Energy Technology Data Exchange (ETDEWEB)

Polycrystalline Al2O3, magnesium aluminate spinel (MgAl2O4), MgO, Si3N4, and SiC were irradiated with various ions at 200-450 K, and microstructures were examined following irradiation using cross-section TEM. Amorphization was not observed in any of the irradiated oxide ceramics, despsite damage energy densities up to {similar_to}7 keV/atom (70 displacements per atom). On the other hand, SiC readily amorphized after damage levels of {similar_to}0.4 dpa at room temperature (RT). Si3N4 exhibited intermediate behavior; irradiation with Fe{sup 2+} ions at RT produced amorphization in the implanted ion region after damage levels of {similar_to}1 dpa. However, irradiated regions outside the implanted ion region did not amorphize even after damage levels > 5 dpa. The amorphous layer in the Fe-implanted region of Si3N4 did not appear if the specimen was simultaneoulsy irradiated with 1-MeV He{sup +} ions at RT. By comparison ...

Energy Technology Data Exchange (ETDEWEB)

Material testing of SPF-sheet is usually done with coupon hot tensile testing. The optimum range of strain rates is determined with stepped strain tests. To overcome the problem of very few available testing facilities and time consuming and costly procedure, cone cup testing has been developed since long. This test can be generated directly in the workshop, no machining of samples is necessary and it is very much related to the real SPF-process. The analysis of suitable temperature and strain rate is done by simple measurement of resulting cone height. This paper describes a unique and novel variant of the above mentioned baseline design. It provides on-line data of the actual status of the cone cup forming resulting from the applied, constant pressure. Strain rate variations as a result from texture or from the alloy-related behaviour is detectable. Thinning and ''hardening'' behaviour of different alloys up to maximum failure strain can be ...

Energy Technology Data Exchange (ETDEWEB)

Lithium-ion batteries are becoming more and more important not only for portable electronic devices, but also in prevision of high power electric vehicles. In such an optic, deep studies regarding all the components of a secondary battery are in development. In this study, high voltage cathode materials have been selected. Crystals with spinel structure have a 3D vacancy pathway suitable for Li-ions transport. The material under study was LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} doped with magnesium replacing the nickel. Various samples were synthesized via three different routes: a solid-state method, a modified sol-gel method and a xerogel method. The structure and morphology of the powders were analyzed with HRTEM and XRD. Electrochemical tests were also performed. A wide range of particle sizes (from micro to nanosize) was the result of the different synthesis routes. Unfortunately pure materials were not always obtained. The electrochemical tests ...

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Science.gov (United States)

PMID:21846114

Energy Technology Data Exchange (ETDEWEB)

Most waste water treatment plants have processes to remove nutrients in order to avoid eutrophication in water receiving bodies. Regarding phosphorus removal. the most common option is chemical precipitation with ferric or aluminical precipitation with ferric or aluminium salts. We show here the successful experience carried out by the WWTP of Blanes and the company Safloc. A method ato remove phosphorus from waste water was developed by adding sodium aluminate. The use of this compound has turned out to be a sustainable way for this purpose in terms of costs, reliability and minimization of sludge production. (Author)

UK PubMed Central (United Kingdom)

Fasting plasma concentrations of magnesium were measured by neutron activation analysis in 30 non-diabetics and 87 diabetics (55 non-insulin-treated, 32 insulin treated). Plasma concentrations of magnesium...Full Text Available

Energy Technology Data Exchange (ETDEWEB)

Using commercial AZ31 magnesium alloy sheets, we produced a foamable preform sheet containing titanium hydride (TiH{sub 2}) powder through diffusion-bonding and hot-rolling of four cycles. Heating the preform sheets in Ar atmosphere, we obtained closed-cell magnesium alloy foams with various porosities. The foamed specimen at 883 K showed the maximum porosities of 77%. (orig.)

Energy Technology Data Exchange (ETDEWEB)

No abstract prepared.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys show a high specific strength and are therefore increasingly used for light-weight constructions in transportation industry.{sup [1,2]} To predict the behaviour of the material under the influence of cyclic loading it is vital to understand the fatigue behaviour of magnesium alloys. Only when understood properly, it is possible to fully apply the potential weight reduction by using magnesium alloys. A very important aspect in fatigue of magnesium alloys is the influence of a corrosive media and elevated temperatures, of which both are relevant in automotive applications. These two factors tend to have deleterious effects on magnesium alloys and therefore also have to be considered in investigations on the fatigue behaviour of magnesium alloys. (Abstract Copyright [2004], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Purification parameters of the vacuum distillation process for AM50A and AZ31B magnesium alloy were studied. The vacuum distillation tests were kept at 580 C to 620 C up to 10 h under a vacuum pressure of about 1 Pa. The purification ratio for AM50A magnesium alloy increases with increasing the purification time. The chemical compositions of materials deposited purifying at 580 C for AM50A magnesium alloy almost satisfy the values for pure magnesium specified by JIS standard specification. The chemical compositions of deposited materials at 600 C for AZ31B magnesium alloy satisfy the values specified by the standard specification except for Zn. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Effects of rolling conditions on warm deep drawability of cast magnesium alloy that were hot rolled after roll strip casting were investigated to ascertain the feasibility of twin-roll strip casting process of AZ31B magnesium alloy. Hot rolling and heat treatment conditions were changed to examine which conditions were appropriate for producing AZ31B wrought magnesium alloys after strip casting process. Microscopic observation of the crystals of the manufactured wrought magnesium alloys was performed. It has been found that a limiting drawing ratio of 2.7 was possible in a warm deep drawing test of the cast magnesium alloy sheets after being hot rolled. (orig.)

UK PubMed Central (United Kingdom)

OBJECTIVE--To examine the effect of a reduced sodium and increased potassium and magnesium intake on blood pressure. DESIGN--Randomised double blind placebo controlled trial. SETTING--General population...Full Text Available

Science.gov (United States)

... Both magnesium and aluminium phosphides are therefore potentially more efficient than either calcium or sodium phosphide. ...

International Nuclear Information System (INIS)

Russian (1972). USSR Desyatnik, VN Kurbatov, NN Raspopin, SP Trifonov,

Energy Technology Data Exchange (ETDEWEB)

Two aspects of the deformation behavior of magnesium sheets are the subject of this paper. First it will give a mechanical characterization of a commercial magnesium with a focus on the anisotropy and the possible microstructural causes of this behavior. The rolling process will be part of the second aspect. The aim is to show the influence of the parameters on the microstructure and texture and how this could affect the anisotropy in the rolled sheets. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

The nature of interaction of some boromagnesium minerals with water is studied, the main stages of interaction are established. The methods of thermo-gravimetric, X-ray phase and chemical analyses are applied to state intermediate and final phases of magnesium borate interaction with water. ''Preobrazhenskite'' - ''inderite'' paragenesis is established. The notion ''magnesium borate solubility'' is shown to be senseless.

Energy Technology Data Exchange (ETDEWEB)

We present the synthesis, magnetic and UV spectrometry of NiZn-ferrite nanofiber. The single phase of spinel ferrite was obtained at 600 {sup o}C. The NiZn-ferrite fibers fabricated by an electrospinning process were formed as a polygonal grain growth with firing temperature in fiber matrix. It appeared that the saturation magnetization (M{sub S}) of NiZn-ferrite nanofiber was dependent on Ni/Zn molar ratio which is similar to that of the inverse spinel ferrites. The NiZn-ferrite fibers showed good DNA adsorption efficiency that can be modified and utilized for DNA separation with magnetic nanofiber as a novel material in clinical applications.

Energy Technology Data Exchange (ETDEWEB)

This paper deals with an experimental study of ultra-precision diamond cutting of magnesium alloy (AZ31). In order to investigate the machinability such as the cutting force and the surface integrity and understand the problems in a micro cutting, the experiments on the diamond cutting of magnesium alloy and pure aluminum with an ultra-precision turning machine has been carried out. The machinability of magnesium alloy was compared with that of pure aluminum and discussed. Consequently, both the thrust force component and the surface roughness obtained by cutting of magnesium alloy became larger than that of pure aluminum. It was also found that the inclusions or the defects in the work material caused to generate the scratches on the finished surface and influenced the integrity of mirror surface. (orig.)

International Nuclear Information System (INIS)

Slurry aluminizing is one method of protecting titanium alloys and intermetallics at temperatures at which oxidation would otherwise significantly degrade mechanical properties. The technique produces a continuous layer of alumina-forming TiAl_3 on exposed surfaces. The influence of composition, film thickness, and diffusion temperature upon the oxidation resistance of these slurry aluminides was studied in cyclic tests to 816degC (1500deg F). Degradation of slurry aluminized #beta#-titanium alloy and #alpha#-Z titanium aluminide intermetallic occurs by localized oxidation at cracks in the coating layer. These cracks are probably due to mismatch of coefficients of thermal expansion between the coatings and substrates. Addition of silicon to the slurry modifies the oxidation behaviour around a crack by introducing a continuous layer of titanium silicide at the boundary of the aluminide coating and substrate, thereby enhancing oxidation ...

Science.gov (United States)

We present a sample preparation method for measuring magnesium in individual whole lymphocytes by electron probe X-ray microanalysis. We use Burkitt's lymphoma cells in culture as the test sample and compare X-ray microanalysis of individual cells with atomic absorption analysis of pooled cell populations. We determine the magnesium peak-to-local continuum X-ray intensity ratio by electron probe X-ray microanalysis and calculate a mean cell magnesium concentration of 39 +/- 19 mmol/kg dry weight from analysis of 100 cells. We determine a mean cell magnesium concentration of 34 +/- 4 mmol/kg dry weight by atomic absorption analysis of pooled cells in three cell cultures. The mean cell magnesium concentrations determined by the two methods are not significantly different. We find a 10% coefficient of variation for both methods of analysis and a 30% coefficient of variation in ...

International Nuclear Information System (INIS)

The transmutation of minor actinides in-reactor is one solution currently being studied for the long time management of nuclear waste. In the heterogeneous concept the radionuclides are incorporating in an inert ceramic matrix. The support material must be insensitive to radiation damage. Fission product damage is the main radiation damage source during the transmutation process and therefore it is of the utmost importance to study their effects. We irradiated spinels MgAl_2O_4 (matrix of reference) and ZnAl_2O_4 by fast ions (by example: (86)Kr of approximately 400 MeV) simulating the fission products. Under these conditions, the damage is primarily due to the electronic energy losses (Se). One of the structural features of spinel AB_2O_4 is that the two cations (A(2+) and B(3+)) can exchange their site. This phenomenon is quantified by the inversion parameter. We highlight by XRD in grazing incidence that the structural changes observed in ...

International Nuclear Information System (INIS)

The development of light-weight vehicle is in great demand for enhancement of fuel efficiency and dynamic performance. The vehicle weight can be reduced effectively by using lightweight materials such as magnesium alloys. However, the use of magnesium alloys in sheet forming processes is still limited because of their low formability at room temperature and the lack of understanding of the forming process of magnesium alloys at elevated temperatures. In this study, uniaxial tensile tests of the magnesium alloy AZ31B-O at various temperatures were performed to evaluate the mechanical properties of this alloy relevant for forming of magnesium sheets. To construct a FLD (forming limit diagram), a forming limit test were conducted at temperature of 100 and 200 deg. C. For the evaluation of the effects of the punch temperature on the formability of a rectangular cup drawing with AZ31B-O, ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium is known to have poor formability at room temperature, mainly attributed to its hexagonal lattice structure. This paper presents the findings generated from development of warm forming to produce thin-walled magnesium components. Finite element analysis was conducted to evaluate the formability of the material and the simulated results were compared to the tensile results and product formability. Tensile tests were used to verify the formability of the sheet metal at difference temperatures. The process parameters considered in the feasibility study were forming temperature, in the range of 28 C to 300 C and magnesium sheet (AZ31B-H24) thickness, in the range of 0.4 mm to 1 mm. Magnesium hand phone covers of a thickness down to 0.4 mm have been successfully produced. The feasible forming temperature was found to be between 200 C and 250 C. Metallographic examination shows evident of ...

Energy Technology Data Exchange (ETDEWEB)

A chromium-free conversion coating for magnesium alloys were described. The conversion coating could be obtained when AZ31D magnesium alloy was immersed in a solution containing a manganese salt, phosphate and an inhibitor. Corrosion resistance of the chemical conversion coating was evaluated by anodizing polarization curve and salt immersion. XRD analysis showed that the conversion coating was mainly composed of Mn{sub 3}(PO{sub 4}){sub 2}. The morphology of the coating is observed by using SEM. The effect of electrolyte pH and concentration of inhibitor on coating growth are investigated. (orig.)

