plant factors viz., total minerals, nitrogen, fat contents, carbohydrate, macro an micro nutrients in the leaves of five genotypes of sugarcane i.e., BF-162, SPSG-26, L-118, CP-43/33 and CP-72/2086 by correlating the infestation of top borer, Scirpophaga Nivella F. at tillering stage. None of the genotype was found completely resistant to the pest. CP-43/33 and BF-162 proved susceptible and resistant varieties, respectively. Total mineral, manganese and copper contents did not show significant correlation with the pest infestation, whereas nitrogen, potassium, calcium, magnesium and ferrous contents played a positive and significant role. Phosphorous, carbohydrates, fats and zinc contents played a significant and negative effect on the pest infestation at tillering stage. (author)

Energy Technology Data Exchange (ETDEWEB)

Adsorpt1on of CH[sub 4] and coadsorption of CH[sub 4] and CO on differently treated magnesium oxide have been studied by FT-IR spectroscopy at 173-273 K. Five IR bands at 3008, 3000, 2900, 2890, and approximately 1306 cm[sup [minus]1] were observed when well-outgassed MgO was exposed to CH[sub 4] at 173 K. The bands at 3008 and 3000 cm[sup [minus]1] are assigned to a degenerate stretch vibration of CH[sub 4], and those at 2900 and 2890 cm[sup [minus]1] originate from an infrared-forbidden mode at 2917 cm[sup [minus]1] of free CH[sub 4]. These bands became noticeably stronger with the outgassing temperature of MgO but could be sufficiently reduced as MgO was pretreated in air or under water vapor. Adsorbed CO on MgO gives two IR bands at 2161 and 2155 cm[sup [minus]1] which exhibit a parallel variation with those bands of adsorbed CH[sub 4] with the different pretreatments of MgO. Coadsorption of CH[sub 4] and CO indicated that adsorbed CO can deplete part of the ...

Energy Technology Data Exchange (ETDEWEB)

''S-220'' white oil is used currently to impregnate and fill high voltage cables for 110-500 kilovolts; it has high electrical characteristics and meets production and use standards. High pressure and cooling problems, however, require filling cables with lower viscosity oils, while insulation needs still demand high viscosity. The authors developed a new white oil similar to S-220 using a neutral oil made in producing sulfonate additives. The process involved vacuum distillation, low-temperature paraffination, sulfation with oleum, neutralizing with ammonium hydroxide and simultaneous extraction of sulfo-salts and contact purification. The lowest content of aromatic hydrocarbons was sought. Dielectric qualities varied with viscosity. Satisfactory thermooxidational capability was found at 50/sup 0/C with an oil of no less than 50 mm/sup 2//sec viscosity. The final white oil had no more than 2% aromatic hydrocarbons, thus assuring ...

International Nuclear Information System (INIS)

There is renewed interest in the +6 oxidation state of iron, ferrate (VI) (FeVIO42-), because of its potential as a benign oxidant for organic synthesis, as a chemical in developing cleaner ('greener') technology for remediation processes, and as an alternative for environment-friendly battery cathodes. This interest has led many researchers to focus their attention on the synthesis of ferrate(VI). Of the three synthesis methods, electrochemical, wet chemical and thermal, electrochemical synthesis has received the most attention due to its ease and the high purity of the product. Moreover, electrochemical processes use an electron as a so-called clean chemical, thus avoiding the use of any harmful chemicals to oxidize iron to the +6 oxidation state. This paper reviews the development of electrochemical methods to synthesize ferrate(VI). The approaches chosen by different laboratories to overcome some of the difficulties associated with the electrochemical synthesis of ferrate(VI) are ...

Energy Technology Data Exchange (ETDEWEB)

Red mud is a waste product of the aluminium refining industry. It is composed of aluminium hydroxide and iron oxide. This study examined the feasibility of using red mud as a catalyst to eliminate volatile organic compounds in atmospheric pollutants. Volatile organic compounds can be eliminated by thermal oxidation between 600 and 1100 degrees C. However, the oxidation of volatile organic compounds can also be accomplished at lower temperatures (200 to 450 degrees C) if a catalyst is present. Currently, the low temperature destruction of volatile organic compounds is not widespread because of the difficulty in deactivating the catalyst. In this study, red mud was calcined in air at 500 degrees C. Under such conditions, the red mud converts to aluminium oxide and iron oxide. These 2 oxides are active and are carbon dioxide selective in the oxidation of volatile organic compounds. The study showed that red mud can be used as a catalyst for the oxidation of toluene. ...