Science.gov (United States)

... alloys--Lanthanum-- Magnesium--Magnasium &11oy8--Hagn*31Uft compounds--Manxganese--Manganes. alloys-- Mercury ...

International Nuclear Information System (INIS)

Magnesium alloys have been increasingly used in automotive and electronic industries because of their excellent strength to weight ratio and EMI shielding properties. However, magnesium alloys have low formability at room temperature due to their unique mechanical behavior (twinning and untwining), prompting for forming at an elevated temperature. In this study, a temperature dependent constitutive model for magnesium alloy (AZ31B) sheet is developed. A hardening law based on non linear kinematic hardening model is used to consider Bauschinger effect properly. Material parameters are determined from a series of uni-axial cyclic experiments (T-C-T or C-T-C) with the temperature ranging 150-250 deg. C. The influence of temperature on the constitutive equation is introduced by the material parameters assumed to be functions of temperature. Fitting process of the assumed model to measured data is presented and the results are ...

International Nuclear Information System (INIS)

One of the major concerns during high speed welding of magnesium alloys is the presence of porosity in the weld metal that can deteriorate mechanical properties. This study seeks to analyze the presence method and quantity of pore during hybrid laser-tungsten inert gas arc (TIG) welding of magnesium alloy AZ31B by radiography, optical microscopy and electron probe microanalysis (EMPA). At the same time, it identifies both the mechanism of pore formation and a remedy for this problem. The experimental results indicate that lacking of shielding gas for laser beam is the dominant cause of macroporosity formation during the hybrid of laser-TIG welding of magnesium Alloys AZ31B plate, and hydrogen is not main cause to form large pores. A favorable weld without porosity can be obtained by appending lateral shielding gas for laser beam.

Energy Technology Data Exchange (ETDEWEB)

In this paper, for an acceleration of utilization of magnesium alloy which is being interested in recent years, friction welding of AZ31 magnesium alloy was carried out, and the joint performance was discussed in relation to the deformation heat input in the upset stage and upset loss as a evaluation factor. Where, the deformation heat input in the upset stage is mechanical work represented by the product of upset speed and axial pressure. As a result, it was made clear that the friction welding of AZ31 magnesium alloy was easy in the atmosphere, and good welded joints without a non- adhesion area at the weld interface could de obtained. Moreover, the evaluation factors discussed were possible to evaluate to joint performance. (orig.)

British Library Electronic Table of Contents (United Kingdom)

A microanalytical characterization of cast magnesium alloys of eutectic origin based on the Mg?Al?Ca ternary matrix system has been carried out in order to investigate the influence of alloying elements on their microstructure as well as microchemistry-processing-microstructural relations using structure-sensitive techniques of electron microscopy, mechanical spectroscopy (internal friction), X-ray diffractometry, and advanced microanalytical methods including electron probe compositional analysis. Following the data obtained here there is direct correlation of microstructure with creep properties of the new experimental magnesium alloys. The creep and heat-induced properties of the multicomponent magnesium alloys containing low range of inexpensive additions of titanium (0.07?0.2%) or str...

Energy Technology Data Exchange (ETDEWEB)

Although magnesium is not attacked by hydrocarbons, it reacts vigorously with anhydrous methanol, raising concerns about the compatibility of the metal with methanol blend fuels. This paper describes the behavior of magnesium alloys in laboratory tests in static contact with methanol-containing fuels at 110/sup 0/F. Water in small concentrations (above 0.25% by weight of the methanol content) is shown to prevent the destructive attack of magnesium by these fuels. The required water content is well within the water tolerance of methanol-GTBA (gasoline grade tertiary-butyl alcohol) cosolvent fuel blends. Die cast AZ91HP shows greater resistance to methanol reaction than does AZ31B sheet.

Energy Technology Data Exchange (ETDEWEB)

A new technique was proposed in order to improve poor corrosion resistance in magnesium. That is, magnesium hydroxide film was formed on the surface of 3 N-Mg by artificial corrosion in 1% MgCl{sub 2} solution for 3.6 ks, which followed by oxidation at 673 K for 3.6 ks in air. Corrosion resistance was evaluated by salt immersion tests in 1% NaCl solution under in situ laser microscopic observations. Bubble evolution, which occurred immediately at the beginning of the immersion test in the case of non-treated specimen, was suppressed by the process. And also, formation of filiform corrosion was suppressed for about 3.6 ks, which occurred at 180 s in the non-treated specimen. (orig.)

British Library Electronic Table of Contents (United Kingdom)

Lithium-ion batteries are now considered to be the technology of choice for future hybrid electric and full electric vehicles to address global warming. LiCoO2 has been the most widely used cathode material in commercial lithium-ion batteries. Since LiCoO2 has economic and environmental issues, intensive research has been directed towards the development of alternative low cost, environmentally friendly cathode materials as possible replacement of LiCoO2. Among them, spinel LiNi0.5Mn1.5O4 material is one of the promising and attractive cathode materials for next generation lithium-ion batteries because of its high voltage (4.7V), acceptable stability, and good cycling performance. Research advances in high voltage spinel LiNi0.5Mn1.5O4 are reviewed in this paper. Developments in synthesis,...

British Library Electronic Table of Contents (United Kingdom)

Ultra-fine ZnAl2O4 spinel hydrogel precursor synthesized from mixed salt solutions of Zn^2^+ and Al^3^+ ions using ammonium hydroxide-hexamethylenetetramine as basic media for co-precipitation was used as bonding material and sintering aid for pure alumina system. The hydrogel powder exhibited some well-defined ZnAl2O4 spinel phases at 800^oC. Alumina compacts were fabricated by incorporating small proportions of the precursor in alumina powder and firing at different temperatures (1350-1500^oC). The degree of densification was studied by measurement of fired shrinkage, apparent porosity, bulk density and cold crushing strength. Phase compositions and microstructural features of sintered samples were evaluated by XRD and SEM respectively. Addition of 0.2% hydrogel powder to alumina exhibit...

Energy Technology Data Exchange (ETDEWEB)

Passive films formed on Alloy 690 in high-temperature alkaline environments were investigated by potentiodynamic polarization, X-ray photoelectron spectroscopy, transmission electron microscopy and Mott-Schottky approach. Passive current density and donor density of the passive films increase with increasing temperature, due to increased diffusion rates of metallic ions and dehydration of hydroxide phases. The passive films show a duplex structure including an inner layer of fine-grained Cr oxide or spinel oxide and an outer layer of Ni-Fe spinel oxide and Ni hydroxide. A growth model of the passive films on Alloy 690 in high-temperature alkaline environments is proposed and discussed.

Energy Technology Data Exchange (ETDEWEB)

Stoichiometric MgAl{sub 2}O{sub 4} spinel specimens irradiated in FFTF-MOTA at temperatures between 385 and 750C to fluences ranging from 2.2 to 24.9 {times} 10{sup 22}n cm{sup {minus}2} (E>0.1 MeV) darken significantly, but do not develop any significant loss in weight or change in dimensions. Similar behavior was observed in both single crystal and fully dense polycrystalline specimens. Measurements of elastic constants by an ultrasonic technique show that no measurable changes occur as a result of the irradiation. These and other results confirm the stability of this material for fusion application as an electrical insulator.

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys and composites are potentially highly attractive materials for lightweight design in the automotive industry - if common forming technologies, i.e., deep drawing and cold extrusion, are applicable to them; so far, this is seldom the case. The authors have tested some candidate Mg alloys and discuss the results of their measurements in detail. The Figure shows a typical workpiece part obtained by a deep-drawing technique. (Abstract Copyright [2003], Wiley Periodicals, Inc.)

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys have replaced resins as a material for the components of electronic products such as cell phone and notebook personal computer mainly, because of their lightness and rigidity. Thin walls, a complicated shape, and high appearance quality are all needed in the external parts. Die-casting and injection molding are the main method of manufacturing magnesium alloy parts. The optimal cast conditions and mold design have been investigated in order that a few defects such as surface cracks and mold cavities in casting parts would be reduced. Instead of cast, plastic forming technologies such as warm drawing and hot forging have been developed to form thinner walls and less defects. Plastic formability of magnesium alloy in hot working is dependent on a grain size of material. The material with fine grains has advantage of being formed at high strain rate. The characteristics of forming processes of ...

Energy Technology Data Exchange (ETDEWEB)

Machines and structures, such as automobiles are usually subjected to biaxial or three-axial stresses instead of uniaxial stress. However, research on a fatigue failure under multi-axial stress has not been fully presented because such experiments are difficult. To solve this problem, we developed the servo biaxial fatigue-testing machine. In this research, we performed the biaxial fatigue tests of a magnesium alloy in order to clarify the effects from different heat treatments. Magnesium alloy is the lightest in weight among metal materials for structural use. The fatigue characteristics of a magnesium alloy are indispensable in order to create the design which ensures the reliability and the safety of the vehicles especially in long-distance run. The main conclusions are summarized as follows; (1) The mechanical property of magnesium alloy AZ31B falls by heat treatment at low temperature. (2) The ...

International Nuclear Information System (INIS)

Lithium-ion batteries are now considered to be the technology of choice for future hybrid electric and full electric vehicles to address global warming. LiCoO2 has been the most widely used cathode material in commercial lithium-ion batteries. Since LiCoO2 has economic and environmental issues, intensive research has been directed towards the development of alternative low cost, environmentally friendly cathode materials as possible replacement of LiCoO2. Among them, spinel LiNi0.5Mn1.5O4 material is one of the promising and attractive cathode materials for next generation lithium-ion batteries because of its high voltage (4.7 V), acceptable stability, and good cycling performance. Research advances in high voltage spinel LiNi0.5Mn1.5O4 are reviewed in this paper. Developments in synthesis, structural characterization, effect of doping, and effect of coating are presented. In addition to conventional synthesis methods, several alternative ...

Science.gov (United States)

{sup 1}H, {sup 13}C, {sup 27}Al, and {sup 29}Si magic-angle-spinning (MAS) NMR was used to elucidate the nature of the catalytic activity of zeolite H-ZSM-5. {sup 1}H MAS NMR of sealed samples after mild hydrothermal dealumination shows that the enhanced activity for n-hexane cracking is not due to an enhanced Bronstead acidity. The concentrations of the various OH groups and aluminous species suggest that the reason for the enhanced catalytic activity is the interaction of the n-hexane molecule with a bridging hydroxyl group and with extra-framework aluminium species, which give rise to the enhanced activity, cannot be easily removed from their positions, and are therefore immobilized by the zeolitic framework.

International Nuclear Information System (INIS)

A passive dosemeter, based on a Makrofol ED track detector covered with aluminized Mylar, enclosed in diffusion chamber, has been used for radon concentration studies. Detectors have been irradiated, using a "2"4"1Am source, at different energies and fluences in order to obtain the electrochemical etching conditions that allow the optimum registration of alpha particles having energies over 3 MeV. Thirty dosemeters have been sent to the UK National Radiation Protection Board (NRPB) Radon Environmental Chamber for calibration. The sensitivity of the dosemeter has been calculated. Several dosemeters have also been exposed in houses and dwellings in the Barcelona and Madrid areas for monitoring. Values for radon concentration in the areas under study are presented. (author).

Energy Technology Data Exchange (ETDEWEB)

Magnesium alloys are ideal candidates to benefit from equal channel angular extrusion (ECAE) because of their poor forming characteristics due to a hcp structure. In this study, ECAE processing was applied to ZK31 and AZ31 magnesium alloys under various conditions. The grain size of as-ECAE specimens decreases with decreasing the processing temperature, however, the grain size decreases slightly with increasing number of repetitive processing. Both the tensile strength and 0.2% proof stress of as-ECAE specimens are high when processed at low temperature, but the elongation is high when processed at high temperature. Crystal orientation is different in the two alloys and it also varies according to the processing temperature for the two alloys. The difference of the crystal orientation influences the tensile properties, especially 0.2% proof stress. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Applications of magnesium alloys are motivated mainly by their lightweight. However, manufacturing cost should also be evaluated when considering applying them. From this point of consideration, adoption of sheet forming processes, which previously have not been heavily researched, should be an option. This paper is intended to pioneer the study of the formability of magnesium alloy AZ31 out of rolled sheets at elevated temperatures. The rolled microstructures are examined and correlated with their formability. Post-forming conditions will also be investigated. The tool employed to perform the sheet forming experiments was a punchless die-setting which used pressurized gas to press the sheet into a female die cavity. This technique applied to Mg-alloy is unconventional and warrants attention for its potential utilization in the industry. (orig.)

Energy Technology Data Exchange (ETDEWEB)

We conduct the static and dynamic loading fracture experiments on magnesium alloy (AZ31B) under the equitable and inequitable biaxial stress. We process specimens as cross type with cracks. There are different kinds of cracks defined by their crack angles. By using a hydraulic high-speed biaxial experiment machine, we put the equitable and inequitable stresses on the specimen. We analyze results using the caustic method. The experiments reveal a few important results. There is negative correlation between the fracture toughness value and the plate thickness in the magnesium alloy sheet specimen. The fracture toughness value decrease in the case the crack has the angle different from the loading direction. The fracture toughness value decreases significantly under the inequitable biaxial stress. (orig.)

International Nuclear Information System (INIS)

Lithium Ceramics offer tremendous potential as a source for the production of tritium ("3H) for fusion power reactors. Their successful application will depend to a great extent upon the diffusion properties of the "6Li within the matrix. Consequently knowledge of "6Li concentration gradients in the ceramic matrices is an important requirement in the continued development of the technology. In this investigation, the neutron depth profile (NDP) technique has been applied to the study of concentration profiles of "6Li in lithium aluminate ceramics, doped with 1.8%, 50% and 95% "6Li isotopic concentrations. Specimen for analysis were prepared at Battelle (PNL) as pellet discs. Samples for diffusion studies were arranged as diffusion couples in the following manner: 1.8% "6Li discs/85% "6Li powder. Experiments were performed at the Texas A and M Nuclear Science Center Reactor Building, utilizing 1 MW equivalent thermal neutron fluxes 3x10"1"1 n/m"2 s. The depth probed ...

International Nuclear Information System (INIS)

Hybrid organic-inorganic coatings with phosphonate functionalities have been synthesized and evaluated as prospective surface treatments for magnesium materials. These coatings have been processed via a sol-gel route by hydrolysis and condensation of a mixture of diethylphosphonatoethyltriethoxy-silane and tetraethoxy-silane with variable molar ratios. The coatings morphology and the surface chemistry at the coating/substrate interface have been characterized using scanning electron microscopy, X-ray photoelectron spectroscopy, "3"1P nuclear magnetic resonance spectroscopy, and time-of-flight secondary ion mass spectrometry. The corrosion protection performance of the coatings deposited on magnesium alloy AZ31B has been examined by a group of electrochemical techniques including potentiodynamic polarization and electrochemical impedance spectroscopy. In addition, a scanning Kelvin probe technique has been used to investigate interfacial ...

Science.gov (United States)

... having high fluidity. The SC-51A alloy contains 4.5 to 5.5% silicon, 1 to 1.5% coppers .4 to .6% magnesium, o35% sine, .8% iron, .5% manganes*, ...

Science.gov (United States)

The effects of various fixative agents, pH, ionic strength, stain concentration, and magnesium concentration on DNA staining with the antibiotics olivomycin, chromomycin A3, and mithramycin were examined with DNA in solution and in mammalian cells.

Science.gov (United States)

The biocompatibility and corrosion resistance of various materials for use as sacrificial anodes in in vivo hybrid fuel cells were studied. Aluminium, zinc, and magnesium alloy AZ31B were studied, and the results are discussed.

Energy Technology Data Exchange (ETDEWEB)

Effect of strain rate, temperature and grain size in the climb-controlled dislocation creep region for AZ31 magnesium alloy was examined at lower temperature of {proportional_to}473 K. The flow stress was not affected by the difference in grain size. The strain rate sensitivity, m, was obtained 0.14 and 0.2 at low temperatures in high strain rate and at high temperature in low strain rate, respectively. It was found that the notion of effective diffusivity could express the dominant diffusion process during climb-controlled dislocation creep behavior uniquely. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The microstructures of magnesium AZ31 are examined following hot compression testing and annealing. The grain size, fraction dynamically recrystallized and, in a couple of cases, the crystallographic texture are reported. It was found that the progress of dynamic recrystallization is strongly sensitive to processing conditions but that the dynamically recrystallized grain size was less sensitive to stress than in other metals. It was also found that, for structures containing between 80 and 95% dynamic recrystallization, abnormal grain growth occurs during annealing. The crystallographic texture produced is also sensitive to the deformation conditions. (orig.)

Energy Technology Data Exchange (ETDEWEB)

To investigate the influence of equal channel angular pressing on the microstructure and texture of the magnesium alloy AZ31, electron backscattering diffraction and well as neutron diffraction experiments were carried out. Through these experiments it was possible to trace the microstructure and texture evolution with strain accumulated with the increasing number of equal channel angular pressing passes. It was further demonstrated by subsequent compression tests that the microstructural changes produced by equal channel angular pressing have a beneficial effect on both the compressive strength and ductility of AZ31. (orig.)

International Nuclear Information System (INIS)

The effect of a mineralizer, magnesium silicate, on the nitridation of compacts consisting of silicon, clay, silica and silicon carbide was examined in terms of their reaction depth, density, porosity, phase composition and microstructure. It was found that addition of mineralizer slowed down the nitridation significantly. The kinetic process of isothermal nitridation in the presence of magnesium silicate obeys a parabolic rate law. Otherwise it obeys a linear rate law. The results suggest that nitrogen transportation is the limiting step during nitridation when mineralizer is added. The mechanism of nitridation is discussed in terms of phase composition and microstructure. Copyright (2000) The Australian Ceramic Society

Energy Technology Data Exchange (ETDEWEB)

Superparamagnetic MFe{sub 2}{sup 3+}O{sub 4} (M=Mn{sup 2+}, Fe{sup 2+} and Co{sup 2+}) inverse spinel ferrite (ISF) nanoparticles with narrow size distribution having average diameters of 6-8 nm were synthesized by a diol reduction of organic metals and the surface was modified to be hydrophilic by coating with succimer. Magnetic resonance imaging (MRI) contrast enhancement by dipolar coupling defined interactions between the synthesized ISFs and protons in the bulk water was investigated with initial susceptibility, magnetization and anisotropy of the succimer-coated ISFs. The relaxivity ratios, r{sub 2}/r{sub 1}, for MnFe{sub 2}O{sub 4}, Fe{sub 3}O{sub 4} and CoFe{sub 2}O{sub 4} were measured to be 12.2, 23.1 and 62.3, respectively, which demonstrate the potential usefulness of these magnetic nanoparticles as T{sub 2} contrast agents for MRI.

International Nuclear Information System (INIS)

Superparamagnetic MFe23+O4 (M=Mn2+, Fe2+ and Co2+) inverse spinel ferrite (ISF) nanoparticles with narrow size distribution having average diameters of 6-8 nm were synthesized by a diol reduction of organic metals and the surface was modified to be hydrophilic by coating with succimer. Magnetic resonance imaging (MRI) contrast enhancement by dipolar coupling defined interactions between the synthesized ISFs and protons in the bulk water was investigated with initial susceptibility, magnetization and anisotropy of the succimer-coated ISFs. The relaxivity ratios, r2/r1, for MnFe2O4, Fe3O4 and CoFe2O4 were measured to be 12.2, 23.1 and 62.3, respectively, which demonstrate the potential usefulness of these magnetic nanoparticles as T2 contrast agents for MRI.

Energy Technology Data Exchange (ETDEWEB)

Mn{sub 1-x}Fe{sub x}In{sub 2}S{sub 4} spinel compounds (x=0.3, 0.8) were grown by the chemical vapor transport method. The analysis of the X-ray diffraction data suggest that both the compounds crystallize in a cubic structure under the space group Fd3m. The magnetic study done between 300 and 2 K showed a paramagnetic behavior for the intermediate concentration sample x=0.3. A good fitting to the Curie-Weiss law allows us to calculate the paramagnetic Curie temperature. They are negative indicating predominant antiferromagnetic interactions. However, in sample with high Fe concentration, x=0.8, it was possible to observe a peak at around T{sub sg} congruent with 10 K. From ac magnetic susceptibility data at different driving frequencies f, it is found that the peak at T{sub sg} shifts to lower temperatures with decreasing frequency suggesting an spin-glass behavior.

Energy Technology Data Exchange (ETDEWEB)

The influence of Cr on the structure and electrochemical properties of LiCoVO{sub 4} was studied using X-Ray diffraction, scanning electron microscopy, Raman Spectroscopy and cycle tests. Doping levels up to 10 mol% were achieved, which improved the electrochemical stability of the structure of LiCoVO{sub 4}, resulting in a significant increase in the initial charge and discharge capacity. The Raman spectroscopy data for the Cr-doped LiCoVO{sub 4} is similar as for LiCoVO{sub 4}. The replacement of a dopant for the Co-ion in the inverse spinel structure causes several Raman shifts. The X-ray diffraction patterns show no new phases and combined with the Raman spectroscopy data it is concluded that the Cr dopant will be located at the octahedral site (16d) where they create an electronic pathway that enhances the electronic conductivity. However, the capacity dropped significantly after prolonged cycling, which is due to the diffusion of V{sup 5+} ions from the ...

British Library Electronic Table of Contents (United Kingdom)

A series of spinel Li4Ti5O12 samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li4Ti5O12. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li4Ti5O12 with L=1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized...

International Nuclear Information System (INIS)

Non-anisotropic free energy is considered which under minimization yields two magnetic phases: a conical spin density wave and a low temperature conical cycloid. Using equations of motion, the excitation spectrum is studied. Knowing the nature of these excitations, the dielectric function as well as the fluctuation specific heat is computed and compared with the experimental spectrum. Due to the electromagnon going soft, the dielectric function (imaginary part) as well as the specific heat capacity show peaks at the temperature where ferroelectricity appears in the system.

Energy Technology Data Exchange (ETDEWEB)

Our objective is to increase both the life and power of the molten carbonate fuel (MCFC) by developing improved components and designs. Current activities are as follows: (1)Development of LiFeO{sub 2} and LiCoO{sub 2} cathodes for extended MCFC life, particularly in pressurized operation, where the present cathode, NiO, provides insufficient life (2) Development of distributed-manifold MCFC designs for increased volumetric power density and decreased temperature gradients (and, therefore, increased life) (3) Development of components and designs appropriate for high-power density operation (>2 kW/m{sup 2}and >100 kW/m{sup 3}in an integrated MCFC system) (4)Studies of pitting corrosion of the stainless-steel interconnects and aluminized seals now being employed in the MCFC (alternative components will also be studied). Each of these activities has the potential to reduce the MCFC system cost significantly. Progress in each activity will be presented during ...

Energy Technology Data Exchange (ETDEWEB)

The pozzolanic behaviour of compound-activated red mud-coal gangue has been investigated through TG, DTA, XRD, FTIR and {sup 27}Al MAS NMR. From viewpoint of reaction kinetics, it is found that the pozzolanic reaction mechanism of the compound-activated red mud-coal gangue-lime system is clearly consistent with diffusion control up to 14 days, and the reaction rate constant calculated from Jander equation decreases with the increase of CaO addition in the system. The hydration products formed in the red mud coal gangue-lime systems at ambient temperature are essentially aluminous C-S-H and Ca{sub 3}Al{sub 2}O{sub 6} center dot xH{sub 2}O. From TG analysis results, it is thought that the high amount of Ca(OH){sub 2} in the pastes of studied system is not conducive to the continual increase of non-evaporable water content of the hydration products. Of particular interest. {sup 27}Al MAS NMR proved to be an effective technique to obtain valuable information of Al(4) ...