Energy Technology Data Exchange (ETDEWEB)

In the framework of the feasibility study of radioactive waste disposal in deep geologic formations, a clay formation (named 'argilite de l'Est') has been selected in the Meuse-Haute Marne region (France) for the construction of an underground laboratory. The percolation of alkaline solutions through the argilite has been studied using column experiments with short residence times (30 min). These experiments simulate the leaching of a cement which could be used in the building materials of the laboratory. The alkaline solutions used are mono-cationic solutions of calcium, sodium and strontium. The behaviour of calcium is differentiated from the other cations. For all alkaline solutions (NaOH, Ca(OH){sub 2} or Sr(OH){sub 2}) chemical reactions consuming both hydroxide ions and their associated cations have been evidenced. These reactions are heterogenous reactions of surface adsorption by site ionization. The calcium has a different ...

Energy Technology Data Exchange (ETDEWEB)

The excellent high temperature strength and thermal conductivity of molybdenum-base alloys provide attractive features for components in advanced magnetic and inertial fusion devices. Refractory metal alloys react readily with oxygen and other gases. Oxidized molybdenum in turn is susceptible to losses from volatile molybdenum trioxide species, MoO{sub 3}(m), in air and the hydroxide, MoO{sub 2}(OH){sub 2}, formed from water vapor. Transport of radioactivity by the volatilization, migration, and re-deposition of these volatile species during a potential accident involving a loss of vacuum or inert environment represents a safety issue. In this report the authors present experimental results on the oxidation, volatilization and re-deposition of molybdenum from TZM in flowing air between 400 and 800 C. These results are compared with calculations obtained from a vaporization mass transfer model using chemical thermodynamic data for vapor pressures of MoO{sub 3}(g) ...

International Nuclear Information System (INIS)

Nanodimensional powders of cubic copper ferrite are synthesized by two-steps procedure of co-precipitation of copper and iron hydroxide carbonates, followed by mechanochemical treatment. X-ray powder diffraction, Moessbauer spectroscopy and temperature-programmed reduction are used for the characterization of the obtained materials. Their catalytic behavior is tested in methanol decomposition to hydrogen and CO and total oxidation of toluene. Formation of nanosized ferrite material is registered even after one hour of milling time. It is established that the prolonging of treatment procedure decreases the dispersion of the obtained product with the appearance of Fe2O3. It is demonstrated that the catalytic behavior of the samples depends not only on their initial phase composition, but on the concomitant ferrite phase transformations by the influence of the reaction medium. -- Graphical abstract: It is demonstrated that the catalytic behavior of the obtained copper ...

Energy Technology Data Exchange (ETDEWEB)

Two physical pre-treatment methods, particle size reduction by grinding and thermo-mechanical extrusion, were evaluated as alternatives to traditional biomass pretreatments for lignocellulosic ethanol. Commonly available agricultural co-products wheat bran and soybean hull were the model substrates. Extrusion led to higher reducing sugar yields as compared to grinding for wheat bran, but not in the case of soybean hulls. The best combination of extrusion screw speed and maximum barrel temperature were 7 Hz/150 C and 3.7 Hz/110 C. The use of a solvent mixture (sodium hydroxide, urea, and thiourea) and calcium chloride solution in combination with extrusion treatment did not lead to improvement in reducing sugar yield. However, extensive washing to get rid of solvents and enzymatic inhibitors improved the conversion efficiency substantially, resulting in total reducing sugar yields of 60-73% and 25-36%, respectively, for wheat bran and soybean hull. (author)

Energy Technology Data Exchange (ETDEWEB)

A sensitive and rapid automated method has been developed for the selective analysis of acid extractable sulfide in environmental samples by combining gas dialysis separation techniques with methylene blue detection procedures. Acid extractable sulfide is separated from the sample matrix by the gas dialysis membrane and subsequently trapped in a dilute sodium hydroxide receiving stream. This stream is reacted with N,N-dimethyl-p-phenylenediamine and ferric chloride to produce methylene blue which is then quantitated colorimetrically at 660 nm. For standards and nonturbid environmental samples, there is good agreement between the results obtained by this procedure and the standard methylene blue method. The effect of interferences on the accurate determination of sulfide by both methods was also examined and it was found that cupric ions significantly interfered with sulfide estimation. To obtain adequate sulfide recoveries in tap water and environmental samples ...

British Library Electronic Table of Contents (United Kingdom)

Ultra-fine ZnAl2O4 spinel hydrogel precursor synthesized from mixed salt solutions of Zn^2^+ and Al^3^+ ions using ammonium hydroxide-hexamethylenetetramine as basic media for co-precipitation was used as bonding material and sintering aid for pure alumina system. The hydrogel powder exhibited some well-defined ZnAl2O4 spinel phases at 800^oC. Alumina compacts were fabricated by incorporating small proportions of the precursor in alumina powder and firing at different temperatures (1350-1500^oC). The degree of densification was studied by measurement of fired shrinkage, apparent porosity, bulk density and cold crushing strength. Phase compositions and microstructural features of sintered samples were evaluated by XRD and SEM respectively. Addition of 0.2% hydrogel powder to alumina exhibit...