International Nuclear Information System (INIS)

We describe a panoramic stigmatic spectrograph comprising a grazing-incidence toroidal mirror and a large-aperture free-standing transmission diffraction grating (5000 lines mm-1 ). Two spectrograph versions were constructed, with grazing angles of 7.6 and 40 and the short-wavelength spectral limits near 4 and 1.5 nm. The spectrograph aberrations were studied by numerical ray tracing. The spectrograph was used to record line and quasi-continuous spectra (1.5 - 30 nm) of multiply charged ions in a plasma generated by the second-harmonic pulses of an yttrium aluminate laser (Q = 0.15 J, ? = 5 ns, ? = 0.54 ?m, repetition rate = 0.5 Hz). In combination with a laser-produced plasma radiation source, the arrangement was used to characterise soft x-ray optical components and to generate collimated beams of polarised radiation in the 14 - 20 nm range. (laser applications and other topics in quantum electronics)

Energy Technology Data Exchange (ETDEWEB)

Better properties of magnesium make it a natural choice for use as an anode material in rechargeable batteries. However, the magnesium alloy thin sheets used in rechargeable batteries were produced by ingot casting and rolling. That technology was so complex and the cost was high. Rapidly solidification by melt spinning is an effect way to solve that problem. In this paper, the technology of rapidly solidified (RS) ribbons in Mg-3%Al-1%Zn-0.2%Mn alloy has been investigated using melt spinning technique. The effect of wheel speed on thickness and microhardness of the ribbons is presented. Microhardness is found to increase with the wheel speed. Rapidly solidification leads to small grains (1{proportional_to}2 {mu}m). The plasticity of the ribbons was well. The quantity of Mg{sub 17}Al{sub 12} decreases with the increase in wheel speed. When the wheel speed reaches 1600 rpm, no Mg{sub 17}Al{sub 12} phase precipitates. As the increase of the wheel ...

Energy Technology Data Exchange (ETDEWEB)

Feasibility of mushy state forming of magnesium alloys making use of resistance heating was examined. Magnesium alloys, AZ31, AZ61 and AZ91, were taken up as experimental materials and cylindrical billets with a diameter of 15 mm and a height of 20 mm were used for both resistance heating and forming experiments. Input heat control was applied to the billet heating and insertion of thin discs of austenitic stainless steel with a low thermal conductivity between the billet and copper electrodes was attempted in order to improve the efficiency of the billet heating. Results were summarized as follows. (1) Resistance heating by input heat control was successful to heat the billets to their respective mushy state. (2) Insertion of the discs was very helpful in heating the billets and realized the heating in a couple of seconds. (3) The force applied to the electrodes to ensure the electrical contacts being too small, sparks occurred and welds arose ...

Energy Technology Data Exchange (ETDEWEB)

The experiment was carried out on a short rotation coppice culture of poplars (POP-EUROFACE, Central Italy), growing in a free air carbon dioxide enriched atmosphere (FACE). The specific objective of this work was to study whether elevated CO{sub 2} and fertilization (two CO{sub 2} treatments, elevated CO{sub 2} and control, two N fertilization treatments, fertilized and unfertilized), as well as the interaction between treatments caused an unbalanced nutritional status of leaves in three poplar species (P. x euramericana, P. nigra and P. alba). Finally, we discuss the ecological implications of a possible change in foliar nutrients concentration. CO{sub 2} enrichment reduced foliar nitrogen and increased the concentration of magnesium; whereas nitrogen fertilization had opposite effects on leaf nitrogen and magnesium concentrations. Moreover, the interaction between elevated CO{sub 2} and N fertilization amplified some element unbalances such ...

Energy Technology Data Exchange (ETDEWEB)

There are many factors affecting diffusion bonding in order to obtain high quality joining. Therefore, in the beginning, we constructed diffusion bonding model based on void growth mechanism to predict bonding pressures and times. In addition, in order to compare theoretical values with experimental values, diffusion bonding tests were carried out by using commercial AZ31 magnesium alloy sheets with different grain sizes, 16 and 130 {mu}m. The present AZ31 alloys were successfully diffusion bonded at several conditions, and the bonding strength was more than 0.8 of each parent materials. The experimental bonding conditions in high quality joining, times and pressures, were good agreed with prediction analysis. (orig.)

Energy Technology Data Exchange (ETDEWEB)

This research investigated the inhibiting effects that sodium salts of linear monocarboxylic acids displayed towards the corrosion process of AZ31 Mg alloy in ASTM D 1387 saline solution (a synthetic industrial cooling water). The length of the aliphatic chain of the acids ranged between 7 and 15 carbon atoms. The inhibiting action of these salts can be related to the precipitation of an insoluble magnesium salt, which mainly affected the anodic reaction. The aliphatic chain length controlled the anion solubility and the reaction rate of magnesium carboxylate formation. For all the salts, an optimum concentration was experienced: 10{sup -2} M for sodium decanoate (caprate), 10{sup -3} M for sodium dodecanoate (laurate), 10{sup -4} M for sodium tetradecanoate (myristate); when this concentration was exceeded, a diminution (even a disappearance) in the inhibiting action was found. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

International Nuclear Information System (INIS)

Consideration is given to the data, demonstrating the effect of ion radiation on strength characteristics of ionic crystals, presented by magnesium oxide. Crystals, prepared in the form of plates, were irradiated by Si"+, Fe"+, C"+ ions by the dose of 10"1"6-10"1"7 ion/cm"2 at room temperature in vacuum. The following characteristics were investigated: dislocation density, microhardness, crack resistance. Investigation of dislocation structure showed, that dislocation density in irradiated sample was 2-3 times higher, as compared to nonirradiated one. Sufficient increase of fracture viscosity of MgO crystals was revealed. It can be conditioned by occurrence of compression stresses in the surface layer, decelerating crack formation and propagation.

Energy Technology Data Exchange (ETDEWEB)

Dynamic development of new grain boundaries was studied in compression of a magnesium alloy AZ31 with initial grain sizes (D{sub 0}) of 22 {mu}m and 90 {mu}m at a temperature of 673 K. Kink bands are evolved near corrugated grain boundaries and in grain interiors at low strains accompanied with new fine grains. Kink bands are developed often perpendicular to the basal plane. The boundary misorientation of kink band as well as the volume fraction of new grains increases rapidly with increasing strain and approaches a saturation value in high strain. New fine grains are developed faster with decrease in the D{sub 0}. It is concluded that new grain evolution is controlled by a deformation-induced continuous reaction, i.e. continuous dynamic recrystallization (DRX). (orig.)

International Nuclear Information System (INIS)

A method is described for determination of aluminium, cadmium, cobalt, chromium, copper, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, zinc, titanium and vanadium in iron ore. After dissolution, a 1 gram sample of iron ore is applied to a column of AGI-X8 anion exchange resin (chloride form), in 100 ml of 7M HCl. Aluminium, chromium, calcium, magnesium, sodium, potassium, manganese, nickel, lead, strontium, titanium and vanadium are eluted with 7M HCl; iron, copper and cobalt are eluted with 0.5M HCl; cadmium and zinc are eluted with 2M HNO_3. Iron is subsequently removed from copper and cobalt by a solvent extraction with methyl isobutyl ketone. The elements are determined in the eluates by atomic absorption spectrometry, except for titanium and vanadium, which are determined spectrophotometrically.

International Nuclear Information System (INIS)

Moss-Schottky plots and photoelectrochemical measurements were made on films formed at different potentials on AISI 304 stainless steel in a borate/boric acid solution, pH 9.2. The results allowed the determination of the semiconductive properties and band structure of the films, which account for the existence of two kinds of films depending on the formation potential. For potentials below 0 V (SCE), the results point out for a film with an inverse spinel structure constituted by Cr-substituted magnetite with two donor levels. Above 0 V only one donor level is detected, which should be Fe"2 "+ on tetrahedral sites.

International Nuclear Information System (INIS)

The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry.

International Nuclear Information System (INIS)

The physical, chemical and mechanical properties of magnesium alloys make them attractive materials for automotive and aerospace applications. However, these materials are susceptible to corrosion and wear. This work discusses the potential of using sol-gel based coatings consisting of ZrO_2 and 15 wt.% of CeO_2. The CeO_2 component provides enhanced corrosion protection, while ZrO_2 impart corrosion as well as wear resistance. Coating deposition was performed by the dip coating technique on two magnesium alloy substrates with different surface finishes: AZ91D (as-casted, sand-blasted, and machined) and AZ31 (rolled and machined). All as-deposited coatings (xerogel coatings) were then subjected to 10 h annealing: a temperature of 180 C was applied to the AZ91D alloy and 140 C to the AZ31 alloy. Morphological and structural properties of the annealed coatings were investigated by scanning electron microscopy, atomic force microscopy and ...

Science.gov (United States)

A number of alloys of zirconium have been investigated as part of a program aimed at improving the high-temperature tensile and creep strength of zirconium. These alloys include aluminum, beryllium, lead, magnesium, molybdenum, niobium, tantalum, tin, titanium, tungsten, vanadium, and zinc, binary and ternary alloys. The data indicate that aluminum, lead, molybdenum niobium, tin, titanium, tungsten, and vanadium can be used successfully to harden zirconium, and that aluminum, tin, titanium, and vanadium are particularly effective in maintaining the strength of zirconium at elevated temperatures.

Energy Technology Data Exchange (ETDEWEB)

Nutrient elements contained in litter fall flux, that of uptake flux and turnover rate had generally tended to increase with the increase in the Warmth Index, while the amount of nutrient in the A[sub 0] horizon and nutrient use efficiency did not. However, it is suggested that topographic and climatic aridity, and the amount of available and exchangeable phosphorus, calcium and magnesium greatly affect the nutrient dynamics in a each forest ecosystem as the Warmth Index increases. (J.P.N.).

International Nuclear Information System (INIS)

Dynamic recrystallization (DRX) is the main softening mechanism of magnesium alloy AZ31B in hot deformation. Theoretically, in the flow rule the atomic diffusibility and the driving force of dislocation migration are dependent on the temperature, and the dislocation density and the cumulation of grain boundary energy are dependent on the strain rate. The peak stress will appear when the flow driving force and resistance force reach a balance, after which the stress descending will take place due to recrystallization fraction. Since the DRX is a thermally activated process, the recrystallized volume fraction can be regarded as the function of strain through Avrami equation. Based on this idea, the paper proposes a new constitutive model characterizing dynamic recrystallization for magnesium alloy AZ31B. The model is described by a peak stress and a strain softening rate, in which the peak stress depends only on Zener-Hollomon parameter and is ...

Energy Technology Data Exchange (ETDEWEB)

A series of spinel Li{sub 4}Ti{sub 5}O{sub 12} samples were synthesized via a composite molten-salt method (CMSM) using the mixtures of LiCl and KCl with different L values (L is defined as the molar ratio of LiCl:KCl) as the reaction media. It is found that the melting point of the composite molten salt can effectively influence the formation of particles, and leads to different electrochemical performances of the as-prepare Li{sub 4}Ti{sub 5}O{sub 12}. The investigations of X-ray diffraction (XRD), particle size distribution (PSD), Brunauer-Emmet-Teller (BET) surface area, and scanning electron microscopy (SEM) indicate that the as-prepared Li{sub 4}Ti{sub 5}O{sub 12} with L = 1.5 is a pure phase, and has uniform homogeneous octahedral shape particles, rather narrow PSD, and high BET surface area. Electrochemical tests show that the optimized Li{sub 4}Ti{sub 5}O{sub 12} with L = 1.5 has an initial discharge capacity of 169 mAh g{sup -1} and an initial ...

Energy Technology Data Exchange (ETDEWEB)

Aluminum is a principal element in alkaline nuclear sludge waste stored in high level waste (HLW) tanks at the Savannah River Site. The mass of sludge in a HLW tank can be reduced through the caustic leaching of aluminum, i.e. converting aluminum oxides (gibbsite) and oxide-hydroxides (boehmite) into soluble hydroxides through reaction with a hot caustic solution. The temperature limits outlined by the chemistry control program for HLW tanks to prevent caustic stress corrosion cracking (CSCC) in concentrated hydroxide solutions will potentially be exceeded during the sludge mass reduction (SMR) campaign. Corrosion testing was performed to determine the potential for CSCC under expected conditions. The experimental test program, developed based upon previous test results and expected conditions during the current SMR campaign, consisted of electrochemical and mechanical testing to determine the susceptibility of ASTM A516 carbon steel to CSCC in the relevant environment. Anodic ...

International Nuclear Information System (INIS)

Single pellets (of approximately 70 g each) of irradiated lithium aluminate target from N-Reactor test PT-57 were used in a series of experiments to determine the extent to which the product tritium can be recovered by (a) vacuum outgassing of the target (thermal extraction-TX) and (b) in-vacuo chemical dissolution of the target in molten sodium tetraborate (flux extraction-FX). Five TX runs and seven FX runs were made. Thirty-five percent of the tritium was recovered in a form non-condensable at -196"0C. The remainder was recovered in a condensable form (as T_2O, HTO, etc.). Post-extraction analysis of the melt from the seven flux extractions showed that a maximum of 2 percent of the original amount of tritium remained and that target dissolution was essentially complete in 12 hours. Flux extraction of two pellets which had been subjected to thermal extraction showed less than 0.4 percent of the original amount of tritium remaining. Within experimental accuracy ...

Energy Technology Data Exchange (ETDEWEB)

Stearic acid gel is employed to study the phase evolution of MgTiO{sub 3} nanoparticles by thermal gravimetric analysis, X-ray diffraction, and Fourier transform infrared. During the preparation of stearic acid gel, tetrabutyl titanate easily absorbed moisture to hydrolyze into Ti(OH){sub 4} firstly, and then reacts with stearic acid and magnesium stearate to form magnesium-titanium oxide network polymer gel, meanwhile n-butanol is generated. When stearic acid gel is calcined in air, a series of oxidation and combustion reactions occur, meanwhile apparent heat is given off. The results show that a metastable intermediate phase Mg{sub 2}TiO{sub 4} is generated at 450 {sup o}C and nearly disappeared at 550 {sup o}C. Simultaneously, a new solid phase of MgTiO{sub 3} appears. The metastable intermediate phase Mg{sub 2}TiO{sub 4} is successfully identified in the current work.

Energy Technology Data Exchange (ETDEWEB)

In this study, isothermal torsion tests were carried out on magnesium AZ31B alloy under constant strain rate conditions, in the range of 250 to 400 C at 0.01, 0.1, and 1.0 s{sup -1}. Alloy flow stress dependence on strain rate and temperature can be described by a power law with activation energy of 130 kJ/mol. Microstructural examination of hot deformed samples shows very fine recrystallized grains decorating grain boundaries of larger gains in the form of a necklace. These fine grains are produced by dynamic recrystallization at the grain boundaries of original grains. Microstructure evolution, based on samples quenched at different strain levels, indicates that increasing deformation strain has little effect on recrystallized grain size but widens the recrystallized region, with full recrystallization achieved at a certain high strain level. Recrystallized grain size increases with increasing deformation temperature and strain rate. The latter suggests ...

Energy Technology Data Exchange (ETDEWEB)

The tensile and compressive properties as well as LCF and HCF performance of the extruded magnesium alloys AZ31 and AZ80 were determined in extrusion (L) and long-transverse (T) directions. Owing to marked crystallographic textures, both alloys showed pronounced directional mechanical properties in monotonic as well as cyclic loading with strength values in L-direction being significantly superior to those in T-direction. Thermomechanical treatments such as pressing, swaging and rolling were found to increase yield stresses and HCF strengths and to alter the directionality in properties due to textural modifications. To further improve HCF strengths, mechanical surface treatments such as shot peening, roller-burnishing and deep rolling were utilized. The results indicate marked improvements provided that suitable process parameters are used. The improvement of the HCF strengths is explained by the process-induced changes in near-surface dislocation densities and ...

Energy Technology Data Exchange (ETDEWEB)

Three kinds of thin AZ31 wrought magnesium alloys sheets were used in order to investigate the influence of the second phase particles on fracture toughness. From the theoretical model, the ratio of {lambda}{sub p}/d{sub p} would be estimated 5 {proportional_to} 6. On the other hand, from the microstructural observation, average particle spacing on each material was sample A: 13.1 {mu}m, sample B: 14.1, and sample C: 12 {mu}. In addition, average particle size on each sample was sample A: 2.1, sample B: 1.9, and sample C: 2.3 {mu}m. Therefore, the ratio of {lambda}{sub p}/d{sub p} calculated from fracture surface observation would be predicted 6 {proportional_to} 7. In comparison with the result of the prediction by theoretical analysis was in good agreement with the result of fracture toughness observation. It was found that the variation in plane-strain fracture toughness on AZ31 were affected by both of particle spacing and particle size. (orig.)

Energy Technology Data Exchange (ETDEWEB)

The deformation behavior and structure changes of magnesium alloy AZ31 were studied in compression at temperatures ranging from 523 K to 673 K and at a strain rate of 3 x 10{sup -3} s{sup -1}. They depend sensitively on deformation temperature. At high temperatures, grain fragmentation takes place due to frequent formation of kink bands initially at corrugated grain boundaries and then in grain interiors, followed by full development of new grains in high strain. At lower temperatures, in contrast, twinning takes place in rather coarse grains and kink bands are formed mainly in finer original ones in low strain. It is concluded that new grain evolution can be controlled by a deformation-induced continuous reaction resulting in grain fragmentation by kink bands, i.e. continuous dynamic recrystallization (cDRX). The latter is discussed comparing with conventional, i.e. discontinuous, DRX. (orig.)

British Library Electronic Table of Contents (United Kingdom)

The effect of ammonia treatment in field natural rubber (NR) latex with different storage period time on the properties of concentrated NR latex and stability of skim latex was investigated. Fresh NR latex was treated with various ammonia contents such as 0.35, 0.60 and 0.80% w/w, and then they were centrifuged to get the concentrated NR latex with 60% dry rubber content (DRC) containing 0.16, 0.18 and 0.25% w/w, respectively and skim NR latex with roughly 5% DRC containing 0.42, 0.60 and 0.80% w/w, respectively. The effect of storage times with ?0, 15, 30 and 45 days for concentrated NR latex with different ammonia contents on their properties such as alkalinity, magnesium content and viscosity was observed. It was found that generally, magnesium content in field NR latex and latex...

Energy Technology Data Exchange (ETDEWEB)

The mechanical behaviour of wrought magnesium alloy AZ31 has been characterised by tensile testing at room temperature. Tests were carried out at various strain rates between 0.00003 s{sup -1} and 0.01 s{sup -1} on material which had been extruded to a bar of approximately 6 mm thick, and 80 mm wide. Specimens were machined from three orientations relative to the extrusion direction: parallel, perpendicular, and 45 from the extrusion direction. Significant variations of the properties were observed depending on the extrusion orientation and strain rate. At all strain rates the yield stress declined as the test orientation was rotated away from the extrusion direction. Parallel to the extrusion direction, the yield stress was found to increases markedly with increasing strain rate, whereas at 45 and 90 a lesser influence of strain rate was observed. The work hardening exponent was also influenced by the test orientation. Metallographic studies revealed a ...

International Nuclear Information System (INIS)

Multi-cation #alpha#-Sialon ceramics were prepared using mixtures of samarium with calcium, magnesium, yttrium and ytterbium, and compared with a pure Sm-Sialon of equivalent total stabilising cation composition. A ratio of 80eq% samarium to 20eq% of the second stabilising additive was used. Samples were fired at 1820 deg C and subsequently heat treated at 1450 deg C. XRD phase analysis showed that all additives resulted in greater #alpha#-Sialon stability, and that calcium was the most effective additive for the stabilisation of the #alpha#-Sialon phase. Copyright (1998) Australasian Ceramic Society

International Nuclear Information System (INIS)

The description is presented of binary phase diagrams of titanium alloyed with the following elements: silver, aluminium, arsenic, gold, boron, barium, beryllium, bismuth, carbon, calcium, cadmium, cobalt, chromium, copper, iron, gallium, germanium, hydrogen, hafnium, indium, iridium, potassium, lithium, magnesium, manganese, molybdenum, nitrogen, sodium, niobium, nickel, oxygen, osmium, phosphorus, lead, palladium, platinum, plutonium, rhenium, lanthanium, cerium, preseodymium, neodymium, gadolinium, erbium, terbium, thulium, lutetium, rhodium, ruthenium, scandium, silicon, tin, strontium, tantalum, technetium, thorium, uranium, vanadium, tungsten, yttrium, ytterbium, zinc and zirconium.

Energy Technology Data Exchange (ETDEWEB)

This specification establishes requirements for design, testing, and quality assurance for electric heaters that will be used to maintain primary Sodium temperature in the Fast Test Facility (FFTF) reactor vessel. The Test Specification (WHC-SD-FF-SDS-003) has been revised to Rev. 1. This change modifies the fabrication of approximately 25 feet of the subject heater using ceramic insulators over the heater lead wire rather than compressed magnesium oxide. Also, 304 or 316 stainless steel can be used for the heater sheath. This change should simplify fabrication and improve the heater operational reliability.

Energy Technology Data Exchange (ETDEWEB)

The theoretical principles underlying the formation of oxide and, in particular, anodic oxide coatings on metals produced by chemical oxidation, anodizing in solutions, and anodizing in cold plasmas are reviewed. The mechanisms and conditions of anodic oxidation are described, and the structure of anodic oxide coatings on aluminum, magnesium, beryllium, zinc, cadmium, iron, cobalt, nickel, titanium, zirconium, tantalum, and chromium alloys is examined. Attention is also given to various applictins of anodized coatings. 54 references.

International Nuclear Information System (INIS)

The adsorption properties of four samples of the #alpha#-modification of boron nitride (#alpha#-BN) were investigated by the gas-chromatographic method. According to the electron microscopy data, the #alpha#-BN particles possess the shape of thin plates. An #alpha#-BN sample prepared from magnesium polyboride, is the most uniform adsorbent. For a series of n-alkanes, benzene, and alkyl benzenes, by testing the #alpha#-BN samples one has obtained the retained volumes (Henry constants) and the values of the differential adsorption heat, which are close to those of the surface zero filling. These thermodynamic characteristics of adsorption have shown that the #alpha#-BN, line the graphitized thermal carbon black, is not a specific adsorbent.

Science.gov (United States)

INTRODUCTION. We searched for a pathophysiologically based feature of major water electrolytes, which may define water quality better than the water hardness, respecting urinary calculus formation. MATERIALS AND METHODS. Utilizing a multistage stratified sampling, 2310 patients were diagnosed in the imaging centers of the provincial capitals in Iran between 2007 and 2008. These were composed of 1755 patients who were settled residents of 24 provincial capitals. Data on the regional drinking water composition, obtained from an accredited registry, and their relationships with the region's incidence of urinary calculi were evaluated by metaregression models. The stone risk index (defined as the ratio of calcium to magnesium-bicarbonate product in drinking water) was used to assess the risk of calculus formation. RESULTS. No correlation was found between the urinary calculus incidence and the amount of calcium, bicarbonate, or the total hardness of the drinking water. ...

Energy Technology Data Exchange (ETDEWEB)

The LiMnO{sub 2} lamellar oxide, obtained by exchange reaction from its sodium homologue {alpha}-NaMnO{sub 2}, has been used as a positive electrode for lithium batteries. After the first electrochemical cycle, the shape of the potential-composition curve changes and indicates a change in the structure. This modification changes imperceptibly at each cycle and after about 40 cycles, a stationary state is reached. Powder spectra refinement using the Rietvelt method shows a migration of manganese ions from the thin sheets towards the inter-sheet space. After a single cycle, 8% of the manganese ions are already present in the lithium site and this rate reaches 13% after 3 cycles. During long cycling, a redistribution of ions and vacancies inside the cfc oxygenated pile leads to a structure very similar to the LiMn{sub 2}O{sub 4} spinel. This structure evolution is to be compared with the one obtained from the orthorhombic variety of LiMnO{sub 2} but the modification ...

International Nuclear Information System (INIS)

Cyclic voltammograms of SUS 304 stainless steel in various neutral solutions such as Na_2SO_4 at high temperature were measured, as a successive study to previous report in which effects of temperature and pH on polarization behavior of stainless steel were studied. In this measurement Ag/AgCl reference electrode and platinum counter electrode were used in a static autoclave lined with inconel. Passive films formed in various conditions were analysed by electron diffraction and Auger spectroscopy. Results obtained were compared with anodic behavior of iron, chromium and nickel and with thermodynamical stabilities of their compounds. The main results are summarized as follows. (1) Stainless steel shows such electrochemical behavior as active dissolution, passivation and transpassivation in a deaerated neutral solution at 250"0C after fully reductive treatment of the specimen. In air-saturated solution, the peak of active dissolution is not observed. In the passive range there are ...

Energy Technology Data Exchange (ETDEWEB)

Electronic properties of passive films formed on Fe at various applied potentials in pH 8.5 buffer solution were examined through the photocurrent measurement and impedance spectroscopy. Passive film formed on Fe at relatively low potentials was found to be r-FeOOH layer and internal r-Fe{sub 2}O{sub 3} layer. However, the r-FeOOH layer became unstable and disappeared at potentials below 400mV and hence may be an adsorbed layer. An electronic band structure model for the passive film of Fe was suggested on the basis of the spinel band model with involving two types of electronic excitation processes, i. e., the p-d and the d-d transition together. The effects of applied potential on the photocurrent behaviors of the passive film on Fe were explained appropriately by separating the photocurrent spectra depending on the transition type. The Mott-Schottky behavior for the passive film on Fe and the photocurrent variation with applied potential were also analyzed in ...