International Nuclear Information System (INIS)

The electrochemical behaviour of passive films formed on one austenitic stainless steel (AISI 304) and one ferritic stainless steel (AISI 446) in solutions with pH between 0.6 and 8.4 was studied by capacitance measurements and photocurrent spectroscopy. Compositional characterization of the passive films was done by X-ray photoelectron spectroscopy. The capacitance increases with decreasing pH. Doping densities evaluated from Mott-Schottky plots are in the range 2-6 x 10"2"0 cm"-"3 and increased with the pH in the neutral/alkaline range while in pH 0.6, values above 10"2"1 cm"-"3 were found. The bandgap energy indicates two transitions, at 2.5-2.8 and 3.2 eV. The analytical data reveal that, as the pH increased, the films become enriched in Fe(II) and Fe(III), whereas the Cr(III) gradually decreases. The films formed at very low pH had a behaviour that contrasts with that of the films formed in the neutral/alkaline media. The films are described by a bilayer structure, with ...

Energy Technology Data Exchange (ETDEWEB)

A stable isotope mass-balance of dissolved inorganic carbon during a blue-green algae bloom in a softwater lake demonstrates that at low partial pressure of carbon dioxide there must be a large net negative carbon isotope fractionation between atmospheric CO/sub 2/ and the CO/sub 2/ absorbed by lake water at pH = 9.5. Chemical enhancement of CO/sub 2/ invasion at high pH by the reaction CO/sub 2/ + OH/sup -/ ..-->.. HCO/sub 3//sup -/ at large apparent film thicknesses may result in carbon isotope fractionation approaching that for a hydroxide solution. This phenomenon, coupled with a decrease in the photosynthetic fractionation, forced the surface water of a softwater lake to achieve increasingly negative delta /sup 13/C values during an algal bloom, which is in the opposite sense to the trend that results from photosynthesis under less extreme conditions. This and other similar systems must operate under non-equilibrium (kinetic) conditions, causing a large ...

Energy Technology Data Exchange (ETDEWEB)

Basic experimental investigations were carried out with an aqueous solution of a mixture of KOH and NaOH for use as an absorbent in absorption heat pumps. Due to its thermophysical properties this mixture allows temperature lifts from evaporator to absorber of more than 75 K (135 F) in a single-stage absorption chiller. Thermophysical and hydrodynamical properties of the solution were measured. Vapor-liquid-equilibrium data and specific heat capacities were determined for concentrations ranging from 35% up to 75% and temperatures up to 200 C (392 F). From these data the enthalpy of the solution was calculated. Additionally the crystallization temperatures, the density, and the viscosity of the solution were determined. The experimental equipment is described. The data are presented as polynomials and diagrams including experimental accuracy. An apparatus was constructed to measure heat and mass transfer coefficients of the absorption process with this solution. The apparatus is a model ...

Energy Technology Data Exchange (ETDEWEB)

Full text of publication follows: Large-scale problems such as nuclear waste disposal are increasingly recognized to be interconnected to small scale-mechanisms. Thus, synchrotron-based high-resolution analytical X-ray probes become important tools for exploring the micro-scale chemical reactivity of heterogeneous barrier materials used in nuclear waste repositories. In this study the layout of the micro-XAS beamline at the Swiss Light Source (SLS) will be presented. The beamline is optimized towards micro beam experiments ({approx}1 x 1 {mu}m{sup 2}) in the hard-X-ray regime (4 - {approx}22 keV) and allows to combine micro X-ray fluorescence (micro-XRF), micro X-ray absorption spectroscopy (micro- XAS), and micro X-ray diffraction (micro-XRD) investigations with radioactive samples. Furthermore, the potential of micro-XRF/XAS/XRD for acquiring spatially resolved molecular level information on the speciation and structural coordination environment of radionuclides in heterogeneous ...

Energy Technology Data Exchange (ETDEWEB)

Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption was possible on minerals that are thought to have been transferred into coal ash. Compound indications of ashes from 29 kinds of the world`s typical ...

Energy Technology Data Exchange (ETDEWEB)

Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal surfaces for the ...

Energy Technology Data Exchange (ETDEWEB)

Theoretical investigations on the phase change materials (PCMs) used as the heat storage media for box-type solar cookers have been conducted in this study. The selected PCMs are magnesium nitrate hexahydrate, stearic acid, acetamide, acetanilide and erythritol. For a two-dimensional simulation model based on the enthalpy approach, calculations have been made for the melt fraction with conduction only. Different materials such as glass, stainless steel, tin, aluminum mixed, aluminum and copper are used as the heat exchanger container materials in the numerical calculations. The large value of thermal conductivity of heat exchanger container material did not make a significant contribution on the melt fraction except for at very low thermal conductivities. Based on the theoretical results, stearic acid and acetamide are found to be good compatibility with latent heat storage system. It is also found that the initial temperature of PCM does not have very important ...

Science.gov (United States)

As with mammalian enzymes, green crab (Scylla serrata) alkaline phosphatase can be activated by Mg2+ through a time-dependent course. The activation is mainly a Vmax effect. Tsou's method was used to study the kinetic course of activation. The results show that the enzyme was activated by a complexing scheme that had not been previously identified: the enzyme first reversibly and quickly binds Mg2+ and then undergoes a slow reversible course to activation, with a relatively high activation energy (78 +/- 4 kJ/mol) and a slow conformational change. The activation reaction is a single molecule reaction, and the apparent activation rate constant is independent of Mg2+ concentration if the concentration is sufficiently high. The microscopic rate constants of activation and the association constant were determined from the measurements. The proposed scheme may also be applied to the Mg2+ activation mechanism for mammalian enzyme, to explain why the activation rate is time-dependent and not ...

Science.gov (United States)

Appendices to this summary consist of twelve individual status reports that will be available through the National Technical Information Service (NTIS) in the United States and of course limited copies will be available through NATO. The twelve report titles which are appendices to the summary are: (A) Status Report on the Limestone/Sludge Flue Gas Desulfurization Process; (B) Status Report on the Lime/Sludge Flue Gas Desulfurization Process; (C) Status Report on the Double Alkali/Sludge Flue Gas Desulfurization Process; (D) Status Report on the Sea Water Scrubbing Flue Gas Desulfurization Process; (E) Status Report on the Limestone/Gypsum Flue Gas Desulfurization Process; (F) Status Report on the Lime/Gypsum Flue Gas Desulfurization Process; (G) Status Report on the Double Alkali/Gypsum Flue Gas Desulfurization Process; (H) Status Report on Flue Gas Desulfurization by Scrubbing with Dilute Sulfuric Acid; (I) Status Report on the Magnesium Oxide Flue Gas ...

Energy Technology Data Exchange (ETDEWEB)

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride <0.05 M containing 30% ethylene glycol solution, they are more corrosive than the blank (30% ethylene glycol-70% water). However, at concentrations <0.05 for chloride or >0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy ...

British Library Electronic Table of Contents (United Kingdom)

The effects of anthropogenic (nitrogen fertilization) and natural [soil texture, pH content of humus, ammonium nitrogen (N-NH4), and the available forms of phosphorus (P), potassium (K), magnesium (Mg)] factors on nitrate nitrogen (NO3-N) content and distribution were shown. The dependencies between these factors and the content of NO3-N in soil were estimated in three soil layers: 0-30 cm; 31-60 cm; 61-90 cm. The research was carried out in 2004-2006, and the soil samples were taken from 411 places throughout eastern Poland in two seasons: spring and autumn. The concentration of NO3-N significantly depended on the year of investigation, season of the year, and depth of sampling. Distribution of NO3-N in the soil profile indicates possibility of NO3 leaching during winter and early spring....

Energy Technology Data Exchange (ETDEWEB)

The cost of transporting biogas digestate can be decreased by reducing its water content. However, the digestate emits volatile compounds during drying. This study investigated the drying behaviour and the change of digestate composition. Drying took place in a hybrid solar/waste-heat dryer that used solar energy as well as waste heat from a combined heat and power unit (CHP) and the exhaust air of a microturbine. The experiment involved the use of 60 t of liquid digestate. Climatic conditions were measured inside and outside the drying hall. Dry matter (DM) and organic dry matter (ODM) were also measured on a daily basis. In addition, the energy consumption of waste and solar heat were recorded and related to the quantity of dried feedstock. The total nitrogen, ammonium, phosphate, potassium oxide, magnesium oxide and calcium oxide in the digestate were subjected to chemical analysis before and after the drying process. Losses of nitrogen were calculated. Specific ...

International Nuclear Information System (INIS)

The difference of NH_4"+-N/NO_3"--N nutrition between hybrid and conventional rice varieties at the late growth stage was studied by using "1"5N-tracer technique. The results showed that the nitrate fertilizer utilization efficiency by the hybrid rice after anthesis was 7.8% higher than that by the ordinary rice variety, and the nitrate fertilizer recovery fraction by the former was 13.2% greater than that by the latter. The varietal difference in NO_3"--N uptake and utilization was almost twice as that in NH_4"+-N. It was also showed that "1"5N distribution in ear of the hybrid rice was about 20% greater than that of the conventional variety, but there were no obvious differences between NO_3"--N and NH_4"+-N. However, "1"5N distribution in the lower node leaves and root was found to be significant higher with NO_3"--N than that with NH_4"+-N in both rice varieties, particularly in the hybrid rice. Compared with NH_4"+-N, NO_3"--N top-dressing before anthesis was observed to have much ...