Energy Technology Data Exchange (ETDEWEB)

The formation and breakdown of the passive films on stainless steels are mainly controlled by ionic and electronic transport processes. Both these processes are in part controlled by the electronic properties of the oxide film. Consequently, it is vital to gain a detailed perception of the electronic properties of the passive films together with structural and compositional information for a comprehensive understanding of mechanisms behind passivity and localised corrosion. As a step towards this goal the passive films formed on two main austenitic stainless steels AISI 316L and AISI 304L in borate solution were characterised by in situ Raman spectroscopy and photocurrent spectroscopy coupled with electrochemical measurements. This revealed the formation of an Fe-Cr spinel as the dominant constituent in the passive films with more Cr enrichment in the oxide film on 316L than that of 304L. Bandgap readings and semiconductivities of the two stainless steels suggested ...

Energy Technology Data Exchange (ETDEWEB)

The electrochemical behaviour of passive films formed on one austenitic stainless steel (AISI 304) and one ferritic stainless steel (AISI 446) in solutions with pH between 0.6 and 8.4 was studied by capacitance measurements and photocurrent spectroscopy. Compositional characterization of the passive films was done by X-ray photoelectron spectroscopy. The capacitance increases with decreasing pH. Doping densities evaluated from Mott-Schottky plots are in the range 2-6 x 10{sup 20} cm{sup -3} and increased with the pH in the neutral/alkaline range while in pH 0.6, values above 10{sup 21} cm{sup -3} were found. The bandgap energy indicates two transitions, at 2.5-2.8 and 3.2 eV. The analytical data reveal that, as the pH increased, the films become enriched in Fe(II) and Fe(III), whereas the Cr(III) gradually decreases. The films formed at very low pH had a behaviour that contrasts with that of the films formed in the neutral/alkaline media. The films are described by a bilayer structure, ...

Energy Technology Data Exchange (ETDEWEB)

A new preparation method for LiNiVO{sub 4} has been developed. LiNiVO{sub 4} can be readily obtained from the solid state reaction of LiNiO{sub 2} and V{sub 2}O{sub 3} or V{sub 2}O{sub 5} at 700 C for 2 h in air. The quarternary Li-Ni-V-O reaction is strongly dependent on vanadium starting materials, reaction environment atmosphere, reactant stoichiometry and synthesis temperature. Individual particles of LiNiVO{sub 4} powders are well-formed crystallites shown clearly by scanning electron microscopy results to be in the shape of an octahedron. Powder X-ray diffraction studies of this crystalline material indicate that LiNiVO{sub 4} has an inverse spinel structure different from that of known cathode materials such as LT-LiCoO{sub 2} and LiMn{sub 2}O{sub 4}. The Li/LiNiVO{sub 4} cell can be charged and discharged at about 4.8 V versus metallic Li. To our knowledge, this is the Li intercalation reaction with the highest voltage known. (orig.) 14 refs.

International Nuclear Information System (INIS)

Full text: In Hungary, the main goal is that the Hungarian regulations should meet with the EU Directive No. 96/29. For this aim, a surveying project has been launched in order to collect all relevant information about the Hungarian TENORM situation. This surveying programme covers a lot of data collection (work activities, disposal places, residue quantities) and radiological measurements on the TENORM site. The Hungarian situation of TENORM definitely differs from other countries in the aspect of occurrence forms of natural sources (or in the imported raw materials), in the quantities of exploitation, in the level of the radioactivity and in the applied technological processes. Firstly, those work activities have been choosen where the huge amount of residues have been produced. The other criteria is that the activity concentration in a great portion of the given residues is much higher than the average activity concentration of the typical Hungarian soil. After filtering and ...

Energy Technology Data Exchange (ETDEWEB)

Extruded and hot-rolled 200 C {proportional_to} 500 C AZ31B plates were studied their texture using ODFs analysis. The as-extruded specimen has the strongest intensity of (0001)-ND fiber and 300 C and 400 C hot-rolled ones have the next, but the 200 C hot-rolled one has the lowest intensity. Compared with the corresponding tensile properties, this feature evidents that a pronounced (0001) basal texture will reduce ductility of AZ31B alloy. The ODFs results also indicate that (05 anti 52)- and (01 anti 10)-ND fibers are related to the ductility of AZ31B alloy. (orig.)

Energy Technology Data Exchange (ETDEWEB)

Pilot plant tests have been conducted to evaluate sodium thiosulfate as an oxidation inhibition additive in five lime/limestone slurry flue gas desulfurization processes. It was found that the oxidation rate of absorbed sulfur dioxide (SO)/sub 2/ was reduced by more than 50 percent in the presence of 100 to 200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvement in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

Energy Technology Data Exchange (ETDEWEB)

The article gives results of pilot-plant tests to evaluate sodium thiosulfate as an oxidation-inhibition additive in five lime/limestone slurry flue-gas desulfurization processes. It was found that the oxidation rate of absorbed SO/sub 2/ was reduced by more than 50% in the presence of 100-200 ppm of thiosulfate ion in the scrubbing slurry. Calcium sulfate dihydrate (gypsum) scaling was eliminated and the unsaturated (with respect to gypsum) operation mode was maintained by the addition of sodium thiosulfate. Other benefits of sodium thiosulfate addition observed at the pilot plant included improvement in solids dewatering properties for limestone processes and improvements in SO/sub 2/ removal efficiency for magnesium-enhanced lime/limestone processes.

Energy Technology Data Exchange (ETDEWEB)

Counter-current regeneration of 2-stage sodium zeolite softeners has been employed in reducing hardness leakage level of steamflooding water to less than 1 ppm when raw water contains as much as 5,000 ppm of the total dissolved solids. Hardness leakage is caused by sodium displacement of calcium and magnesium from the bottom of the exchanger bed. This study presents nomographs providing for rapid calculations to be made, for which a convenient operational mode does not already exist. The nomographs relate the hardness leakage as a function of salt quality and influent water quality and present solutions for predicting the leakage level, salt quality requirement or the treatability of raw water required for steamflooding projects.

International Nuclear Information System (INIS)

Microstructure and properties of a Mg AZ31B laser beam weld without filler are studied using electron microscopy, X-ray diffraction and mechanical tests. The microstructure of the weld is characterized by a narrow heat affected zone, columnar grains and precipitate coarsening in the fusion zone. Texture in the fusion zone is significantly different from the texture of the base material. The residual stress distribution observed is similar at the top and the bottom of the weld, maximum tensile residual stress values are observed in the fusion zone. Tensile tests reveal differences in the mechanical behavior of the fusion zone and the parent material, which can be related to the differences of texture and the resulting deformation mechanisms.

British Library Electronic Table of Contents (United Kingdom)

Normally, concrete technologists attribute salt weathering, salt crystallization or physical attack to the deterioration of concrete that is partially exposed to sulfate environment. However, there are few convincing evidences supporting this view. The purpose of this paper is to check by means of extensive micro-analysis if traces of sulfate crystals are present in the paste. This would enable to verify in a direct way whether salt weathering really causes cement paste damage or not.In this research, cement paste and cement?fly ash paste specimens were partially exposed to sodium sulfate and magnesium sulfates solution under a constant storage condition (20 ? 2 ?C, and 60 ? 5% RH) and a sharply fluctuating environment (40 ? 2 ?C and 35 ? 5% RH for 24 h, then 10 ? 1 ?C and 85 ? 5% RH, also...

International Nuclear Information System (INIS)

This study concerns the Souss upstream basin. The objective is to investigate the characteristics of surface water and groundwater, to assess the impact of artificial recharge as reinforcement of the natural replenishment and assess the renewal of groundwater under semi-arid area. Two major water types are observed: (i) surface waters and upstream springs (least mineralized) and (ii) all groundwater samples (prevailing calcium and magnesium bicarbonate water type). Water isotopes show a low evaporation of precipitations during infiltration. Impoverishment in heavy isotopes is the characteristic of mountain rainfalls, or of a climate colder and wetter than present. Carbon-14 activities (34-94 pmc) indicate a long residence time. The artificial recharge is low compared to the reservoir volume, due to which the renewal rate is also low.

International Nuclear Information System (INIS)

Corrosion tests of titanium alloys VTI-0, OT4, VT5-1 and steel Kh18N1OT in 10% and 18% HCl with additions of carnallite at 40 deg C have been carried out. It has been established that titanium alloys in 10% and 18% HCl containing 5 and 10% carnallite are sufficiently corrosion resistant in the presence of 0.1-1% FeCl or HNO_3 and can be used for manufacturing the equipment of recirculation gas scrubbers. Steel Kh18N10T is unstable in all the media tested. It is subjected to intensive pitting. Specimens of steel Kh18N10T have also revealed edge cracking.

British Library Electronic Table of Contents (United Kingdom)

Commercial rolled magnesium sheets of alloys AZ31 (Mg-3 mass%Al-1 mass%Zn) and ZE10 (Mg-1 mass% Zn-<1 mass% Rare Earths) in O-temper condition were used for blanking experiments near room temperature. A serrated fracture surface can be observed in case of AZ31 but not in case of ZE10. During the shearing process of the AZ31 sheet, many micro cracks parallel to the sheet plane are generated in the shearing zone. These micro cracks lead to the formation of loose particles during the shearing operation, which interfere with further processing of the part and incur additional costs by increasing the scrap rate. It is found that the strong basal texture of this alloy is an important reason for the generation of such serrated cracks. In this paper a new method of selective texture modification i...

International Nuclear Information System (INIS)

Fractionation of isotopes of the alkali metals and the alkaline earth metals in ion exchange chromatography of their chlorides was studied. The heavier isotopes of potassium and rubidium were found to be preferentially fractionated into the ion exchanger phase while the lighter isotopes of lithium, magnesium, calcium and strontium were enriched in the exchanger phase. This can be interpreted as a resultant of the relative significance of isotope effect upon dehydration and isotope effect accompanying the phase change of the hydrated metal ion. Found was no evidence of anomalous isotope effect attributable to the odd-even difference in mass number of isotopes. Based on the spectroscopic and solution chemical data (experimental and theoretical), the isotopic reduced partition function ratios of the hydrated alkaline metal ions and stretching force constants of metal ion-hydrating water bonds were estimated. (author).

Energy Technology Data Exchange (ETDEWEB)

The structure and catalytic properties of 2 wt.-% Pd/SiO/sub 2/ catalysts promoted with 2 wt.-% MgO and 0.2-5 wt.-% iron have been investigated. Catalysts were characterized by TPR, hydrogen chemisorption, and Moessbauer spectroscopy and their catalytic performance in methanol formation was also measured. At 16 at.-% iron a sharp maximum was observed in the activity which can be interpreted as being due to simultaneous promotion with iron and MgO. Independent mechanisms of promotion were found for the two modifiers: iron influenced the metallic component by forming bimetallic PdFe particles while MgO changed the properties of silica in a favourable way. 6 figs., 29 refs., 1 tab.

International Nuclear Information System (INIS)

The synthesis, characterization, and some analytical applications of a new triazine resin are described. Separation of group IB, IIB, VIB, and VIIB metal ions from group VIII metal ions is achieved by this PDT-4 resin. Calcium(II) and magnesium(II) are taken up at pH = 6, 0.1 M acetate and are eluted at pH = 6, 0.1 M sodium nitrate. Copper(II) is retained at pH = 6, 0.1 M acetate and pH = 1 hydrochloric acid and is eluted subsequently by 5 M perchloric acid. Molybdenum(VI) is sorbed selectively from 0.1 N sulfuric acid or hydrochloric acid and is eluted in a tight band by 0.1 N sodium hydroxide. Numerous rapid column chromatographic separations are reported using this new resin, including analysis of NBS standard samples.

Energy Technology Data Exchange (ETDEWEB)

Effects of ions of Group IA, IIA, IIIB, and VIIB elements on the cathodic deposition of a molybdenum were investigated in a KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt at 773 K (500/degree/C). The results can be summarized as follows: The addition of potassium, rubidium, cesium, and barium cations and fluorine anions to the KCl-LiCl (eutectic)-MoCl/sub 3/ molten salt is effective in depressing the cathodic deposition of the molybdenum subchloride, which hinders the smooth, flat electrodeposition of molybdenum. The addition of lithium, sodium, magnesium, calcium, strontium, and aluminum cations and bromine and iodine anions promotes the undesirable cathodic deposition of the molybdenum subchloride.