Energy Technology Data Exchange (ETDEWEB)

Singlet oxygen generators are multiphase flow chemical reactors used to generate energetic oxygen to be used as a fuel for chemical oxygen iodine lasers. In this paper, a theoretical model of the generator is presented along with its solutions over ranges of parameter space and oxygen maximizing optimizations. The singlet oxygen generator (SOG) is a low-pressure, multiphase flow chemical reactor that is used to produce molecular oxygen in an electronically excited state, i.e. singlet delta oxygen. The primary product of the reactor, the energetic oxygen, is used in a stage immediately succeeding the SOG to dissociate and energize iodine. The gas mixture including the iodine is accelerated to a supersonic speed and lased. Thus the SOG is the fuel generator for the chemical oxygen iodine laser (COIL). The COIL has important application for both military purposes--it was developed by the US Air Force in the 1970s--and, as the infrared beam is readily absorbed by metals, industrial cutting ...

International Nuclear Information System (INIS)

Austenitic stainless steels (304-type) have been implanted with nitrogen ions in order to investigate the effects of implanted nitrogen on their electrochemical behaviour and on the nature of the passive film formed on the steels in acid (0.5M H_2SO_4). Alloys with two nitrogen doses have been prepared (2.5x10"1"6 and 2x10"1"7 N atoms/cm"2). The implanted alloys have been characterized by "1"5N-NRA (nuclear reaction analysis) and XPS (X-ray photoelectron spectroscopy). Alloy surfaces with well-defined N concentrations were prepared, prior to the electrochemical measurements, by argon-ion sputtering of the implanted material for a fixed time in order to reach a well-defined point on the nitrogen depth profile. The samples were then transferred without exposure to air to an electrochemical cell mounted in an inert gas glove box. The implanted nitrogen modifies the electrochemical behaviour of the alloy. The anodic dissolution in the active state is enhanced, and the current density in ...

International Nuclear Information System (INIS)

The interaction of Np(V), Pu(VI) and Tc(VII) with metal reductants Zn, Cr, Sn and their alloys was investigated in 0.5-4 mol l"-"1 NaOH solutions in static and dynamic conditions (by filtration of solutions through the column filled with grains of metal). In this paper, it was found that the reduction and succeeding precipitation hydroxides of these elements, on the surface of metal grains from 0.5 to 4 mol l"-"1 NaOH solutions, gives a decontamination factor (DF) from 1.1 to 67. The best result was achieved for Pu (DF=67) on Cr grains after 2.5 h contact at 60 C with 0.5 mol l"-"1 NaOH solution containing Pu(VI). Increasing the NaOH concentration, and the addition of chromate ions and complex-forming agents to alkaline solution results in a decrease of the decontamination factor (DF). A better result for Np sorption from 1 mol l"-"1 NaOH solutions was achieved after longer contact, than for Pu, with Cr and Zn grains. The maximum DF=8.9 was achieved for Tc on a ...

Energy Technology Data Exchange (ETDEWEB)

This human investigation of lead absorption from the lungs utilized two forms of lead, lead chloride and lead hydroxide; the former was used in picogram amounts and the latter at microgram levels. These two species of lead were selected in an attempt to simulate the range of physicochemical properties found in atmospheric lead (urban air). Aerosols labeled with lead-203 were made of comparable aerodynamic size (MMAD 0.25 ..mu..m +- 0.1) by using sodium chloride as the deposition-determining aerosol. After brief, mouthpiece exposures, 17 subjects were followed by serial counting with a thoracic array of 12 2-in. scintillation detectors and two 2-in. leg counters, all coupled to single channel analyzers. Serial blood samples were also taken. The two exposure groups showed similar total deposition values (23 vs 26%) and the same biological retention halftimes, viz., 22.6 h. When the retention data were corrected for blood-borne /sup 203/Pb, the biological halftimes ...

Energy Technology Data Exchange (ETDEWEB)

A flexible battery is printed on paper by screen-printing a zinc/carbon/polymer composite anode on one side of the sheet, polymerising a poly(3,4-ethylenedioxythiophene) (PEDOT) cathode on the other side of the sheet, and applying a lithium chloride electrolyte between the two electrodes. The PEDOT cathode is prepared by inkjet printing a pattern of iron(III)p-toluenesulfonate as a solution in butan-1-ol onto paper, followed by vapour phase polymerisation of the monomer. The electrolyte is prepared as a solution of lithium chloride and lithium hydroxide and also applied by inkjet printing on to paper, where it is absorbed into the sheet cross-section. Measurements on a zinc/carbon-PEDOT/air battery in a similar configuration on a polyethylene naphthalate substrate shows a discharge capacity of up to 1.4 mAh cm{sup -2} for an initial load of 2.5 mg zinc, equivalent to almost 70% of the zinc content of the anode, which generates 0.8 V at a discharge current of 500 ...

International Nuclear Information System (INIS)

The ecological effects of acid mine drainage were investigated during the summer of 1993 on St. Kevin Gulch, a headwater stream near Leadville, Colorado. The stream currently receives acidic water from an abandoned mine. The pH downstream of the mine is between 3.5 and 4.5, and several metals exceed concentrations toxic to aquatic organisms. Zinc is present at especially high concentrations (1 to 10 mg/L) Furthermore, the stream bottom is covered with a thick layer of iron hydroxide precipitates. Effects on stream biota have been dramatic. Aquatic flora in the affected reach is limited to a green filamentous alga, Ulothrix subtilissima. Macroinvertebrate densities are significantly lower in the affected reach (mean = 99 indiv/m"2; SD = 88 indiv/M"2) compared to an upstream (pristine) reference reach (mean = 1,735 indiv/m"2; SD = 652 indiv/M"2). Functional processes were also studied in the stream. Net primary production (NPP) was measured during midday with ...

Energy Technology Data Exchange (ETDEWEB)

Exchange of hardness ions is important in enhanced oil recovery with chemical additives. In both micellar-polymer and caustic flooding processes, multivalent ions released from rock surfaces can interact with anionic surfactants, rendering them preferentially oil soluble and/or insoluble in water. Because hardness cations are sparingly soluble and precipitate in alkaline solutions, such solutions may be more efficient as surfactant flood preflushes than are softened brines. Multivalent ion precipitation may also occur in alkaline waterflooding. To permit design of such processes, this paper presents a chromatographic theory for simultaneous ion exchange with precipitation of divalent ions. Theoretical effluent histories and concentration profiles are presented for the cases of finite pulses and continuous injection of hydroxide ions into linear cores. Complete capture of the insoluble salt particles is assumed. Results are given for the case of instantaneous ...

Energy Technology Data Exchange (ETDEWEB)

US Department of Energy (DOE) Order 5820.2A (DOE, 1988) requires performance assessments on all new and existing low-level radioactive waste (LLW) disposal sites. An integral part of performance assessment is estimating the fluxes of radioactive gases such as radon-220 and radon-222. Data needs pointed out by mathematical models drive site characterization. They provide a logical means of performing the required flux estimations. Thorium-230 waste, consisting largely of thorium hydroxide and thorium oxides, has been approved for disposal in shallow trenches and pits at the LLW Radioactive Waste Management Site in Area 5 of the Nevada Test Site. A sophisticated gas transport model, CASCADR8 (Lindstrom et al., 1992b), was used to simulate the transport and fate of radon-222 from its source of origin, nine feet below a closure cap of native soil, through the dry alluvial earth, to its point of release into the atmosphere. CASCADR8 is an M-chain gas-phase radionuclide ...

International Nuclear Information System (INIS)

Statements about the dynamic processes of uptake, transport, and deposition of Ca and Mg in norway spruce and Scots pine are made in this paper. Concerning the storage of these elements it is shown that there are great differences in their functional importance in cell metabolism. There is evidence that the role of Mg in enzyme and protein metabolism is of far greater significance for the understanding of Mg-deficiency symptoms than its function as the central atom of the chlorophyll complexes. In regard to the transport and especially to the incorporation of Ca into the needles differences between species were evident, expressing the special status of pine among the gymnosperms. With increasing needle age an accumulation of Ca-oxalate crystals, which are physiologically inert, could be proved for the studied conifers. This was interpreted as a 'detoxication' from surplus Ca to hold constant the level of the physiologically active fraction. Accordingly, the low Ca-contents of yellowed ...

Energy Technology Data Exchange (ETDEWEB)

The first Russian reprocessing facility, known as RT-1 (located at PA-Mayak in Ural region) was started on the radiochemical plant base in 1977. Nowadays RT-1 is the sole operating reprocessing plant in Russia. The main features of RT-1 is its broad spectrum of reprocessing spent nuclear fuels (SNF). The following spent fuel types are reprocessed: -) SNF from PWR reactors (WWER-440) and FB reactor (BN-600); -) SNF of transport ship reactors; -) production reactors SNF; -) research reactor spent nuclear fuel. The world-known technological processes are used at RT-1, but there are the following distinctive features. First, the universality of the three technological lines which allows not only the reprocessing of various SNF kinds, but also to implement the combined reprocessing of some types of them. Secondly, extraction of neptunium during SNF reprocessing which is used to implement its separate storage and for radioisotope production. Thirdly, target enrichment of recycled uranium is ...

Energy Technology Data Exchange (ETDEWEB)

The pharmacology of the alpha-2 adrenoceptor of the human adipocyte was improved by using some new alpha-2 antagonists from different chemical families (imidazolines, benzazepines and benzofuroquinolizines) in biological and binding assays. Moreover, investigations were also carried out to define the binding properties of a new imidazolinic antagonist, RX821002 (2-(2-methoxy-1,4-benzodioxan-2yl)-2-imidazoline), which could be a potential radioligand. (3H)RX821002 binding was very rapid and reversible. Saturation isotherms indicated that (3H)RX821002 labeled, with high affinity, a homogeneous population of noninteracting binding sites with a mean Kd of 0.98 +/- 0.05 nM (n = 6). The binding of (3H)RX821002 on the human fat cell alpha-2 adrenoceptor displayed a specificity which is strictly similar to that obtained with (3H)rauwolscine and which is classical for an alpha-2 A adrenoceptor. The binding parameters of (3H)RX821002 were compared with those obtained with the classical alpha-2 ...