Energy Technology Data Exchange (ETDEWEB)

The Partnership for a New Generation of Vehicles (PNGV) program intends to develop new designs for automobiles that will reduce fuel consumption by two thirds but otherwise have price, comfort, safety, and other measures of performance similar to the typical automobile now on the market. PNGV vehicle designs are expected to substitute lightweight materials, such as aluminum, magnesium, carbon-reinforced polymer composites, glass-reinforced polymer composites, and ultra- light steel, for heavier materials such as steel and iron in automobile components. The target mass of a PNGV vehicle is 1,960 pounds, as compared to the average current vehicle that weights 3,240 pounds. Other changes could include the use of different ferrous alloys, engineering changes, or incorporation of advanced ceramic components. Widespread adoption of these vehicle designs would affect materials markets and require concurrent development and adoption of supporting technologies to supply the ...

Energy Technology Data Exchange (ETDEWEB)

A family of mixed LiCo{sub y}Ni{sub (1-y)}VO{sub 4} (y=0.2, 0.5 and 0.8) compounds of potential use as high voltage cathode materials in lithium batteries, has been synthesized and characterized. The X-ray diffraction analysis showed that these compounds adopt an inverse spinel structure where in average 85% of the Ni{sup 2+} and Co{sup 2+} ions occupy octahedral sites and the other 15% occupy tetrahedral sites with the V{sup 5+} ions, although this occupation share is somewhat influenced by the preparation temperature. The annealing temperature plays also a key role in determining the particle size, as demonstrated by scanning electron microscope analysis. Cycling voltammetry tests showed that the lithium insertion-deinsertion process in the LiCo{sub y}Ni{sub (1-y)}VO{sub 4} electrode materials occurs reversibly around 4.3-4.4 V vs. Li, as also confirmed by cycling tests. The cycling capacity is somewhat modest; however, the trend of the cycling curves leads to ...

Energy Technology Data Exchange (ETDEWEB)

LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} was prepared through a solid-state reaction using various Ni precursors. The effect of precursors on the electrochemical performance of LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} was investigated. LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} made from Ni(NO{sub 3}){sub 2}.6H{sub 2}O shows the best charge-discharge performance. The reversible capacity of LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} is about 145 mAh g{sup -1} and remained 143 mAh g{sup -1} after 10 cycles at 3.0-5.0 V. The XRD results showed that the precursors and the dispersion methods had significant effect on their phase purity. Pure spinel phase can be obtained with high energy ball-milling method and Ni(NO{sub 3}){sub 2}.6H{sub 2}O as precursor. Trace amount of NiO and Li{sub 2}MnO{sub 3} phase were detected in LiNi{sub 0.5}Mn{sub 1.5}O{sub 4} with manual-mixture method and using Ni(CH{sub 3}COO){sub 2}.6H{sub 2}O, NiO and Ni{sub 2}O{sub 3} as precursors. (author)

Energy Technology Data Exchange (ETDEWEB)

Lherzolite-bearing basanitic magmas of Quaternary age have erupted to form maars, lava/cinder cones and lava flows in two volcanic fields (Ventura and Santo Domingo) in the central Mexican state of San Luis Potosi. The systematics of the radiogenic isotopes of Sr, Nd, and Pb and the relationship between these parameters and elemental compositions are used to investigate the petrogenesis of the volcanic rocks and the nature of their mantle sources. Sr and Nd isotopic data are presented for 19 basanitic rocks, 5 kaersutites, and 6 lherzolitic xenoliths; Pb data presented for the same 19 volcanic rocks and 4 of the 5 kaersutites. The isotopic compositions for all of these samples fall within the mantle range defined by MORBs and OIBs. The basanites generally plot within the OIB field on isotopic diagrams; most of the kaersutites are displaced to slightly more-depleted (i.e. MORB-like) values than the volcanic samples and the xenoliths, with one exception, are significantly more-depleted ...

Energy Technology Data Exchange (ETDEWEB)

The exchange charge model (ECM) of crystal field is utilized to provide the theoretical explanation of the ground state absorption and the excited state absorption observed for the octahedrally coordinated Ni{sup 2+} ions in the spinel MgAl{sub 2}O{sub 4}. The ECM enables modeling of the crystal field parameters (CFPs) for the impurity ions based on the crystal structure data of the host lattice. To ensure the reliability of the CFPs, the convergence of the CFP values with the increasing number of the coordination spheres taken into account in the ECM calculations is considered. The trigonal CFPs B{sub 2}{sup 0},B{sub 4}{sup 0}andB{sub 4}{sup -3} determined by the ECM, together with the appropriate Racah parameters B and C, serve as input to two crystal field analysis computer packages, which compute the energy level schemes within the whole 3d{sup 8} configuration. The cubic approximation utilizing only one CFP Dq is also discussed. Basic features of the ground ...

International Nuclear Information System (INIS)

Experimental results of compatibility tests on ceramics-metal bonded structures performed under high heat flux conditions in splash test apparatus are reported. Emphasis is placed on results of the channel wall design and its critical operating conditions under MHD environment. The module design of one cold type and three semihot type insulators have been tested. These materials were Al_2O_3, Al_2MgO_4, LaAlO_4, MgO and Sialon ceramics. The methods of cold type ceramics-metal bonding structure were studied on Al_2O_3 and Spinel spray coating technology. The refractory metallizing and ceramics-metal graded structure manufactured by HIP technologies were applied to bonding between the MgO or LaAlO_4 and metallic cooling system. The Sialon non-bonding structure was tested with mechanical supported cooling system by shrinc fitting method. The results indicated that the bonding structures made of the MgO(MG-S) with Copper and Fe-Ni Alloy relaxation layers and MgO(MG-NC) ...

Energy Technology Data Exchange (ETDEWEB)

The development of rechargeable lithium batteries with a high mass capacity, made with non-toxic and low cost materials is an important industrial challenge. Morphological and structural modifications occurring in the electrode materials during charge-output cycles should not lower the electrochemical characteristics and the cycling properties of the battery. Thus the structure of electrode materials must be sufficiently deformable and stable to support the constraints linked with lithium intercalation and de-intercalation (ions and electrons absorption/extraction). The aim of this work is to explain some characteristics (mass capacity, ions and electrons mobility, cycling) using the relation between some mechanisms of lithium insertion (sites occupation, lattice reduction mods) and the nature of atoms and chemical bonds (covalence, ionicity). This approach is developed on 2-D models of crystallized and vitreous sulfur compounds (CdI{sub 2} type) with a large inter-sheet distance, and ...

Energy Technology Data Exchange (ETDEWEB)

Coal ash is a substance that has been mixed into minerals in the earth`s crust during their coalification process. Estimation was made on what kinds of mineral composition have been mixed into coals. Noted first was the kinds of compounds contained in the ash, wherein the ratios of mass in the compounds and minerals were correlated, and selection was made on minerals which are thought correlated. The selection criterion was based on minerals containing silica, alumina, iron oxide, lime and magnesium as compounds. Then, a phase equilibrium line diagram was used to estimate compositions and melting points of minerals which are thought to have been produced from these compounds. By comparing the estimation with the measured melting points of the ashes, mineral compositions thought reasonable were all selected. Assumption was possible on minerals that are thought to have been transferred into coal ash. Compound indications of ashes from 29 kinds of the world`s typical ...

Energy Technology Data Exchange (ETDEWEB)

Adsorptive removal of Pb(II) ions from aqueous solution onto a non-activated charcoal (CC) of oak wood origin was studied in comparison with an activated carbon of coal origin. The adsorption capacity for Pb(II) of the non-activated charcoal increased significantly with deceasing particle diameter, whereas the activated carbon (AC) exhibited approximately constant capacity for Pb(II) adsorption as a function of particle size. Adsorption to the ashes prepared from the non-activated charcoal and the activated carbon was also investigated to examine the role of mineral ash. Although the ash from the activated carbon did not show any Pb(II) adsorption, the ash from the charcoal was very effective for Pb(II) adsorption. Furthermore, Pb(II) was hardly adsorbed when the ash was removed from the non-activated charcoal by acid treatment. Based on the results, the adsorption sites for Pb(II) are considered to be acidic surface functional groups on the external and internal surfaces for the ...

Energy Technology Data Exchange (ETDEWEB)

Fine-grained AZ31 magnesium alloy sheets were prepared through hot rolling process. The superplastic properties of hot-rolled AZ31 Mg alloy was examined by uniaxial tensile tests at a temperature range 250{proportional_to}450 C and strain rate range 0.7 x 10{sup -3}{proportional_to}1.4 x 10{sup -1} s{sup -1}. Optical and scanning electronic microscope (SEM) were used to observe the microstructure evolution and fracture behavior in superplastic deformation of AZ31 Mg alloy and the values of deformation activation energy at various temperatures were calculated. It is demonstrated that, the hot-rolled AZ31 alloy begins to exhibit superplasticity from 300 C and a maximum elongation of 362.5% is obtained at 400 C and 0.7 x 10{sup -3} s{sup -1}. In the temperature range 300{proportional_to}400 C, the dominant superplastic deformation mechanism is grain boundary sliding (GBS) controlled by grain boundary diffusion and the influence of temperature on the fracture behavior ...

Science.gov (United States)

Ion implantation has been applied to magnesium-doped Al[sub 0.5]In[sub 0.5]P to produce high resistivity regions for the first time. Hydrogen, oxygen, and argon ions were implanted at a base dose ranging from 5[times]10[sup 12] to 5[times]10[sup 14] cm[sup [minus]2] and annealed from 400 to 900 [degree]C. Hydrogen did not appreciably compensate the In[sub 0.5]Al[sub 0.5]P layer while oxygen and argon produced sheet resistances up to 1[times]10[sup 9] [Omega]/[open square]. After annealing at 800 [degree]C, regions with high dose oxygen implants maintained a sheet resistance above 1[times]10[sup 7] [Omega]/[open square], while regions with high dose argon implants recovered most of the unimplanted conductivity.

International Nuclear Information System (INIS)

Separate effect of impurities and alloying additions of phosphorus, silicon, boron, carbon, sulphur, magnesium, copper, aluminium and molybdenum on the tendency to intergranular corrosion (IGC) of quenched highly pure steel Fe-20% Cr-20Ni in boiling solution 27% HNO_3+40 g/l Cr"6"+, as well as in sulphuric and nitric acids mainly at potentials, corresponding to repassivation range, has been studied. It is shown that steel susceptibility to IGC depends on impurity nature and to a high extent is determined by the potential value independent of the way of its achieving. The most unfavourable effect on stability of grain boundaries is produced by microadditions of boron as well as by impurities of phosphorus and silicon. To ensure increased corrosion resistance of the investigated steel against IGC in highly oxidative media the pontent of phosphorus and silicon impurities unit should not exceed 0.01 and 0.2% respectively. At that, boron introduction into steel as a ...

International Nuclear Information System (INIS)

The effect of concentration on the corrosion behavior of Mg-based alloy AZ91D was investigated in ethylene glycol-water solutions using electrochemical techniques i.e. potentiodynamic polarization, electrochemical impedance measurements (EIS) and surface examination via scanning electron microscope (SEM) technique. This can provide a basis for developing new coolants for magnesium alloy engine blocks. Corrosion behavior of AZ91D alloy by coolant is important in the automotive industry. It was found that the corrosion rate of AZ91D alloy decreased with increasing concentration of ethylene glycol. For AZ91D alloy in chloride >0.05 M or fluoride 0.05 M for fluoride containing ethylene glycol solution, some inhibition effect has been observed. The corrosion of AZ91D alloy in the blank can be effectively inhibited by addition of 0.05 mM paracetamol that reacts with AZ91D alloy and forms a protective film on the surface at this concentration as confirmed by surface ...

International Nuclear Information System (INIS)

We studied the effects of co-doping with Li and Al on the energy gaps of MgB2 by performing point-contact Andreev-reflection spectroscopy (PCAR) in polycrystalline Mg1-x(Al?Li1-?)xB2 samples with x?0.4. Even though the lattice parameters and the critical temperature of the compound simply scale with the effective Al content ?x, irrespective of the Li concentration, the energy gaps do not. In particular, for a given effective Al content, the comparison with Mg1-y(Al)yB2 with y = ?x shows that the ? bandgap is practically the same while the ? bandgap is higher. A clear gap merging is observed in the most doped sample (x = 0.4) when Tc<20 K. The results are discussed within the two-band Eliashberg theory and compared to the outcomes of first-principles calculations of the effects of Li and Al co-doping on the electronic structure of magnesium diboride.