International Nuclear Information System (INIS)

It is well known that one of the main advantages of the high speed forming (HSF) processes is the improvement in the forming limits of the used materials.Using the Electromagnetic Forming (EMF) technology two materials have been tested with different mechanical and physical properties: the AA5754 aluminium and the AZ31B magnesium alloys.The EMF process principle can be described as follows: A significant amount of electrical energy is stored in a bank of capacitors which are suddenly discharged releasing all the stored energy. This electric discharge runs through a coil which generates an intense transient magnetic field. At the same time transient Eddy currents are induced in the electrically conductive part placed some millimetres far from the coil. Another intense magnetic field is generated due to those Eddy currents but on the opposite direction as the one generated by the coil. A big magnetic repulsion force is created between the part and the coil. This ...

International Nuclear Information System (INIS)

Manganese is a common contaminant of mine water and other waste waters. Due to its high solubility over a wide pH range, it is notoriously difficult to remove from contaminated waters. Previous systems that effectively remove Mn from mine waters have involved oxidising the soluble Mn(II) species at an elevated pH using substrates such as limestone and dolomites. However it is currently unclear what effect the substrate type has upon abiotic Mn removal compared to biotic removal by in situ micro-organisms (biofilms). In order to investigate the relationship between substrate type, Mn precipitation and the biofilm community, net-alkaline Mn-contaminated mine water was treated in reactors containing one of the pure materials: dolomite, limestone, magnesite and quartzite. Mine water chemistry and Mn removal rates were monitored over a 3-month period in continuous-flow reactors. For all substrates except quartzite, Mn was removed from the mine water during this period, and Mn minerals ...

Energy Technology Data Exchange (ETDEWEB)

The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metal alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy efficient processes and good manufacturability. ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium-based alloys are among the promising materials for hydrogen storage and fuel cell applications due to their high hydrogen content. In the present work, we investigated the hydrogen release/uptake properties of the Mg-Ti-H system. Samples were prepared from the mixtures of MgH{sub 2} and TiH{sub 2} in molar ratios of 7:1 and 4:1 using a high-energy-high-pressure (HEHP) mechanical ball-milling method under 13.8 MPa hydrogen pressure. Thermogravimetric analysis (TGA) showed that a relatively large amount of hydrogen (5.91 and 4.82 wt.%, respectively, for the above two samples) was released between 126 and 313 C while temperature was increased at a heating rate of 5 C min{sup -1} under an argon flow. The onset dehydrogenation temperature of these mixtures, which is 126 C, is much lower than that of MgH{sub 2} alone, which is 381 C. The activation energy of dehydrogenation was 71 kJ mol{sup -1}, which is much smaller than that of as-received MgH{sub 2} (153 kJ ...

Energy Technology Data Exchange (ETDEWEB)

The reverse micelle catalyst preparation method has been used to prepare catalysts on four supports: magnesium oxide, carbon, alumina- titania and steamed Y zeolite. These catalysts were not as active as a reference catalyst prepared during previous contracts to Union Carbide Corp. This catalyst was supported on steamed Y zerolite support and was impregnated by a pore-filling method using a nonaqueous solvent. Additional catalysts were prepared via pore- filling impregnation of steamed Y zeolites. These catalysts had levels of cobalt two to three and a half times as high as the original Union Carbide catalyst. On a catalyst volume basis they were much more active than the previous catalyst; on an atom by atom basis the cobalt was about of the same activity, i.e., the high cobalt catalysts` cobalt atoms were not extensively covered over and deactivated by other cobalt atoms. The new, high activity, Y zerolite catalysts were not as stable as the earlier Union Carbide ...

Energy Technology Data Exchange (ETDEWEB)

To establish the optimum barium-based reduced-laxative tagging regimen prior to CT colonography (CTC). Ninety-five subjects underwent reduced-laxative (13 g senna/18 g magnesium citrate) CTC prior to same-day colonoscopy and were randomised to one of four tagging regimens using 20 ml 40%w/v barium sulphate: regimen A: four doses, B: three doses, C: three doses plus 220 ml 2.1% barium sulphate, or D: three doses plus 15 ml diatriazoate megluamine. Patient experience was assessed immediately after CTC and 1 week later. Two radiologists graded residual stool (1: none/scattered to 4: >50% circumference) and tagging efficacy for stool (1: untagged to 5: 100% tagged) and fluid (1: untagged, 2: layered, 3: tagged), noting the HU of tagged fluid. Preparation was good (76-94% segments graded 1), although best for regimen D (P = 0.02). Across all regimens, stool tagging quality was high (mean 3.7-4.5) and not significantly different among regimens. The HU of layered ...

International Nuclear Information System (INIS)

A one-year study was conducted to determine the impacts of acid min drainage (AMD) on the Black Creek watershed in Wise County, Virginia. Water quality, metal content of sediment and water column, soil pH, macroinvertebrate assemblages, habitat assessment and toxicity testing were used to assess the impact in the watershed. A total of 22 sites in the creek and surrounding watershed were actively monitored. This included six primary sources of AMD. Conductivity measurements > 1,000 microhmos/cm were found at eight sites and pH was consistently below 6.0 at seven. Of six metals analyzed, magnesium was highest in the water column, ranging from 16.5 mg/L to 130 mg/L. Aluminum and iron were both elevated in the sediment with iron concentrations as high as 176,000 mg/kg. An increase in sediment metal concentrations was noted when progressing downstream in the creek. Of nine high wall and spoils areas sampled, soil pH was acidic in eight sites, ranging from 5.5 to 3.1. ...

Energy Technology Data Exchange (ETDEWEB)

As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress corrosion cracking susceptibility. The effects of lead contamination on the stress corrosion cracking ...

Energy Technology Data Exchange (ETDEWEB)

As part of a coordinated program, AECL is developing a set of tools to aid with the prediction and management of steam generator performance. Although stress corrosion cracking (of Alloy 800) has not been detected in any operating steam generator, for life management it is necessary to develop mechanistic models to predict the conditions under which stress corrosion cracking is plausible. Therefore, constant extension rate tests were carried out for Alloy 800 under various steam generator crevice chemistry conditions at applied potentials. These tests were designed to evaluate the stress corrosion cracking susceptibility of Alloy 800 under CANDU( steam generator operating conditions. Based on the experimental results, the recommended electrochemical corrosion potential/pH zone for Alloy 800 determined by electrochemical polarization measurements was verified with the respect of stress corrosion cracking susceptibility. The effects of lead contamination on the stress corrosion cracking ...

Energy Technology Data Exchange (ETDEWEB)

The rate of the oxygen-exchange reaction in an aqueous solution of a heterocyclic oxygen compound, 2,4,6-trimethylpyrylium perchlorate, was quantitated. The /sup 18/O isotope effect in /sup 13/C NMR spectroscopy affords a direct, continuous, and relatively simple analysis of the reaction and was used to obtain data on the incorporation of /sup 18/O from solvent H/sub 2//sup 18/O into the pyrylium salt. Due to the low solubility of this salt in aqueous solutions, 2,4,6-trimethyl(2-/sup 13/C)pyrylium perchlorate and 2,4,6-trimethyl(2,6-/sup 13/C/sub 2/)pyrylium perchlorate were synthesized to facilitate the acquisition of the data on an NTC-200 spectrometer operating at 50.31 MHz. Upon incorporation of /sup 18/O into the pyrylium salt, the /sup 13/C NMR signal of the directly bonded carbon atom is shifted upfield 0.038 ppm. A /sup 13/C isotope effect is also detected in the doubly /sup 13/C-enriched pyrylium salt where the /sup 13/C NMR signal for /sup 13/C-O-/sup 13/C appears 0.011 ppm ...

International Nuclear Information System (INIS)

Selenium (Se), zinc (Zn), magnesium (Mg), molybdenum (Mo) and vanadium (V) in 28 types of Egyptian common foodstuffs as well as drinking and irrigation water samples were determined using neutron activation analysis (NAA) and atomic absorption spectrometry (AAS). The samples were collected from 74 sites over 13 governorates as well as the Nile river, wells and tap water in the regions of the Nile Delta, Sinai, the east and west desert, and north and south Egypt. These trace elements were chosen according to international references, which show the close relationship of their deficiencies to immunity-related diseases. Calculation values of daily uptake per capita were made with the results of analysis. The results, as calculated per 100 g dry weight, showed that some Egyptian foods are rich in Se including such fish (0.94 #mu#g), sesame (0.88 #mu#g), beef meat (0.48 #mu#g), instant tea (0.42 #mu#g), mushroom (0.34 #mu#g) and eggs (0.3 #mu#g), whereas the vegetables ...

Energy Technology Data Exchange (ETDEWEB)

This report summarizes the research conducted during Budget Period One on the project ''Improved Natural Gas Storage Well Remediation''. The project team consisted of Furness-Newburge, Inc., the technology developer; TechSavants, Inc., the technology validator; and Nicor Technologies, Inc., the technology user. The overall objectives for the project were: (1) To develop, fabricate and test prototype laboratory devices using sonication and underwater plasma to remove scale from natural gas storage well piping and perforations; (2) To modify the laboratory devices into units capable of being used downhole; (3) To test the capability of the downhole units to remove scale in an observation well at a natural gas storage field; (4) To modify (if necessary) and field harden the units and then test the units in two pressurized injection/withdrawal gas storage wells; and (5) To prepare the project's final report. This report covers activities ...