International Nuclear Information System (INIS)

NaCl doped MgCl_2.nEtOH adducts were prepared by ball-milling MgCl_2.2.5EtOH with NaCl. Both the ball-milled MgCl_2.nEtOH/NaCl mixture and pure MgCl_2.2.5EtOH adducts were analyzed by X-ray diffraction (XRD), transmission electron microscope (TEM), thermogravimetry (TG) and differencial scanning calorimetry (DSC). A simple MgCl_2.nEtOH/NaCl mixture without ball-milling treatment was also studied for comparison. Two kinds of mixed crystals, Na_2MgCl_4 and NaMgCl_3, were found to be formed in a ball-milled mixture that contained 16 mol.% NaCl. TG and DSC analysis of the samples also provided indirect evidences supporting the presence of the mixed crystals in the ball-milled mixture. Adding certain amounts of NaCl in MgCl_2.2.5EtOH adduct, either by co-milling or by simple mixing, greatly increased the thermal stability of the adduct, but thermal decomposition behaviour of the ball-milled mixture was still different from that of a simple mixture.

International Nuclear Information System (INIS)

Alloy 800 and Alloy 600 are well known for their resistance to corrosion in an aqueous medium at high pressure and temperature, for which they have been widely used for more than 3 decades in different structural components of water refrigerated nuclear reactors, especially as material for the steam generator tubes (SG) in these nuclear plants. The SG tubes in the Atucha I and Embalse Nuclear Plants are made with Alloy 800. The speed of corrosion of these materials in a reactor's refrigerant medium, while very small is perfectly measurable and can be described by parabolic or logarithmic type kinetics. In other words this speed is high in the first states of growth during the formation of a protective oxide film but then drops to almost stationary values. One characteristic of these films is the formation of a double layer (or duplex): i) an internal adhering layer, of approximately constant thickness, formed by small microcrystals (#<=#0.05 mm), ii) a less adhering external one, ...

International Nuclear Information System (INIS)

Statements about the dynamic processes of uptake, transport, and deposition of Ca and Mg in norway spruce and Scots pine are made in this paper. Concerning the storage of these elements it is shown that there are great differences in their functional importance in cell metabolism. There is evidence that the role of Mg in enzyme and protein metabolism is of far greater significance for the understanding of Mg-deficiency symptoms than its function as the central atom of the chlorophyll complexes. In regard to the transport and especially to the incorporation of Ca into the needles differences between species were evident, expressing the special status of pine among the gymnosperms. With increasing needle age an accumulation of Ca-oxalate crystals, which are physiologically inert, could be proved for the studied conifers. This was interpreted as a 'detoxication' from surplus Ca to hold constant the level of the physiologically active fraction. Accordingly, the low Ca-contents of yellowed ...

Energy Technology Data Exchange (ETDEWEB)

The first Russian reprocessing facility, known as RT-1 (located at PA-Mayak in Ural region) was started on the radiochemical plant base in 1977. Nowadays RT-1 is the sole operating reprocessing plant in Russia. The main features of RT-1 is its broad spectrum of reprocessing spent nuclear fuels (SNF). The following spent fuel types are reprocessed: -) SNF from PWR reactors (WWER-440) and FB reactor (BN-600); -) SNF of transport ship reactors; -) production reactors SNF; -) research reactor spent nuclear fuel. The world-known technological processes are used at RT-1, but there are the following distinctive features. First, the universality of the three technological lines which allows not only the reprocessing of various SNF kinds, but also to implement the combined reprocessing of some types of them. Secondly, extraction of neptunium during SNF reprocessing which is used to implement its separate storage and for radioisotope production. Thirdly, target enrichment of recycled uranium is ...

Energy Technology Data Exchange (ETDEWEB)

The pharmacology of the alpha-2 adrenoceptor of the human adipocyte was improved by using some new alpha-2 antagonists from different chemical families (imidazolines, benzazepines and benzofuroquinolizines) in biological and binding assays. Moreover, investigations were also carried out to define the binding properties of a new imidazolinic antagonist, RX821002 (2-(2-methoxy-1,4-benzodioxan-2yl)-2-imidazoline), which could be a potential radioligand. (3H)RX821002 binding was very rapid and reversible. Saturation isotherms indicated that (3H)RX821002 labeled, with high affinity, a homogeneous population of noninteracting binding sites with a mean Kd of 0.98 +/- 0.05 nM (n = 6). The binding of (3H)RX821002 on the human fat cell alpha-2 adrenoceptor displayed a specificity which is strictly similar to that obtained with (3H)rauwolscine and which is classical for an alpha-2 A adrenoceptor. The binding parameters of (3H)RX821002 were compared with those obtained with the classical alpha-2 ...

International Nuclear Information System (INIS)

It is well known that one of the main advantages of the high speed forming (HSF) processes is the improvement in the forming limits of the used materials.Using the Electromagnetic Forming (EMF) technology two materials have been tested with different mechanical and physical properties: the AA5754 aluminium and the AZ31B magnesium alloys.The EMF process principle can be described as follows: A significant amount of electrical energy is stored in a bank of capacitors which are suddenly discharged releasing all the stored energy. This electric discharge runs through a coil which generates an intense transient magnetic field. At the same time transient Eddy currents are induced in the electrically conductive part placed some millimetres far from the coil. Another intense magnetic field is generated due to those Eddy currents but on the opposite direction as the one generated by the coil. A big magnetic repulsion force is created between the part and the coil. This ...

International Nuclear Information System (INIS)

The effects of catalytic metal additives on the hydrogen desorption properties of the submicrocrystalline magnesium hydride (#beta#-MgH_2) formed after hydrogenation of the Mg + 10 wt.%X (X = V, Y, Zr) mechanically (ball) milled composites were studied. The composites with catalytic metals were processed by controlled mechanical milling (CMM) in the magneto-mill Uni Ball Mill 5 under protective Ar atmosphere. X-ray diffraction of the milled powders revealed the formation of Mg nanograins (50-60 nm range) interdispersed with the nanograined metal additives within the powder particles. Scanning electron microscopy showed particle size reduction after milling. After activation and hydrogenation in a Sieverts-type apparatus under about 2 MPa pressure of hydrogen, the tetragonal #beta#-MgH_2 hydride co-exists with the small amount of retained unreacted Mg phase and the small amount of MgO in all three composites. The #beta#-MgH_2 phase after hydrogenation is ...

Energy Technology Data Exchange (ETDEWEB)

Magnesium-based alloys are among the promising materials for hydrogen storage and fuel cell applications due to their high hydrogen content. In the present work, we investigated the hydrogen release/uptake properties of the Mg-Ti-H system. Samples were prepared from the mixtures of MgH{sub 2} and TiH{sub 2} in molar ratios of 7:1 and 4:1 using a high-energy-high-pressure (HEHP) mechanical ball-milling method under 13.8 MPa hydrogen pressure. Thermogravimetric analysis (TGA) showed that a relatively large amount of hydrogen (5.91 and 4.82 wt.%, respectively, for the above two samples) was released between 126 and 313 C while temperature was increased at a heating rate of 5 C min{sup -1} under an argon flow. The onset dehydrogenation temperature of these mixtures, which is 126 C, is much lower than that of MgH{sub 2} alone, which is 381 C. The activation energy of dehydrogenation was 71 kJ mol{sup -1}, which is much smaller than that of as-received MgH{sub 2} (153 kJ ...

Energy Technology Data Exchange (ETDEWEB)

The reverse micelle catalyst preparation method has been used to prepare catalysts on four supports: magnesium oxide, carbon, alumina- titania and steamed Y zeolite. These catalysts were not as active as a reference catalyst prepared during previous contracts to Union Carbide Corp. This catalyst was supported on steamed Y zerolite support and was impregnated by a pore-filling method using a nonaqueous solvent. Additional catalysts were prepared via pore- filling impregnation of steamed Y zeolites. These catalysts had levels of cobalt two to three and a half times as high as the original Union Carbide catalyst. On a catalyst volume basis they were much more active than the previous catalyst; on an atom by atom basis the cobalt was about of the same activity, i.e., the high cobalt catalysts` cobalt atoms were not extensively covered over and deactivated by other cobalt atoms. The new, high activity, Y zerolite catalysts were not as stable as the earlier Union Carbide ...

Energy Technology Data Exchange (ETDEWEB)

To establish the optimum barium-based reduced-laxative tagging regimen prior to CT colonography (CTC). Ninety-five subjects underwent reduced-laxative (13 g senna/18 g magnesium citrate) CTC prior to same-day colonoscopy and were randomised to one of four tagging regimens using 20 ml 40%w/v barium sulphate: regimen A: four doses, B: three doses, C: three doses plus 220 ml 2.1% barium sulphate, or D: three doses plus 15 ml diatriazoate megluamine. Patient experience was assessed immediately after CTC and 1 week later. Two radiologists graded residual stool (1: none/scattered to 4: >50% circumference) and tagging efficacy for stool (1: untagged to 5: 100% tagged) and fluid (1: untagged, 2: layered, 3: tagged), noting the HU of tagged fluid. Preparation was good (76-94% segments graded 1), although best for regimen D (P = 0.02). Across all regimens, stool tagging quality was high (mean 3.7-4.5) and not significantly different among regimens. The HU of layered ...

International Nuclear Information System (INIS)

A one-year study was conducted to determine the impacts of acid min drainage (AMD) on the Black Creek watershed in Wise County, Virginia. Water quality, metal content of sediment and water column, soil pH, macroinvertebrate assemblages, habitat assessment and toxicity testing were used to assess the impact in the watershed. A total of 22 sites in the creek and surrounding watershed were actively monitored. This included six primary sources of AMD. Conductivity measurements > 1,000 microhmos/cm were found at eight sites and pH was consistently below 6.0 at seven. Of six metals analyzed, magnesium was highest in the water column, ranging from 16.5 mg/L to 130 mg/L. Aluminum and iron were both elevated in the sediment with iron concentrations as high as 176,000 mg/kg. An increase in sediment metal concentrations was noted when progressing downstream in the creek. Of nine high wall and spoils areas sampled, soil pH was acidic in eight sites, ranging from 5.5 to 3.1. ...

International Nuclear Information System (INIS)

The rare earth metal rich compounds RE4NiMg (RE=Y, Pr-Nd, Sm, Gd-Tm, Lu) were synthesized from the elements in sealed tantalum tubes in an induction furnace. All compounds were investigated by X-ray diffraction on powders and single crystals: Gd4RhIn type, space group F4-bar 3m, Z=16, a=1367.6(2) pm for Y4NiMg, a=1403.7(3) pm for Pr4NiMg, a=1400.7(1) pm for Nd4NiMg, a=1386.5(2) pm for Sm4NiMg, a=1376.1(2) pm for Gd4NiMg, a=1362.1(1) pm for Tb4NiMg, a=1355.1(2) pm for Dy4NiMg, a=1355.2(1) pm for Ho4NiMg, a=1354.3(2) pm for Er4NiMg, a=1342.9(3) pm for Tm4NiMg, and a=1336.7(3) pm for Lu4NiMg. The nickel atoms have trigonal prismatic rare earth coordination. These NiRE6 prisms are condensed via common edges to a three-dimensional network which leaves voids for Mg4 tetrahedra and the RE1 atoms which show only weak coordination to the nickel atoms. The single crystal data indicate two kinds of solid solutions. The RE1 positions reveal small RE1/Mg mixing and some compounds also show Ni/Mg ...

Energy Technology Data Exchange (ETDEWEB)

Fuel cells based on solid oxides ('SOFC') are excellent alternative devices for power generation, when they are operated at high temperature, e.g. above 600 C. Having only fixed parts for the power generating part of the device is only one advantage of the fuel cell. Due to their unique design, these devices offer a maximum of efficiency for energy conversion compared to conventional power generating systems, which are mainly based on turbines. One aim of this thesis is the examination of alternative electrolyte and cathode materials for the SOFC applications at reduced temperatures, which means in the temperature range between 600 C and 750 C. For the first main task, several materials from the oxygen ion conducting electrolytes were selected. Different strontium and magnesium doped lanthanum gallate (LSGM) materials with additional transition metal doping were selected and prepared via two different preparation methods. The optimum calcining ...